WorldWideScience

Sample records for bed biomass steam

  1. Application of CaO-Based Bed Material for Dual Fluidized Bed Steam Biomass Gasification

    Science.gov (United States)

    Koppatz, S.; Pfeifer, C.; Kreuzeder, A.; Soukup, G.; Hofbauer, H.

    Gasification of biomass is a suitable option for decentralized energy supply based on renewable sources in the range of up to 50 MW fuel input. The paper presents the dual fluidized bed (DFB) steam gasification process, which is applied to generate high quality and nitrogen-free product gas. Essential part of the DFB process is the bed material used in the fluidized reactors, which has significant impact on the product gas quality. By the use of catalytically active bed materials the performance of the overall process is increased, since the bed material favors reactions of the steam gasification. In particular, tar reforming reactions are favored. Within the paper, the pilot plant based on the DFB process with 100kW fuel input at Vienna University of Technology, Austria is presented. Actual investigations with focus on CaO-based bed materials (limestone) as well as with natural olivine as bed material were carried out at the pilot plant. The application of CaO-based bed material shows mainly decreased tar content in the product gas in contrast to experiments with olivine as bed material. The paper presents the results of steam gasification experiments with limestone and olivine, whereby the product gas composition as well as the tar content and the tar composition are outlined.

  2. Experimental and predicted approaches for biomass gasification with enriched air-steam in a fluidised bed.

    Science.gov (United States)

    Fu, Qirang; Huang, Yaji; Niu, Miaomiao; Yang, Gaoqiang; Shao, Zhiwei

    2014-10-01

    Thermo-chemical gasification of sawdust refuse-derived fuel was performed on a bench-scale fluidised bed gasifier with enriched air and steam as fluidising and oxidising agents. Dolomite as a natural mineral catalyst was used as bed material to reform tars and hydrocarbons. A series of experiments were carried out under typical operating conditions for gasification, as reported in the article. A modified equilibrium model, based on equilibrium constants, was developed to predict the gasification process. The sensitivity analysis of operating parameters, such as the fluidisation velocity, oxygen percentage of the enriched air and steam to biomass ratios on the produced gas composition, lower heating value, carbon conversion and cold gas efficiency was investigated. The results showed that the predicted syngas composition was in better agreement with the experimental data compared with the original equilibrium model. The higher fluidisation velocity enhanced gas-solid mixing, heat and mass transfers, and carbon fines elutriation, simultaneously. With the increase of oxygen percentage from 21% to 45%, the lower heating value of syngas increased from 5.52 MJ m(-3) to 7.75 MJ m(-3) and cold gas efficiency from 49.09% to 61.39%. The introduction of steam improved gas quality, but a higher steam to biomass ratio could decrease carbon conversion and gasification efficiency owing to a low steam temperature. The optimal value of steam to biomass ratio in this work was 1.0.

  3. Effects of gasifying conditions and bed materials on fluidized bed steam gasification of wood biomass.

    Science.gov (United States)

    Weerachanchai, Piyarat; Horio, Masayuki; Tangsathitkulchai, Chaiyot

    2009-02-01

    The effect of steam gasification conditions on products properties was investigated in a bubbling fluidized bed reactor, using larch wood as the starting material. For bed material effect, calcined limestone and calcined waste concrete gave high content of H(2) and CO(2), while silica sand provided the high content of CO. At 650 degrees C, calcined limestone proved to be most effective for tar adsorption and showed high ability to adsorb CO(2) in bed. At 750 degrees C it could not capture CO(2) but still gave the highest cold gas efficiency (% LHV) of 79.61%. Steam gasification gave higher amount of gas product and higher H(2)/CO ratio than those obtained with N(2) pyrolysis. The combined use of calcined limestone and calcined waste concrete with equal proportion contributed relatively the same gas composition, gas yield and cold gas efficiency as those of calcined limestone, but showed less attrition, sintering, and agglomeration propensities similar to the use of calcined waste concrete alone.

  4. Performance of a pilot-scale, steam-blown, pressurized fluidized bed biomass gasifier

    Science.gov (United States)

    Sweeney, Daniel Joseph

    With the discovery of vast fossil resources, and the subsequent development of the fossil fuel and petrochemical industry, the role of biomass-based products has declined. However, concerns about the finite and decreasing amount of fossil and mineral resources, in addition to health and climate impacts of fossil resource use, have elevated interest in innovative methods for converting renewable biomass resources into products that fit our modern lifestyle. Thermal conversion through gasification is an appealing method for utilizing biomass due to its operability using a wide variety of feedstocks at a wide range of scales, the product has a variety of uses (e.g., transportation fuel production, electricity production, chemicals synthesis), and in many cases, results in significantly lower greenhouse gas emissions. In spite of the advantages of gasification, several technical hurdles have hindered its commercial development. A number of studies have focused on laboratory-scale and atmospheric biomass gasification. However, few studies have reported on pilot-scale, woody biomass gasification under pressurized conditions. The purpose of this research is an assessment of the performance of a pilot-scale, steam-blown, pressurized fluidized bed biomass gasifier. The 200 kWth fluidized bed gasifier is capable of operation using solid feedstocks at feedrates up to 65 lb/hr, bed temperatures up to 1600°F, and pressures up to 8 atm. Gasifier performance was assessed under various temperatures, pressure, and feedstock (untreated woody biomass, dark and medium torrefied biomass) conditions by measuring product gas yield and composition, residue (e.g., tar and char) production, and mass and energy conversion efficiencies. Elevated temperature and pressure, and feedstock pretreatment were shown to have a significant influence on gasifier operability, tar production, carbon conversion, and process efficiency. High-pressure and temperature gasification of dark torrefied biomass

  5. Simulation of biomass-steam gasification in fluidized bed reactors: Model setup, comparisons and preliminary predictions.

    Science.gov (United States)

    Yan, Linbo; Lim, C Jim; Yue, Guangxi; He, Boshu; Grace, John R

    2016-12-01

    A user-defined solver integrating the solid-gas surface reactions and the multi-phase particle-in-cell (MP-PIC) approach is built based on the OpenFOAM software. The solver is tested against experiments. Then, biomass-steam gasification in a dual fluidized bed (DFB) gasifier is preliminarily predicted. It is found that the predictions agree well with the experimental results. The bed material circulation loop in the DFB can form automatically and the bed height is about 1m. The voidage gradually increases along the height of the bed zone in the bubbling fluidized bed (BFB) of the DFB. The U-bend and cyclone can separate the syngas in the BFB and the flue gas in the circulating fluidized bed. The concentration of the gasification products is relatively higher in the conical transition section, and the dry and nitrogen-free syngas at the BFB outlet is predicted to be composed of 55% H2, 20% CO, 20% CO2 and 5% CH4.

  6. Hydrogen-rich gas production by steam gasification of char from biomass fast pyrolysis in a fixed-bed reactor: influence of temperature and steam on hydrogen yield and syngas composition.

    Science.gov (United States)

    Yan, Feng; Luo, Si-yi; Hu, Zhi-quan; Xiao, Bo; Cheng, Gong

    2010-07-01

    Steam gasification experiments of biomass char were carried out in a fixed-bed reactor. The experiments were completed at bed temperature of 600-850 degrees C, a steam flow rate of 0-0.357 g/min/g of biomass char, and a reaction time of 15min. The aim of this study is to determine the effects of bed temperature and steam flow rate on syngas yield and its compositions. The results showed that both high gasification temperature and introduction of proper steam led to higher yield of dry gas and higher carbon conversion efficiency. However, excessive steam reduced gas yield and carbon conversion efficiency. The maximum dry gas yield was obtained at the gasification temperature of 850 degrees C and steam flow rate of 0.165 g/min/g biomass char.

  7. Modeling and simulation of biomass air-steam gasification in a fluidized bed

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    By considering the features of fluidized-bed reactors and the kinetic mechanism of biomass gasification,a steady-state,isothermal,one-dimensional and twophase mathematical model of biomass gasification kinetics in bubbling fluidized beds was developed.The model assumes the existence of two phases - a bubble and an emulsion phase - with chemical reactions occurring in both phases.The axial gas dispersion in the two phases is accounted for and the pyrolysis of biomass is taken to be instantaneous.The char and gas species CO,CO2,H2,H2O,CH4 and 8 chemical reactions are included in the model.The mathematical model belongs to a typical boundary value problem of ordinary differential equations and its solution is obtained by a Matlab program.Utilizing wood powder as the feedstock,the calculated data show satisfactory agreement with experimental results and proves the effectiveness and reliability of the model.

  8. Dual Fluidized Bed Biomass Gasification

    Energy Technology Data Exchange (ETDEWEB)

    None

    2005-09-30

    The dual fluidized bed reactor is a recirculating system in which one half of the unit operates as a steam pyrolysis device for biomass. The pyrolysis occurs by introducing biomass and steam to a hot fluidized bed of inert material such as coarse sand. Syngas is produced during the pyrolysis and exits the top of the reactor with the steam. A crossover arm, fed by gravity, moves sand and char from the pyrolyzer to the second fluidized bed. This sand bed uses blown air to combust the char. The exit stream from this side of the reactor is carbon dioxide, water and ash. There is a second gravity fed crossover arm to return sand to the pyrolysis side. The recirculating action of the sand and the char is the key to the operation of the dual fluidized bed reactor. The objective of the project was to design and construct a dual fluidized bed prototype reactor from literature information and in discussion with established experts in the field. That would be appropriate in scale and operation to measure the relative performance of the gasification of biomass and low ranked coals to produce a high quality synthesis gas with no dilution from nitrogen or combustion products.

  9. Steam gasification of wood biomass in a fluidized biocatalytic system bed gasifier: A model development and validation using experiment and Boubaker Polynomials Expansion Scheme BPES

    Directory of Open Access Journals (Sweden)

    Luigi Vecchione

    2015-07-01

    Full Text Available One of the most important issues in biomass biocatalytic gasification is the correct prediction of gasification products, with particular attention to the Topping Atmosphere Residues (TARs. In this work, performedwithin the European 7FP UNIfHY project, we develops and validate experimentally a model which is able of predicting the outputs,including TARs, of a steam-fluidized bed biomass gasifier. Pine wood was chosen as biomass feedstock: the products obtained in pyrolysis tests are the relevant model input. Hydrodynamics and chemical properties of the reacting system are considered: the hydrodynamic approach is based on the two phase theory of fluidization, meanwhile the chemical model is based on the kinetic equations for the heterogeneous and homogenous reactions. The derived differentials equations for the gasifier at steady state were implemented MATLAB. Solution was consecutively carried out using the Boubaker Polynomials Expansion Scheme by varying steam/biomass ratio (0.5-1 and operating temperature (750-850°C.The comparison between models and experimental results showed that the model is able of predicting gas mole fractions and production rate including most of the representative TARs compounds

  10. Biomass gasification and in-bed contaminants removal: performance of iron enriched olivine and bauxite in a process of steam/O2 gasification.

    Science.gov (United States)

    Barisano, D; Freda, C; Nanna, F; Fanelli, E; Villone, A

    2012-08-01

    A modified Olivine, enriched in iron content (10% Fe/Olivine), and a natural bauxite, were tested in the in-bed reduction of tar and alkali halides (NaCl and KCl) released in a process of biomass steam/O(2) gasification. The tests were carried out at an ICBFB bench scale reactor under the operating conditions of: 855-890 °C, atmospheric pressure, 0.5 steam/biomass and 0.33 ER ratios. From the use of the two materials, a reduction in the contaminant contents of the fuel gas produced was found. For the alkali halides, a decrease up to 70%(wt) was observed for the potassium concentration, while for sodium, the reduction was found to be quite poor. For the organic content, compared to unmodified Olivine, the chromatographically determined total tar quantity showed a removal efficiency of 38%(wt). Moreover, regarding the particulate content a rough doubling in the fuel gas revealed a certain brittleness of the new bed material.

  11. Hydrogen production from biomass over steam gasification

    Energy Technology Data Exchange (ETDEWEB)

    Rauch, R.; Potetz, A.; Hofbauer, H. [Vienna Univ. of Technology (Austria). Inst. of Chemical Engineering; Weber, G. [Bioenergy 2020+, Guessing (Austria)

    2010-12-30

    Renewable hydrogen is one option for a clean energy carrier in the future. There were several research programs in the past, to produce hydrogen on a renewable basis by electrolysis, direct conversion of water or by gasification of biomass. None of these options were developed to a stage, that they could be used on a commercial basis. At the moment almost all hydrogen is produced from fossil fuels and one main consumer of hydrogen are refineries. So a good option to demonstrate the production of renewable hydrogen and bring it later into the market is over refineries. The most economic option to produce renewable hydrogen at the moment is over gasification of biomass. In Austria an indirect gasification system was developed and is demonstrated in Guessing, Austria. The biomass CHP Guessing uses the allothermal steam dual fluidised bed gasifier and produces a high grade product gas, which is used at the moment for the CHP in a gas engine. As there is no nitrogen in the product gas and high hydrogen content, this gas can be also used as synthesis gas or for production of hydrogen. The main aim of this paper is to present the experimental and simulation work to convert biomass into renewable hydrogen. The product gas of the indirect gasification system is mainly hydrogen, carbon monoxide, carbon dioxide and methane. Within the ERA-Net project ''OptiBtLGas'' the reforming of methane and the CO-shift reaction was investigated to convert all hydrocarbons and carbon monoxide to hydrogen. On basis of the experimental results the mass- and energy balances of a commercial 100 MW fuel input plant was done. Here 3 different cases of complexity of the overall plant were simulated. The first case was without reforming and CO-shift, only by hydrogen separation. The second case was by including steam - reforming and afterwards separation of hydrogen. The third case includes hydrocarbon reforming, CO-shift and hydrogen separation. In all cases the off-gases (CO

  12. Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2007-06-30

    University of Utah's project entitled 'Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer' (DOE Cooperative Agreement DE-FC26-02NT41490) was developed in response to a solicitation released by the U.S. Department of Energy in December 2001, requesting proposals for projects targeted towards black liquor/biomass gasification technology support research and development. Specifically, the solicitation was seeking projects that would provide technical support for Department of Energy supported black liquor and biomass gasification demonstration projects under development at the time.

  13. Study on pore structure properties of steam activated biomass chars

    Energy Technology Data Exchange (ETDEWEB)

    Shu, Tong; Lu, Fei; Wang, Qinchao; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

    2013-07-01

    Wheat straw and rice husk chars were prepared in a fixed bed reactor at different pyrolysis temperatures (673, 873 and 1,073K) and different pyrolysis procedure. The steam activated chars were also prepared in a fixed bed reactor at the following conditions: activation temperature is 1,073K, the flow rate of N{sub 2} is 5L/min, and N{sub 2} and H{sub 2}O molar ratio is 1:1. The specific surface area, pore structure and micro-morphology of different kinds of prepared biomass chars were measured by NOVA1000e analysis instrument and JSM-5610LV scanning electron microscopy (SEM), respectively. Results indicated that the internal structure was improved significantly by steam activation through enlarging the specific surface area and enriching the porosity. The wheat straw char prepared by both rapid pyrolysis at 873K and activation by steam is better than others, whose DR surface area increases from 3.10 to 1099.99m{sup 2}/g. The N{sub 2} adsorption volume of steam activated biomass chars has been significant promoted.

  14. INVESTIGATION OF FUEL CHEMISTRY AND BED PERFORMANCE IN A FLUIDIZED BED BLACK LIQUOR STEAM REFORMER

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Whitty

    2003-12-01

    The University of Utah project ''Investigation of Fuel Chemistry and Bed Performance in a Fluidized Bed Black Liquor Steam Reformer'' (DOE award number DE-FC26-02NT41490) was developed in response to a solicitation for projects to provide technical support for black liquor and biomass gasification. The primary focus of the project is to provide support for a DOE-sponsored demonstration of MTCI's black liquor steam reforming technology at Georgia-Pacific's paper mill in Big Island, Virginia. A more overarching goal is to improve the understanding of phenomena that take place during low temperature black liquor gasification. This is achieved through five complementary technical tasks: (1) construction of a fluidized bed black liquor gasification test system, (2) investigation of bed performance, (3) evaluation of product gas quality, (4) black liquor conversion analysis and modeling and (5) computational modeling of the Big Island gasifier. Four experimental devices have been constructed under this project. The largest facility, which is the heart of the experimental effort, is a pressurized fluidized bed gasification test system. The system is designed to be able to reproduce conditions near the black liquor injectors in the Big Island steam reformer, so the behavior of black liquor pyrolysis and char gasification can be quantified in a representative environment. The gasification test system comprises five subsystems: steam generation and superheating, black liquor feed, fluidized bed reactor, afterburner for syngas combustion and a flue gas cooler/condenser. The three-story system is located at University of Utah's Industrial Combustion and Gasification Research Facility, and all resources there are available to support the research.

  15. Biomass to hydrogen via fast pyrolysis and catalytic steam reforming

    Energy Technology Data Exchange (ETDEWEB)

    Chornet, E.; Wang, D.; Montane, D. [National Renewable Energy Lab., Golden, CO (United States)] [and others

    1995-09-01

    Fast pyrolysis of biomass results in a pyrolytic oil which is a mixture of (a) carbohydrate-derived acids, aldehydes and polyols, (b) lignin-derived substituted phenolics, and (c) extractives-derived terpenoids and fatty acids. The conversion of this pyrolysis oil into H{sub 2} and CO{sub 2} is thermodynamically favored under appropriate steam reforming conditions. Our efforts have focused in understanding the catalysis of steam reforming which will lead to a successful process at reasonable steam/carbon ratios arid process severities. The experimental work, carried out at the laboratory and bench scale levels, has centered on the performance of Ni-based catalysts using model compounds as prototypes of the oxygenates present in the pyrolysis oil. Steam reforming of acetic acid, hydroxyacetaldehyde, furfural and syringol has been proven to proceed rapidly within a reasonable range of severities. Time-on-stream studies are now underway using a fixed bed barometric pressure reactor to ascertain the durability of the catalysts and thus substantiate the scientific and technical feasibility of the catalytic reforming option. Economic analyses are being carried out in parallel to determine the opportunity zones for the combined fast pyrolysis/steam reforming approach. A discussion on the current state of the project is presented.

  16. Biomass gasification with oxygen and steam in a fluidized bed gasifier%生物质流化床氧气-水蒸气气化实验研究

    Institute of Scientific and Technical Information of China (English)

    苏德仁; 刘华财; 周肇秋; 阴秀丽; 吴创之

    2012-01-01

    The characteristics of biomass gasification with oxygen-steam mixtures in a fluidized bed are studied in this paper. The effects of feedstock, equivalence ratio (ER), steam to biomass ratio (S/B), gasification temperature, secondary oxygen supply and bed materials on gasification performance were investigated. The results showed that higher C and H content of feedstock was more favorable for higher H2 and CO content and lower tar content of fuel gas. The H2 content increased with gasification temperature and reached its maximum at ER=0.27 and S/B = 0.6. Higher gasification temperature (>840℃) also contributed to higher CO content. The introduction of secondary flow upper the feedstock inlet with a second flow ratio of 15% improved the gas quality significantly, and more tar was reduced as the secondary flow inlet move upward the gasifier. Dolomite and limestone performed better than olivine on cracking tar and increasing H2 content, but resulted in higher ash content.%在小型流化床气化装置上进行了氧气-水蒸气气化实验,考察了原料、当量比、水蒸气配比、温度、二次风和床料对气化特性的影响.结果表明,原料中C和H含量越高,气化气中H2和CO含量越高,焦油含量越低;当量比为0.27和水蒸气配比为0.6时,H2含量达到最大值;温度的升高可提高H2含量,在840℃以上,可提高CO含量;二次风从进料口偏上且二次风比率为15%通入,气体组分变化较明显,二次风通入点位置越高,焦油含量降低幅度越大;白云石和石灰石裂解焦油和提高H2含量的活性高于橄榄石,但同时明显提高了气体中的灰分含量.

  17. FLUIDIZED BED STEAM REFORMER MONOLITH FORMATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-12-22

    Fluidized Bed Steam Reforming (FBSR) is being considered as an alternative technology for the immobilization of a wide variety of aqueous high sodium containing radioactive wastes at various DOE facilities in the United States. The addition of clay, charcoal, and a catalyst as co-reactants converts aqueous Low Activity Wastes (LAW) to a granular or ''mineralized'' waste form while converting organic components to CO{sub 2} and steam, and nitrate/nitrite components, if any, to N{sub 2}. The waste form produced is a multiphase mineral assemblage of Na-Al-Si (NAS) feldspathoid minerals with cage-like structures that atomically bond radionuclides like Tc-99 and anions such as SO{sub 4}, I, F, and Cl. The granular product has been shown to be as durable as LAW glass. Shallow land burial requires that the mineralized waste form be able to sustain the weight of soil overburden and potential intrusion by future generations. The strength requirement necessitates binding the granular product into a monolith. FBSR mineral products were formulated into a variety of monoliths including various cements, Ceramicrete, and hydroceramics. All but one of the nine monoliths tested met the <2g/m{sup 2} durability specification for Na and Re (simulant for Tc-99) when tested using the Product Consistency Test (PCT; ASTM C1285). Of the nine monoliths tested the cements produced with 80-87 wt% FBSR product, the Ceramicrete, and the hydroceramic produced with 83.3 wt% FBSR product, met the compressive strength and durability requirements for an LAW waste form.

  18. Biomass Oxygen Enriched-steam Gasification in an Atmospheric Fluidized Bed for Syngas Production%生物质流化床富氧-水蒸气气化制备合成气研究

    Institute of Scientific and Technical Information of China (English)

    苏德仁; 周肇秋; 谢建军; 朗林; 阴秀丽; 吴创之

    2011-01-01

    Biomass gasification with steam-oxygen enriched air in an atmospheric fluidized bed gasifier was studied. The gasifier was 9 m high with the bed diameter of 0. 5 m. Sawdust with different moisture contents was used as feedstock, and it was fed into the gasifier at flow rates of 180 ~ 270 kg/h. The effects of equivalence ratio, steam to biomass ratio, secondary flow ratio and feedstock moisture on the bed temperature, gas compositions, tar content, lower heating values, gas yield, carbon conversion efficiency and cold gas efficiency were investigated. The results showed under the operating conditions of ER is 0. 25 ~ 0. 27 and S/B = 0. 4, the following syngas was obtained: H2 content of 28. 7% , H2/CO ratio of 0.94, low heating value of 9.9 MJ/m3, cold gas efficiency was more than 75% , carbon conversion efficiency was more than 97% ; a second flow ratio of 25% at the ER of 0. 29 can significantly reduce the tar content to 49 mg/m , but hardly improve the quality of the gas produced; the rise of the feedstock moisture content caused a significant increase in CO2 content and a reduction in H2 and CO contents, and the moisture content is expected not to exceed 20% .%使用不同含水率的木粉为原料,以180~270 kg/h的进料速度在内径0.5 m、高9 m的常压流化床气化炉上进行了富氧-水蒸气气化制备合成气实验.考察了当量比、水蒸气配比、二次风以及原料含水率对气化温度、燃气组分、低位热值、气体产率、气化效率和碳转化率等参数的影响.结果显示:当量比为0.25~0.27之间,水蒸气配比0.4时,H:含量最高可达28.7%,H2/CO为0.94,燃气热值9.9 MJ/m3,气化效率大于75%,碳转化率大于97%;提高二次风比率可明显降低焦油含量,在总当量比0.29、二次风比率25%时焦油含量为49 ms/m3;原料水分增加,气体质量下降,含水率以不超过20%为宜.

  19. Parametric Optimization of Biomass Steam-and-Gas Plant

    Directory of Open Access Journals (Sweden)

    V. Sednin

    2013-01-01

    Full Text Available The paper contains a parametric analysis of the simplest scheme of a steam-and gas plant for the conditions required for biomass burning. It has been shown that application of gas-turbine and steam-and-gas plants can significantly exceed an efficiency of steam-power supply units which are used at the present moment. Optimum thermo-dynamical conditions for application of steam-and gas plants with the purpose to burn biomass require new technological solutions in the field of heat-exchange equipment designs.

  20. Investigations on catalyzed steam gasification of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Mudge, L.K.; Weber, S.L.; Mitchell, D.H.; Sealock, L.J. Jr.; Robertus, R.J.

    1981-01-01

    The purpose of the study is to evaluate the technical and economic feasibility of producing specific gas products via the catalytic gasification of biomass. This report presents the results of research conducted from December 1977 to October 1980. The study was comprised of laboratory studies, process development, and economic analyses. The laboratory studies were conducted to develop operating conditions and catalyst systems for generating methane-rich gas, synthesis gases, hydrogen, and carbon monoxide; these studies also developed techniques for catalyst recovery, regeneration, and recycling. A process development unit (PDU) was designed and constructed to evaluate laboratory systems at conditions approximating commercial operations. The economic analyses, performed by Davy McKee, Inc. for PNL, evaluated the feasibility of adapting the wood-to-methane and wood-to-methanol processes to full-scale commercial operations. Plants were designed in the economic analyses to produce fuel-grade methanol from wood and substitute natural gas (SNG) from wood via catalytic gasification with steam.

  1. Parametric experimental tests of steam gasification of pine wood in a fluidized bed reactor

    Directory of Open Access Journals (Sweden)

    L. Vecchione

    2013-09-01

    Full Text Available Among Renewable Energy Sources (RES, biomass represent one of the most common and suitable solution in order to contribute to the global energy supply and to reduce greenhouse gases (GHG emissions. The disposal of some residual biomass, as pruning from pine trees, represent a problem for agricultural and agro-industrial sectors. But if the residual biomass are used for energy production can become a resource. The most suitable energy conversion technology for the above-mentioned biomass is gasification process because the high C/N ratio and the low moisture content, obtained from the analysis. In this work a small-pilot bubbling-bed gasification plant has been designed, constructed and used in order to obtain, from the pine trees pruning, a syngas with low tar and char contents and high hydrogen content. The activities showed here are part of the activities carried out in the European 7FP UNIfHY project. In particular the aim of this work is to develop experimental test on a bench scale steam blown fluidized bed biomass gasifier. These tests will be utilized in future works for the simulations of a pilot scale steam fluidized bed gasifier (100 kWth fed with different biomass feedstock. The results of the tests include produced gas and tar composition as well gas, tar and char yield. Tests on a bench scale reactor (8 cm I.D. were carried out varying steam to biomass ratio from 0.5, 0.7 and 1 to 830°C.

  2. Liquid Fuel Production from Biomass via High Temperature Steam Electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Grant L. Hawkes; Michael G. McKellar

    2009-11-01

    A process model of syngas production using high temperature electrolysis and biomass gasification is presented. Process heat from the biomass gasifier is used to heat steam for the hydrogen production via the high temperature steam electrolysis process. Hydrogen from electrolysis allows a high utilization of the biomass carbon for syngas production. Oxygen produced form the electrolysis process is used to control the oxidation rate in the oxygen-fed biomass gasifier. Based on the gasifier temperature, 94% to 95% of the carbon in the biomass becomes carbon monoxide in the syngas (carbon monoxide and hydrogen). Assuming the thermal efficiency of the power cycle for electricity generation is 50%, (as expected from GEN IV nuclear reactors), the syngas production efficiency ranges from 70% to 73% as the gasifier temperature decreases from 1900 K to 1500 K. Parametric studies of system pressure, biomass moisture content and low temperature alkaline electrolysis are also presented.

  3. Adsorption characteristics of SO{sub 2}, NO by steam activated biomass chars

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Fei; Shu, Tong; Wang, Kuan; Lu, Ping [Nanjing Normal Univ. (China). School of Energy and Mechanical Engineering

    2013-07-01

    Wheat straw and rice husk collected from the suburb of Nanjing, China, were prepared to different kinds of steam activated biomass-based chars, and the adsorption characteristics of the biomass-based chars was carried out in a fixed bed reactor. The specific surface area and pore structure of different biomass chars were measured by nitrogen adsorption-desorption analysis instrument at 77K. The effects of biomass type, pyrolysis temperature, heating rate, activation temperature and concentration of SO{sub 2}, NO on the adsorption efficiency of SO{sub 2}, NO were analyzed. The results indicated that the steam activation has significant effects on the specific surface area, total pore volume and micro-morphology of biomass chars by improving the internal structure. The adsorption efficiency of SO{sub 2}, NO increased with the decreasing of SO{sub 2}, NO concentration in the experimental range. The optimal condition of char preparation (873K, fast pyrolysis) and steam activation (1,073K) was proposed based on the adsorption efficiency and adsorption volume of SO{sub 2}, NO. It builds a theoretical basis for industrial applications of biomass.

  4. Hydrogen production from algal biomass via steam gasification.

    Science.gov (United States)

    Duman, Gozde; Uddin, Md Azhar; Yanik, Jale

    2014-08-01

    Algal biomasses were tested as feedstock for steam gasification in a dual-bed microreactor in a two-stage process. Gasification experiments were carried out in absence and presence of catalyst. The catalysts used were 10% Fe₂O₃-90% CeO₂ and red mud (activated and natural forms). Effects of catalysts on tar formation and gasification efficiencies were comparatively investigated. It was observed that the characteristic of algae gasification was dependent on its components and the catalysts used. The main role of the catalyst was reforming of the tar derived from algae pyrolysis, besides enhancing water gas shift reaction. The tar reduction levels were in the range of 80-100% for seaweeds and of 53-70% for microalgae. Fe₂O₃-CeO₂ was found to be the most effective catalyst. The maximum hydrogen yields obtained were 1036 cc/g algae for Fucus serratus, 937 cc/g algae for Laminaria digitata and 413 cc/g algae for Nannochloropsis oculata.

  5. Modeling biomass gasification in circulating fluidized beds

    Science.gov (United States)

    Miao, Qi

    In this thesis, the modeling of biomass gasification in circulating fluidized beds was studied. The hydrodynamics of a circulating fluidized bed operating on biomass particles were first investigated, both experimentally and numerically. Then a comprehensive mathematical model was presented to predict the overall performance of a 1.2 MWe biomass gasification and power generation plant. A sensitivity analysis was conducted to test its response to several gasifier operating conditions. The model was validated using the experimental results obtained from the plant and two other circulating fluidized bed biomass gasifiers (CFBBGs). Finally, an ASPEN PLUS simulation model of biomass gasification was presented based on minimization of the Gibbs free energy of the reaction system at chemical equilibrium. Hydrodynamics plays a crucial role in defining the performance of gas-solid circulating fluidized beds (CFBs). A 2-dimensional mathematical model was developed considering the hydrodynamic behavior of CFB gasifiers. In the modeling, the CFB riser was divided into two regions: a dense region at the bottom and a dilute region at the top of the riser. Kunii and Levenspiel (1991)'s model was adopted to express the vertical solids distribution with some other assumptions. Radial distributions of bed voidage were taken into account in the upper zone by using Zhang et al. (1991)'s correlation. For model validation purposes, a cold model CFB was employed, in which sawdust was transported with air as the fluidizing agent. A comprehensive mathematical model was developed to predict the overall performance of a 1.2 MWe biomass gasification and power generation demonstration plant in China. Hydrodynamics as well as chemical reaction kinetics were considered. The fluidized bed riser was divided into two distinct sections: (a) a dense region at the bottom of the bed where biomass undergoes mainly heterogeneous reactions and (b) a dilute region at the top where most of homogeneous

  6. Energy balance for steam generation system with biomass dryer

    Energy Technology Data Exchange (ETDEWEB)

    Ramos, Pedro A.R. [Instituto Superior Politecnico Jose Antonio Echeverria (CUJAE), Ciudad de La Habana (Cuba). Facultad Ingenieria Mecanica]. E-mail: pedro@economia.cujae.edu.cu; Lombardi, Geraldo; Santos, Antonio Moreira dos [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Escola de Engenharia]. E-mails: lombardi@sc.usp.br; asantos@sc.usp.br

    2008-07-01

    Water content is a major drainer of the energy available in the biomass, which justifies the proposal of a drying system with the potential to increase 80% of the biomass low heating value, also increasing the production of steam in the boiler and cogeneration of electricity. An example of biomass is the sugar cane bagasse of an alcohol mill producing 120,000 liters of alcohol per day, whose humidity from the extraction section is usually 50%. The present paper determines the increases in the mass flow rates of steam in the boiler, in the cogeneration of electricity and in the pay back time of the drying system and of the alcohol mill, as a consequence of the bagasse drying from 50 to 35%, considering 30% of air excess over the stoichiometric value admitted in the boiler for the bagasse burning. It also provides subsidies for the development and deployment of a drying system for the current boilers. (author)

  7. The Improved Updraft Fixed-bed Biomass Gasifier and Its Application in Steam Boiler Instead of Fuel Oil%改进型固定床上吸式气化炉及其在蒸汽锅炉中的代油燃烧应用

    Institute of Scientific and Technical Information of China (English)

    杜海江; 郭常青; 徐冰嬿; 李宗楠; 刘光华

    2015-01-01

    在蒸汽锅炉进行生物质能源改造中,生物质气化燃气代替煤、油具有成本、环保、政策方面的优势,但必须解决焦油的二次污染问题。本文提出以改进型即中部出气固定床上吸式气化炉生产生物质可燃气,及焦油成分随燃气直接在锅炉炉膛燃烧的技术路线,并以2T/h蒸汽锅炉为例对气化炉的主要结构参数进行设计计算。采用基于锅炉输出蒸汽压力的气化炉鼓风自适应控制方法实现系统的闭环控制。最后通过实际应用案例实测数据的热能计算证明生物质气化燃气在蒸汽锅炉中代替煤、油燃烧的可行性。%For biomass energy transformation in steam boilers, gasification gas has more advantages than coal or oil, such as cost, environmental protection, and policy benefits. However, we must solve the problem of secondary pollution out of tar in its application. In this paper, firstly we propose an improved technical solution, which can produce high heat value, low tar content biomass gas by updraft fixed-bed biomass gasifier with gas outlet in the middle position, and the tar composition burned directly in boiler furnace with biomass gas. Based on the technical solution, we take 2 T/h steam boiler for example to design and calculate the main structure parameters of the gasifier. Next, we provide an intelligent adaptive control on air supply of gasifier according to steam pressure. Finally, the feasibility and efficiency of biomass gas as a new boiler fuel was proved through the test data in practical application cases.

  8. Bio-syngas production from agro-industrial biomass residues by steam gasification.

    Science.gov (United States)

    Pacioni, Tatiana Ramos; Soares, Diniara; Domenico, Michele Di; Rosa, Maria Fernanda; Moreira, Regina de Fátima Peralta Muniz; José, Humberto Jorge

    2016-12-01

    This study evaluated the steam gasification potential of three residues from Brazilian agro-industry by assessing their reaction kinetics and syngas production at temperatures from 650 to 850°C and a steam partial pressure range of 0.05 to 0.3bar. The transition temperature between kinetic control and diffusion control regimes was identified. Prior to the gasification tests, the raw biomasses, namely apple pomace, spent coffee grounds and sawdust, were pyrolyzed in a fixed-bed quartz tubular reactor under controlled conditions. Gasification tests were performed isothermally in a magnetic suspension thermobalance and the reaction products were analyzed by a gas chromatograph with TCD/FID detectors. According to the characterization results, the samples presented higher carbon and lower volatile matter contents than the biomasses. Nevertheless, all of the materials had high calorific value. Syngas production was influenced by both temperature and steam partial pressure. Higher concentrations of H2 and CO were found in the conversion range of 50-80% and higher concentrations of CO2 in conversions around 10%, for all the gasified biochars. The H2/CO decreased with increasing temperature, mainly in kinetic control regime, in the lower temperature range. The results indicate the gasification potential of Brazilian biomass residues and are an initial and important step in the development of gasification processes in Brazil. Copyright © 2016 Elsevier Ltd. All rights reserved.

  9. Fixed bed gasification of solid biomass fuels

    Energy Technology Data Exchange (ETDEWEB)

    Haavisto, I. [Condens Oy, Haemeenlinna (Finland)

    1996-12-31

    Fixed bed biomass gasifiers are feasible in the effect range of 100 kW -10 MW. Co-current gasification is available only up to 1 MW for technical reasons. Counter-current gasifiers have been used in Finland and Sweden for 10 years in gasification heating plants, which are a combination of a gasifier and an oil boiler. The plants have proved to have a wide control range, flexible and uncomplicated unmanned operation and an excellent reliability. Counter-current gasifiers can be applied for new heating plants or for converting existing oil and natural gas boilers into using solid fuels. There is a new process development underway, aiming at motor use of the producer gas. The development work involves a new, more flexible cocurrent gasifier and a cleaning step for the counter-current producer gas. (orig.)

  10. Exergoeconomic analysis of small-scale biomass steam cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez Sotomonte, Cesar Adolfo; Lora, Electo Eduardo Silva [Universidade Federal de Itajuba, MG (Brazil)], e-mails: c.rodriguez32@unifei.edu.br, electo@unifei.edu.br; Venturini, Osvaldo Jose; Escobar, Jose Carlos [Universidad Federal de Itajuba, MG (Brazil)], e-mail: osvaldo@unifei.edu.br

    2010-07-01

    The principal objective of this work is to develop a calculation process, based on the second law of thermodynamics, for evaluating the thermoeconomic potential of a small steam cogeneration plant using waste from pulp processing and/or sawmills as fuel. Four different configurations are presented and assessed. The exergetic efficiency of the cycles that use condensing turbines is found to be around 11%, which has almost 3 percent higher efficiency than cycles with back pressure turbines. The thermoeconomic equations used in this paper estimated the production costs varying the fuel price. The main results show that present cost of technologies in a small-scale steam cycle cogeneration do not justify the implementation of more efficient systems for biomass prices less than 100 R$/t. (author)

  11. Gasification of biomass chars in steam-nitrogen mixture

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H. [Department of Chemical Engineering, Chemical and Metallurgical Engineering Faculty, Istanbul Technical University, 34469 Maslak, Istanbul (Turkey)]. E-mail: hanzade@itu.edu.tr; Yaman, S. [Department of Chemical Engineering, Chemical and Metallurgical Engineering Faculty, Istanbul Technical University, 34469 Maslak, Istanbul (Turkey); Kucukbayrak, S. [Department of Chemical Engineering, Chemical and Metallurgical Engineering Faculty, Istanbul Technical University, 34469 Maslak, Istanbul (Turkey)

    2006-05-15

    Some agricultural and waste biomass samples such as sunflower shell, pinecone, rapeseed, cotton refuse and olive refuse were first pyrolyzed in nitrogen, and then, their chars were gasified in a gas mixture of steam and nitrogen. Experiments were performed using the thermogravimetric analysis technique. Pyrolysis of the biomass samples was performed at a heating rate of 20 K/min from ambient to 1273 K in a dynamic nitrogen atmosphere of 40 cm{sup 3} min{sup -1}. The obtained chars were cooled to ambient temperature and then gasified up to 1273 K in a dynamic atmosphere of 40 cm{sup 3} min{sup -1} of a mixture of steam and nitrogen. Derivative thermogravimetric analysis profiles from gasification of the chars were derived, and the mass losses from the chars were interpreted in terms of temperature. It was concluded that gasification characteristics of biomass chars were fairly dependent on the biomass properties such as ash and fixed carbon contents and the constituents present in the ash. Different mechanisms in the three temperature intervals, namely water desorption at lower temperatures, decomposition of hydroxide minerals to oxide minerals and formation of carbon monoxide at medium temperatures and production of hydrogen at high temperatures govern the behavior of the char during the gasification process. The chars from pinecone and sunflower shell could be easily gasified under the mentioned conditions. In order to further raise the conversion yields, long hold times should be applied at high temperatures. However, the chars from rapeseed and olive refuse were not gasified satisfactorily. Low ash content and high fixed carbon content biomass materials are recommended for use in gasification processes when char from pyrolysis at elevated temperatures is used as a feedstock.

  12. H₂-rich syngas production by fluidized bed gasification of biomass and plastic fuel.

    Science.gov (United States)

    Ruoppolo, G; Ammendola, P; Chirone, R; Miccio, F

    2012-04-01

    This paper reports the results of gasification tests using a catalytic fluidized bed gasifier to obtain a H(2)-rich stream by feeding different pellets made of wood, biomass/plastic and olive husks to the gasifier. The effects of both the steam supply and an in-bed catalyst on gasifier performance have been investigated. In general, pelletization was an effective pre-treatment for improving the homogeneity of the fuel and the reliability of the feeding devices. The use of biomass/plastic pellets in a catalyst bed yielded good results in terms of the hydrogen concentration (up to 32%vol.), even if an increase in tar production and in the fine/carbon elutriation rate was observed in comparison with wood pellets.

  13. Biomass-to-hydrogen via fast pyrolysis and catalytic steam reforming

    Energy Technology Data Exchange (ETDEWEB)

    Chornet, E.; Wang, D.; Czernik, S. [National Renewable Energy Lab., Golden, CO (United States)] [and others

    1996-10-01

    Pyrolysis of lignocellulosic biomass and reforming the pyroligneous oils is being studied as a strategy for producing hydrogen. Novel technologies for the rapid pyrolysis of biomass have been developed in the past decade. They provide compact and efficient systems to transform biomass into vapors that are condensed to oils, with yields as high as 75-80 wt.% of the anhydrous biomass. This {open_quotes}bio-oil{close_quotes} is a mixture of aldehydes, alcohols, acids, oligomers from the constitutive carbohydrates and lignin, and some water derived from the dehydration reactions. Hydrogen can be produced by reforming the bio-oil or its fractions with steam. A process of this nature has the potential to be cost competitive with conventional means of producing hydrogen. The reforming facility can be designed to handle alternate feedstocks, such as natural gas and naphtha, if necessary. Thermodynamic modeling of the major constituents of the bio-oil has shown that reforming is possible within a wide range of temperatures and steam-to-carbon ratios. Existing catalytic data on the reforming of oxygenates have been studied to guide catalyst selection. Tests performed on a microreactor interfaced with a molecular beam mass spectrometer showed that, by proper selection of the process variables: temperature, steam-to-carbon ratio, gas hourly space velocity, and contact time, almost total conversion of carbon in the feed to CO and CO{sub 2} could be obtained. These tests also provided possible reaction mechanisms where thermal cracking competes with catalytic processes. Bench-scale, fixed bed reactor tests demonstrated high hydrogen yields from model compounds and carbohydrate-derived pyrolysis oil fractions. Reforming bio-oil or its fractions required proper dispersion of the liquid to avoid vapor-phase carbonization of the feed in the inlet to the reactor. A special spraying nozzle injector was designed and successfully tested with an aqueous fraction of bio-oil.

  14. Technoeconomic study on steam explosion application in biomass processing.

    Science.gov (United States)

    Zimbardi, Francesco; Ricci, Esmeralda; Braccio, Giacobbe

    2002-01-01

    This work is based on the data collected during trials of a continuous steam explosion (SE) plant, with a treatment capacity of about 350 kg/h, including the biomass fractionation section. The energy and water consumption, equipment cost, and manpower needed to run this plant have been used as the base case for a techno-economic evaluation of productive plants. Three processing plant configurations have been considered: (I) SE pretreatment only; (II) SE followed by the hemicellulose extraction; (III) SE followed by the sequential hemicellulose and lignin extractions. The biomass treatment cost has been evaluated as a function of the plant scale. For each configuration, variable and fixed cost breakdown has been detailed in the case of a 50,000 t/y plant.

  15. On the gasification of biomass in a steam-oxygen blown CFB gasifier with the focus on gas quality upgrading: technology background, experiments and mathematical modeling

    NARCIS (Netherlands)

    Siedlecki, M.

    2011-01-01

    This work presents and discusses the results of the research on the gasification of biomass in an atmospheric circulating fluidized bed, with a mixture of steam and oxygen as fluidization / gasification medium. The main objectives of this research were to investigate and improve the gasification pro

  16. On the gasification of biomass in a steam-oxygen blown CFB gasifier with the focus on gas quality upgrading: technology background, experiments and mathematical modeling

    NARCIS (Netherlands)

    Siedlecki, M.

    2011-01-01

    This work presents and discusses the results of the research on the gasification of biomass in an atmospheric circulating fluidized bed, with a mixture of steam and oxygen as fluidization / gasification medium. The main objectives of this research were to investigate and improve the gasification pro

  17. Bed Agglomeration During the Steam Gasification of a High Lignin Corn Stover Simultaneous Saccharification and Fermentation (SSF) Digester Residue

    Energy Technology Data Exchange (ETDEWEB)

    Howe, Daniel T.; Taasevigen, Danny J.; Gerber, Mark A.; Gray, Michel J.; Fernandez, Carlos A.; Saraf, Laxmikant; Garcia-Perez, Manuel; Wolcott, Michael P.

    2015-11-13

    This research investigates the bed agglomeration phenomena during the steam gasification of a high lignin residue produced from the simultaneous saccharification and fermentation (SSF) of corn stover in a bubbling fluidized bed. The studies were conducted at 895°C using alumina as bed material. Biomass was fed at 1.5 kg/hr, while steam was fed to give a velocity equal to 2.5 times the minimum fluidization velocity, with a steam/carbon ratio of 0.9. The pelletized feedstock was co-fed with a cooling nitrogen stream to mitigate feed line plugging issues. Tar production was high at 50.3 g/Nm3, and the fraction of C10+ compounds was greater than that seen in the gasification of traditional lignocellulosic feedstocks. Carbon closures over 94 % were achieved for all experiments. Bed agglomeration was found to be problematic, indicated by pressure drop increases observed below the bed and upstream of the feed line. Two size categories of solids were recovered from the reactor, +60 mesh and -60 mesh. After a 2.75-hour experiment, 61.7 wt % was recovered as -60 mesh particles and 38.2 wt% of the recovered reactor solids were +60 mesh. A sizeable percentage, 31.8 wt%, was +20 mesh. The -60 mesh particles were mainly formed by the initial bed material (Al2O3). Almost 50 wt. % of the + 20 mesh particles was found to be formed by organics. The unreacted carbon remaining in the reactor resulted in a low conversion rate to product gas. ICP-AES, SEM, SEM-EDS, and XRD confirmed that the large agglomerates (+ 20 mesh) were not encapsulated bed material but rather un-gasified feedstock pellets with sand particles attached to it.

  18. FLUIDIZED BED STEAM REFORMING ENABLING ORGANIC HIGH LEVEL WASTE DISPOSAL

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M

    2008-05-09

    Waste streams planned for generation by the Global Nuclear Energy Partnership (GNEP) and existing radioactive High Level Waste (HLW) streams containing organic compounds such as the Tank 48H waste stream at Savannah River Site have completed simulant and radioactive testing, respectfully, by Savannah River National Laboratory (SRNL). GNEP waste streams will include up to 53 wt% organic compounds and nitrates up to 56 wt%. Decomposition of high nitrate streams requires reducing conditions, e.g. provided by organic additives such as sugar or coal, to reduce NOX in the off-gas to N2 to meet Clean Air Act (CAA) standards during processing. Thus, organics will be present during the waste form stabilization process regardless of the GNEP processes utilized and exists in some of the high level radioactive waste tanks at Savannah River Site and Hanford Tank Farms, e.g. organics in the feed or organics used for nitrate destruction. Waste streams containing high organic concentrations cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by pretreatment. The alternative waste stabilization pretreatment process of Fluidized Bed Steam Reforming (FBSR) operates at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). The FBSR process has been demonstrated on GNEP simulated waste and radioactive waste containing high organics from Tank 48H to convert organics to CAA compliant gases, create no secondary liquid waste streams and create a stable mineral waste form.

  19. Development of a supported tri-metallic catalyst and evaluation of the catalytic activity in biomass steam gasification.

    Science.gov (United States)

    Li, Jianfen; Xiao, Bo; Yan, Rong; Xu, Xiaorong

    2009-11-01

    A supported tri-metallic catalyst (nano-Ni-La-Fe/gamma-Al(2)O(3)) was developed for tar reduction and enhanced hydrogen production in biomass steam gasification, with focuses on preventing coke deposition and sintering effects to lengthen the lifetime of developed catalysts. The catalyst was prepared by deposition-precipitation method and characterized by various analytical approaches. Following that, the activity of catalysts in biomass steam gasification was investigated in a bench-scale combined fixed bed reactor. With presence of the catalyst, the content of hydrogen in gas products was increased to over 10 vol.%, the tar removal efficiency reached 99% at 1073 K, and more importantly the coke deposition on the catalyst surfaces and sintering effects were avoided, leading to a long lifetime of catalysts.

  20. Sorption-enhanced steam methane reforming in fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Johnsen, Kim

    2006-10-15

    Hydrogen is considered to be an important potential energy carrier; however, its advantages are unlikely to be realized unless efficient means can be found to produce it without generation of CO{sub 2}. Sorption-enhanced steam methane reforming (SE-SMR) represent a novel, energy-efficient hydrogen production route with in situ CO{sub 2} capture, shifting the reforming and water gas shift reactions beyond their conventional thermodynamic limits. The use of fluidized bed reactors for SE-SMR has been investigated. Arctic dolomite, a calcium-based natural sorbent, was chosen as the primary CO{sub 2}-acceptor in this study due to high absorption capacity, relatively high reaction rate and low cost. An experimental investigation was conducted in a bubbling fluidized bed reactor of diameter 0.1 m, which was operated cyclically and batch wise, alternating between reforming/carbonation conditions and higher-temperature calcination conditions. Hydrogen concentrations of >98 mole% on a dry basis were reached at 600 C and 1 atm, for superficial gas velocities in the range of {approx}0.03-0.1 m/s. Multiple reforming-regeneration cycles showed that the hydrogen concentration remained at {approx}98 mole% after four cycles. The total production time was reduced with an increasing number of cycles due to loss of CO{sub 2}-uptake capacity of the dolomite, but the reaction rates of steam reforming and carbonation seemed to be unaffected for the conditions investigated. A modified shrinking core model was applied for deriving carbonation kinetics of Arctic dolomite, using experimental data from a novel thermo gravimetric reactor. An apparent activation energy of 32.6 kj/mole was found from parameter fitting, which is in good agreement with previous reported results. The derived rate expression was able to predict experimental conversion up to {approx}30% very well, whereas the prediction of higher conversion levels was poorer. However, the residence time of sorbent in a continuous

  1. Sorption-enhanced steam methane reforming in fluidized bed reactors

    Energy Technology Data Exchange (ETDEWEB)

    Johnsen, Kim

    2006-10-15

    Hydrogen is considered to be an important potential energy carrier; however, its advantages are unlikely to be realized unless efficient means can be found to produce it without generation of CO{sub 2}. Sorption-enhanced steam methane reforming (SE-SMR) represent a novel, energy-efficient hydrogen production route with in situ CO{sub 2} capture, shifting the reforming and water gas shift reactions beyond their conventional thermodynamic limits. The use of fluidized bed reactors for SE-SMR has been investigated. Arctic dolomite, a calcium-based natural sorbent, was chosen as the primary CO{sub 2}-acceptor in this study due to high absorption capacity, relatively high reaction rate and low cost. An experimental investigation was conducted in a bubbling fluidized bed reactor of diameter 0.1 m, which was operated cyclically and batch wise, alternating between reforming/carbonation conditions and higher-temperature calcination conditions. Hydrogen concentrations of >98 mole% on a dry basis were reached at 600 C and 1 atm, for superficial gas velocities in the range of {approx}0.03-0.1 m/s. Multiple reforming-regeneration cycles showed that the hydrogen concentration remained at {approx}98 mole% after four cycles. The total production time was reduced with an increasing number of cycles due to loss of CO{sub 2}-uptake capacity of the dolomite, but the reaction rates of steam reforming and carbonation seemed to be unaffected for the conditions investigated. A modified shrinking core model was applied for deriving carbonation kinetics of Arctic dolomite, using experimental data from a novel thermo gravimetric reactor. An apparent activation energy of 32.6 kj/mole was found from parameter fitting, which is in good agreement with previous reported results. The derived rate expression was able to predict experimental conversion up to {approx}30% very well, whereas the prediction of higher conversion levels was poorer. However, the residence time of sorbent in a continuous

  2. High Temperature Air/Steam Gasification of Biomass Wastes - Stage 1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Blasiak, Wlodzimierz; Szewczyk, Dariusz; Lucas, Carlos; Rafidi, Nabil; Abeyweera Ruchira; Jansson, Anna; Bjoerkman, Eva [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Materials Science and Engineering

    2003-05-01

    In Jan 2002 the Division of Energy and Furnace Technology started the project High Temperature Air an Steam Gasification (HTAG) of biomass wastes, following the approval made by Swedish Energy Agency. The research proved successful; with the fixed bed updraft gasifier coupled to the highly regenerative preheater equipment able to produce a fuel gas not only from wood pellets but also from wood chips, bark and charcoal with considerably reduced amount of tar. This report provides information on solid biomass conversion into fuel gas as a result of air and steam gasification process performed in a fixed bed updraft gasifier. The first chapter of the report presents the overall objectives and the specific objectives of the work. Chapter 2 summarizes state-of-the-art on the gasification field stating some technical differences between low and high temperature gasification processes. Description and schemes of the experimental test rig are provided in Chapter 3. The equipment used to perform measurements of different sort and that installed in the course of the work is described in Chapter 4. Chapter 5 describes the methodology of experiments conducted whose results were processed and evaluated with help of the scheme of equations presented in Chapter 6, called raw data evaluation. Results of relevant experiments are presented and discussed in Chapter 7. A summary discussion of the tar analysis is presented in Chapter 8. Chapter 9 summarizes the findings of the research work conducted and identifies future efforts to ensure the development of next stage. Final chapter provides a summary of conclusions and recommendations of the work. References are provided at the end of the report. Aimed to assist the understanding of the work done, tables and graphs of experiments conducted, irrespective to their quality, are presented in appendices.

  3. Testing of downstream catalysts for tar destruction with a guard bed in a fluidised bed biomass gasifier at pilot plant scale

    Energy Technology Data Exchange (ETDEWEB)

    Aznar, M.P.; Frances, E.; Campos, I.J.; Martin, J.A.; Gil, J. [Saragossa Univ. (Spain). Dept. of Chemistry and Environment Engineering; Corella, J. [Complutense Univ. of Madrid (Spain). Dept. of Chemical Engineering

    1996-12-31

    A new pilot plant for advanced gasification of biomass in a fast fluidised bed is now fully operative at University of Saragossa, Spain. It is a `3rd generation` pilot plant. It has been built up after having used two previous pilot plants for biomass gasification. The main characteristic of this pilot plant is that it has two catalytic reactors connected in series, downstream the biomass gasifier. Such reactors, of 4 cm i.d., are placed in a slip stream in a by-pass from the main gasifier exit gas. The gasification is made at atmospheric pressure, with flow rates of 3-50 kg/in, using steam + O{sub 2} mixtures as the gasifying agent. Several commercial Ni steam-reforming catalyst are being tested under a realistic raw gas composition. Tar eliminations or destructions higher than 99 % are easily achieved. (orig.) 2 refs.

  4. FLUIDIZED BED STEAM REFORMER (FBSR) PRODUCT: MONOLITH FORMATION AND CHARACTERIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2006-09-13

    The most important requirement for Hanford's low activity waste (LAW) form for shallow land disposal is the chemical durability of the product. A secondary, but still essential specification, is the compressive strength of the material with regards to the strength of the material under shallow land disposal conditions, e.g. the weight of soil overburden and potential intrusion by future generations, because the term ''near-surface disposal'' indicates disposal in the uppermost portion, or approximately the top 30 meters, of the earth's surface. The THOR{reg_sign} Treatment Technologies (TTT) mineral waste form for LAW is granular in nature because it is formed by Fluidized Bed Steam Reforming (FBSR). As a granular product it has been shown to be as durable as Hanford's LAW glass during testing with ASTM C-1285-02 known as the Product Consistency Test (PCT) and with the Single Pass Flow Through Test (SPFT). Hanford Envelope A and Envelope C simulants both performed well during PCT and SPFT testing and during subsequent performance assessment modeling. This is partially due to the high aluminosilicate content of the mineral product which provides a natural aluminosilicate buffering mechanism that inhibits leaching and is known to occur in naturally occurring aluminosilicate mineral analogs. In order for the TTT Na-Al-Si (NAS) granular mineral product to meet the compressive strength requirements (ASTM C39) for a Hanford waste form, the granular product needs to be made into a monolith or disposed of in High Integrity Containers (HIC's). Additionally, the Hanford intruder scenario for disposal in the Immobilized Low Activity Waste (ILAW) trench is mitigated as there is reduced intruder exposure when a waste form is in a monolithic form. During the preliminary testing of a monolith binder for TTT's FBSR mineral product, four parameters were monitored: (1) waste loading (not optimized for each waste form tested); (2) density

  5. Integration of mixed conducting membranes in an oxygen–steam biomass gasification process

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Soprani, Stefano; Søgaard, Martin

    2013-01-01

    Oxygen–steam biomass gasification produces a high quality syngas with a high H2/CO ratio that is suitable for upgrading to liquid fuels. Such a gas is also well suited for use in conjunction with solid oxide fuel cells giving rise to a system yielding high electrical efficiency based on biomass....... The two configurations demonstrating the highest efficiency are then thermally integrated into an oxygen– steam biomass gasification plant. The energy demand for oxygen production and the membrane area required for a 6 MWth biomass plant are calculated for different operating conditions. Increasing...

  6. Biofluid process: fluidised-bed gasification of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Dittrich, A. [ATEKO a.s., Hradec Kralove (Czech Republic)

    1996-12-31

    Fluidised-bed gasification of biomass was developed by ATEKO by using long-term experience from coal gasification. An experimental unit was built and a number of tests, first with sawdust gasification, were carried out. A gas combustion engine combined with a power generator was installed and operated in power production. (orig.)

  7. Co-gasification of Colombian coal and biomass in fluidized bed: An experimental study

    Energy Technology Data Exchange (ETDEWEB)

    Jhon F. Velez; Farid Chejne; Carlos F. Valdes; Eder J. Emery; Carlos A. Londono [Universidad Nacional de Colombia, Antioquia (Colombia). Grupo de Termodinamica Aplicada y Energias Alternativas

    2009-03-15

    The main results of an experimental work on co-gasification of Colombian biomass/coal blends in a fluidized bed working at atmospheric pressure are reported in this paper. Several samples of blends were prepared by mixing 6-15wt% biomass (sawdust, rice or coffee husk) with coal. Experimental assays were carried out by using mixtures of different steams/blends (Rvc) and air/blend (Rac) ratios showing the feasibility to implement co-gasification as energetic alternative to produce fuel gas to heat and to generate electricity and the possibility of converting clean and efficiently the refuse coal to a low-heating value gas. 29 refs., 5 figs., 4 tabs.

  8. Effectiveness factors for a commercial steam reforming (Ni) catalyst and for a calcined dolomite used downstream biomass gasifiers

    Energy Technology Data Exchange (ETDEWEB)

    Corella, J.; Narvaez, I.; Orio, A. [Madrid Univ. (Spain). Dept. of Chem. Eng.

    1996-12-31

    A commercial steam reforming catalyst from BASF, the G1-25 S one, and a calcined dolomite, Norte-1, from Cantabria-Spain, have been used, once crushed and sieved to different particle fractions between 1.0 and 4.0 mm. The materials have been tested downstream small pilot biomass gasifiers, bubbling fluidized bed type, gasifying with air and with steam. The Thiele modulus and the effectiveness factor have been calculated at temperatures of 750-850 deg C. It is experimentally shown that diffusion control plays an important part when particle size is larger than ca. 0.5 mm. This has to be taken into account when comparing the quality of the solids for tar elimination. (author) (5 refs.)

  9. Modeling of reaction kinetics in bubbling fluidized bed biomass gasification reactor

    Energy Technology Data Exchange (ETDEWEB)

    Thapa, R.K.; Halvorsen, B.M. [Telemark University College, Kjolnes ring 56, P.O. Box 203, 3901 Porsgrunn (Norway); Pfeifer, C. [University of Natural Resources and Life Sciences, Vienna (Austria)

    2013-07-01

    Bubbling fluidized beds are widely used as biomass gasification reactors as at the biomass gasification plant in Gussing, Austria. The reactor in the plant is a dual circulating bubbling fluidized bed gasification reactor. The plant produces 2MW electricity and 4.5MW heat from the gasification of biomass. Wood chips as biomass and olivine particles as hot bed materials are fluidized with high temperature steam in the reactor. As a result, biomass undergoes endothermic chemical reaction to produce a mixture of combustible gases in addition to some carbon-dioxide (CO2). The combustible gases are mainly hydrogen (H2), carbon monoxide (CO) and methane (CH4). The gas is used to produce electricity and heat via utilization in a gas engine. Alternatively, the gas is further processed for gaseous or liquid fuels, but still on the process of development level. Composition and quality of the gas determine the efficiency of the reactor. A computational model has been developed for the study of reaction kinetics in the gasification rector. The simulation is performed using commercial software Barracuda virtual reactor, VR15. Eulerian-Lagrangian approach in coupling of gas-solid flow has been implemented. Fluid phase is treated with an Eulerian formulation. Discrete phase is treated with a Lagrangian formulation. Particle-particle and particle-wall interactions and inter-phase heat and mass transfer have been taken into account. Series of simulations have been performed to study model prediction of the gas composition. The composition is compared with data from the gasifier at the CHP plant in Güssing, Austria. The model prediction of the composition of gases has good agreements with the result of the operating plant.

  10. Modeling of reaction kinetics in bubbling fluidized bed biomass gasification reactor

    Directory of Open Access Journals (Sweden)

    R.K. Thapa, C. Pfeifer, B. M. Halvorsen

    2014-01-01

    Full Text Available Bubbling fluidized beds are widely used as biomass gasification reactors as at the biomass gasification plant in Güssing, Austria. The reactor in the plant is a dual circulating bubbling fluidized bed gasification reactor. The plant produces 2MW electricity and 4.5MW heat from the gasification of biomass. Wood chips as biomass and olivine particles as hot bed materials are fluidized with high temperature steam in the reactor. As a result, biomass undergoes endothermic chemical reaction to produce a mixture of combustible gases in addition to some carbon-dioxide (CO2. The combustible gases are mainly hydrogen (H2, carbon monoxide (CO and methane (CH4. The gas is used to produce electricity and heat via utilization in a gas engine. Alternatively, the gas is further processed for gaseous or liquid fuels, but still on the process of development level. Composition and quality of the gas determine the efficiency of the reactor. A computational model has been developed for the study of reaction kinetics in the gasification rector. The simulation is performed using commercial software Barracuda virtual reactor, VR15. Eulerian-Lagrangian approach in coupling of gas-solid flow has been implemented. Fluid phase is treated with an Eulerian formulation. Discrete phase is treated with a Lagrangian formulation. Particle-particle and particle-wall interactions and inter-phase heat and mass transfer have been taken into account. Series of simulations have been performed to study model prediction of the gas composition. The composition is compared with data from the gasifier at the CHP plant in Güssing, Austria. The model prediction of the composition of gases has good agreements with the result of the operating plant.

  11. Simulation of Steam Gasification in a Fluidized Bed Reactor with Energy Self-Sufficient Condition

    Directory of Open Access Journals (Sweden)

    Ajaree Suwatthikul

    2017-03-01

    Full Text Available The biomass gasification process is widely accepted as a popular technology to produce fuel for the application in gas turbines and Organic Rankine Cycle (ORC. Chemical reactions of this process can be separated into three reaction zones: pyrolysis, combustion, and reduction. In this study, sensitivity analysis with respect to three input parameters (gasification temperature, equivalence ratio, and steam-to-biomass ratio has been carried out to achieve energy self-sufficient conditions in a steam gasification process under the criteria that the carbon conversion efficiency must be more than 70%, and carbon dioxide gas is lower than 20%. Simulation models of the steam gasification process have been carried out by ASPEN Plus and validated with both experimental data and simulation results from Nikoo & Mahinpey (2008. Gasification temperature of 911 °C, equivalence ratio of 0.18, and a steam-to-biomass ratio of 1.78, are considered as an optimal operation point to achieve energy self-sufficient condition. This operating point gives the maximum of carbon conversion efficiency at 91.03%, and carbon dioxide gas at 15.18 volumetric percentages. In this study, life cycle assessment (LCA is included to compare the environmental performance of conventional and energy self-sufficient gasification for steam biomass gasification.

  12. Oxy-combustion of biomass in a circulating fluidized bed

    Science.gov (United States)

    Kosowska-Golachowska, Monika; Kijo-Kleczkowska, Agnieszka; Luckos, Adam; Wolski, Krzysztof; Musiał, Tomasz

    2016-03-01

    The objective of this study was to investigate combustion characteristics of biomass (willow, Salix viminalis) burnt in air and O2/CO2 mixtures in a circulating fluidized bed (CFB). Air and oxy-combustion characteristics of wooden biomass in CFB were supplemented by the thermogravimetric and differential thermal analyses (TGA/DTA). The results of conducted CFB and TGA tests show that the composition of the oxidizing atmosphere strongly influences the combustion process of biomass fuels. Replacing N2 in the combustion environment by CO2 caused slight delay (higher ignition temperature and lower maximum mass loss rate) in the combustion of wooden biomass. The combustion process in O2/CO2 mixtures at 30% and 40% O2 is faster and shorter than that at lower O2 concentrations.

  13. Oxy-combustion of biomass in a circulating fluidized bed

    Directory of Open Access Journals (Sweden)

    Kosowska-Golachowska Monika

    2016-03-01

    Full Text Available The objective of this study was to investigate combustion characteristics of biomass (willow, Salix viminalis burnt in air and O2/CO2 mixtures in a circulating fluidized bed (CFB. Air and oxy-combustion characteristics of wooden biomass in CFB were supplemented by the thermogravimetric and differential thermal analyses (TGA/DTA. The results of conducted CFB and TGA tests show that the composition of the oxidizing atmosphere strongly influences the combustion process of biomass fuels. Replacing N2 in the combustion environment by CO2 caused slight delay (higher ignition temperature and lower maximum mass loss rate in the combustion of wooden biomass. The combustion process in O2/CO2 mixtures at 30% and 40% O2 is faster and shorter than that at lower O2 concentrations.

  14. Tar Production from Biomass Pyrolysis in a Fluidized Bed Reactor: A Novel Turbulent Multiphase Flow Formulation

    Science.gov (United States)

    Bellan, J.; Lathouwers, D.

    2000-01-01

    A novel multiphase flow model is presented for describing the pyrolysis of biomass in a 'bubbling' fluidized bed reactor. The mixture of biomass and sand in a gaseous flow is conceptualized as a particulate phase composed of two classes interacting with the carrier gaseous flow. The solid biomass is composed of three initial species: cellulose, hemicellulose and lignin. From each of these initial species, two new solid species originate during pyrolysis: an 'active' species and a char, thus totaling seven solid-biomass species. The gas phase is composed of the original carrier gas (steam), tar and gas; the last two species originate from the volumetric pyrolysis reaction. The conservation equations are derived from the Boltzmann equations through ensemble averaging. Stresses in the gaseous phase are the sum of the Newtonian and Reynolds (turbulent) contributions. The particulate phase stresses are the sum of collisional and Reynolds contributions. Heat transfer between phases, and heat transfer between classes in the particulate phase is modeled, the last resulting from collisions between sand and biomass. Closure of the equations must be performed by modeling the Reynolds stresses for both phases. The results of a simplified version (first step) of the model are presented.

  15. Transient behavior of devolatilization and char reaction during steam gasification of biomass.

    Science.gov (United States)

    Moon, Jihong; Lee, Jeungwoo; Lee, Uendo; Hwang, Jungho

    2013-04-01

    Steam gasification of biomass is a promising method for producing high quality syngas for polygeneration. During the steam gasification, devolatilization and char reaction are key steps of syngas production and the contributions of the two reactions are highly related to gasification conditions. In this study, the transient characteristics of devolatilization and char reaction in biomass steam gasification were investigated by monitoring cumulative gas production and composition changes in terms of reaction temperature and S/B ratio. Contribution of each reaction stage on the product gas yield was studied in detail. The results provide important insight for understanding the complex nature of biomass gasification and will guide future improvements to the biomass gasification process. Copyright © 2013 Elsevier Ltd. All rights reserved.

  16. Utilization of CO2 and biomass char derived from pyrolysis of Dunaliella salina: the effects of steam and catalyst on CO and H2 gas production.

    Science.gov (United States)

    Yang, Chao; Jia, Lishan; Su, Shuai; Tian, Zhongbiao; Song, Qianqian; Fang, Weiping; Chen, Changping; Liu, Guangfa

    2012-04-01

    Biomass char, by-product of Dunaliella salina pyrolysis at a final pyrolysis temperature of 500°C, was used as feedstock material in this study. The reactions of biomass char with CO(2) were performed in a fixed-bed reactor to evaluate the effect of temperature and steam on the CO(2) conversion, CO yield and gas composition. The CO(2) conversion and CO yield without steam and catalyst reached about 61.84% and 0.99mol/(mol CO(2)) at 800°C, respectively. Steam and high temperature led to high CO(2) conversion. A new approach for improving H(2) was carried out by using biomass char and Au/Al(2)O(3) catalyst, which combined steam gasification of biomass char and water gas shift reaction, and the H(2) concentration was 1.8 times higher than without catalyst. The process not only mitigated CO(2) emission and made use of residual biomass char, but also created renewable source.

  17. Steam explosion and its combinatorial pretreatment refining technology of plant biomass to bio-based products.

    Science.gov (United States)

    Chen, Hong-Zhang; Liu, Zhi-Hua

    2015-06-01

    Pretreatment is a key unit operation affecting the refinery efficiency of plant biomass. However, the poor efficiency of pretreatment and the lack of basic theory are the main challenges to the industrial implementation of the plant biomass refinery. The purpose of this work is to review steam explosion and its combinatorial pretreatment as a means of overcoming the intrinsic characteristics of plant biomass, including recalcitrance, heterogeneity, multi-composition, and diversity. The main advantages of the selective use of steam explosion and other combinatorial pretreatments across the diversity of raw materials are introduced. Combinatorial pretreatment integrated with other unit operations is proposed as a means to exploit the high-efficiency production of bio-based products from plant biomass. Finally, several pilot- and demonstration-scale operations of the plant biomass refinery are described. Based on the principle of selective function and structure fractionation, and multi-level and directional composition conversion, an integrated process with the combinatorial pretreatments of steam explosion and other pretreatments as the core should be feasible and conform to the plant biomass refinery concept. Combinatorial pretreatments of steam explosion and other pretreatments should be further exploited based on the type and intrinsic characteristics of the plant biomass used, the bio-based products to be made, and the complementarity of the processes.

  18. Energy efficient thermochemical conversion of very wet biomass to biofuels by integration of steam drying, steam electrolysis and gasification

    DEFF Research Database (Denmark)

    Clausen, Lasse Røngaard

    2017-01-01

    A novel system concept is presented for the thermochemical conversion of very wet biomasses such as sewage sludge and manure. The system integrates steam drying, solid oxide electrolysis cells (SOEC) and gasification for the production of synthetic natural gas (SNG). The system is analyzed....... The analysis shows that the total efficiency of the novel system is 69–70% depending on the biomass ash content, while the biomass to SNG energy ratio is 165%, which is near the theoretical maximum because electrolytic hydrogen is supplied to the synthesis gas. It is proposed to combine the novel system...... with an anaerobic digester for conversion of biomasses with high nitrogen content, such as sewage sludge. The organic nitrogen in the sewage sludge will be mineralized in the digester instead of ending up as N2 in the SNG product....

  19. FLUIDIZED BED STEAM REFORMING FOR TREATMENT AND IMMOBILIZATION OF LOW-ACTIVITY WASTE

    Energy Technology Data Exchange (ETDEWEB)

    HEWITT WM

    2011-04-08

    This report is one of four reports written to provide background information regarding immobilization technologies remaining under consideration for supplemental immobilization of Hanford's low-activity waste. This paper provides the reader a general understanding of fluidized bed steam reforming and its possible application to treat and immobilize Hanford low-activity waste.

  20. Bench scale steam explosion pretreatment of acid impregnated elephant grass biomass and its impacts on biomass composition, structure and hydrolysis

    NARCIS (Netherlands)

    Kataria, Rashmi; Mol, Annemerel; Schulten, Els; Happel, Anton; Mussatto, Solange I.

