WorldWideScience

Sample records for based crate controller

  1. Determination of piglet location in farrowing crates based on depth and digital images

    Science.gov (United States)

    Understanding and properly managing behavioral responses of prewean piglets to the farrowing environment can improve well-being and pre-weaning performance of the piglets. This paper aims to quantify piglet location in the farrowing crate as affected by the lactating sow’s lying posture. Each farrow...

  2. New chemical approach to obtain dense layer phosphate-based ionic conductor coating on negative electrode material surface: Synthesis way, outgassing and improvement of C-rate capability

    Science.gov (United States)

    Fleutot, Benoit; Davoisne, Carine; Gachot, Grégory; Cavalaglio, Sébastien; Grugeon, Sylvie; Viallet, Virginie

    2017-04-01

    Li4Ti5O12 (LTO) based batteries have severe gassing behavior during charge/discharge and storage process, due to interfacial reactions between active material and electrolyte solution. In the same time, the electronic and ionic conductivity of pristine LTO is very poor and induces the use of nanoparticles which increase the outgassing phenomena. The coating of LTO particles could be a solution. For this the LTO spinel particles are modified with ionic conductor Li3PO4 coating using a spray-drying method. For the first time a homogeneous thin dense layer phosphate based conductor is obtained without nanoparticles, as a thin film material. It is so possible to study the influence of ionic conductor deposited on the negative electrode material on performances by the controlled layer thickness. This coating was characterized by XRD, SEM, XPS and TEM. The electrochemical performance of Li3PO4 coated Li4Ti5O12 is improved at high C-rate by the surface modification (improvement of 30 mAh g-1 at 5 C-rate compared to pristine LTO for 5 nm of coating), inducing by a modification of surface energy. An optimum coating thickness was studied. This type of coating allows a significant decrease of outgassing phenomena due the conformal coating and opens the way to a great number of studies and new technologies.

  3. Implementation of the ROD Crate DAQ Software for the ATLAS Tile Calorimeter and a Search for a MSSM Higgs Boson decaying into Tau pairs

    CERN Document Server

    Solans Sánchez, Carlos Antonio; Higón Rodríguez, Emilio

    2010-01-01

    The ATLAS experiment of the LHC at CERN started its operation in 2009. The ROD Crate DAQ as a part of the Trigger and Data Acquisition system is responsible for the operation of the sub-detector specific hardware at the level of the back-end electronics crates. In particular, it is the framework that controls the Read-Out Driver of the ATLAS Tile Calorimeter which is responsible for the cell energy and time computation based on the Optimal Filtering algorithm. We describe the implementation of the ROD Crate DAQ for the ATLAS Tile Calorimeter. In first place how the specific Tile hardware and software is described in the configuration database. In second place, the characterization of the various plug-ins for the ROD Crate DAQ, specially the ones for the ROD and TBM motherboards. Results from the transition times of the ROD Crate DAQ measured in real data taking scenario during the year 2010 are presented. In the third place, we present the results from the Optimal Filtering validation in terms of energy resol...

  4. Issues Related to Implementation of the EU Requirements on Plastic Crates and Pallets Containing Heavy Metals in Lithuania

    Directory of Open Access Journals (Sweden)

    Alis Lebedys

    2015-10-01

    Full Text Available The paper presents an analysis of problems which had to be dealt with by Lithuanian institutions while implementing environmental requirements laid down in Article 11 of European Parliament and Council Directive 94/62/EC on Packaging and Packaging Waste as well as in Decision 2009/292/EC of the European Commission establishing the conditions for derogation of plastic crates and plastic pallets related to heavy metal concentration limits set by Directive 94/62/EC. While the Directive puts ban on the usage of packaging with the aggregate concentration of 4 heavy metals (lead, cadmium, mercury and hexavalent chromium exceeding 100 ppm, Decision 2009/292/EC, instead, allows their usage if terms of derogation specified in the Decision are met. The implementation of the Decision means that each crate and/or pallet item circulating in the market with the concentration of the 4 heavy metals above the set level has to be identified, accounted, traced while in service, must at the end of service be delivered into a controlled recycling system and finally recycled in a way specified by the Decision. Therefore, the establishment of such a country-wide system presents a challenging task for the country as EU legislation sets no common requirements for its structure and leaves it to the country’s discretion. This paper systematises and summarises some principles and practices of managing the usage of plastic crates and plastic pallets containing the amount of heavy metals higher than 100 ppm (as set by Directive 94/62/EC in the EU Member States. The paper analyses possibilities and offers several scenarios for implementation of Directive 94/62/EC with respect to plastic crates and pallets with high concentration of heavy metals in Lithuania. Both the Directive and the Decision are based on using the data available from bookkeeping conducted by owners of crates and pallets and the EU environmental accounting/control system used in the country. The offered

  5. Corrosion of Wires on Wooden Wire-Bound Packaging Crates

    Science.gov (United States)

    Samuel L. Zelinka; Stan Lebow

    2015-01-01

    Wire-bound packaging crates are used by the US Army to transport materials. Because these crates may be exposed to harsh environments, they are dip-treated with a wood preservative (biocide treatment). For many years, zinc-naphthenate was the most commonly used preservative for these packaging crates and few corrosion problems with the wires were observed. Recently,...

  6. Platão sob o signo de Sócrates: um novo modelo de paideía

    OpenAIRE

    Eduardo Pereira Batista

    2014-01-01

    A atividade de Sócrates é fundamental para a invenção da filosofia platônica. Embora Sócrates nada tenha escrito, Platão compôs sua obra com base nesta figura que, em seus diálogos, era bem conhecida em Atenas por seu modo habitual de conversar com todos em locais públicos e privados. Na Apologia de Sócrates, Platão delimita esta atividade por meio da qual Sócrates, sob o desígnio do deus de Delfos, passa a examinar seus interlocutores em favor da cidade e da alma. Neste sentido, considerando...

  7. CRATES E O CUIDADO DE SI OU A TERAPÊUTICA DA ALMA

    Directory of Open Access Journals (Sweden)

    Raimundo Araújo dos Santos

    2008-03-01

    Full Text Available Esse artigo pretende ser uma abordagem simples, na verdade, um resumo, recolhido dostextos de Platão sobre o auto-conhecimento e o cuidado de si. Esses são os elementos queconstituem a base do saber ético iniciado por Sócrates e o ponto de partida do que chamamosterapêutica da alma.

  8. Scientific Opinion on the safety evaluation of the process “INTERSEROH Step 2” used to recycle polypropylene crates for use as food contact material

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF

    2013-07-01

    Full Text Available This scientific opinion of the EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the recycling process “INTERSEROH Step 2”, EU register number RECYC070. The process recycles pre-washed damaged food contact re-usable polypropylene crates (RPC or parts of crates which have been used in a closed and controlled product loop into new recycled crates. Through this process, pre-washed damaged RPC and parts of crates are ground into flakes. The flakes are compounded, extruded into pellets then used up to 100 % for the production of new recycled PP crates by injection moulding. The Panel considered that repeated grinding and injection moulding of PP crates which is part of the recycling process, under conditions described by the applicant, is not of safety concern. The Panel concluded that the input of the process “INTERSEROH Step 2” originates from a product loop which is in a closed and controlled chain designed to ensure that only materials and articles which have been intended for food contact are used and that any contamination can be ruled out when run under the conditions described by the applicant. The recycling process “INTERSEROH Step 2” is therefore able to produce recycled PP suitable for manufacturing PP crates intended to be used in contact with whole fruits and vegetables at room temperature or below.

  9. Use of Insulated Covers over Product Crates to Reduce Losses in Amaranth during Shipping Delays

    Directory of Open Access Journals (Sweden)

    Lizanne Wheeler

    2015-12-01

    Full Text Available Amaranth is a leafy vegetable with high nutrient content which is sensitive to temperature and low relative humidity. Delays in shipment to market may result in significant losses, therefore improved packaging to minimize mechanical damage and reduce moisture loss are desirable. Amaranth was stored in three types of consumer packages, bunches, clamshells and thin plastic bags, within vented plastic crates. Pallet loads were either covered with insulated material or not, while awaiting transportation. Results indicated covering pallets improved the color and overall quality while reducing weight loss and wilting. Covered crates had a “good” (7.6/9.0 overall quality while uncovered averaged 5.5/9.0 or “moderate” quality. There were significant differences in consumer package type, with the bagged amaranth having almost “excellent” quality (8.8/9.0 compared to “good-fair” quality in clamshells (6.2/9.0 and “poor-fair” quality in the control bunches (4.7/9.0. Amaranth stored in thin plastic bags was better in quality and color, with less weight loss and wilting, however, temperatures at the end of six hours of storage were higher and this may lead to microbial growth. Storage of amaranth in thin bags or clamshell packages, within plastic crates covered with insulated pallet covers while awaiting shipping resulted in improved overall quality and color.

  10. Hipócrates y la medicina mono-discursiva.

    OpenAIRE

    Julio Eduardo Hoyos

    1998-01-01

    Utilizando el método propuesto por Freud, en su análisis del surgimiento de la religión judaica, a partir de Moisés, se pretende hacer un análisis de las condiciones en que surge la medicina Hipocrática y de cómo Hipócrates puede ser considerado el padre de la medicina más allá del mito.

  11. Hipócrates y la medicina mono-discursiva.

    Directory of Open Access Journals (Sweden)

    Julio Eduardo Hoyos

    1998-06-01

    Full Text Available Utilizando el método propuesto por Freud, en su análisis del surgimiento de la religión judaica, a partir de Moisés, se pretende hacer un análisis de las condiciones en que surge la medicina Hipocrática y de cómo Hipócrates puede ser considerado el padre de la medicina más allá del mito.

  12. LAS PASIONES DE SÓCRATES THE PASSIONS OF SOCRATES

    Directory of Open Access Journals (Sweden)

    David Morales Troncoso

    2011-03-01

    Full Text Available Este artículo sobre antropología, ética e historia de la filosofía, propone de modo sistemático relacionar aspectos fundamentales de la filosofía del Sócrates Platónico, a saber, su propuesta ética y la experiencia del eros. Para tal efecto se toma como punto inicial un texto del Gorgias platónico, donde Sócrates admite dos grandes pasiones: la filosofía y su amor por Alcibíades. La indagación conducirá, primeramente, a revisar la piedad cívica de Sócrates, entendida como un racionalismo religioso, y que toma la forma de una práctica especial de justicia. En segundo lugar se mostrará que su afán por emular a la justicia divina contrasta con las impiedades de su amigo Alcibíades, exponiendo resultados paradojales en relación al magisterio de Sócrates, lo que genera problemas sobre la efectividad de sus ideas teológicas y su filosofía ética.This article on anthropology, ethics and the history of philosophy, proposes from various disciplines the relation between fundamental aspects of the philosophy of the Platonic Socrates, such as the ethics and the erotic experience. Thus it takes, as a starting point, a text from the platonic Gorgias , where Socrates admits his two great passions, philosophy and his love to Alcibiades. The inquire proceeds, in the first place, to consider the civic piety of Socrates, namely his theological rationalism, that takes the form of a special practice of justice. In second place, it will show that, ironically, his effort to imitate the divine justice will contrast with the impiety of his friend Alcibiades, having paradoxical results in relation to the teachings of Socrates. This situation will generate new problems about the effectiveness of his theological ideas, ethical proposals and philosophical views.

  13. Waste Crate and Container Imaging Using the Vehicle and Cargo Inspection System. Innovative Technology Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    None

    2000-07-01

    The Vehicle and Cargo Inspection System (VACIS) is a highly penetrating gamma ray imaging system that provides a means to non-invasively image crate contents prior to crate disassembly. The VACIS unit uses a 1.6 Curie collimated source (Cesium-137) aimed at a linear detector to create an image as the unit passes by the crate. In the demonstrated mobile unit, the source and detector were mounted on a boom truck. As the crate passed between the source and detector, a near real-time composite image of the contents was constructed from the linear image of the VACIS unit's on board computer and recorded on disk.

  14. Nest building and posture changes and activity budget of gilts housed in pens and crates

    DEFF Research Database (Denmark)

    Andersen, Inger Lise; Vasdal, Guro; Pedersen, Lene Juul

    2014-01-01

    was born until 8 h after the birth of the first piglet. There was no significant effect of the sows breeding value on any of the sow behaviours. Sows housed in pens spent significantly more time nest building than crated sows from 4 to 12 h prepartum (P ... for the lack of space in the crate compared to the pens. Sows in pens spent more time nest building from 4 to 12 h post partum compared to crated sows, and crated sows showed more behaviours related to frustration and restlessness....

  15. High environmental temperature around farrowing induced heat stress in crated sows.

    Science.gov (United States)

    Muns, R; Malmkvist, J; Larsen, M L V; Sørensen, D; Pedersen, L J

    2016-01-01

    The aim of the experiment was to study the impact of high ambient temperature (25°C) around farrowing on crated sows unable to perform thermoregulatory behavior. Twenty sows were housed in 2 farrowing rooms in conventional farrowing crates. In 1 room (CONTROL) temperature was kept at 20°C. In the other room (HEAT) temperature was initially kept at 20°C and gradually raised until it reached 25°C from d 112 to 115 of gestation. Then the temperature was gradually lowered to 20°C. Sows were continuously video recorded for behavior recording. Sows' respiration rates were recorded from d 3 before farrowing to d 5 after farrowing. Sows' rectal temperatures were recorded from d 1 before farrowing to d 8 after farrowing, and sows' udder surface temperatures were recorded from the day of farrowing to d 3 after farrowing. All measures were recorded daily. Sows' BW were recorded at d 108 of gestation and at weaning. Sows' back fat was recorded on farrowing day, when room temperature was set again at 20°C, and at weaning. Piglets were weighed at d 1, 14, and 21. The HEAT sows spent a higher proportion of time lying in the lateral position than CONTROL sows, both during the 16 h before farrowing and the 24 h after the start of farrowing ( 0.10). The HEAT sows had higher rectal temperature on d 1 after farrowing ( sows during the recording period ( sows also tended to have longer farrowing duration ( sows on d 1 before farrowing and on the day of farrowing. On d 7, 8, and 9, CONTROL sows had higher feed intake ( sows were heavier at d 21 after farrowing ( sows' postural behavior. Sows reacted to the thermal challenge with higher respiration rate around farrowing, but both their rectal and udder temperatures were elevated, indicating that they were not able to compensate for the higher ambient temperature. High ambient temperature negatively influenced sows' feed intake, with negative impact on piglets' weaning weight. High temperatures around farrowing (25°C) compromise

  16. Scientific Opinion on the safety evaluation of the process “Schoeller Arca Systems”, used to recycle polypropylene and high-density polyethylene crates for use as food contact material

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF

    2013-04-01

    Full Text Available This scientific opinion of the EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the recycling process “Schoeller Arca Systems”, EC register number RECYC075. The process recycles damaged food contact re-usable polypropylene (PP and high-density polyethylene (HDPE crates which have been used in a closed and controlled product loop into new recycled crates. Through this process, damaged crates are firstly ground into flakes which are further blended with virgin PP or HDPE or used at 100 % to manufacture new recycled PP and HDPE crates. The CEF Panel concluded that the input of the process “Schoeller Arca Systems” originates from a product loop which is in a closed and controlled chain ensuring that only materials and articles which have been intended for food contact are used and that any contamination can be ruled out when run under the conditions described by the applicant. The Panel considered that the repeated grinding and injection moulding of PP and HDPE crates, which is part of the recycling process, under conditions described by the applicant, is not of safety concern. Therefore the recycling process “Schoeller Arca Systems” is able to produce recycled PP and HDPE suitable for manufacturing crates intended to be used in contact at room temperature or below with meat, whole fruits and vegetables as requested by the applicant.

  17. Initial operation and current status of the Fermilab DZero VMEbus-based hardware control and monitor system

    Energy Technology Data Exchange (ETDEWEB)

    Goodwin, R.; Florian, R.; Johnson, M.; Jones, A.; Shea, M.

    1989-11-01

    DZero is a large colliding beams detector at Fermilab. The control system for this detector includes twenty-five VMEbus-based 68020 computers interconnected using the IEEE-802.5 Token Ring local area network. In operation, the system will monitor about fifteen thousand analog channels and several thousand digital status bits, interfaced to the 68020 computers by the MIL-1553 multiplexed data bus. In addition, the VMEbus control system uses a memory-mapped multi-VMEbus interconnect to download parameters to more than one hundred VMEbus data crates in the experiment. Remote host computers can then read and set memory in the detector crates over the network by accessing memory in the control crates. This is an extremely useful feature during the construction phase, because low level diagnostics and testing of all the detector electronics can be done over the Token Ring network using either IBM-PC compatible computers or the laboratory-wide VAX system. The VMEbus control system hardware is now being installed in the DZero movable counting house. Installation is expected to be complete later this year. 4 refs., 2 figs.

  18. Neonatal piglet traits of importance for survival in crates and indoor pens.

    Science.gov (United States)

    Pedersen, L J; Berg, P; Jørgensen, G; Andersen, I L

    2011-04-01

    The primary aim of the present study was to investigate whether the same piglet traits contributed to the same causes of neonatal piglet mortality in crates (CT) and pens (PN). Gilts originating from 2 distinct genetic groups that differed in breeding value for piglet survival rate at d 5 (SR5) were used. These were distributed to farrow in either PN or CT as follows: high-SR5 and CT (n = 30); low-SR5 and CT (n = 27); high-SR5 and PN (n = 22); and low-SR5 and PN (n = 24). Data on individual piglets were collected at birth, including interbirth interval; birth order; birth weight; rectal temperature at birth, 2 h after birth, and 24 h after birth; cordal plasma lactate; and latency to first suckle. Based on autopsy, causes of mortality were divided into stillborn, bitten to death, starvation, crushed, disease, and other causes. Potential risk factors of dying were estimated using a GLM with a logit link function. No significant effect (NS) of housing was observed on the odds of a piglet being stillborn (F(1,73) = 0.1, NS), being crushed (F(1,53) = 1.4, NS), or dying of starvation (F(1,53) = 0.3, NS). No significant differences were observed between the 2 genetic groups for any category of mortality. Piglet traits for pre- and postnatal survival were the same for CT and PN. The odds of being stillborn were increased in piglets born late in the birth order (F(1,1061) = 33.5, P piglets, the greater were the odds of being crushed (F(1,1050) = 18, P piglets. The results emphasize that the microclimate in the PN for newborn piglets and its heat-preserving properties are more important for survival than whether the sow is crated or penned.

  19. Verdad y muerte: Sócrates y Calicles en pugna

    Directory of Open Access Journals (Sweden)

    Pablo Oyarzún R.

    2002-09-01

    Full Text Available Parte de un libro inédito, este ensayo examina el episodio más álgido del diálogo "Gorgias", de Platón, la confrontación de Sócrates y Calicles. Se supone aquí que este diálogo es un momento fundacional de la filosofía platónica, la cual es estimada, a su vez, como matriz del proyecto de la filosofía en su constitución metafísica. Tal constitución, se propone, es concebida en el "Gorgias" como una trama de relaciones de saber y poder determinadas a partir de una reflexión radical sobre la muerte como fundamento de la vida y la verdad. El análisis del episodio en cuestión intenta dar verosimilitud a estahipótesis. (This works examines the most crucial dialog in Plato’s "Gorgias", where Socrates confronts Calicles. The assumption is that this dialog is fundamental in Platonic philosophy, which is considered, in turn, a matrix in the philosophical project of Metaphysics. Such a view is conceived in "Gorgias" as a net of power and knowledge interrelations, established from a radical reflection about death as a basis for life and truth. This analysis intends to validate such hypothesis.

  20. Scientific Opinion on the safety evaluation of the process “CO.N.I.P.” used to recycle polypropylene and polyethylene crates for use as food contact material

    Directory of Open Access Journals (Sweden)

    EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids (CEF

    2013-04-01

    Full Text Available This scientific opinion of the EFSA Panel on Food Contact Materials, Enzymes, Flavourings and Processing Aids deals with the safety evaluation of the recycling process “CO.N.I.P.”, EC register number RECYC040. The process recycles single use food contact polypropylene (PP and high-density polyethylene (HDPE crates which have been used in a closed and controlled product loop into new recycled crates. Through this process, single use crates are firstly ground into flakes which may be used as such or further processed by extrusion or densification into granules. Recycled flakes or granules are used with or without blending with PP or HDPE offcuts or scrap to manufacture new recycled PP and HDPE crates by injection moulding. The Panel concluded that the input of the process “CO.N.I.P.” originates from a product loop which is in a closed and controlled chain ensuring that only materials and articles which have been intended for food contact are used and that any contamination can be ruled out when run under the conditions described by the applicant. The recycling process “CO.N.I.P.” is therefore able to produce recycled PP and HDPE suitable for manufacturing PP and HDPE crates intended to be used in contact with whole fruits and vegetables at room temperature or below as requested by the applicant.

  1. Confinement of lactating sows in crates for 4 days after farrowing reduces piglet mortality.

    Science.gov (United States)

    Moustsen, V A; Hales, J; Lahrmann, H P; Weber, P M; Hansen, C F

    2013-04-01

    To reduce mortality among suckling piglets, lactating sows are traditionally housed in farrowing crates. Alternatively, lactating sows can be housed in farrowing pens where the sow is loose to ensure more behavioural freedom and consequently a better welfare for the sow, although under commercial conditions, farrowing pens have been associated with increased piglet mortality. Most suckling piglets that die do so within the first week of life, so potentially lactating sows do not have to be restrained during the entire lactation period. Therefore, the aim of the current study was to investigate whether confinement of the sow for a limited number of days after farrowing would affect piglet mortality. A total of 210 sows (Danish Landrace × Danish Yorkshire) were farrowed in specially designed swing-aside combination farrowing pens measuring 2.6 m × 1.8 m (combi-pen), where the sows could be kept loose or in a crate. The sows were either: (a) loose during the entire experimental period, (b) crated from days 0 to 4 postpartum, (c) crated from days 0 to 7 postpartum or (d) crated from introduction to the farrowing pen to day 7 postpartum. The sows and their subsequent litters were studied from introduction to the combi-pen ∼1 week before expected farrowing and until 10 days postpartum. Confinement period of the sow failed to affect the number of stillborn piglets; however, sows that were crated after farrowing had fewer live-born mortality deaths (P piglet mortality among the loose sows was because of higher mortality in the first 4 days after farrowing. In conclusion, the current study demonstrated that crating the sow for 4 days postpartum was sufficient to reduce piglet mortality.

  2. Neopterin and biopterin as biomarkers of immune system activity associated with crating in broiler chickens.

    Science.gov (United States)

    Bedanova, I; Voslarova, E; Zelinska, G; Blahova, J; Marsalek, P; Chloupek, J

    2014-10-01

    Neopterin and biopterin belong to a group of unconjugated pterin derivates. These biomolecules are present in many animal species and perform several functions. Pterin concentrations may provide additional information on the effect of stress on immune system activity. This study focused on an investigation of the effect of crating on plasma concentrations of neopterin and biopterin in broilers. The effects of 2 crating periods (2 and 4 h) were monitored in Hubbard broilers (n = 90) aged 42 d. After a given crating period, randomly selected chickens from each group were sampled immediately and the remaining chickens were sampled after 24 h. Plasma corticosterone increased (P chickens. This is corroborated by the increase in plasma biopterin concentrations in broilers immediately after crating and the decrease in plasma neopterin concentrations in broilers 24 h after crating. The correlations were found for widely used indicators of acute and chronic stress in birds [i.e., plasma corticosterone concentrations (biopterin) and the heterophil-to-lymphocyte ratio (neopterin), respectively].

  3. Firmware development and testing of the ATLAS IBL Back-Of-Crate card

    CERN Document Server

    Stramaglia, ME; The ATLAS collaboration

    2014-01-01

    ATLAS is one of the four big LHC experiments and currently its Pixel-Detector is being upgraded with a new innermost 4th layer, the Insertable B-Layer (IBL). The upgrade will result in better tracking efficiency and compensate radiation damages of the Pixel-Detector. Newly developed front-end electronics and the higher than originally planned LHC luminosity will require a complete re-design of the Off-Detector-Electronics consisting of the Back-Of-Crate card (BOC) and the Read-Out-Driver (ROD). The main purpose of the BOC card is the distribution of the LHC clock to all Pixel-Detector components as well as interfacing the detector and the higher-level-readout optically. It is equipped with three Xilinx Spartan-6 FPGAs, one BOC Control FPGA (BCF) and two BOC Main FPGAs (BMF). The BMF are responsible for the signal processing of all incoming and outgoing data. The data-path to the detector is running a 40 MHz bi-phase-mark encoded stream. This stream is delayed by a fine delay block using Spartan-6 IODELAY prim...

  4. Will VAMS Reinforce the Walls of the Egg-Crate School?

    Science.gov (United States)

    Johnson, Susan Moore

    2015-01-01

    Throughout the United States there is an increasing trend toward using value-added methods (VAMs) for high-stakes decisions. When policymakers use VAMs to identify, reward, and dismiss teachers, they may perpetuate the egg-crate model of schooling and undermine efforts to build instructional capacity schoolwide. At any time, in any school, some…

  5. Esculturas de Hipócrates, Galeno y Manuel Plata Azuero

    Directory of Open Access Journals (Sweden)

    Alberto Albornoz Plata

    1996-08-01

    Full Text Available

    Dos agradables y emotivas sorpresas hemos experimentado en la tarde de hoy:

    Bellas obras de arte son las esculturas de Hipócrates y Galeno, que parecen saludar a todos los visitantes de la Academia al penetrar al salón principal. Por eso he querido recordar brevemente lo que estos personajes representan en la historia de la Medicina mundial y nacional.

    I. Hipócrates.

    Hipócrates.Nació en la isla griega de Cos, en el mar Egeo, en el año 4,60 A.c. Estudió medicina en Selymbria y sus maestros fueron Gorgias de Leontini y Demócrates. Muere en Tesalia a los 85 años. Fue muy distinguido por Platón y Aristóteles y es considerado universalmente como el Padre de la Medicina.

    Laennec, el famoso clínico francés del siglo XIX, lo consideró como genial por haber descrito tanto la sucusión torácica como la facies de los moribundos: ambas, en su honor, llevan el calificativo de “hipocráticas”. Hipócrates sostenía que la misma naturaleza cura las enfermedades. El “Corpus Hipocraticum”, que llegó hasta el Renacimiento por vía de los romanos y de los árabes, compendia el conocimiento médico de toda la antigüedad.

    El Juramento Hipocrático es su gran legado para los médicos: todos nosotros hemos prometido cumplirlo fielmente...

  6. O cidadão Sócrates e o filosofar numa democracia

    OpenAIRE

    2010-01-01

    Examinando o julgamento de Sócrates (470-399 a.C.) por Atenas, no contexto da Guerra do Peloponeso (431-404 a.C.), este texto busca as raízes, as razões e os significados de sua condenação nas críticas relações entre o filósofo e seus concidadãos. Neste caso - justamente no que podemos chamar de ''o caso Sócrates'' - o filósofo aparece (de conformidade com a Apologia escrita por Platão) como um cidadão-filósofo que desafia o Estado ateniense e incomoda seus concidadãos na medida em que exerce...

  7. crates sofista, Brás Cubas filósofo?

    Directory of Open Access Journals (Sweden)

    Alex Lara Martins

    2009-12-01

    Full Text Available Nosso objetivo é comparar as estratégias argumentativas de Sócrates e Brás Cubas, tais como ironia e aporia. Consideramos a estrutura ficcional machadiana como condição para a expressão cética, que ao desconfiar da realidade ou do que dela se supõe saber, instaura uma nova perspectiva, ou seja, outro nível de realidade que prescinde dos valores dogmáticos como Verdade e Essência. A justificativa geral para esse tipo de abordagem é que as questões ali descritas são encorpadas por situações ficcionais, gerando um ceticismo que se expressa numa obra de ficção. Brás Cubas e Sócrates esboçam conjecturas que descrevem as relações paradoxais do ser humano.

  8. El determinismo ambiental en dos autores clásicos : Hipócrates y Herodoto

    OpenAIRE

    García González, José Antonio

    2005-01-01

    El interés por la influencia que el clima y el medio ambiente ejercen sobre la vida en general, y sobre el hombre en particular, no es nuevo. Comprobamos a través del estudio de la obra de autores como Heródoto e Hipócrates, y de sus posturas ante el determinismo ambiental, como en la antigüedad se empieza a fraguar la toma de conciencia sobre estos temas. Toma de conciencia que hoy día se está reclamando a nuestra sociedad desde todas las esferas del conocimiento. The inter...

  9. A high performance real-time plasma control and event detection DSP based VME system

    Energy Technology Data Exchange (ETDEWEB)

    Rodrigues, A.P. E-mail: pinto@ci.uc.pt; Correia, Carlos; Varandas, Carlos

    2002-06-01

    This paper describes the digital signal processors module of a high performance system, specially designed for real-time plasma control and event detection on the next generation fusion experiments with long duration discharges. The system is composed of a commercial CPU board and several on-site developed intelligent modules inserted in the same VME crate.

  10. Crates: High-Level I/O Interface for Scripting Languages

    Science.gov (United States)

    Cresitello-Dittmar, M.; Burke, D.; Doe, S.; Evans, I.; Evans, J.; Germain, G.; Lyn, J.

    2007-10-01

    Crates is a new software package being developed by the Chandra X-Ray Center (CXC) to provide a high level I/O interface for use within various scripting environments. It consists of a set of classes and methods which allow a user to easily access and manipulate general data files as well as specialized classes for specific data products (PHA Type I & II, RMF, ARF, etc.). CRATES also provides convenient access to metadata information, such as WCS transforms and DM subspace information which may be associated with a table column or image. The core library is written in C++ and utilizes the CXC DataModel (DM) library, which provides I/O support for the Chandra Data Analysis software, and is designed to be extensible to multiple scripting environments. We provide a set of Python wrappers and functionality from within the SLang environment via PySL. The interface has a common look and feel with the CIAO application packages Sherpa, a general purpose fitting and modeling application, and ChIPS, the Chandra Imaging and Plotting System.

  11. Arduino based laser control

    OpenAIRE

    Bernal Muñoz, Ferran

    2015-01-01

    ARDUINO is a vey usefull platform for prototypes. In this project ARDUINO will be used for controling a Semiconductor Tuneable Laser. [ANGLÈS] Diode laser for communications control based on an Arduino board. Temperature control implementation. Software and hardware protection for the laser implementation. [CASTELLÀ] Control de un láser de comunicaciones ópticas desde el ordenador utilizando una placa Arduino. Implementación de un control de temperatura y protección software y hardware ...

  12. Arduino based laser control

    OpenAIRE

    Bernal Muñoz, Ferran

    2015-01-01

    ARDUINO is a vey usefull platform for prototypes. In this project ARDUINO will be used for controling a Semiconductor Tuneable Laser. [ANGLÈS] Diode laser for communications control based on an Arduino board. Temperature control implementation. Software and hardware protection for the laser implementation. [CASTELLÀ] Control de un láser de comunicaciones ópticas desde el ordenador utilizando una placa Arduino. Implementación de un control de temperatura y protección software y hardware ...

  13. Proposal for the award of a contract for the electronic instrumentation cards and crates for the LHC cryogenic system

    CERN Document Server

    2005-01-01

    This document concerns the award of a contract for the manufacturing, assembly, testing and delivery of the electronic instrumentation cards and crates for the LHC cryogenic system. The Finance Committee is invited to agree to the negotiation of a contract with JUTRON (FI), the lowest bidder, for the manufacture, assembly, testing and delivery of the electronic instrumentation cards and crates for the LHC cryogenic system for a total amount of 1 217 950 euros (1 875 444 Swiss francs), not subject to revision. The rate of exchange used is that stipulated in the tender.

  14. Estimating the economic impact of the adoption of novel non-crate sow farrowing systems in the UK

    OpenAIRE

    Cain, P.J.; Guy, J.G.; Seddon, Y.; Baxter, Emma M.; Edwards, S E

    2013-01-01

    The majority of indoor sows in the UK (around 95 per cent) farrow in conventional farrowing crates. There is pressure from a number of quarters – EU and national regulators, supermarket buyers and consumers – to improve the welfare of sows by adopting ‘‘free’’ farrowing systems. A DEFRA-funded project (under the acronym PigSAFE) conducted by Newcastle University and the Scottish Agricultural College (SAC) has developed and tested such a non-crate farrowing system. The trial monito...

  15. Ontology Based Access Control

    Directory of Open Access Journals (Sweden)

    Özgü CAN

    2010-02-01

    Full Text Available As computer technologies become pervasive, the need for access control mechanisms grow. The purpose of an access control is to limit the operations that a computer system user can perform. Thus, access control ensures to prevent an activity which can lead to a security breach. For the success of Semantic Web, that allows machines to share and reuse the information by using formal semantics for machines to communicate with other machines, access control mechanisms are needed. Access control mechanism indicates certain constraints which must be achieved by the user before performing an operation to provide a secure Semantic Web. In this work, unlike traditional access control mechanisms, an "Ontology Based Access Control" mechanism has been developed by using Semantic Web based policies. In this mechanism, ontologies are used to model the access control knowledge and domain knowledge is used to create policy ontologies.

  16. Opto-box: Optical modules and mini-crate for ATLAS pixel and IBL detectors

    Science.gov (United States)

    Bertsche, David

    2016-11-01

    The opto-box is a custom mini-crate for housing optical modules which process and transfer optoelectronic data. Many novel solutions were developed for the custom design and manufacturing. The system tightly integrates electrical, mechanical, and thermal functionality into a small package of size 35×10x8 cm3. Special attention was given to ensure proper shielding, grounding, cooling, high reliability, and environmental tolerance. The custom modules, which incorporate Application Specific Integrated Circuits, were developed through a cycle of rigorous testing and redesign. In total, fourteen opto-boxes have been installed and loaded with modules on the ATLAS detector. They are currently in operation as part of the LHC run 2 data read-out chain. This conference proceeding is in support of the poster presented at the International Conference on New Frontiers in Physics (ICNFP) 2015 [1].

  17. Opto-box: Optical modules and mini-crate for ATLAS pixel and IBL detectors

    Directory of Open Access Journals (Sweden)

    Bertsche David

    2016-01-01

    Full Text Available The opto-box is a custom mini-crate for housing optical modules which process and transfer optoelectronic data. Many novel solutions were developed for the custom design and manufacturing. The system tightly integrates electrical, mechanical, and thermal functionality into a small package of size 35×10x8 cm3. Special attention was given to ensure proper shielding, grounding, cooling, high reliability, and environmental tolerance. The custom modules, which incorporate Application Specific Integrated Circuits, were developed through a cycle of rigorous testing and redesign. In total, fourteen opto-boxes have been installed and loaded with modules on the ATLAS detector. They are currently in operation as part of the LHC run 2 data read-out chain. This conference proceeding is in support of the poster presented at the International Conference on New Frontiers in Physics (ICNFP 2015 [1].

  18. Sobre a presença de Sócrates na psicanálise

    Directory of Open Access Journals (Sweden)

    Anna Carolina Lo Bianco

    2001-01-01

    Full Text Available Não tendo deixado uma obra escrita, podemos dizer que o pensamento de Sócrates que chega até nós é fundado sobre um ponto básico, central e caro também à experiência psicanalítica: o da presença diante do outro. O artigo examina as características que cercam o exercício do procedimento socrático, ressaltando o impacto que ele tem sobre o interlocutor. Procura, em seguida, tomar a sua riqueza de princípios para ver, com as lentes da própria psicanálise, em que estes oferecem algumas condições de possibilidade para o melhor desenvolvimento de suas formulações.

  19. Firmware development and testing of the ATLAS IBL Back Of Crate card

    CERN Document Server

    Stramaglia, Maria Elena; The ATLAS collaboration

    2015-01-01

    ATLAS is one of the four big LHC experiments and currently its Pixel Detector was upgraded with a new innermost 4th layer: the Insertable B-Layer (IBL). The upgrade will result in better tracking efficiency and compensate radiation damages of the Pixel-Detector. Newly developed front-end electronics and the higher than originally planned LHC luminosity required a complete re-design of the Off Detector Electronics consisting of the Back Of Crate card (BOC) and the Read Out Driver (ROD). The main purpose of the BOC card is the distribution of the LHC clock to all Pixel Detector components as well as interfacing the detector and the higher level readout optically. The data-path to the detector is running a 40 MHz bi phase mark (BPM) encoded stream. The 160 MHz 8b10b encoded data path from the detector is phase and word aligned in the firmware and then forwarded to the ROD after decoding. The ROD will send out the processed data which is then forwarded to the higher level readout by the BOC card. An overview of t...

  20. Clinical records anonymisation and text extraction (CRATE): an open-source software system.

    Science.gov (United States)

    Cardinal, Rudolf N

    2017-04-26

    Electronic medical records contain information of value for research, but contain identifiable and often highly sensitive confidential information. Patient-identifiable information cannot in general be shared outside clinical care teams without explicit consent, but anonymisation/de-identification allows research uses of clinical data without explicit consent. This article presents CRATE (Clinical Records Anonymisation and Text Extraction), an open-source software system with separable functions: (1) it anonymises or de-identifies arbitrary relational databases, with sensitivity and precision similar to previous comparable systems; (2) it uses public secure cryptographic methods to map patient identifiers to research identifiers (pseudonyms); (3) it connects relational databases to external tools for natural language processing; (4) it provides a web front end for research and administrative functions; and (5) it supports a specific model through which patients may consent to be contacted about research. Creation and management of a research database from sensitive clinical records with secure pseudonym generation, full-text indexing, and a consent-to-contact process is possible and practical using entirely free and open-source software.

  1. ISÓCRATES Y LOS "ESPEJOS DE PRINCIPE" BIZANTINOS Isocrates and the Bizantine "Mirrors of princess"

    Directory of Open Access Journals (Sweden)

    Roberto Andrés Soto Ayala

    2011-10-01

    Full Text Available El artículo presenta un ordenado recuento de los géneros de la retórica bizantina y expone las características principales de cada uno de ellos, analizando con mayor detenimiento el de los denominados "Espejos de Príncipe". El estudio, respetando las debidas denominaciones epistemológicas en lengua griega, muestra cómo las composiciones parenéticas bizantinas de este género se vinculan, histórica y filológicamente, con la tradición retórica antigua de Isócrates.This article presents an orderly account of the genres of Byzantine rhetoric and exposes the main features of each, looking more closely at the so-called "mirror of princes." The study, in accordance with due epistemological Greek names, shows how Byzantine parenetic compositions of this kind are related, historical and philological, with the ancient rhetorical tradition of Isocrates.

  2. Diccionario histórico de la traducción en España : Hipócrates

    OpenAIRE

    Labiano, Mikel

    2009-01-01

    En el presente artículo nos proponemos pasar revista a las más importantes traducciones realizadas en España del médico griego Hipócrates, desde el Renacimiento a la actualidad. In this paper we will review the most important translations made in Spain of the Greek physician Hippocrates, from the Renaissance up the present day.

  3. Actualización y breve repaso de las traducciones de Hipócrates en España

    OpenAIRE

    Labiano, Mikel

    2009-01-01

    En el presente artículo nos proponemos pasar revista a las más importantes traducciones realizadas en España del médico griego Hipócrates, desde el Renacimiento a la actualidad. In this paper we will review the most important translations made in Spain of the Greek physician Hippocrates, from the Renaissance up the present day.

  4. Diccionario histórico de la traducción en España : Hipócrates

    OpenAIRE

    Labiano, Mikel

    2009-01-01

    En el presente artículo nos proponemos pasar revista a las más importantes traducciones realizadas en España del médico griego Hipócrates, desde el Renacimiento a la actualidad. In this paper we will review the most important translations made in Spain of the Greek physician Hippocrates, from the Renaissance up the present day.

  5. Sow postural changes, responsiveness to piglet screams, and their impact on piglet mortality in pens and crates.

    Science.gov (United States)

    Melišová, M; Illmann, G; Chaloupková, H; Bozděchová, B

    2014-07-01

    Free farrowing pens (pens) improve the welfare of sows but may increase sow activity and negatively influence piglet production. The aim of this study was to assess the effect of pens and crates on sow postural changes, piglet trapping, sow responses to piglet screams, piglet mortality, and piglet BW gain. It was predicted that provision of greater space (in pens) would increase not only the frequency of sow postural changes and the probability of trappisng but also sow responses to the screams of piglets; thus, the outcome would be no differences in fatal piglet crushing or overall mortality between the housing systems. Sows were randomly moved to either a farrowing pen (n = 20) or farrowing crate (n = 18). Sow behavior was recorded and analyzed for 72 h from the birth of the first piglet (BFP). Sow postural changes included rolling from a ventral to lateral position and vice versa and going from standing to sitting, standing to lying, and sitting to lying. Occurrences of piglet trapping and sow responsiveness to real crushing situations were analyzed. Sow responsiveness was assessed in response to audio playbacks (PB) of piglet screams on d 3 postpartum (48 to 72 h after BFP; PB crush calls) and real piglet crushing during the first 72 h after BFP (real crush calls). Piglet BW gain was estimated 24 h after BFP, piglet BW was recorded at weaning, and piglet crushing and piglet mortality were recorded during the 72 h after BFP. Data were analyzed using PROC MIXED and PROC GENMOD of SAS. Sows in pens showed more postural changes (P = 0.04) and tended to have greater incidences of piglet trapping (P = 0.07) than those in crates. Sow response to PB crush calls was greater in pens (P = 0.04) but did not differ for real crush calls between pens and crates (P = 0.62). There was no effect on the probability of piglet crushing (P = 0.38) and mortality (P = 0.41) during the 72 h after BFP nor in piglet mortality at weaning (P = 0.81) between pens and crates. Piglet BW gain

  6. The behaviour and welfare of sows and piglets in farrowing crates or lactation pens.

    Science.gov (United States)

    Singh, C; Verdon, M; Cronin, G M; Hemsworth, P H

    2017-07-01

    Temporary confinement during parturition and early postpartum may provide an intermediary step preceding loose housing that offers improvement in sow and piglet welfare. Three experiments were conducted to investigate the implications of replacing farrowing crates (FCs) with an alternative housing system from 3 days postpartum until weaning. In each experiment sows farrowed in FCs and were randomly allocated at day 3 of lactation to either a FC or a pen with increased floor space (lactation pen (LP)) until weaning. In experiment 1, piglet growth and sow and piglet skin injuries were recorded for 32 sows and 128 focal piglets in these litters. Behaviour around nursing and piglet behavioural time budgets were also recorded for 24 of these litters (96 focal piglets for time budgets). In experiment 2, measures of skin injury and behavioural time budgets were conducted on 28 sows and 112 focal piglets. The behavioural response of sows to piglet vocalisation (maternal responsiveness test (MRT)) was also assessed. In experiment 3, piglet mortality from day 3 of lactation until weaning was recorded in 672 litters over 12 months. While housing did not affect piglet weight gain in experiment 1, or piglet skin injuries in experiments 1 or 2, sows in both experiments sustained more injuries in LP than FC (experiment 1, 2.9 v. 1.4; experiment 2, 2.5 v. 0.8 lesions/sow; P0.05). Thus, housing sows and litters in LP from day 3 of lactation minimises piglet mortality while improving maternal behaviour in sows and social behaviour in piglets.

  7. Methods in Logic Based Control

    DEFF Research Database (Denmark)

    Christensen, Georg Kronborg

    1999-01-01

    Desing and theory of Logic Based Control systems.Boolean Algebra, Karnaugh Map, Quine McClusky's algorithm. Sequential control design. Logic Based Control Method, Cascade Control Method. Implementation techniques: relay, pneumatic, TTL/CMOS,PAL and PLC- and Soft_PLC implementation. PLC-design met......Desing and theory of Logic Based Control systems.Boolean Algebra, Karnaugh Map, Quine McClusky's algorithm. Sequential control design. Logic Based Control Method, Cascade Control Method. Implementation techniques: relay, pneumatic, TTL/CMOS,PAL and PLC- and Soft_PLC implementation. PLC...

  8. Methods in Logic Based Control

    DEFF Research Database (Denmark)

    Christensen, Georg Kronborg

    1999-01-01

    Desing and theory of Logic Based Control systems.Boolean Algebra, Karnaugh Map, Quine McClusky's algorithm. Sequential control design. Logic Based Control Method, Cascade Control Method. Implementation techniques: relay, pneumatic, TTL/CMOS,PAL and PLC- and Soft_PLC implementation. PLC...

  9. Utilization-Based Congestion Control

    OpenAIRE

    Satoshi Utsumi; Salahuddin Muhammad Salim Zabir

    2012-01-01

    Traditional connection oriented protocols like TCP NewReno perform poorly over wireless links. Theproblem lies in their design assumptions based on loss based congestion control. Various modificationsto loss based congestion control schemes have so far been proposed to overcome the issue. In addition,the comparatively newer family of delay based congestion control mechanisms like Caia-Hamilton Delay(CHD), offer effective solutions for wireless link loss. All these approaches aim at improving ...

  10. Unfalsified control based on the ? controller parameterisation

    Science.gov (United States)

    Sánchez-Peña, R. S.; Colmegna, P.; Bianchi, F.

    2015-11-01

    This paper presents an implementation of the unfalsified control (UC) method using the Riccati-based parameterisation of ? controllers. The method provides an infinite controller set to (un)falsify the real-time data streams seeking for the best performance. Different sets may be designed to increase the degrees of freedom of the set of controller candidates to perform UC. In general, a set of m central controllers could be designed, each one seeking different objectives and all with their own parameterisation as a function of a stable and bounded transfer matrix. For example, one controller parameterisation could be designed to solve the robust stability of a model set which covers the physical system, therefore guaranteeing feasibility. The implementation requires the online optimisation of either quadratic fractional or quadratic problems, depending on the selection of the cost function. A multi-input, multi-output (MIMO) time-varying model of a permanent magnet synchronous generator illustrates the use of this technique.

  11. Where is the lithium? Quantitative determination of the lithium distribution in lithium ion battery cells: Investigations on the influence of the temperature, the C-rate and the cell type

    Science.gov (United States)

    Vortmann-Westhoven, Britta; Winter, Martin; Nowak, Sascha

    2017-04-01

    With lithium being the capacity determining species in lithium-ion battery (LIB) cells, the local quantification is of enormous importance for understanding of the cell performance. The investigation of the lithium distribution in LIB full cells is performed with two different cell types, T-cells of the Swagelok® type and pouch bag cells with lithium nickel cobalt manganese oxide and mesocarbon microbead graphite as the active materials as well as a lithium hexafluorophosphate based organic carbonate solvent electrolyte. The lithium content of/at the individual components of the cells is analyzed for different states of charge (SOCs) by inductively coupled plasma-optical emission spectrometry (ICP-OES) and the lithium distribution as well as the loss of active lithium within the cells is calculated after cycling. With increasing the SOC, the lithium contents decrease in the cathodes and simultaneously increase in the anodes. The temperature increase shows a clear shift of the lithium content in the direction of the anode for the T-cells. The comparison of the C-rate influence shows that the lower the C-rate, the more the lithium content on the electrodes is shifted into the direction of the anode.

  12. An integrated computer control system for the ANU linac

    Science.gov (United States)

    Davidson, P. M.; Foote, G. S.

    1996-02-01

    One facet of the installation of the superconducting linac at the ANU is the need for computer control of a variety of systems, such as beam transport, resonator RF, cryogenics and others. To accommodate this, a number of control interfaces (for example, analogue signals and RS232 serial lines) must be employed. Ideally, all of the systems should be able to be controlled from a central location, remote from the actual devices. To this end a system based around VAX computers and VME crates has been designed and is currently being developed and implemented. A VAXstation is used to issue control messages and perform high-level functions, while VME crates containing appropriate modules (primarily DACs, ADCs and digital I/O boards) control the devices. The controllers in the VME crates are AEON rtVAX modules running a real-time operating system. Communication with the VAXstation is via DECnet, on a private ethernet to allow communication rates unaffected by unrelated network activity and potentially increasing the security of the system by providing a possible network isolation point. Also on this ethernet are a number of terminal servers to control RS232 devices. A central database contains all device control and monitoring parameters. The main control process running on the VAXstation is responsible for maintaining the current values of the parameters in the database and for dispatching control messages to the appropriate VME crate or RS232 serial line. Separate graphical interface processes allow the operator to interact with the control process, communicating through shared memory. Many graphics processes can be active simultaneously, displaying either on a single or on multiple terminals. Software running on the rtVAX controllers handles the low-level device-specific control by translating messages from the main control process to VME commands which set hardware outputs on VME modules. Similarly, requests for the value of a parameter result in the rtVAX program

  13. Preparation of Advanced Carbon Anode Materials from Mesocarbon Microbeads for Use in High C-Rate Lithium Ion Batteries

    Directory of Open Access Journals (Sweden)

    Ming-Dar Fang

    2015-06-01

    Full Text Available Mesophase soft carbon (MSC and mesophase graphite (SMG, for use in comparative studies of high C-rate Lithium Ion Battery (LIB anodes, were made by heating mesocarbon microbeads (MCMB at 1300 °C and 3000 °C; respectively. The crystalline structures and morphologies of the MSC, SMG, and commercial hard carbon (HC were investigated by X-ray diffraction, transmission electron microscopy, scanning electron microscopy, and Raman spectroscopy. Additionally, their electrochemical properties, when used as anode materials in LIBs, were also investigated. The results show that MSC has a superior charging rate capability compared to SMG and HC. This is attributed to MSC having a more extensive interlayer spacing than SMG, and a greater number of favorably-oriented pathways when compared to HC.

  14. Process control using reliability based control charts

    Directory of Open Access Journals (Sweden)

    J.K. Jacob

    2008-12-01

    Full Text Available Purpose: The paper presents the method to monitor the mean time between failures (MTBF and detect anychange in intensity parameter. Here, a control chart procedure is presented for process reliability monitoring.Control chart based on different distributions are also considered and were used in decision making. Results anddiscussions are presented based on the case study at different industries.Design/methodology/approach: The failure occurrence process can be modeled by different distributions likehomogeneous Poisson process, Weibull model etc. In each case the aim is to monitor the mean time betweenfailure (MTBF and detect any change in intensity parameter. When the process can be described by a Poissonprocess the time between failures will be exponential and can be used for reliability monitoring.Findings: In this paper, a new procedure based on the monitoring of time to observe r failures is also proposedand it can be more appropriate for reliability monitoring.Practical implications: This procedure is useful and more sensitive when compared with the λ-chart although itwill wait until r failures for a decision. These charts can be regarded as powerful tools for reliability monitoring.λr gives more accurate results than λ-chart.Originality/value: Adopting these measures to system of equipments can increase the reliability and availabilityof the system results in economic gain. A homogeneous Poisson process is usually used to model the failureoccurrence process with certain intensity.

  15. Fuzzy logic based robotic controller

    Science.gov (United States)

    Attia, F.; Upadhyaya, M.

