Spent fuel transportation cask response to a tunnel fire scenario

International Nuclear Information System (INIS)

Bajwa, C.S.; Adkins, H.E.; Cuta, J.M.

2004-01-01

On July 18, 2001, a freight train carrying hazardous (non-nuclear) materials derailed and caught fire while passing through the Howard Street railroad tunnel in downtown Baltimore, Maryland. The United States Nuclear Regulatory Commission (USNRC), one of the agencies responsible for ensuring the safe transportation of radioactive materials in the United States, undertook an investigation of the train derailment and fire to determine the possible regulatory implications of this particular event for the transportation of spent nuclear fuel by railroad. Shortly after the accident occurred, the USNRC met with the National Transportation Safety Board (NTSB), the U.S. agency responsible for determining the cause of transportation accidents, to discuss the details of the accident and the ensuing fire. Following these discussions, the USNRC assembled a team of experts from the National Institute of Standards and Technology (NIST), the Center for Nuclear Waste Regulatory Analyses (CNWRA), and Pacific Northwest National Laboratory (PNNL) to determine the thermal conditions that existed in the Howard Street tunnel fire and analyze the effects of this fire on various spent fuel transportation cask designs. The Fire Dynamics Simulator (FDS) code, developed by NIST, was used to determine the thermal environment present in the Howard Street tunnel during the fire. The FDS results were used as boundary conditions in the ANSYS registered and COBRA-SFS computer codes to evaluate the thermal performance of different cask designs. The staff concluded that the transportation casks analyzed would withstand a fire with thermal conditions similar to those that existed in the Baltimore tunnel fire event. No release of radioactive materials would result from exposure of the casks analyzed to such an event. This paper describes the methods and approach used for this assessment

The use of CAFE-3D for the simulation of tunnel fires

Energy Technology Data Exchange (ETDEWEB)

Lopez, C.; Koski, J.A.; Hohnstreiter, G.F.; Khalil, I. [Sandia National Labs., Albuquerque, NM (United States); Suo-Anttila, A. [Alion Science and Technology, Albuquerque, NM (United States)

2004-07-01

Fires after accidents inside tunnels, such as the July 2001 Howard Street Tunnel fire in Baltimore, Maryland, USA, have raised stakeholder questions concerning the survivability of a spent nuclear fuel (SNF) transport cask when exposed to similar thermal environments. The analysis of tunnel fires is a computational challenge because of the need for very large computational domains in order to fully simulate such a problem. In this paper, the analyses of two different tunnel fire scenarios are described and the performance of typical SNF casks when exposed to these tunnel fire environments is discussed. The CAFE-3D fire code is used to model a series of fires inside tunnels, and the thermal performance of a SNF transportation cask within such fire environments is estimated with the use of the MSC PATRAN-P/Thermal finite element analysis code. The methodology used to simulate this type of fire scenario as well as a description of the manner in which the CAFE code couples the computational fluid dynamics and the finite element analysis techniques are also presented.

The use of CAFE-3D for the simulation of tunnel fires

International Nuclear Information System (INIS)

Lopez, C.; Koski, J.A.; Hohnstreiter, G.F.; Khalil, I.; Suo-Anttila, A.

2004-01-01

Fires after accidents inside tunnels, such as the July 2001 Howard Street Tunnel fire in Baltimore, Maryland, USA, have raised stakeholder questions concerning the survivability of a spent nuclear fuel (SNF) transport cask when exposed to similar thermal environments. The analysis of tunnel fires is a computational challenge because of the need for very large computational domains in order to fully simulate such a problem. In this paper, the analyses of two different tunnel fire scenarios are described and the performance of typical SNF casks when exposed to these tunnel fire environments is discussed. The CAFE-3D fire code is used to model a series of fires inside tunnels, and the thermal performance of a SNF transportation cask within such fire environments is estimated with the use of the MSC PATRAN-P/Thermal finite element analysis code. The methodology used to simulate this type of fire scenario as well as a description of the manner in which the CAFE code couples the computational fluid dynamics and the finite element analysis techniques are also presented

The Rail Alignment Environmental Impact Statement: An Update

International Nuclear Information System (INIS)

Sweeney, R.

2005-01-01

On July 23,2002, the President of the United States signed into law a joint resolution of the United States Congress designating the Yucca Mountain site in Nye County, Nevada, for development as a geologic repository for the disposal of spent nuclear fuel and high-level radioactive waste. If the US. Nuclear Regulatory Commission authorizes construction of the repository and receipt and possession of spent nuclear fuel and high-level radioactive at Yucca Mountain, the U.S. Department of Energy (DOE) would be responsible for transporting these materials to the Yucca Mountain repository as part of its obligation under the Nuclear Waste Policy Act. Part of the site recommendation decision included the analysis of a nation-wide shipping campaign to the proposed repository site. The ''Final Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada'' (February 2002) (Repository EIS) evaluated the potential impacts of the transportation of 70,000 Metric Tons of Heavy Metal spent nuclear fuel and high-level radioactive waste from 77 locations around the nation to the potential repository in Nevada over a 24 year shipping campaign. In the Repository EIS, DOE identified mostly rail as its preferred mode of transportation, both nationally and in the State of Nevada. In December 2003, based on public comments and the environmental analyses in the Repository EIS, DOE identified a preference for the Caliente rail corridor in Nevada. On April 8, 2004, DOE issued a Record of Decision (ROD) on the Mode of Transportation and Nevada Rail Corridor for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain, Nye County, Nevada. In this ROD, the DOE announced that it had decided to select the mostly rail scenario analyzed in the Repository EIS as the transportation mode both on a national basis and in the State of Nevada. Under the mostly rail

A 2.5D finite element and boundary element model for the ground vibration from trains in tunnels and validation using measurement data

Science.gov (United States)

Jin, Qiyun; Thompson, David J.; Lurcock, Daniel E. J.; Toward, Martin G. R.; Ntotsios, Evangelos

2018-05-01

A numerical model is presented for the ground-borne vibration produced by trains running in tunnels. The model makes use of the assumption that the geometry and material properties are invariant in the axial direction. It is based on the so-called two-and-a-half dimensional (2.5D) coupled Finite Element and Boundary Element methodology, in which a two-dimensional cross-section is discretised into finite elements and boundary elements and the third dimension is represented by a Fourier transform over wavenumbers. The model is applied to a particular case of a metro line built with a cast-iron tunnel lining. An equivalent continuous model of the tunnel is developed to allow it to be readily implemented in the 2.5D framework. The tunnel structure and the track are modelled using solid and beam finite elements while the ground is modelled using boundary elements. The 2.5D track-tunnel-ground model is coupled with a train consisting of several vehicles, which are represented by multi-body models. The response caused by the passage of a train is calculated as the sum of the dynamic component, excited by the combined rail and wheel roughness, and the quasi-static component, induced by the constant moving axle loads. Field measurements have been carried out to provide experimental validation of the model. These include measurements of the vibration of the rail, the tunnel invert and the tunnel wall. In addition, simultaneous measurements were made on the ground surface above the tunnel. Rail roughness and track characterisation measurements were also made. The prediction results are compared with measured vibration obtained during train passages, with good agreement.

The Path to Baltimore's "Best Prospect" Jobs without a College Degree: Career Credentialing Programs at Baltimore's Community Colleges. The Abell Report. Volume 28, No. 2

Science.gov (United States)

Hopkins, Barbara L.

2015-01-01

Only one in five graduates of Baltimore City Public Schools matriculates to a four-year college; the vast majority enroll in community college or look for a full-time job. Baltimore graduates and job-seekers need postsecondary training that works. "The Path to Baltimore's 'Best Prospect' Jobs without a College Degree: Career Credentialing…

A symmetrical rail accelerator

International Nuclear Information System (INIS)

Igenbergs, E.

1991-01-01

This paper reports on the symmetrical rail accelerator that has four rails, which are arranged symmetrically around the bore. The opposite rails have the same polarity and the adjacent rails the opposite polarity. In this configuration the radial force acting upon the individual rails is significantly smaller than in a conventional 2-rail configuration and a plasma armature is focussed towards the axis of the barrel. Experimental results indicate a higher efficiency compared to a conventional rail accelerator

NAA of an iridium tracer to determine soot exposure of students commuting on Baltimore`s buses

Energy Technology Data Exchange (ETDEWEB)

Ondov, J.M.; Wu, C.C.; Lin, Zhibo; Kidwell, C.B. [Univ. of Maryland, College Park, MD (United States)

1997-12-01

Epidemiologic studies suggest that short-term increases in indices of particulate air pollution are associated with increased mortality and morbidity from respiratory and cardiovascular diseases. An important component of urban aerosol, diesel soot, is a known respiratory irritant and contains mutagenic and carcinogenic organic compounds. In the United States, motor vehicles are thought to be the largest single source of atmospheric soot and account for {approximately}36% of the annual anthropogenic emission of toxic polynuclear aromatic hydrocarbons (PAH). Much of the motor-vehicle-derived PAH originates from diesel-powered vehicles because their PAH emissions are up to 50-fold greater than those from gasoline engines. In Baltimore, city high school students take public buses to school and, often, must stand at bus stops while many diesel buses pass or stop before their own buses arrive. To estimate student exposures to soot emitted from public diesel buses (MTA) during commutes to city high schools, the Baltimore municipal fuel supply was tagged with an iridium tracer, and exposure was monitored during commutes with personal aerosol monitors as a part of the Baltimore Environmental Justice Project.

Rails on Windows

CERN Document Server

Hibbs, Curt

2007-01-01

It's no secret that the entire Ruby onRails core team uses OS X as their preferreddevelopment environment. Becauseof this, it is very easy to findauthoritative information on the webabout using Rails on OS X. But the truthis that Windows developers using Railsprobably outnumber those using otherplatforms. A Windows development environmentcan be just as productive asany other platform. This is a guide to developing with Rubyon Rails under Windows. It won't teachyou how to write Ruby on Rails web applications,but it will show you what toolsto use and how to set them up to createa complete Rail

Electrodynamic wear of rails in high current density rail gun discharges

International Nuclear Information System (INIS)

Edwards, W.T.; Caldwell, S.G.

1984-01-01

Significant advances in high current, high speed power sources, has in recent years allowed rail guns to produce very high velocity (> 10 km/sec) macroscopic particles (> 1/10 grams). A continuing problem is the structural integrity of the components under these loadings and in particular, the rail wear due to the high current density plasma contacts. In this investigation a small bore rail gun (6x5 mm) was used with a 10.6 kjoule capacitor energy source to examine the modes of rail damage. The rails were constructed of 110 copper base material. These rails were used in an uncoated condition and also with plasma sprayed coatings of W and W/WC. The resulting surface wear was characterized by standard metallurgical techniques and analyzed for the various coatings

Impact of the rail-pad multi-discrete model upon the prediction of the rail response

Science.gov (United States)

Mazilu, T.; Leu, M.

2017-08-01

Wheel/rail vibration has many technical effects such as wear of the rolling surfaces, rolling noise, settlement of the ballast and subgrade etc. This vibration is depending on the rail pad characteristic and subsequently, it is important to have an accurate overview on the relation between the rail pad characteristic and the level of the wheel/rail vibration. To this end, much theoretical and experimental research has been developed in the past, and for the theoretical approach the track model, in general, and, particularly, the rail pad model is of crucial importance. Usually, the rail pad model is discrete model one, neglecting the length of the rail pad. This fact is questionable because the sleepers span is only 4 times the rail pad length. Using the rail pad discrete model, the rail response is overestimated when the frequency of the excitation equals the pinned-pinned resonance frequency. In this paper, a multi-discrete model for the rail pad, consisting in many Kelvin-Voigt parallel systems, is inserted into an analytical model of the track. The track model is reduced to a rail taken as infinite Timoshenko beam, discretely supported via rail pad, sleeper and ballast. The influence of the number of Kelvin-Voigt systems of the rail pad model on the rail response is analysed.

Determination of the primary technical parameters of the test bench for controlling the temperature of rails and rail bars of continuous welded rail

Directory of Open Access Journals (Sweden)

Tertychnyi Vitalii

2017-01-01

Full Text Available One of the most important factors determining the reliability and safety of operation of the continuous welded rail track is the temperature of the rails. All conditions of laying, repair and maintenance of the track during the entire cycle of rails operation depend on it. The existing rail temperature monitoring method does not take into account a few significant factors and that leads to significant errors in determining the actual temperature of the rail bar. The authors propose a new rail temperature measurement method on a special test bench which maximally simulates possible environmental operating conditions for the rail bars, the profile of the roadway (embankment or cut, as well as the actual spatial latitude and meridian location of the rail slabs. At the bench, the studied rails are fastened with the help of rail braces on half ties, in the ballast bed, with sizes in accordance with the existing reference documents. At the first stage, the most common KB-65 intermediate fastener for the continuous welded rail in Ukraine will be used, while in subsequent stages KPP-5 fastening will be used.

Managing rail service life

Directory of Open Access Journals (Sweden)

Z. Popović

2014-10-01

Full Text Available The service life of rails depends especially on the operational loads and speeds on the railway lines, as well as on the rail maintenance policy. There are multiple aspects of rail maintenance optimization. The following article considers optimisation of rail maintenance activities relating to rail head surface condition in order to reduce corrective work on track geometry, as well as to minimize the overall costs for track maintenance. The objects of this research are issues and challenges related to rail and track maintenance in curves on modern conventional railway lines for mixed traffic.

Rail passengers rights

Directory of Open Access Journals (Sweden)

Đurđev Dušanka J.

2016-01-01

Full Text Available The legal framework of rail passengers rights is set out in a combination of international and European law: an international measure, the rather unwieldy Uniform Rules concerning the Contract for International Carriage of Passengers and Luggage by Rail, forming part of the Convention concerning International Carriage by Rail of 9 May 1980 (as amended by the Vilnius Protocol of 3 June 1999 ['CIV'], lays down a basic framework which is then fleshed out by more recent EU legislation, Regulation (EC No 1371/2007 on Rail Passengers ' Rights and Obligations. Regulation 1371/2007/EC on rail passenger rights and obligations sets out minimum quality standards that have to be guaranteed to all passengers on all lines. .

Some design aspects of a two-stage rail-to-rail CMOS op amp

NARCIS (Netherlands)

Gierkink, Sander L.J.; Holzmann, Peter J.; Wiegerink, Remco J.; Wassenaar, R.F.

1999-01-01

A two-stage low-voltage CMOS op amp with rail-to-rail input and output voltage ranges is presented. The circuit uses complementary differential input pairs to achieve the rail-to-rail common-mode input voltage range. The differential pairs operate in strong inversion, and the constant

Preliminary rail access study

International Nuclear Information System (INIS)

1990-01-01

The Yucca Mountain site, located on the southwestern edge of the Nevada Test Site, is an undeveloped area under investigation as a potential site for nuclear waste disposal by the US Department of Energy. The site currently lacks rail service and an existing rail right-of-way. If the site is suitable and selected for development as a disposal site, rail service is desirable to the Office of Civilian Radioactive Waste Management Program because of the potential of rail to reduce number of shipments and costs relative to highway transportation. This preliminary report is a summary of progress to date for activities to identify and evaluate potential rail options from major rail carriers in the region to the Yucca Mountain site. It is currently anticipated that the rail spur will be operational after the year 2000. 9 refs., 13 figs., 2 tabs

Aerodynamic Improvements to Cargo Carrying Rail Cars due to Roof Modifications

Science.gov (United States)

Condie, Robert; Maynes, Daniel

2012-11-01

The aerodynamic drag associated with the transport of commodities by rail is becoming increasingly important as the cost of diesel fuel increases. We provide an assessment of the influence of the roof structure on aerodynamic performance of two dissimilar rail cars, namely automobile carrying cars and coal carrying cars. Currently, the roof material for automobile carrying rail cars is corrugated steel, with the corrugation aligned perpendicular to the direction of travel. Coal cars are currently left uncovered for loading convenience and on the return leg from the power plant are empty. Aerodynamic drag data have been obtained through wind tunnel testing on 1/29 scale models to understand the savings that may be realized by judicious modification to the tops of both these car types. For the automobile-carrying cars, testing is performed for the corrugated and smooth roof configurations. This modification alone has the potential of reducing the car drag coefficient by nominally 25%. A broader study is performed for the coal cars, with data being acquired for coal filled models, empty models, and several cover prototype configurations. The results reveal that implementation of a cover may yield reductions in the aerodynamic drag for both coal filled (nominally 7%) and empty coal cars (nominally 30%).

Identification of the sources of PM10 in a subway tunnel using positive matrix factorization.

Science.gov (United States)

Park, Duckshin; Lee, Taejeong; Hwang, Doyeon; Jung, Wonseok; Lee, Yongil; Cho, KiChul; Kim, Dongsool; Lees, Kiyoung

2014-12-01

The level of particulate matter of less than 10 μm diameter (PM10) at subway platforms can be significantly reduced by installing a platform screen-door system. However, both workers and passengers might be exposed to higher PM10 levels while the cars are within the tunnel because it is a more confined environment. This study determined the PM10 levels in a subway tunnel, and identified the sources of PM10 using elemental analysis and receptor modeling. Forty-four PM10 samples were collected in the tunnel between the Gireum and Mia stations on Line 4 in metropolitan Seoul and analyzed using inductively coupled plasma-atomic emission spectrometry and ion chromatography. The major PM10 sources were identified using positive matrix factorization (PMF). The average PM10 concentration in the tunnels was 200.8 ± 22.0 μg/m3. Elemental analysis indicated that the PM10 consisted of 40.4% inorganic species, 9.1% anions, 4.9% cations, and 45.6% other materials. Iron was the most abundant element, with an average concentration of 72.5 ± 10.4 μg/m3. The PM10 sources characterized by PMF included rail, wheel, and brake wear (59.6%), soil combustion (17.0%), secondary aerosols (10.0%), electric cable wear (8.1%), and soil and road dust (5.4%). Internal sources comprising rail, wheel, brake, and electric cable wear made the greatest contribution to the PM10 (67.7%) in tunnel air. Implications: With installation of a platform screen door, PM10 levels in subway tunnels were higher than those on platforms. Tunnel PM10 levels exceeded 150 µg/m3 of the Korean standard for subway platform. Elemental analysis of PM10 in a tunnel showed that Fe was the most abundant element. Five PM10 sources in tunnel were identified by positive matrix factorization. Railroad-related sources contributed 68% of PM10 in the subway tunnel.

Implications of rail electrodynamics

International Nuclear Information System (INIS)

Rolader, G.E.; Jamison, K.A.

1990-01-01

A model is developed to investigate possible effects of rail electrodynamics on the performance of railguns. This model describes the oscillatory nature of the rail motion in response to the Lorentz force and the compressive restoration force of material which is behind the rails. In this simple model the rails are found to oscillate with a frequency of β. The rail dynamic behavior induces local electric fields. The authors investigate the significance of these electric fields on stationary particles (lab frame) and on particles moving at the velocity of the plasma/projectile system (projectile frame)

Mobile sources of polycyclic aromatic hydrocarbons (PAH) and nitro-PAH: Results of samples collected in a roadway tunnel

International Nuclear Information System (INIS)

Benner, B.A. Jr.; Gordon, G.E.; Wise, S.A.

