WorldWideScience

Sample records for bearing thermocleavable benzoate

  1. Photovoltaic Performance of Polymers Based on Dithienylthienopyrazines Bearing Thermocleavable Benzoate Esters

    DEFF Research Database (Denmark)

    Petersen, Martin Helgesen; Krebs, Frederik C

    2010-01-01

    , and a second weight loss above 400 °C, corresponding to loss of CO2 and decomposition. Upon thermocleavage the power conversion efficiency decreased for all the polymers while the polymer films became insoluble which was desired in the context of multilayer film processing. Thermocleavable low......Thermocleavable low-band-gap polymers based on dithienylthienopyrazines were prepared and copolymerized with different donor units like dialkoxybenzene, fluorene, thiophene, and cyclopentadithiophene (CPDT) using both Stille and Suzuki cross-coupling reactions. In the solid state the band gaps...... are in the range of 1.17−1.37 eV. The polymers were explored as donor materials in bulk heterojunction solar cells together with PCBM as the acceptor material where they were shown to exhibit a photoresponse in the full absorption range up to 900 nm and power conversion efficiencies of up to 1.21% under 1 sun...

  2. Method of Thermocleaving a Polymer Layer

    DEFF Research Database (Denmark)

    2010-01-01

    A method of thermocleaving a thermocleavable polymer layer which is in thermal contact with a heat sensitive component that is not tolerant of the temperature required for thermocleavage of the thermocleavable polymer layer, in which the thermocleavable polymer layer is illuminated with a light...... source having a wavelength range more strongly absorbed by the thermocleavable polymer and substantially less strongly absorbed by the heat sensitive component, such that the thermocleavable polymer layer reaches a temperature sufficient to cause thermocleavage of the polymer without causing detrimental...

  3. Thermo-cleavable polymers: Materials with enhanced photochemical stability

    DEFF Research Database (Denmark)

    Manceau, Matthieu; Petersen, Martin Helgesen; Krebs, Frederik C

    2010-01-01

    Photochemical stability of three thermo-cleavable polymers was investigated as thin films under atmospheric conditions. A significant increase in lifetime was observed once the side-chain was cleaved emphasizing the detrimental effect of solubilizing groups on the photochemical stability of...... conjugated polymers. In addition to their ease of processing, thermo-cleavable polymers thus also offer a greater intrinsic stability under illumination....

  4. Thermocleavable pi-Conjugated polymers. Synthesis and photovoltaic applications

    Energy Technology Data Exchange (ETDEWEB)

    Helgesen, M.

    2009-10-15

    Polymer solar cells (plastic solar cells) have seen remarkable improvements in recent years where power conversion efficiencies of up to 6% have been reported for small area devices. However in terms of stability polymer solar cells degrade during illumination and in the dark leading to operational lifetimes that are generally very poor. There has been a recent interest in the operational stability of devices and more importantly on the understanding of why devices and materials break down. This has lead to the discovery of a new class of materials that enable exceptionally long device lifetimes (>20000 hours). This Ph.D. thesis describes the synthesis, characterization and photovoltaic applications of these novel polymer materials. A key feature of these materials is that solubilizing thermocleavable alkyl ester side chains are introduced on the polymer backbone. The side chains make the polymer soluble in organic solvents and allow film formation via solution processing. Subsequently they can be removed by heating in a post-processing step forming a harder insoluble material with enhanced stability. These new thermocleavable materials can potentially offer higher chromophore density, higher level processing and improved stability in a solar cell device. Methods are developed for the incorporation of alkoxy chains and thermocleavable ester groups on the benzothiadiazole and the thiophene units in an attempt to evolve the PDTBT system to a more advanced level. The synthesis and photovoltaic applications of the PDTTP and PDTBT systems is described. (author)

  5. All solution processed tandem polymer solar cells based on thermocleavable materials

    DEFF Research Database (Denmark)

    Hagemann, Ole; Bjerring, Morten; Nielsen, Niels Chr.;

    2008-01-01

    Multilayer tandem polymer solar cells were prepared by solution processing using thermocleavable polymer materials that allow for conversion to an insoluble state through a short thermal treatment. The problems associated with solubility during application of subsequent layers in the stack were e...

  6. Thermocleavable π‐Conjugated Polymers – Synthesis and photovoltaic applications

    DEFF Research Database (Denmark)

    Petersen, Martin Helgesen

    Polymer solar cells (plastic solar cells) have seen remarkable improvements in recent years where power conversion efficiencies of up to 6% have been reported for small area devices. However in terms of stability polymer solar cells degrade during illumination and in the dark leading to operational...... (>20000 hours). This Ph.D. thesis describes the synthesis, characterization and photovoltaic applications of these novel polymer materials. A key feature of these materials is that solubilizing thermocleavable alkyl ester side chains are introduced on the polymer backbone. The side chains make the polymer...... soluble in organic solvents and allow film formation via solution processing. Subsequently they can be removed by heating in a post‐processing step forming a harder insoluble material with enhanced stability. These new thermocleavable materials can potentially offer higher chromophore density, higher...

  7. Bear

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The famous physicist made for his scholars this riddle. A fellow encountered a bear in a wasteland. There was nobody else there. Both were frightened and ran away. Fellow to the north, bear to the west. Suddenly the fellow stopped, aimed his gun to the south and shot the bear. What colour was the bear?

  8. Thermocleavable Materials for Polymer Solar Cells with High Open Circuit Voltage-A Comparative Study

    DEFF Research Database (Denmark)

    Tromholt, Thomas; Gevorgyan, Suren; Jørgensen, Mikkel;

    2009-01-01

    The search for polymer solar cells giving a high open circuit voltage was conducted through a comparative study of four types of bulk-heterojunction solar cells employing different photoactive layers. As electron donors the thermo-cleavable polymer poly-(3-(2-methylhexyloxycarbonyl)dithiophene) (P3......MHOCT) and unsubstituted polythiophene (PT) were used, the latter of which results from thermo cleaving the former at 310 °C. As reference, P3HT solar cells were built in parallel. As electron acceptors, either PCBM or bis-[60]PCBM were used. In excess of 300 solar cells were produced under as identical...... conditions as possible, varying only the material combination of the photo active layer. It was observed that on replacing PCBM with bis[60]PCBM, the open circuit voltage on average increased by 100 mV for P3MHOCT and 200 mV for PT solar cells. Open circuit voltages approaching 1 V were observed for the PT...

  9. Thermo-cleavable solvents for printing conjugated polymers: Application in polymer solar cells

    DEFF Research Database (Denmark)

    Jørgensen, Mikkel; Hagemann, Ole; Alstrup, Jan;

    2009-01-01

    large-scale production of polymer solar cells using screen printing. Screen-printed solar cells are still very inferior to state of the art P3HT/PCBM technology, but it is our view that it is necessary to explore these printing technologies if polymer solar cells are to ever become commercial products.......The synthesis and characterization of a number of so-called thermo-cleavable solvents are described with their application in all-air, all-solution and all-screen-printed polymer solar cells. These solvents were developed to meet some requirements for printing techniques such as long “open time...... (TGA) and high-temperature NMR established the onset temperature of decomposition, the rate of the reaction and the nature of the products. Printing experiments with inks based on these solvents together with conjugated polymers are exemplified for polymer solar cell devices to show how they enable...

  10. All solution processed tandem polymer solar cells based on thermocleavable materials

    Energy Technology Data Exchange (ETDEWEB)

    Hagemann, Ole; Krebs, Frederik C. [Risoe National Laboratory for Sustainable Energy, Polymer Department, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Bjerring, Morten; Nielsen, Niels Chr. [Center for Insoluble Protein Structures, Interdisciplinary Nanoscience Center (iNANO) and Department of Chemistry, University of Aarhus, DK-8000 Aarhus C (Denmark)

    2008-11-15

    Multilayer tandem polymer solar cells were prepared by solution processing using thermocleavable polymer materials that allow for conversion to an insoluble state through a short thermal treatment. The problems associated with solubility during application of subsequent layers in the stack were efficiently solved. Devices comprised a transparent front cathode based on solution processed zinc oxide nanoparticles, a large band gap active layer based on a bulk heterojunction between zinc oxide and poly(3-carboxydithiophene) (P3CT) followed by a layer of PEDOT:PSS processed from water. The second cell in the stack employed a zinc oxide front cathode processed on top of the PEDOT:PSS layer from an organic solvent, a low band gap active layer based on a bulk heterojunction between zinc oxide and the novel poly(carboxyterthiophene-co-diphenylthienopyrazine) (P3CTTP) followed by a layer of PEDOT:PSS again processed from water and finally a printed silver electrode. The devices were prepared without the use of fullerenes and vacuum steps and employ only thermal treatments and orthogonal solvents. The devices exhibited operational stability in air without any form of encapsulation. (author)

  11. The Diels Alder/retro-Diels Alder concept on solid support : a study of the scope, limitations and conceivable applications as a traceless thermocleavable linker

    NARCIS (Netherlands)

    Gieling, Reinerus Gerardus

    2003-01-01

    This thesis deals with the conceivable transfer of the Diels Alder/retro-Diels Alder concept to the solid phase in order to broaden the scope of the methodology to a combinatorial level. In addition, based on this methodology the development of a traceless thermocleavable linking system for Solid-Ph

  12. Thermocleavable materials for polymer solar cells with high open circuit voltage-a comparative study.

    Science.gov (United States)

    Tromholt, Thomas; Gevorgyan, Suren A; Jørgensen, Mikkel; Krebs, Frederik C; Sylvester-Hvid, Kristian O

    2009-12-01

    The search for polymer solar cells giving a high open circuit voltage was conducted through a comparative study of four types of bulk-heterojunction solar cells employing different photoactive layers. As electron donors the thermo-cleavable polymer poly-(3-(2-methylhexyloxycarbonyl)dithiophene) (P3MHOCT) and unsubstituted polythiophene (PT) were used, the latter of which results from thermo cleaving the former at 310 degrees C. As reference, P3HT solar cells were built in parallel. As electron acceptors, either PCBM or bis-[60]PCBM were used. In excess of 300 solar cells were produced under as identical conditions as possible, varying only the material combination of the photo active layer. It was observed that on replacing PCBM with bis[60]PCBM, the open circuit voltage on average increased by 100 mV for P3MHOCT and 200 mV for PT solar cells. Open circuit voltages approaching 1 V were observed for the PT:bis[60]PCBM solar cells and a maximum conversion efficiency of 1.3% was obtained for solar cells with P3MHOCT:PCBM as the photoactive material. For the reference solar cells maximum efficiencies of 2.1 and 2.4% were achieved for P3HT:PCBM and P3HT:bis[60]PCBM, respectively. Despite special measures taken in terms of substrate design and device processing, a substantial spread in the photovoltaic properties was generally observed. This spread could not be correlated with the optical properties of the solar cells, the thickness of the photo active layer or the electrode deposition conditions of the aluminum top electrode. PMID:20356155

  13. Conductive iron oxide minerals accelerate syntrophic cooperation in methanogenic benzoate degradation

    International Nuclear Information System (INIS)

    Highlights: • Paddy soil contaminated with benzoate incubated with hematite and magnetite. • Iron oxides addition enhanced methanogenic benzoate degradation by 25–53%. • The facilitated syntrophy might involve direct interspecies electron transfer. • Bacillaceae, Peptococcaceae, and Methanobacterium are potentially involved. - Abstract: Recent studies have suggested that conductive iron oxide minerals can facilitate syntrophic metabolism of the methanogenic degradation of organic matter, such as ethanol, propionate and butyrate, in natural and engineered microbial ecosystems. This enhanced syntrophy involves direct interspecies electron transfer (DIET) powered by microorganisms exchanging metabolic electrons through electrically conductive minerals. Here, we evaluated the possibility that conductive iron oxides (hematite and magnetite) can stimulate the methanogenic degradation of benzoate, which is a common intermediate in the anaerobic metabolism of aromatic compounds. The results showed that 89–94% of the electrons released from benzoate oxidation were recovered in CH4 production, and acetate was identified as the only carbon-bearing intermediate during benzoate degradation. Compared with the iron-free controls, the rates of methanogenic benzoate degradation were enhanced by 25% and 53% in the presence of hematite and magnetite, respectively. This stimulatory effect probably resulted from DIET-mediated methanogenesis in which electrons transfer between syntrophic partners via conductive iron minerals. Phylogenetic analyses revealed that Bacillaceae, Peptococcaceae, and Methanobacterium are potentially involved in the functioning of syntrophic DIET. Considering the ubiquitous presence of iron minerals within soils and sediments, the findings of this study will increase the current understanding of the natural biological attenuation of aromatic hydrocarbons in anaerobic environments

  14. The Diels Alder/retro-Diels Alder concept on solid support : a study of the scope, limitations and conceivable applications as a traceless thermocleavable linker

    OpenAIRE

    Gieling, Reinerus Gerardus

    2003-01-01

    This thesis deals with the conceivable transfer of the Diels Alder/retro-Diels Alder concept to the solid phase in order to broaden the scope of the methodology to a combinatorial level. In addition, based on this methodology the development of a traceless thermocleavable linking system for Solid-Phase Organic Synthesis (SPOS) is described. As a possible application of this linker system, the solid-phase synthesis of precursors of pharmaceutically interesting CNS-active heterocyclic compounds...

  15. The Role of Benzoate in Anaerobic Degradation of Terephthalate

    OpenAIRE

    Kleerebezem, Robbert; Pol, Look W. Hulshoff; Lettinga, Gatze

    1999-01-01

    The effects of acetate, benzoate, and periods without substrate on the anaerobic degradation of terephthalate (1,4-benzene-dicarboxylate) by a syntrophic methanogenic culture were studied. The culture had been enriched on terephthalate and was capable of benzoate degradation without a lag phase. When incubated with a mixture of benzoate and terephthalate, subsequent degradation with preference for benzoate was observed. Both benzoate and acetate inhibited the anaerobic degradation of terephth...

  16. Conductive iron oxide minerals accelerate syntrophic cooperation in methanogenic benzoate degradation

    Energy Technology Data Exchange (ETDEWEB)

    Zhuang, Li; Tang, Jia; Wang, Yueqiang; Hu, Min; Zhou, Shungui, E-mail: sgzhou@soil.gd.cn

    2015-08-15

    Highlights: • Paddy soil contaminated with benzoate incubated with hematite and magnetite. • Iron oxides addition enhanced methanogenic benzoate degradation by 25–53%. • The facilitated syntrophy might involve direct interspecies electron transfer. • Bacillaceae, Peptococcaceae, and Methanobacterium are potentially involved. - Abstract: Recent studies have suggested that conductive iron oxide minerals can facilitate syntrophic metabolism of the methanogenic degradation of organic matter, such as ethanol, propionate and butyrate, in natural and engineered microbial ecosystems. This enhanced syntrophy involves direct interspecies electron transfer (DIET) powered by microorganisms exchanging metabolic electrons through electrically conductive minerals. Here, we evaluated the possibility that conductive iron oxides (hematite and magnetite) can stimulate the methanogenic degradation of benzoate, which is a common intermediate in the anaerobic metabolism of aromatic compounds. The results showed that 89–94% of the electrons released from benzoate oxidation were recovered in CH{sub 4} production, and acetate was identified as the only carbon-bearing intermediate during benzoate degradation. Compared with the iron-free controls, the rates of methanogenic benzoate degradation were enhanced by 25% and 53% in the presence of hematite and magnetite, respectively. This stimulatory effect probably resulted from DIET-mediated methanogenesis in which electrons transfer between syntrophic partners via conductive iron minerals. Phylogenetic analyses revealed that Bacillaceae, Peptococcaceae, and Methanobacterium are potentially involved in the functioning of syntrophic DIET. Considering the ubiquitous presence of iron minerals within soils and sediments, the findings of this study will increase the current understanding of the natural biological attenuation of aromatic hydrocarbons in anaerobic environments.

  17. 21 CFR 582.3733 - Sodium benzoate.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Sodium benzoate. 582.3733 Section 582.3733 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL DRUGS, FEEDS, AND RELATED PRODUCTS SUBSTANCES GENERALLY RECOGNIZED AS SAFE Chemical Preservatives §...

  18. Influence of the Annealing Temperature on the Photovoltaic Performance and Film Morphology Applying Novel Thermocleavable Materials

    DEFF Research Database (Denmark)

    Petersen, Martin Helgesen; Bjerring, Morten; Nielsen, Niels Chr.;

    2010-01-01

    a weight loss around 200 °C corresponding to elimination of the ester side chains followed by a second weight loss around 300 °C corresponding to loss of CO2 via decarboxylation. The temperature of thermocleavage of the active layer films was optimized to 265 °C whereby the T2:PCBM solar cells maintained......Di-2-thienyl-2,1,3-benzothiadiazole (DTBT) bearing thermally cleavable ester groups in different positions were prepared and copolymerized with alkylsubstituted cyclopentadithiophene (CPDT). The polymers were found to have band gaps in the range of 1.66−2.03 eV and were explored in polymer...... efficiencies of up to 1.92% were observed for polymers bearing ester groups on the 4-positions of the thienyl groups (T2), but shifting them to the 3-positions (T1) reduced the efficiency significantly to 0.18%. The thermal behavior of the polymers was studied with thermogravimetric analysis (TGA) that showed...

  19. Thermal Decomposition Behavior of Melaminium Benzoate Dihydrate

    OpenAIRE

    N. Kanagathara; M. K. Marchewka; Pawlus, K.; S. Gunasekaran; G. Anbalagan

    2013-01-01

    Crystals of melaminium benzoate dihydrate (MBDH) have been grown from aqueous solution by slow solvent evaporation method at room temperature. Powder X-ray diffraction analysis confirms that MBDH crystallizes in the monoclinic system (C2/c). Thermal decomposition behavior of MBDH has been studied by thermogravimetric analysis at three different heating rates: 10, 15, and 20°C/min. Nonisothermal studies of MBDH revealed that the decomposition occurs in three stages. The values of effective act...

  20. Anaerobic degradation of benzoate by sulfate-reducing bacteria

    Energy Technology Data Exchange (ETDEWEB)

    Silva, S.P.; Adorno, M.A.T.; Moraes, E.M.; Varesche, M.B.A. [Sao Paulo Univ., Sao Carlos, SP (Brazil). Biological Processes Laboratory

    2004-07-01

    Anaerobic processes are an efficient way to degrade aromatic compounds in industrial wastewater, such as phenol, cresol and benzoate. This study characterized the bacteria that degrades benzoate, an anaerobic degradation intermediate of several complex aromatic compounds. In particular, the study assessed the capacity to use benzoate with sulfate reducing bacteria in mesophilic conditions. Biofilm from polyurethane foam matrices of a fixed bed reactor was used as the cellular inoculum to treat industrial wastewater containing organic peroxide. Dilution techniques were used to purify the material and obtain cultures of cocci. The benzoate consumption capacity in sulfidogenic conditions was observed when the purified inoculum was applied to batch reactors with different benzoate/sulfate relations. Results indicate that purification was positive to bacteria that can degrade aromatic compounds. Desulfococcus multivorans bacteria was identified following the physiologic and kinetic experiments. The 0.6 benzoate/sulfate relation was considered ideal for complete consumption of carbon and total use of sulfur. 10 refs., 3 figs.

  1. Sodium benzoate and potassium sorbate preservatives in Iranian doogh.

    Science.gov (United States)

    Zamani Mazdeh, F; Esmaeili Aftabdari, F; Moradi-Khatoonabadi, Z; Shaneshin, M; Torabi, P; Shams Ardekani, M R; Hajimahmoodi, M

    2014-01-01

    Sodium benzoate and potassium sorbate are two common preservatives used in Iran, yet use of these preservatives in doogh (Iranian dairy-based drink) is forbidden according to national standards. The aim of this study was to consider the presence of these preservatives in doogh by high-performance liquid chromatography with UV detection (HPLC-UV). The method was performed using a C18 column and detection at 225 nm. The mobile phase contained ammonium acetate buffer (pH = 4.2) and acetonitrile (80:20 v/v). The survey included 130 samples of doogh for identification and quantification of the named preservatives. All samples contained sodium benzoate, but potassium sorbate was detected in only 13% of them. The means of benzoate and sorbate were 21.3 ± 2.7 and 13.3 ± 39.6 mg kg(-1), respectively. The limits of detection were 2 and 40 ng g(-1) for benzoate and sorbate, respectively. Results indicate that sodium benzoate may occur in doogh naturally.

  2. Sodium benzoate and potassium sorbate preservatives in Iranian doogh.

    Science.gov (United States)

    Zamani Mazdeh, F; Esmaeili Aftabdari, F; Moradi-Khatoonabadi, Z; Shaneshin, M; Torabi, P; Shams Ardekani, M R; Hajimahmoodi, M

    2014-01-01

    Sodium benzoate and potassium sorbate are two common preservatives used in Iran, yet use of these preservatives in doogh (Iranian dairy-based drink) is forbidden according to national standards. The aim of this study was to consider the presence of these preservatives in doogh by high-performance liquid chromatography with UV detection (HPLC-UV). The method was performed using a C18 column and detection at 225 nm. The mobile phase contained ammonium acetate buffer (pH = 4.2) and acetonitrile (80:20 v/v). The survey included 130 samples of doogh for identification and quantification of the named preservatives. All samples contained sodium benzoate, but potassium sorbate was detected in only 13% of them. The means of benzoate and sorbate were 21.3 ± 2.7 and 13.3 ± 39.6 mg kg(-1), respectively. The limits of detection were 2 and 40 ng g(-1) for benzoate and sorbate, respectively. Results indicate that sodium benzoate may occur in doogh naturally. PMID:24914596

  3. Synthesis and Crystal Structure of Tetranuclear Zinc Benzoate

    Institute of Scientific and Technical Information of China (English)

    YIN Ming-cai; WANG Chi-wei; AI Chang-chun; YUAN Liang-jie; SUN Ju-tang

    2004-01-01

    A tetranuclear zinc benzoate Zn4O(C6H5CO2)6 was synthesized and characterized by X-ray single crystal determination. It crystallizes in cubic, space group Ia-3d. Its crystal cell is very large, a=4.100 63(18) nm, V=68.953(5) nm3 and Z = 48. The structure is composed of discrete Zn4O(C6H5CO2)6 molecules. In each molecule, four zinc atoms are held together by a central oxygen atom, which results in the formation of a regular tetrahedron. All benzoate ligands coordinate to zinc atoms in a bidentate bridging mode. Each zinc atom is in a slightly distorted tetrahedral geometry, coordinated by three benzoate oxygen atoms and the central oxygen atom. The intermolecular interactions result in the formation of a three-dimensional supramolecular framework, with non-intersecting parallel channels.

  4. Bearing system

    Science.gov (United States)

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  5. ISOLATION AND CHARACTERIZATION OF A NOVEL BENZOATE- UTILIZING Serratia marcescens

    Directory of Open Access Journals (Sweden)

    ANTONIUS SUWANTO

    2003-01-01

    Full Text Available A new benzoate-utilizing strain, Serratia marcescens DS-8, isolated from the environment was characterized. The strain was enterobacilli, Gram negative, mesophilic, non ha lophilic, and aerobic bacterium that showed motile ovale-rod shaped cells. The isolate produced extracellular chitinase, protease, and prodigiosin (a red pigment pr oduced by several Serratia strains yielding bright red or pink colonies. A physiological assay using Microbact* test showed that the strain was closely related to Klebsiella ozaenae (49.85% and Serratia liquefaciens (24.42%, respectively. However, 16S rRNA sequence analysis indicated that the strain was closely related to S. marcescens DSM 30121 with similarity level of 98%. DS-8 strain was able to synthesize its own vitamins. Optimum growth in benzoate was obtained at pH between 7-8.5 and NaCl concentration of 1- 1.5% (w/v. The isolate could grow in benzoate-containing medium up to 10 mM. Other carbon sources that could support the growth of DS-8 were casamino acid, glutamate, glucose, acetate, potato star ch, and ethanol.

  6. Anaphylaxis Triggered by Benzyl Benzoate in a Preparation of Depot Testosterone Undecanoate

    OpenAIRE

    Ong, Gregory S. Y.; Somerville, Colin P.; Jones, Timothy W; Walsh, John P.

    2012-01-01

    We report the first case of an anaphylactic reaction to Reandron 1000 (depot testosterone undecanoate with a castor oil and benzyl benzoate vehicle). While considered to have a favourable safety profile, serious complications such as oil embolism and anaphylaxis can occur. In our patient, skin testing identified benzyl benzoate to be the trigger, with no reaction to castor oil or testosterone undecanoate components. As benzyl benzoate exists in multiple pharmaceuticals, foods, and cosmetics, ...

  7. Analisa Pengawet Natrium Benzoat Pada Manisan Buah Di Pasar Tradisional Kota Medan Tahun 2010.

    OpenAIRE

    Amalia Kurnia Sari P

    2011-01-01

    Preservative sodium benzoate chemical with formula of C7H5O2 This research was a descriptive survey researched that analyzed the content of sodium benzoate on the candied fruit. Fruit with total sampling 12 sample candied fruit consisting of three kinds of fruit, salak, mango and kedondong. Primary data from this research were obtained from laboratory test on sodium benzoate preservative substences contained in the candied fruit. Data obtained were analyzed descriptively. Na were Substance...

  8. A Moessbauer study of the thermal behaviour of iron(III) benzoate

    International Nuclear Information System (INIS)

    The thermal behaviour of three different iron(III) benzoate complexes was investigated by Moessbauer spectroscopy, conventional thermal analysis and infrared spectroscopy. Each of the complexes had six benzoate ligands within the first coordination sphere. Their Moessbauer spectra showed only quadrupole pattern, characteristic of high-spin iron(III). When the complexes were heated in air, two new iron(III) benzoate complexes were obtained, having five and four benzoate ligands within the first coordination sphere. The Moessbauer spectra of these new complexes showed two distinct quadrupole petterns with relative concentration close to 2:1, which could be related to the nonequivalence of the three iron ions in the molecule. (author)

  9. Journal bearing

    Science.gov (United States)

    Menke, John R.; Boeker, Gilbert F.

    1976-05-11

    1. An improved journal bearing comprising in combination a non-rotatable cylindrical bearing member having a first bearing surface, a rotatable cylindrical bearing member having a confronting second bearing surface having a plurality of bearing elements, a source of lubricant adjacent said bearing elements for supplying lubricant thereto, each bearing element consisting of a pair of elongated relatively shallowly depressed surfaces lying in a cylindrical surface co-axial with the non-depressed surface and diverging from one another in the direction of rotation and obliquely arranged with respect to the axis of rotation of said rotatable member to cause a flow of lubricant longitudinally along said depressed surfaces from their distal ends toward their proximal ends as said bearing members are rotated relative to one another, each depressed surface subtending a radial angle of less than 360.degree., and means for rotating said rotatable bearing member to cause the lubricant to flow across and along said depressed surfaces, the flow of lubricant being impeded by the non-depressed portions of said second bearing surface to cause an increase in the lubricant pressure.

  10. Environmental fate of emamectin benzoate after tree micro injection of horse chestnut trees.

    Science.gov (United States)

    Burkhard, Rene; Binz, Heinz; Roux, Christian A; Brunner, Matthias; Ruesch, Othmar; Wyss, Peter

    2015-02-01

    Emamectin benzoate, an insecticide derived from the avermectin family of natural products, has a unique translocation behavior in trees when applied by tree micro injection (TMI), which can result in protection from insect pests (foliar and borers) for several years. Active ingredient imported into leaves was measured at the end of season in the fallen leaves of treated horse chestnut (Aesculus hippocastanum) trees. The dissipation of emamectin benzoate in these leaves seems to be biphasic and depends on the decomposition of the leaf. In compost piles, where decomposition of leaves was fastest, a cumulative emamectin benzoate degradation half-life time of 20 d was measured. In leaves immersed in water, where decomposition was much slower, the degradation half-life time was 94 d, and in leaves left on the ground in contact with soil, where decomposition was slowest, the degradation half-life time was 212 d. The biphasic decline and the correlation with leaf decomposition might be attributed to an extensive sorption of emamectin benzoate residues to leaf macromolecules. This may also explain why earthworms ingesting leaves from injected trees take up very little emamectin benzoate and excrete it with the feces. Furthermore, no emamectin benzoate was found in water containing decomposing leaves from injected trees. It is concluded, that emamectin benzoate present in abscised leaves from horse chestnut trees injected with the insecticide is not available to nontarget organisms present in soil or water bodies. PMID:25363584

  11. Method for estimating S(N)1 rate constants: solvolytic reactivity of benzoates.

    Science.gov (United States)

    Matić, Mirela; Denegri, Bernard; Kronja, Olga

    2012-10-19

    Nucleofugalities of pentafluorobenzoate (PFB) and 2,4,6-trifluorobenzoate (TFB) leaving groups have been derived from the solvolysis rate constants of X,Y-substituted benzhydryl PFBs and TFBs measured in a series of aqueous solvents, by applying the LFER equation: log k = s(f)(E(f) + N(f)). The heterolysis rate constants of dianisylmethyl PFB and TFB, and those determined for 10 more dianisylmethyl benzoates in aqueous ethanol, constitute a set of reference benzoates whose experimental ΔG(‡) have been correlated with the ΔH(‡) (calculated by PCM quantum-chemical method) of the model epoxy ring formation. Because of the excellent correlation (r = 0.997), the method for calculating the nucleofugalities of substituted benzoate LGs have been established, ultimately providing a method for determination of the S(N)1 reactivity for any benzoate in a given solvent. Using the ΔG(‡) vs ΔH(‡) correlation, and taking s(f) based on similarity, the nucleofugality parameters for about 70 benzoates have been determined in 90%, 80%, and 70% aqueous ethanol. The calculated intrinsic barriers for substituted benzoate leaving groups show that substrates producing more stabilized LGs proceed over lower intrinsic barriers. Substituents on the phenyl ring affect the solvolysis rate of benzhydryl benzoates by both field and inductive effects. PMID:22973993

  12. Environmental fate of emamectin benzoate after tree micro injection of horse chestnut trees.

    Science.gov (United States)

    Burkhard, Rene; Binz, Heinz; Roux, Christian A; Brunner, Matthias; Ruesch, Othmar; Wyss, Peter

    2015-02-01

    Emamectin benzoate, an insecticide derived from the avermectin family of natural products, has a unique translocation behavior in trees when applied by tree micro injection (TMI), which can result in protection from insect pests (foliar and borers) for several years. Active ingredient imported into leaves was measured at the end of season in the fallen leaves of treated horse chestnut (Aesculus hippocastanum) trees. The dissipation of emamectin benzoate in these leaves seems to be biphasic and depends on the decomposition of the leaf. In compost piles, where decomposition of leaves was fastest, a cumulative emamectin benzoate degradation half-life time of 20 d was measured. In leaves immersed in water, where decomposition was much slower, the degradation half-life time was 94 d, and in leaves left on the ground in contact with soil, where decomposition was slowest, the degradation half-life time was 212 d. The biphasic decline and the correlation with leaf decomposition might be attributed to an extensive sorption of emamectin benzoate residues to leaf macromolecules. This may also explain why earthworms ingesting leaves from injected trees take up very little emamectin benzoate and excrete it with the feces. Furthermore, no emamectin benzoate was found in water containing decomposing leaves from injected trees. It is concluded, that emamectin benzoate present in abscised leaves from horse chestnut trees injected with the insecticide is not available to nontarget organisms present in soil or water bodies.

  13. Effects of sodium benzoate, a widely used food preservative, on glucose homeostasis and metabolic profiles in humans.

    Science.gov (United States)

    Lennerz, Belinda S; Vafai, Scott B; Delaney, Nigel F; Clish, Clary B; Deik, Amy A; Pierce, Kerry A; Ludwig, David S; Mootha, Vamsi K

    2015-01-01

    Sodium benzoate is a widely used preservative found in many foods and soft drinks. It is metabolized within mitochondria to produce hippurate, which is then cleared by the kidneys. We previously reported that ingestion of sodium benzoate at the generally regarded as safe (GRAS) dose leads to a robust excursion in the plasma hippurate level [1]. Since previous reports demonstrated adverse effects of benzoate and hippurate on glucose homeostasis in cells and in animal models, we hypothesized that benzoate might represent a widespread and underappreciated diabetogenic dietary exposure in humans. Here, we evaluated whether acute exposure to GRAS levels of sodium benzoate alters insulin and glucose homeostasis through a randomized, controlled, cross-over study of 14 overweight subjects. Serial blood samples were collected following an oral glucose challenge, in the presence or absence of sodium benzoate. Outcome measurements included glucose, insulin, glucagon, as well as temporal mass spectrometry-based metabolic profiles. We did not find a statistically significant effect of an acute oral exposure to sodium benzoate on glucose homeostasis. Of the 146 metabolites targeted, four changed significantly in response to benzoate, including the expected rise in benzoate and hippurate. In addition, anthranilic acid, a tryptophan metabolite, exhibited a robust rise, while acetylglycine dropped. Although our study shows that GRAS doses of benzoate do not have an acute, adverse effect on glucose homeostasis, future studies will be necessary to explore the metabolic impact of chronic benzoate exposure.

  14. Preparation and Evaluation of Emamectin Benzoate Solid Microemulsion

    Directory of Open Access Journals (Sweden)

    Lei Feng

    2016-01-01

    Full Text Available The solid microemulsions of emamectin benzoate with the same content of surfactants were prepared by a self-emulsifying method. Emulsifier 600# and emulsifier 700# (3/2, w/w screened from eleven kinds of commonly used surfactants displayed great emulsifying properties. The redispersed solution of the solid microemulsion presented aqueous microemulsion characteristic. The mean particle size and polydispersity index were 10.34 ± 0.10 nm and 0.283 ± 0.013, respectively. The solid microemulsion showed excellent storage stability and the bioassay compared with water dispersible granules against diamondback moths provided a proof of its improved biological activities. This formulation could significantly reduce surfactants and is perspective in plant protection for improving bioavailability and environmental friendliness.

  15. 2-(1,3-Benzoxazol-2-yl-1-phenylethenyl benzoate

    Directory of Open Access Journals (Sweden)

    Mohammad Hassan Ghorbani

    2011-10-01

    Full Text Available In the title molecule, C22H15NO3, the configuration about the ethylenic double bond is Z configuration and it is approximately coplanar with the adjacent phenyl ring and benzoxazole ring system as indicated by the C(H=C(O—Cphenyl—Cphenyl and Obenzoxazole—C—C(H=C(O torsion angles of 179.88 (15 and 5.7 (2°, respectively. The dihedral angle between the essentially planar (r.m.s. deviation = 0.080 Å 2-(1,3-benzoxazol-2-yl-1-phenylethenyl group and the benzoate phenyl ring is 61.51 (6°. A short intramolecular O...O non-bonded interaction of 2.651 (2 Å is present.

  16. [Reductive Dechlorination of Trichloroethylene by Benzoate-Enriched Anaerobic Cultures].

    Science.gov (United States)

    Li, Jiang-wei; Yang, Xiao-yong; Hu, An-yi; Yu, Chang-ping

    2015-10-01

    Gas chromatography was used to monitor the reductive dechlorination of trichloroethylene (TCE) by anaerobic enrichment cultures with benzoate as the sole carbon source. The 454 pyrosequencing technique was used to investigate the microbial community and the real-time quantitative PCR was used to quantify the gene copies of Dehalococcoides spp. (DHC). The results showed that TCE was dechlorinated to vinyl chloride along with the formation of methane in 94 days. The anaerobic enrichment cultures exhibited a high diversity, which were classified into 16 phyla, 33 classes, 52 orders, 88 families and 129 genera, while 51.2% of them belonged to unclassified group, which inferred that there were a large portion of bacteria with unknown functional in this system. Degradation of TCE was accomplished by reductive dechlorinating and other functional populations, and the DHC which carried tceA gene could be the dominant reductive dechlorinating populations in the system. PMID:26841609

  17. Anaphylaxis Triggered by Benzyl Benzoate in a Preparation of Depot Testosterone Undecanoate

    Directory of Open Access Journals (Sweden)

    Gregory S. Y. Ong

    2012-01-01

    Full Text Available We report the first case of an anaphylactic reaction to Reandron 1000 (depot testosterone undecanoate with a castor oil and benzyl benzoate vehicle. While considered to have a favourable safety profile, serious complications such as oil embolism and anaphylaxis can occur. In our patient, skin testing identified benzyl benzoate to be the trigger, with no reaction to castor oil or testosterone undecanoate components. As benzyl benzoate exists in multiple pharmaceuticals, foods, and cosmetics, individual components of pharmaceuticals should be tested when investigating drug allergies. Doctors should be alert to the potential for serious reactions to any of the components of Reandron 1000.

  18. GAS BEARING

    Science.gov (United States)

    Skarstrom, C.W.

    1960-09-01

    A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

  19. Grizzly bear

    Science.gov (United States)

    Schwartz, C.C.; Miller, S.D.; Haroldson, M.A.; Feldhamer, G.; Thompson, B.; Chapman, J.

    2003-01-01

    The grizzly bear inspires fear, awe, and respect in humans to a degree unmatched by any other North American wild mammal. Like other bear species, it can inflict serious injury and death on humans and sometimes does. Unlike the polar bear (Ursus maritimus) of the sparsely inhabited northern arctic, however, grizzly bears still live in areas visited by crowds of people, where presence of the grizzly remains physically real and emotionally dominant. A hike in the wilderness that includes grizzly bears is different from a stroll in a forest from which grizzly bears have been purged; nighttime conversations around the campfire and dreams in the tent reflect the presence of the great bear. Contributing to the aura of the grizzly bear is the mixture of myth and reality about its ferocity. unpredictable disposition, large size, strength, huge canines, long claws, keen senses, swiftness, and playfulness. They share characteristics with humans such as generalist life history strategies. extended periods of maternal care, and omnivorous diets. These factors capture the human imagination in ways distinct from other North American mammals. Precontact Native American legends reflected the same fascination with the grizzly bear as modern stories and legends (Rockwell 1991).

  20. Kinetic Evidence for the Solvent Intervention in the Solvolysis of Tertiary Benzylic Benzoates

    Institute of Scientific and Technical Information of China (English)

    LIU,Kwang-Ting; CHANG,Lih-Wei; CHIN,Chien-Pu

    2006-01-01

    Rates of solvolyses of 2-(4-methylphenyl)-2-propyl benzoate (2b), 2-(4-methylthiophenyl)-2-propyl benzoate (3b) and 2,2-dimethyl-1-(4-methoxyphenyl)-1-phenyl-1-propyl benzoate (4b) were measured, respectively, in ten or more different solvent systems. Additional YBnOPNB and YxBnOPNB values in binary trifluoroethanol-water systems were determined. Grunwald-Winstein type correlation analysis showed that YBnOPNB values were applicable to benzylic benzoates. The rate ratio, kOPNB/kOBz, was found to be solvent-dependent in the range of 29 for 4 in ethanol to 4 for 2 in trifluoroethanol-water. Non-limiting mechanism, including both nucleophilic and electrophilic solvent assistance, in the solvolysis of 2b was discussed.

  1. Synthesis of methyl benzoate by methoxycarbonylation of acetophenone with dimethyl carbonate over solid base catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Dudu; Chang, Wenming; Wen, Xia [State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan, 030001 (China); Graduate University of Chinese Academy of Sciences, Beijing, 100039 (China); Xiao, Fukui; Li, Junping; Zhao, Ning; Wei, Wei; Sun, Yuhan [State Key Laboratory of Coal Conversion, Institute of Coal Chemistry, Chinese Academy of Sciences, Taiyuan, 030001 (China)

    2008-08-15

    A convenient and simple route for synthesis of methyl benzoate from dimethyl carbonate and acetophenone has been exploited for the first time in the presence of solid base catalysts. The results showed that solid base with moderate strength, such as MgO, facilitated the formation of methyl benzoate and the function of basic catalysts could mainly be attributed to the activation of ketone via the abstraction of H{sup {alpha}} by base sites. (author)

  2. Formulation and evaluation of fast dissolving sublingual films of Rizatriptan Benzoate

    OpenAIRE

    Bhyan Bhupinder; Jangra Sarita

    2012-01-01

    Rizatriptan Benzoate, a serotonin 5-HT1 receptor agonist is a new generation antimigraine drug which has oral bioavailability of 47% due to hepatic first pass metabolism. The present study investigated the possibility of developing Rizatriptan benzoate fast dissolving sublingual films allowing fast, reproducible drug dissolution in the oral cavity, thus bypassing first pass metabolism to provide rapid onset of action of the drug. The fast dissolving films were prepared by solvent casting meth...

  3. Synthesis and structure of linear hexanuclear manganese (Ⅱ) benzoate cluster

    Institute of Scientific and Technical Information of China (English)

    陈昌能; 陈久桐; 朱红平; 黄子祥; 刘秋田

    2001-01-01

    From a reaction system including benzoic acid and Mn(NO3)2 in alkali medium, two hexanuclear manganese benzoate cluster compounds have been synthesized. A compound [Et4N]2[Mn6(PhCOO)14] has been structurally characterized, which contains hexanuclear Mn11 moieties extending unlimitedly to form one-dimensional linear structure. Carboxyl oxygen atoms are bridged in variety of modes to the Mn atoms, forming an arrangement like a sinusoid for the Mn atoms. The structural parameters of these compounds were compared with the data obtained from EXAFS determination for the Mn cluster in the OEC of PS11, supporting that the coordination sphere of the Mn site in the OEC may contain carboxyl bridges. The possible combination modes between the carboxyl group and the Mn atoms have been suggested. The NMR signals exhibit widening and shift produced by the influence of the paramagnetic Mn" sites. The red-shift of the absorption in IR spectrum was observed to be attributed to the coordination of the carboxyl group to the Mn

  4. Foil bearings

    Science.gov (United States)

    Elrod, David A.

    1993-11-01

    The rolling element bearings (REB's) which support many turbomachinery rotors offer high load capacity, low power requirements, and durability. Two disadvantages of REB's are: (1) rolling or sliding contact within the bearing has life-limiting consequences; and (2) REB's provide essentially no damping. The REB's in the Space Shuttle Main Engine (SSME) turbopumps must sustain high static and dynamic loads, at high speeds, with a cryogenic fluid as lubricant and coolant. The pump end ball bearings limit the life of the SSME high pressure oxygen turbopump (HPOTP). Compliant foil bearing (CFB) manufacturers have proposed replacing turbopump REB's with CFB's CFB's work well in aircraft air cycle machines, auxiliary power units, and refrigeration compressors. In a CFB, the rotor only contracts the foil support structure during start up and shut down. CFB damping is higher than REB damping. However, the load capacity of the CFB is low, compared to a REB. Furthermore, little stiffness and damping data exists for the CFB. A rotordynamic analysis for turbomachinery critical speeds and stability requires the input of bearing stiffness and damping coefficients. The two basic types of CFB are the tension-dominated bearing and the bending-dominated bearing. Many investigators have analyzed and measured characteristics of tension-dominated foil bearings, which are applied principally in magnetic tape recording. The bending-dominated CFB is used more in rotating machinery. This report describes the first phase of a structural analysis of a bending-dominated, multileaf CFB. A brief discussion of CFB literature is followed by a description and results of the present analysis.

  5. Expression, purification and kinetic characterization of recombinant benzoate dioxygenase from Rhodococcus ruber UKMP-5M

    Directory of Open Access Journals (Sweden)

    Arezoo Tavakoli

    2016-09-01

    Full Text Available In this study, benzoate dioxygenase from Rhodococcus ruber UKMP-5M was catalyzed by oxidating the benzene ring to catechol and other derivatives. The benzoate dioxygenase (benA gene from Rhodococcus ruber UKMP-5M was then expressed, purified, characterized, The benA gene was amplified (642 bp, and the product was cloned into a pGEM-T vector.The recombinant plasmid pGEMT-benA was digested by double restriction enzymes BamHI and HindIII to construct plasmid pET28b-benA and was then ligated into Escherichia coli BL21 (DE3. The recombinant E. coli was induced with 0.5 mM isopropyl β-D-thiogalactoside (IPTG at 22˚C to produce benzoate dioxygenase. The enzyme was then purified by ion exchange chromatography after 8 purification folds. The resulting product was 25 kDa, determined by sodium dodecyl sulphate polyacrylamide gel electrophoresis (SDS-PAGE and western blotting. Benzoate dioxygenase activity was found to be 6.54 U/mL and the optimal pH and temperature were 8.5 and 25°C, respectively. Maximum velocity (Vmax and Michaelis constant (Km were 7.36 U/mL and 5.58 µM, respectively. The end metabolite from the benzoate dioxygenase reaction was cyclohexane dione, which was determined by gas chromatography mass spectrometry (GC-MS.

  6. Sodium benzoate and potassium sorbate preservatives in food stuffs in Iran.

    Science.gov (United States)

    Amirpour, Mansooreh; Arman, Azim; Yolmeh, Ahmad; Akbari Azam, Maryam; Moradi-Khatoonabadi, Zhila

    2015-01-01

    A high-performance liquid chromatography method was applied for the determination of the levels of benzoate and sorbate in 400 food samples, including pickled cucumbers, canned tomato pastes, sour cherry jams, soft drinks, fruit juices and dairy products (UF-Feta cheeses, Lighvan cheeses, lactic cheeses, yogurts and doogh). The results showed that 270 (67.5%) of all samples contained benzoate ranging from 11.9 to 288.5 mg kg(-1) in lactic cheese and fruit juice, respectively. The levels of sorbate in 98 (24.5%) of the samples were 20.1 to 284.3 mg kg(-1) in doogh and fruit juice, respectively. Moreover, benzoate was detected in all dairy products ranging from 11.9 mg kg(-1) in lactic cheese to 91.2 mg kg(-1) in UF-Feta cheese. A low concentration of benzoate could originate naturally, due to specific biochemical mechanisms during cheese, yogurt and doogh maturation. In conclusion, a minimum level for benzoate in dairy products should be defined in the legislation. PMID:25832450

  7. Sodium benzoate and potassium sorbate preservatives in food stuffs in Iran.

    Science.gov (United States)

    Amirpour, Mansooreh; Arman, Azim; Yolmeh, Ahmad; Akbari Azam, Maryam; Moradi-Khatoonabadi, Zhila

    2015-01-01

    A high-performance liquid chromatography method was applied for the determination of the levels of benzoate and sorbate in 400 food samples, including pickled cucumbers, canned tomato pastes, sour cherry jams, soft drinks, fruit juices and dairy products (UF-Feta cheeses, Lighvan cheeses, lactic cheeses, yogurts and doogh). The results showed that 270 (67.5%) of all samples contained benzoate ranging from 11.9 to 288.5 mg kg(-1) in lactic cheese and fruit juice, respectively. The levels of sorbate in 98 (24.5%) of the samples were 20.1 to 284.3 mg kg(-1) in doogh and fruit juice, respectively. Moreover, benzoate was detected in all dairy products ranging from 11.9 mg kg(-1) in lactic cheese to 91.2 mg kg(-1) in UF-Feta cheese. A low concentration of benzoate could originate naturally, due to specific biochemical mechanisms during cheese, yogurt and doogh maturation. In conclusion, a minimum level for benzoate in dairy products should be defined in the legislation.

  8. Hydrodynamic bearings

    CERN Document Server

    Bonneau, Dominique; Souchet, Dominique

    2014-01-01

    This Series provides the necessary elements to the development and validation of numerical prediction models for hydrodynamic bearings. This book describes the rheological models and the equations of lubrication. It also presents the numerical approaches used to solve the above equations by finite differences, finite volumes and finite elements methods.

  9. Pengaruh Konsentrasi Xanthan Gum Dan Konsentrasi Natrium Benzoat Terhadap Mutu Sirup Sirsak

    OpenAIRE

    Capah, Maranata J

    2010-01-01

    The aim of this research was to analize the effect of xanthan gum and sodium benzoate concentration on the quality of sour sop syrup. The research had been performed using factorial completely randomized design with two factors i.e; xanthan gum concentration (L): 0,10 %, 0,15 %, 0,20 %, and 0,25 %; and sodium benzoate concentration (N): 0,050 %, 0,075 %, 0,10 %, and 0,125 %. Parameters analyzed were vitamin C content, total acid content, TSS content, viscosity, organoleptic values (smell and ...

  10. Tooling Converts Stock Bearings To Custom Bearings

    Science.gov (United States)

    Fleenor, E. N., Jr.

    1983-01-01

    Technique for reworking stock bearings saves time and produces helicopter-rotor bearings ground more precisely. Split tapered ring at one end of threaded bolt expands to hold inside of inner race bearing assembly; nut, at other end of bolt, adjusts amount of spring tension. Piece of hardware grasps bearing firmly without interfering with grinding operation. Operation produces bearing of higher quality than commercially available bearings.

  11. Effects of sodium benzoate on storage stability of previously improved beverage from tamarind (Tamarindus indica L.).

    Science.gov (United States)

    Adeola, Abiodun A; Aworh, Ogugua C

    2014-01-01

    The effect of sodium benzoate on the quality attributes of improved tamarind beverage during storage was investigated. Tamarind beverages were produced according to a previously reported improved method, with or without chemical preservatives (100 mg/100 mL sodium benzoate). Tamarind beverage produced according to traditional processing method served as the control. The tamarind beverages were stored for 4 months at room (29 ± 2°C) and refrigerated (4-10°C) temperatures. Samples were analyzed, at regular intervals, for chemical, sensory, and microbiological qualities. Appearance of coliforms or overall acceptability score of 5.9 was used as deterioration index. The control beverages deteriorated by 2nd and 10th days at room and refrigerated temperatures, respectively. Improved tamarind beverage produced without the inclusion of sodium benzoate was stable for 3 and 5 weeks at room and refrigerated temperatures, respectively. Sodium benzoate extended the shelf life of the improved tamarind beverage to 6 and 13 weeks, respectively, at room and refrigerated temperatures.

  12. 76 FR 12873 - Potassium Benzoate; Exemption From the Requirement of a Tolerance

    Science.gov (United States)

    2011-03-09

    ... ingredient (preservative) in pesticide formulations applied to animals (used for food). Landis International..., including infants and children. Potassium benzoate is an approved food preservative, similar in structure... 180.910 when used as an inert ingredient (preservative) in pesticide formulations applied to...

  13. An Overview on the Effects of Sodium Benzoate as a Preservative in Food Products

    Directory of Open Access Journals (Sweden)

    Shahmohammadi

    2016-05-01

    Full Text Available Context Food spoilage has been a common problem throughout history, and much of the spoilage is caused the activity of microorganisms or enzymatic reactions during the storage of food. Thus, using chemical substances could prevent or delay food spoilage and this has led to the great success of these compounds in the treatment of human diseases. Sodium benzoate is one of the synthetic additives that are widely used in the food industry. Evidence Acquisition In this review we summarized the history and role of benzoate sodium in the food industry, its limited value in different food, other uses, pharmacokinetics, and its toxicity in animal studies. A literature search was carried out using MEDLINE, Scopus, Science Direct, and Scientific Information Databases (SID. Results Sodium benzoate is used in different industries as well as the food industry and it has adverse effects similar to other food additives. Conclusions Studies on natural ingredients in foods to find compounds with similar effects as benzoate with less adverse effects is necessary.

  14. Toxic effects of pollutants on the Mineralization of 4-chlorophenol and Benzoate in methanogenic river sediment

    NARCIS (Netherlands)

    van Beelen P; van Vlaardingen PLA

    1993-01-01

    The toxic effects of pollutants on the mineralization of 2 mug/l [U-14C] 4-chlorophenol and benzoate were studied in microcosms with methanogenic sediment from the Rhine river. In contrast with studies using a high substrate concentration no lag time was observed and the half-lives for 4-chlorophen

  15. Identification of a Transcriptional Repressor Involved in Benzoate Metabolism in Geobacter bemidjiensis ▿

    OpenAIRE

    Ueki, Toshiyuki

    2011-01-01

    Subsurface environments contaminated with aromatic compounds can be remediated in situ by Geobacter species. A transcription factor that represses expression of bamA, a benzoate-inducible gene, in Geobacter bemidjiensis during growth with acetate was identified. It is likely that this repressor also regulates other genes involved in aromatic compound metabolism.

  16. Sodium Benzoate and Potassium Sorbate in Processed Meat Products Collected in Ho Chi Minh City, Vietnam

    Directory of Open Access Journals (Sweden)

    Yen T.H. Hoang

    2016-01-01

    Full Text Available Sodium benzoate and potassium sorbates are the two typical preservatives widely used in Vietnam and other countries. The maximum level (ML of sodium benzoate and potassium sorbate in processed meat products imposed by Ministry of Public Health is 1000 ppm. Although there are warnings about overusing of these preservatives that related to human health, many manufacturers do not follow the regulations. The aim of this study was to survey and consider the amounts and presence of these preservatives in processed meat products by using High-performance liquid chromatography (HPLC method. 90 samples of brands and no brands including Vietnamese pork rolls, pâtés, hams, sausages, and fermented pork rolls that available at markets in Ho Chi Minh City were analysed for these two preservatives. There was a preference for using sodium benzoate in all samples. Moreover, Vietnamese pork roll samples had the highest percentage of samples with preservatives concentrations exceeding the ML. Among 90 samples, sodium benzoate was detected in 52.2% of samples and 17.8% of them exceeded the ML, while potassium sorbate was found in 24.4% of samples and only 2.2% of them exceeded the regulated amount. 46.4% of Vietnamese pork rolls, 12.5% of pâtés, and 9.1% of fermented pork rolls had sodium benzoate exceeded the ML, whilst ham and sausage samples contained the concentrations inside the safety limits. Furthermore, only one sample of Vietnamese pork rolls and one sample of sausages had potassium sorbate concentrations surpassing the ML with the level of 1,717.57 mg/kg and 1,814.00 mg/kg, respectively. Furthermore, branded samples showed a significantly different result in compared with no branded samples. Of branded samples, exceeding sodium benzoate level ML was detected in 10% of samples and none of the samples found surpassing potassium sorbate limit amount. Nevertheless, 27.5% and 5% of unbranded samples had sodium benzoate and potassium sorbate higher than

  17. Effect of sodium benzoate preservative on micronucleus induction, chromosome break, and Ala40Thr superoxide dismutase gene mutation in lymphocytes.

    Science.gov (United States)

    Pongsavee, Malinee

    2015-01-01

    Sodium benzoate is food preservative that inhibits microbial growth. The effects of sodium benzoate preservative on micronucleus induction, chromosome break, and Ala40Thr superoxide dismutase gene mutation in lymphocytes were studied. Sodium benzoate concentrations of 0.5, 1.0, 1.5, and 2.0 mg/mL were treated in lymphocyte cell line for 24 and 48 hrs, respectively. Micronucleus test, standard chromosome culture technique, PCR, and automated sequencing technique were done to detect micronucleus, chromosome break, and gene mutation. The results showed that, at 24- and 48-hour. incubation time, sodium benzoate concentrations of 1.0, 1.5, and 2.0 mg/mL increased micronucleus formation when comparing with the control group (P sodium benzoate concentrations of 2.0 mg/mL increased chromosome break when comparing with the control group (P Sodium benzoate did not cause Ala40Thr (GCG→ACG) in superoxide dismutase gene. Sodium benzoate had the mutagenic and cytotoxic toxicity in lymphocytes caused by micronucleus formation and chromosome break.

  18. Effect of Sodium Benzoate Preservative on Micronucleus Induction, Chromosome Break, and Ala40Thr Superoxide Dismutase Gene Mutation in Lymphocytes

    Directory of Open Access Journals (Sweden)

    Malinee Pongsavee

    2015-01-01

    Full Text Available Sodium benzoate is food preservative that inhibits microbial growth. The effects of sodium benzoate preservative on micronucleus induction, chromosome break, and Ala40Thr superoxide dismutase gene mutation in lymphocytes were studied. Sodium benzoate concentrations of 0.5, 1.0, 1.5, and 2.0 mg/mL were treated in lymphocyte cell line for 24 and 48 hrs, respectively. Micronucleus test, standard chromosome culture technique, PCR, and automated sequencing technique were done to detect micronucleus, chromosome break, and gene mutation. The results showed that, at 24- and 48-hour. incubation time, sodium benzoate concentrations of 1.0, 1.5, and 2.0 mg/mL increased micronucleus formation when comparing with the control group (P<0.05. At 24- and 48-hour. incubation time, sodium benzoate concentrations of 2.0 mg/mL increased chromosome break when comparing with the control group (P<0.05. Sodium benzoate did not cause Ala40Thr (GCG→ACG in superoxide dismutase gene. Sodium benzoate had the mutagenic and cytotoxic toxicity in lymphocytes caused by micronucleus formation and chromosome break.

  19. Investigation of comparative efficacy of eugenol and benzyl benzoate in therapy of sheep mange

    Directory of Open Access Journals (Sweden)

    Jezdimirović Milanka

    2010-01-01

    Full Text Available The acaricide efficacy, tolerance and safety of eugenol (10 and 20 % in the treatment of sarcoptic mange in sheep have been investigated. The results were compared with those corresponding for benzyl benzoate (25 %, which was applied to sheep in the same way. The treatment was applied on sheep three times in one-week intervals. Skin scrapings were sampled seven days after each treatment, as well as twenty-eight days following the third one. The changes on the skin were quantified and the mean recovery response (MRR was calculated. The clinical efficacy was assessed according to the MRR and the number of mites in the samples. Following the first treatment 10%eugenol was not significantly less efficacious in comparison with the higher concentration. Having been applied twice 20% eugenol was significantly more efficacious when compared to the lower concentration, which remained the same seven and twenty-eight days after the third application. The efficacy of 10% eugenol in the therapy of mange was significantly higher in comparison with benzyl benzoate following one, two or three administrations. The efficacy of benzyl benzoate four weeks after the third treatment was still significantly lower in comparison with 10% eugenol. The efficacy of 20% eugenol was significantly higher in comparison with its lower concentration as well as that of benzyl benzoate, following the second, and seven and twenty-eight days after the third one. No signs of local or systemic intolerance were observed in sheep treated with either 10 or 20% eugenol, or 25 % benzyl benzoate. .

  20. THERMAL DECOMPOSITION MECHANISM OF BARIUM BENZOATE%苯甲酸钡的热分解机理

    Institute of Scientific and Technical Information of China (English)

    张克立; 袁继兵; 袁良杰; 孙聚堂

    1999-01-01

    Barium benzoate was synthesized in semi-solid phase reaction. The complex was characterized by elemental analysis, IR, X-ray powder diffraction. It is layered structure, monoclinic system. The mechanism of thermal decomposition for barium benzoate was studied by using TG, DTA, IR and gas chromatography-mass spectrometer. The thermal decompositon of barium benzoate in nitrogen proceeded in one stage: it decomposed to form BaCO3 and organic compounds. The organic compounds obtained from decomposition reaction are mainly benzophenone, triphenylmethane and so on.

