WorldWideScience

Sample records for bandwidth optoelectronic modulators

  1. Modulation bandwidth of a spin laser

    Science.gov (United States)

    Banerjee, D.; Adari, R.; Murthy, M.; Suggisetti, P.; Ganguly, S.; Saha, D.

    2011-04-01

    We have studied small signal frequency response of a spin laser. We have shown that the response is characterized by two distinct resonant peaks corresponding to the two polarization modes of the spin laser. It is observed that the modulation bandwidth of a spin laser can be smaller or larger than that of a conventional laser depending upon the current bias and spin relaxation time constant. A small value for spin relaxation constant may not be detrimental for modulation bandwidth. This anomalous observation is explained by considering both the amplitude and phase response of the two polarization modes. A spin laser can act as a combination of low-pass and bandpass filters. The passband frequency range is tunable by external bias. We have also studied the evolution of resonant peaks and modulation bandwidth as a function of spin relaxation time constant.

  2. Polybinary modulation for bandwidth limited optical links

    DEFF Research Database (Denmark)

    Vegas Olmos, Juan José; Jurado-Navas, Antonio

    2015-01-01

    Optical links using traditional modulation formats are reaching a plateau in terms of capacity, mainly due to bandwidth limitations in the devices employed at the transmitter and receivers. Advanced modulation formats, which boost the spectral efficiency, provide a smooth migration path towards...... effectively increase the available capacity. Advanced modulation formats however require digitalization of the signals and digital signal processing blocks to both generate and recover the data. There is therefore a trade-off in terms of efficiency gain vs. complexity. Poly binary modulation, a generalized...... form of partial response modulation, employs simple codification and filtering at the transmitter to drastically increase the spectral efficiency. At the receiver side, poly binary modulation requires low complexity direct detection and very little digital signal processing. This talk will review...

  3. Ultrafast broadband tunable-bandwidth magneto-optic modulator

    Science.gov (United States)

    Jones, Gavin D.; Elezzabi, Abdulhakem Y.

    1999-11-01

    We present our investigation of a variable bandwidth, ultrafast magneto-optic waveguide modulator employing the ferromagnetic resonant precession of the magnetization in a Bizmuth-substituted YIG film. Ultrafast magnetic field pulses, produced by current pulses propagated through a high-speed transmission line, are used to modulate the optical beam in the film. Such a device is capable of multi- gigahertz bandwidth and potential integration into current IC technology. Single frequency modulation of an 800 nm optical carrier is measured at bandwidths tuned between 4.6 and 11.7 GHz. The bandwidth is tuned by means of an externally applied DC magnetic field. It is found that the mode conversion efficiency of a waveguide type of device is limited by the linear birefringence of the thin Bi-YIG film. Birefringence-compensating schemes are discussed to optimize the mode conversion.

  4. Open-Loop Wide-Bandwidth Phase Modulation Techniques

    Directory of Open Access Journals (Sweden)

    Nitin Nidhi

    2011-01-01

    Full Text Available The ever-increasing growth in the bandwidth of wireless communication channels requires the transmitter to be wide-bandwidth and power-efficient. Polar and outphasing transmitter topologies are two promising candidates for such applications, in future. Both these architectures require a wide-bandwidth phase modulator. Open-loop phase modulation presents a viable solution for achieving wide-bandwidth operation. An overview of prior art and recent approaches for phase modulation is presented in this paper. Phase quantization noise cancellation was recently introduced to lower the out-of-band noise in a digital phase modulator. A detailed analysis on the impact of timing and quantization of the cancellation signal is presented. Noise generated by the transmitter in the receive band frequency poses another challenge for wide-bandwidth transmitter design. Addition of a noise transfer function notch, in a digital phase modulator, to reduce the noise in the receive band during phase modulation is described in this paper.

  5. Multi-Modulator for Bandwidth-Efficient Communication

    Science.gov (United States)

    Gray, Andrew; Lee, Dennis; Lay, Norman; Cheetham, Craig; Fong, Wai; Yeh, Pen-Shu; King, Robin; Ghuman, Parminder; Hoy, Scott; Fisher, Dave

    2009-01-01

    A modulator circuit board has recently been developed to be used in conjunction with a vector modulator to generate any of a large number of modulations for bandwidth-efficient radio transmission of digital data signals at rates than can exceed 100 Mb/s. The modulations include quadrature phaseshift keying (QPSK), offset quadrature phase-shift keying (OQPSK), Gaussian minimum-shift keying (GMSK), and octonary phase-shift keying (8PSK) with square-root raised-cosine pulse shaping. The figure is a greatly simplified block diagram showing the relationship between the modulator board and the rest of the transmitter. The role of the modulator board is to encode the incoming data stream and to shape the resulting pulses, which are fed as inputs to the vector modulator. The combination of encoding and pulse shaping in a given application is chosen to maximize the bandwidth efficiency. The modulator board includes gallium arsenide serial-to-parallel converters at its input end. A complementary metal oxide/semiconductor (CMOS) field-programmable gate array (FPGA) performs the coding and modulation computations and utilizes parallel processing in doing so. The results of the parallel computation are combined and converted to pulse waveforms by use of gallium arsenide parallel-to-serial converters integrated with digital-to-analog converters. Without changing the hardware, one can configure the modulator to produce any of the designed combinations of coding and modulation by loading the appropriate bit configuration file into the FPGA.

  6. Modulator reliability and bandwidth improvement: replacing tetrodes with MOSFETs

    International Nuclear Information System (INIS)

    Donaldson, A.R.

    1982-01-01

    Three types of power MOS field effect transistors were studied with the intent of replacing a parallel pair of vacuum tube tetrodes in a linear modulator. The tetrodes have the shortest lifetimes of any other tubes in the system. The FETs offer definite performance advantages when compared to bipolar transistors and definite cost advantages when compared to vacuum tubes. Replacement of the tetrodes does however require careful consideration of voltage, current and to a lesser extent bandwidth capability in order to enhance overall modulator reliability without compromising present performance

  7. Bandwidth tunable microwave photonic filter based on digital and analog modulation

    Science.gov (United States)

    Zhang, Qi; Zhang, Jie; Li, Qiang; Wang, Yubing; Sun, Xian; Dong, Wei; Zhang, Xindong

    2018-05-01

    A bandwidth tunable microwave photonic filter based on digital and analog modulation is proposed and experimentally demonstrated. The digital modulation is used to broaden the effective gain spectrum and the analog modulation is to get optical lines. By changing the symbol rate of data pattern, the bandwidth is tunable from 50 MHz to 700 MHz. The interval of optical lines is set according to the bandwidth of gain spectrum which is related to the symbol rate. Several times of bandwidth increase are achieved compared to a single analog modulation and the selectivity of the response is increased by 3.7 dB compared to a single digital modulation.

  8. Integrated graphene-based devices for optoelectronic applications

    DEFF Research Database (Denmark)

    Xiao, Sanshui

    Graphene opens up for novel optoelectronic applications thanks to its high carrier mobility, ultralarge absorption bandwidth, and extremely fast material response. Here I present novel integrated grapheneplasmonic waveguide modulator showing high modulation depth, thus giving a promising way...

  9. A wideband supply modulator for 20MHz RF bandwidth polar PAs in 65nm CMOS

    NARCIS (Netherlands)

    Shrestha, R.; van der Zee, Ronan A.R.; de Graauw, A.J.M.; Nauta, Bram

    2008-01-01

    Abstract A wideband modulator for a 20MHz bandwidth polar modulated PA is presented which achieves a maximum efficiency of 87.5% and a small signal -3dB bandwidth of 285MHz. Realized in 65nm CMOS, it consists of a cascoded nested Miller compensated linear amplifier and a class D switching amplifier.

  10. Ge-on-Si optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Liu Jifeng, E-mail: Jifeng.Liu@Dartmouth.edu [Thayer School of Engineering, Dartmouth College, Hanover, NH 03755 (United States); Camacho-Aguilera, Rodolfo; Bessette, Jonathan T.; Sun, Xiaochen [Microphotonics Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States); Wang Xiaoxin [Thayer School of Engineering, Dartmouth College, Hanover, NH 03755 (United States); Cai Yan; Kimerling, Lionel C.; Michel, Jurgen [Microphotonics Center, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States)

    2012-02-01

    Electronic-photonic synergy has become an increasingly clear solution to enhance the bandwidth and improve the energy efficiency of information systems. Monolithic integration of optoelectronic devices is the ideal solution for large-scale electronic-photonic synergy. Due to its pseudo-direct gap behavior in optoelectronic properties and compatibility with Si electronics, epitaxial Ge-on-Si has become an attractive solution for monolithic optoelectronics. In this paper we will review recent progress in Ge-on-Si optoelectronics, including photodetectors, electroabsorption modulators, and lasers. The performance of these devices has been enhanced by band-engineering such as tensile strain and n-type doping, which transforms Ge towards a direct gap material. Selective growth reduces defect density and facilitates monolithic integration at the same time. Ge-on-Si photodetectors have approached or exceeded the performance of their III-V counterparts, with bandwidth-efficiency product > 30 GHz for p-i-n photodiodes and bandwidth-gain product > 340 GHz for avalanche photodiodes. Enhanced Franz-Keldysh effect in tensile-strained Ge offers ultralow energy photonic modulation with < 30 fJ/bit energy consumption and > 100 GHz intrinsic bandwidth. Room temperature optically-pumped lasing as well as electroluminescence has also been achieved from the direct gap transition of band-engineered Ge-on-Si waveguides. These results indicate that band-engineered Ge-on-Si is promising to achieve monolithic active optoelectronic devices on a Si platform.

  11. High modulation bandwidth of a light-emitting diode with surface plasmon coupling (Conference Presentation)

    Science.gov (United States)

    Lin, Chun-Han; Tu, Charng-Gan; Yao, Yu-Feng; Chen, Sheng-Hung; Su, Chia-Ying; Chen, Hao-Tsung; Kiang, Yean-Woei; Yang, Chih-Chung

    2017-02-01

    Besides lighting, LEDs can be used for indoor data transmission. Therefore, a large modulation bandwidth becomes an important target in the development of visible LED. In this regard, enhancing the radiative recombination rate of carriers in the quantum wells of an LED is a useful method since the modulation bandwidth of an LED is related to the carrier decay rate besides the device RC time constant To increase the carrier decay rate in an LED without sacrificing its output power, the technique of surface plasmon (SP) coupling in an LED is useful. In this paper, the increases of modulation bandwidth by reducing mesa size, decreasing active layer thickness, and inducing SP coupling in blue- and green-emitting LEDs are illustrated. The results are demonstrated by comparing three different LED surface structures, including bare p-type surface, GaZnO current spreading layer, and Ag nanoparticles (NPs) for inducing SP coupling. In a single-quantum-well, blue-emitting LED with a circular mesa of 10 microns in radius, SP coupling results in a modulation bandwidth of 528.8 MHz, which is believed to be the record-high level. A smaller RC time constant can lead to a higher modulation bandwidth. However, when the RC time constant is smaller than 0.2 ns, its effect on modulation bandwidth saturates. The dependencies of modulation bandwidth on injected current density and carrier decay time confirm that the modulation bandwidth is essentially inversely proportional to a time constant, which is inversely proportional to the square-root of carrier decay rate and injected current density.

  12. Impact of modulation bandwidth on multiplexing using principal modes in MMF links.

    Science.gov (United States)

    Prasad, Rohan; Appaiah, Kumar

    2018-01-22

    Multimode fibers (MMFs) are widely used for short fiber links. However, the data rates through MMFs is limited owing to modal dispersion. The so-called "principal modes" (PMs) permit transmission and multiplexing through the MMFs without modal dispersion for small modulation bandwidths. For larger modulation bandwidths, however, they lose their dispersion-free nature. In this paper, we model the impact of modulation bandwidth and mode coupling strength on the performance of PMs. We develop a simulator that characterizes the dispersion and cross-talk of the PMs of few-mode and large-core graded-index MMFs with mode-dependent losses (MDL). Simulations reveal that for fibers without MDL, for modulation frequencies beyond 10 GHz diminishes the PMs' frequency response by more than 1 dB for 100 m in large-core MMF links and 10 km few-mode fiber links. With MDL, simulations reveal that for modulation bandwidths beyond 2 GHz diminishes the frequency response by 3 dB for a 1 km few-mode fiber and by more than 4 dB for a 1 km large-core multimode fiber. While multiplexing using PMs in large-core MMFs with MDL, we find that for modulation bandwidths beyond 3 GHz, the cross-talk is 20 dB in 1 km large-core MMF links, thereby limiting system performance.

  13. A Wideband Supply Modulator for 20MHz RF Bandwidth Polar PAs in 65nm CMOS

    NARCIS (Netherlands)

    Shrestha, R.; van der Zee, Ronan A.R.; de Graauw, Anton; Nauta, Bram

    2009-01-01

    Polar modulated RF amplifiers have the potential to enhance efficiency while achieving sufficient linearity for a signal having non-constant envelope. However, switching modulators used in such architectures to generate the envelope signal are difficult to implement because of the high bandwidth and

  14. Challenges in Polybinary Modulation for Bandwidth Limited Optical Links

    DEFF Research Database (Denmark)

    Vegas Olmos, Juan José; Tafur Monroy, Idelfonso; Madsen, Peter

    2016-01-01

    effectively increase the available capacity. Advanced modulation formats however require digitalization of the signals and digital signal processing blocks to both generate and recover the data. There is therefore a trade-off in terms of efficiency gain vs complexity. Polybinary modulation, a generalized form...

  15. Commercialization issues and funding opportunities for high-performance optoelectronic computing modules

    Science.gov (United States)

    Hessenbruch, John M.; Guilfoyle, Peter S.

    1997-01-01

    Low power, optoelectronic integrated circuits are being developed for high speed switching and data processing applications. These high performance optoelectronic computing modules consist of three primary components: vertical cavity surface emitting lasers, diffractive optical interconnect elements, and detector/amplifier/laser driver arrays. Following the design and fabrication of an HPOC module prototype, selected commercial funding sources will be evaluated to support a product development stage. These include the formation of a strategic alliance with one or more microprocessor or telecommunications vendors, and/or equity investment from one or more venture capital firms.

  16. Enhancement of the Modulation Bandwidth for surface Plasmon coupled LEDs for Visible Light Communication

    DEFF Research Database (Denmark)

    Li, Jiehui; Fadil, Ahmed; Ou, Haiyan

    2016-01-01

    The modulation bandwidth of surface plasmon coupled GaN-based LEDs is increased by ~1.2 times to 434.5 MHz compared with normal LED by applying Ag nanoparticles. These findings will help for the industrialization of VLC system....

  17. Improving the security of optoelectronic delayed feedback system by parameter modulation and system coupling

    Science.gov (United States)

    Liu, Lingfeng; Miao, Suoxia; Cheng, Mengfan; Gao, Xiaojing

    2016-02-01

    A coupled system with varying parameters is proposed to improve the security of optoelectronic delayed feedback system. This system is coupled by two parameter-varied optoelectronic delayed feedback systems with chaotic modulation. Dynamics performance results show that this system has a higher complexity compared to the original one. Furthermore, this system can conceal the time delay effectively against the autocorrelation function and delayed mutual information method and can increase the dimension space of secure parameters to resist brute-force attack by introducing the digital chaotic systems.

  18. Modulating the Optoelectronic Properties of Silver Nanowires Films: Effect of Capping Agent and Deposition Technique.

    Science.gov (United States)

    Lopez-Diaz, D; Merino, C; Velázquez, M M

    2015-11-11

    Silver nanowires 90 nm in diameter and 9 µm in length have been synthesized using different capping agents: polyvinyl pyrrolidone (PVP) and alkyl thiol of different chain lengths. The nanowire structure is not influenced by the displacement of PVP by alkyl thiols, although alkyl thiols modify the lateral aggregation of nanowires. We examined the effect of the capping agent and the deposition method on the optical and electrical properties of films prepared by Spray and the Langmuir-Schaefer methodologies. Our results revealed that nanowires capped with PVP and C8-thiol present the best optoelectronic properties. By using different deposition techniques and by modifying the nanowire surface density, we can modulate the optoelectronic properties of films. This strategy allows obtaining films with the optoelectronic properties required to manufacture touch screens and electromagnetic shielding.

  19. Modulating the Optoelectronic Properties of Silver Nanowires Films: Effect of Capping Agent and Deposition Technique

    Directory of Open Access Journals (Sweden)

    D. Lopez-Diaz

    2015-11-01

    Full Text Available Silver nanowires 90 nm in diameter and 9 µm in length have been synthesized using different capping agents: polyvinyl pyrrolidone (PVP and alkyl thiol of different chain lengths. The nanowire structure is not influenced by the displacement of PVP by alkyl thiols, although alkyl thiols modify the lateral aggregation of nanowires. We examined the effect of the capping agent and the deposition method on the optical and electrical properties of films prepared by Spray and the Langmuir-Schaefer methodologies. Our results revealed that nanowires capped with PVP and C8-thiol present the best optoelectronic properties. By using different deposition techniques and by modifying the nanowire surface density, we can modulate the optoelectronic properties of films. This strategy allows obtaining films with the optoelectronic properties required to manufacture touch screens and electromagnetic shielding.

  20. Structured Low-Density Parity-Check Codes with Bandwidth Efficient Modulation

    Science.gov (United States)

    Cheng, Michael K.; Divsalar, Dariush; Duy, Stephanie

    2009-01-01

    In this work, we study the performance of structured Low-Density Parity-Check (LDPC) Codes together with bandwidth efficient modulations. We consider protograph-based LDPC codes that facilitate high-speed hardware implementations and have minimum distances that grow linearly with block sizes. We cover various higher- order modulations such as 8-PSK, 16-APSK, and 16-QAM. During demodulation, a demapper transforms the received in-phase and quadrature samples into reliability information that feeds the binary LDPC decoder. We will compare various low-complexity demappers and provide simulation results for assorted coded-modulation combinations on the additive white Gaussian noise and independent Rayleigh fading channels.

  1. High-speed 405-nm superluminescent diode (SLD) with 807-MHz modulation bandwidth

    KAUST Repository

    Shen, Chao

    2016-08-25

    III-nitride LEDs are fundamental components for visible-light communication (VLC). However, the modulation bandwidth is inherently limited by the relatively long carrier lifetime. In this letter, we present the 405 nm emitting superluminescent diode (SLD) with tilted facet design on semipolar GaN substrate, showing a broad emission of ∼9 nm at 20 mW optical power. Owing to the fast recombination (τ<0.35 ns) through the amplified spontaneous emission, the SLD exhibits a significantly large 3-dB bandwidth of 807 MHz. A data rate of 1.3 Gbps with a bit-error rate of 2.9 × 10 was obtained using on-off keying modulation scheme, suggesting the SLD being a high-speed transmitter for VLC applications.

  2. Potential Upgrade of the CMS Tracker Analog Readout Optical Links Using Bandwidth Efficient Digital Modulation

    OpenAIRE

    Dris, Stefanos; Foudas, Costas; Gill, Karl; Grabit, Robert; Ricci, Daniel; Troska, Jan; Vasey, Francois

    2010-01-01

    The potential application of advanced digital communication schemes in a future upgrade of the CMS Tracker readout optical links is currently being investigated at CERN. We show experimentally that multi-Gbit/s data rates are possible over the current 40 MSamples/s analog optical links by employing techniques similar to those used in ADSL. The concept involves using one or more digitally-modulated sinusoidal carriers in order to make efficient use of the available bandwidth.

  3. Potential Upgrade of the CMS Tracker Analog Readout Optical Links using Bandwidth Efficient Digital Modulation

    CERN Document Server

    Dris, Stefanos; Gill, K; Grabit, R; Ricci, D; Troska, J; Vasey, F

    2007-01-01

    The potential application of advanced digital communication schemes in a future upgrade of the CMS Tracker readout optical links is currently being investigated at CERN. We show experimentally that multi-Gbit/s data rates are possible over the current 40 MSamples/s analog optical links by employing techniques similar to those used in ADSL. The concept involves using one or more digitally-modulated sinusoidal carriers in order to make efficient use of the available bandwidth.

  4. All-optical characterization of large-signal modulation bandwidth of a monolithically integrated DFB-EA

    DEFF Research Database (Denmark)

    Blaaberg, Søren; Mulvad, Hans Christian Hansen; Oxenløwe, Leif Katsuo

    2009-01-01

    We use an all-optical method to characterize the modulation bandwidth of a DFB-EA designed for 100 Gb/s Ethernet. In a large-signal wavelength conversion set-up, we show the device has an all-optical bandwidth of 83 GHz....

  5. CARBON-FIBRE-REINFORCED POLYMER PARTS EFFECT ON SPACECRAFT OPTOELECTRONIC MODULE LENS SCATTERING

    Directory of Open Access Journals (Sweden)

    S. S. Kolasha

    2016-01-01

    Full Text Available Spacecraft optoelectronic modules traditionally have aluminum alloy or titanium alloy casing which substantial weight increases fuel consumption required to put them into orbit and, consequently, total cost of the project. Carbon fiber reinforced polymer based composite constructive materials is an efficient solution that allows reducing weight and dimensions of large optoelectronic modules 1,5–3 times and the coefficient of linear thermal expansion 15–20 times if compared with metals. Optical characteristic is a crucial feature of carbon-fibre-reinforced polymer that determines composite material interaction with electromagnetic emission within the optical range. This work was intended to develop a method to evaluate Carbon fiber reinforced polymer optoelectronic modules casing effect on lens scattering by computer simulation with Zemax application software package. Degrees of scattered, reflected and absorbed radiant flux effect on imaging quality are described here. The work included experimental study in order to determine bidirectional reflectance distribution function by goniometric method for LUP-0.1 carbon fabric check test pieces of EDT-69U epoxy binder with EPOFLEX-0.4 glue layer and 5056-3.5-23-A aluminium honeycomb filler. The scattered emission was registered within a hemisphere above the check test piece surface. Optical detection direction was determined with zenith (0º < θ < 90º and azimuth (0º < φ < 180º angles with 10° increment. The check test piece surface was proved to scatter emission within a narrow angle range (approximately 20° with clear directivity. Carbon fiber reinforced polymers was found to feature integrated reflectance coefficient 3 to 4 times greater than special coatings do. 

  6. Field Effect Optoelectronic Modulation of Quantum-Confined Carriers in Black Phosphorus.

    Science.gov (United States)

    Whitney, William S; Sherrott, Michelle C; Jariwala, Deep; Lin, Wei-Hsiang; Bechtel, Hans A; Rossman, George R; Atwater, Harry A

    2017-01-11

    We report measurements of the infrared optical response of thin black phosphorus under field-effect modulation. We interpret the observed spectral changes as a combination of an ambipolar Burstein-Moss (BM) shift of the absorption edge due to band-filling under gate control, and a quantum confined Franz-Keldysh (QCFK) effect, phenomena that have been proposed theoretically to occur for black phosphorus under an applied electric field. Distinct optical responses are observed depending on the flake thickness and starting carrier concentration. Transmission extinction modulation amplitudes of more than two percent are observed, suggesting the potential for use of black phosphorus as an active material in mid-infrared optoelectronic modulator applications.

  7. A control unit for a laser module of optoelectronic computing environment with dynamic architecture

    Directory of Open Access Journals (Sweden)

    Lipinskii A. Y.

    2013-06-01

    Full Text Available The paper presents the developed control unit of laser modules of optoelectronic acousto-optic computing environment. The unit is based on ARM micro¬con¬troller of Cortex M3 family, and allows alternating between recording (erase and reading modes in accordance with a predetermined algorithm and settings — exposure time and intensity. The principal electric circuit of the presented device, the block diagram of microcontroller algorithm, and the example application of the developed control unit in the layout of the experimental setup are provided.

  8. Impact of crystal orientation on the modulation bandwidth of InGaN/GaN light-emitting diodes

    Science.gov (United States)

    Monavarian, M.; Rashidi, A.; Aragon, A. A.; Oh, S. H.; Rishinaramangalam, A. K.; DenBaars, S. P.; Feezell, D.

    2018-01-01

    High-speed InGaN/GaN blue light-emitting diodes (LEDs) are needed for future gigabit-per-second visible-light communication systems. Large LED modulation bandwidths are typically achieved at high current densities, with reports close to 1 GHz bandwidth at current densities ranging from 5 to 10 kA/cm2. However, the internal quantum efficiency (IQE) of InGaN/GaN LEDs is quite low at high current densities due to the well-known efficiency droop phenomenon. Here, we show experimentally that nonpolar and semipolar orientations of GaN enable higher modulation bandwidths at low current densities where the IQE is expected to be higher and power dissipation is lower. We experimentally compare the modulation bandwidth vs. current density for LEDs on nonpolar (10 1 ¯ 0 ), semipolar (20 2 ¯ 1 ¯) , and polar (" separators="|0001 ) orientations. In agreement with wavefunction overlap considerations, the experimental results indicate a higher modulation bandwidth for the nonpolar and semipolar LEDs, especially at relatively low current densities. At 500 A/cm2, the nonpolar LED has a 3 dB bandwidth of ˜1 GHz, while the semipolar and polar LEDs exhibit bandwidths of 260 MHz and 75 MHz, respectively. A lower carrier density for a given current density is extracted from the RF measurements for the nonpolar and semipolar LEDs, consistent with the higher wavefunction overlaps in these orientations. At large current densities, the bandwidth of the polar LED approaches that of the nonpolar and semipolar LEDs due to coulomb screening of the polarization field. The results support using nonpolar and semipolar orientations to achieve high-speed LEDs at low current densities.

  9. Performance Evaluation of a High Bandwidth Liquid Fuel Modulation Valve for Active Combustion Control

    Science.gov (United States)

    Saus, Joseph R.; DeLaat, John C.; Chang, Clarence T.; Vrnak, Daniel R.

    2012-01-01

    At the NASA Glenn Research Center, a characterization rig was designed and constructed for the purpose of evaluating high bandwidth liquid fuel modulation devices to determine their suitability for active combustion control research. Incorporated into the rig s design are features that approximate conditions similar to those that would be encountered by a candidate device if it were installed on an actual combustion research rig. The characterized dynamic performance measures obtained through testing in the rig are planned to be accurate indicators of expected performance in an actual combustion testing environment. To evaluate how well the characterization rig predicts fuel modulator dynamic performance, characterization rig data was compared with performance data for a fuel modulator candidate when the candidate was in operation during combustion testing. Specifically, the nominal and off-nominal performance data for a magnetostrictive-actuated proportional fuel modulation valve is described. Valve performance data were collected with the characterization rig configured to emulate two different combustion rig fuel feed systems. Fuel mass flows and pressures, fuel feed line lengths, and fuel injector orifice size was approximated in the characterization rig. Valve performance data were also collected with the valve modulating the fuel into the two combustor rigs. Comparison of the predicted and actual valve performance data show that when the valve is operated near its design condition the characterization rig can appropriately predict the installed performance of the valve. Improvements to the characterization rig and accompanying modeling activities are underway to more accurately predict performance, especially for the devices under development to modulate fuel into the much smaller fuel injectors anticipated in future lean-burning low-emissions aircraft engine combustors.

  10. Digital modulation schemes for high speed transmission through low bandwidth lowpass analog links

    Science.gov (United States)

    Andrawis, Alfred S.; Flippin, Quentin J.

    1995-01-01

    Existing NTSC (National Television System Committee) standard will be phased out and replaced with HDTV (High Definition Television) standard within the next 10 years. Accordingly, the existing video network system operated by NASA will become obsolete and requires either replacement or modification to accommodate digital transmission. Network replacement is extremely expensive, hence, several digital modulation schemes are investigated in this report to accomplish digital transmission over existing analog links saving NASA from the cost of network replacement. There are two competing transmission systems available for HDTV transmission over limited bandwidth channels. The cost and performance of the two competing schemes are remarkably similar. However, the input data rate in such a case is limited to 40 Mbit/s. Transmission of higher data rates is possible using simple signal processing techniques. On the other hand, a third transmission system, multilevel pulse amplitude modulation (M-PAM) is proposed. M-PAM is the first stage of the well known M-VSB. This M-PAM scheme is much simpler and uses the channel more efficiently. The three schemes are compared and preliminary conclusions were made. Despite of several similarities, each modulation scheme has it unique merits. To determine the suitability of each scheme, more investigations and laboratory tests for all schemes are needed.

  11. Performance evaluation of multilevel modulation formats using partial response for capacity upgrade in access network with limited electronic bandwidth

    DEFF Research Database (Denmark)

    Madsen, Peter; Suhr, Lau Frejstrup; Rodríguez Páez, Juan Sebastián

    2016-01-01

    We present a successful experimental evaluation of 4 level Pulse Amplitude Modulation (4-PAM) and Duobinary modulation. An experimental performance evaluation is presented for Duobinary 4 PAM and other modulation formats. All modulation formants used, may be considered to be implemented in future...... Passive Optical Network (PON) class access networks with limited electrical bandwidth. We compared NRZ, Duobinary, 4-PAM and Duobinary 4-PAM operating at 9 Gbaud over 20 km single mode fiber. The results provides an insight and guidelines on the utilization of these advanced modulation formats....

  12. Modulated method for efficient, narrow-bandwidth, laser Compton X-ray and gamma-ray sources

    Science.gov (United States)

    Barty, Christopher P. J.

    2017-07-11

    A method of x-ray and gamma-ray generation via laser Compton scattering uses the interaction of a specially-formatted, highly modulated, long duration, laser pulse with a high-frequency train of high-brightness electron bunches to both create narrow bandwidth x-ray and gamma-ray sources and significantly increase the laser to Compton photon conversion efficiency.

  13. Linearly chirped waveform generation with large time-bandwidth product using sweeping laser and dual-polarization modulator

    Science.gov (United States)

    Li, Xuan; Zhao, Shanghong; Li, Yongjun; Zhu, Zihang; Qu, Kun; Li, Tao; Hu, Dapeng

    2018-03-01

    A method for photonic generation of a linearly chirped microwave waveform using a frequency-sweeping laser and a dual-polarization modulator is proposed and investigated. A frequency-sweeping continuous-wave light is generated from the laser and then sent to the modulator. In the modulator, one part of the light is modulated with an RF signal to generate a frequency-shifting optical signal, while another part of the light is passed through a polarization rotator to rotate the polarization to an orthogonal direction. At the output of the modulator, the two optical signals are combined with orthogonal polarizations, and then injected into a polarization delay device to introduce a time delay. After combining the two optical signals for heterodyning, a linearly chirped waveform can be generated. The bandwidth, time duration, chirp rate and sign, central frequency of the generated waveform can be tuned independently and flexibly, furthermore, frequency doubling for the central frequency can be achieved in the waveform generation. A simulation is demonstrated to verify the proposed scheme, a linearly chirped microwave pulse with up or down chirp, central frequency of 20 or 40 GHz, bandwidth of 20 GHz, time duration of 500 ns, time-bandwidth product (TBWP) of 10000 is obtained.

  14. Bandwidth and repetition rate programmable Nyquist sinc-shaped pulse train source based on intensity modulators and four-wave mixing.

    Science.gov (United States)

    Cordette, S; Vedadi, A; Shoaie, M A; Brès, C-S

    2014-12-01

    We propose and experimentally demonstrate an all-optical Nyquist sinc-shaped pulse train source based on intensity modulation and four-wave mixing. The proposed scheme allows for the tunability of the bandwidth and the full flexibility of the repetition rate in the limit of the electronic bandwidth of the modulators used through the flexible synthesis of rectangular frequency combs. Bandwidth up to 360 GHz at 40 GHz rate and up to 45 frequency lines at 5 GHz rate are demonstrated with 40 GHz modulators.

  15. Effect of modulation frequency bandwidth on measurement accuracy and precision for digital diffuse optical spectroscopy (dDOS)

    Science.gov (United States)

    Jung, Justin; Istfan, Raeef; Roblyer, Darren

    2014-03-01

    Near-infrared (NIR) frequency-domain Diffuse Optical Spectroscopy (DOS) is an emerging technology with a growing number of potential clinical applications. In an effort to reduce DOS system complexity and improve portability, we recently demonstrated a direct digital sampling method that utilizes digital signal generation and detection as a replacement for more traditional analog methods. In our technique, a fast analog-to-digital converter (ADC) samples the detected time-domain radio frequency (RF) waveforms at each modulation frequency in a broad-bandwidth sweep (50- 300MHz). While we have shown this method provides comparable results to other DOS technologies, the process is data intensive as digital samples must be stored and processed for each modulation frequency and wavelength. We explore here the effect of reducing the modulation frequency bandwidth on the accuracy and precision of extracted optical properties. To accomplish this, the performance of the digital DOS (dDOS) system was compared to a gold standard network analyzer based DOS system. With a starting frequency of 50MHz, the input signal of the dDOS system was swept to 100, 150, 250, or 300MHz in 4MHz increments and results were compared to full 50-300MHz networkanalyzer DOS measurements. The average errors in extracted μa and μs' with dDOS were lowest for the full 50-300MHz sweep (less than 3%) and were within 3.8% for frequency bandwidths as narrow as 50-150MHz. The errors increased to as much as 9.0% when a bandwidth of 50-100MHz was tested. These results demonstrate the possibility for reduced data collection with dDOS without critical compensation of optical property extraction.

  16. Extended-bandwidth frequency sweeps of a distributed feedback laser using combined injection current and temperature modulation

    Science.gov (United States)

    Hefferman, Gerald; Chen, Zhen; Wei, Tao

    2017-07-01

    This article details the generation of an extended-bandwidth frequency sweep using a single, communication grade distributed feedback (DFB) laser. The frequency sweep is generated using a two-step technique. In the first step, injection current modulation is employed as a means of varying the output frequency of a DFB laser over a bandwidth of 99.26 GHz. A digital optical phase lock loop is used to lock the frequency sweep speed during current modulation, resulting in a linear frequency chirp. In the second step, the temperature of the DFB laser is modulated, resulting in a shifted starting laser output frequency. A laser frequency chirp is again generated beginning at this shifted starting frequency, resulting in a frequency-shifted spectrum relative to the first recorded data. This process is then repeated across a range of starting temperatures, resulting in a series of partially overlapping, frequency-shifted spectra. These spectra are then aligned using cross-correlation and combined using averaging to form a single, broadband spectrum with a total bandwidth of 510.9 GHz. In order to investigate the utility of this technique, experimental testing was performed in which the approach was used as the swept-frequency source of a coherent optical frequency domain reflectometry system. This system was used to interrogate an optical fiber containing a 20 point, 1-mm pitch length fiber Bragg grating, corresponding to a period of 100 GHz. Using this technique, both the periodicity of the grating in the frequency domain and the individual reflector elements of the structure in the time domain were resolved, demonstrating the technique's potential as a method of extending the sweeping bandwidth of semiconductor lasers for frequency-based sensing applications.

  17. Optoelectronic Infrastructure for Radio Frequency and Optical Phased Arrays

    Science.gov (United States)

    Cai, Jianhong

    2015-01-01

    Optoelectronic integrated circuits offer radiation-hardened solutions for satellite systems in addition to improved size, weight, power, and bandwidth characteristics. ODIS, Inc., has developed optoelectronic integrated circuit technology for sensing and data transfer in phased arrays. The technology applies integrated components (lasers, amplifiers, modulators, detectors, and optical waveguide switches) to a radio frequency (RF) array with true time delay for beamsteering. Optical beamsteering is achieved by controlling the current in a two-dimensional (2D) array. In this project, ODIS integrated key components to produce common RF-optical aperture operation.

  18. Perspectives in optoelectronics

    National Research Council Canada - National Science Library

    Jha, Sudhanshu S

    1995-01-01

    ..., optoelectronics is playing a major role in both applied as well as basic sciences. In years to come, i t is destined to change the face of information technology and robotics, involving optical sensing and control, information storage, signal and image processing, communications, and computing. Because of the possibility of using large bandwidths availa...

  19. Efficient generation of a narrow-bandwidth and frequency-modulated beam pair from Yb atoms in a ladder configuration

    International Nuclear Information System (INIS)

    Song, Minsoo; Yoon, Tai Hyun

    2011-01-01

    We report on the generation of narrow-bandwidth and frequency-modulated cascaded emission of two photons from a collimated Yb atomic beam. Efficient population transfer from the ground state (6s 2 1 S 0 ) to upper state (6s7s 1 S 0 ), of which direct transition at 291.1 nm is dipole forbidden, is achieved through a resonant two-photon excitation enhanced by the electromagnetically induced transparency mediated by the intermediate state (6s6p 1 P 1 ). Then cascaded emission of two photons with a bandwidth of 54 MHz at 611.3 nm (idler) and 555.8 nm (signal) occurs in sequence from the upper state via the spin triplet state (6s 2 3 P 1 ). Numerical calculations of the density matrix equations taking into account the residual Doppler effect and strong driving fields successfully explain the experimental results for the idler and signal beam intensities depending on the various parameters of the driving fields. Synchronized optical switching and frequency-modulation characteristics of the idler and signal beams are also reported.

  20. High-bandwidth generation of duobinary and alternate-mark-inversion modulation formats using SOA-based signal processing.

    Science.gov (United States)

    Dailey, James M; Power, Mark J; Webb, Roderick P; Manning, Robert J

    2011-12-19

    We report on the novel all-optical generation of duobinary (DB) and alternate-mark-inversion (AMI) modulation formats at 42.6 Gb/s from an input on-off keyed signal. The modulation converter consists of two semiconductor optical amplifier (SOA)-based Mach-Zehnder interferometer gates. A detailed SOA model numerically confirms the operational principles and experimental data shows successful AMI and DB conversion at 42.6 Gb/s. We also predict that the operational bandwidth can be extended beyond 40 Gb/s by utilizing a new pattern-effect suppression scheme, and demonstrate dramatic reductions in patterning up to 160 Gb/s. We show an increasing trade-off between pattern-effect reduction and mean output power with increasing bitrate.

  1. On Bandwidth Efficient Modulation for High-Data-Rate Wireless LAN Systems

    Directory of Open Access Journals (Sweden)

    Stolpman Victor

    2002-01-01

    Full Text Available We address the problem of high-data-rate orthogonal frequency division multiplexed (OFDM systems under restrictive bandwidth constraints. Based on recent theoretic results, multiple-input multiple-output (MIMO configurations are best suited for this problem. In this paper, we examine several MIMO configurations suitable for high rate transmission. In all scenarios considered, perfect channel state information (CSI is assumed at the receiver. In constrast, availability of CSI at the transmitter is addressed separately. We show that powerful space-time codes can be developed by combining some simple well-known techniques. In fact, we show that for certain configurations, these space-time MIMO configurations are near optimum in terms of outage capacity as compared to previously published codes. Performance evaluation of these techniques is demonstrated within the IEEE 802.11a framework via Monte Carlo simulations.

  2. Effective information rates of single-carrier and multi-carrier modulation schemes for bandwidth constrained IM/DD systems

    KAUST Repository

    Mazahir, Sana

    2017-07-31

    Information-theoretic and signal processing aspects of some modulation schemes designed for intensity modulation/direct detection (IM/DD) optical wireless communication (OWC) systems are studied. Due to the constraints of IM/DD signals (non-negative real and baseband signals), the construction of these signals along with their time and frequency characteristics differ from their RF counterparts. This necessitates a careful study of such schemes under practical constraints. Three schemes are studied in this paper, namely, single carrier pulse amplitude modulation (SC-PAM), asymmetrically clipped optical OFDM (ACO-OFDM), and DC biased optical OFDM (DCO-OFDM). Our aim is to carry out a comparative study of these schemes in the presence of identical constraints on bandwidth and average optical power. The study reveals that the clipping operation required in ACO-OFDM significantly reduces its information rate, and as a result, it is outperformed by SC-PAM. Such a limitation does not apply to DCO-OFDM which has a higher information rate, even though part of the available optical power is expended in the non-information-bearing DC bias.

  3. A 10 MHz Bandwidth Continuous-Time Delta-Sigma Modulator for Portable Ultrasound Scanners

    DEFF Research Database (Denmark)

    Llimos Muntal, Pere; Jørgensen, Ivan Harald Holger; Bruun, Erik

    2016-01-01

    A fourth-order 1-bit continuous-time delta-sigma modulator designed in a 65 nm process for portable ultrasound scanners is presented in this paper. The loop filter consists of RCintegrators, with programmable capacitor arrays and resistors, and the quantizer is implemented with a high-speed clocked...

  4. Enhanced direct-modulated bandwidth of 37 GHz by a multi-section laser with a coupled-cavity-injection-grating design

    DEFF Research Database (Denmark)

    Bach, L.; Kaiser, W.; Reithmaier, J.P.

    2003-01-01

    Using a new multi-section laser concept based on a coupled-cavity-injection-grating design, the material related intrinsic 3 dB modulation bandwidth can be enhanced up to 37 GHz for a 1.5 mm long device.......Using a new multi-section laser concept based on a coupled-cavity-injection-grating design, the material related intrinsic 3 dB modulation bandwidth can be enhanced up to 37 GHz for a 1.5 mm long device....

  5. High bandwidth pixel detector modules for the ATLAS Insertable B-Layer

    International Nuclear Information System (INIS)

    Backhaus, Malte

    2014-01-01

    The investigation of the nature of the recently discovered electro-weak symmetry breaking mechanism of the standard model of particle physics as well as the search for physics beyond the standard model with the LHC require to collect even more data. To achieve this goal, the luminosity of the LHC will be increased in two steps. The increased luminosity results in serious challenges for the inner tracking systems of the experiments at the LHC. The ATLAS pixel detector will also be upgraded in a two stage program. During the shutdown in 2013 and 2014 a fourth hybrid pixel detector layer, the socalled Insertable B-Layer (IBL) is inserted inside the existing pixel detector. This thesis focuses on the characterization, performance measurement, and production quality assurance of the central sensitive elements of the IBL, the modules. This includes a full characterization of the readout chip (FE-I4) and of the assembled modules. A completely new inner tracking system is mandatory in ATLAS after the second luminosity increase in the shutdown of 2022 and 2023. The final chapter of this thesis introduces a new module concept that uses an industrial high voltage CMOS technology as sensor layer, which is capacitively coupled to the FE-I4 readout chip.

  6. Defect-Based Modulation of Optoelectronic Properties for Biofunctionalized Hexagonal Boron Nitride Nanosheets.

    Science.gov (United States)

    Shakourian-Fard, Mehdi; Heydari, Hadiseh; Kamath, Ganesh

    2017-09-06

    Defect engineering potentially allows for dramatic tuning of the optoelectronic properties of two-dimensional materials. With the help of DFT calculations, a systematic study of DNA nucleobases adsorbed on hexagonal boron-nitride nanoflakes (h-BNNFs) with boron (V B ) and nitrogen (V N ) monovacancies is presented. The presence of V N and V B defects increases the binding strength of nucleobases by 9 and 34 kcal mol -1 , respectively (h-BNNF-V B >h-BNNF-V N >h-BNNF). A more negative electrostatic potential at the V B site makes the h-BNNF-V B surface more reactive than that of h-BNNF-V N , enabling H-bonding interactions with nucleobases. This binding energy difference affects the recovery time-a significant factor for developing DNA biosensors-of the surfaces in the order h-BNNF-V B >h-BNNF-V N >h-BNNF. The presence of V B and V N defect sites increases the electrical conductivity of the h-BNNF surface, V N defects being more favorable than V B sites. The blueshift of absorption peaks of the h-BNNF-V B -nucleobase complexes, in contrast to the redshift observed for h-BNNF-V N -nucleobase complexes, is attributed to their observed differences in binding energies, the HOMO-LUMO energy gap and other optoelectronic properties. Time-dependent DFT calculations reveal that the monovacant boron-nitride-sheet-nucleobase composites absorb visible light in the range 300-800 nm, thus making them suitable for light-emitting devices and sensing nucleobases in the visible region. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Re-use of Low Bandwidth Equipment for High Bit Rate Transmission Using Signal Slicing Technique

    DEFF Research Database (Denmark)

    Wagner, Christoph; Spolitis, S.; Vegas Olmos, Juan José

    : Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates.......: Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates....

  8. Organic optoelectronics

    CERN Document Server

    Hu, Wenping; Gong, Xiong; Zhan, Xiaowei; Fu, Hongbing; Bjornholm, Thomas

    2012-01-01

    Written by internationally recognized experts in the field with academic as well as industrial experience, this book concisely yet systematically covers all aspects of the topic.The monograph focuses on the optoelectronic behavior of organic solids and their application in new optoelectronic devices. It covers organic electroluminescent materials and devices, organic photonics, materials and devices, as well as organic solids in photo absorption and energy conversion. Much emphasis is laid on the preparation of functional materials and the fabrication of devices, from materials synthesis a

  9. High efficiency optoelectronic terahertz sources

    Science.gov (United States)

    Lampin, Jean-François; Peytavit, Emilien; Akalin, Tahsin; Ducournau, G.; Hindle, Francis; Mouret, Gael

    2010-08-01

    We have developed a new generation of optoelectronic large bandwidth terahertz sources based on TEM horn antennas monolithically integrated with several types of photodetectors: low-temperature grown GaAs (LTG-GaAs) planar photoconductors, vertically integrated LTG-GaAs photoconductors on silicon substrate and uni-travelling-carrier photodiodes. Results of pulsed (time-domain) and photomixing (CW, frequency domain) experiments are presented.

  10. Comparing auditory filter bandwidths, spectral ripple modulation detection, spectral ripple discrimination, and speech recognition: Normal and impaired hearinga)

    Science.gov (United States)

    Davies-Venn, Evelyn; Nelson, Peggy; Souza, Pamela

    2015-01-01

    Some listeners with hearing loss show poor speech recognition scores in spite of using amplification that optimizes audibility. Beyond audibility, studies have suggested that suprathreshold abilities such as spectral and temporal processing may explain differences in amplified speech recognition scores. A variety of different methods has been used to measure spectral processing. However, the relationship between spectral processing and speech recognition is still inconclusive. This study evaluated the relationship between spectral processing and speech recognition in listeners with normal hearing and with hearing loss. Narrowband spectral resolution was assessed using auditory filter bandwidths estimated from simultaneous notched-noise masking. Broadband spectral processing was measured using the spectral ripple discrimination (SRD) task and the spectral ripple depth detection (SMD) task. Three different measures were used to assess unamplified and amplified speech recognition in quiet and noise. Stepwise multiple linear regression revealed that SMD at 2.0 cycles per octave (cpo) significantly predicted speech scores for amplified and unamplified speech in quiet and noise. Commonality analyses revealed that SMD at 2.0 cpo combined with SRD and equivalent rectangular bandwidth measures to explain most of the variance captured by the regression model. Results suggest that SMD and SRD may be promising clinical tools for diagnostic evaluation and predicting amplification outcomes. PMID:26233047

  11. Comparing auditory filter bandwidths, spectral ripple modulation detection, spectral ripple discrimination, and speech recognition: Normal and impaired hearing.

    Science.gov (United States)

    Davies-Venn, Evelyn; Nelson, Peggy; Souza, Pamela

    2015-07-01

    Some listeners with hearing loss show poor speech recognition scores in spite of using amplification that optimizes audibility. Beyond audibility, studies have suggested that suprathreshold abilities such as spectral and temporal processing may explain differences in amplified speech recognition scores. A variety of different methods has been used to measure spectral processing. However, the relationship between spectral processing and speech recognition is still inconclusive. This study evaluated the relationship between spectral processing and speech recognition in listeners with normal hearing and with hearing loss. Narrowband spectral resolution was assessed using auditory filter bandwidths estimated from simultaneous notched-noise masking. Broadband spectral processing was measured using the spectral ripple discrimination (SRD) task and the spectral ripple depth detection (SMD) task. Three different measures were used to assess unamplified and amplified speech recognition in quiet and noise. Stepwise multiple linear regression revealed that SMD at 2.0 cycles per octave (cpo) significantly predicted speech scores for amplified and unamplified speech in quiet and noise. Commonality analyses revealed that SMD at 2.0 cpo combined with SRD and equivalent rectangular bandwidth measures to explain most of the variance captured by the regression model. Results suggest that SMD and SRD may be promising clinical tools for diagnostic evaluation and predicting amplification outcomes.

  12. Optoelectronic Infrastructure for RF/Optical Phased Arrays Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Optoelectronic integrated circuits offer radiation-hard solutions for satellite systems with much improved SWPB (size, weight, power and bandwidth). The phased array...

  13. Nanowire Optoelectronics

    OpenAIRE

    Wang Zhihuan; Nabet Bahram

    2015-01-01

    Semiconductor nanowires have been used in a variety of passive and active optoelectronic devices including waveguides, photodetectors, solar cells, light-emitting diodes (LEDs), lasers, sensors, and optical antennas. We review the optical properties of these nanowires in terms of absorption, guiding, and radiation of light, which may be termed light management. Analysis of the interaction of light with long cylindrical/hexagonal structures with ...

  14. A High Modulation Bandwidth, 110 GHz Power DAC Cell forIQ Transmitter Arrays With Direct Amplitude and PhaseModulation

    Science.gov (United States)

    2014-06-23

    transmission line. Some parasitic capacitance and parasitic inductance asymmetry is inherent to the layout of the Gilbert cell due to the metal crossing at the...design imperfections and differential circuit layout inductive and capacitive parasitic asymmetries. An array element output power ON/OFF ratio better...has traditionallybeen used for automotive and military radar applica- tions. In recent years, the ever-increasing bandwidth needs of users streaming

  15. Ultrahigh bandwidth signal processing

    DEFF Research Database (Denmark)

    Oxenløwe, Leif Katsuo

    2016-01-01

    Optical time lenses have proven to be very versatile for advanced optical signal processing. Based on a controlled interplay between dispersion and phase-modulation by e.g. four-wave mixing, the processing is phase-preserving, an hence useful for all types of data signals including coherent multi......-level modulation founats. This has enabled processing of phase-modulated spectrally efficient data signals, such as orthogonal frequency division multiplexed (OFDM) signa In that case, a spectral telescope system was used, using two time lenses with different focal lengths (chirp rates), yielding a spectral...... regeneratio These operations require a broad bandwidth nonlinear platform, and novel photonic integrated nonlinear platform like aluminum gallium arsenide nano-waveguides used for 1.28 Tbaud optical signal processing will be described....

  16. Modulation of intrinsic and reflexive contributions to low-back stabilization due to vision, task instruction, and perturbation bandwidth

    NARCIS (Netherlands)

    van Drunen, P.; Koumans, Y.; van der Helm, F.C.T.; van Dieen, J.H.; Happee, R.

    2015-01-01

    The goal of this study is to assess how reflexes and intrinsic properties contribute to low-back stabilization and modulate with conditions. Upper body sway was evoked by anterior–posterior platform translations, while subjects were seated with a restrained pelvis and free upper body. Kinematic

  17. Nanowire Optoelectronics

    Directory of Open Access Journals (Sweden)

    Wang Zhihuan

    2015-12-01

    Full Text Available Semiconductor nanowires have been used in a variety of passive and active optoelectronic devices including waveguides, photodetectors, solar cells, light-emitting diodes (LEDs, lasers, sensors, and optical antennas. We review the optical properties of these nanowires in terms of absorption, guiding, and radiation of light, which may be termed light management. Analysis of the interaction of light with long cylindrical/hexagonal structures with subwavelength diameters identifies radial resonant modes, such as Leaky Mode Resonances, or Whispering Gallery modes. The two-dimensional treatment should incorporate axial variations in “volumetric modes,”which have so far been presented in terms of Fabry–Perot (FP, and helical resonance modes. We report on finite-difference timedomain (FDTD simulations with the aim of identifying the dependence of these modes on geometry (length, width, tapering, shape (cylindrical, hexagonal, core–shell versus core-only, and dielectric cores with semiconductor shells. This demonstrates how nanowires (NWs form excellent optical cavities without the need for top and bottommirrors. However, optically equivalent structures such as hexagonal and cylindrical wires can have very different optoelectronic properties meaning that light management alone does not sufficiently describe the observed enhancement in upward (absorption and downward transitions (emission of light inNWs; rather, the electronic transition rates should be considered. We discuss this “rate management” scheme showing its strong dimensional dependence, making a case for photonic integrated circuits (PICs that can take advantage of the confluence of the desirable optical and electronic properties of these nanostructures.

  18. A Robust 96.6-dB-SNDR 50-kHz-Bandwidth Switched-Capacitor Delta-Sigma Modulator for IR Imagers in Space Instrumentation †

    Science.gov (United States)

    Dei, Michele; Sutula, Stepan; Cisneros, Jose; Pun, Ernesto; Jansen, Richard Jan Engel; Terés, Lluís; Serra-Graells, Francisco

    2017-01-01

    Infrared imaging technology, used both to study deep-space bodies’ radiation and environmental changes on Earth, experienced constant improvements in the last few years, pushing data converter designers to face new challenges in terms of speed, power consumption and robustness against extremely harsh operating conditions. This paper presents a 96.6-dB-SNDR (Signal-to-Noise-plus-Distortion Ratio) 50-kHz-bandwidth fourth-order single-bit switched-capacitor delta-sigma modulator for ADC operating at 1.8 V and consuming 7.9 mW fit for space instrumentation. The circuit features novel Class-AB single-stage switched variable-mirror amplifiers (SVMAs) enabling low-power operation, as well as low sensitivity to both process and temperature deviations for the whole modulator. The physical implementation resulted in a 1.8-mm2 chip integrated in a standard 0.18-μm 1-poly-6-metal (1P6M) CMOS technology, and it reaches a 164.6-dB Schreier figure of merit from experimental SNDR measurements without making use of any clock bootstrapping, analog calibration, nor digital compensation technique. When coupled to a 2048×2048 IR imager, the current design allows more than 50 frames per minute with a resolution of 16 effective number of bits (ENOB) while consuming less than 300 mW. PMID:28574466

  19. A Robust 96.6-dB-SNDR 50-kHz-Bandwidth Switched-Capacitor Delta-Sigma Modulator for IR Imagers in Space Instrumentation.

    Science.gov (United States)

    Dei, Michele; Sutula, Stepan; Cisneros, Jose; Pun, Ernesto; Jansen, Richard Jan Engel; Terés, Lluís; Serra-Graells, Francisco

    2017-06-02

    Infrared imaging technology, used both to study deep-space bodies' radiation and environmental changes on Earth, experienced constant improvements in the last few years, pushing data converter designers to face new challenges in terms of speed, power consumption and robustness against extremely harsh operating conditions. This paper presents a 96.6-dB-SNDR (Signal-to-Noise-plus-Distortion Ratio) 50-kHz-bandwidth fourth-order single-bit switched-capacitor delta-sigma modulator for ADC operating at 1.8 V and consuming 7.9 mW fit for space instrumentation. The circuit features novel Class-AB single-stage switched variable-mirror amplifiers (SVMAs) enabling low-power operation, as well as low sensitivity to both process and temperature deviations for the whole modulator. The physical implementation resulted in a 1.8-mm 2 chip integrated in a standard 0.18-µm 1-poly-6-metal (1P6M) CMOS technology, and it reaches a 164.6-dB Schreier figure of merit from experimental SNDR measurements without making use of any clock bootstrapping,analogcalibration,nordigitalcompensationtechnique. Whencoupledtoa2048×2048 IR imager, the current design allows more than 50 frames per minute with a resolution of 16 effective number of bits (ENOB) while consuming less than 300 mW.

  20. Optoelectronic analogue signal transfer for LHC detectors, 1991

    CERN Document Server

    Dowell, John D; Homer, R J; Jovanovic, P; Kenyon, I; Staley, R; Webster, K; Da Via, C; Feyt, J; Nappey, P; Stefanini, G; Dwir, B; Reinhart, F K; Davies, J; Green, N; Stewart, W; Young, T; Hall, G; Akesson, T; Jarlskog, G; Kröll, S; Nickerson, R; Jaroslawski, S; CERN. Geneva. Detector Research and Development Committee

    1991-01-01

    We propose to study and develop opto-electronic analogue front-ends based on electro-optic intensity modulators. These devices translate the detector electrical analogue signals into optical signals which are then transferred via optical fibres to photodetector receivers at the remote readout. In comparison with conventional solutions based on copper cables, this technique offers the advantages of high speed, very low power dissipation and transmission losses, compactness and immunity to electromagnetic interference. The linearity and dynamic range that can be obtained are more than adequate for central tracking detectors, and the proposed devices have considerable radiation- hardness capabilities. The large bandwidth and short transit times offer possibilities for improved triggering schemes. The proposed R&D programme is aimed at producing multi-channel "demonstrator" units for evaluation both in laboratory and beam tests. This will allow the choice of the most effective technology. A detailed study wil...

  1. Ultra-low Noise, High Bandwidth, 1550nm HgCdTe APD, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — To meet the demands of future high-capacity free space optical communications links, a high bandwidth, near infrared (NIR), single photon sensitive optoelectronic...

  2. Reconfigurable Integrated Optoelectronics

    Directory of Open Access Journals (Sweden)

    Richard Soref

    2011-01-01

    Full Text Available Integrated optics today is based upon chips of Si and InP. The future of this chip industry is probably contained in the thrust towards optoelectronic integrated circuits (OEICs and photonic integrated circuits (PICs manufactured in a high-volume foundry. We believe that reconfigurable OEICs and PICs, known as ROEICs and RPICs, constitute the ultimate embodiment of integrated photonics. This paper shows that any ROEIC-on-a-chip can be decomposed into photonic modules, some of them fixed and some of them changeable in function. Reconfiguration is provided by electrical control signals to the electro-optical building blocks. We illustrate these modules in detail and discuss 3D ROEIC chips for the highest-performance signal processing. We present examples of our module theory for RPIC optical lattice filters already constructed, and we propose new ROEICs for directed optical logic, large-scale matrix switching, and 2D beamsteering of a phased-array microwave antenna. In general, large-scale-integrated ROEICs will enable significant applications in computing, quantum computing, communications, learning, imaging, telepresence, sensing, RF/microwave photonics, information storage, cryptography, and data mining.