    1994-01-01

    Existing Proportional-Integral-Derivative (PID) robotic controllers rely on an inverse kinematic model to convert user-specified cartesian trajectory coordinates to joint variables. These joints experience friction, stiction, and gear backlash effects. Due to lack of proper linearization of these effects, modern control theory based on state space methods cannot provide adequate control for robotic systems. In the presence of loads, the dynamic behavior of robotic systems is complex and nonlinear, especially where mathematical modeling is evaluated for real-time operators. Fuzzy Logic Control is a fast emerging alternative to conventional control systems in situations where it may not be feasible to formulate an analytical model of the complex system. Fuzzy logic techniques track a user-defined trajectory without having the host computer to explicitly solve the nonlinear inverse kinematic equations. The goal is to provide a rule-based approach, which is closer to human reasoning. The approach used expresses end-point error, location of manipulator joints, and proximity to obstacles as fuzzy variables. The resulting decisions are based upon linguistic and non-numerical information. This paper presents a solution to the conventional robot controller which is independent of computationally intensive kinematic equations. Computer simulation results of this approach as obtained from software implementation are also discussed.

  16. crates y Nietzsche. Analogías entre naturaleza filosófica y espíritu libre

    OpenAIRE

    DEL PINO RODRÍGUEZ, IGNACIO

    2016-01-01

    Este trabajo se ocupa de Sócrates y Nietzsche. En concreto, de la analogía entre naturaleza filosófica y espíritu libre. En efecto, para decir cómo son sus filosofías haría falta una larga y divina explicación. Sin embargo, decir a qué se parecen una y otra es, desde luego, una tarea mucho más acorde al rango humano, y también algo más breve1. Luego, en tanto que analogía significa relación de semejanza entre cosas distintas, mi tesis es que las filosofías de Sócrates y Niet...

  17. Os dois sentidos da crítica nietzscheana: Sócrates como um caso exemplar = The two senses of the Nietzschean criticism: Socrates as an examplar case

    Directory of Open Access Journals (Sweden)

    Fonseca, Ana Carolina da Costa e

    2012-01-01

    Full Text Available Toma-se a crítica de Nietzsche a Sócrates como um caso exemplar que mostra os dois sentidos fundamentais da crítica nietzscheana: (i a crítica nietzscheana consiste em censura e em elogio de modo dual, ou seja, censura e elogio são aspectos da crítica; e (ii ao criticar alguém, Nietzsche está, igualmente, se autocriticando

  18. RF control hardware design for CYCIAE-100 cyclotron

    Energy Technology Data Exchange (ETDEWEB)

    Yin, Zhiguo, E-mail: bitbearAT@hotmail.com; Fu, Xiaoliang; Ji, Bin; Zhao, Zhenlu; Zhang, Tianjue; Li, Pengzhan; Wei, Junyi; Xing, Jiansheng; Wang, Chuan

    2015-11-21

    The Beijing Radioactive Ion-beam Facility project is being constructed by BRIF division of China Institute of Atomic Energy. In this project, a 100 MeV high intensity compact proton cyclotron is built for multiple applications. The first successful beam extraction of CYCIAE-100 cyclotron was done in the middle of 2014. The extracted proton beam energy is 100 MeV and the beam current is more than 20 μA. The RF system of the CYCIAE-100 cyclotron includes two half-wavelength cavities, two 100 kW tetrode amplifiers and power transmission line systems (all above are independent from each other) and two sets of Low Level RF control crates. Each set of LLRF control includes an amplitude control unit, a tuning control unit, a phase control unit, a local Digital Signal Process control unit and an Advanced RISC Machines based EPICS IOC unit. These two identical LLRF control crates share one common reference clock and take advantages of modern digital technologies (e.g. DSP and Direct Digital Synthesizer) to achieve closed loop voltage and phase regulations of the dee-voltage. In the beam commission, the measured dee-voltage stability of RF system is better than 0.1% and phase stability is better than 0.03°. The hardware design of the LLRF system will be reviewed in this paper.

  19. Bluetooth Based Android Controlled Robot

    Directory of Open Access Journals (Sweden)

    Rowjatul Zannat Eshita

    2016-06-01

    Full Text Available The project aims in designing a Robot that can be operated using Android Apps. The controlling of the Robot is done wirelessly through Android smart phone using the Bluetooth module feature present in it. Here in the project the Android smart phone is used as a remote control for operating the Robot. Android is a software stack for mobile devices that includes an operating system, middleware and key applications. Android boasts a healthy array of connectivity options, including Wi-Fi, Bluetooth, and wireless data over a cellular connection (for example, GPRS, EDGE (Enhanced Data rates for GSM Evolution, and 3G. Android provides access to a wide range of useful libraries and tools that can be used to build rich applications. Bluetooth is an open standard specification for a radio frequency (RF-based, short-range connectivity technology that promises to change the face of computing and wireless communication. It is designed to be an inexpensive, wireless networking system for all classes of portable devices, such as laptops, PDAs (personal digital assistants, and mobile phones. The controlling device of the whole system is a Microcontroller. Bluetooth module, DC motors are interfaced to the Microcontroller. The data received by the Bluetooth module from Android smart phone is fed as input to the controller. The controller acts accordingly on the DC motors of the Robot. The robot in the project can be made to move in all the four directions using the Android phone. The direction of the robot is indicated using LED indicators of the Robot system. In achieving the task the controller is loaded with a program written using Embedded ‘C’ language.

  20. Neonatal piglet traits of importance for survival in crates and indoor pens

    DEFF Research Database (Denmark)

    Pedersen, Lene Juul; Berg, Peer; Jørgensen, Grete

    2011-01-01

    ) were used. These were distributed to farrow in either PN or CT as follows: high-SR5 and CT (n = 30); low-SR5 and CT (n = 27); high-SR5 and PN (n = 22); and low-SR5 and PN (n = 24). Data on individual piglets were collected at birth, including interbirth interval; birth order; birth weight; rectal...... of mortality. Piglet traits for pre- and postnatal survival were the same for CT and PN. The odds of being stillborn were increased in piglets born late in the birth order (F1,1061 = 33.5, P birth weight (F1,1061 = 9...... temperature at birth, 2 h after birth, and 24 h after birth; cordal plasma lactate; and latency to first suckle. Based on autopsy, causes of mortality were divided into stillborn, bitten to death, starvation, crushed, disease, and other causes. Potential risk factors of dying were estimated using a GLM...

  1. Synthesis of Li-Rich Cathode Material with High C-Rate Performance by Reductive Treatment

    Science.gov (United States)

    Lim, Sung Nam; Seo, Jung Yoon; Song, Shin Ae; Kim, Ki Young; Park, Seung Bin; Jung, Dae Soo

    2017-01-01

    Li-rich cathode materials have intrinsically poor rate capability along with low electronic conductivity, which remain as unsolved drawbacks limiting their use in applications that require cathode material with layered structures. Here, we prepared surface-modified Li-rich cathode materials to address these drawbacks via reductive treatment. After reductive treatment, we confirmed that these samples feature better electrochemical performance; the reductive treated samples show higher capacity and better capacity retention during cycling compared to samples treated only in air. In particular, the reductive treated samples showed excellent rate capability of 168 mAh g-1 at a current density of 400 mA g-1 compared to 138 mAh g-1 for the air treated sample. We confirmed that reductive treatment reduces the resistance for charge transfer based on electrochemical impedance spectroscopy analysis. We also investigated the effects of reductive treatment on the cathode structure of both samples using x-ray diffraction as well as x-ray photoelectron spectroscopy.

  2. Synthesis of Li-Rich Cathode Material with High C-Rate Performance by Reductive Treatment

    Science.gov (United States)

    Lim, Sung Nam; Seo, Jung Yoon; Song, Shin Ae; Kim, Ki Young; Park, Seung Bin; Jung, Dae Soo

    2017-03-01

    Li-rich cathode materials have intrinsically poor rate capability along with low electronic conductivity, which remain as unsolved drawbacks limiting their use in applications that require cathode material with layered structures. Here, we prepared surface-modified Li-rich cathode materials to address these drawbacks via reductive treatment. After reductive treatment, we confirmed that these samples feature better electrochemical performance; the reductive treated samples show higher capacity and better capacity retention during cycling compared to samples treated only in air. In particular, the reductive treated samples showed excellent rate capability of 168 mAh g-1 at a current density of 400 mA g-1 compared to 138 mAh g-1 for the air treated sample. We confirmed that reductive treatment reduces the resistance for charge transfer based on electrochemical impedance spectroscopy analysis. We also investigated the effects of reductive treatment on the cathode structure of both samples using x-ray diffraction as well as x-ray photoelectron spectroscopy.

  3. Software based controls module development

    Energy Technology Data Exchange (ETDEWEB)

    Graves, v.b.; kelley, g; welch, j.c.

    1999-12-10

    A project was initiated at the Oak Ridge Y-12 Plant to implement software geometric error compensation within a PC-based machine tool controller from Manufacturing Data Systems, Inc. This project may be the first in which this type of compensation system was implemented in a commercially available machine tool controller totally in software. Previous implementations typically required using an external computer and hardware to interface through the position feedback loop of the controller because direct access to the controller software was not available. The test-bed machine for this project was a 2-axis Excello 921 T-base lathe. A mathematical error model of the lathe was created using homogeneous transformation matrices to relate the positions of the machine's slides to each other and to a world reference system. Equations describing the effects of the geometric errors were derived from the model. A software architecture was developed to support geometric error compensation for machine tools with up to 3 linear axes. Rotary axes were not supported in this implementation, but the developed architecture would not preclude their support in the future. Specific implementations will be dependent upon the configuration of the machine tool. A laser measuring system from Automated Precision, Inc. was used to characterize the lathe's geometric errors as functions of axis position and direction of motion. Multiple data files generated by the laser system were combined into a single Error File that was read at system startup and used by the compensation system to provide real-time position adjustments to the axis servos. A Renishaw Ballbar was used to evaluate the compensation system. Static positioning tests were conducted in an attempt to observe improved positioning accuracy with the compensation system enabled. These tests gave inconsistent results due to the lathe's inability to position the tool repeatably. The development of the architecture and

  4. SMS BASED REMOTE CONTROL SYSTEM

    Directory of Open Access Journals (Sweden)

    Reecha Ranjan Singh , Sangeeta Agrawal , Saurabh Kapoor ,S. Sharma

    2011-08-01

    Full Text Available A modern world contains varieties of electronic equipment and systems like: TV, security system, Hi-fi equipment, central heating systems, fire alarm systems, security alarm systems, lighting systems, SET Top Box, AC (Air Conditioner etc., we need to handle, ON/OFF or monitor these electrical devices remotely or to communicate with these but, if you are not at the home or that place and you want to communicate with these device. So the new technology for handled these devices remotely and for communication to required the GSM, mobile technology, SMS (short message service and some hardware resources. SMS based remote control for home appliances is beneficial for the human generation, because mobile is most recently used technology nowadays.

  5. Fuzzy cascade control based on control's history for superheated temperature

    Institute of Scientific and Technical Information of China (English)

    WANG Guangjun; LI Gang; SHEN Shuguang

    2007-01-01

    To address the characteristics of the large delay and uncertainty of superheated temperature,a new cascade control system is presented based on control's history.Based on the analysis of the control objects' dynamic characteristics,historical control information (substituting for the deviation change rate) is used as the basis for decision-making of the fuzzy control.Therefore,the changing trend of the controlled variable can be accurately reflected.Furthermore,a proportional component is introduced,the advantages of PID and fuzzy controllers are integrated,and the structure weaknesses of conventional fuzzy controllers are overcome.Simulation shows that this control method can effectively reduce the adverse impact of the delay on control effects and,therefore,exhibit strong adaptability by comparing the superheated temperature control system by this controller with PID and conventional fuzzy controllers.

  6. Control of Unknown Chaotic Systems Based on Neural Predictive Control

    Institute of Scientific and Technical Information of China (English)

    LIDong-Mei; WANGZheng-Ou

    2003-01-01

    We introduce the predictive control into the control of chaotic system and propose a neural network control algorithm based on predictive control. The proposed control system stabilizes the chaotic motion in an unknown chaotic system onto the desired target trajectory. The proposed algorithm is simple and its convergence speed is much higher than existing similar algorithms. The control system can control hyperchaos. We analyze the stability of the control system and prove the convergence property of the neural controller. The theoretic derivation and simulations demonstrate the effectiveness of the algorithm.

  7. Agent-Based Cooperative Control

    Science.gov (United States)

    2005-12-01

    IEEE Transactions on Automatic Control , vol. 45, issue 12, Dec, 2000, pp. 2253-2270. [15] A. M. Bloch, Dong Eui Chang, N. E. Leonard, J. E...Marsden, “Controlled Lagrangians and the stabilization of mechanical systems. II. Potential shaping,” IEEE Transactions on Automatic Control , vol. 46...a new approach to constructive nonlinear control,” IEEE Transactions on Automatic Control , Volume 49, Issue 7, July

  8. Harpócrates y la iconografía del poder imperial en las acuñaciones nomaicas de Trajano y Antonino Pío

    OpenAIRE

    Domingo Saura Zorilla

    2007-01-01

    Egipto presenta en época de los emperadores Antoninos unas series monetales excepcionales de tipo provincial, o mejor «subprovincial», pues están batidas en los nomos o distritos egipcios, apareciendo sus nombres geográficos escritos en los reversos; y junto a las leyendas se muestran las imágenes de las divinidades tutelares, Isis, Horus-Harpócrates, etc. Así pues, anversos y reversos se complementan en las monedas ofreciendo una iconografía religiosa local egipcia en apoyo de la ideología i...

  9. Microprocessor-Based Valved Controller

    Science.gov (United States)

    Norman, Arnold M., Jr.

    1987-01-01

    New controller simpler, more precise, and lighter than predecessors. Mass-flow controller compensates for changing supply pressure and temperature such as occurs when gas-supply tank becomes depleted. By periodically updating calculation of mass-flow rate, controller determines correct new position for valve and keeps mass-flow rate nearly constant.

  10. O cidadão Sócrates e o filosofar numa democracia Socrates as a citizen and the act of philosophizing in a democracy

    Directory of Open Access Journals (Sweden)

    Roberto Goto

    2010-04-01

    Full Text Available Examinando o julgamento de Sócrates (470-399 a.C. por Atenas, no contexto da Guerra do Peloponeso (431-404 a.C., este texto busca as raízes, as razões e os significados de sua condenação nas críticas relações entre o filósofo e seus concidadãos. Neste caso - justamente no que podemos chamar de ''o caso Sócrates'' - o filósofo aparece (de conformidade com a Apologia escrita por Platão como um cidadão-filósofo que desafia o Estado ateniense e incomoda seus concidadãos na medida em que exerce a cidadania como uma forma de filosofar e pratica a filosofia como um direito e um dever de cidadania.This article examines the trial of Socrates (470-399 B.C. by Athens, in the context of the Peloponnesian War (431-404 B.C., searching for the roots, reasons and meanings of his condemnation in the critical relations between the philosopher and his fellow citizens. In this case - exactly in what we can call ''the Socrates case'' - the philosopher appears (according to Plato's Apology as a citizen-philosopher who challenges the Athenian State and disturbs his fellow citizens while he exercises citizenship as a form of philosophizing and practices philosophy as a right and a duty of citizenship.

  11. Notas heréticas sobre lógica y sofística en la “Apología de Sócrates

    Directory of Open Access Journals (Sweden)

    Sírio Lopez Vélasco

    2016-10-01

    Full Text Available En este trabajo sometemos a análisis crítico (desde el punto de vista de la lógica y del rechazo a la sofística  la conducta y discurso  del maestro Platón en la obra destinada a perpetuar su gloriosa memoria: la “Apología de Sócrates”. Veremos que en su autodefensa Sócrates incurre en equívocos lógicos y usa diversos recursos de tipo sofístico (que bien hubieran podido servir a su principal acusador, Meleto. Así nuestra lectura humaniza al personaje y contribuye a hacer menos clara la neta línea divisoria que Platón intentó trazar entre su maestro y los sofistas (línea, que por cierto, no existía en la visión que de Sócrates nos pintó Aristófanes en “Las Nubes”.

  12. Control of Unknown Chaotic Systems Based on Neural Predictive Control

    Institute of Scientific and Technical Information of China (English)

    LI Dong-Mei; WANG Zheng-Ou

    2003-01-01

    We introduce the predictive control into the control of chaotic system and propose a neural networkcontrol algorithm based on predictive control. The proposed control system stabilizes the chaotic motion in an unknownchaotic system onto the desired target trajectory. The proposed algorithm is simple and its convergence speed is muchhigher than existing similar algorithms. The control system can control hyperchaos. We analyze the stability of thecontrol system and prove the convergence property of the neural controller. The theoretic derivation and simulationsdemonstrate the effectiveness of the algorithm.

  13. Audit-based compliance control

    NARCIS (Netherlands)

    Cederquist, J.G.; Corin, R.; Dekker, M.A.C.; Etalle, S.; Hartog, J.I. den; Lenzini, G.

    2007-01-01

    In this paper we introduce a new framework for controlling compliance to discretionary access control policies [Cederquist et al. in Proceedings of the International Workshop on Policies for Distributed Systems and Networks (POLICY), 2005; Corin et al. in Proceedings of the IFIP Workshop on Formal A

  14. Noninteracting control of nonlinear systems based on relaxed control

    NARCIS (Netherlands)

    Jayawardhana, B.

    2010-01-01

    In this paper, we propose methodology to solve noninteracting control problem for general nonlinear systems based on the relaxed control technique proposed by Artstein. For a class of nonlinear systems which cannot be stabilized by smooth feedback, a state-feedback relaxed control can be designed to

  15. A Lyapunov theory based UPFC controller for power flow control

    Energy Technology Data Exchange (ETDEWEB)

    Zangeneh, Ali; Kazemi, Ahad; Hajatipour, Majid; Jadid, Shahram [Center of Excellence for Power Systems Automation and Operation, Iran University of Science and Technology, Tehran (Iran)

    2009-09-15

    Unified power flow controller (UPFC) is the most comprehensive multivariable device among the FACTS controllers. Capability of power flow control is the most important responsibility of UPFC. According to high importance of power flow control in transmission lines, the proper controller should be robust against uncertainty and disturbance and also have suitable settling time. For this purpose, a new controller is designed based on the Lyapunov theory and its stability is also evaluated. The Main goal of this paper is to design a controller which enables a power system to track reference signals precisely and to be robust in the presence of uncertainty of system parameters and disturbances. The performance of the proposed controller is simulated on a two bus test system and compared with a conventional PI controller. The simulation results show the power and accuracy of the proposed controller. (author)

  16. Bluetooth Based Android Controlled Robot

    National Research Council Canada - National Science Library

    Rowjatul Zannat Eshita; Tanwy Barua; Arzon Barua; Anik Mahamood Dip

    2016-01-01

    The project aims in designing a Robot that can be operated using Android Apps. The controlling of the Robot is done wirelessly through Android smart phone using the Bluetooth module feature present...

  17. Adaptive fuzzy controllers based on variable universe

    Institute of Scientific and Technical Information of China (English)

    李洪兴

    1999-01-01

    Adaptive fuzzy controllers by means of variable universe are proposed based on interpolation forms of fuzzy control. First, monotonicity of control rules is defined, and it is proved that the monotonicity of interpolation functions of fuzzy control is equivalent to the monotonicity of control rules. This means that there is not any contradiction among the control rules under the condition for the control rules being monotonic. Then structure of the contraction-expansion factor is discussed. At last, three models of adaptive fuzzy control based on variable universe are given which are adaptive fuzzy control model with potential heredity, adaptive fuzzy control model with obvious heredity and adaptive fuzzy control model with successively obvious heredity.

  18. Adaptive Fuzzy Knowledge Based Controller for Autonomous Robot Motion Control

    Directory of Open Access Journals (Sweden)

    Mbaitiga Zacharie

    2010-01-01

    Full Text Available Problem statement: Research into robot motion control offers research opportunities that will change scientists and engineers for year to come. Autonomous robots are increasingly evident in many aspects of industry and everyday life and a robust robot motion control can be used for homeland security and many consumer applications. This study discussed the adaptive fuzzy knowledge based controller for robot motion control in indoor and outdoor environment. Approach: The proposed method consisted of two components: the process monitor that detects changes in the process characteristics and the adaptation mechanism that used information passed to it by the process monitor to update the controller parameters. Results: Experimental evaluation had been done in both indoor and outdoor environment where the robot communicates with the base station through its Wireless fidelity antenna and the performance monitor used a set of five performance criteria to access the fuzzy knowledge based controller. Conclusion: The proposed method had been found to be robust.

  19. Gesture & Speech Based Appliance Control

    Directory of Open Access Journals (Sweden)

    Dr. Sayleegharge,

    2014-01-01

    Full Text Available This document explores the use of speech & gestures to control home appliances. Aiming at the aging population of the world and relieving them from their dependencies. The two approaches used to sail through the target are the MFCC approach for speech processing and the Identification of Characteristic Point Algorithm for gesture recognition. A barrier preventing wide adoption is that this audience can find controlling assistive technology difficult, as they are less dexterous and computer literate. Our results hope to provide a more natural and intuitive interface to help bridge the gap between technology and elderly users.

  20. Brushless DC Motor Speed Control Based on Emotional Intelligent Controller

    Directory of Open Access Journals (Sweden)

    Gholamreza ArabMarkadeh

    2014-03-01

    Full Text Available This paper presents an emotional controller for brushless DC motor (BLDC drive. The proposed controller is called brain emotional learning based intelligent controller (BELBIC. The utilization of the new controller is based on the emotion processing mechanism in brain. This intelligent control is inspired by the limbic system of mammalian brain, especially amygdala. The controller is successfully implemented in simulation using MATLAB software, brushless dc drive with trapezoidal back-emf. In this work, a novel and simple implementation of BLDC motor drive system is achieved by using the intelligent controller, which controls the motor speed accurately. This emotional intelligent controller has simple structure with high auto learning feature. Simulation results show that both accurate steady state and fast transient speed responses can be achieved in wide range of speed from 20 to 300 [rpm]. Moreover, to evaluate this emotional controller, the performance of the proposed control scheme is compared with both Fuzzy Logic (FL and PID controllers, in different conditions. This indicates proper operating in comparison to the FLC and PID controllers. And also shows excellent promise for industrial scale utilization.

  1. Disturbance observer based current controller for vector controlled IM drives

    DEFF Research Database (Denmark)

    Teodorescu, Remus; Dal, Mehmet

    2008-01-01

    In order to increase the accuracy of the current control loop, usually, well known parameter compensation and/or cross decoupling techniques are employed for advanced ac drives. In this paper, instead of using these techniques an observer-based current controller is proposed for vector controlled...... coupling effects and increase robustness against parameters change without requiring any other compensation strategies. The experimental implementation results are provided to demonstrate validity and performance of the proposed control scheme.......In order to increase the accuracy of the current control loop, usually, well known parameter compensation and/or cross decoupling techniques are employed for advanced ac drives. In this paper, instead of using these techniques an observer-based current controller is proposed for vector controlled...

  2. Genetic Algorithm based Decentralized PI Type Controller: Load Frequency Control

    Science.gov (United States)

    Dwivedi, Atul; Ray, Goshaidas; Sharma, Arun Kumar

    2016-12-01

    This work presents a design of decentralized PI type Linear Quadratic (LQ) controller based on genetic algorithm (GA). The proposed design technique allows considerable flexibility in defining the control objectives and it does not consider any knowledge of the system matrices and moreover it avoids the solution of algebraic Riccati equation. To illustrate the results of this work, a load-frequency control problem is considered. Simulation results reveal that the proposed scheme based on GA is an alternative and attractive approach to solve load-frequency control problem from both performance and design point of views.

  3. ICE: A Scalable, Low-Cost FPGA-Based Telescope Signal Processing and Networking System

    Science.gov (United States)

    Bandura, K.; Bender, A. N.; Cliche, J. F.; de Haan, T.; Dobbs, M. A.; Gilbert, A. J.; Griffin, S.; Hsyu, G.; Ittah, D.; Parra, J. Mena; Montgomery, J.; Pinsonneault-Marotte, T.; Siegel, S.; Smecher, G.; Tang, Q. Y.; Vanderlinde, K.; Whitehorn, N.

    We present an overview of the ‘ICE’ hardware and software framework that implements large arrays of interconnected field-programmable gate array (FPGA)-based data acquisition, signal processing and networking nodes economically. The system was conceived for application to radio, millimeter and sub-millimeter telescope readout systems that have requirements beyond typical off-the-shelf processing systems, such as careful control of interference signals produced by the digital electronics, and clocking of all elements in the system from a single precise observatory-derived oscillator. A new generation of telescopes operating at these frequency bands and designed with a vastly increased emphasis on digital signal processing to support their detector multiplexing technology or high-bandwidth correlators — data rates exceeding a terabyte per second — are becoming common. The ICE system is built around a custom FPGA motherboard that makes use of an Xilinx Kintex-7 FPGA and ARM-based co-processor. The system is specialized for specific applications through software, firmware and custom mezzanine daughter boards that interface to the FPGA through the industry-standard FPGA mezzanine card (FMC) specifications. For high density applications, the motherboards are packaged in 16-slot crates with ICE backplanes that implement a low-cost passive full-mesh network between the motherboards in a crate, allow high bandwidth interconnection between crates and enable data offload to a computer cluster. A Python-based control software library automatically detects and operates the hardware in the array. Examples of specific telescope applications of the ICE framework are presented, namely the frequency-multiplexed bolometer readout systems used for the South Pole Telescope (SPT) and Simons Array and the digitizer, F-engine, and networking engine for the Canadian Hydrogen Intensity Mapping Experiment (CHIME) and Hydrogen Intensity and Real-time Analysis eXperiment (HIRAX

  4. Control volume based hydrocephalus research

    Science.gov (United States)

    Cohen, Benjamin; Voorhees, Abram; Wei, Timothy

    2008-11-01

    Hydrocephalus is a disease involving excess amounts of cerebral spinal fluid (CSF) in the brain. Recent research has shown correlations to pulsatility of blood flow through the brain. However, the problem to date has presented as too complex for much more than statistical analysis and understanding. This talk will highlight progress on developing a fundamental control volume approach to studying hydrocephalus. The specific goals are to select physiologically control volume(s), develop conservation equations along with the experimental capabilities to accurately quantify terms in those equations. To this end, an in vitro phantom is used as a simplified model of the human brain. The phantom's design consists of a rigid container filled with a compressible gel. The gel has a hollow spherical cavity representing a ventricle and a cylindrical passage representing the aquaducts. A computer controlled piston pump supplies pulsatile volume fluctuations into and out of the flow phantom. MRI is used to measure fluid velocity, and volume change as functions of time. Independent pressure measurements and flow rate measurements are used to calibrate the MRI data. These data are used as a framework for future work with live patients.

  5. Model based development of engine control algorithms

    NARCIS (Netherlands)

    Dekker, H.J.; Sturm, W.L.

    1996-01-01

    Model based development of engine control systems has several advantages. The development time and costs are strongly reduced because much of the development and optimization work is carried out by simulating both engine and control system. After optimizing the control algorithm it can be executed b

  6. Budgeting-Based Organization of Internal Control

    Science.gov (United States)

    Rogulenko, Tatiana; Ponomareva, Svetlana; Bodiaco, Anna; Mironenko, Valentina; Zelenov, Vladimir

    2016-01-01

    The article suggests methodical approaches to the budgeting-based organization of internal control, determines the tasks and subtasks of control that consist in the construction of an efficient system for the making, implementation, control, and analysis of managerial decisions. The organization of responsibility centers by means of implementing…

  7. Dos momentos de duda ante la muerte: los poemas de Sócrates y la última pregunta de Jesús

    Directory of Open Access Journals (Sweden)

    Sergio Andrés Sandoval

    2011-01-01

    Full Text Available Según George Steiner, los dos grandes maestros de la cultura occidental, cuyas muertes han sido ejecuciones ordenadas lue - go de ser juzgados, han dado origen a diversos textos que son fundamentales en el pensamiento y en el arte. Así mismo, ante la cercanía de la muerte tanto Jesús como Sócrates han dudado de profundas convicciones argumentadas en sus discursos. De esta manera, el ęlósofo griego escribe poesía en el Fedón de Platón y el ho de Dios le pregunta a su padre por su abandono en los Evan - gelios de Mateo y Marcos.

  8. Ricoeur y la explicitacíon ontológica del postulado de la referencia. El ejemplo de Sócrates, filósofo y poeta

    OpenAIRE

    Castro, Maria Gabriela

    2006-01-01

    Platón presenta a Sócrates en el Fedón escribiendo poemas. (Cómo puede ser esta posible en el contexto de su pensamiento? Esta es la pregunta que está en el origen del presente artículo. Releemos a Platón, analizando el Fedón con la ayuda de la filosofía de Paul Ricoeur. Procedemos a través de la intersección de los conceptos de metáfora y poiesis, con el objeto de descubrir la génesis del discurso poético y argumentativo. El asunto central que explora este estudio es el problema de la refere...

  9. Notas heréticas sobre lógica y sofística en la “Apología de Sócrates

    OpenAIRE

    Vélasco, Sírio Lopez

    2016-01-01

    En este trabajo sometemos a análisis crítico (desde el punto de vista de la lógica y del rechazo a la sofística)  la conducta y discurso  del maestro Platón en la obra destinada a perpetuar su gloriosa memoria: la “Apología de Sócrates”. Veremos que en su autodefensa Sócrates incurre en equívocos lógicos y usa diversos recursos de tipo sofístico (que bien hubieran podido servir a su principal acusador, Meleto). Así nuestra lectura humaniza al personaje y contribuye a hacer menos clara la neta...

  10. Fuzzy Based composition Control of Distillation Column

    Directory of Open Access Journals (Sweden)

    Guru.R

    2013-04-01

    Full Text Available This paper proposed a control scheme based on fuzzy logic for a methanol - water system of bubble cap distillation column. Fuzzy rule base and Inference System of fuzzy (FIS is planned to regulatethe reflux ratio (manipulated variable to obtain the preferred product composition (methanol for a distillation column. Comparisons are made with conventional controller and the results confirmed the potentials of the proposed strategy of fuzzy control.

  11. Exporting Variables in a Hierarchically Distributed Control System

    Energy Technology Data Exchange (ETDEWEB)

    Chamizo Llatas, M.

    1995-07-01

    We describe the Remote Variable Access Service (RVAS), a network service developed and used in the distributed control and monitoring system of the TJ-II Heliac, which is under construction at CIEMAT (Madrid, Spain) and devoted to plasma studies in the nuclear fusion field. The architecture of the TJ-II control system consists of one central Sun workstation Sparc 10 and several autonomous subsystems based on VME crates with embedded processors running the OS-9 (V.24) real time operating system. The RVAS service allows state variables in local control processes running in subsystems to be exported to remote processes running in the central control workstation. Thus we extend the concept of exporting of file systems in UNIX machines to variables in processes running in different machines. (Author) 6 refs.

  12. Computer control for the CERN ISOLDE-3 project

    Science.gov (United States)

    Lustig, H. D.; Benincasa, G. P.; Richard-Serre, C.

    1987-05-01

    ISOLDE-3 has been designed for fully integrated computer control from the beginning. Budget and manpower limitations required that we should use already existing CERN equipment to a large extent, both on the hardware and software side. A CAMAC integrated, multi-microprocessor computer system (based on the Motorola 68000) with serial CAMAC transmission has been chosen. To ease programming by nonspecialists the interpretive language NODAL is extensively used. The control system has three consoles, each one driven by a "mother crate" containing the microprocessors, the modules for the user interactions and the peripherals. For the time being there are no links between the 3 single-user, single-task systems. The criteria for the distribution of the various tasks are therefore to put in the same loop only systems which do not need simultaneous control. Particular emphasis was put on standardisation: all similar elements are controlled by the same hardware modules and standard software packages allow easy modifications and extensions.

  13. Effect of variability in lighting and temperature environments for mature gilts housed in gestation crates on measures of reproduction and animal well-being.

    Science.gov (United States)

    Canaday, D C; Salak-Johnson, J L; Visconti, A M; Wang, X; Bhalerao, K; Knox, R V

    2013-03-01

    The effects of room temperature and light intensity before breeding and into early gestation were evaluated on the reproductive performance and well-being of gilts housed individually in crates. In eight replicates, estrus was synchronized in mature gilts (n = 198) and after last feeding of Matrix were randomly assigned to a room temperature of 15°C (COLD), 21°C (NEUTRAL), or 30°C (HOT) and a light intensity of 11 (DIM) or 433 (BRIGHT) lx. Estrous detection was performed daily and gilts inseminated twice. Blood samples were collected before and after breeding for determination of immune measures and cortisol concentrations. Gilt ADFI, BW, and body temperature were measured. On d 30 postbreeding, gilts were slaughtered to recover reproductive tracts to evaluate pregnancy and litter characteristics. There were no temperature × light intensity interactions for any response variable. Reproductive measures of follicle development, expression of estrus, ovulation rate, pregnancy rate (83.2%), litter size (14.3 ± 0.5), and fetal measures were not affected by temperature or lighting (P > 0.10). Gilts in COLD (37.6°C) had a lower (P 0.10) of light or interaction with temperature on other immune cells or measures. These results indicate that temperatures in the range of 15 to 30°C or light intensity at 11 to 433 lx do not impact reproduction during the follicular phase and into early gestation for mature gilts housed in gestation crates. However, room temperature does impact physiological, behavioral, and immune responses of mature gilts and should be considered as a potential factor that may influence gilt well-being during the first 30 d postbreeding.

  14. Analytical protocol to study the food safety of (multiple-)recycled high-density polyethylene (HDPE) and polypropylene (PP) crates: Influence of recycling on the migration and formation of degradation products

    NARCIS (Netherlands)

    Coulier, L.; Orbons, H.G.M.; Rijk, R.

    2007-01-01

    An analytical protocol was set up and successfully applied to study the food safety of recycled HDPE and PP crates. A worst-case scenario was applied that focused not only on overall migration and specific migration of accepted starting materials but also on migratable degradation products of polyme

  15. Linearizing Control of Induction Motor Based on Networked Control Systems

    Institute of Scientific and Technical Information of China (English)

    Jun Ren; Chun-Wen Li; De-Zong Zhao

    2009-01-01

    A new approach to speed control of induction motors is developed by introducing networked control systems (NCSs) into the induction motor driving system. The control strategy is to stabilize and track the rotor speed of the induction motor when the network time delay occurs in the transport medium of network data. First, a feedback linearization method is used to achieve input-output linearization and decoupling control of the induction motor driving system based on rotor flux model, and then the characteristic of network data is analyzed in terms of the inherent network time delay. A networked control model of an induction motor is established. The sufficient condition of asymptotic stability for the networked induction motor driving system is given, and the state feedback controller is obtained by solving the linear matrix inequalities (LMIs). Simulation results verify the efficiency of the proposed scheme.

  16. Model-Based Power Plant Master Control

    Energy Technology Data Exchange (ETDEWEB)

    Boman, Katarina; Thomas, Jean; Funkquist, Jonas

    2010-08-15

    The main goal of the project has been to evaluate the potential of a coordinated master control for a solid fuel power plant in terms of tracking capability, stability and robustness. The control strategy has been model-based predictive control (MPC) and the plant used in the case study has been the Vattenfall power plant Idbaecken in Nykoeping. A dynamic plant model based on nonlinear physical models was used to imitate the true plant in MATLAB/SIMULINK simulations. The basis for this model was already developed in previous Vattenfall internal projects, along with a simulation model of the existing control implementation with traditional PID controllers. The existing PID control is used as a reference performance, and it has been thoroughly studied and tuned in these previous Vattenfall internal projects. A turbine model was developed with characteristics based on the results of steady-state simulations of the plant using the software EBSILON. Using the derived model as a representative for the actual process, an MPC control strategy was developed using linearization and gain-scheduling. The control signal constraints (rate of change) and constraints on outputs were implemented to comply with plant constraints. After tuning the MPC control parameters, a number of simulation scenarios were performed to compare the MPC strategy with the existing PID control structure. The simulation scenarios also included cases highlighting the robustness properties of the MPC strategy. From the study, the main conclusions are: - The proposed Master MPC controller shows excellent set-point tracking performance even though the plant has strong interactions and non-linearity, and the controls and their rate of change are bounded. - The proposed Master MPC controller is robust, stable in the presence of disturbances and parameter variations. Even though the current study only considered a very small number of the possible disturbances and modelling errors, the considered cases are

  17. Smith Predictor Based Robust Rapid Tracking Controller

    Institute of Scientific and Technical Information of China (English)

    LIU Hongbin; HU Dejin

    2006-01-01

    Precise model is hard to get in real application, a Smith predictor based robust rapid tracking controller for inaccurate model is proposed. Zero phase error feedforward controller which increases system closed-loop dynamics and disturbance observer based Smith feedback control which diminishes model hysteresis and improves stability are integrated. This method is applied in the noncircular machining with piezoelectric ceramic driver. The simulation and experiment show that the performance robustness and stability are well balanced in bandwidth about 200 Hz. The controller can decrease system hysteresis and get good tracking performance for predefined square-wave input signal.

  18. ROBUST INTERNAL MODEL CONTROL STRATEGY BASED PID CONTROLLER FOR BLDCM

    Directory of Open Access Journals (Sweden)

    A.PURNA CHANDRA RAO

    2010-11-01

    Full Text Available All the closed loop control system requires the controller for improvement of transient response of the error signal. Though the tuning of PID controller in real time is bit difficult and moreover it lacks the disturbance rejection capability. This paper presents a tuning of PID parameters based on internal model strategy. The advantageous of the proposed control strategy is well described in the paper. To test the validity of the proposed control, it is implemented in brushless dc motor drive. The mathematical model of brushless dc motor (BLDC is presented for control design. In addition the robustness of the control strategy is discussed. The proposed control strategy possesses good transient responses and good load disturbance response. In addition, the proposed control strategy possesses good tracking ability. To test the effectiveness of the proposed strategy, the BLDC is represented in transfer function model and later implemented in test system. The results are presented to validate the proposed control strategy for BLDC drive.

  19. Summary of The 3rd Control System Cyber-Security (CS)2/HEP Workshop

    CERN Document Server

    Lüders, S

    2011-01-01

    Over the last decade modern accelerator and experiment control systems have increasingly been based on commercial-off-the-shelf products (VME crates, programmable logic controllers (PLCs), supervisory control and data acquisition (SCADA) systems, etc.), on Windows or Linux PCs, and on communication infrastructures using Ethernet and TCP/IP. Despite the benefits coming with this (r)evolution, new vulnerabilities are inherited, too: Worms and viruses spread within seconds via the Ethernet cable, and attackers are becoming interested in control systems. The Stuxnet worm of 2010 against a particular Siemens PLC is a unique example for a sophisticated attack against control systems [1]. Unfortunately, control PCs cannot be patched as fast as office PCs. Even worse, vulnerability scans at CERN using standard IT tools have shown that commercial automation systems lack fundamental security precautions: Some systems crashed during the scan, others could easily be stopped or their process data being ...

  20. Control of acrobot based on Lyapunov function

    Institute of Scientific and Technical Information of China (English)

    赖旭芝; 吴敏; 佘锦华

    2004-01-01

    Fuzzy control based on Lyapunov function was employed to control the posture and the energy of an acrobot to make the transition from upswing control to balance control smoothly and stably. First, a control law based on Lyapunov function was used to control the angle and the angular velocity of the second link towards zero when the energy of the acrobot reaches the potential energy at the unstable straight-up equilibrium position in the upswing process. The controller based on Lyapunov function makes the second link straighten nature relatively to the first link. At the same time, a fuzzy controller was designed to regulate the parameters of the upper control law to keep the change of the energy of the acrobot to a minimum, so that the switching from upswing to balance can be properly carried out and the acrobot can enter the balance quickly. The results of simulation show that the switching from upswing to balance can be completed smoothly, and the control effect of the acrobot is improved greatly.

  1. Model-based control of networked systems

    CERN Document Server

    Garcia, Eloy; Montestruque, Luis A

    2014-01-01

    This monograph introduces a class of networked control systems (NCS) called model-based networked control systems (MB-NCS) and presents various architectures and control strategies designed to improve the performance of NCS. The overall performance of NCS considers the appropriate use of network resources, particularly network bandwidth, in conjunction with the desired response of the system being controlled.   The book begins with a detailed description of the basic MB-NCS architecture that provides stability conditions in terms of state feedback updates . It also covers typical problems in NCS such as network delays, network scheduling, and data quantization, as well as more general control problems such as output feedback control, nonlinear systems stabilization, and tracking control.   Key features and topics include: Time-triggered and event-triggered feedback updates Stabilization of uncertain systems subject to time delays, quantization, and extended absence of feedback Optimal control analysis and ...

  2. A mobile console for local access to accelerator control systems.

    CERN Multimedia

    1981-01-01

    Microprocessors were installed as auxiliary crate controllers (ACCs) in the CAMAC interface of control systems for various accelerators. The same ACC was also at the hearth of a stand-alone system in the form of a mobile console. This was also used for local access to the control systems for tests and development work (Annual Report 1981, p. 80, Fig. 10).

  3. SPOT Controlled Image Base 10 meter

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — SPOT Controlled Image Base 10 meter (CIB-10) is a collection of orthorectified panchromatic (grayscale) images. The data were acquired between 1986 and 1993 by the...

  4. SPOT Controlled Image Base 10 meter

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — SPOT Controlled Image Base 10 meter (CIB-10) is a collection of orthorectified panchromatic (grayscale) images. The data were acquired between 1986 and 1993 by the...

  5. Implementation of PLC Based Elevator Control System

    Directory of Open Access Journals (Sweden)

    Sandar Htay

    2014-03-01

    Full Text Available This paper describes programmable logic controller based elevator control system. An elevator is one of the important aspects in electronics control module in automotive application. Nowadays, Myanmar is a developing country and there is enormous increase in high-rise building in Myanmar. This paper mainly focuses on using programmable logic controller to control the circuit and building the elevator model. Hall Effect sensor is used for the elevator position. DC Motor is used to control the up and down movement of the elevator car. Push buttons are used to call the elevator car. The elevator position is described by using the display unit. In this paper, Auto Station Software ladder logic program is used for four floors control system

  6. Vector Control Based on SVPWM for ACIM

    Directory of Open Access Journals (Sweden)

    Zhu Jun

    2013-05-01

    Full Text Available To solve the large torque ripple and current harmonics, low DC bus voltage problems, a new control strategy is proposed for AC induction motor by using space vector pulse width modulation, so that the static and dynamic performance are improved. The system simulation experiment mode was established based on SVPWM to verify the effectiveness of the system control mode. It is showed that it can reduce the current ripple and torque ripple, improve the utilization of DC bus voltage. It means that the control strategy based SVPWM can improve dynamic and static performance effectively for the ACIM servo system.

  7. Model based control charts in stage 1 quality control

    NARCIS (Netherlands)

    A.J. Koning (Alex)

    1999-01-01

    textabstractIn this paper a general method of constructing control charts for preliminary analysis of individual observations is presented, which is based on recursive score residuals. A simulation study shows that certain implementations of these charts are highly effective in detecting assignable

  8. Version Control in Project-Based Learning

    Science.gov (United States)

    Milentijevic, Ivan; Ciric, Vladimir; Vojinovic, Oliver

    2008-01-01

    This paper deals with the development of a generalized model for version control systems application as a support in a range of project-based learning methods. The model is given as UML sequence diagram and described in detail. The proposed model encompasses a wide range of different project-based learning approaches by assigning a supervisory…

  9. Passivity-Based Control of Electric Machines

    Energy Technology Data Exchange (ETDEWEB)

    Nicklasson, P.J.

    1996-12-31

    This doctoral thesis presents new results on the design and analysis of controllers for a class of electric machines. Nonlinear controllers are derived from a Lagrangian model representation using passivity techniques, and previous results on induction motors are improved and extended to Blondel-Park transformable machines. The relation to conventional techniques is discussed, and it is shown that the formalism introduced in this work facilitates analysis of conventional methods, so that open questions concerning these methods may be resolved. In addition, the thesis contains the following improvements of previously published results on the control of induction motors: (1) Improvement of a passivity-based speed/position controller, (2) Extension of passivity-based (observer-less and observer-based) controllers from regulation to tracking of rotor flux norm, (3) An extension of the classical indirect FOC (Field-Oriented Control) scheme to also include global rotor flux norm tracking, instead of only torque tracking and rotor flux norm regulation. The design is illustrated experimentally by applying the proposed control schemes to a squirrel-cage induction motor. The results show that the proposed methods have advantages over previous designs with respect to controller tuning, performance and robustness. 145 refs., 21 figs.

  10. GUI Application for ATCA-based LLRF Carrier Board Management

    CERN Document Server

    Wychowaniak, Jan; Predki, Pawel; Napieralski, Andrzej

    2011-01-01

    The Advanced Telecommunications Computing Architecture (ATCA) standard describes an efficient and powerful platform, implementation of which was adopted to be used as a base for control systems in high energy physics. The ATCA platform is considered to be applied for the X-ray Free Electron Laser (X-FEL), being built at Deutsches Electronen- Synchrotron (DESY) in Hamburg, Germany. The Low Level Radio Frequency (LLRF) control system is composed of a few ATCA Carrier Boards. Carrier Board hosts Intelligent Platform Management Controller (IPMC), which is developed in compliance with the PICMG specifications. IPMC is responsible for management and monitoring of sub-modules installed on Carrier Boards and pluggable Advanced Mezzanine Card (AMC) modules. The ATCA Shelf Manager is the main control unit of a single ATCA crate, responsible for all power and fan modules and Carrier Boards installed in ATCA shelf. The device provides a system administrator with a set of control and diagnostic capabilities regarding the ...

  11. Development of Arduino based wireless control system

    Science.gov (United States)

    Sun, Zhuoxiong; Dyke, Shirley J.; Pena, Francisco; Wilbee, Alana

    2015-03-01

    Over the past few decades, considerable attention has been given to structural control systems to mitigate structural vibration under natural hazards such as earthquakes and extreme weather conditions. Traditional wired structural control systems often employ a large amount of cables for communication among sensors, controllers and actuators. In such systems, implementation of wired sensors is usually quite complicated and expensive, especially on large scale structures such as bridges and buildings. To reduce the laborious installation and maintenance cost, wireless control systems (WCSs) are considered as a novel approach for structural vibration control. In this work, a WCS is developed based on the open source Arduino platform. Low cost, low power wireless sensing and communication components are built on the Arduino platform. Structural control algorithms are embedded within the wireless sensor board for feedback control. The developed WCS is first validated through a series of tests. Next, numerical simulations are performed simulating wireless control of a 3-story shear structure equipped with a semi-active control device (MR damper). Finally, experimental studies are carried out implementing the WCS on the 3-story shear structure in the Intelligent Infrastructure Systems Lab (IISL). A hydraulic shake table is used to generate seismic ground motions. The control performance is evaluated with the impact of modeling uncertainties, measurement noises as well as time delay and data loss induced by the wireless network. The developed WCS is shown to be effective in controlling structural vibrations under several historical earthquake ground motions.

  12. FIPA agent based network distributed control system

    CERN Document Server

    Gyurjyan, V; Heyes, G; Jastrzembski, E; Timmer, C; Wolin, E

    2003-01-01

    A control system with the capabilities to combine heteregeneous control systems or processes into a uniform homogeneous environment is discussed. This dynamically extensible system is an example of the software system at the agent level of abstraction. This level of abstraction considers agents as atomic entities that communicate to implement the functionality of the control system. Agents engineering aspects are addressed by adopting the domain independent software standard, formulated by FIPA. Jade core Java classes are used as a FIPA specification implementation. A special, lightweight, XML RDFS based, control oriented, ontology markup language is developed to standardize the description of the arbitrary control system data processor. Control processes, described in this language, are integrated into the global system at runtime, without actual programming. Fault tolerance and recovery issues are also addressed.

  13. FIPA agent based network distributed control system

    Energy Technology Data Exchange (ETDEWEB)

    D. Abbott; V. Gyurjyan; G. Heyes; E. Jastrzembski; C. Timmer; E. Wolin

    2003-03-01

    A control system with the capabilities to combine heterogeneous control systems or processes into a uniform homogeneous environment is discussed. This dynamically extensible system is an example of the software system at the agent level of abstraction. This level of abstraction considers agents as atomic entities that communicate to implement the functionality of the control system. Agents' engineering aspects are addressed by adopting the domain independent software standard, formulated by FIPA. Jade core Java classes are used as a FIPA specification implementation. A special, lightweight, XML RDFS based, control oriented, ontology markup language is developed to standardize the description of the arbitrary control system data processor. Control processes, described in this language, are integrated into the global system at runtime, without actual programming. Fault tolerance and recovery issues are also addressed.

  14. Cluster-based control of nonlinear dynamics

    CERN Document Server

    Kaiser, Eurika; Spohn, Andreas; Cattafesta, Louis N; Morzynski, Marek

    2016-01-01

    The ability to manipulate and control fluid flows is of great importance in many scientific and engineering applications. Here, a cluster-based control framework is proposed to determine optimal control laws with respect to a cost function for unsteady flows. The proposed methodology frames high-dimensional, nonlinear dynamics into low-dimensional, probabilistic, linear dynamics which considerably simplifies the optimal control problem while preserving nonlinear actuation mechanisms. The data-driven approach builds upon a state space discretization using a clustering algorithm which groups kinematically similar flow states into a low number of clusters. The temporal evolution of the probability distribution on this set of clusters is then described by a Markov model. The Markov model can be used as predictor for the ergodic probability distribution for a particular control law. This probability distribution approximates the long-term behavior of the original system on which basis the optimal control law is de...

  15. Natural ventilation and surface temperature distribution of piglet crate heated floors Ventilação natural e temperatura da superfície de pisos aquecidos em escamoteadores

    Directory of Open Access Journals (Sweden)

    A.S. Mendes

    2013-04-01

    Full Text Available This research had the objective of evaluating the influence of the natural ventilation on the surface temperature distribution of heated crates. The research used six crates from a farrowing room in a commercial swine production farm located in the state of São Paulo, Brazil. Three crates were heated using a heat mat while the other three had the environment heated by incandescent light bulbs (200W fixed on the lateral wall. The surface temperature of the crate's floor (1.55x0.55m was registered in 36 points, distributed in 18 quadrants (0.26x0.18m using an infrared thermometer in three different conditions of the room's natural ventilation: opened, semi-opened, and closed lateral curtain. The isotherms and the temperature distribution of the floor heat were processed using the SURFER® (1995, and the statistical analysis was done using the MINITAB® (Statistical..., 2002. It was found that the room's natural ventilation had a significant influence on crate floor surface temperature distribution. The crate with a heat mat system provided higher temperatures and led to a more homogeneous surface temperature distribution.O objetivo deste trabalho foi avaliar a influência da ventilação natural sobre a distribuição da temperatura na superfície de pisos aquecidos em escamoteadores. Foram avaliados seis escamoteadores da maternidade de uma granja de suínos localizada no estado de São Paulo. Dentre os escamoteadores avaliados, três deles usavam piso aquecido para o acondicionamento dos leitões, e os outros usavam lâmpadas incandescentes (200W, fixadas na parede lateral do interior do escamoteador. A temperatura da superfície do piso (1,55x0,55m foi registrada medindo-se 36 pontos distribuídos em 18 quadrantes (0,26x0,18m, por meio de um termômetro infravermelho, em três diferentes condições de ventilação natural: com cortina lateral aberta, semiaberta e totalmente fechada. As isotermas e a distribuição da temperatura sobre o piso

  16. Model Based Adaptive Piecewise Linear Controller for Complicated Control Systems

    Directory of Open Access Journals (Sweden)

    Tain-Sou Tsay

    2014-01-01

    Full Text Available A model based adaptive piecewise linear control scheme for industry processes with specifications on peak overshoots and rise times is proposed. It is a gain stabilized control technique. Large gain is used for large tracking error to get fast response. Small gain is used between large and small tracking error for good performance. Large gain is used again for small tracking error to cope with large disturbance. Parameters of the three-segment piecewise linear controller are found by an automatic regulating time series which is function of output characteristics of the plant and reference model. The time series will be converged to steady values after the time response of the considered system matching that of the reference model. The proposed control scheme is applied to four numerical examples which have been compensated by PID controllers. Parameters of PID controllers are found by optimization method. It gives an almost command independent response and gives significant improvements for response time and performance.