  1. Microsynthesis of a novel herbicide, propyl 4-[2-[(4,6-dimethoxy-2-pyrimidinyl)oxy] benzylamino] benzoate

    International Nuclear Information System (INIS)

    ZJ273, propyl 4-[2-[(4,6-dimethoxy-2-pyrimidinyl)oxy] benzylamino] benzoate, is a novel herbicide. The microsynthetic method of the compound was developed from 4,6-dimethoxy-2-pyrimidine, propyl (4-benzylamino) benzoate and phenol, and then purified by preparative-HPLC. The yield of end product was 53%. Its chemical structure was characterized by means of 1H-NMR, MS, UV, and its chemical purity was determined to be exceed 98% by HPLC. The microsynthetic method of propyl 4-[2-[(4,6-dimethoxy-2-pyrimidinyl)oxy] benzylamino] benzoate developed sets up a basis to synthesize the radioisotopic labeled target compound. (authors)

  2. Investigation on the adsorption characteristics of sodium benzoate and taurine on gold nanoparticle film by ATR-FTIR spectroscopy

    Science.gov (United States)

    Kumar, Naveen; Thomas, S.; Tokas, R. B.; Kshirsagar, R. J.

    2014-01-01

    Fourier transform infrared (FTIR) spectroscopic studies of sodium benzoate and taurine adsorbed on gold nanoparticle (AuNp) film on silanised glass slides have been studied by attenuated total reflection technique (ATR). The surface morphology of the AuNp films has been measured by Atomic Force Microscopy. The ATR spectra of sodium benzoate and taurine deposited on AuNp film are compared with ATR spectra of their powdered bulk samples. A new red-shifted band appeared along with the symmetric and asymmetric stretches of carboxylate group of sodium benzoate leading to a broadening of the above peaks. Similar behavior is also seen in the case of symmetric and asymmetric stretches of sulphonate group of taurine. The results indicate presence of both chemisorbed and physisorbed layers of both sodium benzoate and taurine on the AuNp film with bottom layer chemically bound to AuNp through carboxylate and sulphonate groups respectively.

  3. Identification of anthranilate and benzoate metabolic operons of Pseudomonas fluorescens and functional characterization of their promoter regions

    Directory of Open Access Journals (Sweden)

    Lee Vincent D

    2006-01-01

    Full Text Available Abstract Background In an effort to identify alternate recombinant gene expression systems in Pseudomonas fluorescens, we identified genes encoding two native metabolic pathways that were inducible with inexpensive compounds: the anthranilate operon (antABC and the benzoate operon (benABCD. Results The antABC and benABCD operons were identified by homology to the Acinetobacter sp. anthranilate operon and Pseudomonas putida benzoate operon, and were confirmed to be regulated by anthranilate or benzoate, respectively. Fusions of the putative promoter regions to the E. coli lacZ gene were constructed to confirm inducible gene expression. Each operon was found to be controlled by an AraC family transcriptional activator, located immediately upstream of the first structural gene in each respective operon (antR or benR. Conclusion We have found the anthranilate and benzoate promoters to be useful for tightly controlling recombinant gene expression at both small (

  4. Synthesis and Anti-Juvenile Hormone Activity of Alkyl 4-(2-Phenoxyalkyloxy) benzoates and Related Compounds

    OpenAIRE

    Furuta, Kenjiro; Shirahashi, Hiromitsu; Ashibe, Kiyo; Yamashita, Haruma; Nishikawa,Masashi; Fujita, Norihiro; Yamada, Naotaka; Kuwano, Eiichi

    2006-01-01

    A number of alkyl 4-(2-phenoxyhexyloxy)benzoates and related compounds were synthesized and evaluated their activity to induce precocious metamorphosis in larvae of the silkworm, which was clearly recognized as a juvenile hormone-deficiency symptom. In the alkyl 4-(2-phenoxyhexyloxy)benzoate series, only the methyl and ethyl esters showed precocious metamorphosis-inducing activity. Replacement of the ester group with an ethylcarbamoyl, butanoyl, nitro or a phenoxy group dramatically decreased...

  5. Development and evaluation of tamarind seed xyloglucan-based mucoadhesive buccal films of rizatriptan benzoate.

    Science.gov (United States)

    Avachat, Amelia M; Gujar, Kishore N; Wagh, Kishor V

    2013-01-16

    Mucoadhesive buccal films were developed using tamarind seed xyloglucan (TSX) as novel mucoadhesive polysaccharide polymer for systemic delivery of rizatriptan benzoate through buccal route. Formulations were prepared based on 3(2) factorial design with concentrations of TSX and carbopol 934P (CP) as independent variables. Three dependent variables considered were tensile strength, bioadhesion force and drug release. DSC analysis revealed no interaction between drug and polymers. Ex vivo diffusion studies were carried out using Franz diffusion cell, while bioadhesive properties were evaluated using texture analyzer with porcine buccal mucosa as model tissue. Results revealed that bilayer film containing 4% (w/v) TSX and 0.5% (w/v) CP in the drug layer and 1% (w/v) ethyl cellulose in backing layer demonstrated diffusion of 93.45% through the porcine buccal mucosa. Thus, this study suggests that tamarind seed polysaccharide can act as a potential mucoadhesive polymer for buccal delivery of a highly soluble drug like rizatriptan benzoate.

  6. Growth and studies of cyclohexylammonium 4-methoxy benzoate single crystal for nonlinear optical applications

    Energy Technology Data Exchange (ETDEWEB)

    Sathya, P.; Gopalakrishnan, R., E-mail: krgkrishnan@annauniv.edu [Crystal Research Lab, Department of Physics, Anna University, Chennai-600002 (India)

    2015-06-24

    Cyclohexylammonium 4-Methoxy Benzoate (C4MB) was synthesised and the functional groups were confirmed by FTIR analysis. The purified C4MB (by repeated recrystallisation) was used for single crystal growth. Single crystal of cyclohexylammonium 4-methoxy benzoate was successfully grown by slow evaporation solution growth method at ambient temperature. Structural orientations were determined from single crystal X-ray diffractometer. Optical absorption and cut off wavelength were identified by UV-Visible spectroscopy. Thermal stability of the crystal was studied from thermogravimetric and differential thermal analyses curves. Mechanical stability of the grown crystal was analysed by Vicker’s microhardness tester. The Second Harmonic Generation (SHG) study revealed that the C4MB compound exhibits the SHG efficiency 3.3 times greater than KDP crystal.

  7. Ultrasonic Investigations of Molecular Interaction in Binary Mixtures of Benzyl Benzoate with Acetonitrile and Benzonitrile

    OpenAIRE

    N. Jaya Madhuri; Naidu, P S; Glory, J.; K. Ravindra Prasad

    2011-01-01

    Ultrasonic velocity, density and viscosity have been measured in the binary mixtures of benzyl benzoate with acetonitrile, benzonitrile at three temperatures 30, 40 and 50 °C. From the experimental data, thermodynamic parameters like adiabatic compressibility, internal pressure, enthalpy, activation energy etc., were computed and the molecular interactions were predicted based on the variation of excess parameters in the mixture. Also theoretical evaluation of velocities was made employing th...

  8. Passive magnetic bearing configurations

    Science.gov (United States)

    Post, Richard F.

    2011-01-25

    A journal bearing provides vertical and radial stability to a rotor of a passive magnetic bearing system when the rotor is not rotating and when it is rotating. In the passive magnetic bearing system, the rotor has a vertical axis of rotation. Without the journal bearing, the rotor is vertically and radially unstable when stationary, and is vertically stable and radially unstable when rotating.

  9. Maintenance Free Bearings

    OpenAIRE

    S. M. Muzakkir & Harish Hirani

    2015-01-01

    In the present research work the need of a Maintenance Free Bearings (MFB) is established. The paper presents preliminary friction calculations to highlight the ways to achieve maintenance free bearings. The existing technologies of well established maintenance free bearings are described. The hybridization of bearing technologies to achieve low cost maintenance free bearings has been exemplified. Finally a combination of passive magnetic repulsion and hydrodynamics ha...

  10. Investigation of comparative efficacy of eugenol and benzyl benzoate in therapy of sheep mange

    OpenAIRE

    Jezdimirović Milanka; Aleksić Nevenka; Radojičić Biljana

    2010-01-01

    The acaricide efficacy, tolerance and safety of eugenol (10 and 20 %) in the treatment of sarcoptic mange in sheep have been investigated. The results were compared with those corresponding for benzyl benzoate (25 %), which was applied to sheep in the same way. The treatment was applied on sheep three times in one-week intervals. Skin scrapings were sampled seven days after each treatment, as well as twenty-eight days following the third one. The changes on the skin were quantified and the me...

  11. The Electrical Properties for Phenolic Isocyanate-Modified Bisphenol-Based Epoxy Resins Comprising Benzoate Group.

    Science.gov (United States)

    Lee, Eun Yong; Chae, Il Seok; Park, Dongkyung; Suh, Hongsuk; Kang, Sang Wook

    2016-03-01

    Epoxy resin has been required to have a low dielectric constant (D(k)), low dissipation factor (Df), low coefficient of thermal expansion (CTE), low water absorption, high mechanical, and high adhesion properties for various applications. A series of novel phenolic isocyanate-modified bisphenol-based epoxy resins comprising benzoate group were prepared for practical electronic packaging applications. The developed epoxy resins showed highly reduced dielectric constants (D(k)-3.00 at 1 GHz) and low dissipation values (Df-0.014 at 1 GHz) as well as enhanced thermal properties.

  12. The Electrical Properties for Phenolic Isocyanate-Modified Bisphenol-Based Epoxy Resins Comprising Benzoate Group.

    Science.gov (United States)

    Lee, Eun Yong; Chae, Il Seok; Park, Dongkyung; Suh, Hongsuk; Kang, Sang Wook

    2016-03-01

    Epoxy resin has been required to have a low dielectric constant (D(k)), low dissipation factor (Df), low coefficient of thermal expansion (CTE), low water absorption, high mechanical, and high adhesion properties for various applications. A series of novel phenolic isocyanate-modified bisphenol-based epoxy resins comprising benzoate group were prepared for practical electronic packaging applications. The developed epoxy resins showed highly reduced dielectric constants (D(k)-3.00 at 1 GHz) and low dissipation values (Df-0.014 at 1 GHz) as well as enhanced thermal properties. PMID:27455751

  13. STUDY ON THE THERMODYNAMIC PROPERTIES OF ADSORPTION OF ETHYL BENZOATE AND DIETHYL PHTHALATE BY PHENOLIC RESIN ADSORBENTS

    Institute of Scientific and Technical Information of China (English)

    Zhong Wang; Zuo-qing Shi; Rong-fu Shi; Yun-ge Fan; Yi-zhong Yang

    2004-01-01

    This paper presents experimental observations on the adsorption of individual solutes by a simple thermodynamic framework, and the equilibrium adsorption of ethyl benzoate and diethyl phthalate on phenolic resin adsorbent in hexane solutions within the temperature range of 293-313 K. The experimental results show that the Freundlich adsorption law is applicable to the adsorption of ethyl benzoate and diethyl phthalate on the adsorbent, since all the correlative factors R' are larger than 0.99. The negative values of all the isosteric adsorption enthalpies for ethyl benzoate and diethyl phthalate indicate that they undergo exothermic processes, while their magnitudes (19-28 kJ/mol) manifest a hydrogen bonding sorption process. Other thermodynamic properties: the free energy changes and the entropy change associated with the adsorption have been calculated from the Gibbs adsorption equation and the Gibbs-Helmholtz equation.

  14. PH-stat fed-batch process to enhance the production of cis, cis-muconate from benzoate by Pseudomonas putida KT2440-JD1

    NARCIS (Netherlands)

    Duuren, J.B.J.H. van; Wijte, D.; Karge, B.; Martins dos Santos, V.A.; Yang, Y.; Mars, A.E.; Eggink, G.

    2012-01-01

    Pseudomonas putida KT2440-JD1 is able to cometabolize benzoate to cis, cis-muconate in the presence of glucose as growth substrate. P. putida KT2440-JD1 was unable to grow in the presence of concentrations above 50 mM benzoate or 600 mM cis, cis-muconate. The inhibitory effects of both compounds wer

  15. Generation of a catR deficient mutant of P. putida KT2440 that produces cis, cis-muconate from benzoate at high rate and yield

    NARCIS (Netherlands)

    Duuren, J.B.J.H. van; Wijte, D.; Leprince, A.; Karge, B.; Puchalka, J.; Wery, J.; Dos Santos, V.A.P.M.; Eggink, G.; Mars, A.E.

    2011-01-01

    Pseudomonas putida KT2440-JD1 was derived from P. putida KT2440 after N-methyl-N'-nitro-N-nitrosoguanidine (NTG)-mutagenesis and exposure to 3-fluorobenzoate (3-FB). The mutant was no longer able to grow using benzoate as a sole carbon source, but co-metabolized benzoate to cis, cis-muconate during

  16. Methyl 4-hydroxy-3-(3'-methyl-2'-butenyl)benzoate, major insecticidal principle from Piper guanacastensis.

    Science.gov (United States)

    Pereda-Miranda, R; Bernard, C B; Durst, T; Arnason, J T; Sánchez-Vindas, P; Poveda, L; San Román, L

    1997-03-01

    The CHCl3-soluble extract of Piper guanacastensis (Piperaceae) was found to have noteworthy insecticidal activity to Aedes atropalpus mosquito larvae (LC50 80.5 micrograms/mL). Bioassay-guided fractionation afforded methyl 4-hydroxy-3-(3'-methyl-2'-butenyl)benzoate (1) as the major bioactive constituent (LC50 20.5 micrograms/mL). The separation of compound 1 from its transesterification artifact (2), ethyl 4-hydroxy-3-(3'-methyl-2'-butenyl)benzoate, was achieved by recycling reversed-phase HPLC. The flavonoids acacetin, chrysin, and pinostrobin were also isolated from the active fraction but did not display insecticidal properties. PMID:9090871

  17. Thermodynamic and Acoustic Study on Molecular Interactions in Certain Binary Liquid Systems Involving Ethyl Benzoate

    Directory of Open Access Journals (Sweden)

    B. Nagarjun

    2013-01-01

    Full Text Available Speeds of sound and density for binary mixtures of ethyl benzoate (EB with N,N-dimethylformamide (NNDMF, N,N-dimethyl acetamide (NNDMAc, and N,N-dimethylaniline (NNDMA were measured as a function of mole fraction at temperatures 303.15, 308.15 K, 313.15 K, and 318.15 K and atmospheric pressure. From the experimental data, adiabatic compressibility (βad, intermolecular free length (Lf, and molar volume (V have been computed. The excess values of the above parameters were also evaluated and discussed in light of molecular interactions. Deviation in adiabatic compressibilities and excess intermolecular free length (LfE are found to be negative over the molefraction of ethyl benzoate indicating the presence of strong interactions between the molecules. The negative excess molar volume VE values are attributed to strong dipole-dipole interactions between unlike molecules in the mixtures. The binary data of Δβad, VE, and LfE were correlated as a function of molefraction by using the Redlich-Kister equation.

  18. Simultaneous Determination of Potassium Sorbate and Sodium Benzoate in Doogh Using High Performance Liquid Chromatography

    Directory of Open Access Journals (Sweden)

    S. Sohrabvandi

    2015-09-01

    Full Text Available In this research, high performance liquid chromatography (HPLC as a simple and rapid technique was used for the determination of potassium sorbate and sodium benzoate in different brands of Doogh (typical Iranian drink based on fermented milk. The chromatographic separation was achieved with a C18 column (250 mm×4 I.D, 5 µm and one buffered mobile phase, acetate buffer (0.2 mol/L, pH4.4: acetonitrile (63:37 at a flow rate of 1 mL/min. The effluent was monitored at 235nm, respectively. The main affecting factors, such as Carrez solution amount, pH and centrifuge speed were optimized. Limits of detection (LODs were 1.823 for sorbic acid and 1.985 for benzoic acid. Relative standard deviations (RSDs for quintuplicate analyses were 4.4 for sorbic acid and 4.087 for benzoic acid. The method also showed good linearity in a range from 4 to 1000 mg/L with correlation coefficients (R2 of 0.990 for sorbic acid and 0.995 for benzoic acid. Recoveries for the two analytes were 80 for sorbic acid and 65 for benzoic acid. Comparing to the other techniques, the proposed method was significantly less time-consuming and had more acceptable accuracy, precision and interruption elimination in samples. The developed method was successfully used for the routine monitoring of benzoate and sorbate in Doogh.

  19. Formulation and evaluation of fast dissolving sublingual films of Rizatriptan Benzoate

    Directory of Open Access Journals (Sweden)

    Bhyan Bhupinder

    2012-03-01

    Full Text Available Rizatriptan Benzoate, a serotonin 5-HT1 receptor agonist is a new generation antimigraine drug which has oral bioavailability of 47% due to hepatic first pass metabolism. The present study investigated the possibility of developing Rizatriptan benzoate fast dissolving sublingual films allowing fast, reproducible drug dissolution in the oral cavity, thus bypassing first pass metabolism to provide rapid onset of action of the drug. The fast dissolving films were prepared by solvent casting method. Low viscosity grade of hydroxylpropyl methylcellulose (HPMC E 15 and maltodextrin were used in combination as film forming polymer, due to their hydrophilic nature and palatable taste. To decrease the disintegration time of formulations sodium starch glycolate was used as disintegrating agent. Glycerol, mannitol, aspartame and sodium lauryl sulphate were used as a cooling agent, sweetening agent and oral penetration enhancer respectively. All the films formulations (F1-F8 was evaluated for their thickness, weight variations, tensile strength, percentage elongation, folding endurance, surface pH, in-vitro disintegration, drug content, in-vitro drug release and ex-vivo permeation. Disintegration time showed by the formulations was found to be in range of 25-50 sec. Formulations F1 and F2 showed 90% in-vitro drug release within 7 min and 61% ex-vivo drug permeation within16 min. The film showed an excellent stability at least for 4 weeks when stored at 400 C and 75% in humidity.

  20. Development and preventative effect against pine wilt disease of a novel liquid formulation of emamectin benzoate.

    Science.gov (United States)

    Takai, Kazuya; Suzuki, Toshio; Kawazu, Kazuyoshi

    2003-03-01

    Injection of the poorly water-soluble emamectin benzoate (EB) into pine trunks required the development of an efficient liquid formulation. For injection into big trees in forests a good rate of injection and a high active content were required. Tests on the viscosity and EB-solubilizing ability of 14 various solubilizers in diethylene glycol monobutyl ether (DGMBE) led to the selection of Sorpol SM-100PM as the solubilizer of the formulation. Relationships between the solubilizing ability and amounts of Sorpol SM-100PM and DGMBE relative to that of EB, and between the concentration of the latter and the viscosity or the injection rate of the formulation led to a novel 40 g litre(-1) emamectin benzoate formulation (Shot Wan Liquid Formulation), which was composed of EB (40), Sorpol SM-100PM (120), DGMBE (160) and distilled water (50 g litre(-1)) in methanol. Injection of this formulation at a dose of 10 g EB per unit volume of pine tree prevented over 90% of the trees from wilting caused by pine wood nematode, and this preventative effect continued for 3 years. Neither discolouration of the leaves nor injury around the injection hole on the trees was observed after injection of the formulation.

  1. Secondary. cap alpha. -deuterium kinetic isotope effects in solvolyses of ferrocenylmethyl acetate and benzoate in ethanol

    Energy Technology Data Exchange (ETDEWEB)

    Sutic, D. (Univ. of Zagreb, Yugoslavia); Asperger, S.; Borcic, S.

    1982-12-17

    Secondary ..cap alpha..-deuterium kinetic isotope effects (KIE) in solvolyses of ferrocenyldideuteriomethyl acetate and benzoate were determined in 96% (v/v) ethanol, at 25/sup 0/C, as k/sub H//k/sub D/ = 1.24 and 1.26, respectively. The KIEs were also determined in the presence of 0.1 mol dm/sup -3/ lithium perchlorate: the k/sub H//k/ sub D/ values were 1.23 and 1.22 for acetate and benzoate complexes, respectively. The maximum KIE for the C-O bond cleavage of a primary substrate is as large as, or larger than, that of secondary derivatives, which is estimated to be 1.23 per deuterium. The measured KIE of about 12% per D therefore represents a strongly reduced effect relative to its maximum. The solvolyses exhibit ''a special salt effect''. This effect indicates the presence of solvent-separated ion pairs and the return to tight pairs. As the maximum KIE is expected in solvolyses involving transformation of one type of ion pair into another, the strongly reduced ..cap alpha..-D KIE supports the structure involving direct participation of electrons that in the ground state are localized at the iron atom. The alkyl-oxygen cleavage is accompanied by 10-15% acyl-oxygen cleavage.

  2. Axial Halbach Magnetic Bearings

    Science.gov (United States)

    Eichenberg, Dennis J.; Gallo, Christopher A.; Thompson, William K.

    2008-01-01

    Axial Halbach magnetic bearings have been investigated as part of an effort to develop increasingly reliable noncontact bearings for future high-speed rotary machines that may be used in such applications as aircraft, industrial, and land-vehicle power systems and in some medical and scientific instrumentation systems. Axial Halbach magnetic bearings are passive in the sense that unlike most other magnetic bearings that have been developed in recent years, they effect stable magnetic levitation without need for complex active control.

  3. Teddy Bear Stories

    DEFF Research Database (Denmark)

    van Leeuwen, Theo; Caldas-Coulthardt, Carmen

    2014-01-01

    This paper presents a semiotic analysis of a key cultural artefact, the teddy bear. After introducing the iconography of the teddy bear, it analyses different kinds of stories to show how teddy bears are endowed with meaning in everyday life: stories from children's books, reminiscenses by adults...

  4. Cryogenic Hybrid Magnetic Bearing

    Science.gov (United States)

    Meeks, Crawford R.; Dirusso, Eliseo; Brown, Gerald V.

    1994-01-01

    Cryogenic hybrid magnetic bearing is example of class of magnetic bearings in which permanent magnets and electromagnets used to suspend shafts. Electromagnets provide active control of position of shaft. Bearing operates at temperatures from -320 degrees F (-196 degrees C) to 650 degrees F (343 degrees C); designed for possible use in rocket-engine turbopumps, where effects of cryogenic environment and fluid severely limit lubrication of conventional ball bearings. This and similar bearings also suitable for terrestrial rotating machinery; for example, gas-turbine engines, high-vacuum pumps, canned pumps, precise gimbals that suspend sensors, and pumps that handle corrosive or gritty fluids.

  5. Crystal structure of catena-diaquabis (μ-3,5-diamino benzoate O,O') (3,5-diamino benzoate O,O) yttrium(III) tetrahydrate

    International Nuclear Information System (INIS)

    The compounds has been the formula [Y(C7H7N2O2)3 x 2H2O] x 4H2O and crystallizes in the triclinic space group P1 with a = 9.825(3), b 12.440(3), c = 11.937 A, α = 101.56(3), β = 104.18(3), γ 101.24(3)o and Z = 2. The structure was solved by the heavy-atom method and refined to the final R value of 0.036 for 4431 observed reflections. The structure of the complex consists of the yttrium(III) cations connected by two bidentate bridging carboxylate groups of 3,5-diamino benzoate ligands. This form becomes a centrosymmetric linear polymeric compounds in this way. This distances Y-Yi and Y-Yii are 4.945(2) and 4.950(2) A, respectively. The coordination polyhedron around the yttrium(III) ion can be described as a distorted dodecahedron. The Y-O distances range from 2.252(2)-2.473(2) A depending on the mode of carboxylate group coordination. (author). 22 refs, 3 figs, 4 tabs

  6. Elimination kinetic of 17B-estradiol 3-benzoate and 17B-nandrolone laureate ester metabolites in calves' urine

    NARCIS (Netherlands)

    Pinel, G.; Rambaud, L.; Cacciatore, G.; Bergwerff, A.; Elliott, C.; Nielen, M.W.F.

    2008-01-01

    Efficient control of the illegal use of anabolic steroids must both take into account metabolic patterns and associated kinetics of elimination; in this context, an extensive animal experiment involving 24 calves and consisting of three administrations of 17 beta-estradiol 3-benzoate and 17 beta-nan

  7. Pyrazole Supported Zinc(II Benzoates as Catalysts for the Ring Opening Copolymerization of Cyclohexene Oxide and Carbon Dioxide

    Directory of Open Access Journals (Sweden)

    Mapudumo L. Lephoto

    2016-01-01

    Full Text Available The bis(pyrazolezinc(II benzoate complexes bis(3,5-diphenylpyrazolezinc(II benzoate (1, bis(3,5-diphenylpyrazolezinc(II 3,5-dinitrobenzoate (2, bis(3,5-diphenylpyrazolezinc(II 4-hydroxybenzoate (3, and bis(3,5-di-tert-butylpyrazolezinc(II 2-chlorobenzoate (4 were synthesized from the reaction of 3,5-diphenylpyrazole (L1 or 3,5-di-tert-butylpyrazole (L2, zinc(II acetate and the appropriate benzene carboxylic acid. The molecular structure of complex 2 confirmed that these zinc(II benzoate complexes adopt a 4-coordinate tetrahedral geometry. All four complexes were screened as catalysts for the copolymerization of carbon dioxide (CO2 and cyclohexene oxide (CHO and were found to be active for the formation of poly(cyclohexene carbonate (PCHC at CO2 pressures as low as 1.0 MPa under solvent-free conditions and without the use of a co-catalyst. At some reaction condition, most of the catalysts produced PCHC with high carbonate content of up to 98% and a good amount of cyclic cyclohexene carbonate (CCHC. The copolymers produced have low to moderate molecular weights (5200–12300 g/mol and with polydispersity indices that vary from 1.19 to 2.50. Matrix Assisted Laser Desorption/Ionization-Time of Flight Mass Spectra (MALDI-TOF MS of these copolymers showed they have benzoate and hydroxyl end groups.

  8. Food preservatives sodium benzoate and propionic acid and colorant curcumin suppress Th1-type immune response in vitro.

    Science.gov (United States)

    Maier, Elisabeth; Kurz, Katharina; Jenny, Marcel; Schennach, Harald; Ueberall, Florian; Fuchs, Dietmar

    2010-07-01

    Food preservatives sodium benzoate and propionic acid and colorant curcumin are demonstrated to suppress in a dose-dependent manner Th1-type immune response in human peripheral blood mononuclear cells (PBMC) in vitro. Results show an anti-inflammatory property of compounds which however could shift the Th1-Th2-type immune balance towards Th2-type immunity.

  9. Effect of emamectin benzoate on mortality, proboscis extension, gustation and reproduction of the corn earworm, Helicoverpa zea.

    Science.gov (United States)

    López, Juan D; Latheef, M A; Hoffmann, W C

    2010-01-01

    Newly emerged corn earworm adults, Helicoverpa zea (Boddie) (Lepidoptera: Noctuidae) require a carbohydrate source from plant or other exudates and nectars for dispersal and reproduction. Adults actively seek and forage at feeding sites upon eclosion in the habitat of the larval host plant or during dispersal to, or colonization of, a suitable reproductive habitat. This nocturnal behavior of H. zea has potential for exploitation as a pest management strategy for suppression using an adult feeding approach. This approach entails the use of a feeding attractant and stimulant in combination with a toxicant that when ingested by the adult will either reduce fecundity/fertility at sub-lethal dosages or kill the adult. The intent of this study was to assess reproductive inhibition and toxicity of emamectin benzoate on H. zea when ingested by the adults when mixed in ppm active ingredient (wt:vol) with 2.5 M sucrose as a feeding stimulant. Because the mixture has to be ingested to function, the effect of emamectin benzoate was also evaluated at sub-lethal and lethal concentrations on proboscis extension and gustatory response of H. zea in the laboratory. Feral males captured in sex pheromone-baited traps in the field were used for toxicity evaluations because they were readily available and were more representative of the field populations than laboratory-reared adults. Laboratory-reared female moths were used for reproduction effects because it is very difficult to collect newly emerged feral females from the field. Emamectin benzoate was highly toxic to feral H. zea males with LC(50) values (95% CL) being 0.718 (0.532-0.878), 0.525 (0.316-0.751), and 0.182 (0.06-0.294) ppm for 24, 48 and 72 h responses, respectively. Sub-lethal concentrations of emamectin benzoate did not significantly reduce proboscis extension response of feral males and gustatory response of female H. zea. Sublethal concentrations of emamectin benzoate significantly reduced percent larval hatch of

  10. Scientific Opinion on the safety and efficacy of sodium benzoate as a silage additive for pigs, poultry, bovines, ovines, goats, rabbits and horses

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Additives and Products or Substances used in Animal Feed

    2012-07-01

    Full Text Available

    Sodium benzoate is intended for use as a technological additive to improve the ensiling process at a proposed dose of 2 400 mg/kg fresh matter, the eventual use of the silage being for pigs, poultry, bovines, ovines, goats, rabbits and horses. The application of sodium benzoate in the preparation of silage at the proposed dose was safe for the target animals. The proposed maximum dose of sodium benzoate is estimated to result in a comparable consumer exposure as does its use as preservative in other feedingstuffs and to make a minimal contribution to consumer exposure. The FEEDAP Panel concluded that sodium benzoate when used as a silage additive is safe for the consumer. Sodium benzoate is not considered as a skin irritant but may be mildly irritant to the eyes. As no data on sensitisation appear to be available, the FEEDAP Panel considered it prudent to treat sodium benzoate as a potential sensitiser. In the absence of information on particle size and dusting potential, a risk from inhalation cannot be excluded. The FEEDAP Panel concluded that there are no safety concerns for the environment resulting from the use of sodium benzoate as a silage additive. Based on a series of laboratory studies, sodium benzoate at the recommended dose was shown to have the potential to improve the production of silage by reducing pH and increasing the preservation of dry matter. This was demonstrated in a range of easy, moderately difficult and difficult to ensile forage materials. Sodium benzoate at concentrations between 250 and 2 500 mg/kg forage also has the potential to increase the aerobic stability of ensiled materials at a wide range of dry matter content.

  11. Electro-optic and dynamic studies of biphenyl benzoate ferroelectric liquid crystals

    Energy Technology Data Exchange (ETDEWEB)

    Hemine, J., E-mail: hemine1@yahoo.f [Laboratoire de Physique de la Matiere Condensee, Universite Hassan II, Mohammedia-Casablanca, BP 146, F.S.T. Mohammedia (Morocco); Daoudi, A. [Universite Lille Nord de France, F-59000 Lille (France); ULCO, LDSMM, F-59140 Dunkerque (France); CNRS UMR8024, F-59140 Dunkerque (France); Legrand, C. [Universite Lille Nord de France, F-59000 Lille (France); ULCO, LEMCEL, F-62228 Calais (France); El kaaouachi, A.; Nafidi, A. [Laboratoire de Physique de la Matiere Condensee, Faculte des Sciences Ibnou Zohr, BP 28/S 80000 Agadir (Morocco); Ismaili, M.; Isaert, N. [Universite Lille Nord de France, F-59000 Lille (France); USTL, LDSMM, F-59655 Villeneuve d' Ascq (France); CNRS UMR8024, F-59655 Villeneuve d' Ascq (France); Nguyen, H.T. [Centre de Recherche Paul Pascal, Universite de Bordeaux 1, 33600 Pessac (France)

    2010-05-01

    We present electro-optic and dynamic properties on three homologous of biphenyl benzoate series of ferroelectric liquid crystals (FLCs) exhibiting the chiral smectic C phase (SmC*). The three compounds present high spontaneous polarization and show the SmC*-SmA*-N* phase sequence. Dielectric spectroscopy was used to provide the dynamics and dipolar ordering of the ferroelectric phase. The Goldstone relaxation mode was studied for sample cells on planar geometry without a DC bias voltage. The rotational viscosity corresponding to molecular motions in the SmC* phase was determined from dielectric measurements. The Arrhenius-type behavior of the rotational viscosity was found and the corresponding activation energies were evaluated.

  12. Spectroscopic studies on the interaction of sodium benzoate, a food preservative, with calf thymus DNA.

    Science.gov (United States)

    Zhang, Guowen; Ma, Yadi

    2013-11-01

    The interaction between sodium benzoate (SB) and calf thymus DNA in simulated physiological buffer (pH 7.4) using acridine orange (AO) dye as a fluorescence probe, was investigated by UV-Vis absorption, fluorescence and circular dichroism (CD) spectroscopy along with DNA melting studies and viscosity measurements. An expanded UV-Vis spectral data matrix was resolved by multivariate curve resolution-alternating least squares (MCR-ALS) approach. The equilibrium concentration profiles and the pure spectra for SB, DNA and DNA-SB complex from the high overlapping composite response were simultaneously obtained. The results indicated that SB could bind to DNA, and hydrophobic interactions and hydrogen bonds played a vital role in the binding process. Moreover, SB was able to quench the fluorescence of DNA-AO complex through a static procedure. The quenching observed was indicative of an intercalative mode of interaction between SB and DNA, which was supported by melting studies, viscosity measurements and CD analysis.

  13. Optimal Synchronizability of Bearings

    OpenAIRE

    Araújo, N. A. M.; Seybold, H.; Baram, R. M.; Herrmann, H. J.; Andrade, J. S.

    2013-01-01

    Bearings are mechanical dissipative systems that, when perturbed, relax toward a synchronized (bearing) state. Here we find that bearings can be perceived as physical realizations of complex networks of oscillators with asymmetrically weighted couplings. Accordingly, these networks can exhibit optimal synchronization properties through fine tuning of the local interaction strength as a function of node degree [Motter, Zhou, and Kurths, Phys. Rev. E 71, 016116 (2005)]. We show that, in analogy...

  14. Bear Spray Safety Program

    Science.gov (United States)

    Blome, C.D.; Kuzniar, R.L.

    2009-01-01

    A bear spray safety program for the U.S. Geological Survey (USGS) was officially initiated by the Firearms Safety Committee to address accident prevention and to promote personnel training in bear spray and its transportation, storage, and use for defense against wild animals. Used as part of a system including firearms, or used alone for those who choose not to carry a firearm, bear spray is recognized as an effective tool that can prevent injury in a wild animal attack.

  15. Bearing restoration by grinding

    Science.gov (United States)

    Hanau, H.; Parker, R. J.; Zaretsky, E. V.; Chen, S. M.; Bull, H. L.

    1976-01-01

    A joint program was undertaken by the NASA Lewis Research Center and the Army Aviation Systems Command to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. No bearing failures occurred related to the restoration by grinding process. The risk and cost of a bearing restoration by grinding programs was analyzed. A microeconomic impact analysis was performed.

  16. Bearing fatigue investigation 3

    Science.gov (United States)

    Nahm, A. H.; Bamberger, E. N.; Signer, H. R.

    1982-01-01

    The operating characteristics of large diameter rolling-element bearings in the ultra high speed regimes expected in advanced turbine engines for high performance aircraft were investigated. A high temperature lubricant, DuPont Krytox 143 AC, was evaluated at bearing speeds to 3 million DN. Compared to the results of earlier, similar tests using a MIL-L-23699 (Type II) lubricant, bearings lubricated with the high density Krytox fluid showed significantly higher power requirements. Additionally, short bearing lives were observed when this fluid was used with AISI M50 bearings in an air atmosphere. The primary mode of failure was corrosion initiated surface distress (fatigue) on the raceways. The potential of a case-carburized bearing to sustain a combination of high-tangential and hertzian stresses without experiencing race fracture was also investigated. Limited full scale bearing tests of a 120 mm bore ball bearing at a speed of 25,000 rpm (3 million DN) indicated that a carburized material could sustain spalling fatigue without subsequent propagation to fracture. Planned life tests of the carburized material had to be aborted, however, because of apparent processing-induced material defects.

  17. EcoBears

    DEFF Research Database (Denmark)

    Nielsen, Nick; Pedersen, Sandra Bleuenn; Sørensen, Jens Ager;

    2015-01-01

    In this paper, we introduce the EcoBears concept that aims to augment household appliances with functional and aesthetic features to promote their "use'' and "longevity of use'' to prevent their disposal. The EcoBears also aim to support the communication of environmental issues in the home setti...

  18. Arcturus and the Bears

    Science.gov (United States)

    Antonello, E.

    2009-08-01

    Arcturus is the brightest star in Bootes. The ancient Greek name Arktouros means Bear Guard. The star, however, is not close to Ursa Maior (Big She-Bear) and Ursa Minor (Little She-Bear), as the name would suggest. This curious discrepancy could be explained by the star proper motion, assuming the name Bear Guard is a remote cultural heritage. The proper motion analysis could allow us to get an insight also into an ancient myth regarding Ursa Maior. Though we cannot explain scientifically such a myth, some interesting suggestions can be obtained about its possible origin, in the context of the present knowledge of the importance of the cult of the bear both during the Palaeolithic times and for several primitive populations of modern times, as shown by the ethnological studies.

  19. Simultaneous Determination of Sodium Benzoate Potassium Sor­bate and Natamycin Content in Iranian Yoghurt Drink (Doogh and the Associated Risk of Their Intake through Doogh Consumption

    Directory of Open Access Journals (Sweden)

    Zahra Esfandiari

    2013-08-01

    Full Text Available Background: Regarding the public health concerns over the use of food preservatives in yoghurt drink “Doogh", the aim of this study was the determination of sodium benzoate, potassium sorbate and natamycin in Doogh. Based on Iranian national standard, none of these preservatives are permitted to be used in Doogh.Methods: A total of 39 Doogh samples were analyzed through RP- HPLC in order to quantify sodium benzoate, potassium sorbate and natamaycin simultaneously. Exposure to each preservative is estimated by mean and maximum concentrations as the residue levels. The per capita Doogh consumption was calculated by the published data from official reports for Doogh annual production in Iran.Results: All samples were shown to contain sodium benzoate while natamaycin was detected in 10.25% of the samples and potassium sorbate was not detected in any of them. Sodium benzoate concentration extremely varied among the investigated samples ranged from 0.94 to 9.77 mg/l. Due to the result of the exposure estimation, no serious public health concern would exist regarding the mentioned preservatives.Conclusions: The detection of sodium benzoate in all Doogh samples could indicate the natural production of benzoic acid in yoghurt. Sodium benzoate may be formed through the interaction of the added food grade salt to the Doogh formula which contains benzoic acid. The results of exposure estimation show the lack of health risk within the usage of preservatives in spite of the national regulatory agencies does not permit the preservative use.

  20. Changes induced by UV radiation in the presence of sodium benzoate in films formulated with polyvinyl alcohol and carboxymethyl cellulose

    International Nuclear Information System (INIS)

    This work was focused on: i) developing single and blend films based on carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVOH) studying their properties, ii) analyzing the interactions between CMC and PVOH and their modifications UV-induced in the presence of sodium benzoate (SB), and iii) evaluating the antimicrobial capacity of blend films containing SB with and without UV treatment. Once the blend films with SB were exposed to UV radiation, they exhibited lower moisture content as well as a greater elongation at break and rougher surfaces compared to those without treatment. Considering oxygen barrier properties, the low values obtained would allow their application as packaging with selective oxygen permeability. Moreover, the characteristics of the amorphous phase of the matrix prevailed with a rearrangement of the structure of the polymer chain, causing a decrease of the crystallinity degree. These results were supported by X-rays and DSC analysis. FT-IR spectra reflected some degree of polymer–polymer interaction at a molecular level in the amorphous regions. The incorporation of sodium benzoate combined with UV treatment in blend films was positive from the microbial point of view because of the growth inhibition of a wide spectrum of microorganisms. From a physicochemical perspective, the UV treatment of films also changed their morphology rendering them more insoluble in water, turning the functionalized blend films into a potential material to be applied as food packaging. - Highlights: • CMC:PVOH blend films were developed with the addition of sodium benzoate (SB). • Exposition to UV radiation was carried out with sodium benzoate as photoinitiator. • Blend films were exposed to UV radiation to modify their surface morphology. • Low O2 permeability of UV treated blends allow them to be used as selective packaging. • Efficacy of SB as an antimicrobial agent was examined with and without UV radiation

  1. Changes induced by UV radiation in the presence of sodium benzoate in films formulated with polyvinyl alcohol and carboxymethyl cellulose

    Energy Technology Data Exchange (ETDEWEB)

    Villarruel, S. [Faculty of Exact Sciences, UNLP (Argentina); Giannuzzi, L.; Rivero, S. [Center for Research and Development in Food Cryotechnology (CCT-CONICET La Plata), 47 and 116 (Argentina); Pinotti, A., E-mail: acaimpronta@hotmail.com [Center for Research and Development in Food Cryotechnology (CCT-CONICET La Plata), 47 and 116 (Argentina); Faculty of Engineering, UNLP, La Plata 1900 (Argentina)

    2015-11-01

    This work was focused on: i) developing single and blend films based on carboxymethyl cellulose (CMC) and polyvinyl alcohol (PVOH) studying their properties, ii) analyzing the interactions between CMC and PVOH and their modifications UV-induced in the presence of sodium benzoate (SB), and iii) evaluating the antimicrobial capacity of blend films containing SB with and without UV treatment. Once the blend films with SB were exposed to UV radiation, they exhibited lower moisture content as well as a greater elongation at break and rougher surfaces compared to those without treatment. Considering oxygen barrier properties, the low values obtained would allow their application as packaging with selective oxygen permeability. Moreover, the characteristics of the amorphous phase of the matrix prevailed with a rearrangement of the structure of the polymer chain, causing a decrease of the crystallinity degree. These results were supported by X-rays and DSC analysis. FT-IR spectra reflected some degree of polymer–polymer interaction at a molecular level in the amorphous regions. The incorporation of sodium benzoate combined with UV treatment in blend films was positive from the microbial point of view because of the growth inhibition of a wide spectrum of microorganisms. From a physicochemical perspective, the UV treatment of films also changed their morphology rendering them more insoluble in water, turning the functionalized blend films into a potential material to be applied as food packaging. - Highlights: • CMC:PVOH blend films were developed with the addition of sodium benzoate (SB). • Exposition to UV radiation was carried out with sodium benzoate as photoinitiator. • Blend films were exposed to UV radiation to modify their surface morphology. • Low O{sub 2} permeability of UV treated blends allow them to be used as selective packaging. • Efficacy of SB as an antimicrobial agent was examined with and without UV radiation.

  2. Synthesis and anti-inflammatory-analgesic activity of 2',4'-difluoro-3-(carbamoyl)biphenyl-4-yl benzoates

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Eighteen 2',4'-difluoro-3-(carbamoyl)biphenyl-4-yl benzoates were synthesized from diflunisal in three steps with total yields from 72% to 86%. All compounds were identified by IR, 1H NMR, MS and elemental analysis. The anti-inflammatory activity and analgesic activity for 18 compounds were evaluated. The preliminary assay results showed that compounds 4a and 4p exhibited potent anti-inflammatory-analgesic activity.

  3. Efficacy of vinegar, sorbitol and sodium benzoate in mitigation of Salmonella contamination in betel leaf

    Directory of Open Access Journals (Sweden)

    Al Asmaul Husna

    2015-06-01

    Full Text Available The present study was undertaken to mitigate Salmonella from betel leaf in Mymensingh. A total of 35 betel leaf samples were collected from 2 baroujes and 5 local markets in Mymensingh. The samples were sub-divided into two groups: (i phosphate buffer solution (PBS washed, and (ii grinded sample. There was control and treated (with 1.5% vinegar, sorbitol, and sodium benzoate sub-groups in both groups. Mitigation of Salmonella was determined by comparing Total Viable Count (TVC and Total Salmonella Count (TSAC of control with treated groups. No bacterial growth was observed in the betel leaf samples collected directly from barouj level. At market level, when grinded, there was no growth of bacteria in Plate Count Agar (PCA and Salmonella- Shigella (SS or Xylose Lysine De-oxy-chocolate (XLD in both treated and untreated groups. But when the PBS washed samples were used, the TVC (mean log CFU±SD/mL of betel leaf ranged from 5.16±0.82 to 5.96±1.11, whereas the TSAC value ranged from 4.87±0.58 to 5.56±1.00 for untreated group. In vinegar, there was no growth, but when treated with sorbitol, the TVC (mean log CFU±SD/mL value reduced to 5.00±0.54 to 5.66±1.09, and TSAC (mean log CFU±SD/mL value reduced to 4.28±0.71 to 4.78±0.64. When treated with sodium benzoate, the TVC (mean log CFU±SD/mL value reduced to 5.06±0.53 to 5.75±1.02, and TSAC (mean log CFU±SD/mL value reduced to 4.34±0.79 to 4.92±0.64. Data of this study indicates that all the three chemicals were effective in terms of reducing bacterial load but vinegar (1.5% was found to be the most effective against Salmonella as well as some other bacteria when treated for 10 min.

  4. Dietary exposure of children and teenagers to benzoates, sulphites, butylhydroxyanisol (BHA) and butylhydroxytoluen (BHT) in Beirut (Lebanon).

    Science.gov (United States)

    Soubra, L; Sarkis, D; Hilan, C; Verger, Ph

    2007-02-01

    The acceptable daily intake (ADI) for a considered chemical is by definition the amount of that substance which can be ingested every day during the life time without appreciable health risk. The theoretical risk of exceeding the ADI for benzoates, sulphites, butylhydroxyanisol (BHA) and butylhydroxytoluen (BHT) has often been examined on the basis of worst case scenario. The aim of this paper is to assess the actual intake of the food additives listed above for a group of the Lebanese population (students aged between 9 and 18 years old) likely to be highly exposed to food additives through the consumption of processed foods. Dietary exposure was obtained by combining food consumption data with food additives levels determined by chemical analysis. Food products available in Lebanon and containing added benzoates, sulphites, BHA and BHT were identified. Overall 420 samples of foods and beverages were analysed. The determination of food additives residue levels was carried out according to the official methods adopted in "Lebanese Institute for agronomic research" (IRAL) on food as consumed. The acceptable daily intake (ADI) could be exceeded for sulphites and BHT by a fraction of the population, in particular within children of 9-13 years old. Among all food additive-containing foods, the highest contributors were: soft drinks to benzoates intake, nuts and canned juices to sulphites intake, bread and biscuits to BHA intake and chewing gum to BHT intake.

  5. Adsorption of choline benzoate ionic liquid on graphene, silicene, germanene and boron-nitride nanosheets: a DFT perspective.

    Science.gov (United States)

    García, Gregorio; Atilhan, Mert; Aparicio, Santiago

    2015-07-01

    The adsorption of choline benzoate ([CH][BE]) ionic liquid (IL) on the surface of different hexagonal nanosheets has been studied using Density Functional Theory (DFT) methods. For this, the interaction mechanism, binding energies and electronic structure of [CH][BE] ionic liquid on four types of nanosheets, i.e., graphene, silicene, germanene and boron-nitride, were estimated and compared. The adsorption of [CH][BE] ionic liquid on different nanosheets is mainly featured by van der Waals forces, leading to strong benzoate ion-surface π-stacking. Likewise, there is also an important charge transfer from the anion to the sheet. The electronic structure analysis shows that Si- and Ge-based sheets lead to the largest changes in the HOMO and LUMO levels of choline benzoate. This paper provides new insights into the capability of DFT methods to provide useful information about the adsorption of ionic liquids on nanosheets and how ionic liquid features could be tuned through the adsorption on the suitable nanosheet. PMID:26040507

  6. Ultra-precision bearings

    CERN Document Server

    Wardle, F

    2015-01-01

    Ultra-precision bearings can achieve extreme accuracy of rotation, making them ideal for use in numerous applications across a variety of fields, including hard disk drives, roundness measuring machines and optical scanners. Ultraprecision Bearings provides a detailed review of the different types of bearing and their properties, as well as an analysis of the factors that influence motion error, stiffness and damping. Following an introduction to basic principles of motion error, each chapter of the book is then devoted to the basic principles and properties of a specific type of bearin

  7. Biosynthesis and emission of insect-induced methyl salicylate and methyl benzoate from rice

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Nan [University of Tennessee, Knoxville (UTK); Guan, Ju [University of Tennessee, Knoxville (UTK); Ferrer, Jean-Luc [Universite Joseph Fourier, France; Engle, Nancy L [ORNL; Chern, Mawsheng [University of California, Davis; Ronald, Pamela [University of California, Davis; Tschaplinski, Timothy J [ORNL; Chen, Feng [University of Tennessee, Knoxville (UTK)

    2010-01-01

    Two benzenoid esters, methyl salicylate (MeSA) and methyl benzoate (MeBA), were detected from insect-damaged rice plants. By correlating metabolite production with gene expression analysis, five candidate genes encoding putative carboxyl methyltransferases were identified. Enzymatic assays with Escherichia coli-expressed recombinant proteins demonstrated that only one of the five candidates, OsBSMT1, has salicylic acid (SA) methyltransferase (SAMT) and benzoic acid (BA) methyltransferase (BAMT) activities for producing MeSA and MeBA, respectively. Whereas OsBSMT1 is phylogenetically relatively distant from dicot SAMTs, the three-dimensional structure of OsBSMT1, which was determined using homology-based structural modeling, is highly similar to those of characterized SAMTs. Analyses of OsBSMT1 expression in wild-type rice plants under various stress conditions indicate that the jasmonic acid (JA) signaling pathway plays a critical role in regulating the production and emission of MeSA in rice. Further analysis using transgenic rice plants overexpressing NH1, a key component of the SA signaling pathway in rice, suggests that the SA signaling pathway also plays an important role in governing OsBSMT1 expression and emission of its products, probably through a crosstalk with the JA signaling pathway. The role of the volatile products of OsBSMT1, MeSA and MeBA, in rice defense against insect herbivory is discussed.

  8. Spectral Properties and Solubilization Location of 2'-Ethylhexyl 4-(N,N-Dimethylamino)benzoate in Micelles

    Institute of Scientific and Technical Information of China (English)

    Ning Ding; Xin-zhen Du; Chun Wang; Xiao-quan Lu

    2008-01-01

    Dual fluorescence and UV absorption of 2'-ethylhexyl 4-(N,N-dimethylamino)benzoate (EHDMAB) were investigated in cationic,non-ionic and anionic miceUes.When EHDMAB was solubilized in different micellss, the UV absorption of EHDMAB was enhanced.Twisted intramolecular charge transfer (TICT) emission with longer wavelength was observed in ionic micelles,whereas TICT emission with shorter wavelength was obtained in non-ionic micelles.In particular,dual fluorescence of EHDMAB was significantly quenched by the positively charged pyridinium ions arranged in the Stern layer of cationic micelles.UV radiation absorbed mainly decays via TICT emission and radiationless deactivation.The dimethylamino group of EHDMAB experiences different polar environments in ionic and non-ionic micelles according to the polarity dependence of TICT emission of EHDMAB in organic solvents.In terms of the molecular structures and sizes of EHDMAB and surfactants,each individual EHDMAB molecule should be buried in micelles with its dimethylamino group toward the polar head groups of different micelles and with its 2'-ethylhexyl chain toward the hydrophobic micellar core.Dynamic fluorescence quenching measurements of EHDMAB provide further support for the location of EHDMAB in different micelles.

  9. Simultaneous determination of a quaternary mixture of oxomemazine, sodium benzoate, guaifenesin and paracetamol by chromatographic methods

    Directory of Open Access Journals (Sweden)

    Nehal F. Farid

    2014-12-01

    Full Text Available The aim of the present work was to develop simple, accurate, sensitive and selective methods for the simultaneous determination of oxomemazine (Ox, sodium benzoate (SB, guaifenesin (Gu, andparacetamol (Par. Two methods were described and validated for the simultaneous determination of the four drugs in syrup and suppositories. The first method was a reversed phase HPLC and UVdetection at 220 nm. The assay was performed using C 18 column and an isocratic elution using acetonitrile – methanol – 35 mM KH2PO4 (20: 5: 75; by volume, pH was adjusted to 2.9 ± 0.1 as the mobile phase. The flow rate was 1.5 mL/min and separation was achieved in less than 15 min. The second method was a TLC- spectrodensitometric method, used to separate, identify and quantify the four drugs when present in combination. The drugs were applied on silica gel plates and development was made using methylene chloride- methanol- acetic acid- 33% ammonia (89: 8.4: 2: 0.6, by volume as a mobile phase. The bands of the four drugs were quantified by scanning spectrodensitometricaly at 270 nm. The suggested chromatographic methods were validated and applied successfully to the analysis of the syrup and suppositories.

  10. High secondary [alpha]-deuterium kinetic isotope effect in the acetolysis and formolysis of dideuterioferrocenylmethyl benzoate

    Energy Technology Data Exchange (ETDEWEB)

    Asperger, S. (Research Center of the Croatian Academy of Sciences and Arts, Zagreb (Croatia)); Kukric, Z.; Sutic, D. (Sarajevo Univ. (Yugoslavia). Faculty of Natural Sciences and Mathematics); Saunders, W.H. Jr. (Rochester Univ., NY (United States). Dept. of Chemistry)

    1992-02-01

    Acetolysis and formolysis of dideuterioferrocenylmethyl benzoate exhibit large secondary deuterium kinetic isotope effects and an abnormal temperature dependence. In the presence of LiClO[sub 4], which prevents the reversion from solvent-separated to contact ion-pairs, K[sub H]/K[sub D] at 25 [sup o]C amount to 1.53 [+-] 0.02 (acetolysis) and 1.48 [+-] 0.03 (formolysis). In the presence of LiClO[sub 4] the ratios of Arrhenius pre-exponential factors, A[sub H]/A[sub D], are significantly less than unity and amount to 0.49 [+-] 0.01 (acetolysis) and 0.38 [+-] 0.04 (formolysis). In the absence of LiClO[sub 4] the A[sub H]/A[sub D] ratios are much smaller (0.02 both in acetolysis and formolysis). We suggest that these surprisingly low values result from a change in rate-determining step over the temperature range, from formation of the solvent-separated ion-pair at low temperatures to reaction of the dissociated carbocation with solvent at the highest temperatures. Whether tunnelling plays any role in these solvolyses is discussed. (Author).

  11. Management recommendations: Bear River

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This document is a review of land management practices at the Bear River Migratory Bird Refuge, by a land use specialist. Recommendations, time frame and additional...

  12. Rolling bearing analysis

    CERN Document Server

    Harris, Tedric A

    2001-01-01

    One of the most well-known experts in the field brings cutting-edge research to practitioners in the new edition of this important reference. Covers the improved mathematical calculations for rolling bearing endurance developed by the American Society of Mechanical Engineers and the Society of Lubrication and Tribology Engineers. Updated with new material on Condition-Based Maintenance, new testing methods, and new bearing materials.

  13. Gear bearing drive

    Science.gov (United States)

    Weinberg, Brian (Inventor); Mavroidis, Constantinos (Inventor); Vranish, John M. (Inventor)

    2011-01-01

    A gear bearing drive provides a compact mechanism that operates as an actuator providing torque and as a joint providing support. The drive includes a gear arrangement integrating an external rotor DC motor within a sun gear. Locking surfaces maintain the components of the drive in alignment and provide support for axial loads and moments. The gear bearing drive has a variety of applications, including as a joint in robotic arms and prosthetic limbs.

  14. My Little Teddy Bear

    Institute of Scientific and Technical Information of China (English)

    钱佳楠

    2005-01-01

    @@ As Valentine's Day came closer,every shop was full of colourful gifts such as cookies in the shape of heart, chocolates,Teddy Bears and so on.When I step into a shop on February 14th,I felt most lonely as I was alone.With mv eves fixed on a lovely Teddy Bear, I wished that someone could send me this stuffed toy.

  15. Determination of Benzoate Level in Canned Pickles and Pickled Cucumbers in Food Producing Factories in Markazi Province and those that their Products were Sold in Arak City, Iran

    Directory of Open Access Journals (Sweden)

    Mostafa Delavar

    2012-11-01

    Full Text Available Background: Anecdotal information has suggested that sodium benzoate is used with more than permissible doses during production steps of food products especially pickles and pickled cucumbers in food producing factories in Markazi province and other food producing factories . The present study was done to evaluate factual concentration of sodium benzoate in these products. Methods: In this study, 8 samples from canned pickled cucumbers and 10 samples from canned pickles were randomly gathered from food production factories in Markazi province between March and September 2010. Also, 25 samples from canned pickled cucumbers and 15 samples from canned pickles and 7 samples of bulk cargo pickled cucumbers were collected from the other provinces in Arak city. Sodium benzoate level was determined in the samples using UV-VIS spectrophotometry method. The determined values were analyzed by N-par test using SPSS software version 16.0. Results: Sodium benzoate level was near zero in the samples of canned pickles and pickled cucumbers from producing factories. This was 200-400 PPM in 7 samples from bulk cargo pickled cucumbers which was higher than permissible dose. There was not a statistically significant difference between mean benzoate level of canned pickles and pickled cucumbers produced in Markazi providence factories and other food factories. Benzoate level was significantly higher than permissible dose in bulk cargo pickled cucumbers. Conclusion: Food products from production factories do not have higher than permissible level of sodium benzoate; however, this is higher in bulk cargo pickled cucumbers. Hence, stricter control on bulk cargo pickled cucumber products is recommended.

  16. Climate Drives Polar Bear Origins

    Science.gov (United States)

    In their provocative analysis of northern bears (“Nuclear genomic sequences reveal that polar bears are an old and distinct bear lineage,” Reports, 20 April, p. 344), F. Hailer et al. use independent nuclear loci to show that polar bears originated during the middle Pleistocene, rather than during t...

  17. Coacervation and aggregate transitions of a cationic ammonium gemini surfactant with sodium benzoate in aqueous solution.

    Science.gov (United States)

    Wang, Ruijuan; Tian, Maozhang; Wang, Yilin

    2014-03-21

    Coacervation in an aqueous solution of cationic ammonium gemini surfactant hexamethylene-1,6-bis(dodecyldimethylammonium bromide) (C12C6C12Br2) with sodium benzoate (NaBz) has been investigated at 25 °C by turbidity titration, light microscopy, dynamic light scattering, cryogenic temperature transmission electron microscopy (Cryo-TEM), scanning electron microscopy (SEM), isothermal titration calorimetry, ζ potential and (1)H NMR measurements. There is a critical NaBz concentration of 0.10 M, only above which coacervation can take place. However, if the NaBz concentration is too large, coacervation also becomes difficult. Coacervation takes place at a very low concentration of C12C6C12Br2 and exists in a very wide concentration region of C12C6C12Br2. The phase behavior in the NaBz concentration from 0.15 to 0.50 M includes spherical micelles, threadlike micelles, coacervation, and precipitation. With increasing NaBz concentration, the phase boundaries of coacervation shift to higher C12C6C12Br2 concentration. Moreover, the C12C6C12Br2-NaBz aggregates in the coacervate are found to be close to charge neutralized. The Cryo-TEM and SEM images of the coacervate shows a layer-layer stacking structure consisting of a three-dimensional network formed by the assembly of threadlike micelles. Long, dense and almost uncharged threadlike micelles are the precursors of coacervation in the system. PMID:24651935

  18. Radial Halbach Magnetic Bearings

    Science.gov (United States)

    Eichenberg, Dennis J.; Gallo, Christopher A.; Thompson, William K.