    2017-01-01

    In the present study, an acid mediated steam explosion process was evaluated for pretreatment of elephant grass biomass in a bench scale reactor. Different combinations of H2SO4 concentration, reaction time and temperature (leading to different values of combined severity factor - CSF) were used for

  1. Bench scale steam explosion pretreatment of acid impregnated elephant grass biomass and its impacts on biomass composition, structure and hydrolysis

    NARCIS (Netherlands)

    Kataria, Rashmi; Mol, Annemerel; Schulten, Els; Happel, Anton; Mussatto, Solange I.

    2016-01-01

    In the present study, an acid mediated steam explosion process was evaluated for pretreatment of elephant grass biomass in a bench scale reactor. Different combinations of H2SO4 concentration, reaction time and temperature (leading to different values of combined severity fa

  2. Chemical Looping Combustion of Hematite Ore with Methane and Steam in a Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    Samuel Bayham

    2017-08-01

    Full Text Available Chemical looping combustion is considered an indirect method of oxidizing a carbonaceous fuel, utilizing a metal oxide oxygen carrier to provide oxygen to the fuel. The advantage is the significantly reduced energy penalty for separating out the CO2 for reuse or sequestration in a carbon-constrained world. One of the major issues with chemical looping combustion is the cost of the oxygen carrier. Hematite ore is a proposed oxygen carrier due to its high strength and resistance to mechanical attrition, but its reactivity is rather poor compared to tailored oxygen carriers. This problem is further exacerbated by methane cracking, the subsequent deposition of carbon and the inability to transfer oxygen at a sufficient rate from the core of the particle to the surface for fuel conversion to CO2. Oxygen needs to be readily available at the surface to prevent methane cracking. The purpose of this work was to demonstrate the use of steam to overcome this issue and improve the conversion of the natural gas to CO2, as well as to provide data for computational fluid dynamics (CFD validation. The steam will gasify the deposited carbon to promote the methane conversion. This work studies the performance of hematite ore with methane and steam mixtures in a 5 cm fluidized bed up to approximately 140 kPa. Results show an increased conversion of methane in the presence of steam (from 20–45% without steam to 60–95% up to a certain point, where performance decreases. Adding steam allows the methane conversion to carbon dioxide to be similar to the overall methane conversion; it also helped to prevent carbon accumulation from occurring on the particle. In general, the addition of steam to the feed gas increased the methane conversion. Furthermore, the addition of steam caused the steam methane reforming reaction to form more hydrogen and carbon monoxide at higher steam and methane concentrations, which was not completely converted at higher concentrations and

  3. Steam reforming of propane in a fluidized bed membrane reactor for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Rakib, Mohammad A.; Grace, John R.; Lim, C. Jim; Ghiasi, Bahman [Department of Chemical and Biological Engineering, University of British Columbia, 2360 East Mall, Vancouver BC (Canada); Elnashaie, Said S.E.H. [College of Engineering, Misr University for Science and Technology, Distinguished District, 6th of October Province (Egypt)

    2010-06-15

    Steam reforming of propane was carried out in a fluidized bed membrane reactor to investigate a feedstock other than natural gas for production of pure hydrogen. Close to equilibrium conditions were achieved inside the reactor with fluidized catalyst due to the very fast steam reforming reactions. Use of hydrogen permselective Pd{sub 77}Ag{sub 23} membrane panels to extract pure hydrogen shifted the reaction towards complete conversion of the hydrocarbons, including methane, the key intermediate product. Irreversible propane steam reforming is limited by the reversibility of the steam reforming of this methane. To assess the performance improvement due to pure hydrogen withdrawal, experiments were conducted with one and six membrane panels installed along the height of the reactor. The results indicate that a compact reformer can be achieved for pure hydrogen production for a light hydrocarbon feedstock like propane, at moderate operating temperatures of 475-550 C, with increased hydrogen yield. (author)

  4. Practical achievements on biomass steam gasification in a rotary tubular coiled-downdraft reactor.

    Science.gov (United States)

    Andrew, Renny; Gokak, D T; Sharma, Pankaj; Gupta, Shalini

    2016-12-01

    Today, the impending stringent environmental norms and concerns about the depletion of fossil fuel reserves have added impetus on development of cutting edge technologies for production of alternative fuels from renewable sources, like biomass. The concept of biomass pyro-gasification offers a platform for production of (a) hydrogen, (b) hydrocarbons and (c) value added chemicals, etc. In this context, there exists potential for hydrogen production from biomass by superheated steam gasification. Apart from H2, gaseous products of biomass steam gasification contain CO, CH4 and other hydrocarbons that can be converted to hydrogen through cracking, steam reforming and water gas shift reactions. In the present work, the characteristics of biomass steam gasification in an indigenously designed rotary tubular coiled-downdraft reactor for high value gaseous fuel production from rice husk was studied through a series of experiments. The robust reactor system enhances biomass conversion to gaseous products by improved mass and heat transfer within the system induced by a coiled flow pattern with increased heat transfer area. Also, the system has improved upon the reliability of operation and offered greater continuity of the process and easier control in comparison with a conventional process by making use of an innovative gas cooler assembly and efficient venturi-mixing system for biomass and steam. Subsequently, the effects of reactor temperature, steam-to-biomass ratio and residence time on overall product gas yield and hydrogen yield were investigated. From the experimental results, it can be deduced that an optimum reactor temperature of 750 °C, steam-to-biomass ratio of 2.0 and a residence time of 3.0 min contributed highest gas yield (1.252 Nm(3) kg(-1) moisture-free biomass). Based on the obtained experimental results, a projected potential hydrogen yield of 8.6 wt% of the moisture-free biomass could be achieved, and is also practical for production of

  5. Effects of fungal pretreatment and steam explosion pretreatment on enzymatic saccharification of plant biomass.

    Science.gov (United States)

    Sawada, T; Nakamura, Y; Kobayashi, F; Kuwahara, M; Watanabe, T

    1995-12-20

    The effects of consecutive treatments by a lignin-degrading fungus Phanerochaete chrysosporium and by steam explosion for the enzymatic saccharification of plant biomass were studied experimentally, and the optimal operational conditions for obtaining the maximum saccharification were evaluated. Beech wood-meal was treated by the fungus for 98 days and then by high steam temperatures of 170-230 degrees C with steaming times of 0-10 min. The treatment of the wood-meal by fungus prior to steam explosion enhanced the saccharification of wood-meal. The treated wood-meal was separated into holo-cellulose, water soluble material, methanol soluble lignin, and Klason lignin. The saccharification decreased linearly with the increase in the amount of Klason lignin. It was estimated by the equation for the saccharification of exploded wood-meal expressed as a function of steam temperature and steaming time that the maximum saccharification of wood-meal was obtained by consecutive treatments such as fungal treatment for 28 days and then steam explosion at a steam temperature of 215 degrees C and a steaming time of 6.5 min. (c) 1995 John Wiley & Sons, Inc.

  6. The Production of High Levels of Renewable Natural Gas from Biomass Using Steam Hydrogasification

    OpenAIRE

    Thanmongkhon, Yoothana

    2014-01-01

    Renewable Natural Gas (RNG) has been identified as an important alternative fuel that can help to achieve a number of national goals related to the reduction of fossil fuels and to the reduction in carbon dioxide emission. RNG can be produced from various carbonaceous materials such as biomass and organic wastes via a gasification process. The CE-CERT steam hydrogasification technology combines hydrogen with steam under pressurized conditions to convert a wet feedstock to a methane enriched s...

  7. Investigation of radiative heat transfer in fixed bed biomass furnaces

    Energy Technology Data Exchange (ETDEWEB)

    T. Klason; X.S. Bai; M. Bahador; T.K. Nilsson; B. Sunden [Lund Institute of Technology, Lund (Sweden). Division of Fluid Mechanics

    2008-08-15

    This paper presents an investigation of the radiative heat transfer process in two fixed bed furnaces firing biomass fuels and the performance of several widely used models for calculation of radiative heat transfer in the free-room of fixed bed furnaces. The effective mean grey gas absorption coefficients are calculated using an optimised version of the exponential wide band model (EWBM) based on an optical mean beam length. Fly-ash and char particles are taken into account using Mie scattering. In the investigated updraft small-scale fixed bed furnace radiative transfer carries heat from the bed to the free-room, whereas in the cross-current bed large-scale industry furnace, radiative transfer brings heat from the hot zones in the free-room to the drying zone of the bed. Not all the investigated models can predict these heat transfer trends, and the sensitivity of results to model parameters is fairly different in the two furnaces. In the small-scale furnace, the gas absorption coefficient predicted by using different optical lengths has great impact on the predicted temperature field. In the large-scale furnaces, the predicted temperature field is less sensitive to the optical length. In both furnaces, with the same radiative properties, the low-computational-cost P1 model predicts a temperature field in the free-room similar to that by the more time consuming SLW model. In general, the radiative heat transfer rates to the fuel bed are not very sensitive to the radiative properties, but they are sensitive to the different radiative heat transfer models. For a realistic prediction of the radiative heat transfer rate to the fuel bed or to the walls, more computationally demanding models such as the FGG or SLW models should be used. 37 refs., 7 figs., 2 tabs.

  8. Comparison of multiple steam treatment durations for control of bed bugs (Cimex lectularius L.).

    Science.gov (United States)

    Puckett, Robert T; McDonald, Danny L; Gold, Roger E

    2013-09-01

    The factors contributing to the current resurgence of bed bug Cimex lectularius L. populations across the United States and elsewhere include, among others, the development of resistance to chemical insecticides and population management practices. This has led to the development and attempted refinement of many non-chemical control methods that contribute to an IPM approach to solving the current bed bug population density increase in urban dwellings. One such approach is the use of heat in the form of steam to provide an effective mechanism for controlling localized infestations of bed bugs. The work reported herein was designed to refine our understanding of the duration of bed bug/steam contact necessary to affect mortality of bed bugs in laboratory trials. Beg bug eggs, nymphs and adults were exposed to three steam treatment exposure periods in these trials. Mean percentage mortality of bed bug eggs was 100% (regardless of duration of exposure), and that of nymphs and adults ranged from 88.0 to 94.0%. Survivorship of nymphs and adults in the trials was the result of experimental protocol restrictions that would not usually be associated with actual pest management efforts. The treatment equipment used in these trials is portable and relatively inexpensive and represents a non-chemical means of killing all life stages of bed bugs. While this method would likely be seen as an inefficient means of remediating a mature bed bug infestation within a structure, it does represent a practical component of integrated management of this pest insect. © 2012 Society of Chemical Industry.

  9. Concepts of Emission Reduction in Fluidized Bed Combustion of Biomass

    Directory of Open Access Journals (Sweden)

    Amon Purgar

    2012-01-01

    Full Text Available A status report on fluidized bed technology in Austria is under preparation, in response to the Fluidized Bed Conversion multi-lateral technology initiative of the International Energy Agency. This status report focuses on the current operation of fluidized bed combustors. Combustors have been installed in the following industrial sectors: pulp and paper, biomass heat and power plants, waste-to-energy plants, and communal sewage sludge treatment plants. There are also some small demonstration plants. These plants all have in common that they treat renewable fuel types. In many cases, only bio-fuels are treated. Besides the ability to burn a wide range of low-grade and difficult fuels, fluidized bed combustors have the advantages of low NOX emissions and the possibility of in-process capture of SO2. Various emission reduction concepts for fluidized bed combustors that are typical for their industrial sector are discussed. The discussion of these concepts focuses on NOX, SO2 and dust.

  10. Modelling of dynamics of combustion of biomass in fluidized beds

    Directory of Open Access Journals (Sweden)

    Saastamoinen Jaakko J.

    2004-01-01

    Full Text Available New process concepts in energy production and biofuel, which are much more reactive than coal, call for better controllability of the combustion in circulating fluidized bed boilers. Simplified analysis describing the dynamics of combustion in fluidized bed and circulating fluidized bed boilers is presented. Simple formulas for the estimation of the responses of the burning rate and fuel inventory to changes in fuel feeding are presented. Different changes in the fuel feed, such as an impulse, step change, linear increase and cyclic variation are considered. The dynamics of the burning with a change in the feed rate depends on the fuel reactivity and particle size. The response of a fuel mixture with a wide particle size distribution can be found by summing up the effect of different fuel components and size fractions. Methods to extract reaction parameters form dynamic tests in laboratory scale reactors are discussed. The residence time of fuel particles in the bed and the resulting char inventory in the bed decrease with increasing fuel reactivity and differences between coal and biomass is studied. The char inventory affects the stability of combustion. The effect of char inventory and oscillations in the fuel feed on the oscillation of the flue gas oxygen concentration is studied by model calculation. A trend found by earlier measurements is explained by the model.

  11. Heavy metal characterization of circulating fluidized bed derived biomass ash.

    Science.gov (United States)

    Li, Lianming; Yu, Chunjiang; Bai, Jisong; Wang, Qinhui; Luo, Zhongyang

    2012-09-30

    Although the direct combustion of biomass for energy that applies circulating fluidized bed (CFB) technology is steadily expanding worldwide, only few studies have conducted an environmental assessment of biomass ash thus far. Therefore, this study aims to integrate information on the environmental effects of biomass ash. We investigated the concentration of heavy metal in biomass ash samples (bottom ash, cyclone ash, and filter ash) derived from a CFB boiler that combusted agricultural and forest residues at a biomass power plant (2×12 MW) in China. Ash samples were gathered for the digestion and leaching test. The heavy metal content in the solution and the leachate was studied via an inductively coupled plasma-mass spectrometer and a Malvern Mastersizer 2000 mercury analyzer. Measurements for the chemical composition, particle size distribution, and the surface morphology were carried out. Most of the metals in cyclone ash particles were enriched, whereas Ti and Hg were enriched in filter ash. Residence time contributed most to heavy metal enrichment. Under HJ/T 300 conditions, the heavy metals showed serious leaching characteristics. Under EN 12457-2 conditions, leaching behavior was hardly detected.

  12. Numerical Study of Pyrolysis of Biomass in Fluidized Beds

    Science.gov (United States)

    Bellan, Josette; Lathouwers, Danny

    2003-01-01

    A report presents a numerical-simulation study of pyrolysis of biomass in fluidized-bed reactors, performed by use of the mathematical model described in Model of Fluidized Bed Containing Reacting Solids and Gases (NPO-30163), which appears elsewhere in this issue of NASA Tech Briefs. The purpose of the study was to investigate the effect of various operating conditions on the efficiency of production of condensable tar from biomass. The numerical results indicate that for a fixed particle size, the fluidizing-gas temperature is the foremost parameter that affects the tar yield. For the range of fluidizing-gas temperatures investigated, and under the assumption that the pyrolysis rate exceeds the feed rate, the optimum steady-state tar collection was found to occur at 750 K. In cases in which the assumption was not valid, the optimum temperature for tar collection was found to be only slightly higher. Scaling up of the reactor was found to exert a small negative effect on tar collection at the optimal operating temperature. It is also found that slightly better scaling is obtained by use of shallower fluidized beds with greater fluidization velocities.

  13. Liquid transportation fuels via large-scale fluidised-bed gasification of lignocellulosic biomass

    Energy Technology Data Exchange (ETDEWEB)

    Hannula, I.; Kurkela, E.

    2013-04-15

    With the objective of gaining a better understanding of the system design trade-offs and economics that pertain to biomass-to-liquids processes, 20 individual BTL plant designs were evaluated based on their technical and economic performance. The investigation was focused on gasification-based processes that enable the conversion of biomass to methanol, dimethyl ether, Fischer-Tropsch liquids or synthetic gasoline at a large (300 MWth of biomass) scale. The biomass conversion technology was based on pressurised steam/O2-blown fluidised-bed gasification, followed by hot-gas filtration and catalytic conversion of hydrocarbons and tars. This technology has seen extensive development and demonstration activities in Finland during the recent years and newly generated experimental data has also been used in our simulation models. Our study included conceptual design issues, process descriptions, mass and energy balances and production cost estimates. Several studies exist that discuss the overall efficiency and economics of biomass conversion to transportation liquids, but very few studies have presented a detailed comparison between various syntheses using consistent process designs and uniform cost database. In addition, no studies exist that examine and compare BTL plant designs using the same front-end configuration as described in this work. Our analysis shows that it is possible to produce sustainable low-carbon fuels from lignocellulosic biomass with first-law efficiency in the range of 49.6-66.7% depending on the end-product and process conditions. Production cost estimates were calculated assuming Nth plant economics and without public investment support, CO2 credits or tax assumptions. They are 58-65 euro/MWh for methanol, 58-66 euro/MWh for DME, 64-75 euro/MWh for Fischer-Tropsch liquids and 68-78 euro/MWh for synthetic gasoline. (orig.)

  14. Production of hydrogen from biomass by catalytic steam reforming of fast pyrolysis oil

    Energy Technology Data Exchange (ETDEWEB)

    Czernik, S.; Wang, D.; Chornet, E. [National Renewable Energy Lab., Golden, CO (United States). Center for Renewable Chemical Technologies and Materials

    1998-08-01

    Hydrogen is the prototype of the environmentally cleanest fuel of interest for power generation using fuel cells and for transportation. The thermochemical conversion of biomass to hydrogen can be carried out through two distinct strategies: (a) gasification followed by water-gas shift conversion, and (b) catalytic steam reforming of specific fractions derived from fast pyrolysis and aqueous/steam processes of biomass. This paper presents the latter route that begins with fast pyrolysis of biomass to produce bio-oil. This oil (as a whole or its selected fractions) can be converted to hydrogen via catalytic steam reforming followed by a water-gas shift conversion step. Such a process has been demonstrated at the bench scale using model compounds, poplar oil aqueous fraction, and the whole pyrolysis oil with commercial Ni-based steam reforming catalysts. Hydrogen yields as high as 85% have been obtained. Catalyst initial activity can be recovered through regeneration cycles by steam or CO{sub 2} gasification of carbonaceous deposits.

  15. Biomass ash - bed material interactions leading to agglomeration in fluidised bed combustion and gasification

    Energy Technology Data Exchange (ETDEWEB)

    Visser, H.J.M.; Hofmans, H.; Huijnen, R.; Kastelein, R.; Kiel, J.H.A. [ECN Biomass, Petten (Netherlands)

    2000-07-01

    The present study has been aimed at improving the fundamental understanding of mechanisms underlying agglomeration and defluidisation in fluidised bed combustion and gasification of biomass and waste. To this purpose dedicated lab-scale static heating and fluidisation experiments have been conducted with carefully selected and prepared ashes and bed materials, viz. straw ash/sand and willow ash/sand mixtures, mullite subjected to straw gasification and artificially coated mullite. The main conclusion is that ash/bed material interaction processes are very important and often determine the bed agglomeration and defluidisation tendency. In the static heating experiments with both ash/sand mixtures, partial melting-segregation of ash components and dissolution/reaction with the bed material are processes that determine the melt composition. This melt composition and behaviour can deviate considerably form expectations based on ash-only data. Artificially coated bed materials prove to be very useful for systematic studies on the influence of coating composition and thickness on agglomeration tendency. For the coated mullite samples, different stages in the defluidisation process are identified and the influence of coating properties (thickness, composition, morphology) and operating parameters is elucidated. The behaviour of the mullite appears to be dominated by a remnant glass phase. On the one hand, this glass phase accounts for an alkali-getter capability, while on the other hand it is mainly responsible for agglomeration at temperatures {>=} 800C. 3 refs.

  16. Chaos Transfer in Fluidized Beds Accompanied with Biomass Pyrolysis

    Institute of Scientific and Technical Information of China (English)

    唐松涛; 李定凯; 吕子安; 沈幼庭

    2003-01-01

    Experiments of biomass pyrolysis were carried out in a fiuidized bed, and dynamic signals of pressure and temperature were recorded. Correlation dimension was employed to characterize the chaotic behavior of pressure and temperature signals. Both pressure and temperature signals exhibit chaotic behavior, and the chaotic behavior of temperature signals is always weaker than that of pressure signals. Chaos transfer theory was advanced to explain the above phenomena. The discussion on the algorithm of the correlation dimension shows that the distance definition based on rhombic neighborhood is a better choice than the traditional one based on spherical neighborhood. The former provides a satisfactory result in a much shorter time.

  17. Study of a 30 MW bubbling fluidized bed combustor based on co-firing biomass and coal

    Indian Academy of Sciences (India)

    Hemant Kumar; S K Mohapatra; Ravi Inder Singh

    2015-06-01

    Today’s power generation sources are largely dependent on fossil fuels due to which the future sustainable development has become a challenge. A significant amount of the pollutant emissions such as carbon dioxide, carbon monoxide and nitrogen oxide from the power sector is related to the use of fossil fuels for power generation. As the demand for electricity is growing rapidly, emissions of carbon dioxide and other pollutants from this sector can be expected to increase unless other alternatives are made available. Among the energy sources that can substitute fossil fuels, biomass fuels appear as one of the options with a high worldwide potential. In the Punjab region of India, Fluidized-bed combustion technology is being used for converting biomass into thermal energy and power generation in various small scale units. The investigation of biomass-based plant through experimental activities and numerical simulation is the scope of this study. The investigations were done at Captive Power Plant (CPP), Ambuja Cement Limited, a project of Holcim, District Ropar, India. During experimental investigations, the study of bed temperatures and steam temperatures at different zones has been done for coal fired and biomass fired combustors with 30% share. No clear effects of co-firing on boiler performance are observed. However, the operational behavior of the boiler in terms of bed temperature and stack emissions shows a different trend. During simulation, the contours of temperature have been obtained for both the boilers and the trends are found in agreement with real process.

  18. Lignite air-steam gasification in the fluidized bed of iron-containing slag catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kuznetsov, B.N.; Shchipko, M.L.; Golovin, Yu. [Inst. of Chemistry of Natural Organic Materials, Academgorodok, Krasnoyarsk (Russian Federation)

    1995-12-01

    The influence of fluidized bed of iron-containing slag particles on air-steam gasification of powdered Kansk-Achinsk lignite in entrained flow was studied in pilot installation with productivity about 60 kg per hour. Slag of Martin process and boiler slag were used as catalytic active materials until their complete mechanical attrition. Two following methods of catalytic gasification of lignite were compared: the partial gasification in stationary fluidized bed of slag particles with degree of fuel conversion 40-70% and complete gasification in circulating bed of slag particles. In the first case only the most reactive part of fuel is gasified with the simultaneously formation of porous carbon residue with good sorption ability. It was found the catalytic fluidized bed improves heat transfer from combustion to reduction zone of gas-generator and increases the rate of fuel conversion at the temperature range 900-1000{degrees}C. At these temperatures the degree of conversion is depended considerably on the duration time of fuel particles in the catalytic fluidized bed. The influence of catalytic fluidized bed height and velocity of reaction mixture on the temperature profiles in the gas-generator was studied. The optimal relationship was found between the fluidized bed height and velocity of flow which makes possible to produce the gas with higher calorific value at maximum degree of fuel conversion.

  19. Development of Ni-Based Catalysts for Steam Reforming of Tar Derived from Biomass Pyrolysis

    Institute of Scientific and Technical Information of China (English)

    Dalin LI; Yoshinao NAKAGAWA; Keiichi TOMISHIGE

    2012-01-01

    Nickel catalysts are effective for the steam reforming of tar derived from biomass pyrolysis,but the improvement is needed in terms of activity,stability,suppression of coke deposition and aggregation,and regeneration.Our recent development of Ni-based catalysts for the steam reforming of tar is reviewed including the modification with CeO2 (or MnO),trace Pt,and MgO.The role of additives such as CeO2,MnO,Pt,and MgO is also discussed.

  20. Investigations on a new internally-heated tubular packed-bed methanol–steam reformer

    KAUST Repository

    Nehe, Prashant

    2015-05-01

    Small-scale reformers for hydrogen production through steam reforming of methanol can provide an alternative solution to the demand of continuous supply of hydrogen gas for the operation of Proton Exchange Membrane Fuel Cells (PEMFCs). A packed-bed type reformer is one of the potential designs for such purpose. An externally heated reformer has issues of adverse lower temperature in the core of the reformer and significant heat loss to the environment thus impacting its performance. Experimental and numerical studies on a new concept of internally heated tubular packed-bed methanol-steam reformer have been reported in this paper with improved performance in terms of higher methanol conversion and reduced heat losses to surroundings. CuO/ZnO/Al2O3 is used as the catalyst for the methanol-steam reforming reaction and a rod-type electric heater at the center of the reactor is used for supplying necessary heat for endothermic steam reforming reaction. The vaporizer and the reformer unit with a constant volume catalyst bed are integrated in the annular section of a tubular reformer unit. The performance of the reformer was investigated at various operating conditions like feed rate of water-methanol mixture, mass of the catalyst and reforming temperature. The experimental and numerical results show that the methanol conversion and CO concentration increase with internal heating for a wide range of operating conditions. The developed reformer unit generates 50-80W (based on lower heating value) of hydrogen gas for applications in PEMFCs. For optimized design and operating conditions, the reformer unit produced 298sccm reformed gas containing 70% H2, 27% CO2 and 3% CO at 200-240°C which can produce a power output of 25-32W assuming 60% fuel cell efficiency and 80% of hydrogen utilization in a PEMFC. © 2015 Hydrogen Energy Publications, LLC.

  1. Evaluation of Hybrid Power Plants using Biomass, Photovoltaics and Steam Electrolysis for Hydrogen and Power Generation

    Science.gov (United States)

    Petrakopoulou, F.; Sanz, J.

    2014-12-01

    Steam electrolysis is a promising process of large-scale centralized hydrogen production, while it is also considered an excellent option for the efficient use of renewable solar and geothermal energy resources. This work studies the operation of an intermediate temperature steam electrolyzer (ITSE) and its incorporation into hybrid power plants that include biomass combustion and photovoltaic panels (PV). The plants generate both electricity and hydrogen. The reference -biomass- power plant and four variations of a hybrid biomass-PV incorporating the reference biomass plant and the ITSE are simulated and evaluated using exergetic analysis. The variations of the hybrid power plants are associated with (1) the air recirculation from the electrolyzer to the biomass power plant, (2) the elimination of the sweep gas of the electrolyzer, (3) the replacement of two electric heaters with gas/gas heat exchangers, and (4) the replacement two heat exchangers of the reference electrolyzer unit with one heat exchanger that uses steam from the biomass power plant. In all cases, 60% of the electricity required in the electrolyzer is covered by the biomass plant and 40% by the photovoltaic panels. When comparing the hybrid plants with the reference biomass power plant that has identical operation and structure as that incorporated in the hybrid plants, we observe an efficiency decrease that varies depending on the scenario. The efficiency decrease stems mainly from the low effectiveness of the photovoltaic panels (14.4%). When comparing the hybrid scenarios, we see that the elimination of the sweep gas decreases the power consumption due to the elimination of the compressor used to cover the pressure losses of the filter, the heat exchangers and the electrolyzer. Nevertheless, if the sweep gas is used to preheat the air entering the boiler of the biomass power plant, the efficiency of the plant increases. When replacing the electric heaters with gas-gas heat exchangers, the

  2. A novel reforming method for hydrogen production from biomass steam gasification.

    Science.gov (United States)

    Gao, Ningbo; Li, Aimin; Quan, Cui

    2009-09-01

    In this work, an experimental study of biomass gasification in different operation conditions has been carried out in an updraft gasifier combined with a porous ceramic reformer. The effects of gasifier temperature, steam to biomass ratio (S/B), and reforming temperature on the gas characteristic parameters were investigated with and without porous ceramic filled in reformer. The results indicated that considerable synergistics effects were observed as the porous ceramic was filled in reformer leading to an increase in the hydrogen production. With the increasing gasifier temperature varying from 800 to 950 degrees C, hydrogen yield increased from 49.97 to 79.91 g H(2)/kg biomass. Steam/biomass ratio of 2.05 seemed to be optimal in all steam-gasification runs. The effect of reforming temperature for water-soluble tar produced in porous ceramic reforming was also investigated, and it was found that the conversion ratio of total organic carbon (TOC) contents is between 71.08% and 75.74%.

  3. Biomass gasification in a circulating fluidized bed; Vergasung von Biomasse in der zirkulierenden Wirbelschicht

    Energy Technology Data Exchange (ETDEWEB)

    Ising, M.; Hoelder, D.; Backhaus, C.; Althaus, W. [Fraunhofer Inst. fuer Umwelt-, Sicherheits- und Energietechnik UMSICHT, Oberhausen (Germany)

    1998-09-01

    Biomass gasification in a circulating fluidized bed, in combination with a gas engine or gas burner, is a promising option for energetic use of biomass. Economic efficiency analyses on the basis of the UMSICHT plant show that this technology for combined heat and power generation from biomass is promising also for the range below 10 MW. The economic situation of any plant must be considered for the specific boundary conditions imposed by the power supply industry. The feasibility of the process was tested in a demonstration plant at Oberhausen. The plant was optimized further in extensive test series, and a number of tar reduction processes were investigated and improved on. The authors now intend to prove that gasification in a circulating fluidized bed combined with a gas engine cogeneration plant is feasible in continuous operation. (orig./SR) [Deutsch] Die Vergasung von Biomasse in der zirkulierenden Wirbelschicht ist in Kombination mit einem Gasmotor oder einem Gasbrenner eine vielversprechende Option fuer die energetische Biomassenutzung. Wirtschaftlichkeitsbetrachtungen auf Basis der UMSICHT-Anlage zeigen, dass diese Technologie fuer die gekoppelte Strom- und Waermeerzeugung aus Biomasse auch im Leistungsbereich unter 10 MW grosse Chancen verspricht. Dabei ist die oekonomische Situation einer Anlage im Einzelfall unter Beachtung der energiewirtschaftlichen Randbedingungen zu beurteilen. Durch den Betrieb einer Demonstrationsanlage in Oberhausen konnte die Funktion des Verfahrens nachgewiesen werden. In weiteren umfangreichen Versuchsreihen werden die Anlage weiter optimiert und verschiedene Konzepte zur Teerminderung untersucht und weiterentwickelt. Angestrebt ist der Nachweis des Dauerbetriebs von ZWS-Vergasung zusammen mit dem Gasmotoren-BHKW. (orig./SR)

  4. LIQUID BIO-FUEL PRODUCTION FROM NON-FOOD BIOMASS VIA HIGH TEMPERATURE STEAM ELECTROLYSIS

    Energy Technology Data Exchange (ETDEWEB)

    G. L. Hawkes; J. E. O' Brien; M. G. McKellar

    2011-11-01

    Bio-Syntrolysis is a hybrid energy process that enables production of synthetic liquid fuels that are compatible with the existing conventional liquid transportation fuels infrastructure. Using biomass as a renewable carbon source, and supplemental hydrogen from high-temperature steam electrolysis (HTSE), bio-syntrolysis has the potential to provide a significant alternative petroleum source that could reduce US dependence on imported oil. Combining hydrogen from HTSE with CO from an oxygen-blown biomass gasifier yields syngas to be used as a feedstock for synthesis of liquid transportation fuels via a Fischer-Tropsch process. Conversion of syngas to liquid hydrocarbon fuels, using a biomass-based carbon source, expands the application of renewable energy beyond the grid to include transportation fuels. It can also contribute to grid stability associated with non-dispatchable power generation. The use of supplemental hydrogen from HTSE enables greater than 90% utilization of the biomass carbon content which is about 2.5 times higher than carbon utilization associated with traditional cellulosic ethanol production. If the electrical power source needed for HTSE is based on nuclear or renewable energy, the process is carbon neutral. INL has demonstrated improved biomass processing prior to gasification. Recyclable biomass in the form of crop residue or energy crops would serve as the feedstock for this process. A process model of syngas production using high temperature electrolysis and biomass gasification is presented. Process heat from the biomass gasifier is used to heat steam for the hydrogen production via the high temperature steam electrolysis process. Oxygen produced form the electrolysis process is used to control the oxidation rate in the oxygen-blown biomass gasifier. Based on the gasifier temperature, 94% to 95% of the carbon in the biomass becomes carbon monoxide in the syngas (carbon monoxide and hydrogen). Assuming the thermal efficiency of the power

  5. LIQUID BIO-FUEL PRODUCTION FROM NON-FOOD BIOMASS VIA HIGH TEMPERATURE STEAM ELECTROLYSIS

    Energy Technology Data Exchange (ETDEWEB)

    G. L. Hawkes; J. E. O' Brien; M. G. McKellar

    2011-11-01

    Bio-Syntrolysis is a hybrid energy process that enables production of synthetic liquid fuels that are compatible with the existing conventional liquid transportation fuels infrastructure. Using biomass as a renewable carbon source, and supplemental hydrogen from high-temperature steam electrolysis (HTSE), bio-syntrolysis has the potential to provide a significant alternative petroleum source that could reduce US dependence on imported oil. Combining hydrogen from HTSE with CO from an oxygen-blown biomass gasifier yields syngas to be used as a feedstock for synthesis of liquid transportation fuels via a Fischer-Tropsch process. Conversion of syngas to liquid hydrocarbon fuels, using a biomass-based carbon source, expands the application of renewable energy beyond the grid to include transportation fuels. It can also contribute to grid stability associated with non-dispatchable power generation. The use of supplemental hydrogen from HTSE enables greater than 90% utilization of the biomass carbon content which is about 2.5 times higher than carbon utilization associated with traditional cellulosic ethanol production. If the electrical power source needed for HTSE is based on nuclear or renewable energy, the process is carbon neutral. INL has demonstrated improved biomass processing prior to gasification. Recyclable biomass in the form of crop residue or energy crops would serve as the feedstock for this process. A process model of syngas production using high temperature electrolysis and biomass gasification is presented. Process heat from the biomass gasifier is used to heat steam for the hydrogen production via the high temperature steam electrolysis process. Oxygen produced form the electrolysis process is used to control the oxidation rate in the oxygen-blown biomass gasifier. Based on the gasifier temperature, 94% to 95% of the carbon in the biomass becomes carbon monoxide in the syngas (carbon monoxide and hydrogen). Assuming the thermal efficiency of the power

  6. Research into Biomass and Waste Gasification in Atmospheric Fluidized Bed

    Energy Technology Data Exchange (ETDEWEB)

    Skala, Zdenek; Ochrana, Ladislav; Lisy, Martin; Balas, Marek; Kohout, Premysl; Skoblja, Sergej

    2007-07-01

    Considerable attention is paid in the Czech Republic to renewable energy sources. The largest potential, out of them all, have biomass and waste. The aim therefore is to use them in CHP in smaller units (up to 5MWel). These are the subject of the research summarized in our article. The paper presents results of experimental research into gasification in a 100 kW AFB gasifier situated in Energy Institute, Faculty of Mechanical Engineering, Brno University of Technology, and fitted with gas cleaning equipment. Within the research, study was carried out into gas cleaning taking primary measures in the fluidized bed and using hot filter, metal-based catalytic filter, and wet scrubber. Descriptions and diagrams are given of the gasifier and new ways of cleaning. Results include: Impact of various fuels (farming and forest wastes and fast-growing woods and culm plants) on fuel gas quality. Individual kinds of biomass have very different thermal and physical properties; Efficiency of a variety of cleaning methods on content of dust and tars and comparison of these methods; and, Impact of gasifier process parameters on resultant gas quality. (auth)

  7. Metal catalysts for steam reforming of tar derived from the gasification of lignocellulosic biomass.

    Science.gov (United States)

    Li, Dalin; Tamura, Masazumi; Nakagawa, Yoshinao; Tomishige, Keiichi

    2015-02-01

    Biomass gasification is one of the most important technologies for the conversion of biomass to electricity, fuels, and chemicals. The main obstacle preventing the commercial application of this technology is the presence of tar in the product gas. Catalytic reforming of tar appears a promising approach to remove tar and supported metal catalysts are among the most effective catalysts. Nevertheless, improvement of catalytic performances including activity, stability, resistance to coke deposition and aggregation of metal particles, as well as catalyst regenerability is greatly needed. This review focuses on the design and catalysis of supported metal catalysts for the removal of tar in the gasification of biomass. The recent development of metal catalysts including Rh, Ni, Co, and their alloys for steam reforming of biomass tar and tar model compounds is introduced. The role of metal species, support materials, promoters, and their interfaces is described.

  8. Steam generation unit in a simple version of biomass based small cogeneration unit

    OpenAIRE

    Sornek Krzysztof; Filipowicz Mariusz; Szubel Mateusz; Bożek Estera; Izdebski Krzysztof

    2014-01-01

    The organic Rankine cycle (ORC) is a very promising process for the conversion of low or medium temperature heat to electricity in small and micro scale biomass powered systems. Classic ORC is analogous to Clausius–Rankine cycle in a steam power plant, but instead of water it uses low boiling, organic working fluids. Seeking energy and economical optimization of biomass-based ORC systems, we have proposed some modifications e.g. in low boiling fluid circuit construction. Due to the fact that ...

  9. Evaluation of storage methods for the conversion of corn stover biomass to sugars based on steam explosion pretreatment.

    Science.gov (United States)

    Liu, Zhi-Hua; Qin, Lei; Jin, Ming-Jie; Pang, Feng; Li, Bing-Zhi; Kang, Yong; Dale, Bruce E; Yuan, Ying-Jin

    2013-03-01

    Effects of dry and wet storage methods without or with shredding on the conversion of corn stover biomass were investigated using steam explosion pretreatment and enzymatic hydrolysis. Sugar conversions and yields for wet stored biomass were obviously higher than those for dry stored biomass. Shredding reduced sugar conversions compared with non-shredding, but increased sugar yields. Glucan conversion and glucose yield for non-shredded wet stored biomass reached 91.5% and 87.6% after 3-month storage, respectively. Data of micro-structure and crystallinity of biomass indicated that corn stover biomass maintained the flexible and porous structure after wet storage, and hence led to the high permeability of corn stover biomass and the high efficiency of pretreatment and hydrolysis. Therefore, the wet storage methods would be desirable for the conversion of corn stover biomass to fermentable sugars based on steam explosion pretreatment and enzymatic hydrolysis.

  10. Steam gasification of acid-hydrolysis biomass CAHR for clean syngas production.

    Science.gov (United States)

    Chen, Guanyi; Yao, Jingang; Yang, Huijun; Yan, Beibei; Chen, Hong

    2015-03-01

    Main characteristics of gaseous product from steam gasification of acid-hydrolysis biomass CAHR have been investigated experimentally. The comparison in terms of evolution of syngas flow rate, syngas quality and apparent thermal efficiency was made between steam gasification and pyrolysis in the lab-scale apparatus. The aim of this study was to determine the effects of temperature and steam to CAHR ratio on gas quality, syngas yield and energy conversion. The results showed that syngas and energy yield were better with gasification compared to pyrolysis under identical thermal conditions. Both high gasification temperature and introduction of proper steam led to higher gas quality, higher syngas yield and higher energy conversion efficiency. However, excessive steam reduced hydrogen yield and energy conversion efficiency. The optimal value of S/B was found to be 3.3. The maximum value of energy ratio was 0.855 at 800°C with the optimal S/B value. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Fluidized bed membrane reactor for hydrogen production by steam reforming of higher hydrocarbons

    Energy Technology Data Exchange (ETDEWEB)

    Rakib, M.A.; Grace, J.R.; Lim, C.J. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Chemical and Biological Engineering; Elnashaie, S.S.E.H. [Pennsylvania State Univ., Harrisburg, PA (United States). Environmental and Sustainable Engineering; Bolkan, Y.G. [Calgary Univ., AB (Canada). Dept. of Chemical and Petroleum Engineering

    2007-07-01

    Hydrogen is an an environment friendly fuel that has many applications such as a carbon-free fuel, and as a fuel for hydrogen fuel cells for automotive and other applications. It can be converted into useful forms of energy in many ways and has been used effectively in a number of internal combustion engine vehicles mixed with natural gas (hythane), and in a growing number of fuel cell vehicles. It can also be combined with oxygen without combustion in an electrochemical reaction to produce direct-current electricity in fuel cells. As the demand of hydrogen is projected to increase, research is being conducted into ways of improving hydrogen production, separation, purification and storage. This paper presented the results of a study that investigated modeling of a fluidized bed membrane reactor for steam reforming of higher hydrocarbons, in order to get the sizing of an experimental reformer setup. In the simulations, n-heptane was used as a model compound to represent steam reforming of naphtha. The reformer was modeled as a bubbling fluidized bed reactor, consisting of two pseudo phases, a dense phase and a bubble phase, both in plug flow. The paper discussed the irreversibility of steam reforming of higher hydrocarbons, kinetic modeling of a fluidized bed membrane reactor, and presented the model assumptions. Model equations for the reaction side and the separator side as well as the interphase mass exchange coefficient were provided. It was concluded that challenges specific to higher hydrocarbons included catalyst deactivation and possible membrane fouling. 26 refs., 1 tab., 9 figs., 1 appendix.

  12. Mathematical Modelling of the Fixed-Bed Biomass-Coal Co-Gasification Process

    Directory of Open Access Journals (Sweden)

    Donskoy Igor G.

    2016-01-01

    Full Text Available The paper considers mathematical modelling of downdraft fixed-bed gasification process of the mixtures of woody biomass and coal. Biomass/coal ratio, biomass moisture content and air equivalence ratio are varying parameters. Boundaries of the efficient gasification regimes are estimated.

  13. Lignocellulosic biomass-Thermal pretreatment with steam: Pretreatment techniques for biofuels and biorefineries

    DEFF Research Database (Denmark)

    Toor, Saqib; Rosendahl, Lasse; Hoffmann, Jessica

    2013-01-01

    With the ever rising demand for more energy and the limited availability of depleted world resources, many are beginning to look for alternatives to fossil fuels. Liquid biofuel, in particular, is of key interest to decrease our dependency on fuels produced from imported petroleum. Biomass pre...... technologies; thermal pre-treatment with steam. The Norwegian company CAMBI developed a process for treatment of sludge from waste water treatment plants, and the idea was based on the experience that cooking sludge under pressure at temperature from 150oC to 180oC improved the digestibility and at the same...... time increased the dewaterability of the sludge. If CAMBI’s process is to be used for treatment of biomass, it will have to compete with other processes on market. The strongest competitor art present is the IBUS (Integrated Biomass Utilization System) process of DONG INBICON which is used for pre...

  14. Steam generation unit in a simple version of biomass based small cogeneration unit

    Directory of Open Access Journals (Sweden)

    Sornek Krzysztof

    2014-01-01

    Full Text Available The organic Rankine cycle (ORC is a very promising process for the conversion of low or medium temperature heat to electricity in small and micro scale biomass powered systems. Classic ORC is analogous to Clausius–Rankine cycle in a steam power plant, but instead of water it uses low boiling, organic working fluids. Seeking energy and economical optimization of biomass-based ORC systems, we have proposed some modifications e.g. in low boiling fluid circuit construction. Due to the fact that the operation of a micro steam turbine is rather inefficient from the technical and economic point of view, a specially modified air compressor can be used as a steam piston engine. Such engine should be designed to work at low pressure of the working medium. Studies regarding the first version of the prototype installation were focused on the confirmation of applicability of a straw boiler in the prototype ORC power system. The results of the previous studies and the studies described in the paper (on the new cogeneration unit confirmed the high potential of the developed solution. Of course, many further studies have to be carried out.

  15. Biomass Steam Gasification with In-Situ CO2 Capture for Enriched Hydrogen Gas Production: A Reaction Kinetics Modelling Approach

    Directory of Open Access Journals (Sweden)

    Mohamed Ibrahim Abdul Mutalib

    2010-08-01

    Full Text Available Due to energy and environmental issues, hydrogen has become a more attractive clean fuel. Furthermore, there is high interest in producing hydrogen from biomass with a view to sustainability. The thermochemical process for hydrogen production, i.e. gasification, is the focus of this work. This paper discusses the mathematical modeling of hydrogen production process via biomass steam gasification with calcium oxide as sorbent in a gasifier. A modelling framework consisting of kinetics models for char gasification, methanation, Boudouard, methane reforming, water gas shift and carbonation reactions to represent the gasification and CO2 adsorption in the gasifier, is developed and implemented in MATLAB. The scope of the work includes an investigation of the influence of the temperature, steam/biomass ratio and sorbent/biomass ratio on the amount of hydrogen produced, product gas compositions and carbon conversion. The importance of different reactions involved in the process is also discussed. It is observed that hydrogen production and carbon conversion increase with increasing temperature and steam/biomass ratio. The model predicts a maximum hydrogen mole fraction in the product gas of 0.81 occurring at 950 K, steam/biomass ratio of 3.0 and sorbent/biomass ratio of 1.0. In addition, at sorbent/biomass ratio of 1.52, purity of H2 can be increased to 0.98 mole fraction with all CO2 present in the system adsorbed.

  16. Assessment of the technical and economic potentials of biomass use for the production of steam, chemicals and polymers

    NARCIS (Netherlands)

    Saygin, D.; Gielen, D. J.; Draeck, M.; Worrell, E.; Patel, M. K.

    2014-01-01

    Fossil fuel substitution with biomass is one of the measures to reduce carbon dioxide (CO2) emissions. This paper estimates the cost-effectiveness of raising industrial steam and producing materials (i.e. chemicals, polymers) from biomass. We quantify their long-term global potentials in terms of en

  17. Assessment of the technical and economic potentials of biomass use for the production of steam, chemicals and polymers

    NARCIS (Netherlands)

    Saygin, D.; Gielen, D. J.; Draeck, M.; Worrell, E.|info:eu-repo/dai/nl/106856715; Patel, M. K.

    2014-01-01

    Fossil fuel substitution with biomass is one of the measures to reduce carbon dioxide (CO2) emissions. This paper estimates the cost-effectiveness of raising industrial steam and producing materials (i.e. chemicals, polymers) from biomass. We quantify their long-term global potentials in terms of

  18. Investigation on the reactions influencing biomass air and air/steam gasification for hydrogen production

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, J.F.; Roman, S.; Bragado, D. [Departamento de Fisica Aplicada, University of Extremadura, 06071 (Spain); Calderon, M. [Departamento de Electronica e Ingenieria Electromecanica, University of Extremadura, 06071 (Spain)

    2008-08-15

    Hydrogen could be the energy carrier of the next world scene provided that its production, transportation and storage are solved. In this work the production of an hydrogen-rich gas by air/steam and air gasification of olive oil waste was investigated. The study was carried out in a laboratory reactor at atmospheric pressure over a temperature range of 700 - 900 C using a steam/biomass ratio of 1.2 w/w. The influence of the catalysts ZnCl{sub 2} and dolomite was also studied at 800 and 900 C. The solid, energy and carbon yield (%), gas molar composition and high heating value of the gas (kJ NL{sup -} {sup 1}), were determined for all cases and the differences between the gasification process with and without steam were established. Also, this work studies the different equilibria taking place, their predominance in each process and how the variables considered affect the final gas hydrogen concentration. The results obtained suggest that the operating conditions were optimized at 900 C in steam gasification (a hydrogen molar fraction of 0.70 was obtained at a residence time of 7 min). The use of both catalysts resulted positive at 800 C, especially in the case of ZnCl{sub 2} (attaining a H{sub 2} molar fraction of 0.69 at a residence time of 5 min). (author)

  19. An Experimental Investigation of Hydrogen Production from Biomass

    Institute of Scientific and Technical Information of China (English)

    吕鹏梅; 常杰; 付严; 王铁军; 陈勇; 祝京旭

    2003-01-01

    In gaseous products of biomass steam gasification, there exist a lot of CO, CH4 and other hydrocarbons that can be converted to hydrogen through steam reforming reactions. There exists potential hydrogen production from the raw gas of biomass steam gasification. In the present work, the characteristics of hydrogen production from biomass steam gasification were investigated in a small-scale fluidized bed. In these experiments, the gasifying agent (air) was supplied into the reactor from the bottom of the reactor and the steam was added into the reactor above biomass feeding location. The effects of reaction temperature, steam to biomass ratio, equivalence ratio (ER) and biomass particle size on hydrogen yield and hydrogen yield potential were investigated. The experimental results showed that higher reactor temperature, proper ER, proper steam to biomass ratio and smaller biomass particle size will contribute to more hydrogen and potential hydrogen yield.

  20. Artificial neural network models for biomass gasification in fluidized bed gasifiers

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Hernández, J. Alfredo; Bruno, Joan Carles

    2013-01-01

    bed gasifier can be successfully predicted by applying neural networks. ANNs models use in the input layer the biomass composition and few operating parameters, two neurons in the hidden layer and the backpropagation algorithm. The results obtained by these ANNs show high agreement with published......Artificial neural networks (ANNs) have been applied for modeling biomass gasification process in fluidized bed reactors. Two architectures of ANNs models are presented; one for circulating fluidized bed gasifiers (CFB) and the other for bubbling fluidized bed gasifiers (BFB). Both models determine...

  1. Catalytic Steam Reforming of Toluene as a Model Compound of Biomass Gasification Tar Using Ni-CeO2/SBA-15 Catalysts

    Directory of Open Access Journals (Sweden)

    Erik Dahlquist

    2013-07-01

    Full Text Available Nickel supported on SBA-15 doped with CeO2 catalysts (Ni-CeO2/SBA-15 was prepared, and used for steam reforming of toluene which was selected as a model compound of biomass gasification tar. A fixed-bed lab-scale set was designed and employed to evaluate the catalytic performances of the Ni-CeO2/SBA-15 catalysts. Experiments were performed to reveal the effects of several factors on the toluene conversion and product gas composition, including the reaction temperature, steam/carbon (S/C ratio, and CeO2 loading content. Moreover, the catalysts were subjected to analysis of their carbon contents after the steam reforming experiments, as well as to test the catalytic stability over a long experimental period. The results indicated that the Ni-CeO2/SBA-15 catalysts exhibited promising capabilities on the toluene conversion, anti-coke deposition and catalytic stability. The toluene conversion reached as high as 98.9% at steam reforming temperature of 850 °C and S/C ratio of 3 using the Ni-CeO2(3wt%/SBA-15 catalyst. Negligible coke formation was detected on the used catalyst. The gaseous products mainly consisted of H2 and CO, together with a little CO2 and CH4.

  2. A CFD model for biomass combustion in a packed bed furnace

    Energy Technology Data Exchange (ETDEWEB)

    Karim, Md. Rezwanul [Faculty of Science, Engineering and Technology, Swinburne University of Technology, VIC 3122 (Australia); Department of Mechanical & Chemical Engineering, Islamic University of Technology, Gazipur 1704 (Bangladesh); Ovi, Ifat Rabbil Qudrat [Department of Mechanical & Chemical Engineering, Islamic University of Technology, Gazipur 1704 (Bangladesh); Naser, Jamal, E-mail: jnaser@swin.edu.au [Faculty of Science, Engineering and Technology, Swinburne University of Technology, VIC 3122 (Australia)

    2016-07-12

    Climate change has now become an important issue which is affecting environment and people around the world. Global warming is the main reason of climate change which is increasing day by day due to the growing demand of energy in developed countries. Use of renewable energy is now an established technique to decrease the adverse effect of global warming. Biomass is a widely accessible renewable energy source which reduces CO{sub 2} emissions for producing thermal energy or electricity. But the combustion of biomass is complex due its large variations and physical structures. Packed bed or fixed bed combustion is the most common method for the energy conversion of biomass. Experimental investigation of packed bed biomass combustion is difficult as the data collection inside the bed is challenging. CFD simulation of these combustion systems can be helpful to investigate different operational conditions and to evaluate the local values inside the investigation area. Available CFD codes can model the gas phase combustion but it can’t model the solid phase of biomass conversion. In this work, a complete three-dimensional CFD model is presented for numerical investigation of packed bed biomass combustion. The model describes the solid phase along with the interface between solid and gas phase. It also includes the bed shrinkage due to the continuous movement of the bed during solid fuel combustion. Several variables are employed to represent different parameters of solid mass. Packed bed is considered as a porous bed and User Defined Functions (UDFs) platform is used to introduce solid phase user defined variables in the CFD. Modified standard discrete transfer radiation method (DTRM) is applied to model the radiation heat transfer. Preliminary results of gas phase velocity and pressure drop over packed bed have been shown. The model can be useful for investigation of movement of the packed bed during solid fuel combustion.

  3. A CFD model for biomass combustion in a packed bed furnace

    Science.gov (United States)

    Karim, Md. Rezwanul; Ovi, Ifat Rabbil Qudrat; Naser, Jamal

    2016-07-01

    Climate change has now become an important issue which is affecting environment and people around the world. Global warming is the main reason of climate change which is increasing day by day due to the growing demand of energy in developed countries. Use of renewable energy is now an established technique to decrease the adverse effect of global warming. Biomass is a widely accessible renewable energy source which reduces CO2 emissions for producing thermal energy or electricity. But the combustion of biomass is complex due its large variations and physical structures. Packed bed or fixed bed combustion is the most common method for the energy conversion of biomass. Experimental investigation of packed bed biomass combustion is difficult as the data collection inside the bed is challenging. CFD simulation of these combustion systems can be helpful to investigate different operational conditions and to evaluate the local values inside the investigation area. Available CFD codes can model the gas phase combustion but it can't model the solid phase of biomass conversion. In this work, a complete three-dimensional CFD model is presented for numerical investigation of packed bed biomass combustion. The model describes the solid phase along with the interface between solid and gas phase. It also includes the bed shrinkage due to the continuous movement of the bed during solid fuel combustion. Several variables are employed to represent different parameters of solid mass. Packed bed is considered as a porous bed and User Defined Functions (UDFs) platform is used to introduce solid phase user defined variables in the CFD. Modified standard discrete transfer radiation method (DTRM) is applied to model the radiation heat transfer. Preliminary results of gas phase velocity and pressure drop over packed bed have been shown. The model can be useful for investigation of movement of the packed bed during solid fuel combustion.

  4. A study of oxy-coal combustion with steam addition and biomass blending by thermogravimetric analysis

    OpenAIRE

    Gil Matellanes, María Victoria; Riaza Benito, Juan; Álvarez González, Lucía; Pevida García, Covadonga; Pis Martínez, José Juan; Rubiera González, Fernando

    2011-01-01

    The thermal characteristics of pulverized coal have been studied under oxy-fuel combustion conditions using non-isothermal thermogravimetric analysis (TG). The atmospheres used were 21%O2/79%N2, 21%O2/79%CO2, 30%O2/70%O2, and 35%O2/65%CO2. Coal blends of coal with 10 and 20% of biomass were also studied under these atmospheres. The addition of 10 and 20% of steam was evaluated for the oxy-fuel combustion atmospheres with 21 and 30% of O2 in order to study the effect of the wet recirculation o...

  5. Design, Optimization and Energetic Efficiency of Producing Hydrogen-Rich Gas from Biomass Steam Gasification

    Directory of Open Access Journals (Sweden)

    Po-Chih Kuo

    2014-12-01

    Full Text Available In this article, the conceptual design of biomass steam gasification (BSG processes using raw oil palm (ROP and torrefied oil palm (TOP are examined in an Aspen Plus simulator. Through thermodynamic analysis, it is verified that the BSG process with torrefied feedstock can effectively enhance the hydrogen yield. When the heat recovery design is added into the BSG process, the system energetic efficiency (SEE is significantly improved. Finally, an optimization algorithm with respect to SEE and hydrogen yield is solved, and the optimum operating conditions are validated by simulations.

  6. Continuous biological waste gas treatment in stirred trickle-bed reactor with discontinuous removal of biomass.

    Science.gov (United States)

    Laurenzis, A; Heits, H; Wübker, S; Heinze, U; Friedrich, C; Werner, U

    1998-02-20

    A new reactor for biological waste gas treatment was developed to eliminate continuous solvents from waste gases. A trickle-bed reactor was chosen with discontinuous movement of the packed bed and intermittent percolation. The reactor was operated with toluene as the solvent and an optimum average biomass concentration of between 5 and 30 kg dry cell weight per cubic meter packed bed (m3pb). This biomass concentration resulted in a high volumetric degradation rate. Reduction of surplus biomass by stirring and trickling caused a prolonged service life and prevented clogging of the trickle bed and a pressure drop increase. The pressure drop after biomass reduction was almost identical to the theoretical pressure drop as calculated for the irregular packed bed without biomass. The reduction in biomass and intermittent percolation of mineral medium resulted in high volumetric degradation rates of about 100 g of toluene m-3pb h-1 at a load of 150 g of toluene m-3pb h-1. Such a removal rate with a trickle-bed reactor was not reported before.

  7. Radioactive Demonstrations Of Fluidized Bed Steam Reforming (FBSR) With Hanford Low Activity Wastes

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M.; Crawford, C. L.; Burket, P. R.; Bannochie, C. J.; Daniel, W. G.; Nash, C. A.; Cozzi, A. D.; Herman, C. C.

    2012-10-22

    Several supplemental technologies for treating and immobilizing Hanford low activity waste (LAW) are being evaluated. One immobilization technology being considered is Fluidized Bed Steam Reforming (FBSR) which offers a low temperature (700-750?C) continuous method by which wastes high in organics, nitrates, sulfates/sulfides, or other aqueous components may be processed into a crystalline ceramic (mineral) waste form. The granular waste form produced by co-processing the waste with kaolin clay has been shown to be as durable as LAW glass. The FBSR granular product will be monolithed into a final waste form. The granular component is composed of insoluble sodium aluminosilicate (NAS) feldspathoid minerals such as sodalite. Production of the FBSR mineral product has been demonstrated both at the industrial, engineering, pilot, and laboratory scales on simulants. Radioactive testing at SRNL commenced in late 2010 to demonstrate the technology on radioactive LAW streams which is the focus of this study.

  8. Fluidized bed steam reformed mineral waste form performance testing to support Hanford Supplemental Low Activity Waste Immobilization Technology Selection

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Pierce, E. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Fox, K. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Herman, C. C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brown, C. F. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Qafoku, N. P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Neeway, J. J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Valenta, M. M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Gill, G. A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Swanberg, D. J. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Robbins, R. A. [Washington River Protection Solutions (WRPS), Richland, WA (United States); Thompson, L. E. [Washington River Protection Solutions (WRPS), Richland, WA (United States)

    2015-10-01

    This report describes the benchscale testing with simulant and radioactive Hanford Tank Blends, mineral product characterization and testing, and monolith testing and characterization. These projects were funded by DOE EM-31 Technology Development & Deployment (TDD) Program Technical Task Plan WP-5.2.1-2010-001 and are entitled “Fluidized Bed Steam Reformer Low-Level Waste Form Qualification”, Inter-Entity Work Order (IEWO) M0SRV00054 with Washington River Protection Solutions (WRPS) entitled “Fluidized Bed Steam Reforming Treatability Studies Using Savannah River Site (SRS) Low Activity Waste and Hanford Low Activity Waste Tank Samples”, and IEWO M0SRV00080, “Fluidized Bed Steam Reforming Waste Form Qualification Testing Using SRS Low Activity Waste and Hanford Low Activity Waste Tank Samples”. This was a multi-organizational program that included Savannah River National Laboratory (SRNL), THOR® Treatment Technologies (TTT), Pacific Northwest National Laboratory (PNNL), Oak Ridge National Laboratory (ORNL), Office of River Protection (ORP), and Washington River Protection Solutions (WRPS). The SRNL testing of the non-radioactive pilot-scale Fluidized Bed Steam Reformer (FBSR) products made by TTT, subsequent SRNL monolith formulation and testing and studies of these products, and SRNL Waste Treatment Plant Secondary Waste (WTP-SW) radioactive campaign were funded by DOE Advanced Remediation Technologies (ART) Phase 2 Project in connection with a Work-For-Others (WFO) between SRNL and TTT.

  9. Fluidized Bed Steam Reforming of Hanford LAW Using THORsm Mineralizing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Olson, Arlin L.; Nicholas R Soelberg; Douglas W. Marshall; Gary L. Anderson

    2004-11-01

    The U.S. Department of Energy (DOE) documented, in 2002, a plan for accelerating cleanup of the Hanford Site, located in southeastern Washington State, by at least 35 years. A key element of the plan was acceleration of the tank waste program and completion of ''tank waste treatment by 2028 by increasing the capacity of the planned Waste Treatment Plant (WTP) and using supplemental technologies for waste treatment and immobilization.'' The plan identified steam reforming technology as a candidate for supplemental treatment of as much as 70% of the low-activity waste (LAW). Mineralizing steam reforming technology, offered by THOR Treatment Technologies, LLC would produce a denitrated, granular mineral waste form using a high-temperature fluidized bed process. A pilot scale demonstration of the technology was completed in a 15-cm-diameter reactor vessel. The pilot scale facility was equipped with a highly efficient cyclone separator and heated sintered metal filters for particulate removal, a thermal oxidizer for reduced gas species and NOx destruction, and a packed activated carbon bed for residual volatile species capture. The pilot scale equipment is owned by the DOE, but located at the Science and Technology Applications Research (STAR) Center in Idaho Falls, ID. Pilot scale testing was performed August 2–5, 2004. Flowsheet chemistry and operational parameters were defined through a collaborative effort involving Idaho National Engineering and Environmental Laboratory, Savannah River National Laboratory (SRNL), and THOR Treatment Technologies personnel. Science Application International Corporation, owners of the STAR Center, personnel performed actual pilot scale operation. The pilot scale test achieved a total of 68.7 hrs of cumulative/continuous processing operation before termination in response to a bed de-fluidization condition. 178 kg of LAW surrogate were processed that resulted in 148 kg of solid product, a mass reduction of about 17%. The process

  10. Combustion and co-combustion of biomass in a bubbling fluidized bed boiler

    NARCIS (Netherlands)

    Khan, A.A.

    2007-01-01

    This PhD dissertation concerns the study of different aspects of biomass (co)-combustion in small-scale fluidized bed boilers for heat generation. The most renowned gaseous emissions from fluidized bed combustion, namely, CO and NO, are investigated with the help of experimental and theoretical stud

  11. Hydrogen production by steam reforming of higher hydrocarbons in a novel circulating fluidized bed reactor-regenerator system

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Z.; Elnashaie, S.; Yan, Y. [Auburn Univ., AL (United States). Dept. of Chemcial Engineering

    2003-07-01

    A mathematical model was developed to demonstrate the production of hydrogen by steam reforming of higher hydrocarbons in a circulating fluidized bed reactor-regenerator system (CFBRR). Heptane was the higher hydrocarbon used in this study. The process simulation of the riser steam reformer, catalyst regenerator, and downer indicate that the impact of catalyst deactivation is negligible because of the large mass flow ratio of solid to gas stream and the catalyst regenerator. The carbon deposited on the catalyst can be either gasified efficiently in the steam reformer or burned with air in the catalyst regenerator. The burning of carbon on the catalyst supplies the heat required for endothermic steam reforming of heptane and methane. This method has potential advantages for both energy consumption as well as hydrogen production.

  12. The influence of fine char particles burnout on bed agglomeration during the fluidized bed combustion of a biomass fuel

    Energy Technology Data Exchange (ETDEWEB)

    Scala, Fabrizio; Chirone, Riccardo [Istituto di Ricerche sulla Combustione, CNR, P.le V. Tecchio, 80-80125 Naples (Italy); Salatino, Piero [Dipartimento di Ingegneria Chimica, Universita degli Studi di Napoli Federico II, P.le V. Tecchio, 80-80125 Naples (Italy)

    2003-11-15

    The combustion of biomass char in a bubbling fluidized bed is hereby addressed, with specific reference to the influence that the combustion of fine char particles may exert on ash deposition and bed agglomeration phenomena. Experiments of steady fluidized bed combustion (FBC) of powdered biomass were carried out with the aim of mimicking the postcombustion of attrited char fines generated in the fluidized bed combustion of coarse char. Experimental results showed that the char elutriation rate is much smaller than expected on the basis of the average size of the biomass powder and of the carbon loading in the combustor. Samples of bed material collected after prolonged operation of the combustor were characterized by scanning electron microscopy (SEM)-EDX analysis and revealed the formation of relatively coarse sand-ash-carbon aggregates. The phenomenology is consistent with the establishment of a char phase attached to the bed material as a consequence of adhesion of char fines onto the sand particles. Combustion under sound-assisted fluidization conditions was also tested. As expected, enhancement of fines adhesion on bed material and further reduction of the elutriation rate were observed. Experimental results are interpreted in the light of a simple model which accounts for elutriation of free fines, adhesion of free fines onto bed material and detachment of attached fines by attrition of char-sand aggregates. Combustion of both free and attached char fines is considered. The parameters of the model are assessed on the basis of the measured carbon loadings and elutriation rates. Model computations are directed to estimate the effective size and the peak temperature of char-sand aggregates. The theoretical estimates of the effective aggregate size match fairly well those observed in the experiments.

  13. Fluidized Bed Steam Reforming of INEEL SBW Using THORsm Mineralizing Technology

    Energy Technology Data Exchange (ETDEWEB)

    Arlin L. Olson; Nicholas R. Soelberg; Douglas W. Marshall; Gary L. Anderson

    2004-12-01

    Sodium bearing waste (SBW) disposition is one of the U.S. Department of Energy (DOE) Idaho Operation Office’s (NE-ID) and State of Idaho’s top priorities at the Idaho National Engineering and Environmental Laboratory (INEEL). Many studies have resulted in the identification of five treatment alternatives that form a short list of perhaps the most appropriate technologies for the DOE to select from. The alternatives are (a) calcination with maximum achievable control technology (MACT) upgrade, (b) steam reforming, (c) cesium ion exchange (CsIX) with immobilization, (d) direct evaporation, and (e) vitrification. Each alternative has undergone some degree of applied technical development and preliminary process design over the past four years. DOE desired further experimental data, with regard to steam reforming technology, to make informed decisions concerning selection of treatment technology for SBW. Mineralizing steam reforming technology, offered by THOR Treatment Technologies, LLC would produce a denitrated, granular mineral waste form using a high-temperature fluidized bed process. A pilot scale demonstration of the technology was performed in a 15-cm-diameter reactor vessel September 27 through October 1, 2004. The pilot scale equipment is owned by the DOE, and located at the Science and Technology Applications Research (STAR) Center in Idaho Falls, ID. Flowsheet chemistry and operational parameters were defined through a collaborative effort involving Idaho National Engineering and Environmental Laboratory, Savannah River National Laboratory (SRNL), and THOR Treatment Technologies personnel. Personnel from Science Applications International Corporation, owners of the STAR Center, operated the pilot plant. The pilot scale test was terminated as planned after achieving a total of 100 hrs of cumulative/continuous processing operation. About 230 kg of SBW surrogate were processed that resulted in about 88 kg of solid product, a mass reduction of about 62

  14. Biomass Conversion into Solid Composite Fuel for Bed-Combustion

    Directory of Open Access Journals (Sweden)

    Tabakaev Roman B.

    2015-01-01

    Full Text Available The purpose of this research is the conversion of different types of biomass into solid composite fuel. The subject of research is the heat conversion of biomass into solid composite fuel. The research object is the biomass of the Tomsk region (Russia: peat, waste wood, lake sapropel. Physical experiment of biomass conversion is used as method of research. The new experimental unit for thermal conversion of biomass into carbon residue, fuel gas and pyrolysis condensate is described. As a result of research such parameters are obtained: thermotechnical biomass characteristics, material balances and product characteristics of the heat-technology conversion. Different methods of obtaining solid composite fuel from the products of thermal technologies are considered. As a result, it is established: heat-technology provides efficient conversion of the wood chips and peat; conversion of the lake sapropel is inefficient since the solid composite fuel has the high ash content and net calorific value.

  15. Steam reforming of biomass tar producing H2-rich gases over Ni/MgOx/CaO1-x catalyst.

    Science.gov (United States)

    Li, Chunshan; Hirabayashi, Daisuke; Suzuki, Kenzi

    2010-01-01

    Series nickel catalysts Ni/MgO(x)/CaO(1-)(x) (x=0.3, 0.5, 0.7, Ni: 5 wt%) were prepared and tested in fixed-bed reactor for biomass tar steam reforming, toluene as tar destruction model compound. Different ratios of MgO and CaO were mixed to simulate dolomite as Ni support. Two preparation methods: solid mixing with (SMW) and without water (SM) were used, the preparation methods and concentration of MgO had an important influence on toluene conversion and products. Catalysts prepared by SM method exhibited higher performance on toluene conversion, resulted in higher H(2) yield, and also, higher CO(2) and lower CO selectivity with higher temperature. For the same preparation method, higher concentration of MgO resulted in higher toluene conversion, and also influence on CO, CO(2) selectivity, but no obvious influence on the H(2) yield. Catalysts were characterized by BET, X-ray diffraction (XRD), SEM.

  16. Pyrolysis and gasification of biomass in a two-stage bluid bed gasification unit; Pyrolyse og forgasning af biomasse i en to-trins fluid bed forgasser

    Energy Technology Data Exchange (ETDEWEB)

    Hansen, M.W.; Henriksen, U. [Danmarks Tekniske Universitet (Denmark); Houmoeller, S. [dk-TEKNIK (Denmark)

    1997-07-01

    A new two-stage atmospheric bubbling fluid bed pyrolysis and gasification unit has been developed to convert straw and wood into a gas to be combusted in engines used for combined heat and power production. The unit combines the known two-stage process based on the fixed bed principle developed at the Department of Energy Engineering at the Technical University of Denmark, with the more compact and easy-to-scale fluid bed technique. The advantages of this combined concept is a relatively simple and easy to scale plant able to convert a wide range of fuels and producing a clean gas with extremely low tar content. Even straw can be converted which is of great importance in Denmark. The first stage, the pyrolysis unit, has been tested extensively as a means of pre-treating the biomass before co-combusting straw with fossil fuels in power plant boilers and it can eliminate the traditional corrosion problems on the boilers. The fluid bed pyrolysis unit converts the biomass into two fractions: A gas fraction to be combusted in the power plant boiler and a solids fraction, containing the major part of alkali and chlorine, to be converted otherwise. The gas fraction contains up to 75 percent of the energy of the input biomass. The idea is to avoid feeding the harmful components as potassium, sodium and chlorine present in the biomass into the boiler, as these components can cause corrosion damages to the super heater, but still supply the boiler with most of the biomass energy. This paper presents the concluded work on the co-combustion unit and the first results on the two-stage fluid bed pyrolysis and gasification unit. (EG)

  17. Biomass ash-bed material interactions leading to agglomeration in FBC

    DEFF Research Database (Denmark)

    Visser, H.J.M.; van Lith, Simone Cornelia; Kiel, J.H.A.

    2008-01-01

    In (bubbling) fluidized-bed combustion and gasification of biomass, several potential problems are associated with the inorganic components of the fuel. A major problem area is defluidization due to bed agglomeration. The most common found process leading to defluidization in commercial-scale ins......In (bubbling) fluidized-bed combustion and gasification of biomass, several potential problems are associated with the inorganic components of the fuel. A major problem area is defluidization due to bed agglomeration. The most common found process leading to defluidization in commercial...... describes a fundamental study on the mechanisms of defluidization. For the studied process of bed defluidization due to sintering of grain-coating layers, it was found that the onset of the process depends on (a) a critical coating thickness, (b) on the fluidization velocity when it is below approximately...... four times the minimum fluidization velocity, and (c) on the viscosity (stickiness) of the outside of the grains (coating)....

  18. Gasification of lignocellulosic biomass in fluidized beds for renewable energy development: A review

    Energy Technology Data Exchange (ETDEWEB)

    Alauddin, Zainal Alimuddin Bin Zainal; Lahijani, Pooya [School of Mechanical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Mohammadi, Maedeh; Mohamed, Abdul Rahman [School of Chemical Engineering, Engineering Campus, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

    2010-12-15

    A literature review on gasification of lignocellulosic biomass in various types of fluidized bed gasifiers is presented. The effect of several process parameters such as catalytic bed material, bed temperature and gasifying agent on the performance of the gasifier and quality of the producer gas is discussed. Based on the priorities of researchers, the optimum values of various desired outputs in the gasification process including improved producer gas composition, enhanced LHV, less tar and char content, high gas yield and enhanced carbon conversion and cold gas efficiency have been reported. The characteristics and performance of different fluidized bed gasifiers were assessed and the obtained results from the literature have been extensively reviewed. Survey of literature revealed that several industrial biomass gasification plants using fluidized beds are currently conducting in various countries. However, more research and development of technology should be devoted to this field to enhance the economical feasibility of this process for future exploitations. (author)

  19. Heat Transfer in a Fixed Biomass Char Bed

    DEFF Research Database (Denmark)

    Fjellerup, Jan Søren; Henriksen, Ulrik Birk; Glarborg, P.

