WorldWideScience

Sample records for bearing development program

  1. Bearing development program for a 25 kWe solar-powered organic Rankine-cycle engine

    Science.gov (United States)

    Nesmith, B.

    1985-01-01

    The bearing development program is summarized for a 25-kWe power conversion subsystem (PCS) consisting of an organic Rankine-cycle engine, and permanent magnetic alternator (PMA) and rectifier to be used in a 100-kWe point-focusing distributed receiver solar power plant. The engine and alternator were hermetically sealed and used toluene as the working fluid. The turbine, alternator, and feed pump (TAP) were mounted on a single shaft operating at speeds up to 60,000 rev/min. Net thermal-to-electric efficiencies in the range of 21 to 23% were demonstrated at the maximum working fluid temperature of 400 C (750 F). A chronological summary of the bearing development program is presented. The primary causes of bearing wear problems were traced to a combination of rotordynamic instability and electrodynamic discharge across the bearing surfaces caused by recirculating currents from the PMA. These problems were resolved by implementing an externally supplied, flooded-bearing lubrication system and by electrically insulating all bearings from the TAP housing. This program resulted in the successful development of a stable, high-speed, toluene-lubricated five-pad tilting-pad journal bearing and Rayleigh step thrust bearing system capable of operating at all inclinations between horizontal and vertical.

  2. Soils, surficial geology, and geomorphology of the Bear Creek Valley Low-Level Waste Disposal Development and Demonstration Program site

    International Nuclear Information System (INIS)

    Lietzke, D.A.; Lee, S.Y.; Lambert, R.E.

    1988-04-01

    An intensive soil survey was conducted on the proposed Low-Level Waste Disposal Development and Demonstration Program site (LLWDDD) in Bear Creek Valley. Soils on the site were related to the underlying residuum and to the surficial colluvium and alluvium. Within any particular geologic formation, soils were subdivided based mostly on the degree of weathering, as reflected by saprolite weathering and morphologic features of the soils. Degree of weathering was related both to slope shape and gradient and to the joint-fracture system. Erosion classes were also used to make further subdivisions of any particular soil. Deep pits were dug in each of the major Conasauga Group formations (Pumpkin Valley, Rogersville, Maryville, and Nolichucky) for soil and saprolite characterization. Because of the widespread presence of alluvium and colluvium, which are potential sources of fill and final cover material, pits and trenches were dug to characterize the properties of these soils and to try to understand the past geomorphic history of the site. The results of the soil survey investigation indicated that the deeply weathered Pumpkin Valley residuum has good potential for the construction of tumuli or other types of belowground or aboveground burial of prepackaged compacted waste. 11 refs., 30 figs., 3 tabs

  3. Technology development for indigenous water lubricated bearings

    International Nuclear Information System (INIS)

    Limaye, P.K.; Soni, N.L.; Agrawal, R.G.

    2010-01-01

    Water Lubricated Bearings (WLB) are used in various mechanisms of fuel handling systems of PHWRs and AHWR. Availability and random failures of these bearings was a major factor in refuelling operations. Indigenous development of these bearings was taken up and 7 types of antifriction bearings in various sizes (totaling 37 variants) for PHWR, AHWR and Dhruva applications were successfully developed. This paper deals with various aspects of WLB development. (author)

  4. 77 FR 70423 - Black Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC...

    Science.gov (United States)

    2012-11-26

    ... Bear Hydro Partners, LLC and Black Bear Development Holdings, LLC and Black Bear SO, LLC; Notice of..., 2012, Black Bear Hydro Partners, LLC, sole licensee (transferor) and Black Bear Development Holdings, LLC and Black Bear SO, LLC (transferees) filed an application for the partial the transfer of licenses...

  5. Technical Development Path for Gas Foil Bearings

    Science.gov (United States)

    Dellacorte, Christopher

    2016-01-01

    Foil gas bearings are in widespread commercial use in air cycle machines, turbocompressors and microturbine generators and are emerging in more challenging applications such as turbochargers, auxiliary power units and propulsion gas turbines. Though not well known, foil bearing technology is well over fifty years old. Recent technological developments indicate that their full potential has yet to be realized. This paper investigates the key technological developments that have characterized foil bearing advances. It is expected that a better understanding of foil gas bearing development path will aid in future development and progress towards more advanced applications.

  6. River-Based Experiential Learning: the Bear River Fellows Program

    Science.gov (United States)

    Rosenberg, D. E.; Shirley, B.; Roark, M. F.

    2012-12-01

    The Department of Civil and Environmental Engineering, Outdoor Recreation, and Parks and Recreation programs at Utah State University (USU) have partnered to offer a new, unique river-based experiential learning opportunity for undergraduates called the Bear River Fellows Program. The program allows incoming freshmen Fellows to experience a river first hand during a 5-day/4-night river trip on the nearby Bear River two weeks before the start of their first Fall semester. As part of the program, Fellows will navigate the Bear River in canoes, camp along the banks, interact with local water and environmental managers, collect channel cross section, stream flow, vegetation cover, and topological complexity data, meet other incoming freshmen, interact with faculty and graduate students, develop boating and leadership skills, problem solve, and participate as full members of the trip team. Subsequently, Fellows will get paid as undergraduate researchers during their Fall and Spring Freshman semesters to analyze, synthesize, and present the field data they collect. The program is a collaborative effort between two USU academic units and the (non-academic) division of Student Services and supports a larger National Science Foundation funded environmental modelling and management project for the lower Bear River, Utah watershed. We have advertised the program via Facebook and emails to incoming USU freshmen, received 35 applications (60% women), and accepted 5 Fellows into the program (3 female and 2 male). The river trip departs August 14, 2012. The poster will overview the Bear River Fellows Program and present qualitative and preliminary outcomes emerging from the trip and Fellows' work through the Fall semester with the field data they collect. We will also undertake more rigorous and longer longitudinal quantitative evaluation of Program outcomes (for example, in problem-solving and leadership) both in Spring 2013 and in subsequent 2013 and 2014 offerings of the

  7. Development and Evaluation of Titanium Spacesuit Bearings

    Science.gov (United States)

    Rhodes, Richard; Battisti, Brian; Ytuarte, Raymond, Jr.; Schultz, Bradley

    2016-01-01

    The Z-2 Prototype Planetary Extravehicular Space Suit Assembly is a continuation of NASA's Z-series of spacesuits, designed with the intent of meeting a wide variety of exploration mission objectives, including human exploration of the Martian surface. Incorporating titanium bearings into the Z-series space suit architecture allows us to reduce mass by an estimated 23 lbs per suit system compared to the previously used stainless steel bearing race designs, without compromising suit functionality. There are two obstacles to overcome when using titanium for a bearing race- 1) titanium is flammable when exposed to the oxygen wetted environment inside the space suit and 2) titanium's poor wear properties are often challenging to overcome in tribology applications. In order to evaluate the ignitability of a titanium space suit bearing, a series of tests were conducted at White Sands Test Facility (WSTF) that introduced the bearings to an extreme test profile, with multiple failures imbedded into the test bearings. The testing showed no signs of ignition in the most extreme test cases; however, substantial wear of the bearing races was observed. In order to design a bearing that can last an entire exploration mission (approx. 3 years), design parameters for maximum contact stress need to be identified. To identify these design parameters, bearing test rigs were developed that allow for the quick evaluation of various bearing ball loads, ball diameters, lubricants, and surface treatments. This test data will allow designers to minimize the titanium bearing mass for a specific material and lubricant combination and design around a cycle life requirement for an exploration mission. This paper reviews the current research and testing that has been performed on titanium bearing races to evaluate the use of such materials in an enriched oxygen environment and to optimize the bearing assembly mass and tribological properties to accommodate for the high bearing cycle life for an

  8. Development of AE monitoring system for journal bearing

    International Nuclear Information System (INIS)

    Yoon, Dong Jin; Kwon, Oh Yang; Chung, Min Hwa

    1994-01-01

    For the purpose of monitoring of the bearing conditions in rotating machinery, a system for journal bearing diagnosis by AE was developed. Acoustic emission technique is used to detect abnormal conditions in the bearing system. And various data such as AE events, rms voltage level of AE signals, and AE parameters were acquired during experiments with the simulated journal bearing system. Based on the above results and practical application for power plant, algorithms and judgement criteria for diagnosis system was accomplished. Bearing diagnosis system is composed of four parts as follows : sensing part for AE sensor and preamplifier, signal processing part for rms-to-dc converting to measure AE rms voltage, interface part for connecting rms signal to PC using A/D converter, graphic display and software part for display of bearing condition and for managing of diagnosis program.

  9. Effect of partial weight bearing program on functional ability and ...

    African Journals Online (AJOL)

    Lilian A. Zaky

    2013-03-17

    Mar 17, 2013 ... essence of the importance of partial weight bearing program in rehabilitation of lower limb condi ... and long term physical and psychosocial impairments [11,12]. .... gram for their functional walking using the 6-min walking test,.

  10. Development of Motor Bearings for a New SADA (BepiColombo)

    Science.gov (United States)

    Kreuser, J.; Bachman, R.; Bergrath, B.; Heinrich, B.; Zemann, J.

    2013-09-01

    The special requirements of the new MPO Solar Array Drive Assembly (SADA) developed for the BepiColombo program demanded also new ball bearing designs. In addition to typical requirements for other bearings in space mechanisms, the BepiColombo mission is characterized by a non-operating time of six years at extreme environmental conditions. In cooperation with RUAG Space CEROBEAR has developed different types of ball bearings for this SADA including motor bearings for the drive, a customized stepper motor.The purpose of this paper is to present and summarize the results of the development of the motor bearings of the SADA.

  11. Applied CATIA Secondary Development to Parametric Design of Active Magnetic Bearing

    Directory of Open Access Journals (Sweden)

    Zhang Li

    2016-01-01

    Full Text Available Based on the properties of active magnetic bearing, the electromagnetic parameters and structure parameters are analyzed, parametric design method is introduced to study the structure of active magnetic bearing. Through a program personalization process that is in accordance with active magnetic bearing is established. Personalization process aims to build the parametric model of active magnetic bearings and component library by use of CATIA secondary development. Component library is to build assembly model for a multiple degree of freedom magnetic bearing system. Parametric design is a method that provides the direction for its structural design.

  12. Acoustic Emission Monitoring of Incipient Failure in Journal Bearings( III ) - Development of AE Diagnosis System for Journal Bearings -

    International Nuclear Information System (INIS)

    Chung, Min Hwa; Cho, Yong Sang; Yoon, Dong Jin; Kwon, Oh Yang

    1996-01-01

    For the condition monitoring of the journal bearing in rotating machinery, a system for their diagnosis by acoustic emission(AE) was developed. AE has been used to detect abnormal conditions in the bearing system. It was found from the field application study as well as the laboratory experiment using a simulated journal bearing system that AE RMS voltage was the most efficient parameter for the purpose of current study. Based on the above results, algorithms and judgement criteria for the diagnosis system was established. The system is composed of four parts as follows: the sensing part including AE sensor and preamplifier, the signal processing part for RMS-to-DC conversion to measure AE ms voltage, the interface part for transferring RMS voltage data into PC using A/D converter, and the software part including the graphic display of bearing conditions and the diagnosis program

  13. Senior Program Specialist | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... offices on issues of program and project development and management;; Plays ... Ensures that a regional perspective is brought to bear on program planning at the ... between Canadian and developing country researchers;; When traveling, ...

  14. Development of an Anti-Vibration Controller for Magnetic Bearing Cooling Systems, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This proposal outlines a program to develop a vibration-free reverse-Brayton cycle cooling system using specially-tuned magnetic bearings. Such a system is critical...

  15. The Development of Open Water-lubricated Polycrystalline Diamond (PCD) Thrust Bearings for Use in Marine Hydrokinetic (MHK) Energy Machines

    Energy Technology Data Exchange (ETDEWEB)

    Cooley, Craig, H.; Khonsari, Michael,, M; Lingwall, Brent

    2012-11-28

    Polycrstalline diamond (PCD) bearings were designed, fabricated and tested for marine-hydro-kinetic (MHK) application. Bearing efficiency and life were evaluated using the US Synthetic bearing test facility. Three iterations of design, build and test were conducted to arrive at the best bearing design. In addition life testing that simulated the starting and stopping and the loading of real MHK applications were performed. Results showed polycrystalline diamond bearings are well suited for MHK applications and that diamond bearing technology is TRL4 ready. Based on life tests results bearing life is estimated to be at least 11.5 years. A calculation method for evaluating the performance of diamond bearings of round geometry was also investigated and developed. Finally, as part of this effort test bearings were supplied free of charge to the University of Alaska for further evaluation. The University of Alaska test program will subject the diamond bearings to sediment laden lubricating fluid.

  16. The development of cobalt-base alloy ball bearing

    International Nuclear Information System (INIS)

    Yu Xinshui; Chen Jianting; Wang Zaishu; Wang Ximei; Huang Chongming.

    1986-01-01

    The main technologies and experiences in developing a Cobalt-base alloy ball bearing are described. In the hardfacing of bearing races, a lower-hardness alloy of type St-6 is used rather than an alloy with hardness similar to that of the ball and finally the hardness of race is increased to match that of the ball by heat treatment. This improvement has certain advantages. The experience of whole developing technology indicates that strict control of the technology in the bearing-race hardfacing is the key problem in the quality assurance of bearings

  17. Progress in development of high capacity magnetic HTS bearings

    International Nuclear Information System (INIS)

    Kummeth, P.; Nick, W.; Neumueller, H.-W.

    2005-01-01

    HTS magnetic bearings are inherently stable without an active feedback system. They provide low frictional losses, no wear and allow operation at high rotational speed without lubrication. So they are very promising for use in motors, generators and turbines. We designed and constructed an HTS radial bearing for use with a 400 kW HTS motor. It consists of alternating axially magnetized permanent magnet rings on the rotor and a segmented YBCO stator. Stator cooling is performed by liquid nitrogen, the temperature of the stator can be adjusted by varying the pressure in the cryogenic vessel. At 68 K maximum radial forces of more than 3.7 kN were found. These results range within the highest radial bearing capacities reported worldwide. The encouraging results lead us to develop a large heavy load HTS radial bearing. Currently a high magnetic gradient HTS bearing for a 4 MVA synchronous HTS generator is under construction

  18. Development of melt compositions for sulphate bearing high level waste

    International Nuclear Information System (INIS)

    Jahagirdar, P.B.; Wattal, P.K.

    1997-09-01

    The report deals with the development and characterization of vitreous matrices for sulphate bearing high level waste. Studies were conducted in sodium borosilicate and lead borosilicate systems with the introduction of CaO, BaO, MgO etc. Lead borosilicate system was found to be compatible with sulphate bearing high level wastes. Detailed product evaluation carried on selected formulations is also described. (author)

  19. Program Leader | IDRC - International Development Research Centre

    International Development Research Centre (IDRC) Digital Library (Canada)

    Leads in the identification of the overall development research ... Ensures that a regional perspective is brought to bear on program planning at the PI and ... The incumbent is the manager of the Program Initiative program and team and as such: ... projects between Canadian and developing country researchers; and; When ...

  20. R+D works for the further development of high temperature reactors. (1) Captive bearing experiments for active magnetic bearings. (2) Captive bearing test for HTR blowers

    International Nuclear Information System (INIS)

    1991-01-01

    When using active magnetic bearings as blower shaft bearings, blower motors and bearings must be protected against mechanical damage in case of faults (example: total electrical supply failure due to the supply cables breaking). So-called captive bearings are provided, in order to be able to shut the blowers down safely in such faults. These captive bearings are roller bearings which are additionally fitted in the area of the blower shaft bearings, to prevent mechanical contact between the blower rotor and stator. As there was little experience available for the given boundary conditions, such as - speed, - acceleration, - bearing load, - bearing dimensions, - ambient conditions, appropriate development and tests had to be carried out. It was important to determine suitable captive bearings and the necessary ambient conditions, which will make it possible to support the failures of the magnetic bearings to be expected in 40 years' operation of the reactor without damage and to meet the requirements of the captive bearings. (orig./GL) [de

  1. The BEAR program NRL plasma physics instrumentation measurements

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D.N.; Baumback, M.M.; Haas, D.G.; Rodriguez, P.; Siefring, C.L.; Doggett, R.A. [Naval Research Lab., Washington, DC (United States)

    1989-11-15

    The BEAR program was a joint effort to launch, and demonstrate the feasibility of operating, a 1 MeV 10 ma Neutral Particle Beam (NPB) accelerator from a space platform. The accelerator design and manufacture were the responsibility of Los Alamos National Lab (LANL); diagnostics associated with accelerator operation and beam-plasma effects were also to be undertaken by LANL and NRL. Payload Integration and Telemetry was provided by the Air Force Geophysical Lab (AFGL) and Northeastern University (NEU). Beam effects on the local plasma in addition to accelerator produced vehicle effects (e.g., charging) were the responsibility of NRL as outlined herein. The BEAR rocket was launched successfully during the early morning hours of July 13 from White Sands Missile Range, White Sands, N.M. The NRL contribution to this effort included three instrument packages designed to diagnose beam-plasma and vehicle-plasma interactions. The instruments included: (1) Langmuir probe (LP) design consisting of 4 separate sensors; (2) High voltage (HIV) Langmuir Probe designed to monitor vehicle charging through current polarity changes; and (3) Plasma Wave Receive (PWR) designed to characterize the plasma wave emissions covering a broad frequency range from near DC to 50 MHz.

  2. Colleges and Universities with Degree or Certificate Bearing Programs in Creativity

    Science.gov (United States)

    Yudess, Jo

    2010-01-01

    In this article, the author presents a list of colleges and universities with degree or certificate bearing programs in creativity. Since this focuses only on degree bearing programs, an individual might also focus on creativity by working with a specific faculty member in a more general program such as industrial-organizational psychology or…

  3. Superconducting magnetic bearings for machine tools. Phase 1, SBIR program. Final report

    International Nuclear Information System (INIS)

    Anastas, G.; Bennett, A.; Downer, J.; Hockney, R.

    1988-01-01

    The research was directed toward investigating the role of superconducting materials in a magnetic bearing system. Superconducting magnetic bearings are shown to offer the potential for vastly improved performance. These bearings are expected to be especially applicable to rotors which have extremely tight position tolerances. The development of superconducting magnetic bearing technology is also expected to allow a number of novel approaches in the development of machinery and systems. Researchers studied an alternative bearing design which employs a superconducting coil and eliminates all conventional magnetic structures. The study has resulted in a design definition and detailed analysis for a superconducting bearing system which is sized to roughly duplicate the air bearing system of an existing air-bearing spindle

  4. Improvement of Railroad Roller Bearing Test Procedures & Development of Roller Bearing Diagnostic Techniques. Volume 2.

    Science.gov (United States)

    1982-04-01

    A comprehensive review of existing basic diagnostic techniques applicable to the railcar roller bearing defect and failure problem was made. Of the potentially feasible diagnostic techniques identified, high frequency vibration was selected for exper...

  5. Integrated smart bearings for next generation aero-engines Part 1: Development of a sensor suite for automatic bearing health monitoring

    OpenAIRE

    Bashir, Imran; Wang, Ling; Harvey, Terence; Zaghari, Bahareh; Weddell, Alexander; White, Neil

    2017-01-01

    The development of smart bearing solutions will contribute to increased aircraft engine reliability, allowing the early detection of bearing failure through robust health monitoring. This project aims to develop intelligent bearing systems for an Ultra High Propulsion Efficiency (UHPE) ground test demonstrator, where a fully integrated self-powered wireless sensing system will be developed for future aircraft. This paper provides a comprehensive review of the state-of-the-art smart bearing te...

  6. Development of a dc motor with virtually zero powered magnetic bearing

    Science.gov (United States)

    1971-01-01

    The development of magnetic bearings for use in direct current electric motors is discussed. The characteristics of the magnets used in the construction of the bearings are described. A magnetic bearing using steel armoring on permanent magnets was selected for performance tests. The specifications of the motor are presented. The test equipment used in the evaluation is described.

  7. Carbon-Phenolic Cages for High-Speed Bearings. Part III - Development of Numerical Models for Heat Generation and Temperature Prediction in Lightly Lubricated Bearings

    National Research Council Canada - National Science Library

    Brown, Jeffrey

    2003-01-01

    .... This portion describes the bearing and thermal analysis models. A process has been developed to numerically investigate operating temperatures of a rolling element bearing which combines capabilities of the Advanced Dynamics of Rolling Elements (ADORE...

  8. Recent research and development of bearings for helium circulator

    International Nuclear Information System (INIS)

    Taniguchi, S.; Ezaki, Z.; Kawaguchi, K.; Matsumura, N.; Kozima, M.

    1988-01-01

    This paper mainly describes recent studies and successful applications of water lubricated bearing and gas lubricated bearing. Both types of bearing seem to be suitable for a turbo machine installed in an atomic energy plant - such as the helium circulator of a HTGR - not to be affected by radioactivity, so we have been attracted by them for about 10 years. The former was investigated theoretically taking account of turbulent flow due to the low viscosity of water, and compared with the experimental data. Good agreement was obtained, and a successful example applied to a small-sized high speed air compressor is shown. The latter was investigated using a large-sized bearing test rig simulated to an actual machine. The tilting pad journal bearing and the tilting pad thrust bearing were taken and improved for some aspects. These bearings have been taken into service on an actual circulator and are now operating successfully. Currently, a magnetic bearing is being studied to pay special attention to endurance for an earthquake and catcher bearing system. We would like to have an opportunity to present these results in the near future. (author). 5 refs, 15 figs, 2 tabs

  9. Food availability and foraging near human developments by black bears

    Science.gov (United States)

    Merkle, Jerod A.; Robinson, Hugh S.; Krausman, Paul R.; Alaback, Paul B.

    2013-01-01

    Understanding the relationship between foraging ecology and the presence of human-dominated landscapes is important, particularly for American black bears (Ursus americanus), which sometimes move between wildlands and urban areas to forage. The food-related factors influencing this movement have not been explored, but can be important for understanding the benefits and costs to black bear foraging behavior and the fundamental origins of bear conflicts. We tested whether the scarcity of wildland foods or the availability of urban foods can explain when black bears forage near houses, examined the extent to which male bears use urban areas in comparison to females, and identified the most important food items influencing bear movement into urban areas. We monitored 16 collared black bears in and around Missoula, Montana, during 2009 and 2010, while quantifying the rate of change in green vegetation and the availability of 5 native berry-producing species outside the urban area, the rate of change in green vegetation, and the availability of apples and garbage inside the urban area. We used parametric time-to-event models in which an event was a bear location collected within 100 m of a house. We also visited feeding sites located near houses and quantified food items bears had eaten. The probability of a bear being located near a house was 1.6 times higher for males, and increased during apple season and the urban green-up. Fruit trees accounted for most of the forage items at urban feeding sites (49%), whereas wildland foods composed fruit trees, appear to be more important than the availability of garbage in influencing when bears forage near houses.

  10. Oil and gas planning and development in Alberta : new approaches to integrate grizzly bear conservation

    Energy Technology Data Exchange (ETDEWEB)

    Stenhouse, G. [Foothills Model Forest Grizzly Bear Research Program, AB (Canada)

    2007-07-01

    This paper reported on a grizzly bear research program that was initiated in the province of Alberta to provide new knowledge and tools to ensure the long term survival of grizzly bears on a multiple use landscape. The Foothills Model Forest (FMF) Grizzly Bear Research Program was formed by scientists from across Canada from a variety of scientific disciplines. A strong partner base has been created to allow the FMF's research efforts to span the entire current distribution of grizzly bear habitat in Alberta. The FMF has provided new large scale seamless maps of grizzly bear habitat and, using detailed grizzly bear GPS movement data, has constructed and tested models that can identify key grizzly bear habitat. This presentation focused on the results of 9 years of applied research and described the new tools and models that are now available to program partners in Alberta. The products are currently being used by both industry and government in Alberta as new standards in landscape management planning in grizzly bear habitat. The author suggested that the approach taken with grizzly bears in Alberta could be used and adapted for a variety of wildlife species in the north. figs.

  11. Process control program development

    International Nuclear Information System (INIS)

    Dameron, H.J.

    1985-01-01

    This paper details the development and implementation of a ''Process Control Program'' at Duke Power's three nuclear stations - Oconee, McGuire, and Catawba. Each station is required by Technical Specification to have a ''Process Control Program'' (PCP) to control all dewatering and/or solidification activities for radioactive wastes

  12. Evaluating a Development Program.

    Science.gov (United States)

    Frantzreb, Arthur C.

    Problems in evaluating the success of an institutional resource development program are examined and suggestions are offered for effective assessment. Such a program is seen as a sequence of events in the artful management of people, from the planning stage to obtaining a financial commitment in writing from persons who want to share their assets…

  13. Purex canyon exhaust fan bearing temperature monitoring system doric 245 datalogger programming

    International Nuclear Information System (INIS)

    Blackaby, W.B.

    1994-01-01

    A micro-processor based datalogger is used to monitor, display, and log seventeen RTD temperature channels. Five bearings are monitored for each of the three electric motor-fan assemblies and two bearings are monitored on the steam turbine unit. Several alarms per data channel (a High alarm at 236 degrees and a High High alarm at 246 degrees F) will alert the operation's staff to increasing abnormal bearing temperatures. This procedure is cross-referenced to the manufacturers manual. All programming steps will have the following footnote: Mpg x-xx. The Mpg refers to the Manual page, with x as the section number and xx as the page number in that section. When more information is needed, such as pictures or details, then the manual section and page number is provided

  14. LFR Development: Italian Program

    International Nuclear Information System (INIS)

    Tarantino, M.

    2011-01-01

    Conclusions: ⇨ ENEA has one of the most relevant EU R&D infrastructures for HLM technological development; ⇨ ENEA is strongly involved in the EU R&D programs supporting the development of sub-critical (ADS) and critical lead cooled reactors (LFR - Gen. IV); ⇨ Large experimental program ranging from HLM thermalhydraulic to large scale experiment has been implemented in Italy, partially funded by the National Program; ⇨ Large competencies are available related to Safety Assessment, System Design, Core Design & Optimization; ⇨ ENEA is able to cooperate with other laboratories in order to promote the growth and diffusion of the technology for nuclear application

  15. Development of a morphological convolution operator for bearing fault detection

    Science.gov (United States)

    Li, Yifan; Liang, Xihui; Liu, Weiwei; Wang, Yan

    2018-05-01

    This paper presents a novel signal processing scheme, namely morphological convolution operator (MCO) lifted morphological undecimated wavelet (MUDW), for rolling element bearing fault detection. In this scheme, a MCO is first designed to fully utilize the advantage of the closing & opening gradient operator and the closing-opening & opening-closing gradient operator for feature extraction as well as the merit of excellent denoising characteristics of the convolution operator. The MCO is then introduced into MUDW for the purpose of improving the fault detection ability of the reported MUDWs. Experimental vibration signals collected from a train wheelset test rig and the bearing data center of Case Western Reserve University are employed to evaluate the effectiveness of the proposed MCO lifted MUDW on fault detection of rolling element bearings. The results show that the proposed approach has a superior performance in extracting fault features of defective rolling element bearings. In addition, comparisons are performed between two reported MUDWs and the proposed MCO lifted MUDW. The MCO lifted MUDW outperforms both of them in detection of outer race faults and inner race faults of rolling element bearings.

  16. Automatic Program Development

    DEFF Research Database (Denmark)

    Automatic Program Development is a tribute to Robert Paige (1947-1999), our accomplished and respected colleague, and moreover our good friend, whose untimely passing was a loss to our academic and research community. We have collected the revised, updated versions of the papers published in his...... honor in the Higher-Order and Symbolic Computation Journal in the years 2003 and 2005. Among them there are two papers by Bob: (i) a retrospective view of his research lines, and (ii) a proposal for future studies in the area of the automatic program derivation. The book also includes some papers...... by members of the IFIP Working Group 2.1 of which Bob was an active member. All papers are related to some of the research interests of Bob and, in particular, to the transformational development of programs and their algorithmic derivation from formal specifications. Automatic Program Development offers...

  17. Development and mechanical results of Zr-bearing ferritic steels

    Energy Technology Data Exchange (ETDEWEB)

    Tan, Lizhen [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-10-01

    The mission of the Nuclear Energy Enabling Technologies (NEET) program is to develop crosscutting technologies for nuclear energy applications. Advanced structural materials with superior performance at elevated temperatures are always desired for nuclear reactors, which can improve reactor economics, safety margins, and design flexibility. They benefit not only new reactors, including advanced light water reactors (LWRs) and fast reactors such as the sodium-cooled fast reactor (SFR) that is primarily designed for management of high-level wastes, but also life extension of the existing fleet when component exchange is needed. Developing and utilizing the modern materials science tools (experimental, theoretical, and computational tools) is an important path to more efficient alloy development and process optimization.

  18. Developing An Internship Program.

    Science.gov (United States)

    Chase, Valerie

    1984-01-01

    Provided are suggestions for developing museum/aquarium internship programs. These include writing detailed job descriptions, advertising, designing application forms asking all the information needed, supervising the interns, interviewing applicants as they were applying for a paid position, and others. (JN)

  19. Glass Formulation Development for INEEL Sodium-Bearing Waste

    International Nuclear Information System (INIS)

    Vienna, J.D.; Schweiger, M.J.; Smith, D.E.; Smith, H.D.; Crum, J.V.; Peeler, D.K.; Reamer, I.A.; Musick, C.A.; Tillotson, R.D.

    1999-01-01

    For about four decades, radioactive wastes have been collected and calcined from nuclear fuels reprocessing at the Idaho Nuclear Technology and Engineering Center (INTEC), formerly Idaho Chemical Processing Plant (ICPP). Over this time span, secondary radioactive wastes have also been collected and stored as liquid from decontamination, laboratory activities, and fuel-storage activities. These liquid wastes are collectively called sodium-bearing wastes (SBW). About 5.7 million liters of these wastes are temporarily stored in stainless steel tanks at the Idaho National Engineering and Environmental Laboratory (INEEL). Vitrification is being considered as an immobilization step for SBW with a number of treatment and disposal options. A systematic study was undertaken to develop a glass composition to demonstrate direct vitrification of INEEL's SBW. The objectives of this study were to show the feasibility of SBW vitrification, not a development of an optimum formulation. The waste composition is relatively high in sodium, aluminum, and sulfur. A specific composition and glass property restrictions, discussed in Section 2, were used as a basis for the development. Calculations based on first-order expansions of selected glass properties in composition and some general tenets of glass chemistry led to an additive (fit) composition (68.69 mass % SiO 2 , 14.26 mass% B 2 O 3 , 11.31 mass% Fe 2 O 3 , 3.08 mass% TiO 2 , and 2.67 mass % Li 2 O) that meets all property restrictions when melted with 35 mass % of SBW on an oxide basis, The glass was prepared using oxides, carbonates, and boric acid and tested to confirm the acceptability of its properties. Glass was then made using waste simulant at three facilities, and limited testing was performed to test and optimize processing-related properties and confirm results of glass property testing. The measured glass properties are given in Section 4. The viscosity at 1150 C, 5 Pa·s, is nearly ideal for waste-glass processing in

  20. Robotics Technology Development Program

    International Nuclear Information System (INIS)

    1994-02-01

    The Robotics Technology Development Program (RTDP) is a ''needs-driven'' effort. A lengthy series of presentations and discussions at DOE sites considered critical to DOE's Environmental Restoration and Waste Management (EM) Programs resulted in a clear understanding of needed robotics applications toward resolving definitive problems at the sites. A detailed analysis of the Tank Waste Retrieval (TWR), Contaminant Analysis Automation (CAA), Mixed Waste Operations (MWO), and Decontamination ampersand Dismantlement (D ampersand D). The RTDP Group realized that much of the technology development was common (Cross Cutting-CC) to each of these robotics application areas, for example, computer control and sensor interface protocols. Further, the OTD approach to the Research, Development, Demonstration, Testing, and Evaluation (RDDT ampersand E) process urged an additional organizational break-out between short-term (1--3 years) and long-term (3--5 years) efforts (Advanced Technology-AT). The RDTP is thus organized around these application areas -- TWR, CAA, MWO, D ampersand D and CC ampersand AT -- with the first four developing short-term applied robotics. An RTDP Five-Year Plan was developed for organizing the Program to meet the needs in these application areas

  1. Conical Magnetic Bearings Developed for Active Stall Control in Gas Turbine Engines

    Science.gov (United States)

    Trudell, Jeffrey J.; Kascak, Albert F.; Provenza, Andrew J.; Buccieri, Carl J.

    2004-01-01

    replaces the ball bearing in front of the compressor, and the second replaces the roller bearing behind the burner. The rig was made operational to 10,000 rpm under Smart Efficient Components funding, and both position and current adaptive vibration control have been demonstrated. Upon program completion, recommendations will be made as to the efficacy of the conical magnetic bearing for active stall control.

  2. Development of REBCO HTS Magnet of Magnetic Bearing for Large Capacity Flywheel Energy Storage System

    Science.gov (United States)

    Mukoyama, Shinichi; Matsuoka, Taro; Furukawa, Makoto; Nakao, Kengo; Nagashima, Ken; Ogata, Masafumi; Yamashita, Tomohisa; Hasegawa, Hitoshi; Yoshizawa, Kazuhiro; Arai, Yuuki; Miyazaki, Kazuki; Horiuchi, Shinichi; Maeda, Tadakazu; Shimizu, Hideki

    A flywheel energy storage system (FESS) is a promising electrical storage system that moderates fluctuation of electrical power from renewable energy sources. The FESS can charge and discharge the surplus electrical power repetitively with the rotating energy. Particularly, the FESS that utilizes a high temperature superconducting magnetic bearing (HTS bearing) is lower loss than conventional FESS that has mechanical bearing, and has property of longer life operation than secondary batteries. The HTS bearing consists of a HTS bulk and double-pancake coils used 2nd generation REBCO wires. In the development, the HTS double-pancake coils were fabricated and were provided for a levitation test to verify the possibility of the HTS bearing. We successfully confirmed the magnetic field was achieved to design value, and levitation force in the configuration of one YBCO bulk and five double pan-cake coils was obtained to a satisfactory force of 39.2 kN (4 tons).

  3. Development program business in Romania

    OpenAIRE

    Elena Ilie

    2014-01-01

    In the early 2000, in Romania, there were fewer programs to stimulating business environment and in this case the SMEs. After a transition period, various attempts to implement a financial and logistical support from the state were beginning to bear fruit with the year 2009 and take hold in 2011. Amid all legislative changes occurred, the novel proves its effectiveness against Romanian entrepreneurs and especially to young people, university graduates determined to make his way into the busin...

  4. Development of design method of thick rubber bearings for three-dimensional base isolation

    International Nuclear Information System (INIS)

    Yabana, Shuichi; Matuda, Akihiro

    2000-01-01

    Thick rubber bearings as 3-dimensional base isolators have been developed to reduce both horizontal and vertical seismic loads especially for equipment in Fast Breeder Reactors. In this report, a design method of thick rubber bearings is presented. To consider nonlinearity of vertical stiffness affected by vertical stress in the design of thick rubber bearings, Lindley's evaluation method of vertical stiffness is modified as an explicit form of vertical stress. We confirm that the presented method is efficient for design of the thick rubber bearings from comparing between test results and predicted values. Furthermore, rubber bearing tests are conducted with 1/3 scale models to evaluate mechanical properties of thick rubber bearings including ultimate limits. In the tests, horizontal and vertical characteristics of 1/3 scale model are compared with those of 1/6 scale model to discuss scale effect of test specimen. Ultimate limits such as failure shear strain of thick rubber bearings are obtained under various loading conditions. From the test results, we confirm that full scale thick rubber bearing to satisfy requirements is feasible. (author)

  5. Canadian fuel development program

    International Nuclear Information System (INIS)

    Gacesa, M.; Young, E.G.

    1992-11-01

    CANDU power reactor fuel has demonstrated an enviable operational record. More than 99.9% of the bundles irradiated have provided defect-free service. Defect excursions are responsible for the majority of reported defects. In some cases research and development effort is necessary to resolve these problems. In addition, development initiatives are also directed at improvements of the current design or reduction of fueling cost. The majority of the funding for this effort has been provided by COG (CANDU Owners' Group) over the past 10 to 15 years. This paper contains an overview of some key fuel technology programs within COG. The CANDU reactor is unique among the world's power reactors in its flexibility and its ability to use a number of different fuel cycles. An active program of analysis and development, to demonstrate the viability of different fuel cycles in CANDU, has been funded by AECL in parallel with the work on the natural uranium cycle. Market forces and advances in technology have obliged us to reassess and refocus some parts of our effort in this area, and significant success has been achieved in integrating all the Canadian efforts in this area. This paper contains a brief summary of some key components of the advanced fuel cycle program. (Author) 4 figs., tab., 18 refs

  6. Biofuels feedstock development program

    International Nuclear Information System (INIS)

    Wright, L.L.; Cushman, J.H.; Ehrenshaft, A.R.; McLaughlin, S.B.; McNabb, W.A.; Martin, S.A.; Ranney, J.W.; Tuskan, G.A.; Turhollow, A.F.

    1993-11-01

    The Department of Energy's (DOE's) Biofuels Feedstock Development Program (BFDP) leads the nation in the research, development, and demonstration of environmentally acceptable and commercially viable dedicated feedstock supply systems (DFSS). The purpose of this report is to highlight the status and accomplishments of the research that is currently being funded by the BFDP. Highlights summarized here and additional accomplishments are described in more detail in the sections associated with each major program task. A few key accomplishments include (1) development of a methodology for doing a cost-supply analysis for energy crops and the application of that methodology to looking at possible land use changes around a specific energy facility in East Tennessee; (2) preliminary documentation of the relationship between woody crop plantation locations and bird diversity at sites in the Midwest, Canada, and the pacific Northwest supplied indications that woody crop plantations could be beneficial to biodiversity; (3) the initiation of integrated switchgrass variety trials, breeding research, and biotechnology research for the south/southeast region; (4) development of a data base management system for documenting the results of herbaceous energy crop field trials; (5) publication of three issues of Energy Crops Forum and development of a readership of over 2,300 individuals or organizations as determined by positive responses on questionnaires

  7. Identifying polar bear resource selection patterns to inform offshore development in a dynamic and changing Arctic

    Science.gov (United States)

    Wilson, Ryan R.; Horne, Jon S.; Rode, Karyn D.; Regehr, Eric V.; Durner, George M.

    2014-01-01

    Although sea ice loss is the primary threat to polar bears (Ursus maritimus), little can be done to mitigate its effects without global efforts to reduce greenhouse gas emissions. Other factors, however, could exacerbate the impacts of sea ice loss on polar bears, such as exposure to increased industrial activity. The Arctic Ocean has enormous oil and gas potential, and its development is expected to increase in the coming decades. Estimates of polar bear resource selection will inform managers how bears use areas slated for oil development and to help guide conservation planning. We estimated temporally-varying resource selection patterns for non-denning adult female polar bears in the Chukchi Sea population (2008–2012) at two scales (i.e., home range and weekly steps) to identify factors predictive of polar bear use throughout the year, before any offshore development. From the best models at each scale, we estimated scale-integrated resource selection functions to predict polar bear space use across the population's range and determined when bears were most likely to use the region where offshore oil and gas development in the United States is slated to occur. Polar bears exhibited significant intra-annual variation in selection patterns at both scales but the strength and annual patterns of selection differed between scales for most variables. Bears were most likely to use the offshore oil and gas planning area during ice retreat and growth with the highest predicted use occurring in the southern portion of the planning area. The average proportion of predicted high-value habitat in the planning area was >15% of the total high-value habitat for the population during sea ice retreat and growth and reached a high of 50% during November 2010. Our results provide a baseline on which to judge future changes to non-denning adult female polar bear resource selection in the Chukchi Sea and help guide offshore development in the region. Lastly, our study provides a

  8. Investment in plant research and development bears fruit in China.

    Science.gov (United States)

    Chong, Kang; Xu, Zhihong

    2014-04-01

    Recent rapid progress in plant science and biotechnology in China demonstrates that China's stronger support for funding in plant research and development (R&D) has borne fruit. Chinese groups have contributed major advances in a range of fields, such as rice biology, plant hormone and developmental biology, genomics and evolution, plant genetics and epigenetics, as well as plant biotechnology. Strigolactone studies including those identifying its receptor and dissecting its complex structure and signaling are representative of the recent researches from China at the forefront of the field. These advances are attributable in large part to interdisciplinary studies among scientists from plant science, chemistry, bioinformatics, structural biology, and agronomy. The platforms provided by national facilities facilitate this collaboration. As well, efficient restructuring of the top-down organization of state programs and free exploration of scientists' interests have accelerated achievements by Chinese researchers. Here, we provide a general outline of China's progress in plant R&D to highlight fields in which Chinese research has made significant contributions.

  9. Program development fund

    International Nuclear Information System (INIS)

    1989-03-01

    It is the objective of the Fund to encourage innovative research to maintain the Laboratory's position at the forefront of science. Funds are used to explore new ideas and concepts that may potentially develop into new directions of research for the Laboratory and that are consistent with the major needs, overall goals, and mission of the Laboratory and the DOE. The types of projects eligible for support from PDF include: work in forefront areas of science and technology for the primary purpose of enriching Laboratory research and development capabilities; advanced study of new hypotheses, new experimental concepts, or innovative approaches to energy problems; experiments directed toward ''proof of principle'' or early determination of the utility of a new concept; and conception, design analyses, and development of experimental devices, instruments, or components. This report is a review of these research programs

  10. Development of active magnetic bearings and ferrofluid seals toward oil free sodium pumps

    International Nuclear Information System (INIS)

    Sreedhar, B.K.; Kumar, R. Nirmal; Sharma, Prashant; Ruhela, Shivprakash; Philip, John; Sundarraj, S.I.; Chakraborty, N.; Mohana, M.; Sharma, Vijay; Padmakumar, G.; Nashine, B.K.; Rajan, K.K.

    2013-01-01

    Sodium centrifugal pumps employ conventional oil cooled bearings and mechanical seals to support the rotor assembly outside sodium and to seal the cover gas from the atmosphere. Although engineered safety features are incorporated in the design and detailed operational procedures formulated to ensure that no oil contamination of sodium can occur, there have been incidents of oil ingress into sodium. A design variant that eliminates the need for oil in top bearings and seals is therefore a promising option. This paper discusses the work in progress to develop a magnetic bearing and ferrofluid seal combination that can achieve this purpose

  11. ABC Technology Development Program

    International Nuclear Information System (INIS)

    1994-01-01

    The Accelerator-Based Conversion (ABC) facility will be designed to accomplish the following mission: 'Provide a weapon's grade plutonium disposition capability in a safe, economical, and environmentally sound manner on a prudent schedule for [50] tons of weapon's grade plutonium to be disposed on in [20] years.' This mission is supported by four major objectives: provide a reliable plutonium disposition capability within the next [15] years; provide a level of safety and of safety assurance that meets or exceeds that afforded to the public by modern commercial nuclear power plants; meet or exceed all applicable federal, state, and local regulations or standards for environmental compliance; manage the program in a cost effective manner. The ABC Technology Development Program defines the technology development activities that are required to accomplish this mission. The technology development tasks are related to the following topics: blanket system; vessel systems; reactivity control systems; heat transport system components; energy conversion systems; shutdown heat transport systems components; auxiliary systems; technology demonstrations - large scale experiments

  12. WANO. Development, programs, challenges

    International Nuclear Information System (INIS)

    Haferburg, Manfred

    2011-01-01

    In the wake of the accident at the Soviet RBMK reactor unit 4 in Chernobyl the nuclear industry founded the World Association of Nuclear Operators (WANO). To this day, the purpose of the organization has been to enhance worldwide cooperation of nuclear industry and, in this way, strengthen the safety and availability of nuclear power plants. Following some first steps after 1986, the charter of the organization was signed at the WANO constituent assembly in Moscow on May 15 and 16, 1989. The member companies thus committed themselves to support WANO's mission. WANO was established for these purposes: ''The mission of WANO is to maximize the safety and reliability of nuclear power plants worldwide by working together to assess, benchmark and improve performance through mutual support, exchange of information, and emulation of best practices.'' The WANO programs developed speedily thereafter. The focus was on peer reviews. In 2000, the first interim objective had been reached: Fifty percent of all member nuclear power plants had undergone peer reviews. In addition, plant-related peer reviews were extended throughout all operator organizations, and corporate peer reviews were developed. The other WANO programs as well, i.e. exchanges of experience, technical support, and performance indicators, exerted more and more influence on industry. Peer reviews covered entire operator organizations, and corporate peer reviews were developed. The worldwide paradigm shift in evaluating the use of nuclear power, and the associated construction programs for new nuclear power plants already in their implementation phase, assigned a new quality to the work of WANO. The organization is preparing a long-term strategy in the face of the challenges to be expected. The ultimate objective of these efforts is to support member organizations from the first preparations of a nuclear power plant project to the end of commercial operation. (orig.)

  13. Development testing of high temperature bearings for SP-100 control drive assemblies

    Science.gov (United States)

    Dalcher, Alfred W.; Kjaer-Olsen, Christian G.; Martinez, Carlos; Ogawa, Stanley Y.; Springer, Dwight R.; Yaspo, Robert

    1992-01-01

    Initial phases of two distinct SP-100 control drive assembly bearing test programs were successfully completed at elevated temperature in vacuum. The first was for the reflector drive line spherical self-aligning bearings. Each bearing consisted of a carbon-graphite ball mounted on an aluminum oxide-coated Ta-10%W shaft, captured by an aluminum oxide-coated Ta-10%W socket. One set of these bearings was exposed to temperatures up to 1180K (1665°F) at 1.33×10-6 Pa (1×10-8 torr) and subjected to 38000 cycles of motion. Friction coefficients were found to be between 0.11 and 0.25 over the full range of operation. Overall performance of the bearings was excellent, with only slight wear observed. The second test program was for the safety rod slider bearing. Zirconium carbide coated Nb-1%Zr bearings pads were stroked inside a molybdenum tube at temperatures up to 1422 K (2100°F) at ˜1.33×10-6 Pa with a normal load of 1.02 Kg between each sliding surface. Coefficients of sliding friction were found to increase from 0.90 at 293 K to 1.20 at 1422 K prior to high temperature dwells. Results were consistent over the range of stroke velocities; 5.1 to 51 mm (0.2 to 2.0 inches) per second. Following dwells of 92, 72, and 110 hours at 1422 K, static friction coefficients as high as 5.4 were observed prior to initiation of sliding, after which sliding friction coefficients of ˜1.6 were seen. Breakaway forces were well within the actuator design limits.

  14. Development of the water-lubricated thrust bearing of the hydraulic turbine generator

    International Nuclear Information System (INIS)

    Inoue, K; Deguchi, K; Okude, K; Fujimoto, R

    2012-01-01

    In hydropower plant, a large quantities of turbine oil is used as machine control pressure oil and lubricating oil. If the oil leak out from hydropower plant, it flows into a river. And such oil spill has an adverse effect on natural environment because the oil does not degrade easily. Therefore the KANSAI and Hitachi Mitsubishi Hydro developed the water-lubricated thrust bearing for vertical type hydraulic turbine generator. The water-lubricated bearing has advantages in risk avoidance of river pollution because it does not need oil. For proceeding the development of the water-lubricated thrust bearing, we studied following items. The first is the examination of the trial products of water lubricating liquid. The second is the study of bearing structure which can satisfy bearing performance such as temperature characteristic and so on. The third is the mock-up testing for actual application in the future. As a result, it was found that the water-lubricated thrust bearing was technically applicable to actual equipments.

  15. Development and characterization of magnetic HTS bearings for a 400 kW synchronous HTS motor

    International Nuclear Information System (INIS)

    Kummeth, P; Ries, G; Nick, W; Neumueller, H-W

    2004-01-01

    Promising results of static and dynamic investigations on various journal type test bearings encouraged us to develop a scaled-up HTS bearing, able to carry the HTS rotor of a 400 kW superconducting motor. The stator, a YBCO hollow cylinder of 203 mm inner diameter and 250 mm length, is cooled by liquid nitrogen. Permanent magnet rings with a diameter of 200 mm were mounted on a shaft with alternating polarity. Characterization of the bearing capacity was performed with three different YBCO stators at temperatures between 66 and 86 K in a test set-up. A significant influence of the temperature was found. At a stator temperature of 72 K and a rotation frequency of 25 Hz (corresponding to nominal motor speed) a radial bearing force of 2700 N was measured for the shaft at centre position. Under rotation of the shaft the bearing capacity is reduced. At present our results range within the highest radial bearing capacities reported world-wide

  16. Future developments and applications of nitrogen-bearing steels ...

    Indian Academy of Sciences (India)

    Abstract. After considerations related with the global frame of the demand of society in the field of materials and some recalling of basic properties and principles of nitrogen alloying, possible future developments are listed and discussed.

  17. The effects of a 12-week program of static upper extremity weight bearing exercises on weight bearing in children with hemiplegic type of cerebral palsy

    Directory of Open Access Journals (Sweden)

    P. Jayaraman

    2010-01-01

    Full Text Available The  major  objective  of  this  study  was  to  quantify  the  effects  of a  12-week  program  of  weight  bearing  exercises  on  weight  borne  through  the hand and grip pressures in children with hemiplegic cerebral palsy. This study also sought to monitor the change in spasticity immediately following weight-bearing  exercises.  A  quasi-experimental,  one  group  pre-test,  post-test  study  was used. Eleven children with hemiplegic type of cerebral palsy from a special school in KwaZulu Natal participated after fully informed written consent. The intervention consisted of a 12-week program of weight bearing. The Tekscan Grip system was used to quantify weight borne through the hand during extended arm prone and quadruped positions and whilst holding a pencil and a tumbler. The modified Ashworth grading of spasticity was used to monitor spasticity. The data was analysed using the random effects GLS model Wald Chi Square test. Significant increases in contact pressure in extended arms prone (p=0,012 and quadruped (p=0,002 and when holding a pencil (p=0,045 was noted post-test compared to pre-test. Significant increases in contact area of the hand was also noted in prone (p=0,000, quadruped (p=0, 03 at assessment 7 and when holding a pencil (p=0,035.  A significant decrease in spasticity during elbow extension (p=0,004, and wrist flexion (p=0,026 and extension (p=0,004 was noted. An overall significant effect of static weight bearing exercises on weight borne through the hands, grip strength and spasticity justifies the use of static weight-bearing in therapy.

  18. Advanced Transmission Components Investigation Program. Bearing and Seal Development.

    Science.gov (United States)

    1980-08-01

    perf iot r11cC, aS rrt~iti~f( Chear c. Ini August iof 1977 the Timkert Company of Catnioin, hio, con- tracteif i fai,t I and1)( test 11rr IIV.01Led...LND Figure B - 17. Cup. Rollers and Cage Used a( IDrive End of Shaft 78-5 in Test Setup No. 4 (Sheet I of 2). t)4 ROLLERS CAGE 78-17 Figure B -17. Cup

  19. Oil-free bearing development for high-speed turbomachinery in distributed energy systems – dynamic and environmental evaluation

    Directory of Open Access Journals (Sweden)

    Tkacz Eliza

    2015-09-01

    Full Text Available Modern distributed energy systems, which are used to provide an alternative to or an enhancement of traditional electric power systems, require small size highspeed rotor turbomachinery to be developed. The existing conventional oil-lubricated bearings reveal performance limits at high revolutions as far as stability and power loss of the bearing are concerned. Non-conventional, oil-free bearings lubricated with the machine working medium could be a remedy to this issue. This approach includes a correct design of the machine flow structure and an accurate selection of the bearing type. Chosen aspects of the theoretical and experimental investigations of oil-free bearings and supports; including magnetic, tilting pad, pressurized aerostatic and hydrostatic bearings as well as some applications of oil-free bearing technology for highspeed turbomachinery; are described in the paper.

  20. Review of FY 2001 Development Work for Vitrification of Sodium Bearing Waste

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Dean Dalton; Barnes, Charles Marshall

    2002-09-01

    Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated by the Settlement Agreement between the Department of Energy and the State of Idaho. This report discusses significant findings from vitrification technology development during 2001 and their impacts on the design basis for SBW vitrification.

  1. Review of FY2001 Development Work for Vitrification of Sodium Bearing Waste

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, C.M.; Taylor, D.D.

    2002-09-09

    Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated by the Settlement Agreement between the Department of Energy and the State of Idaho. This report discusses significant findings from vitrification technology development during 2001 and their impacts on the design basis for SBW vitrification.

  2. Accelerated Bearing Life-time Test Rig Development for Low Speed Data Acquisition

    Directory of Open Access Journals (Sweden)

    Andreas Klausen

    2017-07-01

    Full Text Available Condition monitoring plays an important role in rotating machinery to ensure reliability of the equipment, and to detect fault conditions at an early stage. Although health monitoring methodologies have been thoroughly developed for rotating machinery, low-speed conditions often pose a challenge due to the low signal-to-noise ratio. To this aim, sophisticated algorithms that reduce noise and highlight the bearing faults are necessary to accurately diagnose machines undergoing this condition. In the development phase, sensor data from a healthy and damaged bearing rotating at low-speed is required to verify the performance of such algorithms. A test rig for performing accelerated life-time testing of small rolling element bearings is designed to collect necessary sensor data. Heavy loads at high-speed conditions are applied to the test bearing to wear it out fast. Sensor data is collected in intervals during the test to capture the degeneration features. The main objective of this paper is to provide a detailed overview for the development and analysis of this test rig. A case study with experimental vibration data is also presented to illustrate the efficacy of the developed test rig.

  3. Review of FY2001 Development Work for Vitrification of Sodium Bearing Waste

    International Nuclear Information System (INIS)

    Barnes, C.M.; Taylor, D.D.

    2002-01-01

    Treatment of sodium-bearing waste (SBW) at the Idaho Nuclear Technology and Engineering Center (INTEC) within the Idaho National Engineering and Environmental Laboratory is mandated by the Settlement Agreement between the Department of Energy and the State of Idaho. This report discusses significant findings from vitrification technology development during 2001 and their impacts on the design basis for SBW vitrification

  4. Research and development project for flywheel energy storage system using high-temperature superconducting magnetic bearing

    International Nuclear Information System (INIS)

    Shinagawa, Jiro; Ishikawa, Fumihiko

    1996-01-01

    Recent progress in the research and development of an yttrium-based oxide high-temperature superconductor has enabled the production of a large-diameter bulk with a strong flux-pinning force. A combination of this superconductor and a permanent magnet makes it feasible to fabricate a non-contact, non-controlled superconducting magnetic bearing with a very small rotational loss. Use of the superconducting magnetic bearing for a flywheel energy storage system may pave the way to the development of a new energy storage system that has great energy storage efficiency. >From relevant data measured with a miniature model of the high-temperature superconducting magnetic bearing, a conceptual design of an 8 MWh flywheel energy storage system was developed, using the new bearing which proved to be potentially capable of achieving a high energy storage efficiency of 84%. A 100 Wh-class experimental system was install that attained a high revolution rate of 17.000 rpm. (author)

  5. Development of a pan-Arctic monitoring plan for polar bears: Background paper

    Science.gov (United States)

    Vongraven, Dag; Peacock, Lily

    2011-01-01

    Polar bears (Ursus maritimus), by their very nature, and the extreme, remote environment in which they live, are inherently difficult to study and monitor. Monitoring polar bear populations is both arduous and costly and, to be effective, must be a long-term commitment. There are few jurisdictional governments and management boards with a mandate for polar bear research and management, and many have limited resources. Although population monitoring of polar bears has been a focus to some degree within most jurisdictions around the Arctic, of the 19 subpopulations recognised by the IUCN/Species Survival Commission Polar Bear Specialist Group (PBSG), adequate scientific trend data exist for only three of the subpopulations, fair trend data for five and poor or no trend data for the remaining 11 subpopulations (PBSG 2010a). There are especially critical knowledge gaps for the subpopulations in East Greenland, in the Russian Kara and Laptev seas, and in the Chukchi Sea, which is shared between Russia and the United States. The range covered by these subpopulations represents a third of the total area (approx. 23 million km2) of polar bears’ current range, and more than half if the Arctic Basin is included. If we use popular terms, we know close to nothing about polar bears in this portion of their range.As summer sea-ice extent, and to a lesser degree, spring-time extent, continues to retreat, outpacing model forecasts (Stroeve et al. 2007, Pedersen et al. 2009), polar bears face the challenge of adapting to rapidly changing habitats. There is a need to use current and synthesised information across the Arctic, and to develop new methods that will facilitate monitoring to generate new knowledge at a pan-Arctic scale. The circumpolar dimension can be lost when efforts are channelled into regional monitoring. Developing and implementing a plan that harmonises local, regional and global efforts will increase our power to detect and understand important trends for polar

  6. Operating experience of gas bearing helium circulators in HTGR development facility

    International Nuclear Information System (INIS)

    Shimomura, H.; Kawaji, S.; Fujisaki, K.; Ihizuka, T.