1987-01-01

A recent review article emphasized the need for further characterizations of the carbonaceous fraction of mobile source emissions, particularly with the impending removal of lead alkyl octane boosters and bromine-containing lead scavengers from regular leaded gasolines. The lead and bromine emitted from the combustion of these fuels have been used as tracers of mobile source emissions for a number of years. Single vehicle emission studies have shed light on the relationship between engine operating parameters and the chemical characteristics of the emissions but they are not suitable for use in source apportionment studies which require emission data from a large number of different vehicles. Air particulate samples collected near a busy highway or in a roadway tunnel would be more appropriate for use in estimating the mobile source contribution of organic compounds to a region. Suspended particle samples collected in a heavily-travelled roadway tunnel (Baltimore Harbor Tunnel, Baltimore, Maryland) were characterized for polycyclic aromatic hydrocarbons (PAH) and some nitro-PAH by gas and liquid chromatographic techniques. These samples included those collected on Teflon filters and on glass fiber filters for investigating any differences in samples collected on an inert (Teflon) and more reactive (glass-fiber) medium. All samples collected on Teflon were backed-up with polyurethane foam plugs (PUF) which trapped any inherent vapor-phase PAH as well as any compounds ''blown-off'' the particles during collection

75 FR 76520 - Tennessee Southern Railroad Company, Patriot Rail, LLC, Patriot Rail Holdings LLC, and Patriot...

Science.gov (United States)

2010-12-08

... family by converting two of its subsidiaries from corporations into limited liability companies: (1... Railroad Company, Patriot Rail, LLC, Patriot Rail Holdings LLC, and Patriot Rail Corp.--Corporate Family... Railroad Company (TSRR), Patriot Rail, LLC (PRL) and its subsidiaries, Patriot Rail Holdings LLC (PRH) and...

Framing Light Rail Projects

DEFF Research Database (Denmark)

Olesen, Mette

2014-01-01

In Europe, there has been a strong political will to implement light rail. This article contributes to the knowledge concerning policies around light rail by analysing how local actors frame light rail projects and which rationalities and arguments are present in this decision-making process....... The article draws on the socio-technical approach to mobilities studies in order to reassemble the decision-making process in three European cases: Bergen, Angers, and Bern. This article provides insights into the political, discursive and material production of light rail mobilities in a European context....... It identifies the planning rationales behind the systems and the policies that have been supportive of this light rail vision. Finally, the article identifies the practical challenges and potentials that have been connected to the different local frames of light rail mobility which can be used in future...

Identification and prioritization of rail squat defects in the field using rail magnetisation technology

Science.gov (United States)

Kaewunruen, Sakdirat

2015-04-01

Inevitably, rail squats and studs are continuing to be a serious problem for railway organisations around the world in the 21st century. They are typically classified as the growth of any cracks that have grown longitudinally through the subsurface and some of the cracks propagating to the bottom of rails transversely, and have branched from initial longitudinal cracks with a depression of rail surface. The horizontal crack, which results in a depression of rail surface, induces increased maintenance level, more frequent monitoring, compromised rail testing (as the crack shields the signal echoes), and possible broken rails. This paper presents field investigations using a magnetised-rail testing device developed by MRX Technologies to identify and prioritise the rail squats. Most of the in situ squats were found on the high rail of the transition (variable-radius curved track), which is associated with rolling contact fatigue (RCF). This investigation highlights the field performance of the MRX's surface crack detection technology in comparison with the traditional ultrasonic method and detailed walking inspection. Visually, it was found in the field that the size of the RCF squats varies from very small to moderate. The predicted crack data were obtained by scanning the magnitised rails. The comparison of the actual crack depths (ultrasonic) and the predicted crack depths (MRX device) shows: • A possible correlation for small RCF/ squat cracks. • Poor interpretation of larger defects and welds. The field assessment also suggests some practical issues required for further development, including the detection of rail spalling, deep transverse crack, welding, and so on.

Possible Concepts for Waterproofing of Norwegian TBM Railway Tunnels

Science.gov (United States)

Dammyr, Øyvind; Nilsen, Bjørn; Thuro, Kurosch; Grøndal, Jørn

2014-05-01

The aim of this paper is to evaluate and compare the durability, life expectancy and maintenance needs of traditional Norwegian waterproofing concepts to the generally more rigid waterproofing concepts seen in other European countries. The focus will be on solutions for future Norwegian tunnel boring machine railway tunnels. Experiences from operation of newer and older tunnels with different waterproofing concepts have been gathered and analyzed. In the light of functional requirements for Norwegian rail tunnels, some preliminary conclusions about suitable concepts are drawn. Norwegian concepts such as polyethylene panels and lightweight concrete segments with membrane are ruled out. European concepts involving double shell draining systems (inner shell of cast concrete with membrane) and single shell undrained systems (waterproof concrete segments) are generally evaluated as favorable. Sprayable membranes and waterproof/insulating shotcrete are welcomed innovations, but more research is needed to verify their reliability and cost effectiveness compared to the typical European concepts. Increasing traffic and reliance on public transport systems in Norway result in high demand for durable and cost effective solutions.

Bronze railing from Mediana

Directory of Open Access Journals (Sweden)

Vasić Miloje R.

2003-01-01

Full Text Available The hoard containing components of bronze railing was discovered in trench 7 during excavations at Mediana in 2000. Railing consists of cancelli and herms with busts of deities between them. Railing was constructed in such a way that it was possible to disassemble and reassemble it. Three cancelli one fragmented semicancellus cast together with herm and herms, one with bust of Aesculapius and other with bust of Luna. It could be concluded that railing consisted of two segments with passage between them. Male deities were represented on the left segment of the railing and female deities on the right segment. Detailed analysis revealed that Aesculapius as well as Luna bear strong mark of classical Greek and Hellenistic art, which experienced some kind of renaissance in the time of Constantine I. It is very probable that we can recognize the portrait of Faustina, Constantine’s wife in the portrait of Luna. According to the historical events the railing could have been produced before 325 AD when Constantine definitively accepted Christianity at Council of Nicaea. It is difficult to say where the railing had been produced. It had been most probably brought to Mediana during the stay of emperor Julian in Niš in 361. The sculptures found in one room of the villa with peristyle had probably been brought at the same time. The apse of triclinium of this villa had most likely been arranged as small shrine with bronze railing at its entrance. The railing was buried in 378 after battle of Adrianople and invasion of Goths in diocese Dacia.

Watersheds in Baltimore, Maryland: understanding and application of integrated ecological and social processes

Science.gov (United States)

Steward T.A. Pickett; Kenneth T. Belt; Michael F. Galvin; Peter M. Groffman; J. Morgan Grove; Donald C. Outen; Richard V. Pouyat; William P. Stack; Mary L. Cadenasso

2007-01-01

The Water and Watersheds program has made significant and lasting contributions to the basic understanding of the complex ecological system of Baltimore, MD. Funded at roughly the same time as the urban Long- Term Ecological Research (LTER) project in Baltimore, the Water and Watersheds grant and the LTER grant together established the Baltimore Ecosystem Study (BES)...

A low-voltage Op Amp with rail-to-rail constant-gm input stage and a class AB rail-to-rail output stage

NARCIS (Netherlands)

Botma, J.H.; Wassenaar, R.F.; Wiegerink, Remco J.

1993-01-01

In this paper a low-voltage two-stage Op Amp is presented. The Op Amp features rail-to-rail operation and has an @put stage with a constant transconductance (%) over the entire common-mode input range. The input stage consists of an n- and a PMOS differential pair connected in parallel. The constant

Rail vehicle dynamics

CERN Document Server

Knothe, Klaus

2017-01-01

This book on the dynamics of rail vehicles is developed from the manuscripts for a class with the same name at TU Berlin. It is directed mainly to master students with pre-knowledge in mathematics and mechanics and engineers that want to learn more. The important phenomena of the running behaviour of rail vehicles are derived and explained. Also recent research results and experience from the operation of rail vehicles are included. One focus is the description of the complex wheel-rail contact phenomena that are essential to understand the concept of running stability and curving. A reader should in the end be able to understand the background of simulation tools that are used by the railway industry and universities today.

Návrh Rail-to-Rail proudového konvejoru v technologii CMOS

OpenAIRE

Hudzik, Martin

2016-01-01

Diplomová práca sa zaoberá návrhom rail-to-rail prúdového konvejora druhej generácie v technológii CMOS. Opisuje princípy funkcie jednotlivých generácii prúdových konvejorov a taktiež základný princíp návrhu prúdového konvejora druhej generácie založeného na operačnom zosilňovači. Venuje sa obvodovému riešeniu vstupného rail-to-rail stupňa a koncového stupňa v triede AB. Cieľom tejto práce je navrhnúť, charakterizovať vlastnosti a vytvoriť topológiu prúdového konvejora druhej generácie s rail...

Design of Low Voltage Low Power CMOS OP-AMPS with Rail-to-Rail Input/Output Swing

OpenAIRE

Gopalaiah, SV; Shivaprasad, AP; Panigrahi, Sukanta K

2004-01-01

A novel input and output biasing circuit to extend the input common mode (CM) voltage range and the output swing to rail-to-rail in a low voltage op-amp in standard CMOS technology is presented. The input biasing circuit uses a Switched Capacitor Based Attenuator (SCBA) approach to establish rail-to-rail common mode input voltage range. And the output biasing circuit uses an Output Driver (OD), with floating bias to give the rail-to-rail swing at output stage. Three different OD schemes in op...

40 CFR 81.28 - Metropolitan Baltimore Intrastate Air Quality Control Region.

Science.gov (United States)

2010-07-01

... Quality Control Region. 81.28 Section 81.28 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY... Air Quality Control Regions § 81.28 Metropolitan Baltimore Intrastate Air Quality Control Region. The Metropolitan Baltimore Intrastate Air Quality Control Region (Maryland) consists of the territorial area...

High speed rails. Fatigue behaviour

International Nuclear Information System (INIS)

Duart, J. M.; Pero-Sanz, J. A.; Verdeja, J. I.

2005-01-01

In recent years, passenger train speed and freight train load have increased to enhance efficiency of rail road transportation. These trends have increased the severity of rail service conditions, calling for rails with greater wear resistance, strength and fatigue behaviour. In the United Stated and Europe, track site weld rails are made entirely by aluminothermic process. This work describes the results of experimental study conducted on bending fatigue strength of plain rails and aluminothermic welded rails with preheating procedures (oxipropane and air-induced propane) approved by railways authorities. Compliance with the required fatigue strength shall be ascertained by 4 point pulsating bending test in accordance with European standards by aluminothermic welding in rails. The locati method, based in the empirical Miner's law about the cumulative damage on a fatigue tested material, allows, once known the Wohler curve of the welding process in use to settle the fatigue tensile limit at 50% with only one test. The values obtained at 2.10''6 cycles for plain rails (S f =353 MPa), oxipropane preheated aluminothermic weld rails (S f =225 MPa), and propane-air induced aluminothermic weld rails (S f =210 MPa) are very similar to those resulting from test method stated in the European Standard. From our point of view and due to its ease, speediness and savings, this is the most suitable test to check the quality and compare the aluminothermic processes in use. (Author) 15 refs

Background Pressure Profiles for Sonic Boom Vehicle Testing in the NASA Glenn 8- by 6-Foot Supersonic Wind Tunnel

Science.gov (United States)

Castner, Raymond; Shaw, Stephen; Adamson, Eric; Simerly, Stephanie

2013-01-01

In an effort to identify test facilities that offer sonic boom measurement capabilities, an exploratory test program was initiated using wind tunnels at NASA research centers. The subject of this report is the sonic boom pressure rail data collected in the Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel. The purpose is to summarize the lessons learned based on the test activity, specifically relating to collecting sonic boom data which has a large amount of spatial pressure variation. The wind tunnel background pressure profiles are presented as well as data which demonstrated how both wind tunnel Mach number and model support-strut position affected the wind tunnel background pressure profile. Techniques were developed to mitigate these effects and are presented.

Simply rails 2 the ultimate beginner's guide to Ruby on rails

CERN Document Server

Lenz, Patrick

2008-01-01

Want to learn all about Ruby on Rails 2.0, the web application framework that is inspiring developers around the world? The second edition of this practical, hands on book will: show you how to install Ruby on Rails on Windows, Mac, or Linux walk you, step by step, through the development of a Web 2.0 social news application, just like digg.com show you how to test, debug, benchmark, and deploy your Rails application Unlike other Rails books, this book doesn't assume that you are an experienced web developer, or that you've used Ruby before. An entire chapter is devoted to learning Ruby in a fun way, using the interactive Ruby console, so you can follow along at home. You'll be an accomplished Ruby programmer in no time! The example application that the book builds - a user-generated news web site - is built upon with each following chapter, and concepts such as sessions, cookies and basic AJAX usage are gradually introduced. Different aspects of Rails, such as user authentication, session cookies, and automa...

The Baltimore Engineers and the Chesapeake Bay, 1961-1987

Science.gov (United States)

1988-01-01

Army Engineer Waterways Experiment Station: David F. Bastian and Norman W. Scheffner. At the University of Maryland Baltimore County: Howard E...Howard, Smallwood and Armisted. By the time of the Civil War, Baltimore was one of the best defended ports in the world. The forts at Hampton Roads and...Marine Sciences. The salinity and current velocity data were collected at 199 and 205 stations respectively. Norman Scheffner of WES de- veloped a

Optimization of wheel-rail interface friction using top-of-rail friction modifiers: State of the art

Science.gov (United States)

Khan, M. Roshan; Dasaka, Satyanarayana Murty

2018-05-01

High Speed Railways and Dedicated Freight Corridors are the need of the day for fast and efficient transportation of the ever growing population and freight across long distances of travel. With the increase in speeds and axle loads carried by these trains, wearing out of rails and train wheel sections are a common issue, which is due to the increase in friction at the wheel-rail interfaces. For the cases where the wheel-rail interface friction is less than optimum, as in case of high speed trains with very low axle loads, wheel-slips are imminent and loss of traction occurs when the trains accelerate rapidly or brake all of a sudden. These vast variety of traction problems around the wheel-rail interface friction need to be mitigated carefully, so that the contact interface friction neither ascents too high to cause material wear and need for added locomotive power, nor be on the lower side to cause wheel-slips and loss of traction at high speeds. Top-of-rail friction modifiers are engineered surface coatings applied on top of rails, to maintain an optimum frictional contact between the train wheels and the rails. Extensive research works in the area of wheel-rail tribology have revealed that the optimum frictional coefficients at wheel-rail interfaces lie at a value of around 0.35. Application of top-of-rail (TOR) friction modifiers on rail surfaces add an extra layer of material coating on top of the rails, with a surface frictional coefficient of the desired range. This study reviews the common types of rail friction modifiers, the methods for their application, issues related with the application of friction modifiers, and a guideline on selection of the right class of coating material based on site specific requirements of the railway networks.

Head first rails a learner's companion to ruby on rails

CERN Document Server

Griffiths, David

2009-01-01

Ready to transport your web applications into the Web 2.0 era? Head First Rails takes your programming -- and productivity -- to the max. You'll learn everything from the fundamentals of Rails scaffolding to building customized interactive web apps using Rails' rich set of tools and the MVC framework. By the time you're finished, you'll have learned more than just another web framework. You'll master database interactions, integration with Ajax and XML, rich content, and even dynamic graphing of your data -- all in a fraction of the time it takes to build the same apps with Java, PHP, ASP.NE

Scheduling freight trains in rail-rail transshipment yards

OpenAIRE

Nils Boysen; Erwin Pesch

2008-01-01

Transshipment yards, where gantry cranes allow for an effcient transshipment of containers between different freight trains, are important entities in modern railway systems and facilitate the general shift from point-to-point transport to hub-and-spoke railway systems. Modern rail-rail transshipment yards accelerate container handling, so that multiple smaller trains with equal destination can be consolidated to a reduced number of trains without jeopardizing on time deliveries. An important...

75 FR 24774 - Fairmount Bank, Baltimore, MD; Approval of Conversion Application

Science.gov (United States)

2010-05-05

... DEPARTMENT OF THE TREASURY Office of Thrift Supervision [AC-36 OTS Nos. 08193 and H4677] Fairmount Bank, Baltimore, MD; Approval of Conversion Application Notice is hereby given that on April 15, 2010, the Office of Thrift Supervision approved the application of Fairmount Bank, Baltimore, Maryland, to...

Rail inspection of RCF defects

Directory of Open Access Journals (Sweden)

Z. Popović

2013-10-01

Full Text Available Rail defects due to rolling contact fatigue (RCF threaten the traffic safety around the world. That hazard is more distinct on railways without adequate maintenance strategy. Realization of interoperability of European railway network demands from every infrastructure manager to have a maintenance plan for the infrastructure subsystem. Besides that, this plan includes rail inspection and strategy against RCF defects. This paper emphasizes the importance of rail inspection and early detection of RCF because the most of RCF crack should be removed in rail grinding campaigns (preventive, cyclical and corrective activities during the whole rail service life.

Light rail project in Copenhagen

DEFF Research Database (Denmark)

Andersen, Jonas Lohmann Elkjær; Landex, Alex; Nielsen, Otto Anker

2006-01-01

The need for high class public transport service of the increasing travel across the radial urban structure of the greater Copenhagen region was examined through planning of a light rail. The exact corridor (defined as the Ring 2½ corridor) and alignment of the light rail were documented and the ......The need for high class public transport service of the increasing travel across the radial urban structure of the greater Copenhagen region was examined through planning of a light rail. The exact corridor (defined as the Ring 2½ corridor) and alignment of the light rail were documented...... light rail projects...

A survey of wheel-rail contact models for rail vehicles

Science.gov (United States)

Meymand, Sajjad Z.; Keylin, Alexander; Ahmadian, Mehdi

2016-03-01

Accurate and efficient contact models for wheel-rail interaction are essential for the study of the dynamic behaviour of a railway vehicle. Assessment of the contact forces and moments, as well as contact geometry provide a fundamental foundation for such tasks as design of braking and traction control systems, prediction of wheel and rail wear, and evaluation of ride safety and comfort. This paper discusses the evolution and the current state of the theories for solving the wheel-rail contact problem for rolling stock. The well-known theories for modelling both normal contact (Hertzian and non-Hertzian) and tangential contact (Kalker's linear theory, FASTSIM, CONTACT, Polach's theory, etc.) are reviewed. The paper discusses the simplifying assumptions for developing these models and compares their functionality. The experimental studies for evaluation of contact models are also reviewed. This paper concludes with discussing open areas in contact mechanics that require further research for developing better models to represent the wheel-rail interaction.

75 FR 55631 - U. S. Rail Corporation-Construction and Operation Exemption-Brookhaven Rail Terminal

Science.gov (United States)

2010-09-13

... the proposed construction is to enable U. S. Rail to serve the BRT as a common carrier and to deliver... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35141] U. S. Rail Corporation--Construction and Operation Exemption-- Brookhaven Rail Terminal AGENCY: Surface Transportation...

Performance criteria for EM rail launchers with solid or transition armatures and laminated rails

International Nuclear Information System (INIS)

James, T.E.

1991-01-01

Velocity limitations of EM Rail Launchers with solid armatures due to the velocity skin-effect are assessed for a range of homogeneous materials (copper, aluminium, molybdenum and tungsten). Performance criteria as limited by armature melting in the region adjacent to the rail/armature contact surface and by rail surface melting are deduced analytically based on defined electro-thermal reference conditions. The performance criteria predict the reference transition velocity at which the solid contact surface changes to mainly a melted contact surface which is shown to be a fundamental property of the materials. The paper shows that the critical factors in obtaining a high transition velocity are a relatively high resistivity armature material combined with high temperature rail surface coatings. For example a transition velocity of >2.0 km/s for a molybdenum armature and a tungsten rail surface coating on a copper rail are predicted compared with <0.5 km/s for the aluminium/copper combination frequently used

Rail-induced Traffic in China

Directory of Open Access Journals (Sweden)

Nan He

2017-11-01

Full Text Available The rapid development of China’s railway has exerted an enormous influence on the intercity passenger transport structure in recent years. However, it has not satisfied the passengers’ travel demand due to induced traffic. This paper is committed to solving such issue, with the aim of satisfying the current travel demand, and of anticipating the demand of the predicted traffic growth over the next 20 to 30 years. The paper has considered the increase in rail passenger kilometres caused by the growth of rail kilometres as rail-induced traffic. Based on the concept and former research of induced traffic, the panel data of 26 provinces and 3 municipalities of China between the year 2000 and 2014 were collected, and the elasticity models (including elasticity-based model, distributed lag model, high-speed rail (HSR elasticity model and rail efficiency model have been constructed. The results show the importance of model formation incorporation of rail-induced traffic. It is better to get the correct value in divided zones with different train frequencies or incorporation rail efficiency in cities or provinces. The lag time and rail types also need to be considered. In summary, the results analysis not only confirms the existence of rail-induced traffic, but also provides substantial recommendations to train operation planning.