    2002-01-01

    A thermal conductivity model based on the Yagi and Kunii model together with a bed model was developed to describe the thermal conductivity of a straw char bed. The bed model describes the relationship between the distance between particles and the external porosity. To verify the model, thermal...... conductivity experiments were performed on a wheat straw sample, which were cut in a shredder with two different sieves, 4 and 8 mm, and packed loosely in the thermal conductivity apparatus. The model, using external porosity and char diameter, compared reasonable well with experiments. The two straw samples...... and temperature on the thermal conductivity....

  20. Interpretation of biomass gasification yields regarding temperature intervals under nitrogen-steam atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Haykiri-Acma, H.; Yaman, S. [Istanbul Technical University, Chemical and Metallurgical Engineering Faculty, Chemical Engineering Department, 34469 Maslak, Istanbul (Turkey)

    2007-04-15

    Gasification of some agricultural waste biomass samples (sunflower shell, pine cone, cotton refuse, and olive refuse) and colza seed was performed using a thermogravimetric analyzer at temperatures up to 1273 K with a constant heating rate of 20 K/min under a dynamic nitrogen-steam atmosphere. Derivative thermogravimetric analysis profiles of the samples were derived from the non-isothermal thermogravimetric analysis data. Gasification yields of the biomass samples at temperature intervals of 473-553 K, 553-653 K, 653-773 K, 773-973 K, and 973-1173 K were investigated considering the successive stages of ''evolution of carbon oxides'', ''start of hydrocarbon evolution'', ''evolution of hydrocarbons'', ''dissociation'', and ''evolution of hydrogen'', respectively. Although, there were some interactions between these stages, some evident relations were observed between the gasification yields in a given stage and the chemical properties of the parent biomass materials. (author)

  1. Application of Fenton's reaction to steam explosion prehydrolysates from poplar biomass.

    Science.gov (United States)

    Oliva, J M; Manzanares, P; Ballesteros, I; Negro, M J; González, A; Ballesteros, M

    2005-01-01

    The application of Fenton's reaction to enhance the fermentability of prehydrolysates obtained from steam explosion pretreatment of poplar biomass was studied. Reaction conditions of temperature and H2O2 and Fe(II) concentrations were studied. The fermentability of prehydrolysate treated by Fenton's reaction was tested by using different inoculum sizes of thermotolerant strain Kluyveromyces marxianus CECT 10875. The highest percentages of toxic compound degradation (ranging from 71 to 93% removal) were obtained at the highest H2O2 concentration tested (50 mM). However, a negative effect on fermentability was observed at this H2O2 concentration at the lower inoculum loading. An increase in inoculum size to 0.6 g/L resulted in an enhanced ethanol fermentation yield of 95% relative to control.

  2. Simulation Studies of the Hydrogen Production from Methanol Partial Oxidation Steam Reforming by a Tubular Packed-bed Catalytic Reactor

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Hydrogen production by partial oxidation steam reforming of methanol over a Cu/ZnO/Al2 O3 cata lyst has been paid more and more attention. The chemical equilibria involved in the methanol partial oxidation steam reforming reaction network such as methanol partial oxidation, methanol steam reforming, decomposition of methanol and water-gas shift reaction have been examined over the ranges of temperature 473-1073 K under normal pressure. Based on the detailed kinetics of these reactions over a Cu/ZnO/Al2O3 catalyst, and from the basic concept of the effectiveness factor, the intraparticle diffusion limitations were taken into account. The effec tiveness factors for each reaction along the bed length were calculated. Then important results were offered for the simulation of this reaction process.

  3. Simulation Studies of the Hydrogen Production from Methanol Partial Oxidation Steam Reforming by a Tubular Packed-bed Catalytic Reactor*

    Institute of Scientific and Technical Information of China (English)

    蒋元力; 林美淑; 金东显

    2001-01-01

    Hydrogen production by partial oxidation steam reforming of methanol over a Cu/ZnO/Al2O3 cata-lyst has been paid more and more attention. The chemical equilibria involved in the methanol pvxtial oxidation steam reforming reaction network such as methanol partial oxidation, methanol steam reforming, decomposition of methanol and water-gas shift reaction have been examined over the ranges of temperature 473---1073 K under normal pressure. Based on the detailed kinetics of these reactions over a Cu/ZnO/Al2O3 catalyst, and from the basic concept of the effectiveness factor, the intraparticle diffusion limitations were taken into account. The effectiveness factors for each reaction along the bed length were calculated. Then important results were offered for the simulation of this reaction process.

  4. Characterization of hydrodynamics and solids mixing in fluidized beds involving biomass

    Science.gov (United States)

    Fotovat, Farzam

    This thesis focuses on the characterization of hydrodynamics and mixing phenomena in fluidized beds containing mixtures of sand and irregular biomass particles. The first objective of this study is understanding the effect of the large biomass particles on the bubbling characteristics and gas distribution pattern of sand fluidized beds. The second objective is the characterization of mixing/segregation of biomass and sand particles under fluidization conditions. A variety of experimental techniques are employed to study the behavior of two constituting phases of a fluidized bed, i.e., dilute (bubble) and dense (emulsion) phases. Exploring the characteristic fluidization velocities of sand-biomass mixtures unveils that the onset of bubbling in these systems occurs at a higher gas velocity compared to that of the initial fluidization velocity (Uif). The initial bubbling velocity (Uib), the final fluidization velocity ( Uff), and the transition gas velocity from bubbling to turbulent regime (Uc) rise by increasing the fraction of biomass in the mixture. Statistical analysis of the pressure signal at top of the bed reveals that increasing the biomass load hinders the evolution of bubbles at a low gas velocity (Ubeds containing different fractions of biomass is comparable. The addition of biomass particles to a bed of sand leads to an increase in the mean voidage of the bed; however, the voidage of each phase remains unaffected. It is observed that large biomass particles trigger a break-up of the bubbles, which results in boosting bubbling frequency. The fraction of bubbles at the center of the bed increases with the load of biomass. At the wall region, however, it starts to decrease by adding 2% wt. biomass to pure sand and then increases with the further addition of biomass. The Radioactive Particle Tracking (RPT) technique is implemented in the second section of this work to study the motion and distribution of biomass particles at U=0.36 m/s and U=0.64 m/s. In this

  5. FLASH PYROLYSIS OF BIOMASS PARTICLES IN FLUIDIZED BED FOR BIO-OIL PRODUCTION

    Institute of Scientific and Technical Information of China (English)

    Shurong Wang; Mengxiang Fang; Chunjiang Yu; Zhongyang Luo; Kefa Cen

    2005-01-01

    Biomass utilization could relieve the pressure caused by conventional energy shortage and environmental pollution. Advantage should be taken of the abundant biomass in China as clean energy source to substitute for traditional fossil fuels. At present, flash pyrolysis appears to be an efficient method to produce high yields of liquids that could either be directly used as fuel or converted to other valuable chemicals. Experiments were carried out of pyrolyzing biomass particles in a hot dense fluidized bed of sand to obtain high-quality bio-oil. Among four kinds of biomass species adopted in our experiment, Padauk Wood had the best characteristics in producing bio-oil. GC-MS analysis showed bio-oil to be a complex mixture consisting of many compounds. Furthermore, an integrated model was proposed to reveal how temperature influences biomass pyrolysis. Computation indicated that biomass particles underwent rapid heating before pyrolysis.

  6. Radionuclide and contaminant immobilization in the fluidized bed steam reforming waste products

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J.; Qafoku, Nikolla; Westsik, Joseph H.; Brown, Christopher F.; Jantzen, Carol; Pierce, Eric M.

    2012-05-01

    The goal of this chapter is to introduce the reader to the Fluidized Bed Steam Reforming (FBSR) process and resulting waste form. The first section of the chapter gives an overview of the potential need for FBSR processing in nuclear waste remediation followed by an overview of the engineering involved in the process itself. This is followed by a description of waste form production at a chemical level followed by a section describing different process streams that have undergone the FBSR process. The third section describes the resulting mineral product in terms of phases that are present and the ability of the waste form to encapsulate hazardous and radioactive wastes from several sources. Following this description is a presentation of the physical properties of the granular and monolith waste form product including and contaminant release mechanisms. The last section gives a brief summary of this chapter and includes a section on the strengths associated with this waste form and the needs for additional data and remaining questions yet to be answered. The reader is directed elsewhere for more information on other waste forms such as Cast Stone (Lockrem, 2005), Ceramicrete (Singh et al., 1997, Wagh et al., 1999) and geopolymers (Kyritsis et al., 2009; Russell et al., 2006).

  7. Performance of the Fluidized Bed Steam Reforming Product Under Hydraulically Unsaturated Conditions

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J.; Qafoku, Nikolla; Williams, Benjamin D.; Rod, Kenton A.; Bowden, Mark E.; Brown, Christopher F.; Pierce, Eric M.

    2014-05-01

    Currently, several candidates for secondary waste immobilization at the Hanford site in the State of Washington, USA are being considered. To demonstrate the durability of the product in the unsaturated Integrated Disposal Facility (IDF) at the site, a series of tests have been performed one of the candidate materials using the Pressurized Unsaturated Flow (PUF) system. The material that was tested was the Fluidized Bed Steam Reformer (FBSR) granular product and the granular product encapsulated in a geopolymer matrix. The FBSR product is composed primarily of an insoluble sodium aluminosilicate matrix with the dominant phases being feldspathoid minerals mostly nepheline, sodalite, and nosean. The PUF test method allows for the accelerated weathering of materials, including radioactive waste forms, under hydraulically unsaturated conditions, thus mimicking the open-flow and transport properties that most likely will be present at the IDF. The experiments show a trend of decreasing tracer release as a function of time for several of the elements released from the material including Na, Si, Al, and Cs. However, some of the elements, notably I and Re, show a steady release throughout the yearlong test. This result suggests that the release of these minerals from the sodalite cage occurs at a different rate compared with the dissolution of the predominant nepheline phase.

  8. A semi-empirical model for pressurised air-blown fluidized-bed gasification of biomass.

    Science.gov (United States)

    Hannula, Ilkka; Kurkela, Esa

    2010-06-01

    A process model for pressurised fluidized-bed gasification of biomass was developed using Aspen Plus simulation software. Eight main blocks were used to model the fluidized-bed gasifier, complemented with FORTRAN subroutines nested in the programme to simulate hydrocarbon and NH(3) formation as well as carbon conversion. The model was validated with experimental data derived from a PDU-scale test rig operated with various types of biomass. The model was shown to be suitable for simulating the gasification of pine sawdust, pine and eucalyptus chips as well as forest residues, but not for pine bark or wheat straw.

  9. Numerical Simulation of Biomass Gasification in a Fluidized Bed%流化床中生物质气化的数值模拟

    Institute of Scientific and Technical Information of China (English)

    李乾军; 潘效军; 张东平; 蒋斌

    2011-01-01

    基于欧拉多相流模型,自编化学反应子模型,通过建立生物质流化床气化动力学模型,对某实验室规模的流化床生物质气化炉进行了数值模拟,研究了蒸汽与生物质的质量比(mS/mB)、生物质粒径对产气组分、蒸汽分解率等的影响.结果表明:mS/mB增大,H2体积分数先上升后保持不变,而CO和CH4的体积分数先下降后几乎不变,蒸汽分解率下降;生物质粒径减小有利于气化过程,使CO和H2的体积分数明显上升;计算结果和试验结果基本吻合,表明基于欧拉多相流的动力学模型能对流化床中生物质的气化进行比较准确的模拟.%Based on Euler multiphase flow models and self-developed chemical reaction models,the dynamical model of biomass gasification in a fluidized bed was set up,with which numerical simulation was carried out to biomass gasification in a lab-scale biomass fluidized bed,so as to study the effect of mass ratio of steam and biomass(mS/mB) and biomass particle size on the gas composition and steam decomposition rate.Results show that with the rise of mS/mB,the volume fraction of H2 rises firstly and then remains unchanged,and that of CO and CH4 decreases firstly and then gets stable,while the steam decomposition rate drops gradually.The reduction of biomass particle size is in favor of the gasification process,which makes the volume fraction of CO and H2 rise.Simulation results basically agree with that of experiments,indicating that the dynamical model based on Euler multiphase flow can be used to simulate the biomass gasification in fluidized bed.

  10. Ashes from fluidized bed combustion of residual forest biomass

    NARCIS (Netherlands)

    Cruz, Nuno C.; Rodrigues, Sónia M.; Carvalho, Lina; Duarte, Armando C.; Pereira, Eduarda; Romkens, Paul; Tarelho, Luís A.C.

    2017-01-01

    Although bottom ash (BA) [or mixtures of bottom and fly ash (FA)] from clean biomass fuels is currently used as liming agent, additive for compost, and fertilizer on agricultural and forest soils in certain European countries, in several other countries most of the ashes are currently disposed in la

  11. An assessment of water and steam reactivation of a fluidized bed spent sorbent for enhanced SO{sub 2} capture

    Energy Technology Data Exchange (ETDEWEB)

    Montagnaro, F.; Salatino, P.; Scala, F.; Chirone, R. [University of Naples Federico 2, Naples (Italy)

    2008-01-15

    Hydration-induced reactivation of spent sorbents from fluidized bed combustion has long been proven as an attractive method to achieve better sorbent exploitation so as to positively affect waste disposal, consumption of natural resources and CO{sub 2} emission issues. The present study addresses the reactivation of the sulphur capture ability of fluidized bed (FB) spent sorbent particles by either water or steam hydration. Sorbent particles are subjected to different treatments including calcination, sulphation, hydration by either water or steam, dehydration and resulphation. Processing of sorbents is accomplished by the combined use of a bench scale (40 mm ID) fluidized bed reactor (calcination, sulphation, steam hydration, dehydration and resulphation) and of a thermostated water hydrator (water hydration). Reactivation of the limestone-based sorbent is characterized in terms of hydration degree and extent/pattern of particle sulphation with a further focus on the analysis of the reactivation-induced modifications of particle microstructural/chemical properties and propensity to undergo attrition and elutriation. The effectiveness of the two processes is analyzed, with consideration on the influence of process parameters on the ultimate degree of sorbent utilization. The feasibility of sorbent reactivation is discussed in the light of the effectiveness of sorbent reactivation and of the likely operational issues associated with either process.

  12. Prediction of product distribution in fine biomass pyrolysis in fluidized beds based on proximate analysis.

    Science.gov (United States)

    Kim, Sung Won

    2015-01-01

    A predictive model was satisfactorily developed to describe the general trends of product distribution in fluidized beds of lignocellulosic biomass pyrolysis. The model was made of mass balance based on proximate analysis and an empirical relationship with operating parameters including fluidization hydrodynamics. The empirical relationships between product yields and fluidization conditions in fluidized bed pyrolyzers were derived from the data of this study and literature. The gas and char yields showed strong functions of temperature and vapor residence time in the pyrolyzer. The yields showed a good correlation with fluidization variables related with hydrodynamics and bed mixing. The predicted product yields based on the model well accorded well with the experimental data.

  13. Granular bed filtration of high temperature biomass gasification gas.

    Science.gov (United States)

    Stanghelle, Daniel; Slungaard, Torbjørn; Sønju, Otto K

    2007-06-18

    High temperature cleaning of producer gas from biomass gasification has been investigated with a granular filter. Field tests were performed for several hours on a single filter element at about 550 degrees C. The results show cake filtration on the granular material and indicate good filtration of the biomass gasification producer gas. The relatively low pressure drop over the filter during filtration is comparable to those of bag filters. The granular filter can operate with high filtration velocities compared to bag filters and maintain high efficiency and a low residual pressure. This work is a part of the BioSOFC-up project that has a goal of utilizing the producer gas from the gasification plant in a solid oxide fuel cell (SOFC). The BioSOFC-up project will continue to the end of 2007.

  14. Application and research status of fluidized bed biomass gasification technologies%生物质流化床气化技术应用研究现状

    Institute of Scientific and Technical Information of China (English)

    孟凡彬; 刘建冲; 王贵路; 李晓伟; 张大雷

    2011-01-01

    According to the product s of biomass gasification, the purposes of biomass gasification could be classified into hydrogen production,power generation and synthetic liquid fuel This article introduced the features of hydrogen production from biomass steam gasification technology, catalytic gasification technology and supercritical water gasification technology, analyzed the technological and economic feasibility of fluidized bed biomass gasification and summarized the research status of fluidized bed biomass gasification to liquid fuel technology.It points out that the main bottleneck of biomass fluidized bed gasification technology is to change the stoichiometric ratio, to remove tar and to clean the produced synthesis gas It is surely that the oriented gasification will be the main tendency in the future.%按所得产品不同,可将生物质气化技术分为制氢、发电和合成液体燃料3大类.文章介绍了生物质流化床水蒸气气化制氢、催化气化制氢和超临界水气化制氢的工艺特点;分析了生物质流化床气化发电的技术、经济可行性;简述了生物质流化床气化合成液体燃料的研究现状;指出气化产出气化学当量比调变、焦油去除问题和合成气净化是生物质流化床气化技术应用的主要瓶颈,认为定向气化是今后研究的主要方向.

  15. Design and simulation of a circulating fluidized bed to clean the products of biomass gasification

    Energy Technology Data Exchange (ETDEWEB)

    Uchoa Neto, Moises; Carvalho, Yuri de Araujo [Dept. de Engenharia Mecanica. Faculdade de Tecnologia. Universidade de Brasilia, DF (Brazil); Oliveira, Taygoara Felamingo de; Barcelos, Manuel [Faculdade do Gama. Universidade de Brasilia, Gama, DF (Brazil)], e-mail: taygoara@unb.br

    2010-07-01

    The main goal of this work is to design a workbench circulating fluidized bed to study the cracking of tar in gases from the processes of biomass gasification. For this, a design methodology based on analytical results and empirical correlations for fluidized beds was employed. In parallel, a numerical code of open source technology (MFIX) for the solution of the transport equations of the multiphase flow in the column of a fluidized bed was used to give support to the choice of the design elements. The whole project of the workbench fluidized bed was completely developed, whose operation parameters such as bed geometry, gas velocity, circulating ratio and void fraction characterize a fast fluidization process. A preliminary mesh convergence study was executed with the numerical tool, that was validated comparing with analytical results. Among the most important results, the code computed the predicted value for the minimum fluidization. (author)

  16. Biomass Pyrolysis in a Fluidized Bed Reactor. Part 2: Experimental Validation of Model Results

    NARCIS (Netherlands)

    Wang, Xiaoquan; Kersten, Sascha R.A.; Prins, Wolter; Swaaij, van Wim P.M.

    2005-01-01

    Various types of cylindrical biomass particles (pine, beech, bamboo, demolition wood) have been pyrolyzed in a batch-wise operated fluid bed laboratory setup. Conversion times, product yields, and product compositions were measured as a function of the particle size (0.7−17 mm), the vapor's residenc

  17. Simulated Moving Bed Chromatography: Separation and Recovery of Sugars and Ionic Liquid from Biomass Hydrolysates

    Science.gov (United States)

    Caes, Benjamin R.; Van Oosbree, Thomas R.; Lu, Fachuang; Ralph, John; Maravelias, Christos T.

    2015-01-01

    Simulated moving bed chromatography, a continuous separation method, enables the nearly quantitative recovery of sugar products and ionic liquid solvent from chemical hydrolysates of biomass. The ensuing sugars support microbial growth, and the residual lignin from the process is intact. PMID:23939991

  18. FLUIDIZED BED STEAM REFORMING TECHNOLOGY FOR ORGANIC AND NITRATE SALT SUPERNATE

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Michael02 Smith, M

    2007-03-30

    About two decades ago a process was developed at the Savannah River Site (SRS) to remove Cs137 from radioactive high level waste (HLW) supernates so the supernates could be land disposed as low activity waste (LAW). Sodium tetraphenylborate (NaTPB) was used to precipitate Cs{sup 137} as CsTPB. The flowsheet called for destruction of the organic TPB by acid hydrolysis so that the Cs{sup 137} enriched residue could be mixed with other HLW sludge, vitrified, and disposed of in a federal geologic repository. The precipitation process was demonstrated full scale with actual HLW waste and a 2.5 wt% Cs137 rich precipitate containing organic TPB was produced admixed with 240,000 gallons of salt supernate. Organic destruction by acid hydrolysis proved to be problematic and other disposal technologies were investigated. Fluidized Bed Steam Reforming (FBSR), which destroys organics by pyrolysis, is the current baseline technology for destroying the TPB and the waste nitrates prior to vitrification. Bench scale tests were designed and conducted at the Savannah River National Laboratory (SRNL) to reproduce the pyrolysis reactions. The formation of alkali carbonate phases that are compatible with DWPF waste pre-processing and vitrification were demonstrated in the bench scale tests. Test parameters were optimized for a pilot scale FBSR demonstration that was performed at the SAIC Science & Technology Application Research (STAR) Center in Idaho Falls, ID by Idaho National Laboratory (INL) and SRNL in 2003. An engineering scale demonstration was completed by THOR{reg_sign} Treatment Technologies (TTT) and SRNL in 2006 at the Hazen Research, Inc. test facility in Golden, CO. The same mineral carbonate phases, the same organic destruction (>99.99%) and the same nitrate/nitrite destruction (>99.99%) were produced at the bench scale, pilot scale, and engineering scale although different sources of carbon were used during testing.

  19. Computational fluid dynamics modelling of biomass fast pyrolysis in fluidised bed reactors, focusing different kinetic schemes.

    Science.gov (United States)

    Ranganathan, Panneerselvam; Gu, Sai

    2016-08-01

    The present work concerns with CFD modelling of biomass fast pyrolysis in a fluidised bed reactor. Initially, a study was conducted to understand the hydrodynamics of the fluidised bed reactor by investigating the particle density and size, and gas velocity effect. With the basic understanding of hydrodynamics, the study was further extended to investigate the different kinetic schemes for biomass fast pyrolysis process. The Eulerian-Eulerian approach was used to model the complex multiphase flows in the reactor. The yield of the products from the simulation was compared with the experimental data. A good comparison was obtained between the literature results and CFD simulation. It is also found that CFD prediction with the advanced kinetic scheme is better when compared to other schemes. With the confidence obtained from the CFD models, a parametric study was carried out to study the effect of biomass particle type and size and temperature on the yield of the products.

  20. Modeling of NO and N{sub 2}O emissions from biomass circulating fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Liu, H.; Gibbs, B.M. [Leeds Univ., Leeds (United Kingdom). Dept. of Fuel and Energy

    2002-07-01

    In order to correctly model biomass combustion in a circulating fluidized bed (CFB) combustor, it is necessary to examine the four main stages in the combustion of biomass particles. These include drying, devolatilization, volatile combustion and char combustion in a CFB combustor. This paper presents a newly developed model for nitric oxide (NO) and nitrous oxide (N{sub 2}O) emissions from biomass-fired CFB combustors. A typical woody biomass of pinewood chips was selected for the model parameters. The drying and devolatilization of biomass particles was modeled with limited rates according to woody biomass fuels. The partition of fuel nitrogen between volatiles and char was chosen for pinewood based on available data from literature. It was assumed that the volatile nitrogen was composed of ammonia (NH{sub 3}), hydrogen cyanide (HCN) and nitrogen (N{sub 2}). The model included 25 chemical reactions, of which 20 belonged to global fuel-nitrogen reaction kinetics. A 12 MW CFB boiler was used to apply the model. Results were compared with experimental values as well as data from literature. The reaction between NO and char was found to be the key reaction that determines NO emissions. The catalytic effect of bed materials on the oxidation of NH{sub 3} and the the homogeneous reaction of NH{sub 3} with nitric oxide was also significant. 25 refs., 2 tabs., 5 figs.

  1. Hydrogen from biomass gas steam reforming for low temperature fuel cell: energy and exergy analysis

    Directory of Open Access Journals (Sweden)

    A. Sordi

    2009-03-01

    Full Text Available This work presents a method to analyze hydrogen production by biomass gasification, as well as electric power generation in small scale fuel cells. The proposed methodology is the thermodynamic modeling of a reaction system for the conversion of methane and carbon monoxide (steam reforming, as well as the energy balance of gaseous flow purification in PSA (Pressure Swing Adsorption is used with eight types of gasification gases in this study. The electric power is generated by electrochemical hydrogen conversion in fuel cell type PEMFC (Proton Exchange Membrane Fuel Cell. Energy and exergy analyses are applied to evaluate the performance of the system model. The simulation demonstrates that hydrogen production varies with the operation temperature of the reforming reactor and with the composition of the gas mixture. The maximum H2 mole fraction (0.6-0.64 mol.mol-1 and exergetic efficiency of 91- 92.5% for the reforming reactor are achieved when gas mixtures of higher quality such as: GGAS2, GGAS4 and GGAS5 are used. The use of those gas mixtures for electric power generation results in lower irreversibility and higher exergetic efficiency of 30-30.5%.

  2. Optimization of a Bubbling Fluidized Bed Plant for Low-Temperature Gasification of Biomass

    Directory of Open Access Journals (Sweden)

    María Pilar González-Vázquez

    2017-03-01

    Full Text Available Investigation into clean energies has been focused on finding an alternative to fossil fuels in order to reduce global warming while at the same time satisfying the world’s energy needs. Biomass gasification is seen as a promising thermochemical conversion technology as it allows useful gaseous products to be obtained from low-energy-density solid fuels. Air–steam mixtures are the most commonly used gasification agents. The gasification performances of several biomass samples and their mixtures were compared. One softwood (pine and one hardwood (chestnut, their torrefied counterparts, and other Spanish-based biomass wastes such as almond shell, olive stone, grape and olive pomaces or cocoa shell were tested, and their behaviors at several different stoichiometric ratios (SR and steam/air ratios (S/A were compared. The optimum SR was found to be in the 0.2–0.3 range for S/A = 75/25. At these conditions a syngas stream with 35% of H2 + CO and a gas yield of 2 L gas/g fuel were obtained, which represents a cold-gas efficiency of almost 50%. The torrefaction process does not significantly affect the quality of the product syngas. Some of the obtained chars were analyzed to assess their use as precursors for catalysts, combustion fuel or for agricultural purposes such as soil amendment.

  3. Preparation and initial characterization of fluidized bed steam reforming pure-phase standards

    Energy Technology Data Exchange (ETDEWEB)

    Missimer, D. M.; Rutherford, R. L.

    2013-03-21

    Hanford is investigating the Fluidized Bed Steam Reforming (FBSR) process for their Low Activity Waste. The FBSR process offers a low-temperature continuous method by which liquid waste can be processed with the addition of clay into a sodium aluminosilicate (NAS) waste form. The NAS waste form is mainly comprised of nepheline (NaAlSiO{sub 4}), sodalite (Na{sub 8}[AlSiO{sub 4}]{sub 6}Cl{sub 2}), and nosean (Na{sub 8}[AlSiO{sub 4}]{sub 6}SO{sub 4}). Anions such as perrhenate (ReO{sub 4}{sup -}), pertechnetate (TcO{sub 4}{sup -}), and iodine (I{sup -}) are expected to replace sulfate in the nosean structure and/or chloride in the sodalite mineral structure (atomically bonded inside the aluminosilicate cages that these mineral structures possess). In the FBSR waste form, each of these phases can exist in a variety of solid solutions that differ from the idealized forms observed in single crystals in nature. The lack of understanding of the durability of these stoichiometric or idealized mineral phases complicates the ability to deconvolute the durability of the mixed phase FBSR product since it is a combination of different NAS phases. To better understand the behavior, fabrication and testing of the individual phases of the FBSR product is required. Analytical Development (AD) of the Science and Technology directorate of the Savannah River National Laboratory (SRNL) was requested to prepare the series of phase-pure standards, consisting of nepheline, nosean, and Cl, Re, and I sodalite. Once prepared, X-ray Diffraction (XRD) analyses were used to confirm the products were phase pure. These standards are being used for subsequent characterization studies consisting of the following: single-pass flow-through (SPFT) testing, development of thermodynamic data, and x-ray diffraction (XRD) calibration curves. In addition to the above mentioned phase-pure standards, AD was tasked with fabricating a mixed Tc-Re sodalite.

  4. Performance of the Fluidized Bed Steam Reforming product under hydraulically unsaturated conditions

    Energy Technology Data Exchange (ETDEWEB)

    Neeway, James J [ORNL; Rod, Kenton A. [Pacific Northwest National Laboratory (PNNL); Bowden, Mark E [Pacific Northwest National Laboratory (PNNL); Pierce, Eric M [ORNL; Qafoku, Nikolla [Pacific Northwest National Laboratory (PNNL); Williams, Benjamin D [Pacific Northwest National Laboratory (PNNL); Brown, Christopher F [Pacific Northwest National Laboratory (PNNL)

    2014-01-01

    Several candidates for supplemental low-activity waste (LAW) immobilization at the Hanford site in Washington State, USA are being considered. One waste sequestering technology considered is Fluidized Bed Steam Reforming (FBSR). The granular product resulting from the FBSR process is composed primarily of an insoluble sodium aluminosilicate matrix with the dominant phases being feldspathoid minerals with a 1:1:1 molar ratio of Na, Al and Si. To demonstrate the durability of the product, which can be disposed of at the unsaturated Integrated Disposal Facility (IDF) at Hanford, a series of tests has been performed using the Pressurized Unsaturated Flow (PUF) system, which allows for the accelerated weathering of the solid materials. The system maintains hydraulically unsaturated conditions, thus mimicking the open-flow and transport properties that will be present at the IDF. Two materials were tested using the system: 1) the FBSR granular product and 2) the FBSR granular product encapsulated in a geopolymer to form a monolith. Results of the experiments show a trend of relatively constant effluent concentration of Na, Si, Al, and Cs as a function of time from both materials. The elements I and Re show a steady release throughout the yearlong test from the granular material but their concentrations seem to be increasing at one year from the monolith material. This result suggests that these two elements may be present in the sodalite cage structure rather than in the predominant nepheline phase because their release occurs at a different rate compared to nepheline phase. Also, these elements to not seem to reprecipitate when released from the starting material. Calculated one-year release rates for Si are on the order of 10 6 g/(m2 d) for the granular material and 10 5 g/(m2 d) for the monolith material while Re release is seen to be two orders of magnitude higher than Si release rates. SEM imaging and XRD analysis show how the alteration of the two materials is

  5. Considerations on valorization of biomass origin materials in co-combustion with coal in fluidized beds

    Energy Technology Data Exchange (ETDEWEB)

    I. Gulyurtlu; P. Abelha; H. Lopes; A. Crujeira; I. Cabrita [DEECA-INETI, Lisbon (Portugal)

    2007-07-01

    Co-combustion of biomass materials with coal is currently gaining increasing importance, in order to meet the targets on greenhouse gas emissions, defined in the Kyoto protocol. Co-firing of coal with biomass materials could be the short-term solution in reducing CO{sub 2} emissions from power stations. The work undertaken studied co-firing of meat and bone meal (MBM), olive cake and straw pellets with bituminous coals from Colombia (CC) and Poland (PC), which are commonly used in European power stations. The co-combustion studies were carried out on the pilot fluidized bed installation of INETI. Gaseous pollutants and solid concentration in flue gases and ashes from different locations were monitored. Results obtained indicate that the co-feeding of biomass materials did not present any problem and ensured stable combustion conditions and high efficiency. However, for temperatures above 800{sup o}C, bed agglomeration could be observed for all biomass species studied. Most of the combustion of biomass material, contrary to that of coal, was observed to take place in the riser where the temperature was as high as 150-250{sup o}C above that of the bed. SO{sub 2} and NOx levels were found to be lower. The emissions of dioxins could be considerable with fuels with high Cl as is the case with straw. However, mixing of fuels with high S content could lead to a strong reduction in dioxin emissions. Ashes produced from biomass combustion may be considered for further reutilization or landfilling. Other options depend on their characteristics, chemical composition and leaching behaviour. This was evaluated in this study.

  6. Steam explosion distinctively enhances biomass enzymatic saccharification of cotton stalks by largely reducing cellulose polymerization degree in G. barbadense and G. hirsutum.

    Science.gov (United States)

    Huang, Yu; Wei, Xiaoyang; Zhou, Shiguang; Liu, Mingyong; Tu, Yuanyuan; Li, Ao; Chen, Peng; Wang, Yanting; Zhang, Xuewen; Tai, Hongzhong; Peng, Liangcai; Xia, Tao

    2015-04-01

    In this study, steam explosion pretreatment was performed in cotton stalks, leading to 5-6 folds enhancements on biomass enzymatic saccharification distinctive in Gossypium barbadense and Gossypium hirsutum species. Sequential 1% H2SO4 pretreatment could further increase biomass digestibility of the steam-exploded stalks, and also cause the highest sugar-ethanol conversion rates probably by releasing less inhibitor to yeast fermentation. By comparison, extremely high concentration alkali (16% NaOH) pretreatment with raw stalks resulted in the highest hexoses yields, but it had the lowest sugar-ethanol conversion rates. Characterization of wall polymer features indicated that biomass saccharification was enhanced with steam explosion by largely reducing cellulose DP and extracting hemicelluloses. It also showed that cellulose crystallinity and arabinose substitution degree of xylans were the major factors on biomass digestibility in cotton stalks. Hence, this study has provided the insights into cell wall modification and biomass process technology in cotton stalks and beyond.

  7. Fixed bed pyrolysis of biomass solid waste for bio-oil

    Science.gov (United States)

    Islam, Mohammad Nurul; Ali, Mohamed Hairol Md; Haziq, Miftah

    2017-08-01

    Biomass solid waste in the form of rice husk particle is pyrolyzed in a fixed bed stainless steel pyrolysis reactor of 50 mm diameter and 50 cm length. The biomass solid feedstock is prepared prior to pyrolysis. The reactor bed is heated by means of a cylindrical heater of biomass source. A temperature of 500°C is maintained with an apperent vapor residence time of 3-5 sec. The products obtained are liquid bio-oil, solid char and gases. The liquid product yield is found to be 30% by weight of solid biomass feedstock while the solid product yield is found to be 35% by weight of solid biomass feedtock, the rest is gas. The bio-oil is a single-phase brownish color liquid of acrid smell. The heating value of the oil is determined to be 25 MJ/kg. The density and pH value are found to be 1.125 kg/m3 and 3.78 respectively.

  8. A high temperature drop-tube and packed-bed solar reactor for continuous biomass gasification

    Science.gov (United States)

    Bellouard, Quentin; Abanades, Stéphane; Rodat, Sylvain; Dupassieux, Nathalie

    2017-06-01

    Biomass gasification is an attractive process to produce high-value syngas. Utilization of concentrated solar energy as the heat source for driving reactions increases the energy conversion efficiency, saves biomass resource, and eliminates the needs for gas cleaning and separation. A high-temperature tubular solar reactor combining drop tube and packed bed concepts was used for continuous solar-driven gasification of biomass. This 1 kW reactor was experimentally tested with biomass feeding under real solar irradiation conditions at the focus of a 2 m-diameter parabolic solar concentrator. Experiments were conducted at temperatures ranging from 1000°C to 1400°C using wood composed of a mix of pine and spruce (bark included) as biomass feedstock. The aim of this study was to demonstrate the feasibility of syngas production in this reactor concept and to prove the reliability of continuous biomass gasification processing using solar energy. The study first consisted of a parametric study of the gasification conditions to obtain an optimal gas yield. The influence of temperature and oxidizing agent (H2O or CO2) on the product gas composition was investigated. The study then focused on solar gasification during continuous biomass particle injection for demonstrating the feasibility of a continuous process. Regarding the energy conversion efficiency of the lab scale reactor, energy upgrade factor of 1.21 and solar-to-fuel thermochemical efficiency up to 28% were achieved using wood heated up to 1400°C.

  9. Hydrodynamic study on gasification of biomass in a fluidized bed gasifier

    Directory of Open Access Journals (Sweden)

    S.BASKARA SETHUPATHY

    2012-01-01

    Full Text Available Current scenario of energy insecurity urges us to realize the importance of alternate energy sources. In country with variety of vegetation like India, Biomass finds its place of which fluidized bed gasification of biomass could be more effective. This paper emphasizes the importance of a fluidized bed gasifier for energy conversion of agro-residues for useful purposes. Coconut Shell and Ground nut shell of gross calorific value 19.43MJ/kg and 14.91 MJ/kg respectively are taken for the study. The particle size is restricted not to exceed 3mm. Various empirical correlations involved in fluidization are studied and their interdependence is detailed. From various published data, importance of inert materials and their relative proportions with biomass fuels are studied and optimum biomass to sand ratio is fixed as 10 to 15% by mass. Equations for predicting the minimum fluidization velocities of these mixtures are also discussed. Variations of Fluidization parameters such asminimum fluidization velocity, bubble rise velocity, expanded bed height with respect to temperature, equivalence ratio, particle size is studied and their quantification is analyzed. A 108 mm internal diameter and 1400 mm high FBG is used for the study. Fuel is fed through screw feeder and air is supplied through blower. In the down stream side cyclone separator is placed after which the sampling and burner lines are connected. A regression model is developed and the feasibility of gasifying coconut shell and groundnut shell are discussed. Earlier and present work of coconut shell gasification proves fluidized bed gasification is more appropriate for agro residues.

  10. On a clean power generation system with the co-gasification of biomass and coal in a quadruple fluidized bed gasifier.

    Science.gov (United States)

    Yan, Linbo; He, Boshu

    2017-07-01

    A clean power generation system was built based on the steam co-gasification of biomass and coal in a quadruple fluidized bed gasifier. The chemical looping with oxygen uncoupling technology was used to supply oxygen for the calciner. The solid oxide fuel cell and the steam turbine were combined to generate power. The calcium looping and mineral carbonation were used for CO2 capture and sequestration. The aim of this work was to study the characteristics of this system. The effects of key operation parameters on the system total energy efficiency (ŋten), total exergy efficiency (ŋtex) and carbon sequestration rate (Rcs) were detected. The energy and exergy balance calculations were implemented and the corresponding Sankey and Grassmann diagrams were drawn. It was found that the maximum energy and exergy losses occurred in the steam turbine. The system ŋten and ŋtex could be ∼50% and ∼47%, and Rcs could be over unit. Copyright © 2017 Elsevier Ltd. All rights reserved.

  11. Fluidized bed gasification of biomass, waste, and coal, for different applications

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E. [VTT Energy, Espoo (Finland). Gasification and Gas Cleaning Group

    1998-12-31

    Various energy production systems based on biomass and waste gasification are being developed in Finland by VTT and its industrial partners. In 1986 - 1995, the Finnish gasification R and D activities were almost fully devoted to the development of simplified IGCC power systems suitable to large-scale power production based on pressurised fluid bed gasification, hot gas cleaning, and a combined-cycle process. Within the LIEKKI 2 programme, VTT continued this R and D by carrying out cogasification tests with coal and biomass fuels and by studying the formation of gas contaminants in fluidized bed gasification. In the mid-1990`s, the atmospheric pressure gasification activities aiming at small- and medium-size power plants based on gas/diesel engines were restarted in Finland. Since 1995, intensive R and D is also focused on atmospheric pressure circulating fluidized bed gasification of biomass residues and wastes. This gasification technology earlier commercialised for lime kiln applications is now aiming to co-utilise locally-available residues and wastes in existing pulverised-coal-fired boilers. The research at VTT in this field is related to the gasification of biofuels with problematic ash behaviour and to gas cleaning from alkali/heavy metals and chlorine. The experimental gasification R and D was complemented by techno-economic and market studies focusing on the potentials of different process alternatives. (orig.) 12 refs.

  12. SO2 -catalyzed steam explosion: the effects of different severity on digestibility, accessibility, and crystallinity of lignocellulosic biomass.

    Science.gov (United States)

    Kang, Yuzhi; Bansal, Prabuddha; Realff, Matthew J; Bommarius, Andreas S

    2013-01-01

    Lignocellulosic biomass is the most promising feedstock for biofuels production. To enhance the efficiency of enzymatic hydrolysis, lignocellulosics needs to be pretreated to lower their recalcitrance. SO(2) -catalyzed steam explosion is an efficient and relatively cost-efficient pretreatment method for softwood. This work investigates the effects of steam explosion severity on the digestibility, accessibility, and crystallinity of Loblolly pine. Higher severity was found to increase the accessibility of the feedstock while also promoting nonselective degradation of carbohydrates. The adsorption behavior of Celluclast® enzymes on steam-exploded Loblolly pine (SELP) can be described by a Langmuir isotherm. Cellulose crystallinity was found to first increase and then decrease with increasing pretreatment severity. A linear relationship between initial hydrolysis rates and crystallinity index (CrI) of pretreated Loblolly pine was found; moreover, a strong correlation between X-ray diffraction intensities and initial rates was confirmed. The findings demonstrate the significance of CrI in enzymatic hydrolysis of pretreated lignocellulosic biomass.

  13. Modelling and simulation of a circulating fluidized-bed steam generator as an aid for process analysis and automation. Modellierung und Simulation eines ZWS-Dampferzeugers als Hilfsmittel zur Prozessanalyse und -automatisierung

    Energy Technology Data Exchange (ETDEWEB)

    Karbach, A.; Peters, R.; Schaub, G. (Lurgi GmbH, Frankfurt am Main (Germany, F.R.))

    1990-04-01

    This book deals with the development and application of mathematical model for the simulation of a steam generator with fluidized-bed combustion (coal combustion in the circulating fluidized-bed combustion). (orig./EF).

  14. A CFD model for biomass fast pyrolysis in fluidized-bed reactors

    Science.gov (United States)

    Xue, Qingluan; Heindel, T. J.; Fox, R. O.

    2010-11-01

    A numerical study is conducted to evaluate the performance and optimal operating conditions of fluidized-bed reactors for fast pyrolysis of biomass to bio-oil. A comprehensive CFD model, coupling a pyrolysis kinetic model with a detailed hydrodynamics model, is developed. A lumped kinetic model is applied to describe the pyrolysis of biomass particles. Variable particle porosity is used to account for the evolution of particle physical properties. The kinetic scheme includes primary decomposition and secondary cracking of tar. Biomass is composed of reference components: cellulose, hemicellulose, and lignin. Products are categorized into groups: gaseous, tar vapor, and solid char. The particle kinetic processes and their interaction with the reactive gas phase are modeled with a multi-fluid model derived from the kinetic theory of granular flow. The gas, sand and biomass constitute three continuum phases coupled by the interphase source terms. The model is applied to investigate the effect of operating conditions on the tar yield in a fluidized-bed reactor. The influence of various parameters on tar yield, including operating temperature and others are investigated. Predicted optimal conditions for tar yield and scale-up of the reactor are discussed.

  15. Attached biomass growth and substrate utilization rate in a moving bed biofilm reactor

    Directory of Open Access Journals (Sweden)

    J. J. Marques

    2008-12-01

    Full Text Available A moving bed bioreactor containing cubes of polyether foam immersed in a synthetic wastewater (an aqueous mixture of meat extract, yeast extract, dextrose, meat peptone, ammonium chloride, potassium chloride, sodium chloride, sodium bicarbonate, potassium mono-hydrogen-phosphate and magnesium sulphate was used to evaluate bacterial growth and biomass yield parameters based on Monod's equation. The wastewater was supplied in the bottom of the equipment flowing ascending in parallel with a diffused air current that provided the mixing of the reactor content. Suspended and attached biomass concentration was measured through gravimetric methods. Good agreement was found between experimental kinetic parameters values and those obtained by other researchers. The only significant difference was the high global biomass content about 2 times the values obtained in conventional processes, providing high performance with volumetric loading rates up to 5.5 kg COD/m³/d.

  16. Development of novel fixed-bed gasification for biomass residues and agrobiofuels

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Simell, P.; Staahlberg, P. [VTT Energy, Espoo (Finland). New Energy Technologies; Berna, G. [Finesport Engineering (Italy); Barbagli, F. [Antiche Terre (Italy); Haavisto, I. [Condens Oy (Finland)

    2000-11-01

    The project concerned three different approaches to achieve reliable operation in fixed-bed gasification of available biomass residues. The first approach was based on the pretreatment of fuels for use in standard downdraft gasifiers. The second one was based on using a commercially available updraft fixed-bed gasifier for heating applications. The third was based on the development of a new type of gasifier that were independent of the natural descending fuel flow caused by gravity. The downdraft gasification tests were carried out in Italy in a gasifier-engine-generator facility with a range of Italian biofuels, the aim being to create criteria for fuel selection, collect reliable performance data with suitable fuels and to identify technical possibilities for broadening the feedstock basis by using mixture fuels and additives. The test results and experiences clearly demonstrated the limitations of this type of commercial gasification technology. Operation experiences of commercial updraft gasifiers operating in Finland and Sweden were collected and evaluated. These updraft gasifiers operate well with sod peat and wood chips. However, these gasifiers cannot operate reliably with low-bulk density fibours fuels like bark, sawdust and shavings. The third technical approach was realised by designing, constructing and testing a pilot plant of a new type of gasifier, based on forced fuel flow and suitable for low-bulk-density fibrous biomass fuels. The pilot plant was connected to a secondary catalytic gas cleaning device, which made it possible to produce tar-free gas suitable for engine use. This new fixed-bed gasifier makes it possible to utilise such biomass residues and energy crops that cannot be used in the presently available fixed-bed gasifiers, like forest residue chips, sawdust and crushed bark. However, further work is required to demonstrate the whole gasifier, gas cleaning and engine concept and to define the lifetime and availability of the catalytic

  17. Biomass Torrefaction Process Review and Moving Bed Torrefaction System Model Development

    Energy Technology Data Exchange (ETDEWEB)

    Jaya Shakar Tumuluru; Shahab Sokhansanj; Christopher T. Wright; Richard D. Boardman

    2010-08-01

    Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300 C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-230 C and 270-280 C. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, producing a final product that will have a lower mass but a higher heating value. An important aspect of research is to establish a degree of torrefaction where gains in heating value offset the loss of mass. There is a lack of literature on torrefaction reactor designs and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes (a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and (b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed for different capacities, designing the heat loads and gas flow rates, and developing an interactive excel sheet where the user can define design specifications. In this report, 25-1000 kg/hr are used in equations for the design of the torrefier, examples of calculations, and specifications for the torrefier.

  18. Biomass Torrefaction Process Review and Moving Bed Torrefaction System Model Development

    Energy Technology Data Exchange (ETDEWEB)

    Jaya Shakar Tumuluru; Shahab Sokhansanj; Christopher T. Wright

    2010-08-01

    Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300°C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200–230ºC and 270–280ºC. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, producing a final product that will have a lower mass but a higher heating value. An important aspect of research is to establish a degree of torrefaction where gains in heating value offset the loss of mass. There is a lack of literature on torrefaction reactor designs and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed for different capacities, designing the heat loads and gas flow rates, and developing an interactive excel sheet where the user can define design specifications. In this report, 25–1000 kg/hr are used in equations for the design of the torrefier, examples of calculations, and specifications for the torrefier.

  19. Ethanol from lignocellulosic biomasses; Etanolo da biomasse lignocellulosiche. Produzione di etanolo da paglia di grano mediante pretrattamento di steam explosion, idrolisi enzimatica e fermentazione

    Energy Technology Data Exchange (ETDEWEB)

    Ricci, E.; Viola, E.; Zimbardi, F.; Braccio, G. [ENEA, Divisione Fonti Rinnovabili di Energia, Centro Ricerche Trisaia, Policoro, Matera (Italy); Cuna, D. [Faucitano Srl, Milan (Italy)

    2001-07-01

    In this report are presented results achieved on the process optimisation of bioethanol production from wheat straw, carried out within the ENEA's project of biomass exploitation for renewable energy. The process consists of three main steps: 1) biomass pretreatment by means of steam explosion; 2) enzymatic hydrolysis of the cellulose fraction; 3) fermentation of glucose. To perform the hydrolysis step, two commercial enzymatic mixtures have been employed, mainly composed by {beta}-glucosidase (cellobiase), endo-glucanase and exo-glucanase. The ethanologenic yeast Saccharomyces cerevisiae has been used to ferment the glucose in he hydrolyzates. Hydrolysis yield of 97% has been obtained with steam exploded wheat straw treated at 220{sup 0}C for 3 minutes and an enzyme to substrate ratio of 4%. It has been pointed out the necessity of washing with water the pretreated what straw, in order to remove the biomass degradation products, which have shown an inhibition effect on the yeast. At the best process conditions, a fermentation yield of 95% has been achieved. In the Simultaneous Saccharification and Fermentation process, a global conversion of 92% has been obtained, which corresponds to the production of about 170 grams of ethanol per kilogram of exploded straw. [Italian] Si riportano i risultati di un'attivita' di ricerca finalizzata all'ottimizzazione del processo di produzione di etanolo da paglia di grano. Il processo esaminato consta di un pretrattamento mediante steam explosion della paglia, seguito da idrolisi enzimatica della cellulosa e fermentazione del glucosio ottenuto. Per effettuare l'idrolisi sono stati utilizzati due preparati enzimatici disponibili commercialmente, costituiti da {beta}-glucosidasi, endo-glucanasi ed eso-glucanasi. Per la fermentazione del glucosio negli idrolizzati e' stato impiegato il lievito Saccharomyces cerevisae. E' stata raggiunta un'efficienza massima di idrolisi del 97% utilizzando

  20. Research on the Gas Reburning in a Circulating Fluidized Bed (CFB System Integrated with Biomass Gasification

    Directory of Open Access Journals (Sweden)

    Changqing Dong

    2012-08-01

    Full Text Available N2O emissions from coal fired fluidized-bed combustion are approximately 30–360 mg/Nm3, much higher than that from pulverized coal combustion (less than 30 mg/Nm3. One approach to reduce the N2O is to reburn the biomass gasification gas in the coal-fired fluidized bed. In this paper, the effects of gasified biomass reburning on the integrated boiler system were investigated by both simulation and experimental methods. The simulation as well as experimental results revealed that the increase of the reburning ratio would decrease the theoretical air volume and boiler efficiency, while it would increase the fuel gas volume, combustion and exhuast gas temperature. The experimental results also indicated that the N2O removal could reach as high as 99% when the heat ratio of biomass gas to coal is 10.5%.

  1. Effects of biomass on dynamics of combustion in circulating fluidized beds

    Directory of Open Access Journals (Sweden)

    Tourunen Antti

    2004-01-01

    Full Text Available Fluidized bed technology is very suitable for the combustion of biomass Nevertheless substitution of coal with biomass affects boiler operation and especially dynamics and controllability. Non-homogeneity of biomass and fuel feeding disturbances cause process instability, such as variations in temperatures and pressures, which reduce lifetime of equipment and structures. Because of process instability higher air coefficient must be used in order to avoid CO emissions, which is not economical. Combustion profiles for coal, wood and peat, measured at the VTT Processes Pilot circulating fluidized bed reactor, have been compared. Process stability and char inventories have been studied by the measurements and the model. Biofuel are usually very reactive and their combustion profiles are quite different compared to coals. Because of high reactivity and low char content combustion process with biofuel is very sensitive for fuel feeding. Also low char inventory effect on load changes combined with combustion profile that differs from coals. Because of different combustion profile heat transfer can be a limiting factor in load changes despite the high reactivity and fast oxygen response.

  2. Simulation of emission performance and combustion efficiency in biomass fired circulating fluidized bed combustors

    Energy Technology Data Exchange (ETDEWEB)

    Gungor, Afsin [Nigde University, Faculty of Engineering and Architecture, Department of Mechanical Engineering, 51100 Nigde (Turkey)

    2010-04-15

    In this study, the combustion efficiency and the emission performance of biomass fired CFBs are tested via a previously published 2D model [Gungor A. Two-dimensional biomass combustion modeling of CFB. Fuel 2008; 87: 1453-1468.] against two published comprehensive data sets. The model efficiently simulates the outcome with respect to the excess air values, which is the main parameter that is verified. The combustion efficiency of OC changes between 82.25 and 98.66% as the excess air increases from 10 to 116% with the maximum error of about 8.59%. The rice husk combustion efficiency changes between 98.05 and 97.56% as the bed operational velocity increases from 1.2 to 1.5 m s{sup -1} with the maximum error of about 7.60%. CO and NO{sub x} emissions increase with increasing bed operational velocity. Increasing excess air results in slightly higher levels of NO{sub x} emission. A significant amount of combustion occurs in the upper zone due to the high volatile content of the biomass fuels. (author)

  3. Characterization of Combustion and Emission of Several Kinds of Herbaceous Biomass Pellets in a Circulating Fluidized Bed Combustor

    Science.gov (United States)

    Li, S. Y.; Teng, H. P.; Jiao, W. H.; Shang, L. L.; Lu, Q. G.

    Characterizations of combustion and emission of four kinds of herbaceous biomass pellets were investigated in a 0.15 MWt circulating fluidized bed. Corn stalk, wheat stalk, cotton stalk and king grass, which are typical herbaceous biomass in China, were chosen for this study. Temperature profile, emission in flue gas and agglomeration were studied by changing the combustion temperature between 750°C and 880°C. The combustion efficiencies are in the range from 97.4% to 99.4%, which are relatively high due to the homogeneous temperature profiles and good circulating fluidization of bed material. Suitable combustion temperatures for the different herbaceous biomass are mainly depended on the emission and bed agglomeration. SO2 and HCl concentrations in flue gas are in direct proportion to the sulfur and chlorine contents of the herbaceous biomass. Agglomeration at the cyclone leg and the loop seal is the main reason for defluidization in the CFB combustor.

  4. Changes in char reactivity due to char-oxygen and char-steam reactions using Victorian brown coal in a fixed-bed reactor

    Institute of Scientific and Technical Information of China (English)

    Shu Zhang; Yonggang Luo; Chunzhu Li; Yonggang Wang

    2015-01-01

    This study was to examine the influence of reactions of char–O2 and char–steam on the char reactivity evolution. A newly-designed fixed-bed reactor was used to conduct gasification experiments using Victorian brown coal at 800 °C. The chars prepared from the gasification experiments were then collected and subjected to reactivity characterisation (ex-situ reactivity) using TGA (thermogravimetric analyser) in air. The results indicate that the char reactivity from TGA was generally high when the char experienced intensive gasification reactions in 0.3%O2 in the fixed-bed reactor. The addition of steam into the gasification not only enhanced the char conversion sig-nificantly but also reduced the char reactivity dramatical y. The curve shapes of the char reactivity with involve-ment of steam were very different from that with O2 gasification, implying the importance of gasifying agents to char properties.

  5. Biomass Fuel and Combustion Conditions Selection in a Fixed Bed Combustor

    Directory of Open Access Journals (Sweden)

    María E. Arce

    2013-11-01

    Full Text Available The biomass market has experienced an increase in development, leading to research and development efforts that are focused on determining optimal biofuel combustion conditions. Biomass combustion is a complex process that involves divergent parameters and thus requires the use of advanced analysis methods. This study proposes combining grey relational analysis (GRA and error propagation theory (EPT to select a biofuel and its optimal combustion conditions. This research will study three biofuels that are currently used in a region of South Europe (Spain, and the most important variables that affect combustion are the ignition front propagation speed and the highest temperature that is reached at the fixed bed combustor. The results demonstrate that a combination of both theories for the analysis of solid-state thermochemical phenomena enables a fast and simple way of choosing the best configuration for each fuel.

  6. Ash behavior and de-fluidization in low temperature circulating fluidized bed biomass gasifier

    DEFF Research Database (Denmark)

    Narayan, Vikas

    . It was observed that of the total fuel ash entering the system, a large fraction (40-50%) of the ash was retained in the secondary cyclone bottoms and a lower amount (8-10%) was released as dust in the exit gas; the residual ash was accumulated within the fluidized bed system. A dominant fraction of alkali...... by the ash particle size and the cut size of the primary and secondary cyclones. A model accounting for the ash collection by the plant cyclones was developed which predicted the product gas ash particle release reasonably well. The present work also aims to understand the effect of biomass fuel ash...

  7. Gasification of biomass and coal in a pressurised fluidised bed gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Andries, J.; Jong, W. de; Hein, K.R.G. [Technische Univ. Delft (Netherlands)

    1998-09-01

    During a 3 year (1996-1998) multinational JOULE project, partly funded by the EU, experimental and theoretical research is being done on co-gasification of biomass (pelletised straw and Miscanthus) and coal in a pressurised fluidised bed reactor. The influence of feedstock and operating conditions on gasification characteristics has been studied using a 1.5 MW{sub th} gasifier, which has been operated at a pressure of 5 bar and temperatures up to 900 C. The project and the test rig are described and results obtained in the first part of the project are presented and analysed. (orig.)

  8. Steam-exploded biomass saccharification is predominately affected by lignocellulose porosity and largely enhanced by Tween-80 in Miscanthus.

    Science.gov (United States)

    Sun, Dan; Alam, Aftab; Tu, Yuanyuan; Zhou, Shiguang; Wang, Yanting; Xia, Tao; Huang, Jiangfeng; Li, Ying; Zahoor; Wei, Xiaoyang; Hao, Bo; Peng, Liangcai

    2017-09-01

    In this study, total ten Miscanthus accessions exhibited diverse cell wall compositions, leading to largely varied hexoses yields at 17%-40% (% cellulose) released from direct enzymatic hydrolysis of steam-exploded (SE) residues. Further supplied with 2% Tween-80 into the enzymatic digestion, the Mis7 accession showed the higher hexose yield by 14.8-fold than that of raw material, whereas the Mis10 had the highest hexoses yield at 77% among ten Miscanthus accessions. Significantly, this study identified four wall polymer features that negatively affect biomass saccharification as p<0.05 or 0.01 in the SE residues, including cellulose DP, Xyl and Ara of hemicellulose, and S-monomer of lignin. Based on Simons' stain, the SE porosity (defined by DY/DB) was examined to be the unique positive factor on biomass enzymatic digestion. Hence, this study provides the potential strategy to enhance biomass saccharification using optimal biomass process technology and related genetic breeding in Miscanthus and beyond. Copyright © 2017 Elsevier Ltd. All rights reserved.

  9. Processes for washing a spent ion exchange bed and for treating biomass-derived pyrolysis oil, and apparatuses for treating biomass-derived pyrolysis oil

    Science.gov (United States)

    Baird, Lance Awender; Brandvold, Timothy A.

    2015-11-24

    Processes and apparatuses for washing a spent ion exchange bed and for treating biomass-derived pyrolysis oil are provided herein. An exemplary process for washing a spent ion exchange bed employed in purification of biomass-derived pyrolysis oil includes the step of providing a ion-depleted pyrolysis oil stream having an original oxygen content. The ion-depleted pyrolysis oil stream is partially hydrotreated to reduce the oxygen content thereof, thereby producing a partially hydrotreated pyrolysis oil stream having a residual oxygen content that is less than the original oxygen content. At least a portion of the partially hydrotreated pyrolysis oil stream is passed through the spent ion exchange bed. Water is passed through the spent ion exchange bed after passing at least the portion of the partially hydrotreated pyrolysis oil stream therethrough.

  10. Performance Analysis of an Integrated Fixed Bed Gasifier Model for Different Biomass Feedstocks

    Directory of Open Access Journals (Sweden)

    Sharmina Begum

    2013-12-01

    Full Text Available Energy recovery from biomass by gasification technology has attracted significant interest because it satisfies a key requirement of environmental sustainability by producing near zero emissions. Though it is not a new technology, studies on its integrated process simulation and analysis are limited, in particular for municipal solid waste (MSW gasification. This paper develops an integrated fixed bed gasifier model of biomass gasification using the Advanced System for Process ENngineering (Aspen Plus software for its performance analysis. A computational model was developed on the basis of Gibbs free energy minimization. The model is validated with experimental data of MSW and food waste gasification available in the literature. A reasonable agreement between measured and predicted syngas composition was found. Using the validated model, the effects of operating conditions, namely air-fuel ratio and gasifier temperature, on syngas production are studied. Performance analyses have been done for four different feedstocks, namely wood, coffee bean husks, green wastes and MSWs. The ultimate and proximate analysis data for each feedstock was used for model development. It was found that operating parameters have a significant influence on syngas composition. An air-fuel ratio of 0.3 and gasifier temperature of 700 °C provides optimum performance for a fixed bed gasifier for MSWs, wood wastes, green wastes and coffee bean husks. The developed model can be useful for gasification of other biomasses (e.g., food wastes, rice husks, poultry wastes and sugarcane bagasse to predict the syngas composition. Therefore, the study provides an integrated gasification model which can be used for different biomass feedstocks.

  11. Comparative biochemical analysis after steam pretreatment of lignocellulosic agricultural waste biomass from Williams Cavendish banana plant (Triploid Musa AAA group).

    Science.gov (United States)

    Kamdem, Irénée; Jacquet, Nicolas; Tiappi, Florian Mathias; Hiligsmann, Serge; Vanderghem, Caroline; Richel, Aurore; Jacques, Philippe; Thonart, Philippe

    2015-11-01

    The accessibility of fermentable substrates to enzymes is a limiting factor for the efficient bioconversion of agricultural wastes in the context of sustainable development. This paper presents the results of a biochemical analysis performed on six combined morphological parts of Williams Cavendish Lignocellulosic Biomass (WCLB) after steam cracking (SC) and steam explosion (SE) pretreatments. Solid (S) and liquid (L) fractions (Fs) obtained from SC pretreatment performed at 180°C (SLFSC180) and 210°C (SLFSC210) generated, after diluted acid hydrolysis, the highest proportions of neutral sugar (NS) contents, specifically 52.82 ± 3.51 and 49.78 ± 1.39%w/w WCLB dry matter (DM), respectively. The highest proportions of glucose were found in SFSC210 (53.56 ± 1.33%w/w DM) and SFSC180 (44.47 ± 0.00%w/w DM), while the lowest was found in unpretreated WCLB (22.70 ± 0.71%w/w DM). Total NS content assessed in each LF immediately after SC and SE pretreatments was less than 2%w/w of the LF DM, thus revealing minor acid autohydrolysis consequently leading to minor NS production during the steam pretreatment. WCLB subjected to SC at 210 °C (SC210) generated up to 2.7-fold bioaccessible glucan and xylan. SC and SE pretreatments showed potential for the deconstruction of WCLB (delignification, depolymerization, decrystallization and deacetylation), enhancing its enzymatic hydrolysis. The concentrations of enzymatic inhibitors, such as 2-furfuraldehyde and 5-(hydroxymethyl)furfural from LFSC210, were the highest (41 and 21 µg ml(-1), respectively). This study shows that steam pretreatments in general and SC210 in particular are required for efficient bioconversion of WCLB. Yet, biotransformation through biochemical processes (e.g., anaerobic digestion) must be performed to assess the efficiency of these pretreatments.

  12. Feeding activity of mussels Mytilus edulis related to near-bed currents and phytoplankton biomass

    DEFF Research Database (Denmark)

    Dolmer, Per

    2000-01-01

    The feeding activity of blue mussels Mytilus edulis was investigated in the field and related to near-bottom current velocities and the phytoplankton biomass in the near-bottom water layers for four days. The body content of Chl-a in mussels and their shell gap size were used as indices...... of filtration activity. During days 1 and 2 the near-bed current velocities were low (1.2-2.1 cm s(-1)), and the near-bed phytoplankton biomass was at the same time lower than near the water surface. Between 44 and 69% of the mussels had closed shells and accumulated only small amounts of Chl-a in the body...... rates were estimated from the density of active mussels times the estimated filtration rates (based on the gap size of the mussels and literature values for corresponding filtration rates). Actual population filtration rates ranged from 6.4 to 22.8 m(3) m(-2) d(-1) on days 1 and 3, respectively...

  13. On-line measurement of raw gas elemental composition in fluidized bed biomass steam gasification

    Energy Technology Data Exchange (ETDEWEB)

    Neves, D. [Dept. of Environment and Planning, Centre of Environmental and Marine Studies, Univ. of Aveiro, Campus Universitario de Santiago, Aveiro (Portugal); Dept. of Energy and Environment, Chalmers Univ. of Technology, Goeteborg (Sweden); Thunman, H.; Larsson, A.; Seemann, M. [Dept. of Energy and Environment, Chalmers Univ. of Technology, Goeteborg (Sweden); Tarelho, L.; Matos, A. [Dept. of Environment and Planning, Centre of Environmental and Marine Studies, Univ. of Aveiro, Campus Universitario de Santiago, Aveiro (Portugal)

    2012-11-01

    At the present stage of technology development pursuing to achieve unattended gasification processes, the available methods to determine the CHON composition of raw gas involve a great deal of laboratory tasks, making it unpractical, time-consuming and costly. For instance, there are available analyzers to measure the chemical composition of dry raw gas but offline methods are used to determine the liquids (organic compounds + water). An alternative that is investigated in this work is to convert the raw gas first into simple product species that are easily analyzed. The straightforward way to achieve this is to burn the gas with proper amount of oxygen to assure quantitative conversion into CO{sub 2}, H{sub 2}O and N{sub 2}. This method is demonstrated here by monitoring the CHON composition of raw gas with high temporal resolution from Chalmers 2MW{sub th} FB gasifier.

  14. Heterogeneity of macrozoobenthic assemblages within a Zostera noltii seagrass bed: diversity, abundance, biomass and structuring factors

    Science.gov (United States)

    Blanchet, Hugues; de Montaudouin, Xavier; Lucas, Aurélien; Chardy, Pierre

    2004-09-01

    The macrobenthic fauna community of a 70-km 2Zostera noltii seagrass bed (Arcachon bay, France) was studied by sampling 49 stations systematically. A total of 126 taxa were identified. Cluster Analysis based on χ2 distance showed that in this apparently homogeneous habitat, four distinct macrobenthic communities could be identified. Multiple Discriminant Analysis highlighted the major contribution of the overlying water mass as a forcing variable, and, to a lesser extent, of tidal level and Z. noltii's below-ground parts. Seven stations did not constitute any conspicuous group, and were characterized by a low biomass of leaf (<28 g DW m -2), considered as the lowest value to constitute a Z. noltii community. Less than 24% of the seagrass bed was situated in more oceanic waters and at a quite low tidal level. In this relatively stable environment, the macrofauna community was characterized by a high species richness (mean = 39) and a moderate density and high biomass (12 638 individuals m -2 and 25 g AFDW m -2, respectively). Annelids dominated, particularly the oligochaetes. When physical constraints increased (emersion or brackish water conditions), diversity decreased, abundance and biomass increased. The seagrass bed (55%) was flooded with highly fluctuating waters in term of temperature and salinity, here species richness was low (mean = 27) but abundance and biomass were high (24 384 individuals m -2 and 28 g AFDW m -2, respectively), with a dominance of molluscs. The meadow (7%) was in external waters but at a higher tidal level (2.4 m vs 1.8 m above medium low tide level). This community was characterized by the particularly high density (41 826 individuals m -2) and dominance of oligochaetes (79% of total abundance). Species richness was high (mean = 37) here. A fourth community, extending over 12% of the meadow was dominated by the gastropod Hydrobia ulvae but could not be linked to a specific forcing variable. This study confirmed the almost

  15. Numerical modelling of biomass combustion: Solid conversion processes in a fixed bed furnace

    Science.gov (United States)

    Karim, Md. Rezwanul; Naser, Jamal

    2017-06-01

    Increasing demand for energy and rising concerns over global warming has urged the use of renewable energy sources to carry a sustainable development of the world. Bio mass is a renewable energy which has become an important fuel to produce thermal energy or electricity. It is an eco-friendly source of energy as it reduces carbon dioxide emissions. Combustion of solid biomass is a complex phenomenon due to its large varieties and physical structures. Among various systems, fixed bed combustion is the most commonly used technique for thermal conversion of solid biomass. But inadequate knowledge on complex solid conversion processes has limited the development of such combustion system. Numerical modelling of this combustion system has some advantages over experimental analysis. Many important system parameters (e.g. temperature, density, solid fraction) can be estimated inside the entire domain under different working conditions. In this work, a complete numerical model is used for solid conversion processes of biomass combustion in a fixed bed furnace. The combustion system is divided in to solid and gas phase. This model includes several sub models to characterize the solid phase of the combustion with several variables. User defined subroutines are used to introduce solid phase variables in commercial CFD code. Gas phase of combustion is resolved using built-in module of CFD code. Heat transfer model is modified to predict the temperature of solid and gas phases with special radiation heat transfer solution for considering the high absorptivity of the medium. Considering all solid conversion processes the solid phase variables are evaluated. Results obtained are discussed with reference from an experimental burner.

  16. Kinetic models comparison for steam gasification of coal/biomass blend chars.

    Science.gov (United States)

    Xu, Chaofen; Hu, Song; Xiang, Jun; Yang, Haiping; Sun, Lushi; Su, Sheng; Wang, Baowen; Chen, Qindong; He, Limo

    2014-11-01

    The non-isothermal thermogravimetric method (TGA) was applied to different chars produced from lignite (LN), sawdust (SD) and their blends at the different mass ratios in order to investigate their thermal reactivity under steam atmosphere. Through TGA analysis, it was determined that the most prominent interaction between sawdust and lignite occurred at the mass ratio of sawdust/lignite as 1:4, but with further dose of more sawdust into its blends with lignite, the positive interaction deteriorated due to the agglomeration and deactivation of the alkali mineral involved in sawdust at high steam gasification temperature. Through systematic comparison, it could be observed that the random pore model was the most suitable among the three gas-solid reaction models adopted in this research. Finally, rational kinetic parameters were reached from these gas-solid reaction models, which provided a basis for design and operation of the realistic system of co-gasification of lignite and sawdust in this research.

  17. Effect of SO2 and steam on CO2 capture performance of biomass-templated calcium aluminate pellets.

    Science.gov (United States)

    Erans, María; Beisheim, Theodor; Manovic, Vasilije; Jeremias, Michal; Patchigolla, Kumar; Dieter, Heiko; Duan, Lunbo; Anthony, Edward J

    2016-10-20

    Four types of synthetic sorbents were developed for high-temperature post-combustion calcium looping CO2 capture using Longcal limestone. Pellets were prepared with: lime and cement (LC); lime and flour (LF); lime, cement and flour (LCF); and lime, cement and flour doped with seawater (LCFSW). Flour was used as a templating material. All samples underwent 20 cycles in a TGA under two different calcination conditions. Moreover, the prepared sorbents were tested for 10 carbonation/calcination cycles in a 68 mm-internal-diameter bubbling fluidized bed (BFB) in three environments: with no sulphur and no steam; in the presence of sulphur; and with steam. When compared to limestone, all the synthetic sorbents exhibited enhanced CO2 capture performance in the BFB experiments, with the exception of the sample doped with seawater. In the BFB tests, the addition of cement binder during the pelletisation process resulted in the increase of CO2 capture capacity from 0.08 g CO2 per g sorbent (LF) to 0.15 g CO2 per g sorbent (LCF) by the 10(th) cycle. The CO2 uptake in the presence of SO2 dramatically declined by the 10(th) cycle; for example, from 0.22 g CO2 per g sorbent to 0.05 g CO2 per g sorbent in the case of the untemplated material (LC). However, as expected all samples showed improved performance in the presence of steam, and the decay of reactivity during the cycles was less pronounced. Nevertheless, in the BFB environment, the templated pellets showed poorer CO2 capture performance. This is presumably because of material loss due to attrition under the FB conditions. By contrast, the templated materials performed better than untemplated materials under TGA conditions. This indicates that the reduction of attrition is critical when employing templated materials in realistic systems with FB reactors.