  3. Organic optoelectronic materials

    CERN Document Server

    Li, Yongfang

    2015-01-01

    This volume reviews the latest trends in organic optoelectronic materials. Each comprehensive chapter allows graduate students and newcomers to the field to grasp the basics, whilst also ensuring that they have the most up-to-date overview of the latest research. Topics include: organic conductors and semiconductors; conducting polymers and conjugated polymer semiconductors, as well as their applications in organic field-effect-transistors; organic light-emitting diodes; and organic photovoltaics and transparent conducting electrodes. The molecular structures, synthesis methods, physicochemical and optoelectronic properties of the organic optoelectronic materials are also introduced and described in detail. The authors also elucidate the structures and working mechanisms of organic optoelectronic devices and outline fundamental scientific problems and future research directions. This volume is invaluable to all those interested in organic optoelectronic materials.

  4. Chemical Industry Bandwidth Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-12-01

    The Chemical Bandwidth Study provides a snapshot of potentially recoverable energy losses during chemical manufacturing. The advantage of this study is the use of "exergy" analysis as a tool for pinpointing inefficiencies.

  5. Industrial Glass Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States); Servaites, James [Gas Technology Inst., Des Plaines, IL (United States); Wolf, Warren [Gas Technology Inst., Des Plaines, IL (United States)

    2007-08-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  6. Glass Industry Bandwidth Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Rue, David M. [Gas Technology Inst., Des Plaines, IL (United States)

    2006-07-01

    This is a study on energy use and potential savings, or "bandwidth" study, for several glassmaking processes. Intended to provide a realistic estimate of the potential amount of energy that can be saved in an industrial process, the "bandwidth" refers to the difference between the amount of energy that would be consumed in a process using commercially available technology versus the minimum amount of energy needed to achieve those same results.

  7. Monolithic optoelectronic integrated broadband optical receiver with graphene photodetectors

    Directory of Open Access Journals (Sweden)

    Cheng Chuantong

    2017-07-01

    Full Text Available Optical receivers with potentially high operation bandwidth and low cost have received considerable interest due to rapidly growing data traffic and potential Tb/s optical interconnect requirements. Experimental realization of 65 GHz optical signal detection and 262 GHz intrinsic operation speed reveals the significance role of graphene photodetectors (PDs in optical interconnect domains. In this work, a novel complementary metal oxide semiconductor post-backend process has been developed for integrating graphene PDs onto silicon integrated circuit chips. A prototype monolithic optoelectronic integrated optical receiver has been successfully demonstrated for the first time. Moreover, this is a firstly reported broadband optical receiver benefiting from natural broadband light absorption features of graphene material. This work is a perfect exhibition of the concept of monolithic optoelectronic integration and will pave way to monolithically integrated graphene optoelectronic devices with silicon ICs for three-dimensional optoelectronic integrated circuit chips.

  8. Monolithic optoelectronic integrated broadband optical receiver with graphene photodetectors

    Science.gov (United States)

    Cheng, Chuantong; Huang, Beiju; Mao, Xurui; Zhang, Zanyun; Zhang, Zan; Geng, Zhaoxin; Xue, Ping; Chen, Hongda

    2017-07-01

    Optical receivers with potentially high operation bandwidth and low cost have received considerable interest due to rapidly growing data traffic and potential Tb/s optical interconnect requirements. Experimental realization of 65 GHz optical signal detection and 262 GHz intrinsic operation speed reveals the significance role of graphene photodetectors (PDs) in optical interconnect domains. In this work, a novel complementary metal oxide semiconductor post-backend process has been developed for integrating graphene PDs onto silicon integrated circuit chips. A prototype monolithic optoelectronic integrated optical receiver has been successfully demonstrated for the first time. Moreover, this is a firstly reported broadband optical receiver benefiting from natural broadband light absorption features of graphene material. This work is a perfect exhibition of the concept of monolithic optoelectronic integration and will pave way to monolithically integrated graphene optoelectronic devices with silicon ICs for three-dimensional optoelectronic integrated circuit chips.

  9. Optoelectronics circuits manual

    CERN Document Server

    Marston, R M

    2013-01-01

    Optoelectronics Circuits Manual covers the basic principles and characteristics of the best known types of optoelectronic devices, as well as the practical applications of many of these optoelectronic devices. The book describes LED display circuits and LED dot- and bar-graph circuits and discusses the applications of seven-segment displays, light-sensitive devices, optocouplers, and a variety of brightness control techniques. The text also tackles infrared light-beam alarms and multichannel remote control systems. The book provides practical user information and circuitry and illustrations.

  10. Semiconductor opto-electronics

    CERN Document Server

    Moss, TS; Ellis, B

    1972-01-01

    Semiconductor Opto-Electronics focuses on opto-electronics, covering the basic physical phenomena and device behavior that arise from the interaction between electromagnetic radiation and electrons in a solid. The first nine chapters of this book are devoted to theoretical topics, discussing the interaction of electromagnetic waves with solids, dispersion theory and absorption processes, magneto-optical effects, and non-linear phenomena. Theories of photo-effects and photo-detectors are treated in detail, including the theories of radiation generation and the behavior of semiconductor lasers a

  11. FABRICATION, MORPHOLOGICAL AND OPTOELECTRONIC ...

    African Journals Online (AJOL)

    2014-12-31

    Dec 31, 2014 ... 1. INTRODUCTION. The direct band gab semiconductor offer much stronger absorption coefficient; therefore, the porous silicon has better optoelectronic properties than bulk silicon[1].The silicon ultraviolet photodetectors have many dramatic limitations, like the low quantum efficiency in the deep UV.

  12. Optoelectronics of Molecules and Polymers

    CERN Document Server

    Moliton, André

    2006-01-01

    Optoelectronic devices are being developed at an extraordinary rate. Organic light emitting diodes, photovoltaic devices and electro-optical modulators are pivotal to the future of displays, photosensors and solar cells, and communication technologies. This book details the theories underlying the relevant mechanisms in organic materials and covers, at a basic level, how the organic components are made. The first part of this book introduces the fundamental theories used to detail ordered solids and localised energy levels. The methods used to determine energy levels in perfectly ordered molecular and macromolecular systems are discussed, making sure that the effects of quasi-particles are not missed. The function of excitons and their transfer between two molecules are studied, and the problems associated with interfaces and charge injection into resistive media are presented. The second part details technological aspects such as the fabrication of devices based on organic materials by dry etching. The princ...

  13. Terahertz optoelectronics with surface plasmon polariton diode.

    Science.gov (United States)

    Vinnakota, Raj K; Genov, Dentcho A

    2014-05-09

    The field of plasmonics has experience a renaissance in recent years by providing a large variety of new physical effects and applications. Surface plasmon polaritons, i.e. the collective electron oscillations at the interface of a metal/semiconductor and a dielectric, may bridge the gap between electronic and photonic devices, provided a fast switching mechanism is identified. Here, we demonstrate a surface plasmon-polariton diode (SPPD) an optoelectronic switch that can operate at exceedingly large signal modulation rates. The SPPD uses heavily doped p-n junction where surface plasmon polaritons propagate at the interface between n and p-type GaAs and can be switched by an external voltage. The devices can operate at transmission modulation higher than 98% and depending on the doping and applied voltage can achieve switching rates of up to 1 THz. The proposed switch is compatible with the current semiconductor fabrication techniques and could lead to nanoscale semiconductor-based optoelectronics.

  14. A monolithically integrated magneto-optoelectronic circuit

    Science.gov (United States)

    Saha, D.; Basu, D.; Bhattacharya, P.

    2008-11-01

    The monolithic integration of a spin valve, an amplifier, and a light emitting diode to form a magneto-optoelectronic integrated circuit on GaAs is demonstrated. The circuit converts the spin polarization information in the channel of the spin valve to an amplified change in light intensity with a gain of 20. The monolithic circuit therefore operates as a magnetoelectronic switch which modulates the light intensity of the light emitting diode.

  15. Optimization of Quantum-Dot Molecular Beam Epitaxy for Broad Spectral Bandwidth Devices

    KAUST Repository

    Majid, Mohammed Abdul

    2012-12-01

    The optimization of the key growth parameters for broad spectral bandwidth devices based on quantum dots is reported. A combination of atomic force microscopy, photoluminescence of test samples, and optoelectronic characterization of superluminescent diodes (SLDs) is used to optimize the growth conditions to obtain high-quality devices with large spectral bandwidth, radiative efficiency (due to a reduced defective-dot density), and thus output power. The defective-dot density is highlighted as being responsible for the degradation of device performance. An SLD device with 160 nm of bandwidth centered at 1230 nm is demonstrated.

  16. Steps towards silicon optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Starovoytov, A

    1999-07-01

    This thesis addresses the issue of a potential future microelectronics technology, namely the possibility of utilising the optical properties of nanocrystalline silicon for optoelectronic circuits. The subject is subdivided into three chapters. Chapter 1 is an introduction. It formulates the oncoming problem for microelectronic development, explains the basics of Integrated Optoelectronics, introduces porous silicon as a new light-emitting material and gives a brief review of other competing light-emitting material systems currently under investigation. Examples of existing porous silicon devices are given. Chapter 2 reviews the basic physics relevant to the subject of this thesis and in-forms on the present situation in this field of research, including both experimental and theoretical knowledge gained up-to-date. The chapter provides the necessary background for correct interpretation of the results reported in Chapter 3 and for a realistic decision on the direction for future work. Chapter 3 describes my own experimental and computational results within the framework of the subject, obtained at De Montfort University. These include: one-step preparation of laterally structured porous silicon with photoluminescence and microscopy characterisation, Raman spectroscopy of porous silicon, a polarisation study of the photoluminescence from porous silicon, computer simulations of the conductivity of two-component media and of laser focused atomic deposition for nanostructure fabrication. Thus, this thesis makes a dual contribution to the chosen field: it summarises the present knowledge on the possibility of utilising optical properties of nanocrystalline silicon in silicon-based electronics, and it reports new results within the framework of the subject. The main conclusion is that due to its promising optoelectronic properties nanocrystalline silicon remains a prospective competitor for the cheapest and fastest microelectronics of the next century. (author)

  17. Semiconductor characterization for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Miner, C.J. [Bell Northern Research Ltd., Ottawa, ON (Canada)

    1996-03-01

    Scanning reflectance spectroscopy, scanning photoluminescence, and double crystal x-ray diffraction mapping are all specialized non-destructive characterization tools which monitor the advanced materials used in the development of high speed optoelectronics. Each technology was described and their application in the assessment of III-V semiconductor composition, layer thickness and defect density was demonstrated. The new techniques have been optimized for speed, to make high spatial resolution mapping practical. Since the tests are non-destructive, frequent monitoring is possible. 11 refs., 7 figs.

  18. Estimating Bottleneck Bandwidth using TCP

    Science.gov (United States)

    Allman, Mark

    1998-01-01

    Various issues associated with estimating bottleneck bandwidth using TCP are presented in viewgraph form. Specific topics include: 1) Why TCP is wanted to estimate the bottleneck bandwidth; 2) Setting ssthresh to an appropriate value to reduce loss; 3) Possible packet-pair solutions; and 4) Preliminary results: ACTS and the Internet.

  19. Upgrade trigger: Bandwidth strategy proposal

    CERN Document Server

    Fitzpatrick, Conor; Meloni, Simone; Boettcher, Thomas Julian; Whitehead, Mark Peter; Dziurda, Agnieszka; Vesterinen, Mika Anton

    2017-01-01

    This document describes a selection strategy for the upgrade trigger using charm signals as a benchmark. The Upgrade trigger uses a 'Run 2-like' sequence consisting of a first and second stage, in between which the calibration and alignment is performed. The first stage, HLT1, uses an inclusive strategy to select beauty and charm decays, while the second stage uses offline-quality exclusive selections. A novel genetic algorithm-based bandwidth division is performed at the second stage to distribute the output bandwidth among different physics channels, maximising the efficiency for useful physics events. The performance is then studied as a function of the available output bandwidth.

  20. Photonic Structure-Integrated Two-Dimensional Material Optoelectronics

    Directory of Open Access Journals (Sweden)

    Tianjiao Wang

    2016-12-01

    Full Text Available The rapid development and unique properties of two-dimensional (2D materials, such as graphene, phosphorene and transition metal dichalcogenides enable them to become intriguing candidates for future optoelectronic applications. To maximize the potential of 2D material-based optoelectronics, various photonic structures are integrated to form photonic structure/2D material hybrid systems so that the device performance can be manipulated in controllable ways. Here, we first introduce the photocurrent-generation mechanisms of 2D material-based optoelectronics and their performance. We then offer an overview and evaluation of the state-of-the-art of hybrid systems, where 2D material optoelectronics are integrated with photonic structures, especially plasmonic nanostructures, photonic waveguides and crystals. By combining with those photonic structures, the performance of 2D material optoelectronics can be further enhanced, and on the other side, a high-performance modulator can be achieved by electrostatically tuning 2D materials. Finally, 2D material-based photodetector can also become an efficient probe to learn the light-matter interactions of photonic structures. Those hybrid systems combine the advantages of 2D materials and photonic structures, providing further capacity for high-performance optoelectronics.

  1. Deformable paper origami optoelectronic devices

    KAUST Repository

    He, Jr-Hau

    2017-01-19

    Deformable optoelectronic devices are provided, including photodetectors, photodiodes, and photovoltaic cells. The devices can be made on a variety of paper substrates, and can include a plurality of fold segments in the paper substrate creating a deformable pattern. Thin electrode layers and semiconductor nanowire layers can be attached to the substrate, creating the optoelectronic device. The devices can be highly deformable, e.g. capable of undergoing strains of 500% or more, bending angles of 25° or more, and/or twist angles of 270° or more. Methods of making the deformable optoelectronic devices and methods of using, e.g. as a photodetector, are also provided.

  2. InP based optoelectronics

    Science.gov (United States)

    Pütz, Norbert

    1991-01-01

    Optoelectronic devices involving epitaxial layers grown by MOCVD within the GaInAsP and GaInAlAs material systems lattice matched to InP are reviewed. Besides discrete long wavelength (1 MOCVD technique are presented.

  3. Network bandwidth utilization forecast model on high bandwidth networks

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Wuchert (William) [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sim, Alex [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

    2015-03-30

    With the increasing number of geographically distributed scientific collaborations and the scale of the data size growth, it has become more challenging for users to achieve the best possible network performance on a shared network. We have developed a forecast model to predict expected bandwidth utilization for high-bandwidth wide area network. The forecast model can improve the efficiency of resource utilization and scheduling data movements on high-bandwidth network to accommodate ever increasing data volume for large-scale scientific data applications. Univariate model is developed with STL and ARIMA on SNMP path utilization data. Compared with traditional approach such as Box-Jenkins methodology, our forecast model reduces computation time by 83.2%. It also shows resilience against abrupt network usage change. The accuracy of the forecast model is within the standard deviation of the monitored measurements.

  4. Network Bandwidth Utilization Forecast Model on High Bandwidth Network

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Wucherl; Sim, Alex

    2014-07-07

    With the increasing number of geographically distributed scientific collaborations and the scale of the data size growth, it has become more challenging for users to achieve the best possible network performance on a shared network. We have developed a forecast model to predict expected bandwidth utilization for high-bandwidth wide area network. The forecast model can improve the efficiency of resource utilization and scheduling data movements on high-bandwidth network to accommodate ever increasing data volume for large-scale scientific data applications. Univariate model is developed with STL and ARIMA on SNMP path utilization data. Compared with traditional approach such as Box-Jenkins methodology, our forecast model reduces computation time by 83.2percent. It also shows resilience against abrupt network usage change. The accuracy of the forecast model is within the standard deviation of the monitored measurements.

  5. Radiation effects in optoelectronic devices

    International Nuclear Information System (INIS)

    Barnes, C.E.; Wiczer, J.J.

    1984-05-01

    Purpose of this report is to provide not only a summary of radiation damage studies at Sandia National Laboratories, but also of those in the literature on the components of optoelectronic systems: light emitting diodes (LEDs), laser diodes, photodetectors, optical fibers, and optical isolators. This review of radiation damage in optoelectronic components is structured according to device type. In each section, a brief discussion of those device properties relevant to radiation effects is given

  6. High-bandwidth memory interface

    CERN Document Server

    Kim, Chulwoo; Song, Junyoung

    2014-01-01

    This book provides an overview of recent advances in memory interface design at both the architecture and circuit levels. Coverage includes signal integrity and testing, TSV interface, high-speed serial interface including equalization, ODT, pre-emphasis, wide I/O interface including crosstalk, skew cancellation, and clock generation and distribution. Trends for further bandwidth enhancement are also covered.   • Enables readers with minimal background in memory design to understand the basics of high-bandwidth memory interface design; • Presents state-of-the-art techniques for memory interface design; • Covers memory interface design at both the circuit level and system architecture level.

  7. Mining Industry Energy Bandwidth Study

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2007-07-01

    The Industrial Technologies Program (ITP) relies on analytical studies to identify large energy reduction opportunities in energy-intensive industries and uses these results to guide its R&D portfolio. The energy bandwidth illustrates the total energy-saving opportunity that exists in the industry if the current processes are improved by implementing more energy-efficient practices and by using advanced technologies. This bandwidth analysis report was conducted to assist the ITP Mining R&D program in identifying energy-saving opportunities in coal, metals, and mineral mining. These opportunities were analyzed in key mining processes of blasting, dewatering, drilling, digging, ventilation, materials handling, crushing, grinding, and separations.

  8. Black holes, bandwidths and Beethoven

    Science.gov (United States)

    Kempf, Achim

    2000-04-01

    It is usually believed that a function φ(t) whose Fourier spectrum is bounded can vary at most as fast as its highest frequency component ωmax. This is, in fact, not the case, as Aharonov, Berry, and others drastically demonstrated with explicit counterexamples, so-called superoscillations. It has been claimed that even the recording of an entire Beethoven symphony can occur as part of a signal with a 1 Hz bandwidth. Bandlimited functions also occur as ultraviolet regularized fields. Their superoscillations have been suggested, for example, to resolve the trans-Planckian frequencies problem of black hole radiation. Here, we give an exact proof for generic superoscillations. Namely, we show that for every fixed bandwidth there exist functions that pass through any finite number of arbitrarily prespecified points. Further, we show that, in spite of the presence of superoscillations, the behavior of bandlimited functions can be characterized reliably, namely through an uncertainty relation: The standard deviation ΔT of samples φ(tn) taken at the Nyquist rate obeys ΔT>=1/4ωmax. This uncertainty relation generalizes to variable bandwidths. For ultraviolet regularized fields we identify the bandwidth as the in general spatially variable finite local density of degrees of freedom.

  9. Semiconductor optoelectronic infrared spectroscopy

    International Nuclear Information System (INIS)

    Hollingworth, A.R.

    2001-08-01

    We use spectroscopy to study infrared optoelectronic inter and intraband semiconductor carrier dynamics. The overall aim of this thesis was to study both III-V and Pb chalcogenide material systems in order to show their future potential use in infrared emitters. The effects of bandstructure engineering have been studied in the output characteristics of mid-IR III-V laser diodes to show which processes (defects, radiative, Auger and phonon) dominate and whether non-radiative processes can be suppressed. A new three-beam pump probe experiment was used to investigate interband recombination directly in passive materials. Experiments on PbSe and theory for non-parabolic near-mirror bands and non-degenerate statistics were in good agreement. Comparisons with HgCdTe showed a reduction in the Auger coefficient of 1-2 orders of magnitude in the PbSe. Using Landau confinement to model spatial confinement in quantum dots (QDs) 'phonon bottlenecking' was studied. The results obtained from pump probe and cyclotron resonance saturation measurements showed a clear suppression in the cooling of carriers when Landau level separation was not resonant with LO phonon energy. When a bulk laser diode was placed in a magnetic field to produce a quasi quantum wire device the resulting enhanced differential gain and reduced Auger recombination lowered I th by 30%. This result showed many peaks in the light output which occurred when the LO phonon energy was a multiple of the Landau level separation. This showed for the first time evidence of the phonon bottleneck in a working laser device. A new technique called time resolved optically detected cyclotron resonance, was used as a precursor to finding the carrier dynamics within a spatially confined quantum dot. By moving to the case of a spatial QD using an optically detected intraband resonance it was possible to measure the energy separation interband levels and conduction and valence sublevels within the dot simultaneously. Furthermore

  10. Optoelectronics laboratory annual report, 1994

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-12-31

    The research projects completed or being pursued in 1994 at Optoelectronics Laboratory are described in the detailed research reports, which consist the major part of this annual report. A large amount of this work is financed, in part at least, from sources outside the University. The three-year research contract signed by the Helsinki University of Technology, its Optoelectronics Laboratory and the Academy of Finland ended in 1994. It aimed at developing advanced technologies for optoelectronic components and new semiconductor heterostructures. The research programme was divided into three subprojects: MOVPE (metalorganic vapor phase epitaxy) and materials characterisation, surface emitting lasers having vertical cavity, and cold trapping of atoms with semiconductor laser beams. The research was carried out jointly with the Photonics Division of the Electronic Materials and Components VTT Electronics and the Metrology Research Institute of the Helsinki University of Technology.

  11. An introduction to optoelectronic sensors

    CERN Document Server

    Tajani, Antonella; Cutolo, Antonello

    2009-01-01

    This invaluable book offers a comprehensive overview of the technologies and applications of optoelectronic sensors. Based on the R&D experience of more than 70 engineers and scientists, highly representative of the Italian academic and industrial community in this area, this book provides a broad and accurate description of the state-of-the-art optoelectronic technologies for sensing. The most innovative approaches, such as the use of photonic crystals, squeezed states of light and microresonators for sensing, are considered. Application areas range from environment to medicine and healthcare

  12. SiGe/Si electronics and optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Wang, K.L.; Karunasiri, R.P.G. [Univ. of California, Los Angeles, CA (United States)

    1993-05-01

    Recently, there is an increased interest in the use of SiGe layered material for integration with Si technology. SiGe offers the opportunity for the first time to realize the advantages of heterojunctions in Si-based technology. In this article, the present status of the SiGe epitaxial growth techniques will be discussed from the point of view of device application. New directions will be presented. Next, electronic devices to be reviewed include bipolars and field effect transistors. The progress of tunneling devices will also be discussed. Then, the realization of quantum wells and superlattices for optoelectronics will be discussed. Then, the realization of quantum wells and superlattices for optoelectronics will be discussed. These will include Si-based detectors and modulators based on interband and intersubband transitions. One of the focuses will be the normal incidence operation for intersubband devices. Finally, the current status in the quest of light emitters will be briefly addressed. 44 refs., 15 figs.

  13. Bandwidth utilization maximization of scientific RF communication systems

    Energy Technology Data Exchange (ETDEWEB)

    Rey, D. [Sandia National Lab., Albuquerque, NM (United States); Ryan, W. [New Mexico State Univ., Las Cruces, NM (United States); Ross, M.

    1997-01-01

    A method for more efficiently utilizing the frequency bandwidth allocated for data transmission is presented. Current space and range communication systems use modulation and coding schemes that transmit 0.5 to 1.0 bits per second per Hertz of radio frequency bandwidth. The goal in this LDRD project is to increase the bandwidth utilization by employing advanced digital communications techniques. This is done with little or no increase in the transmit power which is usually very limited on airborne systems. Teaming with New Mexico State University, an implementation of trellis coded modulation (TCM), a coding and modulation scheme pioneered by Ungerboeck, was developed for this application and simulated on a computer. TCM provides a means for reliably transmitting data while simultaneously increasing bandwidth efficiency. The penalty is increased receiver complexity. In particular, the trellis decoder requires high-speed, application-specific digital signal processing (DSP) chips. A system solution based on the QualComm Viterbi decoder and the Graychip DSP receiver chips is presented.

  14. Optoelectronic properties of semiconductor nanostructures

    Science.gov (United States)

    Maher, Kristin Nicole

    Semiconductor nanostructures have unique optical and electronic properties that have inspired research into their technological applications and basic science. This thesis presents approaches to the fabrication and characterization of optoelectronic devices incorporating individual semiconductor nanostructures. Nanowires of the II-VI semiconductors CdSe and CdS were synthesized using nanoparticle-catalysed solution-liquid-solid growth. Single-component nanowires and heterostructure nanowires with axial compositional modulation were generated using this method. Individual nanowires and nanocrystals were then incorporated into devices with a three-terminal field-effect transistor geometry. An experimental platform was developed which allows for simultaneous electrical characterization of devices and measurement of their optical properties. This setup enables the measurement of spatially and spectrally resolved electroluminescence (EL) and photoluminescence (PL) from individual nanostructures and nanostructure devices. It also allows the measurement of photon coincidence histograms for emitted light and the acquisition of photocurrent images via laser scanning microscopy. Electroluminescence was observed from individual CdSe nanocrystals contacted by gold electrodes. Concomitant transport measurements at low temperature showed clear evidence of Coulomb blockade at low bias voltage, with light only emitted from devices exhibiting asymmetric tunnel couplings between the nanocrystal and electrodes. Combined analyses of the data indicate that the resistances of the tunnel barriers are bias voltage dependent and that light emission results from the inelastic scattering of tunneling electrons. Three-terminal devices incorporating individual CdSe nanoNvires exhibited EL localized near the positively-biased electrode. Characterization of these devices by scanning photocurrent microscopy (SPCM) and Kelvin probe microscopy (KPM) indicates that while there are n-type Schottky

  15. Hybrid optoelectronic device with multiple bistable outputs

    Science.gov (United States)

    Costazo-Caso, Pablo A.; Jin, Yiye; Gelh, Michael; Granieri, Sergio; Siahmakoun, Azad

    2011-01-01

    Optoelectronic circuits which exhibit optical and electrical bistability with hysteresis behavior are proposed and experimentally demonstrated. The systems are based on semiconductor optical amplifiers (SOA), bipolar junction transistors (BJT), PIN photodiodes (PD) and laser diodes externally modulated with integrated electro-absorption modulators (LD-EAM). The device operates based on two independent phenomena leading to both electrical bistability and optical bistability. The electrical bistability is due to the series connection of two p-i-n structures (SOA, BJT, PD or LD) in reverse bias. The optical bistability is consequence of the quantum confined Stark effect (QCSE) in the multi-quantum well (MQW) structure in the intrinsic region of the device. This effect produces the optical modulation of the transmitted light through the SOA (or reflected from the PD). Finally, because the optical transmission of the SOA (in reverse bias) and the reflected light from the PD are so small, a LD-EAM modulated by the voltage across these devices are employed to obtain a higher output optical power. Experiments show that the maximum switching frequency is in MHz range and the rise/fall times lower than 1 us. The temporal response is mainly limited by the electrical capacitance of the devices and the parasitic inductances of the connecting wires. The effects of these components can be reduced in current integration technologies.

  16. Moiré volume Bragg grating filter with tunable bandwidth.

    Science.gov (United States)

    Mokhov, Sergiy; Ott, Daniel; Divliansky, Ivan; Zeldovich, Boris; Glebov, Leonid

    2014-08-25

    We propose a monolithic large-aperture narrowband optical filter based on a moiré volume Bragg grating formed by two sequentially recorded gratings with slightly different resonant wavelengths. Such recording creates a spatial modulation of refractive index with a slowly varying sinusoidal envelope. By cutting a specimen at a small angle, to a thickness of one-period of this envelope, the longitudinal envelope profile will shift from a sine profile to a cosine profile across the face of the device. The transmission peak of the filter has a tunable bandwidth while remaining at a fixed resonant wavelength by a transversal shift of incidence position. Analytical expressions for the tunable bandwidth of such a filter are calculated and experimental data from a filter operating at 1064 nm with bandwidth range 30-90 pm is demonstrated.

  17. Optical computing for image bandwidth compression: analysis and simulation.

    Science.gov (United States)

    Hunt, B R

    1978-09-15

    Image bandwidth compression is dominated by digital methods for carrying out the required computations. This paper discusses the general problem of using optics to realize the computations in bandwidth compression. A common method of digital bandwidth compression, feedback differential pulse code modulation (DPCM), is reviewed, and the obstacles to making a direct optical analogy to feedback DPCM are discussed. Instead of a direct optical analogy to DPCM, an optical system which captures the essential features of DPCM without optical feedback is introduced. The essential features of this incoherent optical system are encoding of low-frequency information and generation of difference samples which can be coded with a small number of bits. A simulation of this optical system by means of digital image processing is presented, and performance data are also included.

  18. Microwave photonic single-passband filter with highly flexible tunability of bandwidth and frequency

    Science.gov (United States)

    Xu, Enming; Han, Xiuyou

    2017-01-01

    A microwave photonic single-passband filter with highly flexible tunability of bandwidth and frequency is proposed and demonstrated. Two different light waves with their polarizations aligned with two principal axes of a polarization modulator are modulated, and two phase-modulated signals with opposite phase modulation indices are generated. Two different lower parts of the lower sidebands are removed by a fiber Bragg grating to convert two phase-modulated signals into two intensity-modulated signals. Two high-pass frequency responses with different cut-off frequencies are realized. Since the two converted intensity-modulated signals are out of phase, the overlapped frequency responses are cancelled, and a single-passband filter is realized. The bandwidth and the central frequency can be tuned independently by properly adjusting the two wavelengths simultaneously. Furthermore, both the bandwidth and the central frequency can be simultaneously tuned by adjusting one of the two wavelengths.

  19. Piezophototronic Effect in Single-Atomic-Layer MoS 2 for Strain-Gated Flexible Optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Wenzhuo [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta GA 30332-0245 USA; Wang, Lei [Department of Electrical Engineering, Columbia University, New York NY 10027 USA; Yu, Ruomeng [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta GA 30332-0245 USA; Liu, Yuanyue [National Renewable Energy Laboratory (NREL), Golden CO 80401 USA; Wei, Su-Huai [National Renewable Energy Laboratory (NREL), Golden CO 80401 USA; Hone, James [Department of Mechanical Engineering, Columbia University, New York NY 10027 USA; Wang, Zhong Lin [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta GA 30332-0245 USA; Beijing Institute of Nanoenergy and Nanosystems, Chinese Academy of Sciences, 100083 Beijing China

    2016-08-03

    Strain-gated flexible optoelectronics are reported based on monolayer MoS2. Utilizing the piezoelectric polarization created at metal-MoS2 interface to modulate the separation/transport of photogenerated carriers, the piezophototronic effect is applied to implement atomic-layer-thick phototransistor. Coupling between piezoelectricity and photogenerated carriers may enable the development of novel optoelectronics.

  20. Optoelectronic Implementation of Neural Networks

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 9. Optoelectronic Implementation of Neural Networks - Use of Optics in Computing. R Ramachandran. General Article Volume 3 Issue 9 September 1998 pp 45-55. Fulltext. Click here to view fulltext PDF. Permanent link:

  1. Optoelectronics in TESLA, LHC and pi-of-the-sky experiments

    CERN Document Server

    Romaniuk, Ryszard; Simrock, Stefan; Wrochna, Grzegorz

    2004-01-01

    Optical and optoelectronics technologies are more and more widely used in the biggest world experiments of high energy and nuclear physics, as well as in the astronomy. The paper is a kind of a broad digest describing the usage of optoelectronics is such experiments and information about some of the involved teams. The described experiments include: TESLA linear accelerator and FEL, Compact Muon Solenoid at LHC and recently started pi-of-the-sky global gamma ray bursts (with associated optical flashes) observation experiment. Optoelectronics and photonics offer several key features which are either extending the technical parameters of existing solutions or adding quite new practical application possibilities. Some of these favorable features of photonic systems are: high selectivity of optical sensors, immunity to some kinds of noise processes, extremely broad bandwidth exchangeable for either terabit rate transmission or ultrashort pulse generation, parallel image processing capability, etc. The following g...

  2. Optoelectronic circuits in nanometer CMOS technology

    CERN Document Server

    Atef, Mohamed

    2016-01-01

    This book describes the newest implementations of integrated photodiodes fabricated in nanometer standard CMOS technologies. It also includes the required fundamentals, the state-of-the-art, and the design of high-performance laser drivers, transimpedance amplifiers, equalizers, and limiting amplifiers fabricated in nanometer CMOS technologies. This book shows the newest results for the performance of integrated optical receivers, laser drivers, modulator drivers and optical sensors in nanometer standard CMOS technologies. Nanometer CMOS technologies rapidly advanced, enabling the implementation of integrated optical receivers for high data rates of several Giga-bits per second and of high-pixel count optical imagers and sensors. In particular, low cost silicon CMOS optoelectronic integrated circuits became very attractive because they can be extensively applied to short-distance optical communications, such as local area network, chip-to-chip and board-to-board interconnects as well as to imaging and medical...

  3. Limit characteristics of digital optoelectronic processor

    Science.gov (United States)

    Kolobrodov, V. G.; Tymchik, G. S.; Kolobrodov, M. S.

    2018-01-01

    In this article, the limiting characteristics of a digital optoelectronic processor are explored. The limits are defined by diffraction effects and a matrix structure of the devices for input and output of optical signals. The purpose of a present research is to optimize the parameters of the processor's components. The developed physical and mathematical model of DOEP allowed to establish the limit characteristics of the processor, restricted by diffraction effects and an array structure of the equipment for input and output of optical signals, as well as to optimize the parameters of the processor's components. The diameter of the entrance pupil of the Fourier lens is determined by the size of SLM and the pixel size of the modulator. To determine the spectral resolution, it is offered to use a concept of an optimum phase when the resolved diffraction maxima coincide with the pixel centers of the radiation detector.

  4. Mid-infrared Semiconductor Optoelectronics

    CERN Document Server

    Krier, Anthony

    2006-01-01

    The practical realisation of optoelectronic devices operating in the 2–10 µm (mid-infrared) wavelength range offers potential applications in a variety of areas from environmental gas monitoring around oil rigs and landfill sites to the detection of pharmaceuticals, particularly narcotics. In addition, an atmospheric transmission window exists between 3 µm and 5 µm that enables free-space optical communications, thermal imaging applications and the development of infrared measures for "homeland security". Consequently, the mid-infrared is very attractive for the development of sensitive optical sensor instrumentation. Unfortunately, the nature of the likely applications dictates stringent requirements in terms of laser operation, miniaturisation and cost that are difficult to meet. Many of the necessary improvements are linked to a better ability to fabricate and to understand the optoelectronic properties of suitable high-quality epitaxial materials and device structures. Substantial progress in these m...

  5. Optoelectronic device for hematocrit measurements

    Science.gov (United States)

    Pluta, M.; Milewska, D.; Mazikowski, A.

    2015-09-01

    An optoelectronic system for measurements of hematocrit level (HCT) in the whole human blood is presented. Proposed system integrates a dedicated optoelectronic sensor, a microcontroller and a small LCD display in a low cost, battery-powered, handheld device. Chosen method for determining blood hematocrit level is based on optical properties of whole blood in visible and NIR wavelength range. Measurements with the use of proposed system require blood samples (small drop in the range of microliters) which is placed in the micro cuvette. Then, absorption of the sample is measured at wavelengths of 570 nm and 880 nm. Prototype of the device was build and tested. Test results confirmed proper operation of the device with correct metrological parameters in application to HCT level measurements. Such a portable device can be used as a tool of bedside diagnosis, which becomes interesting alternative to full laboratory tests.

  6. Lasers and optoelectronics fundamentals, devices and applications

    CERN Document Server

    Maini, Anil K

    2013-01-01

    With emphasis on the physical and engineering principles, this book provides a comprehensive and highly accessible treatment of modern lasers and optoelectronics. Divided into four parts, it explains laser fundamentals, types of lasers, laser electronics & optoelectronics, and laser applications, covering each of the topics in their entirety, from basic fundamentals to advanced concepts. Key features include: exploration of technological and application-related aspects of lasers and optoelectronics, detailing both existing and emerging applications in industry, medical diag

  7. Controlling Laser Plasma Instabilities Using Temporal Bandwidth

    Science.gov (United States)

    Tsung, Frank; Weaver, J.; Lehmberg, R.

    2016-10-01

    We are performing particle-in-cell simulations using the code OSIRIS to study the effects of laser plasma interactions in the presence of temporal bandwidth under conditions relevant to current and future experiments on the NIKE laser. Our simulations show that, for sufficiently large bandwidth (where the inverse bandwidth is comparable with the linear growth time), the saturation level, and the distribution of hot electrons, can be effected by the addition of temporal bandwidths (which can be accomplished in experiments using beam smoothing techniques such as ISI). We will quantify these effects and investigate higher dimensional effects such as laser speckles. This work is supported by DOE and NRL.

  8. Real-Time Optimization Of Receiver Bandwidth

    Science.gov (United States)

    Vilnrotter, V. A.; Hurd, W. J.; Brown, D. H.

    1989-01-01

    Estimates of signal and noise spectra enhance reception of weak signals. Carrier-tracking phase-locked loop represented by linear mathematical model at small rms phase errors. Loop continuously generates estimates of received phase. Bandwidth (in effect, scale of complex-frequency variable p) optimized to minimize rms phase error. Minimum signals tracked 5 to 15 dB below those tracked by current receivers. Improvement accomplished by use of bandwidths of 0.1 to 1.0 Hz, in contrast with 3-Hz bandwidth in current use. Principle of real-time optimization of bandwidth adapted to other situations to enhance reception of weak signals otherwise "buried" in noise.

  9. Small Molecule Organic Optoelectronic Devices

    Science.gov (United States)

    Bakken, Nathan

    Organic optoelectronics include a class of devices synthesized from carbon containing 'small molecule' thin films without long range order crystalline or polymer structure. Novel properties such as low modulus and flexibility as well as excellent device performance such as photon emission approaching 100% internal quantum efficiency have accelerated research in this area substantially. While optoelectronic organic light emitting devices have already realized commercial application, challenges to obtain extended lifetime for the high energy visible spectrum and the ability to reproduce natural white light with a simple architecture have limited the value of this technology for some display and lighting applications. In this research, novel materials discovered from a systematic analysis of empirical device data are shown to produce high quality white light through combination of monomer and excimer emission from a single molecule: platinum(II) bis(methyl-imidazolyl)toluene chloride (Pt-17). Illumination quality achieved Commission Internationale de L'Eclairage (CIE) chromaticity coordinates (x = 0.31, y = 0.38) and color rendering index (CRI) > 75. Further optimization of a device containing Pt-17 resulted in a maximum forward viewing power efficiency of 37.8 lm/W on a plain glass substrate. In addition, accelerated aging tests suggest high energy blue emission from a halogen-free cyclometalated platinum complex could demonstrate degradation rates comparable to known stable emitters. Finally, a buckling based metrology is applied to characterize the mechanical properties of small molecule organic thin films towards understanding the deposition kinetics responsible for an elastic modulus that is both temperature and thickness dependent. These results could contribute to the viability of organic electronic technology in potentially flexible display and lighting applications. The results also provide insight to organic film growth kinetics responsible for optical

  10. Optoelectronic tweezers for medical diagnostics

    Science.gov (United States)

    Kremer, Clemens; Neale, Steven; Menachery, Anoop; Barrett, Mike; Cooper, Jonathan M.

    2012-01-01

    Optoelectronic tweezers (OET) allows the spatial patterning of electric fields through selected illumination of a photoconductive surface. This enables the manipulation of micro particles and cells by creating non-uniform electrical fields that then produce dielectrophoretic (DEP) forces. The DEP responses of cells differ and can produce negative or positive (repelled or attracted to areas of high electric field) forces. Therefore OET can be used to manipulate individual cells and separate different cell types from each other. Thus OET has many applications for medical diagnostics, demonstrated here with work towards diagnosing Human African Trypanosomiasis, also known as sleeping sickness.

  11. Optoelectronics with 2D semiconductors

    Science.gov (United States)

    Mueller, Thomas

    2015-03-01

    Two-dimensional (2D) atomic crystals, such as graphene and layered transition-metal dichalcogenides, are currently receiving a lot of attention for applications in electronics and optoelectronics. In this talk, I will review our research activities on electrically driven light emission, photovoltaic energy conversion and photodetection in 2D semiconductors. In particular, WSe2 monolayer p-n junctions formed by electrostatic doping using a pair of split gate electrodes, type-II heterojunctions based on MoS2/WSe2 and MoS2/phosphorene van der Waals stacks, 2D multi-junction solar cells, and 3D/2D semiconductor interfaces will be presented. Upon optical illumination, conversion of light into electrical energy occurs in these devices. If an electrical current is driven, efficient electroluminescence is obtained. I will present measurements of the electrical characteristics, the optical properties, and the gate voltage dependence of the device response. In the second part of my talk, I will discuss photoconductivity studies of MoS2 field-effect transistors. We identify photovoltaic and photoconductive effects, which both show strong photoconductive gain. A model will be presented that reproduces our experimental findings, such as the dependence on optical power and gate voltage. We envision that the efficient photon conversion and light emission, combined with the advantages of 2D semiconductors, such as flexibility, high mechanical stability and low costs of production, could lead to new optoelectronic technologies.

  12. Bandwidth engineering of photonic crystal waveguide bends

    DEFF Research Database (Denmark)

    Borel, Peter Ingo; Frandsen, Lars Hagedorn; Harpøth, Anders

    2004-01-01

    An effective design principle has been applied to photonic crystal waveguide bends fabricated in silicon-on-insulator material using deep UV lithography resulting in a large increase in the low-loss bandwidth of the bends. Furthermore, it is experimentally demonstrated that the absolute bandwidth...... range can be adjusted in a post-fabrication thermal oxidation process....

  13. Bandwidth engineering of photonic crystal waveguide bends

    DEFF Research Database (Denmark)

    Borel, Peter Ingo; Frandsen, Lars Hagedorn; Harpøth, Anders

    2004-01-01

    An effective design principle has been applied to photonic crystal waveguide bends fabricated in silicon-on-insulator material using deep UV lithography resulting in a large increase in the low-loss bandwidth of the bends. Furthermore, it is experimentally demonstrated that the absolute bandwidth...

  14. 3 Approaches to Achieve Bandwidth Capacity

    Indian Academy of Sciences (India)

    First page Back Continue Last page Overview Graphics. 3 Approaches to Achieve Bandwidth Capacity. Install new fiber. Average cost $70,000 per mile. Right of way. Higher bandwidth on SONET/TDM. Single mode fiber high dispersion rate. NZDSF cost some 50 percent more than SMF. DWDM. Multi Wavelength Switching ...

  15. Energy Bandwidth for Petroleum Refining Processes

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2006-10-01

    The petroleum refining energy bandwidth report analyzes the most energy-intensive unit operations used in U.S. refineries: crude oil distillation, fluid catalytic cracking, catalytic hydrotreating, catalytic reforming, and alkylation. The "bandwidth" provides a snapshot of the energy losses that can potentially be recovered through best practices and technology R&D.

  16. 2D Organic Materials for Optoelectronic Applications.

    Science.gov (United States)

    Yang, Fangxu; Cheng, Shanshan; Zhang, Xiaotao; Ren, Xiaochen; Li, Rongjin; Dong, Huanli; Hu, Wenping

    2018-01-01

    The remarkable merits of 2D materials with atomically thin structures and optoelectronic attributes have inspired great interest in integrating 2D materials into electronics and optoelectronics. Moreover, as an emerging field in the 2D-materials family, assembly of organic nanostructures into 2D forms offers the advantages of molecular diversity, intrinsic flexibility, ease of processing, light weight, and so on, providing an exciting prospect for optoelectronic applications. Herein, the applications of organic 2D materials for optoelectronic devices are a main focus. Material examples include 2D, organic, crystalline, small molecules, polymers, self-assembly monolayers, and covalent organic frameworks. The protocols for 2D-organic-crystal-fabrication and -patterning techniques are briefly discussed, then applications in optoelectronic devices are introduced in detail. Overall, an introduction to what is known and suggestions for the potential of many exciting developments are presented. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  17. Advances in graphene-based optoelectronics, plasmonics and photonics

    International Nuclear Information System (INIS)

    Nguyen, Bich Ha; Nguyen, Van Hieu

    2016-01-01

    Since the early works on graphene it has been remarked that graphene is a marvelous electronic material. Soon after its discovery, graphene was efficiently utilized in the fabrication of optoelectronic, plasmonic and photonic devices, including graphene-based Schottky junction solar cells. The present work is a review of the progress in the experimental research on graphene-based optoelectronics, plasmonics and photonics, with the emphasis on recent advances. The main graphene-based optoelectronic devices presented in this review are photodetectors and modulators. In the area of graphene-based plasmonics, a review of the plasmonic nanostructures enhancing or tuning graphene-light interaction, as well as of graphene plasmons is presented. In the area of graphene-based photonics, we report progress on fabrication of different types of graphene quantum dots as well as functionalized graphene and graphene oxide, the research on the photoluminescence and fluorescence of graphene nanostructures as well as on the energy exchange between graphene and semiconductor quantum dots. In particular, the promising achievements of research on graphene-based Schottky junction solar cells is presented. (review)

  18. Transparent Electrodes for Efficient Optoelectronics

    KAUST Repository

    Morales-Masis, Monica

    2017-03-30

    With the development of new generations of optoelectronic devices that combine high performance and novel functionalities (e.g., flexibility/bendability, adaptability, semi or full transparency), several classes of transparent electrodes have been developed in recent years. These range from optimized transparent conductive oxides (TCOs), which are historically the most commonly used transparent electrodes, to new electrodes made from nano- and 2D materials (e.g., metal nanowire networks and graphene), and to hybrid electrodes that integrate TCOs or dielectrics with nanowires, metal grids, or ultrathin metal films. Here, the most relevant transparent electrodes developed to date are introduced, their fundamental properties are described, and their materials are classified according to specific application requirements in high efficiency solar cells and flexible organic light-emitting diodes (OLEDs). This information serves as a guideline for selecting and developing appropriate transparent electrodes according to intended application requirements and functionality.

  19. Optoelectronic Particle-Fallout Sensor

    Science.gov (United States)

    Ihlefeld, Curtis; Mogan, Paul A.; Youngquist, Robert C.; Moerk, John S.; Haskell, William D.; Cox, Robert B.; Rose, Kenneth A.

    1995-01-01

    Portable optoelectronic system monitors fallout of small particles (dust and fibers) onto surface at given location during extended time. Data on accumulated fallout downloaded from system to computer for display and analysis. Typical display is plot of signal proportional to amount of accumulated fallout as function of time and read to determine when contamination occurs. In many cases, possible to establish correlations between accumulations of particles and activities in vicinity. Also capable of signaling alarm in event contamination by fallout exceeds specified level. System made very inexpensively and used to monitor accumulation of dust and fibers associated with motion of air in variety of environments. Phenomena monitored indirectly by use of system might include circulation of air in buildings, and human and animal activity. Also serves as auxiliary intrusion monitor (though probably not real-time alarm) in sealed room because motion of intruder inevitably stirs up some dust.

  20. Semiconductor nanowires: optics and optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Agarwal, R. [University of Pennsylvania, Department of Materials Science and Engineering, Philadelphia, PA (United States); Lieber, C.M. [Harvard University, Department of Chemistry and Chemical Biology, and Division of Engineering Applied Sciences, Cambridge, MA (United States)

    2006-11-15

    Single crystalline semiconductor nanowires are being extensively investigated due to their unique electronic and optical properties and their potential use in novel electronic and photonic devices. The unique properties of nanowires arise owing to their anisotropic geometry, large surface to volume ratio, and carrier and photon confinement in two dimensions (1D system). Currently, tremendous efforts are being devoted to rational synthesis of nanowire structures with control over their composition, structure, dopant concentration, characterization, fundamental properties, and assembly into functional devices. In this article we will review the progress made in the area of nanowire optics and optoelectronic devices, including diodes, lasers, detectors, and waveguides, and will outline the general challenges that must be overcome and some potential solutions in order to continue the exponential progress in this exciting area of research. (orig.)

  1. State-of-the-art photodetectors for optoelectronic integration at telecommunication wavelength

    Directory of Open Access Journals (Sweden)

    Eng Png Ching

    2015-01-01

    Full Text Available Photodetectors hold a critical position in optoelectronic integrated circuits, and they convert light into electricity. Over the past decades, high-performance photodetectors (PDs have been aggressively pursued to enable high-speed, large-bandwidth, and low-noise communication applications. Various material systems have been explored and different structures designed to improve photodetection capability as well as compatibility with CMOS circuits. In this paper, we review state-of-theart photodetection technologies in the telecommunications spectrum based on different material systems, including traditional semiconductors such as InGaAs, Si, Ge and HgCdTe, as well as recently developed systems such as low-dimensional materials (e.g. graphene, carbon nanotube, etc. and noble metal plasmons. The corresponding material properties, fundamental mechanisms, fabrication, theoretical modelling and performance of the typical PDs are presented, including the emerging directions and perspectives of the PDs for optoelectronic integration applications are discussed.

  2. Bandwidth Selection for Weighted Kernel Density Estimation

    OpenAIRE

    Wang, Bin; Wang, Xiaofeng

    2007-01-01

    In the this paper, the authors propose to estimate the density of a targeted population with a weighted kernel density estimator (wKDE) based on a weighted sample. Bandwidth selection for wKDE is discussed. Three mean integrated squared error based bandwidth estimators are introduced and their performance is illustrated via Monte Carlo simulation. The least-squares cross-validation method and the adaptive weight kernel density estimator are also studied. The authors also consider the boundary...

  3. Average Bandwidth Allocation Model of WFQ

    Directory of Open Access Journals (Sweden)

    Tomáš Balogh

    2012-01-01

    Full Text Available We present a new iterative method for the calculation of average bandwidth assignment to traffic flows using a WFQ scheduler in IP based NGN networks. The bandwidth assignment calculation is based on the link speed, assigned weights, arrival rate, and average packet length or input rate of the traffic flows. We prove the model outcome with examples and simulation results using NS2 simulator.

  4. Radiation effects in optoelectronic devices. [Review

    Energy Technology Data Exchange (ETDEWEB)

    Barnes, C.E.; Wiczer, J.J.

    1984-05-01

    Purpose of this report is to provide not only a summary of radiation damage studies at Sandia National Laboratories, but also of those in the literature on the components of optoelectronic systems: light emitting diodes (LEDs), laser diodes, photodetectors, optical fibers, and optical isolators. This review of radiation damage in optoelectronic components is structured according to device type. In each section, a brief discussion of those device properties relevant to radiation effects is given.

  5. Optoelectronic characteristics of CuO nanorods

    Science.gov (United States)

    Xie, De-Hua; Wang, Fei-Fei; Lü, Hao; Du, Min-Yong; Xu, Wen-Jie

    2013-05-01

    Optoelectronic characteristics of p-type CuO nanorods, synthesized by a simple hydrothermal method, were investigated at different atmospheres and oxygen pressures. The CuO nanorods have lower resistance in air than in a vacuum, unlike the n-type semiconductors. This is explained in terms of the surface accumulation conduction. Measurements at different oxygen pressures indicate that oxygen has an important effect on the optoelectronic properties of p-type nanomaterials.

  6. Transparent heat-spreader for optoelectronic applications

    Science.gov (United States)

    Minano, Juan Carlos; Benitez, Pablo

    2014-11-04

    An optoelectronic cooling system is equally applicable to an LED collimator or a photovoltaic solar concentrator. A transparent fluid conveys heat from the optoelectronic chip to a hollow cover over the system aperture. The cooling system can keep a solar concentrator chip at the same temperature as found for a one-sun flat-plate solar cell. Natural convection or forced circulation can operate to convey heat from the chip to the cover.

  7. Metamaterial mirrors in optoelectronic devices

    KAUST Repository

    Esfandyarpour, Majid

    2014-06-22

    The phase reversal that occurs when light is reflected from a metallic mirror produces a standing wave with reduced intensity near the reflective surface. This effect is highly undesirable in optoelectronic devices that use metal films as both electrical contacts and optical mirrors, because it dictates a minimum spacing between the metal and the underlying active semiconductor layers, therefore posing a fundamental limit to the overall thickness of the device. Here, we show that this challenge can be circumvented by using a metamaterial mirror whose reflection phase is tunable from that of a perfect electric mirror († = €) to that of a perfect magnetic mirror († = 0). This tunability in reflection phase can also be exploited to optimize the standing wave profile in planar devices to maximize light-matter interaction. Specifically, we show that light absorption and photocurrent generation in a sub-100 nm active semiconductor layer of a model solar cell can be enhanced by ∼20% over a broad spectral band. © 2014 Macmillan Publishers Limited.

  8. Metal oxides for optoelectronic applications

    Science.gov (United States)

    Yu, Xinge; Marks, Tobin J.; Facchetti, Antonio

    2016-04-01

    Metal oxides (MOs) are the most abundant materials in the Earth's crust and are ingredients in traditional ceramics. MO semiconductors are strikingly different from conventional inorganic semiconductors such as silicon and III-V compounds with respect to materials design concepts, electronic structure, charge transport mechanisms, defect states, thin-film processing and optoelectronic properties, thereby enabling both conventional and completely new functions. Recently, remarkable advances in MO semiconductors for electronics have been achieved, including the discovery and characterization of new transparent conducting oxides, realization of p-type along with traditional n-type MO semiconductors for transistors, p-n junctions and complementary circuits, formulations for printing MO electronics and, most importantly, commercialization of amorphous oxide semiconductors for flat panel displays. This Review surveys the uniqueness and universality of MOs versus other unconventional electronic materials in terms of materials chemistry and physics, electronic characteristics, thin-film fabrication strategies and selected applications in thin-film transistors, solar cells, diodes and memories.

  9. Investigation, study and practice of optoelectronic MOOCs

    Science.gov (United States)

    Shi, Jianhua; Liu, Wei; Lei, Bing; Yao, Tianfu; Fu, Sihua

    2017-08-01

    MOOC(Massive Open Online Course) is a new teaching model that has been springing up since 2012. The typical characters are short teaching video, massive learners, flexible place and time to study, etc. Although MOOC is very popular now, opto-electronic MOOCs are not much enough to meet the need of online learners. In this paper, the phylogeny, the current situation and the characters of MOOC were described, the most famous MOOCs' websites, such as Udacity, Coursera, edX, Chinese College MOOC, xuetangx, were introduced, the opto-electronic MOOCs come from these famous MOOCs' website were investigated extensively and studied deeply, the "Application of Opto-electronic Technology MOOC" which was established by our group is introduced, and some conclusions are obtained. These conclusions can give some suggestions to the online learners who are interested in opto-electronic and the teachers who are teaching the opto-electronic curriculums. The preparation of "Opto-electronic Technology MOOC" is described in short.

  10. Negative inductance circuits for metamaterial bandwidth enhancement

    Science.gov (United States)

    Avignon-Meseldzija, Emilie; Lepetit, Thomas; Ferreira, Pietro Maris; Boust, Fabrice

    2017-12-01

    Passive metamaterials have yet to be translated into applications on a large scale due in large part to their limited bandwidth. To overcome this limitation many authors have suggested coupling metamaterials to non-Foster circuits. However, up to now, the number of convincing demonstrations based on non-Foster metamaterials has been very limited. This paper intends to clarify why progress has been so slow, i.e., the fundamental difficulty in making a truly broadband and efficient non-Foster metamaterial. To this end, we consider two families of metamaterials, namely Artificial Magnetic Media and Artificial Magnetic Conductors. In both cases, it turns out that bandwidth enhancement requires negative inductance with almost zero resistance. To estimate bandwidth enhancement with actual non-Foster circuits, we consider two classes of such circuits, namely Linvill and gyrator. The issue of stability being critical, both metamaterial families are studied with equivalent circuits that include advanced models of these non-Foster circuits. Conclusions are different for Artificial Magnetic Media coupled to Linvill circuits and Artificial Magnetic Conductors coupled to gyrator circuits. In the first case, requirements for bandwidth enhancement and stability are very hard to meet simultaneously whereas, in the second case, an adjustment of the transistor gain does significantly increase bandwidth.

  11. Negative inductance circuits for metamaterial bandwidth enhancement

    Directory of Open Access Journals (Sweden)

    Avignon-Meseldzija Emilie

    2017-01-01

    Full Text Available Passive metamaterials have yet to be translated into applications on a large scale due in large part to their limited bandwidth. To overcome this limitation many authors have suggested coupling metamaterials to non-Foster circuits. However, up to now, the number of convincing demonstrations based on non-Foster metamaterials has been very limited. This paper intends to clarify why progress has been so slow, i.e., the fundamental difficulty in making a truly broadband and efficient non-Foster metamaterial. To this end, we consider two families of metamaterials, namely Artificial Magnetic Media and Artificial Magnetic Conductors. In both cases, it turns out that bandwidth enhancement requires negative inductance with almost zero resistance. To estimate bandwidth enhancement with actual non-Foster circuits, we consider two classes of such circuits, namely Linvill and gyrator. The issue of stability being critical, both metamaterial families are studied with equivalent circuits that include advanced models of these non-Foster circuits. Conclusions are different for Artificial Magnetic Media coupled to Linvill circuits and Artificial Magnetic Conductors coupled to gyrator circuits. In the first case, requirements for bandwidth enhancement and stability are very hard to meet simultaneously whereas, in the second case, an adjustment of the transistor gain does significantly increase bandwidth.

  12. A Bandwidth Reconfigurable Antenna for Cognitive Radios

    Science.gov (United States)

    Ghanem, F.; Hall, P. S.