46 CFR 169.329 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Storm rails. 169.329 Section 169.329 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) NAUTICAL SCHOOLS SAILING SCHOOL VESSELS Construction and Arrangement Rails and Guards § 169.329 Storm rails. Suitable storm rails or hand grabs must be...

46 CFR 177.920 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Storm rails. 177.920 Section 177.920 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS (UNDER 100 GROSS TONS) CONSTRUCTION AND ARRANGEMENT Rails and Guards § 177.920 Storm rails. Suitable storm rails or hand grabs must be...

46 CFR 127.320 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 127.320 Section 127.320 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) OFFSHORE SUPPLY VESSELS CONSTRUCTION AND ARRANGEMENTS Rails and Guards § 127.320 Storm rails. Suitable storm rails must be installed in each passageway and at...

Rail abandonments in the South and their effect on NWPA rail shipments

International Nuclear Information System (INIS)

1988-02-01

The railroad industry will have a very critical role in the eventual shipping of commercial spent fuel and defense high-level waste as provided under the Nuclear Waste Policy Act of 1982 and the 1987 amendments. The transport of spent fuel is expected to be accomplished by rail from 19 of the South's 27 reactor sites to the proposed Yucca Mountain repository or possible monitored retrievable storage facility. The decline in total track availability, however, could significantly impact the federal government's transportation program. Particularly the situation of continuing abandonments may limit rail opportunities at numerous reactor locations. Commercial nuclear reactor sites have the unfortunate problem of not being located on Class I railroad mainline tracks. The reactor sites are generally located in areas with limited rail traffic and thus vulnerable to rail abandonment procedures. The general deregulation of the railroad industry under the Staggers Act of 1980 also assisted in making rail abandonment, through the Interstate Commerce Commission, a rather simple and quick process. The effects of deregulation, however, have provided alternatives to abandonment. In particular, the Staggers Act has led to an enormous surge in the growth of short line and regional railroads. Such railroads have been able to effectively operate rail lines which Class I railroads found unprofitable. The short lines and regionals were also encouraged to competitively negotiate contracts directly with shippers. While these railroads may help reduce the number of abandonment applications, they may also represent higher shipping costs. The South has experienced a great number of abandonments since the 1960's. Many of the abandonments have been significant in length and have affected areas near nuclear plants expected to ship by rail

78 FR 10581 - Rail Vehicles Access Advisory Committee

Science.gov (United States)

2013-02-14

... guideway systems (e.g., rapid rail, light rail, commuter rail, and intercity rail). We are establishing a... vehicles that operate on fixed guideway systems (e.g., rapid rail, light rail, commuter rail, and intercity... for their service. We may pay travel expenses for a limited number of persons who would otherwise be...

46 CFR 108.221 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 108.221 Section 108.221 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) A-MOBILE OFFSHORE DRILLING UNITS DESIGN AND EQUIPMENT Construction and Arrangement Rails § 108.221 Storm rails. Each unit must have a storm rail in the following...

78 FR 73438 - Reorganization of Sector Baltimore and Hampton Roads; Conforming Amendments

Science.gov (United States)

2013-12-06

...-0251] RIN 1625-ZA32 Reorganization of Sector Baltimore and Hampton Roads; Conforming Amendments AGENCY... Roads' Marine Inspection Zone and Captain of the Port Zones. These conforming amendments are necessary... lines separating Sector Baltimore and Sector Hampton Roads. See Operating Facility Change Order (OFCO...

49 CFR 214.523 - Hi-rail vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Hi-rail vehicles. 214.523 Section 214.523..., DEPARTMENT OF TRANSPORTATION RAILROAD WORKPLACE SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.523 Hi-rail vehicles. (a) The hi-rail gear of all hi-rail vehicles shall be inspected for...

Rail-to-rail low-power fully differential OTA utilizing adaptive biasing and partial feedback

DEFF Research Database (Denmark)

Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

A fully differential rail-to-rail Operational Transconductance Amplifier (OTA) with improved DC-gain and reduced power consumption is proposed in this paper. By using the adaptive biasing circuit and two differential inputs, a low stand-by current can be obtained together with reduced power...... consumption. The DC-gain of the proposed OTA is improved by adding a partial feedback loop. A Common-Mode Feedback (CMFB) circuit is required for fully differential rail-to-rail operation. Simulations show that the OTA topology has a low stand-by power consumption of 96μW and a high FoM of 3.84 [(V...

THE BAINITIC STEELS FOR RAILS APPLICATIONS

Directory of Open Access Journals (Sweden)

Ivo Hlavatý

2009-10-01

Full Text Available Actual trends of worldwide railway transport development are characterized by increasing speed and growth of railway’s axels load. Increasing load together with transverse, longitudinal wheel displacement and braking on the rails results into heavy surface tension. One of many applications for bainitic steel is in railway transport for highly strength and wear resistant rails. Rail steel must be designed to be able to resist plastic deformation, wear, rolling contact fatigue, bending stress and thermal stress during rail welding process and rails resurfacing.

Visualizing and Understanding Socio-Environmental Dynamics in Baltimore

Science.gov (United States)

Zaitchik, B. F.; Omeara, K.; Guikema, S.; Scott, A.; Bessho, A.; Logan, T. M.

2015-12-01

The City of Baltimore, like any city, is the sum of its component neighborhoods, institutions, businesses, cultures, and, ultimately, its people. It is also an organism in its own right, with distinct geography, history, infrastructure, and environments that shape its residents even as it is shaped by them. Sometimes these interactions are obvious but often they are not; while basic economic patterns are widely documented, the distribution of socio-spatial and environmental connections often hides below the surface, as does the potential that those connections hold. Here we present results of a collaborative initiative on the geography, design, and policy of socio-environmental dynamics of Baltimore. Geospatial data derived from satellite imagery, demographic databases, social media feeds, infrastructure plans, and in situ environmental networks, among other sources, are applied to generate an interactive portrait of Baltimore City's social, health, and well-being dynamics. The layering of data serves as a platform for visualizing the interconnectedness of the City and as a database for modeling risk interactions, vulnerabilities, and strengths within and between communities. This presentation will provide an overview of project findings and highlight linkages to education and policy.

Determination of rail wear and short-time wear measurements of rails applying radioisotopes

International Nuclear Information System (INIS)

Grohmann, H.D.

1981-01-01

An energetic model has been developed for calculating rail wear. Short-time wear tests on rails after surface activation and following activity measurements showed a good agreement with the calculated values

Fast rail corrugation detection based on texture filtering

Science.gov (United States)

Xiao, Jie; Lu, Kaixia

2018-02-01

The condition detection of rails in high-speed railway is one of the important means to ensure the safety of railway transportation. In order to replace the traditional manual inspection, save manpower and material resources, and improve the detection speed and accuracy, it is of great significance to develop a machine vision system for locating and identifying defects on rails automatically. Rail defects exhibit different properties and are divided into various categories related to the type and position of flaws on the rail. Several kinds of interrelated factors cause rail defects such as type of rail, construction conditions, and speed and/or frequency of trains using the rail. Rail corrugation is a particular kind of defects that produce an undulatory deformation on the rail heads. In high speed train, the corrugation induces harmful vibrations on wheels and its components and reduces the lifetime of rails. This type of defects should be detected to avoid rail fractures. In this paper, a novel method for fast rail corrugation detection based on texture filtering was proposed.

Active current management for four-rail railguns

International Nuclear Information System (INIS)

Beno, J.H.; Weldon, W.F.

1991-01-01

In this paper a system of auxiliary conductors designed to reduce current density peaks in railgun rails for four-rail, round-bore railguns is described. The effects on rail current density and projectile force are discussed. Railgun cross-sectional designs are presented for round-bore, four-rail railguns which operate at lower peak current densities and develop greater projectile forces than conventional two-rail, round-bore railguns

Rail projects gather steam

Energy Technology Data Exchange (ETDEWEB)

NONE

2010-01-15

The global recession hit rail companies hard, as demand for bulk commodities such as coal was affected. But green shoots of recovery are now appearing, with many rail companies announcing new haulage contracts. 3 figs.

Rail Access to Yucca Mountain: Critical Issues

International Nuclear Information System (INIS)

Halstead, R. J.; Dilger, F.; Moore, R. C.

2003-01-01

The proposed Yucca Mountain repository site currently lacks rail access. The nearest mainline railroad is almost 100 miles away. Absence of rail access could result in many thousands of truck shipments of spent nuclear fuel and high-level radioactive waste. Direct rail access to the repository could significantly reduce the number of truck shipments and total shipments. The U.S. Department of Energy (DOE) identified five potential rail access corridors, ranging in length from 98 miles to 323 miles, in the Final Environmental Impact Statement (FEIS) for Yucca Mountain. The FEIS also considers an alternative to rail spur construction, heavy-haul truck (HHT) delivery of rail casks from one of three potential intermodal transfer stations. The authors examine the feasibility and cost of the five rail corridors, and DOE's alternative proposal for HHT transport. The authors also address the potential for rail shipments through the Las Vegas metropolitan area

Rail base corrosion and cracking prevention

Science.gov (United States)

2014-07-01

Rail base corrosion combined with fatigue or damage can significantly reduce rail life. Studies were done to examine the relative contribution of damage, corrosion, and fatigue on rail life. The combined effects can be separated into constituent fact...

49 CFR 210.9 - Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 4 2010-10-01 2010-10-01 false Movement of a noise defective locomotive, rail car, or consist of a locomotive and rail cars. 210.9 Section 210.9 Transportation Other Regulations... locomotive, rail car, or consist of a locomotive and rail cars. A locomotive, rail car, or consist of a...

Baltimore District Tackles High Suspension Rates

Science.gov (United States)

Maxwell, Lesli A.

2007-01-01

This article reports on how the Baltimore District tackles its high suspension rates. Driven by an increasing belief that zero-tolerance disciplinary policies are ineffective, more educators are embracing strategies that do not exclude misbehaving students from school for offenses such as insubordination, disrespect, cutting class, tardiness, and…

Sediment accumulation and water volume in Loch Raven Reservoir, Baltimore County, Maryland

Science.gov (United States)

Banks, William S.L.; LaMotte, Andrew E.

1999-01-01

Baltimore City and its metropolitan area are supplied with water from three reservoirs, Liberty Reservoir, Prettyboy Reservoir, and Loch Raven Reservoir. Prettyboy and Loch Raven Reservoirs are located on the Gunpowder Falls (figure 1). The many uses of the reservoir system necessitate coordination and communication among resource managers. The 1996 Amendment to the Safe Drinking Water Act require States to complete source-water assessments for public drinking-water supplies. As part of an ongoing effort to provide safe drinking water and as a direct result of these laws, the City of Baltimore and the Maryland Department of the Environment (MDE), in cooperation with other State and local agencies, are studying the Gunpowder Falls Basin and its role as a source of water supply to the Baltimore area. As a part of this study, the U.S. Geological Survey (USGS), in cooperation with the Maryland Geological Survey (MGS), with funding provided by the City of Baltimore and MDE, is examining sediment accumulation in Loch Raven Reservoir. The Baltimore City Department of Public Works periodically determines the amount of water that can be stored in its reservoirs. To make this determination, field crews measure the water depth along predetermined transects or ranges. These transects provide consistent locations where water depth, or bathymetric, measurements can be made. Range surveys are repeated to provide a record of the change in storage capacity due to sediment accumulation over time. Previous bathymetric surveys of Loch Raven Reservoir were performed in 1943, 1961, 1972, and 1985. Errors in data-collection and analysis methods have been assessed and documented (Baltimore City Department of Public Works, 1989). Few comparisons can be made among survey results because of changing data-collection techniques and analysis methods.

Baltimore Air Toxics Study (BATS)

Energy Technology Data Exchange (ETDEWEB)

Sullivan, D.A. [Sullivan Environmental Consulting, Inc., Alexandria, VA (United States)

1996-12-31

The Baltimore Air Toxics Study is one of the three urban air toxics initiatives funded by EPA to support the development of the national air toxics strategy. As part of this project, the Air Quality Integrated Management System (AIMS) is under development. AIMS is designed to bring together the key components of urban air quality management into an integrated system, including emissions assessment, air quality modeling, and air quality monitoring. Urban area source emissions are computed for a wide range of pollutants and source categories, and are joined with existing point source emissions data. Measured air quality data are used to evaluate the adequacy of the emissions data and model treatments as a function of season, meteorological parameters, and daytime/nighttime conditions. Based on tested model performance, AIMS provides the potential to improve the ability to predict air quality benefits of alternative control options for criteria and toxic air pollutants. This paper describes the methods used to develop AIMS, and provides examples from its application in the Baltimore metropolitan area. The use of AIMS in the future to enhance environmental management of major industrial facilities also will be addressed in the paper.

Undergraduate Certificate in Rail Transportation/Engineering.

Science.gov (United States)

2016-05-05

A shift in the U.S. transportation environment has led to a revival in rail transport, especially in : freight rail1. In the meantime, an aging rail employee demographic presents a severe threat to : sufficient level of individuals equipped to handle...

Ruby on Rails for dummies

CERN Document Server

Burd

2007-01-01

Quickly create Web sites with this poweful tool Use this free and easy programming language for e-commerce sites and blogs If you need to build Web and database applications quickly but you don''t dream in computer code, take heart! Ruby on Rails was created for you, and this book will have you up and running in no time. The Ruby scripting language and the Rails framework let you create full-featured Web applications fast. It''s even fun! Discover how toInstall and run Ruby and RailsUse the RadRails IDECreate a blog with RubyConnect your Web site to a databaseBuild a shopping cartExplore Ruby'

A Current-Mode Common-Mode Feedback Circuit (CMFB) with Rail-to-Rail Operation

Science.gov (United States)

Suadet, Apirak; Kasemsuwan, Varakorn

2011-03-01

This paper presents a current-mode common-mode feedback (CMFB) circuit with rail-to-rail operation. The CMFB is a stand-alone circuit, which can be connected to any low voltage transconductor without changing or upsetting the existing circuit. The proposed CMFB employs current mirrors, operating as common-mode detector and current amplifier to enhance the loop gain of the CMFB. The circuit employs positive feedback to enhance the output impedance and gain. The circuit has been designed using a 0.18 μm CMOS technology under 1V supply and analyzed using HSPICE with BSIM3V3 device models. A pseudo-differential amplifier using two common sources and the proposed CMFB shows rail to rail output swing (± 0.7 V) with low common-mode gain (-36 dB) and power dissipation of 390 μW.

Effects of tunnel and station size on the costs and service of subway transit systems

Science.gov (United States)

Dayman, B., Jr.

1979-01-01

The feasibility of less spacious, less costly underground rail mass transit system designs is studied. The major cost saving expected from alternative tunnel designs results from using precast concrete segment liners in place of steel. The saying expected for a two-foot decrease in the diameter of twin, single track tunnels is about two million dollars per route mile from 13 million dollars for precast concrete segment liners (a saving of about 16%). The cost per route-mile of a double track tunnel appears to be 15 to 25% higher than for the twin, single track tunnels. The effective cost saving expected from stations with four-car train capability instead of the usual eight-car trains is nearly 25% or seven million dollars per route mile. The saving in station costs can be obtained while improving service to the user (lower transit time and less waiting for trains) up to a capacity of 36,000 riders per hour in each direction.

Rail transportation of Fernald remediation waste

International Nuclear Information System (INIS)

Fellman, R.T.; Lojek, D.A.; Motl, G.P.; Weddendorf, W.K.

1995-01-01

Remediation of the Department of Energy (DOE) Fernald site located north of Cincinnati will generate large quantities of low-level radwaste. This volume includes approximately 1,050,000 tons of material to be removed from eight waste pits comprising Operable Unit 1 (OU-1). The remedial alternative selected includes waste material excavation, drying and transportation by rail to a burial site in the arid west for disposal. Rail transportation was selected not only because rail transportation is safer than truck transportation, but also because of the sheer magnitude of the project and the availability of bulk rail car unloading facilities at a representative disposal site. Based upon current waste quantity estimates as presented in the Feasibility Study for OUI, a fully-loaded 47-car unit train would depart the Fernald site weekly for five years. This paper illustrates the steps taken to obtain agency and public acceptance of the Record of Decision for the remedy which hinged on rail transportation. A preliminary, but detailed, rail transportation plan was prepared for the project to support a series of CERCLA public meetings conducted in late 1994. Some of the major issues addressed in the plan included the following: (1) Scope of project leading to selection of rail transportation; (2) Waste classification; (3) Rail Company overview; (4) Train configuration and rail car selection; (5) Routing; (6) Safety; (7) Prior Notification Requirements (8) Emergency Response. A series of three public meetings identified a number of issues of prime concern to Fernald stakeholders. Following resolution of these issues during the public comment period, a Record of Decision (ROD) approving implementation of the rail transportation strategy was approved pending incorporation of EPA and State of Ohio comments on December 22, 1994

Rail electrodynamics in a plasma armature railgun

International Nuclear Information System (INIS)

Rolader, G.E.; Jamison, K.A.; Villecco, R.A.; Graham, F.R.

1991-01-01

A model is developed to investigate rail electrodynamics in a plasma armature railgun. This model describes the rail motion in response to the transitory Lorentz force and the compressive restoration force from the material which is between the rails and the containment structure. In this model the distance between the rails is found to oscillate with a frequency of β. The magnetic field and the dynamic behavior of the rails induce local electric fields. We investigate the significance of these electric fields in the laboratory frame and in the projectile frame. In the lab frame, rail electrodynamics induces local electric fields which have maximums spaced behind the projectile at locations where βt p is an odd multiple of π, where t p is the time since the projectile has passed an axial location on the rails. When the projectile is accelerating, rail dynamics induce electric fields in the projectile frame which have maximums where βt p is an even multiple of π. As the projectile velocity increases, the locations of the peak voltages move farther behind the projectile. For the CHECMATE railgun, calculations indicate that the rail displacement is on the order of 2 mm, the rail velocity is on the order of 50 m/s, and the voltages induced in the projectile frame are on the order of 20--40 V

The process for technology transfer in Baltimore

Science.gov (United States)

Golden, T. S.

1978-01-01

Ingredients essential for a successful decision process relative to proper technological choices for a large city were determined during four years of experience in the NASA/Baltimore Applications Project. The general approach, rationale, and process of technology transfer are discussed.

Superconducting augmented rail gun (SARG)

International Nuclear Information System (INIS)

Homan, C.G.; Cummings, C.E.; Fowler, C.M.

1986-01-01

Superconducting augmentation consists of a superconducting coil operating in the persistent mode closely coupled magnetically with a normally conducting rail gun. A theoretical investigation of the effect of this system on a rail gun has shown that two benefits occur. Projectile velocities and launch efficiencies increase significantly depending on the magnetic coupling between the rail and augmentation circuits. Previous work evaluated an idealized system by neglecting energy dissipation effects. In this paper, the authors extend the analysis to include the neglected terms and show improved actual launch efficiencies for the SARG configuration. In this paper, the authors discuss details of projectile design in depth and present preliminary results of rail gun performance

46 CFR 190.25-10 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Storm rails. 190.25-10 Section 190.25-10 Shipping COAST... ARRANGEMENT Rails and Guards § 190.25-10 Storm rails. (a) On vessels in ocean and coastwise service, suitable storm rails shall be installed in all passageways and at the deckhouse sides where persons on board...