  18. Formation and removal of biomass-derived contaminants in fluidized-bed gasification processes

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E. [VTT Energy, Espoo (Finland). Energy Production Technologies

    1996-12-31

    The objectives of this thesis were to examine the effects of the feedstock and the operating conditions of a fluidized-bed gasifier on the formation of tars and nitrogen-containing compounds and to study the effectiveness of the hot gas cleaning methods developed for the removal of particulates, alkali metals, tars and nitrogen-containing compounds. The most essential part of the work was carried out in the pressurized fluidized-bed gasification test facilities composed of an air-blown bubbling fluidized-bed gasifier and subsequent hot gas filter unit. The operation pressure of the test rig could be varied in the range 0.3 - 1.0 MPa and the maximum allowable gasification temperature was 1 050 deg C. The maximum capacity with biomass fuels was 80 kg/h. A wide range of feedstocks from hard coals, lignite and peat to different wood derived fuels and straw were used in the gasification tests. Two different types of ceramic filters were tested in the filter unit connected to the pressurized fluidized-bed gasifier. The filter unit was operated in a temperature range of 400 - 740 deg C. The particulate removal requirements set by the gas turbines were met by both types of filters and with product gases derived from all the feedstocks tested. In addition to the gasification and gas filtration tests, catalytic tar and ammonia decomposition was studied using both laboratory and bench-scale test facilities. Inexpensive calcium-based bulk materials, dolomites and limestones, were efficient tar decomposition catalysts in atmospheric-pressure tests

  19. Sorption enhanced steam reforming of biomass-derived compounds: process and material

    Energy Technology Data Exchange (ETDEWEB)

    He, Li

    2010-07-01

    An attempt has been made to develop a flexible system to produce very pure H{sub 2} with high efficiency from renewable bio-based recourses. First, such model compounds as ethanol, glycerol, sorbitol and glucose, have been tested for H{sub 2} production via sorption enhanced steam reforming (SESR) over Co-Ni/hydrotalcite-like (HTls) derived catalyst and CaO-based CO{sub 2} acceptor. The experimental results show that all of feedstocks, even heavy feedstocks, were able to offer high H{sub 2} purity (97.3approx99.1%) and yield at low steam to carbon (S/C = 1.3approx6) ratio in comparison to the corresponding steam reforming process. In addition, the studied system also presents encouraging potential for improvement of energy efficiency. Chemical looping combustion (CLC) was coupled to the cyclic multi-step SESR process to assist the acceptor regeneration by using multifunctional Pd/Co-Ni/HTls catalyst. With coupling of CLC to SESR, H{sub 2} concentration in the gas effluent of the SESR reactions was still higher than 95 mol% on a dry basis. The assembled CLC-SESR process has inherent high efficiency in H{sub 2} production. (Author)

  20. Performance Analysis of Solar Assisted Fluidized Bed Dryer Integrated Biomass Furnace with and without Heat Pump for Drying of Paddy

    OpenAIRE

    M. Yahya

    2016-01-01

    The performances of a solar assisted fluidized bed dryer integrated biomass furnace (SA-FBDIBF) and a solar assisted heat pump fluidized bed dryer integrated biomass furnace (SAHP-FBDIBF) for drying of paddy have been evaluated, and also drying kinetics of paddy were determined. The SA-FBDIBF and the SAHP-FBDIBF were used to dry paddy from 11 kg with moisture content of 32.85% db to moisture content of 16.29% db (14% wb) under an air mass flow rate of 0.1037 kg/s within 29.73 minutes and 22.9...

  1. Biomass-Ash-Induced Agglomeration in a Fluidized Bed. Part 1: Experimental Study on the Effects of a Gas Atmosphere

    DEFF Research Database (Denmark)

    Ma, Teng; Fan, Chuigang; Hao, Lifang

    2016-01-01

    . Understanding of the agglomeration in various atmospheres is crucial to optimize the design and operation conditions. This study focuses on the effects of gases on agglomeration tendency with different types of biomass, including corn straw, rice straw, and wheat straw. The biomass ash samples are mixed...... atmospheres are much lower than that in air. It appears that, in a steam atmosphere, the agglomeration of corn straw and rice straw ash is predominantly coating-induced. The agglomeration in both H2 and air atmospheres are melting-induced. In a H2 atmosphere, K2SO4 in the ash samples disappears, caused...

  2. Experimental studies on combustion of composite biomass pellets in fluidized bed.

    Science.gov (United States)

    Guo, Feihong; Zhong, Zhaoping

    2017-12-01

    This work presents studies on the combustion of Composite Biomass Pellets (CBPS) in fluidized bed using bauxite particles as the bed material. Prior to the combustion experiment, cold-flow characterization and thermogravimetric analysis are performed to investigate the effect of air velocity and combustion mechanism of CBPS. The cold-state test shows that CBPs and bauxite particles fluidize well in the fluidized bed. However, because of the presence of large CBPs, optimization of the fluidization velocity is rather challenging. CBPs can gather at the bottom of the fluidized bed at lower gas velocities. On the contrary, when the velocity is too high, they accumulate in the upper section of the fluidized bed. The suitable fluidization velocity for the system in this study was found to be between 1.5-2.0m/s. At the same time, it is found that the critical fluidization velocity and the pressure fluctuation of the two-component system increase with the increase of CBPs mass concentration. The thermogravimetric experiment verifies that the combustion of CBPs is a first-order reaction, and it is divided into three stages: (i) dehydration, (ii) release and combustion of the volatile and (iii) the coke combustion. The combustion of CBPs is mainly based on the stage of volatile combustion, and its activation energy is greater than that of char combustion. During the combustion test, CBPS are burned at a 10kg/h feed rate, while the excess air is varied from 25% to 100%. Temperatures of the bed and flue gas concentrations (O2, CO, SO2 and NO) are recorded. CBPs can be burnt stably, and the temperature of dense phase is maintained at 765-780°C. With the increase of the air velocity, the main combustion region has a tendency to move up. While the combustion is stable, O2 and CO2 concentrations are maintained at about 7%, and 12%, respectively. The concentration of SO2 in the flue gas after the initial stage of combustion is nearly zero. Furthermore, NO concentration is found to

  3. The effect of biomass immobilization support material and bed porosity on hydrogen production in an upflow anaerobic packed-bed bioreactor.

    Science.gov (United States)

    Fernandes, B S; Saavedra, N K; Maintinguer, S I; Sette, L D; Oliveira, V M; Varesche, M B A; Zaiat, M

    2013-07-01

    The aim of this study was to investigate the effect of the support material used for biomass attachment and bed porosity on the potential generation of hydrogen gas in an anaerobic bioreactor treating low-strength wastewater. For this purpose, an upflow anaerobic packed-bed (UAPB) reactor fed with sucrose-based synthetic wastewater was used. Three reactors with various support materials (expanded clay, vegetal coal, and low-density polyethylene) were operated for hydraulic retention time (HRT) of 0.5 and 2 h. Based on the results obtained, three further reactors were operated with low-density polyethylene as a material support using various bed porosities (91, 75, and 50 %) for an HRT of 0.5 h. The UAPB reactor was found to be a feasible technology for hydrogen production, reaching a maximum substrate-based hydrogen yield of 7 mol H₂ mol(-1) sucrose for an HRT of 0.5 h. The type of support material used did not affect hydrogen production or the microbial population inside the reactor. Increasing the bed porosity to 91 % provided a continuous and cyclic production of hydrogen, whereas the lower bed porosities resulted in a reduced time of hydrogen production due to biomass accumulation, which resulted in a decreasing working volume.

  4. DETERMINATION OF PARTICLE DENSITY BY MERCURY POROSIMETRY FOR BIOMASS FLUID DYNAMIC STUDY IN MOVING BEDS

    Directory of Open Access Journals (Sweden)

    Juan F. Saldarriaga

    2014-06-01

    Full Text Available Determination of the particle density is required to address the hydrodynamic study of a moving bed contactor. The measurement of this parameter is complicated when particles are irregularly shaped. In this study, two different techniques were use: compaction by mechanical compression and an alternative proposal, which contemplates the potential of mercury porosimetry for determining the surface and structural properties. It was observed that the results obtained by compacting in all cases are higher than expected. However, the values obtained by mercury porosimetry are more consistent with expected values. For example in the sawdust valued at 500kg/m3, very similar to the value of the original wood (502kg/m3. Values obtained by this procedure adequately represent the relationship between mass and volume of the particle and therefore are valid for hydrodynamic characterization of the biomass.

  5. Hydrodynamics of Biomass Gasification in a Dual Chamber Circulating Fluidized Bed Reactor

    Directory of Open Access Journals (Sweden)

    Wahyu Haifa

    2016-01-01

    Full Text Available This paper presents work on hydrodynamics of several types of biomass mixture in a dual chamber circulating fluidized bed. In designing the CFBreactornecessary to know the distribution of solid particles radially and axially influenced by fluidizing gas velocity, particle size, solid circulation flux, reactor diameter and height of the reactor. These factors will affect pressure drop along the riser of the reaction chamber. Pressure drop is an important factor in the study of hydrodynamics of particle flow. The pressure drop was measured using mathematical model compared to experimental results done on a cold mode. Since it was found that both results were consistent which means that the model can be used to predict the operating parameters of CFB design.

  6. Gasification of biomass in a fixed bed downdraft gasifier--a realistic model including tar.

    Science.gov (United States)

    Barman, Niladri Sekhar; Ghosh, Sudip; De, Sudipta

    2012-03-01

    This study presents a model for fixed bed downdraft biomass gasifiers considering tar also as one of the gasification products. A representative tar composition along with its mole fractions, as available in the literature was used as an input parameter within the model. The study used an equilibrium approach for the applicable gasification reactions and also considered possible deviations from equilibrium to further upgrade the equilibrium model to validate a range of reported experimental results. Heat balance was applied to predict the gasification temperature and the predicted values were compared with reported results in literature. A comparative study was made with some reference models available in the literature and also with experimental results reported in the literature. Finally a predicted variation of performance of the gasifier by this validated model for different air-fuel ratio and moisture content was also discussed.

  7. Thermodynamic simulation of biomass gas steam reforming for a solid oxide fuel cell (SOFC system

    Directory of Open Access Journals (Sweden)

    A. Sordi

    2009-12-01

    Full Text Available This paper presents a methodology to simulate a small-scale fuel cell system for power generation using biomass gas as fuel. The methodology encompasses the thermodynamic and electrochemical aspects of a solid oxide fuel cell (SOFC, as well as solves the problem of chemical equilibrium in complex systems. In this case the complex system is the internal reforming of biomass gas to produce hydrogen. The fuel cell input variables are: operational voltage, cell power output, composition of the biomass gas reforming, thermodynamic efficiency, electrochemical efficiency, practical efficiency, the First and Second law efficiencies for the whole system. The chemical compositions, molar flows and temperatures are presented to each point of the system as well as the exergetic efficiency. For a molar water/carbon ratio of 2, the thermodynamic simulation of the biomass gas reforming indicates the maximum hydrogen production at a temperature of 1070 K, which can vary as a function of the biomass gas composition. The comparison with the efficiency of simple gas turbine cycle and regenerative gas turbine cycle shows the superiority of SOFC for the considered electrical power range.

  8. Steam reforming of n-hexane on pellet and monolithic catalyst beds. A comparative study on improvements due to heat transfer

    Science.gov (United States)

    1981-01-01

    Monolithic catalysts with higher available active surface areas and better thermal conductivity than conventional pellets beds, making possible the steam reforming of fuels heavier than naphtha, were examined. Performance comparisons were made between conventional pellet beds and honeycomb monolith catalysts using n-hexane as the fuel. Metal-supported monoliths were examined. These offer higher structural stability and higher thermal conductivity than ceramic supports. Data from two metal monoliths of different nickel catalyst loadings were compared to pellets under the same operating conditions. Improved heat transfer and better conversion efficiencies were obtained with the monolith having higher catalyst loading. Surface-gas interaction was observed throughout the length of the monoliths.

  9. Secondary Waste Form Screening Test Results—THOR® Fluidized Bed Steam Reforming Product in a Geopolymer Matrix

    Energy Technology Data Exchange (ETDEWEB)

    Pires, Richard P.; Westsik, Joseph H.; Serne, R. Jeffrey; Mattigod, Shas V.; Golovich, Elizabeth C.; Valenta, Michelle M.; Parker, Kent E.

    2011-07-14

    Screening tests are being conducted to evaluate waste forms for immobilizing secondary liquid wastes from the Hanford Tank Waste Treatment and Immobilization Plant (WTP). Plans are underway to add a stabilization treatment unit to the Effluent Treatment Facility to provide the needed capacity for treating these wastes from WTP. The current baseline is to use a Cast Stone cementitious waste form to solidify the wastes. Through a literature survey, DuraLith alkali-aluminosilicate geopolymer, fluidized-bed steam reformation (FBSR) granular product encapsulated in a geopolymer matrix, and a Ceramicrete phosphate-bonded ceramic were identified both as candidate waste forms and alternatives to the baseline. These waste forms have been shown to meet waste disposal acceptance criteria, including compressive strength and universal treatment standards for Resource Conservation and Recovery Act (RCRA) metals (as measured by the toxicity characteristic leaching procedure [TCLP]). Thus, these non-cementitious waste forms should also be acceptable for land disposal. Information is needed on all four waste forms with respect to their capability to minimize the release of technetium. Technetium is a radionuclide predicted to be in the secondary liquid wastes in small quantities, but the Integrated Disposal Facility (IDF) risk assessment analyses show that technetium, even at low mass, produces the largest contribution to the estimated IDF disposal impacts to groundwater.

  10. Application of Scaling-Law and CFD Modeling to Hydrodynamics of Circulating Biomass Fluidized Bed Gasifier

    Directory of Open Access Journals (Sweden)

    Mazda Biglari

    2016-06-01

    Full Text Available Two modeling approaches, the scaling-law and CFD (Computational Fluid Dynamics approaches, are presented in this paper. To save on experimental cost of the pilot plant, the scaling-law approach as a low-computational-cost method was adopted and a small scale column operating under ambient temperature and pressure was built. A series of laboratory tests and computer simulations were carried out to evaluate the hydrodynamic characteristics of a pilot fluidized-bed biomass gasifier. In the small scale column solids were fluidized. The pressure and other hydrodynamic properties were monitored for the validation of the scaling-law application. In addition to the scaling-law modeling method, the CFD approach was presented to simulate the gas-particle system in the small column. 2D CFD models were developed to simulate the hydrodynamic regime. The simulation results were validated with the experimental data from the small column. It was proved that the CFD model was able to accurately predict the hydrodynamics of the small column. The outcomes of this research present both the scaling law with the lower computational cost and the CFD modeling as a more robust method to suit various needs for the design of fluidized-bed gasifiers.

  11. Tar reduction in pyrolysis vapours from biomass over a hot char bed.

    Science.gov (United States)

    Gilbert, P; Ryu, C; Sharifi, V; Swithenbank, J

    2009-12-01

    The behaviour of pyrolysis vapours over char was investigated in order to maximise tar conversion for the development of a new fixed bed gasifier. Wood samples were decomposed at a typical pyrolysis temperature (500 degrees C) and the pyrolysis vapours were then passed directly through a tar cracking zone in a tubular reactor. The product yields and properties of the condensable phases and non-condensable gases were studied for different bed lengths of char (0-450 mm), temperatures (500-800 degrees C), particle sizes (10 and 15 mm) and nitrogen purge rates (1.84-14.70 mm/s). The carbon in the condensable phases showed about 66% reduction by a 300 mm long char section at 800 degrees C, compared to that for pyrolysis at 500 degrees C. The amount of heavy condensable phase decreased with increasing temperature from about 18.4 wt% of the biomass input at 500 degrees C to 8.0 wt% at 800 degrees C, forming CO, H(2) and other light molecules. The main mode of tar conversion was found to be in the vapour phase when compared to the results without the presence of char. The composition of the heavy condensable phase was simplified into much fewer secondary and tertiary tar components at 800 degrees C. Additional measures were required to maximise the heterogeneous effect of char for tar reduction.

  12. Simulated moving bed separation of agarose-hydrolyzate components for biofuel production from marine biomass.

    Science.gov (United States)

    Kim, Pung-Ho; Nam, Hee-Geun; Park, Chanhun; Wang, Nien-Hwa Linda; Chang, Yong Keun; Mun, Sungyong

    2015-08-07

    The economically-efficient separation of galactose, levulinic acid (LA), and 5-hydroxymethylfurfural (5-HMF) in acid hydrolyzate of agarose has been a key issue in the area of biofuel production from marine biomass. To address this issue, an optimal simulated moving bed (SMB) process for continuous separation of the three agarose-hydrolyzate components with high purities, high yields, and high throughput was developed in this study. As a first step for this task, the adsorption isotherm and mass-transfer parameters of each component on the qualified adsorbent were determined through a series of multiple frontal experiments. The determined parameters were then used in optimizing the SMB process for the considered separation. Finally, the optimized SMB process was tested experimentally using a self-assembled SMB unit with four zones. The SMB experimental results and the relevant computer simulations verified that the developed process in this study was quite successful in the economically-efficient separation of galactose, LA, and 5-HMF in a continuous mode with high purities and high yields. It is thus expected that the developed SMB process in this study will be able to serve as one of the trustworthy ways of improving the economic feasibility of biofuel production from marine biomass. Copyright © 2015 Elsevier B.V. All rights reserved.

  13. Development of novel fixed-bed gasification methods for biomass residues and agrobiofuels; Kiinteaekerroskaasutustekniikan kehitys biopolttoaineille

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Staahlberg, P.; Simell, P. [VTT Energy, Espoo (Finland)

    1998-12-31

    The overall aims of this project were: (1) to show that fixed-bed gasifiers can be designed to operate reliably with realistically available woody residues and energy crops, (2) to develop catalytic gas cleaning technique for engine use, and (3) to find suitable markets where the local conditions are favourable for economically competitive small-scale power and heat production based on this technology. The specific objectives of the project are: (a) To define the requirements to the feedstock quality needed to guarantee reliable operation with respect to fuel flow, pressure drop, ash sintering and tar formation in an existing commercial downdraft gasifier; (b) To collect operation experience from the commercial Bioneer updraft gasifiers in order to update earlier pilot-plant findings of VTT (Technical Research Centre of Finland) concerning the requirements for feedstock quality required for long-term reliable operation in this reactor type; (c) To develop and test a new type of fixed-bed gasifies design, which is based on forced fuel flow and consequently allows the use of low-bulk-density fuels; (d) To develop and test on a PDU scale a simple and reliable secondary catalytic reactor required for complete decomposition of tars, and (e) To evaluate the economic feasibility of different fixed-bed gasification systems on a potential local energy production market (low-cost biomass residues available, high cost of external energy). The work is carried out as an EC/Joule 3 project in close co-operation between the following partners: VTT Energy and Condens Oy of Finland and Finesport Engineering and Antiche Terre soc. coop.r.l of Italy. VTT Energy co-ordinates the project. The work programme is scheduled to be carried out during the period of 1 October 1997 - 30 September 1999

  14. Development of novel fixed-bed gasification methods for biomass residues and agrobiofuels

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Staahlberg, P.; Simell, P. [VTT Energy, Espoo (Finland)

    1998-12-01

    The general goals of the project are: (1) to show that fixed-bed gasifiers can be designed to operate reliably with realistically available woody residues and energy crops, (2) to develop catalytic gas cleaning for producing clean gas to the engine use, and (3) to find suitable markets where the local conditions are favorable for economically competitive small-scale power and heat production based on this technology. The specific goals of the project are: to define the requirements to the feedstock quality needed to guarantee reliable operation with respect to the fuel flow, pressure drop, ash sintering and tar formation in an existing commercial downdraft gasifier; to collect experience from the commercial Bioneer updraft gasifiers in order to update earlier pilot-plant findings of VTT concerning requirements for feedstock quality required for long-term reliable operation in this reactor type; to develop and test a new type of the fixed-bed gasifier design, based on forced fuel flow and which consequently allows the use of the low bulk-density fuels; to develop and test on a PDU-scale a simple and reliable secondary catalytic reactor required for complete decomposition of tars; and to evaluate the economic feasibility of different fixed bed gasification systems on a potential local energy production market (low-cost biomass residues available, high cost of external energy). The work is carried out as an EC/Joule 3 project in close co-operation between the following partners: VTT Energy and Condens Oy from Finland, Finesport Engineering and Antiche Terre soc. coop.r.l from Italy. VTT energy coordinates the project. The work programme is scheduled to be carried out during the period Oct. 1st 1997 - Sep. 30th 1999 6 refs. Bioenergy Research programme

  15. Media arrangement impacts cell growth in anaerobic fixed-bed reactors treating sugarcane vinasse: Structured vs. randomic biomass immobilization.

    Science.gov (United States)

    de Aquino, Samuel; Fuess, Lucas Tadeu; Pires, Eduardo Cleto

    2017-07-01

    This study reports on the application of an innovative structured-bed reactor (FVR) as an alternative to conventional packed-bed reactors (PBRs) to treat high-strength solid-rich wastewaters. Using the FVR prevents solids from accumulating within the fixed-bed, while maintaining the advantages of the biomass immobilization. The long-term operation (330days) of a FVR and a PBR applied to sugarcane vinasse under increasing organic loads (2.4-18.0kgCODm(-3)day(-1)) was assessed, focusing on the impacts of the different media arrangements over the production and retention of biomass. Much higher organic matter degradation rates, as well as long-term operational stability and high conversion efficiencies (>80%) confirmed that the FVR performed better than the PBR. Despite the equivalent operating conditions, the biomass growth yield was different in both reactors, i.e., 0.095gVSSg(-1)COD (FVR) and 0.066gVSSg(-1)COD (PBR), indicating a clear control of the media arrangement over the biomass production in fixed-bed reactors. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Hydrogen production via catalytic steam reforming of fast pyrolysis bio-oil in a two-stage fixed bed reactor system

    Energy Technology Data Exchange (ETDEWEB)

    Wu, C.; Huang, Q.; Sui, M.; Yan, Y.; Wang, F. [Research Center for Biomass Energy, State Key Laboratory of Bioreactor Engineering, East China University of Science and Technology, Shanghai 200237 (China)

    2008-12-15

    Hydrogen production was prepared via catalytic steam reforming of fast pyrolysis bio-oil in a two-stage fixed bed reactor system. Low-cost catalyst dolomite was chosen for the primary steam reforming of bio-oil in consideration of the unavoidable deactivation caused by direct contact of metal catalyst and bio-oil itself. Nickel-based catalyst Ni/MgO was used in the second stage to increase the purity and the yield of desirable gas product further. Influential parameters such as temperature, steam to carbon ratio (S/C, S/CH{sub 4}), and material space velocity (W{sub B}HSV, GHSV) both for the first and the second reaction stages on gas product yield, carbon selectivity of gas product, CH{sub 4} conversion as well as purity of desirable gas product were investigated. High temperature (> 850 C) and high S/C (> 12) are necessary for efficient conversion of bio-oil to desirable gas product in the first steam reforming stage. Low W{sub B}HSV favors the increase of any gas product yield at any selected temperature and the overall conversion of bio-oil to gas product increases accordingly. Nickel-based catalyst Ni/MgO is effective in purification stage and 100% conversion of CH{sub 4} can be obtained under the conditions of S/CH{sub 4} no less than 2 and temperature no less than 800 C. Low GHSV favors the CH{sub 4} conversion and the maximum CH{sub 4} conversion 100%, desirable gas product purity 100%, and potential hydrogen yield 81.1% can be obtained at 800 C provided that GHSV is no more than 3600 h{sup -} {sup 1}. Carbon deposition behaviors in one-stage reactor prove that the steam reforming of crude bio-oil in a two-stage fixed bed reaction system is necessary and significant. (author)

  17. Simulation of biomass steam-gasification%生物质蒸汽气化模拟研究

    Institute of Scientific and Technical Information of China (English)

    王辉

    2013-01-01

    Based on chemical thermodynamic software of GasEQ, this study investigated the influence of H2, CH4 and CO in syngas composition by temperature, ratio of steam to biomass (S/M) and concentration of carbon dioxide (CO2). Low heat value of cold syngas (LHV) and heat conversion efficiency (q), especially the external heat supply during q calculation were also accounted. The results of simulation showed: LHV generally decreased with the increasing temperature, and q was significantly up then slightly down. An optimistic temperature for steam-gasification was assumed in the range of 800~900 ℃. With higher S/M, more H2 was produced, and the percentage of H2 was higher in syngas, while LHV was reduced, and q likely first increased and then decreased with the increasing of steam. So a most economic value of S/M (0.6) possibly existed in real process. When CO2 was added into reagent gas, less char was remained in products, higher content of CO and lower percentage of H2 were observed in the cold syngas.%利用化学热力学软件(GasEQ)模拟了生物质蒸汽气化过程中温度、水蒸气与物料质量比(S/M)以及CO2浓度对H2,CH4和CO的影响;研究了冷合成气低位热值(LHV)和气化能量转化效率(q)随各参数变化的规律,并且考虑了外部能量的消耗.模拟研究得到:随着温度的升高,合成气的LHV总体表现出降低,并且q先增加后微弱下降,认为存在一个最优的气化温度(800~900℃);高/M有利于H2的生成,提高H2的体积浓度,但水蒸气的增加,降低了LHV值,并且q先增加后减少,因为水蒸气会消耗大量外部能量,存在一个最经济的气化S/M;随着反应气中CO2浓度的升高,促进了生物质气化,并使CO浓度升高和H2浓度降低.

  18. Flash Pyrolysis and Fractional Pyrolysis of Oleaginous Biomass in a Fluidized-bed Reactor

    Science.gov (United States)

    Urban, Brook

    Thermochemical conversion methods such as pyrolysis have the potential for converting diverse biomass feedstocks into liquid fuels. In particular, bio-oil yields can be maximized by implementing flash pyrolysis to facilitate rapid heat transfer to the solids along with short vapor residence times to minimize secondary degradation of bio-oils. This study first focused on the design and construction of a fluidized-bed flash pyrolysis reactor with a high-efficiency bio-oil recovery unit. Subsequently, the reactor was used to perform flash pyrolysis of soybean pellets to assess the thermochemical conversion of oleaginous biomass feedstocks. The fluidized bed reactor design included a novel feed input mechanism through suction created by flow of carrier gas through a venturi which prevented plugging problems that occur with a more conventional screw feeders. In addition, the uniquely designed batch pyrolysis unit comprised of two tubes of dissimilar diameters. The bottom section consisted of a 1" tube and was connected to a larger 3" tube placed vertically above. At the carrier gas flow rates used in these studies, the feed particles remained fluidized in the smaller diameter tube, but a reduction in carrier gas velocity in the larger diameter "disengagement chamber" prevented the escape of particles into the condensers. The outlet of the reactor was connected to two Allihn condensers followed by an innovative packed-bed dry ice condenser. Due to the high carrier gas flow rates in fluidized bed reactors, bio-oil vapors form dilute aerosols upon cooling which that are difficult to coalesce and recover by traditional heat exchange condensers. The dry ice condenser provided high surface area for inertial impaction of these aerosols and also allowed easy recovery of bio-oils after natural evaporation of the dry ice at the end of the experiments. Single step pyrolysis was performed between 250-610°C with a vapor residence time between 0.3-0.6s. At 550°C or higher, 70% of

  19. FLUIDIZED BED STEAM REFORMING MINERALIZATION FOR HIGH ORGANIC AND NITRATE WASTE STREAMS FOR THE GLOBAL NUCLEAR ENERGY PARTNERSHIP

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Michael Williams, M

    2008-01-11

    Waste streams that may be generated by the Global Nuclear Energy Partnership (GNEP) Advanced Energy Initiative may contain significant quantities of organics (0-53 wt%) and/or nitrates (0-56 wt%). Decomposition of high nitrate streams requires reducing conditions, e.g. organic additives such as sugar or coal, to reduce the NO{sub x} in the off-gas to N{sub 2} to meet the Clean Air Act (CAA) standards during processing. Thus, organics will be present during waste form stabilization regardless of which GNEP processes are chosen, e.g. organics in the feed or organics for nitrate destruction. High organic containing wastes cannot be stabilized with the existing HLW Best Developed Available Technology (BDAT) which is HLW vitrification (HLVIT) unless the organics are removed by preprocessing. Alternative waste stabilization processes such as Fluidized Bed Steam Reforming (FBSR) operate at moderate temperatures (650-750 C) compared to vitrification (1150-1300 C). FBSR converts organics to CAA compliant gases, creates no secondary liquid waste streams, and creates a stable mineral waste form that is as durable as glass. For application to the high Cs-137 and Sr-90 containing GNEP waste streams a single phase mineralized Cs-mica phase was made by co-reacting illite clay and GNEP simulated waste. The Cs-mica accommodates up to 30% wt% Cs{sub 2}O and all the GNEP waste species, Ba, Sr, Rb including the Cs-137 transmutation to Ba-137. For reference, the cesium mineral pollucite (CsAlSi{sub 2}O{sub 6}), currently being studied for GNEP applications, can only be fabricated at {ge} 1000 C. Pollucite mineralization creates secondary aqueous waste streams and NO{sub x}. Pollucite is not tolerant of high concentrations of Ba, Sr or Rb and forces the divalent species into different mineral host phases. The pollucite can accommodate up to 33% wt% Cs{sub 2}O.

  20. RADIOACTIVE DEMONSTRATIONS OF FLUIDIZED BED STEAM REFORMING WITH ACUTAL HANFORD LOW ACTIVITY WASTES VERIFYING FBSR AS A SUPPLEMENTARY TREATMENT

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C.; Crawford, C.; Burket, P.; Bannochie, C.; Daniel, G.; Nash, C.; Cozzi, A.; Herman, C.

    2012-01-12

    The U.S. Department of Energy's Office of River Protection is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level waste (HLW) and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the cleanup mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA). Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. Fluidized Bed Steam Reforming (FBSR) is one of the supplementary treatments being considered. FBSR offers a moderate temperature (700-750 C) continuous method by which LAW and other secondary wastes can be processed irrespective of whether they contain organics, nitrates/nitrites, sulfates/sulfides, chlorides, fluorides, and/or radio-nuclides like I-129 and Tc-99. Radioactive testing of Savannah River LAW (Tank 50) shimmed to resemble Hanford LAW and actual Hanford LAW (SX-105 and AN-103) have produced a ceramic (mineral) waste form which is the same as the non-radioactive waste simulants tested at the engineering scale. The radioactive testing demonstrated that the FBSR process can retain the volatile radioactive components that cannot be contained at vitrification temperatures. The radioactive and nonradioactive mineral waste forms that were produced by co-processing waste with kaolin clay in an FBSR process are shown to be as durable as LAW glass.

  1. Bubbling bed catalytic hydropyrolysis process utilizinig larger catalyst particles and small biomass particles featuring an anti-slugging reactor

    Energy Technology Data Exchange (ETDEWEB)

    Marker, Terry L.; Felix, Larry G.; Linck, Martin B.; Roberts, Michael J.

    2016-12-06

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  2. Bubbling bed catalytic hydropyrolysis process utilizing larger catalyst particles and smaller biomass particles featuring an anti-slugging reactor

    Science.gov (United States)

    Marker, Terry L; Felix, Larry G; Linck, Martin B; Roberts, Michael J

    2014-09-23

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  3. Bubbling bed catalytic hydropyrolysis process utilizinig larger catalyst particles and small biomass particles featuring an anti-slugging reactor

    Science.gov (United States)

    Marker, Terry L.; Felix, Larry G.; Linck, Martin B.; Roberts, Michael J.

    2016-12-06

    This invention relates to a process for thermochemically transforming biomass or other oxygenated feedstocks into high quality liquid hydrocarbon fuels. In particular, a catalytic hydropyrolysis reactor, containing a deep bed of fluidized catalyst particles is utilized to accept particles of biomass or other oxygenated feedstocks that are significantly smaller than the particles of catalyst in the fluidized bed. The reactor features an insert or other structure disposed within the reactor vessel that inhibits slugging of the bed and thereby minimizes attrition of the catalyst. Within the bed, the biomass feedstock is converted into a vapor-phase product, containing hydrocarbon molecules and other process vapors, and an entrained solid char product, which is separated from the vapor stream after the vapor stream has been exhausted from the top of the reactor. When the product vapor stream is cooled to ambient temperatures, a significant proportion of the hydrocarbons in the product vapor stream can be recovered as a liquid stream of hydrophobic hydrocarbons, with properties consistent with those of gasoline, kerosene, and diesel fuel. Separate streams of gasoline, kerosene, and diesel fuel may also be obtained, either via selective condensation of each type of fuel, or via later distillation of the combined hydrocarbon liquid.

  4. Effect of small-scale biomass gasification at the state of refractory lining the fixed bed reactor

    Energy Technology Data Exchange (ETDEWEB)

    Janša, Jan, E-mail: jan.jansa@vsb.cz; Peer, Vaclav, E-mail: vaclav.peer@vsb.cz; Pavloková, Petra, E-mail: petra.pavlokova@vsb.cz [VŠB – Technical University of Ostrava, Energy Research Center, 708 33 Ostrava (Czech Republic)

    2016-06-30

    The article deals with the influence of biomass gasification on the condition of the refractory lining of a fixed bed reactor. The refractory lining of the gasifier is one part of the device, which significantly affects the operational reliability and durability. After removing the refractory lining of the gasifier from the experimental reactor, there was done an assessment how gasification of different kinds of biomass reflected on its condition in terms of the main factors affecting its life. Gasification of biomass is reflected on the lining, especially through sticking at the bottom of the reactor. Measures for prolonging the life of lining consist in the reduction of temperature in the reactor, in this case, in order to avoid ash fusion biomass which it is difficult for this type of gasifier.

  5. EFFECTS OF NUTRIENT ENRICHMENT ON PRIMARY PRODUCTION AND BIOMASS OF SEDIMENT MICROALGAE IN A SUBTROPICAL SEAGRASS BED(1).

    Science.gov (United States)

    Bucolo, Philip; Sullivan, Michael J; Zimba, Paul V

    2008-08-01

    Eutrophication of coastal waters often leads to excessive growth of microalgal epiphytes attached to seagrass leaves; however, the effect of increased nutrient levels on sediment microalgae has not been studied within seagrass communities. A slow-release NPK Osmocote fertilizer was added to sediments within and outside beds of the shoal grass Halodule wrightii, in Big Lagoon, Perdido Key, Florida. Gross primary production (GPP) and biomass (HPLC photopigments) of sediment microalgae within and adjacent to fertilized and control H. wrightii beds were measured following two 4-week enrichment periods during June and July 2004. There was no effect of position on sediment microalgal GPP or biomass in control and enriched plots. However, nutrient enrichment significantly increased GPP in both June and July. These results suggest that sediment microalgae could fill some of the void in primary production where seagrass beds disappear due to excessive nutrient enrichment. Sedimentary chl a (proxy of total microalgal biomass) significantly increased only during the June enrichment period, whereas fucoxanthin (proxy of total diatom biomass) was not increased by nutrient enrichment even though its concentration doubled in the enriched plots in June.

  6. Review on Biomass Torrefaction Process and Product Properties and Design of Moving Bed Torrefaction System Model Development

    Energy Technology Data Exchange (ETDEWEB)

    Jaya Shankar Tumuluru; Christopher T. Wright; Shahab Sokhansanj

    2011-08-01

    A Review on Torrefaction Process and Design of Moving Bed Torrefaction System for Biomass Processing Jaya Shankar Tumuluru1, Shahab Sokhansanj2 and Christopher T. Wright1 Idaho National Laboratory Biofuels and Renewable Energy Technologies Department Idaho Falls, Idaho 83415 Oak Ridge National Laboratory Bioenergy Resource and Engineering Systems Group Oak Ridge, TN 37831 Abstract Torrefaction is currently developing as an important preprocessing step to improve the quality of biomass in terms of physical properties, and proximate and ultimate composition. Torrefaction is a slow heating of biomass in an inert or reduced environment to a maximum temperature of 300 C. Torrefaction can also be defined as a group of products resulting from the partially controlled and isothermal pyrolysis of biomass occurring in a temperature range of 200-230 C and 270-280 C. Thus, the process can also be called a mild pyrolysis as it occurs at the lower temperature range of the pyrolysis process. At the end of the torrefaction process, a solid uniform product with lower moisture content and higher energy content than raw biomass is produced. Most of the smoke-producing compounds and other volatiles are removed during torrefaction, which produces a final product that will have a lower mass but a higher heating value. There is a lack of literature on the design aspects of torrefaction reactor and a design sheet for estimating the dimensions of the torrefier based on capacity. This study includes (a) conducting a detailed review on the torrefaction of biomass in terms of understanding the process, product properties, off-gas compositions, and methods used, and (b) to design a moving bed torrefier, taking into account the basic fundamental heat and mass transfer calculations. Specific objectives include calculating the dimensions like diameter and height of the moving packed bed torrefier for different capacities ranging from 25-1000 kg/hr, designing the heat loads and gas flow rates, and

  7. Steam reforming of biomass gasification tar using benzene as a model compound over various Ni supported metal oxide catalysts.

    Science.gov (United States)

    Park, Hyun Ju; Park, Sung Hoon; Sohn, Jung Min; Park, Junhong; Jeon, Jong-Ki; Kim, Seung-Soo; Park, Young-Kwon

    2010-01-01

    The steam reforming of benzene as a model compound of biomass gasification tar was carried out over various Ni/metal oxide catalysts. The effects of the support, temperature, Ni-precursor, Ni loading and reaction time were examined, and their catalytic performance was compared with that of a commercial Ni catalyst. Among the Ni/metal oxide catalysts used, 15 wt% Ni/CeO(2)(75%)-ZrO(2)(25%) showed the highest catalytic performance owing to its greater redox characteristics and increased surface area, irrespective of the reaction temperature. The catalytic activity of 15 wt% Ni/CeO(2)(75%)-ZrO(2)(25%) was higher than that of the commercial Ni catalyst. Moreover, the catalyst activity was retained due to its excellent resistance to coke deposition even after 5h. The Ni-precursor played a critical role in the catalytic activity. With the exception of nickel nitrate, all the Ni-precursors (chloride and sulfate) caused deactivation of the catalyst.

  8. Cultivation of a native alga for biomass and biofuel accumulation in coal bed methane production water

    Science.gov (United States)

    Hodgskiss, Logan H.; Nagy, Justin; Barnhart, Elliott P.; Cunningham, Alfred B.; Fields, Matthew W.

    2016-01-01

    Coal bed methane (CBM) production has resulted in thousands of ponds in the Powder River Basin of low-quality water in a water-challenged region. A green alga isolate, PW95, was isolated from a CBM production pond, and analysis of a partial ribosomal gene sequence indicated the isolate belongs to the Chlorococcaceae family. Different combinations of macro- and micronutrients were evaluated for PW95 growth in CBM water compared to a defined medium. A small level of growth was observed in unamended CBM water (0.15 g/l), and biomass increased (2-fold) in amended CBM water or defined growth medium. The highest growth rate was observed in CBM water amended with both N and P, and the unamended CBM water displayed the lowest growth rate. The highest lipid content (27%) was observed in CBM water with nitrate, and a significant level of lipid accumulation was not observed in the defined growth medium. Growth analysis indicated that nitrate deprivation coincided with lipid accumulation in CBM production water, and lipid accumulation did not increase with additional phosphorus limitation. The presented results show that CBM production wastewater can be minimally amended and used for the cultivation of a native, lipid-accumulating alga.

  9. Fast co-pyrolysis of biomass and lignite in a micro fluidized bed reactor analyzer.

    Science.gov (United States)

    Mao, Yebing; Dong, Lei; Dong, Yuping; Liu, Wenping; Chang, Jiafu; Yang, Shuai; Lv, Zhaochuan; Fan, Pengfei

    2015-04-01

    The co-pyrolysis characteristic of biomass and lignite were investigated in a Micro Fluidized Bed Reaction Analyzer under isothermal condition. The synergetic effect was evaluated by comparing the experimental gas yields and distributions with the calculated values, and iso-conversional method was used to calculate the kinetic parameters of formation of each gas component. The results showed that synergetic effect was manifested in co-pyrolysis. For the range of conversion investigated, the activation energies for H2, CH4, CO and CO2 were 72.90 kJ/mol, 43.90 kJ/mol, 18.51 kJ/mol and 13.44 kJ/mol, respectively; the reactions for CH4 and CO2 conformed to 2 order chemical reaction model, and for H2 and CO conformed to 1.5 order chemical reaction model; the pre-exponential factors for CH4, CO2, H2 and CO were 249.0 S(-1), 5.290 S(-1), 237.4 S(-1) and 2.693 S(-1), respectively. The discrepancy of the kinetic parameters implied that there were different pathways for forming the different gas.

  10. Energy from Biomass for Conversion of Biomass

    Science.gov (United States)

    Abolins, J.; Gravitis, J.

    2009-01-01

    Along with estimates of minimum energy required by steam explosion pre-treatment of biomass some general problems concerning biomass conversion into chemicals, materials, and fuels are discussed. The energy necessary for processing biomass by steam explosion auto-hydrolysis is compared with the heat content of wood and calculated in terms of the amount of saturated steam consumed per unit mass of the dry content of wood biomass. The fraction of processed biomass available for conversion after steam explosion pre-treatment is presented as function of the amount of steam consumed per unit mass of the dry content of wood. The estimates based on a simple model of energy flows show the energy required by steam explosion pre-treatment of biomass being within 10% of the heat content of biomass - a realistic amount demonstrating that energy for the process can be supplied from a reasonable proportion of biomass used as the source of energy for steam explosion pre-treatment.

  11. MINERALIZATION OF RADIOACTIVE WASTES BY FLUIDIZED BED STEAM REFORMING (FBSR): COMPARISONS TO VITREOUS WASTE FORMS, AND PERTINENT DURABILITY TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C

    2008-12-26

    The Savannah River National Laboratory (SRNL) was requested to generate a document for the Washington State Department of Ecology and the U.S. Environmental Protection Agency that would cover the following topics: (1) A description of the mineral structures produced by Fluidized Bed Steam Reforming (FBSR) of Hanford type Low Activity Waste (LAW including LAWR which is LAW melter recycle waste) waste, especially the cage structured minerals and how they are formed. (2) How the cage structured minerals contain some contaminants, while others become part of the mineral structure (Note that all contaminants become part of the mineral structure and this will be described in the subsequent sections of this report). (3) Possible contaminant release mechanisms from the mineral structures. (4) Appropriate analyses to evaluate these release mechanisms. (5) Why the appropriate analyses are comparable to the existing Hanford glass dataset. In order to discuss the mineral structures and how they bond contaminants a brief description of the structures of both mineral (ceramic) and vitreous waste forms will be given to show their similarities. By demonstrating the similarities of mineral and vitreous waste forms on atomic level, the contaminant release mechanisms of the crystalline (mineral) and amorphous (glass) waste forms can be compared. This will then logically lead to the discussion of why many of the analyses used to evaluate vitreous waste forms and glass-ceramics (also known as glass composite materials) are appropriate for determining the release mechanisms of LAW/LAWR mineral waste forms and how the durability data on LAW/LAWR mineral waste forms relate to the durability data for LAW/LAWR glasses. The text will discuss the LAW mineral waste form made by FBSR. The nanoscale mechanism by which the minerals form will be also be described in the text. The appropriate analyses to evaluate contaminant release mechanisms will be discussed, as will the FBSR test results to

  12. Co-gasification of biomass and plastics: pyrolysis kinetics studies, experiments on 100 kW dual fluidized bed pilot plant and development of thermodynamic equilibrium model and balances.

    Science.gov (United States)

    Narobe, M; Golob, J; Klinar, D; Francetič, V; Likozar, B

    2014-06-01

    Thermo-gravimetric analysis (TGA) of volatilization reaction kinetics for 50 wt.% mixtures of plastics (PE) and biomass (wood pellets) as well as for 100 wt.% plastics was conducted to predict decomposition times at 850°C and 900°C using iso-conversional model method. For mixtures, agreement with residence time of dual fluidized bed (DFB) reactor, treated as continuous stirred-tank reactor (CSTR), was obtained at large conversions. Mono-gasification of plastics and its co-gasification with biomass were performed in DFB pilot plant, using olivine as heterogeneous catalyst and heat transfer agent. It was found that co-gasification led to successful thermochemical conversion of plastics as opposed to mono-gasification. Unknown flow rates were determined applying nonlinear regression to energy and mass balances acknowledging combustion fuel, air, steam, feedstock, but also exiting char, tar, steam and other components in DFB gasification unit. Water-gas shift equilibrium and methanol synthesis requirements were incorporated into gasification model, based on measurements.

  13. Principles of a novel multistage circulating fluidized bed reactor for biomass gasification

    NARCIS (Netherlands)

    Kersten, Sascha R.A.; Prins, Wolter; Drift, van der Bram; Swaaij, van Wim P.M.

    2003-01-01

    In this paper a novel multistage circulating fluidized bed reactor has been introduced. The riser of this multistage circulating fluidized bed consists of several segments (seven in the base-case design) in series each built-up out of two opposite cones. Due to the specific shape, a fluidized bed ar

  14. Biomass gasification: the understanding of sulfur, tar, and char reaction in fluidized bed gasifiers

    NARCIS (Netherlands)

    Meng, X.

    2012-01-01

    As one of the currently available thermo-chemical conversion technologies, biomass gasification has received considerable interest since it increases options for combining with various power generation systems. The product gas or syngas produced from biomass gasification is environmental friendly

  15. Biomass-to-electricity: analysis and optimization of the complete pathway steam explosion--enzymatic hydrolysis--anaerobic digestion with ICE vs SOFC as biogas users.

    Science.gov (United States)

    Santarelli, M; Barra, S; Sagnelli, F; Zitella, P

    2012-11-01

    The paper deals with the energy analysis and optimization of a complete biomass-to-electricity energy pathway, starting from raw biomass towards the production of renewable electricity. The first step (biomass-to-biogas) is based on a real pilot plant located in Environment Park S.p.A. (Torino, Italy) with three main steps ((1) impregnation; (2) steam explosion; (3) enzymatic hydrolysis), completed by a two-step anaerobic fermentation. In the second step (biogas-to-electricity), the paper considers two technologies: internal combustion engines and a stack of solid oxide fuel cells. First, the complete pathway has been modeled and validated through experimental data. After, the model has been used for an analysis and optimization of the complete thermo-chemical and biological process, with the objective function of maximization of the energy balance at minimum consumption. The comparison between ICE and SOFC shows the better performance of the integrated plants based on SOFC.

  16. CO-FIRING COAL: FEEDLOT AND LITTER BIOMASS (CFB AND CLB) FUELS IN PULVERIZED FUEL AND FIXED BED BURNERS

    Energy Technology Data Exchange (ETDEWEB)

    Kalyan Annamalai; John Sweeten; Saqib Mukhtar; Ben Thein; Gengsheng Wei; Soyuz Priyadarsan; Senthil Arumugam; Kevin Heflin

    2003-08-28

    Intensive animal feeding operations create large amounts of animal waste that must be safely disposed of in order to avoid environmental degradation. Cattle feedlots and chicken houses are two examples. In feedlots, cattle are confined to small pens and fed a high calorie grain-diet diet in preparation for slaughter. In chicken houses, thousands of chickens are kept in close proximity. In both of these operations, millions of tons of manure are produced every year. The manure could be used as a fuel by mixing it with coal in a 90:10 blend and firing it in an existing coal suspension fired combustion systems. This technique is known as co-firing, and the high temperatures produced by the coal will allow the biomass to be completely combusted. Reburn is a process where a small percentage of fuel called reburn fuel is injected above the NO{sub x} producing, conventional coal fired burners in order to reduce NO{sub x}. The manure could also be used as reburn fuel for reducing NO{sub x} in coal fired plants. An alternate approach of using animal waste is to adopt the gasification process using a fixed bed gasifier and then use the gases for firing in gas turbine combustors. In this report, the cattle manure is referred to as feedlot biomass (FB) and chicken manure as litter biomass (LB). The report generates data on FB and LB fuel characteristics. Co-firing, reburn, and gasification tests of coal, FB, LB, coal: FB blends, and coal: LB blends and modeling on cofiring, reburn systems and economics of use of FB and LB have also been conducted. The biomass fuels are higher in ash, lower in heat content, higher in moisture, and higher in nitrogen and sulfur (which can cause air pollution) compared to coal. Small-scale cofiring experiments revealed that the biomass blends can be successfully fired, and NO{sub x} emissions will be similar to or lower than pollutant emissions when firing coal. Further experiments showed that biomass is twice or more effective than coal when

  17. Packed-bed column biosorption of chromium(VI) and nickel(II) onto Fenton modified Hydrilla verticillata dried biomass.

    Science.gov (United States)

    Mishra, Ashutosh; Tripathi, Brahma Dutt; Rai, Ashwani Kumar

    2016-10-01

    The present study represents the first attempt to investigate the biosorption potential of Fenton modified Hydrilla verticillata dried biomass (FMB) in removing chromium(VI) and nickel(II) ions from wastewater using up-flow packed-bed column reactor. Effects of different packed-bed column parameters such as bed height, flow rate, influent metal ion concentration and particle size were examined. The outcome of the column experiments illustrated that highest bed height (25cm); lowest flow rate (10mLmin(-1)), lowest influent metal concentration (5mgL(-1)) and smallest particle size range (0.25-0.50mm) are favourable for biosorption. The maximum biosorption capacity of FMB for chromium(VI) and nickel(II) removal were estimated to be 89.32 and 87.18mgg(-1) respectively. The breakthrough curves were analyzed using Bed Depth Service Time (BDST) and Thomas models. The experimental results obtained agree to both the models. Column regeneration experiments were also carried out using 0.1M HNO3. Results revealed good reusability of FMB during ten cycles of sorption and desorption. Performance of FMB-packed column in treating secondary effluent was also tested under identical experimental conditions. Results demonstrated significant reduction in chromium(VI) and nickel(II) ions concentration after the biosorption process.

  18. CO-FIRING COAL, FEEDLOT, AND LITTER BIOMASS (CFB AND LFB) FUELS IN PULVERIZED FUEL AND FIXED BED BURNERS

    Energy Technology Data Exchange (ETDEWEB)

    Kalyan Annamalai; John Sweeten; Saqib Mukhtar; Ben Thien; Gengsheng Wei; Soyuz Priyadarsan

    2002-01-15

    result as the levels of N are higher in the biomass fuel than in coal. Further experiments showed that biomass is twice or more effective than coal when used in a reburning process to reduce NO{sub x} emissions. Since crushing costs of biomass fuels may be prohibitive, stoker firing may be cost effective; in order simulate such a firing, future work will investigate the performance of a gasifier when fired with larger sized coal and biomass. It will be a fixed bed gasifier, and will evaluate blends, coal, and biomass. Computer simulations were performed using the PCGC-2 code supplied by BYU and modified by A&M with three mixture fractions for handling animal based biomass fuels in order to include an improved moisture model for handling wet fuels and phosphorus oxidation. Finally the results of the economic analysis show that considerable savings can be achieved with the use of biomass. In the case of higher ash and moisture biomass, the fuel cost savings will be reduced, due to increased transportation costs. A spreadsheet program was created to analyze the fuel savings for a variety of different moisture levels, ash levels, and power plant operating parameters.

  19. Fast Pyrolysis of Biomass in a Spout-fluidized Bed Reactor--Analysis of Composition and Combustion Characteristics of Liquid Product from Biomass

    Institute of Scientific and Technical Information of China (English)

    陈明强; 王君; 王新运; 张学才; 张素平; 任铮伟; 颜涌捷

    2006-01-01

    In order to gain insight into the fast pyrolysis mechanism of biomass and the relationship between bio-oil composition and pyrolysis reaction conditions, to assess the possibility for the raw bio-oil to be used as fuel, and to evaluate the concept of spout-fluidized bed reactor as the reactor for fast pyrolysis of biomass to prepare fuel oil, the composition and combustion characteristics of bio-oil prepared in a spout-fluidized bed reactor with a designed maximum capacity 5 kg/h of sawdust as feeding material, were investigated by GC-MS and thermogravimetry. 14 aromatic series chemicals were identified. The thermogravimetric analysis indicated that the bio-oil was liable to combustion, the combustion temperature increased with the heating rate, and only minute ash was generated when it burned. The kinetics of the combustion reaction was studied and the kinetic parameters were calculated by both Ozawa-Flynn-Wall and Popsecu methods. The results agree well with each other. The most probable combustion mechanism functions determined by Popescu method are f(α)=k(1-α)2(400~406 ℃), f(α)=1/2k(1-α)3 (406~416 ℃) and f( α)=2k(1-α)3/2 (416~430 ℃) respectively.

  20. Effect of Air Staging Ratios on the Burning Rate and Emissions in an Underfeed Fixed-Bed Biomass Combustor

    Directory of Open Access Journals (Sweden)

    Araceli Regueiro

    2016-11-01

    Full Text Available This experimental work studies a small-scale biomass combustor (5–12 kW with an underfed fixed bed using low air staging ratios (15%–30%. This document focuses on the influence of the operative parameters on the combustion process, so gaseous emissions and the distribution and concentration of particulate matter have also been recorded. The facility shows good stability and test repeatability. For the studied airflow ranges, the results show that increasing the total airflow rate does not increase the overall air excess ratio because the burning rate is proportionally enhanced (with some slight differences that depend on the air staging ratio. Consequently, the heterogeneous reactions at the bed remain in the so-called oxygen-limited region, and thus the entire bed operates under sub-stoichiometric conditions with regards of the char content of the biomass. In addition, tests using only primary air (no staging may increase the fuel consumption, but in a highly incomplete way, approaching a gasification regime. Some measured burning rates are almost 40% higher than previous results obtained in batch combustors due to the fixed position of the ignition front. The recorded concentration of particulate matter varies between 15 and 75 mg/Nm3, with a main characteristic diameter between 50 and 100 nm.

  1. Potential approaches to improve gasification of high water content biomass rich in cellulose in dual fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Dong, Li; Xu, Guangwen [State Key Laboratory of Multiphase Complex System, Institute of Process Engineering, Chinese Academy of Sciences, Beijing (China); Suda, Toshiyuki [Research Laboratory, IHI Corporation, Ltd., Yokohama (Japan); Murakami, Takahiro [National Institute of Advanced Science and Technology, Tsukuba (Japan)

    2010-08-15

    Biomass containing water of 30-65 wt.% and rich in cellulose, such as various grounds of drinking materials and the lees of spirit and vinegar, is not suitable for biological digestion, and the thermal conversion approach has to be applied to its conversion into bioenergy. The authors have recently worked on converting such biomass into middle heating-value gas via dual fluidized bed gasification (DFBG) integrated with various process intensification technologies. This article is devoted to highlighting those technical ways, including the choice of the superior technical deployment for a DFBG system, the impregnation of Ca onto fuel in fuel drying, the integration of gas cleaning with fuel gasification via two-stage DFBG (T-DFBG), and the decoupling of fuel drying/pyrolysis and char gasification via the decoupled DFBG (D-DFBG). The attained results demonstrated that the superior deployment of bed combination for the DFBG should be a bubbling/turbulent fluidized bed gasifier integrated with a pneumatic riser combustor. In terms of improving efficiency of fuel conversion into combustible gas and suppressing tar generation during gasification, the impregnation of Ca onto fuel exhibited distinctively high upgrading effect, while both the T-DFBG and D-DFBG were also demonstrated to be effective to a certain degree. (author)

  2. Development of fluidized bed combustion of biomass; Leijupolttoprosessin kehittaeminen vaikeille biopolttoaineille soveltuvaksi

    Energy Technology Data Exchange (ETDEWEB)

    Hiltunen, M.; Vaehaenen-Koivuluoma, T. [Foster Wheeler Energia Oy, Karhula (Finland)

    1997-10-01

    Some commercial BFB boilers burning biofuels, or biofuels and industrial wood wastes have suffered serious problems in bed material sintering. In worst cases the cumulation of reactive alkali compounds has caused total sintering of bed material even during a few days` operation. This presentation reports the results obtained from three separate cases, where sintering problems occurred. Boiler A burned biofuel with quartz sand and limestone addition. Boiler B burned softwood bark and industrial wood waste with sand addition. Boiler C burned softwood bark and sludge with sand addition. Due to the fuel used, bed sintering occurred in all boilers. Obviously, sintering was also influenced by some technical problems. Bed material samples have been analyzed with XRF and SEM-EDS techniques. According to these analyses, the main reason for sintering in boiler A is the cumulation of reactive potassium in bed material. In boiler B, the main reason is the fuel change from a mixture of softwood bark and industrial wood waste to pure industrial wood waste. The extra load of reactive sodium exceeded the critical concentration of alkali compounds in bed material. Also in boiler C, the fuel change from a mixture of softwood bark and sludge to pure softwood bark seems to be one of the reasons for bed sintering. After the fuel change the bed saturated with reactive potassium and the bed sintered. (orig.)

  3. Heterotrophic, nitrifying and denitrifying activity of biomass from fluidized bed reactor operated with aeration cycles

    Energy Technology Data Exchange (ETDEWEB)

    Martin Martin, A.; Damianovic, M.; Garcia-Encina, P. A.

    2009-07-01

    Biomass activity can be defined as the mass of substrate metabolised per unit of biomass and time. This parameter have a great importance to know the metabolic conditions of the microorganisms in a biological process, and can be use for an adequate operation and control of a wastewater treatment system. There are different methods to determine biomass activity, but the more useful are those based on the determination of the rate of substrate consumption or products generation. (Author)

  4. Co-firing coal and biomass in a fluidised bed boiler

    CSIR Research Space (South Africa)

    North, BC

    2005-11-01

    Full Text Available multi-national food company based in Estcourt, Kwa-Zulu Natal, South Africa. Two design requirements emerged from the clients needs: Additional plant steam and disposal of 12 t/h of coffee grounds sludge containing up to 87% water. The dual purpose...

  5. Combustion of gases released from peat or biomass in fluidized bed

    Energy Technology Data Exchange (ETDEWEB)

    Raiko, R. [Tampere Univ. of Technology (Finland). Energy and Process Engineering

    1996-12-01

    Temperature and gas concentration experiments have been conducted to determine at what temperature carbon monoxide, methane and propane begin to react within the particulate phase of a bubbling fluidized bed. The fluidized bed reactor used in these experiments was a stainless-steel tube with an internal diameter of 50 mm surrounded by an electric heater. Two different natural quartz sands were used (d{sub p} =0.35 mm and 0.6 mm). The bed height used varied between 100 and 260 mm (in unfluidized state). A porous plate distributor, made of kaowool, was used to avoid jets appearing at the distributor. The bed was operated at incipient fluidization (u = 5.9-9 cm/s). The bed temperatures used ranged from 600 deg C to 850 deg C. It was found that carbon monoxide, methane and propane react inside a fluidized bed, but often other conditions than temperature have a considerable effect on the rate of the reaction. The critical temperature was found to be 650 deg C for propane and carbon monoxide and 700 deg C for methane. With under-stoichiometric mixture of carbon monoxide and air the heat release can be over 2.5 MW/m{sup 3} when bed temperature is 650 deg C. According to these experiments it is obvious that the reaction mechanism for carbon monoxide oxidation inside a fluidized bed differs greatly from that of gas phase only. The results of our more than 1300 test runs show clearly the varying effects of the different bed materials. Even with the same bed material totally different results can be obtained. In order to elucidate the possible changes of particle surface, microscopic and porosimetric studies was conducted with both fresh bed particles and used bed particles. Also the effect of commonly used ingredients, like limestone and dolomite, was tested. A global model for carbon monoxide oxidation inside a fluidized bed was introduced. The model was tested against measured data from the laboratory-scale fluidized bed test rig. (Abstract Truncated)

  6. Evaluation of aboveground and belowground biomass recovery in physically disturbed seagrass beds.

    Science.gov (United States)

    Di Carlo, Giuseppe; Kenworthy, W Judson

    2008-11-01

    Several studies addressed aboveground biomass recovery in tropical and subtropical seagrass systems following physical disturbance. However, there are few studies documenting belowground biomass recovery despite the important functional and ecological role of roots and rhizomes for seagrass ecosystems. In this study, we compared the recovery of biomass (g dry weight m(-2)) as well as the biomass recovery rates in ten severely disturbed multi-species seagrass meadows, after the sediments were excavated and the seagrasses removed. Three sites were located in the tropics (Puerto Rico) and seven in the subtropics (Florida Keys), and all were originally dominated by Thalassia testudinum. Total aboveground biomass reached reference values at four out of ten sites studied, two in the Florida Keys and two in Puerto Rico. Total belowground biomass was lower at the disturbed locations compared to the references at all sites, apart from two sites in the Florida Keys where the compensatory effect of opportunistic species (Syringodium filiforme and Halodule wrightii) was observed. The results revealed large variation among sites in aboveground and belowground biomass for all species, with higher aboveground recovery than belowground for T. testudinum. Recovery rates for T. testudinum were highly variable across sites, but a general trend of faster aboveground than belowground recovery was observed. Equal rates between aboveground and belowground biomass were found for opportunistic species at several sites in the Florida Keys. These results indicate the importance of belowground biomass when assessing seagrass recovery and suggest that the appropriate metric to assess seagrass recovery should address belowground biomass as well as aboveground biomass in order to evaluate the full recovery of ecological services and functions performed by seagrasses. We point out regional differences in species composition and species shifts following severe disturbance events and discuss

  7. Nitric oxide reduction over biomass and coal chars under fluidized bed combustion conditions: the role of thermal annealing

    Energy Technology Data Exchange (ETDEWEB)

    Piero Salatino; Anna Di Somma; Roberto Solimene; Riccardo Chirone [Universita degli Studi di Napoli Federico II, Napoli (Italy). Dipartimento di Ingegneria Chimica

    2008-07-01

    The de-NOx potential of biomass-and waste-derived fuels candidate for cofiring with coal is assessed. The experimental procedure is based on operation of a bench scale fluidized bed reactor where NO-doped nitrogen is contacted with batches of the fuel. A second type of experiment has been purposely designed to assess the extent of thermodeactivation of biogenous fuels, i.e. the loss of reactivity toward the NOx-char reaction as char is annealed for pre-set times at temperatures typical of fluidized bed combustion. A simple phenomenological model is developed to shed light on the basic features of the interaction between heterogeneous char-NOx reaction and thermal annealing of the char. Results are discussed in the light of the potential exploitation of synergistic effects on NOx emission associated with cofiring with coal. 21 refs., 8 figs., 1 tab.

  8. Biomass gasification: the understanding of sulfur, tar, and char reaction in fluidized bed gasifiers

    NARCIS (Netherlands)

    Meng, X.

    2012-01-01

    As one of the currently available thermo-chemical conversion technologies, biomass gasification has received considerable interest since it increases options for combining with various power generation systems. The product gas or syngas produced from biomass gasification is environmental friendly al

  9. Chemical characteristics and enzymatic saccharification of lignocellulosic biomass treated using high-temperature saturated steam: comparison of softwood and hardwood.

    Science.gov (United States)

    Asada, Chikako; Sasaki, Chizuru; Hirano, Takeshi; Nakamura, Yoshitoshi

    2015-04-01

    This study investigated the effect of high-temperature saturated steam treatments on the chemical characteristics and enzymatic saccharification of softwood and hardwood. The weight loss and chemical modification of cedar and beech wood pieces treated at 25, 35, and 45 atm for 5 min were determined. Fourier transform infrared and X-ray diffraction analyses indicated that solubilization and removal of hemicellulose and lignin occurred by the steam treatment. The milling treatment of steam-treated wood enhanced its enzymatic saccharification. Maximum enzymatic saccharification (i.e., 94% saccharification rate of cellulose) was obtained using steam-treated beech at 35 atm for 5 min followed by milling treatment for 1 min. However, the necessity of the milling treatment for efficient enzymatic saccharification is dependent on the wood species.

  10. Comparative study on pyrolysis of lignocellulosic and algal biomass using a thermogravimetric and a fixed-bed reactor.

    Science.gov (United States)

    Yuan, Ting; Tahmasebi, Arash; Yu, Jianglong

    2015-01-01

    Pyrolysis characteristics of four algal and lignocellulosic biomass samples were studied by using a thermogravimetric analyzer (TGA) and a fixed-bed reactor. The effects of pyrolysis temperature and biomass type on the yield and composition of pyrolysis products were investigated. The average activation energy for pyrolysis of biomass samples by FWO and KAS methods in this study were in the range of 211.09-291.19kJ/mol. CO2 was the main gas component in the early stage of pyrolysis, whereas H2 and CH4 concentrations increased with increasing pyrolysis temperature. Bio-oil from Chlorellavulgaris showed higher content of nitrogen containing compounds compared to lignocellulosic biomass. The concentration of aromatic organic compounds such as phenol and its derivatives were increased with increasing pyrolysis temperature up to 700°C. FTIR analysis results showed that with increasing pyrolysis temperature, the concentration of OH, CH, CO, OCH3, and CO functional groups in char decreased sharply. Copyright © 2014 Elsevier Ltd. All rights reserved.

  11. Bed agglomeration in biomass fueled CFB-boilers; Sintring av baeddmaterial vid biobraensleeldning i CFB

    Energy Technology Data Exchange (ETDEWEB)

    Zintl, F. [TPS Termiska Processer AB, Nykoeping (Sweden)

    1997-02-01

    In fluidized-bed boilers fired with solid fuels operational problems caused by spontaneous defluidization are sometimes observed. This bed agglomeration can be caused by sintering phenomena where fuel components and/or bed material may be involved. In serious cases the problems can lead to expensive operation breaks. The objective in this project was to show whether this type of operational problems can be minimized by choice of other than conventional bed materials. The study was carried out as model experiments in a larger laboratory scale. In a fluidized bed fired with propane a number of both well known and more unusual bed materials were tried out. The choice of bed materials included some common sands (silver and quartz sand) and, as possible alternatives, olivine sand, zirconium sand, calcined dolomite and the synthetic materials sintered magnesite (MgO) and mullite (alumina silicate). The model experiments were started at about 700 deg C and the temperature then raised until an irreversible bed agglomeration was observed, or to a maximum of 1100 deg C. The most promising results were obtained with calcined dolomite, being an active bed material. With this material no irreversible agglomerations were observed at all. The expensive synthetic materials sintered magnesite and mullite and the zirconium sand turned out as the next best. Olivine sand, on the other hand, showed a clear sensitivity to physical agglomeration and some sensitivity also towards sintering. The common sand types based on silicon oxide clearly showed the worst results. 12 refs, 5 figs, 1 tab 12 refs, 5 figs, 1 tab

  12. Material problems related to large scale firing of biomass. Steam oxidation of TP 347H FG and X20

    Energy Technology Data Exchange (ETDEWEB)

    Noergaard Hansson, A.

    2009-07-01

    TP 347 H and X20 is often used as construction material in biomass-fired boilers. The corrosion rate of the alloys is affected by the metal temperature. In this project, the oxidation behaviour of TP 347H FG and X20 is studied by field-testing, laboratory exposures, and thermodynamic/kinetic modelling. The long term oxidation behaviour of TP 347H FG at ultra supercritical steam conditions was assessed by exposing the steel in 4 test superheater loops in a coal-fired power plant. The steel was exposed for 7720, 22985, 29588, and 57554 h at metal temperatures between 499 and 650 deg. C. In the laboratory furnace, the oxidation behaviour of TP 347H FG, TP 347H CG, and X20 was studied in water vapour containing environments (8 or 46%) in the temperature range 500-700 deg. C. Air, Ar and Ar+7% H{sub 2} were used as carrier gas. The microstructure of the oxide layer and the subjacent alloy was investigated with X-ray diffraction (XRD), reflective light microscopy (RLM), scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), and transmission electron microscopy (TEM) equipped with electron diffraction (ED) and EDS. Double-layered oxides developed during steam oxidation of TP 347H FG both during field-testing and during laboratory exposures. TEM investigation suggested that the interior of the alloy grain was oxidised internally, forming particles of metallic Ni/Fe and Fe-Cr spinel. A FeCr{sub 2}O{sub 4} layer developed along the former alloy grain boundaries. Cr{sub 2}O{sub 3} developed in between this layer and the alloy during field-testing, and its formation was promoted by higher temperature. The morphology of the inner layer for the samples oxidised below and above approx. 585 deg. C looked very different in SEM (field-testing). It is suggested that more Cr is incorporated into the oxide layer at higher temperature, gradually transforming the morphology of the inner oxide layer. The alloy beneath the oxide layer was depleted in Cr

  13. Material problems related to large scale firing of biomass. Steam oxidation of TP 347H FG and X20

    Energy Technology Data Exchange (ETDEWEB)

    Noergaard Hansson, A.

    2009-07-01

    TP 347 H and X20 is often used as construction material in biomass-fired boilers. The corrosion rate of the alloys is affected by the metal temperature. In this project, the oxidation behaviour of TP 347H FG and X20 is studied by field-testing, laboratory exposures, and thermodynamic/kinetic modelling. The long term oxidation behaviour of TP 347H FG at ultra supercritical steam conditions was assessed by exposing the steel in 4 test superheater loops in a coal-fired power plant. The steel was exposed for 7720, 22985, 29588, and 57554 h at metal temperatures between 499 and 650 deg. C. In the laboratory furnace, the oxidation behaviour of TP 347H FG, TP 347H CG, and X20 was studied in water vapour containing environments (8 or 46%) in the temperature range 500-700 deg. C. Air, Ar and Ar+7% H{sub 2} were used as carrier gas. The microstructure of the oxide layer and the subjacent alloy was investigated with X-ray diffraction (XRD), reflective light microscopy (RLM), scanning electron microscopy (SEM) equipped with energy dispersive spectroscopy (EDS), and transmission electron microscopy (TEM) equipped with electron diffraction (ED) and EDS. Double-layered oxides developed during steam oxidation of TP 347H FG both during field-testing and during laboratory exposures. TEM investigation suggested that the interior of the alloy grain was oxidised internally, forming particles of metallic Ni/Fe and Fe-Cr spinel. A FeCr{sub 2}O{sub 4} layer developed along the former alloy grain boundaries. Cr{sub 2}O{sub 3} developed in between this layer and the alloy during field-testing, and its formation was promoted by higher temperature. The morphology of the inner layer for the samples oxidised below and above approx. 585 deg. C looked very different in SEM (field-testing). It is suggested that more Cr is incorporated into the oxide layer at higher temperature, gradually transforming the morphology of the inner oxide layer. The alloy beneath the oxide layer was depleted in Cr

  14. The impact of steam and current density on carbon formation from biomass gasification tar on Ni/YSZ, and Ni/CGO solid oxide fuel cell anodes

    Science.gov (United States)

    Mermelstein, Joshua; Millan, Marcos; Brandon, Nigel

    The combination of solid oxide fuel cells (SOFCs) and biomass gasification has the potential to become an attractive technology for the production of clean renewable energy. However the impact of tars, formed during biomass gasification, on the performance and durability of SOFC anodes has not been well established experimentally. This paper reports an experimental study on the mitigation of carbon formation arising from the exposure of the commonly used Ni/YSZ (yttria stabilized zirconia) and Ni/CGO (gadolinium-doped ceria) SOFC anodes to biomass gasification tars. Carbon formation and cell degradation was reduced through means of steam reforming of the tar over the nickel anode, and partial oxidation of benzene model tar via the transport of oxygen ions to the anode while operating the fuel cell under load. Thermodynamic calculations suggest that a threshold current density of 365 mA cm -2 was required to suppress carbon formation in dry conditions, which was consistent with the results of experiments conducted in this study. The importance of both anode microstructure and composition towards carbon deposition was seen in the comparison of Ni/YSZ and Ni/CGO anodes exposed to the biomass gasification tar. Under steam concentrations greater than the thermodynamic threshold for carbon deposition, Ni/YSZ anodes still exhibited cell degradation, as shown by increased polarization resistances, and carbon formation was seen using SEM imaging. Ni/CGO anodes were found to be more resilient to carbon formation than Ni/YSZ anodes, and displayed increased performance after each subsequent exposure to tar, likely due to continued reforming of condensed tar on the anode.

  15. Co-gasification of biomass and coal in a pressurised fluidised bed gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Andries, L.; Hein, K.R.G. [Lab. for Thermal Power Engineering, Dept. of Mechanical Engineering and Marine Technology, Delft Univ. of Technology (Netherlands)

    1996-12-31

    The Laboratory for Thermal Power Engineering of the Delft University of Technology is participating in an EU funded, international, R + D project which is designed to aid European industry in addressing issues regarding co-utilisation of biomass and/or waste in advanced coal conversion processes. The project comprises three main programmes, each of which includes a number of smaller subprogrammes. The three main programmes are: Coal-biomass systems component development and design; Coal-biomass environmental studies; Techno-economic assessment studies. (orig)

  16. Biomass gasification: the understanding of sulfur, tar, and char reaction in fluidized bed gasifiers

    OpenAIRE

    Meng, X.(Institute of High Energy Physics, Beijing, China)

    2012-01-01

    As one of the currently available thermo-chemical conversion technologies, biomass gasification has received considerable interest since it increases options for combining with various power generation systems. The product gas or syngas produced from biomass gasification is environmental friendly alternatives to conventional petrochemical fuels for the production of electricity, hydrogen, synthetic transportation biofuels and other chemicals. The product gas normally contains the major compon...