    2009-01-01

    Radial Halbach magnetic bearings have been investigated as part of an effort to develop increasingly reliable noncontact bearings for future high-speed rotary machines that may be used in such applications as aircraft, industrial, and land-vehicle power systems and in some medical and scientific instrumentation systems. Radial Halbach magnetic bearings are based on the same principle as that of axial Halbach magnetic bearings, differing in geometry as the names of these two types of bearings suggest. Both radial and axial Halbach magnetic bearings are passive in the sense that unlike most other magnetic bearings that have been developed in recent years, they effect stable magnetic levitation without need for complex active control. Axial Halbach magnetic bearings were described in Axial Halbach Magnetic Bearings (LEW-18066-1), NASA Tech Briefs, Vol. 32, No. 7 (July 2008), page 85. In the remainder of this article, the description of the principle of operation from the cited prior article is recapitulated and updated to incorporate the present radial geometry. In simplest terms, the basic principle of levitation in an axial or radial Halbach magnetic bearing is that of the repulsive electromagnetic force between (1) a moving permanent magnet and (2) an electric current induced in a stationary electrical conductor by the motion of the magnetic field. An axial or radial Halbach bearing includes multiple permanent magnets arranged in a Halbach array ("Halbach array" is defined below) in a rotor and multiple conductors in the form of wire coils in a stator, all arranged so the rotary motion produces an axial or radial repulsion that is sufficient to levitate the rotor. A basic Halbach array (see Figure 1) consists of a row of permanent magnets, each oriented so that its magnetic field is at a right angle to that of the adjacent magnet, and the right-angle turns are sequenced so as to maximize the magnitude of the magnetic flux density on one side of the row while

  19. Partial tooth gear bearings

    Science.gov (United States)

    Vranish, John M. (Inventor)

    2010-01-01

    A partial gear bearing including an upper half, comprising peak partial teeth, and a lower, or bottom, half, comprising valley partial teeth. The upper half also has an integrated roller section between each of the peak partial teeth with a radius equal to the gear pitch radius of the radially outwardly extending peak partial teeth. Conversely, the lower half has an integrated roller section between each of the valley half teeth with a radius also equal to the gear pitch radius of the peak partial teeth. The valley partial teeth extend radially inwardly from its roller section. The peak and valley partial teeth are exactly out of phase with each other, as are the roller sections of the upper and lower halves. Essentially, the end roller bearing of the typical gear bearing has been integrated into the normal gear tooth pattern.

  20. Blood Pump Bearing System

    Science.gov (United States)

    Aber, Gregory S. (Inventor)

    2000-01-01

    An apparatus is provided for a blood pump bearing system within a pump housing to support long-term highspeed rotation of a rotor with an impeller blade having a plurality of individual magnets disposed thereon to provide a small radial air gap between the magnets and a stator of less than 0.025 inches. The bearing system may be mounted within a flow straightener, diffuser, or other pump element to support the shaft of a pump rotor. The bearing system includes a zirconia shaft having a radiused end. The radiused end has a first radius selected to be about three times greater than the radius of the zirconia shaft. The radiused end of the zirconia shaft engages a flat sapphire endstone. Due to the relative hardness of these materials a flat is quickly produced during break-in on the zirconia radiused end of precisely the size necessary to support thrust loads whereupon wear substantially ceases. Due to the selection of the first radius, the change in shaft end-play during pump break-in is limited to a total desired end-play of less than about 0.010 inches. Radial loads are supported by an olive hole ring jewel that makes near line contact around the circumference of the Ir shaft to support big speed rotation with little friction. The width of olive hole ring jewel is small to allow heat to conduct through to thereby prevent heat build-up in the bearing. A void defined by the bearing elements may fill with blood that then coagulates within the void. The coagulated blood is then conformed to the shape of the bearing surfaces.

  1. The Little Bear

    Institute of Scientific and Technical Information of China (English)

    林战峰; 乐伟国

    2007-01-01

    @@ 一、故事内容 A little bear has a magic stick.It can make his wishes come true. One day,the little bear is walking in the forest.He sees a bird.It is flying in the sky.It has two beautiful wings."I want two beautiful wings.I wish I can fly like a bird,"he says to the magic stick.Two beautiful wings come out from his back and he can fly like a bird now.He is very happy.

  2. Silver Bear for Screenplay

    Institute of Scientific and Technical Information of China (English)

    LIU YUNYUN

    2010-01-01

    @@ Chinese director Wang Quan'an won the Silver Bear Prize at the 60th Berlin International Film Festival that lasted during February 11 to 21 tor the best screenplay for his movie Apart Together.The film also opened the festival.

  3. Hybrid superconductor magnet bearings

    Science.gov (United States)

    Chu, Wei-Kan

    1995-01-01

    Hybrid superconductor magnet bearings (HSMB's) utilize high temperature superconductors (HTS's) together with permanent magnets to form a frictionless interface between relatively rotating parts. They are low mass, stable, and do not incur expenditure of energy during normal operation. There is no direct physical contact between rotor and stator, and hence there is no wear and tear. However, just as any other applications of HTS's, it requires a very cold temperature to function. Whereas this might be perceived as a disadvantage on earth, it is of no great concern in space or on the moon. To astronomers, the moon is an excellent site for an observatory, but the cold and dusty vacuum environment on the moon precludes the use of mechanical bearings on the telescope mounts. Furthermore, drive mechanisms with very fine steps, and hence bearings with extremely low friction are needed to track a star from the moon, because the moon rotates very slowly. All aspects considered, the HSMB is about the only candidate that fits in naturally. Here, we present a design for one such bearing, capable of supporting a telescope that weighs about 3 lbs on Earth.

  4. PLASMID-ENCODED PHTHALATE CATABOLIC PATHWAY IN ARTHROBACTER KEYSERI 12B: BIOTRANSFORMATIONS OF 2-SUBSTITUTED BENZOATES AND THEIR USE IN CLONING AND CHARACTERIZATION OF PHTHALATE CATABOLISM GENES AND GENE PRODUCTS

    Science.gov (United States)

    Several 2-substituted benzoates (including 2-trifluoromethyl-, 2-chloro-, 2-bromo-, 2-iodo-, 2-nitro-, 2-methoxy-, and 2-acetyl-benzoates) were converted by phthalate-grown Arthrobacter keyseri 12B to the corresponding 2-substituted 3,4-dihydroxybenzoates (protocatechuates)...

  5. Migration of Chemotactic Bacteria Transverse to Flow in Response to a Benzoate Source Plume Created in a Saturated Sand-Packed Microcosm

    Science.gov (United States)

    Ford, R.; Boser, B.

    2012-12-01

    Bioremediation processes depend on contact between microbial populations and the groundwater contaminants that they biodegrade. Chemotaxis, the ability of bacteria to sense a chemical gradient and swim preferentially toward locations of higher concentration, can enhance the transport of bacteria toward contaminant sources that may not be readily accessible by advection and dispersion alone. A two-dimensional rectangular-shaped microcosm packed with quartz sand was used to quantify the effect of chemotaxis on the migration of bacteria within a saturated model aquifer system. Artificial groundwater was pumped through the microcosm at a rate of approximately 1 m/day. A plume of sodium benzoate was created by continuous injection into an upper port of the microcosm to generate a chemical gradient in the vertical direction transverse to flow. Chemotactic bacteria, Pseudomonas putida F1, or the nonchemotactic mutant, P. putida F1 CheA, were injected with a conservative tracer in a port several centimeters below the benzoate position. As the injectates traversed the one-meter length of the microcosm, samples were collected from a dozen effluent ports to determine vertical concentration distributions for the bacteria, benzoate and tracer. A moment analysis was implemented to estimate the center of mass, variance, and skewness of the concentration profiles. The transverse dispersion coefficient and the transverse dispersivity for chemotactic and nonchemotactic bacteria were also evaluated. Experiments performed with a continuous injection of bacteria showed that the center of mass for chemotactic bacteria was closer to the benzoate source on average than the nonchemotactic control (relative to the conservative tracer). These results demonstrated that chemotaxis can increase bacterial transport toward contaminants, potentially enhancing the effectiveness of in situ bioremediation. Experiments with 2 cm and 3 cm spacing between bacteria and benzoate injection locations were

  6. Evaluation of estradiol benzoate as a pre-treatment for oocyte recovery in sheep

    Directory of Open Access Journals (Sweden)

    Marilu Constantino Max

    2014-02-01

    Full Text Available The objective of this study was to compare the number of follicles, oocytes and the recovery rate in sheep submitted to the one-shot protocol with or without ovarian priming with estradiol benzoate (EB. Pluriparous non-lactating sheep (n=33 with an average age of five years (range 4-6 and a body condition score of 3.0±0.3 were divided into three groups. The one-shot group (n=10 was treated with a subcutaneous implant containing 1.5 mg of norgestomet from D0 to D10. The animals in this group were administered 0.04 mg of D-cloprostenol, 200 IU of follicle stimulating hormone (FSH and 300 IU of equine chorionic gonadotropin (eCG on D8. Animals in the EB group (n=11 received the same treatment as one-shot plus the administration of 0.6 mg of EB on D0. In the untreated group (n=12, the animals received no hormone stimulation. The collection of the oocytes was performed by laparotomy 36 h after the administration of gonadotropins (D10. Oocytes were searched and classified based on morphology. An increase was observed (p<0.05 in the number of follicles aspirated in the one-shot vs. the EB and untreated groups (16.3±5.6 vs. 9.5±2.4 and 12.1±4.1, respectively. The average number of oocytes and the recovery rate were higher (p<0.05 in the one-shot and EB groups compared to the untreated group, resulting in 14.2±9.0 and 87.1% (142/163, 11.0±6.2 and 91.4% (122/134 vs. 6.8±3.5 and 71.9% (82/114, respectively. It was concluded that the EB did not improve efficiency in the oneshot protocol, but was significantly better than in untreated animals

  7. Induction of parturition in swine with prostaglandin F(2)alpha, estradiol benzoate and oxytocin.

    Science.gov (United States)

    Gall, M A; Day, B N

    1987-03-01

    Pregnant sows and gilts were administered either 0, 2.5, 5, 10 or 20 mg prostaglandin F(2)alpha (PGF(2)alpha) intramuscularly on Day 112 or 113 of gestation at 0800 h in an effort to induce parturition. The average interval from PGF(2)alpha injection to farrowing was 55.1 +/- 5.7, 29.4 +/- 3.1, 32.1 +/- 4.6, 27.8 +/- 1.8 and 26.9 +/- 1.1 h for 0, 2.5, 5, 10 and 20 mg, respectively. All PGF(2)alpha treatments increased (P gestation length was significantly shorter in treated gilts; however, no detrimental effect on pig performance or pig survivability was observed. A second trial evaluated the effect of a 10-mg dose of PGF(2)alpha on the induction of parturition in sows in order to obtain a majority of sows farrowing within normal working hours (0700 to 1700 h). The interval from injection to farrowing was decreased (P < 0.05) by PGF(2)alpha treatment (66.2 +/- 5.3 vs 28.1 +/- 2.2 h). Fifty-seven percent (P < 0.05) of PGF(2)alpha-treated sows farrowed between 0700 and 1700 h as compared to 13.6% for control sows. A third trial was conducted to examine a sequential treatment of PGF(2)alpha and oxytocin to control the time of parturition more precisely. Sows receiving only 10 mg of PGF(2)alpha farrowed on an average 31.1 +/- 1.4 h after injection. The injection of 40 IU oxytocin 24 to 28 h after PGF(2)alpha decreased (P < 0.05) the interval from PGF(2)alpha to farrowing (28.1 +/- 0.9 h). The addition of oxytocin increased (P < 0.05) the number of sows farrowing within 3 h of injection (33 vs 86% for PGF(2)alpha and PGF(2)alpha + oxytocin treatments, respectively). A fourth trial was designed to determine if the addition of exogenous estradiol benzoate (EB) to a sequential treatment of PGF(2)alpha and oxytocin would improve the predictability and synchronization of the induced parturition. Sows were assigned to receive either saline, 10 mg PGF(2)alpha + 40 IU oxytocin or 10 mg PGF(2)alpha + 5 mg EB + 40 IU oxytocin. The addition of EB reduced (P < 0.01) the variance in

  8. Elucidation of the thermophilic phenol biodegradation pathway via benzoate during the anaerobic digestion of municipal solid waste.

    Science.gov (United States)

    Hoyos-Hernandez, Carolina; Hoffmann, Marieke; Guenne, Angeline; Mazeas, Laurent

    2014-02-01

    Anaerobic digestion makes it possible to valorize municipal solid waste (MSW) into biogas and digestate which are, respectively, a renewable energy source and an organic amendment for soil. Phenols are persistent pollutants present in MSW that can inhibit the anaerobic digestion process and have a toxic effect on microbiota if they are applied to soil together with digestate. It is then important to define the operational conditions of anaerobic digestion which allow the complete degradation of phenol. In this context, the fate of phenol during the anaerobic digestion of MSW at 55°C was followed using an isotopic tracing approach ((13)C6-phenol) in experimental microcosms with inoculum from an industrial thermophilic anaerobic digester. With this approach, it was possible to demonstrate the complete phenol biodegradation into methane and carbon dioxide via benzoate. Benzoate is known to be a phenol metabolite under mesophilic conditions, but in this study it was found for the first time to be a phenol degradation product at thermophilic temperature.

  9. Short communication: Use of a mixture of sodium nitrite, sodium benzoate, and potassium sorbate in aerobically challenged silages.

    Science.gov (United States)

    Knicky, Martin; Spörndly, Rolf

    2015-08-01

    Aerobic instability is still a common problem with many types of silages, particularly well-fermented silages. This study evaluated the effect of adding an additive mixture based on sodium nitrite, sodium benzoate, and potassium sorbate to a variety of crop materials on fermentation quality and aerobic stability of silages. Ensiling conditions were challenged by using a low packing density (104±4.3kg of dry matter/m(3)) of forage and allowing air ingression into silos (at 14 and 7 d before the end of the storage, for 8 h per event). Additive-treated silages were found to have significantly lower pH and reduced formation of ammonia-N, 2.3-butanediol, and ethanol compared with untreated control silages. Yeast growth was significantly reduced by additive treatment in comparison with untreated control silage. Consequently, additive-treated silages were considerably more aerobically stable (6.7 d) than untreated control silages (0.5 d). Overall, adding 5mL/kg of fresh crop of the additive based on sodium nitrite, sodium benzoate, and potassium sorbate reduced undesirable microorganisms in silages and thereby provided suitable ensiling conditions and prolonged aerobic stability, even under air-challenged laboratory ensiling conditions. PMID:26026758

  10. Effectiveness of sodium benzoate as a freshwater low toxicity antifoulant when dispersed in solution and entrapped in silicone coatings.

    Science.gov (United States)

    Haque, Haroon; Cutright, Teresa J; Newby, Bi-Min Zhang

    2005-01-01

    The traditional solution for preventing organisms from attaching to submerged surfaces is to apply antifouling coatings or biocides. Based on the varied defence mechanisms exhibited by biofilms, the antifoulant needs to prevent bacterial attachment during the early stages of biofilm formation. The potential of benzoic acid and sodium benzoate (NaB) as antifoulants for deterring freshwater bacterial attachment was evaluated with the antifoulants dispersed in solution or entrapped in silicone coatings. Effectiveness was based on the decrease in microbial attachment, limited toxicity, and minimum alteration of the properties of the coatings. The optimal NaB concentration when dispersed in solution, 700 mg l-1, resulted in a biofilm surface coverage of only 3.34% after four weeks. The model silicone, Sylgard 184, demonstrated a better overall performance than the commercial coating, RTV11. Sylgard 184 containing sodium benzoate had 41-52% less biofilm in comparison to the control Sylgard 184, whereas both the control and NaB-entrapped RTV11 coatings had significant biofilm coverage.

  11. Elucidation of the thermophilic phenol biodegradation pathway via benzoate during the anaerobic digestion of municipal solid waste.

    Science.gov (United States)

    Hoyos-Hernandez, Carolina; Hoffmann, Marieke; Guenne, Angeline; Mazeas, Laurent

    2014-02-01

    Anaerobic digestion makes it possible to valorize municipal solid waste (MSW) into biogas and digestate which are, respectively, a renewable energy source and an organic amendment for soil. Phenols are persistent pollutants present in MSW that can inhibit the anaerobic digestion process and have a toxic effect on microbiota if they are applied to soil together with digestate. It is then important to define the operational conditions of anaerobic digestion which allow the complete degradation of phenol. In this context, the fate of phenol during the anaerobic digestion of MSW at 55°C was followed using an isotopic tracing approach ((13)C6-phenol) in experimental microcosms with inoculum from an industrial thermophilic anaerobic digester. With this approach, it was possible to demonstrate the complete phenol biodegradation into methane and carbon dioxide via benzoate. Benzoate is known to be a phenol metabolite under mesophilic conditions, but in this study it was found for the first time to be a phenol degradation product at thermophilic temperature. PMID:24238916

  12. [Analysis of preservatives used in cosmetic products: salicylic acid, sodium benzoate, sodium dehydroacetate, potassium sorbate, phenoxyethanol, and parabens].

    Science.gov (United States)

    Ikarashi, Yoshiaki; Uchino, Tadashi; Nishimura, Tetsuji

    2010-01-01

    Preservatives are used to inhibit the growth of microorganisms in cosmetic products. The Japanese standards for cosmetics set restrictions on the maximum amount of each preservative added to cosmetics as per the purpose of use of cosmetics. For the investigation into the actual conditions of commonly used preservatives in commercial cosmetics, we analyzed parabens, phenoxyethanol, sodium benzoate, sodium dehydroacetate, salicylic acid, and potassium sorbate by high-performance liquid chromatography (HPLC). Twenty-one samples were obtained from cosmetic product manufacturers located in 14 prefectures in Japan. Among different acid- and salt-based preservatives, sodium benzoate was observed to have been used in many products. These acid- and salt-based preservatives were used with parabens in personal washing products, such as shampoo and soap. The labels of two of the cosmetic product samples displayed inaccurate ingredient information, that is, a preservative other than the one used in the corresponding product was listed on them. The amount of preservatives used did not exceed regulatory limits in any of the analyzed samples.

  13. Magnetic bearings grow more attractive

    Science.gov (United States)

    1993-10-01

    Advances in materials and electronics have enabled designers to devise simpler, smaller magnetic bearings. As a result, costs have dropped, widening the applications for these very-low-friction devices. Avcon (Advanced Controls Technology) has patented a permanent-magnet bias actively controlled bearing. Here high-energy rare earth permanent-magnet materials supply the basic bearing load levitation, while servo-driven electromagnets generate stabilization and centering forces for motion contol. Previous heavy-duty magnetic bearings used electromagnets entirely for suspension and control, which led to large bearings and control systems with higher power requirements. Avcon has developed several types of permanent-magnet bias bearings. The simplest is the radial repulsion bearing. Avcon's homopolar permanent-magnet bias active bearing is the most versatile of the company's designs.

  14. Government Risk-Bearing

    CERN Document Server

    1993-01-01

    The u.s. government bulks large in the nation's financial markets. The huge volume of government-issued and -sponsored debt affects the pricing and volume ofprivate debt and, consequently, resource allocation between competing alternatives. What is often not fully appreciated is the substantial influence the federal government wields overresource allocation through its provisionofcreditandrisk-bearing services to the private economy. Because peopleand firms generally seekto avoid risk, atsomeprice they are willing to pay another party to assume the risk they would otherwise face. Insurance companies are a class of private-sector firms one commonly thinks of as providing these services. As the federal government has expanded its presence in the U.S. economy during this century, it has increasingly developed programs aimed at bearing risks that the private sector either would not take on at any price, or would take on but atapricethoughtto besogreatthatmostpotentialbeneficiarieswouldnotpurchase the coverage. To...

  15. Passive magnetic bearing system

    Science.gov (United States)

    Post, Richard F.

    2014-09-02

    An axial stabilizer for the rotor of a magnetic bearing provides external control of stiffness through switching in external inductances. External control also allows the stabilizer to become a part of a passive/active magnetic bearing system that requires no external source of power and no position sensor. Stabilizers for displacements transverse to the axis of rotation are provided that require only a single cylindrical Halbach array in its operation, and thus are especially suited for use in high rotation speed applications, such as flywheel energy storage systems. The elimination of the need of an inner cylindrical array solves the difficult mechanical problem of supplying support against centrifugal forces for the magnets of that array. Compensation is provided for the temperature variation of the strength of the magnetic fields of the permanent magnets in the levitating magnet arrays.

  16. Centrifugally decoupling touchdown bearings

    Science.gov (United States)

    Post, Richard F

    2014-06-24

    Centrifugally decoupling mechanical bearing systems provide thin tensioned metallic ribbons contained in a support structure. This assembly rotates around a stationary shaft being centered at low speeds by the action of the metal ribbons. Tension springs are connected on one end to the ribbons and on the other end to the support structure. The ribbons pass through slots in the inner ring of the support structure. The spring preloading thus insures contact (or near-contact) between the ribbons and the shaft at rotation speeds below the transition speed. Above this speed, however, the centrifugal force on the ribbons produces a tensile force on them that exceeds the spring tensile force so that the ribbons curve outward, effectively decoupling them from mechanical contact with the shaft. They still remain, however, in position to act as a touchdown bearing in case of abnormally high transverse accelerations.

  17. Magnetic bearing and motor

    Science.gov (United States)

    Studer, Philip A. (Inventor)

    1983-01-01

    A magnetic bearing assembly (10) has an intermediate rotatable section (33) having an outer cylindrical member (30) coaxially suspended by a torsion wire (72) around an axially polarized cylindrical magnet (32). Axial alignment between the pole faces (40-43) of the intermediate section (33) and end surfaces (50-53) of opposed end bells (20, 22) provides a path of least reluctance across intervening air gaps (60-63) for the magnetic flux emanating from magnet (32). Radial dislocation increases the reluctance and creates a radial restoring force. Substitution of radially polarized magnets 107 fixed to a magnetically permeable cylinder (32') and insertion of pairs of armature coil windings (109-112) between the cylinder pair (33') provides an integral magnetic bearing and torsion motor (100) able to provide arcuately limited rotational drive.

  18. Rotating plug bearing and seal

    International Nuclear Information System (INIS)

    Disclosed is a bearing and seal structure for nuclear reactors utilizing rotating plugs above the nuclear reactor vessel. The structure permits lubrication of bearings and seals of the rotating plugs without risk of the lubricant draining into the reactor vessel below. The structure permits lubrication by utilizing a rotating outer race bearing. 19 claims, 3 figures

  19. Rotating plug bearing and seal

    Science.gov (United States)

    Wade, Elman E.

    1977-01-01

    A bearing and seal structure for nuclear reactors utilizing rotating plugs above the nuclear reactor vessel. The structure permits lubrication of bearings and seals of the rotating plugs without risk of the lubricant draining into the reactor vessel below. The structure permits lubrication by utilizing a rotating outer race bearing.

  20. Magnetic translator bearings

    Science.gov (United States)

    Hockney, Richard L. (Inventor); Downer, James R. (Inventor); Eisenhaure, David B. (Inventor); Hawkey, Timothy J. (Inventor); Johnson, Bruce G. (Inventor)

    1990-01-01

    A magnetic bearing system for enabling translational motion includes a carriage and a shaft for movably supporting the carriage; a first magnetic bearing fixed to one of the carriage and shaft and slidably received in a first channel of the other of the carriage and shaft. The first channel is generally U shaped with two side walls and a back wall. The magnetic bearing includes a pair of spaced magnetic pole pieces, each pole piece having a pair of electromagnetic coils mounted on poles on opposite ends of the pole piece proximate the side walls, and a third electromagnetic coil mounted on a pole of the pole piece proximate the backwall; a motion sensor for sensing translational motion along two axes and rotationally about three axes of the carriage and shaft relative to each other; and a correction circuit responsive to the sensor for generating a correction signal to drive the coils to compensate for any misalignment sensed between the carriage and the shaft.

  1. Dispersive liquid-liquid microextraction followed by high-performance liquid chromatography for determination of benzoate and sorbate in yogurt drinks and method optimization by central composite design.

    Science.gov (United States)

    Kamankesh, Marzieh; Mohammadi, Abdorreza; Tehrani, Zohreh Modarres; Ferdowsi, Roohallah; Hosseini, Hedayat

    2013-05-15

    A new method based on dispersive liquid-liquid microextraction (DLLME) followed by high-performance liquid chromatography (HPLC) for determination of benzoate and sorbate salts in yogurt drinks was developed. The effective parameters in DLLME process, including volume of extraction and disperser solvents, pH and salt effect, were optimized using response surface methodology (RSM) based on central composite design. The yogurt drink samples were extracted using NaOH and Carrez solutions (potassium hexaferrocyanide and zinc acetate) were used for sedimentation of proteins. For DLLME, a mixture of extraction solvent (1-octanol) and disperser solvent (ethanol) was rapidly injected into the sample solution by syringe and cloudy solution is formed. Subsequently, the upper 1-octanol layer was analyzed by HPLC. The detection limits for benzoate and sorbate were 0.06 ng mL(-1) and 0.15 ng mL(-1), respectively. The relative standard deviations (RSD) for seven analyses were 4.96% for benzoate and 4.58% for sorbate. The proposed method demonstrated good linearity and high enrichment factor. A clean separation and good chromatogram is readily achieved without the presence of matrix interference. A comparison of this method with previous methods demonstrated that the proposed method is an accurate, rapid and reliable sample-pretreatment method that gives very good enrichment factors and detection limits for extracting and determining sorbate and benzoate in yogurt drink samples. PMID:23618139

  2. 长期烫吸安钠咖对肝功能的影响%EFFECT OF LONG- TERM USE OF CAFFEINE SODIUM BENZOATE ON LIVER FUNCTION

    Institute of Scientific and Technical Information of China (English)

    黄永清; 张宪武; 王志纲

    2011-01-01

    目的:探讨长期烫吸安钠咖对肝功的影响.方法:应用MoDULAR P800仪器,对烫吸安钠咖组36例及正常对照组14例测定肝功情况,对结果进行比较分析.结果:与对照组比较,烫吸安钠咖组的总胆红素含量低,在统计学上存在显著性差异(P<0.01);谷丙转氨酶、肌酐含量高,在统计学上存在差异(P<0.05).结论:长期烫吸安钠咖对肝功有一定的影响.%Objective :To observe the effect of long - term use of caffeine sodium benzoate on liver function. Methods:To compare the liver function of long - term users of caffeine sodium benzoate with that of the control group by MoDULAR P800 made in USA. Results: Compared with the control, the bilirubin total in the long - term users of caffeine sodium benzoate was lower, showing significant difference (P < 0.01), the glutamate pyruvate transaminase, creatinine were higher(P < 0.05). Conclusion: Long - term use of caffeine sodium benzoate can influence the users' liver function to some extent.

  3. Damping Bearings In High-Speed Turbomachines

    Science.gov (United States)

    Von Pragenau, George L.

    1994-01-01

    Paper presents comparison of damping bearings with traditional ball, roller, and hydrostatic bearings in high-speed cryogenic turbopumps. Concept of damping bearings described in "Damping Seals and Bearings for a Turbomachine" (MFS-28345).

  4. Effect of Bearing Cleaning on Long Term Bearing Life

    Science.gov (United States)

    Jett, Tim; Thom, R. L.

    1999-01-01

    For many years chlorofluorocarbon (CFC) based solvents, such as CFC-113 and 1,1,1, trichloroethane (TCA), were used as bearing cleaning solvents for space mechanism bearings. The 1995 ban on the production of ozone depleting chemicals (ODC) such as CFCs caused a change requiring the use of ODC-free cleaners for precision bearing cleaning. With this change the question arises; what effect if any do these new cleaners have on long term bearing life? The purpose of this study was to evaluate this effect. A one year test using 60 small electrical motors (two bearings per motor) was conducted in a high vacuum environment (2.0 x 10(exp -6) torr) at a temperature of 90 C. Prior to testing the bearings were cleaned with one of four cleaners. These cleaners included two aqueous based cleaners, a CFC based cleaner and supercritical carbon dioxide. Three space compatible greases were tested. After testing, the mass of each lubricated bearing was measured both pre and post test. Along with mass loss measurements a profilometer trace of each bearing was taken to measure post test wear of the bearings. In addition, the bearings were visually examined and analyzed using an optical microscope.

  5. Introgressive hybridization: brown bears as vectors for polar bear alleles.

    Science.gov (United States)

    Hailer, Frank

    2015-03-01

    The dynamics and consequences of introgression can inform about numerous evolutionary processes. Biologists have therefore long been interested in hybridization. One challenge, however, lies in the identification of nonadmixed genotypes that can serve as a baseline for accurate quantification of admixture. In this issue of Molecular Ecology, Cahill et al. (2015) analyse a genomic data set of 28 polar bears, eight brown bears and one American black bear. Polar bear alleles are found to be introgressed into brown bears not only near a previously identified admixture zone on the Alaskan Admiralty, Baranof and Chichagof (ABC) Islands, but also far into the North American mainland. Elegantly contrasting admixture levels at autosomal and X chromosomal markers, Cahill and colleagues infer that male-biased dispersal has spread these introgressed alleles away from the Late Pleistocene contact zone. Compared to a previous study on the ABC Island population in which an Alaskan brown bear served as a putatively admixture-free reference, Cahill et al. (2015) utilize a newly sequenced Swedish brown bear as admixture baseline. This approach reveals that brown bears have been impacted by introgression from polar bears to a larger extent (up to 8.8% of their genome), than previously known, including the bear that had previously served as admixture baseline. No evidence for introgression of brown bear into polar bear is found, which the authors argue could be a consequence of selection. Besides adding new exciting pieces to the puzzle of polar/brown bear evolutionary history, the study by Cahill and colleagues highlights that wildlife genomics is moving from analysing single genomes towards a landscape genomics approach. PMID:25775930

  6. Bearings only naval tracking

    Energy Technology Data Exchange (ETDEWEB)

    Barth, M.J.

    1984-11-01

    Two commonly used Extended Kalman Filter tracking algorithms utilize the Relative Cartesian and Modified Polar coordinate systems. This report compares the two algorithms by exercising a destroyer-Submarine (DD/SS) computer simulation. A simple engagement geometry is employed which encompasses the major DD/SS options available. Error statistics are developed by Monte Carlo methods. Results are presented which show that the circular error depends upon the diagonal values of the error covariance matrix. The results also support (but do not establish) that the optimum DD manuevuer is that which minimizes the range while maximizing the bearing rate. 4 refs., 5 figs., 4 tabs.

  7. Design, synthesis, molecular docking studies and in vitro screening of ethyl 4-(3-benzoylthioureido) benzoates as urease inhibitors.

    Science.gov (United States)

    Saeed, Aamer; Khan, Muhammad Siraj; Rafique, Hummera; Shahid, Mohammad; Iqbal, Jamshed

    2014-02-01

    Thioureas are exceptionally versatile building blocks towards the synthesis of wide variety of heterocyclic systems, which also possess extensive range of pharmacological activities. The substituted benzoic acids were converted into corresponding acid chlorides, these acid chlorides were then treated with potassium thiocyanate in acetone and then the reaction mixture was refluxed for 1-2h afford ethyl 4-(3-benzoylthioureido)benzoates thioureas in good yields. All the newly synthesized compounds were evaluated for their urease inhibitory activities and were found to be potent inhibitors of urease enzyme. Compounds 1f and 1g were identified as the most potent urease inhibitors (IC50 0.21 and 0.13 μM, respectively), and was 100-fold more potent than the standard inhibitors. Further molecular docking studies were carried out using the crystal structure of urease to find out the binding mode of the inhibitors with the enzyme. PMID:24269986

  8. Growth and characterization of nonlinear optical single crystals: bis(cyclohexylammonium) terephthalate and cyclohexylammonium para-methoxy benzoate

    Indian Academy of Sciences (India)

    P Sathya; M Anantharaja; N Elavarasu; R Gopalakrishnan

    2015-09-01

    Bis(cyclohexylammonium) terephthalate (BCT) and cyclohexylammonium 4-methoxy benzoate (C4MB) single crystals were successfully grown by the slow evaporation solution growth technique. The harvested crystals were subjected to single-crystal X-ray diffraction, spectral, optical, thermal and mechanical studies in order to evaluate physiochemical properties. The Kurtz and Perry technique for second harmonic generation (SHG) study revealed that the powdered materials of BCT and C4MB exhibit SHG efficiency 0.2 times less and 1.3 times greater than that of standard reference material potassium dihydrogen phosphate. C4MB crystal exhibits high efficiency than BCT, because of methoxy group substituted in the para position of phenyl ring. With high SHG efficiency and thermal stability para substituted C4MB crystal will be a potential candidate for optical device fabrication.

  9. Di-μ-iodido-bis(iodido{methyl 4-[(pyridin-2-ylmethylideneamino]benzoate-κ2N,N′}cadmium

    Directory of Open Access Journals (Sweden)

    Tushar S. Basu Baul

    2013-11-01

    Full Text Available The complete binuclear molecule of the title compound, [Cd2I4(C14H12N2O22], is generated by the application of a centre of inversion. The Cd—I bond lengths of the central core are close and uniformly longer than the exocyclic Cd—I bond. The coordination sphere of the CdII atom is completed by two N atoms of a chelating methyl 4-[(pyridin-2-ylmethylideneamino]benzoate ligand, and is based on a square pyramid with the terminal I atom in the apical position. The three-dimensional crystal packing is stabilized by C—H...O and C—H...π interactions, each involving the pyridine ring.

  10. Nanoprecipitation in bearing steels

    Energy Technology Data Exchange (ETDEWEB)

    Barrow, A.T.W. [SKF University Technology Centre, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom); Rivera-Diaz-del-Castillo, P.E.J., E-mail: pejr2@cam.ac.uk [SKF University Technology Centre, Department of Materials Science and Metallurgy, University of Cambridge, Cambridge CB2 3QZ (United Kingdom)

    2011-11-15

    {theta}-phase is the main hardening species in bearing steels and appears in both martensitically and bainitically hardened microstructures. This work presents a survey of the microstrucural features accompanying nanoprecipitation in bearing steels. Nanoprecipitate structures formed in 1C-1.5Cr wt.% with additions of Cr, Mn, Mo, Si and Ni are studied. The work is combined with thermodynamic calculations and neural networks to predict the expected matrix composition, and whether this will transform martensitically or bainitically. Martensite tetragonality, composition and the amount of retained austenite are related to hardness and the type of nanoprecipitate structures in martensitic grades. The {theta}-phase volume fraction, the duration of the bainite to austenite transformation and the amount of retained austenite are related to hardness and a detailed quantitative description of the precipitate nanostructures. Such description includes compositional studies using energy-dispersive spectroscopy, which shows that nanoprecipitate formation takes place under paraequilibrium. Special attention is devoted to a novel two-step bainite tempering process which shows maximum hardness; we prove that this is the most effective process for incorporating solute into the precipitates, which are finer than those resulting from one-step banitic transformation processes.

  11. VALIDATION OF CLEANING PROCEDURE FOR ELIMINATION OF OFLOXACIN AND METRONIDAZOLE BENZOATE FROM MIXING EQUIPMENT BY USING UV SPECTROSCOPY

    Directory of Open Access Journals (Sweden)

    Nirav B. Patel et al.

    2012-07-01

    Full Text Available This research manuscript describes simple, sensitive, accurate, precise and repeatable UV spectroscopic method for the simultaneous determination of Metronidazole (MET and Ofloxacin (OFL in suspension dosage form. Metronidazole has absorbance maxima at 318.0 nm and Ofloxacin has absorbance maxima at 294 nm in Methanol and Water (50:50 solvent. The linearity was obtained in the concentration range of 1-13 μg/ml for Metronidazole and 1-13 µg/ml for Ofloxacin with mean accuracies 99.73 ± 0.05 and 99.13 ± 0.41 for Metronidazole and Ofloxacin, respectively. This paper presents a useful UV spectroscopic method for validating equipment cleaning procedures and verifying cleaning in a pharmaceutical plant. The study summarizes the initial steps that should be taken into account and focuses particularly on the solutions to some of the most critical considerations (e.g., detection and quantification limits, recovery. Cleaning validation is the process of assuring that cleaning procedures effectively remove the residue from manufacturing equipment/facilities below a predetermined level. This is necessary to assure the quality of future products using the equipment, to prevent cross-contamination, and as a World Health Organization Good Manufacturing Practices requirement. In this article we discuss the UV method that we developed for measuring residual of Ofloxacin and Metronidazole benzoate suspension contain ofloxacin (50mg/5ml and metronidazole benzoate equivalent to metronidazole (100mg/5ml on surface of mixing tank during manufacturing process. The method with correlation coefficient R² = 0.999 and method offers low detection capability and rapid sample analysis time. The accurate recovery values with method precision less than 2%RSD of precision, UV method is applicable for determining residual of suspension on pharmaceutical equipment surfaces and will be useful for cleaning validation.

  12. Computational design of rolling bearings

    CERN Document Server

    Nguyen-Schäfer, Hung

    2016-01-01

    This book comprehensively presents the computational design of rolling bearings dealing with many interdisciplinary difficult working fields. They encompass elastohydrodynamics (EHD), Hertzian contact theory, oil-film thickness in elastohydrodynamic lubrication (EHL), bearing dynamics, tribology of surface textures, fatigue failure mechanisms, fatigue lifetimes of rolling bearings and lubricating greases, Weibull distribution, rotor balancing, and airborne noises (NVH) in the rolling bearings. Furthermore, the readers are provided with hands-on essential formulas based on the up-to-date DIN ISO norms and helpful examples for computational design of rolling bearings. The topics are intended for undergraduate and graduate students in mechanical and material engineering, research scientists, and practicing engineers who want to understand the interactions between these working fields and to know how to design the rolling bearings for automotive industry and many other industries.

  13. Grease lubrication in rolling bearings

    CERN Document Server

    Lugt, Piet M

    2012-01-01

    The definitive book on the science of grease lubrication for roller and needle bearings in industrial and vehicle engineering. Grease Lubrication in Rolling Bearings provides an overview of the existing knowledge on the various aspects of grease lubrication (including lubrication systems) and the state of the art models that exist today. The book reviews the physical and chemical aspects of grease lubrication, primarily directed towards lubrication of rolling bearings. The first part of the book covers grease composition, properties and rheology, including thermal

  14. Hydrostatic and hybrid bearing design

    CERN Document Server

    Rowe, W B

    1983-01-01

    Hydrostatic and Hybrid Bearing Design is a 15-chapter book that focuses on the bearing design and testing. This book first describes the application of hydrostatic bearings, as well as the device pressure, flow, force, power, and temperature. Subsequent chapters discuss the load and flow rate of thrust pads; circuit design, flow control, load, and stiffness; and the basis of the design procedures and selection of tolerances. The specific types of bearings, their design, dynamics, and experimental methods and testing are also shown. This book will be very valuable to students of engineering des

  15. Dynamic Analysis of Engine Bearings

    Directory of Open Access Journals (Sweden)

    H. Hirani

    1999-01-01

    Full Text Available This paper presents a simple methodology to evaluate the stiffness and damping coefficients of an engine bearing over a load cycle. A rapid technique is used to determine the shaft ‘limit cycle’ under engine dynamic loads. The proposed theoretical model is based on short and long bearing approximations. The results obtained by present approximation are compared with those obtained by numerical method. The influence of thermal effects on the stiffness and damping coefficients is predicted by using a simplified thermal analysis. In order to illustrate the application of the proposed scheme, one engine main bearing and a connecting rod bearing are analysed.

  16. Fish of Bear Lake, Utah

    OpenAIRE

    Palacios, Patsy; Luecke, Chris; Robinson, Justin

    2007-01-01

    There are 13 species of fish found in the waters of Bear Lake. Of those 13, 4 are endemic (found only in Bear Lake). The 4 endemics species are Bonneville cisco, Bonneville whitefish, Bear Lake whitefish, and Bear Lake sculpin. Five of the remaining 9 fish species are native to the region, and 4 are exotic introductions. These native fishes are the Bonneville cutthroat trout, Utah sucker, redside shiner, speckled dace and Utah chub. The exotic fishes are lake trout, common carp, yellow p...

  17. Autosizing Control Panel for Needle Bearing

    OpenAIRE

    Prof.A.R.Wadhekar,; Ms Jyoti R. Rajput

    2016-01-01

    A needle roller bearing is a bearing which uses small cylindrical rollers. Bearings are used to reduce friction of any rotating surface. Needle bearings have a large surface in contact with the bearing outer surfaces as compared to ball bearings. There is less added clearance(Diameter of the shaft and the diameter of the bearing are different) so they are much compact. The structure consists of a needle cage which contains the needle rollersthemselves and an outer race (The housin...

  18. Superconducting bearings for flywheel applications

    OpenAIRE

    Abrahamsen, A.B.

    2001-01-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found onthe applications of superconducting bearings in flywheels.

  19. High-Performance Ball Bearing

    Science.gov (United States)

    Bursey, Roger W., Jr.; Haluck, David A.; Olinger, John B.; Owen, Samuel S.; Poole, William E.

    1995-01-01

    High-performance bearing features strong, lightweight, self-lubricating cage with self-lubricating liners in ball apertures. Designed to operate at high speed (tens of thousands of revolutions per minute) in cryogenic environment like liquid-oxygen or liquid-hydrogen turbopump. Includes inner race, outer race, and cage keeping bearing balls equally spaced.

  20. What about the Javan Bear?

    NARCIS (Netherlands)

    Jentink, F.A.

    1898-01-01

    The other day I read in a dutch popular periodical a paper dealing with the different species of Bears and their geographical distribution. To my great surprise the Malayan Bear was mentioned from Java: the locality Java being quite new to me I wrote to the author of that paper and asked him some in

  1. Superconducting bearings for flywheel applications

    DEFF Research Database (Denmark)

    Abrahamsen, A.B.

    2001-01-01

    A literature study on the application of superconducting bearings in energy storage flywheel systems. The physics of magnetic levitation and superconductors are presented in the first part of the report, followed by a discussion of the literature found onthe applications of superconducting bearings...

  2. Geophagy by yellowstone grizzly bears

    Science.gov (United States)

    Mattson, D.J.; Green, G.I.; Swalley, R.

    1999-01-01

    We documented 12 sites in the Yellowstone ecosystem where grizzly bears (Ursus arctos horribilis) had purposefully consumed soil (an activity known as geophagy). We also documented soil in numerous grizzly bear feces. Geophagy primarily occurred at sites barren of vegetation where surficial geology had been modified by geothermal activity. There was no evidence of ungulate use at most sites. Purposeful consumption of soil by bears peaked first from March to May and again from August to October, synchronous with peaks in consumption of ungulate meat and mushrooms. Geophageous soils were distinguished from ungulate mineral licks and soils in general by exceptionally high concentrations of potassium (K) and high concentrations of magnesium (Mg) and sulphur (S). Our results do not support the hypotheses that bears were consuming soil to detoxify secondary compounds in grazed foliage, as postulated for primates, or to supplement dietary sodium, as known for ungulates. Our results suggest that grizzly bears could have been consuming soil as an anti-diarrheal.

  3. Assessment of matrix effects on methyl benzoate, a potential biomarker for detection of outgassed semi-volatiles from mold in indoor building materials.

    Science.gov (United States)

    Parkinson, Don-Roger; Churchill, Tonia J; Rolls, Wyn

    2008-11-01

    Methyl benzoate - as a biomarker for mold growth - was used as a specific target compound to indicate outgassed MVOC products from mold. Both real and surrogate samples were analyzed from a variety of matrices including: carpet, ceiling tiles, dried paint surfaces, wallboard and wallboard paper. Sampling parameters, including: desorption, extraction time, incubation temperature, pH, salt effects and spinning rate, were optimized. Results suggest that extraction and detection of methyl benzoate amongst other MVOCs can be accomplished cleanly by SPME-GC/MS methods. With detection limits (LOD = 1.5 ppb) and linearity (0.999) over a range of 100 ppm to 2 ppb, this work demonstrates that such a green technique can be contemplated for use in quick assessment or as part of an ongoing assessment strategy to detect mold growth in common indoor buildings and materials for both qualitative and quantitative determinations. Of importance, no matrix effects are observed under optimized extraction conditions. PMID:18777146

  4. Influence of flavone extract from cultivated saussurea on learning and memory in a mouse model of Alzheimer's disease A comparison with estradiol benzoate

    Institute of Scientific and Technical Information of China (English)

    Weiqiang Chen; Shuiming Gong; Yan Li; Ming Li; Zemin Yang; Lirong Zhang

    2011-01-01

    The present study established a mouse model of Alzheimer's disease, and investigated the effects of treatment with flavone extract from artificially cultivated saussurea. A positive control group was treated with estradiol benzoate, and learning and memory ability were examined in the 8-arm radial maze. The learning and recognition ability of mice with Alzheimer's disease treated with flavone extract was significantly improved and the number of hippocampal neurons was significantly increased in the flavone-treated and positive control groups compared with the model group. The results indicate that flavone extract from artificially cultivated saussurea can improve learning and memory deficits in mice with Alzheimer's disease, exerting effects similar to those of estradiol benzoate.

  5. Genomic evidence of geographically widespread effect of gene flow from polar bears into brown bears

    OpenAIRE

    Cahill, J.; Stirling, I.; Kistler, L.; Salamzade, R.; Ersmark, E.; Fulton, T.; Stiller, M.; Green, R.; Shapiro, B.

    2015-01-01

    Polar bears are an arctic, marine adapted species that is closely related to brown bears. Genome analyses have shown that polar bears are distinct and genetically homogeneous in comparison to brown bears. However, these analyses have also revealed a remarkable episode of polar bear gene flow into the population of brown bears that colonized the Admiralty, Baranof and Chichagof islands (ABC islands) of Alaska. Here, we present an analysis of data from a large panel of polar bear and brown bear...

  6. Siderophore-Producing Bacteria from a Sand Dune Ecosystem and the Effect of Sodium Benzoate on Siderophore Production by a Potential Isolate

    Directory of Open Access Journals (Sweden)

    Teja Gaonkar

    2012-01-01

    Full Text Available Bioremediation in natural ecosystems is dependent upon the availability of micronutrients and cofactors, of which iron is one of the essential elements. Under aerobic and alkaline conditions, iron oxidizes to Fe+3 creating iron deficiency. To acquire this essential growth-limiting nutrient, bacteria produce low-molecular-weight, high-affinity iron chelators termed siderophores. In this study, siderophore-producing bacteria from rhizosphere and nonrhizosphere areas of coastal sand dunes were isolated using a culture-dependent approach and were assigned to 8 different genera with the predominance of Bacillus sp. Studies on the ability of these isolates to grow on sodium benzoate revealed that a pigmented bacterial culture TMR2.13 identified as Pseudomonas aeruginosa showed growth on mineral salts medium (MSM with 2% of sodium benzoate and produced a yellowish fluorescent siderophore identified as pyoverdine. This was inhibited above 54 μM of added iron in MSM with glucose without affecting growth, while, in presence of sodium benzoate, siderophore was produced even up to the presence of 108 μM of added iron. Increase in the requirement of iron for metabolism of aromatic compounds in ecosystems where the nutrient deficiencies occur naturally would be one of the regulating factors for the bioremediation process.

  7. Eastern slopes grizzly bear project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    The cumulative effects of human activities on the grizzly bears in the central Canadian Rockies are not well known. As a result, a project was initiated in 1994 to address the urgent requirement for accurate scientific information on the habitat and populations of grizzly bears in the area of the Banff National Park and Kananaskis Country. This area is probably the most heavily used and developed area where the grizzly still survives. The information gathered throughout the course of this study will be used to better protect and manage the bears and other sensitive carnivores in the region. Using telemetry, researchers are monitoring 25 grizzly bears which were radio-collared in a 22,000 square-kilometer area in the upper Bow Valley drainage of the eastern Alberta slopes. The researchers involved in the project are working with representatives from Husky Oil and Talisman Energy on the sound development of the Moose Mountain oil and gas field without adversely affecting the grizzly bear population. Information collected over seven years indicated that the grizzly bears have few and infrequent offspring. Using the information gathered so far, the location of the Moose Mountain to Jumping Pound pipeline was carefully selected, since the bears recover very slowly from high mortality, and also considering that the food and cover had already been compromised by the high number of roads, trails and other human activities in the area. The status of the population and habitat of the grizzly bear will be assessed upon the conclusion of the field research phase in 2001. Models will be updated using the data obtained during eight years and will assist in the understanding of complex variables that affect grizzly bears.

  8. EFFECT OF BEARING MACROGEOMETRY ON BEARING PERFORMANCE IN ELASTOHYDRODYNAMIC LUBRICATION

    Directory of Open Access Journals (Sweden)

    Emin GÜLLÜ

    2000-01-01

    Full Text Available During manufacturing, ideal dimension and mutual positioning of machine elements proposed in project desing can be achieved only within certain range of tolerances. These tolerances, being classified in two groups, related to micro and macro geometry of machine elements, don't have to effect the functioning of these elements. So, as for all machine elements, investigation of the effects of macro and micro tolerances for journal bearings is important. In this study, we have investigated the effect of macro geometric irregularities of journal bearings on performance characteristics. In this regard, we have studied the change of bearing performance in respect to deviation from ideal circle for an elliptic shaft with small ovality rolling in circular journal bearing.

  9. Bears, Big and Little. Young Discovery Library Series.

    Science.gov (United States)

    Pfeffer, Pierre

    This book is written for children 5 through 10. Part of a series designed to develop their curiosity, fascinate them and educate them, this volume describes: (1) the eight species of bears, including black bear, brown bear, grizzly bear, spectacled bear, sun bear, sloth bear, polar bear, and giant panda; (2) geographical habitats of bears; (3)…

  10. Purification and crystallization of a putative transcriptional regulator of the benzoate oxidation pathway in Burkholderia xenovorans LB400

    International Nuclear Information System (INIS)

    The X-ray diffraction and preliminary phasing of the putative transcriptional regulator Bxe-C0898 from B. xenovorans LB400 are reported. Burkholderia xenovorans LB400 harbours two paralogous copies of the recently discovered benzoate oxidation (box) pathway. While both copies are functional, the paralogues are differentially regulated and flanked by putative transcriptional regulators from distinct families. The putative LysR-type transcriptional regulator (LTTR) adjacent to the megaplasmid-encoded box enzymes, Bxe-C0898, has been produced recombinantly in Escherichia coli and purified to homogeneity. Gel-filtration studies show that Bxe-C0898 is a tetramer in solution, consistent with previously characterized LTTRs. Bxe-C0898 crystallized with four molecules in the asymmetric unit of the P43212/P41212 unit cell with a solvent content of 61.19%, as indicated by processing of the X-ray diffraction data. DNA-protection assays are currently under way in order to identify potential operator regions for this LTTR and to define its role in regulation of the box pathway

  11. Energetic domains and conformational analysis of human serum albumin upon co-incubation with sodium benzoate and glucose.

    Science.gov (United States)

    Taghavi, F; Moosavi-Movahedi, A A; Bohlooli, M; Habibi-Rezaei, M; Hadi Alijanvand, H; Amanlou, M; Sheibani, N; Saboury, A A; Ahmad, F

    2014-01-01

    Sodium benzoate (SB), a powerful inhibitor of microbial growth, is one of the most commonly used food preservative. Here, we determined the effects of SB on human serum albumin (HSA) structure in the presence or absence of glucose after 35 days of incubation under physiological conditions. The biochemical, biophysical, and molecular approaches including free amine content assay (TNBSA assay), fluorescence, and circular dichroism spectroscopy (CD), differential scanning calorimetry (DSC), and molecular docking and LIGPLOT studies were utilized for structural studies. The TNBSA results indicated that SB has the ability to bind Lys residues in HSA through covalent bonds. The docking and LIGPLOT studies also determined another specific site via hydrophobic interactions. The CD results showed more structural helicity for HSA incubated with SB, while HSA incubated with glucose had the least, and HSA incubated with glucose + SB had medium helicity. Fluorescence spectrophotometry results demonstrated partial unfolding of HSA incubated with SB in the presence or absence of glucose, while maximum partial unfolding was observed in HSA incubated with glucose. These results were confirmed by DSC and its deconvoluted thermograms. The DSC results also showed significant changes in HSA energetic structural domains due to HSA incubation with SB in the presence or absence of glucose. Together, our studies showed the formation of three different intermediates and indicate that biomolecular investigation are effective in providing new insight into safety determinations especially in health-related conditions including diabetes.

  12. Use of estradiol benzoate to induce ovulation in a short-term protocol for fixed-time AI in sheep

    Directory of Open Access Journals (Sweden)

    Caliê Castilho

    2015-06-01

    Full Text Available The aim of this study was to test the hormonal protocol for fixed-time artificial insemination (TAI with a progesterone vaginal device for six days applying equine chorionic gonadotropin (eCG or estradiol benzoate (EB as an ovulation inducer in ewes. On day 0 (D0, the ewes (n=31 received a device containing 0.33 g of intravaginal progesterone (CIDR® and were divided into three groups. The G-CT (control group used CIDR for nine days and upon withdrawal of the progesterone, were administered prostaglandin F2 alpha (PGF2? and eCG. In the eCG (G-eCG group, CIDR was administered for six days, instead of nine as in the G-CT group, followed by PGF2a and eCG after progesterone withdrawal. In the EB (G-EB group, CIDR was also administered for six days, but eCG was not applied, and EB was used to induce ovulation 24 hours after removing the CIDR and PGF2a application. TAI was realized in all groups 50 hours after CIDR withdrawal. The pregnancy rate in the G-eCG group (66% was higher (p 0.05 compared to the G-CT group (30%. It is possible to reduce the application time of the progesterone and use eCG for TAI in sheep; however, using EB resulted in a low ovulation rate in the sheep.

  13. Synthesis, characterization and thermal behaviour of solid-state compounds of benzoates with some bivalent transition metal ions

    Directory of Open Access Journals (Sweden)

    Adriano B. Siqueira

    2007-04-01

    Full Text Available Solid-state MBz compounds, where M stands for bivalent Mn, Fe, Co, Ni, Cu and Zn and Bz is benzoate, have been synthesized. Simultaneous thermogravimetry and differential thermal analysis (TG-DTA, differential scanning calorimetry (DSC, infrared spectroscopy and complexometry were used to characterize and to study the thermal behaviour of these compounds. The procedure used in the preparation of the compounds via reaction of basic carbonates with benzoic acid is not efficient in eliminating excess acid. However the TG-DTA curves permitted to verify that the binary compounds can be obtained by thermosynthesis, because the benzoic acid can be eliminated before the thermal decomposition of these compounds. The results led to information about the composition, dehydration, thermal stability, thermal decomposition and structure of the isolated compounds. On heating, these compounds decompose in two (Mn, Co, Ni, Zn or three (Fe, Cu steps with formation of the respective oxide (Mn3O4, Fe2O3, Co3O4, NiO, CuO and ZnO as final residue. The theoretical and experimental spectroscopic studies suggest a covalent bidentate bond between ligand and metallic center.

  14. Detection on emamectin benzoate-induced apoptosis and DNA damage in Spodoptera frugiperda Sf-9 cell line.

    Science.gov (United States)

    Wu, Xiwei; Zhang, Lei; Yang, Chao; Zong, Mimi; Huang, Qingchun; Tao, Liming

    2016-01-01

    Emamectin benzoate (EMB), an important macrocyclic lactone insecticide that belongs to the avermectin family and possesses excellent potency in controlling pests, is non-carcinogenic and non-mutagenic conducted in rats and mice, but EMB-induced cytotoxicity and genotoxicity in arthropod insect have been seldom reported yet. In the present paper, we quantified the cytotoxicity of EMB through the detections on cell viability, DNA damage, and cell apoptosis in Spodoptera frugiperda Sf-9 cells in vitro. The results showed that EMB caused a concentration- and time-dependent reduction on the viability of Sf-9 cells, and the median inhibitory concentrations (IC50) were 3.34μM at 72h of exposure. The dual acridine orange/ethidium bromide staining showed that exposure to EMB induced a significant time- and concentration-dependent increase on cell apoptosis. The alkaline comet assay revealed that EMB induced significant increases on single-strand DNA breaks, and the percentage of γH2AX-positive cells represented a time- and concentration-dependent formation of DNA double-strand breaks in Sf-9 cells. Interestingly, the similar cytotoxic actions of EMB also went for the human cancerous HeLa cells as a control cell group. Data demonstrated the potential cytotoxic effect of EMB on Sf-9 cells that was significantly greater than the effect of hydrogen peroxide at the same concentrations.

  15. Synthesis, crystal structure, and fluorescence of two dimeric europium(Ⅲ) complexes with 2-(trifluoromethyl)benzoate

    Institute of Scientific and Technical Information of China (English)

    LI Yanqiu; LI Peizhou; LI Xia

    2008-01-01

    Two complexes [Eu2(2-TFMBA)6(2,2'-bipy)2].2H2O (1) and Eu2(2-TFMBA)6(1,10-phen)2 (2) (2-TFMBA=2-(Trifluoromethyl) benzoate; 2,2'-bipy=2,2'-bipyridine; 1,10-phen=1,10-phenanthroline) were synthesized by solvent method and determined by X-ray diffrac-tion analysis. Complex 1 crystallizes in monoclinic system with space group P21/c, whereas complex 2 crystallizes in triclinic system with space group P-1. Both are binuclear molecules with an inversion center. In complex 1, two center Eu3+ ions are linked together by four 2-TFMBA ligands in bidentate-bridging mode. Each Eu3+ion is eight-coordinated with six O atoms from five 2-TFMBA ligands and two N atoms from one 2,2'-bipy molecule. In complex 2, two center Eu3+ ions are linked together by four 2-TFMBA ligands in two modes, namely, bidentate-bridging and tridentate-bridging. Each Eu3+ ion is nine-coordinated with seven O atoms from five 2-TFMBA ligands and two N atoms from one 1,10-phen molecule. The two complexes both exhibited strong red fluorescence under ultraviolet light, and the 5D0→7Fj (j=0-4) transition emissions of Eu3+ ion were observed in their emission spectra.

  16. Tolerance and efficacy of emamectin benzoate and ivermectin for the treatment of Pseudocapillaria tomentosa in laboratory zebrafish (Danio rerio).

    Science.gov (United States)

    Collymore, Chereen; Watral, Virginia; White, Julie R; Colvin, Michael E; Rasmussen, Skye; Tolwani, Ravi J; Kent, Michael L

    2014-10-01

    Tolerance of adult zebrafish and efficacy of emamectin benzoate and ivermectin in eliminating Pseudocapillaria tomentosa infection were evaluated. In the tolerance study, behavioral changes, fecundity, histopathology, and mortality were evaluated for in-feed administration of emamectin (0.05, 0.10, and 0.25 mg/kg) and ivermectin (0.05 and 0.10 mg/kg). All doses of emamectin were well tolerated. Ivermectin 0.05 mg/kg administration resulted in mild behavioral changes and a transient decrease in fecundity. Ivermectin 0.10 mg/kg administration resulted in severe behavioral changes and some mortality. In the efficacy study, emamectin (0.05 and 0.25 mg/kg) and ivermectin (0.05 mg/kg) were evaluated for their efficacy in eliminating P. tomentosa infection. Emamectin reduced parasite burden in infected zebrafish, and ivermectin eliminated intestinal nematode infections. Despite a small margin of safety, ivermectin 0.05 mg/kg was effective at eliminating P. tomentosa infection in adult zebrafish. Higher doses or a longer course of treatment may be needed for complete elimination of P. tomentosa infection using emamectin. In this study, we propose two possible treatments for intestinal nematode infections in zebrafish.

