Rainier Mesa CAU Infiltration Model using INFILv3

Energy Technology Data Exchange (ETDEWEB)

Levitt, Daniel G. [Los Alamos National Laboratory; Kwicklis, Edward M. [Los Alamos National Laboratory

2012-07-13

The outline of this presentation are: (1) Model Inputs - DEM, Precipitation, Air temp, Soil props, Surface geology, Vegetation; (2) Model Pre-processing - Runoff Routing and sinks, Slope and Azimuth, Soil Ksat reduction with slope (to mitigate bathtub ring), Soil-Bedrock Interface permeabilities; (3) Model Calibration - ET using PEST, Chloride mass balance data, Streamflow using PEST; (4) Model Validation - Streamflow data not used for calibration; (5) Uncertainty Analysis; and (6) Results. Conclusions are: (1) Average annual infiltration rates =11 to 18 mm/year for RM domain; (2) Average annual infiltration rates = 7 to 11 mm/year for SM domain; (3) ET = 70% of precipitation for both domains; (4) Runoff = 8-9% for RM; and 22-24% for SM - Apparently high average runoff is caused by the truncation of the lowerelevation portions of watersheds where much of the infiltration of runoff waters would otherwise occur; (5) Model results are calibrated to measured ET, CMB data, and streamflow observations; (6) Model results are validated using streamflow observations discovered after model calibration was complete; (7) Use of soil Ksat reduction with slope to mitigate bathtub ring was successful (based on calibration results); and (8) Soil-bedrock K{_}interface is innovative approach.

Forsmark site investigation. Bedrock geology - overview and excursion guide

Energy Technology Data Exchange (ETDEWEB)

Stephens, Michael B. (Geological Survey of Sweden, Uppsala (Sweden))

2010-09-15

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

Forsmark site investigation. Bedrock geology - overview and excursion guide

International Nuclear Information System (INIS)

Stephens, Michael B.

2010-09-01

Bearing in mind the significance of the bedrock data from the ground surface for the geological 3D modelling work, SKB decided to present excursion guides that serve in the demonstration of the bedrock geology at the ground surface in both the Forsmark (this guide) and Laxemar-Simpevarp areas. An excursion guide is also available for the Olkiluoto area in south-western Finland, which has been selected for the construction of a repository for the disposal of highly radioactive, spent nuclear fuel in Finland. The current excursion guide presents the bedrock geology and describes in detail the character of the bedrock at ten representative outcrops or outcrop areas at the ground surface in the site investigation area at Forsmark. All localities are located within or immediately adjacent to the proposed repository volume selected by SKB

Preliminary estimates of spatially distributed net infiltration and recharge for the Death Valley region, Nevada-California

International Nuclear Information System (INIS)

Hevesi, J.A.; Flint, A.L.; Flint, L.E.

2002-01-01

A three-dimensional ground-water flow model has been developed to evaluate the Death Valley regional flow system, which includes ground water beneath the Nevada Test Site. Estimates of spatially distributed net infiltration and recharge are needed to define upper boundary conditions. This study presents a preliminary application of a conceptual and numerical model of net infiltration. The model was developed in studies at Yucca Mountain, Nevada, which is located in the approximate center of the Death Valley ground-water flow system. The conceptual model describes the effects of precipitation, runoff, evapotranspiration, and redistribution of water in the shallow unsaturated zone on predicted rates of net infiltration; precipitation and soil depth are the two most significant variables. The conceptual model was tested using a preliminary numerical model based on energy- and water-balance calculations. Daily precipitation for 1980 through 1995, averaging 202 millimeters per year over the 39,556 square kilometers area of the ground-water flow model, was input to the numerical model to simulate net infiltration ranging from zero for a soil thickness greater than 6 meters to over 350 millimeters per year for thin soils at high elevations in the Spring Mountains overlying permeable bedrock. Estimated average net infiltration over the entire ground-water flow model domain is 7.8 millimeters per year. To evaluate the application of the net-infiltration model developed on a local scale at Yucca Mountain, to net-infiltration estimates representing the magnitude and distribution of recharge on a regional scale, the net-infiltration results were compared with recharge estimates obtained using empirical methods. Comparison of model results with previous estimates of basinwide recharge suggests that the net-infiltration estimates obtained using this model may overestimate recharge because of uncertainty in modeled precipitation, bedrock permeability, and soil properties for

Topographic and hydraulic controls over alluviation on a bedrock template

Science.gov (United States)

Milan, David; Heritage, George; Entwistle, Neil; Tooth, Stephen

2017-04-01

Bedrock-alluvial anastomosed channels found in dryland rivers are characterised by an over-wide channel cut into the host rock containing a network of interconnecting bedrock sub-channels separated by bedrock influenced interfluve areas. Whilst the channels remain largely free of sediment the interfluves display varying levels of alluviation ranging from bare rock, sand sheets and silt drapes through to consolidated bedrock core bars, islands and lateral deposits. Examination of the sedimentary units associated with the bedrock anastomosed reaches of the Sabie river in the Kruger National Park, South Africa reveal a repeating sequence of coarse sand / fine gravel grading through to silt representing successive flood related depositional units. Unit development in relation to the bedrock template was investigated using pre-flood aerial imagery of bedrock core bar locations and post flood LiDAR data of bedrock anastomosed sites stripped during the 2000 and 2012 extreme flood events. This revealed a propensity for bar development associated with bedrock hollows disconnected from the principal high-energy sub-channels. 2-D morpho-dynamic modelling was used to further investigate spatial patterns of deposition over the bedrock template. Although topographic lows displayed mid-range velocities during peak flow events, these are likely to be preferential routing areas, with sediments stalling in low energy areas on the falling limb of floods. It is also likely that vegetation development plays a fundamental role in the development of alluviated zones, through increasing strength of alluvial units and capturing new sediments. With these results in mind we present a conceptual model for the development of bedrock-core bars, the fundamental unit in bedrock-alluvial anastomosed channels.

Iowa Bedrock Geology

Data.gov (United States)

Iowa State University GIS Support and Research Facility — The bedrock geologic map portrays the current interpretation of the distribution of various bedrock stratigraphic units present at the bedrock surface. The bedrock...

A process to estimate net infiltration using a site-scale water-budget approach, Rainier Mesa, Nevada National Security Site, Nevada, 2002–05

Science.gov (United States)

Smith, David W.; Moreo, Michael T.; Garcia, C. Amanda; Halford, Keith J.; Fenelon, Joseph M.

2017-08-29

This report documents a process used to estimate net infiltration from precipitation, evapotranspiration (ET), and soil data acquired at two sites on Rainier Mesa. Rainier Mesa is a groundwater recharge area within the Nevada National Security Site where recharged water flows through bedrock fractures to a deep (450 meters) water table. The U.S. Geological Survey operated two ET stations on Rainier Mesa from 2002 to 2005 at sites characterized by pinyon-juniper and scrub-brush vegetative cover. Precipitation and ET data were corrected to remove measurement biases and gap-filled to develop continuous datasets. Net infiltration (percolation below the root zone) and changes in root-zone water storage were estimated using a monthly water-balance model.Site-scale water-budget results indicate that the heavily-fractured welded-tuff bedrock underlying thin (water source for vegetation during dry periods. Annual precipitation during the study period ranged from fourth lowest (182 millimeters [mm]) to second highest (708 mm) on record (record = 55 years). Annual ET exceeded precipitation during dry years, indicating that the fractured-bedrock reservoir capacity is sufficient to meet atmospheric-evaporative demands and to sustain vegetation through extended dry periods. Net infiltration (82 mm) was simulated during the wet year after the reservoir was rapidly filled to capacity. These results support previous conclusions that preferential fracture flow was induced, resulting in an episodic recharge pulse that was detected in nearby monitoring wells. The occurrence of net infiltration only during the wet year is consistent with detections of water-level rises in nearby monitoring wells that occur only following wet years.

Bedrock geology Forsmark. Modelling stage 2.3. Description of the bedrock geological map at the ground surface

Energy Technology Data Exchange (ETDEWEB)

Stephens, Michael B.; Bergman, Torbjoern (Geological Survey of Sweden, Uppsala (Sweden)); Isaksson, Hans (GeoVista AB, Luleaa (Sweden)); Petersson, Jesper (SwedPower AB, Stockholm (Sweden))

2008-12-15

A description of the bedrock geological map of the ground surface at the Forsmark site is presented here. This map is essentially a 2D model for the distribution of different types of rock unit on this surface. Besides showing the distribution of these rock units, the bedrock geological map also displays the distribution of some deformation zones that intersect the ground surface. It also presents information bearing on the position and form of outcrops, the location and projection of boreholes drilled during the site investigation programme, subordinate rock types, the occurrence of abandoned mines or exploration prospects, measurements of ductile structures in outcrops, inferred form lines, key minerals, and the occurrence of mylonite and cataclastic rock. Bedrock data from outcrops and excavations, airborne and ground magnetic data and information from the uppermost part of boreholes have all been used in the construction of the geological map. The description has also made use of complementary analytical data bearing on the composition and age of the rocks as well gamma-ray spectrometry and gravity data. Uncertainty in the position of the boundaries between rock units over the mapped area are addressed in a qualitative manner. Four model versions of the bedrock geological map have been delivered to SKB's GIS database (bedrock geological map, Forsmark, versions 1.1, 1.2, 2.2 and 2.3) at different times during the site investigation programme. The Forsmark area is situated along the coast of the Baltic Sea in northern Uppland, Sweden, in a region where the overall level of ductile strain in the bedrock is high. This high-strain region extends several tens of kilometres across the WNW-ENE to NW-SE strike of the rocks in this part of the Fennoscandian Shield. At Forsmark, the coastal region is composed partly of high-strain belts, which formed under amphibolite-facies metamorphic conditions, and partly of tectonic lenses, where the bedrock is also affected by

Bedrock geology Forsmark. Modelling stage 2.3. Description of the bedrock geological map at the ground surface

International Nuclear Information System (INIS)

Stephens, Michael B.; Bergman, Torbjoern; Isaksson, Hans; Petersson, Jesper

2008-12-01

A description of the bedrock geological map of the ground surface at the Forsmark site is presented here. This map is essentially a 2D model for the distribution of different types of rock unit on this surface. Besides showing the distribution of these rock units, the bedrock geological map also displays the distribution of some deformation zones that intersect the ground surface. It also presents information bearing on the position and form of outcrops, the location and projection of boreholes drilled during the site investigation programme, subordinate rock types, the occurrence of abandoned mines or exploration prospects, measurements of ductile structures in outcrops, inferred form lines, key minerals, and the occurrence of mylonite and cataclastic rock. Bedrock data from outcrops and excavations, airborne and ground magnetic data and information from the uppermost part of boreholes have all been used in the construction of the geological map. The description has also made use of complementary analytical data bearing on the composition and age of the rocks as well gamma-ray spectrometry and gravity data. Uncertainty in the position of the boundaries between rock units over the mapped area are addressed in a qualitative manner. Four model versions of the bedrock geological map have been delivered to SKB's GIS database (bedrock geological map, Forsmark, versions 1.1, 1.2, 2.2 and 2.3) at different times during the site investigation programme. The Forsmark area is situated along the coast of the Baltic Sea in northern Uppland, Sweden, in a region where the overall level of ductile strain in the bedrock is high. This high-strain region extends several tens of kilometres across the WNW-ENE to NW-SE strike of the rocks in this part of the Fennoscandian Shield. At Forsmark, the coastal region is composed partly of high-strain belts, which formed under amphibolite-facies metamorphic conditions, and partly of tectonic lenses, where the bedrock is also affected by

Bedrock model of the Veitsivaara area

International Nuclear Information System (INIS)

Saksa, P.; Kuivamaeki, A.; Kurimo, M.; Anttila, P.; Front, K.; Pitkaenen, P.; Korkealaakso, J.; Vaittinen, T.

1993-07-01

Site investigations were carried out at Veitsivaara, in 1987-1991 in accordance with an investigation programme for radioactive waste disposal drawn up by Teollisuuden Voima Oy (TVO). The site was modelled in terms of rock types, fracturing, fracture structures and geophysical conditions, the main focus of examination was on fracturing and associated hydraulic conductivity. The various properties of the bedrock structures were classified by means a three-dimensional model. The descriptions of the models were stored in a computer system for illustration purposes. The rock types at Veitsivaara are tonalite gneiss, Tuliniemet potassium granite, amphipolite, granite porphyry and metadiabase, the last two of which occur in dykes

Ground source energy in crystalline bedrock - increased energy extraction by using hydraulic fracturing in boreholes

Energy Technology Data Exchange (ETDEWEB)

Ramstad, Randi Kalstad

2004-11-01

energy extraction and a successful operation of ground source heat pump systems based on circulating groundwater. Results from the short-period circulation tests accomplished at Bryn and EAB show that the infiltration rate in the central borehole at Bryn (approximately 2500 litres/hour) was too low to obtain a satisfactory operation of the plant, while the infiltration rate at EAB (14000 litres/ hour) was sufficient to achieve profitability. Under the actual conditions, a reduction in the construction costs, i.e. the drilling costs, for a conventional ground source heat pump system with single U-collectors in vertical boreholes, of more than 50% were achieved for the pilot plant at EAB when the energy extraction from water is more than 105 MWh. The large difference in the infiltration rate between Bryn and EAB was probably related to: (1) Large initial differences in the borehole yield prior to hydraulic fracturing (<560 litres/hour at Bryn and >6300 litres/hour at EAB). Nodular limestone generally has high permeability, while compact sandstone rocks are expected to have low permeability. (2) hydraulic fracturing was most successful at EAB. (3) The higher rock stress level present at Bryn compared to EAB will increase the tendency to tighten the opened fractures, even the fractures with injected sand. (6) The FEFLOW-modelling of the pilot plant at Bryn and EAB emphasized the important relation between the available heat exchange area in the bedrock, the thermal conductivity of the bedrock, and the energy potential. (7) he increased borehole yields achieved by hydraulic fracturing in this study, and the improved, reliable and cost-effective hydraulic fracturing techniques in crystalline bedrock, will probably increase the interest for groundwater as a domestic water supply for small- to medium sized water works. (author)

Bedrock model of the Olkiluoto area

International Nuclear Information System (INIS)

Saksa, P.; Paananen, M.; Paulamaeki, S.; Anttila, P.; Front, K.; Pitkaenen, P.; Hassinen, P.; Ylinen, A.

1993-07-01

Site investigations were carried out at Olkiluoto (in Finland) in 1987-1992 in accordance with an investigation programme drawn up by Teollisuuden Voima Oy (TVO). The site was modelled in terms of rock types, fracturing, fracture structures and geohydrological conditions, the main focus of examination was on fracturing and associated hydraulic conductivity. The various properties of the bedrock structures were classified by means of a three-dimensional model. The descriptions of the models were gathered in a computer system for illustration and storage purposes. The rock types at Olkiluoto are migmatite, which may be divided into mica gneiss and veined gneiss, and also tonalite and coarse-grained migmatite granite (pegmatite). (64 refs., 65 figs.)

E-Area LLWF Vadose Zone Model: Probabilistic Model for Estimating Subsided-Area Infiltration Rates

Energy Technology Data Exchange (ETDEWEB)

Dyer, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-12-12

A probabilistic model employing a Monte Carlo sampling technique was developed in Python to generate statistical distributions of the upslope-intact-area to subsided-area ratio (Area_UAi/Area_SAi) for closure cap subsidence scenarios that differ in assumed percent subsidence and the total number of intact plus subsided compartments. The plan is to use this model as a component in the probabilistic system model for the E-Area Performance Assessment (PA), contributing uncertainty in infiltration estimates.

Bedrock geologic Map of the Central Block Area, Yucca Mountain, Nye County, Nevada

International Nuclear Information System (INIS)

W.C. Day; C. Potter; D. Sweetkind; R.P. Dickerson; C.A. San Juan

1998-01-01

Bedrock geologic maps form the foundation for investigations that characterize and assess the viability of the potential high-level radioactive waste repository at Yucca Mountain, Nevada. As such, this map focuses on the central block at Yucca Mountain, which contains the potential repository site. The central block is a structural block of Tertiary volcanic rocks bound on the west by the Solitario Canyon Fault, on the east by the Bow Ridge Fault, to the north by the northwest-striking Drill Hole Wash Fault, and on the south by Abandoned Wash. Earlier reconnaissance mapping by Lipman and McKay (1965) provided an overview of the structural setting of Yucca Mountain and formed the foundation for selecting Yucca Mountain as a site for further investigation. They delineated the main block-bounding faults and some of the intrablock faults and outlined the zoned compositional nature of the tuff units that underlie Yucca Mountain. Scott and Bonk (1984) provided a detailed reconnaissance geologic map of favorable area at Yucca Mountain in which to conduct further site-characterization studies. Of their many contributions, they presented a detailed stratigraphy for the volcanic units, defined several other block-bounding faults, and outlined numerous intrablock faults. This study was funded by the U.S. Department of Energy Yucca Mountain Project to provide a detailed (1:6,000-scale) bedrock geologic map for the area within and adjacent to the potential repository area at Yucca Mountain, Nye County, Nevada. Prior to this study, the 1:12,000-scale map of Scott and Bonk (1984) was the primary source of bedrock geologic data for the Yucca Mountain Project. However, targeted detailed mapping within the central block at Yucca Mountain revealed structural complexities along some of the intrablock faults that were not evident at 1:12,000 (Scott and Bonk, 1984). As a result, this study was undertaken to define the character and extent of the dominant structural features in the

Fuzzy logic-based assessment for mapping potential infiltration areas in low-gradient watersheds.

Science.gov (United States)

Quiroz Londoño, Orlando Mauricio; Romanelli, Asunción; Lima, María Lourdes; Massone, Héctor Enrique; Martínez, Daniel Emilio

2016-07-01

This paper gives an account of the design a logic-based approach for identifying potential infiltration areas in low-gradient watersheds based on remote sensing data. This methodological framework is applied in a sector of the Pampa Plain, Argentina, which has high level of agricultural activities and large demands for groundwater supplies. Potential infiltration sites are assessed as a function of two primary topics: hydrologic and soil conditions. This model shows the state of each evaluated subwatershed respecting to its potential contribution to infiltration mainly based on easily measurable and commonly used parameters: drainage density, geomorphologic units, soil media, land-cover, slope and aspect (slope orientation). Mapped outputs from the logic model displayed 42% very low-low, 16% moderate, 41% high-very high contribution to potential infiltration in the whole watershed. Subwatersheds in the upper and lower section were identified as areas with high to very high potential infiltration according to the following media features: low drainage density (drainage plain and, dunes and beaches. Copyright © 2016 Elsevier Ltd. All rights reserved.

The composition of the ground water in bedrock in the precambrian shield areas of Finland and other countries

International Nuclear Information System (INIS)

Hyyppae, J.

1986-11-01

The main properties of the composition of the ground water contained in the Precambrian bedrock of Finland are presented on the basis of the results of analyses of some 1750 water samples taken from bored wells and a few mines. They show that, with a few exceptions, the waters of bored wells are bicarbonate waters, in which the average total amount of dissolved substances diminishes according to their geographical location as one moves from the coastal areas toward estern and northern Finland. The influence of the mineral composition of the bedrock appears most distinctly in the rapakivi areas, where the average fluoride content of the ground water varies between 1.5 and 2.0 mg/l and is thus ten times the corresponding content prevailing in areas characterized by other types of rocks. Ground waters containing from 439 to 18.000 mg/l of chloride have also been met with in Finnish bedrock and the location of the sampling site of 38 samples is given together with the general nature of their chemical composition as well as the results of the determinations of the stable (δ ''2H, δ ''1''8O, δ ''3''4S, δ ''1''3C) and radioactive (''3H, ''1''4C) isotopes of a number of samples. The saline waters are mostly located in the region covered 6000-7500 years ago by the Littorina Sea. On the other hand, the isotopic composition of many saline waters corresponds to that of rainwater fallen during climatic conditions colder than the present. The most saline waters have been met with deep down in mines and deep boreholes, also, for example, far from the region covered by the Littorina Sea. The saline waters contained in Finnish bedrock usually release gas, which in some cases consists mainly of nitrogen but in some places includes significant amounts of methane. In addition, helium is one of the constituents

Estimations of durability of fracture mineral buffers in the Olkiluoto bedrock

International Nuclear Information System (INIS)

Luukkonen, A.

2006-12-01

This study attempts to make scenarios for the geochemical effects that the underground excavations in the Olkiluoto bedrock have on naturally occurring fracture mineral buffers. The excavations of underground research facilities and final repository galleries probably cause steep hydraulic gradients in some bedrock fractures. These gradients likely draw surficial waters within the fracture network and activate weathering processes deeper in rock fractures than in the natural undisturbed conditions. The present studies concentrate on the meteoric infiltration in a single rock fracture, and on the selected set of minerals believed to be significant buffers against pH/redox variations in groundwater. The modelling considers the possibility that the infiltrating meteoric water is soil water rich in dissolved inorganic carbon. Calcite, pyrite, quartz, amorphous silica, cordierite, hornblende, albite, K-feldspar, kaolinite, and illite are taken into account as reacting minerals. Simulations are done by varying the flow rate of water from 1 L/h to 100 L/h. The effects of mineral reactions onto porosity and permeability values are monitored as well. In the present study, however, the changes in physical properties of the fracture channel do not affect the flow rate of water. Furthermore, calculations also describe how cation exchange affects the studied fracture channel system. The simulations coupling the hydraulic flow and water-rock interaction were done with TOUGHREACT V1.0 code and with the EQ3/6-database implemented in the code. In part, the simulations were evaluation of the code capabilities, and verification of results to earlier PHREEQC-2 simulation results. The calculation results confirm the assumption that principal buffer against pH changes is calcite. All silicate reactions, with considered reactive surface areas, are by comparison of marginal importance. The only redox buffer in the calculations is pyrite, and consequently significant amounts of oxygen runs

Conceptual Modeling Framework for E-Area PA HELP Infiltration Model Simulations

Energy Technology Data Exchange (ETDEWEB)

Dyer, J. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-11-30

A conceptual modeling framework based on the proposed E-Area Low-Level Waste Facility (LLWF) closure cap design is presented for conducting Hydrologic Evaluation of Landfill Performance (HELP) model simulations of intact and subsided cap infiltration scenarios for the next E-Area Performance Assessment (PA).

Bedrock model of the Kivetty area

International Nuclear Information System (INIS)

Saksa, P.; Paulamaeki, S.; Paananen, M.; Anttila, P.; Front, K.; Pitkaenen, P.; Korkealaakso, J.; Okko, O.

1993-07-01

Preliminary site investigations were carried out at Kivetty (in Finland), in 1987-1992 in accordance with the investigation programme drawn up by Teollisuuden Voima Oy (TVO). The site was modelled in terms of rock type, fracturing, fracture structures and geohydrological conditions, with the main emphasis being placed on fracturing and associated hydraulic conductivity. The various properties of the bedrock structures were classified in relation to a three-dimensional model. The descriptions of the models were stored in a computer system for the purpose of illustration. The principal rock types encountered at the Kivetty site are porphyritic granodiorite and porphyritic granite, in addition to which even-grained granite and granodiorite, gabbro, and small felsic and mafic veins occur. The rocks have undergone two distinct phases of deformation. (41 refs., 50 figs.)

Mapping Bedrock Topography using Electromagnetic Profiling ...

African Journals Online (AJOL)

Mapping Bedrock Topography using Electromagnetic Profiling. ... will be constructed The area under study is within the Abakaliki Shales Geologic Formation. ... micaceous sandstone; micaceous siltstone, sandy shales and shelly limestone.

The amount of glacial erosion of the bedrock

International Nuclear Information System (INIS)

Paasse, Tore

2004-11-01

The purpose of this study is to estimate an upper bound for the average erosion of fresh bedrock that can reasonably be expected during a glacial period or a single glaciation. The study is based on the assumption that classic sediments, formed by Scandinavian ice erosion during the Quaternary period, still exist within the formerly glaciated area or its periphery. The volume of these sediments thus constitutes the maximum average glacial erosion of bedrock within this area. This volume is calculated by estimating the thickness of the minerogenic Quaternary from well data in Sweden and Denmark and from seismic measurements in adjacent sea areas. The average thickness of the Quaternary deposits and other reogolith in the investigated area was estimated to 16 m. Assuming that the whole volume is the result of glacial erosion of fresh bedrock this corresponds to 12 m depth. However, a great part of the sediments may consist of glacially redistributed Tertiary regolith. As the amount of Tertiary regolith is uncertain the estimated maximum average glacial erosion rate in fresh bedrock is uncertain, and assuming that the total sediment volume is the result of glacial erosion leads to an overestimation of the glacial erosion depth. Considering this, the average glacial erosion during a full glacial period has been estimated to between 0.2 m and 4 m. If the extremes in the made assumptions are excluded the glacial erosion during a glacial cycle can be estimated to about 1 m

The amount of glacial erosion of the bedrock

Energy Technology Data Exchange (ETDEWEB)

Paasse, Tore [Geological Survey of Sweden, Uppsala (Sweden)

2004-11-01

The purpose of this study is to estimate an upper bound for the average erosion of fresh bedrock that can reasonably be expected during a glacial period or a single glaciation. The study is based on the assumption that classic sediments, formed by Scandinavian ice erosion during the Quaternary period, still exist within the formerly glaciated area or its periphery. The volume of these sediments thus constitutes the maximum average glacial erosion of bedrock within this area. This volume is calculated by estimating the thickness of the minerogenic Quaternary from well data in Sweden and Denmark and from seismic measurements in adjacent sea areas. The average thickness of the Quaternary deposits and other reogolith in the investigated area was estimated to 16 m. Assuming that the whole volume is the result of glacial erosion of fresh bedrock this corresponds to 12 m depth. However, a great part of the sediments may consist of glacially redistributed Tertiary regolith. As the amount of Tertiary regolith is uncertain the estimated maximum average glacial erosion rate in fresh bedrock is uncertain, and assuming that the total sediment volume is the result of glacial erosion leads to an overestimation of the glacial erosion depth. Considering this, the average glacial erosion during a full glacial period has been estimated to between 0.2 m and 4 m. If the extremes in the made assumptions are excluded the glacial erosion during a glacial cycle can be estimated to about 1 m.

Review of DOE's proposal for Crystalline bedrock disposal of radioactive waste, north-central area

International Nuclear Information System (INIS)

Green, J.C.

1986-01-01

The DOE's Region-to-Area Screening Methodology for the Crystalline Repository Project (DOE/CH-1), the Final North-Central Region Geologic Characterization Report (DOE/CH-8(1)), and the Draft Area Recommendation Report for the Crystalline Repository Project (DOE/CH-15), with the associated maps, were reviewed. The review has focused on all general information regarding geologic topics and all site-specific data for DOE sites NC-10 and NC-3. This report contains two parts: (1) a point-by-point critique of perceived errors, omissions, or other shortcomings in each of the three documents; and (2) a discussion of the feasibility of crystalline bedrock as a suitable host medium for high-level radioactive waste

Controls on the variability of net infiltration to desert sandstone

Science.gov (United States)

Heilweil, Victor M.; McKinney, Tim S.; Zhdanov, Michael S.; Watt, Dennis E.

2007-01-01

As populations grow in arid climates and desert bedrock aquifers are increasingly targeted for future development, understanding and quantifying the spatial variability of net infiltration becomes critically important for accurately inventorying water resources and mapping contamination vulnerability. This paper presents a conceptual model of net infiltration to desert sandstone and then develops an empirical equation for its spatial quantification at the watershed scale using linear least squares inversion methods for evaluating controlling parameters (independent variables) based on estimated net infiltration rates (dependent variables). Net infiltration rates used for this regression analysis were calculated from environmental tracers in boreholes and more than 3000 linear meters of vadose zone excavations in an upland basin in southwestern Utah underlain by Navajo sandstone. Soil coarseness, distance to upgradient outcrop, and topographic slope were shown to be the primary physical parameters controlling the spatial variability of net infiltration. Although the method should be transferable to other desert sandstone settings for determining the relative spatial distribution of net infiltration, further study is needed to evaluate the effects of other potential parameters such as slope aspect, outcrop parameters, and climate on absolute net infiltration rates.

Infiltration control for low-level radioactive solid waste disposal areas: an assessment

International Nuclear Information System (INIS)

Arora, H.S.

1980-11-01

The primary mode of radionuclide transport from shallow land-disposal sites for low-level wastes can be traced to infiltration of precipitation. This report examines the factors that affect surface water entry and movement in the ground and assesses available infiltration-control technology for solid-waste-disposal sites in the humid eastern portion of the United States. A survey of the literature suggests that a variety of flexible and rigid liner systems are available as barriers for the stored waste and would be effective in preventing water infiltration. Installation of near-surface seals of bentonite clay admixed with dispersive chemicals seem to offer the required durability and low permeability at a reasonable cost. The infiltration rate in a bentonite-sealed area may be further retarded by the application of dispersive chemicals that can be easily admixed with the surface soil. Because the effectiveness of a dispersive chemical for infiltration reduction is influenced by the physico-chemical properties of the soil, appropriate laboratory tests should be conducted prior to field application

A study on groundwater infiltration in the Horonobe area, northern Hokkaido, Japan

International Nuclear Information System (INIS)

Yokota, Hideharu; Yamamoto, Yoichi; Maekawa, Keisuke; Hara, Minoru

2011-01-01

In the Horonobe area of northern Hokkaido, the Japan Atomic Energy Agency has been carrying out various hydrological observations to estimate the recharge rate. Subsurface earth temperature and soil moisture content have been observed at HGW-1 site (GL-0.7m to GL-2.3m, since 2005) and Hokushin Meteorological Station (GL-0.1m to GL-1.1m, since 2008). The results have revealed groundwater infiltration and recharge occurring throughout year, the shallow groundwater-infiltration velocity depending on the depth and the position of the Zero Flux Plane. For the estimation of boundary conditions in groundwater flow simulation, in this study, the shallow groundwater-flow system has been examined qualitatively on the basis of the variation of the subsurface earth temperature and the soil moisture content. In the future, it is necessary to quantitatively assess the shallow groundwater infiltration and recharge rate, the intermediate runoff, and the evapotranspiration based on the observed data of the weighing lysimeter, and the other measurement stations in the area. (author)

Detections of MTBE in surficial and bedrock aquifers in New England

International Nuclear Information System (INIS)

Grady, S.J.

1995-01-01

The gasoline additive methyl tert-butyl ether (MTBE) was detected in 24% of water samples collected from surficial and bedrock aquifers in areas of New England. MTBE was the most frequently detected volatile organic compound among the 60 volatile chemicals analyzed and was present in 33 of 133 wells sampled from July 1993 through September 1995. The median MTBE concentration measured in ground-water samples was 0.45 microgram per liter and concentrations ranged from 0.2 to 5.8 microgram per liter. The network of wells sampled for MTBE consisted of 103 monitoring wells screened in surficial sand-and-gravel aquifers and 30 domestic-supply wells in fractured crystalline bedrock aquifers. Seventy-seven percent of all MTBE detections were from 26 shallow monitoring wells screened in surficial aquifers. MTBE was detected in42% of monitoring wells in urban areas. In agricultural areas, MTBE was detected i 8% (2 of 24) of wells and was not detected in undeveloped areas. Sixty-two percent of the MTBE detections in surficial aquifers were from wells within 0.25 mile of gasoline stations or underground gasoline storage tanks; all but one of these wells were in Connecticut and Massachusetts, where reformulated gasoline is used. MTBE was detected in 23% of deep domestic-supply wells that tapped fractured bedrock aquifers. MTBE was detected in bedrock wells only in Connecticut and Massachusetts; land use near the wells was suburban to rural, and none of the sampled bedrock wells were within 0.25 mile of a gasoline station

Identification Of Rippability And Bedrock Depth Using Seismic Refraction

Science.gov (United States)

Ismail, Nur Azwin; Saad, Rosli; Nawawi, M. N. M.; Muztaza, Nordiana Mohd; El Hidayah Ismail, Noer; Mohamad, Edy Tonizam

2010-12-01

Spatial variability of the bedrock with reference to the ground surface is vital for many applications in geotechnical engineering to decide the type of foundation of a structure. A study was done within the development area of Mutiara Damansara utilising the seismic refraction method using ABEM MK8 24 channel seismograph. The geological features of the subsurface were investigated and velocities, depth to the underlying layers were determined. The seismic velocities were correlated with rippability characteristics and borehole records. Seismic sections generally show a three layer case. The first layer with velocity 400-600 m/s predominantly consists of soil mix with gravel. The second layer with velocity 1600-2000 m/s is suggested to be saturated and weathered area. Both layers forms an overburden and generally rippable. The third layer represents granite bedrock with average depth and velocity 10-30 m and >3000 m/s respectively and it is non-rippable. Steep slope on the bedrock are probably the results of shear zones.

Identification Of Rippability And Bedrock Depth Using Seismic Refraction

International Nuclear Information System (INIS)

Ismail, Nur Azwin; Saad, Rosli; Nawawi, M. N. M; Muztaza, Nordiana Mohd; El Hidayah Ismail, Noer; Mohamad, Edy Tonizam

2010-01-01

Spatial variability of the bedrock with reference to the ground surface is vital for many applications in geotechnical engineering to decide the type of foundation of a structure. A study was done within the development area of Mutiara Damansara utilising the seismic refraction method using ABEM MK8 24 channel seismograph. The geological features of the subsurface were investigated and velocities, depth to the underlying layers were determined. The seismic velocities were correlated with rippability characteristics and borehole records. Seismic sections generally show a three layer case. The first layer with velocity 400-600 m/s predominantly consists of soil mix with gravel. The second layer with velocity 1600-2000 m/s is suggested to be saturated and weathered area. Both layers forms an overburden and generally rippable. The third layer represents granite bedrock with average depth and velocity 10-30 m and >3000 m/s respectively and it is non-rippable. Steep slope on the bedrock are probably the results of shear zones.

SMOS brightness data indicate ice thickness hence bedrock topography in east antarctica

DEFF Research Database (Denmark)

Skou, Niels; Kristensen, Steen Savstrup

2017-01-01

In order to evaluate a potential calibration target for spaceborne L-band radiometer systems, a 350 × 350 km area near the Concordia station on the East Antarctica plateau was mapped by an airborne L-band radiometer. Unexpectedly, the area showed significant brightness temperature spatial...... variations, well correlated with bedrock topography, hence ice thickness. Using SMOS data over a poorly known part of Antarctica, ice thickness in this area has been assessed, and an existing bedrock map has been improved....

Differentiation between vasogenic-edema versus tumor-infiltrative area in patients with glioblastoma during bevacizumab therapy: A longitudinal MRI study

Energy Technology Data Exchange (ETDEWEB)

Artzi, Moran, E-mail: artzimy@gmail.com [Functional Brain Center, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Sackler Faculty of Medicine, Tel Aviv University, Tel Aviv (Israel); Bokstein, Felix, E-mail: felixb@tlvmc.gov.il [Neuro-Oncology Service, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Blumenthal, Deborah T., E-mail: deborahblumenthal@gmail.com [Neuro-Oncology Service, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Aizenstein, Orna, E-mail: Ornaaizenstein@gmail.com [Functional Brain Center, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Liberman, Gilad, E-mail: giladliberman@gmail.com [Functional Brain Center, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Gonda Multidisciplinary Brain Research Center, Bar Ilan University, Ramat Gan (Israel); Corn, Benjamin W., E-mail: bencorn@tlvmc.gov.il [Functional Brain Center, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Institute of Radiotherapy, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Ben Bashat, Dafna, E-mail: dafnab@tlvmc.gov.il [Functional Brain Center, Tel Aviv Sourasky Medical Center, Tel Aviv (Israel); Sackler Faculty of Medicine, Tel Aviv University, Tel Aviv (Israel); Sagol School of Neuroscience, Tel Aviv University, Tel Aviv (Israel)

2014-07-15

Background: Treatment with bevacizumab is associated with substantial radiologic response in patients with glioblastoma (GB). However, following this initial response, changes in T{sub 2}-weighted MRI signal may develop, suggesting an infiltrative pattern of tumor progression. The aim of this study was to differentiate between vasogenic-edema versus tumor-infiltrative area in GB patients. Methods and materials: Fourteen patients with GB were longitudinally scanned, before and during intravenous bevacizumab therapy (5/10 mg/kg every 2-weeks). A total of 40 MR scans including conventional, diffusion, dynamic susceptibility contrast, dynamic contrast enhancement imaging, and MR-spectroscopy (MRS) were analyzed. Classification of non-enhancing fluid-attenuation-inversion-recovery (FLAIR) area was performed based on mean diffusivity, cerebral blood volume and flow maps, and further characterized using multiple MRI parameters. Results: The non-enhancing FLAIR lesion area was classified into: vasogenic-edema, characterized by reduced perfusion and increased FLAIR values; or tumor-infiltrative area, characterized by increased perfusion. Tumor-infiltrative area demonstrated a higher malignant pattern on MRS compared to areas of vasogenic-edema. Substantial reductions of the enhanced T{sub 1}-weighted (58 ± 10%) and hyperintense FLAIR (53 ± 9%) lesion volumes were detected mainly during the first weeks of therapy, with a shift to an infiltrative pattern of tumor progression thereafter, as detected by an increase in tumor-infiltrative area in the majority of patients, which correlated with progression-free survival (week 8: r = −0.86, p = 0.003, week 16: r = −0.99, p = 0.001). Conclusion: Characterization of non-enhancing hyperintense FLAIR lesion area in GB patients can provide an MR-based biomarker, indicating a shift to an infiltrative progression pattern, and may improve therapy response assessment in patients following bevacizumab therapy.

Forsmark Bedrock mapping. Stage 1 (2002) - Outcrop data including fracture data

International Nuclear Information System (INIS)

Stephens, M.B.; Bergman, T.; Andersson, J.; Hermansson, T.; Wahlgren, C.H.; Albrecht, L.; Mikko, H.

2003-02-01

Infra-red aerial photographs over the study area, taken at a height of 2700 m, were interpreted in order to locate either the position of outcrops where the bedrock is exposed at the Earth's surface or sites where the bedrock lies beneath a thin (< 50 cm) cover of Quaternary deposits. These data were critical for the planning and execution of the field activities. It was aimed to map all the outcrops in the mainland part of the study area during stage 1 of the project. These data will be integrated with both bedrock analytical data and the interpretations obtained from the study of airborne geophysical data in order to produce a bedrock map over the study area. In order to gain some information on the regional variation in the frequency and orientation of fractures over the candidate area, a documentation of the position and strike and dip of fractures longer than 100 cm was carried out at 44 outcrops. This work will also help in the selection of outcrops where detailed fracture analysis will be carried out during a later stage of the site investigation programme. Field work associated with stage 1 of the project initiated in the candidate area during June 2002. Field activities then continued in the coastal area to the northeast, in the area north of 6700000 N to the northwest of the candidate area and in the inland area to the southwest. Field activities ceased during September 2002. Both descriptive and numerical data from the 1054 observation points have been included in an outcrop database. Primarily on account of the complexity of the outcrops visited and, as a consequence, the longer time required for the field activities, a large part of the area south of road 76 was not mapped during 2002

Forsmark Bedrock mapping. Stage 1 (2002) - Outcrop data including fracture data

Energy Technology Data Exchange (ETDEWEB)

Stephens, M.B.; Bergman, T.; Andersson, J.; Hermansson, T.; Wahlgren, C.H.; Albrecht, L.; Mikko, H. [Geological Survey of Sweden, Uppsala (Sweden)

2003-02-01

Infra-red aerial photographs over the study area, taken at a height of 2700 m, were interpreted in order to locate either the position of outcrops where the bedrock is exposed at the Earth's surface or sites where the bedrock lies beneath a thin (< 50 cm) cover of Quaternary deposits. These data were critical for the planning and execution of the field activities. It was aimed to map all the outcrops in the mainland part of the study area during stage 1 of the project. These data will be integrated with both bedrock analytical data and the interpretations obtained from the study of airborne geophysical data in order to produce a bedrock map over the study area. In order to gain some information on the regional variation in the frequency and orientation of fractures over the candidate area, a documentation of the position and strike and dip of fractures longer than 100 cm was carried out at 44 outcrops. This work will also help in the selection of outcrops where detailed fracture analysis will be carried out during a later stage of the site investigation programme. Field work associated with stage 1 of the project initiated in the candidate area during June 2002. Field activities then continued in the coastal area to the northeast, in the area north of 6700000 N to the northwest of the candidate area and in the inland area to the southwest. Field activities ceased during September 2002. Both descriptive and numerical data from the 1054 observation points have been included in an outcrop database. Primarily on account of the complexity of the outcrops visited and, as a consequence, the longer time required for the field activities, a large part of the area south of road 76 was not mapped during 2002.

Use of radon-222 as tracer to estimate groundwater infiltration velocity in a river bank area

International Nuclear Information System (INIS)

Trinh Van Giap

2003-01-01

Naturally occurring isotope Rn-222 has been used as a natural tracer to determine the residence time of groundwater infiltrated from river into an aquifer in a riverbank area. The applied method is based on the increasing radon concentration in infiltrating water during it passes through the riverbank and reaches an equilibrium value. Solid-state nuclear track detector technique is used to measure directly radon concentration in water of a well. In order to confirm the relationship between radon concentration and it's residence time, a model was constructed in the laboratory. Experiment carried out in Nam Dinh are showed that mean infiltrating velocity of groundwater in the studied area as high as 5.1 m/day. (author)

Spatial pattern of groundwater arsenic occurrence and association with bedrock geology in greater augusta, maine

Science.gov (United States)

Yang, Q.; Jung, H.B.; Culbertson, C.W.; Marvinney, R.G.; Loiselle, M.C.; Locke, D.B.; Cheek, H.; Thibodeau, H.; Zheng, Yen

2009-01-01

In New England, groundwater arsenic occurrence has been linked to bedrock geology on regional scales. To ascertain and quantify this linkage at intermediate (100-101 km) scales, 790 groundwater samples from fractured bedrock aquifers in the greater Augusta, Maine area are analyzed, and 31% of the sampled wells have arsenic concentrations >10 ??g/L. The probability of [As] exceeding 10 ??g/L mapped by indicator kriging is highest in Silurian pelite-sandstone and pelite-limestone units (???40%). This probability differs significantly (p bedrock map. Thus, bedrock geology is associated with arsenic occurrence in fractured bedrock aquifers of the study area at intermediate scales relevant to water resources planning. The arsenic exceedance rate for each rock unit is considered robust because low, medium, and high arsenic occurrences in four cluster areas (3-20 km2) with a low sampling density of 1-6 wells per km2 are comparable to those with a greater density of 5-42 wells per km2. About 12,000 people (21% of the population) in the greater Augusta area (???1135 km2) are at risk of exposure to >10 ??g/L arsenic in groundwater. ?? 2009 American Chemical Society.

Flow in bedrock canyons.

Science.gov (United States)

Venditti, Jeremy G; Rennie, Colin D; Bomhof, James; Bradley, Ryan W; Little, Malcolm; Church, Michael

2014-09-25

Bedrock erosion in rivers sets the pace of landscape evolution, influences the evolution of orogens and determines the size, shape and relief of mountains. A variety of models link fluid flow and sediment transport processes to bedrock incision in canyons. The model components that represent sediment transport processes are increasingly well developed. In contrast, the model components being used to represent fluid flow are largely untested because there are no observations of the flow structure in bedrock canyons. Here we present a 524-kilometre, continuous centreline, acoustic Doppler current profiler survey of the Fraser Canyon in western Canada, which includes 42 individual bedrock canyons. Our observations of three-dimensional flow structure reveal that, as water enters the canyons, a high-velocity core follows the bed surface, causing a velocity inversion (high velocities near the bed and low velocities at the surface). The plunging water then upwells along the canyon walls, resulting in counter-rotating, along-stream coherent flow structures that diverge near the bed. The resulting flow structure promotes deep scour in the bedrock channel floor and undercutting of the canyon walls. This provides a mechanism for channel widening and ensures that the base of the walls is swept clear of the debris that is often deposited there, keeping the walls nearly vertical. These observations reveal that the flow structure in bedrock canyons is more complex than assumed in the models presently used. Fluid flow models that capture the essence of the three-dimensional flow field, using simple phenomenological rules that are computationally tractable, are required to capture the dynamic coupling between flow, bedrock erosion and solid-Earth dynamics.

Effects of bedrock type on the indoor radon concentrations at the office buildings in Gyeongju, Korea

Directory of Open Access Journals (Sweden)

Park Hee Chan

2011-01-01

Full Text Available This study measured the indoor radon concentrations at 23 administrative office buildings in Gyeongju, Korea, which consists of 23 administrative districts. Using the Korean geological information system, the type of bedrock under the administrative office buildings was identified and classified in 3 major types: granite, sedimentary rock, and sedimentary rock-based fault. The changes in the indoor concentrations at the 23 administrative office buildings were analyzed according to the type of bedrock. As a result, the radon concentration in the areas with the granite bedrock was generally higher than that in the region of two other types of bedrock. In addition, the radon concentration was evaluated according to surface area and construction timing of the building. The indoor radon concentration generally increased with decreasing surface area of the building, particularly in granite distributed areas. For a building aged more than 15 years, the radon concentration in the building in the granite area was much higher. For the building aged 1 or 2 years, the radon concentration was high regardless of the type of the bedrock due to radon emanation from the building material, such as concrete.

Design of Infiltration Well in Wetlands Area that Suitable for Giving Maximum Groundwater Recharge

Directory of Open Access Journals (Sweden)

Irfan Prasetia

2016-02-01

Full Text Available Growth in residential, industrial, and office  area,are significantly occurred in all city in Indonesia. Unfortunately, this is also caused more land that being covered by pavement and concrete in the cities. Realized or not it will disturb the availability of the groundwater and also lead to flooding in the rainy season. One of the effective solutions to solve this problem is by making sufficient numbers of infiltration well in the city, especially in the residential area. This research was conducted to analyze the ideal design of the infiltration well in the residential area. The design was made according to the equation by Sunjoto, which also refers to Indonesia standard (SNI No: 03- 2453-2002. The results show that the ideal dimension for the infiltration well is to use the radius of the well (R of 1.25 m. With the R of 1.25 will give a significant recharge to the groundwater as much as ≈ 2.400 liter. It is expected that this research encourage a development in the urban drainage systems which will consider the environment and the groundwater reservation for the balance of our ecosystem.

Forested infiltration areas (FIA; principles, experiences, perspectives

Directory of Open Access Journals (Sweden)

G. Mezzalira

2014-09-01

Full Text Available This paper illustrates the origin and the main features of a Managed Aquifer Recharge (MAR measure known as Forested Infiltration Area (FIA, conceived by Veneto Agricoltura in 2007 and currently implemented at 7 pilot sites over the Vicenza Upper Plain in the Veneto region, with the financial and technical support of several public and private partners. In particular the outputs of the first recharge season (2013-2014 of two demonstrative FIA are presented and discussed (plants realized in 2013 by Consorzio di Bonifica Brenta within the framework of the Life Project AQUOR. The main peculiarities of the FIA measures are the multifunctionality guaranteed by the integration of hydraulic and biologic aspects, the high environmental compatibility and the friendly design and management.

Propagation characteristics of bedrock waves traveling from pre-Tertiary basement to engineering bedrock

Science.gov (United States)

Kinoshita, S.

2007-11-01

This study uses borehole array recordings to measure the propagation characteristics of bedrock waves traveling from pre-Tertiary basement (seismic bedrock) to engineering bedrock with an S-wave velocity of approximately 0.5-0.8 km/s. To avoid the destructive interference of surface-reflected down-going waves and incidence waves in seismic and engineering bedrock, borehole data recorded at sufficient depth levels are used in this study. This is the most important aspect of the fundamental basis of this study. The propagation characteristics, i.e., the transfer function, of bedrock motions for S-waves are well represented by a Butterworth-type low-pass filter model with a high corner frequency in excess of 15 Hz and a low decay rate of -3 power of frequency. The use of such a filter model is based on the concise representation of the transfer function from an engineering viewpoint. Simple one-dimensional ray theory with a plane wave approximation explains the characteristics of the model filter at low frequencies of less than approximately 5 Hz; however, one-dimensional ray theory with a plane wave approximation at high frequencies in excess of 5 Hz requires the unusual frequency characteristics of Q_S-1(f), which increases with increasing frequency, to explain the frequency characteristics of the model filter. These facts imply that the filter gain can be determined using the impedance ratio of seismic bedrock to engineering bedrock and the attenuation characteristics of the intervening media at low frequencies less than 5 Hz. However, the cutoff frequency and decay rate of the filter must be determined from observational data.

Predicted infiltration for sodic/saline soils from reclaimed coastal areas: sensitivity to model parameters.

Science.gov (United States)

Liu, Dongdong; She, Dongli; Yu, Shuang'en; Shao, Guangcheng; Chen, Dan

2014-01-01

This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline) and 1960 (Soil B, nonsaline) were used, with bulk densities of 1.4 or 1.5 g/cm(3). A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ₀ was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils.

Predicted Infiltration for Sodic/Saline Soils from Reclaimed Coastal Areas: Sensitivity to Model Parameters

Directory of Open Access Journals (Sweden)

Dongdong Liu

2014-01-01

Full Text Available This study was conducted to assess the influences of soil surface conditions and initial soil water content on water movement in unsaturated sodic soils of reclaimed coastal areas. Data was collected from column experiments in which two soils from a Chinese coastal area reclaimed in 2007 (Soil A, saline and 1960 (Soil B, nonsaline were used, with bulk densities of 1.4 or 1.5 g/cm3. A 1D-infiltration model was created using a finite difference method and its sensitivity to hydraulic related parameters was tested. The model well simulated the measured data. The results revealed that soil compaction notably affected the water retention of both soils. Model simulations showed that increasing the ponded water depth had little effect on the infiltration process, since the increases in cumulative infiltration and wetting front advancement rate were small. However, the wetting front advancement rate increased and the cumulative infiltration decreased to a greater extent when θ0 was increased. Soil physical quality was described better by the S parameter than by the saturated hydraulic conductivity since the latter was also affected by the physical chemical effects on clay swelling occurring in the presence of different levels of electrolytes in the soil solutions of the two soils.

Eskers and bedrock gorges (tunnel valleys in the Pakasaivo area, western Finnish Lapland

Directory of Open Access Journals (Sweden)

Peter Johansson

2003-01-01

Full Text Available Studies of the deglaciation of the last Scandinavian Ice Sheet, including the behavior of the ice sheet and meltwater activity, were conducted in the vicinity of the Pakasaivo canyon lake, located in western Finnish Lapland. Pakasaivo itself, a circular basin up to 100 m deep, was formed in the broken bedrock by glacial erosion and meltwater streams. It was originally related to a former subglacial meltwater system, including the deep Keinokursu gorge. Both this gorge and the Pakasaivo canyon lake were formed subglacially duringan early stage of deglaciation. It was characterized by intense meltwater erosion, which in Pakasaivo also seems to have generated a strong whirl. Steep-crested esker ridges were subsequently deposited; subaerial meltwater activity then followed. Finally the meltwaterwas discharged from the ice-dammed lake north of the area and passed through the Pakasaivo canyon to the ice-free areas. This caused additional intense erosion of the canyon floor and walls, and the deep circular basin is highly similar to a plunge pool formed at the base of a cataract.

Abiotic controls of emergent macrophyte density in a bedrock channel - The Cahaba River, AL (USA)

Science.gov (United States)

Vaughn, Ryan S.; Davis, Lisa

2015-10-01

Research examining bedrock channels is growing. Despite this, biotic-abiotic interactions remain a topic mostly addressed in alluvial systems. This research identified hydrogeomorphic factors operating at the patch-scale (100-102 m) in bedrock shoals of the Cahaba River (AL) that help determine the distribution of the emergent aquatic macrophyte, Justicia americana. Macrophyte patch density (number of stems/m2) and percent bedrock void surface area (rock surface area/m2 occupied by joints, fractures, and potholes) were measured (n = 24 within two bedrock shoals) using stem counts and underwater photography, respectively. One-dimensional hydrologic modeling (HEC-RAS 4.1.0) was completed for a section within a shoal to examine velocity and channel depth as controlling variables for macrophyte patch density. Results from binary logistic regression analysis identified depth and velocity as good predictors of the presence or absence of Justicia americana within shoal structures (depth p = 0.001, velocity p = 0.007), which is a similar finding to previous research conducted in alluvial systems. Correlation analysis between bedrock surface void area and stem density demonstrated a statistically significant positive correlation (r = 0.665, p = 0.01), elucidating a link between abiotic-biotic processes that may well be unique to bedrock channels. These results suggest that the amount of void space present in bedrock surfaces, in addition to localized depth and velocity, helps control macrophyte patch density in bedrock shoal complexes. The utility of geomorphology in explaining patch-scale habitat heterogeneity in this study highlights geomorphology's potential to help understand macrophyte habitat heterogeneity at the reach scale, while also demonstrating its promise for mapping and understanding habitat heterogeneity at the system scale.

Mapping the global depth to bedrock for land surface modelling

Science.gov (United States)

Shangguan, W.; Hengl, T.; Yuan, H.; Dai, Y. J.; Zhang, S.

2017-12-01

Depth to bedrock serves as the lower boundary of land surface models, which controls hydrologic and biogeochemical processes. This paper presents a framework for global estimation of Depth to bedrock (DTB). Observations were extracted from a global compilation of soil profile data (ca. 130,000 locations) and borehole data (ca. 1.6 million locations). Additional pseudo-observations generated by expert knowledge were added to fill in large sampling gaps. The model training points were then overlaid on a stack of 155 covariates including DEM-based hydrological and morphological derivatives, lithologic units, MODIS surfacee reflectance bands and vegetation indices derived from the MODIS land products. Global spatial prediction models were developed using random forests and Gradient Boosting Tree algorithms. The final predictions were generated at the spatial resolution of 250m as an ensemble prediction of the two independently fitted models. The 10-fold cross-validation shows that the models explain 59% for absolute DTB and 34% for censored DTB (depths deep than 200 cm are predicted as 200 cm). The model for occurrence of R horizon (bedrock) within 200 cm does a good job. Visual comparisons of predictions in the study areas where more detailed maps of depth to bedrock exist show that there is a general match with spatial patterns from similar local studies. Limitation of the data set and extrapolation in data spare areas should not be ignored in applications. To improve accuracy of spatial prediction, more borehole drilling logs will need to be added to supplement the existing training points in under-represented areas.

IN SITU MEASUREMENT OF BEDROCK EROSION

Directory of Open Access Journals (Sweden)

D. H. Rieke-Zapp

2012-07-01

Full Text Available While long term erosion rates of bedrock material may be estimated by dating methods, current day erosion rates are – if at all available – based on rough estimates or on point measurements. Precise quantification of short term erosion rates are required to improve our understanding of short term processes, for input in landscape evolution models, as well as for studying the mechanics and efficiency of different erosion processes in varying geomorphological settings. Typical current day erosion rates in the European Alps range from sub-millimetre to several millimetres per year depending on the dominant erosion processes. The level of surveying accuracy required for recurring sub-millimetre to millimetre measurements in the field is demanding. A novel surveying setup for in-situ measurement of bedrock erosion was tested recently in three different locations in Switzerland. Natural bedrock was investigated in the Gornera gorge close to Zermatt. Further on, bedrock samples were installed in exposed locations in the Erlenbach research watershed close to Einsiedeln, and in the Illgraben debris flow channel, located in the Canton Schwyz and Valais, respectively. A twofold measurement approach was chosen for all locations. For the first setup control points providing an absolute reference frame for recurrent measurements were embedded close to the area of interest. Close range photogrammetry was applied to measure surface changes on the bedrock samples. The precision for surface measurements in the field was 0.1 mm (1 σ and thus suitable for the application. The equipment needed for the surveys can easily be carried to the field. At one field site a structured light scanner was used along with the photogrammetric setup. Although the current generation of structured light scanners appeared less suitable for field application, data acquisition was much faster and checking the data for completeness in the field was straight forward. The latest

In Situ Measurement of Bedrock Erosion

Science.gov (United States)

Rieke-Zapp, D. H.; Beer, A.; Turowski, J. M.; Campana, L.

2012-07-01

While long term erosion rates of bedrock material may be estimated by dating methods, current day erosion rates are - if at all available - based on rough estimates or on point measurements. Precise quantification of short term erosion rates are required to improve our understanding of short term processes, for input in landscape evolution models, as well as for studying the mechanics and efficiency of different erosion processes in varying geomorphological settings. Typical current day erosion rates in the European Alps range from sub-millimetre to several millimetres per year depending on the dominant erosion processes. The level of surveying accuracy required for recurring sub-millimetre to millimetre measurements in the field is demanding. A novel surveying setup for in-situ measurement of bedrock erosion was tested recently in three different locations in Switzerland. Natural bedrock was investigated in the Gornera gorge close to Zermatt. Further on, bedrock samples were installed in exposed locations in the Erlenbach research watershed close to Einsiedeln, and in the Illgraben debris flow channel, located in the Canton Schwyz and Valais, respectively. A twofold measurement approach was chosen for all locations. For the first setup control points providing an absolute reference frame for recurrent measurements were embedded close to the area of interest. Close range photogrammetry was applied to measure surface changes on the bedrock samples. The precision for surface measurements in the field was 0.1 mm (1 σ) and thus suitable for the application. The equipment needed for the surveys can easily be carried to the field. At one field site a structured light scanner was used along with the photogrammetric setup. Although the current generation of structured light scanners appeared less suitable for field application, data acquisition was much faster and checking the data for completeness in the field was straight forward. The latest generation of compact

Effect of the settlement of sediments on water infiltration in two urban infiltration basins

OpenAIRE

LASSABATERE, Laurent; ANGULO JARAMILLO, R; GOUTALAND, David; LETELLIER, Laetitia; GAUDET, JP; WINIARSKI, Thierry; DELOLME, C

2010-01-01

The sealing of surfaces in urban areas makes storm water management compulsory. The suspended solids from surface runoff water accumulate in infiltration basins and may impact on water infiltration. This paper describes a study of the effect of the settlement of sedimentary layers on the water infiltration capacity of two urban infiltrations basins. In situ water infiltration experiments were performed (1) to quantify the effect of sediment on water infiltration at local scale and (2) to deri...

Complementary investigations of the bedrock in the Finnsjoe and Karlshamn areas, Sweden

International Nuclear Information System (INIS)

Olkiewicz, A.; Scherman, S.; Kornfaelt, K.-A.

1979-02-01

In its statement of the 1978-10-05 the government decided that the KBS' reports I and II did not prove the existance of a''sufficiently large'' geological formation with the qualities which were required in the KBS risk analysis. The government therefore demanded further investigations. Complementary investigations were carried out in two areas, Finnsjoen in northwestern Uppland and Sternoe in southwestern Blekinge, Sweden. This report comprises mapping of the drillcores and extended geological mapping of the actual investigated areas. Measurements of borehole-deviation as well as surface-geophysical investigations from the Finnsjoen area are enclosed. The mapping of the four drill-cores in the Finnsjoe area shows that the cores are dominated by a slightly gneissic granodiorite. Of secondary importance occurs a young red homogenous granite. The frequency of fractures and fracture sets is high and evenly distributed. The tectonized parts are very often red coloured, foliated and containing many calcite healed fractures. The mapping also shows that mylonites and breccias are common in connection with more disturbed zones. Fractures are usually lined with calcite and chlorite. The mapping of these five new boreholes at Sternoe (one of the holes an extension of Ka 1 from earlier investigations) shows quite a complex picture of the bedrock. This is probably an effect of granitization of the coastal gneiss. Close to the surface coastal gneiss is dominating, in the deeper sections granitic material, gneissgranite and granite, are dominating. Pegmatites are common in the shallow sections of the area investigated. The frequency of fractures and fracture sets are very low. The only exception is one core, Ka 4, drilled in close connection with a thrust-zone in ''Munkahusviken''. Coatings of fracture surfaces are dominated by calcite and gypsum. (author)

Blast fracturing of bedrock to enhance recovery of contaminated groundwater

International Nuclear Information System (INIS)

Holzman, L.R.; Harvey, E.M.; McKee, R.C.E.; Katsabanis, T.

1992-01-01

Petroleum hydrocarbons releasd from a pipeline at a site in southern Ontario had contaminated a fractured dolostone bedrock aquifer. To remediate the site, contaminated groundwater was pumped from the downgradient edge of the hydrocarbon plume and injected into an upgradient area after treatment. Contaminant flow pathways in the fractured bedrock aquifer were found to be complex and erratic. It was anticipated that contaminated groundwater could escape the influence of a line of closely spaced recovery wells. In order to capture the migrating contaminants effectively, improve communication between recovery wells, and optimize pumping efficiencies, a rubble zone was created by drilling and blasting the rock. Using 140 blastholes, the bedrock was fractured to a depth of 4 m over a distance of 200 m. Similarly, an additional 80 blastholes were used to blast fracture 100 m of bedrock to a depth of 4 m in the recharge area to enhance injection of treated water to the aquifer. Various blasthole spacings and explosive loadings and patterns were tested to fracture the rock effectively while minimizing the impact on the nearby pipeline and neighboring residences. Vibrations were carefully monitored using several seismographs. Pump tests conducted before and after the blast indicated the hydraulic connection between the naturally occurring fractures had greatly improved. Monitoring conducted after startup of the pump-treat-and-inject system has confirmed the fracturing provides effective capture and injection of the groundwater. 3 refs., 3 figs., 1 tab

Final disposal of spent nuclear fuel in the Finnish bedrock

International Nuclear Information System (INIS)

1992-12-01

Teollisuuden Voima Oy (TVO) studies Finnish bedrock for the final disposal of the spent nuclear fuel from the Olkiluoto nuclear power plant. The study is in accordance with the decision in principle by Finnish government in 1983. The report is the summary of the preliminary site investigations carried out during the years 1987-1992. On the basis of these investigations a few areas will be selected for detailed site investigation. The characterization comprises five areas selected from the shortlist of potential candidate areas resulted in the earlier study during 1983-1985. Areas are located in different parts of Finland and they represent the main formations of the Finnish bedrock. Romuvaara area in Kuhmo and Veitsivaara area in Hyrynsalmi represent the Archean basement. Kivetty area in Konginkangas consists of mainly younger granitic rocks. Syyry in Sievi is located in transition area of Svecofennidic rocks and granitic rocks. Olkiluoto in Eurajoki represents migmatites in southern Finland. For the field investigations area-specific programs were planned and executed. The field investigations have comprised airborne survey by helicopter, geophysical surveys, geological mappings and samplings, deep and shallow core drillings, geophysical and hydrological borehole measurements and groundwater samplings

Hydrogeologic and geochemical characterization and evaluation of two arroyos for managed aquifer recharge by surface infiltration in the Pojoaque River Basin, Santa Fe County, New Mexico, 2014–15

Science.gov (United States)

Robertson, Andrew J.; Cordova, Jeffrey; Teeple, Andrew; Payne, Jason; Carruth, Rob

2017-02-22

In order to provide long-term storage of diverted surface water from the Rio Grande as part of the Aamodt water rights settlement, managed aquifer recharge by surface infiltration in Pojoaque River Basin arroyos was proposed as an option. The initial hydrogeologic and geochemical characterization of two arroyos located within the Pojoaque River Basin was performed in 2014 and 2015 in cooperation with the Bureau of Reclamation to evaluate the potential suitability of these two arroyos as sites for managed aquifer recharge through surface infiltration.The selected reaches were high-gradient (average 3.0–3.5 percent) braided channels filled with unconsolidated sand and gravel-sized deposits that were generally 30–50 feet thick. Saturation was not observed in the unconsolidated channel sands in four subsurface borings but was found at 7–60 feet below the contact between the unconsolidated channel sands and the bedrock. The poorly to well-cemented alluvial deposits that make up the bedrock underlying the unconsolidated channel material is the Tesuque Formation. The individual beds of the Tesuque Formation are reported to be highly heterogeneous and anisotropic, and the bedrock at the site was observed to have variable moisture and large changes in lithology. Surface electrical-resistivity geophysical survey methods showed a sharp contrast between the electrically resistive unconsolidated channel sands and the highly conductive bedrock; however, because of the high conductivity, the resistivity methods were not able to image the water table or preferential flow paths (if they existed) in the bedrock.Infiltration rates measured by double-ring and bulk infiltration tests on a variety of channel morphologies in the study reaches were extremely large (9.7–94.5 feet per day), indicating that the channels could potentially accommodate as much as 6.6 cubic feet per second of applied water without generating surface runoff out of the reach; however, the small volume

Facial infiltrative lipomatosis

International Nuclear Information System (INIS)

Haloi, A.K.; Ditchfield, M.; Pennington, A.; Philips, R.