  17. 生物质焦的水蒸气汽化动力学研究%Steam gasification kinetics of biomass char

    Institute of Scientific and Technical Information of China (English)

    许桂英; 孙国刚; 程辉; 汪洋

    2011-01-01

    生物质汽化包括生物质的热解及随后的生物质焦的水蒸气汽化过程.为了给生物质汽化反应器的设计提供基础数据,利用热天平试验装置对1 273 K制备的生物质焦行了水蒸气汽化反应性试验,研究了汽化温度对汽化反应性、平均比汽化速率、反应速率等的影响.并且利用均相模型和缩芯模型拟合试验数据求得了相应的动力学参数.得出结论:随着温度的增加,焦炭汽化反应性增加,平均比汽化速率增加.由均相模型所算得活化能为181.24 kJ/mol,指前因子为5.19x 105 min-1,缩芯模型所算得活化能为192.87 kJ/mol,指前因子为1.60x 106 min-1.在转化率为10%~75%范围内,均相模型和缩芯模型均可以很好的描述生物质焦的水蒸气汽化行为,但是缩芯模型比均相模型的拟合效果要好. .%Biomass gasification includes biomass pyrolysis and steam gasification of biomass chars subsequently. In order to provide basic data for the design of biomass gasification reactor, thermal balance was used to finish steam gasification of biomass char, which was produced at 1273K. Effects of the gasification temperature on the gasification reactivity, the average gasification rate, and the reaction rate were investigated. And the homogeneous model and shrinking core model were employed to obtain the corresponding kinetic parameters. With the increasing temperature, biomass steam gasification reactivity and the average rate increased. The activity energy was 181.24 kJ/mol, the pre-exponential factor was 5.19×105 min-1 with homogeneous model. The activity energy was 192.87 kJ/mol, pre-exponential factor was 1.60×10-6 min-1 with shrinking core model. Both shrinking core model and homogeneous model can describe the process of biomass char steam gasification well, however, shrinking core model fit the experimental data better than homogeneous model.

  18. Characteristics of ash and particle emissions during bubbling fluidised bed combustion of three types of residual forest biomass.

    Science.gov (United States)

    Ribeiro, João Peres; Vicente, Estela Domingos; Alves, Célia; Querol, Xavier; Amato, Fulvio; Tarelho, Luís A C

    2017-04-01

    Combustion of residual forest biomass (RFB) derived from eucalypt (Eucalyptus globulus), pine (Pinus pinaster) and golden wattle (Acacia longifolia) was evaluated in a pilot-scale bubbling fluidised bed reactor (BFBR). During the combustion experiments, monitoring of temperature, pressure and exhaust gas composition has been made. Ash samples were collected at several locations along the furnace and flue gas treatment devices (cyclone and bag filter) after each combustion experiment and were analysed for their unburnt carbon content and chemical composition. Total suspended particles (TSP) in the combustion flue gas were evaluated at the inlet and outlet of cyclone and baghouse filter and further analysed for organic and elemental carbon, carbonates and 57 chemical elements. High particulate matter collection efficiencies in the range of 94-99% were observed for the baghouse, while removal rates of only 1.4-17% were registered for the cyclone. Due to the sand bed, Si was the major element in bottom ashes. Fly ashes, in particular those from eucalypt combustion, were especially rich in CaO, followed by relevant amounts of SiO2, MgO and K2O. Ash characteristics varied among experiments, showing that their inorganic composition strongly depends on both the biomass composition and combustion conditions. Inorganic constituents accounted for TSP mass fractions up to 40 wt%. Elemental carbon, organic matter and carbonates contributed to TSP mass fractions in the ranges 0.58-44%, 0.79-78% and 0.01-1.7%, respectively.

  19. Materials for higher steam temperatures (up to 600 deg C) in biomass and waste fired plant. A review of present knowledge; Material foer hoegre aangtemperaturer (upp till 600 grader C) i bio- och avfallseldade anlaeggningar

    Energy Technology Data Exchange (ETDEWEB)

    Staalenheim, Annika; Henderson, Pamela

    2011-02-15

    A goal for the Swedish power industry is to build a demonstration biomass-fired plant with 600 deg C steam data in 2015. Vaermeforsk also has a goal to identify materials that can be used in such a plant. This project involves a survey of present knowledge and published articles concerning materials that are suitable for use in biomass and wastefired plants with steam data up to 600 deg C. The information has been gathered from plants presently in operation, and from field tests previously performed with probes. Plants firing only household waste are excluded. The components considered are waterwalls/furnace walls (affected because of higher steam pressures) and superheaters. Fireside corrosion and steam-side oxidation are dealt with. Candidate materials (or coatings) are suggested and areas for further research have been identified. The purpose of this project is to give state-of-the-art information on what materials could be used in biomass and waste-fired plant to reach a maximum steam temperature of 600 deg C. This report is aimed at suppliers of boilers and materials, energy utility companies and others involved in building new plant with higher steam data. In accordance with the goals of this project: - Materials suitable for use at higher steam temperatures (up to 600 deg C steam) in wood-based biomass and waste-fired plant have been identified. Austenitic stainless steels HR3C, TP 347 HFG and AC66 all have adequate strength, steam-side oxidation and fireside corrosion resistance for use as superheaters. AC66 and HR3C have better steam-side oxidation resistance than TP 347 HFG , but TP 347 HFG has better fireside corrosion resistance. It is recommended that TP 347 HFG be shot-peened on the inside to improve the oxidation resistance if in service with steam temperatures above 580 deg C. - Furnace walls coated with Ni-based alloys or a mixture of Ni- alloy and ceramic show good corrosion resistance at lower temperatures and should be evaluated at higher

  20. Performance Analysis of Solar Assisted Fluidized Bed Dryer Integrated Biomass Furnace with and without Heat Pump for Drying of Paddy

    Directory of Open Access Journals (Sweden)

    M. Yahya

    2016-01-01

    Full Text Available The performances of a solar assisted fluidized bed dryer integrated biomass furnace (SA-FBDIBF and a solar assisted heat pump fluidized bed dryer integrated biomass furnace (SAHP-FBDIBF for drying of paddy have been evaluated, and also drying kinetics of paddy were determined. The SA-FBDIBF and the SAHP-FBDIBF were used to dry paddy from 11 kg with moisture content of 32.85% db to moisture content of 16.29% db (14% wb under an air mass flow rate of 0.1037 kg/s within 29.73 minutes and 22.95 minutes, with average temperatures and relative humidities of 80.3°C and 80.9°C and 12.28% and 8.14%, respectively. The average drying rate, specific energy consumption, and specific moisture extraction rate were 0.043 kg/minute and 0.050 kg/minute, 5.454 kWh/kg and 4.763 kWh/kg, and 0.204 kg/kWh and 0.241 kg/kWh for SA-FBDIBF and SAHP-FBDIBF, respectively. In SA-FBDIBF and SAHP-FBDIBF, the dryer thermal efficiencies were average values of 12.28% and 15.44%; in addition, the pickup efficiencies were 33.55% and 43.84% on average, whereas the average solar and biomass fractions were 10.9% and 10.6% and 36.6% and 30.4% for SA-FBDIBF and SAHP-FBDIBF, respectively. The drying of paddy occurred in the falling rate period. The experimental dimensionless moisture content data were fitted to three mathematical models. Page’s model was found best to describe the drying behaviour of paddy.

  1. Biomass fast pyrolysis in a fluidized bed reactor under N2, CO2, CO, CH4 and H2 atmospheres.

    Science.gov (United States)

    Zhang, Huiyan; Xiao, Rui; Wang, Denghui; He, Guangying; Shao, Shanshan; Zhang, Jubing; Zhong, Zhaoping

    2011-03-01

    Biomass fast pyrolysis is one of the most promising technologies for biomass utilization. In order to increase its economic potential, pyrolysis gas is usually recycled to serve as carrier gas. In this study, biomass fast pyrolysis was carried out in a fluidized bed reactor using various main pyrolysis gas components, namely N(2), CO(2), CO, CH(4) and H(2), as carrier gases. The atmosphere effects on product yields and oil fraction compositions were investigated. Results show that CO atmosphere gave the lowest liquid yield (49.6%) compared to highest 58.7% obtained with CH(4). CO and H(2) atmospheres converted more oxygen into CO(2) and H(2)O, respectively. GC/MS analysis of the liquid products shows that CO and CO(2) atmospheres produced less methoxy-containing compounds and more monofunctional phenols. The higher heating value of the obtained bio-oil under N(2) atmosphere is only 17.8 MJ/kg, while that under CO and H(2) atmospheres increased to 23.7 and 24.4 MJ/kg, respectively.

  2. Evaluation of a solar-biomass-rock bed storage drying system, and its application for chilli drying

    Energy Technology Data Exchange (ETDEWEB)

    Augustus Leon, M.; Kumar, S. [Energy Field of Study, Asian Inst. of Tech. Klong Luang, Pathumthani (Thailand)

    2008-07-01

    A renewable energy-based air heating system that does not require a conventional auxiliary heater, but can still meet a daily load fraction exceeding 90% and supply hot air at a steady temperature and flow rate continuously for 24 hours a day, has been developed. It combines an unglazed transpired solar collector (UTC), rock bed, and a biomass gasifier stove with heat exchanger. The system utilises part of the rock bed to supply supplementary heat. The UTC supplies the required hot air during the day (to meet the load), and the stove-heat exchanger unit supplies hot air to the rock bed (to charge it), also during the daytime. The rock bed stores the thermal energy during the daytime, and supplies heat during off-sunshine hours - both during day and night. The system was evaluated by drying 22 kg of red chilli, using hot air at 60 C and 90 m{sup 3}/h, from an initial moisture content of 76.7% (w.b) to 8.4% over 32.5 hours of continuous drying. The dryer contributed to a reduction of 66% in drying time compared to open sun drying. The temperature of hot air supplied was stable at 60{+-}3 C for over 24 hours during the entire drying duration. Providing a load fraction of 91.6% during the 24-hour operation, the air heating system can successfully dry red chilli in a continuous drying operation, at required air temperature and flow rate, which can be maintained fairly constant. (orig.)

  3. Fast Pyrolysis of Biomass in a Fluidized Bed Reactor: In Situ Filtering of the Vapors

    NARCIS (Netherlands)

    Hoekstra, Elly; Hogendoorn, Kees J.A.; Wang, Xiaoquan; Westerhof, Roel J.M.; Kersten, Sascha R.A.; Swaaij, van Wim P.M.; Groeneveld, Michiel J.

    2009-01-01

    A system to remove in situ char/ash from hot pyrolysis vapors has been developed and tested at the University of Twente. The system consists of a continuous fluidized bed reactor (0.7 kg/h) with immersed filters (wire mesh, pore size 5 μm) for extracting pyrolysis vapors. Integration of the filter s

  4. Effect of temperature in fluidized bed fast pyrolysis of biomass: oil quality assessment in test units

    NARCIS (Netherlands)

    Westerhof, Roel Johannes Maria; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria; Kersten, Sascha R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  5. Effect of Temperature in Fluidized Bed Fast Pyrolysis of Biomass: Oil Quality Assessment in Test Units

    NARCIS (Netherlands)

    Westerhof, R.J.M.; Brilman, D.W.F.; Swaaij, van W.P.M.; Kersten, S.R.A.

    2010-01-01

    Pine wood was pyrolyzed in a 1 kg/h fluidized bed fast pyrolysis reactor that allows a residence time of pine wood particles up to 25 min. The reactor temperature was varied between 330 and 580 °C to study the effect on product yields and oil composition. Apart from the physical−chemical analysis, a

  6. Biomass fast pyrolysis in fluidized bed : product cleaning by in-situ filtration

    NARCIS (Netherlands)

    Wang, Xiaoquan

    2006-01-01

    This thesis is dedicated to the subject of fast pyrolysis in a fluid bed reactor. A large part of the work is related to reactor design aspects of fast pyrolysis, a subject that has not been considered sufficiently. Past research efforts were focussed mainly on the kinetics of wood pyrolysis and the

  7. Comparative Kinetic Studies and Performance Evaluation of Biofilm and Biomass Characteristics of Pseudomonas fluorescens in Degrading Synthetic Phenolic Effluent in Inverse Fluidized Bed Biofilm Reactor.

    Science.gov (United States)

    Begum, S Sabarunisha; Radha, K V

    2016-05-01

    The bioremediation potential of Pseudomonas fluorescens was studied in an Inverse Fluidized Bed Biofilm Reactor under batch recirculation conditions using synthetic phenolic effluent of various concentrations (400, 600, 800, 1000 and 1200 mg/l). The performance of the reactor was investigated and the characteristics of biomass and biofilm were determined by evaluating biofilm dry density and thickness, bioparticle density, suspended and attached biomass concentration, chemical oxygen demand and phenol removal efficiency. Biodegradation kinetics had been studied for suspended biomass culture and biofilm systems with respect to its specific growth and substrate consumption rates. Suspended biomass followed substrate inhibition kinetics and the experimental data fitted well with the Haldane model. The degradation kinetic behavior of biofilm revealed that a well adapted biofilm system with effective control of biofilm thickness in an inverse fluidized bed biofilm reactor overcomes substrate inhibition effects by tolerating higher phenol concentration and fitted well to the Monod model.

  8. Gasification techniques and fluidized-bed gasification of biomass - ways of optimising combustion and energy utilisation. Vergasungstechniken und Wirbelschichtvergasung von Biomasse - Wege zur Optimierung der Verbrennung und der Energienutzung

    Energy Technology Data Exchange (ETDEWEB)

    Brunner, W. (Wamsler Umwelttechnik, Muenchen (Germany))

    1994-01-01

    To date, electricity can only be generated from biomass via steam production. There are no gasification techniques available for generating electricity from biomass at an industrial scale. The paper describes the current stage of development and two possible applications of a gasification technique whose attractivity lies not only in direct electricity production and utilisation of residual heat (block-type thermal power station). The gasification is also a way of compensating the drawbacks of solid fuel combustion compared with gas combustion. (orig./EF)

  9. Nitrogen compounds in pressurised fluidised bed gasification of biomass and fossil fuels

    NARCIS (Netherlands)

    De Jong, W.

    2005-01-01

    Fossil fuels still dominate the energy supply in modern societies. The resources, however, are depleting. Therefore, other energy sources are to be exploited further within this century. Biomass is one of the practically CO2 neutral, renewable contributors to the future energy production. Nowadays m

  10. 串行流化床生物质气化合成二甲醚的模拟%Simulation of DME Synthesis from Biomass Gasification in Interconnected Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    江宏玲; 肖军; 沈来宏

    2012-01-01

    Taking the rice straw as an object of study,a simulation model for synthesis of dimethyl ether(DME) from biomass gasification in interconnected fluidized beds was established using Aspen Plus software,so as to analyze how following factors influence the synthesis process,such as the gasification temperature,steam/biomass(mS/mB) mass ratio,synthesis temperature and pressure,absorption tower operating pressure and the absorbent/DME(nA/nD) flow ratio,ect.Results show that for the purpose of direct DME synthesis from biomass gasification in interconnected fluidized beds using steam gasification technology,it is suggested that relevant parameters be set as follows: gasification temperature at 750 ℃,mS/mB=0.3,and DME systhesis temperature and pressure respectively at 260 ℃ and 4 MPa;if water is taken as the absorbent,the absorption tower operating pressure is proposed to be within 3-4 MPa with an nA/nD ratio of 0.5.Under above optimal conditions,the DME yield may reach 6.1 mol per kg biomass.%以稻秸秆为研究对象,利用Aspen Plus软件建立了串行流化床生物质气化制取合成气合成二甲醚(DME)的模型,研究了不同气化温度、水蒸气与生物质的质量比(mS/mB)、DME合成温度、合成压力、吸收塔操作压力及吸收剂与DME的配比(nA/nD)对合成工艺的影响.结果表明:对于采用串行流化床生物质水蒸气气化技术制取DME的一步法合成系统,建议气化温度取750℃左右,mS/mB取0.3,DME合成温度取260℃,合成压力取4MPa,用水作吸收剂,吸收塔的操作压力控制在3~4MPa,nA/nD取0.5;在此工况下,1kg生物质(干燥基)所能产生的二甲醚物质的量约为6.1mol.

  11. Gas mixing in a pilot scale (500 KW{sub th}) air blown circulating fluidised bed biomass gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Kersten, S.R.A.; Moonen, R.H.W.; Oosting, T.P. [ECN Biomass, Petten (Netherlands); Prins, W.; Van Swaaij, W.P.M. [Faculty of Chemical Engineering, University of Twente, Enschede (Netherlands)

    2000-07-01

    To study the gas mixing capacity of circulating fluidised bed (CFB) biomass gasifiers, radial and axial gas concentration profiles have been measured and interpreted in both a hot pilot scale biomass gasifier (100 kg/hr fuel) and a cold-flow set-up. The presented data of the pilot scale gasifier are unique and provide new insight in the radial gas mixing capacity of circulating fluidised bed gasifiers. Gas mixing is an important process because the effectiveness of a CFB biomass gasifier, regarding conversion of carbon and tars in the product gas, depends among other things on the degree of reactant mixing. At five different axial positions, in the pilot plant, especially developed probes are installed to withdraw gases from the interior of the reactor. They can be moved freely over the reactor diameter, so full radial profiles can be obtained at each axial position. In the cold-flow set-up similar probes are used to determine radial dispersion coefficients as a function of process variables such as solids flux, gas velocity and additional internals. Considerable radial gas phase concentration gradients have been observed in the pilot plant gasifier, with a difference between wall and centre concentrations up to a factor 3. It must be concluded that the radial gas mixing is far from ideal. On basis of these pilot plant data and a suitable reactor model it can be concluded that the radial Peclet number of the dilute region is in the order of 1000. Such a value excludes the radial mixing of gases almost entirely. Simulations indicate that the occurrence of a parabolic gas velocity profile (also observed in earlier hydrodynamic studies) and a possibly non-uniform biomass distribution, are major causes for steep gradients in the radial gas concentration profiles. From the experiments in the cold-flow set-up it can be concluded that in the dilute region of the riser the radial mixing intensity decreases due to presence of solids. This can be ascribed to a reducing

  12. Bio-oil production via fast pyrolysis of biomass residues from cassava plants in a fluidised-bed reactor.

    Science.gov (United States)

    Pattiya, Adisak

    2011-01-01

    Biomass residues from cassava plants, namely cassava stalk and cassava rhizome, were pyrolysed in a fluidised-bed reactor for production of bio-oil. The aims of this work were to investigate the yields and properties of pyrolysis products produced from both feedstocks as well as to identify the optimum pyrolysis temperature for obtaining the highest organic bio-oil yields. Results showed that the maximum yields of the liquid bio-oils derived from the stalk and rhizome were 62 wt.% and 65 wt.% on dry basis, respectively. The pyrolysis temperatures that gave highest bio-oil yields for both feedstocks were in the range of 475-510 °C. According to the analysis of the bio-oils properties, the bio-oil derived from cassava rhizome showed better quality than that derived from cassava stalk as the former had lower oxygen content, higher heating value and better storage stability.

  13. Development of a bi-equilibrium model for biomass gasification in a downdraft bed reactor.

    Science.gov (United States)

    Biagini, Enrico; Barontini, Federica; Tognotti, Leonardo

    2016-02-01

    This work proposes a simple and accurate tool for predicting the main parameters of biomass gasification (syngas composition, heating value, flow rate), suitable for process study and system analysis. A multizonal model based on non-stoichiometric equilibrium models and a repartition factor, simulating the bypass of pyrolysis products through the oxidant zone, was developed. The results of tests with different feedstocks (corn cobs, wood pellets, rice husks and vine pruning) in a demonstrative downdraft gasifier (350kW) were used for validation. The average discrepancy between model and experimental results was up to 8 times less than the one with the simple equilibrium model. The repartition factor was successfully related to the operating conditions and characteristics of the biomass to simulate different conditions of the gasifier (variation in potentiality, densification and mixing of feedstock) and analyze the model sensitivity.

  14. Controlled biomass formation and kinetics of toluene degradation in a bioscrubber and in a reactor with a periodically moved trickle-bed.

    Science.gov (United States)

    Wübker, S M; Laurenzis, A; Werner, U; Friedrich, C

    1997-08-20

    The kinetics of degradation of toluene from a model waste gas and of biomass formation were examined in a bioscrubber operated under different nutrient limitations with a mixed culture. The applicability of the kinetics of continuous cultivation of the mixed culture was examined for a special trickle-bed reactor with a periodically moved filter bed. The efficiency of toluene elimination of the bioscrubber was 50 to 57% and depended on the toluene mass transfer as evident from a constant productivity of 0.026 g dry cell weight/L . h over the dilution rate. Under potassium limitation the biomass productivity was reduced by 60% to 0.011 g dry cell weight/L . h at a dilution rate of 0.013/h. Conversely, at low dilution rates the specific toluene degradation rates increased. Excess biomass in a trickle-bed reactor causes reduction of interfacial area and mass transfer, and increase in pressure drop. To avoid these disadvantages, the trickle-bed was moved periodically and biomass was removed with outflowing medium. The concentration of steady state biomass fixed on polyamide beads decreased hyperbolically with the dilution rate. Also, the efficiency of toluene degradation decreased from 72 to 56% with increasing dilution rate while the productivity increased. Potassium limitation generally caused a reduction in biomass, productivity, and yield while the specific degradation increased with dilution rate. This allowed the application of the principles of the chemostat to the trickle-bed reactor described here, for toluene degradation from waste gases. (c) 1997 John Wiley & Sons, Inc. Biotechnol Bioeng 55: 686-692, 1997.

  15. 生物质鼓泡流化床和循环流化床气化对比试验%Comparison of Bubbling Fluidized Bed and Circulating Fluidized Bed in Gasification of Biomass

    Institute of Scientific and Technical Information of China (English)

    范晓旭; 贤建伟; 初雷哲; 杨立国

    2011-01-01

    在内径为φ0.2 m、高6 m的流化床装置上,利用两种不同粒径的石英砂,分别进行了高速鼓泡流化床(BFB)和循环流化床(CFB)的冷态压力分布试验和热态气化试验.结果表明:冷态试验中,鼓泡流化床压力分布主要集中在底部的密相区,循环流化床压力分布更趋均匀.热态稳定气化阶段,循环流化床轴向温差只有40℃,气化的燃气热值、碳转化率和气化效率均高于鼓泡流化床.%The results from biomass gasification in a pilot-scale (6m tall × 0. 2 m internal diameter) air-blown circulating fluidized bed gasifier was tested and compared with bubbling fluidized bed gasifier. The results showed that the diameters of bed material in bubbling fluidized bed and circulating fluidized bed were different. The bubbling fluidized bed had a dense zone and bed material was homogeneous distribution in circulating fluidized bed. The temperature of the circulating fluidized bed was more uniform than bubbling fluidized bed. The carbon conversion rate, gasification efficiency and low gas heat value of circulating fluidized bed were larger than that of bubbling fluidized bed gasifier.

  16. Study on biomass circulation and gasification performance in a clapboard-type internal circulating fluidized bed gasifier.

    Science.gov (United States)

    Zhou, Zhao-qiu; Ma, Long-long; Yin, Xiu-li; Wu, Chuang-zhi; Huang, Li-cheng; Wang, Chu

    2009-01-01

    We investigated the solid particle flow characteristics and biomass gasification in a clapboard-type internal circulating fluidized bed reactor. The effect of fluidization velocity on particle circulation rate and pressure distribution in the bed showed that fluidization velocities in the high and low velocity zones were the main operational parameters controlling particle circulation. The maximum internal circulation rates in the low velocity zone came almost within the range of velocities in the high velocity zone, when u(H)/u(mf)=2.2-2.4 for rice husk and u(H)/u(mf)=3.5-4.5 for quartz sand. In the gasification experiment, the air equivalence ratio (ER) was the main controlling parameter. Rice husk gasification gas had a maximum heating value of around 5000 kJ/m(3) when ER=0.22-0.26, and sawdust gasification gas reached around 6000-6500 kJ/m(3) when ER=0.175-0.24. The gasification efficiency of rice husk reached a maximum of 77% at ER=0.28, while the gasification efficiency of sawdust reached a maximum of 81% at ER=0.25.

  17. Trace elements partitioning during co-firing biomass with lignite in a pilot-scale fluidized bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    Gogebakan, Zuhal [Department of Chemical Engineering, Middle East Technical University, 06531 Ankara (Turkey)], E-mail: zuhalgogebakan@hotmail.com; Selcuk, Nevin [Department of Chemical Engineering, Middle East Technical University, 06531 Ankara (Turkey)], E-mail: selcuk@metu.edu.tr

    2009-03-15

    This study describes the partitioning of 18 trace elements (As, Ba, Cd, Co, Cr, Cu, Li, Mn, Mo, Ni, P, Pb, Sb, Se, Sn, Tl, V, Zn) and 9 major and minor elements (Al, Ca, Fe, K, Mg, Na, S, Si, Ti) during co-firing of olive residue, hazelnut shell and cotton residue with high sulfur and ash content lignite in 0.3 MW{sub t} Middle East Technical University (METU) Atmospheric Bubbling Fluidized Bed Combustor (ABFBC) test rig with limestone addition. Concentrations of trace elements in coal, biomass, limestone, bottom ash, cyclone ash and filter ash were determined by inductively coupled plasma optical emission and mass spectroscopy (ICP-OES and ICP-MS). Partitioning of major and minor elements are influenced by the ash split between the bottom ash and fly ash and that the major proportion of most of the trace elements (As, Ba, Co, Cr, Cu, Li, Mn, Mo, Ni, Pb, Tl, V and Zn) are recovered in fly ash when firing lignite only. Co-firing lignite with biomass enhances partitioning of these elements to fly ash. Co-firing also shifts the partitioning of Cd, P, Sb and Sn from bottom to fly ash.

  18. Nitrifying moving bed biofilm reactor (MBBR) biofilm and biomass response to long term exposure to 1 °C.

    Science.gov (United States)

    Hoang, V; Delatolla, R; Abujamel, T; Mottawea, W; Gadbois, A; Laflamme, E; Stintzi, A

    2014-02-01

    This study aims to investigate moving bed biofilm reactor (MBBR) nitrification rates, nitrifying biofilm morphology, biomass viability as well as bacterial community shifts during long-term exposure to 1 °C. Long-term exposure to 1 °C is the key operational condition for potential ammonia removal upgrade units to numerous northern region treatment systems. The average laboratory MBBR ammonia removal rate after long-term exposure to 1 °C was measured to be 18 ± 5.1% as compared to the average removal rate at 20 °C. Biofilm morphology and specifically the thickness along with biomass viability at various depths in the biofilm were investigated using variable pressure electron scanning microscope (VPSEM) imaging and confocal laser scanning microscope (CLSM) imaging in combination with viability live/dead staining. The biofilm thickness along with the number of viable cells showed significant increases after long-term exposure to 1 °C. Hence, this study observed nitrifying bacteria with higher activities at warm temperatures and a slightly greater quantity of nitrifying bacteria with lower activities at cold temperatures in nitrifying MBBR biofilms. Using DNA sequencing analysis, Nitrosomonas and Nitrosospira (ammonia oxidizers) as well as Nitrospira (nitrite oxidizer) were identified and no population shift was observed between 20 °C and after long-term exposure to 1 °C.

  19. Development of Methane and Nitrous Oxide Emission Factors for the Biomass Fired Circulating Fluidized Bed Combustion Power Plant

    Directory of Open Access Journals (Sweden)

    Chang-Sang Cho

    2012-01-01

    Full Text Available This study makes use of this distinction to analyze the exhaust gas concentration and fuel of the circulating fluidized bed (CFB boiler that mainly uses wood biomass, and to develop the emission factors of Methane (CH4, Nitrous oxide (N2O. The fuels used as energy sources in the subject working sites are Wood Chip Fuel (WCF, RDF and Refused Plastic Fuel (RPF of which heating values are 11.9 TJ/Gg, 17.1 TJ/Gg, and 31.2 TJ/Gg, respectively. The average concentrations of CH4 and N2O were measured to be 2.78 ppm and 7.68 ppm, respectively. The analyzed values and data collected from the field survey were used to calculate the emission factor of CH4 and N2O exhausted from the CFB boiler. As a result, the emission factors of CH4 and N2O are 1.4 kg/TJ (0.9–1.9 kg/TJ and 4.0 kg/TJ (2.9–5.3 kg/TJ within a 95% confidence interval. Biomass combined with the combustion technology for the CFB boiler proved to be more effective in reducing the N2O emission, compared to the emission factor of the CFB boiler using fossil fuel.

  20. Development of methane and nitrous oxide emission factors for the biomass fired circulating fluidized bed combustion power plant.

    Science.gov (United States)

    Cho, Chang-Sang; Sa, Jae-Hwan; Lim, Ki-Kyo; Youk, Tae-Mi; Kim, Seung-Jin; Lee, Seul-Ki; Jeon, Eui-Chan

    2012-01-01

    This study makes use of this distinction to analyze the exhaust gas concentration and fuel of the circulating fluidized bed (CFB) boiler that mainly uses wood biomass, and to develop the emission factors of Methane (CH(4)), Nitrous oxide (N(2)O). The fuels used as energy sources in the subject working sites are Wood Chip Fuel (WCF), RDF and Refused Plastic Fuel (RPF) of which heating values are 11.9 TJ/Gg, 17.1 TJ/Gg, and 31.2 TJ/Gg, respectively. The average concentrations of CH(4) and N(2)O were measured to be 2.78 ppm and 7.68 ppm, respectively. The analyzed values and data collected from the field survey were used to calculate the emission factor of CH(4) and N(2)O exhausted from the CFB boiler. As a result, the emission factors of CH(4) and N(2)O are 1.4 kg/TJ (0.9-1.9 kg/TJ) and 4.0 kg/TJ (2.9-5.3 kg/TJ) within a 95% confidence interval. Biomass combined with the combustion technology for the CFB boiler proved to be more effective in reducing the N(2)O emission, compared to the emission factor of the CFB boiler using fossil fuel.

  1. 2009 PILOT SCALE FLUIDIZED BED STEAM REFORMING TESTING USING THE THOR (THERMAL ORGANIC REDUCTION) PROCESS: ANALYTICAL RESULTS FOR TANK 48H ORGANIC DESTRUCTION - 10408

    Energy Technology Data Exchange (ETDEWEB)

    Williams, M.; Jantzen, C.; Burket, P.; Crawford, C.; Daniel, G.; Aponte, C.; Johnson, C.

    2009-12-28

    The Savannah River Site (SRS) must empty the contents of Tank 48H, a 1.3 million gallon Type IIIA HLW storage tank, to return this tank to service. The tank contains organic compounds, mainly potassium tetraphenylborate that cannot be processed downstream until the organic components are destroyed. The THOR{reg_sign} Treatment Technologies (TTT) Fluidized Bed Steam Reforming (FBSR) technology, herein after referred to as steam reforming, has been demonstrated to be a viable process to remove greater than 99.9% of the organics from Tank 48H during various bench scale and pilot scale tests. These demonstrations were supported by Savannah River Remediation (SRR) and the Department of Energy (DOE) has concurred with the SRR recommendation to proceed with the deployment of the FBSR technology to treat the contents of Tank 48H. The Savannah River National Laboratory (SRNL) developed and proved the concept with non-radioactive simulants for SRR beginning in 2003. By 2008, several pilot scale campaigns had been completed and extensive crucible testing and bench scale testing were performed in the SRNL Shielded Cells using Tank 48H radioactive sample. SRNL developed a Tank 48H non-radioactive simulant complete with organic compounds, salt, and metals characteristic of those measured in a sample of the radioactive contents of Tank 48H. FBSR Pilot Scaled Testing with the Tank 48H simulant has demonstrated the ability to remove greater than 98% of the nitrites and greater than 99.5% of the nitrates from the Tank 48H simulant, and to form a solid product that is primarily alkali carbonate. The alkali carbonate is soluble and, thus, amenable to pumping as a liquid to downstream facilities for processing. The FBSR technology was demonstrated in October of 2006 in the Engineering Scale Test Demonstration (ESTD) pilot scale steam reformer at the Hazen Research Inc. (HRI) facility in Golden, CO. Additional ESTD tests were completed in 2008 and in 2009 that further demonstrated the

  2. DEVELOPMENT AND EVALUATION OF A LOW-DENSITY BIOMASS FEEDING SYSTEM FOR FLUIDIZED BED GASIFIERS

    Directory of Open Access Journals (Sweden)

    A. E. Ghaly

    2013-01-01

    Full Text Available For efficient operation of a biomass gasifier, the biomass material must be fed continuously to the system. A feeding system for chopped straw and rice husk was designed, constructed and evaluated. It consisted of: a frame, a hopper, an auger, two agitators, a drive system and a power unit. Initial testing showed that wheat straw and rice husk, being highly cohesive materials, created tunnel flow and piping conditions. This occurs when the pressure above an impending dome of material is too small resulting in the creation of a stable dome and blockage of the discharge. In order to achieve good flow conditions, it was concluded that the hopper must operate under "mass outflow" and the material should not be allowed to build up along the flow channels. These objectives were achieved by the proper redesign of the hopper configuration, the installation of agitators in the hopper and use of an auger in the outlet duct leading into the gasifier. However, as the augur was used to move the biomass material from hopper to the gasifier, it was observed that hot gases leaked from the gasifier into the hopper and heat was also transmitted from the gasifier to the hopper though the augur shaft by conduction resulting in burning of biomass material in the hopper. Therefore, the augur shaft was fitted with copper tubing to serve as a water cooling system and the tapered section of the augur was fitted with a stainless steel section with water inlet and outlet to serve as a secondary cooling system. After, the system has been successfully modified for feeding wheat straw and rice husk, it was tested to determine the optimum operating conditions. Mass flow tests were performed with four sprocket combinations and four auger speeds. Increasing the auger speed and/or the lower agitator speed increased the straw output of the feeding system. However, increases in the upper agitator speed resulted in reduced mass flow of the material due to the mixing effect created

  3. Flow behavior inside a novel rotating fluidized bed for solar gasification of biomass

    Science.gov (United States)

    Lu, Zhao; Jafarian, Mehdi; Chinnici, Alfonso; Arjomandi, Maziar; Nathan, Graham J.

    2017-06-01

    The present paper reports a numerical investigation of the iso-thermal flow field and particle deposition onto the reactor window of a novel concept of Rotating Fluidized Bed Solar Reactor (RFBSR) and their sensitivity to reactor inner diameter. The RFBSR differs from conventional fluidized bed solar reactors in that it relies on the centrifugal force generated through rotation to counteract the drag force produced by the fluidizing gas on the particles. A three dimensional Computational Fluid Dynamics (CFD) model of the RFBSR was developed and combined with a Lagrangian particle tracking model to investigate the flow velocity components at various locations and particle concentration onto the window surface. The CFD model was partially verified by comparing its predictions with the published experimental measurements in a rotating porous cylindrical vessel with a radially injected flow. It was found that the Baseline Reynold Stress Model (RSM BSL) produces more agreeable predictions with the experimental measurements than Re-Normalization Group (RNG) k-ɛ and k-ω Shear Stress Transport (SST) models. Also, it was found that for the reactor configurations investigated here, reducing the reactor diameter has the effects of increasing the core axial flow velocity and particle deposition onto the window. The results presented assist in developing an understanding of the operation of the RFBSR.

  4. Fundamental studies of synthesis-gas production based on fluidised-bed gasification of biomass (UCGFunda)

    Energy Technology Data Exchange (ETDEWEB)

    Reinikainen, M.; Moilanen, A.; Simell, P.; Hannula, I.; Nasrullah, M.; Kurkela, E. (VTT Technical Research Centre of Finland, Espoo (Finland))

    2009-10-15

    The research is directed towards methods of producing transportation bio-fuels via the synthesis-gas route, with emphasis on the synthesis-gas production and gas cleaning steps. The subtopics of the research project are (1) fuel characterisation and ash behaviour in the gasification step, (2) reaction mechanisms related to gas cleaning, (3) evaluations of alternative process configurations and applications and (4) international co-operation. VTT itself finances also two additional subtopics: (5) new analysis techniques and (6) hydrogen from biomass via gasification. A lot of data on the reactivity and ash sintering properties of various kinds of biomasses has been obtained in the project and the information will now be formulated into a mathematical model. In addition to catalysis also thermal reactions play an important role in gas cleaning. Both experimental and modelling work on both of the reaction types is being carried out. Three techno-economic evaluations on alternative and competing technologies will be completed in the coming year. International development in syngas technology has been closely monitored in all subtopics as well as by participating in relevant IEA-tasks. New analysis techniques developed in the project have proven very useful and for instance a fast on-line tar analysis method is now well established. (orig.)

  5. Biomass gasification in fixed bed type down draft: theoretical and experimental aspects; Gasificacao de biomassa em leito fixo tipo concorrente: aspectos teoricos e experimentais

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Juan Daniel; Andrade, Rubenildo Vieira; Lora, Electo Eduardo Silva [Universidade Federal de Itajuba (UNIFEI), MG (Brazil). Inst. de Engenharia Mecanica. Nucleo de Excelencia em Geracao Termeletrica e Distribuida

    2008-07-01

    Actually are recognizing the advantages of biomass in reducing dependence on fossil fuels and significant reduction in emissions of greenhouse effect gases such as Co2. Also are known the different conversion of biomass routes for their use or exploitation, such as thermochemical process (gasification, pyrolysis and combustion), the biological process (fermentation and transesterification) and the physical process (densification, reducing grain and mechanical pressing). In this sense, the gasification is regarded as the most promising mechanism to obtain a homogeneous gaseous fuel with sufficient quality in the small scale distributed generation. This work presents some aspects of biomass gasification in fixed bed, as well as some preliminary results in the evaluation and operation of fixed bed down draft gasifier with double stage air supply of the NEST, identifying the adequate air supply quantity (equivalence ratio in the range of 0,35 to 0,45) for obtaining a fuel gas with lower heating value around 4 MJ/N m3. (author)

  6. Fundamental studies of synthesis-gas production based on fluidised-bed gasification of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Reinikainen, M.; Moilanen, A.; Simell, P.; McKeough, P.; Hannula, I. (VTT Technical Research Centre of Finland, Espoo (Finland))

    2008-07-01

    The research is directed towards methods of producing transportation bio-fuels via the synthesis-gas route, with emphasis on the synthesis-gas production and gas cleaning steps. The project will both broaden and deepen the knowledge base and, in particular, will generate new fundamental information about the most critical process steps from the point of view of the realisation of the technology. The results will be exploited in the ongoing industrial-driven development and demonstration projects. The subtopics of the research project are (1) fuel characterisation and ash behaviour in the gasification step, (2) reaction mechanisms related to gas cleaning, in particular the reactions of hydrocarbons at gasification temperatures, during hot-gas filtration and on catalytic surfaces, (3) evaluations of alternative process configurations and applications and (4) monitoring of developments elsewhere in the world. In addition VTT itself finances two additions subtopics (5) new analysis techniques and (6) hydrogen from biomass via gasification. (orig.)

  7. Fundamental studies of synthesis-gas production based on fluidised-bed gasification of biomass - UCGFunda

    Energy Technology Data Exchange (ETDEWEB)

    Reinikainen, M.; Moilanen, A.; Simell, P.; Hannula, I.; Kurkela, E. (VTT Technical Research Centre of Finland, Espoo (Finland)), Email: matti.reinikainen@vtt.fi; Suominen, T.P. (Aabo Akademi, Turku (Finland). Lab. of Industrial Chemistry and Reaction Engineering); Linnekoski, J.; Roenkkoenen, E. (Aalto University, School of Science and Technology, Espoo (Finland). Lab. of Industrial Chemistry.)

    2010-10-15

    The research is directed towards methods of producing transportation bio-fuels via the synthesis-gas route, with emphasis on the synthesis-gas production and gas cleaning steps. The subtopics of the research project are (1) fuel characterisation and ash behaviour in the gasification step, (2) reaction mechanisms related to gas cleaning, (3) evaluations of alternative process configurations and applications and (4) international cooperation. VTT itself finances also two additional subtopics: (5) new analysis techniques and (6) hydrogen from biomass via gasification. The project comprises experimental work, modelling, techno-economic evaluations as well as studies based on literature. The project is steered by a wide industrial consortium and the research work is carried out by VTT, Aalto University and Aabo Akademi. International development in syngas technology has been closely monitored in all subtopics as well as by participating in relevant IEA-tasks. (orig.)

  8. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank SX-105 And AN-103) By Fluidized Bed Steam Reformation

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, Carol; Herman, Connie; Crawford, Charles; Bannochie, Christopher; Burket, Paul; Daniel, Gene; Cozzi, Alex; Nash, Charles; Miller, Donald; Missimer, David

    2014-01-10

    One of the immobilization technologies under consideration as a Supplemental Treatment for Hanford’s Low Activity Waste (LAW) is Fluidized Bed Steam Reforming (FBSR). The FBSR technology forms a mineral waste form at moderate processing temperatures thus retaining and atomically bonding the halides, sulfates, and technetium in the mineral phases (nepheline, sodalite, nosean, carnegieite). Additions of kaolin clay are used instead of glass formers and the minerals formed by the FBSR technology offers (1) atomic bonding of the radionuclides and constituents of concern (COC) comparable to glass, (2) short and long term durability comparable to glass, (3) disposal volumes comparable to glass, and (4) higher Na2O and SO{sub 4} waste loadings than glass. The higher FBSR Na{sub 2}O and SO{sub 4} waste loadings contribute to the low disposal volumes but also provide for more rapid processing of the LAW. Recent FBSR processing and testing of Hanford radioactive LAW (Tank SX-105 and AN-103) waste is reported and compared to previous radioactive and non-radioactive LAW processing and testing.

  9. Morphological study of biomass during the start-up period of a fixed-bed anaerobic reactor treating domestic sewage

    Directory of Open Access Journals (Sweden)

    Cláudio Antonio Andrade Lima

    2005-09-01

    Full Text Available This work focused on a morphological study of the microorganisms attached to polyurethane foam matrices in a horizontal-flow anaerobic immobilized biomass (HAIB reactor treating domestic sewage. The experiments consisted of monitoring the biomass colonization process of foam matrices in terms of the amount of retained biomass and the morphological characteristics of the cells attached to the support during the start-up period. Non-fluorescent rods and cocci were found to predominate in the process of attachment to the polyurethane foam surface. From the 10th week of operation onwards, an increase was observed in the morphological diversity, mainly due to rods, cocci, and Methanosaeta-like archaeal cells. Hydrodynamic problems, such as bed clogging and channeling occurred in the fixed-bed reactor, mainly due to the production of extracellular polymeric substances and their accumulation in the interstices of the bed causing a gradual deterioration of its performance, which eventually led to the system's collapse. These results demonstrated the importance and usefulness of monitoring the dynamics of the formation of biofilm during the start-up period of HAIB reactors, since it allowed the identification of operational problems.Este trabalho apresenta um estudo morfológico de microrganismos aderidos à espuma de poliuretano em reator anaeróbio horizontal de leito fixo (RAHLF, aplicado ao tratamento de esgoto sanitário. O processo de colonização do suporte pela biomassa anaeróbia e as características morfológicas das células aderidas foram monitorados durante o período de partida do reator. Bacilos e cocos não fluorescentes foram predominantes no processo de aderência direta à espuma de poliuretano. Aumento na diversidade biológica foi observado a partir da 10ª semana de operação do reator, com predominância de bacilos, cocos e arqueas metanogênicas semelhantes a Methanosaeta. Problemas hidrodinâmicos, tais como formação de

  10. An Experimental and Numerical Investigation of Fluidized Bed Gasification of Solid Waste

    OpenAIRE

    Sharmina Begum; Mohammad G. Rasul; Delwar Akbar; David Cork

    2013-01-01

    Gasification is a thermo-chemical process to convert carbon-based products such as biomass and coal into a gas mixture known as synthetic gas or syngas. Various types of gasification methods exist, and fluidized bed gasification is one of them which is considered more efficient than others as fuel is fluidized in oxygen, steam or air. This paper presents an experimental and numerical investigation of fluidized bed gasification of solid waste (SW) (wood). The experimental measurement of syngas...

  11. Modified Thermodynamic Equilibrium Model for Biomass Gasification: A Study of the Influence of Operating Conditions

    DEFF Research Database (Denmark)

    Puig Arnavat, Maria; Bruno, Juan Carlos; Coronas, Alberto

    2012-01-01

    data from different authors for downdraft, fluidized-bed gasifiers and different biomasses, showing good agreement between reported data and modeled values. In addition, it has been used to evaluate the influence of different operating parameters [equivalence ratio (ER), air preheating, steam injection...

  12. Biological conversion of forage sorghum biomass to ethanol by steam explosion pretreatment and simultaneous hydrolysis and fermentation at high solid content

    Energy Technology Data Exchange (ETDEWEB)

    Manzanares, Paloma; Ballesteros, Ignacio; Negro, Maria Jose; Oliva, Jose Miguel; Gonzalez, Alberto; Ballesteros, Mercedes [Renewable Energy Department-CIEMAT, Biofuels Unit, Madrid (Spain)

    2012-06-15

    In this work, forage sorghum biomass was studied as feedstock for ethanol production by a biological conversion process comprising the steps of hydrothermal steam explosion pretreatment, enzymatic hydrolysis with commercial enzymes, and fermentation with the yeast Saccharomyces cerevisiae. Steam explosion conditions were optimized using a response surface methodology considering temperature (180-230 C) and time (2-10 min). Sugar recovery in the pretreatment and the enzymatic digestibility of the pretreated solid were used to determine the optimum conditions, i.e., 220 C and 7 min. At these conditions, saccharification efficiency attained 89 % of the theoretical and the recovery of xylose in the prehydrolyzate accounted for 35 % of the amount of xylose present in raw material. Then, a simultaneous hydrolysis and fermentation (SSF) process was tested at laboratory scale on the solid fraction of forage sorghum pretreated at optimum condition, in order to evaluate ethanol production. The effect of the enzyme dose and the supplementation with xylanase enzyme of the cellulolytic enzyme cocktail was studied at increasing solid concentration up to 18 % (w/w) in SSF media. Results show good performance of SSF in all consistencies tested with a significant effect of increasing enzyme load in SSF yield and final ethanol concentration. Xylanase supplementation allows increasing solid concentration up to 18 % (w/w) with good SSF performance and final ethanol content of 55 g/l after 4-5 days. Based on this result, about 190 l of ethanol could be obtained from 1 t of untreated forage sorghum, which means a transformation yield of 85 % of the glucose contained in the feedstock. (orig.)

  13. Thermal processing of biomass natural fibre wastes by pyrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Reed, Anton R.; Williams, Paul T. [Leeds Univ., Dept. of Fuel and Energy, Leeds (United Kingdom)

    2003-07-01

    Waste biomass material in the form of natural fibres used in the production of textile products were examined for their potential to produce activated carbon by physical activation. The five biomass types were hemp, flax, jute, coir and abaca. Each biomass was pyrolysed in a fixed bed reactor and the char characterized. The char was subsequently, activated with steam in a char activation reactor. The surface area and porosity of the derived activated carbon was determined. Surface areas of between 770 and 879 m{sup 2} g{sup -1} were achieved. The yield of activated carbon was mostly less than 20 wt% of the original biomass. The five biomass samples were also pyrolysed in a thermogravimetric analyser. The thermal degradation of the biomass samples were discussed in terms of the thermal degradation of the main components of the biomass, cellulose, hemicellulose and lignin. (Author)

  14. Results concerning a clean co-combustion technology of waste biomass with fossil fuel, in a pilot fluidised bed combustion facility

    Energy Technology Data Exchange (ETDEWEB)

    Ionel, Ioana; Trif-Tordai, Gavril; Ungureanu, Corneliu; Popescu, Francisc; Lontis, Nicolae [Politehnica Univ. Timisoara (Romania). Faculty for Mechanical Engineering

    2008-07-01

    The research focuses on a facility, the experimental results, interpretation and future plans concerning a new developed technology of using waste renewable energy by applying the cocombustion of waste biomass with coal, in a fluidised bed system. The experimental facility is working entirely in accordance to the allowed limits for the exhaust flue gas concentration, with special concern for typical pollutants. The experiments conclude that the technology is cleaner, has as main advantage the possibility to reduce both the SO{sub 2} and CO{sub 2} exhaust in comparison to standard fossil fuel combustion, under comparable circumstances. The combustion is occurring in a stable fluidised bed. (orig.)

  15. Investigation of ash deposition in a pilot-scale fluidized bed combustor co-firing biomass with lignite

    Energy Technology Data Exchange (ETDEWEB)

    Gogebakan, Z.; Gogebakan, Y.; Selcuk, N.; Seliuk, E. [Middle East Technical University, Ankara (Turkey). Dept. of Chemical Engineering

    2009-01-15

    This study presents the results from investigation of ash deposition characteristics of a high ash and sulfur content lignite co-fired with three types of biomass (olive residue, 49 wt%; hazelnut shell, 42 wt%; and cotton residue, 41 wt%) in 0.3 MWt Middle East Technical University (METU) Atmospheric Bubbling Fluidized Bed Combustion (ABFBC) Test Rig. Deposit samples were collected on all air-cooled probe at a temperature of 500{degree}C. Samples were analyzed by SEM/EDX and XRD methods. The results reveal that co-firing lignite with olive residue, hazelnut shell and cotton residue show low deposition rates. High concentrations of silicon, calcium, sulfur, iron, and aluminum were found in deposit samples. No chlorine was detected in deposits. Calcium sulfate and potassium sulfate were detected as major and minor components of the deposits, respectively. High sulfur and alumina-silicate content of lignite resulted in formation of alkali sulfates instead of alkali chlorides. Therefore, fuel blends under consideration can be denoted to have low-fouling propensity.

  16. Investigation of ash deposition in a pilot-scale fluidized bed combustor co-firing biomass with lignite.

    Science.gov (United States)

    Gogebakan, Zuhal; Gogebakan, Yusuf; Selçuk, Nevin; Selçuk, Ekrem

    2009-01-01

    This study presents the results from investigation of ash deposition characteristics of a high ash and sulfur content lignite co-fired with three types of biomass (olive residue, 49 wt%; hazelnut shell, 42 wt%; and cotton residue, 41 wt%) in 0.3 MW(t) Middle East Technical University (METU) Atmospheric Bubbling Fluidized Bed Combustion (ABFBC) Test Rig. Deposit samples were collected on an air-cooled probe at a temperature of 500 degrees C. Samples were analyzed by SEM/EDX and XRD methods. The results reveal that co-firing lignite with olive residue, hazelnut shell and cotton residue show low deposition rates. High concentrations of silicon, calcium, sulfur, iron, and aluminum were found in deposit samples. No chlorine was detected in deposits. Calcium sulfate and potassium sulfate were detected as major and minor components of the deposits, respectively. High sulfur and alumina-silicate content of lignite resulted in formation of alkali sulfates instead of alkali chlorides. Therefore, fuel blends under consideration can be denoted to have low-fouling propensity.

  17. Techno-economic analysis of sorption-enhanced steam methane reforming in a fixed bed reactor network integrated with fuel cell

    Science.gov (United States)

    Diglio, Giuseppe; Hanak, Dawid P.; Bareschino, Piero; Mancusi, Erasmo; Pepe, Francesco; Montagnaro, Fabio; Manovic, Vasilije

    2017-10-01

    Sorption-enhanced steam methane reforming (SE-SMR) is a promising alternative for H2 production with inherent CO2 capture. This study evaluates the techno-economic performance of SE-SMR in a network of fixed beds and its integration with a solid oxide fuel cell (SE-SMR-SOFC) for power generation. The analysis revealed that both proposed systems are characterised by better economic performance than the reference systems. In particular, for SE-SMR the levelised cost of hydrogen is 1.6 €ṡkg-1 and the cost of CO2 avoided is 29.9 €ṡtCO2-1 (2.4 €ṡkg-1 and 50 €ṡtCO2-1, respectively, for SMR with CO2 capture) while for SE-SMR-SOFC the levelised cost of electricity is 0.078 €ṡkWh-1 and the cost of CO2 avoided is 36.9 €ṡtCO2-1 (0.080 €ṡkWh-1 and 80 €ṡtCO2-1, respectively, for natural gas-fired power plant with carbon capture). The sensitivity analysis showed that the specific cost of fuel and the capital cost of fuel cell mainly affect the economic performance of SE-SMR and SE-SMR-SOFC, respectively. The daily revenue of the SE-SMR-SOFC system is higher than that of the natural gas-fired power plant if the difference between the carbon tax and the CO2 transport and storage cost is > 6 €ṡtCO2-1.

  18. Process for purifying geothermal steam

    Science.gov (United States)

    Li, C.T.

    Steam containing hydrogen sulfide is purified and sulfur recovered by passing the steam through a reactor packed with activated carbon in the presence of a stoichiometric amount of oxygen which oxidizes the hydrogen sulfide to elemental sulfur which is adsorbed on the bed. The carbon can be recycled after the sulfur has been recovered by vacuum distillation, inert gas entrainment or solvent extraction. The process is suitable for the purification of steam from geothermal sources which may also contain other noncondensable gases.

  19. Sustainable production of syngas from biomass-derived glycerol by steam reforming over highly stable Ni/SiC.

    Science.gov (United States)

    Kim, Sung Min; Woo, Seong Ihl

    2012-08-01

    The production of syngas was investigated by steam reforming glycerol over Ni/Al(2)O(3), Ni/CeO(2), and Ni/SiC (which have acidic, basic, and neutral properties) at temperatures below 773 K. The complete and stable conversion of glycerol with a yield (higher than 90 %) of gaseous products (mainly syngas) was achieved over Ni/SiC during a 60 h reaction, whereas the conversion of glycerol continually decreases over Ni/Al(2)O(3) (by 49.8 %) and Ni/CeO(2) (by 77.1 %). The deactivation of Ni/Al(2)O(3) and Ni/CeO(2) is mainly caused by coke deposition because of the C-C cleavage of the byproducts produced by dehydration over acidic sites and condensation over basic sites. Gaseous products with a 1.0-1.9 syngas ratio (H(2)/CO) are produced over Ni/SiC. This ratio is required for the Fischer-Tropsch synthesis. However, a syngas ratio of more than 3.0 was observed over Ni/Al(2)O(3) and Ni/CeO(2) because of the high activity of the water-gas-shift reaction. Any dissociative or associative adsorption of water on Al(2)O(3) and CeO(2) promotes a water-gas-shift reaction and produces a higher syngas ratio. H(2) and CO were mainly produced by decomposition of glycerol through dehydrogenation and decarbonylation over Ni sites. Thus, SiC promotes an intrinsic contribution of nickel (dehydrogenation, and decarbonylation) without any byproducts from the dehydration and condensation.

  20. 双流化床生物质气化炉研究进展%Research progress of dual fluidized bed biomass gasifier

    Institute of Scientific and Technical Information of China (English)

    王晓明; 肖显斌; 刘吉; 陈旭娇; 覃吴; 董长青; 李文艳

    2015-01-01

    生物质是重要的清洁可再生能源,双流化床生物质气化技术是将低品位的生物质能转化成高品位氢能的重要途径。本文阐明了双流化床气化过程的基本原理,从燃气中氢气浓度、焦油含量和装置热效率等角度,介绍了双流化床生物质气化技术的早期探索和发展现状,对目前几种典型双流化床生物质气化炉的炉型设计及相关试验研究进行了分析和总结。指出内循环双流化床气化炉结构虽然简单紧凑,但是难以避免气化室和燃烧室之间的气体串混问题;而外循环流化床通过外置返料器很好地解决了气体串混问题。分析了不同气化室优化设计方案对提升燃气品质的理论依据及其优缺点。最后对双流化床生物质气化技术的发展进行了总结和展望,指出双流化床生物质气化制氢具有非常广阔的工业化应用和发展前景。%Biomass is an important part of clean and renewable energy sources. Dual fluidized bed biomass gasification is an important technology that transforms low-quality biomass into high-quality hydrogen. This paper illustrates the basic principles of the dual fluidized bed gasification process,and summarizes the early exploration and development status of the dual fluidized bed biomass gasification technology from the perspective of hydrogen concentration,tar content and device thermal efficiency. The furnace design and related experimental studies of several typical dual fluidized bed biomass gasifiers are analyzed and summarized. Internal circulating dual fluidized bed gasification furnace has simple and compact structure,but it is difficult to prevent gas leakage between gasification chamber and combustion chamber. External circulating dual fluidized bed with external recycle device resolves the problem of gas leakage. The theoretical basis,advantages and disadvantages of different optimized gasification chamber designs are analyzed. The

  1. Improved yield parameters in catalytic steam gasification of forestry residue; optimizing biomass feed rate and catalyst type

    Energy Technology Data Exchange (ETDEWEB)

    Corujo, Andrea; Yerman, Luis; Arizaga, Beatriz; Brusoni, Mariana; Castiglioni, Jorge [Laboratorio de Fisicoquimica de Superficies, DETEMA Facultad de Quimica, Universidad de la Republica, Gral. Flores 2124, CC 1157, 11800-Montevideo (Uruguay)

    2010-12-15

    The catalytic gasification (900 C) of forestry industry residue (Eucalyptus saligna) was laboratory-studied. Biomass feed rate and type and amount of catalyst were assayed for their effect on the gasified product composition and the overall energy yield of the gasification reaction. The use of a calcined dolomite catalyst resulted in a combustible gas mixture of adequate calorific power (10.65 MJ m{sup -3}) for use as fuel, but neither the product gas composition nor the energy yield varied significantly with widely different amounts of the catalyst (2 g and 20 g). The use of NiO-loaded calcined dolomite catalysts did not affect the product gas composition significantly but led to a 30% increase in the total product gas volume and to a reduction in the rate of tar and char formation. The catalyst loaded with the smallest amount of NiO studied (0.4 wt%. Ni/Dol) led to the highest energy yield (21.50 MJ kg{sup -1} on a dry-wood basis) based on the use of the gasified product as fuel. The gasified product was found to have an adequate H{sub 2}/CO molar ratio and H{sub 2} content for use as synthesis gas source and partial source of H{sub 2}. (author)

  2. RADIOACTIVE DEMONSTRATION OF FINAL MINERALIZED WASTE FORMS FOR HANFORD WASTE TREATMENT PLANT SECONDARY WASTE BY FLUIDIZED BED STEAM REFORMING USING THE BENCH SCALE REFORMER PLATFORM

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C.; Burket, P.; Cozzi, A.; Daniel, W.; Jantzen, C.; Missimer, D.

    2012-02-02

    The U.S. Department of Energy's Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as {sup 137}Cs, {sup 129}I, {sup 99}Tc, Cl, F, and SO{sub 4} that volatilize at the vitrification temperature of 1150 C in the absence of a continuous cold cap (that could minimize volatilization). The current waste disposal path for the WTP-SW is to process it through the Effluent Treatment Facility (ETF). Fluidized Bed Steam Reforming (FBSR) is being considered for immobilization of the ETF concentrate that would be generated by processing the WTP-SW. The focus of this current report is the WTP-SW. FBSR offers a moderate temperature (700-750 C) continuous method by which WTP-SW wastes can be processed irrespective of whether they contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline

  3. RADIOACTIVE DEMONSTRATIONS OF FLUIDIZED BED STEAM REFORMING AS A SUPPLEMENTARY TREATMENT FOR HANFORD'S LOW ACTIVITY WASTE AND SECONDARY WASTES

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C.; Crawford, C.; Cozzi, A.; Bannochie, C.; Burket, P.; Daniel, G.

    2011-02-24

    The U.S. Department of Energy's Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford's tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP's LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as Cs-137, I-129, Tc-99, Cl, F, and SO4 that volatilize at the vitrification temperature of 1150 C in the absence of a continuous cold cap. The current waste disposal path for the WTP-SW is to recycle it to the supplemental LAW treatment to avoid a large steady state accumulation in the pretreatment-vitrification loop. Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750 C) continuous method by which LAW and/or WTP-SW wastes can be processed irrespective of whether they contain organics, nitrates, sulfates

  4. ALTENER - Biomass event in Finland

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The publication contains the lectures held in the Biomass event in Finland. The event was divided into two sessions: Fuel production and handling, and Co-combustion and gasification sessions. Both sessions consisted of lectures and the business forum during which the companies involved in the research presented themselves and their research and their equipment. The fuel production and handling session consisted of following lectures and business presentations: AFB-NETT - business opportunities for European biomass industry; Wood waste in Europe; Wood fuel production technologies in EU- countries; new drying method for wood waste; Pellet - the best package for biofuel - a view from the Swedish pelletmarket; First biomass plant in Portugal with forest residue fuel; and the business forum of presentations: Swedish experiences of willow growing; Biomass handling technology; Chipset 536 C Harvester; KIC International. The Co-combustion and gasification session consisted of following lectures and presentations: Gasification technology - overview; Overview of co-combustion technology in Europe; Modern biomass combustion technology; Wood waste, peat and sludge combustion in Enso Kemi mills and UPM-Kymmene Rauma paper mill; Enhanced CFB combustion of wood chips, wood waste and straw in Vaexjoe in Sweden and Grenaa CHP plant in Denmark; Co-combustion of wood waste; Biomass gasification projects in India and Finland; Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti (FI); Biomass gasification for energy production, Noord Holland plant in Netherlands and Arbre Energy (UK); Gasification of biomass in fixed bed gasifiers, Wet cleaning and condensing heat recovery of flue gases; Combustion of wet biomass by underfeed grate boiler; Research on biomass and waste for energy; Engineering and consulting on energy (saving) projects; and Research and development on combustion of solid fuels

  5. Catalytic gasification of biomass (Miscanthus) enhanced by CO2 sorption.

    Science.gov (United States)

    Zamboni, I; Debal, M; Matt, M; Girods, P; Kiennemann, A; Rogaume, Y; Courson, C

    2016-11-01

    The main objective of this work concerns the coupling of biomass gasification reaction and CO2 sorption. The study shows the feasibility to promote biomass steam gasification in a dense fluidized bed reactor with CO2 sorption to enhance tar removal and hydrogen production. It also proves the efficiency of CaO-Ca12Al14O33/olivine bi-functional materials to reduce heavy tar production. Experiments have been carried out in a fluidized bed gasifier using steam as the fluidizing medium to improve hydrogen production. Bed materials consisting of CaO-based oxide for CO2 sorption (CaO-Ca12Al14O33) deposited on olivine for tar reduction were synthesized, their structural and textural properties were characterized by Brunauer-Emmett-Teller (BET), X-ray diffraction (XRD), and temperature-programmed reduction (TPR) methods, and the determination of their sorption capacity and stability analyzed by thermogravimetric analysis (TGA). It appears that this CaO-Ca12Al14O33/olivine sorbent/catalyst presents a good CO2 sorption stability (for seven cycles of carbonation/decarbonation). Compared to olivine and Fe/olivine in a fixed bed reactor for steam reforming of toluene chosen as tar model compound, it shows a better hydrogen production rate and a lower CO2 selectivity due to its sorption on the CaO phase. In the biomass steam gasification, the use of CaO-Ca12Al14O33/olivine as bed material at 700 °C leads to a higher H2 production than olivine at 800 °C thanks to CO2 sorption. Similar tar concentration and lighter tar production (analyzed by HPLC/UV) are observed. At 700 °C, sorbent addition allows to halve tar content and to eliminate the heaviest tars.

  6. Release of K, Cl, and S during combustion and co-combustion with wood of high-chlorine biomass in bench and pilot scale fuel beds

    DEFF Research Database (Denmark)

    Johansen, Joakim Myung; Aho, Martti; Paakkinen, Kari

    2013-01-01

    Studies of the release of critical ash-forming elements from combustion of biomass are typically conducted with small sample masses under well controlled conditions. In biomass combustion on a grate, secondary recapture and release reactions in the fuel-bed may affect the overall release...... and partitioning of these elements. Earlier work by the authors on the release of K, Cl, and S from a high-chlorine biomass (corn stover) in a lab-scale setup is, in the present work, supplemented with novel results from a bench-scale fixed bed reactor and a 100kW moving grate pilot facility. The results from...... the bench-scale reactor indicate that S and K release are not significantly affected by secondary reactions, while Cl is partly recaptured by secondary reactions in the char. A linear increase in K-release was observed from 50% at 906°C to almost 80wt.% at 1234°C when firing only corn stover. A similar...

  7. Strategies to reduce gaseous KCl and chlorine in deposits during combustion of biomass in fluidised bed boilers

    Energy Technology Data Exchange (ETDEWEB)

    Kassman, Haakan

    2012-11-01

    Combustion of a biomass with an enhanced content of alkali and chlorine (Cl) can result in operational problems including deposit formation and superheater corrosion. The strategies applied to reduce such problems include co-combustion and the use of additives. In this work, measures were investigated in order to decrease the risk of superheater corrosion by reducing gaseous KCl and the content of chlorine in deposits. The strategies applied were sulphation of KCl by sulphur/sulphate containing additives (i.e. elemental sulphur (S) and ammonium sulphate (AS)) and co-combustion with peat. Both sulphation of KCl and capture of potassium (K) in ash components can be of importance when peat is used. The experiments were mainly performed in a 12 MW circulation fluidised bed (CFB) boiler equipped for research purposes but also in a full-scale CFB boiler. The results were evaluated by means of IACM (on-line measurements of gaseous KCl), conventional gas analysis, deposit and corrosion probe measurements and ash analysis. Ammonium sulphate performed significantly better than elemental sulphur. Thus the presence of SO{sub 3} (i.e. AS) is of greater importance than that of SO{sub 2} (i.e. S) for sulphation of gaseous KCl and reduction of chlorine in deposits. Only a minor reduction of gaseous KCl was obtained during co-combustion with peat although chlorine in the deposits was greatly reduced. This reduction was supposedly due to capture of K by reactive components from the peat ash in parallel to sulphation of KCl. These compounds remained unidentified. The effect of volatile combustibles on the sulphation of gaseous KCl was investigated. The poorest sulphation was attained during injection of ammonium sulphate in the upper part of the combustion chamber during the lowest air excess ratio. The explanation for this is that SO{sub 3} was partly consumed by side reactions due to the presence of combustibles. These experimental results were supported by modelling, although the

  8. Steam reforming of acetic acid as a biomass derived oxygenate: Bifunctional pathway for hydrogen formation over Pt/ZrO2 catalysts.

    NARCIS (Netherlands)

    Takanabe, K.; Takanabe, Kazuhiro; Aika, Ken-ichi; Inazu, Koji; Baba, Toshihide; Seshan, Kulathuiyer; Lefferts, Leonardus

    2006-01-01

    Mechanistic studies on steam reforming of acetic acid over Pt/ZrO2 catalysts were performed as extension of our previous work [K. Takanabe, K. Aika, K. Seshan, L. Lefferts, J. Catal. 227 (2004) 101]. An overall picture of the bifunctional mechanism is established for steam reforming of acetic acid,

  9. Three-zonal engineering method of heat calculation for fluidized bed furnaces based on data on commercial investigations of heat generation distribution during biomass combustion

    Science.gov (United States)

    Litun, D. S.; Ryabov, G. A.

    2016-02-01

    A three-zonal method of heat calculation of furnaces for combustion of biomass and low-caloric fuel in the fluidized bed is described. The method is based on equations of thermal and material balances that account for heat generation by fuel in the zone, heat-and-mass transfer heat exchange between the furnace media and surfaces that bound the zone, and heat-and-mass transfer between furnace zones. The calculation procedure for heat generation by fuel in the fluidized bed (FB) using the heat generation portion by the fuel is proposed. Based on commercial investigations, the main factors that affect the average temperature in the FB and the portion of fuel heat that is released in the FB are determined. Results of commercial investigations showed that the airflow coefficient in the FB should be recognized as the main operation parameter that affects the average temperature in the FB and, consequently, heat generation in the FB. The gas flow rate in the FB can be marked out as the second factor that affects the consumption degree of oxidizer supplied in the FB. Commercial investigations revealed that mixing is affected by the gas flow rate in the FB and the bed material particle size, which may be changed during the boiler operation because of the agglomeration of particles of sand and ash. The calculation processing of commercial investigations on a KM-75-40M boiler of a CHP-3 of an Arkhangelsk Pulp and Paper Mill (APPM), which was carried out using the inverse problem procedure by means of a developed computer program, determined the range of the fuel heat release share in the FB, which was 0.26-0.45 at an excess air factor of 0.59-0.93 in the bed, and the heat release share in the maximum temperature zone in the total heat release in the superbed space. The heat release share in the bed is determined as an approximating function of the excess air factor in the bed and the fluidization number. The research results can be used during designing boilers with the

  10. Gas cleaning, gas conditioning and tar abatement by means of a catalytic filter candle in a biomass fluidized-bed gasifier.

    Science.gov (United States)

    Rapagnà, Sergio; Gallucci, Katia; Di Marcello, Manuela; Matt, Muriel; Nacken, Manfred; Heidenreich, Steffen; Foscolo, Pier Ugo

    2010-09-01

    A bench-scale fluidized-bed biomass gasification plant, operating at atmospheric pressure and temperature within the range 800-820 degrees C, has been used to test an innovative gas cleaning device: a catalytic filter candle fitted into the bed freeboard. This housing of the gas conditioning system within the gasifier itself results in a very compact unit and greatly reduced thermal losses. Long term (22h) tests were performed on the gasifier both with and without the catalytic candle filter, under otherwise identical conditions. Analysis of the product gas for the two cases showed the catalytic filtration to give rise to notable improvements in both gas quality and gas yield: an increase in hydrogen yield of 130% and an overall increase in gas yield of 69% - with corresponding decreases in methane and tar content of 20% and 79%, respectively. HPLC/UV analysis was used to characterize the tar compounds.

  11. Emissions of SO2,NO and N2O in a circulating fluidized bed combustor during co-firing coal and biomass

    Institute of Scientific and Technical Information of China (English)

    XIE Jian-jun; YANG Xue-min; ZHANG Lei; DING Tong-li; SONG Wen-li; LIN Wei-gang

    2007-01-01

    This paper presents the experimental investigations of the emissions of SO2, NO and N2O in a bench scale circulating fluidized bed combustor for coal combustion and co-firing coal and biomass. The thermal capacity of the combustor is 30 kW. The setup is electrically heated during startup. The influence of the excess air, the degree of the air staging, the biomass share and the feeding position of the fuels on the emissions of SO2, NO and N2O are studied. The results show that an increase in the biomass shares results in an increase of the CO concentration in the flue gas, probably due to the high volatile content of the biomass. In co-firing, the emission of SO2 increased with the increasing biomass share slightly however, non-linear increase relationship between SO2 emission and fuel sulfur content is observed. Air staging decreases the NO emission significantly without raising the SO2 level. Though change the fuel feeding position from riser to downer results in a decrease in the NO emission level, no obvious change is observed for the SO2 level. Taking the coal feeding position R as a reference, the relative NO emission can significantly decrease during co-firing coal and biomass when feeding fuel at position D and keeping the first stage stoichiometry greater than 0.95. The possible mechanisms of the sulfur and nitrogen chemistry at these conditions are discussed and the ways of simultaneous reduction of SO2, NO and N2O are proposed.

  12. Emissions of SO2, NO and N2O in a circulating fluidized bed combustor during co-firing coal and biomass.

    Science.gov (United States)

    Xie, Jian-jun; Yang, Xue-min; Zhang, Lei; Ding, Tong-li; Song, Wen-li; Lin, Wei-gang

    2007-01-01

    This paper presents the experimental investigations of the emissions of SO2, NO and N20 in a bench scale circulating fluidized bed combustor for coal combustion and co-firing coal and biomass. The thermal capacity of the combustor is 30 kW. The setup is electrically heated during startup. The influence of the excess air, the degree of the air staging, the biomass share and the feeding position of the fuels on the emissions of SO2, NO and N2O were studied. The results showed that an increase in the biomass shares resulted in an increase of the CO concentration in the flue gas, probably due to the high volatile content of the biomass. In co-firing, the emission of SO2 increased with increasing biomass share slightly, however, non-linear increase relationship between SO2 emission and fuel sulfur content was observed. Air staging significantly decreased the NO emission without raising the SO2 level. Although the change of the fuel feeding position from riser to downer resulted in a decrease in the NO emission level, no obvious change was observed for the SO2 level. Taking the coal feeding position R as a reference, the relative NO emission could significantly decrease during co-firing coal and biomass when feeding fuel at position D and keeping the first stage stoichiometry greater than 0.95. The possible mechanisms of the sulfur and nitrogen chemistry at these conditions were discussed and the ways of simultaneous reduction of SO2, NO and N20 were proposed.