  17. Characterization of Phenacoccus solenopsis (Tinsley) (Homoptera: Pseudococcidae) Resistance to Emamectin Benzoate: Cross-Resistance Patterns and Fitness Cost Analysis.

    Science.gov (United States)

    Afzal, M B S; Shad, S A

    2016-06-01

    Cotton mealybug Phenacoccus solenopsis (Tinsley) (Homoptera: Pseudococcidae) is a sucking pest of worldwide importance causing huge losses by feeding upon cotton in various parts of the world. Because of the importance of this pest, this research was carried out to select emamectin resistance in P. solenopsis in the laboratory to study cross-resistance, stability, realized heritability, and fitness cost of emamectin resistance. After selection from third generation (G3) to G6, P. solenopsis developed very high emamectin resistance (159.24-fold) when compared to a susceptible unselected population (Unsel pop). Population selected to emamectin benzoate conferred moderate (45.81-fold), low (14.06-fold), and no cross-resistance with abamectin, cypermethrin, and profenofos, respectively compared to the Unsel pop. A significant decline in emamectin resistance was observed in the resistant population when not exposed to emamectin from G7 to G13. The estimated realized heritability (h (2)) for emamectin resistance was 0.84. A high fitness cost was associated with emamectin resistance in P. solenopsis. Results of this study may be helpful in devising insecticide resistance management strategies for P. solenopsis.

  18. Synthesis and Biological Evaluation of 2-Hydroxy-3-[(2-aryloxyethylamino]propyl 4-[(Alkoxycarbonylamino]benzoates

    Directory of Open Access Journals (Sweden)

    Jan Tengler

    2013-01-01

    Full Text Available A series of twenty substituted 2-hydroxy-3-[(2-aryloxyethylamino]propyl 4-[(alkoxycarbonylamino]benzoates were prepared and characterized. As similar compounds have been described as potential antimycobacterials, primary in vitro screening of the synthesized carbamates was also performed against two mycobacterial species. 2-Hydroxy-3-[2-(2,6-dimethoxyphenoxyethylamino]-propyl 4-(butoxycarbonylaminobenzoate hydrochloride, 2-hydroxy-3-[2-(4-methoxyphenoxyethylamino]-propyl 4-(butoxycarbonylaminobenzoate hydrochloride, and 2-hydroxy-3-[2-(2-methoxyphenoxyethylamino]-propyl 4-(butoxycarbonylaminobenzoate hydrochloride showed higher activity against M. avium subsp. paratuberculosis and M. intracellulare than the standards ciprofloxacin, isoniazid, or pyrazinamide. Cytotoxicity assay of effective compounds was performed using the human monocytic leukaemia THP-1 cell line. Compounds with predicted amphiphilic properties were also tested for their effects on the rate of photosynthetic electron transport (PET in spinach (Spinacia oleracea L. chloroplasts. All butyl derivatives significantly stimulated the rate of PET, indicating that the compounds can induce conformational changes in thylakoid membranes resulting in an increase of their permeability and so causing uncoupling of phosphorylation from electron transport.

  19. DNA content alterations in Tetrahymena pyriformis macronucleus after exposure to food preservatives sodium nitrate and sodium benzoate.

    Science.gov (United States)

    Loutsidou, Ariadni C; Hatzi, Vasiliki I; Chasapis, C T; Terzoudi, Georgia I; Spiliopoulou, Chara A; Stefanidou, Maria E

    2012-12-01

    The toxicity, in terms of changes in the DNA content, of two food preservatives, sodium nitrate and sodium benzoate was studied on the protozoan Tetrahymena pyriformis using DNA image analysis technology. For this purpose, selected doses of both food additives were administered for 2 h to protozoa cultures and DNA image analysis of T. pyriformis nuclei was performed. The analysis was based on the measurement of the Mean Optical Density which represents the cellular DNA content. The results have shown that after exposure of the protozoan cultures to doses equivalent to ADI, a statistically significant increase in the macronuclear DNA content compared to the unexposed control samples was observed. The observed increase in the macronuclear DNA content is indicative of the stimulation of the mitotic process and the observed increase in MOD, accompanied by a stimulation of the protozoan proliferation activity is in consistence with this assumption. Since alterations at the DNA level such as DNA content and uncontrolled mitogenic stimulation have been linked with chemical carcinogenesis, the results of the present study add information on the toxicogenomic profile of the selected chemicals and may potentially lead to reconsideration of the excessive use of nitrates aiming to protect public health.

  20. Mixed-mu superconducting bearings

    Science.gov (United States)

    Hull, John R.; Mulcahy, Thomas M.

    1998-01-01

    A mixed-mu superconducting bearing including a ferrite structure disposed for rotation adjacent a stationary superconductor material structure and a stationary permanent magnet structure. The ferrite structure is levitated by said stationary permanent magnet structure.

  1. A Passive Magnetic Bearing Flywheel

    Science.gov (United States)

    Siebert, Mark; Ebihara, Ben; Jansen, Ralph; Fusaro, Robert L.; Morales, Wilfredo; Kascak, Albert; Kenny, Andrew

    2002-01-01

    A 100 percent passive magnetic bearing flywheel rig employing no active control components was designed, constructed, and tested. The suspension clothe rotor was provided by two sets of radial permanent magnetic bearings operating in the repulsive mode. The axial support was provided by jewel bearings on both ends of the rotor. The rig was successfully operated to speeds of 5500 rpm, which is 65 percent above the first critical speed of 3336 rpm. Operation was not continued beyond this point because of the excessive noise generated by the air impeller and because of inadequate containment in case of failure. Radial and axial stiffnesses of the permanent magnetic bearings were experimentally measured and then compared to finite element results. The natural damping of the rotor was measured and a damping coefficient was calculated.

  2. Bear study, Karluk Lake, 1956

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Based on observations, 117 bears were estimated to live in the Karluk Lake area. The estimate was lower than estimates from 1952, and 1954-1955. Annual loss to...

  3. Myrmecophagy by Yellowstone grizzly bears

    Science.gov (United States)

    Mattson, D.J.

    2001-01-01

    I used data collected during a study of radio-marked grizzly bears (Ursus arctos horribilis) in the Yellowstone region from 1977 to 1992 to investigate myrmecophagy by this population. Although generally not an important source of energy for the bears (averaging 8 mm long) nested in logs over small ants (6 mm long) nested under stones. Optimal conditions for consumption of ants occurred on the warmest sites with ample substrate suitable for ant nests. For ants in mounds, this occurred at low elevations at non-forested sites. For ants in logs, this occurred at low elevations or on southerly aspects where there was abundant, large-diameter, well-decomposed woody debris under an open forest canopy. Grizzly bears selected moderately decomposed logs 4a??5 dm in diameter at midpoint. Ants will likely become a more important food for Yellowstone's grizzly bears as currently important foods decline, owing to disease and warming of the regional climate.

  4. Failure analysis of superconducting bearings

    International Nuclear Information System (INIS)

    The dynamics of superconductor bearings in a cryogenic failure scenario have been analyzed. As the superconductor warms up, the rotor goes through multiple resonance frequencies, begins to slow down and finally touches down when the superconductor goes through its transition temperature. The bearing can be modelled as a system of springs with axial, radial and cross stiffness. These springs go through various resonant modes as the temperature of the superconductor begins to rise. We have presented possible explanations for such behaviour

  5. Nonlinear Control of Magnetic Bearings

    Institute of Scientific and Technical Information of China (English)

    Khac Duc Do; Dang Hoe Nguyen; Thanh Binh Nguyen

    2010-01-01

    In this paper, recent results controling nonlinear systems with output tracking error constraints are applied to the design of new tracking controllers for magnetic bearings. The proposed controllers can force the rotor to track a bounded and sufficiently smooth refer-ence trajectory asymptotically and guarantee non-contactedness be-tween the rotor and the stator of the magnetic bearings. Simulation results are included to illustrate the effectiveness of the proposed con-trollers.

  6. 77 FR 70423 - Black Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC...

    Science.gov (United States)

    2012-11-26

    ... Energy Regulatory Commission Black Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC; Notice of Application for Partial Transfer of Licenses, and Soliciting Comments and Motions To Intervene On October 25, 2012, Black Bear Hydro Partners, LLC, sole licensee (transferor)...

  7. 49 CFR 229.69 - Side bearings.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Side bearings. 229.69 Section 229.69....69 Side bearings. (a) Friction side bearings with springs designed to carry weight may not have more than 25 percent of the springs in any one nest broken. (b) Friction side bearings may not be run...

  8. 36 CFR 13.1236 - Bear orientation.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Bear orientation. 13.1236... Developed Area § 13.1236 Bear orientation. All persons visiting the BCDA must receive an NPS-approved Bear Orientation. Failure to receive an NPS-approved Bear Orientation is prohibited....

  9. Superconductor bearings, flywheels and transportation

    Science.gov (United States)

    Werfel, F. N.; Floegel-Delor, U.; Rothfeld, R.; Riedel, T.; Goebel, B.; Wippich, D.; Schirrmeister, P.

    2012-01-01

    This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS-FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN2. More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

  10. Superconductor bearings, flywheels and transportation

    International Nuclear Information System (INIS)

    This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN2. More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

  11. Future Bearing Surfaces in Total Hip Arthroplasty

    OpenAIRE

    Chang, Jun-Dong

    2014-01-01

    One of the most important issues in the modern total hip arthroplasty (THA) is the bearing surface. Extensive research on bearing surfaces is being conducted to seek an ideal bearing surface for THA. The ideal bearing surface for THA should have superior wear characteristics and should be durable, bio-inert, cost-effective, and easy to implant. However, bearing surfaces that are currently being implemented do not completely fulfill these requirements, especially for young individuals for whom...

  12. Autosizing Control Panel for Needle Bearing

    Directory of Open Access Journals (Sweden)

    Prof.A.R.Wadhekar,

    2016-02-01

    Full Text Available A needle roller bearing is a bearing which uses small cylindrical rollers. Bearings are used to reduce friction of any rotating surface. Needle bearings have a large surface in contact with the bearing outer surfaces as compared to ball bearings. There is less added clearance(Diameter of the shaft and the diameter of the bearing are different so they are much compact. The structure consists of a needle cage which contains the needle rollersthemselves and an outer race (The housing itself. Radial bearings are cylindrical and they use rollers parallel to the axis of the shaft. Radial pattern of needle are being used by thrust needles. Complement bearings have solid inner as well as outer rings and rib-guided cylindrical rollers. The bearings have the largest number of rolling elements and also have extremely high radial load carrying capacity and are suitable for compact designs.Needle roller bearings have relatively small diameter cylindrical rolling elements whose length is much larger than their diameter. As compared to other types of rolling bearings, needle roller bearings possess a small cross-sectional height and significant load-bearing capacity and rigidity relative to their volume. Also, because the inertial force acting on them is limited, needle bearings are an ideal choice for applications with oscillating motion. These bearings also work well in compact and lightweight machine designs and they serve as a ready replacement for sliding bearings. Needle bearings features are great rigidity, smaller cross-section, higher loadcarrying capacity, and has lower inertia forces that facilitate to size and weight reductions in machinery. Needle bearings are designed to stand in oscillation, performwell under any conditions, and interchange with the sliding of bearings.

  13. Sodium benzoate, a food preservative, affects the functional and activation status of splenocytes at non cytotoxic dose.

    Science.gov (United States)

    Yadav, Ashish; Kumar, Arvind; Das, Mukul; Tripathi, Anurag

    2016-02-01

    Sodium benzoate (SB) is a widely used food preservative due to its bacteriostatic and fungistatic properties. The acceptable daily intake of SB is 5 mg/kg-bw, however, it has been found to be used in the food commodities at relatively high levels (2119 mg/kg). Earlier studies on SB have shown its immunosuppressive properties, but comprehensive immunotoxicity data is lacking. Our studies have shown that SB was non cytotoxic in splenocytes up to 1000 μg/ml for 72 h, however at 2500 μg/ml it was found to be cytotoxic. Thus, 1000 μg/ml dose of SB was chosen for the subsequent experiments. SB significantly suppresses the proliferation of Con A and LPS stimulated splenocytes at 72 h, while allogenic response of T cells was significantly decreased after 96 h. SB did not affect the relative expression of CD3e or CD4 molecules following 72 h exposure, however, it downregulated the relative expression of CD8 co-receptor. Further, exposure of splenocytes to SB for 72 h led to reduced expression of CD28 and CD95, which play a vital role in T cell activation. SB also suppresses the relative expression of CD19, CD40 and CD95 receptors on B cells after 72 h. In addition to the functional responses, SB lowered the expression of IL4, IL6, IFNγ and IL17 cytokines in Con A stimulated splenocytes; and IL6, IFNγ and TNFα in LPS stimulated splenocytes following 48 h of exposure. Taken together, the present study is suggestive of the immunomodulatory potential of SB.

  14. Up-regulation of neurotrophic factors by cinnamon and its metabolite sodium benzoate: therapeutic implications for neurodegenerative disorders.

    Science.gov (United States)

    Jana, Arundhati; Modi, Khushbu K; Roy, Avik; Anderson, John A; van Breemen, Richard B; Pahan, Kalipada

    2013-06-01

    This study underlines the importance of cinnamon, a widely-used food spice and flavoring material, and its metabolite sodium benzoate (NaB), a widely-used food preservative and a FDA-approved drug against urea cycle disorders in humans, in increasing the levels of neurotrophic factors [e.g., brain-derived neurotrophic factor (BDNF) and neurotrophin-3 (NT-3)] in the CNS. NaB, but not sodium formate (NaFO), dose-dependently induced the expression of BDNF and NT-3 in primary human neurons and astrocytes. Interestingly, oral administration of ground cinnamon increased the level of NaB in serum and brain and upregulated the levels of these neurotrophic factors in vivo in mouse CNS. Accordingly, oral feeding of NaB, but not NaFO, also increased the level of these neurotrophic factors in vivo in the CNS of mice. NaB induced the activation of protein kinase A (PKA), but not protein kinase C (PKC), and H-89, an inhibitor of PKA, abrogated NaB-induced increase in neurotrophic factors. Furthermore, activation of cAMP response element binding (CREB) protein, but not NF-κB, by NaB, abrogation of NaB-induced expression of neurotrophic factors by siRNA knockdown of CREB and the recruitment of CREB and CREB-binding protein to the BDNF promoter by NaB suggest that NaB exerts its neurotrophic effect through the activation of CREB. Accordingly, cinnamon feeding also increased the activity of PKA and the level of phospho-CREB in vivo in the CNS. These results highlight a novel neutrophic property of cinnamon and its metabolite NaB via PKA - CREB pathway, which may be of benefit for various neurodegenerative disorders.

  15. DNA methylome changes by estradiol benzoate and bisphenol A links early-life environmental exposures to prostate cancer risk

    Science.gov (United States)

    Cheong, Ana; Zhang, Xiang; Cheung, Yuk-Yin; Tang, Wan-yee; Chen, Jing; Ye, Shu-Hua; Medvedovic, Mario; Leung, Yuet-Kin; Prins, Gail S.; Ho, Shuk-Mei

    2016-01-01

    ABSTRACT Developmental exposure to endocrine-disrupting chemicals (EDCs), 17β-estradiol-3-benzoate (EB) and bisphenol A (BPA), increases susceptibility to prostate cancer (PCa) in rodent models. Here, we used the methylated-CpG island recovery assay (MIRA)-assisted genomic tiling and CpG island arrays to identify treatment-associated methylome changes in the postnatal day (PND)90 dorsal prostate tissues of Sprague-Dawley rats neonatally (PND1, 3, and 5) treated with 25 µg/pup or 2,500 µg EB/kg body weight (BW) or 0.1 µg BPA/pup or 10 µg BPA/kg BW. We identified 111 EB-associated and 86 BPA-associated genes, with 20 in common, that have significant differentially methylated regions. Pathway analysis revealed cancer as the top common disease pathway. Bisulfite sequencing validated the differential methylation patterns observed by array analysis in 15 identified candidate genes. The methylation status of 7 (Pitx3, Wnt10b, Paqr4, Sox2, Chst14, Tpd52, Creb3l4) of these 15 genes exhibited an inverse correlation with gene expression in tissue samples. Cell-based assays, using 5-aza-cytidine-treated normal (NbE-1) and cancerous (AIT) rat prostate cells, added evidence of DNA methylation-mediated gene expression of 6 genes (exception: Paqr4). Functional connectivity of these genes was linked to embryonic stem cell pluripotency. Furthermore, clustering analyses using the dataset from The Cancer Genome Atlas revealed that expression of this set of 7 genes was associated with recurrence-free survival of PCa patients. In conclusion, our study reveals that gene-specific promoter methylation changes, resulting from early-life EDC exposure in the rat, may serve as predictive epigenetic biomarkers of PCa recurrence, and raises the possibility that such exposure may impact human disease. PMID:27415467

  16. EFFECT OF SODIUM BENZOATE ON THE QUALITY AND SENSORY PROPERTIES OF KUNUN-ZAKI SUPPLEMENTED WITH GROUNDNUT

    Directory of Open Access Journals (Sweden)

    Taiwo Aderinola

    2014-04-01

    Full Text Available The quality parameters of kunu-zaki supplemented with groundnut was investigated in this study. Millet, groundnut, ginger, dry red pepper and sugar were used for the production. After production, some samples were pasteurized at 700C for 30 minutes and stored at refrigerated (oC and ambient conditions (oC. A fresh control sample was also prepared at interval for comparison. Analyses were carried out to determine the chemical composition, microbiological and sensory qualities of product during storage over a period of twenty seven (27 days. Results showed that addition of groundnut improved chemical composition of the fresh samples. It could be attributed to the crude protein and the fat content in the added groundnut. The results were: moisture, 75.7%; crude protein, 13.06%; fat, 7.35%; ash, 0.39% and carbohydrate, 3.5%. The pH values for the fresh samples were: 3.31 (pasteurized refrigerated; 3.31 (pasteurized unrefrigerated; 3.57 (unpasteurized refrigerated; 3.64 (unpasteurized unrefrigerated and 3.93 for the Fresh sample. The results of the mineral element (mg/100g were: Ca, 152; Na, 0.19; Mg, 4.76; K, 2.74 and P, 123.22. There was no detection of the presence of the indicator organism – E coli. Results of the sensory evaluation of the product carried out using a five-man panel showed that there were no differences in the appearance, taste and flavor for the first day. However, the pasteurized refrigerated sample with the addition of sodium benzoate was better on the overall acceptability.

  17. Safety and determination benzoic acid and sodium benzoate%苯甲酸和苯甲酸钠安全性与检测方法研究进展

    Institute of Scientific and Technical Information of China (English)

    李菊; 刘淑君; 黄雪琳

    2012-01-01

      As one of the acidic preservative,the abuse of benzoic acid and sodium benzoate is very dangerous. Because the residue of benzoic acid and sodium benzoate would do great harm to the human health even cause cancer after they were taken through the food and medicament. The researchers have dedicated many efforts to research for residue determination of benzoic acid and Sodium Benzoate. The security and methods for benzoic acid and sodium benzoate detection were summarized. this study was useful for the detecting technology of benzoic acid and sodium benzoate residues.%  苯甲酸和苯甲酸钠是一种酸性防腐剂,过量滥用很危险;因苯甲酸和苯甲酸钠被人体过量摄入后,会对人体健康造成极大危害,甚至致癌。该文对苯甲酸和苯甲酸钠残留安全性及检测方法进行综述,以期为苯甲酸和苯甲酸钠残留检测方法研究提供参考。

  18. The Bear That Isn't a Bear

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    Koalas aren't bears.They belong to the same family as kangaroos.Animals of this family are called pouch animals.That's because the mother carries her baby around in a pouch in the front of her stomach.lt's like a built-in papoose basket, only it's in the front instead of the back.

  19. 超声法制备苯甲酸钠微胶囊的工艺研究%Research on Processing Technology of Sodium Benzoate Microcapsules by Ultrasound

    Institute of Scientific and Technical Information of China (English)

    章斌; 刘志聪; 侯小桢; 赖宣; 许淼鑫; 王士超

    2014-01-01

    以β-环糊精为壁材,以包埋率为指标,采用单因素试验和Box-Behnken 中心组合设计试验对超声法制备苯甲酸钠微胶囊的工艺进行优化。试验结果表明:超声法制备苯甲酸钠包合物的最佳工艺条件为芯/壁材比1∶7.17,超声包埋时间29.9 min,超声包埋功率180 W,此条件下的实际包埋率为80.5%,与模型预测值之间具有较好的拟合性。%Takeβ-cyclodextrin as wall material and embedding rate of sodium benzoate as main index, the single factor experiment and Box-Behnken response surface methodology for optimization of sodi-um benzoate microcapsules by ultrasound method is explored.The results show that the optimum process conditions for preparation of sodium benzoate clathrate by ultrasound method are as follows:the core/wall material ratio of 1∶7.17,the ultrasonic embedding time of 29.9 min,the ultrasonic embedding power of 180 W,the embedding rate can reach 80.5%,and the regression model is con-sistent with the predicted results.

  20. The reproductive performance of dairy cows with anovulatory anoestrus that were injected with either gonadotrophin-releasing hormone or oestradiol benzoate as part of a re-treatment process after insemination

    Directory of Open Access Journals (Sweden)

    B.V.E. Segwagwe

    2007-05-01

    Full Text Available This experiment compared the reproductive performance of synchronised anoestrous dairy cows that were treated initially with a combination of progesterone and oestradiol benzoate and then with either gonadotrophin-releasing hormone (GnRH or oestradiol benzoate to resynchronise returns to service. It was hypothesised that injecting anoestrous dairy cows with GnRH 12-15 days after insemination and coinciding with the time of insertion of a controlled intravaginal progesterone-releasing (CIDR device would increase conception rates to the preceding 1st insemination compared with oestradiol benzoate treated cows; both GnRH and oestradiol benzoate would resynchronising the returns to service of those cows that did not conceive to the preceding insemination. Groups of cows in 11 herds were presented for a veterinary examination after they had not been seen in oestrus postpartum. Those cows diagnosed with anovulatory anoestrus (n = 1112 by manual rectal palpation and / or ultrasonography were enrolled in the trial. Each enrolled cow was injected with 2mg oestradiol benzoate i.m. on Day -10, (where Day 0 was the 1st day of the planned insemination concurrently with vaginal insertion of a CIDR device. The device inserted was withdrawn on Day -2 and then each cow injected i.m. with 1 mg of oestradiol benzoate on Day -1 unless it was in oestrus. Observation for oestrus preceded each insemination. Every cow that had been inseminated on Days -1,0,1 or 2 was presented for treatment for resynchrony on Day 14 (n=891. They were divided into 2 groups; those with an even number were each injected i.m. with 250 µg of a GnRH agonist (Treatment group n = 477; each of the cows with an odd number injected i.m. with 1mg of oestradiol benzoate (control group, n = 414. Each GnRH or oestradiol benzoate injection preceded reinsertion of a CIDR device previously inserted from Days -10 to -2. It was withdrawn on Day 22, 24 hours before injecting 1mg oestradiol benzoate

  1. The correct "ball bearings" data.

    Science.gov (United States)

    Caroni, C

    2002-12-01

    The famous data on fatigue failure times of ball bearings have been quoted incorrectly from Lieblein and Zelen's original paper. The correct data include censored values, as well as non-fatigue failures that must be handled appropriately. They could be described by a mixture of Weibull distributions, corresponding to different modes of failure.

  2. EFFECT OF CLEARANCE THE BALL BEARINGS ON INCORRECT WORK OF THREE-SUPORT BEARING SHAFT

    Directory of Open Access Journals (Sweden)

    Jarosław KACZOR

    2014-06-01

    Full Text Available Durability deep groove ball bearings depends on factors (called attributes design, technological and operational. Among the design features one of the most important is play in the bearings. Polish Norm shows five groups of looseness in the bearings, in which the play range from 0 to 105 microns. Manufacturers of rolling bearings they only play group, which has a bearing data, without giving the exact value of the slack. Aim of this study is to determine how it affects the play in the bearings to work three-bearing shafts, including elasticity and resilience three-bearing shafts.

  3. Journal and Wave Bearing Impedance Calculation Software

    Science.gov (United States)

    Hanford, Amanda; Campbell, Robert

    2012-01-01

    The wave bearing software suite is a MALTA application that computes bearing properties for user-specified wave bearing conditions, as well as plain journal bearings. Wave bearings are fluid film journal bearings with multi-lobed wave patterns around the circumference of the bearing surface. In this software suite, the dynamic coefficients are outputted in a way for easy implementation in a finite element model used in rotor dynamics analysis. The software has a graphical user interface (GUI) for inputting bearing geometry parameters, and uses MATLAB s structure interface for ease of interpreting data. This innovation was developed to provide the stiffness and damping components of wave bearing impedances. The computational method for computing bearing coefficients was originally designed for plain journal bearings and tilting pad bearings. Modifications to include a wave bearing profile consisted of changing the film thickness profile given by an equation, and writing an algorithm to locate the integration limits for each fluid region. Careful consideration was needed to implement the correct integration limits while computing the dynamic coefficients, depending on the form of the input/output variables specified in the algorithm.

  4. Mobile bearing and fixed bearing total knee arthroplasty

    Science.gov (United States)

    Dolfin, Marco; Saccia, Francesco

    2016-01-01

    The mobile bearing (MB) concept in total knee arthroplasty (TKA) was developed as an alternative to fixed bearing (FB) implants in order to reduce wear and improve range of motion (ROM), especially focused on younger patients. Unfortunately, its theoretical advantages are still controversial. In this paper we exhibit a review of the more recent literature available comparing FB and MB designs in biomechanical and clinical aspects, including observational studies, clinical trials, national and international registries analyses, randomized controlled trials, meta-analyses and Cochrane reviews. Except for some minor aspects, none of the studies published so far has reported a significant improvement related to MBs regarding patient satisfaction, clinical, functional and radiological outcome or medium and long-term survivorship. Thus the presumed superiority of MBs over FBs appears largely inconsistent. The routine use of MB is not currently supported by adequate evidences; implant choice should be therefore made on the basis of other factors, including cost and surgeon experience. PMID:27162777

  5. Mobile bearing and fixed bearing total knee arthroplasty.

    Science.gov (United States)

    Capella, Marcello; Dolfin, Marco; Saccia, Francesco

    2016-04-01

    The mobile bearing (MB) concept in total knee arthroplasty (TKA) was developed as an alternative to fixed bearing (FB) implants in order to reduce wear and improve range of motion (ROM), especially focused on younger patients. Unfortunately, its theoretical advantages are still controversial. In this paper we exhibit a review of the more recent literature available comparing FB and MB designs in biomechanical and clinical aspects, including observational studies, clinical trials, national and international registries analyses, randomized controlled trials, meta-analyses and Cochrane reviews. Except for some minor aspects, none of the studies published so far has reported a significant improvement related to MBs regarding patient satisfaction, clinical, functional and radiological outcome or medium and long-term survivorship. Thus the presumed superiority of MBs over FBs appears largely inconsistent. The routine use of MB is not currently supported by adequate evidences; implant choice should be therefore made on the basis of other factors, including cost and surgeon experience. PMID:27162777

  6. Effects of bearing deadbands on bearing loads and rotor stability

    Science.gov (United States)

    1984-01-01

    A generic model of a turbopump, simplified to bring out these effects is examined. This model demonstrates that bearing deadbands which are of the same order of magnitude or larger than the center-of-mass offset of a rotor due to mass imbalances cause significantly different dynamic behavior than would be expected of a linear, dynamical system. This fundamentally nonlinear behavior yields altered stability characteristics and altered bearing loading tendencies. It is shown that side forces can enhance system stability in the small, i.e., as long as the mass imbalance does not exceed some thresholds value or as long as no large, impulsive disturbances cause the motion to depart significantly from the region of stability. Limit cycles are investigated in this report and techniques for determining these limit cycles are developed. These limit cycles are the major source of bearing loading and appear in both synchronous and nonsynchronous forms. The synchronous limit cycles are driven by rotor imbalances. The nonsynchronous limit cycles (also called subsynchronous whirls) are self-excited and are the sources of instability.

  7. Microbial evolution during storage of seasoned olives prepared with organic acids with potassium sorbate, sodium benzoate, and ozone used as preservatives.

    Science.gov (United States)

    Arroyo López, F N; Durán Quintana, M C; Garrido Fernández, A

    2006-06-01

    The effect of potassium sorbate, sodium benzoate, and ozone in combination with citric, lactic, and acetic acids on the microbial population of seasoned table olives of the olive 'Aloreña' cultivar was studied in both fresh (FF) and stored fruits (SF). The inactivation/growth curves were modeled and the biological parameters estimated, with yeast used as the target microorganism. Regardless of the acid added, potassium sorbate showed a general inactivation effect on yeasts in the products prepared from both FF and SE Sodium benzoate had a rapid inactivation effect with FF, but with SF, it was effective only in the presence of acetic acid. A strain of Issatchenkia occidentalis was found that was resistant to the combination of this preservative with citric or lactic acids. In FF, ozone showed an initial marked inhibition against yeasts, but later, yeasts were again able to grow. In SF, ozone was a strong inactivating agent when it replaced any of the traditional preservatives. Lactic acid bacteria were always absent in products prepared from FF, and apparently were not affected by the different preservative agents in those prepared from SF. The behavior of yeasts and lactic acid bacteria populations in commercial products were similar to those found in experimental treatments.

  8. Evaluation of Agrilus planipennis (Coleoptera: Buprestidae) control provided by emamectin benzoate and two neonicotinoid insecticides, one and two seasons after treatment.

    Science.gov (United States)

    McCullough, Deborah G; Poland, Therese M; Anulewicz, Andrea C; Lewis, Phillip; Cappaert, David

    2011-10-01

    Effective methods are needed to protect ash trees (Fraxinus spp.) from emerald ash borer, Agrilus planipennis Fairmaire (Coleoptera: Buprestidae), an invasive buprestid that has killed millions of North American ash (Fraxinus spp.) trees. We randomly assigned 175 ash trees (11.5-48.1 cm in diameter) in 25 blocks located in three study sites in Michigan to one of seven insecticide treatments in May 2007. Treatments included 1) trunk-injected emamectin benzoate; 2) trunk-injected imidacloprid; 3) basal trunk spray of dinotefuran with or 4) without Pentra-Bark, an agricultural surfactant; 5) basal trunk spray of imidacloprid with or 6) without Pentra-Bark; or (7) control. Foliar insecticide residues (enzyme-linked immunosorbent assay) and toxicity of leaves to adult A. planipennis (4-d bioassays) were quantified at 3-4-wk intervals posttreatment. Seven blocks of trees were felled and sampled in fall 2007 to quantify A. planipennis larval density. Half of the remaining blocks were retreated in spring 2008. Bioassays and residue analyses were repeated in summer 2008, and then all trees were sampled to assess larval density in winter. Foliage from emamectin benzoate-treated trees was highly toxic to adult A. planipennis, and larval density was or = 2 yr may reduce costs or logistical issues associated with treatment. PMID:22066190

  9. Estudio de las Propiedades Anticorrosivas del Benzoato de Hierro (III en Pinturas Base Solvente Study of Anticorrosive Properties of the Iron (III Benzoate in Solvent Based Paints

    Directory of Open Access Journals (Sweden)

    Guillermo Blustein

    2006-01-01

    Full Text Available La acción inhibidora del benzoato de hierro en electrodos de acero SAE 1010 en contacto con una suspensión acuosa fue estudiada mediante ensayos electroquímicos. Paralelamente, la eficiencia anticorrosiva de este producto incorporado a cubiertas orgánicas base solvente fue evaluada mediante ensayos de envejecimiento acelerado (cámara de niebla salina y de humedad. La evolución del comportamiento protector de la cubierta aplicada sobre paneles de acero pintados e inmersos en una solución 0.5M de NaClO4 fue periódicamente monitoreada por espectroscopía de impedancia electroquímica. Los resultados obtenidos indican que las pinturas formuladas con benzoato férrico presentan una capacidad anticorrosiva comparable a las formuladas con fosfato de cinc.This study investigated the inhibitory action of iron benzoate on SAE 1010 steel electrodes in aqueous suspensions using electrochemical assays. The anticorrosive efficiency of this product added to organic solvent-based coatings was also evaluated by means of accelerated weathering tests (salt spray cabinet and humidity chamber. The evolution of the protective behavior of the coating applied on steel panels and immersed in 0.5M NaClO4 solution was periodically checked by electrochemical impedance spectroscopy. The results obtained showed that paints formulated with ferric benzoate provide anticorrosive protection similar to those formulated with zinc phosphate.

  10. Fixation of chiral smectic liquid crystal (S)-(+)-4-(2-methyl-1-butyloyloxy)phenyl 4-[1-(propenoyloxy) butiloxy] benzoate using UV curing techniques

    Energy Technology Data Exchange (ETDEWEB)

    Afrizal,, E-mail: rizalunj04@yahoo.com; Nurdelima,; Umeir [Faculty of Mathemathics and Natural Science, University of State Jakarta, Jakarta (Indonesia); Hikam, Muhammad; Soegiyono, Bambang [Department of Materials Science, University of Indonesia, Depok (Indonesia); Riswoko, Asep [Center for Material Technology, BPPT, Jl. MH.Thamrin 8 Jakarta (Indonesia)

    2014-03-24

    Chiral Smectic Liquid Crystal (S)-(+)-4-(2-methyl-1-butyloyloxy)phenyl 4-[1-(propenoyloxy) butiloxy] benzoate has been synthesized using method of steglich esterification at room temperature. The mesomorphic behavior of chiral smectic at 55°C that showed schlieren texture in POM analysis. Fixation of structure chiral smectic liquid crystal by means of photopolymerization of monomer (S)-(+)-4-(2-methyl-1-butyloyloxy)phenyl 4-[1-(propenoyloxy) butiloxy] benzoate under UV irradiation which called UV curing techniques. The curing process using UV 3 lamps 100 volt at 60°C for an hour. The product of photopolymerization could be seen by analysis of FTIR spectra both monomer and polymer. FTIR spectra of monomer, two peaks for ester carbonyl and C-C double bond groups appeared at 1729.09 cm-1and 3123.46 cm{sup −1}. After UV curing process, peak for the carbonyl group at 1729.09 cm{sup −1} decreased and a new peak at 1160.21 cm{sup −1} appeared due to the carbonyl group attached to a C-C bond group and then peak at 3123.46 cm{sup −1} for C-C double bond group was disappeared.

  11. Live-trapping and handling brown bear

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This paper reports techniques developed to live trap and handle brown bears on the Kodiak National Wildlife Refuge. The brown bears (Ursus middendorffi) on the...

  12. Goose Eggs Could Save Polar Bears

    Institute of Scientific and Technical Information of China (English)

    孙淑敏

    2009-01-01

    Polar bears could avoid extinction despitemany starving to death in coming years, ac-cording to scientists and other observers whohave discovered that some of the bears havefound a new food source--goose and duckeggs.

  13. Rolling Element Bearing Stiffness Matrix Determination (Presentation)

    Energy Technology Data Exchange (ETDEWEB)

    Guo, Y.; Parker, R.

    2014-01-01

    Current theoretical bearing models differ in their stiffness estimates because of different model assumptions. In this study, a finite element/contact mechanics model is developed for rolling element bearings with the focus of obtaining accurate bearing stiffness for a wide range of bearing types and parameters. A combined surface integral and finite element method is used to solve for the contact mechanics between the rolling elements and races. This model captures the time-dependent characteristics of the bearing contact due to the orbital motion of the rolling elements. A numerical method is developed to determine the full bearing stiffness matrix corresponding to two radial, one axial, and two angular coordinates; the rotation about the shaft axis is free by design. This proposed stiffness determination method is validated against experiments in the literature and compared to existing analytical models and widely used advanced computational methods. The fully-populated stiffness matrix demonstrates the coupling between bearing radial, axial, and tilting bearing deflections.

  14. Shaft Center Orbit in Dynamically Loaded Bearings

    DEFF Research Database (Denmark)

    Klit, Peder

    The aim of this work is to demonstrate how to utilize the bearings damping coefficients to estimate the orbit for a dynamically loaded journal bearing. The classical method for this analysis was developed by Booker in 1965 and described further in 1972. Several authors have refined this method over...... the years. In 1966 Jorgen W. Lund published an approach to find the dynamic coefficients of a journal bearing by a first order perturbation of the Reynold's equation. These coefficients made it possible to perform a rotor-bearing stability analysis for a statically loaded bearing. In the mid seventies...... Jorgen W. Lund pointed out in lecture notes that the dynamic damping coefficients of the bearing could be used to find the shaft orbit for dynamically loaded bearings. For simplicity the "Short-Width-Journal-Bearing Theory" is used as a basis for finding the damping coefficients in this work...

  15. Brown bear telemetry and trapping: Special report

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Brown bear studies were continued during the 1967 field season with emphasis on development of techniques for instrumenting bears with radio transmitters and...

  16. Stable isotopes to detect food-conditioned bears and to evaluate human-bear management

    Science.gov (United States)

    Hopkins, John B.; Koch, Paul L.; Schwartz, Charles C.; Ferguson, Jake M.; Greenleaf, Schuyler S.; Kalinowski, Steven T.

    2012-01-01

    We used genetic and stable isotope analysis of hair from free-ranging black bears (Ursus americanus) in Yosemite National Park, California, USA to: 1) identify bears that consume human food, 2) estimate the diets of these bears, and 3) evaluate the Yosemite human–bear management program. Specifically, we analyzed the isotopic composition of hair from bears known a priori to be food-conditioned or non-food-conditioned and used these data to predict whether bears with an unknown management status were food-conditioned (FC) or non-food-conditioned (NFC). We used a stable isotope mixing model to estimate the proportional contribution of natural foods (plants and animals) versus human food in the diets of FC bears. We then used results from both analyses to evaluate proactive (population-level) and reactive (individual-level) human–bear management, and discussed new metrics to evaluate the overall human–bear management program in Yosemite. Our results indicated that 19 out of 145 (13%) unknown bears sampled from 2005 to 2007 were food-conditioned. The proportion of human food in the diets of known FC bears likely declined from 2001–2003 to 2005–2007, suggesting proactive management was successful in reducing the amount of human food available to bears. In contrast, reactive management was not successful in changing the management status of known FC bears to NFC bears, or in reducing the contribution of human food to the diets of FC bears. Nine known FC bears were recaptured on 14 occasions from 2001 to 2007; all bears were classified as FC during subsequent recaptures, and human–bear management did not reduce the amount of human food in the diets of FC bears. Based on our results, we suggest Yosemite continue implementing proactive human–bear management, reevaluate reactive management, and consider removing problem bears (those involved in repeated bear incidents) from the population.

  17. Oil film pressure in hydrodynamic journal bearings

    OpenAIRE

    Valkonen, Antti

    2009-01-01

    Hydrodynamic journal bearings are critical power transmission components that are carrying increasingly high loads because of the increasing power density in various machines. Therefore, knowing the true operating conditions of hydrodynamic journal bearings is essential to machine design. Oil film pressure is one of the key operating parameters describing the operating conditions in hydrodynamic journal bearings. Measuring the oil film pressure in bearings has been a demanding task and theref...

  18. Technology development for indigenous water lubricated bearings

    International Nuclear Information System (INIS)

    Water Lubricated Bearings (WLB) are used in various mechanisms of fuel handling systems of PHWRs and AHWR. Availability and random failures of these bearings was a major factor in refuelling operations. Indigenous development of these bearings was taken up and 7 types of antifriction bearings in various sizes (totaling 37 variants) for PHWR, AHWR and Dhruva applications were successfully developed. This paper deals with various aspects of WLB development. (author)

  19. Thin film superconductor magnetic bearings

    Science.gov (United States)

    Weinberger, Bernard R.

    1995-12-26

    A superconductor magnetic bearing includes a shaft (10) that is subject to a load (L) and rotatable around an axis of rotation, a magnet (12) mounted to the shaft, and a stator (14) in proximity to the shaft. The stator (14) has a superconductor thin film assembly (16) positioned to interact with the magnet (12) to produce a levitation force on the shaft (10) that supports the load (L). The thin film assembly (16) includes at least two superconductor thin films (18) and at least one substrate (20). Each thin film (18) is positioned on a substrate (20) and all the thin films are positioned such that an applied magnetic field from the magnet (12) passes through all the thin films. A similar bearing in which the thin film assembly (16) is mounted on the shaft (10) and the magnet (12) is part of the stator (14) also can be constructed.

  20. 49 CFR 229.64 - Plain bearings.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Plain bearings. 229.64 Section 229.64 Transportation Other Regulations Relating to Transportation (Continued) FEDERAL RAILROAD ADMINISTRATION....64 Plain bearings. A plain bearing box shall contain visible free oil and may not be cracked to...

  1. Passive Thermal Management of Foil Bearings

    Science.gov (United States)

    Bruckner, Robert J. (Inventor)

    2015-01-01

    Systems and methods for passive thermal management of foil bearing systems are disclosed herein. The flow of the hydrodynamic film across the surface of bearing compliant foils may be disrupted to provide passive cooling and to improve the performance and reliability of the foil bearing system.

  2. 14 CFR 27.623 - Bearing factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bearing factors. 27.623 Section 27.623... STANDARDS: NORMAL CATEGORY ROTORCRAFT Design and Construction General § 27.623 Bearing factors. (a) Except... subject to pounding or vibration, must have a bearing factor large enough to provide for the effects...

  3. 14 CFR 23.623 - Bearing factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bearing factors. 23.623 Section 23.623... Bearing factors. (a) Each part that has clearance (free fit), and that is subject to pounding or vibration, must have a bearing factor large enough to provide for the effects of normal relative motion. (b)...

  4. 14 CFR 25.623 - Bearing factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bearing factors. 25.623 Section 25.623... STANDARDS: TRANSPORT CATEGORY AIRPLANES Design and Construction General § 25.623 Bearing factors. (a) Except... subject to pounding or vibration, must have a bearing factor large enough to provide for the effects...

  5. 14 CFR 29.623 - Bearing factors.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Bearing factors. 29.623 Section 29.623... STANDARDS: TRANSPORT CATEGORY ROTORCRAFT Design and Construction General § 29.623 Bearing factors. (a... subject to pounding or vibration, must have a bearing factor large enough to provide for the effects...

  6. Cool Polar Bears: Dabbing on the Texture

    Science.gov (United States)

    O'Connell, Jean

    2011-01-01

    In this article, the author describes how her second-graders created their cool polar bears. The students used the elements of shape and texture to create the bears. They used Monet's technique of dabbing paint so as to give the bear some texture on his fur.

  7. Fractal analysis of polar bear hairs

    Directory of Open Access Journals (Sweden)

    Wang Qing-Li

    2015-01-01

    Full Text Available Hairs of a polar bear (Ursus maritimus are of superior properties such as the excellent thermal protection. Why do polar bears can resist such cold environment? The paper concludes that its fractal porosity plays an important role, and its fractal dimensions are very close to the golden mean, 1.618, revealing the possible optimal structure of polar bear hair.

  8. Elid superfinishing of spherical bearings

    OpenAIRE

    Raffles, Mark H.

    2007-01-01

    Driven by a requirement to extend the lifespan of self-aligning lined spherical bearings, this research investigates the use of Elid (electrolytic in-process dressing) as a method of improving ball surface finish. Elid is a continuous and self-regulating electrochemical dressing process that modifies the surface of a grinding, lapping, or superfinishing wheel. It provides improved grit protrusion, impedes wheel loading / glazing and promotes effective cutting. The characteri...

  9. Risk-bearing and Entrepreneurship

    OpenAIRE

    Newman, Andrew

    2007-01-01

    In the 'Knightian' theory of entrepreneurship, entrepreneurs provide insurance to workers by paying fixed wages and bear all the risk of production. This paper endogenizes entrepreneurial risk by allowing for optimal insurance contracts as well as the occupational self-selection. Moral hazard prevents full insurance; increases in an agent’s wealth then entail increases in risk borne. Thus, even under decreasing risk aversion, there are robust instances in which workers are wealthier than entr...

  10. Microstructural degradation of bearing steels

    OpenAIRE

    Solano Alvarez, Wilberth

    2015-01-01

    The aim of the work presented in this thesis is to clarify one of the most fundamental aspects of fatigue damage in bearings steels through critical experiments, in particular whether damage in the form of cracks precedes hard ?white-etching matter" formation, which is carbon supersaturated nanoscaled ferrite. Heat treatments have been designed to create four different crack types and distributions: scarce martensite plate cracks, fine grain boundary cracks, abundant martensite plate cracks, ...

  11. EFFECT OF PRELOAD OF ANGULAR CONTACT BALL BEARINGS ON LIFE OF BEARINGS

    OpenAIRE

    Andrzej RACZYŃSKI; Jarosław KACZOR

    2014-01-01

    Angular contact ball bearings are commonly used in such situations when you need to reach high bearing stiffness. However, a significant stiffness increase can be achieved only through the introduction of preload to the angular contact bearings. The purpose of this paper is to present a method for assessing the effect of preload of the angular contact bearings for their durability.

  12. EFFECT OF PRELOAD OF ANGULAR CONTACT BALL BEARINGS ON LIFE OF BEARINGS

    Directory of Open Access Journals (Sweden)

    Andrzej RACZYŃSKI

    2014-06-01

    Full Text Available Angular contact ball bearings are commonly used in such situations when you need to reach high bearing stiffness. However, a significant stiffness increase can be achieved only through the introduction of preload to the angular contact bearings. The purpose of this paper is to present a method for assessing the effect of preload of the angular contact bearings for their durability.

  13. Cannibalism and predation on black bears by grizzly bears in the Yellowstone ecosystem, 1975-1990

    Science.gov (United States)

    Mattson, D.J.; Knight, R.R.; Blanchard, B.M.

    1992-01-01

    We documented one instance of an adult male grizzly bear preying upon a black bear and four instances where circumstantial evidence suggested that grizzly bears (two cubs-of-the-year, one yearling female that was injured, and one adult male) had been preyed upon by conspecifics. We also examined feces of grizzly bears for bear remains. Remains of bears tended to be more common in spring feces and did not differ in frequency between early and late years of the study. Our observations generally support existing hypotheses concerning cannibalism among bears.

  14. Improvement of journal bearing operation at heavy misalignment using bearing flexibility and compliant liners

    DEFF Research Database (Denmark)

    Thomsen, Kim; Klit, Peder

    2012-01-01

    A flexure journal bearing design is proposed that will improve operational behaviour of a journal bearing at pronounced misalignment. Using a thermoelastohydrodynamic model, it is shown that the proposed flexure journal bearing has vastly increased the hydrodynamic performance compared to the stiff...... bearing when misaligned. The hydrodynamic performance is evaluated on lubricant film thickness, pressure and temperature. Furthermore, the influence of a compliant bearing liner is investigated and it is found that it increases the hydrodynamic performance when applied to a stiff bearing, whereas...... the liner has practically no influence on the flexure journal bearing's performance....

  15. Ball Bearing Stacking Automation System

    Directory of Open Access Journals (Sweden)

    Shafeequerrahman S . Ahmed

    2013-01-01

    Full Text Available This document is an effort to introduce the concept of automation in small scale industries and or small workshops that are involved in the manufacturing of small objects such as nuts, bolts and ball bearing in this case. This an electromechanical system which includes certain mechanical parts that involves one base stand on which one vertical metallic frame is mounted and hinged to this vertical stand is an in humanized effort seems inadequate in this era making necessary the use of Electronics, Computer in the manufacturing processes leading to the concept of Automated Manufacturing System (AMS.The ball bearing stack automation is an effort in this regard. In our project we go for stack automation for any object for example a ball bearing, be that is still a manual system there. It will be microcontroller based project control system equipped with microcontroller 89C51 from any manufacturer like Atmel or Philips. This could have been easily implemented if a PLC could be used for manufacturing the staking unit but I adopted the microcontroller based system so that some more modification in the system can be effected at will as to use the same hardware .Although a very small object i.e. ball bearig or small nut and fixture will be tried to be stacked, the system with more precision and more power handling capacity could be built for various requirements of the industry. For increasing more control capacity, we can use another module of this series. When the bearing is ready, it will be sent for packing. This is sensed by an inductive sensor. The output will be proceeds by PLC and microcontroller card which will be driving the assembly in order to put it into pads or flaps. This project will also count the total number of bearings to be packed and will display it on a LCD for real time reference and a provision is made using a higher level language using hyper terminal of the computer

  16. Valve assembly having remotely replaceable bearings

    Science.gov (United States)

    Johnson, Evan R.; Tanner, David E.

    1980-01-01

    A valve assembly having remotely replaceable bearings is disclosed wherein a valve disc is supported within a flow duct for rotation about a pair of axially aligned bearings, one of which is carried by a spindle received within a diametral bore in the valve disc, and the other of which is carried by a bearing support block releasably mounted on the duct circumferentially of an annular collar on the valve disc coaxial with its diametrical bore. The spindle and bearing support block are adapted for remote removal to facilitate servicing or replacement of the valve disc support bearings.

  17. Heuristic explanation of journal bearing instability

    Science.gov (United States)

    Crandall, S. H.

    1982-01-01

    A fluid-filled journal bearing is viewed as a powerful pump circulating fluid around the annular space between the journal and the bearing. A small whirling motion of the journal generates a wave of thickness variation progressing around the channel. The hypothesis that the fluid flow drives the whirl whenever the mean of the pumped fluid velocity is greater than the peripheral speed of the thickness variation wave is discussed and compared with other simple explanations of journal bearing instability. It is shown that for non-cavitation long bearings the hypothesis predicts instability onset correctly for unloaded bearings but gradually overpredicts the onset speed as the load is increased.

  18. Ball Bearing Analysis with the ORBIS Tool

    Science.gov (United States)

    Halpin, Jacob D.

    2016-01-01

    Ball bearing design is critical to the success of aerospace mechanisms. Key bearing performance parameters, such as load capability, stiffness, torque, and life all depend on accurate determination of the internal load distribution. Hence, a good analytical bearing tool that provides both comprehensive capabilities and reliable results becomes a significant asset to the engineer. This paper introduces the ORBIS bearing tool. A discussion of key modeling assumptions and a technical overview is provided. Numerous validation studies and case studies using the ORBIS tool are presented. All results suggest the ORBIS code closely correlates to predictions on bearing internal load distributions, stiffness, deflection and stresses.

  19. Coupled Dynamics of a Rotor-Journal Bearing System Equipped with Thrust Bearings

    OpenAIRE

    Yu Lie; R.B. Bhat

    1995-01-01

    The rotordynamic coefficients of fixed-pad thrust bearing are introduced and calculated by using the out-domain method, and a general analysis method is developed to investigate the coupled dynamics of a rotor equipped with journal and thrust bearings simultaneously. Considerations include the effects of static tilt parameters of the rotor on rotordynamic coefficients of thrust bearing and the action of thrust bearing on system dynamics. It is shown that thrust bearing changes the load distri...

  20. HPLC and LC-MS/MS methods for determination of sodium benzoate and potassium sorbate in food and beverages: performances of local accredited laboratories via proficiency tests in Turkey.

    Science.gov (United States)

    Gören, Ahmet C; Bilsel, Gökhan; Şimşek, Adnan; Bilsel, Mine; Akçadağ, Fatma; Topal, Kevser; Ozgen, Hasan

    2015-05-15

    High Performance Liquid Chromatography LC-UV and LC-MS/MS methods were developed and validated for quantitative analyses of sodium benzoate and potassium sorbate in foods and beverages. HPLC-UV and LC-MS/MS methods were compared for quantitative analyses of sodium benzoate and potassium sorbate in a representative ketchup sample. Optimisation of the methods enabled the chromatographic separation of the analytes in less than 4 min. A correlation coefficient of 0.999 was achieved over the measured calibration range for both compounds and methods (HPLC and LC-MS/MS). The uncertainty values of sodium benzoate and potassium sorbate were found as 0.199 and 0.150 mg/L by HPLC and 0.072 and 0.044 mg/L by LC-MS/MS, respectively. Proficiency testing performance of Turkish accredited laboratories between the years 2005 and 2013 was evaluated and reported herein. The aim of the proficiency testing scheme was to evaluate the performance of the laboratories, analysing benzoate and sorbate in tomato ketchup. PMID:25577080

  1. Design, synthesis and in vitro antibacterial activities of methyl-4-((substituted phenyl) [6H-indolo (2,3-b)quinoxalin-6-yl]methyl-amino)benzoate derivatives

    Institute of Scientific and Technical Information of China (English)

    Yellajyosula Lakshmi Narasimha Murthy; Nagalakshmi Karthikeyan; Govindh Boddeti; Bhagavathula S. Diwakar; E. Rajendra Singh

    2011-01-01

    A series of new methyl-4-((substituted phenyl) [6H-indolo (2,3-b)quinoxalin-6yllmethylamino)benzoate derivatives have been synthesized and assayed for their antibacterial activity on 9 different bacterial strains. Among the screened compounds 2e-2g exhibited potent inhibitory activity compared to standard drug employed, worth further investigation.

  2. A prototype construction of bearing heater system

    International Nuclear Information System (INIS)

    A bearing heater system has been successfully constructed using transformer-like method of 1000 VA power, 220 V primary voltage, and 50 Hz electrical frequency. The bearing heater consists of primary coil 230 turns, U type and bar-type iron core with 36 cm2, 9 cm2 ,and 3 cm2 cross-section, and electrical isolation. The bearing heater is used to enlarge the diameter of the bearing so that it can be easily fixed on an electric motor shaft during replacement because the heating is conducted by treated the bearing as a secondary coil of a transformer. This bearing heater can be used for bearing with 3 and 6 cm of inner diameter and 12 cm of maximum outside diameter. (author)

  3. Pratt and Whitney cryogenic turbopump bearing experience

    Science.gov (United States)

    Poole, W. E.; Bursey, R. W., Jr.

    1988-01-01

    Successful, reusable bearings require lubrication, traditionally, a transfer film from sacrificial cage wear. Early testing included materials screening programs to identify suitable cryogenic cage materials. A specially developed element tester that simulated the function of a ball bearing cage was used. Suitable materials must provide lubrication with an acceptably low wear rate, without abrading contacting surfaces. The most promising materials were tested in full scale bearings at speeds up to 4 MDN. Teflon, filled with 40 percent bronze powder, was the best performing material. A variety of bearings were designed and successfully tested in LH2 and LOX. Bearings with bronze filled Teflon cages were successfully tested for 150 hrs. In overload tests, the same design was tested for 5 hrs at maximum Hertz stresses above 450 ksi and an additional 5 hrs with a maximum Hertz stress exceeding 500 ksi. Four bearings were tested in LOX for 25 hrs, with a maximum time per bearing of 10 hrs.

  4. Wave Journal Bearings Under Dynamic Loads

    Science.gov (United States)

    Hendricks, Robert C.; Dimofte, Florin

    2002-01-01

    The dynamic behavior of the wave journal bearing was determined by running a three-wave bearing with an eccentrically mounted shaft. A transient analysis was developed and used to predict numerical data for the experimental cases. The three-wave journal bearing ran stably under dynamic loads with orbits well inside the bearing clearance. The orbits were almost circular and nearly free of the influence of, but dynamically dependent on, bearing wave shape. Experimental observations for both the absolute bearing-housing-center orbits and the relative bearing-housing-center-to-shaft-center orbits agreed well with the predictions. Moreover, the subsynchronous whirl motion generated by the fluid film was found experimentally and predicted theoretically for certain speeds.

  5. Genomic evidence of geographically widespread effect of gene flow from polar bears into brown bears.

    Science.gov (United States)

    Cahill, James A; Stirling, Ian; Kistler, Logan; Salamzade, Rauf; Ersmark, Erik; Fulton, Tara L; Stiller, Mathias; Green, Richard E; Shapiro, Beth

    2015-03-01

    Polar bears are an arctic, marine adapted species that is closely related to brown bears. Genome analyses have shown that polar bears are distinct and genetically homogeneous in comparison to brown bears. However, these analyses have also revealed a remarkable episode of polar bear gene flow into the population of brown bears that colonized the Admiralty, Baranof and Chichagof islands (ABC islands) of Alaska. Here, we present an analysis of data from a large panel of polar bear and brown bear genomes that includes brown bears from the ABC islands, the Alaskan mainland and Europe. Our results provide clear evidence that gene flow between the two species had a geographically wide impact, with polar bear DNA found within the genomes of brown bears living both on the ABC islands and in the Alaskan mainland. Intriguingly, while brown bear genomes contain up to 8.8% polar bear ancestry, polar bear genomes appear to be devoid of brown bear ancestry, suggesting the presence of a barrier to gene flow in that direction. PMID:25490862

  6. Development and Evaluation of Titanium Spacesuit Bearings

    Science.gov (United States)

    Rhodes, Richard; Battisti, Brian; Ytuarte, Raymond, Jr.; Schultz, Bradley

    2016-01-01

    The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z-series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z-series space suit architecture allows us to reduce mass by an estimated 23 lbs per suit system compared to the previously used stainless steel bearing race designs, without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race- 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility (WSTF) that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approx. 3 years), design parameters for maximum contact stress need to be identified. To identify these design parameters, bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination and design around a cycle life requirement for an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an

  7. Hydrostatic bearings for a turbine fluid flow metering device

    Science.gov (United States)

    Fincke, J.R.

    1980-05-02

    A rotor assembly fluid metering device has been improved by development of a hydrostatic bearing fluid system which provides bearing fluid at a common pressure to rotor assembly bearing surfaces. The bearing fluid distribution system produces a uniform film of fluid distribution system produces a uniform film of fluid between bearing surfaces and allows rapid replacement of bearing fluid between bearing surfaces, thereby minimizing bearing wear and corrosion.