2006-01-01

Although there are multiple case reports and small series concerning facial infiltrative lipomatosis, there is no composite radiological description of the condition. Radiological evaluation of facial infiltrative lipomatosis using plain film, sonography, CT and MRI. We radiologically evaluated four patients with facial infiltrative lipomatosis. Initial plain radiographs of the face were acquired in all patients. Three children had an initial sonographic examination to evaluate the condition, followed by MRI. One child had a CT and then MRI. One child had abnormalities on plain radiographs. Sonographically, the lesions were seen as ill-defined heterogeneously hypoechoic areas with indistinct margins. On CT images, the lesions did not have a homogeneous fat density but showed some relatively more dense areas in deeper parts of the lesions. MRI provided better delineation of the exact extent of the process and characterization of facial infiltrative lipomatosis. Facial infiltrative lipomatosis should be considered as a differential diagnosis of vascular or lymphatic malformation when a child presents with unilateral facial swelling. MRI is the most useful single imaging modality to evaluate the condition, as it provides the best delineation of the exact extent of the process. (orig.)

Bedrock hydrogeology Forsmark. Site descriptive modelling, SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

Follin, Sven (SF GeoLogic AB, Taeby (Sweden))

2008-12-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations at two different locations, the Forsmark and Laxemar-Simpevarp areas, with the objective of siting a final repository for spent nuclear fuel according to the KBS-3 concept. Site characterisation should provide all data required for an integrated evaluation of the suitability of the investigated site and an important component in the characterisation work is the development of a hydrogeological model. The hydrogeological model is used by repository engineering to design the underground facility and to develop a repository layout adapted to the site. It also provides input to the safety assessment. Another important use of the hydrogeological model is in the environmental impact assessment. This report presents the understanding of the hydrogeological conditions of the bedrock at Forsmark reached following the completion of the surface-based investigations and provides a summary of the bedrock hydrogeological model and the underlying data supporting its development. It constitutes the main reference on bedrock hydrogeology for the site descriptive model concluding the surface-based investigations at Forsmark, SDM-site, and is intended to describe the hydraulic properties and hydrogeological conditions of the bedrock at the site and to give the information essential for demonstrating understanding

UNSAT-H infiltration model calibration at the Subsurface Disposal Area, Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Martian, P.

1995-10-01

Soil moisture monitoring data from the expanded neutron probe monitoring network located at the Subsurface Disposal Area (SDA) of the Idaho National Engineering Laboratory (INEL) were used to calibrate numerical infiltration models for 15 locations within and near the SDA. These calibrated models were then used to simulate infiltration into the SDA surficial sediments and underlying basalts for the entire operational period of the SDA (1952--1995). The purpose of performing the simulations was to obtain a time variant infiltration source term for future subsurface pathway modeling efforts as part of baseline risk assessment or performance assessments. The simulation results also provided estimates of the average recharge rate for the simulation period and insight into infiltration patterns at the SDA. These results suggest that the average aquifer recharge rate below the SDA may be at least 8 cm/yr and may be as high as 12 cm/yr. These values represent 38 and 57% of the average annual precipitation occurring at the INEL, respectively. The simulation results also indicate that the maximum evaporative depth may vary between 28 and 148 cm and is highly dependent on localized lithology within the SDA

Groundwater management in coastal zones and on islands in crystalline bedrock areas of Sweden

Science.gov (United States)

Banzhaf, Stefan; Ekström, Linda Louise; Ljungkvist, Andreas; Granberg, Maria; Merisalu, Johanna; Pokorny, Sebastian; Barthel, Roland

2017-04-01

Groundwater problems in coastal regions are usually not associated with the sparsely populated shores of water-rich Scandinavia. However, the combination of geology and the specific conditions of water usage create challenges even there. Along the Swedish coast, much of the groundwater occurs in fractured bedrock or in relatively small, shallow, and isolated quaternary sedimentary formations. Those aquifers cannot provide water to larger permanent settlements and are thus neither useful for the public water supply nor have previously received much attention from water authorities or researchers. However, of the 450,000 private wells in Sweden, many are located in coastal areas or on islands, creating pressure on groundwater resources in summer months as periods with low or no natural groundwater recharge. In view of the increasing water demand, as well as the awareness of environmental impacts and climate change, Swedish municipalities now recognize groundwater usage in coastal areas is a major concern. Here, we present the results of an investigation on the "Koster" archipelago which forms a microcosm of coastal zone groundwater problems in Sweden. Koster's geology is dominated by fractured, crystalline bedrock with occasional shallow quaternary deposits in between. With around 300 permanent residents, and up to 6,000 summer guests in peak holiday season, the existing water supply based on 800 private wells is at its limit. Water availability forms an obstacle to future development and the current mode of operation is unsustainable. Therefore, the municipality must decide how to secure future water supply which involves complex legal problems, as well as social, cultural, economic, hydrogeological, and environmental questions. As there are no observation wells on the islands, we used approximately 220 of the 800 wells (65% dug and shallow, 35% drilled and up to 120m deep) for our monitoring. Additionally, water samples were collected by property owners on four

Spatial Pattern of Groundwater Arsenic Occurrence and Association with Bedrock Geology in Greater Augusta, Maine, USA

Science.gov (United States)

Yang, Qiang; Jung, Hun Bok; Culbertson, Charles W.; Marvinney, Robert G.; Loiselle, Marc C.; Locke, Daniel B.; Cheek, Heidi; Thibodeau, Hilary; Zheng, Yan

2009-01-01

In New England, groundwater arsenic occurrence has been linked to bedrock geology on regional scales. To ascertain and quantify this linkage at intermediate (100-101 km) scales, 790 groundwater samples from fractured bedrock aquifers in the greater Augusta, Maine area are analyzed. 31% of the sampled wells have arsenic >10 μg/L. The probability of [As] exceeding 10 μg/L mapped by indicator kriging is highest in Silurian pelite-sandstone and pelite-limestone units (~40%). This probability differs significantly (pbedrock map. Thus, bedrock geology is associated with arsenic occurrence in fractured bedrock aquifers of the study area at intermediate scales relevant to water resources planning. The arsenic exceedance rate for each rock unit is considered robust because low, medium and high arsenic occurrences in 4 cluster areas (3-20 km2) with a low sampling density of 1-6 wells per km2 are comparable to those with a greater density of 5-42 wells per km2. About 12,000 people (21% of the population) in the greater Augusta area (~1135 km2) are at risk of exposure to >10 μg/L arsenic in groundwater. PMID:19475939

Morphodynamic simulation of sediment deposition patterns on a recently stripped bedrock anastomosed channel

Directory of Open Access Journals (Sweden)

D. Milan

2018-04-01

Full Text Available Some mixed bedrock-alluvial dryland rivers are known to undergo cycles of alluvial building during low flow periods, punctuated by stripping events during rare high magnitude flows. We focus on the Olifants River, Kruger National Park, South Africa, and present 2-D morphodynamic simulations of hydraulics and sediment deposition patterns over an exposed bedrock anastomosed pavement. We examine the assumptions underlying a previous conceptual model, namely that sedimentation occurs preferentially on bedrock highs. Our modelling results and local field observations in fact show that sediment thicknesses are greater over bedrock lows, suggesting these are the key loci for deposition, barform initiation and island building. During peak flows, velocities in the topographic lows tend to be lower than in intermediate topographic areas. It is likely that intermediate topographic areas supply sediment to the topographic lows at this flow stage, which is then deposited in the lows on the falling limb of the hydrograph as velocities reduce. Subsequent vegetation establishment on deposits in the topographic lows is likely to play a key role in additional sedimentation and vegetation succession, both through increasing the cohesive strength of alluvial units and by capturing new sediments and propagules.

Morphodynamic simulation of sediment deposition patterns on a recently stripped bedrock anastomosed channel

Science.gov (United States)

Milan, David; Heritage, George; Entwistle, Neil; Tooth, Stephen

2018-04-01

Some mixed bedrock-alluvial dryland rivers are known to undergo cycles of alluvial building during low flow periods, punctuated by stripping events during rare high magnitude flows. We focus on the Olifants River, Kruger National Park, South Africa, and present 2-D morphodynamic simulations of hydraulics and sediment deposition patterns over an exposed bedrock anastomosed pavement. We examine the assumptions underlying a previous conceptual model, namely that sedimentation occurs preferentially on bedrock highs. Our modelling results and local field observations in fact show that sediment thicknesses are greater over bedrock lows, suggesting these are the key loci for deposition, barform initiation and island building. During peak flows, velocities in the topographic lows tend to be lower than in intermediate topographic areas. It is likely that intermediate topographic areas supply sediment to the topographic lows at this flow stage, which is then deposited in the lows on the falling limb of the hydrograph as velocities reduce. Subsequent vegetation establishment on deposits in the topographic lows is likely to play a key role in additional sedimentation and vegetation succession, both through increasing the cohesive strength of alluvial units and by capturing new sediments and propagules.

Significance and estimations of lifetime of natural fracture mineral buffers in the Olkiluoto bedrock

International Nuclear Information System (INIS)

Luukkonen, A.; Pitkaenen, P.; Partamies, S.

2004-03-01

This study attempts to make scenarios what geochemical effects the future underground excavations in the Olkiluoto bedrock have on naturally occurring fracture mineral buffers. The excavations of underground research facilities, and final repository galleries will cause steep hydraulic gradients in the bedrock fractures. These gradients likely draw surficial waters within the fracture network and activate weathering processes deeper in rock fractures than in the natural undisturbed conditions. The studies are concentrated on the meteoric and seawater infiltration in the rock fractures, and on the selected minerals considered significant buffers against pH/redox variations in groundwater. Two approaches to calculate the scenarios are utilised. The equilibrium geochemical calculations consider variety of problems including several surficial water compositions, mixing cases between surficial water types, and couple buffer mineral assemblages. These equilibrium calculations indicate that meteoric water by far presents the most potential hazard for the Olkiluoto fracture minerals. In the calculated cases, seawater and the contamination of meteoric water with seawater during the water infiltration usually improved the performance of mineral buffers compared to the pure meteoric water cases. Of the Olkiluoto fracture minerals, calcite and pyrite turn out to be the most important buffer minerals against dissolved O 2 and low pH in groundwater. The kinetic geochemical approach concentrated on two meteoric water cases infiltrating into a narrow fracture channel. Calculations consider the possibilities that the infiltrating meteoric water is dissolved carbon containing soil water or almost 'distilled' rain water. Pyrite and calcite are taken into account as the buffering minerals. Several simulations are done by varying the recharge water compositions and the flow rates of water. It turns out that as long as volumetric flow rates within the 500-metre-channel considered are in

The Contraption and Engineering Implementation of Linked Fracture of Shoal Suture in the Bedrock

OpenAIRE

Korošec, Ludvik; Kralj, Lojze

2015-01-01

The characteristics of overburden strata structural features of typical shallow seam with thin bedrock in Shandong mining area is: there is only one key stratum which controls the overburden strata movement (main roof), when the thickness of bedrock is smaller (generally less than 50-60 m) and the key stratum located under the fissure zone or inside the caving zone through the analysis combined geological data Shandong mining area with the experience in mining practice for a long time. Strata...

Groundwater in crystalline bedrock

International Nuclear Information System (INIS)

Palmqvist, K.

1990-06-01

The aim of this project was to make detailed descriptions of the geological conditions and the different kinds of leakage in some tunnels in Sweden, to be able to describe the presence of ground water in crystalline bedrock. The studies were carried out in TBM tunnels as well as in conventionally drilled and blasted tunnels. Thanks to this, it has been possible to compare the pattern and appearance of ground water leakage in TBM tunnels and in blasted tunnels. On the basis of some experiments in a TBM tunnel, it has been confirmed that a detailed mapping of leakage gives a good picture of the flow paths and their aquiferous qualities in the bedrock. The same picture is found to apply even in cautious blasted tunnels. It is shown that the ground water flow paths in crystalline bedrock are usually restricted to small channels along only small parts of the fractures. This is also true for fracture zones. It has also been found that the number of flow paths generally increases with the degree of tectonisation, up to a given point. With further tectonisation the bedrock is more or less crushed which, along with mineral alteration, leaves only a little space left for the formation of water channels. The largest individual flow paths are usually found in fracture zones. The total amount of ground water leakage per m tunnel is also greater in fracture zones than in the bedrock between the fracture zones. In mapping visible leakage, five classes have been distinguished according to size. Where possible, the individual leak inflow has been measured during the mapping process. The quantification of the leakage classes made in different tunnels are compared, and some quantification standards suggested. A comparison of leakage in different rock types, tectonic zones, fractures etc is also presented. (author)

Bedrock Geologic Map of Woodstock, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG06-4 Thompson, P. J., 2006, Bedrock Geologic Map of Woodstock, Vermont: VGS Open-File Report VG06-4, scale 1:24,000. The bedrock geologic map...

Faulting in unconsolidated sediments and bedrock east of Toronto - phase 1

International Nuclear Information System (INIS)

Rogojina, C.; Mohajer, A.A.; Eyles, N.

1995-10-01

Increasing concern with the potential earthquake hazard in southern Ontario has focused attention on neotectonic structures affecting bedrock. Within the boundaries of the metropolitan Toronto area (632 km 2 ), about 2500 fracture orientations have been measured in more than 70 bedrock outcrops. An east-northeast systematic fracture set constitute the most commonly-oriented fundamental fracture system in the study area. The east-northeast systematic fracture set may be the product of the current compressive stress field combined with regional uplift, but this should be confirmed by further field investigation. Anomalous fracture patterns were identified at the periphery of Metropolitan Toronto, specifically along the West Humber and Rouge rivers. Four post-glacial pop-ups were identified within Metro Toronto. Careful mapping and description of these pop-ups show a possible relationship with the contemporary principal stresses in the area and the local fracture pattern. (author). 41 refs., 8 figs

The make up of crystalline bedrock - crystalline body and blocks

International Nuclear Information System (INIS)

Huber, M.; Huber, A.

1986-01-01

Statements of a geological nature can be made on the basis of investigations of the bedrock exposed in southern Black Forest and these can, in the form of prognoses, be applied to the crystalline Basement of northern Switzerland. Such statements relate to the average proportions of the main lithological groups at the bedrock surface and the surface area of the granite body. Some of the prognoses can be compared and checked with the results from the deep drilling programme in northern Switzerland. Further, analogical interferences from the situation in the southern Black Forest allow predictions to be made on the anticipated block structure of the crystalline Basement. (author)

Assessing the velocity of the groundwater flow in bedrock fractures

International Nuclear Information System (INIS)

Taivassalo, V.; Poteri, A.

1994-10-01

Teollisuuden Voima Oy (TVO) is studying the crystalline bedrock in Finland for the final disposal of the spent nuclear fuel from its two reactors in Olkiluoto. Preliminary site investigations for five areas were carried out during 1987-1992. One part of the investigation programme was three-dimensional groundwater flow modelling. The numerical site-specific flow simulations were based on the concept of an equivalent porous continuum. The results include hydraulic head distributions, average groundwater flow rate routes. In this study, a novel approach was developed to evaluate the velocities of the water particles flowing in the fractured bedrock. (17 refs., 15 figs., 5 tabs.)

Modelling Waterfall Retreat in Heterogenous Bedrock

Science.gov (United States)

Attal, M.; Hodge, R. A.; Williams, R.; Baynes, E.

2016-12-01

Bedrock rivers are the mediators of environmental change through mountainous landscapes. In response to an increase in uplift rate for example, a "knickpoint" (often materialised as a waterfall) will propagate upstream, separating a domain downstream where the river and its adjacent hillslopes have steepened in response to the change from a "relict" domain upstream which is adjusted to the conditions before the change (Crosby and Whipple 2006). Many studies assume that knickpoint propagation rate scales with drainage area, based on the stream power theory. However, recent studies in a range of locations have found no obvious relationship between knickpoint retreat rate and drainage area, potentially resulting from the stream power law neglecting (i) the influence of sediment on the processes associated with waterfall migration and (ii) thresholds for bedrock detachment (Cook et al. 2013; Mackey et al. 2014; DiBiase et al. 2015; Baynes et al. 2015; Brocard et al. 2016). In this study, we develop a 1D model of waterfall retreat in horizontally bedded bedrock with varying joint spacing. In the model, knickpoint migration is based on two rules: a waterfall will start migrating once the threshold flow depth (a function of knickpoint height and joint spacing) has been exceeded (Lamb and Dietrich 2009), and the migration rate will then be a function of the water-depth-to-waterfall-height ratio, based on experimental results by Baynes (2015). Using a hydrograph based on a Poisson rectangular pulse rainfall simulator (Tucker and Bras 2001), we demonstrate the importance of structure in controlling the speed at which waterfalls migrate but also their number and the length over which they are distributed (Fig. 1). The model is applied to the Jökulsá á Fjöllum, NE Iceland, where rapid migration of waterfalls as a result of discrete events has been identified (Baynes et al. 2015), using new constraints on joint spacing derived from high resolution lidar survey of the gorge

2D soil and engineering-seismic bedrock modeling of eastern part of Izmir inner bay/Turkey

Science.gov (United States)

Pamuk, Eren; Akgün, Mustafa; Özdağ, Özkan Cevdet; Gönenç, Tolga

2017-02-01

Soil-bedrock models are used as a base when the earthquake-soil common behaviour is defined. Moreover, the medium which is defined as bedrock is classified as engineering and seismic bedrock in itself. In these descriptions, S-wave velocity is (Vs) used as a base. The mediums are called soil where the Vs is bedrock as well. Additionally, the parts are called engineering bedrock where the Vs is between 3000 m/s and 760 m/s, the parts where are bigger than 3000 m/s called seismic bedrock. The interfacial's horizontal topography where is between engineering and seismic bedrock is effective on earthquake's effect changing on the soil surface. That's why, 2D soil-bedrock models must be used to estimate the earthquake effect that could occur on the soil surface. In this research, surface wave methods and microgravity method were used for occuring the 2D soil-bedrock models in the east of İzmir bay. In the first stage, velocity values were obtained by the studies using surface wave methods. Then, density values were calculated from these velocity values by the help of the empiric relations. 2D soil-bedrock models were occurred based upon both Vs and changing of density by using these density values in microgravity model. When evaluating the models, it was determined that the soil is 300-400 m thickness and composed of more than one layers in parts where are especially closer to the bay. Moreover, it was observed that the soil thickness changes in the direction of N-S. In the study area, geologically, it should be thought the engineering bedrock is composed of Bornova melange and seismic bedrock unit is composed of Menderes massif. Also, according to the geophysical results, Neogene limestone and andesite units at between 200 and 400 m depth show that engineering bedrock characteristic.

Calculating the spatio-temporal variability of bedrock exposure on seasonal hydrograph timescales as a prerequisite to modeling bedrock river evolution

Science.gov (United States)

Hurst, A. A.; Anderson, R. S.; Tucker, G. E.

2017-12-01

Erosion of bedrock river channels exerts significant control on landscape evolution because it communicates climatic and tectonic signals across a landscape by setting the lower erosional boundaries for hillslopes. Hillslope erosion delivers sediment to the channels, which then either store or transport the sediment. At times of high storage, access to the bedrock floor of the channel is limited, inhibiting bedrock erosion. This affects the timescale of channel response to imposed base-level lowering, which in turn affects hillslope erosion. Because occasional exposure of the bedrock bed is a minimum prerequisite for bedrock erosion, we seek to understand the evolution of sediment cover, or scour history, with sufficient resolution to answer when and where the bed is exposed. The scour history at a site is governed by grain size, bed and channel morphology, sediment concentration in the water, and seasonal flow conditions (hydrograph). The transient nature of bedrock exposure during high-flow events implies that short-term sediment cover dynamics are important for predicting long-term bedrock incision rates. Models of channel profile evolution, or of landscape evolution, generally ignore evolution of sediment cover on the hydrograph timescale. To develop insight into the necessary and sufficient conditions for bedrock exposure followed by reburial, we have developed a 1-D model of the evolution of alluvial cover thickness in a long channel profile in response to a seasonal hydrograph. This model tracks erosion, deposition, and the concentration of sediment in the water column separately, and generates histories of scour and fill over the course of the hydrograph. We compare the model's predictions with net-scour measurements in tributaries of the Grand Canyon and with scour-chain and accelerometer measurements in the Cedar River, Washington. By addressing alluvial scour on short timescales, we acknowledge the processes required to allow bedrock incision and

Formative flow in bedrock canyons

Science.gov (United States)

Venditti, J. G.; Kwoll, E.; Rennie, C. D.; Church, M. A.

2017-12-01

In alluvial channels, it is widely accepted that river channel configuration is set by a formative flow that represents a balance between the magnitude and frequency of flood flows. The formative flow is often considered to be one that is just capable of filling a river channel to the top of its banks. Flows much above this formative flow are thought to cause substantial sediment transport and rearrange the channel morphology to accommodate the larger flow. This idea has recently been extended to semi-alluvial channels where it has been shown that even with bedrock exposed, the flows rarely exceed that required to entrain the local sediment cover. What constitutes a formative flow in a bedrock canyon is not clear. By definition, canyons have rock walls and are typically incised vertically, removing the possibility of the walls being overtopped, as can occur in an alluvial channel at high flows. Canyons are laterally constrained, have deep scour pools and often have width to maximum depth ratios approaching 1, an order of magnitude lower than alluvial channels. In many canyons, there are a sequence of irregularly spaced scour pools. The bed may have intermittent or seasonal sediment cover, but during flood flows the sediment bed is entrained leaving a bare bedrock channel. It has been suggested that canyons cut into weak, well-jointed rock may adjust their morphology to the threshold for block plucking because the rock bed is labile during exceptionally large magnitude flows. However, this hypothesis does not apply to canyons cut into massive crystalline rock where abrasion is the dominant erosion process. Here, we argue that bedrock canyon morphology is adjusted to a characteristic flow structure developed in bedrock canyons. We show that the deeply scoured canyon floor is adjusted to a velocity inversion that is present at low flows, but gets stronger at high flows. The effect is to increase boundary shear stresses along the scour pool that forms in constricted

Bedrock morphology and structure, upper Santa Cruz Basin, south-central Arizona, with transient electromagnetic survey data

Science.gov (United States)

Bultman, Mark W.; Page, William R.

2016-10-31

The upper Santa Cruz Basin is an important groundwater basin containing the regional aquifer for the city of Nogales, Arizona. This report provides data and interpretations of data aimed at better understanding the bedrock morphology and structure of the upper Santa Cruz Basin study area which encompasses the Rio Rico and Nogales 1:24,000-scale U.S. Geological Survey quadrangles. Data used in this report include the Arizona Aeromagnetic and Gravity Maps and Data referred to here as the 1996 Patagonia Aeromagnetic survey, Bouguer gravity anomaly data, and conductivity-depth transforms (CDTs) from the 1998 Santa Cruz transient electromagnetic survey (whose data are included in appendixes 1 and 2 of this report).Analyses based on magnetic gradients worked well to identify the range-front faults along the Mt. Benedict horst block, the location of possibly fault-controlled canyons to the west of Mt. Benedict, the edges of buried lava flows, and numerous other concealed faults and contacts. Applying the 1996 Patagonia aeromagnetic survey data using the horizontal gradient method produced results that were most closely correlated with the observed geology.The 1996 Patagonia aeromagnetic survey was used to estimate depth to bedrock in the upper Santa Cruz Basin study area. Three different depth estimation methods were applied to the data: Euler deconvolution, horizontal gradient magnitude, and analytic signal. The final depth to bedrock map was produced by choosing the maximum depth from each of the three methods at a given location and combining all maximum depths. In locations of rocks with a known reversed natural remanent magnetic field, gravity based depth estimates from Gettings and Houser (1997) were used.The depth to bedrock map was supported by modeling aeromagnetic anomaly data along six profiles. These cross sectional models demonstrated that by using the depth to bedrock map generated in this study, known and concealed faults, measured and estimated magnetic

The suitability of Finnish bedrock to the final disposal of high-level radioactive waste

International Nuclear Information System (INIS)

Vuorela, P.; Hakkarainen, V.

1982-12-01

A regional investigation of the suitability of Finnish bedrock to the final disposal of high-level radioactive waste is described. International geological criteria are applied to Finnish bedrock conditions. The main bedrock units are classified into different areas as concerning to recommendations for further site selection investigations. The Pre-Cambrian crystalline rocks are generally of tight and strong composition and a major problem from the standpoint of waste disposal is fracturing. On the other hand, fractures are quite unevenly distributed in Finland and the bedrock seems to consist of stabile blocks surrounded by fracture zones. Crustal movements between the different bedrock blocks are in Finland at most only tenths of millimeters a year, and the movements are concentrated in the fracture zones. The fracture pattern also controls the hydrogeological system of the bedrock as the main groundwater flow occurs along the fractures. The fracturing thus has an influence on the stability as well as the hydrogeological conditions of the bedrock. The regional recommendations for further site selection studies are based on geological criteria, such as fracturing, seismisity and economic resources. Other criteria, such as topography and erosion, are less significant in comparison. A number of different criteria are likely to prove significant later in more detailed local site investigation studies. The most favorable regions for more detailed investigations contain the granitic rocks of Central Finland and some of them are also to be found in northern and eastern parts of the country. Almost none of the main bedrock units can be classified as completely unsuitable for site selection investigations. Massifs large enough for the final disposal of high-level radioactive waste can be found through detailed surveys in most parts of Finland because of the heterogeneity of the bedrock

Geology, Bedrock - BEDROCK_TOPOGRAPHY_MM36_IN: Bedrock Topography Contours, Indiana (Indiana Geological Survey, 1:500,000, Line Shapefile)

Data.gov (United States)

NSGIC State | GIS Inventory — Bedrock topography was converted from the original published map, Indiana Geological Survey Miscellaneous Map 36. The contours define the elevation/topography of the...

Graffiti for science: Qualitative detection of erosional patterns through bedrock erosion painting

Science.gov (United States)

Beer, Alexander R.; Kirchner, James W.; Turowski, Jens M.

2016-04-01

Bedrock erosion is a crucial constraint on stream channel incision, and hence whole landscape evolution, in steep mountainous terrain and tectonically active regions. Several interacting processes lead to bedrock erosion in stream channels, with hydraulic shear detachment, plucking, and abrasion due to sediment impacts generally being the most efficient. Bedrock topography, together with the sediment tools and cover effects, regulate the rate and spatial pattern of in situ surface change. Measurements of natural bedrock erosion rates are valuable for understanding the underlying process physics, as well as for modelling landscape evolution and designing engineered structures. However, quantifying spatially distributed bedrock erosion rates in natural settings is challenging and few such measurements exist. We studied spatial bedrock erosion in a 30m-long bedrock gorge in the Gornera, a glacial meltwater stream above Zermatt. This stream is flushed episodically with sediment-laden streamflow due to hydropower operations upstream, with negligible discharge in the gorge in between these flushing events. We coated several bedrock surface patches with environmentally safe, and water-insoluble outdoor paint to document the spatial pattern of surface abrasion, or to be more precise, to document its driving forces. During four consecutive years, the change of the painted areas was recorded repeatedly with photographs before the painting was renewed. These photographs visually documented the spatial patterns of vertical erosion (channel incision), of lateral erosion (channel widening) and of downstream-directed erosion (channel clearance). The observed qualitative patterns were verified through comparison to quantitative change detection analyses based on annual high-resolution terrestrial laser scanning surveys of the bedrock surfaces. Comparison of repeated photographs indicated a temporal cover effect and a general height limit of the tools effect above the streambed

Matrix Pore Water in Low Permeable Crystalline Bedrock: An Archive for the Palaeohydrogeological Evolution of the Olkiluoto Investigation Site

Energy Technology Data Exchange (ETDEWEB)

Eichinger, F. [Hydroisotop GmbH, Schweitenkirchen (Germany); Waber, H. N. [Rock-Water Interaction, Institute of Geological Sciences, University of Bern, Bern (Switzerland); Smellie, J. A.T. [Conterra AB, Stockholm (Sweden)

2013-07-15

Matrix pore water in the connected inter- and intragranular pore space of low permeable crystalline bedrock interacts with flowing fracture groundwater predominately by diffusion. Based on the slow exchange between the two water reservoirs, matrix pore water acts as an archive of past changes in fracture groundwater compositions and thus of the palaeohydrological history of a site. Matrix pore water of crystalline bedrock from the olkiluoto investigation site (SW Finland) was characterised using the stable water isotopes ({delta}{sup 18}O, {delta}{sup 2}H), combined with the concentrations of dissolved chloride and bromide as natural tracers. The comparison of tracer concentrations in pore water and present day fracture groundwater suggest for the pore water the presence of old, dilute meteoric water components that infiltrated into the fractures during various warm climate stages. These different meteoric components can be discerned based on the diffusion distance between the two reservoirs and brought into context with the palaeohydrological evolution of the site. (author)

Iowa Bedrock Topography

Data.gov (United States)

Iowa State University GIS Support and Research Facility — The Map of the Elevation of the Bedrock Surface in Iowa was compiled using all available data, principally information from GEOSAM, supplemented with well and boring...

Recharge to Shale Bedrock at Averill Park, an Upland Hamlet in Eastern New York - An Estimate Based on Pumpage within a Defined Cone of Depression

Science.gov (United States)

Randall, Allan D.; Finch, Anne

2008-01-01

Water levels beneath parts of Averill Park, a residential hamlet in an upland area of till-mantled shale bedrock in east-central New York, have declined in response to increased withdrawals from new wells. Similar experiences in many upland localities in the northeastern United States have resulted in awareness that the rate of recharge to bedrock can be an important constraint on the density of new development in uplands. Recharge at Averill Park was calculated on the basis of careful estimation of pumpage within a defined cone of depression. The data-collection and recharge-estimation procedures documented herein could be applied in a variety of upland localities in support of community-planning studies. Static water levels measured in 145 wells at Averill Park during the late summer of 2002 defined a 0.54-square-mile cone of depression within which ground-water discharge took place entirely as withdrawals from wells. Rates of withdrawal were estimated largely from surveys in similar neighborhoods a few miles away served by public water supply. Comparison of the water-level measurements in 2002 with measurements on other dates revealed localized declines that could be attributed to new housing developments or commercial demands, but also demonstrated that water levels in 2002 within the cone of depression had stabilized and were not declining persistently over time. Therefore, the current withdrawals were equated to recharge from infiltrating precipitation. Recharge within this area was estimated to average 104 gallons per day per acre, equivalent to 1.4 inches annually, and was sufficient to sustain a residential population of 1.9 persons per acre. This recharge rate is much lower than rates estimated from streamflow records for upland watersheds elsewhere in the northeastern United States. This rate is an average of an unknown larger rate in the 30 percent of the study area where bedrock is discontinuously overlain by less than 30 feet of till and an unknown

Long-term bedrock behavior research for soft rock

International Nuclear Information System (INIS)

Inoue, Hiroyuki; Noda, Kenji

2002-02-01

When a formation disposal system is thought about, it is important to evaluate long-term dynamics behavior of boundary condition and near field bedrock of an artificial barrier adequately. In this study, three matters were executed for improvement of a dependability of the evaluation as follows. (1) Creep test was executed as purpose by dependability improvement of evaluation technique of creep problem by Okubo model. Okubo model constant was calculated than the unconfined compression test which let strain rate change with true rock, and the creep test which the constant was used, and estimated breaking time was done. As a result, the estimation of breaking time by Okubo model almost suffered according to the estimation although a variation of test-piece influenced it. (2) A tunnel model apparatus was produced in the purpose which grasped near field bedrock behavior, and it was tested. Simulation rock test body of 1 m * 1 m * 0.5 m was used for a test, and 15 cm tunnel excavation was carried out in an initial stress bottom. Quantities of inner space displacement were measured in a test, and a hardness-test was done after dismantlement, and looseness area was grasped quantitatively. As a result, the looseness area was able to be estimated with about 17.5 cm than tunnel center position. (3) A test approach in deep underground laboratory was examined, and examination/the in situ test which took advantage of rock core analysis/borehole as purpose and done examination item by grip of long-term bedrock behavior (a bord is taken advantage of, and bord itself is used) was shown. In addition, layout of the deep underground laboratory which carried out various tests about long-term behavior in 3 depth was shown. (author)

Shallow infiltration processes at Yucca Mountain, Nevada: Neutron logging data 1984--1993

International Nuclear Information System (INIS)

Flint, L.E.; Flint, A.L.

1995-01-01

To determine site suitability of Yucca Mountain, Nevada, as a potential high-level radioactive waste repository, a study was devised to characterize net infiltration. This study involves a detailed data set produced from 99 neutron boreholes that consisted of volumetric water-content readings with depth from 1984 through 1993 at Yucca Mountain. Boreholes were drilled with minimal disturbance to the surrounding soil or rock in order to best represent field conditions. Boreholes were located in topographic positions representing infiltration zones identified as ridgetops, sideslopes, terraces, and active channels. Through careful field calibration, neutron moisture logs, collected on a monthly basis and representing most of the areal locations at Yucca Mountain, illustrated that the depth of penetration of seasonal moisture, important for escaping loss to evapotranspiration, was influenced by several factors. It was increased (1) by thin soil cover, especially in locations where thin soil is underlain by fractured bedrock; (2) on ridgetops; and (3) during the winter when evapotranspiration is low and runoff is less frequent. This data set helps to provide a seasonal and areal distribution of changes in volumetric water content with which to assess hydrologic processes contributing to net infiltration

Shallow infiltration processes at Yucca Mountain, Nevada - neutron logging data 1984-93

International Nuclear Information System (INIS)

Flint, L.E.; Flint, A.L.

1995-01-01

To determine site suitability of Yucca Mountain, Nevada, as a potential high-level radioactive waste repository, a study was devised to characterize net infiltration. This study involves a detailed data set produced from 99 neutron boreholes that consisted of volumetric water-content readings with depth from 1984 through 1993 at Yucca Mountain. Boreholes were drilled with minimal disturbance to the surrounding soil or rock in order to best represent field conditions. Boreholes were located in topographic positions representing infiltration zones identified as ridge-tops, sideslopes, terraces, and active channels. Through careful field calibration, neutron moisture logs, collected on a monthly basis and representing most of the areal locations at Yucca Mountain, illustrated that the depth of penetration of seasonal moisture, important for escaping loss to evapotranspiration, was influenced by several factors. It was increased (1) by thin soil cover, especially in locations where thin soil is underlain by fractured bedrock; (2) on ridgetops; and (3) during the winter when evapotranspiration is low and runoff is less frequent. This data set helps to provide a seasonal and areal distribution of changes in volumetric water content with which to assess hydrologic processes contributing to net infiltration

Lithology and Bedrock Geotechnical Properties in Controlling Rock and Ice Mass Movements in Mountain Cryosphere

Science.gov (United States)

Karki, A.; Kargel, J. S.

2017-12-01

Landslides and ice avalanches kill >5000 people annually (D. Petley, 2012, Geology http://dx.doi.org/10.1130/G33217.1); destroy or damage homes and infrastructure; and create secondary hazards, such as flooding due to blocked rivers. Critical roles of surface slope, earthquake shaking, soil characteristics and saturation, river erosional undercutting, rainfall intensity, snow loading, permafrost thaw, freeze-thaw and frost shattering, debuttressing of unstable masses due to glacier thinning, and vegetation burn or removal are well-known factors affecting landslides and avalanches. Lithology-dependent bedrock physicochemical-mechanical properties—especially brittle elastic and shear strength, and chemical weathering properties that affect rock strength, are also recognized controls on landsliding and avalanching, but are not commonly considered in detail in landslide susceptibility assessment. Lithology controls the formation of weakened, weathered bedrock; the formation and accumulation of soils; soil saturation-related properties of grain size distribution, porosity, and permeability; and soil creep related to soil wetting-drying and freeze-thaw. Lithology controls bedrock abrasion and glacial erosion and debris production rates, the formation of rough or smoothed bedrock surface by glaciation, fluvial, and freeze-thaw processes. Lithologic variability (e.g., bedding; fault and joint structure) affects contrasts in chemical weathering rates, porosity, and susceptibility to frost shattering and chemical weathering, hence formation of overhanging outcrops and weakened slip planes. The sudden failure of bedrock or sudden slip of ice on bedrock, and many other processes depend on rock lithology, microstructure (porosity and permeability), and macrostructure (bedding; faults). These properties are sometimes considered in gross terms for landslide susceptibility assessment, but in detailed applications to specific development projects, and in detailed mapping over

Spatial bedrock erosion distribution in a natural gorge

Science.gov (United States)

Beer, A. R.; Turowski, J. M.; Kirchner, J. W.

2015-12-01

Quantitative analysis of morphological evolution both in terrestrial and planetary landscapes is of increasing interest in the geosciences. In mountainous regions, bedrock channel formation as a consequence of the interaction of uplift and erosion processes is fundamental for the entire surface evolution. Hence, the accurate description of bedrock channel development is important for landscape modelling. To verify existing concepts developed in the lab and to analyse how in situ channel erosion rates depend on the interrelations of discharge, sediment transport and topography, there is a need of highly resolved topographic field data. We analyse bedrock erosion over two years in a bedrock gorge downstream of the Gorner glacier above the town of Zermatt, Switzerland. At the study site, the Gornera stream cuts through a roche moutonnée in serpentine rock of 25m length, 5m width and 8m depth. We surveyed bedrock erosion rates using repeat terrestrial laser scanning (TLS) with an average point spacing of 5mm. Bedrock erosion rates in direction of the individual surface normals were studied directly on the scanned point clouds applying the M3C2 algorithm (Lague et al., 2013, ISPRS). The surveyed erosion patterns were compared to a simple stream erosivity visualisation obtained from painted bedrock sections at the study location. Spatially distributed erosion rates on bedrock surfaces based on millions of scan points allow deduction of millimeter-scale mean annual values of lateral erosion, incision and downstream erosion on protruding streambed surfaces. The erosion rate on a specific surface point is shown to depend on the position of this surface point in the channel's cross section, its height above the streambed and its spatial orientation to the streamflow. Abrasion by impacting bedload was likely the spatially dominant erosion process, as confirmed by the observed patterns along the painted bedrock sections. However, a single plucking event accounted for the half

A simulation of rainfall infiltration based on two-phase flow

Science.gov (United States)

Wang, Jun; Xi, Niannian; Liu, Gang; Hao, Shuang

2016-04-01

Rainfall infiltration in slope usually is one of major reasons cause landslide, which involves multiphase flow coupling with soil, water and gas. In order to study the mechanism of landslide caused by rainfall infiltration, a simulation of rainfall infiltration of DaPing slope, which locates in the Three Gorges Region of China, is presented based on the numerical solution of governing equations of two-phase flow in this paper. The results of this research suggest that there are two sections can be divided in the surface of slope, one is inflow area and the other is overflow area, according to where it is infiltration and discharge. The general inflow area is on the upside of slope, while the overflow area is on the underside. The middle section of slope is on a fluctuant position between inflow and overflow area, which is dramatically affected by the water content inside of slope. Moreover, the average rate of infiltration is more stable in both inflow and overflow area, whose numerical value is depend on the geometry and transmission characteristics of slope. And the factors of rainfall characteristics, surface flow and temperature have little effect on them. Furthermore, in the inflow area, when rainfall intensity is higher than infiltration the rain on the surface of slope will run off, otherwise water and gas will completely infiltrate through soil. The situation is different in the overflow area whose overland flow condition is depended on whether it is saturated or not inside of slope. When it is saturated in the slope, there is no infiltration in the overflow area. But when it is unsaturated, the infiltration intensity will equal to rainfall intensity. In a summary, the difference from inflow and overflow area is the evidence that the landslide may likely to happen on the slope of overflow area when it comes to a rainfall. It is disadvantageous for slope stability when transmitting the pressure of saturated water weight at the top of slope through the pore

Pollution from Urban Stormwater Infiltration

DEFF Research Database (Denmark)

Mikkelsen, Peter Steen; Weyer, G.; Berry, C.

1994-01-01

Stormwater infiltration in urban areas gives cause for concern with regard to the risk of soil and groundwater pollution. Compared with conventional storm drainage, infiltration introduces different and widely unknown conditions governing the impacts and the fate of the pollutants......, and it is therefore difficult to assess the overall environmental impact. This paper gives a state of the art assessment of the water quality aspects of stormwater infiltration and proposes ways of managing the inherent problems. The major stormwater pollution sources are highlighted and the different processes...

Bedrock Geologic Map of the Hinesburg Quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from Thompson, P., Thompson, T.B., and Doolan, B., 2004, Bedrock Geology of the Hinesburg quadrangle, Vermont. The bedrock geologic map data at a scale...

Aquifer recharge from infiltration basins in a highly urbanized area: the river Po Plain (Italy)

Science.gov (United States)

Masetti, M.; Nghiem, S. V.; Sorichetta, A.; Stevenazzi, S.; Santi, E. S.; Pettinato, S.; Bonfanti, M.; Pedretti, D.

2015-12-01

Due to the extensive urbanization in the Po Plain in northern Italy, rivers need to be managed to alleviate flooding problems while maintaining an appropriate aquifer recharge under an increasing percentage of impermeable surfaces. During the PO PLain Experiment field campaign in July 2015 (POPLEX 2015), both active and under-construction infiltration basins have been surveyed and analyzed to identify appropriate satellite observations that can be integrated to ground based monitoring techniques. A key strategy is to have continuous data time series on water presence and level within the basin, for which ground based monitoring can be costly and difficult to be obtained consistently.One of the major and old infiltration basin in the central Po Plain has been considered as pilot area. The basin is active from 2003 with ground based monitoring available since 2009 and supporting the development of a calibrated unsaturated-saturated two-dimensional numerical model simulating the infiltration dynamics through the basin.A procedure to use satellite data to detect surface water change is under development based on satellite radar backscatter data with an appropriate incidence angle and polarization combination. An advantage of satellite radar is that it can observe surface water regardless of cloud cover, which can be persistent during rainy seasons. Then, the surface water change is correlated to the reservoir water stage to determine water storage in the basin together with integrated ground data and to give quantitative estimates of variations in the local water cycle.We evaluated the evolution of the infiltration rate, to obtain useful insights about the general recharge behavior of basins that can be used for informed design and maintenance. Results clearly show when the basin becomes progressively clogged by biofilms that can reduce the infiltration capacity of the basin by as much as 50 times compared to when it properly works under clean conditions.

Hydrogeology - AQUIFER_SYSTEMS_BEDROCK_IDNR_IN: Bedrock Aquifer Systems of Indiana (Indiana Department of Natural Resources, 1:500,000, Polygon Shapefile)

Data.gov (United States)

NSGIC State | GIS Inventory — AQUIFER_SYSTEMS_BEDROCK_IDNR_IN is a polygon shapefile that shows bedrock aquifer systems of the State of Indiana. The source scale of the map depicting the aquifers...

Evaluation of some infiltration models and hydraulic parameters

International Nuclear Information System (INIS)

Haghighi, F.; Gorji, M.; Shorafa, M.; Sarmadian, F.; Mohammadi, M. H.

2010-01-01

The evaluation of infiltration characteristics and some parameters of infiltration models such as sorptivity and final steady infiltration rate in soils are important in agriculture. The aim of this study was to evaluate some of the most common models used to estimate final soil infiltration rate. The equality of final infiltration rate with saturated hydraulic conductivity (Ks) was also tested. Moreover, values of the estimated sorptivity from the Philips model were compared to estimates by selected pedotransfer functions (PTFs). The infiltration experiments used the doublering method on soils with two different land uses in the Taleghan watershed of Tehran province, Iran, from September to October, 2007. The infiltration models of Kostiakov-Lewis, Philip two-term and Horton were fitted to observed infiltration data. Some parameters of the models and the coefficient of determination goodness of fit were estimated using MATLAB software. The results showed that, based on comparing measured and model-estimated infiltration rate using root mean squared error (RMSE), Hortons model gave the best prediction of final infiltration rate in the experimental area. Laboratory measured Ks values gave significant differences and higher values than estimated final infiltration rates from the selected models. The estimated final infiltration rate was not equal to laboratory measured Ks values in the study area. Moreover, the estimated sorptivity factor by Philips model was significantly different to those estimated by selected PTFs. It is suggested that the applicability of PTFs is limited to specific, similar conditions. (Author) 37 refs.

REE potential of the Nordkinn Peninsula, North Norway: A comparison of soil and bedrock composition

International Nuclear Information System (INIS)

Schilling, Julian; Reimann, Clemens; Roberts, David

2014-01-01

Highlights: • Soil geochemistry outlines an extensive REE anomaly on the Nordkinn Peninsula, North Norway. • Soil and bedrock geochemistry are compared with respect to REE and other HFSE. • Petrology of soil and rock samples reveals that the economic potential is limited. • Poor condition of REE minerals causes elevated REE concentrations in AR-digested soil samples. - Abstract: Regional-scale, low-density sampling, geochemical surveys using a variety of different sample materials have repeatedly indicated the Nordkinn Peninsula (northern Norway) as a substantial rare earth element (REE) anomaly. Recently, a more detailed soil geochemical survey, covering about 2000 km 2 at a sample density of 1 site per 2 km 2 , was carried out in the area. The new geochemical survey outlined a large area (several hundred km 2 ) where the soil samples contained several hundred and up to over 2000 mg/kg aqua regia extractable REE. In the surroundings of the highest soil anomalies, bedrock samples were collected for a mineralogical and compositional characterisation of the metasedimentary bedrock with focus on the possible economic potential. The REE concentrations obtained for aliquots of bedrock following aqua regia extraction, 4-Acid digestion and Li-borate fusion/decomposition closely match the results from soil pulps after an aqua regia extraction. Total contents for the REE determined in bedrock using the above methods range between 19 and 429 mg/kg, indicating an overall limited economic REE potential and the predominance of the light REE over the heavy REE. In terms of petrography, essentially all the bedrock samples are characterised by the presence of detrital, altered and locally even decomposed allanite (a LREE-incorporating, epidote-group mineral) and minor xenotime (a HREE-incorporating phosphate) while texturally stable REE phases are scarce. It is the poor condition of the REE minerals that makes them prone towards acidic leaching and, given similar results

Weathering of plagioclase across variable flow and solute transport regimes

NARCIS (Netherlands)

Pacheco, F.A.L.; Weijden, C.H. van der

2012-01-01

The study area is situated in a fault zone with fractured granites and metasediments. In a conceptual model, infiltrating water first passes the bedrock cover of soil and saprolite and then partly enters the fractures. Weathering reactions of minerals occur in small pores and fissures in the bedrock

Iowa Bedrock Surface Elevation

Data.gov (United States)

Iowa State University GIS Support and Research Facility — This Digital Elevation Model (DEM) of the bedrock surface elevation in Iowa was compiled using all available data, principally information from GEOSAM, supplemented...

Computed tomographic and ultrasound appearances of focal spared areas in fatty infiltration of the liver

International Nuclear Information System (INIS)

McKenzie, A.; Gill, G.; Hennessy, O.; Pryde, D.

1991-01-01

Computed tomography (CT) and utrasound (US) appearances of diffuse and focal fatty infiltration of the liver (FIL) are well recognized as pseudo tumours of the liver. Characteristic appearances of fat free areas in FIL which help differentiate these areas from other focal liver lesions include location in the medical segment of the left lobe of the liver, absence of mass effect on surrounding vessels and liver tissue, and presence of typical changes of FIL elsewhere in the liver on CT or US examination. 16 refs., 1 tab., 5 figs

A self-regulating model of bedrock river channel geometry

Science.gov (United States)

Stark, C. P.

2006-02-01

The evolution of many mountain landscapes is controlled by the incision of bedrock river channels. While the rate of incision is set by channel shape through its mediation of flow, the channel shape is itself set by the history of bedrock erosion. This feedback between channel geometry and incision determines the speed of landscape response to tectonic or climatic forcing. Here, a model for the dynamics of bedrock channel shape is derived from geometric arguments, a normal flow approximation for channel flow, and a threshold bed shear stress assumption for bedrock abrasion. The model dynamics describe the competing effects of channel widening, tilting, bending, and variable flow depth. Transient solutions suggest that channels may take ~1-10 ky to adapt to changes in discharge, implying that channel disequilibrium is commonplace. If so, landscape evolution models will need to include bedrock channel dynamics if they are to probe the effects of climate change.

Time-lapse electrical surveys to locate infiltration zones in weathered hard rock tropical areas

Science.gov (United States)

Wubda, M.; Descloitres, M.; Yalo, N.; Ribolzi, O.; Vouillamoz, J. M.; Boukari, M.; Hector, B.; Séguis, L.

2017-07-01

In West Africa, infiltration and groundwater recharge processes in hard rock areas are depending on climatic, surface and subsurface conditions, and are poorly documented. Part of the reason is that identification, location and monitoring of these processes is still a challenge. Here, we explore the potential for time-lapse electrical surveys to bring additional information on these processes for two different climate situations: a semi-arid Sahelian site (north of Burkina and a humid Sudanian site (north of Benin), respectively focusing on indirect (localized) and direct (diffuse) recharge processes. The methodology is based on surveys in dry season and rainy season on typical pond or gully using Electrical Resistivity Tomography (ERT) and frequency electromagnetic (FEM) apparent conductivity mapping. The results show that in the Sahelian zone an indirect recharge occurs as expected, but infiltration doesn't takes place at the center of the pond to the aquifer, but occurs laterally in the banks. In Sudanian zone, the ERT survey shows a direct recharge process as expected, but also a complicated behavior of groundwater dilution, as well as the role of hardpans for fast infiltration. These processes are ascertained by groundwater monitoring in adjacent observing wells. At last, FEM time lapse mapping is found to be difficult to quantitatively interpreted due to the non-uniqueness of the model, clearly evidenced comparing FEM result to auger holes monitoring. Finally, we found that time-lapse ERT can be an efficient way to track infiltration processes across ponds and gullies in both climatic conditions, the Sahelian setting providing results easier to interpret, due to significant resistivity contrasts between dry and rain seasons. Both methods can be used for efficient implementation of punctual sensors for complementary studies. However, FEM time-lapse mapping remains difficult to practice without external information that renders this method less attractive for

Ogallala Bedrock Data Enhancement

Data.gov (United States)

Kansas Data Access and Support Center — This data set provides an enhanced estimate of the bedrock elevation of the Ogallala Aquifer in Kansas based on lithologic logs from a variety of sources. The data...

Baseline geochemistry of soil and bedrock Tshirege Member of the Bandelier Tuff at MDA-P

International Nuclear Information System (INIS)

Warren, R.G.; McDonald, E.V.; Ryti, R.T.

1997-08-01

This report provides baseline geochemistry for soils (including fill), and for bedrock within three specific areas that are planned for use in the remediation of Material Disposal Area P (MDA-P) at Technical Area 16 (TA-16). The baseline chemistry includes leachable element concentrations for both soils and bedrock and total element concentrations for all soil samples and for two selected bedrock samples. MDA-P operated from the early 1950s to 1984 as a landfill for rubble and debris generated by the burning of high explosives (HE) at the TA-16 Burning Ground, HE-contaminated equipment and material, barium nitrate sand, building materials, and trash. The aim of this report is to establish causes for recognizable chemical differences between the background and baseline data sets. In many cases, the authors conclude that recognizable differences represent natural enrichments. In other cases, differences are best attributed to analytical problems. But most importantly, the comparison of background and baseline geochemistry demonstrates significant contamination for several elements not only at the two remedial sites near the TA-16 Burning Ground, but also within the entire region of the background study. This contamination is highly localized very near to the surface in soil and fill, and probably also in bedrock; consequently, upper tolerance limits (UTLs) calculated as upper 95% confidence limits of the 95th percentile are of little value and thus are not provided. This report instead provides basic statistical summaries and graphical comparisons for background and baseline samples to guide strategies for remediation of the three sites to be used in the restoration of MDA-P

The bedrock and the soil types in the Finnsjoearea, Sweden

International Nuclear Information System (INIS)

Almen, K.-E.; Ekman, L.; Olkiewicz, A.

1978-11-01

This report is a part of a long-term project, started at the request of the Nuclear Fuel Safety Project, Sweden. The aim of the project is to claryfy the geohydrological situation of a drainage area close to Finnsjoen in northern Uppland, Sweden. The work comprised bedrock- and soil mapping as well as an investigation of existing literature about the geology of northern Uppland. The area is about 25 km 2 and is limited by its water-shed. The area is relatively flat, rich in outcrops - expecially in the western parts - and often swampy. Big areas of forests and agriculture have been drained by ditches. (author)

Perfluorinated compounds in infiltrated river rhine water and infiltrated rainwater in coastal dunes.

Science.gov (United States)

Eschauzier, Christian; Haftka, Joris; Stuyfzand, Pieter J; de Voogt, Pim

2010-10-01

Different studies have shown that surface waters contain perfluorinated compounds (PFCs) in the low ng/L range. Surface waters are used to produce drinking water and PFCs have been shown to travel through the purification system and form a potential threat to human health. The specific physicochemical properties of PFCs cause them to be persistent and some of them to be bioaccumulative and toxic in the environment. This study investigates the evolvement of PFC concentrations in Rhine water and rainwater during dune water infiltration processes over a transect in the dune area of the western part of The Netherlands. The difference between infiltrated river water and rainwater in terms of PFC composition was investigated. Furthermore, isomer profiles were investigated. The compound perfluorobutanesulfonate (PFBS) was found at the highest concentrations of all PFCs investigated, up to 37 ng/L in infiltrated river water (71 ± 13% of ΣPFCs). This is in contrast with the predominant occurrence of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonate (PFOS) reported in literature. The concentrations of PFBS found in infiltrated river Rhine water were significantly higher than those in infiltrated rainwater. For perfluorohexanesulfonate (PFHxS) the opposite was found: infiltrated rainwater contained more than infiltrated river water. The concentrations of PFOA, perfluorohexanoic acid (PFHxA), perfluoroheptanoic acid (PFHpA), PFBS, PFOS, and PFHxS in infiltrated river water showed an increasing trend with decreasing age of the water. The relative contribution of the branched PFOA and PFOS isomers to total concentrations of PFOA and PFOS showed a decreasing trend with decreasing age of the water.

Determination of bedrock depth by using microtremor array survey at the RDE Site Serpong

International Nuclear Information System (INIS)

Hadi Suntoko; Sriyana

2016-01-01

Based on the Strategic Spatial Planning (RTRW) of Tangerang Selatan 2011-2031, PUSPIPTEK Serpong has been appointed as high technology zone, therefore this area is selected as the site for Experimental Power Reactor (Reaktor Daya Eksperimental, RDE). In order to assure safety, site evaluation from several aspects have to be performed, one of which is seismological aspect. Refer to BAPETEN Chairman Regulation No. 8 year 2013, site evaluation should cover the assessment of subsurface geological condition of the site. The objective of this study is to acquire information regarding the subsurface geological condition particularly the bedrock depth of the RDE site area. Method used in this study is micro tremor array (MA). The result shows that RDE site has a bedrock type of Bojongmanik Formation at a depth of 391 meter from the surface. (author)

Cokriging surface elevation and seismic refraction data for bedrock topography

International Nuclear Information System (INIS)

Nyquist, J.E.; Doll, W.E.; Davis, R.K.; Hopkins, R.A.

1992-01-01

Analysis of seismic refraction data collected at a proposed site of the Advanced Neutron Source (ANS) Facility showed a strong correlation between surface and bedrock topography. By combining seismically determined bedrock elevation data with surface elevation data using cokriging, we were able to significantly improve our map of bedrock topography without collecting additional seismic data

Soil mechanics and analysis of soils overlying cavitose bedrock

International Nuclear Information System (INIS)

Drumm, E.C.

1987-08-01

The stability of the residual soils existing at the West Chestnut Ridge Site, Oak Ridge Reservation, Tennessee, was evaluated. The weathered bedrock below this residual soil contains numerous solution cavities, and several karst features were identified. The West Chestnut Ridge site was evaluated with respect to deformation and collapse of the residual soil into the bedrock cavities. A finite element analysis investigated the effects of bedrock cavity radius, thickness of soil overburden, and surface surcharge upon the deformational and stability characteristics of the residual soil. The results indicate that for small cavity radii, the thickness of the soil cover has little effect on the zone of yielded soil. For large cavity radii, a smaller zone of distressed soil occurs under thick soil cover than under thin soil cover. Dimensionless curves are presented to enable the prediction of the vertical extent of the zone of yielded soil for a range of site geometries. Although the thick soil deposits (100 feet or greater) typically found on the ridges result in high stresses adjacent to the cavity, the area of the distressed or yielded soil is small and unlikely to extend to the surface. In addition, the surface deformation or subsidence is expected to be minimal. Thus, the siting of waste facilities on the ridges where the overburden is maximum would tend to reduce the effects of deformation into the cavities. 29 refs., 37 figs., 7 tabs

Analysis of overdeepened valleys using the digital elevation model of the bedrock surface of Northern Switzerland

Energy Technology Data Exchange (ETDEWEB)

Jordan, P.

2010-11-15

Based on surface and borehole information, together with pre-existing regional and local interpretations, a 7,150 square kilometre Raster Digital Elevation Model (DEM) of the bedrock surface of northern Switzerland was constructed using a 25 m cell size. This model represents a further important step in the understanding of Quaternary sediment distribution and is open to a broad field of application and analysis, including hydrogeological, geotechnical and geophysical studies as well as research in the field of Pleistocene landscape evolution. An analysis of the overdeepened valleys in the whole model area and, more specifically in the Reuss area, shows that, in most cases, overdeepening is restricted to the areas covered by the Last Glaciation Maximum (LGM). However, at various locations relatively narrow overdeepened valleys outreach the tongue basins and the LGM ice shield limits. Therefore, an earlier and further-reaching glacial event has probably contributed significantly to the overdeepening of these valleys. No significant overdeepening has been identified downstream of Boettstein (Aare) and Kaiserstuhl (Rhine), although the ice extended considerably further downstream, at least during the most extensive glaciation. Except for the bedrock between Brugg and Boettstein, no overdeepened valleys are found significantly north of the outcrop of Mesozoic limestone of the Folded and Tabular Jura. A detailed analysis of the Reuss area shows that the Lake and Suhre valleys are separated from the Emmen-Gisikon Reuss valley basin by a significant bedrock barrier. The individual bedrock valleys are divided into several sub-basins, indicating a multiphase evolution of the valleys. Some of the swells or barriers separating the sub-basins coincide with known late LGM retreat stages. In the Suhre valley, an old fluvial valley floor with restricted overdeepened sections is documented. (author)

Alluvial cover controlling the width, slope and sinuosity of bedrock channels

Science.gov (United States)

Turowski, Jens Martin

2018-02-01

Bedrock channel slope and width are important parameters for setting bedload transport capacity and for stream-profile inversion to obtain tectonics information. Channel width and slope development are closely related to the problem of bedrock channel sinuosity. It is therefore likely that observations on bedrock channel meandering yields insights into the development of channel width and slope. Active meandering occurs when the bedrock channel walls are eroded, which also drives channel widening. Further, for a given drop in elevation, the more sinuous a channel is, the lower is its channel bed slope in comparison to a straight channel. It can thus be expected that studies of bedrock channel meandering give insights into width and slope adjustment and vice versa. The mechanisms by which bedrock channels actively meander have been debated since the beginning of modern geomorphic research in the 19th century, but a final consensus has not been reached. It has long been argued that whether a bedrock channel meanders actively or not is determined by the availability of sediment relative to transport capacity, a notion that has also been demonstrated in laboratory experiments. Here, this idea is taken up by postulating that the rate of change of both width and sinuosity over time is dependent on bed cover only. Based on the physics of erosion by bedload impacts, a scaling argument is developed to link bedrock channel width, slope and sinuosity to sediment supply, discharge and erodibility. This simple model built on sediment-flux-driven bedrock erosion concepts yields the observed scaling relationships of channel width and slope with discharge and erosion rate. Further, it explains why sinuosity evolves to a steady-state value and predicts the observed relations between sinuosity, erodibility and storm frequency, as has been observed for meandering bedrock rivers on Pacific Arc islands.

Alluvial cover controlling the width, slope and sinuosity of bedrock channels

Directory of Open Access Journals (Sweden)

J. M. Turowski

2018-02-01

Full Text Available Bedrock channel slope and width are important parameters for setting bedload transport capacity and for stream-profile inversion to obtain tectonics information. Channel width and slope development are closely related to the problem of bedrock channel sinuosity. It is therefore likely that observations on bedrock channel meandering yields insights into the development of channel width and slope. Active meandering occurs when the bedrock channel walls are eroded, which also drives channel widening. Further, for a given drop in elevation, the more sinuous a channel is, the lower is its channel bed slope in comparison to a straight channel. It can thus be expected that studies of bedrock channel meandering give insights into width and slope adjustment and vice versa. The mechanisms by which bedrock channels actively meander have been debated since the beginning of modern geomorphic research in the 19th century, but a final consensus has not been reached. It has long been argued that whether a bedrock channel meanders actively or not is determined by the availability of sediment relative to transport capacity, a notion that has also been demonstrated in laboratory experiments. Here, this idea is taken up by postulating that the rate of change of both width and sinuosity over time is dependent on bed cover only. Based on the physics of erosion by bedload impacts, a scaling argument is developed to link bedrock channel width, slope and sinuosity to sediment supply, discharge and erodibility. This simple model built on sediment-flux-driven bedrock erosion concepts yields the observed scaling relationships of channel width and slope with discharge and erosion rate. Further, it explains why sinuosity evolves to a steady-state value and predicts the observed relations between sinuosity, erodibility and storm frequency, as has been observed for meandering bedrock rivers on Pacific Arc islands.

Surveying glacier bedrock topography with a helicopter-borne dual-polarization ground-penetrating radar system

Science.gov (United States)

Langhammer, L.; Rabenstein, L.; Schmid, L.; Bauder, A.; Schaer, P.; Maurer, H.

2017-12-01

Glacier mass estimations are crucial for future run-off projections in the Swiss Alps. Traditionally, ice thickness modeling approaches and ground-based radar transects have been the tools of choice for estimating glacier volume in high mountain areas, but these methods either contain high uncertainties or are logistically expensive and offer mostly only sparse subsurface information. We have developed a helicopter-borne dual-polarization ground-penetrating radar (GPR) system, which enhances operational feasibility in rough, high-elevation terrain and increases the data output per acquisition campaign significantly. Our system employs a prototype pulseEKKO device with two broadside 25-MHz antenna pairs fixed to a helicopter-towed wooden frame. Additionally attached to the system are a laser altimeter for measuring the flight height above ground, three GPS receivers for accurate positioning and a GoPro camera for obtaining visual images of the surface. Previous investigations have shown the significant impact of the antenna dipole orientation on the detectability of the bedrock reflection. For optimal results, the dipoles of the GPR should be aligned parallel to the strike direction of the surrounding mountain walls. In areas with a generally unknown bedrock topography, such as saddle areas or diverging zones, a dual-polarization system is particularly useful. This could be demonstrated with helicopter-borne GPR profiles acquired on more than 25 glaciers in the Swiss Alps. We observed significant differences in ice-bedrock interface visibility depending on the orientation of the antennas.