46 CFR 72.40-10 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 3 2010-10-01 2010-10-01 false Storm rails. 72.40-10 Section 72.40-10 Shipping COAST... and Guards § 72.40-10 Storm rails. (a) Suitable storm rails shall be installed in all passageways and at the deckhouse sides where passengers or crew might have normal access. Storm rails shall be...

46 CFR 92.25-10 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 92.25-10 Section 92.25-10 Shipping COAST... ARRANGEMENT Rails and Guards § 92.25-10 Storm rails. (a) On vessels in ocean and coastwise service, suitable storm rails shall be installed in all passageways and at the deckhouse sides where persons on board...

High-strength chromium--molybdenum rails

International Nuclear Information System (INIS)

Smith, Y.E.; Sawhill, J.M. Jr.; Cias, W.W.; Eldis, G.T.

1976-01-01

A laboratory study was conducted with the aim of developing an as-rolled rail of over 100 ksi (689 N/mm 2 ) yield strength. A series of compositions providing both pearlitic and bainitic microstructures was evaluated. A fine pearlitic structure was developed in a 0.73 percent C -- 0.83 percent Mn -- 0.16 percent Si -- 0.75 percent Cr -- 0.21 percent Mo steel by simulating the mill cooling rate of 132-lb/yd (65.5-kg/m) rail. Two 100-ton commercial heats were made of this approximate composition and processed into 132-lb/yd (65.5-kg/m) rail. Samples tested in the laboratory ranged from 109 to 125 ksi (750 to 860 N/mm 2 ) in yield strength. The chromium-molybdenum rails also exhibited excellent fracture toughness and fatigue properties. Sections of the rail were joined by both flash-butt welding and thermite welding. The hardness peaks produced in the flash-butt welds could be reduced by applying either a postweld current or an induction heating cycle. The high-strength chromium-molybdenum rails have been in service for over eight months in curved sections of an ore railway that carries over 55 million gross long tons per year. 7 tables, 18 figs

Computation of wheel-rail contact force for non-mapping wheel-rail profile of Translohr tram

Science.gov (United States)

Ji, Yuanjin; Ren, Lihui; Zhou, Jinsong

2017-09-01

Translohr tram has steel wheels, in V-like arrangements, as guide wheels. These operate over the guide rails in inverted-V arrangements. However, the horizontal and vertical coordinates of the guide wheels and guide rails are not always mapped one-to-one. In this study, a simplified elastic method is proposed in order to calculate the contact points between the wheels and the rails. By transforming the coordinates, the non-mapping geometric relationship between wheel and rail is converted into a mapping relationship. Considering the Translohr tram's multi-point contact between the guide wheel and the guide rail, the elastic-contact hypothesis take into account the existence of contact patches between the bodies, and the location of the contact points is calculated using a simplified elastic method. In order to speed up the calculation, a multi-dimensional contact table is generated, enabling the use of simulation for Translohr tram running on curvatures with different radii.

Analysis of rail welding methods for mine rail access with the use of modern technologies

Science.gov (United States)

Usoltsev, A. A.; Shevchenko, R. A.; Kozyrev, N. A.; Kriukov, R. E.; Shishkin, P. E.

2017-09-01

Welded joint zones are weak sections of the railway track for all traffic cases (in the case of high-speed traffic and heavy traffic). In the paper advantages and disadvantages of the basic ways of rails welding, which are widely used today, are considered: electrocontact and aluminothermic. Carefully selected mode of differentially thermally strengthened rails string will allow the process of correction after heat treatment to be minimized and internal residual compressive stresses to be kept. Particular attention should be paid to the method of rails welding, in which after rails welding during their cooling it is offered to perform quasi-isothermal exposure in the temperature range of fine structure formation by passing pulses of alternating electric current through the welded joint maintaining this temperature until the end of the transformation. The use of quasi-isothermal exposure at a temperature of 600 - 650 °C makes it possible to obtain a finely dispersed structure of the welded seam of rails without additional heat treatment.

Rail inspection using noncontact laser ultrasonics

International Nuclear Information System (INIS)

Kim, Nak Hyeon; Sohn, Hoon; Han, Soon Woo

2012-01-01

In this study, a noncontact laser ultrasonic system is proposed for rail defect detection. An Nd Yag pulse laser is used for generation of ultrasonic waves, and the corresponding ultrasonic responses are measured by a laser Doppler vibrometer. For the detection of rail surface damages, the shape of the excitation laser beam is transformed into a line. On the other hand, a point source laser beam is used for the inspection of defects inside a rail head. Then, the interactions of propagating ultrasonic waves with defects are examined using actual rail specimens. Amplitude attenuation was mainly observed for a surface crack, and reflections were most noticeable from an internal damage. Finally, opportunities and challenges associated with real time rail inspection from a high speed train are discussed

Model for predicting the frequency of broken rails

Directory of Open Access Journals (Sweden)

S. Vesković

2012-04-01

Full Text Available Broken rails can cause train delays, trains cancelations and, unfortunately, they are common causes of accidents. This affects planning of a resources, budget and organization of railway track maintenance. Planning of railway track maintenance cannot be done without an estimation of number of rails that will be replaced due to the broken rail incidents. There are many factors that influence broken rails and the most common are: rail age, annual gross tonnage, degree of curve and temperature in the time of breakage. The fuzzy logic model uses acquired data as input variables to predict the frequency of broken rails for the certain rail types on some Sections.

46 CFR 116.920 - Storm rails.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Storm rails. 116.920 Section 116.920 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SMALL PASSENGER VESSELS CARRYING MORE THAN 150... and Guards § 116.920 Storm rails. Suitable storm rails or hand grabs must be installed where necessary...

46 CFR 177.900 - Deck rails.

Science.gov (United States)

2010-10-01

...) high. (4) While engaged in big game angling, the minimum rail height may be reduced to not less than... section as applicable must be installed when big game angling is not being conducted. (e) Where the... that a higher rail would interfere with the fishing operation and the lower rail would not...

Measles, social media and surveillance in Baltimore City.

Science.gov (United States)

Warren, Katherine E; Wen, Leana S

2017-09-01

Baltimore City was faced with two potential measles outbreaks in 2015. Both cases occurred in the wake of national media attention paid to the Disneyland outbreaks of the same year. A comparative case study approach was used applying qualitative data to elicit best practices in infectious disease protocols in the age of social media. The research also used search engine data from Google Trends to track constituent engagement over time. Across the two case studies, the Baltimore City Health Department identified a number of best practices to inform the public via social media and minimize levels of misinformation and panic. These practices included clarity in messaging across platforms and public health jurisdictions; pre-emptor alerts of potential measles cases to control and shape the media messaging; and targeted, in-person outreach to engage groups in a culturally competent manner. The Baltimore City Health Department's response drew out a critical need for re-examining infectious disease protocols in the age of social media (e.g. contact notification, quarantine, media sensitivity) and anti-vaccination movements that pose new obstacles to government intervention. The benefits and challenges of greater connectivity between providers, patients, and public health officers are discussed. © The Author 2016. Published by Oxford University Press on behalf of Faculty of Public Health. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Reduction of background noise induced by wind tunnel jet exit vanes

Science.gov (United States)

Martin, R. M.; Brooks, T. F.; Hoad, D. R.

1985-01-01

The NASA-Langley 4 x 7 m wind tunnel develops low frequency flow pulsations at certain velocity ranges during open throat mode operation, affecting the aerodynamics of the flow and degrading the resulting model test data. Triangular vanes attached to the trailing edge of flat steel rails, mounted 10 cm from the inside of the jet exit walls, have been used to reduce this effect; attention is presently given to methods used to reduce the inherent noise generation of the vanes while retaining their pulsation reduction features.

Assessment of Rail Seat Abrasion Patterns and Environment

Science.gov (United States)

2012-05-01

Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

Applying the polluter-pays principle to rail: Environmental differentiation of rail access charges

Energy Technology Data Exchange (ETDEWEB)

Pons-Rigat, A.; Turro Calvet, M.; Ubalde Claver, Ll.

2016-07-01

Environmental charges to rail service operators are still at an early stage of implementation in Europe. Current schemes are dissimilar and most of them have a very limited scope or do not provide effective incentives to abate environmental impacts. This is due to several practical difficulties in implementing internalisation pricing schemes in the railway sector. The first difficulty arises from the lack of internalisation in other transport modes and the small competitive margin of railways. Increasing the overall level of rail charges could affect their survival. A second difficulty is due to the uncertainties in the valuation of external costs and in the establishment of the optimal level of charges. On top of that, the imperfect competition in the rail market and its operational and financial rigidities imply that pricing decisions could be unfair and produce undesired demand effects. These difficulties should not prevent, however, advancing towards the application to rail of adequate charging methods for its environmental costs. This paper addresses the problem of setting environmentally differentiated rail charges through an analytical approach. A generalised formulation is developed that sets the level of charges as a function of the degree of internalisation in other modes. Then, the optimal trade-off in the level of differentiation is assessed to extract general guidelines. Based on this, both the derived overall costs and benefits and the impacts on each agent are quantified. (Author)

It's not easy going green: Obstacles to tree-planting programs in East Baltimore

Science.gov (United States)

Michael Battaglia; Geoffrey L. Buckley; Michael Galvin; Morgan. Grove

2014-01-01

In 2006, government officials in Baltimore announced plans to double the city's tree canopy over the next thirty years. While the effort has already produced positive results, many parts of the city still lack trees. In this paper we consider whether two neighborhoods in East Baltimore — Berea and Madison-Eastend — are suitable locations for tree...

A low power and low distortion rail-to-rail input/output amplifier using constant current technique

International Nuclear Information System (INIS)

Liu Yan; Zhao Yiqiang; Zhang Shilin; Zhao Hongliang

2011-01-01

A rail-to-rail amplifier with constant transconductance, intended for audio processing, is presented. The constant transconductance is obtained by a constant current technique based on the input differential pairs operating in the weak inversion region. MOSFETs working in the weak inversion region have the advantages of low power and low distortion. The proposed rail-to-rail amplifier, fabricated in a standard 0.35 μm CMOS process, occupies a core die area of 75 x 183 μm 2 . Measured results show that the maximum power consumption is 85.37 μW with a supply voltage of 3.3 V and the total harmonic distortion level is 1.2% at 2 kHz. (semiconductor integrated circuits)

Rail gun powered by an integral explosive generator

International Nuclear Information System (INIS)

Peterson, D.R.; Fowler, C.M.

1979-01-01

We propose the use of a rail gun powered by an explosive magnetic flux compression generator built into the rail gun itself in which the rails of the gun are driven together behind the projectile by explosives. The magnetic field established between the rails by an initial current supplied by an external source at the breech of the gun is trapped and compressed by the collapsing rails to accelerate the projectile down the bore of the gun

Baltimore: A Multifaceted Approach to Developing Relationships

Science.gov (United States)

Durham, Rachel E.; Shiller, Jessica; Connolly, Faith

2018-01-01

As community schools spread across the country, community school staff need effective approaches to engaging families and community-based partners. Such principles must be broadly applicable, given community schools' mandate to adapt to different local contexts. Based on recent research on Baltimore City's community schools, the authors highlight…

78 FR 57450 - State Rail Plan Guidance

Science.gov (United States)

2013-09-18

... of impact assessment required for the rail infrastructure, facilities, and service improvements contained in State rail plans. Other issues raised by commenters included the importance of involving... to emphasize the importance of preparing State rail plans within the policy and procedural contexts...

Urban Waters and the Patapsco Watershed/Baltimore Region (Maryland)

Science.gov (United States)

Patapsco Watershed / Baltimore Area of the Urban Waters Federal Partnership (UWFP) reconnects urban communities with their waterways by improving coordination among federal agencies and collaborating with community-led efforts.

Momentum equation for arc-driven rail guns

International Nuclear Information System (INIS)

Batteh, J.H.

1984-01-01

In several models of arc-driven rail guns, the rails are assumed to be infinitely high to simplify the calculation of the electromagnetic fields which appear in the momentum equation for the arc. This assumption leads to overestimates of the arc pressures and accelerations by approximately a factor of 2 for typical rail-gun geometries. In this paper, we develop a simple method for modifying the momentum equation to account for the effect of finite-height rails on the performance of the rail gun and the properties of the arc. The modification is based on an integration of the Lorentz force across the arc cross section at each axial location in the arc. Application of this technique suggests that, for typical rail-gun geometries and moderately long arcs, the momentum equation appropriate for infinite-height rails can be retained provided that the magnetic pressure term in the equation is scaled by a factor which depends on the effective inductance of the gun. The analysis also indicates that the magnetic pressure gradient actually changes sign near the arc/projectile boundary because of the magnetic fields associated with the arc current

Electron emission at the rail surface

International Nuclear Information System (INIS)

Thornhill, L.; Battech, J.

1991-01-01

In this paper the authors examine the processes by which current is transferred from the cathode rail to the plasma armature in an arc-driven railgun. Three electron emission mechanisms are considered, namely thermionic emission, field-enhanced thermionic emission (or Schottky emission), and photoemission. The author's calculations show that the dominant electron emission mechanism depends, to a great extent, on the work function of the rail surface, the rail surface temperature, the electric field at the rail surface, and the effective radiation temperature of the plasma. For conditions that are considered to be typical of a railgun armature, Schottky emission is the dominant electron emission mechanism, providing current densities on the order of 10 9 A/m 2

Rail-guided robotic end-effector position error due to rail compliance and ship motion

NARCIS (Netherlands)

Borgerink, Dian; Stegenga, J.; Brouwer, Dannis Michel; Woertche, H.J.; Stramigioli, Stefano

2014-01-01

A rail-guided robotic system is currently being designed for the inspection of ballast water tanks in ships. This robotic system will manipulate sensors toward the interior walls of the tank. In this paper, the influence of rail compliance on the end-effector position error due to ship movement is

Keeping rail on track: preliminary findings on safety culture in Australian rail.

Science.gov (United States)

Blewett, Verna; Rainbird, Sophia; Dorrian, Jill; Paterson, Jessica; Cattani, Marcus

2012-01-01

'Safety culture' is identified in the literature as a critical element of healthy and safe workplaces. How can rail organizations ensure that consistently effective work health and safety cultures are maintained across the diversity of their operations? This paper reports on research that is currently underway in the Australian rail industry aimed at producing a Model of Best Practice in Safety Culture for the industry. Located in rail organizations dedicated to the mining industry as well as urban rail and national freight operations, the research examines the constructs of organizational culture that impact on the development and maintenance of healthy and safe workplaces. The research uses a multi-method approach incorporating quantitative (survey) and qualitative (focus groups, interviews and document analysis) methods along with a participative process to identify interventions to improve the organization and develop plans for their implementation. The research uses as its analytical framework the 10 Platinum Rules, from the findings of earlier research in the New South Wales (Australia) mining industry, Digging Deeper. Data collection is underway at the time of writing and preliminary findings are presented at this stage. The research method may be adapted for use as a form of organizational review of safety and health in organizational culture.

Research on Miniature Calibre Rail-Guns for the Mechanical Arm

Directory of Open Access Journals (Sweden)

Ronggang Cao

2017-01-01

Full Text Available Rail-gun should not only be used to military applications, but also can be developed as applications in the civilian aspects of the market. With the development of the electromagnetic launch technology, based on the similarity theory, using the existing rail-gun model to guide the construction of more economical miniature calibre rail-guns, and apply it in some machinery and equipment, this idea will open up a wider rail-gun application space. This article will focus on the feasibility of application of miniature calibre rail-guns in the mechanical arm. This paper designs the schematic diagram, then theoretical analyzes force conditions of the armature in the mechanical arm, calculates the possible range of the current amplitude and so on. The existing rail-gun model can be used to guides design the circuit diagram of the miniature calibre rail-gun. Based on the similarity theory and many simulation experiments, designed the experimental parameters of a miniature rail-gun and analyzed the current, Lorentz force, velocity, and location of the existing rail-gun and miniature rail-gun. The results show that the rail-gun launching technology applied to robot arms is feasibility. The application of miniature calibre rail-guns in the mechanical arm will benefit to the further development of rail-guns.

The NASA/Baltimore Applications Project (BAP). Computer aided dispatch and communications system for the Baltimore Fire Department: A case study of urban technology application

Science.gov (United States)

Levine, A. L.

1981-01-01

An engineer and a computer expert from Goddard Space Flight Center were assigned to provide technical assistance in the design and installation of a computer assisted system for dispatching and communicating with fire department personnel and equipment in Baltimore City. Primary contributions were in decision making and management processes. The project is analyzed from four perspectives: (1) fire service; (2) technology transfer; (3) public administration; and (5) innovation. The city benefitted substantially from the approach and competence of the NASA personnel. Given the proper conditions, there are distinct advantages in having a nearby Federal laboratory provide assistance to a city on a continuing basis, as is done in the Baltimore Applications Project.

Flex Cargo Rail. Developing new service, collection and distribution concepts for the transport of freight by rail.; Flex Cargo Rail. Wege zu neuen Bedien-, Sammel- und Verteilkonzepten im Schienengueterverkehr

Energy Technology Data Exchange (ETDEWEB)

Kochsiek, Joachim [Fraunhofer-Institut fuer Materialfluss und Logistik (IML), Dortmund (Germany). Gruppe Multimodale Logistik

2010-07-01

FlexCargoRail is a concept for self propelled electric freight wagons. This will enhance rail operations on first and last mile. The concept can be integrated in the existing rail system, so migration is possible without any lost investments. Standard components from industry and rail are used to realise the FCR wagon. Motors, transmissions, control and batteries are available and approved. One of the effects is to enhance service for loading terminals. This can become independent from factory siding operation. From the economic point of view, FCR is realisable. This is shown by target costing. Efficiency of FCR is dependent from high frequent use of FCR rail cars and the use of the possibility to shunt also conventional freight wagons with FCR wagons. Migration should be carried out in logistical networks with frequent operations between plants and sidings with a closed wagon pool. (orig.)

A Rails / Django Comparison

Directory of Open Access Journals (Sweden)

2008-06-01

Full Text Available Ruby on Rails (“Rails” is the dominant web programming framework for Ruby and, even outside the Ruby community, is considered the epitome of the latest generation of high-productivity, open source web development tools. Django is one of many competing web development frameworks for Python. It is notable, first, for being highly regarded amongst Python programmers, and second, for being one of the few of the new generation of framework that does not ape Ruby on Rails. Both Rails and Django claim greatly enhanced productivity, compared with more traditional web development frameworks. In this paper, we compare the two frameworks from the point of view of a developer attempting to choose one of the two frameworks for a new project.

Excitation of Surface Electromagnetic Waves on Railroad Rail

Science.gov (United States)

1978-03-31

UMTA's Office of Rail Technology research programs aim to improve urban rail transportation systems safety. This rail-transit research study attempts to develop an onboard, separate and independent obstacle-detection system--Surface Electromagnetic W...

A School Voucher Program for Baltimore City

Science.gov (United States)

Lips, Dan

2005-01-01

Baltimore City's public school system is in crisis. Academically, the school system fails on any number of measures. The city's graduation rate is barely above 50 percent and students continually lag well behind state averages on standardized tests. Adding to these problems is the school system's current fiscal crisis, created by years of fiscal…

Future Parking Demand at Rail Stations in Klang Valley

Directory of Open Access Journals (Sweden)

Ho Phooi Wai

2017-01-01

Full Text Available Klang Valley, Malaysia is currently undergoing a massive development of rail transportation system expansion where the current integrated rail transit system will see new extensions of two MRT lines and an LRT line by year 2020. By year 2017, the first MRT line will be ready to run with 31 new rail stations connected to the current passenger rail network. The existing Park and Ride facilities in Klang Valley are commonly known as being unable to sufficiently cater for the current parking space demand. Therefore, with the expansion of many additional rail stations which are rapidly under construction, there are doubts that the future parking space at rail stations will be able to accommodate the sudden rise of rail passengers. Although the authorities are increasing parking bays at various locations, will the future parking demand at rail stations be sufficient? This paper studies the factors influencing parking demand in terms of population, car ownership, new car registrations and passenger rail ridership and estimating the future parking demand using Linear Regression method. Result shows that the forecasted parking demand at rail stations after the implementation of the first new MRT system in 2017 is 2.7 times more than in 2014.