    1988-01-01

    The large scale helium gas test facility (HENDEL) has been constructed and operated since March 1982 at the Japan Atomic Energy Research Institute to develop HTGR components. The five electric driven gas circulators with dynamic gas bearings are used to circulate the helium gas of 4MPa and 400 deg. C in loops for their compactness, gas tightness, easy maintenance and free from gas contamination. All of these circulators are variable speed types of 3,000 to 12,000 rpm and have the same gas bearings and electric motors. The four machines among them are equipped with centrifugal impeller and one other machine has regenerative type, and the weight of both type rotors are nearly the same. After the troubles and repairing, both type of circulators were tested and the vibration characteristics were measured as preventing maintenance. From the test and measurements of the circulators, it was presumed that the first trouble on regenerative type was caused from excess unbalance force by falling off of a small pin from the rotating part and the second severe trouble on it was caused by the whipping in gas bearing. The static load on tilting pads indicated close relations to occurrence of the whirling through the measurements. It is recognized that fine balancing of the rotors and delicate clearance adjustment of the bearings are very important for the rotor stability and that the mechanism should be designed and machined so precise as to be adjustable. As the gas bearing would be damaged in an instantaneously short time, the monitoring technique for it should be so fast and predictive as to prevent serious damage. Through the tests, the vibration spectrum monitoring method seems to be predictive and useful for early detection of the shaft instability. It will be concluded that the gas bearing machine is an excellent system in its design philosophy, however, it also needs highly precise machining and delicate maintenance technique. 4 refs, 10 figs, 1 tab

  7. Gender quotas in development programming

    NARCIS (Netherlands)

    Windt, van der Peter; Humphreys, Macartan; Sanchez de la Sierra, Raul

    2018-01-01

    We examine whether gender quotas introduced by development agencies empower women. As part of a development program, an international organization created community management committees in 661 villages to oversee village level program expenditures. In a randomly selected half of these villages the

  8. 78 FR 50410 - Black Bear Development Holdings, LLC; Supplemental Notice that Initial Market-Based Rate Filing...

    Science.gov (United States)

    2013-08-19

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER13-2143-000] Black Bear Development Holdings, LLC; Supplemental Notice that Initial Market-Based Rate Filing Includes Request for... Black Bear Development Holdings, LLC's application for market-based rate authority, with an accompanying...

  9. Report on the biological monitoring program for Bear Creek at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, 1989-1994

    Energy Technology Data Exchange (ETDEWEB)

    Hinzman, R.L. [ed.; Beauchamp, J.J.; Cada, G.F.; Peterson, M.J. [and others

    1996-04-01

    The Bear Creek Valley watershed drains the area surrounding several closed Oak Ridge Y-12 Plant waste disposal facilities. Past waste disposal practices in the Bear Creek Valley resulted in the contamination of Bear Creek and consequent ecological damage. Ecological monitoring by the Biological Monitoring and Abatement Program (BMAP) was initiated in the Bear Creek watershed in May 1984 and continues at present. Studies conducted during the first year provided a detailed characterization of the benthic invertebrate and fish communities in Bear Creek. The initial characterization was followed by a biological monitoring phase in which studies were conducted at reduced intensities.

  10. Report on the biological monitoring program for Bear Creek at the Oak Ridge Y-12 Plant, Oak Ridge, Tennessee, 1989-1994

    International Nuclear Information System (INIS)

    Hinzman, R.L.; Beauchamp, J.J.; Cada, G.F.; Peterson, M.J.

    1996-04-01

    The Bear Creek Valley watershed drains the area surrounding several closed Oak Ridge Y-12 Plant waste disposal facilities. Past waste disposal practices in the Bear Creek Valley resulted in the contamination of Bear Creek and consequent ecological damage. Ecological monitoring by the Biological Monitoring and Abatement Program (BMAP) was initiated in the Bear Creek watershed in May 1984 and continues at present. Studies conducted during the first year provided a detailed characterization of the benthic invertebrate and fish communities in Bear Creek. The initial characterization was followed by a biological monitoring phase in which studies were conducted at reduced intensities

  11. Nondimensional characterization and asymptotic model development for multifunctional structures with application to load-bearing antennas

    International Nuclear Information System (INIS)

    Santapuri, Sushma; Bechtel, Stephen E

    2014-01-01

    This paper (i) presents a mathematical approach to formulate leading-order models for complex multifunctional systems with coupled thermomechanical and electromagnetic field interactions, and (ii) demonstrates its applicability to the modeling and analysis of a load-bearing antenna, a multifunctional sensing and transmitting device integrated with a load-bearing structure. Starting from first-principle equations, i.e. the thermomechanical balance laws coupled with Maxwell’s equations, nondimensionalization and perturbation techniques are employed to formulate a leading-order model for the coupled system. Depending on the design of the structure and nature of the excitation, the nondimensional numbers arising in the coupled multifunctional system are quantified, and through a relative ordering of these quantities, the dominant physical effects are extracted. The resulting dominant effects determine the regime of operation of the structure, and in turn dictate the appropriate computational model. This approach is demonstrated through an application to a load-bearing antenna for a prototypical design. The resulting leading-order model is subsequently solved, and the electrical and structural response of the load-bearing antenna is analyzed and compared for different combinations of material properties. The framework introduced in this paper is envisioned to have applications in developing leading-order models for a wide range of complex multifunctional systems and can be utilized for their efficient design. (paper)

  12. Technical Leadership Development Program

    Science.gov (United States)

    2014-04-30

    will be focused on their view of the pros / cons of the ‘how’ they are going about their assigned task as opposed to ‘what’ they are proposing. As...Leadership Style (Y) M4.0 Simula on 1- Leadership Value Proposi on (Y) Some hidden (secret) mo va ons for roles in scenarios/vigne es Develop SWOT

  13. Technical Leadership Development Program

    Science.gov (United States)

    2010-12-13

    the traditional tenets of leadership and management , systems thinking, understanding SOS issues, and thinking and acting holistically. Our research...international element 2.0 Enterprise Leadership and Management UNCLASSIFIED Contract Number: H98230-08-D-0171 DO 002. TO002, RT 004 Report No...mechanisms for leadership of the overall technical effort, for systems engineering, for requirements, management , and for systems integration. o Develop

  14. The use of Teddy Bears to help develop interpersonal context to promote intrinsic motivation

    Directory of Open Access Journals (Sweden)

    Rabb Andrews, Tamatha

    2004-12-01

    Full Text Available This article is based on the findings of using a teddy bear as a tool to provide a way of increasing pupils ' motivation toward learning by means of using a stuffed animal such as a teddy bear named Ken Bear and relating it to learning a L2. It was developed in hopes to improve not only the motivation of students but give a positive backwash on the institution itself by giving the school a positive interpersonal context. Voluntary students participated in this project, which consisted of taking care of a teddy bear as a friend or playmate for a day or a few days. At the end of such time, the students would write a short entry into the bear ' s diary in English if possible, if not, in Spanish or just a picture with a few words. Results indicated that this project was a huge success based on the opinions of students, teachers and parents. El siguiente artículo esta basado en los resultados obtenidos de una investigación cuyo objetivo fue el utilizar un oso de peluche como una herramienta para incrementar la motivación de los estudiantes hacia el aprendizaje del inglés como segunda lengua. Esta trabajo investigativo fue desarrollado esperando mejorar no solo la motivación de los educandos por medio de este recurso novedoso, sino también darle un giro positivo al ambiente de relaciones interpersonales en la institución donde se realizo este proyecto.

  15. NCG turbocompressor development program

    Energy Technology Data Exchange (ETDEWEB)

    Nichols, K.E.

    1997-12-31

    Barber-Nichols, Pacific Gas and Electric and UNOCAL as an industry group applied for a DOE grant under the GTO to develop a new type of compressor that could be used to extract non-condensable gas (NCG) from the condensers of geothermal power plants. This grant (DE-FG07-951A13391) was awarded on September 20, 1995. The installation and startup of the turbocompressor at the PG&E Geysers Unit 11 is covered by this paper. The turbocompressor has operated several days at 17000rpm while the plant was producing 50 to 70 MW.

  16. Wetland Program Development Grants (WPDGs)

    Data.gov (United States)

    U.S. Environmental Protection Agency — The Wetland Grant Database (WGD) houses grant data for Wetland Program Development Grants (created by EPA in 1990 under the Clean Water Act Section 104(b)(3)...

  17. Visualization program development using Java

    International Nuclear Information System (INIS)

    Sasaki, Akira; Suto, Keiko

    2002-03-01

    Method of visualization programs using Java for the PC with the graphical user interface (GUI) is discussed, and applied to the visualization and analysis of 1D and 2D data from experiments and numerical simulations. Based on an investigation of programming techniques such as drawing graphics and event driven program, example codes are provided in which GUI is implemented using the Abstract Window Toolkit (AWT). The marked advantage of Java comes from the inclusion of library routines for graphics and networking as its language specification, which enables ordinary scientific programmers to make interactive visualization a part of their simulation codes. Moreover, the Java programs are machine independent at the source level. Object oriented programming (OOP) methods used in Java programming will be useful for developing large scientific codes which includes number of modules with better maintenance ability. (author)

  18. Kodak AMSD Mirror Development Program

    Science.gov (United States)

    Matthews, Gary; Dahl, Roger; Barrett, David; Bottom, John; Russell, Kevin (Technical Monitor)

    2002-01-01

    The Advanced Mirror System Demonstration Program is developing minor technology for the next generation optical systems. Many of these systems will require extremely lightweight and stable optics due to the overall size of the primary mirror. These segmented, deployable systems require new technology that AMSD is developing. The on-going AMSD program is a critical enabler for Next Generation Space Telescope (NGST) which will start in 2002. The status of Kodak's AMSD mirror and future plans will be discussed with respect to the NGST program.

  19. The development on-line monitoring system of active magnetic bearings for HTR-10GT

    International Nuclear Information System (INIS)

    Shi Zhengang; Shi Lei; Zha Meisheng; Yu Suyuan

    2005-01-01

    High Temperature Gas-cooled Reactor (HTR) is recognized as an advanced type of reactor incorporating many design enhancements such as inherent safety features, fuel cycle flexibility, highly fuel utilization, highly efficient electricity generation and process heat application. The research and development of HTR started at the middle of the 1970's, and came to be a part of the Chinese High Technology Program in 1986. A plan to build a 10 MW High Temperature Gas-cooled Reactor (HTR-10) was approved by the State Science and Technology Commission in 1990, and in 1995 the construction was initiated at the Institute of Nuclear Energy Technology (INET), Tsinghua University. The full power 10 MW operation for 72 hours have reached in 2003, and have been checked and accepted by the State Science and Technology Commission. In order to advance the HTR-10 performance, the project of the Helium Gas Turbine Generator for the HTR-10 was authorized by the State Science and Technology Commission, and stared in 2003. In this project, active magnetic bearings (AMBs) are chosen to support the generator rotor and the turbocompressor rotor in the power conversion unit because of their numerous advantages over the conventional bearings. In order to detect how the AMB system works in operation and make diagnosis whether the system behaves normally or not, the monitoring system based on the virtual instruments is designed to monitor the working conditions of the PCU, and to ensure its normal operation. This monitoring system consists of the industry personal computer (PC), the data acquisition system, the measurement transmitters and the LabVIEW system platform. It is located at the PCU control room, and communicates with the master control room by Controller Area Net (CAN). The development is divided into the following three steps: First, a data acquisition platform to collect and acquire all the necessary and useful data from the operation of the AMB system is developed. Second, the

  20. Program for tests on magnetic bearing suspended rotor dynamics for gas turbine high temperature reactor (GTHTR300)

    International Nuclear Information System (INIS)

    Takada, Shoji; Takizuka, Takakazu; Kunitomi, Kazuhiko; Kosugiyama, Shinichi; Yan, Xing

    2003-01-01

    A program for test on rotor dynamics was planned for the turbo-machine of the Gas Turbine High Temperature Reactor (GTHTR300). The rotor system of the turbo-machine consists of a turbo-compressor rotor and a generator rotor connected with a flexible coupling, each suspended with two radial magnetic bearings. The rotors, which are flexible rotors, pass over the critical speeds of bending mode. The magnetic bearing is required to have a high load capacity, about 10 times larger than any built thus far to support a flexible rotor. In the rotor design, the standard limit of the vibration amplitude of 75 μm at the rated rotational speed of 3,600 rpm was fulfilled by optimizing the stiffness of the magnetic bearings. A test apparatus was designed to verify the design of the magnetic bearing suspended turbo-machine rotor of the GTHTR300. The test apparatus is composed of 1/3-scale test rotors, which are connected with a flexible coupling and driven by a variable speed motor. The test magnetic bearing was designed within the state-of-the-art technology to have a load capacity about 1/10 of that of the actual one. The test rotors were designed to closely simulate the critical speeds and vibration modes of the actual ones. This paper shows the test apparatus and the test plan for the magnetic bearing suspended rotor system. The present study is entrusted from the Ministry of Education, Culture, Sports, Science and Technology of Japan. (author)

  1. Commercial Crew Development Program Overview

    Science.gov (United States)

    Russell, Richard W.

    2011-01-01

    NASA's Commercial Crew Development Program is designed to stimulate efforts within the private sector that will aid in the development and demonstration of safe, reliable, and cost-effective space transportation capabilities. With the goal of delivery cargo and eventually crew to Low Earth Orbit (LEO) and the International Space Station (ISS) the program is designed to foster the development of new spacecraft and launch vehicles in the commercial sector. Through Space Act Agreements (SAAs) in 2011 NASA provided $50M of funding to four partners; Blue Origin, The Boeing Company, Sierra Nevada Corporation, and SpaceX. Additional, NASA has signed two unfunded SAAs with ATK and United Space Alliance. This paper will give a brief summary of these SAAs. Additionally, a brief overview will be provided of the released version of the Commercial Crew Development Program plans and requirements documents.

  2. NASA Procurement Career Development Program

    Science.gov (United States)

    1987-01-01

    The NASA Procurement Career Development Program establishes an agency-wide framework for the management of career development activity in the procurement field. Within this framework, installations are encouraged to modify the various components to meet installation-specific mission and organization requirements. This program provides a systematic process for the assessment of and planning for the development, training, and education required to increase the employees' competence in the procurement work functions. It includes the agency-wide basic knowledge and skills by career field and level upon which individual and organizational development plans are developed. Also, it provides a system that is compatible with other human resource management and development systems, processes, and activities. The compatibility and linkage are important in fostering the dual responsibility of the individual and the organization in the career development process.

  3. Mechanical model development of rolling bearing-rotor systems: A review

    Science.gov (United States)

    Cao, Hongrui; Niu, Linkai; Xi, Songtao; Chen, Xuefeng

    2018-03-01

    The rolling bearing rotor (RBR) system is the kernel of many rotating machines, which affects the performance of the whole machine. Over the past decades, extensive research work has been carried out to investigate the dynamic behavior of RBR systems. However, to the best of the authors' knowledge, no comprehensive review on RBR modelling has been reported yet. To address this gap in the literature, this paper reviews and critically discusses the current progress of mechanical model development of RBR systems, and identifies future trends for research. Firstly, five kinds of rolling bearing models, i.e., the lumped-parameter model, the quasi-static model, the quasi-dynamic model, the dynamic model, and the finite element (FE) model are summarized. Then, the coupled modelling between bearing models and various rotor models including De Laval/Jeffcott rotor, rigid rotor, transfer matrix method (TMM) models and FE models are presented. Finally, the paper discusses the key challenges of previous works and provides new insights into understanding of RBR systems for their advanced future engineering applications.

  4. Experimental research and development of main circulation pump bearings in reactor plants using heavy liquid-metal coolants

    International Nuclear Information System (INIS)

    Zudin, A.; Beznosov, A.; Chernysh, A.; Prikazchikov, G.

    2015-01-01

    At the present time, specialists in Russia are engaged in designing the BREST-OD-300 fast neutron lead-coolant reactor plant. There is currently no experience in designing and operating axial pumps of lead-coolant reactor plants, including one of their major units – bearing unit. Selection and substantiation of operating and structural parameters of plain friction bearings used in main circulation pumps of reactor plants running on heavy liquid-metal coolants are important tasks that are solved at the NNSTU. Development of a feasible procedure for designing bearings and its components operating within the structure of the main circulation pump of a reactor plant running on a heavy liquid-metal coolant as well as guidelines for an optimized structural scheme of such bearings set a goal of performing a range of theoretically-calculated and experimental works. The report contains testing data of a hydrostatic bearing with reciprocal fricative choking tested on the NNSTU FT-4 bench running on a lead coolant within the range of 420-500degC. There have been presented a scheme of a bench for testing a contact friction bearing on a high-temperature coolant and the results of investigation tests of bearings of such type at T = 450 ÷ 500degC. Material of the bearing sleeve is steel 08X18H10T, and a possibility is provided with regard to installation of the bearing sleeves and shaft made of non-metal materials (ceramic materials, silicified graphite, etc.). The presented testing data of plain friction bearings operating in a high-temperature heavy liquid-metal coolant will serve as a ground for making an alternative choice of a plain friction bearing for the main circulation pump of a reactor plant running on a heavy liquid-metal coolant. (author)

  5. Research and development program 1985

    International Nuclear Information System (INIS)

    1984-01-01

    In this report the research and development program of the GSI Darmstadt is described. It concerns heavy ion reactions, nuclear structure studies, exotic nuclei, nuclear theory, atomic collisions with heavy ions, atomic spectroscopy, the interaction of heavy ions with matter, atomic theory, biological studies with heavy ions, nuclear track techniques, UNILAC developments, acquisition of experimental data, and the development of new accelerators, ion sources, targets, and detectors. (HSI) [de

  6. Leadership Development Program Final Project

    Science.gov (United States)

    Parrish, Teresa C.

    2016-01-01

    TOSC is NASA's prime contractor tasked to successfully assemble, test, and launch the EM1 spacecraft. TOSC success is highly dependent on design products from the other NASA Programs manufacturing and delivering the flight hardware; Space Launch System(SLS) and Multi-Purpose Crew Vehicle(MPCV). Design products directly feed into TOSC's: Procedures, Personnel training, Hardware assembly, Software development, Integrated vehicle test and checkout, Launch. TOSC senior management recognized a significant schedule risk as these products are still being developed by the other two (2) programs; SVE and ACE positions were created.

  7. Professorship: A Faculty Development Program.

    Science.gov (United States)

    Davis, Todd M.; Davis, Jane F.

    1987-01-01

    A faculty development program at a traditionally black college was designed to enhance the ability of graduate faculty to supervise research activities of graduate students. Focus was on interpersonal problem solving in advisement and professional issues; classroom techniques of discussion teaching, case methods, and psychodrama encouraged the…

  8. Child Development Program Evaluation Scale.

    Science.gov (United States)

    Fiene, Richard J.

    The Child Development Program Evaluation Scale (CDPES) is actually two scales in one, a licensing scale and a quality scale. Licensing predictor items have been found to predict overall compliance of child day care centers with state regulations in four states. Quality scale items have been found to predict the overall quality of child day care…

  9. Impacts of rural development on Yellowstone wildlife: linking grizzly bear Ursus arctos demographics with projected residential growth

    Science.gov (United States)

    Schwartz, Charles C.; Gude, Patricia H.; Landenburger, Lisa; Haroldson, Mark A.; Podruzny, Shannon

    2012-01-01

    Exurban development is consuming wildlife habitat within the Greater Yellowstone Ecosystem with potential consequences to the long-term conservation of grizzly bears Ursus arctos. We assessed the impacts of alternative future land-use scenarios by linking an existing regression-based simulation model predicting rural development with a spatially explicit model that predicted bear survival. Using demographic criteria that predict population trajectory, we portioned habitats into either source or sink, and projected the loss of source habitat associated with four different build out (new home construction) scenarios through 2020. Under boom growth, we predicted that 12 km2 of source habitat were converted to sink habitat within the Grizzly Bear Recovery Zone (RZ), 189 km2 were converted within the current distribution of grizzly bears outside of the RZ, and 289 km2 were converted in the area outside the RZ identified as suitable grizzly bear habitat. Our findings showed that extremely low densities of residential development created sink habitats. We suggest that tools, such as those outlined in this article, in addition to zoning and subdivision regulation may prove more practical, and the most effective means of retaining large areas of undeveloped land and conserving grizzly bear source habitat will likely require a landscape-scale approach. We recommend a focus on land conservation efforts that retain open space (easements, purchases and trades) coupled with the implementation of ‘bear community programmes’ on an ecosystem wide basis in an effort to minimize human-bear conflicts, minimize management-related bear mortalities associated with preventable conflicts and to safeguard human communities. Our approach has application to other species and areas, and it has illustrated how spatially explicit demographic models can be combined with models predicting land-use change to help focus conservation priorities.

  10. Development tool for PHP programs

    OpenAIRE

    Karlsen, Håkon Skaarud

    2005-01-01

    This paper discusses how a PHP development toolbox can be implemented. One toolbox has been implemented, and the implementation is described and documented in the text. The toolbox is primarily meant to help students who are taking a System Development course (INF1050) at the University of Oslo with the implementation phase of a software engineering project, but other PHP programmers may also benefit from using the toolbox. It has been emphasized that the programming interface should be i...

  11. Idaho Nuclear Technology and Engineering Center Sodium-Bearing Waste Treatment Research and Development FY-2002 Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Herbst, Alan Keith; Deldebbio, John Anthony; Mc Cray, John Alan; Kirkham, Robert John; Olson, Lonnie Gene; Scholes, Bradley Adams

    2002-09-01

    The Idaho National Engineering and Environmental Laboratory (INEEL) is considering several optional processes for disposal of liquid sodium-bearing waste. During fiscal year 2002, immobilization-related research included of grout formulation development for sodium-bearing waste, absorption of the waste on silica gel, and off-gas system mercury collection and breakthrough using activated carbon. Experimental results indicate that sodium-bearing waste can be immobilized in grout at 70 weight percent and onto silica gel at 74 weight percent. Furthermore, a loading of 11 weight percent mercury in sulfur-impregnated activated carbon was achieved with 99.8% off-gas mercury removal efficiency.

  12. Development of a glass matrix for vitrification of sulphate bearing high level radioactive liquid waste

    International Nuclear Information System (INIS)

    Kaushik, C.P.; Mishra, R.K.; Thorat, Vidya; Ramchandran, M.; Amar Kumar; Ozarde, P.D.; Raj, Kanwar; Das, D.

    2004-07-01

    High level radioactive liquid waste (HLW) is generated during reprocessing of spent nuclear fuel. In the earlier reprocessing flow sheet ferrous sulphamate has been used for valancy adjustment of Pu from IV to III for effective separation. This has resulted in generation of HLW containing significance amount of sulphate. Internationally borosilicate glass matrix has been adopted for vitrification of HLW. The first Indian vitrification facility at Waste Immobilislition Plant (WIP), Tarapur a five component borosilicate matrix (SiO 2 :B 2 O 3 :Na 2 O : MnO : TiO 2 ) has been used for vitrification of waste. However at Trombay HLW contain significant amount of sulphate which is not compatible with standard borosilicate formulation. Extensive R and D efforts were made to develop a glass formulation which can accommodate sulphate and other constituents of HLW e.g., U, Al, Ca, etc. This report deals with development work of a glass formulations for immobilization of sulphate bearing waste. Different glass formulations were studied to evaluate the compatibility with respect to sulphate and other constituents as mentioned above. This includes sodium, lead and barium borosilicate glass matrices. Problems encountered in different glass matrices for containment of sulphate have also been addressed. A glass formulation based on barium borosilicate was found to be effective and compatible for sulphate bearing high level waste. (author)

  13. Accelerated leach test development program

    International Nuclear Information System (INIS)

    Fuhrmann, M.; Pietrzak, R.F.; Heiser, J.; Franz, E.M.; Colombo, P.

    1990-11-01

    In FY 1989, a draft accelerated leach test for solidified waste was written. Combined test conditions that accelerate leaching were validated through experimental and modeling efforts. A computer program was developed that calculates test results and models leaching mechanisms. This program allows the user to determine if diffusion controls leaching and, if this is the case, to make projections of releases. Leaching mechanisms other than diffusion (diffusion plus source term partitioning and solubility limited leaching) are included in the program is indicators of other processes that may control leaching. Leach test data are presented and modeling results are discussed for laboratory scale waste forms composed of portland cement containing sodium sulfate salt, portland cement containing incinerator ash, and vinyl ester-styrene containing sodium sulfate. 16 refs., 38 figs., 5 tabs

  14. Hydrodynamic bearings

    CERN Document Server

    Bonneau, Dominique; Souchet, Dominique

    2014-01-01

    This Series provides the necessary elements to the development and validation of numerical prediction models for hydrodynamic bearings. This book describes the rheological models and the equations of lubrication. It also presents the numerical approaches used to solve the above equations by finite differences, finite volumes and finite elements methods.

  15. Glucocorticoid programming of intrauterine development.

    Science.gov (United States)

    Fowden, A L; Valenzuela, O A; Vaughan, O R; Jellyman, J K; Forhead, A J

    2016-07-01

    Glucocorticoids (GCs) are important environmental and maturational signals during intrauterine development. Toward term, the maturational rise in fetal glucocorticoid receptor concentrations decreases fetal growth and induces differentiation of key tissues essential for neonatal survival. When cortisol levels rise earlier in gestation as a result of suboptimal conditions for fetal growth, the switch from tissue accretion to differentiation is initiated prematurely, which alters the phenotype that develops from the genotype inherited at conception. Although this improves the chances of survival should delivery occur, it also has functional consequences for the offspring long after birth. Glucocorticoids are, therefore, also programming signals that permanently alter tissue structure and function during intrauterine development to optimize offspring fitness. However, if the postnatal environmental conditions differ from those signaled in utero, the phenotypical outcome of early-life glucocorticoid receptor overexposure may become maladaptive and lead to physiological dysfunction in the adult. This review focuses on the role of GCs in developmental programming, primarily in farm species. It examines the factors influencing GC bioavailability in utero and the effects that GCs have on the development of fetal tissues and organ systems, both at term and earlier in gestation. It also discusses the windows of susceptibility to GC overexposure in early life together with the molecular mechanisms and long-term consequences of GC programming with particular emphasis on the cardiovascular, metabolic, and endocrine phenotype of the offspring. Copyright © 2016 Elsevier Inc. All rights reserved.

  16. X-ray fluorescence spectroscopy for the elemental analysis of plutonium-bearing materials for the materials disposition program

    International Nuclear Information System (INIS)

    Voit, S.L.; Boerigter, S.T.; Rising, T.L.

    1997-01-01

    The US Fissile Materials Disposition (MD) program will disposition about 50 MT of plutonium in the next century. Both of the alternative technologies for disposition, MOX Fuel and Immobilization require knowledge of the incoming composition to 1--5 wt%. Wavelength Dispersive X-Ray Fluorescence (WDXRF) systems, a common elemental analysis technology with a variety of industrial applications and commercial vendors, can readily achieve this level of characterization. Since much of the excess plutonium will be packaged in a long-term storage container as part of the DOE Environmental Management (DOE-EM) program to stabilize plutonium-bearing materials, the characterization system must be implemented during the packaging process. The authors describe a preliminary design for the integration of the WDXRF system into the packaging system to be used at the Rocky Flats site. The Plutonium Stabilization and Packaging System (PuSPS), coupled with the WDXRF characterization system will provide MD with stabilized plutonium-bearing excess material that can be more readily fed to an immobilization facility. The overall added expense to the MD program of obtaining analytical information after materials have been packaged in long-term storage containers could far exceed the expense of implementing XRF analysis during the packaging process

  17. Advanced Emissions Control Development Program

    Energy Technology Data Exchange (ETDEWEB)

    A.P.Evans; K.E. Redinger; M.J. Holmes

    1998-04-01

    The objective of the Advanced Emissions Control Development Program (AECDP) is to develop practical, cost-effective strategies for reducing the emissions of air toxics from coal-fired boilers. Ideally, the project aim is to effectively control air toxic emissions through the use of conventional flue gas cleanup equipment such as electrostatic precipitators (ESPS), fabric filters (baghouse), and wet flue gas desulfurization. Development work to date has concentrated on the capture of mercury, other trace metals, fine particulate and hydrogen chloride. Following the construction and evaluation of a representative air toxics test facility in Phase I, Phase II focused on the evaluation of mercury and several other air toxics emissions. The AECDP is jointly funded by the United States Department of Energy's Federal Energy Technology Center (DOE), the Ohio Coal Development Office within the Ohio Department of Development (oCDO), and Babcock& Wilcox-a McDermott company (B&W).

  18. Bearing restoration by grinding

    Science.gov (United States)

    Hanau, H.; Parker, R. J.; Zaretsky, E. V.; Chen, S. M.; Bull, H. L.

    1976-01-01

    A joint program was undertaken by the NASA Lewis Research Center and the Army Aviation Systems Command to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. No bearing failures occurred related to the restoration by grinding process. The risk and cost of a bearing restoration by grinding programs was analyzed. A microeconomic impact analysis was performed.

  19. Professional development and extension programs

    Energy Technology Data Exchange (ETDEWEB)

    Bereznai, G. [University of Ontario Institute of Technology, Oshawa, ON (Canada)

    2015-07-01

    Professional Development (PD) refers to the means by which people acquire, develop, maintain and enhance the specialist knowledge and skills needed to practice in their profession. Extension Programs (aka Continuing Education) are offered by most post-secondary degree/diploma/certificate granting institutions.The courses are typically taken on a part-time basis, and course delivery often includes distance learning technology. An important implementation of PD is via workplace training, industry specific seminars, workshops and non-credit courses offered by a wide range of service providers.

  20. Professional development and extension programs

    International Nuclear Information System (INIS)

    Bereznai, G.

    2015-01-01

    Professional Development (PD) refers to the means by which people acquire, develop, maintain and enhance the specialist knowledge and skills needed to practice in their profession. Extension Programs (aka Continuing Education) are offered by most post-secondary degree/diploma/certificate granting institutions.The courses are typically taken on a part-time basis, and course delivery often includes distance learning technology. An important implementation of PD is via workplace training, industry specific seminars, workshops and non-credit courses offered by a wide range of service providers.

  1. Wind Energy Career Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Gwen Andersen

    2012-03-29

    Saint Francis University has developed curriculum in engineering and in business that is meeting the needs of students and employers (Task 1) as well as integrating wind energy throughout the curriculum. Through a variety of approaches, the University engaged in public outreach and education that reached over 2,000 people annually (Task 2). We have demonstrated, through the success of these programs, that students are eager to prepare for emerging jobs in alternative energy, that employers are willing to assist in developing employees who understand the broader business and policy context of the industry, and that people want to learn about wind energy.

  2. Developing a successful robotics program.

    Science.gov (United States)

    Luthringer, Tyler; Aleksic, Ilija; Caire, Arthur; Albala, David M

    2012-01-01

    Advancements in the robotic surgical technology have revolutionized the standard of care for many surgical procedures. The purpose of this review is to evaluate the important considerations in developing a new robotics program at a given healthcare institution. Patients' interest in robotic-assisted surgery has and continues to grow because of improved outcomes and decreased periods of hospitalization. Resulting market forces have created a solid foundation for the implementation of robotic surgery into surgical practice. Given proper surgeon experience and an efficient system, robotic-assisted procedures have been cost comparable to open surgical alternatives. Surgeon training and experience is closely linked to the efficiency of a new robotics program. Formally trained robotic surgeons have better patient outcomes and shorter operative times. Training in robotics has shown no negative impact on patient outcomes or mentor learning curves. Individual economic factors of local healthcare settings must be evaluated when planning for a new robotics program. The high cost of the robotic surgical platform is best offset with a large surgical volume. A mature, experienced surgeon is integral to the success of a new robotics program.

  3. Strategic Employee Development (SED) Program

    Science.gov (United States)

    Nguyen, Johnny; Guevara (Castano), Nathalie; Thorpe, Barbara; Barnett, Rebecca

    2017-01-01

    As with many other U.S. agencies, succession planning is becoming a critical need for NASA. The primary drivers include (a) NASAs higher-than-average aged workforce with approximately 50 of employees eligible for retirement within 5 years; and (b) employees who need better developmental conversations to increase morale and retention. This problem is particularly concerning for Safety Mission Assurance (SMA) organizations since they traditionally rely on more experienced engineers and specialists to perform their organizations functions.In response to this challenge, the Kennedy Space Center (KSC) SMA organization created the Strategic Employee Development (SED) program. The SED programs goal is to provide a proactive method to counter the primary drivers by creating a deeper bench strength and providing a more comprehensive developmental feedback experience for the employee. The SED is a new succession planning framework that enables customization to any organization, and in this case, specifically for an SMA organization. This is accomplished via the identification of key positions, the corresponding critical competencies, and a process to help managers have relevant and meaningful development conversations with the workforce. As a result of the SED, several tools and products were created that allows management to make better strategic workforce decisions. Although there are opportunities for improvement for the SED program, the most important impact has been on the quality of developmental discussions for employees.

  4. Bearing system

    Science.gov (United States)

    Kapich, Davorin D.

    1987-01-01

    A bearing system includes backup bearings for supporting a rotating shaft upon failure of primary bearings. In the preferred embodiment, the backup bearings are rolling element bearings having their rolling elements disposed out of contact with their associated respective inner races during normal functioning of the primary bearings. Displacement detection sensors are provided for detecting displacement of the shaft upon failure of the primary bearings. Upon detection of the failure of the primary bearings, the rolling elements and inner races of the backup bearings are brought into mutual contact by axial displacement of the shaft.

  5. Program development fund: FY 1987

    Energy Technology Data Exchange (ETDEWEB)

    1989-03-01

    It is the objective of the Fund to encourage innovative research to maintain the Laboratory's position at the forefront of science. Funds are used to explore new ideas and concepts that may potentially develop into new directions of research for the Laboratory and that are consistent with the major needs, overall goals, and mission of the Laboratory and the DOE. The types of projects eligible for support from PDF include: work in forefront areas of science and technology for the primary purpose of enriching Laboratory research and development capabilities; advanced study of new hypotheses, new experimental concepts, or innovative approaches to energy problems; experiments directed toward ''proof of principle'' or early determination of the utility of a new concept; and conception, design analyses, and development of experimental devices, instruments, or components. This report is a review of these research programs.

  6. Program summary for the Civilian Reactor Development Program

    International Nuclear Information System (INIS)

    1982-07-01

    This Civilian Reactor Development Program document has the prime purpose of summarizing the technical programs supported by the FY 1983 budget request. This section provides a statement of the overall program objectives and a general program overview. Section II presents the technical programs in a format intended to show logical technical interrelationships, and does not necessarily follow the structure of the formal budget presentation. Section III presents the technical organization and management structure of the program

  7. Ambient Pressure Test Rig Developed for Testing Oil-Free Bearings in Alternate Gases and Variable Pressures

    Science.gov (United States)

    Bauman, Steven W.

    1990-01-01

    The Oil-Free Turbomachinery research team at the NASA Glenn Research Center is conducting research to develop turbomachinery systems that utilize high-speed, high temperature foil (air) bearings that do not require an oil lubrication system. Such systems combine the most advanced foil bearings from industry with NASA-developed hightemperature solid-lubricant technology. New applications are being pursued, such as Oil- Free turbochargers, auxiliary power units, and turbine propulsion systems for aircraft. An Oil-Free business jet engine, for example, would be simpler, lighter, more reliable, and less costly to purchase and maintain than current engines. Another application is NASA's Prometheus mission, where gas bearings will be required for the closed-cycle turbine based power-conversion system of a nuclear power generator for deep space. To support these applications, Glenn's Oil-Free Turbomachinery research team developed the Ambient Pressure Test Rig. Using this facility, researchers can load and heat a bearing and evaluate its performance with reduced air pressure to simulate high altitude conditions. For the nuclear application, the test chamber can be purged with gases such as helium to study foil gas bearing operation in working fluids other than air.

  8. Bears, Big and Little. Young Discovery Library Series.

    Science.gov (United States)

    Pfeffer, Pierre

    This book is written for children 5 through 10. Part of a series designed to develop their curiosity, fascinate them and educate them, this volume describes: (1) the eight species of bears, including black bear, brown bear, grizzly bear, spectacled bear, sun bear, sloth bear, polar bear, and giant panda; (2) geographical habitats of bears; (3)…

  9. Developing a career advancement program.

    Science.gov (United States)

    Pinette, Shirley L

    2003-01-01

    Have you ever asked yourself, "What will I be doing five or ten years from now?" "Will I be doing the same thing I'm doing right now?" How would you feel if the answer were "yes"? I often wonder if any of my employees think the same thing. If they do, and the answer is "yes," just how does that make them feel? A day's work for managers can run the gamut--from billing and coding, to patient issues, to staff performance reviews, to CQI, to JCAHO-just to name a few. We're NEVER bored. Can we say the same of our employees, or do they do the same thing day in and day out? If so, it's no wonder that attitudes may become negative and motivation and productivity may decline. What are we as healthcare managers and administrators doing to value and continually train our employees so that staff morale, productivity and patient satisfaction remain high? What are we doing to keep those highly motivated employees motivated and challenged so that they don't get bored and want to move across town to our neighboring hospital or healthcare center? What are we doing to stop our employees from developing the "same job, different day" attitude? A Career Ladder program holds many benefits and opportunities for the motivated employee who seeks and needs additional challenges on the job. It affords them opportunities to learn new skills, demonstrate initiative, accept additional responsibilities and possibly advance into new positions. It also affords them opportunities to grow, to be challenged and to feel like an important and valued member of the radiology team and radiology department. For the manager, a Career Ladder program affords opportunities to retain valuable employees, attract new high-quality employees and maintain a workforce of well-trained highly motivated employees, which in turn will provide high quality products and services to our customers. A Career Ladder program is a "win-win" situation for everyone. For the last twelve months, I have been working with other

  10. Government Risk-Bearing

    CERN Document Server

    1993-01-01

    The u.s. government bulks large in the nation's financial markets. The huge volume of government-issued and -sponsored debt affects the pricing and volume ofprivate debt and, consequently, resource allocation between competing alternatives. What is often not fully appreciated is the substantial influence the federal government wields overresource allocation through its provisionofcreditandrisk-bearing services to the private economy. Because peopleand firms generally seekto avoid risk, atsomeprice they are willing to pay another party to assume the risk they would otherwise face. Insurance companies are a class of private-sector firms one commonly thinks of as providing these services. As the federal government has expanded its presence in the U.S. economy during this century, it has increasingly developed programs aimed at bearing risks that the private sector either would not take on at any price, or would take on but atapricethoughtto besogreatthatmostpotentialbeneficiarieswouldnotpurchase the coverage. To...

  11. Development of internal CRD for next generation BWR-endurance and robustness tests of ball-bearing materials in high-pressure and high-temperature water

    International Nuclear Information System (INIS)

    Shoji Goto; Shuichi Ohmori; Michitsugu Mori; Shohei Kawano; Tadashi Narabayashi; Shinichi Ishizato

    2005-01-01

    An internal CRD using a heatproof ceramics insulated coil is under development to be a competitive and higher performance as Next- Generation BWR. In the case of the 1700MWe next generation BWR, adapting the internal CRDs, the reactor pressure vessel is almost equivalent to that of 1356 MWe ABWR. The endurance and robustness tests were examined in order to confirm the durability of the bearing for the internal CRD. The durability of the ball bearing for the internal CRD was performed in the high-pressure and high-temperature reactor water of current BWR conditions. The experimental results confirmed the durability of rotational numbers for the operation length of 60 years. We added the cruds into water to confirm the robustness of the ball bearing. The test results also showed good robustness even in high-density crud conditions, compared with the current BWR. This program is conducted as one of the selected offers for the advertised technical developments of the Institute of Applied Energy founded by METI (Ministry of Economy, Trade and Industry) of Japan. (authors)

  12. Development of a Ceramic Rolling Contact Bearing for High Temperature Use

    Science.gov (United States)

    1961-07-11

    operation) suspended in a gas stream was suprlied sufficient hardness, stability, and strength in through a tube in the bearing housing and was ex- an...and microfine MOS2, dried and screened, was supplied radial bearing mounting surfaces was less than to the bearing at an average rate of about 0.16...L.UBRICANT B ATMOSPHERE I".LlT TUBE DRILL TS5.ULAiT. INT. SEAL B TAP ONE KOLE I*G1-TEtMPjRAIUNE AS 45- TO SHEAR PIN SLOT FOR TTREAO END FLOW FOR HEATINM OP

  13. Development of a hybrid bearing using permanent magnets and piezoelectric actuators

    International Nuclear Information System (INIS)

    Park, Jung-Ho; Ham, Young-Bog; Yun, So-Nam; Lee, Hu-Seung

    2010-01-01

    In this study, a hybrid magnetic bearing with permanent magnets and piezoelectric actuators is investigated. First, in this study, a novel concept in which piezoelectric actuators are used to compensate for low stiffness and damping resulting from the unstable characteristics of a passive magnetic bearing using only permanent magnets is proposed. Secondly, the permanent magnets are optimally arranged through an electromagnetic field analysis. Then, the driving amplifier unit and a prototype radial bearing using the proposed concept are fabricated. Finally, basic characteristics, such as the results of an impact test and a rotational runout test with constant speed are investigated and discussed, and experiments using PID control method are conducted.

  14. Development of viable solutions for the synthesis of sulfur bearing single crystals

    Science.gov (United States)

    Lin, Xiao; Bud'ko, Sergey L.; Canfield, Paul C.

    2012-07-01

    The discovery of high temperature superconductivity in FeAs and FeSe based compounds has once again focused the condensed matter community on the need to systematically explore compounds containing chalcogens and pnictogens. Whereas some solution growth techniques have been developed to handle P and As, and Sb and Bi are versatile solvents in their own right, S has remained a problematic element to incorporate into conventional solution growth. To a large extent its low boiling point, combined with its polymeric nature in a molten state have made S an uninviting solvent. In this paper we present our development of a range of binary sulfur bearing solutions (some even sulfur rich) and demonstrate how we have been able to use these as useful starting points for the growth of a wide range of transition metal-sulfur-X ternary compounds. We present growth details and basic characterization data for Ni3Bi2S2, Co3Sn2S2, Fe2GeS4, CoSSb, and CePd3S4. In addition we present a remarkably simple method for the growth of single crystalline Co with crystallization taking place below the Curie temperature.

  15. Development and application of an antibody-based protein microarray to assess physiological stress in grizzly bears (Ursus arctos).

    Science.gov (United States)

    Carlson, Ruth I; Cattet, Marc R L; Sarauer, Bryan L; Nielsen, Scott E; Boulanger, John; Stenhouse, Gordon B; Janz, David M

    2016-01-01

    A novel antibody-based protein microarray was developed that simultaneously determines expression of 31 stress-associated proteins in skin samples collected from free-ranging grizzly bears (Ursus arctos) in Alberta, Canada. The microarray determines proteins belonging to four broad functional categories associated with stress physiology: hypothalamic-pituitary-adrenal axis proteins, apoptosis/cell cycle proteins, cellular stress/proteotoxicity proteins and oxidative stress/inflammation proteins. Small skin samples (50-100 mg) were collected from captured bears using biopsy punches. Proteins were isolated and labelled with fluorescent dyes, with labelled protein homogenates loaded onto microarrays to hybridize with antibodies. Relative protein expression was determined by comparison with a pooled standard skin sample. The assay was sensitive, requiring 80 µg of protein per sample to be run in triplicate on the microarray. Intra-array and inter-array coefficients of variation for individual proteins were generally bears. This suggests that remotely delivered biopsy darts could be used in future sampling. Using generalized linear mixed models, certain proteins within each functional category demonstrated altered expression with respect to differences in year, season, geographical sampling location within Alberta and bear biological parameters, suggesting that these general variables may influence expression of specific proteins in the microarray. Our goal is to apply the protein microarray as a conservation physiology tool that can detect, evaluate and monitor physiological stress in grizzly bears and other species at risk over time in response to environmental change.

  16. Development of aerodynamic bearing support for application in air cycle machines

    Directory of Open Access Journals (Sweden)

    Šimek J.

    2014-06-01

    Full Text Available Air cycle machines (ACM are used in environmental control system of aircrafts to manage pressurization of the cabin. The aim of this work is to gain theoretical and experimental data enabling replacement of rolling bearings, which require lubrication and have limited operating speed, with aerodynamic bearing support. Aerodynamic bearings do not pollute process air and at the same time allow achieving higher operating speed, thus enabling to reduce machine mass and dimensions. A test stand enabling the verification of aerodynamic bearing support properties for prospective ACM was designed, manufactured and tested with operating speeds up to 65 000 rpm. Some interesting features of the test stand design and the test results are presented. A smaller test stand with operating speed up to 100 000 rpm is in design stage.

  17. Plutonium-bearing materials feed report for the DOE Fissile Materials Disposition Program alternatives

    International Nuclear Information System (INIS)

    Brough, W.G.; Boerigter, S.T.

    1995-01-01

    This report has identified all plutonium currently excess to DOE Defense Programs under current planning assumptions. A number of material categories win clearly fan within the scope of the MD (Materials Disposition) program, but the fate of the other categories are unknown at the present time. MD planning requires that estimates be made of those materials likely to be considered for disposition actions so that bounding cases for the PEIS (Programmatic Environmental Impact Statement) can be determined and so that processing which may be required can be identified in considering the various alternatives. A systematic analysis of the various alternatives in reachmg the preferred alternative requires an understanding of the possible range of values which may be taken by the various categories of feed materials. One table identifies the current total inventories excess to Defense Program planning needs and represents the bounding total of Pu which may become part of the MD disposition effort for all materials, except site return weapons. The other categories, principally irradiated fuel, rich scrap, and lean scrap, are discussed. Another table summarizes the ranges and expected quantities of Pu which could become the responsibility of the MD program. These values are to be used for assessing the impact of the various alternatives and for scaling operations to assess PEIS impact. Determination of the actual materials to be included in the disposition program will be done later

  18. Latest Development and Application of Nb-Bearing High Strength Pipeline Steels

    Science.gov (United States)

    Zhang, Yongqing; Shang, Chengjia; Guo, Aimin; Zheng, Lei; Niu, Tao; Han, Xiulin

    In order to solve the pollution problem emerging in China recently, China's central government is making great efforts to raise the percentage of natural gas consumption in the China's primary energy mix, which needs to construct big pipelines to transport natural gas from the nation's resource-rich western regions to the energy-starved east, as well as import from the Central Asia and Russia. With this mainstream trend, high strength, high toughness, heavy gauge, and large diameter pipeline steels are needed to improve the transportation efficiency. This paper describes the latest progresses in Nb-bearing high strength pipeline steels with regard to metallurgical design, development and application, including X80 coil with a thickness up to 22.0mm, X80 plate with a diameter as much as 1422mm, X80 plate with low-temperature requirements and low-Mn sour service X65 for harsh sour service environments. Moreover, based on widely accepted TMCP and HTP practices with low carbon and Nb micro-alloying design, this paper also investigated some new metallurgical phenomena based on powerful rolling mills and heavy ACC equipment.

  19. Development of a multichemical food web model: application to PBDEs in Lake Ellasjoen, Bear Island, Norway.

    Science.gov (United States)

    Gandhi, Nilima; Bhavsar, Satyendra P; Gewurtz, Sarah B; Diamond, Miriam L; Evenset, Anita; Christensen, Guttorm N; Gregor, Dennis

    2006-08-01

    A multichemical food web model has been developed to estimate the biomagnification of interconverting chemicals in aquatic food webs. We extended a fugacity-based food web model for single chemicals to account for reversible and irreversible biotransformation among a parent chemical and transformation products, by simultaneously solving mass balance equations of the chemicals using a matrix solution. The model can be applied to any number of chemicals and organisms or taxonomic groups in a food web. The model was illustratively applied to four PBDE congeners, BDE-47, -99, -100, and -153, in the food web of Lake Ellasjøen, Bear Island, Norway. In Ellasjøen arctic char (Salvelinus alpinus), the multichemical model estimated PBDE biotransformation from higher to lower brominated congeners and improved the correspondence between estimated and measured concentrations in comparison to estimates from the single-chemical food web model. The underestimation of BDE-47, even after considering bioformation due to biotransformation of the otherthree congeners, suggests its formation from additional biotransformation pathways not considered in this application. The model estimates approximate values for congener-specific biotransformation half-lives of 5.7,0.8,1.14, and 0.45 years for BDE-47, -99, -100, and -153, respectively, in large arctic char (S. alpinus) of Lake Ellasjøen.

  20. Grizzly bears and mining in the Cheviot region

    Energy Technology Data Exchange (ETDEWEB)

    Symbaluk, M.; Archibald, T. [Foothills Research Inst., Hinton, AB (Canada)

    2008-07-01

    This presentation described a grizzly bear research program conducted by the Foothill Research Institute at the Cheviot mine. The research program uses a satellite land classification protocol and remote sensing tools to map and identify the grizzly bear habitat. Modelling is also conducted to predict bear probabilities. Global information systems (GIS) are used to evaluate bear responses to human activities. Grizzly bear health and wellness is also assessed as part of the programs. Land maps are combined with global positioning systems (GPS) and resource selection function (RSF) models in order to map grizzly bear distribution. Data obtained from the program is used to inform decision-making and support policy development. Previous studies predicted that the grizzly bear population would disappear from the Cheviot mine area after 20 years of its being in operation. The research program provided real data to test predictions made during previous environmental assessments. Grizzly bear populations have actually increased in the mining area. It was concluded that the bears have moved more freely through industrial landscapes than previously predicted. tabs., figs.

  1. Muzzling the Bear: Gorbachev’s Program to Restructure the Soviet Military

    Science.gov (United States)

    1990-04-01

    quantity to quality- in a continuing program of military accumulation.4 4 Steven Adragna argues thalt Soviet military doctrine can not evolve until it...aggressive nature and intent of capitalist society. Adragna maintains that so far there has been no serious effort to discredit the historical theorem that...any military action the Soviet Union takes is defensive in nature by definition and is therefore justified. Further, Adragna claims that the Kremlin’s

  2. Development of an aerostatic bearing system for roll-to-roll printed electronics

    Science.gov (United States)

    Chen, Shasha; Chen, Weihai; Liu, Jingmeng; Chen, Wenjie; Jin, Yan

    2018-06-01

    Roll-to-roll printed electronics is proved to be an effective way to fabricate electrical devices on various substrates. High precision overlay alignment plays a key role to create multi-layer electrical devices. Multiple rollers are adopted to support and transport the substrate web. In order to eliminate the negative effect of the machining error and assembling error of the roller, a whole roll-to-roll system including two aerostatic bearing devices with arrayed restrictors is proposed in this paper. Different to the conventional roller, the aerostatic bearing device can create a layer of air film between the web and the device to realize non-contact support and transport. Based on simplified Navier–Stokes equations, the theoretical model of the air film is established. Moreover, the pressure distribution of the whole flow field and single restrictor in different positions are modeled by conducting numerical simulation with computational fluid dynamics (CFD) software FLUENT. The load capacity curves and stiffness curves are generated to provide guidance for optimizing the structure of the device. A prototype of the aerostatic bearing system is set up and the experiment tests are carried out. For the proposed aerostatic bearing roller with a diameter of 100 mm and length of 200 mm, the experimental results show the aerostatic bearing method can achieve the position accuracy in a range of 1 μm in the vertical direction of the web, which is much better than that using existing methods.

  3. Foil Bearing Coating Behavior in CO2

    Energy Technology Data Exchange (ETDEWEB)

    Walker, Matthew [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Kruizenga, Alan Michael [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Pasch, James Jay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Fleming, Darryn [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-08-01

    The Sandia S-CO2 Recompression Closed Brayton Cycle (RCBC) utilizes a series of gas foil bearings in its turbine-alternator-compressors. At high shaft rotational speed these bearings allow the shaft to ride on a cushion of air. Conversely, during startup and shutdown, the shaft rides along the foil bearing surface. Low-friction coatings are used on bearing surfaces in order to facilitate rotation during these periods. An experimental program was initiated to elucidate the behavior of coated bearing foils in the harsh environments of this system. A test configuration was developed enabling long duration exposure tests, followed by a range of analyses relevant to their performance in a bearing. This report provides a detailed overview of this work. The results contained herein provide valuable information in selecting appropriate coatings for more advanced future bearing-rig tests at the newly established test facility in Sandia-NM.

  4. Qualification of high damping seismic isolation bearings for the ALMR

    International Nuclear Information System (INIS)

    Tajirian, F.F.; Gluekler, E.L.; Chen, W.P.; Kelly, J.M.

    1992-01-01

    The Advanced Liquid Metal Reactor (ALMR) seismic isolation system consists of high damping steel-laminated elastomeric bearings. This type of bearing is used worldwide to isolate buildings and large critical components. A comprehensive testing program has been developed to qualify the use of this system for the ALMR. The program includes material characterization tests, various scale bearing tests, full-size bearing tests, shake table tests, and long-term aging tests. The main tasks and objectives of this program are described in the paper. Additionally, a detailed assessment of completed ALMR bearing test results will be provided. This assessment will be mainly based on half-scale bearing tests performed at the Earthquake Engineering Research Center (EERC) of the University of California at Berkeley and at the Energy Technology Engineering Center (ETEC). These tests were funded by the U.S. Department of Energy (DOE). Both static and dynamic tests were performed. Bearings with two types of end connections were tested: dowelled and bolted. The parameters examined will include the vertical, horizontal stiffness and damping of the bearings under different loading conditions up to failure. This will determine the available margins in the bearings above the design vertical load and horizontal displacement. Additionally, the self-centering capability of the bearings after an earthquake will be addressed. On the basis of these findings, recommendations can be made if necessary, to improve current manufacturing procedures, quality control, and procurement specifications. (author)

  5. Programs and Research Advisor | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Support risk management of regional programming and partnerships by: ... analysing, on a regular basis, key program development and performance indicators; ... Represent the IDRC and Regional Director at key events in order to gather ...