Bedrock geologic map of the Nashua South quadrangle, Hillsborough County, New Hampshire, and Middlesex County, Massachusetts

Science.gov (United States)

Walsh, Gregory J.; Jahns, Richard H.; Aleinikoff, John N.

2013-01-01

The bedrock geology of the 7.5-minute Nashua South quadrangle consists primarily of deformed Silurian metasedimentary rocks of the Berwick Formation. The metasedimentary rocks are intruded by a Late Silurian to Early Devonian diorite-gabbro suite, Devonian rocks of the Ayer Granodiorite, Devonian granitic rocks of the New Hampshire Plutonic Suite including pegmatite and the Chelmsford Granite, and Jurassic diabase dikes. The bedrock geology was mapped to study the tectonic history of the area and to provide a framework for ongoing hydrogeologic characterization of the fractured bedrock of Massachusetts and New Hampshire. This report presents mapping by G.J. Walsh and R.H. Jahns and zircon U-Pb geochronology by J.N. Aleinikoff. The complete report consists of a map, text pamphlet, and GIS database. The map and text pamphlet are only available as downloadable files (see frame at right). The GIS database is available for download in ESRITM shapefile and Google EarthTM formats, and includes contacts of bedrock geologic units, faults, outcrops, structural geologic information, photographs, and a three-dimensional model.

River longitudinal profiles and bedrock incision models: Stream power and the influence of sediment supply

Science.gov (United States)

Sklar, Leonard; Dietrich, William E.

The simplicity and apparent mechanistic basis of the stream power river incision law have led to its wide use in empirical and theoretical studies. Here we identify constraints on its calibration and application, and present a mechanistic theory for the effects of sediment supply on incision rates which spotlights additional limitations on the applicability of the stream power law. On channels steeper than about 20%, incision is probably dominated by episodic debris flows, and on sufficiently gentle slopes, sediment may bury the bedrock and prevent erosion. These two limits bound the application of the stream power law and strongly constrain the possible combination of parameters in the law. In order to avoid infinite slopes at the drainage divide in numerical models of river profiles using the stream power law it is commonly assumed that the first grid cell is unchanneled. We show, however, that the size of the grid may strongly influence the calculated equilibrium relief. Analysis of slope-drainage area relationships for a river network in a Northern California watershed using digital elevation data and review of data previously reported by Hack reveal that non-equilibrium profiles may produce well defined slope-area relationships (as expected in equilibrium channels), but large differences between tributaries may point to disequilibrium conditions. To explore the role of variations in sediment supply and transport capacity in bedrock incision we introduce a mechanistic model for abrasion of bedrock by saltating bedload. The model predicts that incision rates reach a maximum at intermediate levels of sediment supply and transport capacity. Incision rates decline away from the maximum with either decreasing supply (due to a shortage of tools) or increasing supply (due to gradual bed alluviation), and with either decreasing transport capacity (due to less energetic particle movement) or increasing transport capacity (due less frequent particle impacts per unit bed

Ultramafic-derived arsenic in a fractured bedrock aquifer

International Nuclear Information System (INIS)

Ryan, Peter C.; Kim, Jonathan; Wall, Andrew J.; Moen, Jonathan C.; Corenthal, Lilly G.; Chow, Daniel R.; Sullivan, Colleen M.; Bright, Kevin S.

2011-01-01

Highlights: → Arsenic is elevated in groundwater from a fractured bedrock aquifer system in northern Vermont, USA. → The arsenic source is serpentinized ultramafic rock. → Antigorite, magnetite (MgCO 3 ) and magnetite (Fe 3 O 4 ) appear to be the main mineralogical hosts of arsenic in the ultramafic rock. → Arsenic appears to be introduced to the ultramafic rock when As-bearing fluids are driven out of sediments during subduction. → The occurrence of serpentinized ultramafic rocks in many orogenic belts suggests that similar arsenic anomalies may occur in geologically-similar terranes globally. - Abstract: In the fractured bedrock aquifer of northern Vermont, USA, As concentrations in groundwater range from 3 ) with lesser amounts in magnetite (Fe 3 O 4 ). Hydrochemistry of monitoring wells drilled into fractured ultramafic rock in a groundwater recharge area with no anthropogenic As source reveals above background As (2-9 μg/L) and an Mg-HCO 3 hydrochemical signature that reflects dissolution of antigorite and magnesite, confirming that As in groundwater can be derived from ultramafic rock dissolution. Arsenic mobility in groundwater affected by ultramafic rock dissolution may be enhanced by alkaline pH values and relatively high HCO 3 - concentrations.

Determining the extent of groundwater interference on the performance of infiltration trenches

DEFF Research Database (Denmark)

Locatelli, Luca; Mark, Ole; Mikkelsen, Peter Steen

2015-01-01

Infiltration trenches are widely used in stormwater management, but their capacity decreases when installed in areas with shallow groundwater where infiltration is limited by groundwater drainage. Here the hydrological performance of single infiltration trenches in areas with shallow water tables...... is quantified in terms of their capability to reduce peak flow, peak volume and annual stormwater runoff volume. To simulate the long term hydrological performance of infiltration trenches two different models are employed. The models continuously simulate infiltration rates from infiltration trenches using...... to quantify the impact of parameter variability for each scenario. Statistical analysis of the continuous long term model simulations was used to quantify the hydrological performance of infiltration trenches. Results show that infiltration trenches are affected by groundwater when there is an unsaturated...

Determining the extent of groundwater interference on the performance of infiltration trenches

OpenAIRE

Locatelli, Luca; Mark, Ole; Mikkelsen, Peter Steen; Arnbjerg-Nielsen, Karsten; Wong, Tony; Binning, Philip John

2015-01-01

Infiltration trenches are widely used in stormwater management, but their capacity decreases when installed in areas with shallow groundwater where infiltration is limited by groundwater drainage. Here the hydrological performance of single infiltration trenches in areas with shallow water tables is quantified in terms of their capability to reduce peak flow, peak volume and annual stormwater runoff volume. To simulate the long term hydrological performance of infiltration trenches two differ...

The role of bedrock groundwater in rainfall-runoff response at hillslope and catchment scales

Science.gov (United States)

Gabrielli, C. P.; McDonnell, J. J.; Jarvis, W. T.

2012-07-01

SummaryBedrock groundwater dynamics in headwater catchments are poorly understood and poorly characterized. Direct hydrometric measurements have been limited due to the logistical challenges associated with drilling through hard rock in steep, remote and often roadless terrain. We used a new portable bedrock drilling system to explore bedrock groundwater dynamics aimed at quantifying bedrock groundwater contributions to hillslope flow and catchment runoff. We present results from the Maimai M8 research catchment in New Zealand and Watershed 10 (WS10) at the H.J. Andrews Experimental Forest in Oregon, USA. Analysis of bedrock groundwater at Maimai, through a range of flow conditions, revealed that the bedrock water table remained below the soil-bedrock interface, indicating that the bedrock aquifer has minimal direct contributions to event-based hillslope runoff. However, the bedrock water table did respond significantly to storm events indicating that there is a direct connection between hillslope processes and the underlying bedrock aquifer. WS10 groundwater dynamics were dominated by fracture flow. A highly fractured and transmissive zone within the upper one meter of bedrock conducted rapid lateral subsurface stormflow and lateral discharge. The interaction of subsurface stormflow with bedrock storage directly influenced the measured hillslope response, solute transport and computed mean residence time. This research reveals bedrock groundwater to be an extremely dynamic component of the hillslope hydrological system and our comparative analysis illustrates the potential range of hydrological and geological controls on runoff generation in headwater catchments.

VT Biodiversity Project - Bedrock Classification

Data.gov (United States)

Vermont Center for Geographic Information — (Link to Metadata) This dataset is a five category, nine sub-category classification of the bedrock units appearing on the Centennial Geologic Map of Vermont. The...

Urban Stormwater Infiltration Perspectives

DEFF Research Database (Denmark)

Geldof, Govert; Jacobsen, Per; Fujita, Shoichi

1994-01-01

In urban areas there are many problems with water management: combined sewer overflows, peak flows, man-induced droughts, consolidation of the soil, damage from frost penetration, etc. It is preferable to look at all these problems in relation to each other, according the concept of integrated...... water management. This paper focuses on the possibilities for urban stormwater infiltration. The results of three studies are presented. The first study concerns the flooding of the Shirako River in Tokyo. It is shown that with the help of stormwater infiltration the floods can be reduced remarkably....... The second study concerns combined sewer overflows and the discharge from treatment plants for catchments in Denmark and the Netherlands. When looking at the total yearly discharge from the combined sewer and the treatment plant, it is shown that infiltration is more effective than detention. The third study...

Burial and exhumation of temperate bedrock reefs as elucidated by repetitive high-resolution sea floor sonar surveys: Spatial patterns and impacts to species' richness and diversity

Science.gov (United States)

Storlazzi, Curt D.; Fregoso, Theresa A.; Figurski, Jared D.; Freiwald, Jan; Lonhart, Steve I.; Finlayson, David P.

2013-01-01

To understand how chronic sediment burial and scour contribute to variation in the structure of algal and invertebrate communities on temperate bedrock reefs, the dynamics of the substrate and communities were monitored at locations that experience sand inundation and adjacent areas that do not. Co-located benthic scuba-transect surveys and high-resolution swath-sonar surveys were completed on bedrock reefs on the inner shelf of northern Monterey Bay, CA, in early winter 2009, spring 2010, and summer 2010. Analysis of the sonar surveys demonstrates that during the 8 months over which the surveys were conducted, 19.6% of the study area was buried by sand while erosion resulted in the exposure of bedrock over 13.8% of the study area; the remainder underwent no change between the surveys. Substrate classifications from the benthic transect surveys correlated with classifications generated from the sonar surveys, demonstrating the capacity of high-resolution sonar surveys to detect burial of bedrock reefs by sediment. On bedrock habitat that underwent burial and exhumation, species' diversity and richness of rock-associated sessile and mobile organisms were 50–66% lower as compared to adjacent stable bedrock habitat. While intermediate levels of disturbance can increase the diversity and richness of communities, these findings demonstrate that burial and exhumation of bedrock habitat are sources of severe disturbance. We suggest that substrate dynamics must be considered when developing predictions of benthic community distributions based on sea floor imagery. These results highlight the need for predictive models of substrate dynamics and for a better understanding of how burial and exhumation shape benthic communities.

A review of published literature on the effects of permafrost on the hydrogeochemistry of bedrock

International Nuclear Information System (INIS)

Cascoyne, M.

2000-06-01

of seawater, enhanced or depleted sulphate concentrations in certain groundwaters, and lighter isotopic signature of the saline waters caused by the ice-water isotopic fractionation. This review has found that salt-rejection processes undoubtedly will have occurred in groundwaters in the marine sediments and bedrock of the Baltic coast during the Pleistocene. Deeply penetrating permafrost in the bedrock would cause relatively pure water to form as ice in fractures and displace residual saline fluids, under density flow, to greater depths. The process could have occurred to a sufficient extent that large volumes of saline water were generated, some of which may currently remain in the fractured rock. In these waters, loss of sulphate by mirabilite precipitation would be expected to have occurred but, on warming and degradation of the permafrost, lower-salinity meltwaters would re-dissolve the mirabilite, giving rise to a SO 4 -rich groundwater. This may be the origin of groundwater that is currently identified as Litorina Sea water at the Aespoe and Olkiluoto sites. This mechanism differs from that suggested by Israeli workers who propose freezing of open seawater and infiltration of residual brines into the bedrock followed by lateral migration inland. The hypothesis presented here, of formation of saline waters and brines by permafrost aggradation and salt-rejection is more acceptable from a hydrogeological standpoint because the saline waters are formed in situ and need not migrate laterally. Further field evidence, coupled with modelling of depths of permafrost penetration, could be used to assess the volume and concentration of saline groundwater formed as a result of downward advancement of permafrost in the crystalline bedrock. (orig.)

A review of published literature on the effects of permafrost on the hydrogeochemistry of bedrock

International Nuclear Information System (INIS)

Gascoyne, M.

2000-04-01

, enhanced or depleted sulphate concentrations in certain groundwaters, and lighter isotopic signature of the saline waters caused by the ice-water isotopic fractionation. This review has found that salt-rejection processes undoubtedly will have occurred in groundwaters in the marine sediments and bedrock of the Baltic coast during the Pleistocene. Deeply penetrating permafrost in the bedrock would cause relatively pure water to form as ice in fractures and displace residual saline fluids,under density flow, to greater depths. The process could have occurred to a sufficient extent that large volumes of saline water were generated, some of which may currently remain in the fractured rock. In these waters,loss of sulphate by mirabilite precipitation would be expected to have occurred but, on warming and degradation of the permafrost,lower-salinity meltwaters would re-dissolve the mirabilite, giving rise to a SO 4 -rich groundwater. This may be the origin of groundwater that is currently identified as Litorina Sea water at the Aespoe and Olkiluoto sites. This mechanism differs from that suggested by Israeli workers who propose freezing of open seawater and infiltration of residual brines into the bedrock followed by lateral migration inland. The hypothesis presented here, of formation of saline waters and brines by permafrost aggradation and salt-rejection is more acceptable from a hydrogeological standpoint because the saline waters are formed in situ and need not migrate laterally. Further field evidence, coupled with modelling of depths of permafrost penetration, could be used to assess the volume and concentration of saline groundwater formed as a result of downward advancement of permafrost in the crystalline bedrock

A review of published literature on the effects of permafrost on the hydrogeochemistry of bedrock

Energy Technology Data Exchange (ETDEWEB)

Gascoyne, M. [Gascoyne GeoProjects Inc., Pinawa (Canada)

2000-04-01

seawater, enhanced or depleted sulphate concentrations in certain groundwaters, and lighter isotopic signature of the saline waters caused by the ice-water isotopic fractionation. This review has found that salt-rejection processes undoubtedly will have occurred in groundwaters in the marine sediments and bedrock of the Baltic coast during the Pleistocene. Deeply penetrating permafrost in the bedrock would cause relatively pure water to form as ice in fractures and displace residual saline fluids,under density flow, to greater depths. The process could have occurred to a sufficient extent that large volumes of saline water were generated, some of which may currently remain in the fractured rock. In these waters,loss of sulphate by mirabilite precipitation would be expected to have occurred but, on warming and degradation of the permafrost,lower-salinity meltwaters would re-dissolve the mirabilite, giving rise to a SO{sub 4}-rich groundwater. This may be the origin of groundwater that is currently identified as Litorina Sea water at the Aespoe and Olkiluoto sites. This mechanism differs from that suggested by Israeli workers who propose freezing of open seawater and infiltration of residual brines into the bedrock followed by lateral migration inland. The hypothesis presented here, of formation of saline waters and brines by permafrost aggradation and salt-rejection is more acceptable from a hydrogeological standpoint because the saline waters are formed in situ and need not migrate laterally. Further field evidence, coupled with modelling of depths of permafrost penetration, could be used to assess the volume and concentration of saline groundwater formed as a result of downward advancement of permafrost in the crystalline bedrock.

A review of published literature on the effects of permafrost on the hydrogeochemistry of bedrock

Energy Technology Data Exchange (ETDEWEB)

Cascoyne, M. [Gascoyne GeoProjects Inc. (Canada)

2000-06-01

formed on freezing of seawater, enhanced or depleted sulphate concentrations in certain groundwaters, and lighter isotopic signature of the saline waters caused by the ice-water isotopic fractionation. This review has found that salt-rejection processes undoubtedly will have occurred in groundwaters in the marine sediments and bedrock of the Baltic coast during the Pleistocene. Deeply penetrating permafrost in the bedrock would cause relatively pure water to form as ice in fractures and displace residual saline fluids, under density flow, to greater depths. The process could have occurred to a sufficient extent that large volumes of saline water were generated, some of which may currently remain in the fractured rock. In these waters, loss of sulphate by mirabilite precipitation would be expected to have occurred but, on warming and degradation of the permafrost, lower-salinity meltwaters would re-dissolve the mirabilite, giving rise to a SO{sub 4}-rich groundwater. This may be the origin of groundwater that is currently identified as Litorina Sea water at the Aespoe and Olkiluoto sites. This mechanism differs from that suggested by Israeli workers who propose freezing of open seawater and infiltration of residual brines into the bedrock followed by lateral migration inland. The hypothesis presented here, of formation of saline waters and brines by permafrost aggradation and salt-rejection is more acceptable from a hydrogeological standpoint because the saline waters are formed in situ and need not migrate laterally. Further field evidence, coupled with modelling of depths of permafrost penetration, could be used to assess the volume and concentration of saline groundwater formed as a result of downward advancement of permafrost in the crystalline bedrock. (orig.)

Sequestration of Sr-90 Subsurface Contamination in the Hanford 100-N Area by Surface Infiltration of a Ca-Citrate-Phosphate Solution

Energy Technology Data Exchange (ETDEWEB)

Szecsody, James E.; Rockhold, Mark L.; Oostrom, Martinus; Moore, R. C.; Burns, Carolyn A.; Williams, Mark D.; Zhong, Lirong; Fruchter, Jonathan S.; McKinley, James P.; Vermeul, Vincent R.; Covert, Matthew A.; Wietsma, Thomas W.; Breshears, Andrew T.; Garcia, Ben J.

2009-03-01

subsurface area. However, the use of real-time surface and cross-borehole geophysics can be used to track the infiltrating Ca-citrate-PO4 front so some adjustments can be made in the infiltration rate to precipitate apatite in desired zones. In addition, the reactive transport code used in this study with field scale physical parameters for sediments can be used to evaluate infiltration strategies along with preliminary water infiltration tests at field scale.

An inexpensive and portable drill rig for bedrock groundwater studies in headwater catchments

Science.gov (United States)

C. Gabrielli; J.J. McDonnell

2011-01-01

Bedrock groundwater dynamics in headwater catchments are poorly understood and poorly characterized. Here, we present an inexpensive and portable bedrock drilling system designed for use in remote locations. Our system is capable of drilling bedrock wells up to 11 m deep and 38 mm in diameter in a wide range of bedrock types. The drill consists of a lawn mower engine...

Hydrogeological bedrock inferred from electrical resistivity model in Taichung Basin, Taiwan

Science.gov (United States)

Chiang, C. W.; Chang, P. Y.; Chang, L. C.

2015-12-01

The four-year project of the study of groundwater hydrogeology and recharge model was indicated by Central Geological Survey, MOEA, Taiwan (R.O.C.) to evaluate recharge groundwater areas in Taiwan where included Taipei, Taichung Basins, Lanyang and Chianan Plains. The groundwater recharge models of Lanyang Plain and Taipei Basin have successfully been estimated in two years ago (2013-2014). The third year of the project integrates with geophysical, geochemistry, and hydrogeology models to estimate the groundwater recharge model in Taichung Basin region. Taichung Basin is mainly covered by Pre-Pleistocene of thick gravel, sandy and muddy sediment rocks within a joint alluvial fan, whereas the depth of the hydrological bedrock remains uncertain. Two electrical resistivity geophysical tools were carried out utilizing direct current resistivity and audio-magnetotelluric (AMT) explorations, which could ideally provide the depth resolutions from shallow to depth for evaluating the groundwater resources. The study has carried out 21 AMT stations in the southern Taichung Basin in order to delineate hydrological bedrock in the region. All the AMT stations were deployed about 24 hours and processed with remote reference technique to reduce culture noises. The quality of most stations shows acceptable in the area which two stations were excluded due to near-field source effect in the southwestern basin. The best depth resolution is identified in 500 meters for the model. The preliminary result shows that the depths of the bedrock gradually changes from southern ~20 m toward to ~400 m in central, and eastern ~20 m to 180 m in the western basin inferred from the AMT model. The investigation shows that AMT method could be a useful geophysical tool to enhance the groundwater recharge model estimation without dense loggings in the region.

Beyond Tree Throw: Wind, Water, Rock and the Mechanics of Tree-Driven Bedrock Physical Weathering

Science.gov (United States)

Marshall, J. A.; Anderson, R. S.; Dawson, T. E.; Dietrich, W. E.; Minear, J. T.

2017-12-01

Tree throw is often invoked as the dominant process in converting bedrock to soil and thus helping to build the Critical Zone (CZ). In addition, observations of tree roots lifting sidewalk slabs, occupying cracks, and prying slabs of rock from cliff faces have led to a general belief in the power of plant growth forces. These common observations have led to conceptual models with trees at the center of the soil genesis process. This is despite the observation that tree throw is rare in many forested settings, and a dearth of field measurements that quantify the magnitude of growth forces. While few trees blow down, every tree grows roots, inserting many tens of percent of its mass below ground. Yet we lack data quantifying the role of trees in both damaging bedrock and detaching it (and thus producing soil). By combing force measurements at the tree-bedrock interface with precipitation, solar radiation, wind speed, and wind-driven tree sway data we quantified the magnitude and frequency of tree-driven soil-production mechanisms from two contrasting climatic and lithologic regimes (Boulder and Eel Creek CZ Observatories). Preliminary data suggests that in settings with relatively thin soils, trees can damage and detach rock due to diurnal fluctuations, wind response and rainfall events. Surprisingly, our data suggests that forces from roots and trunks growing against bedrock are insufficient to pry rock apart or damage bedrock although much more work is needed in this area. The frequency, magnitude and style of wind-driven tree forces at the bedrock interface varies considerably from one to another species. This suggests that tree properties such as mass, elasticity, stiffness and branch structure determine whether trees respond to gusts big or small, move at the same frequency as large wind gusts, or are able to self-dampen near-ground sway response to extended wind forces. Our measurements of precipitation-driven and daily fluctuations in root pressures exerted on

On-site infiltration of road runoff using pervious pavements with subjacent infiltration trenches as source control strategy.

Science.gov (United States)

Fach, S; Dierkes, C

2011-01-01

The focus in this work was on subsoil infiltration of stormwater from parking lots. With regard to operation, reduced infiltration performance due to clogging and pollutants in seepage, which may contribute to contaminate groundwater, are of interest. The experimental investigation covered a pervious pavement with a subjacent infiltration trench draining an impervious area of 2 ha. In order to consider seasonal effects on the infiltration performance, the hydraulic conductivity was measured tri-monthly during monitoring with a mobile sprinkling unit. To assess natural deposits jointing, road bed, gravel of infiltration trenches and subsoil were analysed prior to commencement of monitoring for heavy metals, polycyclic aromatic and mineral oil type hydrocarbons. Furthermore, from 22 storm events, water samples of rainfall, surface runoff, seepage and ground water were analysed with regard to the above mentioned pollutants. The study showed that the material used for the joints had a major impact on the initial as well as the final infiltration rates. Due to its poor hydraulic conductivity, limestone gravel should not be used as jointing. Furthermore, it is recommended that materials for the infiltration facilities are ensured free of any contaminants prior to construction. Polycyclic aromatic and mineral oil type hydrocarbons were, with the exception of surface runoff, below detection limits. Heavy metal concentrations of groundwater were with the exception of lead (because of high background concentrations), below the permissible limits.

Qualification of some compounds for tracing waterflows in coastal bedrock: A preliminary study

International Nuclear Information System (INIS)

Bjoernstad, H.E.; Eriksen, D.Oe.; Gaut, S.; Storaa, G.

1999-01-01

At Holmedal, Western Norway, the Geological Survey of Norway runs a test area with nine drilled wells. The site is mainly used for testing hydrodynamical models of ground water flow in fractured bedrock. During a test of communications between the wells we were offered an opportunity to test and qualify compounds to be used as tracers in such environment

Experimental study of water fluxes in a residential area: 2. Road infiltration, runoff and evaporation

Science.gov (United States)

Ragab, R.; Rosier, P.; Dixon, A.; Bromley, J.; Cooper, J. D.

2003-08-01

Lack of accurate data has led some hydrologists and city planners to assume that urban infiltration is zero and runoff is 100% of the rainfall. These assumptions lead to an over estimation of road runoff volume and an underestimation of direct recharge to groundwater, which is already rising under some UK cities. This study investigates infiltration and runoff processes and quantifies the percentage of rainfall that contributes to storm drainage, and that which infiltrates through different types of road surface. Access tubes were installed for measuring soil water content using a neutron probe in three car parks, a road and a grass site at the Centre for Ecology and Hydrology, Crowmarsh Gifford, Wallingford. Storm drainage was recorded at the exit of the Thamesmead Estate in Crowmarsh Gifford, just before the drain joins the River Thames at Wallingford. Rainfall and water table depth were also recorded. Weekly measurements of soil moisture content indicated that the top 40 cm layer is not influenced by water-table fluctuations and, therefore, positive changes in soil moisture could be attributed to infiltration of rainfall through the surface. Depending on the nature of the surface, subsurface layers, level of traffic, etc., between 6 and 9% of rainfall was found to infiltrate through the road surfaces studied. The storm drainage generated by road runoff revealed a flow pattern similar to that of the receiving watercourse (River Thames) and increased with the increase of infiltration and soil water content below the road surface. The ratio of runoff to rainfall was 0·7, 0·9 and 0·5 for annual, winter (October-March) and summer (April-September) respectively. As the results of the infiltration indicated that 6 to 9% of annual rainfall infiltrates through the road surface, this means that evaporation represents, 21-24% of annual rainfall, with more evaporation taking place during summer than winter.

INFLUENCE OF SEDIMENT SUPPLY, LITHOLOGY, AND WOOD DEBRIS ON THE DISTRIBUTION OF BEDROCK AND ALLUVIAL CHANNELS

Science.gov (United States)

Field surveys in the Willapa River basin, Washington State, indicate that the drainage area?channel slope threshold describing the distribution of bedrock and alluvial channels is influenced by the underlying lithology and that local variations in sediment supply can overwhelm ba...

Digital bedrock geologic map of the Mount Snow & Readsboro quadrangles, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-DM1 Ratcliffe, NM, 1995, Digital bedrock geologic map of the Mount Snow & Readsboro quadrangles, Vermont, scale 1:24000, The bedrock...

Spatial and temporal infiltration dynamics during managed aquifer recharge.

Science.gov (United States)

Racz, Andrew J; Fisher, Andrew T; Schmidt, Calla M; Lockwood, Brian S; Los Huertos, Marc

2012-01-01

Natural groundwater recharge is inherently difficult to quantify and predict, largely because it comprises a series of processes that are spatially distributed and temporally variable. Infiltration ponds used for managed aquifer recharge (MAR) provide an opportunity to quantify recharge processes across multiple scales under semi-controlled conditions. We instrumented a 3-ha MAR infiltration pond to measure and compare infiltration patterns determined using whole-pond and point-specific methods. Whole-pond infiltration was determined by closing a transient water budget (accounting for inputs, outputs, and changes in storage), whereas point-specific infiltration rates were determined using heat as a tracer and time series analysis at eight locations in the base of the pond. Whole-pond infiltration, normalized for wetted area, rose rapidly to more than 1.0 m/d at the start of MAR operations (increasing as pond stage rose), was sustained at high rates for the next 40 d, and then decreased to less than 0.1 m/d by the end of the recharge season. Point-specific infiltration rates indicated high spatial and temporal variability, with the mean of measured values generally being lower than rates indicated by whole-pond calculations. Colocated measurements of head gradients within saturated soils below the pond were combined with infiltration rates to calculate soil hydraulic conductivity. Observations indicate a brief period of increasing saturated hydraulic conductivity, followed by a decrease of one to two orders of magnitude during the next 50 to 75 d. Locations indicating the most rapid infiltration shifted laterally during MAR operation, and we suggest that infiltration may function as a "variable source area" processes, conceptually similar to catchment runoff. © 2011, The Author(s). Ground Water © 2011, National Ground Water Association.

First measurement of ice-bedrock interface of alpine glaciers by cosmic muon radiography

Science.gov (United States)

Nishiyama, R.; Ariga, A.; Ariga, T.; Käser, S.; Lechmann, A.; Mair, D.; Scampoli, P.; Vladymyrov, M.; Ereditato, A.; Schlunegger, F.

2017-06-01

The shape of the bedrock underneath alpine glaciers bears vital information on the erosional mechanism related to the flow of ice. So far, several geophysical exploration methods have been proposed to map the bedrock topography though with limited accuracy. Here we illustrate the first results from a technology, called cosmic ray muon radiography, newly applied in glacial geology to investigate the bedrock geometry beneath the Aletsch Glacier situated in the Central Swiss Alps. For this purpose we installed new cosmic muon detectors made of emulsion films at three sites along the Jungfrau railway tunnel and measured the shape of the bedrock under the uppermost part of Aletsch Glacier (Jungfraufirn). Our results constrain the continuation of the bedrock-ice interface up to a depth of 50 m below the surface, where the bedrock underneath the glacier strikes NE-SW and dips at 45° ± 5°. This documents the first successful application of this technology to a glaciated environment.

Rate estimates for lateral bedrock erosion based on radiocarbon ages, Duck River, Tennessee

International Nuclear Information System (INIS)

Brakenridge, G.R.

1985-01-01

Rates of bedrock erosion in ingrown meandering rivers can be inferred from the location of buried relict flood-plain and river-bank surfaces, associated paleosols, and radiocarbon dates. Two independent methods are used to evaluate the long-term rates of limestone bedrock erosion by the Duck River. Radiocarbon dates on samples retrieved from buried Holocene flood-plain and bank surfaces indicate lateral migration of the river bank at average rates of 0.6-1.9 m/100 yr. Such rates agree with lateral bedrock cliff erosion rates of 0.5-1.4 m/100 yr, as determined from a comparison of late Pleistocene and modern bedrock cliff and terrace scarp positions. These results show that lateral bedrock erosion by this river could have occurred coevally with flood-plain and terrace formation and that the resulting evolution of valley meander bends carved into bedrock is similar in many respects to that of channel meanders cut into alluvium. 11 references, 5 figures

Water infiltration capacity under different land uses and agricultural management practices

Directory of Open Access Journals (Sweden)

Lizandra Poeta Teixeira

2009-08-01

Full Text Available Knowledge of physical and hydraulic properties of soil is important for the appropriate use and management of soil, and for the understanding of dynamic movement process of water and solutes. This study aims to determine the soil infiltration capacity of the Concordia Experimental Basin, located in the municipality of Lontras in Santa Catarina state. The infiltration tests were performed with the concentric ring infiltrometer, with a diameter of 25 and 50 cm on twenty sampling points showing different uses of land and agricultural management practices. The initial capacity of infiltration, calculated by Horton's equation, ranged from 0.8 (pasture to 5.0 cm min-1 (pine forest and cassava planting. In pasture areas, the initial infiltration ranged from 0.8 to 0.9 cm min-1. Regarding the minimum value, they ranged from 0.01 (perennial pasture to 0.3 cm min-1 (minimum tillage for corn. In forest areas, the minimum infiltration varied between 0.05 and 0.15 cm min-1 and in the areas of pasture, it was equal to 0.01 cm min-1.

Global distribution of bedrock exposures on Mars using THEMIS high-resolution thermal inertia

Science.gov (United States)

Edwards, C.S.; Bandfield, J.L.; Christensen, P.R.; Fergason, R.L.

2009-01-01

We investigate high thermal inertia surfaces using the Mars Odyssey Thermal Emission Imaging System (THEMIS) nighttime temperature images (100 m/pixel spatial sampling). For this study, we interpret any pixel in a THEMIS image with a thermal inertia over 1200 J m-2 K-1 s-1/2 as "bedrock" which represents either in situ rock exposures or rock-dominated surfaces. Three distinct morphologies, ranked from most to least common, are associated with these high thermal inertia surfaces: (1) valley and crater walls associated with mass wasting and high surface slope angles; (2) floors of craters with diameters >25 km and containing melt or volcanics associated with larger, high-energy impacts; and (3) intercrater surfaces with compositions significantly more mafic than the surrounding regolith. In general, bedrock instances on Mars occur as small exposures (less than several square kilometers) situated in lower-albedo (inertia (>350 J m-2 K-1 s-1/2), and relatively dust-free (dust cover index <0.95) regions; however, there are instances that do not follow these generalizations. Most instances are concentrated in the southern highlands, with very few located at high latitudes (poleward of 45oN and 58oS), suggesting enhanced mechanical breakdown probably associated with permafrost. Overall, Mars has very little exposed bedrock with only 960 instances identified from 75oS to 75oN with likely <3500 km2 exposed, representing???1% of the total surface area. These data indicate that Mars has likely undergone large-scale surface processing and reworking, both chemically and mechanically, either destroying or masking a majority of the bedrock exposures on the planet. Copyright 2009 by the American Geophysical Union.

Reversible fatty infiltration of the liver

International Nuclear Information System (INIS)

Bostel, F.; Hauger, W.

1987-01-01

Case studies show that acute pancreatitis occurring independently or combined with a preceding abuse of alcohol may be the cause of fatty infiltration of the liver. These fat areas can evolve in a very short time and provoke in the case of focal incidence diagnostic problems of differentiation against abscesses of metastases. Due to this fact and because of the rapid reversibility of the fatty infiltration under therapy, the safest method to clarify the situation consists of short-term CT controls. (orig.) [de

Constraining local subglacial bedrock erosion rates with cosmogenic nuclides

Science.gov (United States)

Wirsig, Christian; Ivy-Ochs, Susan; Christl, Marcus; Reitner, Jürgen; Reindl, Martin; Bichler, Mathias; Vockenhuber, Christof; Akcar, Naki; Schlüchter, Christian

2014-05-01

The constant buildup of cosmogenic nuclides, most prominently 10Be, in exposed rock surfaces is routinely employed for dating various landforms such as landslides or glacial moraines. One fundamental assumption is that no cosmogenic nuclides were initially present in the rock, before the event to be dated. In the context of glacially formed landscapes it is commonly assumed that subglacial erosion of at least a few meters of bedrock during the period of ice coverage is sufficient to remove any previously accumulated nuclides, since the production of 10Be ceases at a depth of 2-3 m. Insufficient subglacial erosion leads to overestimation of surface exposure ages. If the time since the retreat of the glacier is known, however, a discordant concentration of cosmogenic nuclides delivers information about the depth of subglacial erosion. Here we present data from proglacial bedrock at two sites in the Alps. Goldbergkees in the Hohe Tauern National Park in Austria and Gruebengletscher in the Grimsel Pass area in Switzerland. Samples were taken inside as well as outside of the glaciers' Little Ice Age extent. Measured nuclide concentrations are analyzed with the help of a MATLAB model simulating periods of exposure or glacial cover of user-definable length and erosion rates.

High-resolution monitoring of fluvial bedrock erosion in a natural gorge

Science.gov (United States)

Beer, Alexander R.; Turowski, Jens M.

2014-05-01

Morphological evolution of terrestrial and planetary landscapes is of increasing interest in the geosciences. In mountainous regions stream development and stream shape as a consequence of the interaction of uplift and erosion is fundamental for surface formation. Bedrock stream sections are prevalent that are routings for water and sediments. Hence, the correct description of bedrock channel evolution is fundamental for landscape modelling. To analyse how in situ erosion rates depend on factors like discharge, sediment transport and topography, there is a need of highly resolved topographic field data that so far is not available. Here we present preliminary outcomes of a change detection study from the Gorner Gorge above Zermatt, Switzerland. The outflow of the Gorner glacier (the Gornera stream) is captured most of the time by a water intake for hydropower production. However this intake is flushed twice a day in summer to purge settled sediments. Then the Gornera, charged with erosive bedload, runs along its natural stream bed that cuts through a roche moutonnée. This bedrock section (25m long, 5m wide and 8m deep) was surveyed repeatedly twice a year benefiting from nearly dry bed conditions during water capturing. A Leica ScanStation C10 was used for capturing high density point clouds (aspired average point spacing 5mm) of the bedrock surfaces. Referencing each of the various scanning positions was conducted using Leica HDS targets attached to fixed anchor bolts in the bedrock, that were surveyed locally with a total station. Resulting DEMs were used to calculate DEMs of difference (DoDs) for the bedrock walls and a huge boulder residing on the gravel bed. Erosion rates are visualised and discussed in respect of to the local spatial arrangement of the bedrock to the stream flow and water level.

Arsenic evolution in fractured bedrock wells in central Maine, USA

Science.gov (United States)

Yang, Q.; Zheng, Y.; Culbertson, C.; Schalk, C.; Nielsen, M. G.; Marvinney, R.

2010-12-01

Elevated arsenic concentration in fractured bedrock wells has emerged as an important and challenging health problem, especially in rural areas without public water supply and mandatory monitoring of private wells. This has posed risks of skin, bladder, prostate diseases and cancers to private well users. In central Maine, including the study site, 31% of bedrock wells in meta-sedimentary formations have been reported of elevated arsenic concentrations of > 10 µg/L. Geophysical logging and fracture specific water sampling in high arsenic wells have been conducted to understand how water flowing through the aquifers enters the boreholes and how arsenic evolves in the fracture bedrock wells. Two domestic wells in Manchester, Maine, located 50 meter apart with 38 µg/L and 73 µg/L of arsenic in unfiltered water, were investigated to characterize fractures by geophysical logging and to determine flow rates by pumping test. Water samples, representing the bore hole and the fractures, were collected and analyzed for arsenic under ambient and pumping conditions. Transmissivity of the fractures was estimated at 0.23-10.6 m2/day. Water with high dissolved arsenic was supplied primarily by high yielding fractures near the bottom of the borehole. Dissolved arsenic concentrations in borehole water increased as fracture water with high arsenic was replacing borehole water with initially low dissolved arsenic in response to pumping. The precipitation of iron particulates enriched in arsenic was common during and after pumping. Laboratory experiment on well water samples over a period of 16 days suggested that in the borehole arsenic was mainly settled with iron enriched particles, likely amorphous ferric oxyhydroxides, with possibly minor adsorption on the iron minerals. Another bedrock well in Litchfield, Maine, with 478 µg/L of arsenic in the unfiltered well water, is being investigated to quantify and reconstruct of the groundwater flow under ambient and pumping conditions

A modified risk evaluation method of slope failure in a heavy rain. For application to slopes in widespread area

International Nuclear Information System (INIS)

Suenaga, Hiroshi; Tanaka, Shiro; Kobayakawa, Hiroaki

2015-01-01

A risk evaluation method of slope failure has developed to combine gas-liquid two phase flow analysis as a rainfall infiltration analysis and elastic-plastic finite element analysis as a slope stability analysis and has applied to a slope field. This method, however, had a difficulty to apply to many slopes since it needed many parameters to calculate the risk of the slope failure. The method was simplified to lessen input parameters which included an inclination and length of a slope, a depth of bedrock and a rainfall pattern assuming that hydraulic properties and mechanical properties were similar for the same geological unit. The method was also modified to represent a water collection structure, a surface runoff, an existence of a forest road and a water level variation of a downward river / pond which could affect infiltration phenomena. Results of the simplification and the modification made it possible to enhance a prediction precision of the method and create a hazard map of slopes in widespread area. (author)

The glacially overdeepened trough of the Salzach Valley, Austria: Bedrock geometry and sedimentary fill of a major Alpine subglacial basin

Science.gov (United States)

Pomper, Johannes; Salcher, Bernhard C.; Eichkitz, Christoph; Prasicek, Günther; Lang, Andreas; Lindner, Martin; Götz, Joachim

2017-10-01

Overdeepened valleys are unambiguous features of glacially sculpted landscapes. They result from erosion at the bed of the glacier and their size and shape is determined by ice dynamics and the characteristics of the underlying bedrock. Major overdeepened valleys representing vertical bedrock erosion of several hundreds of meters are characteristic features of many trunk valleys in the formerly glaciated parts of the Alpine mountain belt. The thick sedimentary fill usually hinders attempts to unravel bedrock geometry, formation history and fill characteristics. Based on reflection seismic data and core-logs from multiple deep drillings we construct a detailed bedrock model of the Lower Salzach Valley trough, one of the largest overdeepened valleys in the European Alps. The analysed overdeepened structure characterized by a strongly undulating topography. Two reaches of enhanced erosion can be identified and are suggested to be related to variations in bedrock erodibility and a triple glacier confluence. The sedimentary fill shows clear characteristics of rapid infilling and subaqueous fan delta deposits indicate a strong influence of tributary streams. Associated surface lowering of the valley floor had a major impact on tributary stream incision but also on the available ice accumulation area at subsequent glaciations. The extent to which fills of earlier glaciations have been preserved from erosion during the last glacial maximum remains ambiguous and demands further exploration. To our knowledge the presented bedrock model is one of the best defined of any major overdeepened trunk valley.

Bedrock Hydrogeology-Site investigation SFR

International Nuclear Information System (INIS)

Oehman, Johan; Bockgaard, Niclas; Follin, Sven

2012-06-01

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations for a planned extension of the existing final repository for short-lived radioactive waste (SFR). This report presents an integrated analysis and interpretation of the historic data from the existing SFR (1980 - 1986), as well as, from the recent investigations for the planned extension of SFR (2008 - 2009). The primary objective is to establish a conceptual hydrogeological model of the bedrock for safety assessment and design analyses. Analyses and interpretations of all (old and new) hydraulic data are analysed with regard to the recently developed geological deformation zone model of the SFR model domain (Curtis et al. 2011). The methodology used by Curtis et al. (2011) has focussed on magnetic anomalies and deformation zone intercepts with ground surface greater than 300 m. In the hydrogeological modelling, however, it has been considered important to also explore the occurrence and characteristics of shallow horizontal to sub-horizontal structures (sheet joints) inside the SFR model domain. Such structures are of considerable importance for the hydrogeology in the uppermost c. 150 m of bedrock in SDM-Site Forsmark; hence the term Shallow Bedrock Aquifer was used to emphasise their hydraulic significance. In this study, the acronym SBA-structure is used for horizontal structures identified in the hydrogeological modelling. In addition to the predominantly steeply dipping geological deformation zones, eight so-called SBA-structures are modelled deterministically in the hydrogeological model. The SBA-structures are envisaged as hydraulically heterogeneous and composed of clusters of minor gently dipping to horizontal fractures rather than extensive single features. A type of structures that is partly included in the definition of the SBA-structures is the Unresolved Possible Deformations Zone (Unresolved PDZ) intercepts identified by Curtis et al. (2011). The Unresolved

Bedrock Hydrogeology - Site investigation SFR

Energy Technology Data Exchange (ETDEWEB)

Oehman, Johan [Geosigma AB, Stockholm (Sweden); Bockgaard, Niclas [Golder Assoes AB, Stockholm (Sweden); Follin, Sven [SF GeoLogic AB, Taeby (Sweden)

2012-06-15

The Swedish Nuclear Fuel and Waste Management Company (SKB) has conducted site investigations for a planned extension of the existing final repository for short-lived radioactive waste (SFR). This report presents an integrated analysis and interpretation of the historic data from the existing SFR (1980 - 1986), as well as, from the recent investigations for the planned extension of SFR (2008 - 2009). The primary objective is to establish a conceptual hydrogeological model of the bedrock for safety assessment and design analyses. Analyses and interpretations of all (old and new) hydraulic data are analysed with regard to the recently developed geological deformation zone model of the SFR model domain (Curtis et al. 2011). The methodology used by Curtis et al. (2011) has focussed on magnetic anomalies and deformation zone intercepts with ground surface greater than 300 m. In the hydrogeological modelling, however, it has been considered important to also explore the occurrence and characteristics of shallow horizontal to sub-horizontal structures (sheet joints) inside the SFR model domain. Such structures are of considerable importance for the hydrogeology in the uppermost c. 150 m of bedrock in SDM-Site Forsmark; hence the term Shallow Bedrock Aquifer was used to emphasise their hydraulic significance. In this study, the acronym SBA-structure is used for horizontal structures identified in the hydrogeological modelling. In addition to the predominantly steeply dipping geological deformation zones, eight so-called SBA-structures are modelled deterministically in the hydrogeological model. The SBA-structures are envisaged as hydraulically heterogeneous and composed of clusters of minor gently dipping to horizontal fractures rather than extensive single features. A type of structures that is partly included in the definition of the SBA-structures is the Unresolved Possible Deformations Zone (Unresolved PDZ) intercepts identified by Curtis et al. (2011). The Unresolved

Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

Energy Technology Data Exchange (ETDEWEB)

Laaksoharju, Marcus [Geopoint AB, Sollentuna (Sweden); Smellie, John [Conterra AB, Partille (Sweden); Tullborg, Eva-Lena [Terralogica, Graabo (Sweden); Gimeno, Maria [Univ. of Zaragoza, Zaragoza (Spain); Hallbeck, Lotta [Microbial Analytics, Goeteborg (Sweden); Molinero, Jorge [Amphos XXI Consulting S.L., Barcelona (Spain); Waber, Nick [Univ. of Bern, Bern (Switzerland)

2008-12-15

generally a high confidence in the description and understanding of the current spatial distribution of groundwater composition, mainly due to the consistency between different analyses and modelling of the chemical data, but also due to the agreement with the hydrogeological understanding of the area. The existence of a near-surface redox reaction zone appears to be plausible, but this is still unclear from uncertainties in data interpretation. Nevertheless, the abundance of calcite suggests there is active buffering capacity on dilute groundwaters low in calcite. Furthermore, even though quantification of the bedrock buffering capacity is not yet achieved, general indications from the Forsmark area as a whole point to a bedrock which has a sufficiently large buffering capacity to maintain pH values in the range 7 to 8.5 and Eh values lower than -140 mV. One important remaining uncertainty concerns the increase in sulphide concentrations measured in the on-going monitoring programme. Initial drilling and pumping may have disturbed the system or may have facilitated sulphate reduction, but this issue remains to be resolved. The monitoring programme will also support the overall understanding of the long term behaviour of other groundwater parameters such as uranium, DOC (dissolved organic carbon) and tritium

Bedrock hydrogeochemistry Forsmark. Site descriptive modelling SDM-Site Forsmark

International Nuclear Information System (INIS)

Laaksoharju, Marcus; Smellie, John; Tullborg, Eva-Lena; Gimeno, Maria; Hallbeck, Lotta; Molinero, Jorge; Waber, Nick

2008-12-01

generally a high confidence in the description and understanding of the current spatial distribution of groundwater composition, mainly due to the consistency between different analyses and modelling of the chemical data, but also due to the agreement with the hydrogeological understanding of the area. The existence of a near-surface redox reaction zone appears to be plausible, but this is still unclear from uncertainties in data interpretation. Nevertheless, the abundance of calcite suggests there is active buffering capacity on dilute groundwaters low in calcite. Furthermore, even though quantification of the bedrock buffering capacity is not yet achieved, general indications from the Forsmark area as a whole point to a bedrock which has a sufficiently large buffering capacity to maintain pH values in the range 7 to 8.5 and Eh values lower than -140 mV. One important remaining uncertainty concerns the increase in sulphide concentrations measured in the on-going monitoring programme. Initial drilling and pumping may have disturbed the system or may have facilitated sulphate reduction, but this issue remains to be resolved. The monitoring programme will also support the overall understanding of the long term behaviour of other groundwater parameters such as uranium, DOC (dissolved organic carbon) and tritium

Hydrochemistry of the Mahomet Bedrock Valley Aquifer, East-Central Illinois: indicators of recharge and ground-water flow

Science.gov (United States)

Panno, S.V.; Hackley, Keith C.; Cartwright, K.; Liu, Chao-Li

1994-01-01

recharge in this area is from bedrock. Concentrations of Na+, HCO3-, As, and TDS also increase in the western MVA. Ground water in the MAK is of a Ca2+-HCO3- type. Mass-balance calculations, using Cl- as a natural, conservative tracer, indicate that approximately 17% of the ground water flowing from the confluence area is derived from the MVA.

LOW COST POTENTIAL INFILTRATION ESTIMATION FOR WET TROPICAL WATERSHEDS FOR TERRITORIAL PLANNING SUPPORT

Directory of Open Access Journals (Sweden)

Franciane Mendonça dos Santos

2016-01-01

Full Text Available This study was developed at Caçula stream watershed of Ilha Solteira (Brazil for potential infiltration estimation based on digital cartography. These methods aim at low-cost and quick analysis processes in order to support the territorial planning. The preliminary potential infiltration chart was produced using ArcHydro and pedological information of the study area. The curve-number method (Soil Conservation Service was used to determine the potential infiltration combining information related to landuse and soil types in the watershed. We also used a methodology that assumes being possible to evaluate potential infiltration of a watershed combining average annual rainfall, land-use and watershed natural attributes (geomorphology, geology and pedology. Results show that ArcHydro is efficient for a preliminary characterization because it shows flow accumulation areas, allowing higher potential of degradation areas in terms of floods, mass movement and erosion. As land-use classes have significant weight in Soil Conservation Service method assessing potential infiltration, this method allow us to evaluate how land-use changes affect water dynamic in the watershed. The propose based on natural environment attributes enables to determine the homologous infiltration areas based on a higher number of natural characteristics of the area, and thereby obtain a result that is closer to the local conditions and, consequently for degradation surface processes identification.

Double versus single cartridge of 4% articaine infiltration into the retro-molar area for lower third molar surgery.

Science.gov (United States)

Sawang, Kamonpun; Chaiyasamut, Teeranut; Kiattavornchareon, Sirichai; Pairuchvej, Verasak; Bhattarai, Bishwa Prakash; Wongsirichat, Natthamet

2017-06-01

There are no studies regarding 4% articaine infiltration injection into the retro-molar area for an impacted lower third molar (LITM) surgery. This study aimed to evaluate the efficacy of infiltration using 1.7 ml (single cartridge: SC) of 4% articaine versus 3.4 ml (double cartridges: DC) of 4% articaine with 1:100,000 epinephrine in LITM surgery. This study involved 30 healthy patients with symmetrical LITM. The patients were assigned to receive either a DC or SC of 4% articaine with 1:100,000 epinephrine as a local anesthetic for each operation. Onset, duration, profoundness, need for additional anesthetic administration, total volume of anesthetic used, vitality of the tooth, and pain score during operation were recorded. The DC of 4 % articaine had a significantly higher success rate (83.3%) than did the SC (53.3%; P molar region can be an alternative anesthetic for LITM surgery.

Infiltration SuDS Map

OpenAIRE

Dearden, Rachel

2012-01-01

Infiltration SuDS are sustainable drainage systems (SuDS) that allow surface water to infiltrate to the ground. Examples include soakaways, infiltration basins, infiltration trenches and permeable pavements. Before planning to install Infiltration SuDS, the suitability of the ground should be assessed. The British Geological Survey has developed a bespoke Infiltration SuDS Map that enables a preliminary assessment of the suitability of the ground for infiltration SuDS. Th...

Bedrock Geologic Map of Vermont - Dikes

Data.gov (United States)

Vermont Center for Geographic Information — The bedrock geology was last mapped at a statewide scale 50 years ago at a scale of 1:250,000 (Doll and others, 1961). The 1961 map was compiled from 1:62,500-scale...

Bedrock Geologic Map of Vermont - Units

Data.gov (United States)

Vermont Center for Geographic Information — The bedrock geology was last mapped at a statewide scale 50 years ago at a scale of 1:250,000 (Doll and others, 1961). The 1961 map was compiled from 1:62,500-scale...

Sediment dynamics and the burial and exhumation of bedrock reefs along an emergent coastline as elucidated by repetitive sonar surveys: Northern Monterey Bay, CA

Science.gov (United States)

Storlazzi, C.D.; Fregoso, T.A.; Golden, N.E.; Finlayson, D.P.

2011-01-01

Two high-resolution bathymetric and acoustic backscatter sonar surveys were conducted along the energetic emergent inner shelf of northern Monterey Bay, CA, USA, in the fall of 2005 and the spring of 2006 to determine the impact of winter storm waves, beach erosion, and river floods on biologically-important siliclastic bedrock reef habitats. The surveys extended from water depths of 4 m to 22 m and covered an area of 3.14 km2, 45.8% of which was bedrock, gravel, and coarse-grained sand and 54.2% was fine-grained sand. Our analyses of the bathymetric and acoustic backscatter data demonstrates that during the 6 months between surveys, 11.4% of the study area was buried by fine-grained sand while erosion resulted in the exposure of bedrock or coarse-grained sand over 26.5% of the study area. The probability of burial decreased with increasing water depth and rugosity; the probability of exhumation increased with increasing wave-induced near-bed shear stress, seabed slope and rugosity. Much of the detected change was at the boundary between bedrock and unconsolidated sediment due to sedimentation and erosion burying or exhuming bedrock, respectively. In a number of cases, however, the change in seabed character was apparently due to changes in sediment grain size when scour exposed what appeared to be an underlying coarser-grained lag or the burial of coarser-grained sand and gravel by fine-grained sand. These findings suggest that, in some places, (a) burial and exhumation of nearshore bedrock reefs along rocky, energetic inner shelves occurs over seasonal timescales and appears related to intrinsic factors such as seabed morphology and extrinsic factors such as wave forces, and (b) single acoustic surveys typically employed for geologic characterization and/or habitat mapping may not adequately characterize the geomorphologic and sedimentologic nature of these types of environments that typify most of the Pacific Ocean and up to 50% of the world's coastlines.

The role of bedrock groundwater in rainfall-runoff response at hillslope and catchment scales

Science.gov (United States)

C. Gabrielli; J.J. McDonnell; W.T. Jarvis

2012-01-01

Bedrock groundwater dynamics in headwater catchments are poorly understood and poorly characterized. Direct hydrometric measurements have been limited due to the logistical challenges associated with drilling through hard rock in steep, remote and often roadless terrain. We used a new portable bedrock drilling system to explore bedrock groundwater dynamics aimed at...

Impact of stormwater infiltration basins on groundwater quality, Perth metropolitan region, Western Australia

Science.gov (United States)

Appleyard, S. J.

1993-08-01

Twelve bores were sunk adjacent to three stormwater infiltration basins in the Perth metropolitan area to examine the impact of runoff from a light industrial area, a medium-density residential area, and a major arterial road on groundwater quality, and to examine the hydrological response of the aquifer to runoff recharge. Automatic and manual water level monitoring between April and November 1990 indicated that groundwater levels responded within minutes to recharge from the infiltration basins. Peak water levels of up to 2.5 m above rest levels occurred 6 24 h after the commencement of ponding in the infiltration basins. There was a marked reduction in salinity and increase in dissolved oxygen concentrations in the upper part of the aquifer downgradient of the infiltration basins. Concentrations of toxic metals, nutrients, pesticides, and phenolic compounds in groundwater near the infiltration basins were low and generally well within Australian drinking water guidelines. However, sediment in the base of an infiltration basin draining a major road contained in excess of 3500 ppm of lead. Phthalates, which are US EPA priority pollutants, were detected in all but one bore near the infiltration basins. Their detection may be a sampling artifact, but they may also be derived from the plastic litter that accumulates in the infiltration basins. The concentration of iron in groundwater near the infiltration basins appears to be controlled by dissolved oxygen concentrations, with high iron concentrations occurring where dissolved oxygen concentrations are low. Pumping bores located near infiltration basins may suffer from iron encrustation problems caused by the mixing of shallow, oxygenated groundwater with water containing higher concentrations of iron from deeper in the aquifer.

Linking carbon and hydrologic fluxes in the critical zone: Observations from high-frequency monitoring of a weathered bedrock vadose zone

Science.gov (United States)

Tune, A. K.; Druhan, J. L.; Wang, J.; Cargill, S.; Murphy, C.; Rempe, D. M.

2017-12-01

A principle challenge in quantifying feedbacks between continental weathering and atmospheric CO2 is to improve understanding of how biogeochemical processes in the critical zone influence the distribution and mobility of organic and inorganic carbon. In particular, in landscapes characterized by thin soils and heterogeneous weathered and fractured bedrock, little data exist to inform and constrain predictive models for carbon dynamics. Here, we present the results of an intensive water and gas sampling campaign across an 18 m thick, variably saturated argillite weathering profile in the Eel River CZO. We monitor water content in situ and regularly collect samples of freely-draining water, tightly-held water, and gas through wet and dry seasons using a novel Vadose-zone Monitoring System (VMS) consisting of sensors and samplers distributed across a 20 m long inclined borehole. This novel approach facilitates the interception of gas and water during transport across the entire variably saturated weathering profile. The data demonstrate that seasonal changes in saturation control the vertical distribution and mobility of carbon in the fractured critical zone. Concentrations of gaseous CO2, O2, and dissolved organic and inorganic carbon fluctuate significantly and repeatably with seasonal additions of water infiltrating the weathered bedrock. A persistent vertical structure in the concentrations of dissolved phases and gas concentrations broadly corresponds to depths associated with unsaturated, seasonally saturated, and chronically saturated zones. Associated variations in the vertical structure of mineralogy and elemental composition, including solid phase organic carbon content, are observed in core obtained during drilling. Together, our observations indicate significant respiration of organic carbon at depths greater than the base of the soil, and thus motivate further investigation of the role of heterogeneous weathered, bedrock environments, which are needed to

Spatially variable rock erodibility in bedrock channels undergoing transient response to baselevel change, Great Falls area, Virginia

OpenAIRE

Shobe, Charles; Kee, Connor; Hancock, Gregory

2018-01-01

This is a poster that was presented in April 2014 at the Geological Society of America southeastern section meeting in Blacksburg, VA, USA. The poster presents rock strength and roughness data from tributaries to the Potomac River in Virginia. Our data support the idea that bedrock channel erodibility is greater on the channel margins than at the thalweg, which we hypothesize to be the result of weathering damage preferentially accumulated on the channel banks. This work was published in Shob...

VTT test borehole for bedrock investigations

International Nuclear Information System (INIS)

Okko, O.; Hassinen, P.; Front, K.

1994-02-01

A borehole of depth 150 m and diameter 56 mm has been drilled in the area adjacent to the premises of the Technical Research Centre of Finland (VTT) at Otaniemi, Espoo, for the purposes of calibrating geophysical measurements devices. This report presents the test results obtained so far and illustrates the processing of these, in which the various measurements are plotted as curves and combinations of curves. The interpretations provided so far consists of analyses of lithological variations, bedrock fracturing, the nature and occurrence of fracture zones and groundwater flow patterns. Samples were taken from those parts of the core shown by the borehole measurements to be homogenous and thin sections made from these for mineralogical determinations. The rock mechanical and petrophysical properties of the same points were examined. The core is in the possession of VTT, and the hole itself is available to outsiders for the calibration and testing of borehole measurement equipment. (orig.). (21 refs., 13 figs., 5 tabs.)

Fate of individual sewage disposal system wastewater within regolith in mountainous terrain

Science.gov (United States)

Dano, Kathleen; Poeter, Eileen; Thyne, Geoff

2008-06-01

In order to improve understanding of the fate of septic tank or individual sewage disposal system (ISDS) effluent in regolith overlying fractured-rock aquifers, effluent from an ISDS in such a setting was tracked via geophysical, hydrological, and geochemical methods. Under typical precipitation conditions, the effluent entered the fractured bedrock within 5 m of the boundary of the constructed infiltration area. During a period of unusually high spring recharge, the plume migrated between 50 and 100 m within the regolith before infiltrating the fractured bedrock. The chemical signature of the effluent is similar to that required to account for the decline in water quality, suggesting a causative relationship (as estimated from mass-balance models of the surface-water chemistry near the mouth of the basin). The elevated salt content of the effluent during periods of high natural recharge to the infiltration area correlates with elevated salt concentrations in surface and groundwater at the basin scale, suggesting that some of the effluent salt load may be stored in the unsaturated zone during dry periods and flushed during periods of elevated natural recharge.

Water flow in bedrock; estimation of influence of transmissive shaft and borehole

International Nuclear Information System (INIS)

Andersson, L.; Neretnieks, J.; Rasmuson, A.

1983-01-01

The bedrock, a system of large and small fractures that permit water transport through the rock mass. The water content of the bedrock can, under varying hydrostatic pressure conditions, give rise to different flow patterns via boreholes or shafts drilled through the rock. A case is dealt with where a borehole connects a low point in the terrain with a point in the repository where the hydrostatic pressure is higher than at the mouth of the borehole. The situation may be conceived as having arisen when the area was investigated and a hole was drilled at an angle down from the valley to a point below the high point in the area. If the borehole is not sealed, an artesian well may be created. The conductivity used, 2 times 10- 9 m/s, presumes that the repository has been emplaced in average quality rock at this depth. In reality, the repository site will be selected where the rock is better than average. In reality, a shaft - even if it is imperfectly backfilled - or a borehole exerts a flow resistance that reduces the available pressure difference at a depth of 500 m. Taken together, these factors indicate that approx. 5 m 3 /(year, 5 m) is the water flow that can be expected to emerge from the repository through a shaft or a borehole. Only this flow can have been contaminated with escaping substances from the repository area. Water that flows in from other parts of the hole dilutes this flow considerably. (G.B.)

Nitrate distribution and potential attenuation mechanisms of a municipal water supply bedrock aquifer

International Nuclear Information System (INIS)

Opazo, Tomás; Aravena, Ramón; Parker, Beth

2016-01-01

The Silurian bedrock aquifer constitutes a major aquifer system for groundwater supply across the Ontario province in Canada. The application of natural and industrial fertilizers near urban centers has led to groundwater NO_3"−-N concentrations that sometimes have exceeded the drinking water limit, posing a threat to the usage of groundwater for the human consumption. Therefore, there is a growing interest and concern about how nitrate is being leached, transported and potentially attenuated in bedrock aquifers. This study assesses the local distribution of groundwater NO_3"− in the up-gradient area of two historically impacted municipal wells, called Carter Wells, in the City of Guelph, Canada, in order to evaluate the potential nitrate attenuation mechanisms, using both groundwater geochemical and isotopic analysis ("3H, δ"1"5N-NO_3, δ"1"8O-NO_3, δ"1"8O-SO_4, δ"3"4S-SO_4) and a detailed vertical hydrogeological and geochemical bedrock characterization. The results indicate that probably the main source of nitrate to the Carter Wells is the up-gradient Arkell Research Station (ARS), an agricultural research facility where manure has been historically applied. The overburden and bedrock groundwater with high NO_3 concentrations at the ARS exhibits a manure-related δ"1"5N and δ"1"8O signature, isotopically similar to the high nitrate in the down-gradient groundwater from domestic wells and from the Carter Wells. The nitrate spatial distribution appears to be influenced and controlled by the geology, in which more permeable rock is found in the Guelph Formation which in turn is related to most of the high NO_3"− groundwater. The presence of an underlying low permeability Eramosa Formation favors the development of oxygen-depleted conditions, a key factor for the occurrence of denitrification. Groundwater with low NO_3"−-N concentrations associated with more oxygen-limited conditions and coincident with high SO_4"2"− concentrations are related to more

Aquifer recharge with stormwater runoff in urban areas: Influence of vadose zone thickness on nutrient and bacterial transfers from the surface of infiltration basins to groundwater.

Science.gov (United States)

Voisin, Jérémy; Cournoyer, Benoit; Vienney, Antonin; Mermillod-Blondin, Florian

2018-05-16

Stormwater infiltration systems (SIS) have been built in urban areas to reduce the environmental impacts of stormwater runoff. Infiltration basins allow the transfer of stormwater runoff to aquifers but their abilities to retain contaminants depend on vadose zone properties. This study assessed the influence of vadose zone thickness (VZT) on the transfer of inorganic nutrients (PO 4 3- , NO 3 - , NH 4 + ), dissolved organic carbon (total -DOC- and biodegradable -BDOC-) and bacteria. A field experiment was conducted on three SIS with a thin vadose zone (zone (>10 m). Water samples were collected at three times during a rainy period of 10 days in each infiltration basin (stormwater runoff), in the aquifer impacted by infiltration (impacted groundwater) and in the same aquifer but upstream of the infiltration area (non-impacted groundwater). Inorganic nutrients, organic matter, and dissolved oxygen (DO) were measured on all water samples. Bacterial community structures were investigated on water samples through a next-generation sequencing (NGS) scheme of 16S rRNA gene amplicons (V5-V6). The concentrations of DO and phosphate measured in SIS-impacted groundwaters were significantly influenced by VZT due to distinct biogeochemical processes occurring in the vadose zone. DOC and BDOC were efficiently retained in the vadose zone, regardless of its thickness. Bacterial transfers to the aquifer were overall low, but data obtained on day 10 indicated a significant bacterial transfer in SIS with a thin vadose zone. Water transit time and water saturation of the vadose zone were found important parameters for bacterial transfers. Most bacterial taxa (>60%) from impacted groundwaters were not detected in stormwater runoff and in non-impacted groundwaters, indicating that groundwater bacterial communities were significantly modified by processes associated with infiltration (remobilization of bacteria from vadose zone and/or species sorting). Copyright © 2018 Elsevier B

Depth to Bedrock: Isopach of Unconsolidated Materials

Data.gov (United States)

Iowa State University GIS Support and Research Facility — This vector dataset gives the approximate depth to bedrock (in feet) from Iowa's current land surface. This 50 foot isopach data was derived from the Digital...