    Cognitive radios have two operating modes, the searching mode where the system looks for the bandwidth to operate in and the operating mode where users transmit and receive information data through this bandwidth. In the first mode, one may have a very wide bandwidth antenna to be able to scan all the spectrum and in the operating mode one may have a narrow bandwidth antenna to filter out unwanted signals. In this chapter, we present a new antenna capable of operating in both UWB and narrowband modes, which is also tunable in the operating (narrowband) mode. It is composed of a microstrip disc monopole with defect slots in its ground plane. When the slots are deactivated, the antenna exhibits UWB behaviour from 2 to 10 GHz. To narrow the frequency bandwidth, defect slots are activated to act as a band-pass filter that narrows the antenna response. The activation and deactivation of the slots can be achieved by using switches located under the antenna feed line. In this case, the antenna response can be tuned by varying the slots' length. To examine the presented approach, both simulated and measured results are presented and discussed.

  13. Adaptable bandwidth planning using reinforcement learning

    Directory of Open Access Journals (Sweden)

    Dirk Hetzer

    2006-08-01

    Full Text Available In order to improve the bandwidth allocation considering feedback of operational environment, adaptable bandwidth planning based on reinforcement learning is proposed. The approach is based on new constrained scheduling algorithms controlled by reinforcement learning techniques. Different constrained scheduling algorithms,, such as "conflict free scheduling with minimum duration", "partial displacement" and "pattern oriented scheduling" are defined and implemented. The scheduling algorithms are integrated into reinforcement learning strategies. These strategies include: - Q-learning for selection of optimal planning schedule using Q-values; - Informed Q-learning for exploitation and handling of prior-knowledge (patterns of network behaviour; - Relational Q-learning for improving of bandwidth allocation policies dynamically in operational networks considering actual network performance data. Scenarios based on integration of the scheduling algorithms and reinforcement learning techniques in the experimental monitoring and bandwidth planning system called QORE (QoS and resource optimisation are given. The proposed adaptable bandwidth planning is required for more efficient usage of network resources.

  14. Optoelectronic microdevices for combined phototherapy

    Science.gov (United States)

    Zharov, Vladimir P.; Menyaev, Yulian A.; Hamaev, V. A.; Antropov, G. M.; Waner, Milton

    2000-03-01

    In photomedicine in some of cases radiation delivery to local zones through optical fibers can be changed for the direct placing of tiny optical sources like semiconductor microlasers or light diodes in required zones of ears, nostrils, larynx, nasopharynx cochlea or alimentary tract. Our study accentuates the creation of optoelectronic microdevices for local phototherapy and functional imaging by using reflected light. Phototherapeutic micromodule consist of the light source, microprocessor and miniature optics with different kind of power supply: from autonomous with built-in batteries to remote supply by using pulsed magnetic field and supersmall coils. The developed prototype photomodule has size (phi) 8X16 mm and work duration with built-in battery and light diode up several hours at the average power from several tenths of mW to few mW. Preliminary clinical tests developed physiotherapeutic micrimodules in stomatology for treating the inflammation and in otolaryngology for treating tonsillitis and otitis are presented. The developed implanted electro- optical sources with typical size (phi) 4X0,8 mm and with remote supply were used for optical stimulation of photosensitive retina structure and electrostimulation of visual nerve. In this scheme the superminiature coil with 30 electrical integrated levels was used. Such devices were implanted in eyes of 175 patients with different vision problems during clinical trials in Institute of Eye's Surgery in Moscow. For functional imaging of skin layered structure LED arrays coupled photodiodes arrays were developed. The possibilities of this device for study drug diffusion and visualization small veins are discussed.

  15. Teleoperation over low bandwidth communication links

    International Nuclear Information System (INIS)

    Fryer, R.J.; Mair, G.M.; Clark, N.; Heng, J.

    1996-01-01

    Teleoperation is well established for many areas of hazardous environment working. Where such environments are well structured and contained, such as within a working plant, communications bandwidths need not be a constraining factor. However where the worksite is remote, large, poorly structured or damaged communications rapidly become a critical factor in the efficient deployment and use of teleoperation equipment. The paper justifies and describes means which we are exploring to reduce the required communications bandwidth for teleoperation whist retaining full functionality. Techniques involved include incorporation of local intelligence at the worksite, with bandwidth devoted to high-level up-link control signals and down-link feedback, and the use of highly compressed video feeding 'virtual reality type' HMDs to provide maximum system transparency for the operator. The work is drawing on previous experience with an 'anthropomorphic robot heat' for telepresence work, and proprietary algorithms capable of compressing full colour video to standard telephone modem data rates. (Author)

  16. Bandwidth Assessment for MultiRotor UAVs

    Directory of Open Access Journals (Sweden)

    Ferrarese Gastone

    2017-06-01

    Full Text Available This paper is a technical note about the theoretical evaluation of the bandwidth of multirotor helicopters. Starting from a mathematical linear model of the dynamics of a multirotor aircraft, the transfer functions of the state variables that deeply affect the stability characteristics of the aircraft are obtained. From these transfer functions, the frequency response analysis of the system is effected. After this analysis, the bandwidth of the system is defined. This result is immediately utilized for the design of discrete PID controllers for hovering flight stabilization. Numeric simulations are shown to demonstrate that the knowledge of the bandwidth is a valid aid in the design of flight control systems of these machines.

  17. Improved space bandwidth product in image upconversion

    DEFF Research Database (Denmark)

    Dam, Jeppe Seidelin; Pedersen, Christian; Tidemand-Lichtenberg, Peter

    2012-01-01

    We present a technique increasing the space bandwidth product of a nonlinear image upconversion process used for spectral imaging. The technique exploits the strong dependency of the phase-matching condition in sum frequency generation (SFG) on the angle of propagation of the interacting fields...... with respect to the optical axis. Appropriate scanning of the phase-match condition (Δk=0) while acquiring images, allow us to perform monochromatic image reconstruction with a significantly increased space bandwidth product. We derive the theory for the image reconstruction process and demonstrate acquisition...... of images with >10 fold increase in space bandwidth product, i.e. the number of pixel elements, when compared to upconversion of images using fixed phase-match conditions....

  18. Bandwidth extension of speech using perceptual criteria

    CERN Document Server

    Berisha, Visar; Liss, Julie

    2013-01-01

    Bandwidth extension of speech is used in the International Telecommunication Union G.729.1 standard in which the narrowband bitstream is combined with quantized high-band parameters. Although this system produces high-quality wideband speech, the additional bits used to represent the high band can be further reduced. In addition to the algorithm used in the G.729.1 standard, bandwidth extension methods based on spectrum prediction have also been proposed. Although these algorithms do not require additional bits, they perform poorly when the correlation between the low and the high band is weak. In this book, two wideband speech coding algorithms that rely on bandwidth extension are developed. The algorithms operate as wrappers around existing narrowband compression schemes. More specifically, in these algorithms, the low band is encoded using an existing toll-quality narrowband system, whereas the high band is generated using the proposed extension techniques. The first method relies only on transmitted high-...

  19. Effective masking bandwidths at low frequencies.

    Science.gov (United States)

    Fidell, S; Horonjeff, R; Teffeteller, S; Green, D M

    1983-02-01

    Masking of low-frequency sinusoids of varying durations by Gaussian noise of varying spectral shape was measured in three different studies. Common solutions to technical problems associated with control and specification of low-frequency signals were used in the three studies. If interpreted in terms of Fletcher's critical ratio assumptions, data from the first study lead to the inference that the masking bandwidth is inversely related to signal frequency below about 200 Hz. Data from the second study rule out the likelihood that the apparent increase in masking bandwidth is attributable to changes in auditory integration times at low frequencies. The data of the third study suggest that the apparent increase in auditory filter bandwidth at low frequencies is more adequately explained by a decrease in observers' detection efficiency than by broadening of the filter bandpass.

  20. The information bandwidth of neutron scattering instruments

    International Nuclear Information System (INIS)

    Johnson, M.W.

    1995-07-01

    The concept of the information content of a scientific measurement is introduced, and a theory is presented which enables the information that may be obtained by a neutron scattering instrument to be calculated. When combined with the time taken to perform the measurement the bandwidth of the instrument is obtained. This bandwidth is effectively a figure of merit which is of use in three respects: in the design of neutron instrumentation, the optimisation of measurements, and in the comparison of one instrument with another. (author)

  1. Advanced high-bandwidth optical fuzing technology

    Science.gov (United States)

    Liu, Jony J.; von der Lippe, Christian M.

    2005-10-01

    A robust and compact photonic proximity sensor is developed for optical fuze in munitions applications. The design of the optical fuze employed advanced optoelectronic technologies including high-power vertical-cavity surface-emitting lasers (VCSELs), the p-i-n or metal-semiconductor-metal (MSM) photodetectors, SiGe ASIC driver, and miniature optics. The development combines pioneering work and unique expertise at ARDEC, ARL, and Sandia National Laboratories and synergizes the key optoelectronic technologies in components and system designs. This compact sensor will replace conventional costly assemblies based on discrete lasers, photodetectors, and bulky optics and provide a new capability for direct fire applications. It will be mass manufacturable in low cost and simplicity. In addition to the specific applications for gun-fired munitions, numerous civilian uses can be realized by this proximity sensor in automotive, robotics, and aerospace applications. This technology is also applicable to robotic ladar and short-range 3-D imaging.

  2. Epidermal Inorganic Optoelectronics for Blood Oxygen Measurement.

    Science.gov (United States)

    Li, Haicheng; Xu, Yun; Li, Xiaomin; Chen, Ying; Jiang, Yu; Zhang, Changxing; Lu, Bingwei; Wang, Jian; Ma, Yinji; Chen, Yihao; Huang, Yin; Ding, Minquang; Su, Honghong; Song, Guofeng; Luo, Yi; Feng, X

    2017-05-01

    Flexible and stretchable optoelectronics, built-in inorganic semiconductor materials, offer a wide range of unprecedented opportunities and will redefine the conventional rigid optoelectronics in biological application and medical measurement. However, a significant bottleneck lies in the brittleness nature of rigid semiconductor materials and the performance's extreme sensitivity to the light intensity variation due to human skin deformation while measuring physical parameters. In this study, the authors demonstrate a systematic strategy to design an epidermal inorganic optoelectronic device by using specific strain-isolation design, nanodiamond thinning, and hybrid transfer printing. The authors propose all-in-one suspension structure to achieve the stretchability and conformability for surrounding environment, and they propose a two-step transfer printing method for hybrid integrating III-V group emitting elements, Si-based photodetector, and interconnects. Owing to the excellent flexibility and stretchability, such device is totally conformal to skin and keeps the constant light transmission between emitting element and photodetector as well as the signal stability due to skin deformation. This method opens a route for traditional inorganic optoelectronics to achieve flexibility and stretchability and improve the performance of optoelectronics for biomedical application. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  3. Contemporary optoelectronics materials, metamaterials and device applications

    CERN Document Server

    Sukhoivanov, Igor

    2016-01-01

    This book presents a collection of extended contributions on the physics and application of optoelectronic materials and metamaterials.   The book is divided into three parts, respectively covering materials, metamaterials and optoelectronic devices.  Individual chapters cover topics including phonon-polariton interaction, semiconductor and nonlinear organic materials, metallic, dielectric and gyrotropic metamaterials, singular optics, parity-time symmetry, nonlinear plasmonics, microstructured optical fibers, passive nonlinear shaping of ultrashort pulses, and pulse-preserving supercontinuum generation. The book contains both experimental and theoretical studies, and each contribution is a self-contained exposition of a particular topic, featuring an extensive reference list.  The book will be a useful resource for graduate and postgraduate students, researchers and engineers involved in optoelectronics/photonics, quantum electronics, optics, and adjacent areas of science and technology.

  4. Optoelectronic lessons as an interdisciplinary lecture

    Science.gov (United States)

    Wu, Dan; Wu, Maocheng; Gu, Jihua

    2017-08-01

    It is noticed that more and more students in college are passionately curious about the optoelectronic technology, since optoelectronic technology has advanced extremely quickly during the last five years and its applications could be found in a lot of domains. The students who are interested in this area may have different educational backgrounds and their majors cover science, engineering, literature and social science, etc. Our course "History of the Optoelectronic Technology" is set up as an interdisciplinary lecture of the "liberal education" at our university, and is available for all students with different academic backgrounds from any departments of our university. The main purpose of the course is to show the interesting and colorful historical aspects of the development of this technology, so that the students from different departments could absorb the academic nourishment they wanted. There are little complex derivations of physical formulas through the whole lecture, but there are still some difficulties about the lecture which is discussed in this paper.

  5. Perovskite Materials: Solar Cell and Optoelectronic Applications

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Bin [ORNL; Geohegan, David B [ORNL; Xiao, Kai [ORNL

    2017-01-01

    Hybrid organometallic trihalide perovskites are promising candidates in the applications for next-generation, high-performance, low-cost optoelectronic devices, including photovoltaics, light emitting diodes, and photodetectors. Particularly, the solar cells based on this type of materials have reached 22% lab scale power conversion efficiency in only about seven years, comparable to the other thin film photovoltaic technologies. Hybrid perovskite materials not only exhibit superior optoelectronic properties, but also show many interesting physical properties such as ion migration and defect physics, which may allow the exploration of more device functionalities. In this article, the fundamental understanding of the interrelationships between crystal structure, electronic structure, and material properties is discussed. Various chemical synthesis and processing methods for superior device performance in solar cells and optoelectronic devices are reviewed.

  6. 3 Approaches to Achieve Bandwidth Capacity

    Indian Academy of Sciences (India)

    Install new fiber. Average cost $70,000 per mile. Right of way. Higher bandwidth on SONET/TDM. Single mode fiber high dispersion rate. NZDSF cost some 50 percent more than SMF. DWDM. Multi Wavelength Switching, Multiple Interface ATM,Ethernet, Frame Relay, TDM/SONET; Fast, Simple, Cheap.

  7. Experiences in Traceroute and Bandwidth Change Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Logg, C

    2004-06-23

    SLAC has been studying end-to-end WAN bandwidth availability and achievability for 2.5 years via IEPM-BW [1]. IEPM-BW performs network intensive tests every 90 minutes. Based on that experience we have also developed a light weight available bandwidth (ABwE [2]) measurement tool that can make a measurement within a second. We are now extending this to a WAN measurement and detection system (IEPM-LITE) aimed at more quickly detecting and troubleshooting network performance problems and also to be more friendly on lower performance paths. IEPM-LITE uses ping, forward traceroutes, and ABwE sensors to monitor, in close to real-time, Round Trip Times (RTT), changes in available bandwidth and routes to and from target hosts. This paper discusses the experiences, techniques and algorithms used to detect and report on significant traceroute and bandwidth changes. The ultimate aim is to develop a lightweight WAN network performance monitoring system that can detect, in near real time, significant changes and generate alerts.

  8. Experiences in Traceroute and Bandwidth Change Analysis

    International Nuclear Information System (INIS)

    Logg, C

    2004-01-01

    SLAC has been studying end-to-end WAN bandwidth availability and achievability for 2.5 years via IEPM-BW [1]. IEPM-BW performs network intensive tests every 90 minutes. Based on that experience we have also developed a light weight available bandwidth (ABwE [2]) measurement tool that can make a measurement within a second. We are now extending this to a WAN measurement and detection system (IEPM-LITE) aimed at more quickly detecting and troubleshooting network performance problems and also to be more friendly on lower performance paths. IEPM-LITE uses ping, forward traceroutes, and ABwE sensors to monitor, in close to real-time, Round Trip Times (RTT), changes in available bandwidth and routes to and from target hosts. This paper discusses the experiences, techniques and algorithms used to detect and report on significant traceroute and bandwidth changes. The ultimate aim is to develop a lightweight WAN network performance monitoring system that can detect, in near real time, significant changes and generate alerts

  9. Big Bandwidth Battle: Universal ADSL Looks Ahead.

    Science.gov (United States)

    Hargadon, Tom

    1998-01-01

    Discusses the new Universal ADSL (Asymmetric Digital Subscriber Line) standard, which promises simple, high-bandwidth access over standard telephone lines. Topics include varieties of DSL; voice and data capacities; adapters and installation for personal computers; Internet backbone capacity; and headend access. (LRW)

  10. Dependency of human neck reflex responses on the bandwidth of pseudorandom anterior-posterior torso perturbations.

    Science.gov (United States)

    Forbes, Patrick A; de Bruijn, Edo; Schouten, Alfred C; van der Helm, Frans C T; Happee, Riender

    2013-04-01

    The vestibulocollic (VCR) and cervicocollic (CCR) reflexes are essential to stabilize the head-neck system and to deal with unexpected disturbances. This study investigates how neck reflexes contribute to stabilization and modulate with perturbation properties. We hypothesized that VCR and CCR modulate with the bandwidth of the perturbation and that this modulation is maintained across amplitudes and influenced by the eyes being open or closed. Seated subjects were perturbed in an anterior-posterior direction. The perturbations varied in bandwidth from 0.3 Hz to a maximum of 1.2, 2.0, 4.0, and 8.0 Hz, at three amplitudes, and with eyes open and closed. Frequency response functions of head kinematics and neck muscle EMG demonstrated substantial changes with bandwidth and vision and minor changes with amplitude, which through closed-loop identification were attributed to neural (reflexive) modulation. Results suggest that both reflexes were attenuated when perturbations exceeded the system's natural frequency, thereby shifting from a head-in-space to a head-on-trunk stabilization tendency. Additionally, results indicate that reflexive and mechanical stiffness marginally exceed the negative stiffness due to gravity; a stabilization strategy which minimizes effort. With eyes closed, reflexes were attenuated further, presumably due to a reduced ability to discriminate self-motion, driving the system to a head-on-trunk stabilization strategy at the highest bandwidth. We conclude that VCR and CCR modulate with perturbation bandwidth and visual feedback conditions to maintain head-upright posture, but are invariant across amplitude changes.

  11. Energy conversion efficiency in nanotube optoelectronics.

    Energy Technology Data Exchange (ETDEWEB)

    Leonard, Francois Leonard; Stewart, Derek A.

    2004-09-01

    We present theoretical performance estimates for nanotube optoelectronic devices under bias. Current-voltage characteristics of illuminated nanotube p-n junctions are calculated using a self-consistent nonequilibrium Green's function approach. Energy conversion rates reaching tens of percent are predicted for incident photon energies near the band gap energy. In addition, the energy conversion rate increases as the diameter of the nanotube is reduced, even though the quantum efficiency shows little dependence on nanotube radius. These results indicate that the quantum efficiency is not a limiting factor for use of nanotubes in optoelectronics.

  12. Laser applications in the electronics and optoelectronics industry in Japan

    Science.gov (United States)

    Washio, Kunihiko

    1999-07-01

    This paper explains current status and technological trends in laser materials processing applications in electronics and optoelectronics industry in Japan. Various laser equipment based on solid state lasers or gas lasers such as excimer lasers or CO2 lasers has been developed and applied in manufacturing electronic and optoelectronic devices to meet the strong demands for advanced device manufacturing technologies for high-performance, lightweight, low power-consumption portable digital electronic appliances, cellular mobile phones, personal computers, etc. Representative applications of solid-state lasers are, opaque and clear defects repairing of photomasks for LSIs and LCDs, trimming of thick-film chip resistors and low resistance metal resistors, laser cutting and drilling of thin films for high-pin count semiconductor CSP packages, laser patterning of thin-film amorphous silicon solar cells, and laser welding of electronic components such as hard-disk head suspensions, optical modules, miniature relays and lithium ion batteries. Compact and highly efficient diode- pumped and Q-switched solid-state lasers in second or third harmonic operation mode are now being increasingly incorporated in various laser equipment for fine material processing. Representative applications of excimer lasers are, sub-quarter micron design-rule LSI lithography and low- temperature annealing of poly-silicon TFT LCD.

  13. Flexible power and bandwidth allocation in mobile satellites

    Science.gov (United States)

    Keyes, L. A.

    The introduction of L-band mobile communication services by spot beam satellites creates a payload design challenge due to uncertainty in the location and size of the new market to be served. A combination of payload technologies that allow a flexible allocation of power and bandwidth to any portion of the coverage area is described. Power flexibility is achieved by a novel combination of a low-level beam-forming network and a matrix power module which ensures equal sharing of power among individual amplifiers. This eliminates the loss of efficiency and increased mass when an amplifier associated with a beam must be over-designed to meet uncertainties in power distribution between beams. Flexibility in allocation of bandwidth to beams is achieved by intermediate frequency subdivision of the L-band service categories defined by ITU. These spectral subdivisions are assigned to beams by an IF interconnect matrix having beam ports and filter ports as inputs and outputs, respectively. Two such filter switch matrices are required, one for the inbound L-band to feeder link transponder, and one for the outbound feeder link to L-band transponder.

  14. Optoelectronic line transmission an introduction to fibre optics

    CERN Document Server

    Tricker, Raymond L

    2013-01-01

    Optoelectronic Line Transmission: An Introduction to Fibre Optics presents a basic introduction as well as a background reference manual on fiber optic transmission. The book discusses the basic principles of optical line transmission; the advantages and disadvantages of optical fibers and optoelectronic signalling; the practical applications of optoelectronics; and the future of optoelectronics. The text also describes the theories of optical line transmission; fibers and cables for optical transmission; transmitters including light-emitting diodes and lasers; and receivers including photodi

  15. Functionalized polyfluorenes for use in optoelectronic devices

    Science.gov (United States)

    Chichak, Kelly Scott [Clifton Park, NY; Lewis, Larry Neil [Scotia, NY; Cella, James Anthony [Clifton Park, NY; Shiang, Joseph John [Niskayuna, NY

    2011-11-01

    The present invention relates to process comprising reacting a polyfluorenes comprising at least one structural group of formula I ##STR00001## with an iridium (III) compound of formula II ##STR00002## The invention also relates to the polyfluorenes, which are products of the reaction, and the use of the polyfluorenes in optoelectronic devices.

  16. High-performance optoelectronic bus system

    Science.gov (United States)

    Fa, Jinghuai; Zhao, Chunhe; Liu, Jian; Chen, Ray T.

    1998-05-01

    In order to utilize the high speed of optical interconnects and overcome the latencyproblem of a large bus structure, we proposed an architecture of optoelectronic hierarchical bus system. Waveguide hologram implementations, and its associated cache coherence problem are addressed. In our configuration, bus hierarchy is controlled with electronic programmable plates. Optical signals can be transmitted on all-optical paths without intermediate conversions.

  17. Fast Feature-Recognizing Optoelectronic System

    Science.gov (United States)

    Thakoor, S.; Thakoor, A. P.

    1990-01-01

    Proposed optoelectronic system recognizes features or classifies images by processing outputs of photosensors rapidly, in parallel, through circuits developed in research on neural networks. Array of photoconductive elements serve as photomodulated connections in electronic neural network, which provides high speed data compression to generate feature vector. System able to "learn" new patterns for subsequent recognition. Potential applications in robotic vision systems and pattern recognition.

  18. Monocrystalline halide perovskite nanostructures : For optoelectronic applications

    NARCIS (Netherlands)

    Khoram, P.

    2018-01-01

    Halide perovskites are a promising class of materials for incorporation in optoelectronics with higher efficiency and lower cost. The solution processability of these materials provides unique opportunities for simple nanostructure fabrication. In the first half of the thesis (chapter 2 and 3) we

  19. Optoelectronics technologies for Virtual Reality systems

    Science.gov (United States)

    Piszczek, Marek; Maciejewski, Marcin; Pomianek, Mateusz; Szustakowski, Mieczysław

    2017-08-01

    Solutions in the field of virtual reality are very strongly associated with optoelectronic technologies. This applies to both process design and operation of VR applications. Technologies such as 360 cameras and 3D scanners significantly improve the design work. What is more, HMD displays with high field of view or optoelectronic Motion Capture systems and 3D cameras guarantee an extraordinary experience in immersive VR applications. This article reviews selected technologies from the perspective of their use in a broadly defined process of creating and implementing solutions for virtual reality. There is also the ability to create, modify and adapt new approaches that show team own work (SteamVR tracker). Most of the introduced examples are effectively used by authors to create different VR applications. The use of optoelectronic technology in virtual reality is presented in terms of design and operation of the system as well as referring to specific applications. Designers and users of VR systems should take a close look on new optoelectronics solutions, as they can significantly contribute to increased work efficiency and offer completely new opportunities for virtual world reception.

  20. Visual and opto-electronic autocollimator

    Directory of Open Access Journals (Sweden)

    Fesenko A .V.

    2012-12-01

    Full Text Available The article presents advantages of optical-electronic autocollimator to the visual ones. The possibility is shown to upgrade existing visual systems by replacing the autocollimating eyepieces by the units containing multielement detectors and connecting them to the computer. The brief characteristics of autocollimating eyepieces and modern optoelectronic autocollimators are given.

  1. Photoemission from optoelectronic materials and their nanostructures

    CERN Document Server

    Ghatak, Kamakhya Prasad; Bhattacharya, Sitangshu

    2009-01-01

    This monograph investigates photoemission from optoelectronic materials and their nanostructures. It contains open-ended research problems which form an integral part of the text and are useful for graduate courses as well as aspiring Ph.D.'s and researchers..

  2. Nano crystals for Electronic and Optoelectronic Applications

    International Nuclear Information System (INIS)

    Zhu, T.; Cloutier, S.G.; Ivanov, I; Knappenberger Jr, K.L.; Robel, I.; Zhang, F

    2012-01-01

    Electronic and optoelectronic devices, from computers and smart cell phones to solar cells, have become a part of our life. Currently, devices with featured circuits of 45 nm in size can be fabricated for commercial use. However, further development based on traditional semiconductor is hindered by the increasing thermal issues and the manufacturing cost. During the last decade, nano crystals have been widely adopted in various electronic and optoelectronic applications. They provide alternative options in terms of ease of processing, low cost, better flexibility, and superior electronic/optoelectronic properties. By taking advantage of solution-processing, self-assembly, and surface engineering, nano crystals could serve as new building blocks for low-cost manufacturing of flexible and large area devices. Tunable electronic structures combined with small exciton binding energy, high luminescence efficiency, and low thermal conductivity make nano crystals extremely attractive for FET, memory device, solar cell, solid-state lighting/display, photodetector, and lasing applications. Efforts to harness the nano crystal quantum tunability have led to the successful demonstration of many prototype devices, raising the public awareness to the wide range of solutions that nano technology can provide for an efficient energy economy. This special issue aims to provide the readers with the latest achievements of nano crystals in electronic and optoelectronic applications, including the synthesis and engineering of nano crystals towards the applications and the corresponding device fabrication, characterization and computer modeling.

  3. Digital demodulator for wide bandwidth SAR

    DEFF Research Database (Denmark)

    Jørgensen, Jørn Hjelm

    2000-01-01

    A novel approach to the design of efficient digital quadrature demodulators for wide bandwidth SAR systems is described. Efficiency is obtained by setting the intermediate frequency to 1/4 the ADC sampling frequency. One channel is made filter-free by synchronizing the local oscillator with the o......A novel approach to the design of efficient digital quadrature demodulators for wide bandwidth SAR systems is described. Efficiency is obtained by setting the intermediate frequency to 1/4 the ADC sampling frequency. One channel is made filter-free by synchronizing the local oscillator...... with the output decimator. The filter required by the other channel is optimized through global search using the system level performance metrics integrated sidelobe level ratio (ISLR) and peak sidelobe level ratio (PSLR)....

  4. Bandwidth Analysis of Smart Meter Network Infrastructure

    DEFF Research Database (Denmark)

    Balachandran, Kardi; Olsen, Rasmus Løvenstein; Pedersen, Jens Myrup

    2014-01-01

    Advanced Metering Infrastructure (AMI) is a net-work infrastructure in Smart Grid, which links the electricity customers to the utility company. This network enables smart services by making it possible for the utility company to get an overview of their customers power consumption and also control...... to utilize smart meters and which existing broadband network technologies can facilitate this smart meter service. Initially, scenarios for smart meter infrastructure are identified. The paper defines abstraction models which cover the AMI scenarios. When the scenario has been identified a general overview...... of the bandwidth requirements are analysed. For this analysis the assumptions and limitations are defined. The results obtained by the analysis show, that the amount of data collected and transferred by a smart meter is very low compared to the available bandwidth of most internet connections. The results show...

  5. Large-bandwidth planar photonic crystal waveguides

    DEFF Research Database (Denmark)

    Søndergaard, Thomas; Lavrinenko, Andrei

    2002-01-01

    A general design principle is presented for making finite-height photonic crystal waveguides that support leakage-free guidance of light over large frequency intervals. The large bandwidth waveguides are designed by introducing line defects in photonic crystal slabs, where the material in the line...... defect has appropriate dispersion properties relative to the photonic crystal slab material surrounding the line defect. A three-dimensional theoretical analysis is given for large-bandwidth waveguide designs based on a silicon-air photonic crystal slab suspended in air. In one example, the leakage......-free single-mode guidance is found for a large frequency interval covering 60% of the photonic band-gap....

  6. High bandwidth concurrent processing on commodity platforms

    CERN Document Server

    Boosten, M; Van der Stok, P D V

    1999-01-01

    The I/O bandwidth and real-time processing power required for high- energy physics experiments is increasing rapidly over time. The current requirements can only be met by using large-scale concurrent processing. We are investigating the use of a large PC cluster interconnected by Fast and Gigabit Ethernet to meet the performance requirements of the ATLAS second level trigger. This architecture is attractive because of its performance and competitive pricing. A major problem is obtaining frequent high-bandwidth I/O without sacrificing the CPU's processing power. We present a tight integration of a user-level scheduler and a zero-copy communication layer. This system closely approaches the performance of the underlying hardware in terms of both CPU power and I/O capacity. (0 refs).

  7. Reconstitution of Low Bandwidth Reaction History

    International Nuclear Information System (INIS)

    May, M.; Clancy, T.; Fittinghoff, D.; Gennaro, P.; Hagans, K.; Halvorson, G.; Lowry, M.; Perry, T.; Roberson, P.; Smith, D.; Teruya, A.; Blair, J.; Davis, B.; Hunt, E.; Emkeit, B.; Galbraith, J.; Kelly, B.; Montoya, R.; Nickel, G.; Ogle, J.; Wilson, K.; Wood, M.

    2004-01-01

    The goal of the Test Readiness Program is to transition to a 24 month test readiness posture and if approved move to an 18-month posture. One of the key components of the Test Readiness Program necessary to meet this goal is the reconstitution of the important diagnostics. Since the end of nuclear testing, the ability to field diagnostics on a nuclear test has deteriorated. Reconstitution of diagnostics before those who had experience in nuclear testing either retire or leave is essential to achieving a shorter test readiness posture. Also, the data recording systems have not been used since the end of testing. This report documents the reconstitution of one vital diagnostic: the low bandwidth reaction history diagnostic for FY04. Reaction history is one of the major diagnostics that has been used on all LLNL and LANL tests since the early days of nuclear testing. Reaction history refers to measuring the time history of the gamma and neutron output from a nuclear test. This gives direct information on the nuclear reactions taking place in the device. The reaction history measurements are one of the prime measurements the nuclear weapon scientists use to validate their models of device performance. All tests currently under consideration require the reaction history diagnostic. Thus moving to a shorter test readiness posture requires the reconstitution of the ability to make reaction history measurements. Reconstitution of reaction history was planned to be in two steps. Reaction history measurements that have been used in the past can be broadly placed into two categories. The most common type of reaction history and the one that has been performed on virtually all nuclear tests is termed low bandwidth reaction history. This measurement has a time response that is limited by the bandpass of kilometer length coaxial cables. When higher bandwidth has been required for specific measurements, fiber optic techniques have been used. This is referred to as high-bandwidth

  8. Time-optimal control with finite bandwidth

    Science.gov (United States)

    Hirose, M.; Cappellaro, P.

    2018-04-01

    Time-optimal control theory provides recipes to achieve quantum operations with high fidelity and speed, as required in quantum technologies such as quantum sensing and computation. While technical advances have achieved the ultrastrong driving regime in many physical systems, these capabilities have yet to be fully exploited for the precise control of quantum systems, as other limitations, such as the generation of higher harmonics or the finite response time of the control apparatus, prevent the implementation of theoretical time-optimal control. Here we present a method to achieve time-optimal control of qubit systems that can take advantage of fast driving beyond the rotating wave approximation. We exploit results from time-optimal control theory to design driving protocols that can be implemented with realistic, finite-bandwidth control fields, and we find a relationship between bandwidth limitations and achievable control fidelity.

  9. Very low bandwidth, unattended imager for surveillance applications

    Energy Technology Data Exchange (ETDEWEB)

    Eichel, P.H.; Jakowatz, C.V. Jr.

    1986-01-01

    The need arises in certain vehicular surveillance applications for an electronic imager that can perform without human interaction and can transmit definitive images over very low bandwidth channels. The investigators have found that line scan imagers offer particular advantages toward these ends. Specifically, the use of a line scan imager facilitates the following processing steps: (1) segmentation of the vehicle from the background, (2) automatic exposure control, (3) light level equalization prior to quantization, and (4) implementation of an adaptive sampling scheme. These processing steps together with the source encoder may be implemented on a relatively low throughput processor and achieve near real time operation. The specific encoding method used here is an extended differential pulse code modulation (DPCM). A prototype system has been developed, producing medium resolution images at less than 10K bits per frame.

  10. Probabilistic Bandwidth Assignment in Wireless Sensor Networks

    OpenAIRE

    Khan , Dawood; Nefzi , Bilel; Santinelli , Luca; Song , Ye-Qiong

    2012-01-01

    International audience; With this paper we offer an insight in designing and analyzing wireless sensor networks in a versatile manner. Our framework applies probabilistic and component-based design principles for the wireless sensor network modeling and consequently analysis; while maintaining flexibility and accuracy. In particular, we address the problem of allocating and reconfiguring the available bandwidth. The framework has been successfully implemented in IEEE 802.15.4 using an Admissi...

  11. Nonlinear Evolution Equations for Broader Bandwidth Wave Packets in Crossing Sea States

    Directory of Open Access Journals (Sweden)

    S. Debsarma

    2014-01-01

    Full Text Available Two coupled nonlinear equations are derived describing the evolution of two broader bandwidth surface gravity wave packets propagating in two different directions in deep water. The equations, being derived for broader bandwidth wave packets, are applicable to more realistic ocean wave spectra in crossing sea states. The two coupled evolution equations derived here have been used to investigate the instability of two uniform wave trains propagating in two different directions. We have shown in figures the behaviour of the growth rate of instability of these uniform wave trains for unidirectional as well as for bidirectional perturbations. The figures drawn here confirm the fact that modulational instability in crossing sea states with broader bandwidth wave packets can lead to the formation of freak waves.

  12. Irradiation of new optoelectronic components for HL-LHC data transmission links

    International Nuclear Information System (INIS)

    Nasr-Storey, S Seif El; Detraz, S; Olantera, L; Sigaud, C; Soos, C; Troska, J; Vasey, F

    2013-01-01

    Candidate optoelectronic components for use in future data-transmission links at the High-Luminosity Large Hadron Collider (HL-LHC) were irradiated with 20 MeV neutrons at the University Cyclotron in Louvain-La-Neuve, Belgium and 24 GeV protons at the CERN PS irradiation facility. The results from this test for multi-channel transmitters, Germanium photodiodes, and Silicon photonics modulators are presented here

  13. Frequency and bandwidth conversion of single photons in a room-temperature diamond quantum memory.

    Science.gov (United States)

    Fisher, Kent A G; England, Duncan G; MacLean, Jean-Philippe W; Bustard, Philip J; Resch, Kevin J; Sussman, Benjamin J

    2016-04-05

    The spectral manipulation of photons is essential for linking components in a quantum network. Large frequency shifts are needed for conversion between optical and telecommunication frequencies, while smaller shifts are useful for frequency-multiplexing quantum systems, in the same way that wavelength division multiplexing is used in classical communications. Here we demonstrate frequency and bandwidth conversion of single photons in a room-temperature diamond quantum memory. Heralded 723.5 nm photons, with 4.1 nm bandwidth, are stored as optical phonons in the diamond via a Raman transition. Upon retrieval from the diamond memory, the spectral shape of the photons is determined by a tunable read pulse through the reverse Raman transition. We report central frequency tunability over 4.2 times the input bandwidth, and bandwidth modulation between 0.5 and 1.9 times the input bandwidth. Our results demonstrate the potential for diamond, and Raman memories in general, as an integrated platform for photon storage and spectral conversion.

  14. Novel secure and bandwidth efficient optical code division multiplexed system for future access networks

    Science.gov (United States)

    Singh, Simranjit

    2016-12-01

    In this paper, a spectrally coded optical code division multiple access (OCDMA) system using a hybrid modulation scheme has been investigated. The idea is to propose an effective approach for simultaneous improvement of the system capacity and security. Data formats, NRZ (non-return to zero), DQPSK (differential quadrature phase shift keying), and PoISk (polarisation shift keying) are used to get the orthogonal modulated signal. It is observed that the proposed hybrid modulation provides efficient utilisation of bandwidth, increases the data capacity and enhances the data confidentiality over existing OCDMA systems. Further, the proposed system performance is compared with the current state-of-the-art OCDMA schemes.

  15. Advanced packaging concepts for low-cost optoelectronic devices

    Science.gov (United States)

    Bernabé, Stéphane

    2006-07-01

    The multiplication of fibre optic networks during the years 1980 to 2000 has led to the development of specific packaging designs for laser modules, e.g. butterfly or TO-can coaxial packages. Since the beginning of years 2000, it has become necessary for packaging designers to deal with new requirements in term of module size, cost, thermal and electrical performances, particularly concerning the HF design. From these new requirements, new quasi-standards have appeared: TO-based TOSAs, XMD, and so on... However, these solutions are still based on traditional technologies : die soldering, 3D active alignment, Kovar packages, laser welding, single-chip devices, discrete micro-optics., unsuitable for mass production at very low cost. Today, the challenge for optoelectronic industry is thus to achieve a mutation of the packaging and assembly concepts, similar to the one the microlelectronic industry has done thirty years ago, by introducing advanced packaging technologies in order to address emerging markets and need, such as FTTx and Very Short Reach optical links, at the targeted costs. This will be also done by pushing ahead the integration of several optical function on the same chip or optical board. Some of these emerging technologies, such as optical MCM (Multi Chip Module), passive alignment, new materials for thermal management, flip-chip hybridisation, are key concepts to manage this next step and are reviewed in this paper. These concepts have already been applied in some industrial products and should spread in the next years.

  16. Low and Expensive Bandwidth Remains Key Bottleneck for ...

    African Journals Online (AJOL)

    These bottlenecks have dwarfed the expectations of the citizens to fully participate in the new world economic order galvanized by e-commerce and world trade. It is estimated that M.I.T in Boston USA has bandwidth allocation that surpasses all the bandwidth allocated to Nigeria put together. Low bandwidth has been found ...

  17. Optoelectronic Devices Advanced Simulation and Analysis

    CERN Document Server

    Piprek, Joachim

    2005-01-01

    Optoelectronic devices transform electrical signals into optical signals and vice versa by utilizing the sophisticated interaction of electrons and light within micro- and nano-scale semiconductor structures. Advanced software tools for design and analysis of such devices have been developed in recent years. However, the large variety of materials, devices, physical mechanisms, and modeling approaches often makes it difficult to select appropriate theoretical models or software packages. This book presents a review of devices and advanced simulation approaches written by leading researchers and software developers. It is intended for scientists and device engineers in optoelectronics, who are interested in using advanced software tools. Each chapter includes the theoretical background as well as practical simulation results that help to better understand internal device physics. The software packages used in the book are available to the public, on a commercial or noncommercial basis, so that the interested r...

  18. Glass-Forming Organic Semiconductors for Optoelectronics

    Directory of Open Access Journals (Sweden)

    Aušra TOMKEVIČIENĖ

    2011-11-01

    Full Text Available Organic electronics and optoelectronics are newly emerging fields of science and technology that cover chemistry, physics, and materials science. Electronic and optoelectronic devices using organic materials are attractive because of the materials characteristics, potentially low cost, and capability of large-area, flexible device fabrication. Such devices as OLEDs, OPVs, and OFETs involve charge transport as a main process in their operation processes, and therefore, require high-performance charge-transporting materials. This review article focuses on charge-transporting materials for use in OLEDs, OPVs, and OFETs. We have tried to arrange the charge-transporting materials in order by classifying them on the basis of their molecular structures. Molecular design concepts for charge-transporting materials and their charge-transport properties are discussed.http://dx.doi.org/10.5755/j01.ms.17.4.767

  19. Multi-material optoelectronic fiber devices

    Science.gov (United States)

    Sorin, F.; Yan, Wei; Volpi, Marco; Page, Alexis G.; Nguyen Dang, Tung; Qu, Y.

    2017-05-01

    The recent ability to integrate materials with different optical and optoelectronic properties in prescribed architectures within flexible fibers is enabling novel opportunities for advanced optical probes, functional surfaces and smart textiles. In particular, the thermal drawing process has known a series of breakthroughs in recent years that have expanded the range of materials and architectures that can be engineered within uniform fibers. Of particular interest in this presentation will be optoelectronic fibers that integrate semiconductors electrically addressed by conducting materials. These long, thin and flexible fibers can intercept optical radiation, localize and inform on a beam direction, detect its wavelength and even harness its energy. They hence constitute ideal candidates for applications such as remote and distributed sensing, large-area optical-detection arrays, energy harvesting and storage, innovative health care solutions, and functional fabrics. To improve performance and device complexity, tremendous progresses have been made in terms of the integrated semiconductor architectures, evolving from large fiber solid-core, to sub-hundred nanometer thin-films, nano-filaments and even nanospheres. To bridge the gap between the optoelectronic fiber concept and practical applications however, we still need to improve device performance and integration. In this presentation we will describe the materials and processing approaches to realize optoelectronic fibers, as well as give a few examples of demonstrated systems for imaging as well as light and chemical sensing. We will then discuss paths towards practical applications focusing on two main points: fiber connectivity, and improving the semiconductor microstructure by developing scalable approaches to make fiber-integrated single-crystal nanowire based devices.

  20. Wireless bandwidth authentication improving quality of service

    OpenAIRE

    Peart, Amanda; Good, Alice

    2012-01-01

    With the popularity of distributed applications such as BitTorrent and Peer 2 Peer (P2P) networks, coupled with the increase in mobility of end user devices, there is a requirement for dynamic bandwidth management. Mobile users require access to the internet at varying times and for various reasons. Generally this access is via public hotspots in places such as airports, hotels and coffee shops. Therefore it is paramount that user access is managed as some users will utilize an unfair amount ...

  1. Exceptional Optoelectronic Properties of Hydrogenated Bilayer Silicene

    Directory of Open Access Journals (Sweden)

    Bing Huang

    2014-05-01

    Full Text Available Silicon is arguably the best electronic material, but it is not a good optoelectronic material. By employing first-principles calculations and the cluster-expansion approach, we discover that hydrogenated bilayer silicene (BS shows promising potential as a new kind of optoelectronic material. Most significantly, hydrogenation converts the intrinsic BS, a strongly indirect semiconductor, into a direct-gap semiconductor with a widely tunable band gap. At low hydrogen concentrations, four ground states of single- and double-sided hydrogenated BS are characterized by dipole-allowed direct (or quasidirect band gaps in the desirable range from 1 to 1.5 eV, suitable for solar applications. At high hydrogen concentrations, three well-ordered double-sided hydrogenated BS structures exhibit direct (or quasidirect band gaps in the color range of red, green, and blue, affording white light-emitting diodes. Our findings open opportunities to search for new silicon-based light-absorption and light-emitting materials for earth-abundant, high-efficiency, optoelectronic applications.

  2. New Development of Membrane Base Optoelectronic Devices

    Directory of Open Access Journals (Sweden)

    Leon Hamui

    2017-12-01

    Full Text Available It is known that one factor that affects the operation of optoelectronic devices is the effective protection of the semiconductor materials against environmental conditions. The permeation of atmospheric oxygen and water molecules into the device structure induces degradation of the electrodes and the semiconductor. As a result, in this communication we report the fabrication of semiconductor membranes consisting of Magnesium Phthalocyanine-allene (MgPc-allene particles dispersed in Nylon 11 films. These membranes combine polymer properties with organic semiconductors properties and also provide a barrier effect for the atmospheric gas molecules. They were prepared by high vacuum evaporation and followed by thermal relaxation technique. For the characterization of the obtained membranes, Fourier-transform infrared spectroscopy (FT-IR, scanning electron microscopy (SEM, and energy dispersive spectroscopy (EDS were used to determine the chemical and microstructural properties. UV-ViS, null ellipsometry, and visible photoluminescence (PL at room temperature were used to characterize the optoelectronic properties. These results were compared with those obtained for the organic semiconductors: MgPc-allene thin films. Additionally, semiconductor membranes devices have been prepared, and a study of the device electronic transport properties was conducted by measuring electrical current density-voltage (J-V characteristics by four point probes with different wavelengths. The resistance properties against different environmental molecules are enhanced, maintaining their semiconductor functionality that makes them candidates for optoelectronic applications.

  3. Optical Near-field Interactions and Forces for Optoelectronic Devices

    Science.gov (United States)

    Kohoutek, John Michael

    Throughout history, as a particle view of the universe began to take shape, scientists began to realize that these particles were attracted to each other and hence came up with theories, both analytical and empirical in nature, to explain their interaction. The interaction pair potential (empirical) and electromagnetics (analytical) theories, both help to explain not only the interaction between the basic constituents of matter, such as atoms and molecules, but also between macroscopic objects, such as two surfaces in close proximity. The electrostatic force, optical force, and Casimir force can be categorized as such forces. A surface plasmon (SP) is a collective motion of electrons generated by light at the interface between two mediums of opposite signs of dielectric susceptibility (e.g. metal and dielectric). Recently, surface plasmon resonance (SPR) has been exploited in many areas through the use of tiny antennas that work on similar principles as radio frequency (RF) antennas in optoelectronic devices. These antennas can produce a very high gradient in the electric field thereby leading to an optical force, similar in concept to the surface forces discussed above. The Atomic Force Microscope (AFM) was introduced in the 1980s at IBM. Here we report on its uses in measuring these aforementioned forces and fields, as well as actively modulating and manipulating multiple optoelectronic devices. We have shown that it is possible to change the far field radiation pattern of an optical antenna-integrated device through modification of the near-field of the device. This modification is possible through change of the local refractive index or reflectivity of the "hot spot" of the device, either mechanically or optically. Finally, we have shown how a mechanically active device can be used to detect light with high gain and low noise at room temperature. It is the aim of several of these integrated and future devices to be used for applications in molecular sensing

  4. Single passband microwave photonic filter with wideband tunability and adjustable bandwidth.

    Science.gov (United States)

    Chen, Tong; Yi, Xiaoke; Li, Liwei; Minasian, Robert

    2012-11-15

    A new and simple structure for a single passband microwave photonic filter is presented. It is based on using an electro-optical phase modulator and a tunable optical filter and only requires a single wavelength source and a single photodetector. Experimental results are presented that demonstrate a single passband, flat-top radio-frequency filter response without free spectral range limitations, along with the capability of tuning the center frequency and filter bandwidth independently.

  5. Effective electro-optical modulation with high extinction ratio by a graphene-silicon microring resonator

    DEFF Research Database (Denmark)

    Ding, Yunhong; Zhu, Xiaolong; Xiao, Sanshui

    2015-01-01

    Graphene opens up for novel optoelectronic applications thanks to its high carrier mobility, ultra-large absorption bandwidth, and extremely fast material response. In particular, the opportunity to control optoelectronic properties through tuning of the Fermi level enables electro-optical modula...... with an extinction ratio of 3.8 dB is successfully demonstrated by applying a square-waveform with a 4 V peak-to-peak voltage....

  6. Filterless low-phase-noise frequency-quadrupled microwave generation based on a multimode optoelectronic oscillator

    Science.gov (United States)

    Teng, Yichao; Zhang, Pin; Zhang, Baofu; Chen, Yiwang

    2018-02-01

    A scheme to realize low-phase-noise frequency-quadrupled microwave generation without any filter is demonstrated. In this scheme, a multimode optoelectronic oscillator is mainly contributed by dual-parallel Mach-Zehnder modulators, fiber, photodetector, and microwave amplifier. The local source signal is modulated by a child MZM (MZMa), which is worked at maximum transmission point. Through properly adjusting the bias voltages of the other child MZM (MZMb) and the parent MZM (MZMc), optical carrier is effectively suppressed and second sidebands are retained, then the survived optical signal is fed back to the photodetector and MZMb to form an optoelectronic hybrid resonator and realize frequency-quadrupled signal generation. Due to the high Q-factor and mode selection effect of the optoelectronic hybrid resonator, compared with the source signal, the generated frequency-quadrupled signal has a lower phase noise. The approach has verified by experiments, and 18, 22, and 26 GHz frequency-quadrupled signal are generated by 4.5, 5.5, and 6.5 GHz local source signals. Compared with 4.5 GHz source signal, the phase noise of generated 18 GHz signal at 10 kHz frequency offset has 26.5 dB reduction.

  7. An integrated and multi-purpose microscope for the characterization of atomically thin optoelectronic devices

    Science.gov (United States)

    De Sanctis, Adolfo; Jones, Gareth F.; Townsend, Nicola J.; Craciun, Monica F.; Russo, Saverio

    2017-05-01

    Optoelectronic devices based on graphene and other two-dimensional (2D) materials, such as transition metal dichalcogenides (TMDs), are the focus of wide research interest. They can be the key to improving bandwidths in telecommunications, capacity in data storage, and new features in consumer electronics, safety devices, and medical equipment. The characterization of these emerging atomically thin materials and devices strongly relies on a set of measurements involving both optical and electronic instrumentation ranging from scanning photocurrent mapping to Raman and photoluminescence (PL) spectroscopy. Furthermore, proof-of-concept devices are usually fabricated from micro-meter size flakes, requiring microscopy techniques to characterize them. Current state-of-the-art commercial instruments offer the ability to characterize individual properties of these materials with no option for the in situ characterization of a wide enough range of complementary optical and electrical properties. Presently, the requirement to switch atomically thin materials from one system to another often radically affects the properties of these uniquely sensitive materials through atmospheric contamination. Here, we present an integrated, multi-purpose instrument dedicated to the optical and electrical characterization of devices based on 2D materials which is able to perform low frequency electrical measurements, scanning photocurrent mapping, and Raman, absorption, and PL spectroscopy in one single setup with full control over the polarization and wavelength of light. We characterize this apparatus by performing multiple measurements on graphene, transition metal dichalcogenides (TMDs), and Si. The performance and resolution of each individual measurement technique is found to be equivalent to that of commercially available instruments. Contrary to nowadays' commercial systems, a significant advantage of the developed instrument is that for the first time the integration of a wide

  8. Optimal filter bandwidth for pulse oximetry

    Science.gov (United States)

    Stuban, Norbert; Niwayama, Masatsugu

    2012-10-01

    Pulse oximeters contain one or more signal filtering stages between the photodiode and microcontroller. These filters are responsible for removing the noise while retaining the useful frequency components of the signal, thus improving the signal-to-noise ratio. The corner frequencies of these filters affect not only the noise level, but also the shape of the pulse signal. Narrow filter bandwidth effectively suppresses the noise; however, at the same time, it distorts the useful signal components by decreasing the harmonic content. In this paper, we investigated the influence of the filter bandwidth on the accuracy of pulse oximeters. We used a pulse oximeter tester device to produce stable, repetitive pulse waves with digitally adjustable R ratio and heart rate. We built a pulse oximeter and attached it to the tester device. The pulse oximeter digitized the current of its photodiode directly, without any analog signal conditioning. We varied the corner frequency of the low-pass filter in the pulse oximeter in the range of 0.66-15 Hz by software. For the tester device, the R ratio was set to R = 1.00, and the R ratio deviation measured by the pulse oximeter was monitored as a function of the corner frequency of the low-pass filter. The results revealed that lowering the corner frequency of the low-pass filter did not decrease the accuracy of the oxygen level measurements. The lowest possible value of the corner frequency of the low-pass filter is the fundamental frequency of the pulse signal. We concluded that the harmonics of the pulse signal do not contribute to the accuracy of pulse oximetry. The results achieved by the pulse oximeter tester were verified by human experiments, performed on five healthy subjects. The results of the human measurements confirmed that filtering out the harmonics of the pulse signal does not degrade the accuracy of pulse oximetry.

  9. Optoelectronic Device and System Development for Imaging Through Turbulence

    National Research Council Canada - National Science Library

    Fainman, Y

    1998-01-01

    Identified a candidate algorithm suitable for imaging through turbulence. The phase diversity algorithm demonstrate good performance mapped the phase diversity algorithms onto an opto-electronic (OE) architecture...

  10. Graphene optoelectronics synthesis, characterization, properties, and applications

    CERN Document Server

    bin M Yusoff, Abdul Rashid

    2014-01-01

    This first book on emerging applications for this innovative material gives an up-to-date account of the many opportunities graphene offers high-end optoelectronics.The text focuses on potential as well as already realized applications, discussing metallic and passive components, such as transparent conductors and smart windows, as well as high-frequency devices, spintronics, photonics, and terahertz devices. Also included are sections on the fundamental properties, synthesis, and characterization of graphene. With its unique coverage, this book will be welcomed by materials scientists, solid-

  11. Performance Evaluation of an Integrated Optoelectronic Receiver

    OpenAIRE

    A. Vera-Marquina; J. Martínez-Castillo; I.E. Zaldivar-Huerta; A. Díaz-Sanchez

    2014-01-01

    This work describes the optical and electrical characterization of an integrated optoelectronic receiver. The receiver is composed of a photodiode and a transimpedance amplifier, both fabricated in silicon technology using a 0.8 μm BiCMOS process. The total area occupied by the photodiode is of 10,000 μm2. In a first step, the generated photocurrent of the photodiode is measured for the wavelengths of 780 nm and 830 nm at different levels of optical power. In a second step, the responsivity a...

  12. Nano electro-mechanical optoelectronic tunable VCSEL.

    Science.gov (United States)

    Huang, Michael C Y; Zhou, Ye; Chang-Hasnain, Connie J

    2007-02-05

    We report a novel electrostatic actuated nano-electromechanical optoelectronic (NEMO) tunable vertical-cavity surface-emitting laser (VCSEL) centered at 850 nm. By integrating a movable, single-layer (230 nm), high-index-contrast subwavelength grating (HCG) as the VCSEL top mirror, single mode emission (SMSR >40 dB) and continuous wavelength tuning (~2.5 nm) was obtained at room temperature under CW operation. The small footprint of HCG enables the scaling down of each of the cantilever dimensions by a factor of 10, leading to 1000 times reduction in mass, which potentially increases the mechanical resonant frequency and tuning speed.

  13. Coherent optoelectronics with single quantum dots

    Energy Technology Data Exchange (ETDEWEB)

    Zrenner, A; Ester, P; Michaelis de Vasconcellos, S; Huebner, M C; Lackmann, L; Stufler, S [Universitaet Paderborn, Department Physik, Warburger Strasse 100, D-33098 Paderborn (Germany); Bichler, M [Walter Schottky Institut, Technische Universitaet Muenchen, Am Coulombwall, D-85748 Garching (Germany)], E-mail: zrenner@mail.upb.de

    2008-11-12

    The optical properties of semiconductor quantum dots are in many respects similar to those of atoms. Since quantum dots can be defined by state-of-the-art semiconductor technologies, they exhibit long-term stability and allow for well-controlled and efficient interactions with both optical and electrical fields. Resonant ps excitation of single quantum dot photodiodes leads to new classes of coherent optoelectronic functions and devices, which exhibit precise state preparation, phase-sensitive optical manipulations and the control of quantum states by electrical fields.

  14. Feature issue introduction: halide perovskites for optoelectronics.

    Science.gov (United States)

    White, Thomas P; Deleporte, Emmanuelle; Sum, Tze-Chien

    2018-01-22

    This joint Optics Express and Optical Materials Express feature issue presents a collection of nine papers on the topic of halide perovskites for optoelectronics. Perovskite materials have attracted significant attention over the past four years, initially for their outstanding performance in thin film solar cells, but more recently for applications in light-emitting devices (LEDs and lasers), photodetectors and nonlinear optics. At the same time, there is still much more to learn about the fundamental properties of these materials, and how these depend on composition, processing, and exposure to the environment. This feature issue provides a snapshot of some of the latest research in this rapidly-evolving multidisciplinary field.

  15. Smart Optoelectronic Sensors and Intelligent Sensor Systems

    Directory of Open Access Journals (Sweden)

    Sergey Y. YURISH

    2012-03-01

    Full Text Available Light-to-frequency converters are widely used in various optoelectronic sensor systems. However, a further frequency-to-digital conversion is a bottleneck in such systems due to a broad frequency range of light-to-frequency converters’ outputs. This paper describes an effective OEM design approach, which can be used for smart and intelligent sensor systems design. The design is based on novel, multifunctional integrated circuit of Universal Sensors & Transducers Interface especially designed for such sensor applications. Experimental results have confirmed an efficiency of this approach and high metrological performances.

  16. BANDWIDTH AND EFFICIENT ENCODING SCHEME COMBINING TCM-UGM TO STBC

    OpenAIRE

    ABDELMOUNAIM MOULAY LAKHDAR; MOHAMMED BELADGHAM; ABDESSELAM BASSOU,; MOHAMED BENAISSA

    2011-01-01

    In this paper, a bandwidth efficient encoding scheme is proposed. It combines the modified version of trellis coded-modulation (called trellis coded-modulation with Ungerboeck-Gray mapping, TCM-UGM) to space-time block code (STBC). The performance of this encoding scheme is investigated over memoryless Rayleigh fading (MRF) channel for throughput 2 bits/s/Hz. The simulation result, using 2/3 rate 16-state TCM-UGM encoder, two transmit antennas and two receive antennas, shows clearly that the ...

  17. Compact antenna arrays with wide bandwidth and low sidelobe levels

    Science.gov (United States)

    Strassner, II, Bernd H.