Characterization of deformed pearlitic rail steel

Science.gov (United States)

Nikas, Dimitrios; Meyer, Knut Andreas; Ahlström, Johan

2017-07-01

Pearlitic steels are commonly used for railway rails because they combine good strength and wear properties. During service, the passage of trains results in a large accumulation of shear strains in the surface layer of the rail, leading to crack initiation. Knowledge of the material properties in this region is therefore important for fatigue life prediction. As the strain is limited to a thin surface layer, very large strain gradients can be found. This makes it very difficult to quantify changes in material behavior. In this study hardness measurements were performed close to the surface using the Knoop hardness test method. The orientation of the pearlitic lamellas was measured to give an overview of the deformed microstructure in the surface of the rail. Microstructural characterization of the material was done by optical microscopy and scanning electron microscopy to evaluate the changes in the microstructure due to the large deformation. A strong gradient can be observed in the top 50 μm of the rail, while deeper into the rail the microstructure of the base material is preserved.

Rail-to-rail low-power fully differential OTA utilizing adaptive biasing and partial feedback

DEFF Research Database (Denmark)

Tuan Vu, Cao; Wisland, Dag T.; Lande, Tor Sverre

consumption. The DC-gain of the proposed OTA is improved by adding a partial feedback loop. A Common-Mode Feedback (CMFB) circuit is required for fully differential rail-to-rail operation. Simulations show that the OTA topology has a low stand-by power consumption of 96μW and a high FoM of 3.84 [(V...

76 FR 50717 - Foreign-Trade Zone 74, Baltimore, MD; Application for Reorganization/Expansion Under Alternative...

Science.gov (United States)

2011-08-16

... 28 (2.5 acres)-- McCormick & Company, Inc., 11102 McCormick Road, Hunt Valley (Baltimore County); Proposed Site 29 (17.6 acres)--McCormick & Company, Inc., 10901 Gilroy Road, Hunt Valley (Baltimore County); and, Proposed Site 30 (8.48 acres)--McCormick & Company, Inc., 4607 Appliance Drive, Belcamp (Harford...

Vibroacoustical analysis of rail vehicle

Directory of Open Access Journals (Sweden)

Králíček J.

2007-11-01

Full Text Available The article deals with the vibroacoustical analysis of rail vehicle and is the extension of the previously presented work “Modelování podvozku kolejového vozidla s poddajným rámem”. The vibroacoustical analysis uses the outcomes of the dynamical analysis of rail vehicle bogie i.e. surface velocities of the bogie frame to compute the acoustic power radiated by the bogie frame and forces acting in the bogie-body interface. The radiated power and the force spectra are then used as the excitation to the rail body model in the environment Auto-SEA to compute the interior acoustic quantities.

Complex eigenvalue analysis of railway wheel/rail squeal

African Journals Online (AJOL)

DR OKE

Squeal noise from wheel/rail and brake disc/pad frictional contact is typical in railways. ... squeal noise by multibody simulation of a rail car running on rigid rails. ... system, traditional complex eigenvalue analysis by finite element was used.

High Speed Rail (HSR) in the United States

Science.gov (United States)

2009-12-08

announced that it will expand the capacity on its aging high speed line between Tokyo and Osaka, the most heavily traveled intercity rail segment in the...United States, in most of these countries intercity rail travel (including both conventional and high speed rail) represents less than 10% of all...that is sometimes mentioned by its advocates. Intercity passenger rail transport is relatively safe, at least compared with highway travel . And HSR in

The geographic epidemiology of Mycobacterium tuberculosis disease in Baltimore, 1971-1995

Science.gov (United States)

Obasanjo, Olugbenga Olufemi

Given the reemergence of Tuberculosis (TB) in the United States (U.S.) in the 1980s and 1990s, several strategies have emerged to combat the disease. A successful tool has been Directly Observed Therapy (DOT). Chaulk, et al. showed that DOT was responsible for the maintaining the decline in TB rates in Baltimore through the corresponding period of an upswing in rates nationally. In this study, we measure the impact of DOT on the geographic pattern of TB in Baltimore. We used Geographical Information System (GIS) methods to compare the geographic patterns of TB in Baltimore before and after the introduction of DOT in the city. We identified both predictors of TB, and differences in geographic units in Baltimore over time. We measured the impact of the introduction of DOT and Rifampin on various treatment outcomes for TB at about the same time. Despite the drop in numbers of TB cases, the spatial distribution of cases generally remained unchanged until 1995. This was confirmed by the fact that similar predictors were identified in all of the years that were analyzed. However, higher proportions of TB cases were found among blacks and females in more recent years. Death rates have increased significantly while corresponding relapse rates and the mean length of therapy have declined significantly. Rifampin was associated with a longer length of therapy before DOT, but with a shorter duration of therapy following the introduction of DOT. In all of the years analyzed, losses to follow-up (LTFU) do not differ from those completing therapy and are not spatially clustered relative to those completing therapy. DOT has been effective in reducing the numbers of TB cases in Baltimore city-wide without an emphasis on so-called "high-risk" patients for LTFU. Thus, any declines in TB case rates are not due to a decline in a particular group or geographic sector of the city. Universal DOT is effective and does not cause a geographic clustering of difficult-to-reach patients. This

Sectional Rail System as Base for a Plate Covering

DEFF Research Database (Denmark)

2015-01-01

The present invention concerns a sectional rail system which is constructed with the known outer rails with U-shaped cross-section and intermediate rails with C-shaped cross-section, and which is peculiar in that each of the retention means of the outer rail includes at least one stop pin which i...

75 FR 17462 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-04-06

... decision may be purchased by contacting the office of Public Assistance, Governmental Affairs, and...-2)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2010 Rail Cost...

The rail abandonment process: A southern perspective

International Nuclear Information System (INIS)

1988-12-01

One factor in evaluating the desirability of rail transport for high-level radioactive wastes or spent fuels is the frequency, or lack thereof, with which railroad and railroad lines have been, and are, abandoned. If DOE makes a decision to use the rail option and a line is subsequently abandoned, the choice results in increased cost, time delays and possibly safety problems: Information is therefore needed prior to the decision-making process to evaluate the desirability of the rail shipping option. One result of the abandonments mentioned herein, as well as other later abandonments, is the creation of a US rail system undergoing an evolutionary process in the 1980s as far-reaching as the changes that occurred when the industry was in its infancy a century and-a-half ago. The purpose of this paper is to examine the factors leading to some of these changes by tracing the historical development of the rail abandonment process, with particular emphasis on the rise of regional railroads, their problems in the modern era and current trends in rail abandonments as well as their effects on the southeastern United States

49 CFR 37.79 - Purchase or lease of new rail vehicles by public entities operating rapid or light rail systems.

Science.gov (United States)

2010-10-01

... entities operating rapid or light rail systems. 37.79 Section 37.79 Transportation Office of the Secretary... operating rapid or light rail systems. Each public entity operating a rapid or light rail system making a... system shall ensure that the vehicle is readily accessible to and usable by individuals with disabilities...

Can urban rail transit curb automobile energy consumption?

International Nuclear Information System (INIS)

Lin, Boqiang; Du, Zhili

2017-01-01

With the rapid development of China's economy and the speed of urbanization, China's automobile sector has experienced rapid development. The rapid development of the automobile sector has increased energy consumption. According to the results of this paper, automobile energy consumption accounted for about 10.73% of total energy consumption in China in 2015, about 3.6 times the proportion a decade ago. With the deterioration of urban traffic conditions, relying on expanding the amount of vehicles and city road network cannot solve the problem. Urban rail transit is energy-saving and less-polluting, uses less space, has large capacity, and secure. Urban rail transit, according to the principle of sustainable development, is a green transportation system and should be especially adopted for large and medium-sized cities. The paper uses the binary choice model (Probit and Logit) to analyze the main factors influencing the development of rail transit in Chinese cities, and whether automobile energy consumption is the reason for the construction of urban rail transit. Secondly, we analyze the influence of urban rail transit on automobile energy consumption using DID model. The results indicate that the construction of urban rail traffic can restrain automobile energy consumption significantly, with continuous impact in the second year. - Highlights: • Investigate the main factors influencing the building of rail transit for Chinese cities. • Analyze the influence of urban rail transit on automobile energy consumption by DID model. • The results indicate that the construction of urban rail traffic can restrain automobile energy consumption significantly.

Two-Dimensional Impact Reconstruction Method for Rail Defect Inspection

Directory of Open Access Journals (Sweden)

Jie Zhao

2014-01-01

Full Text Available The safety of train operating is seriously menaced by the rail defects, so it is of great significance to inspect rail defects dynamically while the train is operating. This paper presents a two-dimensional impact reconstruction method to realize the on-line inspection of rail defects. The proposed method utilizes preprocessing technology to convert time domain vertical vibration signals acquired by wireless sensor network to space signals. The modern time-frequency analysis method is improved to reconstruct the obtained multisensor information. Then, the image fusion processing technology based on spectrum threshold processing and node color labeling is proposed to reduce the noise, and blank the periodic impact signal caused by rail joints and locomotive running gear. This method can convert the aperiodic impact signals caused by rail defects to partial periodic impact signals, and locate the rail defects. An application indicates that the two-dimensional impact reconstruction method could display the impact caused by rail defects obviously, and is an effective on-line rail defects inspection method.

Environmental impact assessment of rail infrastructure.

Science.gov (United States)

2016-01-29

This project resulted in three products: a comprehensive "Sustainable Rail Checklist," a rail planning GIS database, and a web GIS tool that integrates sustainability metrics and facilitates a rapid assessment before a formal NEPA process is implemen...

Three-dimensional rail-current distribution near the armature of simple, square-bore, two-rail railguns

International Nuclear Information System (INIS)

Beno, J.H.

1991-01-01

In this paper vector potential is solved as a three dimensional, boundary value problem for a conductor geometry consisting of square-bore railgun rails and a stationary armature. Conductors are infinitely conducting and perfect contact is assumed between rails and the armature. From the vector potential solution, surface current distribution is inferred

77 FR 69769 - Solid Waste Rail Transfer Facilities

Science.gov (United States)

2012-11-21

...] Solid Waste Rail Transfer Facilities AGENCY: Surface Transportation Board, DOT. ACTION: Final rules. SUMMARY: These final rules govern land-use-exemption permits for solid waste rail transfer facilities. The... Transportation Board over solid waste rail transfer facilities. The Act also added three new statutory provisions...

76 FR 80448 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-12-23

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. EP 290 (Sub-No. 5) (2012-1)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the first quarter 2012 rail cost adjustment factor (RCAF...

76 FR 59483 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-09-26

... the decision may be purchased by contacting the Office of Public Assistance, Governmental Affairs, and...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2011 Rail Cost Adjustment...

49 CFR 37.81 - Purchase or lease of used rail vehicles by public entities operating rapid or light rail systems.

Science.gov (United States)

2010-10-01

... entities operating rapid or light rail systems. 37.81 Section 37.81 Transportation Office of the Secretary... operating rapid or light rail systems. (a) Except as provided elsewhere in this section, each public entity operating a rapid or light rail system which, after August 25, 1990, purchases or leases a used rapid or...

Accountable Talk: "Real" Conversations in Baltimore City Schools

Science.gov (United States)

Ahmann, Chloe

2017-01-01

This article examines the fundamental disconnect between discourses of accountability in education policy and their interpretation on the ground by parents. Based on data from two sites in Baltimore--district-led teacher training and a community facing school restructuring--I argue that both parents and education professionals consider…

Capistrano and the Rails Application Lifecycle

CERN Document Server

Mornini, Tom

2006-01-01

Learn how to make your Rails deployments pain-free with Capistrano! This Short Cut shows you how to use Capistrano to automate the deployment of your Rails applications. It teaches you the basics, but also goes far beyond. It shows you realistic deployment scenarios, including some with complex server farms. It includes a quick reference to Capistrano. As your Rails applications grow, it becomes increasingly important to automate deployment and to keep your development environment well organized. Capistrano is the right tool for the job, and this PDF shows you how to use it effectively.

Electromagnetic acceleration studies with augmented rails

International Nuclear Information System (INIS)

Maruo, T.; Fujioka, K.; Nagaoka, K.; Okamoto, A.; Ikuta, K.; Nemoto, K.

1991-01-01

A comparative study of electromagnetic acceleration in the rail-type accelerators with two kinds of rail geometry was carried out experimentally. The accelerators were energized by 200kJ capacitor bank and the weight of loaded projectiles was about 1.3 grams with 10mm x 10mm square bore. The attained velocity was 4.3km/s in the augmented accelerator, while it was 3.8km/s in the classical device. In this paper these differences in attained velocity are briefly discussed. A theoretical understanding of the rail erosion is also described

75 FR 35877 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-06-23

... available on our Web site, http://www.stb.dot.gov . Copies of the decision may be purchased by contacting...-3)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2010 rail cost...

76 FR 37191 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-06-24

... our Web site, http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2011 Rail Cost Adjustment...

75 FR 80895 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-12-23

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the first quarter 2011 Rail Cost Adjustment...

77 FR 37958 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-06-25

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the third quarter 2012 rail cost adjustment...

78 FR 37660 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2013-06-21

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board approves the third quarter 2013 Rail Cost Adjustment Factor...

78 FR 17764 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2013-03-22

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2013 Rail Cost Adjustment...

76 FR 16037 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2011-03-22

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the second quarter 2011 Rail Cost Adjustment...

75 FR 58019 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2010-09-23

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2010 Rail Cost Adjustment...

Hard-driven rail-gun tests

International Nuclear Information System (INIS)

Peterson, D.R.; Adams, D.F.; Cummings, C.E.; Fowler, C.M.; Kerrisk, J.F.; Marsh, S.P.; Parker, J.V.

1983-01-01

A number of prototype rail-gun designs have been tested, powered by explosive magnetic flux compression generators. Peak currents as high as 1.3 MA were delivered. Rail guns with 50-mm-thick Kevlar fiberwound structural shells were able to survive these high currents with minimum mechanical damage and were refired after enlarging the bores 0.2 to 0.4 mm to remove arc damage. In some tests, mechanical damage occurred that was apparently caused by the rebound of the gun after firing. Although the Kevlar shells had more than adequate strength, they appeared to lack sufficient stiffness, allowing excessive deflections. The use of a steel structural shell with a Kevlar sleeve was an improvement. Intrusion into the seams of the rail guns and condensation of material from the plasma armature were observed. Improved sealing of seams is indicated. In some cases, we suspect maldistribution of current within the gun; that is, not all the current delivered to the breech of the gun seemed to reach the plasma armature. Experiments are being designed to quantify the effects discussed. Rail guns of advanced design are being fabricated. An 18-g titanium projectile was accelerated to 2.4 km/s in a 16-mm-round-bore, 0.6-m-long gun, 4-6 g polycarbonate projectiles were accelerated to 3.5 km/s in 13-mm-square-bore, 1.2-m-long rail guns. All tests were conducted at atmospheric pressure

Factors affecting commuter rail energy efficiency.

Science.gov (United States)

2016-02-17

The objective of this study is to develop a planninglevel model of commuter rail energy efficiency. The : environmental benefits of commuter rail are often cited as one of the key benefits and motivators for its rapid development as a public trans...

78 FR 71724 - Rail Depreciation Studies

Science.gov (United States)

2013-11-29

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board Rail Depreciation Studies AGENCY: Surface Transportation Board, DOT. ACTION: Notice of OMB Approval of Information Collection. SUMMARY... collection, Rail Depreciation Studies. See 78 FR 18676 (Mar. 27, 2013). This collection, codified at 49 CFR...

76 FR 4284 - Grant of Authority for Subzone Status; Tulkoff Food Products, Inc. (Dehydrated Garlic), Baltimore...

Science.gov (United States)

2011-01-25

... Status; Tulkoff Food Products, Inc. (Dehydrated Garlic), Baltimore, MD Pursuant to its authority under..., has made application to the Board for authority to establish a special-purpose subzone at the garlic... garlic products at the Tulkoff Food Products, Inc., facility located in Baltimore, Maryland (Subzone 74C...

77 FR 58910 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-09-24

..., http://www.stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the fourth quarter 2012 rail cost adjustment factor (RCAF...

Analysis of minimum rail size in heavy axle load environment

Science.gov (United States)

2013-04-15

The effects of increasing axle loads on rail integrity are examined in this paper. In the present context, rail integrity refers to the prevention and control of rail failures. Rail failures usually occur because cracks or defects develop and grow fr...

Forecasted electric power demands for the Baltimore Gas and Electric Company. Volume 1 and Volume 2. Documentation manual

International Nuclear Information System (INIS)

Estomin, S.L.; Beach, J.E.; Goldsmith, J.V.

1991-05-01

The two-volume report presents the results of an econometric forecast of peak load and electric power demand for the Baltimore Gas and Electric Company (BG ampersand E) through the year 2009. Separate energy sales models were estimated for residential sales in Baltimore City, residential sales in the BG ampersand E service area excluding Baltimore City, commercial sales, industrial sales, streetlighting sales, and Company use plus losses. Econometric equations were also estimated for electric space heating and air conditioning saturation in Baltimore City and in the remainder of the BG ampersand E service territory. In addition to the energy sales models and the electric space conditioning saturation models, econometric models of summer and winter peak demand on the BG ampersand E system were estimated

Detection method based on Kalman filter for high speed rail defect AE signal on wheel-rail rolling rig

Science.gov (United States)

Hao, Qiushi; Shen, Yi; Wang, Yan; Zhang, Xin

2018-01-01

Nondestructive test (NDT) of rails has been carried out intermittently in traditional approaches, which highly restricts the detection efficiency under rapid development of high speed railway nowadays. It is necessary to put forward a dynamic rail defect detection method for rail health monitoring. Acoustic emission (AE) as a practical real-time detection technology takes advantage of dynamic AE signal emitted from plastic deformation of material. Detection capacities of AE on rail defects have been verified due to its sensitivity and dynamic merits. Whereas the application under normal train service circumstance has been impeded by synchronous background noises, which are directly linked to the wheel speed. In this paper, surveys on a wheel-rail rolling rig are performed to investigate defect AE signals with varying speed. A dynamic denoising method based on Kalman filter is proposed and its detection effectiveness and flexibility are demonstrated by theory and computational results. Moreover, after comparative analysis of modelling precision at different speeds, it is predicted that the method is also applicable for high speed condition beyond experiments.

The Homogeneity Research of Urban Rail Transit Network Performance

Directory of Open Access Journals (Sweden)

Wang Fu-jian

2016-01-01

Full Text Available Urban Rail Transit is an important part of the public transit, it is necessary to carry out the corresponding network function analysis. Previous studies mainly about network performance analysis of a single city rail transit, lacking of horizontal comparison between the multi-city, it is difficult to find inner unity of different Urban Rail Transit network functions. Taking into account the Urban Rail Transit network is a typical complex networks, so this paper proposes the application of complex network theory to research the homogeneity of Urban Rail Transit network performance. This paper selects rail networks of Beijing, Shanghai, Guangzhou as calculation case, gave them a complex network mapping through the L, P Space method and had a static topological analysis using complex network theory, Network characteristics in three cities were calculated and analyzed form node degree distribution and node connection preference. Finally, this paper studied the network efficiency changes of Urban Rail Transit system under different attack mode. The results showed that, although rail transport network size, model construction and construction planning of the three cities are different, but their network performance in many aspects showed high homogeneity.