  6. Bearing surfaces in total hip replacements: state of the art and future developments.

    Science.gov (United States)

    McKellop, H A

    2001-01-01

    Because the UHMWPE components fabricated by the historic process of gamma-sterilization in air are no longer marketed, a surgeon who wishes to continue performing joint replacement surgery must choose among the new polyethylenes, or he or she may choose a modern metal-metal or ceramic-ceramic bearing, each of which has its potential advantages and disadvantages (Table 4). Ultimately, it is the responsibility of the surgeon to assess the risk-benefit ratios of each of the new bearing combinations and make an informed and wise choice among them.

  7. Development of a container for the transportation and storage of plutonium bearing materials

    International Nuclear Information System (INIS)

    Ammerman, D.; Geinitz, R.; Thorp, D.; Rivera, M.

    1998-03-01

    There is a large backlog of plutonium contaminated materials at the Rocky Flats Environmental Technology Site near Denver, Colorado, USA. The clean-up of this site requires this material to be packaged in such a way as to allow for efficient transportation to other sites or to a permanent geologic repository. Prior to off-site shipment of the material, it may be stored on-site for a period of time. For this reason, it is desirable to have a container capable of meeting the requirements for storage as well as the requirements for transportation. Most of the off-site transportation is envisioned to take place using the TRUPACT-II Type B package, with the Waste Isolation Pilot Plant (WIPP) as the destination. Prior to the development of this new container, the TRUPACT-II had a limit of 325 FGE (fissile gram equivalents) of plutonium due to criticality control concerns. Because of the relatively high plutonium content in the material to be transported, transporting 325 FGE per TRUPACT-II is uneconomical. Thus, the purpose of the new containers is to provide criticality control to increase the allowed TRUPACT-II payload and to provide a safe method for on-site storage prior to transport. This paper will describe the analysis and testing used to demonstrate that the Pipe Overpack Container provides safe on-site storage of plutonium bearing materials in unhardened buildings and provides criticality control during transportation within the TRUPACT-II. Analyses included worst-case criticality analyses, analyses of fork-lift time impacts, and analyses of roof structure collapse onto the container. Testing included dynamic crush tests, bare pipe impact tests, a 30-minute totally engulfing pool-fire test, and multiple package impact tests in end-on and side-on orientations

  8. Development of a clinically relevant impingement test method for a mobile bearing lumbar total disc replacement.

    Science.gov (United States)

    Siskey, Ryan; Peck, Jonathan; Mehta, Hitesh; Kosydar, Allison; Kurtz, Steven; Hill, Genevieve

    2016-09-01

    Total disc arthroplasty is an alternative therapy to spinal fusion for the treatment of neck or low back pain and is hypothesized to reduce the risk of disease progression to the adjacent spinal levels. Radiographic and retrieval analyses of various total disc replacements (TDRs) have shown evidence of impingement damage. Impingement of TDRs can occur when the device reaches the limits of its functional range of motion, causing contact between peripheral regions of the device. Impingement can be associated with increased wear and mechanical damage; however, impingement conditions are not simulated in current standardized mechanical bench test methods. This study explored the test conditions necessary to apply clinically relevant impingement loading to a lumbar TDR in vitro. An experimental protocol was developed and evaluated using in vivo retrievals for qualitative and quantitative validation. Retrieval analysis was conducted on a set of 11 size 3 retrieved Charité devices using American Society for Testing and Materials F561 as a guide. The impingement range of motion was determined using a combination of modeling and experiments, and was used as an input in vitro testing. A 1-million cycle in vitro test was then conducted, and the in vitro samples were characterized using methods similar to the retreived devices. All in vitro tested samples exhibited impingement regions and damage patterns consistent with retrieved devices. Consistent with the retrievals, the impingement damage on the rim was a combination of abrasive wear and plastic deformation. Micro computed tomography (microCT) was used to quantitatively assess rim damage due to impingement. Rim penetration was statistically lower in the retrievals when compared with both in vitro groups. Rim elongation was comparable among all groups. The simulated-facet group had statistically greater angular rim deformations than the retrieval group and the no-facet group. Results demonstrate that clinically relevant

  9. Achievement report for fiscal 1998. Research and development of nano-structural materials for ceramic bearing application (the second year); 1998 nendo seika hokokusho. Ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Development is made on ceramic bearing using high-performance and low-cost nano-structural materials, and its application is performed to high-quality bearings suitable for energy conservation in automobiles and industrial machines, and bearings for office automation devices, electronics, and aeronautic and maritime development. To achieve these goals, raw material synthesizing technologies, forming technologies, structural control technologies, processing technologies and mass production technologies shall be established. Fiscal 1998 had the following achievements: establishment of nano-structure controlled ceramic material powder synthesizing technology (nano-lamination type composite powder made by using the beads mill co-precipitation method, nano-lamination type composite powder made by using the New Mymill co-precipitation method, nano-lamination type composite powder made by using the controlled liquid phase method, composite nano-structured gel, and nano-powder synthesis); near net forming technology for spherical ceramics; high-speed processing technology for ultra smooth surface; evaluation of rolling fatigue properties of ceramic bearings; and analysis and evaluation of nano-structured materials. Since this alumina-based ceramic bearing can be produced at reduced cost with performance comparable to silicon nitride based bearing, investigations and discussions are being given on the application thereof. (NEDO)

  10. Development of superconducting magnetic bearing using superconducting coil and bulk superconductor

    Energy Technology Data Exchange (ETDEWEB)

    Seino, H; Nagashima, K; Arai, Y [Railway Technical Research Institute, Hikari-cho 2-8-38, Kokubunji-shi, Tokyo (Japan)], E-mail: seino@rtri.or.jp

    2008-02-01

    The authors conducted a study on superconducting magnetic bearing, which consists of superconducting rotor and stator to apply the flywheel energy-storage system for railways. In this study, high temperature bulk superconductor (HTS bulk) was combined with superconducting coils to increase the load capacity of the bearing. In the first step of the study, the thrust rolling bearing was selected for application by using liquid nitrogen cooled HTS bulk. 60mm-diameter HTS bulks and superconducting coil which generated a high gradient of magnetic field by cusp field were adopted as a rotor and a stator for superconducting magnetic bearing, respectively. The results of the static load test and the rotation test, creep of the electromagnetic forces caused by static flux penetration and AC loss due to eccentric rotation were decreased to the level without any problems in substantial use by using two HTS bulks. In the result of verification of static load capacity, levitation force (thrust load) of 8900N or more was supportable, and stable static load capacity was obtainable when weight of 460kg was levitated.

  11. Development of superconducting magnetic bearing using superconducting coil and bulk superconductor

    International Nuclear Information System (INIS)

    Seino, H; Nagashima, K; Arai, Y

    2008-01-01

    The authors conducted a study on superconducting magnetic bearing, which consists of superconducting rotor and stator to apply the flywheel energy-storage system for railways. In this study, high temperature bulk superconductor (HTS bulk) was combined with superconducting coils to increase the load capacity of the bearing. In the first step of the study, the thrust rolling bearing was selected for application by using liquid nitrogen cooled HTS bulk. 60mm-diameter HTS bulks and superconducting coil which generated a high gradient of magnetic field by cusp field were adopted as a rotor and a stator for superconducting magnetic bearing, respectively. The results of the static load test and the rotation test, creep of the electromagnetic forces caused by static flux penetration and AC loss due to eccentric rotation were decreased to the level without any problems in substantial use by using two HTS bulks. In the result of verification of static load capacity, levitation force (thrust load) of 8900N or more was supportable, and stable static load capacity was obtainable when weight of 460kg was levitated

  12. Site-wide remedial alternative development in Bear Creek Valley, Oak Ridge Reservation

    International Nuclear Information System (INIS)

    Anderson, M.

    1995-07-01

    This paper presents a case study of an environmental restoration project at a major mixed waste site that poses unique challenges to remediation efforts. Bear Creek Valley is located immediately west of the Y-12 Plant on the Oak Ridge Reservation (ORR) in Oak Ridge, Tennessee. The Y-12 Plant was built in 1943 as part of the Manhattan Project, with its original mission being electromagnetic separation of uranium. Since being completed, the Y-12 Plant has also been used for chemical processing of uranium and lithium compounds as well as precision fabrication of components containing these and other materials. Wastes containing radionuclides, metals, chlorinated solvents, oils, coolants, polychlorinated biphenyis (PCBs), and others were disposed of in large quantities at Bear Creek Valley as a result of manufacturing operations at the Y-12 Plant. The Bear Creek Valley feasibility study is using innovative strategies to efficiently and thoroughly consider the information available regarding Bear Creek Valley and process options that could be combined into its remedial alternatives

  13. Interactive development of object handling programs

    Energy Technology Data Exchange (ETDEWEB)

    Gini, G C; Gini, M L

    1982-01-01

    The authors describe work on development of a software system for writing and testing programs for a computer controlled manipulation. The authors examine in particular how the development of working programs is facilitated by the use of an interactive system based on an interpreter. The paper presents the main features of Pointy the system developed at Stanford Artificial Intelligence Laboratory as a tool for writing assembly programs. The user, interacting with the manipulator, constructs an incremental model of the objects involved in the assembly and develops the corresponding symbolic program. 13 references.

  14. Protease-Sensitive Liposomes in Chemotherapy & Chemoradiotherapy: From Material Development to In Vivo Application in Tumor-Bearing Mice

    DEFF Research Database (Denmark)

    Brogaard, Rikke Yding; Melander, Fredrik

    to enhance therapeutic efficacies. In this thesis, the development, characterization, and evaluation of an advanced liposomal DDS and its potential in chemoradiotherapy is presented from material development to in vivo application in tumor*bearing mice. In the first part of the thesis, we report the design...... concept of the liposomal DDS, which leads to rapid cellular uptake. Various lipid compositions are tested in uptake and cytotoxicity experiments in vitro, followed by in vivo experiments where the ability of the liposomal DDS to accumulate in tumors together with its anti*cancer activity is explored...... in tumor*bearing mice. The in vivo data demonstrates superior anti*cancer activity relative to the free drug and to conventional, long circulating liposomes. This indicates that the MMP*sensitive liposomal DDS holds potential in therapeutic applications. In the second part of the thesis, the potential...

  15. Contemporary flowstone development links early hominin bearing cave deposits in South Africa

    Science.gov (United States)

    Pickering, Robyn; Kramers, Jan D.; Hancox, Philip John; de Ruiter, Darryl J.; Woodhead, Jon D.

    2011-06-01

    The Cradle of Humankind cave sites in South Africa preserve fossil evidence of four early hominin taxa: Australopithecus africanus, Australopithecus sediba, Paranthropus robustus and early Homo. In order to integrate this record into a pan-African scenario of human evolutionary history it is critical to have reliable dates and temporal ranges for the southern African hominins. In the past a lack of precise and accurate chronological data has prevented the evaluation of the temporal relationships between the various sites. Here we report new uranium-lead (U-Pb) radiometric ages obtained from sheets of calcium carbonate flowstone inter-bedded between clastic cave sediments at the site of Swartkrans, providing bracketing ages for the fossiliferous deposits. The fossil bearing units of Swartkrans, specifically the Hanging Remnant and Lower Bank of Member 1, are underlain by flowstone layers dated to 2.25 ± 0.05 Ma and 2.25 ± 0.08 Ma and capped by layers of 1.8 ± 0.01 Ma and 1.7 ± 0.07 Ma. The age bracket of the Member 1 deposits is therefore between 2.31 and 1.64 Ma. However, by combining the U-Pb with biostratigraphic data we suggest that this can be narrowed down to between 1.9 and 1.8 Ma. These data can be compared with other recently dated sites and a radiometrically dated U-Pb age sequence formed: Sterkfontein Member 4, Swartkrans Member 1, Malapa, and Cooper's D. From this new U-Pb dataset, a pattern of contemporary flowstone development emerges, with different caves recording the same flowstone-forming event. Specifically overlapping flowstone formation takes place at Swartkrans and Sterkfontein at ~ 2.29 Ma and ~ 1.77 Ma, and at Sterkfontein and Malapa at ˜ 2.02 Ma. This suggests a regional control over the nature and timing of speleothem development in cave deposits and these flowstone layers could assist in future correlation, both internal to specific deposits and regionally between sites.

  16. Ethical Development through Student Activities Programming.

    Science.gov (United States)

    Brock, Carol S.

    1991-01-01

    Student activities programing, viewed as essential to the college experience, is defended by outlining some of the values and growth opportunities it provides for students. Several specific programing strategies useful as catalysts in values development are described, including values clarification exercises, multicultural programing, and…

  17. A methodology for developing distributed programs

    NARCIS (Netherlands)

    Ramesh, S.; Mehndiratta, S.L.

    1987-01-01

    A methodology, different from the existing ones, for constructing distributed programs is presented. It is based on the well-known idea of developing distributed programs via synchronous and centralized programs. The distinguishing features of the methodology are: 1) specification include process

  18. National investment programs and sustainable development

    OpenAIRE

    Szyja, Paulina

    2014-01-01

    In situation of economic crisis many countries, for example the United States, members of European Union prepared anti-crisis programs to conduct investments. In most cases, they concentrated on modernization of transport or energy infrastructure. In Poland it would have been presented program "Polish Investments". The main purposes of the article is presentation of public investments programs and their role in sustainable development.

  19. Innovative Technology Development Program. Final summary report

    International Nuclear Information System (INIS)

    Beller, J.

    1995-08-01

    Through the Office of Technology Development (OTD), the U.S. Department of Energy (DOE) has initiated a national applied research, development, demonstration, testing, and evaluation program, whose goal has been to resolve the major technical issues and rapidly advance technologies for environmental restoration and waste management. The Innovative Technology Development (ITD) Program was established as a part of the DOE, Research, Development, Demonstration, Testing, and Evaluation (RDDT ampersand E) Program. The plan is part of the DOE's program to restore sites impacted by weapons production and to upgrade future waste management operations. On July 10, 1990, DOE issued a Program Research and Development Announcement (PRDA) through the Idaho Operations Office to solicit private sector help in developing innovative technologies to support DOE's clean-up goals. This report presents summaries of each of the seven projects, which developed and tested the technologies proposed by the seven private contractors selected through the PRDA process

  20. Journal bearing

    Science.gov (United States)

    Menke, John R.; Boeker, Gilbert F.

    1976-05-11

    1. An improved journal bearing comprising in combination a non-rotatable cylindrical bearing member having a first bearing surface, a rotatable cylindrical bearing member having a confronting second bearing surface having a plurality of bearing elements, a source of lubricant adjacent said bearing elements for supplying lubricant thereto, each bearing element consisting of a pair of elongated relatively shallowly depressed surfaces lying in a cylindrical surface co-axial with the non-depressed surface and diverging from one another in the direction of rotation and obliquely arranged with respect to the axis of rotation of said rotatable member to cause a flow of lubricant longitudinally along said depressed surfaces from their distal ends toward their proximal ends as said bearing members are rotated relative to one another, each depressed surface subtending a radial angle of less than 360.degree., and means for rotating said rotatable bearing member to cause the lubricant to flow across and along said depressed surfaces, the flow of lubricant being impeded by the non-depressed portions of said second bearing surface to cause an increase in the lubricant pressure.

  1. Automotive Stirling Engine Development Program

    Science.gov (United States)

    Nightingale, N.; Ernst, W.; Richey, A.; Simetkosky, M.; Smith, G.; Antonelli, M. (Editor)

    1983-01-01

    Mod I engine testing and test results, the test of a Mod I engine in the United States, Mod I engine characterization and analysis, Mod I Transient Test Bed fuel economy, Mod I-A engine performance are discussed. Stirling engine reference engine manufacturing and reduced size studies, components and subsystems, and the study and test of low-cost casting alloys are also covered. The overall program philosophy is outlined, and data and results are presented.

  2. Development of new engine bearings with overlay consisting of solid lubricants; Kotai junkatsu overlay tsuki engine yo suberi jikuuke zairyo no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Kanayama, H; Kawakami, S; Gohara, C [Taiho Kogyo Co. Ltd., Aichi (Japan); Fuwa, Y; Michioka, H [Toyota Motor Corp., Aichi (Japan)

    1997-10-01

    Recently, modern engines have a tendency for higher output and longer periods. As a result , higher bearing performance is required. For this reason, we have developed the new conceptual overlay consisting of solid lubricants and thermosetting plastics. This paper describes the performance of engine bearings with the new overlay. 5 refs., 13 figs., 5 tabs.

  3. Calculation methods for steadily loaded, off-set pivot, tilting pad thrust bearings. (Guide to use of computer program A9235.)

    Science.gov (United States)

    1992-12-01

    ESDU 92035 provides details of a FORTRAN program that implements the calculation method of ESDU 83004. It allows performance analysis of an existing design, or the design of a bearing dimensions, subject to any space constraint, are recommended. The predicted performance includes the lubricant film thickness under load, its temperature and flow rate, the power loss, and the bearing temperature. Recommendations are also made on surface finish. Warning messages are output in the following cases, for each of which possible remedial actions are suggested: drain or pad temperature too high, churning losses too great, film thickness too small, pad number too high, ratio or inner to outer pad radius too large, flow rate too great, lubricant or pad temperature outside usable range. A lubricant database is provided that may be extended or edited. The program applies to Newtonian lubricants in laminar flow. Worked examples illustrate the use of the program.

  4. Developing Program Management Leadership for Acquisition Reform

    Science.gov (United States)

    2011-04-30

    mêçÅÉÉÇáåÖë= çÑ=íÜÉ= bfdeqe=^kkr^i=^`nrfpfqflk== obpb^o`e=pvjmlpfrj== qeropa^v=pbppflkp== slirjb ff Developing Program Management Leadership for...4. TITLE AND SUBTITLE Developing Program Management Leadership for Acquisition Reform 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...Developing Program  Management   Leadership   for Acquisition Reform    The 8th Annual Acquisition Research Symposium Panel #20: Investing in People

  5. Developments in the treatment of solid alpha-bearing wastes at the PNC plutonium fuel facilities

    International Nuclear Information System (INIS)

    Ohtsuka, K.; Miyo, H.; Ohuchi, J.; Shiga, K.; Muto, T.

    1978-01-01

    Some results of experiments done in PNC are presented on volume reduction technics for alpha-bearing wastes. A pilot wood milling machine automatically mills the plywood frames of nipple connected HEPA filters, which result in fine sized wooden chips, two nipples and the filter components. The filter components are melted in an induction furnace to be homogeneous solids. These methods and incineration of wooden chips reduce the stored volume of HEPA filters to 1/50 -- 1/100. PVC and neoprene rubber are decomposed in concentrated sulfuric acid, followed by oxidation with nitric acid. The acid digestion process generates chlorine-rich gas, from which only chlorine is selectively absorbed in water. An alpha-bearing vessel and a glovebox are cut at their installed places without spread of plutonium contamination outside the greenhouses. (auth.)

  6. Coastal nonpoint pollution control program: Program development and approval guidance

    International Nuclear Information System (INIS)

    1993-01-01

    The document, developed by NOAA and EPA, contains guidance for states in developing and implementing their coastal nonpoint pollutant source programs. It describes the requirements that must be met, including: the geographic scope of the program; the pollutant sources to be addressed; the types of management measures used; the establishment of critical areas; technical assistance, public participation, and administrative coordination; and, the process for program submission and Federal approval. The document also contains the criteria by which NOAA and EPA will review the states' submissions

  7. Automotive Stirling engine development program: A success

    Science.gov (United States)

    Tabata, W. K.

    1987-01-01

    The original 5-yr Automotive Stirling Engine Development Program has been extended to 10 years due to reduced annual funding levels. With an estimated completion date of April 1988, the technical achievements and the prospectives of meeting the original program objectives are reviewed. Various other applications of this developed Stirling engine technology are also discussed.

  8. The DUPIC fuel development program in KAERI

    Energy Technology Data Exchange (ETDEWEB)

    Yang, M S; Park, H S [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1997-07-01

    This study describes the DUPIC fuel development program in KAERI as follows; Burning spent PWR fuel again in CANDU by DUPIC, Compatibility with existing CANDU system, Feasibility of DUPIC fuel fabrication, Waste reduction, Safeguard ability, Economics of DUPIC fuel cycle, The DUPIC fuel development program, and International prospective. 5 refs., 10 figs.

  9. Developing a mentoring program in clinical nutrition.

    Science.gov (United States)

    Martindale, Robert G; McClave, Stephen; Heyland, Daren; August, David

    2010-01-01

    Mentoring programs in nutrition are essential to the survival of clinical nutrition as we know it today. The best method known to maintain an influx of talent to a discipline is by developing an active mentoring program. This paper describes 1 concept for development of a viable mentor program. Mentoring should be flexible and based on mentees' training background. Realistic goals should be set, with written and verbal feedback, to sustain a successful program. Programs should incorporate the Socratic Method whenever possible. Factors that leave doubt about the survival of nutrition as a viable area of focus for physicians include the inability to generate adequate funds to support oneself and limited numbers of mentors available with dedicated time to be a mentor. A healthy, sustainable mentoring program in clinical nutrition will ensure survival of physician-based nutrition programs.

  10. Nuclear Power Infrastructure Development Program: Korean Education Program

    International Nuclear Information System (INIS)

    Choi, Sung Yeol; Hwang, Il Soon; Kim, Si Hwan

    2009-01-01

    Many countries have decided nuclear power for next energy resources as one of the long-term energy supply options. IAEA projected nuclear power expansion up to 2030 reaching between 447 GWe and 691 GWe compared to 370 GWe and 2660 TWh at the end of 2006. Both low and high projection is accompanied with new nuclear power plant constructions respectively 178 and 357, about 11 units per year, and most new construction is in North America, the Far East, Eastern Europe, the Middle East, and Southeast Asia. During the last forty years, thirty three countries have established commercial nuclear power programs but only some of them have developed comprehensive and large scale peaceful nuclear power infrastructure. Although various cooperation and guidance program of nuclear power infrastructure, developing appropriate environment and infrastructure of nuclear power plant is still challenging problems for developing countries launching nuclear power program. With increasing the demand of safety and safeguard from international society, creating appropriate infrastructure becomes essential requirements in national nuclear power program. In the viewpoint of developing countries, without sufficient explanation and proper guidance, infrastructure could be seen only as another barrier in its nuclear power program. The importance of infrastructure development would be obscured by ostensible business and infrastructure program can result in increasing entering barriers to peaceful nuclear power application field without benefits to developing countries and international community. To avoid this situation by providing enough explanation and realistic case example and cooperate with the countries wanting to establish comprehensive nuclear power infrastructure in the peaceful applications, we are creating the education program of infrastructure development with basic guidelines of the IAEA infrastructure series and Korean experiences from least developed country to advanced country

  11. Monitoring and mitigating measures to reduce potential impacts of oil and gas exploration and development on bears in the Inuvik region

    Energy Technology Data Exchange (ETDEWEB)

    Branigan, M. [Government of the Northwest Territories, Inuvik, NT (Canada). Dept. of Environment and Natural Resources

    2007-07-01

    The Inuvik Region consists of the Northwest Territories portion of the Inuvialuit Settlement Region and the Gwich'in Settlement Area. The range of grizzly bears, polar bears and black bears extends to different parts of the region. The potential impact of development depends on the season of the development and the species of bear found in the footprint. As such, monitoring and mitigation measures should take this into consideration. This presentation focused on the potential impacts and current practices to monitor and mitigate the impacts in the region. Mitigation measures currently used include: communication with stakeholders; waste management guidelines; use of wildlife monitors to identify key habitat and den sites and to deter bears; minimum flight altitudes; and safety training. Suggestions for additional mitigation measures were also presented. figs.

  12. Program Development Tools and Infrastructures

    International Nuclear Information System (INIS)

    Schulz, M.

    2012-01-01

    Exascale class machines will exhibit a new level of complexity: they will feature an unprecedented number of cores and threads, will most likely be heterogeneous and deeply hierarchical, and offer a range of new hardware techniques (such as speculative threading, transactional memory, programmable prefetching, and programmable accelerators), which all have to be utilized for an application to realize the full potential of the machine. Additionally, users will be faced with less memory per core, fixed total power budgets, and sharply reduced MTBFs. At the same time, it is expected that the complexity of applications will rise sharply for exascale systems, both to implement new science possible at exascale and to exploit the new hardware features necessary to achieve exascale performance. This is particularly true for many of the NNSA codes, which are large and often highly complex integrated simulation codes that push the limits of everything in the system including language features. To overcome these limitations and to enable users to reach exascale performance, users will expect a new generation of tools that address the bottlenecks of exascale machines, that work seamlessly with the (set of) programming models on the target machines, that scale with the machine, that provide automatic analysis capabilities, and that are flexible and modular enough to overcome the complexities and changing demands of the exascale architectures. Further, any tool must be robust enough to handle the complexity of large integrated codes while keeping the user's learning curve low. With the ASC program, in particular the CSSE (Computational Systems and Software Engineering) and CCE (Common Compute Environment) projects, we are working towards a new generation of tools that fulfill these requirements and that provide our users as well as the larger HPC community with the necessary tools, techniques, and methodologies required to make exascale performance a reality.

  13. Program Development Tools and Infrastructures

    Energy Technology Data Exchange (ETDEWEB)

    Schulz, M

    2012-03-12

    Exascale class machines will exhibit a new level of complexity: they will feature an unprecedented number of cores and threads, will most likely be heterogeneous and deeply hierarchical, and offer a range of new hardware techniques (such as speculative threading, transactional memory, programmable prefetching, and programmable accelerators), which all have to be utilized for an application to realize the full potential of the machine. Additionally, users will be faced with less memory per core, fixed total power budgets, and sharply reduced MTBFs. At the same time, it is expected that the complexity of applications will rise sharply for exascale systems, both to implement new science possible at exascale and to exploit the new hardware features necessary to achieve exascale performance. This is particularly true for many of the NNSA codes, which are large and often highly complex integrated simulation codes that push the limits of everything in the system including language features. To overcome these limitations and to enable users to reach exascale performance, users will expect a new generation of tools that address the bottlenecks of exascale machines, that work seamlessly with the (set of) programming models on the target machines, that scale with the machine, that provide automatic analysis capabilities, and that are flexible and modular enough to overcome the complexities and changing demands of the exascale architectures. Further, any tool must be robust enough to handle the complexity of large integrated codes while keeping the user's learning curve low. With the ASC program, in particular the CSSE (Computational Systems and Software Engineering) and CCE (Common Compute Environment) projects, we are working towards a new generation of tools that fulfill these requirements and that provide our users as well as the larger HPC community with the necessary tools, techniques, and methodologies required to make exascale performance a reality.

  14. Yugoslavian Petroleum Refinery development program

    International Nuclear Information System (INIS)

    Ocic, Ozren

    1999-01-01

    This paper shows the analysis of the world petroleum industry development, being an important factor in planning the development of the Yugoslav petroleum industry and Pancevo Petroleum Refinery, as well. Then Yugoslav petroleum industry development is analysed, including the appropriate balances of crude oil production and crude oil products consumption. The way of realizing the basic targets are also proposed. Likewise, the analysis of the condition within West European refineries has been conducted, from the aspects of technology, energy consumption and environmental protection and the same analysis for Pancevo Petroleum Refinery has been presented, too. The analysis of the condition within the refineries in the European Union countries and comparing it with the condition within Pancevo Petroleum Refinery, makes it mainly possible to recognize the development programmes which should be realized in order that Pancevo Petroleum Refinery could reach the refining level of the EU countries. (Original)

  15. Analogy Mapping Development for Learning Programming

    Science.gov (United States)

    Sukamto, R. A.; Prabawa, H. W.; Kurniawati, S.

    2017-02-01

    Programming skill is an important skill for computer science students, whereas nowadays, there many computer science students are lack of skills and information technology knowledges in Indonesia. This is contrary with the implementation of the ASEAN Economic Community (AEC) since the end of 2015 which is the qualified worker needed. This study provided an effort for nailing programming skills by mapping program code to visual analogies as learning media. The developed media was based on state machine and compiler principle and was implemented in C programming language. The state of every basic condition in programming were successful determined as analogy visualization.

  16. GAS BEARING

    Science.gov (United States)

    Skarstrom, C.W.

    1960-09-01

    A gas lubricated bearing for a rotating shaft is described. The assembly comprises a stationary collar having an annular member resiliently supported thereon. The collar and annular member are provided with cooperating gas passages arranged for admission of pressurized gas which supports and lubricates a bearing block fixed to the rotatable shaft. The resilient means for the annular member support the latter against movement away from the bearing block when the assembly is in operation.

  17. Development, implementation and operational experience with 900 mm R1T pocket-type bearings at Oskarshamn unit 3 nuclear steam turbine generator

    International Nuclear Information System (INIS)

    Peel, P.; Roos, A.

    2015-01-01

    The Oskarshamn unit 3 nuclear steam turbine generator in Sweden is operated by OKG and, following the extensive PULS upgrade project, delivers an increased rated output of 1450 MW making it the most powerful BWR unit worldwide. Several turbine bearing incidents occurred in 2009 and 2010, which initiated a detailed root cause analysis to determine the reasons and propose appropriate mitigation measures to ensure reliable unit operation. Together with OKG, ALSTOM Power implemented a short-term solution to operate the unit over the winter period of 2010-11. Subsequently, during the annual outage in June 2011, a permanent solution involving a R1T pocket-type bearing design was installed at three shaft-line positions. Since the 1980's, R1T bearings with diameters from 250 to 670 mm have been operating in numerous full-speed (3000/3600 rpm) steam turbine generators. However, this was the first application of a R1T bearing developed at a diameter of 900 mm and for half-speed operation. This paper presents an overview of the bearing development and details the successful operational feedback gathered to date on the three installed bearings. In comparison with the three tilting pad bearing design, which has typically been used on large half-speed ALSTOM Power steam turbine generators to date, it confirms the R1T bearing design as a viable alternative. (authors)

  18. New developments in employee assistance programs.

    Science.gov (United States)

    White, R K; McDuff, D R; Schwartz, R P; Tiegel, S A; Judge, C P

    1996-04-01

    Employee assistance programs have developed from alcoholism assessment and referral centers to specialized behavioral health programs. Comprehensive employee assistance programs are defined by six major components: identification of problems based on job performance, consultation with supervisors, constructive confrontation, evaluation and referral, liaison with treatment providers, and substance abuse expertise. Other services have been added as enhancements to the basic model and include managed behavioral health activities and professional assistance committees, which provide services for impaired professionals and executives. Recent developments in the field are illustrated through examples from the experience of the employee assistance program at the University of Maryland Medical System in Baltimore.

  19. Grizzly bear

    Science.gov (United States)

    Schwartz, C.C.; Miller, S.D.; Haroldson, M.A.; Feldhamer, G.; Thompson, B.; Chapman, J.

    2003-01-01

    The grizzly bear inspires fear, awe, and respect in humans to a degree unmatched by any other North American wild mammal. Like other bear species, it can inflict serious injury and death on humans and sometimes does. Unlike the polar bear (Ursus maritimus) of the sparsely inhabited northern arctic, however, grizzly bears still live in areas visited by crowds of people, where presence of the grizzly remains physically real and emotionally dominant. A hike in the wilderness that includes grizzly bears is different from a stroll in a forest from which grizzly bears have been purged; nighttime conversations around the campfire and dreams in the tent reflect the presence of the great bear. Contributing to the aura of the grizzly bear is the mixture of myth and reality about its ferocity. unpredictable disposition, large size, strength, huge canines, long claws, keen senses, swiftness, and playfulness. They share characteristics with humans such as generalist life history strategies. extended periods of maternal care, and omnivorous diets. These factors capture the human imagination in ways distinct from other North American mammals. Precontact Native American legends reflected the same fascination with the grizzly bear as modern stories and legends (Rockwell 1991).

  20. Simplified Casing Program for Development Wells in Mahu Well Block

    Directory of Open Access Journals (Sweden)

    Lu Zongyu

    2017-01-01

    Full Text Available In the Mahu well block of Junggar basin, the complex formation has many sets of pressure system. Especially, the formation with microcracks in the middle layer is loose and the pressure bearing capacity is low. Lost circulation is prone to occur in this layer. At present, high investment and long drilling period were the main problems in the exploration and development process. The geostress 3D model of Mahu well block was established by means of logging and drilling data. The model provided the three-pressure profiles of Mahu well block for casing program optimization and safety drilling. Each well could be optimized the intermediate casing setting position. The intermediate casing was saved 160 meters long. The total of drilling speed was improved 5 times compared with the past drilling process. Slim hole drilling technology raised ROP 51.96% higher, and the average drilling period is shorten to 24.83 days.

  1. Development of Y-Ba-Cu-O Superconductors for Magnetic Bearings

    Science.gov (United States)

    Selvamanickam, V.; Pfaffenbach, K.; Sokolowski, R. S.; Zhang, Y.; Salama, K.

    1996-01-01

    The material requirements, material manufacturing and magnetic properties that are relevant to fabrication of High Temperature Superconductor (HTS) magnetic bearings have been discussed. It is found that the seeded-melt-texturing method can be used to fabricate the single domain material that is required to achieve the best magnetic properties. Trapped-field mapping has been used as a non-destructive tool to determine the single-domain nature of the HTS material and quantity of the HTS disks. Both the trapped field and the levitation force of the Y-Ba-Cu-O disks are found to be strongly sensitive to the oxygen content.

  2. Journal bearing impedance descriptions for rotordynamic applications

    NARCIS (Netherlands)

    Childs, D.W.; Moes, H.; Leeuwen, van H.J.

    1977-01-01

    Bearing impedance vectors are introduced for plain journal bearings which define the bearing reaction force components as a function of the bearing motion. Impedance descriptions are developed directly for the approximate Ocvirk (short) and Sommerfeld (long) bearing solutions. The impedance vector

  3. Developing the Metropolia Alumni Relations Program

    OpenAIRE

    Hardy, Tea

    2015-01-01

    The target of this Master's Thesis was to create a practical plan to further develop the alumni relations program at Helsinki Metropolia University of Applied Sciences. The plan will act as a guide for the program on how to reach and engage Metropolia's students and alumni in order to create a sustainable and active alumni relations program. Special attention was given to the international students and alumni, which is an understandable approach from the global perspective as many of the Metr...

  4. Assessing a GTA professional development program

    OpenAIRE

    Alicea-Muñoz, Emily; Masip, Joan Espar; Sullivan, Carol Subiño; Schatz, Michael F.

    2018-01-01

    For the last four years, the School of Physics at Georgia Tech have been preparing new Graduate Teaching Assistants (GTAs) through a program that integrates pedagogy, physics content, and professional development strategies. Here we discuss various assessments we have used to evaluate the program, among them surveys, GTA self-reporting, and end-of-semester student evaluations. Our results indicate that GTAs who participate in the program find its practical activities useful, feel better prepa...

  5. Ultrashort pulsed laser technology development program

    Science.gov (United States)

    Manke, Gerald C.

    2014-10-01

    The Department of Navy has been pursuing a technology development program for advanced, all-fiber, Ultra Short Pulsed Laser (USPL) systems via Small Business Innovative Research (SBIR) programs. Multiple topics have been published to promote and fund research that encompasses every critical component of a standard USPL system and enable the demonstration of mJ/pulse class systems with an all fiber architecture. This presentation will summarize published topics and funded programs.

  6. Alloy development for irradiation performance: program strategy

    International Nuclear Information System (INIS)

    Bloom, E.E.; Stiegler, J.O.; Wiffen, F.W.; Dalder, E.N.C.; Reuther, T.C.; Gold, R.E.; Holmes, J.J.; Kummer, D.L.; Nolfi, F.V.

    1978-01-01

    The objective of the Alloy Development for Irradiation Performance Program is the development of structural materials for use in the first wall and blanket region of fusion reactors. The goal of the program is a material that will survive an exposure of 40 MWyr/m 2 at a temperature which will allow use of a liquid-H 2 O heat transport system. Although the ultimate aim of the program is development of materials for commercial reactors by the end of this century, activities are organized to provide materials data for the relatively low performance interim machines that will precede commercial reactors

  7. Development of education programs using HANARO

    International Nuclear Information System (INIS)

    Ser, K. W.; Cho, H. J.; Won, J. Y.; Ju, Y. C.; Lee, H. Y.; Choi, Y. M.

    2001-01-01

    The purposes of the study is to development of the education program using HANARO, which is one of the programs for HANARO Utilization. These consist of four fields; radioisotope production application, neutron activation analysis, examination of irradiated fuel/material and neutron beam application. This program provides various special research courses to faculties, researchers, universities and the industrial sector. In the development of the education program using HANARO, we have plan to the graduate thesis research course for the students, such a plan identifies the actual and potential capabilities of the reactor as well as its current and potential future specialists. Also, we have designed the development of actual training and education programs on radiological emergency preparedness, its necessary to the on-site and off-side public health and safety around near the reactor and relation facilities. These course topics involve the introduction of radiological emergency, actual technical method on radiation measurement, radiological emergency exercise and so on

  8. R+D works for the further development of high temperature reactors. Development and testing of a pilot blower with magnetic bearings. Phase 1 - plans ready for construction. Phase 2 - construction and testing

    International Nuclear Information System (INIS)

    1991-01-01

    The development of helium compressors in magnetic bearings as cooling blowers for HTR's made a considerable contribution to the extension of Germany's technical potential. Magnetic bearings open up new possibilities with simultaneous savings due to the reduction in friction and wear. With the use of active magnetic bearings for cooling gas blowers any potential contamination of the primary circuit by oil is completely excluded. The oil system is omitted and therefore so are a large number of safety requirements and technical layout conditions. The keywords here are: safe inclusion of radio-activity, fire and explosion protection, omission of oil plant spatially separated but necessarily close to the blowers and the reactor, omission of removal of used bearing oil from the primary area. One would expect that the dynamic rotor properties of blower shafts with magnetic bearings are better than those with oil bearings, as bearing damping can be provided in the region of critical speeds. (orig./GL) [de

  9. Examining Burma's Development: A Research Fellowship Program ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    The Regional Center for Social Science and Sustainable Development (RCSD) at Thailand's Chiang Mai University will manage the four-year program, which targets junior and mid-level academic and non-academic Burmese scholars. The program will ... LVIF announces five more funded projects. Eleven world-class ...

  10. Nutritional programming of reproductive development in heifers

    Science.gov (United States)

    Developmental programming is the biological process by which environmental factors influence the development of the organs and tissues in the body. There are two areas of developmental programming being investigated with applicability to beef production systems to improve performance of replacement...

  11. Assessing an Academic Library Professional Development Program

    Science.gov (United States)

    Harker, Karen R.; O'Toole, Erin; Sassen, Catherine

    2018-01-01

    Professional development programs have been established in many academic libraries to support the research and scholarly activities of librarians. Continuous assessment can contribute to the sustainability and effectiveness of these programs. This study describes how measures of need, participation, satisfaction, and impact were employed to assess…

  12. Emotionally Handicapped Pupils: Developing Appropriate Educational Programs.

    Science.gov (United States)

    North Carolina State Dept. of Public Instruction, Raleigh. Div. for Exceptional Children.

    The document is designed to assist local school systems as they plan, develop, and improve programs for emotionally handicapped students. Sections cover the following areas: definition of emotionally handicapped students; pre-planninq for emotionally handicapped programs; identification, referral, screening, assessment, and placement; service…

  13. The US Liquid Metal Reactor Development Program

    International Nuclear Information System (INIS)

    Till, C.E.; Arnold, W.H.; Griffith, J.D.

    1988-01-01

    The US Liquid Metal Reactor Development Program has been restructured to take advantage of the opportunity today to carry out R and D on truly advanced reactor technology. The program gives particular emphasis to improvements to reactor safety. The new directions are based on the technology of the Integral Fast Reactor (IFR). Much of the basis for superior safety performance using IFR technology has been experimentally verified and aggressive programs continue in EBR-II and TREAT. Progress has been made in demonstrating both the metallic fuel and the new electrochemical processes of the IFR. The FFTF facility is converting to metallic fuel; however, FFTF also maintains a considerable US program in oxide fuels. In addition, generic programs are continuing in steam generator testing, materials development, and, with international cooperation, aqueous reprocessing. Design studies are carried out in conjunction with the IFR technology development program. In summary, the US maintains an active development program in Liquid Metal Reactor technology, and new directions in reactor safety are central to the program

  14. Polar bears at risk

    Energy Technology Data Exchange (ETDEWEB)

    Norris, S.; Rosentrater, L.; Eid, P.M. [WWF International Arctic Programme, Oslo (Norway)

    2002-05-01

    rains also destroy the denning habitat of ringed seals, the polar bears' primary prey. Declines in the ringed seal population would mean a loss of food for polar bears. A trend toward stronger winds and increasing ice drift observed in some parts of the Arctic over the last five decades will likely increase energy expenditures and stress levels in polar bears that spend most of their lives on drifting sea ice. Polar bears face other limiting factors as well. Historically, the main threat to polar bears has been hunting. Satisfactory monitoring information has been obtained for most polar bear populations in recent years, however there is concern about hunting in areas without formal quota systems, such as Greenland. A range of toxic pollutants, including heavy metals, radioactivity, and persistent organic pollutants (POPs) are found throughout the Arctic. Of greatest concern are the effects of POPs on polar bears, which include a general weakening of the immune system, reduced reproductive success and physical deformities. The expansion of oil development in the Arctic poses additional threats; for example, disturbances to denning females in the Arctic National Wildlife Refuge in Alaska could undermine recruitment of the Beaufort Sea polar bear population. These threats, along with other effects of human activity in the Arctic, combine to pressure polar bears and their habitat. Large carnivores are sensitive indicators of ecosystem health and can be used to define the minimum area necessary to preserve intact ecosystems. WWF has identified the polar bear as a unique symbol of the complexities and interdependencies of the arctic marine ecosystem as it works toward its goal of preserving biodiversity for future generations.

  15. Development and validation of a weight-bearing finite element model for total knee replacement.

    Science.gov (United States)

    Woiczinski, M; Steinbrück, A; Weber, P; Müller, P E; Jansson, V; Schröder, Ch

    2016-01-01

    Total knee arthroplasty (TKA) is a successful procedure for osteoarthritis. However, some patients (19%) do have pain after surgery. A finite element model was developed based on boundary conditions of a knee rig. A 3D-model of an anatomical full leg was generated from magnetic resonance image data and a total knee prosthesis was implanted without patella resurfacing. In the finite element model, a restarting procedure was programmed in order to hold the ground reaction force constant with an adapted quadriceps muscle force during a squat from 20° to 105° of flexion. Knee rig experimental data were used to validate the numerical model in the patellofemoral and femorotibial joint. Furthermore, sensitivity analyses of Young's modulus of the patella cartilage, posterior cruciate ligament (PCL) stiffness, and patella tendon origin were performed. Pearson's correlations for retropatellar contact area, pressure, patella flexion, and femorotibial ap-movement were near to 1. Lowest root mean square error for retropatellar pressure, patella flexion, and femorotibial ap-movement were found for the baseline model setup with Young's modulus of 5 MPa for patella cartilage, a downscaled PCL stiffness of 25% compared to the literature given value and an anatomical origin of the patella tendon. The results of the conducted finite element model are comparable with the experimental results. Therefore, the finite element model developed in this study can be used for further clinical investigations and will help to better understand the clinical aspects after TKA with an unresurfaced patella.

  16. Metra operations management development program : 2010 - 2015.

    Science.gov (United States)

    2016-11-04

    On behalf of the Urban Transportation Center, the University of Illinois (UIC) Great Cities Institute (GCI) provided curriculum development and training services to Metra for a workforce education program targeted to new and experienced managers. Met...

  17. Devolving Programs (2009) | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2016-04-25

    Apr 25, 2016 ... ... senior management requested that past experience with devolution ... The primary objective of this evaluation is to develop guiding principles that could inform future devolution practice. ... External Program Reviews (2015).

  18. Programs | IDRC - International Development Research Centre

    International Development Research Centre (IDRC) Digital Library (Canada)

    Our development programs support innovative solutions that improve global ... Chestnut farm worker carries basket of harvest chestnuts on shoulders in China ... Invest in knowledge and innovation for large-scale positive change; Build the ...

  19. Development of the French Photovoltaic Program

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, M.

    1980-07-01

    The French photovoltaic research program is reviewed, listing companies involved. Projections of module and system costs are discussed. French industrial experience in photovoltaics is reviewed and several French systems operating in developing countries are mentioned. (MHR)

  20. Defense Nanotechnology Research and Development Program

    National Research Council Canada - National Science Library

    2007-01-01

    ...), Army Research Office (ARO) and the Air Force Office of Scientific Research (AFOSR)initiated numerous research and development programs focusing on advancing science and technology below one micron in size...

  1. Orthopaedic measurements with computed radiography: Methodological development, accuracy, and radiation dose with special reference to the weight-bearing lower extremity and the dislocating patella

    International Nuclear Information System (INIS)

    Sanfridsson, J.

    2001-01-01

    The overall aim of this study was to develop and evaluate a measurement system for computed radiography and Picture Archiving and Communication Systems, permitting measurements of long distances and angles in and between related images. The developed measurement system, which was based on the QUESTOR Precision Radiography system, was applied to the weight-bearing knee with special reference to the dislocating patella. The QPR system modified for CR fulfilled the criteria for measuring the weight-bearing knee. The special measuring assistance tools that were developed were important for the implementation of CR and PACS, particularly in workstations programmed for musculoskeletal radiology. The energy imparted to the patient was reduced by 98% at the lowest exposure of the CR-system, compared with our conventional analogue method, without loss of diagnostic accuracy. The CR technique creates a possibility, to an extent not previously feasible, to differentiate the exposure parameters (and thus minimise the radiation dose to the patient) by carefully considering the purpose of the examination. A radiographic method for measuring the rotation of the femur and the tibia, and the patellar translation was developed and applied to healthy volunteers. The introduced patellar variables have yielded new insights into the complex sequence of motions between the femur, tibia, and patella. The patients with a dislocating patella were subdivided into one 'clean' group of spontaneous dislocations and one group with various traumas in the history, which thus resulted in two groups with distinct radiographic differences. The Q-angle was decreased in knees that had suffered dislocations, and the traditional surgical treatment with a further reduction of the Q-angle must be challenged. The use of clinical measurements of the Q-angle was not an optimal way to evaluate the mechanical alignment in the patellofemoral joint under physiological conditions. In this study, we have proved

  2. A work-for-food enrichment program increases exploration and decreases stereotypies in four species of bears.

    Science.gov (United States)

    Wagman, Jason D; Lukas, Kristen E; Dennis, Patricia M; Willis, Mark A; Carroscia, Joe; Gindlesperger, Curt; Schook, Mandi W

    2018-01-01

    Zoo-housed bears are prone to exhibiting stereotypic behaviors, generally considered indicators of negative welfare. We explored the effects of a variable-time feeding enrichment schedule on behavioral indicators of welfare in four bear species at Cleveland Metroparks Zoo. We distributed the diets of eight bears in one of five enrichment items, for two consecutive days each, and monitored behavior throughout the day. In Experiment 1, we compared variable-time to fixed-time presentation of enrichment over two, 10-day periods. Overall, bears performed more exploratory behavior when enriched (p enrichment was associated with a greater increase in exploratory behavior than fixed-time enrichment when compared to baseline (p enrichment were also associated with similar decreases in abnormal behavior compared to baseline. For Experiment 2, we tested habituation to enrichment over 30 days using multiple items and a semi-variable presentation schedule. Again during the enrichment period, bears exhibited increased exploratory behavior (p enrichment period for these behaviors. Collectively, these results suggest that daily, variable-schedule feeding enrichment, with intermittent presentation of unique enrichment items, increases behavioral indicators of positive welfare and decreases behavioral indicators of negative welfare. © 2018 Wiley Periodicals, Inc.

  3. Development of a Decommissioning Certificate Program; TOPICAL

    International Nuclear Information System (INIS)

    M. R. Morton

    1999-01-01

    A Decommissioning Certificate Program has been developed at Washington State University Tri-Cities (WSU TC) in conjunction with Bechtel Hanford, Inc. (BHI), and the U.S. Department of Energy (DOE)to address the increasing need for qualified professionals to direct and manage decommissioning projects. The cooperative effort between academia, industry, and government in the development and delivery of this Program of education and training is described, as well as the Program's design to prepare students to contribute sooner, and at a higher level, to decommissioning projects

  4. Development of a Decommissioning Certificate Program

    International Nuclear Information System (INIS)

    Morton, M. R.

    1999-01-01

    A Decommissioning Certificate Program has been developed at Washington State University Tri-Cities (WSU TC) in conjunction with Bechtel Hanford, Inc. (BHI), and the U.S. Department of Energy (DOE)to address the increasing need for qualified professionals to direct and manage decommissioning projects. The cooperative effort between academia, industry, and government in the development and delivery of this Program of education and training is described, as well as the Program's design to prepare students to contribute sooner, and at a higher level, to decommissioning projects

  5. John Anderson's development of (situational) realism and its bearing on psychology today.

    Science.gov (United States)

    Hibberd, Fiona J

    2009-10-01

    In 1927, the Scottish philosopher John Anderson arrived in Australia to take up the chair of Philosophy at the University of Sydney. By the late 1930s, the "macrostructure" of his realist system was in place. It includes a theory of process and a substantial metaphysics, one that opposes positivism, linguistic philosophy and all forms of idealism. However, beyond Australia it remains largely unknown, despite its bearing on a number of current issues in psychology and the social sciences generally. This article outlines Anderson's transition from Hegelian idealism to realism, describes aspects of his ontology and epistemology, compares some of Anderson's ideas with Dewey's pragmatism and explains their relevance to present-day psychology.

  6. Roller bearing geometry design

    Science.gov (United States)

    Savage, M.; Pinkston, B. H. W.

    1976-01-01

    A theory of kinematic stabilization of rolling cylinders is extended and applied to the design of cylindrical roller bearings. The kinematic stabilization mechanism puts a reverse skew into the rolling elements by changing the roller taper. Twelve basic bearing modification designs are identified amd modeled. Four have single transverse convex curvature in their rollers while eight have rollers which have compound transverse curvature made up of a central cylindrical band surrounded by symmetric bands with slope and transverse curvature. The bearing designs are modeled for restoring torque per unit axial displacement, contact stress capacity, and contact area including dynamic loading, misalignment sensitivity and roller proportion. Design programs are available which size the single transverse curvature roller designs for a series of roller slopes and load separations and which design the compound roller bearings for a series of slopes and transverse radii of curvature. The compound rollers are proportioned to have equal contact stresses and minimum size. Design examples are also given.

  7. Advancing CANDU technology AECL's Development program

    International Nuclear Information System (INIS)

    Torgerson, D.F.

    1997-01-01

    AECL has a comprehensive product development program that is advancing all aspects of CANDU technology including fuel and fuel cycles, fuel channels, heavy water and tritium technology, safety technology, components and systems, constructability, health and environment, and control and instrumentation. The technology arising from these programs is being incorporated into the CANDU design through an evolutionary process. This evolutionary process is focused on improving economics, enhancing safety and ensuring fuel cycle flexibility to secure fuel supply for the foreseeable future. This strategic thrusts are being used by CANDU designers and researchers to set priorities and goals for AECL's development activities. The goals are part of a 25-year development program that culminates in the 'CANDU X'. The 'CANDU X' is not a specific design - it is a concept that articulates our best extrapolation of what is achievable with the CANDU design over the next 25 years, and includes the advanced features arising from the R and D and engineering to be done over that time. AECL's current product, the 700 MWe class CANDU 6 and the 900 MWe class CANDU 9, both incorporate output from the development programs as the technology become available. A brief description of each development areas is given below. The paper ends with the conclusion that AECL has a clear vision of how CANDU technology and products will evolve over the next several years, and has structured a comprehensive development program to take full advantage of the inherent characteristics of heavy water reactors. (author)

  8. University role in nuclear power program in developing countries

    International Nuclear Information System (INIS)

    Notea, A.

    1977-01-01

    The academic education in nuclear engineering should be considered as a subsystem within the general nuclear program of the country as well as within the educational structure of the university. The academic trained personnel are of major importance as future participants in decisional and planning steps of the program. Hence, the ''production'' of academic manpower in this field should be started at the earliest steps. The nuclear engineering curriculum should be planned in accordance with the objectives stated by the power program and the challenges foreseen. Obviously, the objectives in a developing country are considerably different from those of developed countries highly advanced in the nuclear power field. The paper analyzes possible objectives in a developing country which intends to implement nuclear power program. In view of these objectives curricula planning for the undergraduate and graduate levels are presented and explained. The courses for undergraduates intend to provide basic information to relatively large numbers of students from various faculties, as they are expected to join the program at various constructional stages. Major emphasise is given to graduates as they will act in the cadre of senior engineers and officials of the country. The research works for theses in developed countries may be highly technical, dealing with crumbs of huge development project carried out on national or international level. Such research works are hardly justified in countries not involved in the project. In developing countries the problems to be confronted with are mainly licensing and siting and to much less extent nuclear power technology. Hence the choice of subjects for theses should be coherent with these directions. Obviously, the subjects are bound to the department manpower and budgetary limitations. As a demonstration two fields were analysed under our local constraints and objectives. Subjects suitable for theses are pointed out. The fields dealt

  9. Commercial radioactive waste minimization program development guidance

    International Nuclear Information System (INIS)

    Fischer, D.K.

    1991-01-01

    This document is one of two prepared by the EG ampersand G Idaho, Inc., Waste Management Technical Support Program Group, National Low-Level Waste Management Program Unit. One of several Department of Energy responsibilities stated in the Amendments Act of 1985 is to provide technical assistance to compact regions Host States, and nonmember States (to the extent provided in appropriations acts) in establishing waste minimization program plans. Technical assistance includes, among other things, the development of technical guidelines for volume reduction options. Pursuant to this defined responsibility, the Department of Energy (through EG ampersand G Idaho, Inc.) has prepared this report, which includes guidance on defining a program, State/compact commission participation, and waste minimization program plans

  10. Developments in the photonics program at OSC

    Science.gov (United States)

    Peyghambarian, N.

    2014-10-01

    The photonics program at the College of Optical Sciences started nearly 30 years ago. In 1984, the program was focused on development of femtosecond laser sources and their use in investigating semiconductor carrier dynamics. The program grew into polymer and organic optics in late 1989 and was strengthened by the winning of the CAMP MURI from ONR in 1995 that was focused on multifunctional polymers including photorefractive polymers, organic light emitting diodes and 3D direct laser writing. Also in 1995, the areas of glass waveguide and fiber optic materials and devices were added to the program. In 2008, the optical communication and future internet research was started through winning the CIAN NSF ERC. Expertise in thin films, optical storage and the fundamental aspects of light are elements of the overall research program. Holographic 3D display, autofocus lenses, bio-medical imaging and devices for vision have also been ongoing research areas.

  11. Development of the Alberta Diagnostic Reading Program.

    Science.gov (United States)

    Horvath, Frank G.; Machura, Shirley

    The development of the Alberta Diagnostic Reading Program (ADRP) was based on a current psycholinguistic theory that describes reading as a process in which the reader uses background information to communicate with the author. To ensure its usefulness and effectiveness, the developers of the ADRP sought the advice and direct involvement of many…

  12. Fred P. Ellison and Portuguese Program Development

    Science.gov (United States)

    Milleret, Margo

    2016-01-01

    The written record of Ellison's involvement in Portuguese program development begins in 1964 when he became chairman of the Portuguese Language Development Group that met at several Modern Language Association meetings before being accepted by the American Association of Teachers of Spanish and Portuguese (AATSP) in 1967. The record ends in the…

  13. Developing a Multicultural Library Media Program.

    Science.gov (United States)

    Houff, Suzanne G.