  17. Flocculation control study based on fractal theory

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    A study on flocculation control based on fractal theory was carried out. Optimization test of chemical coagulant dosage confirmed that the fractal dimension could reflect the flocculation degree and settling characteristics of aggregates and the good correlation with the turbidity of settled effluent. So that the fractal dimension can be used as the major parameter for flocculation system control and achieve self-acting adjustment of chemical coagulant dosage. The fractal dimension flocculation control system was used for further study carried out on the effects of various flocculation parameters, among which are the dependency relationship among aggregates fractal dimension, chemical coagulant dosage, and turbidity of settled effluent under the conditions of variable water quality and quantity. And basic experimental data were obtained for establishing the chemical coagulant dosage control model mainly based on aggregates fractal dimension.

  18. Optimization-based controller design for rotorcraft

    Science.gov (United States)

    Tsing, N.-K.; Fan, M. K. H.; Barlow, J.; Tits, A. L.; Tischler, M. B.

    1993-01-01

    An optimization-based methodology for linear control system design is outlined by considering the design of a controller for a UH-60 rotorcraft in hover. A wide range of design specifications is taken into account: internal stability, decoupling between longitudinal and lateral motions, handling qualities, and rejection of windgusts. These specifications are investigated while taking into account physical limitations in the swashplate displacements and rates of displacement. The methodology crucially relies on user-machine interaction for tradeoff exploration.

  19. Polarization control based interference microwave photonic filters

    Science.gov (United States)

    Madziar, Krzysztof; Galwas, Bogdan

    2016-12-01

    In this paper we present a concept of multi-line Microwave Photonic Filter (MPF) based on polarization beam splitting and polarization control in each line. Coefficients of investigated filter are determined by attenuation of its lines and that on the other hand can be manipulated by change of the polarization in the fiber. Presented results involve scattering parameters (S21) measurements of optical path over polarization control unit rotation, scattering parameters (S21) characteristics of investigated filter and transmission optimization capabilities.

  20. Performance of Object-Oriented Real-Time Control and Acquisition Software

    Science.gov (United States)

    Collins, Andrew

    2010-11-01

    The dead-time of the Object-oriented Real-time Control and Aqcuisition data acquisition software, orca, was quantitatively determined for a VME-based system utilizing a single, peak-sensing CAEN 785N analog-to-digital converter and two scaler modules. A single board computer in the VME crate controls rapid read-out of the modules and the data is then transferred via TCP/IP to the orca control program, running on MacOSX, where the data can be filtered based on desired criteria, saved in an open format, and displayed on-line in histograms. A graphical interface allows the system to be configured via ``drag and drop'' method. The performance tests were performed on orca and two other data acquisition systems used at Triangle Universities Nuclear Laboratory, coda and SpecTcl, to compare the systems' data collection capabilities and determine whether the new system is a worthy competitor of the existing systems.

  1. Developing stereo image based robot control system

    Science.gov (United States)

    Suprijadi, Pambudi, I. R.; Woran, M.; Naa, C. F.; Srigutomo, W.

    2015-04-01

    Application of image processing is developed in various field and purposes. In the last decade, image based system increase rapidly with the increasing of hardware and microprocessor performance. Many fields of science and technology were used this methods especially in medicine and instrumentation. New technique on stereovision to give a 3-dimension image or movie is very interesting, but not many applications in control system. Stereo image has pixel disparity information that is not existed in single image. In this research, we proposed a new method in wheel robot control system using stereovision. The result shows robot automatically moves based on stereovision captures.

  2. Logic and logic-based control

    Institute of Scientific and Technical Information of China (English)

    Hongsheng QI; Daizhan CHENG

    2008-01-01

    This paper gives a matrix expression of logic. Under the matrix expression, a general description of the logical operators is proposed. Using the semi-tensor product of matrices, the proofs of logical equivalences, implications, etc., can be simplified a lot. Certain general properties are revealed. Then, based on matrix expression, the logical operators are extended to multi-valued logic, which provides a foundation for fuzzy logical inference. Finally, we propose a new type of logic, called mix-valued logic, and a new design technique, called logic-based fuzzy control. They provide a numerically computable framework for the application of fuzzy logic for the control of fuzzy systems.

  3. Developing stereo image based robot control system

    Energy Technology Data Exchange (ETDEWEB)

    Suprijadi,; Pambudi, I. R.; Woran, M.; Naa, C. F; Srigutomo, W. [Department of Physics, FMIPA, InstitutTeknologi Bandung Jl. Ganesha No. 10. Bandung 40132, Indonesia supri@fi.itb.ac.id (Indonesia)

    2015-04-16

    Application of image processing is developed in various field and purposes. In the last decade, image based system increase rapidly with the increasing of hardware and microprocessor performance. Many fields of science and technology were used this methods especially in medicine and instrumentation. New technique on stereovision to give a 3-dimension image or movie is very interesting, but not many applications in control system. Stereo image has pixel disparity information that is not existed in single image. In this research, we proposed a new method in wheel robot control system using stereovision. The result shows robot automatically moves based on stereovision captures.

  4. Model Based Control of Reefer Container Systems

    DEFF Research Database (Denmark)

    Sørensen, Kresten Kjær

    This thesis is concerned with the development of model based control for the Star Cool refrigerated container (reefer) with the objective of reducing energy consumption. This project has been carried out under the Danish Industrial PhD programme and has been financed by Lodam together with the Da......This thesis is concerned with the development of model based control for the Star Cool refrigerated container (reefer) with the objective of reducing energy consumption. This project has been carried out under the Danish Industrial PhD programme and has been financed by Lodam together...

  5. Microcontroller-based Feedback Control Laboratory Experiments

    Directory of Open Access Journals (Sweden)

    Chiu Choi

    2014-06-01

    Full Text Available this paper is a result of the implementation of the recommendations on enhancing hands-on experience of control engineering education using single chip, small scale computers such as microcontrollers. A set of microcontroller-based feedback control experiments was developed for the Electrical Engineering curriculum at the University of North Florida. These experiments provided hands-on techniques that students can utilize in the development of complete solutions for a number of servo control problems. Significant effort was devoted to software development of feedback controllers and the associated signal conditioning circuits interfacing between the microcontroller and the physical plant. These experiments have stimulated the interest of our students in control engineering.

  6. Problems in event based engine control

    DEFF Research Database (Denmark)

    Hendricks, Elbert; Jensen, Michael; Chevalier, Alain Marie Roger

    1994-01-01

    Physically a four cycle spark ignition engine operates on the basis of four engine processes or events: intake, compression, ignition (or expansion) and exhaust. These events each occupy approximately 180° of crank angle. In conventional engine controllers, it is an accepted practice to sample...... the engine variables synchronously with these events (or submultiples of them). Such engine controllers are often called event-based systems. Unfortunately the main system noise (or disturbance) is also synchronous with the engine events: the engine pumping fluctuations. Since many electronic engine...... problems on accurate air/fuel ratio control of a spark ignition (SI) engine....

  7. Installation and Operation of RENO Slow Control and Online Monitoring System

    CERN Document Server

    Choi, J H; Pac, M Y; Ahn, J K; Choi, S; Choi, Y; Choi, W K; Jang, J S; Jeon, E J; Joo, K K; Kim, H S; Kim, J Y; Kim, S B; Kim, W; Kim, Y D; Lee, J; Lim, I T; Ma, K J; Park, I G; Park, J S; Park, K S; Shin, J W; K, Siyeon; Stepanyan, S S; Yeo, I S; Yu, I

    2013-01-01

    The RENO is the reactor based experiment to measure the smallest neutrino mixing angle, $\\theta_{13}$. The slow control and online monitoring system for RENO monitors the status of the HV systems, the temperatures of the electronics crates and detectors, the fluids levels, humidities of experimental halls and electronics huts, and gas concentrations. And the slow control system is able to set up high voltage for each channel and turn on and off HV remotely. An online monitoring system located in the control room reads data from the DAQ host computer via network. It provides event display, online histograms to monitor detector performance, and variety of additional tasks needed to efficiently monitor detector performance parameters and diagnose troubles of detector and DAQ system. In this paper, we explan the installation of the slow control and monitoring system and their operation status,

  8. Update on the CERN Computing and Network Infrastructure for Controls (CNIC)

    CERN Multimedia

    Lueders, S

    2007-01-01

    Over the last few years modern accelerator and experiment control systems have increasingly been based on commercial-off-the-shelf products (VME crates, PLCs, SCADA systems, etc.), on Windows or Linux PCs, and on communication infrastructures using Ethernet and TCP/IP. Despite the benefits coming with this (r)evolution, new vulnerabilities are inherited too: Worms and viruses spread within seconds via the Ethernet cable, and attackers are becoming interested in control systems. Unfortunately, control PCs cannot be patched as fast as office PCs. Even worse, vulnerability scans at CERN using standard IT tools have shown that commercial automation systems lack fundamental security precautions: Some systems crashed during the scan, others could easily be stopped or their process data be altered. During the two years following the presentation of the CNIC Security Policy at ICALEPCS2005, a "Defense-in-Depth" approach has been applied to protect CERN's control systems. This presentation will give a review of its th...

  9. Summary of the Control System Cyber-Security (CS)2/HEP Workshop

    CERN Document Server

    Lüders, S

    2007-01-01

    Over the last few years modern accelerator and experiment control systems have increasingly been based on commercial-off-the-shelf products (VME crates, PLCs, SCADA systems, etc.), on Windows or Linux PCs, and on communication infrastructures using Ethernet and TCP/IP. Despite the benefits coming with this (r)evolution, new vulnerabilities are inherited, too: Worms and viruses spread within seconds via the Ethernet cable, and attackers are becoming interested in control systems. Unfortunately, control PCs cannot be patched as fast as office PCs. Even worse, vulnerability scans at CERN using standard IT tools have shown that commercial automation systems lack fundamental security precautions: Some systems crashed during the scan, others could easily be stopped or their process data be altered. The (CS)2/HEP workshop held the weekend before ICALEPCS2007 was intended to present, share, and discuss countermeasures deployed in HEP laboratories in order to secure control systems. This presentation will give a summa...

  10. Hidroquímica do carbonato e bicarbonato: efeito na qualidade de águas subterrâneas em Crateús, Ceará, Brasil

    Directory of Open Access Journals (Sweden)

    José Ossian Gadelha de Lima

    2014-07-01

    Full Text Available O município de Crateús está localizado na região semiárida do Nordeste do Brasil, onde as condições climáticas provocam escassez hídrica e baixa qualidade nas águas disponíveis. Este trabalho teve por objetivo estudar, durante um ano, o comportamento do pH e das concentrações dos íons carbonato (CO3 2- e bicarbonato (HCO3 - nas águas de oito poços utilizadas para irrigação de pequenas culturas e consumo doméstico. Os resultados mostraram que nenhuma das amostras apresentou valor de pH que comprometesse sua qualidade, tanto para uso na irrigação, quanto para consumo humano. No entanto, os íons bicarbonato e carbonato apresentaram grau de restrição que varia de leve a severo. Portanto, seu uso na agricultura demanda monitoramento e cuidados rigorosos para amenizar os efeitos negativos na produtividade e no solo.

  11. Lorentz Force Based Satellite Attitude Control

    Science.gov (United States)

    Giri, Dipak Kumar; Sinha, Manoranjan

    2016-07-01

    Since the inception of attitude control of a satellite, various active and passive control strategies have been developed. These include using thrusters, momentum wheels, control moment gyros and magnetic torquers. In this present work, a new technique named Lorentz force based Coulombic actuators for the active control is proposed. This method uses electrostatic charged shells, which interact with the time varying earth's magnetic field to establish a full three axes control of the satellite. It is shown that the proposed actuation mechanism is similar to a satellite actuated by magnetic coils except that the resultant magnetic moment vanishes under two different conditions. The equation for the required charges on the the Coulomb shells attached to the satellite body axes is derived, which is in turn used to find the available control torque for actuating the satellite along the orbit. Stability of the proposed system for very high initial angular velocity and exponential stability about the origin are proved for a proportional-differential control input. Simulations are carried out to show the efficacy of the proposed system for the attitude control of the earth-pointing satellite.

  12. Model based control of refrigeration systems

    Energy Technology Data Exchange (ETDEWEB)

    Sloth Larsen, L.F.

    2005-11-15

    The subject for this Ph.D. thesis is model based control of refrigeration systems. Model based control covers a variety of different types of controls, that incorporates mathematical models. In this thesis the main subject therefore has been restricted to deal with system optimizing control. The optimizing control is divided into two layers, where the system oriented top layers deals with set-point optimizing control and the lower layer deals with dynamical optimizing control in the subsystems. The thesis has two main contributions, i.e. a novel approach for set-point optimization and a novel approach for desynchronization based on dynamical optimization. The focus in the development of the proposed set-point optimizing control has been on deriving a simple and general method, that with ease can be applied on various compositions of the same class of systems, such as refrigeration systems. The method is based on a set of parameter depended static equations describing the considered process. By adapting the parameters to the given process, predict the steady state and computing a steady state gradient of the cost function, the process can be driven continuously towards zero gradient, i.e. the optimum (if the cost function is convex). The method furthermore deals with system constrains by introducing barrier functions, hereby the best possible performance taking the given constrains in to account can be obtained, e.g. under extreme operational conditions. The proposed method has been applied on a test refrigeration system, placed at Aalborg University, for minimization of the energy consumption. Here it was proved that by using general static parameter depended system equations it was possible drive the set-points close to the optimum and thus reduce the power consumption with up to 20%. In the dynamical optimizing layer the idea is to optimize the operation of the subsystem or the groupings of subsystems, that limits the obtainable system performance. In systems

  13. Net analyte signal based statistical quality control

    NARCIS (Netherlands)

    Skibsted, E.T.S.; Boelens, H.F.M.; Westerhuis, J.A.; Smilde, A.K.; Broad, N.W.; Rees, D.R.; Witte, D.T.

    2005-01-01

    Net analyte signal statistical quality control (NAS-SQC) is a new methodology to perform multivariate product quality monitoring based on the net analyte signal approach. The main advantage of NAS-SQC is that the systematic variation in the product due to the analyte (or property) of interest is sep

  14. Role-based access control in retrospect

    NARCIS (Netherlands)

    Franqueira, Virginia N.L.; Wieringa, Roel

    2012-01-01

    Role-Based Access Control (RBAC) has been a success in terms of the amount of research that went into it, its uptake in international standards, and its adoption by major software vendors. Yet, RBAC remains complex to implement in user organizations. In this paper we review the state of the art of R

  15. Atom-Role-Based Access Control Model

    Science.gov (United States)

    Cai, Weihong; Huang, Richeng; Hou, Xiaoli; Wei, Gang; Xiao, Shui; Chen, Yindong

    Role-based access control (RBAC) model has been widely recognized as an efficient access control model and becomes a hot research topic of information security at present. However, in the large-scale enterprise application environments, the traditional RBAC model based on the role hierarchy has the following deficiencies: Firstly, it is unable to reflect the role relationships in complicated cases effectively, which does not accord with practical applications. Secondly, the senior role unconditionally inherits all permissions of the junior role, thus if a user is under the supervisor role, he may accumulate all permissions, and this easily causes the abuse of permission and violates the least privilege principle, which is one of the main security principles. To deal with these problems, we, after analyzing permission types and role relationships, proposed the concept of atom role and built an atom-role-based access control model, called ATRBAC, by dividing the permission set of each regular role based on inheritance path relationships. Through the application-specific analysis, this model can well meet the access control requirements.

  16. CAMAC throughput of a new RISC-based data acquisition computer at the DIII-D tokamak

    Science.gov (United States)

    Vanderlaan, J. F.; Cummings, J. W.

    1993-10-01

    The amount of experimental data acquired per plasma discharge at DIII-D has continued to grow. The largest shot size in May 1991 was 49 Mbyte; in May 1992, 66 Mbyte; and in April 1993, 80 Mbyte. The increasing load has prompted the installation of a new Motorola 88100-based MODCOMP computer to supplement the existing core of three older MODCOMP data acquisition CPU's. New Kinetic Systems CAMAC serial highway driver hardware runs on the 88100 VME bus. The new operating system is MODCOMP REAL/IX version of AT&T System V UNIX with real-time extensions and networking capabilities; future plans call for installation of additional computers of this type for tokamak and neutral beam control functions. Experiences with the CAMAC hardware and software will be chronicled, including observation of data throughput. The Enhanced Serial Highway crate controller is advertised as twice as fast as the previous crate controller, and computer I/O speeds are expected to also increase data rates.

  17. Network-based production quality control

    Science.gov (United States)

    Kwon, Yongjin; Tseng, Bill; Chiou, Richard

    2007-09-01

    This study investigates the feasibility of remote quality control using a host of advanced automation equipment with Internet accessibility. Recent emphasis on product quality and reduction of waste stems from the dynamic, globalized and customer-driven market, which brings opportunities and threats to companies, depending on the response speed and production strategies. The current trends in industry also include a wide spread of distributed manufacturing systems, where design, production, and management facilities are geographically dispersed. This situation mandates not only the accessibility to remotely located production equipment for monitoring and control, but efficient means of responding to changing environment to counter process variations and diverse customer demands. To compete under such an environment, companies are striving to achieve 100%, sensor-based, automated inspection for zero-defect manufacturing. In this study, the Internet-based quality control scheme is referred to as "E-Quality for Manufacturing" or "EQM" for short. By its definition, EQM refers to a holistic approach to design and to embed efficient quality control functions in the context of network integrated manufacturing systems. Such system let designers located far away from the production facility to monitor, control and adjust the quality inspection processes as production design evolves.

  18. Control and data acquisition electronics for the CDF Silicon Vertex Detector

    Energy Technology Data Exchange (ETDEWEB)

    Turner, K.J.; Nelson, C.A.; Shaw, T.M.; Wesson, T.R.

    1991-11-01

    A control and data acquisition system has been designed for the CDF Silicon Vertex Detector (SVX) at Fermilab. The system controls the operation of the SVX Rev D integrated circuit (SVX IC) that is used to instrument a 46,000 microstrip silicon detector. The system consists of a Fastbus Sequencer, a Crate Controller and Digitizer modules. 11 refs., 6 figs., 3 tabs.

  19. CATS-based Air Traffic Controller Agents

    Science.gov (United States)

    Callantine, Todd J.

    2002-01-01

    This report describes intelligent agents that function as air traffic controllers. Each agent controls traffic in a single sector in real time; agents controlling traffic in adjoining sectors can coordinate to manage an arrival flow across a given meter fix. The purpose of this research is threefold. First, it seeks to study the design of agents for controlling complex systems. In particular, it investigates agent planning and reactive control functionality in a dynamic environment in which a variety perceptual and decision making skills play a central role. It examines how heuristic rules can be applied to model planning and decision making skills, rather than attempting to apply optimization methods. Thus, the research attempts to develop intelligent agents that provide an approximation of human air traffic controller behavior that, while not based on an explicit cognitive model, does produce task performance consistent with the way human air traffic controllers operate. Second, this research sought to extend previous research on using the Crew Activity Tracking System (CATS) as the basis for intelligent agents. The agents use a high-level model of air traffic controller activities to structure the control task. To execute an activity in the CATS model, according to the current task context, the agents reference a 'skill library' and 'control rules' that in turn execute the pattern recognition, planning, and decision-making required to perform the activity. Applying the skills enables the agents to modify their representation of the current control situation (i.e., the 'flick' or 'picture'). The updated representation supports the next activity in a cycle of action that, taken as a whole, simulates air traffic controller behavior. A third, practical motivation for this research is to use intelligent agents to support evaluation of new air traffic control (ATC) methods to support new Air Traffic Management (ATM) concepts. Current approaches that use large, human

  20. Nuclotron Control System

    Science.gov (United States)

    Volkov, V.; Gorchenko, V.; Kirichenko, A.; Kovalenko, A.; Kulikov, I.; Romanov, S.; Sveshnikov, B.; Vasilishin, B.

    1997-05-01

    The superconducting synchrotron named Nuclotron based on a miniature iron-shaped field SC-magnets was put into operation at the LHE JINR in 1993.The Nuclotron Control System (NCS) project,which is still under development,started in 1992 and has provided efficient support for the machine commissioning through all its phases.This paper presents the current status of the NCS. The control system architecture is hierarc- hical in nature and consists of two physical levels. High performance workstations,together with a general purpose server computers, are used at the top level.Workstations act as an operator consoles,while the servers provide massive disk data storage,printing utilities,a common database, program library and data exchange between Nuclotron and its experiments. The front-end level comprises as industrial com- puters equipped with I/O boards and data acquisition modules, as in- telligent CAMAC crate-controllers with embedded micro-PCs. NCS is distributed system,in which subsytems geographically separated by as much as 500 m.The total number of computers presently installed is 25. An Ethernet Local Area Network,which runs IPX/SPX and TCP/IP communi- cation protocols ,connects the console computers to the front-end le- vel and physicists workstations.

  1. FGMOS Based Voltage-Controlled Grounded Resistor

    Directory of Open Access Journals (Sweden)

    R. Pandey

    2010-09-01

    Full Text Available This paper proposes a new floating gate MOSFET (FGMOS based voltage-controlled grounded resistor. In the proposed circuit FGMOS operating in the ohmic region is linearized by another conventional MOSFET operating in the saturation region. The major advantages of FGMOS based voltage-controlled grounded resistor (FGVCGR are simplicity, low total harmonic distortion (THD, and low power consumption. A simple application of this FGVCGR as a tunable high-pass filter is also suggested. The proposed circuits operate at the supply voltages of +/-0.75 V. The circuits are designed and simulated using SPICE in 0.25-µm CMOS technology. The simulation results of FGVCGR demonstrate a THD of 0.28% for the input signal 0.32 Vpp at 45 kHz, and a maximum power consumption of 254 µW.

  2. Robust motion control of oscillatory-base manipulators h∞-control and sliding-mode-control-based approaches

    CERN Document Server

    Toda, Masayoshi

    2016-01-01

    This book provides readers with alternative robust approaches to control design for an important class of systems characteristically associated with ocean-going vessels and structures. These systems, which include crane vessels, on-board cranes, radar gimbals, and a conductivity temperature and depth winch, are modelled as manipulators with oscillating bases. One design approach is based on the H-infinity control framework exploiting an effective combination of PD control, an extended matrix polytope and a robust stability analysis method with a state-dependent coefficient form. The other is based on sliding-mode control using some novel nonlinear sliding surfaces. The model demonstrates how successful motion control can be achieved by suppressing base oscillations and in the presence of uncertainties. This is important not only for ocean engineering systems in which the problems addressed here originate but more generally as a benchmark platform for robust motion control with disturbance rejection. Researche...

  3. Memory-based parallel data output controller

    Science.gov (United States)

    Stattel, R. J.; Niswander, J. K. (Inventor)

    1984-01-01

    A memory-based parallel data output controller employs associative memories and memory mapping to decommutate multiple channels of telemetry data. The output controller contains a random access memory (RAM) which has at least as many address locations as there are channels. A word counter addresses the RAM which provides as it outputs an encoded peripheral device number and a MSB/LSB-first flag. The encoded device number and a bit counter address a second RAM which contains START and STOP flags to pick out the required bits from the specified word number. The LSB/MSB, START and STOP flags, along with the serial input digital data go to a control block which selectively fills a shift register used to drive the parallel data output bus.

  4. FPGA based Smart Wireless MIMO Control System

    Science.gov (United States)

    Usman Ali, Syed M.; Hussain, Sajid; Akber Siddiqui, Ali; Arshad, Jawad Ali; Darakhshan, Anjum

    2013-12-01

    In our present work, we have successfully designed, and developed an FPGA based smart wireless MIMO (Multiple Input & Multiple Output) system capable of controlling multiple industrial process parameters such as temperature, pressure, stress and vibration etc. To achieve this task we have used Xilin x Spartan 3E FPGA (Field Programmable Gate Array) instead of conventional microcontrollers. By employing FPGA kit to PC via RF transceivers which has a working range of about 100 meters. The developed smart system is capable of performing the control task assigned to it successfully. We have also provided a provision to our proposed system that can be accessed for monitoring and control through the web and GSM as well. Our proposed system can be equally applied to all the hazardous and rugged industrial environments where a conventional system cannot work effectively.

  5. Robust Controller Synthesis Based on Circle Criterion

    Science.gov (United States)

    Fuwa, Katsuhiko; Kato, Hiroyuki; Kando, Hisashi

    It is well-known that stability margins (gain and phase margins) are important quantitative indicators for evaluating stability in feedback control system synthesis. However, when we use conventional techniques based on such stability margins, it may be difficult to suppress the vibration from high-order modes of mechanical system. This paper proposes the robust controller synthesis which achieves both the conventional stability margins and the second phase margin which is a quantitative indicator for suppressing the vibration. The basic idea is to synthesize controller such that the Nyquist locus of open-loop transfer function encircles the immediate outer side of the circle which is specified by the conventional stability margins and the second phase margin. This is formulated as modified H∞ mixed sensitivity problem with the weighting constants which are decided by the center and radius of the circle.

  6. Model Based Control of Refrigeration Systems

    DEFF Research Database (Denmark)

    Larsen, Lars Finn Sloth

    of the supermarket refrigeration systems therefore greatly relies on a human operator to detect and accommodate failures, and to optimize system performance under varying operational condition. Today these functions are maintained by monitoring centres located all over the world. Initiated by the growing need...... for automation of these procedures, that is to incorporate some "intelligence" in the control system, this project was started up. The main emphasis of this work has been on model based methods for system optimizing control in supermarket refrigeration systems. The idea of implementing a system optimizing.......e. by degrading the performance. The method has been successfully applied on a test frigeration system for minimization of the power consumption; the hereby gained experimental results will be presented. The present control structure in a supermarket refrigeration system is distributed, which means...

  7. Sensor-based demand controlled ventilation

    Energy Technology Data Exchange (ETDEWEB)

    De Almeida, A.T. [Universidade de Coimbra (Portugal). Dep. Eng. Electrotecnica; Fisk, W.J. [Lawrence Berkeley National Lab., CA (United States)

    1997-07-01

    In most buildings, occupancy and indoor pollutant emission rates vary with time. With sensor-based demand-controlled ventilation (SBDCV), the rate of ventilation (i.e., rate of outside air supply) also varies with time to compensate for the changes in pollutant generation. In other words, SBDCV involves the application of sensing, feedback and control to modulate ventilation. Compared to ventilation without feedback, SBDCV offers two potential advantages: (1) better control of indoor pollutant concentrations; and (2) lower energy use and peak energy demand. SBDCV has the potential to improve indoor air quality by increasing the rate of ventilation when indoor pollutant generation rates are high and occupants are present. SBDCV can also save energy by decreasing the rate of ventilation when indoor pollutant generation rates are low or occupants are absent. After providing background information on indoor air quality and ventilation, this report provides a relatively comprehensive discussion of SBDCV. Topics covered in the report include basic principles of SBDCV, sensor technologies, technologies for controlling air flow rates, case studies of SBDCV, application of SBDCV to laboratory buildings, and research needs. SBDCV appears to be an increasingly attractive technology option. Based on the review of literature and theoretical considerations, the application of SBDCV has the potential to be cost-effective in applications with the following characteristics: (a) a single or small number of dominant pollutants, so that ventilation sufficient to control the concentration of the dominant pollutants provides effective control of all other pollutants; (b) large buildings or rooms with unpredictable temporally variable occupancy or pollutant emission; and (c) climates with high heating or cooling loads or locations with expensive energy.

  8. Access Control Based on Trail Inference

    Directory of Open Access Journals (Sweden)

    ALBARELO, P. C.

    2015-06-01

    Full Text Available Professionals are constantly seeking qualification and consequently increasing their knowledge in their area of expertise. Thus, it is interesting to develop a computer system that knows its users and their work history. Using this information, even in the case of professional role change, the system could allow the renewed authorization for activities, based on previously authorized use. This article proposes a model for user access control that is embedded in a context-aware environment. The model applies the concept of trails to manage access control, recording activities usage in contexts and applying this history as a criterion to grant new accesses. Despite the fact that previous related research works consider contexts, none of them uses the concept of trails. Hence, the main contribution of this work is the use of a new access control criterion, namely, the history of previous accesses (trails. A prototype was implemented and applied in an evaluation based on scenarios. The results demonstrate the feasibility of the proposal, allowing for access control systems to use an alternative way to support access rights.

  9. Access control mechanism of wireless gateway based on open flow

    Science.gov (United States)

    Peng, Rong; Ding, Lei

    2017-08-01

    In order to realize the access control of wireless gateway and improve the access control of wireless gateway devices, an access control mechanism of SDN architecture which is based on Open vSwitch is proposed. The mechanism utilizes the features of the controller--centralized control and programmable. Controller send access control flow table based on the business logic. Open vSwitch helps achieve a specific access control strategy based on the flow table.

  10. Control allocation and management of redundant control effectors based on bases sequenced optimal method

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    For an advanced aircraft, the amount of its effectors is much more than that for a traditional one, the functions of effectors are more complex and the coupling between each other is more severe. Based on the current control allocation research, this paper puts forward the concept and framework of the control allocation and management system for aircrafts with redundancy con-trol effectors. A new optimal control allocation method, bases sequenced optimal (BSO) method, is then presented. By analyz-ing the physical meaning of the allocation process of BSO method, four types of management strategies are adopted by the system, which act on the control allocation process under different flight conditions, mission requirements and effectors work-ing conditions. Simulation results show that functions of the control allocation system are extended and the system adaptability to flight status, mission requirements and effector failure conditions is improved.

  11. PI controller based model reference adaptive control for nonlinear ...

    African Journals Online (AJOL)

    user

    which can deal effectively for real-time online computer control. The NN of the ..... applications such as machine tools, industrial robot control, position control, and other engineering practices. .... Transactions on Mechatronics, vol.1, no.2, pp.

  12. Agents-based distributed processes control systems

    Directory of Open Access Journals (Sweden)

    Adrian Gligor

    2011-12-01

    Full Text Available Large industrial distributed systems have revealed a remarkable development in recent years. We may note an increase of their structural and functional complexity, at the same time with those on requirements side. These are some reasons why there are involvednumerous researches, energy and resources to solve problems related to these types of systems. The paper addresses the issue of industrial distributed systems with special attention being given to the distributed industrial processes control systems. A solution for a distributed process control system based on mobile intelligent agents is presented.The main objective of the proposed system is to provide an optimal solution in terms of costs, maintenance, reliability and flexibility. The paper focuses on requirements, architecture, functionality and advantages brought by the proposed solution.

  13. Design Novel Model Reference Artificial Intelligence Based Methodology to Optimized Fuel Ratio in IC Engine

    Directory of Open Access Journals (Sweden)

    FarzinPiltan

    2013-08-01

    Full Text Available In this research, model reference fuzzy based control is presented as robust controls for IC engine. The objective of the study is to design controls for IC engines without the knowledge of the boundary of uncertainties and dynamic information by using fuzzy model reference PD plus mass of air while improve the robustness of the PD plus mass of air control. A PD plus mass of air provides for eliminate the mass of air and ultimate accuracy in the presence of the bounded disturbance/uncertainties, although this methods also causes some oscillation. The fuzzy PD plus mass of air is proposed as a solution to the problems crated by unstability. This method has a good performance in presence of uncertainty.

  14. Indoor biology pollution control based on system-based humidity priority control strategy

    Institute of Scientific and Technical Information of China (English)

    刘亚昱; 谢慧; 石博强

    2009-01-01

    Indoor biological contamination and HVAC system secondary contamination problems caused wide public concerns. Biological contamination control will be the next step to achieve better IAQ. The most efficient and safe way to control biological contamination was to limit relative humidity in HVAC system and conditioned environment in the range that is more unsuitable for microorganism to survive. In this paper,by referring to bio-clean project experiences,a system-based humidity priority control manner came into being by lowering outdoor air humidity ratio to eliminate all indoor latent load and using self recirculation units to bear indoor sensible load. Based on the whole-course residue humidity contaminant control concept,dynamic step models for coil and conditioned zone were developed to describe mass and energy conservation and transformation processes. Then,HVAC system and conditioned zone dynamic models were established on LabVIEW+Matlab platform to investigate optimized regulation types,input signatures and control logics. Decoupling between cooling and dehumidification processes can be achieved and a more simplified and stable control system can be acquired by the system-based humidity priority control strategy. Therefore,it was a promising way for controlling biological pollution in buildings in order to achieve better IAQ.

  15. Design of Multi-unit Control System of High Voltage Power Supply for LASCAR Scintillator Detector Array

    Institute of Scientific and Technical Information of China (English)

    WuLijie; WangJinchuan; XiaoGuoqing; GuoZhongyan; ZhanWenlong; QiHuirong; XuZhiguo; ZhangLi; DingXianli; XuHushan; SunZhiyu; LiJiaxing; LiChen; WangMeng; ChenLixin; HuZhengguo; MaoRuishi; ZhaoTiecheng

    2003-01-01

    The power voltages of Photomultipliers (PMTs) at RIBLL LASCAR scintillator detector array are distributed between 900 V and 1 800 V irregularly. 392 CC123 modules are employed to supply high voltage for the PMT array. The CC123 module serves as PMT interface groupware package, and it can transform +12 V DC input voltage to ranges of 0~-2200 V for the PMT power supply corresponding to 0~+5 V output voltage from the control board crate. The relation of PMT power supply with the output voltage of the control crate is shown in Fig.1.

  16. Kinematics and Dynamics of Motion Control Based on Acceleration Control

    Science.gov (United States)

    Ohishi, Kiyoshi; Ohba, Yuzuru; Katsura, Seiichiro

    The first IEEE International Workshop on Advanced Motion Control was held in 1990 pointed out the importance of physical interpretation of motion control. The software servoing technology is now common in machine tools, robotics, and mechatronics. It has been intensively developed for the numerical control (NC) machines. Recently, motion control in unknown environment will be more and more important. Conventional motion control is not always suitable due to the lack of adaptive capability to the environment. A more sophisticated ability in motion control is necessary for compliant contact with environment. Acceleration control is the key technology of motion control in unknown environment. The acceleration control can make a motion system to be a zero control stiffness system without losing the robustness. Furthermore, a realization of multi-degree-of-freedom motion is necessary for future human assistance. A human assistant motion will require various control stiffness corresponding to the task. The review paper focuses on the modal coordinate system to integrate the various control stiffness in the virtual axes. A bilateral teleoperation is a good candidate to consider the future human assistant motion and integration of decentralized systems. Thus the paper reviews and discusses the bilateral teleoperation from the control stiffness and the modal control design points of view.

  17. PIC BASED SOLAR CHARGING CONTROLLER FOR BATTERY

    Directory of Open Access Journals (Sweden)

    Mrs Jaya N. Ingole

    2012-02-01

    Full Text Available Solar resource is unlimited the government is trying to implement the use of Solar panels as an energy source in rural and sub urban areas for lighting the street lights, but the battery used to store the power gets affected due to overcharge & discharges. This paper presents the use of PIC16F72 based solar charger controller for controlling the overcharging and discharging of a solar cell. It works by continuously optimizing the interface between the solar array and battery. First, the variable supply is fixed at 12.8V dc—the voltage of a fully charged battery— and linked to the battery point of the circuit. Cut Off of battery from load voltage is 10.8 volt. A PIC16F72 for small size and inbuilt analog inputs is used to determine voltage level of battery and solar panel..It also describes how the disadvantages of analog circuit are overcome by this controller. The flow chart is also provided.

  18. Digital Signal Controller Based Digital Control of Brushless DC Motor

    Directory of Open Access Journals (Sweden)

    Anjana Elizabeth Thomas

    2013-07-01

    Full Text Available This paper presents the digital control of a brushless dc (BLDC motor using TMS320F2812 DSP controller and an EPROM. The real-time control of electrical motors is an application area that is not usually the domain of Digital Signal Processors. The TMS320F2812 has got dedicated modules for digital motor control. Control algorithms used for the control has been in TMS320F2812 DSP controller. The output of the driver is 6 independent PWM pulses that have to be given to the corresponding gates of the six MOSFETs power switches used in the three-phase bridge driving circuit whose output is given to the stator of the Brushless DC Motor. The commutation technique used in this work is the trapezoidal commutation owing to its excellent speed and current control and it has been implemented using an EPROM

  19. Stability analysis of generalized predictive control based on Kleinman's controllers

    Institute of Scientific and Technical Information of China (English)

    DING Baocang; XI Yugeng

    2004-01-01

    With Kleinman's controller, its extended form and Riccati iteration as analyzing tools, the stability of GPC under various parameter cases is discussed. The overall closed-loop stability conclusions of GPC in equivalence with Kleinman's controller are obtained, which cover some existing results and provide the theoretical foundation for stable design of predictive control.

  20. Viabilidade técnica e econômica da caixa Embrapa para comercialização de tomate para consumo in natura Technical and economic viability of the Embrapa crate for marketing of fresh tomatoes

    Directory of Open Access Journals (Sweden)

    Nirlene J. Vilela

    2002-06-01

    Full Text Available Foram avaliadas as vantagens econômicas da nova embalagem desenvolvida pela Embrapa Hortaliças para comercialização de tomate para consumo in natura. A caixa tipo "K", embalagem mais usada no Brasil, tem grande número de características indesejáveis. Considerando os problemas da caixa tipo "K" e o alto índice de perdas pós-colheita na cadeia produtiva de hortaliças, a Embrapa Hortaliças iniciou um programa de pesquisa para o desenvolvimento de uma nova embalagem para tomate. O trabalho culminou com a definição da nova embalagem de plástico nomeada caixa Embrapa. Além de outras vantagens técnicas a nova embalagem, comparada com a caixa tipo "K", apresentou redução de perdas pós colheita (17%, considerando a conservação e integridade dos frutos. Para um horizonte de 5 anos, os indicadores econômicos para ambas embalagens, mostraram viabilidade econômica superior para a caixa Embrapa, sendo o valor presente líquido de, aproximadamente, R$ 60,7 mil e R$ 90,0 mil para a caixa tipo "K" e Caixa Embrapa, respectivamente. A taxa de benefício/custo foi de 4,80 e 7,80 para a caixa tipo "K" e caixa Embrapa, respectivamente. Considerando preços correntes e custos totais, a caixa Embrapa apresentou-se técnica e economicamente viável.The economic advantages of a new crate developed for commercialization of fresh tomatoes was evaluated. The Box type "K", name of the package for fresh vegetables crops mostly employed in Brazil, has many undesirables features. Considering the problems of box type "K" and the high index of post harvest losses in the production chain of vegetables, Embrapa Hortaliças started a research program focusing on the development of a new container for fresh tomatoes. This work ended with the adaptation of a new crate model made of plastic. This Embrapa crate showed comparative physical advantages of approximately 17% reduction in postharvest losses when compared to the box type K, considering conservation and

  1. Simulation-based Testing of Control Software

    Energy Technology Data Exchange (ETDEWEB)

    Ozmen, Ozgur [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Nutaro, James J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sanyal, Jibonananda [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Olama, Mohammed M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-02-10

    It is impossible to adequately test complex software by examining its operation in a physical prototype of the system monitored. Adequate test coverage can require millions of test cases, and the cost of equipment prototypes combined with the real-time constraints of testing with them makes it infeasible to sample more than a small number of these tests. Model based testing seeks to avoid this problem by allowing for large numbers of relatively inexpensive virtual prototypes that operate in simulation time at a speed limited only by the available computing resources. In this report, we describe how a computer system emulator can be used as part of a model based testing environment; specifically, we show that a complete software stack including operating system and application software - can be deployed within a simulated environment, and that these simulations can proceed as fast as possible. To illustrate this approach to model based testing, we describe how it is being used to test several building control systems that act to coordinate air conditioning loads for the purpose of reducing peak demand. These tests involve the use of ADEVS (A Discrete Event System Simulator) and QEMU (Quick Emulator) to host the operational software within the simulation, and a building model developed with the MODELICA programming language using Buildings Library and packaged as an FMU (Functional Mock-up Unit) that serves as the virtual test environment.

  2. Observer-based Satellite Attitude Control and Simulation Researches

    Institute of Scientific and Technical Information of China (English)

    王子才; 马克茂

    2002-01-01

    Observer design method is applied to the realization of satellite attitude control law baaed on simplified control model. Exact mathematical model of the satellite attitude control system is also constructed, together with the observer-based control law, to conduct simulation research. The simulation results justify the effectiveness andfeasibility of the observer-based control method.

  3. BDC 500 branch driver controller

    CERN Document Server

    Dijksman, A

    1981-01-01

    This processor has been designed for very fast data acquisition and date pre-processing. The dataway and branch highway speeds have been optimized for approximately 1.5 mu sec. The internal processor cycle is approximately 0.8 mu sec. The standard version contains the following functions (slots): crate controller type A1; branch highway driver including terminator; serial I/O port (TTY, VDU); 24 bit ALU and 24 bit program counter; 16 bit memory address counter and 4 word stack; 4k bit memory for program and/or data; battery backup for the memory; CNAFD and crate LAM display; request/grant logic for time- sharing operation of several BDCs. The free slots can be equipped with e.g. extra RAM, computer interfaces, hardware multiplier/dividers, etc. (0 refs).

  4. Optimal Control of Switched Systems based on Bezier Control Points

    Directory of Open Access Journals (Sweden)

    FatemeGhomanjani

    2012-06-01

    Full Text Available This paper presents a new approach for solving optimal control problems for switched systems. We focus on problems in which a pre-specified sequence of active subsystems is given. For such problems, we need to seek both the optimal switching instants and the optimal continuous inputs. A Bezier control points method is applied for solving an optimal control problem which is supervised by a switched dynamic system. Two steps of approximation exist here. First, the time interval is divided into k sub-intervals. Second, the trajectory and control functions are approximatedby Bezier curves in each subinterval. Bezier curves have been considered as piecewise polynomials of degree n, then they will be determined by n+1 control points on any subinterval. The optimal control problem is there by converted into a nonlinear programming problem (NLP, which can be solved by known algorithms. However in this paper the MATLAB optimization routine FMINCON is used for solving resulting NLP.

  5. HYBRID CONTROL OF HYDRAULIC PRESS MACHINE BASED ON ROBUST CONTROL

    Institute of Scientific and Technical Information of China (English)

    FANG Yu; YANG Jian; CHAI Xiaodong

    2008-01-01

    A robust control algorithm is proposed to focus on the non-linearity and variables of the hydraulic press machine with the proportional valve. The proposed robust controller does not need to design stable compensator in advance, which is simple in design and has large scope of uncertainty applications. The feedback gains of the proposed robust controller are small, so it is easily implemented in engineering applications. The theoretical and experimental research on the position and speed control of the hydraulic press machine is carried out. The control requirements of the hydraulic press machine during the working process are met in the position and speed at the same time. Experimental results show that the proposed controller has better robustness subject to load variables and adaptability of parameter variations of the hydraulic press machine with the proportional valve.

  6. Optimal Control of Switched Systems based on Bezier Control Points

    OpenAIRE

    FatemeGhomanjani; Mohammad HadiFarahi

    2012-01-01

    This paper presents a new approach for solving optimal control problems for switched systems. We focus on problems in which a pre-specified sequence of active subsystems is given. For such problems, we need to seek both the optimal switching instants and the optimal continuous inputs. A Bezier control points method is applied for solving an optimal control problem which is supervised by a switched dynamic system. Two steps of approximation exist here. First, the time interval is divided into ...

  7. FEATURE EXTRACTION FOR EMG BASED PROSTHESES CONTROL

    Directory of Open Access Journals (Sweden)

    R. Aishwarya

    2013-01-01

    Full Text Available The control of prosthetic limb would be more effective if it is based on Surface Electromyogram (SEMG signals from remnant muscles. The analysis of SEMG signals depend on a number of factors, such as amplitude as well as time- and frequency-domain properties. Time series analysis using Auto Regressive (AR model and Mean frequency which is tolerant to white Gaussian noise are used as feature extraction techniques. EMG Histogram is used as another feature vector that was seen to give more distinct classification. The work was done with SEMG dataset obtained from the NINAPRO DATABASE, a resource for bio robotics community. Eight classes of hand movements hand open, hand close, Wrist extension, Wrist flexion, Pointing index, Ulnar deviation, Thumbs up, Thumb opposite to little finger are taken into consideration and feature vectors are extracted. The feature vectors can be given to an artificial neural network for further classification in controlling the prosthetic arm which is not dealt in this paper.

  8. Switching Control System Based on Robust Model Reference Adaptive Control

    Institute of Scientific and Technical Information of China (English)

    HU Qiong; FEI Qing; MA Hongbin; WU Qinghe; GENG Qingbo

    2016-01-01

    For conventional adaptive control,time-varying parametric uncertainty and unmodeled dynamics are ticklish problems,which will lead to undesirable performance or even instability and nonrobust behavior,respectively.In this study,a class of discrete-time switched systems with unmodeled dynamics is taken into consideration.Moreover,nonlinear systems are here supposed to be approximated with the class of switched systems considered in this paper,and thereby switching control design is investigated for both switched systems and nonlinear systems to assure stability and performance.For robustness against unmodeled dynamics and uncertainty,robust model reference aclaptive control (RMRAC) law is developed as the basis of controller design for each individual subsystem in the switched systems or nonlinear systems.Meanwhile,two different switching laws are presented for switched systems and nonlinear systems,respectively.Thereby,the authors incorporate the corresponding switching law into the RMRAC law to construct two schemes of switching control respectively for the two kinds of controlled systems.Both closed-loop analyses and simulation examples are provided to illustrate the validity of the two proposed switching control schemes.Furthermore,as to the proposed scheme for nonlinear systems,its potential for practical application is demonstrated through simulations of longitudinal control for F-16 aircraft.

  9. Gesture Based Control and EMG Decomposition

    Science.gov (United States)

    Wheeler, Kevin R.; Chang, Mindy H.; Knuth, Kevin H.

    2005-01-01

    This paper presents two probabilistic developments for use with Electromyograms (EMG). First described is a new-electric interface for virtual device control based on gesture recognition. The second development is a Bayesian method for decomposing EMG into individual motor unit action potentials. This more complex technique will then allow for higher resolution in separating muscle groups for gesture recognition. All examples presented rely upon sampling EMG data from a subject's forearm. The gesture based recognition uses pattern recognition software that has been trained to identify gestures from among a given set of gestures. The pattern recognition software consists of hidden Markov models which are used to recognize the gestures as they are being performed in real-time from moving averages of EMG. Two experiments were conducted to examine the feasibility of this interface technology. The first replicated a virtual joystick interface, and the second replicated a keyboard. Moving averages of EMG do not provide easy distinction between fine muscle groups. To better distinguish between different fine motor skill muscle groups we present a Bayesian algorithm to separate surface EMG into representative motor unit action potentials. The algorithm is based upon differential Variable Component Analysis (dVCA) [l], [2] which was originally developed for Electroencephalograms. The algorithm uses a simple forward model representing a mixture of motor unit action potentials as seen across multiple channels. The parameters of this model are iteratively optimized for each component. Results are presented on both synthetic and experimental EMG data. The synthetic case has additive white noise and is compared with known components. The experimental EMG data was obtained using a custom linear electrode array designed for this study.

  10. Control and Data Acquisitions System for the spanish Beamline (BM25) at the ESRF; Sistema de Control y Acquisicion de Datos para la Linea Espanola (BN25) del ESRF

    Energy Technology Data Exchange (ETDEWEB)

    Pereira Gonzalez, A.; Olalla Garcia, C.; Sanchez Sanz, J.; Castro, G. R.

    2005-07-01

    A new control and data acquisition system has been developed for BM25 Spanish Line at the ESRF. The system is based in VMEbus, Motorola PreP architecture and Linux Operating System and it's linked to a local ETHERNET network which provides the way of communicate with the servers (PC workstations). In these computers, the data are available for general usage in order to analyze them. The data acquisition consists of many channels connected to the VME crates mainly, independent between them, and fully programmable by drivers, CLUI's and GUI's interfaces, and a set of independent systems (embedded ones, PLCs, others) controlling the security aspects. This report is described in terms of their architecture, their electronic system to the process hard ware and the functionality and the application development facilities they provide using the software and the data acquisition. (Author) 18 refs.

  11. Interfacing the septa movement (DC motors) equipment to the PS control system and the MIL1553 bus

    CERN Document Server

    Dehavay, Claude

    1995-01-01

    Continuing the rejuvenation of the PS Control system , this application replaces the Single Transceiver Hybrid used to interface the Septa Movement Fquipment by a G64 system connected to the VME crate via the MIL1553 bus. This note explains the G64 hardware interface and details the standard message as defined in the Control Protocole for Power Converter, RF and Stepping Motor equipment.

  12. Towards automatic model based controller design for reconfigurable plants

    DEFF Research Database (Denmark)

    Michelsen, Axel Gottlieb; Stoustrup, Jakob; Izadi-Zamanabadi, Roozbeh

    2008-01-01

    This paper introduces model-based Plug and Play Process Control, a novel concept for process control, which allows a model-based control system to be reconfigured when a sensor or an actuator is plugged into a controlled process. The work reported in this paper focuses on composing a monolithic m...

  13. Campus Access Control System RFID Based

    Directory of Open Access Journals (Sweden)

    Mr. SANTHOSH S

    2012-06-01

    Full Text Available Radio frequency identification (RFID technology has helped many organizations to reduce cost. Nevertheless, there are challenges and issues associated with RFID adoption. The most common internal challenge for many organizations is justifying the investment and modification of processes. The focus of this project is to show the business value of RFID technology and its applications. The important issue is the security level of the whole campus because it needs to be carefully differentiated. Dormitories and special research laboratories should benefit from higher levels of security than any other campuses. The key to the problem is represented by the new Radio Frequency Identification (RFID which can support contactless cards with memory. The most important feature of the proposed system is the updating of access permission level at any time for the user based on the availability of that user. The data transfer from the reader to the database was done using wireless communication (RF communication. To achieve this here RF transmitter and the RF receiver is used. The data which is read by the reader is sent to the microcontroller. Then from the controller we can transfer the data to the database by using the UART module (serial communication which is inbuilt in the microcontroller through RF transmitter. RF receiver of the same frequency at the receiver end receives and then stores the data in the database. RF transmitter and Receiver – frequency for transmitting and receiving the data depends on the user as per the requirement for the application and it is based on the range of distance. For the data encoding and decoding process HCS-101 protocol is used.