75 FR 17203 - National Rail Plan

Science.gov (United States)

2010-04-05

... Rail Plan AGENCY: Federal Railroad Administration (FRA), Department of Transportation (DOT). ACTION... input into the development of the long-range National Rail Plan (NRP) through an open docket. In addition, the notice presents the overall plan design, Federal Railroad Administration's (FRA) goals in...

Ceramic Rail-Race Ball Bearings

Science.gov (United States)

Balzer, Mark A.; Mungas, Greg S.; Peters, Gregory H.

2010-01-01

Non-lubricated ball bearings featuring rail races have been proposed for use in mechanisms that are required to function in the presence of mineral dust particles in very low-pressure, dry environments with extended life. Like a conventional ball bearing, the proposed bearing would include an inner and an outer ring separated by balls in rolling contact with the races. However, unlike a conventional ball bearing, the balls would not roll in semi-circular or gothic arch race grooves in the rings: instead, the races would be shaped to form two or more rails (see figure). During operation, the motion of the balls would push dust particles into the spaces between the rails where the particles could not generate rolling resistance for the balls

Rails - Spears and Didion Ranches [ds310

Data.gov (United States)

California Natural Resource Agency — These data are the detections of Virginia rail (Rallus limicola), Sora (Porzana carolina), and California black rail (Laterallus jamaicensis) from 13 survey points...

Outcome of rail fixator system in reconstructing bone gap

Directory of Open Access Journals (Sweden)

Amit Lakhani

2014-01-01

Conclusion: All patients well tolerated rail fixator with good functional results and gap reconstruction. Easy application of rail fixator and comfortable distraction procedure suggest rail fixator a good alternative for gap reconstruction of limbs.

Chicago-St. Louis high speed rail plan

International Nuclear Information System (INIS)

Stead, M.E.

1994-01-01

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team's analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor

Chicago-St. Louis high speed rail plan

Energy Technology Data Exchange (ETDEWEB)

Stead, M.E.

1994-12-31

The Illinois Department of Transportation (IDOT), in cooperation with Amtrak, undertook the Chicago-St. Louis High Speed Rail Financial and Implementation Plan study in order to develop a realistic and achievable blueprint for implementation of high speed rail in the Chicago-St. Louis corridor. This report presents a summary of the Price Waterhouse Project Team`s analysis and the Financial and Implementation Plan for implementing high speed rail service in the Chicago-St. Louis corridor.

Grinding induced martensite on the surface of rails

DEFF Research Database (Denmark)

Rasmussen, C.J.; Zhang, Xiaodan; Danielsen, Hilmar Kjartansson

2014-01-01

determined. Two different rail types R260 and R350HT that both had been ground by a grinding train were investigated. The rail sections, studied using optical and scanning electron microscopy, showed that the surface of both types of rails is covered with WELs. The hardness of the WEL is increased compared...

Kinematic analysis on rail development into vacuum vessel for ITER blanket maintenance

International Nuclear Information System (INIS)

Kakudate, Satoshi; Shibanuma, Kiyoshi

2006-01-01

The vehicle manipulator system for blanket maintenance is used as a main driving mechanism for rail development, and three driving mechanisms d1, d2 (or d2') and d3 are used as cycle sequence of the repeated operations for rail development. This repeated operation can develop the articulated rail into the vacuum vessel. The rail development scenario, kinematic analysis model for rail development without any driving mechanisms in the rail joints, equations defined the angular between two rail links, identification of rail link at repeated operation, numerical analysis results on rail deployment under the forced position control of l i+1 , new rail development scenario using two driving mechanisms d1 and d2''under one cycle sequence of the repeated operations, and rail development test are reported. (S.Y.)

A low-offset low-voltage CMOS Op Amp with rail-to-rail input and output ranges

NARCIS (Netherlands)

Holzmann, Peter J.; Wiegerink, Remco J.; Gierkink, Sander L.J.; Wassenaar, R.F.; Stroet, Peter; Stroet, P.M.

1996-01-01

A low voltage CMOS op amp is presented. The circuit uses complementary input pairs to achieve a rail-to-rail common mode input voltage range. Special attention has been given to the reduction of the op amp's systematic offset voltage. Gain boost amplifiers are connected in a special way to provide

Potential scenarios of concern for high speed rail operations

Science.gov (United States)

2011-03-16

Currently, multiple operating authorities are proposing the : introduction of high-speed rail service in the United States. : While high-speed rail service shares a number of basic : principles with conventional-speed rail service, the operational : ...

Civic Engagement and Gentrification Issues in Metropolitan Baltimore

Science.gov (United States)

Durington, Matthew; Maddox, Camee; Ruhf, Adrienne; Gass, Shana; Schwermer, Justin

2009-01-01

Since the fall of 2006 a number of Towson University students concentrating in the discipline of anthropology have been part of a civic engagement and service-learning project focusing on an historic African-American community in Baltimore. While the focus of the research project concentrates on the processes of gentrification, individual student…

The latest technical solutions in rail vehicles drives

Directory of Open Access Journals (Sweden)

Andrzejewski Maciej

2017-01-01

Full Text Available The article discusses the latest trends and solutions used in the offers of rail vehicles manufacturers. The study is mainly concerned with the technical solutions used in hybrid rail vehicles, whose development has become one of the priorities for the development of rail vehicles in the European Union in recent years. Stricter emissions standards for harmful compounds in the European Union have forced manufacturers to use increasingly sophisticated technology, including hybrid drives and alternative fuels. The products and solutions offered by the major manufacturers on the market, along with their capabilities and future applications are described. The predicted trends in the development of propulsion technology for rail and road-rail vehicles are also indicated in view of the current legislative aspirations among the EU Member States.

Linear friction welding for constructing and repairing rail for high speed and intercity passenger service rail : final report.

Science.gov (United States)

2016-08-01

This project developed a solid-state welding process based on linear friction welding (LFW) technology. While resistance flash welding or : thermite techniques are tried and true methods for joining rails and performing partial rail replacement repai...

A 0.8V, 7μA, rail-to-rail input/output, constant Gm operational amplifier in standard digital 0.18μm CMOS

DEFF Research Database (Denmark)

Citakovic, J; Nielsen, I. Riis; Nielsen, Jannik Hammel

2005-01-01

A two-stage amplifier, operational at 0.8V and drawing 7μA, has been integrated in a standard digital 0.18μm CMOS process. Rail-to-rail operations at the input are enabled by complementary transistor pairs with gm control. The efficient rail-to-rail output stage is biased in class AB. The measured...

Acces to railway stations and its potential in increasing rail use

NARCIS (Netherlands)

Brons, M.R.E.; Givoni, M.; Rietveld, P.

2008-01-01

The propensity to travel by rail, and not, for example by car, can be considered to be a factor of the rail service offered, the access to it and the characteristics of the population served. Efforts to increase rail use usually focus on the rail service itself while the accessibility of the rail

Assessment of rail long-pitch corrugation

Science.gov (United States)

Valehrach, Jan; Guziur, Petr; Riha, Tomas; Plasek, Otto

2017-09-01

The paper focuses on defects of the running surface of the rail, namely the rail corrugation defect and specifically long-pitch corrugation in curves of small radii. These defects cause a shorter life of the rails, greater maintenance costs and increase the noise and vibration pollution. Therefore, it is very important to understand the formation and development of the imperfection of the rails. In the paper, various sections of railway tracks in the Czech Republic are listed, each of them completed with comparison of defect development, the particular track superstructure, rolling stock, axle load, traffic load etc. Based on performed measurements, defect development has been proved as different on sections with similar (or even same) parameters. The paper assumes that a train velocity is the significant circumstance for defect development rates. Assessment of track section with under sleeper pads, which are expected to be the one of the possible ways to suppress the corrugation defect development, is included in evaluation.

Rail Vehicle Vibrations Control Using Parameters Adaptive PID Controller

Directory of Open Access Journals (Sweden)

Muzaffer Metin

2014-01-01

Full Text Available In this study, vertical rail vehicle vibrations are controlled by the use of conventional PID and parameters which are adaptive to PID controllers. A parameters adaptive PID controller is designed to improve the passenger comfort by intuitional usage of this method that renews the parameters online and sensitively under variable track inputs. Sinusoidal vertical rail misalignment and measured real rail irregularity are considered as two different disruptive effects of the system. Active vibration control is applied to the system through the secondary suspension. The active suspension application of rail vehicle is examined by using 5-DOF quarter-rail vehicle model by using Manchester benchmark dynamic parameters. The new parameters of adaptive controller are optimized by means of genetic algorithm toolbox of MATLAB. Simulations are performed at maximum urban transportation speed (90 km/h of the rail vehicle with ±5% load changes of rail vehicle body to test the robustness of controllers. As a result, superior performance of parameters of adaptive controller is determined in time and frequency domain.

How to Park Freight Trains on Rail-Rail Transshipment Yards: The Train Location Problem

OpenAIRE

Michael Kellner; Nils Boysen; Malte Fliedner

2010-01-01

In modern rail-rail transshipment yards huge gantry cranes spanning all railway tracks allow for an efficent transshipment of containers between different freight trains. This way, multiple trains loaded with cargo for varying destinations can be consolidated to a reduced number of homogeneous trains, which is an essential requirement of hub-and-spoke railway systems. An important problem during the daily operations of such a transshipment yard is the train location problem, which assigns eac...

The physics of wheel-rail stability

Science.gov (United States)

Tan, B. T. G.

2018-05-01

This article discusses, at a simple level, the dynamics of the wheel-rail interface, which is fundamental to the stability of rail vehicles. The physics underlying this topic deserves to be better known by physicists and physics students, as it underpins such an important part of our technological infrastructure.

The Physics of Wheel-Rail Stability

Science.gov (United States)

Tan, B. T. G.

2018-01-01

This article discusses, at a simple level, the dynamics of the wheel-rail interface, which is fundamental to the stability of rail vehicles. The physics underlying this topic deserves to be better known by physicists and physics students, as it underpins such an important part of our technological infrastructure

Návrh Rail-to-Rail operačního zesilovače v technologii CMOS

OpenAIRE

Cvešper, Stanislav

2016-01-01

Práce se zabývá návrhem rail-to-rail operačního zesilovače ve třídě AB v technologii CMOS I3T25. Práce začíná úvodem do CMOS tranzistorů, následuje rozbor struktur operačního zesilovače, jeho návrh a simulace v návrhovém prostředí Cadence, popsány jsou také různé metody pro minimalizaci napěťové symetrie. Hlavním cílem práce je dosažení rail-to-rail vstupního i výstupního rozsahu operačního zesilovače pracujícího ve třídě AB, s minimální napěťovou nesymetrií, včetně návrhu topologie navrženéh...

49 CFR 174.59 - Marking and placarding of rail cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Marking and placarding of rail cars. 174.59... RAIL General Handling and Loading Requirements § 174.59 Marking and placarding of rail cars. No person may transport a rail car carrying hazardous materials unless it is marked and placarded as required by...

Finite element analysis of rail-wheel interaction

International Nuclear Information System (INIS)

Rahman, F.; Kharlamov, Y.A.; Islam, S.; Khan, A.A.

2006-01-01

Damage mechanisms such as surface cracks, plastic deformation and wear can significantly reduce the service life of railway track and rolling stock. They also have a negative impact on the rolling noise as well as: on the riding comfort. A proper understanding of these mechanisms requires a detailed knowledge of physical interaction between wheel and rail. Furthermore, demands for higher train speeds and increased axle loads implies that the consequences of larger contact. forces between wheel and rail must be thoroughly investigated. Two methods have traditionally been used to investigate the rail-wheel contact, that is the Hertz analytical method and simplified numerical method based on the boundary element (BE) method. These methods rely on a half-space assumption and a linear material model. This paper presents that to overcome these limitations, a tool for FE-based quasistatic wheel-rail contact simulations has been developed. The tool is a library of ANSYS macro routines for configuring, meshing and loading of a parametric wheel-rail model. The meshing is based on measured wheel and rail profiles. The wheel and rail materials in the contact region are treated as elastic-plastic with kinematic hardening. By controlling the values of the configuration parameters, representations of various driving cases can be generated. The quasi-static loads are obtained from train motion. Interaction phenomena such as rolling, spinning and sidling can be included. The modeling tool and a methodology are described in the presented paper. Significant differences in the calculated state between the FE solution and the traditional approaches can be observed. These differences are most significant in situations with flange contact. (author)

Annual Trauma Anesthesia and Critical Care Symposium (4th) Held in Baltimore, Maryland on May 2 - 5, 1991

Science.gov (United States)

1991-07-01

Attending Anesthesiologist The Shock Trauma Center, MIEMSS University of Maryland Medical System Editor, Chest Physiotherapy in the ICU Baltimore...D. Anticholinergic E, Anesthetic Adjuncts F. Guides to management VII. Potential Problems A. Pediatric patients B. Geriatric patients

The influence of friction coefficient and wheel/rail profiles on energy dissipation in the wheel/rail contact

NARCIS (Netherlands)

Idarraga Alarcon, G.A.; Burgelman, N.D.M.; Meza Meza, J.; Toro, A.; Li, Z.

2015-01-01

This work investigates the energy dissipation in a wheel/rail system through friction work modeling. In order to identify the effect of the friction coefficient on the energy dissipation in the wheel/rail contact, several simulations were performed using a 3D multibody model of a railway vehicle

A Big Data Analysis Approach for Rail Failure Risk Assessment.

Science.gov (United States)

Jamshidi, Ali; Faghih-Roohi, Shahrzad; Hajizadeh, Siamak; Núñez, Alfredo; Babuska, Robert; Dollevoet, Rolf; Li, Zili; De Schutter, Bart

2017-08-01

Railway infrastructure monitoring is a vital task to ensure rail transportation safety. A rail failure could result in not only a considerable impact on train delays and maintenance costs, but also on safety of passengers. In this article, the aim is to assess the risk of a rail failure by analyzing a type of rail surface defect called squats that are detected automatically among the huge number of records from video cameras. We propose an image processing approach for automatic detection of squats, especially severe types that are prone to rail breaks. We measure the visual length of the squats and use them to model the failure risk. For the assessment of the rail failure risk, we estimate the probability of rail failure based on the growth of squats. Moreover, we perform severity and crack growth analyses to consider the impact of rail traffic loads on defects in three different growth scenarios. The failure risk estimations are provided for several samples of squats with different crack growth lengths on a busy rail track of the Dutch railway network. The results illustrate the practicality and efficiency of the proposed approach. © 2017 The Authors Risk Analysis published by Wiley Periodicals, Inc. on behalf of Society for Risk Analysis.

Structural response of a rail acceleration

International Nuclear Information System (INIS)

Wang, S.Y.

1984-01-01

The transient response of a 0.4 by 0.6 cm rectangular bore rail accelerator was analyzed by a three dimensional finite element code. The copper rail deflected to a peak value of 0.08 mm in compression and then oscillated at an amplitude of 0.02 mm. Simultaneously the insulating side wall of glass fabric base, epoxy resin laminate (G-10) was compressed to a peak value of 0.13 mm and rebounded to a steady state in extension. Projectile pinch or blowby due to the rail extension or compression, respectively, can be identified by examining the time history of the rail displacement. The effect of blowby was most significant at the side wall characterized by mm size displacement in compression. Dynamic stress calculations indicate that the G-10 supporting material behind the rail is subjected to over 21 MPa at which the G-10 could fail if the laminate was not carefully oriented. Results for a polycarbonate resin (Lexan) side wall show much larger displacements and stresses than for G-10. The tradeoff between the transparency of Lexan and the mechanical strength of G-10 for sidewall material is obvious. Displacement calculations from the modal method are smaller than the results from the direct integration method by almost an order of magnitude, because the high frequency effect is neglected. 12 references

Guidance for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive material by rail. Pt. 5

International Nuclear Information System (INIS)

1996-01-01

This document, part of a series of guides for those concerned with the road or rail transportation of dangerous goods, provides detailed recommendations for consignors, rail operators and others involved in the packaging, labelling and carriage of radioactive materials by rail. It covers the relevant legislation and regulations on the carriage of such dangerous goods to assist those involved with compliance. (UK)

Plasma treatment of crane rails

Directory of Open Access Journals (Sweden)

Владислав Олександрович Мазур

2016-07-01

Full Text Available Crane operation results in wear and tear of rails and crane wheels. Renovation and efficiency of these details is therefore relevant. Modern technologies of wheels and rails restoration use surfacing or high-frequency currents treatment. Surface treatment with highly concentrated streams of energy- with a laser beam, plasma jet- is a promising direction.. It is proposed to increase the efficiency of crane rails by means of surface plasma treatment. The modes of treatment have been chosen.. Modelling of plasma jet thermal impact on a solid body of complex shape has been made. Plasma hardening regimes that meet the requirements of production have been defined. Structural transformation of the material in the crane rails on plasma treatment has been investigated. It has been concluded that for carbon and low alloy crane steels the plasma exposure zone is characterized by a high degree of hardened structure dispersion and higher hardness as compared to the hardness after high-frequency quenching. As this takes place phase transformations are both shift (in the upper zone of plasma influence and fluctuation (in the lower zone of the plasma. With high-speed plasma heating granular or lamellar pearlite mainly transforms into austenite. The level of service characteristics of hardened steel, which is achieved in this case is determined by the kinetics and completeness of pearlite → austenite transformation. For carbon and low alloy rail steels plasma hardening can replace bulk hardening, hardening by high-frequency currents, or surfacing. The modes for plasma treatment which make it possible to obtain a surface layer with a certain service characteristics have been defined

Revisiting the reasons for contact fatigue defects in rails

Directory of Open Access Journals (Sweden)

Darenskiy Alexander

2017-01-01

Full Text Available As it is known rail is one of the most significant elements of the whole railway construction. Operation under alternating loads from wheels of the rolling stock and different ambient temperatures lead to appearance and development of rail defects and damages. A great variety of operational factors (freight traffic density, axial loads, traffic speeds, track layout and profile as well as special features of manufacturing and thermal treatment of rails create certain difficulties while identifying reasons for defects and damages. The article deals with an attempt to estimate influence of track layout and lateral forces on appearance of defects and damages in rails on the base of long-term observations of rail operation in Kharkiv Metro. On the basis of the vehicle/track mathematical model which considers structural features of both rolling stock and permanent way in underground systems, the level of lateral forces in curves was calculated. The coefficients of correlation between the track curvature, the level of forces and the amount of defected rails removed were later obtained, that made it possible to determine the dominant factor which may lead to appearance and development of contact fatigue defects in rails laid in curves.

Operations Research Approaches to Asset Management in Freight Rail

DEFF Research Database (Denmark)

Gorman, Michael F.; Harrod, Steven

2011-01-01

This article describes operations research methodologies as they apply to asset management in freight rail. We describe state-of-the-art methods for locomotive, crew, railcar, line and yard planning and management. We conclude with emerging areas of research in rail.......This article describes operations research methodologies as they apply to asset management in freight rail. We describe state-of-the-art methods for locomotive, crew, railcar, line and yard planning and management. We conclude with emerging areas of research in rail....

Investigation of the stresses in rails : Secondary effects associated with the bending of a centrically loaded rail

NARCIS (Netherlands)

Kolvoort, A.J.; Woestenburg, T.

1982-01-01

The flexural behaviour of a rail under purely vertical load acting in the plane of symmetry is investigated in this paper. For this purpose a rail ofNP 46 standard section was subjected to experimental research with the aid of electrical resistance strain gauges in the Laboratory for Highway and

A CMOS rail-to-rail linear VI-converter

NARCIS (Netherlands)

Vervoort, P.P.; Vervoort, P.P.; Wassenaar, R.F.