  8. Conditioning of alpha bearing wastes

    International Nuclear Information System (INIS)

    Alpha bearing wastes are generated during the reprocessing of spent fuel, mixed oxide fuel fabrication, decommissioning and other activities. The safe and effective management of these wastes is of particular importance owing to the radiotoxicity and long lived characteristics of certain transuranic (TRU) elements. The management of alpha bearing wastes involves a number of stages which include collection, characterization, segregation, treatment, conditioning, transport, storage and disposal. This report describes the currently available matrices and technologies for the conditioning of alpha wastes and relates them to their compatibility with the other stages of the waste management process. The selection of a specific immobilization process is dependent on the waste treatment state and the subsequent handling, transport, storage and disposal requirements. The overall objectives of immobilization are similar for all waste producers and processors, which are to produce: (a) Waste forms with sufficient mechanical, physical and chemical stability to satisfy all stages of handling, transport and storage (referred to as the short term requirements), and (b) Waste forms which will satisfy disposal requirements and inhibit the release of radionuclides to the biosphere (referred to as the long term requirements). Cement and bitumen processes have already been successfully applied to alpha waste conditioning on the industrial scale in many of the IAEA Member States. Cement systems based on BFS and pozzolanic cements have emerged as the principal encapsulation matrices for the full range of alpha bearing wastes. Alternative technologies, such as polymers and ceramics, are being developed for specific waste streams but are unlikely to meet widespread application owing to cost and process complexity. The merits of alpha waste conditioning are improved performance in transport, storage and disposal combined with enhanced public perception of waste management operations. These

  9. Comparison of Alignment Correction Angles Between Fixed-Bearing and Mobile-Bearing UKA.

    Science.gov (United States)

    Inoue, Atsuo; Arai, Yuji; Nakagawa, Shuji; Inoue, Hiroaki; Yamazoe, Shoichi; Kubo, Toshikazu

    2016-01-01

    Good outcomes have been reported with both fixed-bearing and mobile-bearing unicompartmental knee arthroplasty (UKA). However, overcorrected alignment could induce the progression of arthritis on the non-arthroplasty side. Changes of limb alignment after UKA with both types of bearings (fixed bearing: 24 knees, mobile bearing: 28 knees) were investigated. The mean difference between the preoperative standing femoral-tibial angle (FTA) and postoperative standing FTA was significantly larger in mobile bearing UKA group. In fixed-bearing UKA, there must be some laxity in MCL tension so that a 2-mm tension gauge can be inserted. In mobile-bearing UKA, appropriate MCL tension is needed to prevent bearing dislocation. This difference in MCL tension may have caused the difference in the correction angle between the groups. PMID:26264178

  10. Crystal structure of ethyl 4-[(E)-(4-hy-droxy-3-meth-oxy-benzyl-idene)amino]-benzoate: a p-hy-droxy Schiff base.

    Science.gov (United States)

    Ling, Jing; Kavuru, Padmini; Wojtas, Lukasz; Chadwick, Keith

    2016-07-01

    The title p-hy-droxy Schiff base, C17H17NO4, was synthesized via the condensation reaction of benzocaine with vanillin. The benzyl-idine and benzoate rings are inclined to one another by 24.58 (8)°, and the conformation about the C=N bond is E. In the crystal, mol-ecules are linked by O-H⋯N hydrogen bonds, forming zigzag chains propagating along [010]. Adjacent chains are linked by C-H⋯π and weak offset π-π inter-actions [inter-centroid distance = 3.819 (1) Å], forming sheets parallel to (10-2). PMID:27555938

  11. Excess parameters for binary mixtures of ethyl benzoate with 1-propanol, 1-butanol and 1-pentanol at T=303, 308, 313, 318, and 323 K

    Science.gov (United States)

    Sreehari Sastry, S.; Babu, Shaik; Vishwam, T.; Parvateesam, K.; Sie Tiong, Ha.

    2013-07-01

    Various thermo-acoustic parameters, such as excess isentropic compressibility (KsE), excess molar volume (VE), excess free length (LfE), excess Gibb's free energy (ΔG*E), and excess Enthalpy (HE), have been calculated from the experimentally determined data of density, viscosity and speed of sound for the binary mixtures of ethyl benzoate+1-propanol, or +1-butanol, or +1-pentanol over the entire range of composition at different temperatures (303, 308, 313, 318 and 323 K). The excess functions have been fitted to the Redlich-Kister type polynomial equation. The deviations for excess thermo-acoustic parameters have been explained on the basis of the intermolecular interactions present in these binary mixtures.

  12. Identification of the novel synthetic cannabimimetic 8-quinolinyl 4-methyl-3-(1-piperidinylsulfonyl)benzoate (QMPSB) and other designer drugs in herbal incense.

    Science.gov (United States)

    Blakey, Karen; Boyd, Sue; Atkinson, Sarah; Wolf, Jenna; Slottje, Pim M; Goodchild, Katrina; McGowan, Jenny

    2016-03-01

    The identification and structural elucidation of the novel synthetic cannabimimetic 8-quinolinyl 4-methyl-3-(1-piperidinylsulfonyl)benzoate (QMPSB) by GC-MS, LC-MS and NMR is reported. QMPSB was identified in Queensland, Australia on plant material packaged as herbal incense. The identification of QMPSB was initially hampered due to trans-esterification occurring in the extraction solvent. An investigation of the trans-esterification of QMPSB in methanol and ethanol was conducted and analytical data for the respective methyl and ethyl esters are reported. Analytical data is presented for two other compounds detected on seized plant material packaged as herbal incense: the synthetic cannabimimetic 1-[(N-methylpiperidin-2-yl)methyl]-3-(4-methyl-1-naphthoyl)indole (MAM-1220) and the JWH-081 analogue 1-(cyclohexylmethyl)-3-(4-methoxy-1-naphthoyl)indole (CHM-081).

  13. Simultaneous Determination of Potassium Sorbate, Sodium Benzoate, Quinoline Yellow and Sunset Yellow in Lemonades and Lemon Sauces by HPLC Using Experimental Design.

    Science.gov (United States)

    Dinç Zor, Şule; Aşçı, Bürge; Aksu Dönmez, Özlem; Yıldırım Küçükkaraca, Dilek

    2016-07-01

    In this study, development and validation of a HPLC method was described for simultaneous determination of potassium sorbate, sodium benzoate, quinoline yellow and sunset yellow. A Box-Behnken design using three variables at three levels was employed to determine the optimum conditions of chromatographic separation: pH of mobile phase, 6.0-7.0; flow rate, 0.8-1.2 mL min(-1) and the ratio of mobile phase composed of a 0.025 M sodium acetate/acetic acid buffer, 80-90%. Resolution was chosen as a response. The optimized method was validated for linearity, the limits of detection and quantification, accuracy, precision and stability. All the validation parameters were within the acceptance range. The applicability of the developed method to the determination of these food additives in commercial lemonade and lemon sauce samples was successfully demonstrated. PMID:26951541

  14. Excess parameters for binary mixtures of ethyl benzoate with 1-propanol, 1-butanol and 1-pentanol at T=303, 308, 313, 318, and 323 K

    Energy Technology Data Exchange (ETDEWEB)

    Sreehari Sastry, S., E-mail: sreeharisastry@yahoo.com [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Andhra Pradesh 522 510 (India); Babu, Shaik, E-mail: babu.computers@gmail.com [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Andhra Pradesh 522 510 (India); Vishwam, T., E-mail: vishwam@gitam.edu [Department of Engineering Physics, Gitam University, Hyderabad Campus, Andhra Pradesh 502 239 (India); Parvateesam, K., E-mail: kps27031966@gmail.com [Department of Physics, Acharya Nagarjuna University, Nagarjuna Nagar, Andhra Pradesh 522 510 (India); Sie Tiong, Ha., E-mail: hast@utar.edu.my [Faculty of Science, Department of Chemical Science, Universiti Tunku Abdul Rahman, Jalan Universiti, Bandar Barat, 31900 Kampar, Perak (Malaysia)

    2013-07-01

    Various thermo–acoustic parameters, such as excess isentropic compressibility (K{sub s}{sup E}), excess molar volume (V{sup E}), excess free length (L{sub f}{sup E}), excess Gibb's free energy (ΔG{sup *E}), and excess Enthalpy (H{sup E}), have been calculated from the experimentally determined data of density, viscosity and speed of sound for the binary mixtures of ethyl benzoate+1-propanol, or +1-butanol, or +1-pentanol over the entire range of composition at different temperatures (303, 308, 313, 318 and 323 K). The excess functions have been fitted to the Redlich–Kister type polynomial equation. The deviations for excess thermo–acoustic parameters have been explained on the basis of the intermolecular interactions present in these binary mixtures.

  15. LC-MS/MS Analysis and Pharmacokinetics of Sodium (±-5-Bromo-2-(α-hydroxypentyl Benzoate (BZP, an Innovative Potent Anti-Ischemic Stroke Agent in Rats

    Directory of Open Access Journals (Sweden)

    Xin Tian

    2016-04-01

    Full Text Available A rapid, sensitive and selective liquid chromatography-triple quadrupole mass spectrometry (LC-MS/MS method was developed and validated for the simultaneous determination of sodium (±-5-Bromo-2-(α-hydroxypentyl benzoate (BZP and its active metabolite 3-butyl-6-bromo-1(3H-isobenzofuranone (Br-NBP in rat plasma using potassium 2-(1-hydroxypentyl-benzoate (PHPB and l-3-n-butylphthalide (NBP as internal standards (IS. Chromatographic separation was achieved on a Hypersil GOLD C18 column using a gradient elution of ammonium acetate and methanol at a flow rate of 0.2 mL/min. Good linearity was achieved within the wide concentration range of 5–10,000 ng/mL. The intra-day and inter-day precision was less than 8.71% and the accuracy was within −8.53% and 6.38% in quality control and the lower limit of quantitation samples. BZP and Br-NBP were stable during the analysis and the storage period. The method was successfully applied to pharmacokinetic studies of BZP in Sprague-Dawley rats for the first time. After a single intravenous administration of BZP at the dose of 0.75 mg/kg, the plasma concentration of BZP and Br-NBP declined rapidly and the AUC0-t of BZP was significantly greater in female rats compared to male rats (p < 0.05. The data presented in this study serve as a firm basis for further investigation of BZP in both preclinical and clinical phases.

  16. Risk assessment, cross-resistance potential, and biochemical mechanism of resistance to emamectin benzoate in a field strain of house fly (Musca domestica Linnaeus).

    Science.gov (United States)

    Khan, Hafiz Azhar Ali; Akram, Waseem; Khan, Tiyyabah; Haider, Muhammad Saleem; Iqbal, Naeem; Zubair, Muhammad

    2016-05-01

    Reduced sensitivity to insecticides in insect pests often results in control failures and increases in the dose and frequency of applications, ultimately polluting the environment. Reduced sensitivity to emamectin benzoate, a broad-spectrum agrochemical belonging to the avermectin group of pesticides, was reported in house flies (Musca domestica L.) collected from Punjab, Pakistan, in 2013. The aim of the present study was to investigate the risk for resistance development, biochemical mechanism, and cross-resistance potential to other insecticides in an emamectin benzoate selected (EB-SEL) strain of house flies. A field-collected strain showing reduced sensitivity to emamectin was re-selected in the laboratory for five consecutive generations and compared with a laboratory susceptible (Lab-Susceptible) reference strain, using bioassays. The field strain showed rapid development of resistance to emamectin (resistance ratio (RR) increased from 35.15 to 149.26-fold) as a result of selection experiments; however, resistance declined when the selection pressure uplifted. The EB-SEL strain showed reduction in resistance to abamectin, indoxacarb, and thiamethoxam. The results of synergism experiments using piperonyl butoxide (PBO) and S,S,S-tributylphosphorotrithioate (DEF) enzyme inhibitors and biochemical analyses revealed that the metabolic resistance mechanism was not responsible in developing emamectin resistance in the EB-SEL strain. In conclusion, the risk for the rapid development of emamectin resistance under continuous selection pressure suggests using a multifaceted integrated pest management approach for house flies. Moreover, the instable nature of emamectin resistance in the EB-SEL strain and lack of cross-resistance to other insecticides provide windows for the rotational use of insecticides with different modes of action. This will ultimately reduce emamectin selection pressure and help improving management programs for house flies without polluting the

  17. Coupled Dynamics of a Rotor-Journal Bearing System Equipped with Thrust Bearings

    Directory of Open Access Journals (Sweden)

    Yu Lie

    1995-01-01

    Full Text Available The rotordynamic coefficients of fixed-pad thrust bearing are introduced and calculated by using the out-domain method, and a general analysis method is developed to investigate the coupled dynamics of a rotor equipped with journal and thrust bearings simultaneously. Considerations include the effects of static tilt parameters of the rotor on rotordynamic coefficients of thrust bearing and the action of thrust bearing on system dynamics. It is shown that thrust bearing changes the load distribution of journal bearings and the static deflection of the rotor and delays the instability of the system considerably in lateral shaft vibration.

  18. Bearing Health Assessment Based on Chaotic Characteristics

    Directory of Open Access Journals (Sweden)

    Chen Lu

    2013-01-01

    Full Text Available Vibration signals extracted from rotating parts of machinery carry a lot of useful information about the condition of operating machine. Due to the strong non-linear, complex and non-stationary characteristics of vibration signals from working bearings, an accurate and reliable health assessment method for bearing is necessary. This paper proposes to utilize the selected chaotic characteristics of vibration signal for health assessment of a bearing by using self-organizing map (SOM. Both Grassberger-Procaccia algorithm and Takens' theory are employed to calculate the characteristic vector which includes three chaotic characteristics, such as correlation dimension, largest Lyapunov exponent and Kolmogorov entropy. After that, SOM is used to map the three corresponding characteristics into a confidence value (CV which represents the health state of the bearing. Finally, a case study based on vibration datasets of a group of testing bearings was conducted to demonstrate that the proposed method can reliably assess the health state of bearing.

  19. Cantilever mounted resilient pad gas bearing

    Science.gov (United States)

    Etsion, I. (Inventor)

    1978-01-01

    A gas-lubricated bearing is described, employing at least one pad mounted on a rectangular cantilever beam to produce a lubricating wedge between the face of the pad and a moving surface. The load-carrying and stiffness characteristics of the pad are related to the dimensions and modulus of elasticity of the beam. The bearing is applicable to a wide variety of types of hydrodynamic bearings.

  20. Probabilistic Aspect of Rolling Bearings Durability

    OpenAIRE

    Styp-Rekowski, Michał

    2007-01-01

    Many factors generate situations that real dimensions of each machine elements are different from nominal ones. In the case of rolling bearings elements mentioned disagreements are small - their values are rank of micrometers. However, such small differences can generate significant changes of operational features of bearings. The analysis of influence of ball dimensional deviation on load distribution in ball bearings is presented in this paper. The probability of occurrence of ball diameter...

  1. A miniature tilting pad gas lubricated bearing

    Science.gov (United States)

    Sixsmith, H.; Swift, W. L.

    1983-12-01

    This paper describes the design and development of a miniature tilting pad gas bearing developed for use in very small turbomachines. The bearings have been developed for cryogenic turboexpanders with shaft diameters down to about 0.3 cm and rotational speeds up to one million rpm. Cryogenic expansion turbines incorporating this type of bearing should be suitable for refrigeration rates down to about 10 w.

  2. R+D works for the further development of high temperature reactors. (1) Captive bearing experiments for active magnetic bearings. (2) Captive bearing test for HTR blowers

    International Nuclear Information System (INIS)

    When using active magnetic bearings as blower shaft bearings, blower motors and bearings must be protected against mechanical damage in case of faults (example: total electrical supply failure due to the supply cables breaking). So-called captive bearings are provided, in order to be able to shut the blowers down safely in such faults. These captive bearings are roller bearings which are additionally fitted in the area of the blower shaft bearings, to prevent mechanical contact between the blower rotor and stator. As there was little experience available for the given boundary conditions, such as - speed, - acceleration, - bearing load, - bearing dimensions, - ambient conditions, appropriate development and tests had to be carried out. It was important to determine suitable captive bearings and the necessary ambient conditions, which will make it possible to support the failures of the magnetic bearings to be expected in 40 years' operation of the reactor without damage and to meet the requirements of the captive bearings. (orig./GL)

  3. Bear Capture. Research, and Request for Consideraton of Releases of Bears at Dahomey NWR in 1996

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — A series of memos and correspondences concerning the capture of a bear in Cleveland, MS and release on Dahomey NWR along with graduate research on bears from...

  4. Dynamic modelling and response characteristics of a magnetic bearing rotor system with auxiliary bearings

    Science.gov (United States)

    Free, April M.; Flowers, George T.; Trent, Victor S.

    1995-01-01

    Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotordynamic model which describes the dynamic behavior of a flexible rotor system with magnetic bearings including auxiliary bearings. The model is based upon an experimental test facility. Some simulation studies are presented to illustrate the behavior of the model. In particular, the effects of introducing sideloading from the magnetic bearing when one coil fails is studied.

  5. Dynamic modelling and response characteristics of a magnetic bearing rotor system including auxiliary bearings

    Science.gov (United States)

    Free, April M.; Flowers, George T.; Trent, Victor S.

    1993-01-01

    Auxiliary bearings are a critical feature of any magnetic bearing system. They protect the soft iron core of the magnetic bearing during an overload or failure. An auxiliary bearing typically consists of a rolling element bearing or bushing with a clearance gap between the rotor and the inner race of the support. The dynamics of such systems can be quite complex. It is desired to develop a rotor-dynamic model and assess the dynamic behavior of a magnetic bearing rotor system which includes the effects of auxiliary bearings. Of particular interest is the effects of introducing sideloading into such a system during failure of the magnetic bearing. A model is developed from an experimental test facility and a number of simulation studies are performed. These results are presented and discussed.

  6. Evaluation of bearing configurations using the single bearing tester in liquid nitrogen

    Science.gov (United States)

    Jett, T.; Hall, P.; Thom, R.

    1991-01-01

    Various bearing configurations were tested using the Marshall Space Flight Center single bearing tester with LN2 as the cryogenic coolant. The baseline was one Rocketdyne phase one high pressure oxidizer turbopump (HPOTP) pump end 45-mm bore bearing. The bearing configurations that were tested included a Salox/M cage configuration, a silicon nitride ball configuration, an elongated cage configuration, and a Bray 601 grease configuration.

  7. Journal bearing performance and metrology issues

    Directory of Open Access Journals (Sweden)

    S. Sharma

    2009-01-01

    Full Text Available Purpose: In this paper, a radial clearance of a journal bearings and the metrology of the radial clearance measurement is described.Design/methodology/approach: In this experimental study out-of-roundness and radial clearance of journal bearings were measured with high precision and the impact of their metrology was examined on the specific oil film thickness of the bearing. Some metrological issues were emerged and these should be taken into account when bearings are designed.Findings: An investigation showed that the radial clearance measurements can vary from one measuring device to another and the specified clearance may not necessarily meet the design criteria of specific oil film thickness. The study indicates that the radial clearance measurement can differ from one measuring device to another depending upon the precision that can be achieved by the device. The radius of the bearing or the shaft also varies along the circumference, mainly due to out-of-roundness. The out-of-roundness contributes to the error in radial clearance measurement and hence similar to the cut off length specified with the surface roughness, the out-of-roundness needs to be specified with the radial clearance.Practical implications: The radial clearance of a journal bearing is a key design parameter and bearing performance mainly depends upon this parameter. In this paper was showed that the metrology of the radial clearance measurement plays a significant role and not only that the bearing manufacturer or the user of the bearing is aware of this fact but the bearing designer must also take this fact into account while designing bearingsOriginality/value: This paper showed that The radial clearance is a sensitive micro-geometry parameter and hence metrology plays a vital role in making decisions

  8. Active magnetic bearing-supported rotor with misaligned cageless backup bearings: A dropdown event simulation model

    Science.gov (United States)

    Halminen, Oskari; Kärkkäinen, Antti; Sopanen, Jussi; Mikkola, Aki

    2015-01-01

    Active magnetic bearings (AMB) offer considerable benefits compared to regular mechanical bearings. On the other hand, they require backup bearings to avoid damage resulting from a failure in the component itself, or in the power or control system. During a rotor-bearing contact event - when the magnetic field has disappeared and the rotor drops on the backup bearings - the structure of the backup bearings has an impact on the dynamic actions of the rotor. In this paper, the dynamics of an active magnetic bearing-supported rotor during contact with backup bearings is studied with a simulation model. Modeling of the backup bearings is done using a comprehensive cageless ball bearing model. The elasticity of the rotor is described using the finite element method (FEM) and the degrees of freedom (DOF) of the system are reduced using component mode synthesis. Verification of the misaligned cageless backup bearings model is done by comparing the simulation results against the measurement results. The verified model with misaligned cageless backup bearings is found to correspond to the features of a real system.

  9. Phylogeography of mitochondrial DNA variation in brown bears and polar bears

    Science.gov (United States)

    Shields, Gerald F.; Adams, Deborah; Garner, Gerald; Labelle, Martine; Pietsch, Jacy; Ramsay, Malcolm; Schwartz, Charles; Titus, Kimberly; Williamson, Scott

    2000-01-01

    We analyzed 286 nucleotides of the middle portion of the mitochondrial cytochrome b gene of 61 brown bears from three locations in Alaska and 55 polar bears from Arctic Canada and Arctic Siberia to test our earlier observations of paraphyly between polar bears and brown bears as well as to test the extreme uniqueness of mitochondrial DNA types of brown bears on Admiralty, Baranof, and Chichagof (ABC) islands of southeastern Alaska. We also investigated the phylogeography of brown bears of Alaska's Kenai Peninsula in relation to other Alaskan brown bears because the former are being threatened by increased human development. We predicted that: (1) mtDNA paraphyly between brown bears and polar bears would be upheld, (2) the mtDNA uniqueness of brown bears of the ABC islands would be upheld, and (3) brown bears of the Kenai Peninsula would belong to either clade II or clade III of brown bears of our earlier studies of mtDNA. All of our predictions were upheld through the analysis of these additional samples.

  10. Methods and systems for micro bearings

    Science.gov (United States)

    Stalford, Harold L.

    2012-10-09

    A micro drive assembly may comprise a substrate, a micro shall oriented in-plane with the substrate and at least one micro bearing to support rotation of the micro shaft. The micro shaft and micro bearing may be in or less than the micrometer domain.

  11. Shaft Center Orbit in Dynamically Loaded Bearings

    DEFF Research Database (Denmark)

    Klit, Peder

    2005-01-01

    The aim of this work is to demonstrate how to utilize the bearings damping coe±cients to estimate the orbit for a dynamically loaded journal bearing. The classical method for this analysis was developed by Booker in 1965 [1]and described further in 1972 [2]. Several authors have re¯ned this method...... over the years. In 1966 Jorgen W. Lund [5]published an approach to ¯nd the dynamic coe±cients of a journal bearing by a ¯rst order perturbation of the Reynold's equation. These coe±cients made it possible to perform a rotor-bearing stability analysis for a statically loaded bearing. In the mid...... seventies Jorgen W. Lund pointed out in lecture notes that the dynamic damping coe±cients of the bearing could be used to ¯nd the shaft orbit for dynamically loaded bearings. For simplicity the "Short-Width-Journal-Bearing Theory" is used as a basis for ¯nding the damping coe±cients in this work...

  12. Measurement of wear in radial journal bearings

    NARCIS (Netherlands)

    Ligterink, D.J.; Gee, de A.W.J.

    1996-01-01

    this article, the measurement of wear in radial journal bearings is discussed, where a distinction is made between stationary and non-stationary contact conditions. Starting with Holm/Archard's wear law, equations are derived for the calculation of the specific wear rate k of the bearing material as

  13. Movie Director Bags a Silver Bear

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Chinese director and film writer Wang Xiaoshuai has walked away with the Silver Bear award at the 58th Berlin International Film Festival for best script of Zuo You, or In Love We Trust. Back in 2001, Wang won his first Silver Bear award for directing Beijing

  14. Trends in Controllable Oil Film Bearings

    DEFF Research Database (Denmark)

    Santos, Ilmar

    2011-01-01

    the rotational speed ranges by improving damping and eliminating instability problems, for example, by compensating cross-coupling destabilizing effects; reducing startup torque and energy dissipation in bearings; compensating thermal effects. It is shown that such controllable bearings can act as "smart...

  15. Nonlinear Dynamic Response of Compliant Journal Bearings

    Directory of Open Access Journals (Sweden)

    Glavatskih S.

    2012-07-01

    Full Text Available This paper investigates the dynamic response of the compliant tilting pad journal bearings subjected to synchronous excitation. Bearing compliance is affected by the properties of pad liner and pad support geometry. Different unbalance eccentricities are considered. It is shown that bearing dynamic response is non-linear. Journal orbit complexity increases with pad compliance though the orbit amplitudes are marginally affected at low loads. At high loads, the journal is forced to operate outside the bearing clearance. The polymer liner reduces the maximum oil film pressure by a factor of 2 when compared to the white metal liner. The nonlinear dynamic response of compliant tilting pad journal bearings is thoroughly discussed.

  16. EFFECT OF CLEARANCE THE BALL BEARINGS ON INCORRECT WORK OF THREE-SUPORT BEARING SHAFT

    OpenAIRE

    Jarosław KACZOR

    2014-01-01

    Durability deep groove ball bearings depends on factors (called attributes) design, technological and operational. Among the design features one of the most important is play in the bearings. Polish Norm shows five groups of looseness in the bearings, in which the play range from 0 to 105 microns. Manufacturers of rolling bearings they only play group, which has a bearing data, without giving the exact value of the slack. Aim of this study is to determine how it affects the play in the bea...

  17. THE STRUCTURAL ANALYSIS OF STEEL SILOS WITH CYLINDRICAL-WALL BEARING AND PROFILE-STEEL BEARING

    Directory of Open Access Journals (Sweden)

    Zhengjun Tang

    2015-04-01

    Full Text Available The silos are widely used in bulk material in many fields such as agriculture, mining, chemical, electric power storage, etc. Thin metal cylindrical silo shells are vulnerable to buckling failure caused by the compressive wall friction force. In this paper, the structural analysis of two types of steel silo with cylindrical-wall bearing and profile-steel bearing is implemented by Abaqus finite element analysis. The results indicate that under the same loading conditions, steel silos with profile-steel bearing and cylindrical-Wall bearing have similar values in Mises stress, but the steel silo with profile-steel bearing has a smaller radial displacement and a better capability of buckling resistance. Meanwhile, the total steel volumes reduced 8.0% comparing to the steel silo with cylindrical-wall bearing. Therefore, steel soil with profile-steel bearing not only has a less steel volumes but also a good stability.

  18. Vibration model of rolling element bearings in a rotor-bearing system for fault diagnosis

    Science.gov (United States)

    Cong, Feiyun; Chen, Jin; Dong, Guangming; Pecht, Michael

    2013-04-01

    Rolling element bearing faults are among the main causes of breakdown in rotating machines. In this paper, a rolling bearing fault model is proposed based on the dynamic load analysis of a rotor-bearing system. The rotor impact factor is taken into consideration in the rolling bearing fault signal model. The defect load on the surface of the bearing is divided into two parts, the alternate load and the determinate load. The vibration response of the proposed fault signal model is investigated and the fault signal calculating equation is derived through dynamic and kinematic analysis. Outer race and inner race fault simulations are realized in the paper. The simulation process includes consideration of several parameters, such as the gravity of the rotor-bearing system, the imbalance of the rotor, and the location of the defect on the surface. The simulation results show that different amplitude contributions of the alternate load and determinate load will cause different envelope spectrum expressions. The rotating frequency sidebands will occur in the envelope spectrum in addition to the fault characteristic frequency. This appearance of sidebands will increase the difficulty of fault recognition in intelligent fault diagnosis. The experiments given in the paper have successfully verified the proposed signal model simulation results. The test rig design of the rotor bearing system simulated several operating conditions: (1) rotor bearing only; (2) rotor bearing with loader added; (3) rotor bearing with loader and rotor disk; and (4) bearing fault simulation without rotor influence. The results of the experiments have verified that the proposed rolling bearing signal model is important to the rolling bearing fault diagnosis of rotor-bearing systems.

  19. 中心组合设计优化复凝聚法制备甲维盐微囊工艺%Optimization of Technology for Complex Coacervation on Emamectin Benzoate Microcapsule Preparation by Center Composite Design

    Institute of Scientific and Technical Information of China (English)

    陈效忠; 李守君; 李晓凤; 王玉峰; 于莲; 慎爱民; 江欣; 苏瑾; 宗希明

    2012-01-01

    [Aims] Optimized the preparation technology of emamectin-benzoate microcapsule. [Methods] Emamectin-benzoate was encapsulated into microcapsules using gelatin and arabic gum as coating materials by complex coacervation. Mass concentration of the emamectin-benzoate was analysed by UV spectrophotometry and the entrapment rate was reckoned. The entrapment rate was used as index, and the preparation technology was optimized by CCD. [Results] The optimum technology conditions of emamectin benzoate microcapsule was set up. The stirred rate was 600 r/min, the reaction temperature was 47 ℃, the reaction time was 107 min and the entrapment rate was 74.27%. [Conclusions] The deviation between predictive value of CCD and measured value was little, optimize method was feasible, and the entrapment rate was higher than before.%[目的]优化甲维盐微囊制备工艺.[方法]实验以明胶和阿拉伯胶为壁材,采用复凝聚法制备甲维盐微囊.用紫外分光光度法测定甲维盐含量,计算包封率.以包封率为指标,通过中心组合设计对制备工艺进行优化.[结果]复凝聚法制备甲维盐微囊的最佳工艺为600 r/min,47℃,反应107 min,包封率为74.27%.[结论]CCD预测值与实际测量值偏差小,优化方法可行,且包封率较高.

  20. Synchronization of ovulation in crossbred dairy heifers using gonadotrophin-releasing hormone agonist, prostaglandin F2a and human chorionic gonadotrophin or estradiol benzoate

    Directory of Open Access Journals (Sweden)

    Castilho C.

    2000-01-01

    Full Text Available Girolando (Gir x Holstein is a very common dairy breed in Brazil because it combines the rusticity of Gir (Bos indicus with the high milk yield of Holstein (Bos taurus. The ovarian follicular dynamics and hormonal treatments for synchronization of ovulation and timed artificial insemination were studied in Girolando heifers. The injection of a gonadotrophin-releasing hormone (GnRH agonist was followed 6 or 7 days (d later by prostaglandin F2a (PGF2a. Twenty-four hours after PGF2a injection either human chorionic gonadotropin (hCG, GPh-d6 and GPh-d7 groups or estradiol benzoate (EB, GPE-d6 and GPE-d7 groups was administered to synchronize ovulation and consequently allow timed artificial insemination (AI 24 and 30 h after hCG and EB injection, respectively. Follicular dynamics in Girolando heifers was characterized by the predominance of three follicular waves (71.4% with sizes of dominant follicles (10-13 mm and corpus luteum (approximately 20 mm similar to those for Bos indicus cattle. In the GnRH-PGF-hCG protocol, hCG administration induced earlier ovulation (67.4 h, P<0.01 compared to the control group (GnRH-PGF and a better synchronization of ovulation, since most of it occurred within a period of 12 to 17 h. Pregnancy rate after timed AI was 42.8 (3/7, GPh-d6 to 50% (7/14, GPh-d7. In contrast, estradiol benzoate (GnRH-PGF-EB protocol synchronized ovulation of only 5 of 11 heifers from the GPE-d7 group and of none (0/7 from the GPE-d6 group, which led to low pregnancy rates after timed AI (27.3 and 0%, respectively. However, since a small number of Girolando heifers was used to determine pregnancy rates in the present study, pregnancy rates should be confirmed with a larger number of animals.

  1. Antifungal Activity of Diglycerin Ester of Fatty Acids against Yeasts and Its Comparison with Those of Sucrose Monopalmitate and Sodium Benzoate.

    Science.gov (United States)

    Shimazaki, Aiko; Sakamoto, Jin J; Furuta, Masakazu; Tsuchido, Tetsuaki

    2016-01-01

    The antifungal activities of diglycerin monoester of fatty acids (DGCs), which have been employed as food emulsifiers, were examined against three yeasts, Saccharomyces cerevisiae, Candida albicans and Candida utilis and were compared with those of sucrose monoester of palmitic acid (SC16) as another type of emulsifier and sodium benzoate (SB) as a weak acid food preservative. When the minimum growth inhibitory concentrations (MICs) of diglycerin monolaurate (DGC12) against these yeasts were determined 2 d after incubation in YM broth at pH5.0, they were relatively low, being 0.01% (w/v), for both S. cerevisiae and C. utilis, whereas was high, being 4.0% (w/v), for C. albicans. On the contrary, the MICs of sucrose monopalmitate (SC16) were high, being 3.0 and 4.0% (w/v), for the former two yeasts, respectively, but 0.6% (w/v) for the last yeast. In contrast to these emulsifiers, the MICs of sodium benzoate (SB) were similar independently upon the yeast strain, being in order 0.4, 0.3 and 0.5% (w/v), for the above yeasts, respectively. The anti-yeast activities of DGC12 and SC16 were gradually increased with a decrease in pH, in a manner similar to that of SB, except for the action of SC16 on C. albicans, for which the activity was more effective at pHs 5.0 and 6.0 than at pHs 4.0 and 7.0. Among DGCs tested having different fatty acid moieties in the molecule, lauroyl ester (DGC12) was more effective than myristoyl and palmitoyl esters against S. cerevisiae and C. utilis. The inhibitory effect of DGC12 on the yeast growth depended upon both the cell density and the strength of aeration during the treatment. Further, DGC12 was found to kill S. cerevisiae and C. utilis cells at a rather low concentration of 0.005% (w/v) in 50mM acetate buffer at pH5.0, although, against C. albicans cells, only slight fungicidal activity was demonstrated at a high concentration of 0.5% (w/v). The results obtained support the effectiveness of practical application of DGC12 to acidic

  2. Space Telescope Fine Guidance Sensor Bearing Anomaly

    Science.gov (United States)

    Loewenthal, S.; Esper, J.; Pan, J.; Decker, J.

    1996-01-01

    Early in 1993, a servo motor within one of three Fine Guidance Sensors (FGS) aboard the Hubble Space Telescope (HST) reached stall torque levels on several occasions. Little time was left to plan replacement during the first servicing mission, scheduled at the end of '93. Accelerated bearing life tests confirmed that a small angle rocking motion, known as Coarse Track (CT), accelerated bearing degradation. Saturation torque levels were reached after approximately 20 million test cycles, similar to the flight bearings. Reduction in CT operation, implemented in flight software, extended FGS life well beyond the first servicing mission. However in recent years, bearing torques have resumed upward trends and together with a second, recent bearing torque anomaly has necessitated a scheduled FGS replacement during the upcoming second servicing mission in '97. The results from two series of life tests to quantify FGS bearing remaining life, discussion of bearing on-orbit performance, and future plans to service the FGS servos are presented in this paper.

  3. Genomic sequencing of Pleistocene cave bears

    Energy Technology Data Exchange (ETDEWEB)

    Noonan, James P.; Hofreiter, Michael; Smith, Doug; Priest, JamesR.; Rohland, Nadin; Rabeder, Gernot; Krause, Johannes; Detter, J. Chris; Paabo, Svante; Rubin, Edward M.

    2005-04-01

    Despite the information content of genomic DNA, ancient DNA studies to date have largely been limited to amplification of mitochondrial DNA due to technical hurdles such as contamination and degradation of ancient DNAs. In this study, we describe two metagenomic libraries constructed using unamplified DNA extracted from the bones of two 40,000-year-old extinct cave bears. Analysis of {approx}1 Mb of sequence from each library showed that, despite significant microbial contamination, 5.8 percent and 1.1 percent of clones in the libraries contain cave bear inserts, yielding 26,861 bp of cave bear genome sequence. Alignment of this sequence to the dog genome, the closest sequenced genome to cave bear in terms of evolutionary distance, revealed roughly the expected ratio of cave bear exons, repeats and conserved noncoding sequences. Only 0.04 percent of all clones sequenced were derived from contamination with modern human DNA. Comparison of cave bear with orthologous sequences from several modern bear species revealed the evolutionary relationship of these lineages. Using the metagenomic approach described here, we have recovered substantial quantities of mammalian genomic sequence more than twice as old as any previously reported, establishing the feasibility of ancient DNA genomic sequencing programs.

  4. Grizzly bear diet shifting on reclaimed mines

    Directory of Open Access Journals (Sweden)

    Bogdan Cristescu

    2015-07-01

    Full Text Available Industrial developments and reclamation change habitat, possibly altering large carnivore food base. We monitored the diet of a low-density population of grizzly bears occupying a landscape with open-pit coal mines in Canada. During 2009–2010 we instrumented 10 bears with GPS radiocollars and compared their feeding on reclaimed coal mines and neighboring Rocky Mountains and their foothills. In addition, we compared our data with historical bear diet for the same population collected in 2001–2003, before extensive mine reclamation occurred. Diet on mines (n=331 scats was dominated by non-native forbs and graminoids, while diets in the Foothills and Mountains consisted primarily of ungulates and Hedysarum spp. roots respectively, showing diet shifting with availability. Field visitation of feeding sites (n=234 GPS relocation clusters also showed that ungulates were the main diet component in the Foothills, whereas on reclaimed mines bears were least carnivorous. These differences illustrate a shift to feeding on non-native forbs while comparisons with historical diet reveal emergence of elk as an important bear food. Food resources on reclaimed mines attract bears from wilderness areas and bears may be more adaptable to landscape change than previously thought. The grizzly bear’s ready use of mines cautions the universal view of this species as umbrella indicative of biodiversity.

  5. 甲维盐与苏云金杆菌复配对黄野螟增效作用研究%Studies on the Synergistic Effects of Emamectin--benzoate and Bacillus thuringiensis on Heortia vitessoides Moore

    Institute of Scientific and Technical Information of China (English)

    王玲; 郑礼飞; 陈志云; 李东文; 曹春雷; 李奕震

    2012-01-01

    The synergistic effects of Emamectin--benzoate, Bacillus thuringiensis, and their mixtures on Heortza wtessoides were tested in the laboratory by the leaf--dipping method. The results showed that the LC50 of Emamectin--benzoate and Bacillus thuringiensis were 0. 0000001286mg/L and 0. 0006943385mg/L, respectively. The mixture of Emamectin--benzoate and Bacillus thuringiensis with ratio of 8 : 2, 7 : 3 or 6:4 had remarkable synergistic effects.%采用浸叶法测定了两种农药对黄野螟的增效作用及两种药剂复配的适宜配比。结果表明:甲维盐和苏云金杆菌对黄野螟的制剂LC50值分别是0.0000001286mg/L和0.0006943385mg/L,前者毒力大于后者;两者以重量比为8∶2、7:3和6:4混配时的增效作用最明显。

  6. Design of gas bearing systems for precision applications

    Science.gov (United States)

    Wang, Junming

    Research to provide the up to date knowledge and efficient tools to design better Externally Pressurized Gas (EPG) bearing systems, including the design of individual bearings, and to arrange all the bearings used in an optimal way is reported. Both circular and rectangular EPG pads with rigid bearing surfaces and rigid inlet restrictors were used. The following topics closely related to the applications in precision engineering are discussed: influences of gap shape on the bearing performance; effects of bearing body tilt on the bearing performance; influences of bearing surface imperfections on bearing performance; temperature drops in EPG bearings in quasistationary conditions; the optimal use of multiple bearings in a mechanical system; the use of EPG bearing damping characteristics in the design; and the effects of motion velocity.

  7. Future bearing surfaces in total hip arthroplasty.

    Science.gov (United States)

    Chang, Jun-Dong

    2014-03-01

    One of the most important issues in the modern total hip arthroplasty (THA) is the bearing surface. Extensive research on bearing surfaces is being conducted to seek an ideal bearing surface for THA. The ideal bearing surface for THA should have superior wear characteristics and should be durable, bio-inert, cost-effective, and easy to implant. However, bearing surfaces that are currently being implemented do not completely fulfill these requirements, especially for young individuals for whom implant longevity is paramount. Even though various new bearing surfaces have been investigated, research is still ongoing, and only short-term results have been reported from clinical trials. Future bearing surfaces can be developed in the following ways: (1) change in design, (2) further improvement of polyethylene, (3) surface modification of the metal, (4) improvement in the ceramic, and (5) use of alternative, new materials. One way to reduce wear and impingement in THA is to make changes in its design by using a large femoral head, a monobloc metal shell with preassembled ceramic liner, dual mobility cups, a combination of different bearing surfaces, etc. Polyethylene has improved over time with the development of highly crosslinked polyethylene. Further improvements can be made by reinforcing it with vitamin E or multiwalled carbon nanotubes and by performing a surface modification with a biomembrane. Surface modifications with titanium nitride or titanium niobium nitride are implemented to try to improve the metal bearings. The advance to the fourth generation ceramics has shown relatively promising results, even in young patients. Nevertheless, further improvement is required to reduce fragility and squeaking. Alternative materials like diamond coatings on surfaces, carbon based composite materials, oxidized zirconium, silicon nitride, and sapphire are being sought. However, long-term studies are necessary to confirm the efficacy of these surfaces after enhancements

  8. Eastern slopes grizzly bear project : project update

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    This report updates a study to examine the cumulative effects of human activities on the grizzly bears in the central Canadian Rockies. The project was initiated in 1994 to acquire accurate scientific information on the habitat and populations of grizzly bears in the area of the Banff National Park and Kananaskis Country. This area is probably the most heavily used and developed area where the grizzly still survives. The information gathered throughout the course of the study is used to better protect and manage the bears and other sensitive carnivores in the region. Using telemetry, researchers monitored 25 grizzly bears which were radio-collared in a 22,000 square-kilometer area in the upper Bow Valley drainage of the eastern Alberta slopes. The researchers worked with representatives from Husky Oil and Rigel Energy on the development of the Moose Mountain oil and gas field without adversely affecting the grizzly bear population. Information collected over eight years indicates that the grizzly bears have few and infrequent offspring. Using the information gathered thus far, the location of the Moose Mountain to Jumping Pound pipeline was carefully selected, since the bears suffer from high mortality, and the food and cover had already been compromised by the high number of roads, trails and other human activities in the area. The research concluded in November 2001 provides sufficient information to accurately asses the status of the grizzly bear population and habitat. The data will be analyzed and integrated in 2002 into models that reflect the variables affecting grizzly bears and a final report will be published.

  9. Corporate risks, risk bearing ability and equity

    OpenAIRE

    Handschin, Lukas

    2011-01-01

    There is a relation between corporate risks, risk bearing ability and equity. In order to assess the risk bearing ability of a corporation, one reference figure is equity, understood as the sum of legal capital and reserves, free reserves and accrued profits. Equity shows the risk bearing ability related to the risk of asset reduction as well as the ability of the corporation to attract new liquidity by increasing debts, in case of a negative free cash flow. Equity is the risk reserve of the ...

  10. Microeconomic analysis of military aircraft bearing restoration

    Science.gov (United States)

    Hein, G. F.

    1976-01-01

    The risk and cost of a bearing restoration by grinding program was analyzed. A microeconomic impact analysis was performed. The annual cost savings to U.S. Army aviation is approximately $950,000.00 for three engines and three transmissions. The capital value over an indefinite life is approximately ten million dollars. The annual cost savings for U.S. Air Force engines is approximately $313,000.00 with a capital value of approximately 3.1 million dollars. The program will result in the government obtaining bearings at lower costs at equivalent reliability. The bearing industry can recover lost profits during a period of reduced demand and higher costs.

  11. Compressor ported shroud for foil bearing cooling

    Science.gov (United States)

    Elpern, David G.; McCabe, Niall; Gee, Mark

    2011-08-02

    A compressor ported shroud takes compressed air from the shroud of the compressor before it is completely compressed and delivers it to foil bearings. The compressed air has a lower pressure and temperature than compressed outlet air. The lower temperature of the air means that less air needs to be bled off from the compressor to cool the foil bearings. This increases the overall system efficiency due to the reduced mass flow requirements of the lower temperature air. By taking the air at a lower pressure, less work is lost compressing the bearing cooling air.

  12. Hydrostatic, aerostatic and hybrid bearing design

    CERN Document Server

    Rowe, W Brian

    2012-01-01

    Solve your bearing design problems with step-by-step procedures and hard-won performance data from a leading expert and consultant Compiled for ease of use in practical design scenarios, Hydrostatic, Aerostatic and Hybrid Bearing Design provides the basic principles, design procedures and data you need to create the right bearing solution for your requirements. In this valuable reference and design companion, author and expert W. Brian Rowe shares the hard-won lessons and figures from a lifetime's research and consultancy experience. Coverage includes: Clear e

  13. Transient unbalance response of four multilobe journal bearings

    Science.gov (United States)

    Allaire, P. E.; Li, D. F.; Choy, K. C.

    1979-01-01

    This work carries out an analysis of the transient response of four multilobe journal bearings (elliptical, offset, three-lobe, and four-lobe) subject to unbalance both below and above the linearized stability thresholds for the bearings. It extends the work of a previous paper on a balanced rotor in the same four bearing types. Transient orbits, bearing forces, and a numerical fast Fourier transform analysis of the orbits are presented. A comparison of bearing forces above the stability threshold for each bearing indicates that the elliptical bearing has the most violent whirl vibration amplitudes, while the offset bearing exhibits the least amount of subsynchronous vibration.

  14. Three-dimensional (3-D) metal-organic frameworks with 3-pyridin-4-yl-benzoate defining new (3,6)-connected net topologies

    International Nuclear Information System (INIS)

    Reactions of different metal salts with 3-pyridin-4-yl-benzoic acid (3,4-Hpybz) under ambient condition afford a series of 3-D metal-organic frameworks with two new types of (3,6)-connected net topologies. In the isomorphic complexes [M2(μ-H2O)(3,4-pybz)4]n (MII=MnII for 1, ZnII for 2, or CdII for 3), the octahedral metal nodes are extended by the 3-connected pybz tectons to constitute 3-D arrays with the Schlaefli symbol of (3.4.5)(32.44.55.62.72), whereas [Pb(3,4-pybz)2]n (4) shows a completely different 3-D (42.6)2(44.62.89) framework, which represents a subnet of the (4,8)-connected fluorite lattice. - Graphical abstract: This work presents a series of 3-D metal-organic frameworks with 3-pyridin-4-yl-benzoate, which display new (3,6)-connected net topologies of (3.4.5)(32.44.55.62.72) for MnII/ZnII/CdII and (42.6)2(44.62.89) for PbII species.

  15. Determination of 2-ethylhexyl 4-(dimethylamino) benzoate using membrane-assisted liquid-liquid extraction and gas chromatography-mass spectrometric detection.

    Science.gov (United States)

    March, J G; Genestar, C; Simonet, B M

    2009-06-01

    A flow-cell for micro-porous membrane liquid-liquid extraction with a sheet membrane was used to extract 2-ethylhexyl 4-(dimethylamino) benzoate (EDB) from urine of solar-cream users and spiked wine samples. The cell enabled the target analyte to be extracted from 7.9 mL of donor solution into 200 microL of acceptor solution (decane). After extraction, the acceptor solution was transferred to a micro-vial for GC-MS analysis without derivation. In this work, variables affecting the enrichment factor were also studied, such as organic solvent, extraction time, recirculation flow of the donor solution through the donor chamber, presence of potassium chloride and ethanol in the donor solution and pH. The method has been evaluated in terms of linearity, sensitivity, precision, limits of detection and quantification and extraction efficiency. Limits of quantification were 1 and 3 microg L(-1) EDB for urine and wine, respectively. Quantitative analysis has been carried out by applying the method of standard additions. Within- and between-day relative standard deviations were lower than 12% and 20%, respectively. EDB was found in the urine of users of cream containing EDB in the concentration interval 1.2-7.2 microg L(-1). Therefore, this provides evidence of EDB dermal absorption and subsequent excretion through the urinary tract. EDB was not found in the analysed wine samples. PMID:19347661

  16. Self-assembly and UV-curing Property of Polymerized Lyotropic Liquid Crystal Monomer of Sodium 3,4,5-tris(11-acryloxyundecyloxy)benzoate

    Institute of Scientific and Technical Information of China (English)

    Yu-qin Bai; Jin-bao Guo; Ying Wang; Jie Wei

    2013-01-01

    A polymerized lyotropic liquid crystal monomer of sodium 3,4,5-tris (11-acryloxyundecyloxy)benzoate was synthesized by a convenient route starting from 3,4,5-trihydroxybenzoic acid via esterification followed by etherification,acylation and finally neutralization.The chemical structure was confirmed by Fourier transform infrared (FT-IR) and 1H nuclear magnetic resonance spectral analysis.The self-organization behavior of the monomer with deionized water in methanol at room temperature was also demonstrated.The assemblies were characterized by polarized optical microscope and X-ray diffraction.The results show that a solution containing 80∶20 of the monomer to water was found to be able to self-organize into Lamellar (La) phase and 92∶8 with inverted hexagonal (HⅡ) phase,which was in accordance with the theoretical calculation of critical packing parameter.It suggests that the concentration of the monomer was the key factor to influence assembly structure.Additionally,the acrylate conversion with different photoinitiators and nanostructure retention after polymerization were investigated.The research shows that the acrylate conversion of the monomer with Darocur2959 could reach up to 78% when irradiated by 30 mW/cm2 UV light of 365 nm for 30 min characterized by Real-time FT-IR as well as the sol-gel method.Meanwhile,the La and HⅡI phase nanostructures were both retained after polymerization.

  17. Study of the photochemical transformation of 2-ethylhexyl 4-(dimethylamino)benzoate (OD-PABA) under conditions relevant to surface waters.

    Science.gov (United States)

    Calza, P; Vione, D; Galli, F; Fabbri, D; Dal Bello, F; Medana, C

    2016-01-01

    We studied the aquatic environmental fate of 2-ethylhexyl 4-(dimethylamino)benzoate (OD-PABA), a widespread sunscreen, to assess its environmental persistence and photoinduced transformation. Direct photolysis is shown to play a key role in phototransformation, and this fast process is expected to be the main attenuation route of OD-PABA in sunlit surface waters. The generation of transformation products (TPs) was followed via HPLC/HRMS. Five (or four) TPs were detected in the samples exposed to UVB (or UVA) radiation, respectively. The main detected TPs of OD-PABA, at least as far as HPLC-HRMS peak areas are concerned, would involve a dealkylation or hydroxylation/oxidation process in both direct photolysis and indirect phototransformation. The latter was simulated by using TiO2-based heterogeneous photocatalysis, involving the formation of nine additional TPs. Most of them resulted from the further degradation of the primary TPs that can also be formed by direct photolysis. Therefore, these secondary TPs might also occur as later transformation intermediates in natural aquatic systems. PMID:26512801

  18. Study of the photochemical transformation of 2-ethylhexyl 4-(dimethylamino)benzoate (OD-PABA) under conditions relevant to surface waters.

    Science.gov (United States)

    Calza, P; Vione, D; Galli, F; Fabbri, D; Dal Bello, F; Medana, C

    2016-01-01

    We studied the aquatic environmental fate of 2-ethylhexyl 4-(dimethylamino)benzoate (OD-PABA), a widespread sunscreen, to assess its environmental persistence and photoinduced transformation. Direct photolysis is shown to play a key role in phototransformation, and this fast process is expected to be the main attenuation route of OD-PABA in sunlit surface waters. The generation of transformation products (TPs) was followed via HPLC/HRMS. Five (or four) TPs were detected in the samples exposed to UVB (or UVA) radiation, respectively. The main detected TPs of OD-PABA, at least as far as HPLC-HRMS peak areas are concerned, would involve a dealkylation or hydroxylation/oxidation process in both direct photolysis and indirect phototransformation. The latter was simulated by using TiO2-based heterogeneous photocatalysis, involving the formation of nine additional TPs. Most of them resulted from the further degradation of the primary TPs that can also be formed by direct photolysis. Therefore, these secondary TPs might also occur as later transformation intermediates in natural aquatic systems.

  19. Toughening of Epoxy Resin with Solid Amine Terminated Poly (ethy-lene glycol) Benzoate and Effect of Red Mud Waste Particles

    Institute of Scientific and Technical Information of China (English)

    B.C.Samanta; T.Maity; S.Dalai; A.K.Banthia

    2008-01-01

    An investigation was carried out to modify the toughness of triethylene tetramine cured DGEBA (diglycidyl ether of bisphenol-A) resin using solid amine terminated poly (ethylene glycol) benzoate (ATPEGB) as modifier with and without red mud waste particles. The solid ATPEGB modifier synthesized from the acid catalyzed esterification reaction of poly (ethylene glycol) (PEG) and 4-amino benzoic acid was characterized by Fourier transform infrared spectroscopy (FT-IR) and 1H-NMR (nuclear magnetic resonance) spectroscopies, viscosity measurements, and solubility parameter calculation. The unfilled and red mud waste filled modified epoxy networks were evaluated with impact, adhesive, tensile, flexural and thermal properties by differential scanning calorimetry (DSC), thermogravimetric (TG) and dynamic mechanical analysis (DMA). The effect of modifier concentration and red mud waste particles on toughening behavior was also investigated. The optimum properties were obtained at 12.5 phr (parts per hundred parts of resin) concentration of the modifier. The ATPEGB modified cured epoxy was thermally stable up to 315℃. The morphology on fracture surfaces of cured epoxy was also analyzed by scanning electron microscopy (SEM).

  20. Molecular phylogeny and SNP variation of polar bears (Ursus maritimus), brown bears (U. arctos), and black bears (U. americanus) derived from genome sequences.

    Science.gov (United States)

    Cronin, Matthew A; Rincon, Gonzalo; Meredith, Robert W; MacNeil, Michael D; Islas-Trejo, Alma; Cánovas, Angela; Medrano, Juan F

    2014-01-01

    We assessed the relationships of polar bears (Ursus maritimus), brown bears (U. arctos), and black bears (U. americanus) with high throughput genomic sequencing data with an average coverage of 25× for each species. A total of 1.4 billion 100-bp paired-end reads were assembled using the polar bear and annotated giant panda (Ailuropoda melanoleuca) genome sequences as references. We identified 13.8 million single nucleotide polymorphisms (SNP) in the 3 species aligned to the polar bear genome. These data indicate that polar bears and brown bears share more SNP with each other than either does with black bears. Concatenation and coalescence-based analysis of consensus sequences of approximately 1 million base pairs of ultraconserved elements in the nuclear genome resulted in a phylogeny with black bears as the sister group to brown and polar bears, and all brown bears are in a separate clade from polar bears. Genotypes for 162 SNP loci of 336 bears from Alaska and Montana showed that the species are genetically differentiated and there is geographic population structure of brown and black bears but not polar bears. PMID:24477675

  1. Polar bear research in Alaska, spring 1982

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — An investigation of the ecology and population dynamics of Alaskan polar bears has continued since 1967. As part of that program, U.S. Fish and Wildlife Service...

  2. Polar bear research in Alaska, spring 1981

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — An investigation of the ecology and population dynamics of Alaskan polar bears has continued since 1967. As part of that program, U.S. Fish and Wildlife Service...

  3. Bearings for the HFIR control plates

    International Nuclear Information System (INIS)

    Recent accelerated wear of HFIR bearings seems to be a more advanced stage of the situation encountered in 1967. The latest observations are in agreement with the hypothesis that high-frequency impact loads at a 300 angle on these bearings are the apparent basic cause of their short life. In view of the limited possibilities for change at this stage of HFIR operation, the region of best payoff seems to be an increase in the load-carrying area at some acceptable sacrifice of low rolling friction. On this basis three types of bearings are proposed for test--two of these are journal types and one is a slider type. The next planned shutdown for major parts replacement provides an opportunity to test these modified bearing types in the HFIR under full mechanical operating conditions but without nuclear operation. The program is recommended for consideration and adoption. (U.S.)

  4. The polar bear and its protection

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — No census has been made of the polar bear population and indeed the general movements of the animals within their range are poorly known. At present it is not...

  5. Ceramic Rail-Race Ball Bearings

    Science.gov (United States)

    Balzer, Mark A.; Mungas, Greg S.; Peters, Gregory H.

    2010-01-01

    Non-lubricated ball bearings featuring rail races have been proposed for use in mechanisms that are required to function in the presence of mineral dust particles in very low-pressure, dry environments with extended life. Like a conventional ball bearing, the proposed bearing would include an inner and an outer ring separated by balls in rolling contact with the races. However, unlike a conventional ball bearing, the balls would not roll in semi-circular or gothic arch race grooves in the rings: instead, the races would be shaped to form two or more rails (see figure). During operation, the motion of the balls would push dust particles into the spaces between the rails where the particles could not generate rolling resistance for the balls

  6. Bear Lake-Minidoka - Phragmites Control

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Bear Lake: Phragmites patches were sprayed on the refuge & north of the lake proper. Minidoka: patches along the Snake River & Lake Walcott were treated...

  7. Cavitation Peening of Aerospace Bearings Project

    Data.gov (United States)

    National Aeronautics and Space Administration — High-value bearings are a critical part of the safety, reliability, cost and performance of modern aircraft. A typical passenger jet will have 100 to 175 high-valve...

  8. Mercury biomagnification in polar bears ( Ursus maritimus)

    Science.gov (United States)

    Horton, T. W.; Blum, J. D.; Xie, Z.; Hren, M.; Chamberlain, C. P.

    2007-12-01

    Mercury biomagnification occurs in a variety of ecosystems resulting in greater potential for toxicological effects in higher-level trophic feeders. However, Hg transport pathways through different foodweb channels are not well known, particularly in high-latitude systems affected by atmospheric Hg deposition associated with snow and ice. Stable carbon and nitrogen isotope ratios and Hg concentrations determined for 26 late 19th and early 20th century polar bear hair specimens collected from cataloged museum collections elucidate relationships between high latitude marine foodweb structure and Hg transport pathways. Nitrogen and carbon isotopic compositions suggest that polar bears derive nutrition from both open water (pelagic) and ice associated (sympagic) foodweb channels. Correlation between Hg concentrations and nitrogen isotope compositions indicate mercury biomagnification occurred in most of the polar bears investigated. Interpretation of stable isotope based foodweb structure in concert with Hg concentrations further suggests that Hg biomagnification occurred to a greater degree in polar bears participating in pelagic foodweb channels.

  9. Telemetry techniques used on Kodiak brown bear

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This report summarizes the results of a study on the techniques used to monitor the movements of Kodiak brown bears instrumented with radio transmitters. Methods...

  10. LIGHT-WEIGHT LOAD-BEARING STRUCTURE

    DEFF Research Database (Denmark)

    2009-01-01

    The invention relates to a light-weight load-bearing structure (1) with optimized compression zone (2), where along one or more compression zones (2) in the structure (1) to be cast a core (3) of strong concrete is provided, which core (3) is surrounded by concrete of less strength (4) compared...... to the core (3) of strong concrete. The invention also relates to a method of casting of light-weight load-bearing structures (1) with optimized compression zone (2) where one or more channels, grooves, ducts, pipes and/or hoses (5) formed in the load-bearing structure (1) serves as moulds for moulding one...... or more cores (3) of strong concrete in the light-weight load-bearing structure (1)....