  14. Password Based Hand Gesture Controlled Robot

    Directory of Open Access Journals (Sweden)

    Shanmukha Rao

    2016-04-01

    Full Text Available Gesture is a most natural way of communication between human and computer in real system. Hand gesture is one of the important methods of non-verbal communications for humans. A simulation tool, MATLAB based colour image processing is used to recognize hand gesture. With the help of wireless communication, it is easier to interact with the robot. The objective of this project is to build a password protected wireless gesture control robot using Arduino, RF transmitter and receiver module. The continuous images are processed and the command signal is sent to the Arduino Uno microcontroller and according to the number of fingers, it sends the commands to the RF transmitter which is received by the transmitter and is processed at the receiver end which drives the motor to a particular direction. The robot moves forward, backward, right and left when we show one, two, three, four fingers (fingers with some red color band or tape respectively. As soon as the hand is moved off from the frame immediately it will stop. This can be used for physically disabled people who can’t use their hands to move the wheel chair. And it can also be used in various military applications where radioactive substances which can’t be touched by the human hand.

  15. UAV Robust Strategy Control Based on MAS

    Directory of Open Access Journals (Sweden)

    Jian Han

    2014-01-01

    Full Text Available A novel multiagent system (MAS has been proposed to integrate individual UAV (unmanned aerial vehicle to form a UAV team which can accomplish complex missions with better efficiency and effect. The MAS based UAV team control is more able to conquer dynamic situations and enhance the performance of any single UAV. In this paper, the MAS proposed and established combines the reacting and thinking abilities to be an initiative and autonomous hybrid system which can solve missions involving coordinated flight and cooperative operation. The MAS uses BDI model to support its logical perception and to classify the different missions; then the missions will be allocated by utilizing auction mechanism after analyzing dynamic parameters. Prim potential algorithm, particle swarm algorithm, and reallocation mechanism are proposed to realize the rational decomposing and optimal allocation in order to reach the maximum profit. After simulation, the MAS has been proved to be able to promote the success ratio and raise the robustness, while realizing feasibility of coordinated flight and optimality of cooperative mission.

  16. Control-based operating system design

    CERN Document Server

    Leva, Alberto; Papadopoulos, AV; Terraneo, F

    2013-01-01

    This book argues that computer operating system components should be conceived from the outset as controllers, synthesised and assessed in the system-theoretical world of dynamic models, and then realised as control algorithms.

  17. Flexible Tube-Based Network Control Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The Innovation Laboratory, Inc. builds a control system which controls the topology of an air traffic flow network and the network flow properties which enables Air...

  18. O processo de ensino e aprendizagem da disciplina de Química: o caso das escolas do ensino médio de Crateús/Ceará/Brasil

    Directory of Open Access Journals (Sweden)

    José Ossian Gadelha de Lima

    2012-12-01

    Full Text Available This work aims to define the reality lived by students and teachers of the Basic Teaching of the city of Crateús/Ceará/Brazil before the teaching and learning process of the discipline of Chemistry, trying to identify the causes of the low learning level and the little interest of the students for the subject. For the data gathering, two types of questionnaires were elaborated. One was answered by 08 (eight teachers and another by 60 (sixty students of 03 (three Public Schools of Basic Teaching of Crateús. From the results, two great factors can be pinpointed as responsible for the failure of the teaching and learning process of Chemistry in the High School level of those schools. One is related to the Fundamental Teaching by which those students went through. In the basic and essential disciplines (Portuguese and Mathematics they didn't achieve a satisfactory learning and they didn't acquire necessary basic knowledge to the understanding of the contents approached in the High School. The other reason refers to the teachers' formation that doesn't enough quality to perform their task. With its unsatisfactory formation, the teachers are forced the teach classes of low quality, not associating the Chemistry and the students’ reality.

  19. DC-based magnetic field controller

    Energy Technology Data Exchange (ETDEWEB)

    Kotter, Dale K. (Shelley, ID); Rankin, Richard A. (Ammon, ID); Morgan, John P,. (Idaho Falls, ID)

    1994-01-01

    A magnetic field controller for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage.

  20. DC-based magnetic field controller

    Energy Technology Data Exchange (ETDEWEB)

    Kotter, D.K.; Rankin, R.A.; Morgan, J.P.

    1994-05-31

    A magnetic field controller is described for laboratory devices and in particular to dc operated magnetic field controllers for mass spectrometers, comprising a dc power supply in combination with improvements to a Hall probe subsystem, display subsystem, preamplifier, field control subsystem, and an output stage. 1 fig.

  1. Embedded controllers for local board-control

    CERN Document Server

    Neufeld, Niko; Mini, Giuseppe; Sannino, Mario; Guzik, Zbigniew; Jacobsson, Richard; Jost, Beat

    2005-01-01

    The LHCb experiment at CERN has a large number of custom electronic boards performing high-speed data-processing. Like in any large experiment the control and monitoring of these crate-mounted boards must be integrated into the overall control-system. Traditionally this has been done by using buses like VME on the back-plane of the crates. LHCb has chosen to equip every board with an embedded micro-controller and connecting them in a large Local Area Network. The intelligence of these devices allows complex (soft) real-time control and monitoring, required for modern powerful FPGA driven electronics. Moreover each board has its own, isolated control access path, which increases the robustness of the entire system. The system is now in pre-production at several sites and will go into full production during next year. The hardware and software will be discussed and experiences from the R&D and pre-production will be reviewed, with an emphasis on advantages and difficulties of this approach to board-control.

  2. Disturbance Observer Based Control of Small Unmanned Aerial Rotorcraft

    Directory of Open Access Journals (Sweden)

    Xusheng Lei

    2013-01-01

    Full Text Available As a complex system, the control performance of small unmanned aerial rotorcraft is easily affected by the dynamic model errors, measurement errors, and environment disturbances. This paper proposes a disturbance observer based control method to improve performance. The disturbance observer based control is constructed by the feedback control and a series of integral filters. The system stability can be guaranteed by the feedback control method. Furthermore, the disturbances can be estimated and eliminated quickly by the integral filters. Therefore, the control performance can be improved effectively. The control performance of the disturbance observer based control has been validated by a series of flight tests. Compared with feedback control, the disturbance observer based control yields a better tracking performance in the presence of disturbances.

  3. SECONDARY VOLTAGE CONTROL BASED ON ADAPTIVE NEURAL PI CONTROLLERS

    Directory of Open Access Journals (Sweden)

    RUBEN TAPIA

    2010-01-01

    Full Text Available Este trabajo tiene como objetivo presentar el desempeño de un controlador basado en redes neuronales Bspline que regula el aporte de potencia reactiva de las máquinas síncronas. Debido a que los sistemas de potencia operan con parámetros no estacionarios y configuración cambiante, es preferible utilizar esquemas de control adaptativos. La tecnología de control debe asegurar su desempeño en términos de condiciones operativas prácticas de los sistemas de potencia, que considere la diversidad de cargas conectadas a la red y maximice la disponibilidad de recursos. La red neuronal Bspline es una herramienta conveniente para implementar el control adaptativo de voltaje, con la posibilidad de llevar a cabo ésta tarea enlínea considerando las no linealidades del sistema. El despacho de potencia reactiva se basa en la premisa de que cada máquina debe aportar en proporción a su capacidad nominal de operación. La aplicabilidad de la propuesta se demuestra mediante simulación en un sistema de potencia multimáquinas.

  4. Fault diagnosis based on controller modification

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2015-01-01

    Detection and isolation of parametric faults in closed-loop systems will be considered in this paper. A major problem is that a feedback controller will in general reduce the effects from variations in the systems including parametric faults on the controlled output from the system. Parametric...... time. A negative effect of increasing the amplitude of the auxiliary input is that the disturbances in the external output will be increased and consequently reduce the closed-loop performance. This problem can be handled by using a modification of the feedback controller. Applying the YJBK......-parameterization (after Youla, Jabr, Bongiorno and Kucera) for the controller, it is possible to modify the feedback controller with a minor effect on the closed-loop performance in the fault-free case and at the same time optimize the detection and isolation in a faulty case. Controller modification in connection...

  5. Optimization-Based Robust Nonlinear Control

    Science.gov (United States)

    2006-08-01

    IEEE Transactions on Automatic Control , vol. 51, no. 4, pp. 661...systems with two time scales", A.R. Teel, L. Moreau and D. Nesic, IEEE Transactions on Automatic Control , vol. 48, no. 9, pp. 1526-1544, September 2003...Turner, L. Zaccarian, IEEE Transactions on Automatic Control , vol. 48, no. 9, pp. 1509- 1525, September 2003. 5. "Nonlinear Scheduled anti-windup

  6. Feature Based Control of Compact Disc Players

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh

    Two servo control loops are used to keep the Optical Pick-up Unit focused and radially on the information track of the Compact Disc. These control servos have problems handling surface faults on the Compact Disc. In this Ph.D thesis a method is proposed to improve the handling of these surface...

  7. Gaze-Based Controlling a Vehicle

    DEFF Research Database (Denmark)

    Mardanbeigi, Diako; Witzner Hansen, Dan

    Research and applications of gaze interaction has mainly been conducted on a 2 dimensional surface (usually screens) for controlling a computer or controlling the movements of a robot. Emerging wearable and mobile technologies, such as google glasses may shift how gaze is used as an interactive...

  8. An Industrial Model Based Disturbance Feedback Control Scheme

    DEFF Research Database (Denmark)

    Kawai, Fukiko; Nakazawa, Chikashi; Vinther, Kasper

    2014-01-01

    This paper presents a model based disturbance feedback control scheme. Industrial process systems have been traditionally controlled by using relay and PID controller. However these controllers are affected by disturbances and model errors and these effects degrade control performance. The authors...... propose a new control method that can decrease the negative impact of disturbance and model errors. The control method is motivated by industrial practice by Fuji Electric. Simulation tests are examined with a conventional PID controller and the disturbance feedback control. The simulation results...

  9. Integrating Attributes into Role-Based Access Control

    DEFF Research Database (Denmark)

    Mahmood Rajpoot, Qasim; Jensen, Christian D.; Krishnan, Ram

    2015-01-01

    Role-based access control (RBAC) and attribute-based access control (ABAC) are currently the most prominent access control models. However, they both suffer from limitations and have features complimentary to each other. Due to this fact, integration of RBAC and ABAC has become a hot area...

  10. Bumpless Transfer between Observer-based Gain Scheduled Controllers

    DEFF Research Database (Denmark)

    Bendtsen, Jan Dimon; Stoustrup, Jakob; Trangbæk, Klaus

    2005-01-01

    This paper deals with bumpless transfer between a number of observer-based controllers in a gain scheduling architecture. Linear observer-based controllers are designed for a number of linear approximations of a nonlinear system in a set of operating points, and gain scheduling control can...

  11. Map-based control method for vehicle stability enhancement

    Institute of Scientific and Technical Information of China (English)

    Moon-Young Yoon; Seung-Hwan Baek; Kwang-Suk Boo; Heung-Seob Kim

    2015-01-01

    This work proposes a map-based control method to improve a vehicle’s lateral stability, and the performance of the proposed method is compared with that of the conventional model-referenced control method. Model-referenced control uses the sliding mode method to determine the compensated yaw moment;in contrast, the proposed map-based control uses the compensated yaw moment map acquired by vehicle stability analysis. The vehicle stability region is calculated by a topological method based on the trajectory reversal method. A 2-DOF vehicle model and Pacejka’s tire model are used to evaluate the proposed map-based control method. The properties of model-referenced control and map-based control are compared under various road conditions and driving inputs. Model-referenced control uses a control input to satisfy the linear reference model, and it generates unnecessary tire lateral forces that may lead to worse performance than an uncontrolled vehicle with step steering input on a road with a low friction coefficient. However, map-based control determines a compensated yaw moment to maintain the vehicle within the stability region, so the typical responses of vehicle enable to converge rapidly. The simulation results with sine and step steering show that map-based control provides better the tracking responsibility and control performance than model-referenced control.

  12. Controller design approach based on linear programming.

    Science.gov (United States)

    Tanaka, Ryo; Shibasaki, Hiroki; Ogawa, Hiromitsu; Murakami, Takahiro; Ishida, Yoshihisa

    2013-11-01

    This study explains and demonstrates the design method for a control system with a load disturbance observer. Observer gains are determined by linear programming (LP) in terms of the Routh-Hurwitz stability criterion and the final-value theorem. In addition, the control model has a feedback structure, and feedback gains are determined to be the linear quadratic regulator. The simulation results confirmed that compared with the conventional method, the output estimated by our proposed method converges to a reference input faster when a load disturbance is added to a control system. In addition, we also confirmed the effectiveness of the proposed method by performing an experiment with a DC motor.

  13. CAN-based Synchronized Motion Control for Induction Motors

    Institute of Scientific and Technical Information of China (English)

    Jun Ren; Chun-Wen Li; De-Zong Zhao

    2009-01-01

    A control area network (CAN) based multi-motor synchronized motion control system with an advanced synchronized control strategy is proposed.The strategy is to incorporate the adjacent cross-coupling control strategy into the sliding mode control architecture. As illustrated by the four-induction-motor-based experimental results,the multi-motor synchronized motion control system,via the CAN bus,has been successfully implemented.With the employment of the advanced synchronized motion control strategy,the synchronization performance can be significantly improved.

  14. Predictive Control Based upon State Space Models

    Directory of Open Access Journals (Sweden)

    Jens G. Balchen

    1989-04-01

    Full Text Available Repetitive online computation of the control vector by solving the optimal control problem of a non-linear multivariable process with arbitrary performance indices is investigated. Two different methods are considered in the search for an optimal, parameterized control vector: Pontryagin's Maximum Principle and optimization by using the performance index and its gradient directly. Unfortunately, solving this optimization problem has turned out to be a rather time-consuming task which has resulted in a time delay that cannot be accepted when the actual process is exposed to rapidly-varying disturbances. However, an instantaneous feedback strategy operating in parallel with the original control aogorithm was found to be able to cope with this problem.

  15. Simple Signal Source based Micro Controller

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    Using micro controller, DAC and Multi-periods syn-thesis, we can buildup a very simple signal source with precisefrequency, amplitude and waveform. Wave parameters can beprogrammed in advance. The circuit can satisfy some special re-quirements.

  16. Attendance Control System based on RFID technology

    OpenAIRE

    Nurbek Saparkhojayev; Selim Guvercin

    2012-01-01

    In Kazakhstan, checking students' attendance is one of the important issues for universities, because many universities evaluate students attendance and while giving the final grade, professors consider their total number of appearances on classes during the whole semester. This brings to the idea of having some tool to control students attendance. Some universities prefer to use paper sheet for controlling attendance, whereas some universities prefer to use paper sheet for checking students'...

  17. Fpga-based control of piezoelectric actuators

    Directory of Open Access Journals (Sweden)

    Juhász László

    2011-01-01

    Full Text Available In many industrial applications like semiconductor production and optical inspection systems, the availability of positioning systems capable to follow trajectory paths in the range of several centimetres, featuring at the same time a nanometre-range precision, is demanding. Pure piezoelectric stages and standard positioning systems with motor and spindle are not able to meet such requirements, because of the small operation range and inadequacies like backlash and friction. One concept for overcoming these problems consists of a hybrid positioning system built through the integration of a DC-drive in series with a piezoelectric actuator. The wide range of potential applications enables a considerable market potential for such an actuator, but due to the high variety of possible positioned objects and dynamic requirements, the required control complexity may be significant. In this paper, a real-time capable state-space control concept for the piezoelectric actuators, embedded in such a hybrid micropositioning system, is presented. The implementation of the controller together with a real-time capable hysteresis compensation measure is performed using a low-budget FPGA-board, whereas the superimposed integrated controller is realized with a dSPACE RCP-system. The advantages of the designed control over a traditional proportional-integral control structure are proven through experimental results using a commercially available hybrid micropositioning system. Positioning results by different dynamic requirements featuring positioning velocities from 1 μm/s up to 5 cm/s are given.

  18. Design of Industrial Robotic Controller Based on DSP

    Institute of Scientific and Technical Information of China (English)

    谈世哲; 杨汝清

    2003-01-01

    This paper describes the design of industrial robot controller based on the DSP technology. Robotic real time control is realized by PC and DSP motion control card and this method improves the performance of robotic controller. Finally this paper gives some experiment results and conclusion.

  19. A model–based approach to fault–tolerant control

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2012-01-01

    reconfiguration part. The theoretical basis for the architecture is given followed by an investigation of the single parts in the architecture. It is shown that the general controller parameterization is central in connection with both fault diagnosis as well as controller reconfiguration. Especially in relation......A model-based controller architecture for Fault-Tolerant Control (FTC) is presented in this paper. The controller architecture is based on a general controller parameterization. The FTC architecture consists of two main parts, a Fault Detection and Isolation (FDI) part and a controller...... to the controller reconfiguration part, the application of controller parameterization results in a systematic technique for switching between different controllers. This also allows controller switching using different sets of actuators and sensors....

  20. Knowledge based support for multiagent control and automation

    DEFF Research Database (Denmark)

    Saleem, Arshad; Lind, Morten

    2011-01-01

    This paper presents a mechanism for developing knowledge based support in multiagent based control and diagnosis. In particular it presents a way for autonomous agents to utilize a qualitative means-ends based model for reasoning about control situations. The proposed mechanism have been used in ...

  1. Cobacabana (control of balance by card-based navigation) : A card-based system for job shop control

    NARCIS (Netherlands)

    Land, M.J.

    2009-01-01

    Existing card-based production control systems such as Kanban are mostly dedicated to repetitive production environments. Cards-based systems for job shop control are lacking, while particularly this industry segment shows a need for simple control systems. This paper aims at filling the gap by pres

  2. Cobacabana (control of balance by card-based navigation) : A card-based system for job shop control

    NARCIS (Netherlands)

    Land, M.J.

    Existing card-based production control systems such as Kanban are mostly dedicated to repetitive production environments. Cards-based systems for job shop control are lacking, while particularly this industry segment shows a need for simple control systems. This paper aims at filling the gap by

  3. Robot Control System based on Web Application and RFID Technology

    Directory of Open Access Journals (Sweden)

    Barenji Ali Vatankhah

    2015-01-01

    Full Text Available This paper discusses an integration driven framework for enabling the RFID based identification of parts to perform robotic distributor operations in the random mix based parts control based on web application. The RFID technology senses newly arriving parts to be distribution robot, the robot is able to recognize them and perform cooperative distributing via web-based application. The developed web application control system is implemented in the educational robotic arm. RFID system sends real time information from parts to the web application and web based application makes a decision for control of the robot arm, controller of robot controls the robot as based on the decision from web application. The proposed control system has increases the reconfiguration and scalability of robot system.

  4. Similarity based mixed transaction concurrency control protocol

    Institute of Scientific and Technical Information of China (English)

    PAN Yi; LU Yan-sheng

    2005-01-01

    Due to the various performance requirements and data access restrictions of different types of real-time transactions, concurrency control protocols which had been designed for the systems with single type of transactions are not sufficient for mixed real-time database systems (MRTDBS), where different types of real-time transactions coexist in the systems concurrently. In this paper, a new concurrency control protocol MRTT_CC for mixed real-time transactions is proposed. The new strategy integrates with different concurrency control protocols to meet the deadline requirements of different types of real-time transactions. The data similarity concept is also explored in the new protocol to reduce the blocking time of soft real-time transactions, which increases their chances to meet the deadlines. Simulation experiments show that the new protocol has gained good performance.

  5. Estimator Based Controller for High Speed Flywheel Magnetic Bearing System

    Science.gov (United States)

    Dever, Timothy P.; Brown, Gerald V.; Jansen, Ralph H.

    2002-01-01

    A flywheel system and its operator interface are described. Measurements of magnetic bearing negative stiffness are performed. Two digital magnetic bearing control algorithms (PD and estimator based) are defined and their implementations are described. Tuning of each controller is discussed. Comparison of the two controllers' stability, damping noise, and operating current are described. Results describing the superiority of the estimator-based controller are presented and discussed.

  6. DeviceNet-based device-level control in SSRF

    CERN Document Server

    Leng Yong Bin; Lu Cheng Meng; Miao Hai Feng; Liu Song Qiang; Shen Guo Bao

    2002-01-01

    The control system of Shanghai Synchrotron Radiation Facility is an EPICS-based distributed system. One of the key techniques to construct the system is the device-level control. The author describes the design and implementation of the DeviceNet-based device controller. A prototype of the device controller was tested in the experiments of magnet power supply and the result showed a precision of 3 x 10 sup - sup 5

  7. Observer-based Controller For Microrobot in Pulsatile Blood Flow

    OpenAIRE

    Sadelli, Lounis; Fruchard, Matthieu; Ferreira, Antoine

    2014-01-01

    International audience; We propose an observer-based controller for a magnetic microrobot immersed in the human vasculature. The drag force depends on the pulsatile blood velocity and specially acts on the microrobot dynamics. In the design of advanced control laws, the blood velocity is usually assumed to be known or set to a constant mean value to achieve the control objectives, whereas the sole robot position is measured. We prove the stability of the proposed observer-based controller com...

  8. Model based control of dynamic atomic force microscope

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chibum [Department of Mechanical System Design Engineering, Seoul National University of Science and Technology, Seoul 139-743 (Korea, Republic of); Salapaka, Srinivasa M., E-mail: salapaka@illinois.edu [Department of Mechanical Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801 (United States)

    2015-04-15

    A model-based robust control approach is proposed that significantly improves imaging bandwidth for the dynamic mode atomic force microscopy. A model for cantilever oscillation amplitude and phase dynamics is derived and used for the control design. In particular, the control design is based on a linearized model and robust H{sub ∞} control theory. This design yields a significant improvement when compared to the conventional proportional-integral designs and verified by experiments.

  9. Model based control of dynamic atomic force microscope.

    Science.gov (United States)

    Lee, Chibum; Salapaka, Srinivasa M

    2015-04-01

    A model-based robust control approach is proposed that significantly improves imaging bandwidth for the dynamic mode atomic force microscopy. A model for cantilever oscillation amplitude and phase dynamics is derived and used for the control design. In particular, the control design is based on a linearized model and robust H(∞) control theory. This design yields a significant improvement when compared to the conventional proportional-integral designs and verified by experiments.

  10. Power system stabilizers based on modern control techniques

    Energy Technology Data Exchange (ETDEWEB)

    Malik, O.P.; Chen, G.P.; Zhang, Y.; El-Metwally, K. [Calgary Univ., AB (Canada). Dept. of Electrical and Computer Engineering

    1994-12-31

    Developments in digital technology have made it feasible to develop and implement improved controllers based on sophisticated control techniques. Power system stabilizers based on adaptive control, fuzzy logic and artificial networks are being developed. Each of these control techniques possesses unique features and strengths. In this paper, the relative performance of power systems stabilizers based on adaptive control, fuzzy logic and neural network, both in simulation studies and real time tests on a physical model of a power system, is presented and compared to that of a fixed parameter conventional power system stabilizer. (author) 16 refs., 45 figs., 3 tabs.

  11. Design of energy-based terrain following flight control system

    Science.gov (United States)

    Wang, Wei; Li, Aijun; Xie, Yanwu; Tan, Jian

    2006-11-01

    Historically, aircraft longitudinal control has been realized by means of two loops: flight path (the control variable is elevator displacement) and speed control (the control variable is propulsive thrust or engine power). Both the elevator and throttle control cause coupled altitude and speed response, which exerts negative effects on longitudinal flight performance of aircraft, especially for Terrain Following(TF) flight. Energy-based method can resolve coupled problem between flight speed and path by controlling total energy rate and energy distribution rate between elevator and throttle. In this paper, energy-based control method is applied to design a TF flight control system for controlling flight altitude directly. An error control method of airspeed and altitude is adopted to eliminate the stable error of the total energy control system when decoupling control. Pitch loop and pitch rate feedback loop are designed for the system to damp the oscillatory response produced by TF system. The TF flight control system structure diagram and an aircraft point-mass energy motion model including basic control loops are given and used to simulate decoupling performance of the TF fight control system. Simulation results show that the energy-based TF flight control system can decouple flight velocity and flight path angle, exactly follow planned flight path, and greatly reduce altitude error, which is between +10m and -8m.

  12. Design of Threshold Controller Based Chaotic Circuits

    DEFF Research Database (Denmark)

    Mohamed, I. Raja; Murali, K.; Sinha, Sudeshna

    2010-01-01

    We propose a very simple implementation of a second-order nonautonomous chaotic oscillator, using a threshold controller as the only source of nonlinearity. We demonstrate the efficacy and simplicity of our design through numerical and experimental results. Further, we show that this approach of ...

  13. Power-based control of physical systems

    NARCIS (Netherlands)

    Garcia-Canseco, Eloisa; Jeltsema, Dimitri; Ortega, Romeo; Scherpen, Jacquelien M. A.

    2010-01-01

    It is well known that energy-balancing control is stymied by the presence of pervasive dissipation. To overcome this problem in electrical circuits, the alternative paradigm of power shaping was introduced in Ortega, Jeltsema, and Scherpen (2003)-where, as suggested by its name, stabilization is ach

  14. Model-based control of hopper dredgers

    NARCIS (Netherlands)

    Braaksma, J.

    2008-01-01

    The modern trailing suction hopper dredgers are advanced ships that are equipped with many automation systems that can be controlled with integrated computer systems from the bridge. From the operators it is expected that they generate the right set-points for all these systems. The latest ships are

  15. Plant-based strategies for mosquito control

    Science.gov (United States)

    Mosquitoes transmit some of the most devastating emerging infectious diseases of humans, domestic animals, and wildlife. Although vector control by use of chemical insecticides has played an important role in prevention and management of these diseases, their sustained use remains questionable due t...

  16. Application analysis of servo-control system based on PMAC with feed-forward control

    Science.gov (United States)

    Lin, Rongkun; Yao, Bin; Chen, Minghui; Li, Fei; Peng, Liwen

    2011-12-01

    On the basis of traditional PID algorithm, the paper analyzes the improvements of control algorithm of PMAC (Programmable Multiple-Axis Controller) with feedforward control, and presents the computational model of the control algorithm. The debugging results of motors are analyzed in combination with PMAC as the controller. The problems and the final graphics data that appear throughout debugging process are analyzed in detail, which proves that there are better steady characteristics and dynamic performance for the servo-control system based on PMAC with feedforward control. The control system is rebuilded by parameter-adaptive PID+feedforward control for higher machining accuracy.

  17. Velocity and Motion Control of a Self-balancing Vehicle based on a Cascade Control Strategy

    Directory of Open Access Journals (Sweden)

    Miguel Velazquez

    2016-06-01

    Full Text Available This paper presents balancing, velocity and motion control of a self-balancing vehicle. A cascade controller is implemented for both balancing control and angular velocity control. This controller is tested in simulations using a proposed mathematical model of the system. Motion control is achieved based on the kinematics of the robot. Control hardware is designed and integrated to implement the proposed controllers. Pitch is kept under 1° from the equilibrium position with no external disturbances. The linear cascade control is able to handle slight changes in the system dynamics, such as in the centre of mass and the slope on an inclined surface.

  18. Velocity and Motion Control of a Self-Balancing Vehicle Based on a Cascade Control Strategy

    Directory of Open Access Journals (Sweden)

    Miguel Velazquez

    2016-06-01

    Full Text Available This paper presents balancing, velocity and motion control of a self-balancing vehicle. A cascade controller is implemented for both balancing control and angular velocity control. This controller is tested in simulations using a proposed mathematical model of the system. Motion control is achieved based on the kinematics of the robot. Control hardware is designed and integrated to implement the proposed controllers. Pitch is kept under 1° from the equilibrium position with no external disturbances. The linear cascade control is able to handle slight changes in the system dynamics, such as in the centre of mass and the slope on an inclined surface.

  19. Guidance on Design of Internet-based Process Control Systems

    Institute of Scientific and Technical Information of China (English)

    S.H.YANG; L.YANG

    2005-01-01

    Internet-based process control is becoming new generations of control systems, in which the Internet is used as a platform for global remote monitoring and control. The obvious benefit is to enable global collaboration between operators from geographically dispersed locations, data sharing and data provision for remote monitoring and control. However, connection to an open network and the use of universal technology present new problems that did not exist with the conventional design and construction of control systems, such as time delay and data loss in Internet transmission and security. This paper reviews the latest research results and presents design guidance of Internet based monitoring and control systems.

  20. Model-based analysis of control performance in sewer systems

    DEFF Research Database (Denmark)

    Mollerup, Ane Høyer; Mauricio Iglesias, Miguel; Johansen, N.B.;

    2012-01-01

    Design and assessment of control in wastewater systems has to be tackled at all levels, including supervisory and regulatory level. We present here an integrated approach to assessment of control in sewer systems based on modelling and the use of process control tools to assess the controllability...... of the process. A case study of a subcatchment area in Copenhagen (Denmark) is used to illustrate the combined approach in modelling of the system and control assessment....

  1. Reinforcement learning based backstepping control of power system oscillations

    Energy Technology Data Exchange (ETDEWEB)

    Karimi, Ali; Eftekharnejad, Sara; Feliachi, Ali [Advanced Power and Electric Research Center (APERC), West Virginia University, Morgantown, WV 26506-6109 (United States)

    2009-11-15

    This paper proposes a reinforcement learning based backstepping control technique for damping oscillations in electric power systems using the generators excitation systems. Decentralized controllers are first designed using the backstepping technique. Then, reinforcement learning is used to tune the gains of these controllers to adapt to various operating conditions. Simulation results for a two area power system show that the proposed control technique provides better damping than (i) conventional power system stabilizers and (ii) backstepping fixed gain controllers. (author)

  2. Radio Frequency Based Water Level Monitor and Controller for ...

    African Journals Online (AJOL)

    Radio Frequency Based Water Level Monitor and Controller for Residential Applications. ... Nigerian Journal of Technology ... This paper elucidates a radio frequency (RF) based transmission and reception system used to remotely monitor ...

  3. Hombre y muerte en el Islam: o de cómo la muerte de Sócrates fue objeto de considerácion en la civilización árabe-musulmana

    Directory of Open Access Journals (Sweden)

    Guerrero, Rafael Ramón

    2007-01-01

    Full Text Available A la muerte, que afecta a todo hombre, alude en numerosas ocasiones el Corán. Quizá por ello pronto se planteó en el mundo islámico la cuestión del suicidio y de la muerte voluntaria. Desde el siglo IX, este problema se convirtió en objeto de consideración, provocado por el impacto de la filosofía antigua: parece que la figura de Sócrates ejerció un cierto influjo a través de las versiones que de su muerte, aceptada voluntariamente, llegaron al mundo islámico y fue motivo de reflexión por parte de muchos pensadores

  4. Flatness-based fault tolerant control

    Directory of Open Access Journals (Sweden)

    César Martínez-Torres

    2014-01-01

    Full Text Available Este artículo presenta un método de control tolerante a fallas para sistemas no lineales planos. Las propiedades intrínsecas d e los sistemas planos generan redundancia analítica y permiten calcular todos los estados y las entradas de control del sistema. Los residuo s son calculados comparando las medidas reales provenientes de los se nsores y las señales obtenidas gracias al conjunto de ecuacione s del sistema plano. Fallas multiplicativas y aditivas se pueden man ejar de manera indistinta. Las señales redundantes obtenidas co n las ecuaciones del sistema plano son usadas para reconfigurar el si stema con falla. La factibilidad del método propuesto es verifi cada para fallas aditivas en un sistema de tres tanques.

  5. PLC based Smart Street Lighting Control

    Directory of Open Access Journals (Sweden)

    D.V.Pushpa Latha

    2013-12-01

    Full Text Available Conventional street lighting systems in most of the areas are Online at regular intervals of time irrespective of the seasonal variations. The street lights are simply switched on at afternoon and turned off in the morning. The consequence is that a large amount of Power is wasted meaninglessly. As energy consumption is an issue of increasing interest, possible energy savings in public street lighting systems are recently discussed from different viewpoints. The purpose of this work is to describe the Smart Street Lighting system, an approach to accomplish the demand for flexible public lighting systems using a Programmable Logic controller (PLC. The main difference from other computers is that PLCs are armoured for severe conditions such as dust, moisture, heat, cold etc., and have the facility for extensive input/output (I/O arrangements. In the proposed paper, street lights are controlled using millennium 3 PLC taking the seasonal variations into consideration.

  6. CICERO: Control Information system Concepts based\

    CERN Multimedia

    2002-01-01

    RD38 : Modern High Energy Physics experiments and accelerators require sophisticated control systems to ensure their safe operation and to optimise their performance. Due to their complexity and to the large number of sensors needed for these purposes, they turn out to be difficult and costly to maintain with the present technology. The situation will seriously worsen with the LHC era. Various R\\&D departments of industrial companies are directly concerned with similar difficulties in power plants and complex automated systems. We propose to combine our efforts to study the various aspects of this problem. We intend to outline the main building blocks of generic control information system. As a result of this study we aim to provide technical solutions which could later be the major components of a basic turnkey system for medium to large scale HEP experiments and accelerators.

  7. Internal Model Based Active Disturbance Rejection Control

    OpenAIRE

    Pan, Jinwen; Wang, Yong

    2016-01-01

    The basic active disturbance rejection control (BADRC) algorithm with only one order higher extended state observer (ESO) proves to be robust to both internal and external disturbances. An advantage of BADRC is that in many applications it can achieve high disturbance attenuation level without requiring a detailed model of the plant or disturbance. However, this can be regarded as a disadvantage when the disturbance characteristic is known since the BADRC algorithm cannot exploit such informa...

  8. Wake Identification Based Wake Impact Alleviation Control

    OpenAIRE

    Ehlers, Jana; Fischenberg, Dietrich; Niedermeier, Dominik

    2014-01-01

    During a wake vortex encounter an aircraft is exposed to strong unsteady disturbance velocities which can lead to significant changes in the aircraft attitude and flight path. This can represent a severe safety risk and can result in injuries to the passengers and crew as well as damages to the aircraft. The application of a wake impact alleviation control system can considerably decrease the aircraft’s response during the wake encounter, and hence diminish the pilot workload while reducing t...

  9. Organic Based Solar Cells with Morphology Control

    OpenAIRE

    Andersen, Thomas Rieks; Bundgaard, Eva; Jørgensen, Mikkel

    2013-01-01

    The field of organic solar cells has in the last years gone through an impressive development with efficiencies reported up to 12 %. For organic solar cells to take the leap from primarily being a laboratory scale technology to being utilized as renewable energy source, several issues need to be addressed. Among these are a more direct transfer of new materials tested on a laboratory scale to large scale production than offered by spincoating, a method offering direct control of the morpholog...

  10. Quality control based on electrical resistivity measurements

    OpenAIRE

    Ferreira, Rui Miguel; Jalali, Said

    2006-01-01

    The electrical resistivity of concrete is one of the main parameters controlling the initiation and propagation of reinforcement corrosion. It is common knowledge that concrete electrical resistivity is mainly dependent on the w/c ratio (pore connectivity), volume and type of cement, temperature and the moisture. This research work studies the effect of specimen shape and temperature of measurement on electrical resistivity measurements of concrete using the four-point Werner electrode. In ad...

  11. Toward Inverse Control of Physics-Based Sound Synthesis

    Science.gov (United States)

    Pfalz, A.; Berdahl, E.

    2017-05-01

    Long Short-Term Memory networks (LSTMs) can be trained to realize inverse control of physics-based sound synthesizers. Physics-based sound synthesizers simulate the laws of physics to produce output sound according to input gesture signals. When a user's gestures are measured in real time, she or he can use them to control physics-based sound synthesizers, thereby creating simulated virtual instruments. An intriguing question is how to program a computer to learn to play such physics-based models. This work demonstrates that LSTMs can be trained to accomplish this inverse control task with four physics-based sound synthesizers.

  12. Torque Ripple Reduction in Direct Torque Control Based Induction Motor using Intelligent Controllers

    Science.gov (United States)

    Sudhakar, Ambarapu; Vijaya Kumar, M.

    2015-09-01

    This paper presents intelligent control scheme together with conventional control scheme to overcome the problems with uncertainties in the structure encountered with classical model based design of induction motor drive based on direct torque control (DTC). It allows high dynamic performance to be obtained with very simple hysteresis control scheme. Direct control of the torque and flux is achieved by proper selection of inverter voltage space vector through a lookup table. This paper also presents the application of intelligent controllers like neural network and fuzzy logic controllers to control induction machines with DTC. Intelligent controllers are used to emulate the state selector of the DTC. With implementation of intelligent controllers the system is also verified and proved to be operated stably with reduced torque ripple. The proposed method validity and effectiveness has been verified by computer simulations using Matlab/Simulink®. These results are compared with the ones obtained with a classical DTC using proportional integral speed controller.

  13. A Hybrid Sensor Based Backstepping Control Approach with its Application to Fault-Tolerant Flight Control

    NARCIS (Netherlands)

    Sun, L.G.; De Visser, C.C.; Chu, Q.P.; Falkena, W.

    2013-01-01

    Recently, an incremental type sensor based backstepping (SBB) control approach, based on singular perturbation theory and Tikhonov’s theorem, has been proposed. This Lyapunov function based method uses measurements of control variables and less model knowledge, and it is not susceptible to the model

  14. A Hybrid Sensor Based Backstepping Control Approach with its Application to Fault-Tolerant Flight Control

    NARCIS (Netherlands)

    Sun, L.G.; De Visser, C.C.; Chu, Q.P.; Falkena, W.

    2013-01-01

    Recently, an incremental type sensor based backstepping (SBB) control approach, based on singular perturbation theory and Tikhonov’s theorem, has been proposed. This Lyapunov function based method uses measurements of control variables and less model knowledge, and it is not susceptible to the model

  15. Mechanics and model-based control of advanced engineering systems

    CERN Document Server

    Irschik, Hans; Krommer, Michael

    2014-01-01

    Mechanics and Model-Based Control of Advanced Engineering Systems collects 32 contributions presented at the International Workshop on Advanced Dynamics and Model Based Control of Structures and Machines, which took place in St. Petersburg, Russia in July 2012. The workshop continued a series of international workshops, which started with a Japan-Austria Joint Workshop on Mechanics and Model Based Control of Smart Materials and Structures and a Russia-Austria Joint Workshop on Advanced Dynamics and Model Based Control of Structures and Machines. In the present volume, 10 full-length papers based on presentations from Russia, 9 from Austria, 8 from Japan, 3 from Italy, one from Germany and one from Taiwan are included, which represent the state of the art in the field of mechanics and model based control, with particular emphasis on the application of advanced structures and machines.

  16. Z Number Based Fuzzy Inference System for Dynamic Plant Control

    Directory of Open Access Journals (Sweden)

    Rahib H. Abiyev

    2016-01-01

    Full Text Available Frequently the reliabilities of the linguistic values of the variables in the rule base are becoming important in the modeling of fuzzy systems. Taking into consideration the reliability degree of the fuzzy values of variables of the rules the design of inference mechanism acquires importance. For this purpose, Z number based fuzzy rules that include constraint and reliability degrees of information are constructed. Fuzzy rule interpolation is presented for designing of an inference engine of fuzzy rule-based system. The mathematical background of the fuzzy inference system based on interpolative mechanism is developed. Based on interpolative inference process Z number based fuzzy controller for control of dynamic plant has been designed. The transient response characteristic of designed controller is compared with the transient response characteristic of the conventional fuzzy controller. The obtained comparative results demonstrate the suitability of designed system in control of dynamic plants.

  17. Stabilization of model-based networked control systems

    Science.gov (United States)

    Miranda, Francisco; Abreu, Carlos; Mendes, Paulo M.

    2016-06-01

    A class of networked control systems called Model-Based Networked Control Systems (MB-NCSs) is considered. Stabilization of MB-NCSs is studied using feedback controls and simulation of stabilization for different feedbacks is made with the purpose to reduce the network trafic. The feedback control input is applied in a compensated model of the plant that approximates the plant dynamics and stabilizes the plant even under slow network conditions. Conditions for global exponential stabilizability and for the choosing of a feedback control input for a given constant time between the information moments of the network are derived. An optimal control problem to obtain an optimal feedback control is also presented.

  18. Machine function based control code algebras

    NARCIS (Netherlands)

    Bergstra, J.A.

    2008-01-01

    Machine functions have been introduced by Earley and Sturgis in [6] in order to provide a mathematical foundation of the use of the T-diagrams proposed by Bratman in [5]. Machine functions describe the operation of a machine at a very abstract level. A theory of hardware and software based on machin

  19. TCSC controller design based on output feedback control with linear matrix inequality

    Energy Technology Data Exchange (ETDEWEB)

    Ishimaru, Masachika; Shirai, Goro [Hosei University, Tokyo (Japan). Dept. of Electrical Engineering; Niioka, Satoru; Yokoyama, Ryuichi [Tokyo Metropolitan University (Japan). Dept. of Electrical Engineering

    2000-07-01

    The authors aim at designing the fast responsible and robust stabilizing controller. Recently, many researches propose robust stabilizing compensators based on H{sub {infinity}} control theory. Especiady, the LMI (Linear Matrix Inequality) solving efficient convex problems is very effective. LMI is based on a linear function composed by matrices, and it is expansion of conventional H{sub {infinity}} control. In addition to the LMI approach, authors pay attention to the output-feedback control for stabilizing a system using observable output values. This paper presents a stabilizing control using measurable values by using the output-feedback method. In order to discuss the advantage of the proposed method, 3-machine 9-bus system is used. Moreover, this system is applied TCSC (Thyristor Controlled Series Capacitor) controllers, and H{sub {infinity}} control based on the LMI is proposed for the design method of TCSC controllers to attain the robust stability. (author)

  20. Comparative Analysis for NN-Based Adaptive Back-stepping Controller and Back-stepping Controller

    OpenAIRE

    Margarita Gjonaj; BetimÇiço; ArnisaMyrtellari

    2016-01-01

    This work primarily addresses the design and implementation of a neural network based controller for the trajectory tracking of a differential drive mobile robot. The proposed control algorithm is an NN-based adaptive controller which tunes the gains of the back-stepping controller online according to the robot reference trajectory and its initial posture. In this method, a neural network is needed to learn the characteristics of the plant dynamics and make use of it to determine the future i...

  1. H∞ Based Control for Load Mitigation in Wind Turbines

    Directory of Open Access Journals (Sweden)

    Aron Pujana-Arrese

    2012-04-01

    Full Text Available This article demonstrates a strategy to design multivariable and multi-objective controllers based on the H∞ norm reduction applied to a wind turbine. The wind turbine model has been developed in the GH Bladed software and it is based on a 5 MW wind turbine defined in the Upwind European project. The designed control strategy works in the above rated power production zone and performs generator speed control and load reduction on the drive train and tower. In order to do this, two robust H∞ MISO (Multi-Input Single-Output controllers have been developed. These controllers generate collective pitch angle and generator torque set-point values to achieve the imposed control objectives. Linear models obtained in GH Bladed 4.0 are used, but the control design methodology can be used with linear models obtained from any other modelling package. Controllers are designed by setting out a mixed sensitivity problem, where some notch filters are also included in the controller dynamics. The obtained H∞ controllers have been validated in GH Bladed and an exhaustive analysis has been carried out to calculate fatigue load reduction on wind turbine components, as well as to analyze load mitigation in some extreme cases. The analysis compares the proposed control strategy based on H∞ controllers to a baseline control strategy designed using the classical control methods implemented on the present wind turbines.

  2. A New Approach for Controlling Chaos Based on Direct Optimizing Predictive Control

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    We introduce the predictive control theory into the study of chaos control and propose a direct optimizing predictive control algorithm based on a neural network model. The proposed control system stabilizes the chaotic motion in an unknown chaotic system onto the desired target trajectory. Compared with the existing similar algorithms, the proposed control system has faster response, so it requires much shorter time for the stabilization of the chaotic systems.The proposed approach can control hyperchaos and the algorithm is simple. The convergence of the control algorithm and the stability of the control system can be guaranteed. The theoretic analysis and simulations demonstrate the effectiveness of the algorithm.

  3. Implementation of neural network based non-linear predictive control

    DEFF Research Database (Denmark)

    Sørensen, Paul Haase; Nørgård, Peter Magnus; Ravn, Ole

    1999-01-01

    of non-linear systems. GPC is model based and in this paper we propose the use of a neural network for the modeling of the system. Based on the neural network model, a controller with extended control horizon is developed and the implementation issues are discussed, with particular emphasis...

  4. Dextran-based microspheres as controlled delivery systems for proteins

    NARCIS (Netherlands)

    Vlugt-Wensink, K.D.F.

    2007-01-01

    Dextran-based microspheres as controlled delivery systems for proteins Dextran based microspheres are investigated as controlled delivery system for proteins. Microspheres were prepared by polymerization of dex-HEMA in an aqueous two-phase system of dex-HEMA and PEG. Protein loaded microspheres are

  5. Vision-based control of the Manus using SIFT

    NARCIS (Netherlands)

    Liefhebber, F.; Sijs, J.

    2007-01-01

    The rehabilitation robot Manus is an assistive device for severely motor handicapped users. The executing of all day living tasks with the Manus, can be very complex and a vision-based controller can simplify this. The lack of existing vision-based controlled systems, is the poor reliability of the

  6. Control charts for location based on different sampling schemes

    NARCIS (Netherlands)

    Mehmood, R.; Riaz, M.; Does, R.J.M.M.

    2013-01-01

    Control charts are the most important statistical process control tool for monitoring variations in a process. A number of articles are available in the literature for the X̄ control chart based on simple random sampling, ranked set sampling, median-ranked set sampling (MRSS), extreme-ranked set

  7. Fault tolerant control based on active fault diagnosis

    DEFF Research Database (Denmark)

    Niemann, Hans Henrik

    2005-01-01

    An active fault diagnosis (AFD) method will be considered in this paper in connection with a Fault Tolerant Control (FTC) architecture based on the YJBK parameterization of all stabilizing controllers. The architecture consists of a fault diagnosis (FD) part and a controller reconfiguration (CR...

  8. Data-Based Predictive Control with Multirate Prediction Step

    Science.gov (United States)

    Barlow, Jonathan S.

    2010-01-01

    Data-based predictive control is an emerging control method that stems from Model Predictive Control (MPC). MPC computes current control action based on a prediction of the system output a number of time steps into the future and is generally derived from a known model of the system. Data-based predictive control has the advantage of deriving predictive models and controller gains from input-output data. Thus, a controller can be designed from the outputs of complex simulation code or a physical system where no explicit model exists. If the output data happens to be corrupted by periodic disturbances, the designed controller will also have the built-in ability to reject these disturbances without the need to know them. When data-based predictive control is implemented online, it becomes a version of adaptive control. One challenge of MPC is computational requirements increasing with prediction horizon length. This paper develops a closed-loop dynamic output feedback controller that minimizes a multi-step-ahead receding-horizon cost function with multirate prediction step. One result is a reduced influence of prediction horizon and the number of system outputs on the computational requirements of the controller. Another result is an emphasis on portions of the prediction window that are sampled more frequently. A third result is the ability to include more outputs in the feedback path than in the cost function.

  9. Genetic Algorithm based PID controller for Frequency Regulation Ancillary services

    Directory of Open Access Journals (Sweden)

    Sandeep Bhongade

    2010-12-01

    Full Text Available In this paper, the parameters of Proportional, Integral and Derivative (PID controller for Automatic Generation Control (AGC suitable in restructured power system is tuned according to Generic Algorithms (GAs based performance indices. The key idea of the proposed method is to use the fitness function based on Area Control Error (ACE. The functioning of the proposed Genetic Algorithm based PID (GAPID controller has been demonstrated on a 75-bus Indian power system network and the results have been compared with those obtained by using Least Square Minimization method.

  10. Quality guaranteed aggregation based model predictive control and stability analysis

    Institute of Scientific and Technical Information of China (English)

    LI DeWei; XI YuGeng

    2009-01-01

    The input aggregation strategy can reduce the online computational burden of the model predictive controller. But generally aggregation based MPC controller may lead to poor control quality. Therefore, a new concept, equivalent aggregation, is proposed to guarantee the control quality of aggregation based MPC. From the general framework of input linear aggregation, the design methods of equivalent aggregation are developed for unconstrained and terminal zero constrained MPC, which guarantee the actual control inputs exactly to be equal to that of the original MPC. For constrained MPC, quasi-equivalent aggregation strategies are also discussed, aiming to make the difference between the control inputs of aggregation based MPC and original MPC as small as possible. The stability conditions are given for the quasi-equivalent aggregation based MPC as well.

  11. A Novel Secondary Control for Microgrid Based on Synergetic Control of Multi-Agent System

    Directory of Open Access Journals (Sweden)

    Zhiwen Yu

    2016-03-01

    Full Text Available In power systems, the secondary control is a very useful way to restore the system frequency and voltage to the rated value. This paper tries to propose a secondary frequency and voltage control of islanded microgrids based on the distributed synergetic control of multi-agent systems. In the proposed control, since each distributed generation only requires its own information and that of the neighbors, the secondary control is fully distributed. The system is more reliable because the central controller and complex communication network are reduced in the distributed structure. Based on multi-agent systems, the dynamic model is established, and distributed synergetic control algorithms are given to design the secondary control of the islanded microgrid. Meanwhile, the system has globally asymptotic stability under the proposed control, which is proved by the direct Lyapunov method. Simulation results about a test microgrid are given to verify the effectiveness of the proposed control.

  12. PC-Based Applications Programming on the SRS Control System.

    Science.gov (United States)

    Martlew, Brian; Owen, Hywel; Pugh, Martin; Rawlinson, Bill; Smith, Susan

    1997-05-01

    The CERN PC-based ISOLDE control system has been installed at the SRS electron storage ring at Daresbury Laboratory. The use of Windows NT for the control consoles together with PC and VME front-end computers running under several operating systems has resulted in a flexible and reliable system for accelerator control. The implementation and philosophy of control application programs, based around a suite of Microsoft Visual Basic and Excel programs, is described. In particular, the use of Excel to provide adaptable programs online allows rapid generation of new control functions; orbit correction and servoing at the application level are described as examples of this.

  13. Attitude Optimal Backstepping Controller Based Quaternion for a UAV

    Directory of Open Access Journals (Sweden)

    Kaddouri Djamel

    2016-01-01

    Full Text Available A hierarchical controller design based on nonlinear H∞ theory and backstepping technique is developed for a nonlinear and coupled dynamic attitude system using conventional quaternion based method. The derived controller combines the attractive features of H∞ optimal controller and the advantages of the backstepping technique leading to a control law which avoids winding phenomena. Performance issues of the controller are illustrated in a simulation study made for a four-rotor vertical take-off and landing (VTOL aerial robot prototype known as the quadrotor aircraft.