    1994-01-01

    Describes the development of a multicultural library media program based on experiences at a Virginia middle school. Highlights include the media center as a cultural and curricular resource; establishing philosophies and goals; reviewing current materials and establishing guidelines for new material selection; staff development; and an integrated…

  14. Human-Wildlife Conflict and Environmental Education: Evaluating a Community Program to Protect the Andean Bear in Ecuador

    Science.gov (United States)

    Espinosa, Santiago; Jacobson, Susan K.

    2012-01-01

    Environmental education is a widespread, yet relatively unexamined strategy to reduce human-wildlife conflicts. We evaluated knowledge, attitudes and behavioral intentions toward bear conservation after five years of environmental education in a Quichua community. Conflicts with livestock predation created mixed attitudes and behaviors toward bear…

  15. Development of a training assurance program

    International Nuclear Information System (INIS)

    Palchinsky, J.; Waylett, W.J. Jr.

    1987-01-01

    The nuclear industry has made a significant commitment to improve training through the implementation of accredited performance-based training programs. Senior management expects that human performance will improve as a result of significant resource allocations. How do they know if training is effective in achieving improved human performance? Florida Power and Light Company is developing a Training Assurance Program to track indicators of training performance and future trends. Integrating the company's Quality Improvement Program processes with systematic training processes is resulting in personnel functioning in a proactive mode and increased customer satisfaction with training performance

  16. The marine corrosion program developed by Nuclebras

    International Nuclear Information System (INIS)

    Moreira, P.A.P.; Quinan, M.A.

    1986-01-01

    A marine corrosion program is being developed by NUCLEBRAS and NUCLEN. This program consists in carrying out non-accelerated experiments in marine atmosphere, with immersion in sewater and laboratory accelerated tests. The purpose is to obtain a correlation between the corrosion rates observed in non-accelerated conditions and laboratory tests. Through these results it is inteded, only with laboratory tests, to estimate the bahavior of similar materials when tsted in similar marine atmosphereic conditions. Some aspects observed in the implementation of the program and some results so far obtained are discussed. (Author) [pt

  17. Mars Technology Program Planetary Protection Technology Development

    Science.gov (United States)

    Lin, Ying

    2006-01-01

    The objectives of the NASA Planetary Protection program are to preserve biological and organic conditions of solar-system bodies for future scientific exploration and to protect the Earth from potential hazardous extraterrestrial contamination. As the exploration of solar system continues, NASA remains committed to the implementation of planetary protection policy and regulations. To fulfill this commitment, the Mars Technology Program (MTP) has invested in a portfolio of tasks for developing necessary technologies to meet planetary protection requirements for the next decade missions.

  18. Development of superconductor application technology - Flywheel energy storage system using superconducting magnetic bearing

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Soo Hun; Oh, Hueng Kuk; Yun, Keyng Reyl; Lee, Jeung Kun [Ahju University, Suwon (Korea, Republic of)

    1996-06-01

    Electricity must be used simultaneously with its generation. Existing storage methods either are dependent on special geography, are too expensive,= or are too inefficient. Electricity demand changes by as much as 30% over a 12-hour period and result in significant costs for utilities as power output get adjusted to meet these changes. The purpose of HTS FES is to store unused nighttime electricity until it is needed during the daytime. If every element of a rotating flywheel is stressed to a prescribed allowable value, the flywheel material will clearly be used in most efficient manner. The uniformlt stressed flywheel is about 25% stronger than a flat disk. The gap between superconductor and permanent magnet was 1.85 mm, and using bearing connector with the values, joining superconductor to permanent magnet Using bolt connector, joining permanent magnet to flywheel. Joined system is excited by exciting function that magnitude is 1, range is 0 up to 4000 HZ. 3 rd and 4 th natural frequency, 1857 HZ and 2340 HZ, in X direction and 2 nd natural frequency, 28.57 HZ, are avoided to prevent resonance. 15 refs., 11 tabs., 53 figs. (author)

  19. Transuranic waste management program waste form development

    International Nuclear Information System (INIS)

    Bennett, W.S.; Crisler, L.R.

    1981-01-01

    To ensure that all technology necessary for long term management of transuranic (TRU) wastes is available, the Department of Energy has established the Transuranic Waste Management Program. A principal focus of the program is development of waste forms that can accommodate the very diverse TRU waste inventory and meet geologic isolation criteria. The TRU Program is following two approaches. First, decontamination processes are being developed to allow removal of sufficient surface contamination to permit management of some of the waste as low level waste. The other approach is to develop processes which will allow immobilization by encapsulation of the solids or incorporate head end processes which will make the solids compatible with more typical waste form processes. The assessment of available data indicates that dewatered concretes, synthetic basalts, and borosilicate glass waste forms appear to be viable candidates for immobilization of large fractions of the TRU waste inventory in a geologic repository

  20. A formal mentorship program for faculty development.

    Science.gov (United States)

    Jackevicius, Cynthia A; Le, Jennifer; Nazer, Lama; Hess, Karl; Wang, Jeffrey; Law, Anandi V

    2014-06-17

    To describe the development, implementation, and evaluation of a formal mentorship program at a college of pharmacy. After extensive review of the mentorship literature within the health sciences, a formal mentorship program was developed between 2006 and 2008 to support and facilitate faculty development. The voluntary program was implemented after mentors received training, and mentors and protégés were matched and received an orientation. Evaluation consisted of conducting annual surveys and focus groups with mentors and protégés. Fifty-one mentor-protégé pairs were formed from 2009 to 2012. A large majority of the mentors (82.8%-96.9%) were satisfied with the mentorship program and its procedures. The majority of the protégés (≥70%) were satisfied with the mentorship program, mentor-protégé relationship, and program logistics. Both mentors and protégés reported that the protégés most needed guidance on time management, prioritization, and work-life balance. While there were no significant improvements in the proteges' number of grant submissions, retention rates, or success in promotion/tenure, the total number of peer-reviewed publications by junior faculty members was significantly higher after program implementation (mean of 7 per year vs 21 per year, p=0.03) in the college's pharmacy practice and administration department. A formal mentorship program was successful as measured by self-reported assessments of mentors and protégés.

  1. Development of radiation-hard electric connector with ball bearing for in-vessel remote maintenance equipment of ITER

    International Nuclear Information System (INIS)

    Ito, Akira; Obara, Kenjiro; Tada, Eisuke; Morita, Yousuke; Yagi, Toshiaki; Iida, Kazuhisa; Sato, Masaru.

    1997-12-01

    Development of radiation-hard electric connector with ball bearing for in-vessel remote maintenance equipment of ITER (International Thermonuclear Experimental Reactor) has been conducted. Since the in-vessel remote maintenance equipment is operated under the condition of 10 6 R/h gamma ray dose rate, the electric connector has to be radiation hard for an accumulation dose of 10 10 R. In addition, the simple attachment/removal mechanism is essential for remote operation. For this, the alumina (Al203) ceramics and a ball bearing were adopted to electric insulator and plug (male) of connector, respectively. The handling tests on attachment/removal of the connector were conducted by using master slave manipulator and general purpose robot with handling tool, and as a result, the validity of the attachment/removal mechanism was verified. In the gamma ray irradiation tests, which are under way, no degradation in break down voltage (1000V 1min.) up to 10 10 R was confirmed. However insulation resistance and contact resistance between contact pin and contact socket were deteriorated in proportion to the accumulation dose. Increase of contact resistance is considered due to an erosion of contact pin. (author)

  2. Load-Bearing Capacity and Retention of Newly Developed Micro-Locking Implant Prosthetic System: An In Vitro Pilot Study

    Directory of Open Access Journals (Sweden)

    Jae-Won Choi

    2018-04-01

    Full Text Available The aim of this study was to introduce the newly developed micro-locking implant prosthetic system and to evaluate the resulting its characteristics. To evaluate load-bearing capacity, 25 implants were divided into five groups: external-hexagon connection (EH, internal-octagon connection (IO, internal-hexagon connection (IH, one-body implant (OB, micro-locking implant system (ML. The maximum compressive load was measured using a universal testing machine (UTM according to the ISO 14801. Retention was evaluated in two experiments: (1 a tensile test of the structure modifications of the components (attachment and implant and (2 a tensile test after cyclic loading (total 5,000,000 cycles, 100 N, 2 Hz. The load-bearing capacity of the ML group was not significantly different from the other groups (p > 0.05. The number of balls in the attachment and the presence of a hexagonal receptacle did not show a significant correlation with retention (p > 0.05, but the shape of the retentive groove in the implant post had a statistically significant effect on retention (p < 0.05. On the other hand, the retention loss was observed during the initial 1,000,000 cycles, but an overall constant retention was maintained afterward. Various preclinical studies on this novel micro-locking implant prosthetic system should continue so that it can be applied in clinical practice.

  3. Development of Low Carbon Niobium Bearing High Strength F-B Dual Phase Steel with High Hole Expansion Property

    Science.gov (United States)

    Zhang, Lin; Xia, Ming-sheng; Xiong, Zi-liu; Du, Yan-bing; Qiao, Zhi-ming; Zhang, Hong-bo

    In the study a low carbon niobium bearing high strength F-B dual phase automobile steel with high hole expansion property has been investigated. Steels of different chemical composition have been investigated by simulation experiments of controlled rolling and cooling process to study the influences of chemical elements, especially for C,Nb and Ti, and cooling pattern on the mechanical properties, flangeability and microstructure of strips. So-called 3-stages cooling pattern was adopted in simulation experiments, combining ultra fast cooling in first stage, air cooling in middle stage and fast cooling in the last stage, and at the end of run-out table the temperature of rolled pieces drop to below Bs point. Optical microstructure and SEM morphology have been observed. Results indicate that it is possible to obtain dual phase microstructure of polygonal ferrite plus bainite in adopting 3-stages cooling pattern. The low temperature coiling method using 3-step controlled cooling pattern after hot rolling is effective to produce low carbon Nb bearing steel with high balance of strength-ductility-flangeability, in addition, higher carbon content of steel tend to be detrimental to flangeability of steel, due to much carbide precipitation at ferrite boundary. Based on the results of simulation experiments mill trial has been carried out and hot rolled high strength steel with tensile strength higher as 600Mpa and hole expansion ratio higher as 100% has been developed successfully.

  4. Porosity development in the Copper Ridge Dolomite and Maynardville Limestone, Bear Creek Valley and Chestnut Ridge, Tennessee

    International Nuclear Information System (INIS)

    Goldstrand, P.M.; Menefee, L.S.; Dreier, R.B.

    1995-12-01

    Matrix porosity data from deep core obtained in Bear Creek Valley indicate that porosities in the Maynardville Limestone are lithology and depth dependent. Matrix porosities are greater in the Cooper Ridge Dolomite than in the Maynardville Limestone, yet there is no apparent correlation with depth. Two interrelated diagenetic processes are the major controlling factors on porosity development in the Copper Ridge Dolomite and Maynardville Limestone; dissolution of evaporate minerals and dedolomitization. Both of these diagenetic processes produce matrix porosities between 2.1 and 1.3% in the Copper Ridge Dolomite and upper part of the Maynardville Limestone (Zone 6) to depths of approximately 600 ft bgs. Mean matrix porosities in Zones 5 through 2 of the Maynardville Limestone range from 0.8 to 0.5%. A large number of cavities have been intersected during drilling activities in nearly all zones of the Maynardville Limestone in Bear Creek Valley. Therefore, any maynardville Limestone zone within approximately 200 ft of the ground surface is likely to contain cavities that allow significant and rapid flow of groundwater. Zone 6 could be an important stratigraphic unit in the Maynardville Limestone for groundwater flow and contaminant transport because of the abundance of vuggy and moldic porosities. There are large variations in the thickness and lithology in the lower part of the Maynardville (Zones 2, 3, and 4 in the Burial Grounds region). The direction and velocity of strike-parallel groundwater flow may be altered in this area within the lower Maynardville Limestone

  5. Mars Technology Program: Planetary Protection Technology Development

    Science.gov (United States)

    Lin, Ying

    2006-01-01

    This slide presentation reviews the development of Planetary Protection Technology in the Mars Technology Program. The goal of the program is to develop technologies that will enable NASA to build, launch, and operate a mission that has subsystems with different Planetary Protection (PP) classifications, specifically for operating a Category IVb-equivalent subsystem from a Category IVa platform. The IVa category of planetary protection requires bioburden reduction (i.e., no sterilization is required) The IVb category in addition to IVa requirements: (i.e., terminal sterilization of spacecraft is required). The differences between the categories are further reviewed.

  6. The use of teddy bears to help develop interpersonal context to promote intrinsic motivation

    Directory of Open Access Journals (Sweden)

    Tamatha Rabb Andrews

    2004-01-01

    Full Text Available El siguiente artículo esta basado en los resultados obtenidos de una investigación cuyo objetivo fue el utilizar un oso de peluche como una herramienta para incrementar la motivación de los estudiantes hacia el aprendizaje del inglés como segunda lengua. Esta trabajo investigativo fue desarrollado esperando mejorar no solo la motivación de los educandos por medio de este recurso novedoso, sino también darle un giro positivo al ambiente de relaciones interpersonales en la institución donde se realizo este proyecto. Los estudiantes sujetos de esta investigación, participaron en forma voluntaria, lo cuál consistió en cuidar el oso de peluche, al que se le llamó Ken Bear, como si fuera su amigo o compañero de juego por un día o varios. Al final de este tiempo, los estudiantes escribieron una pequeña composición de su experiencia en compañía del osito. Esta composición, realizada en idioma inglés, debía escribirse en un diario que portaba el oso de peluche dentro de un salveque. Si los estudiantes por alguna razón, como la edad o limitación hacia la expresión en este idioma, no podían realizar tal tarea, se les permitió hacerlo en Español o bien, ilustrar con un dibujo que incluía algunas palabras en este idioma. Los resultados indican que esta estrategia fue exitosa de acuerdo a los resultados obtenidos que se vieron reflejados en el trabajo de clase de los involucrados en ella, y a las opiniones recolectadas por esta investigadora de los padres de familia y docentes involucrados en esta investigación.

  7. Recent developments of the US RERTR program

    International Nuclear Information System (INIS)

    Travelli, A.

    1983-01-01

    The status of the US Reduced Enrichment Research and Test Reactor (RERTR) Program is reviewed. After a brief outline of the RERTR Program objectives, goals and past accomplishments, emphasis is placed on the developments which took place during 1983 and on current program plans and schedules. Most program activities have proceeded as planned and a combination of two silicide fuels (U 3 Si 2 -Al and U 3 Si-Al) was found to hold excellent promise for achieving the long-term program goals. A modification of the program plan, including the development and demonstration of those fuels, was prepared and is now being implemented. The uranium density of qualified RERTR fuels for plate-type reactors is forecasted to grow by approximately 1 g U/cm 3 each year, from the current 1.7 g U/cm 3 to the 7.0 g U/cm 3 which will be reached in 1988. The technical needs of research reactors for HEU exports are also forecasted to undergo a gradual and dramatic decline in the coming years

  8. Grizzly bear density in Glacier National Park, Montana

    Science.gov (United States)

    Kendall, K.C.; Stetz, J.B.; Roon, David A.; Waits, L.P.; Boulanger, J.B.; Paetkau, David

    2008-01-01

    We present the first rigorous estimate of grizzly bear (Ursus arctos) population density and distribution in and around Glacier National Park (GNP), Montana, USA. We used genetic analysis to identify individual bears from hair samples collected via 2 concurrent sampling methods: 1) systematically distributed, baited, barbed-wire hair traps and 2) unbaited bear rub trees found along trails. We used Huggins closed mixture models in Program MARK to estimate total population size and developed a method to account for heterogeneity caused by unequal access to rub trees. We corrected our estimate for lack of geographic closure using a new method that utilizes information from radiocollared bears and the distribution of bears captured with DNA sampling. Adjusted for closure, the average number of grizzly bears in our study area was 240.7 (95% CI = 202–303) in 1998 and 240.6 (95% CI = 205–304) in 2000. Average grizzly bear density was 30 bears/1,000 km2, with 2.4 times more bears detected per hair trap inside than outside GNP. We provide baseline information important for managing one of the few remaining populations of grizzlies in the contiguous United States.

  9. Seismic isolation development for the US advanced liquid-metal reactor program

    International Nuclear Information System (INIS)

    Gluekler, E.L.; Bigelow, C.C.; DeVita, V.; Kelly, J.M.; Seidensticker, R.W.; Tajirian, F.F.

    1989-01-01

    GE Nuclear Energy, in association with a US Industrial Team and support from the US National Laboratories and Universities, is developing a modular liquid-metal reactor concept for the US Department of Energy (DOE). The objective of this development is to provide, by the turn of the century, a reactor concept with optimized passive safety features that is economically competitive with other domestic energy sources, licensable, and ready for commercial deployment. One of the unique features of the concept is the seismic isolation of the reactor modules which decouples the reactor and their safety systems from potentially damaging ground motions and significantly enhances the structural resistance to high energy, as well as long duration earthquakes. Seismic isolation is accomplished with high damping natural rubber bearings. The reactors are located in individual silos below grade level and are supported by the isolator bearings at approximately their center of gravity. This application of seismic isolation is the first for a US nuclear power plant. A development program has been established to assure the full benefits from the utilization of this new approach and to provide adequate system characterization and qualification for licensing certification. The development program is described in this paper and selected results are presented. The initial testing indicated excellent performance of high damping natural rubber bearings

  10. Calendar year 1994 groundwater quality report for the Bear Creek hydrogeologic regime, Y-12 Plant, Oak Ridge, Tennessee. 1994 Groundwater quality data interpretations and proposed program modifications

    International Nuclear Information System (INIS)

    1995-10-01

    This groundwater quality report (GWQR) contains an evaluation of the groundwater quality data obtained during the 1994 calendar year (CY) at several hazardous and non-hazardous waste management facilities at the US Department of Energy (DOE) Y-12 Plant. These sites lie in Bear Creek Valley (BCV) west of the Y-12 Plant within the boundaries of the Bear Creek Hydrogeologic Regime which is one of three hydrogeologic regimes defined for the purposes of groundwater quality monitoring. The Environmental Management Department manages the groundwater monitoring activities under the auspices of the Y-12 Plant Groundwater Protection Program (GWPP). The purpose of the GWPP is to characterize the hydrogeology and to monitor groundwater quality at the Y-12 Plant and surrounding area to protect local groundwater resources. The annual GWQR for the Bear Creek Regime is completed in two parts. Part 1 consists primarily of data appendices and serves as a reference for the groundwater quality data obtained each CY. Part 2 (this report) contains an evaluation of the data with respect to regime-wide groundwater quality, summarizes the status and findings of ongoing hydrogeologic studies, describes changes in monitoring priorities, and presents planned modifications to the groundwater sampling and analysis activities

  11. Rolling bearing analysis

    CERN Document Server

    Harris, Tedric A

    2001-01-01

    One of the most well-known experts in the field brings cutting-edge research to practitioners in the new edition of this important reference. Covers the improved mathematical calculations for rolling bearing endurance developed by the American Society of Mechanical Engineers and the Society of Lubrication and Tribology Engineers. Updated with new material on Condition-Based Maintenance, new testing methods, and new bearing materials.

  12. Professional Development Programs for Teachers of English

    Directory of Open Access Journals (Sweden)

    Singgih Widodo

    2016-02-01

    Full Text Available Well-planned programs based on the needs for professional development of teachers are strongly needed to enhance the teaching-staff improvement.The impact of teacher improvement will effect the students learning and school achievement. This paper aims at raising awareness of English teachers to upgrade themselves as autonomous learners as well as researchers and broaden their horizon for stepping the ladder-career of their profession. For that purpose, a survey as reported here aimed to identify the needs of individual English teachers and the preferred programs for professional development. The findings indicated that the 36 teachers involved needed teacher training, teacher association, teacher materials, continuing education, and interschool visit and that teacher training was the most well known program among teachers.

  13. Development of an MPI benchmark program library

    Energy Technology Data Exchange (ETDEWEB)

    Uehara, Hitoshi

    2001-03-01

    Distributed parallel simulation software with message passing interfaces has been developed to realize large-scale and high performance numerical simulations. The most popular API for message communication is an MPI. The MPI will be provided on the Earth Simulator. It is known that performance of message communication using the MPI libraries gives a significant influence on a whole performance of simulation programs. We developed an MPI benchmark program library named MBL in order to measure the performance of message communication precisely. The MBL measures the performance of major MPI functions such as point-to-point communications and collective communications and the performance of major communication patterns which are often found in application programs. In this report, the description of the MBL and the performance analysis of the MPI/SX measured on the SX-4 are presented. (author)

  14. Counter Trafficking System Development "Analysis Training Program"

    Energy Technology Data Exchange (ETDEWEB)

    Peterson, Dennis C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2010-12-01

    This document will detail the training curriculum for the Counter-Trafficking System Development (CTSD) Analysis Modules and Lesson Plans are derived from the United States Military, Department of Energy doctrine and Lawrence Livermore National Laboratory (LLNL), Global Security (GS) S Program.

  15. Developing a Systematic Patent Search Training Program

    Science.gov (United States)

    Zhang, Li

    2009-01-01

    This study aims to develop a systematic patent training program using patent analysis and citation analysis techniques applied to patents held by the University of Saskatchewan. The results indicate that the target audience will be researchers in life sciences, and aggregated patent database searching and advanced search techniques should be…

  16. Programming language concepts for software developers

    DEFF Research Database (Denmark)

    Sestoft, Peter

    2008-01-01

    This note describes and motivates our current plans for an undergraduate course on programming language concepts for software development students. We describe the competences we expect students to acquire as well as the topics covered by the course. We plan to use C# and Scheme as instruction...

  17. The AECL research and development program

    International Nuclear Information System (INIS)

    Hart, R.G.; Woods, A.D.B.

    1980-02-01

    The research and development program of the Atomic Energy of Canada Research Company is briefly described. Goals and objectives are emphasized, some recent highlights are given and the importance of technology transfer is discussed. A short representative bibliography is included. (auth)

  18. The Mentoring Experience: Leadership Development Program Perspectives

    Science.gov (United States)

    Lamm, Kevan W.; Sapp, Rochelle; Lamm, Alexa J.

    2017-01-01

    Using a semi-structured interview approach, ten mentors from a leadership development program focused on building leaders in Colleges of Agriculture and Life Sciences across the nation provided insights regarding their mentoring method, process, and experiences. Mentors interviewed agreed the mentoring process was beneficial for themselves as well…

  19. Career Development Programs in Fortune 500 Firms.

    Science.gov (United States)

    Keller, Jack; Piotrowski, Chris

    Career development programs (CDPs) are a rather recent area of study in organizational and industrial psychology. The present study investigated the nature and evaluation of CDPs in Fortune 500 firms. Data were obtained by a mailed questionnaire completed by the firms' human resources directors. Of the 500 companies surveyed, only those 50 that…

  20. Research and Development Conference CIEE Program 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-11-01

    CIEE`s second annual Research and Development Conference will introduce you to some of the results achieved to date through CIEE-sponsored multiyear research performed in three programs: Building Energy Efficiency, Air Quality Impacts of Energy Efficiency, and End-Use Resource Planning. Results from scoping studies, Director`s discretionary research, and exploratory research will also be featured in this report.

  1. Thermohydrodynamic analysis of cryogenic liquid turbulent flow fluid film bearings, phase 2

    Science.gov (United States)

    Sanandres, Luis

    1994-01-01

    The Phase 2 (1994) Annual Progress Report presents two major report sections describing the thermal analysis of tilting- and flexure-pad hybrid bearings, and the unsteady flow and transient response of a point mass rotor supported on fluid film bearings. A literature review on the subject of two-phase flow in fluid film bearings and part of the proposed work for 1995 are also included. The programs delivered at the end of 1994 are named hydroflext and hydrotran. Both codes are fully compatible with the hydrosealt (1993) program. The new programs retain the same calculating options of hydrosealt plus the added bearing geometries, and unsteady flow and transient forced response. Refer to the hydroflext & hydrotran User's Manual and Tutorial for basic information on the analysis and instructions to run the programs. The Examples Handbook contains the test bearing cases along with comparisons with experimental data or published analytical values. The following major tasks were completed in 1994 (Phase 2): (1) extension of the thermohydrodynamic analysis and development of computer program hydroflext to model various bearing geometries, namely, tilting-pad hydrodynamic journal bearings, flexure-pad cylindrical bearings (hydrostatic and hydrodynamic), and cylindrical pad bearings with a simple elastic matrix (ideal foil bearings); (2) improved thermal model including radial heat transfer through the bearing stator; (3) calculation of the unsteady bulk-flow field in fluid film bearings and the transient response of a point mass rotor supported on bearings; and (4) a literature review on the subject of two-phase flows and homogeneous-mixture flows in thin-film geometries.

  2. Identifying needs to develop a PBL staff development program

    Directory of Open Access Journals (Sweden)

    Prarthana Coffin

    2013-08-01

    Full Text Available Staff development is a crucial element for educational intervention. Recognizing the importance of staff development, this study aims to pin-point suitable methodologies in developing a Problem-Based Learning (PBL academic staff development program for a higher education institute where PBL has become an intervention alternative. The study aims to answer the following research questions 1 how can university academic staff be assisted to acquire pedagogical competences for an initiative of the implementation of PBL curriculum? 2 What kinds of support do university academic staff need in order to maintain PBL implementation? Through a combination of a literature review, interviews with 6 PBL experts which emphasize the importance of PBL facilitators, and document analysis of reflection notes from 18 trainees of a PBL workshop, this study will produce a guideline in developing a PBL Academic Staff Development Program for an institute wishes to implement and retain PBL as the education strategy.

  3. Bioenergy Feedstock Development Program Status Report

    Energy Technology Data Exchange (ETDEWEB)

    Kszos, L.A.

    2001-02-09

    The U.S. Department of Energy's (DOE's) Bioenergy Feedstock Development Program (BFDP) at Oak Ridge National Laboratory (ORNL) is a mission-oriented program of research and analysis whose goal is to develop and demonstrate cropping systems for producing large quantities of low-cost, high-quality biomass feedstocks for use as liquid biofuels, biomass electric power, and/or bioproducts. The program specifically supports the missions and goals of DOE's Office of Fuels Development and DOE's Office of Power Technologies. ORNL has provided technical leadership and field management for the BFDP since DOE began energy crop research in 1978. The major components of the BFDP include energy crop selection and breeding; crop management research; environmental assessment and monitoring; crop production and supply logistics operational research; integrated resource analysis and assessment; and communications and outreach. Research into feedstock supply logistics has recently been added and will become an integral component of the program.

  4. Laboratory Directed Research ampersand Development Program

    International Nuclear Information System (INIS)

    Ogeka, G.J.; Romano, A.J.

    1993-12-01

    At Brookhaven National Laboratory the Laboratory Directed Research and Development (LDRD) Program is a discretionary research and development tool critical in maintaining the scientific excellence and vitality of the laboratory. It is also a means to stimulate the scientific community, fostering new science and technology ideas, which is the major factor in achieving and maintaining staff excellence, and a means to address national needs, within the overall mission of the Department of Energy and Brookhaven National Laboratory. This report summarizes research which was funded by this program during fiscal year 1993. The research fell in a number of broad technical and scientific categories: new directions for energy technologies; global change; radiation therapies and imaging; genetic studies; new directions for the development and utilization of BNL facilities; miscellaneous projects. Two million dollars in funding supported 28 projects which were spread throughout all BNL scientific departments

  5. Impact of a student leadership development program.

    Science.gov (United States)

    Chesnut, Renae; Tran-Johnson, Jennifer

    2013-12-16

    To assess the effectiveness of the Student Leadership Development Series (SLDS), an academic-year--long, co-curricular approach to developing leadership skills in pharmacy students. Participants met once per month for activities and a college-wide guest speaker session. Students also completed monthly forms regarding what they had learned, participated in poster presentations, and created a personal leadership platform. One hundred twenty-three students participated in the program between 2008 and 2013. On monthly evaluation forms and a summative evaluation, students indicated that the program helped them feel prepared for leadership opportunities and increased their desire to pursue leadership. They valued interacting with pharmacy leaders from the community and learning how they could distinguish themselves as leaders. The SLDS provided pharmacy students with an opportunity to explore personal leadership styles and develop broader understanding of leadership, and increased their desire to pursue leadership positions in the future.

  6. Target developments program to prepare LMJ campaigns

    Energy Technology Data Exchange (ETDEWEB)

    Collier, R; Bachelet, F; Botrel, R; Breton, O; Chicanne, C; Dauteuil, C H; Durut, F; Fleury, E; Guillot, L; Hermerel, C; Jeannot, L; Legaie, O; Legay, G; Martin, M; Reneaume, B; Theobald, M; Vincent-Viry, O, E-mail: remy.collier@cea.f [Commissariat a l' Energie Atomique, Direction des Applications Militaires, Valduc, F-21120 Is-sur-Tille (France)

    2010-08-01

    To carry out laser plasma experiments on CEA laser facilities, a R and D program was set up and is still under way to deliver complex targets. For a decade, specific developments are also dedicated to 'Ligne d'Integration Laser' (LIL) in France and Omega facilities (USA). To prepare the targets intended for the first experiments on the Laser 'Megajoule' (LMJ) facility, new developments are required, such as cocktail hohlraum fabrication, gas barrier coating and foam shells developments. For fusion experiments on LMJ, an important program is also under way to elaborate the Cryogenic Target Assembly (CTA), to fill and transport the CTA and to study the conformation process of the DT layer.

  7. Integrated rural development programs: a skeptical perspective.

    Science.gov (United States)

    Ruttan, V W

    1975-11-01

    In examining integrated rural development programs the question that arises is why is it possible to identify several relatively successful small-scale or pilot rural development projects yet so difficult to find examples of successful rural development programs. 3 bodies of literature offer some insight into the morphology of rural development projects, programs, and processes: the urban-industrial impact hypothesis; the theory of induced technical change; and the new models of institutional change that deal with institution building and the economics of bureaucratic behavior. The urban-industrial impact hypothesis helps in the clarification of the relationships between the development of rural areas and the development of the total society of which rural areas are a part. It is useful in understanding the spatial dimensions of rural development where rural development efforts are likely to be most successful. Formulation of the hypothesis generated a series of empirical studies designed to test its validity. The effect of these studies has been the development of a rural development model in which the rural community is linked to the urban-industrial economy through a series of market relationships. Both the urban economy's rate of growth and the efficiency of the intersector product and factor markets place significant constraints on the possibilities of rural area development. It is not possible to isolate development processes in the contemporary rural community in a developing society from development processes in the larger society. The induced technical change theory provides a guide as to what must be done to gain access to efficient sources of economic growth, the new resources and incomes that are necessary to sustain rural development. Design of a successful rural development strategy involves a combination of technical and institutional change. The ability of rural areas to respond to the opportunities for economic growth generated by local urban

  8. European Community's program in marine resources development

    International Nuclear Information System (INIS)

    Lenoble, J.P.; Jarmache, E.

    1995-01-01

    The European Community launched already several research program in the different fields of social and industrial activities. The Fourth Framework Programme is divided into 4 main activities comporting a total of 18 programs. These programs are dealing with general topics as information and communication, industrial technologies, environment, life sciences and technologies, energy, transport and socioeconomic research. One line is devoted to marine sciences and technology, but offshore activities could also be included in the other topics as offshore oil and gas in energy, ship building and harbor in transport, aquaculture and fisheries in life sciences and technology, etc. In order to maintain a coherent approach toward offshore activities, the European maritime industries met intensively front 1991 to 1994 and recommended a series of proposal for Research and Development of marine resources. The methodology and content of these proposals is exposed

  9. Proposed tokamak poloidal field system development program

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, J.D.; Vogel, H.F.; Warren, R.W.; Weldon, D.M.

    1977-05-01

    A program is proposed to develop poloidal field components for TNS and EPR size tokamak devices and to test these components in realistic circuits. Emphasis is placed upon the development of the most difficult component, the superconducting ohmic-heating coil. Switches must also be developed for testing the coils, and this switching technology is to be extended to meet the requirements for the large scale tokamaks. Test facilities are discussed; power supplies, including a homopolar to drive the coils, are considered; and poloidal field systems studies are proposed.

  10. Tubular solid oxide fuel cell development program

    Energy Technology Data Exchange (ETDEWEB)

    Ray, E.R.; Cracraft, C.

    1995-12-31

    This paper presents an overview of the Westinghouse Solid Oxide Fuel Cell (SOFC) development activities and current program status. The Westinghouse goal is to develop a cost effective cell that can operate for 50,000 to 100,000 hours. Progress toward this goal will be discussed and test results presented for multiple single cell tests which have now successfully exceeded 56,000 hours of continuous power operation at temperature. Results of development efforts to reduce cost and increase power output of tubular SOFCs are described.

  11. SIMS analysis: Development and evaluation program summary

    International Nuclear Information System (INIS)

    Groenewold, G.S.; Appelhans, A.D.; Ingram, J.C.; Delmore, J.E.; Dahl, D.A.

    1996-11-01

    This report provides an overview of the ''SIMS Analysis: Development and Evaluation Program'', which was executed at the Idaho National Engineering Laboratory from mid-FY-92 to the end of FY-96. It should be noted that prior to FY-1994 the name of the program was ''In-Situ SIMS Analysis''. This report will not go into exhaustive detail regarding program accomplishments, because this information is contained in annual reports which are referenced herein. In summary, the program resulted in the design and construction of an ion trap secondary ion mass spectrometer (IT-SIMS), which is capable of the rapid analysis of environmental samples for adsorbed surface contaminants. This instrument achieves efficient secondary ion desorption by use of a molecular, massive ReO 4 - primary ion particle. The instrument manages surface charge buildup using a self-discharging principle, which is compatible with the pulsed nature of the ion trap. The instrument can achieve high selectivity and sensitivity using its selective ion storage and MS/MS capability. The instrument was used for detection of tri-n-butyl phosphate, salt cake (tank cake) characterization, and toxic metal speciation studies (specifically mercury). Technology transfer was also an important component of this program. The approach that was taken toward technology transfer was that of component transfer. This resulted in transfer of data acquisition and instrument control software in FY-94, and ongoing efforts to transfer primary ion gun and detector technology to other manufacturers

  12. IAEA Nuclear Security Human Resource Development Program

    International Nuclear Information System (INIS)

    Braunegger-Guelich, A.

    2009-01-01

    The IAEA is at the forefront of international efforts to strengthen the world's nuclear security framework. The current Nuclear Security Plan for 2006-2009 was approved by the IAEA Board of Governors in September 2005. This Plan has three main points of focus: needs assessment, prevention, detection and response. Its overall objective is to achieve improved worldwide security of nuclear and other radioactive material in use, storage and transport, and of their associated facilities. This will be achieved, in particular, through the provision of guidelines and recommendations, human resource development, nuclear security advisory services and assistance for the implementation of the framework in States, upon request. The presentation provides an overview of the IAEA nuclear security human resource development program that is divided into two parts: training and education. Whereas the training program focuses on filling gaps between the actual performance of personnel working in the area of nuclear security and the required competencies and skills needed to meet the international requirements and recommendations described in UN and IAEA documents relating to nuclear security, the Educational Program in Nuclear Security aims at developing nuclear security experts and specialists, at fostering a nuclear security culture and at establishing in this way sustainable knowledge in this field within a State. The presentation also elaborates on the nuclear security computer based learning component and provides insights into the use of human resource development as a tool in achieving the IAEA's long term goal of improving sustainable nuclear security in States. (author)

  13. Laboratory Directed Research and Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Ogeka, G.J.

    1991-12-01

    Today, new ideas and opportunities, fostering the advancement of technology, are occurring at an ever-increasing rate. It, therefore, seems appropriate that a vehicle be available which fosters the development of these new ideas and technologies, promotes the early exploration and exploitation of creative and innovative concepts, and which develops new fundable'' R D projects and programs. At Brookhaven National Laboratory (BNL), one such method is through its Laboratory Directed Research and Development (LDRD) Program. This discretionary research and development tool is critical in maintaining the scientific excellence and vitality of the Laboratory. Additionally, it is a means to stimulate the scientific community, fostering new science and technology ideas, which is the major factor achieving and maintaining staff excellence, and a means to address national needs, with the overall mission of the Department of Energy (DOE) and the Brookhaven National Laboratory. The Project Summaries with their accomplishments described in this report reflect the above. Aside from leading to new fundable or promising programs and producing especially noteworthy research, they have resulted in numerous publications in various professional and scientific journals, and presentations at meetings and forums.

  14. Meteorological Development Laboratory Student Career Experience Program

    Science.gov (United States)

    McCalla, C., Sr.

    2007-12-01

    The National Oceanic and Atmospheric Administration's (NOAA) National Weather Service (NWS) provides weather, hydrologic, and climate forecasts and warnings for the protection of life and property and the enhancement of the national economy. The NWS's Meteorological Development Laboratory (MDL) supports this mission by developing meteorological prediction methods. Given this mission, NOAA, NWS, and MDL all have a need to continually recruit talented scientists. One avenue for recruiting such talented scientist is the Student Career Experience Program (SCEP). Through SCEP, MDL offers undergraduate and graduate students majoring in meteorology, computer science, mathematics, oceanography, physics, and statistics the opportunity to alternate full-time paid employment with periods of full-time study. Using SCEP as a recruiting vehicle, MDL has employed students who possess some of the very latest technical skills and knowledge needed to make meaningful contributions to projects within the lab. MDL has recently expanded its use of SCEP and has increased the number of students (sometimes called co- ops) in its program. As a co-op, a student can expect to develop and implement computer based scientific techniques, participate in the development of statistical algorithms, assist in the analysis of meteorological data, and verify forecasts. This presentation will focus on describing recruitment, projects, and the application process related to MDL's SCEP. In addition, this presentation will also briefly explore the career paths of students who successfully completed the program.

  15. Initial developments in the Stanford SQUIRT program

    Science.gov (United States)

    Kitts, Christopher A.; Twiggs, Robert J.

    1995-01-01

    Stanford University's Department of Aeronautics and Astronautics has commenced full scale development of a new microsatellite initiative. Known as the satellite quick research testbed (SQUIRT) program, the project's goal is to produce student engineered satellites capable of servicing state-of-the-art research payloads on a yearly basis. This program is specifically designed to meet the education and research goals of the department's Satellite Systems Development Laboratory. SQUIRT vehicles are envisioned to consist of a 25 pound, 9 inch tall, 16 inch diameter hexagonal structure with complete processor, communications, power, thermal, and attitude subsystems. These spacecraft cater to low power, volume, and mass research experiments and student developed educational packages. Mission lifetimes of up to one year are considered. Through student participation, voluntary mentoring from the academic and industrial communities, and the extensive use of off-the-shelf components, the cash outlay target for SQUIRT class vehicles is $50,000. This paper discusses the educational and research issues surrounding the development of Stanford's spacecraft design curriculum and the formulation of the SQUIRT program. A technical review of the first SQUIRT satellite, named SAPPHIRE, and an outline of the conceptual plans for other missions is also presented. Additionally, initiatives concerning partner academic institutions and public domain design information are featured.

  16. Who will bear the torch tomorrow? Charismatic leadership and second-line leaders in development NGOs

    OpenAIRE

    M. Shameem Siddiqi

    2001-01-01

    Competent leadership has always been considered vital in every organisation and there has been considerable research on mainstream leadership issues in the corporate sector and in politics.1 But there has been very little research on leadership issues in the emerging sector of development NGOs. The issue of second-line leadership development2 is an important one not only for the NGOs themselves but also for the aid industry, the poor and vulnerable people for whom they work and for society as...

  17. Nuclear power programs in the world's developed and developing countries

    International Nuclear Information System (INIS)

    Czibolya, L.

    1983-01-01

    The significance of nuclear power in the world's energy balance related to fossile energy sources is discussed. The general trend of declination of the national power programs could be observed from the seventies as a result of the oil crisis and the economic recession. The main features of the national energy programs including the ratio of the different energy sources in the power supply, the distribution of power production among the different types of nuclear reactors, the time schedules of the national nuclear power programs are reviewed through the examples of some developed and developing countries: USA, FRG, Canada, Japan, France, Sweden, the Soviet Union, Czechoslovakia, Bulgaria, Hungary, Romania, India, and the Republic of Korea. (V.N.)

  18. Clean Technology Evaluation & Workforce Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Patricia Glaza

    2012-12-01

    The overall objective of the Clean Technology Evaluation portion of the award was to design a process to speed up the identification of new clean energy technologies and match organizations to testing and early adoption partners. The project was successful in identifying new technologies targeted to utilities and utility technology integrators, in developing a process to review and rank the new technologies, and in facilitating new partnerships for technology testing and adoption. The purpose of the Workforce Development portion of the award was to create an education outreach program for middle & high-school students focused on clean technology science and engineering. While originally targeting San Diego, California and Cambridge, Massachusetts, the scope of the program was expanded to include a major clean technology speaking series and expo as part of the USA Science & Engineering Festival on the National Mall in Washington, D.C.

  19. Orthopaedic measurements with computed radiography: Methodological development, accuracy, and radiation dose with special reference to the weight-bearing lower extremity and the dislocating patella

    Energy Technology Data Exchange (ETDEWEB)

    Sanfridsson, J. [Univ. Hospital, Lund (Sweden). Dept. of Diagnostic Radiology

    2001-03-01

    The overall aim of this study was to develop and evaluate a measurement system for computed radiography and Picture Archiving and Communication Systems, permitting measurements of long distances and angles in and between related images. The developed measurement system, which was based on the QUESTOR Precision Radiography system, was applied to the weight-bearing knee with special reference to the dislocating patella. The QPR system modified for CR fulfilled the criteria for measuring the weight-bearing knee. The special measuring assistance tools that were developed were important for the implementation of CR and PACS, particularly in workstations programmed for musculoskeletal radiology. The energy imparted to the patient was reduced by 98% at the lowest exposure of the CR-system, compared with our conventional analogue method, without loss of diagnostic accuracy. The CR technique creates a possibility, to an extent not previously feasible, to differentiate the exposure parameters (and thus minimise the radiation dose to the patient) by carefully considering the purpose of the examination. A radiographic method for measuring the rotation of the femur and the tibia, and the patellar translation was developed and applied to healthy volunteers. The introduced patellar variables have yielded new insights into the complex sequence of motions between the femur, tibia, and patella. The patients with a dislocating patella were subdivided into one 'clean' group of spontaneous dislocations and one group with various traumas in the history, which thus resulted in two groups with distinct radiographic differences. The Q-angle was decreased in knees that had suffered dislocations, and the traditional surgical treatment with a further reduction of the Q-angle must be challenged. The use of clinical measurements of the Q-angle was not an optimal way to evaluate the mechanical alignment in the patellofemoral joint under physiological conditions. In this study, we have

  20. The Development of Individualized Education Programs

    Directory of Open Access Journals (Sweden)

    William H. Blackwell

    2014-04-01

    Full Text Available There are more than 6.6 million students with disabilities in U.S. public schools who receive special education services, which means that there are 6.6 million Individualized Education Programs (IEPs that have been developed and are being implemented at any given time. Each IEP represents real cost in educational opportunity, relationship building between families and schools, time, and resource allocation. Given this information, it is important to examine what we have learned from research on the development of IEPs, and to begin charting a new direction for research and practice related to IEP development. This literature review examines published, peer-reviewed research studies that have examined IEP development since the 1997 reauthorization of the Individuals With Disabilities Education Act (IDEA. The review concludes with a discussion of how findings from previous research on IEP development can inform future research agendas, educator practice, and federal and state policies.

  1. The WIPP research and development test program

    International Nuclear Information System (INIS)

    Tyler, L.D.

    1985-01-01

    The WIPP (Waste Isolation Pilot Plant) is a DOE RandD Facility for the purpose of developing the technology needed for the safe disposal of the United States defense-related radioactive waste. The in-situ test program is defined for the thermal-structural interactions, plugging and sealing, and waste package interactions in a salt environment. An integrated series of large-scale underground tests address the issues of both systems and long-term isolation performance of a repository

  2. Developing a meaningful QA trend analysis program

    International Nuclear Information System (INIS)

    Sternberg, A.

    1987-01-01

    A trend analysis program is being developed by the nuclear quality assurance (NQA) department at Public Service Electric and Gas Company, adapted from the principles advocated by W. Edwards Deming using statistical process control methods. It deals with identifying performance indicators that monitor the activities of a process considering both inputs and outputs, determining whether the process is stable or unstable, taking actions accordingly, and continuing to monitor the process with the objective of continual improvement of quality

  3. Game Programming Course - Creative Design and Development

    Directory of Open Access Journals (Sweden)

    Jaak Henno

    2008-10-01

    Full Text Available Rapid developments of the Electronic Entertainment - computer and video games, virtual environments, the "Games 3.0" revolution - influences also courses about Games and Virtual Environments. In the following is discussed the course “Games and Virtual Environments” presented in the fall 2007 term in Tallinn University of Technology; the main emphasis of the course was not on programming technology, but on understanding games as a special form of communication and exploring specific features of this form.

  4. Research and Development Conference CIEE Program 1992

    Energy Technology Data Exchange (ETDEWEB)

    1992-01-01

    CIEE's second annual Research and Development Conference will introduce you to some of the results achieved to date through CIEE-sponsored multiyear research performed in three programs: Building Energy Efficiency, Air Quality Impacts of Energy Efficiency, and End-Use Resource Planning. Results from scoping studies, Director's discretionary research, and exploratory research will also be featured in this report.

  5. Instructor development program at Three Mile Island

    International Nuclear Information System (INIS)

    Irizarry, C.A.; Jones, J.W.; Knief, R.

    1981-01-01

    The Three Mile Island (TMI) Training Department has prepared and conducted Instructor Development Programs which have upgraded the capabilities of its instructors and provided more uniformity among its diverse efforts. The week-long course was prepared in-house by a staff that combined college teaching experience in both education and technical subjects with strong background in industrial training. Through the first two offerings of the course, twenty-five individuals have participated and eight have served on the course staff

  6. Borehole Plugging-Materials Development Program

    International Nuclear Information System (INIS)

    Gulick, C.W. Jr.

    1978-06-01

    This report discusses the background and first year's results of the grouting materials development program for plugging boreholes associated with the Nuclear Waste Isolation Pilot Plant. The grouts are to be pumpable, impermeable, and durable for many thousands of years. The work was done at the Concrete Laboratory of the U.S. Army Engineer Waterways Experiment Station (WES), Vicksburg, Mississippi. The workability, strength, porosity, bonding, expansion, and permeability data are summarized and discussed. The work is continuing at WES

  7. A technology development summary for the AGT101 Advanced Gas Turbine Program

    Energy Technology Data Exchange (ETDEWEB)

    Boyd, G.L.; Kidwell, J.R.; Kreiner, D.M.

    1987-01-01

    Since the program initiation in October 1979, the Garrett/Ford Advanced Gas Turbine Program, designated AGT101, has made significant progress in developing ceramic technology for gas turbine applications. Successful component development has resulted in engine tests with an all ceramic hot section to temperatures up to 2200F (1204C) and full speed operation to 100,000 rpm (turbine rotor tip speed of 2300 ft/sec (701 m/s)). An 85-hour test was performed on an all ceramic engine at 2200F (1204C) turbine inlet temperature. These engine tests represent important first steps in the development of ceramic materials and technology. Engine evaluation was preceded by important component development. Activities included aerodynamic component evaluation and development of a high temperature foil bearing to support the ceramic turbine rotor. Development of low leakage regenerator seals and static ceramic seals in this high temperature environment were critical to engine performance.

  8. The development of a low vibration, long life pulse tube employing flexural bearings

    International Nuclear Information System (INIS)

    Olson, D.B.; Riggle, P.; Gedeon, D.

    1992-01-01

    This paper reports on a 1/3 watt, 80 K Technology Demonstration Model (TDM) pulse tube cryocooler which has been developed by Stirling Technology Company (STC). The pulse tube expander has no moving parts, making it simpler, more reliable, lower in cost, and lower in vibration than a Stirling expander. The pulse tube expander was designed, built, and tested with SBIR Phase I funding from NASA Ames Research Center. The pulse tube expander was driven using an existing dual opposed compressor module from a TDM Stirling cryocooler. Two numerical models were developed for pulse tube cryocoler design, evaluation, and analysis

  9. Hypoxia: From Placental Development to Fetal Programming.

    Science.gov (United States)

    Fajersztajn, Lais; Veras, Mariana Matera

    2017-10-16

    Hypoxia may influence normal and different pathological processes. Low oxygenation activates a variety of responses, many of them regulated by hypoxia-inducible factor 1 complex, which is mostly involved in cellular control of O 2 consumption and delivery, inhibition of growth and development, and promotion of anaerobic metabolism. Hypoxia plays a significant physiological role in fetal development; it is involved in different embryonic processes, for example, placentation, angiogenesis, and hematopoiesis. More recently, fetal hypoxia has been associated directly or indirectly with fetal programming of heart, brain, and kidney function and metabolism in adulthood. In this review, the role of hypoxia in fetal development, placentation, and fetal programming is summarized. Hypoxia is a basic mechanism involved in different pregnancy disorders and fetal health developmental complications. Although there are scientific data showing that hypoxia mediates changes in the growth trajectory of the fetus, modulates gene expression by epigenetic mechanisms, and determines the health status later in adulthood, more mechanistic studies are needed. Furthermore, if we consider that intrauterine hypoxia is not a rare event, and can be a consequence of unavoidable exposures to air pollution, nutritional deficiencies, obesity, and other very common conditions (drug addiction and stress), the health of future generations may be damaged and the incidence of some diseases will markedly increase as a consequence of disturbed fetal programming. Birth Defects Research 109:1377-1385, 2017.© 2017 Wiley Periodicals, Inc. © 2017 Wiley Periodicals, Inc.

  10. Maximizing Research and Development Resources: Identifying and Testing "Load-Bearing Conditions" for Educational Technology Innovations

    Science.gov (United States)

    Iriti, Jennifer; Bickel, William; Schunn, Christian; Stein, Mary Kay

    2016-01-01

    Education innovations often have a complicated set of assumptions about the contexts in which they are implemented, which may not be explicit. Education technology innovations in particular may have additional technical and cultural assumptions. As a result, education technology research and development efforts as well as scaling efforts can be…

  11. Tokamak first-wall coating program development

    International Nuclear Information System (INIS)

    Davis, M.J.; Langley, R.A.; Prevender, T.S.

    1977-08-01

    The development of a research program to study coatings for control of impurities originating from the first wall of a Tokamak reactor is extensively discussed. The first wall environment and sputtering, temperature, surface chemical, and bulk radiation damage effects are reviewed. Candidate materials and application techniques are discussed. The philosophy and flow chart of a recommended coating development plan are presented and discussed. Projected impacts of the proposed plan include benefits to other aspects of confinement experiments. A list of 45 references is appended

  12. Stable isotopes to detect food-conditioned bears and to evaluate human-bear management

    Science.gov (United States)

    Hopkins, John B.; Koch, Paul L.; Schwartz, Charles C.; Ferguson, Jake M.; Greenleaf, Schuyler S.; Kalinowski, Steven T.

    2012-01-01

    We used genetic and stable isotope analysis of hair from free-ranging black bears (Ursus americanus) in Yosemite National Park, California, USA to: 1) identify bears that consume human food, 2) estimate the diets of these bears, and 3) evaluate the Yosemite human–bear management program. Specifically, we analyzed the isotopic composition of hair from bears known a priori to be food-conditioned or non-food-conditioned and used these data to predict whether bears with an unknown management status were food-conditioned (FC) or non-food-conditioned (NFC). We used a stable isotope mixing model to estimate the proportional contribution of natural foods (plants and animals) versus human food in the diets of FC bears. We then used results from both analyses to evaluate proactive (population-level) and reactive (individual-level) human–bear management, and discussed new metrics to evaluate the overall human–bear management program in Yosemite. Our results indicated that 19 out of 145 (13%) unknown bears sampled from 2005 to 2007 were food-conditioned. The proportion of human food in the diets of known FC bears likely declined from 2001–2003 to 2005–2007, suggesting proactive management was successful in reducing the amount of human food available to bears. In contrast, reactive management was not successful in changing the management status of known FC bears to NFC bears, or in reducing the contribution of human food to the diets of FC bears. Nine known FC bears were recaptured on 14 occasions from 2001 to 2007; all bears were classified as FC during subsequent recaptures, and human–bear management did not reduce the amount of human food in the diets of FC bears. Based on our results, we suggest Yosemite continue implementing proactive human–bear management, reevaluate reactive management, and consider removing problem bears (those involved in repeated bear incidents) from the population.

  13. UCLA Translational Biomarker Development Program (UTBD)

    Energy Technology Data Exchange (ETDEWEB)

    Czernin, Johannes [Univ. of California, Los Angeles, CA (United States)

    2014-09-01

    The proposed UTBD program integrates the sciences of diagnostic nuclear medicine and (radio)chemistry with tumor biology and drug development. UTBD aims to translate new PET biomarkers for personalized medicine and to provide examples for the use of PET to determine pharmacokinetic (PK) and pharmacodynamic (PD) drug properties. The program builds on an existing partnership between the Ahmanson Translational Imaging Division (ATID) and the Crump Institute of Molecular Imaging (CIMI), the UCLA Department of Chemistry and the Division of Surgical Oncology. ATID provides the nuclear medicine training program, clinical and preclinical PET/CT scanners, biochemistry and biology labs for probe and drug development, radiochemistry labs, and two cyclotrons. CIMI provides DOE and NIH-funded training programs for radio-synthesis (START) and molecular imaging (SOMI). Other participating entities at UCLA are the Department of Chemistry and Biochemistry and the Division of Surgical Oncology. The first UTBD project focuses on deoxycytidine kinase, a rate-limiting enzyme in nucleotide metabolism, which is expressed in many cancers. Deoxycytidine kinase (dCK) positive tumors can be targeted uniquely by two distinct therapies: 1) nucleoside analog prodrugs such as gemcitabine (GEM) are activated by dCK to cytotoxic antimetabolites; 2) recently developed small molecule dCK inhibitors kill tumor cells by starving them of nucleotides required for DNA replication and repair. Since dCK-specific PET probes are now available, PET imaging of tumor dCK activity could improve the use of two different classes of drugs in a wide variety of cancers.

  14. Designing a leadership development program for surgeons.

    Science.gov (United States)

    Jaffe, Gregory A; Pradarelli, Jason C; Lemak, Christy Harris; Mulholland, Michael W; Dimick, Justin B

    2016-01-01

    Although numerous leadership development programs (LDPs) exist in health care, no programs have been specifically designed to meet the needs of surgeons. This study aimed to elicit practicing surgeons' motivations and desired goals for leadership training to design an evidence-based LDP in surgery. At a large academic health center, we conducted semistructured interviews with 24 surgical faculty members who voluntarily applied and were selected for participation in a newly created LDP. Transcriptions of the interviews were analyzed using analyst triangulation and thematic coding to extract major themes regarding surgeons' motivations and perceived needs for leadership knowledge and skills. Themes from interview responses were then used to design the program curriculum specifically to meet the leadership needs of surgical faculty. Three major themes emerged regarding surgeons' motivations for seeking leadership training: (1) Recognizing key gaps in their formal preparation for leadership roles; (2) Exhibiting an appetite for personal self-improvement; and (3) Seeking leadership guidance for career advancement. Participants' interviews revealed four specific domains of knowledge and skills that they indicated as desired takeaways from a LDP: (1) leadership and communication; (2) team building; (3) business acumen/finance; and (4) greater understanding of the health care context. Interviews with surgical faculty members identified gaps in prior leadership training and demonstrated concrete motivations and specific goals for participating in a formal leadership program. A LDP that is specifically tailored to address the needs of surgical faculty may benefit surgeons at a personal and institutional level. Copyright © 2016 Elsevier Inc. All rights reserved.