1995-01-01

A linear CMOS VI-converter operating in strong inversion with a common-mode input range from the negative to the positive supply rail is presented. The circuit consists of three linear VI-converters based on the difference of squares principle. Two of these perform the actual V to I conversion,

Improving fatigue performance of rail thermite welds

Science.gov (United States)

Jezzini-Aouad, M.; Flahaut, P.; Hariri, S.; Winiar, L.

2010-06-01

Rail transport development offers economic and ecological interests. Nevertheless, it requires heavy investments in rolling material and infrastructure. To be competitive, this transportation means must rely on safe and reliable infrastructure, which requires optimization of all implemented techniques and structure. Rail thermite (or aluminothermic) welding is widely used within the railway industry for in-track welding during re-rail and defect replacement. The process provides numerous advantages against other welding technology commonly used. Obviously, future demands on train traffic are heavier axle loads, higher train speeds and increased traffic density. Thus, a new enhanced weld should be developed to prevent accidents due to fracture of welds and to lower maintenance costs. In order to improve such assembly process, a detailed metallurgical study coupled to a thermomechanical modelling of the phenomena involved in the thermite welding process is carried out. Obtained data enables us to develop a new improved thermite weld (type A). This joint is made by modifying the routinely specified procedure (type B) used in a railway rail by a standard gap alumino-thermic weld. Joints of type A and B are tested and compared. Based on experimental temperature measurements, a finite element analysis is used to calculate the thermal residual stresses induced. In the vicinity of the weld, the residual stress patterns depend on the thermal conditions during welding as it also shown by litterature [1, 2]. In parallel, X-Ray diffraction has been used to map the residual stress field that is generated in welded rail of types A and B. Their effect on fatigue crack growth in rail welds is studied. An experimental study based on fatigue tests of rails welded by conventional and improved processes adjudicates on the new advances and results will be shown.

Segmented rail linear induction motor

Science.gov (United States)

Cowan, Jr., Maynard; Marder, Barry M.

1996-01-01

A segmented rail linear induction motor has a segmented rail consisting of a plurality of nonferrous electrically conductive segments aligned along a guideway. The motor further includes a carriage including at least one pair of opposed coils fastened to the carriage for moving the carriage. A power source applies an electric current to the coils to induce currents in the conductive surfaces to repel the coils from adjacent edges of the conductive surfaces.

Light Rails to Sustainable Mobility?

DEFF Research Database (Denmark)

Olesen, Mette

that there is not one overall rationale for implementing light rail, many arguments are evident in various contexts. Furthermore, findings in this paper show that planners, policy makers and other stakeholders shape stories for or against the implementation of light rail through the use of narratives that are linked...... infrastructure projects and urban interventions through the political process and secure the outcome of these projects are recognisable in proportion to the visionary concept....

The literature of the California black rail

Science.gov (United States)

Wilbur, Sanford R.

1974-01-01

Few birds have remained so little known as the California black rail (Laterallus jamaicensis coturniculus). Although first collected in 1859 or before and reported in 1874 (Ridgway 1874), its life history, distribution, and status have remained so obscure that even a sight record of the bird is deemed worthy of a report in some ornithological publications. Because degradation and loss of freshwater and saltwater marshlands in California may be detrimentally affecting the black rail, both the U.S. Bureau of Sport Fisheries and Wildlife (1973) and the California Department of Fish and Game (1972) have classified it as rare and worthy of further study. The 84 papers and notes both summarized in this report and included in its bibliography include essentially all that is currently known about the California black rail. Only 11 of these papers consider the life history of this rail in any detail. The rest are distribution notes and some of the more important papers on the closely related eastern black rail (L. j. jamaicensis). The latter are included for comparative purposes, or because they may lend clues to currently unknown facets of the life history of the western race.

Three-dimensional rail cooling analysis for a repetitively fired railgun

International Nuclear Information System (INIS)

Liu, H.P.

1991-01-01

This paper reports on a three-dimensional (3-D) rail cooling analysis for fabrication and demonstration of a stand-alone repetitive fire compulsator driven 9 MJ gun system which has been performed to assure the entire rail can be maintained below its thermal limit for multiple shots. The 3-D rail thermal model can predict the temperature, pressure, and convective heat transfer coefficient variations of the coolant along the 10 m long copper rail. The 9-MJ projectiles will be fired every 20 s for 3 min. Water cooling was used in the model for its high cooling capacity. Single liquid phase heat transfer was assumed in the cooling analysis. For multiple shots, the temperature difference between the rail and the water was enhanced due to accumulated heat in the rail. As a result, the heat removal by water increased from shot-to-shot. The rail temperature initially increased and finally stabilized after a number of shots

Rail inspection system based on iGPS

Science.gov (United States)

Fu, Xiaoyan; Wang, Mulan; Wen, Xiuping

2018-05-01

Track parameters include gauge, super elevation, cross level and so on, which could be calculated through the three-dimensional coordinates of the track. The rail inspection system based on iGPS (indoor/infrared GPS) was composed of base station, receiver, rail inspection frame, wireless communication unit, display and control unit and data processing unit. With the continuous movement of the inspection frame, the system could accurately inspect the coordinates of rail; realize the intelligent detection and precision measurement. According to principle of angle intersection measurement, the inspection model was structured, and detection process was given.

Relationships between pediatric asthma and socioeconomic/urban variables in Baltimore, Maryland

Science.gov (United States)

Kimes, Daniel; Ullah, Asad; Levine, Elissa; Nelson, Ross; Timmins, Sidey; Weiss, Sheila; Bollinger, Mary E.; Blaisdell, Carol

2004-01-01

Spatial relationships between clinical data for pediatric asthmatics (hospital and emergency department utilization rates), and socioeconomic and urban characteristics in Baltimore City were analyzed with the aim of identifying factors that contribute to increased asthma rates. Socioeconomic variables and urban characteristics derived from satellite data explained 95% of the spatial variation in hospital rates. The proportion of families headed by a single female was the most important variable accounting for 89% of the spatial variation. Evidence suggests that the high rates of hospital admissions and emergency department (ED) visits may partially be due to the difficulty of single parents with limited resources managing their child's asthma condition properly. This knowledge can be used for education towards mitigating ED and hospital events in Baltimore City.

Tunnel magnetoresistance in alumina, magnesia and composite tunnel barrier magnetic tunnel junctions

International Nuclear Information System (INIS)

Schebaum, Oliver; Drewello, Volker; Auge, Alexander; Reiss, Guenter; Muenzenberg, Markus; Schuhmann, Henning; Seibt, Michael; Thomas, Andy

2011-01-01

Using magnetron sputtering, we have prepared Co-Fe-B/tunnel barrier/Co-Fe-B magnetic tunnel junctions with tunnel barriers consisting of alumina, magnesia, and magnesia-alumina bilayer systems. The highest tunnel magnetoresistance ratios we found were 73% for alumina and 323% for magnesia-based tunnel junctions. Additionally, tunnel junctions with a unified layer stack were prepared for the three different barriers. In these systems, the tunnel magnetoresistance ratios at optimum annealing temperatures were found to be 65% for alumina, 173% for magnesia, and 78% for the composite tunnel barriers. The similar tunnel magnetoresistance ratios of the tunnel junctions containing alumina provide evidence that coherent tunneling is suppressed by the alumina layer in the composite tunnel barrier. - Research highlights: → Transport properties of Co-Fe-B/tunnel barrier/Co-Fe-B magnetic tunnel junctions. → Tunnel barrier consists of MgO, Al-Ox, or MgO/Al-Ox bilayer systems. → Limitation of TMR-ratio in composite barrier tunnel junctions to Al-Ox values. → Limitation indicates that Al-Ox layer is causing incoherent tunneling.

49 CFR 213.113 - Defective rails.

Science.gov (United States)

2010-10-01

... smooth, bright, or dark, round or oval surface substantially at a right angle to the length of the rail... in the head of the rail as a smooth, bright, or dark surface progressing until substantially at a... head, and extending into or through it. A crack or rust streak may show under the head close to the web...

Attractive Mobile Corridors - The Power of Light Rail Infrastructures

DEFF Research Database (Denmark)

Olesen, Mette; Lassen, Claus

2013-01-01

Light rail is a popular tool in urban development strategies in many European cities. One argument for choosing a rail-based solution is that it signals stability to investors and will attract development and investments in the corridor. The choice of corridor in the various light rail cities...... and redistributes urban space. Furthermore light rail is not only a physical infrastructure but also an infrastructure of power that is carefully planned and designed creating both mental and physical patterns of mobilities and immobilities. Hence it is important to underline that mobility systems, such as light...

Barriers to and enablers for European rail freight transport for integrated door-to-door logistics service. Part 2: Enablers for multimodal rail freight transport

Directory of Open Access Journals (Sweden)

Dewan Md Zahurul ISLAM

2014-12-01

Full Text Available The objective of this paper is to examine and identify barriers to and enablers for the European rail freight transport services as a transport chain partner along the supply chains in the changing market scenario. The changing market scenario includes, among others, requiring 'door-to-door' rather than 'terminal to terminal' and integrated service, competitive ability to attract non-rail cargo type, changes in the customer requirements (e.g. reliable service and changes in the operational requirements and practices. Using a literature review method, the paper is presented in two parts. The part 1 focuses on the identification of barriers to the European rail freight service by reviewing freight logistics services for global supply chains followed by the current performance of European rail freight transport followed by a discussion on the rail freight market liberalisation in Europe. Then rail freight transport in the Unites States (U.S. is discussed. The research notes that although the background, scope and necessity for reform measures in Europe differ from those of the U.S., some lessons can be learned and the main lesson is that an appropriate reform measure can enhance rail sector competitive ability in Europe. The part 2 of the paper is dedicated to recommend some concrete steps and actions as enablers to remove the barriers identified in the part 1 to develop multimodal rail freight transport. The enablers for multimodal rail freight transport include: •\tEuropean rail freight transport market needs full liberalisation so that incumbent and new entrants can compete freely. •\tThe rail operators need to acquire service (e.g. customer tailored services, door to door service quality offered by road freight operators. •\tThey need to conduct a combination of ‘terminal-to-terminal’ and door-to-door operations, as and when needed; •\tThey must build partnership with freight forwarder or 3PLs to include all types of customers

Method for Predicting Thermal Buckling in Rails

Science.gov (United States)

2018-01-01

A method is proposed herein for predicting the onset of thermal buckling in rails in such a way as to provide a means of avoiding this type of potentially devastating failure. The method consists of the development of a thermomechanical model of rail...

Rail for inspection/maintenance device in TOKAMAK type container of a thermonuclear reactor

International Nuclear Information System (INIS)

Takahashi, Kenji.

1996-01-01

A circular rail divided into four arcuate parts for an inspection/maintenance device which runs in a TOKAMAK type container is disposed. Each of the divided rails is supported at the center of the outer surface rotatably by extendable rail supporting shafts. Each of the divided rail is constituted such that it can be contained between limiters disposed at the outer side of the TOKAMAK container when each of the rail support shafts is contracted. With such a constitution, each of the rail support shafts and arcuate rail is contracted and rotated from the outside of the TOKAMAK type container by an actuator. In order to form a circular rail, each of the rail support shafts is extended toward the center of the TOKAMAK type container, and then each of the arcuate rails is rotated into a horizontal state. Then, the joint portions of each of the arcuate rails are connected by using remote controllable locking rods. (I.S.)

49 CFR 38.175 - High-speed rail cars, monorails and systems.

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false High-speed rail cars, monorails and systems. 38....175 High-speed rail cars, monorails and systems. (a) All cars for high-speed rail systems, including... monorail systems operating primarily on dedicated rail (i.e., not used by freight trains) or guideway, in...

Field homogeneity improvement of maglev NdFeB magnetic rails from joints.

Science.gov (United States)

Li, Y J; Dai, Q; Deng, C Y; Sun, R X; Zheng, J; Chen, Z; Sun, Y; Wang, H; Yuan, Z D; Fang, C; Deng, Z G

2016-01-01

An ideal magnetic rail should provide a homogeneous magnetic field along the longitudinal direction to guarantee the reliable friction-free operation of high temperature superconducting (HTS) maglev vehicles. But in reality, magnetic field inhomogeneity may occur due to lots of reasons; the joint gap is the most direct one. Joint gaps inevitably exist between adjacent segments and influence the longitudinal magnetic field homogeneity above the rail since any magnetic rails are consisting of many permanent magnet segments. To improve the running performance of maglev systems, two new rail joints are proposed based on the normal rail joint, which are named as mitered rail joint and overlapped rail joint. It is found that the overlapped rail joint has a better effect to provide a competitive homogeneous magnetic field. And the further structure optimization has been done to ensure maglev vehicle operation as stable as possible when passing through those joint gaps. The results show that the overlapped rail joint with optimal parameters can significantly reduce the magnetic field inhomogeneity comparing with the other two rail joints. In addition, an appropriate gap was suggested when balancing the thermal expansion of magnets and homogenous magnetic field, which is considered valuable references for the future design of the magnetic rails.

Do Urban Rail Transit Facilities Affect Housing Prices? Evidence from China

Directory of Open Access Journals (Sweden)

Xu Zhang

2016-04-01

Full Text Available Urban rail transit facilities play a critical role in citizen’s social activities (e.g., residence, work and education. Using panel data on housing prices and urban rail transit facilities for 35 Chinese cities for 2002 to 2013, this study constructs a panel data model to evaluate the effect of rail transit facilities on housing prices quantitatively. A correlation test reveals significant correlations between housing prices and rail transit facilities. Empirical results demonstrate that rail transit facilities can markedly elevate real estate prices. Quantitatively, a 1% increase in rail transit mileage improves housing prices by 0.0233%. The results highlight the importance of other factors (e.g., per capita GDP, land price, investment in real estate and population density in determining housing prices. We also assess the effects of expectations of new rail transit lines on housing prices, and the results show that expectation effects are insignificant. These findings encourage Chinese policy makers to take rail transit facilities into account in achieving sustainable development of real estate markets.

Buckling analysis of continuous welded rail track

NARCIS (Netherlands)

Van, M.A.

1996-01-01

Continuous welded rail track, compared to jointed track not only reduces maintenance costs, but also increases life time of track components and the comfort of passengers. Since expansion of the rails is hardly possible in CWR-track, a temperature increase will result in high compressive stresses

75 FR 16552 - High-Speed Intercity Passenger Rail (HSIPR) Program

Science.gov (United States)

2010-04-01

...; Enhancing intercity travel options; Ensuring a state of good repair of key intercity passenger rail assets... DEPARTMENT OF TRANSPORTATION Federal Railroad Administration High-Speed Intercity Passenger Rail... selections for the High-Speed Intercity Passenger Rail (HSIPR) Program. This notice builds on the program...

A novel permanent magnetic rail for HTS levitation propulsion system

International Nuclear Information System (INIS)

Guo, F.; Tang, Y.; Ren, L.; Li, J.

2009-01-01

The Halbach Array has a characteristic advantage that the spatial fundamental field is canceled on one side of the array while the field intensity on the other side is enhanced. So this array could be used in the design of high temperature superconducting permanent magnetic levitation rail to improve the surface magnetic field and levitation force. This paper compared the surface magnetic field of the Halbach Array rail and two conventional levitation rails at first. Then proposed the potential advantages of Halbach Array applied in permanent magnetic rail system. But the Halbach Array rail is mechanical instability. An novel improved Halbach Array rail is proposed in this paper. The new structure combined the advantages of traditional structure and Halbach Array structure, solved the problem of mechanical instability, and carried on the advantage of Halbach Array on the magnetic field distribution at the same time.

75 FR 30747 - Drawbridge Operation Regulation; Curtis Creek, Baltimore, MD

Science.gov (United States)

2010-06-02

... remote location at the City of Baltimore Transportation Management Center. This proposed change would... viewing or submitting material to the docket, call Renee V. Wright, Program Manager, Docket Operations... rule based on your comments. Viewing Comments and Documents To view comments, as well as documents...

Field monitoring of rail squats using 3D ultrasonic mapping technique

International Nuclear Information System (INIS)

Kaewunruen, S.; Ishida, M.

2014-01-01

Rail squats and studs are typically classified as the propagation of any cracks .that have grown longitudinally through the subsurface. Some of the cracks could propagate to the bottom of rails transversely, which have branched from the initial longitudinal cracks with a depression of rail surface. The rail defects are commonly referred to as 'squats' when they were initiated from a damage layer caused by rolling contact fatigue, and as 'studs' when they were associated with a white etching layer caused by the transformation from pearlitic steel due to friction heat generated by wheel sliding or excessive traction. Such above-mentioned rail defects have been often observed in railway tracks catered for either light passenger or heavy freight traffics and for low, medium or high speed trains all over the world for over 60 years except some places such as sharp curves where large wear takes place under severe friction between the wheel flange and rail gauge face. It becomes a much-more significant issue when the crack grows and sometimes flakes off the rail (by itself or by insufficient rail grinding), resulting in a rail surface irregularity. Such rail surface defects induce wheel/rail impact and large amplitude vibration of track structure and poor ride quality. In Australia, Europe, and Japan, rail squats/studs have occasionally turned into broken rails. The root cause and preventive solution to this defect are still under investigation from the fracture mechanics and material sciences point of view. Some patterns of squat/stud development related to both curve and tangent track geometries have been observed and squat growth has been monitored for individual squats using ultrasonic mapping techniques. This paper highlights the field monitoring of squat/stud distribution and its growth. Squat/stud growth has been detected and scanned using the ultrasonic measurement device on a grid applied to the rail surface. The depths of crack paths at each grid node form a

Field monitoring of rail squats using 3D ultrasonic mapping technique

Energy Technology Data Exchange (ETDEWEB)

Kaewunruen, S., E-mail: sakdirat.kaewunruen@transport.nsw.gov.au [NSW, Transport, Sydney (Australia); Ishida, M., E-mail: ishida-mk@n-koei.jp [Nippon Koei Co. Ltd., Railway Div., Railway Engineering Dept., Chiyoda-ku, Tokyo (Japan)

2014-11-15

Rail squats and studs are typically classified as the propagation of any cracks .that have grown longitudinally through the subsurface. Some of the cracks could propagate to the bottom of rails transversely, which have branched from the initial longitudinal cracks with a depression of rail surface. The rail defects are commonly referred to as 'squats' when they were initiated from a damage layer caused by rolling contact fatigue, and as 'studs' when they were associated with a white etching layer caused by the transformation from pearlitic steel due to friction heat generated by wheel sliding or excessive traction. Such above-mentioned rail defects have been often observed in railway tracks catered for either light passenger or heavy freight traffics and for low, medium or high speed trains all over the world for over 60 years except some places such as sharp curves where large wear takes place under severe friction between the wheel flange and rail gauge face. It becomes a much-more significant issue when the crack grows and sometimes flakes off the rail (by itself or by insufficient rail grinding), resulting in a rail surface irregularity. Such rail surface defects induce wheel/rail impact and large amplitude vibration of track structure and poor ride quality. In Australia, Europe, and Japan, rail squats/studs have occasionally turned into broken rails. The root cause and preventive solution to this defect are still under investigation from the fracture mechanics and material sciences point of view. Some patterns of squat/stud development related to both curve and tangent track geometries have been observed and squat growth has been monitored for individual squats using ultrasonic mapping techniques. This paper highlights the field monitoring of squat/stud distribution and its growth. Squat/stud growth has been detected and scanned using the ultrasonic measurement device on a grid applied to the rail surface. The depths of crack paths at each

Mock-up tests of rail-mounted vehicle type in-vessel transporter/manipulator

International Nuclear Information System (INIS)

Oka, K.; Kakaudate, S.; Fukatsu, S.