Ground-water hydrology and glacial geology of the Kalamazoo area, Michigan

Science.gov (United States)

Deutsch, Morris; Vanlier, K.E.; Giroux, P.R.

1960-01-01

The Kalamazoo report area includes about 150 square miles of Kalamazoo County, Mich. The area is principally one of industry and commerce, although agriculture also is of considerable importance. It has a moderate and humid climate and lies within the Lake Michigan “snow belt”. Precipitation averages about 35 inches per year. Snowfall averages about 55 inches. The surface features of the area were formed during and since the glacial epoch and are classified as outwash plain, morainal highlands, and glaciated channels or drainageways. The area is formed largely on the remnants of an extensive outwash plain, which is breached by the Kalamazoo River in the northeastern part and is dissected elsewhere by several small tributaries to the river. Most of the land drained by these tributaries lies within the report area. A small portion of the southern part drains to the St. Joseph River. The Coldwater shale, which underlies the glacial deposits throughout the area, and the deeper bedrock formations are not tapped for water by wells and they have little or no potential for future development. Deposits of glacial drift, which are the source of water to all the wells in the area, have considerable potential for future development. These deposits range in thickness from about 40 feet along the Kalamazoo River to 350 feet where valleys were eroded in the bedrock surface. Permeable outwash and channel deposits are the sources of water for wells of large capacity. The moraines are formed dominantly by till of lower permeability which generally yields small supplies of water, but included sand and gravel beds of higher permeability yield larger supplies locally. The aquifers of the Kalamazoo area are recharged by infiltration of rainfall and snowmelt and by infiltration of surface waters induced by pumping of wells near the surface sources. Water pumped from most of the municipal well fields is replenished in part by such induced infiltration. Many of the industrial wells

[Effect of irregular bedrock topography on the soil profile pattern of water content in a Karst hillslope.

Science.gov (United States)

Jia, Jin Tian; Fu, Zhi Yong; Chen, Hong Song; Wang, Ke Lin; Zhou, Wei Jun

2016-06-01

Based on three manually excavated trenches (projection length of 21 m, width of 1 m) along a typical Karst hillslope, the changing trends for soil-bedrock structure, average water content of soil profile and soil-bedrock interface water content along each individual trench were studied. The effect of irregular bedrock topography on soil moisture distribution was discussed. The results showed that the surface topography was inconsistent with the bedrock topography in the Karst hill-slopes. The bedrock topography was highly irregular with a maximum variation coefficient of 82%. The distribution pattern of soil profile of moisture was significantly affected by the underlying undulant bedrock. The soil water content was related to slope position when the fluctuation was gentle, and displayed a linear increase from upslope to downslope. When the bedrock fluctuation increased, the downslope linear increasing trend for soil water content became unapparent, and the spatial continuity of soil moisture was weakened. The soil moisture was converged in rock dents and cracks. The average water content of soil profile was significantly positively correlated with the soil-bedrock interface water content, while the latter responded more sensitively to the bedrock fluctuation.

Analysis of Factors that Influence Infiltration Rates using the HELP Model

International Nuclear Information System (INIS)

Dyer, J.; Shipmon, J.

2017-01-01

The Hydrologic Evaluation of Landfill Performance (HELP) model is used by Savannah River National Laboratory (SRNL) in conjunction with PORFLOW groundwater flow simulation software to make longterm predictions of the fate and transport of radionuclides in the environment at radiological waste sites. The work summarized in this report supports preparation of the planned 2018 Performance Assessment for the E-Area Low-Level Waste Facility (LLWF) at the Savannah River Site (SRS). More specifically, this project focused on conducting a sensitivity analysis of infiltration (i.e., the rate at which water travels vertically in soil) through the proposed E-Area LLWF closure cap. A sensitivity analysis was completed using HELP v3.95D to identify the cap design and material property parameters that most impact infiltration rates through the proposed closure cap for a 10,000-year simulation period. The results of the sensitivity analysis indicate that saturated hydraulic conductivity (Ksat) for select cap layers, precipitation rate, surface vegetation type, and geomembrane layer defect density are dominant factors limiting infiltration rate. Interestingly, calculated infiltration rates were substantially influenced by changes in the saturated hydraulic conductivity of the Upper Foundation and Lateral Drainage layers. For example, an order-of-magnitude decrease in Ksat for the Upper Foundation layer lowered the maximum infiltration rate from a base-case 11 inches per year to only two inches per year. Conversely, an order-of-magnitude increase in Ksat led to an increase in infiltration rate from 11 to 15 inches per year. This work and its results provide a framework for quantifying uncertainty in the radionuclide transport and dose models for the planned 2018 E-Area Performance Assessment. Future work will focus on the development of a nonlinear regression model for infiltration rate using Minitab 17® to facilitate execution of probabilistic simulations in the GoldSim® overall

Analysis of Factors that Influence Infiltration Rates using the HELP Model

Energy Technology Data Exchange (ETDEWEB)

Dyer, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Shipmon, J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2017-09-28

The Hydrologic Evaluation of Landfill Performance (HELP) model is used by Savannah River National Laboratory (SRNL) in conjunction with PORFLOW groundwater flow simulation software to make longterm predictions of the fate and transport of radionuclides in the environment at radiological waste sites. The work summarized in this report supports preparation of the planned 2018 Performance Assessment for the E-Area Low-Level Waste Facility (LLWF) at the Savannah River Site (SRS). More specifically, this project focused on conducting a sensitivity analysis of infiltration (i.e., the rate at which water travels vertically in soil) through the proposed E-Area LLWF closure cap. A sensitivity analysis was completed using HELP v3.95D to identify the cap design and material property parameters that most impact infiltration rates through the proposed closure cap for a 10,000-year simulation period. The results of the sensitivity analysis indicate that saturated hydraulic conductivity (Ksat) for select cap layers, precipitation rate, surface vegetation type, and geomembrane layer defect density are dominant factors limiting infiltration rate. Interestingly, calculated infiltration rates were substantially influenced by changes in the saturated hydraulic conductivity of the Upper Foundation and Lateral Drainage layers. For example, an order-of-magnitude decrease in Ksat for the Upper Foundation layer lowered the maximum infiltration rate from a base-case 11 inches per year to only two inches per year. Conversely, an order-of-magnitude increase in Ksat led to an increase in infiltration rate from 11 to 15 inches per year. This work and its results provide a framework for quantifying uncertainty in the radionuclide transport and dose models for the planned 2018 E-Area Performance Assessment. Future work will focus on the development of a nonlinear regression model for infiltration rate using Minitab 17® to facilitate execution of probabilistic simulations in the GoldSim® overall

Bedrock erosion by sliding wear in channelized granular flow

Science.gov (United States)

Hung, C. Y.; Stark, C. P.; Capart, H.; Smith, B.; Maia, H. T.; Li, L.; Reitz, M. D.

2014-12-01

Boundary forces generated by debris flows can be powerful enough to erode bedrock and cause considerable damage to infrastructure during runout. Bedrock wear can be separated into impact and sliding wear processes. Here we focus on sliding wear. We have conducted experiments with a 40-cm-diameter grainflow-generating rotating drum designed to simulate dry channelized debris flows. To generate sliding erosion, we placed a 20-cm-diameter bedrock plate axially on the back wall of the drum. The rotating drum was half filled with 2.3-mm-diameter grains, which formed a thin grain-avalanching layer with peak flow speed and depth close to the drum axis. The whole experimental apparatus was placed on a 100g-ton geotechnical centrifuge and, in order to scale up the stress level, spun to a range of effective gravity levels. Rates and patterns of erosion of the bedrock plate were mapped after each experiment using 3d micro-photogrammetry. High-speed video and particle tracking were employed to measure granular flow dynamics. The resulting data for granular velocities and flow geometry were used to estimate impulse exchanges and forces on the bedrock plate. To address some of the complexities of granular flow under variable gravity levels, we developed a continuum model framed around a GDR MiDi rheology. This model allowed us to scale up boundary forcing while maintaining the same granular flow regime, and helped us to understand important aspects of the flow dynamics including e.g. fluxes of momentum and kinetic energy. In order to understand the detailed processes of boundary forcing, we performed numerical simulations with a new contact dynamics model. This model confirmed key aspects of our continuum model and provided information on second-order behavior such as fluctuations in the forces acting on the wall. By combining these measurements and theoretical analyses, we have developed and calibrated a constitutive model for sliding wear that is a threshold function of

REDUCTION OF SOIL INFILTRATION AREA THANKS TO THE WASTEWATER SECONDARY TREATMENT FILTERS

Directory of Open Access Journals (Sweden)

Marcin Spychała

2016-05-01

Full Text Available The aim of the article was to determine the feasibility and advisability of the use of secondary filters applied before discharge of wastewater into the ground in the context of the fulfillment of the conditions of the current Regulation of the Minister of Environment of 18 November 2014 on the conditions to be met during the discharge of wastewater into the water or the ground and on substances particularly harmful to the aquatic environment. Due to expected in practice, an application and popularity, as compared variants, reactors having a very simple construction were used. The average values of removal of BOD5, COD and total suspended solids for three secondary filters technologies: biological trickling filter with natural ventilation, sand filter and nonwoven filter were compared. Additionally, as a fourth option a simple mathematical model has been presented. This model allows to estimate of BOD5 at the outflow from biological trickling filter and to verify the empirical data. Despite a large usefulness, it is rarely used in our country. It has been found the possibility of reduction of the infiltration area (surface area after reduction is 38–63% of the initial value due to the application of secondary filters. In the case of a high initial demand of the terrain area for drainage localization the benefit in costs resulting from the reduction (several thousand of PLN or may even significantly exceed the cost of buying and installing a cheap secondary filter. In addition, reduction the occupied area of the lot (in extreme cases up to 100 m2 by using the secondary filter allows to use the unoccupied space for other purposes, and thus gives additional economic advantage.

Bedrock Geologic Map of Charlotte,�Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG09-5 Gale, M., Kim, J., Earle, H., Clark, A., Smith, T., and Petersen, K., 2009, Bedrock Geologic Map of Charlotte, Vermont: VGS Open-File Report...

Seasonal variation of infiltration capacities of soils in western Oregon.

Science.gov (United States)

Michael G. Johnson; Robert L. Beschta

1981-01-01

Infiltration capacities were 50 percent greater during fall than during summer for forest soils of western Oregon. These results contrast with those measured in other studies. In forested areas, investigators should be aware of potentially large seasonal changes in infiltration capacities. Such seasonal changes may exceed effects due to applied treatments (logging,...

Developing and exploring a theory for the lateral erosion of bedrock channels for use in landscape evolution models

Directory of Open Access Journals (Sweden)

A. L. Langston

2018-01-01

Full Text Available Understanding how a bedrock river erodes its banks laterally is a frontier in geomorphology. Theories for the vertical incision of bedrock channels are widely implemented in the current generation of landscape evolution models. However, in general existing models do not seek to implement the lateral migration of bedrock channel walls. This is problematic, as modeling geomorphic processes such as terrace formation and hillslope–channel coupling depends on the accurate simulation of valley widening. We have developed and implemented a theory for the lateral migration of bedrock channel walls in a catchment-scale landscape evolution model. Two model formulations are presented, one representing the slow process of widening a bedrock canyon and the other representing undercutting, slumping, and rapid downstream sediment transport that occurs in softer bedrock. Model experiments were run with a range of values for bedrock erodibility and tendency towards transport- or detachment-limited behavior and varying magnitudes of sediment flux and water discharge in order to determine the role that each plays in the development of wide bedrock valleys. The results show that this simple, physics-based theory for the lateral erosion of bedrock channels produces bedrock valleys that are many times wider than the grid discretization scale. This theory for the lateral erosion of bedrock channel walls and the numerical implementation of the theory in a catchment-scale landscape evolution model is a significant first step towards understanding the factors that control the rates and spatial extent of wide bedrock valleys.

Developing and exploring a theory for the lateral erosion of bedrock channels for use in landscape evolution models

Science.gov (United States)

Langston, Abigail L.; Tucker, Gregory E.

2018-01-01

Understanding how a bedrock river erodes its banks laterally is a frontier in geomorphology. Theories for the vertical incision of bedrock channels are widely implemented in the current generation of landscape evolution models. However, in general existing models do not seek to implement the lateral migration of bedrock channel walls. This is problematic, as modeling geomorphic processes such as terrace formation and hillslope-channel coupling depends on the accurate simulation of valley widening. We have developed and implemented a theory for the lateral migration of bedrock channel walls in a catchment-scale landscape evolution model. Two model formulations are presented, one representing the slow process of widening a bedrock canyon and the other representing undercutting, slumping, and rapid downstream sediment transport that occurs in softer bedrock. Model experiments were run with a range of values for bedrock erodibility and tendency towards transport- or detachment-limited behavior and varying magnitudes of sediment flux and water discharge in order to determine the role that each plays in the development of wide bedrock valleys. The results show that this simple, physics-based theory for the lateral erosion of bedrock channels produces bedrock valleys that are many times wider than the grid discretization scale. This theory for the lateral erosion of bedrock channel walls and the numerical implementation of the theory in a catchment-scale landscape evolution model is a significant first step towards understanding the factors that control the rates and spatial extent of wide bedrock valleys.

Preliminary Bedrock Geologic Map of the Old Lyme Quadrangle, New London and Middlesex Counties, Connecticut

Science.gov (United States)

Walsh, Gregory J.; Scott, Robert B.; Aleinikoff, John N.; Armstrong, Thomas R.

2006-01-01

This report presents a preliminary map of the bedrock geology of the Old Lyme quadrangle, New London and Middlesex Counties, Connecticut. The map depicts contacts of bedrock geologic units, faults, outcrops, and structural geologic information. The map was published as part of a study of fractured bedrock aquifers and regional tectonics.

Application of a water balance model for estimating deep infiltration in a karstic watershed

Directory of Open Access Journals (Sweden)

Maria Lúcia Calijuri

2011-12-01

Full Text Available The current scenario of water scarcity evidences the need for an adequate management of water resources. In karstic regions, the water flow through fractures significantly increases the water infiltration rate, which explains the small number of rivers and the importance of groundwater for urban supply. Therefore, the water balance is necessary since it may aid decision making processes and guide water management projects. The objective of this paper was to perform the water balance of a watershed situated in a karstic region quantifying infiltration, runoff and evapotranspiration. The study area is located near the Tancredo Neves International Airport in Confins, in the state of Minas Gerais, Brazil. Most of the area consists of forest formations (40.9%, and pastures (34.5%. In order to estimate deep infiltration, the BALSEQ model was used. BALSEQ is a numeric model of sequential water balance in which deep infiltration at the end of the day is given by the difference between daily precipitation and the sum of surface runoff, evapotranspiration and the variation of the amount of water stored in the soil. The results show that approximately 60% of total annual precipitation result in deep infiltration, considering the recharge period from September to March. After the dry period, the areas with no vegetal cover present higher deep infiltration. However, over the months, the contribution of the vegetated areas becomes greater, showing the importance of these areas to aquifer recharge.

The origin and significance of sinuosity along incising bedrock rivers

Science.gov (United States)

Barbour, Jonathan Ross

Landscapes evolve through processes acting at the earth's surface in response to tectonics and climate. Rivers that cut into bedrock are particularly important since they set the local baselevel and communicate changes in boundary conditions across the landscape through erosion and deposition; the pace of topographic evolution depends on both the rate of change of the boundary conditions and the speed of the bedrock channel network response. Much of the work so far has considered the effects of tectonically-controlled changes in slope and climatically-controlled changes in discharges to the rate of channel bed erosion while considering bank erosion, if active at all, to be of at best secondary importance to landscape evolution. Sprinkled throughout the literature of the past century are studies that have recognized lateral activity along incising rivers, but conflicting interpretations have left many unanswered questions about how to identify and measure horizontal erosion, what drives it, what effect it has on the landscape, and how it responds to climate and tectonics. In this thesis, I begin to answer some of these questions by focusing on bedrock river sinuosity and its evolution through horizontal erosion of the channel banks. An analysis of synoptic scale topography and climatology of the islands of eastern Asia reveals a quantitative signature of storm frequency in a regional measure of mountain river sinuosity. This is partly explained through a study of the hydro- and morphodynamics of a rapidly evolving bedrock river in Taiwan which shows how the erosive forces vary along a river to influence the spatiotemporal distribution of downcutting, sidecutting, and sediment transport. Through these analyses, I also present evidence that suggests that the relative frequency of erosive events is far more important than the absolute magnitude of extreme events in setting the erosion rate, and I show that the horizontal erosion of bedrock rivers is an important

Synthesis of soil-hydraulic properties and infiltration timescales in wildfire-affected soils

Science.gov (United States)

Ebel, Brian A.; Moody, John A.

2017-01-01

We collected soil-hydraulic property data from the literature for wildfire-affected soils, ash, and unburned soils. These data were used to calculate metrics and timescales of hydrologic response related to infiltration and surface runoff generation. Sorptivity (S) and wetting front potential (Ψf) were significantly different (lower) in burned soils compared with unburned soils, whereas field-saturated hydraulic conductivity (Kfs) was not significantly different. The magnitude and duration of the influence of capillarity during infiltration was greatly reduced in burned soils, causing faster ponding times in response to rainfall. Ash had large values of S and Kfs but moderate values of Ψf, compared with unburned and burned soils, indicating ash has long ponding times in response to rainfall. The ratio of S2/Kfs was nearly constant (~100 mm) for unburned soils but more variable in burned soils, suggesting that unburned soils have a balance between gravity and capillarity contributions to infiltration that may depend on soil organic matter, whereas in burned soils the gravity contribution to infiltration is greater. Changes in S and Kfs in burned soils act synergistically to reduce infiltration and accelerate and amplify surface runoff generation. Synthesis of these findings identifies three key areas for future research. First, short timescales of capillary influences on infiltration indicate the need for better measurements of infiltration at times less than 1 min to accurately characterize S in burned soils. Second, using parameter values, such as Ψf, from unburned areas could produce substantial errors in hydrologic modeling when used without adjustment for wildfire effects, causing parameter compensation and resulting underestimation of Kfs. Third, more thorough measurement campaigns that capture soil-structural changes, organic matter impacts, quantitative water repellency trends, and soil-water content along with soil-hydraulic properties could drive the

Hazard Ranking Method for Populations Exposed to Arsenic in Private Water Supplies: Relation to Bedrock Geology.

Science.gov (United States)

Crabbe, Helen; Fletcher, Tony; Close, Rebecca; Watts, Michael J; Ander, E Louise; Smedley, Pauline L; Verlander, Neville Q; Gregory, Martin; Middleton, Daniel R S; Polya, David A; Studden, Mike; Leonardi, Giovanni S

2017-12-01

Approximately one million people in the UK are served by private water supplies (PWS) where main municipal water supply system connection is not practical or where PWS is the preferred option. Chronic exposure to contaminants in PWS may have adverse effects on health. South West England is an area with elevated arsenic concentrations in groundwater and over 9000 domestic dwellings here are supplied by PWS. There remains uncertainty as to the extent of the population exposed to arsenic (As), and the factors predicting such exposure. We describe a hazard assessment model based on simplified geology with the potential to predict exposure to As in PWS. Households with a recorded PWS in Cornwall were recruited to take part in a water sampling programme from 2011 to 2013. Bedrock geologies were aggregated and classified into nine Simplified Bedrock Geological Categories (SBGC), plus a cross-cutting "mineralized" area. PWS were sampled by random selection within SBGCs and some 508 households volunteered for the study. Transformations of the data were explored to estimate the distribution of As concentrations for PWS by SBGC. Using the distribution per SBGC, we predict the proportion of dwellings that would be affected by high concentrations and rank the geologies according to hazard. Within most SBGCs, As concentrations were found to have log-normal distributions. Across these areas, the proportion of dwellings predicted to have drinking water over the prescribed concentration value (PCV) for As ranged from 0% to 20%. From these results, a pilot predictive model was developed calculating the proportion of PWS above the PCV for As and hazard ranking supports local decision making and prioritization. With further development and testing, this can help local authorities predict the number of dwellings that might fail the PCV for As, based on bedrock geology. The model presented here for Cornwall could be applied in areas with similar geologies. Application of the method

Shallow reflection seismic soundings in bedrock at Lavia

International Nuclear Information System (INIS)

Okko, Olli

1988-03-01

The well-studied granitic block at Lavia was one of the test sites of a shallow seismic development project. A portable digital seismograph and high frequency geophones were rented fro the field period. A sledge hamme and a drop weight were tested as wave sources. The sounding was carried out on outcropped area in order to record high frequency reflections from known subhorizontal fracture zones as shallow as 30 m. Large amplitude surface waves hide most of the shallow reflections, recognizable only on few traces in the data. The data processing carried out did not reveal the geometry of these reflectors. Events arriving after the ground roll were analyzed in 2-folded CDP-sections. The continuous reflective horizons in them correspond to lithological changes and fracture zones located deeper than 200 m in the bedrock

Ultramafic-derived arsenic in a fractured bedrock aquifer

Science.gov (United States)

Ryan, P.C.; Kim, J.; Wall, A.J.; Moen, J.C.; Corenthal, L.G.; Chow, D.R.; Sullivan, C.M.; Bright, K.S.

2011-01-01

In the fractured bedrock aquifer of northern Vermont, USA, As concentrations in groundwater range from chemical extraction, X-ray diffraction (XRD) and stoichiometric analysis indicates that the majority of the As is located in antigorite and magnesite (MgCO3) with lesser amounts in magnetite (Fe3O4). Hydrochemistry of monitoring wells drilled into fractured ultramafic rock in a groundwater recharge area with no anthropogenic As source reveals above background As (2-9??g/L) and an Mg-HCO3 hydrochemical signature that reflects dissolution of antigorite and magnesite, confirming that As in groundwater can be derived from ultramafic rock dissolution. Arsenic mobility in groundwater affected by ultramafic rock dissolution may be enhanced by alkaline pH values and relatively high HCO3- concentrations. ?? 2011 Elsevier Ltd.

Steeply dipping heaving bedrock, Colorado: Part 2 - Mineralogical and engineering properties

Science.gov (United States)

Noe, D.C.; Higgins, J.D.; Olsen, H.W.

2007-01-01

This paper describes the mineralogical and engineering properties of steeply dipping, differentially heaving bedrock, which has caused severe damage near the Denver area. Several field sites in heave-prone areas have been characterized using high sample densities, numerous testing methodologies, and thousands of sample tests. Hydrometer testing shows that the strata range from siltstone to claystone (33 to 66 percent clay) with occasional bentonite seams (53 to 98 percent clay mixed with calcite). From X-ray diffraction analyses, the claystone contains varying proportions of illite-smectite and discrete (pure) smectite, and the bentonite contains discrete smectite. Accessory minerals include pyrite, gypsum, calcite, and oxidized iron compounds. The dominant exchangeable cation is Ca2+, except where gypsum is prevalent, and Mg2+ and Na1+ are elevated. Scanning electron microscope analyses show that the clay fabric is deformed and porous and that pyrite is absent within the weathered zone. Unified Soil Classification for the claystone varies from CL to CH, and the bentonite is CH to MH. Average moisture content values are 17 percent for claystone and 32 percent for bentonite, and these are typically 0 to 5 percent lower than the plastic limit. Swell-consolidation and suction testing shows a full range of swelling potentials from low to very high. These findings confirm that type I (bed-parallel, symmetrical to asymmetrical) heave features are strongly associated with changes in bedrock composition and mineralogy. Composition changes are not necessarily a factor for type II (bed-parallel to bed-oblique, strongly asymmetrical) heave features, which are associated with movements along subsurface shear zones.

The Decline of Soil Infiltration Capacity Due To High Elevation Groundwater

OpenAIRE

Isri Ronald Mangangka

2008-01-01

Infiltration capacity of soil mainly depends on two factors; the particle size and the moisture content of the soil. Groundwater increases the soil moisture, not only below the water table but also within the capillary zone, above the water table. Field experiment in a high groundwater area was conducted to understand the relationship among the groundwater, soil moisture and infiltration capacity. Using a single ring infiltrometer, the effect of groundwater in the infiltration rate was observ...

The Breakdown: Hillslope Sources of Channel Blocks in Bedrock Landscapes

Science.gov (United States)

Selander, B.; Anderson, S. P.; Rossi, M.

2017-12-01

Block delivery from hillslopes is a poorly understood process that influences bedrock channel incision rates and shapes steep terrain. Previous studies demonstrate that hillslope sediment delivery rate and grain size increases with channel downcutting rate or fracture density (Attal et al., 2015, ESurf). However, blocks that exceed the competence of the channel can inhibit incision. In Boulder Creek, a bedrock channel in the Colorado Front Range, large boulders (>1 m diameter) are most numerous in the steepest channel reaches; their distribution seems to reflect autogenic channel-hillslope feedback between incision rate and block delivery (Shobe et al., 2016, GRL). It is clear that the processes, rates of production, and delivery of large blocks from hillslopes into channels are critical to our understanding of steep terrain evolution. Fundamental questions are 1) whether block production or block delivery is rate limiting, 2) what mechanisms release blocks, and 3) how block production and transport affect slope morphology. As a first step, we map rock outcrops on the granodiorite hillslopes lining Boulder Creek within Boulder Canyon using a high resolution DEM. Our algorithm uses high ranges of curvature values in conjunction with slopes steeper than the angle of repose to quickly identify rock outcrops. We field verified mapped outcrop and sediment-mantled locations on hillslopes above and below the channel knickzone. We find a greater abundance of exposed rock outcrops on steeper hillslopes in Boulder Canyon. Additionally, we find that channel reaches with large in-channel blocks are located at the base of hillslopes with large areas of exposed bedrock, while reaches lacking large in-channel blocks tend to be at the base of predominately soil mantled and forested hillslopes. These observations support the model of block delivery and channel incision of Shobe et al. (2016, GRL). Moreover, these results highlight the conundrum of how rapid channel incision is

A Test of the Circumvention-of-Limits Hypothesis in Scientific Problem Solving: The Case of Geological Bedrock Mapping

Science.gov (United States)

Hambrick, David Z.; Libarkin, Julie C.; Petcovic, Heather L.; Baker, Kathleen M.; Elkins, Joe; Callahan, Caitlin N.; Turner, Sheldon P.; Rench, Tara A.; LaDue, Nicole D.

2012-01-01

Sources of individual differences in scientific problem solving were investigated. Participants representing a wide range of experience in geology completed tests of visuospatial ability and geological knowledge, and performed a geological bedrock mapping task, in which they attempted to infer the geological structure of an area in the Tobacco…

Water resources of Rockland County, New York, 2005-07, with emphasis on the Newark Basin Bedrock Aquifer

Science.gov (United States)

Heisig, Paul M.

2011-01-01

of 25 percent in 2005). In most cases, pump rates would have to be reduced as aquifer yield declines. This analysis underlines the fragility of the aquifer given the fact that recent years (2003-06) have been relatively wet. Impervious surfaces increase the amount of stormflow and decrease the amount of base flow in streams. Analysis of stormflows in watersheds with 11.9 and 17 percent impervious surface area increased the percentage of rainfall that becomes stormflow in streams by 7 to 8 percent and by 12.5 to 16.5 percent, respectively. Recharge was estimated from streamflow data and from groundwater-level data. Estimates from across the county in 1961 ranged from 24.8 inches in the northwest (New York Highlands area) to 14.7 inches in the southeast. Water budgets were generated for three basins with streamflow data. During 1959-94 and in 2006, groundwater pumpage for public supply accounted for 12 to 24 percent of recharge within the Mahwah River near Suffern, NY, watershed. Public-supply pumpage as a percentage of recharge in 2006 at the two other currently gaged watersheds (Pascack Brook and Saddle River) was 18 and 21 percent, respectively. About 12.9 billion gallons of water was used in Rockland County in 2005. The majority (63 percent) was for base-line domestic supply (non-growing season rates of use); of this amount, about 6 percent was from domestic wells and 94 percent was from production wells and reservoirs. Commercial, industrial, and institutional users made up 10 percent of total water use, and growing-season increases accounted for 18 percent. Sanitary sewers serve much of Rockland County and the majority of treated wastewater is discharged to the Hudson River, which is an estuary with brackish water adjacent to Rockland County. Inflow of stormwater and infiltration of groundwater constitute a significant additional contribution of water to the sanitary sewer system.

A field experiment on the controls of sediment transport on bedrock erosion

Science.gov (United States)

Beer, A. R.; Turowski, J. M.; Fritschi, B.; Rieke-Zapp, D.; Campana, L.; Lavé, J.

2012-12-01

The earth`s surface is naturally shaped by interactions of physical and chemical processes. In mountainous regions with steep topography river incision fundamentally controls the geomorphic evolution of the whole landscape. There, erosion of exposed bedrock sections by fluvial sediment transport is an important mechanism forming mountain river channels. The links between bedload transport and bedrock erosion has been firmly established using laboratory experiments. However, there are only few field datasets linking discharge, sediment transport, impact energy and erosion that can be used for process understanding and model evaluation. To fill this gap, a new measuring setup has been commissioned to raise an appropriate simultaneous dataset of hydraulics, sediment transport and bedrock erosion at high temporal and spatial resolution. Two natural stone slabs were installed flush with the streambed of the Erlenbach, a gauged stream in the Swiss Pre-Alps. They are mounted upon force sensors recording vertical pressure und downstream shear caused by passing sediment particles. The sediment transport rates can be assessed using geophone plates and an automated moving basket system taking short-term sediment samples. These devices are located directly downstream of the stone slabs. Bedrock erosion rates are measured continuously with erosion sensors at sub-millimeter accuracy at three points on each slab. In addition, the whole slab topography is surveyed with photogrammetry and a structured-light 3D scanner after individual flood events. Since the installation in 2011, slab bedrock erosion has been observed during several transport events. We discuss the relation between hydraulics, bedload transport, resulting pressure forces on the stone slabs and erosion rates. The aim of the study is the derivation of an empirical process law for fluvial bedrock erosion driven by moving sediment particles.

Durable terrestrial bedrock predicts submarine canyon formation

Science.gov (United States)

Smith, Elliot; Finnegan, Noah J.; Mueller, Erich R.; Best, Rebecca J.

2017-01-01

Though submarine canyons are first-order topographic features of Earth, the processes responsible for their occurrence remain poorly understood. Potentially analogous studies of terrestrial rivers show that the flux and caliber of transported bedload are significant controls on bedrock incision. Here we hypothesize that coarse sediment load could exert a similar role in the formation of submarine canyons. We conducted a comprehensive empirical analysis of canyon occurrence along the West Coast of the contiguous United States which indicates that submarine canyon occurrence is best predicted by the occurrence of durable crystalline bedrock in adjacent terrestrial catchments. Canyon occurrence is also predicted by the flux of bed sediment to shore from terrestrial streams. Surprisingly, no significant correlation was observed between canyon occurrence and the slope or width of the continental shelf. These findings suggest that canyon incision is promoted by greater yields of durable terrestrial clasts to the shore.

The application of alpha-card measurement to search underground water resources in bedrock

International Nuclear Information System (INIS)

Xiong Fulin; Liang Jinhua

1986-01-01

The alpha-card measurement is a new kind of nuclear technique to evaluate the concentration of the radium and thorium emanations with a short-time accumulation. It has shown the wonderful characteristics of higher sensitivity, greater detective depth, less interference and shorter work period when applied to search underground water resources in bedrock. The satisfactory result of its application in Pingyin limestone area is described. The principle of the alpha-card measurement and the foundation of its application are briefly discussed

A MODFLOW Infiltration Device Package for Simulating Storm Water Infiltration.

Science.gov (United States)

Jeppesen, Jan; Christensen, Steen

2015-01-01

This article describes a MODFLOW Infiltration Device (INFD) Package that can simulate infiltration devices and their two-way interaction with groundwater. The INFD Package relies on a water balance including inflow of storm water, leakage-like seepage through the device faces, overflow, and change in storage. The water balance for the device can be simulated in multiple INFD time steps within a single MODFLOW time step, and infiltration from the device can be routed through the unsaturated zone to the groundwater table. A benchmark test shows that the INFD Package's analytical solution for stage computes exact results for transient behavior. To achieve similar accuracy by the numerical solution of the MODFLOW Surface-Water Routing (SWR1) Process requires many small time steps. Furthermore, the INFD Package includes an improved representation of flow through the INFD sides that results in lower infiltration rates than simulated by SWR1. The INFD Package is also demonstrated in a transient simulation of a hypothetical catchment where two devices interact differently with groundwater. This simulation demonstrates that device and groundwater interaction depends on the thickness of the unsaturated zone because a shallow groundwater table (a likely result from storm water infiltration itself) may occupy retention volume, whereas a thick unsaturated zone may cause a phase shift and a change of amplitude in groundwater table response to a change of infiltration. We thus find that the INFD Package accommodates the simulation of infiltration devices and groundwater in an integrated manner on small as well as large spatial and temporal scales. © 2014, National Ground Water Association.

Quaternary sediment thickness and bedrock topography of the glaciated United States east of the Rocky Mountains

Science.gov (United States)

Soller, David R.; Garrity, Christopher P.

2018-01-26

Beginning roughly 2.6 million years ago, global climate entered a cooling phase known as the Pleistocene Epoch. As snow in northern latitudes compacted into ice several kilometers thick, it flowed as glaciers southward across the North American continent. These glaciers extended across the northern United States, dramatically altering the landscape they covered. East of the Rocky Mountains, the ice coalesced into continental glaciers (called the Laurentide Ice Sheet) that at times blanketed much of the north-central and northeastern United States. To the west of the Laurentide Ice Sheet, glaciers formed in the mountains of western Canada and the United States and coalesced into the Cordilleran ice sheet; this relatively smaller ice mass extended into the conterminous United States in the northernmost areas of western Montana, Idaho, and Washington. Throughout the Pleistocene, landscape alteration occurred by (1) glacial erosion of the rocks and sediments; (2) redeposition of the eroded earth materials in a form substantially different from their source rocks, in terms of texture and overall character; and (3) disruption of preexisting drainage patterns by the newly deposited sediments. In many cases, pre-glacial drainage systems (including, for example, the Mississippi River) were rerouted because their older drainage courses became blocked with glacial sediment.The continental glaciers advanced and retreated many times across those areas. During each ice advance, or glaciation, erosion and deposition occurred, and the landscape was again altered. Through successive glaciations, the landscape and the bedrock surface gradually came to resemble their present configurations. As continental ice sheets receded and the Pleistocene ended, erosion and deposition of sediment (for example in stream valleys) continued to shape the landscape up to the present day (albeit to a lesser extent than during glaciation). The interval of time since the last recession of the glaciers

Evaluation of bedrock mainly composed of volcanic aggregate rocks at the Higashidori Nuclear Power Station

International Nuclear Information System (INIS)

Hashimoto, Shuichi; Miwa, Tadashi; Nishidachi, Masayuki

2000-01-01

When carrying out engineering evaluation on foundation bedrock for important constructions such as nuclear power station, dam, and so forth, it is required as a premise on carrying out various surveys, tests, and analyses to select adequate geological elements, to classify them to some groups capable of regarding as a common engineering property, and to rate them. On a hard bedrock, there is a classification method with relatively higher versatility adding condition of crack and weathering to performances at each site as an index, but on a soft one, most of its classification are carried out individually for its site in response to an index caused by the bedrock itself. Here were shown the results carried out some bedrock classifications on a base of grouping for rock sorts and rock phases, according to some concepts on a draft of the standard on the soft bedrock classification due to the nuclear engineering committee of the Japan Society of Civil Engineers, a reference draft on the soft bedrock classification of the 'Technical indications on seismic resistance design of the nuclear power station' of the Japan Electric Association, (JEAG4601-1987), and so forth. As a result applied the reference draft on the soft bedrock, and so forth to the bedrock at the Higashidori Nuclear Power Station composed of volcanic aggregate rocks of the Miocene epoch of the new Tertiary system, an adequate engineering evaluation was made possible by making grouping of rock sorts and rock phases to a foundation. And, on property evaluation of the quality changed vein, as a result of various tests, appropriate properties could be obtained. (G.K.)

Root distribution and seasonal water status in weathered granitic bedrock under chaparral

Science.gov (United States)

P. D. Sternberg; M. A. Anderson; R. C. Graham; J. L. Beyers; K. R. Tice

1996-01-01

Soils in mountainous terrain are often thin and unable to store sufficient water to support existing vegetation through dry seasons. This observation has led to speculation about the role of bedrock in supporting plant growth in natural ecosystems, since weathered bedrocks often have appreciable porosity and, like soil, can store and transmit water. This study, within...

Inactivation of VHSV by infiltration and salt under experimental conditions

DEFF Research Database (Denmark)

Skall, Helle Frank; Jørgensen, Claus; Olesen, Niels Jørgen

2014-01-01

At the moment the only legal method in Denmark to sanitize wastewater from fish cutting plants is by infiltration. To evaluate the inactivation effect of infiltration on VHSV an experimental examination was initiated. A column packed with gravel as top- and bottom layer (total of 22 cm) and a mid...... be a valuable method to sanitize VHSV infected water. Changes in temperature, pH, earth types in the area used for infiltration etc. may change the virus reduction, though. As some of the fish cutting plants are also smoking rainbow trout fillets, the question arose whether a brine solution will inactivate VHSV...

A rapid screening-level method to optimize location of infiltration ponds.

Science.gov (United States)

Fennemore, G G; Davis, A; Goss, L; Warrick, A W

2001-01-01

A rapid-screening technique was developed to identify lithologies that best disperse artificial recharge via surface infiltration and minimize effects on ground water chemistry. The technique prospectively evaluates basin infiltration rates and water chemistry influences by integrating geotechnical, hydraulic, and water quality data with column test data and numerical modeling. The technique was validated using field data collected from surface infiltration basins designed to recharge ground water pumped from the Pipeline pit gold mine in Nevada. Observed recharge rates at these infiltration sites correlated most significantly with depth to groundwater, with basins in coarse-grained lithologies performing better (0.45 to 0.85 m/day) than those with fine-grained layers ( 2000 mg/L) than coarse-grained soils (infiltration basins for a variety of lithologies. Sites for infiltration basins can be rapidly screened to include areas with greatest depth to groundwater and in coarsest alluvial sediments, and impact to ground water chemistry can be reliably predicted using computer modeling and column test results.

Geohydrologic and water-quality characterization of a fractured-bedrock test hole in an area of Marcellus shale gas development, Tioga County, Pennsylvania

Science.gov (United States)

Williams, John H.; Risser, Dennis W.; Hand , K.L; Clifford H. Dodge,

2013-01-01

An integrated analysis of core, geophysical logs, gas isotopes, and specific-depth water-quality samples from the Cherry Flats test hole was used to characterize the stratigraphy, water-bearing zones, and groundwater quality at a site in southern Tioga County, Pennsylvania. The study was completed as a cooperative effort between the Pennsylvania Department of Natural Resources, Bureau of Topographic and Geologic Survey (BTGS) and the U.S. Geological Survey (USGS). The multi-disciplinary characterization of the test hole provided information to aid the bedrock mapping of the Cherry Flats 7.5-minute quadrangle by BTGS, and to help quantify the depth and character of fresh and saline groundwater in an area of shale-gas exploration. The Cherry Flats test hole was cored to a depth of 1,513 feet (ft) below land surface (bls) and cased to 189 ft through the collapsed mine workings of the former Arnot No. 2 underground coal mine. The test hole penetrated

Bedrock Geologic Map of the Underhill quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG03-4B Doolan, B., Cherchetti, L., Holt, J., Ryan, J., Hengstenburg, C., and Rosencrantz, E., 2003,�Bedrock Geologic Map of the Underhill...

Bedrock Geologic Map of the Bristol, VT Quadrangle

Data.gov (United States)

Vermont Center for Geographic Information — Digital data from VG13-1 Kim, J, Weber, E, and Klepeis, K, 2013, Bedrock Geologic Map of the Bristol, VT Quadrangle: Vermont Geological Survey Open File Report...

Indoor air quality/air infiltration in selected low-energy houses

International Nuclear Information System (INIS)

Shohl Wagner, B.; Phillips, T.J.

1984-01-01

Indoor air quality and air infiltration were measured in 16 low-energy California houses. Eleven has gas stoves; all had average infiltration rates of 0.5 h -1 of less, recent construction dates, low natural ventilation, and no mechanical ventilation. HCHO levels in 12 houses and radon-222 and NO 2 levels in all houses were measured using passive monitors. Blower door measurements and local weather data were used to calculate average infiltration rates during the monitoring period. Correlation of pollutant concentrations with infiltration rates and building characteristics indicate that new houses with average heating season infiltration rates less than 0.5 h -1 do not necessarily experience poor indoor air quality, HCHO and radon-222 levels in new houses exceeded the lowest currently proposed standards or guidelines, and much higher levels probably exist elsewhere. Therefore, some strategy for identifying 'problem' houses is needed. We recommend an approach for future research in this area. (Author)

Rural Community Development: Bedrock for National Development ...

African Journals Online (AJOL)

This paper advocates that community development is the bedrock for national development. For any meaningful development to take place, whether national or global development must have its building blocks or firm-root in rural development. However, the rural communities are characterized by isolation from ideas and ...

Infiltrated carbon foam composites

Science.gov (United States)

Lucas, Rick D. (Inventor); Danford, Harry E. (Inventor); Plucinski, Janusz W. (Inventor); Merriman, Douglas J. (Inventor); Blacker, Jesse M. (Inventor)

2012-01-01

An infiltrated carbon foam composite and method for making the composite is described. The infiltrated carbon foam composite may include a carbonized carbon aerogel in cells of a carbon foam body and a resin is infiltrated into the carbon foam body filling the cells of the carbon foam body and spaces around the carbonized carbon aerogel. The infiltrated carbon foam composites may be useful for mid-density ablative thermal protection systems.

The effect of wet-dry weathering on the rate of bedrock river channel erosion by saltating gravel

Science.gov (United States)

Inoue, Takuya; Yamaguchi, Satomi; Nelson, Jonathan M.

2017-01-01

Previous work has shown that the bedrock erosion rate E because of collisions of saltating bedload can be expressed by E = βqb(1-Pc), where qb is the sediment transport rate, Pc is the extent of alluvial cover, and β is the abrasion coefficient. However, the dependence of the abrasion coefficient on the physical characteristics of the bedrock material is poorly known, and in particular, the effects of wet-dry weathering on the saltation-abrasion bedrock incision has not been specifically characterized. Observation suggests that the typical wet-dry cycling of exposed bedrock in river beds gives rise to cracks and voids that are likely to alter the incision rate of the material when subjected to impacts of moving sediment. In this study, flume experiments are performed to develop an understanding of how wet-dry cycling affects the rock tensile strength and the bedrock erosion rate. To represent the physical effects of weathering, boring cores taken from natural bedrock channel are exposed to artificial wet-dry cycles. The experimental results suggest the following: (1) the abrasion coefficient for fresh bedrock is estimated by β = 1.0 × 10− 4σT− 2(d/ksb)0.5, where σT is the tensile strength, d is the diameter of colliding gravel, and ksb is the hydraulic roughness height of bedrock; (2) the tensile strength of the bedrock decreases exponentially as a result of repeated wet-dry cycles, σT/σT0 = exp (-CTNWa0/σT0), where σT0 is the initial tensile strength, Wa0 is the initial normalized rate of water absorption., N is the number of wet-dry cycles, and CT is a constant; (3) the erosion rate of fresh bedrock depends on the inverse of the square of tensile strength, but the erosion rate of weathered bedrock depends on the − 1.5 power of tensile strength.

Large bedrock slope failures in a British Columbia, Canada fjord: first documented submarine sackungen

Science.gov (United States)

Conway, Kim W.; Vaughn Barrie, J.

2018-01-01

Very large (>60×106 m3) sackungen or deep-seated gravitational slope deformations occur below sea level along a steep fjord wall in central Douglas Channel, British Columbia. The massive bedrock blocks were mobile between 13 and 11.5 thousand radiocarbon years BP (15,800 and 13,400 BP) immediately following deglaciation. Deformation of fjord sediments is apparent in sedimentary units overlying and adjacent to the blocks. Faults bound the edges of each block, cutting the glacial section but not the Holocene sediments. Retrogressive slides, small inset landslides as well as incipient and older slides are found on and around the large failure blocks. Lineations, fractures and faults parallel the coastline of Douglas Channel along the shoreline of the study area. Topographic data onshore indicate that faults and joints demarcate discrete rhomboid-shaped blocks which controlled the form, size and location of the sackungen. The described submarine sackungen share characteristic geomorphic features with many montane occurrences, such as uphill-facing scarps, foliated bedrock composition, largely vertical dislocation and a deglacial timing of development.

Preliminary hydrogeologic assessment of a ground-water contamination area in Wolcott, Connecticut

Science.gov (United States)

Stone, J.R.; Casey, G.D.; Mondazzi, R.A.; Frick, T.W.

1997-01-01

Contamination of ground water by volatile organic compounds and inorganic constituents has been identified at a number of industrial sites in the Town of Wolcott, Connecticut. Contamination is also present at a municipal landfill in the City of Waterbury that is upgradient from the industrial sites in the local ground-water-flow system. The study area, which lies in the Western Highlands of Connecticut, is in the Mad River Valley, a tributary to the Naugatuck River. Geohydrologic units (aquifer materials) include unconsolidated glacial sediments (surficial materials) and fractured crystalline (metamorphic) bedrock. Surficial materials include glacial till, coarse-grained andfine-grained glacial stratified deposits, and postglacial floodplain alluvium and swamp deposits. The ground-water-flow system in the surficial aquifer is complex because the hydraulic properties of the surficial materials are highly variable. In the bedrock aquifer, ground water moves exclusively through fractures. Hydrologic characteristics of the crystalline bedrock-degree of confinement, hydraulic conductivity, storativity, and porosity-are poorly defined in the study area. Further study is needed to adequately assess ground-water flow and contaminant migration under current or past hydrologic conditions. All known water-supply wells in the study area obtain water from the bedrock aquifer. Twenty households in a hillside residential area on Tosun Road currently obtain drinking water from private wells tapping the bedrock aquifer. The extent of contamination in the bedrock aquifer and the potential for future contamination from known sources of contamination in the surficial aquifer is of concern to regulatory agencies. Previous investigations have identified ground-water contamination by volatile organic compounds at the Nutmeg Valley Road site area. Contamination has been associated with on-site disposal of heavy metals, chlorinated and non-chlorinated volatile organic compounds, and

The geology of the Romuvaara area

International Nuclear Information System (INIS)

Anttila, P.; Paulamaeki, S.; Lindberg, A.; Paananen, M.; Pitkaenen, P.; Front, K.

1990-12-01

Teollisuuden Voima Oy (TVO) is preparing for the final disposal of spent uranium fuel from the Olkiluoto nuclear power plant deep in the Finnish bedrock. The report presents a summary of the geological conditions at Romuvaara in Kuhmo, which was one of the five areas selected in 1987 for the preliminary site investigations. The Romuvaara site and its surroundings belong to the Archaean basement complex, the age of the oldest parts of which is over 2800 Ma. The bedrock consists mainly of migmatic banded gneisses (tonalite, leucotonalite and mica gneiss). These rock types are intersected by granodiorite and metadiabase dykes. Proterozoic metadiabases represent the youngest rock unit in the area. Except for the metadiabase, the rocks have undergone a multiphase Archaean deformation. The bedrock structures are interpreted as representing six deformation phases, after which sharp faults developed during at least four further movement phases

The soil apparent infiltrability observed with ponded infiltration experiment in a permanent grid of infiltration rings

Czech Academy of Sciences Publication Activity Database

Votrubová, J.; Jelínková, V.; Němcová, R.; Tesař, Miroslav; Vogel, T.; Císlerová, M.

2010-01-01

Roč. 12, - (2010), s. 11898 ISSN 1607-7962. [European Geosciences Union General Assembly 2010. 02.05.2010-07.05.2010, Wienna] R&D Projects: GA ČR GA205/08/1174 Institutional research plan: CEZ:AV0Z20600510 Keywords : soil hydraulic conductivity * infiltration * infiltration ring Subject RIV: DA - Hydrology ; Limnology

Effects of climate change on residential infiltration and air pollution exposure.

Science.gov (United States)

Ilacqua, Vito; Dawson, John; Breen, Michael; Singer, Sarany; Berg, Ashley

2017-01-01

Air exchange through infiltration is driven partly by indoor/outdoor temperature differences, and as climate change increases ambient temperatures, such differences could vary considerably even with small ambient temperature increments, altering patterns of exposures to both indoor and outdoor pollutants. We calculated changes in air fluxes through infiltration for prototypical detached homes in nine metropolitan areas in the United States (Atlanta, Boston, Chicago, Houston, Los Angeles, Minneapolis, New York, Phoenix, and Seattle) from 1970-2000 to 2040-2070. The Lawrence Berkeley National Laboratory model of infiltration was used in combination with climate data from eight regionally downscaled climate models from the North American Regional Climate Change Assessment Program. Averaged over all study locations, seasons, and climate models, air exchange through infiltration would decrease by ~5%. Localized increased infiltration is expected during the summer months, up to 20-30%. Seasonal and daily variability in infiltration are also expected to increase, particularly during the summer months. Diminished infiltration in future climate scenarios may be expected to increase exposure to indoor sources of air pollution, unless these ventilation reductions are otherwise compensated. Exposure to ambient air pollution, conversely, could be mitigated by lower infiltration, although peak exposure increases during summer months should be considered, as well as other mechanisms.

Physically based probability criterion for exceeding radionuclide concentration limits in heterogeneous bedrock

International Nuclear Information System (INIS)

Worman, A.; Xu, S.; Dverstorp, B.

2004-01-01

A significant problem in a risk analysis of the repository for high-level nuclear waste is to estimate the barrier effect of the geosphere. The significant spatial variability of the rock properties implies that migrating RNs encounter a distribution of bedrock properties and mass-transfer mechanisms in different proportions along the transport paths. For practical reasons, we will never be able to know exactly this distribution of properties by performing a reasonable amount of measurements in a site investigation. On the contrary, recent experimental studies reveal that crystalline bedrock can possess a marked heterogeneity of various physical and geochemical properties that potentially may have a certain impact on the transport of RNs in fractured bedrock. Also current field investigation techniques provide only fragmentary information of the properties of the geosphere. This is a basic motivation for treating flows of water and solute elements in groundwaters by means of stochastic continuum models. The stochastic analysis is based on the idea that we know only certain point values of the property fields and use this information to estimate intermediate values. The probabilistic properties of the stochastic analysis are suitable input variables for risk analyses of the relevant sequence of extreme events for which empirical observations are rare or non-existing. The purpose of this paper is to outline the implications of the stochastic approach for estimating probabilities that certain concentration limits are exceeded at discharge points from. the bedrock in case of a leakage from the waste repository. The analysis is restricted to the water flow and solute transport in the bedrock alone without consideration of the full sequence of events in a full risk analysis and the Bayesian statistics involved in such conditioned (and cross-correlated) event series. The focus is on the implication for the risk analysis of the auto-covariance structure in bedrock

An investigation into the bedrock depth in the Eskisehir Quaternary Basin (Turkey) using the microtremor method

Science.gov (United States)

Tün, M.; Pekkan, E.; Özel, O.; Guney, Y.

2016-10-01

Eskişehir Basin and the results of deep drilling, shallow drilling, shear wave velocity measurement and sedimentary cover depth measurement obtained from the seismic reflection section was expressed in the form of a nonlinear regression equation. An empirical relationship between fr, the thickness of sediments and the bedrock depth is suggested for use in future microzonation studies of sites in the region. The results revealed a maximum basin depth of 1000 m, located in the northeast of the Eskişehir Basin, and the SPAC and HVSR results indicated that within the study area the basin is characterized by a thin local sedimentary cover with low shear wave velocity overlying stiff materials, resulting in a sharp velocity contrast. The thicknesses of the old Quaternary and Tertiary fluvial sediments within the basin serve as the primary data sources in seismic hazard and seismic site response studies, and these results add to the body of available seismic hazard data contributing to a seismic microzonation of the Eskişehir Graben in advance of the severe earthquakes expected in the Anatolian Region.

Hydrologic behaviour of stormwater infiltration trenches in a central urban area during 2 3/4 years of operation

DEFF Research Database (Denmark)

Warnaars, E.; Larsen, A.V.; Jacobsen, P.

1999-01-01

overflow. Analyses of falling water tables after rain indicated slight clogging, but this effect is less important than the general lack of knowledge about soil permeability for normal design situations. The results indicate that the stormwater infiltration in central urban areas with compressed soils...... an initial soil survey. Although the two trenches are placed close to each other they function rather differently, corresponding to effective soil permeabilities of 2.10(-6) m/s in one trench and a factor 10 smaller in the other. During 23/4 years of measuring 89 events were recorded, of which 7 caused...

An ice flow modeling perspective on bedrock adjustment patterns of the Greenland ice sheet

Directory of Open Access Journals (Sweden)

M. Olaizola

2012-11-01

Full Text Available Since the launch in 2002 of the Gravity Recovery and Climate Experiment (GRACE satellites, several estimates of the mass balance of the Greenland ice sheet (GrIS have been produced. To obtain ice mass changes, the GRACE data need to be corrected for the effect of deformation changes of the Earth's crust. Recently, a new method has been proposed where ice mass changes and bedrock changes are simultaneously solved. Results show bedrock subsidence over almost the entirety of Greenland in combination with ice mass loss which is only half of the currently standing estimates. This subsidence can be an elastic response, but it may however also be a delayed response to past changes. In this study we test whether these subsidence patterns are consistent with ice dynamical modeling results. We use a 3-D ice sheet–bedrock model with a surface mass balance forcing based on a mass balance gradient approach to study the pattern and magnitude of bedrock changes in Greenland. Different mass balance forcings are used. Simulations since the Last Glacial Maximum yield a bedrock delay with respect to the mass balance forcing of nearly 3000 yr and an average uplift at present of 0.3 mm yr⁻¹. The spatial pattern of bedrock changes shows a small central subsidence as well as more intense uplift in the south. These results are not compatible with the gravity based reconstructions showing a subsidence with a maximum in central Greenland, thereby questioning whether the claim of halving of the ice mass change is justified.

Hydrochemical Characteristics of Groundwater in an Agricultural Area in South Korea

Science.gov (United States)

Kim, N.; Hamm, S.; An, J.; Lee, J.; Jang, S.

2008-12-01

The study area, Sacheon-Hadong area, is located in the southern part of the Korean peninsula, which is bounded by the South Sea and surrounded by the Seomjin River in the west. The study area utilized for agricultural work for a long time. That resulted in vulnerable situation of groundwater due to contamination by fertilizer, insecticide and other human activities. In addition, groundwater is in the risk of seawater intrusion because of the study area's location nearby the South Sea. In Sacheon and Hadong area, the EC values were higher in alluvial aquifer than bedrock aquifer. The higher EC values in the alluvial groundwater than the bedrock groundwater were influenced by agricultural activity in near-surface. Water types of two groundwaters belong to Ca-Cl and Na-Cl types due to saline-water influence. EC values are raised, becoming close to the coast. The correlation analysis showed that EC had positive relationship with Na+, Ca2+, Mg2+, Fe2+, Mn2+, SO42-, and Cl-, indicating mixing with seawater. In Sacheon area, nitrogen isotope ratios in the alluvial groundwater ranged between -0.40 and 12.80‰, with 0.05~2.49 mg/l of NO3-N concentration; the range of nitrogen isotopes in the bedrock groundwater was between 3.30 and 17.60‰, with 0.12~2.14 mg/l of NO3-N concentration. Nitrogen was originated from organic source in soils, manures, and domestic wastes (Mueller and Helsel, 1996; Kim and Woo, 2003). In Hadong area, the nitrogen isotopes in the alluvial groundwater ranged from -0.50 to 19.10‰, and NO3-N concentration was between 0.63 and 6.68 mg/l. And these may be originated from anthropogenic pollutants (Mueller and Helsel, 1996). In Sacheon area, average δ18O and δD in alluvial groundwater were analyzed as - 6.77‰ and -47.50‰; average isotope ratios in bedrock groundwater were -7.73‰ and - 53.46‰. In Hadong area, average δ18O and δD in the alluvial groundwater were - 7.32‰ and -49.80‰; average isotope ratios in the bedrock groundwater

Bedrock Geologic Map of Vermont - Faults and Contacts

Data.gov (United States)

Vermont Center for Geographic Information — The bedrock geology was last mapped at a statewide scale 50 years ago at a scale of 1:250,000 (Doll and others, 1961). The 1961 map was compiled from 1:62,500-scale...

Bedrock Geologic Map of Vermont - Geochronology Sample Locations

Data.gov (United States)

Vermont Center for Geographic Information — The bedrock geology was last mapped at a statewide scale 50 years ago at a scale of 1:250,000 (Doll and others, 1961). The 1961 map was compiled from 1:62,500-scale...

Spatial variability of steady-state infiltration into a two-layer soil system on burned hillslopes

Science.gov (United States)

Kinner, D.A.; Moody, J.A.

2010-01-01

Rainfall-runoff simulations were conducted to estimate the characteristics of the steady-state infiltration rate into 1-m2 north- and south-facing hillslope plots burned by a wildfire in October 2003. Soil profiles in the plots consisted of a two-layer system composed of an ash on top of sandy mineral soil. Multiple rainfall rates (18.4-51.2 mm h-1) were used during 14 short-duration (30 min) and 2 long-duration simulations (2-4 h). Steady state was reached in 7-26 min. Observed spatially-averaged steady-state infiltration rates ranged from 18.2 to 23.8 mm h-1 for north-facing and from 17.9 to 36.0 mm h-1 for south-facing plots. Three different theoretical spatial distribution models of steady-state infiltration rate were fit to the measurements of rainfall rate and steady-state discharge to provided estimates of the spatial average (19.2-22.2 mm h-1) and the coefficient of variation (0.11-0.40) of infiltration rates, overland flow contributing area (74-90% of the plot area), and infiltration threshold (19.0-26 mm h-1). Tensiometer measurements indicated a downward moving pressure wave and suggest that infiltration-excess overland flow is the runoff process on these burned hillslope with a two-layer system. Moreover, the results indicate that the ash layer is wettable, may restrict water flow into the underlying layer, and increase the infiltration threshold; whereas, the underlying mineral soil, though coarser, limits the infiltration rate. These results of the spatial variability of steady-state infiltration can be used to develop physically-based rainfall-runoff models for burned areas with a two-layer soil system. ?? 2010 Elsevier B.V.

Variably-saturated groundwater modeling for optimizing managed aquifer recharge using trench infiltration

Science.gov (United States)

Heilweil, Victor M.; Benoit, Jerome; Healy, Richard W.

2015-01-01

Spreading-basin methods have resulted in more than 130 million cubic meters of recharge to the unconfined Navajo Sandstone of southern Utah in the past decade, but infiltration rates have slowed in recent years because of reduced hydraulic gradients and clogging. Trench infiltration is a promising alternative technique for increasing recharge and minimizing evaporation. This paper uses a variably saturated flow model to further investigate the relative importance of the following variables on rates of trench infiltration to unconfined aquifers: saturated hydraulic conductivity, trench spacing and dimensions, initial water-table depth, alternate wet/dry periods, and number of parallel trenches. Modeling results showed (1) increased infiltration with higher hydraulic conductivity, deeper initial water tables, and larger spacing between parallel trenches, (2) deeper or wider trenches do not substantially increase infiltration, (3) alternating wet/dry periods result in less overall infiltration than keeping the trenches continuously full, and (4) larger numbers of parallel trenches within a fixed area increases infiltration but with a diminishing effect as trench spacing becomes tighter. An empirical equation for estimating expected trench infiltration rates as a function of hydraulic conductivity and initial water-table depth was derived and can be used for evaluating feasibility of trench infiltration in other hydrogeologic settings

[Is therapy with local infiltrations feasible in primary care consultations?].

Science.gov (United States)

Magaña Loarte, J E; Pérez Franco, J; Sánchez Sánchez, G

1999-01-01

To study the feasibility of local infiltration in primary care consultations. Before-and-after intervention study. Two clinics at an urban health centre. Patients diagnosed with pathology of tender areas and treated with corticosteroid infiltration between May 1997 and May 1998. Corticoid infiltration plus local anaesthetic. Weekly check-up. Analysis of the variables: sex, age, diagnosis, time elapsed between indication and start of treatment, subjective assessment of pain before and after treatment (VRS scale), number of infiltrations per patient, side-effects. Evaluation of overall and individual effectiveness. 41 patients were infiltrated. Average age was 58. Most common pathologies were: rotary joint tendinitis (48.7%), anserine bursitis (24.4%), plantar fasciitis (7.3%). Average number of infiltrations per pathology: 1.3. Mean waiting time: 3.5 days. Comparison of pain by means of VRS (range 0-5) before and after treatment used the Wilcoxon test, with a statistically significant difference and p < 0.001 (z = -5.5109). For 35 patients (85.4%), pain was solved very well (values 0 and 1 on the VRS). For 3 patients (7.3%), improvement was moderate; and for 3 (7.3%) there was no improvement. 1. Treatment with local infiltration of corticosteroids is effective in dealing with pain, and is an alternative to treatment with NSAIDs. 2. It is feasible in primary care, and there are many advantages if the general practitioner employs this therapeutic technique.

Apparent diffusion coefficient mapping in medulloblastoma predicts non-infiltrative surgical planes.

Science.gov (United States)

Marupudi, Neena I; Altinok, Deniz; Goncalves, Luis; Ham, Steven D; Sood, Sandeep

2016-11-01

An appropriate surgical approach for posterior fossa lesions is to start tumor removal from areas with a defined plane to where tumor is infiltrating the brainstem or peduncles. This surgical approach minimizes risk of damage to eloquent areas. Although magnetic resonance imaging (MRI) is the current standard preoperative imaging obtained for diagnosis and surgical planning of pediatric posterior fossa tumors, it offers limited information on the infiltrative planes between tumor and normal structures in patients with medulloblastomas. Because medulloblastomas demonstrate diffusion restriction on apparent diffusion coefficient map (ADC map) sequences, we investigated the role of ADC map in predicting infiltrative and non-infiltrative planes along the brain stem and/or cerebellar peduncles by medulloblastomas prior to surgery. Thirty-four pediatric patients with pathologically confirmed medulloblastomas underwent surgical resection at our facility from 2004 to 2012. An experienced pediatric neuroradiologist reviewed the brain MRIs/ADC map, assessing the planes between the tumor and cerebellar peduncles/brain stem. An independent evaluator documented surgical findings from operative reports for comparison to the radiographic findings. The radiographic findings were statistically compared to the documented intraoperative findings to determine predictive value of the test in identifying tumor infiltration of the brain stem cerebellar peduncles. Twenty-six patients had preoperative ADC mapping completed and thereby, met inclusion criteria. Mean age at time of surgery was 8.3 ± 4.6 years. Positive predictive value of ADC maps to predict tumor invasion of the brain stem and cerebellar peduncles ranged from 69 to 88 %; negative predictive values ranged from 70 to 89 %. Sensitivity approached 93 % while specificity approached 78 %. ADC maps are valuable in predicting the infiltrative and non-infiltrative planes along the tumor and brain stem interface in

Simulation of Groundwater Mounding Beneath Hypothetical Stormwater Infiltration Basins

Science.gov (United States)

Carleton, Glen B.