  15. Bearing structures

    International Nuclear Information System (INIS)

    Lee, A.S.; Preece, G.E.

    1988-01-01

    A hydrostatic bearing for the lower end of the vertical shaft of a sodium pump comprises a support shell encircling the shaft and a bush located between the shell and shaft. Liquid sodium is fed from the pump outlet to the bush/shaft and bush/shell interfaces to provide hydrostatic support. The bush outer surface and the shell inner surface are of complementary part-spherical shape and the bush floats relative to the shaft so that the bush can align itself with the shaft axis. Monitoring of the relative rotational speed of the bush with respect to the shaft (such rotation being induced by the viscous drag forces present) is also performed for the purposes of detecting abnormal operation of the bearing or partial seizure, at least one magnet is rotatable with the bush, and a magnetic sensor provides an output having a frequency related to the speed of the bush. (author)

  16. Foil bearing performance in liquid nitrogen and liquid oxygen

    Science.gov (United States)

    Genge, Gary G.; Saville, Marshall; Gu, Alston

    1993-01-01

    Space transfer vehicles and other power and propulsion systems require long-life turbopumps. Rolling-element bearings used in current turbopumps do not have sufficient life for these applications. Process fluid foil bearings have established long life, with exceptional reliability, over a wide range of temperatures and fluids in many high-speed turbomachinery applications. However, actual data on bearing performance in cryogenic fluids has been minimal. The National Aeronautics and Space Administration (NASA) and AlliedSignal Aerospace Systems and Equipment (ASE) have attempted to characterize the leaf-type compliant foil bearing in oxygen and nitrogen. The work performed under a joint internal research and development program between Marshall Space Flight Center (MSFC) and ASE demonstrated that the foil bearing has load capacities of at least 266 psi in liquid oxygen and 352 psi in liquid nitrogen. In addition, the bearing demonstrated a direct damping coefficient of 40 to 50 lb-sec/in. with a damping ratio of .7 to 1.4 in. liquid nitrogen using a bearing sized for upper-stage turbopumps. With the results from this testing and the years of successful use in air cycle machines and other applications, leaf-type compliant foil bearings are ready for testing in liquid oxygen turbopumps.

  17. Journal Bearings

    Directory of Open Access Journals (Sweden)

    Renato Brancati

    1999-01-01

    determined after acquiring and analysing the orbits described by the journal axis for assigned unbalance values in different operating conditions. Analysis of the results shows some particular operating features that were not entirely predicted by the theoretical model and which may give rise to malfunctions in the rotor-tilting pad bearings system. The tests were carried out in the rotor dynamics laboratory of the Dipartimento di Ingegneria Meccanica per l'Energetica at the University of Naples.

  18. Professional development for nuclear power programs in developing countries

    International Nuclear Information System (INIS)

    Kanter, M.A.

    1983-01-01

    Countries entering nuclear power programs for the first time find that inadequate planning for the development of trained manpower is a critical factor in the success of their programs. This requires the early training of a team for the planning and acquisition effort to be followed by training for the supervision of construction. In addition, there is the more readily recognized training for operation. Typical manpower needs for such projects have been documented by the International Atomic Energy Agency. The basic academic training of engineers and scientists, which should be available within the country; advanced academic training, which is often secured in institutions abroad; specialized training abroad by international agencies; specialized training by the vendors of nuclear equipment; and the development of indigenous training. This paper outlines all of these avenues but will concentrate on the training available through international agencies and on the development of indigenous training capability

  19. Camshaft bearing arrangement

    Energy Technology Data Exchange (ETDEWEB)

    Aoi, K.; Ozawa, T.

    1986-06-10

    A bearing arrangement is described for the camshaft of an internal combustion engine or the like which camshaft is formed along its length in axial order with a first bearing surface, a first cam lobe, a second bearing surface, a second cam lobe, a third bearing surface, a third cam lobe and a fourth bearing surface, the improvement comprising first bearing means extending around substantially the full circumference of the first bearing surface and journaling the first bearing surface, second bearing means extending around substantially less than the circumference of the second bearing surface and journaling the second bearing surface, third bearing means extending around substantially less than the circumference of the third bearing surface and journaling the third bearing surface, and fourth bearing means extending around substantially the full circumference of the fourth bearing surface and journaling the first bearing surface.

  20. A technology development summary for the AGT101 advanced gas turbine program

    Science.gov (United States)

    Boyd, Gary L.; Kidwell, James R.; Kreiner, Daniel M.

    1987-01-01

    A summary is presented of significant technology developments that have been made in the AGT101 advanced gas turbine program. The AGT101 design features are reviewed, and the power section testing and results are addressed in detail. The results of component testing and evaluation are described for the compressor, turbine, regenerator, and foil bearing. Ceramic component development is discussed, including that of the static seal, turbine shroud seal, regenerator shield planar seal, regenerator shield piston ring, stator rig, ceramic combustor, and turbine rotor. Important areas to be addressed by the Advanced Turbine Technology Applications Project now in the planning stage at DOE and NASA are briefly reviewed.

  1. Development of an effective valve packing program

    Energy Technology Data Exchange (ETDEWEB)

    Hart, K.A.

    1996-12-01

    Current data now shows that graphite valve packing installed within the guidance of a controlled program produces not only reliable stem sealing but predictable running loads. By utilizing recent technological developments in valve performance monitoring for both MOV`s and AOV`s, valve packing performance can be enhanced while reducing maintenance costs. Once known, values are established for acceptable valve packing loads, the measurement of actual valve running loads via the current MOV/AOV diagnostic techniques can provide indication of future valve stem sealing problems, improper valve packing installation or identify the opportunity for valve packing program improvements. At times the full benefit of these advances in material and predictive technology remain under utilized due to simple past misconceptions associated with valve packing. This paper will explore the basis for these misconceptions, provide general insight into the current understanding of valve packing and demonstrate how with this new understanding and current valve diagnostic equipment the key aspects required to develop an effective, quality valve packing program fit together. The cost and operational benefits provided by this approach can be significant impact by the: elimination of periodic valve repacking, reduction of maintenance costs, benefits of leak-free valve operation, justification for reduced Post Maintenance Test Requirements, reduced radiation exposure, improved plant appearance.

  2. Overview of Japanese control rods development program

    International Nuclear Information System (INIS)

    Koyama, M.

    1984-01-01

    The Japanese control rods development program was established based on the fast breeder reactor program. Therefore, PNC's efforts have been made mainly for the development of analysis, design and fabrication technologies for ''JOYO'' and ''MONJU'' control rods. Laboratory studies were performed to obtain the information for absorber materials. The design and fabrication of the sealed and vented type control rod pins were completed, and water loop tests and in-sodium tests were carried out. Irradiation behavior of enriched B 4 C pellets with low and high density in DFR was examined. Japan's experimental fast reactor, JOYO, has been operated at the rated power of 50MWt and 75MWt since April 1977 when the MK-I core (breeder core) attained initial criticality. Post irradiation examinations on control rod, removed from the reactor, were carried out and their performance behavior were evaluated. In the MK-II core, a control rods monitoring program has been in investigation. Absorber Materials Irradiation Rigs (AMIR) are scheduled to be loaded and irradiated in the JOYO MK-II core from 1984. (author)

  3. Research and development program, fiscal year 1970

    Energy Technology Data Exchange (ETDEWEB)

    1968-04-01

    The biomedical program of the Laboratory of Nuclear Medicine and Radiation Biology for FY 1970 is conducted within the scope of the following categories: Somatic Effects of Radiation; Combating Detrimental Effects of Radiation; Molecular and Cellular Level Studies; Environmental Radiation Studies; Radiological and Health Physics and Instrumentation; Cancer Research; and Selected Beneficial Applications. The overall objectives of the Laboratory within these areas of the Biology and Medicine Program may be summarized as follows: (1) investigation of the effects of ionizing radiation on systems of biological significance and on living organisms; (2) assessment and study of the immediate and long term consequences of the environmental radioactivity on flora, fauna, and man; (3) development of beneficial uses of ionizing radiation and radioactive substances in medicine and biology; and (4) the conduct of training and educational activities in fields related to the biological and medical aspects of radiation.

  4. Developing solar power programs : San Francisco's experience

    International Nuclear Information System (INIS)

    Schwartz, F.

    2006-01-01

    This keynote address discussed an array of solar programs initiated in government-owned buildings in San Francisco. The programs were strongly supported by the city's mayor,and the voting public. Known for its fog and varying microclimates, 11 monitoring stations were set up throughout the city to determine viable locations for the successful application of solar technologies. It was observed that 90 per cent of the available sunshine occurred in the central valley, whereas fog along the Pacific shore was problematic. Seven of the monitoring sites showed excellent results. Relationships with various city departments were described, as well as details of study loads, load profiles, electrical systems, roofs and the structural capabilities of the selected government buildings. There was a focus on developing good relations with the local utility. The Moscone Convention Center was selected for the program's flagship installation, a 675 kW solar project which eventually won the US EPA Green Power Award for 2004 and received high press coverage. Cost of the project was $4.2 million. 825,000 kWh solar electricity was generated, along with 4,500,000 kWh electricity saved annually from efficiency measures, resulting in a net reduction of 5,325,000 kWh. Savings on utilities bills for the center were an estimated $1,078,000. A pipeline of solar projects followed, with installations at a sewage treatment plant and a large recycling depot. A program of smaller sites included libraries, schools and health facilities. Details of plans to apply solar technology to a 500 acre redevelopment site in southeast San Francisco with an aging and inadequate electrical infrastructure were described. A model of efficient solar housing for the development was presented, with details of insulation, windows, heating ventilation and air-conditioning (HVAC), water heating, lighting, appliances and a 1.2 kilowatt solar system. Peak demand reductions were also presented. tabs., figs

  5. Intravenous maternal -arginine administration to twin-bearing ewes during late pregnancy enhances placental growth and development.

    Science.gov (United States)

    van der Linden, D S; Sciascia, Q; Sales, F; Wards, N J; Oliver, M H; McCoard, S A

    2015-10-01

    This study aimed to investigate if intravenous maternal Arg administration to well-fed twin-bearing ewes, from 100 to 140 d of gestation or birth, could enhance placental development and placental nutrient transport. Ewes received intravenous infusions of saline (control) or 345 μmol Arg HCl/kg of BW 3 times daily from d 100 of pregnancy (P100) to d 140 of pregnancy (P140; cohort 1) or from P100 to birth (cohort 2). At P140, ewes in cohort 1 were euthanized and individual placentae per fetus were dissected and placentomes were classed per type (A to D) and size (light to heavy). Placentome number and individual weight were recorded. As an indicator of placental nutrient transport, blood plasma was collected from the uterine ovarian vein (UOV), uterine artery (UA), and umbilical vein and artery at the time of euthanasia and analyzed for metabolites and free AA concentrations. The ewes in cohort 2 were allowed to lamb and lambs were weighed at birth. The expelled placenta was dissected and number of cotyledons and weights of total cotyledons, remaining fetal membranes, and total placenta were recorded. At P140, Arg-infused ewes had a 63% ( = 0.03) greater number of unoccupied caruncles than control ewes. No differences were observed for placental weight at P140. At birth, lambs from Arg-infused ewes tended to have 11% ( = 0.09) greater placental weight and 34% ( = 0.03) greater total cotyledon weight compared with control lambs. Arginine-infused ewes (Arg-infused) had increased concentrations of Arg ( = 0.0001) and ornithine (Orn; = 0.004) but decreased concentrations of Met ( = 0.01) and His ( = 0.02 and = 0.09, respectively) compared with control ewes in plasma UOV and UA. Fetuses from Arg-infused ewes had increased concentrations of Orn ( = 0.005) and decreased concentrations of His ( = 0.006), Met ( = 0.003), and Lys ( = 0.01) but no differences in Arg ( > 0.10) concentrations were found compared with control fetuses in umbilical artery and vein plasma. This

  6. The impact of teaching development programs

    DEFF Research Database (Denmark)

    Rump, Camilla Østerberg; Christiansen, Frederik V; Trigwell, Keith

    ), and the development of teachers’ self-efficacy beliefs with respect to teaching (as measured by a modified version of the Science Teaching Efficacy Belief Instrument). We find significant improvements with respect to both of these dimensions in several recent courses. No significant changes are found with respect...... to the Information Transfer Teacher Focus of the ATI or the outcome expectancy beliefs of STEBI. The paper discusses which elements of our course design we think are conducive for the development of teacher self-efficacy beliefs and conceptual change student focus respectively, and presents a model for relating......University teaching development programs for academic staff typically have a range of different educational goals, ranging from gaining basic proficiency in teaching to the more fundamental goal of changing teachers’ conception of teaching towards student focused conceptions. In the current paper...

  7. Development and Characterization of Novel Floating-Mucoadhesive Tablets Bearing Venlafaxine Hydrochloride

    Directory of Open Access Journals (Sweden)

    Raghvendra Misra

    2016-01-01

    Full Text Available The present investigation is concerned about the development of floating bioadhesive drug delivery system of venlafaxine hydrochloride which after oral administration exhibits a unique combination of floating and bioadhesion to prolong gastric residence time and increase drug bioavailability within the stomach. The floating bioadhesive tablets were prepared by the wet granulation method using different ratios of hydroxypropyl methyl cellulose (HPMC K4MCR and Carbopol 934PNF as polymers. Sodium bicarbonate (NaHCO3 and citric acid were used as gas (CO2 generating agents. Tablets were characterized for floating properties, in vitro drug release, detachment force, and swelling index. The concentration of hydroxypropyl methyl cellulose and Carbopol 934PNF significantly affects the in vitro drug release, floating properties, detachment force, and swelling properties of the tablets. The optimized formulation showed the floating lag time 72±2.49 seconds and duration of floating 24.50±0.74 hr. The in vitro release studies and floating behavior were studied in simulated gastric fluid (SGF at pH 1.2. Different drug release kinetics models were also applied. The in vitro drug release from tablets was sufficiently sustained (more than 18 hr and the Fickian transports of the drug from the tablets were confirmed. The radiological evidence suggests that the tablets remained buoyant and altered position in the stomach of albino rabbit and mean gastric residence time was prolonged (more than > 6 hr.

  8. Histology and histochemistry of the gekkotan notochord and their bearing on the development of notochordal cartilage.

    Science.gov (United States)

    Jonasson, Kristin A; Russell, Anthony P; Vickaryous, Matthew K

    2012-06-01

    The persistence of the notochord into the skeletally mature life stage is characteristic of gekkotans, but is otherwise of rare occurrence among amniotes. The taxonomic diversity of Gekkota affords the opportunity to investigate the structure and development of this phylogenetically ancestral component of the skeleton, and to determine its basic characteristics. The gekkotan notochord spans almost the entire postcranial long axis and is characterized by a moniliform morphology with regularly alternating zones of chordoid and chondroid tissue. Chordoid tissue persists in the region of intervertebral articulations and occupies the cavitations that lie between the centra of the amphicoelous vertebrae. Chondroid tissue is restricted to zones in which the diameter of the notochord is reduced, corresponding to mid-vertebral locations. In the tail, these zones of chondroid tissue are associated with the autotomic fracture planes. Chondroid tissue first manifests during late embryogenesis, appears to differentiate from pre-existing chordoid tissue, and has the histological and histochemical characteristics of cartilage. Our observations lend support to the hypothesis that cartilage can be derived directly from notochordal tissue, and suggest that the latter may be an evolutionary and developmental precursor to chordate cartilage. The persistence of chordoid tissue in the intervertebral regions of amphicoelous vertebrae is consistent with a suite of paedomorphic traits exhibited by gekkotans and suggests that the typical hydrostatic nature of notochordal tissue may play a role in mechanically governing patterns of displacement between adjacent amphicoelous vertebrae that lack extensive centrum-to-centrum contact. Copyright © 2012 Wiley Periodicals, Inc.

  9. Mixed Waste Integrated Program emerging technology development

    Energy Technology Data Exchange (ETDEWEB)

    Berry, J.B. [Oak Ridge National Lab., TN (United States); Hart, P.W. [USDOE, Washington, DC (United States)

    1994-06-01

    The US Department of Energy (DOE) is responsible for the management and treatment of its mixed low-level wastes (MLLW). MLLW are regulated under both the Resource Conservation and Recovery Act and various DOE orders. Over the next 5 years, DOE will manage over 1.2 m{sup 3} of MLLW and mixed transuranic (MTRU) wastes. In order to successfully manage and treat these mixed wastes, DOE must adapt and develop characterization, treatment, and disposal technologies which will meet performance criteria, regulatory approvals, and public acceptance. Although technology to treat MLLW is not currently available without modification, DOE is committed to developing such treatment technologies and demonstrating them at the field scale by FY 1997. The Office of Research and Development`s Mixed Waste Integrated Program (MWIP) within the DOE Office of Environmental Management (EM), OfFice of Technology Development, is responsible for the development and demonstration of such technologies for MLLW and MTRU wastes. MWIP advocates and sponsors expedited technology development and demonstrations for the treatment of MLLW.

  10. Research and development program, fiscal year 1966

    Energy Technology Data Exchange (ETDEWEB)

    1964-04-01

    The biomedical program of the Laboratory of Nuclear Medicine and Radiation Biology for FY 1966 is conducted within the scope of the following categories: Somatic Effects of Radiation; Combating Detrimental Effects of Radiation; Molecular and Cellular Level Studies; Environmental Radiation Studies; Radiological and Health Physics and Instrumentation; Chemical Toxicity; Cancer Research; and Selected Beneficial Applications. The overall objectives of the Laboratory within these areas of the Biology and Medicine program may be summarized as follows: (1) investigation of the effects of ionizing radiation on living organisms and systems of biological significance; (2) investigation of the dynamic aspects of physiological and biochemical processes in man, animals and plants and how these processes are modified by radiation and related pathological states; (3) the assessment and study of the immediate and long term consequences of the operation or detonation of nuclear devices on the fauna, and flora in man's environment and on man; (4) the development of methods of minimizing or preventing the detrimental effects of ionizing radiation; (5) research in, and development of, beneficial uses of ionizing radiation and radioactive substances in medicine and biology; (6) research in the development of new and more efficient radiation detection devices; (7) research, including field studies, as mutually agreed upon by the Commission and the University, in connection with the conduct of weapon tests and biomedical and civil effects experiments at such tests conducted at continental and overseas test sites; and (8) the conduct of training and educational activities in the biological and medical aspects of radiation and related fields.

  11. French development program on fuel cycle

    International Nuclear Information System (INIS)

    Viala, M.; Bourgeois, M.

    1991-01-01

    The need to close the fuel cycle of fast reactors makes the development of the cycle installations (fuel fabrication, irradiated assembly conditioning before reprocessing, reprocessing and waste management) especially independent with the development of the reactor. French experience with the integrated cycle over a period of about 25 years, the tonnage of fuels fabricated (more than 100 t of mixed oxides) for the Rapsodie, Phoenix and SuperPhoenix reactors, and the tonnage of reprocessed fuel (nearly 30 t of plutonium fuel) demonstrate the control of the cycle operations. The capacities of the cycle installations in existence and under construction are largely adequate for presents needs, even including a new European EFR reactor. They include the Cadarache fuel fabrication complex, the La Hague UP2-800 reprocessing plant, and the Marcoule pilot facility. Short- and medium-term R and D programs are connected with fuel developments, with the primary objective of very high burnups. For the longer term and for a specific plant to reprocess fast reactor fuels, the programs could concern new fabrication and reprocessing systems and the study of the consequences of the reduction in fuel out-of-core time

  12. Program Leader, Think Tank Initiative | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... (i.e. senior management) on issues of program and project development and ... Ensures that a regional perspective is brought to bear on program planning at ... projects between Canadian and developing country researchers; and; When ...

  13. Development of model hydroxyapatite bone scaffolds with multiscale porosity for potential load bearing applications

    Science.gov (United States)

    Dellinger, Jennifer Gwynne

    2005-11-01

    Model hydroxyapatite (HA) bone scaffolds consisting of a latticed pattern of rods were fabricated by a solid freeform fabrication (SFF) technique based on the robotic deposition of colloidal pastes. An optimal HA paste formulation for this method was developed. Local porosity, i.e. microporosity (1--30 mum) and sintering porosity (less than 1 mum), were produced by including polymer microsphere porogens in the HA pastes and by controlling the sintering of the scaffolds. Scaffolds with and without local porosity were evaluated with and without in vitro accelerated degradation. Percent weight loss of the scaffolds and calcium and phosphorus concentrations in solution increased with degradation time. After degradation, compressive strength and modulus decreased significantly for scaffolds with local porosity, but did not change significantly for scaffolds without local porosity. The compressive strength and modulus of scaffolds without local porosity were comparable to human cortical bone and were significantly greater than the scaffolds with local porosity. Micropores in HA disks caused surface pits that increased the surface roughness as compared to non-microporous HA disks. Mouse mesenchymal stem cells extended their cell processes into these microporous pits on HA disks in vitro. ALP expression was prolonged, cell attachment strength increased, and ECM production appeared greater on microporous HA disks compared to non-microporous HA disks and tissue culture treated polystyrene controls. Scaffolds with and without microporosity were implanted in goats bones. Microporous scaffolds with rhBMP-2 increased the percent of the scaffold filled with bone tissue compared to microporous scaffolds without rhBMP-2. Lamellar bone inside scaffolds was aligned near the rods junctions whereas lamellar bone was aligned in a more random configuration away from the rod junctions. Microporous scaffolds stained darkly with toluidine blue beneath areas of contact with new bone. This

  14. Tested program for Third World economic development

    Energy Technology Data Exchange (ETDEWEB)

    Lindholm, R.W.

    1977-04-01

    Some of the responsibility for the inability of Western-oriented Third World Countries (1) to make democratic economic institutions work rests upon advisers to American and international financial institutions who recommend principles of economic growth distilled out of Keynesian recipes for an over-saving Western society of the 1930s, and out of aspects of American experience with no applicability elsewhere. Applicable aspects of U.S. experience suggest a program relying on capitalistic drives and using fiscal and monetary policy of the type that proved useful in the development of democratic capitalism in the U.S. in the 19th century.

  15. Oracle PLSQL Programming A Developer's Workbook

    CERN Document Server

    Feuerstein, Steven

    2008-01-01

    However excellent they are, most computer books are inherently passive--readers simply take in text without having any opportunity to react to it. The Oracle PL/SQL Developer's Workbook is a different kind of animal! It's designed to engage you actively, to get you solving programming problems immediately, and to help you apply what you've learned about PL/SQL--and in the process deepen your knowledge of the language. By tackling the exercises in this workbook, you'll find yourself moving more rapidly along the learning curve to join the growing ranks of PL/SQL experts. The Oracle PL/SQL

  16. Standard Review Plan Update and Development Program

    International Nuclear Information System (INIS)

    1992-05-01

    This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures

  17. Standard Review Plan Update and Development Program

    Energy Technology Data Exchange (ETDEWEB)

    1992-05-01

    This implementing procedures document (IPD) was prepared for use in implementing tasks under the standard review plan update and development program (SRP-UDP). The IPD provides comprehensive guidance and detailed procedures for SRP-UDP tasks. The IPD is mandatory for contractors performing work for the SRP-UDP. It is guidance for the staff. At the completion of the SRP-UDP, the IPD will be revised (to remove the UDP aspects) and will replace NRR Office Letter No. 800 as long-term maintenance procedures.

  18. Duplex tube steam reformer development program

    International Nuclear Information System (INIS)

    Lewe, C.K.; Nieto, J.M.; Papadopoulos, A.

    1978-09-01

    Work done in partial fulfillment of Task 7 of the Duplex Steam Reformer Development Program is described. The DSR concept acts as a double barrier between a process heat high temperature reactor plant (PNP) and a closed loop chemical heat pipe (CHP) for the long distance transport of chemical energy to a remote industrial user. The current state of the DSR design is described as well as related systems and equipment. The PNP concept presented is based upon work currently underway in the Federal Republic of Germany

  19. Mixed Waste Integrated Program emerging technology development

    International Nuclear Information System (INIS)

    Berry, J.B.; Hart, P.W.

    1994-01-01

    The US Department of Energy (DOE) is responsible for the management and treatment of its mixed low-level wastes (MLLW). MLLW are regulated under both the Resource Conservation and Recovery Act and various DOE orders. Over the next 5 years, DOE will manage over 1.2 m 3 of MLLW and mixed transuranic (MTRU) wastes. In order to successfully manage and treat these mixed wastes, DOE must adapt and develop characterization, treatment, and disposal technologies which will meet performance criteria, regulatory approvals, and public acceptance. Although technology to treat MLLW is not currently available without modification, DOE is committed to developing such treatment technologies and demonstrating them at the field scale by FY 1997. The Office of Research and Development's Mixed Waste Integrated Program (MWIP) within the DOE Office of Environmental Management (EM), OfFice of Technology Development, is responsible for the development and demonstration of such technologies for MLLW and MTRU wastes. MWIP advocates and sponsors expedited technology development and demonstrations for the treatment of MLLW

  20. Louisiana's oil spill program : new developments

    International Nuclear Information System (INIS)

    Debusschere, K.; Tedford, R.; Brolin, J.; Lorentz, W.

    2000-01-01

    The Louisiana Oil Spill Coordinator's Office (LOSCO) was established to improve oil spill response, spill prevention and coordination. Louisiana is challenged with having the highest exposure of oil spills because a large portion of its economy is based on oil and gas exploration and production. LOSCO will find ways to minimize the risk of unauthorized oil spills and will address damage assessment and restoration efforts. The aging oil and gas infrastructure in Louisiana has also been recognized as a potential major source for oil spills. LOSCO locates potential spill locations and assesses the risks associated with the sites, some of which are 100 years old. LOSCO also initiated the following two programs: (1) the Abandoned Barge Program initiated in 1993 to remove abandoned barges that pose a high risk for oil discharge, and (2) the Abandoned Non-Hazardous Oil Waste (NOW) Pit and Facility Program initiated in 1992 to locate and remove structures, pits and wells that pose a risk for oil spills. About 25,000 facilities, pits, sumps and reservoirs have been inventoried and evaluated to determine if they pose a risk to human health or the environment. The Louisiana Oil Spill Prevention and Response Act (OSPRA) of 1991 allocates up to $2 million per year for the abatement of oil spills from abandoned facilities in Louisiana. The state legislature has also created the Applied and Educational Oil Spill Research and Development Program (OSRADP) to fund oil spill research. Since 1993, OSRADP has granted 68 awards in support of 42 projects, many of which focused on recovery and cleanup methods including in-situ burning, fate and effect of oil in Louisiana environments, bioremediation, phytoremediation, composting, chemical cleaners, dispersants, sorbents, and solidifiers. 3 refs., 1 tab

  1. Interagency cooperation in the development of a cost-effective transportation and disposal solution for vitrified radium bearing material

    International Nuclear Information System (INIS)

    Smith, M.L.; Nixon, D.A.; Stone, T.J.; Tope, W.G.; Vogel, R.A.; Allen, R.B.; Schofield, W.D.

    1996-01-01

    Fernald radium bearing ore residue waste, stored within Silos 1 and 2 (K-65) and Silo 3 waste, will be vitrified for disposal at the Nevada Test Site (NTS). A comprehensive, parametric evaluation of waste form, shielding requirements, packaging, and transportation alternatives was completed to identify the safest, most cost-effective approach. The impacts of waste loading, waste form, regulatory requirements, NTS waste acceptance criteria, as-low-as-resonably-achievable principles, and material handling costs were factored into the recommended approach. Through cooperative work between the U.S. Department of Energy (DOE) and the U.S. Department of Transportation (DOT), the vitrified K-65 and Silo 3 radioactive material will be classified consistent with the regulations promulgated by DOT in the September 28, 1995 Federal Register. These new regulations adopt International Atomic Energy Agency language to promote a consistent approach for the transportation and management of radioactive material between the international community and the DOT. Use of the new regulations allows classification of the vitrified radioactive material from the Fernald silos under the designation of low specific activity-II and allows the development of a container that is optimized to maximize payload while minimizing internal void space, external surface radiation levels, and external volume. This approach minimizes the required number of containers and shipments, and the related transportation and disposal costs

  2. Interagency cooperation in the development of a cost-effective transportation and disposal solution for vitrified radium bearing material

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.L.; Nixon, D.A.; Stone, T.J.; Tope, W.G.; Vogel, R.A. [Fernald Environmental Restoration Management Corp., Cincinnati, OH (United States); Allen, R.B. [USDOE, Fernald Area Office, Cincinnati, OH (United States); Schofield, W.D. [Foster Wheeler Environmental Corp. (United States)

    1996-02-01

    Fernald radium bearing ore residue waste, stored within Silos 1 and 2 (K-65) and Silo 3 waste, will be vitrified for disposal at the Nevada Test Site (NTS). A comprehensive, parametric evaluation of waste form, shielding requirements, packaging, and transportation alternatives was completed to identify the safest, most cost-effective approach. The impacts of waste loading, waste form, regulatory requirements, NTS waste acceptance criteria, as-low-as-resonably-achievable principles, and material handling costs were factored into the recommended approach. Through cooperative work between the U.S. Department of Energy (DOE) and the U.S. Department of Transportation (DOT), the vitrified K-65 and Silo 3 radioactive material will be classified consistent with the regulations promulgated by DOT in the September 28, 1995 Federal Register. These new regulations adopt International Atomic Energy Agency language to promote a consistent approach for the transportation and management of radioactive material between the international community and the DOT. Use of the new regulations allows classification of the vitrified radioactive material from the Fernald silos under the designation of low specific activity-II and allows the development of a container that is optimized to maximize payload while minimizing internal void space, external surface radiation levels, and external volume. This approach minimizes the required number of containers and shipments, and the related transportation and disposal costs.

  3. Development of ball bearing in high temperature water for in-vessel type control rod drive mechanism of advanced marine reactor

    Energy Technology Data Exchange (ETDEWEB)

    Nunokawa, Hiroshi [Mitsubishi Heavy Industries, Ltd., Tokyo (Japan); Yoritsune, Tsutomu; Imayoshi, Shou; Ochiai, Masa-aki; Ishida, Toshihisa [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment; Kasahara, Yoshiyuki [Advanced Reactor Technology Co., Ltd., Tokyo (Japan)

    2001-06-01

    An advanced marine reactor MRX designed by Japan Atomic Energy Research Institute (JAERI) adopts an in-vessel type control rod drive mechanism, which is installed inside the reactor vessel. Since the in-vessel type control rod drive mechanism should work at a severe condition of a high temperature and high pressure water - 310degC and 12 MPa -, the JAERI has developed the components, a ball bearing of which especially is one of key technologies for realization of this type mechanism. The present report describes the development of the ball bearing containing a survey of materials, material screening tests on oxidation in an autoclave and rolling wear by a small facility, a trial fabrication of the full size ball bearing, and endurance test of it in the high temperature water. As a result, it was found from the development that the materials of cobalt alloy for both of the inner and outer races, cermet for the ball, and graphite for the retainer can satisfy the design condition of the ball bearing. (author)

  4. Groundwater-quality data in the Bear Valley and Selected Hard Rock Areas study unit, 2010: Results from the California GAMA Program

    Science.gov (United States)

    Mathany, Timothy M.; Belitz, Kenneth

    2013-01-01

    Groundwater quality in the 112-square-mile Bear Valley and Selected Hard Rock Areas (BEAR) study unit was investigated by the U.S. Geological Survey (USGS) from April to August 2010, as part of the California State Water Resources Control Board (SWRCB) Groundwater Ambient Monitoring and Assessment (GAMA) Program’s Priority Basin Project (PBP). The GAMA-PBP was developed in response to the California Groundwater Quality Monitoring Act of 2001 and is being conducted in collaboration with the SWRCB and Lawrence Livermore National Laboratory (LLNL). The BEAR study unit was the thirty-first study unit to be sampled as part of the GAMA-PBP. The GAMA Bear Valley and Selected Hard Rock Areas study was designed to provide a spatially unbiased assessment of untreated-groundwater quality in the primary aquifer system and to facilitate statistically consistent comparisons of untreated groundwater quality throughout California. The primary aquifer system is defined as the zones corresponding to the perforation intervals of wells listed in the California Department of Public Health (CDPH) database for the BEAR study unit. Groundwater quality in the primary aquifer system may differ from the quality in the shallow or deep water-bearing zones; shallow groundwater may be more vulnerable to surficial contamination. In the BEAR study unit, groundwater samples were collected from two study areas (Bear Valley and Selected Hard Rock Areas) in San Bernardino County. Of the 38 sampling sites, 27 were selected by using a spatially distributed, randomized grid-based method to provide statistical representation of the primary aquifer system in the study unit (grid sites), and the remaining 11 sites were selected to aid in the understanding of the potential groundwater-quality issues associated with septic tank use and with ski areas in the study unit (understanding sites). The groundwater samples were analyzed for organic constituents (volatile organic compounds [VOCs], pesticides and

  5. Improved remote HEPA filtration development program

    International Nuclear Information System (INIS)

    Wilson, C.E. III.

    1987-03-01

    This paper presents a summary of the prototype development and hot cell mock-up testing program undertaken to adapt a commercial remote HEPA filter housing for use in the Process Facility Modification Project (PFMP). This program was initiated in response to the project design criteria and documentation that required the air from the hot cell environment to be exhausted through three stages of HEPA filtration. Due to the anticipated quantity of radioactive contamination captured by the first stage of filters, it was determined that the first stage would need to be located in a remotely operated and maintained shielded cell adjoining the primary hot cell areas. Commercially available remote filtration equipment was evaluated and candidate unit was identified, which could be developed into a suitable filter housing. A candidate unit was obtained from Flanders Filters, Inc. and a series of hot cell mock-up tests were identified in the 305 facility at the Hanford site. The results of these tests, and further interaction with the vendor, led to a prototype remote filter housing which satisfied most PFMP criteria and proved to be significantly superior to existing commercial units for remote operation/maintenance

  6. Utility oversight of Cask System Development Program

    International Nuclear Information System (INIS)

    Vincent, J.A.; Jordan, J.M.; Schwartz, M.H.

    1993-01-01

    This paper will present the electric utility industry's perspective on the status and scope of the DOE's Office of Civilian Radioactive Waste Management's (DOE/OCRWM) transportation cask systems development activities, including the Cask Systems Development Program (CSDP) Initiative I transportation cask projects. This presentation is particularly timely because the CSDP Independent Management Review Group (IMRG), os which one of the authors is a member, completed an objective assessment of OCRWM's transportation cask system development activities and issued its first report in late August 1992. The perspective on these cask systems development activities that will be presented reflects conclusions based on (1) the industry's review of CSDP Preliminary and Draft Final Design Reports for the Initiative I cask projects, (2) the activities of one of the authors as a member of the IMRG, and (3) the positions that the industry has consistently taken on what it believes to be the appropriate scope and pace of the CSDP and its integration with other OCRWM activities. Background information on the OCRWM transportation cask systems development activities and the relevant industry activities will also be provided

  7. The low-enrichment fuel development program

    International Nuclear Information System (INIS)

    Stahl, D.

    1993-01-01

    In the 1950s and 1960s, low-power research reactors were built around the world utilized MTR-type fuel elements containing 20% enriched uranium. However, the demand for higher specific power created a need for greater uranium-235 concentrations. Early difficulties in increasing uranium content led to the substitution of highly enriched uranium in place of the 20% enriched fuel previously utilized. The highly enriched material also yielded other benefits including longer core residence time, higher specific reactivity, and somewhat lower cost. Highly enriched material then became readily available and was used for high-power reactors as well as in low-power reactors where 20% enriched material would have sufficed. The trend toward higher and higher specific power also led to the development of the dispersion-type fuels which utilized highly enriched uranium at a concentration of about 40 wt%. In the 1970's, however, concerns were raised about the proliferation resistance of fuels and fuel cycles. As a consequence, the U.S. Department of State has recently prohibited the foreign shipment of highly enriched material, except where prior contractual obligation or special merit exists. This will impact on the availability and utilization of highly enriched uranium for research and test reactor fuel. It has also stimulated development programs on fuels with higher uranium content which would allow the use of uranium of lower enrichment. The purpose of this report is to briefly describe the overall fuel-development program which is coordinated by Argonne National Laboratory for the Department of Energy, and to indicate the current and potential uranium loadings. Other reports will address the individual fuel-development activities in greater detail

  8. Building Technologies Program Multi-Year Program Plan Research and Development 2008

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2008-01-01

    Building Technologies Program Multi-Year Program Plan 2008 for research and development, including residential and commercial integration, lighting, HVAC and water heating, envelope, windows, and analysis tools.

  9. Development of robotic program: an Asian experience.

    Science.gov (United States)

    Sahabudin, R M; Arni, T; Ashani, N; Arumuga, K; Rajenthran, S; Murali, S; Patel, V; Hemal, A; Menon, M

    2006-06-01

    Robotic surgery was started in the Department of Urology, Hospital Kuala Lumpur, in April 2004. We present our experience in developing the program and report the results of our first 50 cases of robotic radical prostatectomy. A three-arm da Vinci robotic system was installed in our hospital in March 2004. Prior to installation, the surgeons underwent training at various centers in the United States and Paris. The operating theatre was renovated to house the system. Subsequently, the initial few cases were done with the help of proctors. Data were prospectively collected on all patients who underwent robot-assisted radical prostatectomy for localized carcinoma of the prostate. Fifty patients underwent robot assisted radical prostatectomy from March 2004 to June 2005. Their ages ranged from 52 to 75 years, (average age 60.2 years). PSA levels ranged from 2.5 to 35 ng/ml (mean 10.6 ng/ml). Prostate volume ranged from 18 to 130 cc (average 32.4 cc). Average operating time for the first 20 cases was 4 h and for the next 30 cases was 2.5 h. Patients were discharged 1-3 days post-operatively. Catheters were removed on the fifth day following a cystogram. The positive margin rate as defined by the presence of cancer cells at the inked margin was 30%. Twenty-one patients had T1c disease and one had T1b on clinical staging. Of these, two were apical margin positive. Twenty-six patients had T2 disease and eight of them were apical margin positive. Two patients had T3 disease, one of whom was apical margin positive. Five patients (10%) had PSA recurrence. Five patients had a poorly differentiated carcinoma and the rest had Gleason 6 or 7. Eighty percent of the patients were continent on follow-up at 3 months. Of those who were potent before the surgery, 50% were potent at 3-6 months. The robotic surgery program was successfully implemented at our center on the lines of a structured program, developed at Vattikuti Urology Institute (VUI). We succeeded in creating a team and

  10. Polymer OLED White Light Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Homer Antoniadis; Vi-En Choong; Stelios Choulis; Brian Cumpston; Rahul Gupta; Mathew Mathai; Michael Moyer; Franky So

    2005-12-19

    OSRAM Opto Semiconductors (OSRAM) successfully completed development, fabrication and characterization of the large area, polymer based white light OLED prototype at their OLED Research and Development (R&D) facility in San Jose, CA. The program, funded by the Department of Energy (DOE), consisted of three key objectives: (1) Develop new polymer materials and device architectures--in order to improve the performance of organic light emitters. (2) Develop processing techniques--in order to demonstrate and enable the manufacturing of large area, white light and color tunable, solid state light sources. (3) Develop new electronics and driving schemes for organic light sources, including color-tunable light sources. The key performance goals are listed. A world record efficiency of 25 lm/W was established for the solution processed white organic device from the significant improvements made during the project. However, the challenges to transfer this technology from an R&D level to a large tile format such as, the robustness of the device and the coating uniformity of large area panels, remain. In this regard, the purity and the blend nature of the materials are two factors that need to be addressed in future work. During the first year, OSRAM's Materials and Device group (M&D) worked closely with the major polymer material suppliers to develop the polymer emissive technology. M&D was successful in demonstrating a 7-8 lm/W white light source which was based on fluorescent materials. However, it became apparent that the major gains in efficiency could only be made if phosphorescent materials were utilized. Thus, in order to improve the performance of the resulting devices, the focus of the project shifted towards development of solution-processable phosphorescent light emitting diodes (PHOLEDs) and device architectures. The result is a higher efficiency than the outlined project milestone.

  11. Groundwater quality assessment for the Bear Creek hydrogeologic regime at the Y-12 Plant, 1990: Data interpretations and proposed program modifications

    International Nuclear Information System (INIS)

    1991-06-01

    This report is a detailed assessment of groundwater quality at several hazardous waste-management facilities associated with the Department of Energy (DOE) Y-12 Plant in Oak Ridge, Tennessee. The sites are located in an area defined as the Bear Creek Hydrogeologic Regime (BCHR), which is one of three hydrogeologic regimes that have been defined at the Y-12 Plant in an effort to unify and coordinate site-specific monitoring activities for planning and reporting purposes. Section 2.0 contains background information regarding the monitored sites and a discussion of the program objectives. An overview of the complex hydrogeologic system in the BCHR is provided in Section 3.0. A discussion of the interpretive assumptions used in evaluating the 1990 assessment data, a review of groundwater geochemistry and background water quality, detailed descriptions of groundwater contaminant plumes, and a discussion regarding the quality of groundwater and surface water exiting the BCHR are presented in Section 4.0. Findings of the 1990 assessment program are summarized in Section 5.0. Modification to the assessment monitoring program proposed for 1991 are in Section 6.0, and a list of references (Section 7.0) concludes the report. 20 refs., 23 figs., 12 tabs

  12. Seismic isolation development for the US advanced liquid-metal reactor program

    International Nuclear Information System (INIS)

    Gluekler, E.L.; Bigelow, C.C.; DeVita, V.; Kelly, J.M.; Seidensticker, R.W.; Tajirian, F.F.

    1991-01-01

    GE Nuclear Energy, in association with a US Industrial Team and support from the US National Laboratories and Universities, is developing a modular liquid-metal reactor concept for the US DOE. The objective of this development is to provide, by the turn of the century, a reactor with optimized passive safety features that is economically competitive with other domestic energy sources, licensable, and ready for commercial deployment. One of the unique features of the concept is the seismic isolation of the reactor modules which decouples the reactors and their safety systems from potentially damaging ground motions and significantly enhances the structural resistance to high energy, as well as long-duration earthquakes. Seismic isolation is accomplished with high-damping natural-rubber bearings. The reactors are located in individual silos below grade level and are supported by the isolator bearings at approximately their center of gravity. This application of seismic isolation is the first for a US nuclear power plant. A development program has been established to assure the full benefits from the utilization of this new approach and to provide adequate system characterization and qualification for licensing certification. The development program, which is supported by the US DOE, ANL, Energy Technology Engineering Center (ETEC), the University of California at Berkeley (UC-Berkeley), GE, and Bechtel National, Inc. (BNI), is described and selected results are presented. The initial testing indicated excellent performance of high-damping natural-rubber bearings. The development of seismic isolation guidelines is in progress as a joint activity between ENEA of Italy and the GE Team. (orig./HP)

  13. Development of BASIC program for radiocarbon dating

    International Nuclear Information System (INIS)

    Omoto, Kunio

    1982-01-01

    The continuous improvement of the system and the needs have produced the successful radiocarbon dating system of today to detect very low energy β-radioactivity. However, it still takes longer than 1,000 minutes for a sample counting. In a gas counting system, it is very difficult to keep the drift of impressed high voltage for a proportional counter less than 5 volts throughout the counting time. The temperature and the characteristics of gas itself also change during experiment. The accumulation of the above drift and errors are closely concerned with the accuracy and reliability of the radiocarbon date. The detection and reduction of the errors are only possible by using a ''fully automatic radiocarbon dating system'' linked to a personal computer system. In this paper, the author presents the BASIC (Beginners All-purpose Symbolic Instruction Code) program for a fully automatic radiocarbon dating system. In this paper, the outline of the system and software development are described. The details of the program include the description for gas-collection, gas-enclosing, plateau counting, β-ray counting, age calculation and data file maintenance. The author wrote numerous remark statements into the program so that it can be understood by users without detailed knowledge of the operation of a personal computer system or of the radiocarbon dating. Using this system, the author found that the radiocarbon dating has greatly progressed in speed and labour-saving, and that the accuracy and reliability of the date itself has also improved much than former manual systems. (Wakatsuki, Y.)

  14. GSG-GIS development program plan

    International Nuclear Information System (INIS)

    Lee, R.C.

    1992-01-01

    For the past 40 years, the Savannah River Site (SRS) has been subjected to numerous geological and geotechnical investigations in support of facility construction and waste site development and remediation. Over this period,.a variety of different subcontractors have collected large quantities of geoscience data. In addition, current programs involve numerous investigators from different departments, and consequently, earth science data and interpretations are scattered among the departments, investigators, and subcontractors at SRS. As a result, scientific and management decisions cannot take advantage of the significant body of information that exists at SRS. Recent DOE Orders (Systematic Evaluation Program, 1991) have put specific requirements on their contractors to compile geological databases to coordinate DOE site data gathering and interpretations, and to assist in compiling safety analysis reports. The Earth Science Advisory Committee and the Environmental Advisory Committee have also made specific recommendations on the management of SRS geoscience data. This plan describes a management system to identify, communicate, and compile SRS geological (including geohydrologic), seismological, and geotechnical (656) data and interpretations on a Geographic Information System (GIS)

  15. Large rotorcraft transmission technology development program

    Science.gov (United States)

    Mack, J. C.

    1983-01-01

    Testing of a U.S. Army XCH-62 HLH aft rotor transmission under NASA Contract NAS 3-22143 was successfully completed. This test establishes the feasibility of large, high power rotorcraft transmissions as well as demonstrating the resolution of deficiencies identified during the HLH advanced technology programs and reported by USAAMRDLTR-77-38. Over 100 hours of testing was conducted. At the 100% design power rating of 10,620 horsepower, the power transferred through a single spiral bevel gear mesh is more than twice that of current helicopter bevel gearing. In the original design of these gears, industry-wide design methods were employed and failures were experienced which identified problem areas unique to gear size. To remedy this technology shortfall, a program was developed to predict gear stresses using finite element analysis for complete and accurate representation of the gear tooth and supporting structure. To validate the finite element methodology gear strain data from the existing U.S. Army HLH aft transmission was acquired, and existing data from smaller gears were made available.

  16. Young Athletes program: impact on motor development.

    Science.gov (United States)

    Favazza, Paddy C; Siperstein, Gary N; Zeisel, Susan A; Odom, Samuel L; Sideris, John H; Moskowitz, Andrew L

    2013-07-01

    This study examined the effectiveness of the Young Athletes program to promote motor development in preschool-aged children with disabilities. In the study, 233 children were randomly assigned to a control group or the Young Athletes (YA) intervention group which consisted of 24 motor skill lessons delivered 3 times per week for 8 weeks. Hierarchical Linear Modeling (HLM) showed that children who participated in the YA intervention exhibited mean gains of 7-9 months on the Peabody Developmental Motor Subscales (PDMS) compared with mean gains of 3-5 months for the control group. Children in the YA intervention also exhibited significant gains on the gross motor subscale of the Vineland Teacher Rating Form (VTRF). Teachers and parents reported benefits for children not only in specific motor skills, but also kindergarten readiness skills and social/play skills. The necessity for direct and intentional instruction of motor skills, as well as the challenges of involving families in the YA program, are discussed.

  17. Development of a VMAT quality assurance program

    International Nuclear Information System (INIS)

    Silva, Ricardo Goulart da

    2013-01-01

    Modern radiation therapy keeps evolving and the technological changes include new imaging modalities, new patient immobilization devices and new treatment delivery systems. These advances have made it possible to reduce the dose to normal tissue structures and consequently minimize the risk of toxicity and morbidity, while allowing for dose escalation to the tumor volumes, potentially leading to improved locoregional control. Traditional IMRT techniques offer all of these features but the treatment session time is usually long, mainly for the head and neck cases. Currently, the VMAT technique is a reality in reference centers around the world. This technology has improved delivery efficiency over IMRT, decreasing the treatment application time, as this modality introduces extra degrees of freedom in the optimization process. The modulation of the radiation beams is achieved by simultaneous variation of dynamic parameters such as dose rate, gantry speed and leaves speed. The high level of complexity associated to the new treatment trends, inevitably, requires more accuracy and more rigorous quality assurance programs. The commissioning methods reported for the Varian RapidArc system were extended to an Elekta Synergy linear accelerator, using custom files built in the iComCAT software. Specific tests for the machine quality assurance are presented and also the dosimetric validation process applied to the Monaco treatment planning system. The MLC parameters, modeled by the Monte Carlo algorithm, were analyzed and the TG 119 tests were adapted for VMAT planning. In the end, a specific program developed for the VMAT technology for Elekta accelerators is presented. (author)

  18. Does Tumor Development Follow a Programmed Path?

    Science.gov (United States)

    Austin, Robert

    2011-03-01

    The initiation and progression of a tumor is a complex process, resembling the growth of a embryo in terms of the stages of development and increasing differentiation and somatic evolution of constituent cells in the community of cells that constitute the tumor. Typically we view cancer cells as rogue individuals violating the rules of the games played within an organism, but I would suggest that what we see is a programmed and algorithmic process. I will then question If tumor progression is dominated by the random acquisition of successive survival traits, or by a systematic and sequential unpacking of ``weapons'' from a pre-adapted ``toolkit'' of genetic and epigenetic potentialities? Can we then address this hypothesis by data mining solid tumors layer by layer? Support of the NSF and the NCI is gratefully acknowledged.

  19. DOE EM industry programs robotics development

    International Nuclear Information System (INIS)

    Staubly, R.; Kothari, V.

    1998-01-01

    The Office of Science and Technology (OST) manages an aggressive program for RD and D, as well as testing and evaluation for the Department of Energy's (DOE's) Environmental Management (EM) organization. The goal is to develop new and improved environmental restoration and waste management technologies to clean up the inventory of the DOE weapons complex faster, safer, and cheaper than is possible with currently available technologies. Robotic systems reduce worker exposure to the absolute minimum, while providing proven, cost-effective, and, for some applications, the only acceptable technique for addressing challenging problems. Development of robotic systems for remote operations occurs in three main categories: tank waste characterization and retrieval; decontamination and dismantlement; and characterization, mapping, and inspection systems. In addition, the Federal Energy Technology Center (FETC) has some other projects which fall under the heading of supporting R and D. The central objective of all FETC robotic projects is to make robotic systems more attractive by reducing costs and health risks associated with the deployment of robotic technologies in the cleanup of the nuclear weapons complex. This will be accomplished through development of robots that are cheaper, faster, safer, and more reliable, as well as more straightforward to modify/adapt and more intuitive to operate with autonomous capabilities and intelligent controls that prevent accidents and optimize task execution

  20. Advancing NOAA NWS Arctic Program Development

    Science.gov (United States)

    Timofeyeva-Livezey, M. M.; Horsfall, F. M. C.; Meyers, J. C.; Churma, M.; Thoman, R.

    2016-12-01

    Environmental changes in the Arctic require changes in the way the National Oceanic and Atmospheric Administration (NOAA) delivers hydrological and meteorological information to prepare the region's societies and indigenous population for emerging challenges. These challenges include changing weather patterns, changes in the timing and extent of sea ice, accelerated soil erosion due to permafrost decline, increasing coastal vulnerably, and changes in the traditional food supply. The decline in Arctic sea ice is opening new opportunities for exploitation of natural resources, commerce, tourism, and military interest. These societal challenges and economic opportunities call for a NOAA integrated approach for delivery of environmental information including climate, water, and weather data, forecasts, and warnings. Presently the NOAA Arctic Task Force provides leadership in programmatic coordination across NOAA line offices. National Weather Service (NWS) Alaska Region and the National Centers for Environmental Prediction (NCEP) provide the foundational operational hydro-meteorological products and services in the Arctic. Starting in 2016, NOAA's NWS will work toward improving its role in programmatic coordination and development through assembling an NWS Arctic Task Team. The team will foster ties in the Arctic between the 11 NWS national service programs in climate, water, and weather information, as well as between Arctic programs in NWS and other NOAA line offices and external partners. One of the team outcomes is improving decision support tools for the Arctic. The Local Climate Analysis Tool (LCAT) currently has more than 1100 registered users, including NOAA staff and technical partners. The tool has been available online since 2013 (http://nws.weather.gov/lcat/ ). The tool links trusted, recommended NOAA data and analytical capabilities to assess impacts of climate variability and climate change at local levels. A new capability currently being developed will

  1. Program for developing leadership in pharmacy residents.

    Science.gov (United States)

    Fuller, Patrick D

    2012-07-15

    An innovative, structured approach to incorporating leadership development activities into pharmacy residency training is described. The American Society of Health-System Pharmacists (ASHP) has called for increased efforts to make leadership development an integral component of the training of pharmacy students and new practitioners. In 2007, The Nebraska Medical Center (TNMC) took action to systematize leadership training in its pharmacy residency programs by launching a new Leadership Development Series. Throughout the residency year, trainees at TNMC participate in a variety of activities: (1) focused group discussions of selected articles on leadership concepts written by noted leaders of the past and present, (2) a two-day offsite retreat featuring trust-building exercises and physical challenges, (3) a self-assessment designed to help residents identify and use their untapped personal strengths, (4) training on the effective application of different styles of communication and conflict resolution, and (5) education on the history and evolution of health-system pharmacy, including a review and discussion of lectures by recipients of ASHP's Harvey A. K. Whitney Award. Feedback from residents who have completed the series has been positive, with many residents indicating that it has stimulated their professional growth and helped prepared them for leadership roles. A structured Leadership Development Series exposes pharmacy residents to various leadership philosophies and principles and, through the study of Harvey A. K. Whitney Award lectures, to the thoughts of past and present pharmacy leaders. Residents develop an increased self-awareness through a resident fall retreat, a StrengthsFinder assessment, and communication and conflict-mode assessment tools.

  2. Development of bearing capacity of fine grained permafrost deposits in western greenland urban areas subject to soil temperature changes

    DEFF Research Database (Denmark)

    Agergaard, Frederik Ancker; Ingeman-Nielsen, Thomas

    2012-01-01

    The bearing capacity of frozen soils is high, compared to non-frozen soils of same composition. Projected climatic warming in the Arctic will increase the soil temperature, thus affecting the bearing capacity and the deformation properties. Western Greenland temperatures are projected to increase...... free samples. Unfrozen water contents are seen to be directly inversely proportional to the undrained shear strength when both are normalized, which may reduce costs for establishing reliable soil strength parameters. It is suggested that a relation to deformation parameters are investigated as well...

  3. Weight-bearing locomotion in the developing opossum, Monodelphis domestica following spinal transection: remodeling of neuronal circuits caudal to lesion.

    Science.gov (United States)

    Wheaton, Benjamin J; Noor, Natassya M; Whish, Sophie C; Truettner, Jessie S; Dietrich, W Dalton; Zhang, Moses; Crack, Peter J; Dziegielewska, Katarzyna M; Saunders, Norman R

    2013-01-01

    Complete spinal transection in the mature nervous system is typically followed by minimal axonal repair, extensive motor paralysis and loss of sensory functions caudal to the injury. In contrast, the immature nervous system has greater capacity for repair, a phenomenon sometimes called the infant lesion effect. This study investigates spinal injuries early in development using the marsupial opossum Monodelphis domestica whose young are born very immature, allowing access to developmental stages only accessible in utero in eutherian mammals. Spinal cords of Monodelphis pups were completely transected in the lower thoracic region, T10, on postnatal-day (P)7 or P28 and the animals grew to adulthood. In P7-injured animals regrown supraspinal and propriospinal axons through the injury site were demonstrated using retrograde axonal labelling. These animals recovered near-normal coordinated overground locomotion, but with altered gait characteristics including foot placement phase lags. In P28-injured animals no axonal regrowth through the injury site could be demonstrated yet they were able to perform weight-supporting hindlimb stepping overground and on the treadmill. When placed in an environment of reduced sensory feedback (swimming) P7-injured animals swam using their hindlimbs, suggesting that the axons that grew across the lesion made functional connections; P28-injured animals swam using their forelimbs only, suggesting that their overground hindlimb movements were reflex-dependent and thus likely to be generated locally in the lumbar spinal cord. Modifications to propriospinal circuitry in P7- and P28-injured opossums were demonstrated by changes in the number of fluorescently labelled neurons detected in the lumbar cord following tracer studies and changes in the balance of excitatory, inhibitory and neuromodulatory neurotransmitter receptors' gene expression shown by qRT-PCR. These results are discussed in the context of studies indicating that although

  4. Weight-bearing locomotion in the developing opossum, Monodelphis domestica following spinal transection: remodeling of neuronal circuits caudal to lesion.