    2014-09-09

    Highly efficient, low cost, easily manufactured SAR antenna arrays with lightweight low profiles, large instantaneous bandwidths and low SLL are disclosed. The array topology provides all necessary circuitry within the available antenna aperture space and between the layers of material that comprise the aperture. Bandwidths of 15.2 GHz to 18.2 GHz, with 30 dB SLLs azimuthally and elevationally, and radiation efficiencies above 40% may be achieved. Operation over much larger bandwidths is possible as well.

  18. PIC Simulation of Laser Plasma Interactions with Temporal Bandwidths

    Science.gov (United States)

    Tsung, Frank; Weaver, J.; Lehmberg, R.

    2015-11-01

    We are performing particle-in-cell simulations using the code OSIRIS to study the effects of laser plasma interactions in the presence of temperal bandwidths under conditions relevant to current and future shock ignition experiments on the NIKE laser. Our simulations show that, for sufficiently large bandwidth, the saturation level, and the distribution of hot electrons, can be effected by the addition of temporal bandwidths (which can be accomplished in experiments using smoothing techniques such as SSD or ISI). We will show that temporal bandwidth along play an important role in the control of LPI's in these lasers and discuss future directions. This work is conducted under the auspices of NRL.

  19. Frequency Bandwidth Optimization of Left-Handed Metamaterial

    Science.gov (United States)

    Chevalier, Christine T.; Wilson, Jeffrey D.

    2004-01-01

    Recently, left-handed metamaterials (LHM s) have been demonstrated with an effective negative index of refraction and with antiparallel group and phase velocities for microwave radiation over a narrow frequency bandwidth. In order to take advantage of these characteristics for practical applications, it will be beneficial to develop LHM s with increased frequency bandwidth response and lower losses. In this paper a commercial three-dimensional electromagnetic simulation code is used to explore the effects of geometry parameter variations on the frequency bandwidth of a LHM at microwave frequencies. Utilizing an optimizing routine in the code, a geometry was generated with a bandwidth more than twice as large as the original geometry.

  20. Optical Computations for Image Bandwidth Compression.

    Science.gov (United States)

    1982-05-15

    e.g., DPCM . Future research will consider the effect of the sampling scheme on single-band methods. The performance of various reconstruction-window...for spatial compression alg-orithms, such as differential pulse code modulation ( DPCM ), etc. The typical examples are adaptive prediction and...paralleled by a similar shift in data compres- sion schemes, from spatially nonadaptive M N-i M-i differential pulse code modulation ( DPCM ) sys- R(J

  1. Optoelectronic pH Meter: Further Details

    Science.gov (United States)

    Jeevarajan, Antony S.; Anderson, Mejody M.; Macatangay, Ariel V.

    2009-01-01

    A collection of documents provides further detailed information about an optoelectronic instrument that measures the pH of an aqueous cell-culture medium to within 0.1 unit in the range from 6.5 to 7.5. The instrument at an earlier stage of development was reported in Optoelectronic Instrument Monitors pH in a Culture Medium (MSC-23107), NASA Tech Briefs, Vol. 28, No. 9 (September 2004), page 4a. To recapitulate: The instrument includes a quartz cuvette through which the medium flows as it is circulated through a bioreactor. The medium contains some phenol red, which is an organic pH-indicator dye. The cuvette sits between a light source and a photodetector. [The light source in the earlier version comprised red (625 nm) and green (558 nm) light-emitting diodes (LEDs); the light source in the present version comprises a single green- (560 nm)-or-red (623 nm) LED.] The red and green are repeatedly flashed in alternation. The responses of the photodiode to the green and red are processed electronically to obtain the ratio between the amounts of green and red light transmitted through the medium. The optical absorbance of the phenol red in the green light varies as a known function of pH. Hence, the pH of the medium can be calculated from the aforesaid ratio.

  2. Nano-optoelectronics. Concepts, physics and devices

    Energy Technology Data Exchange (ETDEWEB)

    Grundmann, M. (ed.) [Leipzig Univ. (Germany). Inst. fuer Experimentelle Physik 2 - Halbleiterphysik

    2002-07-01

    In Part I of this book the underlying concepts of nano-optoelectronics, namely semiconductor heterostructures (Chap. 1) and stress-engineering of semiconductors (Chap. 2), are covered. In Part II the new physics in nanostructures is discussed. The first contributions focus on the structural properties investigated by transmission electron microscopy, planar and cross-sectional scanning tunneling microscopy and X-ray diffraction (Chaps. 3-6). In Chap. 7 the theory of electronic and optical properties of quantum dots is discussed. In Chap. 8 the electronic properties of quantum dots are investigated using magnetotunneling spectroscopy. In Chaps. 9-11 optical properties are discussed with focus on the dielectric function, interband transitions and condensation phenomena, respectively. The application of these novel properties in nano-optoelectronic devices is the focal point of Part III. In Chap. 12 the theory of quantum dot lasers is presented. The following contributions focus on experimental results on active devices, i.e., lasers (Chaps. 13-17) with focus on long-wavelength, red, blue/UV, high power, and mid-infrared (inter-sublevel) emission as well as amplifiers (Chap. 18). (orig.)

  3. Optoelectronic inventory system for special nuclear material

    International Nuclear Information System (INIS)

    Sieradzki, F.H.

    1994-01-01

    In support of the Department of Energy's Dismantlement Program, the Optoelectronics Characterization and Sensor Development Department 2231 at Sandia National Laboratories/New Mexico has developed an in situ nonintrusive Optoelectronic Inventory System (OIS) that has the potential for application wherever periodic inventory of selected material is desired. Using a network of fiber-optic links, the OIS retrieves and stores inventory signatures from data storage devices (which are permanently attached to material storage containers) while inherently providing electromagnetic pulse immunity and electrical noise isolation. Photovoltaic cells (located within the storage facility) convert laser diode optic power from a laser driver to electrical energy. When powered and triggered, the data storage devices sequentially output their digital inventory signatures through light-emitting diode/photo diode data links for retrieval and storage in a mobile data acquisition system. An item's exact location is determined through fiber-optic network and software design. The OIS provides an on-demand method for obtaining acceptable inventory reports while eliminating the need for human presence inside the material storage facility. By using modularization and prefabricated construction with mature technologies and components, an OIS installation with virtually unlimited capacity can be tailored to the customer's requirements

  4. An Optoelectronic Equivalent Narrowband Filter for High Resolution Optical Spectrum Analysis

    Directory of Open Access Journals (Sweden)

    Kunpeng Feng

    2017-02-01

    Full Text Available To achieve a narrow bandwidth optical filter with a wide swept range for new generation optical spectrum analysis (OSA of high performance optical sensors, an optoelectronic equivalent narrowband filter (OENF was investigated and a swept optical filter with bandwidth of several MHz and sweep range of several tens of nanometers was built using electric filters and a sweep laser as local oscillator (LO. The principle of OENF is introduced and analysis of the OENF system is presented. Two electric filters are optimized to be RBW filters for high and medium spectral resolution applications. Both simulations and experiments are conducted to verify the OENF principle and the results show that the power uncertainty is less than 1.2% and the spectral resolution can reach 6 MHz. Then, a real-time wavelength calibration system consisting of a HCN gas cell and Fabry–Pérot etalon is proposed to guarantee a wavelength accuracy of ±0.4 pm in the C-band and to reduce the influence of phase noise and nonlinear velocity of the LO sweep. Finally, OSA experiments on actual spectra of various optical sensors are conducted using the OENF system. These experimental results indicate that OENF system has an excellent capacity for the analysis of fine spectrum structures.

  5. High-Bandwidth White-Light System Combining a Micro-LED with Perovskite Quantum Dots for Visible Light Communication.

    Science.gov (United States)

    Mei, Shiliang; Liu, Xiaoyan; Zhang, Wanlu; Liu, Ran; Zheng, Lirong; Guo, Ruiqian; Tian, Pengfei

    2018-02-14

    This work proposes a high-bandwidth white-light system consisting of a blue gallium nitride (GaN) micro-LED (μLED) exciting yellow-emitting CsPbBr 1.8 I 1.2 perovskite quantum dots (YQDs) for high-speed real-time visible light communication (VLC). The packaged 80 μm × 80 μm blue-emitting μLED has a modulation bandwidth of ∼160 MHz and a peak emission wavelength of ∼445 nm. The achievable bandwidth of the white-light system is up to 85 MHz in the absence of filters and equalization technology. Meanwhile, the bandwidth of the YQDs as a color converter is as high as 73 MHz with the blue GaN μLED as the pump source. A maximum data rate of 300 Mbps can be achieved by taking advantage of the high bandwidth of the white-light system using the non-return-to-zero on-off keying (NRZ-OOK) modulation scheme. The resultant bit-error rate is 2.0 × 10 -3 , well beneath the forward error correction criterion of 3.8 × 10 -3 required for error-free data transmission. In addition, the YQDs which we proposed as a color converter possess high stability for VLC. After half a year, the achievable bandwidths of the white-light system and the YQDs are still up to 83 and 70 MHz, respectively. This study provides the direction of developing high-bandwidth white-light system for both high-efficiency solid-state lighting and high-speed VLC.

  6. Reduced bandwidth video for remote vehicle operations

    Energy Technology Data Exchange (ETDEWEB)

    Noell, T.E.; DePiero, F.W.

    1993-08-01

    Oak Ridge National Laboratory staff have developed a video compression system for low-bandwidth remote operations. The objective is to provide real-time video at data rates comparable to available tactical radio links, typically 16 to 64 thousand bits per second (kbps), while maintaining sufficient quality to achieve mission objectives. The system supports both continuous lossy transmission of black and white (gray scale) video for remote driving and progressive lossless transmission of black and white images for remote automatic target acquisition. The average data rate of the resulting bit stream is 64 kbps. This system has been demonstrated to provide video of sufficient quality to allow remote driving of a High-Mobility Multipurpose Wheeled Vehicle at speeds up to 15 mph (24.1 kph) on a moguled dirt track. The nominal driving configuration provides a frame rate of 4 Hz, a compression per frame of 125:1, and a resulting latency of {approximately}1s. This paper reviews the system approach and implementation, and further describes some of our experiences when using the system to support remote driving.

  7. Introduction to organic electronic and optoelectronic materials and devices

    CERN Document Server

    Sun, Sam-Shajing

    2008-01-01

    Introduction to Optoelectronic Materials, N. Peyghambarian and M. Fallahi Introduction to Optoelectronic Device Principles, J. Piprek Basic Electronic Structures and Charge Carrier Generation in Organic Optoelectronic Materials, S.-S. Sun Charge Transport in Conducting Polymers, V.N. Prigodin and A.J. Epstein Major Classes of Organic Small Molecules for Electronic and Optoelectronics, X. Meng, W. Zhu, and H. Tian Major Classes of Conjugated Polymers and Synthetic Strategies, Y. Li and J. Hou Low Energy Gap, Conducting, and Transparent Polymers, A. Kumar, Y. Ner, and G.A. Sotzing Conjugated Polymers, Fullerene C60, and Carbon Nanotubes for Optoelectronic Devices, L. Qu, L. Dai, and S.-S. Sun Introduction of Organic Superconducting Materials, H. Mori Molecular Semiconductors for Organic Field-Effect Transistors, A. Facchetti Polymer Field-Effect Transistors, H.G.O. Sandberg Organic Molecular Light-Emitting Materials and Devices, F. So and J. Shi Polymer Light-Emitting Diodes: Devices and Materials, X. Gong and ...

  8. Energy and bandwidth-efficient wireless transmission

    CERN Document Server

    Gao, Wei

    2017-01-01

    This book introduces key modulation and predistortion techniques for approaching energy and spectrum-efficient transmission for wireless communication systems. The book presents a combination of theoretical principles, practical implementations, and actual tests. It focuses on spectrum-efficient modulation and energy-efficient transmission techniques in the portable wireless communication systems, and introduces currently developed and designed RF transceivers in the latest wireless markets. Most materials, design examples, and design strategies used are based on the author’s two decades of work in the digital communication fields, especially in the areas of the digital modulations, demodulations, digital signal processing, and linearization of power amplifiers. The applications of these practical products and equipment cover the satellite communications on earth station systems, microwave communication systems, 2G GSM and 3G WCDMA mobile communication systems, and 802.11 WLAN systems.

  9. Orientation masking and cross-orientation suppression (XOS): implications for estimates of filter bandwidth.

    Science.gov (United States)

    Meese, Tim S; Holmes, David J

    2010-10-01

    Most contemporary models of spatial vision include a cross-oriented route to suppression (masking from a broadly tuned inhibitory pool), which is most potent at low spatial and high temporal frequencies (T. S. Meese & D. J. Holmes, 2007). The influence of this pathway can elevate orientation-masking functions without exciting the target mechanism, and because early psychophysical estimates of filter bandwidth did not accommodate this, it is likely that they have been overestimated for this corner of stimulus space. Here we show that a transient 40% contrast mask causes substantial binocular threshold elevation for a transient vertical target, and this declines from a mask orientation of 0° to about 40° (indicating tuning), and then more gently to 90°, where it remains at a factor of ∼4. We also confirm that cross-orientation masking is diminished or abolished at high spatial frequencies and for sustained temporal modulation. We fitted a simple model of pedestal masking and cross-orientation suppression (XOS) to our data and those of G. C. Phillips and H. R. Wilson (1984) and found the dependency of orientation bandwidth on spatial frequency to be much less than previously supposed. An extension of our linear spatial pooling model of contrast gain control and dilution masking (T. S. Meese & R. J. Summers, 2007) is also shown to be consistent with our results using filter bandwidths of ±20°. Both models include tightly and broadly tuned components of divisive suppression. More generally, because XOS and/or dilution masking can affect the shape of orientation-masking curves, we caution that variations in bandwidth estimates might reflect variations in processes that have nothing to do with filter bandwidth.

  10. Bandwidth selection in smoothing functions | Kibua | East African ...

    African Journals Online (AJOL)

    ... inexpensive and, hence, worth adopting. We argue that the bandwidth parameter is determined by two factors: the kernel function and the length of the smoothing region. We give an illustrative example of its application using real data. Keywords: Kernel, Smoothing functions, Bandwidth > East African Journal of Statistics ...

  11. Variable Bandwidth Analog Channel Filters for Software Defined Radio

    NARCIS (Netherlands)

    Arkesteijn, V.J.; Klumperink, Eric A.M.; Nauta, Bram

    2001-01-01

    An important aspect of Software Defined Radio is the ability to define the bandwidth of the filter that selects the desired channel. This paper first explains the importance of channel filtering. Then the advantage of analog channel filtering with a variable bandwidth in a Software Defined Radio is

  12. modeling the effect of bandwidth allocation on network performance

    African Journals Online (AJOL)

    Modeling The Effect Of Bandwidth Allocation On Network Performance. MODELING THE EFFECT OF BANDWIDTH ... ABSTRACT. In this paper, a new channel capacity model for interference- limited systems was obtained .... congestion admission control, with the intent of minimizing energy consumption at each terminal.

  13. Dental impression technique using optoelectronic devices

    Science.gov (United States)

    Sinescu, Cosmin; Barua, Souman; Topala, Florin Ionel; Negrutiu, Meda Lavinia; Duma, Virgil-Florin; Gabor, Alin Gabriel; Zaharia, Cristian; Bradu, Adrian; Podoleanu, Adrian G.

    2018-03-01

    INTRODUCTION: The use of Optical Coherence Tomography (OCT) as a non-invasive and high precision quantitative information providing tool has been well established by researches within the last decade. The marginal discrepancy values can be scrutinized in optical biopsy made in three dimensional (3D) micro millimetre scale and reveal detailed qualitative and quantitative information of soft and hard tissues. OCT-based high resolution 3D images can provide a significant impact on finding recurrent caries, restorative failure, analysing the precision of crown preparation, and prosthetic elements marginal adaptation error with the gingiva and dental hard tissues. During the CAD/CAM process of prosthodontic restorations, the circumvent of any error is important for the practitioner and the technician to reduce waste of time and material. Additionally, OCT images help to achieve a new or semi-skilled practitioner to analyse their crown preparation works and help to develop their skills faster than in a conventional way. The aim of this study is to highlight the advantages of OCT in high precision prosthodontic restorations. MATERIALS AND METHODS: 25 preparations of frontal and lateral teeth were performed for 7 different patients. The impressions of the prosthetic fields were obtained both using a conventional optoelectronic system (Apolo Di, Syrona) and a Spectral Domain using OCT (Dental prototype, working at 860 nm). For the conventional impression technique the preparation margins were been prelevated by gingival impregnated cords. No specific treatments were performed by the OCT impression technique. RESULTS: The scanning performed by conventional optoelectronic system proved to be quick and accurate in terms of impression technology. The results were represented by 3D virtual models obtained after the scanning procedure was completed. In order to obtain a good optical impression a gingival retraction cord was inserted between the prepared tooth and the gingival

  14. Metal Complexes for Organic Optoelectronic Applications

    Science.gov (United States)

    Huang, Liang

    Organic optoelectronic devices have drawn extensive attention by over the past two decades. Two major applications for Organic optoelectronic devices are efficient organic photovoltaic devices(OPV) and organic light emitting diodes (OLED). Organic Solar cell has been proven to be compatible with the low cost, large area bulk processing technology and processed high absorption efficiencies compared to inorganic solar cells. Organic light emitting diodes are a promising approach for display and solid state lighting applications. To improve the efficiency, stability, and materials variety for organic optoelectronic devices, several emissive materials, absorber-type materials, and charge transporting materials were developed and employed in various device settings. Optical, electrical, and photophysical studies of the organic materials and their corresponding devices were thoroughly carried out. In this thesis, Chapter 1 provides an introduction to the background knowledge of OPV and OLED research fields presented. Chapter 2 discusses new porphyrin derivatives- azatetrabenzylporphyrins for OPV and near infrared OLED applications. A modified synthetic method is utilized to increase the reaction yield of the azatetrabenzylporphyrin materials and their photophysical properties, electrochemical properties are studied. OPV devices are also fabricated using Zinc azatetrabenzylporphyrin as donor materials. Pt(II) azatetrabenzylporphyrin were also synthesized and used in near infra-red OLED to achieve an emission over 800 nm with reasonable external quantum efficiencies. Chapter 3, discusses the synthesis, characterization, and device evaluation of a series of tetradentate platinum and palladium complexesfor single doped white OLED applications and RGB white OLED applications. Devices employing some of the developed emitters demonstrated impressively high external quantum efficiencies within the range of 22%-27% for various emitter concentrations. And the palladium complex, i

  15. Hybrid optoelectronic correlator architecture for shift-invariant target recognition.

    Science.gov (United States)

    Monjur, Mehjabin Sultana; Tseng, Shih; Tripathi, Renu; Donoghue, John James; Shahriar, M S

    2014-01-01

    In this paper, we present theoretical details and the underlying architecture of a hybrid optoelectronic correlator (HOC) that correlates images using spatial light modulators (SLMs), detector arrays, and field programmable gate array (FPGA). The proposed architecture bypasses the need for nonlinear materials such as photorefractive polymer films by using detectors instead, and the phase information is yet conserved by the interference of plane waves with the images. However, the output of such an HOC has four terms: two convolution signals and two cross-correlation signals. By implementing a phase stabilization and scanning circuit, the convolution terms can be eliminated, so that the behavior of an HOC becomes essentially identical to that of a conventional holographic correlator (CHC). To achieve the ultimate speed of such a correlator, we also propose an integrated graphic processing unit, which would perform all the electrical processes in a parallel manner. The HOC architecture along with the phase stabilization technique would thus be as good as a CHC, capable of high-speed image recognition in a translation-invariant manner.

  16. Radiation-hard Optoelectronics for LHC detector upgrades.

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00375195; Newbold, Dave

    A series of upgrades foreseen for the LHC over the next decade will allow the proton-proton collisions to reach the design center of mass energy of 14 TeV and increase the luminosity to five times (High Luminosity-LHC) the design luminosity by 2027. Radiation-tolerant high-speed optical data transmission links will continue to play an important role in the infrastructure of particle physics experiments over the next decade. A new generation of optoelectronics that meet the increased performance and radiation tolerance limits imposed by the increase in the intensity of the collisions at the interaction points are currently being developed. This thesis focuses on the development of a general purpose bi-directional 5 Gb/s radiation tolerant optical transceiver, the Versatile Transceiver (VTRx), for use by the LHC experiments over the next five years, and on exploring the radiation-tolerance of state-of-the art silicon photonics modulators for HL-LHC data transmission applications. The compliance of the VTRx ...

  17. Analysis of mobile fronthaul bandwidth and wireless transmission performance in split-PHY processing architecture.

    Science.gov (United States)

    Miyamoto, Kenji; Kuwano, Shigeru; Terada, Jun; Otaka, Akihiro

    2016-01-25

    We analyze the mobile fronthaul (MFH) bandwidth and the wireless transmission performance in the split-PHY processing (SPP) architecture, which redefines the functional split of centralized/cloud RAN (C-RAN) while preserving high wireless coordinated multi-point (CoMP) transmission/reception performance. The SPP architecture splits the base stations (BS) functions between wireless channel coding/decoding and wireless modulation/demodulation, and employs its own CoMP joint transmission and reception schemes. Simulation results show that the SPP architecture reduces the MFH bandwidth by up to 97% from conventional C-RAN while matching the wireless bit error rate (BER) performance of conventional C-RAN in uplink joint reception with only 2-dB signal to noise ratio (SNR) penalty.

  18. Physically Connected Stacked Patch Antenna Design with 100% Bandwidth

    KAUST Repository

    Klionovski, Kirill

    2017-11-01

    Typically, stacked patch antennas are parasitically coupled and provide larger bandwidth than a single patch antenna. Here, we show a stacked patch antenna design where square patches with semi-circular cutouts are physically connected to each other. This arrangement provides 100% bandwidth from 23.9–72.2 GHz with consistent high gain (5 dBi or more) across the entire bandwidth. In another variation, a single patch loaded with a superstrate provides 83.5% bandwidth from 25.6–62.3 GHz. The mechanism of bandwidth enhancement is explained through electromagnetic simulations. Measured reflection coefficient, radiation patterns and gain results confirm the extremely wideband performance of the design.

  19. Optoelectronic iron detectors for pharmaceutical flow analysis.

    Science.gov (United States)

    Rybkowska, Natalia; Koncki, Robert; Strzelak, Kamil

    2017-10-25

    Compact flow-through optoelectronic detectors fabricated by pairing of light emitting diodes have been applied for development of economic flow analysis systems dedicated for iron ions determination. Three analytical methods with different chromogens selectively recognizing iron ions have been compared. Ferrozine and ferene S based methods offer higher sensitivity and slightly lower detection limits than method with 1,10-phenantroline, but narrower ranges of linear response. Each system allows detection of iron in micromolar range of concentration with comparable sample throughput (20 injections per hour). The developed flow analysis systems have been successfully applied for determination of iron in diet supplements. The utility of developed analytical systems for iron release studies from drug formulations has also been demonstrated. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Electroactive and Optoelectronically Active Graphene Nanofilms

    DEFF Research Database (Denmark)

    Chi, Qijin

    As an atomic-scale-thick two-dimensional material, graphene has emerged as one of the most miracle materials and has generated intensive interest in physics, chemistry and even biology in the last decade [1, 2]. Nanoscale engineering and functionalization of graphene is a crucial step for many...... applications ranging from catalysis, electronic devices, sensors to advanced energy conversion and storage [3]. This talk highlights our recent studies on electroactive and optoelectronically active graphene ultrathin films for chemical sensors and energy technology. The presentation includes a general theme...... for functionalization of graphene nanosheets, followed by showing several case studies. Our systems cover redox-active nanoparticles, electroactive supramolecular ensembles and redox enzymes which are integrated with graphene nanosheets as building blocks for the construction of functional thin films or graphene papers....

  1. Computational modeling of semiconductor nanostructures for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Veprek, Ratko G.

    2009-07-01

    This dissertation deals with parts of the theory and its numerical implementation of a novel simulator tdkp/AQUA, suitable for the unified simulation of nanostructures for optoelectronics of any dimensionality. Here, the calculation of realistic electronic band structure, including strain and polarization effects, and the optical properties of nanostructures are covered. The presented theory is based on a continuum formulation of the physical behavior of the involved semiconductor crystal. As a central novelty, the k*p envelope function method for the band structure calculation is formulated absolutely spurious solution free by ensuring a mathematical consistent formulation retaining the elliptical nature of the equation. The optical properties are calculated within a density matrix formalism. Many-body effects due to Coulomb interactions between charge carriers are included on the level of the screened Hartree-Fock theory. At the end, an analysis of GaN-nanocolumn LEDs using the developed simulator is presented. (orig.)

  2. Implantable optoelectronic probes for in vivo optogenetics

    Science.gov (United States)

    Iseri, Ege; Kuzum, Duygu

    2017-06-01

    More than a decade has passed since optics and genetics came together and lead to the emerging technologies of optogenetics. The advent of light-sensitive opsins made it possible to optically trigger the neurons into activation or inhibition by using visible light. The importance of spatiotemporally isolating a segment of a neural network and controlling nervous signaling in a precise manner has driven neuroscience researchers and engineers to invest great efforts in designing high precision in vivo implantable devices. These efforts have focused on delivery of sufficient power to deep brain regions, while monitoring neural activity with high resolution and fidelity. In this review, we report the progress made in the field of hybrid optoelectronic neural interfaces that combine optical stimulation with electrophysiological recordings. Different approaches that incorporate optical or electrical components on implantable devices are discussed in detail. Advantages of various different designs as well as practical and fundamental limitations are summarized to illuminate the future of neurotechnology development.

  3. 47 CFR 2.202 - Bandwidths.

    Science.gov (United States)

    2010-10-01

    ... television, computation in accordance with provisions of paragraph (f) of this section and formulas and... the only characteristic of an emission to be considered in evaluating the interference that may be... preemphasis or phase modulation, this value of per-channel deviation shall be specified at the characteristic...

  4. Integrated NEMS and optoelectronics for sensor applications.

    Energy Technology Data Exchange (ETDEWEB)

    Czaplewski, David A.; Serkland, Darwin Keith; Olsson, Roy H., III; Bogart, Gregory R. (Symphony Acoustics, Rio Rancho, NM); Krishnamoorthy, Uma; Warren, Mial E.; Carr, Dustin Wade (Symphony Acoustics, Rio Rancho, NM); Okandan, Murat; Peterson, Kenneth Allen

    2008-01-01

    This work utilized advanced engineering in several fields to find solutions to the challenges presented by the integration of MEMS/NEMS with optoelectronics to realize a compact sensor system, comprised of a microfabricated sensor, VCSEL, and photodiode. By utilizing microfabrication techniques in the realization of the MEMS/NEMS component, the VCSEL and the photodiode, the system would be small in size and require less power than a macro-sized component. The work focused on two technologies, accelerometers and microphones, leveraged from other LDRD programs. The first technology was the nano-g accelerometer using a nanophotonic motion detection system (67023). This accelerometer had measured sensitivity of approximately 10 nano-g. The Integrated NEMS and optoelectronics LDRD supported the nano-g accelerometer LDRD by providing advanced designs for the accelerometers, packaging, and a detection scheme to encapsulate the accelerometer, furthering the testing capabilities beyond bench-top tests. A fully packaged and tested die was never realized, but significant packaging issues were addressed and many resolved. The second technology supported by this work was the ultrasensitive directional microphone arrays for military operations in urban terrain and future combat systems (93518). This application utilized a diffraction-based sensing technique with different optical component placement and a different detection scheme from the nano-g accelerometer. The Integrated NEMS LDRD supported the microphone array LDRD by providing custom designs, VCSELs, and measurement techniques to accelerometers that were fabricated from the same operational principles as the microphones, but contain proof masses for acceleration transduction. These devices were packaged at the end of the work.

  5. Asymmetric MQW semiconductor optical amplifier with low-polarization sensitivity of over 90-nm bandwidth

    Science.gov (United States)

    Nkanta, Julie E.; Maldonado-Basilio, Ramón; Abdul-Majid, Sawsan; Zhang, Jessica; Hall, Trevor J.

    2013-12-01

    An exhausted capacity of current Passive Optical Networks has been anticipated as bandwidth-hungry applications such as HDTV and 3D video become available to end-users. To enhance their performance, the next generation optical access networks have been proposed, using optical carriers allocated within the E-band (1360-1460 nm). It is partly motivated by the low-water peak fiber being manufactured by Corning. At these wavelengths, choices for low cost optical amplifiers, with compact size, low energy consumption and feasibility for integration with other optoelectronic components are limited, making the semiconductor optical amplifiers (SOA) a realistic solution. An experimental characterization of a broadband and low polarization sensitive asymmetric multi quantum well (MQW) SOA operating in the E-band is reported. The SOA device is composed of nine 6 nm In1-xGaxAsyP1-y 0.2% tensile strained asymmetric MQW layers sandwiched between nine latticed matched 6 nm InGaAsP barrier layers. The active region is grown on an n-doped InP substrate and buried by p-doped InGaAsP layers. The SOA devices have 7-degrees tilt anti-reflected coated facets, with 2 μm ridge width, and a cavity length of 900 μm. For input powers of -10 dBm and -20 dBm, a maximum gain of 20 dB at 1360 nm with a polarization insensitivity under 3 dB for over 90 nm bandwidth is measured. Polarization sensitivity of less than 0.5 dB is observed for some wavelengths. Obtained results indicate a promising SOA with broadband amplification, polarization insensitivity and high gain. These SOAs were designed and characterized at the Photonics Technology Laboratory, University of Ottawa, Canada.

  6. Differential pulse code modulation

    Science.gov (United States)

    Herman, C. F. (Inventor)

    1976-01-01

    A differential pulse code modulation (DPCM) encoding and decoding method is described along with an apparatus which is capable of transmission with minimum bandwidth. The apparatus is not affected by data transition density, requires no direct current (DC) response of the transmission link, and suffers from minimal ambiguity in resolution of the digital data.

  7. Integral optoelectronic switch based on DMOS-transistors

    Directory of Open Access Journals (Sweden)

    Politanskyy L. F.

    2008-12-01

    Full Text Available The characteristics of optoelectronic couples photodiodes-DMOS-transistor are studied in the paper. There was developed a mathematical model of volt-ampere characteristic of the given optoelectronic couple which allows to determine interrelation of its electric parameters with constructive and electrophysical parameters of photodiodes and DMOS-transistors. There was suggested a construction of integral optoelectronic switch, based on DMOS-transistors on the silicon with dielectric insulation structures (SDIS. Possible is the optic control of executive devices, connected both to the source and drain circuits of the switching transistor.

  8. Energy efficiency in elastic-bandwidth optical networks

    DEFF Research Database (Denmark)

    Vizcaino, Jorge Lopez; Ye, Yabin; Tafur Monroy, Idelfonso

    2011-01-01

    The forecasted growth in the Internet traffic has made the operators and industry to be concerned about the power consumption of the networks, and to become interested in alternatives to plan and operate the networks in a more energy efficient manner. The introduction of OFDM, and its property...... of elastic bandwidth allocation, opens new horizons in the operation of optical networks. In this paper, we compare the network planning problem in an elastic bandwidth CO-OFDM-based network and a fixed-grid WDM network. We highlight the benefits that bandwidth elasticity and the selection of different...

  9. Optical technology for microwave applications VI and optoelectronic signal processing for phased-array antennas III; Proceedings of the Meeting, Orlando, FL, Apr. 20-23, 1992

    Science.gov (United States)

    Yao, Shi-Kay; Hendrickson, Brian M.

    The following topics related to optical technology for microwave applications are discussed: advanced acoustooptic devices, signal processing device technologies, optical signal processor technologies, microwave and optomicrowave devices, advanced lasers and sources, wideband electrooptic modulators, and wideband optical communications. The topics considered in the discussion of optoelectronic signal processing for phased-array antennas include devices, signal processing, and antenna systems.

  10. 16 Gb/s PAM4 UWOC system based on 488-nm LD with light injection and optoelectronic feedback techniques.

    Science.gov (United States)

    Li, Chung-Yi; Lu, Hai-Han; Tsai, Wen-Shing; Cheng, Ming-Te; Ho, Chun-Ming; Wang, Yun-Chieh; Yang, Zih-Yi; Chen, De-Yu

    2017-05-15

    A 16 Gb/s four-level pulse amplitude modulation (PAM4) underwater wireless optical communication (UWOC) system based on 488-nm laser diode (LD) with light injection and optoelectronic feedback techniques is proposed and successfully demonstrated. Experimental results show that such a 1.8-GHz 488-nm blue light LD with light injection and optoelectronic feedback techniques is enough forceful for a 16 Gb/s PAM4 signal underwater link. To the authors' knowledge, this study is the first to successfully adopt a 488-nm LD transmitter with light injection and optoelectronic feedback techniques in a PAM4 UWOC system. By adopting a 488-nm LD transmitter with light injection and optoelectronic feedback techniques, good bit error rate performance (offline processed by Matlab) and clear eye diagrams (measured in real-time) are achieved over a 10-m underwater link. The proposed system has the potential to play a vital role in the future UWOC infrastructure by effectively providing high transmission rate (16 Gb/s) and long underwater transmission distance (10 m).

  11. Functional Carbon Nanocomposite, Optoelectronic, and Catalytic Coatings

    Science.gov (United States)

    Liang, Yu Teng

    Over the past couple decades, fundamental research into carbon nanomaterials has produced a steady stream of groundbreaking physical science. Their record setting mechanical strength, chemical stability, and optoelectronic performance have fueled many optimistic claims regarding the breadth and pace of carbon nanotube and graphene integration. However, present synthetic, processing, and economic constraints have precluded these materials from many practical device applications. To overcome these limitations, novel synthetic techniques, processing methodologies, device geometries, and mechanistic insight were developed in this dissertation. The resulting advancements in material production and composite device performance have brought carbon nanomaterials ever closer to commercial implementation. For improved materials processing, vacuum co-deposition was first demonstrated as viable technique for forming carbon nanocomposite films without property distorting covalent modifications. Co-deposited nanoparticle, carbon nanotube, and graphene composite films enabled rapid device prototyping and compositional optimization. Cellulosic polymer stabilizers were then shown to be highly effective carbon nanomaterial dispersants, improving graphene production yields by two orders of magnitude in common organic solvents. By exploiting polarity interactions, iterative solvent exchange was used to further increase carbon nanomaterial dispersion concentrations by an additional order of magnitude, yielding concentrated inks. On top of their low causticity, these cellulosic nanomaterial inks have highly tunable viscosities, excellent film forming capacity, and outstanding thermal stability. These processing characteristics enable the efficient scaling of carbon nanomaterial coatings and device production using existing roll-to-roll fabrication techniques. Utilizing these process improvements, high-performance gas sensing, energy storage, transparent conductor, and photocatalytic

  12. Development of broad bandwidth nonlinear spectroscopies for characterization of electronic states in materials systems

    Science.gov (United States)

    Mehlenbacher, Randy D.

    Carbon nanotubes are an interesting class of materials with many exceptional properties that make them appealing for optoelectronic devices. Their optical properties, particularly when cast in thin films, are not well understood. In this thesis, I describe the development of spectroscopic techniques for measuring energy and charge transport processes in thin films of semiconducting carbon nanotubes. Using transient absorption spectroscopy, I observe energy transport on two time scales in these films, with 20% of nanotubes transferring energy to smaller bandgap nanotubes within 300 fs. After 3 ps, 70% of the photoexcitation resides on small bandgap nanotubes. To study the complete landscape of energy transport in thin films of carbon nanotubes, I developed two dimensional white light spectroscopy (2D-WL). In 2D-WL spectroscopy, a broadband, white light supercontinuum is used to both excite and probe the sample. This technique has a bandwidth spanning > 500-1500 nm, a far broader bandwidth than previously reported in 2D electronic spectra. I take advantage of this large bandwidth to study the interactions and evolution of S1 and S2 excitons in a thin film of carbon nanotubes. I find that energy transfers between S1 excitons on a 2 ps time scale and occurs by a non-Forster energy transfer mechanism. In contrast, the energy in the S2 states redistributes on an ultrafast time scale, films of bare, semiconducting carbon nanotubes. In these films, energy transfer occurs in <100 fs between bare carbon nanotubes and this energy transfer is between parallel nanotubes. By taking advantage of the laser pulse polarization for each interaction, I resolve otherwise difficult to observe couplings between electronic states. To facilitate data interpretation, the orientational response for isotropic two dimensional samples to polarized electric fields is developed. Using polarization control 2D-WL spectroscopy, I measure the coupling between nanotube S1 transitions and radial

  13. High-Bandwidth Dynamic Full-Field Profilometry for Nano-Scale Characterization of MEMS

    International Nuclear Information System (INIS)

    Chen, L-C; Huang, Y-T; Chang, P-B

    2006-01-01

    The article describes an innovative optical interferometric methodology to delivery dynamic surface profilometry with a measurement bandwidth up to 10MHz or higher and a vertical resolution up to 1 nm. Previous work using stroboscopic microscopic interferometry for dynamic characterization of micro (opto)electromechanical systems (M(O)EMS) has been limited in measurement bandwidth mainly within a couple of MHz. For high resonant mode analysis, the stroboscopic light pulse is insufficiently short to capture the moving fringes from dynamic motion of the detected structure. In view of this need, a microscopic prototype based on white-light stroboscopic interferometry with an innovative light superposition strategy was developed to achieve dynamic full-field profilometry with a high measurement bandwidth up to 10MHz or higher. The system primarily consists of an optical microscope, on which a Mirau interferometric objective embedded with a piezoelectric vertical translator, a high-power LED light module with dual operation modes and light synchronizing electronics unit are integrated. A micro cantilever beam used in AFM was measured to verify the system capability in accurate characterisation of dynamic behaviours of the device. The full-field seventh-mode vibration at a vibratory frequency of 3.7MHz can be fully characterized and nano-scale vertical measurement resolution as well as tens micrometers of vertical measurement range can be performed

  14. Bandwidth-tunable narrowband rectangular optical filter based on stimulated Brillouin scattering in optical fiber.

    Science.gov (United States)

    Wei, Wei; Yi, Lilin; Jaouën, Yves; Hu, Weisheng

    2014-09-22

    We propose a rectangular optical filter based on stimulated Brillouin scattering (SBS) in optical fiber with bandwidth tuning from 50 MHz to 4 GHz at less than 15-MHz resolution. The rectangular shape of the filter is precisely achieved utilizing digital feedback control of the comb-like pump spectral lines. The passband ripple is suppressed to ~1 dB by mitigating the nonlinearity influences of the comb-like pump lines generated in electrical and optical components and fibers. Moreover a fiber with a single Brillouin peak is employed to further reduce the in-band ripple and the out-of-band SBS gain at the same time. Finally, we analyze the noise performance of the filter at different bandwidth cases and demonstrate the system performance of the proposed filter with 2.1-GHz bandwidth and 19-dB gain by amplifying a 2-GHz orthogonal frequency-division-multiplexing (OFDM) signal with quadrature-phase-shift-keying (QPSK) and 16-quadrature-amplitude-modulation (16-QAM) on each subscriber.

  15. Basic opto-electronics on silicon for sensor applications

    NARCIS (Netherlands)

    Joppe, J.L.; Bekman, H.H.P.Th.; de Krijger, A.J.T.; Albers, H.; Chalmers, J.; Chalmers, J.D.; Holleman, J.; Ikkink, T.J.; Ikkink, T.; van Kranenburg, H.; Zhou, M.-J.; Zhou, Ming-Jiang; Lambeck, Paul

    1994-01-01

    A general platform for integrated opto-electronic sensor systems on silicon is proposed. The system is based on a hybridly integrated semiconductor laser, ZnO optical waveguides and monolithic photodiodes and electronic circuiry.

  16. Device-packaging method and apparatus for optoelectronic circuits

    Science.gov (United States)

    Zortman, William A.; Henry, Michael David; Jarecki, Jr., Robert L.

    2017-04-25

    An optoelectronic device package and a method for its fabrication are provided. The device package includes a lid die and an active die that is sealed or sealable to the lid die and in which one or more optical waveguides are integrally defined. The active die includes one or more active device regions, i.e. integral optoelectronic devices or etched cavities for placement of discrete optoelectronic devices. Optical waveguides terminate at active device regions so that they can be coupled to them. Slots are defined in peripheral parts of the active dies. At least some of the slots are aligned with the ends of integral optical waveguides so that optical fibers or optoelectronic devices inserted in the slots can optically couple to the waveguides.

  17. Optoelectronic Infrastructure for RF/Optical Phased Arrays, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — Optoelectronic integrated holds the key to higher performance, reduced mass and radiation-hard space systems. A special need is increased flexibility of phased...

  18. Basic Opto-electronics on Silicon for Sensor Applications

    NARCIS (Netherlands)

    Joppe, J.L.; Bekman, H.H.P.T.; Krijger, A.J.T. de; Lambeck, P.V.; Chalmers, J.; Holleman, J.; Ikkink, T.; Kranenburg, H. van; Zhou, M.J.

    1994-01-01

    A general platform for integrated opto-electronic sensor systems on silicon is proposed. The system is based on a hybridly integrated semiconductor laser, ZnO optical waveguides and monolithic photodiodes and electronic circuiry.

  19. Quantum dot optoelectronic devices: lasers, photodetectors and solar cells

    International Nuclear Information System (INIS)

    Wu, Jiang; Chen, Siming; Seeds, Alwyn; Liu, Huiyun

    2015-01-01

    Nanometre-scale semiconductor devices have been envisioned as next-generation technologies with high integration and functionality. Quantum dots, or the so-called ‘artificial atoms’, exhibit unique properties due to their quantum confinement in all 3D. These unique properties have brought to light the great potential of quantum dots in optoelectronic applications. Numerous efforts worldwide have been devoted to these promising nanomaterials for next-generation optoelectronic devices, such as lasers, photodetectors, amplifiers, and solar cells, with the emphasis on improving performance and functionality. Through the development in optoelectronic devices based on quantum dots over the last two decades, quantum dot devices with exceptional performance surpassing previous devices are evidenced. This review describes recent developments in quantum dot optoelectronic devices over the last few years. The paper will highlight the major progress made in 1.3 μm quantum dot lasers, quantum dot infrared photodetectors, and quantum dot solar cells. (topical review)

  20. Opto-electronic devices from block copolymers and their oligomers.

    NARCIS (Netherlands)

    Hadziioannou, G

    1997-01-01

    This paper presents research activities towards the development of polymer materials and devices for optoelectronics, An approach to controlling the conjugation length and transferring the luminescence properties of organic molecules to polymers through black copolymers containing well-defined

  1. Optoelectronic properties of individually positioned InAs nanowires

    Energy Technology Data Exchange (ETDEWEB)

    Overbeck, Jan; Brenneis, Andreas; Treu, Julian; Hertenberger, Simon; Abstreiter, Gerhard; Koblmueller, Gregor; Holleitner, Alexander [Walter Schottky Institut and Physik-Department, TU Muenchen, 85748 Garching (Germany)

    2013-07-01

    Small bandgap semiconducting nanowires offer a promising approach to fabricating nanoscale light-sensitive devices like broadband solar cells or mid-infrared photodetectors. We discuss the optoelectronic properties of individually positioned InAs nanowires on p-Si(111) substrates. The substrates exhibit a top layer of SiO{sub 2} which is structured via e-beam lithography creating holes in the oxide with a diameter of ∝80 nm. The nanowires are then grown vertically on the patterned substrates by solid-source molecular beam epitaxy. To fabricate optoelectronic devices, the nanowires are subsequently contacted via a thin, semitransparent metal film evaporated on top of an insulating layer (BCB). The p-Si substrate forms the second contact of the optoelectronic two-terminal devices. We discuss spatially resolved photocurrent measurements which give insights into the interplay of optoelectronic dynamics in single nanowires and in the Si-substrates.

  2. High bandwidth deflection readout for atomic force microscopes.

    Science.gov (United States)

    Steininger, Juergen; Bibl, Matthias; Yoo, Han Woong; Schitter, Georg

    2015-10-01

    This contribution presents the systematic design of a high bandwidth deflection readout mechanism for atomic force microscopes. The widely used optical beam deflection method is revised by adding a focusing lens between the cantilever and the quadrant photodetector (QPD). This allows the utilization of QPDs with a small active area resulting in an increased detection bandwidth due to the reduced junction capacitance. Furthermore the additional lens can compensate a cross talk between a compensating z-movement of the cantilever and the deflection readout. Scaling effects are analyzed to get the optimal spot size for the given geometry of the QPD. The laser power is tuned to maximize the signal to noise ratio without limiting the bandwidth by local saturation effects. The systematic approach results in a measured -3 dB detection bandwidth of 64.5 MHz at a deflection noise density of 62fm/√Hz.

  3. Bandwidth allocation and pricing problem for a duopoly market

    Directory of Open Access Journals (Sweden)

    You Peng-Sheng

    2011-01-01

    Full Text Available This research discusses the Internet service provider (ISP bandwidth allocation and pricing problems for a duopoly bandwidth market with two competitive ISPs. According to the contracts between Internet subscribers and ISPs, Internet subscribers can enjoy their services up to their contracted bandwidth limits. However, in reality, many subscribers may experience the facts that their on-line requests are denied or their connection speeds are far below their contracted speed limits. One of the reasons is that ISPs accept too many subscribers as their subscribers. To avoid this problem, ISPs can set limits for their subscribers to enhance their service qualities. This paper develops constrained nonlinear programming to deal with this problem for two competitive ISPs. The condition for reaching the equilibrium between the two competitive firms is derived. The market equilibrium price and bandwidth resource allocations are derived as closed form solutions.

  4. Increase of the grating coupler bandwidth with a graphene overlay

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Zhenzhou; Li, Zhen; Xu, Ke; Tsang, Hon Ki, E-mail: hktsang@ee.cuhk.edu.hk [Department of Electronic Engineering, The Chinese University of Hong Kong, Shatin (Hong Kong)

    2014-03-17

    We present theoretical and experimental results that demonstrate an increase in the grating bandwidth by placing a graphene on the chip. A focusing subwavelength grating with coupling efficiency of −4.3 dB and 1 dB bandwidth of ∼60 nm was demonstrated. After a graphene sheet was transferred onto the chip, the maximum 1 dB bandwidth was increased to ∼72 nm. Experimental results are consistent with the calculated graphene induced waveguide refractive index and dispersion changes, and the bandwidth improvement may be attributed to the reduction of grating dispersion. This study may be of interest for graphene-on-silicon photonic integrated circuit applications.

  5. Bandwidth Estimation in Wireless Lans for Multimedia Streaming Services

    Directory of Open Access Journals (Sweden)

    Heung Ki Lee

    2007-01-01

    Full Text Available The popularity of multimedia streaming services via wireless networks presents major challenges in the management of network bandwidth. One challenge is to quickly and precisely estimate the available bandwidth for the decision of streaming rates of layered and scalable multimedia services. Previous studies based on wired networks are too burdensome to be applied to multimedia applications in wireless networks. In this paper, a new method, IdleGap, is suggested to estimate the available bandwidth of a wireless LAN based on the information from a low layer in the protocol stack. We use a network simulation tool, NS-2, to evaluate our new method with various ranges of cross-traffic and observation times. Our simulation results show that IdleGap accurately estimates the available bandwidth for all ranges of cross-traffic (100 Kbps ∼ 1 Mbps with a very short observation time of 10 seconds.

  6. High-Bandwidth Hybrid Sensor (HYSENS), Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — ATA has demonstrated the primary innovation of combining a precision MEMS gyro (BAE SiRRS01) with a high bandwidth angular rate sensor, ATA's ARS-14 resulting in a...

  7. Bandwidth Efficient Overlapped FSK Coded Secure Command Transmission for Medical Implant Communication Systems

    Directory of Open Access Journals (Sweden)

    Selman KULAÇ

    2018-06-01

    Full Text Available Nowadays, wireless communication systems are exploited in most health care systems. Implantable Medical Systems (IMS also have wireless communication capability. However, it is very important that secure wireless communication should be provided in terms of both patient rights and patient health. Therefore, wireless transmission systems of IMS should also be robust against to eavesdroppers and adversaries. In this study, a specific overlapped and coded frequency shift keying (FSK modulation technique is developed and security containing with low complexity is provided by this proposed technique. The developed method is suitable for wireless implantable medical systems since it provides low complexity and security as well as bandwidth efficiency.

  8. Gain-switched all-fiber laser with narrow bandwidth

    DEFF Research Database (Denmark)

    Larsen, Casper; Giesberts, M.; Nyga, S.

    2013-01-01

    Gain-switching of a CW fiber laser is a simple and cost-effective approach to generate pulses using an all-fiber system. We report on the construction of a narrow bandwidth (below 0.1 nm) gain-switched fiber laser and optimize the pulse energy and pulse duration under this constraint. The extracted...... the bandwidth below 0.1 nm. This allows frequency doubling in a periodically poled lithium tantalate crystal with a reasonable conversion efficiency....

  9. Optoelectronic device with nanoparticle embedded hole injection/transport layer

    Science.gov (United States)

    Wang, Qingwu [Chelmsford, MA; Li, Wenguang [Andover, MA; Jiang, Hua [Methuen, MA

    2012-01-03

    An optoelectronic device is disclosed that can function as an emitter of optical radiation, such as a light-emitting diode (LED), or as a photovoltaic (PV) device that can be used to convert optical radiation into electrical current, such as a photovoltaic solar cell. The optoelectronic device comprises an anode, a hole injection/transport layer, an active layer, and a cathode, where the hole injection/transport layer includes transparent conductive nanoparticles in a hole transport material.

  10. Electron microscopy study of advanced heterostructures for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Katcki, J.; Ratajczak, J.; Phillipp, F.; Muszalski, J.; Bugajski, M.; Chen, J.X.; Fiore, A

    2003-08-28

    The application of cross-sectional transmission electron microscopy and scanning electron microscopy to the investigation of optoelectronic devices are reviewed. Special attention was paid to the electron microscopy assessment of the growth perfection of such crucial elements of the devices like quantum wells, quantum dots, distributed Bragg reflectors as well as electrical contacts. Using these examples, the most important issues of the application of electron microscopy to characterization of optoelectronic devices are discussed.

  11. Emissive polymeric materials for optoelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Shiang, Joseph John [Niskayuna, NY; Chichak, Kelly Scott [Clifton Park, NY; Cella, James Anthony [Clifton Park, NY; Lewis, Larry Neil [Scotia, NY; Janora, Kevin Henry [Schenectady, NY

    2011-07-05

    Polymers including at least one structural unit derived from a compound of formula I or including at least one pendant group of formula II may be used in optoelectronic devices ##STR00001## wherein R.sup.1, R.sup.3, R.sup.4 and R.sup.6 are independently hydrogen, alkyl, alkoxy, oxaalkyl, alkylaryl, aryl, arylalkyl, heteroaryl, substituted alkyl; substituted alkoxy, substituted oxaalkyl, substituted alkylaryl, substituted aryl, substituted arylalkyl, or substituted heteroaryl; R.sup.1a is hydrogen or alkyl; R.sup.2 is alkylene, substituted alkylene, oxaalkylene, CO, or CO.sub.2; R.sup.2a is alkylene; R.sup.5 is independently at each occurrence hydrogen, alkyl, alkylaryl, aryl, arylalkyl, alkoxy, carboxy, substituted alkyl; substituted alkylaryl, substituted aryl, substituted arylalkyl, or substituted alkoxy, X is halo, triflate, --B(OR.sup.1a).sub.2, or ##STR00002## located at the 2, 5- or 2, 7-positions; and L is derived from phenylpyridine, tolylpyridine, benzothienylpyridine, phenylisoquinoline, dibenzoquinozaline, fluorenylpyridine, ketopyrrole, 2-(1-naphthyl)benzoxazole)), 2-phenylbenzoxazole, 2-phenylbenzothiazole, coumarin, thienylpyridine, phenylpyridine, benzothienylpyridine, 3-methoxy-2-phenylpyridine, thienylpyridine, phenylimine, vinylpyridine, pyridylnaphthalene, pyridylpyrrole, pyridylimidazole, phenylindole, derivatives thereof or combinations thereof.

  12. Functionalized polyfluorenes for use in optoelectronic devices

    Energy Technology Data Exchange (ETDEWEB)

    Chichak, Kelly Scott [Clifton Park, NY; Lewis, Larry Neil [Scotia, NY; Cella, James Anthony [Clifton Park, NY; Shiang, Joseph John [Niskayuna, NY

    2011-11-08

    The present invention relates to process comprising reacting a polyfluorenes comprising at least one structural group of formula I ##STR00001## with an iridium (III) compound of formula II ##STR00002## wherein R.sup.1 and R.sup.2 are independently alkyl, substituted alkyl, aryl, substituted aryl or a combination thereof; R.sup.5is H or CHO; R.sup.3 and R.sup.4 are independently hydrogen, alkyl, substituted alkyl, aryl, substituted aryl or a combination thereof; R.sup.11 and R.sup.12 taken together form a substituted or unsubstituted monocyclic or bicyclic heteroaromatic ring; R.sup.13 is independently at each occurrence halo, nitro, hydroxy, amino, alkyl, aryl, arylalkyl, alkoxy, substituted alkoxy, substituted alkyl, substituted aryl, or substituted arylalkyl; Ar is aryl, heteroaryl, substituted aryl, substituted heteroaryl, or a combination thereof; X is selected from a direct bond, alky, substituted alkyl, and combinations thereof; Y is CHO or NH.sub.2; Z is CHO or NH.sub.2 where Z does not equal Y; and p is 0, 1 or 2. The invention also relates to the polyfluorenes, which are products of the reaction, and the use of the polyfluorenes in optoelectronic devices.

  13. Assessment of dental plaque by optoelectronic methods

    Science.gov (United States)

    Negrutiu, Meda-Lavinia; Sinescu, Cosmin; Bortun, Cristina Maria; Levai, Mihaela-Codrina; Topala, Florin Ionel; Crǎciunescu, Emanuela Lidia; Cojocariu, Andreea Codruta; Duma, Virgil Florin; Podoleanu, Adrian Gh.

    2016-03-01

    The formation of dental biofilm follows specific mechanisms of initial colonization on the surface, microcolony formation, development of organized three dimensional community structures, and detachment from the surface. The structure of the plaque biofilm might restrict the penetration of antimicrobial agents, while bacteria on a surface grow slowly and display a novel phenotype; the consequence of the latter is a reduced sensitivity to inhibitors. The aim of this study was to evaluate with different optoelectronic methods the morphological characteristics of the dental biofilm. The study was performed on samples from 25 patients aged between 18 and 35 years. The methods used in this study were Spectral Domain Optical Coherence Tomography (SD-OCT) working at 870 nm for in vivo evaluations and Scanning Electron Microscopy (SEM) for validations. For each patient a sample of dental biofilm was obtained directly from the vestibular surface of the teeth's. SD-OCT produced C- and B-scans that were used to generate three dimensional (3D) reconstructions of the sample. The results were compared with SEM evaluations. The biofilm network was dramatically destroyed after the professional dental cleaning. OCT noninvasive methods can act as a valuable tool for the 3D characterization of dental biofilms.

  14. Recent trend in graphene for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Yu-Bin, E-mail: benechen.bvo@gmail.com [National Taiwan University of Science and Technology, Graduate Institute of Management, Taiwan (China); Liu, John S., E-mail: johnliu@mail.ntust.edu.tw [National Taiwan University of Science and Technology, Graduate Institute of Technology Management, Taiwan (China); Lin Pang, E-mail: panglin@mail.nctu.edu.tw [National Chiao Tung University, Department of Materials Science and Engineering, Taiwan (China)

    2013-02-15

    This study analyzes the scientific knowledge diffusion paths of graphene for optoelectronics (GFO), where graphene offers wide applications due to its thinness, high conductivity, excellent transparency, chemical stability, robustness, and flexibility. Our investigation is based on the main path analysis which establishes the citation links among the literature data in order to trace the significant sequence of knowledge development in this emerging field. We identify the main development paths of GFO up to the year 2012, along which a series of influential papers in this field are identified. The main path graph shows that knowledge diffusion occurs in key subareas, including reduced graphene oxide, chemical vapor deposition, and exfoliation techniques, which are developed for the preparation and applications of GFO. The applications cover solar cells, laser devices, sensing devices, and LCD. In addition, the main theme of GFO research evolves in sequence from small-graphene-sample preparation, to large-scale film growth, and onto prototype device fabrication. This evolution reflects a strong industrial demand for a new transparent-conductive film technology.

  15. A silicon microbench concept for optoelectronic packaging

    Energy Technology Data Exchange (ETDEWEB)

    Pocha, M.D.; Strand, O.T.; Kerns, J.A.

    1996-06-24

    Optoelectronics (o/e) is currently too expensive for widespread application. We believe that the packaging (or fiber pigtailing) process must be automated to realize a significant reduction in the cost of o.e packages. We are addressing issues of automating the fiber pigtailing process on silicon waferboards or microbenches. This paper focuses on reflowing solders for the attachment of o/e components. We have recently developed miniature polysilicon heaters which are integrated on silicon microbenches. These miniature heaters avoid the problem of raising the entire microbench to the solder melting point to attach components. Most importantly, these miniature heaters are completely compatible with automating the attachment process. Designing silicon microbenches with on-board heaters requires some care. The thermal properties of the microbench itself along with all coatings and any heatsinking materials must be understood. The heaters must operate in a current and voltage regime compatible with the overall characteristics of the o.e package. Inadvertently reflowing solder in unanticipated locations may occur unless the thermal behavior of the microbench thoroughly known. This paper describes the design and fabrication of our microbenches and an experimental and theoretical study on these silicon microbenches which gives a complete picture of their thermal behavior.