2010-01-01

Groundwater mounding occurs beneath stormwater management structures designed to infiltrate stormwater runoff. Concentrating recharge in a small area can cause groundwater mounding that affects the basements of nearby homes and other structures. Methods for quantitatively predicting the height and extent of groundwater mounding beneath and near stormwater Finite-difference groundwater-flow simulations of infiltration from hypothetical stormwater infiltration structures (which are typically constructed as basins or dry wells) were done for 10-acre and 1-acre developments. Aquifer and stormwater-runoff characteristics in the model were changed to determine which factors are most likely to have the greatest effect on simulating the maximum height and maximum extent of groundwater mounding. Aquifer characteristics that were changed include soil permeability, aquifer thickness, and specific yield. Stormwater-runoff variables that were changed include magnitude of design storm, percentage of impervious area, infiltration-structure depth (maximum depth of standing water), and infiltration-basin shape. Values used for all variables are representative of typical physical conditions and stormwater management designs in New Jersey but do not include all possible values. Results are considered to be a representative, but not all-inclusive, subset of likely results. Maximum heights of simulated groundwater mounds beneath stormwater infiltration structures are the most sensitive to (show the greatest change with changes to) soil permeability. The maximum height of the groundwater mound is higher when values of soil permeability, aquifer thickness, or specific yield are decreased or when basin depth is increased or the basin shape is square (and values of other variables are held constant). Changing soil permeability, aquifer thickness, specific yield, infiltration-structure depth, or infiltration-structure shape does not change the volume of water infiltrated, it changes the

Cyclic sciatica caused by infiltrative endometriosis: MRI findings

Energy Technology Data Exchange (ETDEWEB)

Yekeler, Ensar; Kumbasar, Basak; Tunaci, Atadan; Barman, Ahmet; Tunaci, Mehtap [Department of Radiology, Istanbul Faculty of Medicine, Istanbul University, 34390, Capa, Istanbul (Turkey); Bengisu, Ergin [Department of Obstetrics and Gynecology, Istanbul Faculty of Medicine, Istanbul University, Istanbul (Turkey); Yavuz, Ekrem [Department of Pathology, Istanbul Faculty of Medicine, Istanbul University, 34390, Capa, Istanbul (Turkey)

2004-03-01

Endometriosis, an important gynecological disorder of reproductive women, affects most commonly the ovaries and less frequently the gastrointestinal tract, chest, urinary tract, and soft tissues. Endometriosis classically appears on MRI as a mass with a large cystic component and variable signal intensities on T1- and T2-weighted images due to the presence of variable degradation of hemorrhagic products. Endometriosis in an atypical location, an infiltrative appearance and without cystic-hemorrhagic components has rarely been described. We report on a 33-year-old woman with cyclic sciatica due to histologically documented infiltrative endometriosis involving the area of the left sciatic notch. (orig.)

Cyclic sciatica caused by infiltrative endometriosis: MRI findings

International Nuclear Information System (INIS)

Yekeler, Ensar; Kumbasar, Basak; Tunaci, Atadan; Barman, Ahmet; Tunaci, Mehtap; Bengisu, Ergin; Yavuz, Ekrem

2004-01-01

Endometriosis, an important gynecological disorder of reproductive women, affects most commonly the ovaries and less frequently the gastrointestinal tract, chest, urinary tract, and soft tissues. Endometriosis classically appears on MRI as a mass with a large cystic component and variable signal intensities on T1- and T2-weighted images due to the presence of variable degradation of hemorrhagic products. Endometriosis in an atypical location, an infiltrative appearance and without cystic-hemorrhagic components has rarely been described. We report on a 33-year-old woman with cyclic sciatica due to histologically documented infiltrative endometriosis involving the area of the left sciatic notch. (orig.)

Low-temperature infiltration identified using infrared thermography in patients with subcutaneous edema revealed ultrasonographically: A case report.

Science.gov (United States)

Oya, Maiko; Takahashi, Toshiaki; Tanabe, Hidenori; Oe, Makoto; Murayama, Ryoko; Yabunaka, Koichi; Matsui, Yuko; Sanada, Hiromi

Infiltration is a frequent complication of infusion therapy. We previously demonstrated the usefulness of infrared thermography as an objective method of detecting infiltration in healthy people. However, whether thermography can detect infiltration in clinical settings remains unknown. Therefore, we report two cases where thermography was useful in detecting infiltration at puncture sites. In both cases, tissue changes were verified ultrasonographically. The patients were a 56-year-old male with cholangitis and a 76-year-old female with hepatoma. In both cases, infiltration symptoms such as swelling and erythema occurred one day after the insertion of a peripheral intravenous catheter. Thermographic images from both patients revealed low-temperature areas spreading from the puncture sites; however, these changes were not observed in other patients. The temperature difference between the low-temperature areas and their surrounding skin surface exceeded 1.0°C. Concurrently, ultrasound images revealed that tissues surrounding the vein had a cobblestone appearance, indicating edema. In both patients, subcutaneous tissue changes suggested infiltration and both had low-temperature areas spreading from the puncture sites. Thus, subcutaneous edema may indicate infusion leakage, resulting in a decrease in the temperature of the associated skin surface. These cases suggest that infrared thermography is an effective method of objectively and noninvasively detecting infiltration.

Nodular focal fatty infiltration of the liver: CT appearance

International Nuclear Information System (INIS)

Baker, M.E.; Silverman, P.M.

1985-01-01

Focal fatty infiltration of the liver is a well recognized entity generally characterized by a nonspherical, low-density area without significant mass effect. CT usually distinguishes this from focal liver processes such as abscess or metastasis by its sharply marginated, geographic pattern and lack of mass effect on hepatic and portal veins. Recently, the authors formed a CT scan of the liver in one patient in whom fatty infiltration appeared nodular or rounded. The clinical presentation and radiographic and pathologic features form the basis of this report

Regeneration of the liver at different periods of mononuclear infiltration induced by zymosan granules

International Nuclear Information System (INIS)

Shcherbakov, V.I.; Komlyagina, T.G.; Mayanskii, D.N.

1985-01-01

The aim of this investigation was to discover how the liver,with areas of mononuclear infiltration, developing in response to activation of Kupffer cells (KC) by zymosan granules (ZG), regenerates. In the experiments, an intraperitoneal injection of 1 microCi of 3 H-thymidine/g body weight was given to the mice 1 h before sacrifice. Proliferation of hepatocytes and regeneration of the liver were intensified most when partial resection of the liver (PRL) was performed at the peak of mononuclear infiltration of the liver, namely five days after injection of ZG. The data indicate that not only activated KC, but also areas of mononuclear infiltration potentiate hepatocyte regeneration

Towards real-time topical detection and characterization of FDG dose infiltration prior to PET imaging

Energy Technology Data Exchange (ETDEWEB)

Williams, Jason M.; Arlinghaus, Lori R. [Vanderbilt University Institute of Imaging Science, Vanderbilt University Medical Center, Nashville, TN (United States); Rani, Sudheer D. [Vanderbilt University Institute of Imaging Science, Vanderbilt University Medical Center, Nashville, TN (United States); Vanderbilt University Medical Center, Department of Radiology and Radiological Sciences, Nashville, TN (United States); Shone, Martha D. [Vanderbilt University Medical Center, Department of Radiology and Radiological Sciences, Nashville, TN (United States); Abramson, Vandana G. [Vanderbilt University Medical Center, Department of Medicine, Nashville, TN (United States); Vanderbilt-Ingram Cancer Center, Nashville, TN (United States); Pendyala, Praveen [Vanderbilt University Medical Center, Department of Radiation Oncology, Nashville, TN (United States); Chakravarthy, A.B. [Vanderbilt-Ingram Cancer Center, Nashville, TN (United States); Vanderbilt University Medical Center, Department of Radiation Oncology, Nashville, TN (United States); Gorge, William J.; Knowland, Joshua G.; Lattanze, Ronald K.; Perrin, Steven R. [Lucerno Dynamics, LLC, Morrisville, NC (United States); Scarantino, Charles W. [Lucerno Dynamics, LLC, Morrisville, NC (United States); University of North Carolina, Department of Radiation Oncology, Chapel Hill, NC (United States); Townsend, David W. [Lucerno Dynamics, LLC, Morrisville, NC (United States); Technology and Research-National University of Singapore, Clinical Imaging Research Centre, Agency for Science, Singapore (Singapore); Abramson, Richard G. [Vanderbilt University Institute of Imaging Science, Vanderbilt University Medical Center, Nashville, TN (United States); Vanderbilt University Medical Center, Department of Radiology and Radiological Sciences, Nashville, TN (United States); Vanderbilt-Ingram Cancer Center, Nashville, TN (United States); Yankeelov, Thomas E. [The University of Texas at Austin, Institute for Computational and Engineering Sciences, and Departments of Biomedical Engineering and Internal Medicine, Austin, TX (United States)

2016-12-15

To dynamically detect and characterize {sup 18}F-fluorodeoxyglucose (FDG) dose infiltrations and evaluate their effects on positron emission tomography (PET) standardized uptake values (SUV) at the injection site and in control tissue. Investigational gamma scintillation sensors were topically applied to patients with locally advanced breast cancer scheduled to undergo limited whole-body FDG-PET as part of an ongoing clinical study. Relative to the affected breast, sensors were placed on the contralateral injection arm and ipsilateral control arm during the resting uptake phase prior to each patient's PET scan. Time-activity curves (TACs) from the sensors were integrated at varying intervals (0-10, 0-20, 0-30, 0-40, and 30-40 min) post-FDG and the resulting areas under the curve (AUCs) were compared to SUVs obtained from PET. In cases of infiltration, observed in three sensor recordings (30 %), the injection arm TAC shape varied depending on the extent and severity of infiltration. In two of these cases, TAC characteristics suggested the infiltration was partially resolving prior to image acquisition, although it was still apparent on subsequent PET. Areas under the TAC 0-10 and 0-20 min post-FDG were significantly different in infiltrated versus non-infiltrated cases (Mann-Whitney, p < 0.05). When normalized to control, all TAC integration intervals from the injection arm were significantly correlated with SUV{sub peak} and SUV{sub max} measured over the infiltration site (Spearman ρ ≥ 0.77, p < 0.05). Receiver operating characteristic (ROC) analyses, testing the ability of the first 10 min of post-FDG sensor data to predict infiltration visibility on the ensuing PET, yielded an area under the ROC curve of 0.92. Topical sensors applied near the injection site provide dynamic information from the time of FDG administration through the uptake period and may be useful in detecting infiltrations regardless of PET image field of view. This dynamic information

Towards real-time topical detection and characterization of FDG dose infiltration prior to PET imaging

International Nuclear Information System (INIS)

Williams, Jason M.; Arlinghaus, Lori R.; Rani, Sudheer D.; Shone, Martha D.; Abramson, Vandana G.; Pendyala, Praveen; Chakravarthy, A.B.; Gorge, William J.; Knowland, Joshua G.; Lattanze, Ronald K.; Perrin, Steven R.; Scarantino, Charles W.; Townsend, David W.; Abramson, Richard G.; Yankeelov, Thomas E.

2016-01-01

To dynamically detect and characterize "1"8F-fluorodeoxyglucose (FDG) dose infiltrations and evaluate their effects on positron emission tomography (PET) standardized uptake values (SUV) at the injection site and in control tissue. Investigational gamma scintillation sensors were topically applied to patients with locally advanced breast cancer scheduled to undergo limited whole-body FDG-PET as part of an ongoing clinical study. Relative to the affected breast, sensors were placed on the contralateral injection arm and ipsilateral control arm during the resting uptake phase prior to each patient's PET scan. Time-activity curves (TACs) from the sensors were integrated at varying intervals (0-10, 0-20, 0-30, 0-40, and 30-40 min) post-FDG and the resulting areas under the curve (AUCs) were compared to SUVs obtained from PET. In cases of infiltration, observed in three sensor recordings (30 %), the injection arm TAC shape varied depending on the extent and severity of infiltration. In two of these cases, TAC characteristics suggested the infiltration was partially resolving prior to image acquisition, although it was still apparent on subsequent PET. Areas under the TAC 0-10 and 0-20 min post-FDG were significantly different in infiltrated versus non-infiltrated cases (Mann-Whitney, p < 0.05). When normalized to control, all TAC integration intervals from the injection arm were significantly correlated with SUV_p_e_a_k and SUV_m_a_x measured over the infiltration site (Spearman ρ ≥ 0.77, p < 0.05). Receiver operating characteristic (ROC) analyses, testing the ability of the first 10 min of post-FDG sensor data to predict infiltration visibility on the ensuing PET, yielded an area under the ROC curve of 0.92. Topical sensors applied near the injection site provide dynamic information from the time of FDG administration through the uptake period and may be useful in detecting infiltrations regardless of PET image field of view. This dynamic information may also

The influence of bedrock hydrogeology on catchment-scale nitrate fate and transport in fractured aquifers

Energy Technology Data Exchange (ETDEWEB)

Orr, Alison [Arup, 50 Ringsend Road, Dublin 4 (Ireland); School of Planning, Architecture and Civil Engineering, Queen' s University Belfast (United Kingdom); Nitsche, Janka [RPS, West Pier Business Campus, Dun Laoghaire, Co. Dublin (Ireland); School of Planning, Architecture and Civil Engineering, Queen' s University Belfast (United Kingdom); Archbold, Marie [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast (United Kingdom); Environmental Protection Agency, Richview, Clonskeagh Road, Dublin 14 (Ireland); Deakin, Jenny [Environmental Protection Agency, Richview, Clonskeagh Road, Dublin 14 (Ireland); Department of Civil, Structural and Environmental Engineering, Trinity College Dublin (Ireland); Ofterdinger, Ulrich; Flynn, Raymond [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast (United Kingdom)

2016-11-01

Characterising catchment scale biogeochemical processes controlling nitrate fate in groundwater constitutes a fundamental consideration when applying programmes of measures to reduce risks posed by diffuse agricultural pollutants to water quality. Combining hydrochemical analyses with nitrate isotopic data and physical hydrogeological measurements permitted characterisation of biogeochemical processes influencing nitrogen fate and transport in the groundwater in two fractured bedrock aquifers with contrasting hydrogeology but comparable nutrient loads. Hydrochemical and isotopic analyses of groundwater samples collected from moderately fractured, diffusely karstified limestone indicated nitrification controlled dissolved nitrogen fate and delivery to aquatic receptors. By contrast nitrate concentrations in groundwater were considerably lower in a low transmissivity highly lithified sandstone and pyrite-bearing shale unit with patchy subsoil cover. Geophysical and hydrochemical investigations showed shallower intervals contained hydraulically active fractures where denitrification was reflected through lower nitrogen levels and an isotopic enrichment ratio of 1.7 between δ{sup 15}N and δ{sup 18}O. Study findings highlight the influence of bedrock hydrogeological conditions on aqueous nitrogen mobility. Investigation results demonstrate that bedrock conditions need to be considered when implementing catchment management plans to reduce the impact of agricultural practices on the quality of groundwater and baseflow in receiving rivers. Nitrate isotopic signatures in the groundwater of a freely draining catchment underlain by a karstified aquifer and a poorly draining aquifer with a low transmissivity aquifer. - Graphical abstract: Contrasting nitrate isotope signatures of groundwater in a free draining catchment underlain by a karstified aquifer and a poorly drained catchment underlain by a low transmissivity aquifer. - Highlights: • Comparison of N fate and

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA

Science.gov (United States)

Yang, Qiang; Culbertson, Charles W.; Nielsen, Martha G.; Schalk, Charles W.; Johnson, Carole D.; Marvinney, Robert G.; Stute, Martin; Zheng, Yan

2014-01-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 μg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70-100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93-99%) in particulates (>0.45 μm). These particulates and those settled after a 16-day batch experiment contain 560-13,000 g/kg of As and 14-35% weight/weight of Fe. As/Fe ratios (2.5-20 mmol/mol) and As partitioning ratios (adsorbed/dissolved [As], 20,000-100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ18O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes the oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater.

Bedrock Geologic Map of the Essex Junction Quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital data from VG12-3, Gale, M., Kim. J., and Ruksznis, A., 2012, Bedrock Geologic Map of the essex Junction Quadrangle: Vermont Geological Survey Open File...

Final disposal of spent nuclear fuel in Finnish bedrock. Haestholmen site report

Energy Technology Data Exchange (ETDEWEB)

Anttila, P. [Fortum Engineering Oy, Vantaa (Finland); Ahokas, H. [Fintact Oy, Helsinki (Finland); Front, K. [VTT Communities and Infrastructure, Espoo (Finland)

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Haestholmen. The Haestholmen area is located within the anorogenic Wiborg rapakivi granite batholith, about 1630 million years in age, representing one of the youngest rock formations in Finland. Wiborgite, pyterlite, porphyritic rapakivi granite and even-grained rapakivi granite are the rock types present. 25 bedrock structures have been modelled at the site. Most of them are steeply-dipping fracture zones trending NW-SE and NE-SW, but several sub-horizontal zones, mainly dipping to the N-NE and the SW, are also present. The rock mass between the fracture zones represents what is termed `intact rock`, which is typically hard, unweathered and sparsely fractured. The bedrock structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 8 x 10{sup -6} m{sup 2}/s or 1.3 x 10{sup -6} m{sup 2}/s, depending on how structures are defined. The corresponding mean of the hydraulic conductivity values measured for the intact rock using a 2 m packer interval is 1 x 10{sup -12} m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found in the intact rock. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100-200 m of the bedrock than at greater depths. The groundwater chemistry reflects the post-glacial history of the island of Haestholmen, which rose

Final disposal of spent nuclear fuel in Finnish bedrock. Haestholmen site report

International Nuclear Information System (INIS)

Anttila, P.; Ahokas, H.; Front, K.

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Haestholmen. The Haestholmen area is located within the anorogenic Wiborg rapakivi granite batholith, about 1630 million years in age, representing one of the youngest rock formations in Finland. Wiborgite, pyterlite, porphyritic rapakivi granite and even-grained rapakivi granite are the rock types present. 25 bedrock structures have been modelled at the site. Most of them are steeply-dipping fracture zones trending NW-SE and NE-SW, but several sub-horizontal zones, mainly dipping to the N-NE and the SW, are also present. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The bedrock structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 8 x 10 -6 m 2 /s or 1.3 x 10 -6 m 2 /s, depending on how structures are defined. The corresponding mean of the hydraulic conductivity values measured for the intact rock using a 2 m packer interval is 1 x 10 -12 m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found in the intact rock. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100-200 m of the bedrock than at greater depths. The groundwater chemistry reflects the post-glacial history of the island of Haestholmen, which rose from the Baltic Sea some

Radio Echo Sounding (RES investigations at Talos Dome (East Antarctica: bedrock topography and ice thickness

Directory of Open Access Journals (Sweden)

I. E. Tabacco

2003-06-01

Full Text Available Radio echo sounding measurements were collected during two Antarctic expeditions to determine the ice thickness and the sub-glacial morphology of Talos Dome in the region around 72°48'S; 159°06'E (about 6400 km2 on the edge of the East Antarctic plateau adjacent to Victoria Land in the western Ross Sea sector. The increasing interest in this region is due to the fact that in this area the ice accumulation is higher than in other sites in East Antarctica. Because of this, Talos Dome could be a new site for a project of a deep ice core drilling to obtain information on climate changes near the coast of Antarctica. In this frame, the knowledge of the bedrock topography is of great importance to choose the best location for the drilling site. In this paper, airborne radio echo sounding results from two Antarctic expeditions (1997 and 1999 are presented. Bedrock topography in bi- and three-dimensions for the Talos Dome region are discussed.

Geophysical and hydrogeological characterisation of the impacts of on-site wastewater treatment discharge to groundwater in a poorly productive bedrock aquifer

Energy Technology Data Exchange (ETDEWEB)

Donohue, Shane [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast, David Keir Building, Stranmillis Road, Belfast BT9 5AG, Northern Ireland (United Kingdom); McCarthy, Valerie; Rafferty, Patrick [Department of Applied Sciences, Dundalk Institute of Technology, Dublin Road, Dundalk (Ireland); Orr, Alison; Flynn, Raymond [School of Planning, Architecture and Civil Engineering, Queen' s University Belfast, David Keir Building, Stranmillis Road, Belfast BT9 5AG, Northern Ireland (United Kingdom)

2015-08-01

Contaminants discharging from on-site wastewater treatment systems (OSWTSs) can impact groundwater quality, threatening human health and surface water ecosystems. Risk of negative impacts becomes elevated in areas of extreme vulnerability with high water tables, where thin unsaturated intervals limit vadose zone attenuation. A combined geophysical/hydrogeological investigation into the effects of an OSWTS, located over a poorly productive aquifer (PPA) with thin subsoil cover, aimed to characterise effluent impacts on groundwater. Groundwater, sampled from piezometers down-gradient of the OSWTS percolation area displayed spatially erratic, yet temporally consistent, contaminant distributions. Electrical resistivity tomography identified an area of gross groundwater contamination close to the percolation area and, when combined with seismic refraction and water quality data, indicated that infiltrating effluent reaching the water table discharged to a deeper more permeable zone of weathered shale resting on more competent bedrock. Subsurface structure, defined by geophysics, indicated that elevated chemical and microbiological contaminant levels encountered in groundwater samples collected from piezometers, down-gradient of sampling points with lower contaminant levels, corresponded to those locations where piezometers were screened close to the weathered shale/competent rock interface; those immediately up-gradient were too shallow to intercept this interval, and thus the more impacted zone of the contaminant plume. Intermittent occurrence of faecal indicator bacteria more than 100 m down gradient of the percolation area suggested relatively short travel times. Study findings highlight the utility of geophysics as part of multidisciplinary investigations for OSWTS contaminant plume characterisation, while also demonstrating the capacity of effluent discharging to PPAs to impact groundwater quality at distance. Comparable geophysical responses observed in similar

Geophysical and hydrogeological characterisation of the impacts of on-site wastewater treatment discharge to groundwater in a poorly productive bedrock aquifer

International Nuclear Information System (INIS)

Donohue, Shane; McCarthy, Valerie; Rafferty, Patrick; Orr, Alison; Flynn, Raymond

2015-01-01

Contaminants discharging from on-site wastewater treatment systems (OSWTSs) can impact groundwater quality, threatening human health and surface water ecosystems. Risk of negative impacts becomes elevated in areas of extreme vulnerability with high water tables, where thin unsaturated intervals limit vadose zone attenuation. A combined geophysical/hydrogeological investigation into the effects of an OSWTS, located over a poorly productive aquifer (PPA) with thin subsoil cover, aimed to characterise effluent impacts on groundwater. Groundwater, sampled from piezometers down-gradient of the OSWTS percolation area displayed spatially erratic, yet temporally consistent, contaminant distributions. Electrical resistivity tomography identified an area of gross groundwater contamination close to the percolation area and, when combined with seismic refraction and water quality data, indicated that infiltrating effluent reaching the water table discharged to a deeper more permeable zone of weathered shale resting on more competent bedrock. Subsurface structure, defined by geophysics, indicated that elevated chemical and microbiological contaminant levels encountered in groundwater samples collected from piezometers, down-gradient of sampling points with lower contaminant levels, corresponded to those locations where piezometers were screened close to the weathered shale/competent rock interface; those immediately up-gradient were too shallow to intercept this interval, and thus the more impacted zone of the contaminant plume. Intermittent occurrence of faecal indicator bacteria more than 100 m down gradient of the percolation area suggested relatively short travel times. Study findings highlight the utility of geophysics as part of multidisciplinary investigations for OSWTS contaminant plume characterisation, while also demonstrating the capacity of effluent discharging to PPAs to impact groundwater quality at distance. Comparable geophysical responses observed in similar

Bedrock river erosion measurements and modelling along a river of the Frontal Himalaya

Science.gov (United States)

Lave, Jerome; Dubille, Matthieu

2017-04-01

rate. 2. Both block detachment and attrition processes clearly increase with fluvial shear stress, but non-linearly, in particular through the existence of a minimum threshold. As a result of which bank erosion occur during only a few hours per year during short and very high flood events, which questions the use of average discharge (or drainage area) in many bedrock erosion models. We then propose a semi-physical model of sandstone bars abrasion based on discharge history (HEC-RAS modelling), Rouse suspension model, and experimental measurements on dependency of abrasion rate vs impacting particle size. This model predicts well the timing and the amplitude of both real-time and monsoon average abrasion along the surveyed sandstone bars. This first validation of a model for bank erosion opens large perspective for future work on channel bottom incision modelling using physical models of erosion and their time- and gravel-size-integration, with the objective to introduce more physical rules in landscape evolution models.

The impact of dynamic topography on the bedrock elevation and volume of the Pliocene Antarctic Ice Sheet

Science.gov (United States)

Austermann, Jacqueline; Pollard, David; Mitrovica, Jerry X.; Moucha, Robert; Forte, Alessandro M.; DeConto, Robert M.

2015-04-01

Reconstructions of the Antarctic ice sheet over long timescales (i.e. Myrs) require estimates of bedrock elevation through time. Ice sheet models have accounted, with varying levels of sophistication, for changes in the bedrock elevation due to glacial isostatic adjustment (GIA), but they have neglected other processes that may perturb topography. One notable example is dynamic topography, the deflection of the solid surface of the Earth due to convective flow within the mantle. Numerically predicted changes in dynamic topography have been used to correct paleo shorelines for this departure from eustasy, but the effect of such changes on ice sheet stability is unknown. In this study we use numerical predictions of time-varying dynamic topography to reconstruct bedrock elevation below the Antarctic ice sheet during the mid Pliocene warm period (~3 Ma). Moreover, we couple this reconstruction to a three-dimensional ice sheet model to explore the impact of dynamic topography on the evolution of the Antarctic ice sheet since the Pliocene. Our modeling indicates significant uplift in the area of the Transantarctic Mountains (TAM) and the adjacent Wilkes basin. This predicted uplift, which is at the lower end of geological inferences of uplift of the TAM, implies a lower elevation of the basin in the Pliocene. Relative to simulations that do not include dynamic topography, the lower elevation leads to a smaller Antarctic Ice Sheet volume and a more significant retreat of the grounding line in the Wilkes basin, both of which are consistent with offshore sediment core data. We conclude that reconstructions of the Antarctic Ice Sheet during the mid-Pliocene warm period should be based on bedrock elevation models that include the impact of both GIA and dynamic topography.

Non-uniform overland flow-infiltration model for roadside swales

Science.gov (United States)

García-Serrana, María; Gulliver, John S.; Nieber, John L.

2017-09-01

There is a need to quantify the hydrologic performance of vegetated roadside swales (drainage ditches) as stormwater control measures (SCMs). To quantify their infiltration performance in both the side slope and the channel of the swale, a model has been developed for coupling a Green-Ampt-Mein-Larson (GAML) infiltration submodel with kinematic wave submodels for both overland flow down the side slope and open channel flow for flow in the ditch. The coupled GAML submodel and overland flow submodel has been validated using data collected in twelve simulated runoff tests in three different highways located in the Minneapolis-St. Paul metropolitan area, MN. The percentage of the total water infiltrated into the side slope is considerably greater than into the channel. Thus, the side slope of a roadside swale is the main component contributing to the loss of runoff by infiltration and the channel primarily conveys the water that runs off the side slope, for the typical design found in highways. Finally, as demonstrated in field observations and the model, the fraction of the runoff/rainfall infiltrated (Vi∗) into the roadside swale appears to increase with a dimensionless saturated hydraulic conductivity (Ks∗), which is a function of the saturated hydraulic conductivity, rainfall intensity, and dimensions of the swale and contributing road surface. For design purposes, the relationship between Vi∗ and Ks∗ can provide a rough estimate of the fraction of runoff/rainfall infiltrated with the few essential parameters that appear to dominate the results.

Digital bedrock geologic map of the Cavendish quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-203A Ratcliffe, NM, 1995,�Digital bedrock geologic map of the Cavendish quadrangle, Vermont: USGS Open-File Report 95-203, 2 plates, scale...

Bedrock geologic map of the town of Williston, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG07-4, Kim, J., Gale, M., Thompson, P.J. and Derman, K., 2007, Bedrock geologic map of the town of Williston, Vermont: Vermont Geological Survey...

Bedrock refractive-flow cells: A passive treatment analog to funnel-and-gate

International Nuclear Information System (INIS)

Dick, V.; Edwards, D.

1997-01-01

Funnel-and-gate technology provides a mechanism to passively treat groundwater contaminant plumes, but depends on placement of a sufficient barrier (open-quotes funnelclose quotes) in the plume flow path to channel the plume to a pass-through treatment zone (open-quotes gateclose quotes). Conventional barrier technologies limit funnel-and-gate deployment to unconsolidated overburden applications. A method has been developed which allows similar passive treatment to be applied to bedrock plumes. Rather than use barriers as the funnel, the method uses engineered bedrock zones, installed via precision blasting or other means, to refract groundwater flow along a preferred path to treatment (gate). The method requires orienting the refractive cell based on the Tangent Law and extending refractive cell limbs down gradient of the gate to disperse head and control flow. A typical Refractive-Flow cell may be open-quotes Yclose quotesshaped, with each limb 3-10 ft [1-3 m] wide and several tens to a few hundred feet [10 - 100 m] in length. Treatment takes place at the center of the X. MODFLOW modeling has been used to successfully simulate desired flow. Engineered blasting has been used at full scale application to create bedrock rubble zones for active collection/flow control for several years. The method provides a previously unavailable method to passively treat contaminated groundwater in bedrock at low cost

Denitrification and dilution along fracture flowpaths influence the recovery of a bedrock aquifer from nitrate contamination

International Nuclear Information System (INIS)

Kim, Jonathan J.; Comstock, Jeff; Ryan, Peter; Heindel, Craig; Koenigsberger, Stephan

2016-01-01

In 2000, elevated nitrate concentrations ranging from 12 to 34 mg/L NO_3−N were discovered in groundwater from numerous domestic bedrock wells adjacent to a large dairy farm in central Vermont. Long-term plots and contours of nitrate vs. time for bedrock wells showed “little/no”, “moderate”, and “large” change patterns that were spatially separable. The metasedimentary bedrock aquifer is strongly anisotropic and groundwater flow is controlled by fractures, bedding/foliation, and basins and ridges in the bedrock surface. Integration of the nitrate concentration vs. time data and the physical and chemical aquifer characterization suggest two nitrate sources: a point source emanating from a waste ravine and a non-point source that encompasses the surrounding fields. Once removed, the point source of NO_3 (manure deposited in a ravine) was exhausted and NO_3 dropped from 34 mg/L to 10 mg/L. Our multidisciplinary methods of aquifer characterization are applicable to groundwater contamination in any complexly-deformed and metamorphosed bedrock aquifer. - Highlights: • Bedrock wells contaminated with nitrates at a dairy farm in Vermont, U.S.A. • Nitrate concentration vs. time patterns for wells were spatially separable. • Multidisciplinary aquifer characterization used physical and chemical methods. • Denitrification dominant over dilution along fracture flowpaths • Conceptual model shows exhaustion of a nitrate point-source over 12 years.

Postoperative Analgesia using Bupivacaine Wound Infiltration with ...

African Journals Online (AJOL)

Context: Effective management of postcesarean section (CS) pain is important for the well‑being of mother and child; even in limited‑resource areas, there are drug options which can be explored to achieve this. Aim: This study aimed to compare the analgesic effects of a combination of bupivacaine wound infiltration with ...

Digital bedrock geologic map of the Weston quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG96-526A Ratcliffe, NM�and Burton, WC, 1996,�Digital bedrock geologic map of the Weston quadrangle, Vermont: USGS Open-File Report 96-526, 2...

Digital bedrock geologic map of the Chester quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-576A Ratcliffe, N.M., 1995,�Digital bedrock geologic map of the Chester quadrangle, Vermont: USGS Open-File Report 95-576, 2 plates, scale...

Bedrock Geologic Map of the Jay Peak, VT Quadrangle

Data.gov (United States)

Vermont Center for Geographic Information — Digital data from VG99-1 Compilation bedrock geologic map of the Jay Peak quadrangle, Compiled by B. Doolan, 1999: VGS Open-File Report VG99-1, 1 plate, scale...

Lipid residues preserved in sheltered bedrock features at Gila Cliff Dwellings National Monument, New Mexico

Directory of Open Access Journals (Sweden)

Tammy Buonasera

2016-10-01

Bedrock features represent various economic, social, and symbolic aspects of past societies, but have historically received little study, particularly in North America. Fortunately, new techniques for analyzing spatial configurations, use-wear, and organic residues are beginning to unlock more of the interpretive potential of these features. Though preliminary in nature, the present study contributes to this trend by documenting an application of lipid analysis to bedrock features in a dry rockshelter. Results of this initial application indicate that bedrock features in dry rockshelters may provide especially favorable conditions for the preservation and interpretation of ancient organic residues. Abundant lipids, comparable to concentrations present in some pottery sherds, were extracted from a bedrock grinding surface at Gila Cliff Dwellings National Monument and analyzed using gas chromatography-mass spectrometry. Though the lipids were highly oxidized, degradation products indicative of former unsaturated fatty acids were retained. Comparisons to experimentally aged residues, and absence of a known biomarker for maize, indicate that the bulk of the lipids preserved in the milling surface probably derive from processing an oily nut or seed resource, and not from processing maize. Substantially lower amounts of lipids were recovered from a small, blackened cupule. It is hypothesized that some portion of the lipids in the blackened cupule was deposited from condensed smoke of cooking and heating fires in the caves. Potential for the preservation of organic residues in similar sheltered bedrock contexts is discussed, and a practical method for sampling bedrock features in the field is described.

Analyzing heterogeneous hydrological processes within soil mantle and shallow bedrock in a granitic foothill

Science.gov (United States)

Yamakawa, Y.; Kosugi, K.; Mizuyama, T.; Kinoshita, A.

2011-12-01

In mountainous watersheds, groundwater flowing contributes significantly to runoff generation and plays an important role in the occurrence of landslides. Understanding the hydrological processes within not only the soil mantle but also bedrock is essential for modeling runoff generation and predicting landslides, but it is limited by the physical difficulties of observations. In this study, we conducted intensive in-situ investigations including hydrometric observations using dense borehole well network drilled within soil mantle (central Japan. Groundwater levels in soil mantle showed large spatial and temporal variations in response to rainfall; time lag of peaks between right and left banks in the watershed and localized existences of confined groundwater aquifers. The groundwater movement within soil mantle could be significantly affected by soil mantle structure, i.e., water retention characteristics of soil and soil thickness distributions, as well as groundwater flowing within bedrock. Moreover, the groundwater movement within bedrock also varied considerably with location, which could be controlled by structural condition such as weathering of the bedrock and existence of faults.

Temperature logging of groundwater in bedrock wells for geothermal gradient characterization in New Hampshire, 2012

Science.gov (United States)

Degnan, James; Barker, Gregory; Olson, Neil; Wilder, Leland

2012-01-01

The U.S. Geological Survey, in cooperation with the New Hampshire Geological Survey, measured the fluid temperature of groundwater in deep bedrock wells in the State of New Hampshire in order to characterize geothermal gradients in bedrock. All wells selected for the study had low water yields, which correspond to low groundwater flow from fractures. This reduced the potential for flow-induced temperature changes that would mask the natural geothermal gradient in the bedrock. All the wells included in this study were privately owned, and permission to use the wells was obtained from homeowners before logging.

Digital bedrock geologic map of the Andover quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG96-31A Ratcliffe, N.M., 1996,�Digital bedrock geologic map of the Andover quadrangle, Vermont: USGS Open-File Report 96-31-A, 2 plates, scale...

Digital bedrock geologic map of the Johnson quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-2 Thompson, PJ�and Thompson, TB, 1998,�Digital bedrock geologic map of the Johnson quadrangle, Vermont: VGS Open-File Report VG98-2, 2 plates,...

Digital bedrock geologic map of the Rochester quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG96-33A Walsh, GJ�and Falta, CK, 1996, Digital bedrock geologic map of the Rochester quadrangle, Vermont: USGS Open-File Report 96-33-A, 2 plates,...

Saline groundwater in crystalline bedrock

International Nuclear Information System (INIS)

Lampen, P.

1992-11-01

The State-of-art report describes research made on deep saline groundwaters and brines found in crystalline bedrock, mainly in site studies for nuclear waste disposal. The occurrence, definitions and classifications of saline groundwaters are reviewed with a special emphasis on the different theories concerning the origins of saline groundwaters. Studies of the saline groundwaters in Finland and Sweden have been reviewed more thoroughly. Also the mixing of different bodies of groundwaters, observations of the contact of saline groundwaters and permafrost, and the geochemical modelling of saline groundwaters as well as the future trends of research have been discussed. (orig.)

Digital bedrock geologic map of the Plymouth quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG94-654A Walsh, G.J., and Ratcliffe, N.M., 1994,�Digital bedrock geologic map of the Plymouth quadrangle, Vermont: USGS Open-File Report 94-654, 2...

Digital bedrock geologic map of the Eden quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-3 Kim, J, Springston, G, and Gale, M, 1998,�Digital bedrock geologic map of the Eden quadrangle, Vermont: VGS Open-File Report VG98-3, 2...

The impact of river infiltration on the chemistry of shallow groundwater in a reclaimed water irrigation area.

Science.gov (United States)

Yin, Shiyang; Wu, Wenyong; Liu, Honglu; Bao, Zhe

2016-10-01

Reclaimed water reuse is an effective method of alleviating agricultural water shortages, which entails some potential risks for groundwater. In this study, the impacts of wastewater reuse on groundwater were evaluated by combination of groundwater chemistry and isotopes. In reclaimed water infiltration, salt composition was affected not only by ion exchange and dissolution equilibrium but also by carbonic acid equilibrium. The dissolution and precipitation of calcites and dolomites as well as exchange and adsorption between Na and Ca/Mg were simultaneous, leading to significant changes in Na/Cl, (Ca+Mg)/Cl, electrical conductivity (EC) and sodium adsorption ratio (SAR). The reclaimed water was of the Na-Mg-Ca-HCO 3 -Cl type, and groundwater recharged by reclaimed water was of the Na-Mg-HCO 3 and Mg-Na-HCO 3 types. The hydrogeological conditions characterized by sand-clay alternation led to both total nitrogen (TN) and total phosphorus (TP) removal efficiencies >95%, and there was no significant difference in those contents between aquifers recharged by precipitation and reclamation water. >40years of long-term infiltration and recharge from sewage and reclaimed water did not cause groundwater contamination by nitrogen, phosphorus and heavy metals. These results indicate that characteristics of the study area, such as the lithologic structure with sand-clay alternation, relatively thick clay layer, and relatively large groundwater depth have a significant role in the high vulnerability. Copyright © 2016 Elsevier B.V. All rights reserved.

Simulation of net infiltration and potential recharge using a distributed-parameter watershed model of the Death Valley region, Nevada and California

Science.gov (United States)

Hevesi, Joseph A.; Flint, Alan L.; Flint, Lorraine E.

2003-01-01

This report presents the development and application of the distributed-parameter watershed model, INFILv3, for estimating the temporal and spatial distribution of net infiltration and potential recharge in the Death Valley region, Nevada and California. The estimates of net infiltration quantify the downward drainage of water across the lower boundary of the root zone and are used to indicate potential recharge under variable climate conditions and drainage basin characteristics. Spatial variability in recharge in the Death Valley region likely is high owing to large differences in precipitation, potential evapotranspiration, bedrock permeability, soil thickness, vegetation characteristics, and contributions to recharge along active stream channels. The quantity and spatial distribution of recharge representing the effects of variable climatic conditions and drainage basin characteristics on recharge are needed to reduce uncertainty in modeling ground-water flow. The U.S. Geological Survey, in cooperation with the Department of Energy, developed a regional saturated-zone ground-water flow model of the Death Valley regional ground-water flow system to help evaluate the current hydrogeologic system and the potential effects of natural or human-induced changes. Although previous estimates of recharge have been made for most areas of the Death Valley region, including the area defined by the boundary of the Death Valley regional ground-water flow system, the uncertainty of these estimates is high, and the spatial and temporal variability of the recharge in these basins has not been quantified. To estimate the magnitude and distribution of potential recharge in response to variable climate and spatially varying drainage basin characteristics, the INFILv3 model uses a daily water-balance model of the root zone with a primarily deterministic representation of the processes controlling net infiltration and potential recharge. The daily water balance includes precipitation

Bedrock geology and hydrostratigraphy of the Edwards and Trinity aquifers within the Driftwood and Wimberley 7.5-minute quadrangles, Hays and Comal Counties, Texas

Science.gov (United States)

Clark, Allan K.; Morris, Robert R.

2017-11-16

The Edwards and Trinity aquifers are major sources of water in south-central Texas and are both classified as major aquifers by the State of Texas. The population in Hays and Comal Counties is rapidly growing, increasing demands on the area’s water resources. To help effectively manage the water resources in the area, refined maps and descriptions of the geologic structures and hydrostratigraphic units of the aquifers are needed. This report presents the detailed 1:24,000-scale bedrock hydrostratigraphic map as well as names and descriptions of the geologic and hydrostratigraphic units of the Driftwood and Wimberley 7.5-minute quadrangles in Hays and Comal Counties, Tex.Hydrostratigraphically, the rocks exposed in the study area represent a section of the upper confining unit to the Edwards aquifer, the Edwards aquifer, the upper zone of the Trinity aquifer, and the middle zone of the Trinity aquifer. In the study area, the Edwards aquifer is composed of the Georgetown Formation and the rocks forming the Edwards Group. The Trinity aquifer is composed of the rocks forming the Trinity Group. The Edwards and Trinity aquifers are karstic with high secondary porosity along bedding and fractures. The Del Rio Clay is a confining unit above the Edwards aquifer and does not supply appreciable amounts of water to wells in the study area.The hydrologic connection between the Edwards and Trinity aquifers and the various hydrostratigraphic units is complex because the aquifer system is a combination of the original Cretaceous depositional environment, bioturbation, primary and secondary porosity, diagenesis, and fracturing of the area from Miocene faulting. All of these factors have resulted in development of modified porosity, permeability, and transmissivity within and between the aquifers. Faulting produced highly fractured areas which allowed for rapid infiltration of water and subsequently formed solutionally enhanced fractures, bedding planes, channels, and caves that

Hydrogeology and groundwater quality of the glaciated valleys of Bradford, Tioga, and Potter Counties, Pennsylvania

Science.gov (United States)

Williams, John H.; Taylor, Larry E.; Low, Dennis J.

1998-01-01

The most important sources of groundwater in Bradford, Tioga, and Potter Counties are the stratified-drift aquifers. Saturated sand and gravel primarily of outwash origin forms extensive unconfined aquifers in the valleys. Outwash is underlain in most major valleys by silt, clay, and very fine sand of lacustrine origin that comprise extensive confining units. The lacustrine confining units locally exceed 100 feet in thickness. Confined aquifers of ice-contact sand and gravel are buried locally beneath the lacustrine deposits. Bedrock and till are the basal confining units of the stratifies-drift aquifer systems. Recharge to the stratified-drift aquifers if by direct infiltration of precipitation, tributary-stream infiltration, infiltration of unchanneled runoff at the valley walls, and groundwater inflow from the bedrock and till uplands. Valley areas underlain by superficial sand and gravel contribute about 1 million gallons per day per square mile of water from precipitation to the aquifers. Tributary streams provide recharge of nearly 590 gallons per day per foot of stream reach. Water is added at the rate of 1 million gallons per day per square mile of bordering uplands not drained by tributary streams to the stratified-drift aquifers from unchanneled runoff and groundwater inflow. Induced infiltration can be a major source of recharge to well fields completed in unconfined stratified-drift aquifers that are in good hydraulic connection with surface water. The well fields of an industrial site in North Towanda, a public-water supplier at Tioga Point, and the U.S. Fish and Wildlife Service at Asaph accounted for 75 percent of the 10.8 million gallons per day pf groundwater withdrawn by public suppliers and other selected users in 1985. The well fields tap stratified-drift aquifers that are substantially recharged by induced infiltration or tributary-stream infiltration. Specific-capacity data from 95 wells indicate that most wells completed in stratified

Seasonal changes of the infiltration rates in urban parks of Valencia City, Eastern Spain

Science.gov (United States)

Cerdà, Artemi; Keesstra, Saskia; Burguet, María; Pereira, Paulo; Esteban Lucas-Borja, Manuel; Martinez-Murillo, Juan F.

2016-04-01

Infiltration is a key process of the hydrological cycle. Infiltration also controls the soil water resources, and the development of the vegetation, and moreover, in the Mediterranean, determines the runoff generation (Cerdà, 1996; 1997; 2001). In the Mediterranean, the infiltration in forest soils shows high spatial variability and seasonal and temporal changes (Cerdà, 1999; Bodí and Cerdà, 2009) and is being affected by forest fires (Cerdà, 1998), which introduce a new temporal change in the seasonality of the infiltration rates. Although the forest soils are well assessed, there is no information about the infiltration in urban areas in Mediterranean cities. The Mediterranean dense urban systems use to be treated as impermeable areas. However, the cities show areas covered by vegetation and with soils that allow the rainfall to infiltrate. Those areas are mainly the parks. In order to shed some light on the infiltration capacity of the soils of the urban area of Valencia city 30 rainfall simulations experiments (Cerdà, 1996) and 90 ring infiltrometer (10 cm diameter) measurements were carried out in January 2011, and they were repeated in July 2011, to compare wet (19.4 % of soil moisture) and dry (5.98 % of soil moisture) soils. The infiltration curves where fitted to the Horton (1933) equation and they lasted for 1 hour. The results show that the infiltration is 11 times higher when measured with ring infiltrometer than with the simulated rainfall at 55 mmh-1, and that the infiltration rates where higher in summer than in winter: 2.01 higher for the ring infiltrometer, and 1.45 higher when measured with the rainfall simulator. In comparison to the soils from the forest areas, the infiltration rate in the gardens were lower, with values of 10.23 and 21.65 mm h-1 in average for winter and summer when measured with the rainfall simulator. Similar results were found with the ring infiltrometer. It was also found a clear relationship between the vegetation

On the estimation of threshold pressures in infiltration of liquid metals into particle preforms

International Nuclear Information System (INIS)

Molina, J.M.; Prieto, R.; Duarte, M.; Narciso, J.; Louis, E.

2008-01-01

Threshold pressures for infiltration of different metals into preforms of ceramic particles of various nature and morphology were experimentally determined and the results compared with those estimated by using the specific particle surface areas derived from laser diffraction and gas adsorption. Whilst laser diffraction provides an under estimation of the areas involved in the infiltration experiments, and thus of threshold pressures, gas adsorption offers reasonable values for particles that are regular and free of nanostructured surfaces

Denitrification and dilution along fracture flowpaths influence the recovery of a bedrock aquifer from nitrate contamination

Energy Technology Data Exchange (ETDEWEB)

Kim, Jonathan J., E-mail: jon.kim@vermont.gov [Vermont Geological Survey, 1 National Life Drive, Main 2, Montpelier, VT 05620 (United States); Comstock, Jeff [Vermont Agency of Agriculture, 116 State Street, Montpelier, VT 05620 (United States); Ryan, Peter [Dept. of Geology, Middlebury College, Middlebury, VT 05753 (United States); Heindel, Craig [Waite-Heindel Environmental Management, 7 Kilburn Street, Suite 301, Burlington, VT 05401 (United States); Koenigsberger, Stephan [Dept. of Geology, Middlebury College, Middlebury, VT 05753 (United States)

2016-11-01

In 2000, elevated nitrate concentrations ranging from 12 to 34 mg/L NO{sub 3}−N were discovered in groundwater from numerous domestic bedrock wells adjacent to a large dairy farm in central Vermont. Long-term plots and contours of nitrate vs. time for bedrock wells showed “little/no”, “moderate”, and “large” change patterns that were spatially separable. The metasedimentary bedrock aquifer is strongly anisotropic and groundwater flow is controlled by fractures, bedding/foliation, and basins and ridges in the bedrock surface. Integration of the nitrate concentration vs. time data and the physical and chemical aquifer characterization suggest two nitrate sources: a point source emanating from a waste ravine and a non-point source that encompasses the surrounding fields. Once removed, the point source of NO{sub 3} (manure deposited in a ravine) was exhausted and NO{sub 3} dropped from 34 mg/L to < 10 mg/L after ~ 10 years; however, persistence of NO{sub 3} in the 3 to 8 mg/L range (background) reflects the long term flux of nitrates from nutrients applied to the farm fields surrounding the ravine over the years predating and including this study. Inferred groundwater flow rates from the waste ravine to either moderate change wells in basin 2 or to the shallow bedrock zone beneath the large change wells are 0.05 m/day, well within published bedrock aquifer flow rates. Enrichment of {sup 15}N and {sup 18}O in nitrate is consistent with lithotrophic denitrification of NO{sub 3} in the presence of dissolved Mn and Fe. Once the ravine point-source was removed, denitrification and dilution collectively were responsible for the down-gradient decrease of nitrate in this bedrock aquifer. Denitrification was most influential when NO{sub 3}−N was > 10 mg/L. Our multidisciplinary methods of aquifer characterization are applicable to groundwater contamination in any complexly-deformed and metamorphosed bedrock aquifer. - Highlights: • Bedrock wells contaminated

Monitoring the bedrock stability in Olkiluoto. Summary of campaign based GPS measurements in 1996-2011

International Nuclear Information System (INIS)

Nyberg, S.; Kallio, U.; Haekli, P.; Jokela, J.; Koivula, H.; Saaranen, V.; Rouhiainen, P.

2013-12-01

The Finnish Geodetic Institute has monitored crustal deformations in Olkiluoto since mid-1990s. This is a final report of campaign based GPS measurements carried out in 1996-2011. The aim of the research has been monitoring the bedrock stability in the Olkiluoto area. The research were started in 1995, when a local GPS network of ten pillars, called inner network, was established on Olkiluoto Island. The research area was expanded in 2003- 2005 with four new pillars (outer network) established at 5-10 km distances from the inner network. One of the pillar points is the Olkiluoto permanent GPS station. Regular biannual measurement campaigns have been carried out on other pillar points

Seismic tomography Technology for the Water Infiltration Experiment

International Nuclear Information System (INIS)

Descour, J.

2001-01-01

NSA Engineering, Inc., conducted seismic tomography surveys in Niche No.3 in the Exploratory Studies Facility (ESF), Yucca Mountain, Nevada, and Alcove No.8 in the Enhanced Characterization of the Repository Block (ECRB) cross drift as part of the Infiltration Experiment being conducted in Niche No.3. NSA Engineering is a direct support contractor to the Yucca Mountain Project. This report documents the work performed from August 14 through 30, 2000, prior to the beginning of the infiltration experiment. The objective of the seismic tomography survey was to investigate the flow path of water between access drifts and more specifically to (Kramer 2000): (1) Conduct a baseline seismic tomography survey prior to the infiltration experiment; (2) Produce 2-D and 3-D tomographic images of the rock volume between Alcove No.8 and Niche No.3; (3) Correlate tomography results with published structural and lithological features, and with other geophysical data such as ground penetrating radar (GPR); and (4) Results of this survey will form a baseline with which to compare subsequent changes to the rock mass. These changes may be as a result of the water infiltration tests that could be conducted in Alcove No.8 in 2001. The scope of this reported work is to use the velocity tomograms to: (a) assess the structures and lithologic features within the surveyed area and/or volume between the two access drifts; and (b) provide information on the structural state of the rock mass as inferred by the velocity signatures of the rock prior to the beginning of the infiltration experiment

Study on the Effectiveness of Infiltration Wells to Reduce Excess Surface Run Off In ITB

Directory of Open Access Journals (Sweden)

Mardiah Afifah Muhsinatu

2018-01-01

Full Text Available Institut Teknologi Bandung (ITB, Ganesha Campus, Indonesia, has an area of 28.86 hectares. The campus is located in Bandung. Starting from 2012, new buildings were constructed within the area, reducing the area of permeable surface significantly. In the past few years, there were several excess run off incidents in the campus. The insufficient area of permeable surface as well as the inadequate capacity of the drainage system contributes to the excess surface run off. The drainage system has only two outlets. Moreover, in some areas, the drainage systems are disconnected. Thus, most the surface run off are stored within the drainage system. The purpose of this study is to evaluate the effectiveness of infiltration wells for reducing the local excess run off in ITB. Precipitation data and drained service area are used to estimate the design discharge from each building in ITB. In order to avoid the excess surface run off of certain locations in ITB, then the infiltration wells are proposed to balance the area of impermeable surface. The effectiveness of the infiltration wells are evaluated by assessing their number to their contribution in reducing the excess surface runs off.

Detection of lymphomatous infiltration in the bone marrow

International Nuclear Information System (INIS)

Cunha, M. O.; Santos, A. O.; Costa, S.C.; Ramos, C.D.; Etchebehere, E.C.S.C.; Metze, I.L.; Barbosa, M.N.S.; Souza, C.A.; Camargo, E.E.

1997-01-01

Full text: The scintillographic follow-up of patients with lymphoma is obtained by making whole body research (WBR) with gallium-67. However, the abnormal accumulation of this pharmaceutical in the long bones is not an specific for lymphomatous infiltration and can be representative of hematopoietic expansion of bone marrow, as well. The differential diagnosis can be done using bone scintillography (BS) and bone marrow scintillography (BMS). We present a case where the diagnosis of lymphomatous infiltration indicated by the WBR with gallium-67, was confirmed by the BS and BMS. Male patient, 57 years old, with diagnosis of a high level malignant non-Hodgkin lymphoma, was submitted to the WBR with gallium-67 during the chemotherapy. The gallium-67 was high uptaked in the third distal of the right femur and in the proximal of the right tibia. One month after finishing the chemotherapy, a new WBR with gallium-67 shows the persistence of the high uptake in the same areas and the appearance of new ones in the third distal of the left femur. The study was complemented with BS and BMS. The BS revealed high uptake in focal areas, in the same regions where high uptake of gallium-67 has been detected in the study, after chemotherapy. The BMS showed absence of functioning bone marrow in these areas reducing the probability of medullar expansion. The absence of answering to the chemotherapy has been verified, changing the patient behavior and prognostic. The BMS with colloidal Tc-99m sulfur in this patient was useful for the differential diagnosis between medullar expansion and lymphomatous medullar infiltration

Digital bedrock geologic map of the Saxtons River quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG96-52A Ratcliffe, NM�and Armstrong, TR, 1996, Digital bedrock geologic map of the Saxtons River quadrangle, Vermont, USGS Open-File Report...

Greenland 5 km DEM, Ice Thickness, and Bedrock Elevation Grids

Data.gov (United States)

National Aeronautics and Space Administration — A Digital Elevation Model (DEM), ice thickness grid, and bedrock elevation grid of Greenland acquired as part of the PARCA program are available in ASCII text format...

Significance of Thermal Fluvial Incision and Bedrock Transfer due to Ice Advection on Greenland Ice Sheet Topography

Science.gov (United States)

Crozier, J. A.; Karlstrom, L.; Yang, K.

2017-12-01

Ice sheet surface topography reflects a complicated combination of processes that act directly upon the surface and that are products of ice advection. Using recently-available high resolution ice velocity, imagery, ice surface elevation, and bedrock elevation data sets, we seek to determine the domain of significance of two important processes - thermal fluvial incision and transfer of bedrock topography through the ice sheet - on controlling surface topography in the ablation zone. Evaluating such controls is important for understanding how melting of the GIS surface during the melt season may be directly imprinted in topography through supraglacial drainage networks, and indirectly imprinted through its contribution to basal sliding that affects bedrock transfer. We use methods developed by (Karlstrom and Yang, 2016) to identify supraglacial stream networks on the GIS, and use high resolution surface digital elevation models as well as gridded ice velocity and melt rate models to quantify surface processes. We implement a numerically efficient Fourier domain bedrock transfer function (Gudmundsson, 2003) to predict surface topography due to ice advection over bedrock topography obtained from radar. Despite a number of simplifying assumptions, the bedrock transfer function predicts the observed ice sheet surface in most regions of the GIS with ˜90% accuracy, regardless of the presence or absence of supraglacial drainage networks. This supports the hypothesis that bedrock is the most significant driver of ice surface topography on wavelengths similar to ice thickness. Ice surface topographic asymmetry on the GIS is common, with slopes in the direction of ice flow steeper than those faced opposite to ice flow, consistent with bedrock transfer theory. At smaller wavelengths, topography consistent with fluvial erosion by surface hydrologic features is evident. We quantify the effect of ice advection versus fluvial thermal erosion on supraglacial longitudinal stream

Geohydrology of the Gallup's Quarry area, Plainfield, Connecticut

Science.gov (United States)

Melvin, Robert L.; Stone, Janet Radway; Craft, Patrick A.; Lane, John W.

1995-01-01

The geohydrology of the Gallup's Quarry area in Plainfield, Connecticut was characterized by the U.S. Geological Survey, in cooperation with the U.S. Environmental Protection Agency, to provide a preliminary framework for future remedial efforts. Gallup's Quarry, an inactive sand and gravel pit, was the site of unregulated disposal of an unknown volume of chemical wastes from at least the summer of 1977 until January 1978. Existing information collected for the Connecticut Department of Environmental Protection during 1978-82 showed that ground water beneath Gallup's Quarry and adjacent land to the northwest was contaminated by organic and inorganic compounds. There is also some evidence for contamination of Mill Brook, which is located north and northwest of the disposal areas. Geologic mapping and subsurface data show that unconsolidated surficial materials up to 90 feet thick overlie fractured crystalline bedrock in most of the Gallup's Quarry area. The surficial materials consist primarily of stratified drift and till. Texture changes vertically and laterally within the stratified drift; grain size ranges from very coarse to fine. Till blankets the bedrock surface beneath the stratified drift and is a few feet to as much as 25 feet thick. Bedrock is exposed at land surface in a hill in the southeastern part of the quarry and slopes to depths of up to 90 feet beneath the area west and north of the disposal sites. The bedrock is a dark, fine-grained, fractured and jointed blastomylonite and hornblende gneiss of the Quinebaug Formation. It is likely that a west- northwest-trending fault is present in the bedrock beneath Gallup's Quarry; this fault, if present, may provide a preferential pathway for ground-water flow and contaminant transport. The principal horizontal direction of ground-water flow and movement of dissolved contaminants in the stratified drift was to the northwest of the waste-disposal areas toward Mill Brook in 1978. Estimates of average annual

Mixed artificial grasslands with more roots improved mine soil infiltration capacity

Science.gov (United States)

Wu, Gao-Lin; Yang, Zheng; Cui, Zeng; Liu, Yu; Fang, Nu-Fang; Shi, Zhi-Hua

2016-04-01

Soil water is one of the critical limiting factors in achieving sustainable revegetation. Soil infiltration capacity plays a vital role in determining the inputs from precipitation and enhancing water storage, which are important for the maintenance and survival of vegetation patches in arid and semi-arid areas. Our study investigated the effects of different artificial grasslands on soil physical properties and soil infiltration capacity. The artificial grasslands were Medicago sativa, Astragalus adsurgens, Agropyron mongolicum, Lespedeza davurica, Bromus inermis, Hedysarum scoparium, A. mongolicum + Artemisia desertorum, A. adsurgens + A. desertorum and M. sativa + B. inermis. The soil infiltration capacity index (SICI), which was based on the average infiltration rate of stage I (AIRSI) and the average infiltration rate of stage III (AIRS III), was higher (indicating that the infiltration capacity was greater) under the artificial grasslands than that of the bare soil. The SICI of the A. adsurgens + A. desertorum grassland had the highest value (1.48) and bare soil (-0.59) had the lowest value. It was evident that artificial grassland could improve soil infiltration capacity. We also used principal component analysis (PCA) to determine that the main factors that affected SICI were the soil water content at a depth of 20 cm (SWC20), the below-ground root biomasses at depths of 10 and 30 cm (BGB10, BGB30), the capillary porosity at a depth of 10 cm (CP10) and the non-capillary porosity at a depth of 20 cm (NCP20). Our study suggests that the use of Legume-poaceae mixtures and Legume-shrub mixtures to create grasslands provided an effective ecological restoration approach to improve soil infiltration properties due to their greater root biomasses. Furthermore, soil water content, below-ground root biomass, soil capillary porosity and soil non-capillary porosity were the main factors that affect the soil infiltration capacity.

Knickpoint retreat and transient bedrock channel morphology triggered by base-level fall in small bedrock river catchments: The case of the Isle of Jura, Scotland

Science.gov (United States)

Castillo, Miguel; Bishop, Paul; Jansen, John D.

2013-01-01

A sudden drop in river base-level can trigger a knickpoint that propagates throughout the fluvial network causing a transient state in the landscape. Knickpoint retreat has been confirmed in large fluvial settings (drainage areas > 100 km2) and field data suggest that the same applies to the case of small bedrock river catchments (drainage areas UK), where rivers incise into dipping quartzite. The mapping of raised beach deposits and strath terraces, and the analysis of stream long profiles, were used to identify knickpoints that had been triggered by base-level fall. Our results indicate that the distance of knickpoint retreat scales to the drainage area in a power law function irrespective of structural setting. On the other hand, local channel slope and basin size influence the vertical distribution of knickpoints. As well, at low drainage areas (~ 4 km2) rivers are unable to absorb the full amount of base-level fall and channel reach morphology downstream of the knickpoint tends towards convexity. The results obtained here confirm that knickpoint retreat is mostly controlled by stream discharge, as has been observed for other transient landscapes. Local controls, reflecting basin size and channel slope, have an effect on the vertical distribution of knickpoints; such controls are also related to the ability of rivers to absorb the base-level fall.

High Severity Wildfire Effect On Rainfall Infiltration And Runoff: A Cellular Automata Based Simulation

Science.gov (United States)

Vergara-Blanco, J. E.; Leboeuf-Pasquier, J.; Benavides-Solorio, J. D. D.

2017-12-01

A simulation software that reproduces rainfall infiltration and runoff for a storm event in a particular forest area is presented. A cellular automaton is utilized to represent space and time. On the time scale, the simulation is composed by a sequence of discrete time steps. On the space scale, the simulation is composed of forest surface cells. The software takes into consideration rain intensity and length, individual forest cell soil absorption capacity evolution, and surface angle of inclination. The software is developed with the C++ programming language. The simulation is executed on a 100 ha area within La Primavera Forest in Jalisco, Mexico. Real soil texture for unburned terrain and high severity wildfire affected terrain is employed to recreate the specific infiltration profile. Historical rainfall data of a 92 minute event is used. The Horton infiltration equation is utilized for infiltration capacity calculation. A Digital Elevation Model (DEM) is employed to reproduce the surface topography. The DEM is displayed with a 3D mesh graph where individual surface cells can be observed. The plot colouring renders water content development at the cell level throughout the storm event. The simulation shows that the cumulative infiltration and runoff which take place at the surface cell level depend on the specific storm intensity, fluctuation and length, overall terrain topography, cell slope, and soil texture. Rainfall cumulative infiltration for unburned and high severity wildfire terrain are compared: unburned terrain exhibits a significantly higher amount of rainfall infiltration.It is concluded that a cellular automaton can be utilized with a C++ program to reproduce rainfall infiltration and runoff under diverse soil texture, topographic and rainfall conditions in a forest setting. This simulation is geared for an optimization program to pinpoint the locations of a series of forest land remediation efforts to support reforestation or to minimize runoff.

Ice/Bedrock Feedbacks as a Principle Contributor to Glacial-Interglacial Oscillations

Science.gov (United States)

Kimmel, J.; Lee, K.; Jackson, C. H.