    Directory of Open Access Journals (Sweden)

    Benjamin J Wheaton

    Full Text Available Complete spinal transection in the mature nervous system is typically followed by minimal axonal repair, extensive motor paralysis and loss of sensory functions caudal to the injury. In contrast, the immature nervous system has greater capacity for repair, a phenomenon sometimes called the infant lesion effect. This study investigates spinal injuries early in development using the marsupial opossum Monodelphis domestica whose young are born very immature, allowing access to developmental stages only accessible in utero in eutherian mammals. Spinal cords of Monodelphis pups were completely transected in the lower thoracic region, T10, on postnatal-day (P7 or P28 and the animals grew to adulthood. In P7-injured animals regrown supraspinal and propriospinal axons through the injury site were demonstrated using retrograde axonal labelling. These animals recovered near-normal coordinated overground locomotion, but with altered gait characteristics including foot placement phase lags. In P28-injured animals no axonal regrowth through the injury site could be demonstrated yet they were able to perform weight-supporting hindlimb stepping overground and on the treadmill. When placed in an environment of reduced sensory feedback (swimming P7-injured animals swam using their hindlimbs, suggesting that the axons that grew across the lesion made functional connections; P28-injured animals swam using their forelimbs only, suggesting that their overground hindlimb movements were reflex-dependent and thus likely to be generated locally in the lumbar spinal cord. Modifications to propriospinal circuitry in P7- and P28-injured opossums were demonstrated by changes in the number of fluorescently labelled neurons detected in the lumbar cord following tracer studies and changes in the balance of excitatory, inhibitory and neuromodulatory neurotransmitter receptors' gene expression shown by qRT-PCR. These results are discussed in the context of studies indicating

  5. Program Management Officer | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    English · Français ... Reviews project and program material and prepares synthesis documents of results, decisions, and directions for team discussion; Researches specific topics of interest to the program to enrich the knowledge of team ...

  6. Program Assistant | IDRC - International Development Research ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Job Summary Under the direction of the Program Leader, the Program ... of the operations of the Program, and assists with information management the team. ... and distribution of documents and providing the necessary technical devices;; Takes ... mailings or distribution;; Prepares training kits or information packages and ...

  7. Developing a Mentorship Program in Laos

    Directory of Open Access Journals (Sweden)

    Helen Nita Catton

    2017-06-01

    Full Text Available Skills strengthening and capacity building for maternal and newborn health (MNH providers are essential to ensure quality care for mothers and newborns. There is, however, limited research regarding what constitutes an effective model in low-income countries. The Lao People’s Democratic Republic (Laos has some of the region’s worst outcomes for neonatal and maternal mortality. Moreover, with a 23-year hiatus in midwifery training, which ended approximately 7 years ago, there is a cadre of new and inexperienced midwives in practice without support systems, skills, or continuing professional development opportunities. Traditional didactic teaching methodologies prevail in Laos, but with little evidence of efficacy. As an alternative model, Save the Children International has been implementing a mentorship approach for MNH providers in two provinces in northern Laos since January 2016, with technical guidance and funding from the United States Agency for International Development-supported global Maternal Child Survival Program. This community case study will describe and reflect on the approach by highlighting the need and rationale for mentorship, followed by a description of the program’s core components and the results observed so far. Lessons learned and the application of the approach to different contexts and health-care professionals, considering both constraints and opportunities, will be discussed.

  8. Hot Dry Rock Geothermal Energy Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Smith, M.C.; Hendron, R.H.; Murphy, H.D.; Wilson, M.G.

    1989-12-01

    During Fiscal Year 1987, emphasis in the Hot Dry Rock Geothermal Energy Development Program was on preparations for a Long-Term Flow Test'' of the Phase II'' or Engineering'' hot dry rock energy system at Fenton Hill, New Mexico. A successful 30-day flow test of the system during FY86 indicated that such a system would produce heat at a temperature and rate that could support operation of a commercial electrical power plant. However, it did not answer certain questions basic to the economics of long-term operation, including the rate of depletion of the thermal reservoir, the rate of water loss from the system, and the possibility of operating problems during extended continuous operation. Preparations for a one-year flow test of the system to answer these and more fundamental questions concerning hot dry rock systems were made in FY87: design of the required surface facilities; procurement and installation of some of their components; development and testing of slimline logging tools for use through small-diameter production tubing; research on temperature-sensitive reactive chemical tracers to monitor thermal depletion of the reservoir; and computer simulations of the 30-day test, extended to modeling the planned Long-Term Flow Test. 45 refs., 34 figs., 5 tabs.

  9. Programmed cell death during quinoa perisperm development.

    Science.gov (United States)

    López-Fernández, María Paula; Maldonado, Sara

    2013-08-01

    At seed maturity, quinoa (Chenopodium quinoa Willd.) perisperm consists of uniform, non-living, thin-walled cells full of starch grains. The objective of the present study was to study quinoa perisperm development and describe the programme of cell death that affects the entire tissue. A number of parameters typically measured during programmed cell death (PCD), such as cellular morphological changes in nuclei and cytoplasm, endoreduplication, DNA fragmentation, and the participation of nucleases and caspase-like proteases in nucleus dismantling, were evaluated; morphological changes in cytoplasm included subcellular aspects related to starch accumulation. This study proved that, following fertilization, the perisperm of quinoa simultaneously accumulates storage reserves and degenerates, both processes mediated by a programme of developmentally controlled cell death. The novel findings regarding perisperm development provide a starting point for further research in the Amaranthaceae genera, such as comparing seeds with and without perisperm, and specifying phylogeny and evolution within this taxon. Wherever possible and appropriate, differences between quinoa perisperm and grass starchy endosperm--a morphologically and functionally similar, although genetically different tissue--were highlighted and discussed.

  10. Designing and Managing Successful International Joint Development Programs

    Science.gov (United States)

    2016-04-30

    joint development programs are important because of their potential to reduce costs and increase partnership benefits such as interoperability, economies ...have actualized by discussing what characteristics research has shown as crucial to international joint development program outcomes. The study team... characteristics of international joint development programs that result in positive or negative cost, scheduling, and end-product outcomes, such as a final

  11. Waste sludge resuspension and transfer: development program

    International Nuclear Information System (INIS)

    Weeren, H.O.; Mackey, T.S.

    1980-02-01

    The six Gunite waste tanks at Oak Ridge National Laboratory (ORNL) contain about 400,000 gal of sludge that has precipitated from solution and settled during the 35 years these tanks have been in service. Eventual decommissioning of the tanks has been proposed. The first part of this program is to resuspend the accumulated sludge, to transfer it to new storage tanks in Melton Valley, and to dispose of it by the shale-fracturing process. On the basis of preliminary information, a tentative operational concept was adopted. The sludge in each tank would be resuspended by hydraulic sluicing and pumped from the tank. This resuspended sludge would be treated as necessary to keep the particles in suspension and would be pumped to the new waste-storage tanks. Subsequently the sludge would be pumped from the tanks, combined with a cement-base mix, and disposed of by the shale-fracturing facility. Verification of the feasibility of this concept required development effort on characterization of the sludge and development of techniques for resuspending the sludge and for keeping it in suspension. These development efforts are described in this report. Sections of the report describe both the known properties of the sludge and the tests of grinding methods investigated, discuss tests of various suspenders, describe tests with cement-base mixes, summarize hot-cell tests on actual sludge samples, and describe tests that were made at a mockup of a Gunite tank installation. On the basis of the tests made, it was concluded that reslurrying and resuspension of the sludge is quite feasible and that the suspensions can be made compatible with cement mixes

  12. Lateral load performance of SIP walls with full bearing

    Science.gov (United States)

    Boren Yeh; Tom Skaggs; Xiping Wang; Tom Williamson

    2018-01-01

    The purpose of this study was to develop test data needed to characterize lateral load performance of structural insulated panel (SIP) walls with full bearing (restrained). The research program involved structural testing of 29 full-size SIP walls (8 ft tall by 8 ft long) of various configurations that bracket a range of SIP wall configurations commonly used in the...

  13. Development and test of model apparatus of non-contact spin processor for photo mask production applying radial-type superconducting magnetic bearing

    International Nuclear Information System (INIS)

    Saito, Kimiyo; Fukui, Satoshi; Maezawa, Masaru; Ogawa, Jun; Oka, Tetsuo; Sato, Takao

    2013-01-01

    Highlights: ► We develop test spinner for non-contact spinning process in photo mask production. ► This test spinner shows improved spinning ability compared with our previous one. ► Large vertical movement of turn table still occurs during acceleration. ► Method to control vertical movement of turn table should be developed in next step. -- Abstract: In semiconductor devices, miniaturization of circuit patterning on wafers is required for higher integrations of circuit elements. Therefore, very high tolerance and quality are also required for patterning of microstructures of photo masks. The deposition of particulate dusts generated from mechanical bearings of the spin processor in the patterns of the photo mask is one of main causes of the deterioration of pattern preciseness. In our R and D, application of magnetic bearing utilizing bulk high temperature superconductors to the spin processors has been proposed. In this study, we develop a test spinner for the non-contact spinning process in the photo mask production system. The rotation test by using this test spinner shows that this test spinner accomplishes the improvement of the spinning ability compared with the test spinner developed in our previous study. This paper describes the rotation test results of the new test spinner applying the magnetic bearing with bulk high temperature superconductors

  14. Regularities in the +H14C assimilate supply of peach fruits at their last development stage within the range of a fruit-bearing branchlet

    International Nuclear Information System (INIS)

    Petrov, A.; Manolov, P.

    1977-01-01

    Studies have been accomplished by means of 14 C and autoradiography on the transport link between individual shoots and Redhaven fruits in their advanced development (about a week before maturity) which have formed within the range of a fruit-bearing branchlet. This confirms the conception of directing the photosynthetic prod%cts mainly to the ripening fruits. The basic regularities of the photoassimilate transport prove to be the same as at an early phase of fruit development. Nevertheless, there are also some new traits of morphological and physiological essence such as relatively a large phloem fibre scope of the fruit-bearing branchlet, creating better possibilities of taking over the transport products of the photosynthesis and enhanced attraction opwer of fruits, conditioning a strengthened linear and additional transversal transport, thus contributing to the rapid growth of fruits in their last development phase. Under the influence of these factors, the independence of individual shoots and fruits along and around a fruit-bearing branchlet is substantially less than at an early development phase. (author)

  15. Applying QA to nuclear-development programs

    International Nuclear Information System (INIS)

    Caplinger, W.H.

    1981-12-01

    The application of quality assurance (QA) principles to developmental programs is usually accomplished by tailoring or selecting appropriate requirements from large QA systems. Developmental work at Westinghouse Hanford Company (WHC) covers the complete range from basic research to in-core reactor tests. Desired requirements are selected from the 18 criteria in ANSI/ASME NQA Standard 1 by the cognizant program engineer in conjunction with the quality engineer. These referenced criteria assure that QA for the program is planned, implemented, and maintained. In addition, the WHC QA Manual provides four categories or levels of QA that are assigned to programs or components within the program. These categories are based on safety, reliability, and consequences of failure to provide a cost effective program

  16. Effect of prenatal programming on heifer development.

    Science.gov (United States)

    Funston, Richard N; Summers, Adam F

    2013-11-01

    In beef cattle, the main factors influencing nutrient partitioning between the dam and fetus include age of the dam, number of fetuses, production demand, and environmental stress. These factors play a critical role in programming the fetus for its future environment and available resources. Fetal programming reportedly affects neonatal mortality and morbidity, postnatal growth rate, body composition, health, and reproduction. Two main mechanisms responsible for fetal programming include DNA methylation and histone modifications. Alterations in the genome can be passed through multiple generations. Maternal environment (nutrition, age, physiologic status) can program progeny heifer growth and reproductive performance. Copyright © 2013 Elsevier Inc. All rights reserved.

  17. Reviewing a Reading Program: Professional Development Module. Facilitator's Guide

    Science.gov (United States)

    Kosanovich, Marcia; Jordan, Georgia; Arndt, Elissa; VanSciver, Mary; Wahl, Michelle; Rissman, Lila

    2008-01-01

    This "Facilitator's Guide" has been prepared for presenters of the Reviewing a Reading Program professional development training. It is one of three pieces comprising a suite of materials on reviewing reading programs: this "Guide", the "Reviewing a Reading Program Participant's Guide" and the "Reviewing a Reading Program" Professional Development…

  18. Hydrogen hybrid vehicle engine development: Experimental program

    Energy Technology Data Exchange (ETDEWEB)

    Van Blarigan, P. [Sandia National Lab., Livermore, CA (United States)

    1995-09-01

    A hydrogen fueled engine is being developed specifically for the auxiliary power unit (APU) in a series type hybrid vehicle. Hydrogen is different from other internal combustion (IC) engine fuels, and hybrid vehicle IC engine requirements are different from those of other IC vehicle engines. Together these differences will allow a new engine design based on first principles that will maximize thermal efficiency while minimizing principal emissions. The experimental program is proceeding in four steps: (1) Demonstration of the emissions and the indicated thermal efficiency capability of a standard CLR research engine modified for higher compression ratios and hydrogen fueled operation. (2) Design and test a new combustion chamber geometry for an existing single cylinder research engine, in an attempt to improve on the baseline indicated thermal efficiency of the CLR engine. (3) Design and build, in conjunction with an industrial collaborator, a new full scale research engine designed to maximize brake thermal efficiency. Include a full complement of combustion diagnostics. (4) Incorporate all of the knowledge thus obtained in the design and fabrication, by an industrial collaborator, of the hydrogen fueled engine for the hybrid vehicle power train illustrator. Results of the CLR baseline engine testing are presented, as well as preliminary data from the new combustion chamber engine. The CLR data confirm the low NOx produced by lean operation. The preliminary indicated thermal efficiency data from the new combustion chamber design engine show an improvement relative to the CLR engine. Comparison with previous high compression engine results shows reasonable agreement.

  19. Dissimilar weld failure analysis and development program

    International Nuclear Information System (INIS)

    Holko, K.H.; Li, C.C.

    1982-01-01

    The problem of dissimilar weld cracking and failure is examined. This problem occurs in boiler superheater and reheater sections as well as main steam piping. Typically, a dissimilar weld joins low-alloy steel tubing such as Fe-2-1/4 Cr-1Mo to stainless steel tubing such as 321H and 304H. Cracking and failure occur in the low-alloy steel heat-affected zone very close to the weld interface. The 309 stainless steel filler previously used has been replaced with nickel-base fillers such as Inconel 132, Inconel 182, and Incoweld A. This change has extended the time to cracking and failure, but has not solved the problem. To illustrate and define the problem, the metallography of damaged and failed dissimilar welds is described. Results of mechanical tests of dissimilar welds removed from service are presented, and factors believed to be influential in causing damage and failure are discussed. In addition, the importance of dissimilar weldment service history is demonstrated, and the Dissimilar Weld Failure Analysis and Development Program is described. 15 figures

  20. Space Station alpha joint bearing

    Science.gov (United States)

    Everman, Michael R.; Jones, P. Alan; Spencer, Porter A.

    1987-01-01

    Perhaps the most critical structural system aboard the Space Station is the Solar Alpha Rotary Joint which helps align the power generation system with the sun. The joint must provide structural support and controlled rotation to the outboard transverse booms as well as power and data transfer across the joint. The Solar Alpha Rotary Joint is composed of two transition sections and an integral, large diameter bearing. Alpha joint bearing design presents a particularly interesting problem because of its large size and need for high reliability, stiffness, and on orbit maintability. The discrete roller bearing developed is a novel refinement to cam follower technology. It offers thermal compensation and ease of on-orbit maintenance that are not found in conventional rolling element bearings. How the bearing design evolved is summarized. Driving requirements are reviewed, alternative concepts assessed, and the selected design is described.

  1. Development of nuclear safety issues program

    Energy Technology Data Exchange (ETDEWEB)

    Cho, J. C.; Yoo, S. O.; Yoon, Y. K.; Kim, H. J.; Jeong, M. J.; Noh, K. W.; Kang, D. K

    2006-12-15

    The nuclear safety issues are defined as the cases which affect the design and operation safety of nuclear power plants and also require the resolution action. The nuclear safety issues program (NSIP) which deals with the overall procedural requirements for the nuclear safety issues management process is developed, in accordance with the request of the scientific resolution researches and the establishment/application of the nuclear safety issues management system for the nuclear power plants under design, construction or operation. The NSIP consists of the following 4 steps; - Step 1 : Collection of candidates for nuclear safety issues - Step 2 : Identification of nuclear safety issues - Step 3 : Categorization and resolution of nuclear safety issues - Step 4 : Implementation, verification and closure The NSIP will be applied to the management directives of KINS related to the nuclear safety issues. Through the identification of the nuclear safety issues which may be related to the potential for accident/incidents at operating nuclear power plants either directly or indirectly, followed by performance of regulatory researches to resolve the safety issues, it will be possible to prevent occurrence of accidents/incidents as well as to cope with unexpected accidents/incidents by analyzing the root causes timely and scientifically and by establishing the proper flow-up or remedied regulatory actions. Moreover, the identification and resolution of the safety issues related to the new nuclear power plants completed at the design stage are also expected to make the new reactor licensing reviews effective and efficient as well as to make the possibility of accidents/incidents occurrence minimize. Therefore, the NSIP developed in this study is expected to contribute for the enhancement of the safety of nuclear power plants.

  2. Development of nuclear safety issues program

    International Nuclear Information System (INIS)

    Cho, J. C.; Yoo, S. O.; Yoon, Y. K.; Kim, H. J.; Jeong, M. J.; Noh, K. W.; Kang, D. K.

    2006-12-01

    The nuclear safety issues are defined as the cases which affect the design and operation safety of nuclear power plants and also require the resolution action. The nuclear safety issues program (NSIP) which deals with the overall procedural requirements for the nuclear safety issues management process is developed, in accordance with the request of the scientific resolution researches and the establishment/application of the nuclear safety issues management system for the nuclear power plants under design, construction or operation. The NSIP consists of the following 4 steps; - Step 1 : Collection of candidates for nuclear safety issues - Step 2 : Identification of nuclear safety issues - Step 3 : Categorization and resolution of nuclear safety issues - Step 4 : Implementation, verification and closure The NSIP will be applied to the management directives of KINS related to the nuclear safety issues. Through the identification of the nuclear safety issues which may be related to the potential for accident/incidents at operating nuclear power plants either directly or indirectly, followed by performance of regulatory researches to resolve the safety issues, it will be possible to prevent occurrence of accidents/incidents as well as to cope with unexpected accidents/incidents by analyzing the root causes timely and scientifically and by establishing the proper flow-up or remedied regulatory actions. Moreover, the identification and resolution of the safety issues related to the new nuclear power plants completed at the design stage are also expected to make the new reactor licensing reviews effective and efficient as well as to make the possibility of accidents/incidents occurrence minimize. Therefore, the NSIP developed in this study is expected to contribute for the enhancement of the safety of nuclear power plants

  3. Development of ceramics for heavy-duty roller bearings in key sectors of future technologies. Ceramic bearings for turbomolecular pumps in semiconductor industry. Final report; Entwicklung von Hochleistungskeramiken fuer Keramikwaelzlager unter extremen Belastungen in Schluesselbereichen von Zukunftstechnologien. Keramikwaelzlager fuer Turbomolekularpumpen in der Halbleiterindustrie. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Stueber, H.G.; Adamietz, R.; Binninger, M. [and others

    1999-09-01

    The examined ceramic material shows high resistance against aggressive gases used in the semiconductor industry. In the test rigs for emergency bearings the full ceramic bearings without any lubricant didn't reach the requested life. Bearings with ZrO{sub 2}-rings reached higher life time compared to bearings with Si{sub 3}N{sub 4}-rings. The life of the emergency bearings increased when using C-ion implanted rings. By using this method the friction ratio decreased. In this case, bearings with ZrO{sub 2}-rings get nearly the life of the old standard hybrid emergency bearings. But they can't reach the life time of the latest state of development of hybrid bearings. A two row paired angular contact bearing seems to be a most promising modification. But this design shows problems while manufacturing. The so called pin-bush-bearing (a sliding friction bearing solution) shows good test results. It will be possible to optimise this bearing for different pumps. Tests with ceramic bearings in a conventional levitated pump were planned. It was not possible to start the tests because of the higher priority of the 'emergency bearing project'. (orig.) [German] Der untersuchte keramische Werkstoff weist eine hohe Bestaendigkeit gegenueber den in der Halbleiterindustrie verwendeten aggressiven Gasen auf. In den Fanglagerversuchen wurde deutlich, dass die untersuchten Vollkeramik-Waelzlager ohne Schmierstoff nicht die geforderten Standzeiten erreichen. Im Vergleich zwischen Si{sub 3}N{sub 4}-Ringen zur ZrO{sub 2}-Ringen lassen die Oxidringe eine hoehere Lebensdauer erwarten. Eine Verbesserung der Standzeiten konnte durch mit C-Ionen implantierten Ringe erzielt werden. Mit dieser Reibwertverbesserung konnten die Lager mit ZrO{sub 2}-Ringen zwar den alten Serienstandard mit Hybridlagern in etwa erreichen, andererseits sind zum jetzigen Serienstandard noch deutliche Unterschiede zu beobachten. Eine vielversprechende Modifikation des Lagers in Richtung eines

  4. Developing Financial Resources for School Arts Programs.

    Science.gov (United States)

    Green, Alan C.; Ambler, Nancy Morison

    This document provides a sampling of financial resources for fine arts programs in the schools and lists methods for submitting proposals and dealing with sponsors of funds. Financial sources for arts programs include school districts, organizations and institutions, special events, direct mail, individuals, associations and clubs, businesses and…

  5. GSI research and development program 1989

    International Nuclear Information System (INIS)

    1989-01-01

    In the year 1989 the SIS will come into operation and the erection of the ESR will be finished. The construction of a new uranium injector for an independent low-energy program at UNILAC has begun. Furthermore the UNILAC is available for the SIS injection and an experimental low-energy program confined by this. (orig./HSI) [de

  6. The MSCA Program: Developing Analytic Unicorns

    Science.gov (United States)

    Houghton, David M.; Schertzer, Clint; Beck, Scott

    2018-01-01

    Marketing analytics students who can communicate effectively with decision makers are in high demand. These "analytic unicorns" are hard to find. The Master of Science in Customer Analytics (MSCA) degree program at Xavier University seeks to fill that need. In this paper, we discuss the process of creating the MSCA program. We outline…

  7. Design and Development of a Nonverbal Program

    Science.gov (United States)

    Thiagarajan, S.

    1973-01-01

    Problems were encountered in designing an illustrated program on contraceptive techniques for India's rural population where illiteracy is high and hundreds of different languages are spoken. Field trials of a picture program indicated the ability to "read" a picture is an acquired skill. (Author)

  8. 36 CFR 13.1236 - Bear orientation.

    Science.gov (United States)

    2010-07-01

    ... 36 Parks, Forests, and Public Property 1 2010-07-01 2010-07-01 false Bear orientation. 13.1236 Section 13.1236 Parks, Forests, and Public Property NATIONAL PARK SERVICE, DEPARTMENT OF THE INTERIOR... Developed Area § 13.1236 Bear orientation. All persons visiting the BCDA must receive an NPS-approved Bear...

  9. Load-bearing masonry system adoption and performance: A case study of construction company in a developing country

    Science.gov (United States)

    Ramli, Nor Azlinda; Abdullah, Che Sobry; Nawi, Mohd Nasrun Mohd; Bahaudin, Ahmad Yusni

    2016-08-01

    This study addresses the factors that influence the adoption of load-bearing masonry (LBM) system. A case study of the load-bearing masonry (LBM) system adoption is conducted through an interview to explore the situation of the technology adoption in a construction company. The finding indicates the factors influence the adoption of LBM system for the construction company are: organizational resources, usefulness, less maintenance, reduce construction time and cost. From the findings, these factors consistent with previous literature. Furthermore, the performance of the company was measured by looking into the financial and non-financial aspects. The LBM system brings good performance as it increased the profits of the company, a good quality of product and attracts more demand from customers. Thus, these factors should be considered for the other companies that are interested in implementing the LBM system in their projects.

  10. Summary of experimental tests of elastomeric seismic isolation bearings for use in nuclear reactor plants

    International Nuclear Information System (INIS)

    Seidensticker, R.W.; Chang, Y.W.; Kulak, R.F.

    1992-01-01

    This paper describes an experimental test program for isolator bearings which was developed to help establish the viability of using laminated elastomer bearings for base isolation of nuclear reactor plants. The goal of the test program is to determine the performance characteristics of laminated seismic isolation bearings under a wide range of loadings. Tests were performed on scale-size laminated seismic isolators both within the design shear strain range to determine the response of the bearing under expected earthquake loading conditions, and beyond the design range to determine failure modes and to establish safety margins. Three types of bearings, each produced from a different manufacturer, have been tested: (1) high shape factor-high damping-high shear modulus bearings; (2) medium shape factor-high damping-high shear modulus bearings; and (3) medium shape factor-high damping-low shear modulus bearings. All of these tests described in this report were performed at the Earthquake Engineering Research Center at the University of California, Berkeley, with technical assistance from ANL. The tests performed on the three types of bearings have confirmed the high performance characteristics of the high damping-high and low shear modulus elastomeric bearings. The bearings have shown that they are capable of having extremely large shear strains before failure occurs. The most common failure mechanism was the debonding of the top steel plate from the isolators. This failure mechanism can be virtually eliminated by improved manufacturing quality control. The most important result of the failure test of the isolators is the fact that bearings can sustain large horizontal displacement, several times larger than the design value, with failure. Their performance in moderate and strong earthquakes will be far superior to conventional structures

  11. Development of parallel/serial program analyzing tool

    International Nuclear Information System (INIS)

    Watanabe, Hiroshi; Nagao, Saichi; Takigawa, Yoshio; Kumakura, Toshimasa

    1999-03-01

    Japan Atomic Energy Research Institute has been developing 'KMtool', a parallel/serial program analyzing tool, in order to promote the parallelization of the science and engineering computation program. KMtool analyzes the performance of program written by FORTRAN77 and MPI, and it reduces the effort for parallelization. This paper describes development purpose, design, utilization and evaluation of KMtool. (author)

  12. Fusion Energy Postdoctoral Research Program, Professional Development Program: FY 1987 annual report

    International Nuclear Information System (INIS)

    1988-01-01

    In FY 1986, Oak Ridge Associated Universities (ORAU) initiated two programs for the US Department of Energy (DOE), Office of Fusion Energy (OFE): the Fusion Energy Postdoctoral Research Program and the Fusion Energy Professional Development Program. These programs provide opportunities to conduct collaborative research in magnetic fusion energy research and development programs at DOE laboratories and contractor sites. Participants become trained in advanced fusion energy research, interact with outstanding professionals, and become familiar with energy-related national issues while making personal contributions to the search for solutions to scientific problems. Both programs enhance the national fusion energy research and development effort by providing channels for the exchange of scientists and engineers, the diffusion of ideas and knowledge, and the transfer of relevant technologies. These programs, along with the Magnetic Fusion Energy Science and Technology Fellowship Programs, compose the fusion energy manpower development programs administered by ORAU for DOE/OFE

  13. The United States Advanced Reactor Technologies Research and Development Program

    International Nuclear Information System (INIS)

    O’Connor, Thomas J.

    2014-01-01

    The following aspects are addressed: • Nuclear energy mission; • Reactor research development and deployment (RD&D) programs: - Light Water Reactor Sustainability Program; - Small Modular Reactor Licensing Technical Support; - Advanced Reactor Technologies (ART)

  14. Programming for the Public Good: Ensuring Public Value Through the Cooperative Extension Program Development Model

    Directory of Open Access Journals (Sweden)

    Nancy Franz

    2015-06-01

    Full Text Available Effective Cooperative Extension programs produce important private and public value for individuals, families, businesses, and communities. However, the public value of Extension programming often goes unmeasured and unarticulated. Extension needs to reclaim its role as a key provider of public value for Land-Grant Universities through strong educational programs driven by infusing public value into all elements of the Extension Program Development Model. This article describes Extension’s public value movement including organizational, professional, program, and scholarship development efforts to enhance public good effectiveness articulation. Lessons learned, implications, and next steps for Extension’s public value success through a strong program development model are also shared.

  15. Journal and Wave Bearing Impedance Calculation Software

    Science.gov (United States)

    Hanford, Amanda; Campbell, Robert

    2012-01-01

    The wave bearing software suite is a MALTA application that computes bearing properties for user-specified wave bearing conditions, as well as plain journal bearings. Wave bearings are fluid film journal bearings with multi-lobed wave patterns around the circumference of the bearing surface. In this software suite, the dynamic coefficients are outputted in a way for easy implementation in a finite element model used in rotor dynamics analysis. The software has a graphical user interface (GUI) for inputting bearing geometry parameters, and uses MATLAB s structure interface for ease of interpreting data. This innovation was developed to provide the stiffness and damping components of wave bearing impedances. The computational method for computing bearing coefficients was originally designed for plain journal bearings and tilting pad bearings. Modifications to include a wave bearing profile consisted of changing the film thickness profile given by an equation, and writing an algorithm to locate the integration limits for each fluid region. Careful consideration was needed to implement the correct integration limits while computing the dynamic coefficients, depending on the form of the input/output variables specified in the algorithm.

  16. New developments in program STANSOL version 3

    International Nuclear Information System (INIS)

    Gray, W.H.

    1981-10-01

    STANSOL is a computer program that applied a solution for the mechanical displacement, stress, and strain in rotationally-transversely isotropic, homogeneous, axisymmetric solenoids. Careful application of the solution permits the complex mechanical behavior of multilayered, nonhomogeneous solenoids to be examined in which the loads may vary arbitrarily from layer to layer. Loads applied to the solenoid model by program STANSOL may consist of differential temperature, winding preload, internal and/or external surface pressure, and electromagnetic Lorentz body forces. STANSOL version 3, the latest update to the original version of the computer program, also permits structural analysis of solenoid magnets in which frictionless interlayer gaps may open or close. This paper presents the new theory coded into version 3 of the STANSOL program, as well as the new input data format and graphical output display of the resulting analysis

  17. Establishing a Communications Officer Force Development Program

    National Research Council Canada - National Science Library

    Jenrette, Brian J

    2006-01-01

    ...: experience, skills, training, education, and performance feedback. However, the Air Force has not instituted the structure, supplied the resources, or mandated the governance to make the program a success...

  18. Program Development Plan and Team up; FINAL

    International Nuclear Information System (INIS)

    Solar Electric Power Association

    2001-01-01

    The final summary report is a comprehensive view of TEAM-UP, with documented data, information, and experiences that SEPA has collected throughout the program, including lessons learned by participating ventures, and sections covering costs and other information on both large and small systems. This report also covers the barriers that TEAM-UP faced to PV commercialization at the beginning of the program, barriers the project was able to remove or reduce, and what barriers remain on the road ahead

  19. Program Development Plan and Team up

    Energy Technology Data Exchange (ETDEWEB)

    Solar Electric Power Association

    2001-12-01

    The final summary report is a comprehensive view of TEAM-UP, with documented data, information, and experiences that SEPA has collected throughout the program, including lessons learned by participating ventures, and sections covering costs and other information on both large and small systems. This report also covers the barriers that TEAM-UP faced to PV commercialization at the beginning of the program, barriers the project was able to remove or reduce, and what barriers remain on the road ahead.

  20. Canadian fuel development program and recent operational experience

    International Nuclear Information System (INIS)

    Cox, D.S.; Kohn, E.; Lau, J.H.K.; Dicke, G.J.; Macici, N.N.; Sancton, R.W.

    1995-01-01

    This paper provides an overview of the current Canadian CANDU fuel R and D programs and operational experience. The details of operational experience for fuel in Canadian reactors are summarized for the period 1991-1994; excellent fuel performance has been sustained, with steady-state bundle defect rates currently as low as 0.02%. The status of introducing long 37-element bundles, and bundles with rounded bearing pads is reviewed. These minor changes in fuel design have been selectively introduced in response to operational constraints (end-plate cracking and pressure-tube fretting) at Ontario Hydro's Bruce-B and Darlington stations. The R and D programs are generating a more complete understanding of CANDU fuel behaviour, while the CANDU Owners Group (COG) Fuel Technology Program is being re-aligned to a more exclusive focus on the needs of operating stations. Technical highlights and realized benefits from the COG program are summarized. Re-organization of AECL to provide a one-company focus, with an outward looking view to new CANDU markets, has strengthened R and D in advanced fuel cycles. Progress in AECL's key fuel cycle programs is also summarized. (author)

  1. Baseline Gas Turbine Development Program. Fourteenth quarterly progress report

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, F W; Wagner, C E

    1976-04-30

    Progress is reported for a Baseline Gas Turbine Development Program sponsored by the Heat Engine Systems Branch, Division of Transportation Energy Conservation (TEC) of the Energy Research and Development Administration (ERDA). Structurally, this program is made up of three parts: (1) documentation of the existing automotive gas turbine state-of-the-art; (2) conduction of an extensive component improvement program; and (3) utilization of the improvements in the design, and building of an Upgraded Engine capable of demonstrating program goals.

  2. Overview of Faculty Development Programs for Interprofessional Education.

    Science.gov (United States)

    Ratka, Anna; Zorek, Joseph A; Meyer, Susan M

    2017-06-01

    Objectives. To describe characteristics of faculty development programs designed to facilitate interprofessional education, and to compile recommendations for development, delivery, and assessment of such faculty development programs. Methods. MEDLINE, CINAHL, ERIC, and Web of Science databases were searched using three keywords: faculty development, interprofessional education, and health professions. Articles meeting inclusion criteria were analyzed for emergent themes, including program design, delivery, participants, resources, and assessment. Results. Seventeen articles were identified for inclusion, yielding five characteristics of a successful program: institutional support; objectives and outcomes based on interprofessional competencies; focus on consensus-building and group facilitation skills; flexibility based on institution- and participant-specific characteristics; and incorporation of an assessment strategy. Conclusion. The themes and characteristics identified in this literature overview may support development of faculty development programs for interprofessional education. An advanced evidence base for interprofessional education faculty development programs is needed.

  3. Computer Aided Design System for Developing Musical Fountain Programs

    Institute of Scientific and Technical Information of China (English)

    刘丹; 张乃尧; 朱汉城

    2003-01-01

    A computer aided design system for developing musical fountain programs was developed with multiple functions such as intelligent design, 3-D animation, manual modification and synchronized motion to make the development process more efficient. The system first analyzed the music form and sentiment using many basic features of the music to select a basic fountain program. Then, this program is simulated with 3-D animation and modified manually to achieve the desired results. Finally, the program is transformed to a computer control program to control the musical fountain in time with the music. A prototype system for the musical fountain was also developed. It was tested with many styles of music and users were quite satisfied with its performance. By integrating various functions, the proposed computer aided design system for developing musical fountain programs greatly simplified the design of the musical fountain programs.

  4. Japan's Sunshine Project. Summary of solar energy research and development program (1983 edition)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-07-01

    The Sunshine Program is managed by the promotion center established by the Agency of Industrial Science and Technology of the Ministry of International Trade and Ministry, and is allocated for fiscal 1983 a budget of 8.9 times 1-billion yen. The program is to come to a conclusion in 2000. The program covers not only photovoltaic power generation but also many other fields in which research and development efforts bear fruits of success in practical application one after the other. At the current stage, the target is the test run of a crystalline solar cell mass production line (500kW/year). Basic studies and development will also proceed for the practicalization of amorphous solar cells. For photovoltaic power generation, four demonstration systems and two central power plants will be constructed and operated. Two solar thermal power generation systems each capable of 1000kWe will be tested and operated. Solar systems will be constructed and operated for industrial process heating. Articles on photovoltaic power generation in this book cover the basic study of solar cells, development of crystalline/amorphous solar cells, development of mass production technology, and development of system technology. Reference is also made to the state of development of solar thermal power generation and solar thermal heating/cooling. (NEDO)

  5. State Space Formulation of Nonlinear Vibration Responses Collected from a Dynamic Rotor-Bearing System: An Extension of Bearing Diagnostics to Bearing Prognostics.

    Science.gov (United States)

    Tse, Peter W; Wang, Dong

    2017-02-14

    Bearings are widely used in various industries to support rotating shafts. Their failures accelerate failures of other adjacent components and may cause unexpected machine breakdowns. In recent years, nonlinear vibration responses collected from a dynamic rotor-bearing system have been widely analyzed for bearing diagnostics. Numerous methods have been proposed to identify different bearing faults. However, these methods are unable to predict the future health conditions of bearings. To extend bearing diagnostics to bearing prognostics, this paper reports the design of a state space formulation of nonlinear vibration responses collected from a dynamic rotor-bearing system in order to intelligently predict bearing remaining useful life (RUL). Firstly, analyses of nonlinear vibration responses were conducted to construct a bearing health indicator (BHI) so as to assess the current bearing health condition. Secondly, a state space model of the BHI was developed to mathematically track the health evolution of the BHI. Thirdly, unscented particle filtering was used to predict bearing RUL. Lastly, a new bearing acceleration life testing setup was designed to collect natural bearing degradation data, which were used to validate the effectiveness of the proposed bearing prognostic method. Results show that the prediction accuracy of the proposed bearing prognostic method is promising and the proposed bearing prognostic method is able to reflect future bearing health conditions.

  6. State Space Formulation of Nonlinear Vibration Responses Collected from a Dynamic Rotor-Bearing System: An Extension of Bearing Diagnostics to Bearing Prognostics

    Directory of Open Access Journals (Sweden)

    Peter W. Tse

    2017-02-01

    Full Text Available Bearings are widely used in various industries to support rotating shafts. Their failures accelerate failures of other adjacent components and may cause unexpected machine breakdowns. In recent years, nonlinear vibration responses collected from a dynamic rotor-bearing system have been widely analyzed for bearing diagnostics. Numerous methods have been proposed to identify different bearing faults. However, these methods are unable to predict the future health conditions of bearings. To extend bearing diagnostics to bearing prognostics, this paper reports the design of a state space formulation of nonlinear vibration responses collected from a dynamic rotor-bearing system in order to intelligently predict bearing remaining useful life (RUL. Firstly, analyses of nonlinear vibration responses were conducted to construct a bearing health indicator (BHI so as to assess the current bearing health condition. Secondly, a state space model of the BHI was developed to mathematically track the health evolution of the BHI. Thirdly, unscented particle filtering was used to predict bearing RUL. Lastly, a new bearing acceleration life testing setup was designed to collect natural bearing degradation data, which were used to validate the effectiveness of the proposed bearing prognostic method. Results show that the prediction accuracy of the proposed bearing prognostic method is promising and the proposed bearing prognostic method is able to reflect future bearing health conditions.

  7. 7 CFR 761.53 - Interest bearing accounts.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 7 2010-01-01 2010-01-01 false Interest bearing accounts. 761.53 Section 761.53... AGRICULTURE SPECIAL PROGRAMS GENERAL PROGRAM ADMINISTRATION Supervised Bank Accounts § 761.53 Interest bearing accounts. (a) A supervised bank account, if possible, will be established as an interest bearing deposit...

  8. Developing a hazmat incident evaluation program

    International Nuclear Information System (INIS)

    Williams, D.L.; Kaikumba, F.

    1991-01-01

    This paper reports that all communities are at risk of experiencing a hazardous materials incident, whether in transportation or at a fixed facility (such as petroleum refineries, oil fields, processing plants, etc.). However, many communities are unprepared to cope with this emergency. Administrators of state agencies and local response organizations often face fierce competition for tax dollars in support of their hazardous materials emergency response programs. Historically, little statistical information has been available to support their call for additional budget dollars in the areas of personnel, training, and equipment. It is difficult to plan for an emergency when you have little understanding of the risks, the frequency of incidents, the type of chemicals generally involved, and other vital information. The Illinois Hazardous Materials Incident Evaluation Program was designed to address the state and local needs, and position government and industry in a more responsive and proactive mode. The result is a program that works

  9. Eastern slopes grizzly bear project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-01-01

    The cumulative effects of human activities on the grizzly bears in the central Canadian Rockies are not well known. As a result, a project was initiated in 1994 to address the urgent requirement for accurate scientific information on the habitat and populations of grizzly bears in the area of the Banff National Park and Kananaskis Country. This area is probably the most heavily used and developed area where the grizzly still survives. The information gathered throughout the course of this study will be used to better protect and manage the bears and other sensitive carnivores in the region. Using telemetry, researchers are monitoring 25 grizzly bears which were radio-collared in a 22,000 square-kilometer area in the upper Bow Valley drainage of the eastern Alberta slopes. The researchers involved in the project are working with representatives from Husky Oil and Talisman Energy on the sound development of the Moose Mountain oil and gas field without adversely affecting the grizzly bear population. Information collected over seven years indicated that the grizzly bears have few and infrequent offspring. Using the information gathered so far, the location of the Moose Mountain to Jumping Pound pipeline was carefully selected, since the bears recover very slowly from high mortality, and also considering that the food and cover had already been compromised by the high number of roads, trails and other human activities in the area. The status of the population and habitat of the grizzly bear will be assessed upon the conclusion of the field research phase in 2001. Models will be updated using the data obtained during eight years and will assist in the understanding of complex variables that affect grizzly bears.

  10. Disease-Specific Care: Spine Surgery Program Development.

    Science.gov (United States)

    Koerner, Katie; Franker, Lauren; Douglas, Barbara; Medero, Edgardo; Bromeland, Jennifer

    2017-10-01

    Minimal literature exists describing the process for development of a Joint Commission comprehensive spine surgery program within a community hospital health system. Components of a comprehensive program include structured communication across care settings, preoperative education, quality outcomes tracking, and patient follow-up. Organizations obtaining disease-specific certification must have clear knowledge of the planning, time, and overall commitment, essential to developing a successful program. Health systems benefit from disease-specific certification because of their commitment to a higher standard of service. Certification standards establish a framework for organizational structure and management and provide institutions a competitive edge in the marketplace. A framework for the development of a spine surgery program is described to help guide organizations seeking disease-specific certification. In developing a comprehensive program, it is critical to define the program's mission and vision, identify key stakeholders, implement clinical practice guidelines, and evaluate program outcomes.

  11. Environmental Biotechnology Research and Development Program 1989-1992

    OpenAIRE

    Brinkman J; Rulkens WH; Visscher K

    1989-01-01

    This report is an English translation of the Dutch Research and Development Program on environmental biotechnology 1989-1992. In this program an overview is given of the recent developments in environmental biotechnology. Based on this overview, the possibilities of biotechnology for management of the environment are evaluated. In this program two kinds of research are distinguished. Applied research directly focusses on specific environmental problems. Fundamental research aims at developing...

  12. Passive magnetic bearing configurations

    Science.gov (United States)

    Post, Richard F [Walnut Creek, CA

    2011-01-25

    A journal bearing provides vertical and radial stability to a rotor of a passive magnetic bearing system when the rotor is not rotating and when it is rotating. In the passive magnetic bearing system, the rotor has a vertical axis of rotation. Without the journal bearing, the rotor is vertically and radially unstable when stationary, and is vertically stable and radially unstable when rotating.

  13. Economic efficiency in forest service program development

    Science.gov (United States)

    Robert J. Hrubes

    1984-01-01

    This report analyzes the procedures used in three regions of the Forest Service, U.S. Department of Agriculture, for selecting the projects that constitute their annual program budget. Personnel at the Southwest (R-3), Pacific Southwest (R-5), and Southern (R-8) Regions were interviewed during September and October 1982. Of special concern was the extent to which...

  14. Global Studies: Hurdles to Program Development

    Science.gov (United States)

    Campbell, Patricia J.; Masters, Paul E.; Goolsby, Amy

    2004-01-01

    In this article, we examine a new global studies program that departs from the traditional state-centric approach and uses a geocentric, or earth-centered, approach that emphasizes the roles of individuals, grassroots organizations, cultural groups, and international organizations in an attempt to help students conceptualize global events and…

  15. Research and development program, fiscal year 1974

    Energy Technology Data Exchange (ETDEWEB)

    1972-04-01

    The biomedical program of the Laboratory of Nuclear Medicine and Radiation Biology for Fiscal Year 1974 is conducted within the scope of the following categories: Effects of Radiation of Living Organisms; Molecular and Cellular Radiobiology; Land and Fresh Water Environmental Sciences; Radiological and Health Physics and Instrumentation; and Nuclear Medical Research. (ACR)

  16. Higher Education Leadership Graduate Program Development

    Science.gov (United States)

    Freeman, Sydney, Jr.; Chambers, Crystal Renée; Newton, Rochelle

    2016-01-01

    Graduate programs in higher education administration and leadership have sought to equip students with the knowledge, skills, and competencies for higher education leadership; that is, to prepare globally minded leaders who can navigate the internal and external demands of, and for, higher education. With the use of the Lattuca and Stark model of…

  17. Scaling laws for radial foil bearings

    Science.gov (United States)

    Honavara Prasad, Srikanth

    The effects of fluid pressurization, structural deformation of the compliant members and heat generation in foil bearings make the design and analysis of foil bearings very complicated. The complex fluid-structural-thermal interactions in foil bearings also make modeling efforts challenging because these phenomena are governed by highly non-linear partial differential equations. Consequently, comparison of various bearing designs require detailed calculation of the flow fields (velocities, pressures), bump deflections (structural compliance) and heat transfer phenomena (viscous dissipation in the fluid, frictional heating, temperature profile etc.,) resulting in extensive computational effort (time/hardware). To obviate rigorous computations and aid in feasibility assessments of foil bearings of various sizes, NASA developed the "rule of thumb" design guidelines for estimation of journal bearing load capacity. The guidelines are based on extensive experimental data. The goal of the current work is the development of scaling laws for radial foil bearings to establish an analytical "rule of thumb" for bearing clearance and bump stiffness. The use of scale invariant Reynolds equation and experimentally observed NASA "rule of thumb" yield scale factors which can be deduced from first principles. Power-law relationships between: a. Bearing clearance and bearing radius, and b. bump stiffness and bearing radius, are obtained. The clearance and bump stiffness values obtained from scaling laws are used as inputs for Orbit simulation to study various cases. As the clearance of the bearing reaches the dimensions of the material surface roughness, asperity contact breaks the fluid film which results in wear. Similarly, as the rotor diameter increases (requiring larger bearing diameters), the load capacity of the fluid film should increase to prevent dry rubbing. This imposes limits on the size of the rotor diameter and consequently bearing diameter. Therefore, this thesis aims

  18. SHABERTH - ANALYSIS OF A SHAFT BEARING SYSTEM (CRAY VERSION)

    Science.gov (United States)

    Coe, H. H.

    1994-01-01

    The SHABERTH computer program was developed to predict operating characteristics of bearings in a multibearing load support system. Lubricated and non-lubricated bearings can be modeled. SHABERTH calculates the loads, torques, temperatures, and fatigue life for ball and/or roller bearings on a single shaft. The program also allows for an analysis of the system reaction to the termination of lubricant supply to the bearings and other lubricated mechanical elements. SHABERTH has proven to be a valuable tool in the design and analysis of shaft bearing systems. The SHABERTH program is structured with four nested calculation schemes. The thermal scheme performs steady state and transient temperature calculations which predict system temperatures for a given operating state. The bearing dimensional equilibrium scheme uses the bearing temperatures, predicted by the temperature mapping subprograms, and the rolling element raceway load distribution, predicted by the bearing subprogram, to calculate bearing diametral clearance for a given operating state. The shaft-bearing system load equilibrium scheme calculates bearing inner ring positions relative to the respective outer rings such that the external loading applied to the shaft is brought into equilibrium by the rolling element loads which develop at each bearing inner ring for a given operating state. The bearing rolling element and cage load equilibrium scheme calculates the rolling element and cage equilibrium positions and rotational speeds based on the relative inner-outer ring positions, inertia effects, and friction conditions. The ball bearing subprograms in the current SHABERTH program have several model enhancements over similar programs. These enhancements include an elastohydrodynamic (EHD) film thickness model that accounts for thermal heating in the contact area and lubricant film starvation; a new model for traction combined with an asperity load sharing model; a model for the hydrodynamic rolling and

  19. Developing a Teenage Pregnancy Program the Community Will Accept.

    Science.gov (United States)

    Harris, David; And Others

    1983-01-01

    Reacting to community opposition to a pregnancy prevention program, the Suffolk County, New York, health department assessed community needs and values to develop a program that would be acceptable. The program focuses on informing parents about teenage sexual problems and emphasizes parent-child communication. (PP)

  20. Development of Transition Programs for Adolescents with Serious Emotional Disturbances.

    Science.gov (United States)

    Bulen, Julia; Bullis, Michael

    This paper reports on an ongoing 3-year project which has worked with three school sites to identify program and staff needs and then develop a tailored intervention to improve program services for adolescent students with severe emotional disturbances (SED). Necessary characteristics of effective transition programs for this population are…

  1. Developing an Online Certification Program for Nutrition Education Assistants

    Science.gov (United States)

    Christofferson, Debra; Christensen, Nedra; LeBlanc, Heidi; Bunch, Megan

    2012-01-01

    Objective: To develop an online certification program for nutrition education paraprofessionals to increase knowledge and confidence and to overcome training barriers of programming time and travel expenses. Design: An online interactive certification course based on Supplemental Nutrition Assistance Program-Education and Expanded Food and…

  2. Enhancing Agency through Leadership Development Programs for Faculty

    Science.gov (United States)

    Templeton, Lindsey; O'Meara, KerryAnn

    2018-01-01

    The ADVANCE Leadership Fellows Program at the University of Maryland is a yearlong professional development program for faculty aspiring to or recently engaged in leadership roles. Data shows an increase in participants' sense of agency to become academic leaders following the program. We use a comprehensive data set, including program…

  3. Development of conversion programs for formats of thermodynamic databases

    International Nuclear Information System (INIS)

    Yoshida, Yasushi; Yui, Mikazu

    2003-02-01

    Programs which enable to convert the database format from PHREEQE code to PHREEQC, EQ3/6 and Geochemist's Workbench code were developed and quality of these programs was checked. As a result, it was confirmed that these programs converted the database format correctly except for specific conditions which lead errors. (author)

  4. Development and Operation of a Voluntary Audit Program.

    Science.gov (United States)

    Murphy, Jerome R.

    This report describes a voluntary audit program implemented by the Educational Testing Service (ETS). The comprehensive audit program was developed to assure that all corporate programs adhere to the ETS Standards for Quality and Fairness. The standards address issues which relate to all ETS activities such as accountability, confidentiality of…

  5. Molecular control of normal and acrocona mutant seed cone development in Norway spruce (Picea abies) and the evolution of conifer ovule-bearing organs.

    Science.gov (United States)

    Carlsbecker, Annelie; Sundström, Jens F; Englund, Marie; Uddenberg, Daniel; Izquierdo, Liz; Kvarnheden, Anders; Vergara-Silva, Francisco; Engström, Peter

    2013-10-01

    Reproductive organs in seed plants are morphologically divergent and their evolutionary history is often unclear. The mechanisms controlling their development have been extensively studied in angiosperms but are poorly understood in conifers and other gymnosperms. Here, we address the molecular control of seed cone development in Norway spruce, Picea abies. We present expression analyses of five novel MADS-box genes in comparison with previously identified MADS and LEAFY genes at distinct developmental stages. In addition, we have characterized the homeotic transformation from vegetative shoot to female cone and associated changes in regulatory gene expression patterns occurring in the acrocona mutant. The analyses identified genes active at the onset of ovuliferous and ovule development and identified expression patterns marking distinct domains of the ovuliferous scale. The reproductive transformation in acrocona involves the activation of all tested genes normally active in early cone development, except for an AGAMOUS-LIKE6/SEPALLATA (AGL6/SEP) homologue. This absence may be functionally associated with the nondeterminate development of the acrocona ovule-bearing scales. Our morphological and gene expression analyses give support to the hypothesis that the modern cone is a complex structure, and the ovuliferous scale the result of reductions and compactions of an ovule-bearing axillary short shoot in cones of Paleozoic conifers. © 2013 The Authors. New Phytologist © 2013 New Phytologist Trust.

  6. AECL's research and development program in environmental science and technology

    International Nuclear Information System (INIS)

    Cornett, R.J.

    1998-07-01

    AECL's radiological research and development (R and D) program encompasses work on sources of radiation exposure, radionuclide transport through the environment and potential impacts on biota and on human health. The application of the radiation protection knowledge and technology developed in this program provides cradle-to-grave management for CANDU and related nuclear technologies. This document provides an overview of the Environmental Science and Technology (ES and T) program which is one of the technical areas of R and D within the radiological R and D program. The ES and T program uses science from three main areas: radiochemistry, mathematical modelling and environmental assessment. In addition to providing an overview of the program, this summary also gives specific examples of recent technical work in each of the three areas. These technical examples illustrate the applied nature of the ES and T program and the close coupling of the program to CANDU customer requirements. (author)

  7. Biofuels Feedstock Development Program annual progress report for 1991

    Energy Technology Data Exchange (ETDEWEB)

    Wright, L.L.; Cushman, J.H.; Ehrenshaft, A.R.; McLaughlin, S.B.; McNabb, W.A.; Ranney, J.W.; Tuskan, G.A.; Turhollow, A.F.

    1992-12-01

    This report provides an overview of the ongoing research funded in 1991 by the Department of Energy`s Biofuels Feedstock Development Program (BFDP). The BFDP is managed by the Environmental Sciences Division of the Oak Ridge National Laboratory and encompasses the work formerly funded by the Short Rotation Woody Crops Program and the Herbaceous Energy Crops Program. The combined program includes crop development research on both woody and herbaceous energy crop species, cross-cutting energy and environmental analysis and integration, and information management activities. Brief summaries of 26 different program activities are included in the report.

  8. Biofuels Feedstock Development Program annual progress report for 1991

    Energy Technology Data Exchange (ETDEWEB)

    Wright, L.L.; Cushman, J.H.; Ehrenshaft, A.R.; McLaughlin, S.B.; McNabb, W.A.; Ranney, J.W.; Tuskan, G.A.; Turhollow, A.F.

    1992-12-01

    This report provides an overview of the ongoing research funded in 1991 by the Department of Energy's Biofuels Feedstock Development Program (BFDP). The BFDP is managed by the Environmental Sciences Division of the Oak Ridge National Laboratory and encompasses the work formerly funded by the Short Rotation Woody Crops Program and the Herbaceous Energy Crops Program. The combined program includes crop development research on both woody and herbaceous energy crop species, cross-cutting energy and environmental analysis and integration, and information management activities. Brief summaries of 26 different program activities are included in the report.