  13. Technology approach to improve the amount of steam of circulating fluidized bed boiler%提高循环流化床锅炉产汽量的技术途径

    Institute of Scientific and Technical Information of China (English)

    赵代林

    2015-01-01

    循环流化床炉属于新型节能先进锅炉,我厂于1996年和2003年安装两台35t/h的循环流化床锅炉,经过几年的运行,锅炉产汽量逐渐降低,特别是煤源发生变化后,锅炉产汽量由25t/h左右降至不足15t/h。本文针对锅炉产汽量低的原因,进行了系统的研究探讨,提出了合理建议,并进行技术改造,应用于生产实际中。%Circulating fluidized bed boiler is a kind of new energy-saving boiler. There were two circulating fluidized bed boiler in our plant. After running for several years,the amount of steam deceased gradually. Especially,the amount of steam was not less than 15t/h from 25 t/h after the change of coal. Combining with this problems,the reasons were diccussed and the suggestions were put forward. The revamping measures were carried on.

  14. Molecular analysis of the biomass of a fluidized bed reactor treating synthetic vinasse at anaerobic and micro-aerobic conditions

    NARCIS (Netherlands)

    Rodriguez, E.; Lopes, A.; Fdz-Polanco, M.; Stams, A.J.M.; Garcia Encina, P.A.

    2012-01-01

    The microbial communities (Bacteria and Archaea) established in an anaerobic fluidized bed reactor used to treat synthetic vinasse (betaine, glucose, acetate, propionate, and butyrate) were characterized by denaturing gradient gel electrophoresis (DGGE) and phylogenetic analysis. This study was focu

  15. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank Farm Blend) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hall, H. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Supplemental Treatment is likely to be required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP’s LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750°C) continuous method by which LAW can be processed irrespective of whether the waste contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be comparable to LAW glass, i.e. leaches Tc-99, Re and Na at <2g/m2 during ASTM C1285 (Product Consistency) durability testing. Monolithing of the granular FBSR product was investigated to prevent dispersion during transport or burial/storage. Monolithing in an inorganic geopolymer binder, which is

  16. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank Farm Blend) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Crawford, C. L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bannochie, C. J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. R. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, W. E. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hall, H. K. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Miller, D. H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. M. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Nash, C. A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Williams, M. F. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2013-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Hanford Tank Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Supplemental Treatment is likely to be required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. The Supplemental Treatment chosen will immobilize that portion of the retrieved LAW that is not sent to the WTP’s LAW Vitrification facility into a solidified waste form. The solidified waste will then be disposed on the Hanford site in the Integrated Disposal Facility (IDF). Fluidized Bed Steam Reforming (FBSR) offers a moderate temperature (700-750°C) continuous method by which LAW can be processed irrespective of whether the waste contain organics, nitrates, sulfates/sulfides, chlorides, fluorides, volatile radionuclides or other aqueous components. The FBSR technology can process these wastes into a crystalline ceramic (mineral) waste form. The mineral waste form that is produced by co-processing waste with kaolin clay in an FBSR process has been shown to be comparable to LAW glass, i.e. leaches Tc-99, Re and Na at <2g/m2 during ASTM C1285 (Product Consistency) durability testing. Monolithing of the granular FBSR product was investigated to prevent dispersion during transport or burial/storage. Monolithing in an inorganic geopolymer binder, which is

  17. Effects of different catalysts on steam gasification of biomass char at low temperature%不同催化剂对生物质半焦低温气化效果的影响

    Institute of Scientific and Technical Information of China (English)

    俞元元; 肖军; 沈来宏; 杜玉照

    2013-01-01

    study. In which, Al2O3 was used as carrier of the catalyst, and potassium carbonate and sodium carbonate were used as active ingredient, respectively. In addition, the catalyst components were detected by X-ray diffraction analysis (XRD). Using the prepared catalysts, catalytic steam gasification of biomass char was carried out in a lab-scale fluidized bed reactor at the temperature between 600 and 700℃ ℃ to investigate the performance of catalysts. And the effects of catalyst parameters including active ingredient, ingredient contents and calcination temperature, and gasification temperature on the behavior of char gasification were also studied. The results revealed that both potassium based catalyst and sodium based one have significant catalytic action on biomass char conversion. Moreover, potassium based catalyst exhibited better catalytic performance than sodium based one with the same content of active component in rice husk char gasification process. Compared with non-catalytic rice husk char gasification, carbon conversion efficiency was increased by 18.2% and 13.5% using 30KAl(600) and 30NaAl(600), respectively. Increasing K2CO3 content was beneficial to improving char conversion efficiency, and also increasing CO and H2 yield. However the active component contents were inadvisable beyond 30%. The catalyst prepared at different calcination temperature generated the different existing forms of active components. 30KAl(800) catalyst calcinated at 800℃ showed the optimal catalytic action on the char gasification. X-ray diffraction analysis (XRD) showed that the 30KAl(800) catalyst contained K2Al2O2(CO3)2·3H2O, and thus it may be a more effective component. The results showed that both gas yield and carbon conversion efficiency of wheat straw char were higher than those of rice husk char under the same gasification conditions. Thus it also reveals that alkali metal contained in biomass ash has catalytic action on char gasification. The gas yield and carbon

  18. The formation of impurities in fluidized-bed gasification of biomass, peat and coal; Epaepuhtauksien muodostuminen leijukerroskaasutuksessa

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Laatikainen-Luntama, J.; Kurkela, M.; Leppaelahti, J.; Koljonen, T.; Oesch, P. [VTT Energy, Espoo (Finland); Alen, R. [Jyvaeskylae Univ. (Finland)

    1996-12-01

    The objective of this three-year-long project was to study the effects of different process parameters and bed materials on the formation of impurities in pressurized fluidized-bed gasification. The main emphasis of the project was focused on the formation of tars and nitrogen compounds in wood, peat and coal gasification. The aims of the research were to find out such operating conditions, where the formation of problematic high-molecular-weight tars can be minimised and to create a better understanding on the fate of fuel nitrogen in fluidized-bed gasifiers. Main part of the research was carried out in a bench-scale pressurised fluidized-bed reactor (ID 30 mm), where the effects of pressure, temperature, gas atmosphere and bed material were studied with different feedstocks. Most of the test series were carried out using the same feedstocks as earlier used in the PDU-scale fluidized-bed gasification tests of VTT (pine wood, pine bark, wheat straw, two peats, Rhenish brown coal, Polish and Illinois No.6 bituminous coals). The effects of operating parameters on the product yields (gas components, tars, char) were first studied under inert nitrogen atmosphere. The conversion of fuel nitrogen into ammonia and HCN were also determined for the different feedstocks over the different operating conditions. These studies showed that ammonia is the main fixed nitrogen compound of fluidized-bed pyrolysis with all the feedstocks studied. The conversions of fuel nitrogen into ammonia and HCN was highest with the high volatile fuels and lowest with the two hard coals. Gas atmosphere had a dramatic effect on the conversion of fuel nitrogen; much higher ammonia yields were determined in real gasification gas atmosphere than in inert pyrolysis carried out in N{sub 2} or Argon atmosphere. In addition to the pressurised fluidized-bed pyrolysis tests, laboratory scale pyrolysis research was carried out in order to compare the pyrolysis behaviour of the different feedstocks

  19. Thermal decomposition and gasification of biomass pyrolysis gases using a hot bed of waste derived pyrolysis char.

    Science.gov (United States)

    Al-Rahbi, Amal S; Onwudili, Jude A; Williams, Paul T

    2016-03-01

    Chars produced from the pyrolysis of different waste materials have been investigated in terms of their use as a catalyst for the catalytic cracking of biomass pyrolysis gases during the two-stage pyrolysis-gasification of biomass. The chars were produced from the pyrolysis of waste tyres, refused derived fuel and biomass in the form of date stones. The results showed that the hydrocarbon tar yields decreased significantly with all the char materials used in comparison to the non-char catalytic experiments. For example, at a cracking temperature of 800°C, the total product hydrocarbon tar yield decreased by 70% with tyre char, 50% with RDF char and 9% with biomass date stones char compared to that without char. There was a consequent increase in total gas yield. Analysis of the tar composition showed that the content of phenolic compounds decreased and polycyclic aromatic hydrocarbons increased in the product tar at higher char temperatures.

  20. Pilot-scale experience with biological nutrient removal and biomass yield reduction in a liquid-solid circulating fluidized bed bioreactor.

    Science.gov (United States)

    Chowdhury, Nabin; Nakhla, George; Zhu, Jesse; Islam, Mohammad

    2010-01-01

    A pilot-scale liquid-solid circulating fluidized bed (LSCFB) bioreactor was developed at the Adelaide Pollution Control Plant, London, Ontario, Canada, to study its commercial viability for biological nutrient removal. Lava rock particles of 600 microm were used as a biomass carrier media. The LSCFB removed approximately 90% organic, 80% nitrogen, and 70% phosphorus at loading rates of 4.12 kg COD/m3 x d, 0.26 kg N/m3 x d, and 0.052 kg P/m3 x d, and an empty bed contact time of 1.5 hours. Effluent characterized by < 1.0 mg NH4-N/L, < 5.0 mg NO3-N/ L, < 1.0 mg PO4-P/L, < 10 mg TN/L, < 10 mg SBOD/L, and 10 to 15 mg volatile suspended solids (VSS)/L can easily meet the criteria for nonpotable reuse of treated wastewater. The system removed nutrients without using any chemicals, and the secondary clarifier removed suspended solids removal without chemicals. A significant reduction (approximately 75%) in biomass yield to 0.12 to 0.16 g VSS/g chemical oxygen demand (COD) was observed, primarily because of long biological solids retention time (SRT) of 20 to 39 days and a combination of anoxic and aerobic COD consumption.

  1. Design, fabrication, operation and Aspen simulation of oil shale pyrolysis and biomass gasification process using a moving bed downdraft reactor

    Science.gov (United States)

    Golpour, Hassan

    Energy is the major facilitator of the modern life. Every developed and developing economy requires access to advanced sources of energy to support its growth and prosperity. Declining worldwide crude oil reserves and increasing energy needs has focused attention on developing existing unconventional fossil fuels like oil shale and renewable resources such as biomass. Sustainable, renewable and reliable resources of domestically produced biomass comparing to wind and solar energy is a sensible motivation to establish a small-scale power plant using biomass as feed to supply electricity demand and heat for rural development. The work in Paper I focuses on the possibility of water pollution from spent oil shale which should be studied before any significant commercial production is attempted. In Paper II, the proposed Aspen models for oil shale pyrolysis is to identify the key process parameters for the reactor and optimize the rate of production of syncrude from oil shale. The work in Paper III focuses on (1) Design and operation of a vertical downdraft reactor, (2) Establishing an optimum operating methodology and parameters to maximize syngas production through process testing. Finally in Paper IV, a proposed Aspen model for biomass gasification simulates a real biomass gasification system discussed in Paper III.

  2. Combustion gas from biomass - innovative plant concepts on the basis of circulating fluidized bed gasification; Brenngas aus Biomasse - innovative Anlagenkonzepte auf Basis der Zirkulierenden Wirbelschichtvergasung

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Hirschfelder, H. [Lurgi Umwelt GmbH, Frankfurt am Main (Germany)

    1998-09-01

    The contribution describes the applications of the Lurgi-ZWS gas generator. There are three main fields of application: Direct feeding of combustion gas, e.g. into a rotary kiln, as a substitute for coal or oil, without either dust filtering or gas purification. - Feeding of the combustion gas into the steam generator of a coal power plant after dust filtering and, if necessar, filtering of NH{sub 3} or H{sub 2}S. - Combustion in a gas turbine or gas engine after gas purification according to specifications. The applications are described for several exemplary projects. (orig./SR) [Deutsch] Im folgenden wird ueber die Anwendung des Lurgi-ZWS-Gaserzeugers berichtet. Nach heutiger Sicht stehen drei Anwendungsgebiete im Vordergrund: - direkte Einspeisung des Brenngases in z.B. einen Zementdrehrohrofen zur Substitution von Kohle oder Oel, ohne Entstaubung und Gasreinigung. - Einspeisung des Brenngases nach Entstaubung und gegebenenfalls Entfernung weiterer Komponenten wie NH{sub 3} oder H{sub 2}S in den Dampferzeuger eines Kohlekraftwerkes - Einsatz des Brenngases in einer Gasturbine oder Gasmotor nach spezifikationsgerechter Gasreinigung. Die aufgefuehrten Einsatzmoeglichkeiten werden am Beispiel von Projekten beschrieben. (orig./SR)

  3. Methane production from steam-exploded bamboo.

    Science.gov (United States)

    Kobayashi, Fumihisa; Take, Harumi; Asada, Chikako; Nakamura, Yoshitoshi

    2004-01-01

    To convert unutilized plant biomass into a useful energy source, methane production from bamboo was investigated using a steam explosion pretreatment. Methane could not be produced from raw bamboo but methane production was enhanced by steam explosion. The maximum amount of methane produced, i.e., about 215 ml, was obtained from 1 g of exploded bamboo at a steam pressure of 3.53 MPa and a steaming time of 5 min. A negative correlation between the amount of methane produced and the amount of Klason lignin was observed in the methane fermentation of steam-exploded bamboo.

  4. Biomass gasification and energy production

    Energy Technology Data Exchange (ETDEWEB)

    Mahinpey, N.; Nikoo, M.B. [Regina Univ., SK (Canada). Faculty of Engineering

    2007-07-01

    The ASPEN PLUS simulation program was used to model an atmospheric fluidized bed biomass gasifier. The aim of the study was develop a simulation capable of accurately predicting steady state performance of the gasifier in relation to hydrodynamics and reaction kinetics. The influences of feed decomposition, volatile reactions, gas gasification and gas-solid separation were considered through modularized ASPEN PLUS models. The ASPEN PLUS yield reactor was used to simulate biomass feed decomposition. A separation column model was used to separate volatile materials and solids. Experimental data from a pine biomass gasification experiment conducted in a laboratory-scale fluidized bed gasifier was used to validate the simulation results. Good agreement was shown for gas composition, although carbon dioxide (CO{sub 2}) rates were slightly underestimated. The study also demonstrated that higher temperatures improved the gasification process and carbon conversion. The optimized gasification process produced more carbon monoxide (CO) and less CO{sub 2}. The introduction of lower temperature steam to the gasification process increased tar output. It was concluded that the conversion efficiency increased when the equivalence ratio was increased. 7 refs., 1 tab., 12 figs.

  5. Preparation of Hydrogen through Catalytic Steam Reforming of Bio-oil

    Institute of Scientific and Technical Information of China (English)

    吴层; 颜涌捷; 李庭琛; 亓伟

    2007-01-01

    Hydrogen was prepared via catalytic steam reforming of bio-oil which was obtained from fast pyrolysis of biomass in a fluidized bed reactor. Influential factors including temperature, weight hourly space velocity (WHSV) of bio-oil, mass ratio of steam to bio-oil (S/B) as well as catalyst type on hydrogen selectivity and other desirable gas products were investigated. Based on hydrogen in stoichiometric potential and carbon balance in gaseous phase and feed, hydrogen yield and carbon selectivity were examined. The experimental results show that higher temperature favors the hydrogen selectivity by H2 mole fraction in gaseous products stream and it plays an important role in hydrogen yield and carbon selectivity. Higher hydrogen selectivity and yield, and carbon selectivity were obtained at lower bio-oil WHSV. In catalytic steam reforming system a maximum steam concentration value exists, at which hydrogen selectivity and yield, and carbon selectivity keep constant. Through experiments, preferential operation conditions were obtained as follows: temperature 800~850℃, bio-oil WHSV below 3.0 h-1, and mass ratio of steam to bio-oil 10~12. The performance tests indicate that Ni-based catalysts are optional, especially Ni/a-Al2O3 effective in the steam reforming process.

  6. Allothermal gasification of biomass using micron size biomass as external heat source.

    Science.gov (United States)

    Cheng, Gong; Li, Qian; Qi, Fangjie; Xiao, Bo; Liu, Shiming; Hu, Zhiquan; He, Piwen

    2012-03-01

    An allothermal biomass gasification system using biomass micron fuel (BMF) as external heat source was developed. In this system, heat supplied to gasifier was generated from combustion of BMF. Biomass feedstock was gasified with steam and then tar in the produced gas was decomposed in a catalytic bed with NiO/γ-Al(2)O(3) catalyst. Finally the production gas was employed as a substitute for civil fuel gas. An overall energy analysis of the system was also investigated. The results showed that the lower heating value of the product gas reached more than 12 MJ/Nm(3). The combusted BMF accounted for 26.8% of the total energy input. Allothermal gasification based on the substituted BMF for conventional energy was an efficient and economical technology to obtain bioenergy.

  7. Co-gasification of biosolids with biomass: Thermogravimetric analysis and pilot scale study in a bubbling fluidized bed reactor.

    Science.gov (United States)

    Yu, Ming Ming; Masnadi, Mohammad S; Grace, John R; Bi, Xiaotao T; Lim, C Jim; Li, Yonghua

    2015-01-01

    This work studied the feasibility of co-gasification of biosolids with biomass as a means of disposal with energy recovery. The kinetics study at 800°C showed that biomass, such as switchgrass, could catalyze the reactions because switchgrass ash contained a high proportion of potassium, an excellent catalyst for gasification. However, biosolids could also inhibit gasification due to interaction between biomass alkali/alkaline earth metals and biosolids clay minerals. In the pilot scale experiments, increasing the proportion of biosolids in the feedstock affected gasification performance negatively. Syngas yield and char conversion decreased from 1.38 to 0.47m(3)/kg and 82-36% respectively as the biosolids proportion in the fuel increased from 0% to 100%. Over the same range, the tar content increased from 10.3 to 200g/m(3), while the ammonia concentration increased from 1660 to 19,200ppmv. No more than 25% biosolids in the fuel feed is recommended to maintain a reasonable gasification.

  8. Hydrogen Production From Crude Bio-oil and Biomass Char by Electrochemical Catalytic Reforming

    Institute of Scientific and Technical Information of China (English)

    Xing-long Li; Shen Ning; Li-xia Yuan; Quan-xin Li

    2011-01-01

    We reports an efficient approach for production of hydrogen from crude bio-oil and biomass char in the dual fixed-bed system by using the electrochemical catalytic reforming method.The maximal absolute hydrogen yield reached 110.9 g H2/kg dry biomass.The product gas was a mixed gas containing 72%H2,26%CO2,1.9%CO,and a trace amount of CH4.It was observed that adding biomass char (a by-product of pyrolysis of biomass) could remarkably increase the absolute H2 yield (about 20%-50%).The higher reforming temperature could enhance the steam reforming reaction of organic compounds in crude bio-oil and the reaction of CO and H2O.In addition,the CuZn-Al2O3 catalyst in the water-gas shift bed could also increase the absolute H2 yield via shifting CO to CO2.

  9. Hydrogen Production From Crude Bio-oil and Biomass Char by Electrochemical Catalytic Reforming

    Science.gov (United States)

    Li, Xing-long; Ning, Shen; Yuan, Li-xia; Li, Quan-xin

    2011-08-01

    We reports an efficient approach for production of hydrogen from crude bio-oil and biomass char in the dual fixed-bed system by using the electrochemical catalytic reforming method. The maximal absolute hydrogen yield reached 110.9 g H2/kg dry biomass. The product gas was a mixed gas containing 72%H2, 26%CO2, 1.9%CO, and a trace amount of CH4. It was observed that adding biomass char (a by-product of pyrolysis of biomass) could remarkably increase the absolute H2 yield (about 20%-50%). The higher reforming temperature could enhance the steam reforming reaction of organic compounds in crude bio-oil and the reaction of CO and H2O. In addition, the CuZn-Al2O3 catalyst in the water-gas shift bed could also increase the absolute H2 yield via shifting CO to CO2.

  10. Fluidized-bed gasification of biomass: Conversion of fine carabon particles in the freeboard; Biomassevergasung in der Wirbelschicht: Umsatz von feinen Kohlenstoffpartikeln im Freeboard

    Energy Technology Data Exchange (ETDEWEB)

    Miccio, F. [Ist. Ricerche sulla Combustione-CNR, Napoli (Italy); Moersch, O.; Spliethoff, H.; Hein, K.R.G. [Stuttgart Univ. (Germany). Inst. fuer Verfahrenstechnik und Dampfkesselwesen

    1998-09-01

    The conversion of carbon particles in gasification processes was investigated in a fluidized-bed reactor of the Institute of Chemical Engineering and Steam Boiler Technology of Stuttgart University. This reactor is heated electrically to process temperature, and freeboard coal particles can be sampled using an isokinetic probe. The fuel used in the experiments consisted of beech wood chips. The temperature and air rating, i.e. the main parameters of the process, were varied in order to investigate their influence on product gas quality and carbon conversion. The conversion rate is influenced to a significant extent by grain disintegration and discharge of carbon particles. In gasification conditions, a further conversion process takes place in the freeboard. (orig.) [Deutsch] In dieser Arbeit wird die Umsetzung von Kohlenstoffpartikeln unter Vergasungsbedingungen untersucht. Die Versuche wurden an einem Wirbelschichtreaktor des Instituts fuer Verfahrenstechnik und Dampfkesselwesen der Universitaet Stuttgart durchgefuehrt. Dieser Reaktor wird elektrisch auf Prozesstemperatur beheizt. Mit Hilfe einer isokinetischen Sonde koennen Proben von Kohlenstoffpartikeln im Freeboard genommen werden. Als Brennstoff wurden zerkleinerte Buchenholz-Hackschnitzel eingesetzt. Variiert wurden als Hauptparameter des Prozesses Temperatur und Luftzahl. Untersucht wurde der Einfluss dieser Parameter auf die Qualitaet des Produktgases und die Umsetzung des Kohlenstoffes. Kornzersetzungs- und Austragsvorgaenge von Kohlenstoffpartikeln spielen eine wichtige Rolle fuer den Kohlenstoffumsatz. Unter Vergasungsbedingungen findet im Freeboard eine weitere Umsetzung der Partikel statt. (orig.)

  11. Study on solidification and stabilization technique by steam treatment of the coal ash from fluidized-bed combustion boilers; Ryudoso sekitanbai no joki shori ni yoru koka / anteika gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shibata, Y. [Kawasaki Heavy Industries Ltd., Kobe (Japan)

    1998-08-20

    In fluidized-bed coal combustion boiler supporting one end of boilers for power generation and process heating, coal ash comprised of the products of ash of coal and lime stone used for desulfurizer was used for raw material. The fluidized-bed combustion boiler really working at present is of normal pressure (AFBC) type due to bubbling or cycling system, and pressure type of the bubbling system (PFBC) due to high pressure of about 1.0 MPa is promoted development for a next generation type power generation. Then, by using the coal ash obtained from the AFBC boiler with different kind of coal, volume of boiler, and so on (AFBC ash) and the coal ash obtained from the PFBC boiler under actual proof operation, a study on properties of coal, lime stone and solids after steam treatment of mixture with water (kind/volume, strength and elution of hazard heavy metals of hydrates) were conducted to investigate to use for civil engineering materials such as road materials, filling back materials, and so forth. 16 refs., 13 figs., 2 tabs.

  12. Anammox enrichment from reject water on blank biofilm carriers and carriers containing nitrifying biomass: operation of two moving bed biofilm reactors (MBBR).

    Science.gov (United States)

    Zekker, Ivar; Rikmann, Ergo; Tenno, Toomas; Lemmiksoo, Vallo; Menert, Anne; Loorits, Liis; Vabamäe, Priit; Tomingas, Martin; Tenno, Taavo

    2012-07-01

    The anammox bacteria were enriched from reject water of anaerobic digestion of municipal wastewater sludge onto moving bed biofilm reactor (MBBR) system carriers-the ones initially containing no biomass (MBBR1) as well as the ones containing nitrifying biomass (MBBR2). Duration of start-up periods of the both reactors was similar (about 100 days), but stable total nitrogen (TN) removal efficiency occurred earlier in the system containing nitrifying biomass. Anammox TN removal efficiency of 70% was achieved by 180 days in both 20 l volume reactors at moderate temperature of 26.0°C. During the steady state phase of operation of MBBRs the average TN removal efficiencies and maximum TN removal rates in MBBR1 were 80% (1,000 g-N/m(3)/day, achieved by 308 days) and in MBBR2 85% (1,100 g-N/m(3)/day, achieved by 266 days). In both reactors mixed bacterial cultures were detected. Uncultured Planctomycetales bacterium clone P4, Candidatus Nitrospira defluvii and uncultured Nitrospira sp. clone 53 were identified by PCR-DGGE from the system initially containing blank biofilm carriers as well as from the nitrifying biofilm system; from the latter in addition to these also uncultured ammonium oxidizing bacterium clone W1 and Nitrospira sp. clone S1-62 were detected. FISH analysis revealed that anammox microorganisms were located in clusters in the biofilm. Using previously grown nitrifying biofilm matrix for anammox enrichment has some benefits over starting up the process from zero, such as less time for enrichment and protection against severe inhibitions in case of high substrate loading rates.

  13. 利用高温铜渣余热进行生物质水蒸气汽化的热力学分析%Thermodynamic Analysis on Biomass Steam Gasification Using High-temperature Copper Slag Waste Heat

    Institute of Scientific and Technical Information of China (English)

    李娟琴; 胡建杭; 王华; 邓双辉; 胡威

    2013-01-01

    基于平衡常数法建立生物质水蒸气汽化的热力学平衡模型.模型计算结果表明:生物质水蒸气汽化产气组分趋于稳定的汽化条件为845~950℃、S/B(水蒸气质量与生物质质量之比)为1.5~2.0(g/g),900℃、S/B为1.64时合成气(CO+H2)产量最高,为73.15%.利用高温铜渣显热作为生物质水蒸气汽化吸热反应的外热源,计算不同汽化温度下铜渣的热焓和余热利用率.计算结果表明:汽化温度在720~950℃范围内,铜渣余热利用率为25.28%~60.04%;最优汽化工况下,铜渣余热利用率为31.66%,系统能量转化率高达48%.%A thermodynamic equilibrium model of biomass steam gasification was established based on equilibrium constant method. The calculated results show that biomass steam gasification gas are stable for 845 — 950℃ and S/B of 1. 5-2. 0(g/g) and the highest syngas (CO+ H2) yield is 73. 15% for 900 °C and S/B= 1. 64 . It was calculated that enthalpy of copper slag and sensible heat utilization efficiency of copper slag on different gasification temperature using the sensible heat of high temperature copper slag as the heat source of biomass steam gasification. The calculated results show that waste heat utilization efficiency of copper slag is 25. 28%—60. 04% within the gasification temperature range of 720 — 950 ℃ and waste heat utilization efficiency of copper slag is 31. 66% and system energy efficiency is 48% on optimal condition.

  14. Olivine, dolomite and ceramic filters in one vessel to produce clean gas from biomass.

    Science.gov (United States)

    Rapagnà, Sergio; Gallucci, Katia; Foscolo, Pier Ugo

    2017-07-27

    Heavy organic compounds produced during almond shells gasification in a steam and/or air atmosphere, usually called tar, are drastically reduced in the product gas by using simultaneously in one vessel a ceramic filter placed in the freeboard and a mixture of olivine and dolomite particles in the fluidized bed of the gasifier. The content of tar in the product gas during a reference gasification test with air, in presence of fresh olivine particles only, was 8600mg/Nm(3) of dry gas. By gasifying biomass with steam at the same temperature level of 820°C in a bed of olivine and dolomite (20% by weight), and in the presence of a catalytic ceramic filter inserted in the freeboard of the fluidized bed gasifier, the level of tar was brought down to 57mg/Nm(3) of dry producct gas, with a decrease of more than two orders of magnitude. Copyright © 2017. Published by Elsevier Ltd.

  15. Biomass fast pyrolysis for bio-oil production in a fluidized bed reactor under hot flue atmosphere.

    Science.gov (United States)

    Li, Ning; Wang, Xiang; Bai, Xueyuan; Li, Zhihe; Zhang, Ying

    2015-10-01

    Fast pyrolysis experiments of corn stalk were performed to investigate the optimal pyrolysis conditions of temperature and bed material for maximum bio-oil production under flue gas atmosphere. Under the optimized pyrolysis conditions, furfural residue, xylose residue and kelp seaweed were pyrolyzed to examine their yield distributions of products, and the physical characteristics of bio-oil were studied. The best flow rate of the flue gas at selected temperature is obtained, and the pyrolysis temperature at 500 degrees C and dolomite as bed material could give a maximum bio-oil yield. The highest bio-oil yield of 43.3% (W/W) was achieved from corn stalk under the optimal conditions. Two main fractions were recovered from the stratified bio-oils: light oils and heavy oils. The physical properties of heavy oils from all feedstocks varied little. The calorific values of heavy oils were much higher than that of light oils. The pyrolysis gas could be used as a gaseous fuel due to a relatively high calorific value of 6.5-8.5 MJ/m3.

  16. Biomass gasification for energy production

    Energy Technology Data Exchange (ETDEWEB)

    Lundberg, H.; Morris, M.; Rensfelt, E. [TPS Termiska Prosesser Ab, Nykoeping (Sweden)

    1997-12-31

    Biomass and waste are becoming increasingly interesting as fuels for efficient and environmentally sound power generation. Circulating fluidized bed (CFB) gasification for biomass and waste has been developed and applied to kilns both in the pulp and paper industry and the cement industry. A demonstration plant in Greve-in- Chianti, Italy includes two 15 MW{sub t}h RDF-fuelled CFB gasifiers of TPS design, the product gas from which is used in a cement kiln or in steam boiler for power generation. For CFB gasification of biomass and waste to reach a wider market, the product gas has to be cleaned effectively so that higher fuel to power efficiencies can be achieved by utilizing power cycles based on engines or gas turbines. TPS has developed both CFB gasification technology and effective secondary stage tar cracking technology. The integrated gasification - gas-cleaning technology is demonstrated today at pilot plant scale. To commercialise the technology, the TPS`s strategy is to first demonstrate the process for relatively clean fuels such as woody biomass and then extend the application to residues from waste recycling. Several demonstration projects are underway to commercialise TPS`s gasification and gas cleaning technology. In UK the ARBRE project developed by ARBRE Energy will construct a gasification plant at Eggborough, North Yorkshire, which will provide gas to a gas turbine and steam turbine generation system, producing 10 MW and exporting 8 Mw of electricity. It has been included in the 1993 tranche of the UK`s Non Fossil Fuel Obligation (NFFO) and has gained financial support from EC`s THERMIE programme as a targeted BIGCC project. (author)

  17. Effect of Degradation Compounds from Steam Explosion Pretreatment of Popular Biomass on Kluyveromyces marxianus; Efecto de los productos de degradacion originados en la explosion por vapor de biomasa de chopo sobre Kluyveromyces marxianus

    Energy Technology Data Exchange (ETDEWEB)

    Oliva Dominguez, J. M.

    2003-07-01

    The Simultaneous Saccharificationa and Fermentation (SSF) process has been suggested as one of the most promising methods to obtain ethanol from lignocellulose. This SSF process requires a previous pretreatment step in order to increase accessibility of cellulose to enzymatic hydrolysis. Auto hydrolysis steam explosion pretreatment has been recognised as a cost-effective method for p retreating lignocellulosic biomass. During the steam explosion pretreatment of lignocellulose substrates various toxic compounds, that could inhibit microbial fermentation, are formed. These inhibitor compounds belong to three major groups: weak acids, furans and phenolic compounds. In this study, the filtrate from steam-pretreated poplar was analysed to identify degradation compounds. The effect of identified compounds on growth and ethanol production by Kluyveromyces marxianus CECT 10875 was tested in experiments where those compounds were added individually or in combination to a synthetic medium. The level of inhibition on yeast strain growth and ethanolic fermentation was determined. The effect of initial pH on toxicity of organic acids and assimilation of these compounds by the yeast was also studied. At concentrations found in the pre hydrolysate none of individual compounds significantly effect the fermentation. For all tested compounds ethanol production was inhibited to a lesser extent than growth. Finally, different detoxification methods were applied to the liquid fraction in order to use it as fermentation broth. the detoxification methods included: treatment with alkali (sodium hydroxide or calcium hydroxide), evaporation (25%, 50% or 75% of the initial volume), advanced oxidation process (Fenton's reaction) and detoxification with zeolites. The changes in the concentration of toxic compounds were determined and the fermentability of the detoxified liquid fraction was assayed after applying those detoxification methods. (Author)

  18. Development of pressurised fluidised bed combustion technique for coal-fired gas/steam processes; Entwicklung der Druckwirbelschicht-Feuerungstechnik fuer kohlegefeuerte Gas-Dampfprozesse

    Energy Technology Data Exchange (ETDEWEB)

    Pitt, R.; Steven, H.

    1992-12-31

    The investigations for the development of the pressurized fluidized bed technique have shown that it is possible, in principle, to keep within the emission limits with the steady state pressurised fluidised bed combustion, even at low part load. However, the construction expense is considerable and the type of coal and grain size must comply relatively exactly with the design values. Not every fuel is suitable for fluidised bed combustion regarding emission. The most important parameter for emission is the temperature profile for this component, which should be as even as possible at a high temperature level. A sufficient dwell time of the gas and the particles is decisive for CO emission, where a minimum reaction time is required for both phases. (orig.) [Deutsch] Die Untersuchungen zur Entwicklung der Druckwirbelschichttechnik haben gezeigt, dass es prinzipiell moeglich ist, mit der stationaeren druckaufgeladenen Wirbelschichtfeuerung die Emissionsgrenzwerte auch bei geringer Teillast einzuhalten, allerdings ist der bauliche Aufwand erheblich und auch die Kohleart und Koernung muessen relativ genau den Auslegungswerten entsprechen. Auch hinsichtlich der Emissionen ist nicht jeder Brennstoff fuer die Wirbelschichtfeuerung geeignet. Wichtigster Einflusspartner auf die Emission ist auch bei dieser Komponente das Temperaturprofil, das moeglichst gleichmaessig auf hohem Temperaturniveau liegen sollte. Ausreichende Verweilzeit des Gases und der Partikel sind fuer die CO-Emission entscheidend, wobei fuer beide Phasen eine Mindestreaktionszeit erforderlich ist. (orig.)

  19. Design and Performance Experiments of Biomass Briquette Chain Steam Boiler%生物质成型燃料链条蒸汽锅炉的设计和性能试验

    Institute of Scientific and Technical Information of China (English)

    王鹏晓; 刘圣勇; 夏许宁; 翟万里; 管泽运; 刘霞

    2016-01-01

    根据生物质成型燃料挥发分含量高、固定碳含量低和灰渣熔融性强的特点,设计了工作压力1.25 MPa、额定出口蒸汽温度194℃的链条蒸汽锅炉.该锅炉拥有独特的多拱炉膛结构和二次风配风系统,实现生物质成型燃料的气相多段燃烧和固相低强度燃烧,提高燃烧稳定性.试验表明:该锅炉的热效率达82.79%,烟气中颗粒物、二氧化硫、氮氧化物等污染物排放浓度均低于锅炉大气污染物排放标准的限值,锅炉具有良好的热效率和环保效益.%According to high volatile content,low fixed carbon content and low ash melting of biomass briquette, the chain-steam boiler with working pressure of 1.25 MPa and rated outlet steam temperature of 194℃is designed. This boiler has special multi-arch furnace structure and air distribution systems,which achieves biomass briquette's gas multi-segment combustion and the low intensity combustion of solid phase,improving combustion stability. The test results show that thermal efficiency of the boiler reaches to 82.79%,and the pollutant emission concentration of flue gas is lower than the boiler air pollutant emission standards limits. The boiler has a good thermal efficiency and environmental benefits.

  20. Biomass gasification for liquid fuel production

    Science.gov (United States)

    Najser, Jan; Peer, Václav; Vantuch, Martin

    2014-08-01

    In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they dońt compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis.

  1. Biomass gasification for liquid fuel production

    Energy Technology Data Exchange (ETDEWEB)

    Najser, Jan, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz; Peer, Václav, E-mail: jan.najser@vsb.cz, E-mail: vaclav.peer@vsb.cz [VSB - Technical university of Ostrava, Energy Research Center, 17. listopadu 15/2172, 708 33 Ostrava-Poruba (Czech Republic); Vantuch, Martin [University of Zilina, Faculty of Mechanical Engineering, Department of Power Engineering, Univerzitna 1, 010 26 Zilina (Slovakia)

    2014-08-06

    In our old fix-bed autothermal gasifier we tested wood chips and wood pellets. We make experiments for Czech company producing agro pellets - pellets made from agricultural waste and fastrenewable natural resources. We tested pellets from wheat and rice straw and hay. These materials can be very perspective, because they dońt compete with food production, they were formed in sufficient quantity and in the place of their treatment. New installation is composed of allothermal biomass fixed bed gasifier with conditioning and using produced syngas for Fischer - Tropsch synthesis. As a gasifying agent will be used steam. Gas purification will have two parts - separation of dust particles using a hot filter and dolomite reactor for decomposition of tars. In next steps, gas will be cooled, compressed and removed of sulphur and chlorine compounds and carbon dioxide. This syngas will be used for liquid fuel synthesis.

  2. FLUIDIZED BED STEAM REFORMING (FBSR) OF HIGH LEVEL WASTE (HLW) ORGANIC AND NITRATE DESTRUCTION PRIOR TO VITRIFICATION: CRUCIBLE SCALE TO ENGINEERING SCALE DEMONSTRATIONS AND NON-RADIOACTIVE TO RADIOACTIVE DEMONSTRATIONS

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C; Michael Williams, M; Gene Daniel, G; Paul Burket, P; Charles Crawford, C

    2009-02-07

    Over a decade ago, an in-tank precipitation process to remove Cs-137 from radioactive high level waste (HLW) supernates was demonstrated at the Savannah River Site (SRS). The full scale demonstration with actual HLW was performed in SRS Tank 48 (T48). Sodium tetraphenylborate (NaTPB) was added to enable Cs-137 extraction as CsTPB. The CsTPB, an organic, and its decomposition products proved to be problematic for subsequent processing of the Cs-137 precipitate in the SRS HLW vitrification facility for ultimate disposal in a HLW repository. Fluidized Bed Steam Reforming (FBSR) is being considered as a technology for destroying the organics and nitrates in the T48 waste to render it compatible with subsequent HLW vitrification. During FBSR processing the T48 waste is converted into organic-free and nitrate-free carbonate-based minerals which are water soluble. The soluble nature of the carbonate-based minerals allows them to be dissolved and pumped to the vitrification facility or returned to the tank farm for future vitrification. The initial use of the FBSR process for T48 waste was demonstrated with simulated waste in 2003 at the Savannah River National Laboratory (SRNL) using a specially designed sealed crucible test that reproduces the FBSR pyrolysis reactions, i.e. carbonate formation, organic and nitrate destruction. This was followed by pilot scale testing of simulants at the Science Applications International Corporation (SAIC) Science & Technology Application Research (STAR) Center in Idaho Falls, ID by Idaho National Laboratory (INL) and SRNL in 2003-4 and then engineering scale demonstrations by THOR{reg_sign} Treatment Technologies (TTT) and SRS/SRNL at the Hazen Research, Inc. (HRI) test facility in Golden, CO in 2006 and 2008. Radioactive sealed crucible testing with real T48 waste was performed at SRNL in 2008, and radioactive Benchscale Steam Reformer (BSR) testing was performed in the SRNL Shielded Cell Facility (SCF) in 2008.

  3. Biomass integrated CFB gasification combined cycle plants

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Hirschfelder, H. (Lurgi Umwelt GmbH, Frankfurt am Main (Germany))

    1998-01-01

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste or coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi's CFB gasification technology is at present applied in two industrial plants. It is the key process for the advanced biomass or waste utilisation plants. The paper focuses on CFB fuel gas production for combined cycle plants (IGCC) and for cofiring into existing boiler plants. 5 refs., 4 figs.

  4. Fuel gas from biomass - utilisation concepts

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Vierrath, H. [Lurgi Envirotherm GmbH, Frankfurt am Main (Germany)

    2000-07-01

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste of coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi's CFB gasification technology is at present applied in two industrial plants. It is the key process for our advanced biomass or waste utilisation plants. The subject paper will focus on CFB fuel gas production for combined cycle plants (IGCC) and for co-firing into existing boiler plants. (orig.)

  5. Biomass integrated CFB gasification combined cycle plants

    Energy Technology Data Exchange (ETDEWEB)

    Greil, C.; Hirschfelder, H. [Lurgi Umwelt GmbH, Frankfurt am Main (Germany)

    1998-12-31

    This paper presents an overview on the Lurgi-Circulating Fluidized Bed technology (CFB). CFB units are state of the art and have proven their capability of converting biomass, waste or coal into power and/or steam. CFB reactors are in commercial operation for reduction processes and for combustion and gasification of solid fuels. In this paper reduction processes are not considered. The fact, that world-wide over 80 CFB combustion plants using Lurgi technology are commercially operating proves that this technology is well accepted. Lurgi`s CFB gasification technology is at present applied in two industrial plants. It is the key process for the advanced biomass or waste utilisation plants. The paper focuses on CFB fuel gas production for combined cycle plants (IGCC) and for cofiring into existing boiler plants. 5 refs., 4 figs.

  6. Progress toward Biomass and Coal-Derived Syngas Warm Cleanup: Proof-of-Concept Process Demonstration of Multicontaminant Removal for Biomass Application

    Energy Technology Data Exchange (ETDEWEB)

    Howard, Christopher J.; Dagle, Robert A.; Lebarbier, Vanessa MC; Rainbolt, James E.; Li, Liyu; King, David L.

    2013-06-19

    Systems comprising of multiple sorbent and catalytic beds have been developed for the warm syngas cleanup of coal- and biomass-derived syngas. Tailored specifically for biomass application the process described here consists of six primary unit operations: 1) Na2CO3 bed for HCl removal, 2) two regenerable ZnO beds for bulk H2S removal, 3) ZnO bed for H2S polishing, 4) NiCu/SBA-16 sorbent for trace metal (e.g. AsH3) removal, 5) steam reforming catalyst bed for tars and light hydrocarbons reformation and NH3 decomposition, and a 6) Cu-based LT-WGS catalyst bed. Simulated biomass-derived syngas containing a multitude of inorganic contaminants (H2S, AsH3, HCl, and NH3) and hydrocarbon additives (methane, ethylene, benzene, and naphthalene) was used to demonstrate process effectiveness. The efficiency of the process was demonstrated for a period of 175 hours, during which no signs of deactivation were observed. Post-run analysis revealed small levels of sulfur slipped through the sorbent bed train to the two downstream catalytic beds. Future improvements could be made to the trace metal polishing sorbent to ensure complete inorganic contaminant removal (to low ppb level) prior to the catalytic steps. However, dual, regenerating ZnO beds were effective for continuous removal for the vast majority of the sulfur present in the feed gas. The process was effective for complete AsH3 and HCl removal. The steam reforming catalyst completely reformed all the hydrocarbons present in the feed (methane, ethylene, benzene, and naphthalene) to additional syngas. However, post-run evaluation, under kinetically-controlled conditions, indicates deactivation of the steam reforming catalyst. Spent material characterization suggests this is attributed, in part, to coke formation, likely due to the presence of benzene and/or naphthalene in the feed. Future adaptation of this technology may require dual, regenerable steam reformers. The process and materials described in this report hold

  7. Steam Turbines

    Science.gov (United States)

    1981-01-01

    Turbonetics Energy, Inc.'s steam turbines are used as power generating systems in the oil and gas, chemical, pharmaceuticals, metals and mining, and pulp and paper industries. The Turbonetics line benefited from use of NASA research data on radial inflow steam turbines and from company contact with personnel of Lewis Research Center, also use of Lewis-developed computer programs to determine performance characteristics of turbines.

  8. 生物质氧气气化和水蒸汽气化的能量分析及(火用)分析%Energy and exergy analysis of biomass gasification with oxygen or steam

    Institute of Scientific and Technical Information of China (English)

    张亚宁; 李炳熙; 张波; 李洪涛

    2012-01-01

    Based on the experiments data of a reference where sawdust gasified with oxygen or steam at 800 ℃ , 900 ℃ , 1 000 ℃ , 1 100 ℃ and 1 200 ℃. , respectively, the energy value, exergy value, energy efficiency and exergy efficency of product gas were studied in this paper. The results show that the energy value, exergy value, energy efficiency and exergy efficency of product gas from biomass oxygen gasifcation are 9 433.49 ~ 12 972. 63 kJ ? Kg-1 , 8 382. 97~11 166. 42 kJ ? Kg-1, 40. 30 ~49. 77% and 34. 76 - 42. 21 % , respectively. The energy value, exergy value, energy efficiency and exergy efficency of product gas from biomass steam gasificaon are 14 323.61 ~ 19 608. 99 kJ ? Kg-1, 12 814. 82 - 16 400. 45 KJ ? Kg-1, 54. 70 ~ 66. 28% and 47. 58 - 56. 04% , respectively. Steam gasification generates higher energy value, exergy value, energy efficiency and exergy efficency than oxygen gasifcation, thereby showing a better gasification technology.%基于文献数据,研究了木屑在800℃,900℃,1 000℃,1 100℃和1 200℃时氧气气化和水蒸汽气化所产气化气的能值、(火用)值、能量效率和(火用)效率,结果表明:氧气气化所得气化气体的能值、(火用)值、能量效率和(火用)效率分别为9 433.49 ~ 12 972.63 kJ·kg -,8 382.97~11 166.42 kJ·kg -,40.30~49.77%和34.76 ~42.21%;水蒸汽气化所得气化气体的能值、(火用)值、能量效率和(火用)效率分别为14 323.61 ~19 608.99kJ·kg -1,12 814.82~16 400.45 kJ·kg-1,54.70 ~66.28%和47.58 ~56.04%.水蒸汽气化所得气化气体呈现出较高的能值、(火用)值、能量效率和(火用)效率,从而表现为一种更好的气化方式.

  9. Fast pyrolysis of biomass in fluidized bed reactor UNICAMP, Brazil: problems, causes and solutions; Pirolise rapida de biomassa em reator de leito fluidizado UNICAMP-Brasil: problemas, causas e solucoes

    Energy Technology Data Exchange (ETDEWEB)

    Mesa Perez, Juan Miguel; Marin Mesa, Henry Ramon [Bioware Tecnologia, Campinas, SP (Brazil); Rocha, Jose Dilcio; Olivares Gomez, Edgardo [Universidade Estadual de Campinas (NIPE/UNICAMP), SP (Brazil). Nucleo Interdisciplinar de Planejamento Energetico; Cortez, Luis Augusto Barbosa; Shimabukuro, Fabio Rodrigo; Vallin, Marco Jim Gui [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola

    2006-07-01

    The fluidized bed reactor developed by the researchers of the UNICAMP in the installations of the Sugar Cane Technology Center (CTC), in Piracicaba-SP, is the first reactor of biomass fast pyrolysis in Brazil to produce bio-oil. In this work the problems of operation with the reactor in functioning are presented as the emptying of gases produced in the pyrolysis by means of the biomass feeding system, the block of the thread of biomass feeding, the inert material sintering in the bed, etc. The possible causes are described. Thus it, the first ones could be solved, either by the reduction of the height of the inert bed, or by the increase of the wadding percentage of the thread, among others. These results of the exploratory tests make possible the steady work of the plant, greater knowledge of the phenomena that occur during the fast pyrolysis in flutizide bed, as well as the establishment of adjusted levels for the identified independent factors during the remaining experimental works. (author)

  10. Combustion of biomass-derived, low caloric value, fuel gas in a gasturbine combustor

    Energy Technology Data Exchange (ETDEWEB)

    Andries, J.; Hoppesteyn, P.D.J.; Hein, K.R.G. [Technische Univ. Delf (Netherlands)

    1998-09-01

    The use of biomass and biomass/coal mixtures to produce electricity and heat reduces the net emissions of CO{sub 2}, contributes to the restructuring of the agricultural sector, helps to reduce the waste problem and saves finite fossil fuel reserves. Pressurised fluidised bed gasification followed by an adequate gas cleaning system, a gas turbine and a steam turbine, is a potential attractive way to convert biomass and biomass/coal mixtures. To develop and validate mathematical models, which can be used to design and operate Biomass-fired Integrated Gasification Combined Cycle (BIGCC) systems, a Process Development Unit (PPDU) with a maximum thermal capacity of 1.5 MW{sub th}, located at the Laboratory for Thermal Power Engineering of the Delft University of Technology in The Netherlands is being used. The combustor forms an integral part of this facility. Recirculated flue gas is used to cool the wall of the combustor. (orig.)

  11. Catalytic gasification of oil-extracted residue biomass of Botryococcus braunii.

    Science.gov (United States)

    Watanabe, Hideo; Li, Dalin; Nakagawa, Yoshinao; Tomishige, Keiichi; Watanabe, Makoto M

    2015-09-01

    Catalytic gasification of the oil-extracted residue biomass of Botryococcus braunii was demonstrated in a laboratory-scale continuous feeding dual bed reactor. Steam gasification at 1023 K over Ni-Fe/Mg/Al catalyst can completely reform tar derived from pyrolysis of the residue biomass into C1 gases and hydrogen, and has achieved 91%-C conversion to gaseous product (CO+CO2+CH4). Composition of product gas has higher contents of CO and H2 with their ratio (H2/CO) of around 2.4 which is slightly H2-rich syngas. Maximum hydrogen yield of 74.7 mmol g-biomass(-1) obtained in this work is much higher than that from gasification of other algal biomass reported in literature. The residue biomass of B. braunii can be a superior renewable source of syngas or hydrogen. Copyright © 2015 Elsevier Ltd. All rights reserved.

  12. Fundamental studies of synthesis-gas production based on fluidised-bed gasification of biomass-UCGFunda

    Energy Technology Data Exchange (ETDEWEB)

    Reinikainen, M.; Moilanen, A.; Simell, P.; Hannula, I.; Kurkela, E. (VTT Technical Research Centre of Finland, Espoo (Finland)), e-mail: matti.reinikainen@vtt.fi; Suominen, T. P. (Aabo Akademi, Turku (Finland), Teknisk Kemi och Reaktionsteknik), e-mail: timo.suominen@abo.fi; Linnekoski, J. (Aalto Univ., School of Science and Technology, Espoo (Finland), Lab. of Industrial Chemistry)

    2011-11-15

    The research was directed towards methods of producing transportation bio-fuels via the synthesis-gas route, with emphasis on the synthesis-gas production and gas cleaning steps. The subtopics of the research project were (1) fuel characterisation and ash behaviour in the gasification step, (2) reaction mechanisms related to gas cleaning, (3) evaluations of alternative process configurations and applications and (4) international cooperation. VTT itself financed also two additional subtopics: (5) new analysis techniques and (6) hydrogen from biomass via gasification. The project comprised experimental work, modelling, techno-economic evaluations as well as studies based on literature. The project was steered by a wide industrial consortium and the research work was carried out by VTT, Aalto University and Aabo Akademi. International development in syngas technology was closely monitored in all subtopics as well as by participating in relevant IEA-tasks. More information on the project can be found on project webpage http://www.vtt.fi/proj/ucgfunda/ (orig.)

  13. Biomass staged-gasification characteristics in high-temperature entrained-flow bed%生物质高温气流床分级气化特性

    Institute of Scientific and Technical Information of China (English)

    陈超; 周劲松; 项阳阳; 顾珊; 骆仲泱

    2015-01-01

    为了满足生物质间接液化中对合成气组成的要求,特别是H2与CO体积比要达到1.0~2.0,采用生物质低温热解炉结合高温气流床的生物质分级气化系统,研究气流床分级气化方式对生物质气化合成气的影响.针对温度、一次气化时间等因素,研究合成气组分、H2与CO体积比、碳转化率、气化效率以及焦油质量浓度等方面的变化情况.结果表明,生物质分级气化和温度的升高均能够提高 H2与CO体积比.生物质分级气化系统的最佳工况是一次气化时间为0.6 s ,当气化温度为1100℃时,此时气化效果最好,气化效率达到75%,H2与CO体积比可达1.22,碳转化率达到96.3%.分级气化合成气中焦油质量浓度比传统气化明显减少,从5.46 g/m3降低到了50 mg/m3.%The raw material requirements for the indirect liquefaction of biomass are strict .The volume ratio of H2 to CO must be greater than or equal to 1 .0~2 .0 .The effect on biomass gasification syngas in staged‐gasification of biomass was analyzed .Biomass staged‐gasification system contained low temperature biomass pyrolysis furnace and high temperature entrained‐flow bed . Influence factors were studied including gasification temperature and first gasification time . T he result investigation contained composition of syngas ,volume ratio of H2 to CO ,carbon conversion ratio ,gasification efficiency and tar mass concentration . Results show that staged‐gasification and increasing temperature can enhance the volume ratio of H2 to CO .The optimum condition of staged gasification was the first gasification time at 0 .6 s and gasification temperature at 1 100 ℃ . The result was best in the conditions . Gasification efficiency was up to 75% ,the volume ratio of H2 to CO reached the maximum at 1 .22 ,and carbon conversion was up to 96 .3% .The tar mass concentration was decreased from 5 .46 g/m3 to 50 mg/m3 .

  14. Effects of lipids and oleic acid on biomass development in anaerobic fixed-bed reactors. Part II: Oleic acid toxicity and biodegradability.

    Science.gov (United States)

    Alves, M M; Vieira, J A; Pereira, R M; Pereira, M A; Mota, M

    2001-01-01

    Oleic acid toxicity and biodegradability were followed during long-term operation of two similar anaerobic fixed-bed units. When treating an oleate based effluent, the sludge from the bioreactor that was acclimated with lipids during the first operation period, showed a higher tolerance to oleic acid toxicity (IC50 = 137 mg/l) compared with the sludge fed with a non-fat substrate (IC50 = 80 mg/l). This sludge showed also the highest biodegradation capacity of oleic acid, achieving maximum methane production rates between 33 and 46 mlCH4(STP)/gVS.day and maximum percentages of methanization between 85 and 98% for the range of concentrations between 500 and 900 mg oleate/l. When oleate was the sole carbon source fed to both digesters, the biomass became encapsulated with organic matter, possibly oleate or an intermediate of its degradation, e.g. stearate that was degraded at a maximum rate of 99 mlCH4(STP)/gVS.day. This suggests the possibility of using adsorption-degradation cycles for the treatment of LCFA based effluents. Both tolerance to toxicity and biodegradability of oleic acid were improved by acclimatization with lipids or oleate below a threshold concentration.

  15. 内加热移动床生物质炭化中试设备监控系统开发%Monitoring and control system development for pilot-scale moving bed biomass carbonization equipment with internal heating

    Institute of Scientific and Technical Information of China (English)

    丛宏斌; 赵立欣; 孟海波; 姚宗路

    2015-01-01

    Biochar is a pyrolysis solid product of biological organic material (biomass) in anoxic and anaerobic conditions, It can be widely used in carbon emission reduction, water purification, adsorption of heavy metals and soil improvement, etc., so it can partly provide solutions for the focus issues of global concern, such as climate warming, environmental pollution and soil degradation. The production and application of biochar have aroused wide attention of researchers both at home and abroad. According to the continuity of production process, two types of biomass carbonization techniques have been developed in China, which are respectively fixed bed carbonization technique and moving bed carbonization technique. The fixed bed carbonization techniques can be divided into kiln carbonization technique and retort carbonization. Accordingly, the kiln carbonization technique commonly adopts spontaneous combustion heating method, its corresponding equipments have the features of simple structure and low-cost, so this technique has been used widely in China. The retort carbonization technique adopts external heating method, so its corresponding device has more complicated structure than the kiln carbonization technique, this technique can commonly realize the poly-generation of biochar and other byproducts. The moving bed carbonization technique is upgraded from the fixed bed carbonization technique, and according to flowing the direction of material, this technique can be divided into transverse flow moving bed carbonization technique and vertical flow moving bed carbonization technique. Continuous producing is the remarkable feature of the moving bed biomass carbonization technique, and it has higher automation level and lower labor intensity, compared with the fixed bed carbonization technique. The moving bed carbonization technique represents developing direction of China’s biomass carbonization technique. Aimed at the problems of low productivity, high energy

  16. Steam generators

    Energy Technology Data Exchange (ETDEWEB)

    Beckmann, G.; Gilli, P.V.; Fritz, K.; Lippitsch, J.

    1975-12-02

    A steam generator is disclosed which is particularly adapted to be used in nuclear power plants. A casing is provided with an inlet and outlet to receive and discharge a primary heating fluid from which heat is to be extracted. A pair of tube plates extend across the interior of the casing at the region of the inlet and outlet thereof, and a plurality of tubes extend along the interior of the casing and are connected in parallel between the tube plates with all of the tubes having open ends communicating with the inlet and outlet of the casing so that the primary heating fluid will flow through the interior of the tubes while a fluid in the casing at the exterior of the tubes will extract heat from the primary fluid. The casing has between the tubes at the region of the inlet a superheating chamber and at the region of the outlet a preheating chamber and between the latter chambers an evaporating chamber, the casing receiving water through an inlet at the preheating chamber and discharging superheated steam through an outlet at the superheating chamber. A separator communicates with the evaporating chamber to receive a mixture of steam and water therefrom for separating the steam from the water and for delivering the separated steam to the superheating chamber.

  17. Radioactive Demonstration Of Mineralized Waste Forms Made From Hanford Low Activity Waste (Tank SX-105, Tank AN-103, And AZ-101/102) By Fluidized Bed Steam Reformation (FBSR)

    Energy Technology Data Exchange (ETDEWEB)

    Jantzen, C. M.; Crawford, C. L.; Bannochie, C. J.; Burket, P. R.; Cozzi, A. D.; Daniel, W. E.; Hall, H. K.; Miller, D. H.; Missimer, D. M.; Nash, C. A.; Williams, M. F.

    2013-09-18

    Fluidized Bed Steam Reforming (FBSR) is a robust technology for the immobilization of a wide variety of radioactive wastes. Applications have been tested at the pilot scale for the high sodium, sulfate, halide, organic and nitrate wastes at the Hanford site, the Idaho National Laboratory (INL), and the Savannah River Site (SRS). Due to the moderate processing temperatures, halides, sulfates, and technetium are retained in mineral phases of the feldspathoid family (nepheline, sodalite, nosean, carnegieite, etc). The feldspathoid minerals bind the contaminants such as Tc-99 in cage (sodalite, nosean) or ring (nepheline) structures to surrounding aluminosilicate tetrahedra in the feldspathoid structures. The granular FBSR mineral waste form that is produced has a comparable durability to LAW glass based on the short term PCT testing in this study, the INL studies, SPFT and PUF testing from previous studies as given in the columns in Table 1-3 that represent the various durability tests. Monolithing of the granular product was shown to be feasible in a separate study. Macro-encapsulating the granular product provides a decrease in leaching compared to the FBSR granular product when the geopolymer is correctly formulated.

  18. Development of Catalytic Tar Decomposition in an Internally Circulating Fluidized-Bed Gasifier

    Science.gov (United States)

    Xiao, Xianbin; Le, Due Dung; Morishita, Kayoko; Li, Liuyun; Takarada, Takayuki

    Biomass gasification in an Internally Circulating Fluidized-bed Gasifier (ICFG) using Ni/Ah03 as tar cracking catalyst is studied at low temperature. Reaction conditions of the catalyst bed are discussed, including catalytic temperature and steam ratio. High energy efficiency and hydrogen-rich, low-tar product gas can be achieved in a properly designed multi-stage gasification process, together with high-performance catalyst. In addition, considering the economical feasibility, a newly-developed Ni-loaded brown coal char is developed and evaluated as catalyst in a lab-scale fluidized bed gasifier with catalyst fixed bed. The new catalyst shows a good ability and a hopeful prospect oftar decomposition, gas quality improvement and catalytic stability.

  19. Woody biomass and RPF gasification using reforming catalyst and calcium oxide.

    Science.gov (United States)

    Kobayashi, Jun; Kawamoto, Katsuya; Fukushima, Ryutaro; Tanaka, Shingo

    2011-05-01

    This study focused on steam gasification and reforming of waste biomass using a reforming catalyst. The purpose of the study was to evaluate the durability of a commercial Ni reforming catalyst and the effect of CaO on the reforming behavior, and to clarify detailed factors of catalytic performance, as well as the effect of operating parameters on the characteristics of produced gas composition. Moreover, catalyst regeneration was carried out and the behavior of catalytic activity based on gas composition was investigated. Using a fluidized bed gasifier and a fixed bed reformer, gasification and reforming of waste biomass were carried out. Commercial Ni-based catalyst and calcined limestone (CaO) were applied to the reforming reaction. Temperature of the gasifier and reformer was almost 1023K. Ratio of steam to carbon in the feedstock [molmol(-1)] and equivalence ratio (i.e., ratio of actual to theoretical amount of oxygen) [-] were set at about 2 and 0.3, respectively. The feed rate of the feedstock into the bench-scale gasifier was almost 15kgh(-1). The results of waste biomass gasification confirmed the improvement in H(2) composition by the CO(2) absorption reaction using the reforming catalyst and CaO. In addition, CaO proved to be especially effective in decreasing the tar concentration in the case of woody biomass gasification. Catalytic activity was maintained by means of catalyst regeneration processing by hydrogen reduction after air oxidation when woody biomass was used as feedstock.

  20. Investigations on catalyzed steam gasification of biomass. Appendix B: feasibility study of methanol production via catalytic gasification of 2000 tons of wood per day

    Energy Technology Data Exchange (ETDEWEB)

    Mudge, L.K.; Weber, S.L.; Mitchell, D.H.; Sealock, L.J. Jr.; Robertus, R.J.

    1981-01-01

    A study has been made of the economic feasibility of producing fuel grade methanol from wood via catalytic gasification with steam. The plant design in this study was developed from information on gasifier operation supplied by the Pacific Northwest Laboratory (PNL), operated by Battelle. PNL obtained this information from laboratory and process development unit testing. The plant is designed to process 2000 tons per day of dry wood to methanol. Plant production is 997 tons per day of methanol with a HHV of 9784 Btu per pound. All process and support facilities necessary to convert wood to methanol are included in this study. The plant location is Newport, Oregon. The capital cost for the plant is $120,830,000 - September 1980 basis. Methanol production costs which allow for return on capital have been calculated for various wood prices for both utility and private investor financing. These wood costs include delivery to the plant. For utility financing, the methanol production costs are respectively $.45, $.48, $.55, and $.69 per gallon for wood costs of $5, $10, $20, and $40 per dry ton. For private investor financing, the corresponding product costs are $.59, $.62, $.69, and $.83 per gallon for the corresponding wood costs. Both calculation methods include a return on equity capital in the costs. The thermal efficiency of the plant is 52.9%.

  1. Biomass IGCC

    Energy Technology Data Exchange (ETDEWEB)

    Salo, K.; Keraenen, H. [Enviropower Inc., Espoo (Finland)

    1996-12-31

    Enviropower Inc. is developing a modern power plant concept based on pressurised fluidized-bed gasification and gas turbine combined cycle (IGCC). The process is capable of maximising the electricity production with a variety of solid fuels - different biomass and coal types - mixed or separately. The development work is conducted on many levels. These and demonstration efforts are highlighted in this article. The feasibility of a pressurised gasification based processes compared to competing technologies in different applications is discussed. The potential of power production from biomass is also reviewed. (orig.) 4 refs.

  2. Catalytic gasification of biomass

    Science.gov (United States)

    Robertus, R. J.; Mudge, L. K.; Sealock, L. J., Jr.; Mitchell, D. H.; Weber, S. L.

    1981-12-01

    Methane and methanol synthesis gas can be produced by steam gasification of biomass in the presence of appropriate catalysts. This concept is to use catalysts in a fluidized bed reactor which is heated indirectly. The objective is to determine the technical and economic feasibility of the concept. Technically the concept has been demonstrated on a 50 lb per hr scale. Potential advantages over conventional processes include: no oxygen plant is needed, little tar is produced so gas and water treatment are simplified, and yields and efficiencies are greater than obtained by conventional gasification. Economic studies for a plant processing 2000 T/per day dry wood show that the cost of methanol from wood by catalytic gasification is competitive with the current price of methanol. Similar studies show the cost of methane from wood is competitive with projected future costs of synthetic natural gas. When the plant capacity is decreased to 200 T per day dry wood, neither product is very attractive in today's market.

  3. Investigations on catalyzed steam gasification of biomass: feasibility study of methane production via catalytic gasification of 200 tons of wood per day

    Energy Technology Data Exchange (ETDEWEB)

    Mudge, L.K.; Weber, S.L.; Mitchell, D.H.; Sealock, L.J. Jr.; Robertus, R.J.

    1981-01-01

    This report is a result of an additional study made of the economic feasibility of producing substitute natural gas (SNG) from wood via catalytic gasification with steam. The report has as its basis the original 2000 tons of wood per day study generated from process development unit testing performed by the Pacific Northwest Laboratory. The goal of this additional work was to determine the feasibility of a smaller scale plant one-tenth the size of the original or 200 tons of dry wood feed per day. Plant production based on this wood feed is 2.16 MM Scfd of SNG with a HHV of 956 Btu per Scf. All process and support facilities necessary to convert wood to SNG are included in this study. The plant location is Newport, Oregon. The capital cost for the plant is $26,680,000 - September 1980 basis. Gas production costs which allow for return on capital have been calculated for various wood prices for both utility and private investor financing. These wood prices represent the cost of unchipped wood delivered to the plant site. For utility financing, the gas production costs are, respectively, $14.34, $14.83, $15.86, and $17.84 per MM Btu for wood costs of $5, $10, $20, and $40 per dry ton. For private investor financing, the corresponding product costs are $18.76, $19.26, $20.28, and $22.31 per MM Btu for the corresponding wood costs. The costs calculated by the utility financing method includes a return on equity of 15% and an interest rate of 10% on the debt. The private investor financing method, which is 100% equity financing, incorporates a discounted cash flow (DCF) return on equity of 12%. The thermal efficiency without taking an energy credit for char is 57.4%.

  4. Investigations on catalyzed steam gasification of biomass. Appendix A. Feasibility study of methane production via catalytic gasification of 2000 tons of wood per day

    Energy Technology Data Exchange (ETDEWEB)

    Mudge, L.K.; Weber, S.L.; Mitchell, D.H.; Sealock, L.J. Jr.; Robertus, R.J.

    1981-01-01

    A study has been made of the economic feasibility of producing substitute natural gas (SNG) from wood via catalytic gasification with steam. The plant design in this study was developed from information on gasifier operation supplied by the Pacific Northwest Laboratory (PNL). The plant is designed to process 2000 tons per day of dry wood to SNG. Plant production is 21.6 MM scfd of SNG with a HHV of 956 Btu per scf. All process and support facilities necessary to convert wood to SNG are included. The plant location is Newport, Oregon. The capital cost for the plant is $95,115,000 - September, 1980 basis. Gas production costs which allow for return on capital have been calculated for various wood prices for both utility and private investor financing. For utility financing, the gas production costs are respectively $5.09, $5.56, $6.50, and $8.34 per MM Btu for wood costs of $5, $10, $20, and $40 per dry ton delivered to the plant at a moisture content of 49.50 wt %. For private investor financing, the corresponding product costs are $6.62, $7.11, $8.10, and $10.06 per MM Btu. The cost calculated by the utility financing method includes a return on equity of 15% and an interest rate of 10% on the debt. The private investor financing method, which is 100% equity financing, incorporates a discounted cash flow (DCF) return on equity of 12%. The thermal efficiency without taking an energy credit for by-product char is 58.3%.

  5. Investigations on catalyzed steam gasification of biomass: feasibility study of methanol production via catalytic gasification of 200 tons of wood per day

    Energy Technology Data Exchange (ETDEWEB)

    Mudge, L.K.; Weber, S.L.; Mitchell, D.H.; Sealock, L.J. Jr.; Robertus, R.J.

    1981-01-01

    This report is a result of an additional study made of the economic feasibility of producing fuel grade methanol from wood via catalytic gasification with steam. The report has as its basis the original 2000 tons of wood per day study generated from process development unit testing performed by the Pacific Northwest Laboratory (PNL). The goal of this additional work was to determine the feasibility of a smaller scale plant one tenth the size of the original or 200 tons of dry wood feed per day. Plant production based on this wood feed is 100 tons per day of methanol with a HHV of 9784 Btu per pound. All process and support facilities necessary to convert wood to methanol are included in this study. The plant location is Newport, Oregon. The capital cost for the plant is $34,830,000 - September 1980 basis. Methanol production costs which allow for return on capital have been calculated for various wood prices for both utility and private investor financing. These wood costs include delivery to the plant. For utility financing, the methanol production costs are, respectively, $1.20, $1.23, $1.30, and $1.44 per gallon for wood costs of $5, $10, $20, and $40 per dry ton. For private investor financing, the corresponding product costs are $1.60, $1.63, $1.70, and $1.84 per gallon for the corresponding wood costs. The costs calculated by the utility financing method include a return on equity of 15% and an interest rate of 10% on the debt. The private investor financing method, which is 100% equity financing, incorporates a discounted cash flow (DCF) return on equity of 12%. The thermal efficiency of the plant is 52.0%.

  6. Radioactive demonstration of final mineralized waste forms for Hanford waste treatment plant secondary waste (WTP-SW) by fluidized bed steam reforming (FBSR) using the bench scale reformer platform

    Energy Technology Data Exchange (ETDEWEB)

    Crawford, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Burket, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Cozzi, A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Daniel, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Jantzen, C. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Missimer, D. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2014-08-01

    The U.S. Department of Energy’s Office of River Protection (ORP) is responsible for the retrieval, treatment, immobilization, and disposal of Hanford’s tank waste. Currently there are approximately 56 million gallons of highly radioactive mixed wastes awaiting treatment. A key aspect of the River Protection Project (RPP) cleanup mission is to construct and operate the Waste Treatment and Immobilization Plant (WTP). The WTP will separate the tank waste into high-level and low-activity waste (LAW) fractions, both of which will subsequently be vitrified. The projected throughput capacity of the WTP LAW Vitrification Facility is insufficient to complete the RPP mission in the time frame required by the Hanford Federal Facility Agreement and Consent Order, also known as the Tri-Party Agreement (TPA), i.e. December 31, 2047. Therefore, Supplemental Treatment is required both to meet the TPA treatment requirements as well as to more cost effectively complete the tank waste treatment mission. In addition, the WTP LAW vitrification facility off-gas condensate known as WTP Secondary Waste (WTP-SW) will be generated and enriched in volatile components such as 137Cs, 129I, 99Tc, Cl, F, and SO4 that volatilize at the vitrification temperature of 1150°C in the absence of a continuous cold cap (that could minimize volatilization). The current waste disposal path for the WTP-SW is to process it through the Effluent Treatment Facility (ETF). Fluidized Bed Steam Reforming (FBSR) is being considered for immobilization of the ETF concentrate that would be generated by processing the WTP-SW. The focus of this current report is the WTP-SW.

  7. Effect of Steam Explosion Pretreatment on Bamboo for Enzymatic Hydrolysis and Ethanol Fermentation

    OpenAIRE

    Zhiqiang Li; Benhua Fei; Zehui Jiang

    2014-01-01

    Based on the steam explosion pretreatment that has been applied to other types of lignocellulosic biomass, the steam explosion pretreatment of bamboo, along with a study of the chemical compositions and enzymatic hydrolyzability of substrates, was conducted. The results show that steam explosion pretreatment can greatly enhance the cellulose-to-glucose conversion yield after enzymatic hydrolysis, which is sometimes affected by bamboo age and steam explosion conditions. When the steam explosio...