  14. An experiment-based comparative study of fuzzy logic control

    Science.gov (United States)

    Berenji, Hamid R.; Chen, Yung-Yaw; Lee, Chuen-Chein; Murugesan, S.; Jang, Jyh-Shing

    1989-01-01

    An approach is presented to the control of a dynamic physical system through the use of approximate reasoning. The approach has been implemented in a program named POLE, and the authors have successfully built a prototype hardware system to solve the cartpole balancing problem in real-time. The approach provides a complementary alternative to the conventional analytical control methodology and is of substantial use when a precise mathematical model of the process being controlled is not available. A set of criteria for comparing controllers based on approximate reasoning and those based on conventional control schemes is furnished.

  15. Model-Based Development of Control Systems for Forestry Cranes

    Directory of Open Access Journals (Sweden)

    Pedro La Hera

    2015-01-01

    Full Text Available Model-based methods are used in industry for prototyping concepts based on mathematical models. With our forest industry partners, we have established a model-based workflow for rapid development of motion control systems for forestry cranes. Applying this working method, we can verify control algorithms, both theoretically and practically. This paper is an example of this workflow and presents four topics related to the application of nonlinear control theory. The first topic presents the system of differential equations describing the motion dynamics. The second topic presents nonlinear control laws formulated according to sliding mode control theory. The third topic presents a procedure for model calibration and control tuning that are a prerequisite to realize experimental tests. The fourth topic presents the results of tests performed on an experimental crane specifically equipped for these tasks. Results of these studies show the advantages and disadvantages of these control algorithms, and they highlight their performance in terms of robustness and smoothness.

  16. Behavior-Based Formation Control of Swarm Robots

    Directory of Open Access Journals (Sweden)

    Dongdong Xu

    2014-01-01

    Full Text Available Swarm robotics is a specific research field of multirobotics where a large number of mobile robots are controlled in a coordinated way. Formation control is one of the most challenging goals for the coordination control of swarm robots. In this paper, a behavior-based control design approach is proposed for two kinds of important formation control problems: efficient initial formation and formation control while avoiding obstacles. In this approach, a classification-based searching method for generating large-scale robot formation is presented to reduce the computational complexity and speed up the initial formation process for any desired formation. The behavior-based method is applied for the formation control of swarm robot systems while navigating in an unknown environment with obstacles. Several groups of experimental results demonstrate the success of the proposed approach. These methods have potential applications for various swarm robot systems in both the simulation and the practical environments.

  17. A modified Adaptive Wavelet PID Control Based on Reinforcement Learning for Wind Energy Conversion System Control

    Directory of Open Access Journals (Sweden)

    REZAZADEH, A.

    2010-05-01

    Full Text Available Nonlinear characteristics of wind turbines and electric generators necessitate complicated and nonlinear control of grid connected Wind Energy Conversion Systems (WECS. This paper proposes a modified self-tuning PID control strategy, using reinforcement learning for WECS control. The controller employs Actor-Critic learning in order to tune PID parameters adaptively. These Actor-Critic learning is a special kind of reinforcement learning that uses a single wavelet neural network to approximate the policy function of the Actor and the value function of the Critic simultaneously. These controllers are used to control a typical WECS in noiseless and noisy condition and results are compared with an adaptive Radial Basis Function (RBF PID control based on reinforcement learning and conventional PID control. Practical emulated results prove the capability and the robustness of the suggested controller versus the other PID controllers to control of the WECS. The ability of presented controller is tested by experimental setup.

  18. Organic Based Solar Cells with Morphology Control

    DEFF Research Database (Denmark)

    Andersen, Thomas Rieks

    The field of organic solar cells has in the last years gone through an impressive development with efficiencies reported up to 12 %. For organic solar cells to take the leap from primarily being a laboratory scale technology to being utilized as renewable energy source, several issues need...... to be addressed. Among these are a more direct transfer of new materials tested on a laboratory scale to large scale production than offered by spincoating, a method offering direct control of the morphology in the active layer, and a more environmental friendly processing, where the vast use of organic solvents...... offers a great challenge. In this thesis the development of inks with a pre-arranged morphology was attempted by two methods. First by grafting of silicon nanoparticles with an organic phenylene vinylene oligomer, the resulting particles were analyzed by 1H-NMR, absorption spectroscopy, Atomic Force...

  19. PQ Control Based Grid Connected DG Systems

    Directory of Open Access Journals (Sweden)

    P Siva Srinivas1 ,

    2015-10-01

    Full Text Available Distributed generation (DG generally refer to small scale electric power generators produce electricity that is bound to an electric distribution system. Distributed generation systems such as photovoltaic (PV or wind energy systems are parts of the future smart grids. By applying intelligent techniques these future grids change as smarter grids. During the past few years electrical energy consumption to the investment is increased when compared to cost on transmission and distribution resulting in compromised reliability and high energy costs. So there is need to change from conventional grid to smart grid. Micro grids consist of small power sources called distributed generation system. Many distributed generation systems such as photovoltaic systems are grid interfaced through power electronic voltage source inverters. In this paper a boost inverter technique is explained and distributed generation sources such as PV and fuel cell are connected in series with the help of PQ controller technique the above system is evaluated.

  20. An expert system based intelligent control scheme for space bioreactors

    Science.gov (United States)

    San, Ka-Yiu

    1988-01-01

    An expert system based intelligent control scheme is being developed for the effective control and full automation of bioreactor systems in space. The scheme developed will have the capability to capture information from various resources including heuristic information from process researchers and operators. The knowledge base of the expert system should contain enough expertise to perform on-line system identification and thus be able to adapt the controllers accordingly with minimal human supervision.

  1. The Redundant Arm Self-motion Control Based on Self-tuning Fuzzy PID Controller

    Institute of Scientific and Technical Information of China (English)

    Liu Yu(刘宇); Sun Lining; Du Zhijiang

    2004-01-01

    A fuzzy control algorithm based on self-tuning PID proportional factor is presented. To a certain degree, it overcomes robot motion control's nonlinearity and uncertainty caused by joints coupled and friction, and decreases overshoot of end manipulator's tracking desired curves. The controller's structure is very simple but effective. With this control method, a 7-DOF redundant arm's self-motion developed by the authors is investigated. Research results show that the said controller restrains track overshoot and possesses preferable merits.

  2. New Robust Nonlinear Controller Design Based on Predictive Control for Industrial Processes

    Directory of Open Access Journals (Sweden)

    Hossein Esfroghy

    2007-12-01

    Full Text Available In this paper a new sliding mode controller based on predictive control is used for the first order system, which is a good model for the industrial process. In this method a developed predictive control is used to optimize the sliding mode control including sliding surface and switching function coefficient at every moment. A new smooth function is used to reduce the chattering problems. Simulation results show the high effectiveness of the proposed controller.

  3. A complex control system based on the fuzzy PID control and state predictor feedback control

    Institute of Scientific and Technical Information of China (English)

    Zhengxi Li; Jie Liu; Dehui Sun; Rentao Zhao

    2004-01-01

    A multi-mode adaptive controller was proposed. The controller features in the combination of Bang-bang and Fuzzy PID controls with state predictor. When large error exists, the controller operates in Bang-bang mode, otherwise it works as a fuzzy PID controller. For only few parameters to be adjusted, the real time controlled system achieveed good stability and fast response. Furthermore, the introduction of state observer was also discussed to extend the capability of the proposed controller to the plant with time-delay factors. The classical PID controller and the multi-mode controller were applied to the same second-order system successively. By comparison of the simulation results, the effectiveness of the controller were shown. At last, on electric-wire production line, this approach was practiced to control electric-wire diameter with an additive random disturbance signal. The test result further proved the effectiveness of the multi-mode controller.

  4. PMSM Control System Based on Digital Signal Processor

    Directory of Open Access Journals (Sweden)

    Zhu Jun

    2013-04-01

    Full Text Available For the high power density of PMSM, designed the corresponding drive controller to improve the servo efficiency of PMSM servo system. According to the theory of math model of PMSM under the dq coordinate system, applied id = 0 vector control method as a PMSM control strategy, established PMSM controller model based on vector control. Taking DSP TMS320F2812 as controller core, built a power-driven circuit, control circuit and the main detection protection circuit. The algorithm of control program was completed on the hardware platform to present its software processes. The simulation results show that: the control system response is fast, can track the given speed and position quickly and accurately. The speed fluctuation, overshoot and steady state error are very small. The designed controller is reasonable, which has better dynamic and static characteristics, and be benefit to improve the efficiency of PMSM servo system.

  5. Control design for an autonomous wind based hydrogen production system

    Energy Technology Data Exchange (ETDEWEB)

    Valenciaga, F.; Evangelista, C.A. [CONICET, Laboratorio de Electronica Industrial Control e Instrumentacion (LEICI), Facultad de Ingenieria, Universidad Nacional de La Plata, CC.91, C.P. 1900, La Plata (Argentina)

    2010-06-15

    This paper presents a complete control scheme to efficiently manage the operation of an autonomous wind based hydrogen production system. This system comprises a wind energy generation module based on a multipolar permanent magnet synchronous generator, a lead-acid battery bank as short term energy storage and an alkaline von Hoerner electrolyzer. The control is developed in two hierarchical levels. The higher control level or supervisor control determines the general operation strategy for the whole system according to the wind conditions and the state of charge of the battery bank. On the other hand, the lower control level includes the individual controllers that regulate the respective module operation assuming the set-points determined by the supervisor control. These last controllers are approached using second-order super-twisting sliding mode techniques. The performance of the closed-loop system is assessed through representative computer simulations. (author)

  6. A Control Scheme Based on Online Delay Evaluation for a Class of Networked Control Systems

    Institute of Scientific and Technical Information of China (English)

    马向华; 谢剑英; 魏震

    2004-01-01

    A control scheme that integrates control technology with communication technology to solve the delay problem is introduced for a class of networked control systems: Networked Half-Link Systems (NHLS). Concretely, we use the master-slave clock synchronization technology to evaluate the delays online, and then the LQ optimal control based on delays is adopted to stabilize the controlled plant. During the clock synchronization process, the error of evaluated delays is inevitably induced from the clock synchronization error, which will deteriorate the system performances, and even make system unstable in certain cases. Hence, the discussions about the clock error, and the related control analysis and design are also developed. Specifically, we present the sufficient conditions of controller parameters that guarantee the system stability, and a controller design method based on the error of delays is addressed thereafter. The experiments based on a CANbus platform are fulfilled, and the experimental results verify the previous analytic results finally.

  7. Vision-based formation control of mobile robots

    Institute of Scientific and Technical Information of China (English)

    Shicai LIU; Dalong TAN; Guangjun LIU

    2005-01-01

    In this paper,a formation control algorithm and an obstacle avoidance control algorithm for mobile robots are developed based on a relative motion sensory system such as a pan/tilt camera vision system,without the need for global sensing and communication between robots.This is achieved by employing the velocity variation,instead of actual velocities,as the control inputs.Simulation and experimental results have demonstrated the effectiveness of the proposed control methods.

  8. Lyapunov-based control designs for flexible-link manipulators

    Science.gov (United States)

    Juang, Jer-Nan; Huang, Jen-Kuang; Yang, Li-Farn

    1989-01-01

    A feedback controller for the stabilization of closed-loop systems is proposed which is based on the Liapunov stability criterion. A feedback control law is first generated for the linear portion of the system equation using linear control theory. A feedback control is then designed for the nonlinear portion of the system equation by making negative the time derivative of a positive definite Liapunov function.

  9. CONTROL SCHEMES FOR CMAC NEURAL NETWORK-BASED VISUAL SERVOING

    Institute of Scientific and Technical Information of China (English)

    Wang Huaming; Xi Wenming; Zhu Jianying

    2003-01-01

    In IBVS (image based visual servoing), the error signal in image space should be transformed into the control signal in the input space quickly. To avoid the iterative adjustment and complicated inverse solution of image Jacobian, CMAC (cerebellar model articulation controller) neural network is inserted into visual servo control loop to implement the nonlinear mapping. Two control schemes are used. Simulation results on two schemes are provided, which show a better tracking precision and stability can be achieved using scheme 2.

  10. CONSTRUCTION COST INTEGRATED CONTROL BASED ON COMPUTER SIMULATION

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Construction cost control is a complex system engineering. Thetraditional controlling method cannot dynamically control in advance the construction cost because of its hysteresis. This paper proposes a computer simulation based construction cost integrated control method, which combines the cost with PERT systematically, so that the construction cost can be predicted and optimized systematically and effectively. The new method overcomes the hysteresis of the traditional systems, and is a distinct improvement over them in effect and practicality.

  11. Lyapunov-based control designs for flexible-link manipulators

    Science.gov (United States)

    Juang, Jer-Nan; Huang, Jen-Kuang; Yang, Li-Farn

    1989-01-01

    A feedback controller for the stabilization of closed-loop systems is proposed which is based on the Liapunov stability criterion. A feedback control law is first generated for the linear portion of the system equation using linear control theory. A feedback control is then designed for the nonlinear portion of the system equation by making negative the time derivative of a positive definite Liapunov function.

  12. Perti Net-Based Workflow Access Control Model

    Institute of Scientific and Technical Information of China (English)

    陈卓; 骆婷; 石磊; 洪帆

    2004-01-01

    Access control is an important protection mechanism for information systems. This paper shows how to make access control in workflow system. We give a workflow access control model (WACM) based on several current access control models. The model supports roles assignment and dynamic authorization. The paper defines the workflow using Petri net. It firstly gives the definition and description of the workflow, and then analyzes the architecture of the workflow access control model (WACM). Finally, an example of an e-commerce workflow access control model is discussed in detail.

  13. Engine control system having speed-based timing

    Science.gov (United States)

    Willi, Martin L [Dunlap, IL; Fiveland, Scott B [Metamora, IL; Montgomery, David T [Edelstein, IL; Gong, Weidong [Dunlap, IL

    2012-02-14

    A control system for an engine having a cylinder is disclosed having an engine valve movable to regulate a fluid flow of the cylinder and an actuator associated with the engine valve. The control system also has a controller in communication with the actuator. The controller is configured to receive a signal indicative of engine speed and compare the engine speed signal with a desired engine speed. The controller is also configured to selectively regulate the actuator to adjust a timing of the engine valve to control an amount of air/fuel mixture delivered to the cylinder based on the comparison.

  14. Model-based Control of a Bottom Fired Marine Boiler

    DEFF Research Database (Denmark)

    Solberg, Brian; Karstensen, Claus M. S.; Andersen, Palle;

    This paper focuses on applying model based MIMO control to minimize variations in water level for a specific boiler type. A first principles model is put up. The model is linearized and an LQG controller is designed. Furthermore the benefit of using a steam °ow measurement is compared to a strategy...... relying on estimates of the disturbance. Preliminary tests at the boiler system show that the designed controller is able to control the boiler process. Furthermore it can be concluded that relying on estimates of the steam flow in the control strategy does not decrease the controller performance...

  15. Model-based Control of a Bottom Fired Marine Boiler

    DEFF Research Database (Denmark)

    Solberg, Brian; Karstensen, Claus M. S.; Andersen, Palle;

    2005-01-01

    This paper focuses on applying model based MIMO control to minimize variations in water level for a specific boiler type. A first principles model is put up. The model is linearized and an LQG controller is designed. Furthermore the benefit of using a steam °ow measurement is compared to a strategy...... relying on estimates of the disturbance. Preliminary tests at the boiler system show that the designed controller is able to control the boiler process. Furthermore it can be concluded that relying on estimates of the steam flow in the control strategy does not decrease the controller performance...

  16. Power active filter control based on a resonant disturbance observer

    OpenAIRE

    Ramos Fuentes, German A.; Cortés Romero, John Alexander; Zou, Zhixiang; Costa Castelló, Ramon; Zhou, Keliang

    2015-01-01

    Active filters are power electronics devices used to eliminate harmonics from the distribution network. This article presents an active disturbance rejection control scheme for active filters. The controller is based on a linear disturbance observer combined with a disturbance rejection scheme. The parameter tuning is based on a combined pole placement and an optimal estimation based on Kalman-Bucy filter. Proposed scheme is validated through simulation and experimental work in an active filter.

  17. Research on fault-tolerant control of networked control systems based on information scheduling

    Institute of Scientific and Technical Information of China (English)

    Huo Zhihong; Zhang Zhixue; Fang Huajing

    2008-01-01

    A kind of networked control system is studied; the networked control system with noise disturbance is modeled based on information scheduling and control co-design.Augmented state matrix analysis method is introduced,and robust fault-tolerant control problem of networked control systems with noise disturbance under actuator failures is studied.The parametric expression of the controller under actuator failures is given.Furthermore,the result is analyzed by simulation tests,which not only satisfies the networked control systems stability,but also decreases the data information number in network channel and makes full use of the network resources.

  18. Development of a novel disturbance observer based fractional order PD controller for a gun control system.

    Science.gov (United States)

    Gao, Qiang; Zheng, Liang; Chen, Jilin; Wang, Li; Hou, Yuanlong

    2014-01-01

    Motion control of gun barrels is an ongoing topic for the development of gun control equipment (GCE) with excellent performances. In this paper, a novel disturbance observer (DOB) based fractional order PD (FOPD) control strategy is proposed for the GCE. By adopting the DOB, the control system behaves as if it were the nominal closed-loop system in the absence of disturbances and uncertainties. The optimal control parameters of the FOPD are determined from the loop-shaping perspective, and the Q-filter of the DOB is deliberately designed with consideration of system robustness. The linear frame of the proposed control system will enable the analysis process more convenient. The disturbance rejection properties and the tracking performances of the control system are investigated by both numerical and experimental tests, the results demonstrate that the proposed DOB based FOPD control system is of more robustness, and it is much more suitable for the gun control system with strong nonlinearity and disturbance.

  19. Enhanced PID Controllers Design Based on Modified Smith Predictor Control for Unstable Process with Time Delay

    Directory of Open Access Journals (Sweden)

    Chengqiang Yin

    2014-01-01

    Full Text Available A two-degree-of-freedom control structure is proposed for a class of unstable processes with time delay based on modified Smith predictor control; the superior performance of disturbance rejection and good robust stability are gained for the system. The set-point tracking controller is designed using the direct synthesis method; the IMC-PID controller for disturbance rejection is designed based on the internal mode control design principle. The controller for set-point response and the controller for disturbance rejection can be adjusted and optimized independently. Meanwhile, the two controllers are designed in the form of PID, which is convenient for engineering application. Finally, simulation examples demonstrate the validity of the proposed control scheme.

  20. Performance evaluation of sensor allocation algorithm based on covariance control

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    The covariance control capability of sensor allocation algorithms based on covariance control strategy is an important index to evaluate the performance of these algorithms. Owing to lack of standard performance metric indices to evaluate covariance control capability, sensor allocation ratio, etc, there are no guides to follow in the design procedure of sensor allocation algorithm in practical applications. To meet these demands, three quantified performance metric indices are presented, which are average covariance misadjustment quantity (ACMQ), average sensor allocation ratio (ASAR) and matrix metric influence factor (MMIF), where ACMQ, ASAR and MMIF quantify the covariance control capability, the usage of sensor resources and the robustness of sensor allocation algorithm, respectively. Meanwhile, a covariance adaptive sensor allocation algorithm based on a new objective function is proposed to improve the covariance control capability of the algorithm based on information gain. The experiment results show that the proposed algorithm have the advantage over the preceding sensor allocation algorithm in covariance control capability and robustness.

  1. Component-based Control Software Design for Flexible Manufacturing System

    Institute of Scientific and Technical Information of China (English)

    周炳海; 奚立峰; 曹永上

    2003-01-01

    A new method that designs and implements the component-based distributed & hierarchical flexible manufacturing control software is described with a component concept in this paper. The proposed method takes aim at improving the flexibility and reliability of the control system. On the basis of describing the concepts of component-based software and the distributed object technology, the architecture of the component-based software of the control system is suggested with the Common Object Request Broker Architecture (CORBA). And then, we propose a design method for component-based distributed & hierarchical flexible manufacturing control system. Finally, to verify the software design method, a prototype flexible manufacturing control system software has been implemented in Orbix 2. 3c, VC++6.0 and has been tested in connection with the physical flexible ranufacturing shop at the WuXi Professional Institute.

  2. Telescope Array Control System Based on Wireless Touch Screen Platform

    Science.gov (United States)

    Fu, X. N.; Huang, L.; Wei, J. Y.

    2016-07-01

    GWAC (Ground-based Wide Angle Cameras) are the ground-based observational instruments of the Sino-French cooperation SVOM (Space Variable Objects Monitor) astronomical satellite, and Mini-GWAC is a pathfinder and supplement of GWAC. In the context of the Mini-GWAC telescope array, this paper introduces the design and implementation of a kind of telescope array control system, which is based on wireless serial interface module to communicate. We describe the development and implementation of the system in detail in terms of control system principle, system hardware structure, software design, experiment, and test. The system uses the touch-control PC which is based on the Windows CE system as the upper-computer, the wireless transceiver module and PLC (Programmable Logic Controller) as the core. It has the advantages of low cost, reliable data transmission, and simple operation. So far, the control system has been applied to Mini-GWAC successfully.

  3. Transaction-Based Building Controls Framework, Volume 1: Reference Guide

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaram, Sriram [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Pratt, Robert G. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Akyol, Bora A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Fernandez, Nicholas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Foster, Nikolas AF [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Katipamula, Srinivas [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Mayhorn, Ebony T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Somani, Abhishek [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Steckley, Andrew C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Taylor, Zachary T. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

    2014-12-01

    This document proposes a framework concept to achieve the objectives of raising buildings’ efficiency and energy savings potential benefitting building owners and operators. We call it a transaction-based framework, wherein mutually-beneficial and cost-effective market-based transactions can be enabled between multiple players across different domains. Transaction-based building controls are one part of the transactional energy framework. While these controls realize benefits by enabling automatic, market-based intra-building efficiency optimizations, the transactional energy framework provides similar benefits using the same market -based structure, yet on a larger scale and beyond just buildings, to the society at large.

  4. Transaction-Based Building Controls Framework, Volume 1: Reference Guide

    Energy Technology Data Exchange (ETDEWEB)

    Somasundaram, Sriram; Pratt, Robert G.; Akyol, Bora A.; Fernandez, Nicholas; Foster, Nikolas AF; Katipamula, Srinivas; Mayhorn, Ebony T.; Somani, Abhishek; Steckley, Andrew C.; Taylor, Zachary T.

    2014-04-28

    This document proposes a framework concept to achieve the objectives of raising buildings’ efficiency and energy savings potential benefitting building owners and operators. We call it a transaction-based framework, wherein mutually-beneficial and cost-effective market-based transactions can be enabled between multiple players across different domains. Transaction-based building controls are one part of the transactional energy framework. While these controls realize benefits by enabling automatic, market-based intra-building efficiency optimizations, the transactional energy framework provides similar benefits using the same market -based structure, yet on a larger scale and beyond just buildings, to the society at large.

  5. Neural network based dynamic controllers for industrial robots.

    Science.gov (United States)

    Oh, S Y; Shin, W C; Kim, H G

    1995-09-01

    The industrial robot's dynamic performance is frequently measured by positioning accuracy at high speeds and a good dynamic controller is essential that can accurately compute robot dynamics at a servo rate high enough to ensure system stability. A real-time dynamic controller for an industrial robot is developed here using neural networks. First, an efficient time-selectable hidden layer architecture has been developed based on system dynamics localized in time, which lends itself to real-time learning and control along with enhanced mapping accuracy. Second, the neural network architecture has also been specially tuned to accommodate servo dynamics. This not only facilitates the system design through reduced sensing requirements for the controller but also enhances the control performance over the control architecture neglecting servo dynamics. Experimental results demonstrate the controller's excellent learning and control performances compared with a conventional controller and thus has good potential for practical use in industrial robots.

  6. Synthetical Control of AGC/LPC System Based on Neural Networks Internal Model Control

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    One synthetical control method of AGC/LPC system based on intelligence control theory-neural networks internal model control method is presented. Genetic algorithm (GA) is applied to optimize the parameters of the neural networks. Simulation results prove that this method is effective.

  7. Indirect Vector Control of an Induction Motor with Fuzzy-Logic based Speed Controller

    Directory of Open Access Journals (Sweden)

    BIROU, I.

    2010-02-01

    Full Text Available The aim of this paper is to present a new speed control structure for induction motors (IM by using fuzzy-logic based speed controllers. A fuzzy controller is designed to achieve fast dynamic response and robustness for low and high speeds. Different types of membership functions of the linguistic variables and output/input characteristics are analyzed. A simple but robust structure enables a wide range speed control of the driving system. The rotor flux field oriented control (FOC is realized by using a flux observer based on the IM model with nonlinear parameters. The control is extended to operate also in the field weakening region with an optimal rotor flux regulation. The control structure was implemented on a computer system, based on a fixed point digital signal processor (DSP. To verify the performances of the proposed driving system, simulated and experimental results are presented.

  8. Developments in model-based optimization and control distributed control and industrial applications

    CERN Document Server

    Grancharova, Alexandra; Pereira, Fernando

    2015-01-01

    This book deals with optimization methods as tools for decision making and control in the presence of model uncertainty. It is oriented to the use of these tools in engineering, specifically in automatic control design with all its components: analysis of dynamical systems, identification problems, and feedback control design. Developments in Model-Based Optimization and Control takes advantage of optimization-based formulations for such classical feedback design objectives as stability, performance and feasibility, afforded by the established body of results and methodologies constituting optimal control theory. It makes particular use of the popular formulation known as predictive control or receding-horizon optimization. The individual contributions in this volume are wide-ranging in subject matter but coordinated within a five-part structure covering material on: · complexity and structure in model predictive control (MPC); · collaborative MPC; · distributed MPC; · optimization-based analysis and desi...

  9. A Novel Control algorithm based DSTATCOM for Load Compensation

    Science.gov (United States)

    R, Sreejith; Pindoriya, Naran M.; Srinivasan, Babji

    2015-11-01

    Distribution Static Compensator (DSTATCOM) has been used as a custom power device for voltage regulation and load compensation in the distribution system. Controlling the switching angle has been the biggest challenge in DSTATCOM. Till date, Proportional Integral (PI) controller is widely used in practice for load compensation due to its simplicity and ability. However, PI Controller fails to perform satisfactorily under parameters variations, nonlinearities, etc. making it very challenging to arrive at best/optimal tuning values for different operating conditions. Fuzzy logic and neural network based controllers require extensive training and perform better under limited perturbations. Model predictive control (MPC) is a powerful control strategy, used in the petrochemical industry and its application has been spread to different fields. MPC can handle various constraints, incorporate system nonlinearities and utilizes the multivariate/univariate model information to provide an optimal control strategy. Though it finds its application extensively in chemical engineering, its utility in power systems is limited due to the high computational effort which is incompatible with the high sampling frequency in these systems. In this paper, we propose a DSTATCOM based on Finite Control Set Model Predictive Control (FCS-MPC) with Instantaneous Symmetrical Component Theory (ISCT) based reference current extraction is proposed for load compensation and Unity Power Factor (UPF) action in current control mode. The proposed controller performance is evaluated for a 3 phase, 3 wire, 415 V, 50 Hz distribution system in MATLAB Simulink which demonstrates its applicability in real life situations.

  10. Intelligent control based on intelligent characteristic model and its application

    Institute of Scientific and Technical Information of China (English)

    吴宏鑫; 王迎春; 邢琰

    2003-01-01

    This paper presents a new intelligent control method based on intelligent characteristic model for a kind of complicated plant with nonlinearities and uncertainties, whose controlled output variables cannot be measured on line continuously. The basic idea of this method is to utilize intelligent techniques to form the characteristic model of the controlled plant according to the principle of combining the char-acteristics of the plant with the control requirements, and then to present a new design method of intelli-gent controller based on this characteristic model. First, the modeling principles and expression of the intelligent characteristic model are presented. Then based on description of the intelligent characteristic model, the design principles and methods of the intelligent controller composed of several open-loops and closed-loops sub controllers with qualitative and quantitative information are given. Finally, the ap-plication of this method in alumina concentration control in the real aluminum electrolytic process is in-troduced. It is proved in practice that the above methods not only are easy to implement in engineering design but also avoid the trial-and-error of general intelligent controllers. It has taken better effect in the following application: achieving long-term stable control of low alumina concentration and increasing the controlled ratio of anode effect greatly from 60% to 80%.

  11. A Review of Router based Congestion Control Algorithms

    Directory of Open Access Journals (Sweden)

    Vandana Kushwaha

    2013-11-01

    Full Text Available This paper presents a study of Router based Congestion control approaches in wired network. As network is considered as a distributed system, any problem arises in such a system requires a distributed solution. Thus for good congestion control in the network we also need a solution distributed at source as well as router ends. The purpose of this study is to review the router based Congestion control research for wired network and characterize the different approaches to Congestion control design, by considering their advantages and limitations.

  12. Engine control system having fuel-based adjustment

    Science.gov (United States)

    Willi, Martin L.; Fiveland, Scott B.; Montgomery, David T.; Gong, Weidong

    2011-03-15

    A control system for an engine having a cylinder is disclosed having an engine valve configured to affect a fluid flow of the cylinder, an actuator configured to move the engine valve, and an in-cylinder sensor configured to generate a signal indicative of a characteristic of fuel entering the cylinder. The control system also has a controller in communication with the actuator and the sensor. The controller is configured to determine the characteristic of the fuel based on the signal and selectively regulate the actuator to adjust a timing of the engine valve based on the characteristic of the fuel.

  13. Cascaded process model based control: packed absorption column application.

    Science.gov (United States)

    Govindarajan, Anand; Jayaraman, Suresh Kumar; Sethuraman, Vijayalakshmi; Raul, Pramod R; Rhinehart, R Russell

    2014-03-01

    Nonlinear, adaptive, process-model based control is demonstrated in a cascaded single-input-single-output mode for pressure drop control in a pilot-scale packed absorption column. The process is shown to be nonlinear. Control is demonstrated in both servo and regulatory modes, for no wind-up in a constrained situation, and for bumpless transfer. Model adaptation is demonstrated and shown to provide process insight. The application procedure is revealed as a design guide to aid others in implementing process-model based control.

  14. Context-Based E-Health System Access Control Mechanism

    Science.gov (United States)

    Al-Neyadi, Fahed; Abawajy, Jemal H.

    E-Health systems logically demand a sufficiently fine-grained authorization policy for access control. The access to medical information should not be just role-based but should also include the contextual condition of the role to access data. In this paper, we present a mechanism to extend the standard role-based access control to incorporate contextual information for making access control decisions in e-health application. We present an architecture consisting of authorisation and context infrastructure that work cooperatively to grant access rights based on context-aware authorization policies and context information.

  15. Automobile Transmission Shift Control Based on MMAS and BP Networks

    Directory of Open Access Journals (Sweden)

    Jianxue Chen

    2013-08-01

    Full Text Available The neural network control model of automobile automatic transmission has been developed, which make the optimum shift decision based on the vehicle velocity, the vehicle acceleration and the throttle opening. The MAX-MIN ant syste (MMAS is introduced to train the neural network weights and thresholds. The basic theory and steps of MMAS algorithm are given, and applied in the automatic transmission shift control. Experimental results show that the automatic transmission shift control system based on MMAS, comparing to the system based on ACO-BP, has better capability of gear recognition, and can make shift decision promptly and effectively.

  16. Direct Torque Control of IPMSM to Improve Torque ripple and Efficiency based on Fuzzy Controller

    Directory of Open Access Journals (Sweden)

    B. Mirzaeian Dehkordi

    2012-09-01

    Full Text Available In this paper, a stator-flux-reference frame control method is proposed in order to control the speed and torque of an Interior Permanent Magnet Synchronous Machine (IPMSM in different loads condition. Direct Torque Control method (DTC based on Space Vector Modulation (SVM is used for control of IPMSM. In the proposed control method, conventional PI controller is used for controlling the stator flux, and torque of the motor. Also, a fuzzy controller is considered to improve the dynamic performance of DTC technique for speed control. In comparison to the conventional reference flux controller methods, this method, in addition, improves the torque profile of the motor drive. Moreover, it reduces copper losses. Simulation results for a 240V, 120A, 2500rpm, IPMSM confirm the appropriate performances of the method.

  17. The Overview of the National Ignition Facility Distributed Computer Control System

    Energy Technology Data Exchange (ETDEWEB)

    Lagin, L J; Bettenhausen, R C; Carey, R A; Estes, C M; Fisher, J M; Krammen, J E; Reed, R K; VanArsdall, P J; Woodruff, J P

    2001-10-15

    The Integrated Computer Control System (ICCS) for the National Ignition Facility (NIF) is a layered architecture of 300 front-end processors (FEP) coordinated by supervisor subsystems including automatic beam alignment and wavefront control, laser and target diagnostics, pulse power, and shot control timed to 30 ps. FEP computers incorporate either VxWorks on PowerPC or Solaris on UltraSPARC processors that interface to over 45,000 control points attached to VME-bus or PCI-bus crates respectively. Typical devices are stepping motors, transient digitizers, calorimeters, and photodiodes. The front-end layer is divided into another segment comprised of an additional 14,000 control points for industrial controls including vacuum, argon, synthetic air, and safety interlocks implemented with Allen-Bradley programmable logic controllers (PLCs). The computer network is augmented asynchronous transfer mode (ATM) that delivers video streams from 500 sensor cameras monitoring the 192 laser beams to operator workstations. Software is based on an object-oriented framework using CORBA distribution that incorporates services for archiving, machine configuration, graphical user interface, monitoring, event logging, scripting, alert management, and access control. Software coding using a mixed language environment of Ada95 and Java is one-third complete at over 300 thousand source lines. Control system installation is currently under way for the first 8 beams, with project completion scheduled for 2008.

  18. Implementation of EPICS based Control System for Radioisotope Beam line

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae-Ha; Ahn, Tae-Sung; Song, Young-Gi; Kwon, Hyeok-Jung; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Gyeongju (Korea, Republic of)

    2015-10-15

    Korea Mult-purpose Accelerator Complex (KOMAC) has been operating 100 MeV proton linear accelerator . For operating 100 MeV linac, various control system has been implemented such as vacuum, power supply, RCCS and etc. KOMAC is operating two beam lines so that clients can use 100 MeV proton beam for their experiment. KOMAC sends beam to beam line and target room using two dipole magnets and several quadrupole magnets. As demand for experiments and Radius Isotope using beam is increased, another beam line is under construction and RI beam line control system is need. To synchronize with KOMAC control system, RI beam line control system is based on Experimental Physics and Industrial control System (EPICS) software. The beam is transported to RI beam line to control magnet power supply and vacuum. Implementation of RI beam line control system is presented and some preliminary results are reported. The base RI beam line control system is implemented. It can control beam direction and vacuum. Comparing archived data and current data, RI beam line and control system will be improved. In the future, scroll pump and gate control system will be implemented using programmable logic controller PLC. RI beam interlock sequence will be added to KOMAC interlock system to protect linac.

  19. Internet Based Robot Control Using CORBA Based Communications

    Science.gov (United States)

    2009-12-01

    the Minister of National Defence, 2009 © Sa Majesté la Reine (en droit du Canada), telle que représentée par le ministre de la Défense nationale...interact with a service. Its lack of tools to support implementation is the main critique against it. 3.6.2 WSDL-based Web Services This type of Web...The main critiques against it are its complexity and loss of functionality of the “back” button and bookmarking ability for web browsers, though the

  20. Flow Control Strategy for the High Speed Network Based on Control Theory

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Design of an effective congestion control scheme is a hot topic in the development of computer network. The flow control scheme can adjust the packet sending rate in source host, thus effectively avoiding the network congestion. This paper proposes a new flow control scheme based on discrete control theory. The simulation results show that this method can adjust the sending rate and queue level in buffer rapidly and effectively. The method is easy to implement and applicable to high speed networks.

  1. A Design Approach for Controlled Self-Organization-Based Sensor Networks Focused on Control Timescale

    OpenAIRE

    2013-01-01

    Many researches on network control with a design principle of self-organization have been studied for large-scale networks. Since self-organized control is based on local interactions between system elements, it has high scalability, adaptability, and robustness; however, the management of the whole system is very difficult. In order to solve this problem, a controlled self-organization scheme has been proposed, which aims for desired system behavior by controlling a part of self-organized no...

  2. Pressure Control in Distillation Columns: A Model-Based Analysis

    DEFF Research Database (Denmark)

    Mauricio Iglesias, Miguel; Bisgaard, Thomas; Kristensen, Henrik

    2014-01-01

    A comprehensive assessment of pressure control in distillation columns is presented, including the consequences for composition control and energy consumption. Two types of representative control structures are modeled, analyzed, and benchmarked. A detailed simulation test, based on a real...... industrial distillation column, is used to assess the differences between the two control structures and to demonstrate the benefits of pressure control in the operation. In the second part of the article, a thermodynamic analysis is carried out to establish the influence of pressure on relative volatility...

  3. Observer-based H∞ control over packet dropping networks

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    A new controller design problem of networked control systems with packet dropping is proposed. Depending on the place that the observer is put in the system, the network control systems with packet dropping are modeled as stochastic systems with the random variables satisfying the Bernoulli random binary distribution. The observer-based controller is designed to stabilize the networked system in the sense of mean square, and the prescribed H∞ disturbance attenuation level is achieved. The controller design problem is formulated as the feasibility of the convex optimization problem, which can be solved by a linear matrix inequality (LMI) approach. Numerical examples illustrate the effectiveness of the proposed methods.

  4. System-Awareness for Agent-based Power System Control

    DEFF Research Database (Denmark)

    Heussen, Kai; Saleem, Arshad; Lind, Morten

    2010-01-01

    Operational intelligence in electric power systems is focused in a small number of control rooms that coordinate their actions. A clear division of responsibility and a command hierarchy organize system operation. With multi-agent based control systems, this control paradigm may be shifted...... to a more decentralized openaccess collaboration control paradigm. This shift cannot happen at once, but must fit also with current operation principles. In order to establish a scalable and transparent system control architecture, organizing principles have to be identified that allow for a smooth...

  5. Modified impedance control for robotic saw cutting: Simulation and implementation in three degrees of freedom

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.M. [Westinghouse Savannah River Co., Aiken, SC (United States); Reynolds, D.L.; Carroll, J.J.; Dawson, D.M. [Clemson Univ., SC (United States). School of Electrical and Computer Engineering

    1993-12-31

    The Savannah River Site (SRS) production and decommissioning operations produce solid radioactive transuranic (TRU) waste. This waste must be repackaged and sent to the Waste Isolation Pilot Plant (WIPP) for permanent disposal. The Savannah River Technology Center (SRTC) built a test facility to demonstrate simulated waste processing. The test facility use`s a CIMCORP multi-axis robot system, a CIMROC{trademark} II robot controller, and an electric circular saw to remotely open and size reduce plywood crates. The robot can either be teleoperated using joysticks or autonomously controlled via the, CIMROC{trademark} II. Both methods are inadequate for circular saw cutting of plywood crates due to frequent saw blade binding. Blade binding results from the current commercial robot controller limitations. The limitations are overcome by incorporating additional sensor information into the existing controller structure. In this paper we utilize a force sensor and a frequency counter to implement a modified impedance controller which prevents saw blade binding.

  6. Modified impedance control for robotic saw cutting: Simulation and implementation in three degrees of freedom

    Energy Technology Data Exchange (ETDEWEB)

    Kriikku, E.M. (Westinghouse Savannah River Co., Aiken, SC (United States)); Reynolds, D.L.; Carroll, J.J.; Dawson, D.M. (Clemson Univ., SC (United States). School of Electrical and Computer Engineering)

    1993-01-01

    The Savannah River Site (SRS) production and decommissioning operations produce solid radioactive transuranic (TRU) waste. This waste must be repackaged and sent to the Waste Isolation Pilot Plant (WIPP) for permanent disposal. The Savannah River Technology Center (SRTC) built a test facility to demonstrate simulated waste processing. The test facility use's a CIMCORP multi-axis robot system, a CIMROC[trademark] II robot controller, and an electric circular saw to remotely open and size reduce plywood crates. The robot can either be teleoperated using joysticks or autonomously controlled via the, CIMROC[trademark] II. Both methods are inadequate for circular saw cutting of plywood crates due to frequent saw blade binding. Blade binding results from the current commercial robot controller limitations. The limitations are overcome by incorporating additional sensor information into the existing controller structure. In this paper we utilize a force sensor and a frequency counter to implement a modified impedance controller which prevents saw blade binding.

  7. Emotional Learning Based Intelligent Controllers for Rotor Flux Oriented Control of Induction Motor

    Science.gov (United States)

    Abdollahi, Rohollah; Farhangi, Reza; Yarahmadi, Ali

    2014-08-01

    This paper presents design and evaluation of a novel approach based on emotional learning to improve the speed control system of rotor flux oriented control of induction motor. The controller includes a neuro-fuzzy system with speed error and its derivative as inputs. A fuzzy critic evaluates the present situation, and provides the emotional signal (stress). The controller modifies its characteristics so that the critics stress is reduced. The comparative simulation results show that the proposed controller is more robust and hence found to be a suitable replacement of the conventional PI controller for the high performance industrial drive applications.

  8. Sliding Mode Control Approach for Electrically Controllable Clutch of AMT Based on the Feedback Linearization

    Institute of Scientific and Technical Information of China (English)

    程东升; 张建武; 叶晓峰; 黄维纲

    2003-01-01

    A sliding mode control approach based on the feedback linearization is proposed for the electrically controllable clutch of AMT vehicles. The nonlinear dynamic model for the hydraulic actuator associated with clutch is established. By means of the exact feedback linearization procedure of differential geometry, an equivalent, fully controllable and linear model is derived via a homomorphic transformation for the AMT clutch system.Furthermore, a sliding mode control is introduced to improve robustness. The tracking tests are performed using the sliding mode control on a Santana LX passenger car, and the experimental results prove that this nonlinear controller is of fine robustness and high degree of tracking accuracy.

  9. Function-Based Access Control (FBAC): From Access Control Matrix to Access Control Tensor

    OpenAIRE

    Desmedt, Yvo; Shaghaghi, Arash

    2016-01-01

    Security researchers have stated that the core concept behind current implementations of access control predates the Internet. These assertions are made to pinpoint that there is a foundational gap in this field, and one should consider revisiting the concepts from the ground up. Moreover, Insider threats, which are an increasing threat vector against organizations are also associated with the failure of access control. Access control models derived from access control matrix encompass three ...

  10. SOFC temperature evaluation based on an adaptive fuzzy controller

    Institute of Scientific and Technical Information of China (English)

    Xiao-juan WU; Xin-jian ZHU; Guang-yi CAO; Heng-yong TU

    2008-01-01

    The operating temperature of a solid oxide fuel cell (SOFC) stack is a very important parameter to be controlled, which impacts the performance of the SOFC due to thermal cycling. In this paper, an adaptive fuzzy control method based on an affine nonlinear temperature model is developed to control the temperature of the SOFC within a specified range. Fuzzy logic systems are used to approximate nonlinear functions in the SOFC system and an adaptive technique is employed to construct the controller. Compared with the traditional fuzzy and proportion-integral-derivative (PID) control, the simulation results show that the designed adaptive fuzzy control method performed much better. So it is feasible to build an adaptive fuzzy controller for temperature control of the SOFC.

  11. Design of a FPGA based ABWR feedwater controller

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Hsuanhan; Chou, Hwaipwu; Lin, Chaung [Dept. of Institute of Nuclear Engineering and Science, National Tsing Hua University, Hsinchu (China)

    2012-05-15

    A feedwater controller targeted for an ABWR has been implemented using a modern field programmable gate array (FPGA), and verified using the full scope simulator at Taipower's Lungmen nuclear power station. The adopted control algorithm is a rule-based fuzzy logic. Point to point validation of the FPGA circuit board has been executed using a digital pattern generator. The simulation model of the simulator was employed for verification and validation of the controller design under various plant initial conditions. The transient response and the steady state tracking ability were evaluated and showed satisfactory results. The present work has demonstrated that the FPGA based approach incorporated with a rule-based fuzzy logic control algorithm is a flexible yet feasible approach for feedwater controller design in nuclear power plant applications.

  12. Design of A FPGA Based ABWR Feedwater Controller

    Energy Technology Data Exchange (ETDEWEB)

    Huang, Hsuan Han; Chou, Hwai Pwu; Lin, Chaung [National Tsing Hua University, Hsinchu (China)

    2011-08-15

    A feedwater controller for the Taipower's Lungmen nuclear power station has been implemented using the modern field programmable gate array (FPGA) and verified using a full scope engineering simulator. The adopted control algorithm is a rule-based fuzzy logic. Point to point validation of the FPGA circuit board has been executed using a digital pattern generator. The simulator was employed for the verification and validation of the controller design with various plant initial conditions. The transient response and the steady state tracking ability were evaluated and showed satisfactory results. The present work has demonstrated that the FPGA based approach incorporated with a rule-based fuzzy control algorithm is a flexible yet feasible approach for controller design in nuclear power plant applications.

  13. A reinforcement learning-based architecture for fuzzy logic control

    Science.gov (United States)

    Berenji, Hamid R.

    1992-01-01

    This paper introduces a new method for learning to refine a rule-based fuzzy logic controller. A reinforcement learning technique is used in conjunction with a multilayer neural network model of a fuzzy controller. The approximate reasoning based intelligent control (ARIC) architecture proposed here learns by updating its prediction of the physical system's behavior and fine tunes a control knowledge base. Its theory is related to Sutton's temporal difference (TD) method. Because ARIC has the advantage of using the control knowledge of an experienced operator and fine tuning it through the process of learning, it learns faster than systems that train networks from scratch. The approach is applied to a cart-pole balancing system.

  14. Task Delegation Based Access Control Models for Workflow Systems

    Science.gov (United States)

    Gaaloul, Khaled; Charoy, François

    e-Government organisations are facilitated and conducted using workflow management systems. Role-based access control (RBAC) is recognised as an efficient access control model for large organisations. The application of RBAC in workflow systems cannot, however, grant permissions to users dynamically while business processes are being executed. We currently observe a move away from predefined strict workflow modelling towards approaches supporting flexibility on the organisational level. One specific approach is that of task delegation. Task delegation is a mechanism that supports organisational flexibility, and ensures delegation of authority in access control systems. In this paper, we propose a Task-oriented Access Control (TAC) model based on RBAC to address these requirements. We aim to reason about task from organisational perspectives and resources perspectives to analyse and specify authorisation constraints. Moreover, we present a fine grained access control protocol to support delegation based on the TAC model.

  15. Remote control of microcontroller-based infant stimulating system.

    Science.gov (United States)

    Burunkaya, M; Güler, I

    2000-04-01

    In this paper, a remote-controlled and microcontroller-based cradle is designed and constructed. This system is also called Remote Control of Microcontroller-Based Infant Stimulation System or the RECOMBIS System. Cradle is an infant stimulating system that provides relaxation and sleeping for the baby. RECOMBIS system is designed for healthy full-term newborns to provide safe infant care and provide relaxation and sleeping for the baby. A microcontroller-based electronic circuit was designed and implemented for RECOMBIS system. Electromagnets were controlled by 8-bit PIC16F84 microcontroller, which is programmed using MPASM package. The system works by entering preset values from the keyboard, or pulse code modulated radio frequency remote control system. The control of the system and the motion range were tested. The test results showed that the system provided a good performance.

  16. Motion control simulation based on VR for humanoid robot

    Science.gov (United States)

    He, Huaiqing; Tang, Haoxuan

    2004-03-01

    This paper describes the motion control simulation based on VR for humanoid robot aiming at walking and running. To insure that the motion rhythm of humanoid robot conforms to the motion laws of humans, the body geometrical model based on skeleton and its kinematics models based on the graph of time sequences are presented firstly. Then a control algorithm based on Jacobian matrix is proposed to generate the periodical walking and running. Finally, computer simulation experiments demonstrate the feasibility of the models and the algorithm. The simulation system developed makes us interactively regulate the motion direction and velocity for humanoid robot.

  17. Agent Based Control of Electric Power Systems with Distributed Generation

    DEFF Research Database (Denmark)

    Saleem, Arshad

    . Situation in Denmark is even more interesting, with a current 20% penetration of wind energy it is moving towards an ambitious goal of 50% penetration by the year 2050. Realization of these concepts requires that power systems should be of distributed nature { consisting of autonomous components...... agents. It suggests a multiagent based exible control architecture (subgrid control) suitable for the implementation of the innovative control concepts. This subgrid control architecture is tested on a novel distributed software platform which has been developed to design, test and evaluate distributed...... control strategies. The results have been discussed from case studies of multiagent based distributed control scenarios in electric power systems. The main contribution of this work is a proposal for system design methodology for application of intelligent agent technology in power systems...

  18. On feasibility of regional frequency-based emergency control plans

    Energy Technology Data Exchange (ETDEWEB)

    Bevrani, H. [Department of Electrical and Computer Engineering, University of Kurdistan, Sanandaj, P.O. Box 416 (Iran); Ledwich, G.; Ford, J.J. [School of Engineering Systems, Queensland University of Technology, Brisbane, Qld 4001 (Australia); Dong, Z.Y. [Department of Electrical Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon (China)

    2009-07-15

    Decentralized and regional load-frequency control of power systems operating in normal and near-normal conditions has been well studied; and several analysis/synthesis approaches have been developed during the last few decades. However in contingency and off-normal conditions, the existing emergency control plans, such as under-frequency load shedding, are usually applied in a centralized structure using a different analysis model. This paper discusses the feasibility of using frequency-based emergency control schemes based on tie-line measurements and local information available within a control area. The conventional load-frequency control model is generalized by considering the dynamics of emergency control/protection schemes and an analytic approach to analyze the regional frequency response under normal and emergency conditions is presented. (author)

  19. Response Based Emergency Control System for Power System Transient Stability

    Directory of Open Access Journals (Sweden)

    Huaiyuan Wang

    2015-11-01

    Full Text Available A transient stability control system for the electric power system composed of a prediction method and a control method is proposed based on trajectory information. This system, which is independent of system parameters and models, can detect the transient stability of the electric power system quickly and provide the control law when the system is unstable. Firstly, system instability is detected by the characteristic concave or convex shape of the trajectory. Secondly, the control method is proposed based on the analysis of the slope of the state plane trajectory when the power system is unstable. Two control objectives are provided according to the methods of acquiring the far end point: one is the minimal cost to restore the system to a stable state; the other one is the minimal cost to limit the maximum swing angle. The simulation indicates that the mentioned transient stability control system is efficient.