  11. Failure tests of laminated rubber bearings

    International Nuclear Information System (INIS)

    Three different types of rubber bearing - natural rubber bearing (NRB), lead-rubber bearing (LRB), and high-damping rubber bearing (HRB) - were tested up to failure under various combinations of axial and shear forces. The test results are summarized as follows: 1) Offset shear strain greatly affects tensile behavior and failure. 2) Axial stress or strain does not so greatly affect shear behavior and failure. 3) The characteristics of NBR and LRB are almost independent of strain rate, but those of HRB depend greatly on it. 4) Cyclic loading affects large-deformation behavior and failure to some extent. 5) failure limits which include the interaction between axial stress and shear strain were quantitatively evaluated. 6) A lead plug of LRB has no bad influence on failure. These will be very useful for developing an ultimate response prediction technique, which is necessary to establish rational design philosophy of base isolation systems for FBR plants. (author)

  12. Novel nano bearings constructed by physical adsorption

    Science.gov (United States)

    Zhang, Yongbin

    2015-09-01

    The paper proposes a novel nano bearing formed by the physical adsorption of the confined fluid to the solid wall. The bearing is formed between two parallel smooth solid plane walls sliding against one another, where conventional hydrodynamic lubrication theory predicted no lubricating effect. In this bearing, the stationary solid wall is divided into two subzones which respectively have different interaction strengths with the lubricating fluid. It leads to different physical adsorption and slip properties of the lubricating fluid at the stationary solid wall respectively in these two subzones. It was found that a significant load-carrying capacity of the bearing can be generated for low lubricating film thicknesses, because of the strong physical adsorption and non-continuum effects of the lubricating film.

  13. All Polar Bear Critical Habitat Combined

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This layer shows all categories of polar bear critical habitat combined into one overall polygon. This polygon includes the following critical habitat types: 1)...

  14. Active magnetic bearings used as exciters for rolling element bearing outer race defect diagnosis.

    Science.gov (United States)

    Xu, Yuanping; Di, Long; Zhou, Jin; Jin, Chaowu; Guo, Qintao

    2016-03-01

    The active health monitoring of rotordynamic systems in the presence of bearing outer race defect is considered in this paper. The shaft is assumed to be supported by conventional mechanical bearings and an active magnetic bearing (AMB) is used in the mid of the shaft location as an exciter to apply electromagnetic force to the system. We investigate a nonlinear bearing-pedestal system model with the outer race defect under the electromagnetic force. The nonlinear differential equations are integrated using the fourth-order Runge-Kutta algorithm. The simulation and experimental results show that the characteristic signal of outer race incipient defect is significantly amplified under the electromagnetic force through the AMBs, which is helpful to improve the diagnosis accuracy of rolling element bearing׳s incipient outer race defect. PMID:26803551

  15. Flywheel energy storage with superconductor magnetic bearings

    Science.gov (United States)

    Weinberger, Bernard R.; Lynds, Jr., Lahmer; Hull, John R.

    1993-01-01

    A flywheel having superconductor bearings has a lower drag to lift ratio that translates to an improvement of a factor of ten in the rotational decay rate. The lower drag results from the lower dissipation of melt-processed YBCO, improved uniformity of the permanent magnet portion of the bearings, operation in a different range of vacuum pressure from that taught by the art, and greater separation distance from the rotating members of conductive materials.

  16. Silicon Nitride Balls For Cryogenic Bearings

    Science.gov (United States)

    Butner, Myles F.; Ng, Lillian W.

    1990-01-01

    Resistance to wear greater than that of 440C steel. Experiments show lives of ball bearings immersed in liquid nitrogen or liquid oxygen increased significantly when 440C steel balls (running on 440C steel races) replaced by balls of silicon nitride. Developed for use at high temperatures, where lubrication poor or nonexistent. Best wear life of any bearing tested to date and ball material spalls without fracturing. Plans for future tests call for use of liquid oxygen as working fluid.

  17. Recycling of heat discharged from bearing quenching

    Institute of Scientific and Technical Information of China (English)

    WEN Xin-lin; CI Tie-jun; WEN Peng; ZHANG Rong-ying

    2006-01-01

    In this paper,the technical method of cooling quench medium with air-cooler in the process of bearing quenching is introduced.The exhausted hot air is directly used to dry bearing balls.It is a novel approach for full utilization of heat energy during heat treatment,which increased 30% of the heat efficiency when compared with normal air-cooler methods that directly put exhaust air into atmosphere.

  18. Partial Lubrification of Full Cylindrical Bearings

    OpenAIRE

    Capriz, Gianfranco; Cimatti, Giovanni

    1981-01-01

    the phenomenon of cavitation in bearings is often studied under the assumption that the pressure and the pressure gradient both vanish along the unknown boundary of the cavitation bubble. However, such conditions (often namend after Swift and Stieber) may be inconsistent with mass conservation. The discrepancy is particularly striking when the case of long bearings is studied within the so called Sommerfeld approximation. Therefore a complete analysis of the Sommerfeld case is carried out her...

  19. Surface layer characterisation of bearing rings

    OpenAIRE

    S.J. Skrzypek; M. Goły

    2007-01-01

    austenite. Theoretical calculation of residual macro-stresses due to volume fraction of transformed austenite in bearing rings and following measurements of residual stresses were carried out as well. The bearing elements were made of 100Cr6 steel and they were smoothed and grinded.Design/methodology/approach: Particular features of diffraction patterns like angle position; shape and intensity are used to characterize phase composition, residual micro and macro-stresses, crystallographic tex...

  20. Spectral properties and identification of aerostatic bearings

    Institute of Scientific and Technical Information of China (English)

    Jan Kozánek; Ladislav P(u)st

    2011-01-01

    Modified rotor kit BentlyNevada was used for dynamic characteristics measurements of new developed aerostatic bearings. Mathematical model of these bearings is considered as linear. Model was identified with the help of harmonic force excitation independently from the speed of journal rotation. The stiffness and damping matrices were identified for different air inlet pressures. The calculated spectral properties allow to determine the stability boundary for suitable variation of model parameters.

  1. Design of bearing structures of dwelling - house

    OpenAIRE

    Sodja, Urška

    2007-01-01

    Graduation thesis represents design of bearing structures of dwelling-house including materials and materials´ properties of bearing structures. Self weight, imposed load, snow, and wind are determinated regarding EC1. Static calculation of building is divided to design of timber, reinforced concrete elements and control of resistance of walls. Summary contains earthquake rules for simple masonry buildings. Enclosure contains plans for positions of slaps and reinforces.

  2. Rotordynamics and bearing design of turbochargers

    Science.gov (United States)

    Chen, Wen Jeng

    2012-05-01

    Turbochargers have gained significant attention in recent years. They are already widely used in automotive, locomotive, and marine applications with diesel engines. They are also applied in the aerospace application to increase the engine performance now. The turbochargers used in automotive and aerospace industry are very light-weight with operating speeds above 100,000 rpm. The turbochargers used in locomotive and marine applications are relatively heavy in size and power compared to the automotive and aerospace applications, and the maximum continuous operating speeds are around 30,000 rpm depending on the diesel engine power rating. Floating ring bushings, semi-floating dampers, ball bearings, and ball bearings with dampers are commonly used in automotive applications for small turbochargers. However, these bearings may not be appropriate for large turbochargers in locomotive and marine applications. Instead, multi-lobed bearings with and without squeeze film dampers are commonly used in these heavy-duty turbochargers. This paper deals with the rotordynamic characteristics of larger turbochargers in locomotive and marine applications. Various bearing designs are discussed. Bearing design parameters are studied and optimal values are suggested. Test results are also presented to support the analytical simulation.

  3. Rolling Bearing Life Prediction, Theory, and Application

    Science.gov (United States)

    Zaretsky, Erwin V.

    2013-01-01

    A tutorial is presented outlining the evolution, theory, and application of rolling-element bearing life prediction from that of A. Palmgren, 1924; W. Weibull, 1939; G. Lundberg and A. Palmgren, 1947 and 1952; E. Ioannides and T. Harris, 1985; and E. Zaretsky, 1987. Comparisons are made between these life models. The Ioannides-Harris model without a fatigue limit is identical to the Lundberg-Palmgren model. The Weibull model is similar to that of Zaretsky if the exponents are chosen to be identical. Both the load-life and Hertz stress-life relations of Weibull, Lundberg and Palmgren, and Ioannides and Harris reflect a strong dependence on the Weibull slope. The Zaretsky model decouples the dependence of the critical shear stress-life relation from the Weibull slope. This results in a nominal variation of the Hertz stress-life exponent. For 9th- and 8th-power Hertz stress-life exponents for ball and roller bearings, respectively, the Lundberg- Palmgren model best predicts life. However, for 12th- and 10th-power relations reflected by modern bearing steels, the Zaretsky model based on the Weibull equation is superior. Under the range of stresses examined, the use of a fatigue limit would suggest that (for most operating conditions under which a rolling-element bearing will operate) the bearing will not fail from classical rolling-element fatigue. Realistically, this is not the case. The use of a fatigue limit will significantly overpredict life over a range of normal operating Hertz stresses. Since the predicted lives of rolling-element bearings are high, the problem can become one of undersizing a bearing for a particular application.

  4. Mass Loss Rates of Fasting Polar Bears.

    Science.gov (United States)

    Pilfold, Nicholas W; Hedman, Daryll; Stirling, Ian; Derocher, Andrew E; Lunn, Nicholas J; Richardson, Evan

    2016-01-01

    Polar bears (Ursus maritimus) have adapted to an annual cyclic regime of feeding and fasting, which is extreme in seasonal sea ice regions of the Arctic. As a consequence of climate change, sea ice breakup has become earlier and the duration of the open-water period through which polar bears must rely on fat reserves has increased. To date, there is limited empirical data with which to evaluate the potential energetic capacity of polar bears to withstand longer fasts. We measured the incoming and outgoing mass of inactive polar bears (n = 142) that were temporarily detained by Manitoba Conservation and Water Stewardship during the open-water period near the town of Churchill, Manitoba, Canada, in 2009-2014. Polar bears were given access to water but not food and held for a median length of 17 d. Median mass loss rates were 1.0 kg/d, while median mass-specific loss rates were 0.5%/d, similar to other species with high adiposity and prolonged fasting capacities. Mass loss by unfed captive adult males was identical to that lost by free-ranging individuals, suggesting that terrestrial feeding contributes little to offset mass loss. The inferred metabolic rate was comparable to a basal mammalian rate, suggesting that while on land, polar bears can maintain a depressed metabolic rate to conserve energy. Finally, we estimated time to starvation for subadults and adult males for the on-land period. Results suggest that at 180 d of fasting, 56%-63% of subadults and 18%-24% of adult males in this study would die of starvation. Results corroborate previous assessments on the limits of polar bear capacity to withstand lengthening ice-free seasons and emphasize the greater sensitivity of subadults to changes in sea ice phenology. PMID:27617359

  5. A circumpolar monitoring framework for polar bears

    Science.gov (United States)

    Vongraven, Dag; Aars, Jon; Amstrup, S.; Atkinson, Stephen N.; Belikov, Stanislav; Born, Erik W.; DeBruyn, T.D.; Derocher, Andrew E.; Durner, George M.; Gill, Mike; Lunn, Nicholas J.; Obbard, Martyn E.; Omelak, Jack; Ovsyanikov, Nikita; Peacock, Elizabeth; Richardson, E.E.; Sahanatien, Vicki; Stirling, Ian; Wiig, Øystein

    2012-01-01

    Polar bears (Ursus maritimus) occupy remote regions that are characterized by harsh weather and limited access. Polar bear populations can only persist where temporal and spatial availability of sea ice provides adequate access to their marine mammal prey. Observed declines in sea ice availability will continue as long as greenhouse gas concentrations rise. At the same time, human intrusion and pollution levels in the Arctic are expected to increase. A circumpolar understanding of the cumulative impacts of current and future stressors is lacking, long-term trends are known from only a few subpopulations, and there is no globally coordinated effort to monitor effects of stressors. Here, we describe a framework for an integrated circumpolar monitoring plan to detect ongoing patterns, predict future trends, and identify the most vulnerable polar bear subpopulations. We recommend strategies for monitoring subpopulation abundance and trends, reproduction, survival, ecosystem change, human-caused mortality, human–bear conflict, prey availability, health, stature, distribution, behavioral change, and the effects that monitoring itself may have on polar bears. We assign monitoring intensity for each subpopulation through adaptive assessment of the quality of existing baseline data and research accessibility. A global perspective is achieved by recommending high intensity monitoring for at least one subpopulation in each of four major polar bear ecoregions. Collection of data on harvest, where it occurs, and remote sensing of habitat, should occur with the same intensity for all subpopulations. We outline how local traditional knowledge may most effectively be combined with the best scientific methods to provide comparable and complementary lines of evidence. We also outline how previously collected intensive monitoring data may be sub-sampled to guide future sampling frequencies and develop indirect estimates or indices of subpopulation status. Adoption of this framework

  6. 24 CFR 3285.202 - Soil classifications and bearing capacity.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 5 2010-04-01 2010-04-01 false Soil classifications and bearing... Soil classifications and bearing capacity. The soil classification and bearing capacity of the soil... bearing capacity must be determined by one or more of the following methods, unless the soil...

  7. 46 CFR 61.20-23 - Tailshaft clearance; bearing weardown.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Tailshaft clearance; bearing weardown. 61.20-23 Section...; bearing weardown. (a) Water lubricated bearings, other than rubber, must be rebushed as follows: (1) Where the propelling machinery is located amidship, the after stern tube bearing must be rebushed when it...

  8. Noise reduction of rotating machinery by viscoelastic bearing supports

    NARCIS (Netherlands)

    Tillema, Hetzer Gido

    2003-01-01

    The demand for silent rolling bearing applications, such as electric motors and gearboxes, has resulted in an investigation of viscoelastic bearing supports. By placing a thin viscoelastic layer between the bearing outer ring and the surrounding structure, vibrations of the shaft-bearing arrangement

  9. Wear numbers for ball cup and journal bearings

    NARCIS (Netherlands)

    Ligterink, D.J.; Moes, H.

    1980-01-01

    A wear number is defined for ball cup bearings and for journal bearings where the cup and the cylindrical bearing are made of soft material. This dimensionless wear number provides a relation between the following five quantities: the radius of the ball or the length of the journal bearing in millim

  10. 49 CFR 230.102 - Tender plain bearing journal boxes.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender plain bearing journal boxes. 230.102... Locomotives and Tenders Running Gear § 230.102 Tender plain bearing journal boxes. Plain bearing journal boxes... expected to damage the bearing; or have a detrimental effect on the lubrication of the journal and...

  11. Bearing assemblies, apparatuses, and motor assemblies using the same

    Science.gov (United States)

    Sexton, Timothy N.; Cooley, Craig H.; Knuteson, Cody W.

    2015-12-29

    Various embodiments of the invention relate to bearing assemblies, apparatuses and motor assemblies that include geometric features configured to impart a selected amount of heat transfer and/or hydrodynamic film formation. In an embodiment, a bearing assembly may include a plurality of superhard bearing pads distributed circumferentially about an axis. At least some of the plurality of superhard bearing pads may include a plurality of sub-superhard bearing elements defining a bearing surface. At least some of the plurality of sub-superhard bearing elements may be spaced from one another by one or more voids to impart a selected amount of heat transfer and hydrodynamic film formation thereon during operation. The bearing assembly may also include a support ring that carries the plurality of superhard bearing pads. In addition, at least a portion of the sub-superhard bearing elements may extend beyond the support ring.

  12. Severity estimation of cracked shaft vibrations within fluid film bearings

    Science.gov (United States)

    Prabhu, B. S.; Sekhar, A. S.

    1995-07-01

    The equations of motion, with four degrees of freedom, taking into consideration the flexibility, damping and cross coupling of the fluid film bearings are derived for a cracked Jeffcott rotor supported on fluid film bearings. Dimensionless equations are developed for dynamic radial load, dynamic pressure developed in the fluid film bearings and coefficient of dissipation considering the journal vibrations in two harmonics; bearing fluid film stiffness and damping coefficients. These are applied to a cracked Jeffcott rotor supported on different types of bearings, i.e., cylindrical journal bearings, offset cylindrical bearings, tilting pad journal bearings and three-lobe bearings. Based on the allowable dynamic pressure developed in the fluid bearings, the severity of cracked shaft and allowable crack depths are estimated in this study. Measurement of dynamic pressure and dissipation for monitoring the crack growth is suggested. However, 2x vibration is the best indicator of cracks in the shafts.

  13. Rotor-Bearing System Stability Performance Comparing Hybrid versus Conventional Bearings

    Directory of Open Access Journals (Sweden)

    Gomez-Mancilla Julio

    2005-01-01

    Full Text Available New closed-form expressions for calculating the linear stability thresholds for rigid and flexible Jeffcott systems and the imbalance response for a rotor supported on a hybrid bearing are presented. For typical bearings characteristics, expressions yield stability thresholds practically equal to those reported by Lund (1966. The hybrid bearing design has a single injection port whose location is so chosen to stabilize the bearing performance and to reduce the steady equilibrium attitude angle. Rotordynamics coefficients graphs for conventional and pressurized bearings, as functions of bearing equilibrium eccentricity and/or Sommerfeld number, are presented. Using the rotordynamics coefficients into the expressions for the corresponding velocity thresholds and the imbalance response, the system stability and vibration performances are estimated and analyzed. When comparing the Jeffcott flexible shaft supported on two journal bearings of the conventional type with the hybrid type, the results show a clear superiority of the pressurized design as far as stability behavior is concerned. Specifically for cases of flexible shafts with similar characteristics to those used in industry, the analysis shows that this design yields velocity thresholds 25%–40% higher compared to the conventional circular ones. Also this bearing displays nonlinear feeding pressure behavior, and it is capable of reducing the synchronous vibration amplitude in most speed ranges, except around the critical speed; moreover, for certain Jeffcott configurations the amplitude reduction can be substantial.

  14. Nonlinear vibrations and stability of aerostatic bearing

    Directory of Open Access Journals (Sweden)

    Kozánek J.

    2008-12-01

    Full Text Available Bearings based on aerostatic principle belong to the new machine elements advantageous for low- and high-speed applications, but their dynamic and stability properties are not yet sufficiently known. This paper presents a new elaborated method and gained results of theoretical investigation of dynamic properties of aerostatic bearing in general dimensionless form. It is aimed also as a supporting tool for diagnostic and identification methods used at developing of new bearings proposed by TECHLAB, Prague for industrial applications. Mathematical model expresses nonlinear and evolutive properties in the entire area of bearing clearance, contains sufficient number of free parameters in functions of restoring and damping forces and can therefore describe all types of motions occurring in gas bearings as periodic, quasi-periodic, including beats and instability, which can leads to chaotic and self-excited vibrations. The influence of non-diagonal elements of stiffness and damping matrices of linearized model on the spectral properties and the stability of system is investigated, too.

  15. 77 FR 59639 - Bear Lake National Wildlife Refuge, Bear Lake County, ID and Oxford Slough Waterfowl Production...

    Science.gov (United States)

    2012-09-28

    ... notice in the Federal Register (75 FR 35829; June 23, 2010). Bear Lake National Wildlife Refuge Bear Lake... Fish and Wildlife Service Bear Lake National Wildlife Refuge, Bear Lake County, ID and Oxford Slough... our draft comprehensive conservation plan and environmental assessment (Draft CCP/EA) for the...

  16. Fatigue Life Analysis of Rolling Bearings Based on Quasistatic Modeling

    OpenAIRE

    Wei Guo; Hongrui Cao; Zhengjia He; Laihao Yang

    2015-01-01

    Rolling bearings are widely used in aeroengine, machine tool spindles, locomotive wheelset, and so forth. Rolling bearings are usually the weakest components that influence the remaining life of the whole machine. In this paper, a fatigue life prediction method is proposed based on quasistatic modeling of rolling bearings. With consideration of radial centrifugal expansion and thermal deformations on the geometric displacement in the bearings, the Jones’ bearing model is updated, which can pr...

  17. An Advanced Microturbine System with Water-Lubricated Bearings

    OpenAIRE

    Susumu Nakano; Tadaharu Kishibe; Tomoaki Inoue; Hiroyuki Shiraiwa

    2009-01-01

    A prototype of the next-generation, high-performance microturbine system was developed for laboratory evaluation. Its unique feature is its utilization of water. Water is the lubricant for the bearings in this first reported application of water-lubricated bearings in gas turbines. Bearing losses and limitations under usage conditions were found from component tests done on the bearings and load tests done on the prototype microturbine. The rotor system using the water-lubricated bearings ach...

  18. ES and H-compatible lubrication for duplex bearings

    Energy Technology Data Exchange (ETDEWEB)

    Steinhoff, R.G.

    1997-10-01

    Two ES and H-compatible lubricants (environment, safety, and health) for duplex bearing applications and one hybrid material duplex bearing were evaluated and compared against duplex bearings with trichlorotrifluoroethane (Freon) deposition of low molecular weight polytetrafluoroethylene (PTFE) bearing lubricant extracted from Vydax{trademark}. Vydax is a product manufactured by DuPont consisting of various molecular weights of PTFE suspended in trichlorotrifluoroethane (Freon), which is an ozone-depleting solvent. Vydax has been used as a bearing lubricant in strong link mechanisms since 1974. Hybrid duplex bearings with silicon nitride balls and molded glass-nylon-Teflon retainers, duplex bearings lubricated with sputtered MoS{sub 2} on races and retainers, and duplex bearings lubricated with electrophoretic deposited MoS{sub 2} were evaluated. Bearings with electrophoretic deposited MoS{sub 2} performed as well as bearings with Freon deposition of PTFE from Freon-based Vydax. Hybrid bearings with silicon nitride balls performed worse than bearings lubricated with Vydax, but their performance would still be acceptable for most applications. Bearings lubricated with sputtered MoS{sub 2} on the races and retainers had varying amounts of film on the bearings. This affected the performance of the bearings. Bearings with a uniform coating performed to acceptable levels, but bearings with no visible MoS{sub 2} on the races and retainers did not perform as well as bearings with the other coatings. Unless process controls are incorporated in the sputtering process or the bearings are screened, they do not appear to be acceptable for duplex bearing applications.

  19. Removable bearing arrangement for a wind turbine generator

    Science.gov (United States)

    Bagepalli, Bharat Sampathkumaran; Jansen, Patrick Lee; Gadre, Aniruddha Dattatraya

    2010-06-15

    A wind generator having removable change-out bearings includes a rotor and a stator, locking bolts configured to lock the rotor and stator, a removable bearing sub-assembly having at least one shrunk-on bearing installed, and removable mounting bolts configured to engage the bearing sub-assembly and to allow the removable bearing sub-assembly to be removed when the removable mounting bolts are removed.

  20. Oxford phase III meniscal bearing fracture: case report.

    Science.gov (United States)

    Lim, Hong-Chul; Shon, Won-Yong; Kim, Seung-Ju; Bae, Ji-Hoon

    2014-01-01

    Meniscal bearing fracture is a rare complication of phase III Oxford unicompartmental knee replacement (UKR). We report a case of a meniscal bearing fracture that occurred 7 years after phase III Oxford medial UKR. The meniscal bearing showed uneven delamination of the polyethylene in the thinnest articular surface and an impingement lesion. This lesion initiated a fatigue crack that propagated to cause failure of the meniscal bearing. This is the first report of a meniscal bearing fracture without a posterior marker wire.

  1. Noise reduction of rotating machinery by viscoelastic bearing supports

    OpenAIRE

    Tillema, Hetzer Gido

    2003-01-01

    The demand for silent rolling bearing applications, such as electric motors and gearboxes, has resulted in an investigation of viscoelastic bearing supports. By placing a thin viscoelastic layer between the bearing outer ring and the surrounding structure, vibrations of the shaft-bearing arrangement can be isolated and damped in such a way that the radiated sound power is reduced. The ultimate goal of this research was to develop a design strategy for viscoelastic bearing supports resulting i...

  2. Wear numbers for ball cup and journal bearings

    OpenAIRE

    Ligterink, D.J.; Moes, H.

    1980-01-01

    A wear number is defined for ball cup bearings and for journal bearings where the cup and the cylindrical bearing are made of soft material. This dimensionless wear number provides a relation between the following five quantities: the radius of the ball or the length of the journal bearing in millimetres, the wear modulus in newtons per square millimetre, the maximum wear depth rate of the cup or the cylindrical bearing in millimetres per second, the force between the mating surfaces in newto...

  3. Aerial strip surveys of polar bears in the Barents Sea

    OpenAIRE

    Wiig, Øystein; Bakken, Vidar

    1990-01-01

    Aerial strip surveys of polar bears in the Barents Sea were performed by helicopter in winter 1987. The number of bears within 100 m on each side of the helicopter was counted. A total of 263.6 km2 was surveyed and 21 bears were counted. Most of the bears were found in the southern part of the area, which indicates that the southwestern ice edge area in the Barents Sea is a very important winter habitat for polar bears.

  4. Bearing tester data compilation, analysis and reporting and bearing math modeling, volume 1

    Science.gov (United States)

    Marshall, D. D.; Montgomery, E. E.; New, L. S.; Stone, M. A.; Tiller, B. K.

    1984-01-01

    Thermal and mechanical models of high speed angular contact ball bearings operating in LOX and LN2 were developed and verified with limited test data in an effort to further understand the parameters that determine or effect the SSME turbopump bearing operational characteristics and service life. The SHABERTH bearing analysis program which was adapted to evaluate shaft bearing systems in cryogenics is not capable of accommodating varying thermal properties and two phase flow. A bearing model with this capability was developed using the SINDA thermal analyzer. Iteration between the SHABERTH and the SINDA models enable the establishment of preliminary bounds for stable operation in LN2. These limits were established in terms of fluid flow, fluid inlet temperature, and axial load for a shaft speed of 30,000 RPM.

  5. Synthesis, Crystal Structure and Thermal Stability of a Saturated Dimeric Ce(Ⅲ)-chelated Complex Based on Benzoate and 1,10-Phenanthroline Ligands

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The title complex, [Ce(BA)3phen]2 (BA = benzoate, phen = 1,10-phenanthroline),was prepared by the reaction of Ce(NO3)3·6H2O, benzoic acid and 1,10-phenanthroline. The complex was characterized by single-crystal X-ray diffraction, elemental analysis, IR spectra and TG-DTG techniques. The results show that the crystal is of triclinic, space group P(1) with a =10.912(2), b = 11.962(3), c = 12.474(3)(A), a = 104.889(3), β = 93.523(3), γ = 113.332(3)°,C66H46Ce2N4O12, Mr = 1366.90, V= 1420.2(6) (A)3, Z = 1, Dc = 1.598 g/cm3,μ = 1.652 mm-1, S =1.024 and F(000) = 682. The final R = 0.0391 and wR = 0.0947 for 4878 observed reflections with I > 2σ(1). The structure of the title complex consists of two Ce(C6H5COO)3(C12H8N2) units,forming a binuclear molecule. Each Ce(Ⅲ) is coordinated by two O atoms of one bidentate chelating carboxylate group, five O atoms of two bidentate bridging and two tridentate chelating-bridging carboxylate groups, and two N atoms of one 1,10-phenanthroline molecule to complete a distorted monocapped square antiprism geometry. Its thermogravimetric analysis was determined by TG-DTG techniques.

  6. Effect of timing of oestradiol benzoate injection relative to gonadotropin treatment on superovulatory response, and on embryo yield and quality in beef heifers.

    Science.gov (United States)

    Yaakub, H; Duffy, P; O'Callaghan, D; Boland, M P

    1998-09-11

    Variation in superovulatory responses in cattle may be related to the stage of follicular growth at the time of gonadotropin treatment. Waves of follicle growth are regulated by both follicle-stimulating hormone (FSH) and oestradiol. The objective of experiment 1 was to determine the dynamics of follicle wave emergence and the relationship with FSH and oestradiol concentrations, after treatment of heifers with oestradiol benzoate (ODB) in the presence of an intravaginal progesterone-releasing device (CIDR-B). Experiment 2 examined the superovulatory response, embryo yield and quality following treatment with porcine follicle-stimulating hormone (pFSH) at different times relative to ODB injection. In experiment 1, 28 beef heifers were treated with a CIDR for 9 days and allocated at random to one of four groups to receive either: (I) CIDR only, or 5 mg ODB given as a single intramuscular injection at (II) day 0 (d0); (III) day 1.5 (d1.5); or (IV) day 3 (d3) post CIDR insertion. Ovaries were examined using daily ultrasound and blood samples were collected twice daily for 11 days. In experiment 2, 96 heifers were treated with a CIDR and 5 mg ODB as in experiment 1, and were allocated using a 4 x 3 factorial design plan to a superovulation programme using three doses (400 IU; 600 IU; 800 IU) of pFSH. FSH was given for 4 days at 12-h intervals beginning 6.5 days after CIDR insertion. Heifers received prostaglandin analogue 12 h before CIDR removal and were inseminated (AI) at 48 and 60 h post CIDR withdrawal and embryos were recovered 7 days after AI. In experiment 1, the interval from CIDR insertion to follicle wave emergence (FWE) was longer (P 0.05) from heifers treated at d0 (14.4 +/- 2.0) or with CIDR only (15.0 +/- 1.8). There were fewer (P quality following superovulation. PMID:9783992

  7. Biological effects of the anti-parasitic chemotherapeutant emamectin benzoate on a non-target crustacean, the spot prawn (Pandalus platyceros Brandt, 1851) under laboratory conditions

    Energy Technology Data Exchange (ETDEWEB)

    Veldhoen, Nik [Department of Biochemistry and Microbiology, University of Victoria, P.O. Box 3055, Stn CSC, Victoria, BC, V8W 3P6 (Canada); Ikonomou, Michael G. [Institute of Ocean Sciences, Fisheries and Oceans Canada, 9860 West Saanich Road, P.O. Box 6000, Sidney, BC, V8L 4B2 (Canada); Buday, Craig [Pacific Environmental Science Centre, Environment Canada, 2645 Dollarton Highway, North Vancouver, BC, V7H 1V2 (Canada); Jordan, Jameson; Rehaume, Vicki; Cabecinha, Melissa [Department of Biochemistry and Microbiology, University of Victoria, P.O. Box 3055, Stn CSC, Victoria, BC, V8W 3P6 (Canada); Dubetz, Cory; Chamberlain, Jon [Institute of Ocean Sciences, Fisheries and Oceans Canada, 9860 West Saanich Road, P.O. Box 6000, Sidney, BC, V8L 4B2 (Canada); Pittroff, Sabrina; Vallee, Kurtis [Department of Biochemistry and Microbiology, University of Victoria, P.O. Box 3055, Stn CSC, Victoria, BC, V8W 3P6 (Canada); Aggelen, Graham van [Pacific Environmental Science Centre, Environment Canada, 2645 Dollarton Highway, North Vancouver, BC, V7H 1V2 (Canada); Helbing, Caren C., E-mail: chelbing@uvic.ca [Department of Biochemistry and Microbiology, University of Victoria, P.O. Box 3055, Stn CSC, Victoria, BC, V8W 3P6 (Canada)

    2012-02-15

    The potential impact of commercial salmon aquaculture along the coast of British Columbia on the health of non-target marine wildlife is of growing concern. In the current initiative, the biological effects on gene expression within spot prawn (Pandalus platyceros) exposed to the sea lice controlling agent, emamectin benzoate (EB; 0.1-4.8 mg/kg sediment), were investigated. A mean sediment/water partitioning coefficient (K{sub p}) was determined to be 21.81 and significant levels of EB were detected in the tail muscle tissue in all exposed animals. Animals selected for the experiment did not have eggs and were of similar weight. Significant mortality was observed within 8 days of EB treatment at concentrations between 0.1 and 0.8 mg/kg and there was no effect of EB on molting. Twelve spot prawn cDNA sequences were isolated from the tail muscle either by directed cloning or subtractive hybridization of control versus EB exposed tissues. Three of the transcripts most affected by EB exposure matched sequences encoding the 60S ribosomal protein L22, spliceosome RNA helicase WM6/UAP56, and the intracellular signal mediator histidine triad nucleotide binding protein 1 suggesting that translation, transcription regulation, and apoptosis pathways were impacted. The mRNA encoding the molting enzyme, {beta}-N-acetylglucosaminidase, was not affected by EB treatment. However, the expression of this transcript was extremely variable making it unsuitable for effects assessment. The results suggest that short-term exposure to EB can impact biological processes within this non-target crustacean.

  8. Synergistic Potentiation of Cystic Fibrosis Transmembrane Conductance Regulator Gating by Two Chemically Distinct Potentiators, Ivacaftor (VX-770) and 5-Nitro-2-(3-Phenylpropylamino) Benzoate.

    Science.gov (United States)

    Lin, Wen-Ying; Sohma, Yoshiro; Hwang, Tzyh-Chang

    2016-09-01

    Cystic fibrosis (CF) is caused by loss-of-function mutations of the cystic fibrosis transmembrane conductance regulator (CFTR) gene encoding a phosphorylation-activated but ATP-gated chloride channel. Previous studies suggested that VX-770 [ivacaftor, N-(2,4-di-tert-butyl-5-hydroxyphenyl)-4-oxo-1,4-dihydroquinoline-3-carboxamide], a CFTR potentiator now used in clinics, increases the open probability of CFTR by shifting the gating conformational changes to favor the open channel configuration. Recently the chloride channel blocker and CFTR potentiator 5-nitro-2-(3-phenylpropylamino) benzoate (NPPB) has been reported to enhance CFTR activity by a mechanism that exploits the ATP hydrolysis-driven, nonequilibrium gating mechanism unique to CFTR. Surprisingly however, NPPB increased the activity of nonhydrolytic G551D-CFTR, the third most common disease-associated mutation. Here, we further investigated the mechanism of NPPB's effects on CFTR gating by assessing its interaction with well-studied VX-770. Interestingly, once G551D-CFTR was maximally potentiated by VX-770, NPPB further increased its activity. However, quantitative analysis of this drug-drug interaction suggests that this pharmacologic synergism is not due to independent actions of NPPB and VX-770 on CFTR gating; instead, our data support a dependent mechanism involving two distinct binding sites. This latter idea is further supported by the observation that the locked-open time of a hydrolysis-deficient mutant K1250A was shortened by NPPB but prolonged by VX-770. In addition, the effectiveness of NPPB, but not of VX-770, was greatly diminished in a mutant whose second nucleotide-binding domain was completely removed. Interpreting these results under the framework of current understanding of CFTR gating not only reveals insights into the mechanism of action for different CFTR potentiators but also brings us one step forward to a more complete schematic for CFTR gating. PMID:27413118

  9. Structural and spectroscopic characterization of 1-(diaminomethylene) thiouron-1-ium benzoate and bis(1-(diaminomethylene)thiouron-1-ium) phthalate trihydrate

    Science.gov (United States)

    Perpétuo, Genivaldo Julio; Janczak, Jan

    2016-02-01

    Two single crystals of 1-(diaminomethylene) thiouron-1-ium benzoate (1) and bis(1-(diaminomethylene)thiouron-1-ium) phthalate trihydrate (2) were grown using a solution growth technique. The compound 1 crystallises in the centrosymmetric P21/c space group of the monoclinic system, whereas the compound 2 in the centrosymmetric Pbcn space group of orthorhombic system. The solid-state organisation of 1 and 2 has been analysed with respect to cation-anion and hydrogen bonding interactions. The oppositely charged units interact via almost linear hydrogen bonds with the graphs of R22(8) and R21(6) forming molecular complexes. In the crystal 1 the R22(8) motif is formed by donation to the carboxylate group from amine group joined to C1 and from imine group and R21(6) motif is formed by donation to the O2 from amine group joined to C2 and from imine group, whereas in crystal 2 the graphs are formed oppositely. Interactions between the hydrogen-bonded molecular complexes in 1 lead to formation of layered 2D structure, whereas in 2, due to presence of hydrated water molecules lead to formation of 3D hydrogen-bonded supramolecular network. The obtained deuterated analogues of 1 and 2 crystallise similar as H-compound in the monoclinic and orthorhombic system with quite similar lattice parameters. The compounds were also characterised by the FT-IR and Raman spectroscopies. The characteristic bands of the functional and skeletal groups are discussed.

  10. Food additives such as sodium sulphite, sodium benzoate and curcumin inhibit leptin release in lipopolysaccharide-treated murine adipocytes in vitro.

    Science.gov (United States)

    Ciardi, Christian; Jenny, Marcel; Tschoner, Alexander; Ueberall, Florian; Patsch, Josef; Pedrini, Michael; Ebenbichler, Christoph; Fuchs, Dietmar

    2012-03-01

    Obesity leads to the activation of pro-inflammatory pathways, resulting in a state of low-grade inflammation. Recently, several studies have shown that the exposure to lipopolysaccharide (LPS) could initiate and maintain a chronic state of low-grade inflammation in obese people. As the daily intake of food additives has increased substantially, the aim of the present study was to investigate a potential influence of food additives on the release of leptin, IL-6 and nitrite in the presence of LPS in murine adipocytes. Leptin, IL-6 and nitrite concentrations were analysed in the supernatants of murine 3T3-L1 adipocytes after co-incubation with LPS and the food preservatives, sodium sulphite (SS), sodium benzoate (SB) and the spice and colourant, curcumin, for 24 h. In addition, the kinetics of leptin secretion was analysed. A significant and dose-dependent decrease in leptin was observed after incubating the cells with SB and curcumin for 12 and 24 h, whereas SS decreased leptin concentrations after 24 h of treatment. Moreover, SS increased, while curcumin decreased LPS-stimulated secretion of IL-6, whereas SB had no such effect. None of the compounds that were investigated influenced nitrite production. The food additives SS, SB and curcumin affect the leptin release after co-incubation with LPS from cultured adipocytes in a dose- and time-dependent manner. Decreased leptin release during the consumption of nutrition-derived food additives could decrease the amount of circulating leptin to which the central nervous system is exposed and may therefore contribute to an obesogenic environment. PMID:21801469

  11. Cinnamon and Its Metabolite Sodium Benzoate Attenuate the Activation of p21rac and Protect Memory and Learning in an Animal Model of Alzheimer's Disease.

    Directory of Open Access Journals (Sweden)

    Khushbu K Modi

    Full Text Available This study underlines the importance of cinnamon, a commonly used natural spice and flavoring material, and its metabolite sodium benzoate (NaB in attenuating oxidative stress and protecting memory and learning in an animal model of Alzheimer's disease (AD. NaB, but not sodium formate, was found to inhibit LPS-induced production of reactive oxygen species (ROS in mouse microglial cells. Similarly, NaB also inhibited fibrillar amyloid beta (Aβ- and 1-methyl-4-phenylpyridinium(+-induced microglial production of ROS. Although NaB reduced the level of cholesterol in vivo in mice, reversal of the inhibitory effect of NaB on ROS production by mevalonate, and geranylgeranyl pyrophosphate, but not cholesterol, suggests that depletion of intermediates, but not end products, of the mevalonate pathway is involved in the antioxidant effect of NaB. Furthermore, we demonstrate that an inhibitor of p21rac geranylgeranyl protein transferase suppressed the production of ROS and that NaB suppressed the activation of p21rac in microglia. As expected, marked activation of p21rac was observed in the hippocampus of subjects with AD and 5XFAD transgenic (Tg mouse model of AD. However, oral feeding of cinnamon (Cinnamonum verum powder and NaB suppressed the activation of p21rac and attenuated oxidative stress in the hippocampus of Tg mice as evident by decreased dihydroethidium (DHE and nitrotyrosine staining, reduced homocysteine level and increased level of reduced glutathione. This was accompanied by suppression of neuronal apoptosis, inhibition of glial activation, and reduction of Aβ burden in the hippocampus and protection of memory and learning in transgenic mice. Therefore, cinnamon powder may be a promising natural supplement in halting or delaying the progression of AD.

  12. Ovarian dynamics in response to two modified intravaginal progesterone releasing device and oestradiol benzoate based ovulation synchronisation protocols designed for use in Brahman heifers.

    Science.gov (United States)

    Edwards, S A A; Atkinson, P C; Satake, N; Boe-Hansen, G; McGowan, M R

    2014-07-01

    The objective was to investigate the ovarian response of Brahman heifers to two modified ovulation synchronisation protocols developed to increase the proportion of normal synchronous ovulations. Experiment 1 characterised the growth of the ovulatory follicle in heifers (n=19) treated with an intravaginal progesterone releasing device (IPRD) and oestradiol benzoate (ODB), to determine the optimal time to induce ovulation. Using the findings from Experiment 1, Experiment 2 investigated the effect of reducing the duration of IPRD insertion and increasing the interval from IPRD removal to ODB treatment (modified protocol 1 - OPO-6; n=20), and omitting ODB treatment at the time of IPRD insertion (modified protocol 2 - PO-6; n=20). An IPRD (0.78 g progesterone) was inserted at Day 0 (OPO-8) or Day 2 (OPO-6 and PO-6) and all heifers also received 1 mg ODB i.m. Day 8: IPRD removed + 500 μg cloprostenol i.m. At 24 h (OPO-8) and 36 h (OPO-6 and PO-6) post IPRD removal: 1 mg ODB i.m. Fixed-time AI (FTAI) occurred at 54 h for OPO-8 and 72 h for OPO-6 and PO-6, post IPRD removal. After IPRD treatment all OPO-6 and OPO-8 heifers initiated a new follicular wave whereas 25% of PO-6 heifers failed. Diameter of the dominant follicle was larger at FTAI in the PO-6 (11.34 ± 0.50 mm) compared to the OPO-8 protocol (9.74 ± 0.51 mm; P<0.05), but similar to the OPO-6 protocol (10.52 ± 0.51 mm). Proportion of ovulations occurring 12 h prior and 24 h post FTAI was similar for the PO-6 (80%) and OPO-6 (75%) protocols but numerically lower in the OPO-8 heifers (60%). The apparent improvement in ovarian response in heifers treated with the modified protocols needs to be confirmed in larger field studies. PMID:24880980

  13. A field investigation of a modified intravaginal progesterone releasing device and oestradiol benzoate based ovulation synchronisation protocol designed for fixed-time artificial insemination of Brahman heifers.

    Science.gov (United States)

    Edwards, S A A; Boe-Hansen, G B; Satake, N; Chandra, K; McGowan, M R

    2015-09-01

    Pregnancy rates (PR) to fixed-time AI (FTAI) in Brahman heifers were compared after treatment with a traditional oestradiol-based protocol (OPO-8) or a modified protocol (OPO-6) where the duration of intravaginal progesterone releasing device (IPRD) was reduced from 8 to 6 days, and the interval from IPRD removal to oestradiol benzoate (ODB) was increased from 24 to 36 h. Rising 2 yo heifers on Farm A: (n = 238 and n = 215; two consecutive days AI); B (n = 271); and C (n = 393) were allocated to OPO-8 or OPO-6. An IPRD was inserted and 1mg ODB i.m. on Day 0 for OPO-8 heifers and Day 2 for OPO-6 heifers. On Day 8, the IPRD was removed and 500 μg cloprostenol i.m. At 24h, for OPO-8 heifers, and 36 h, for OPO-6 heifers, post IPRD removal all heifers received 1mg ODB i.m. FTAI was conducted at 54 and 72 h post IPRD removal for OPO-8 and OPO-6 heifers. At Farm A, OPO-6 heifers, AI on the second day, the PR was 52.4% to FTAI (P = 0.024) compared to 36.8% for OPO-8 heifers. However, no differences were found between OPO-8 and OPO-6 protocols at Farm A (first day of AI) (39.9 vs. 35.7%), or Farms B (26.2 vs. 35.4%) and C (43.2% vs. 40.3%). Presence of a corpus luteum at IPRD insertion affected PR to FTAI (43.9% vs. 28.8%; P < 0.001). This study has shown that the modified ovulation synchronisation protocol OPO-6 may be a viable alternative to the OPO-8 protocol for FTAI in B. indicus heifers. PMID:26282523

  14. Conceptual Design and Feasibility of Foil Bearings for Rotorcraft Engines: Hot Core Bearings

    Science.gov (United States)

    Howard, Samuel A.

    2007-01-01

    Recent developments in gas foil bearing technology have led to numerous advanced high-speed rotating system concepts, many of which have become either commercial products or experimental test articles. Examples include oil-free microturbines, motors, generators and turbochargers. The driving forces for integrating gas foil bearings into these high-speed systems are the benefits promised by removing the oil lubrication system. Elimination of the oil system leads to reduced emissions, increased reliability, and decreased maintenance costs. Another benefit is reduced power plant weight. For rotorcraft applications, this would be a major advantage, as every pound removed from the propulsion system results in a payload benefit.. Implementing foil gas bearings throughout a rotorcraft gas turbine engine is an important long-term goal that requires overcoming numerous technological hurdles. Adequate thrust bearing load capacity and potentially large gearbox applied radial loads are among them. However, by replacing the turbine end, or hot section, rolling element bearing with a gas foil bearing many of the above benefits can be realized. To this end, engine manufacturers are beginning to explore the possibilities of hot section gas foil bearings in propulsion engines. This overview presents a logical follow-on activity by analyzing a conceptual rotorcraft engine to determine the feasibility of a foil bearing supported core. Using a combination of rotordynamic analyses and a load capacity model, it is shown to be reasonable to consider a gas foil bearing core section. In addition, system level foil bearing testing capabilities at NASA Glenn Research Center are presented along with analysis work being conducted under NRA Cooperative Agreements.

  15. Powder metallurgy bearings for advanced rocket engines

    Science.gov (United States)

    Fleck, J. N.; Killman, B. J.; Munson, H.E.

    1985-01-01

    Traditional ingot metallurgy was pushed to the limit for many demanding applications including antifriction bearings. New systems require corrosion resistance, better fatigue resistance, and higher toughness. With conventional processing, increasing the alloying level to achieve corrosion resistance results in a decrease in other properties such as toughness. Advanced powder metallurgy affords a viable solution to this problem. During powder manufacture, the individual particle solidifies very rapidly; as a consequence, the primary carbides are very small and uniformly distributed. When properly consolidated, this uniform structure is preserved while generating a fully dense product. Element tests including rolling contact fatigue, hot hardness, wear, fracture toughness, and corrosion resistance are underway on eleven candidate P/M bearing alloys and results are compared with those for wrought 440C steel, the current SSME bearing material. Several materials which offer the promise of a significant improvement in performance were identified.

  16. Trace fossils in coal-bearing sequences

    Energy Technology Data Exchange (ETDEWEB)

    Pollard, J.E.

    1988-03-01

    In the past decade trace fossils have been recorded extensively from coal-bearing sediments, differing widely in facies, age and location. Westphalian or Stephanian 'coal-measures' in Britain, Europe and Eastern Canada contain an ichnofauna produced by invertebrates and/or vertebrates in upper delta plain sediments. This contrasts with the marine-related lower delta plain ichnofaunas known from Pennsylvanian rocks of the United States and Permian Gondwana 'coal-measures' of South Africa. Deltaic complexes of Middle Jurassic age in the North Sea basin and Upper Cretaceous age in North America contain marine trace fossils and dinosaur footprints in coastal coal- bearing facies. These case histories illustrate the importance of trace fossils both in facies analysis of coal-bearing sequences and in recording the presence of animals rarely known as body fossils in such clastic sediments. 80 refs., 5 figs.

  17. Hydrolyzable polyureas bearing hindered urea bonds.

    Science.gov (United States)

    Ying, Hanze; Cheng, Jianjun

    2014-12-10

    Hydrolyzable polymers are widely used materials that have found numerous applications in biomedical, agricultural, plastic, and packaging industrials. They usually contain ester and other hydrolyzable bonds, such as anhydride, acetal, ketal, or imine, in their backbone structures. Here, we report the first design of hydrolyzable polyureas bearing dynamic hindered urea bonds (HUBs) that can reversibly dissociate to bulky amines and isocyanates, the latter of which can be further hydrolyzed by water, driving the equilibrium to facilitate the degradation of polyureas. Polyureas bearing 1-tert-butyl-1-ethylurea bonds that show high dynamicity (high bond dissociation rate), in the form of either linear polymers or cross-linked gels, can be completely degraded by water under mild conditions. Given the simplicity and low cost for the production of polyureas by simply mixing multifunctional bulky amines and isocyanates, the versatility of the structures, and the tunability of the degradation profiles of HUB-bearing polyureas, these materials are potentially of very broad applications.

  18. The ultimate bearing capacity of ice beams

    Directory of Open Access Journals (Sweden)

    Li Liang

    2013-02-01

    Full Text Available It is usually proposed that bearing capacity of the ice beam during its interaction with a sloping hydraulic structure is exhausted when tensile stresses in the beam’s cross-section reach some limit. But besides the tensile stress there is a compressive stress during the interaction with a sloping structure. This can change our estimations of the ultimate bearing capacity and load exerted on the structure. The purpose of the study was to estimate influence of the longitudinal compressive stress on the ice beam’s ultimate bearing capacity. The solution was obtained with the program complex LS-DYNA. Results of the mathematical modeling were compared with data of physical experiments conducted by Sodhi. Good correlation of the results gave possibility to conduct wide numerical experiments and to suggest corrections to the existing methodology.

  19. Robust bearing estimation for 3-component stations

    Energy Technology Data Exchange (ETDEWEB)

    CLAASSEN,JOHN P.

    2000-02-01

    A robust bearing estimation process for 3-component stations has been developed and explored. The method, called SEEC for Search, Estimate, Evaluate and Correct, intelligently exploits the inherent information in the arrival at every step of the process to achieve near-optimal results. In particular the approach uses a consistent framework to define the optimal time-frequency windows on which to make estimates, to make the bearing estimates themselves, to construct metrics helpful in choosing the better estimates or admitting that the bearing is immeasurable, and finally to apply bias corrections when calibration information is available to yield a single final estimate. The algorithm was applied to a small but challenging set of events in a seismically active region. It demonstrated remarkable utility by providing better estimates and insights than previously available. Various monitoring implications are noted from these findings.

  20. Active Magnetic Bearings – Magnetic Forces

    DEFF Research Database (Denmark)

    Kjølhede, Klaus

    2006-01-01

    of the magnetic forces are led by using different experimental tests: (I) by using hall sensors mounted directly on the poles (precise measurements of the magnetic flux) and by an auxiliary system, composed of strain gages and flexible beams attached to the rotor; (II) by measuring the input current and bearing......Parameter identification procedures and model validation are major steps towards intelligent machines supported by active magnetic bearings (AMB). The ability of measuring the electromagnetic bearing forces, or deriving them from measuring the magnetic flux, strongly contributes to the model...... of the work is the characterization of magnetic forces by using two experimental different experimental approaches. Such approaches are investigated and described in details. A special test rig is designed where the 4 poles - AMB is able to generate forces up to 1900 N. The high precision characterization...

  1. Are organohalogen contaminants a bears (Ursus maritimus)?

    DEFF Research Database (Denmark)

    Sonne, Christian; Dietz, Rune; Leifsson, PS;

    2006-01-01

    Tissues of polar bears (Ursus maritimus) from East Greenland contain the highest concentrations of organohalogen contaminants (OHCs) among subpopulations of any mammalian species in the Arctic. Negative associations also have been found between OHC concentrations and bone mineral density and liver...... histology parameters for this subpopulation of polar bears. The present study examined the OHC concentrations and adverse effects on renal tissue for 75 polar bears collected during 1999 to 2002. Specific lesions were diffuse glomerular capillary wall thickening, mesangial glomerular deposits, tubular......PBDE, polychlorinated biphenyl, and hexachlorocyclohexane concentrations. The lesions were consistent with those reported previously in highly OHC-contaminated Baltic seal populations and exposed laboratory animals. The renal lesions were a result of aging. However, based on the above statistical findings as well...

  2. Big Bear Exploration Ltd. 1998 annual report

    International Nuclear Information System (INIS)

    During the first quarter of 1998 Big Bear completed a purchase of additional assets in the Rainbow Lake area of Alberta in which light oil purchase was financed with new equity and bank debt. The business plan was to immediately exploit these light oil assets, the result of which would be increased reserves, production and cash flow. Although drilling results in the first quarter on the Rainbow Lake properties was mixed, oil prices started to free fall and drilling costs were much higher than expected. As a result, the company completed a reduced program which resulted in less incremental loss and cash flow than it budgeted for. On April 29, 1998, Big Bear entered into agreement with Belco Oil and Gas Corp. and Moan Investments Ltd. for the issuance of convertible preferred shares at a gross value of $15,750,000, which shares were eventually converted at 70 cents per share to common equity. As a result of the continued plunge in oil prices, the lending value of the company's assets continued to fall, requiring it to take action in order to meet its financial commitments. Late in the third quarter Big Bear issued equity for proceeds of $11,032,000 which further reduced the company's debt. Although the company has been extremely active in identifying and pursuing acquisition opportunities, it became evident that Belco Oil and Gas Corp. and Big Bear did nor share common criteria for acquisitions, which resulted in the restructuring of their relationship in the fourth quarter. With the future of oil prices in question, Big Bear decided that it would change its focus to that of natural gas and would refocus ts efforts to acquire natural gas assets to fuel its growth. The purchase of Blue Range put Big Bear in a difficult position in terms of the latter's growth. In summary, what started as a difficult year ended in disappointment

  3. CFD Investigation of Influences of Reverse Textures on Bearing Surface of a Journal Bearing

    Directory of Open Access Journals (Sweden)

    Santosh Mishra

    2014-01-01

    Full Text Available It has always been the subject of interest and research to find out most efficient method to minimize the frictional loss of any mating surface in any mechanism. But it has been identified that only improvement of lubricating material cannot help much. For this reason research on design modification was started and still going on to optimize the design of mating surfaces so that losses be minimum. In this paper a research has been done on the design of bearing surface of a journal bearing. Journal bearing is a very important part of many machines specially turbines used in Power generation and rolling mills used in steel making sectors. By modifying the design of the bearing surface, load carrying capacity of a journal bearing can be increased and thus its performance can be improved. It is proved by many researches that, by putting cylindrical dimples on bearing surface the performance of a journal bearing can be increased. To measure the performance of a journal bearing three parameters are usually used. Those are, (i Load Carrying Capacity, (ii Frictional resisting force and (iii Ratio of Frictional resistance and Load carrying capacity, which is called Frictional coefficient. In this work a modification has been done on the work of Cupillard. Cupillard considered only the cylindrical dimples for the sake of manufacturing simplicity, but in this work a different configuration of dimple has been considered and its influence on bearing performance has been studied. It is proved by many researches that, by putting cylindrical dimples on bearing surface the performance of a journal bearing can be increased. To measure the performance of a journal bearing three parameters are usually used. Those are, (i Load Carrying Capacity, (ii Frictional resisting force and (iii Ratio of Frictional resistance and Load carrying capacity, which is called Frictional coefficient. In this work a modification has been done on the work of Cupillard at all (reference

  4. Cationic ruthenium alkylidene catalysts bearing phosphine ligands

    OpenAIRE

    Endo, Koji; Grubbs, Robert H.

    2016-01-01

    The discovery of highly active catalysts and the success of ionic liquid immobilized systems have accelerated attention to a new class of cationic metathesis catalysts. We herein report the facile syntheses of cationic ruthenium catalysts bear-ing bulky phosphine ligands. Simple ligand exchange using silver(I) salts of non-coordinating or weakly coordinating anions pro-vided either PPh3 or chelating Ph2P(CH2)nPPh2 (n = 2 or 3) ligated cationic catalysts. The structures of these newly reported...

  5. Coated Conductors for the Magnetic Bearing Application

    Science.gov (United States)

    Sass, Felipe; Dias, Daniel Henrique Nogueira; Sotelo, Guilherme Gonçalves; Júnior, Rubens de Andrade

    The second generation (2G) of superconductor wires have been considered for several applications lately. This work presents a preliminary study of superconducting magnetic bearings (SMB) using 2G wires as passive levitators. A superconducting block using stacked 2G wires was built to evaluate the magnetic bearing behavior, thought levitation force measurements, when a permanent magnet cylinder approaches or moves away from the block. The superconducting block was compared with an YBCO bulk with nearly the same dimensions and the results show a promising potential for this application.

  6. Rotor/bearing system dynamic stiffness measurements

    Science.gov (United States)

    Muszynska, A.

    1985-01-01

    Sweep perturbation testing as used in Modal Analysis when applied to a rotating machine has to take into consideration the machine dynamic state of equilibrium at its operational rotative speed. This stands in contrasts to a static equilibrium of nonrotating structures. The rotational energy has a significant influence on rotor dynamic characteristics. The best perturbing input for rotating machines is a forward or reverse rotating, circular force applied directly to the shaft. Determination of Dynamic Stiffness Characteristics of the rotor bearing system by nonsynchronous perturbation of a symmetric rotating shaft supported in one relatively rigid and one oil lubricated bearing.

  7. Grizzly bear habitat selection is scale dependent.

    Science.gov (United States)

    Ciarniello, Lana M; Boyce, Mark S; Seip, Dale R; Heard, Douglas C

    2007-07-01

    The purpose of our study is to show how ecologists' interpretation of habitat selection by grizzly bears (Ursus arctos) is altered by the scale of observation and also how management questions would be best addressed using predetermined scales of analysis. Using resource selection functions (RSF) we examined how variation in the spatial extent of availability affected our interpretation of habitat selection by grizzly bears inhabiting mountain and plateau landscapes. We estimated separate models for females and males using three spatial extents: within the study area, within the home range, and within predetermined movement buffers. We employed two methods for evaluating the effects of scale on our RSF designs. First, we chose a priori six candidate models, estimated at each scale, and ranked them using Akaike Information Criteria. Using this method, results changed among scales for males but not for females. For female bears, models that included the full suite of covariates predicted habitat use best at each scale. For male bears that resided in the mountains, models based on forest successional stages ranked highest at the study-wide and home range extents, whereas models containing covariates based on terrain features ranked highest at the buffer extent. For male bears on the plateau, each scale estimated a different highest-ranked model. Second, we examined differences among model coefficients across the three scales for one candidate model. We found that both the magnitude and direction of coefficients were dependent upon the scale examined; results varied between landscapes, scales, and sexes. Greenness, reflecting lush green vegetation, was a strong predictor of the presence of female bears in both landscapes and males that resided in the mountains. Male bears on the plateau were the only animals to select areas that exposed them to a high risk of mortality by humans. Our results show that grizzly bear habitat selection is scale dependent. Further, the

  8. Grouted Pile and Its Bearing Capacity

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The grouting method applied in bored pile is an improvement to the conventional bored pile. Load tests have proved that grouting under the bored pile tip is an effective method to enhance the bearing capacity of the pile and to reduce the pile settlement. In this paper, the grouting technology is described and pile-load test results are discussed. In order to put the grouting method into design practice, the authors analyze the working mechanism of soil compaction. And, based on the theory of cavities expansion in soil mass, approximate formulae are proposed for estimating the bearing capacity of the grouted pile. The theoretical prediction agrees well with the load test results.

  9. Wear Analysis of Wind Turbine Gearbox Bearings

    Energy Technology Data Exchange (ETDEWEB)

    Blau, Peter Julian [ORNL; Walker, Larry R [ORNL; Xu, Hanbing [ORNL; Parten, Randy J [ORNL; Qu, Jun [ORNL; Geer, Tom [ORNL

    2010-04-01

    The objective of this effort was to investigate and characterize the nature of surface damage and wear to wind turbine gearbox bearings returned from service in the field. Bearings were supplied for examination by S. Butterfield and J. Johnson of the National Wind Technology Center (NREL), Boulder, Colorado. Studies consisted of visual examination, optical and electron microscopy, dimensional measurements of wear-induced macro-scale and micro-scale features, measurements of macro- and micro-scale hardness, 3D imaging of surface damage, studies of elemental distributions on fracture surfaces, and examinations of polished cross-sections of surfaces under various etched and non-etched conditions.