  8. Process for treating biomass

    Energy Technology Data Exchange (ETDEWEB)

    Campbell, Timothy J; Teymouri, Farzaneh

    2015-11-04

    This invention is directed to a process for treating biomass. The biomass is treated with a biomass swelling agent within the vessel to swell or rupture at least a portion of the biomass. A portion of the swelling agent is removed from a first end of the vessel following the treatment. Then steam is introduced into a second end of the vessel different from the first end to further remove swelling agent from the vessel in such a manner that the swelling agent exits the vessel at a relatively low water content.

  9. Process for treating biomass

    Science.gov (United States)

    Campbell, Timothy J.; Teymouri, Farzaneh

    2015-08-11

    This invention is directed to a process for treating biomass. The biomass is treated with a biomass swelling agent within the vessel to swell or rupture at least a portion of the biomass. A portion of the swelling agent is removed from a first end of the vessel following the treatment. Then steam is introduced into a second end of the vessel different from the first end to further remove swelling agent from the vessel in such a manner that the swelling agent exits the vessel at a relatively low water content.

  10. Non-catalytic co-gasification of sub-bituminous coal and biomass

    Science.gov (United States)

    Nyendu, Guevara Che

    Fluidization characteristics and co-gasification of pulverized sub-bituminous coal, hybrid poplar wood, corn stover, switchgrass, and their mixtures were investigated. Co-gasification studies were performed over temperature range from 700°C to 900°C in different media (N2, CO2, steam) using a bubbling fluidized bed reactor. In fluidization experiments, pressure drop (Delta P) observed for coal-biomass mixtures was higher than those of single coal and biomass bed materials in the complete fluidization regime. There was no systematic trend observed for minimum fluidization velocity ( Umf) with increasing biomass content. However, porosity at minimum fluidization (εmf) increased with increasing biomass content. Channeling effects were observed in biomass bed materials and coal bed with 40 wt.% and 50 wt.% biomass content at low gas flowrates. The effect of coal pressure overshoot reduced with increasing biomass content. Co-gasification of coal and corn stover mixtures showed minor interactions. Synergetic effects were observed with 10 wt.% corn stover. Coal mixed with corn stover formed agglomerates during co-gasification experiments and the effect was severe with increase in corn stover content and at 900°C. Syngas (H2 + CO) concentrations obtained using CO2 as co-gasification medium were higher (~78 vol.% at 700°C, ~87 vol.% at 800°C, ~93 vol.% at 900°C) than those obtained with N2 medium (~60 vol.% at 700°C, ~65 vol.% at 800°C, ~75 vol.% at 900°C). Experiments involving co-gasification of coal with poplar showed no synergetic effects. Experimental yields were identical to predicted yields. However, synergetic effects were observed on H2 production when steam was used as the co-gasification medium. Additionally, the presence of steam increased H2/CO ratio up to 2.5 with 10 wt.% hybrid poplar content. Overall, char and tar yields decreased with increasing temperature and increasing biomass content, which led to increase in product gas.

  11. Biomass CFB gasifier connected to a 350 MW{sub t}h steam boiler fired with coal and natural gas - THERMIE demonstration project in Lahti in Finland

    Energy Technology Data Exchange (ETDEWEB)

    Palonen, J. [Foster Wheeler Energia Oy, Varkaus (Finland). Varkaus Global New Products

    1997-12-31

    The successful experience in developing the advanced Foster Wheeler Energi Oy`s (former Ahlstroem Pyropower) Circulating Fluidized Bed combustion system subsequently led to the development of the CFB gasification technology in the early 1980s. The driving force for the developing work was the dramatic increase in oil price during the oil crises. The primary advantage of CFB gasification technology is that the it enables the substitution of expensive fuels e.g. oil or gas with cheap solid fuels. These cheap fuels are typically different types of waste woods, bark or other biofuels. In the CFB gasifier these solid fuels are converted to gaseous fuel which can be used instead of other expensive fuels. In some cases this also solves a waste disposal problem, providing a secondary economic and environmental benefit. Foster Wheeler Energia Oy has supplied four commercial scale atmospheric CFB gasifiers in the mid 80s to the pulp and paper industry with capacities from 17 to 35 MW based on fuel input. These applications utilize waste wood as feedstock and the units are still successfully operation today. Lahden Laempoevoima Oy is a Finnish power company producing power and district heat for the city of Lahti. The company is 50 % owned by the city of Lahti and 50 % by Imatran Voima Oy, which is the largest utility power company in Finland. Lahden Laempoevoima Oy operates the Kymijaervi power plant locating nearby the city of Lahti in Southern Finland. To keep the energy prices as low as possible, Lahden Laempoevoima is continuously looking for the most economical fuel sources, and simultaneously, trying to improve the environmental acceptability of the energy production. At the moment, about 300 GWh/a different type of biofuels and refuse fuels are available in the Lahti area. On an annual basis, the available amount of biofuels and refuse fuels is enough to substitute for about 15 % of the fuels burned in the main boiler equalling max 30 % of coal. The aim in this Lahden

  12. Effective Thermal Conductivity of Adsorbent Packed Beds

    Science.gov (United States)

    Mori, Hideo; Hamamoto, Yoshinori; Yoshida, Suguru

    The effective thermal conductivity of adsorbent packed beds of granular zeolite 13X and granular silica gel A in the presence of stagnant steam or air was measured under different conditions of the adsorbent bed temperature, particle size and filler-gas pressure. The measured effective thermal conductivity showed to become smaller with decreasing particle size or decreasing pressure, but it was nearly independent of the bed temperature. When steam was the filler-gas, the rise in the thermal conductivity of the adsorbent particles due to steam adsorption led to the increase in the effective thermal conductivity of the bed, and this effect was not negligible at high steam pressure for the bed of large particle size. It was found that both the predictions of the effective thermal conductivity by the Hayashi et al.'s model and the Bauer-Schlünder model generally agreed well with the measurements, by considering the particle thermal conductivity rise due to steam adsorption. The thermal conductivity of a consolidated bed of granular zeolite 13X was also measured, and it was found to be much larger than that of the packed bed especially at lower pressure. The above prediction models underestimated the effective thermal conductivity of the consolidated bed.

  13. Steam Drum Design for Direct Steam Generation

    OpenAIRE

    Willwerth, Lisa; Müller, Svenja; Krüger, Joachim; Succo, Manuel; Feldhoff, Jan Fabian; Tiedemann, Jörg; Pandian, Juvaraj; Krüger, Dirk; Hennecke, Klaus

    2016-01-01

    For the direct steam generation in solar fields, the recirculation concept has been demonstrated in several installations. Water masses in the solar field vary during transient phases, such as passing clouds. The volume of the steam drum can serve as a buffer during such transients by taking in excess water and providing water storage. The saturated steam mass flow to the superheating section or the consumer can be maintained almost constant during short transients; therefore the steam drum p...

  14. Hydrogen production from biomass gasification using biochar as a catalyst/support.

    Science.gov (United States)

    Yao, Dingding; Hu, Qiang; Wang, Daqian; Yang, Haiping; Wu, Chunfei; Wang, Xianhua; Chen, Hanping

    2016-09-01

    Biochar is a promising catalyst/support for biomass gasification. Hydrogen production from biomass steam gasification with biochar or Ni-based biochar has been investigated using a two stage fixed bed reactor. Commercial activated carbon was also studied as a comparison. Catalyst was prepared with an impregnation method and characterized by X-ray diffraction, specific surface and porosity analysis, X-ray fluorescence and scanning electron micrograph. The effects of gasification temperature, steam to biomass ratio, Ni loading and bio-char properties on catalyst activity in terms of hydrogen production were explored. The Ni/AC catalyst showed the best performance at gasification temperature of 800°C, S/B=4, Ni loading of 15wt.%. Texture and composition characterization of the catalysts suggested the interaction between volatiles and biochar promoted the reforming of pyrolysis volatiles. Cotton-char supported Ni exhibited the highest activity of H2 production (64.02vol.%, 92.08mgg(-1) biomass) from biomass gasification, while rice-char showed the lowest H2 production.

  15. Hydrogen production from glucose and sorbitol by sorption-enhanced steam reforming: challenges and promises.

    Science.gov (United States)

    He, Li; Chen, De

    2012-03-12

    Concerning energy and environmental sustainability, it is appealing to produce hydrogen from sugars or sugar alcohols that are readily obtained from the hydrolysis of cellulosic biomass. Nevertheless, the conversion of such compounds for hydrogen production poses great technical challenges. In this paper, we report that hydrogen purity and yield can be significantly improved by integrating in situ CO(2) capture into the steam reforming reaction of the model compounds-glucose and sorbitol. The experimental assessment was conducted at a steam-to-carbon ratio of 1.8 for sorbitol and 6 for glucose from 450-625 °C. As predicted by thermodynamic analysis, combining CO(2) capture and reforming reactions at favorable operating conditions yielded very high purity hydrogen, for instance, 98.8 mol % from sorbitol and 99.9 mol % from glucose. However, there are trade-offs between hydrogen purity and yield in practice. The lower operating temperatures in the examined range helped to increase the hydrogen purity and reduce the CO content in the gas product, whereas a high hydrogen yield was more likely to be obtained at higher temperatures. Coupling CO(2) capture lowered the risk of coke formation during the steam reforming of glucose. Coke accumulated in the reactor for the sorption-enhanced steam reforming of glucose was mostly from the slow pyrolysis of glucose before it came into contact with the catalyst-acceptor bed. This problem may be solved by improving heat transfer or reconstructing the reactor, for instance, by using a fluidized-bed reactor.

  16. Research and evaluation of biomass resources/conversion/utilization systems (market/experimental analysis for development of a data base for a fuels from biomass model). Quarterly technical progress report, Februray 1, 1980-April 30, 1980

    Energy Technology Data Exchange (ETDEWEB)

    Ahn, Y.K.; Chen, Y.C.; Chen, H.T.; Helm, R.W.; Nelson, E.T.; Shields, K.J.

    1980-01-01

    The project will result in two distinct products: (1) a biomass allocation model which will serve as a tool for the energy planner. (2) the experimental data is being generated to help compare and contrast the behavior of a large number of biomass material in thermochemical environments. Based on information in the literature, values have been developed for regional biomass costs and availabilities and for fuel costs and demands. This data is now stored in data banks and may be updated as better data become available. Seventeen biomass materials have been run on the small TGA and the results partially analyzed. Ash analysis has been performed on 60 biomass materials. The Effluent Gas Analyzer with its associated gas chromatographs has been made operational and some runs have been carried out. Using a computerized program for developing product costs, parametric studies on all but 1 of the 14 process configurations being considered have been performed. Background economic data for all the configuration have been developed. Models to simulate biomass gasifications in an entrained and fixed bed have been developed using models previously used for coal gasification. Runs have been carried out in the fluidized and fixed bed reactor modes using a variety of biomass materials in atmospheres of steam, O/sub 2/ and air. Check aout of the system continues using fabricated manufacturing cost and efficiency data. A users manual has been written.

  17. Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

    Energy Technology Data Exchange (ETDEWEB)

    Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E. [IVO International Oy, Vantaa (Finland)

    1995-12-31

    Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

  18. Theoretical investigation of tar conversion in fluidized-bed gasification processes; Theoretische Untersuchung des Teerumsatzes bei der Wirbelschichtvergasung

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, S.; Hasselbach, H.; Krumm, W. [Siegen Univ., Inst. fuer Energietechnik (Germany)

    2002-07-01

    A mathematical model for simulating stationary fluidized-bed systems is used for a theoretical investigation of the influence of various operating parameters of atmospheric air/steam biomass gasification on the tars contained in the product gas. The variation of the evacuated tube velocity in the fluidized bed, the influence of fuel particle size, and the position of fuel supply are investigated in detail, followed by a discussion and plausibility assessment of the results. [German] Ein mathematisches Modell zur Simulation von stationaeren Wirbelschichtvergasern wird herangezogen, um den Einfluss verschiedener Betriebsparameter einer atmosphaerischen Luft/Dampf-Vergasung von Biomasse auf die im Produktgas enthaltenen Teere theoretisch zu untersuchen. Dabei wird neben der Variation der Leerrohrgeschwindigkeit im Wirbelbett, die Stufung der Vergasungsmittelzugabe, der Einfluss der Brennstoffpartikelgroesse und der Position der Brennstoffzufuhr detailliert untersucht. Es erfolgt eine eingehende Diskussion und Plausibilitaetsbetrachtung der Ergebnisse. (orig.)

  19. Hydrogen-Rich Gas Production by Sorption Enhanced Steam Reforming of Woodgas Containing TAR over a Commercial Ni Catalyst and Calcined Dolomite as CO2 Sorbent

    Directory of Open Access Journals (Sweden)

    Vincenzo Naso

    2013-07-01

    Full Text Available The aim of this work was the evaluation of the catalytic steam reforming of a gaseous fuel obtained by steam biomass gasification to convert topping atmosphere residue (TAR and CH4 and to produce pure H2 by means of a CO2 sorbent. This experimental work deals with the demonstration of the practical feasibility of such concepts, using a real woodgas obtained from fluidized bed steam gasification of hazelnut shells. This study evaluates the use of a commercial Ni catalyst and calcined dolomite (CaO/MgO. The bed material simultaneously acts as reforming catalyst and CO2 sorbent. The experimental investigations have been carried out in a fixed bed micro-reactor rig using a slipstream from the gasifier to evaluate gas cleaning and upgrading options. The reforming/sorption tests were carried out at 650 °C while regeneration of the sorbent was carried out at 850 °C in a nitrogen environment. Both combinations of catalyst and sorbent are very effective in TAR and CH4 removal, with conversions near 100%, while the simultaneous CO2 sorption effectively enhances the water gas shift reaction producing a gas with a hydrogen volume fraction of over 90%. Multicycle tests of reforming/CO2 capture and regeneration were performed to verify the stability of the catalysts and sorbents to remove TAR and capture CO2 during the duty cycle.

  20. Recent advances in AFB biomass gasification pilot plant with catalytic reactors in a downstream slip flow

    Energy Technology Data Exchange (ETDEWEB)

    Aznar, M.P.; Gil, J.; Martin, J.A.; Frances, E.; Olivares, A.; Caballero, M.A.; Perez, P. [Saragossa Univ. (Spain). Dept. of Chemistry and Environment; Corella, J. [Madrid Univ. (Spain)

    1996-12-31

    A new 3rd generation pilot plant is being used for hot catalytic raw gas cleaning. It is based on a 15 cm. i.d. fluidized bed with biomass throughputs of 400-650 kg/h.m{sup 2}. Gasification is performed using mixtures of steam and oxygen. The produced gas is passed in a slip flow by two reactors in series containing a calcined dolomite and a commercial reforming catalyst. Tars are periodically sampled and analysed after the three reactors. Tar conversions of 99.99 % and a 300 % increase of the hydrogen content in the gas are obtained. (author) (2 refs.)

  1. Potentials of Selected Malaysian Biomasses as Co-Gasification Fuels with Oil Palm Fronds in a Fixed-Bed Downdraft Gasifier

    Directory of Open Access Journals (Sweden)

    Moni Mohamad Nazmi Zaidi

    2014-07-01

    Full Text Available Oil palm frond (OPF has been successfully gasified to produce syngas and has since deemed as a potential source of biomass fuel in Malaysia. However, if OPF is to be utilized as a main fuel for industrial-scale firing/gasification plant, interruption in fuel supply may occur due to numerous reasons, for instance inefficient fuel processing and ineffective transportation. A secondary supporting solid fuel is therefore necessary as a partial component to the main fuel in such cases, where the secondary fuel is combusted with the main fuel to adhere to main fuel shortage. Gasification of two fuels together, known as co-gasification, is practiced worldwide, some in industrial scale. However, current practice utilizes biomass fuel as the secondary fuel to coal in co-gasification. This investigation explores into the feasibility of co-gasifying two biomass fuels together to produce syngas. OPF was chosen as the primary fuel and a selection of Malaysian biomasses were studied to discover their compatibility with OPF in co-gasification. Biomass selection was made using score-and-rank method and their selection criteria are concisely discussed.

  2. Biomass thermochemical gasification: Experimental studies and modeling

    Science.gov (United States)

    Kumar, Ajay

    The overall goals of this research were to study the biomass thermochemical gasification using experimental and modeling techniques, and to evaluate the cost of industrial gas production and combined heat and power generation. This dissertation includes an extensive review of progresses in biomass thermochemical gasification. Product gases from biomass gasification can be converted to biopower, biofuels and chemicals. However, for its viable commercial applications, the study summarizes the technical challenges in the gasification and downstream processing of product gas. Corn stover and dried distillers grains with solubles (DDGS), a non-fermentable byproduct of ethanol production, were used as the biomass feedstocks. One of the objectives was to determine selected physical and chemical properties of corn stover related to thermochemical conversion. The parameters of the reaction kinetics for weight loss were obtained. The next objective was to investigate the effects of temperature, steam to biomass ratio and equivalence ratio on gas composition and efficiencies. DDGS gasification was performed on a lab-scale fluidized-bed gasifier with steam and air as fluidizing and oxidizing agents. Increasing the temperature resulted in increases in hydrogen and methane contents and efficiencies. A model was developed to simulate the performance of a lab-scale gasifier using Aspen Plus(TM) software. Mass balance, energy balance and minimization of Gibbs free energy were applied for the gasification to determine the product gas composition. The final objective was to optimize the process by maximizing the net energy efficiency, and to estimate the cost of industrial gas, and combined heat and power (CHP) at a biomass feedrate of 2000 kg/h. The selling price of gas was estimated to be 11.49/GJ for corn stover, and 13.08/GJ for DDGS. For CHP generation, the electrical and net efficiencies were 37 and 86%, respectively for corn stover, and 34 and 78%, respectively for DDGS. For

  3. Steam feed and effect of steam-thermal seal in thermolysis of tire shreds in a screw-type reactor

    Science.gov (United States)

    Kalitko, V. A.

    2010-05-01

    On the basis of experience in commercial operation, the effect of steam seal in tire-shred pyrolysis in a screw-type reactor with superheated steam has been considered and analytically substantiated; there, local steam feed produces the above effect at the total reduced pressure and keeps air from entering the reactor without sluices or valves used for hermetization of its loading and unloading. It has been shown that the increase in the production rate of pyrolysis due to the heating by steam amounts to 10-15% and is limited by the diffusion transfer in the reactor’s charge bed.

  4. INTEGRATION OF KRAFT PULPING ON A FOREST BIOREFINERY BY THE ADDITION OF A STEAM EXPLOSION PRETREATMENT

    OpenAIRE

    Raquel Martin-Sampedro; Maria E. Eugenio; Esteban Revilla; Juan A. Martin; J. Carlos Villar

    2011-01-01

    Steam explosion has been proposed for a wide range of lignocellulosic applications, including fractionation of biomass, pre-treatment of biomass for ethanol production, or as an alternative to conventional mechanical pulping. Nevertheless, a steam explosion process could also be used as pretreatment before chemical pulping, expecting a reduction in cooking time due to the open structure of the exploded chips. Thus, to evaluate the effect of steam explosion as a pretreatment in the kraft pulpi...

  5. Integration of torrefaction with steam power plant

    Energy Technology Data Exchange (ETDEWEB)

    Zakri, B.; Saari, J.; Sermyagina, E.; Vakkilainen, E.

    2013-09-01

    Torrefaction is one of the pretreatment technologies to enhance the fuel characteristics of biomass. The efficient and continuous operation of a torrefaction reactor, in the commercial scale, demands a secure biomass supply, in addition to adequate source of heat. Biorefinery plants or biomass-fuelled steam power plants have the potential to integrate with the torrefaction reactor to exchange heat and mass, using available infrastructure and energy sources. The technical feasibility of this integration is examined in this study. A new model for the torrefaction process is introduced and verified by the available experimental data. The torrefaction model is then integrated in different steam power plants to simulate possible mass and energy exchange between the reactor and the plants. The performance of the integrated plant is investigated for different configurations and the results are compared. (orig.)

  6. An Experimental and Numerical Investigation of Fluidized Bed Gasification of Solid Waste

    Directory of Open Access Journals (Sweden)

    Sharmina Begum

    2013-12-01

    Full Text Available Gasification is a thermo-chemical process to convert carbon-based products such as biomass and coal into a gas mixture known as synthetic gas or syngas. Various types of gasification methods exist, and fluidized bed gasification is one of them which is considered more efficient than others as fuel is fluidized in oxygen, steam or air. This paper presents an experimental and numerical investigation of fluidized bed gasification of solid waste (SW (wood. The experimental measurement of syngas composition was done using a pilot scale gasifier. A numerical model was developed using Advanced System for Process ENgineering (Aspen Plus software. Several Aspen Plus reactor blocks were used along with user defined FORTRAN and Excel code. The model was validated with experimental results. The study found very similar performance between simulation and experimental results, with a maximum variation of 3%. The validated model was used to study the effect of air-fuel and steam-fuel ratio on syngas composition. The model will be useful to predict the various operating parameters of a pilot scale SW gasification plant, such as temperature, pressure, air-fuel ratio and steam-fuel ratio. Therefore, the model can assist researchers, professionals and industries to identify optimized conditions for SW gasification.

  7. High temperature solid oxide fuel cell integrated with novel allothermal biomass gasification. Part II: Exergy analysis

    Science.gov (United States)

    Panopoulos, K. D.; Fryda, L.; Karl, J.; Poulou, S.; Kakaras, E.

    Biomass gasification derived gas is a renewable fuel, which can be used for SOFC applications. This work investigates the integration of a near atmospheric solid oxide fuel cell (SOFC) with a novel allothermal biomass steam gasification process into a combined heat and power (CHP) system of less than MW e range. Heat for steam gasification is supplied from SOFC depleted fuel in a fluidised bed (FB) combustor via high temperature sodium heat pipes. In the first paper, the integrated system was modelled in Aspen Plus™ and critical aspects for its feasibility were identified. The aim of this second part is the evaluation of the integrated system in exergy terms. Satisfying allothermal gasification heat demand is illustrated by examining each sub-process involved separately as well as combined. For a relatively low STBR = 0.6, the SOFC fuel utilisation for which the system operates under optimum conditions is U f = 0.7. Above that value additional biomass has to be used in the FB combustor to provide gasification heat with considerable exergy losses. For SOFC operation at current density 2500 A m -2, the system uses 90 kg h -1 biomass, operates with electrical exergetic efficiency 32% producing 140 kW e, while the combined electrical and thermal exergetic efficiency is 35%.

  8. Steam Digest 2001

    Energy Technology Data Exchange (ETDEWEB)

    2002-01-01

    Steam Digest 2001 chronicles BestPractices Program's contributions to the industrial trade press for 2001, and presents articles that cover technical, financial and managerial aspects of steam optimization.

  9. Adaptation to the KMT Fixed Biomass on Moving Bed process in the waste water treatment plant in Tafalla and Olite, Navarra, Spain; Adaptacion al proceso KMT de Biomasa Fija sobre Lecho Movil en la EDAR de Tafalla y Olite

    Energy Technology Data Exchange (ETDEWEB)

    Cortacans, J. A.; Rodrigo, J. C.; Garcia Gamuza, J.

    2001-07-01

    This article describes the remodeling carried out on the Tafalla and Olite waste water treatment plant in 2000to enable it to cope with a larger flow and load without having to construct new treatment lines. This was made possible by adapting the existing conventional active sludge process to the KMT Fixed Biomass on Moving Bed process. The article also shows how the final two-stage design was verified by means of pilot plant trials. These experiments tested the technical viability of installing a first high-load reactor prior to the existing primary decantation as a way of dealing with the seasonal effluents from the wine-cellars in the region and of obtaining partial nitrification in the last biological tank of the second stage during the rest of the year. (Author) 7 refs.

  10. Potentials of Selected Malaysian Biomasses as Co-Gasification Fuels with Oil Palm Fronds in a Fixed-Bed Downdraft Gasifier

    OpenAIRE

    Moni Mohamad Nazmi Zaidi; Sulaiman Shaharin Anwar; Hassan Suhaimi

    2014-01-01

    Oil palm frond (OPF) has been successfully gasified to produce syngas and has since deemed as a potential source of biomass fuel in Malaysia. However, if OPF is to be utilized as a main fuel for industrial-scale firing/gasification plant, interruption in fuel supply may occur due to numerous reasons, for instance inefficient fuel processing and ineffective transportation. A secondary supporting solid fuel is therefore necessary as a partial component to the main fuel in such cases, where the ...

  11. Bed Bugs

    Science.gov (United States)

    Prevent, identify, and treat bed bug infestations using EPA’s step-by-step guides, based on IPM principles. Find pesticides approved for bed bug control, check out the information clearinghouse, and dispel bed bug myths.

  12. Steam Digest Volume IV

    Energy Technology Data Exchange (ETDEWEB)

    None

    2004-07-01

    This edition of the Steam Digest is a compendium of 2003 articles on the technical and financial benefits of steam efficiency, presented by the stakeholders of the U.S. Department of Energy's BestPractices Steam effort.

  13. The Invisibility of Steam

    Science.gov (United States)

    Greenslade, Thomas B., Jr.

    2014-01-01

    Almost everyone "knows" that steam is visible. After all, one can see the cloud of white issuing from the spout of a boiling tea kettle. In reality, steam is the gaseous phase of water and is invisible. What you see is light scattered from the tiny droplets of water that are the result of the condensation of the steam as its temperature…

  14. Tar Management and Recycling in Biomass Gasification and Syngas Purification

    Science.gov (United States)

    McCaffrey, Zach

    Removal of tars is critical to the design and operation of biomass gasification systems as most syngas utilization processing equipment (e.g. internal combustion engines, gas turbines, fuel cells, and liquid fuel synthesis reactors) have a low tolerance for tar. Capturing and disposal of tar is expensive due to equipment costs, high hazardous waste disposal costs where direct uses cannot be found, and system energy losses incurred. Water scrubbing is an existing technique commonly used in gasification plants to remove contaminants and tar; however using water as the absorbent is non-ideal as tar compounds have low or no water solubility. Hydrophobic solvents can improve scrubber performance and this study evaluated tar solubility in selected solvents using slip-streams of untreated syngas from a laboratory fluidized bed reactor operated on almond composite feedstock using both air and steam gasification. Tar solubility was compared with Hansen's solubility theory to examine the extent to which the tar removal can be predicted. As collection of tar without utilization leads to a hazardous waste problem, the study investigated the effects of recycling tars back into the gasifier for destruction. Prior to experiments conducted on tar capture and recycle, characterizations of the air and steam gasification of the almond composite mix were made. This work aims to provide a better understanding of tar collection and solvent selection for wet scrubbers, and to provide information for designing improved tar management systems for biomass gasification.

  15. Thermochemical behavior of pretreated biomass

    Energy Technology Data Exchange (ETDEWEB)

    Biswas, Amit Kumar

    2011-07-01

    Mankind has to provide a sustainable alternative to its energy related problems. Bioenergy is considered as one of the potential renewable energy resources and as a result bioenergy market is also expected to grow dramatically in future. However, logistic issues are of serious concern while considering biomass as an alternative to fossil fuel. It can be improved by introducing pretreated wood pellet. The main objective of this thesis is to address thermochemical behaviour of steam exploded pretreated biomass. Additionally, process aspects of torrefaction were also considered in this thesis. Steam explosion (SE) was performed in a laboratory scale reactor using Salix wood chips. Afterwards, fuel and thermochemical aspects of SE residue were investigated. It was found that Steam explosion pretreatment improved both fuel and pellet quality. Pyrolysis of SE residue reveals that alerted biomass composition significantly affects its pyrolysis behaviour. Contribution from depolymerized components (hemicellulose, cellulose and lignin) of biomass was observed explicitly during pyrolysis. When devolatilization experiment was performed on pellet produced from SE residue, effect of those altered components was observed. In summary, pretreated biomass fuel characteristics is significantly different in comparison with untreated biomass. On the other hand, Process efficiency of torrefaction was found to be governed by the choice of appropriate operating conditions and the type of biomass.

  16. DEVELOPMENT OF A NANO-Ni-La-Fe/Al2O3 CATALYST TO BE USED FOR SYN-GAS PRODUCTION AND TAR REMOVAL AFTER BIOMASS GASIFICATION

    Directory of Open Access Journals (Sweden)

    Jianfen Li

    2009-11-01

    Full Text Available The objective of this study was to develop a supported tri-metallic catalyst (nano-Ni-La-Fe/γ-Al2O3 for tar removal in biomass steam gasification, to significantly enhance the quality of the produced gas. For this purpose, the supported tri-metallic catalysts were prepared by a deposition-precipitation (DP method. Different analytical approaches were used to characterize the synthesized catalysts. The results showed that the prepared tri-metallic catalysts had an egg-shell structure with a specific surface area of 214.7 m2/g. The activity of the catalysts for gas production and tar removal in the process of biomass gasification was also investigated using a bench-scale combined fixed bed reactor. The experiments indicated that the tar yield after adding catalyst was reduced significantly and the efficiency of tar removal reached 99% for the biomass steam gasification at 800oC, while the gas yield after adding catalysts increased markedly and less coke was found over the catalyst. Meanwhile, the compositions of gas products before and after adding catalyst in the process also changed significantly; in particular, the content of hydrogen in catalytic steam gasification was improved by over 10 vol%. Therefore, using the prepared tri-metallic catalyst in biomass gasification can significantly improve the quality of the produced gas and efficiently eliminate the tar generation, preventing coke deposition on the catalyst surfaces, thus demonstrating a long lifetime of the catalyst.

  17. High temperature solid oxide fuel cell integrated with novel allothermal biomass gasification. Part I: Modelling and feasibility study

    Science.gov (United States)

    Panopoulos, K. D.; Fryda, L. E.; Karl, J.; Poulou, S.; Kakaras, E.

    Biomass gasification derived fuel gas is a renewable fuel that can be used by high temperature fuel cells. In this two-part work an attempt is made to investigate the integration of a near atmospheric pressure solid oxide fuel cell (SOFC) with a novel allothermal biomass steam gasification process into a combined heat and power (CHP) system of less than MW e nominal output range. Heat for steam gasification is supplied from SOFC depleted fuel into a fluidised bed combustor via high temperature sodium heat pipes. The integrated system model was built in Aspen Plus™ simulation software and is described in detail. Part I investigates the feasibility and critical aspects of the system based on modelling results. A low gasification steam to biomass ratio (STBR = 0.6) is used to avoid excess heat demands and to allow effective H 2S high temperature removal. Water vapour is added prior to the anode to avoid carbon deposition. The SOFC off gases adequately provide gasification heat when fuel utilisation factors are f = 0.7 and current density 2500 A m -2 the electrical efficiency is estimated at 36% while thermal efficiency at 14%. An exergy analysis is presented in Part II.

  18. Energy efficient production of hydrogen and syngas from biomass: development of low-temperature catalytic process for cellulose gasification.

    Science.gov (United States)

    Asadullah, Mohammad; Ito, Shin-ichi; Kunimori, Kimio; Yamada, Muneyoshi; Tomishige, Keiichi

    2002-10-15

    The Rh/CeO2/M (M = SiO2, Al2O3, and ZrO2) type catalysts with various compositions have been prepared and investigated in the gasification of cellulose, a model compound of biomass, in a fluidized bed reactor at 500-700 degrees C. The conventional nickel and dolomite catalysts have also been investigated. Among the catalysts, Rh/CeO2/SiO2 with 35% CeO2 has been found to be the best catalyst with respect to the carbon conversion to gas and product distribution. The steam addition contributed to the complete conversion of cellulose to gas even at 600 degrees C. Lower steam supply gave the syngas and higher steam supply gave the hydrogen as the major product. Hydrogen and syngas from cellulose or cellulosic biomass gasification are environmentally super clean gaseous fuels for power generation. Moreover, the syngas derived liquid fuels such as methanol, dimethyl ether, and synthetic diesels are also super clean transportation fuels. However, the use of cellulose or cellulosic biomass for energy source through the gasification is challenging because of the formation of tar and char during the gasification process. It is interesting that no tar or char was finally formed in the effluent gas at as low as 500-600 degrees C using Rh/CeO2/SiO2(35) catalyst in this process.

  19. Tar formation in a steam-O2 blown CFB gasifier and a steam blown PBFB gasifier (BabyHPR): Comparison between different on-line measurement techniques and the off-line SPA sampling and analysis method

    NARCIS (Netherlands)

    Meng, X.; Mitsakis, P.; Mayerhofen, M.; De Jong, W.; Gaderer, M.; Verkooijen, A.H.M.; Spliethoff, H.

    2012-01-01

    Two on-line tar measurement campaigns were carried out using an atmospheric pressure 100 “”kWth steam-O2 blown circulating fluidized bed (CFB) gasifier at the Delft University of Technology (TUD) and a 30–40kWth steam blown pressurized bubbling fluidized bed (PBFB) gasifier BabyHPR (Heatpipe Reforme

  20. Hydrogen production from biomass. Optimization of gasification by experimental by experimental statistical design; Produccion de hidrogeno a partir de biomasa. Optimizacion de la gasificacion por aplicacion del diseno estadistico de experimentos

    Energy Technology Data Exchange (ETDEWEB)

    Arteche Calvo, A.

    2008-07-01

    Biomass conversion into a gas with high content in hydrogen is considered as a future alternative to obtain energy and chemicals products for renewable sources. One of the current technologies for this purpose is the gasification using steam as gasification agent. The technical objective of this work is the study of the process of biomass gasification with steam and oxygen as thermochemical process of transformation of biomass to obtain the maximum amount of hydrogen with lowest tar content. Materials and Methods. An experimental statistical strategy with three variables and two levels of operation was planned to optimize the gasification process. the study was conducted without changing the type of biomass-fed, the type of catalyst used and the quantity of bed inside the gasifier. Two mathematical models have been obtained as results. Both of them correlated the experimental factors to the production of hydrogen and tars. The design of experiments methodology has been applied to assess the influence os several experimental factors, such as the introduced amount of steam, the use of catalyst and oxygen, both in the production of hydrogen, as in the minimization of the formation of tars. This statistical technique has enabled the modeling of the selected biomass gasification performing the minimum number of pilot plant tests to identify possible improvements and optimizations both in the yield of produced hydrogen as in the generation of tars. (Author) 10 refs.

  1. Gasification reactivity and ash behaviour of biomass fuels

    Energy Technology Data Exchange (ETDEWEB)

    Moilanen, A.; Kurkela, E. [VTT Energy, Espoo (Finland)

    1998-12-31

    Measuring data required for describing the reactivity and ash sintering behaviour of biomass-based solid fuels for atmospheric and pressurised gasification are discussed. The measurements were carried out in a pressurisable thermobalance and bench-scale fluidised bed reactors. The main variables were temperature and partial pressures of H{sub 2}O and H{sub 2}, and CO{sub 2} and CO. The reaction rates were determined in binary gas mixtures H{sub 2}O-H{sub 2}, and CO{sub 2}-CO as well as in product gas mixtures H{sub 2}O-H{sub 2}-CO{sub 2}-CO. The total pressure range was 1-30 bar and the temperature range 650-950 deg C. For wood, kinetic parameters were determined using the Langmuir-Hinshelwood kinetics, which takes into account the effect of the product gases on the reaction rate. The results indicated that the H{sub 2}O-H{sub 2} system was well in conformity with this kinetics, while the reaction rates measured for the CO{sub 2}-CO system required the description of the catalytic effects of the ash-forming material. In the gasification of wood as well as of other biomasses, the behaviour of catalytically active ash components is more complex during char gasification. Experimental set-ups used for gasification reactivity measurements were compared in Aabo Akademi University and in VTT. The set-ups were pressurised thermogravimetric reactor (PTG), pressurised grid heater (PGH), pressurised bench-scale fluidised bed reactor (PFB), and pressurised entrained flow reactor (PEF). In addition, the effect of stabilising heat treatment was tested. The samples used in the study were wood, black liquor, peat, and coal. The gasification reactivity measurements were carried out in the temperature range of 700-950 deg C, and in the pressure range of 1-10 bar. The gasification agent was either CO{sub 2} in N{sub 2} or CO-CO{sub 2} mixture in N{sub 2}. In the pyrolysis carried out in different devices, mainly the same pressure and temperature were used as in the char gasification

  2. Reduced ash related operational problems (slagging, bed agglomeration, corrosion and fouling) by co-combustion biomass with peat; Minskade askrelaterade driftsproblem (belaeggning, slaggning, hoegtemperatur-korrosion, baeddagglomerering) genom inblandning av torv i biobraenslen

    Energy Technology Data Exchange (ETDEWEB)

    Oehman, Marcus; Boman, Christoffer; Erhardsson, Thomas; Gilbe, Ram; Pommer, Linda; Bostroem, Dan; Nordin, Anders; Samuelsson, Robert; Burvall, Jan

    2006-12-15

    Combustion studies were performed in both a fluidized bed (5 kW) and in an under-feed pellets burner (20 kW) to elucidate the responsible mechanisms for the positive effects on ash related operational problems (i.e. slagging, fouling, corrosion and bed agglomeration) during co-combustion of several problematic biomass with peat. Three typical carex-containing Swedish peat samples with differences in e.g. silicon-, calcium- and sulfur contents were co-fired with logging residues, willow and straw in proportions corresponding to 15-40 weight %d.s. Mixing of corresponding 20 wt-% of peat significantly reduced the bed agglomeration tendencies for all fuels. The fuel specific agglomeration temperature were increased by 150-170 deg C when adding peat to the straw fuel and approximately 70-100 deg C when adding peat to the logging residue- and the willow fuel. The increased level of calcium in the inner bed particle layer caused by the added reactive calcium from the peat and/or removing alkali in the gas phase to a less reactive particular form via sorption and/or reaction with reactive peat ash (containing calcium, silica etc.) during which larger particles (>1{mu}m) are formed where collected potassium is present in a less reactive form, is considered to be the dominated reason for the increased agglomeration temperatures during combustion of logging residues and willow. During straw combustion, the ash forming matter were found as individual ash sticky particles in the bed. The iron, sulphur and calcium content of these individual ash particles were significantly increased when adding peat to the fuel mix thereby decreasing the stickiness of these particles i.e. reducing the agglomeration tendencies. Adding peat to the relatively silicon-poor fuels (willow and logging residues) resulted in higher slagging tendencies, especially when the relative silicon rich peat fuel (Brunnskoelen) was used. However, when co-combusting peat with the relatively silicon and potassium

  3. Reduced ash related operational problems (slagging, bed agglomeration, corrosion and fouling) by co-combustion biomass with peat; Minskade askrelaterade driftsproblem (belaeggning, slaggning, hoegtemperatur-korrosion, baeddagglomerering) genom inblandning av torv i biobraenslen

    Energy Technology Data Exchange (ETDEWEB)

    Oehman, Marcus; Boman, Christoffer; Erhardsson, Thomas; Gilbe, Ram; Pommer, Linda; Bostroem, Dan; Nordin, Anders; Samuelsson, Robert; Burvall, Jan

    2006-12-15

    Combustion studies were performed in both a fluidized bed (5 kW) and in an under-feed pellets burner (20 kW) to elucidate the responsible mechanisms for the positive effects on ash related operational problems (i.e. slagging, fouling, corrosion and bed agglomeration) during co-combustion of several problematic biomass with peat. Three typical carex-containing Swedish peat samples with differences in e.g. silicon-, calcium- and sulfur contents were co-fired with logging residues, willow and straw in proportions corresponding to 15-40 weight %d.s. Mixing of corresponding 20 wt-% of peat significantly reduced the bed agglomeration tendencies for all fuels. The fuel specific agglomeration temperature were increased by 150-170 deg C when adding peat to the straw fuel and approximately 70-100 deg C when adding peat to the logging residue- and the willow fuel. The increased level of calcium in the inner bed particle layer caused by the added reactive calcium from the peat and/or removing alkali in the gas phase to a less reactive particular form via sorption and/or reaction with reactive peat ash (containing calcium, silica etc.) during which larger particles (>1{mu}m) are formed where collected potassium is present in a less reactive form, is considered to be the dominated reason for the increased agglomeration temperatures during combustion of logging residues and willow. During straw combustion, the ash forming matter were found as individual ash sticky particles in the bed. The iron, sulphur and calcium content of these individual ash particles were significantly increased when adding peat to the fuel mix thereby decreasing the stickiness of these particles i.e. reducing the agglomeration tendencies. Adding peat to the relatively silicon-poor fuels (willow and logging residues) resulted in higher slagging tendencies, especially when the relative silicon rich peat fuel (Brunnskoelen) was used. However, when co-combusting peat with the relatively silicon and potassium

  4. Improving methane production efficiency from biomass product gas via pressurized fluidized bed system%适宜增压流化床操作参数提高生物质热气化气合成甲烷效率

    Institute of Scientific and Technical Information of China (English)

    冯飞; 沈来宏; 肖军; 吕潇

    2015-01-01

    Natural gas is one of the clean primary energy sources and high-quality chemical raw materials. Technology of methane production from biomass thermo-chemical gasification (biomass-to-SNG) is one of the most important pathways to produce synthetic natural gas (SNG) to substitute diminishing natural gas. In the biomass-to-SNG process, the biomass is first converted into product gas through biomass gasification. Then, the product gas full of CO and H2is synthesized into methane through the methanation processes after some proper cleaning and conditioning processes. Finally, the crude synthetic natural gas is upgraded with CO2 removal and gas dehydration. In the whole biomass-to-SNG process, the methanation process of product gas is a key step. A pressurized fluidized bed methanation reactor system was designed and constructed, which is mainly composed of a main reactor and auxiliary equipments. An experimental study of methane production from product gas was carried out on this methantion reactor system with the commercial methanation catalyst as bed material. The Energy Dispersive Spectrometer analysis indicates that the methanation catalyst contains high nickel content and was squashed into small particles for the study. Then, the effects of methanation temperature, pressure, space velocity, and ratio of H2 to CO on the performance indexes (i.e. methane formation rate and CO conversion rate) were investigated. The results show that methane is efficiently produced on this pressurized fluidized bed methanation reactor system and the typical methane formation rate is higher than 3.2 mol/(L·h) while the CO conversion rate is more than 80%. Higher methanation temperature is favored to the methanation process and the methane formation rate and CO conversion rate achieve the maximum values at the methanation temperature about 350℃. However, when the methanation temperature is higher than 350℃, the methane formation rate and CO conversion rate decline slowly since the

  5. 固定床反应器中生物质/废塑料共热解制备燃料油%Co-pyrolysis of biomass and waste plastic for biofuel in fixed-bed reactor

    Institute of Scientific and Technical Information of China (English)

    徐艺; 陈宇; 华德润; 吴玉龙; 杨明德; 陈镇; 唐娜

    2013-01-01

    Thermal pyrolysis of different biomass (sawdust, straw) and plastic (polypropylene, poly vinyl chloride) and synergistic effects of co-pyrolysis of biomass and plastic were investigated with TGA. In fixed-bed reactor the influence of plastic content on co-pyrolysis of biomass and plastic was discussed, and the produced bio-oil was analyzed with elemental analysis and GC-MS. The results showed that significant synergy was present in the co-pyrolysis process of biomass and plastic, especially in the co-pyrolysis process of sawdust and polypropylene the synergistic effect was the most prominent. When the content of polypropylene was 80%, bio-oil yield was the highest, obviously higher than that of separate pyrolysis. And the results of elemental and GC-MS analysis showed that the bio-oil had a higher hydrogen content and its calorific value was equal to that of the crude oil equivalent.%通过热重分析不同生物质(木屑和秸秆)单独热解以及与塑料(PP和dcPVC)共热解时的热解行为,研究了生物质与塑料共热解过程中的协同作用.在固定床反应器中考察了塑料的含量对生物质/塑料共热解的影响,最后通过元素分析和GC-MS对所得生物油进行了分析.研究结果表明:生物质和塑料共热解过程中存在明显的协同作用.木屑和PP共热解过程中的协同作用最为显著,当PP含量为80%时,所得生物油的产率最高,明显高于两者单独热解得到的生物油.元素分析和GC-MS分析结果表明:木屑和PP所得生物油的含氢量较高,所得到生物油的热值与石化燃油的相近.

  6. Hydrogen production from high-moisture content biomass in supercritical water

    Energy Technology Data Exchange (ETDEWEB)

    Antal, M.J. Jr.; Matsumura, Y.; Onuma, M.T. [Univ. of Hawaii, Honolulu, HI (United States)] [and others

    1995-09-01

    Wet biomass (water hyacinth, banana trees, cattails, green algae, kelp, etc.) grows rapidly and abundantly around the world. However, wet biomass is not regarded as a promising feedstock for conventional thermochemical conversion processes because the cost of drying the material is too high. Prior work has shown that low concentrations of glucose (a model compound for whole biomass) and various wet biomass species (water hyacinth, algae) can be completely gasified in supercritical water at 600{degrees}C and 34.5 MPa after a 30 s residence time. But higher concentrations of glucose evidenced incomplete conversion. For this reason, flow reactors were fabricated which could accommodate packed beds of catalyst, and studies were initiated of the steam reforming (gasification) reactions in the presence of various candidate heterogeneous catalysts. The goal is to identify active catalysts for steam reforming biomass slurries in supercritical water. Soon after tests began, a suitable class of carbon-based catalysts was discovered. These catalysts effect complete (>99%) conversion of high-concentration glucose (up to 22% by weight) to a hydrogen-rich synthesis gas. High space velocities are realized [>20 (g/hr)/g], and the catalyst is stable over a period of several hours. The carbon catalyst is not expensive, and exists in a wide variety of forms and compositions. After this discovery, work has focused on four interrelated tasks: (1) tests to identify the most active form and composition of the catalyst; (2) tests employing the preferred catalyst to study the effect of feedstock composition on carbon conversion and gas composition; (3) studies of catalyst deactivation and subsequent reactivation, including the in-house synthesis of bifunctional catalysts which incorporate promoters and stabilizers; and (4) the design and fabrication of a larger, new reactor with a slurry feeder intended to handle high-concentration, wet biomass feeds.

  7. Entrained Flow Gasification of Biomass

    DEFF Research Database (Denmark)

    Qin, Ke

    of different fuels on syngas products was investigated at 1400 °C with steam addition. The yields of residual particulates (char and/or soot) decreased with increasing straw fraction during straw/wood co-gasification and with increasing biomass fraction (straw or wood) during biomass/coal co......, char-gas and soot-gas reactions, detailed gas-phase reactions, and mass and heat transfer. The model could reasonable predict the yields of syngas products obtained in the biomass gasification experiments. Moreover, the simulation results suggest that the soot can be completely converted and thereby......The present Ph. D. thesis describes experimental and modeling investigations on entrained flow gasification of biomass and an experimental investigation on entrained flow cogasification of biomass and coal. A review of the current knowledge of biomass entrained flow gasification is presented...

  8. Steam Reforming of Acetic Acid over Co-supported Catalysts: Coupling Ketonization for Greater Stability

    Energy Technology Data Exchange (ETDEWEB)

    Davidson, Stephen D.; Spies, Kurt A.; Mei, Donghai; Kovarik, Libor; Kutnyakov, Igor V.; Li, Xiaohong S.; Dagle, Vanessa; Albrecht, Karl O.; Dagle, Robert A.

    2017-09-11

    We report on the markedly improved stability of a novel 2-bed catalytic system, as compared to a conventional 1-bed steam reforming catalyst, for the production of H2 from acetic acid. The 2-bed catalytic system comprises of i) a basic oxide ketonization catalyst for the conversion of acetic acid to acetone, and a ii) Co-based steam reforming catalyst, both catalytic beds placed in sequence within the same unit operation. Steam reforming catalysts are particularly prone to catalytic deactivation when steam reforming acetic acid, used here as a model compound for the aqueous fraction of bio-oil. Catalysts comprising MgAl2O4, ZnO, CeO2, and activated carbon (AC) both with and without Co-addition were evaluated for conversion of acetic acid and acetone, its ketonization product, in the presence of steam. It was found that over the bare oxide support only ketonization activity was observed and coke deposition was minimal. With addition of Co to the oxide support steam reforming activity was facilitated and coke deposition was significantly increased. Acetone steam reforming over the same Co-supported catalysts demonstrated more stable performance and with less coke deposition than with acetic acid feedstock. DFT analysis suggests that over Co surface CHxCOO species are more favorably formed from acetic acid versus acetone. These CHxCOO species are strongly bound to the Co catalyst surface and could explain the higher propensity for coke formation from acetic acid. Based on these findings, in order to enhance stability of the steam reforming catalyst a dual-bed (2-bed) catalyst system was implemented. Comparing the 2-bed and 1-bed (Co-supported catalyst only) systems under otherwise identical reaction conditions the 2-bed demonstrated significantly improved stability and coke deposition was decreased by a factor of 4.

  9. Energy Recovery from Contaminated Biomass

    Directory of Open Access Journals (Sweden)

    Jiří Moskalík

    2012-01-01

    Full Text Available This study focuses on thermal gasification methods of contaminated biomass in an atmospheric fluidized bed, especially biomass contaminated by undesirable substances in its primary use. For the experiments, chipboard waste was chosen as a representative sample of contaminated biomass. In the experiments, samples of gas and tar were taken for a better description of the process of gasifying chipboard waste. Gas and tar samples also provide information about the properties of the gas that is produced.

  10. Chemical-looping gasification of biomass in a 10k Wth interconnected fluidized bed reactor using Fe2 O3/Al2 O3 oxygen carrier

    Institute of Scientific and Technical Information of China (English)

    HUSEYIN Sozen; WEI Guo-qiang; LI Hai-bin; HE Fang; HUANG Zhen

    2014-01-01

    The aim of this research is to design and operate a 10 kW hot chemical-looping gasification ( CLG) unit using Fe2 O3/Al2 O3 as an oxygen carrier and saw dust as a fuel. The effect of the operation temperature on gas composition in the air reactor and the fuel reactor, and the carbon conversion of biomass to CO2 and CO in the fuel reactor have been experimentally studied. A total 60 h run has been obtained with the same batch of oxygen carrier of iron oxide supported with alumina. The results show that CO and H2 concentrations are increased with increasing temperature in the fuel reactor. It is also found that with increasing fuel reactor temperature, both the amount of residual char in the fuel reactor and CO2 concentration of the exit gas from the air reactor are degreased. Carbon conversion rate and gasification efficiency are increased by increasing temperature and H2 production at 870 ℃reaches the highest rate. Scanning electron microscopy (SEM), X-ray diffraction (XRD) and BET-surface area tests have been used to characterize fresh and reacted oxygen carrier particles. The results display that the oxygen carrier activity is not declined and the specific surface area of the oxygen carrier particles is not decreased significantly.

  11. An Isothermal Steam Expander for an Industrial Steam Supplying System

    OpenAIRE

    Chen-Kuang Lin; Guang-Jer Lai; Yoshiyuki Kobayashi; Masahiro Matsuo; Min-Chie Chiu

    2015-01-01

    Steam is an essential medium used in the industrial process. To ensure steam quality, small and middle scale boilers are often adopted. However, because a higher steam pressure (compared to the necessary steam pressure) is generated, the boiler’s steam pressure will be reduced via a pressure regulator before the steam is directed through the process. Unfortunately, pressure is somewhat wasted during the reducing process. Therefore, in order to promote energy efficiency, a pressure regulator i...

  12. Biomass co-firing

    DEFF Research Database (Denmark)

    Yin, Chungen

    2013-01-01

    Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized-bed combus......Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized......-bed combustion (FBC) systems, and grate-firing systems, which are employed in about 50%, 40% and 10% of all the co-firing plants, respectively. Their basic principles, process technologies, advantages, and limitations are presented, followed by a brief comparison of these technologies when applied to biomass co...

  13. Biomass co-firing

    DEFF Research Database (Denmark)

    Yin, Chungen

    2013-01-01

    Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized-bed combus......Co-firing biomass with fossil fuels in existing power plants is an attractive option for significantly increasing renewable energy resource utilization and reducing CO2 emissions. This chapter mainly discusses three direct co-firing technologies: pulverized-fuel (PF) boilers, fluidized......-bed combustion (FBC) systems, and grate-firing systems, which are employed in about 50%, 40% and 10% of all the co-firing plants, respectively. Their basic principles, process technologies, advantages, and limitations are presented, followed by a brief comparison of these technologies when applied to biomass co...

  14. High-temperature entrained flow gasification of biomass

    DEFF Research Database (Denmark)

    Qin, Ke; Lin, Weigang; Jensen, Peter Arendt

    2012-01-01

    Biomass (wood and straw) gasification has been studied in a laboratory scale atmospheric pressure entrained flow reactor. Effects of reaction temperature, steam/carbon molar ratio, excess air ratio, and biomass type on the solid, liquid and gas products were investigated. The biomass was completely...

  15. Biomass power for rural development. Revised design report.

    Energy Technology Data Exchange (ETDEWEB)

    Neuhauser, Edward

    1999-10-03

    The retrofit of Dunkirk Steam Station to fire biomass fuels is an important part of the Consortium's goal--demonstrating the viability of commercial scale willow energy crop production and conversion to power. The goal for th biomass facilities at Dunkirk is to reliably cofire a combination of wood wastes and willow biomass with coal at approximately 20% by heat input.

  16. Operating Experience from two new Biomass Fired FBC-Plants

    Energy Technology Data Exchange (ETDEWEB)

    Bolhar-Nordenkampf, M.; Tschanun, I.; Kaiser, S. [Austrian Energy and Environment AG, Vienna (Austria)

    2006-07-15

    The use of renewable fuels in industrial power plants is rising continuously. The driving forces are the Kyoto protocol for CO{sub 2} reduction resulting in government support for green power electricity, substitution of imported primary energy and multi-fuel concepts together with RDF. Biomass fuel exists in various forms, traditionally as wood, bark, harvesting residues sewage sludge and organic waste. A favourable combustion technology is Austrian Energy's 'ECOFLUID' bubbling fluidized bed. Advantageous is the principle of a substoichiometric bed operation which allows bed temperature control in the range between 650 deg C - 850 deg C. Therefore, also fuel with low ash melting temperature can be burned. The applied staged combustion concept results in a homogenous temperature profile in the furnace and first pass of the boiler and thus low NO{sub x} emission. One new plant, owned by Energie AG in Timelkam/Austria has been commissioned in winter 2005. The main fuel of this 57 t/h boiler is bark, wood residues and waste wood up to 30% of the total thermal capacity. Grinding dust and saw dust can be co-fired, too. Optionally, sludge and animal wastes can be fired. The boiler is designed for 42 barg at live steam temperature of 440 deg C. The other new 30 MW{sub th} plant, owned by M-real Hallein AG in Hallein/Austria has been commissioned in winter 2005, too. The boiler is fired with wood chips, bark, rejects and other paper mill residues and furthermore it is able to burn the sludge of the mills own waste water treatment plant. Beside the boiler works as a post combustion system for exhaust gases from a 1 MW Biogas Otto-Engine, or alternatively it is able to burn the biogas directly. The boiler is designed for 61 barg at live steam temperature of 450 deg C.

  17. Method for producing ethanol and co-products from cellulosic biomass

    Science.gov (United States)

    Nguyen, Quang A

    2013-10-01

    The present invention generally relates to processes for production of ethanol from cellulosic biomass. The present invention also relates to production of various co-products of preparation of ethanol from cellulosic biomass. The present invention further relates to improvements in one or more aspects of preparation of ethanol from cellulosic biomass including, for example, improved methods for cleaning biomass feedstocks, improved acid impregnation, and improved steam treatment, or "steam explosion."

  18. Safety Picks up "STEAM"

    Science.gov (United States)

    Roy, Ken

    2016-01-01

    This column shares safety information for the classroom. STEAM subjects--science, technology, engineering, art, and mathematics--are essential for fostering students' 21st-century skills. STEAM promotes critical-thinking skills, including analysis, assessment, categorization, classification, interpretation, justification, and prediction, and are…

  19. Effect of biomass-sulfur interaction on ash composition and agglomeration for the co-combustion of high-sulfur lignite coals and olive cake in a circulating fluidized bed combustor.

    Science.gov (United States)

    Varol, Murat; Atimtay, Aysel T

    2015-12-01

    This study aimed to investigate the effect of biomass-sulfur interaction on ash composition and agglomeration for the co-combustion of high-sulfur lignite coals and olive cake in a circulating fluidized bed combustor. The tests included co-combustion of 50-50% by wt. mixtures of Bursa-Orhaneli lignite+olive cake and Denizli-Kale lignite+olive cake, with and without limestone addition. Ash samples were subjected to XRF, XRD and SEM/EDS analyses. While MgO was high in the bottom ash for Bursa-Orhaneli lignite and olive cake mixture, Al2O3 was high for Denizli-Kale lignite and olive cake mixture. Due to high Al2O3 content, Muscovite was the dominant phase in the bottom ash of Denizli Kale. CaO in the bottom ash has increased for both fuel mixtures due to limestone addition. K was in Arcanite phase in the co-combustion test of Bursa/Orhaneli lignite and olive cake, however, it mostly appeared in Potassium Calcium Sulfate phase with limestone addition.

  20. An Isothermal Steam Expander for an Industrial Steam Supplying System

    Directory of Open Access Journals (Sweden)

    Chen-Kuang Lin

    2015-01-01

    Full Text Available Steam is an essential medium used in the industrial process. To ensure steam quality, small and middle scale boilers are often adopted. However, because a higher steam pressure (compared to the necessary steam pressure is generated, the boiler’s steam pressure will be reduced via a pressure regulator before the steam is directed through the process. Unfortunately, pressure is somewhat wasted during the reducing process. Therefore, in order to promote energy efficiency, a pressure regulator is replaced by a steam expander. With this steam expander, the pressure will be transformed into mechanical energy and extracted during the expansion process. A new type of isothermal steam expander for an industrial steam supplying system will be presented in the paper. The isothermal steam expander will improve the energy efficiency of a traditional steam expander by replacing the isentropic process with an isothermal expansion process. With this, steam condensation will decrease, energy will increase, and steam quality will be improved. Moreover, the mathematical model of the isothermal steam expander will be established by using the Schmidt theory, the same principle used to analyze Stirling engines. Consequently, by verifying the correctness of the theoretical model for the isothermal steam expander using experimental data, a prototype of 100 c.c. isothermal steam expander is constructed.

  1. CFD modelling of an open core downdraft moving bed biomass gasifier; Modelado de un gasificador estratificado de lecho movil de biomasa, utilizando CFD

    Energy Technology Data Exchange (ETDEWEB)

    Rogel-Ramirez, A [Universidad Nacional Autonoma de Mexico, Mexico, D.F. (Mexico)]. E-mail: ARogelR@iingen.unam.mx

    2008-10-15

    This paper contains the description of a bidimensional Computational Fluid Dynamics (CFD), model Developer to simulate the flow and reaction in a stratified downdraft biomass gasifier, whereby Eulerian conservation equations are solved for particle and gas phase components, velocities and specific enthalpies. The model is based on the PHOENICS package and represents a tool which can be used in gasifier analysis and design. Contributions of chemical kinetics and the mixing rate using the EBU approach are considered in the gas phase global homogeneous reactions. The harmonic blending of chemical kinetics and mass transfer effects, determine the global heterogeneous reactions between char and O{sub 2}, CO{sub 2} and H{sub 2}O. The turbulence effect in the gas phase is accounted by the standard {kappa}-{epsilon} approach. The model provides information of the producer gas composition, velocities and temperature at the outlet, and allows different operating parameters and feed properties to be changed. Finally, a comparison with experimental data available in literature was done, which showed satisfactory agreement from a qualitative point of view, though further validation is required. [Spanish] Este estudio describe un modelo numerico bidimensional, basado en Dinamica de Fluidos Computacional (CFD), desarrollado para simular el flujo y las reacciones que ocurren en un gasificador estratificado de flujos paralelos, en el que se resuelven ecuaciones de conservacion Eulerianas para los componentes de la fase gaseosa, la fase solida, velocidades y entalpias especificas. El modelo esta basado en el codigo PHOENICS y representa una herramienta que puede ser utilizada en el analisis y diseno de gasificadores. En las reacciones globales homogeneas se consideran las contribuciones de la cinetica quimica y la rapidez de mezclado, usando el modelo Eddy Brake-UP (EBU). La medida harmonica de la cinetica quimica y la transferencia de masa, determinan las velocidades globales de

  2. Co-gasification of sewage sludge and woody biomass in a fixed-bed downdraft gasifier: toxicity assessment of solid residues.

    Science.gov (United States)

    Rong, Le; Maneerung, Thawatchai; Ng, Jingwen Charmaine; Neoh, Koon Gee; Bay, Boon Huat; Tong, Yen Wah; Dai, Yanjun; Wang, Chi-Hwa

    2015-02-01

    As the demand for fossil fuels and biofuels increases, the volume of ash generated will correspondingly increase. Even though ash disposal is now strictly regulated in many countries, the increasing volume of ash puts pressure on landfill sites with regard to cost, capacity and maintenance. In addition, the probability of environmental pollution from leakage of bottom ash leachate also increases. The main aim of this research is to investigate the toxicity of bottom ash, which is an unavoidable solid residue arising from biomass gasification, on human cells in vitro. Two human cell lines i.e. HepG2 (liver cell) and MRC-5 (lung fibroblast) were used to study the toxicity of the bottom ash as the toxins in the bottom ash may enter blood circulation by drinking the contaminated water or eating the food grown in bottom ash-contaminated water/soil and the toxic compounds may be carried all over the human body including to important organs such as lung, liver, kidney, and heart. It was found that the bottom ash extract has a high basicity (pH = 9.8-12.2) and a high ionic strength, due to the presence of alkali and alkaline earth metals e.g. K, Na, Ca and Mg. Moreover, it also contains concentrations of heavy metals (e.g. Zn, Co, Cu, Fe, Mn, Ni and Mo) and non-toxic organic compounds. Although human beings require these trace elements, excessive levels can be damaging to the body. From the analyses of cell viability (using MTS assay) and morphology (using fluorescence microscope), the high toxicity of the gasification bottom ash extract could be related to effects of high ionic strength, heavy metals or a combination of these two effects. Therefore, our results suggest that the improper disposal of the bottom ash wastes arising from gasification can create potential risks to human health and, thus, it has become a matter of urgency to find alternative options for the disposal of bottom ash wastes. Copyright © 2014 Elsevier Ltd. All rights reserved.

  3. Effect of Operating Conditions on Catalytic Gasification of Bamboo in a Fluidized Bed

    Directory of Open Access Journals (Sweden)

    Thanasit Wongsiriamnuay

    2013-01-01

    Full Text Available Catalytic gasification of bamboo in a laboratory-scale, fluidized bed reactor was investigated. Experiments were performed to determine the effects of reactor temperature (400, 500, and 600°C, gasifying medium (air and air/steam, and catalyst to biomass ratio (0 : 1, 1 : 1, and 1.5 : 1 on product gas composition, H2/CO ratio, carbon conversion efficiency, heating value, and tar conversion. From the results obtained, it was shown that at 400°C with air/steam gasification, maximum hydrogen content of 16.5% v/v, carbon conversion efficiency of 98.5%, and tar conversion of 80% were obtained. The presence of catalyst was found to promote the tar reforming reaction and resulted in improvement of heating value, carbon conversion efficiency, and gas yield due to increases in H2, CO, and CH4. The presence of steam and dolomite had an effect on the increasing of tar conversion.

  4. Pure hydrogen from pyrolysis oil by the steam-iron process

    NARCIS (Netherlands)

    Bleeker, M.F.

    2009-01-01

    The steam-iron process is an old process, which was used for the production of hydrogen from cokes at the beginning of the twentieth century. In this thesis the steam-iron process is used to produce pure hydrogen from pyrolysis oil. Pyrolysis oil, obtained from the pyrolysis of biomass, is used to

  5. Kinetics examination of pressurised steam gasification of beech wood

    Directory of Open Access Journals (Sweden)

    Grzywacz Przemysław

    2016-01-01

    Full Text Available In Poland, among all renewable energy sources, share of biomass in electricity production is the largest. Great potential in biomass utilization involves use of gasification technology. The course of biomass gasification process in steam atmosphere is the subject of numerous scientific studies. The aim of this study was kinetics examination of pressurized beech wood waste gasification, that can be successfully used in industrial gasification. Measurements were carried out on a unique laboratory installation, that allows kinetics examination of solid fuels gasification with steam at wide range of pressures, via using thermovolumetric method. Formation rates of main gaseous products were determined, moreover, composition of post-reaction gas, as well as biomass conversion degree depending on the temperature were specified. Kinetic parameters of gasification were calculated and series of kinetic models were used to their designation ie Isoconvesional method, Integrated Core Model (ICM, Grain Model (GM and Random Pore Model (RPM.

  6. Solar steam generation: Steam by thermal concentration

    Science.gov (United States)

    Shang, Wen; Deng, Tao

    2016-09-01

    The solar-driven generation of water steam at 100 °C under one sun normally requires the use of optical concentrators to provide the necessary energy flux. Now, thermal concentration is used to raise the vapour temperature to 100 °C without the need for costly optical concentrators.

  7. Ukraine Steam Partnership

    Energy Technology Data Exchange (ETDEWEB)

    Gurvinder Singh

    2000-02-15

    The Ukraine Steam Partnership program is designed to implement energy efficiency improvements in industrial steam systems. These improvements are to be made by the private plants and local government departments responsible for generation and delivery of energy to end-users. One of the activities planned under this program was to provide a two-day training workshop on industrial steam systems focusing on energy efficiency issues related to the generation, distribution, and consumption of steam. The workshop was geared towards plant managers, who are not only technically oriented, but are also key decision makers in their respective companies. The Agency for Rational Energy Use and Ecology (ARENA-ECO), a non-governmental, not-for-profit organization founded to promote energy efficiency and environmental protection in Ukraine, in conjunction with the Alliance staff in Kiev sent out invitations to potential participants in all the regions of Ukraine. The purpose of this report is the describe the proceedings from the workshop and provide recommendations from the workshop's roundtable discussion. The workshop was broken down into two main areas: (1) Energy efficient boiler house steam generation; and Energy efficient steam distribution and consumption. The workshop also covered the following topics: (1) Ukrainian boilers; (2) Water treatment systems; (3) A profile of UKRESCO (Ukrainian Energy Services Company); (4) Turbine expanders and electricity generation; (5) Enterprise energy audit basics; and (6) Experience of steam use in Donetsk oblast.

  8. Steam generator tube failures

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, P.E.; Shah, V.N.; Ward, L.W.; Ellison, P.G.

    1996-04-01

    A review and summary of the available information on steam generator tubing failures and the impact of these failures on plant safety is presented. The following topics are covered: pressurized water reactor (PWR), Canadian deuterium uranium (CANDU) reactor, and Russian water moderated, water cooled energy reactor (VVER) steam generator degradation, PWR steam generator tube ruptures, the thermal-hydraulic response of a PWR plant with a faulted steam generator, the risk significance of steam generator tube rupture accidents, tubing inspection requirements and fitness-for-service criteria in various countries, and defect detection reliability and sizing accuracy. A significant number of steam generator tubes are defective and are removed from service or repaired each year. This wide spread damage has been caused by many diverse degradation mechanisms, some of which are difficult to detect and predict. In addition, spontaneous tube ruptures have occurred at the rate of about one every 2 years over the last 20 years, and incipient tube ruptures (tube failures usually identified with leak detection monitors just before rupture) have been occurring at the rate of about one per year. These ruptures have caused complex plant transients which have not always been easy for the reactor operators to control. Our analysis shows that if more than 15 tubes rupture during a main steam line break, the system response could lead to core melting. Although spontaneous and induced steam generator tube ruptures are small contributors to the total core damage frequency calculated in probabilistic risk assessments, they are risk significant because the radionuclides are likely to bypass the reactor containment building. The frequency of steam generator tube ruptures can be significantly reduced through appropriate and timely inspections and repairs or removal from service.

  9. Hydrothermal pretreatment of biomass for pellet production

    Energy Technology Data Exchange (ETDEWEB)

    Tooyserkani, Z. [British Columbia Univ., Vancouver, BC (Canada). Clean Energy Research Centre, Biomass and Bioenergy Research Group

    2010-07-01

    This presentation discussed innovative technologies for the production of wood pellets using the hydrothermal pre-treatment of biomass. Conventional techniques use low-cost mill residues, such as saw dust and shavings, as feedstock to produce durable, low-ash pellets. However, mill residues are becoming less available as a result of fewer saw mills, increased pellet production, and increased competition for saw dust. Advanced techniques use mixed biomass such as logging residue as feedstock, creating pellets that are durable for handling and long-term storage, of a higher energy density for transport and mixing with coal for co-firing, and a choice feedstock for biofuels. Advanced pellet production uses steam explosion/pre-treatment in which biomass receives a short-term high-pressure steam treatment followed by sudden decompression. Mild torrefaction seems to have positive feedback, and steam-treated pellets are durable with superior hydrophobicity. 3 figs., 3 tabs.

  10. Cleaning of biomass derived product gas for engine applications and for co-firing in PC-boilers

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Staahlberg, P.; Laatikainen-Luntama, J. [VTT Energy, Espoo (Finland). Energy Production Technologies] [and others

    1997-10-01

    The conventional fluidized-bed combustion has become commercially available also to relatively small scale (5 MWe), but this technology has rather low power-to-heat ratio and consequently it`s potential is limited to applications where district or process heat is the main product. Thus, there seems to be a real need to develop more efficient methods for small-scale power production from biomass. Gasification diesel power plant is one alternative for the small-scale power production, which has clearly higher power-to-heat ratio than can be reached in conventional steam cycles. The main technical problem in this process is the gas cleaning from condensable tars. In addition to the diesel-power plants, there are several other interesting applications for atmospheric-pressure clean gas technology. One alternative for cost-effective biomass utilization is co-firing of biomass derived product gas in existing pulverized coal fired boilers (or other types of boilers and furnaces). The aim of the project is to develop dry gas cleaning methods for gasification-diesel power plants and for other atmospheric-pressure applications of biomass and waste gasification. The technical objectives of the project are as follows: To develop and test catalytic gas cleaning methods for engine. To study the removal of problematic ash species of (CFE) gasification with regard to co-combustion of the product gas in PC boilers. To evaluate the technical and economical feasibility of different small-scale power plant concepts based on fixed-bed updraft and circulating fluidized- bed gasification of biomass and waste. (orig.)

  11. Gasification and pyrolysis of different biomasses in lab scale system: A comparative study

    Directory of Open Access Journals (Sweden)

    Gądek W.

    2016-01-01

    Full Text Available Gasification and pyrolysis are very promising technologies for clean energy production especially from low rank fuels. Biomass and wastes with high chlorine, alkali and even heavy metals content are fuels preferential for thermal utilization. However, several problems during combustion in conventional steam boilers occurs e.g. slagging, fouling, chlorine corrosion, boiler efficiency deterioration. New efficient and cost effective technologies are needed, even in small-scale applications. The main objective of this work was to compare the thermochemical behaviour and process parameters effects of different biomass under air gasification and pyrolysis conditions. Three important fuels for European power industry were selected: woody biomass and two residual biomass, such as oat straw and dried citrus wastes. In order to evaluate the possibility to use different feedstocks or to combine and/or integrate them in thermochemical processes, a comparison among typical and untypical feedstocks is needed. Tests performed on small scale fixed bed reactor show the gas yield, its composition and LHV parameter. The results were performed in Royal Institute of Technology (KTH in Sweden during BRISK program (Biofuels Research Infrastructure for Sharing Knowledge.

  12. Hydrogen production from lignocellulosic biomass by two-step gasification method

    Energy Technology Data Exchange (ETDEWEB)

    Lee, In-Gu [Korea Institute of Energy Research (Korea, Republic of)

    2010-07-01

    Hydrogen can be produced from woody biomass by conventional gasification methods such as partial oxidation or steam gasification. Since these methods produce gas products with low content of hydrogen as well as high content of tar from gasification reactors, posttreatment processes including tar cracker and water-gas shift reaction process are usually necessary for obtaining clean hydrogen-rich gas from woody biomass. In this work, a twostep gasification method was experimentally studied as an alternative to the conventional methods. The first step of the gasification is the fast pyrolysis of biomass to obtain liquid-phase product (bio-oil) and the second step is to gasify the bio-oil to hydrogen-rich gas in supercritical water. The fast pyrolysis of woody biomass was carried out using a bench-scale fluidized-bed reactor. The gasification of bio-oil in supercritical water was performed using a continuous-flow reactor packed with catalyst. The effect of major reaction conditions such as temperature and catalyst on hydrogen yield will be discussed. (orig.)