  9. Bears and pipeline construction in Alaska

    Energy Technology Data Exchange (ETDEWEB)

    Follmann, E.H.; Hechtel, J.L. (Univ. of Alaska Fairbanks, AK (USA))

    1990-06-01

    Serious problems were encountered with bears during construction of the 1274-km trans-Alaska oil pipeline between Prudhoe Bay and Valdez. This multi-billion-dollar project traversed both black bear (Ursus americanus Pallas) and grizzly bear (U. arctos L.) habitat throughtout its entire length. Plans for dealing with anticipated problems with bears were often inadequate. Most (71%) problems occurred north of the Yukon River in a previously roadless wilderness where inadequate refuse disposal and widespread animal feeding created dangerous situations. Of the 192 officially reported bear problems associated with the Trans-Alaska Pipeline System (TAPS) (1971-1979), about 65% involved the presence of bears in camps or dumps, 13% the feeding of bears on garbage or handouts, 10% property damage or economic loss, 7% bears under and in buildings, and only 5% charges by bears. Remarkably, no bear-related injuries were reported, suggesting that bears became accustomed to people and did not regard them as a threat. Following construction of the TAPS there have been proposals for pipelines to transport natural gas from Prudhoe Bay to southern and Pacific-rim markets. Based on past experience, some animal control measures were developed during the planning phase for the authorized gas pipeline route in Alaska. Fences installed around 100-person survey camps were found to be effective in deterring bears in two traditionally troublesome areas. 16 refs., 7 figs., 1 tab.

  10. Laboratory Directed Research and Development Program

    International Nuclear Information System (INIS)

    1994-02-01

    This report is compiled from annual reports submitted by principal investigators following the close of fiscal year 1993. This report describes the projects supported and summarizes their accomplishments. The program advances the Laboratory's core competencies, foundations, scientific capability, and permits exploration of exciting new opportunities. Reports are given from the following divisions: Accelerator and Fusion Research, Chemical Sciences, Earth Sciences, Energy and Environment, Engineering, Environment -- Health and Safety, Information and Computing Sciences, Life Sciences, Materials Sciences, Nuclear Science, Physics, and Structural Biology

  11. Fast reactor development program in Russia

    International Nuclear Information System (INIS)

    Rachkov, Valery

    2013-01-01

    The large-scale NP can be developed on the basis of new generation of CNFC and FR technologies being in compliance with “natural safety” criteria. Within the FTP we are planning to develop alternative technologies with the goal to select by 2020 the best technological option for the large-scale nuclear power development in Russia in 21 century

  12. Nature vs. Nurture: Evidence for Social Learning of Conflict Behaviour in Grizzly Bears.

    Directory of Open Access Journals (Sweden)

    Andrea T Morehouse

    Full Text Available The propensity for a grizzly bear to develop conflict behaviours might be a result of social learning between mothers and cubs, genetic inheritance, or both learning and inheritance. Using non-invasive genetic sampling, we collected grizzly bear hair samples during 2011-2014 across southwestern Alberta, Canada. We targeted private agricultural lands for hair samples at grizzly bear incident sites, defining an incident as an occurrence in which the grizzly bear caused property damage, obtained anthropogenic food, or killed or attempted to kill livestock or pets. We genotyped 213 unique grizzly bears (118 M, 95 F at 24 microsatellite loci, plus the amelogenin marker for sex. We used the program COLONY to assign parentage. We evaluated 76 mother-offspring relationships and 119 father-offspring relationships. We compared the frequency of problem and non-problem offspring from problem and non-problem parents, excluding dependent offspring from our analysis. Our results support the social learning hypothesis, but not the genetic inheritance hypothesis. Offspring of problem mothers are more likely to be involved in conflict behaviours, while offspring from non-problem mothers are not likely to be involved in incidents or human-bear conflicts themselves (Barnard's test, p = 0.05, 62.5% of offspring from problem mothers were problem bears. There was no evidence that offspring are more likely to be involved in conflict behaviour if their fathers had been problem bears (Barnard's test, p = 0.92, 29.6% of offspring from problem fathers were problem bears. For the mother-offspring relationships evaluated, 30.3% of offspring were identified as problem bears independent of their mother's conflict status. Similarly, 28.6% of offspring were identified as problem bears independent of their father's conflict status. Proactive mitigation to prevent female bears from becoming problem individuals likely will help prevent the perpetuation of conflicts through social

  13. Nature vs. Nurture: Evidence for Social Learning of Conflict Behaviour in Grizzly Bears.

    Science.gov (United States)

    Morehouse, Andrea T; Graves, Tabitha A; Mikle, Nate; Boyce, Mark S

    2016-01-01

    The propensity for a grizzly bear to develop conflict behaviours might be a result of social learning between mothers and cubs, genetic inheritance, or both learning and inheritance. Using non-invasive genetic sampling, we collected grizzly bear hair samples during 2011-2014 across southwestern Alberta, Canada. We targeted private agricultural lands for hair samples at grizzly bear incident sites, defining an incident as an occurrence in which the grizzly bear caused property damage, obtained anthropogenic food, or killed or attempted to kill livestock or pets. We genotyped 213 unique grizzly bears (118 M, 95 F) at 24 microsatellite loci, plus the amelogenin marker for sex. We used the program COLONY to assign parentage. We evaluated 76 mother-offspring relationships and 119 father-offspring relationships. We compared the frequency of problem and non-problem offspring from problem and non-problem parents, excluding dependent offspring from our analysis. Our results support the social learning hypothesis, but not the genetic inheritance hypothesis. Offspring of problem mothers are more likely to be involved in conflict behaviours, while offspring from non-problem mothers are not likely to be involved in incidents or human-bear conflicts themselves (Barnard's test, p = 0.05, 62.5% of offspring from problem mothers were problem bears). There was no evidence that offspring are more likely to be involved in conflict behaviour if their fathers had been problem bears (Barnard's test, p = 0.92, 29.6% of offspring from problem fathers were problem bears). For the mother-offspring relationships evaluated, 30.3% of offspring were identified as problem bears independent of their mother's conflict status. Similarly, 28.6% of offspring were identified as problem bears independent of their father's conflict status. Proactive mitigation to prevent female bears from becoming problem individuals likely will help prevent the perpetuation of conflicts through social learning.

  14. Nature vs. nurture: Evidence for social learning of conflict behaviour in grizzly bears

    Science.gov (United States)

    Morehouse, Andrea T.; Graves, Tabitha A.; Mikle, Nathaniel; Boyce, Mark S.

    2016-01-01

    The propensity for a grizzly bear to develop conflict behaviours might be a result of social learning between mothers and cubs, genetic inheritance, or both learning and inheritance. Using non-invasive genetic sampling, we collected grizzly bear hair samples during 2011–2014 across southwestern Alberta, Canada. We targeted private agricultural lands for hair samples at grizzly bear incident sites, defining an incident as an occurrence in which the grizzly bear caused property damage, obtained anthropogenic food, or killed or attempted to kill livestock or pets. We genotyped 213 unique grizzly bears (118 M, 95 F) at 24 microsatellite loci, plus the amelogenin marker for sex. We used the program COLONY to assign parentage. We evaluated 76 mother-offspring relationships and 119 father-offspring relationships. We compared the frequency of problem and non-problem offspring from problem and non-problem parents, excluding dependent offspring from our analysis. Our results support the social learning hypothesis, but not the genetic inheritance hypothesis. Offspring of problem mothers are more likely to be involved in conflict behaviours, while offspring from non-problem mothers are not likely to be involved in incidents or human-bear conflicts themselves (Barnard’s test, p = 0.05, 62.5% of offspring from problem mothers were problem bears). There was no evidence that offspring are more likely to be involved in conflict behaviour if their fathers had been problem bears (Barnard’s test, p = 0.92, 29.6% of offspring from problem fathers were problem bears). For the mother-offspring relationships evaluated, 30.3% of offspring were identified as problem bears independent of their mother’s conflict status. Similarly, 28.6% of offspring were identified as problem bears independent of their father’s conflict status. Proactive mitigation to prevent female bears from becoming problem individuals likely will help prevent the perpetuation of conflicts through social learning.

  15. The push-off test: development of a simple, reliable test of upper extremity weight-bearing capability.

    Science.gov (United States)

    Vincent, Joshua I; MacDermid, Joy C; Michlovitz, Susan L; Rafuse, Richard; Wells-Rowsell, Christina; Wong, Owen; Bisbee, Leslie

    2014-01-01

    Longitudinal clinical measurement study. The push-off test (POT) is a novel and simple measure of upper extremity weight-bearing that can be measured with a grip dynamometer. There are no published studies on the validity and reliability of the POT. The relationship between upper extremity self-report activity/participation and impairment measures remain an unexplored realm. The primary purpose of this study is to estimate the intra and inter-rater reliability and construct validity of the POT. The secondary purpose is to estimate the relationship between upper extremity self-report activity/participation questionnaires and impairment measures. A convenience sample of 22 patients with wrist or elbow injuries were tested for POT, wrist/elbow range of motion (ROM), isometric wrist extension strength (WES) and grip strength; and completed two self-report activity/participation questionnaires: Disability of the Arm, Shoulder and the Hand (DASH) and Work Limitations Questionnaire (WLQ-26). POT's inter and intra-rater reliability and construct validity was tested. Pearson's correlations were run between the impairment measures and self-report questionnaires to look into the relationship amongst them. The POT demonstrated high inter-rater reliability (ICC affected = 0.97; 95% C.I. 0.93-0.99; ICC unaffected = 0.85; 95% C.I. 0.68-0.94) and intra-rater reliability (ICC affected = 0.96; 95% C.I. 0.92-0.97; ICC unaffected = 0.92; 95% C.I. 0.85-0.97). The POT was correlated moderately with the DASH (r = -0.47; p = 0.03). While examining the relationship between upper extremity self-reported activity/participation questionnaires and impairment measures the strongest correlation was between the DASH and the POT (r = -0.47; p = 0.03) and none of the correlations with the other physical impairment measures reached significance. At-work disability demonstrated insignificant correlations with physical impairments. The POT test provides a reliable and easily

  16. United States Superconducting MHD Magnet Technology Development Program

    International Nuclear Information System (INIS)

    Dawson, A.M.; Marston, P.G.; Thome, R.J.; Iwasa, Y.; Tarrh, J.M.

    1981-01-01

    A three-faceted program supported by the U.S. Dep of Energy is described. These facets include basic technology development, technology transfer and construction by industry of magnets for the national MHD program. The program includes the maintenance of a large component test facility; investigation of superconductor stability and structural behavior; measurements of materials' properties at low temperatures; structural design optimization; analytical code development; cryogenic systems and power supply design. The technology transfer program is designed to bring results of technology development and design and construction effort to the entire superconducting magnet community. The magnet procurement program is responsible for developing conceptual designs of magnets needed for the national MHD program, for issuing requests for quotation, selecting vendors and supervising design, construction, installation and test of these systems. 9 refs

  17. Establishing design criteria for crankshaft thrust bearings in gasoline and diesel engines by computer simulations and experiments. Crankshaft thrust bearing design - final report; Auslegungskriterien fuer Kurbelwellenaxiallager in Otto- und Dieselmotoren durch rechnergestuetzte Simulation und experimentelle Untersuchungen. Axialgleitlagerauslegung - Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Hunsicker, W. [Fachhochschule Mannheim (Germany). Inst. fuer Tribologie; Backhaus, K. [Univ. GH Kassel (Germany). Inst. fuer Maschinenelemente und Konstruktionstechnik; Schubert, W. [KS Gleitlager GmbH, Papenburg (Germany)

    2004-07-01

    Aim of the research-project was it to increase the calculation safety of crank shaft thrust bearings in combustion engines. The project was divided in two parts: (1) A simulation program to analyze the load bearing capacity of axial bearings under mixed lubrication has been developed at the Institut fuer Maschinenelemente und Konstruktionstechnik, University of Kassel. This part of the research-project has been presented at the FVV Herbsttagung in 2003. (2) The test runs with original parts were carried out on a newly designed thrust bearing test rig at the Institut fuer Tribologie, University of Applied Sciences in Mannheim. The following presentation shows the results of part 2. The experimental results show the influence of rotational frequency, load, bearing material, lateral run-out of the tread of the crankshaft and groove pattern. These test runs will help to dimension thrust bearings more efficiently. (orig.)

  18. A study on the ultrasonic measurement for damage evaluation of power plant bearing

    International Nuclear Information System (INIS)

    Lee, Sang Guk

    2004-01-01

    For the purpose of monitoring by ultrasonic test of the ball bearing conditions in rotating machinery, a system for their diagnosis was developed. Ultrasonic technique is used to detect abnormal conditions in the bearing system. And various data such as frequency spectrum, energy and amplitude of ultrasonic signals, and ultrasonic parameters were acquired during experiments with the simulated ball bearing system. Based on the above results and practical application for power plant, algorithms and judgement criteria for diagnosis system was established. Bearing diagnosis system is composed of four parts as follows : sensing part for ultrasonic sensor and preamplifier, signal processing part for measuring frequency spectrum, energy and amplitude, interface part for connecting ultrasonic signal to PC using A/D converter, graphic display and software part for display of bearing condition and for managing of diagnosis program

  19. Automation of program model developing for complex structure control objects

    International Nuclear Information System (INIS)

    Ivanov, A.P.; Sizova, T.B.; Mikhejkina, N.D.; Sankovskij, G.A.; Tyufyagin, A.N.

    1991-01-01

    A brief description of software for automated developing the models of integrating modular programming system, program module generator and program module library providing thermal-hydraulic calcualtion of process dynamics in power unit equipment components and on-line control system operation simulation is given. Technical recommendations for model development are based on experience in creation of concrete models of NPP power units. 8 refs., 1 tab., 4 figs

  20. Developing an integrated dam safety program

    International Nuclear Information System (INIS)

    Nielsen, N. M.; Lampa, J.

    1996-01-01

    An effort has been made to demonstrate that dam safety is an integral part of asset management which, when properly done, ensures that all objectives relating to safety and compliance, profitability, stakeholders' expectations and customer satisfaction, are achieved. The means to achieving this integration of the dam safety program and the level of effort required for each core function have been identified using the risk management approach to pinpoint vulnerabilities, and subsequently to focus priorities. The process is considered appropriate for any combination of numbers, sizes and uses of dams, and is designed to prevent exposure to unacceptable risks. 5 refs., 1 tab

  1. Calculation program development for spinning reserve

    International Nuclear Information System (INIS)

    1979-01-01

    This study is about optimal holding of spinning reserve and optimal operation for it. It deals with the purpose and contents of the study, introduction of the spinning reserve electricity, speciality of the spinning reserve power, the result of calculation, analysis for limited method of optimum load, calculation of requirement for spinning reserve, analysis on measurement of system stability with summary, purpose of the analysis, cause of impact of the accident, basics on measurement of spinning reserve and conclusion. It has the reference on explanation for design of spinning reserve power program and using and trend about spinning reserve power in Korea.

  2. Supporting the Knowledge, Innovation and Development Program at ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Supporting the Knowledge, Innovation and Development Program at FORO ... limited support granted to science, technology and innovation (STI) activities in Peru ... sustainable development strategy, as it relates to knowledge and innovation.

  3. Using advanced tomography techniques to investigate the development of White Etching Cracks in a prematurely failed field bearing

    Energy Technology Data Exchange (ETDEWEB)

    Gould, Benjamin; Greco, Aaron; Stadler, Kenred; Vegter, Erik; Xiao, Xianghui

    2017-12-01

    Crack surrounded by areas of microstructural alteration deemed "White etching cracks" (WECs) lead to premature failures within a multitude applications. While the exact cause of these failures remains unknown, a large number of hypotheses exist as to how and why these cracks form. The aim of the current work is to study newly initiated WEC networks using X-ray tomography followed by selective sectioning, in an attempt to elucidate the formation mechanisms of these cracks. The results obtained show that, for the presented bearing, WECs form preferentially around multi-phase inclusions containing aluminum, manganese, and sulfur. Additionally the results support the idea that the microstructural alterations form secondary to any cracking, suggesting that the alterations are simply a symptom of a preexisting failure.

  4. American Historical Association Faculty Development Program: Planning and Implementation.

    Science.gov (United States)

    Hoffmann, Charles

    The planning and implementation processes of the Long Island Faculty Development Program are described. Originally sponsored by the American Historical Association's Faculty Development Program to improve history instruction, this project includes faculty representatives from four Long Island universities, colleges, and junior colleges. The…

  5. The Charlotte-Mecklenburg Teacher Career Development Program.

    Science.gov (United States)

    Schlechty, Phillip C.; And Others

    1985-01-01

    Effective training, evaluation, and incentives are key aspects of this school system's six-level career ladder program for teacher development. The three-pronged committee structure for planning and communication and the program's ownership by everyone involved have been vital to its successful planning and development. (DCS)

  6. Developments in the electron gun simulation program, EGUN

    International Nuclear Information System (INIS)

    Herrmannsfeldt, W.B.

    1994-11-01

    This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described

  7. Developments in the electron gun simulation program, EGUN

    Science.gov (United States)

    Herrmannsfeldt, W. B.

    1995-07-01

    This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described.

  8. Reviewing a Reading Program: Professional Development Module. Participant's Guide

    Science.gov (United States)

    Kosanovich, Marcia; Jordan, Georgia; Arndt, Elissa; Van Sciver, Mary; Wahl, Michelle; Rissman, Lila

    2008-01-01

    The Curriculum and Instructional Projects Team at the Florida Center for Reading Research (FCRR) developed "Guidelines for Reviewing a Reading Program" ("Guidelines") to assist reviewers in determining if a program is consistent with the scientific research on reading. Based on that work, the Center on Instruction Reading Strand developed this…

  9. Development of an Actuarial Science Program at Salisbury University

    Science.gov (United States)

    Wainwright, Barbara A.

    2014-01-01

    This paper focuses on the development of an actuarial science track for the mathematics major at Salisbury University (SU). A timeline from the initial investigation into such a program through the proposal and approval processes is shared for those who might be interested in developing a new actuarial program. It is wise to start small and take…

  10. Environmental Biotechnology Research and Development Program 1989-1992

    NARCIS (Netherlands)

    Brinkman J; Rulkens WH; Visscher K

    1989-01-01

    This report is an English translation of the Dutch Research and Development Program on environmental biotechnology 1989-1992. In this program an overview is given of the recent developments in environmental biotechnology. Based on this overview, the possibilities of biotechnology for management

  11. Prevalent Approaches to Professional Development in State 4-H Programs

    Science.gov (United States)

    Smith, Martin H.; Worker, Steven M.; Schmitt-McQuitty, Lynn; Meehan, Cheryl L.; Lewis, Kendra M.; Schoenfelder, Emily; Brian, Kelley

    2017-01-01

    High-quality 4-H programming requires effective professional development of educators. Through a mixed methods study, we explored professional development offered through state 4-H programs. Survey results revealed that both in-person and online delivery modes were used commonly for 4-H staff and adult volunteers; for teen volunteers, in-person…

  12. A Leadership Education and Development Program for Clinical Nurses.

    Science.gov (United States)

    Fitzpatrick, Joyce J; Modic, Mary Beth; Van Dyk, Jennifer; Hancock, K Kelly

    2016-11-01

    The Leadership Education and Development (LEAD) Program was designed to transform care at the bedside by empowering clinical nurses as leaders. The heart of LEAD was enhancing communication skills of clinical nurses with clinical colleagues and, most importantly, patients and families. Key concepts of leadership/management were included: personal awareness, personal leadership skills/abilities, leading change, leading others individually and in teams, enhancing the patient/provider experience, and the leadership role in outcomes management. A quantitative, longitudinal, survey design was used with 2 cohorts. The program consisted of six 4-hour sessions for 3 to 6 months. Leadership practices were measured before program implementation, at the end of the program, and 3 months after program completion. There were significant increases in leadership practices sustained 3 months after program completion. A range of other outcome measures was included. There is a need for additional leadership development programs for clinical nurses.

  13. Electron beam melting of bearing materials

    Energy Technology Data Exchange (ETDEWEB)

    Goldschmied, G.; Schuler, A. (Technische Univ., Vienna (Austria). Inst. fuer Allgemeine Elektrotechnik); Elsinger, G.; Koroschetz, F. (MIBA Gleitlager AG, Laakirchen (Austria)); Tschegg, E.K. (Technische Univ., Vienna (Austria). Inst. fuer Angewandte und Technische Physik)

    1990-06-01

    This paper reports on a surface treatment method for the bearing materials AlSn6 which permits the use of this material without the overlay usually required. Microstructural refinement is achieved by means of a surface melting technique using an electron beam with successive rapid solidification. Extremely fine tin precipitates are formed in the melted surface layer which lead to significantly better tribological properties of the bearing material. Tests compared the tribological properties for AlSn6 bearings treated by the surface melting technique with those of untreated bearings. Whereas all untreated bearings failed by seizure after only 2 h of testing, 30% of the tested bearings which had been surface melted survived the entire testing program without damage.

  14. Structured Coaching Programs to Develop Staff.

    Science.gov (United States)

    Dyess, Susan MacLeod; Sherman, Rose; Opalinski, Andra; Eggenberger, Terry

    2017-08-01

    Health care environments are complex and chaotic, therein challenging patients and professionals to attain satisfaction, well-being, and exceptional outcomes. These chaotic environments increase the stress and burnout of professionals and reduce the likelihood of optimizing success in many dimensions. Coaching is evolving as a professional skill that may influence the optimization of the health care environment. This article reflects on three coaching programs: Gallup Strengths-Based Coaching, Dartmouth Microsystem Coaching, and Health and Wellness Nurse Coaching. Each approach is presented, processes and outcomes are considered, and implications for educators are offered. Continuing education departments may recognize various coaching approaches as opportunities to support staff professionals achieve not only the triple aim, but also the quadruple aim. J Contin Educ Nurs. 2017;48(8):373-378. Copyright 2017, SLACK Incorporated.

  15. Senior Program Specialist | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Initiative Development Identifies opportunities that will contribute to meeting the ... internal and governance committees, in-house and external research, global ... of strengthening CRVS systems, including gaps in existing CRVS infrastructure ...

  16. Program Officer | IDRC - International Development Research Centre

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... and the regional offices on issues of project development and management; ... IDRC's contacts with other international agencies and Canadian institutions; ... including conceptual, methodological, operational, evaluative, and financial ...

  17. Senior Program Officer | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Job Summary Working as a member of one or two multi-disciplinary teams under ... and the regional offices on issues of project development and management; ... identification and administration of resource persons/consultants in support of ...

  18. Research Award: Innovation for Inclusive Development program

    International Development Research Centre (IDRC) Digital Library (Canada)

    IDRC CRDI

    2011-09-12

    Sep 12, 2011 ... students, as well as recent graduates, to enhance their research skills ... experience in development research. ... enable greater understanding of how innovation in the informal ... Innovation and women in the informal sector.

  19. Center Independent Research & Developments: JSC IRAD Program

    Data.gov (United States)

    National Aeronautics and Space Administration — JSC provides and applies its preeminent capabilities in science and technology to develop, operate, and integrate human exploration missions.  The center...

  20. Development and Implementation of a Program Management Maturity Model

    Energy Technology Data Exchange (ETDEWEB)

    Hartwig, Laura; Smith, Matt

    2008-12-15

    In 2006, Honeywell Federal Manufacturing & Technologies (FM&T) announced an updatedvision statement for the organization. The vision is “To be the most admired team within the NNSA [National Nuclear Security Administration] for our relentless drive to convert ideas into the highest quality products and services for National Security by applying the right technology, outstanding program management and best commercial practices.” The challenge to provide outstanding program management was taken up by the Program Management division and the Program Integration Office (PIO) of the company. This article describes how Honeywell developed and deployed a program management maturity model to drive toward excellence.

  1. Developing the strategic plan for pollution prevention in defense programs

    International Nuclear Information System (INIS)

    Marchetti, John A.; Betschart, James F.; Suffern, J. Samuel

    1992-01-01

    In order to provide effective leadership and to ensure a consistent pollution prevention effort in all of its production facilities and laboratories, Defense Programs (DP) Headquarters, in close cooperation with the Field, has developed a strategic plan for its Pollution Prevention Program. The strategic plan is built upon the history of waste minimization, waste reduction, and pollution prevention activity to date, and articulates both long- and short-term strategies to ensure program initiation, growth, and stability. The organization of the program, including Headquarters staffing and linkages to the Geld, is described. Life-cycle analysis of program barriers and bottlenecks, along with associated initiatives and action plans are discussed. (author)

  2. Empirical Studies of Agile Software Development to Learn Programming Skills

    Directory of Open Access Journals (Sweden)

    Yasuyo Kofune

    2014-06-01

    Full Text Available This paper presents a programming education support method based on Agile Development that encourages and builds on communication between students. Through mutual discussion, students using our approach transform their ideas into software and cooperate to write a program. The students complete the software through repetition and programming. Before completing the software program, the students learn to solve problems by working together. The students are encouraged to think and share ideas, and gain experience writing software. With this approach, students not only learn how to write programs, but also increase their logical thinking, problem-solving, and communication skills.

  3. 25 CFR 39.132 - Can a school integrate Language Development programs into its regular instructional program?

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Can a school integrate Language Development programs into... Language Development Programs § 39.132 Can a school integrate Language Development programs into its regular instructional program? A school may offer Language Development programs to students as part of its...

  4. Superconducting bearings in flywheels

    Energy Technology Data Exchange (ETDEWEB)

    Coombs, T.A.; Campbell, A.M.; Ganney, I.; Lo, W. [Cambridge Univ. (United Kingdom). Interdisciplinary Research Centre in Superconductivity (IRC); Twardowski, T. [International Energy Systems, Chester High Road, Neston, South Wirral (United Kingdom); Dawson, B. [British Nuclear Fuels, Capenhurst, South Wirral (United Kingdom)

    1998-05-01

    Investigations are being carried out into the use of superconducting magnetic bearings to levitate energy storage flywheels. In a planned program of work, Cambridge University are aiming to produce a practical bearing system for Pirouette(TM). The Pirouette(TM) system is designed to provide 5 kWh of recoverable energy which is currently recoverable at a rate of 5 kW (future revisions will provide up to 50 kW). IES (a British Nuclear Fuels subsidiary) the owners of the Pirouette(TM) machine have supplied Cambridge with a flywheel. This flywheel weighs >40 kg and is being levitated using an Evershed-type arrangement in which the superconductor is being used to stabilize the interaction between two magnets. To date we have demonstrated stable levitation in static and low speed tests in a rig designed for low speeds of rotation in air. A second rig which is currently under construction at BNFL will run in vacuum at speeds of up to 50 (orig.) 5 refs.

  5. Development of a safety and regulation systems simulation program II

    International Nuclear Information System (INIS)

    1985-05-01

    This report describes the development of a safety and regulation systems simulation program under contract to the Atomic Energy Control Board of Canada. A systems logic interaction simulation (SLISIM) program was developed for the AECB's HP-1000 computer which operates in the interactive simulation (INSIM) program environment. The SLISIM program simulates the spatial neutron dynamics, the regulation of the reactor power and in this version the CANDU-PHW 600 MW(e) computerized shutdown systems' trip parameters. The modular concept and interactive capability of the INSIM environment provides the user with considerable flexibility of the setup and control of the simulation

  6. Advanced Emissions Control Development Program: Mercury Control

    International Nuclear Information System (INIS)

    Evans, A.P.; Redinger, K.W.; Holmes, M.J.

    1997-07-01

    McDermott Technology, Inc. (a subsidiary of Babcock ampersand Wilcox) is conducting the Advanced Emissions Control Development Project (AECDP) which is aimed at the development of practical, cost-effective strategies for reducing the emissions of hazardous air pollutants (HAPS) from coal-fired electric utility plants. The need for such controls may arise as the US Environmental Protection Agency (EPA) proceeds with implementation of requirements set forth in the Clean Air Act Amendments (CAAA's) of 1990. Promulgation of air toxics emissions regulations for electric utility plants could dramatically impact utilities burning coal, their industrial and residential customers, and the coal industry. AECDP project work will supply the information needed by utilities to respond to potential HAPs regulations in a timely, cost-effective, enviromnentally-sound manner which supports the continued use of the Nation's abundant reserves of coal, such as those in the State of Ohio. The development work is being carried out using the 10 MW Clean Environment Development Facility wherein air toxics emissions control strategies can be developed under controlled conditions. The specific objectives of the project are to (1) measure and understand production and partitioning of air toxics species for a variety of coals, (2) optimize the air toxics removal performance of conventional flue gas cleanup systems, (3) develop advanced air toxics emissions control concepts, (4) develop and validate air toxics emissions measurement and monitoring techniques, and (5) establish a comprehensive, self-consistent air toxics data library. This project is supported by the Department of Energy, the Ohio Coal Development Office within the Ohio Department of Development and Babcock ampersand Wilcox. A comprehensive assessment of HAP emissions from coal-fired electric utility boilers sponsored by the Department of Energy and the Electric Power Research Institute concluded that with the exception of

  7. Developing a longitudinal cancer nursing education program in Honduras.

    Science.gov (United States)

    Sheldon, Lisa Kennedy; Wise, Barbara; Carlson, Julie R; Dowds, Cynthia; Sarchet, Vanessa; Sanchez, Jose Angel

    2013-12-01

    The present paper is a longitudinal study which aims to develop and deliver cancer nursing education conferences in Honduras using volunteer nurse educators. This program intends to (1) perform site assessments of work environments and resources for cancer care in Honduras, (2) develop cancer nursing education programs, (3) survey conference participants continuing education needs, (4) deliver cancer nursing education conferences, and (5) share data with local and global partners for future cancer programs. The study draws on a longitudinal program development with site assessments, data collection, and educational conferences at two time points. Assessments and surveys were used for conference development and delivery by volunteer nurse educators. Site assessments and conferences were delivered twice. Data were collected regarding assessments and surveys to inform program development. Survey data revealed that 65 % had internet access. Participants desired more information about handling of chemotherapy, symptom management, and palliative care. Volunteer nurse educators perform site assessments and develop educational programming for cancer nurses. Local and global partners should explore internet-based programs between site visits to create sustainable education programs.

  8. Formal behavioral evaluation of enrichment programs on a zookeeper's schedule: a case study with a polar bear (Ursus Maritimus) at the Bronx Zoo.

    Science.gov (United States)

    Canino, Wendy; Powell, David

    2010-01-01

    We conducted a brief study of the effectiveness of environmental enrichment for a polar bear at the Bronx Zoo with two objectives in mind. First we wanted to determine if a novel method of collecting data that easily fits into a zookeeper's work routine would produce usable data and if so, we wanted to evaluate the effectiveness of some new items that had been purchased for enriching the polar bear in reducing his pacing behavior. Observations were recorded for 119 days over a period of 5 months from April 2007 through August 2007. Five new items and eight previously used items were rotated and presented to the polar bear in the morning and afternoon. We recorded the bear's behavior five times per day as we passed by his exhibit during our regular work routine. Predictably, we found that the newer enrichment items were more effective at increasing play and decreasing pacing, as well as other more subtle effects on his behavior that helped us to design a better enrichment routine. More importantly, we found that this method of "multi-point scan sampling" was effective at producing ample and reliable data that could be used to analyze the bear's behavior without adding significant work to the keepers' daily routine. (c) 2009 Wiley-Liss, Inc.

  9. Practical Leader Development Program Using Emotional Intelligence

    DEFF Research Database (Denmark)

    Barfod, Jakob Rømer; Bakkegaard, Bjarne

    2017-01-01

    The Danish Army has more than ten years of experience working with developing emotional intelligence in the Royal Danish Army Officers’ Academy (RDAOA), and the Academy has developed military leaders who have benefitted from emotional intelligence training. Today many of the military leaders...... are better at understanding themselves as well as their ability to build relationships whilst under great pressure e.g. during combat operations. On the basis of field experience, qualitative research and quantitative data the effects of working with emotional intelligence in a structured way is presented...

  10. The ALIVE program: developing a web-based professional development program for nursing leaders in the home healthcare sector.

    Science.gov (United States)

    Lankshear, Sara; Huckstep, Sherri; Lefebre, Nancy; Leiterman, Janis; Simon, Deborah

    2010-05-01

    Home healthcare nurses often work in isolation and rarely have the opportunity to meet or congregate in one location. As a result, nurse leaders must possess unique leadership skills to supervise and manage a dispersed employee base from a distance. The nature of this dispersed workforce creates an additional challenge in the ability to identify future leaders, facilitate leadership capacity, and enhance skill development to prepare them for future leadership positions. The ALIVE (Actively Leading In Virtual Environments) web-based program was developed to meet the needs of leaders working in virtual environments such as the home healthcare sector. The program, developed through a partnership of three home healthcare agencies, used nursing leaders as content experts to guide program development and as participants in the pilot. Evaluation findings include the identification of key competencies for nursing leaders in the home healthcare sector, development of program learning objectives and participant feedback regarding program content and delivery.

  11. D and D technology development program

    International Nuclear Information System (INIS)

    Hyde, J.M.

    1998-01-01

    This paper describes the content of the current program of work for the Deactivation and Decommissioning Focus Area (DDFA) located in the Office of Science and Technology (EM-50). The authors began using large-scale demonstration projects (LSDPs) in 1996 to demonstrate and test innovative decommissioning and decontamination (D and D) technologies in ongoing US Department of Energy (DOE) decommissioning projects. These LSDPs have been conducted in and are planned for different types of DOE facilities such as research and production reactors; highly enriched uranium, tritium, and plutonium processing facilities; fuel reprocessing canyons; weapons production facilities; gaseous diffusion plants; hot cells; and waste processing facilities. The concept has been to focus on addressing DOE's high-priority deactivation and decommissioning needs through the LSDP strategy. In an LSDP, the focus area demonstrates improved technologies side by side with the current baseline technologies in ongoing site decommissioning projects. This approach helps reduce the risk and liability for the DOE users associated with the first-time use of a technology and promotes creative solutions that expand the D and D tool box beyond standard practices and technologies along with other benefits. As of January 1998, more than 50 technologies have been demonstrated covering the areas of characterization, decontamination, dismantlement, waste disposition, stabilization, and health and safety

  12. Department of Energy: Nuclear S&T workforce development programs

    International Nuclear Information System (INIS)

    Bingham, Michelle; Bala, Marsha; Beierschmitt, Kelly; Steele, Carolyn; Sattelberger, Alfred P.; Bruozas, Meridith A.

    2016-01-01

    The U.S. Department of Energy (DOE) national laboratories use their expertise in nuclear science and technology (S&T) to support a robust national nuclear S&T enterprise from the ground up. Traditional academic programs do not provide all the elements necessary to develop this expertise, so the DOE has initiated a number of supplemental programs to develop and support the nuclear S&T workforce pipeline. This document catalogs existing workforce development programs that are supported by a number of DOE offices (such as the Offices of Nuclear Energy, Science, Energy Efficiency, and Environmental Management), and by the National Nuclear Security Administration (NNSA) and the Naval Reactor Program. Workforce development programs in nuclear S&T administered through the Department of Homeland Security, the Nuclear Regulatory Commission, and the Department of Defense are also included. The information about these programs, which is cataloged below, is drawn from the program websites. Some programs, such as the Minority Serving Institutes Partnership Programs (MSIPPs) are available through more than one DOE office, so they appear in more than one section of this document.

  13. Effective Software Engineering Leadership for Development Programs

    Science.gov (United States)

    Cagle West, Marsha

    2010-01-01

    Software is a critical component of systems ranging from simple consumer appliances to complex health, nuclear, and flight control systems. The development of quality, reliable, and effective software solutions requires the incorporation of effective software engineering processes and leadership. Processes, approaches, and methodologies for…

  14. Map of CCAA programming | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2011-01-06

    Jan 6, 2011 ... While developed countries must cut greenhouse gas emissions to limit the dangerous impacts of climate change, it is already too late to stop the changes already in motion in the Earth's atmosphere and oceans. Africa has no choice but to adapt to a hotter, mainly drier, and increasingly unpredictable ...

  15. Next Generation Drivetrain Development and Test Program

    Energy Technology Data Exchange (ETDEWEB)

    Keller, Jonathan; Erdman, Bill; Blodgett, Doug; Halse, Chris; Grider, Dave

    2015-11-03

    This presentation was given at the Wind Energy IQ conference in Bremen, Germany, November 30 through December 2, 2105. It focused on the next-generation drivetrain architecture and drivetrain technology development and testing (including gearbox and inverter software and medium-voltage inverter modules.

  16. Tools for Nanotechnology Education Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Dorothy Moore

    2010-09-27

    The overall focus of this project was the development of reusable, cost-effective educational modules for use with the table top scanning electron microscope (TTSEM). The goal of this project's outreach component was to increase students' exposure to the science and technology of nanoscience.

  17. Motor Development Programming in Trisomic-21 Babies

    Science.gov (United States)

    Sanz, Teresa; Menendez, Javier; Rosique, Teresa

    2011-01-01

    The present study contributes to the understanding of gross motor development in babies with Down's syndrome. Also, it facilitates the comprehension of the efficiency of the early motor stimulation as well as of beginning it as early as possible. We worked with two groups of babies with Down's syndrome, beginning the early motor training in each…

  18. Implementing sustainable development programs in Chicago

    Energy Technology Data Exchange (ETDEWEB)

    Henderson, H.

    1994-12-31

    Achieving sustainable development requires a revision of the present view of the nature of the city as an environment, and its relation to a larger ecosystem of which it is an essential part. The environmental health of a wilderness area is inextricably related to the environmental, and economic, health of the great urban centers. The vitality of dense metropolitan areas, where population and economic activities are concentrated, is key to the preservation of productive farm lands, wildlife habitat, and open spaces. The social and economic crisis which grips many metropolitan centers, with attendant flight of industry and development to the so-called {open_quotes}greenfields,{close_quotes} fundamentally spreads a broader crisis to our common ecosystem. This crisis is marked by the obliteration of habitat necessary for biodiversity, loss of fertile farm land, and the contamination of air, water and land, as an unescapable effect of the sprawl created by flight from the urban centers. The removal of false conceptual distinctions between the city and nature, distinctions that are unfortunately at the heart of so much of American environmental philosophy, is key to the concept of `sustainable development.` This article sets forth how the City of Chicago is implementing this understanding of the nature of the urban environment, in pursuit of sustainable development within the city.

  19. Implementing sustainable development programs in Chicago

    International Nuclear Information System (INIS)

    Henderson, H.

    1994-01-01

    Achieving sustainable development requires a revision of the present view of the nature of the city as an environment, and its relation to a larger ecosystem of which it is an essential part. The environmental health of a wilderness area is inextricably related to the environmental, and economic, health of the great urban centers. The vitality of dense metropolitan areas, where population and economic activities are concentrated, is key to the preservation of productive farm lands, wildlife habitat, and open spaces. The social and economic crisis which grips many metropolitan centers, with attendant flight of industry and development to the so-called open-quotes greenfields,close quotes fundamentally spreads a broader crisis to our common ecosystem. This crisis is marked by the obliteration of habitat necessary for biodiversity, loss of fertile farm land, and the contamination of air, water and land, as an unescapable effect of the sprawl created by flight from the urban centers. The removal of false conceptual distinctions between the city and nature, distinctions that are unfortunately at the heart of so much of American environmental philosophy, is key to the concept of 'sustainable development.' This article sets forth how the City of Chicago is implementing this understanding of the nature of the urban environment, in pursuit of sustainable development within the city

  20. A method for developing standard patient education program

    DEFF Research Database (Denmark)

    Lura, Carolina Bryne; Hauch, Sophie Misser Pallesgaard; Gøeg, Kirstine Rosenbeck

    2018-01-01

    for developing standard digital patient education programs for patients in self-administration of blood samples drawn from CVC. The Design Science Research Paradigm was used to develop a digital patient education program, called PAVIOSY, to increase patient safety during execution of the blood sample collection...... of the educational patient system, health professionals must be engaged early in the development of content and design phase....

  1. A recommended program of tritium monitoring research and development

    International Nuclear Information System (INIS)

    Nickerson, S.B.; Gerdingh, R.F.; Penfold, K.

    1982-10-01

    This report presents recommendations for programs of research and development in tritium monitoring instrumentation. These recommendations, if implemented, will offer Canadian industry the opportunity to develop marketable instruments. The major recommendations are to assist in the development and promotion of two Chalk River Nuclear Laboratories' monitors and an Ontario Hydro monitor, and to support research and development of a surface monitor

  2. Program Development for Primary School Teachers' Critical Thinking

    Science.gov (United States)

    Boonjeam, Waraporn; Tesaputa, Kowat; Sri-ampai, Anan

    2017-01-01

    The objectives of this research were: 1) to study the elements and indicators of primary school teachers' critical thinking, 2) to study current situation, desirable situation, development technique, and need for developing the primary school teachers' critical thinking, 3) to develop the program for developing the primary school teachers'…

  3. Development of new layer systems for sliding bearings under high mechanical and tribological stress. Final report; Entwicklung neuer Schichtsysteme fuer den Einsatz bei mechanisch-tribologisch hochbeanspruchten Gleitlagern. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Mathias, M.; Herrmann, B.

    1995-12-31

    The report describes the sputtering technique as a coating method for sliding bearings of high-speed diesel engines. The project aimed at the development of a heavy-duty, wear-resistant sputtered layer on a copper-lead basis for sliding bearings. (HW) [Deutsch] Es wird berichtet ueber die Einfuehrung der Sputtertechnik als Beschichtungsverfahren fuer Gleitlager fuer schnell laufende Dieselmotoren. Ziel des Projektes war die Entwicklung einer hochbelastbaren, verschleissfesten Gleitlager-Sputterschicht auf Kupfer-Blei-Basis. (HW)

  4. Laboratory Directed Research and Development Program FY 2006 Annual Report

    Energy Technology Data Exchange (ETDEWEB)

    Sjoreen, Terrence P [ORNL

    2007-04-01

    The Oak Ridge National Laboratory (ORNL) Laboratory Directed Research and Development (LDRD) Program reports its status to the US Departmental of Energy (DOE) in March of each year. The program operates under the authority of DOE Order 413.2B, 'Laboratory Directed Research and Development' (April 19, 2006), which establishes DOE's requirements for the program while providing the Laboratory Director broad flexibility for program implementation. LDRD funds are obtained through a charge to all Laboratory programs. This report includes summaries all ORNL LDRD research activities supported during FY 2006. The associated FY 2006 ORNL LDRD Self-Assessment (ORNL/PPA-2007/2) provides financial data about the FY 2006 projects and an internal evaluation of the program's management process.

  5. GCRA review and appraisal of fuel material development programs

    International Nuclear Information System (INIS)

    1980-09-01

    The Fuel material Development Program has as its principal objective and responsibility the development of a fuel that is both economical and licensable and that, at the same time, will fulfill the required performance criteria. To accomplish this, the program is broken down into the following major fuel development task areas: development of the experimental and analytical data base for selecting, qualifying, and verifying the reference fuel design; providing the data base and developing models for evaluating fuel performance under upset and accident conditions; and developing and justifying fuel fabrication specifications which are consistent with the overall fuel performance criteria and with the fuel fabrication process capabilities

  6. Forschungszentrum Karlsruhe Technik und Umwelt. Research and development program 2002

    International Nuclear Information System (INIS)

    2001-01-01

    The five main fields of research and the activities under the R and D program 2002 are explained in great detail in five chapters with the following captions: 1. ENVIRONMENT. Programs: - Sustainable development, energy and environmental engineering (UMWELT). - Earth atmosphere and climate research (ATMO). 2. PUBLIC HEALTH. Programs: - Biomedical research (BIOMED). - Medical engineering (MEDTECH). 3. ENERGY. Programs: - Thermonuclear fusion (FUSION). - Nuclear safety (NUKLEAR). 4. KEY TECHNOLOGIES. Programs: - Microsystems engineering (MIKRO). - Nanotechnology (NANO). - Materials science (MATERIAL). - Chemical process engineering (CHEMIE). - Superconductivity (SUPRA). 5. MATTER and STRUCTURE. Program: The structure of matter (STRUKTUR). The sixth chapter presents cross-cutting activities under the program: Technology transfer and marketing (TTM). The concluding chapter lists and briefly presents the activities of the scientific and technical institutes of the Karlsruhe Research Center. (CB) [de

  7. Prototype Development of Remote Operated Hot Uniaxial Press (ROHUP) to Fabricate Advanced Tc-99 Bearing Ceramic Waste Forms - 13381

    Energy Technology Data Exchange (ETDEWEB)

    Alaniz, Ariana J.; Delgado, Luc R.; Werbick, Brett M. [University of Nevada - Las Vegas, Howard R. Hughes College of Engineering, 4505 S. Maryland Parkway, Box 454009, Las Vegas, NV 89154-4009 (United States); Hartmann, Thomas [University of Nevada - Las Vegas, Harry Reid Canter, 4505 S. Maryland Parkway, Box 454009, Las Vegas, NV 89154-4009 (United States)

    2013-07-01

    The objective of this senior student project is to design and build a prototype construction of a machine that simultaneously provides the proper pressure and temperature parameters to sinter ceramic powders in-situ to create pellets of rather high densities of above 90% (theoretical). This ROHUP (Remote Operated Hot Uniaxial Press) device is designed specifically to fabricate advanced ceramic Tc-99 bearing waste forms and therefore radiological barriers have been included in the system. The HUP features electronic control and feedback systems to set and monitor pressure, load, and temperature parameters. This device operates wirelessly via portable computer using Bluetooth{sup R} technology. The HUP device is designed to fit in a standard atmosphere controlled glove box to further allow sintering under inert conditions (e.g. under Ar, He, N{sub 2}). This will further allow utilizing this HUP for other potential applications, including radioactive samples, novel ceramic waste forms, advanced oxide fuels, air-sensitive samples, metallic systems, advanced powder metallurgy, diffusion experiments and more. (authors)

  8. Technical Leadership Development Program-Year 3

    Science.gov (United States)

    2012-08-30

    be subject to a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT...NASA6, Nokia , BAE Systems, the DoD, and the Australian government to develop our initial competency model. These models were discussed in deliverable...UNCLASSIFIED 17 solutions to pursue and why they should be built. 2. Help teams solve technical problems holistically, overcoming technical and non

  9. The European Dimension of the Global Urban Development Program

    Directory of Open Access Journals (Sweden)

    Bubenko Pavlo T.

    2017-11-01

    Full Text Available The article is aimed at studying the process of evolutionary formation of the EU Cities Development Program and analyzing the strategic instrumentarium for the urban development within the currently established EU urban policy at the present stage. The key features of the process of formation of the EU urban policy have been analyzed, the main stages of evolutionary formation of the integrated EU Cities Development Program have been defined and described. In the context of ensuring an integrated approach to the sustainable urban development and complementary positioning of urban development in the EU’s territorial development and cohesion strategies, the European Union’s normative and legal framework on urban development was researched. As a result of the conducted research, the strategic instrumentarium of implementation of the EU Cities Development Program has been systematized.

  10. Idaho Chemical Processing Plant low-level waste grout stabilization development program FY-96 status report

    International Nuclear Information System (INIS)

    Herbst, A.K.

    1996-09-01

    The general purpose of the Grout Stabilization Development Program is to solidify and stabilize the liquid low-level wastes (LLW) generated at the Idaho Chemical Processing Plant (ICPP). It is anticipated that LLW will be produced from the following: (1) chemical separation of the tank farm high-activity sodium-bearing waste; (2) retrieval, dissolution, and chemical separation of the aluminum, zirconium, and sodium calcines; (3) facility decontamination processes; and (4) process equipment waste. The main tasks completed this fiscal year as part of the program were chromium stabilization study for sodium-bearing waste and stabilization and solidification of LLW from aluminum and zirconium calcines. The projected LLW will be highly acidic and contain high amounts of nitrates. Both of these are detrimental to Portland cement chemistry; thus, methods to precondition the LLW and to cure the grout were explored. A thermal calcination process, called denitration, was developed to solidify the waste and destroy the nitrates. A three-way blend of Portland cement, blast furnace slag, and fly ash was successfully tested. Grout cubes were prepared at various waste loadings to maximize loading while meeting compressive strength and leach resistance requirements. For the sodium LLW, a 25% waste loading achieves a volume reduction of 3.5 and a compressive strength of 2,500 pounds per square inch while meeting leach, mix, and flow requirements. It was found that the sulfur in the slag reduces the chromium leach rate below regulatory limits. For the aluminum LLW, a 15% waste loading achieves a volume reduction of 8.5 and a compressive strength of 4,350 pounds per square inch while meeting leach requirements. Likewise for zirconium LLW, a 30% waste loading achieves a volume reduction of 8.3 and a compressive strength of 3,570 pounds per square inch

  11. Reviewing the development of an artificial intelligence based risk program

    International Nuclear Information System (INIS)

    Dixon, B.W.; Hinton, M.F.

    1985-01-01

    A successful application of nonconventional programming methods has been achieved in computer-assisted probabilistic risk assessment (PRA). The event tree sequence importance calculator, SQUIMP, provides for prompted data entry, generic expansion, on-line pruning, boolean reductions, and importance factor selection. SQUIMP employs constructs typically found in artificial intelligence (AI) programs. The development history of SQUIMP is outlined and its internal structure described as background for a discussion on the applicability of symbolic programming methods in PRA

  12. Clean coal technologies: Research, development, and demonstration program plan

    Energy Technology Data Exchange (ETDEWEB)

    1993-12-01

    The US Department of Energy, Office of Fossil Energy, has structured an integrated program for research, development, and demonstration of clean coal technologies that will enable the nation to use its plentiful domestic coal resources while meeting environmental quality requirements. The program provides the basis for making coal a low-cost, environmentally sound energy choice for electric power generation and fuels production. These programs are briefly described.

  13. MARC Program Research and Development: A Progress Report

    Directory of Open Access Journals (Sweden)

    Henriette D. Avram

    1969-12-01

    Full Text Available A description of some of the research and development activities at the Library of Congress to expand the capabilities of the MARC System. Gives details of the MARC processing format used by the Library and then describes programming work in three areas: 1 automatic tagging of data elements by format recognition programs; 2 file analysis by a statistical program called GENESIS; and 3 information retrieval using the MARC Retriever.

  14. Research and development program in reactor safety for NUCLEBRAS

    International Nuclear Information System (INIS)

    Pinheiro, R.B.; Resende Lobo, A.A. de; Horta, J.A.L.; Avelar Esteves, F. de; Lepecki, W.P.S.; Mohr, K.; Selvatici, E.

    1984-01-01

    With technical assistance from the IAEA, it was established recently an analytical and experimental Research and Development Program for NUCLEBRAS in the area of reactor safety. The main objectives of this program is to make possible, with low investments, the active participation of NUCLEBRAS in international PWR safety research. The analytical and experimental activities of the program are described with some detail, and the main results achieved up to now are presented. (Author) [pt

  15. Teddy Bear Stories

    DEFF Research Database (Denmark)

    van Leeuwen, Theo; Caldas-Coulthardt, Carmen

    2014-01-01

    This paper presents a semiotic analysis of a key cultural artefact, the teddy bear. After introducing the iconography of the teddy bear, it analyses different kinds of stories to show how teddy bears are endowed with meaning in everyday life: stories from children's books, reminiscenses by adults...... bears have traditionally centred on interpersonal relations within the nuclear family, but have recently been institutionalized and commercialized....

  16. Microeconomic analysis of military aircraft bearing restoration

    Science.gov (United States)

    Hein, G. F.

    1976-01-01

    The risk and cost of a bearing restoration by grinding program was analyzed. A microeconomic impact analysis was performed. The annual cost savings to U.S. Army aviation is approximately $950,000.00 for three engines and three transmissions. The capital value over an indefinite life is approximately ten million dollars. The annual cost savings for U.S. Air Force engines is approximately $313,000.00 with a capital value of approximately 3.1 million dollars. The program will result in the government obtaining bearings at lower costs at equivalent reliability. The bearing industry can recover lost profits during a period of reduced demand and higher costs.

  17. Systems Engineering Technical Leadership Development Program

    Science.gov (United States)

    2012-08-30

    a penalty for failing to comply with a collection of information if it does not display a currently valid OMB control number. 1. REPORT DATE 30 AUG...topics and elements were collected from a wide variety of sources, including NASA6, Nokia , BAE Systems, the DoD, and the Australian government to develop...WHS TOO009 RT0004 Report No. SERC-2012-TR-034-1 August 30, 2012 UNCLASSIFIED 17 solutions to pursue and why they should be built. 2. Help teams

  18. Nuclear program of Iran plans and development

    International Nuclear Information System (INIS)

    2016-01-01

    Described are the history of nuclear energy planning in Iran and the development of the Bushehr Nuclear Power Plant (BNPP-1) project and its impact on the competency building in national companies, nuclear safety infrastructure, training activities, public awareness and acceptance. The activities of Nuclear Engineering Department is also presented. In order to enhance technical support services to BNPP1 and also to use capabilities of other companies in the international arena and in line with safe and reliable operation of Bushehr Nuclear Power Plant, NPPD/TAVANA Company has attempted to make contact with many companies outside the country

  19. Groundwater Protection Program Calendar Year 1998 Evaluation of Groundwater and Surface Water Quality Data for the Bear Creek Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

    International Nuclear Information System (INIS)

    None

    1999-01-01

    This report presents an evaluation of the water quality monitoring data obtained by the Y-12 Plant Groundwater Protection Program (GWPP) in the Bear Creek Hydrogeologic Regime (Bear Creek Regime) during calendar year (CY) 1998. The Bear Creek Regime contains many confirmed and potential sources of groundwater and surface water contamination associated with the U.S. Department of Energy (DOE) Oak Ridge Y-12 Plant. Applicable provisions of DOE Order 5400.1A - General Environmental Protection Program - require evaluation of groundwater and surface water quality near the Y-12 Plant to: (1) gauge groundwater quality in areas that are, or could be, affected by plant operations, (2) determine the quality of surface water and groundwater where contaminants are most likely to migrate beyond the DOE Oak Ridge Reservation (ORR) property line, and (3) identify and characterize long-term trends in groundwater quality. The following sections of this report contain relevant background information (Section 2.0); describe the results of the respective data evaluations required under DOE Order 5400.1A (Section 3.0); summarize significant findings of each evaluation (Section 4.0); and list the technical reports and regulatory documents cited for more detailed information (Section 5.0). All of the figures (maps and trend graphs) and data tables referenced in each section are presented in Appendix A and Appendix B, respectively

  20. Groundwater Protection Program Calendar Year 1998 Evaluation of Groundwater and Surface Water Quality Data for the Bear Creek Hydrogeologic Regime at the U.S. Department of Energy Y-12 Plant, Oak Ridge, Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    None

    1999-09-01

    This report presents an evaluation of the water quality monitoring data obtained by the Y-12 Plant Groundwater Protection Program (GWPP) in the Bear Creek Hydrogeologic Regime (Bear Creek Regime) during calendar year (CY) 1998. The Bear Creek Regime contains many confirmed and potential sources of groundwater and surface water contamination associated with the U.S. Department of Energy (DOE) Oak Ridge Y-12 Plant. Applicable provisions of DOE Order 5400.1A - General Environmental Protection Program - require evaluation of groundwater and surface water quality near the Y-12 Plant to: (1) gauge groundwater quality in areas that are, or could be, affected by plant operations, (2) determine the quality of surface water and groundwater where contaminants are most likely to migrate beyond the DOE Oak Ridge Reservation (ORR) property line, and (3) identify and characterize long-term trends in groundwater quality. The following sections of this report contain relevant background information (Section 2.0); describe the results of the respective data evaluations required under DOE Order 5400.1A (Section 3.0); summarize significant findings of each evaluation (Section 4.0); and list the technical reports and regulatory documents cited for more detailed information (Section 5.0). All of the figures (maps and trend graphs) and data tables referenced in each section are presented in Appendix A and Appendix B, respectively.