  20. PID Controller Design Based on the Time Domain Information of Robust IMC Controller Using Maximum Sensitivity

    Institute of Scientific and Technical Information of China (English)

    JIN Qibing; LIU Qie; WANG Qi; TIAN Yuqi; WANG Yuanfei

    2013-01-01

    The IMC (Internal Model Control) controller based on robust tuning can improve the robustness and dynamic performance of the system.In this paper,the robustness degree of the control system is investigated based on Maximum Sensitivity (Ms) in depth.And the analytical relationship is obtained between the robustness specification and controller parameters,which gives a clear design criterion to robust IMC controller.Moreover,a novel and simple IMC-PID (Proportional-Integral-Derivative) tuning method is proposed by converting the IMC controller to PID form in terms of the time domain rather than the frequency domain adopted in some conventional IMC-based methods.Hence,the presented IMC-PID gives a good performance with a specific robustness degree.The new IMC-PID method is compared with other classical IMC-PID rules,showing the flexibility and feasibility for a wide range of plants.

  1. Optimal control based on adaptive model reduction approach to control transfer phenomena

    Science.gov (United States)

    Oulghelou, Mourad; Allery, Cyrille

    2017-01-01

    The purpose of optimal control is to act on a set of parameters characterizing a dynamical system to achieve a target dynamics. In order to reduce CPU time and memory storage needed to perform control on evolution systems, it is possible to use reduced order models (ROMs). The mostly used one is the Proper Orthogonal Decomposition (POD). However the bases constructed in this way are sensitive to the configuration of the dynamical system. Consequently, the need of full simulations to build a basis for each configuration is time consuming and makes that approach still relatively expensive. In this paper, to overcome this difficulty we suggest to use an adequate bases interpolation method. It consists in computing the associated bases to a distribution of control parameters. These bases are afterwards called in the control algorithm to build a reduced basis adapted to a given control parameter. This interpolation method involves results of the calculus of Geodesics on Grassmann manifold.

  2. Fault tolerant control based on interval type-2 fuzzy sliding mode controller for coaxial trirotor aircraft.

    Science.gov (United States)

    Zeghlache, Samir; Kara, Kamel; Saigaa, Djamel

    2015-11-01

    In this paper, a robust controller for a Six Degrees of Freedom (6 DOF) coaxial trirotor helicopter control is proposed in presence of defects in the system. A control strategy based on the coupling of the interval type-2 fuzzy logic control and sliding mode control technique are used to design a controller. The main purpose of this work is to eliminate the chattering phenomenon and guaranteeing the stability and the robustness of the system. In order to achieve this goal, interval type-2 fuzzy logic control has been used to generate the discontinuous control signal. The simulation results have shown that the proposed control strategy can greatly alleviate the chattering effect, and perform good reference tracking in presence of defects in the system.

  3. Fault diagnosis and fault-tolerant control based on adaptive control approach

    CERN Document Server

    Shen, Qikun; Shi, Peng

    2017-01-01

    This book provides recent theoretical developments in and practical applications of fault diagnosis and fault tolerant control for complex dynamical systems, including uncertain systems, linear and nonlinear systems. Combining adaptive control technique with other control methodologies, it investigates the problems of fault diagnosis and fault tolerant control for uncertain dynamic systems with or without time delay. As such, the book provides readers a solid understanding of fault diagnosis and fault tolerant control based on adaptive control technology. Given its depth and breadth, it is well suited for undergraduate and graduate courses on linear system theory, nonlinear system theory, fault diagnosis and fault tolerant control techniques. Further, it can be used as a reference source for academic research on fault diagnosis and fault tolerant control, and for postgraduates in the field of control theory and engineering. .

  4. Switching Control of Wind Turbine Sub-Controllers Based on an Active Disturbance Rejection Technique

    Directory of Open Access Journals (Sweden)

    Yancai Xiao

    2016-10-01

    Full Text Available Wind power generation systems require complex control systems with multiple working conditions and multiple controllers. Under different operating conditions, switching without disturbancebetweenthesub-controllersplaysacriticalroleinensuringthestabilityofpowersystems. The sub-controllers of two typical cases in the permanent magnet direct drive (PMDD wind turbine running process are studied, one is the proportional integral (PI controller in the maximum power points tracking (MPPT stage, the other is the fuzzy pitch angle controller in the constant power stage. The switching strategy of the two sub-controllers is the emphasis in this research. Based on the active disturbance rejection control (ADRC, the switching mode of the sub-controllers is proposed, which can effectively restrain the sudden changes of the rotor current during the switching process, and improve the quality of power generation. The feasibility and effectiveness of the sub-controller switching strategy is verified by Matlab/Simulink simulation for a 2 MW PMDD wind turbine.

  5. Speed Control System on Marine Diesel Engine Based on a Self-Tuning Fuzzy PID Controller

    Directory of Open Access Journals (Sweden)

    Naeim Farouk

    2012-03-01

    Full Text Available The degree of speed control of ship machinery effects on the economics and optimization of the machinery configuration and operation. All marine vessel ranging need some sort of speed control system to control and govern the speed of the marine diesel engines. This study presents a self-tuning fuzzy PID control system for speed control system of marine diesel engine. The system under consideration is a fourth-order plant with highly dynamic and uncertain environments. The current speed controllers for marine/traction diesel engines based on PID Controller cannot fully handle the uncertainties associated with such dynamic environments. A fuzzy logic control algorithm is used to estimate the PID coefficients in order to handle such uncertainties to produce a better control performance. Simulation tests were established using Simulink of MATLAB. The obtained results have demonstrated the feasibility and effectiveness of the proposed approach. Simulation results are represented in this study.

  6. Predictive functional control based on fuzzy T-S model for HVAC systems temperature control

    Institute of Scientific and Technical Information of China (English)

    Hongli L(U); Lei JIA; Shulan KONG; Zhaosheng ZHANG

    2007-01-01

    In heating,ventilating and air-conditioning(HVAC)systems,there exist severe nonlinearity,time-varying nature,disturbances and uncertainties.A new predictive functional control based on Takagi-Sugeno(T-S)fuzzy model was proposed to control HVAC systems.The T-S fuzzy model of stabilized controlled process was obtained using the least squares method,then on the basis of global linear predictive model from T-S fuzzy model,the process was controlled by the predictive functional controller.Especially the feedback regulation part was developed to compensate uncertainties of fuzzy predictive model.Finally simulation test results in HVAC systems control applications showed that the proposed fuzzy model predictive functional control improves tracking effect and robustness.Compared with the conventional PID controller,this control strategy has the advantages of less overshoot and shorter setting time,etc.

  7. Research on an Urban Traffic Control System Based on DGPS

    Institute of Scientific and Technical Information of China (English)

    张锦; 张姝慧; 曹继红

    2002-01-01

    The basic principles of GPS (Global Positioning System) and DGPS (Differential GPS) are described. The principle and structure of vehicle navigation systems, and its application to the urban traffic flow guidance are analyzed. Then, an area-coordinated adaptive control system based on DGPS and a traffic flow guidance information system based on DGPS are put forward, and their working principles and functions are researched. This is to provides a new way for the development of urban road traffic control systems.

  8. The Integrated Control-Mechanism in ATM-Based Networks

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Survivability is one of the important issues in ATM-based networks since even a single network element failure may cause a serious data loss. This paper introduces a new restoration mechanism based on multi-layer ATM survivable network management architecture. This mechanism integrates the general control and restoration control by establishing the Working VPs logical network, Backup VPs logical network and spare logical network in order to optimally utilize the network resources while maintaining the restoration requirements.

  9. Efficient Quantum Private Communication Based on Dynamic Control Code Sequence

    Science.gov (United States)

    Cao, Zheng-Wen; Feng, Xiao-Yi; Peng, Jin-Ye; Zeng, Gui-Hua; Qi, Jin

    2016-12-01

    Based on chaos and quantum properties, we propose a quantum private communication scheme with dynamic control code sequence. The initial sequence is obtained via chaotic systems, and the control code sequence is derived by grouping, XOR and extracting. A shift cycle algorithm is designed to enable the dynamic change of control code sequence. Analysis shows that transmission efficiency could reach 100 % with high dynamics and security.

  10. Switch Reluctance Motor Control Based on Fuzzy Logic System

    Directory of Open Access Journals (Sweden)

    S. Aleksandrovsky

    2012-01-01

    Full Text Available Due to its intrinsic simplicity and reliability, the switched reluctance motor (SRM has now become a promising candidate for variable-speed drive applications as an alternative induction motor in various industrial application. However, the SRM has the disadvantage of nonlinear characteristic and control. It is suggested to use controller based on fuzzy logic system. Design of FLS controller and simulation model presented.

  11. Efficient Quantum Private Communication Based on Dynamic Control Code Sequence

    Science.gov (United States)

    Cao, Zheng-Wen; Feng, Xiao-Yi; Peng, Jin-Ye; Zeng, Gui-Hua; Qi, Jin

    2017-04-01

    Based on chaos and quantum properties, we propose a quantum private communication scheme with dynamic control code sequence. The initial sequence is obtained via chaotic systems, and the control code sequence is derived by grouping, XOR and extracting. A shift cycle algorithm is designed to enable the dynamic change of control code sequence. Analysis shows that transmission efficiency could reach 100 % with high dynamics and security.

  12. Decoupling Control Method Based on Neural Network for Missiles

    Institute of Scientific and Technical Information of China (English)

    ZHAN Li; LUO Xi-shuang; ZHANG Tian-qiao

    2005-01-01

    In order to make the static state feedback nonlinear decoupling control law for a kind of missile to be easy for implementation in practice, an improvement is discussed. The improvement method is to introduce a BP neural network to approximate the decoupling control laws which are designed for different aerodynamic characteristic points, so a new decoupling control law based on BP neural network is produced after the network training. The simulation results on an example illustrate the approach obtained feasible and effective.

  13. Fuzzy control of power converters based on quasilinear modelling

    Science.gov (United States)

    Li, C. K.; Lee, W. L.; Chou, Y. W.

    1995-03-01

    Unlike feedback control by the fuzzy PID method, a new fuzzy control algorithm based on quasilinear modelling of the DC-DC converter is proposed. Investigation is carried out using a buck-boost converter. Simulation results demonstrated that the converter can be regulated with improved performance even when subjected to input disturbance and load variation.

  14. FPGA based Control of a Production Cell System

    NARCIS (Netherlands)

    Groothuis, Marcel A.; Zuijlen, van Jasper J.P.; Broenink, Jan F.

    2008-01-01

    Most motion control systems for mechatronic systems are implemented on digital computers. In this paper we present an FPGA based solution implemented on a low cost Xilinx Spartan III FPGA. A Production Cell setup with multiple parallel operating units is chosen as a test case. The embedded control s

  15. Model Predictive Control based on Finite Impulse Response Models

    DEFF Research Database (Denmark)

    Prasath, Guru; Jørgensen, John Bagterp

    2008-01-01

    We develop a regularized l2 finite impulse response (FIR) predictive controller with input and input-rate constraints. Feedback is based on a simple constant output disturbance filter. The performance of the predictive controller in the face of plant-model mismatch is investigated by simulations...

  16. The Abstract Machine Model for Transaction-based System Control

    Energy Technology Data Exchange (ETDEWEB)

    Chassin, David P.

    2003-01-31

    Recent work applying statistical mechanics to economic modeling has demonstrated the effectiveness of using thermodynamic theory to address the complexities of large scale economic systems. Transaction-based control systems depend on the conjecture that when control of thermodynamic systems is based on price-mediated strategies (e.g., auctions, markets), the optimal allocation of resources in a market-based control system results in an emergent optimal control of the thermodynamic system. This paper proposes an abstract machine model as the necessary precursor for demonstrating this conjecture and establishes the dynamic laws as the basis for a special theory of emergence applied to the global behavior and control of complex adaptive systems. The abstract machine in a large system amounts to the analog of a particle in thermodynamic theory. The permit the establishment of a theory dynamic control of complex system behavior based on statistical mechanics. Thus we may be better able to engineer a few simple control laws for a very small number of devices types, which when deployed in very large numbers and operated as a system of many interacting markets yields the stable and optimal control of the thermodynamic system.

  17. MAS Based Event-Triggered Hybrid Control for Smart Microgrids

    DEFF Research Database (Denmark)

    Dou, Chunxia; Liu, Bin; Guerrero, Josep M.

    2013-01-01

    This paper is focused on an advanced control for autonomous microgrids. In order to improve the performance regarding security and stability, a hierarchical decentralized coordinated control scheme is proposed based on multi-agents structure. Moreover, corresponding to the multi-mode and the hybr...

  18. Agent-Based Decentralized Control Method for Islanded Microgrids

    DEFF Research Database (Denmark)

    Li, Qiang; Chen, Feixiong; Chen, Minyou;

    2016-01-01

    In this paper, an agent-based decentralized control model for islanded microgrids is proposed, which consists of a two-layer control structure. The bottom layer is the electrical distribution microgrid, while the top layer is the communication network composed of agents. An agent is regarded as a...

  19. Connected Dominating Set Based Topology Control in Wireless Sensor Networks

    Science.gov (United States)

    He, Jing

    2012-01-01

    Wireless Sensor Networks (WSNs) are now widely used for monitoring and controlling of systems where human intervention is not desirable or possible. Connected Dominating Sets (CDSs) based topology control in WSNs is one kind of hierarchical method to ensure sufficient coverage while reducing redundant connections in a relatively crowded network.…

  20. Model-Based Traffic Control for Sustainable Mobility

    NARCIS (Netherlands)

    Zegeye, S.K.

    2011-01-01

    Computationally efficient dynamic fuel consumption, emissions, and dispersion of emissions models are developed. Fast and practically feasible model-based controller is proposed. Using the developed models, the controller steers the traffic flow in such a way that a balanced trade-off between the t

  1. Ruled-based control of off-grid electrolysis

    DEFF Research Database (Denmark)

    Serna, A.; Tadeo, F.; Normey-Rico, J. E.

    2016-01-01

    This work deals with a ruled-based control strategy to produce hydrogen from wind and wave energy in an offshore platform. These renewable energies feed a set of alkaline electrolyzers that produce H2. The proposed control system allows regulating the operation of the electrolyzers, taking into a...

  2. Route-Based Control of Hybrid Electric Vehicles: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Gonder, J. D.

    2008-01-01

    Today's hybrid electric vehicle controls cannot always provide maximum fuel savings over all drive cycles. Route-based controls could improve HEV fuel efficiency by 2%-4% and help save nearly 6.5 million gallons of fuel annually.

  3. Internet-Based Treatment for Insomnia: A Controlled Evaluation

    Science.gov (United States)

    Strom, Lars; Pettersson, Richard; Andersson, Gerhard

    2004-01-01

    This study investigated the effects of an Internet-based intervention for insomnia. Participants who met criteria for insomnia (N = 109) were randomly assigned to either a cognitive-behavioral self-help treatment or a waiting list control condition. The 5-week intervention mainly consisted of sleep restriction, stimulus control, and cognitive…

  4. A Direct Feedback Control Based on Fuzzy Recurrent Neural Network

    Institute of Scientific and Technical Information of China (English)

    李明; 马小平

    2002-01-01

    A direct feedback control system based on fuzzy-recurrent neural network is proposed, and a method of training weights of fuzzy-recurrent neural network was designed by applying modified contract mapping genetic algorithm. Computer simul ation results indicate that fuzzy-recurrent neural network controller has perfect dynamic and static performances .

  5. Adaptive Feature Based Control of Compact Disk Players

    DEFF Research Database (Denmark)

    Odgaard, Peter Fogh; Stoustrup, Jakob; Vidal, Enrique Sanchez

    2005-01-01

    of the Compact Disc. The problem is to design servo controllers which are well suited for handling surface faults which disturb the position measurement and still react sufficiently against normal disturbances like mechanical shocks. In previous work of the same authors a feature based control scheme for CD...

  6. Connected Dominating Set Based Topology Control in Wireless Sensor Networks

    Science.gov (United States)

    He, Jing

    2012-01-01

    Wireless Sensor Networks (WSNs) are now widely used for monitoring and controlling of systems where human intervention is not desirable or possible. Connected Dominating Sets (CDSs) based topology control in WSNs is one kind of hierarchical method to ensure sufficient coverage while reducing redundant connections in a relatively crowded network.…

  7. Prediction based chaos control via a new neural network

    Energy Technology Data Exchange (ETDEWEB)

    Shen Liqun [School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin 150001 (China)], E-mail: liqunshen@gmail.com; Wang Mao [Space Control and Inertia Technology Research Center, Harbin Institute of Technology, Harbin 150001 (China); Liu Wanyu [School of Electrical Engineering and Automation, Harbin Institute of Technology, Harbin 150001 (China); Sun Guanghui [Space Control and Inertia Technology Research Center, Harbin Institute of Technology, Harbin 150001 (China)

    2008-11-17

    In this Letter, a new chaos control scheme based on chaos prediction is proposed. To perform chaos prediction, a new neural network architecture for complex nonlinear approximation is proposed. And the difficulty in building and training the neural network is also reduced. Simulation results of Logistic map and Lorenz system show the effectiveness of the proposed chaos control scheme and the proposed neural network.

  8. Robust observer-based adaptive fuzzy sliding mode controller

    Science.gov (United States)

    Oveisi, Atta; Nestorović, Tamara

    2016-08-01

    In this paper, a new observer-based adaptive fuzzy integral sliding mode controller is proposed based on the Lyapunov stability theorem. The plant is subjected to a square-integrable disturbance and is assumed to have mismatch uncertainties both in state- and input-matrices. Based on the classical sliding mode controller, the equivalent control effort is obtained to satisfy the sufficient requirement of sliding mode controller and then the control law is modified to guarantee the reachability of the system trajectory to the sliding manifold. In order to relax the norm-bounded constrains on the control law and solve the chattering problem of sliding mode controller, a fuzzy logic inference mechanism is combined with the controller. An adaptive law is then introduced to tune the parameters of the fuzzy system on-line. Finally, for evaluating the controller and the robust performance of the closed-loop system, the proposed regulator is implemented on a real-time mechanical vibrating system.

  9. Computer control of the SMC polarized target

    Science.gov (United States)

    Le Goff, J.-M.; Azoulay, R.; Berglund, P.; Dulya, C.; Gournay, J. F.; Hayashi, N.; Kyynäräinen, J.; Magnon, A.; Matichard, G.; Niinikoski, T. O.; Trentalange, S.

    1995-02-01

    The SMC polarized target is controlled through VME crates driven by CPUs working under the VxWorks operating system. The CPUs are connected to a SUN workstation which provides the user interface due to a graphical package named SL-GMS. This results in user friendliness, high modularity and flexibility. The system allows the control of: (1) the superconductive solenoid and the transverse dipole: control of the power supplies; automatic reversal of the spin direction by field rotation; acquisition, display and storage of the electric and cryogenic parameters; generation of alarms; and (2) the dilution refrigerator: evaporator level control; acquisition, display and storage of ≈ 100 cryogenic parameters; and generation of alarms.

  10. A Fuzzy Logic Based Supervisory Hierarchical Control Scheme for Real Time Pressure Control

    Institute of Scientific and Technical Information of China (English)

    N.Kanagaraj; P.Sivashanmugam; S.Paramasivam

    2009-01-01

    This paper describes a supervisory hierarchical fuzzy controller (SHFC) for regulating pressure in a real-time pilot pressure control system.The input scaling factor tuning of a direct expert controller is made using the error and process input parameters in a closed loop system in order to obtain better controller performance for set-point change and load disturbances.This on-line tuning method reduces operator involvement and enhances the controller performance to a wide operating range.The hierarchical control scheme consists of an intelligent upper level supervisory fuzzy controller and a lower level direct fuzzy controller.The upper level controller provides a mechanism to the main goal of the system and the lower level controller delivers the solutions to a particular situation. The control algorithm for the proposed scheme has been developed and tested using an ARM7 microcontroller-based embedded target board for a nonlinear pressure process having dead time.To demonstrate the effectiveness,the results of the proposed hierarchical controller,fuzzy controller and conventional proportional-integral (PI) controller are analyzed.The results prove that the SHFC performance is better in terms of stability and robustness than the conventional control methods.

  11. Development of a Simulink/RTW-Based Realtime Control System for an Induction Motor Vector Control

    Energy Technology Data Exchange (ETDEWEB)

    Kang, M. H. [Sunmoon University, Chonan (Korea)

    2001-03-01

    In this research a Simulink/RTW-based realtime control system was developed for an induction motor vector control. On the Simulink window, the control system is designed in the form of block diagrams, program codes are produced automatically with the RTW(Real Time Workshop), then an DSP c compiles the program codes. With this automatic program producing method rapid prototyping is realized with the least time-consuming manual programming procedures. To show effectiveness of the proposed system designing scheme a DSP-based induction motor vector controller was constructed and implemented. (author). 10 refs., 15 figs., 2 tabs.

  12. Computer control for the CERN ISOLDE-3 project

    Energy Technology Data Exchange (ETDEWEB)

    Lustig, H.D.; Benincasa, G.P.; Richard-Serre, C.

    1987-05-01

    ISOLDE-3 has been designed for fully integrated computer control from the beginning. Budget and manpower limitations required that we should use already existing CERN equipment to a large extent, both on the hardware and software side. A CAMAC integrated, multi-processor computer system (based on the Motorola 68000) with serial CAMAC transmission has been chosen. To ease programming by nonspecialists the interpretive language NODAL is extensively used. The control system has three consoles, each one driven by a 'mother crate' containing the microprocessors, the modules for the user interactions and the peripherals. For the time being there are no links between the 3 single-user, single-task systems. The criteria for the distribution of the various tasks are therefore to put in the same loop only systems which do not need simultaneous control. Particular emphasis was put on standardisation: all similar elements are controlled by the same hardware modules and standard software packages allow easy modifications and extensions.

  13. Disturbance observer based hierarchical control of coaxial-rotor UAV.

    Science.gov (United States)

    Mokhtari, M Rida; Cherki, Brahim; Braham, Amal Choukchou

    2017-03-01

    This paper propose an hierarchical controller based on a new disturbance observer with finite time convergence (FTDO) to solve the path tracking of a small coaxial-rotor-typs Unmanned Aerial Vehicles (UAVs) despite of unknown aerodynamic efforts. The hierarchical control technique is used to separate the flight control problem into an inner loop that controls attitude and an outer loop that controls the thrust force acting on the vehicle. The new disturbance observer with finite time convergence is intergated to online estimate the unknown uncertainties and disturbances and to actively compensate them in finite time.The analysis further extends to the design of a control law that takes the disturbance estimation procedure into account. Numerical simulations are carried out to demonstrate the efficiency of the proposed control strategy.

  14. Iterative learning control of SOFC based on ARX identification model

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    This paper presents an application of iterative learning control (ILC) technique to the voltage control of solid oxide fuel cell (SOFC) stack. To meet the demands of the control system design, an autoregressive model with exogenous input (ARX) is established. Firstly, by regulating the variation of the hydrogen flow rate proportional to that of the current, the fuel utilization of the SOFC is kept within its admissible range. Then, based on the ARX model, three kinds of ILC controllers, i.e. P-, PI- and PD-type are designed to keep the voltage at a desired level. Simulation results demonstrate the potential of the ARX model applied to the control of the SOFC, and prove the excellence of the ILC controllers for the voltage control of the SOFC.

  15. Generalized ESO and Predictive Control Based Robust Autopilot Design

    Directory of Open Access Journals (Sweden)

    Bhavnesh Panchal

    2016-01-01

    Full Text Available A novel continuous time predictive control and generalized extended state observer (GESO based acceleration tracking pitch autopilot design is proposed for a tail controlled, skid-to-turn tactical missile. As the dynamics of missile are significantly uncertain with mismatched uncertainty, GESO is employed to estimate the state and uncertainty in an integrated manner. The estimates are used to meet the requirement of state and to robustify the output tracking predictive controller designed for nominal system. Closed loop stability for the controller-observer structure is established. An important feature of the proposed design is that it does not require any specific information about the uncertainty. Also the predictive control design yields the feedback control gain and disturbance compensation gain simultaneously. Effectiveness of GESO in estimation of the states and uncertainties and in robustifying the predictive controller in the presence of parametric uncertainties, external disturbances, unmodeled dynamics, and measurement noise is illustrated by simulation.

  16. Transient stability improvement by nonlinear controllers based on tracking

    Energy Technology Data Exchange (ETDEWEB)

    Ramirez, Juan M. [Centro de Investigacion y Estudios Avanzados, Guadalajara, Mexico. Av. Cientifica 1145. Col. El Bajio. Zapopan, Jal. 45015 (Mexico); Arroyave, Felipe Valencia; Correa Gutierrez, Rosa Elvira [Universidad Nacional de Colombia, Sede Medellin. Facultad de Minas, Escuela de Mecatronica (Colombia)

    2011-02-15

    This paper deals with the control problem in multi-machine electric power systems, which represent complex great scale nonlinear systems. Thus, the controller design is a challenging problem. These systems are subjected to different perturbations, such as short circuits, connection and/or disconnection of loads, lines, or generators. Then, the utilization of controllers which guarantee good performance under those perturbations is required in order to provide electrical energy to the loads with admissible stability margins. The proposed controllers are based on a systematic strategy, which calculate nonlinear controllers for generating units in a power plant, both for voltage and velocity regulation. The formulation allows designing controllers in a multi-machine power system without intricate calculations. Results on a power system of the open research indicate the proposition's suitability. The problem is formulated as a tracking problem. The designed controllers may be implemented in any electric power system. (author)

  17. Information fusion based optimal control for large civil aircraft system.

    Science.gov (United States)

    Zhen, Ziyang; Jiang, Ju; Wang, Xinhua; Gao, Chen

    2015-03-01

    Wind disturbance has a great influence on landing security of Large Civil Aircraft. Through simulation research and engineering experience, it can be found that PID control is not good enough to solve the problem of restraining the wind disturbance. This paper focuses on anti-wind attitude control for Large Civil Aircraft in landing phase. In order to improve the riding comfort and the flight security, an information fusion based optimal control strategy is presented to restrain the wind in landing phase for maintaining attitudes and airspeed. Data of Boeing707 is used to establish a nonlinear mode with total variables of Large Civil Aircraft, and then two linear models are obtained which are divided into longitudinal and lateral equations. Based on engineering experience, the longitudinal channel adopts PID control and C inner control to keep longitudinal attitude constant, and applies autothrottle system for keeping airspeed constant, while an information fusion based optimal regulator in the lateral control channel is designed to achieve lateral attitude holding. According to information fusion estimation, by fusing hard constraint information of system dynamic equations and the soft constraint information of performance index function, optimal estimation of the control sequence is derived. Based on this, an information fusion state regulator is deduced for discrete time linear system with disturbance. The simulation results of nonlinear model of aircraft indicate that the information fusion optimal control is better than traditional PID control, LQR control and LQR control with integral action, in anti-wind disturbance performance in the landing phase. Copyright © 2014 ISA. Published by Elsevier Ltd. All rights reserved.

  18. Control of a Buoyancy-Based Pilot Underwater Lifting Body

    Directory of Open Access Journals (Sweden)

    Finn Haugen

    2010-04-01

    Full Text Available This paper is about position control of a specific small-scale pilot underwater lifting body where the lifting force stems from buoyancy adjusted with an air pocket in the lifting body. A mathematical model is developed to get a basis for a simulator which is used for testing and for designing the control system, including tuning controller parameters. A number of different position controller solutions were tried both on a simulator and on the physical system. Successful control on both the simulator and the physical system was obtained with cascade control based on feedback from measured position and height of the air pocket in the lifting body. The primary and the secondary controllers of the cascade control system were tuned using Skogestad's model-based PID tuning rules. Feedforward from estimated load force was implemented in combination with the cascade control system, giving a substantial improvement of the position control system, both with varying position reference and varying disturbance (load mass.

  19. An Extended Role Based Access Control Method for XML Documents

    Institute of Scientific and Technical Information of China (English)

    MENG Xiao-feng; LUO Dao-feng; OU Jian-bo

    2004-01-01

    As XML has been increasingly important as the Data-change format of Internet and Intranet, access-control-on-XML-properties rises as a new issue.Role-based access control (RBAC) is an access control method that has been widely used in Internet, Operation System and Relation Data Base these 10 years.Though RBAC is already relatively mature in the above fields, new problems occur when it is used in XML properties.This paper proposes an integrated model to resolve these problems, after the fully analysis on the features of XML and RBAC.

  20. Electroencephalography (EEG) Based Control in Assistive Mobile Robots: A Review

    Science.gov (United States)

    Krishnan, N. Murali; Mariappan, Muralindran; Muthukaruppan, Karthigayan; Hijazi, Mohd Hanafi Ahmad; Kitt, Wong Wei

    2016-03-01

    Recently, EEG based control in assistive robot usage has been gradually increasing in the area of biomedical field for giving quality and stress free life for disabled and elderly people. This study reviews the deployment of EGG based control in assistive robots, especially for those who in need and neurologically disabled. The main objective of this paper is to describe the methods used for (i) EEG data acquisition and signal preprocessing, (ii) feature extraction and (iii) signal classification methods. Besides that, this study presents the specific research challenges in the designing of these control systems and future research directions.

  1. Digital controlling for GMA welding machine based on DSP

    Institute of Scientific and Technical Information of China (English)

    华学明; 吴毅雄; 张勇; 焦馥杰; 于乾波

    2003-01-01

    This paper introduced a welding machine for GMAW using digital controlling method based on DSP (Digital Signal Process). By means of flexible programming according to welding technologies and experiences the suitable characteristics of welding machine, such as line compensation, welding voltage and current feedback, wire-feed driving, SCR trigging and so on, can be controlled and self-adjusted using digital signals. Through the designing based on DSP it is put out that the traditional hardware of control circuit is decreased greatly which can enhance the stability and reliability of welding machine. Finally, the welding experiment using CO2 shielding gas proves that the welding process is stable.

  2. Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup—The hardware, firmware, and software implementation

    Science.gov (United States)

    Antony, Joby; Mathuria, D. S.; Datta, T. S.; Maity, Tanmoy

    2015-12-01

    The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as "CADS," which stands for "Complete Automation of Distribution System." CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN (Local

  3. Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup--The hardware, firmware, and software implementation.

    Science.gov (United States)

    Antony, Joby; Mathuria, D S; Datta, T S; Maity, Tanmoy

    2015-12-01

    The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as "CADS," which stands for "Complete Automation of Distribution System." CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN (Local

  4. Development of intelligent instruments with embedded HTTP servers for control and data acquisition in a cryogenic setup—The hardware, firmware, and software implementation

    Energy Technology Data Exchange (ETDEWEB)

    Antony, Joby; Mathuria, D. S.; Datta, T. S. [Inter University Accelerator Centre, Aruna Asaf Ali Marg, New Delhi 110067 (India); Maity, Tanmoy [Department of MME, Indian School of Mines (ISM), Dhanbad 826004 (India)

    2015-12-15

    The power of Ethernet for control and automation technology is being largely understood by the automation industry in recent times. Ethernet with HTTP (Hypertext Transfer Protocol) is one of the most widely accepted communication standards today. Ethernet is best known for being able to control through internet from anywhere in the globe. The Ethernet interface with built-in on-chip embedded servers ensures global connections for crate-less model of control and data acquisition systems which have several advantages over traditional crate-based control architectures for slow applications. This architecture will completely eliminate the use of any extra PLC (Programmable Logic Controller) or similar control hardware in any automation network as the control functions are firmware coded inside intelligent meters itself. Here, we describe the indigenously built project of a cryogenic control system built for linear accelerator at Inter University Accelerator Centre, known as “CADS,” which stands for “Complete Automation of Distribution System.” CADS deals with complete hardware, firmware, and software implementation of the automated linac cryogenic distribution system using many Ethernet based embedded cryogenic instruments developed in-house. Each instrument works as an intelligent meter called device-server which has the control functions and control loops built inside the firmware itself. Dedicated meters with built-in servers were designed out of ARM (Acorn RISC (Reduced Instruction Set Computer) Machine) and ATMEL processors and COTS (Commercially Off-the-Shelf) SMD (Surface Mount Devices) components, with analog sensor front-end and a digital back-end web server implementing remote procedure call over HTTP for digital control and readout functions. At present, 24 instruments which run 58 embedded servers inside, each specific to a particular type of sensor-actuator combination for closed loop operations, are now deployed and distributed across control LAN

  5. Adaptive Sliding Mode Control Method Based on Nonlinear Integral Sliding Surface for Agricultural Vehicle Steering Control

    Directory of Open Access Journals (Sweden)

    Taochang Li

    2014-01-01

    Full Text Available Automatic steering control is the key factor and essential condition in the realization of the automatic navigation control of agricultural vehicles. In order to get satisfactory steering control performance, an adaptive sliding mode control method based on a nonlinear integral sliding surface is proposed in this paper for agricultural vehicle steering control. First, the vehicle steering system is modeled as a second-order mathematic model; the system uncertainties and unmodeled dynamics as well as the external disturbances are regarded as the equivalent disturbances satisfying a certain boundary. Second, a transient process of the desired system response is constructed in each navigation control period. Based on the transient process, a nonlinear integral sliding surface is designed. Then the corresponding sliding mode control law is proposed to guarantee the fast response characteristics with no overshoot in the closed-loop steering control system. Meanwhile, the switching gain of sliding mode control is adaptively adjusted to alleviate the control input chattering by using the fuzzy control method. Finally, the effectiveness and the superiority of the proposed method are verified by a series of simulation and actual steering control experiments.

  6. Kinect-Based Sliding Mode Control for Lynxmotion Robotic Arm

    Directory of Open Access Journals (Sweden)

    Ismail Ben Abdallah

    2016-01-01

    Full Text Available Recently, the technological development of manipulator robot increases very quickly and provides a positive impact to human life. The implementation of the manipulator robot technology offers more efficiency and high performance for several human’s tasks. In reality, efforts published in this context are focused on implementing control algorithms with already preprogrammed desired trajectories (passive robots case or trajectory generation based on feedback sensors (active robots case. However, gesture based control robot can be considered as another channel of system control which is not widely discussed. This paper focuses on a Kinect-based real-time interactive control system implementation. Based on LabVIEW integrated development environment (IDE, a developed human-machine-interface (HMI allows user to control in real time a Lynxmotion robotic arm. The Kinect software development kit (SDK provides a tool to keep track of human body skeleton and abstract it into 3-dimensional coordinates. Therefore, the Kinect sensor is integrated into our control system to detect the different user joints coordinates. The Lynxmotion dynamic has been implemented in a real-time sliding mode control algorithm. The experimental results are carried out to test the effectiveness of the system, and the results verify the tracking ability, stability, and robustness.

  7. Boiler level control system based on ControlLogix5550 PLC

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>This paper is a research design based on EFPT process control device.In the design,actual industry field has been simulated and corresponding modelling has been carried on for the boiler level system.Then the appropriate PID parameter has been sorted out and ControlLogix5550 PLC has been used to control the entire boiler level system. At last,a corresponding control interface has been established and the boiler level has been under a safe and accurate control.

  8. Tensor Product Model Transformation Based Adaptive Integral-Sliding Mode Controller: Equivalent Control Method

    Directory of Open Access Journals (Sweden)

    Guoliang Zhao

    2013-01-01

    Full Text Available This paper proposes new methodologies for the design of adaptive integral-sliding mode control. A tensor product model transformation based adaptive integral-sliding mode control law with respect to uncertainties and perturbations is studied, while upper bounds on the perturbations and uncertainties are assumed to be unknown. The advantage of proposed controllers consists in having a dynamical adaptive control gain to establish a sliding mode right at the beginning of the process. Gain dynamics ensure a reasonable adaptive gain with respect to the uncertainties. Finally, efficacy of the proposed controller is verified by simulations on an uncertain nonlinear system model.

  9. Tensor product model transformation based adaptive integral-sliding mode controller: equivalent control method.

    Science.gov (United States)

    Zhao, Guoliang; Sun, Kaibiao; Li, Hongxing

    2013-01-01

    This paper proposes new methodologies for the design of adaptive integral-sliding mode control. A tensor product model transformation based adaptive integral-sliding mode control law with respect to uncertainties and perturbations is studied, while upper bounds on the perturbations and uncertainties are assumed to be unknown. The advantage of proposed controllers consists in having a dynamical adaptive control gain to establish a sliding mode right at the beginning of the process. Gain dynamics ensure a reasonable adaptive gain with respect to the uncertainties. Finally, efficacy of the proposed controller is verified by simulations on an uncertain nonlinear system model.

  10. DSP Based Vector Control of Five-Phase Induction Using Fuzzy Logic Control

    Directory of Open Access Journals (Sweden)

    Zakaria Mohamed Salem

    2012-03-01

    Full Text Available Abstract - This paper proposes an indirect field oriented controller for five-phase induction motor drives. The controller is based on fuzzy logic control technique. Simulation is carried out by using the Matlab/Simulink package. A complete control system experimentally implemented using digital signal processing (DSP board. The performance of the proposed system is investigated at different operating conditions. The proposed controller is robust and suitable to high performance five-phase induction motor drives. Simulation and experimental results validate the proposed approaches.

  11. Support Vector Machine-Based Nonlinear System Modeling and Control

    Institute of Scientific and Technical Information of China (English)

    张浩然; 韩正之; 冯瑞; 于志强

    2003-01-01

    This paper provides an introduction to a support vector machine, a new kernel-based technique introduced in statistical learning theory and structural risk minimization, then presents a modeling-control framework based on SVM.At last a numerical experiment is taken to demonstrate the proposed approach's correctness and effectiveness.

  12. Multi-axis control based on movement control cards in NC systems

    Science.gov (United States)

    Jiang, Tingbiao; Wei, Yunquan

    2005-12-01

    Today most movement control cards need special control software of topper computers and are only suitable for fixed-axis controls. Consequently, the number of axes which can be controlled is limited. Advanced manufacture technology develops at a very high speed, and that development brings forth. New requirements for movement control in mechanisms and electronics. This paper introduces products of the 5th generation of movement control cards, PMAC 2A-PC/104, made by the Delta Tau Company in the USA. Based on an analysis of PMAC 2A-PC/104, this paper first describes two aspects relevant to the hardware structure of movement control cards and the interrelated software of the topper computers. Then, two methods are presented for solving these problems. The first method is to set limit switches on the movement control cards; all of them can be used to control each moving axis. The second method is to program applied software with existing programming language (for example, VC ++, Visual Basic, Delphi, and so forth). This program is much easier to operate and expand by its users. By using a limit switch, users can choose different axes in movement control cards. Also, users can change parts of the parameters in the control software of topper computers to realize different control axes. Combining these 2 methods proves to be convenient for realizing multi-axis control in numerical control systems.

  13. Interline power flow controller (IPFC) based damping recurrent neural network controllers for enhancing stability

    Energy Technology Data Exchange (ETDEWEB)

    Banaei, M.R., E-mail: m.banaei@azaruniv.ed [Electrical Engineering Department, Faculty of Engineering, Azarbaijan University of Tarbiat Moallem, Tabriz (Iran, Islamic Republic of); Kami, A. [Electrical Engineering Department, Faculty of Engineering, Azarbaijan University of Tarbiat Moallem, Tabriz (Iran, Islamic Republic of)

    2011-07-15

    Highlights: {yields} A method is presented to improve power system stability using IPFC. {yields} Recurrent neural network controllers damp oscillations in a power system. {yields} Training is based on back propagation with adaptive training parameters. {yields} Selection of effectiveness damping control signal carried out using SVD method. -- Abstract: This paper presents a method to improve power system stability using IPFC based damping online learning recurrent neural network controllers for damping oscillations in a power system. Parameters of equipped controllers for enhancing dynamical stability at the IPFC are tuned using mathematical methods. Therefore these control parameters are often fixed and are set for particular system configurations or operating points. Multilayer recurrent neural network, which can be tuned for changing system conditions, is used in this paper for effectively damp the oscillations. Training is based on back propagation with adaptive training parameters. This controller is tested to variations in system loading and fault in the power system and its performance is compared with performance of a controller that the phase compensation method is used to set its parameters. Selection of effectiveness damping control signal for the design of robust IPFC damping controller carried out through singular value decomposition (SVD) method. Simulation studies show the superior robustness and stabilizing effect of the proposed controller in comparison with phase compensation method.

  14. A Substractive Clustering Based Fuzzy Hybrid Reference Control Design for Transient Response Improvement of PID Controller

    Directory of Open Access Journals (Sweden)

    Endra Joelianto

    2009-11-01

    Full Text Available The well known PID controller has inherent limitations in fulfilling simultaneously the conflicting control design objectives. Parameters of the tuned PID controller should trade off the requirement of tracking set-point performances, disturbance rejection and stability robustness. Combination of hybrid reference control (HRC with PID controller results in the transient response performances can be independently achieved without deteriorating the disturbance rejection properties and the stability robustness requirement. This paper proposes a fuzzy based HRC where the membership functions of the fuzzy logic system are obtained by using a substractive clustering technique. The proposed method guarantees the transient response performances satisfaction while preserving the stability robustness of the closed loop system controlled by the PID controller with effective and systematic procedures in designing the fuzzy hybrid reference control system.

  15. Adaptive Backstepping Controller Design for Leveling Control of an Underwater Platform Based on Joint Space

    Directory of Open Access Journals (Sweden)

    Zhi-Lin Zeng

    2014-01-01

    Full Text Available This paper focuses on high precision leveling control of an underwater heavy load platform, which is viewed as an underwater parallel robot on the basis of its work pattern. The kinematic of platform with deformation is analyzed and the dynamics model of joint space is established. An adaptive backstepping controller according to Lyapunov's function is proposed for leveling control of platform based on joint space. Furthermore, the “lowest point fixed angle error” leveling scheme called “chase” is chosen for leveling control of platform. The digital simulation and practical experiment of single joint space actuator are carried out, and the results show high precision servo control of joint space. On the basis of this, the platform leveling control simulation relies on the hardware-in-loop system. The results indicate that the proposed controller can effectively restrain the influence from system parameter uncertainties and external disturbance to realize high precision leveling control of the underwater platform.

  16. Composite disturbance rejection control based on generalized extended state observer.

    Science.gov (United States)

    Zhang, Yanjun; Zhang, Jun; Wang, Lu; Su, Jianbo

    2016-07-01

    Traditional extended state observer (ESO) design method does not focus on analysis of system reconstruction strategy. The prior information of the controlled system cannot be used for ESO implementation to improve the control accuracy. In this paper, composite disturbance rejection control strategy is proposed based on generalized ESO. First, the disturbance rejection performance of traditional ESO is analyzed to show the essence of the reconstruction strategy. Then, the system is reconstructed based on the equivalent disturbance model. The generalized ESO is proposed based on the reconstructed model, while convergence of the proposed ESO is analyzed along with the outer loop feedback controller. Simulation results on a second order mechanical system show that the proposed generalized ESO can deal with the external disturbance with known model successfully. Experiment of attitude tracking task on an aircraft is also carried out to show the effectiveness of the proposed method. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

  17. Passivity-based control and estimation in networked robotics

    CERN Document Server

    Hatanaka, Takeshi; Fujita, Masayuki; Spong, Mark W

    2015-01-01

    Highlighting the control of networked robotic systems, this book synthesizes a unified passivity-based approach to an emerging cross-disciplinary subject. Thanks to this unified approach, readers can access various state-of-the-art research fields by studying only the background foundations associated with passivity. In addition to the theoretical results and techniques,  the authors provide experimental case studies on testbeds of robotic systems  including networked haptic devices, visual robotic systems,  robotic network systems and visual sensor network systems. The text begins with an introduction to passivity and passivity-based control together with the other foundations needed in this book. The main body of the book consists of three parts. The first examines how passivity can be utilized for bilateral teleoperation and demonstrates the inherent robustness of the passivity-based controller against communication delays. The second part emphasizes passivity’s usefulness for visual feedback control ...

  18. Global Observer-Based Attitude Controller Using Direct Inertial Measurements

    Directory of Open Access Journals (Sweden)

    Saâdi Bouhired

    2014-04-01

    Full Text Available In this work, we address the problem of global attitude control using direct inertial measurements. When using direct inertial measurement to observe the rigid body attitude, it is shown that due to a geometrical obstruction, it is impossible to achieve global asymptotic stability. In fact, for a particular initial condition the tracking error quaternion converges to a pure imaginary quaternion formed by an eigenvector of a characteristic matrix related to the inertial constant and known vectors. Our proposition consists of adding a dynamic signal to force the rigid body to escape from such a situation. The proposed observer-based controller is synthesized based on a single Lyapunov function and a stability analysis shows that the controller stabilizes globally and asymptotically the rigid body attitude at the desired one. The effectiveness of the proposed observer-based controller is confirmed by simulation results.

  19. Event-Based control of depth of hypnosis in anesthesia.

    Science.gov (United States)

    Merigo, Luca; Beschi, Manuel; Padula, Fabrizio; Latronico, Nicola; Paltenghi, Massimiliano; Visioli, Antonio

    2017-08-01

    In this paper, we propose the use of an event-based control strategy for the closed-loop control of the depth of hypnosis in anesthesia by using propofol administration and the bispectral index as a controlled variable. A new event generator with high noise-filtering properties is employed in addition to a PIDPlus controller. The tuning of the parameters is performed off-line by using genetic algorithms by considering a given data set of patients. The effectiveness and robustness of the method is verified in simulation by implementing a Monte Carlo method to address the intra-patient and inter-patient variability. A comparison with a standard PID control structure shows that the event-based control system achieves a reduction of the total variation of the manipulated variable of 93% in the induction phase and of 95% in the maintenance phase. The use of event based automatic control in anesthesia yields a fast induction phase with bounded overshoot and an acceptable disturbance rejection. A comparison with a standard PID control structure shows that the technique effectively mimics the behavior of the anesthesiologist by providing a significant decrement of the total variation of the manipulated variable. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. A Model of Workflow-oriented Attributed Based Access Control

    Directory of Open Access Journals (Sweden)

    Guoping Zhang

    2011-02-01

    Full Text Available the emergence of “Internet of Things” breaks previous traditional thinking, which integrates physical infrastructure and network infrastructure into unified infrastructure. There will be a lot of resources or information in IoT, so computing and processing of information is the core supporting of IoT. In this paper, we introduce “Service-Oriented Computing” to solve the problem where each device can offer its functionality as standard services. Here we mainly discuss the access control issue of service-oriented computing in Internet of Things. This paper puts forward a model of Workflow-oriented Attributed Based Access Control (WABAC, and design an access control framework based on WABAC model. The model grants permissions to subjects according to subject atttribute, resource attribute, environment attribute and current task, meeting access control request of SOC. Using the approach presented can effectively enhance the access control security for SOC applications, and prevent the abuse of subject permissions.

  1. Path Control Experiment of Mobile Robot Based on Supervised Learning

    Directory of Open Access Journals (Sweden)

    Gao Chi

    2013-07-01

    Full Text Available To solve the weak capacity and low control accuracy of the robots which adapt to the complex working conditions, proposed that a path control method based on the driving experience and supervised learning. According to the slope road geometry characteristics, established the modeling study due to ramp pavement path control method and the control structure based on monitoring and self-learning. Made use of the Global Navigation Satellite System did the experiment. The test data illustrates that when the running speed is not greater than 5 m / s, the straight-line trajectory path transverse vertical deviation within 士20cm ,which proved that the control method has a high feasibility. 

  2. Adaptive robust controller based on integral sliding mode concept

    Science.gov (United States)

    Taleb, M.; Plestan, F.

    2016-09-01

    This paper proposes, for a class of uncertain nonlinear systems, an adaptive controller based on adaptive second-order sliding mode control and integral sliding mode control concepts. The adaptation strategy solves the problem of gain tuning and has the advantage of chattering reduction. Moreover, limited information about perturbation and uncertainties has to be known. The control is composed of two parts: an adaptive one whose objective is to reject the perturbation and system uncertainties, whereas the second one is chosen such as the nominal part of the system is stabilised in zero. To illustrate the effectiveness of the proposed approach, an application on an academic example is shown with simulation results.

  3. Electric Vehicle IM Controller Based on Voltage-Fed Inverter

    Institute of Scientific and Technical Information of China (English)

    宋建国; 张承宁; 袁学; 谭建

    2004-01-01

    A novel electric vehicle (EV) induction motor (IM) controller based on voltage-fed inverter is presented. It is shown that the proposed adaptive control algorithm effectively both simplifies the structure and expands the capacity of controller. The relationship between stator's voltage and that of current under rotor's flux-oriented-coordinates is first introduced, and then the structure of vector control is analyzed, in which voltage compensation is inducted as the core feedback procedure. Experiments prove that, together with a facility for realization, a smooth transition, a prompt torque response and small concussion are gained. Extensive research conducted by varying parameters that result in practical ripple is proposed in conclusion.

  4. Expectation-Based Control of Noise and Chaos

    Science.gov (United States)

    Zak, Michael

    2006-01-01

    A proposed approach to control of noise and chaos in dynamic systems would supplement conventional methods. The approach is based on fictitious forces composed of expectations governed by Fokker-Planck or Liouville equations that describe the evolution of the probability densities of the controlled parameters. These forces would be utilized as feedback control forces that would suppress the undesired diffusion of the controlled parameters. Examples of dynamic systems in which the approach is expected to prove beneficial include spacecraft, electronic systems, and coupled lasers.

  5. Nonlinear system identification and control based on modular neural networks.

    Science.gov (United States)

    Puscasu, Gheorghe; Codres, Bogdan

    2011-08-01

    A new approach for nonlinear system identification and control based on modular neural networks (MNN) is proposed in this paper. The computational complexity of neural identification can be greatly reduced if the whole system is decomposed into several subsystems. This is obtained using a partitioning algorithm. Each local nonlinear model is associated with a nonlinear controller. These are also implemented by neural networks. The switching between the neural controllers is done by a dynamical switcher, also implemented by neural networks, that tracks the different operating points. The proposed multiple modelling and control strategy has been successfully tested on simulated laboratory scale liquid-level system.

  6. Engine control system having fuel-based timing

    Science.gov (United States)

    Willi, Martin L [Dunlap, IL; Fiveland, Scott B [Metamora, IL; Montgomery, David T [Edelstein, IL; Gong, Weidong [Dunlap, IL

    2012-04-03

    A control system for an engine having a cylinder is disclosed having an engine valve movable to regulate a fluid flow of the cylinder and an actuator associated with the engine valve. The control system also has a sensor configured to generate a signal indicative of an amount of an air/fuel mixture remaining within the cylinder after completion of a first combustion event and a controller in communication with the actuator and the sensor. The controller may be configured to compare the amount with a desired amount, and to selectively regulate the actuator to adjust a timing of the engine valve associated with a subsequent combustion event based on the comparison.

  7. Rate control algorithm based on frame complexity estimation for MVC

    Science.gov (United States)

    Yan, Tao; An, Ping; Shen, Liquan; Zhang, Zhaoyang

    2010-07-01

    Rate control has not been well studied for multi-view video coding (MVC). In this paper, we propose an efficient rate control algorithm for MVC by improving the quadratic rate-distortion (R-D) model, which reasonably allocate bit-rate among views based on correlation analysis. The proposed algorithm consists of four levels for rate bits control more accurately, of which the frame layer allocates bits according to frame complexity and temporal activity. Extensive experiments show that the proposed algorithm can efficiently implement bit allocation and rate control according to coding parameters.