  13. Diesel power plants based on biomass gasification. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Staahlberg, P.; Solantausta, Y.; Wilen, C.

    1996-12-31

    The aim of the project was to assess the competitiveness and market potential of small-scale power plant concepts based on biomass gasification and on diesel/gas engines, and to study the effect of process parameters on the efficiency of the circulating fluidized-bed gasifier and on the formation of tarry impurities. Alternative diesel/gas engine power plant concepts based on gasification in scale 6-50 MW{sub e} were assessed. In the basic version, where the electricity is generated only by the a diesel/gas engine, the efficiency level of 37 % is achieved in power generation. When steam cycle is added to the process the efficiency of power generation increases to 44-48 %. The efficiencies achieved in the process are very high compared with those of biomass power plant processes on a commercial level or under development. The most significant potential of biomass-based power generation is made up by wastes of sugar industries in south and Central America and in Asia. There are also very extensive growth potentials of bioenergy use in the NAFTA countries (USA, Canada and Mexico) and in Europe. In Europe, the bioenergy use is expected to grow most sharply in Italy, Spain, Germany and Poland. Carbon conversion obtained in the gasifier was in the range of 99.0-99.9 % for sawdust and 96-98 % for forest residue chips. The tar content of the product gas 10-15 g/m- m{sup 3}{sub n}, for sawdust in the gasification temperature of 830-930 deg C and with sand as circulating fluid-bed. When dolomite was used as circulating fluid-bed, the tar contents were 2-3 g/m{sup 3}{sub n} at as low temperatures as 880-890 deg C. The tar content of gas can be reduced sharply by phasing of gasification air and by using catalytic circulating fluid-bed material Bioenergy Research Programme; LIEKKI 2 Research Programme. 26 refs., 40 figs.

  14. Effect of Steam Explosion Pretreatment on Bamboo for Enzymatic Hydrolysis and Ethanol Fermentation

    Directory of Open Access Journals (Sweden)

    Zhiqiang Li

    2014-12-01

    Full Text Available Based on the steam explosion pretreatment that has been applied to other types of lignocellulosic biomass, the steam explosion pretreatment of bamboo, along with a study of the chemical compositions and enzymatic hydrolyzability of substrates, was conducted. The results show that steam explosion pretreatment can greatly enhance the cellulose-to-glucose conversion yield after enzymatic hydrolysis, which is sometimes affected by bamboo age and steam explosion conditions. When the steam explosion pretreatment conditions were 2.0 MPa (pressure and 4 min (time, the cellulose-to-glucose conversion yield of 2-year-old bamboo substrate was 62.5%. However, the cellulose-to-glucose conversion yield of bamboo substrates after direct (without steam explosion pretreatment sodium chlorite/acetic acid delignification was 93.1%. Fermentation of enzymatic hydrolyzates with Saccharomyces cerevisiae resulted in about 88.1% to 96.2% of the corresponding theoretical ethanol yield after 24 h.

  15. Viability study for application of combined reheater cycle (CRC) to fluidized bed combustion plants; Estudio de Viabilidad para la Aplicacion del Ciclo de Recalentamiento Combinado (CRC) a Plantas de Combustion de Lecho Fuido Atmosferico

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-01

    Basically, the project try to analyze the application viability of a first reheating in steam cycles of little power plants, useful mainly for biomass and wastes, in our case with coal blends; and a second reheating of the steam in conventional and fluidized bed combustion plants. Using in both cases the thermic energy of the exhaust gases from one gas turbine. The advantages of the CRC cycle are: (1) Reduction of the moisture in the turbine, increasing the energy efficiency and blade protection. (2) To take advantage of the waste gas energy from the gas turbine in optimum way. (3) Great operation flexibility under good efficiency results. In general, the system can use the synergy between gas, coal and waste energies with the highest global efficiency. (Author)

  16. Process for the treatment of lignocellulosic biomass

    Science.gov (United States)

    Dale, Bruce E.

    2014-07-08

    A process for the treatment of biomass to render structural carbohydrates more accessible and/or digestible using concentrated ammonium hydroxide with or without anhydrous ammonia addition, is described. The process preferably uses steam to strip ammonia from the biomass for recycling. The process yields of monosaccharides from the structural carbohydrates are good, particularly as measured by the enzymatic hydrolysis of the structural carbohydrates. The monosaccharides are used as animal feeds and energy sources for ethanol production.

  17. Process for the treatment of lignocellulosic biomass

    Science.gov (United States)

    Dale, Bruce E.; Lynd, Lee R.; Laser, Mark

    2013-03-12

    A process for the treatment of biomass to render structural carbohydrates more accessible and/or digestible using concentrated ammonium hydroxide with or without anhydrous ammonia addition, is described. The process preferably uses steam to strip ammonia from the biomass for recycling. The process yields of monosaccharides from the structural carbohydrates are good, particularly as measured by the enzymatic hydrolysis of the structural carbohydrates. The monosaccharides are used as animal feeds and energy sources for ethanol production.

  18. High performance steam development

    Energy Technology Data Exchange (ETDEWEB)

    Duffy, T.; Schneider, P. [Solar Turbines Inc., San Diego, CA (United States)

    1995-10-01

    Over 30 years ago U.S. industry introduced the world`s highest temperature (1200{degrees}F at 5000 psig) and most efficient power plant, the Eddystone coal-burning steam plant. The highest alloy material used in the plant was 316 stainless steel. Problems during the first few years of operation caused a reduction in operating temperature to 1100{degrees}F which has generally become the highest temperature used in plants around the world. Leadership in high temperature steam has moved to Japan and Europe over the last 30 years.

  19. STEAM GENERATOR GROUP PROJECT

    Energy Technology Data Exchange (ETDEWEB)

    Clark, R. A.; Lewis, M

    1985-09-01

    This report is a summary of progress in the Surry Steam Generator Group Project for 1984. Information is presented on the analysis of two baseline eddy current inspections of the generator. Round robin series of tests using standard in-service inspection techniques are described along with some preliminary results. Observations are reported of degradation found on tubing specimens removed from the generator, and on support plates characterized in-situ. Residual stresses measured on a tubing specimen are reported. Two steam generator repair demonstrations are described; one for antivibration bar replacement, and one on tube repair methods. Chemical analyses are shown for sludge samples removed from above the tube sheet.

  20. 浆态床反应器中生物质合成气合成二甲醚的研究%DME synthesis from biomass-derived syngas in a slurry-bed reactor

    Institute of Scientific and Technical Information of China (English)

    马俊国; 葛庆杰; 马现刚; 徐恒泳

    2012-01-01

    Dimethyl ether (DME) synthesis from biomass-derived syngas in a slurry-bed reactor was investigated over a hybrid catalyst composed of methanol synthesis catalyst and molecular sieve. The results showed that the catalyst containing SAPO-11 exhibits higher DME selectivity and catalytic stability, which is closely related to the weak acidity of SAPO-11 in the hybrid catalysts. 40% CO conversion and 95% DME selectivity in organic products could be kept during 35 h stability test over the hybrid catalyst when the weight ratio of methanol synthesis catalyst to SAPO-11 was 3.%进行了浆态床反应器中,甲醇合成催化剂与分子筛混合制复合催化剂上,生物质制取的合成气(简称生物质合成气)一步法合成二甲醚的研究,重点考察了不同脱水组分和工艺条件对催化剂反应性能的影响,同时,结合NH3 -TPD等手段对催化剂进行了表征.结果表明,含有较弱酸性SAPO-11分子筛的复合催化剂更适合生物质合成气原料气杂质多、氢碳比低的特点,在合成二甲醚反应中具有更高的选择性和稳定性.250℃、5 MPa、500 h-1时,在甲醇催化剂与SAPO-11分子筛比例为3∶1的复合催化剂上,合成气合成二甲醚反应35 h内,CO转化率稳定在40%以上,二甲醚在有机产品中的选择性保持在97%左右.

  1. Fuel gas production from renewable biomass in a circulating fluidized bed as a bases for zero-CO{sub 2} power generation in a combined-cycle power plant; Brenngaserzeugung aus nachwachsenden Biomassen in der zirkulierenden Wirbelschicht als Grundlage fuer eine CO{sub 2}-neutrale Stromerzeugung in einem GUD Kraftwerk

    Energy Technology Data Exchange (ETDEWEB)

    Albrecht, J.; Loeffler, J.; Hirschfelder, H. [Lurgi Energie und Umwelt GmbH, Frankfurt am Main (Germany)

    1996-12-31

    A pilot circulating fluidized bed plant in the range of 1.7 MW{sub th} has been operated successfully with fossil fuels, residues, wood bark and wood chips, reet grass and sorghum pellets. Depending on the specifications for product gas and fuel quality, air, oxygen-enriched air or oxygen/steam mixtures are used as gasification agents in the gas generator. (orig) [Deutsch] In einer ZWS-Pilotanlage mit ca. 1.7 MW thermischer Leistung wurden bisher ausser fossilen und Abfallbrennstoffen auch Rindenabfaelle, Holzschnitzel, Schilfgras und Sorghumpellets erfolgreich zur Brenngaserzeugung eingesetzt. Entsprechend den Anforderungen an das Produktgas und der Brennstoffqualitaet wird Luft, sauerstoffangereicherte Luft oder Sauerstoff/Dampfgemische als Vergasungsmittel im ZWS-Gaserzeuger eingesetzt. (orig)

  2. Novel Approach to Tar Removal from Biomass Producer Gas by Means of a Nickel-Based Catalyst

    Science.gov (United States)

    Vosecký, M.; Kameníková, P.; Pohořelý, M.; Skoblja, S.; Punčochář, M.

    The nickel-based catalyst was exposed to the raw gas from gasification of woody biomass with air in a fluidized-bed. After dust removal on a barrier filter and sulphur compounds capture, namely H2S, on an active sorbent made of CuO and ZnO, higher hydrocarbons as tar components were decomposed/reformed on aNi-catalyst. Steam reforming reactions led to decomposition of tar and all hydrocarbons higher than CH4 into mainly H2 and CO which further underwent reaction with steam via the water gas shift reaction to CO2. The reforming reactions caused approximately 10-20 % decrease in the lower heating values of the producer gas from the inlet values 5.0-6.5 MJ m-3. The gas yield increased fromvalues 2.4-2.6 m3 kg-1 to values 2.8-3.0 m3 kg-1 on dry biomass basis. The chosen tar removal concept based on combination of dolomite in the fluidized-bed with the secondary catalytic reactor was proved by 20 hours long experiment in which the finaltar content below 30 mg m-3 was attained corresponding to more than 97 % tar conversion. H2S content in producer gas was expected to be below 100 vol. ppm, bulk of which was captured on the sorbent. Only limited deactivation of thecatalyst by sulphur compounds was found in the front of the catalyst bed where sulphur content was determined as high as 173 wt. ppm compared to 22 wt. ppm in the fresh sample.

  3. Biomass pretreatment

    Science.gov (United States)

    Hennessey, Susan Marie; Friend, Julie; Elander, Richard T; Tucker, III, Melvin P

    2013-05-21

    A method is provided for producing an improved pretreated biomass product for use in saccharification followed by fermentation to produce a target chemical that includes removal of saccharification and or fermentation inhibitors from the pretreated biomass product. Specifically, the pretreated biomass product derived from using the present method has fewer inhibitors of saccharification and/or fermentation without a loss in sugar content.

  4. Steam pretreatment of dry and ensiled industrial hemp for ethanol production

    OpenAIRE

    Sipos, Bálint; Kreuger, Emma; Svensson, Sven-Erik; Réczey, Kati; Björnsson, Lovisa; Zacchi, Guido

    2010-01-01

    Abstract Biomass can be converted into liquid and gaseous biofuels with good efficiency. In this study, the conversion of industrial hemp (Cannabis sativa L.), a biomass source that can be cultivated with a high biomass yield per hectare, was used. Steam pretreatment of dry and ensiled hemp was investigated prior to ethanol production. The pretreatment efficiency was evaluated in terms of sugar recovery and polysaccharide conversion in the enzymatic hydrolysis step. For both materi...

  5. Hydrogen production from the co-utilisation of coal and biomass

    Energy Technology Data Exchange (ETDEWEB)

    J. Fermoso; B. Arias; C. Pevida; M.G. Plaza; F. Rubiera; J.J. Pis [Instituto Nacional del Carbon, CSIC, Oviedo (Spain). Department of Energy & Environment

    2007-07-01

    In this work, co-gasification and co-pyrolysis of binary blends of a bituminous coal (PT) and two types of biomass (olive stones, OS; chestnut, CH) were conducted at atmospheric pressure in a fixed bed reactor. Pyrolysis was performed under nitrogen, and gasification under steam/oxygen atmosphere. In the fixed bed reactor, the particles of the different fuels are in close contact, providing an optimum means for evaluating possible synergetic effects. Pyrolysis tests showed the lack of interaction between the components of the blend. Mass distribution and gases produced during the pyrolysis tests can be predicted from those of the individual components and their mass fractions. During the gasification tests, interactions between the components of the blends were observed. An increase of tar production above the theoretically calculated value, as the percentage of the biomass increased in the blends was observed. The gases produced during gasification of PT-OS blends followed the linear-additive rule, with the exception of CO{sub 2}. However, in the case of PT-CH blends, the main gases produced (CO{sub 2}, CO and H{sub 2}) deviated from the additive rule. 18 refs., 4 figs., 3 tabs.

  6. Advanced biomass gasification for high-efficiency power. Final activity report of BiGPower Project

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Kurkela, M. (eds.)

    2009-11-15

    The BiGPower project was related to the development of 2nd generation high-efficiency biomass-to-electricity technologies, which have the potential to meet the targets of cost effective electricity production from wide range of biomass and waste fuels in size ranges typical to locally available feedstock sources (below 100 MW{sub e}). This project was designed to create the fundamental and technical basis for successful future industrial developments and demonstration projects aiming to commercial breakthrough by 2010-2020. This overall aim was approached by carrying out in pre-competitive manner well-focused R and D activities on the key bottlenecks of advanced biomass gasification power systems. Three promising European gasification technologies in this target size range were selected to form the basis for the development: 1) air-blow novel fixed-bed gasifier for size range of 0.5-5 MWe, 2) steam gasification in a dual-fluidisedbed gasifier for 5-50 MWe and 3) air-blown pressurised fluidised-bed gasification technology for 5-100 MWe. In all biomass gasification processes, the product gas contains several types of gas contaminants, which have to be efficiently removed before utilising the gas in advanced power systems. The key technical solutions developed in the BiGPower project were: a) high-temperature catalytic removal of tars and ammonia by new catalytic methods, and b) development of innovative low cost gas filtration. Three most potential power production cycle alternatives were examined and developed: 1) gas engines, 2) molten carbonate fuel cells (MCFC) and 3) the simplified Integrated Gasification Combined Cycle (IGCC) process. The performance and techno-economic feasibility of these advanced gasification-topower concepts were examined by carrying out case studies in different European Union. (orig.)

  7. Fossil fuel savings, carbon emission reduction and economic attractiveness of medium-scale integrated biomass gasification combined cycle cogeneration plants

    Directory of Open Access Journals (Sweden)

    Kalina Jacek

    2012-01-01

    Full Text Available The paper theoretically investigates the system made up of fluidized bed gasifier, SGT-100 gas turbine and bottoming steam cycle. Different configurations of the combined cycle plant are examined. A comparison is made between systems with producer gas (PG and natural gas (NG fired turbine. Supplementary firing of the PG in a heat recovery steam generator is also taken into account. The performance of the gas turbine is investigated using in-house built Engineering Equation Solver model. Steam cycle is modeled using GateCycleTM simulation software. The results are compared in terms of electric energy generation efficiency, CO2 emission and fossil fuel energy savings. Finally there is performed an economic analysis of a sample project. The results show relatively good performance in the both alternative configurations at different rates of supplementary firing. Furthermore, positive values of economic indices were obtained. [Acknowledgements. This work was carried out within the frame of research project no. N N513 004036, titled: Analysis and optimization of distributed energy conversion plants integrated with gasification of biomass. The project is financed by the Polish Ministry of Science.

  8. Biomass recalcitrance

    DEFF Research Database (Denmark)

    Felby, Claus

    2009-01-01

    , enzymatic hydrolysis, and product fermentation options. Biomass Recalcitrance is essential reading for researchers, process chemists and engineers working in biomass conversion, also plant scientists working in cell wall biology and plant biotechnology. This book examines the connection between biomass...... - this collective resistance is known as "biomass recalcitrance." Breakthrough technologies are needed to overcome barriers to developing cost-effective processes for converting biomass to fuels and chemicals. This book examines the connection between biomass structure, ultrastructure, and composition......, to resistance to enzymatic deconstruction, with the aim of discovering new cost-effective technologies for biorefineries. It contains chapters on topics extending from the highest levels of biorefinery design and biomass life-cycle analysis, to detailed aspects of plant cell wall structure, chemical treatments...

  9. Biomass-Derived Hydrogen from a Thermally Ballasted Gasifier

    Energy Technology Data Exchange (ETDEWEB)

    Brown, Robert C

    2007-04-06

    The goal of this project is to develop an indirectly heated gasification system that converts switchgrass into hydrogen-rich gas suitable for powering fuel cells. The project includes investigations of the indirectly-heated gasifier, development of particulate removal equipment, evaluation of catalytic methods for upgrading producer gas, development of contaminant measurement and control techniques, modeling of the thermal performance of the ballasted gasifier, and estimation of the cost of hydrogen from the proposed gasification system. Specific technologies investigated include a thermally ballasted gasifier, a moving bed granular filter, and catalytic reactors for steam reforming and water-gas shift reaction. The approach to this project was to employ a pilot-scale (5 ton per day) gasifier to evaluate the thermally ballasted gasifier as a means for producing hydrogen from switchgrass. A slipstream from the gasifier was used to evaluate gas cleaning and upgrading options. Other tests were conducted with laboratory-scale equipment using simulated producer gas. The ballasted gasifier operated in conjunction with a steam reformer and two-stage water-gas shift reactor produced gas streams containing 54.5 vol-% H2. If purge gas to the feeder system could be substantially eliminated, hydrogen concentration would reach 61 vol-%, which closely approaches the theoretical maximum of 66 vol-%. Tests with a combined catalyst/sorbent system demonstrated that steam reforming and water-gas shift reaction could be substantially performed in a single reactor and achieve hydrogen concentrations exceeding 90 vol-%. Cold flow trials with a laboratory-scale moving bed granular filter achieved particle removal efficiencies exceeding 99%. Two metal-based sorbents were tested for their ability to remove H2S from biomass-derived producer gas. The ZnO sorbent, tested at 450° C, was effective in reducing H2S from 200 ppm to less than 2 ppm (>99% reduction) while tests with the MnO sorbent

  10. Steam Generator Group Project. Task 6. Channel head decontamination

    Energy Technology Data Exchange (ETDEWEB)

    Allen, R.P.; Clark, R.L.; Reece, W.D.

    1984-08-01

    The Steam Generator Group Project utilizes a retired-from-service pressurized-water-reactor steam generator as a test bed and source of specimens for research. An important preparatory step to primary side research activities was reduction of the radiation field in the steam generator channel head. This task report describes the channel head decontamination activities. Though not a programmatic research objective it was judged beneficial to explore the use of dilute reagent chemical decontamination techniques. These techniques presented potential for reduced personnel exposure and reduced secondary radwaste generation, over currently used abrasive blasting techniques. Two techniques with extensive laboratory research and vendors prepared to offer commercial application were tested, one on either side of the channel head. As indicated in the report, both techniques accomplished similar decontamination objectives. Neither technique damaged the generator channel head or tubing materials, as applied. This report provides details of the decontamination operations. Application system and operating conditions are described.

  11. [Low temperature plasma technology for biomass refinery].

    Science.gov (United States)

    Fu, Xiaoguo; Chen, Hongzhang

    2014-05-01

    Biorefinery that utilizes renewable biomass for production of fuels, chemicals and bio-materials has become more and more important in chemical industry. Recently, steam explosion technology, acid and alkali treatment are the main biorefinery treatment technologies. Meanwhile, low temperature plasma technology has attracted extensive attention in biomass refining process due to its unique chemical activity and high energy. We systemically summarize the research progress of low temperature plasma technology for pretreatment, sugar platflow, selective modification, liquefaction and gasification in biomass refinery. Moreover, the mechanism of low temperature plasma in biorefinery and its further development were also discussed.

  12. CFB gasification of biomass residues for co-combustion in large utility boilers studies on ash control and gas cleaning

    Energy Technology Data Exchange (ETDEWEB)

    Kurkela, E.; Moilanen, A.; Nieminen, M. [VTT Energy, Espoo (Finland)

    1999-07-01

    The woody residues of mechanical and chemical wood industry as well as other high-grade woody biofuels can be co-combusted with coal in existing fluidised- bed boilers or even in pulverised combustors without major problems. On the other hand, extensive full-scale test programmes carried out with straw in Denmark and with various agrobiofuels in the United States have clearly shown the limitations of this type of co-combustion methods. Many potential biomass feedstocks, such as straw, have a problematic ash melting behaviour, which causes sintering and fouling problems in combustors. Straw and many fast-growing energy crops as well as industrial and municipal waste fuels often contain high amounts of chlorine and alkali metals, which have a tendency to cause severe corrosion problems in coal-fired boilers. This problem can be assumed to be more severe in the modern plants where supercritical steam values are utilised. Perhaps the most critical factor controlling possibilities for direct co-firing of these problematic biofuels in large PC boilers is the usability of coal ash for cement industry and construction purposes. Demolition wood waste is another example of a locally important renewable feedstock, which is difficult to be introduced into ordinary coal-based combustion plants due to the relatively high content of heavy metals (Zn,Pb, Cd) and chlorine. In principle, there are three main technical solutions to avoid sintering, corrosion and ash problems in co-utilisation of problematic biofuels in large coal-fired power plants: Construction of a smaller separate boiler with low steam values for the biofuels and superheating the steam of the biomass boiler in the coal-fired boiler. Production of pyrolysis oils from the biomass, and Gasification of biomass and combustion of cleaned product gas in the boiler. The concept based on gasification has several advantages over the other alternatives. First of all the gasification reactor, bubbling or circulating fluidised-bed

  13. Biomass and waste gasification in pulverised coal-fired boilers

    Energy Technology Data Exchange (ETDEWEB)

    Nieminen, M.; Kurkela, E.; Palonen, J. [VTT Processes, Espoo (Finland)

    2004-07-01

    The replacement of coal in existing large pulverised coal-fired boilers is a cost-effective way to lower the CO{sub 2} emissions of power production. A power plant concept consisting of a gasifier connected to a large conventional boiler with a high efficiency steam cycle offers an attractive and efficient way house local biomass and waste sources in energy production. In the simplified concept clean biomass or waste is gasifier and gas is directly fed to PC boiler and co-combusted with coal. At Kymijarvi power plant in Lahti, Finland, 60 MW circulating fluidized bed gasifier was commissioned in early 1998 and has since then been in commercial operation replacing hard coal in a 360 MW{sub th} boiler producing power and district heat. The annual gasifier availability has been over 95% in each year and the Lahti plant has clearly demonstrated that the technology is technically proven and is able to reduce the emission of CO{sub 2}, SO{sub 2}, dust and NOx compared to coal-alone combustion. Contaminated biomass or waste fuels can also be utilised for replacing coal in large-scale PC boiler but most of the harmful contaminants have to be removed prior co-combustion of the gas. Product gas cleaning makes it possible to utilise even fuels with higher chlorine and metal contents. The dry gas cleaning methods have been tested at pilot scale and will be soon demonstrated in gasification plants designed for solid recovered fuels originating form household and industrial wastes. 5 refs., 4 figs., 5 tabs.

  14. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    张利斌; 李修伦

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39 mm ID and 2.0 m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum.The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  15. Boiling Heat Transfer in Circulating Fluidized Beds

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    A model is proposed to predict boiling heat transfer coefficient in a three-phase circulating fluidized bed (CFB), which is a new type of evaporation boiling means for enhancing heat transfer and preventing fouling. To verify the model, experiments are conducted in a stainless steel column with 39mm ID and 2.0m height, in which the heat transfer coefficient is measured for different superficial velocities, steam pressures, particle concentrations and materials of particle. As the steam pressure and particle concentrations increase, the heat transfer coefficient in the bed increases. The heat transfer coefficient increases with the liquid velocity but it exhibits a local minimum. The heat transfer coefficient is correlated with cluster renewed model and two-mechanism method. The prediction of the model is in good agreement with experimental data.

  16. Fast microwave-assisted catalytic gasification of biomass for syngas production and tar removal.

    Science.gov (United States)

    Xie, Qinglong; Borges, Fernanda Cabral; Cheng, Yanling; Wan, Yiqin; Li, Yun; Lin, Xiangyang; Liu, Yuhuan; Hussain, Fida; Chen, Paul; Ruan, Roger

    2014-03-01

    In the present study, a microwave-assisted biomass gasification system was developed for syngas production. Three catalysts including Fe, Co and Ni with Al2O3 support were examined and compared for their effects on syngas production and tar removal. Experimental results showed that microwave is an effective heating method for biomass gasification. Ni/Al2O3 was found to be the most effective catalyst for syngas production and tar removal. The gas yield reached above 80% and the composition of tar was the simplest when Ni/Al2O3 catalyst was used. The optimal ratio of catalyst to biomass was determined to be 1:5-1:3. The addition of steam was found to be able to improve the gas production and syngas quality. Results of XRD analyses demonstrated that Ni/Al2O3 catalyst has good stability during gasification process. Finally, a new concept of microwave-assisted dual fluidized bed gasifier was put forward for the first time in this study.

  17. BIOMASS PYROLYSIS FOR LIQUIDS IN CIRCULATING FLUIDIZED BED(CFB)REACTOR%循环流化床反应器固体生物质的热解液化

    Institute of Scientific and Technical Information of China (English)

    戴先文; 吴创之; 周肇秋; 陈勇

    2001-01-01

    介绍了以循环流化床反应器为主体的固体生物质热解液化装置,实验过程,实验结果及分析。通过对气体产物的比较及油产物一般物性和油成分的分析,得出如下结论:1)较高的温度和较长的停留时间会降低油的产率,生成过多的不凝气;过低的温度和加热速率导致严重的碳化,同样会降低油产率,本实验的最高油产率可达63%。2)生物质热解油品的物性特点主要包括水分含量较高,pH值较低,粘度变化范围很大,热值与化石燃料相比为低,并且油品中因含氧量很高而极不稳定,油品的组成成分非常复杂,烷烃和非烃占据了相当的比例,芳烃和沥青质含量相对较少。3)在循环流化床中的固体生物质热解液化可模化为热解区和还原裂解区。%With the CFB as main reactor,an integrated facility was developed for the fast pyrolysis of biomass.In this facility,the bed is divided into two zones according to the pyrolysis and secondary reactions,the main chemical processes can be modelled.Based on the variation of the pyrolysis gas composition and the bio-oil ingredients,analysis of the experimental data highlights the important effects of temperature,heating rate and residence time.The main trend is that the higher temperature and longer residence time would contribute to the secondary reaction and the lower heating rate favors the carbonization,which both reduce the liquid production.In this study,the best bio-oil yield is 63%in weight.The component analysis of bio-oil shows that most compounds in bio-oil are nonhydrocarbons,while alkanes,aromatics and bitumen are relatively low.The physical properties of bio-oil include the high water and oxygen content,and the low pH and LHV.

  18. Biomass recalcitrance

    DEFF Research Database (Denmark)

    Felby, Claus

    2009-01-01

    Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes - this co......Alternative and renewable fuels derived from lignocellulosic biomass offer a promising alternative to conventional energy sources, and provide energy security, economic growth, and environmental benefits. However, plant cell walls naturally resist decomposition from microbes and enzymes...... - this collective resistance is known as "biomass recalcitrance." Breakthrough technologies are needed to overcome barriers to developing cost-effective processes for converting biomass to fuels and chemicals. This book examines the connection between biomass structure, ultrastructure, and composition......, to resistance to enzymatic deconstruction, with the aim of discovering new cost-effective technologies for biorefineries. It contains chapters on topics extending from the highest levels of biorefinery design and biomass life-cycle analysis, to detailed aspects of plant cell wall structure, chemical treatments...

  19. INFLUENCE OF STEAM PRESSURE ON THE PHYSICO-CHEMICAL PROPERTIES OF DEGRADED HEMICELLULOSES OBTAINED FROM STEAM-EXPLODED LESPEDEZA STALKS

    Directory of Open Access Journals (Sweden)

    Kun Wang

    2010-06-01

    Full Text Available Steam explosion pretreatment was used to release hemicelluloses from the stalks of Lespedeza crytobotrya, a potential woody biomass crop. Hemicelluloses from Lespedeza crytobotrya subjected to five different pretreatment severities were extracted with 60% aqueous ethanol solution containing 1% NaOH, characterized by component analysis, gel permeation chromatography (GPC, FT-IR, NMR spectroscopy, and thermal analysis, and compared with hemicelluloses obtained from untreated stalks. It was found that the hemicellulosic fractions mainly consisted of arabinoxylans and β-glucans or xyloglucans. Steam explosion pretreatment yielded noticeable degradation and debranching reactions, illustrated by a linear decrease of molecular weight and Ara/Xyl ratio with increasing severity. For further high-value utilization of the hemicellulosic polymers, steam explosion at 20 or 22.5 kg/m2 for 4 min is promising because of improved extraction efficiency and avoidance of over-drastic degradation of the polymers.

  20. Wet steam wetness measurement in a 10 MW steam turbine

    Directory of Open Access Journals (Sweden)

    Kolovratník Michal

    2014-03-01

    Full Text Available The aim of this paper is to introduce a new design of the extinction probes developed for wet steam wetness measurement in steam turbines. This new generation of small sized extinction probes was developed at CTU in Prague. A data processing technique is presented together with yielded examples of the wetness distribution along the last blade of a 10MW steam turbine. The experimental measurement was done in cooperation with Doosan Škoda Power s.r.o.

  1. Wet steam wetness measurement in a 10 MW steam turbine

    OpenAIRE

    Kolovratník Michal; Bartoš Ondřej

    2014-01-01

    The aim of this paper is to introduce a new design of the extinction probes developed for wet steam wetness measurement in steam turbines. This new generation of small sized extinction probes was developed at CTU in Prague. A data processing technique is presented together with yielded examples of the wetness distribution along the last blade of a 10MW steam turbine. The experimental measurement was done in cooperation with Doosan Škoda Power s.r.o.

  2. NUCLA Circulating Atmospheric Fluidized Bed Demonstration Project

    Energy Technology Data Exchange (ETDEWEB)

    1992-02-01

    The objective of this DOE Cooperative Agreement is to conduct a cost-shared clean coal technology project to demonstrate the feasibility of circulating fluidized bed combustion technology and to evaluate economic, environmental, and operational benefits of CFB steam generators on a utility scale. At the conclusion of the Phase 2 program, testing related to satisfying these objectives was completed. Data analysis and reporting are scheduled for completion by October 1991. (VC)

  3. COMPARISON BETWEEN WET OXIDATION AND STEAM EXPLOSION AS PRETREATMENT METHODS FOR ENZYMATIC HYDROLYSIS OF SUGARCANE BAGASSE

    OpenAIRE

    Carlos Martín; Marcelo Marcet; Anne Belinda Thomsen

    2008-01-01

    Alkaline wet oxidation and steam explosion pretreatments of sugarcane bagasse were compared with regard to biomass fractionation, formation of by-products, and enzymatic convertibility of the pretreated material. Wet oxidation led to the solubilisation of 82% of xylan and 50% of lignin, and to a two-fold increase of cellulose content in the pretreated solids, while steam explosion solubilised only 60% of xylan and 35% of lignin and increased cellulose content in the solid material by one thir...

  4. Biogas from lignocellulosic biomass

    Energy Technology Data Exchange (ETDEWEB)

    Berglund Odhner, Peter; Schabbauer, Anna [Grontmij AB, Stockholm (Sweden); Sarvari Horvath, Ilona; Mohseni Kabir, Maryam [Hoegskolan i Boraas, Boraas (Sweden)

    2012-01-15

    Grontmij AB has cooperated with the University of Boraas to evaluate the technological and economical possibilities for biogas production from substrates containing lignocellulose, such as forest residues, straw and paper. The state of knowledge regarding biogas production from cellulosic biomass has been summarized. The research in the field has been described, especially focusing on pretreatment methods and their results on increased gas yields. An investigation concerning commercially available pretreatment methods and the cost of these technologies has been performed. An economic evaluation of biogas production from lignocellulosic materials has provided answers to questions regarding the profitability of these processes. Pretreatment with steam explosion was economically evaluated for three feedstocks - wood, straw and paper - and a combination of steam explosion and addition of NaOH for paper. The presented costs pertain to costs for the pretreatment step as it, in this study, was assumed that the pretreatment would be added to an existing plant and the lignocellulosic substrates would be part of a co-digestion process. The results of the investigation indicate that it is difficult to provide a positive net result when comparing the cost of pretreatment versus the gas yield (value) for two of the feedstocks - forest residues and straw. This is mainly due to the high cost of the raw material. For forest residues the steam pretreatment cost exceeded the gas yield by over 50 %, mainly due to the high cost of the raw material. For straw, the production cost was similar to the value of the gas. Paper showed the best economic result. The gas yield (value) for paper exceeded the pretreatment cost by 15 %, which makes it interesting to study paper further.

  5. Mobile Biomass Pelletizing System

    Energy Technology Data Exchange (ETDEWEB)

    Thomas Mason

    2009-04-16

    This grant project examines multiple aspects of the pelletizing process to determine the feasibility of pelletizing biomass using a mobile form factor system. These aspects are: the automatic adjustment of the die height in a rotary-style pellet mill, the construction of the die head to allow the use of ceramic materials for extreme wear, integrating a heat exchanger network into the entire process from drying to cooling, the use of superheated steam for adjusting the moisture content to optimum, the economics of using diesel power to operate the system; a break-even analysis of estimated fixed operating costs vs. tons per hour capacity. Initial development work has created a viable mechanical model. The overall analysis of this model suggests that pelletizing can be economically done using a mobile platform.

  6. Integrated Biomass Gasification with Catalytic Partial Oxidation for Selective Tar Conversion

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Lingzhi; Wei, Wei; Manke, Jeff; Vazquez, Arturo; Thompson, Jeff; Thompson, Mark

    2011-05-28

    requirement for commercial deployment of biomass-based power/heat co-generation and biofuels production. There are several commonly used syngas clean-up technologies: (1) Syngas cooling and water scrubbing has been commercially proven but efficiency is low and it is only effective at small scales. This route is accompanied with troublesome wastewater treatment. (2) The tar filtration method requires frequent filter replacement and solid residue treatment, leading to high operation and capital costs. (3) Thermal destruction typically operates at temperatures higher than 1000oC. It has slow kinetics and potential soot formation issues. The system is expensive and materials are not reliable at high temperatures. (4) In-bed cracking catalysts show rapid deactivation, with durability to be demonstrated. (5) External catalytic cracking or steam reforming has low thermal efficiency and is faced with problematic catalyst coking. Under this program, catalytic partial oxidation (CPO) is being evaluated for syngas tar clean-up in biomass gasification. The CPO reaction is exothermic, implying that no external heat is needed and the system is of high thermal efficiency. CPO is capable of processing large gas volume, indicating a very compact catalyst bed and a low reactor cost. Instead of traditional physical removal of tar, the CPO concept converts tar into useful light gases (eg. CO, H2, CH4). This eliminates waste treatment and disposal requirements. All those advantages make the CPO catalytic tar conversion system a viable solution for biomass gasification downstream gas clean-up. This program was conducted from October 1 2008 to February 28 2011 and divided into five major tasks. - Task A: Perform conceptual design and conduct preliminary system and economic analysis (Q1 2009 ~ Q2 2009) - Task B: Biomass gasification tests, product characterization, and CPO tar conversion catalyst preparation. This task will be conducted after completing process design and system economics analysis

  7. Wet steam treatment with oxygen

    Energy Technology Data Exchange (ETDEWEB)

    Ruehle, W.; Enkler, G. [EnBW Kraftwerke AG, Kernkraftwerk Philippsburg (Germany)

    1999-07-01

    After many years of excellent results using high all volatile treatment (HAVT) for operation of the secondary system of a PWR, flow assisted corrosion in the heating pipes of the intermediate steam reheaters has been experienced. Oxygen addition into the heating steam before the reheater is expected to improve the protective oxide layers formation. The reaction of oxygen with the alkalizing steam ingredients is described. (orig.)

  8. Investigation of dynamic load changes of a combined cycle power plant with circulating pressurized fluidized bed using a simulation model; Untersuchungen zum dynamischen Lastaenderungsverhalten eines Kombi-Kraftwerks mit zirkulierender Druckwirbelschicht mit Hilfe eines Simulationsmodells

    Energy Technology Data Exchange (ETDEWEB)

    Bockamp, S.; Krumm, W.

    2001-07-01

    Fluidized bed combustion technology offers high efficient power plants with low emissions using coal, biomass or waste as fuel input. Mathematical models support the optimisation and design of power plants. The mathematical fluidized bed system model developed at the Institut fuer Energietechnik, Universitaet Siegen, allows the simulation of steady state or dynamic process operation behaviour. This model is used for detailed examining of the overall combined cycle power plant and the interactions between the single components gas turbine, furnace and water-/steam cycle. The described simulation model presented in this paper is applied for the determination of the transient operation behaviour of a combined cycle power plant based on pressurized circulating fluidized bed combustion. The effects of a step function load change on the temperature profile, the emissions and on process reaction of water/steam cycle and on gas turbine is analysed and discussed in detail at different component outlets. (orig.) [German] Das Kombi-Kraftwerk mit zirkulierender Druckwirbelschichtfeuerung stellt ein effizientes und emissionsarmes Konzept dar. Neben den wirbelschichtinhaerenten Eigenschaften wie geringerer Schadstoffbildung durch niedrige Feuerraumtemperaturen und der integrierten Schadstoffreduktion durch die Zugabe von Zuschlagstoffen verspricht die druckaufgeladenen Variante aufgrund der hohen Querschnittsbelastung eine kompakte Bauart sowie einen fuer die Verstromung von Kohlen hohen Wirkungsgrad. Kohle kann mit diesem Verfahren direkt innerhalb eines Gasturbinenprozesses genutzt werden. Mit Hilfe der mathematischen Modellbildung koennen die dynamischen Auswirkungen auf das Gesamtsystem Kombi-Kraftwerk untersucht werden. (orig.)

  9. Bio-Fuel Production Assisted with High Temperature Steam Electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Grant Hawkes; James O' Brien; Michael McKellar

    2012-06-01

    Two hybrid energy processes that enable production of synthetic liquid fuels that are compatible with the existing conventional liquid transportation fuels infrastructure are presented. Using biomass as a renewable carbon source, and supplemental hydrogen from high-temperature steam electrolysis (HTSE), these two hybrid energy processes have the potential to provide a significant alternative petroleum source that could reduce dependence on imported oil. The first process discusses a hydropyrolysis unit with hydrogen addition from HTSE. Non-food biomass is pyrolyzed and converted to pyrolysis oil. The pyrolysis oil is upgraded with hydrogen addition from HTSE. This addition of hydrogen deoxygenates the pyrolysis oil and increases the pH to a tolerable level for transportation. The final product is synthetic crude that could then be transported to a refinery and input into the already used transportation fuel infrastructure. The second process discusses a process named Bio-Syntrolysis. The Bio-Syntrolysis process combines hydrogen from HTSE with CO from an oxygen-blown biomass gasifier that yields syngas to be used as a feedstock for synthesis of liquid synthetic crude. Conversion of syngas to liquid synthetic crude, using a biomass-based carbon source, expands the application of renewable energy beyond the grid to include transportation fuels. It can also contribute to grid stability associated with non-dispatchable power generation. The use of supplemental hydrogen from HTSE enables greater than 90% utilization of the biomass carbon content which is about 2.5 times higher than carbon utilization associated with traditional cellulosic ethanol production. If the electrical power source needed for HTSE is based on nuclear or renewable energy, the process is carbon neutral. INL has demonstrated improved biomass processing prior to gasification. Recyclable biomass in the form of crop residue or energy crops would serve as the feedstock for this process. A process model

  10. Bio-Fuel Production Assisted with High Temperature Steam Electrolysis

    Energy Technology Data Exchange (ETDEWEB)

    Grant Hawkes; James O' Brien; Michael McKellar

    2012-06-01

    Two hybrid energy processes that enable production of synthetic liquid fuels that are compatible with the existing conventional liquid transportation fuels infrastructure are presented. Using biomass as a renewable carbon source, and supplemental hydrogen from high-temperature steam electrolysis (HTSE), these two hybrid energy processes have the potential to provide a significant alternative petroleum source that could reduce dependence on imported oil. The first process discusses a hydropyrolysis unit with hydrogen addition from HTSE. Non-food biomass is pyrolyzed and converted to pyrolysis oil. The pyrolysis oil is upgraded with hydrogen addition from HTSE. This addition of hydrogen deoxygenates the pyrolysis oil and increases the pH to a tolerable level for transportation. The final product is synthetic crude that could then be transported to a refinery and input into the already used transportation fuel infrastructure. The second process discusses a process named Bio-Syntrolysis. The Bio-Syntrolysis process combines hydrogen from HTSE with CO from an oxygen-blown biomass gasifier that yields syngas to be used as a feedstock for synthesis of liquid synthetic crude. Conversion of syngas to liquid synthetic crude, using a biomass-based carbon source, expands the application of renewable energy beyond the grid to include transportation fuels. It can also contribute to grid stability associated with non-dispatchable power generation. The use of supplemental hydrogen from HTSE enables greater than 90% utilization of the biomass carbon content which is about 2.5 times higher than carbon utilization associated with traditional cellulosic ethanol production. If the electrical power source needed for HTSE is based on nuclear or renewable energy, the process is carbon neutral. INL has demonstrated improved biomass processing prior to gasification. Recyclable biomass in the form of crop residue or energy crops would serve as the feedstock for this process. A process model

  11. Hydrogen-based power generation from bioethanol steam reforming

    Science.gov (United States)

    Tasnadi-Asztalos, Zs.; Cormos, C. C.; Agachi, P. S.

    2015-12-01

    This paper is evaluating two power generation concepts based on hydrogen produced from bioethanol steam reforming at industrial scale without and with carbon capture. The power generation from bioethanol conversion is based on two important steps: hydrogen production from bioethanol catalytic steam reforming and electricity generation using a hydrogen-fuelled gas turbine. As carbon capture method to be assessed in hydrogen-based power generation from bioethanol steam reforming, the gas-liquid absorption using methyl-di-ethanol-amine (MDEA) was used. Bioethanol is a renewable energy carrier mainly produced from biomass fermentation. Steam reforming of bioethanol (SRE) provides a promising method for hydrogen and power production from renewable resources. SRE is performed at high temperatures (e.g. 800-900°C) to reduce the reforming by-products (e.g. ethane, ethene). The power generation from hydrogen was done with M701G2 gas turbine (334 MW net power output). Hydrogen was obtained through catalytic steam reforming of bioethanol without and with carbon capture. For the evaluated plant concepts the following key performance indicators were assessed: fuel consumption, gross and net power outputs, net electrical efficiency, ancillary consumptions, carbon capture rate, specific CO2 emission etc. As the results show, the power generation based on bioethanol conversion has high energy efficiency and low carbon footprint.

  12. Hydrogen-based power generation from bioethanol steam reforming

    Energy Technology Data Exchange (ETDEWEB)

    Tasnadi-Asztalos, Zs., E-mail: tazsolt@chem.ubbcluj.ro; Cormos, C. C., E-mail: cormos@chem.ubbcluj.ro; Agachi, P. S. [Babes-Bolyai University, Faculty of Chemistry and Chemical Engineering, 11 Arany Janos, Postal code: 400028, Cluj-Napoca (Romania)

    2015-12-23

    This paper is evaluating two power generation concepts based on hydrogen produced from bioethanol steam reforming at industrial scale without and with carbon capture. The power generation from bioethanol conversion is based on two important steps: hydrogen production from bioethanol catalytic steam reforming and electricity generation using a hydrogen-fuelled gas turbine. As carbon capture method to be assessed in hydrogen-based power generation from bioethanol steam reforming, the gas-liquid absorption using methyl-di-ethanol-amine (MDEA) was used. Bioethanol is a renewable energy carrier mainly produced from biomass fermentation. Steam reforming of bioethanol (SRE) provides a promising method for hydrogen and power production from renewable resources. SRE is performed at high temperatures (e.g. 800-900°C) to reduce the reforming by-products (e.g. ethane, ethene). The power generation from hydrogen was done with M701G2 gas turbine (334 MW net power output). Hydrogen was obtained through catalytic steam reforming of bioethanol without and with carbon capture. For the evaluated plant concepts the following key performance indicators were assessed: fuel consumption, gross and net power outputs, net electrical efficiency, ancillary consumptions, carbon capture rate, specific CO{sub 2} emission etc. As the results show, the power generation based on bioethanol conversion has high energy efficiency and low carbon footprint.

  13. The chemistry involved in the steam treatment of lignocellulosic materials

    Directory of Open Access Journals (Sweden)

    Luiz Pereira Ramos

    2003-12-01

    Full Text Available Pretreatment of lignocellulosic materials is essential for bioconversion because of the various physical and chemical barriers that greatly inhibit their susceptibility to bioprocesses such as hydrolysis and fermentation. The aim of this article is to review some of the most important pretreatment methods developed to date to enhance the conversion of lignocellulosics. Steam explosion, which precludes the treatment of biomass with high-pressure steam under optimal conditions, is presented as the pretreatment method of choice and its mode of action on lignocellulosics is discussed. The optimal pretreatment conditions for a given plant biomass are defined as those in which the best substrate for hydrolysis is obtained with the least amount of soluble sugars lost to side reactions such as dehydration. Therefore, pretreatment optimization results from a compromise between two opposite trends because hemicellulose recovery in acid hydrolysates can only be maximized at lower pretreatment severities, whereas the development of substrate accessibility requires more drastic pretreatment conditions in which sugar losses are inevitable. To account for this heterogeneity, the importance of several process-oriented parameters is discussed in detail, such as the pretreatment temperature, residence time into the steam reactor, use of an acid catalyst, susceptibility of the pretreated biomass to bioconversion, and process design.

  14. Regenerative superheated steam turbine cycles

    Science.gov (United States)

    Fuller, L. C.; Stovall, T. K.

    1980-01-01

    PRESTO computer program was developed to analyze performance of wide range of steam turbine cycles with special attention given to regenerative superheated steam turbine cycles. It can be used to model standard turbine cycles, including such features as process steam extraction, induction and feedwater heating by external sources, peaking, and high back pressure. Expansion line efficiencies, exhaust loss, leakages, mechanical losses, and generator losses are used to calculate cycle heat rate and generator output. Program provides power engineer with flexible aid for design and analysis of steam turbine systems.

  15. 流化床内生物质石英砂双组分混合流动混沌递归分析%Chaotic recurrence analysis of two-component flow of mixed biomass particles and quartz sands in fluidized-bed

    Institute of Scientific and Technical Information of China (English)

    王肖祎; 仲兆平; 王春华

    2014-01-01

    Recurrence plot and recurrence quantification analysis were used to analyze the pressure fluctuation signal, and particle flow characteristics at different numbers of biomass, quartz sands and different gas velocities were investigated. The quartz sands with the diameter of 0.8 mm and cylinder-shaped biomass particles with both diameter and length of 10 mm were used as bed materials. In the bubbling section, the periodicity of the system decreased first and then increased with increasing proportion of biomass. In the slugging section, recurrence plots of signal had the same textural feature in the fluidized-bed before and after biomass was added. The bubbling section determinism and laminarity flow rate increased with increasing gas velocity, and significantly decreased at a low proportion of biomass, but entropy of the system decreased with increasing gas velocity. The slugging section determinism and laminarity flow rate had a small change and entropy of the system decreased with increasing gas velocity, showing opposite tendency from the one-component system.%采用递归分析方法对流化床内的压力脉动信号进行分析,研究了不同工况下石英砂与柱形生物质颗粒混合双组分颗粒的流动特性。柱形生物质颗粒尺寸为10 mm×10 mm(直径×长),石英砂粒径为0.8 mm。在鼓泡床阶段,随着生物质含量的增加,系统的周期性呈现先减弱再增强的变化趋势;该阶段确定性与层流率均表现为随气速的增加而增大,其值在生物质含量低时会明显减小,系统熵则随着气速的增大而减小。在腾涌阶段,生物质添加前后系统信号的递归图呈现相似的纹理特征,确定性与层流率变化较小,此时熵随着气速的增加而减小,与单组分流动呈现相反的趋势。

  16. Atmospheric fluidized bed combustion advanced concept system

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    DONLEE Technologies Inc. is developing with support of the US Department of Energy an advanced circulating fluidized bed technology known as the Vortex{trademark} Fluidized Bed Combustor (VFBC). The unique feature of the VFBC is the injection of a significant portion of the combustion air into the cyclone. Since as much as one-half of the total combustion air is injected into the cyclone, the cross-sectional area of the circulating fluidized bed is considerably smaller than typical circulating fluidized beds. The technology is being developed for two applications: Industrial-scale boilers ranging from 20,000 to 100,000 pounds per hour steam generating capacity; and two-stage combustion in which a substoichiometric Vortex Fluidized Bed Combustor (2VFBC) or precombustor is used to generate a combustible gas for use primarily in boiler retrofit applications. This Level II analysis of these two applications indicates that both have merit. An industrial-scale VFBC boiler (60,000 lb/hr of steam) is projected to be economically attractive with coal prices as high as $40 per ton and gas prices between $4 and $5 per thousand cubic feet. The payback time is between 3 and 4 years. The 2VFBC system was evaluated at three capacities of application: 20,000; 60,000 and 100,000 lb/hr of steam. The payback times for these three capacities are 4.5, 2.1 and 1.55 years, respectively. The 2VFBC has potential applications for retrofit of existing pulverized coal-fired boilers or as a new large (utility) boiler. Pressurized operation of the 2VFBC has considerable potential for combined cycle power generation applications. Experimental development of both applications is presented here to demonstrate the potential of these two technologies.

  17. NONUNIFORMITIES OF TWO-PHASE COOLANT DISTRIBUTION IN A HEAT GENERATING PARTICLES BED

    Directory of Open Access Journals (Sweden)

    V. V. Sorokin

    2014-01-01

    Full Text Available Sufficient atomic power generation safety increase may be done with microfuel adapting to reactor plants with water coolant. Microfuel particle is a millimeter size grain containing fission material core in a protecting coverage. The coverage protects fuel contact with coolant and provides isolation of fission products inside. Well thermophysical properties of microfuel bed in a direct contact with water coolant excludes fuel overheating when accidents. Microfuel use was suggested for a VVER, а direct flow reactor for superheat steam generation, a reactor with neutron spectra adjustment by the steam partial content varying in the coolant.Nonuniformities of two-phase coolant distribution in a heat generating particles bed are predicted by calculations in this text. The one is due to multiple-valuedness of pressure drop across the bed on the steam quality dependency. The nonuniformity decreases with flow rate and particle size growths absolute pressure diminishing while porosity effect is weak. The worse case is for pressure quality of order of one. Some pure steam filled pores appears parallel to steam water mixture filled pores, latter steam quality is less than the mean of the bed. Considering this regime for the direct flow reactor for superheat steam generation we predict some water drops at the exit flow. The two-phase coolant filtration with subcooled water feed is unstable to strong disturbance effects are found. Uniformity of two-phase coolant distribution is worse than for one-phase in the same radial type reactor.

  18. Steam refining as an alternative to steam explosion.

    Science.gov (United States)

    Schütt, Fokko; Westereng, Bjørge; Horn, Svein J; Puls, Jürgen; Saake, Bodo

    2012-05-01

    In steam pretreatment the defibration is usually achieved by an explosion at the end of the treatment, but can also be carried out in a subsequent refiner step. A steam explosion and a steam refining unit were compared by using the same raw material and pretreatment conditions, i.e. temperature and time. Smaller particle size was needed for the steam explosion unit to obtain homogenous slurries without considerable amounts of solid chips. A higher amount of volatiles could be condensed from the vapour phase after steam refining. The results from enzymatic hydrolysis showed no significant differences. It could be shown that, beside the chemical changes in the cell wall, the decrease of the particle size is the decisive factor to enhance the enzymatic accessibility while the explosion effect is not required.

  19. Simulation of Biomass Accumulation Pattern in Vapor-Phase Biofilters.

    Science.gov (United States)

    Xi, Jin-Ying; Hu, Hong-Ying; Zhang, Xian

    2012-06-01

    Existence of inert biomass and its impact on biomass accumulation patterns and biofilter performance were investigated. Four biofilters were set up in parallel to treat gaseous toluene. Each biofilter operated under different inlet toluene loadings for 100 days. Two microbial growth models, one with an inert biomass assumption and the other without, were established and compared. Results from the model with the inert biomass assumption showed better agreement with the experimental data than those based on the model without the inert biomass assumption thus verifying that inert biomass accumulation cannot be ignored in the long-term operation of biofilters. According to the model with an inert biomass assumption, the ratio of active biomass to total biomass will decrease and the inert biomass will become dominant in total biomass after a period of time. Filter bed structure simulation results showed that the void fraction is more sensitive to biomass accumulation than the specific surface area. The final void fraction of the biofilters with the highest inlet toluene loading is only 67% of its initial level while the final specific surface area is 82%. Identification and quantification of inert biomass will give a better understanding of biomass accumulation in biofilters and will result in a more exact simulation of biomass change during long-term operations. Results also indicate that an ideal biomass control technique should be able to remove most inert biomass while simultaneously preserving as much active biomass as possible.

  20. Simulation of Biomass Accumulation Pattern in Vapor-Phase Biofilters

    Science.gov (United States)

    Xi, Jin-Ying; Hu, Hong-Ying; Zhang, Xian

    2012-01-01

    Abstract Existence of inert biomass and its impact on biomass accumulation patterns and biofilter performance were investigated. Four biofilters were set up in parallel to treat gaseous toluene. Each biofilter operated under different inlet toluene loadings for 100 days. Two microbial growth models, one with an inert biomass assumption and the other without, were established and compared. Results from the model with the inert biomass assumption showed better agreement with the experimental data than those based on the model without the inert biomass assumption thus verifying that inert biomass accumulation cannot be ignored in the long-term operation of biofilters. According to the model with an inert biomass assumption, the ratio of active biomass to total biomass will decrease and the inert biomass will become dominant in total biomass after a period of time. Filter bed structure simulation results showed that the void fraction is more sensitive to biomass accumulation than the specific surface area. The final void fraction of the biofilters with the highest inlet toluene loading is only 67% of its initial level while the final specific surface area is 82%. Identification and quantification of inert biomass will give a better understanding of biomass accumulation in biofilters and will result in a more exact simulation of biomass change during long-term operations. Results also indicate that an ideal biomass control technique should be able to remove most inert biomass while simultaneously preserving as much active biomass as possible. PMID:22693411

  1. Grimethorpe experimental pressurized fluidized-bed combustor: in future energy concepts

    Energy Technology Data Exchange (ETDEWEB)

    Broadbent, D.B.

    1979-01-01

    The experimental pressurized fluidized bed combustor project at Grimethorpe, UK, is described. The design of the combustor, which is a pressure vessel containing a furnace, which contains the fluidized bed is discussed. Details of the process, the steam water circuit, the fuel system and method of feeding coal, ash removal during the process, the water treatment plant and plant control are given.

  2. Combustion, pyrolysis, gasification, and liquefaction of biomass

    Energy Technology Data Exchange (ETDEWEB)

    Reed, T.B.

    1980-09-01

    All the products now obtained from oil can be provided by thermal conversion of the solid fuels biomass and coal. As a feedstock, biomass has many advantages over coal and has the potential to supply up to 20% of US energy by the year 2000 and significant amounts of energy for other countries. However, it is imperative that in producing biomass for energy we practice careful land use. Combustion is the simplest method of producing heat from biomass, using either the traditional fixed-bed combustion on a grate or the fluidized-bed and suspended combustion techniques now being developed. Pyrolysis of biomass is a particularly attractive process if all three products - gas, wood tars, and charcoal - can be used. Gasification of biomass with air is perhaps the most flexible and best-developed process for conversion of biomass to fuel today, yielding a low energy gas that can be burned in existing gas/oil boilers or in engines. Oxygen gasification yields a gas with higher energy content that can be used in pipelines or to fire turbines. In addition, this gas can be used for producing methanol, ammonia, or gasoline by indirect liquefaction. Fast pyrolysis of biomass produces a gas rich in ethylene that can be used to make alcohols or gasoline. Finally, treatment of biomass with high pressure hydrogen can yield liquid fuels through direct liquefaction.

  3. Steam generator tube integrity program

    Energy Technology Data Exchange (ETDEWEB)

    Dierks, D.R.; Shack, W.J. [Argonne National Laboratory, IL (United States); Muscara, J.

    1996-03-01

    A new research program on steam generator tubing degradation is being sponsored by the U.S. Nuclear Regulatory Commission (NRC) at Argonne National Laboratory. This program is intended to support a performance-based steam generator tube integrity rule. Critical areas addressed by the program include evaluation of the processes used for the in-service inspection of steam generator tubes and recommendations for improving the reliability and accuracy of inspections; validation and improvement of correlations for evaluating integrity and leakage of degraded steam generator tubes, and validation and improvement of correlations and models for predicting degradation in steam generator tubes as aging occurs. The studies will focus on mill-annealed Alloy 600 tubing, however, tests will also be performed on replacement materials such as thermally-treated Alloy 600 or 690. An overview of the technical work planned for the program is given.

  4. Hydrogen production from high moisture content biomass in supercritical water

    Energy Technology Data Exchange (ETDEWEB)

    Antal, M.J. Jr.; Xu, X. [Univ. of Hawaii, Honolulu, HI (United States). Hawaii Natural Energy Inst.

    1998-08-01

    By mixing wood sawdust with a corn starch gel, a viscous paste can be produced that is easily delivered to a supercritical flow reactor by means of a cement pump. Mixtures of about 10 wt% wood sawdust with 3.65 wt% starch are employed in this work, which the authors estimate to cost about $0.043 per lb. Significant reductions in feed cost can be achieved by increasing the wood sawdust loading, but such an increase may require a more complex pump. When this feed is rapidly heated in a tubular flow reactor at pressures above the critical pressure of water (22 MPa), the sawdust paste vaporizes without the formation of char. A packed bed of carbon catalyst in the reactor operating at about 650 C causes the tarry vapors to react with water, producing hydrogen, carbon dioxide, and some methane with a trace of carbon monoxide. The temperature and history of the reactor`s wall influence the hydrogen-methane product equilibrium by catalyzing the methane steam reforming reaction. The water effluent from the reactor is clean. Other biomass feedstocks, such as the waste product of biodiesel production, behave similarly. Unfortunately, sewage sludge does not evidence favorable gasification characteristics and is not a promising feedstock for supercritical water gasification.

  5. Biomass [updated

    Energy Technology Data Exchange (ETDEWEB)

    Turhollow Jr, Anthony F [ORNL

    2016-01-01

    Biomass resources and conversion technologies are diverse. Substantial biomass resources exist including woody crops, herbaceous perennials and annuals, forest resources, agricultural residues, and algae. Conversion processes available include fermentation, gasification, pyrolysis, anaerobic digestion, combustion, and transesterification. Bioderived products include liquid fuels (e.g. ethanol, biodiesel, and gasoline and diesel substitutes), gases, electricity, biochemical, and wood pellets. At present the major sources of biomass-derived liquid fuels are from first generation biofuels; ethanol from maize and sugar cane (89 billion L in 2013) and biodiesel from vegetable oils and fats (24 billion liters in 2011). For other than traditional uses, policy in the forms of mandates, targets, subsidies, and greenhouse gas emission targets has largely been driving biomass utilization. Second generation biofuels have been slow to take off.

  6. Experimental investigation on the changes in bed properties of a ...

    African Journals Online (AJOL)

    Experimental investigation on the changes in bed properties of a downdraft biomass gasifier. ... pressure measurements, physical observation, sampling of bed particles, ... char properties viz., weight, volume, density and volatile matter content along ... Specific gasification rate for wood pieces was found to be 75 kg h-1 m-2 ...

  7. YEAR 2 BIOMASS UTILIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Zygarlicke

    2004-11-01

    This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

  8. YEAR 2 BIOMASS UTILIZATION

    Energy Technology Data Exchange (ETDEWEB)

    Christopher J. Zygarlicke

    2004-11-01

    This Energy & Environmental Research Center (EERC) Year 2 Biomass Utilization Final Technical Report summarizes multiple projects in biopower or bioenergy, transportation biofuels, and bioproducts. A prototype of a novel advanced power system, termed the high-temperature air furnace (HITAF), was tested for performance while converting biomass and coal blends to energy. Three biomass fuels--wood residue or hog fuel, corn stover, and switchgrass--and Wyoming subbituminous coal were acquired for combustion tests in the 3-million-Btu/hr system. Blend levels were 20% biomass--80% coal on a heat basis. Hog fuel was prepared for the upcoming combustion test by air-drying and processing through a hammer mill and screen. A K-Tron biomass feeder capable of operating in both gravimetric and volumetric modes was selected as the HITAF feed system. Two oxide dispersion-strengthened (ODS) alloys that would be used in the HITAF high-temperature heat exchanger were tested for slag corrosion rates. An alumina layer formed on one particular alloy, which was more corrosion-resistant than a chromia layer that formed on the other alloy. Research activities were completed in the development of an atmospheric pressure, fluidized-bed pyrolysis-type system called the controlled spontaneous reactor (CSR), which is used to process and condition biomass. Tree trimmings were physically and chemically altered by the CSR process, resulting in a fuel that was very suitable for feeding into a coal combustion or gasification system with little or no feed system modifications required. Experimental procedures were successful for producing hydrogen from biomass using the bacteria Thermotoga, a deep-ocean thermal vent organism. Analytical procedures for hydrogen were evaluated, a gas chromatography (GC) method was derived for measuring hydrogen yields, and adaptation culturing and protocols for mutagenesis were initiated to better develop strains that can use biomass cellulose. Fly ash derived from

  9. Solar tower power plant using a particle-heated steam generator: Modeling and parametric study

    Science.gov (United States)

    Krüger, Michael; Bartsch, Philipp; Pointner, Harald; Zunft, Stefan

    2016-05-01

    Within the framework of the project HiTExStor II, a system model for the entire power plant consisting of volumetric air receiver, air-sand heat exchanger, sand storage system, steam generator and water-steam cycle was implemented in software "Ebsilon Professional". As a steam generator, the two technologies fluidized bed cooler and moving bed heat exchangers were considered. Physical models for the non-conventional power plant components as air- sand heat exchanger, fluidized bed coolers and moving bed heat exchanger had to be created and implemented in the simulation environment. Using the simulation model for the power plant, the individual components and subassemblies have been designed and the operating parameters were optimized in extensive parametric studies in terms of the essential degrees of freedom. The annual net electricity output for different systems was determined in annual performance calculations at a selected location (Huelva, Spain) using the optimized values for the studied parameters. The solution with moderate regenerative feed water heating has been found the most advantageous. Furthermore, the system with moving bed heat exchanger prevails over the system with fluidized bed cooler due to a 6 % higher net electricity yield.

  10. Kinetics of gasification and combustion of residues, biomass and coal in a bubbling fluidized bed; Die Kinetik der Vergasung und Verbrennung unterschiedlicher Abfaelle, Biomassen und Kohlen in der blasenbildenden Wirbelschicht

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, S.; Krumm, W. [Siegen Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Energie- und Umweltverfahrenstechnik

    1998-09-01

    The combustion and gasification characteristics of Rhenish brown coal, domestic waste, waste plastics, wood and sewage sludge were investigated in a bubbling atmospheric fluidized bed in the laboratory scale. The materials were pyrolyzed in the fluidized bed in a nitrogen atmosphere. The residual coke was combuted in the presence of oxygen with varying operating parameters or else gasified in the presence of carbon dioxide. The different materials were characterized by global combustion rates, and kinetic parameters were determined for residual coke combustion. (orig.) [Deutsch] Das Verbrennungs- und Vergasungsverhalten von Rheinischer Braunkohle, Hausmuell, Restkunststoff, Holz und Klaerschlamm wurde in einer blasenbildenden, atmosphaerischen Laborwirbelschicht untersucht. Die Einsatzstoffe wurden in der mit Stickstoff fluidisierten Wirbelschicht pyrolysiert. Der verbleibende Restkoks wurde anschliessend unter Variation der Betriebsparameter mit Sauerstoff verbrannt oder mit Kohlendioxid vergast. Die unterschiedlichen Einsatzstoffe wurden durch globale Vebrennungsraten charakterisiert. Fuer die Restkoksverbrennung wurden kinetische Parameter ermittelt. (orig.)

  11. Contributions ECN biomass to 'Developments in thermochemical biomass conversion' conference. 17-22 September 2000, Tyrol, Austria

    Energy Technology Data Exchange (ETDEWEB)

    Boerrigter, H.; Daey Ouwens, C.; Van Doorn, J.; Van der Drift, A.; Hofmans, H.; Huijnen, H.; Kersten, S.R.A.; Kiel, J.H.A.; Moonen, R.H.W.; Mozaffarian, M.; Neeft, J.P.A.; Oosting, T.P.; Den Uil, H.; Visser, H.J.M.; Zwart, R.W.R. [ECN , Biomass, Petten (Netherlands)

    2000-07-01

    This report contains the contributions (7) of the business unit ECN Biomass of the Netherlands Energy Research Foundation (ECN) in Petten, Netherlands, to the title conference. Separate abstracts were prepared for each of the seven papers: (1) Effect of fuel size and process temperature on fuel gas quality from CFB gasification of biomass; (2) Gas mixing in a pilot scale (500 KW{sub th}) air blown circulating fluidised bed biomass gasifier; (3) Guideline for sampling and analysis of 'tars' and particles in biomass producer gases; (4) Biomass ash - bed material interactions leading to agglomeration in fluidised bed combustion and gasification; (5) Production of substitute natural gas by biomass hydrogasification; (6) CASST. A new and advanced process for biomass gasification; and (7) New developments in the field of tri-generation from biomass and waste. A survey.

  12. Effect of Steam Explosion Pretreatment on the Specific Methane Yield of Miscanthus x giganteus

    OpenAIRE

    Franz Theuretzbacher; Javier Lizasoain; Simona Menardo; Paal Jahre Nilsen; Andreas Gronauer; Alexander Bauer

    2014-01-01

    A highly promising energy crop for biogas production can be Miscanthus x giganteus. It has multiple advantages, which include low soil requirements and the existence of genotypes adapted to dry conditions in comparison to other energy crops. Miscanthus cannot be used in the biogas plant without a pretreatment due to the recalcitrant nature of lignocelluloses. One of the most efficient pretreatment methods for lignocellulosic biomass is steam explosion. This includes heating the biomass...

  13. In-vessel coolability and steam explosion in Nordic BWRs

    Energy Technology Data Exchange (ETDEWEB)

    Ma, W.; Hansson, R.; Li, L.; Kudinov, P.; Cadinu, F.; Tran, C-.T. (Royal Institute of Technology (KTH), Stockholm (Sweden))

    2010-05-15

    The INCOSE project is to reduce the uncertainty in quantification of steam explosion risk and in-vessel coolability in Nordic BWR plants with the cavity flooding as a severe accident management (SAM) measure. During 2009 substantial advances and new insights into physical mechanisms were gained for studies of: (i) in-vessel corium coolability - development of the methodologies to assess the efficiency of the control rod guide tube (CRGT) cooling as a potential SAM measure; (ii) debris bed coolability - characterization of the effective particle diameter of multi-size particles and qualification of friction law for two-phase flow in the beds packed with multi-size particles; and (iii) steam explosion - investigation of the effect of binary oxides mixture's properties on steam explosion. An approach for coupling of ECM/PECM models with RELAP5 was developed to enhance predictive fidelity for melt pool heat transfer. MELCOR was employed to examine the CRGT cooling efficiency by considering an entire accident scenario, and the simulation results show that the nominal flowrate (approx10kg/s) of CRGT cooling is sufficient to maintain the integrity of the vessel in a BWR of 3900 MWth, if the water injection is activated no later than 1 hour after scram. The POMECO-FL experimental data suggest that for a particulate bed packed with multi-size particles, the effective particle diameter can be represented by the area mean diameter of the particles, while at high velocity (Re>7) the effective particle diameter is closer to the length mean diameter. The pressure drop of two-phase flow through the particulate bed can be predicted by Reed's model. The steam explosion experiments performed at high melt superheat (>200oC) using oxidic mixture of WO3-CaO didn't detect an apparent difference in steam explosion energetics and preconditioning between the eutectic and noneutectic melts. This points out that the next step of MISTEE experiment will be conducted at lower

  14. Economic evaluation of externally fired gas turbine cycles for small-scale biomass cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    Anheden, Marie [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Chemical Engineering and Technology

    2001-01-01

    In this conceptual study, externally fired gas turbine (EFGT) cycles in combination with a biomass-fueled, atmospheric circulating fluidized bed (CFB) furnace are investigated for small scale heat and power production ({approx} 8 MW fuel input). Three cycle configurations are considered: closed cycle, with nitrogen, helium, and a helium/carbon dioxide mixture as working fluids; open cycle operating in parallel to the CFB system; and open cycle with a series connection to the CFB system. Intercooling, postcooling, and recuperation are employed with the goal of maximizing efficiency. Aside from a thermodynamic performance analysis, the study includes an economic analysis of both the closed and open externally fired gas turbine configurations, and comparisons are made with existing and emerging alternatives for small-scale biomass cogeneration. Simulation results show that thermodynamic performance varies slightly between the different configurations and working fluids, with electrical efficiencies of 31-38% (LHV) and total efficiency of 85-106% (LHV). The economic evaluation shows that the turbomachinery and the CFB furnace dominate the total plant cost, with each contributing about 1/3 of the total installed equipment cost. The specific capital cost for installation in Sweden in 1998 currency is calculated as 26-31 kSEK/kW{sub e} which is equivalent to 3 200-3 900 USD/kW{sub e} or 2 700-3 300 EUR/kW{sub e} .The cost of electricity, COE, is estimated to 590-670 SEK/MWh{sub e} (equivalent to 73-84 USD/MWh{sub e} or 62-71 EUR/MWh{sub e}) for 4 000 full load hours per year in a cogeneration application. Comparing the economic results for the externally fired gas turbine cycles in a slightly larger scale (40-50 MW{sub f}) to the economics of conventional biomass fired steam turbine cycles shows that the cost of electricity for the two plant configurations are roughly the same with a COE of 300-350 SEK/MWh{sub e}. It is believed that the economic performance of the EFGT

  15. Topping PCFB combustion plant with supercritical steam pressure

    Energy Technology Data Exchange (ETDEWEB)

    Robertson, A. [Foster Wheeler Development Corp., Livingston, NJ (United States); White, J. [Parsons Power Group Inc., Reading, PA (United States)

    1997-11-01

    Research is being conducted to develop a new type of coal fired plant for electric power generation. This new type of plant, called a second generation or topping pressurized circulating fluidized bed combustion (topping PCFB) plant, offers the promise of efficiencies greater than 46 percent (HHV), with both emissions and a cost of electricity that are significantly lower than conventional pulverized coal fired plants with scrubbers. The topping PCFB plant incorporates the partial gasification of coal in a carbonizer, the combustion of carbonizer char in a pressurized circulating fluidized bed combustor (PCFB), and the combustion of carbonizer fuel gas in a topping combustor to achieve gas turbine inlet temperatures of 2,300 F and higher. After completing pilot plant tests of a carbonizer, a PCFB, and a gas turbine topping combustor, all being developed for this new plant, the authors calculated a higher heating value efficiency of 46.2 percent for the plant. In that analysis, the plant operated with a conventional 2,400 psig steam cycle with 1,000 F superheat and reheat steam and a 2.5 inch mercury condenser back pressure. This paper identifies the efficiency gains that this plant will achieve by using supercritical pressure steam conditions.