  10. Local Attitudes towards Bear Management after Illegal Feeding and Problem Bear Activity

    Directory of Open Access Journals (Sweden)

    David Fraser

    2013-09-01

    Full Text Available The “pot bears” received international media attention in 2010 after police discovered the intentional feeding of over 20 black bears during the investigation of an alleged marijuana-growing operation in Christina Lake, British Columbia, Canada. A two-phase random digit dialing survey of the community was conducted in 2011 to understand local perspectives on bear policy and management, before and after a summer of problem bear activity and government interventions. Of the 159 households surveyed in February 2011, most had neutral or positive attitudes towards bears in general, and supported the initial decision to feed the food-conditioned bears until the autumn hibernation. In contrast to wildlife experts however, most participants supported relocating the problem bears, or allowing them to remain in the area, ahead of killing; in part this arose from notions of fairness despite the acknowledged problems of relocation. Most locals were aware of the years of feeding but did not report it, evidently failing to see it as a serious form of harm, even after many bears had been killed. This underscores the importance of preventive action on wildlife feeding and the need to narrow the gap between public and expert opinion on the likely effects of relocation versus killing.

  11. Studies on Excess Volume, Viscosity, and Speed of Sound of Binary Mixtures of Methyl Benzoate in Ethers at T=(303.15,308.15, and 313.15) K

    OpenAIRE

    Rathnam, M. V.; Ambavadekar, Devappa R.; Nandini, M.

    2013-01-01

    Densities, viscosities, and speed of sound have been determined at T = (303.15, 308.15, and 313.15) K for the binary mixtures of methyl benzoate with tetrahydrofuran, 1,4-dioxane, anisole, and butyl vinyl ether over the entire range of composition. Using these measured values, excess volume VE, deviation in viscosities Δη, excess Gibb’s free energy of activation for viscous flow ΔG*E, and deviation in isentropic compressibility Δks have been calculated. These calculated binary data have been...

  12. Lubricant replacement in rolling element bearings for weapon surety devices

    Energy Technology Data Exchange (ETDEWEB)

    Steinhoff, R.; Dugger, M.T.; Varga, K.S. [Sandia National Laboratories, Albuquerque, NM (United States)

    1996-05-01

    Stronglink switches are a weapon surety device that is critical to the nuclear safety theme in modem nuclear weapons. These stronglink switches use rolling element bearings which contain a lubricant consisting of low molecular weight polytetrafluoroethylene (PTFE) fragments. Ozone-depleting solvents are used in both the manufacture and application of this lubricant. An alternate bearing lubrication for stronglink switches is needed that will provide long-term chemical stability, low migration and consistent performance. Candidates that were evaluated include bearings with sputtered MoS{sub 2} on the races and retainers, bearings with TiC-coated balls, and bearings with Si{sub 3}N{sub 4} balls and steel races. These candidates were compared to the lubricants currently used which are bearings lubricated with PTFE fragments of low molecular weight in a fluorocarbon solvent. The candidates were also compared to bearings lubricated with a diester oil which is representative of bearing lubricants used in industrial applications. Evaluation consisted of cycling preloaded bearings and subjecting them to 23 gRMS random vibration. All of the candidates are viable substitutes for low load application where bearing preload is approximately 1 pound. For high load applications where the bearing preload is approximately 10 pounds, bearings with sputtered MoS{sub 2} on the races and retainers appear to be the best substitutes. Bearings with TiC-coated balls also appear to be a viable candidate but these bearings did not perform as well as the sputtered MoS{sub 2}.

  13. NANO-BEARING: THE DESIGN OF A NEW TYPE OF AIR BEARING WITH FLEXURE STRUCTURE

    Institute of Scientific and Technical Information of China (English)

    KO Pui Hang; DU Ruxu

    2007-01-01

    A new type of air bearing with flexure structure is introduced. The new bearing is designed for precision mechanical engineering devices such as mechanical watch movement. The new design uses the flexure structure to provide 3D damping to absorb shocks from all directions. Two designs are presented: one has 12 T-shape slots in the radian direction while the other has 8 spiral slots in the radian direction. Both designs have flexure mountings on the axial directions. Based on the finite element analysis (FEA), the new bearing can reduce the vibration (displacement) by as much as 8.37% and hence, can better protect the shafts.

  14. Extended Life Testing of Duplex Ball Bearings

    Science.gov (United States)

    Mobley, Jeffrey; Robertson, Michael; Hodges, Charles

    2016-01-01

    Sierra Nevada Corporation’s Space Systems performed bearing life testing for the Scan Mirror Motor/Encoder Assembly (SMMA), part of the Scan Mirror Assembly on-board the Aerosol Polarimetry Sensor (APS) on the NASA Glory Spacecraft. The baseline bearing life test duration extended beyond the launch date for the Glory Spacecraft; a risk that the program was willing to undertake with the understanding that if any anomalies or failures occurred before the required life was achieved, then the mission objectives or operating profile could be modified on orbit to take those results into account. Even though the Glory Spacecraft failed to reach orbit during its launch in March of 2011, the bearing life testing was continued through a mutual understanding of value between Sierra Nevada Corporation and our customer; with a revised goal of testing to failure rather than completing a required number of life cycles. Life testing thus far has not only exceeded the original mission required life, but has also exceeded the published test data for Cumulative Degradation Factor (CDF) from NASA/CR-2009-215681. Many lessons were learned along the way regarding long life testing. The bearing life test has been temporarily suspended due to test support equipment issues.

  15. Angular-momentum-bearing modes in fission

    International Nuclear Information System (INIS)

    The angular-momentum-bearing degrees of freedom involved in the fission process are identified and their influence on experimental observables is discussed. The excitation of these modes is treated in the ''thermal'' limit, and the resulting distributions of observables are calculated. Experiments demonstrating the role of these modes are presented and discussed. 61 refs., 12 figs

  16. Bearings fault detection using inference tools

    OpenAIRE

    Prieto, Miguel Delgado; Roura, Jordi Cusidó i; Martínez, Jose Luis Romeral

    2011-01-01

    The most used electric machine in the industry is the Induction Motor (IM), due to its simplicity and reduced cost. The analysis of the origin of IMs failures exhibits that the bearings are the major source of fault, and even a common cause of degradation in other kinds of motors as Permanent Magnet Synchronous Machines.

  17. Experimental investigations of active air bearings

    DEFF Research Database (Denmark)

    Santos, Ilmar; Morosi, Stefano

    2012-01-01

    Along with traditional oil lubrication, increasing demand for high-speed applications has renewed attention to gas bearings technology. Traditional aerostatic and aerodynamic gas lubrication has been widely used in a variety of applications, ranging from high-speed spindles to micro and meso-scal...

  18. Thermo-hydrodynamic lubrication in hydrodynamic bearings

    CERN Document Server

    Bonneau, Dominique; Souchet, Dominique

    2014-01-01

    This Series provides the necessary elements to the development and validation of numerical prediction models for hydrodynamic bearings. This book describes the thermo-hydrodynamic and the thermo-elasto-hydrodynamic lubrication. The algorithms are methodically detailed and each section is thoroughly illustrated.

  19. Rotor Vibration Reduction via Active Hybrid Bearings

    DEFF Research Database (Denmark)

    Nicoletti, Rodrigo; Santos, Ilmar

    2002-01-01

    The use of fluid power to reduce and control rotor vibration in rotating machines is investigated. An active hybrid bearing is studied, whose main objective is to reduce wear and vibration between rotating and stationary machinery parts. By injecting pressurised oil into the oil film, through...... with experiment, and simulations show the feasibility of controlling shaft vibration through this active device....

  20. The economics of roadside bear viewing

    Science.gov (United States)

    Richardson, Leslie; Rosen, Tatjana; Gunther, Kerry; Schwartz, Chuck

    2014-01-01

    Viewing bears along roadside habitats is a popular recreational activity in certain national parks throughout the United States. However, safely managing visitors during traffic jams that result from this activity often requires the use of limited park resources. Using unique visitor survey data, this study quantifies economic values associated with roadside bear viewing in Yellowstone National Park, monetary values that could be used to determine whether this continued use of park resources is warranted on economic grounds. Based on visitor expenditure data and results of a contingent visitation question, it is estimated that summer Park visitation would decrease if bears were no longer allowed to stay along roadside habitats, resulting in a loss of 155 jobs in the local economy. Results from a nonmarket valuation survey question indicate that on average, visitors to Yellowstone National Park are willing to pay around $41 more in Park entrance fees to ensure that bears are allowed to remain along roads within the Park. Generalizing this value to the relevant population of visitors indicates that the economic benefits of allowing this wildlife viewing opportunity to continue could outweigh the costs of using additional resources to effectively manage these traffic jams.

  1. Surface layer characterisation of bearing rings

    Directory of Open Access Journals (Sweden)

    S.J. Skrzypek

    2007-11-01

    Full Text Available austenite. Theoretical calculation of residual macro-stresses due to volume fraction of transformed austenite in bearing rings and following measurements of residual stresses were carried out as well. The bearing elements were made of 100Cr6 steel and they were smoothed and grinded.Design/methodology/approach: Particular features of diffraction patterns like angle position; shape and intensity are used to characterize phase composition, residual micro and macro-stresses, crystallographic texture, lattice parameter, defects density and crystalline size.Findings: Machining by micro-deformation causes microstructural changes i.e. mechanically induced phase transformation of retained austenite and residual macrostresses. E.g. grinding cased tension and small compression whereas the mechanical smoothing of bearing rings caused high compresive residual stresses about -713 MPa.Research limitations/implications: For precise interpretation of differences between following results needs another investigations: i.e. measurement of retained austenite and residual stresses in rings after heat treatment before any mechanical treatment.Practical implications: The non-destructive character and large number of structural informations contained in diffraction pattern are the beneficial feature of diffraction methods. Therefore they have potential ability in application to technological operations and to diagnostic during fatigue.Originality/value: The non-destructive structure characterisation of surface layers for various kinds of bearing rings can be powerful method in surface characterization and in quality control. This results contribute in general relations between microstructure and properties.

  2. MAGNETIC FLUID BEARINGS OF MINING EQUIPMENT

    Directory of Open Access Journals (Sweden)

    I. Gorlov

    2012-01-01

    Full Text Available The paper considers a problem pertaining to selection friction pair materials for plain bearings of mining equipment which are lubricated with  nano-dispersed magnetic oil. Methodology for equipment tests, technology for obtaining new anti-friction materials (polymer, ceramic, amorphous and investigation results are presented in the paper.

  3. Load-Bearing Capacity of Roof Trusses

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Damkilde, Lars; Munch-Andersen, J.

    2004-01-01

    systems such as roof trusses are established and statistical characteristics of the load bearing capacity are determined. The results show that there is a significant increase in the characteristic (nominal) value and a reduction in the coefficient of variation (COV) for typical loads such as permanent...

  4. Magnetic Bearing Controller Improvements for High Speed Flywheel System

    Science.gov (United States)

    Dever, Timothy P.; Brown, Gerald V.; Jansen, Ralph H.; Kascak, Peter E.; Provenza, Andrew J.

    2003-01-01

    A magnetic bearing control system for a high-speed flywheel system is described. The flywheel utilizes a five axis active magnetic bearing system, using eddy current sensors for position feedback to the bearing controller. Magnetic bearing controller features designed to improve flywheel operation and testing are described. Operational improvements include feed forward control to compensate for rotor imbalance, moving notch filtering to compensate for synchronous and harmonic rotational noise, and fixed notching to prevent rotor bending mode excitation. Testing improvements include adding safe gain, bearing current hold, bearing current zero, and excitation input features. Performance and testing improvements provided by these features are measured and discussed.

  5. Blade Bearing Friction Estimation of Operating Wind Turbines

    DEFF Research Database (Denmark)

    Perisic, Nevena; Pedersen, Bo Juul; Kirkegaard, Poul Henning

    2012-01-01

    Blade root bearing on a wind turbine (WTG) enables pitching of blades for power control and rotor braking and is a WTG critical component. As the size of modern WTGs is constantly increasing, this leads to relatively less rigid bearings, more sensitive to deformations, thus WTG operational...... reliability can be increased by continuous monitoring of blade bearing. High blade bearing friction is undesirable, as it may be associated with excessive heating of the surfaces, damage and/or inefficient operation. Thus, continuous observation of bearing friction level is crucial for blade bearing health...

  6. Teager Energy Spectrum for Fault Diagnosis of Rolling Element Bearings

    Science.gov (United States)

    Feng, Zhipeng; Wang, Tianjin; Zuo, Ming J.; Chu, Fulei; Yan, Shaoze

    2011-07-01

    Localized damage of rolling element bearings generates periodic impulses during running. The repeating frequency of impulses is a key indicator for diagnosing the localized damage of bearings. A new method, called Teager energy spectrum, is proposed to diagnose the faults of rolling element bearings. It exploits the unique advantages of Teager energy operator in detecting transient components in signals to extract periodic impulses of bearing faults, and uses the Fourier spectrum of Teager energy to identify the characteristic frequency of bearing faults. The effectiveness of the proposed method is validated by analyzing the experimental bearing vibration signals.

  7. Modeling of Hybrid Permanent Magnetic-Gas Bearings

    DEFF Research Database (Denmark)

    Morosi, Stefano; Santos, Ilmar

    2009-01-01

    of the gas bearing is balanced by the properties of the passive magnetic one. At high speeds the dynamic characteristics of the gas bearing are improved by offsetting the stator ring of the permanent magnetic bearing. Furthermore this design shows a kind of redundancy, which offers soft failure properties....... In the present paper, a detailed mathematical modeling of the gas bearing based on the compressible form of the Reynolds equation is presented. Perturbation theory is applied in order to identify the dynamic characteristic of the bearing. Due to the simple design of the magnetic bearings elements - being...

  8. Computing Operating Characteristics Of Bearing/Shaft Systems

    Science.gov (United States)

    Moore, James D.

    1996-01-01

    SHABERTH computer program predicts operating characteristics of bearings in multibearing load-support system. Lubricated and nonlubricated bearings modeled. Calculates loads, torques, temperatures, and fatigue lives of ball and/or roller bearings on single shaft. Provides for analysis of reaction of system to termination of supply of lubricant to bearings and other lubricated mechanical elements. Valuable in design and analysis of shaft/bearing systems. Two versions of SHABERTH available. Cray version (LEW-14860), "Computing Thermal Performances Of Shafts and Bearings". IBM PC version (MFS-28818), written for IBM PC-series and compatible computers running MS-DOS.

  9. Kenai Peninsula Brown Bear Studies : Report of the Interagency Brown Bear Study Team, 1986

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This report summarizes work conducted during the 1986 field season on brown bear (Ursus arctos) from the Kenai Peninsula, Alaska. Ground surveys were conducted to...

  10. Rotor Bearing System Analysis Using the Transfer Matrix Method with Thickness Assumption of Disk and Bearing

    CERN Document Server

    Ghasemalizadeh, Omid; Sadeghi, Hossein; Ahmadian, Mohammad Taghi

    2013-01-01

    One of the methods to find the natural frequencies of rotating systems is the application of the transfer matrix method. In this method the rotor is modeled as several elements along the shaft which have their own mass and moment of inertia. Using these elements, the entire continuous system is discretized and the corresponding differential equation can be stated in matrix form. The bearings at the end of the shaft are modeled as equivalent spring and dampers which are applied as boundary conditions to the discretized system. In this paper the dynamics of a rotor-bearing system is analyzed, considering the gyroscopic effect. The thickness of the disk and bearings is also taken into account. Continuous model is used for shaft. Results Show that, the stiffness of the shaft and the natural frequencies of the system increase, while the amplitude of vibration decreases as a consequence of increasing the thickness of the bearing.

  11. Yellowstone grizzly bear investigations: Annual report of the Interagency Grizzly Bear Study Team, 2006

    Science.gov (United States)

    Schwartz, Charles C.; Haroldson, Mark A.; West, Karrie K.

    2007-01-01

    The contents of this Annual Report summarize results of monitoring and research from the 2006 field season. The report also contains a summary of nuisance grizzly bear (Ursus arctos horribilis) management actions.

  12. Yellowstone grizzly bear investigations: Annual report of the Interagency Grizzly Bear Study Team, 2001

    Science.gov (United States)

    Schwartz, Charles C.; Haroldson, Mark A.

    2001-01-01

    The contents of this Annual Report summarize results of monitoring and research from the 2001 field season. The report also contains a summary of nuisance grizzly bear (Ursus arctos horribilis) management actions.

  13. Fixed or mobile-bearing total knee arthroplasty

    Directory of Open Access Journals (Sweden)

    Liau Jiann-Jong

    2007-01-01

    Full Text Available Abstract Fixed and mobile-bearing in total knee arthroplasty are still discussed controversially. In this article, biomechanical and clinical aspects in both fixed and mobile-bearing designs were reviewed. In biomechanical aspect, the mobile-bearing design has proved to provide less tibiofemoral contact stresses under tibiofemoral malalignment conditions. It also provides less wear rate in in-vitro simulator test. Patients with posterior stabilized mobile-bearing knees had more axial tibiofemoral rotation than patients with posterior stabilized fixed-bearing knees during gait as well as in a deep knee-bend activity. However, in clinical aspect, the mid-term or long-term survivorship of mobile-bearing knees has no superiority over that of fixed-bearing knees. The theoretical advantages for mobile-bearing design to provide a long-term durability have not been demonstrated by any outcome studies. Finally, the fixed-bearing design with all-polyethylene tibial component is suggested for relatively inactive, elder people. The mobile-bearing design is suggested for younger or higher-demand patients due to the potential for reduced polyethylene wear and more normal kinematics response after joint replacement. For younger surgeon, the fixed-bearing design is suggested due to less demand for surgical technique. For experienced surgeon, one familiar surgical protocol and instrumentation is suggested rather than implant design, either fixed-bearing or mobile-bearing.

  14. The thermodynamic properties of a new type catcher bearing used in active magnetic bearings system

    International Nuclear Information System (INIS)

    Normally a rotor levitated by active magnetic bearings (AMBs) system would rotate without contacting with any stator component, but the possibility still remains that the supporting force might lose temporarily or permanently, thus requiring the Catcher bearings (CBs) to provide backup protection in case of the failure of AMBs. A new type CB with two separate rolling element bearing series could have the speed distribution between the inner race and intermediate race according to certain ratio, in which the speed of each roller element bearing decreases with the limit speed of the whole CB increasing, offering high capability to sustain its initial rotation speed. Based on the theory of heat transfer, tribology, and rotor dynamics, this paper analyzes the thermal structure of double-decker catcher bearing (DDCB) and single-decker catcher bearing (SDCB), respectively. Through this structure, the thermal resistances and equations of heat transfer can be obtained. Then we calculate the friction heat and temperature distribution in the various CBs upon rotor's dropping on SDCB or DDCB, followed by the discussion on the CBs temperature rise's effects on lubrication conditions and rotor dynamics parameters. Finally various experiments are carried out to measure the temperature rise of different CBs. The results obtained validate the theoretical analysis and also provide main methods to reduce heat generation. Using DDCB is proved to be effective to reduce the temperature rise. - Highlights: • The DDCB is a more suitable catcher bearing for AMBs. • Compared to SDCB, using DDCB, the temperature rise can decrease in the same states. • A lower viscosity of lubricant may induce a lower temperature rise. • The inner raceway temperature of the first layer bearing is the highest. • Reducing the unbalance mass of the rotor is a method to decrease the temperature rise

  15. Biomechanical analysis of fixed bearing and mobile bearing total knee prostheses

    OpenAIRE

    Urwin, Samuel

    2014-01-01

    In total knee replacement (TKR) surgery, mobile bearing (MB) total knee prostheses were designed to more closely mimic the function of the normal knee than traditional fixed bearing (FB) designs by allowing axial mobility between the polyethylene insert and tibial tray. Despite the hypothetical benefits of the MB design, few studies have objectively analysed knee biomechanics during activities of daily living (ADLs) in the laboratory compared to FB designs. This thesis aimed to substantiate t...

  16. THE STRUCTURAL ANALYSIS OF STEEL SILOS WITH CYLINDRICAL-WALL BEARING AND PROFILE-STEEL BEARING

    OpenAIRE

    Zhengjun Tang; Daibiao Zhou; Chenwei Peng; Wenping Wu

    2015-01-01

    The silos are widely used in bulk material in many fields such as agriculture, mining, chemical, electric power storage, etc. Thin metal cylindrical silo shells are vulnerable to buckling failure caused by the compressive wall friction force. In this paper, the structural analysis of two types of steel silo with cylindrical-wall bearing and profile-steel bearing is implemented by Abaqus finite element analysis. The results indicate that under the same loading conditions, steel silos with prof...

  17. Preclinical pharmacokinetics, tissue distribution and plasma protein binding of sodium (±-5-bromo-2-(α-hydroxypentyl benzoate (BZP, an innovative potent anti-ischemic stroke agent

    Directory of Open Access Journals (Sweden)

    Xin Tian

    2016-08-01

    Full Text Available Sodium (±-5-bromo-2-(α-hydroxypentyl benzoate (BZP is a potential cardiovascular drug and exerts potent neuroprotective effect against transient and long-term ischemic stroke in rats. BZP could convert into 3-butyl-6-bromo-1(3H-isobenzofuranone (Br-NBP in vitro and in vivo. However, the pharmacokinetic profiles of BZP and Br-NBP still have not been evaluated. For the purpose of investigating the pharmacokinetic profiles, tissue distribution and plasma protein binding of BZP and Br-NBP, a rapid, sensitive and specific method based on liquid chromatography coupled to mass spectrometry (LC-MS/MS has been developed for determination of BZP and Br-NBP in biological samples. The results indicated that BZP and Br-NBP showed a short elimination half-life, and pharmacokinetic profile in rats (3, 6 and 12 mg/kg; i.v. and beagle dogs (1, 2 and 4 mg/kg; i.v.gtt were obtained after single dosing of BZP. After multiple dosing of BZP, there was no significant accumulation of BZP and Br-NBP in the plasma of rats and beagle dogs. Following i.v. single dose (6 mg/kg to rats, BZP and Br-NBP were distributed rapidly into all tissues examined, with the highest concentrations of BZP and Br-NBP in lung and kidney, respectively. The brain distribution of Br-NBP in middle cerebral artery occlusion (MCAO rats was more than in normal rats (P<0.05. The plasma protein binding degree of BZP at three concentrations (8000, 20000 and 80000 ng/mL from rat, beagle dog and human plasma were 98.1~98.7%, 88.9~92.7% and 74.8%~83.7% respectively. In conclusion, both BZP and Br-NBP showed short half-life, good dose-linear pharmacokinetic profile, wide tissue distribution and different degree protein binding to various species plasma. This was the first preclinical pharmacokinetic investigation of BZP and Br-NBP in both rats and beagle dogs, which provided vital guidance for further preclinical research and the subsequent clinical trials.

  18. Experimental Study and Dynamic Modeling of Metal Rubber Isolating Bearing

    Science.gov (United States)

    Zhang, Ke; Zhou, Yanguo; Jiang, Jian

    2015-12-01

    In this paper, dynamic shear mechanical properties of a new metal rubber isolating bearing is tested and studied. The mixed damping model is provided for theoretical modeling of MR isolating bearing, the shear stiffness and damping characteristics of the MR bearing can be analyzed separately and easily discussed, and the mixed damping model is proved to be an rather effective approach. The test results indicate that loading frequency bears little impact over shear property of metal rubber isolating bearing, the total energy consumption of metal rubber isolating bearing increases with the increase in loading amplitude. With the increase in loading amplitude, the stiffness of the isolating bearing will reduce showing its “soft property” and the type of damping force gradually changes to be close to dry friction. The features of “soft property” and dry friction energy consumption of metal rubber isolating bearing are very useful in practical engineering application.

  19. Polar bear den survey, Arctic National Wildlife Range

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — In conjunction with the Polar Bear Research Project being supervised by Mr. Jack Lentfer of the Bureau of Sport Fisheries and Wildlife two Polar Bear den surveys...

  20. Investigation of tribological and mechanical properties of metal bearings

    Indian Academy of Sciences (India)

    Bekir Sadik Ünlü

    2009-08-01

    Copper, aluminum and tin–lead based alloys are widely used as journal bearing materials in tribological applications. Bronze and brass are widely used as journal bearing materials for copper based alloys. Zamacs find applications as journal bearing materials for zinc based alloys, while duralumines are chosen as journal bearing materials for aluminum based alloys. In addition, white metals are widely used as journal bearing materials for tin–lead based alloys. These alloys ensure properties expected from journal bearings. In this study, tribological and mechanical properties of these journal bearings manufactured by metals were investigated. SAE 1050 steel shaft was used as counter abrader. Experiments were carried out in every 30 min for a total of 150 min by using radial journal bearing wear test rig.

  1. Bear range-grazing area survey: Joint report

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Recommendations for establishing livestock grazing area, consistent with refuge purposes and minimization of bear attacks. Includes statistics on bear kills,...

  2. Population Parameters and Harvest Characteristics of Black Bears in Georgia

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — This report summarizes findings of black bear distribution and population trends throughout Georgia and evaluates black bear harvest trends from 1992 to 2002....

  3. A plan for the management of the Kodiak brown bear

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Management districts will be used as a tool to manage the population of bear on Kodiak Island. Theoretically, 204 bear may be taken off the refuge annually without...

  4. Interchangeable Bearings for Profile and Weight Trade Studies Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Air-Lock, Incorporated is proposing to design fully sealed shoulder and arm bearings with interchangeable bearing housings. The interchangeable housings shall be...

  5. Shaft centre orbit for dynamically loaded radial bearings

    DEFF Research Database (Denmark)

    Klit, Peder; Vølund, Anders

    2002-01-01

    The aim of this work is to demonstrate how to utilize the bearings damping coefficients to estimate the orbit for a dynamically loaded journal bearing. The classical method for this analysis was developed by Booker in 1965 Booker1 and described further in 1972 Booker2. Several authors have refined...... this method over the years. In 1966 Jorgen W. Lund published an approach to find the dynamic coefficients of a journal bearing by a first order perturbation of the Reynold´s equation. These coefficients made it possible to perform a rotor-bearing stability analysis for a statically loaded bearing. In the mid...... seventies Jorgen W. Lund pointed out in lecture notes that the dynamic damping coefficients of the bearing could be used to find the shaft orbit for dynamically loaded bearings. For simplicity the "Short-Width-Journal-Bearing Theory" is used as a basis for finding the damping coefficients in this work...

  6. Self-Bearing Motor-Generator for Flywheels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Self-bearing or ?bearingless? motors perform both motor and bearing support functions but such devices have not yet achieved speeds above 15,000 rpm. The innovation...

  7. Kodiak brown bear population on Kodiak Island, Alaska

    Data.gov (United States)

    US Fish and Wildlife Service, Department of the Interior — Methods and estimates of the Brown bear population on Kodiak Island. The total number of Kodiak Brown Bears on Kodiak Island has been estimated to be 1669. Three...

  8. The possibility of evaluating turbo-set bearing misalignment defects on the basis of bearing trajectory features

    Science.gov (United States)

    Rybczyński, Józef

    2011-02-01

    This paper presents the results of computer simulation of bearing misalignment defects in a power turbogenerator. This malfunction is typical for great multi-rotor and multi-bearing rotating machines and very common in power turbo-sets. Necessary calculations were carried out by the computer code system MESWIR, developed and used at the IFFM in Gdansk for calculating dynamics of rotors supported on oil bearings. The results are presented in the form of a set of journal and bush trajectories of all turbo-set bearings. Our analysis focuses on the vibrational effects of displacing the two most vulnerable machine bearings in horizontal and vertical directions by the maximum acceptable range calculated with regard to bearing vibration criterion. This assumption required preliminary assessment of the maximum values for the permissible bearing dislocations. We show the relations between the attributes of the particular bearing trajectories and the bearing displacements in relation to their base design position. The shape and dimensions of bearing trajectories are interpreted based on the theory of hydrodynamic lubrication of oil bearings. It was shown that the relative journal trajectories and absolute bush trajectories carry much important information about the dynamic state of the machine, indicating also the way in which bearings are loaded. Therefore, trajectories can be a source of information about the position and direction of bearing misalignments. This article indicates the potential of using trajectory patterns for diagnosing misalignment defects in rotating machines and suggests including sets of trajectory patterns to the knowledge base of a machine diagnostic system.

  9. Effects of sodium benzoate on liver and kidney in rats%苯甲酸钠多次给药对大鼠肝肾功能的影响

    Institute of Scientific and Technical Information of China (English)

    李锦玉; 李荣欣; 李京路; 毕红征

    2015-01-01

    目的:研究食品防腐剂苯甲酸钠多次给药对大鼠肝肾功能的影响。方法:选取50只健康SPF级SD大鼠,分为5组,每组10只,苯甲酸钠低、中、高剂量组分别灌胃给予苯甲酸钠(0.1、0.2、0.4 g/kg),阳性对照组给予山梨酸钾(0.2 g/kg),空白对照组给予生理盐水,1次/d,连续4周。检测末次给药后大鼠血清学指标(ALT、AST、ALP、GGT、TP、ALB、TBIL、BUN、Cre、UA),并观察肝肾组织病理学改变。结果:与空白对照组相比,苯甲酸钠低、中、高剂量组大鼠的各项血清生化学指标均有一定的异常,高剂量组最为显著(P均<0.05)。苯甲酸钠高剂量组大鼠肝脏出现了明显病理学异常,各组大鼠肾脏均未见病理学改变。结论:苯甲酸钠多次给药对大鼠肝肾,尤其是肝脏有一定的损害。%Aim:To study the effects of sodium benzoate on liver and kidney in rats .Methods: Fifty healthy SD rats were allocated into 5 groups and treated with sodium benzoate (0.1,0.2,0.4 g/kg),potassium sorbate(0.2 g/kg) and normal saline by gavage for 4 weeks.The serum indicators such as ALT , AST, ALP, GGT, TP, ALB, TBIL, BUN,Cre, and UA were determined and the liver and renal histology of the rats was observed .Results:Rats in each dose group of sodium ben-zoate had abnormal serum biochemical indicators , especially in high dose group .Furthermore, rats in sodium benzoate high dose group showed obvious pathological abnormalities in liver .Rats in all groups showed no pathological changes in kidneys . Conclusion:The frequent use of sodium benzoate could do harms to the kidney and liver especially to the liver in rats .

  10. Optimized Coolant-Flow Diverter For Increased Bearing Life

    Science.gov (United States)

    Subbaraman, Maria R.; Butner, Myles F.

    1995-01-01

    Coolant-flow diverter for rolling-element bearings in cryogenic turbopump designed to enhance cooling power of flow in contact with bearings and thereby reduce bearing wear. Delivers jets of coolant as close as possible to hot spots at points of contact between balls and race. Also imparts swirl that enhances beneficial pumping effect. Used with success in end ball bearing of high-pressure-oxidizer turbopump.

  11. Passive axial stabilization of a magnetic radial bearing by superconductors

    Energy Technology Data Exchange (ETDEWEB)

    Marinescu, M.; Marinescu, N. (Ing.-Buro f. Magnettechnik, Mailander Str.19, D-6000 Frankfurt/M. 70 (DE)); Tenbrink, J.; Krauth, H. (Vacuumschmelze GmbH, Gruner Weg 37, D-6450 Hanau (DE))

    1989-09-01

    Contactless bearings for high-speed operation can be constructed using passive magnet systems, which inherently need a second, active bearing for their stabilization. Completely passive bearings only can be obtained using diamagnetic materials. This study deals with the axial stabilization of magnetic radial bearings using a permanent magnet/superconductor system. Using finite element calculation procedures it is shown that axial forces of up 3000 N and stiffnesses of up to 400 N/mm may be achieved.

  12. Dynamic behaviour of ball bearing applications with constrained damping layers

    OpenAIRE

    Tillema, Hetzer G.

    2001-01-01

    Rolling bearing noise has become an aspect of increasing importance for the performance of rotating machinery, like electric motors and gearboxes. Generally, two aspects are important with regard to bearing noise, i.e. the transmission characteristics and the vibration generation characteristics. A potential source of vibrations are for example manufacturing imperfections of the different bearing components. Damping of bearing vibrations is enhanced by the lubrication film between the rolling...

  13. Rotor stability estimation with competing tilting pad bearing models

    Science.gov (United States)

    Cloud, C. Hunter; Maslen, Eric H.; Barrett, Lloyd E.

    2012-05-01

    When predicting the stability of rotors supported by tilting pad journal bearings, it is currently debated whether or not the bearings should be represented with frequency dependent dynamics. Using an experimental apparatus, measurements of pad temperatures, unbalance response and stability are compared with modeling predictions for two tilting pad bearing designs. Predictions based on frequency dependent tilting pad bearing dynamics exhibited significantly better correlation with the stability measurements than those assuming frequency independent dynamics.

  14. Gravimeter using high-temperature superconductor bearing.

    Energy Technology Data Exchange (ETDEWEB)

    Hull, J. R.

    1998-09-11

    We have developed a sensitive gravimeter concept that uses an extremely low-friction bearing based on a permanent magnet (PM) levitated over a high-temperature superconductor (HTS). A mass is attached to the PM by means of a cantilevered beam, and the combination of PM and HTS forms a bearing platform that has low resistance to rotational motion but high resistance to horizontal, vertical, or tilting motion. The combination acts as a low-loss torsional pendulum that can be operated in any orientation. Gravity acts on the cantilevered beam and attached mass, accelerating them. Variations in gravity can be detected by time-of-flight acceleration, or by a control coil or electrode that would keep the mass stationary. Calculations suggest that the HTS gravimeter would be as sensitive as present-day superconducting gravimeters that need cooling to liquid helium temperatures, but the HTS gravimeter needs cooling only to liquid nitrogen temperatures.

  15. Static Load Distribution in Ball Bearings

    Science.gov (United States)

    Ricci, Mario

    2010-01-01

    A numerical procedure for computing the internal loading distribution in statically loaded, single-row, angular-contact ball bearings when subjected to a known combined radial and thrust load is presented. The combined radial and thrust load must be applied in order to avoid tilting between inner and outer rings. The numerical procedure requires the iterative solution of Z + 2 simultaneous nonlinear equations - where Z is the number of the balls - to yield an exact solution for axial and radial deflections, and contact angles. Numerical results for a 218 angular-contact ball bearing have been compared with those from the literature and show significant differences in the magnitudes of the ball loads, contact angles, and the extent of the loading zone.

  16. Whitebark pine, grizzly bears, and red squirrels

    Science.gov (United States)

    Mattson, D.J.; Kendall, K.C.; Reinhart, D.P.; Tomback, D.F.; Arno, S.F.; Keane, R.E.

    2001-01-01

    Appropriately enough, much of this book is devoted to discussing management challenges and techniques. However, the impetus for action—the desire to save whitebark pine (Pinus albicaulis)—necessarily arises from the extent to which we cherish it for its beauty and its connections with other things that we value. Whitebark pine is at the hub of a fascinating web of relationships. It is the stuff of great stories (cf. Quammen 1994). One of the more interesting of these stories pertains to the dependence of certain grizzly bear (Ursus arctos horribilis) populations on its seeds, and the role that red squirrels (Tamiasciurus hudsonicus) play as an agent of transfer between tree and bear.

  17. 14 CFR 73.5 - Bearings; radials; miles.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Bearings; radials; miles. 73.5 Section 73.5 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION (CONTINUED) AIRSPACE SPECIAL USE AIRSPACE General § 73.5 Bearings; radials; miles. (a) All bearings and radials in this...

  18. PROVIDING SERVICEABILITY OF STRUCTURAL BEARING TYPES FOR ROADWAY BRIDGES

    Directory of Open Access Journals (Sweden)

    R. I. Polyuga

    2010-03-01

    Full Text Available In the article the description of structural bearing types for roadway bridges and their classification is given. Special attention is paid to effective bearings with elastomeric materials – rubber, pot, spherical ones. Characteristic defects of structural bearings and demands of serviceability are noticed.

  19. 14 CFR 71.7 - Bearings, radials, and mileages.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 2 2010-01-01 2010-01-01 false Bearings, radials, and mileages. 71.7 Section 71.7 Aeronautics and Space FEDERAL AVIATION ADMINISTRATION, DEPARTMENT OF TRANSPORTATION... REPORTING POINTS § 71.7 Bearings, radials, and mileages. All bearings and radials in this part are true...

  20. Mechanical design problems associated with turbopump fluid film bearings

    Science.gov (United States)

    Evces, Charles R.

    1990-01-01

    Most high speed cryogenic turbopumps for liquid propulsion rocket engines currently use ball or roller contact bearings for rotor support. The operating speeds, loads, clearances, and environments of these pumps combine to make bearing wear a limiting factor on turbopump life. An example is the high pressure oxygen turbopump (HPOTP) used in the Space Shuttle Main Engine (SSME). Although the HPOTP design life is 27,000 seconds at 30,000 rpms, or approximately 50 missions, bearings must currently be replaced after 2 missions. One solution to the bearing wear problem in the HPOTP, as well as in future turbopump designs, is the utilization of fluid film bearings in lieu of continuous contact bearings. Hydrostatic, hydrodynamic, and damping seal bearings are all replacement candidates for contact bearings in rocket engine high speed turbomachinery. These three types of fluid film bearings have different operating characteristics, but they share a common set of mechanical design opportunities and difficulties. Results of research to define some of the mechanical design issues are given. Problems considered include transient strat/stop rub, non-operational rotor support, bearing wear inspection and measurement, and bearing fluid supply route. Emphasis is given to the HPOTP preburner pump (PBP) bearing, but the results are pertinent to high-speed cryogenic turbomachinery in general.

  1. 7 CFR 761.53 - Interest bearing accounts.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Interest bearing accounts. 761.53 Section 761.53... AGRICULTURE SPECIAL PROGRAMS GENERAL PROGRAM ADMINISTRATION Supervised Bank Accounts § 761.53 Interest bearing accounts. (a) A supervised bank account, if possible, will be established as an interest bearing...

  2. Identification of dynamic properties of radial air-foil bearings

    NARCIS (Netherlands)

    Arora, V.; Hoogt, van der P.J.M.; Aarts, R.G.K.M.; Boer, de A.

    2010-01-01

    Air-foil bearings (AFBs) are self acting hydrodynamic bearings made from sheet metal foils comprised of at least two layers. The innermost ‘‘top foil’’ layer traps a gas pressure film that supports a load while the layer or layers underneath provide an elastic foundation. Air-foil bearings are curre

  3. Frictional torque numbers for ball cup and journal bearings

    NARCIS (Netherlands)

    Ligterink, D.J.

    1982-01-01

    Plastic bearing material wears in ball cup and journal bearings. Contact areas in the ball cup and the journal bearing increase. The frictional torque needed to rotate the ball or journal also increases. When the coefficient of friction is assumed to be constant during wearing out, the frictional t

  4. Frictional torque numbers for ball cup and journal bearings

    OpenAIRE

    Ligterink, D.J.

    1982-01-01

    Plastic bearing material wears in ball cup and journal bearings. Contact areas in the ball cup and the journal bearing increase. The frictional torque needed to rotate the ball or journal also increases. When the coefficient of friction is assumed to be constant during wearing out, the frictional torque increases to a maximum of 1.273 times the frictional torque at zero wear.

  5. Temperature Distribution and Scuffing of Tapered Roller Bearing

    Institute of Scientific and Technical Information of China (English)

    WANG Ailin; WANG Jiugen

    2014-01-01

    In the field of aerospace, high-speed trains and automobile, etc, analysis of temperature filed and scuffing failure of tapered roller bearings are more important than ever, and the scuffing failure of elements of such rolling bearings under heavy load and high speed still cannot be effectively predicted yet. A simplified model of tapered roller bearings consisted of one inner raceway, one outer raceway and a tapered roller was established, in which the interaction of several heat sources is ignored. The contact mechanics model, temperature model and model of scuffing failure are synthesized, and the corresponding computer programs are developed to analyze the effects of bearings parameters, different material and operational conditions on thermal performance of bearings, and temperature distribution and the possibility of surface scuffing are obtained. The results show that load, speed, thermal conductivity and tapered roller materials influence temperature rise and scuffing failure of bearings. Ceramic material of tapered roller results in the decrease of scuffing possibility of bearings to a high extent than the conventional rolling bearing steel. Compared with bulk temperature, flash temperature on the surfaces of bearing elements has a little influence on maximum temperature rise of bearing elements. For the rolling bearings operated under high speed and heavy load, this paper proposes a method which can accurately calculate the possibility of scuffing failure of rolling bearings.

  6. 49 CFR 230.103 - Tender roller bearing journal boxes.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false Tender roller bearing journal boxes. 230.103... Locomotives and Tenders Running Gear § 230.103 Tender roller bearing journal boxes. Tender roller bearing journal boxes shall be maintained in a safe and suitable condition....

  7. Mechatronics Applied to Fluid Film Bearings: Towards More Efficient Machinery

    DEFF Research Database (Denmark)

    Cerda Varela, Alejandro Javier

    Film Bearings: Towards more Efficient Machinery" was aimed at improving the state of the art regarding the usage of fluid film bearings as "smart" machine elements. Specifically, this project dealt with a tilting pad journal bearing design that features a controllable lubrication system, capable...

  8. Low-Wear Ball-Bearing Separator

    Science.gov (United States)

    Hawkinson, Elden L.

    1991-01-01

    Proposed ball-bearing separator for use in cryogenic pump stronger and more resistant to wear. Consists of molded plastic-and-metal composite ring imbued with solid lubricant and containing embedded metal ring. Obtains combination of strength and lubricity. Before molding and machining, ring includes tooling portion for handling and indexing. Molded composite blend of PTFE and fluorinated ethylene/propylene (FEP) filled with brass and bronze powder and molybdenum disulfide powder.

  9. Bearing pad to pressure tube contact simulation

    Energy Technology Data Exchange (ETDEWEB)

    Talebi, F.; Behdadi, A.; Luxat, J.C., E-mail: farshat@mcmaster.ca, E-mail: behdada@mcmaster.ca, E-mail: luxatj@mcmaster.ca [McMaster Univ., Dept. of Engineering Physics, Hamilton, Ontario (Canada)

    2011-07-01

    Thermal creep strain deformation is a very important pressure tube failure mechanism. During a postulated LOCA (loss of coolant accident) with failure of emergency core injection sys- tem (ECIS), the fuel cladding temperature rapidly increases and the pressure tube becomes completely dry in a few seconds after flow stagnation occurs. Subsequently, the pressure tube circumference is heated by thermal radiation except at the spots where the bearing pads are in direct contact with the pressure tube. Therefore, the localized hot spots are developed on the pressure tube's inner surface under the bearing pads. The main objective of this paper is to evaluate the local thermal-mechanical deformation of a pressure tube in a CANDU reactor and to investigate the fuel channel integrity under localized contact between bearing pad and pressure tube. Furthermore, the mechanistic models are validated against the experimental works per- formed at WRL (Whiteshell research laboratory). Calculations are performed using the finite element method in which the heat, thermal mechanical and creep strain equations are solved, simultaneously. According to the experimental set up, the heat conduction from bearing pads to the inner surface of the pressure tube with appropriate convective and radiation boundary conditions has been simulated. Furthermore, the thermal creep strain deformation has been obtained for when the pressure tube is still under operational condition. It is observed that the pressure tube thermal strain will occur if sufficient high temperature is reached however, depending on the severity of flow degradation in the fuel channel, these localized hot spots could represent a potential creep strain failure of the pressure tube. Whether the pressure tube would fail at these hot spots before contacting the calandria tube depends on the localized temperature and experienced pressure transients. Sensitivity analysis is performed in order to evaluate the contact conductance

  10. Existence of equilibria in articulated bearings

    Science.gov (United States)

    Buscaglia, G.; Ciuperca, I.; Hafidi, I.; Jai, M.

    2007-04-01

    The existence of equilibrium solutions for a lubricated system consisting of an articulated body sliding over a flat plate is considered. Though this configuration is very common (it corresponds to the popular tilting-pad thrust bearings), the existence problem has only been addressed in extremely simplified cases, such as planar sliders of infinite width. Our results show the existence of at least one equilibrium for a quite general class of (nonplanar) slider shapes. We also extend previous results concerning planar sliders.

  11. Conservation of brown bear in the Alps: space use and settlement behavior of reintroduced bears

    Science.gov (United States)

    Preatoni, Damiano; Mustoni, Andrea; Martinoli, Adriano; Carlini, Eugenio; Chiarenzi, Barbara; Chiozzini, Simonetta; Van Dongen, Stefan; Wauters, Luc A.; Tosi, Guido

    2005-11-01

    Large carnivores typically need large home ranges containing habitats patches of different quality. Consequently, their conservation requires habitat protection and management at the landscape scale. In some cases, reintroduction might be used to support remnant or restore extinct populations. This is the case for the brown bear ( Ursus arctos) in the Italian Alps. We monitored spacing behavior and settlement of reintroduced brown bears in Adamello-Brenta Natural Park, North-Italy, using radio-tracking. Habitat use, dispersion and survival were studied to evaluate the success of reintroduction and possible conflicts with man. All three males and five of seven females settled in the study area. Most bears roamed widely the first months after release, exploring the new habitat. Patterns of home range overlap between seasons and years revealed that home range use stabilized the year after first hibernation. Home ranges were larger in the mating season (May-July) than in spring or autumn. Home ranges varied between 34 and 1813 km 2 the year after release, but core-areas, where feeding activity was concentrated, were much smaller. Some bears had exclusive core-areas in summer and autumn, but most showed considerable core-area overlap with animals of the same and/or the opposite sex. Bears selected deciduous forests, mixed and conifer forests were used according to availability, and areas with anthropogenic disturbance were avoided. Most bears settled and some reproduced successfully at the release site, causing high initial population growth, suggesting that reintroduction can help to re-establish a brown bear population in the Italian Alps.

  12. Concurrent initialization for Bearing-Only SLAM.

    Science.gov (United States)

    Munguía, Rodrigo; Grau, Antoni

    2010-01-01

    Simultaneous Localization and Mapping (SLAM) is perhaps the most fundamental problem to solve in robotics in order to build truly autonomous mobile robots. The sensors have a large impact on the algorithm used for SLAM. Early SLAM approaches focused on the use of range sensors as sonar rings or lasers. However, cameras have become more and more used, because they yield a lot of information and are well adapted for embedded systems: they are light, cheap and power saving. Unlike range sensors which provide range and angular information, a camera is a projective sensor which measures the bearing of images features. Therefore depth information (range) cannot be obtained in a single step. This fact has propitiated the emergence of a new family of SLAM algorithms: the Bearing-Only SLAM methods, which mainly rely in especial techniques for features system-initialization in order to enable the use of bearing sensors (as cameras) in SLAM systems. In this work a novel and robust method, called Concurrent Initialization, is presented which is inspired by having the complementary advantages of the Undelayed and Delayed methods that represent the most common approaches for addressing the problem. The key is to use concurrently two kinds of feature representations for both undelayed and delayed stages of the estimation. The simulations results show that the proposed method surpasses the performance of previous schemes. PMID:22294884

  13. Concurrent Initialization for Bearing-Only SLAM

    Directory of Open Access Journals (Sweden)

    Antoni Grau

    2010-03-01

    Full Text Available Simultaneous Localization and Mapping (SLAM is perhaps the most fundamental problem to solve in robotics in order to build truly autonomous mobile robots. The sensors have a large impact on the algorithm used for SLAM. Early SLAM approaches focused on the use of range sensors as sonar rings or lasers. However, cameras have become more and more used, because they yield a lot of information and are well adapted for embedded systems: they are light, cheap and power saving. Unlike range sensors which provide range and angular information, a camera is a projective sensor which measures the bearing of images features. Therefore depth information (range cannot be obtained in a single step. This fact has propitiated the emergence of a new family of SLAM algorithms: the Bearing-Only SLAM methods, which mainly rely in especial techniques for features system-initialization in order to enable the use of bearing sensors (as cameras in SLAM systems. In this work a novel and robust method, called Concurrent Initialization, is presented which is inspired by having the complementary advantages of the Undelayed and Delayed methods that represent the most common approaches for addressing the problem. The key is to use concurrently two kinds of feature representations for both undelayed and delayed stages of the estimation. The simulations results show that the proposed method surpasses the performance of previous schemes.

  14. AN INVESTIGATION OF MAGNETIC BEARING SYSTEMS

    Directory of Open Access Journals (Sweden)

    Gürcan SAMTAŞ

    2007-02-01

    Full Text Available The magnetic bearing consists of levitating a shaft so that it is free to rotate about its axis. The magnetic bearing has the advantages of being very quiet work and very cleanliness because there is no mechanical friction or lubricants. The shaft has two permanent magnets attached to it. These two magnets determine a straight line rotation axis of the rotor shaft. The magnets are radially levitated and centered within a cavity by a passive permanent magnetic field in the adding stator housing assembly. The levitation and centering of the shaft axially is stabilized by a closed loop electronic servo circuit that regulates an electromagnetic field in the stator housing that pushes and pulls on the shaft magnets. The rotor weight can be between one gram and forty five thousand, four hundred grams. In 1985, the first magnetic bearing was developed that it had used to applications of gas turbines and other compressors. In these days, they can be used by many applications which are Medical, Transportation, Machine and Tools Industry, Aerospace, Vacuum and Clean room Environments... etc.

  15. Hydrolyzable polyureas bearing hindered urea bonds.

    Science.gov (United States)

    Ying, Hanze; Cheng, Jianjun

    2014-12-10

    Hydrolyzable polymers are widely used materials that have found numerous applications in biomedical, agricultural, plastic, and packaging industrials. They usually contain ester and other hydrolyzable bonds, such as anhydride, acetal, ketal, or imine, in their backbone structures. Here, we report the first design of hydrolyzable polyureas bearing dynamic hindered urea bonds (HUBs) that can reversibly dissociate to bulky amines and isocyanates, the latter of which can be further hydrolyzed by water, driving the equilibrium to facilitate the degradation of polyureas. Polyureas bearing 1-tert-butyl-1-ethylurea bonds that show high dynamicity (high bond dissociation rate), in the form of either linear polymers or cross-linked gels, can be completely degraded by water under mild conditions. Given the simplicity and low cost for the production of polyureas by simply mixing multifunctional bulky amines and isocyanates, the versatility of the structures, and the tunability of the degradation profiles of HUB-bearing polyureas, these materials are potentially of very broad applications. PMID:25406025

  16. Conflict bear translocation: investigating population genetics and fate of bear translocation in Dachigam National Park, Jammu and Kashmir, India.

    Science.gov (United States)

    Mukesh; Sharma, Lalit Kumar; Charoo, Samina Amin; Sathyakumar, Sambandam

    2015-01-01

    The Asiatic black bear population in Dachigam landscape, Jammu and Kashmir is well recognized as one of the highest density bear populations in India. Increasing incidences of bear-human interactions and the resultant retaliatory killings by locals have become a serious threat to the survivorship of black bears in the Dachigam landscape. The Department of Wildlife Protection in Jammu and Kashmir has been translocating bears involved in conflicts, henceforth 'conflict bears' from different sites in Dachigam landscape to Dachigam National Park as a flagship activity to mitigate conflicts. We undertook this study to investigate the population genetics and the fate of bear translocation in Dachigam National Park. We identified 109 unique genotypes in an area of ca. 650 km2 and observed bear population under panmixia that showed sound genetic variability. Molecular tracking of translocated bears revealed that mostly bears (7 out of 11 bears) returned to their capture sites, possibly due to homing instincts or habituation to the high quality food available in agricultural croplands and orchards, while only four bears remained in Dachigam National Park after translocation. Results indicated that translocation success was most likely to be season dependent as bears translocated during spring and late autumn returned to their capture sites, perhaps due to the scarcity of food inside Dachigam National Park while bears translocated in summer remained in Dachigam National Park due to availability of surplus food resources. Thus, the current management practices of translocating conflict bears, without taking into account spatio-temporal variability of food resources in Dachigam landscape seemed to be ineffective in mitigating conflicts on a long-term basis. However, the study highlighted the importance of molecular tracking of bears to understand their movement patterns and socio-biology in tough terrains like Dachigam landscape.

  17. Conflict bear translocation: investigating population genetics and fate of bear translocation in Dachigam National Park, Jammu and Kashmir, India.

    Directory of Open Access Journals (Sweden)

    Mukesh

    Full Text Available The Asiatic black bear population in Dachigam landscape, Jammu and Kashmir is well recognized as one of the highest density bear populations in India. Increasing incidences of bear-human interactions and the resultant retaliatory killings by locals have become a serious threat to the survivorship of black bears in the Dachigam landscape. The Department of Wildlife Protection in Jammu and Kashmir has been translocating bears involved in conflicts, henceforth 'conflict bears' from different sites in Dachigam landscape to Dachigam National Park as a flagship activity to mitigate conflicts. We undertook this study to investigate the population genetics and the fate of bear translocation in Dachigam National Park. We identified 109 unique genotypes in an area of ca. 650 km2 and observed bear population under panmixia that showed sound genetic variability. Molecular tracking of translocated bears revealed that mostly bears (7 out of 11 bears returned to their capture sites, possibly due to homing instincts or habituation to the high quality food available in agricultural croplands and orchards, while only four bears remained in Dachigam National Park after translocation. Results indicated that translocation success was most likely to be season dependent as bears translocated during spring and late autumn returned to their capture sites, perhaps due to the scarcity of food inside Dachigam National Park while bears translocated in summer remained in Dachigam National Park due to availability of surplus food resources. Thus, the current management practices of translocating conflict bears, without taking into account spatio-temporal variability of food resources in Dachigam landscape seemed to be ineffective in mitigating conflicts on a long-term basis. However, the study highlighted the importance of molecular tracking of bears to understand their movement patterns and socio-biology in tough terrains like Dachigam landscape.

  18. Development and Evaluation of Titanium Space Suit Bearings

    Science.gov (United States)

    Rhodes, Richard; Battisti, Brian; Ytuarte, Ray, Jr.; Schultz, Bradley

    2016-01-01

    The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z series space suit architecture allows us to reduce mass by an estimated 23 pounds per suit system compared to the previously used stainless steel bearing designs without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race: 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approximately 2 years), bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination around a maximum contact stress that will allow the bearing to survive the life of an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an exploration mission.

  19. Unbalance Response Prediction for Rotors on Ball Bearings Using Speed- and Load-Dependent Nonlinear Bearing Stiffness

    Directory of Open Access Journals (Sweden)

    Fleming David P.

    2005-01-01

    Full Text Available Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus, an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work, bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant-stiffness bearings. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

  20. Bearing life in contaminated oil and oil passing into bearing for tapered roller bearing; Ensui koro jikuuke ni okeru ibutsu yuchu deno jumyo to kantsu yuryo

    Energy Technology Data Exchange (ETDEWEB)

    Asai, Y.; Oshima, H.; Sakamoto, K. [Koyo Seiko Co. Ltd., Osaka (Japan)

    1997-10-01

    In this paper a relationship between depth of dents, area of dents gathered and bearing life has been investigated for tapered roller bearings used in differential gear case. It is effective for the longer bearing life to reduce hard particles of Fe especially among several contaminations existing in the gear case. It is also effective to make oil level lower in the case from the view point for reduction of number of dents. 8 refs., 8 figs., 4 tabs.

  1. Gerotor and bearing system for whirling mass orbital vibrator

    Science.gov (United States)

    Brett, James Ford; Westermark, Robert Victor; Turner, Jr., Joey Earl; Lovin, Samuel Scott; Cole, Jack Howard; Myers, Will

    2007-02-27

    A gerotor and bearing apparatus for a whirling mass orbital vibrator which generates vibration in a borehole. The apparatus includes a gerotor with an inner gear rotated by a shaft having one less lobe than an outer gear. A whirling mass is attached to the shaft. At least one bearing is attached to the shaft so that the bearing engages at least one sleeve. A mechanism is provided to rotate the inner gear, the mass and the bearing in a selected rotational direction in order to cause the mass, the inner gear, and the bearing to backwards whirl in an opposite rotational direction. The backwards whirling mass creates seismic vibrations.

  2. Stability of multi orifice active tilting-pad journal bearings

    DEFF Research Database (Denmark)

    Haugaard, Asger M.; Santos, Ilmar

    2010-01-01

    The stability properties of actively lubricated tilting-pad journal bearings are investigated theoretically. The bearing preload factor and control system gains are varied, and stable and unstable regions are identified. It is seen, that the control system influences bearing stability......, and that the nature and magnitude of this influence depends on the rotor mass, preload factor and rotational speed. Furthermore, it is shown that assuming the bearing pads to be rigid can produce a substantial error. A rigid pad model will overpredict the stable range of the bearing, thus it may lead to failure...

  3. Relationship of rolling bearing stiffness with diameter of roller

    Institute of Scientific and Technical Information of China (English)

    郭茂林; 王刚; 张瑞

    2002-01-01

    The theoretical formula of roller bearing stiffness is induced and compared with its empirical formula.In the experience formula the stiffness of roller bearing has nothing to do with the roller diameter. The relation-ship of roller bearing stiffness with roller diameter was studied using Hz contacting theory. It is concluded thatconclusion in experience formula is only approximate result of data processing under special conditions, and therelation between stiffness of roller bearing and roller diameter must be taken into consideration while designingor selecting roller bearings.

  4. Sudden venting test of an emergency bearing for the magnet bearing type compound molecular pump

    International Nuclear Information System (INIS)

    The vacuum evacuation system for nuclear fusion reactors bears the role of exhausting hydrogen isotopes in large quantity together with helium continuously for long hours, and as the high vacuum pumps for this purpose, the mechanical pumps which can do continuous evacuation and decrease the quantity of staying radioactive tritium, such as turbo molecular pumps and compound molecular pumps, are promising. Because of the compatibility with tritium, oil lubrication is not desirable, accordingly, the pumps with ceramic rotating vanes and magnetic bearings are demanded. As a part of the development of a magnetic bearing type mechanical pump which can be used for nuclear fusion reactors, the compound molecular pump, in which emergency bearings were incorporated, was made for trial, and the test of sudden air intrusion was carried out, as the results, various knowledges were obtained. The constitution of the testing setup, and the test results are reported. When air was injected at the pressure rise of 3.3x104 Pa/s from exhaust port side, after about 2.5 s, the maximum lift of 4.2x103 N arose. When air was injected at the pressure rise of 2.7x105 Pa/s from the suction part side, after about 0.4s, the maximum lift of 6.9x103 N arose. In the air injection alternately from the suction port and exhaust port sides, the emergency bearings functioned normally in 10 times of the test. (K.I.)

  5. Exciton diffusion length in some thermocleavable polythiophenes by the surface photovoltage method

    DEFF Research Database (Denmark)

    Tousek, J.; Touskova, J.; Remes, Z.;

    2012-01-01

    obtained from transmittance and reflectance spectra. Our method of surface photovoltage extended to thin semiconducting layers was utilized for extraction of diffusion length of photogenerated excitons. Higher diffusion lengths in P3CT and PT materials as compared with that in P3MHOCT can probably...