2014-12-01

Since the mid-Pleistocene, the oscillation between glacial and interglacial climate states occurs with a period of approximately 100 kyr. Each cycle is comprised of a slow glaciation with a subsequent rapid deglaciation. While the solar forcing is clearly an important driver for these transitions, the power spectrum of the solar forcing is quite different from the subsequent climate response and, in general, does not have a noticeable correlation with global ice volume. Instead, previous studies have shown that internal climate processes and their interactions (e.g., CO2, water vapor, isostatic bed response) play a significant role in producing these global climate cycles. The rapid retreat of large ice sheets at the start of an interglacial is often attributed to the interaction between surface and atmospheric processes. While calving is thought to amplify this retreat, it is not typically considered a principle driver of the ice sheet response. Our study investigates the potential for ice/bedrock feedbacks to be a principle contributor in shaping the glacial-interglacial climate oscillation -- particularly the rapid deglaciation that precedes an interglacial. The ice sheet model we develop includes a piecewise linear ice/bedrock feedback while atmospheric and surface processes are taken to be as simple as possible. Due to the long timescale of the bedrock response and the rapid mass loss due to calving, the model ice sheet exhibits rapid deglaciation from a stable maximum when it retreats through an overdeepening. However, ice sheet advance is also shown to be as rapid unless a more complex bedrock response is considered. In particular, we show that a forebulge created by the displacement of the mantle adds a new stable branch to the volume/equilibrium line bifurcation diagram that results in slower growth of the ice sheet during glaciation.

Reflection seismic studies in the Forsmark area - stage 1

Energy Technology Data Exchange (ETDEWEB)

Juhlin, Christopher; Bergman Bjoern; Palm, Hans [Uppsala Univ. (Sweden). Dept. of Earth Sciences

2002-10-01

Reflection seismic data were acquired in the Spring of 2002 in the Forsmark area, located about 70 km northeast of Uppsala, Sweden. The Forsmark area has been targeted by SKB as a possible storage site for high level radioactive waste. About 16 km of high resolution seismic data were acquired along five separate profiles varying in length from 2 to 5 km. Non-final source and receiver spacing was 10 m with 100 active channels when recording data from a dynamite source (15-75 g). The profiles were located within a relatively undeformed lens of bedrock that trends in the NW-SE direction. The lens is surrounded by highly deformed rock on all sides. In conjunction with the reflection component of the study, all shots were also recorded on up to eleven 3-component fixed Orion seismographs. These recordings provided long offset data from which a velocity model of the uppermost 400 m of bedrock could be derived. Results from the study show that the bedrock has been well imaged down to depths of at least 3 km. The upper 1000 m of bedrock is much more reflective in the southeastern portion of the lens compared to the northwestern part close to the Forsmark reactors. This is interpreted as the bedrock being more homogeneous in the northwest. However, a major reflective zone (the A1 reflector) is interpreted to dip to the S-SE below this homogeneous bedrock. In the southeastern portion of the lens the orientation of the reflectors is well determined where the profiles cross one another. The general strike of the major reflectors is NE-SW with dips of 20-35 degrees to the southeast.

Estimated Depth to Bedrock of Iowa as a 110 meter pixel_32bit Imagine Format Raster Dataset

Data.gov (United States)

Iowa State University GIS Support and Research Facility — This raster dataset represents the depth to bedrock from the land surface. It was derived by subtracting a bedrock surface elevation layer from the NED 30 meter...

Digital bedrock geologic map of the Morrisville quadrangle,�Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-1 Springston, G., Kim, J., and Applegate, G.S., 1998,�Digital bedrock geologic map of the Morrisville quadrangle,�Vermont: VGS Open-File...

Digital compilation bedrock geologic map of the Milton quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-8A Dorsey, R, Doolan, B, Agnew, PC, Carter, CM, Rosencrantz, EJ, and Stanley, RS, 1995, Digital compilation bedrock geologic map of the Milton...

Chemical weathering as a mechanism for the climatic control of bedrock river incision

Science.gov (United States)

Murphy, Brendan P.; Johnson, Joel P. L.; Gasparini, Nicole M.; Sklar, Leonard S.

2016-04-01

Feedbacks between climate, erosion and tectonics influence the rates of chemical weathering reactions, which can consume atmospheric CO2 and modulate global climate. However, quantitative predictions for the coupling of these feedbacks are limited because the specific mechanisms by which climate controls erosion are poorly understood. Here we show that climate-dependent chemical weathering controls the erodibility of bedrock-floored rivers across a rainfall gradient on the Big Island of Hawai‘i. Field data demonstrate that the physical strength of bedrock in streambeds varies with the degree of chemical weathering, which increases systematically with local rainfall rate. We find that incorporating the quantified relationships between local rainfall and erodibility into a commonly used river incision model is necessary to predict the rates and patterns of downcutting of these rivers. In contrast to using only precipitation-dependent river discharge to explain the climatic control of bedrock river incision, the mechanism of chemical weathering can explain strong coupling between local climate and river incision.

Geophysical logging of bedrock wells for geothermal gradient characterization in New Hampshire, 2013

Science.gov (United States)

Degnan, James R.; Barker, Gregory; Olson, Neil; Wilder, Leland

2014-01-01

The U.S. Geological Survey, in cooperation with the New Hampshire Geological Survey, measured the fluid temperature of groundwater and other geophysical properties in 10 bedrock wells in the State of New Hampshire in order to characterize geothermal gradients in bedrock. The wells selected for the study were deep (five ranging from 375 to 900 feet and five deeper than 900 feet) and 6 had low water yields, which correspond to low groundwater flow from fractures. This combination of depth and low water yield reduced the potential for flow-induced temperature changes that would mask the natural geothermal gradient in the bedrock. All the wells included in this study are privately owned, and permission to use the wells was obtained from landowners before geophysical logs were acquired for this study. National Institute of Standards and Technology thermistor readings were used to adjust the factory calibrated geophysical log data. A geometric correction to the gradient measurements was also necessary due to borehole deviation from vertical.

Final disposal of spent nuclear fuel in Finnish bedrock - Romuvaara site report

Energy Technology Data Exchange (ETDEWEB)

Anttila, P. [Fortum Engineering Oy (Finland); Ahokas, H. [Fintact Oy (Finland); Front, K. [VTT Communities and Infrastructure, Espoo (Finland)] [and others

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Romuvaara. The bedrock of Romuvaara belongs to the Archean basement complex, whose oldest parts date back over 2800 million years. The bedrock consists mainly of migmatitic banded gneisses (tonalite, leucotonalite and mica gneiss), which are cut by granodiorite and metadiabase dykes. The rocks, excluding the metadiabase, have undergone a polyphase Archaean deformation. Altogether 31 bedrock structures (R-structures) have been modelled at the investigation site, most of them representing steeply dipping fracture zones. The rock mass between the fracture zones represents what is termed `intact rock`, which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 1.6 x 10{sup -7} m{sup 2}/s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval is 8 x 10{sup -12} m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found, for both the R-structures and the intact rock. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater of Romuvaara is classified as fresh water and the Total Dissolved Solids (TDS) and chloride contents increase with depth. The chemically

Final disposal of spent nuclear fuel in Finnish bedrock - Romuvaara site report

International Nuclear Information System (INIS)

Anttila, P.; Ahokas, H.; Front, K.

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Romuvaara. The bedrock of Romuvaara belongs to the Archean basement complex, whose oldest parts date back over 2800 million years. The bedrock consists mainly of migmatitic banded gneisses (tonalite, leucotonalite and mica gneiss), which are cut by granodiorite and metadiabase dykes. The rocks, excluding the metadiabase, have undergone a polyphase Archaean deformation. Altogether 31 bedrock structures (R-structures) have been modelled at the investigation site, most of them representing steeply dipping fracture zones. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 1.6 x 10 -7 m 2 /s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval is 8 x 10 -12 m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found, for both the R-structures and the intact rock. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater of Romuvaara is classified as fresh water and the Total Dissolved Solids (TDS) and chloride contents increase with depth. The chemically most evolved

Bedrock neutralization study for the Bruin Lagoon Superfund Site

International Nuclear Information System (INIS)

Patelunas, G.M.; Lenhardt, D.R.; Niece, J.E.

1989-01-01

The Bruin Lagoon site is located in Bruin Butler County, Pennsylvania, and is listed as No. 3 on the U.S. Environmental Protection Agencies' National Priority List. The Lagoon contains waste petroleum tars, sulfuric acid, coal combustion ash, spent bauxite and other waste materials. This paper reports on the bedrock neutralization study, conducted to assess the feasibility of injecting caustic solutions into acid-contaminated bedrock beneath the lagoon. The site is underlain by a fine to medium grain quartz sandstone which is contaminated with acid to depths in excess of 30 feet. For this investigation, Nx-cores were obtained and pressure tests conducted to a depth of 30 feet below the top of rock. Leach tests were conducted on contaminated core sections using sodium hydroxide and sodium carbonate solutions. A total of 12 core sections were exposed in 3-inch diameter test cylinders and permeated under a positive pressure of 25 to 50 psi. Measurements of leachate volume, temperature, pH, and hydraulic conductivity were recorded

Digital compilation bedrock geologic map of the Lincoln quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-5A Stanley, R, DelloRusso, V, Haydock, S, Lapp, E, O'Loughlin, S, Prewitt, J,and Tauvers, PR, 1995, Digital compilation bedrock geologic map...

Diffuse infiltrating retinoblastoma invading subarachnoid space

Directory of Open Access Journals (Sweden)

Kase S

2011-06-01

Full Text Available Satoru Kase1, Kazuhiko Yoshida1, Shigenobu Suzuki2, Koh-ichi Ohshima3, Shigeaki Ohno4, Susumu Ishida11Department of Ophthalmology, Hokkaido University Graduate School of Medicine, Sapporo; 2Department of Ophthalmic Oncology, National Cancer Center Hospital, Tokyo; 3Section of Ophthalmology, Okayama Medical Center, Okayama; 4Department of Ocular Inflammation and Immunology, Hokkaido University Graduate School of Medicine, Sapporo, JapanAbstract: We report herein an unusual case of diffuse infiltrating retinoblastoma involving the brain, which caused a patient’s death 27 months after enucleation. An eight-year-old boy complained of blurred vision in his right eye (OD in October 2006. Funduscopic examination showed optic disc swelling, dense whitish vitreous opacity, and an orange-colored subretinal elevated lesion adjacent to the optic disc. Fluorescein angiography revealed hyperfluorescence in the peripapillary region at an early-phase OD. Because the size of the subretinal lesion and vitreous opacity gradually increased, he was referred to us. His visual acuity was 20/1000 OD on June 20, 2007. Slit-lamp biomicroscopy showed a dense anterior vitreous opacity. Ophthalmoscopically, the subretinal orange-colored area spread out until reaching the mid peripheral region. A B-mode sonogram and computed tomography showed a thick homogeneous lesion without calcification. Gadolinium-enhanced magnetic resonance imaging showed a markedly enhanced appearance of the underlying posterior retina. Enucleation of the right eye was performed nine months after the initial presentation. Histopathology demonstrated retinal detachment and a huge choroidal mass invading the optic nerve head. The tumor was consistent with diffuse infiltrating retinoblastoma. The patient died due to brain involvement 27 months after enucleation. Ophthalmologists should be aware that diffuse infiltrating retinoblastoma may show an unfavorable course if its diagnosis is delayed

Short-term evaluation of non-absorbable microgranular hydroxyapatite infiltration in the guinea pig subepidermal abdominal region

Directory of Open Access Journals (Sweden)

A.P. Xavier

2002-01-01

Full Text Available Non-absorbable microgranular hydroxyapatite was infiltrated into the subepidermal abdominal region of guinea pigs in order to assess the possibility of using this material to correct deficiencies in orbital volume. Microgranular hydroxyapatite (2.0 ml was subepidermally infiltrated into the abdominal region of 20 guinea pigs. The animals were divided into four experimental groups of 5 animals each, which were killed 7 (G1, 15 (G2, 30 (G3 and 60 (G4 days after infiltration. The area and the largest and smallest diameters of the nodules formed by infiltration were evaluated at the site of infiltration and histological examination was performed. The mean granuloma area was similar in all groups. Histopathological examination showed that the material remained isolated from surrounding tissues by a pseudocapsule that became denser throughout the experiment. A host reaction started with young fibroblastic tissue that evolved to dense tissue until cartilaginous tissue was formed in G4, progressively advancing towards the center of the granuloma from G1 to G4. Non-absorbable microgranular hydroxyapatite is an inert material that was well tolerated by the animals studied, with maintenance of the infiltrated volume, and may perhaps be useful to fill anophthalmic cavities.

Evaluating the Infiltration Performance of Eight Dutch Permeable Pavements Using a New Full-Scale Infiltration Testing Method

Directory of Open Access Journals (Sweden)

Floris Boogaard

2014-07-01

Full Text Available Permeable pavements are a type of sustainable urban drainage system (SUDS technique that are used around the world to infiltrate and treat urban stormwater runoff and to minimize runoff volumes. Urban stormwater runoff contains significant concentrations of suspended sediments that can cause clogging and reduce the infiltration capacity and effectiveness of permeable pavements. It is important for stormwater managers to be able to determine when the level of clogging has reached an unacceptable level, so that they can schedule maintenance or replacement activities as required. Newly-installed permeable pavements in the Netherlands must demonstrate a minimum infiltration capacity of 194 mm/h (540 l/s/ha. Other commonly used permeable pavement guidelines in the Netherlands recommend that maintenance is undertaken on permeable pavements when the infiltration falls below 0.50 m/d (20.8 mm/h. This study used a newly-developed, full-scale infiltration test procedure to evaluate the infiltration performance of eight permeable pavements in five municipalities that had been in service for over seven years in the Netherlands. The determined infiltration capacities vary between 29 and 342 mm/h. Two of the eight pavements show an infiltration capacity higher than 194 mm/h, and all infiltration capacities are higher than 20.8 mm/h. According to the guidelines, this suggests that none of the pavements tested in this study would require immediate maintenance.

The Geology of the Kivetty area

International Nuclear Information System (INIS)

Anttila, P.; Paulamaeki, S.; Lindberg, A.; Paananen, M.; Koistinen, T.; Front, K.; Pitkaenen, P.

1992-05-01

Teollisuuden Voima Oy (TVO) is preparing for the final disposal of spent nuclear fuel from the Olkiluoto nuclear power plant (TVO-I and TVO-II) deep in the Finnish bedrock. Kivetty in Konginkangas was one of the five areas selected in 1987 for preliminary site investigations for this purpose. The Kivetty area in Central Finland is located in a Svecokarelian granitoid environment consisting of a complex of synorogenic granitoids 1900 - 1860 million years in age. The bedrock consists almost entirely of plutonic rocks, i.e. gabbro, porphyritic granodiorite and granite, eguigranular granodiorite and granite, listed in order of age. The majority of the rock types are porphyritic in character, and supracrustal rocks such as quartz-feldspar schist and gneiss are found occasionally in small xenoliths

Digital compilation bedrock geologic map of the Warren quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-4A Walsh, GJ, Haydock, S, Prewitt, J, Kraus, J, Lapp, E, O'Loughlin, S, and Stanley, RS, 1995, Digital compilation bedrock geologic map of the...

Seabed geodiversity in a glaciated shelf area, the Baltic Sea

Science.gov (United States)

Kaskela, Anu Marii; Kotilainen, Aarno Tapio

2017-10-01

Geodiversity describes the heterogeneity of the physical terrain. We have performed basin-wide geodiversity analysis on a glaciated epicontinental seabed to assess geodiversity measures and patterns, locate areas with high geodiversity, and draw conclusions on contributing processes. Geodiversity quantification is a rather new topic and is mainly practiced in land areas. We applied geodiversity methods developed for terrestrial studies to a seabed environment. Three geodiversity parameters, including the richness, patchiness, and geodiversity index, of the Baltic Sea were assessed in a GIS environment based on broad-scale datasets on seabed substrates, structures, and bedrock. A set of environmental and geological variables, which were considered to reflect geological processes under seabed conditions, were compared with the geodiversity to identify some of its drivers. We observed differences in the geodiversity levels of the Baltic subbasins, which are mainly due to basement type/bedrock, roughness, shore density, and glacier-derived processes. The geodiversity of the Baltic Sea generally increases from South to North and from open-sea to high-shore density areas (archipelagos). Crystalline bedrock areas provide more diverse seabed environments than sedimentary rock areas. The analysis helps to inform scientists, marine spatial planners, and managers about abiotic conservation values, the dynamics of the seabed environment, and potential areas with elevated biodiversity.

Water infiltration in soil at catchment scale: consequences for cold-climate regions

OpenAIRE

Stolte, J.; French, H.K.; Ritsema, C.J.

2008-01-01

Soil erosion is a global problem because of its environmental consequences, including sedimentation and pollution in many areas of the world. An estimated 400 million hectares of land have been abandoned due to soil erosion over the past 50 years. The main biophysical factor influencing the quantity of overland flow is the infiltration rate. Infiltration during a runoff-generating rainfall event is regulated by the hydraulic properties of the Critical Zone and the antecedent soil moisture con...

Depth of Intestinal Wall Infiltration and Clinical Presentation of Deep Infiltrating Endometriosis: Evaluation of 553 Consecutive Cases.

Science.gov (United States)

Rossini, Roberto; Lisi, Giorgio; Pesci, Anna; Ceccaroni, Marcello; Zamboni, Giuseppe; Gentile, Irene; Rettore, Lorenzo; Ruffo, Giacomo

2018-02-01

Intestinal involvement in endometriosis was first described by Sampson in 1922. The reported incidence ranges between 3% and 37% in patients diagnosed with endometriosis. In literature, there are few studies that correlate the severity of endometriosis (in terms of intestinal infiltration) and its clinical presentation. The aim of this study was to review the correlation between the severity of symptoms, the depth of intestinal wall infiltration, and lymph node involvement in our tertiary referral center. We retrospectively analyzed 553 patients who had undergone intestinal resection for deep infiltrating endometriosis at our institution (Sacro Cuore Negrar Hospital) between 2004 and 2009. Based on intestinal wall infiltration, we divided patients into three groups (Group A: intestinal infiltration that reaches the muscle layer, Group B: infiltration to the submucosa, and Group C: endometriosis reaches the mucosa). Symptoms, intestinal stenosis, and positive lymph nodes were compared in the three groups with the chi-square test. No statistical correlation was found between symptoms and the intestinal wall infiltrations. The three groups were also compared on the basis of positive visceral lymph nodes and we did find a statistical difference (P = .05) in the lymph node count in the two main groups. There seems to be no statistically significant difference in symptoms between patients with different degrees of infiltration. Although visceral lymph node involvement has been occasionally described in literature, we found that it is related to submucosal infiltration.

Application of Seismic Observation Data in Borehole for the Development of Attenuation Equation of Response Spectra on Bedrock

International Nuclear Information System (INIS)

Si, Hongjun

2014-01-01

Ground motion data on seismic bedrock is important, but it is very difficult to obtain such data directly. The data from KiK-net and JNES/SODB is valuable and very useful in developing the attenuation relationship of response spectra on seismic bedrock. NIED has approximately 200 observation points on seismic bedrock with S-wave velocity of more than 2000 m/s in Japan. Using data from observation at these points, a Ground Motion Prediction Equation (GMPE) is under development. (author)

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA.

Science.gov (United States)

Yang, Qiang; Culbertson, Charles W; Nielsen, Martha G; Schalk, Charles W; Johnson, Carole D; Marvinney, Robert G; Stute, Martin; Zheng, Yan

2015-02-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 μg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70-100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93-99%) in particulates (>0.45 μm). These particulates and those settled after a 16-day batch experiment contain 560-13,000 mg/kg of As and 14-35% weight/weight of Fe. As/Fe ratios (2.5-20 mmol/mol) and As partitioning ratios (adsorbed/dissolved [As], 20,000-100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ(18)O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes the oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater. Copyright © 2014 Elsevier B.V. All rights reserved.

Digital Bedrock Compilation: A Geodatabase Covering Forest Service Lands in California

Science.gov (United States)

Elder, D.; de La Fuente, J. A.; Reichert, M.

2010-12-01

This digital database contains bedrock geologic mapping for Forest Service lands within California. This compilation began in 2004 and the first version was completed in 2005. Second publication of this geodatabase was completed in 2010 and filled major gaps in the southern Sierra Nevada and Modoc/Medicine Lake/Warner Mountains areas. This digital map database was compiled from previously published and unpublished geologic mapping, with source mapping and review from California Geological Survey, the U.S. Geological Survey and others. Much of the source data was itself compilation mapping. This geodatabase is huge, containing ~107,000 polygons and ~ 280,000 arcs. Mapping was compiled from more than one thousand individual sources and covers over 41,000,000 acres (~166,000 km2). It was compiled from source maps at various scales - from ~ 1:4,000 to 1:250,000 and represents the best available geologic mapping at largest scale possible. An estimated 70-80% of the source information was digitized from geologic mapping at 1:62,500 scale or better. Forest Service ACT2 Enterprise Team compiled the bedrock mapping and developed a geodatabase to store this information. This geodatabase supports feature classes for polygons (e.g, map units), lines (e.g., contacts, boundaries, faults and structural lines) and points (e.g., orientation data, structural symbology). Lookup tables provide detailed information for feature class items. Lookup/type tables contain legal values and hierarchical groupings for geologic ages and lithologies. Type tables link coded values with descriptions for line and point attributes, such as line type, line location and point type. This digital mapping is at the core of many quantitative analyses and derivative map products. Queries of the database are used to produce maps and to quantify rock types of interest. These include the following: (1) ultramafic rocks - where hazards from naturally occurring asbestos are high, (2) granitic rocks - increased

Measurement of infiltration rates in urban sewer systems by use of oxygen isotopes.

Science.gov (United States)

De Bénédittis, J; Bertrand-Krajewski, J L

2005-01-01

The paper presents the principle of a method to measure infiltration rates in sewer systems based on the use of oxygen isotopes and its application in Lyon (France). In the urban area of Lyon, significant differences in delta 18O that can reach 3 per thousand are observed between the oxygen isotopic compositions of groundwater originating from Rhone, Saone and from their associated alluvial aquifers. Drinking water supplying Lyon results mainly from pumping in the Rhone alluvial aquifer. Therefore, in some areas, the difference of isotopic composition between wastewater resulting from the consumption of drinking water and local groundwater can be used to measure infiltration in sewer systems. The application in the catchment of Ecully shows that the infiltration flow rate presents strong fluctuations at an hourly scale: it varies between 15 and 40 m3/h. This variability could be explained by non-constant discharges of pumping and by variations of the water level in the sewer.

[Soil infiltration capacity under different vegetations in southern Ningxia Loess hilly region].

Science.gov (United States)

Yang, Yong-Hui; Zhao, Shi-Wei; Lei, Ting-Wu; Liu, Han

2008-05-01

A new apparatus for measuring the run off-on-out under simulated rainfall conditions was used to study the soil infiltration capacity under different rainfall intensities and vegetations in loess hilly region of southern Ningxia, with the relationships between soil water-stable aggregate content and soil stable infiltration rate under different vegetations analyzed. The results showed that the regression equations between rainfall duration and soil infiltration rate under different vegetations all followed y = a + be(-cx), with R2 ranged from 0.9678 to 0.9969. With the increase of rainfall intensity, the soil stable infiltration rate on slope cropland decreased, while that on Medicago lupulina land, natural grassland, and Caragana korshinskii land increased. Under the rainfall intensity of 20 mm h(-1), the rainfall infiltration translation rate (RITR) was decreased in the order of M. lupulina land > slope cropland > natural grassland > C. korshinskii land; while under the rainfall intensity of 40 mm h(-1) and 56 mm h(-1), the RITR was in the sequence of M. lupulina land > natural grassland > slope cropland > C. korshinskii land, and decreased with increasing rainfall intensity. After the reversion of cropland to grassland and forest land, and with the increase of re-vegetation, the amount of >0.25 mm soil aggregates increased, and soil infiltration capacity improved. The revegetation in study area effectively improved soil structure and soil infiltration capacity, and enhanced the utilization potential of rainfall on slope.

Spatial variability in mycorrhizal hyphae and nutrient and water availability in a soil-weathered bedrock profile

Science.gov (United States)

L.M. Egerton-Warburton; R.C. Graham; K.R. Hubbert

2003-01-01

We documented the spatial distribution, abundance and molecular diversity of mycorrhizal hyphae and physical and chemical properties of soil-weathered bedrock in a chaparral community that experiences seasonal drought. Because plants in this community were known to rely on bedrock-stored water during the summer, the data were used to evaluate the potential role of...

Measuring the relative extent of pulmonary infiltrates by hierarchical classification of patient-specific image features

Science.gov (United States)

Tsevas, S.; Iakovidis, D. K.

2011-11-01

Pulmonary infiltrates are common radiological findings indicating the filling of airspaces with fluid, inflammatory exudates, or cells. They are most common in cases of pneumonia, acute respiratory syndrome, atelectasis, pulmonary oedema and haemorrhage, whereas their extent is usually correlated with the extent or the severity of the underlying disease. In this paper we propose a novel pattern recognition framework for the measurement of the extent of pulmonary infiltrates in routine chest radiographs. The proposed framework follows a hierarchical approach to the assessment of image content. It includes the following: (a) sampling of the lung fields; (b) extraction of patient-specific grey-level histogram signatures from each sample; (c) classification of the extracted signatures into classes representing normal lung parenchyma and pulmonary infiltrates; (d) the samples for which the probability of belonging to one of the two classes does not reach an acceptable level are rejected and classified according to their textural content; (e) merging of the classification results of the two classification stages. The proposed framework has been evaluated on real radiographic images with pulmonary infiltrates caused by bacterial infections. The results show that accurate measurements of the infiltration areas can be obtained with respect to each lung field area. The average measurement error rate on the considered dataset reached 9.7% ± 1.0%.

Infiltration characteristics of non-aqueous phase liquids in undisturbed loessal soil cores.

Science.gov (United States)

Wang, Yunqiang; Shao, Ming'an

2009-01-01

The widespread contamination of soils and aquifers by non-aqueous phase liquids (NAPL), such as crude oil, poses serious environmental and health hazards globally. Understanding the infiltration characteristics of NAPL in soil is crucial in mitigating or remediating soil contamination. The infiltration characteristics of crude and diesel oils into undisturbed loessal soil cores, collected in polymethyl methacrylate cylindrical columns, were investigated under a constant fluid head (3 cm) of either crude oil or diesel oil. The infiltration rate of both crude and diesel oils decreased exponentially as wetting depth increased with time. Soil core size and bulk density both had significant effects on NAPL infiltration through the undisturbed soil cores; a smaller core size or a greater bulk density could reduce oil penetration to depth. Compacting soil in areas susceptible to oil spills may be an effective stratage to reduce contamination. The infiltration of NAPL into soil cores was spatially anisotropic and heterogeneous, thus recording the data at four points on the soil core is a good stratage to improve the accuracy of experimental results. Our results revealed that crude and diesel oils, rather than their components, have a practical value for remediation of contaminated loessal soils.

Eosinophilic infiltration in Korea: idiopathic?

Energy Technology Data Exchange (ETDEWEB)

Lim, Jae Hoon; Lee, Kyung Soo [Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of)

2006-03-15

Eosinophilia is defined as the presence of more than 500 eosinophils/{mu}L in the peripheral blood, and may be accompanied by eosinophil infiltration in tissues. Focal eosinophilic infiltration in the lungs and liver is relatively common and is often associated with a parasitic infection, drug hypersensitivity, allergic diseases, collagen vascular diseased, and internal malignancies such as Hodgkin's disease, as well as cancer of the lung, stomach, pancreas or ovary. An eosinophilic abscess refers to a lesion of massive eosinophil infiltration and associated destroyed tissue, and an eosinophilic granuloma refers to a lesion consisting of central necrosis and mixed inflammatory cell infiltrates with numerous eosinophils, a number of neutrophils and lymphocytes, and a palisade of epithelioid histiocytes and/or giant cells.

Eosinophilic infiltration in Korea: idiopathic?

International Nuclear Information System (INIS)

Lim, Jae Hoon; Lee, Kyung Soo

2006-01-01

Eosinophilia is defined as the presence of more than 500 eosinophils/μL in the peripheral blood, and may be accompanied by eosinophil infiltration in tissues. Focal eosinophilic infiltration in the lungs and liver is relatively common and is often associated with a parasitic infection, drug hypersensitivity, allergic diseases, collagen vascular diseased, and internal malignancies such as Hodgkin's disease, as well as cancer of the lung, stomach, pancreas or ovary. An eosinophilic abscess refers to a lesion of massive eosinophil infiltration and associated destroyed tissue, and an eosinophilic granuloma refers to a lesion consisting of central necrosis and mixed inflammatory cell infiltrates with numerous eosinophils, a number of neutrophils and lymphocytes, and a palisade of epithelioid histiocytes and/or giant cells

Digital and preliminary bedrock geologic map of the Wallingford quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-335A Burton, WC, and Ratcliffe, NM, 2000, Digital and preliminary bedrock geologic map of the Wallingford quadrangle, Vermont: USGS Open-File...

Modeling snowmelt infiltration in seasonally frozen ground

Science.gov (United States)

Budhathoki, S.; Ireson, A. M.

2017-12-01

In cold regions, freezing and thawing of the soil govern soil hydraulic properties that shape the surface and subsurface hydrological processes. The partitioning of snowmelt into infiltration and runoff has also important implications for integrated water resource management and flood risk. However, there is an inadequate representation of the snowmelt infiltration into frozen soils in most land-surface and hydrological models, creating the need for improved models and methods. Here we apply, the Frozen Soil Infiltration Model, FroSIn, which is a novel algorithm for infiltration in frozen soils that can be implemented in physically based models of coupled flow and heat transport. In this study, we apply the model in a simple configuration to reproduce observations from field sites in the Canadian prairies, specifically St Denis and Brightwater Creek in Saskatchewan, Canada. We demonstrate the limitations of conventional approaches to simulate infiltration, which systematically over-predict runoff and under predict infiltration. The findings show that FroSIn enables models to predict more reasonable infiltration volumes in frozen soils, and also represent how infiltration-runoff partitioning is impacted by antecedent soil moisture.

Plant response to nutrient availability across variable bedrock geologies

Science.gov (United States)

Castle, S.C.; Neff, J.C.

2009-01-01

We investigated the role of rock-derived mineral nutrient availability on the nutrient dynamics of overlying forest communities (Populus tremuloides and Picea engelmanni-Abies lasiocarpa v. arizonica) across three parent materials (andesite, limestone, and sandstone) in the southern Rocky Mountains of Colorado. Broad geochemical differences were observed between bedrock materials; however, bulk soil chemistries were remarkably similar between the three different sites. In contrast, soil nutrient pools were considerably different, particularly for P, Ca, and Mg concentrations. Despite variations in nutrient stocks and nutrient availability in soils, we observed relatively inflexible foliar concentrations and foliar stoichiometries for both deciduous and coniferous species. Foliar nutrient resorption (P and K) in the deciduous species followed patterns of nutrient content across substrate types, with higher resorption corresponding to lower bedrock concentrations. Work presented here indicates a complex plant response to available soil nutrients, wherein plant nutrient use compensates for variations in supply gradients and results in the maintenance of a narrow range in foliar stoichiometry. ?? 2008 Springer Science+Business Media, LLC.

In-situ infiltration performance of different permeable pavements in a employee used parking lot--A four-year study.

Science.gov (United States)

Kumar, Kuldip; Kozak, Joseph; Hundal, Lakhwinder; Cox, Albert; Zhang, Heng; Granato, Thomas

2016-02-01

Permeable pavements are being adopted as a green solution in many parts of the world to manage urban stormwater quantity and quality. This paper reports on the measured in-situ infiltration performance over a four-year period since construction and use of three permeable parking sections (permeable pavers, permeable concrete and permeable asphalt) of an employee car parking lot. There was only a marginal decline in infiltration rates of all three pavements after one year of use. However, between years two to four, the infiltration rates declined significantly due to clogging of pores either by dry deposition of particles and/or shear stress of vehicles driving and degrading the permeable surfaces; during the last two years, a greater decline was also observed in driving areas of the parking lots compared to parking slots, where minimal wear and tear are expected. Maintenance strategies were employed to reclaim some of the lost infiltration rate of the permeable pavements to limited success. Despite this decline, the infiltration rates were still four to five times higher than average rainstorm intensity in the region. Thus, these permeable pavement parking lots may have significant ecological importance due to their ability to infiltrate rainwater quickly, reduce the runoff in the catchment area, and also dampen runoff peak flows that could otherwise enter the collection system for treatment in a combined sewer area. Copyright © 2015 Elsevier Ltd. All rights reserved.

Application of spreadsheet to estimate infiltration parameters

Directory of Open Access Journals (Sweden)

Mohammad Zakwan

2016-09-01

Full Text Available Infiltration is the process of flow of water into the ground through the soil surface. Soil water although contributes a negligible fraction of total water present on earth surface, but is of utmost importance for plant life. Estimation of infiltration rates is of paramount importance for estimation of effective rainfall, groundwater recharge, and designing of irrigation systems. Numerous infiltration models are in use for estimation of infiltration rates. The conventional graphical approach for estimation of infiltration parameters often fails to estimate the infiltration parameters precisely. The generalised reduced gradient (GRG solver is reported to be a powerful tool for estimating parameters of nonlinear equations and it has, therefore, been implemented to estimate the infiltration parameters in the present paper. Field data of infiltration rate available in literature for sandy loam soils of Umuahia, Nigeria were used to evaluate the performance of GRG solver. A comparative study of graphical method and GRG solver shows that the performance of GRG solver is better than that of conventional graphical method for estimation of infiltration rates. Further, the performance of Kostiakov model has been found to be better than the Horton and Philip's model in most of the cases based on both the approaches of parameter estimation.

Digital bedrock mapping at the Geological Survey of Norway: BGS SIGMA tool and in-house database structure

Science.gov (United States)

Gasser, Deta; Viola, Giulio; Bingen, Bernard

2016-04-01

Since 2010, the Geological Survey of Norway has been implementing and continuously developing a digital workflow for geological bedrock mapping in Norway, from fieldwork to final product. Our workflow is based on the ESRI ArcGIS platform, and we use rugged Windows computers in the field. Three different hardware solutions have been tested over the past 5 years (2010-2015). (1) Panasonic Toughbook CE-19 (2.3 kg), (2) Panasonic Toughbook CF H2 Field (1.6 kg) and (3) Motion MC F5t tablet (1.5 kg). For collection of point observations in the field we mainly use the SIGMA Mobile application in ESRI ArcGIS developed by the British Geological Survey, which allows the mappers to store georeferenced comments, structural measurements, sample information, photographs, sketches, log information etc. in a Microsoft Access database. The application is freely downloadable from the BGS websites. For line- and polygon work we use our in-house database, which is currently under revision. Our line database consists of three feature classes: (1) bedrock boundaries, (2) bedrock lineaments, and (3) bedrock lines, with each feature class having up to 24 different attribute fields. Our polygon database consists of one feature class with 38 attribute fields enabling to store various information concerning lithology, stratigraphic order, age, metamorphic grade and tectonic subdivision. The polygon and line databases are coupled via topology in ESRI ArcGIS, which allows us to edit them simultaneously. This approach has been applied in two large-scale 1:50 000 bedrock mapping projects, one in the Kongsberg domain of the Sveconorwegian orogen, and the other in the greater Trondheim area (Orkanger) in the Caledonian belt. The mapping projects combined collection of high-resolution geophysical data, digital acquisition of field data, and collection of geochronological, geochemical and petrological data. During the Kongsberg project, some 25000 field observation points were collected by eight

Vadose Zone Infiltration Rates from Sr isotope Measurements

Science.gov (United States)

Maher, K.; Maher, K.; DePaolo, D. J.; DePaolo, D. J.; Conrad, M.

2001-12-01

Predicting infiltration rates and recharge through the vadose zone in arid regions is difficult and hence developing methods for the measurement of infiltration rates is important. We have been investigating the use of Sr isotope measurements for determining infiltration at the 200 Area plateau on the Hanford reservation in central Washington. In this context, infiltration affects the transport of contaminants to the water table as well as recharge of the groundwater system. Using Sr isotopes for this purpose requires drill core and water samples from the vadose zone, although leaches of the cores can substitute for water samples. Complementary information, including some constraints on regional recharge, can also be obtained using water samples from groundwater monitoring wells. The VZ method is based on the fact that the Sr isotope ratio of soil water just below the surface is often set by dissolution of aeolian material including carbonate, and this ratio is different from the average value in the deeper underlying vadose zone rock matrix. As water infiltrates, the Sr isotopic composition of the water changes toward the rock values as a result of Sr released from the rocks by weathering reactions. The rate of change with depth of the Sr isotope ratio of the vadose zone water is a function ultimately of q/R; the ratio of the infiltration flux (q) to the bulk rock weathering rate (R). Where it is possible to evaluate R, q can be estimated. As data accumulate it may be possible to improve the calibration of the method. At Hanford the vadose zone rock material is mostly unconsolidated sand, silt, and gravel of broadly granitic composition, which constitute the Hanford and Ringold formations. Annual precipitation is about 160 mm/yr. Drilling and coring of a ca. 70m hole to the water table in 1999 as part of the Hanford groundwater monitoring program, in a relatively undisturbed area of the site, allowed us to generate a unique Sr isotope data set. The Sr isotope

Digital and preliminary bedrock geologic map of the Chittenden quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG97-854A Ratcliffe, NM, 1997,�Digital and preliminary bedrock geologic map of the Chittenden quadrangle, Vermont: USGS Open-File Report 97-854, 1...

Infiltration properties of soils during extreme precipitation in the catchment area of Litavka

OpenAIRE

Hubinger, Lukáš

2013-01-01

The aim of this work is the measurement of some selected soil parameters and hydraulic conductivity. By the evalution of these data is determined the resolution of selected soil properties on the base of these characteristics and also predisposition to surface runoff and erosion washes away during a certain rain intensity. This paper contain the comparison of the soil infiltration capacity at selected values of soil water saturation. From the rainfall data is determined the size, frequency, d...

Initial yield to depth relation for water wells drilled into crystalline bedrock - Pinardville quadrangle, New Hampshire

Science.gov (United States)

Drew, L.J.; Schuenemeyer, J.H.; Amstrong, T.R.; Sutphin, D.M.

2001-01-01

A model is proposed to explain the statistical relations between the mean initial water well yields from eight time increments from 1984 to 1998 for wells drilled into the crystalline bedrock aquifer system in the Pinardville area of southern New Hampshire and the type of bedrock, mean well depth, and mean well elevation. Statistical analyses show that the mean total yield of drilling increments is positively correlated with mean total well depth and mean well elevation. In addition, the mean total well yield varies with rock type from a minimum of 46.9 L/min (12.4 gpm) in the Damon Pond granite to a maximum of 74.5 L/min (19.7 gpm) in the Permian pegmatite and granite unit. Across the eight drilling increments that comprise 211 wells each, the percentages of very low-yield wells (1.9 L/min [0.5 gpm] or less) and high-yield wells (151.4 L/min [40 gpm] or more) increased, and those of intermediate-yield wells decreased. As housing development progressed during the 1984 to 1998 interval, the mean depth of the wells and their elevations increased, and the mix of percentages of the bedrock types drilled changed markedly. The proposed model uses a feed-forward mechanism to explain the interaction between the increasing mean elevation, mean well depth, and percentages of very low-yielding wells and the mean well yield. The increasing percentages of very low-yielding wells through time and the economics of the housing market may control the system that forces the mean well depths, percentages of high-yield wells, and mean well yields to increase. The reason for the increasing percentages of very low-yield wells is uncertain, but the explanation is believed to involve the complex structural geology and tectonic history of the Pinardville quadrangle.

Radioelement (U,Th,Rn) concentrations in Norwegian bedrock groundwaters

International Nuclear Information System (INIS)

Banks, D.; Roeyset, O.; Strand, T.; Skarphagen, H.

1993-12-01

Samples of groundwater from bedrock boreholes in three Norwegian geological provinces have been analysed for content of 222 Rn, U and Th. Median values of 290 Bq/l, 7.6 μg/l and 0.02 μg/l were obtained for Rn, U and Th, respectively, while maximum values were 8500 Bq/l, 170 μg/l and 2.2 μg/l. Commonly suggested drinking water limits range from 8 to 1000 Bq/l for radon and 14 to 160 μg/l for uranium. Radioelement content was closely related to lithology, the lowest concentrations being derived from the largely Caledonian rocks of the Troendelag area, and the highest from the Precambrian Iddefjord Granite of South East Norway where median values of 2500 Bq/l, 15 μg/l and 0.38 μg/l, respectively, were obtained. The Iddefjord Granite is not believed to be unique in Norway yielding high dissolved radionuclide contents in groundwaters, and several other granitic aquifers warrant further investigation in this respect. 63 refs., 13 figs., 8 tabs

Experimental Plan: 300 Area Treatability Test: In Situ Treatment of the Vadose Zone and Smear Zone Uranium Contamination by Polyphosphate Infiltration

International Nuclear Information System (INIS)

Wellman, Dawn M.; Pierce, Eric M.; Oostrom, Mart; Fruchter, Jonathan S.

2007-01-01

The overall objectives of the treatability test is to evaluate and optimize polyphosphate remediation technology for infiltration either from ground surface, or some depth of excavation, providing direct stabilization of uranium within the deep vadose and capillary fringe above the 300 Area aquifer. Expected result from this experimental plan is a data package that includes: (1) quantification of the retardation of polyphosphate, (2) the rate of degradation and the retardation of degradation products as a function of water content, (3) an understanding of the mechanism of autunite formation via the reaction of solid phase calcite-bound uranium and aqueous polyphosphate remediation technology, (4) an understanding of the transformation mechanism, identity of secondary phases, and the kinetics of the reaction between uranyl-carbonate and silicate minerals with the polyphosphate remedy under solubility-limiting conditions, (5) quantification of the extent and rate of uranium released and immobilized based on the infiltration rate of the polyphosphate remedy and the effect of and periodic wet-dry cycling on the efficacy of polyphosphate remediation for uranium in the vadose zone and capillary fringe, and (6) quantification of reliable equilibrium solubility values for autunite under hydraulically unsaturated conditions allowing accurate prediction of the long-term stability of autunite. Moreover, results of intermediate scale testing will quantify the transport of polyphosphate and degradation products, and yield degradation rates, at a scale that is bridging the gap between the small-scale UFA studies and the field scale. These results will be used to test and verify a site-specific, variable saturation, reactive transport model and to aid in the design of a pilot-scale field test of this technology. In particular, the infiltration approach and monitoring strategy of the pilot test would be primarily based on results from intermediate-scale testing. Results from this

Bedrock Canyons Carved by the Largest Known Floods on Earth and Mars

Science.gov (United States)

Lamb, M. P.; Lapôtre, M. G. A.; Larsen, I. J.; Williams, R. M. E.

2017-12-01

The surface of Earth is a dynamic and permeable interface where the rocky crust is sculpted by ice, wind and water resulting in spectacular mountain ranges, vast depositional basins and environments that support life. These landforms and deposits contain a rich, yet incomplete, record of Earth history that we are just beginning to understand. Some of the most dramatic landforms are the huge bedrock canyons carved by catastrophic floods. On Mars, similar bedrock canyons, known as Outflow Channels, are the most important indicators of large volumes of surface water in the past. Despite their importance and now decades of observations of canyon morphology, we lack a basic understanding of how the canyons formed, which limits our ability to reconstruct flood discharge, duration and water volume. In this presentation I will summarize recent work - using mechanistic numerical models and field observations - that suggests that bedrock canyons carved by megafloods rapidly evolve to a size and shape such that boundary shear stresses just exceed that required to entrain fractured blocks of rock. The threshold shear stress constraint allows for quantitative reconstruction of the largest known floods on Earth and Mars, and implies far smaller discharges than previous methods that assume flood waters fully filled the canyons to high water marks.

Infiltrating/sealing proximal caries lesions

DEFF Research Database (Denmark)

Martignon, S; Ekstrand, K R; Gomez, J

2012-01-01

This randomized split-mouth controlled clinical trial aimed at assessing the therapeutic effects of infiltration vs. sealing for controlling caries progression on proximal surfaces. Out of 90 adult students/patients assessed at university clinics and agreeing to participate, 39, each with 3...... differences in lesion progression between infiltration and placebo (P = 0.0012) and between sealing and placebo (P = 0.0269). The study showed that infiltration and sealing are significantly better than placebo treatment for controlling caries progression on proximal lesions. No significant difference...

Research on the infiltration processes of lawn soils of the Babao River in the Qilian Mountain.

Science.gov (United States)

Li, GuangWen; Feng, Qi; Zhang, FuPing; Cheng, AiFang

2014-01-01

Using a Guelph Permeameter, the soil water infiltration processes were analyzed in the Babao River of the Qilian Mountain in China. The results showed that the average soil initial infiltration and the steady infiltration rates in the upstream reaches of the Babao River are 1.93 and 0.99 cm/min, whereas those of the middle area are 0.48 cm/min and 0.21 cm/min, respectively. The infiltration processes can be divided into three stages: the rapidly changing stage (0-10 min), the slowly changing stage (10-30 min) and the stabilization stage (after 30 min). We used field data collected from lawn soils and evaluated the performances of the infiltration models of Philip, Kostiakov and Horton with the sum of squared error, the root mean square error, the coefficient of determination, the mean error, the model efficiency and Willmott's index of agreement. The results indicated that the Kostiakov model was most suitable for studying the infiltration process in the alpine lawn soils.

Artificial Recharge – Measurement of Soil Infiltration in Rožnov Pod Radhoštěm

Directory of Open Access Journals (Sweden)

Chromíková Jitka

2017-12-01

Full Text Available The purpose of this study is to evaluate the potential for infiltration in a study area – Rožnov pod Radhoštěm, the Czech Republic. The results are important for the future design of an artificial recharge structure as a method to store water underground in times of water surplus. A total of six measurements of infiltration were made using a double ring infiltrometer on selected prospective sites for the future application of artificial recharge. The results of infiltration tests were analysed based on the Philip’s model. The steady soil infiltration rates ranged from 28 cm∙h−1 to 70.38 cm∙h−1and the cumulative soil infiltration ranged from 58 cm to 68 cm.

The effects of fuel reduction treatments on runoff, infiltration and erosion in two shrubland areas in the north of Spain.

Science.gov (United States)

Fernández, Cristina; Vega, José A; Fonturbel, Teresa

2012-08-30

The immediate effects of prescribed burning, shrub clearing and shrub mastication on runoff, infiltration and erosion were evaluated in two contrasting shrubland areas in northern Spain. Rainfall simulations (67 mm h(-1) for 30 min) were conducted immediately after fuel reduction treatments in each runoff plot. Compared to shrub mastication and shrub clearing, prescribed burning generated the lowest infiltration rate and highest runoff and erosion rates at both study sites. However, sediment yields measured immediately after treatments were low in all cases, from 0.31 to 2.22 g m(-2) after shrub clearing, 0.40-1.63 g m(-2) after shrub mastication and 2.30-8.11 g m(-2) after prescribed burning. Slope, type of fuel reduction treatment and the depth and cover of the soil organic layer remaining after treatment were the most important variables determining runoff and erosion during the first rainfall event following treatment. In the rainfall simulation plots subjected to prescribed burning, the maximum temperatures reached at the organic layer/mineral soil interface during burning also had a significant effect on soil loss. The findings show that good fuel management prescriptions make fire hazard reduction and soil conservation compatible in cases where the remaining soil cover is about 70%. Copyright © 2012 Elsevier Ltd. All rights reserved.

A case report of an inverted papilloma infiltrating into maxillary sinus

International Nuclear Information System (INIS)

Ji, Yong Hwa; Choi, Bo Ram; Huh, Kyung Hoe; Lee, Sam Sun; An, Chang Hyeon

2009-01-01

The present study reports a case of inverted papilloma of the nasal cavity and infiltrating into the maxillary sinus. Inverted papilloma is an uncommon and locally aggressive benign tumor of the sinonasal region. The patient, 51-year-old male, presented with unilateral nasal obstruction and periodic swelling on the palate without pain. Enhanced CT scan revealed a heterogeneously enhancing solid mass in the nasal cavity and infiltrating into the right maxillary sinus, as well as an incidental, secondarily infected residual cyst in the periapical area of the right maxillary canine. The sinonasal mass was revealed as an inverted papilloma on histopathologic examination.

A case report of an inverted papilloma infiltrating into maxillary sinus

Energy Technology Data Exchange (ETDEWEB)

Ji, Yong Hwa; Choi, Bo Ram; Huh, Kyung Hoe; Lee, Sam Sun [School of Dentistry, Seoul National University, Seoul (Korea, Republic of); An, Chang Hyeon [Department of Oral and Maxillofacial Radiology, School of Dentistry, Kyungpook National University, Daegu (Korea, Republic of)

2009-06-15

The present study reports a case of inverted papilloma of the nasal cavity and infiltrating into the maxillary sinus. Inverted papilloma is an uncommon and locally aggressive benign tumor of the sinonasal region. The patient, 51-year-old male, presented with unilateral nasal obstruction and periodic swelling on the palate without pain. Enhanced CT scan revealed a heterogeneously enhancing solid mass in the nasal cavity and infiltrating into the right maxillary sinus, as well as an incidental, secondarily infected residual cyst in the periapical area of the right maxillary canine. The sinonasal mass was revealed as an inverted papilloma on histopathologic examination.

Digital and preliminary bedrock geologic map of the Rutland quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-121A Ratcliffe, N.M., 1998,�Digital and preliminary bedrock geologic map of the Rutland quadrangle, Vermont: USGS Open-File Report 98-121-A, 1...

Digital compilation bedrock geologic map of the Mt. Ellen quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-6A Stanley, RS, Walsh, G, Tauvers, PR, DiPietro, JA, and DelloRusso, V, 1995,�Digital compilation bedrock geologic map of the Mt. Ellen...

Cross-hole fracture connectivity assessed using hydraulic responses during liner installations in crystalline bedrock boreholes

Science.gov (United States)

Persaud, Elisha; Levison, Jana; Pehme, Peeter; Novakowski, Kentner; Parker, Beth

2018-01-01

In order to continually improve the current understanding of flow and transport in crystalline bedrock environments, developing and improving fracture system characterization techniques is an important area of study. The presented research examines the installation of flexible, impermeable FLUTe™ liners as a means for assessing cross-hole fracture connectivity. FLUTe™ liners are used to generate a new style of hydraulic pulse, with pressure response monitored in a nearby network of open boreholes drilled in gneissic rock of the Canadian Shield in eastern Ontario, Canada. Borehole liners were installed in six existing 10-15 cm diameter boreholes located 10-35 m apart and drilled to depths ranging between 25-45 m. Liner installation tests were completed consecutively with the number of observation wells available for each test ranging between one and six. The collected pressure response data have been analyzed to identify significant groundwater flow paths between source and observation boreholes as well as to estimate inter-well transmissivity and storativity using a conventional type-curve analysis. While the applied solution relies on a number of general assumptions, it has been found that reasonable comparison can be made to previously completed pulse interference and pumping tests. Results of this research indicate areas where method refinement is necessary, but, nonetheless, highlight the potential for use in crystalline bedrock environments. This method may provide value to future site characterization efforts given that it is complementary to, and can be used in conjunction with, other currently employed borehole liner applications, such as the removal of cross-connection at contaminated sites and the assessment of discrete fracture distributions when boreholes are sealed, recreating natural hydraulic gradient conditions.

Experimental and modelling studies of infiltration

International Nuclear Information System (INIS)

Giudici, M.

2004-01-01

This presentation describes a study of infiltration in the unsaturated soil with the objective of estimating the recharge to a phreatic aquifer. The study area is at the border of the city of Milan (Northern Italy), which draws water for both domestic and industrial purposes from ground water resources located beneath the urban area. The rate of water pumping from the aquifer system has been varying during the XX century, depending upon the number of inhabitants and the development of industrial activities. This caused variations with time of the depth of the water table below the ground surface and in turn some emergencies: the two most prominent episodes correspond to the middle '70s, when the water table in the city centre was about 30 m below the undisturbed natural conditions, and to the last decade, when the water table has raised at a rate of approximately 1 m/year and caused infiltrations in deep constructions (garages and building foundations, the underground railways, etc.). We have developed four ground water flow models at different scales, which share some characteristics: they are based on quasi-3D approximation (horizontal flow in the aquifers and vertical flow in the aquitards), conservative finite-differences schemes for regular grid with square cells in the horizontal plane and are implemented with proprietary computer codes. Among the problems that were studied for the development of these models, I recall some numerical problems, related to the behaviour of the phreatic aquifer under conditions of strong exploitation. Model calibration and validation for ModMil has been performed with a two-stage process, i.e., using some of the available data for model calibration and the remaining data for model validation. The application of geophysical exploration techniques, in particular seismic and geo-electrical prospecting, has been very useful to complete the data and information on the hydro-geological structure obtained from stratigraphic logs

Assessment on inflow and infiltration in sewerage systems of Kuantan, Pahang.

Science.gov (United States)

Yap, Hiew Thong; Ngien, Su Kong

2017-12-01

Inflow and infiltration are important aspects of sewerage systems that need to be considered during the design stage and constantly monitored once the sewerage system is in operation. The aim of this research is to analyse the relationship of rainfall as well as inflow infiltration with sewage flow patterns through data collected from fieldwork. Three sewer pipelines were selected at the residential areas of Taman Lepar Hilir Saujana, Bandar Putra and Kota Sas for data collection. Sewage flow data were collected in terms of flowrate, velocity and depth of flow using flowmeters with ultrasonic sensors that utilize the continuous Doppler effect in the sewer pipelines, while rainfall intensity data were collected using rain gauges installed at the study locations. Based on the result, the average infiltration rates of Q peak and Q ave for the locations were 17% and 21%, which exceeded the respective values of 5% and 10% stated in Hammer and Hammer. The flowrate of wastewater in the sewer pipelines was found to be directly proportional to rainfall. These findings indicate that the sewer pipelines in the study areas may have been affected by capacity reduction, whereas the sewerage treatment plants receiving the wastewater influent may have been overloaded.

Infiltration performance of engineered surfaces commonly used for distributed stormwater management.

Science.gov (United States)

Valinski, N A; Chandler, D G

2015-09-01

Engineered porous media are commonly used in low impact development (LID) structures to mitigate excess stormwater in urban environments. Differences in infiltrability of these LID systems arise from the wide variety of materials used to create porous surfaces and subsequent maintenance, debris loading, and physical damage. In this study, the infiltration capacity of six common materials was tested by multiple replicate experiments with automated mini-disk infiltrometers. The tested materials included porous asphalt, porous concrete, porous brick pavers, flexible porous pavement, engineered soils, and native soils. Porous asphalt, large porous brick pavers, and curb cutout rain gardens showed the greatest infiltration rates. Most engineered porous pavements and soils performed better than the native silt loam soils. Infiltration performance was found to be related more to site design and environmental factors than material choice. Sediment trap zones in both pavements and engineered soil rain gardens were found to be beneficial to the whole site performance. Winter chloride application had a large negative impact on poured in place concrete, making it a poor choice for heavily salted areas. Copyright © 2015 Elsevier Ltd. All rights reserved.

Digital compilation bedrock geologic map of the South Mountain quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-3A Stanley, R.S., DelloRusso, V., Tauvers, P.R., DiPietro, J.A., Taylor, S., and Prahl, C., 1995, Digital compilation bedrock geologic map of...

Infiltration characteristics of non-aqueous phase liquids in undisturbed loessal soil cores

Institute of Scientific and Technical Information of China (English)

WANG Yunqiang; SHAO Ming'an

2009-01-01

The widespread contamination of soils and aquifers by non-aqueous phase liquids (NAPL), such as crude oil, poses serious environmental and health hazards globally. Understanding the infiltration characteristics of NAPL in soil is crucial in mitigating or remediating soil contamination. The infiltration characteristics of crude and diesel oils into undisturbed loessal soil cores, collected in polymethyl methacrylate cylindrical columns, were investigated under a constant fluid head (3 cm) of either crude oil or diesel oil. The infiltration rate of both crude and diesel oils decreased exponentially as wetting depth increased with time. Soil core size and bulk density both had a significant effect on NAPL infiltration through the undisturbed soil cores; a smaller core size or a greater bulk density both reduced oil penetration to depth. Compacting soil in areas susceptible to oil spills may be an effective way to reduce contamination. The infiltration of NAPL into soil cores was spatially anisotropic and heterogeneous, thus recording the data at four points on the soil core is a good way to improve the accuracy of experimental results. Our results provided information about crude and diesel oils, rather than their components, and may have practical value for remediation of contaminated loessal soils.

External and internal resin infiltration of natural proximal subsurface caries lesions: A valuable enhancement of the internal tunnel restoration.

Science.gov (United States)

Kielbassa, Andrej M; Ulrich, Ina; Werth, Vanessa D; Schüller, Christoph; Frank, Wilhelm; Schmidl, Rita

2017-01-01

The aim of this ex-vivo study was to evaluate both the external and the internal penetration ability of a resin infiltrant into natural proximal and macroscopically intact white spot lesions, and to merge this approach with the internal tunnel preparation concept. 20 premolars and 20 molars with proximal subsurface lesions (ICDAS, code 2) and respective radiographic lesion depths extending into the middle third of dentin (D2 lesions) were selected and divided into two groups. Treatment needs were confirmed using digital imaging fiber-optic transillumination and laser fluorescence. Deproteinization (NaOCl; 2%) followed, and lesions of Group 1 (control; n = 20) were etched (HCl; 15%) and externally infiltrated (Icon). Accordingly, the specimens of Group 2 (n = 20) were treated with the resin infiltrant from external; then, internal Class I tunnels were prepared, lesions were internally infiltrated (Icon), and the occlusal cavities were restored (G-ænial Flo X) after etching (H3PO4 gel; 40%). Teeth were cut perpendicular to the proximal lesion surfaces, and percentage infiltrations were analyzed using confocal laser microscopy and a dedicated image manipulation program (GIMP). Regarding the external infiltration, no differences between both groups were detected (P = .114; Mann-Whitney). Additional internal application of the resin infiltrant significantly increased the percentage amount of enamel lesion infiltration (P External and internal infiltration seem to complement the internal tunnel approach, thus remediating the drawbacks of the latter by occluding and stabilizing the porous areas of the proximal caries lesion, and preserving both the marginal ridge and the proximal contact area.

The keystone species of Precambrian deep bedrock biosphere belong to Burkholderiales and Clostridiales

OpenAIRE

L. Purkamo; M. Bomberg; R. Kietäväinen; H. Salavirta; M. Nyyssönen; M. Nuppunen-Puputti; L. Ahonen; I. Kukkonen; M. Itävaara

2015-01-01

The bacterial and archaeal community composition and the possible carbon assimilation processes and energy sources of microbial communities in oligotrophic, deep, crystalline bedrock fractures is yet to be resolved. In this study, intrinsic microbial communities from six fracture zones from 180–2300 m depths in Outokumpu bedrock were characterized using high-throughput amplicon sequencing and metagenomic prediction. Comamonadaceae-, ...

Digital bedrock geologic map of the Gilson Mountain quadrangle,�Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG95-7A Doolan, B, 1995,�Digital bedrock geologic map of the Gilson Mountain quadrangle,�Vermont: VGS Open-File Report VG95-7A, 2 plates, scale...

Pressureless infiltration of porous Al2O3 preform in molten 6061 commercial aluminium alloy

International Nuclear Information System (INIS)

Marin, J.; Olivares, L.; Moreno, C.; Ordonez, S.; Martinez, V.

2001-01-01

This paper presents an infiltration study of Al 2 O 3 samples containing, approximately, 40% of pores with 1μ average radios. These samples were totally infiltrated with Al-6061 at 1100 deg C for 24 hs in air. Microstructural analysis showed the presence of an alumina matrix infiltrated through mechanisms that combine reactive processes and capillarity, and thus being coherent with the presence of open and closed porosity. The metallographic analysis showed open porosity infiltrated with Al-6061 by capillarity, while SEM micrographs corresponding to this system also showed closed pores filled with metal, that was transported into the ceramic matrix through a reactivate infiltration mechanism. The EDAX analysis for the Al 2 O 3 /Al 6061 system showed areas rich in silicon and copper at the metal-ceramic interface, while the ceramic phase showed the presence of Mg. XRD identified the presence of the MgAl 2 O 4 spinel in the ceramic phase

Adductor canal block with local infiltrative analgesia compared with local infiltrate analgesia for pain control after total knee arthroplasty

OpenAIRE

Xing, Qiujuan; Dai, Weiwei; Zhao, Dongfeng; Wu, Ji; Huang, Chunshui; Zhao, Yun

2017-01-01

Abstract Background: This meta-analysis aimed to evaluate the efficiency and safety of the combined adductor canal block with peri-articular infiltration versus periarticular infiltration alone for pain control after total knee arthroplasty (TKA). Methods: PubMed, Medline, Embase, Web of Science, and the Cochrane Library were searched to identify articles comparing the combined adductor canal block with peri-articular infiltration and periarticular infiltration alone for pain control after TK...

Application of spreadsheet to estimate infiltration parameters

OpenAIRE

Zakwan, Mohammad; Muzzammil, Mohammad; Alam, Javed

2016-01-01

Infiltration is the process of flow of water into the ground through the soil surface. Soil water although contributes a negligible fraction of total water present on earth surface, but is of utmost importance for plant life. Estimation of infiltration rates is of paramount importance for estimation of effective rainfall, groundwater recharge, and designing of irrigation systems. Numerous infiltration models are in use for estimation of infiltration rates. The conventional graphical approach ...

Depression storage and infiltration effects on overland flow depth-velocity-friction at desert conditions: field plot results and model

Directory of Open Access Journals (Sweden)

M. J. Rossi

2012-09-01

Full Text Available Water infiltration and overland flow are relevant in considering water partition among plant life forms, the sustainability of vegetation and the design of sustainable hydrological models and management. In arid and semi-arid regions, these processes present characteristic trends imposed by the prevailing physical conditions of the upper soil as evolved under water-limited climate. A set of plot-scale field experiments at the semi-arid Patagonian Monte (Argentina were performed in order to estimate the effect of depression storage areas and infiltration rates on depths, velocities and friction of overland flows. The micro-relief of undisturbed field plots was characterized at z-scale 1 mm through close-range stereo-photogrammetry and geo-statistical tools. The overland flow areas produced by controlled water inflows were video-recorded and the flow velocities were measured with image processing software. Antecedent and post-inflow moisture were measured, and texture, bulk density and physical properties of the upper soil were estimated based on soil core analyses. Field data were used to calibrate a physically-based, mass balanced, time explicit model of infiltration and overland flows. Modelling results reproduced the time series of observed flow areas, velocities and infiltration depths. Estimates of hydrodynamic parameters of overland flow (Reynolds-Froude numbers are informed. To our knowledge, the study here presented is novel in combining several aspects that previous studies do not address simultaneously: (1 overland flow and infiltration parameters were obtained in undisturbed field conditions; (2 field measurements of overland flow movement were coupled to a detailed analysis of soil microtopography at 1 mm depth scale; (3 the effect of depression storage areas in infiltration rates and depth-velocity friction of overland flows is addressed. Relevance of the results to other similar desert areas is justified by the accompanying

A simple analytical infiltration model for short-duration rainfall

Science.gov (United States)

Wang, Kaiwen; Yang, Xiaohua; Liu, Xiaomang; Liu, Changming

2017-12-01

Many infiltration models have been proposed to simulate infiltration process. Different initial soil conditions and non-uniform initial water content can lead to infiltration simulation errors, especially for short-duration rainfall (SHR). Few infiltration models are specifically derived to eliminate the errors caused by the complex initial soil conditions. We present a simple analytical infiltration model for SHR infiltration simulation, i.e., Short-duration Infiltration Process model (SHIP model). The infiltration simulated by 5 models (i.e., SHIP (high) model, SHIP (middle) model, SHIP (low) model, Philip model and Parlange model) were compared based on numerical experiments and soil column experiments. In numerical experiments, SHIP (middle) and Parlange models had robust solutions for SHR infiltration simulation of 12 typical soils under different initial soil conditions. The absolute values of percent bias were less than 12% and the values of Nash and Sutcliffe efficiency were greater than 0.83. Additionally, in soil column experiments, infiltration rate fluctuated in a range because of non-uniform initial water content. SHIP (high) and SHIP (low) models can simulate an infiltration range, which successfully covered the fluctuation range of the observed infiltration rate. According to the robustness of solutions and the coverage of fluctuation range of infiltration rate, SHIP model can be integrated into hydrologic models to simulate SHR infiltration process and benefit the flood forecast.