  1. Laboratory Directed Research and Development Program

    International Nuclear Information System (INIS)

    Ogeka, G.J.; Romano, A.J.

    1992-12-01

    This report briefly discusses the following research: Advances in Geoexploration; Transvenous Coronary Angiography with Synchrotron X-Rays; Borehole Measurements of Global Warming; Molecular Ecology: Development of Field Methods for Microbial Growth Rate and Activity Measurements; A New Malaria Enzyme - A Potential Source for a New Diagnostic Test for Malaria and a Target for a New Antimalarial Drug; Basic Studies on Thoron and Thoron Precursors; Cloning of the cDNA for a Human Serine/Threonine Protein Kinase that is Activated Specifically by Double-Stranded DNA; Development of an Ultra-Fast Laser System for Accelerator Applications; Cluster Impact Fusion; Effect of a Bacterial Spore Protein on Mutagenesis; Structure and Function of Adenovirus Penton Base Protein; High Resolution Fast X-Ray Detector; Coherent Synchrotron Radiation Longitudinal Bunch Shape Monitor; High Grain Harmonic Generation Experiment; BNL Maglev Studies; Structural Investigations of Pt-Based Catalysts; Studies on the Cellular Toxicity of Cocaine and Cocaethylene; Human Melanocyte Transformation; Exploratory Applications of X-Ray Microscopy; Determination of the Higher Ordered Structure of Eukaryotic Chromosomes; Uranium Neutron Capture Therapy; Tunneling Microscopy Studies of Nanoscale Structures; Nuclear Techiques for Study of Biological Channels; RF Sources for Accelerator Physics; Induction and Repair of Double-Strand Breaks in the DNA of Human Lymphocytes; and An EBIS Source of High Charge State Ions up to Uranium

  2. Laboratory Directed Research and Development Program

    Energy Technology Data Exchange (ETDEWEB)

    Ogeka, G.J.; Romano, A.J.

    1992-12-01

    This report briefly discusses the following research: Advances in Geoexploration; Transvenous Coronary Angiography with Synchrotron X-Rays; Borehole Measurements of Global Warming; Molecular Ecology: Development of Field Methods for Microbial Growth Rate and Activity Measurements; A New Malaria Enzyme - A Potential Source for a New Diagnostic Test for Malaria and a Target for a New Antimalarial Drug; Basic Studies on Thoron and Thoron Precursors; Cloning of the cDNA for a Human Serine/Threonine Protein Kinase that is Activated Specifically by Double-Stranded DNA; Development of an Ultra-Fast Laser System for Accelerator Applications; Cluster Impact Fusion; Effect of a Bacterial Spore Protein on Mutagenesis; Structure and Function of Adenovirus Penton Base Protein; High Resolution Fast X-Ray Detector; Coherent Synchrotron Radiation Longitudinal Bunch Shape Monitor; High Grain Harmonic Generation Experiment; BNL Maglev Studies; Structural Investigations of Pt-Based Catalysts; Studies on the Cellular Toxicity of Cocaine and Cocaethylene; Human Melanocyte Transformation; Exploratory Applications of X-Ray Microscopy; Determination of the Higher Ordered Structure of Eukaryotic Chromosomes; Uranium Neutron Capture Therapy; Tunneling Microscopy Studies of Nanoscale Structures; Nuclear Techiques for Study of Biological Channels; RF Sources for Accelerator Physics; Induction and Repair of Double-Strand Breaks in the DNA of Human Lymphocytes; and An EBIS Source of High Charge State Ions up to Uranium.

  3. Regional Innovation System Strengthening Program (SIDa as an Exit Strategy National Community Development Program (PNPM

    Directory of Open Access Journals (Sweden)

    Teguh Narutomo

    2014-06-01

    Full Text Available The aim of this study was to evaluate the PNPM program and follow the program with SIDA Strengthening Program. The research method used is a qualitative method approach of this research through the evaluation research design that builds on the CIPP evaluation model (Context-Input-Process-Product. Since the failure of theories and models of development are too glorifies growth, makes many people turn to focus on people development, which includes requiring optimization of local resources, participation, and empowerment. Since then, "empowerment" which was introduced in Indonesia has been anesthetized and made many hopes among many parties. In 2007 started the National Program for Community Empowerment (PNPM which continue Kecamatan Development Program (KDP. PNPM 2014 which is part of the United Indonesia Cabinet Volume 2 is going to end. For that we need to look for an exit strategy program that can maintain sustainability of PNPM. Regional Innovation Systems Strengthening Program (SIDA is a program of the whole process in one system to foster innovation made between government institutions, local governments, research institutions, educational institutions, innovation support institutions, businesses, and communities in areas that have been implemented since the 2012 SIDA program is an empowerment program as well, both to the public and even empowering to all elements such as academia, private industry, government and society.

  4. Developing College English as a Second Language (ESL) Programs

    Science.gov (United States)

    Orlova, Irina A.; Kennedy, Jelane A.

    2009-01-01

    This article examines available literature on college English as a Second Language (ESL) programs. The literature available on college ESL programs falls into three categories: (1) research reports and articles, (2) recent theoretical discussions on ESL teaching, and (3) thought pieces discussing college ESL curriculum development and assessment…

  5. Economic and Workforce Development Program Annual Report, 2014

    Science.gov (United States)

    California Community Colleges, Chancellor's Office, 2014

    2014-01-01

    California's community colleges continue to play a crucial role in the state's economy by providing students with the skills and knowledge to succeed and by advancing the economic growth and global competitiveness of California and its regional economies through the Economic and Workforce Development Program (EWD). The EWD program invests in the…

  6. LBNL Laboratory Directed Research and Development Program FY2016

    Energy Technology Data Exchange (ETDEWEB)

    Ho, D.

    2017-03-01

    The Berkeley Lab Laboratory Directed Research and Development Program FY2016 report is compiled from annual reports submitted by principal investigators following the close of the fiscal year. This report describes the supported projects and summarizes their accomplishments. It constitutes a part of the LDRD program planning and documentation process that includes an annual planning cycle, project selection, implementation and review.

  7. Dance Educator Enrichment Program (DEEP): A Model for Professional Development

    Science.gov (United States)

    Sofras, Pamela Anderson; Emory-Maier, Ambre

    2005-01-01

    In 2001, North Carolina Dance Theatre, The University of North Carolina at Charlotte, and the Charlotte-Mecklenburg School system joined forces to create a multidimensional, professional development program for dance professionals (teachers and artists) in the public schools called, The Dance Educator Enrichment Program (DEEP). DEEP was designed…

  8. Laboratory Directed Research and Development Program Assessment for FY 2014

    Energy Technology Data Exchange (ETDEWEB)

    Hatton, D. [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2014-03-01

    Each year, Brookhaven National Laboratory (BNL) is required to provide a program description and overview of its Laboratory Directed Research and Development Program (LDRD) to the Department of Energy in accordance with DOE Order 413.2B dated April 19, 2006. This report fulfills that requirement.

  9. Programming Embedded Systems With C and GNU Development Tools

    CERN Document Server

    Barr, Michael

    2009-01-01

    Whether you're writing your first embedded program, designing the latest generation of hand-held whatchamacalits, or managing the people who do, this book is for you. Programming Embedded Systems will help you develop the knowledge and skills you need to achieve proficiency with embedded software.

  10. Embracing Agile methodology during DevOps Developer Internship Program

    OpenAIRE

    Patwardhan, Amol; Kidd, Jon; Urena, Tiffany; Rajgopalan, Aishwarya

    2016-01-01

    The DevOps team adopted agile methodologies during the summer internship program as an initiative to move away from waterfall. The DevOps team implemented the Scrum software development strategy to create an internal data dictionary web application. This article reports on the transition process and lessons learned from the pilot program.

  11. Developing fire management mixes for fire program planning

    Science.gov (United States)

    Armando González-Cabán; Patricia B. Shinkle; Thomas J. Mills

    1986-01-01

    Evaluating economic efficiency of fire management program options requires information on the firefighting inputs, such as vehicles and crews, that would be needed to execute the program option selected. An algorithm was developed to translate automatically dollars allocated to type of firefighting inputs to numbers of units, using a set of weights for a specific fire...

  12. The development of fast simulation program for marine reactor parameters

    International Nuclear Information System (INIS)

    Chen Zhiyun; Hao Jianli; Chen Wenzhen

    2012-01-01

    Highlights: ► The simplified physical and mathematical models are proposed for a marine reactor system. ► A program is developed with Simulink module and Matlab file. ► The program developed has the merit of easy input preparation, output processing and fast running. ► The program can be used for the fast simulation of marine reactor parameters on the operating field. - Abstract: The fast simulation program for marine reactor parameters is developed based on the Simulink simulating software according to the characteristics of marine reactor with requirement of maneuverability and acute and fast response. The simplified core physical and thermal model, pressurizer model, steam generator model, control rod model, reactivity model and the corresponding Simulink modules are established. The whole program is developed by coupling all the Simulink modules. Two typical transient processes of marine reactor with fast load increase at low power level and load rejection at high power level are adopted to verify the program. The results are compared with those of Relap5/Mod3.2 with good consistency, and the program runs very fast. It is shown that the program is correct and suitable for the fast and accurate simulation of marine reactor parameters on the operating field, which is significant to the marine reactor safe operation.

  13. Considering public confidence in developing regulatory programs

    International Nuclear Information System (INIS)

    Collins, S.J.

    2001-01-01

    In the area of public trust and in any investment, planning and strategy are important. While it is accepted in the United States that an essential part of our mission is to leverage our resources to improving Public Confidence this performance goal must be planned for, managed and measured. Similar to our premier performance goal of Maintaining Safety, a strategy must be developed and integrated with our external stake holders but with internal regulatory staff as well. In order to do that, business is to be conducted in an open environment, the basis for regulatory decisions has to be available through public documents and public meetings, communication must be done in clear and consistent terms. (N.C.)

  14. Integrating Professional Development into STEM Graduate Programs: Student-Centered Programs for Career Preparation

    Science.gov (United States)

    Lautz, L.; McCay, D.; Driscoll, C. T.; Glas, R. L.; Gutchess, K. M.; Johnson, A.; Millard, G.

    2017-12-01

    Recognizing that over half of STEM Ph.D. graduates are finding work outside of academia, a new, NSF-funded program at Syracuse University, EMPOWER (or Education Model Program on Water-Energy Research) is encouraging its graduate students to take ownership of their graduate program and design it to meet their anticipated needs. Launched in 2016, EMPOWER's goal is to prepare graduate students for careers in the water-energy field by offering targeted workshops, professional training coursework, a career capstone experience, a professional development mini-grant program, and an interdisciplinary "foundations" seminar. Through regular student feedback and program evaluation, EMPOWER has learned some important lessons this first year: career options and graduate students' interests are diverse, requiring individualized programs designed to meet the needs of prospective employers and employees; students need exposure to the range of careers in their field to provide a roadmap for designing their own graduate school experience; effective programs nurture a culture that values professional development thereby giving students permission to pursue career paths and professional development opportunities that meet their own needs and interests; and existing university resources support the effective and efficient integration of professional development activities into graduate programs. Many of the positive outcomes experienced by EMPOWER students may be achieved in departmental graduate programs with small changes to their graduate curricula.

  15. Development and characterization of magnetic iron oxide nanoparticles with a cisplatin-bearing polymer coating for targeted drug delivery

    Directory of Open Access Journals (Sweden)

    Unterweger H

    2014-08-01

    Full Text Available Harald Unterweger,1 Rainer Tietze,1 Christina Janko,1 Jan Zaloga,1 Stefan Lyer,1 Stephan Dürr,1 Nicola Taccardi,2 Ourania-Menti Goudouri,3 Alexander Hoppe,3 Dietmar Eberbeck,4 Dirk W Schubert,5 Aldo R Boccaccini,3 Christoph Alexiou1 1ENT Department, Section of Experimental Oncology and Nanomedicine (SEON, Else Kroener-Fresenius-Stiftung-Professorship, University Hospital Erlangen, 2Chair of Chemical Engineering I (Reaction Engineering, 3Institute of Biomaterials, Department of Materials Science and Engineering, University Erlangen-Nuremberg, Erlangen, 4Physikalisch-Technische Bundesanstalt, Berlin, 5Institute of Polymer Materials, Department of Materials Science and Engineering, University Erlangen-Nuremberg, Erlangen, Germany Abstract: A highly selective and efficient cancer therapy can be achieved using magnetically directed superparamagnetic iron oxide nanoparticles (SPIONs bearing a sufficient amount of the therapeutic agent. In this project, SPIONs with a dextran and cisplatin-bearing hyaluronic acid coating were successfully synthesized as a novel cisplatin drug delivery system. Transmission electron microscopy images as well as X-ray diffraction analysis showed that the individual magnetite particles were around 4.5 nm in size and monocrystalline. The small crystallite sizes led to the superparamagnetic behavior of the particles, which was exemplified in their magnetization curves, acquired using superconducting quantum interference device measurements. Hyaluronic acid was bound to the initially dextran-coated SPIONs by esterification. The resulting amide bond linkage was verified using Fourier transform infrared spectroscopy. The additional polymer layer increased the vehicle size from 22 nm to 56 nm, with a hyaluronic acid to dextran to magnetite weight ratio of 51:29:20. A maximum payload of 330 µg cisplatin/mL nanoparticle suspension was achieved, thus the particle size was further increased to around 77 nm with a zeta

  16. Evaluation assessment of Rail Freight Transportation Research and Development Program

    Energy Technology Data Exchange (ETDEWEB)

    1983-02-01

    This report presents an evaluation assessment of the Canadian Rail Freight Transportation Research and Development (R and D) Program. The assessment was to assist in preparing for an evaluation of the Program and to stimulate a better understanding of the broader issues and problems of evaluating R and D programs. In general, the objectives of the program are aimed at improving rail freight productivity, capacity, safety, cost, and the domestic and foreign competitive position of railway suppliers. This is to be acccomplished by stimulating a stronger industry commitment to R and D and inducing investment in new technology through joint federal-industry funding and participation in rail freight R and D projects. In view of the low funding levels of the Program, it is unlikely that it will have a significant direct impact upon these ultimate objectives. Impacts will likely only be achieved through the Program's ability to stimulate increased industrial R and D and investment in new technology. A model of the Program developed in the report shows that the critical linkages between the activities and objectives of the Program are the leadership or advocacy functions performed by the Program's managers and of the results of projects supported under the Program; and the processes of program planning and project selection. An assessment of the Program's structure indicates that there are no significant issues that would make the evaluation of the Program or its major components inadvisable. Twelve potential evaluation questions and the basic approaches required to address each of them are presented in the report. 5 figs., 10 tabs.

  17. The development of quality assurance program for cyberknife

    International Nuclear Information System (INIS)

    Jang, Ji Sun; Lee, Dong Han; Kang, Young Nam

    2006-01-01

    Standardization quality assurance (QA)program of Cyberknife for suitable circumstances in Korea has not been established. In this research, we investigated the development of QA program for Cyberknife and evaluation of the feasibility under applications. Considering the feature of constitution for systems and the therapeutic methodology of Cyberknife, the list of quality control (QC) was established and divided dependent on the each period of operations. And then all these developed QC lists were categorized into three groups such as basic QC, delivery specific QC, and patient specific QC based on the each purpose of QA. In order to verify the validity of the established QA program, this QC lists was applied to two Cyberknife centers. The acceptable tolerance was based on the undertaking inspection list from the Cyberknife manufacturer and the QC results during last three years of two Cyberknife centers in Korea. The acquired measurement results were evaluated for the analysis of the current QA status and the verification of the propriety for the developed QA program. The current QA status of two Cyberknife centers was evaluated from the accuracy of all measurements in relation with application of the established QA program. Each measurement result was verified having a good agreement within the acceptable tolerance limit of the developed QA program. It is considered that the developed QA program in this research could be established the standardization of QC methods for Cyberknife and confirmed the accuracy and stability for the image-guided stereotactic radiotherapy

  18. Cross software for microprocessor program development at CERN

    International Nuclear Information System (INIS)

    Eicken, H. von; Montuelle, J.; Willers, I.; Blake, J.

    1981-01-01

    Programs for a variety of microprocessors (including Intel 8080; Motorola 6800 and 6809 and 68000; and Texas Instruments 9900) can be prepared on different host computers (such as IBM 370, CDC 6000, and Nord 10) using portable programs developed at CERN. The range of cross software consists of: an assembler for each target microprocessor, a single linkage editor, a single object module librarian, and a variety of pre-loaders which convert object modules from CERN's format (CUFOM) into manufacturers' formats. The programs are written in BCPL and PASCAL, programming languages which are available on a wide range of computers. (orig.)

  19. A Learning Tool and Program Development for Mechatronics Design Education

    Science.gov (United States)

    Iribe, Masatsugu; Shirahata, Akihiro; Kita, Hiromasa; Sasashige, Yousuke; Dasai, Ryoichi

    In this paper we propose a new type educational program for Mechatronics design which contributes to develop the physical sense and problem solving ability of the students who study Mechatronics design. For this program we provide a new handicraft kit of 4-wheeled car which is composed of inexpensive and commonplace parts, and the performance of the assembled 4-wheeled car is sensitive to its assembly arrangement. And then we implemented this program with the handicraft kit to the university freshmen, and verified its effectiveness, and report the results of the program.

  20. Developing robotic behavior using a genetic programming model

    International Nuclear Information System (INIS)

    Pryor, R.J.

    1998-01-01

    This report describes the methodology for using a genetic programming model to develop tracking behaviors for autonomous, microscale robotic vehicles. The use of such vehicles for surveillance and detection operations has become increasingly important in defense and humanitarian applications. Through an evolutionary process similar to that found in nature, the genetic programming model generates a computer program that when downloaded onto a robotic vehicle's on-board computer will guide the robot to successfully accomplish its task. Simulations of multiple robots engaged in problem-solving tasks have demonstrated cooperative behaviors. This report also discusses the behavior model produced by genetic programming and presents some results achieved during the study

  1. Evaluation of ball and roller bearings restored by grinding

    Science.gov (United States)

    Parker, R. J.; Zaretsky, E. V.; Chen, S. M.

    1976-01-01

    A joint program was undertaken to restore by grinding those rolling-element bearings which are currently being discarded at aircraft engine and transmission overhaul. Three bearing types were selected from the UH-1 helicopter engine (T-53) and transmission for the pilot program. Groups of each of these bearings were visually and dimensionally inspected for suitability for restoration. A total of 250 bearings were restored by grinding. Of this number, 30 bearings from each type were endurance tested to a TBO of 1600 hours. No bearing failures occurred related to the restoration by grinding process. The two bearing failures which occurred were due to defective rolling elements and were typical of those which may occur in new bearings. The restorable component yield to the three groups was in excess of 90 percent.

  2. Mentorship Programs for Faculty Development in Academic General Pediatric Divisions

    Directory of Open Access Journals (Sweden)

    Jennifer Takagishi

    2011-01-01

    Discussion. General pediatric division chiefs acknowledge the benefits of mentoring relationships, and some have programs in place. Many need tools to create them. Pediatric societies could facilitate this critical area of professional development.

  3. Ohio Uses Wetlands Program Development Grants to Protect Wetlands

    Science.gov (United States)

    The wetland water quality standards require the use of ORAM score to determine wetland quality. OEPA has also used these tools to evaluate wetland mitigation projects, develop performance standards for wetland mitigation banks and In Lieu Fee programs an.

  4. General atomics low speed Maglev technology development program (Supplemental #3)

    Science.gov (United States)

    2005-05-01

    This report details accomplishments of the Low Speed Maglev Technology Development Program, Supplemental #3. The 4 major tasks included: guideway foundation construction, fabrication and installation of 7 guideway modules, system integration and test...

  5. Industrial development - consequences about the implantation of Brazilian Nuclear Program

    International Nuclear Information System (INIS)

    Syllus, C.

    1987-07-01

    The strategy to promote the growing industry participation in the Brazilian Nuclear Program, the difficulties, the measurements adopted for overcoming and the results obtained in terms of industrial development, are presented. (M.C.K.) [pt

  6. The General Atomics low speed urban Maglev technology development program

    Science.gov (United States)

    2003-01-01

    The overall objective of this program is to develop magnetic levitation technology that is a cost effective, reliable, : and environmentally friendly option for urban mass transportation in the United States. Maglev is a revolutionary : approach in w...

  7. 2013 Iowa DOT engineering intern development and management program.

    Science.gov (United States)

    2013-11-01

    The Institute for Transportation (InTrans) at Iowa State University (ISU) developed an internship mentoring program in collaboration : with the Iowa Department of Transportation (DOT) to provide additional mentorship to both student interns and Iowa ...

  8. Developing an interdisciplinary certificate program in transportation planning.

    Science.gov (United States)

    2010-09-01

    This project develops and implements a graduate certificate in transportation planning. Texas A&M : University (A&M) currently offers instruction in transportation through its Master of Urban Planning (MUP) : and Civil Engineering (CE) programs; howe...

  9. Radar Location Equipment Development Program: Phase I

    Energy Technology Data Exchange (ETDEWEB)

    Sandness, G.A.; Davis, K.C.

    1985-06-01

    The work described in this report represents the first phase of a planned three-phase project designed to develop a radar system for monitoring waste canisters stored in a thick layer of bedded salt at the Waste Isolation Pilot Plant near Carlsbad, New Mexico. The canisters will be contained in holes drilled into the floor of the underground waste storage facility. It is hoped that these measurements can be made to accuracies of +-5 cm and +-2/sup 0/, respectively. The initial phase of this project was primarily a feasibility study. Its principal objective was to evaluate the potential effectiveness of the radar method in the planned canister monitoring application. Its scope included an investigation of the characteristics of radar signals backscattered from waste canisters, a test of preliminary data analysis methods, an assessment of the effects of salt and bentonite (a proposed backfill material) on the propagation of the radar signals, and a review of current ground-penetrating radar technology. A laboratory experiment was performed in which radar signals were backscattered from simulated waste canisters. The radar data were recorded by a digital data acquisition system and were subsequently analyzed by three different computer-based methods to extract estimates of canister location and tilt. Each of these methods yielded results that were accurate within a few centimeters in canister location and within 1/sup 0/ in canister tilt. Measurements were also made to determine the signal propagation velocities in salt and bentonite (actually a bentonite/sand mixture) and to estimate the signal attenuation rate in the bentonite. Finally, a product survey and a literature search were made to identify available ground-penetrating radar systems and alternative antenna designs that may be particularly suitable for this unique application. 10 refs., 21 figs., 4 tabs.

  10. Radar Location Equipment Development Program: Phase I

    International Nuclear Information System (INIS)

    Sandness, G.A.; Davis, K.C.

    1985-06-01

    The work described in this report represents the first phase of a planned three-phase project designed to develop a radar system for monitoring waste canisters stored in a thick layer of bedded salt at the Waste Isolation Pilot Plant near Carlsbad, New Mexico. The canisters will be contained in holes drilled into the floor of the underground waste storage facility. It is hoped that these measurements can be made to accuracies of +-5 cm and +-2 0 , respectively. The initial phase of this project was primarily a feasibility study. Its principal objective was to evaluate the potential effectiveness of the radar method in the planned canister monitoring application. Its scope included an investigation of the characteristics of radar signals backscattered from waste canisters, a test of preliminary data analysis methods, an assessment of the effects of salt and bentonite (a proposed backfill material) on the propagation of the radar signals, and a review of current ground-penetrating radar technology. A laboratory experiment was performed in which radar signals were backscattered from simulated waste canisters. The radar data were recorded by a digital data acquisition system and were subsequently analyzed by three different computer-based methods to extract estimates of canister location and tilt. Each of these methods yielded results that were accurate within a few centimeters in canister location and within 1 0 in canister tilt. Measurements were also made to determine the signal propagation velocities in salt and bentonite (actually a bentonite/sand mixture) and to estimate the signal attenuation rate in the bentonite. Finally, a product survey and a literature search were made to identify available ground-penetrating radar systems and alternative antenna designs that may be particularly suitable for this unique application. 10 refs., 21 figs., 4 tabs

  11. Using scenario based programming to develop embedded control software

    NARCIS (Netherlands)

    Bettiol, F.

    2015-01-01

    A new paradigm to develop embedded software is waking up the interest of companies. Its name is Scenario Based Programming and it claims to be a good approach to develop embedded software. Live Sequence Charts (LSC), a visual language supporting the paradigm, enables the developers to specify a

  12. Developing Customized Programs for Steel and Other Heavy Industries.

    Science.gov (United States)

    Day, Philip R., Jr.

    1984-01-01

    Describes Dundalk Community College's (DCC's) customized training programs for local industries. Looks at employment problems and outlook in Baltimore County, the development of a training agreement with Bethlehem Steel, the use of the Developing a Curriculum (DACUM) process to develop skill profiles, and future directions. (DMM)

  13. Developments in the electron gun simulation program, EGUN

    International Nuclear Information System (INIS)

    Herrmannsfeldt, W.B.

    1995-01-01

    This paper discusses the developments in the electron gun simulation programs that are based on EGUN with its derivatives and supporting programs. Much of the code development has been inspired by technology changes in computer hardware; the implications of this evolution on EGN2 are discussed. Some examples and a review of the capabilities of the EGUN family are described. copyright 1995 American Institute of Physics

  14. Evaluating a physician leadership development program - a mixed methods approach.

    Science.gov (United States)

    Throgmorton, Cheryl; Mitchell, Trey; Morley, Tom; Snyder, Marijo

    2016-05-16

    Purpose - With the extent of change in healthcare today, organizations need strong physician leaders. To compensate for the lack of physician leadership education, many organizations are sending physicians to external leadership programs or developing in-house leadership programs targeted specifically to physicians. The purpose of this paper is to outline the evaluation strategy and outcomes of the inaugural year of a Physician Leadership Academy (PLA) developed and implemented at a Michigan-based regional healthcare system. Design/methodology/approach - The authors applied the theoretical framework of Kirkpatrick's four levels of evaluation and used surveys, observations, activity tracking, and interviews to evaluate the program outcomes. The authors applied grounded theory techniques to the interview data. Findings - The program met targeted outcomes across all four levels of evaluation. Interview themes focused on the significance of increasing self-awareness, building relationships, applying new skills, and building confidence. Research limitations/implications - While only one example, this study illustrates the importance of developing the evaluation strategy as part of the program design. Qualitative research methods, often lacking from learning evaluation design, uncover rich themes of impact. The study supports how a PLA program can enhance physician learning, engagement, and relationship building throughout and after the program. Physician leaders' partnership with organization development and learning professionals yield results with impact to individuals, groups, and the organization. Originality/value - Few studies provide an in-depth review of evaluation methods and outcomes of physician leadership development programs. Healthcare organizations seeking to develop similar in-house programs may benefit applying the evaluation strategy outlined in this study.

  15. Unbalance Response Prediction for Rotors on Ball Bearings Using Speed and Load Dependent Nonlinear Bearing Stiffness

    Science.gov (United States)

    Fleming, David P.; Poplawski, J. V.

    2003-01-01

    Rolling-element bearing forces vary nonlinearly with bearing deflection. Thus an accurate rotordynamic analysis requires that bearing forces corresponding to the actual bearing deflection be utilized. For this work bearing forces were calculated by COBRA-AHS, a recently developed rolling-element bearing analysis code. Bearing stiffness was found to be a strong function of bearing deflection, with higher deflection producing markedly higher stiffness. Curves fitted to the bearing data for a range of speeds and loads were supplied to a flexible rotor unbalance response analysis. The rotordynamic analysis showed that vibration response varied nonlinearly with the amount of rotor imbalance. Moreover, the increase in stiffness as critical speeds were approached caused a large increase in rotor and bearing vibration amplitude over part of the speed range compared to the case of constant bearing stiffness. Regions of bistable operation were possible, in which the amplitude at a given speed was much larger during rotor acceleration than during deceleration. A moderate amount of damping will eliminate the bistable region, but this damping is not inherent in ball bearings.

  16. Phylogeography of mitochondrial DNA variation in brown bears and polar bears

    Science.gov (United States)

    Shields, Gerald F.; Adams, Deborah; Garner, Gerald W.; Labelle, Martine; Pietsch, Jacy; Ramsay, Malcolm; Schwartz, Charles; Titus, Kimberly; Williamson, Scott

    2000-01-01

    We analyzed 286 nucleotides of the middle portion of the mitochondrial cytochrome b gene of 61 brown bears from three locations in Alaska and 55 polar bears from Arctic Canada and Arctic Siberia to test our earlier observations of paraphyly between polar bears and brown bears as well as to test the extreme uniqueness of mitochondrial DNA types of brown bears on Admiralty, Baranof, and Chichagof (ABC) islands of southeastern Alaska. We also investigated the phylogeography of brown bears of Alaska's Kenai Peninsula in relation to other Alaskan brown bears because the former are being threatened by increased human development. We predicted that: (1) mtDNA paraphyly between brown bears and polar bears would be upheld, (2) the mtDNA uniqueness of brown bears of the ABC islands would be upheld, and (3) brown bears of the Kenai Peninsula would belong to either clade II or clade III of brown bears of our earlier studies of mtDNA. All of our predictions were upheld through the analysis of these additional samples.

  17. Phylogeography of mitochondrial DNA variation in brown bears and polar bears.

    Science.gov (United States)

    Shields, G F; Adams, D; Garner, G; Labelle, M; Pietsch, J; Ramsay, M; Schwartz, C; Titus, K; Williamson, S

    2000-05-01

    We analyzed 286 nucleotides of the middle portion of the mitochondrial cytochrome b gene of 61 brown bears from three locations in Alaska and 55 polar bears from Arctic Canada and Arctic Siberia to test our earlier observations of paraphyly between polar bears and brown bears as well as to test the extreme uniqueness of mitochondrial DNA types of brown bears on Admiralty, Baranof, and Chichagof (ABC) islands of southeastern Alaska. We also investigated the phylogeography of brown bears of Alaska's Kenai Peninsula in relation to other Alaskan brown bears because the former are being threatened by increased human development. We predicted that: (1) mtDNA paraphyly between brown bears and polar bears would be upheld, (2) the mtDNA uniqueness of brown bears of the ABC islands would be upheld, and (3) brown bears of the Kenai Peninsula would belong to either clade II or clade III of brown bears of our earlier studies of mtDNA. All of our predictions were upheld through the analysis of these additional samples. Copyright 2000 Academic Press.

  18. Using online program development to foster curricular change and innovation.

    Science.gov (United States)

    Gwozdek, Anne E; Springfield, Emily C; Peet, Melissa R; Kerschbaum, Wendy E

    2011-03-01

    Distance education offers an opportunity to catalyze sweeping curricular change. Faculty members of the University of Michigan Dental Hygiene Program spent eighteen months researching best practices, planning outcomes and courses, and implementing an e-learning (online) dental hygiene degree completion program. The result is a collaborative and portfolio-integrated program that focuses on the development of reflective practitioners and leaders in the profession. A team-based, systems-oriented model for production, implementation, and evaluation has been critical to the program's success. The models and best practices on which this program was founded are described. Also provided is a framework of strategies for development, including the utilization of backward course design, which can be used in many areas of professional education.

  19. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium on energy research in its 3rd year (Development of nano-structured materials for ceramic bearing applications); 1999 nendo ceramic bearing yo nano seigyo zairyo no kenkyu kaihatsu seika hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Coprecipitation in a chloride-containing water solution is utilized to deposit zirconia nano-particles on alumina particles for the manufacture of a composite powder and a sintered body. As compared with a conventional CIP (cold isostatic press)-molded compact, a slip-cast compact is improved in flexural strength from 1.1 to 1.36Gpa. A composite powder granulating unit is installed. Although it is known that use of the citric acid as gelatinizer in the coprecipitation process results in a homogenous ZrO{sub 2}-Al{sub 2}O{sub 3} composite powder, yet a method is contrived to achieve high crystallinity without gelatinizer by freezing and drying a chloride-containing water solution in a microgravity field. In the near-net molding of spherical ceramic particles, an error in diameter of not more than 50{mu}m is realized. A mass production technology is established by which an inexpensive general-purpose alumina nano-structured material is die-compacted for the manufacture of low-cost ceramic bearings. A high-speed super-flat spherical surface processing technology is developed. In a 25kg-load fatigue test conducted for a combination of nano-structured ceramic balls and steel flat plates that bear the balls, a 240-hour life is attained. The bearing steel stands comparison with those available on the market. (NEDO)

  20. HV Switch Tube Development Program status report: April 28, 1978

    International Nuclear Information System (INIS)

    Winje, R.A.

    1978-01-01

    The HV Switch Tube Development Program encompassed development contracts to both Eimac (Division of Varian) and RCA. Both companies were required to develop a design for the tube and to build and test two tubes. The development program began in April, 1976. Currently, both companies have built tubes; Eimac has built one and RCA has built two. As initially built, both tubes exhibited unstable operation; however, RCA has implemented design changes which stabilized the tube operation. Eimac has a design modification which they believe will produce stable operation when the change is implemented. Both tubes have been tested to a limited degree and no other abnormal characteristics have been observed

  1. The development and implementation of a dry active waste (DAW) sorting program at Catawba Nuclear Station

    International Nuclear Information System (INIS)

    Schulte, J.H.; McNamara, P.N.

    1988-01-01

    Duke Power Company, like other nuclear utilities, bears a burdensome radwaste disposal cost that has rapidly escalated during recent years. Dry active waste (DAW) represents approximately 85% of the total radioactive waste volume shipped to low-level disposal facilities. Sorting waste with less than detectable radioactivity from waste with detectable radioactivity provides a volume reduction (VR) technique that can save significant radwaste disposal costs and conserve dwindling burial space. This paper presents the development and results of a project that was conducted at Catawba Nuclear Station to determine the volume reduction potential from sorting DAW. Guidelines are given so that other utilities can perform a VR potential study on a low cost basis. Based on the results of the DAW VR study, an overall DAW volume radiation program was initiated at Duke Power Company. This program includes personnel training, drumming techniques, bag tracking and equipment purchases for sorting. This program has been fully implemented at Duke Power Company since January 1, 1988 and preliminary results and savings are given

  2. Program Leadership from a Nordic Perspective - Managing Education Development

    DEFF Research Database (Denmark)

    Högfeldt, Anna-Karin; Cornell, Ann; Cronhjort, Mikael

    2012-01-01

    In this paper we focus on university educational development issues by investigating the program leadership at five Nordic technical universities. Specifically, the paper compares definitions, views and experiences of education leadership in the Nordic Five Tech (N5T) universities. The paper does...... this by, first, reviewing the definitions of roles and responsibilities for program directors at each university, and second, by presenting results from a survey carried out in March 2012 among program directors at the N5T universities. Based on this data, we analyze how program directors experience...... their role, their possibilities to lead, and their opportunities of learning to lead. How is time for reflection and development as leaders handled at the different universities? The paper goes on to consider what impact the mandate of the leadership role has on the possibilities for developing educational...

  3. THE VIEWS OF FOREST OUTSKIRT COMMUNITY ON AGROFORESTRY DEVELOPMENT PROGRAM

    Directory of Open Access Journals (Sweden)

    Dewa Oka Suparwata

    2018-04-01

    Full Text Available Nowadays, development of agroforestry has been focused on the people living near forest. Positive views from community may have a good impact on agroforestry development program. This research aims to study the views of the forest outskrit community on the agroforestry development program in Dulamayo Barat village, Telaga Sub District, Gorontalo Regency, Gorontalo Province. The study used survey approach and focus group discussion (FGD method. Respondents were all the members of agroforestry farmer group. The entire population were taken for interview (10 respondents while FGD was attended by 26 participants. Data were analyzed descriptively. The result showed that 100% of the respondents want the program to be sustainable, although from the socio economic point of view the impact has not contributed significantly. From the respondents views of its benefit, 50% believe that the program is for critical land rehabilitation, 30% have a view for the improvement of environmental service, 10% view to increase community economy, and 10% view that the program is to eliminate erosion. These indicate that the community is concerned with agroforestry development, therefore, continuous facilitation is needed. Furthermore, the community expects to be actively involved in the agroforestry development program.

  4. Ten years of Developing International Volcanology Graduate Study Programs

    Science.gov (United States)

    Rose, W. I.

    2010-12-01

    In 2000 I reported at this symposium about multi-institutional graduate field trips to IAVCEI events, such as the Bali meeting and its importance in building international collegiality and awareness among the volcanology doctoral students. NSF was an enthusiastic supporter of these field sessions and this support has continued through the highly successful Pucon and Reykjavik sessions. International volcanology graduate program development began with several exchange programs. EHaz was a highly successful program (McGill, Simon Fraser, Michigan Tech, Buffalo, UNAM and Universidad de Colima) funded by the Department of Education (FIPSE) that moved students across North America where dozens of graduate students spent semesters of their study abroad and shared annual field trips and online student led graduate seminar classes. Michigan Tech’s volcanology graduate program started a Masters International program that combined Peace Corps service with hazards mitigation graduate study and students were placed by Peace Corps in countries with prominent natural hazards. The new program funded 2 year residences in foreign environments, principally in Pacific Latin America. NSF strongly supported this program from its inception, and eventually it gained NSF PIRE support. Dozens of students have initiated the 3 year program (15 completed) to date. A similar PIRE developed at UAF with a link to volcanology in the Russian Far East. One gain is the development of many socially-conscious research selections. Beginning this year transatlantic dual degree masters programs in volcanology are being offered by a consortium of US and European volcanology programs (Michigan Tech, Buffalo, Clermont Ferrand and University of Milan Bicocca), again aided by FIPSE funding. Students have dual advisors on both sides of the Atlantic and spend about half of their two year programs in Europe and half in US. Faculty also travel in the program and the four campuses are increasingly linked by

  5. Coordinated irradiation plan for the Fuel Refabrication and Development Program

    International Nuclear Information System (INIS)

    Barner, J.O.

    1979-04-01

    The Department of Energy's Fuel Refabrication and Development (FRAD) Program is developing a number of proliferation-resistant fuel systems and forms for alternative use in nuclear reactors. A major portion of the program is the development of irradiation behavioral information for the fuel system/forms with the ultimate objective of qualifying the design for licensing and commercial utilization. The nuclear fuel systems under development include denatured thoria--urania fuels and spiked urania--plutonia or thoria--plutonia fuels. The fuel forms being considered include pellet fuel produced from mechanically mixed or coprecipitated feed materials, pellet fuel fabricated from partially calcined gel-derived or freeze-dried spheres (hybrid fuel) and packed-particle fuel produced from sintered gel-derived spheres (sphere-pac). This document describes the coordinated development program that will be used to test and demonstrate the irradiation performance of alternative fuels

  6. Graphical programming interface: A development environment for MRI methods.

    Science.gov (United States)

    Zwart, Nicholas R; Pipe, James G

    2015-11-01

    To introduce a multiplatform, Python language-based, development environment called graphical programming interface for prototyping MRI techniques. The interface allows developers to interact with their scientific algorithm prototypes visually in an event-driven environment making tasks such as parameterization, algorithm testing, data manipulation, and visualization an integrated part of the work-flow. Algorithm developers extend the built-in functionality through simple code interfaces designed to facilitate rapid implementation. This article shows several examples of algorithms developed in graphical programming interface including the non-Cartesian MR reconstruction algorithms for PROPELLER and spiral as well as spin simulation and trajectory visualization of a FLORET example. The graphical programming interface framework is shown to be a versatile prototyping environment for developing numeric algorithms used in the latest MR techniques. © 2014 Wiley Periodicals, Inc.

  7. The DOE safeguards and security technology development program

    International Nuclear Information System (INIS)

    Cherry, R.C.; Wheelock, A.J.

    1991-01-01

    This paper reports that strategic planning for safeguards and security within the Department of Energy emphasizes the contributions of advanced technologies to the achievement of Departmental protection program goals. The Safeguards and Security Technology Development Program provides state-of-the-art technologies, systems and technical services in support of the policies and programmatic requirements for the protection of Departmental assets. The Program encompasses research and development in physical security, nuclear material control and accountability, information security and personnel security, and the integration of these disciplines in advanced applications. Technology development tasks serve goals that range from the maintenance of an effective technology base to the development, testing and evaluation of applications to meet field needs. A variety of factors, from the evolving threat to reconfiguration of the DOE complex and the technical requirements of new facilities, are expected to influence safeguards and security technology requirements and development efforts. Implementation of the Program is based on the systematic identification, prioritization and alignment of technology development tasks and needs. Initiatives currently underway are aimed at enhancing technology development project management. Increased management attention is also being placed on efforts to promote the benefits of the Program through technology transfer and interagency liaison

  8. ESTIMATING FINANCIAL SUPPORT OF REGIONAL PROGRAMS OF SOCIAL ECONOMIC DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Iryna Kokhan

    2016-03-01

    Full Text Available The given article presents the analysis of the experience of the financial support of the regional programs of social economic development and the areas of usage of internal and external resources of the area. Dynamic and balanced development of regions is one of the most important issues for further establishment of marketing relations and social transformations in Ukraine. The Aim lies in the evaluation of financial support of the approved regional programs and launching the amount of their financing. The assessment of social economic situation in Ivano-Frankivsk region in terms of nationwide tendencies allows asserting that economic growth depends on the amounts and sources provided by the state. To determine close connection between  the amount of financing  for the programs  and  gross domestic product, the coefficient of correlation was calculated according to Pierson. It was proved that the amount of financing regional programs of social economic development influences the growth rate of gross domestic product. During research period the activation of regional authority institutions is being surveyed regarding the adoption and financing target regional programs. It was determined that the dynamic activity of the regional community and its territorial units on realization in terms of defined strategic priorities for programs of social economic development will facilitate disproportion reduction and differences in the development of territory units in the region, as well as positively influences the growth of gross domestic product providing steady increase of social welfare. Keywords: social economic regional development, ecology programs, social programs, gross regional domestic product, Pierson’s correlation coefficient. JEL: R 58

  9. Resilient and Corrosion-proof Rolling Element Bearings Made from Ni-ti Alloys for Aerospace Mechanism Applications and the Ultimate Space Technology Development Platform

    Science.gov (United States)

    Dellacorte, Christopher

    2014-01-01

    The International Space Station provides a unique microgravity laboratory environment for research. The ISS also serves as an effective platform for the development of technologies and engineered solutions related to living and working in space. The space environment also challenges our capabilities related to lubrication and tribology. In this seminar, Dr. DellaCorte will review the basics of space mechanism tribology and the challenges of providing good lubrication and long-life in the harsh space environment. He will also discuss recent tribological challenges associated with the Solar Alpha Rotary Joint (SARJ) bearings and life support hardware that must operate under severe conditions that are literally out of this world. Each tribology challenge is unique and their solutions often result in new technologies that benefit the tribology community everywhere, even back on Earth

  10. Increasing adolescent mothers' knowledge of child development: an intervention program.

    Science.gov (United States)

    Fulton, A M; Murphy, K R; Anderson, S L

    1991-01-01

    This study focused upon an intervention program that allowed adolescent mothers to have major input in identifying knowledge they needed concerning their children's growth and their own parenting skills. Seventy-six females participated in the 4-month program. A pretest-posttest design was used to measure changes in self-esteem, knowledge of child development, and tendencies toward inappropriate interactions with children. Analysis of effectiveness of this program indicated that it had been effective. Results revealed significant differences between pre- and posttest measures of child development knowledge in the areas of infant and toddler development. Further analysis indicated a significant change in the subjects' child abuse potential at the end of the program. No significant difference could be found in measures of self-esteem between the beginning and end of the program. A 10-month follow-up study coordinated between two public agencies found that none of the adolescent parents who had completed the program had been reported for child abuse or neglect. The results support the importance of short-term intervention programs for adolescent parents.

  11. Canadian CANDU fuel development program and recent fuel operating experience

    International Nuclear Information System (INIS)

    Lau, J.H.K.; Inch, W.W.R.; Cox, D.S.; Steed, R.G.; Kohn, E.; Macici, N.N.

    1999-01-01

    This paper reviews the performance of the CANDU fuel in the Canadian CANDU reactors in 1997 and 1998. The operating experience demonstrates that the CANDU fuel has performed very well. Over the 2-year period, the fuel-bundle defect rate for all bundles irradiated in the Canadian CANDU reactors has remained very low, at between 0.006% to 0.016%. On a fuel element basis, this represents an element defect rate of less than about 0.0005%. One of the reasons for the good fuel performance is the support provided by the Canadian fuel research and development programs. These programs address operational issues and provide evolutionary improvements to the fuel products. The programs consist of the Fuel Technology Program, funded by the CANDU Owners Group, and the Advanced Fuel and Fuel Cycles Technology Program, funded by Atomic Energy of Canada Ltd. These 2 programs, which have been in place for many years, complement each other by sharing expert resources and experimental facilities. This paper describes the programs in 1999/2000, to provide an overview of the scope of the programs and the issues that these programs address. (author)

  12. Developing an online certification program for nutrition education assistants.

    Science.gov (United States)

    Christofferson, Debra; Christensen, Nedra; LeBlanc, Heidi; Bunch, Megan

    2012-01-01

    To develop an online certification program for nutrition education paraprofessionals to increase knowledge and confidence and to overcome training barriers of programming time and travel expenses. An online interactive certification course based on Supplemental Nutrition Assistance Program-Education and Expanded Food and Nutrition Education Program core competencies was delivered to employees of both programs. Traditional vs online training was compared. Course content validity was determined through expert review by registered dietitians. Parameters studied included increase of nutrition knowledge and teaching technique/ability, educator satisfaction, and programming costs related to training. Utah State University Extension. Twenty-two Supplemental Nutrition Assistance Program-Education and Expanded Food and Nutrition Education Program educators in Utah. Knowledge and skills were measured using pre/posttest statistics. Participant satisfaction was measured with a survey. Paired t test; satisfaction survey. The change in paraprofessional knowledge score was statistically significant (P educators because of the training. An estimated $16,000 was saved by providing the training online as compared to a face-to-face training. This interactive online program is a cost-effective way to increase paraprofessional knowledge and job satisfaction. Copyright © 2012 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

  13. Mentorship programs for faculty development in academic general pediatric divisions.

    Science.gov (United States)

    Takagishi, Jennifer; Dabrow, Sharon

    2011-01-01

    Introduction. Mentoring relationships have been shown to support academicians in areas of research, work/life balance, and promotion. Methods. General pediatric division chiefs accessed an electronic survey asking about mentorship relationships, their ability to create a mentorship program, and resources needed. Results. Dyadic mentorship programs were available at 53% of divisions. Peer mentorship programs were available at 27% of divisions. Overall, 84% of chiefs believed that dyadic mentorship would benefit their faculty. 91% of chiefs believed that peer mentorship would benefit their faculty. Chiefs were interested in starting peer (57%) or dyadic (55%) mentorship programs. Few divisions had a peer mentorship program available, whereas 24% already had a dyadic program. 43% of chiefs felt that they had the tools to start a program. Many tools are needed to create a program. Discussion. General pediatric division chiefs acknowledge the benefits of mentoring relationships, and some have programs in place. Many need tools to create them. Pediatric societies could facilitate this critical area of professional development.

  14. Idaho Chemical Processing Plant Spent Fuel and Waste Management Technology Development Program Plan

    International Nuclear Information System (INIS)

    1993-09-01

    The Department of Energy (DOE) has received spent nuclear fuel (SNF) at the Idaho Chemical Processing Plant (ICPP) for interim storage and reprocessing since 1953. Reprocessing of SNF has resulted in an existing inventory of 1.5 million gallons of radioactive sodium-bearing liquid waste and 3800 cubic meters (m 3 ) of calcine, in addition to the 768 metric tons (MT) of SNF and various other fuel materials in inventory. To date, the major activity of the ICPP has been the reprocessing of SNF to recover fissile uranium; however, recent changes in world events have diminished the demand to recover and recycle this material. As a result, DOE has discontinued reprocessing SNF for uranium recovery, making the need to properly manage and dispose of these and future materials a high priority. In accordance with the Nuclear Waste Policy Act (NWPA) of 1982, as amended, disposal of SNF and high-level waste (HLW) is planned for a geological repository. Preparation of SNF, HLW, and other radioactive wastes for disposal may include mechanical, physical, and/or chemical processes. This plan outlines the program strategy of the ICPP Spent Fuel and Waste Management Technology Development Program (SF ampersand WMTDP) to develop and demonstrate the technology required to ensure that SNF and radioactive waste will properly stored and prepared for final disposal. Program elements in support of acceptable interim storage and waste minimization include: developing and implementing improved radioactive waste treatment technologies; identifying and implementing enhanced decontamination and decommissioning techniques; developing radioactive scrap metal (RSM) recycle capabilities; and developing and implementing improved technologies for the interim storage of SNF

  15. Re-Imagining Program Development and Re-Engineering Program Design.

    Science.gov (United States)

    Currie, Geoffrey M; Thomas, Catherine J

    2018-05-03

    Program development and review is a central part of institutional and industry quality assurance. Traditional approaches, while well established, present a number of barriers that could undermine process integrity and quality outcomes. Here a new approach to program development and design is explored with the goal of enhancing outcomes for students and institutions. Copyright © 2018 by the Society of Nuclear Medicine and Molecular Imaging, Inc.

  16. Leadership development programs for physicians: a systematic review.

    Science.gov (United States)

    Frich, Jan C; Brewster, Amanda L; Cherlin, Emily J; Bradley, Elizabeth H

    2015-05-01

    Physician leadership development programs typically aim to strengthen physicians' leadership competencies and improve organizational performance. We conducted a systematic review of medical literature on physician leadership development programs in order to characterize the setting, educational content, teaching methods, and learning outcomes achieved. Articles were identified through a search in Ovid MEDLINE from 1950 through November 2013. We included articles that described programs designed to expose physicians to leadership concepts, outlined teaching methods, and reported evaluation outcomes. A thematic analysis was conducted using a structured data entry form with categories for setting/target group, educational content, format, type of evaluation and outcomes. We identified 45 studies that met eligibility criteria, of which 35 reported on programs exclusively targeting physicians. The majority of programs focused on skills training and technical and conceptual knowledge, while fewer programs focused on personal growth and awareness. Half of the studies used pre/post intervention designs, and four studies used a comparison group. Positive outcomes were reported in all studies, although the majority of studies relied on learner satisfaction scores and self-assessed knowledge or behavioral change. Only six studies documented favorable organizational outcomes, such as improvement in quality indicators for disease management. The leadership programs examined in these studies were characterized by the use of multiple learning methods, including lectures, seminars, group work, and action learning projects in multidisciplinary teams. Physician leadership development programs are associated with increased self-assessed knowledge and expertise; however, few studies have examined outcomes at a system level. Our synthesis of the literature suggests important gaps, including a lack of programs that integrate non-physician and physician professionals, limited use of more

  17. Superconductor bearings, flywheels and transportation

    International Nuclear Information System (INIS)

    Werfel, F N; Floegel-Delor, U; Rothfeld, R; Riedel, T; Goebel, B; Wippich, D; Schirrmeister, P

    2012-01-01

    This paper describes the present status of high temperature superconductors (HTS) and of bulk superconducting magnet devices, their use in bearings, in flywheel energy storage systems (FESS) and linear transport magnetic levitation (Maglev) systems. We report and review the concepts of multi-seeded REBCO bulk superconductor fabrication. The multi-grain bulks increase the averaged trapped magnetic flux density up to 40% compared to single-grain assembly in large-scale applications. HTS magnetic bearings with permanent magnet (PM) excitation were studied and scaled up to maximum forces of 10 kN axially and 4.5 kN radially. We examine the technology of the high-gradient magnetic bearing concept and verify it experimentally. A large HTS bearing is tested for stabilizing a 600 kg rotor of a 5 kWh/250 kW flywheel system. The flywheel rotor tests show the requirement for additional damping. Our compact flywheel system is compared with similar HTS–FESS projects. A small-scale compact YBCO bearing with in situ Stirling cryocooler is constructed and investigated for mobile applications. Next we show a successfully developed modular linear Maglev system for magnetic train operation. Each module levitates 0.25t at 10 mm distance during one-day operation without refilling LN 2 . More than 30 vacuum cryostats containing multi-seeded YBCO blocks are fabricated and are tested now in Germany, China and Brazil.

  18. Faculty Development Effectiveness: Insights from a Program Evaluation

    Directory of Open Access Journals (Sweden)

    Anupma Wadhwa

    2014-01-01

    Full Text Available Background. Faculty development programs are often time and resource intensive. In order to accommodate time constrained clinicians a limited time commitment faculty development program was developed and was shown to be effective in improving participant’s scholarly productivity. Objectives. The objective of this study was to assess participants’ perceptions of why the faculty development program was effective in promoting scholarship in education. Methods. In-depth semistructured interviews of course participants were conducted a year after completing a faculty development program. The interviews were audiotaped and transcribed verbatim. The transcriptions were coded independently by the investigators for dominant themes. The investigators held coding meetings to further refine the themes and discrepancies were handled by referring to the transcripts and reaching consensus. Results. The participants’ satisfaction with the course as described in the interviews correlated with the early satisfaction surveys. Reasons offered for this impact fell into four broad categories: course content, course format, social networking during the course, and the course facilitation coaching strategies to achieve goals. Conclusions. Course focusing on the process, experiential learning, and situating the course facilitator in the role of a functional mentor or coach to complete projects can be effective in facilitating behaviour change after faculty development programs.

  19. The development of a fear of falling interdisciplinary intervention program

    Directory of Open Access Journals (Sweden)

    Fernando Gomez

    2008-01-01

    Full Text Available Fernando Gomez, Carmen-Lucia CurcioResearch Group on Gerontology and Geriatrics, Health Sciences Faculty, University of Caldas, Manizales, ColombiaObjective: To describe the development process of a protocol for a fear of falling interdisciplinary intervention program based on the main factors associated with fear of falling.Design/methods: The process of developing a protocol consisted of defining the target population, selecting the initial assessment components, adapting the intervention program based on findings about fear of falling and restriction of activities in this population.Settings: University-affiliated outpatient vertigo, dizziness and falls clinic in coffee-growers zone of Colombian Andes Mountains.Results: An intervention program was developed based on three main falling conceptual models. A medical intervention, based on a biomedical and pathophysiological model, a physiotherapeutic intervention based on a postural control model and a psychological intervention based on a biological-behavioral model.Conclusion: This interdisciplinary fear of falling intervention program developed is based on particular characteristics of target population, with differences in the inclusion criteria and the program intervention components; with emphasis on medical (recurrent falls and dizziness evaluation and management, psychological (cognitive-behavioral therapy and physiotherapeutic (balance and transfers training components.Keywords: fear of falling, elderly programs, Colombian, intervention

  20. Collider Dipole Magnet test program from development through production

    International Nuclear Information System (INIS)

    Bailey, R.E.

    1991-01-01

    Verification of CDM performance, reliability, and magnet production processes will be accomplished during the development phase of the program. Key features of this program include thorough in process testing of magnet subassemblies, verification of the magnetic field quality, and demonstration of the CDM performance during the formal qualification program. Reliability demonstration of the CDM design includes component tests and an accelerated life test program. Prototype magnet phase will address achievement of magnet performance goals through a program of fabrications, test, analysis, redesign as required and procurement of modified parts for a second fabrication run. This process would be repeated again if necessary, and would conclude with a final design for the production magnets. Production process validation will address the effects that key production processes have upon magnet performance, using the magnets produced during the Preproduction phase