  16. Optoelectronics in TESLA, LHC, and pi-of-the-sky experiments

    Science.gov (United States)

    Romaniuk, Ryszard S.; Pozniak, Krzysztof T.; Wrochna, Grzegorz; Simrock, Stefan

    2004-09-01

    Optical and optoelectronics technologies are more and more widely used in the biggest world experiments of high energy and nuclear physics, as well as in the astronomy. The paper is a kind of a broad digest describing the usage of optoelectronics is such experiments and information about some of the involved teams. The described experiments include: TESLA linear accelerator and FEL, Compact Muon Solenoid at LHC and recently started π-of-the-sky global gamma ray bursts (with asociated optical flashes) observation experiment. Optoelectornics and photonics offer several key features which are either extending the technical parameters of existing solutions or adding quite new practical application possibilities. Some of these favorable features of photonic systems are: high selectivity of optical sensors, immunity to some kinds of noise processes, extremely broad bandwidth exchangeable for either terabit rate transmission or ultrashort pulse generation, parallel image processing capability, etc. The following groups of photonic components and systems were described: (1) discrete components applications like: LED, PD, LD, CCD and CMOS cameras, active optical crystals and optical fibers in radiation dosimetry, astronomical image processing and for building of more complex photonic systems; (2) optical fiber networks serving as very stable phase distribution, clock signal distribution, distributed dosimeters, distributed gigabit transmission for control, diagnostics and data acquisition/processing; (3) fast and stable coherent femtosecond laser systems with active optical components for electro-optical sampling and photocathode excitation in the RF electron gun for linac; The parameters of some of these systems were quoted and discussed. A number of the debated solutions seems to be competitive against the classical ones. Several future fields seem to emerge involving direct coupling between the ultrafast photonic and the VLSI FPGA based technologies.

  17. TPROXY dan FILTERING SEBAGAI METODE OPTIMASI PEMAKAIAN BANDWIDTH INTERNET

    Directory of Open Access Journals (Sweden)

    Sutiyo Sutiyo

    2015-04-01

    Full Text Available Until now the use of the internet disuatu agencies viewed from the initial planning, use and care, even long-term planning is still not optimal. The main factor lies in the existing human resources, especially in IT personnel and policy makers who do not understand or do not even know at all how your use of the Internet well, optimal, efficient, particularly associated with the consumption of Internet bandwidth. Internet bandwidth capacity greatly affect the speed of web access or other Internet applications. So we need a plan and maintance necessary to obtain good Internet bandwidth consumption efficiency and guaranteed QoS, such as by utilizing Tproxy and filtering methods. TProxy is a development of which has been patched Squid, a proxy to be able to pass traffic without NAT (Network Access Translation. Fitering a firewall system which is used for filtering data packets that do not want filtered dikendaki or akhirmya able to minimize traffic on bandwidth usage. Tproxy and filtering runs on the Linux platform. Linux distributions are often used to Tproxy is a variant Debian, Centos and then to use Mikrotik Filtering. At the end of each request or query from the client or the response of the proxy server does not have meaningful constraints, the bandwidth between the client and the proxy server does not happen limitation, bandwidth capable of running close to capacity including 10 Mbps Ethernet, 100 Mbps, and even a GPS (full speed.

  18. Global characteristics of zonal flows due to the effect of finite bandwidth in drift wave turbulence

    International Nuclear Information System (INIS)

    Uzawa, K.; Li Jiquan; Kishimoto, Y.

    2009-01-01

    The spectral effect of the zonal flow (ZF) on its generation is investigated based on the Charney-Hasegawa-Mima turbulence model. It is found that the effect of finite ZF bandwidth qualitatively changes the characteristics of ZF instability. A spatially localized (namely, global) nonlinear ZF state with an enhanced, unique growth rate for all spectral components is created under a given turbulent fluctuation. It is identified that such state originates from the successive cross couplings among Fourier components of the ZF and turbulence spectra through the sideband modulation. Furthermore, it is observed that the growth rate of the global ZF is determined not only by the spectral distribution and amplitudes of turbulent pumps as usual, but also statistically by the turbulence structure, namely, their probabilistic initial phase factors. A ten-wave coupling model of the ZF modulation instability involving the essential effect of the ZF spectrum is developed to clarify the basic features of the global nonlinear ZF state.

  19. A hybrid lightwave transmission system based on light injection/optoelectronic feedback techniques and fiber-VLLC integration

    International Nuclear Information System (INIS)

    Tsai, Wen-Shing; Lu, Hai-Han; Li, Chung-Yi; Chen, Bo-Rui; Lin, Hung-Hsien; Lin, Dai-Hua

    2016-01-01

    A hybrid lightwave transmission system based on light injection/optoelectronic feedback techniques and fiber-visible laser light communication (VLLC) integration is proposed and experimentally demonstrated. To be the first one of its kind in employing light injection and optoelectronic feedback techniques in a fiber-VLLC integration lightwave transmission system, the light is successfully directly modulated with Community Access Television (CATV), 16-QAM, and 16-QAM-OFDM signals. Over a 40 km SMF and a 10 m free-space VLLC transport, good performances of carrier-to-noise ratio (CNR)/composite second-order (CSO)/composite triple-beat (CTB)/bit error rate (BER) are achieved for CATV/16-QAM/16-QAM-OFDM signals transmission. Such a hybrid lightwave transmission system would be very useful since it can provide broadband integrated services including CATV, Internet, and telecommunication services over both distribute fiber and in-building networks. (letter)

  20. Research on the application of optoelectronics to nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Shirosaki, Hidekazu; Mitsuda, Hiromichi; Kurata, Toshikazu [Institute of Nuclear Safety System Inc., Seika, Kyoto (Japan); Soramoto, Seiki; Maekawa, Tatsuyuki

    1995-09-01

    Optoelectronics, which is based on technologies such as laser diodes and optical fibers, is approaching the realm of practical application in the fields of optical fiber communications and compact disks etc,. In addition, laser enrichment, a type of uranium enrichment technique used in the nuclear field, can also be regarded as a product of optoelectronics. Application of optoelectronics in a wide range of fields is likely to continue in the future, and research is being conducted on coherent optical communication, optical integrated circuits, optical computers and other subjects in hopes of attaining practical application of these technologies in the future. On the other hand, digital control equipment and other related devices have been installed and data transfer using optical fibers has been implemented on a partial basis at nuclear power plants, and optoelectronics is anticipated to be applied on an even broader scale in the future, thereby creating the potential for improving plant reliability. In this research, we conducted an investigative study of technologies relating to optoelectronics, and proposed a remote monitoring system for manually operated valves that employs optical switches. Moreover, we conducted theoretical verification tests on the proposed system and carried out a feasibility study relating to application to nuclear power plants. As a result, the proposed system was found to be effective, and confirmed to have the potential of realization as a valve switching monitoring system. (author)

  1. Research on the application of optoelectronics to nuclear power plants

    International Nuclear Information System (INIS)

    Shirosaki, Hidekazu; Mitsuda, Hiromichi; Kurata, Toshikazu; Soramoto, Seiki; Maekawa, Tatsuyuki.

    1995-01-01

    Optoelectronics, which is based on technologies such as laser diodes and optical fibers, is approaching the realm of practical application in the fields of optical fiber communications and compact disks etc,. In addition, laser enrichment, a type of uranium enrichment technique used in the nuclear field, can also be regarded as a product of optoelectronics. Application of optoelectronics in a wide range of fields is likely to continue in the future, and research is being conducted on coherent optical communication, optical integrated circuits, optical computers and other subjects in hopes of attaining practical application of these technologies in the future. On the other hand, digital control equipment and other related devices have been installed and data transfer using optical fibers has been implemented on a partial basis at nuclear power plants, and optoelectronics is anticipated to be applied on an even broader scale in the future, thereby creating the potential for improving plant reliability. In this research, we conducted an investigative study of technologies relating to optoelectronics, and proposed a remote monitoring system for manually operated valves that employs optical switches. Moreover, we conducted theoretical verification tests on the proposed system and carried out a feasibility study relating to application to nuclear power plants. As a result, the proposed system was found to be effective, and confirmed to have the potential of realization as a valve switching monitoring system. (author)

  2. Efficient use of satellite bandwidth for shipboard science platforms

    Science.gov (United States)

    Foley, S.; Berger, J.; Orcutt, J. A.

    2012-12-01

    In its 11th year of operation, HiSeasNet, a satellite network connecting the University-National Oceanographic Laboratory System (UNOLS) fleet to the Internet, enables ships to stream sets of sensor data to shore in near-real-time, along with a variety of other ship traffic. With more ongoing and single-cruise projects wishing to use significant amounts of ship-to-shore bandwidth, efficient use of the bandwidth has become increasingly important. Incremental improvements have been made over the past few years. However, as use cases change and technology becomes more bandwidth-intensive, more work remains on both technical and behavioral levels for optimizing scientific use of satellite links.

  3. Correlation and image compression for limited-bandwidth CCD.

    Energy Technology Data Exchange (ETDEWEB)

    Thompson, Douglas G.

    2005-07-01

    As radars move to Unmanned Aerial Vehicles with limited-bandwidth data downlinks, the amount of data stored and transmitted with each image becomes more significant. This document gives the results of a study to determine the effect of lossy compression in the image magnitude and phase on Coherent Change Detection (CCD). We examine 44 lossy compression types, plus lossless zlib compression, and test each compression method with over 600 CCD image pairs. We also derive theoretical predictions for the correlation for most of these compression schemes, which compare favorably with the experimental results. We recommend image transmission formats for limited-bandwidth programs having various requirements for CCD, including programs which cannot allow performance degradation and those which have stricter bandwidth requirements at the expense of CCD performance.

  4. [Tumor segmentation of brain MRI with adaptive bandwidth mean shift].

    Science.gov (United States)

    Hou, Xiaowen; Liu, Qi

    2014-10-01

    In order to get the adaptive bandwidth of mean shift to make the tumor segmentation of brain magnetic resonance imaging (MRI) to be more accurate, we in this paper present an advanced mean shift method. Firstly, we made use of the space characteristics of brain image to eliminate the impact on segmentation of skull; and then, based on the characteristics of spatial agglomeration of different tissues of brain (includes tumor), we applied edge points to get the optimal initial mean value and the respectively adaptive bandwidth, in order to improve the accuracy of tumor segmentation. The results of experiment showed that, contrast to the fixed bandwidth mean shift method, the method in this paper could segment the tumor more accurately.

  5. High bandwidth frequency lock of a rigid tunable optical cavity.

    Science.gov (United States)

    Millo, Jacques; Merzougui, Mourad; Di Pace, Sibilla; Chaibi, Walid

    2014-11-10

    In this paper, we present a high bandwidth frequency lock of a rigid tunable Fabry Perot cavity based on a set of lead zirconate titanate (PZT) actuators. The cavity spacer was specifically designed such that the frequency of the first resonance of the whole assembly under PZT excitation is above 35 kHz, thus allowing a servo-loop bandwidth of 13 kHz. It is demonstrated that no significant noise is added by the cavity to the output beam with respect to the input beam over the servo-loop bandwidth. This cavity can be used as a pre-mode cleaner in interferometric gravitational wave detectors such as the Laser Interferometer Gravitational-Wave Observatory (LIGO) and Virgo.

  6. Estimating auditory filter bandwidth using distortion product otoacoustic emissions

    DEFF Research Database (Denmark)

    Hauen, Sigurd van; Rukjær, Andreas Harbo; Ordoñez Pizarro, Rodrigo Eduardo

    2017-01-01

    The basic frequency selectivity in the listener’s hearing is often characterized by auditory filters. These filters are determined through listening tests, which determine the masking threshold as a function of frequency of the tone and the bandwidth of the masking sound. The auditory filters have...... correlation to the theoretical relation between frequency and auditory filter bandwidth, described by the equivalent rectangular bandwidth (ERB, Glasberg and Moore, 1990). The purpose of the present study is to test if a similar correlation exists on an individual basis at normal audiometric frequencies....... The optimal 2f1-f2 (L1/L2=65/45 dB SPL). The distortion-product-otoacoustic-emission ratio is determined using a custom-made measurement system programmed in MATLAB. The auditory filters are determined using notched-noise method in a two alternative forced choice experiment with noise levels at 40 dB SPL...

  7. Constrained ℋ∞ control for low bandwidth active suspensions

    Science.gov (United States)

    Wasiwitono, Unggul; Sutantra, I. Nyoman

    2017-08-01

    Low Bandwidth Active Suspension (LBAS) is shown to be more competitive to High Bandwidth Active Suspension (HBAS) when energy and cost aspects are taken into account. In this paper, the constrained ℋ∞ control scheme is applied for LBAS system. The ℋ∞ performance is used to measure ride comfort while the concept of reachable set in a state-space ellipsoid defined by a quadratic storage function is used to capture the time domain constraint that representing the requirements for road holding, suspension deflection limitation and actuator saturation. Then, the control problem is derived in the framework of Linear Matrix Inequality (LMI) optimization. The simulation is conducted considering the road disturbance as a stationary random process. The achievable performance of LBAS is analyzed for different values of bandwidth and damping ratio.

  8. Development of a bandwidth limiting neutron chopper for CSNS

    Science.gov (United States)

    Wang, P.; Yang, B.; Cai, W. L.

    2015-08-01

    Bandwidth limiting neutron choppers are indispensable key equipments for the time-of-flight neutron scattering spectrometers of China Spallation Neutron Source (CSNS). The main principle is to chop the neutron beam to limit the neutron wavelength bandwidth at the neutron detector. We have successfully developed a bandwidth limiting neutron chopper for CSNS in the CSNS advance research project II. The transmission rate of the neutron absorbing coating is less than 1×10-4 (for 1 angstrom neutron). The phase control accuracy is ±0.084° (±9.4 μs at 25 Hz). The dynamic balance grade is G1.0. Various experimental technical features have met the design requirements, and it also runs stably and reliably during the long-term tests.

  9. Development of a bandwidth limiting neutron chopper for CSNS

    International Nuclear Information System (INIS)

    Wang, P.; Yang, B.; Cai, W.L.

    2015-01-01

    Bandwidth limiting neutron choppers are indispensable key equipments for the time-of-flight neutron scattering spectrometers of China Spallation Neutron Source (CSNS). The main principle is to chop the neutron beam to limit the neutron wavelength bandwidth at the neutron detector. We have successfully developed a bandwidth limiting neutron chopper for CSNS in the CSNS advance research project II. The transmission rate of the neutron absorbing coating is less than 1×10 −4 (for 1 angstrom neutron). The phase control accuracy is ±0.084° (±9.4 μs at 25 Hz). The dynamic balance grade is G1.0. Various experimental technical features have met the design requirements, and it also runs stably and reliably during the long-term tests

  10. Sistem Pakar Fuzzy Untuk Optimasi Penggunaan Bandwidth Jaringan Komputer

    Directory of Open Access Journals (Sweden)

    Mustaziri Mustaziri

    2014-02-01

    Full Text Available The need for bandwidth availability today is very high along with the increase of infrastructural growth of internet network. Therefore, the presence of efficient, reliable, and economical service availability system is required. It can be achieved byperforming  good  and  appropriate  system  planning.  In  providing  efficient  and  reliable  internet  services,  one  of  the supporting factors is the optimization of bandwidth using. To optimize the use of bandwidth, we use fuzzy expert system by Sugeno method. This fuzzy expert system use 3 input variables, such as lecture room, day, and t ime, with one output variable of the capacity of bandwidth used. Rule base being made based on the consultation with the expert to determine the rule base for fuzzy  system input.  The computation to determine the average error using the computation formula  of MAPE  (Means  Absolute  Percentage  Error  which  is  the  error  median  of  absolute  percentage.  The  data  of  the  research results on the optimization of bandwidth using in fuzzy expert system with Sugeno method obtain from verification, that is by comparing actual data to prediction data with fuzzy system. The average error result is 6,5142 %.Keywords: Fuzzy Expert System; Optimization; Bandwidth

  11. Optoelectronic time-domain characterization of a 100 GHz sampling oscilloscope

    International Nuclear Information System (INIS)

    Füser, H; Baaske, K; Kuhlmann, K; Judaschke, R; Pierz, K; Bieler, M; Eichstädt, S; Elster, C

    2012-01-01

    We have carried out an optoelectronic measurement of the impulse response of an ultrafast sampling oscilloscope with a nominal bandwidth of 100 GHz within a time window of approximately 100 ps. Our experimental technique also considers frequency components above the cut-off frequency of higher order modes of the 1.0 mm coaxial line, which is shown to be important for the specification of the impulse response of ultrafast sampling oscilloscopes. Additionally, we have measured the reflection coefficient of the sampling head induced by the mismatch of the sampling circuit and the coaxial connector which is larger than 0.5 for certain frequencies. The uncertainty analysis has been performed using the Monte Carlo method of Supplement 1 to the 'Guide to the Expression of Uncertainty in Measurement' and correlations in the estimated impulse response have been determined. Our measurements extend previous work which deals with the characterization of 70 GHz oscilloscopes and the measurement of 100 GHz oscilloscopes up to the cut-off frequency of higher order modes

  12. EFFECTIVE BANDWIDTH FOR SELF-SIMILAR TRAFFIC IN ATM NETWORK

    Directory of Open Access Journals (Sweden)

    Linawati Linawati

    2009-05-01

    Full Text Available This paper proposes a new approach to estimate the effective bandwidth for self-similar traffic in ATM network. In this approach we use the tail distribution of queue length based on FBM model. This approach is derived from the inequalities for Mills’ ratio. Then a comparison with Norros and Trinh&Miki schemes are analysed. The results demonstrate reasonable agreement between numerical and simulation results and between all schemes. Their bandwidth estimation tends closer for CLP improvement.

  13. Compact silicon multimode waveguide spectrometer with enhanced bandwidth

    DEFF Research Database (Denmark)

    Piels, Molly; Zibar, Darko

    2017-01-01

    Compact, broadband, and high-resolution spectrometers are appealing for sensing applications, but difficult to fabricate. Here we show using calibration data a spectrometer based on a multimode waveguide with 2 GHz resolution, 250 GHz bandwidth, and a 1.6 mm × 2.1 mm footprint. Typically......, such spectrometers have a bandwidth limited by the number of modes supported by the waveguide. In this case, an on-chip mode-exciting element is used to repeatably excite distinct collections of waveguide modes. This increases the number of independent spectral channels from the number of modes to this number...

  14. Methods and analysis of processing signals of incremental optoelectronic transducer.

    Science.gov (United States)

    Szcześniak, Adam; Szcześniak, Zbigniew

    2009-09-01

    This article is a presentation of designed methods which interpolate signals from the optoelectronic transducer. This enables a way to distinguish the motion direction of the optoelectronic transducer and also to increase its accuracy. In this article methods based on logic functions, logic functions and RC circuits, phase processing were analyzed. In methods which are based on processing logic functions of transducer's signals there is a possibility of two times and four times increase in the transducer glass scale. The presented method of generating and processing sine signals with 18 degrees of the shift enables the reception of square signals with five times higher frequency compared to the basic signals. This method is universal and it can be used to the different scale of frequency multiplication of the optoelectronic transducer. The simulations of the methods were performed by using the MATLAB-SIMULINK software.

  15. Integrated optoelectronic materials and circuits for optical interconnects

    International Nuclear Information System (INIS)

    Hutcheson, L.D.

    1988-01-01

    Conventional interconnect and switching technology is rapidly becoming a critical issue in the realization of systems using high speed silicon and GaAs based technologies. In recent years clock speeds and on-chip density for VLSI/VHSIC technology has made packaging these high speed chips extremely difficult. A strong case can be made for using optical interconnects for on-chip/on-wafer, chip-to-chip and board-to-board high speed communications. GaAs integrated optoelectronic circuits (IOC's) are being developed in a number of laboratories for performing Input/Output functions at all levels. In this paper integrated optoelectronic materials, electronics and optoelectronic devices are presented. IOC's are examined from the standpoint of what it takes to fabricate the devices and what performance can be expected

  16. History of modern optics ad optoelectronics development in China

    CERN Document Server

    Tian, Shouyun

    2014-01-01

    This book presents a collection of memoir papers on the development of modern and contemporary optics and optoelectronics in China from the 18th to 20th centuries. The papers were written by famous scientists in China, including members of the Chinese Academy of Sciences and the Chinese Academy of Engineering, sharing their experience in different fields of optics and optoelectronics development. This is a unique book in understanding the natural science history of optics and optoelectronics. It gives you the general idea about how the western optical science spread to China in the 17th to 18th century; the cradle of the contemporary optics in China; Birth, development and application of lasers in China; high energy and high power lasers for laser antiballistic missile and laser nuclear fusion; development of Chinese optical communication and optical information storage; laser and infrared optics research for space science; development of Chinese optical instruments, etc.

  17. Optoelectronic devices product assurance guideline for space application

    Science.gov (United States)

    Bensoussan, A.; Vanzi, M.

    2017-11-01

    New opportunities are emerging for the implementation of hardware sub-systems based on OptoElectronic Devices (OED) for space application. Since the end of this decade the main players for space systems namely designers and users including Industries, Agencies, Manufacturers and Laboratories are strongly demanding of adequate strategies to qualify and validate new optoelectronics products and sub-systems [1]. The long term space application mission will require to address either inter-satellite link (free space communication, positioning systems, tracking) or intra-satellite connectivity/flexibility/reconfigurability or high volume of data transfer between equipment installed into payload.

  18. High bandgap III-V alloys for high efficiency optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Alberi, Kirstin; Mascarenhas, Angelo; Wanlass, Mark

    2017-01-10

    High bandgap alloys for high efficiency optoelectronics are disclosed. An exemplary optoelectronic device may include a substrate, at least one Al.sub.1-xIn.sub.xP layer, and a step-grade buffer between the substrate and at least one Al.sub.1-xIn.sub.xP layer. The buffer may begin with a layer that is substantially lattice matched to GaAs, and may then incrementally increase the lattice constant in each sequential layer until a predetermined lattice constant of Al.sub.1-xIn.sub.xP is reached.

  19. The construction of bilingual teaching of optoelectronic technology

    Science.gov (United States)

    Zhang, Yang; Zhao, Enming; Yang, Fan; Li, Qingbo; Zhu, Zheng; Li, Cheng; Sun, Peng

    2017-08-01

    This paper combines the characteristics of optoelectronic technology with that of bilingual teaching. The course pays attention to integrating theory with practice, and cultivating learners' ability. Reform and exploration have been done in the fields of teaching materials, teaching content, teaching methods, etc. The concrete content mainly includes five parts: selecting teaching materials, establishing teaching syllabus, choosing suitable teaching method, making multimedia courseware and improving the test system, which can arouse students' interest in their study and their autonomous learning ability to provide beneficial references for improving the quality of talents of optoelectronic bilingual courses.

  20. Curriculum system for experimental teaching in optoelectronic information

    Science.gov (United States)

    Di, Hongwei; Chen, Zhenqiang; Zhang, Jun; Luo, Yunhan

    2017-08-01

    The experimental curriculum system is directly related to talent training quality. Based on the careful investigation of the developing request of the optoelectronic information talents in the new century, the experimental teaching goal and the content, the teaching goal was set to cultivate students' innovative consciousness, innovative thinking, creativity and problem solving ability. Through straightening out the correlation among the experimental teaching in the main courses, the whole structure design was phased out, as well as the hierarchical curriculum connotation. According to the ideas of "basic, comprehensive, applied and innovative", the construction of experimental teaching system called "triple-three" was put forward for the optoelectronic information experimental teaching practice.

  1. Materials and devices for silicon-based optoelectronics. Materials Research Society symposium proceedings Volume 486

    Energy Technology Data Exchange (ETDEWEB)

    Polman, A.; Coffa, S.; Soref, R.

    1998-07-01

    The field of Si-based optoelectronics is greatly expanding and attracting increased interest from the scientific community. This interest is largely motivated by the possibility of combining, on the same substrate, the excellent data-processing performances of Si-based electronic functions with the unrivaled capability of light in the transmission of information. In fact, experimental efforts have led to several breakthroughs that promise new approaches and potential commercialization of low-cost Si-based photonic devices. Physical properties and optical performance of various materials (nanocrystals, porous Si, Er-doped Si and SiGe, to mention just a few examples) are now reasonably well understood, and the requirements necessary for efficient device performances have been elucidated. The field has clearly shifted its focus from the pure engineering of materials to the use of these properties to develop and optimize novel optical devices. Experimental and theoretical contributions from academia, research laboratories and industry are presented here and highlight both the state of the art as well as future trends in this rapidly developing field. Topics include: Si-based integrated optoelectronics--state of the art and perspectives; waveguides and modulators; integrated and discrete light sources and detectors; properties and applications of silicon nanocrystals; materials for IR and visible light emission; and new materials and device concepts.

  2. Electrical and optoelectronic properties of gallium nitride

    International Nuclear Information System (INIS)

    Flannery, Lorraine Barbara

    2002-01-01

    substrates using the CARS25 RF source. The chemical concentration of Mg, [Mg] and the hole density, p H were found to increase both with layer thickness and Mg cell temperature in material grown at 700 deg C. A maximum free hole density, p H and mobility, μ H of 4.8 x 10 17 cm -3 and 10.7 cm 2 V -1 s -1 respectively were obtained for a 2.1 μm layer grown at a Mg cell temperature of 507 deg C. Photoconductive UV detectors were successfully fabricated from the highest quality n and p-type GaN layers grown by MBE on sapphire substrates. The p-type UV devices represented the first Mg doped p-type GaN based UV photoconductive detectors grown on sapphire substrates produced by the MBE growth method. The performances of both the n and p-type detectors were assessed by measurement of their optoelectronic and electrical properties and some conclusions were drawn regarding their operating principles. (author)

  3. Weiss oscillations in the electronic structure of modulated graphene

    International Nuclear Information System (INIS)

    Tahir, M; Sabeeh, K; MacKinnon, A

    2007-01-01

    We present a theoretical study of the electronic structure of modulated graphene in the presence of a perpendicular magnetic field. The density of states and the bandwidth for the Dirac electrons in this system are determined. The appearance of unusual Weiss oscillations in the bandwidth and density of states is the main focus of this work

  4. BMCloud: Minimizing Repair Bandwidth and Maintenance Cost in Cloud Storage

    Directory of Open Access Journals (Sweden)

    Chao Yin

    2013-01-01

    Full Text Available To protect data in cloud storage, fault tolerance and efficient recovery become very important. Recent studies have developed numerous solutions based on erasure code techniques to solve this problem using functional repairs. However, there are two limitations to address. The first one is consistency since the Encoding Matrix (EM is different among clouds. The other one is repairing bandwidth, which is a concern for most of us. We addressed these two problems from both theoretical and practical perspectives. We developed BMCloud, a new low repair bandwidth, low maintenance cost cloud storage system, which aims to reduce repair bandwidth and maintenance cost. The system employs both functional repair and exact repair while it inherits advantages from the both. We propose the JUDGE_STYLE algorithm, which can judge whether the system should adopt exact repair or functional repair. We implemented a networked storage system prototype and demonstrated our findings. Compared with existing solutions, BMCloud can be used in engineering to save repair bandwidth and degrade maintenance significantly.

  5. Frequency Selective Surfaces for extended Bandwidth backing reflector functions

    NARCIS (Netherlands)

    Pasian, M.; Neto, A.; Monni, S.; Ettorre, M.; Gerini, G.

    2008-01-01

    This paper deals with the use of Frequency Selective Surfaces (FSS) to increase the Efficiency × Bandwidth product in Ultra-Wide Band (UWB) antenna arrays whose efficiency is limited by the front-to-back ratio. If the backing reflector is realized in one metal plane solution its location will be

  6. Come together: African universities collaborate to improve bandwidth

    International Development Research Centre (IDRC) Digital Library (Canada)

    2011-02-02

    Feb 2, 2011 ... SEE ALSO... In Reports magazine: Viewpoint: Bandwidth can bring African universities up to speed. In Reports magazine: Brain Drain and Capacity Building in Africa · The AAU Web site. The Connectivity Africa Web site. The World Summit on the Information Society (WSIS) Web site. IDRC's ICT4D Web site ...

  7. Estimating auditory filter bandwidth using distortion product otoacoustic emissions

    DEFF Research Database (Denmark)

    Rukjær, Andreas Harbo; Hauen, Sigurd van; Ordoñez Pizarro, Rodrigo Eduardo

    2017-01-01

    The basic frequency selectivity in the listener’s hearing is often characterized by auditory filters. These filters are determined through listening tests, which estimate the masking threshold as a function of frequency of the tone and the bandwidth of the masking sound. The auditory filters have...

  8. Iterative Available Bandwidth Estimation for Mobile Transport Networks

    DEFF Research Database (Denmark)

    Ubeda Castellanos, Carlos; López Villa, Dimas; Teyeb, Oumer Mohammed

    2007-01-01

    Available bandwidth estimation has lately been proposed to be used for end-to-end resource management in existing and emerging mobile communication systems, whose transport networks could end up being the bottleneck rather than the air interface. Algorithms for admission control, handover...

  9. Sensitivity-Bandwidth Limit in a Multimode Optoelectromechanical Transducer

    Science.gov (United States)

    Moaddel Haghighi, I.; Malossi, N.; Natali, R.; Di Giuseppe, G.; Vitali, D.

    2018-03-01

    An optoelectromechanical system formed by a nanomembrane capacitively coupled to an L C resonator and to an optical interferometer has recently been employed for the highly sensitive optical readout of rf signals [T. Bagci et al., Nature (London) 507, 81 (2013), 10.1038/nature13029]. We propose and experimentally demonstrate how the bandwidth of such a transducer can be increased by controlling the interference between two electromechanical interaction pathways of a two-mode mechanical system. With a proof-of-principle device operating at room temperature, we achieve a sensitivity of 300 nV /√{Hz } over a bandwidth of 15 kHz in the presence of radio-frequency noise, and an optimal shot-noise-limited sensitivity of 10 nV /√{Hz } over a bandwidth of 5 kHz. We discuss strategies for improving the performance of the device, showing that, for the same given sensitivity, a mechanical multimode transducer can achieve a bandwidth significantly larger than that for a single-mode one.

  10. Come together: African universities collaborate to improve bandwidth

    International Development Research Centre (IDRC) Digital Library (Canada)

    2011-02-02

    Feb 2, 2011 ... However, a stumbling block to realizing this vision arose: the cost of access. As Bob Hawkins, a senior education specialist at the WBI, points out, “the average African university pays 50 times more than the amount a North American university pays for Internet access.” Moreover, the bandwidth available to ...

  11. A Practical Approach For Excess Bandwidth Distribution for EPONs

    KAUST Repository

    Elrasad, Amr

    2014-03-09

    This paper introduces a novel approach called Delayed Excess Scheduling (DES), which practically reuse the excess bandwidth in EPONs system. DES is suitable for the industrial deployment as it requires no timing constraint and achieves better performance compared to the previously reported schemes.

  12. On bounding the bandwidth of graphs with symmetry

    NARCIS (Netherlands)

    van Dam, E.R.; Sotirov, R.

    2015-01-01

    We derive a new lower bound for the bandwidth of a graph that is based on a new lower bound for the min-cut problem. Our new semidefinite programming relaxation of the min-cut problem is obtained by strengthening the known semidefinite programming relaxation for the quadratic assignment problem (or

  13. 77 FR 65713 - Certain Optoelectronic Devices for Fiber Optic Communications, Components Thereof, and Products...

    Science.gov (United States)

    2012-10-30

    ... Fiber Optic Communications, Components Thereof, and Products Containing the Same; Notice of Institution... certain optoelectronic devices for fiber optic communications, components thereof, and products containing... optoelectronic devices for fiber optic communications, components thereof, and products containing the same that...

  14. A Novel Reconfigurable OFDM Based Digital Modulator

    OpenAIRE

    Arunachalam V; Rahul Kshirsagar; Purnendu Debnath; Anand Mehta

    2013-01-01

    Digital modulation is the first step in the digital communication system (DCS). The choice of modulation scheme among BPSK, QPSK, 8-QAM and 16-QAM are made based on the performance criterion such as bit-error-rate (BER) and bandwidth (BW) utilization. Hence the operating range of the DCS is improved by incorporating all the four modulation schemes in architecture. In this paper, a reconfigurable digital modulator is proposed for OFDM based DCS with more hardware efficiency (data rate per numb...

  15. Efficient Bandwidth Management for Ethernet Passive Optical Networks

    KAUST Repository

    Elrasad, Amr Elsayed M.

    2016-05-15

    The increasing bandwidth demands in access networks motivates network operators, networking devices manufacturers, and standardization institutions to search for new approaches for access networks. These approaches should support higher bandwidth, longer distance between end user and network operator, and less energy consumption. Ethernet Passive Optical Network (EPON) is a favorable choice for broadband access networks. EPONs support transmission rates up to 10 Gbps. EPONs also support distance between end users and central office up to 20 Km. Moreover, optical networks have the least energy consumption among all types of networks. In this dissertation, we focus on reducing delay and saving energy in EPONs. Reducing delay is essential for delay-sensitive traffic, while minimizing energy consumption is an environmental necessity and also reduces the network operating costs. We identify five challenges, namely excess bandwidth allocation, frame delineation, congestion resolution, large round trip time delay in long-reach EPONs (LR-EPONs), and energy saving. We provide a Dynamic Bandwidth Allocation (DBA) approach for each challenge. We also propose a novel scheme that combines the features of the proposed approaches in one highly performing scheme. Our approach is to design novel DBA protocols that can further reduce the delay and be simultaneously simple and fair. We also present a dynamic bandwidth allocation scheme for Green EPONs taking into consideration maximizing energy saving under target delay constraints. Regarding excess bandwidth allocation, we develop an effective DBA scheme called Delayed Excess Scheduling (DES). DES achieves significant delay and jitter reduction and is more suitable for industrial deployment due to its simplicity. Utilizing DES in hybrid TDM/WDM EPONs (TWDM-EPONs) is also investigated. We also study eliminating the wasted bandwidth due to frame delineation. We develop an interactive DBA scheme, Efficient Grant Sizing Interleaved

  16. Pump-to-Signal Intensity Modulation Transfer in Saturated- Gain Fiber Optical Parametric Amplifiers

    DEFF Research Database (Denmark)

    Lali-Dastjerdi, Zohreh; Lund-Hansen, Toke; Rottwitt, Karsten

    2011-01-01

    The pump-to-signal intensity modulation transfer in saturated degenerate FOPAs is numerically investigated over the whole gain bandwidth. The intensity modulation transfer decreases and the OSNR improves when the amplifier operates in the saturation regime....

  17. Numerical investigation of the self-focusing of broad-bandwidth laser light with applied angular dispersion

    Science.gov (United States)

    McKenty, P. W.; Skupsky, S.; Kelly, J. H.; Cotton, C. T.

    1994-08-01

    The self-focusing of phase-modulated broad-bandwidth (BBW) laser light, in which the spectral components are angularly dispersed to produce smoothing of laser nonuniformities, is analyzed. A multifrequency, multidimensional computer code has been developed to simulate the propagation of angularly dispersed BBW light within a nonlinear medium. Earlier work has shown that the self-focusing behavior of phase-modulated BBW light without angular dispersion is insignificantly different from that of monochromatic beams. With the addition of angular dispersion, pure phase modulation cannot be maintained during propagation, and the beam becomes subject to the development of spatial amplitude modulation which moves across the beam in time. Instantaneously, this amplitude modulation will begin to self-focus in a nonlinear medium. However, when examined over one period of the phase modulation, the time-integrated intensity (TII) due to the angularly dispersed BBW beam is consistently smooth, regardless of the amount of propagation modulation or self-focusing growth present in the instantaneous profile. Similarly, the angular dispersion will produce a time-dependent deflection of any amplitude modulation on the beam produced by laser defects. Because the focus of the modulation is enlarged due to the deflection, the TII of this amplitude structure is found to be less than that for a monochromatic beam.

  18. Opto-electronic properties of charged conjugated molecules

    NARCIS (Netherlands)

    Fratiloiu, S.

    2007-01-01

    The aim of this thesis is to provide fundamental insight into the nature and opto-electronic properties of charge carriers on conjugated oligomers and polymers. Electronic structure, optical absorption properties and distribution of charge carriers along the chains of different conjugated materials

  19. Advances in wide bandgap SiC for optoelectronics

    DEFF Research Database (Denmark)

    Ou, Haiyan; Ou, Yiyu; Argyraki, Aikaterini

    2014-01-01

    Silicon carbide (SiC) has played a key role in power electronics thanks to its unique physical properties like wide bandgap, high breakdown field, etc. During the past decade, SiC is also becoming more and more active in optoelectronics thanks to the progress in materials growth and nanofabrication...

  20. Opto-electronics on Single Nanowire Quantum Dots

    NARCIS (Netherlands)

    Van Kouwen, M.P.

    2010-01-01

    An important goal for nanoscale opto-electronics is the transfer of single electron spin states into single photon polarization states (and vice versa), thereby interfacing quantum transport and quantum optics. Such an interface enables new experiments in the field of quantum information processing.

  1. Poly(organylsilylene)s - perspective materials for optoelectronics

    Czech Academy of Sciences Publication Activity Database

    Nešpůrek, Stanislav

    1999-01-01

    Roč. 49, č. 5 (1999), s. 859-870 ISSN 0011-4626. [Czech-Chinese Workshop Advanced Materials for Optoelectronics . Prague, 13.06.1998-17.06.1998] R&D Projects: GA ČR GA106/98/0700 Subject RIV: CD - Macromolecular Chemistry Impact factor: 0.328, year: 1999

  2. Large-signal modulation characteristics of a GaN-based micro-LED for Gbps visible-light communication

    Science.gov (United States)

    Tian, Pengfei; Wu, Zhengyuan; Liu, Xiaoyan; Fang, Zhilai; Zhang, Shuailong; Zhou, Xiaolin; Liu, Kefu; Liu, Ming-Gang; Chen, Shu-Jhih; Lee, Chia-Yu; Cong, Chunxiao; Hu, Laigui; Qiu, Zhi-Jun; Zheng, Lirong; Liu, Ran

    2018-04-01

    The large-signal modulation characteristics of a GaN-based micro-LED have been studied for Gbps visible-light communication. With an increasing signal modulation depth the modulation bandwidth decreases, which matches up with the increase in the sum of the signal rise time and fall time. By simulating the band diagram and the carrier recombination rate of the micro-LED under large-signal modulation, carrier recombination and the carrier sweep-out effect are analyzed and found to be the dominant mechanisms behind the variation of modulation bandwidth. These results give further insight into improving the modulation bandwidth for high-speed visible-light communication.

  3. Power allocation, bit loading and sub-carrier bandwidth sizing for OFDM-based cognitive radio

    Directory of Open Access Journals (Sweden)

    Desai Uday

    2011-01-01

    Full Text Available Abstract The function of the Radio Resource Management module of a Cognitive Radio (CR system is to evaluate the available resources and assign them to meet the Quality of Service (QoS objectives of the Secondary User (SU, within some constraints on factors which limit the performance of the Primary User (PU. While interference mitigation to the PU spectral band from the SU's transmission has received a lot of attention in recent literature; the novelty of our work is in considering a more realistic and effective approach of dividing the PU into sub-bands, and ensuring that the interference to each of them is below a specified threshold. With this objective, and within a power budget, we execute the tasks of power allocation, bit loading and sizing the sub-carrier bandwidth for an orthogonal frequency division multiplexing (OFDM-based SU. After extensively analyzing the solution form of the optimization problems posed for the resource allocation, we suggest iterative algorithms to meet the aforementioned objectives. The algorithm for sub-carrier bandwidth sizing is novel, and not previously presented in literature. A multiple SU scenario is also considered, which entails assigning sub-carriers to the users, besides the resource allocation. Simulation results are provided, for both single and multi-user cases, which indicate the effectiveness of the proposed algorithms in a CR environment.

  4. Sidemode suppression for coupled optoelectronic oscillator by optical pulse power feedforward.

    Science.gov (United States)

    Dai, Yitang; Wang, Ruixin; Yin, Feifei; Dai, Jian; Yu, Lan; Li, Jianqiang; Xu, Kun

    2015-10-19

    Multiple sidemodes have been observed in a coupled optoelectronic oscillator (COEO) when the contained actively mode-locked fiber ring laser employs erbium-doped fiber (EDF). We propose that such sidemodes can be suppressed significantly by an optical pulse power feedforward scheme, through which the mode-locked optical pulse is reversely intensity-modulated by itself, resulting in a fast power limiting. Experimentally we show that sidemodes are suppressed as much as 40 dB in a 10-GHz COEO. The additional noise induced by the power feedforward technique is analyzed numerically. We show that for a COEO with a typical cavity length, the feedforward contribution to final single-side band (SSB) noise is minor and neglectable.

  5. Molecular beam epitaxy growth of Al-rich AlGaN nanowires for deep ultraviolet optoelectronics

    Directory of Open Access Journals (Sweden)

    S. Zhao

    2016-08-01

    Full Text Available Self-organized AlGaN nanowires by molecular beam epitaxy have attracted significant attention for deep ultraviolet optoelectronics. However, due to the strong compositional modulations under conventional nitrogen rich growth conditions, emission wavelengths less than 250 nm have remained inaccessible. Here we show that Al-rich AlGaN nanowires with much improved compositional uniformity can be achieved in a new growth paradigm, wherein a precise control on the optical bandgap of ternary AlGaN nanowires can be achieved by varying the substrate temperature. AlGaN nanowire LEDs, with emission wavelengths spanning from 236 to 280 nm, are also demonstrated.

  6. Bandwidth-enhanced photopolymer waveguide hologram-based optical backplane

    Science.gov (United States)

    Bi, Hai; Tian, Chuhua; Chen, Ray T.; Han, Xuliang

    2005-01-01

    As multiprocessing comes into the mainstream, the board-to-board interconnects become even more critical. In a shared-memory multiprocessing system, the shared bus topology is the preferred interconnect scheme because its broadcast nature can be effectively utilized to reduce communication latency, lessen networking complexity, and support cache coherence. In the electrical domain, however, a major performance bottleneck is anticipated due to the restricted bus bandwidth. In this paper, an innovative architecture, optical centralized shared bus, is proposed for use in the multiprocessing systems. This architecture utilizes the terascale bandwidth capacity of substrate-guided optical interconnects, while at the same time, retaining the essential merits of the shared bus topology. Thus, a smooth migration with substantial multiprocessing performance improvement is expected. A conceptual emulation of the shared-memory multiprocessing scheme is demonstrated on a generic PCI subsystem with an optical centralized shared bus. The objective of this effort is to prove the technical feasibility from the architecture standpoint.

  7. Systems with selective overflow and change of bandwidth

    DEFF Research Database (Denmark)

    Iversen, Villy Bæk

    2012-01-01

    We consider a loss system with n channels and a finite or infinite overflow group, which is offered N different services, all having Poisson arrival processes. All calls have same bandwidth demand and mean service time, but the mean service time may be different on the primary group and the overf......We consider a loss system with n channels and a finite or infinite overflow group, which is offered N different services, all having Poisson arrival processes. All calls have same bandwidth demand and mean service time, but the mean service time may be different on the primary group...... on the overflow group, we show by balance equations that the number of calls of each service will be Multinomial distributed with probabilities proportional with the arrival rates. Using a recent result of Newcomer & al, we then find moments (done up to fourth order) of individual overflow streams or any...

  8. Bandwidth-sharing in LHCONE, an analysis of the problem

    Science.gov (United States)

    Wildish, T.

    2015-12-01

    The LHC experiments have traditionally regarded the network as an unreliable resource, one which was expected to be a major source of errors and inefficiency at the time their original computing models were derived. Now, however, the network is seen as much more capable and reliable. Data are routinely transferred with high efficiency and low latency to wherever computing or storage resources are available to use or manage them. Although there was sufficient network bandwidth for the experiments’ needs during Run-1, they cannot rely on ever-increasing bandwidth as a solution to their data-transfer needs in the future. Sooner or later they need to consider the network as a finite resource that they interact with to manage their traffic, in much the same way as they manage their use of disk and CPU resources. There are several possible ways for the experiments to integrate management of the network in their software stacks, such as the use of virtual circuits with hard bandwidth guarantees or soft real-time flow-control, with somewhat less firm guarantees. Abstractly, these can all be considered as the users (the experiments, or groups of users within the experiment) expressing a request for a given bandwidth between two points for a given duration of time. The network fabric then grants some allocation to each user, dependent on the sum of all requests and the sum of available resources, and attempts to ensure the requirements are met (either deterministically or statistically). An unresolved question at this time is how to convert the users’ requests into an allocation. Simply put, how do we decide what fraction of a network's bandwidth to allocate to each user when the sum of requests exceeds the available bandwidth? The usual problems of any resourcescheduling system arise here, namely how to ensure the resource is used efficiently and fairly, while still satisfying the needs of the users. Simply fixing quotas on network paths for each user is likely to lead

  9. The Bandwidths of a Matrix. A Survey of Algorithms

    Directory of Open Access Journals (Sweden)

    Mafteiu-Scai Liviu Octavian

    2014-12-01

    Full Text Available The bandwidth, average bandwidth, envelope, profile and antibandwidth of the matrices have been the subjects of study for at least 45 years. These problems have generated considerable interest over the years because of them practical relevance in areas like: solving the system of equations, finite element methods, circuit design, hypertext layout, chemical kinetics, numerical geophysics etc. In this paper a brief description of these problems are made in terms of their definitions, followed by a comparative study of them, using both approaches: matrix geometry and graph theory. Time evolution of the corresponding algorithms as well as a short description of them are made. The work also contains concrete real applications for which a large part of presented algorithms were developed.

  10. ±25ppm repeatable measurement of trapezoidal pulses with 5MHz bandwidth

    CERN Document Server

    AUTHOR|(SzGeCERN)712364; Arpaia, Pasquale; Cerqueira Bastos, Miguel; Martino, Michele

    2015-01-01

    High-quality measurements of pulses are nowadays widely used in fields such as radars, pulsed lasers, electromagnetic pulse generators, and particle accelerators. Whilst literature is mainly focused on fast systems for nanosecond regime with relaxed metrological requirements, in this paper, the high-performance measurement of slower pulses in microsecond regime is faced. In particular, the experimental proof demonstration for a 15 MS/s,_25 ppm repeatable acquisition system to characterize the flat-top of 3 ms rise-time trapezoidal pulses is given. The system exploits a 5MHz bandwidth circuit for analogue signal processing based on the concept of flat-top removal. The requirements, as well as the conceptual and physical designs are illustrated. Simulation results aimed at assessing the circuit performance are also presented. Finally, an experimental case study on the characterization of a pulsed power supply for the klystrons modulators of the Compact Linear Collider (CLIC) under study at CERN is reported. In ...

  11. Exploration on the training mode of application-oriented talents majoring in optoelectronic information

    Science.gov (United States)

    Lv, Hao; Liu, Aimei; Zhang, Shengyi; Xiao, Yongjun

    2017-08-01

    The optoelectronic information major is a strong theoretical and practical specialty. In view of the problems existing in the application-oriented talents training in the optoelectronic information specialty. Five aspects of the talent cultivation plan, the teaching staff, the teaching content, the practical teaching and the scientific research on the training mode of application-oriented talents majoring in optoelectronic information are putted forward. It is beneficial to the specialty construction of optoelectronic information industry which become close to the development of enterprises, and the depth of the integration of school and enterprise service regional economic optoelectronic information high-end skilled personnel base.

  12. Bandwidth improvement for germanium photodetector using wire bonding technology.

    Science.gov (United States)

    Chen, Guanyu; Yu, Yu; Deng, Shupeng; Liu, Lei; Zhang, Xinliang

    2015-10-05

    We demonstrate an ultrahigh speed germanium photodetector by introducing gold wires into the discrete ground electrodes with standard wire bonding technology. To engineer the parasitic parameter, the physical dimension of the gold wire used for wire bonding is specially designed with an inductance of about 450 pH. Simulation and experimental results show that the bandwidth of the photodetector can be effectively extended from less than 30 GHz to over 60 GHz.

  13. Bandwidth Management in Wireless Home Networks for IPTV Solutions

    Directory of Open Access Journals (Sweden)

    Tamás Jursonovics

    2013-01-01

    Full Text Available The optimal allocation of the retransmission bandwidth is essential for IPTV service providers to ensure maximal service quality. This paper highlights the relevance of the wireless transport in today’s IPTV solution and discusses how this new media affects the existing broadcast technologies. A new Markovian channel model is developed to address the optimization issues of the retransmission throughput, and a new method is presented which is evaluated by empirical measurements followed by mathematical analysis.

  14. Designing large-bandwidth planar photonic crystal waveguides

    DEFF Research Database (Denmark)

    Lavrinenko, Andrei; Søndergaard, Thomas

    2002-01-01

    Our waveguide design is characterized by first of all a large bandwidth, and secondly it is characterized by a relatively high group velocity giving a better modal dispersion match with the modes of standard waveguides used for coupling light into the planar crystal waveguide (PCW). We consider t...... the dispersion properties for a PCW based on introducing a line defect in a photonic crystal with air-holes arranged periodically on a triangular lattice in silicon....

  15. T0001 / MilliNewton force sensor / frequency bandwidth

    OpenAIRE

    Maeder, Thomas

    2014-01-01

    This document gives an approximate calculation of the frequency bandwidth of the MilliNewton – and serves as a starting point for calculations on other cantilever-type sensors. The mechanical resonance frequencies of MilliNewton are high, due to the very small cantilever size. The working frequency is in fact limited by the electrical circuit at ca. 1 kHz (MilliNewton-A) or ca. 200 Hz (MilliNewton-B).

  16. Development of Information Assurance Protocol for Low Bandwidth Nanosatellite Communications

    Science.gov (United States)

    2017-09-01

    encryption method may be the fastest most reliable encryption method for nanosatellites. Utilizing Python as a development and testing platform for the...immediately by the state of health data. F. NERDP PROOF OF CONCEPT PLATFORM DEVELOPMENT In order to test the validity of the design of NERDP, a proof of...bandwidth reliable network protocol that can support a cryptographic system for encrypted communications using commercial off-the-shelf components

  17. iGrid2002 Demonstration: Bandwidth from the Low Lands

    Energy Technology Data Exchange (ETDEWEB)

    Cottrell, Les

    2002-11-01

    We report on a demonstration of several complementary high performance end-to-end active network throughput measurement tools. These include: the PingWorld Java applet that displays the Round Trip Time (RTT) and losses to sites around the world from the user's host; the multi-path analysis tool that visualizes common paths from traceroutes to selected hosts; the IEPM high-performance BandWidth monitoring toolkit which gives achievable throughput for several types of TCP data transfer applications; and the Available Bandwidth Estimation (ABWE) tool that reports in real time the available bandwidth to several paths within the range from Mbits/s to Gbit/s. We also demonstrated sending high-speed data from 4 hosts at iGrid2002 to over 30 hosts in 10 countries to simulate a high energy physics experiment distributing data to collaborators. The demonstration utilized the high-speed, long latency, trans-Atlantic network set up for iGrid2002 in Amsterdam during September 2002.

  18. Large-bandwidth data acquisition network for XFEL facility, SACLA

    International Nuclear Information System (INIS)

    Sugimoto, T.; Joti, Y.; Ohata, T.; Tanaka, R.; Yamaga, M.; Hatsui, T.

    2012-01-01

    The SACLA (SPring-8 Angstrom Compact Free Electron Laser) facility consists of an accelerator building, an undulator building and an experimental facility. SACLA is designed to produce X-ray with a wavelength as short as 0.06 nm and with a repetition rate of 60 Hz. X-ray Free-Electron Laser (XFEL) experiments demands large bandwidth network for data acquisition (DAQ). At SACLA the experimental data rate is to be up to 5.8 Giga bit per second (Gbps). Some of the experiments demands preprocessing and on-line analysis by high-performance computers. In order to fulfill these requirements, a dedicated network system for DAQ and data analysis has been developed. A DAQ network consists of a dedicated 10 Gbps Ethernet (10 GbE) physical layer to secure the data bandwidth and a 1 GbE layer for instrument controls. The DAQ network is connected to a primary storage and indirectly to a PC cluster for data preprocessing. A fire-wall system with virtual private network (VPN) features is also implemented in order to secure remote access from off-site institutes. The use of a large-bandwidth data transfer technique allows the efficient transfer of pre-processed data from SACLA to an off-site supercomputer

  19. Neural bandwidth of veridical perception across the visual field

    Science.gov (United States)

    Wilkinson, Michael O.; Anderson, Roger S.; Bradley, Arthur; Thibos, Larry N.

    2016-01-01

    Neural undersampling of the retinal image limits the range of spatial frequencies that can be represented veridically by the array of retinal ganglion cells conveying visual information from eye to brain. Our goal was to demarcate the neural bandwidth and local anisotropy of veridical perception, unencumbered by optical imperfections of the eye, and to test competing hypotheses that might account for the results. Using monochromatic interference fringes to stimulate the retina with high-contrast sinusoidal gratings, we measured sampling-limited visual resolution along eight meridians from 0° to 50° of eccentricity. The resulting isoacuity contour maps revealed all of the expected features of the human array of retinal ganglion cells. Contours in the radial fringe maps are elongated horizontally, revealing the functional equivalent of the anatomical visual streak, and are extended into nasal retina and superior retina, indicating higher resolution along those meridians. Contours are larger in diameter for radial gratings compared to tangential or oblique gratings, indicating local anisotropy with highest bandwidth for radially oriented gratings. Comparison of these results to anatomical predictions indicates acuity is proportional to the sampling density of retinal ganglion cells everywhere in the retina. These results support the long-standing hypothesis that “pixel density” of the discrete neural image carried by the human optic nerve limits the spatial bandwidth of veridical perception at all retinal locations. PMID:26824638

  20. Managing high-bandwidth real-time data storage

    Energy Technology Data Exchange (ETDEWEB)

    Bigelow, David D. [Los Alamos National Laboratory; Brandt, Scott A [Los Alamos National Laboratory; Bent, John M [Los Alamos National Laboratory; Chen, Hsing-Bung [Los Alamos National Laboratory

    2009-09-23

    There exist certain systems which generate real-time data at high bandwidth, but do not necessarily require the long-term retention of that data in normal conditions. In some cases, the data may not actually be useful, and in others, there may be too much data to permanently retain in long-term storage whether it is useful or not. However, certain portions of the data may be identified as being vitally important from time to time, and must therefore be retained for further analysis or permanent storage without interrupting the ongoing collection of new data. We have developed a system, Mahanaxar, intended to address this problem. It provides quality of service guarantees for incoming real-time data streams and simultaneous access to already-recorded data on a best-effort basis utilizing any spare bandwidth. It has built in mechanisms for reliability and indexing, can scale upwards to meet increasing bandwidth requirements, and handles both small and large data elements equally well. We will show that a prototype version of this system provides better performance than a flat file (traditional filesystem) based version, particularly with regard to quality of service guarantees and hard real-time requirements.

  1. Quantum gates with optimal bandwidth in noisy environments

    Science.gov (United States)

    Low, Guang Hao; Theodore, Yoder; Chuang, Isaac

    The traditional approach of open-loop quantum error correction suppresses certain systematic imperfections ɛ in quantum control to higher orders ɛ  (L) by a well-designed sequence of L imperfect quantum gates. However, this philosophy of maximal flatness leads to an ɛ-bandwidth that scales poorly with length and a residual that is easily overwhelmed by unaccounted sources of noise. We advance the paradigm of equiripple compensated gates that directly optimize for bandwidth given the limitations imposed by noise of magnitude δ, leading to dramatically improved performance. Where ɛ represent amplitude errors, we provide a formalism that generalizes both approaches and is effective at finding such gates. With it, we provide in closed-form the phase angles for an optimal family of population inversion gates with an ɛ -bandwidth of  (logδ-1/L) - a quadratic improvement over optimal maximally flat variants. We also construct optimal NOT gates and discuss extensions to other gates and error models.

  2. Enhanced all-optical modulation in a graphene-coated fibre with low insertion loss.

    Science.gov (United States)

    Zhang, Haojie; Healy, Noel; Shen, Li; Huang, Chung Che; Hewak, Daniel W; Peacock, Anna C

    2016-03-22

    Graphene is a highly versatile two-dimensional material platform that offers exceptional optical and electrical properties. Of these, its dynamic conductivity and low effective carrier mass are of particular interest for optoelectronic applications as they underpin the material's broadband nonlinear optical absorption and ultra-fast carrier mobility, respectively. In this paper, we utilize these phenomena to demonstrate a high-speed, in-fibre optical modulator developed on a side-polished optical fibre platform. An especially low insertion loss (fibre to a near atomically smooth surface (fibre. In order to enhance the light-matter interaction, the graphene film is coated with a high index polyvinyl butyral layer, which has the added advantage of acting as a barrier to the surrounding environment. Using this innovative approach, we have fabricated a robust and stable all-fibre device with an extinction ratio as high as 9 dB and operation bandwidth of 0.5 THz. These results represent a key step towards the integration of low-dimensional materials within standard telecoms networks.

  3. Micro-optical components assembly for the fabrication of a miniaturized optoelectronic transducer

    Science.gov (United States)

    Corradi, P.; Ascari, L.; Menciassi, A.; Laschi, C.

    2007-10-01

    This paper describes the fabrication and, in particular, the assembly processes of a miniaturized micro-optical system, to be integrated on a hybrid flexible module, which hosts also electronics and microsensors. The whole module was conceived to be mass-produced in order to be distributed in skin-like structures for robotic tactile applications. Nevertheless, it is generally suitable for sensing applications where the flexibility and the thickness of the sensing network are primary requirements. The micro-optical system works as a part of an optoelectronic transducer where electric signals, generated by tactile MEMS sensors, are computed by a microcontroller that drives the micro-optical system. This consequently generates optical radiation, by means of integrated light emitting diodes (LEDs), to be coupled into optical fibers, which waveguide signals to a CMOS optical sensor. Micro-machining and micro-assembly processes of miniaturized components are critical steps in order to fabricate many of these modules according to the application requirements.