Modelling of the chemical state in groundwater infiltration systems

International Nuclear Information System (INIS)

Zysset, A.

1993-01-01

Groundwater is replenished by water stemming either from precipitations, lakes or rivers. The area where such an infiltration occurs is characterized by a change in the environmental conditions, such as a decrease of the flow velocity and an increase in the solid surface marking the boundary of the flow field. With these changes new chemical processes may become relevant to the transport behavior of contaminants. Since the rates of chemical processes usually are a function of the concentrations of several species, an understanding of infiltration sites may require a multicomponent approach. The present study aims at formulating a mathematical model together with its numerical solution for groundwater infiltration sites. Such a model should improve the understanding of groundwater quality changes related to infiltrating contaminants. The groundwater quality is of vital interest to men because at many places most of the drinking water originates from groundwater. In the first part of the present study two partial models are formulated: one accounting for the transport in a one-dimensional, homogeneous and saturated porous medium, the other accounting for chemical reactions. This second model is initially stated for general kinetic systems. Then, it is specified for two systems, namely for a system governed only by reactions which are fast compared to the transport processes and for a system with biologically mediated redox reactions of dissolved substrates. In the second part of the study a numerical solution to the model is developed. For this purpose, the two partial models are coupled. The coupling is either iterative as in the case of a system with fast reactions or sequential as in all other cases. The numerical solutions of simple test cases are compared to analytical solutions. In the third part the model is evaluated using observations of infiltration sites reported in the literature. (author) figs., tabs., 155 refs

The bedrock electrical conductivity structure of Northern Ireland

OpenAIRE

Beamish, David

2013-01-01

An airborne geophysical survey of the whole of Northern Ireland has provided over 4.8 M estimates of the bedrock conductivity over the wide range of geological formations present. This study investigates how such data can be used to provide additional knowledge in relation to existing digital geological map information. A by-product of the analysis is a simplification of the spatially aggregated information obtained in such surveys. The methodology used is a GIS-based attribution of the condu...

Analysis of rainfall infiltration law in unsaturated soil slope.

Science.gov (United States)

Zhang, Gui-rong; Qian, Ya-jun; Wang, Zhang-chun; Zhao, Bo

2014-01-01

In the study of unsaturated soil slope stability under rainfall infiltration, it is worth continuing to explore how much rainfall infiltrates into the slope in a rain process, and the amount of rainfall infiltrating into slope is the important factor influencing the stability. Therefore, rainfall infiltration capacity is an important issue of unsaturated seepage analysis for slope. On the basis of previous studies, rainfall infiltration law of unsaturated soil slope is analyzed. Considering the characteristics of slope and rainfall, the key factors affecting rainfall infiltration of slope, including hydraulic properties, water storage capacity (θs - θr), soil types, rainfall intensities, and antecedent and subsequent infiltration rates on unsaturated soil slope, are discussed by using theory analysis and numerical simulation technology. Based on critical factors changing, this paper presents three calculation models of rainfall infiltrability for unsaturated slope, including (1) infiltration model considering rainfall intensity; (2) effective rainfall model considering antecedent rainfall; (3) infiltration model considering comprehensive factors. Based on the technology of system response, the relationship of rainfall and infiltration is described, and the prototype of regression model of rainfall infiltration is given, in order to determine the amount of rain penetration during a rain process.

The influence of subsurface porosity and bedrock composition on ecosystem productivity and drought resilience in the Sierra Nevada Batholith, California

Science.gov (United States)

Riebe, C. S.; Callahan, R. P.; Goulden, M.; Pasquet, S.; Flinchum, B. A.; Taylor, N. J.; Holbrook, W. S.

2017-12-01

The availability of water and nutrients in soil and weathered rock influences the distribution of Earth's terrestrial life and regulates ecosystem vulnerability to land use and climate change. We explored these relationships by combining geochemical and geophysical measurements at three mid-elevation sites in the Sierra Nevada, California. Forest cover correlates strongly with bedrock composition across the sites, implying strong lithologic control on the ecosystem. We evaluated two hypotheses about bedrock-ecosystem connections: 1) that bedrock composition influences vegetation by moderating plant-essential nutrient supply; and 2) that bedrock composition influences the degree of subsurface weathering, which influences vegetation by controlling subsurface water-storage capacity. To quantify subsurface water-holding capacity, we used seismic refraction surveys to infer gradients in P and S-wave velocity structure, which reveal variations in porosity when coupled together in a Hertz-Mindlin rock-physics model. We combined the geophysical data on porosity with bedrock bulk geochemistry measured in previous work to evaluate the influence of water-holding capacity and nutrient supply on ecosystem productivity, which we quantified using remote sensing. Our results show that more than 80% of the variance in ecosystem productivity can be explained by differences in bedrock phosphorus concentration and subsurface porosity, with phosphorus content being the dominant explanatory variable. This suggests that bedrock composition exerts a strong bottom-up control on ecosystem productivity through its influence on nutrient supply and weathering susceptibility, which in turn influences porosity. We show that vegetation vulnerability to drought stress and mortality can be explained in part by variations in subsurface water-holding capacity and rock-derived nutrient supply.

Stormwater infiltration and the 'urban karst' - A review

Science.gov (United States)

Bonneau, Jeremie; Fletcher, Tim D.; Costelloe, Justin F.; Burns, Matthew J.

2017-09-01

The covering of native soils with impervious surfaces (e.g. roofs, roads, and pavement) prevents infiltration of rainfall into the ground, resulting in increased surface runoff and decreased groundwater recharge. When this excess water is managed using stormwater drainage systems, flow and water quality regimes of urban streams are severely altered, leading to the degradation of their ecosystems. Urban streams restoration requires alternative approaches towards stormwater management, which aim to restore the flow regime towards pre-development conditions. The practice of stormwater infiltration-achieved using a range of stormwater source-control measures (SCMs)-is central to restoring baseflow. Despite this, little is known about what happens to the infiltrated water. Current knowledge about the impact of stormwater infiltration on flow regimes was reviewed. Infiltration systems were found to be efficient at attenuating high-flow hydrology (reducing peak magnitudes and frequencies) at a range of scales (parcel, streetscape, catchment). Several modelling studies predict a positive impact of stormwater infiltration on baseflow, and empirical evidence is emerging, but the fate of infiltrated stormwater remains unclear. It is not known how infiltrated water travels along the subsurface pathways that characterise the urban environment, in particular the 'urban karst', which results from networks of human-made subsurface pathways, e.g. stormwater and sanitary sewer pipes and associated high permeability trenches. Seepage of groundwater into and around such pipes is possible, meaning some infiltrated stormwater could travel along artificial pathways. The catchment-scale ability of infiltration systems to restore groundwater recharge and baseflow is thus ambiguous. Further understanding of the fate of infiltrated stormwater is required to ensure infiltration systems deliver optimal outcomes for waterway flow regimes.

Applicability of reflection seismic measurements in detailed characterization of crystalline bedrock

International Nuclear Information System (INIS)

Sireni, S.

2011-03-01

Posiva carried out a seismic survey in the access tunnel of the underground research facility ONKALO in 2009. The survey contributes the detailed characterization of the bedrock in the final disposal of spent nuclear fuel. The aim of this work was to examine the geophysical and geological properties of the chosen tunnel intersections to clarify the important characteristics for reflection generation, and evaluate applicability of this survey for characterization of crystalline bedrock. The seismic result consists of 24 projected amplitude images in 12 different angles. The size of an image is 260*300 m. The amount of digitized reflectors is over 100 and all of them could not be included in this work. The study was limited to 14 intersections that were considered important: brittle fault intersections, tunnel-crosscutting fractures, or lithological contacts. Presence of a brittle fault zone or a tunnel-crosscutting fracture limits the suitable bedrock volume for depositing the nuclear fuel canisters, and wide lithological contacts are a common source of reflection. The seismic data was compared to the existing geological, hydrogeological and geophysical data got from the pilot holes and the tunnel. The most important characteristics were fractures: orientation, fillings, and thickness of the fillings, alteration and water leakage. Geophysically interesting was density, seismic velocities and their products: acoustic impedance and synthetic seismograms. Calculated acoustic impedances showed some differences between cases, but they did not indicate the presence of a reflector. The most common cause of reflector was undulating slickensided, highly altered, tunnel-crosscutting fracture that had thick fracture-fillings and water present. Water was included five times in interpreted reflectors. Also few reflectors were connected to varying mineralogy. Few problematic cases occurred, where a geological feature and a reflection did not correlate, and three of the cases with

Role of slope on infiltration: A review

Science.gov (United States)

Morbidelli, Renato; Saltalippi, Carla; Flammini, Alessia; Govindaraju, Rao S.

2018-02-01

Partitioning of rainfall at the soil-atmosphere interface is important for both surface and subsurface hydrology, and influences many events of major hydrologic interest such as runoff generation, aquifer recharge, and transport of pollutants in surface waters as well as the vadose zone. This partitioning is achieved through the process of infiltration that has been widely investigated at the local scale, and more recently also at the field scale, by models that were designed for horizontal surfaces. However, infiltration, overland flows, and deep flows in most real situations are generated by rainfall over sloping surfaces that bring in additional effects. Therefore, existing models for local infiltration into homogeneous and layered soils and those as for field-scale infiltration, have to be adapted to account for the effects of surface slope. Various studies have investigated the role of surface slope on infiltration based on a theoretical formulations for the dynamics of infiltration, extensions of the Green-Ampt approach, and from laboratory and field experiments. However, conflicting results have been reported in the scientific literature on the role of surface slope on infiltration. We summarize the salient points from previous studies and provide plausible reasons for discrepancies in conclusions of previous authors, thus leading to a critical assessment of the current state of our understanding on this subject. We offer suggestions for future efforts to advance our knowledge of infiltration over sloping surfaces.

Dynamic Water Storage during Flash Flood Events in the Mountainous Area of Rio de Janeiro/Brazil - Case study: Piabanha River Basin

Science.gov (United States)

Araujo, L.; Silva, F. P. D.; Moreira, D. M.; Vásquez P, I. L.; Justi da Silva, M. G. A.; Fernandes, N.; Rotunno Filho, O. C.

2017-12-01

Flash floods are characterized by a rapid rise in water levels, high flow rates and large amounts of debris. Several factors have relevance to the occurrence of these phenomena, including high precipitation rates, terrain slope, soil saturation degree, vegetation cover, soil type, among others. In general, the greater the precipitation intensity, the more likely is the occurrence of a significant increase in flow rate. Particularly on steep and rocky plains or heavily urbanized areas, relatively small rain rates can trigger a flash flood event. In addition, high rain rates in short time intervals can temporarily saturate the surface soil layer acting as waterproofing and favoring the occurrence of greater runoff rates due to non-infiltration of rainwater into the soil. Thus, although precipitation is considered the most important factor for flooding, the interaction between rainfall and the soil can sometimes be of greater importance. In this context, this work investigates the dynamic storage of water associated with flash flood events for Quitandinha river watershed, a tributary of Piabanha river, occurred between 2013 and 2014, by means of water balance analyses applied to three watersheds of varying magnitudes (9.25 km², 260 km² and 429 km²) along the rainy season under different time steps (hourly and daily) using remotely sensed and observational precipitation data. The research work is driven by the hypothesis of a hydrologically active bedrock layer, as the watershed is located in a humid region, having intemperate (fractured) rock layer, just below a shallow soil layer, in the higher part of the basin where steep slopes prevail. The results showed a delay of the variation of the dynamic storage in relation to rainfall peaks and water levels. Such behavior indicates that the surface soil layer, which is not very thick in the region, becomes rapidly saturated along rainfall events. Subsequently, the water infiltrates into the rocky layer and the water

Scintigraphic appearance of focal fatty infiltration of the liver using single-photon emission computed tomography

International Nuclear Information System (INIS)

Kudo, M.; Hirasa, M.; Ibuki, Y.

1984-01-01

Fatty infiltration of the liver had been considered to assume a uniform distribution until quite recently. However, the development of X-ray computed tomography (XCT) and the ultrasound (US) has proven that fatty infiltration of the liver may sometimes assume a nonuniform distribution (focal fatty infiltration (FFI)). This investigation was undertaken to evaluate the scintigraphic appearance of FFI using single-photon emission computed tomography (SPECT) with a GE Maxicamera 400T. Radionuclide images including SPECT were evaluated in 12 cases with FFI which were diagnosed by XCT and US. Most of them were histrogically confirmed to be positive fatty infiltration in the liver. The results were as follows. The fatty infiltrated area was visualized as a hot spot in one case, a defect in 2 cases, a low uptake in one case and a normal uptake in 8 cases. Radionuclide imaging of FFI shows a large variety of findings and it suggests that Kupffer cell function varies with the causes or stage of fatty infiltration. And one can understand the pathological state of FFI from a viewpoint of Kupffer cell function only by radionuclide imaging including SPECT, which is very useful to compare the images with XCT images

Improvement of geological subsurface structure models for Kanto area, Japan, based on records of microtremor array and earthquake observations

Science.gov (United States)

Wakai, A.; Senna, S.; Jin, K.; Cho, I.; Matsuyama, H.; Fujiwara, H.

2017-12-01

To estimate damage caused by strong ground motions from a large earthquake, it is important to accurately evaluate broadband ground-motion characteristics in wide area. For realizing that, it is one of the important issues to model detailed subsurface structure from top surface of seismic bedrock to ground surface.Here, we focus on Kanto area, including Tokyo, where there are thicker sedimentary layers. We, first, have ever collected deep bore-hole data, soil physical properties obtained by some geophysical explorations, geological information and existing models for deep ground from top surface of seismic bedrock to that of engineering bedrock, and have collected a great number of bore-hole data and surficial geological ones for shallow ground from top surface of engineering bedrock to ground surface. Using them, we modeled initial geological subsurface structure for each of deep ground and shallow one. By connecting them appropriately, we constructed initial geological subsurface structure models from top surface of seismic bedrock to ground surface.In this study, we first collected a lot of records obtained by dense microtremor observations and earthquake ones in the whole Kanto area. About microtremor observations, we conducted measurements from large array with the size of hundreds of meters to miniature array with the size of 60 centimeters to cover both of deep ground and shallow one. And then, using ground motion characteristics such as disperse curves and H/V(R/V) spectral ratios obtained from these records, the initial geological subsurface structure models were improved in terms of velocity structure from top surface of seismic bedrock to ground surface in the area.We will report outlines on microtremor array observations, analysis methods and improved subsurface structure models.

Ecohydraulics of Strings and Beads in Bedrock Rivers

Science.gov (United States)

Wohl, E.

2016-12-01

Twenty years ago, Jack Stanford and others described rivers in bedrock canyons as resembling beads on a string when viewed in planform. The beads are relatively wide, low gradient river segments with floodplains, whereas the strings are the intervening steep, narrow river segments with minimal floodplain development. This pattern of longitudinal variations in channel and valley morphology along bedrock canyon rivers is very common, from small channels to major rivers such as the Colorado. Basic understanding of river ecosystems, as well as limited studies, indicates that the beads are more retentive and biologically productive. Although both strings and beads can provide habitat for diverse organisms, strings are more likely to serve as migration corridors, whereas beads provide spawning and nursery habitat, facilitate lateral (channel-floodplain) and vertical (channel-hyporheic) exchanges and associated habitat diversity, and retain dissolved and particulate organic matter. Recognition of the different characteristics and functions of strings and beads can be used to identify their spatial distribution along a river or within a river network and the hydraulically driven processes that sustain channel form, water quality, and biota within strings and beads. Diverse modeling approaches can then be used to quantify the fluxes of water and sediment needed to maintain these hydraulically driven processes. This conceptual framework is illustrated using examples from mountain streams in the Southern Rockies and canyon rivers in the southwestern United States.

Indications of postglacial and recent bedrock movements in Finland and Russian Karelia

Energy Technology Data Exchange (ETDEWEB)

Kuivamaeki, A.; Vuorela, P.; Paananen, M

1998-12-31

This report is mainly a summary report of the studies done 1986 - 1997 by the Geological Survey of Finland/Nuclear Waste Disposal Research on postglacial faulting (PG-faults) and recent bedrock movements. Most of the results have already been published in other YST-reports in Finnish. The first part of the report deals with the postglacial faults in Finland and in the second part the problems connected with the origin and age of paleoseismic dislocations found in Russian Karelia are described. The final part deals with the present vertical and horizontal movements of Finnish bedrock. The Pasmajaervi PG-fault is the most thoroughly studied PG-fault in Finland. Around the fault lineament interpretations and geophysical ground measurements have been done and the fault zone has been penetrated with two drill holes. Three levelling networks and one GPS-network have been established for revealing any recent movements of the PG-fault area. Other PG-faults studied, but not in the same detail, are Venejaervi, Ruostejaervi, Suasselkae and Vaalajaervi PG-faults. The PG-faults in Finland strike in the SW-NE direction and dip to the SE with the exception of the Vaalajaervi PG-fault. It strikes in the NW-SE direction. The dip direction is unknown. The length of the PG-faults is 4-36 km and the scarp height 0-12 m. PG-faults are reverse faults and they are located in old, reactivated fracture zones. The results of drillings and resistivity soundings in the Pasmajaervi PG-fault indicate, that the dip angle of 45 deg in the surface becomes more gentle with the increasing depth. This result may be important from a technical point of view when designing nuclear waste repositories. The strike directions of the PG-faults are perpendicular with the direction of prevailing horizontal maximum stress. The structure and location of the PG-faults is in accordance with the model presented by Muir Wood for the origin of PG-faults. The exceptional direction of the Vaalajaervi PG-fault is

Indications of postglacial and recent bedrock movements in Finland and Russian Karelia

International Nuclear Information System (INIS)

Kuivamaeki, A.; Vuorela, P.; Paananen, M.

1998-01-01

This report is mainly a summary report of the studies done 1986 - 1997 by the Geological Survey of Finland/Nuclear Waste Disposal Research on postglacial faulting (PG-faults) and recent bedrock movements. Most of the results have already been published in other YST-reports in Finnish. The first part of the report deals with the postglacial faults in Finland and in the second part the problems connected with the origin and age of paleoseismic dislocations found in Russian Karelia are described. The final part deals with the present vertical and horizontal movements of Finnish bedrock. The Pasmajaervi PG-fault is the most thoroughly studied PG-fault in Finland. Around the fault lineament interpretations and geophysical ground measurements have been done and the fault zone has been penetrated with two drill holes. Three levelling networks and one GPS-network have been established for revealing any recent movements of the PG-fault area. Other PG-faults studied, but not in the same detail, are Venejaervi, Ruostejaervi, Suasselkae and Vaalajaervi PG-faults. The PG-faults in Finland strike in the SW-NE direction and dip to the SE with the exception of the Vaalajaervi PG-fault. It strikes in the NW-SE direction. The dip direction is unknown. The length of the PG-faults is 4-36 km and the scarp height 0-12 m. PG-faults are reverse faults and they are located in old, reactivated fracture zones. The results of drillings and resistivity soundings in the Pasmajaervi PG-fault indicate, that the dip angle of 45 deg in the surface becomes more gentle with the increasing depth. This result may be important from a technical point of view when designing nuclear waste repositories. The strike directions of the PG-faults are perpendicular with the direction of prevailing horizontal maximum stress. The structure and location of the PG-faults is in accordance with the model presented by Muir Wood for the origin of PG-faults. The exceptional direction of the Vaalajaervi PG-fault is

Final disposal of spent nuclear fuel in Finnish bedrock - Kivetty site report

International Nuclear Information System (INIS)

Anttila, P.; Ahokas, H.; Front, K.

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Kivetty. The bedrock of Kivetty belongs to the large Svecofennian granitoid complex of central Finland, about 1880 million years in age. The most common rock type is porphyritic granodiorite, which is cut by younger medium-grained granodiorite and porphyritic or even-grained granite. Minor bodies of gabbro, older than the porphyritic granodiorite, are also present. The granitoids show evidence of two deformation phases. Altogether 29 bedrock 'structures' (R-structures) have been modelled at the investigation site, most of them representing steeply dipping fracture zones. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 1.3-10 -6 m 2 /s. The corresponding mean of the hydraulic conductivity values for the intact rock, measured using a 2 m packer interval is 4*10 -11 m 2 /s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater of Kivetty is classified as fresh water and

Characterising Bedrock Aquifer Systems in Korea Using Paired Water-Level Monitoring Data

Directory of Open Access Journals (Sweden)

Jae Min Lee

2017-06-01

Full Text Available This study focused on characterising aquifer systems based on water-level changes observed systematically at 159 paired groundwater monitoring wells throughout Korea. Using spectral analysis, principal component analysis (PCA, and cross-correlation analysis with linear regression, aquifer conditions were identified from the comparison of water-level changes in shallow alluvial and deep bedrock monitoring wells. The spectral analysis could identify the aquifer conditions (i.e., unconfined, semi-confined and confined of 58.5% of bedrock wells and 42.8% of alluvial wells: 93 and 68 wells out of 159 wells, respectively. Even among the bedrock wells, 50 wells (53.7% exhibited characteristics of the unconfined condition, implying significant vulnerability of the aquifer to contaminants from the land surface and shallow depths. It appears to be better approach for deep bedrock aquifers than shallow alluvial aquifers. However, significant portions of the water-level changes remained unclear for categorising aquifer conditions due to disturbances in data continuity. For different aquifer conditions, PCA could show typical pattern and factor scores of principal components. Principal component 1 due to wet-and-dry seasonal changes and water-level response time was dominant covering about 55% of total variances of each aquifer conditions, implying the usefulness of supplementary method of aquifer characterisation. Cross-correlation and time-lag analysis in the water-level responses to precipitations clearly show how the water levels in shallow and deep wells correspond in time scale. No significant differences in time-lags was found between shallow and deep wells. However, clear time-lags were found to be increasing from unconfined to confined conditions: from 1.47 to 2.75 days and from 1.78 to 2.75 days for both shallow alluvial and deep bedrock wells, respectively. In combination of various statistical methods, three types of water-level fluctuation

Research of Rainwater Infiltration in Eastern Slovakia

Directory of Open Access Journals (Sweden)

Hudáková Gabriela

2015-11-01

Full Text Available Today precipitation water in the majority of built up and other sealed surface areas no longer reach the water circulation system via natural routes. This can lead to long-term changes to the soil and water resources, reduce the natural local regeneration of the groundwater and have effects on the chemical and biological conditions above and below the ground surface. Reasonable rainwater management leads to maintain or recover a sound and sustainable water cycle. The purpose of this paper is to present objectives and monitoring of a drainage project in Eastern Slovakia, in Kosice city. The paper focuses on percolation facilities in the research area of campus of Technical University and measurements connected with rainwater infiltration.

Digital and preliminary bedrock geologic map of the Pico Peak quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-226A Walsh, G. J., and Ratcliffe, N.M., 1998,�Digital and preliminary bedrock geologic map of the Pico Peak quadrangle, Vermont: USGS...

Digital and preliminary bedrock geologic map of the Mount Carmel quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG98-330A Ratcliffe, N.M., and Walsh, G. J., 1998,�Digital and preliminary bedrock geologic map of the Mount Carmel quadrangle, Vermont: USGS...

Bedrock Geologic Map of the Mount Mansfield 7.5 Minute Quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG2017-2 Thompson, P. J., and Thompson, T. B., 2017, Bedrock Geologic Map of the Mount Mansfield 7.5 Minute Quadrangle, Vermont: VGS Open-File...

Monitoring and modeling infiltration-recharge dynamics of managed aquifer recharge with desalinated seawater

Science.gov (United States)

Ganot, Yonatan; Holtzman, Ran; Weisbrod, Noam; Nitzan, Ido; Katz, Yoram; Kurtzman, Daniel

2017-09-01

We study the relation between surface infiltration and groundwater recharge during managed aquifer recharge (MAR) with desalinated seawater in an infiltration pond, at the Menashe site that overlies the northern part of the Israeli Coastal Aquifer. We monitor infiltration dynamics at multiple scales (up to the scale of the entire pond) by measuring the ponding depth, sediment water content and groundwater levels, using pressure sensors, single-ring infiltrometers, soil sensors, and observation wells. During a month (January 2015) of continuous intensive MAR (2.45 × 106 m3 discharged to a 10.7 ha area), groundwater level has risen by 17 m attaining full connection with the pond, while average infiltration rates declined by almost 2 orders of magnitude (from ˜ 11 to ˜ 0.4 m d-1). This reduction can be explained solely by the lithology of the unsaturated zone that includes relatively low-permeability sediments. Clogging processes at the pond-surface - abundant in many MAR operations - are negated by the high-quality desalinated seawater (turbidity ˜ 0.2 NTU, total dissolved solids ˜ 120 mg L-1) or negligible compared to the low-permeability layers. Recharge during infiltration was estimated reasonably well by simple analytical models, whereas a numerical model was used for estimating groundwater recharge after the end of infiltration. It was found that a calibrated numerical model with a one-dimensional representative sediment profile is able to capture MAR dynamics, including temporal reduction of infiltration rates, drainage and groundwater recharge. Measured infiltration rates of an independent MAR event (January 2016) fitted well to those calculated by the calibrated numerical model, showing the model validity. The successful quantification methodologies of the temporal groundwater recharge are useful for MAR practitioners and can serve as an input for groundwater flow models.

Comparison of infiltration models in NIT Kurukshetra campus

Science.gov (United States)

Singh, Balraj; Sihag, Parveen; Singh, Karan

2018-05-01

The aim of the present investigation is to evaluate the performance of infiltration models used to calculate the infiltration rate of the soils. Ten different locations were chosen to measure the infiltration rate in NIT Kurukshetra. The instrument used for the experimentation was double ring infiltrometer. Some of the popular infiltration models like Horton's, Philip's, Modified Philip's and Green-Ampt were fitted with infiltration test data and performance of the models was determined using Nash-Sutcliffe efficiency (NSE), coefficient of correlation (C.C) and Root mean square error (RMSE) criteria. The result suggests that Modified Philip's model is the most accurate model where values of C.C, NSE and RMSE vary from 0.9947-0.9999, 0.9877-0.9998 to 0.1402-0.6913 (mm/h), respectively. Thus, this model can be used to synthetically produce infiltration data in the absence of infiltration data under the same conditions.

Meningeal infiltration in recurrent nasopharyngeal carcinoma

International Nuclear Information System (INIS)

Chong, V.F.H.; Fan, Y.-F.

2000-01-01

Permeative infiltration of the meninges appears to be a distinct form of recurrent nasopharyngeal carcinoma (NPC). The present report of eight patients with recurrent NPC illustrates meningeal infiltration following basal foramina extension. Seven of the eight patients (88%) showed jugular foramen involvement. Three patients had concomitant infiltration of the foramen magnum. There was one patient showing spread through the foramen lacerum. Only four (50%) of these patients had clinically detectable tumour in the nasopharynx, while the other half showed deep submucosal recurrence with endoscopically unremarkable findings. Permeative meningeal infiltration appears to be a distinct form of NPC recurrence. It is important to recognize this phenomenon so as to optimize the treatment options. The imaging studies were reviewed and the following features were recorded: local nasopharyngeal recurrence, the manner of intracranial spread and site of meningeal infiltration. Four patients had only MRI, two had only CT and two patients had both CT and MRI. The presence or absence of intracranial tumour before treatment was also recorded. Two observers reviewed the images and results were arrived at by consensus. Copyright (1999) Blackwell Science Pty Ltd

Digital compilation bedrock geologic map of part of the Waitsfield quadrangle, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG96-03�Digital compilation bedrock geologic map of part of the Waitsfield quadrangle, Vermont: VGS Open-File Report VG96-3A, 2 plates, scale...

Seasonal Drivers of Dissolved Metal Transport During Infiltration of Road Runoff in an Urban Roadside Environment

Science.gov (United States)

Mullins, A.; Bain, D.

2017-12-01

Infiltration-based green infrastructure (GI) is being increasingly applied in urban areas, systems characterized by substantial legacy contamination and complicated hydrology. However, it is not clear how the application of green infrastructure changes the geochemistry of urban roadside environments. Most current research on GI focuses on small sets of chemical parameters (e.g. road salt, nitrogen and phosphorous species) over relatively short time periods, limiting comprehensive understanding of geochemical function. This work measures changes in groundwater infiltration rate and dissolved metal concentrations in two infiltration trenches in Pittsburgh, PA to evaluate function and measure dissolved metal transport from the system over time. Two distinct geochemical regimes seem to be driven by seasonality: road de-icer exchange and microbial driven summer reducing conditions. Interactions between these geochemical regimes and variability in infiltration rate control the flux of different metals, varying with metal chemistry. These findings suggest the adoption of infiltration based green infrastructure will likely create complicated patterns of legacy contamination transport to downstream receptors.

Influence of bedrock geology on water chemistry of slope wetlands and headwater streams in the southern Rocky Mountains

Science.gov (United States)

Monique LaPerriere Nelson; Charles C. Rhoades; Kathleen A. Dwire

2011-01-01

We characterized the water chemistry of nine slope wetlands and adjacent headwater streams in Colorado subalpine forests and compared sites in basins formed on crystalline bedrock with those formed in basins with a mixture of crystalline and sedimentary bedrock. The pH, Ca2+, Mg2+, NH4 +, acid neutralizing capacity, and electrical conductivity of wetland porewater and...

Digital bedrock geologic map of the Mount Holly and Ludlow quadrangles, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG94-229A Walsh, G.J., Ratcliffe, N.M., Dudley, J.B., and Merrifield, T., 1994,�Digital bedrock geologic map of the Mount Holly and Ludlow...

Investigation of the structure and lithology of bedrock concealed by basin fill, using ground-based magnetic-field-profile data acquired in the San Rafael Basin, southeastern Arizona

Science.gov (United States)

Bultman, Mark W.

2013-01-01

Data on the Earth’s total-intensity magnetic field acquired near ground level and at measurement intervals as small as 1 m include information on the spatial distribution of nearsurface magnetic dipoles that in many cases are unique to a specific lithology. Such spatial information is expressed in the texture (physical appearance or characteristics) of the data at scales of hundreds of meters to kilometers. These magnetic textures are characterized by several descriptive statistics, their power spectrum, and their multifractal spectrum. On the basis of a graphical comparison and textural characterization, ground-based magnetic-field profile data can be used to estimate bedrock lithology concealed by as much as 100 m of basin fill in some cases, information that is especially important in assessing and exploring for concealed mineral deposits. I demonstrate that multifractal spectra of ground-based magnetic-field-profile data can be used to differentiate exposed lithologies and that the shape and position of the multifractal spectrum of the ground-based magnetic-field-profile of concealed lithologies can be matched to the upward-continued multifractal spectrum of an exposed lithology to help distinguish the concealed lithology. In addition, ground-based magnetic-field-profile data also detect minute differences in the magnetic susceptibility of rocks over small horizontal and vertical distances and so can be used for precise modeling of bedrock geometry and structure, even when that bedrock is concealed by 100 m or more of nonmagnetic basin fill. Such data contain valuable geologic information on the bedrock concealed by basin fill that may not be so visible in aeromagnetic data, including areas of hydrothermal alteration, faults, and other bedrock structures. Interpretation of these data in the San Rafael Basin, southeastern Arizona, has yielded results for estimating concealed lithologies, concealed structural geology, and a concealed potential mineral

Evaluation of two stormwater infiltration trenches in central Copenhagen after 15 years of operation

DEFF Research Database (Denmark)

Bergman, Maria Kerstin; Hedegaard, Mathilde Jørgensen; Petersen, Mette Fjendbo

2011-01-01

to see whether the reduction in performance has continued and to determine how the system performs today. Water levels in the trenches were monitored for almost 4 months, and from this period seven events were selected to analyse the infiltration rate. A comparison with similar analyses on storm......Two stormwater infiltration trenches were installed in 1993 in an area in central Copenhagen. The system was monitored continuously for almost three years after establishment, and a small reduction in performance over that time, possibly due to clogging, was noted. A new study was conducted in 2009...... sequences from the first 3 years of operation shows that the infiltration has decreased since the establishment of the system 15 years ago. The decrease is statistically significant (p

Modeling of airborne electromagnetic anomalies related to fractured bedrock and overburden

International Nuclear Information System (INIS)

Peltoniemi, M.; Baers, R.; Vaeisaenen, M.

1993-08-01

Responses of a multifrequency, multicoil airborne electromagnetic (AEM) system were modeled using numerical techniques. Special emphasis was given to poor, three-dimensional electrical conductors embedded both in the bedrock and in the overburden. The results cover vertical coaxial and horizontal coplanar configurations and three frequencies: 888 Hz, 7837 Hz and 51250 Hz. The models studied are signal conductors in free space, and single or multiple conductors embedded in a host rock of high but finite resistivity (5000 Wm) and overlain by a layer of overburden with finite resistivity and thickness. Two different types of computer software were used in the modelling: the free-space PLATE code, and the EM3D set of codes. Modeling results are given both as profiles and as charasteristic diagrams for the various coil configuration - conductor-model combinations. On the basis of the modeling results, limits of detectability for poor conductors have been determined. The study is a part of the preliminary site investigations for the radioactive waste disposal in Finnish bedrock

Quantitative extraction of the bedrock exposure rate based on unmanned aerial vehicle data and Landsat-8 OLI image in a karst environment

Science.gov (United States)

Wang, Hongyan; Li, Qiangzi; Du, Xin; Zhao, Longcai

2017-12-01

In the karst regions of southwest China, rocky desertification is one of the most serious problems in land degradation. The bedrock exposure rate is an important index to assess the degree of rocky desertification in karst regions. Because of the inherent merits of macro-scale, frequency, efficiency, and synthesis, remote sensing is a promising method to monitor and assess karst rocky desertification on a large scale. However, actual measurement of the bedrock exposure rate is difficult and existing remote-sensing methods cannot directly be exploited to extract the bedrock exposure rate owing to the high complexity and heterogeneity of karst environments. Therefore, using unmanned aerial vehicle (UAV) and Landsat-8 Operational Land Imager (OLI) data for Xingren County, Guizhou Province, quantitative extraction of the bedrock exposure rate based on multi-scale remote-sensing data was developed. Firstly, we used an object-oriented method to carry out accurate classification of UAVimages. From the results of rock extraction, the bedrock exposure rate was calculated at the 30 m grid scale. Parts of the calculated samples were used as training data; other data were used for model validation. Secondly, in each grid the band reflectivity of Landsat-8 OLI data was extracted and a variety of rock and vegetation indexes (e.g., NDVI and SAVI) were calculated. Finally, a network model was established to extract the bedrock exposure rate. The correlation coefficient of the network model was 0.855, that of the validation model was 0.677 and the root mean square error of the validation model was 0.073. This method is valuable for wide-scale estimation of bedrock exposure rate in karst environments. Using the quantitative inversion model, a distribution map of the bedrock exposure rate in Xingren County was obtained.

Beneath it all: bedrock geology of the Catskill Mountains and implications of its weathering.

Science.gov (United States)

Ver Straeten, Charles A

2013-09-01

The Devonian-age bedrock of the Catskill Mountains has been the focus of many studies. This paper reviews the character and composition of the rocks of the Catskills, and examines weathering (rock decay) processes and their implications in the Catskills. Rocks of the Catskills and closest foothills consist of siliciclastic rocks (sandstones, mudrocks, conglomerates) with minimal, locally dispersed carbonate rocks. The former are dominated by quartz, metamorphic and sedimentary rock fragments, and clay minerals. Other minor sediment components include cements, authigenic and heavy minerals, and fossil organic matter. Physical, chemical, and biological weathering of the Catskill bedrock since uplift of the Appalachian region, combined with glaciation, have dissected a plateau of nearly horizontally layered rocks into a series of ridges, valleys, and peaks. The varied weathering processes, in conjunction with many factors (natural and anthropogenic), fragment the rocks, forming sediment and releasing various elements and compounds. These may have positive, neutral, or negative implications for the region's soils, waters, ecology, and human usage. A new generation of studies and analyses of the Catskill bedrock is needed to help answer a broad set of questions and problems across various fields of interest. © 2013 New York Academy of Sciences.

Studies of infiltration and lead-soil interactions at the Radioactive Waste Management Site in Area 5 of the Nevada Test Site

International Nuclear Information System (INIS)

Case, C.M.; Davis, J.O.; Heidker, J.C.; Whitbeck, M.R.

1992-07-01

Several studies were conducted to investigate the possibility of buried lead being transported by water in the unsaturated zone at the Area 5 Radioactive Waste Management Site (RWMS) on the Nevada Test Site. All involved soil from a 37-m soil core collected at the RWMS. The core consisted primarily of sand and small pebbles, with occasional layers of loose rocks. Few buried soil horizons were observed, and the core showed no evidence of a carbonate layer that would act as a barrier to infiltration. Samples chosen from various depths in the soil core were analyzed chemically. Calcium and sulfate occurred in a prominent layer about 5 m below the surface. The concentration of soluble carbonate increased gradually with depth, while chloride concentrations decreased. Lead concentrations ranged from 1 to 2 mg/kg. Additional data from the soil core were combined with results of earlier field infiltration studies at two sites near the RWMS to estimate flow velocities for water in the unsaturated zone. Under normal (dry) conditions, the degree of saturation is so small that gravity drainage does not occur; water moves by vapor transport and capillary action. Significant water movement occurs only if the soil is at or near saturation. The results suggest that even continuously ponded water at the RWMS would take several months to infiltrate to the water table. Seven samples from the soil core were tested for their ability to adsorb lead. All took up lead with about the same intensity and capacity. Adsorption of lead by insoluble carbonate minerals and precipitation of lead by soluble carbonate in the soil at the RWMS should provide a barrier to lead migration. Finally, measurements were made of the corrosion rates of lead and steel in contact with soil samples from the core. Corrosion rates generally increased with increasing soil saturation at all depths. Under ambient soil conditions at the RWMS, corrosion rates would be low

Hillslope hydrological modeling : the role of bedrock geometry and hillslope-stream interaction

NARCIS (Netherlands)

Shahedi, K.

2008-01-01

Keywords: Hillslope hydrology, hydrological modeling, bedrock geometry, boundary condition, numerical solution.

This thesis focuses on hillslope subsurface flow as a dominant control on the hydrological processes defining the catchment response to rainfall. Due to the difficulties

Symmetrical parahiliar infiltrated, cough and dyspnoea

International Nuclear Information System (INIS)

Giraldo Estrada, Horacio; Escalante, Hector

2004-01-01

It is the case a patient to who is diagnosed symmetrical parahiliar infiltrated; initially she is diagnosed lymphoma Hodgkin, treaty with radiotherapy and chemotherapy, but the X rays of the thorax demonstrated parahiliars and paramediastinals infiltrated

The SPACE 1.0 model: a Landlab component for 2-D calculation of sediment transport, bedrock erosion, and landscape evolution

Science.gov (United States)

Shobe, Charles M.; Tucker, Gregory E.; Barnhart, Katherine R.

2017-12-01

Models of landscape evolution by river erosion are often either transport-limited (sediment is always available but may or may not be transportable) or detachment-limited (sediment must be detached from the bed but is then always transportable). While several models incorporate elements of, or transition between, transport-limited and detachment-limited behavior, most require that either sediment or bedrock, but not both, are eroded at any given time. Modeling landscape evolution over large spatial and temporal scales requires a model that can (1) transition freely between transport-limited and detachment-limited behavior, (2) simultaneously treat sediment transport and bedrock erosion, and (3) run in 2-D over large grids and be coupled with other surface process models. We present SPACE (stream power with alluvium conservation and entrainment) 1.0, a new model for simultaneous evolution of an alluvium layer and a bedrock bed based on conservation of sediment mass both on the bed and in the water column. The model treats sediment transport and bedrock erosion simultaneously, embracing the reality that many rivers (even those commonly defined as bedrock rivers) flow over a partially alluviated bed. SPACE improves on previous models of bedrock-alluvial rivers by explicitly calculating sediment erosion and deposition rather than relying on a flux-divergence (Exner) approach. The SPACE model is a component of the Landlab modeling toolkit, a Python-language library used to create models of Earth surface processes. Landlab allows efficient coupling between the SPACE model and components simulating basin hydrology, hillslope evolution, weathering, lithospheric flexure, and other surface processes. Here, we first derive the governing equations of the SPACE model from existing sediment transport and bedrock erosion formulations and explore the behavior of local analytical solutions for sediment flux and alluvium thickness. We derive steady-state analytical solutions for

Model and calculations for net infiltration

International Nuclear Information System (INIS)

Childs, S.W.; Long, A.

1992-01-01

In this paper a conceptual model for calculating net infiltration is developed and implemented. It incorporates the following important factors: viability of climate for the next 10,000 years, areal viability of net infiltration, and important soil/plant factors that affect the soil water budget of desert soils. Model results are expressed in terms of occurrence probabilities for time periods. In addition the variability of net infiltration is demonstrated both for change with time and differences among three soil/hydrologic units present at the site modeled

The geology of the Olkiluoto area

International Nuclear Information System (INIS)

Anttila, P.; Paulamaeki, S.; Lindberg, A.; Paananen, M.; Koistinen, T.; Front, K.; Pitkaenen, P.

1992-12-01

Teollisuuden Voima Oy (TVO) is preparing for the final disposal of spent nuclear fuel from the Olkiluoto nuclear power plant deep in the Finnish bedrock. An area close to the power plant at Olkiluoto, Eurajoki, was one of the five areas selected in 1987 for the preliminary site investigations. A summary of the geological conditions at the Olkiluoto site is presented in the report

Seismotechtonic risk modelling for nuclear waste disposal in the Swedish bedrock

International Nuclear Information System (INIS)

Ringdal, F.; Gjoeystdal, H.; Husebye, E.S.

1977-10-01

The problem studied in this report concerns geotectonic risk factors for nuclear waste canisters stored underground in the Swedish bedrock, and embedded in tunnels filled with a clay-like material. The tectonic events causing potential damage can be classed as (i) earthquakes and (ii) creep motion. The numerous existing faults observed in Sweden are in general the results of past orogenic cycles, dating several hundred million years back in time. Only a few faults have shown surface movements after the most recent glaciation (ending about 8000 years b.p.), and in most cases such neotectonic movements have occurred along already existing zones of weakness. A model has been developed to compute the probability of a storage area being intersected by a known or unknown fault. The model is based upon lognormal distribution of fault lengths and a random orientation of the faults with all directions having equal probability of occurrence. The model is used in conjunction with the assumption that the rate of creation of new faults has remained constant over the past 1500 million years, and will remain so in the future. The probability of a new fault created during the next 10,000 years intersecting a given circular storage area of 1 km radius is then of the order 5x10 -6

Modelling of Radionuclide Transport by Groundwater Motion in Fractured Bedrock for Performance Assessment Purposes

International Nuclear Information System (INIS)

Woerman, Anders; Shulan Xu

2003-10-01

Field data of physical properties in heterogeneous crystalline bedrock, like fracture zones, fracture connectivity, matrix porosity and fracture aperture, is associated with uncertainty that can have a significant impact on the analysis of solute transport in fractured rock. The purpose of this study is to develop a performance assessment (PA) model for analyses of radionuclide transport in the geosphere, in which the model takes into account both the effect of heterogeneities of hydrological and geochemical rock properties. By using a travel time description of radionuclide transport in rock fractures, we decompose the transport problem into a one-dimensional mass transfer problem along a distribution of transport pathways and a multi-dimensional flow problem in the fractured bedrock. The hydraulic/flow problem is solved based on a statistical discrete-fracture model (DFM) that represents the network of fractures around the repository and in the surrounding geosphere. A Monte Carlo technique reflects the fact that the representation of the fracture network is uncertain. If the flow residence time PDF exhibits multiple peaks or in another way shows a more erratic hydraulic response on the network scale, the three-dimensional travel time approach is superior to a one-dimensional transport modeling. Examples taken from SITE 94, a study performed by the Swedish Nuclear Power Inspectorate, showed that such cases can be found in safety assessments based on site data. The solute transport is formulated based on partial, differential equations and perturbations (random spatial variability in bedrock properties) are introduced in the coefficients to reflect an uncertainty of the exact appearance of the bedrock associated with the discrete data collection. The combined approach for water flow and solute transport, thereby, recognises an uncertainty in our knowledge in both 1) bedrock properties along individual pathways and 2) the distribution of pathways. Solutions to the

Acceptance-criteria for the bedrock for deep geologic disposal of spent nuclear fuel. Proceedings from a seminar at Gothenburg University

International Nuclear Information System (INIS)

1995-11-01

The seminar was directed to Nordic participants, and discussed disposal in the Nordic crystalline bedrock. Criteria for the bedrock should include: It should give durable mechanical protection for the engineered barriers; give a stable and favorable chemical environment for these barriers; have a low turnover of ground water in the near field; be easy to characterize; give favorable recipient-conditions; not have valuable minerals in workable quantities. These general criteria raise several questions coupled to the safety analysis: e.g. the need for geological, hydrological and geochemical parameters. Which data are missing, which are most difficult to find? What should the site characterization program look like to focus on factors that are of the highest importance according to the safety analysis. The demands on the conditions at a site need to be translated into quantitative criteria, which should be expressed as values that can be measured at the site or deduced from such measurements. These questions were discussed at the seminar, and 21 contributions from Finnish, Norwegian and Swedish participants are reported in these proceedings under the chapters: Coupling to the safety analysis; Methodology and criteria for site selection in a regional geoscientific perspective; Rock as a building material - prognosis and result; Geoscientific criteria for the bedrock at the repository - Mechanical protection; Geoscientific criteria for the bedrock at the repository - Low ground water turnover, chemically favorable and stable environment in the near field; Geoscientific criteria for the bedrock at the repository - Demands on the bedrock concerning the migration of radionuclides

Toward improved prediction of the bedrock depth underneath hillslopes: Bayesian inference of the bottom-up control hypothesis using high-resolution topographic data

Science.gov (United States)

Gomes, Guilherme J. C.; Vrugt, Jasper A.; Vargas, Eurípedes A.

2016-04-01

The depth to bedrock controls a myriad of processes by influencing subsurface flow paths, erosion rates, soil moisture, and water uptake by plant roots. As hillslope interiors are very difficult and costly to illuminate and access, the topography of the bedrock surface is largely unknown. This essay is concerned with the prediction of spatial patterns in the depth to bedrock (DTB) using high-resolution topographic data, numerical modeling, and Bayesian analysis. Our DTB model builds on the bottom-up control on fresh-bedrock topography hypothesis of Rempe and Dietrich (2014) and includes a mass movement and bedrock-valley morphology term to extent the usefulness and general applicability of the model. We reconcile the DTB model with field observations using Bayesian analysis with the DREAM algorithm. We investigate explicitly the benefits of using spatially distributed parameter values to account implicitly, and in a relatively simple way, for rock mass heterogeneities that are very difficult, if not impossible, to characterize adequately in the field. We illustrate our method using an artificial data set of bedrock depth observations and then evaluate our DTB model with real-world data collected at the Papagaio river basin in Rio de Janeiro, Brazil. Our results demonstrate that the DTB model predicts accurately the observed bedrock depth data. The posterior mean DTB simulation is shown to be in good agreement with the measured data. The posterior prediction uncertainty of the DTB model can be propagated forward through hydromechanical models to derive probabilistic estimates of factors of safety.

New Mass-Conserving Bedrock Topography for Pine Island Glacier Impacts Simulated Decadal Rates of Mass Loss

Science.gov (United States)

Nias, I. J.; Cornford, S. L.; Payne, A. J.

2018-04-01

High-resolution ice flow modeling requires bedrock elevation and ice thickness data, consistent with one another and with modeled physics. Previous studies have shown that gridded ice thickness products that rely on standard interpolation techniques (such as Bedmap2) can be inconsistent with the conservation of mass, given observed velocity, surface elevation change, and surface mass balance, for example, near the grounding line of Pine Island Glacier, West Antarctica. Using the BISICLES ice flow model, we compare results of simulations using both Bedmap2 bedrock and thickness data, and a new interpolation method that respects mass conservation. We find that simulations using the new geometry result in higher sea level contribution than Bedmap2 and reveal decadal-scale trends in the ice stream dynamics. We test the impact of several sliding laws and find that it is at least as important to accurately represent the bedrock and initial ice thickness as the choice of sliding law.

2D SPLASH: a new method to determine the fatty infiltration of the rotator cuff muscles

International Nuclear Information System (INIS)

Kenn, Werner; Huemmer, Christian; Koestler, Herbert; Hahn, Dietbert; Boehm, Dirk; Gohlke, Frank

2004-01-01

The objective of this paper is to quantify the fatty degeneration (infiltration) of rotator cuff muscles with a new spectroscopic FLASH (SPLASH) sequence. Before planned surgery (reconstruction or muscle transfer), 20 patients (13 men, 7 women; 35-75 years) with different stages of rotator cuff disease underwent an MR examination in a 1.5-T unit. The protocol consists of imaging sequences and a newly implemented SPLASH, which allows an exact quantification of the fat/water ratio with a high spatial resolution in an arbitrarily shaped region of interest (ROI). The percentages of fat in the rotator cuff muscles were determined. To determine statistically significant differences between the different stages of rotator cuff tear, a Kruskal-Wallis H test was used. Fatty infiltration of the supraspinatus muscle was correlated with cross-sectional area (CSA) measures (Bravais-Pearson). We found significant differences between different stages of rotator cuff disease, the fatty infiltration and the volume loss (determined by the occupation ratio) of the supraspinatus muscle. With the increasing extent of rotator cuff disease, fatty infiltration increases significantly, as does the volume loss of the supraspinatus muscle. Comparing fatty infiltration and the occupation ratio individually, there was only a moderate inverse correlation between fatty infiltration and the occupation ratio, with considerable variation of data. Fatty infiltration of the infraspinatus muscle occurred when the infraspinatus tendon was involved to a lesser extent. The SPLASH sequence allows exact quantification of fatty infiltration in an arbitrarily shaped ROI. The extent of atrophy and fatty infiltration correlates with the size of the tear. Atrophy and fatty infiltration correlate only moderately and should be evaluated separately. (orig.)

Bedrock geologic map of the northern Alaska Peninsula area, southwestern Alaska

Science.gov (United States)

Wilson, Frederic H.; Blodgett, Robert B.; Blome, Charles D.; Mohadjer, Solmaz; Preller, Cindi C.; Klimasauskas, Edward P.; Gamble, Bruce M.; Coonrad, Warren L.

2017-03-03

The northern Alaska Peninsula is a region of transition from the classic magmatic arc geology of the Alaska Peninsula to a Proterozoic and early Paleozoic carbonate platform and then to the poorly understood, tectonically complex sedimentary basins of southwestern Alaska. Physiographically, the region ranges from the high glaciated mountains of the Alaska-Aleutian Range to the coastal lowlands of Cook Inlet on the east and Bristol Bay on the southwest. The lower Ahklun Mountains and finger lakes on the west side of the map area show strong effects from glaciation. Structurally, a number of major faults cut the map area. Most important of these are the Bruin Bay Fault that parallels the coast of Cook Inlet, the Lake Clark Fault that cuts diagonally northeast to southwest across the eastern part of the map area, and the presently active Holitna Fault to the northwest that cuts surficial deposits.Distinctive rock packages assigned to three provinces are overlain by younger sedimentary rocks and intruded by widely dispersed latest Cretaceous and (or) early Tertiary granitic rocks. Much of the east half of the map area lies in the Alaska-Aleutian Range province; the Jurassic to Tertiary Alaska-Aleutian Range batholith and derivative Jurassic sedimentary rocks form the core of this province, which is intruded and overlain by the Aleutian magmatic arc. The Lime Hills province, the carbonate platform, occurs in the north-central part of the map area. The Paleozoic and Mesozoic Ahklun Mountains province in the western part of the map area includes abundant chert, argillite, and graywacke and lesser limestone, basalt, and tectonic mélange. The Kuskokwim Group, an Upper Cretaceous turbidite sequence, is extensively exposed and bounds all three provinces in the west-central part of the map area.

Fractured Epikarst Bedrock as Water Source for Woody Plants in Savanna

Science.gov (United States)

Schwinning, S.; Goodsheller, K. R.; Schwartz, B. F.

2010-12-01

Study of the soil-vegetation-atmosphere system has been overwhelmingly dominated by systems with deep soils, yet large portions of the world are characterized by shallow soils underlain by fractured bedrock. In these systems, fractured bedrock may provide significant water storage, but we know little about the function of fractured bedrock as a water source for plants. In this study we examined the water use of three co-dominant tree species on the eastern rim of the karstic Edwards Plateau where the soil is extremely rocky, only 20 -30 cm thick, and overlies a well-developed epikarst. We used Granier sap flow sensors to estimate changes in sapflow velocity with the onset of summer drought. Simultaneously, we measured precipitation inputs and drip rates in a shallow cave below the field site. Precipitation, stem and drip water were also periodically sampled for stable isotope analysis to match stem water with potential source waters. The year of the study, 2009, was characterized by extreme drought conditions developing during summer. Sap flow rates began to decline in mid-May for all three species, but there were distinct species differences in the development of water stress: live oak (Quercus fusiformis) was the first to show significant loss of transpiration, reaching minimal sap flow values by early June. Cedar elm (Ulmus crassifolia) reached minimal sap flow values by early July, while Ashe juniper’s (Juniperus ashei) loss of transpiration was very gradual, continuing to decline until early August. The isotope ratios of hydrogen and oxygen in water were not significantly different between species, suggesting that root development and water uptake was similarly constrained for the three species. In summer, all stem water isotope ratios were enriched relative to precipitation, while all drip waters coincided with the local meteoric water line. This suggests that tree water sources were relatively shallow and water draining out of the root zone did not have a

Influence of Surface Biosolids Application on Infiltration

Directory of Open Access Journals (Sweden)

Richard E. Zartman

2012-01-01

Full Text Available Biosolids from waste water treatment facilities applied to soils not only add plant nutrients, but also increase infiltration and decrease runoff and erosion. Wet biosolids from New York, NY, were surface applied at 0 to 90 Mg ha−1 dry weight to soils near El Paso, Tex. Simulated rainfall intensities of 16.4 cm hr−1 for 30 minutes applied to 0.5 m2 soil plots yielded initial infiltration rates of ~16 cm hr−1 for all plots. Biosolids applications extended the duration of the initially high infiltration rates. After 30 minutes, infiltration rates for bare soil were 3 cm hr−1 without and 10 cm hr−1 with 90 Mg biosolids ha−1. Applied biosolids, plant litter, surface gravel, and plant base contributed surface cover, which absorbed raindrop energy and reduced erosion. Biosolids increased cumulative infiltration on the vegetated, wet soils more than for the dry or bare soils. Biosolids increased cumulative infiltration from 2 to 6 cm on a bare gravelly soil and from 9.3 to 10.6 cm on a vegetated soil.

Field Study of Infiltration Capacity Reduction of Porous Mixture Surfaces

Directory of Open Access Journals (Sweden)

Luis A. Sañudo-Fontaneda

2014-03-01

Full Text Available Porous surfaces have been used all over the world in source control techniques to minimize flooding problems in car parks. Several studies highlighted the reduction in the infiltration capacity of porous mixture surfaces after several years of use. Therefore, it is necessary to design and develop a new methodology to quantify this reduction and to identify the hypothetical differences in permeability between zones within the same car park bay due to the influence of static loads in the parked vehicles. With this aim, nine different zones were selected in order to check this hypothesis (four points under the wheels of a standard vehicle and five points between wheels. This article presents the infiltration capacity reduction results, using the LCS permeameter, of Polymer-Modified Porous Concrete (9 bays and Porous Asphalt (9 bays surfaces in the University of Cantabria Campus parking area (Spain 5 years after their construction. Statistical analysis methodology was proposed for assessing the results. Significant differences were observed in permeability and reduction in infiltration capacity in the case of porous concrete surfaces, while no differences were found for porous asphalt depending on the measurement zone.

Final disposal of spent nuclear fuel in Finnish bedrock - Kivetty site report

Energy Technology Data Exchange (ETDEWEB)

Anttila, P. [Fortum Engineering Oy, Vantaa (Finland); Ahokas, H.; Front, K. [Fintact Oy (Finland)] [and others

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Kivetty. The bedrock of Kivetty belongs to the large Svecofennian granitoid complex of central Finland, about 1880 million years in age. The most common rock type is porphyritic granodiorite, which is cut by younger medium-grained granodiorite and porphyritic or even-grained granite. Minor bodies of gabbro, older than the porphyritic granodiorite, are also present. The granitoids show evidence of two deformation phases. Altogether 29 bedrock 'structures' (R-structures) have been modelled at the investigation site, most of them representing steeply dipping fracture zones. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 1.3-10{sup -6} m{sup 2}/s. The corresponding mean of the hydraulic conductivity values for the intact rock, measured using a 2 m packer interval is 4*10{sup -11} m{sup 2}/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater of

Analysis of Rainfall Infiltration Law in Unsaturated Soil Slope

OpenAIRE

Zhang, Gui-rong; Qian, Ya-jun; Wang, Zhang-chun; Zhao, Bo

2014-01-01

In the study of unsaturated soil slope stability under rainfall infiltration, it is worth continuing to explore how much rainfall infiltrates into the slope in a rain process, and the amount of rainfall infiltrating into slope is the important factor influencing the stability. Therefore, rainfall infiltration capacity is an important issue of unsaturated seepage analysis for slope. On the basis of previous studies, rainfall infiltration law of unsaturated soil slope is analyzed. Considering t...

Neoseismotectonics and glacial isostatic uplift. Deformations and changes of prevailing conditions in the Swedish bedrock

Energy Technology Data Exchange (ETDEWEB)

Moerner, N.A. [Stockholm Univ. (Sweden)

1997-04-01

The conclusions from this contribution are that no bedrock repository can be considered to be safely placed in the bedrock at the event of new glaciations, which are to be expected over Sweden in 5, 23, and 60 thousand years AP (following the astronomical, natural or long-term variability). Instead, there are all reasons to expect that such a repository would be seriously damaged, and constitute a threat to the biosphere on Earth. These conclusions are based on an extensive observational network of records on the multiple glacial dynamics and the interaction of different variables. 24 refs.

Neoseismotectonics and glacial isostatic uplift. Deformations and changes of prevailing conditions in the Swedish bedrock

International Nuclear Information System (INIS)

Moerner, N.A.

1997-01-01

The conclusions from this contribution are that no bedrock repository can be considered to be safely placed in the bedrock at the event of new glaciations, which are to be expected over Sweden in 5, 23, and 60 thousand years AP (following the astronomical, natural or long-term variability). Instead, there are all reasons to expect that such a repository would be seriously damaged, and constitute a threat to the biosphere on Earth. These conclusions are based on an extensive observational network of records on the multiple glacial dynamics and the interaction of different variables. 24 refs

Project Work Plan: Sequestration of Strontium-90 Subsurface Contamination in the Hanford 100-N Area by Surface Infiltration of an Apatite Solution

Energy Technology Data Exchange (ETDEWEB)

Szecsody, Jim E.

2006-04-30

We propose to develop an infiltration strategy that defines the precipitation rate of an apatite-forming solution and Sr-90 sequestration processes under variably saturated (low water content) conditions. We will develop this understanding through small-scale column studies, intermediate-scale two-dimensional (2-D) experiments, and numerical modeling to quantify individual and coupled processes associated with apatite formation and Sr-90 transport during and after infiltration of the Ca-citrate-PO4 solution. Development of capabilities to simulate these coupled biogeochemical processes during both injection and infiltration will be used to determine the most cost-effective means to emplace an in situ apatite barrier with a longevity of 300 years to permanently sequester Sr-90 until it decays. Biogeochemical processes that will be investigated are citrate biodegradation and apatite precipitation rates at varying water contents as a function of water content. Coupled processes that will be investigated include the influence of apatite precipitation (which occupies pore space) on the hydraulic and transport properties of the porous media during infiltration.

Controls on sediment cover in bedrock-alluvial channels of the Henry Mountains, Utah

Science.gov (United States)

Hodge, R. A.; Yager, E.; Johnson, J. P.; Tranmer, A.

2017-12-01

The location and extent of sediment cover in bedrock-alluvial channels influences sediment transport rates, channel incision and instream ecology. However, factors affecting sediment cover and how it responds to changes in relative sediment supply have rarely been quantitatively evaluated in field settings. Using field surveys and SFM analysis of channel reach topography, we quantified sediment cover and channel properties including slope, width, grain size distributions, and bedrock and alluvial roughness in North Wash and Chelada Creek in the Henry Mountains, Utah. Along reaches where upstream sediment supply does not appear to be restricted, we find that the fraction of local bedrock exposure increases as a function of local relative transport capacity . In a downstream section of Chelada Creek, decadal-scale sediment supply has been restricted by an upstream culvert that has caused a backwater effect and corresponding upstream deposition. In this section, alluvial cover is uncorrelated with local stream power. To test the impact of relative sediment supply on sediment cover, a 1D sediment transport model was used to predict the equilibrium sediment cover in Chelada Creek under varying flow and sediment supply conditions. Sediment transport in each model section was predicted using the partial cover model of Johnson (2015), which accounts for differences in bedrock and alluvial roughness on critical shear stress and flow resistance. Model runs in which sediment supply was approximately equal to mean transport capacity produced a pattern of sediment cover which best matched the field observations upstream of the culvert. However, runs where sediment supply was under-capacity produced the pattern most similar to field observations downstream of the culvert, consistent with our field-based interpretations. Model results were insensitive to initial sediment cover, and equilibrium was relatively quickly reached, suggesting that the channel is responsive to changes in

Radiology and pathology correlation in common infiltrative cardiomyopathies

International Nuclear Information System (INIS)

Varzeshi, Neda; Hansen, Mark; Rezaee, Amir; Slaughter, Richard; Dixon, Natalie; Duhig, Edwina

2012-01-01

Infiltrative cardiomyopathies generally pose a diagnostic dilemma as current diagnostic tools are imprecise. Invasive endomyocardial biopsy is considered as the gold standard however it has some limitations. Recently cardiovascular magnetic resonance (CMR) is emerging as an excellent technique in diagnosing infiltrative cardiomyopathies and is increasingly being used. Characteristic pathologic and radiologic findings in most common infiltrative cardiomyopathies (amyloid, sarcoid and Fabry's) are discussed and correlated with relative CMR and histologic examples. There is fairly good correlation between the non-invasive radiologic and the invasive histologic findings in common infiltrative cardiomyopathies. Non-invasive CMR with its high sensitivity and specificity has an excellent role in establishing the diagnosis and improving the prognosis of common infiltrative cardiomyopathies.

Interpretation of ponded infiltration data using numerical experiments

Directory of Open Access Journals (Sweden)

Dohnal Michal

2016-09-01

Full Text Available Ponded infiltration experiment is a simple test used for in-situ determination of soil hydraulic properties, particularly saturated hydraulic conductivity and sorptivity. It is known that infiltration process in natural soils is strongly affected by presence of macropores, soil layering, initial and experimental conditions etc. As a result, infiltration record encompasses a complex of mutually compensating effects that are difficult to separate from each other. Determination of sorptivity and saturated hydraulic conductivity from such infiltration data is complicated. In the present study we use numerical simulation to examine the impact of selected experimental conditions and soil profile properties on the ponded infiltration experiment results, specifically in terms of the hydraulic conductivity and sorptivity evaluation. The effect of following factors was considered: depth of ponding, ring insertion depth, initial soil water content, presence of preferential pathways, hydraulic conductivity anisotropy, soil layering, surface layer retention capacity and hydraulic conductivity, and presence of soil pipes or stones under the infiltration ring. Results were compared with a large database of infiltration curves measured at the experimental site Liz (Bohemian Forest, Czech Republic. Reasonably good agreement between simulated and observed infiltration curves was achieved by combining several of factors tested. Moreover, the ring insertion effect was recognized as one of the major causes of uncertainty in the determination of soil hydraulic parameters.