  8. Multi-telerobot collaboration based on coordinated controller

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    A coordinated controller used for multi-telerobots collaboration was presented based on the strategy of shared control. First, it can overcome the effect of time delay. And, it combines the intelligence of the master side and the slave side, which cannot only increase the efficiency and the safety of the system but also relieve the burden and requirements of the operator. The controller can also cope with the collision between two telerobots. A simulation experiment was carried out to verify the validity of the controller for two slave robots.

  9. Lyapunov function-based control laws for revolute robot arms - Tracking control, robustness, and adaptive control

    Science.gov (United States)

    Wen, John T.; Kreutz-Delgado, Kenneth; Bayard, David S.

    1992-01-01

    A new class of joint level control laws for all-revolute robot arms is introduced. The analysis is similar to a recently proposed energy-like Liapunov function approach, except that the closed-loop potential function is shaped in accordance with the underlying joint space topology. This approach gives way to a much simpler analysis and leads to a new class of control designs which guarantee both global asymptotic stability and local exponential stability. When Coulomb and viscous friction and parameter uncertainty are present as model perturbations, a sliding mode-like modification of the control law results in a robustness-enhancing outer loop. Adaptive control is formulated within the same framework. A linear-in-the-parameters formulation is adopted and globally asymptotically stable adaptive control laws are derived by simply replacing unknown model parameters by their estimates (i.e., certainty equivalence adaptation).

  10. Lyapunov function-based control laws for revolute robot arms - Tracking control, robustness, and adaptive control

    Science.gov (United States)

    Wen, John T.; Kreutz-Delgado, Kenneth; Bayard, David S.

    1992-01-01

    A new class of joint level control laws for all-revolute robot arms is introduced. The analysis is similar to a recently proposed energy-like Liapunov function approach, except that the closed-loop potential function is shaped in accordance with the underlying joint space topology. This approach gives way to a much simpler analysis and leads to a new class of control designs which guarantee both global asymptotic stability and local exponential stability. When Coulomb and viscous friction and parameter uncertainty are present as model perturbations, a sliding mode-like modification of the control law results in a robustness-enhancing outer loop. Adaptive control is formulated within the same framework. A linear-in-the-parameters formulation is adopted and globally asymptotically stable adaptive control laws are derived by simply replacing unknown model parameters by their estimates (i.e., certainty equivalence adaptation).

  11. Adaptive control with an expert system based supervisory level. Thesis

    Science.gov (United States)

    Sullivan, Gerald A.

    1991-01-01

    Adaptive control is presently one of the methods available which may be used to control plants with poorly modelled dynamics or time varying dynamics. Although many variations of adaptive controllers exist, a common characteristic of all adaptive control schemes, is that input/output measurements from the plant are used to adjust a control law in an on-line fashion. Ideally the adjustment mechanism of the adaptive controller is able to learn enough about the dynamics of the plant from input/output measurements to effectively control the plant. In practice, problems such as measurement noise, controller saturation, and incorrect model order, to name a few, may prevent proper adjustment of the controller and poor performance or instability result. In this work we set out to avoid the inadequacies of procedurally implemented safety nets, by introducing a two level control scheme in which an expert system based 'supervisor' at the upper level provides all the safety net functions for an adaptive controller at the lower level. The expert system is based on a shell called IPEX, (Interactive Process EXpert), that we developed specifically for the diagnosis and treatment of dynamic systems. Some of the more important functions that the IPEX system provides are: (1) temporal reasoning; (2) planning of diagnostic activities; and (3) interactive diagnosis. Also, because knowledge and control logic are separate, the incorporation of new diagnostic and treatment knowledge is relatively simple. We note that the flexibility available in the system to express diagnostic and treatment knowledge, allows much greater functionality than could ever be reasonably expected from procedural implementations of safety nets. The remainder of this chapter is divided into three sections. In section 1.1 we give a detailed review of the literature in the area of supervisory systems for adaptive controllers. In particular, we describe the evolution of safety nets from simple ad hoc techniques, up

  12. Autonomous Control Reconfiguration of Aerospace Vehicle Based on Control Effectiveness Estimation

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Future aerospace vehicles (ASV) are designed to fly in both inner and extra atrmospheric fields, which requires autonomous adaptability to the uncertainties emanated from abrupt faults and continuously time-varying environments. An autonomous control reconfiguration scheme is presented for ASV to deal with the uncertainties on the base of control effectiveness estimation. The on-line estimation methods for the time-varying control effectiveness of linear control system are investigated. Some sufficient conditions for the estimable system are given for different cases. There are proposed corresponding on-line estimation algorithms which are proved to be convergent and robust to noise using the least-square-based methods. On the ground of fuzzy logic and linear programming, the control allocation algorithms, which are able to implement the autonomous control reconfiguration through the redundant actuators, are put forward. Finally, an integrated system is developed to verify the scheme and algorithms by way of numerical simulation and analysis.

  13. Backstepping design of missile guidance and control based on adaptive fuzzy sliding mode control

    Institute of Scientific and Technical Information of China (English)

    Ran Maopeng; Wang Qing; Hou Delong; Dong Chaoyang

    2014-01-01

    This paper presents an integrated missile guidance and control law based on adaptive fuzzy sliding mode control. The integrated model is formulated as a block-strict-feedback nonlinear system, in which modeling errors, unmodeled nonlinearities, target maneuvers, etc. are viewed as unknown uncertainties. The adaptive nonlinear control law is designed based on backstepping and sliding mode control techniques. An adaptive fuzzy system is adopted to approximate the coupling nonlinear functions of the system, and for the uncertainties, we utilize an online-adaptive control law to estimate the unknown parameters. The stability analysis of the closed-loop system is also conducted. Simulation results show that, with the application of the adaptive fuzzy sliding mode control, small miss distances and smooth missile trajectories are achieved, and the system is robust against system uncertainties and external disturbances.

  14. Chaos Control in Memristor-based Oscillators Using Intelligent Sliding Mode Control

    Directory of Open Access Journals (Sweden)

    Amir Hossein Abolmasoumi

    2014-10-01

    Full Text Available In this paper, Intelligent Sliding Mode Control of chaos in a memristor- based Chua’s oscillator is investigated. In order to gain stabilization and tracking of a sinusoidal input, an appropriate sliding surface is proposed and sliding gain is tuned. Also, to avoid the chattering phenomenon in traditional sliding mode controller, and to reduce the hitting time of the controlled system, an especial genetic algorithm optimization method is suggested. By defining a new objective function and searching for optimal the controller parameters the convergence time and chattering are reduced considerably. The usefulness of the proposed controller with intelligent tuning method for chaos control of memristorbased oscillators is demonstrated in memristor- based Chua's circuit.

  15. Sensorless speed control of switched reluctance motor using brain emotional learning based intelligent controller

    Energy Technology Data Exchange (ETDEWEB)

    Dehkordi, Behzad Mirzaeian, E-mail: mirzaeian@eng.ui.ac.i [Department of Electrical Engineering, Faculty of Engineering, University of Isfahan, Hezar-Jerib St., Postal code 8174673441, Isfahan (Iran, Islamic Republic of); Parsapoor, Amir, E-mail: amirparsapoor@yahoo.co [Department of Electrical Engineering, Faculty of Engineering, University of Isfahan, Hezar-Jerib St., Postal code 8174673441, Isfahan (Iran, Islamic Republic of); Moallem, Mehdi, E-mail: moallem@cc.iut.ac.i [Department of Electrical Engineering, Isfahan University of Technology, Isfahan (Iran, Islamic Republic of); Lucas, Caro, E-mail: lucas@ut.ac.i [Centre of Excellence for Control and Intelligent Processing, Electrical and Computer Engineering Faculty, College of Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

    2011-01-15

    In this paper, a brain emotional learning based intelligent controller (BELBIC) is developed to control the switched reluctance motor (SRM) speed. Like other intelligent controllers, BELBIC is model free and is suitable to control nonlinear systems. Motor parameter changes, operating point changes, measurement noise, open circuit fault in one phase and asymmetric phases in SRM are also simulated to show the robustness and superior performance of BELBIC. To compare the BELBIC performance with other intelligent controllers, Fuzzy Logic Controller (FLC) is developed. System responses with BELBIC and FLC are compared. Furthermore, by eliminating the position sensor, a method is introduced to estimate the rotor position. This method is based on Adaptive Neuro Fuzzy Inference System (ANFIS). The estimator inputs are four phase flux linkages. Suggested rotor position estimator is simulated in different conditions. Simulation results confirm the accurate rotor position estimation in different loads and speeds.

  16. FBFN-based adaptive repetitive control of nonlinearly parameterized systems

    Institute of Scientific and Technical Information of China (English)

    Wenli Sun; Hong Cai; Fu Zhao

    2013-01-01

    An adaptive repetitive control scheme is presented for a class of nonlinearly parameterized systems based on the fuzzy ba-sis function network (FBFN). The parameters of the fuzzy rules are tuned with adaptive schemes. To attenuate chattering effectively, the discontinuous control term is approximated by an adaptive PI control structure. The bound of the discontinuous control term is assumed to be unknown and estimated by an adaptive mecha-nism. Based on the Lyapunov stability theory, an adaptive repeti-tive control law is proposed to guarantee the closed-loop stability and the tracking performance. By means of FBFNs, which avoid the nonlinear parameterization from entering into the adaptive repetitive control, the control er singularity problem is solved. The proposed approach does not require an exact structure of the sys-tem dynamics, and the proposed control er is utilized to control a model of permanent-magnet linear synchronous motor subject to significant disturbances and parameter uncertainties. The simula-tion results demonstrate the effectiveness of the proposed method.

  17. ITER fast plant system controller prototype based on ATCA platform

    Energy Technology Data Exchange (ETDEWEB)

    Goncalves, B., E-mail: bruno@ipfn.ist.utl.pt [Instituto de Plasmas e Fusao Nuclear - Laboratorio Associado, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, P-1049-001 Lisboa (Portugal); Sousa, J.; Carvalho, B.B.; Batista, A.; Neto, A.; Santos, B.; Duarte, A.; Valcarcel, D.; Alves, D.; Correia, M.; Rodrigues, A.P.; Carvalho, P.F. [Instituto de Plasmas e Fusao Nuclear - Laboratorio Associado, Instituto Superior Tecnico, Universidade Tecnica de Lisboa, P-1049-001 Lisboa (Portugal); Ruiz, M. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (Spain); Vega, J.; Castro, R. [Centro de Investigaciones Energeticas, Medioambientales y Tecnologicas, CIEMAT, Av. Complutense, Madrid (Spain); Lopez, J.M. [Grupo de Investigacion en Instrumentacion y Acustica Aplicada, Universidad Politecnica de Madrid (Spain); Utzel, N.; Makijarvi, P. [ITER Organization, CS 90 046, 13067 St. Paul lez Durance Cedex (France)

    2012-12-15

    The ITER fast plan system controllers (FPSC) are based on embedded technologies. The FPSCs [1] will be devoted to data acquisition tasks (sampling rates >1 kSPS) and control purposes in closed-control loops whose cycle times are below 1 ms. Fast controllers will be dedicated industrial controllers with the ability to supervise other fast and/or slow controllers and interface to actuators, sensors and high performance networks. This contribution presents an FPSC prototype, specialized for data acquisition, based on the ATCA (Advanced Telecommunications Computing Architecture) standard. This prototyping activity contributes to the ITER Plant Control Design Handbook (PCDH) effort of standardization, specifically regarding fast controller characteristics. For the prototype, IPFN has developed a new family of ATCA modules targeting ITER requirements. This family of modules comprises an AMC (Advanced Mezzanine Card) carrier/data hub/timing hub, compliant with the upcoming ATCA extensions for Physics, and a multi-channel galvanically isolated PnP digitizer, designed for serviceability. The design and test of a peer-to-peer communications layer for the implementation of a reflective memory over PCI Express and the design and test of an IEEE-1588 transport layer over an high performance serial link were also performed. In this contribution, a complete description of the solution is presented as well as the integration of the controller into the standard CODAC environment. The most relevant test results will be addressed, focusing in the benefits and limitations of the applied technologies.

  18. Adaptive control for solar energy based DC microgrid system development

    Science.gov (United States)

    Zhang, Qinhao

    During the upgrading of current electric power grid, it is expected to develop smarter, more robust and more reliable power systems integrated with distributed generations. To realize these objectives, traditional control techniques are no longer effective in either stabilizing systems or delivering optimal and robust performances. Therefore, development of advanced control methods has received increasing attention in power engineering. This work addresses two specific problems in the control of solar panel based microgrid systems. First, a new control scheme is proposed for the microgrid systems to achieve optimal energy conversion ratio in the solar panels. The control system can optimize the efficiency of the maximum power point tracking (MPPT) algorithm by implementing two layers of adaptive control. Such a hierarchical control architecture has greatly improved the system performance, which is validated through both mathematical analysis and computer simulation. Second, in the development of the microgrid transmission system, the issues related to the tele-communication delay and constant power load (CPL)'s negative incremental impedance are investigated. A reference model based method is proposed for pole and zero placements that address the challenges of the time delay and CPL in closed-loop control. The effectiveness of the proposed modeling and control design methods are demonstrated in a simulation testbed. Practical aspects of the proposed methods for general microgrid systems are also discussed.

  19. Model based control for run-of-river system. Part 2: Comparison of control structures

    Directory of Open Access Journals (Sweden)

    Liubomyr Vytvytskyi

    2015-10-01

    Full Text Available Optimal operation and control of a run-of-river hydro power plant depend on good knowledge of the elements of the plant in the form of models. Both the control architecture of the system, i.e. the choice of inputs and outputs, and to what degree a model is used, will affect the achievable control performance. Here, a model of a river reach based on the Saint Venant equations for open channel flow illustrates the dynamics of the run-of-river system. The hyperbolic partial differential equations are discretized using the Kurganov-Petrova central upwind scheme - see Part I for details. A comparison is given of achievable control performance using two alternative control signals: the inlet or the outlet volumetric flow rates to the system, in combination with a number of different control structures such as PI control, PI control with Smith predictor, and predictive control. The control objective is to keep the level just in front of the dam as high as possible, and with little variation in the level to avoid overflow over the dam. With a step change in the volumetric inflow to the river reach (disturbance and using the volumetric outflow as the control signal, PI control gives quite good performance. Model predictive control (MPC gives superior control in the sense of constraining the variation in the water level, at a cost of longer computational time and thus constraints on possible sample time. Details on controller tuning are given. With volumetric inflow to the river reach as control signal and outflow (production as disturbance, this introduces a considerable time delay in the control signal. Because of nonlinearity in the system (varying time delay, etc., it is difficult to achieve stable closed loop performance using a simple PI controller. However, by combining a PI controller with a Smith predictor based on a simple integrator + fixed time delay model, stable closed loop operation is possible with decent control performance. Still, an MPC

  20. Leg compliance control of a hexapod robot based on improved adaptive control in different environments

    Institute of Scientific and Technical Information of China (English)

    朱雅光; 金波; 李伟

    2015-01-01

    Considering the compliance control problem of a hexapod robot under different environments, a control strategy based on the improved adaptive control algorithm is proposed. The model of robot structure and impedance control is established. Then, the indirect adaptive control algorithm is derived. Through the analysis of its parameters, it can be noticed that the algorithm does not meet the requirements of the robot compliance control in a complex environment. Therefore, the fuzzy control algorithm is used to adjust the adaptive control parameters. The satisfied system response can be obtained based on the adjustment in real time according to the error between input and output. Comparative experiments and analysis of traditional adaptive control and the improved adaptive control algorithm are presented. It can be verified that not only desired contact force can be reached quickly in different environments, but also smaller contact impact and sliding avoidance are guaranteed, which means that the control strategy has great significance to enhance the adaptability of the hexapod robot.

  1. Robustness and Actuator Bandwidth of MRP-Based Sliding Mode Control for Spacecraft Attitude Control Problems

    Science.gov (United States)

    Keum, Jung-Hoon; Ra, Sung-Woong

    2009-12-01

    Nonlinear sliding surface design in variable structure systems for spacecraft attitude control problems is studied. A robustness analysis is performed for regular form of system, and calculation of actuator bandwidth is presented by reviewing sliding surface dynamics. To achieve non-singular attitude description and minimal parameterization, spacecraft attitude control problems are considered based on modified Rodrigues parameters (MRP). It is shown that the derived controller ensures the sliding motion in pre-determined region irrespective of unmodeled effects and disturbances.

  2. Chaos Control in Memristor-based Oscillators Using Intelligent Sliding Mode Control

    OpenAIRE

    Amir Hossein Abolmasoumi; Somayeh Khosravinejad

    2014-01-01

    In this paper, Intelligent Sliding Mode Control of chaos in a memristor- based Chua’s oscillator is investigated. In order to gain stabilization and tracking of a sinusoidal input, an appropriate sliding surface is proposed and sliding gain is tuned. Also, to avoid the chattering phenomenon in traditional sliding mode controller, and to reduce the hitting time of the controlled system, an especial genetic algorithm optimization method is suggested. By defining a new objective func...

  3. Control system of the MACSE project; Le systeme de controle du projet MACSE

    Energy Technology Data Exchange (ETDEWEB)

    Gournay, J.F.; Gougnaud, F.; Matichard, G.; Azoulay, R.; Bouillac, A.

    1991-12-31

    With the goal of investigating all the technological aspects of superconducting RF acceleration, the so-called MACSE facility was put in operation at the end of 1990. The control system is built with several VME crates linked together with a dedicated Ethernet network. VxWorks is the real-time operating system used. A set of software services was built on top of VxWorks (high level communication tools, a data-base management system, a library of VME boards drivers and a limited man-machine interface). A complete range of application programs have been developed with these tools in order to fulfill the requirements of such a facility (settings of the parameters, surveillance, archive facility, closed loops...). The TCP-IP protocols family is extensively used for communications between the components of the system (UDP, RPC, rcmd, NFS). The development environment is based on the host-target approach through the use of a network of Sun 3/80 workstations. After 1 1/2 year of experience, this system has proven to be powerful and flexible.

  4. GENETIC BASED PLUS INTEGRAL CONTROLLER FOR PMBLDC MOTOR CONTROL USING RESONANT POLE INVERTER

    Directory of Open Access Journals (Sweden)

    Muruganantham

    2012-01-01

    Full Text Available Permanent Magnet Brushless DC (PMBLDC motor drives are increasingly popular in industrial applications due to rapid progress of technologies in power electronics and the growing demand for energy saving. The increasing demand of energy saving from society is the external force for the development of PMBLDC motor drives. It is however driven by a hard-switching Pulse Width Modulation (PWM inverter, which has low switching frequency, high switching loss, high Electro-Magnetic Interference (EMI, high acoustic noise and low efficiency, etc. To solve these problems of the hard-switching inverter, many soft-switching inverters have been designed in the past. Unfortunately, high device voltage stress, large dc link voltage ripples, complex control scheme and so on are noticed in the soft-switching inverters. This study introduces a novel genetic-proportional Plus Integral (PI controller based resonant pole inverter using transformer, which can generate dc link voltage notches during chopping which minimize the drawbacks of soft-switching. Hence all switches work in zero-voltage switching condition. The performance of the genetic-based PI controller is compared with conventional PI controller. The experimental results show that the genetic-based PI controller renders a better transient response than the conventional PI controller resulting in negligible overshoot, smaller settling time and rise time. Moreover the proposed controller provides low torque ripples and high starting torque. Both simulation and experimental results are presented to show the superiority of the proposed GA-PI controller based resonant pole inverter.

  5. Predictive current control of permanent magnet synchronous motor based on linear active disturbance rejection control

    Science.gov (United States)

    Li, Kunpeng

    2017-01-01

    The compatibility problem between rapidity and overshooting in the traditional predictive current control structure is inevitable and difficult to solve by reason of using PI controller. A novel predictive current control (PCC) algorithm for permanent magnet synchronous motor (PMSM) based on linear active disturbance rejection control (LADRC) is presented in this paper. In order to displace PI controller, the LADRC strategy which consisted of linear state error feedback (LSEF) control algorithm and linear extended state observer (LESO), is designed based on the mathematic model of PMSM. The purpose of LSEF is to make sure fast response to load mutation and system uncertainties, and LESO is designed to estimate the uncertain disturbances. The principal structures of the proposed system are speed outer loop based on LADRC and current inner loop based on predictive current control. Especially, the instruction value of qaxis current in inner loop is derived from the control quantity which is designed in speed outer loop. The simulation is carried out in Matlab/Simulink software, and the results illustrate that the dynamic and static performances of proposed system are satisfied. Moreover the robust against model parameters mismatch is enhanced obviously.

  6. Low-Cost Undergraduate Control Systems Experiments Using Microcontroller-Based Control of a DC Motor

    Science.gov (United States)

    Gunasekaran, M.; Potluri, R.

    2012-01-01

    This paper presents low-cost experiments for a control systems laboratory module that is worth one and a third credits. The experiments are organized around the microcontroller-based control of a permanent magnet dc motor. The experimental setups were built in-house. Except for the operating system, the software used is primarily freeware or free…

  7. Interconnection and damping assignment passivity-based control of port-controlled Hamiltonian systems

    NARCIS (Netherlands)

    Ortega, Romeo; Schaft, Arjan van der; Maschke, Bernhard; Escobar, Gerardo

    2002-01-01

    Passivity-based control (PBC) is a well-established technique that has shown to be very powerful to design robust controllers for physical systems described by Euler–Lagrange (EL) equations of motion. For regulation problems of mechanical systems, which can be stabilized “shaping” only the potential

  8. Matching in the method of controlled Lagrangians and IDA-passivity based control

    NARCIS (Netherlands)

    Blankenstein, Guido; Ortega, Romeo; Schaft, van der Arjan J.; Astolfi, A.

    2006-01-01

    This paper reviews the method of controlled Lagrangians and the interconnection and damping assignment passivity based control (IDA-PBC)method. Both methods have been presented recently in the literature as means to stabilize a desired equilibrium point of an Euler-Lagrange system, respectively Hami

  9. Low-Cost Undergraduate Control Systems Experiments Using Microcontroller-Based Control of a DC Motor

    Science.gov (United States)

    Gunasekaran, M.; Potluri, R.

    2012-01-01

    This paper presents low-cost experiments for a control systems laboratory module that is worth one and a third credits. The experiments are organized around the microcontroller-based control of a permanent magnet dc motor. The experimental setups were built in-house. Except for the operating system, the software used is primarily freeware or free…

  10. Formation control of multiple Euler-Lagrange systems via null-space-based behavioral control

    NARCIS (Netherlands)

    Chen, Jie; Huang, Jie; Dou, Lihua; Fang, Hao

    2016-01-01

    This paper addresses the formation control problem of multiple Euler-Lagrange systems with model uncertainties in the environment containing obstacles. Utilizing the null-space-based (NSB) behavioral control architecture, the proposed problem can be decomposed into elementary missions (behaviors) wi

  11. Adaptive Control for Robotic Manipulators Base on RBF Neural Network

    Directory of Open Access Journals (Sweden)

    MA Jing

    2013-09-01

    Full Text Available An adaptive neural network controller is brought forward by the paper to solve trajectory tracking problems of robotic manipulators with uncertainties. The first scheme consists of a PD feedback and a dynamic compensator which is composed by neural network controller and variable structure controller. Neutral network controller is designed to adaptive learn and compensate the unknown uncertainties, variable structure controller is designed to eliminate approach errors of neutral network. The adaptive weight learning algorithm of neural network is designed to ensure online real-time adjustment, offline learning phase is not need; Global asymptotic stability (GAS of system base on Lyapunov theory is analysised to ensure the convergence of the algorithm. The simulation result s show that the kind of the control scheme is effective and has good robustness.

  12. DYNAMICS BASED CONTROL OF A SKID STEERING MOBILE ROBOT

    Directory of Open Access Journals (Sweden)

    Osama Elshazly

    2016-06-01

    Full Text Available In this paper, development of a reduced order, augmented dynamics-drive model that combines both the dynamics and drive subsystems of the skid steering mobile robot (SSMR is presented. A Linear Quadratic Regulator (LQR control algorithm with feed-forward compensation of the disturbances part included in the reduced order augmented dynamics-drive model is designed. The proposed controller has many advantages such as its simplicity in terms of design and implementation in comparison with complex nonlinear control schemes that are usually designed for this system. Moreover, the good performance is also provided by the controller for the SSMR comparable with a nonlinear controller based on the inverse dynamics which depends on the availability of an accurate model describing the system. Simulation results illustrate the effectiveness and enhancement provided by the proposed controller.

  13. Temperature prediction control based on least squares support vector machines

    Institute of Scientific and Technical Information of China (English)

    Bin LIU; Hongye SU; Weihua HUANG; Jian CHU

    2004-01-01

    A prediction control algorithm is presented based on least squares support vector machines (LS-SVM) model for a class of complex systems with strong nonlinearity.The nonlinear off-line model of the controlled plant is built by LS-SVM with radial basis function (RBF) kernel.In the process of system running,the off-line model is linearized at each sampling instant,and the generalized prediction control (GPC) algorithm is employed to implement the prediction control for the controlled plant.The obtained algorithm is applied to a boiler temperature control system with complicated nonlinearity and large time delay.The results of the experiment verify the effectiveness and merit of the algorithm.

  14. Agent-based distributed hierarchical control of dc microgrid systems

    DEFF Research Database (Denmark)

    Meng, Lexuan; Vasquez, Juan Carlos; Guerrero, Josep M.

    2014-01-01

    In order to enable distributed control and management for microgrids, this paper explores the application of information consensus and local decisionmaking methods formulating an agent based distributed hierarchical control system. A droop controlled paralleled DC/DC converter system is taken...... as a case study. The objective is to enhance the system efficiency by finding the optimal sharing ratio of load current. Virtual resistances in local control systems are taken as decision variables. Consensus algorithms are applied for global information discovery and local control systems coordination....... Standard genetic algorithm is applied in each local control system in order to search for a global optimum. Hardware-in-Loop simulation results are shown to demonstrate the effectiveness of the method....

  15. Embedded Control System Design A Model Based Approach

    CERN Document Server

    Forrai, Alexandru

    2013-01-01

    Control system design is a challenging task for practicing engineers. It requires knowledge of different engineering fields, a good understanding of technical specifications and good communication skills. The current book introduces the reader into practical control system design, bridging  the gap between theory and practice.  The control design techniques presented in the book are all model based., considering the needs and possibilities of practicing engineers. Classical control design techniques are reviewed and methods are presented how to verify the robustness of the design. It is how the designed control algorithm can be implemented in real-time and tested, fulfilling different safety requirements. Good design practices and the systematic software development process are emphasized in the book according to the generic standard IEC61508. The book is mainly addressed to practicing control and embedded software engineers - working in research and development – as well as graduate students who are face...

  16. Vehicle Chassis Integrated Control Based on Multimodel and Multilevel Hierarchical Control

    Directory of Open Access Journals (Sweden)

    Shu-en Zhao

    2014-01-01

    Full Text Available Aiming at the differences of vehicle chassis key subsystems influence on vehicle handling stability and effective acting regions, comprehensive considering of the nonlinear characteristic of the tires and the dynamic coupling among suspension, steering, and braking subsystems in vehicle chassis, the 14-DOF full vehicle model is built. Based on the control characteristic local optimum of each subsystem, multilevel hierarchical control theory is adopted and the vehicle stability coordinated control system including organization, coordination, and execution level is established. Using sliding mode control theory and the inverse tire model, the generalized target forces and moments from organization level are translated into the tire sideslip angle and slip ratio. And then, based on the principle of functional allocation, the control functions of each subsystem are coordinated and the function decoupling of vehicle chassis complex system is realized. The Matlab/Simulink platform is used and the full vehicle stability coordinated control system is simulated. The results show that the full vehicle coordinated control system based on multilevel hierarchical control theory can improve the vehicle stability preferably than the subsystem combined control and uncontrolled system.

  17. Dynamically Authorized Role-Based Access Control for Grid Applications

    Institute of Scientific and Technical Information of China (English)

    YAO Hanbing; HU Heping; LU Zhengding; LI Ruixuan

    2006-01-01

    Grid computing is concerned with the sharing and coordinated use of diverse resources in distributed "virtual organizations". The heterogeneous, dynamic and multi-domain nature of these environments makes challenging security issues that demand new technical approaches. Despite the recent advances in access control approaches applicable to Grid computing, there remain issues that impede the development of effective access control models for Grid applications. Among them there are the lack of context-based models for access control, and reliance on identity or capability-based access control schemes. An access control scheme that resolve these issues is presented, and a dynamically authorized role-based access control (D-RBAC) model extending the RBAC with context constraints is proposed. The D-RABC mechanisms dynamically grant permissions to users based on a set of contextual information collected from the system and user's environments, while retaining the advantages of RBAC model. The implementation architecture of D-RBAC for the Grid application is also described.

  18. Vision-based control in driving assistance of agricultural vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Khadraoui, D.; Martinet, P.; Bonton, P.; Gallice, J. [Univ. Blaise Pascal, Aubiere (France). Lab. des Sciences et Materiaux pour l`Electronique et d`Automatique; Debain, C. [Inst. de Recherche pour l`Ingenierie de l`Agriculture et de l`Environment, Montoldre (France). Div. Techniques du Machinisme Agricole; Rouveure, R. [Inst. de Recherche pour l`Ingenierie de l`Agriculture et de l`Environment, Antony (France). Div. Electronique et Intelligence Artificielle

    1998-10-01

    This article presents a real-time control system for an agricultural mobile machine (vehicle) based on an on-board vision system using a single camera. This system has been designed to help humans in repetitive and difficult tasks in the agricultural domain. The aim of the robotics application concerns the control of the vehicle with regard to the reap limit detected in image space. The perception aspect in relation to the application has been described in previous work, and here the authors deal with the control aspect. They integrate image features issues from the modeling of the scene in the control loop to perform an image-based servoing technique. The vehicle behavior described here concerns bicycle and neural models, and three control laws are then synthesized. The first and the second are modeling approaches and use an interaction between the scene and the image space. They are based on the regulation of a task function. The third is a black-box modeling technique, and is based on a neural network. Finally, experimental results obtained with these different control laws in different conditions are presented and discussed.

  19. An LMI-based decoupling control for electromagnetic formation flight

    Directory of Open Access Journals (Sweden)

    Huang Xianlin

    2015-04-01

    Full Text Available Electromagnetic formation flight (EMFF leverages electromagnetic force to control the relative position of satellites. EMFF offers a promising alternative to traditional propellant-based spacecraft flight formation. This novel strategy is very attractive since it does not consume fuel. Due to the highly coupled nonlinearity of electromagnetic force, it is difficult to individually design a controller for one satellite without considering others, which poses challenges to communications. This paper is devoted to decoupling control of EMFF, including regulations, constraints and controller design. A learning-based adaptive sliding mode decoupling controller is analyzed to illustrate the problem of existing results, and input rate saturation is introduced to guarantee the validity of frequency division technique. Through transformation, the imposed input rate saturation is converted to state and input constraints. A linear matrix inequalities (LMI-based robust optimal control method can then be used and improved to solve the transformed problem. Simulation results are presented to demonstrate the effectiveness of the proposed decoupling control.

  20. PLC BASED RATIO CONTROLLER AND MATERIAL DISTRIBUTION SYSTEM

    Directory of Open Access Journals (Sweden)

    V. M. Badwaik Prof. V. M. Umale

    2012-04-01

    Full Text Available Automation in an industry using programmable logic controller (PLC can be enumerated by optimizing the use of process control equipment, decreases the response time for process and equipment contingencies, provides information about process status, manages process logic at the plant floor level and increases overall productivity and plant efficiency. The primary reason for designing such a system is to eliminate large cost involved in replacing complicated relay based machine control system & to reduce process time. Ratio control system is feed forward system where one variable is controlled in ratio to another to satisfy some higher level objectives. Two difference chemicals are supplied from different tanks in proper ratio by maintaining the flow of quantity. Then desired mixture is obtained &checks the ratio of composition if any unbalanced, controlled by controlled values of supply tanks. Then this mixture is distributed as per requirements. In Industries for ten machines, total cycle time with existing PLC based system is 75 sec. But our modified PLC based system total cycle time is improved as 45 sec. Hence total reach time of distribution system is improved.

  1. Implementing context and team based access control in healthcare intranets.

    Science.gov (United States)

    Georgiadis, Christos K; Mavridis, Ioannis K; Nikolakopoulou, Georgia; Pangalos, George I

    2002-09-01

    The establishment of an efficient access control system in healthcare intranets is a critical security issue directly related to the protection of patients' privacy. Our C-TMAC (Context and Team-based Access Control) model is an active security access control model that layers dynamic access control concepts on top of RBAC (Role-based) and TMAC (Team-based) access control models. It also extends them in the sense that contextual information concerning collaborative activities is associated with teams of users and user permissions are dynamically filtered during runtime. These features of C-TMAC meet the specific security requirements of healthcare applications. In this paper, an experimental implementation of the C-TMAC model is described. More specifically, we present the operational architecture of the system that is used to implement C-TMAC security components in a healthcare intranet. Based on the technological platform of an Oracle Data Base Management System and Application Server, the application logic is coded with stored PL/SQL procedures that include Dynamic SQL routines for runtime value binding purposes. The resulting active security system adapts to current need-to-know requirements of users during runtime and provides fine-grained permission granularity. Apart from identity certificates for authentication, it uses attribute certificates for communicating critical security metadata, such as role membership and team participation of users.

  2. Combined Active and Reactive Power Control of Wind Farms based on Model Predictive Control

    DEFF Research Database (Denmark)

    Zhao, Haoran; Wu, Qiuwei; Wang, Jianhui;

    2017-01-01

    This paper proposes a combined wind farm controller based on Model Predictive Control (MPC). Compared with the conventional decoupled active and reactive power control, the proposed control scheme considers the significant impact of active power on voltage variations due to the low X=R ratio...... of wind farm collector systems. The voltage control is improved. Besides, by coordination of active and reactive power, the Var capacity is optimized to prevent potential failures due to Var shortage, especially when the wind farm operates close to its full load. An analytical method is used to calculate...... the sensitivity coefficients to improve the computation efficiency and overcome the convergence problem. Two control modes are designed for both normal and emergency conditions. A wind farm with 20 wind turbines was used to verify the proposed combined control scheme....

  3. Permanent magnet brushless motor control based on ADRC

    Directory of Open Access Journals (Sweden)

    Li Xiaokun

    2016-01-01

    Full Text Available Permanent magnet brushless motor is a nonlinear system with multiple variables, the mathematical model of Permanent magnet brushless motor is difficult to establish, and since that the classic PID control is hard to precisely control the motor. Active disturbance rejection control (ADRC technique is a new nonlinear controller which does not depend on the system model. It is starting from the classic PID control, and establishing the loop control system by error negative feedback, the ESO(extended state observer observing system which comes from the observer theory of modern control theory to observe internal and external perturbations. ADRC inherits the advantages of PID with little overshoot, high convergence speed, high accuracy, strong anti-interference ability and other characteristics, and it has a strong disturbance adaptability and robustness as for the uncertainty perturbation and their internal disturbance of control objects. Therefore, This paper attempts to use Active disturbance rejection control(ADRC, in order to improve the control of permanent magnet brushless motor. In this design of control system, the simulation of the system is realized based on MATLAB, and then the discrete control algorithm is transplanted to the embedded system to control the permanent magnet brushless DC motor (PMBLDCM. The control system is implemented on the DSP-F28335 digital signal processor, and the DSP also provides the functions like voltage and current AD sampling, PWM driver generation, speed and rotor position calculation, etc. The simulation and experiment results indicate that, the system has good dynamic performance and anti-disturbance performance.

  4. Monitoring and Control Interface Based on Virtual Sensors

    Directory of Open Access Journals (Sweden)

    Ricardo F. Escobar

    2014-10-01

    Full Text Available In this article, a toolbox based on a monitoring and control interface (MCI is presented and applied in a heat exchanger. The MCI was programed in order to realize sensor fault detection and isolation and fault tolerance using virtual sensors. The virtual sensors were designed from model-based high-gain observers. To develop the control task, different kinds of control laws were included in the monitoring and control interface. These control laws are PID, MPC and a non-linear model-based control law. The MCI helps to maintain the heat exchanger under operation, even if a temperature outlet sensor fault occurs; in the case of outlet temperature sensor failure, the MCI will display an alarm. The monitoring and control interface is used as a practical tool to support electronic engineering students with heat transfer and control concepts to be applied in a double-pipe heat exchanger pilot plant. The method aims to teach the students through the observation and manipulation of the main variables of the process and by the interaction with the monitoring and control interface (MCI developed in LabVIEW©. The MCI provides the electronic engineering students with the knowledge of heat exchanger behavior, since the interface is provided with a thermodynamic model that approximates the temperatures and the physical properties of the fluid (density and heat capacity. An advantage of the interface is the easy manipulation of the actuator for an automatic or manual operation. Another advantage of the monitoring and control interface is that all algorithms can be manipulated and modified by the users.

  5. Optimisation of Marine Boilers using Model-based Multivariable Control

    DEFF Research Database (Denmark)

    Solberg, Brian

    Traditionally, marine boilers have been controlled using classical single loop controllers. To optimise marine boiler performance, reduce new installation time and minimise the physical dimensions of these large steel constructions, a more comprehensive and coherent control strategy is needed. Th......). In the thesis the pressure control is based on this new method when on/off burner switching is required while the water level control is handled by a model predictive controller........ This research deals with the application of advanced control to a specific class of marine boilers combining well-known design methods for multivariable systems. This thesis presents contributions for modelling and control of the one-pass smoke tube marine boilers as well as for hybrid systems control. Much...... of the focus has been directed towards water level control which is complicated by the nature of the disturbances acting on the system as well as by low frequency sensor noise. This focus was motivated by an estimated large potential to minimise the boiler geometry by reducing water level fluctuations...

  6. Comparison of intelligent fuzzy based AGC coordinated PID controlled and PSS controlled AVR system

    Energy Technology Data Exchange (ETDEWEB)

    Mukherjee, V. [Department of Electrical Engineering, Asansol Engineering College, Asansol, West Bengal (India); Ghoshal, S.P. [Department of Electrical Engineering, National Institute of Technology, Durgapur, West Bengal (India)

    2007-11-15

    This paper attempts to investigate the performance of intelligent fuzzy based coordinated control of the Automatic Generation Control (AGC) loop and the excitation loop equipped with Proportional Integral Derivative (PID) controlled Automatic Voltage Regulator (AVR) system and Power System Stabilizer (PSS) controlled AVR system. The work establishes that PSS controlled AVR system is much more robust in dynamic performance of the system over a wide range of system operating configurations. Thus, it is revealed that PSS equipped AVR is much more superior than PID equipped AVR in damping the oscillation resulting in improved transient response. The paper utilizes a novel class of Particle Swarm Optimization (PSO) termed as Craziness based Particle Swarm Optimization (CRPSO) as optimizing tool to get optimal tuning of PSS parameters as well as the gains of PID controllers. For on-line, off-nominal operating conditions Takagi Sugeno Fuzzy Logic (TSFL) has been applied to obtain the off-nominal optimal gains of PID controllers and parameters of PSS. Implementation of TSFL helps to achieve very fast dynamic response. Fourth order model of generator with AVR and high gain thyristor excitation system is considered for PSS controlled system while normal gain exciter is considered for PID controlled system. Simulation study also reveals that with high gain exciter, PID control is not at all effective. Transient responses are achieved by using modal analysis. (author)

  7. Speed Control of Induction Motor Fed from Wind Turbine via Particle Swarm Optimization Based PI Controller

    Directory of Open Access Journals (Sweden)

    A.S. Oshaba

    2013-05-01

    Full Text Available Three-phase Induction Motor (IM is widely used in the industry because of its rugged construction and absence of brushes. However, speed control of IM is required depending on the desired speed and application. This study proposes a design of a Proportional Integral (PI controller using Particle Swarm Optimization (PSO algorithm to control the speed of an IM supplied from wind turbine. The wind turbine acts as a prime mover to a connected DC generator. Pulse Width Modulation (PWM is used to obtain three phase AC voltage from the output of DC generator. The proposed design problem of speed controller is formulated as an optimization problem. PSO is employed to search for optimal controller parameters by minimizing the time domain objective function. The performance of the proposed technique has been evaluated with respect to the variation of load torque and speed wind turbine. Also the performance of the proposed controller has been evaluated with the performance of the PI controller tuned by Genetic Algorithm (GA in order to demonstrate the superior efficiency of the proposed PSO in tuning PI controller. Simulation results emphasis on the better performance of the optimized PI controller based on PSO in compare to optimized PI controller based on GA over a wide range of load torque and speed wind turbine.

  8. Position Sensorless Control of IPMSMs Based on a Novel Flux Model Suitable for Maximum Torque Control

    Science.gov (United States)

    Matsumoto, Atsushi; Hasegawa, Masaru; Matsui, Keiju

    In this paper, a novel position sensorless control method for interior permanent magnet synchronous motors (IPMSMs) that is based on a novel flux model suitable for maximum torque control has been proposed. Maximum torque per ampere (MTPA) control is often utilized for driving IPMSMs with the maximum efficiency. In order to implement this control, generally, the parameters are required to be accurate. However, the inductance varies dramatically because of magnetic saturation, which has been one of the most important problems in recent years. Therefore, the conventional MTPA control method fails to achieve maximum efficiency for IPMSMs because of parameter mismatches. In this paper, first, a novel flux model has been proposed for realizing the position sensorless control of IPMSMs, which is insensitive to Lq. In addition, in this paper, it has been shown that the proposed flux model can approximately estimate the maximum torque control (MTC) frame, which as a new coordinate aligned with the current vector for MTPA control. Next, in this paper, a precise estimation method for the MTC frame has been proposed. By this method, highly accurate maximum torque control can be achieved. A decoupling control algorithm based on the proposed model has also been addressed in this paper. Finally, some experimental results demonstrate the feasibility and effectiveness of the proposed method.

  9. Neural network-based nonlinear model predictive control vs. linear quadratic gaussian control

    Science.gov (United States)

    Cho, C.; Vance, R.; Mardi, N.; Qian, Z.; Prisbrey, K.

    1997-01-01

    One problem with the application of neural networks to the multivariable control of mineral and extractive processes is determining whether and how to use them. The objective of this investigation was to compare neural network control to more conventional strategies and to determine if there are any advantages in using neural network control in terms of set-point tracking, rise time, settling time, disturbance rejection and other criteria. The procedure involved developing neural network controllers using both historical plant data and simulation models. Various control patterns were tried, including both inverse and direct neural network plant models. These were compared to state space controllers that are, by nature, linear. For grinding and leaching circuits, a nonlinear neural network-based model predictive control strategy was superior to a state space-based linear quadratic gaussian controller. The investigation pointed out the importance of incorporating state space into neural networks by making them recurrent, i.e., feeding certain output state variables into input nodes in the neural network. It was concluded that neural network controllers can have better disturbance rejection, set-point tracking, rise time, settling time and lower set-point overshoot, and it was also concluded that neural network controllers can be more reliable and easy to implement in complex, multivariable plants.

  10. Model-based dynamic control and optimization of gas networks

    Energy Technology Data Exchange (ETDEWEB)

    Hofsten, Kai

    2001-07-01

    by a structured sequential quadratic programming algorithm of Newton type. Each open loop problem is specified using a nonlinear prediction model. For each iteration of the quadratic programming procedure, a linear time variant prediction model is formulated. The suggested controller also handles time varying source capacity. Potential problems such as infeasibility and the security of the supply when facing a change in the status of the infrastructure of the transmission system under a transient customer load are treated. Comments on the infeasibility due to errors such as load forecast error, model error and state estimation error are also discussed. A simplified nonlinear model called the creep flow model is used to describe the fluid dynamics inside a natural gas transmission line. Different assumptions and reformulations of this model yield the different control, simulation and optimization models used in this thesis. The control of a single gas transmission line is investigated using linear model predictive control based on instant linearization of the nonlinear model. Model predictive control using a bi quadratic optimization model formulated from the creep flow model is also investigated. A distributed parameter control model of the gas dynamics for a transmission line is formulated. An analytic solution of this model is given with both Neuman boundary conditions and distributed supplies and loads. A transfer function model is developed expressing the dynamics between the defined output and the control and disturbance inputs of the transmission line. Based on the qualitative behaviour observed from the step responses of the solutions of the distributed parameter model formulated in this thesis, simplified transfer function models were developed. These control models expresses the dynamics of a natural gas transmission line with Neuman boundary control and load. Further, these models were used to design a control law, which is a combination of a Smith

  11. VFI-based Robotic Arm Control for Natural Adaptive Motion

    Directory of Open Access Journals (Sweden)

    Woosung Yang

    2014-03-01

    Full Text Available Since neural oscillator based control methods can generate rhythmic motion without information on system dynamics, they can be a promising alternative to traditional motion planning based control approaches. However, for field application, they still need to be robust against unexpected forces or changes in environments so as to be able to generate “natural motion” like most biological systems. In this study a biologically inspired control algorithm that combines neural oscillators and virtual force is proposed. This work gives the condition with respect to parameters tuning to stably activate the neural oscillators. This is helpful to achieve motion adaptability to environmental changes keeping the motion repeatability. He efficacy and efficiency of the proposed methods are tested in the control of a planar three-linkage robotic arm. It is shown that the proposed controller generates a given circular path stably and repeatedly, even with unexpected contact with a wall. The adaptivity of motion control is also tested in control of a robotic arm with redundant degrees of freedom. The proposed control algorithm works throughout the simulations and experiments.

  12. Control for Wind Power Generation Based on Inverse System Theory

    Directory of Open Access Journals (Sweden)

    Jiyong Zhang

    2013-11-01

    Full Text Available Traditional Double-fed Wind Generation systems are based on the vector control method, and it is dependent on motor parameters. The performance of the control system will be affected with the parameters changing,. This paper proposes a new control method based on inverse system and variable structure sliding mode(VSS theories, through the inverse system theory, the structure of its state’s equation, obtaining the structure of the inverse system, the establishment of Wind Power Generation closed-loop control system is established. The VSS controller, designed with exponential reaching law, can improve the dynamic performance in normal operation range effectively. When the system operates with variable speed constant frequency (VSCF and the phase voltage drops, the simulations show that the control system can control the DC link voltage steabily, maintain unity power factor, achieve the decoupling of the active and reactive power. And experiments show that the control method used in  VSCF wind power system is feasible.  

  13. GA-Based Fuzzy Sliding Mode Controller for Nonlinear Systems

    Directory of Open Access Journals (Sweden)

    W. L. Chiang

    2008-11-01

    Full Text Available Generally, the greatest difficulty encountered when designing a fuzzy sliding mode controller (FSMC or an adaptive fuzzy sliding mode controller (AFSMC capable of rapidly and efficiently controlling complex and nonlinear systems is how to select the most appropriate initial values for the parameter vector. In this paper, we describe a method of stability analysis for a GA-based reference adaptive fuzzy sliding model controller capable of handling these types of problems for a nonlinear system. First, we approximate and describe an uncertain and nonlinear plant for the tracking of a reference trajectory via a fuzzy model incorporating fuzzy logic control rules. Next, the initial values of the consequent parameter vector are decided via a genetic algorithm. After this, an adaptive fuzzy sliding model controller, designed to simultaneously stabilize and control the system, is derived. The stability of the nonlinear system is ensured by the derivation of the stability criterion based upon Lyapunov's direct method. Finally, an example, a numerical simulation, is provided to demonstrate the control methodology.

  14. Observer-Based Magnetic Bearing Controller Developed for Aerospace Flywheels

    Science.gov (United States)

    Le, Dzu K.; Provenza, Andrew J.

    2002-01-01

    A prototype of a versatile, observer-based magnetic bearing controller for aerospace flywheels was successfully developed and demonstrated on a magnetic bearing test rig (see the photograph) and an actual flywheel module. The objective of this development included a fast, yet low risk, control development process, and a robust, high-performance controller for a large variety of flywheels. This required a good system model, an efficient development procedure, and a model-based controller that addressed the key problems associated with flywheel and bearing imbalance, sensor error, and vibration. The model used in this control development and tuning procedure included the flexible rotor dynamics and motor-induced vibrations. Such a model was essential for low-risk scheduling of speed-dependent control parameters and for reliable evaluation of novel control strategies. The successfully tested control prototype utilized an extended Kalman filter to estimate the true rotor principal-axis motion from the raw sensor position feedback. For control refinement, the extended Kalman filter also estimated and eliminated the combined effects of mass-imbalance and sensor runouts from the input data. A key advantage of the design based on the extended Kalman filter is its ability to accurately estimate both the rotor's principal-axis position and gyroscopic rates with the least amount of phase lag. This is important for control parameter scheduling to dampen the gyroscopic motions. Because of large uncertainties in the magnetic bearing and imbalance characteristics, this state-estimation scheme alone is insufficient for containing the rotor motion within the desired 1-mil excursion radius. A nonlinear gain adjustment based on an estimation of the principal-axis orbit size was needed to provide a coarse (nonoptimal), but robust, control of the orbit growth. Control current minimization was achieved with a (steepest gradient) search of synchronous errors in the principal

  15. Application of Fuzzy Control with Market-Based Control Strategy to Structures

    Directory of Open Access Journals (Sweden)

    Gang Li

    2013-01-01

    Full Text Available The market-based control as a control strategy is developed based on an analogy between the control force-energy source in the structural area and the supply demand in the free market. The optimal problem of control force from an actuator is transformed to that of the allocation resource in the market. Since the supply-demand relation model and iteration procedure for the optimal price solution are necessary and relatively hard to understand and perform for civil engineers, the fuzzy logical method is proposed in the framework of the market-based control to acquire an equivalent system corresponding to the market-based control method. An equivalent fuzzy logical rule is established through analyzing a single-degree-of-freedom system with the controller using the MBC strategy under earthquakes. The results show that the fuzzy logical method is able to also reduce the displacement and acceleration responses effectively similar to the MBC method, and the consumed computational time for the fuzzy logical method is obviously saved.

  16. Stabilisation of difference equations with noisy prediction-based control

    Science.gov (United States)

    Braverman, E.; Kelly, C.; Rodkina, A.

    2016-07-01

    We consider the influence of stochastic perturbations on stability of a unique positive equilibrium of a difference equation subject to prediction-based control. These perturbations may be multiplicative We begin by relaxing the control parameter in the deterministic equation, and deriving a range of values for the parameter over which all solutions eventually enter an invariant interval. Then, by allowing the variation to be stochastic, we derive sufficient conditions (less restrictive than known ones for the unperturbed equation) under which the positive equilibrium will be globally a.s. asymptotically stable: i.e. the presence of noise improves the known effectiveness of prediction-based control. Finally, we show that systemic noise has a "blurring" effect on the positive equilibrium, which can be made arbitrarily small by controlling the noise intensity. Numerical examples illustrate our results.