  6. Preparation of thermocleavable conjugates based on ansamitocin and superparamagnetic nanostructured particles by a chemobiosynthetic approach.

    Science.gov (United States)

    Mancuso, Lena; Knobloch, Tobias; Buchholz, Jessica; Hartwig, Jan; Möller, Lena; Seidel, Katja; Collisi, Wera; Sasse, Florenz; Kirschning, Andreas

    2014-12-22

    A combination of mutasynthesis, precursor-directed biosynthesis and semisynthesis provides access to new ansamitocin derivatives including new nanostructured particle-drug conjugates. These conjugates are based on the toxin ansamitocin and superparamagnetic iron oxide-silica core shell particles. New ansamitocin derivatives that are functionalized either with alkynyl- or azido groups in the ester side chain at C-3 are attached to nanostructured iron oxide core-silica shell particles. Upon exposure to an oscillating electromagnetic field these conjugates heat up and the ansamitocin derivatives are released by a retro-Diels-Alder reaction. For example, one ansamitocin derivative exerts strong antiproliferative activity against various cancer cell lines in the lower nanomolar range while the corresponding nanostructured particle-drug conjugate is not toxic. Therefore, these new conjugates can serve as dormant toxins that can be employed simultaneously in hyperthermia and chemotherapy when external inductive heating is applied. PMID:25346489

  7. Thermocleavable π‐Conjugated Polymers – Synthesis and photovoltaic applications

    OpenAIRE

    Petersen, Martin Helgesen

    2009-01-01

    Polymer solar cells (plastic solar cells) have seen remarkable improvements in recent years where power conversion efficiencies of up to 6% have been reported for small area devices. However in terms of stability polymer solar cells degrade during illumination and in the dark leading to operational lifetimes that are generally very poor. There has been a recent interest in the operational stability of devices and more importantly on the understanding of why devices and materials break down. T...

  8. Misalignment in Gas Foil Journal Bearings: An Experimental Study

    Science.gov (United States)

    Howard, Samuel A.

    2008-01-01

    As gas foil journal bearings become more prevalent in production machines, such as small gas turbine propulsion systems and microturbines, system-level performance issues must be identified and quantified in order to provide for successful design practices. Several examples of system-level design parameters that are not fully understood in foil bearing systems are thermal management schemes, alignment requirements, balance requirements, thrust load balancing, and others. In order to address some of these deficiencies and begin to develop guidelines, this paper presents a preliminary experimental investigation of the misalignment tolerance of gas foil journal bearing systems. Using a notional gas foil bearing supported rotor and a laser-based shaft alignment system, increasing levels of misalignment are imparted to the bearing supports while monitoring temperature at the bearing edges. The amount of misalignment that induces bearing failure is identified and compared to other conventional bearing types such as cylindrical roller bearings and angular contact ball bearings. Additionally, the dynamic response of the rotor indicates that the gas foil bearing force coefficients may be affected by misalignment.

  9. Rolling Bearing Steels - A Technical and Historical Perspective

    Science.gov (United States)

    Zaretsky, Erwin V.

    2012-01-01

    Starting about 1920 it becomes easier to track the growth of bearing materials technology. Until 1955, with few exceptions, comparatively little progress was made in this area. AISI 52100 and some carburizing grades (AISI 4320, AISI 9310) were adequate for most applications. The catalyst to quantum advances in high-performance rolling-element bearing steels was the advent of the aircraft gas turbine engine. With improved bearing manufacturing and steel processing together with advanced lubrication technology, the potential improvements in bearing life can be as much as 80 times that attainable in the late 1950s or as much as 400 times that attainable in 1940. This paper summarizes the chemical, metallurgical and physical aspects of bearing steels and their effect on rolling bearing life and reliability. The single most important variable that has significantly increased bearing life and reliability is vacuum processing of bearing steel. Differences between through hardened, case carburized and corrosion resistant steels are discussed. The interrelation of alloy elements and carbides and their effect on bearing life are presented. An equation relating bearing life, steel hardness and temperature is given. Life factors for various steels are suggested and discussed. A relation between compressive residual stress and bearing life is presented. The effects of retained austenite and grain size are discussed.

  10. Analysis of thermoelastohydrodynamic performance of journal misaligned engine main bearings

    Science.gov (United States)

    Bi, Fengrong; Shao, Kang; Liu, Changwen; Wang, Xia; Zhang, Jian

    2015-05-01

    To understand the engine main bearings' working condition is important in order to improve the performance of engine. However, thermal effects and thermal effect deformations of engine main bearings are rarely considered simultaneously in most studies. A typical finite element model is selected and the effect of thermoelastohydrodynamic(TEHD) reaction on engine main bearings is investigated. The calculated method of main bearing's thermal hydrodynamic reaction and journal misalignment effect is finite difference method, and its deformation reaction is calculated by using finite element method. The oil film pressure is solved numerically with Reynolds boundary conditions when various bearing characteristics are calculated. The whole model considers a temperature-pressure-viscosity relationship for the lubricant, surface roughness effect, and also an angular misalignment between the journal and the bearing. Numerical simulations of operation of a typical I6 diesel engine main bearing is conducted and importance of several contributing factors in mixed lubrication is discussed. The performance characteristics of journal misaligned main bearings under elastohydrodynamic(EHD) and TEHD loads of an I6 diesel engine are received, and then the journal center orbit movement, minimum oil film thickness and maximum oil film pressure of main bearings are estimated over a wide range of engine operation. The model is verified through the comparison with other present models. The TEHD performance of engine main bearings with various effects under the influences of journal misalignment is revealed, this is helpful to understand EHD and TEHD effect of misaligned engine main bearings.

  11. Potential energetic effects of mountain climbers on foraging grizzly bears

    Science.gov (United States)

    White, D.; Kendall, K.C.; Picton, H.D.

    1999-01-01

    Most studies of the effects of human disturbance on grizzly bears (Ursus arctos horribilis) have not quantified the energetic effects of such interactions. In this study, we characterized activity budgets of adult grizzly bears as they foraged on aggregations of adult army cutworm moths (Euxoa auxiliaris) in the alpine of Glacier National Park, Montana, during 1992, 1994, and 1995. We compared the activity budgets of climber-disturbed bears to those of undisturbed bears to estimate the energetic impact of climber disturbance. When bears detected climbers, they subsequently spent 53% less time foraging on moths, 52% more time moving within the foraging area, and 23% more time behaving aggressively, compared to when they were not disturbed. We estimated that grizzly bears could consume approximately 40,000 moths/day or 1,700 moths/hour. At 0.44 kcal/moth, disruption of moth feeding cost bears approximately 12 kcal/minute in addition to the energy expended in evasive maneuvers and defensive behaviors. To reduce both climber interruption of bear foraging and the potential for aggressive bear-human encounters, we recommend routing climbers around moth sites used by bears or limiting access to these sites during bear-use periods.

  12. Effects of exotic species on Yellowstone's grizzly bears

    Science.gov (United States)

    Reinhart, D.P.; Haroldson, Mark A.; Mattson, D.J.; Gunther, Kerry A.

    2001-01-01

    Humans have affected grizzly bears (Ursus arctos horribilis) by direct mortality, competition for space and resources, and introduction of exotic species. Exotic organisms that have affected grizzly bears in the Greater Yellowstone Area include common dandelion (Taraxacum officinale), nonnative clovers (Trifolium spp.), domesticated livestock, bovine brucellosis (Brucella abortus), lake trout (Salvelinus namaycush), and white pine blister rust (Cronartium ribicola). Some bears consume substantial amounts of dandelion and clover. However, these exotic foods provide little digested energy compared to higher-quality bear foods. Domestic livestock are of greater energetic value, but use of this food by bears often leads to conflicts with humans and subsequent increases in bear mortality. Lake trout, blister rust, and brucellosis diminish grizzly bears foods. Lake trout prey on native cutthroat trout (Oncorhynchus clarkii) in Yellowstone Lake; white pine blister rust has the potential to destroy native whitebark pine (Pinus albicaulis) stands; and management response to bovine brucellosis, a disease found in the Yellowstone bison (Bison bison) and elk (Cervus elaphus), could reduce populations of these 2 species. Exotic species will likely cause more harm than good for Yellowstone grizzly bears. Managers have few options to mitigate or contain the impacts of exotics on Yellowstones grizzly bears. Moreover, their potential negative impacts have only begun to unfold. Exotic species may lead to the loss of substantial highquality grizzly bear foods, including much of the bison, trout, and pine seeds that Yellowstone grizzly bears currently depend upon.

  13. Physiologic responses of grizzly bears to different methods of capture.

    Science.gov (United States)

    Cattet, Marc R; Christison, Katina; Caulkett, Nigel A; Stenhouse, Gordon B

    2003-07-01

    The physiologic effects of two methods of capture, chemical immobilization of free-ranging (FR) bears by remote injection from a helicopter and physical restraint (PR) by leg-hold snare prior to chemical immobilization, were compared in 46 grizzly bears (Ursus arctos) handled during 90 captures between 1999 and 2001. Induction dosages and times were greater for FR bears than PR bears, a finding consistent with depletion of, or decreased sensitivity to, catecholamines. Free-ranging bears also had higher rectal temperatures 15 min following immobilization and temperatures throughout handling that correlated positively with induction time. Physically restrained bears had higher white blood cell counts, with more neutrophils and fewer lymphocytes and eosinophils, than did FR bears. This white blood cell profile was consistent with a stress leukogram, possibly affected by elevated levels of serum cortisol. Serum concentrations of alanine aminotransferase, aspartate aminotransferase, and creatine kinase were higher in PR bears that suggested muscle injury. Serum concentrations of sodium and chloride also were higher in PR bears and attributed to reduced body water volume through water deprivation and increased insensible water loss. Overall, different methods of capture resulted in different patterns of physiologic disturbance. Reducing pursuit and drug induction times should help to minimize increase in body temperature and alteration of acid-base balance in bears immobilized by remote injection. Minimizing restraint time and ensuring snare-anchoring cables are short should help to minimize loss of body water and prevent serious muscle injury in bears captured by leg-hold snare.

  14. Marshall Space Flight Center High Speed Turbopump Bearing Test Rig

    Science.gov (United States)

    Gibson, Howard; Moore, Chip; Thom, Robert

    2000-01-01

    The Marshall Space Flight Center has a unique test rig that is used to test and develop rolling element bearings used in high-speed cryogenic turbopumps. The tester is unique in that it uses liquid hydrogen as the coolant for the bearings. This test rig can simulate speeds and loads experienced in the Space Shuttle Main Engine turbopumps. With internal modifications, the tester can be used for evaluating fluid film, hydrostatic, and foil bearing designs. At the present time, the test rig is configured to run two ball bearings or a ball and roller bearing, both with a hydrostatic bearing. The rig is being used to evaluate the lifetimes of hybrid bearings with silicon nitride rolling elements and steel races.

  15. Effect of fluid compressibility on journal bearing performance

    Energy Technology Data Exchange (ETDEWEB)

    Dimofte, F. (NASA, Lewis Research Center, Cleveland, OH (United States))

    1993-07-01

    An analysis was undertaken to determine the effect of fluid film compressibility on the performance of fluid film bearings. A new version of the Reynolds equation was developed, using a polytropic expansion, for both steady-state and dynamic conditions. Polytropic exponents from 1 (isothermal) to 1000 (approaching an incompressible liquid) were evaluated for two bearing numbers, selected from a range of practical interest for cryogenic application, and without cavitation. Bearing loads were insensitive to fluid compressibility for low bearing numbers, as was expected. The effect of compressibility on attitude angle was significant, even when the bearing number was low. A small amount of fluid compressibility was enough to obtain stable running conditions. Incompressible liquid lacked stability at all conditions. Fluid compressibility can be used to control the bearing dynamic coefficients, thereby influencing the dynamic behavior of the rotor-bearing system. 14 refs.

  16. Research of Two Different Impulsive Faults of Rolling Element Bearing

    Science.gov (United States)

    Jiang, Zhinong; Xing, Chenghong; Feng, Kun; Gao, Jinji

    2012-05-01

    Fans and pumps are key machines in process industries such as petrochemical and petroleum industries. Their faults can be catastrophic and result in costly downtime. Bearing fault is almost the most common fault of fans and pumps as rolling element bearings are widely used in these machines. Hence, condition monitoring and diagnosis of bearings are important. Two different impulsive faults of bearings have been observed and studied in previous research. The first fault presents very clear impulsive symptom in envelope spectrum, but the bearing can work for a long time. The other fault shows relatively indistinct symptom, but the bearing will break down in a short time. To overcome the problems of inaccurate diagnosis, a combinational approach based on an impulsive energy indicator and traditional enveloping analysis is proposed in this paper. This approach discriminate these two faults well and can support the maintenance decision for the machines with rolling element bearings.

  17. On the computation of electrical resistance of hydrodynamic journal bearing

    Directory of Open Access Journals (Sweden)

    Eleonora Pop

    2014-12-01

    Full Text Available The paper approaches the mathematical model of electrical resistance of hydrodynamic journal bearing under different parameters of operation so as to predict bearing performance and safe load carrying capacity. The currents circulating in the journal bearing of electrical machine causes reducing of lifespan by appearance of pitting on their surface and the degradation of the lubricant. In a hydrodynamic journal bearing, the zone of minimum film thickness, load-carrying oil film varies along the circumference of a bearing through its length. This has been found to form a capacitor of varying capacitance between the journal and the bearings dependent on permittivity of the lubricant used, the bearing length, the eccentricity ratio and the clearance ratio. Besides this, load-carrying on oil film offers resistance that depends on operating parameters and resistivity of the lubricant.

  18. Computer-aided selection of materials for cryogenic turbopump bearings

    Science.gov (United States)

    Maurer, R. E.; Pallini, R. A.

    1985-01-01

    The life requirement for the angular contact ball bearings in the Space Shuttle Main Engine (SSME) high-pressure-oxygen turbopump (HPOTP) is 7.5 hours. In actual operation, significantly shorter service life has been experienced. The objective of this current program is to identify bearing materials and/or materials processing techniques offering significant potential for extending HPOTP bearing performance life. A thermomechanical analysis of the HPOTP shaft/bearing system was performed with the SHABERTH (SHaft-BEaring-THermal) computer program. Bearing fatigue life, ball-race contact stress, heat generation rate, bulk ring temperatures, and circumferential stress in the inner rings were quantified as functions of radial load, thrust load, and ball-race contact friction. The analysis results were used to formulate criteria that are being used for the selection of special materials for future turbopump bearings.

  19. Cyclostationary Analysis for Gearbox and Bearing Fault Diagnosis

    Directory of Open Access Journals (Sweden)

    Zhipeng Feng

    2015-01-01

    Full Text Available Gearbox and rolling element bearing vibration signals feature modulation, thus being cyclostationary. Therefore, the cyclic correlation and cyclic spectrum are suited to analyze their modulation characteristics and thereby extract gearbox and bearing fault symptoms. In order to thoroughly understand the cyclostationarity of gearbox and bearing vibrations, the explicit expressions of cyclic correlation and cyclic spectrum for amplitude modulation and frequency modulation (AM-FM signals are derived, and their properties are summarized. The theoretical derivations are illustrated and validated by gearbox and bearing experimental signal analyses. The modulation characteristics caused by gearbox and bearing faults are extracted. In faulty gearbox and bearing cases, more peaks appear in cyclic correlation slice of 0 lag and cyclic spectrum, than in healthy cases. The gear and bearing faults are detected by checking the presence or monitoring the magnitude change of peaks in cyclic correlation and cyclic spectrum and are located according to the peak cyclic frequency locations or sideband frequency spacing.

  20. Gonadorelin at the outset and/or end of an ovulation synchronization progesterone estradiol benzoate-based protocol in Nellore females

    Directory of Open Access Journals (Sweden)

    Carla Cristian Campos

    2016-02-01

    Full Text Available This study aimed to evaluate the effects of gonadorelin (GnRH, used both at the outset of a timed artificial insemination (TAI protocol to synchronize follicular wave recruitment and at the end to synchronize ovulation, on the conception rate (CR in Nellore cows. The experiment was conducted on two beef cattle farms in the Vale do Araguaia, MT. The body condition score (BCS evaluation and ultrasound examination to determine ovarian status [follicle diameter < 10 mm, ? 10 mm or presence of corpus luteum (CL] were performed at the beginning (Day 0 of the TAI protocol. Multiparous cows (n = 494 were subjected to the following protocol: Day 0 – insertion of intravaginal progesterone device (P4 DIB®, MSD previously used for 8 or 16 days and IM administration of 2.0 mg of estradiol benzoate (EB, Gonadiol®, MSD; Day 8 – P4 device withdrawal, IM injection of 300 IU of equine chorionic gonadotropin (eCG, Folligon®, MSD, 1.0 mg of estradiol cypionate (ECP®, Zoetis and 0.265 mg of Sodium cloprostenol (PGF2?, Ciosin®, MSD; Day 10 – TAI, performed by a single inseminator. Animals were randomly assigned to one of four groups: control (n = 126, GnRH D0 (n = 123, GnRH D10 (n = 123 and GnRH D0 + D10 (n = 122. Animals treated with GnRH received 50 mcg of gonadorelin (GnRH, Cystorelin®, Merial. Pregnancy was diagnosed by ultrasound 39 ± 10 days after TAI. Data were analyzed using the GLIMMIX procedure of SAS program (P < 0.05. The overall CR was 42.71%. Effect of treatment was not detected (P = 0.2482 on CR, which was 36.89% ± 0.19 (47/126 for the control group, 46.08% ± 0.19 (56/123 for GnRH D0, 48.30% ± 0.18 (61/123 for GnRH D10 and 38.48% ± 0.19 (47/122 for GnRH D0 + D10. An effect of farm was detected; the CR was 47.32% ± 0.13 at Farm A and was 38.24% ± 0.13 at Farm B (P = 0.0249. No effects of the interaction between farm and treatment were observed (P = 0.7662, nor of those among ovarian condition and treatment (P = 0.1225 on CR. Cows with

  1. HPLC法测定氨酚麻美糖浆中苯甲酸钠的含量%Determination of Sodium Benzoate in Paracetamol, Pseudoephedrine Hydrochloride and Dextromethorphane Syrup by HPLC

    Institute of Scientific and Technical Information of China (English)

    张瑜; 卢丹; 王冬

    2014-01-01

    目的:建立氨酚麻美糖浆中苯甲酸钠含量测定方法。方法:采用HPLC法测定,色谱柱为Thermo C18(4.6 mm ×100 mm,2.4μm),流动相为0.05 mol· L-1磷酸二氢钾溶液(用磷酸调节pH值至3.5±0.1)-甲醇(38∶62),检测波长为215 nm,进样量2μL。结果:苯甲酸钠在40.14~281.01μg· mL-1浓度范围内线性关系良好,平均回收率为99.0%( RSD=1.5%)。结论:所建方法专属性好,准确,重复性好,可为氨酚麻美糖浆中有效检测防腐剂苯甲酸钠的含量提供参考。%Objective:To establish an HPLC method for determining the content of sodium benzoate in paracetamol , pseudoephedrine hydrochloride and dextromethorphane syrup.Methods:The determination was performed on a column Thermo C 18 (4.6 mm ×100 mm, 2.4 μm) with a mixture of 0.05 mol· L-1 potassium dihydrogenphosphate solution (adjusted pH with phosphoric acid to 3.5 ±0.1) and methanol (38∶62) as mobile phase, the wavelength was 215 nm and the injection volume was 2μL.Results:A good linearity was obtained in range of 40.14-281.01 μg · mL-1 of sodium benzoate and the average recovery was 99.0%( RSD=1.5%) .Conclu-sion:This method is specific and accurate with good repeatability.It would take a good role in the control of sodium benzoate in their mixture syrup.

  2. Performance of passive target tracking using bearing-frequency and bearings of multiple arrays

    Institute of Scientific and Technical Information of China (English)

    DU Xuanmin; YAO Lan

    2002-01-01

    Two target motion analysis (TMA) methods using multi-dimension information are studied, one is TMA with bearing-frequency and the other is TMA with multiple arrays. The optimization algorithm combining Gauss-Newton (G-N) method with Levenberg-Marquardt(LM) method is applied to analyze the performance of target tracking with maximum likelihood estimation(MLE), and Monte Carlo experiments are presented. The results show that although the TMA with multi-dimension information have eliminated the maneuvers needed by conventional bearing-only TMA, but the application are not of universality.

  3. Trophic cascades from wolves to grizzly bears or changing abundance of bears and alternate foods?

    Science.gov (United States)

    Barber-Meyer, Shannon M

    2015-05-01

    This is a Forum article commenting on: Ripple, W. J., Beschta, R. L., Fortin, J. K., & Robbins, C. T. (2014) Trophic cascades from wolves to grizzly bears in Yellowstone. Journal of Animal Ecology, 83, 223-233. Comparisons Ripple et al. (2014) used to demonstrate increased fruit availability and consumption by grizzly bears post-wolf reintroduction are flawed and tenuous at best. Importantly, a more parsimonious (than trophic cascades) hypothesis, not sufficiently considered by Ripple et al., exists and is better supported by available data I review.

  4. Serologic survey of Toxoplasma gondii in grizzly bears (Ursus arctos) and black bears (Ursus americanus), from Alaska, 1988 to 1991.

    Science.gov (United States)

    Chomel, B B; Zarnke, R L; Kasten, R W; Kass, P H; Mendes, E

    1995-10-01

    We tested 644 serum samples from 480 grizzly bears and 40 black bears from Alaska (USA), collected between 1988 and 1991, for Toxoplasma gondii antibodies, using a commercially available latex agglutination test (LAT). A titer > or = 64 was considered positive. Serum antibody prevalence for T. gondii in grizzly bears (Ursus arctos) was 18% (87 of 480). Prevalence ranged from 9% (seven of 77) on Kodiak Island to 28% (15 of 54) in northern Alaska. Prevalence was directly correlated to age. No grizzly bears grizzly bears captured north of the Arctic Circle. Antibody prevalence in black bears (Ursus americanus) from Interior Alaska was 15% (six of 40), similar to the prevalence in grizzly bears from the same area (13%; five of 40).

  5. Method of recertifying a loaded bearing member

    Science.gov (United States)

    Allison, Sidney G. (Inventor)

    1992-01-01

    A method is described of recertifying a loaded bearing member using ultrasound testing to compensate for different equipment configurations and temperature conditions. The standard frequency F1 of a reference block is determined via an ultrasonic tone burst generated by a first pulsed phased locked loop (P2L2) equipment configuration. Once a lock point number S is determined for F1, the reference frequency F1a of the reference block is determined at this lock point number via a second P2L2 equipment configuration to permit an equipment offset compensation factor Fo1=((F1-F1a)/F1)(1000000) to be determined. Next, a reference frequency F2 of the unloaded bearing member is determined using a second P2L2 equipment configuration and is then compensated for equipment offset errors via the relationship F2+F2(Fo1)/1000000. A lock point number b is also determined for F2. A resonant frequency F3 is determined for the reference block using a third P2L2 equipment configuration to determine a second offset compensation factor F02=((F1-F3)/F1) 1000000. Next the resonant frequency F4 of the loaded bearing member is measured at lock point number b via the third P2L2 equipment configuration and the bolt load determined by the relationship (-1000000)CI(((F2-F4)/F2)-Fo2), wherein CI is a factor correlating measured frequency shift to the applied load. Temperature compensation is also performed at each point in the process.

  6. Flexure Based Linear and Rotary Bearings

    Science.gov (United States)

    Voellmer, George M. (Inventor)

    2016-01-01

    A flexure based linear bearing includes top and bottom parallel rigid plates; first and second flexures connecting the top and bottom plates and constraining exactly four degrees of freedom of relative motion of the plates, the four degrees of freedom being X and Y axis translation and rotation about the X and Y axes; and a strut connecting the top and bottom plates and further constraining exactly one degree of freedom of the plates, the one degree of freedom being one of Z axis translation and rotation about the Z axis.

  7. Bear Creek Project. Final environmental statement

    International Nuclear Information System (INIS)

    The Bear Creek Project consists of certain mining and milling operations involving uranium ore deposits located in Converse County, Wyoming. Mining of uranium from nine known ore bodies will take place over a period of ten years (estimated); a mill with a nominal capacity of 1000 tons per day of ore will be constructed and operated as long as ore is available. The waste material (tailings) from the mill, also produced at a rate of about 1000 tons per day, will be stored onsite in an impoundment. Environmental impacts and adverse effects are summarized

  8. Carbon Segregation of Bearing Steel Concasting Billet

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    The formation mechanism of “white band” and central carbon segregation of high-carbon Cr bearing steel concasting billets are discussed in this paper. The maximum oxygen content in the steel produced by concasting process was 13x10-6 with an average oxygen content of 9.3x 10-6.Comparison of metallurgical quality and fatigue property between the concasting steel (CC) andingot casting steel (IC) showed that the carbon segregation (C/C0) in former steel was 0.92~1.10and its fatigue life was equal to that of the latter steel.

  9. Titanium Content Control for Bearing Steel

    Institute of Scientific and Technical Information of China (English)

    WU Wei; LIU Yue; LIU Liu; XUE Zheng-liang

    2008-01-01

    On the basis of the thermodynamic analysis and fundamental study in the laboratory,the equilibrium of the Ti-Al-O system was investigated.The results showed that the equilibrium titanium content in the steel increased with the increase in the soluble aluminum content in the steel and the TiO2 content in the slag.Although the slag basicity decreased and Al2O3 content in the slag increased,the titanium content increased.Based on these results,the BOF smelting process of low titanium bearing steel was put forward.

  10. Bearing capacity of mixed soil model

    Directory of Open Access Journals (Sweden)

    Mehdi Khodashenas Pelkoo

    2009-01-01

    Full Text Available The main objective of this research is improvement of red soil with addition of construction materials. This method could provide a scientific way to create a soil foundation with sufficient stability against geo-technical problems or instabilities. Laboratory tests have been conducted to assess the behavior of red soil, when amended with different types of gravels, soils and sand under compacted conditions with Optimum Moisture Content (OMC. Safe bearing capacity of all models, have been calculated to identify best and worst soil mixed model.

  11. Coronal properties of planet-bearing stars

    OpenAIRE

    Poppenhaeger, K.; Robrade, J.; Schmitt, J. H. M. M.

    2010-01-01

    Do extrasolar planets affect the activity of their host stars? Indications for chromospheric activity enhancement have been found for a handful of targets, but in the X-ray regime, conclusive observational evidence is still missing. We want to establish a sound observational basis to confirm or reject major effects of Star-Planet Interactions (SPI) in stellar X-ray emissions. We therefore conduct a statistical analysis of stellar X-ray activity of all known planet-bearing stars within 30pc di...

  12. Estimating Potential Effects of Hypothetical Oil Spills on Polar Bears

    Science.gov (United States)

    Amstrup, Steven C.; Durner, G.M.; McDonald, T.L.; Johnson, W.R.

    2006-01-01

    Much is known about the transport and fate of oil spilled into the sea and its toxicity to exposed wildlife. Previously, however, there has been no way to quantify the probability that wildlife dispersed over the seascape would be exposed to spilled oil. Polar bears, the apical predator of the arctic, are widely dispersed near the continental shelves of the Arctic Ocean, an area also undergoing considerable hydrocarbon exploration and development. We used 15,308 satellite locations from 194 radiocollared polar bears to estimate the probability that polar bears could be exposed to hypothetical oil spills. We used a true 2 dimensional Gausian kernel density estimator, to estimate the number of bears likely to occur in each 1.00 km2 cell of a grid superimposed over near shore areas surrounding 2 oil production facilities: the existing Northstar oil production facility, and the proposed offshore site for the Liberty production facility. We estimated the standard errors of bear numbers per cell with bootstrapping. Simulated oil spill footprints for September and October, the times during which we hypothesized effects of an oil-spill would be worst, were estimated using real wind and current data collected between 1980 and 1996. We used ARC/Info software to calculate overlap (numbers of bears oiled) between simulated oil-spill footprints and polar bear grid-cell values. Numbers of bears potentially oiled by a hypothetical 5912 barrel spill (the largest spill thought probable from a pipeline breach) ranged from 0 to 27 polar bears for September open water conditions, and from 0 to 74 polar bears in October mixed ice conditions. Median numbers oiled by the 5912 barrel hypothetical spill from the Liberty simulation in September and October were 1 and 3 bears, equivalent values for the Northstar simulation were 3 and 11 bears. In October, 75% of trajectories from the 5912 barrel simulated spill at Liberty oiled 9 or fewer bears while 75% of the trajectories affected 20 or

  13. The Giant Magellan telescope (GMT): Gregorian instrument rotator bearing

    Science.gov (United States)

    Gunnels, Steve

    2014-07-01

    The Giant Magellan Telescope (GMT) is an optical-infrared 25 Meter ELT to be located in Chile. It is being designed and constructed by a group of U.S. and international universities and research institutions. The Gregorian Instrument Rotator (GIR) for GMT will be a structural-mechanical assembly 9.4 meters in diameter and 6.9 meters long. The complete assembly including structure, instruments and mechanisms has a rotating mass of 117,000 kg. It will be supported by a unique bearing system using high-capacity precision industrial rollers. The rollers will support the GIR via two large hardened and ground runner bearings integral with the structure. The bearing system includes an upper axial bearing with (8) rollers and an upper and lower radial bearing, each using (10) identical rollers. The bearing system will have the advantages of adjustability, low friction, low noise (jitter), and low cost. The rollers have a manufacturer-rated capacity 4 times greater than their maximum working load in GMT. It is important that the hardened runner bearings have a life in this application comfortably greater than the life of the GIR in the telescope. A test was devised and executed to confirm the life of the runner bearing surface (track) and to characterize the bearing friction. The bearing system design and test details and results are described.

  14. Software Developed for Analyzing High- Speed Rolling-Element Bearings

    Science.gov (United States)

    Fleming, David P.

    2005-01-01

    COBRA-AHS (Computer Optimized Ball & Roller Bearing Analysis--Advanced High Speed, J.V. Poplawski & Associates, Bethlehem, PA) is used for the design and analysis of rolling element bearings operating at high speeds under complex mechanical and thermal loading. The code estimates bearing fatigue life by calculating three-dimensional subsurface stress fields developed within the bearing raceways. It provides a state-of-the-art interactive design environment for bearing engineers within a single easy-to-use design-analysis package. The code analyzes flexible or rigid shaft systems containing up to five bearings acted upon by radial, thrust, and moment loads in 5 degrees of freedom. Bearing types include high-speed ball, cylindrical roller, and tapered roller bearings. COBRA-AHS is the first major upgrade in 30 years of such commercially available bearing software. The upgrade was developed under a Small Business Innovation Research contract from the NASA Glenn Research Center, and incorporates the results of 30 years of NASA and industry bearing research and technology.

  15. Fatigue Life Analysis of Rolling Bearings Based on Quasistatic Modeling

    Directory of Open Access Journals (Sweden)

    Wei Guo

    2015-01-01

    Full Text Available Rolling bearings are widely used in aeroengine, machine tool spindles, locomotive wheelset, and so forth. Rolling bearings are usually the weakest components that influence the remaining life of the whole machine. In this paper, a fatigue life prediction method is proposed based on quasistatic modeling of rolling bearings. With consideration of radial centrifugal expansion and thermal deformations on the geometric displacement in the bearings, the Jones’ bearing model is updated, which can predict the contact angle, deformation, and load between rolling elements and bearing raceways more accurately. Based on Hertz contact theory and contact mechanics, the contact stress field between rolling elements and raceways is calculated. A coupling model of fatigue life and damage for rolling bearings is given and verified through accelerated life test. Afterwards, the variation of bearing life is investigated under different working conditions, that is, axial load, radial load, and rotational speed. The results suggested that the working condition had a great influence on fatigue life of bearing parts and the order in which the damage appears on bearing parts.

  16. Optimization analysis on assembly interference of cylindrical roller bearings

    Directory of Open Access Journals (Sweden)

    Zhen-huan Ye

    2015-07-01

    Full Text Available Distribution of loads and contact stress has a great influence on fatigue life of bearings. In view of the fact that the nonload area is ubiquitous in cylindrical roller bearings, there is a method for prolonging the fatigue life design by adjusting the working clearance of cylindrical roller bearings. In this article, optimization model of fatigue life of cylindrical roller bearings is developed with a quasi-dynamic method and calculated method of bearing life based on micro-area contact, considering the effect of assembly interference, temperature rise, and high-speed centrifugation. Aiming to the different geometry parameters and operating parameters of bearings, the effects of assembly interference on bearing fatigue life are discussed. The results show that the optimum fatigue life of roller bearings is achieved at negative working clearance with the loads distributed evenly within half ring. The optimum working clearance of roller bearings is not influenced by radial load. But with the increase in pitch diameter or decrease in rolling elements, the optimum assembly interference increases, and accelerating revolution of roller bearings will increase the optimum assembly interference as well.

  17. Socioeconomic Factors Affecting Local Support for Black Bear Recovery Strategies

    Science.gov (United States)

    Morzillo, Anita T.; Mertig, Angela G.; Hollister, Jeffrey W.; Garner, Nathan; Liu, Jianguo

    2010-06-01

    There is global interest in recovering locally extirpated carnivore species. Successful efforts to recover Louisiana black bear in Louisiana have prompted interest in recovery throughout the species’ historical range. We evaluated support for three potential black bear recovery strategies prior to public release of a black bear conservation and management plan for eastern Texas, United States. Data were collected from 1,006 residents living in proximity to potential recovery locations, particularly Big Thicket National Preserve. In addition to traditional logistic regression analysis, we used conditional probability analysis to statistically and visually evaluate probabilities of public support for potential black bear recovery strategies based on socioeconomic characteristics. Allowing black bears to repopulate the region on their own (i.e., without active reintroduction) was the recovery strategy with the greatest probability of acceptance. Recovery strategy acceptance was influenced by many socioeconomic factors. Older and long-time local residents were most likely to want to exclude black bears from the area. Concern about the problems that black bears may cause was the only variable significantly related to support or non-support across all strategies. Lack of personal knowledge about black bears was the most frequent reason for uncertainty about preferred strategy. In order to reduce local uncertainty about possible recovery strategies, we suggest that wildlife managers focus outreach efforts on providing local residents with general information about black bears, as well as information pertinent to minimizing the potential for human-black bear conflict.

  18. Foothills model forest grizzly bear study : project update

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-01-01

    This report updates a five year study launched in 1999 to ensure the continued healthy existence of grizzly bears in west-central Alberta by integrating their needs into land management decisions. The objective was to gather better information and to develop computer-based maps and models regarding grizzly bear migration, habitat use and response to human activities. The study area covers 9,700 square km in west-central Alberta where 66 to 147 grizzly bears exist. During the first 3 field seasons, researchers captured and radio collared 60 bears. Researchers at the University of Calgary used remote sensing tools and satellite images to develop grizzly bear habitat maps. Collaborators at the University of Washington used trained dogs to find bear scat which was analyzed for DNA, stress levels and reproductive hormones. Resource Selection Function models are being developed by researchers at the University of Alberta to identify bear locations and to see how habitat is influenced by vegetation cover and oil, gas, forestry and mining activities. The health of the bears is being studied by researchers at the University of Saskatchewan and the Canadian Cooperative Wildlife Health Centre. The study has already advanced the scientific knowledge of grizzly bear behaviour. Preliminary results indicate that grizzlies continue to find mates, reproduce and gain weight and establish dens. These are all good indicators of a healthy population. Most bear deaths have been related to poaching. The study will continue for another two years. 1 fig.

  19. Evaluation of a hybrid hydrostatic bearing for cryogenic turbopump application

    Science.gov (United States)

    Spica, P. W.; Hannum, N. P.; Meyer, S. D.

    1986-01-01

    A hybrid hydrostatic bearing was designed to operate in liquid hydrogen at speeds to 80,000 rpm and radial loads to 440 n (100 lbf). The bearing assembly consisted of a pair of 20-mm angular-contact ball bearings encased in a journal, which was in turn supported by a fluid film of liquid hydrogen. The size and operating conditions of the bearing were selected to be compatible with the operating requirements of an advanced technology turbopump. Several test parameters were varied to characterize the bearing's steady-state operation. The rotation of the tester shaft was varied between 0 and 80,000 rpm. Bearing inlet fluid pressure was varied between 2.07 and 4.48 MPa (300 and 650 psia), while the fluid sump pressure was independently varied between 0.34 and 2.07 MPa (50 and 300 psia). The maximum radial load applied to the bearing was 440 N (110 lbf). Measured hybrid-hydrostatic-bearing stiffness was 1.5 times greater than predicted, while the fluid flow rate through the bearing was 35 to 65 percent less than predicted. Under two-phase fluid conditions, the stiffness was even greater and the flow rate was less. The optimal pressure ratio for the bearing should be between 0.2 and 0.55 depending on the balance desired between bearing efficiency and stiffness. Startup and shutdown cyclic tests were conducted to demonstrate the ability of the hybrid-hydrostatic-bearing assembly to survive at least a 300-firing-duty cycle. For a typical cycle, the shaft was accelerated to 50,000 rpm in 1.8 sec. The bearing operated for 337 start-stop cycles without failure.

  20. Food availability and foraging near human developments by black bears

    Science.gov (United States)

    Merkle, Jerod A.; Robinson, Hugh S.; Krausman, Paul R.; Alaback, Paul B.

    2013-01-01

    Understanding the relationship between foraging ecology and the presence of human-dominated landscapes is important, particularly for American black bears (Ursus americanus), which sometimes move between wildlands and urban areas to forage. The food-related factors influencing this movement have not been explored, but can be important for understanding the benefits and costs to black bear foraging behavior and the fundamental origins of bear conflicts. We tested whether the scarcity of wildland foods or the availability of urban foods can explain when black bears forage near houses, examined the extent to which male bears use urban areas in comparison to females, and identified the most important food items influencing bear movement into urban areas. We monitored 16 collared black bears in and around Missoula, Montana, during 2009 and 2010, while quantifying the rate of change in green vegetation and the availability of 5 native berry-producing species outside the urban area, the rate of change in green vegetation, and the availability of apples and garbage inside the urban area. We used parametric time-to-event models in which an event was a bear location collected within 100 m of a house. We also visited feeding sites located near houses and quantified food items bears had eaten. The probability of a bear being located near a house was 1.6 times higher for males, and increased during apple season and the urban green-up. Fruit trees accounted for most of the forage items at urban feeding sites (49%), whereas wildland foods composed <10%. Black bears foraged on human foods near houses even when wildland foods were available, suggesting that the absence of wildland foods may not influence the probability of bears foraging near houses. Additionally, other attractants, in this case fruit trees, appear to be more important than the availability of garbage in influencing when bears forage near houses.

  1. Studies on Excess Volume, Viscosity, and Speed of Sound of Binary Mixtures of Methyl Benzoate in Ethers at T=(303.15,308.15, and 313.15 K

    Directory of Open Access Journals (Sweden)

    M. V. Rathnam

    2013-01-01

    Full Text Available Densities, viscosities, and speed of sound have been determined at T = (303.15, 308.15, and 313.15 K for the binary mixtures of methyl benzoate with tetrahydrofuran, 1,4-dioxane, anisole, and butyl vinyl ether over the entire range of composition. Using these measured values, excess volume VE, deviation in viscosities Δη, excess Gibb’s free energy of activation for viscous flow ΔG*E, and deviation in isentropic compressibility Δks have been calculated. These calculated binary data have been fitted to Redlich-Kister equation to determine the appropriate coefficients. The values of excess volume VE and deviation in viscosities Δη are negative over the entire range of composition for all the binary systems at the studied temperatures. The behavior of these parameters with composition of the mixture has been discussed in terms of molecular interactions between the components of liquids.

  2. Crystal structure of ethyl 4-[(E)-(4-hy­droxy-3-meth­oxy­benzyl­idene)amino]­benzoate: a p-hy­droxy Schiff base

    Science.gov (United States)

    Ling, Jing; Kavuru, Padmini; Wojtas, Lukasz; Chadwick, Keith

    2016-01-01

    The title p-hy­droxy Schiff base, C17H17NO4, was synthesized via the condensation reaction of benzocaine with vanillin. The benzyl­idine and benzoate rings are inclined to one another by 24.58 (8)°, and the conformation about the C=N bond is E. In the crystal, mol­ecules are linked by O—H⋯N hydrogen bonds, forming zigzag chains propagating along [010]. Adjacent chains are linked by C—H⋯π and weak offset π–π inter­actions [inter­centroid distance = 3.819 (1) Å], forming sheets parallel to (10-2). PMID:27555938

  3. Positive contact, self retaining bearing seals

    Science.gov (United States)

    Johnson, Bruce H.; Larsen, Lawrence E.; Welch, Edmund F.

    1992-05-05

    An ultra-low friction bearing including an inner race, an outer race, bearing elements engaged between the inner and outer races and a seal between the inner and outer races is disclosed. The seal includes first and second sealing washers. The first washer has an outer diameter greater than an inner diameter of the outer race and an inner diameter greater than the outer diameter of the inner race. The second washer has an inner diameter less than the outer diameter of the inner race and an outer diameter less than the inner diameter of the outer race. The first washer slidably engages the outer race, the second washer slidably engages the inner race and the washers overlap and slidably engage one another. One of the washers snap fits into its respective inner or outer race while the other washer engages a stepped surface of the other of the inner and outer races. The grooved and stepped surface are offset from one another in a longitudinal direction of the races such that the washers are conically loaded thus providing a seal between the inner and outer races sufficient to prevent lubricant and contaminating particles from passing therethrough. The washers are made from a non-metallic semi-flexible low-modulus material.

  4. Non-fuel bearing hardware melting technology

    International Nuclear Information System (INIS)

    Battelle has developed a portable hardware melter concept that would allow spent fuel rod consolidation operations at commercial nuclear power plants to provide significantly more storage space for other spent fuel assemblies in existing pool racks at lower cost. Using low pressure compaction, the non-fuel bearing hardware (NFBH) left over from the removal of spent fuel rods from the stainless steel end fittings and the Zircaloy guide tubes and grid spacers still occupies 1/3 to 2/5 of the volume of the consolidated fuel rod assemblies. Melting the non-fuel bearing hardware reduces its volume by a factor 4 from that achievable with low-pressure compaction. This paper describes: (1) the configuration and design features of Battelle's hardware melter system that permit its portability, (2) the system's throughput capacity, (3) the bases for capital and operating estimates, and (4) the status of NFBH melter demonstration to reduce technical risks for implementation of the concept. Since all NFBH handling and processing operations would be conducted at the reactor site, costs for shipping radioactive hardware to and from a stationary processing facility for volume reduction are avoided. Initial licensing, testing, and installation in the field would follow the successful pattern achieved with rod consolidation technology

  5. Triphenyltin(IV) 2-[(E)-2-(aryl)-1-diazenyl]benzoates as anticancer drugs: synthesis, structural characterization, in vitro cytotoxicity and study of its influence towards the mechanistic role of some key enzymes.

    Science.gov (United States)

    Basu Baul, Tushar S; Paul, Anup; Pellerito, Lorenzo; Scopelliti, Michelangelo; Singh, Palwinder; Verma, Pooja; de Vos, Dick

    2010-10-01

    Triphenyltin(IV) complexes of composition [Ph(3)SnL(1)H](n) (1) and [Ph(3)SnL(2)H](n) (2) (where L(1)H = 2-[(E)-2-(3-formyl-4-hydroxyphenyl)-1-diazenyl]benzoate and L(2)H = 2-[(E)-2-(4-Hydroxy-5-methylphenyl)-1-diazenyl]benzoate) were synthesized and characterized by spectroscopic ((1)H, (13)C and (119)Sn NMR, IR, (119)Sn Mössbauer) techniques in combination with elemental analysis. The molecular structures and geometries of the complexes (1 and 2) were fully optimized using the quantum mechanical method (PM3). Complexes (1 and 2) were found to exhibit stronger cytotoxic activity in vitro across a panel of human tumour cell lines viz., A498, EVSA-T, H226, IGROV, M19 MEL, MCF-7 and WIDR. The test compounds 1 and 2 exhibit comparable results and both the compounds are found to be far superior to CCDP (cisplatin), 5-FU (5-fluorouracil) and ETO (etoposide) across a panel of cell lines and the activity is more pronounced for the A498 (22 fold) and H226 (33 fold) cell lines compared to CCDP, and A498 (13 fold), H226 (39 fold) and MCF-7 (33 fold) cell lines compared to ETO. The test compounds are even 23 fold more active in magnitude in terms of the ID(50) value at least against the H226 cell lines when compared with MTX (methotrexate). Further, the mechanistic role of cytotoxic activity of test compounds (1 and 2), are discussed in relations to the theoretical results of docking studies with some of the key enzymes such as ribonucleotide reductase, thymidylate synthase, thymidylate phosphorylase and topoisomerase II. PMID:19641849

  6. Molecular basis of the interaction of novel tributyltin(IV) 2/4-[(E)-2-(aryl)-1-diazenyl]benzoates endowed with an improved cytotoxic profile: synthesis, structure, biological efficacy and QSAR studies.

    Science.gov (United States)

    Basu Baul, Tushar S; Paul, Anup; Pellerito, Lorenzo; Scopelliti, Michelangelo; Pellerito, Claudia; Singh, Palwinder; Verma, Pooja; Duthie, Andrew; de Vos, Dick; Verma, Rajeshwar P; Englert, Ulli

    2010-09-01

    A series of tributyltin(IV) complexes based on 2/4-[(E)-2-(aryl)-1-diazenyl]benzoate ligands was synthesized, wherein the position of the carboxylate and aryl substituents (methyl, tert-butyl and hydroxyl) varies. The complexes, Bu(3)SnL(1-4)H (1-4), have been structurally characterized by elemental analysis and IR, NMR ((1)H, (13)C, and (119)Sn) and (119)Sn Mössbauer spectroscopy. All have a tetrahedral geometry in solution and a trigonal bipyramidal geometry in the solid-state, except for Bu(3)SnL(4)H (4) that was ascertained to have tetrahedral coordination by X-ray crystallography. Cytotoxicity studies were carried out on human tumor cell lines A498 (renal cancer), EVSA-T (mammary cancer), H226 (non-small-cell lung cancer), IGROV (ovarian cancer), M19 MEL (melanoma), MCF-7 (mammary cancer) and WIDR (colon cancer). Compared to cisplatin, test compounds 1-4 had remarkably good activity, despite the presence of substantial steric bulk due to Sn-Bu ligands. The quantitative structure-activity relationship (QSAR) studies for the cytotoxicity of organotin(IV) benzoates, along with some reference drug molecules, is also discussed against a panel of human tumor cell lines. Molecular structures of the tributyltin(IV) complexes (1-4) were fully optimized using the PM6 semi-empirical method and docking studies performed with key enzymes associated with the propagation of cancer, namely ribonucleotide reductase, thymidylate synthase, thymidylate phosphorylase and topoisomerase II. The theoretical results are discussed in relation to the mechanistic role of the cytotoxic active test compounds (1-4). PMID:20553814

  7. Individual effects of seasonal changes, visitor density, and concurrent bear behavior on stereotypical behaviors in captive polar bears (Ursus maritimus).

    Science.gov (United States)

    Kelly, Krista R; Harrison, Michelle L; Size, Daniele D; MacDonald, Suzanne E

    2015-01-01

    Stereotypical behaviors in captive polar bears (Ursus maritimus) can be detrimental to their welfare. These behaviors can be reduced through enrichment programs but are often not completely eliminated, so identifying potential triggers is important. The present study investigated the influences of seasonal changes, visitor density, and concurrent bear activity on stereotypical behaviors exhibited by 3 captive polar bears at the Toronto Zoo. All bears exhibited these behaviors; however, individual differences were found in duration and form. The male exhibited less stereotypical behavior during spring, and the females exhibited less stereotypical behavior during winter. An increase in visitor density was associated with more stereotypical behavior in 1 female but less stereotypical behavior in the other 2 bears. All bears engaged in more stereotypical behaviors when the other bears were inactive, and 1 female engaged in more stereotypical behaviors when the other bears were out of sight. Further, when conspecifics were active, all bears engaged in less stereotypical behaviors. Given the variability among individual bears, future enrichment programs must be tailored to the needs of individuals to maximize efficacy. PMID:24933263

  8. 甲维盐胁迫对西花蓟马能源物质的影响%The Effect of Emamectin Benzoate Exposure on the Energy Source of Frankliniella occidentalis

    Institute of Scientific and Technical Information of China (English)

    曹宇; 刘燕; 杨文佳; 孟永禄; 王丽娟; 曾力; 李灿

    2015-01-01

    为研究甲氨基阿维菌素苯甲酸盐对西花蓟马的控制作用,室内采用浸叶法测定了其对西花蓟马成虫和二龄若虫的毒力。同时,测定了甲维盐LC50短时胁迫不同时间后,西花蓟马可溶性蛋白质、可溶性糖及脂肪三种能源物质含量的变化;其致死后,计算了昆虫对各能源物质的利用率,以期从生理生化角度探讨其作用机制。结果表明,甲维盐对西花蓟马成虫和若虫的LC50分别为1.11和0.62 mg/L,在其LC50短时胁迫过程中,西花蓟马成虫体内的能源物质含量均伴有显著的升高及降低,但若虫并无显著变化;其LC50致死下,西花蓟马对三种能源物质的利用率存在显著差异,成虫为可溶性糖(74.12%)>可溶性蛋白质(58.10%)>脂肪(42.13%),若虫为可溶性糖(64.01%)>可溶性蛋白质(48.12%)>脂肪(36.48%),且无论何种能源物质,西花蓟马成虫的利用率均显著高于若虫。%In order to examine the effect of emamectin benzoate to Frankliniella occidentalis, the toxicity of this insecticide to the adult and 2nd instar of F.occidentalis were studied by dip method in this paper. In addition, the content of soluble protein, soluble sugar and lipid in F.occidentalis were also tested after these insects were exposed to medial lethal doses of emamectin benzoate for the following exposure times:2, 4, 6, and 8 h.Furthermore the utilization rate of the energy source in F.occidentalis was calculated after the insects were exposed to emamectin benzoate until dead at the medial lethal doses.The results showed that emamectin benzoate had different toxicity to the adult and 2nd instar of F.occidentalis, and the medial lethal doses were 1.11 and 0.62 mg/L, respectively.With the extension of exposure time at medial lethal doses of emamectin benzoate, there was significant a increase or decrease on the content of soluble protein, soluble

  9. The R and D D's bearing test benches

    International Nuclear Information System (INIS)

    In power generation plants, rotating machines are involved in energy transformation processes and safety systems. The bearings supporting the rotors and the thrust bearings play a crucial role in the reliability of these machines. The phenomena encountered straddle several disciplines: hydrodynamics, tribology, thermomechanics, materials and vibrations in a specific environment, namely: thin fluid film, solid mechanical components and shaft rotation. Means of analysing the behaviour of these components (bearings and thrust bearings) have been developed and implemented. These consists of the EDYOS (Etude Dynamique des Organes de Supportage) code for dynamically studying bearing devices and several related bench tests. In reality, in order to understand the complex physical phenomena encountered in these components, it is vital to carry out analyses and experimental validations. Since these investigations cannot be carried out on actual machines, test benches have been built which can subject the sample bearings to the equivalent stresses. (author)

  10. A Review on Prognosis of Rolling Element Bearings

    Directory of Open Access Journals (Sweden)

    N.S. Jammu

    2011-10-01

    Full Text Available Bearings are amongst the frequently encountered components to be found in rotating machinery. Though inexpensive, their failure can interrupt the production in a plant causing unscheduled downtime and production losses. So the bearing prognosis plays a significant role in reducing plant down time and enhanced operation safety, by estimating the Remaining Useful Life (RUL of damaged bearing. Admitting the importance of bearing prognosis, this literature reviewattempts to summarize various techniques, methods and models used in the prognosis of bearing till date. The definition of bearing prognosis is discussed in the beginning, followed by classification ofvarious prognostic methods, review of methods used by various investigators in this research domain and concluding the topic with the summary of future research directions.

  11. Wear fault diagnosis of an emulsion pump crank bearing

    Institute of Scientific and Technical Information of China (English)

    HAN Xiao-ming; DU Chang-long; ZHANG Yong-zhong; TIE Zhan-xu

    2008-01-01

    The total load on a crank bearing was calculated by performing a load analysis of the crank connecting rod mechanism.The Reynolds equation for hydrodynamic lubrication of the crank bearing was established at the Reynolds boundary condition and was then solved using the Holland method. From this the regular track of the bearing axis was obtained. As the crank bearing gradually wears the eccentricity ratio corresponding to the minimum oil film thickness increases gradually. The oil-bound film eventually breaks down, which allows friction and collision between the metal surfaces of the crank pin and the bearing. The rigid impact leads to excitation of high frequency vibrations at the natural frequencies of the connecting rod. The experiments show that the wear condition of the crank bearing can be identified correctly through the vibration signature at the natural frequencies of the connecting rod. The degree of wear can be predicted accurately through the energy content of the high frequency bands.

  12. Compliant Foil Journal Bearings - Investigation of Dynamic Properties

    DEFF Research Database (Denmark)

    Larsen, Jon Steffen; Santos, Ilmar

    Through the past three decades gas bearings have found way into an increasing number of industrial applications within high speed rotating machinery. Especially the compliant foil type of bearings has gained large popularity. Much theoretical and experimental work has been conducted...... on the compliant foil bearings, and the understanding of their dynamic behaviour is growing. However, practical design involving these bearings are still associated with a large degree of trial and error. This study aims at establishing an accurate mathematical model, to calculate the pressure, film height...... and dynamic coefficients, of the compliant foil bearing together with an efficient solution method, which can be easily adopted and implemented by mechanical engineers. A theoretical model of a radial compliant foil bearing that incorporates compressibility of the lubricating gas and flexibility...

  13. Detection of bearing damage by statistic vibration analysis

    Science.gov (United States)

    Sikora, E. A.

    2016-04-01

    The condition of bearings, which are essential components in mechanisms, is crucial to safety. The analysis of the bearing vibration signal, which is always contaminated by certain types of noise, is a very important standard for mechanical condition diagnosis of the bearing and mechanical failure phenomenon. In this paper the method of rolling bearing fault detection by statistical analysis of vibration is proposed to filter out Gaussian noise contained in a raw vibration signal. The results of experiments show that the vibration signal can be significantly enhanced by application of the proposed method. Besides, the proposed method is used to analyse real acoustic signals of a bearing with inner race and outer race faults, respectively. The values of attributes are determined according to the degree of the fault. The results confirm that the periods between the transients, which represent bearing fault characteristics, can be successfully detected.

  14. Enhancing stability of industrial turbines using adjustable partial arc bearings

    Science.gov (United States)

    Chasalevris, Athanasios; Dohnal, Fadi

    2016-09-01

    The paper presents the principal of operation, the simulation and the characteristics of two partial-arc journal bearings of variable geometry and adjustable/controllable stiffness and damping properties. The proposed journals are supposed to consist of a scheme that enables the periodical variation of bearing properties. Recent achievements of suppressing rotor vibrations using plain circular journal bearings of variable geometry motivate the further extension of the principle to bearings of applicable geometry for industrial turbines. The paper describes the application of a partial-arc journal bearing to enhance stability of high speed industrial turbines. The proposed partial-arc bearings with adjustable/controllable properties enhance stability and they introduce stable margins in speeds much higher than the 1st critical.

  15. Improvement of design technique of track machines bodies bearing structures

    Directory of Open Access Journals (Sweden)

    Bogdan TOVT

    2012-01-01

    Full Text Available The paper is devoted to improvement of design technique of track machines bodies bearing structures. The review and analysis of state-of-the-art of the mathematical programming theory and the optimal designing are done. The numerical optimization procedure for track machines bodies bearing structures is proposed. The approbation of the proposed procedure is taken on structural optimization problems. Mathematical aspects of proposed procedure implementation are investigated, particularly the algorithm convergence and the sensitivity analysis of initial designs.Deflected mode of the ballast leveling machine SPZ-5/UA body bearing structure was investigated analytically (FEM study and experimentally (trial running inspection on durability. The necessity of optimization implementation for bodies bearing structures is substantiated. The rational design of track machine SPZ-5/UA bearing structure was obtained with the numerical optimization procedure proposed in the paper. The deflected mode of the body rational bearing structure was investigated.

  16. Suppression of Base Excitation of Rotors on Magnetic Bearings

    OpenAIRE

    Steven Marx; C. Nataraj

    2007-01-01

    This paper deals with rotor systems that suffer harmonic base excitation when supported on magnetic bearings. Magnetic bearings using conventional control techniques perform poorly in such situations mainly due to their highly nonlinear characteristics. The compensation method presented here is a novel optimal control procedure with a combination of conventional, proportional, and differential feedback control. A four-degree-of-freedom model is used for the rotor system, and the bearings are ...

  17. Variable viscosity condition in the modeling of a slider bearing

    OpenAIRE

    Uprety, Kedar Nath; Mancas, Stefan C.

    2014-01-01

    To reduce tear and wear of machinery lubrication is essential. Lubricants form a layer between two surfaces preventing direct contact and reduce friction between moving parts and hence reduce wear. In this short letter the lubrication of two slider bearings with parallel and nonparallel is studied. First, we show that bearings with parallel plates cannot support any load. For bearings with nonparallel plates we are interested on how constant and temperature dependent viscosity affects the pro...

  18. Interaction of Reinforced Elastomeric Bearings in Bridge Construction

    OpenAIRE

    Nittmannová Ľubica; Magura Martin

    2016-01-01

    The aim of this paper is to demonstrate the behavior of reinforced elastomeric bearings under various loads. They are made of special types of bearings. The experimental verification of these special bearings has been tested on various types of loading. The results of the experimental measurements are compared with the results of the numerical modeling and calculations according to the standard assumptions in STN EN 1337-3. In the conclusion, the results are summarized for the selected types ...

  19. MOBILE TIBIAL POLYETHYLENE BEARING IN TOTAL KNEE ARTHROPLASTY

    OpenAIRE

    de Araújo Barros Cobra, Hugo Alexandre; da Palma, Idemar Monteiro

    2015-01-01

    Debris of polyethylene tibial bearings have been recognized as a major cause for the onset of the cascade of biological events leading to osteolysis and loosening of prosthetic components after total knee arthroplasty. Since then, research has been focused on alternative bearing surfaces in order to minimize the amount and rate of polyethylene wear off and, in doing so, increasing the survivorship rate for knee arthroplasties. One such option is to have a mobile tibial bearing allowing more c...

  20. Household Portfolios and Risk Bearing over Age and Time

    OpenAIRE

    Alessandro Bucciol; Raffaele Miniaci

    2011-01-01

    We exploit the US Survey of Consumer Finances from 1998 to 2007 to study households’ portfolio risk bearing. We compare four alternative measures of risk, two based on a financial portfolio and two based on a broader portfolio also including – as illiquid assets – human capital, real estate, business wealth and related debt. The measures provide a different ranking of household risk bearing, but they consistently show that risk bearing fell after 2001, and it positively correlates with wealth...