Infiltration of runoff rainwater and transfer of the associated pollutants in the urban ground - towards a global and multi-disciplinary approach; Infiltration des eaux de ruissellement pluvial et transfert de polluants associes dans le sol urbain - vers une approche globale et pluridisciplinaire

Energy Technology Data Exchange (ETDEWEB)

Martinelli, I.

1999-12-01

Storm water run-off infiltration now appears as a supplementary or alternative strategy to gravitational drainage systems. The present study sought to draw up a framework to represent pollutant transfer in such infiltration, this phenomenon being governed by various physical, chemical and biological processes. Study of the literature was able on the one hand to specify urban storm water run-off pollution, and, on the other, to identify the various possible processes undergone or induced during infiltration in the soil. It was noted that experimentation in this area requires certain extra input, whether, at laboratory level, for studying interactions effects between several pollutants and several processes, or, in the field, for a better account of soil heterogeneity and of integration of various elementary phenomena. Nevertheless, the state of knowledge regarding these levels and various scientific areas made it possible to identify the main parameters seeming to govern pollutant transfer. A representation was drawn up of the soil underlying a storm water run-off infiltration system, and a experimental framework proposed both to validate and to enhance the present model. (author)

Dosimetric implications of the infiltrated injection

International Nuclear Information System (INIS)

Castronovo, F.P.; McKusick, K.A.; Strauss, H.W.

1984-01-01

Following inadvertent infiltration of a radiopharmaceutical, there is variable and uncertain uptake in target tissue. Concomitantly, there is also a concern for the radiation dose to the infiltrated site. This investigation determined the clearance and radiation burdens from various radiopharmaceutical infiltrates in a rat model. Nine separate sites were studied for: Tc-99m microspheres; Tc-99m MDP; Ga-67 citrate; and Tl-201 chloride. Following sc injection on the shaven posteriors of anesthetized adult male Sprague-Dawley rats, gamma camera and computer data were collected up to 24 hours. The resulting data were expressed semilogarithmically as the mean (N = 9) of the ''% retained at site'' as a f(time) after injection. Nonparticulate agents showed a tri-exponential release pattern from each site, whereas the microspheres remained for an extended period of time. Using these pharma-cokinetic curves, the % remaining at each site for various times, and rems/mCi per lcc infiltrate was determined

40 CFR 35.927-1 - Infiltration/inflow analysis.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 1 2010-07-01 2010-07-01 false Infiltration/inflow analysis. 35.927-1... ASSISTANCE STATE AND LOCAL ASSISTANCE Grants for Construction of Treatment Works-Clean Water Act § 35.927-1 Infiltration/inflow analysis. (a) The infiltration/inflow analysis shall demonstrate the nonexistence or...

Radiomic signature of infiltration in peritumoral edema predicts subsequent recurrence in glioblastoma: implications for personalized radiotherapy planning.

Science.gov (United States)

Rathore, Saima; Akbari, Hamed; Doshi, Jimit; Shukla, Gaurav; Rozycki, Martin; Bilello, Michel; Lustig, Robert; Davatzikos, Christos

2018-04-01

Standard surgical resection of glioblastoma, mainly guided by the enhancement on postcontrast T1-weighted magnetic resonance imaging (MRI), disregards infiltrating tumor within the peritumoral edema region (ED). Subsequent radiotherapy typically delivers uniform radiation to peritumoral FLAIR-hyperintense regions, without attempting to target areas likely to be infiltrated more heavily. Noninvasive in vivo delineation of the areas of tumor infiltration and prediction of early recurrence in peritumoral ED could assist in targeted intensification of local therapies, thereby potentially delaying recurrence and prolonging survival. This paper presents a method for estimating peritumoral edema infiltration using radiomic signatures determined via machine learning methods, and tests it on 90 patients with de novo glioblastoma. The generalizability of the proposed predictive model was evaluated via cross-validation in a discovery cohort ([Formula: see text]) and was subsequently evaluated in a replication cohort ([Formula: see text]). Spatial maps representing the likelihood of tumor infiltration and future early recurrence were compared with regions of recurrence on postresection follow-up studies with pathology confirmation. The cross-validated accuracy of our predictive infiltration model on the discovery and replication cohorts was 87.51% (odds ratio = 10.22, sensitivity = 80.65, and specificity = 87.63) and 89.54% (odds ratio = 13.66, sensitivity = 97.06, and specificity = 76.73), respectively. The radiomic signature of the recurrent tumor region revealed higher vascularity and cellularity when compared with the nonrecurrent region. The proposed model shows evidence that multiparametric pattern analysis from clinical MRI sequences can assist in in vivo estimation of the spatial extent and pattern of tumor recurrence in peritumoral edema, which may guide supratotal resection and/or intensification of postoperative radiation therapy.

A systematic study of distribution characters of infiltration parameters in an experimental basin by nuclear methods

International Nuclear Information System (INIS)

Gu Weizu; Lu Jieju; Lu Mingjiang; Chen Tingyang

1988-01-01

A case study of spatial variability of Philip's infiltration parameters was carried out in a small experimental catchment with an area of 0.8 ha by nuclear monitoring methods. Relationships between sorptivity S, parameter A and the average initial soil water content within 0.5 m depth of soil profiles over the catchment have been plotted. A watershed infiltration parameter distribution curve is set up and fitted approximately by f/F=1-(1-S/S M ) n . The parameters of composite infiltration response related to whole catchment are suggested. The author has studied it on an experimental basin by combined method of nuclear technology and micro-geomorphic analysis. The results are satisfactory. (author). 6 refs, 11 figs, 2 tabs

Relationship between Microcalcification and infiltration in breast cancer

International Nuclear Information System (INIS)

Park, Tai Que; Jeon, Mal Soon; Kim, Yang Sook

1990-01-01

Microcalcification is one of the most common findings in breast cancer and most of cases with microcalcification only reveal non infiltrating type of cancer and better prognosis. We analysed 70 cases of breast cancer pathologically proved among 2,115 patients that underwent xermammography from 1983. 10.1 to 1989. 7. 30 and studied relationship between xerographic findings and nature of infiltration in breast cancer. The results were as follows: 1. Among 2,115 patients which were performed xeromammography, 70 cases were pathologically proved breast cancer and incident was 3.3%. 2. Incidence of breast cancer in terms of age was 0.2% in third decade. 1.2% in fourth decade, 4.4% in fifth decade, 14.3% in sixth decade, 15 % over seventh decade. Of total 70 patients, 51 cases were included over fifth decade. 3. Xeromammgraphy findings were classified microcalcification only, mass only, microcalcification with mass. Incidence of xerography findings such as microcalcification only (22%) was less than that of mass density (78%). 4. In 16 cases of microcalcification only. Incidence below 50 years (75%) were more than that over 50 (25%). 5. Infiltrating breast cancers (67%) were more than non-infiltrating breast cancer (33%) and number of non-infiltrating breast cancer with xerographic findings of microcalcification only (56%) was no more than that of infiltrating breast cancer (44%) but number of infiltrating breast cancer with mass (75%) was much more than non-infiltrating breast cancer (25%)

Subglacial hydrology of the lake district ice lobe during the Younger Dryas (ca. 12 500 - 11 600 years ago) in the Kylaeniemi area, SE Finland

Energy Technology Data Exchange (ETDEWEB)

Lunkka, J. P.; Moisio, K.; Vainio, A. [Univ. of Oulu (Finland)

2013-07-15

It is essential to gain knowledge on the subglacial hydrological conditions at the glacier bed / bedrock interface when assessing how bedrock fracture zones affect subglacial melt water flow and in which subglacial zones pressurized and oxygen-rich melt water penetrates into the bedrock fracture systems. In the warm-based glacier zones, a part of subglacial melt water will penetrate deep into the fracture systems although the major part of melt water is drained to and beyond the ice margin via subglacial tunnel networks especially in the areas where ice is flowing on the crystalline bedrock. During the last deglaciation phase of the former Scandinavian Ice Sheet, glaciofluvial accumulations were deposited and these sediment accumulations are highly important when picturing the subglacial hydrology of different ice streams during deglaciation in the crystalline bedrock area. The aim of the present work was to map the bedrock fracture zones in the Kylaeniemi area and to shed light on the subglacial hydrology of the Scandinavian Ice Sheet's Lake District Ice Stream that occupied the Kylaeniemi area during the Younger Dryas between ca. 12 500 - 11 600 years ago. The special emphasis within this general aim was to study the relationship between bedrock fracture zones and the routes of subglacial drainage paths. The methods used to map and study bedrock fracture zones and subglacial drainage paths included remotes sensing methods, field observations, ground penetrating radar (GPR) investigations and GIS-based reconstructions. Conventional geological field methods aided by the GPR-method were also used to map bedrock exposures and their structures and to define the type of glaciofluvial sediments and glaciofluvial landform associations. Two main fracture zone sets occur in the study area. The most prominent bedrock fracture zone set trends NW-SE while the other, less prominent fracture zone set is aligned in NE-SW direction. The majority of the minor joint sets in

Subglacial hydrology of the lake district ice lobe during the Younger Dryas (ca. 12 500 - 11 600 years ago) in the Kylaeniemi area, SE Finland

International Nuclear Information System (INIS)

Lunkka, J. P.; Moisio, K.; Vainio, A.

2013-07-01

It is essential to gain knowledge on the subglacial hydrological conditions at the glacier bed / bedrock interface when assessing how bedrock fracture zones affect subglacial melt water flow and in which subglacial zones pressurized and oxygen-rich melt water penetrates into the bedrock fracture systems. In the warm-based glacier zones, a part of subglacial melt water will penetrate deep into the fracture systems although the major part of melt water is drained to and beyond the ice margin via subglacial tunnel networks especially in the areas where ice is flowing on the crystalline bedrock. During the last deglaciation phase of the former Scandinavian Ice Sheet, glaciofluvial accumulations were deposited and these sediment accumulations are highly important when picturing the subglacial hydrology of different ice streams during deglaciation in the crystalline bedrock area. The aim of the present work was to map the bedrock fracture zones in the Kylaeniemi area and to shed light on the subglacial hydrology of the Scandinavian Ice Sheet's Lake District Ice Stream that occupied the Kylaeniemi area during the Younger Dryas between ca. 12 500 - 11 600 years ago. The special emphasis within this general aim was to study the relationship between bedrock fracture zones and the routes of subglacial drainage paths. The methods used to map and study bedrock fracture zones and subglacial drainage paths included remotes sensing methods, field observations, ground penetrating radar (GPR) investigations and GIS-based reconstructions. Conventional geological field methods aided by the GPR-method were also used to map bedrock exposures and their structures and to define the type of glaciofluvial sediments and glaciofluvial landform associations. Two main fracture zone sets occur in the study area. The most prominent bedrock fracture zone set trends NW-SE while the other, less prominent fracture zone set is aligned in NE-SW direction. The majority of the minor joint sets in

Water infiltration into homogeneous soils: a new concept

International Nuclear Information System (INIS)

Manfredni, S.

1977-10-01

A new concept for the analytical description of the process of water infiltration into homogeneous soils is presented. The concept uses a new definition of a 'gravitational diffusivity' which permits the generalization of both cases, horizontal and vertical infiltration. The efficiency of the new concept in describing the infiltration process, for short and intermediate times, is proved through experimental data obtained during water infiltration into air-dry soil columns. Its advantages are discussed comparing soil water contents predicted by the numerical solution proposed by PHILLIP (1955, 1957) [pt

Anisotropic modelling of the electrical conductivity of fractured bedrock

International Nuclear Information System (INIS)

Flykt, M.J.; Sihvola, A.H.; Eloranta, E.H.

1995-01-01

The electromagnetic characterization of fractured bedrock is of importance when studying the final disposal of nuclear waste. The different types of discontinuities at all scales in rocks can be viewed as an inhomogeneity. In some cases there are reasons to assume the influence of the discontinuities on electrical conductivity is anisotropic in character. The effort has been made to use electromagnetic mixing rules in the definition of an equivalent homogeneous anisotropic conductivity tensor for such fractured rock mass. (author) (16 refs., 6 figs.)

Difference infiltrometer: a method to measure temporally variable infiltration rates during rainstorms

Science.gov (United States)

Moody, John A.; Ebel, Brian A.

2012-01-01

We developed a difference infiltrometer to measure time series of non-steady infiltration rates during rainstorms at the point scale. The infiltrometer uses two, tipping bucket rain gages. One gage measures rainfall onto, and the other measures runoff from, a small circular plot about 0.5-m in diameter. The small size allows the infiltration rate to be computed as the difference of the cumulative rainfall and cumulative runoff without having to route water through a large plot. Difference infiltrometers were deployed in an area burned by the 2010 Fourmile Canyon Fire near Boulder, Colorado, USA, and data were collected during the summer of 2011. The difference infiltrometer demonstrated the capability to capture different magnitudes of infiltration rates and temporal variability associated with convective (high intensity, short duration) and cyclonic (low intensity, long duration) rainstorms. Data from the difference infiltrometer were used to estimate saturated hydraulic conductivity of soil affected by the heat from a wildfire. The difference infiltrometer is portable and can be deployed in rugged, steep terrain and does not require the transport of water, as many rainfall simulators require, because it uses natural rainfall. It can be used to assess infiltration models, determine runoff coefficients, identify rainfall depth or rainfall intensity thresholds to initiate runoff, estimate parameters for infiltration models, and compare remediation treatments on disturbed landscapes. The difference infiltrometer can be linked with other types of soil monitoring equipment in long-term studies for detecting temporal and spatial variability at multiple time scales and in nested designs where it can be linked to hillslope and basin-scale runoff responses.

Thematic issue on soil water infiltration

Science.gov (United States)

Infiltration is the term applied to the process of water entry into the soil, generally by downward flow through all or part of the soil surface. Understanding of infiltration concept and processes has greatly improved, over the past 30 years, and new insights have been given into modeling of non-un...

Comparing the Goodness of Different Statistical Criteria for Evaluating the Soil Water Infiltration Models

Directory of Open Access Journals (Sweden)

S. Mirzaee

2016-02-01

interpretation of efficiency criteria (NSEI and its modified forms used to evaluate the models. Materials and Methods: The collection data of 145 point-data of measured infiltration of water into soil were used. The infiltration data were obtained by the Double Rings method in different soils of Iran having a wide range of soil characteristics. The study areas were located in Zanjan, Fars, Ardebil, Bushehr and Isfahan provinces. The soils of these regions are classified as Mollisols, Aridisols, Inceptisols and Entisols soil taxonomy orders. The land use of the study area consisted of wheat, barley, pasture and fallow land.The parameters of the models (i.e. Philip (18, Green and Ampt (3, SCS (23, Kostiakov (6, Horton (5, and Kostiakov and Lewis (11 models were determined, using the least square optimization method. All models were fitted to experimental infiltration data using an iterative nonlinear regression procedure, which finds the values of the fitting parameters that give the best fit between the model and the data. The fitting process was performed using the MatLab 7.7.0 (R2008b Software Package. Then, the ability of infiltration of water into soil models with the mean of coefficient of determination (R2, root mean square error (RMSE, efficiency criteria(NSEI and modified forms (such as NSEjI, NSESQRTI,NSElnI and NSEiI were determined and goodness of criteria was compared for the selection of the best model. Results and Discussion: The results showed the mean of RMSE for all soils cannot always be a suitable index for the evaluation of infiltration of water into soil models. A more valid comparison withNSEI, NSEjI, NSESQRTI, NSElnI indices indicated that these indices also cannot apparently distinguish among the infiltration models for the estimation of cumulative infiltration. These indices are sensitive to the large amount of data. The NSEiI index with giving more weight to infiltration data in shorter times was selected as the most appropriate index for comparing

Effects of stormwater infiltration on quality of groundwater beneath retention and detention basins

Science.gov (United States)

Fischer, D.; Charles, E.G.; Baehr, A.L.

2003-01-01

Infiltration of storm water through detention and retention basins may increase the risk of groundwater contamination, especially in areas where the soil is sandy and the water table shallow, and contaminants may not have a chance to degrade or sorb onto soil particles before reaching the saturated zone. Groundwater from 16 monitoring wells installed in basins in southern New Jersey was compared to the quality of shallow groundwater from 30 wells in areas of new-urban land use. Basin groundwater contained much lower levels of dissolved oxygen, which affected concentrations of major ions. Patterns of volatile organic compound and pesticide occurrence in basin groundwater reflected the land use in the drainage areas served by the basins, and differed from patterns in background samples, exhibiting a greater occurrence of petroleum hydrocarbons and certain pesticides. Dilution effects and volatilization likely decrease the concentration and detection frequency of certain compounds commonly found in background groundwater. High recharge rates in storm water basins may cause loading factors to be substantial even when constituent concentrations in infiltrating storm water are relatively low.

Gully incision rates on the bedrock of a large dip-slope landslide revealed by multi-period LiDAR DEMs

Science.gov (United States)

Chan, Y. C.; Hsieh, Y. C.

2017-12-01

Recent advances in airborne laser scanning (ALS) technology have provided a great opportunity for characterizing surface erosion through developing improved methods in multi-period DEM differencing and geomorphometry. This study uses three periods of ALS digital elevation model (DEM) data to analyze the short-term erosional features of the Tsaoling landslide triggered by the 1999 Chi-Chi earthquake in Taiwan. Two methods for calculating the bedrock incision rate, the equal-interval cross section selection method and the continuous swath profiles selection method, were used in the study after nearly ten years of gully incision following the earthquake-triggered dip-slope landslide. Multi-temporal gully incision rates were obtained using the continuous swath profiles selection method, which is considered a practical and convenient approach in terrain change studies. After error estimation and comparison of the multi-period ALS DEMs, the terrain change in different periods can be directly calculated, reducing time-consuming fieldwork such as installation of erosion pins and measurement of topographic cross sections on site. In this study, the gully bedrock incision rates ranged between 0.23 and 3.98 m/year, remarkably higher than the typical results from the previous studies. By comparing the DEM data, aerial photos, and precipitation records of this area, the effects of erosion could be observed from the retreat of the Chunqiu Cliff outline during August 2011 to September 2012. It was inferred that the change in the topographic elevation during 2011-2012 was mainly due to the torrential rain brought by Typhoon Soula, which occurred on 30 July 2012. The local gully incision rate in the lower part of the landslide surface was remarkably faster than that of the other regions, suggesting that the fast incision of the toe area possibly contributes to the occurrence of repeated landslides in the Tsaoling area.

Anomalous behaviors during infiltration into heterogeneous porous media

Science.gov (United States)

Aarão Reis, F. D. A.; Bolster, D.; Voller, V. R.

2018-03-01

Flow and transport in heterogeneous porous media often exhibit anomalous behavior. A physical analog example is the uni-directional infiltration of a viscous liquid into a horizontal oriented Hele-Shaw cell containing through thickness flow obstacles; a system designed to mimic a gravel/sand medium with impervious inclusions. When there are no obstacles present or the obstacles form a multi-repeating pattern, the change of the length of infiltration F with time t tends to follow a Fickian like scaling, F ∼t1/2 . In the presence of obstacle fields laid out as Sierpinski carpet fractals, infiltration is anomalous, i.e., F ∼ tn, n ≠ 1/2. Here, we study infiltration into such Hele-Shaw cells. First we investigate infiltration into a square cell containing one fractal carpet and make the observation that it is possible to generate both sub (n 1/2) diffusive behaviors within identical heterogeneity configurations. We show that this can be explained in terms of a scaling analysis developed from results of random-walk simulations in fractal obstacles; a result indicating that the nature of the domain boundary controls the exponent n of the resulting anomalous transport. Further, we investigate infiltration into a rectangular cell containing several repeats of a given Sierpinski carpet. At very early times, before the liquid encounters any obstacles, the infiltration is Fickian. When the liquid encounters the first (smallest scale) obstacle the infiltration sharply transitions to sub-diffusive. Subsequently, around the time where the liquid has sampled all of the heterogeneity length scales in the system, there is a rapid transition back to Fickian behavior. An explanation for this second transition is obtained by developing a simplified infiltration model based on the definition of a representative averaged hydraulic conductivity.

A case of alcoholic hepatitis demonstrating focal fatty infiltration of the liver on computed tomography

International Nuclear Information System (INIS)

Uesaka, Toshihiro; Kato, Masayoshi; Nagai, Tadayuki; Kametani, Tomio; Horigami, Tateyuki; Takimoto, Hiroaki; Tanino, Mikio

1985-01-01

Focal fatty infiltration of the liver is a newly recognized entity that may be confused with primary neoplasm or tumor metastasis on computed tomography. We report a 31-year-old woman with a history of chronic alcoholism. Physical examination revealed jaundice, marked hepatomegaly and ascites. Laboratory studies revealed mild elevation of bilirubin, AlP, GOT, γ-GTP and marked leukocytosis. Abdominal CT showed a large area of decreased density in the right lobe. The radionuclide scan demonstrated the area of diminished activity located in the central portion of the right lobe. Ultrasonography demonstrated high echoic mass shadows in the right lobe. The rapid disappearance of the low density area on CT was recognized. The liver biopsy specimen revealed fatty metamorphosis, alcoholic hyaline bodies, pericellular fibrosis and mild lobular disorganization. Focal fatty infiltration can mimic focal hepatic lesions and repeat CT scans are useful in diagnosis. (author)

Areally Extensive Surface Bedrock Exposures on Mars: Many Are Clastic Rocks, Not Lavas

Science.gov (United States)

Rogers, A. Deanne; Warner, Nicholas H.; Golombek, Matthew P.; Head, James W.; Cowart, Justin C.

2018-02-01

Areally extensive exposures of intact olivine/pyroxene-enriched rock, as well as feldspar-enriched rock, are found in isolated locations throughout the Martian highlands. The petrogenetic origin(s) of these rock units are not well understood, but some previous studies favored an effusive volcanic origin partly on the basis of distinctive composition and relatively high thermal inertia. Here we show that the regolith development, crater retention, and morphological characteristics for many of these "bedrock plains" are not consistent with competent lavas and reinterpret the high thermal inertia orbital signatures to represent friable materials that are more easily kept free of comminution products through eolian activity. Candidate origins include pyroclastic rocks, impact-generated materials, or detrital sedimentary rocks. Olivine/pyroxene enrichments in bedrock plains relative to surrounding materials could have potentially formed through deflation and preferential removal of plagioclase.

Characterizing Heterogeneity in Infiltration Rates During Managed Aquifer Recharge.

Science.gov (United States)

Mawer, Chloe; Parsekian, Andrew; Pidlisecky, Adam; Knight, Rosemary

2016-11-01

Infiltration rate is the key parameter that describes how water moves from the surface into a groundwater aquifer during managed aquifer recharge (MAR). Characterization of infiltration rate heterogeneity in space and time is valuable information for MAR system operation. In this study, we utilized fiber optic distributed temperature sensing (FO-DTS) observations and the phase shift of the diurnal temperature signal between two vertically co-located fiber optic cables to characterize infiltration rate spatially and temporally in a MAR basin. The FO-DTS measurements revealed spatial heterogeneity of infiltration rate: approximately 78% of the recharge water infiltrated through 50% of the pond bottom on average. We also introduced a metric for quantifying how the infiltration rate in a recharge pond changes over time, which enables FO-DTS to be used as a method for monitoring MAR and informing maintenance decisions. By monitoring this metric, we found high-spatial variability in how rapidly infiltration rate changed during the test period. We attributed this variability to biological pore clogging and found a relationship between high initial infiltration rate and the most rapid pore clogging. We found a strong relationship (R 2  = 0.8) between observed maximum infiltration rates and electrical resistivity measurements from electrical resistivity tomography data taken in the same basin when dry. This result shows that the combined acquisition of DTS and ERT data can improve the design and operation of a MAR pond significantly by providing the critical information needed about spatial variability in parameters controlling infiltration rates. © 2016, National Ground Water Association.

Mechanisms of water infiltration into conical hydrophobic nanopores.

Science.gov (United States)

Liu, Ling; Zhao, Jianbing; Yin, Chun-Yang; Culligan, Patricia J; Chen, Xi

2009-08-14

Fluid channels with inclined solid walls (e.g. cone- and slit-shaped pores) have wide and promising applications in micro- and nano-engineering and science. In this paper, we use molecular dynamics (MD) simulations to investigate the mechanisms of water infiltration (adsorption) into cone-shaped nanopores made of a hydrophobic graphene sheet. When the apex angle is relatively small, an external pressure is required to initiate infiltration and the pressure should keep increasing in order to further advance the water front inside the nanopore. By enlarging the apex angle, the pressure required for sustaining infiltration can be effectively lowered. When the apex angle is sufficiently large, under ambient condition water can spontaneously infiltrate to a certain depth of the nanopore, after which an external pressure is still required to infiltrate more water molecules. The unusual involvement of both spontaneous and pressure-assisted infiltration mechanisms in the case of blunt nanocones, as well as other unique nanofluid characteristics, is explained by the Young's relation enriched with the size effects of surface tension and contact angle in the nanoscale confinement.

Pituitary infiltration by non-Hodgkin's lymphoma: a case report

Directory of Open Access Journals (Sweden)

Aral Ferihan

2009-11-01

Full Text Available Abstract Introduction Pituitary adenomas represent the most frequently observed type of sellar masses; however, the presence of a rapidly growing sellar tumor, diabetes insipidus, ophthalmoplegia and headaches in an older patient strongly suggests metastasis to the pituitary. Since the anterior pituitary has a great reserve capacity, metastasis to the pituitary and pituitary involvement in lymphoma are usually asymptomatic. Whereas diabetes insipidus is the most frequent symptom, patients can present with headaches, ophthalmoplegia and bilateral hemianopsia. Case presentation A 70-year-old woman with no previous history of malignancy presented with headaches, right oculomotor nerve palsy and diabetes insipidus. As magnetic resonance imaging revealed a sellar mass involving the pituitary gland and infundibular stalk, which also extended into the right cavernous sinus and sphenoid sinus, the patient underwent an immediate transsphenoidal decompression surgery. Her prolactin was 102.4 ng/ml, whereas her gonadotropic hormone levels were low. A low level of urine osmolality after overnight water deprivation, along with normal plasma osmolality suggested diabetes insipidus. Histological examination revealed that the mass had been the infiltration of a high grade B-cell non-Hodgkin's lymphoma involving respiratory system epithelial cells. Paranasal sinus computed tomography scanning and magnetic resonance imaging of the thorax and abdomen were performed. Since magnetic resonance imaging did not reveal any abnormality, after paranasal sinus computed tomography was performed, we concluded that the primary lymphoma originated from the sphenoid sinus and infiltrated the pituitary. Chemotherapy and radiotherapy to the sellar area were planned, but the patient died and her family did not permit an autopsy. Conclusion Lymphoma infiltration to the pituitary is difficult to differentiate from pituitary adenoma, meningioma and other sellar lesions. To plan the

Effect of Ru/CGO versus Ni/CGO Co- Infiltration on the Performance and Stability of STN-Based SOFCs

DEFF Research Database (Denmark)

Ramos, Tania; Veltzé, Sune; Sudireddy, Bhaskar Reddy

2014-01-01

/CGO infiltrated cell reached ∼0.7 W cm–2 at 850 °C, 4% H2O/H2, whereas the Ni/CGO infiltrated cell reached ∼0.3 W cm–2, with the current morphologies and loadings. Operation at 0.125 A cm–2, 850 °C, feeding 50% H2O/H2 to the anode and air to the cathode, for a period >300 h, showed superior stability for the Ru....../CGO infiltrated cell, with ∼0.04 mV h–1 degradation rate, when compared to the Ni/CGO infiltrated cell (∼0.5 mV h–1). For the Ni/CGO case, the observed degradation has been tentatively linked to initial changes in the electrochemical active area and longterm detrimental interactions between components....

Catch crops impact on soil water infiltration in vineyards

Science.gov (United States)

Cerdà, Artemi; Bagarello, Vincenzo; Iovino, Massimo; Ferro, Vito; Keesstra, Saskia; Rodrigo-Comino, Jesús; García Diaz, Andrés; di Prima, Simone

2017-04-01

Bagarello, V., Castellini, M., Di Prima, S., & Iovino, M. (2014). Soil hydraulic properties determined by infiltration experiments and different heights of water pouring. Geoderma, 213, 492-501. Bagarello, V., Elrick, D. E., Iovino, M., & Sgroi, A. (2006). A laboratory analysis of falling head infiltration procedures for estimating the hydraulic conductivity of soils. Geoderma, 135, 322-334. Ben Slimane, A., Raclot, D., Evrard, O., Sanaa, M., Lefevre, I., & Le Bissonnais, Y. (2016). Relative contribution of Rill/Interrill and Gully/Channel erosion to small reservoir siltation in mediterranean environments. Land Degradation and Development, 27(3), 785-797. doi:10.1002/ldr.2387 Cerdà, A. (1996). Seasonal variability of infiltration rates under contrasting slope conditions in southeast spain. Geoderma, 69(3-4), 217-232. Cerdà, A. (1999). Seasonal and spatial variations in infiltration rates in badland surfaces under mediterranean climatic conditions. Water Resources Research, 35(1), 319-328. doi:10.1029/98WR01659 Cerdà, A. (2001). Effects of rock fragment cover on soil infiltration, interrill runoff and erosion. European Journal of Soil Science, 52(1), 59-68. doi:10.1046/j.1365-2389.2001.00354.x Cerdà, A., Morera, A. G., & Bodí, M. B. (2009). Soil and water losses from new citrus orchards growing on sloped soils in the western mediterranean basin. Earth Surface Processes and Landforms, 34(13), 1822-1830. doi:10.1002/esp.1889 di Prima, S., Lassabatère, L., Bagarello, V., Iovino, M., & Angulo-Jaramillo, R. (2016). Testing a new automated single ring infiltrometer for Beerkan infiltration experiments. Geoderma, 262, 20-34. Iovino, M., Castellini, M., Bagarello, V., & Giordano, G. (2016). Using static and dynamic indicators to evaluate soil physical quality in a sicilian area. Land Degradation and Development, 27(2), 200-210. doi:10.1002/ldr.2263 Laudicina, V. A., Novara, A., Barbera, V., Egli, M., & Badalucco, L. (2015). Long-term tillage and cropping system effects on

Impact of climate variations on Managed Aquifer Recharge infiltration basins.

Science.gov (United States)

Barquero, Felix; Stefan, Catalin

2017-04-01

KEYWORDS: Managed Aquifer Recharge, field scale infiltration unit, climatic conditions, numerical model Managed Aquifer Recharge (MAR) is a technique that is gaining more attention as a sustainable alternative for areas where water scarcity is increasing. Main concept relies on facilitating the vertical infiltration of a source of fresh water (river water, rainwater, reclaimed water, etc). The groundwater acts as storage of water for further use in the future, for example in times of water scarcity. In some MAR types the soil itself can be used even as a filter for the removal of specific organic and inorganic compounds. In order to promote the benefits of MAR in different zones of the globe with variable climate conditions, including the effects of climate change, a numerical model (HYDRUS 2D/3D) is being set up. Coupled with the model a field-scale rapid infiltration unit (4m x 5m x 1.5m) was constructed with the capacity to log different MAR key parameters in the soil (tension, water content, temperature and electrical conductivity) in space and time. These data will feed the model for its calibration using specific hydrogeological characteristics of the packing material and hydraulic characteristics of the infiltrated fluid. The unit is located in the city of Pirna (German), 200 m north from the Elbe River where the groundwater level varies seasonally between 6 and 9 m below the ground surface. Together with the field scale rapid infiltration unit, a set of multi-parametric sensors (measuring in time: water stage, electrical conductivity, dissolved oxygen and temperature) in six monitoring wells, located on the basin surroundings, were installed. The purpose of these sensors is to estimate, via tracer experiments, the time that the infiltrated water needed to reach the groundwater and the flow speed in which it travelled once it reached the saturated zone. Once calibrated, the model will be able to estimate the flow behaviour under variable climate conditions

Map of infiltration of the Paraíba do Sul basin using physical elements and precipitation

Directory of Open Access Journals (Sweden)

George de Paula Bernardes

2008-04-01

Full Text Available This paper presents a methodological approach to characterize the infiltrations conditions of a portion of Paraiba do Sul river basin (7,600 km2 using Geographic Information Systems tools. To each landscape feature (rock, structure, relief, soil, and land-use and to the spatial distribution of precipitation, an infiltration potential scale factor that ranges from higher influence (5 to lower influence (1 was applied considering its geographical position. The results showed that higher infiltration capacity areas are located in Serra da Bocaina associated to Serra do Mar relief in the Northeast region and Southeast region as well associated to gentle hills and sandstones along the Paraíba do Sul river. The creation of an Infiltration Map may contribute to the development of long-term territorial plans and water resource management plans in order to support future implementation of non-structural and structural measures at both regional and local scales.

Relative contributions of transient and steady state infiltration during ephemeral streamflow

Science.gov (United States)

Blasch, Kyle W.; Ferré, Ty P.A.; Hoffmann, John P.; Fleming, John B.

2006-01-01

Simulations of infiltration during three ephemeral streamflow events in a coarse‐grained alluvial channel overlying a less permeable basin‐fill layer were conducted to determine the relative contribution of transient infiltration at the onset of streamflow to cumulative infiltration for the event. Water content, temperature, and piezometric measurements from 2.5‐m vertical profiles within the alluvial sediments were used to constrain a variably saturated water flow and heat transport model. Simulated and measured transient infiltration rates at the onset of streamflow were about two to three orders of magnitude greater than steady state infiltration rates. The duration of simulated transient infiltration ranged from 1.8 to 20 hours, compared with steady state flow periods of 231 to 307 hours. Cumulative infiltration during the transient period represented 10 to 26% of the total cumulative infiltration, with an average contribution of approximately 18%. Cumulative infiltration error for the simulated streamflow events ranged from 9 to 25%. Cumulative infiltration error for typical streamflow events of about 8 hours in duration in is about 90%. This analysis indicates that when estimating total cumulative infiltration in coarse‐grained ephemeral stream channels, consideration of the transient infiltration at the onset of streamflow will improve predictions of the total volume of infiltration that may become groundwater recharge.

Effect of Fruits Waste in Biopore Infiltration Hole Toward The Effectiveness of Water Infiltration Rate on Baraya Campus Land of Hasanuddin University

Science.gov (United States)

Santosa, Slamet

2018-03-01

The infiltration of water into the soil decreases due to the transfer of soill function or the lack of soil biopores. This study aims to determine the effectiveness of the use of fruits waste toward the water infiltration rate. Observation of the water level decrease is done every 5 minutes interval. Observation of biopore water infiltration rate was done after fruits waste decomposed for 15 and 30 days. Result of standard water infiltration rate at the first of 5 minutes is 2.18 mm/min, then decreases at interval of 5 minutes on next time as the soil begins to saturate the water. Baraya campus soil observed in soil depths of 100cm has a dusty texture character, grayish brown color and clumping structure. Soil character indicates low porosity. While biopore water infiltration rate at the first of 5 minute interval is 6.61and 6.95 mm/min on banana waste; 5.55 and 6.61mm/min on papaya waste and 4.26 and 5.39 mm/min on mango waste. The effectiveness of water infiltration rate is 44.45% and 41.93% on banana; 44.61% and 30.09% on papaya and 15.79% and 28.36% on mango. Study concluded that banana waste causes the water infiltration rate most effective in biopore infiltration hole.

Comparison of mineral weathering and biomass nutrient uptake in two small forested watersheds underlain by quartzite bedrock, Catoctin Mountain, Maryland, USA

Science.gov (United States)

Rice, Karen; Price, Jason R.

2014-01-01

To quantify chemical weathering and biological uptake, mass-balance calculations were performed on two small forested watersheds located in the Blue Ridge Physiographic Province in north-central Maryland, USA. Both watersheds, Bear Branch (BB) and Fishing Creek Tributary (FCT), are underlain by relatively unreactive quartzite bedrock. Such unreactive bedrock and associated low chemical-weathering rates offer the opportunity to quantify biological processes operating within the watershed. Hydrologic and stream-water chemistry data were collected from the two watersheds for the 9-year period from June 1, 1990 to May 31, 1999. Of the two watersheds, FCT exhibited both higher chemical-weathering rates and biomass nutrient uptake rates, suggesting that forest biomass aggradation was limited by the rate of chemical weathering of the bedrock. Although the chemical-weathering rate in the FCT watershed was low relative to the global average, it masked the influence of biomass base-cation uptake on stream-water chemistry. Any differences in bedrock mineralogy between the two watersheds did not exert a significant influence on the overall weathering stoichiometry. The difference in chemical-weathering rates between the two watersheds is best explained by a larger proportion of reactive phyllitic layers within the bedrock of the FCT watershed. Although the stream gradient of BB is about two-times greater than that of FCT, its influence on chemical weathering appears to be negligible. The findings of this study support the biomass nutrient uptake stoichiometry of K1.0Mg1.1Ca0.97 previously determined for the study site. Investigations of the chemical weathering of relatively unreactive quartzite bedrock may provide insight into critical zone processes.

Brooks–Corey Modeling by One-Dimensional Vertical Infiltration Method

Directory of Open Access Journals (Sweden)

Xuguang Xing

2018-05-01

Full Text Available The laboratory methods used for the soil water retention curve (SWRC construction and parameter estimation is time-consuming. A vertical infiltration method was proposed to estimate parameters α and n and to further construct the SWRC. In the present study, the relationships describing the cumulative infiltration and infiltration rate with the depth of the wetting front were established, and simplified expressions for estimating α and n parameters were proposed. The one-dimensional vertical infiltration experiments of four soils were conducted to verify if the proposed method would accurately estimate α and n. The fitted values of α and n, obtained from the RETC software, were consistent with the calculated values obtained from the infiltration method. The comparison between the measured SWRCs obtained from the centrifuge method and the calculated SWRCs that were based on the infiltration method displayed small values of root mean square error (RMSE, mean absolute percentage error (MAPE, and mean absolute error. SWMS_2D-based simulations of cumulative infiltration, based on the calculated α and n, remained consistent with the measured values due to small RMSE and MAPE values. The experiments verified the proposed one-dimensional vertical infiltration method, which has applications in field hydraulic parameter estimation.

Investigation of radionuclide release from Solid Waste Disposal Area 3, Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Stueber, A.M.; Webster, D.A.; Munro, I.L.; Farrow, N.D.; Scott, T.G.

1981-08-01

Radionuclide release from Solid Waste Disposal Area (SWDA) 3 has been studied through the analysis of surface and ground waters from the local drainage areas. SWDA 3 is located in the Northwest Tributary drainage basin, a part of the White Oak Creek drainage; 90 Sr is the only radionuclide being discharged in solution in the main stream. Water-level measurements in wells around SWDA 3 suggest the presence of a ground-water divide beneath the southwestern end of the disposal area. Ground water below this area may be moving southwestward toward the Raccoon Creek drainage system. Strontium-90 activity has been detected in this watershed, discharging from a seep adjacent to a Raccoon Creek tributary stream about 640 m southwest of SWDA 3. It appears that 90 Sr is moving through ground-water flow to the northeast and to the southwest of SWDA 3 and that this direction of movement is related to bedrock structure. The trend of a line connecting the two seeps passes through the disposal area and is parallel to bedrock strike. Information from core-hole logs and televiewer logs suggests that 90 Sr in ground water may be moving through solution channels near the contact between units F and G of the Chickamauga Limestone. The apparent extent of migration of 90 Sr in bedrock has implications regarding potential underground radionuclide movement in Melton Valley

Management of white spots: resin infiltration technique and microabrasion

Directory of Open Access Journals (Sweden)

Jeong-Hye Son

2011-01-01

Full Text Available This case report compared the effectiveness of resin infiltration technique (Icon, DMG with microabrasion (Opalustre, Ultradent Products, Inc. in management of white spot lesions. It demonstrates that although neither microabrasion nor resin infiltration technique can remove white spot lesions completely, resin infiltration technique seems to be more effective than microabrasion. Therefore resin infiltration technique can be chosen preferentially for management of white spot lesions and caution should be taken for case selection.

The Natural Terrestrial Carbon Sequestration Potential of Rocky Mountain Soils Derived From Volcanic Bedrock

Science.gov (United States)

Yager, D. B.; Burchell, A.; Johnson, R. H.

2008-12-01

The possible economic and environmental ramifications of climate change have stimulated a range of atmospheric carbon mitigation actions, as well as, studies to understand and quantify potential carbon sinks. However, current carbon management strategies for reducing atmospheric emissions underestimate a critical component. Soils represent between 18 - 30% of the terrestrial carbon sink needed to prevent atmospheric doubling of CO2 by 2050 and a crucial element in mitigating climate change, natural terrestrial sequestration (NTS), is required. NTS includes all naturally occurring, cumulative, biologic and geologic processes that either remove CO2 from the atmosphere or prevent net CO2 emissions through photosynthesis and microbial fixation, soil formation, weathering and adsorption or chemical reactions involving principally alumino- ferromagnesium minerals, volcanic glass and clays. Additionally, NTS supports ecosystem services by improving soil productivity, moisture retention, water purification and reducing erosion. Thus, 'global climate triage' must include the protection of high NTS areas, purposeful enhancement of NTS processes and reclamation of disturbed and mined lands. To better understand NTS, we analyzed soil-cores from Colorado, Rocky Mountain Cordillera sites. North-facing, high-plains to alpine sites in non-wetland environments were selected to represent temperate soils that may be less susceptible to carbon pool declines due to global warming than soils in warmer regions. Undisturbed soils sampled have 2 to 6 times greater total organic soil carbon (TOSC) than global TOSC averages (4 - 5 Wt. %). Forest soils derived from weathering of intermediate to mafic volcanic bedrock have the highest C (34.15 Wt. %), C:N (43) and arylsulfatase (ave. 278, high 461 μg p-nitrophenol/g/h). Intermediate TOSC was identified in soils derived from Cretaceous shale (7.2 Wt. %) and Precambrian, felsic gneiss (6.2 Wt. %). Unreclaimed mine-sites have the lowest C (0

CT imaging spectrum of infiltrative renal diseases.

Science.gov (United States)

Ballard, David H; De Alba, Luis; Migliaro, Matias; Previgliano, Carlos H; Sangster, Guillermo P

2017-11-01

Most renal lesions replace the renal parenchyma as a focal space-occupying mass with borders distinguishing the mass from normal parenchyma. However, some renal lesions exhibit interstitial infiltration-a process that permeates the renal parenchyma by using the normal renal architecture for growth. These infiltrative lesions frequently show nonspecific patterns that lead to little or no contour deformity and have ill-defined borders on CT, making detection and diagnosis challenging. The purpose of this pictorial essay is to describe the CT imaging findings of various conditions that may manifest as infiltrative renal lesions.

Model for solid oxide fuel cell cathodes prepared by infiltration

DEFF Research Database (Denmark)

Samson, Alfred Junio; Søgaard, Martin; Hendriksen, Peter Vang

2017-01-01

A 1-dimensional model of a cathode has been developed in order to understand and predict the performance of cathodes prepared by infiltration of La0.6Sr0.4Co1.05O3-δ (LSC) into porous backbones of Ce0.9Gd0.1O1.95 (CGO). The model accounts for the mixed ionic and electronic conductivity of LSC......, ionic conductivity of CGO, gas transport in the porous cathode, and the oxygen reduction reaction at the surface of percolated LSC. Geometrical variations are applied to reflect a changing microstructure of LSC under varying firing temperatures. Using microstructural parameters obtained from detailed...... scanning electron microscopy and simulations of the measured polarization resistances, an expression for the area specific resistance (rp) associated with the oxygen exchange on the surface of the infiltrated LSC particles was extracted and compared with literature values. A series of microstructural...

Hillslope response to sprinkling and natural rainfall using velocity and celerity estimates in a slate-bedrock catchment

Science.gov (United States)

Scaini, Anna; Hissler, Christophe; Fenicia, Fabrizio; Juilleret, Jérôme; Iffly, Jean François; Pfister, Laurent; Beven, Keith

2018-03-01

Subsurface flow is often recognized as a dominant runoff generation process. However, observing subsurface properties, and understanding how they control flow pathways, remains challenging. This paper investigates how surface slope and bedrock cleavage control subsurface flow pathways in a slate bedrock headwater catchment in Luxembourg, characterised by a double-peak streamflow response. We use a range of experimental techniques, including field observations of soil and bedrock characteristics, and a sprinkling experiment at a site located 40 m upslope from the stream channel. The sprinkling experiment uses Br- as a tracer, which is measured at a well downslope from the plot and at various locations along the stream, together with well and stream hydrometric responses. The sprinkling experiment is used to estimate velocities and celerities, which in turn are used to infer flow pathways. Our results indicate that the single or first peak of double-peak events is rainfall-driven (controlled by rainfall) while the second peak is storage-driven (controlled by storage). The comparison between velocity and celerity estimates suggests a fast flowpath component connecting the hillslope to the stream, but velocity information was too scarce to fully support such a hypothesis. In addition, different estimates of celerities suggest a seasonal influence of both rainfall intensity rate and residual water storage on the celerity responses at the hillslope scale. At the catchment outlet, the estimated of the total mass of Br- recovered in the stream was about 2.5% of the application. Further downstream, the estimate mass of Br- was about 4.0% of the application. This demonstrates that flowpaths do not appear to align with the slope gradient. In contrast, they appear to follow the strike of the bedrock cleavage. Our results have expanded our understanding of the importance of the subsurface, in particular the underlying bedrock systems, and the importance of cleavage orientation

Reactive Melt Infiltration Of Silicon Into Porous Carbon

Science.gov (United States)

Behrendt, Donald R.; Singh, Mrityunjay

1994-01-01

Report describes study of synthesis of silicon carbide and related ceramics by reactive melt infiltration of silicon and silicon/molybdenum alloys into porous carbon preforms. Reactive melt infiltration has potential for making components in nearly net shape, performed in less time and at lower temperature. Object of study to determine effect of initial pore volume fraction, pore size, and infiltration material on quality of resultant product.

Flow and sorption controls of groundwater arsenic in individual boreholes from bedrock aquifers in central Maine, USA

Energy Technology Data Exchange (ETDEWEB)

Yang, Qiang [Lamont-Doherty Earth Observatory of Columbia University, 61 Route 9 W, Palisades, NY 10964 (United States); School of Earth and Environmental Sciences, Queens College and Graduate Center, City University of New York, 65-30 Kissena Blvd., Flushing, NY 11367 (United States); Culbertson, Charles W.; Nielsen, Martha G.; Schalk, Charles W. [U.S. Geological Survey, Maine Water Science Center, 196 Whitten Road, Augusta, ME 04330 (United States); Johnson, Carole D. [U.S. Geological Survey, Branch of Geophysics, 11 Sherman Place, Unit 5015, University of Connecticut, Storrs, CT 06269 (United States); Marvinney, Robert G. [Maine Geological Survey, 93 State House Station, Augusta, ME 04333 (United States); Stute, Martin [Lamont-Doherty Earth Observatory of Columbia University, 61 Route 9 W, Palisades, NY 10964 (United States); Zheng, Yan, E-mail: yan.zheng@qc.cuny.edu [Lamont-Doherty Earth Observatory of Columbia University, 61 Route 9 W, Palisades, NY 10964 (United States); School of Earth and Environmental Sciences, Queens College and Graduate Center, City University of New York, 65-30 Kissena Blvd., Flushing, NY 11367 (United States)

2015-02-01

To understand the hydrogeochemical processes regulating well water arsenic (As) evolution in fractured bedrock aquifers, three domestic wells with [As] up to 478 μg/L are investigated in central Maine. Geophysical logging reveals that fractures near the borehole bottom contribute 70–100% of flow. Borehole and fracture water samples from various depths show significant proportions of As (up to 69%) and Fe (93–99%) in particulates (> 0.45 μm). These particulates and those settled after a 16-day batch experiment contain 560–13,000 mg/kg of As and 14–35% weight/weight of Fe. As/Fe ratios (2.5–20 mmol/mol) and As partitioning ratios (adsorbed/dissolved [As], 20,000–100,000 L/kg) suggest that As is sorbed onto amorphous hydrous ferric oxides. Newly drilled cores also show enrichment of As (up to 1300 mg/kg) sorbed onto secondary iron minerals on the fracture surfaces. Pumping at high flow rates induces large decreases in particulate As and Fe, a moderate increase in dissolved [As] and As(III)/As ratio, while little change in major ion chemistry. The δD and δ{sup 18}O are similar for the borehole and fracture waters, suggesting a same source of recharge from atmospheric precipitation. Results support a conceptual model invoking flow and sorption controls on groundwater [As] in fractured bedrock aquifers whereby oxygen infiltration promotes the oxidation of As-bearing sulfides at shallower depths in the oxic portion of the flow path releasing As and Fe; followed by Fe oxidation to form Fe oxyhydroxide particulates, which are transported in fractures and sorb As along the flow path until intercepted by boreholes. In the anoxic portions of the flow path, reductive dissolution of As-sorbed iron particulates could re-mobilize As. For exposure assessment, we recommend sampling of groundwater without filtration to obtain total As concentration in groundwater. - Highlights: • Most Fe and some As exist as particulates in the tested borehole and fracture water. �

Bedrock geologic map of parts of the Eden, Albany, Lowell, and Irasburg quadrangles, Vermont

Data.gov (United States)

Vermont Center for Geographic Information — Digital Data from VG09-4 (Digitized draft of VG97-5): Kim, J., 2009, Bedrock geologic map of parts of the Eden, Albany, Lowell, and Irasburg quadrangles, VGS...

Modeling a ponded infiltration experiment at Yucca Mountain, NV

International Nuclear Information System (INIS)

Hudson, D.B.; Guertal, W.R.; Flint, A.L.

1994-01-01

Yucca Mountain, Nevada is being evaluated as a potential site for a geologic repository for high level radioactive waste. As part of the site characterization activities at Yucca Mountain, a field-scale ponded infiltration experiment was done to help characterize the hydraulic and infiltration properties of a layered dessert alluvium deposit. Calcium carbonate accumulation and cementation, heterogeneous layered profiles, high evapotranspiration, low precipitation, and rocky soil make the surface difficult to characterize.The effects of the strong morphological horizonation on the infiltration processes, the suitability of measured hydraulic properties, and the usefulness of ponded infiltration experiments in site characterization work were of interest. One-dimensional and two-dimensional radial flow numerical models were used to help interpret the results of the ponding experiment. The objective of this study was to evaluate the results of a ponded infiltration experiment done around borehole UE25 UZN number-sign 85 (N85) at Yucca Mountain, NV. The effects of morphological horizons on the infiltration processes, lateral flow, and measured soil hydaulic properties were studied. The evaluation was done by numerically modeling the results of a field ponded infiltration experiment. A comparison the experimental results and the modeled results was used to qualitatively indicate the degree to which infiltration processes and the hydaulic properties are understood. Results of the field characterization, soil characterization, borehole geophysics, and the ponding experiment are presented in a companion paper

The effect of trees on preferential flow and soil infiltrability in an agroforestry parkland in semiarid Burkina Faso.

Science.gov (United States)

Bargués Tobella, A; Reese, H; Almaw, A; Bayala, J; Malmer, A; Laudon, H; Ilstedt, U

2014-04-01

Water scarcity constrains the livelihoods of millions of people in tropical drylands. Tree planting in these environments is generally discouraged due to the large water consumption by trees, but this view may neglect their potential positive impacts on water availability. The effect of trees on soil hydraulic properties linked to groundwater recharge is poorly understood. In this study, we performed 18 rainfall simulations and tracer experiments in an agroforestry parkland in Burkina Faso to investigate the effect of trees and associated termite mounds on soil infiltrability and preferential flow. The sampling points were distributed in transects each consisting of three positions: (i) under a single tree, (ii) in the middle of an open area, and (iii) under a tree associated with a termite mound. The degree of preferential flow was quantified through parameters based on the dye infiltration patterns, which were analyzed using image analysis of photographs. Our results show that the degree of preferential flow was highest under trees associated with termite mounds, intermediate under single trees, and minimal in the open areas. Tree density also had an influence on the degree of preferential flow, with small open areas having more preferential flow than large ones. Soil infiltrability was higher under single trees than in the open areas or under trees associated with a termite mound. The findings from this study demonstrate that trees have a positive impact on soil hydraulic properties influencing groundwater recharge, and thus such effects must be considered when evaluating the impact of trees on water resources in drylands. Trees in dryland landscapes increase soil infiltrability and preferential flow Termite mounds in association with trees further enhance preferential flow.

Durability and Performance of High Performance Infiltration Cathodes

DEFF Research Database (Denmark)

Samson, Alfred Junio; Søgaard, Martin; Hjalmarsson, Per

2013-01-01

The performance and durability of solid oxide fuel cell (SOFC) cathodes consisting of a porous Ce0.9Gd0.1O1.95 (CGO) infiltrated with nitrates corresponding to the nominal compositions La0.6Sr0.4Co1.05O3-δ (LSC), LaCoO3-δ (LC), and Co3O4 are discussed. At 600°C, the polarization resistance, Rp......, varied as: LSC (0.062Ωcm2)cathode was found to depend on the infiltrate firing temperature and is suggested to originate...... of the infiltrate but also from a better surface exchange property. A 450h test of an LSC-infiltrated CGO cathode showed an Rp with final degradation rate of only 11mΩcm2kh-1. An SOFC with an LSC-infiltrated CGO cathode tested for 1,500h at 700°C and 0.5Acm-2 (60% fuel, 20% air utilization) revealed no measurable...

Final disposal of spent nuclear fuel in Finnish bedrock. Olkiluoto site report

Energy Technology Data Exchange (ETDEWEB)

Anttila, P. [Fortum Engineering Oy, Vantaa (Finland); Ahokas, H. [Fintact Oy, Helsinki (Finland); Front, K. [VTT Communication and Infrastructure, Espoo (Finland)] [and others

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Olkiluoto. The bedrock of the Olkiluoto site consists of Svecofennian metasediments and platonic rocks, 1800-1900 million years in age. Migmatitic mica gneiss is the most abundant rock type, and is intruded by foliated tonalites and granodiorites and massive coarse-grained granites and pegmatites. Five successive plastic deformation phases have been defined. In total, 30 bedrock structures (R-structures) have been modelled at the site. Most of these represent steeply dipping fracture zones, but several sub-horizontal zones, gently dipping to the SE, have also been identified. The rock mass between the fracture zones represents what is termed `intact rock`, which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 3 x 10{sup -7} m{sup 2}/s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval, is 8 x 10{sup -13} m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater chemistry reflects the

Final disposal of spent nuclear fuel in Finnish bedrock. Olkiluoto site report

International Nuclear Information System (INIS)

Anttila, P.; Ahokas, H.; Front, K.

1999-06-01

Posiva Oy is studying the Finnish bedrock for the geological disposal of spent nuclear fuel. The study is based on the site selection research programme started originally in 1983. The programme is in accordance with the decision in principle by the Council of State in 1983 and aims at the selection of one site in 2000. Four sites, Haestholmen in Loviisa, Kivetty in Aeaenekoski, Olkiluoto in Eurajoki and Romuvaara in Kuhmo, have been studied in detail. This report summarises the results of the site investigations carried out at Olkiluoto. The bedrock of the Olkiluoto site consists of Svecofennian metasediments and platonic rocks, 1800-1900 million years in age. Migmatitic mica gneiss is the most abundant rock type, and is intruded by foliated tonalites and granodiorites and massive coarse-grained granites and pegmatites. Five successive plastic deformation phases have been defined. In total, 30 bedrock structures (R-structures) have been modelled at the site. Most of these represent steeply dipping fracture zones, but several sub-horizontal zones, gently dipping to the SE, have also been identified. The rock mass between the fracture zones represents what is termed 'intact rock', which is typically hard, unweathered and sparsely fractured. The R-structures are generally hydraulically more conductive than the intact rock and their mean transmissivity is 3 x 10 -7 m 2 /s. The corresponding mean of the hydraulic conductivity values for the intact rock measured using a 2 m packer interval, is 8 x 10 -13 m/s, if a lognormal distribution for all measured values is assumed. A clear decrease in hydraulic conductivity with depth has been found for the intact rock, and there seems to be a parallel decrease in the transmissivity of structures. In addition, the hydraulically conductive fractures seem to be more frequent and their transmissivities higher in the uppermost 100 - 200 m of the bedrock than at greater depths. The groundwater chemistry reflects the postglacial

Demonstration of the infiltration of the carcinoma of uterine cervix by using 111In-bleomycin scintigraphy

International Nuclear Information System (INIS)

Kida, Toshiyuki; Ikeda, Masanori

1978-01-01

We studied on scintigraphy for demonstration of primary site and infiltrating area of carcinoma of uterine cervix by using 111 In-BLM, which is drawing attention as one of the tumor-imaging agents. In 17 cases (77%) out of 22 cases of the carcinoma of uterine cervix, this scintigraphy demonstrated the primary site and the extent of infiltration into parametrium with distinctive positive images. Thus, this radiopharmaceutical was found to be of great use for determining the treatment of the carcinoma of uterine cervix. (author)

Field evidence for control of quarrying by rock bridges in jointed bedrock

Science.gov (United States)

Hooyer, T. S.; Cohen, D. O.; Iverson, N. R.

2011-12-01

Quarrying is generally thought to be the most important mechanism by which glaciers erode bedrock. In quarrying models it is assumed that slow, subcritical, growth of pre-existing cracks rate-limits the process and occurs where there are large stress differences in the bed, such as near rock bumps where ice separates from the bed to form water-filled cavities. Owing to the direction of principal stresses in rocks associated with sliding and resultant cavity formation, models predict that quarrying will occur along cracks oriented perpendicular to the ice flow direction or parallel to zones of ice-bed contact. Preglacial cracks in rocks will tend to propagate mainly downward, and in sedimentary or some metamorphic rocks will merge with bedding planes, thereby helping to isolate rock blocks for dislodgement. In contrast to these model assumptions, new measurements of quarried surface orientations in the deglaciated forefield of nine glaciers in Switzerland and Canada indicate a strong correlation between orientations of pre-existing joints and quarried bedrock surfaces, independent of ice flow direction or ice-water contact lines. The strong correlation persists across all rock types, and rocks devoid of major joints lack quarried surfaces. We propose a new conceptual model of quarrying that idealizes the bedrock as a series of blocks separated by discontinuous preglacial joints containing intact rock bridges. Bridges concentrate stress differences caused by normal and shear forces acting at the rock surface. Failure of bridges is caused by slow subcritical crack growth enhanced by water pressure fluctuations. To lend credibility to this new model, we show field evidence of failed rock bridges in quarried surfaces and of rib marks on plumose structures that we interpret as arrest fracture fronts due to transient subglacial water-pressure fluctuations.

Hydrogeological Properties of the Rocks in Adansi Mining Area ...

African Journals Online (AJOL)

Michael

2016-06-01

Jun 1, 2016 ... zones and in fractures of the bedrocks, as well as lack of detailed .... after which the second stage of recovery of 3 hours followed. During .... In areas with lower hydraulic .... He is a member of the International. Association of ...

General hydroisotopic study of direct infiltration and evaporation process through the unsaturated zone in Damascus oasis, Syrian Arab Republic

International Nuclear Information System (INIS)

Abou Zakhem, B.; Hafez, R.

2001-01-01

Damascus oasis plays an important economical and environmental role in the city life because it presents the surrounding green places and the groundwater is the main sources for irrigation. In this study we will focus on the unsaturated zone in Damascus oasis. Environmental isotopes as 18 O, 2 H and 3 H are considered one of the most important techniques that are used in unsaturated zone study in order to study the water movement mechanism, estimate the effective velocity, the rate and spatial variations of the direct infiltration through this zone.The Deuterium profile allow to estimate the direct evaporation rate, and it is observed that the evaporation in the eastern part of the studied area is 5-6.5 mm/y. The Tritium peak of profile that is belonging to the atmospheric nuclear tests at the beginning of the sixties indicates the effective infiltration velocity of 27.8 mm/y. The effective porosity was estimated about 6.5% and the permeability parameter is 0.6*10 -10 m/s. The direct infiltration rate was estimated by the chemical Chloride balance in the studied profiles in addition to their spatial distribution where it was distinguished between the eastern area where the direct infiltration is less than 2 mm/y characterized by very fine clay soils and western area where the direct infiltration rate is more than 2 mm/y with sandy soils. It is thought that the lower part of the unsaturated zone indicated the direct infiltration rate about 3.5 mm/y, under more wet climatic conditions where the rainfall was about 423 mm/y, this wet period was extended from about 432 y to more than 760y ago.The Nitrate concentration variation with depth indicated that unsaturated zone play important role as purification zone, and the groundwater which has more than 5 m depth is prevented from pollution, whereas the groundwater that has less than 5 m depth is more prone to pollution by high concentration of Nitrates. (author)

Prediction of the existence or fine-grained granite dykes in the Simpevarp area; Prediktering av foerekomst av finkorniga granitgaangar i Simpevarpsomraadet

Energy Technology Data Exchange (ETDEWEB)

Mattsson, Haakan; Triumf, Carl-Axel [GeoVista AB, Luleaa (Sweden); Wahlgren, Carl-Henric [Geological Survey of Sweden, Uppsala (Sweden)

2002-11-01

Fine-grained granite dykes associated with a high fracture frequency occur in the bedrock of the Simpevarp region. In order to avoid problems in a future storage for nuclear waste it is important to find methods to detect areas where the dykes occur frequently. The aim of this project is to test the possibility to use airborne gamma ray spectrometry in the Simpevarp region to distinguish between different areas of the bedrock containing a varying frequency of fine-grained granite dykes. Investigations were also made to test if and how plastic deformation and a thin cover of moss affect the radiometric signature of the rocks. Ground measurements with a gamma ray spectrometer were performed on the islands of Aespoe, Aevroe and at the Simpevarp peninsula on different kinds of Smaaland granite with varying frequencies of fine-grained granite dykes. Reference measurements were performed on rocks without granite dykes. The bedrock at the measurement sites was geologically characterized in connection to the measurements. Air borne radiometric data (uranium, potassium and thorium) measured by the Geological Survey of Sweden in 1986 (flight altitude 30 m, point distance 40 m, line spacing 200 m) was compared to the existing bedrock map of the area and also to existing observation sites of fine-grained granite dykes. The ground measurements with gamma ray spectrometer clearly indicate that the fine-grained granite dykes have a specific radiometric signature compared to the granite-granodiorite at Aevroe and the quartzmonzodiorite-granodiorite at Aespoe. The main difference between the dykes and the other investigated rocks is seen in the thorium content, which is typically 3-5 times greater in the fine grained granite dykes. A thin cover of moss does not seem to significantly affect the radiometric signal of the bedrock, and neither does plastic deformation. However, the number of measurements on deformed and on covered rocks is low. The radiometric anomaly pattern shown in

Overview of chemical vapor infiltration

Energy Technology Data Exchange (ETDEWEB)

Besmann, T.M.; Stinton, D.P.; Lowden, R.A.

1993-06-01

Chemical vapor infiltration (CVI) is developing into a commercially important method for the fabrication of continuous filament ceramic composites. Current efforts are focused on the development of an improved understanding of the various processes in CVI and its modeling. New approaches to CVI are being explored, including pressure pulse infiltration and microwave heating. Material development is also proceeding with emphasis on improving the oxidation resistance of the interfacial layer between the fiber and matrix. This paper briefly reviews these subjects, indicating the current state of the science and technology.

DECIPHERING THE FINEST IMPRINT OF GLACIAL EROSION: OBJECTIVE ANALYSIS OF STRIAE PATTERNS ON BEDROCK

Directory of Open Access Journals (Sweden)