  17. Design and performance comparison of fuzzy logic based tracking controllers

    Science.gov (United States)

    Lea, Robert N.; Jani, Yashvant

    1992-01-01

    Several camera tracking controllers based on fuzzy logic principles have been designed and tested in software simulation in the software technology branch at the Johnson Space Center. The fuzzy logic based controllers utilize range measurement and pixel positions from the image as input parameters and provide pan and tilt gimble rate commands as output. Two designs of the rulebase and tuning process applied to the membership functions are discussed in light of optimizing performance. Seven test cases have been designed to test the performance of the controllers for proximity operations where approaches like v-bar, fly-around and station keeping are performed. The controllers are compared in terms of responsiveness, and ability to maintain the object in the field-of-view of the camera. Advantages of the fuzzy logic approach with respect to the conventional approach have been discussed in terms of simplicity and robustness.

  18. A NEW ADMISSION CONTROL APPROACH BASED ON PREDICTION

    Institute of Scientific and Technical Information of China (English)

    Lu Kaining; Jin Zhigang; Zou Jun

    2002-01-01

    Admission control plays an important role in providing QoS to network users. Motivated by the measurement-based admission control algorithm, this letter proposed a new admission control approach for integrated service packet network based on traffic prediction. In the letter, FARIMA(p, d, q) models in the admission control algorithm is deployed. A method to simplify the FARIMA model fitting procedure and hence to reduce the time of traffic modeling and prediction is suggested. The feasibility-study experiments show that FARIMA models which have less number of parameters can be used to model and predict actual traffic on quite a large time scale. Simulation results validate the promising approach.

  19. Voice-Based Control of a DC Servo Motor

    Directory of Open Access Journals (Sweden)

    Musaab Hassan

    2012-01-01

    Full Text Available Problem statement: Motors play a very important role in our life and among which is the DC servo motors. The techniques of controlling these DC motors are plenty, among which is sound. In this study, a voce-based technique was implemented to control the speed and the direction of rotation for a DC motor. Approach: A Microcontroller-based electronic control circuit was designed and implemented to achieve this goal. Results: The speed of the motor was controlled, in both directions, using pulse width modulation and a microcontroller was used to generate the right signal to be applied to the motor. Conclusion: The loudness of human voice was successfully divided into different levels where each level drives the motor at different speed."

  20. Support vector machine-based multi-model predictive control

    Institute of Scientific and Technical Information of China (English)

    Zhejing BA; Youxian SUN

    2008-01-01

    In this paper,a support vector machine-based multi-model predictive control is proposed,in which SVM classification combines well with SVM regression.At first,each working environment is modeled by SVM regression and the support vector machine network-based model predictive control(SVMN-MPC)algorithm corresponding to each environment is developed,and then a multi-class SVM model is established to recognize multiple operating conditions.As for control,the current environment is identified by the multi-class SVM model and then the corresponding SVMN.MPCcontroller is activated at each sampling instant.The proposed modeling,switching and controller design is demonstrated in simulation results.

  1. PLC-Based Pressure Control in Multi-Pump Applications

    Directory of Open Access Journals (Sweden)

    Vodovozov Valery

    2015-12-01

    Full Text Available The paper is devoted to the centrifugal pumps represented the most popular type of pumping equipment used in different areas. The pressure control approach for variable speed driven (VSD parallel connected centrifugal pumps is reported. The goal of the study is optimization of some quality indices, such as efficiency, consumed power, productivity, energy carrier temperature, heat irradiation, etc. One of them – efficiency – has been studied in the paper more carefully. The mathematical model of pumping process is discussed and a vector-matrix description of the multi-pump application is given. The program-based pressure control system is developed which productivity is changed by regulating the number of working pumps. The paper introduces new pressure control algorithms based on the working point estimation intended for programmable logical controllers (PLC. Experiments prove correctness of the offered methodology.

  2. Study on Compensation Control of STATCOM Based on MMC

    Directory of Open Access Journals (Sweden)

    Xie Yan

    2016-01-01

    Full Text Available This paper introduced modular multi-level converter (MMC, which could enhance the voltage and power level by sub-converter modules in series and was easy to extend to any level of output. Its structure and working mechanism were described. By analyzing the energy transfer performance of STATCOM based on MMC working conditions in the compensation, a comprehensive compensation control strategy was proposed based on direct current control mode. By analyzing the higher harmonic components circulation generated by the inconsistencies in the three-phase upper and lower arm voltage, a loop control strategy is proposed for the suppression of the circulation in the arms of the M-STATCOM. The simulation results show the strategy has a better tracking precision and response speed for the compensation control.

  3. Energy-based robust controller design for flexible spacecraft

    Institute of Scientific and Technical Information of China (English)

    Shuzhi Sam GE; Tong Heng LEE; Fan HONG; Cher Hiang GOH

    2004-01-01

    This paper presents a class of non-model-based position controllers for a kind of flexible spacecraft. With the controllers, one can achieve not only the closed-loop stability of the original distributed parameter system, but also the asymptotic stability of the truncated system, which is obtained through representing the deflection of the appendage by an arbitrary finite number of flexible modes. The system dynamics are not explicitly involved in the controller design and stability proof. Instead, only a very basic system energy relationship of the flexible spacecraft is utilized. The controllers possess several remarkable advantages over the traditional model-based ones. Numerical simulations are carded out on a kind of spacecraft with one flexible appendage and satisfactory results are obtained.

  4. Configurable Embedded CPG-based Control for Robot Locomotion

    Directory of Open Access Journals (Sweden)

    Jose Hugo Barron-Zambrano

    2012-09-01

    Full Text Available Recently, the development of intelligent robots has benefited from a deeper understanding of the biomechanics and neurology of biological systems. Researchers have proposed the concept of Central Pattern Generators (CPGs as a mechanism for generating an efficient control strategy for legged robots based on biological locomotion principles. Although many studies have aimed to develop robust legged locomotion controllers, relatively few of them have focused on adopting the technology for fully practical embedded hardware implementations. In this contribution, a reconfigurable hardware implementation of a CPG‐based controller which is able to generate several gaits for quadruped and hexapod robots is presented. The proposed implementation is modular and configurable in order to scale up to legged robots with different degrees of freedom. Experimental results for embedded Field Programmable Gate Array (FPGA implementations for quadruped and hexapod robot controllers are presented and analysed.

  5. Owner-Based Role-Based Access Control OB-RBAC

    NARCIS (Netherlands)

    Saffarian, Mohsen; Sadighi, Babak

    2010-01-01

    Administration of an access control model deals with the question of who is authorized to update policies defined on the basis of that model. One of the models whose administration has absorbed relatively large research is the Role-Based Access Control (RBAC) model. All the existing role-based admin

  6. CONTROL OF NONLINEAR PROCESS USING NEURAL NETWORK BASED MODEL PREDICTIVE CONTROL

    Directory of Open Access Journals (Sweden)

    Dr.A.TRIVEDI

    2011-04-01

    Full Text Available This paper presents a Neural Network based Model Predictive Control (NNMPC strategy to control nonlinear process. Multilayer Perceptron Neural Network (MLP is chosen to represent a Nonlinear Auto Regressive with eXogenous signal (NARX model of a nonlinear system. NARX dynamic model is based on feed-forward architecture and offers good approximation capabilities along with robustness and accuracy. Based on the identified neural model, a generalized predictive control (GPC algorithm is implemented to control the composition in acontinuous stirred tank reactor (CSTR, whose parameters are optimally determined by solving quadratic performance index using well known Levenberg-Marquardt and Quasi-Newton algorithm. NNMPC is tuned by selecting few horizon parameters and weighting factor. The tracking performance of the NNMPC is tested using different amplitude function as a reference signal on CSTR application. Also the robustness and performance is tested in the presence of disturbance on random reference signal.

  7. Controlled cooling of an electronic system based on projected conditions

    Science.gov (United States)

    David, Milnes P.; Iyengar, Madhusudan K.; Schmidt, Roger R.

    2016-05-17

    Energy efficient control of a cooling system cooling an electronic system is provided based, in part, on projected conditions. The control includes automatically determining an adjusted control setting(s) for an adjustable cooling component(s) of the cooling system. The automatically determining is based, at least in part, on projected power consumed by the electronic system at a future time and projected temperature at the future time of a heat sink to which heat extracted is rejected. The automatically determining operates to reduce power consumption of the cooling system and/or the electronic system while ensuring that at least one targeted temperature associated with the cooling system or the electronic system is within a desired range. The automatically determining may be based, at least in part, on an experimentally obtained model(s) relating the targeted temperature and power consumption of the adjustable cooling component(s) of the cooling system.

  8. Tensor product model transformation based decoupled terminal sliding mode control

    Science.gov (United States)

    Zhao, Guoliang; Li, Hongxing; Song, Zhankui

    2016-06-01

    The main objective of this paper is to propose a tensor product model transformation based decoupled terminal sliding mode controller design methodology. The methodology is divided into two steps. In the first step, tensor product model transformation is applied to the single-input-multi-output system and a parameter-varying weighted linear time-invariant system is obtained. Then, decoupled terminal sliding mode controller is designed based on the linear time-invariant systems. The main novelty of this paper is that the nonsingular terminal sliding mode control design is based on a numerical model rather than an analytical one. Finally, simulations are tested on cart-pole system and translational oscillations with a rotational actuator system.

  9. Probabilistic performance-based design for high performance control systems

    Science.gov (United States)

    Micheli, Laura; Cao, Liang; Gong, Yongqiang; Cancelli, Alessandro; Laflamme, Simon; Alipour, Alice

    2017-04-01

    High performance control systems (HPCS) are advanced damping systems capable of high damping performance over a wide frequency bandwidth, ideal for mitigation of multi-hazards. They include active, semi-active, and hybrid damping systems. However, HPCS are more expensive than typical passive mitigation systems, rely on power and hardware (e.g., sensors, actuators) to operate, and require maintenance. In this paper, a life cycle cost analysis (LCA) approach is proposed to estimate the economic benefit these systems over the entire life of the structure. The novelty resides in the life cycle cost analysis in the performance based design (PBD) tailored to multi-level wind hazards. This yields a probabilistic performance-based design approach for HPCS. Numerical simulations are conducted on a building located in Boston, MA. LCA are conducted for passive control systems and HPCS, and the concept of controller robustness is demonstrated. Results highlight the promise of the proposed performance-based design procedure.

  10. Controlled cooling of an electronic system based on projected conditions

    Energy Technology Data Exchange (ETDEWEB)

    David, Milnes P.; Iyengar, Madhusudan K.; Schmidt, Roger R.

    2015-08-18

    Energy efficient control of a cooling system cooling an electronic system is provided based, in part, on projected conditions. The control includes automatically determining an adjusted control setting(s) for an adjustable cooling component(s) of the cooling system. The automatically determining is based, at least in part, on projected power consumed by the electronic system at a future time and projected temperature at the future time of a heat sink to which heat extracted is rejected. The automatically determining operates to reduce power consumption of the cooling system and/or the electronic system while ensuring that at least one targeted temperature associated with the cooling system or the electronic system is within a desired range. The automatically determining may be based, at least in part, on an experimentally obtained model(s) relating the targeted temperature and power consumption of the adjustable cooling component(s) of the cooling system.

  11. HOTELLING'S T2 CONTROL CHARTS BASED ON ROBUST ESTIMATORS

    Directory of Open Access Journals (Sweden)

    SERGIO YÁÑEZ

    2010-01-01

    Full Text Available Under the presence of multivariate outliers, in a Phase I analysis of historical set of data, the T 2 control chart based on the usual sample mean vector and sample variance covariance matrix performs poorly. Several alternative estimators have been proposed. Among them, estimators based on the minimum volume ellipsoid (MVE and the minimum covariance determinant (MCD are powerful in detecting a reasonable number of outliers. In this paper we propose a T 2 control chart using the biweight S estimators for the location and dispersion parameters when monitoring multivariate individual observations. Simulation studies show that this method outperforms the T 2 control chart based on MVE estimators for a small number of observations.

  12. Adaptive neural network consensus based control of robot formations

    Science.gov (United States)

    Guzey, H. M.; Sarangapani, Jagannathan

    2013-05-01

    In this paper, adaptive consensus based formation control scheme is derived for mobile robots in a pre-defined formation when full dynamics of the robots which include inertia, Corolis, and friction vector are considered. It is shown that dynamic uncertainties of robots can make overall formation unstable when traditional consensus scheme is utilized. In order to estimate the affine nonlinear robot dynamics, a NN based adaptive scheme is utilized. In addition to this adaptive feedback control input, an additional control input is introduced based on the consensus approach to make the robots keep their desired formation. Subsequently, the outer consensus loop is redesigned for reduced communication. Lyapunov theory is used to show the stability of overall system. Simulation results are included at the end.

  13. POWER CONTROL BASED COOPERATIVE OPPORTUNISTIC ROUTING IN WIRELESS SENSOR NETWORKS

    Institute of Scientific and Technical Information of China (English)

    Hu Haifeng; Zhu Qi

    2009-01-01

    This paper proposes an approach called PC-CORP (Power Control based Cooperative Opportunistic Routing Protocol) for WSN (Wireless Sensor Networks), providing robustness to the random variations in network connectivity while ensuring better data forwarding efficiency in an energy efficient manner. Based on the realistic radio model, we combine the region-based routing, rendezvous scheme, sleep discipline and cooperative communication together to model data forwarding by cross layer design in WSN. At the same time, a lightweight transmission power control algorithm called PC-AIMD (Power Control Additive Increase Multiplicative Decrease) is introduced to utilize the cooperation of relay nodes to improve the forwarding efficiency performance and increase the robustness of the routing protocol. In the simulation, the performance of PC-COPR is investigated in terms of the adaptation of variations in network connectivity and satisfying the QoS requirements of application.

  14. Time-Based Dithering Algorithm and Frame Rate Control Technique for STN LCD Controller

    Institute of Scientific and Technical Information of China (English)

    LEIJianming; ZOUXuechen

    2004-01-01

    Time-based dithering algorithm and Frame rate control (FRC) technique applied to the STN liquid crystal display controller are presented. The dithering unit performs time-based dithering algorithm on pixel data to advantageously increase smoothness of an image displayed. The frame rate control unit is responsive to the dithering unit and performs frame rate controlling to generate more gray-shades, which may reduce flicker and visual artifacts. Results show that the gray shades displayed on images can be up to 256 for monochrome STN LCD panels or 2563 colors for color STN LCD panels respectively by using timebased dithering algorithm and frame rate control technique if each encoded pixel data is 8 bits. The images displayed on the STN liquid crystal display can get desirable grayshades and very little flicker and visual artifacts.

  15. Decentralised stabilizing control based on H-infinity control theory making use of LMI

    Energy Technology Data Exchange (ETDEWEB)

    Niioka, S.; Yokoyama, R.; Ti, Z.X. [Tokyo Metropolitan University (Japan). Dept. of Electrical Engineering; Ishimaru, M.; Shirai, G. [Hosei University (Japan). Dept. of Electrical Engineering

    2000-07-01

    In this paper, two decentralized controller designs based on H{sub {infinity}} control theory are presented. In this controller design, LMI (Linear Matrix Inequality) is applied to obtain feedback gains for state feedback control. For an optimal linear regulator design, an index function of the quadratic form must be chosen. The question of how to decide weighting matrix in the quadratic index function used in Riccati equation arises. The problem is transformed into a pole allocation problem by making use of LMI. The effectiveness of the proposed method is shown by numerical simulations on a test system. (author)

  16. Controlled Interphase Power Controller (IPC on the Base of Squashed Transformer

    Directory of Open Access Journals (Sweden)

    AMBROS, T.

    2007-11-01

    Full Text Available One of the perspective technical decisions in the field of management of modes of the electrical networks and systems are the Flexible Alternating Power Transmission Systems (FACTS or Power Controllers. Most perspective of them is Interphase Power Controller (IPC on the base of non-controllable phase-shifting transformer with the three working windings connected in 'delta' and constant shifting angle of 600. The analyses of its characteristics and working modes which are done in this paper are shone, then using multi-windings controllable transformer allows essentially to damage the required power of the phase-shifting transformer.

  17. GENETIC ALGORITHM BASED PARAMETER TUNING OF PID CONTROLLER FOR COMPOSITION CONTROL SYSTEM

    Directory of Open Access Journals (Sweden)

    Bhawna Tandon

    2011-08-01

    Full Text Available A Composition control system is discussed in this paper in which the PID controller is tuned using Genetic Algorithm & Ziegler-Nichols Tuning Criteria. Tuning methods for PID controllers are very importantfor the process industries. Traditional methods such as Ziegler-Nichols method often do not provide adequate tuning. Genetic Algorithm (GA as an intelligent approach has also been widely used to tune the parameters of PID. Genetic algorithms are used to create an objective function that can evaluate the optimum PID gains based on the controlled systems overall error.

  18. Temporal Difference based Tuning of Fuzzy Logic Controller through Reinforcement Learning to Control an Inverted Pendulum

    Directory of Open Access Journals (Sweden)

    Raj kumar

    2012-08-01

    Full Text Available This paper presents a self-tuning method of fuzzy logic controllers. The consequence part of the fuzzy logic controller is self-tuned through the Q-learning algorithm of reinforcement learning. The off policy temporal difference algorithm is used for tuning which directly approximate the action value function which gives the maximum reward. In this way, the Q-learning algorithm is used for the continuous time environment. The approach considered is having the advantage of fuzzy logic controller in a way that it is robust under the environmental uncertainties and no expert knowledge is required to design the rule base of the fuzzy logic controller.

  19. Safety control program for complex system based on behavior science

    Institute of Scientific and Technical Information of China (English)

    LIANG Mei-jian; YANG Guang; CHEN Da-wei

    2008-01-01

    To control complex system's safety effectively,safety control program was supported based on the principles of behavioral science that shapes organizational behavior,and organizational behavior produced individual behavior.The program can be structured into a model that consists of three modules including individual behavior rectification,organization behavior diagnosis and model of safety culture.The research result not only reveals the deep cause of complex system accidents but also provides structural descriptions with the accidents cause.

  20. Safety control program for complex system based on behavior science

    Institute of Scientific and Technical Information of China (English)

    LIANG Mei-jian; YANG Guang; CHEN Da-wei

    2008-01-01

    To control complex system's safety effectively, safety control program was supported based on the principles of behavioral science that shapes organizational be-havior, and organizational behavior produced individual behavior. The program can be structured into a model that consists of three modules including individual behavior rectifi-cation, organization behavior diagnosis and model of safety culture. The research result not only reveals the deep cause of complex system accidents but also provides structural descriptions with the accidents cause.

  1. Control System for a Diesel Generator and UPS Based Microgrid

    Science.gov (United States)

    Palamar, Andriy; Pettai, Elmo; Beldjajev, Viktor

    2010-01-01

    In this paper a microgrid composed of a diesel generator and two uninterruptible power supply systems with separate battery banks is introduced. The microgrid located in three academic buildings of Tallinn University of Technology. A three-level control and monitoring system for the microgrid based on the EtherNet/IP communication network is developed. In addition, a control strategy of the microgrid in the grid-connected and stand-alone mode of operation is proposed.

  2. Stabilization of discrete nonlinear systems based on control Lyapunov functions

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The stabilization of discrete nonlinear systems is studied.Based on control Lyapunov functions,asufficient and necessary condition for a quadratic function to be a control Lyapunov function is given.From this condition,a continuous state feedback law is constructed explicitly.It can globally asymptotically stabilize the equilibrium of the closed-loop system.A simulation example shows the effectiveness of the proposed method.

  3. Control System for a Diesel Generator and UPS Based Microgrid

    OpenAIRE

    Palamar, A; Pettai, E; Beldjajev, v

    2010-01-01

    In this paper a microgrid composed of a diesel generator and two uninterruptible power supply systems with separate battery banks is introduced. The microgrid located in three academic buildings of Tallinn University of Technology. A three-level control and monitoring system for the microgrid based on the EtherNet/IP communication network is developed. In addition, a control strategy of the microgrid in the grid-connected and stand-alone mode of operation is proposed

  4. Aeroservoelastic model based active control for large civil aircraft

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    A modeling and control approach for an advanced configured large civil aircraft with aeroservoelasticity via the LQG method and control allocation is presented.Mathematical models and implementation issues for the multi-input/multi-output(MIMO) aeroservoelastic system simulation developed for a flexible wing with multi control surfaces are described.A fuzzy logic based optimization approach is employed to solve the constrained control allocation problem via intelligently adjusting the components of output vector and find a proper vector in the attainable moment set(AMS) autonomously.The basic idea is to minimize the L2 norm of error between the desired moment and achievable moment using the designing freedom provided by redundantly allocated actuators and control surfaces.Considering the constraints of control surfaces,in order to obtain acceptable performance of aircraft such as stability and maneuverability,the fuzzy weights are updated by the learning algorithm,which makes the closed-loop system self-adaptation.Finally,an application example of flight control designing for the advanced civil aircraft is discussed as a demonstration.The studies we have performed showed that the advanced configured large civil aircraft has good performance with the proper designed control law designed via the proposed approach.The gust alleviation and flutter suppression are applied with the synergetic effects of elevator,ailerons,equivalent rudders and flaps.The results show good closed loop performance and meet the requirement of constraint of control surfaces.

  5. A rule-based neural controller for inverted pendulum system.

    Science.gov (United States)

    Hao, J; Vandewalle, J; Tan, S

    1993-03-01

    This paper tries to demonstrate how a heuristic neural control approach can be used to solve a complex nonlinear control problem. The control task is to swing up a pendulum mounted on a cart from its stable position (vertically down) to the zero state (up right) and keep it there by applying a sequence of two opposing constant forces of equal magnitude to the mass center of the cart. In addition, the displacement of the cart itself is confined to within a preset limit during the swinging up action and it will eventually be brought to the origin of the track. This is truly a nontrivial nonlinear regulation problem and is considerably difficult compared to the pendulum balancing problem (and its variations) widely adopted as a benchmarking test system for neural controllers. Through the solution of this specific control problem, we try to illustrate a heuristic neural control approach with task decomposition, control rule extraction and neural net rule implementation as its basic elements. Specializing to the pendulum problem, the global control task is decomposed into subtasks namely pendulum positioning and cart positioning. Accordingly, three separate neural subcontrollers are designed to cater to the subtasks and their coordination, i.e., pendulum subcontroller (PSC), cart subcontroller (CSC) and the switching subcontroller (SSC). Each of the subcontrollers is designed based on the rules and guidelines obtained from the experiences of a human operator. The simulation result is included to show the actual performance of the controller.

  6. Research on Canal System Operation Based on Controlled Volume Method

    Directory of Open Access Journals (Sweden)

    Zhiliang Ding

    2009-10-01

    Full Text Available An operating simulation mode based on storage volume control method for multireach canal system in series was established. In allusion to the deficiency of existing controlled volume algorithm, the improved algorithm was proposed, that is the controlled volume algorithm of whole canal pools, the simulation results indicate that the storage volume and water level of each canal pool can be accurately controlled after the improved algorithm was adopted. However, for some typical discharge demand change operating conditions of canal, if the controlled volume algorithm of whole canal pool is still adopted, then it certainly will cause some unnecessary regulation, and consequently increases the disturbed canal reaches. Therefor, the idea of controlled volume operation method of continuous canal pools was proposed, and its algorithm was designed. Through simulation to practical project, the results indicate that the new controlled volume algorithm proposed for typical operating condition can comparatively obviously reduce the number of regulated check gates and disturbed canal pools for some typical discharge demand change operating conditions of canal, thus the control efficiency of canal system was improved. The controlled volume method of operation is specially suitable for large-scale water delivery canal system which possesses complex operation requirements.

  7. Information distribution in distributed microprocessor based flight control systems

    Science.gov (United States)

    Montgomery, R. C.; Lee, P. S.

    1977-01-01

    This paper presents an optimal control theory that accounts for variable time intervals in the information distribution to control effectors in a distributed microprocessor based flight control system. The theory is developed using a linear process model for the aircraft dynamics and the information distribution process is modeled as a variable time increment process where, at the time that information is supplied to the control effectors, the control effectors know the time of the next information update only in a stochastic sense. An optimal control problem is formulated and solved that provides the control law that minimizes the expected value of a quadratic cost function. An example is presented where the theory is applied to the control of the longitudinal motions of the F8-DFBW aircraft. Theoretical and simulation results indicate that, for the example problem, the optimal cost obtained using a variable time increment Markov information update process where the control effectors know only the past information update intervals and the Markov transition mechanism is almost identical to that obtained using a known uniform information update interval.

  8. Composite control for raymond mill based on model predictive control and disturbance observer

    Directory of Open Access Journals (Sweden)

    Dan Niu

    2016-03-01

    Full Text Available In the raymond mill grinding process, precise control of operating load is vital for the high product quality. However, strong external disturbances, such as variations of ore size and ore hardness, usually cause great performance degradation. It is not easy to control the current of raymond mill constant. Several control strategies have been proposed. However, most of them (such as proportional–integral–derivative and model predictive control reject disturbances just through feedback regulation, which may lead to poor control performance in the presence of strong disturbances. For improving disturbance rejection, a control method based on model predictive control and disturbance observer is put forward in this article. The scheme employs disturbance observer as feedforward compensation and model predictive control controller as feedback regulation. The test results illustrate that compared with model predictive control method, the proposed disturbance observer–model predictive control method can obtain significant superiority in disturbance rejection, such as shorter settling time and smaller peak overshoot under strong disturbances.

  9. A comprehensive gaze stabilization controller based on cerebellar internal models

    DEFF Research Database (Denmark)

    Vannucci, Lorenzo; Falotico, Egidio; Tolu, Silvia

    2017-01-01

    based on the coordination of VCR and VOR and OKR. The model, inspired by neuroscientific cerebellar theories, is provided with learning and adaptation capabilities based on internal models. We present the results for the gaze stabilization model on three sets of experiments conducted on the SABIAN robot...... and on the iCub simulator, validating the robustness of the proposed control method. The first set of experiments focused on the controller response to a set of disturbance frequencies along the vertical plane. The second shows the performances of the system under three-dimensional disturbances. The last set...

  10. On PID Controller Design Using Knowledge Based Fuzzy System

    Directory of Open Access Journals (Sweden)

    Jana Nowakova

    2012-01-01

    Full Text Available The designing of PID controllers is a frequently discussed problem. Many of design methods have been developed, classic (analytical tuning methods, optimization methods etc. or not so common fuzzy knowledge based methods which are designed to achieve good setpoint following, corresponding time response etc. In this case, the new way of designing PID controller parameters is created where the above mentioned knowledge system based on relations of Ziegler-Nichols design methods is used, more precisely the combination of the both Ziegler-Nichols methods. The proof of efficiency of a proposed method and a numerical experiment is presented.

  11. Privacy Preservation in Role-based Access Control Model

    Directory of Open Access Journals (Sweden)

    Zuo Chen

    2011-08-01

    Full Text Available Privacy preservation is a crucial problem in resource sharing and collaborating among multi-domains. Based on this problem, we propose a role-based access control model for privacy preservation. This scheme avoided the privacy leakage of resources while implementing access control, and it has the advantage of lower communication overhead. We demonstrate this scheme meets the IND-CCA2 semantic security by using random oracle. The simulation result shows this scheme has better execution efficiency and application effects.

  12. Design of Piston Air Compressor Unit Control System based Converter

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    <正>Based on the running characteristics and high energy consumption of air compressors in coal mines,an air pressure PID closed loop control system has been designed in this paper.The system is composed of PLC, converter and sensors etc and adopts the control method of converter triple-evaporator which makes air supply"need-based".The designed system has been applied in multiple coal mines and the results show its energy saving is remarkable and potential application is widely.

  13. Artificial Intelligence Based Alum Dosage Control in Water Treatment Plant

    Directory of Open Access Journals (Sweden)

    P Poongodi

    2013-08-01

    Full Text Available Supplying good quality of drinking water is a challenging task during the rainy season and floods. During this period water becomes highly polluted with suspended solids which increase the water turbidity. Alum is used to reduce the turbidity of the water. Typically in water treatment plants alum dosage is decided by the Jar test and the desired alum dosage is added manually. This research proposes an automatic alum dosage mixing process. The alum dosage is controlled by an intelligent controller which consists of a dosage predictor, an inverse model of the dosage pump and a Pulse Width Modulation (PWM controller. The optimal alum dosage is predicted by the dosage predictor. The PWM controller controls the flow rate of the alum dosing pump. This proposed method has been implemented in a laboratory based water treatment plant and it ensures the automation in water treatment plant to supply good quality drinking water.

  14. Intelligent control based on fuzzy logic and neural net theory

    Science.gov (United States)

    Lee, Chuen-Chien

    1991-01-01

    In the conception and design of intelligent systems, one promising direction involves the use of fuzzy logic and neural network theory to enhance such systems' capability to learn from experience and adapt to changes in an environment of uncertainty and imprecision. Here, an intelligent control scheme is explored by integrating these multidisciplinary techniques. A self-learning system is proposed as an intelligent controller for dynamical processes, employing a control policy which evolves and improves automatically. One key component of the intelligent system is a fuzzy logic-based system which emulates human decision making behavior. It is shown that the system can solve a fairly difficult control learning problem. Simulation results demonstrate that improved learning performance can be achieved in relation to previously described systems employing bang-bang control. The proposed system is relatively insensitive to variations in the parameters of the system environment.

  15. Research on DSP-based Asynchronous Motor Control Technology

    Directory of Open Access Journals (Sweden)

    Jun Yao

    2013-05-01

    Full Text Available The Motor in a variety of electrical transmission and position servo system occupies an extremely important position. After the DSP technology being applied to the motor control, the unification of the hardware and the flexibility of the software can be combined. Take the brushless DC motor for example, studied the mathematical model and the structure of the motor control system, also obtained the design scheme of the DSP-based asynchronous motor control system. With TI's 32 bit fixed point DSPTMS320F2812 as the core design of the hardware system, we wrote the system software, debug the motor control system and the results show that the system achieves the expected effect. The results of the research can be applied to brushless DC motor and other motor control, it will have a wide application prospects.

  16. Clonal Selection Algorithm Based Iterative Learning Control with Random Disturbance

    Directory of Open Access Journals (Sweden)

    Yuanyuan Ju

    2013-01-01

    Full Text Available Clonal selection algorithm is improved and proposed as a method to solve optimization problems in iterative learning control. And a clonal selection algorithm based optimal iterative learning control algorithm with random disturbance is proposed. In the algorithm, at the same time, the size of the search space is decreased and the convergence speed of the algorithm is increased. In addition a model modifying device is used in the algorithm to cope with the uncertainty in the plant model. In addition a model is used in the algorithm cope with the uncertainty in the plant model. Simulations show that the convergence speed is satisfactory regardless of whether or not the plant model is precise nonlinear plants. The simulation test verify the controlled system with random disturbance can reached to stability by using improved iterative learning control law but not the traditional control law.

  17. A hybrid joint based controller for an upper extremity exoskeleton

    Science.gov (United States)

    Mohd Khairuddin, Ismail; Taha, Zahari; Majeed, Anwar P. P. Abdul; Hakeem Deboucha, Abdel; Azraai Mohd Razman, Mohd; Aziz Jaafar, Abdul; Mohamed, Zulkifli

    2016-02-01

    This paper presents the modelling and control of a two degree of freedom upper extremity exoskeleton. The Euler-Lagrange formulation was used in deriving the dynamic modelling of both the human upper limb as well as the exoskeleton that consists of the upper arm and the forearm. The human model is based on anthropometrical measurements of the upper limb. The proportional-derivative (PD) computed torque control (CTC) architecture is employed in this study to investigate its efficacy performing joint-space control objectives specifically in rehabilitating the elbow and shoulder joints along the sagittal plane. An active force control (AFC) algorithm is also incorporated into the PD-CTC to investigate the effectiveness of this hybrid system in compensating disturbances. It was found that the AFC- PD-CTC performs well against the disturbances introduced into the system whilst achieving acceptable trajectory tracking as compared to the conventional PD-CTC control architecture.

  18. Laser vision based adaptive fill control system for TIG welding

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The variation of joint groove size during tungsten inert gas (TIG) welding will result in the non-uniform fill of deposited metal. To solve this problem, an adaptive fill control system was developed based on laser vision sensing. The system hardware consists of a modular development kit (MDK) as the real-time image capturing system, a computer as the controller, a D/A conversion card as the interface of controlled variable output, and a DC TIG welding system as the controlled device. The system software is developed and the developed feature extraction algorithm and control strategy are of good accuracy and robustness. Experimental results show that the system can implement adaptive fill of melting metal with high stability, reliability and accuracy. The groove is filled well and the quality of the weld formation satisfies the relevant industry criteria.

  19. Engine control system having pressure-based timing

    Science.gov (United States)

    Willi, Martin L.; Fiveland, Scott B.; Montgomery, David T.; Gong, Weidong

    2011-10-04

    A control system for an engine having a first cylinder and a second cylinder is disclosed having a first engine valve movable to regulate a fluid flow of the first cylinder and a first actuator associated with the first engine valve. The control system also has a second engine valve movable to regulate a fluid flow of the second cylinder and a sensor configured to generate a signal indicative of a pressure within the first cylinder. The control system also has a controller that is in communication with the first actuator and the sensor. The controller is configured to compare the pressure within the first cylinder with a desired pressure and selectively regulate the first actuator to adjust a timing of the first engine valve independently of the timing of the second engine valve based on the comparison.

  20. Google glass-based remote control of a mobile robot

    Science.gov (United States)

    Yu, Song; Wen, Xi; Li, Wei; Chen, Genshe

    2016-05-01

    In this paper, we present an approach to remote control of a mobile robot via a Google Glass with the multi-function and compact size. This wearable device provides a new human-machine interface (HMI) to control a robot without need for a regular computer monitor because the Google Glass micro projector is able to display live videos around robot environments. In doing it, we first develop a protocol to establish WI-FI connection between Google Glass and a robot and then implement five types of robot behaviors: Moving Forward, Turning Left, Turning Right, Taking Pause, and Moving Backward, which are controlled by sliding and clicking the touchpad located on the right side of the temple. In order to demonstrate the effectiveness of the proposed Google Glass-based remote control system, we navigate a virtual Surveyor robot to pass a maze. Experimental results demonstrate that the proposed control system achieves the desired performance.

  1. Attribute Control Chart Construction Based on Fuzzy Score Number

    Directory of Open Access Journals (Sweden)

    Shiwang Hou

    2016-11-01

    Full Text Available There is much uncertainty and fuzziness in product quality attributes or quality parameters of a manufacturing process, so the traditional quality control chart can be difficult to apply. This paper proposes a fuzzy control chart. The plotted data was obtained by transforming expert scores into fuzzy numbers. Two types of nonconformity judgment rules—necessity and possibility measurement rules—are proposed. Through graphical analysis, the nonconformity judging method (i.e., assessing directly based on the shape feature of a fuzzy control chart is proposed. For four different widely used membership functions, control levels were analyzed and compared by observing gaps between the upper and lower control limits. The result of the case study validates the feasibility and reliability of the proposed approach.

  2. Efficient community-based control strategies in adaptive networks

    CERN Document Server

    Yang, Hui; Zhang, Hai-Feng

    2012-01-01

    Most researches on adaptive networks mainly concentrate on the properties of steady state, but neglect transient dynamics. In this study, we pay attention to the emergence of community structures in transient process and the effects of community-based control strategies on epidemic spreading. First, by normalizing modularity $Q$, we investigate the evolution of community structures during the transient process, and find that very strong community structures are induced by rewiring mechanism in the early stage of epidemic spreading, which remarkably delays the outbreaks of epidemic. Then we study the effects of control strategies started from different stages on the prevalence. Both immunization and quarantine strategies indicate that it is not "the earlier, the better" for the implementing of control measures. And the optimal control effect is obtained if control measures can be efficiently implemented in the period of strong community structure. For immunization strategy, immunizing the S nodes on SI links a...

  3. Provably Safe and Robust Learning-Based Model Predictive Control

    CERN Document Server

    Aswani, Anil; Sastry, S Shankar; Tomlin, Claire

    2011-01-01

    Controller design for systems typically faces a trade-off between robustness and performance, and the reliability of linear controllers has caused many control practitioners to focus on the former. However, there is a renewed interest in improving system performance to deal with growing energy and pollution constraints. This paper describes a learning-based model predictive control (MPC) scheme. The MPC provides deterministic guarantees on robustness and safety, and the learning is used to identify richer models of the system to improve controller performance. Our scheme uses a linear model with bounds on its uncertainty to construct invariant sets which help to provide the guarantees, and it can be generalized to other classes of models and to pseudo-spectral methods. This framework allows us to handle state and input constraints and optimize system performance with respect to a cost function. The learning occurs through the use of an oracle which returns the value and gradient of unmodeled dynamics at discr...

  4. The cycloconverter based on fuzzy controller for lift

    Institute of Scientific and Technical Information of China (English)

    WANG Gen-ping; YI Ling-zhi

    2005-01-01

    In order to ensure the lift can go up and down steadily and safely, a cycloconverter based on fuzzy control algorithm for lift was introduced, which can keep the output voltage to be symmetric sine wave. In this cycloconverter system,the main circuit structure was designed as circumfluence mode, with the strong DSP as the control unit, the fuzzy control policy of average weight accumulation decision was used to control the tuning of the triggering angle for thyristor in the main circuit, and then,the output voltage of the cycloconverter can be controlled. The experiment and simulation prove that the performance of the fuzzy cycloconverter is improved a lot and the output voltage is very similar to symmetric sine wave. This kind of cycloconverter can help the lift stop accurately, and the shock can be decreased.

  5. FPGA-based Controller for a Mobile Robot

    CERN Document Server

    Kale, Shilpa

    2009-01-01

    With application in the robotics and automation, more and more it becomes necessary the development of applications based on methodologies that facilitate future modifications, updates and enhancements in the original projected system. This project presents a conception of mobile robots using rapid prototyping, distributing the several control actions in growing levels of complexity and computing proposal oriented to embed systems implementation. This kind of controller can be tested on different platform representing the mobile robots using reprogrammable logic components (FPGA). This mobile robot will detect obstacle and also be able to control the speed. Different modules will be Actuators, Sensors, wireless transmission. All this modules will be interfaced using FPGA controller. I would like to construct a mechanically simple robot model, which can measure the distance from obstacle with the aid of sensor and accordingly should able to control the speed of motor. I would like to construct a mechanically s...

  6. Quantum synchronization in an optomechanical system based on Lyapunov control.

    Science.gov (United States)

    Li, Wenlin; Li, Chong; Song, Heshan

    2016-06-01

    We extend the concepts of quantum complete synchronization and phase synchronization, which were proposed in A. Mari et al., Phys. Rev. Lett. 111, 103605 (2013)PRLTAO0031-900710.1103/PhysRevLett.111.103605, to more widespread quantum generalized synchronization. Generalized synchronization can be considered a necessary condition or a more flexible derivative of complete synchronization, and its criterion and synchronization measure are proposed and analyzed in this paper. As examples, we consider two typical generalized synchronizations in a designed optomechanical system. Unlike the effort to construct a special coupling synchronization system, we purposefully design extra control fields based on Lyapunov control theory. We find that the Lyapunov function can adapt to more flexible control objectives, which is more suitable for generalized synchronization control, and the control fields can be achieved simply with a time-variant voltage. Finally, the existence of quantum entanglement in different generalized synchronizations is also discussed.

  7. Coordinating control of multiple rigid bodies based on motion primitives

    Institute of Scientific and Technical Information of China (English)

    Fan Wu; Zhi-Yong Geng

    2012-01-01

    This paper studies the problem of coordinated motion generation for a group of rigid bodies.Two classes of coordinated motion primitives,relative equilibria and maneuvers,are given as building blocks for generating coordinated motions.In a motion-primitive based planning framework,a control method is proposed for the robust execution of a coordinated motion plan in the presence of perturbations,The control method combines the relative equilibria stabilization with maneuver design,and results in a closeloop motion planning framework.The performance of the control method has been illustrated through a numerical simulation.

  8. GPS Based Autonomous Flight Control System for an Unmanned Airship

    Directory of Open Access Journals (Sweden)

    Vishnu G Nair,

    2014-01-01

    Full Text Available An unmanned airship, also known as a Unmanned aircraft System (UAS or a remotely piloted aircraft is a machine which functions either by the remote control of a navigator or pilot. The unmanned airship uses the autonomous flight, navigation and guidance based on the telemetry command of ground station. The Autonomous Flight Control System (AFCS [1] plays a key role in achieving the given requirements and missions. This paper introduces the overall design architecture of the hardware and software of the flight control systems in a 50m long unmanned airship

  9. Controlling Chaos in Neuron Based on Lasalle Invariance Principle

    Science.gov (United States)

    Wei, Du-Qu; Qin, Ying-Hua

    2011-09-01

    A new control law is proposed to asymptotically stabilize the chaotic neuron system based on LaSalle invariant principle. The control technique does not require analytical knowledge of the system dynamics and operates without an explicit knowledge of the desired steady-state position. The well-known modified Hodgkin—Huxley (MHH) and Hindmarsh—Rose (HR) model neurons are taken as examples to verify the implementation of our method. Simulation results show the proposed control law is effective. The outcome of this study is significant since it is helpful to understand the learning process of a human brain towards the information processing, memory and abnormal discharge of the brain neurons.

  10. Intelligent Transportation Control based on Proactive Complex Event Processing

    Directory of Open Access Journals (Sweden)

    Wang Yongheng

    2016-01-01

    Full Text Available Complex Event Processing (CEP has become the key part of Internet of Things (IoT. Proactive CEP can predict future system states and execute some actions to avoid unwanted states which brings new hope to intelligent transportation control. In this paper, we propose a proactive CEP architecture and method for intelligent transportation control. Based on basic CEP technology and predictive analytic technology, a networked distributed Markov decision processes model with predicting states is proposed as sequential decision model. A Q-learning method is proposed for this model. The experimental evaluations show that this method works well when used to control congestion in in intelligent transportation systems.

  11. Stabilization of nonlinear systems based on robust control Lyapunov function

    Institute of Scientific and Technical Information of China (English)

    CAI Xiu-shan; HAN Zheng-zhi; LU Gan-yun

    2007-01-01

    This paper deals with the robust stabilization problem for a class of nonlinear systems with structural uncertainty. Based on robust control Lyapunov function, a sufficient and necessary condition for a function to be a robust control Lyapunov function is given. From this condition, simply sufficient condition for the robust stabilization (robust practical stabilization) is deduced. Moreover, if the equilibrium of the closed-loop system is unique, the existence of such a robust control Lyapunov function will also imply robustly globally asymptotical stabilization. Then a continuous state feedback law can be constructed explicitly. The simulation shows the effectiveness of the method.

  12. The CASCAM network control system based on TCP/IP

    Science.gov (United States)

    Ren, S. B.; Yao, Y. Q.; Yao, D. Z.

    2004-05-01

    The paper presents the CASCAM network control system based on the TCP/IP protocol. In order to realize the Client/Server model in network communication between the workstation and personal computer efficiently, two C++ classes, client and server, were developed in the system. The script language Tcl/Tk was used in programming the system control pane in the Client. With loading the dynamic library, the Client sends the request to the Server through the network, then the Server analyzes the request and controls the camera system.

  13. A multiparameter chaos control method based on OGY approach

    Energy Technology Data Exchange (ETDEWEB)

    Souza de Paula, Aline [Universidade Federal do Rio de Janeiro, COPPE - Department of Mechanical Engineering, 21.941.972 - Rio de Janeiro - RJ, P.O. Box 68.503 (Brazil)], E-mail: alinesp@ufrj.br; Amorim Savi, Marcelo [Universidade Federal do Rio de Janeiro, COPPE - Department of Mechanical Engineering, 21.941.972 - Rio de Janeiro - RJ, P.O. Box 68.503 (Brazil)], E-mail: savi@mecanica.ufrj.br

    2009-05-15

    Chaos control is based on the richness of responses of chaotic behavior and may be understood as the use of tiny perturbations for the stabilization of a UPO embedded in a chaotic attractor. Since one of these UPO can provide better performance than others in a particular situation the use of chaos control can make this kind of behavior to be desirable in a variety of applications. The OGY method is a discrete technique that considers small perturbations promoted in the neighborhood of the desired orbit when the trajectory crosses a specific surface, such as a Poincare section. This contribution proposes a multiparameter semi-continuous method based on OGY approach in order to control chaotic behavior. Two different approaches are possible with this method: coupled approach, where all control parameters influences system dynamics although they are not active; and uncoupled approach that is a particular case where control parameters return to the reference value when they become passive parameters. As an application of the general formulation, it is investigated a two-parameter actuation of a nonlinear pendulum control employing coupled and uncoupled approaches. Analyses are carried out considering signals that are generated by numerical integration of the mathematical model using experimentally identified parameters. Results show that the procedure can be a good alternative for chaos control since it provides a more effective UPO stabilization than the classical single-parameter approach.

  14. Integrated software environment dedicated for implementation of control systems based on PLC controllers

    Directory of Open Access Journals (Sweden)

    Szymon SURMA

    2007-01-01

    Full Text Available Industrial processes’ control systems based on PLC controllers play today a very important role in all fields of transport, including also sea transport. Construction of control systems is the field of engineering, which has been continuously evolving towards maximum simplification of system design path. Up to now the time needed forthe system construction from the design to commissioning had to be divided into a few stages. A mistake made in an earlier stage caused that in most cases the next stages had to be restarted. Available debugging systems allows defect detection at an early stage of theproject implementation. The paper presents general characteristic of integrated software for implementation of complex control systems. The issues related to the software use for programming of the visualisation environment, control computer, selection oftransmission medium and transmission protocol as well as PLC controllers’ configuration, software and control have been analysed.

  15. Optimized Aircraft Electric Control System Based on Adaptive Tabu Search Algorithm and Fuzzy Logic Control

    Directory of Open Access Journals (Sweden)

    Saifullah Khalid

    2016-09-01

    Full Text Available Three conventional control constant instantaneous power control, sinusoidal current control, and synchronous reference frame techniques for extracting reference currents for shunt active power filters have been optimized using Fuzzy Logic control and Adaptive Tabu search Algorithm and their performances have been compared. Critical analysis of Comparison of the compensation ability of different control strategies based on THD and speed will be done, and suggestions will be given for the selection of technique to be used. The simulated results using MATLAB model are presented, and they will clearly prove the value of the proposed control method of aircraft shunt APF. The waveforms observed after the application of filter will be having the harmonics within the limits and the power quality will be improved.

  16. Differential-Drive Mobile Robot Control Design based-on Linear Feedback Control Law

    Science.gov (United States)

    Nurmaini, Siti; Dewi, Kemala; Tutuko, Bambang

    2017-04-01

    This paper deals with the problem of how to control differential driven mobile robot with simple control law. When mobile robot moves from one position to another to achieve a position destination, it always produce some errors. Therefore, a mobile robot requires a certain control law to drive the robot’s movement to the position destination with a smallest possible error. In this paper, in order to reduce position error, a linear feedback control is proposed with pole placement approach to regulate the polynoms desired. The presented work leads to an improved understanding of differential-drive mobile robot (DDMR)-based kinematics equation, which will assist to design of suitable controllers for DDMR movement. The result show by using the linier feedback control method with pole placement approach the position error is reduced and fast convergence is achieved.

  17. Intelligent robust control law for induction motors based on field-oriented control theory

    Energy Technology Data Exchange (ETDEWEB)

    Barambones, O.; Alcorta, P.; Sevillano, G.; Garrido, A.; Garrido, I. [Univ. del Pais Vasco, Bilbao (Spain). Dpto. Ingenieri a de Sistemas y Automatica

    2009-07-01

    A sensorless adaptive control law was developed to improve the trajectory tracking performance of induction motors. The law used an integral sliding mode algorithm to avoid the necessity of calculating an upper bound for system uncertainties. The vector control theory was used to develop the induction motor drives. The sliding mode control law incorporated an adaptive switching gain and included a method of estimating rotor speeds. Rotor speed estimation errors were presented as a first order simple function based on the difference between real stator currents and estimated stator currents. The Lyapunov stability theory was used to analyze the controller under different load disturbances and parameter uncertainties. Results of the study showed that the control signal of the scheme was smaller than signals obtained using traditional variable structure control schemes. It was concluded that speed tracking objectives can be obtained under various parameter and torque uncertainties. 9 refs., 7 figs.

  18. PLS-based memory control scheme for enhanced process monitoring

    KAUST Repository

    Harrou, Fouzi

    2017-01-20

    Fault detection is important for safe operation of various modern engineering systems. Partial least square (PLS) has been widely used in monitoring highly correlated process variables. Conventional PLS-based methods, nevertheless, often fail to detect incipient faults. In this paper, we develop new PLS-based monitoring chart, combining PLS with multivariate memory control chart, the multivariate exponentially weighted moving average (MEWMA) monitoring chart. The MEWMA are sensitive to incipient faults in the process mean, which significantly improves the performance of PLS methods and widen their applicability in practice. Using simulated distillation column data, we demonstrate that the proposed PLS-based MEWMA control chart is more effective in detecting incipient fault in the mean of the multivariate process variables, and outperform the conventional PLS-based monitoring charts.

  19. RFID - based Staff Control System (SCS) in Kazakhstan

    Science.gov (United States)

    Saparkhojayev, N.

    2015-06-01

    RFID - based Staff Control System (SCS) will allow complete hands-free access control, monitoring the whereabouts of employee and record the attendance of the employee as well. Moreover, with a help of this system, it is possible to have a nice report at the end of the month and based on the total number of worked hours, the salary will be allocated to each personnel. The access tag can be read up to 10 centimeters from the RFID reader. The proposed system is based on UHF RFID readers, supported with antennas at gate and transaction sections, and employee identification cards containing RFID-transponders which are able to electronically store information that can be read / written even without the physical contact with the help of radio medium. This system is an innovative system, which describes the benefits of applying RFID- technology in the Education System process of Republic of Kazakhstan. This paper presents the experiments conducted to set up RFID based SCS.

  20. Control of Yaw Disturbance Using Fuzzy Logic Based Yaw Stability Controller

    Directory of Open Access Journals (Sweden)

    S. Krishna

    2014-01-01

    Full Text Available Yaw stability is an important consideration for the vehicle directional stability and handling behavior during emergency maneuvers. In order to maintain the desired path of the vehicle, in presence of disturbances due to cross wind, different road conditions, and tire deflections, a fuzzy logic based yaw stability controller is proposed in this paper. Proposed control system receives yaw rate error, steering angle given by the driver, and side slip angle as inputs, for calculating the additional steering angle as output, for maintaining the yaw stability of the vehicle. As the side slip angle cannot be measured directly in a vehicle, it was estimated using a model based Kalman observer. A two-degrees-of-freedom vehicle model is considered in the present work. The effect of disturbance on yaw rate and yaw rate error of the vehicle is simulated for sinusoidal, step maneuver and compared with the existing fuzzy control system which uses two inputs such as steering angle and yaw rate. The simulation results show better performance of the proposed fuzzy based yaw controller as compared with existing control system. Proposed fuzzy based yaw stability controller can be implemented in steer-by-wire system for an active front steering of a road vehicle.