  4. Combined Coding And Modulation Using Runlength Limited Error ...

    African Journals Online (AJOL)

    In this paper we propose a Combined Coding and Modulation (CCM) scheme employing RLL/ECCs and MPSK modulation as well as RLL/ECC codes and BFSK/MPSK modulation with a view to optimise on channel bandwidth. The CCM codes and their trellis are designed and their error performances simulated in AWGN ...

  5. Analysis of small-signal intensity modulation of semiconductor ...

    Indian Academy of Sciences (India)

    This paper demonstrates theoretical characterization of intensity modulation of semiconductor lasers (SL's). The study is based on a small-signal model to solve the laser rate equations taking into account suppression of optical gain. Analytical forms of the small-signal modulation response and modulation bandwidth are ...

  6. Recent advances in flexible and wearable organic optoelectronic devices

    Science.gov (United States)

    Zhu, Hong; Shen, Yang; Li, Yanqing; Tang, Jianxin

    2018-01-01

    Flexible and wearable optoelectronic devices have been developing to a new stage due to their unique capacity for the possibility of a variety of wearable intelligent electronics, including bendable smartphones, foldable touch screens and antennas, paper-like displays, and curved and flexible solid-state lighting devices. Before extensive commercial applications, some issues still have to be solved for flexible and wearable optoelectronic devices. In this regard, this review concludes the newly emerging flexible substrate materials, transparent conductive electrodes, device architectures and light manipulation methods. Examples of these components applied for various kinds of devices are also summarized. Finally, perspectives about the bright future of flexible and wearable electronic devices are proposed. Project supported by the Ministry of Science and Technology of China (No. 2016YFB0400700).

  7. Widrow-cellular neural network and optoelectronic implementation

    Science.gov (United States)

    Bal, Abdullah

    A new type of optoelectronic cellular neural network has been developed by providing the capability of coefficients adjusment of cellular neural network (CNN) using Widrow based perceptron learning algorithm. The new supervised cellular neural network is called Widrow-CNN. Despite the unsupervised CNN, the proposed learning algorithm allows to use the Widrow-CNN for various image processing applications easily. Also, the capability of CNN for image processing and feature extraction has been improved using basic joint transform correlation architecture. This hardware application presents high speed processing capability compared to digital applications. The optoelectronic Widrow-CNN has been tested for classic CNN feature extraction problems. It yields the best results even in case of hard feature extraction problems such as diagonal line detection and vertical line determination.

  8. Low-Dimensional Nano structures for Optoelectronic Applications

    International Nuclear Information System (INIS)

    Lei, W.; Faraone, L.; Hoe Tan, H.; Lu, W.

    2014-01-01

    In recent years, low-dimensional (zero-, one-, and two-dimensional) nano structures have attracted wide attention and become a focus of scientific research and engineering application. This is due to their novel physical and chemical properties caused by size and quantum effects, as well as potential applications in various kinds of devices, for example, optoelectronics, nano electronics, and so forth. This special issue is intended to bring the most recent advances in the field of low-dimensional nano structures for optoelectronic applications. As expected, the research articles in this special issue cover a wide range of topics in this research field, ranging from theoretical simulation to material synthesis, to material characterization, to device fabrication, and to device characterization

  9. Integrated Optoelectronic Networks for Application-Driven Multicore Computing

    Science.gov (United States)

    2017-05-08

    AFRL-AFOSR-VA-TR-2017-0102 Integrated Optoelectronic Networks for Application- Driven Multicore Computing Sudeep Pasricha COLORADO STATE UNIVERSITY...601 S HOWES ST FORT COLINS, CO 805212807 05/08/2017 Final Report DISTRIBUTION A: Distribution approved for public release. Air Force Research...Laboratory AF Office Of Scientific Research (AFOSR)/RTA1 5/25/2017https://livelink.ebs.afrl.af.mil/livelink/llisapi.dll a. REPORT Unclassified b. ABSTRACT

  10. Quantum Transport and Optoelectronics in Gapped Graphene Nanodevices

    Science.gov (United States)

    2016-11-30

    heat , while energy retained in the electronic subsystem can be used to drive an optoelectronic circuit. In graphene, energy relaxation pathways are...underlying mechanism was under debate between the photovoltaic (PV) effect, where the photogenerated electron-hole pairs are separated by a built-in...challenging to detect and control the thermalization process in graphene, or more generally, in any solid-state systems . We take a novel approach to

  11. Opto-electronics on Single Nanowire Quantum Dots

    OpenAIRE

    Van Kouwen, M.P.

    2010-01-01

    An important goal for nanoscale opto-electronics is the transfer of single electron spin states into single photon polarization states (and vice versa), thereby interfacing quantum transport and quantum optics. Such an interface enables new experiments in the field of quantum information processing. Single and entangled photon-pair generation can be used for quantum cryptography. Furthermore, photons can be used in the readout of a quantum computer based on electron spins. Semiconducting nano...

  12. The Cellulose Nanofibers for Optoelectronic Conversion and Energy Storage

    Directory of Open Access Journals (Sweden)

    Yongfeng Luo

    2014-01-01

    Full Text Available Cellulose widely exists in plant tissues. Due to the large pores between the cellulose units, the regular paper is nontransparent that cannot be used in the optoelectronic devices. But some chemical and physical methods such as 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO oxidation can be used to improve the pores scale between the cellulose units to reach nanometer level. The cellulose nanofibers (CNFs have good mechanical strength, flexibility, thermostability, and low thermal expansion. The paper made of these nanofibers represent a kind of novel nanostructured material with ultrahigh transparency, ultrahigh haze, conductivity, biodegradable, reproducible, low pollution, environment friendly and so on. These advantages make the novel nanostructured paper apply in the optoelectronic device possible, such as electronics energy storage devices. This kind of paper is considered most likely to replace traditional materials like plastics and glass, which is attracting widespread attention, and the related research has also been reported. The purpose of this paper is to review CNFs which are applied in optoelectronic conversion and energy storage.

  13. Low -Dimensional Halide Perovskites and Their Advanced Optoelectronic Applications

    Science.gov (United States)

    Zhang, Jian; Yang, Xiaokun; Deng, Hui; Qiao, Keke; Farooq, Umar; Ishaq, Muhammad; Yi, Fei; Liu, Huan; Tang, Jiang; Song, Haisheng

    2017-07-01

    Metal halide perovskites are crystalline materials originally developed out of scientific curiosity. They have shown great potential as active materials in optoelectronic applications. In the last 6 years, their certified photovoltaic efficiencies have reached 22.1%. Compared to bulk halide perovskites, low-dimensional ones exhibited novel physical properties. The photoluminescence quantum yields of perovskite quantum dots are close to 100%. The external quantum efficiencies and current efficiencies of perovskite quantum dot light-emitting diodes have reached 8% and 43 cd A-1, respectively, and their nanowire lasers show ultralow-threshold room-temperature lasing with emission tunability and ease of synthesis. Perovskite nanowire photodetectors reached a responsivity of 10 A W-1 and a specific normalized detectivity of the order of 1012 Jones. Different from most reported reviews focusing on photovoltaic applications, we summarize the rapid progress in the study of low-dimensional perovskite materials, as well as their promising applications in optoelectronic devices. In particular, we review the wide tunability of fabrication methods and the state-of-the-art research outputs of low-dimensional perovskite optoelectronic devices. Finally, the anticipated challenges and potential for this exciting research are proposed.

  14. Optoelectronics-related competence building in Japanese and Western firms

    Science.gov (United States)

    Miyazaki, Kumiko

    1992-05-01

    In this paper, an analysis is made of how different firms in Japan and the West have developed competence related to optoelectronics on the basis of their previous experience and corporate strategies. The sample consists of a set of seven Japanese and four Western firms in the industrial, consumer electronics and materials sectors. Optoelectronics is divided into subfields including optical communications systems, optical fibers, optoelectronic key components, liquid crystal displays, optical disks, and others. The relative strengths and weaknesses of companies in the various subfields are determined using the INSPEC database, from 1976 to 1989. Parallel data are analyzed using OTAF U.S. patent statistics and the two sets of data are compared. The statistical analysis from the database is summarized for firms in each subfield in the form of an intra-firm technology index (IFTI), a new technique introduced to assess the revealed technology advantage of firms. The quantitative evaluation is complemented by results from intensive interviews with the management and scientists of the firms involved. The findings show that there is a marked variation in the way firms' technological trajectories have evolved giving rise to strength in some and weakness in other subfields for the different companies, which are related to their accumulated core competencies, previous core business activities, organizational, marketing, and competitive factors.

  15. Nuclear physics and optoelectronics presence in industry, medicine and environment

    International Nuclear Information System (INIS)

    Robu, Maria; Peteu, Gh.

    2000-01-01

    This paper reveals applications of Nuclear Physics and Optoelectronics in numerous fields of interest in industry, medicine, environment. In the first part of the work basic elements are analyzed, among which: - the large possibilities offered by the investigation, analysis and testing techniques based on nuclear physics and optoelectronics; - the superior qualitative and quantitative characteristics of these techniques, with varied applicability in fields from industry, medicine and environment. These applications refers to: - elemental analyses of content and impurities; - non-destructive testing with X and gamma radiations; - investigations with radioactive and activable tracers in trophic chains as for instance, ground-vegetation-products-consumers-environment, including also the systemic pollution factors; - complex investigations in the interface tritium-vegetation-environment-humans; - techniques and radiopharmaceutical products for medical investigations; - determinations and automatic control for levels, density, thickness, humidity, surfaces covering; - monitoring by means of remote sensing for the evaluation of the environment, vegetation and pollution factors; - applications and production of laser and UV installations; - connections through optical fibres resistant to radiations; - imaging and medical bioengineering; - advances in X ray, laser and ultrasonic radiology; - monitoring with radiations beams. In the final part, there are presented examples of optoelectronics and nuclear physics applications in fields in industry, medicine and environment, with special stress on their basic characteristics and efficiency. (authors)

  16. Web-Enabled Optoelectronic Particle-Fallout Monitor

    Science.gov (United States)

    Lineberger, Lewis P.

    2008-01-01

    A Web-enabled optoelectronic particle- fallout monitor has been developed as a prototype of future such instruments that (l) would be installed in multiple locations for which assurance of cleanliness is required and (2) could be interrogated and controlled in nearly real time by multiple remote users. Like prior particle-fallout monitors, this instrument provides a measure of particles that accumulate on a surface as an indication of the quantity of airborne particulate contaminants. The design of this instrument reflects requirements to: Reduce the cost and complexity of its optoelectronic sensory subsystem relative to those of prior optoelectronic particle fallout monitors while maintaining or improving capabilities; Use existing network and office computers for distributed display and control; Derive electric power for the instrument from a computer network, a wall outlet, or a battery; Provide for Web-based retrieval and analysis of measurement data and of a file containing such ancillary data as a log of command attempts at remote units; and Use the User Datagram Protocol (UDP) for maximum performance and minimal network overhead.

  17. Broadband optical modulators based on graphene supercapacitors.

    Science.gov (United States)

    Polat, Emre O; Kocabas, Coskun

    2013-01-01

    Optical modulators are commonly used in communication and information technology to control intensity, phase, or polarization of light. Electro-optic, electroabsorption, and acousto-optic modulators based on semiconductors and compound semiconductors have been used to control the intensity of light. Because of gate tunable optical properties, graphene introduces new potentials for optical modulators. The operation wavelength of graphene-based modulators, however, is limited to infrared wavelengths due to inefficient gating schemes. Here, we report a broadband optical modulator based on graphene supercapacitors formed by graphene electrodes and electrolyte medium. The transparent supercapacitor structure allows us to modulate optical transmission over a broad range of wavelengths from 450 nm to 2 μm under ambient conditions. We also provide various device geometries including multilayer graphene electrodes and reflection type device geometries that provide modulation of 35%. The graphene supercapacitor structure together with the high-modulation efficiency can enable various active devices ranging from plasmonics to optoelectronics.

  18. Study on bandwidth enhancement techniques of microstrip antenna

    Directory of Open Access Journals (Sweden)

    Ragab M. Elsagheer

    2016-12-01

    Full Text Available In this paper we present a Novel Triangular UWB microstrip antenna which offers an ultra-wide bandwidth (UWB greater than 8 GHz. This optimum antenna design provides satisfactory gain all over the UWB. The study includes partially truncating the ground plane (defected ground, inserting slits in the triangular radiating patch, and using different substrate materials in order to obtain band-notched UWB. The simulation experiments have been carried out using the IE3D Zeland software. The final antenna design is fabricated on two substrates; FR4 and Droid 5880 (Teflon. The practical measurements well agree with the simulation results.

  19. An empirical spectral bandwidth model for superior conjunction. [spacecraft communication

    Science.gov (United States)

    Rockwell, R. S.

    1978-01-01

    The downlink signal from spacecraft in superior solar conjunction phases suffers a great reduction in signal-to-noise ratio. Responsible in large part for this effect is the line broadening of the signal spectrum. An analytic empirical expression was developed for spectral bandwidth as a function of heliocentric distance from 1 to 20 solar radii. The study is based on spectral broadening data obtained from the superior conjunctions of Helios 1 (1975), Helios 2 (1976), and Pioneer 6 (1968). The empirical fit is based in part on a function describing the electron content in the solar corona.

  20. Bandwidth allocation for video under quality of service constraints

    CERN Document Server

    Anjum, Bushra

    2014-01-01

    We present queueing-based algorithms to calculate the bandwidth required for a video stream so that the three main Quality of Service constraints, i.e., end-to-end delay, jitter and packet loss, are ensured. Conversational and streaming video-based applications are becoming a major part of the everyday Internet usage. The quality of these applications (QoS), as experienced by the user, depends on three main metrics of the underlying network, namely, end-to-end delay, jitter and packet loss. These metrics are, in turn, directly related to the capacity of the links that the video traffic trave

  1. All-optical microwave signal processing based on optical phase modulation

    Science.gov (United States)

    Zeng, Fei

    This thesis presents a theoretical and experimental study of optical phase modulation and its applications in all-optical microwave signal processing, which include all-optical microwave filtering, all-optical microwave mixing, optical code-division multiple-access (CDMA) coding, and ultrawideband (UWB) signal generation. All-optical microwave signal processing can be considered as the use of opto-electronic devices and systems to process microwave signals in the optical domain, which provides several significant advantages such as low loss, low dispersion, light weight, high time bandwidth products, and immunity to electromagnetic interference. In conventional approaches, the intensity of an optical carrier is modulated by a microwave signal based on direct modulation or external modulation. The intensity-modulated optical signal is then fed to a photonic circuit or system to achieve specific signal processing functionalities. The microwave signal being processed is usually obtained based on direct detection, i.e., an opto-electronic conversion by use of a photodiode. In this thesis, the research efforts are focused on the optical phase modulation and its applications in all-optical microwave signal processing. To avoid using coherent detection which is complicated and costly, simple and effective phase modulation to intensity modulation (PM-IM) conversion schemes are pursued. Based on a theoretical study of optical phase modulation, two approaches to achieving PM-IM conversions are proposed. In the first approach, the use of chromatic dispersion induced by a dispersive device to alter the phase relationships among the sidebands and the optical carrier of a phase-modulated optical signal to realize PM-IM conversion is investigated. In the second approach, instead of using a dispersive device, the PM-IM conversion is realized based on optical frequency discrimination implemented using an optical filter. We show that the proposed PM-IM conversion schemes can be

  2. IMPLEMENTASI MANAJEMEN BANDWIDTH DENGAN DISIPLIN ANTRIAN HIERARCHICAL TOKEN BUCKET (HTB PADA SISTEM OPERASI LINUX

    Directory of Open Access Journals (Sweden)

    Muhammad Nugraha

    2017-01-01

    Full Text Available Important Problem on Internet networking is exhausted resource and bandwidth by some user while other user did not get service properly. To overcome that problem we need to implement traffic control and bandwidth management system in router. In this research author want to implement Hierarchical Token Bucket algorithm as queue discipline (qdisc to get bandwidth management accurately in order the user can get bandwidth properly. The result of this research is form the management bandwidth cheaply and efficiently by using Hierarchical Token Bucket qdisc on Linux operating system were able to manage the user as we want.

  3. Analisis Efektifitas Bandwidth Menggunakan Ipcop (Studi Kasus : Balai Besar Teknologi Energi

    Directory of Open Access Journals (Sweden)

    Viva Arifin

    2016-03-01

    Full Text Available Pada Balai Besar Teknologi Energi (B2TE kerap mengalami masalah koneksi.  Masalah koneksi dapat mengganggu jalannya aktifitas komunikasi. Untuk menanggulangi masalah tersebut, maka perlu adanya pengaturan bandwidth.  Salah satu pengaturan bandwidth yang dapat menurunkan beban bandwidth adalah menggunakan pemakaian dua jalur modem ADSL. Pada IPCop pembatasan bandwidth menggunakan Advanced Proxy yaitu dengan download throttling. Pada B2TE total bandwidth pada jaringan antarmuka GREEN adalah 2 Mbps, kemudian dibatasi setiap host/pengguna untuk mengunduh adalah 512 Kbps. Begitu juga pada jaringan antarmuka BLUE bandwidth yang disediakan adalah 512 Kbps, dan untuk setiap pengguna dibatasi untuk mengunduh adalah 512 Kbps. Traffic shaping digunakan untuk membatasi kecepatan lajur. Maksimal kecepatan dibatasi hanya sampai 1 Mbps, sedangkan untuk mengundah 512 Kbps. Hal ini untuk mencegah para pengguna mengunduh data secara berlebihan yang mengakibatkan pemborosan bandwidth.

  4. A wide-bandwidth and high-sensitivity robust microgyroscope

    International Nuclear Information System (INIS)

    Sahin, Korhan; Sahin, Emre; Akin, Tayfun; Alper, Said Emre

    2009-01-01

    This paper reports a microgyroscope design concept with the help of a 2 degrees of freedom (DoF) sense mode to achieve a wide bandwidth without sacrificing mechanical and electronic sensitivity and to obtain robust operation against variations under ambient conditions. The design concept is demonstrated with a tuning fork microgyroscope fabricated with an in-house silicon-on-glass micromachining process. When the fabricated gyroscope is operated with a relatively wide bandwidth of 1 kHz, measurements show a relatively high raw mechanical sensitivity of 131 µV (° s −1 ) −1 . The variation in the amplified mechanical sensitivity (scale factor) of the gyroscope is measured to be less than 0.38% for large ambient pressure variations such as from 40 to 500 mTorr. The bias instability and angle random walk of the gyroscope are measured to be 131° h −1 and 1.15° h −1/2 , respectively

  5. Bandwidth Optimization in Centralized WLANs for Different Traffic Types

    Directory of Open Access Journals (Sweden)

    Haines RJ

    2007-01-01

    Full Text Available Allocating bandwidth between different forms of coexisting traffic (such as web-browsing, streaming, and telephony within a wireless LAN is a challenging and interesting problem. Centralized coordination functions in wireless LANs offer several advantages over distributed approaches, having the benefit of a system overview at the controller, but obtaining a stable configuration of bandwidth allocation for the system is nontrivial. We present, review, and compare different mechanisms to achieve this end, and a number of different means of obtaining the configurations themselves. We describe an analytical model of the system under consideration and present two mathematical approaches to derive solutions for any system configuration and deployment, along with an adaptive feedback-based solution. We also describe a comprehensive simulation-based model for the problem, and a prototype that allows comparison of these approaches. Our investigations demonstrate that a self-adaptive dynamic approach far outperforms any static scheme, and that using a mathematical model to produce the configurations themselves confers several advantages.

  6. Ionospheric Coherence Bandwidth Measurements in the Lower VHF Frequency Range

    Science.gov (United States)

    Suszcynsky, D. M.; Light, M. E.; Pigue, M. J.

    2015-12-01

    The United States Department of Energy's Radio Frequency Propagation (RFProp) experiment consists of a satellite-based radio receiver suite to study various aspects of trans-ionospheric signal propagation and detection in four frequency bands, 2 - 55 MHz, 125 - 175 MHz, 365 - 415 MHz and 820 - 1100 MHz. In this paper, we present simultaneous ionospheric coherence bandwidth and S4 scintillation index measurements in the 32 - 44 MHz frequency range collected during the ESCINT equatorial scintillation experiment. 40-MHz continuous wave (CW) and 32 - 44 MHz swept frequency signals were transmitted simultaneously to the RFProp receiver suite from the Reagan Test Site at Kwajalein Atoll in the Marshall Islands (8.7° N, 167.7° E) in three separate campaigns during the 2014 and 2015 equinoxes. Results show coherence bandwidths as small as ~ 1 kHz for strong scintillation (S4 > 0.7) and indicate a high degree of ionospheric variability and irregularity on 10-m spatial scales. Spread-Doppler clutter effects arising from preferential ray paths to the satellite due to refraction off of isolated density irregularities are also observed and are dominant at low elevation angles. The results are compared to previous measurements and available scaling laws.

  7. Bandwidth Extension of Telephone Speech Aided by Data Embedding

    Directory of Open Access Journals (Sweden)

    David Malah

    2007-01-01

    Full Text Available A system for bandwidth extension of telephone speech, aided by data embedding, is presented. The proposed system uses the transmitted analog narrowband speech signal as a carrier of the side information needed to carry out the bandwidth extension. The upper band of the wideband speech is reconstructed at the receiving end from two components: a synthetic wideband excitation signal, generated from the narrowband telephone speech and a wideband spectral envelope, parametrically represented and transmitted as embedded data in the telephone speech. We propose a novel data embedding scheme, in which the scalar Costa scheme is combined with an auditory masking model allowing high rate transparent embedding, while maintaining a low bit error rate. The signal is transformed to the frequency domain via the discrete Hartley transform (DHT and is partitioned into subbands. Data is embedded in an adaptively chosen subset of subbands by modifying the DHT coefficients. In our simulations, high quality wideband speech was obtained from speech transmitted over a telephone line (characterized by spectral magnitude distortion, dispersion, and noise, in which side information data is transparently embedded at the rate of 600 information bits/second and with a bit error rate of approximately 3⋅10−4. In a listening test, the reconstructed wideband speech was preferred (at different degrees over conventional telephone speech in 92.5% of the test utterances.

  8. Bandwidth Extension of Telephone Speech Aided by Data Embedding

    Directory of Open Access Journals (Sweden)

    Sagi Ariel

    2007-01-01

    Full Text Available A system for bandwidth extension of telephone speech, aided by data embedding, is presented. The proposed system uses the transmitted analog narrowband speech signal as a carrier of the side information needed to carry out the bandwidth extension. The upper band of the wideband speech is reconstructed at the receiving end from two components: a synthetic wideband excitation signal, generated from the narrowband telephone speech and a wideband spectral envelope, parametrically represented and transmitted as embedded data in the telephone speech. We propose a novel data embedding scheme, in which the scalar Costa scheme is combined with an auditory masking model allowing high rate transparent embedding, while maintaining a low bit error rate. The signal is transformed to the frequency domain via the discrete Hartley transform (DHT and is partitioned into subbands. Data is embedded in an adaptively chosen subset of subbands by modifying the DHT coefficients. In our simulations, high quality wideband speech was obtained from speech transmitted over a telephone line (characterized by spectral magnitude distortion, dispersion, and noise, in which side information data is transparently embedded at the rate of 600 information bits/second and with a bit error rate of approximately . In a listening test, the reconstructed wideband speech was preferred (at different degrees over conventional telephone speech in of the test utterances.

  9. Improving microwave antenna gain and bandwidth with phase compensation metasurface

    Directory of Open Access Journals (Sweden)

    Ke Chen

    2015-06-01

    Full Text Available Metasurface, as a planar version of artificial metamaterial, provide an effective way to manipulate electromagnetic wave propagation. Here, we present a transparent metasurface for compensating the out-of-phase radiation from a microstrip patch antenna to improve its radiation gain and bandwidth. Based on the equivalence principle of Huygens’ surface, we propose metasurface composed of both inductive and capacitive resonant elements which could produce high transmission with variable phase characteristics. Such metasurface mounted on a patch antenna can transform the spherical-like phase profile generated from the patch into an in-phase planar one. A prototype antenna has been fabricated and validated the squeezed radiation pattern with suppressed sidelobes as well as enhanced impedance bandwidth due to strong near-field coupling. As operating at around 5.7 GHz, the proposed antenna may have potential application in wireless communication systems especially for point-to-point data transmission. It is believed that the design methodology could also be scaled to other frequency bands such as millimeter or terahertz wave.

  10. Removal of eye blink artifacts in wireless EEG sensor networks using reduced-bandwidth canonical correlation analysis.

    Science.gov (United States)

    Somers, Ben; Bertrand, Alexander

    2016-12-01

    Chronic, 24/7 EEG monitoring requires the use of highly miniaturized EEG modules, which only measure a few EEG channels over a small area. For improved spatial coverage, a wireless EEG sensor network (WESN) can be deployed, consisting of multiple EEG modules, which interact through short-distance wireless communication. In this paper, we aim to remove eye blink artifacts in each EEG channel of a WESN by optimally exploiting the correlation between EEG signals from different modules, under stringent communication bandwidth constraints. We apply a distributed canonical correlation analysis (CCA-)based algorithm, in which each module only transmits an optimal linear combination of its local EEG channels to the other modules. The method is validated on both synthetic and real EEG data sets, with emulated wireless transmissions. While strongly reducing the amount of data that is shared between nodes, we demonstrate that the algorithm achieves the same eye blink artifact removal performance as the equivalent centralized CCA algorithm, which is at least as good as other state-of-the-art multi-channel algorithms that require a transmission of all channels. Due to their potential for extreme miniaturization, WESNs are viewed as an enabling technology for chronic EEG monitoring. However, multi-channel analysis is hampered in WESNs due to the high energy cost for wireless communication. This paper shows that multi-channel eye blink artifact removal is possible with a significantly reduced wireless communication between EEG modules.

  11. Combined Source-Channel Coding of Images under Power and Bandwidth Constraints

    Directory of Open Access Journals (Sweden)

    Fossorier Marc

    2007-01-01

    Full Text Available This paper proposes a framework for combined source-channel coding for a power and bandwidth constrained noisy channel. The framework is applied to progressive image transmission using constant envelope -ary phase shift key ( -PSK signaling over an additive white Gaussian noise channel. First, the framework is developed for uncoded -PSK signaling (with . Then, it is extended to include coded -PSK modulation using trellis coded modulation (TCM. An adaptive TCM system is also presented. Simulation results show that, depending on the constellation size, coded -PSK signaling performs 3.1 to 5.2 dB better than uncoded -PSK signaling. Finally, the performance of our combined source-channel coding scheme is investigated from the channel capacity point of view. Our framework is further extended to include powerful channel codes like turbo and low-density parity-check (LDPC codes. With these powerful codes, our proposed scheme performs about one dB away from the capacity-achieving SNR value of the QPSK channel.

  12. Crystalline Molybdenum Oxide Thin-Films for Application as Interfacial Layers in Optoelectronic Devices

    DEFF Research Database (Denmark)

    Fernandes Cauduro, André Luis; dos Reis, Roberto; Chen, Gong

    2017-01-01

    The ability to control the interfacial properties in metal-oxide thin films through surface defect engineering is vital to fine-tune their optoelectronic properties and thus their integration in novel optoelectronic devices. This is exemplified in photovoltaic devices based on organic, inorganic...... with structural characterizations, this work addresses a novel method for tuning, and correlating, the optoelectronic properties and microstructure of device-relevant MoOx layers....

  13. Blends of conjugated rigid-rod polymers: Novel supramolecular materials for electronics, optoelectronics and photonics

    Energy Technology Data Exchange (ETDEWEB)

    Jenekhe, S.A. [Univ. of Rochester, NY (United States)

    1996-12-31

    Selected examples of binary blends of conjugated polymers will be presented to illustrate the vast scope of their supramolecular structures and electronic, optical, nonlinear optical, and optoelectronic properties.

  14. Graduate studies on optoelectronics in Argentina: an experience

    Science.gov (United States)

    Fernández, Juan C.; Garea, María. T.; Isaurralde, Silvia; Perez, Liliana I.; Raffo, Carlos A.

    2014-07-01

    The number of graduate programs in Optoelectronics in Argentina is scarce. The current Optics and Photonics Education Directory lists only three programs. One of them was launched in 2001 in the Facultad de Ingeniería (College of Engineering), Universidad de Buenos Aires (UBA). This was the first graduate program in the field, leading to a Master Degree in Optoelectronics. This decision arose from the demand of telecommunications industries and several estate- or private-funded research institutions working with us in the fields of lasers, optics, remote sensing, etc. A great bonus was the steady work, during several decades, of research groups in the College on the development of different type of lasers and optical non destructive tests and their engineering applications. As happened in many engineering graduate programs in Argentina at that time, few non full-time students could finish their studies, which called for 800 hours of traditional lecture-recitation classes, and the Master Thesis. In recent years Argentine Education authorities downsized the Master programs to 700 hours of blended learning and we redesigned the Graduate Optoelectronic Engineering Program to meet the challenge, dividing it in two successive one year programs, the first aimed at a professional training for almost immediate insertion in the labor market (called Especialización en Ingeniería Optoelectrónica), and the second (called Maestría en Ingeniería Optoelectrónica y Fotónica) aimed at a more academic and research target to comply with the UBA standards for Master degrees. The present work is a presentation of the new program design, which has begun in the current year.

  15. Optoelectronic sensor device for monitoring ethanol concentration in winemaking applications

    Science.gov (United States)

    Jiménez-Márquez, F.; Vázquez, J.; Úbeda, J.; Rodríguez-Rey, J.; Sánchez-Rojas, J. L.

    2015-05-01

    The supervision of key variables such as sugar, alcohol, released CO2 and microbiological evolution in fermenting grape must is of great importance in the winemaking industry. However, the fermentation kinetics is assessed by monitoring the evolution of the density as it varies during a fermentation, since density is an indicator of the total amount of sugars, ethanol and glycerol. Even so, supervising the fermentation process is an awkward and non-comprehensive task, especially in wine cellars where production rates are massive, and enologists usually measure the density of the extracted samples from each fermentation tank manually twice a day. This work aims at the design of a fast, low-cost, portable and reliable optoelectronic sensor for measuring ethanol concentration in fermenting grape must samples. Different sets of model solutions, which contain ethanol, fructose, glucose, glycerol dissolved in water and emulate the grape must composition at different stages of the fermentation, were prepared both for calibration and validation. The absorption characteristics of these model solutions were analyzed by a commercial spectrophotometer in the NIR region, in order to identify key wavelengths from which valuable information regarding the sample composition can be extracted. Finally, a customized optoelectronic prototype based on absorbance measurements at two wavelengths belonging to the NIR region was designed, fabricated and successfully tested. The system, whose optoelectronics is reduced after a thorough analysis to only two LED lamps and their corresponding paired photodiodes operating at 1.2 and 1.3 μm respectively, calculates the ethanol content by a multiple linear regression.

  16. Graphene and Two-Dimensional Materials for Optoelectronic Applications

    Directory of Open Access Journals (Sweden)

    Andreas Bablich

    2016-03-01

    Full Text Available This article reviews optoelectronic devices based on graphene and related two-dimensional (2D materials. The review includes basic considerations of process technology, including demonstrations of 2D heterostructure growth, and comments on the scalability and manufacturability of the growth methods. We then assess the potential of graphene-based transparent conducting electrodes. A major part of the review describes photodetectors based on lateral graphene p-n junctions and Schottky diodes. Finally, the progress in vertical devices made from 2D/3D heterojunctions, as well as all-2D heterostructures is discussed.

  17. Wonder of nanotechnology quantum optoelectronic devices and applications

    CERN Document Server

    Razeghi, Manijeh; von Klitzing, Klaus

    2013-01-01

    When you look closely, Nature is nanotechnology at its finest. From a single cell, a factory all by itself, to complex systems, such as the nervous system or the human eye, each is composed of specialized nanostructures that exist to perform a specific function. This same beauty can be mirrored when we interact with the tiny physical world that is the realm of quantum mechanics.The Wonder of Nanotechnology: Quantum Optoelectronic Devices and Applications, edited by Manijeh Razeghi, Leo Esaki, and Klaus von Klitzing focuses on the application of nanotechnology to modern semiconductor optoelectr

  18. All-optoelectronic continuous wave THz imaging for biomedical applications

    International Nuclear Information System (INIS)

    Siebert, Karsten J; Loeffler, Torsten; Quast, Holger; Thomson, Mark; Bauer, Tobias; Leonhardt, Rainer; Czasch, Stephanie; Roskos, Hartmut G

    2002-01-01

    We present an all-optoelectronic THz imaging system for ex vivo biomedical applications based on photomixing of two continuous-wave laser beams using photoconductive antennas. The application of hyperboloidal lenses is discussed. They allow for f-numbers less than 1/2 permitting better focusing and higher spatial resolution compared to off-axis paraboloidal mirrors whose f-numbers for practical reasons must be larger than 1/2. For a specific histological sample, an analysis of image noise is discussed

  19. Optoelectronic imaging of speckle using image processing method

    Science.gov (United States)

    Wang, Jinjiang; Wang, Pengfei

    2018-01-01

    A detailed image processing of laser speckle interferometry is proposed as an example for the course of postgraduate student. Several image processing methods were used together for dealing with optoelectronic imaging system, such as the partial differential equations (PDEs) are used to reduce the effect of noise, the thresholding segmentation also based on heat equation with PDEs, the central line is extracted based on image skeleton, and the branch is removed automatically, the phase level is calculated by spline interpolation method, and the fringe phase can be unwrapped. Finally, the imaging processing method was used to automatically measure the bubble in rubber with negative pressure which could be used in the tire detection.

  20. Acousto-optic collinear filter with optoelectronic feedback

    Science.gov (United States)

    Mantsevich, S. N.; Balakshy, V. I.; Kuznetsov, Yu. I.

    2017-04-01

    A spectral optoelectronic system combining a collinear acousto-optic cell fabricated of calcium molybdate single crystal and a positive electronic feedback is proposed first and examined theoretically and experimentally. The feedback signal is formed at the cell output due to the optical heterodyning effect with the use of an unconventional regime of cell operation. It is shown that the feedback enables controlling spectral characteristics of the acousto-optic cell, resulting in enhancing the spectral resolution and the accuracy of optical wavelength determination. In the experiment, maximal filter passband narrowing was as great as 37 times.

  1. Gamma spectroscopy and optoelectronic imaging with hybrid photon detector

    CERN Document Server

    D'Ambrosio, C; Piedigrossi, D; Rosso, E; Cenceelli, V; De Notaristefani, F; Masini, Gérald; Puertolas, D; Cindolo, F; Mares, J A; Nikl, M; Abreu, M; Rato-Mendes, P; Sousa, P

    2003-01-01

    Hybrid Photon Detectors (HPD) detect light via photocathodes and accelerate the emitted photoelectrons by an electric field towards silicon PIN-anodes, where they are absorbed and generate electronic signals. We have developed two specific types of HPDs: (1) Hybrid photomultiplier tubes for photon counting and gamma spectroscopy; (2) Imaging silicon pixel array tubes for optoelectronic cameras. This paper will illustrate the main achievements, which we obtained in the last years, and will describe and discuss our present main R&D efforts, in particular, in the biomedical imaging field. (27 refs).

  2. MOVPE. Is there any other technology for optoelectronics?

    Energy Technology Data Exchange (ETDEWEB)

    Moon, R.L. [Solid State Materials Department/Solid State Laboratories, Hewlett-Packard Laboratories, Palo Alto (United States)

    1996-12-20

    This paper examines the role that MOVPE (metalorganic vapor phase epitaxy) plays in optoelectronics technology. Its role today accounts for 15% of the grown devices. However, the technology`s contribution over the industry is uneven ranging from as much as 100% in the case of solar cells and photocathodes to only a few percent in today`s LED production. Total usage of MOVPE, and its usage for LEDs, are expected to increase with time to a total contribution to the industry of as much as 25% by the year 2000

  3. Electrical and optoelectronic properties of two-dimensional materials

    Science.gov (United States)

    Wang, Qiaoming

    Electrical and optoelectronic properties of bulk semiconductor materials have been extensively explored in last century. However, when reduced to one-dimensional and two-dimensional, many semiconductors start to show unique electrical and optoelectronic behaviors. In this dissertation, electrical and optoelectronic properties of one-dimensional (nanowires) and two-dimensional semiconductor materials are investigated by various techniques, including scanning photocurrent microscopy, scanning Kelvin probe microscopy, Raman spectroscopy, photoluminescence, and finite-element simulations. In our work, gate-tunable photocurrent in ZnO nanowires has been observed under optical excitation in the visible regime, which originates from the nanowire/substrate interface states. This gate tunability in the visible regime can be used to enhance the photon absorption efficiency, and suppress the undesirable visible-light photodetection in ZnO-based solar cells. The power conversion efficiency of CuInSe2/CdS core-shell nanowire solar cells has been investigated. The highest power conversion efficiency per unit area/volume is achieved with core diameter of 50 nm and the thinnest shell thickness. The existence of the optimal geometrical parameters is due to a combined effect of optical resonances and carrier transport/dynamics. Significant current crowding in two-dimensional black phosphorus field-effect transistors has been found, which has been significantly underestimated by the commonly used transmission-line model. This current crowding can lead to Joule heating close to the contacts. New van der Waals metal-semiconductor junctions have been mechanically constructed and systematically studied. The photocurrent on junction area has been demonstrated to originate from the photothermal effect rather than the photovoltaic effect. Our findings suggest that a reasonable control of interface/surface state properties can enable new and beneficial functionalities in nanostructures. We

  4. Laser processing of thin films for optoelectronic devices

    Science.gov (United States)

    Sugiura, Hideo

    1995-04-01

    This paper reviews the laser processing of II-VI and III-V compound semiconductors for optoelectronic devices. when a laser beam scanning system is combined with MBE or MOCVD apparatus, the resultant growth process is called laser-assisted epitaxy. Laser irradiation of the films has various effects, depending on the growth conditions: doping efficiency, film growth rate, and film composition are affected. Using these effects, laser-assisted epitaxy has been used to make photodetectors, laser diodes, and integrated devices for multiwavelength transmission.

  5. Bandwidth efficient bidirectional 5 Gb/s overlapped-SCM WDM PON with electronic equalization and forward-error correction.

    Science.gov (United States)

    Buset, Jonathan M; El-Sahn, Ziad A; Plant, David V

    2012-06-18

    We demonstrate an improved overlapped-subcarrier multiplexed (O-SCM) WDM PON architecture transmitting over a single feeder using cost sensitive intensity modulation/direct detection transceivers, data re-modulation and simple electronics. Incorporating electronic equalization and Reed-Solomon forward-error correction codes helps to overcome the bandwidth limitation of a remotely seeded reflective semiconductor optical amplifier (RSOA)-based ONU transmitter. The O-SCM architecture yields greater spectral efficiency and higher bit rates than many other SCM techniques while maintaining resilience to upstream impairments. We demonstrate full-duplex 5 Gb/s transmission over 20 km and analyze BER performance as a function of transmitted and received power. The architecture provides flexibility to network operators by relaxing common design constraints and enabling full-duplex operation at BER ∼ 10(-10) over a wide range of OLT launch powers from 3.5 to 8 dBm.

  6. 45-Gbps 3D-CAP transmission over a 16-GHz bandwidth SSMF link assisted by Wiener filtering

    Science.gov (United States)

    Sun, Lin; Du, Jiangbing; You, Yue; Liang, Chenyu; Zhang, Wenjia; Ma, Lin; He, Zuyuan

    2017-04-01

    In this study, the optical 3-dimensional carrier-less amplitude phase (3D-CAP) modulation up to 45 Gbps at 1550 nm is demonstrated and standard single mode fiber (SSMF) transmission up to 10-Km is achieved. The 10-dB bandwidth of the optical back-to-back link is only 16 GHz. Digital Wiener filter is employed to compensate signal distortion with low algorithm complexity. The results indicate a power sensitivity of about 2-dBm after 10-Km transmission for achieving BER of 3.8e-3 at 7% FEC limit. To our best acknowledgement, this is the highest transmission capacity for the 3D-CAP transmission over 10-Km SSMF at 1550 nm. The demonstrated results of 3D-CAP modulation and transmission with paralleled data streams in 3 dimensions present a good potential for improving the density and reducing the cost of parallel optical transceivers in short reach optical interconnections.

  7. Frequency domain approach to the steady state and stability analysis of dual injection-locked optoelectronic oscillators.

    Science.gov (United States)

    Jahanbakht, Sajad

    2017-07-10

    A frequency domain algorithm is proposed for deriving all of the possible steady state modes of dual injection-locked optoelectronic oscillators (DIL-OEOs), corresponding to the detailed system parameters, such as the fiber lengths, small signal open loop gains, radio frequency filters' bandwidths, phase shifting values, and injection parameters. It is shown that some or all of the modes computed by the new approach may be unstable; these are just mathematical solutions of the steady state equations. Therefore, it is necessary to check the stability of these modes. A stability analysis approach is proposed, which is based on simulating the slowly varying time domain dynamic governing the perturbation variables. The steady state and stability analysis approaches enable one to predict the required injection parameters for having a reliable steady state injection-locked mode in the DIL-OEO system. The new method requires a much smaller runtime compared to the corresponding time domain methods. In addition, it avoids many simplifying assumptions of the corresponding frequency domain approaches presented in the literature. The validities of the steady state and stability analysis methods are verified by comparing their results with full time domain integrations and with other predictions regarding the required injection parameters for phase locking, as presented in the literature.

  8. Fiber Bragg grating fabrication for the implementation of sensors in the electronics and optoelectronics laboratory at BUAP

    Science.gov (United States)

    Bracamontes Rodríguez, Y. E.; Beltrán Pérez, G.; Castillo Mixcóatl, J.; Muñoz Aguirre, S.

    2011-09-01

    Fiber Bragg gratings (FBG) are important optical devices since they have been quite successful not only in the field of communications but also in sensor systems and optical fiber lasers. In the sensors area they are generally used as detection elements for different physical parameters such as temperature, strain, flow, etc. In the electronics and optoelectronics laboratory at Benemérita Universidad Autónoma de Puebla (LEyO-BUAP), there are already experimental setups of sensors as well as laser systems, where FBGs are fundamental elements for their adequate performance. However, these FBGs are commercial devices and they present limited characteristics in their transmission profiles, bandwidth and reflectivity. On the other hand, in some occasions, the delivery time from the fabricant to the customer is quite long. Therefore, it is important for LEyO to implement a system to fabricate this kind of devices, which would mean LEyO independence in the technological development. In this work, results of FBGs fabrication based on the phase mask technique are presented. Such mask is optimized for UV and it has a period of 1060 nm. A Nd:YAG pulsed laser with a 5 ns pulse length and an energy of 40 mJ was used as the UV source employing the 4th harmonic generation to obtain a 266 nm wavelength. Ge-doped fiber was used to fabricate the devices.

  9. A Hybrid ACO Approach to the Matrix Bandwidth Minimization Problem

    Science.gov (United States)

    Pintea, Camelia-M.; Crişan, Gloria-Cerasela; Chira, Camelia

    The evolution of the human society raises more and more difficult endeavors. For some of the real-life problems, the computing time-restriction enhances their complexity. The Matrix Bandwidth Minimization Problem (MBMP) seeks for a simultaneous permutation of the rows and the columns of a square matrix in order to keep its nonzero entries close to the main diagonal. The MBMP is a highly investigated {NP}-complete problem, as it has broad applications in industry, logistics, artificial intelligence or information recovery. This paper describes a new attempt to use the Ant Colony Optimization framework in tackling MBMP. The introduced model is based on the hybridization of the Ant Colony System technique with new local search mechanisms. Computational experiments confirm a good performance of the proposed algorithm for the considered set of MBMP instances.

  10. Impedance Bandwidth and Gain Improvement for Microstrip Antenna Using Metamaterials

    Directory of Open Access Journals (Sweden)

    H. Xiong

    2012-12-01

    Full Text Available An improved ultra-wideband (UWB and high gain rectangular antenna is specifically designed in this paper using planar-patterned metamaterial concepts. The antenna has isolated triangle gaps and crossed gaps etched on the metal patch and ground plane, respectively. By changing the pattern on the ground, the impedance matching characteristics of the antenna are much better. The -10 dB impedance bandwidth of the proposed antenna is 3.85–15.62 GHz, which is about 267% broader. The proposed antenna has an average gain of 5.42 dB and the peak is 8.36 dB at 13.5 GHz. Compared with the original one, the gain of the proposed antenna improved about 1.4 dB. Moreover, the size is reduced slightly. Simulated and experimental results obtained for this antenna show that it exhibits good radiation behavior within the UWB frequency range

  11. Adaptive slope compensation for high bandwidth digital current mode controller

    DEFF Research Database (Denmark)

    Taeed, Fazel; Nymand, Morten

    2015-01-01

    An adaptive slope compensation method for digital current mode control of dc-dc converters is proposed in this paper. The compensation slope is used for stabilizing the inner current loop in peak current mode control. In this method, the compensation slope is adapted with the variations...... in converter duty cycle. The adaptive slope compensation provides optimum controller operation in term of bandwidth over wide range of operating points. In this paper operation principle of the controller is discussed. The proposed controller is implemented in an FPGA to control a 100 W buck converter....... The experimental results of measured loop-gain at different operating points are presented to validate the theoretical performance of the controller....

  12. Description of a New 400MHz Bandwidth Chirp Transform Spectrometer

    Science.gov (United States)

    Paganini, Lucas; Hartogh, Paul

    A new chirp transform spectrometer (CTS) with a bandwidth of 400MHz and a spectral resolution of 100 kHz has been developed. The CTS is deviced using a digital chirp generator and a preprocessing unit based on a Complementary Metal Oxide Semiconductor (CMOS) and an Application-Specific Integrated Circuit (ASIC). A build in PC 104 computer handles the process control and the external communication via Ethernet and a Transistor-Transistor Logic (TTL) interface. The CTS has been applied to atmospheric science, i.e., a 25-K noise temperature, 22-GHz water vapor, and a 142-GHz ozone system. Astronomical observations have been performed using the Heinrich Hertz submillimeter telescope. In this paper, we describe the function of the CTS and provide information about its functional performance.

  13. Graphene metascreen for designing compact infrared absorbers with enhanced bandwidth

    KAUST Repository

    Chen, Pai-Yen

    2015-03-31

    We propose a compact, wideband terahertz and infrared absorber, comprising a patterned graphene sheet on a thin metal-backed dielectric slab. This graphene-based nanostructure can achieve a low or negative effective permeability, necessary for realizing the perfect absorption. The dual-reactive property found in both the plasmonic graphene sheet and the grounded highpermittivity slab introduces extra poles into the equivalent circuit model of the system, thereby resulting in a dual-band or broadband magnetic resonance that enhances the absorption bandwidth. More interestingly, the two-dimensional patterned graphene sheet significantly simplifies the design and fabrication processes for achieving resonant magnetic response, and allows the frequency-reconfigurable operation via electrostatic gating.

  14. Ultrawide Bandwidth Receiver Based on a Multivariate Generalized Gaussian Distribution

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2015-04-01

    Multivariate generalized Gaussian density (MGGD) is used to approximate the multiple access interference (MAI) and additive white Gaussian noise in pulse-based ultrawide bandwidth (UWB) system. The MGGD probability density function (pdf) is shown to be a better approximation of a UWB system as compared to multivariate Gaussian, multivariate Laplacian and multivariate Gaussian-Laplacian mixture (GLM). The similarity between the simulated and the approximated pdf is measured with the help of modified Kullback-Leibler distance (KLD). It is also shown that MGGD has the smallest KLD as compared to Gaussian, Laplacian and GLM densities. A receiver based on the principles of minimum bit error rate is designed for the MGGD pdf. As the requirement is stringent, the adaptive implementation of the receiver is also carried out in this paper. Training sequence of the desired user is the only requirement when implementing the detector adaptively. © 2002-2012 IEEE.

  15. Bandwidth Efficient Hybrid Synchronization for Wireless Sensor Network

    DEFF Research Database (Denmark)

    Dnyaneshwar, Mantri; Prasad, Neeli R.; Prasad, Ramjee

    2015-01-01

    Data collection and transmission are the fundamental operations of Wireless Sensor Networks (WSNs). A key challenge in effective data collection and transmission is to schedule and synchronize the activities of the nodes with the global clock. This paper proposes the Bandwidth Efficient Hybrid...... Synchronization Data Aggregation Algorithm (BESDA) using spanning tree mechanism (SPT). It uses static sink and mobile nodes in the network. BESDA considers the synchronization of a local clock of node with global clock of the network. In the initial stage algorithm established the hierarchical structure...... in the network and then perform the pair-wise synchronization. With the mobility of node, the structure frequently changes causing an increase in energy consumption. To mitigate the problem BESDA aggregate data with the notion of a global timescale throughout the network and schedule based time-division multiple...

  16. Fibre Bragg grating based accelerometer with extended bandwidth

    International Nuclear Information System (INIS)

    Basumallick, Nandini; Biswas, Palas; Dasgupta, Kamal; Bandyopadhyay, Somnath; Chakraborty, Rajib; Chakraborty, Sushanta

    2016-01-01

    We have shown experimentally that the operable bandwidth of a fibre Bragg grating (FBG) based accelerometer can be extended significantly, without compromising its sensitivity, using a post-signal processing technique which involves frequency domain weighting. It has been demonstrated that using the above technique acceleration can be correctly interpreted even when the operating frequency encroaches on the region where the frequency response of the sensor is non-uniform. Two different excitation signals, which we often encounter in structural health monitoring applications, e.g. (i) a signal composed of multi-frequency components and (ii) a sinusoidal excitation with a frequency sweep, have been considered in our experiment. The results obtained have been compared with a piezo accelerometer. (paper)

  17. Development of high frequency and wide bandwidth Johnson noise thermometry

    International Nuclear Information System (INIS)

    Crossno, Jesse; Liu, Xiaomeng; Kim, Philip; Ohki, Thomas A.; Fong, Kin Chung

    2015-01-01

    We develop a high frequency, wide bandwidth radiometer operating at room temperature, which augments the traditional technique of Johnson noise thermometry for nanoscale thermal transport studies. Employing low noise amplifiers and an analog multiplier operating at 2 GHz, auto- and cross-correlated Johnson noise measurements are performed in the temperature range of 3 to 300 K, achieving a sensitivity of 5.5 mK (110 ppm) in 1 s of integration time. This setup allows us to measure the thermal conductance of a boron nitride encapsulated monolayer graphene device over a wide temperature range. Our data show a high power law (T ∼ 4) deviation from the Wiedemann-Franz law above T ∼ 100 K

  18. Dynamic head-neck stabilization and modulation with perturbation bandwidth investigated using a multisegment neuromuscular model

    NARCIS (Netherlands)

    Happee, R. (Riender); de Bruijn, E. (Edo); Forbes, P.A. (Patrick A.); F.C.T. van der Helm (Frans C.)

    2017-01-01

    textabstractThe human head-neck system requires continuous stabilization in the presence of gravity and trunk motion. We investigated contributions of the vestibulocollic reflex (VCR), the cervicocollic reflex (CCR), and neck muscle co-contraction to head-in-space and head-on-trunk stabilization,

  19. Dynamic head-neck stabilization and modulation with perturbation bandwidth investigated using a multisegment neuromuscular model

    NARCIS (Netherlands)

    Happee, R.; de Bruijn, E.; Forbes, P.A.; van der Helm, F.C.T.

    2017-01-01

    The human head-neck system requires continuous stabilization in the presence of gravity and trunk motion. We investigated contributions of the vestibulocollic reflex (VCR), the cervicocollic reflex (CCR), and neck muscle co-contraction to head-in-space and head-on-trunk stabilization, and

  20. Modulation Schemes for Wireless Access

    Directory of Open Access Journals (Sweden)

    F. Vejrazka

    2000-12-01

    Full Text Available Four modulation schemes, namely minimum shift keying (MSK, Gaussianminimum shift keying (GMSK, multiamplitude minimum shift keying(MAMSK and π/4 differential quadrature phase shift keying (π/4-QPSKare described and their applicability to wireless access is discussedin the paper. Low complexity receiver structures based on differentialdetection are analysed to estimate the performance of the modulationschemes in the additive Gaussian noise and the Rayleigh and Riceenvelope fast fading channel. The bandwidth efficiency is calculated toevaluate the modulation schemes. The results show that the MAMSK schemegives the greatest bandwidth efficiency, but its performance in theRayleigh channel is rather poor. In contrast, the MSK scheme is lessbandwidth efficient, but it is more resistant to Rayleigh fading. Theperformance of π/4-QPSK signal is considerably improved by appropriateprefiltering.

  1. Optoelectronic polarimeter controlled by a graphical user interface of Matlab

    International Nuclear Information System (INIS)

    Vilardy, J M; Torres, R; Jimenez, C J

    2017-01-01

    We show the design and implementation of an optical polarimeter using electronic control. The polarimeter has a software with a graphical user interface (GUI) that controls the optoelectronic setup and captures the optical intensity measurement, and finally, this software evaluates the Stokes vector of a state of polarization (SOP) by means of the synchronous detection of optical waves. The proposed optoelectronic polarimeter can determine the Stokes vector of a SOP in a rapid and efficient way. Using the polarimeter proposed in this paper, the students will be able to observe (in an optical bench) and understand the different interactions of the SOP when the optical waves pass through to the linear polarizers and retarder waves plates. The polarimeter prototype could be used as a main tool for the students in order to learn the theory and experimental aspects of the SOP for optical waves via the Stokes vector measurement. The proposed polarimeter controlled by a GUI of Matlab is more attractive and suitable to teach and to learn the polarization of optical waves. (paper)

  2. Enhanced fabrication process of zinc oxide nanowires for optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    García Núñez, C., E-mail: carlos.garcia@uam.es [Grupo de Electrónica y Semiconductores, Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Pau, J.L.; Ruíz, E.; García Marín, A.; García, B.J.; Piqueras, J. [Grupo de Electrónica y Semiconductores, Departamento de Física Aplicada, Universidad Autónoma de Madrid, 28049 Madrid (Spain); Shen, G.; Wilbert, D.S.; Kim, S.M.; Kung, P. [Department of Electrical and Computer Engineering, the University of Alabama, Tuscaloosa, AL 35487 (United States)

    2014-03-31

    Zinc oxide (ZnO) nanowires (NWs) based ultraviolet (UV) sensors have been fabricated using different assembly techniques to form functional structures, aiming at the improvement of the performance of NW-based sensors for optoelectronic applications. NWs with diameters and lengths varying between 90–870 nm and 2–20 μm, respectively, were synthesized by controlling the growth conditions in a chemical vapor transport system. Optical properties of NWs were studied by means of transmission spectroscopy. Electrical properties of single ZnO NW-based sensors were analyzed in dark and under UV illumination (at photon wavelength of λ < 370 nm) as a function of the NW diameter. Results of the study indicate that reduction of the NW diameter below 200 nm leads to an improvement of the photocurrent (at λ < 370 nm) up to 10{sup 2} μA and a decrease of the decay time around 150 s. These enhancements may help to improve the performance of ZnO-based optoelectronic devices. - Highlights: • ZnO nanowires (NWs) with diameters 90–870 nm were grown by chemical vapor transport. • ZnO NWs showed strong absorption in the UV range. • Different assembly techniques were tested for preparing ZnO NW-based UV sensors. • Sensor photoresponses were around 10{sup 3} A/W. • Reducing NW diameter below 200 nm improved sensor photosensitivity.

  3. Bioinspired Transparent Laminated Composite Film for Flexible Green Optoelectronics.

    Science.gov (United States)

    Lee, Daewon; Lim, Young-Woo; Im, Hyeon-Gyun; Jeong, Seonju; Ji, Sangyoon; Kim, Yong Ho; Choi, Gwang-Mun; Park, Jang-Ung; Lee, Jung-Yong; Jin, Jungho; Bae, Byeong-Soo

    2017-07-19

    Herein, we report a new version of a bioinspired chitin nanofiber (ChNF) transparent laminated composite film (HCLaminate) made of siloxane hybrid materials (hybrimers) reinforced with ChNFs, which mimics the nanofiber-matrix structure of hierarchical biocomposites. Our HCLaminate is produced via vacuum bag compressing and subsequent UV-curing of the matrix resin-impregnated ChNF transparent paper (ChNF paper). It is worthwhile to note that this new type of ChNF-based transparent substrate film retains the strengths of the original ChNF paper and compensates for ChNF paper's drawbacks as a flexible transparent substrate. As a result, compared with high-performance synthetic plastic films, such as poly(ethylene terephthalate), poly(ether sulfone), poly(ethylene naphthalate), and polyimide, our HCLaminate is characterized to exhibit extremely smooth surface topography, outstanding optical clarity, high elastic modulus, high dimensional stability, etc. To prove our HCLaminate as a substrate film, we use it to fabricate flexible perovskite solar cells and a touch-screen panel. As far as we know, this work is the first to demonstrate flexible optoelectronics, such as flexible perovskite solar cells and a touch-screen panel, actually fabricated on a composite film made of ChNF. Given its desirable macroscopic properties, we envision our HCLaminate being utilized as a transparent substrate film for flexible green optoelectronics.

  4. Study and practice of flipped classroom in optoelectronic technology curriculum

    Science.gov (United States)

    Shi, Jianhua; Lei, Bing; Liu, Wei; Yao, Tianfu; Jiang, Wenjie

    2017-08-01

    "Flipped Classroom" is one of the most popular teaching models, and has been applied in more and more curriculums. It is totally different from the traditional teaching model. In the "Flipped Classroom" model, the students should watch the teaching video afterschool, and in the classroom only the discussion is proceeded to improve the students' comprehension. In this presentation, "Flipped Classroom" was studied and practiced in opto-electronic technology curriculum; its effect was analyzed by comparing it with the traditional teaching model. Based on extensive and deep investigation, the phylogeny, the characters and the important processes of "Flipped Classroom" are studied. The differences between the "Flipped Classroom" and the traditional teaching model are demonstrated. Then "Flipped Classroom" was practiced in opto-electronic technology curriculum. In order to obtain high effectiveness, a lot of teaching resources were prepared, such as the high-quality teaching video, the animations and the virtual experiments, the questions that the students should finish before and discussed in the class, etc. At last, the teaching effect was evaluated through analyzing the result of the examination and the students' surveys.

  5. Coherent and ultrafast optoelectronics in III-V semiconductor compounds

    Energy Technology Data Exchange (ETDEWEB)

    Foerst, M.; Nagel, M.; Awad, M.; Waechter, M.; Kurz, H. [Institut fuer Halbleitertechnik, RWTH Aachen University, 52074 Aachen (Germany); Dekorsy, T. [Universitaet Konstanz, Fachbereich Physik, 78457 Konstanz (Germany)

    2007-08-15

    III-V compound semiconductors offer a fascinating multitude of phenomena which have become accessible via ultrafast time-resolved spectroscopy. Coherent vibronic and electronic dynamics are prepared by excitation with taylored femtosecond laser pulses. The analysis of their temporal dephasing or decay provides deep insights into the interaction between electronic and vibronic degrees of freedom and the surrounding bath in high purity quantum structures. In contrast to coherent electronic or vibronic states, deliberately introduced growth defects can be used to drastically shorten the lifetime of optically excited carriers. Sub-picosecond carrier lifetimes open the possibility to realize ultrafast saturable absorbers and optoelectronic transducer elements. They are particularly important as key elements in THz technology, such as efficient THz emitters, detectors, and for on-chip THz technology. This paper summarizes the most distinguished results relevant in the context of ultrafast optoelectronics and THz technology obtained in close collaboration with the Paul-Drude-Institute Berlin over the past decade. (copyright 2007 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  6. Development of an optoelectronic holographic platform for otolaryngology applications

    Science.gov (United States)

    Harrington, Ellery; Dobrev, Ivo; Bapat, Nikhil; Flores, Jorge Mauricio; Furlong, Cosme; Rosowski, John; Cheng, Jeffery Tao; Scarpino, Chris; Ravicz, Michael

    2010-08-01

    In this paper, we present advances on our development of an optoelectronic holographic computing platform with the ability to quantitatively measure full-field-of-view nanometer-scale movements of the tympanic membrane (TM). These measurements can facilitate otologists' ability to study and diagnose hearing disorders in humans. The holographic platform consists of a laser delivery system and an otoscope. The control software, called LaserView, is written in Visual C++ and handles communication and synchronization between hardware components. It provides a user-friendly interface to allow viewing of holographic images with several tools to automate holography-related tasks and facilitate hardware communication. The software uses a series of concurrent threads to acquire images, control the hardware, and display quantitative holographic data at video rates and in two modes of operation: optoelectronic holography and lensless digital holography. The holographic platform has been used to perform experiments on several live and post-mortem specimens, and is to be deployed in a medical research environment with future developments leading to its eventual clinical use.

  7. Research and development of photovoltaic power system. Study of carrier dynamics in a-Si from optical and optoelectronic properties; Taiyoko hatsuden system no kenky kaihatsu. Amorphous silicon no koden tokusei to sono carrier dynamics no kogakuteki kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Hamakawa, K. [Osaka University, Osaka (Japan). Faculty of Engineering Science

    1994-12-01

    This paper reports the result obtained during fiscal 1994 on research on an optical study of optoelectronic properties of amorphous silicon and its carrier dynamics. Studies have been performed on elucidation of the optoelectronic conversion mechanism in an a-Si film p-i-n junction system and the relationship of the mechanism with the optoelectronic properties. In the studies, optically induced defect level distribution was evaluated by using the modulated optical current spectroscopy, and confirmation was made on model forecast and qualitative agreement, such as large increase in neutral defect levels in association with beam irradiation. In research on elucidation of a film forming mechanism for a-Si based alloys, and material property control, a high-sensitivity reflective infrared spectroscopy was used to observe mechanisms such as treatments and processes given in device fabrication. In research on optical and optoelectronic properties of an s-Si alloy thin film by using the modulated spectroscopy, a new evaluation technology dealing with amorphous semiconductors was developed. The technology separately evaluates carrier migration factors of electrons and holes by combining polarization angle dependence of electro-absorption signals with hole migration measurements. 4 figs.

  8. High-Bandwidth Photon-Counting Detectors with Enhanced Near-Infrared Response Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Long-range optical telecommunications (LROT) impose challenging requirements on detector array sensitivity at 1064nm and arrays timing bandwidth. Large photonic...

  9. Minimum cost maximum flow algorithm for upstream bandwidth allocation in OFDMA passive optical networks

    Science.gov (United States)

    Wu, Yating; Kuang, Bin; Wang, Tao; Zhang, Qianwu; Wang, Min

    2015-12-01

    This paper presents a minimum cost maximum flow (MCMF) based upstream bandwidth allocation algorithm, which supports differentiated QoS for orthogonal frequency division multiple access passive optical networks (OFDMA-PONs). We define a utility function as the metric to characterize the satisfaction degree of an ONU on the obtained bandwidth. The bandwidth allocation problem is then formulated as maximizing the sum of the weighted total utility functions of all ONUs. By constructing a flow network graph, we obtain the optimized bandwidth allocation using the MCMF algorithm. Simulation results show that the proposed scheme improves the performance in terms of mean packet delay, packet loss ratio and throughput.

  10. Bandwidth allocation strategy for traffic systems of scale-free network

    International Nuclear Information System (INIS)

    Ling Xiang; Hu MaobBin; Du Wenbo; Jiang Rui; Wu Yonghong; Wu Qingsong

    2010-01-01

    In this Letter, the bandwidth resource allocation strategy is considered for traffic systems of complex networks. With a finite resource of bandwidth, an allocation strategy with preference parameter α is proposed considering the links importance. The performance of bandwidth allocation strategy is studied for the local routing protocol and the shortest path protocol. When important links are slightly favored in the bandwidth allocation, the system can achieve the optimal traffic performance for the two routing protocols. For the shortest path protocol, we also give a method to estimate the network traffic capacity theoretically.

  11. Bandwidth-adaptable silicon photonic differentiator employing a slow light effect

    DEFF Research Database (Denmark)

    Yan, Siqi; Cheng, Ziwei; Frandsen, Lars Hagedorn

    2017-01-01

    A photonic differentiator (DIFF) plays a crucial role in photonic circuits. Despite the fact that a DIFF having a tera-hertz bandwidth has been reported, the practical bandwidth is limited to being a bandpass response. In this Letter, we propose the concept of a bandwidth-adaptable DIFF, which...... exploits the slow light effect in a photonic crystal waveguide (PhCW) to overcome the inherent bandwidth limitation of current photonic DIFFs. We fabricated a PhCW Mach-Zehnder interferometer (PhCW-MZI) on the silicon-onisolator material platform to validate our concept. Input Gaussian pulses with full...

  12. The Prediction of Bandwidth On Need Computer Network Through Artificial Neural Network Method of Backpropagation

    Directory of Open Access Journals (Sweden)

    Ikhthison Mekongga

    2014-02-01

    Full Text Available The need for bandwidth has been increasing recently. This is because the development of internet infrastructure is also increasing so that we need an economic and efficient provider system. This can be achieved through good planning and a proper system. The prediction of the bandwidth consumption is one of the factors that support the planning for an efficient internet service provider system. Bandwidth consumption is predicted using ANN. ANN is an information processing system which has similar characteristics as the biologic al neural network.  ANN  is  chosen  to  predict  the  consumption  of  the  bandwidth  because  ANN  has  good  approachability  to  non-linearity.  The variable used in ANN is the historical load data. A bandwidth consumption information system was built using neural networks  with a backpropagation algorithm to make the use of bandwidth more efficient in the future both in the rental rate of the bandwidth and in the usage of the bandwidth.Keywords: Forecasting, Bandwidth, Backpropagation

  13. Proceedings of the international conference on optoelectronic science and engineering '90

    International Nuclear Information System (INIS)

    Da-Heng, W.

    1990-01-01

    This book covers the International Conference on Optoelectric Science and Engineering '90. Topics addressed included: optoelectronic intelligent sensors, optoelectronic tests, analysis, measurement and control, laser devices and their applications, infrared optics, low level light technology, fiber optics, photovoltaics and solar energy systems, image processing, optical disk information storage, and pattern recognition and robot vision

  14. Scaling Mesa Indium Phosphide DHBTs to Record Bandwidths

    Science.gov (United States)

    Lobisser, Evan

    Indium phosphide heterojunction bipolar transistors are able to achieve higher bandwidths at a given feature size than transistors in the Silicon material system for a given feature size. Indium phosphide bipolar transistors demonstrate higher breakdown voltages at a given bandwidth than both Si bipolars and field effect transistors in the InP material system. The high bandwidth of InP HBTs results from both intrinsic material parameters and bandgap engineering through epitaxial growth. The electron mobility in the InGaAs base and saturation velocity in the InP collector are both approximately three times higher than their counterparts in the SiGe material system. Resistance of the base can be made very low due to the large offset in the valence band between the InP emitter and the InGaAs base, which allows the base to be doped on the order of 1020 cm-3 with negligible reduction in emitter injection efficiency. This thesis deals with type-I, NPN dual-heterojunction bipolar transistors. The emitters are InP, and the base is InGaAs. There is a thin (˜ 10 nm) n-type InGaAs "setback" region, followed by a chirped superlattice InGaAs/InAlAs grade to the InP collector. The setback, grade, and collector are all lightly doped n-type. The emitter and collector are contacted through thin (˜ 5 nm) heavily doped n-type InGaAs layers to reduce contact resistivity. The primary focus of this work is increasing the bandwidth of InP HBTs through the proportional scaling of the device dimensions, both layer thicknesses and junction areas, as well as the reduction of the contact resistivities associated with the transistor. Essentially, all RC time constants and transit times must be reduced by a factor of two to double a transistor's bandwidth. Chapter 2 describes in detail the scaling laws and design principles for high frequency bipolar transistor design. A low-stress, blanket sputter deposited composite emitter metal process was developed. Refractory metal base contacts were

  15. An optoelectronic framework enabled by low-dimensional phase-change films

    Science.gov (United States)

    Hosseini, Peiman; Wright, C. David; Bhaskaran, Harish

    2014-07-01

    The development of materials whose refractive index can be optically transformed as desired, such as chalcogenide-based phase-change materials, has revolutionized the media and data storage industries by providing inexpensive, high-speed, portable and reliable platforms able to store vast quantities of data. Phase-change materials switch between two solid states--amorphous and crystalline--in response to a stimulus, such as heat, with an associated change in the physical properties of the material, including optical absorption, electrical conductance and Young's modulus. The initial applications of these materials (particularly the germanium antimony tellurium alloy Ge2Sb2Te5) exploited the reversible change in their optical properties in rewritable optical data storage technologies. More recently, the change in their electrical conductivity has also been extensively studied in the development of non-volatile phase-change memories. Here we show that by combining the optical and electronic property modulation of such materials, display and data visualization applications that go beyond data storage can be created. Using extremely thin phase-change materials and transparent conductors, we demonstrate electrically induced stable colour changes in both reflective and semi-transparent modes. Further, we show how a pixelated approach can be used in displays on both rigid and flexible films. This optoelectronic framework using low-dimensional phase-change materials has many likely applications, such as ultrafast, entirely solid-state displays with nanometre-scale pixels, semi-transparent `smart' glasses, `smart' contact lenses and artificial retina devices.

  16. Integration of 2D materials on a silicon photonics platform for optoelectronics applications

    Directory of Open Access Journals (Sweden)

    Youngblood Nathan

    2016-12-01

    Full Text Available Owing to enormous growth in both data storage and the demand for high-performance computing, there has been a major effort to integrate telecom networks on-chip. Silicon photonics is an ideal candidate, thanks to the maturity and economics of current CMOS processes in addition to the desirable optical properties of silicon in the near IR. The basics of optical communication require the ability to generate, modulate, and detect light, which is not currently possible with silicon alone. Growing germanium or III/V materials on silicon is technically challenging due to the mismatch between lattice constants and thermal properties. One proposed solution is to use two-dimensional materials, which have covalent bonds in-plane, but are held together by van der Waals forces out of plane. These materials have many unique electrical and optical properties and can be transferred to an arbitrary substrate without lattice matching requirements. This article reviews recent progress toward the integration of 2D materials on a silicon photonics platform for optoelectronic applications.

  17. An optoelectronic framework enabled by low-dimensional phase-change films.

    Science.gov (United States)

    Hosseini, Peiman; Wright, C David; Bhaskaran, Harish

    2014-07-10

    The development of materials whose refractive index can be optically transformed as desired, such as chalcogenide-based phase-change materials, has revolutionized the media and data storage industries by providing inexpensive, high-speed, portable and reliable platforms able to store vast quantities of data. Phase-change materials switch between two solid states--amorphous and crystalline--in response to a stimulus, such as heat, with an associated change in the physical properties of the material, including optical absorption, electrical conductance and Young's modulus. The initial applications of these materials (particularly the germanium antimony tellurium alloy Ge2Sb2Te5) exploited the reversible change in their optical properties in rewritable optical data storage technologies. More recently, the change in their electrical conductivity has also been extensively studied in the development of non-volatile phase-change memories. Here we show that by combining the optical and electronic property modulation of such materials, display and data visualization applications that go beyond data storage can be created. Using extremely thin phase-change materials and transparent conductors, we demonstrate electrically induced stable colour changes in both reflective and semi-transparent modes. Further, we show how a pixelated approach can be used in displays on both rigid and flexible films. This optoelectronic framework using low-dimensional phase-change materials has many likely applications, such as ultrafast, entirely solid-state displays with nanometre-scale pixels, semi-transparent 'smart' glasses, 'smart' contact lenses and artificial retina devices.

  18. Multiplication theory for dynamically biased avalanche photodiodes: new limits for gain bandwidth product.

    Science.gov (United States)

    Hayat, Majeed M; Ramirez, David A

    2012-03-26

    Novel theory is developed for the avalanche multiplication process in avalanche photodiodes (APDs) under time-varying reverse-biasing conditions. Integral equations are derived characterizing the statistics of the multiplication factor and the impulse-response function of APDs, as well as their breakdown probability, all under the assumption that the electric field driving the avalanche process is time varying and spatially nonuniform. Numerical calculations generated by the model predict that by using a bit-synchronous sinusoidal biasing scheme to operate the APD in an optical receiver, the pulse-integrated gain-bandwidth product can be improved by a factor of 5 compared to the same APD operating under the conventional static biasing. The bit-synchronized periodic modulation of the electric field in the multiplication region serves to (1) produce large avalanche multiplication factors with suppressed avalanche durations for photons arriving in the early phase of each optical pulse; and (2) generate low avalanche gains and very short avalanche durations for photons arriving in the latter part of each optical pulse. These two factors can work together to reduce intersymbol interference in optical receivers without sacrificing sensitivity.

  19. Frequency division multiple transmission method to utilize the wide bandwidth property of capacitive micromachined ultrasonic transducer arrays

    Science.gov (United States)

    Lee, Seunghun; Kim, Bae-Hyung; Jeon, Taeho; Kim, Youngil; Cho, Kyungil; Song, Jongkeun

    2013-03-01

    CMUT-on-ASIC integration techniques are promising for the development of lower cost smaller volume scanners with higher performance in terms of features and image qualities because it minimizes parasitic capacitances and ultimately improves signal-to-noise ratio (SNR). Moreover, a frequency bandwidth of CMUT array is known as relatively broader than that of other ultrasonic transducer arrays. To utilize the wide bandwidth characteristic of the CMUT arrays, in this paper, we introduce a FDMA (frequency division multiple access) based ultrasound imaging technique using orthogonally band-divided coded signals to provide dynamic transmit focused imaging without sacrificing the frame rate. In the presented method, the orthogonal sub-band coded signals are simultaneously fired on multiple ranges, in which each signal is focused at a different range, in one transmission event. This paper also presents an ultrasound imageformation method and a modulation and demodulation process of orthogonal sub-band coded signals designed within the frequency bandwidth of the CMUT arrays. The presented method is verified by computer simulations using Field II and experiments. The simulation results using a computer generated tissue mimicking phantom show that the presented method can be achieved with both increased image quality and frame rate. The experimental results to verify the feasibility of the presented method using orthogonal sub-band coded signals show that the reflected signals from targets are successfully separated into two compressed signals. Currently, we are extending the presented approach to ultrasound imaging technique for volumetric ultrasound scanners using 2-D CMUT-on-ASIC arrays.

  20. German-Chinese cooperative Bachelor in engineering physics/optoelectronics

    Science.gov (United States)

    Wick, Michael; Lindner, Gerhard; Zimmer, Katja; Zheng, Jihong; Xu, Boqing; Wang, Ning; Schreiner, Rupert; Fuhrmann, Thomas; Seebauer, Gudrun

    2017-08-01

    The University of Shanghai for Science and Technology (USST), the Coburg University of Applied Sciences and Arts (CUASA) and the OTH Regensburg, University of Applied Sciences (OTHR) established an English taught international cooperative bachelor program in the area of Engineering Physics/Optoelectronics. Students from China study their first four semesters at USST. They continue their studies in Germany for the last three semesters, including an internship and a bachelor thesis, graduating with a Chinese and a German bachelor degree. Students from Germany study their third and fourth semester at USST to gain international experience. While the first cohort of Chinese students is currently in Germany, the second cohort of German students is in Shanghai. Up to now the feedback regarding this study program is completely positive, thus it is planned to develop it further.

  1. Optoelectronic investigation of nanodiamond interactions with human blood

    Science.gov (United States)

    Ficek, M.; Wróbel, M. S.; Wasowicz, M.; Jedrzejewska-Szczerska, M.

    2016-03-01

    We present optoelectronic investigation of in vitro interactions of whole human blood with different nanodiamond biomarkers. Plasmo-chemical modifications of detonation nanodiamond particles gives the possibility for controlling their surface for biological applications. Optical investigations reveal the biological activity of nanodiamonds in blood dependent on its surface termination. We compare different types of nanodiamonds: commercial non-modified detonation nanodiamonds, and nanodiamonds modified by MW PACVD method with H2-termination, and chemically modified nanodiamond with O2-termination. The absorption spectra, and optical microscope investigations were conducted. The results indicate haemocompatibility of non-modified detonation nanodiamond as well as modified nanodiamonds, which enables their application for drug delivery, as well as sensing applications.

  2. Transparent electrode of nanoscale metal film for optoelectronic devices

    Science.gov (United States)

    Lee, Illhwan; Lee, Jong-Lam

    2015-01-01

    This paper reviews the principles, impediments, and recent progress in the development of ultrathin flexible Ag electrodes for use in flexible optoelectronic devices. Thin Ag-based electrodes are promising candidates for next-generation flexible transparent electrodes. Thin Ag-based electrodes that have a microcavity structure show the best device performance, but have relatively low optical transmittance (OT) due to reflection and absorption of photons by the thin Ag; this trait causes problems such as spectral narrowing and change of emission color with viewing angle in white organic light-emitting diodes. Thinning the Ag electrode to overcome these problems. This ultrathin Ag electrode has a high OT, while providing comparable sheet resistance similar to indium tin oxide. As the OT of the electrode increases, the cavity is weakened, so the spectral width of the emission and the angular color stability are increased.

  3. Properties and potential optoelectronic applications of lead halide perovskite nanocrystals

    Science.gov (United States)

    Kovalenko, Maksym V.; Protesescu, Loredana; Bodnarchuk, Maryna I.

    2017-11-01

    Semiconducting lead halide perovskites (LHPs) have not only become prominent thin-film absorber materials in photovoltaics but have also proven to be disruptive in the field of colloidal semiconductor nanocrystals (NCs). The most important feature of LHP NCs is their so-called defect-tolerance—the apparently benign nature of structural defects, highly abundant in these compounds, with respect to optical and electronic properties. Here, we review the important differences that exist in the chemistry and physics of LHP NCs as compared with more conventional, tetrahedrally bonded, elemental, and binary semiconductor NCs (such as silicon, germanium, cadmium selenide, gallium arsenide, and indium phosphide). We survey the prospects of LHP NCs for optoelectronic applications such as in television displays, light-emitting devices, and solar cells, emphasizing the practical hurdles that remain to be overcome.

  4. Molecular beam epitaxy for high-efficiency nitride optoelectronics

    Energy Technology Data Exchange (ETDEWEB)

    Heffernan, J.; Kauer, M.; Windle, J.; Hooper, S.E.; Bousquet, V.; Zellweger, C.; Barnes, J.M. [Sharp Laboratories of Europe, Edmund Halley Road, Oxford Science Park, Oxford OX4 4GB (United Kingdom)

    2006-06-15

    We review the significant progress made in the development of nitride laser diodes by molecular beam epitaxy (MBE). We report on our recent result of room temperature continuous-wave operation of InGaN quantum well laser diodes grown by MBE. Ridge waveguide lasers fabricated on freestanding GaN substrates have a continuous-wave threshold current of 125 mA, corresponding to a threshold current density of 5.7 kA cm{sup -2}. The lasers have a threshold voltage of 8.6 V and a lifetime of several minutes. We outline the further technical challenges associated with demonstrating lifetimes of several thousand hours and present an assessment of the potential of MBE as a growth method for commercial quality nitride optoelectronic devices. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  5. Advanced Opto-Electronics (LIDAR and Microsensor Development)

    Science.gov (United States)

    Vanderbilt, Vern C. (Technical Monitor); Spangler, Lee H.

    2005-01-01

    Our overall intent in this aspect of the project were to establish a collaborative effort between several departments at Montana State University for developing advanced optoelectronic technology for advancing the state-of-the-art in optical remote sensing of the environment. Our particular focus was on development of small systems that can eventually be used in a wide variety of applications that might include ground-, air-, and space deployments, possibly in sensor networks. Specific objectives were to: 1) Build a field-deployable direct-detection lidar system for use in measurements of clouds, aerosols, fish, and vegetation; 2) Develop a breadboard prototype water vapor differential absorption lidar (DIAL) system based on highly stable, tunable diode laser technology developed previously at MSU. We accomplished both primary objectives of this project, in developing a field-deployable direct-detection lidar and a breadboard prototype of a water vapor DIAL system. Paper summarizes each of these accomplishments.

  6. Microbeam High Angular Resolution Diffraction Applied to Optoelectronic Devices

    International Nuclear Information System (INIS)

    Kazimirov, A.; Bilderback, D. H.; Sirenko, A. A.; Cai, Z.-H.; Lai, B.

    2007-01-01

    Collimating perfect crystal optics in a combination with the X-ray focusing optics has been applied to perform high angular resolution microbeam diffraction and scattering experiments on micron-size optoelectronic devices produced by modern semiconductor technology. At CHESS, we used capillary optics and perfect Si/Ge crystal(s) arrangement to perform X-ray standing waves, high angular-resolution diffraction and high resolution reciprocal space mapping analysis. At the APS, 2ID-D microscope beamline, we employed a phase zone plate producing a beam with the size of 240 nm in the horizontal plane and 350 nm in the vertical (diffraction) plane and a perfect Si (004) analyzer crystal to perform diffraction analysis of selectively grown InGaAsP and InGaAlAs-based waveguides with arc sec angular resolution

  7. Gallium Nitride Based Semiconductors for Short Wavelength Optoelectronics

    Science.gov (United States)

    Denbaars, S. P.

    In this article we review the key technologies for GaN based materials and devices. Developments in the methods for thin film deposition by metalorganic chemical vapor deposition (MOCVD) and molecular beam epitaxy (MBE) and resulting film properties are highlighted. Breakthroughs in materials growth has enabled extremely high efficiency blue and green GaN LEDs to be achieved for the first time. GaN LEDs complete the primary color spectrum and have enabled bright and reliable full-color solid state displays to be realized. Recently, room temperature operation of pulsed current injection blue-violet lasers emitting at 417 nm has further increased possible applications for GaN based optoelectronic devices.

  8. High Bandwidth Short Stroke Rotary Fast Tool Servo

    Energy Technology Data Exchange (ETDEWEB)

    Montesanti, R C; Trumper, D L

    2003-08-22

    This paper presents the design and performance of a new rotary fast tool servo (FTS) capable of developing the 40 g's tool tip acceleration required to follow a 5 micron PV sinusoidal surface at 2 kHz with a planned accuracy of 50 nm, and having a full stroke of 50 micron PV at lower frequencies. Tests with de-rated power supplies have demonstrated a closed-loop unity-gain bandwidth of 2 kHz with 20 g's tool acceleration, and we expect to achieve 40 g's with supplies providing {+-} 16 Amp to the Lorentz force actuator. The use of a fast tool servo with a diamond turning machine for producing non-axisymmetric or textured surfaces on a workpiece is well known. Our new rotary FTS was designed to specifically accommodate fabricating prescription textured surfaces on 5 mm diameter spherical target components for High Energy Density Physics experiments on the National Ignition Facility Laser (NIF).

  9. Social value of high bandwidth networks: creative performance and education.

    Science.gov (United States)

    Mansell, Robin; Foresta, Don

    2016-03-06

    This paper considers limitations of existing network technologies for distributed theatrical performance in the creative arts and for symmetrical real-time interaction in online learning environments. It examines the experience of a multidisciplinary research consortium that aimed to introduce a solution to latency and other network problems experienced by users in these sectors. The solution builds on the Multicast protocol, Access Grid, an environment supported by very high bandwidth networks. The solution is intended to offer high-quality image and sound, interaction with other network platforms, maximum user control of multipoint transmissions, and open programming tools that are flexible and modifiable for specific uses. A case study is presented drawing upon an extended period of participant observation by the authors. This provides a basis for an examination of the challenges of promoting technological innovation in a multidisciplinary project. We highlight the kinds of technical advances and cultural and organizational changes that would be required to meet demanding quality standards, the way a research consortium planned to engage in experimentation and learning, and factors making it difficult to achieve an open platform that is responsive to the needs of users in the creative arts and education sectors. © 2016 The Author(s).

  10. Review of single transient oscillographic recorders with gigahertz bandwidth

    International Nuclear Information System (INIS)

    Campbell, D.E.

    1982-01-01

    In laser driven inertial confinement fusion research, at Livermore, we are diagnosing many phenomena that occur in a time frame that exceeds the capabilities of even the most advanced, present day oscillographic recording instruments. Many of the by-products of the interaction between the laser beam and fuel pellet are monitored to determine the specifics of the fusion process. By the use of appropriate detectors, we convert the information contained in the radiated by-products to electrical signals which are recorded on high bandwidth oscillographic recorders. Our present range of recording capabilities for one x-ray diagnostic measurement in use at Livermore is shown. A commonly used configuration consists of an XRD-31 x-ray detector connected to a direct access Tektronix R7912 transient digitizer using 1/2 in. diameter air dielectric coaxial cable. This configuration gives a system fwhm of approximately 335 ps. Our premier configuration, on the other hand, consists of an improved response detector and a French Thomson-CSF TSN-660 oscilloscope with a shorter length of coaxial cable (typically 20 feet). The system fwhm in this case is less than 120 ps which is our fastest oscillographic recording system at the present time

  11. A Multicarrier Multiplexing Method for Very Wide Bandwidth Transmission

    Directory of Open Access Journals (Sweden)

    Efthymoglou George

    2006-01-01

    Full Text Available The multicarrier orthogonal code division multiplexing (MC-OCDM introduced here has been designed for very wide bandwidth (VWB point-to-point and point-to-multipoint transmission. In order to meet VWB transmission requirements, the MC-OCDM design has two components, the basic and the composite. The basic MC-OCDM is a generalized form of the standard orthogonal frequency division multiplexing (OFDM. It has the property of distributing the power of each transmitted symbol into all subcarrier frequencies. Each subcarrier will then carry all transmitted symbols which are distinguished by orthogonal Hadamard sequences. The resulting system is shown to improve the performance of OFDM by introducing frequency and time diversity. As shown, by both analysis and simulation, the basic MC-OCDM combats the effects of narrowband interference (NBI. In particular, the simulation results show that the BER performance of the basic MC-OCDM in the presence of NBI is better than OFDM for both coded and uncoded systems. Furthermore, the composite MC-OCDM is a method of orthogonal frequency division multiplexing (OFDM basic MC-OCDM channels. This allows us to multiplex more than one basic MC-OCDM channel into a VWB transmission system which can have the performance and spectral efficiency required in fixed wireless transmission environments.

  12. Bandwidth-Enhanced Low-Profile Antenna with Parasitic Patches

    Directory of Open Access Journals (Sweden)

    Son Xuat Ta

    2017-01-01

    Full Text Available This paper presents low-profile broadband antennas, which are composed of four parasitic patches placed between planar radiators and a perfect electric conductor ground plane. Two types of planar radiators, a conventional dipole and a crossed dipole, are employed to produce linearly polarized (LP and circularly polarized (CP radiations, respectively. The radiator and parasitic patches are realized on thin substrates to lower the cost. Owing to the presence of parasitic patches, the antenna performance improves in terms of profile reduction, resonant frequency decrease, and bandwidth enhancement. These improvements are discussed and confirmed computationally and experimentally. The LP design with the overall dimensions of 120 mm × 120 mm × 16.3 mm (0.64λ0 × 0.64λ0 × 0.087λ0 at 1.6 GHz has a |S11|  96%. The CP design, which has the same physical size as the LP case, has a |S11|  90%.

  13. QoS routing via multiple paths using bandwidth reservation

    Energy Technology Data Exchange (ETDEWEB)

    Rao, N.S.V.; Batsell, S.G.

    1997-11-01

    The authors address the problem of computing a multipath, consisting of possibly overlapping paths, to transmit data from the source node s to the destination node d over a computer network while ensuring deterministic bounds on end-to-end delay or delivery rate. They consider two generic routing problems within the framework wherein bandwidth can be reserved, and guaranteed, once reserved, on various links of the communication network. The first problem requires that a message of finite length be transmitted from s to d within {tau} units of time. The second problem requires that a sequential message of r units be transmitted at a rate of {eta} such that maximum time difference between two units that are received out of order is no more than q. They propose a polynomial-time algorithm to the first problem based on an adaptation of the classical Ford-Fulkerson`s method. They present simulation results to illustrate the applicability of the proposed algorithm. They show the second problem to be NP-complete and propose a polynomial-time approximate solution.

  14. QoS routing via multiple paths using bandwidth reservation

    Energy Technology Data Exchange (ETDEWEB)

    Rao, N.S.V.; Batsell, S.G.

    1998-01-01

    The authors address the problem of computing a multipath, consisting of possibly overlapping paths, to transmit data from the source node s to the destination node d over a computer network while ensuring deterministic bounds on end-to-end delay or delivery rate.They consider two generic routing problems within the framework wherein bandwidth can be reserved, and guaranteed, once reserved, on various links of the communication network. The first problem requires that a message of finite length be transmitted from s to d within {tau} units of time. The second problem requires that a sequential message of r units be transmitted at a rate of {eta} such that maximum time difference between two units that are received out of order is no more than q. They propose a polynomial-time algorithm to the first problem based on an adaptation of the classical Ford-Fulkerson`s method. They present simulation results to illustrate the applicability of the proposed algorithm. They show the second problem to be NP-complete, and propose a polynomial-time approximately solution.

  15. Constant-bandwidth constant-temperature hot-wire anemometer.

    Science.gov (United States)

    Ligeza, P

    2007-07-01

    A constant-temperature anemometer (CTA) enables the measurement of fast-changing velocity fluctuations. In the classical solution of CTA, the transmission band is a function of flow velocity. This is a minor drawback when the mean flow velocity does not significantly change, though it might lead to dynamic errors when flow velocity varies over a considerable range. A modification is outlined, whereby an adaptive controller is incorporated in the CTA system such that the anemometer's transmission band remains constant in the function of flow velocity. For that purpose, a second feedback loop is provided, and the output signal from the anemometer will regulate the controller's parameters such that the transmission bandwidth remains constant. The mathematical model of a CTA that has been developed and model testing data allow a through evaluation of the proposed solution. A modified anemometer can be used in measurements of high-frequency variable flows in a wide range of velocities. The proposed modification allows the minimization of dynamic measurement errors.

  16. Delay dynamics of neuromorphic optoelectronic nanoscale resonators: Perspectives and applications

    Science.gov (United States)

    Romeira, Bruno; Figueiredo, José M. L.; Javaloyes, Julien

    2017-11-01

    With the recent exponential growth of applications using artificial intelligence (AI), the development of efficient and ultrafast brain-like (neuromorphic) systems is crucial for future information and communication technologies. While the implementation of AI systems using computer algorithms of neural networks is emerging rapidly, scientists are just taking the very first steps in the development of the hardware elements of an artificial brain, specifically neuromorphic microchips. In this review article, we present the current state of the art of neuromorphic photonic circuits based on solid-state optoelectronic oscillators formed by nanoscale double barrier quantum well resonant tunneling diodes. We address, both experimentally and theoretically, the key dynamic properties of recently developed artificial solid-state neuron microchips with delayed perturbations and describe their role in the study of neural activity and regenerative memory. This review covers our recent research work on excitable and delay dynamic characteristics of both single and autaptic (delayed) artificial neurons including all-or-none response, spike-based data encoding, storage, signal regeneration and signal healing. Furthermore, the neural responses of these neuromorphic microchips display all the signatures of extended spatio-temporal localized structures (LSs) of light, which are reviewed here in detail. By taking advantage of the dissipative nature of LSs, we demonstrate potential applications in optical data reconfiguration and clock and timing at high-speeds and with short transients. The results reviewed in this article are a key enabler for the development of high-performance optoelectronic devices in future high-speed brain-inspired optical memories and neuromorphic computing.

  17. Scanning tunneling microscopy studies of diamond films and optoelectronic materials

    Science.gov (United States)

    Perez, Jose M.

    1993-01-01

    In this report, we report on progress achieved from 12/1/92 to 10/1/93 under the grant entitled 'Scanning Tunneling Microscopy Studies of Diamond Films and Optoelectronic Materials'. We have set-up a chemical vapor deposition (CVD) diamond film growth system and a Raman spectroscopy system to study the nucleation and growth of diamond films with atomic resolution using scanning tunneling microscopy (STM). A unique feature of the diamond film growth system is that diamond films can be transferred directly to the ultrahigh vacuum (UHV) chamber of a scanning tunneling microscope without contaminating the films by exposure to air. The University of North Texas (UNT) provided $20,000 this year as matching funds for the NASA grant to purchase the diamond growth system. In addition, UNT provided a Coherent Innova 90S Argon ion laser, a Spex 1404 double spectrometer, and a Newport optical table costing $90,000 to set-up the Raman spectroscopy system. The CVD diamond growth system and Raman spectroscopy system will be used to grow and characterize diamond films with atomic resolution using STM as described in our proposal. One full-time graduate student and one full-time undergraduate student are supported under this grant. In addition, several graduate and undergraduate students were supported during the summer to assist in setting-up the diamond growth and Raman spectroscopy systems. We have obtained research results concerning STM of the structural and electronic properties of CVD grown diamond films, and STM and scanning tunneling spectroscopy of carbon nanotubes. In collaboration with the transmission electron microscopy (TEM) group at UNT, we have also obtained results concerning the optoelectronic material siloxene. These results were published in refereed scientific journals, submitted for publication, and presented as invited and contributed talks at scientific conferences.

  18. A Hybrid OFDM-TDM Architecture with Decentralized Dynamic Bandwidth Allocation for PONs

    Science.gov (United States)

    Cevik, Taner

    2013-01-01

    One of the major challenges of passive optical networks is to achieve a fair arbitration mechanism that will prevent possible collisions from occurring at the upstream channel when multiple users attempt to access the common fiber at the same time. Therefore, in this study we mainly focus on fair bandwidth allocation among users, and present a hybrid Orthogonal Frequency Division Multiplexed/Time Division Multiplexed architecture with a dynamic bandwidth allocation scheme that provides satisfying service qualities to the users depending on their varying bandwidth requirements. Unnecessary delays in centralized schemes occurring during bandwidth assignment stage are eliminated by utilizing a decentralized approach. Instead of sending bandwidth demands to the optical line terminal (OLT) which is the only competent authority, each optical network unit (ONU) runs the same bandwidth demand determination algorithm. ONUs inform each other via signaling channel about the status of their queues. This information is fed to the bandwidth determination algorithm which is run by each ONU in a distributed manner. Furthermore, Light Load Penalty, which is a phenomenon in optical communications, is mitigated by limiting the amount of bandwidth that an ONU can demand. PMID:24194684

  19. Coherence bandwidth characterization in an urban microcell at 62.4 GHz

    DEFF Research Database (Denmark)

    Sánchez, M. G.; Hammoudeh, A. M.; Grindrod, E.

    2000-01-01

    variation of this coefficient with distance and in order to provide accurate estimates of the coherence bandwidth in the microcell, the correlation coefficient has to be measured over large sections. Two methods to calculate the coherence bandwidth are presented and compared. It is shown that estimating...

  20. Task Mapping and Bandwidth Reservation for Mixed Hard/Soft Fault-Tolerant Embedded Systems

    DEFF Research Database (Denmark)

    Saraswat, Prabhat Kumar; Pop, Paul; Madsen, Jan

    2010-01-01

    In this paper we are interested in mixed hard/soft real-time fault-tolerant applications mapped on distributed heterogeneous architectures. We use the Earliest Deadline First (EDF) scheduling for the hard real-time tasks and the Constant Bandwidth Server (CBS) for the soft tasks. The bandwidth re...

  1. High-Q Variable Bandwidth Passive Filters for Software Defined Radio

    NARCIS (Netherlands)

    Arkesteijn, V.J.; Klumperink, Eric A.M.; Nauta, Bram

    2001-01-01

    An important aspect of Software Defined Radio is the ability to define the bandwidth of the filter that selects the desired channel. This paper describes a technique for channel filtering, in which two passive filters are combined to obtain a variable bandwidth. Passive filters have the advantage of

  2. High-Q variable bandwidth passive filters for Software Defined Radio

    NARCIS (Netherlands)

    Arkesteijn, V.J.; Klumperink, Eric A.M.; Nauta, Bram

    An important aspect of Software Defined Radio is the ability to define the bandwidth of the filter that selects the desired channel. This paper describes a technique for channel filtering, in which two passive filters are combined to obtain a variable bandwidth. Passive filters have the advantage of

  3. Comparison of Available Bandwidth Estimation Techniques in Packet-Switched Mobile Networks

    DEFF Research Database (Denmark)

    López Villa, Dimas; Ubeda Castellanos, Carlos; Teyeb, Oumer Mohammed

    2006-01-01

    of information regarding the available bandwidth in the transport network, as it could end up being the bottleneck rather than the air interface. This paper provides a comparative study of three well known available bandwidth estimation techniques, i.e. TOPP, SLoPS and pathChirp, taking into account...

  4. Investigation of Diagonal Antenna-Chassis Mode in Mobile Terminal LTE MIMO Antennas for Bandwidth Enhancement

    DEFF Research Database (Denmark)

    Zhang, Shuai; Zhao, Kun; Ying, Zhinong

    2015-01-01

    A diagonal antenna-chassis mode is investigated in long-term evolution multiple-input-multiple-output (LTE MIMO) antennas. The MIMO bandwidth is defined in this paper as the overlap range of the low-envelope correlation coefficient, high total efficiency, and -6-dB impedance matching bandwidths...

  5. Microwave photonic true time delay based on cross gain modulation in semiconductor optical amplifiers

    DEFF Research Database (Denmark)

    Xue, Weiqi; Mørk, Jesper

    2010-01-01

    We experimentally demonstrate microwave time delays in a semiconductor optical amplifier by cross gain modulation. In the counter-propagation configuration, ~10.5ps tunable true time delay over a microwave bandwidth of several tens of GHz is obtained.......We experimentally demonstrate microwave time delays in a semiconductor optical amplifier by cross gain modulation. In the counter-propagation configuration, ~10.5ps tunable true time delay over a microwave bandwidth of several tens of GHz is obtained....

  6. Optoelectronic device physics and technology of nitride semiconductors from the UV to the terahertz

    Science.gov (United States)

    Moustakas, Theodore D.; Paiella, Roberto

    2017-10-01

    This paper reviews the device physics and technology of optoelectronic devices based on semiconductors of the GaN family, operating in the spectral regions from deep UV to Terahertz. Such devices include LEDs, lasers, detectors, electroabsorption modulators and devices based on intersubband transitions in AlGaN quantum wells (QWs). After a brief history of the development of the field, we describe how the unique crystal structure, chemical bonding, and resulting spontaneous and piezoelectric polarizations in heterostructures affect the design, fabrication and performance of devices based on these materials. The heteroepitaxial growth and the formation and role of extended defects are addressed. The role of the chemical bonding in the formation of metallic contacts to this class of materials is also addressed. A detailed discussion is then presented on potential origins of the high performance of blue LEDs and poorer performance of green LEDs (green gap), as well as of the efficiency reduction of both blue and green LEDs at high injection current (efficiency droop). The relatively poor performance of deep-UV LEDs based on AlGaN alloys and methods to address the materials issues responsible are similarly addressed. Other devices whose state-of-the-art performance and materials-related issues are reviewed include violet-blue lasers, ‘visible blind’ and ‘solar blind’ detectors based on photoconductive and photovoltaic designs, and electroabsorption modulators based on bulk GaN or GaN/AlGaN QWs. Finally, we describe the basic physics of intersubband transitions in AlGaN QWs, and their applications to near-infrared and terahertz devices.

  7. Optoelectronic device physics and technology of nitride semiconductors from the UV to the terahertz.

    Science.gov (United States)

    Moustakas, Theodore D; Paiella, Roberto

    2017-10-01

    This paper reviews the device physics and technology of optoelectronic devices based on semiconductors of the GaN family, operating in the spectral regions from deep UV to Terahertz. Such devices include LEDs, lasers, detectors, electroabsorption modulators and devices based on intersubband transitions in AlGaN quantum wells (QWs). After a brief history of the development of the field, we describe how the unique crystal structure, chemical bonding, and resulting spontaneous and piezoelectric polarizations in heterostructures affect the design, fabrication and performance of devices based on these materials. The heteroepitaxial growth and the formation and role of extended defects are addressed. The role of the chemical bonding in the formation of metallic contacts to this class of materials is also addressed. A detailed discussion is then presented on potential origins of the high performance of blue LEDs and poorer performance of green LEDs (green gap), as well as of the efficiency reduction of both blue and green LEDs at high injection current (efficiency droop). The relatively poor performance of deep-UV LEDs based on AlGaN alloys and methods to address the materials issues responsible are similarly addressed. Other devices whose state-of-the-art performance and materials-related issues are reviewed include violet-blue lasers, 'visible blind' and 'solar blind' detectors based on photoconductive and photovoltaic designs, and electroabsorption modulators based on bulk GaN or GaN/AlGaN QWs. Finally, we describe the basic physics of intersubband transitions in AlGaN QWs, and their applications to near-infrared and terahertz devices.

  8. MATLAB implementation of a dynamic clamp with bandwidth >125 KHz capable of generating INa at 37°C

    Science.gov (United States)

    Clausen, Chris; Valiunas, Virginijus; Brink, Peter R.; Cohen, Ira S.

    2012-01-01

    We describe the construction of a dynamic clamp with bandwidth >125 KHz that utilizes a high performance, yet low cost, standard home/office PC interfaced with a high-speed (16 bit) data acquisition module. High bandwidth is achieved by exploiting recently available software advances (code-generation technology, optimized real-time kernel). Dynamic-clamp programs are constructed using Simulink, a visual programming language. Blocks for computation of membrane currents are written in the high-level matlab language; no programming in C is required. The instrument can be used in single- or dual-cell configurations, with the capability to modify programs while experiments are in progress. We describe an algorithm for computing the fast transient Na+ current (INa) in real time, and test its accuracy and stability using rate constants appropriate for 37°C. We then construct a program capable of supplying three currents to a cell preparation: INa, the hyperpolarizing-activated inward pacemaker current (If), and an inward-rectifier K+ current (IK1). The program corrects for the IR drop due to electrode current flow, and also records all voltages and currents. We tested this program on dual patch-clamped HEK293 cells where the dynamic clamp controls a current-clamp amplifier and a voltage-clamp amplifier controls membrane potential, and current-clamped HEK293 cells where the dynamic clamp produces spontaneous pacing behavior exhibiting Na+ spikes in otherwise passive cells. PMID:23224681

  9. Construction and experimental testing of the constant-bandwidth constant-temperature anemometer.

    Science.gov (United States)

    Ligeza, P

    2008-09-01

    A classical constant-temperature hot-wire anemometer enables the measurement of fast-changing flow velocity fluctuations, although its transmission bandwidth is a function of measured velocity. This may be a source of significant dynamic errors. Incorporation of an adaptive controller into the constant-temperature system results in hot-wire anemometer operating with a constant transmission bandwidth. The construction together with the results of experimental testing of a constant-bandwidth hot-wire anemometer prototype are presented in this article. During the testing, an approximately constant transmission bandwidth of the anemometer was achieved. The constant-bandwidth hot-wire anemometer can be used in measurements of high-frequency variable flows characterized by a wide range of velocity changes.

  10. Robust laser frequency stabilization by serrodyne modulation.

    Science.gov (United States)

    Kohlhaas, Ralf; Vanderbruggen, Thomas; Bernon, Simon; Bertoldi, Andrea; Landragin, Arnaud; Bouyer, Philippe

    2012-03-15

    We report the relative frequency stabilization of a distributed feedback erbium-doped fiber laser on an optical cavity by serrodyne frequency shifting. A correction bandwidth of 2.3 MHz and a dynamic range of 220 MHz are achieved, which leads to a strong robustness against large disturbances up to high frequencies. We demonstrate that serrodyne frequency shifting reaches a higher correction bandwidth and lower relative frequency noise level compared to a standard acousto-optical modulator based scheme. Our results allow us to consider promising applications in the absolute frequency stabilization of lasers on optical cavities.

  11. 47 CFR 2.1049 - Measurements required: Occupied bandwidth.

    Science.gov (United States)

    2010-10-01

    ... the equipment will be operated. The signal shall be applied through any filter networks, pseudo-random... deviation of the transmitter is measured when a test signal consisting of a band of random noise extending... exceed the modulation reference level by the number of decibels determined using the appropriate formula...

  12. Fixed tile rate codec for bandwidth saving in video processors

    Science.gov (United States)

    Lachine, Vladimir; Dinh, Chon-Tam Le; Le, Dinh Kha; Wong, Jeffrey

    2014-02-01

    The paper presents an image compression circuit for bandwidth saving in video display processors. This is intra frame tile based compression algorithm offering visually lossless quality for compression rates between 1.5 and 2.5. RGB and YCbCr (4:4:4, 4:2:2 and 4:2:0) video formats are supported for 8/10 bits video signals. The Band Width Compressor (BWC) consists of Lossless Compressor (LC) and Quantization Compressor (QC) that generate output bit streams for tiles of pixels. Size of output bit stream generated for a tile by the LC may be less or greater than a required size of output memory block. The QC generates bit stream that always fits output memory block of the required size. The output bit stream generated by the LC is transmitted if its size is less than the required size of the output memory block. Otherwise, the output bit stream generated by the QC is transmitted. The LC works on pixel basis. A difference between original and predicted pixel's values for each pixel of a tile is encoded as prefix and suffix. The prefix is encoded by means of variable length code, and suffix is encoded as is. The QC divides a tile of pixels on a set of blocks and quantizes pixels of each block independently of the other blocks. The number of quantization bits for all pixels of a block depends on standard deviation calculated over the block. A difference between pixel's value and average value over the block is quantized and transmitted.

  13. Extravehicular Activity Operations Concepts Under Communication Latency and Bandwidth Constraints

    Science.gov (United States)

    Beaton, Kara H.; Chappell, Steven P.; Abercromby, Andrew F. J.; Miller, Matthew J.; Nawotniak, Shannon Kobs; Hughes, Scott; Brady, Allyson; Lim, Darlene S. S.

    2017-01-01

    The Biologic Analog Science Associated with Lava Terrains (BASALT) project is a multi-year program dedicated to iteratively develop, implement, and evaluate concepts of operations (ConOps) and supporting capabilities intended to enable and enhance human scientific exploration of Mars. This pa-per describes the planning, execution, and initial results from the first field deployment, referred to as BASALT-1, which consisted of a series of 10 simulated extravehicular activities (EVAs) on volcanic flows in Idaho's Craters of the Moon (COTM) National Monument. The ConOps and capabilities deployed and tested during BASALT-1 were based on previous NASA trade studies and analog testing. Our primary research question was whether those ConOps and capabilities work acceptably when performing real (non-simulated) biological and geological scientific exploration under 4 different Mars-to-Earth communication conditions: 5 and 15 min one-way light time (OWLT) communication latencies and low (0.512 Mb/s uplink, 1.54 Mb/s downlink) and high (5.0 Mb/s uplink, 10.0 Mb/s downlink) bandwidth conditions representing the lower and higher limits of technical communication capabilities currently proposed for future human exploration missions. The synthesized results of BASALT-1 with respect to the ConOps and capabilities assessment were derived from a variety of sources, including EVA task timing data, network analytic data, and subjective ratings and comments regarding the scientific and operational acceptability of the ConOp and the extent to which specific capabilities were enabling and enhancing, and are presented here. BASALT-1 established preliminary findings that baseline ConOp, software systems, and communication protocols were scientifically and operationally acceptable with minor improvements desired by the "Mars" extravehicular (EV) and intravehicular (IV) crewmembers, but unacceptable with improvements required by the "Earth" Mission Support Center. These data will provide a

  14. X-(2) Modulator With 40-GHz Modulation Utilizing BaTiO3 Photonic Crystal Waveguides

    DEFF Research Database (Denmark)

    Girouard, Peter David; Chen, Pice; Jeong, Young Kyu

    2017-01-01

    Future telecommunication and data center networks as well as quantum optical communication systems will require optical modulators with wide bandwidths, large extinction, low operating voltage, and small size. We report the first quantitative demonstration of slow light enhancement of the electro...

  15. Integrated Graphene-Based Optoelectronic Devices Used for Ultrafast Optical-THz Photodetectors, Modulators and Emitters

    Science.gov (United States)

    2015-04-03

    electromagnetic radiation. 15. SUBJECT TERMS graphene , transport, imperfections or disorder, or impurities , conductance 16. SECURITY CLASSIFICATION OF...assumed to be present in doped graphene . We calculated the interaction energy between two magnetic impurities which are coupled via the indirect...determine the magnetic susceptibility in coordinate space. Analytic results are obtained for gapped graphene when the magnetic impurities were placed on

  16. Multirate diversity strategy of fractal modulation

    International Nuclear Information System (INIS)

    Yuan Yong; Shi Si-Hong; Luo Mao-Kang

    2011-01-01

    Previous analyses of fractal modulation were carried out mostly from a signle perspective or a subband, but the analyses from the perspective of multiscale synthesis have not been found yet; while multiscale synthesis is just the essence of the mutlirate diversity which is the most important characteristic of fractal modulation. As for the mutlirate diversity of fractal modulation, previous studies only dealt with the general outspread of its concept, lacked the thorough and intensive quantitative comparison and analysis. In light of the above fact, from the perspective of multiscale synthesis, in this paper we provide a comprehensive analysis of the multirate diversity of fractal modulation and corresponding quantitative analysis. The results show that mutlirate diversity, which is a fusion of frequency diversity and time diversity, pays an acceptable price in spectral efficiency in exchange for a significant improvement in bit error rate. It makes fractal modulation particularly suitable for the channels whose bandwidth and duration parameters are unknown or cannot be predicted to the transmitter. Surely it is clearly of great significance for reliable communications. Moreover, we also attain the ability to flexibly make various rate-bandwidth tradeoffs between the transmitter and the receiver, to freely select the reception time and to expediently control the total bandwidth. Furthermore, the acquisitions or improvements of these fine features could provide support of the technical feasibility for the electromagnetic spectrum control technology in a complex electromagnetic environment. (general)

  17. Knee implant imaging at 3 Tesla using high-bandwidth radiofrequency pulses.

    Science.gov (United States)

    Bachschmidt, Theresa J; Sutter, Reto; Jakob, Peter M; Pfirrmann, Christian W A; Nittka, Mathias

    2015-06-01

    To investigate the impact of high-bandwidth radiofrequency (RF) pulses used in turbo spin echo (TSE) sequences or combined with slice encoding for metal artifact correction (SEMAC) on artifact reduction at 3 Tesla in the knee in the presence of metal. Local transmit/receive coils feature increased maximum B1 amplitude, reduced SAR exposition and thus enable the application of high-bandwidth RF pulses. Susceptibility-induced through-plane distortion scales inversely with the RF bandwidth and the view angle, hence blurring, increases for higher RF bandwidths, when SEMAC is used. These effects were assessed for a phantom containing a total knee arthroplasty. TSE and SEMAC sequences with conventional and high RF bandwidths and different contrasts were tested on eight patients with different types of implants. To realize scan times of 7 to 9 min, SEMAC was always applied with eight slice-encoding steps and distortion was rated by two radiologists. A local transmit/receive knee coil enables the use of an RF bandwidth of 4 kHz compared with 850 Hz in conventional sequences. Phantom scans confirm the relation of RF bandwidth and through-plane distortion, which can be reduced up to 79%, and demonstrate the increased blurring for high-bandwidth RF pulses. In average, artifacts in this RF mode are rated hardly visible for patients with joint arthroplasties, when eight SEMAC slice-encoding steps are applied, and for patients with titanium fixtures, when TSE is used. The application of high-bandwidth RF pulses by local transmit coils substantially reduces through-plane distortion artifacts at 3 Tesla. © 2014 Wiley Periodicals, Inc.

  18. 78 FR 16296 - Certain Optoelectronic Devices for Fiber Optic Communications, Components Thereof, and Products...

    Science.gov (United States)

    2013-03-14

    ... Fiber Optic Communications, Components Thereof, and Products Containing Same; Commission Determination... United States after importation of certain optoelectronic devices for fiber optic communications... Fiber IP (Singapore) Pte. Ltd. of Singapore (``Avago Fiber IP''); Avago General IP and Avago...

  19. GaN nano-membrane for optoelectronic and electronic device applications

    KAUST Repository

    Ooi, Boon S.

    2014-01-01

    The ~25nm thick threading dislocation free GaN nanomembrane was prepared using ultraviolet electroless chemical etching method offering the possibility of flexible integration of (Al,In,Ga)N optoelectronic and electronic devices.

  20. Increasing the bandwidth of resonant gravitational antennas The case of Explorer

    CERN Document Server

    Astone, P; Bassan, M; Carelli, P; Cavallari, Giorgio; Coccia, E; Cosmelli, C; D'Antonio, S; Fafone, V; Fauth, A C; Federici, G; Giordano, G; Marini, A; Minenkov, Y; Modena, I; Modestino, G; Moleti, A; Pallottino, G V; Pizzella, G; Quintieri, L; Rocchi, A; Ronga, F; Terenzi, R; Torrioli, G; Visco, M

    2003-01-01

    Resonant gravitational wave detectors with an observation bandwidth of tens of hertz are a reality: the antenna Explorer, operated at CERN by the ROG collaboration, has been upgraded with a new read-out. In this new configuration, it exhibits an unprecedented useful bandwidth: in over 55 Hz about its frequency of operation of 919 Hz the spectral sensitivity is better than 10^{-20} /sqrt(Hz) . We describe the detector and its sensitivity and discuss the foreseable upgrades to even larger bandwidths.

  1. Bandwidth Study on Energy Use and Potential Energy Saving Opportunities in U.S. Chemical Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Sabine Brueske, Caroline Kramer, Aaron Fisher

    2015-06-01

    Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. chemical manufacturing. The study relies on multiple sources to estimate the energy used in the production of 74 individual chemicals, representing 57% of sector-wide energy consumption. Energy savings opportunities for individual chemicals and for 15 subsectors of chemicals manufacturing are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

  2. Bandwidth Study on Energy Use and Potential Energy Savings Opportunities in U.S. Petroleum Refining

    Energy Technology Data Exchange (ETDEWEB)

    Sabine Brueske, Caroline Kramer, Aaron Fisher

    2015-06-01

    Energy bandwidth studies of U.S. manufacturing sectors can serve as foundational references in framing the range (or bandwidth) of potential energy savings opportunities. This bandwidth study examines energy consumption and potential energy savings opportunities in U.S. petroleum refining. The study relies on multiple sources to estimate the energy used in nine individual process areas, representing 68% of sector-wide energy consumption. Energy savings opportunities for individual processes are based on technologies currently in use or under development; these potential savings are then extrapolated to estimate sector-wide energy savings opportunity.

  3. Acousto-optics bandwidth broadening in a Bragg cell based on arbitrary synthesized signal methods.

    Science.gov (United States)

    Peled, Itay; Kaminsky, Ron; Kotler, Zvi

    2015-06-01

    In this work, we present the advantages of driving a multichannel acousto-optical deflector (AOD) with a digitally synthesized multifrequency RF signal. We demonstrate a significant bandwidth broadening of ∼40% by providing well-tuned phase control of the array transducers. Moreover, using a multifrequency, complex signal, we manage to suppress the harmonic deflections and return most of the spurious energy to the main beam. This method allows us to operate the AOD with more than an octave of bandwidth with negligible spurious energy going to the harmonic beams and a total bandwidth broadening of over 70%.

  4. Surface engineered two-dimensional and quasi-one-dimensional nanomaterials for electronic and optoelectronic devices

    Science.gov (United States)

    Du, Xiang

    As the sizes of individual components in electronic and optoelectronic devices approach nano scale, the performance of the devices is often determined by surface properties due to their large surface-to-volume ratio. Surface phenomena have become one of the cornerstones in nanoelectronic industry. For this reason, research on the surface functionalization has been tremendous amount of growth over the past decades, and promises to be an increasingly important field in the future. Surface functionalization, as an effective technique to modify the surface properties of a material through a physical or chemical approach, exhibits great potential to solve the problems and challenges, and modulate the performance of nanomaterials based functional devices. Surface functionalization drives the developments and applications of modern electronic and optoelectronic devices fabricated by nanomaterials. In this thesis, I demonstrate two surface functionalization approaches, namely, surface transfer doping and H2 annealing, to effectively solve the problems and significantly enhance the performance of 2D (single structure black phosphorus (BP) and heterostructure graphene/Si Schottky junction), and quasi-1D (molybdenum trioxide (MoO 3) nanobelt) nanomaterials based functional devices, respectively. In situ photoelectron spectroscopy (PES) measurements were also carried out to explore the interfacial charge transfer occurring at the interface between the nanostructures and doping layers, and the gap states in MoO 3 thin films, which provides the underlying mechanism to understand and support our device measurement results. In the first part of this thesis, I will discuss the first surface functionalization approach, namely, surface transfer doping, to effectively modulate the ambipolar characteristics of 2D few-layer BP flakes based FETs. The ambipolar characteristics of BP transistors were effectively modulated through in situ surface functionalization with cesium carbonate (Cs2

  5. A multi-GHz chaotic optoelectronic oscillator based on laser terminal voltage

    International Nuclear Information System (INIS)

    Chang, C. Y.; Choi, Daeyoung; Locquet, A.; Wishon, Michael J.; Citrin, D. S.; Merghem, K.; Ramdane, Abderrahim; Martinez, A.; Lelarge, François

    2016-01-01

    A multi-GHz chaotic optoelectronic oscillator based on an external cavity semiconductor laser (ECL) is demonstrated. Unlike the standard optoelectronic oscillators for microwave applications, we do not employ the dynamic light output incident on a photodiode to generate the microwave signal, but instead generate the microwave signal directly by measuring the terminal voltage V(t) of the laser diode of the ECL under constant-current operation, thus obviating the photodiode entirely.

  6. Impact of gate fan-in and fan-out limits on optoelectronic digital circuits.

    Science.gov (United States)

    Ji, L; Heuring, V P

    1997-06-10

    The impact of gate fan-in and fan-out limits on digital circuit delay is discussed with a set of benchmark circuits. This research presents the advantages of exploiting the ability of optoelectronic gates to perform both logic operations and optical interconnections with systematic optimization. It is possible for gate-level optical interconnected optoelectronic circuits to compete with their pure silicon counterparts in terms of the combinational circuit delay and system clock rate.

  7. Performance Evaluation of an Optoelectronic Oscillator Based on a Band-Pass Microwave Photonic Filter Architecture

    OpenAIRE

    A. G. Correa-Mena; I. E. Zaldivar-Huerta; M. W. Lee; A. Garcia-Juarez; L. A. Garcia-Delgado

    2017-01-01

    The experimental performance evaluation of an optoelectronic oscillator based on a band-pass microwave photonic filter architecture is carried out. The novelty of this proposal resides in the fact that the architecture used allows enhancing the free spectral range of the optoelectronic oscillator. Considering the optical spectral characteristics of the multimode laser diode used as an optical source, the length and the chromatic dispersion parameter of the optical fiber which acts as a feedba...

  8. Optoelectronic Picosecond Detection of Synchrotron X-rays

    Energy Technology Data Exchange (ETDEWEB)

    Durbin, Stephen M. [Purdue Univ., West Lafayette, IN (United States)

    2017-08-04

    The goal of this research program was to develop a detector that would measure x-ray time profiles with picosecond resolution. This was specifically aimed for use at x-ray synchrotrons, where x-ray pulse profiles have Gaussian time spreads of 50-100 ps (FWHM), so the successful development of such a detector with picosecond resolution would permit x-ray synchrotron studies to break through the pulse width barrier. That is, synchrotron time-resolved studies are currently limited to pump-probe studies that cannot reveal dynamics faster than ~50 ps, whereas the proposed detector would push this into the physically important 1 ps domain. The results of this research effort, described in detail below, are twofold: 1) the original plan to rely on converting electronic signals from a semiconductor sensor into an optical signal proved to be insufficient for generating signals with the necessary time resolution and sensitivity to be widely applicable; and 2) an all-optical method was discovered whereby the x-rays are directly absorbed in an optoelectronic material, lithium tantalate, which can then be probed by laser pulses with the desired picosecond sensitivity for detection of synchrotron x-rays. This research program has also produced new fundamental understanding of the interaction of x-rays and optical lasers in materials that has now created a viable path for true picosecond detection of synchrotron x-rays.

  9. Technical quality assessment of an optoelectronic system for movement analysis

    International Nuclear Information System (INIS)

    Sapienza University of Rome (Italy))" data-affiliation=" (Department of Mechanical and Aerospace Engineering, Sapienza University of Rome (Italy))" >Di Marco, R; Sapienza University of Rome (Italy))" data-affiliation=" (Department of Mechanical and Aerospace Engineering, Sapienza University of Rome (Italy))" >Patanè, F; Sapienza University of Rome (Italy))" data-affiliation=" (Department of Mechanical and Aerospace Engineering, Sapienza University of Rome (Italy))" >Cappa, P; Rossi, S

    2015-01-01

    The Optoelectronic Systems (OS) are largely used in gait analysis to evaluate the motor performances of healthy subjects and patients. The accuracy of marker trajectories reconstruction depends on several aspects: the number of cameras, the dimension and position of the calibration volume, and the chosen calibration procedure. In this paper we propose a methodology to evaluate the effects of the mentioned sources of error on the reconstruction of marker trajectories. The novel contribution of the present work consists in the dimension of the tested calibration volumes, which is comparable with the ones normally used in gait analysis; in addition, to simulate trajectories during clinical gait analysis, we provide non-default paths for markers as inputs. Several calibration procedures are implemented and the same trial is processed with each calibration file, also considering different cameras configurations. The RMSEs between the measured trajectories and the optimal ones are calculated for each comparison. To investigate the significant differences between the computed indices, an ANOVA analysis is implemented. The RMSE is sensible to the variations of the considered calibration volume and the camera configurations and it is always inferior to 43 mm

  10. Transferrable monolithic III-nitride photonic circuit for multifunctional optoelectronics

    Science.gov (United States)

    Shi, Zheng; Gao, Xumin; Yuan, Jialei; Zhang, Shuai; Jiang, Yan; Zhang, Fenghua; Jiang, Yuan; Zhu, Hongbo; Wang, Yongjin

    2017-12-01

    A monolithic III-nitride photonic circuit with integrated functionalities was implemented by integrating multiple components with different functions into a single chip. In particular, the III-nitride-on-silicon platform is used as it integrates a transmitter, a waveguide, and a receiver into a suspended III-nitride membrane via a wafer-level procedure. Here, a 0.8-mm-diameter suspended device architecture is directly transferred from silicon to a foreign substrate by mechanically breaking the support beams. The transferred InGaN/GaN multiple-quantum-well diode (MQW-diode) exhibits a turn-on voltage of 2.8 V with a dominant electroluminescence peak at 453 nm. The transmitter and receiver share an identical InGaN/GaN MQW structure, and the integrated photonic circuit inherently works for on-chip power monitoring and in-plane visible light communication. The wire-bonded monolithic photonic circuit on glass experimentally demonstrates in-plane data transmission at 120 Mb/s, paving the way for diverse applications in intelligent displays, in-plane light communication, flexible optical sensors, and wearable III-nitride optoelectronics.

  11. Laser processing of components for polymer mircofluidic and optoelectronic products

    Science.gov (United States)

    Gillner, Arnold; Bremus-Koebberling, Elke A.; Wehner, Martin; Russek, Ulrich A.; Berden, Thomas

    2001-06-01

    Miniaturization is one of the keywords for the production of customer oriented and highly integrated consumer products like mobile phones, portables and other products from the daily life and there are some first silicon made products like pressure sensors, acceleration sensors and micro fluidic components, which are built in automobiles, washing machines and medical products. However, not all applications can be covered with this material, because of the limitations in lateral and 3-dimensional structuring, the mechanical behavior, the functionality and the costs of silicon. Therefore other materials, like polymers have been selected as suitable candidates for cost effective mass products. This holds especially for medical and optical applications, where the properties of selected polymers, like biocompatibility, inert chemical behavior and high transparency can be used. For this material laser micro processing offers appropriate solutions for structuring as well as for packaging with high flexibility, material variety, structure size, processing speed and easy integration into existing fabrication plants. The paper presents recent results and industrial applications of laser micro processing for polymer micro fluidic devices, like micro analysis systems, micro reactors and medical micro implants, where excimer radiation is used for lateral structuring and diode lasers have used for joining and packaging. Similar technologies have been applied to polymer waveguides to produce passive optoelectronic components for high speed interconnection with surface roughness less than 20 nm and low attenuation. The paper also reviews the technical and economical limitations and the potential of the technology for other micro products.

  12. Flexible Synthetic Semiconductor Applied in Optoelectronic Organic Sensor

    Directory of Open Access Journals (Sweden)

    Andre F. S. Guedes

    2017-06-01

    Full Text Available The synthesis and application of new nanostructured organic materials, for the development of technology based on organic devices, have taken great interest from the scientific community. The greatest interest in studying organic semiconductor materials has been connected to its already known potential applications, such as: batteries, organic solar cells, flexible organic solar cells, organic light emitting diodes, organic sensors and others. Phototherapy makes use of different radiation sources, and the treatment of hyperbilirubinemia the most common therapeutic intervention occurs in the neonatal period. In this work we developed an organic optoelectronic sensor capable of detecting and determining the radiation dose rate emitted by the radiation source of neonatal phototherapy equipment. The sensors were developed using optically transparent substrate with Nanostructured thin film layers of Poly(9-Vinylcarbazole covered by a layer of Poly(P-Phenylene Vinylene. The samples were characterized by UV-Vis Spectroscopy, Electrical Measurements and SEM. With the results obtained from this study can be developed dosimeters organics to the neonatal phototherapy equipment.

  13. Light Management in Optoelectronic Devices with Disordered and Chaotic Structures

    KAUST Repository

    Khan, Yasser

    2012-07-01

    With experimental realization, energy harvesting capabilities of chaotic microstructures were explored. Incident photons falling into chaotic trajectories resulted in energy buildup for certain frequencies. As a consequence, many fold enhancement in light trapping was observed. These ellipsoid like chaotic microstructures demonstrated 25% enhancement in light trapping at 450nm excitation and 15% enhancement at 550nm excitation. Optimization of these structures can drive novel chaos-assisted energy harvesting systems. In subsequent sections of the thesis, prospect of broadband light extraction from white light emitting diodes were investigated, which is an unchallenged but quintessential problem in solid-state lighting. Size dependent scattering allows microstructures to interact strongly with narrow-band light. If disorder is introduced in spread and sizes of microstructures, broadband light extraction is possible. A novel scheme with Voronoi tessellation to quantify disorder in physical systems was also introduced, and a link between voronoi disorder and state disorder of statistical mechanics was established. Overall, in this thesis some nascent concepts regarding disorder and chaos were investigated to efficiently manage electromagnetic waves in optoelectronic devices.

  14. Optoelectronic properties of doped hydrothermal ZnO thin films

    KAUST Repository

    Mughal, Asad J.

    2017-03-10

    Group III impurity doped ZnO thin films were deposited on MgAl2O3 substrates using a simple low temperature two-step deposition method involving atomic layer deposition and hydrothermal epitaxy. Films with varying concentrations of either Al, Ga, or In were evaluated for their optoelectronic properties. Inductively coupled plasma atomic emission spectroscopy was used to determine the concentration of dopants within the ZnO films. While Al and Ga-doped films showed linear incorporation rates with the addition of precursors salts in the hydrothermal growth solution, In-doped films were shown to saturate at relatively low concentrations. It was found that Ga-doped films showed the best performance in terms of electrical resistivity and optical absorbance when compared to those doped with In or Al, with a resistivity as low as 1.9 mΩ cm and an optical absorption coefficient of 441 cm−1 at 450 nm.

  15. Recent Achievements on Photovoltaic Optoelectronic Tweezers Based on Lithium Niobate

    Directory of Open Access Journals (Sweden)

    Angel García-Cabañes

    2018-01-01

    Full Text Available This review presents an up-dated summary of the fundamentals and applications of optoelectronic photovoltaic tweezers for trapping and manipulation of nano-objects on the surface of lithium niobate crystals. It extends the contents of previous reviews to cover new topics and developments which have emerged in recent years and are marking the trends for future research. Regarding the theoretical description of photovoltaic tweezers, detailed simulations of the electrophoretic and dielectrophoretic forces acting on different crystal configurations are discussed in relation to the structure of the obtained trapping patterns. As for the experimental work, we will pay attention to the manipulation and patterning of micro-and nanoparticles that has experimented an outstanding progress and relevant applications have been reported. An additional focus is now laid on recent work about micro-droplets, which is a central topic in microfluidics and optofluidics. New developments in biology and biomedicine also constitute a relevant part of the review. Finally, some topics partially related with photovoltaic tweezers and a discussion on future prospects and challenges are included.

  16. Bismuth Silver Oxysulfide for Photoconversion Applications: Structural and Optoelectronic Properties

    KAUST Repository

    Baqais, Amal Ali Abdulallh

    2017-09-18

    Single-phase bismuth silver oxysulfide, BiAgOS, was prepared by a hydrothermal method. Its structural, morphological and optoelectronic properties were investigated and compared with bismuth copper oxysulfide (BiCuOS). Rietveld refinement of the powder X-ray diffraction (XRD) measurements revealed that the BiAgOS and BiCuOS crystals have the same structure as ZrSiCuAs: the tetragonal space group P4/nmm. X-ray photoelectron spectroscopy (XPS) analyses confirmed that the BiAgOS has a high purity, in contrast with BiCuOS, which tends to have Cu vacancies. The Ag has a monovalent oxidation state, whereas Cu is present in the oxidation states of +1 and +2 in the BiCuOS system. Combined with experimental measurements, density functional theory calculations employing the range-separated hybrid HSE06 exchange-correlation functional with spin-orbit coupling quantitatively elucidated photophysical properties such as ab-sorption coefficients, effective masses and dielectric constants. BiCuOS and BiAgOS were found to have indirect bandgaps of 1.1 and 1.5 eV, respectively. Both possess high dielectric constants and low electron and hole effective masses. Therefore, these materials are expected to have high exciton dissociation capabilities and excellent carrier diffusion properties. This study reveals that BiAgOS is a promising candidate for photoconversion applications.

  17. Optoelectronic properties of four azobenzene-based iminopyridine ligands for photovoltaic application

    Directory of Open Access Journals (Sweden)

    Aziz El alamy

    2017-11-01

    Full Text Available Because of organic π-conjugated materials’ optoelectronic properties and potential applications in a wide range of electronic and optoelectronic devices, such as organic solar cells, these materials, including both polymers and oligomers, have been widely studied in recent years. This work reposts a theoretical study using the DFT method on four azobenzene-based iminopyridines. The theoretical ground-state geometry, electronic structure and optoelectronic parameters (highest occupied molecular orbital (HOMO, lowest unoccupied molecular orbital (LUMO energy levels, open-circuit voltage (Voc and oscillator strengths (O.S of the studied molecules were obtained using the density functional theory (DFT and time-dependent (TDDFT approaches. The effects of the structure length and substituents on the geometric and optoelectronic properties of these materials are discussed to investigate the relationship between the molecular structure and the optoelectronic properties. The results of this study are consistent with the experimental ones and suggest that these materials as good candidates for use in photovoltaic devices. Keywords: π-conjugated materials, azobenzene, optoelectronic properties, DFT calculations, HOMO-LUMO gap

  18. Low-voltage, high-speed and compact electro-absorption modulator laterally integrated with 980-nm VCSEL.

    Science.gov (United States)

    Dalir, Hamed; Takahashi, Yuta; Koyama, Fumio

    2014-10-20

    We present a compact electro-absorption slow-light modulator laterally-integrated with a 980-nm VCSEL. We figured out the small signal modulation response for different modulator lengths. While the 3-dB small-signal modulation bandwidth of conventional directly modulated VCSELs on the same epi-wafer structure was limited below 10 GHz, we obtained a modulation bandwidth over 21 GHz for a 30 µm long modulator. We also demonstrated large signal modulation up to 25 Gbps with a low driving voltage below 600 mV(pp) and an extinction ratio of 4 dB for the modulator length of 50 µm. Prospects of much higher speed (> 40 Gbps) were examined with reducing the size of the modulator. Also, the tapered waveguide coupling structure enables "quasi-unidirectional coupling", which reduces the optical feedback in a VCSEL from the integrated modulator.

  19. Terahertz bandwidth photonic Hilbert transformers based on synthesized planar Bragg grating fabrication.

    Science.gov (United States)

    Sima, Chaotan; Gates, J C; Holmes, C; Mennea, P L; Zervas, M N; Smith, P G R

    2013-09-01

    Terahertz bandwidth photonic Hilbert transformers are proposed and experimentally demonstrated. The integrated device is fabricated via a direct UV grating writing technique in a silica-on-silicon platform. The photonic Hilbert transformer operates at bandwidths of up to 2 THz (~16 nm) in the telecom band, a 10-fold greater bandwidth than any previously reported experimental approaches. Achieving this performance requires detailed knowledge of the system transfer function of the direct UV grating writing technique; this allows improved linearity and yields terahertz bandwidth Bragg gratings with improved spectral quality. By incorporating a flat-top reflector and Hilbert grating with a waveguide coupler, an ultrawideband all-optical single-sideband filter is demonstrated.

  20. Estimating individual listeners’ auditory-filter bandwidth in simultaneous and non-simultaneous masking

    DEFF Research Database (Denmark)

    Buchholz, Jörg; Caminade, Sabine; Strelcyk, Olaf

    2010-01-01

    Frequency selectivity in the human auditory system is often measured using simultaneous masking of tones presented in notched noise. Based on such masking data, the equivalent rectangular bandwidth (ERB) of the auditory filters can be derived by applying the power spectrum model of masking....... Considering bandwidth estimates from previous studies based on forward masking, only average data across a number of subjects have been considered. The present study is concerned with bandwidth estimates in simultaneous and forward masking in individual normal-hearing subjects. In order to investigate...... the reliability of the individual estimates, a statistical resampling method is applied. It is demonstrated that a rather large set of experimental data is required to reliably estimate auditory filter bandwidth, particularly in the case of simultaneous masking. The poor overall reliability of the filter...

  1. Kernel bandwidth estimation for non-parametric density estimation: a comparative study

    CSIR Research Space (South Africa)

    Van der Walt, CM

    2013-12-01

    Full Text Available We investigate the performance of conventional bandwidth estimators for non-parametric kernel density estimation on a number of representative pattern-recognition tasks, to gain a better understanding of the behaviour of these estimators in high...

  2. Bandwidth Controllable Tunable Filter for Hyper-/Multi-Spectral Imager, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR Phase I proposal introduces a fast speed bandwidth controllable tunable filter for hyper-/multi-spectral (HS/MS) imagers. It dynamically passes a variable...

  3. Improvement of delay-bandwidth product in photonic crystal slow-light waveguides.

    Science.gov (United States)

    Hao, Ran; Cassan, Eric; Le Roux, Xavier; Gao, Dingshan; Do Khanh, Van; Vivien, Laurent; Marris-Morini, Delphine; Zhang, Xinliang

    2010-08-02

    We report new results about the improvement of delay-bandwidth product in photonic crystal slow light waveguides. Previous studies have obtained large delay-bandwidth product at the price of small average group index. It is pointed out here that the radius and the distance between the two boundary rows of holes have a key contribution for delay-bandwidth product. We show the possibility of improving this factor of merit meanwhile maintaining the same group index. We succeed in improving normal delay-bandwidth product from 0.15 to 0.35, keeping at the same time the group index unchanged at high value of 90. This optimization approach may be applicable for previous flat band slow light devices.

  4. High-Bandwidth Photon-Counting Detectors with Enhanced Near-Infrared Response Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Laser optical communications offer the potential to dramatically increase the link bandwidth and decrease the emitter power in long-range space communications....

  5. Single-channel labyrinthine metasurfaces as perfect sound absorbers with tunable bandwidth

    Science.gov (United States)

    Liu, Liu; Chang, Huiting; Zhang, Chi; Hu, Xinhua

    2017-08-01

    Perfect sound absorbers with a deep-subwavelength thickness are important to applications such as noise reduction and sound detection. But their absorption bandwidths are usually narrow and difficult to adjust. A recent solution for this problem relies on multiple-resonator metasurfaces, which are hard to fabricate. Here, we report on the design, fabrication, and characterization of a single-channel labyrinthine metasurface, which allows total sound absorption at resonant frequency when appropriate amounts of porous media (or critical sound losses) are introduced in the channels. The absorption bandwidth can be tuned by changing the cross-sectional areas of channels. A tradeoff is found between the absorption bandwidth and the metasurface thickness. However, large tunability in the relative absorption bandwidth (from 17% to 121%) is still attainable by such metasurfaces with a deep-subwavelength thickness (0.03-0.13λ).

  6. A 750MHz and a 8GHz High Bandwidth Digital FFT Spectrometer, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — The scope of this project is to to develop a wide bandwidth, low power, and compact single board digital Fast Fourier Transform spectrometer (FFTS) optimized for the...

  7. Radiation Hard High Performance Optoelectronic Devices, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — High-performance, radiation-hard, widely-tunable integrated laser/modulator chip and large-area avalanche photodetectors (APDs) are key components of optical...

  8. Integrated Optoelectronic Switching Technology for Fiber-Optic Communications Networks

    National Research Council Canada - National Science Library

    Fan, Regis

    1998-01-01

    .... most of the effort in optical amplifier switch modules have been focused on monolithic switches in which the entire device is fabricated on an InP substrate together with the semiconductor optical amplifiers (SOAs...

  9. Achieving increased bandwidth for 4 degree of freedom self-tuning energy harvester

    Science.gov (United States)

    Staaf, L. G. H.; Smith, A. D.; Köhler, E.; Lundgren, P.; Folkow, P. D.; Enoksson, P.

    2018-04-01

    The frequency response of a self-tuning energy harvester composed of two piezoelectric cantilevers connected by a middle beam with a sliding mass is investigated. Measurements show that incorporation of a free-sliding mass increases the bandwidth. Using an analytical model, the system is explained through close investigation of the resonance modes. Resonance mode behavior further suggests that, by breaking the symmetry of the system, even broader bandwidths are achievable.

  10. Coarse-Grain Bandwidth Estimation Techniques for Large-Scale Space Network

    Science.gov (United States)

    Cheung, Kar-Ming; Jennings, Esther

    2013-01-01

    In this paper, we describe a top-down analysis and simulation approach to size the bandwidths of a store-andforward network for a given network topology, a mission traffic scenario, and a set of data types with different latency requirements. We use these techniques to estimate the wide area network (WAN) bandwidths of the ground links for different architecture options of the proposed Integrated Space Communication and Navigation (SCaN) Network.

  11. Coarse-grain bandwidth estimation techniques for large-scale network

    Science.gov (United States)

    Cheung, Kar-Ming; Jennings, E.

    In this paper, we describe a top-down analysis and simulation approach to size the bandwidths of a store-and-forward network for a given network topology, a mission traffic scenario, and a set of data types with different latency requirements. We use these techniques to estimate the wide area network (WAN) bandwidths of the ground links for different architecture options of the proposed Integrated Space Communication and Navigation (SCaN) Network.

  12. Tuning gain and bandwidth of traveling wave tubes using metamaterial beam-wave interaction structures

    International Nuclear Information System (INIS)

    Lipton, Robert; Polizzi, Anthony

    2014-01-01

    We employ metamaterial beam-wave interaction structures for tuning the gain and bandwidth of short traveling wave tubes. The interaction structures are made from metal rings of uniform cross section, which are periodically deployed along the length of the traveling wave tube. The aspect ratio of the ring cross sections is adjusted to control both gain and bandwidth. The frequency of operation is controlled by the filling fraction of the ring cross section with respect to the size of the period cell.

  13. Can abnormal returns be earned on bandwidth-bounded currencies? Evidence from a genetic algorithm

    OpenAIRE

    Pedro Godinho

    2012-01-01

    Most of the studies about the Foreign Exchange market (Forex) analyse the behaviour of currencies that are allowed to float freely (or almost freely), but some currencies are still bounded by bandwidths (either disclosed or undisclosed). In this paper, I try to find out whether two bandwidth-bounded currencies, the Hong Kong dollar (HKD) and the Singapore dollar (SGD), present opportunities for abnormal returns. I consider a set of trading rules, and I use a genetic algorithm to optimise both...

  14. THE IMPROVEMENT OF COMPUTER NETWORK PERFORMANCE WITH BANDWIDTH MANAGEMENT IN KEMURNIAN II SENIOR HIGH SCHOOL

    Directory of Open Access Journals (Sweden)

    Bayu Kanigoro

    2012-05-01

    Full Text Available This research describes the improvement of computer network performance with bandwidth management in Kemurnian II Senior High School. The main issue of this research is the absence of bandwidth division on computer, which makes user who is downloading data, the provided bandwidth will be absorbed by the user. It leads other users do not get the bandwidth. Besides that, it has been done IP address division on each room, such as computer, teacher and administration room for supporting learning process in Kemurnian II Senior High School, so wireless network is needed. The method is location observation and interview with related parties in Kemurnian II Senior High School, the network analysis has run and designed a new topology network including the wireless network along with its configuration and separation bandwidth on microtic router and its limitation. The result is network traffic on Kemurnian II Senior High School can be shared evenly to each user; IX and IIX traffic are separated, which improve the speed on network access at school and the implementation of wireless network.Keywords: Bandwidth Management; Wireless Network

  15. On Bandwidth Characteristics of Tuning Fork Micro-Gyroscope with Mechanically Coupled Sense Mode

    Directory of Open Access Journals (Sweden)

    Yunfang Ni

    2014-07-01

    Full Text Available The bandwidth characteristics of a tuning fork micro-gyroscope with mechanically coupled sense mode were investigated in this paper to provide some references for mechanical bandwidth design. The concept of sense mode mechanical coupling is introduced first. Theoretical frequency response analyses were then carried out on the mechanical part of the gyroscope. Equations representing the relationships between the differential output signal and the frequency of the input angular rate were deduced in full frequency range and further simplified in low frequency range. Based on these equations, bandwidth characteristics under ideal and non-ideal conditions are discussed. Analytical results show that under ideal conditions, the bandwidth characteristics of a tuning fork micro-gyroscope are similar to those of a single mass micro-gyroscope, but under non-ideal conditions, especially when sense mass and/or stiffness are asymmetric, the bandwidth characteristics would be quite different because the in-phase mode would participate in the anti-phase vibration response. Experimental verifications were carried out on two micro-gyroscope prototypes designed in our laboratory. The deduced equations and analytical results can be used in guiding the mechanical bandwidth design of tuning fork micro-gyroscopes with mechanically coupled sense mode.

  16. Multi-granularity Bandwidth Allocation for Large-Scale WDM/TDM PON

    Science.gov (United States)

    Gao, Ziyue; Gan, Chaoqin; Ni, Cuiping; Shi, Qiongling

    2017-12-01

    WDM (wavelength-division multiplexing)/TDM (time-division multiplexing) PON (passive optical network) is being viewed as a promising solution for delivering multiple services and applications, such as high-definition video, video conference and data traffic. Considering the real-time transmission, QoS (quality of services) requirements and differentiated services model, a multi-granularity dynamic bandwidth allocation (DBA) in both domains of wavelengths and time for large-scale hybrid WDM/TDM PON is proposed in this paper. The proposed scheme achieves load balance by using the bandwidth prediction. Based on the bandwidth prediction, the wavelength assignment can be realized fairly and effectively to satisfy the different demands of various classes. Specially, the allocation of residual bandwidth further augments the DBA and makes full use of bandwidth resources in the network. To further improve the network performance, two schemes named extending the cycle of one free wavelength (ECoFW) and large bandwidth shrinkage (LBS) are proposed, which can prevent transmission from interruption when the user employs more than one wavelength. The simulation results show the effectiveness of the proposed scheme.

  17. MPTCP Tunnel: An Architecture for Aggregating Bandwidth of Heterogeneous Access Networks

    Directory of Open Access Journals (Sweden)

    Xiaolan Liu

    2018-01-01

    Full Text Available Fixed and cellular networks are two typical access networks provided by operators. Fixed access network is widely employed; nevertheless, its bandwidth is sometimes not sufficient enough to meet user bandwidth requirements. Meanwhile, cellular access network owns unique advantages of wider coverage, faster increasing link speed, more flexible deployment, and so forth. Therefore, it is attractive for operators to mitigate the bandwidth shortage by bundling these two. Actually, there have been existing schemes proposed to aggregate the bandwidth of two access networks, whereas they all have their own problems, like packet reordering or extra latency overhead. To address this problem, we design new architecture, MPTCP Tunnel, to aggregate the bandwidth of multiple heterogeneous access networks from the perspective of operators. MPTCP Tunnel uses MPTCP, which solves the reordering problem essentially, to bundle multiple access networks. Besides, MPTCP Tunnel sets up only one MPTCP connection at play which adapts itself to multiple traffic types and TCP flows. Furthermore, MPTCP Tunnel forwards intact IP packets through access networks, maintaining the end-to-end TCP semantics. Experimental results manifest that MPTCP Tunnel can efficiently aggregate the bandwidth of multiple access networks and is more adaptable to the increasing heterogeneity of access networks than existing mechanisms.

  18. Compression of Video Tracking and Bandwidth Balancing Routing in Wireless Multimedia Sensor Networks

    Directory of Open Access Journals (Sweden)

    Yin Wang

    2015-12-01

    Full Text Available There has been a tremendous growth in multimedia applications over wireless networks. Wireless Multimedia Sensor Networks(WMSNs have become the premier choice in many research communities and industry. Many state-of-art applications, such as surveillance, traffic monitoring, and remote heath care are essentially video tracking and transmission in WMSNs. The transmission speed is constrained by the big file size of video data and fixed bandwidth allocation in constant routing paths. In this paper, we present a CamShift based algorithm to compress the tracking of videos. Then we propose a bandwidth balancing strategy in which each sensor node is able to dynamically select the node for the next hop with the highest potential bandwidth capacity to resume communication. Key to this strategy is that each node merely maintains two parameters that contain its historical bandwidth varying trend and then predict its near future bandwidth capacity. Then, the forwarding node selects the next hop with the highest potential bandwidth capacity. Simulations demonstrate that our approach significantly increases the data received by the sink node and decreases the delay on video transmission in Wireless Multimedia Sensor Network environments.

  19. Thin film technologies for optoelectronic components in fiber optic communication

    Science.gov (United States)

    Perinati, Agostino

    1998-02-01

    will grow at an annual average rate of 22 percent from 1.3 million fiber-km in 1995 to 3.5 million fiber-km in 2000. The worldwide components market-cable, transceivers and connectors - 6.1 billion in 1994, is forecasted to grow and show a 19 percent combined annual growth rate through the year 2000 when is predicted to reach 17.38 billion. Fiber-in-the-loop and widespread use of switched digital services will dominate this scenario being the fiber the best medium for transmitting multimedia services. As long as communication will partially replace transportation, multimedia services will push forward technology for systems and related components not only for higher performances but for lower cost too in order to get the consumers wanting to buy the new services. In the long distance transmission area (trunk network) higher integration of electronic and optoelectronic functions are required for transmitter and receiver in order to allow for higher system speed, moving from 2.5 Gb/s to 5, 10, 40 Gb/s; narrow band wavelength division multiplexing (WDM) filters are required for higher transmission capacity through multiwavelength technique and for optical amplifier. In the access area (distribution network) passive components as splitters, couplers, filters are needed together with optical amplifiers and transceivers for point-to-multipoint optical signal distribution: main issue in this area is the total cost to be paid by the customer for basic and new services. Multimedia services evolution, through fiber to the home and to the desktop approach, will be mainly affected by the availability of technologies suitable for component consistent integration, high yield manufacturing processes and final low cost. In this paper some of the optoelectronic components and related thin film technologies expected to mainly affect the fiber optic transmission evolution, either for long distance telecommunication systems or for subscriber network, are presented.

  20. Chaos-Based Underwater Communication With Arbitrary Transducers and Bandwidth

    Directory of Open Access Journals (Sweden)

    Chao Bai

    2018-01-01

    Full Text Available In this work, an enhanced differential chaos shift keying (DCSK, based on a first order hybrid chaotic system, is being proposed for a high reliability underwater acoustic communication system. It can be integrated into systems that use standard existing transducers. We show that a coherent operation between the received signal and the time reversal of the basis function in a first order hybrid chaotic system maximizes the signal to noise ratio at the receiver. Concurrently, DCSK configuration is used to resist the distortion caused by the complex underwater acoustic channel. Our simulation results show that the proposed method has lower bit error rate (BER. In addition, it shows higher communication reliability over underwater acoustic channel as compared to the conventional DCSK using logistic map and its variant forms such as Correlation Delay Shift Keying (CDSK, Phase-Separate DCSK (PS-DCSK, High Efficiency DCSK (HE-DCSK, and Reference Modulated DCSK (RM-DCSK.

  1. Silicon dual-ring modulator driven by differential signal.

    Science.gov (United States)

    Yu, Hui; Pantouvaki, Marianna; Verheyen, Peter; Lepage, Guy; Absil, Philippe; Bogaerts, Wim; Van Campenhout, Joris

    2014-11-15

    A silicon dual-ring modulator consisting of two serially cascaded rings with embedded PN junctions is driven by a differential signal pair. We show by simulation and experiment that the device has advantages over the single-ring modulator in terms of optical bandwidth, 3-dB modulation bandwidth and bit rate, at the expense of a 1.7-dB increase in the transmission penalty and a twofold increase of the RF power consumption. Driven by differential pseudo random binary sequence (PRBS) signals of 0.5-V peak-to-peak voltage (Vpp), the dual-ring modulator exhibits optical bandwidths of 66 pm and 40 pm at 12.5  Gb/s and 20  Gb/s, respectively. In contrast, the single-ring modulator has an optical bandwidth of 26 pm under a single-end PRBS signal of 0.5  Vpp at 12.5  Gb/s, and its eye diagram closes if the bit rate rises to 20  Gb/s.

  2. Graphene oxide as a multi-functional p-dopant of transparent single-walled carbon nanotube films for optoelectronic devices

    Science.gov (United States)

    Han, Joong Tark; Kim, Jun Suk; Jo, Sae Byeok; Kim, Sung Hun; Kim, Jong Soo; Kang, Boseok; Jeong, Hee Jin; Jeong, Seung Yol; Lee, Geon-Woong; Cho, Kilwon

    2012-11-01

    Modulation of electronic structures and surface properties of transparent carbon nanotube films is a challenging issue for their application in optoelectronic devices. Here, we report, for the first time, that graphene oxide (GO) nanosheets play the role of a p-doping agent and surface energy modifier of single-walled carbon nanotube (SWCNT)-based transparent conducting electrodes (TCEs). The deposition of highly oxidized, small-sized (i.e., diameter of less than 500 nm) GO nanosheets onto a SWCNT network film reduces the sheet resistance of the pristine film to 60% of its original value by p-doping. The modified TCEs exhibit an outstanding optoelectronic feature of high conductivity with high transparency. Moreover, the wettability of the electrode surface was also noticeably increased, which is advantageous for the solution-based processing of organic electronics. Furthermore, the organic photovoltaic (OPV) cells with the GO-doped SWCNT anodes on flexible substrates were successfully demonstrated. In stark contrast to a power conversion efficiency of 0.44% for pristine SWCNT anodes, GO-doped SWCNT anodes show a drastically enhanced power conversion efficiency of 2.7%.Modulation of electronic structures and surface properties of transparent carbon nanotube films is a challenging issue for their application in optoelectronic devices. Here, we report, for the first time, that graphene oxide (GO) nanosheets play the role of a p-doping agent and surface energy modifier of single-walled carbon nanotube (SWCNT)-based transparent conducting electrodes (TCEs). The deposition of highly oxidized, small-sized (i.e., diameter of less than 500 nm) GO nanosheets onto a SWCNT network film reduces the sheet resistance of the pristine film to 60% of its original value by p-doping. The modified TCEs exhibit an outstanding optoelectronic feature of high conductivity with high transparency. Moreover, the wettability of the electrode surface was also noticeably increased, which is

  3. Design and development of cell queuing, processing, and scheduling modules for the iPOINT input-buffered ATM testbed

    Science.gov (United States)

    Duan, Haoran

    1997-12-01

    heuristic strategy that leads to 'socially optimal' solutions, yielding a maximum number of contention-free cells being scheduled. A novel mixed digital-analog circuit has been designed to implement the MUCS core functionality. The MUCS circuit maps the cell scheduling computation to the capacitor charging and discharging procedures that are conducted fully in parallel. The design has a uniform circuit structure, low interconnect counts, and low chip I/O counts. Using 2 μm CMOS technology, the design operates on a 100 MHz clock and finds a near-optimal solution within a linear processing time. The circuit has been verified at the transistor level by HSPICE simulation. During this research, a five-port IQ-based optoelectronic iPOINT ATM switch has been developed and demonstrated. It has been fully functional with an aggregate throughput of 800 Mb/s. The second-generation IQ-based switch is currently under development. Equipped with iiQueue modules and MUCS module, the new switch system will deliver a multi-gigabit aggregate throughput, eliminate HOL blocking, provide per-VC QoS, and achieve near-100% link bandwidth utilization. Complete documentation of input modules and trunk module for the existing testbed, and complete documentation of 3DQ, iiQueue, and MUCS for the second-generation testbed are given in this dissertation.

  4. Arrays of surface-normal electroabsorption modulators for the generation and signal processing of microwave photonics signals

    NARCIS (Netherlands)

    Noharet, Bertrand; Wang, Qin; Platt, Duncan; Junique, Stéphane; Marpaung, D.A.I.; Roeloffzen, C.G.H.

    2011-01-01

    The development of an array of 16 surface-normal electroabsorption modulators operating at 1550nm is presented. The modulator array is dedicated to the generation and processing of microwave photonics signals, targeting a modulation bandwidth in excess of 5GHz. The hybrid integration of the

  5. A stepped FM/CW lidar system using a dual parallel Mach-Zehnder modulator

    Science.gov (United States)

    Yang, Cheng-hua; Zhang, Yong; Shen, Zhi-qiang; Xu, Lu; Yang, Xu; Liu, Yue-hao; Jin, Chen-fei; Zhao, Yuan

    2017-11-01

    A stepped frequency-modulated continuous-wave lidar system using a dual parallel Mach-Zehnder modulator with heterodyne detection is demonstrated. The lidar transmitter utilizes a modulation loop circuit composed of an electro-optic dual parallel Mach-Zehnder modulator and a fiber amplifier, as well as a tunable Fabry-Perot filter to generate a bandwidth-enhanced stepped frequency-modulated signal. In addition, a centroid algorithm is used in the receiver to process the signal with both high precision and high accuracy. The simulation results demonstrated that the ranging precision of the proposed lidar was 2.09 cm and the ranging accuracy was 0.16 cm. A validation experiment verified that the data obtained in the simulation had a modulation bandwidth of 4 GHz using a 200-MHz signal source. The improvements resulted in a frequency-modulated continuous-wave lidar system with high precision and accuracy by operating a modulated signal with a wider modulation bandwidth using signal sources with low bandwidth in a low-cost and compact structure.

  6. Irradiation tests of optoelectronic components for LHC inner-detectors

    International Nuclear Information System (INIS)

    Dawson, I.; Oglesby, S.J.; Dowell, J.D.; Homer, R.J.; Kenyon, I.R.; Shaylor, H.R.; Wilson, J.A.

    1997-01-01

    Two kinds of optical-link technologies have been investigated for the readout of data at LHC experiments; one based on LEDs and the other on Multi-Quantum-Well modulators. Presented in this paper are the results of irradiating LEDs and MQW modulators with 1 MeV-equivalent neutrons and 24 GeV protons. The devices were biased and the performances of the optical links were monitored throughout the tests. The fluences achieved were ∝5 x 10 14 n cm -2 and ∝6 x 10 13 p cm -2 . (orig.)

  7. Ring modulator small-signal response analysis based on pole-zero representation.

    Science.gov (United States)

    Karimelahi, Samira; Sheikholeslami, Ali

    2016-04-04

    We present a closed-form expression for the small-signal response of a depletion-mode ring modulator and verify it by measurement results. Both electrical and optical behavior of micro-ring modulator as well as the loss variation due to the index modulation is considered in the derivation. This expression suggests that a ring modulator is a third-order system with one real pole, one zero and a pair of complex-conjugate poles. The exact positions of the poles/zero are given and shown to be dependent upon parameters such as electrical bandwidth, coupling condition, optical loss, and sign/value of laser detunings. We show that the location of zero is different for positive and negative detuning, and therefore, the ring modulator frequency response is asymmetric. We use the gain-bandwidth product as a figure of merit and calculate it for various pole/zero locations. We show that gain-bandwidth for the over-coupled ring modulator is superior compared to other coupling conditions. Also, we show that the gain-bandwidth product can be increased to a limit by increasing the electrical bandwidth.

  8. Density estimation and adaptive bandwidths: a primer for public health practitioners.

    Science.gov (United States)

    Carlos, Heather A; Shi, Xun; Sargent, James; Tanski, Susanne; Berke, Ethan M

    2010-07-23

    Geographic information systems have advanced the ability to both visualize and analyze point data. While point-based maps can be aggregated to differing areal units and examined at varying resolutions, two problems arise 1) the modifiable areal unit problem and 2) any corresponding data must be available both at the scale of analysis and in the same geographic units. Kernel density estimation (KDE) produces a smooth, continuous surface where each location in the study area is assigned a density value irrespective of arbitrary administrative boundaries. We review KDE, and introduce the technique of utilizing an adaptive bandwidth to address the underlying heterogeneous population distributions common in public health research. The density of occurrences should not be interpreted without knowledge of the underlying population distribution. When the effect of the background population is successfully accounted for, differences in point patterns in similar population areas are more discernible; it is generally these variations that are of most interest. A static bandwidth KDE does not distinguish the spatial extents of interesting areas, nor does it expose patterns above and beyond those due to geographic variations in the density of the underlying population. An adaptive bandwidth method uses background population data to calculate a kernel of varying size for each individual case. This limits the influence of a single case to a small spatial extent where the population density is high as the bandwidth is small. If the primary concern is distance, a static bandwidth is preferable because it may be better to define the "neighborhood" or exposure risk based on distance. If the primary concern is differences in exposure across the population, a bandwidth adapting to the population is preferred. Kernel density estimation is a useful way to consider exposure at any point within a spatial frame, irrespective of administrative boundaries. Utilization of an adaptive bandwidth

  9. An impact excitation system for repeatable, high-bandwidth modal testing of miniature structures

    Science.gov (United States)

    Bediz, Bekir; Korkmaz, Emrullah; Burak Ozdoganlar, O.

    2014-06-01

    Miniature components and devices are increasingly seen in a myriad of applications. In general, the dynamic behavior of miniature devices is critical to their functionality and performance. However, modal testing of miniature structures poses many challenges. This paper presents a design and evaluation of an impact excitation system (IES) for repeatable, high-bandwidth, controlled-force modal testing of miniature structures. Furthermore, a dynamic model of the system is derived and experimentally validated to enable the identification of the system parameters that yield single-hit impacts with desired bandwidth and force magnitude. The system includes a small instrumented impact tip attached to a custom designed flexure-based body, an automated electromagnetic release mechanism, and various precision positioners. The excitation bandwidth and the impact force magnitude can be controlled by selecting the system parameters. The dynamic model of the system includes the structural dynamics of the flexure-based body, the electromagnetic force and the associated eddy-current damping, and the impact event. A validation study showed an excellent match between the model simulations and experiments in terms of impact force and bandwidth. The model is then used to create process maps that relate the system parameters to the number of hits (single vs. multiple), the impact force magnitudes and the excitation bandwidths. These process maps can be used to select system parameters or predict system response for a given set of parameters. A set of experiments is conducted to compare the performances of the IES and a (manual) miniature impact hammer. It is concluded that the IES significantly improves repeatability in terms of the impact bandwidth, location, and force magnitude, while providing a high excitation-bandwidth and excellent coherence values. The application of the IES is demonstrated through modal testing of a miniature contact-probe system.

  10. Single cavity Fabry-Perot modulator enhancements and integrated vertically coupled cavity light-emitting diode

    Science.gov (United States)

    Liu, Daxin

    Fabry-Perot modulators with Multi-Quantum Wells (MQWs) cavities have been studied with great interest during recent years. Usually operating as intensity modulators, these devices have very high modulation contrast ratios, can be operated at very high speed, can be easily made into two dimensional arrays and can be integrated with silicon ICs. They are thus very promising for optical interconnects, optical switching and image processing applications. But before these modulators are to be used in real applications, there are several issues that need to be solved, including the parasitic phase modulation, the bandwidth of such modulators and the alignment of modulator operation wavelength with the wavelength of lasers or light emitting diodes. In this work, the phase properties of Fabry-Perot reflection modulators will be discussed first and an experimental method using a modified Michelson interferometer to characterize the exact phase change will be demonstrated. It is demonstrated that the phase of the reflection light beam from a Fabry-Perot modulator is determined not only by the refractive index change inside the cavity but also by the absorption change inside the cavity. With the purpose of expanding the limited bandwidth of such modulator, devices with short passive cavities are designed and fabricated, the results are described and trade-offs between modulation depth and bandwidth will be discussed. In order to solve the problem of alignment and expand the functionality of Fabry-Perot modulators further, vertically coupled cavity devices with each cavity being electrically controlled independently have been developed. Both a coupled cavity modulator and an integrated light emitting diode with a transmission Fabry-Perot modulator are demonstrated; the first device enhances the modulation bandwidth while the second device has the potential of combining the advantage of high speed operation of MQWs modulators with the long lifetime and low cost of light

  11. Increased Optoelectronic Quality and Uniformity of Hydrogenated p-InP Thin Films

    KAUST Repository

    Wang, Hsin-Ping

    2016-06-08

    The thin-film vapor-liquid-solid (TF-VLS) growth technique presents a promising route for high quality, scalable and cost-effective InP thin films for optoelectronic devices. Towards this goal, careful optimization of material properties and device performance is of utmost interest. Here, we show that exposure of polycrystalline Zn-doped TF-VLS InP to a hydrogen plasma (in the following referred to as hydrogenation) results in improved optoelectronic quality as well as lateral optoelectronic uniformity. A combination of low temperature photoluminescence and transient photocurrent spectroscopy were used to analyze the energy position and relative density of defect states before and after hydrogenation. Notably, hydrogenation reduces the intra-gap defect density by one order of magnitude. As a metric to monitor lateral optoelectronic uniformity of polycrystalline TF-VLS InP, photoluminescence and electron beam induced current mapping reveal homogenization of the grain versus grain boundary upon hydrogenation. At the device level, we measured more than 260 TF-VLS InP solar cells before and after hydrogenation to verify the improved optoelectronic properties. Hydrogenation increased the average open-circuit voltage (VOC) of individual TF-VLS InP solar cells by up to 130 mV, and reduced the variance in VOC for the analyzed devices.

  12. Characterization of Semiconductor Nanocrystal Assemblies as Components of Optoelectronic Devices

    Science.gov (United States)

    Malfavon-Ochoa, Mario

    dispersions of core and core/shell NCs will be shown to produce close packed assemblies of NCs forming near-wavelength luminescent superstructures separated in space. We show the dominant contribution of a two-monolayer thick sharp interface CdS shell to the diffraction efficiency, and necessarily the refractive index, of the NCs, independent of core size. Utilization of these gratings as in-coupling elements at various positions within a device architecture are also examined. These new observations were achieved by unprecedented control of NC architecture during dispersion processing, while maintaining high luminescence, made possible by optimized NC surface passivation. These studies enable the formation of new LED architectures, and new optoelectronic devices based on angle resolved, monochromatic fluorescence from diffraction gratings prepared from simple solution processing approaches. Further, the novel observation of angle amplified interfering fluorescence from these features is argued to be a result of long range radiative coupling and superradiance enabled by the monodispersity and high-quality NC surface passivation described herein.

  13. Nonlinear optical and optoelectronic studies of topological insulator surfaces

    Science.gov (United States)

    McIver, James W.

    Since their experimental discovery in 2008, topological insulators have been catapulted to the forefront of condensed matter physics research owing to their potential to realize both exciting new technologies as well as novel electronic phases that are inaccessible in any other material class. Their exotic properties arise from a rare quantum organization of its electrons called "topological order,'' which evades the conventional broken symmetry based-classification scheme used to categorize nearly every other state of ordered matter. Instead, topologically ordered phases are classified by topological invariants, which characterize the phase of an electron's wavefunction as it moves through momentum space. When a topologically ordered phase is interfaced with an ordinary phase, such as the vacuum, a novel metallic state appears at their shared boundary. In topological insulators, this results in the formation of a two-dimensional metallic state that spans all of its surfaces. The surface state electronic spectrum is characterized by a single linearly dispersing and helically spin-polarized Dirac cone that is robust against disorder. The helical nature of the surface Dirac cone is highly novel because the Dirac electrons carry a net magnetic moment and are capable of transporting 100% spin-polarized electrical currents, which are the long-sought electronic properties needed for many spin-based electronic applications. However, owing to the small bulk band gap and intrinsic electronic doping inherent to these materials, isolating the surface electronic response from the bulk has proven to be a major experimental obstacle. In this thesis, we demonstrate the means by which light can be used to isolate and study the surface electronic response of topological insulators using optoelectronic and nonlinear optical techniques. In chapter 1, we overview the physics of topological order and topological insulators. In chapter 2, we show how polarized light can be used to

  14. Computational design of surfaces, nanostructures and optoelectronic materials

    Science.gov (United States)

    Choudhary, Kamal

    Properties of engineering materials are generally influenced by defects such as point defects (vacancies, interstitials, substitutional defects), line defects (dislocations), planar defects (grain boundaries, free surfaces/nanostructures, interfaces, stacking faults) and volume defects (voids). Classical physics based molecular dynamics and quantum physics based density functional theory can be useful in designing materials with controlled defect properties. In this thesis, empirical potential based molecular dynamics was used to study the surface modification of polymers due to energetic polyatomic ion, thermodynamics and mechanics of metal-ceramic interfaces and nanostructures, while density functional theory was used to screen substituents in optoelectronic materials. Firstly, polyatomic ion-beams were deposited on polymer surfaces and the resulting chemical modifications of the surface were examined. In particular, S, SC and SH were deposited on amorphous polystyrene (PS), and C2H, CH3, and C3H5 were deposited on amorphous poly (methyl methacrylate) (PMMA) using molecular dynamics simulations with classical reactive empirical many-body (REBO) potentials. The objective of this work was to elucidate the mechanisms by which the polymer surface modification took place. The results of the work could be used in tailoring the incident energy and/or constituents of ion beam for obtaining a particular chemistry inside the polymer surface. Secondly, a new Al-O-N empirical potential was developed within the charge optimized many body (COMB) formalism. This potential was then used to examine the thermodynamic stability of interfaces and mechanical properties of nanostructures composed of aluminum, its oxide and its nitride. The potentials were tested for these materials based on surface energies, defect energies, bulk phase stability, the mechanical properties of the most stable bulk phase, its phonon properties as well as with a genetic algorithm based evolution theory of

  15. Broad bandwidth frequency domain instrument for quantitative tissue optical spectroscopy

    International Nuclear Information System (INIS)

    Pham, Tuan H.; Coquoz, Olivier; Fishkin, Joshua B.; Anderson, Eric; Tromberg, Bruce J.

    2000-01-01

    Near-infrared (NIR) optical properties of turbid media, e.g., tissue, can be accurately quantified noninvasively using methods based on diffuse reflectance or transmittance, such as frequency domain photon migration (FDPM). Factors which govern the accuracy and sensitivity of FDPM-measured optical properties include instrument performance, the light propagation model, and fitting algorithms used to calculate optical properties from measured data. In this article, we characterize instrument, model, and fitting uncertaintics of an FDPM system designed for clinical use and investigate how each of these factors affects the quantification of NIR absorption (μ a ) and reduced scattering (μ s ' ) parameters in tissue phantoms. The instrument is based on a 500 MHz, multiwavelength platform that sweeps through 201 discrete frequencies in as little as 675 ms. Phase and amplitude of intensity modulated light launched into tissue, i.e., diffuse photon density waves (PDW), are measured with an accuracy of ±0.30 degree sign and ±3.5%, while phase and amplitude precision are ±0.025 degree sign and ±0.20%, respectively. At this level of instrument uncertainty, simultaneous fitting of frequency-dependent phase and amplitude nonlinear model functions derived from a photon diffusion approximation provides an accurate and robust strategy for determining optical properties from FDPM data, especially for media with high absorption. In an optical property range that is characteristic of most human tissues in the NIR (5x10 -3 a -2 mm -1 , 0.5 s ' -1 ), we theoretically and experimentally demonstrate that the multifrequency, simultaneous-fit approach allows μ a and μ s ' to be quantified with an accuracy of ±5% and ±3%, respectively. Although exceptionally high levels of precision can be obtained using this approach ( a and μ s ' . (c) 2000 American Institute of Physics

  16. Maximum Bandwidth Enhancement of Current Mirror using Series-Resistor and Dynamic Body Bias Technique

    Directory of Open Access Journals (Sweden)

    V. Niranjan

    2014-09-01

    Full Text Available This paper introduces a new approach for enhancing the bandwidth of a low voltage CMOS current mirror. The proposed approach is based on utilizing body effect in a MOS transistor by connecting its gate and bulk terminals together for signal input. This results in boosting the effective transconductance of MOS transistor along with reduction of the threshold voltage. The proposed approach does not affect the DC gain of the current mirror. We demonstrate that the proposed approach features compatibility with widely used series-resistor technique for enhancing the current mirror bandwidth and both techniques have been employed simultaneously for maximum bandwidth enhancement. An important consequence of using both techniques simultaneously is the reduction of the series-resistor value for achieving the same bandwidth. This reduction in value is very attractive because a smaller resistor results in smaller chip area and less noise. PSpice simulation results using 180 nm CMOS technology from TSMC are included to prove the unique results. The proposed current mirror operates at 1Volt consuming only 102 µW and maximum bandwidth extension ratio of 1.85 has been obtained using the proposed approach. Simulation results are in good agreement with analytical predictions.

  17. A Wide-Bandwidth, Low-Noise SIS Receiver Design for Millimeter and Submillimeter Wavelengths

    Science.gov (United States)

    Sumner, Matthew; Blain, Andrew; Harris, Andrew; Hu, Robert; LeDuc, Henry G.; Miller, David; Rice, Frank; Weinreb, Sander; Zmuidzinas, Jonas

    2004-01-01

    In principle, millimeter and submillimeter heterodyne receivers using state-of-the-art SIS detectors are capable of extremely large instantaneous bandwidths with noise temperatures within a few Kelvin of the quantum limit. We are applying modem design tools, such as 3D electromagnetic simulators and Caltech's SuperMix SIS analysis package, to develop a new generation of waveguide SIS mixers with very broad RF and IF bandwidths. Our initial design consists of a double-sideband mixer targeted for the 180- 300 GHz band that uses a single SIS junction excited by a full bandwidth, fixed-tuned waveguide probe on a silicon substrate. The IF output band, limited by the MMIC low-noise IF preamplifier, is 6-18 GHz, providing an instantaneous RF bandwidth of 24 GHz (double-sideband). The SIS mixer conversion loss is predicted to be no more than 1-2 dB (single-sideband) with mixer noise temperatures across the band within 10 Kelvin of the quantum limit. The single-sideband receiver noise temperature goal is 70 Kelvin. The wide instantaneous bandwidth and low noise will result in an instrument capable of a variety of important astrophysical observations beyond the capabilities of current instruments. Lab testing of the receiver will begin in the summer of 2002, and a demonstration on the CSO should occur in the spring of 2003.

  18. Plasmonic finite-thickness metal-semiconductor-metal waveguide as ultra-compact modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Malureanu, Radu; Lavrinenko, Andrei

    2013-01-01

    We propose a plasmonic waveguide with semiconductor gain material for optoelectronic integrated circuits. We analyze properties of a finite-thickness metal-semiconductor-metal (F-MSM) waveguide to be utilized as an ultra-compact and fast plasmonic modulator. The InP-based semiconductor core allow...

  19. Finite-thickness metal-semiconductor-metal waveguide as plasmonic modulator

    DEFF Research Database (Denmark)

    Babicheva, Viktoriia; Malureanu, Radu; Lavrinenko, Andrei

    2012-01-01

    We analyze a finite-thickness metal-semiconductor-metal waveguide to be utilized as an ultra-compact plasmonic modulator in optoelectronic integrated circuits. The InP-based semiconductor core allows electrical control of signal propagation. We show that using thin metal layers instead of thick o...

  20. Combined Coding And Modulation Employing Multi Phase Shift ...

    African Journals Online (AJOL)

    In this paper a technique for combining Huffman code, array code and phase modulation is proposed with a view to reduce redundancy, provide error control and simultaneously optimise on channel bandwidth. The combined scheme provides a reduction in overall complexity of the communication system as compared to a ...