1995-01-01

A rail-mounted vehicle system has been developed for remote maintenance of in-vessel components for fusion experimental reactor. In this system, a rail deploying/storing system is installed at outside of the reactor core and used to deploy a rail transporter and vehicle/manipulator for the in-vessel maintenance. A prototype of the rail deploying/storing system has been fabricated for mockup tests. This paper describes structural design of the prototypical rail deploying/storing system and results of the performance tests such as payload capacity, position control and rail deployment/storage performance

Ten years of common-rail injection systems for passenger cars; Gemeine Drucksache. Zehn Jahre Common-Rail-Einspritzsystem fuer Pkw

Energy Technology Data Exchange (ETDEWEB)

Hohenthal, M.Y. von

2007-07-15

The future of the diesel engine started in 1997 with the Bosch common rail injection system which provided higher power, higher rotary momentum, lower consumption, lower noise and lower pollutant emissions. Since then, high-pressure common-rail injection systems have become state of the art. (orig.)

Barriers to and enablers for European rail freight transport for integrated door-to-door logistics service. Part 1: Barriers to multimodal rail freight transport

Directory of Open Access Journals (Sweden)

Dewan Md Zahurul ISLAM

2014-09-01

Full Text Available The objective of this paper is to examine and identify barriers to and enablers for the European rail freight transport services as a transport chain partner along the supply chains in the changing market scenario. The changing market scenario includes, among others, requiring 'door-to-door' rather than 'terminal to terminal' and integrated service, competitive ability to attract non-rail cargo type, changes in the customer requirements (e.g. reliable service and changes in the operational requirements and practices. Using a literature review method, the paper is presented in two parts. The part 1 focuses on the identification of barriers to the European rail freight service by reviewing freight logistics services for global supply chains followed by the current performance of European rail freight transport followed by a discussion on the rail freight market liberalisation in Europe. Then rail freight transport in the Unites States (U.S. is discussed. The research notes that although the background, scope and necessity for reform measures in Europe differ from those of the U.S., some lessons can be learned and the main lesson is that an appropriate reform measure can enhance rail sector competitive ability in Europe. Examining and identifying the barriers in the part 1 (with the pan-Pacific examples of rail freight transports, the part 2 of the paper focuses on recommending clear actions and steps as enablers for the rail freight industry in general and operators in particular. The research in part 1 of the paper finds that: •\tIn many European countries, the rail freight market is not fully liberalised. In such market segment, infrastructure managers do act independently for incumbents and new entrant operators that hamper the progress of building a competitive market; •\tThe rail operators have not yet achieved the service quality (e.g. customer tailored service needed for the modern supply chains; •\tThey operate �

A 0.8V, 7μA, rail-to-rail input/output, constant Gm operational amplifier in standard digital 0.18μm CMOS

OpenAIRE

Citakovic, J; Nielsen, I. Riis; Nielsen, Jannik Hammel; Asbeck, P; Andreani, Pietro

2005-01-01

A two-stage amplifier, operational at 0.8V and drawing 7μA, has been integrated in a standard digital 0.18μm CMOS process. Rail-to-rail operations at the input are enabled by complementary transistor pairs with gm control. The efficient rail-to-rail output stage is biased in class AB. The measured DC gain of the amplifier is 75dB, and the unity-gain frequency is 870kHz with a 12pF, 100kΩload. Both input and output stage transistors are biased in weak inversion.

Sound Quality Evaluation and Optimization for Interior Noise of Rail Vehicle

Directory of Open Access Journals (Sweden)

Kai Hu

2014-08-01

Full Text Available A procedure for sound filed simulation, sound quality (SQ evaluation, and optimization of interior noise of a rail vehicle is investigated in this paper. Firstly, some interior noises are measured on site when the subway is running in tunnel at a speed of 60 km/h. The sound pressure levels (SPLs, loudness, sharpness, and roughness of the measured noise are analyzed. A finite element model for acoustical simulation of the carriage is established by using the Actran software. The accuracy and feasibility of the finite model are verified by comparing the psychoacoustical parameters from the simulations and measurements. By using orthogonal experimental design, finally, the best optimization scheme is put forward, which obtained a sound quality improvement with a 4.81 dB decrease in SPL and a 1.07 sone reduction in loudness. The proposed optimization scheme may be extended to other vehicles for improving interior acoustic environment.

Simulations of roughness initiation and growth on railway rails

Science.gov (United States)

Sheng, X.; Thompson, D. J.; Jones, C. J. C.; Xie, G.; Iwnicki, S. D.; Allen, P.; Hsu, S. S.

2006-06-01

A model for the prediction of the initiation and growth of roughness on the rail is presented. The vertical interaction between a train and the track is calculated as a time history for single or multiple wheels moving on periodically supported rails, using a wavenumber-based approach. This vertical dynamic wheel/rail force arises from the varying stiffness due to discrete supports (i.e. parametric excitation) and the roughness excitation on the railhead. The tangential contact problem between the wheel and rail is modelled using an unsteady two-dimensional approach and also using the three-dimensional contact model, FASTSIM. This enables the slip and stick regions in the contact patch to be identified from the input geometry and creepage between the wheel and rail. The long-term wear growth is then predicted by applying repeated passages of the vehicle wheelsets, as part of an iterative solution.

Prototype Rail Crossing Violation Warning Application Project Report.

Science.gov (United States)

2017-09-05

This report is the Project Report for the Rail Crossing Violation Warning (RCVW) safety application developed for the project on Rail Crossing Violation Warning Application and Infrastructure Connection, providing a means for equipped connected vehic...

77 FR 17121 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-03-23

... decision may be purchased by contacting the Office of Public Assistance, Governmental Affairs, and...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, Department of Transportation. ACTION: Approval of rail cost adjustment factor. [[Page 17122

Multiphysics modeling of a rail gun launcher

Directory of Open Access Journals (Sweden)

Y W Kwon

2016-03-01

Full Text Available A finite element based multiphysics modeling was conducted for a rail gunlauncher to predict the exit velocity of the launch object, and temperaturedistribution. For this modeling, electromagnetic field analysis, heat transferanalysis, thermal stress analysis, and dynamic analysis were conducted fora system consisting of two parallel rails and a moving armature. In particular,an emphasis was given to model the contact interface between rails andthe armature. A contact theory was used to estimate the electric as well asthermal conductivities at the interface. Using the developed model, aparametric study was conducted to understand effects of variousparameters on the exit velocity as well as the temperature distribution in therail gun launcher.

Electric rail gun application to space propulsion

International Nuclear Information System (INIS)

Barber, J.P.

1979-01-01

The paper examines the possibility of using the DC electric gun principles as a space vehicle propulsion system, capable of producing intermediate thrust levels. The application of an electromagnetic launch technique, called the DC electric rail gun, to the space propulsion concept of O'Neill, is examined. It is determined that the DC electric rail gun offers very high projectile accelerations and a very significant potential for reducing the size and mass of a reaction motor for space application. A detailed description of rail gun principles is given and some simple expressions for the accelerating force, gun impedance, power supply requirements, and system performance are discussed

30 CFR 57.9102 - Movement of independently operating rail equipment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Movement of independently operating rail... NONMETAL MINES Loading, Hauling, and Dumping Traffic Safety § 57.9102 Movement of independently operating rail equipment. Movement of two or more pieces of rail equipment operating independently on the same...

The Beginner's Guide to Wind Tunnels with TunnelSim and TunnelSys

Science.gov (United States)

Benson, Thomas J.; Galica, Carol A.; Vila, Anthony J.

2010-01-01

The Beginner's Guide to Wind Tunnels is a Web-based, on-line textbook that explains and demonstrates the history, physics, and mathematics involved with wind tunnels and wind tunnel testing. The Web site contains several interactive computer programs to demonstrate scientific principles. TunnelSim is an interactive, educational computer program that demonstrates basic wind tunnel design and operation. TunnelSim is a Java (Sun Microsystems Inc.) applet that solves the continuity and Bernoulli equations to determine the velocity and pressure throughout a tunnel design. TunnelSys is a group of Java applications that mimic wind tunnel testing techniques. Using TunnelSys, a team of students designs, tests, and post-processes the data for a virtual, low speed, and aircraft wing.

Community Resources for Career Education: Starring Baltimore's McCormick Plan

Science.gov (United States)

Carey, E. Niel; Marshall, Howard E.

1973-01-01

The article develops from a general discussion of the utilization of community resources in career education to a discussion of a particular program--the McCormick Plan in Baltimore--and other Maryland programs. Suggestions drawn from those programs are offered for identifying and using such resources. (AG)

A systems approach to reduce urban rail energy consumption

International Nuclear Information System (INIS)

González-Gil, A.; Palacin, R.; Batty, P.; Powell, J.P.

2014-01-01

Highlights: • An insightful overview of energy usage in urban rail systems is given. • The principal measures to reduce urban rail energy consumption are appraised. • A methodology is proposed to help implement energy saving schemes in urban rail. • Regenerative braking is shown to offer the greatest energy saving potential. - Abstract: There is increasing interest in the potential of urban rail to reduce the impact of metropolitan transportation due to its high capacity, reliability and absence of local emissions. However, in a context characterised by increasing capacity demands and rising energy costs, and where other transport modes are considerably improving their environmental performance, urban rail must minimise its energy use without affecting its service quality. Urban rail energy consumption is defined by a wide range of interdependent factors; therefore, a system wide perspective is required, rather than focusing on energy savings at subsystem level. This paper contributes to the current literature by proposing an holistic approach to reduce the overall energy consumption of urban rail. Firstly, a general description of this transport mode is given, which includes an assessment of its typical energy breakdown. Secondly, a comprehensive appraisal of the main practices, strategies and technologies currently available to minimise its energy use is provided. These comprise: regenerative braking, energy-efficient driving, traction losses reduction, comfort functions optimisation, energy metering, smart power management and renewable energy micro-generation. Finally, a clear, logical methodology is described to optimally define and implement energy saving schemes in urban rail systems. This includes general guidelines for a qualitative assessment and comparison of measures alongside a discussion on the principal interdependences between them. As a hypothetical example of application, the paper concludes that the energy consumption in existing urban

Singular point analysis during rail deployment into vacuum vessel for ITER blanket maintenance

International Nuclear Information System (INIS)

Kakudate, Satoshi; Shibanuma, Kiyoshi

2007-05-01

Remote maintenance of the ITER blanket composed of about 400 modules in the vessel is required by a maintenance robot due to high gamma radiation of ∼500Gy/h in the vessel. A concept of rail-mounted vehicle manipulator system has been developed to apply to the maintenance of the ITER blanket. The most critical issue of the vehicle manipulator system is the feasibility of the deployment of the articulated rail composed of eight rail links into the donut-shaped vessel without any driving mechanism in the rail. To solve this issue, a new driving mechanism and procedure for the rail deployment has been proposed, taking account of a repeated operation of the multi-rail links deployed in the same kinematical manner. The new driving mechanism, which is deferent from those of a usual 'articulated arm' equipped with actuator in the every joint for movement, is composed of three mechanisms. To assess the feasibility of the kinematics of the articulated rail for rail deployment, a kinematical model composed of three rail links related to a cycle of the repeated operation for rail deployment was considered. The determinant det J' of the Jacobian matrix J' was solved so as to estimate the existence of a singular point of the transformation during rail deployment. As a result, it is found that there is a singular point due to det J'=0. To avoid the singular point of the rail links, a new location of the second driving mechanism and the related rail deployment procedure are proposed. As a result of the rail deployment test based on the new proposal using a full-scale vehicle manipulator system, the respective rail links have been successfully deployed within 6 h less than the target of 8 h in the same manner of the repeated operation under a synchronized cooperation among the three driving mechanisms. It is therefore concluded that the feasibility of the rail deployment of the articulated rail composed of simple structures without any driving mechanism has been demonstrated

30 CFR 56.9102 - Movement of independently operating rail equipment.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Movement of independently operating rail... MINES Loading, Hauling, and Dumping Traffic Safety § 56.9102 Movement of independently operating rail equipment. Movement of two or more pieces of rail equipment operating independently on the same track shall...

An automated system for rail transit infrastructure inspection.

Science.gov (United States)

2015-03-01

This project applied commercial remote sensing and spatial information (CRS&SI) : technologies such as Ground Penetrating Radar (GPR), laser, GIS, and GPS to passenger rail : inspections. An integrated rail inspection system that can be mounted on hi...

EVALUATION OF STRAIN-STRESS STATE OF THE RAILS IN THE PRODUCTION

Directory of Open Access Journals (Sweden)

V. V. Muravev

2017-01-01

Full Text Available High values of residual stresses is one of the most common reason of breaking lots of metal constructions, including rails. These stresses can reach values of flow limit, especially in the area of faults. Estimation of residual stresses values allows to get information about technical condition of the rail and also allow to avoid abnormal situations So, the aim of the research is creating the model of stress-strain state of the rail, which was hardened in its top and bottom, and to compare modeling results with experimental measurements of stresses and discrepancy of the housing.For creating the model and making evaluations by finite element method we used a program COMSOL. Forces on the top and bottom of the rail cause tension stresses, forces on the web of the rail cause tensile stresses. We compared calculated values of stresses with discrepancy of the housing. The discrepancy of the housing is informative characteristic for estimating the residual stresses according to standards. For experimental measurements we used an acoustic structuroscope SEMA. This structuroscope uses the acoustoelastic phenomenon for measurements. We made measurements of the five rails.According to the calculation results of the model, critical discrepancy of the housing in 2 mm corresponded to the following values of maximum stresses: –54 MPa in the top of the rail, 86 MPa in the web and –62 MPa in the bottom of the rail. Experimental measurements are the following: from –48 MPa to – 64 MPa in the top of the rail, 54 MPa to 93 MPa in the web of the rail, and –59 MPA to –74 MPa in the bottom of the rail. Absolute error was ±5 MPa.Thus we created the model, which allowed to analyze strain-stress state and compare real values of stresses with discrepancy of the housing. Results of the modeling showed coincidence with structure of distribution of residual stresses in five probes of rails. 

Rail renaissance based on strategic market segmentation principles

African Journals Online (AJOL)

rail renaissance, market segmentation, South Africa, state of logistics, ... The modal imbalance is the result of a historical rail investment backlog, with ..... vector that can be thought of as a chromosome in genetic terms, while the values used.

Optimal Placement Method of RFID Readers in Industrial Rail Transport for Uneven Rail Traflc Volume Management

Science.gov (United States)

Rakhmangulov, Aleksandr; Muravev, Dmitri; Mishkurov, Pavel

2016-11-01

The issue of operative data reception on location and movement of railcars is significant the constantly growing requirements of the provision of timely and safe transportation. The technical solution for efficiency improvement of data collection on rail rolling stock is the implementation of an identification system. Nowadays, there are several such systems, distinguished in working principle. In the authors' opinion, the most promising for rail transportation is the RFID technology, proposing the equipping of the railway tracks by the stationary points of data reading (RFID readers) from the onboard sensors on the railcars. However, regardless of a specific type and manufacturer of these systems, their implementation is affiliated with the significant financing costs for large, industrial, rail transport systems, owning the extensive network of special railway tracks with a large number of stations and loading areas. To reduce the investment costs for creation, the identification system of rolling stock on the special railway tracks of industrial enterprises has developed the method based on the idea of priority installation of the RFID readers on railway hauls, where rail traffic volumes are uneven in structure and power, parameters of which is difficult or impossible to predict on the basis of existing data in an information system. To select the optimal locations of RFID readers, the mathematical model of the staged installation of such readers has developed depending on the non-uniformity value of rail traffic volumes, passing through the specific railway hauls. As a result of that approach, installation of the numerous RFID readers at all station tracks and loading areas of industrial railway stations might be not necessary,which reduces the total cost of the rolling stock identification and the implementation of the method for optimal management of transportation process.

Youth Apprenticeship: A Hopeful Approach for Improving Outcomes for Baltimore Youth. The Abell Report. Volume 28, No. 2

Science.gov (United States)

Lerman, Robert I.; Packer, Arnold

2015-01-01

Youth transitions to rewarding careers remain a critical problem for America's current and future workforce. In Baltimore, where only one in five graduates of Baltimore City Public Schools matriculates to a four-year college and the unemployment rate for 16 to 19 year-olds is over 40 percent, opportunities to gain meaningful training and work…

A big data analysis approach for rail failure risk assessment

NARCIS (Netherlands)

Jamshidi, A.; Faghih Roohi, S.; Hajizadeh, S.; Nunez Vicencio, Alfredo; Babuska, R.; Dollevoet, R.P.B.J.; Li, Z.; De Schutter, B.H.K.

2017-01-01

Railway infrastructure monitoring is a vital task to ensure rail transportation safety. A rail failure could result in not only a considerable impact on train delays and maintenance costs, but also on safety of passengers. In this article, the aim is to assess the risk of a rail failure by

Structural parameter optimization design for Halbach permanent maglev rail

International Nuclear Information System (INIS)

Guo, F.; Tang, Y.; Ren, L.; Li, J.

2010-01-01

Maglev rail is an important part of the magnetic levitation launch system. Reducing the manufacturing cost of magnetic levitation rail is the key problem for the development of magnetic levitation launch system. The Halbach permanent array has an advantage that the fundamental spatial field is cancelled on one side of the array while the field on the other side is enhanced. So this array used in the design of high temperature superconducting permanent maglev rail could improve the surface magnetic field and the levitation force. In order to make the best use of Nd-Fe-B (NdFeB) material and reduce the cost of maglev rail, the effect of the rail's structural parameters on levitation force and the utilization rate of NdFeB material are analyzed. The optimal ranges of these structural parameters are obtained. The mutual impact of these parameters is also discussed. The optimization method of these structure parameters is proposed at the end of this paper.

Structural parameter optimization design for Halbach permanent maglev rail

Energy Technology Data Exchange (ETDEWEB)

Guo, F., E-mail: guofang19830119@163.co [R and D Center of Applied Superconductivity, Huazhong University of Science and Technology, Wuhan 430074 (China); Tang, Y.; Ren, L.; Li, J. [R and D Center of Applied Superconductivity, Huazhong University of Science and Technology, Wuhan 430074 (China)

2010-11-01

Maglev rail is an important part of the magnetic levitation launch system. Reducing the manufacturing cost of magnetic levitation rail is the key problem for the development of magnetic levitation launch system. The Halbach permanent array has an advantage that the fundamental spatial field is cancelled on one side of the array while the field on the other side is enhanced. So this array used in the design of high temperature superconducting permanent maglev rail could improve the surface magnetic field and the levitation force. In order to make the best use of Nd-Fe-B (NdFeB) material and reduce the cost of maglev rail, the effect of the rail's structural parameters on levitation force and the utilization rate of NdFeB material are analyzed. The optimal ranges of these structural parameters are obtained. The mutual impact of these parameters is also discussed. The optimization method of these structure parameters is proposed at the end of this paper.

Control of rolling contact fatigue on premium rails in revenue service.

Science.gov (United States)

2014-11-01

Effective rail maintenance strategies are : essential for controlling rolling contact fatigue : (RCF) and reducing wear of rails under heavy : axle load (HAL) operations. In an effort to : optimize rail maintenance strategies in revenue : service, Tr...

NASTRAN buckling study of a linear induction motor reaction rail

Science.gov (United States)

Williams, J. G.

1973-01-01

NASTRAN was used to study problems associated with the installation of a linear induction motor reaction rail test track. Specific problems studied include determination of the critical axial compressive buckling stress and establishment of the lateral stiffness of the reaction rail under combined loads. NASTRAN results were compared with experimentally obtained values and satisfactory agreement was obtained. The reaction rail was found to buckle at an axial compressive stress of 11,400 pounds per square inch. The results of this investigation were used to select procedures for installation of the reaction rail.

Rail Base Corrosion and Cracking Prevention: Phase 2

Science.gov (United States)

2018-04-09

EWI was engaged by the Federal Railroad Administration to research rail treatments to prevent rail base corrosion in corrosive environments. A coating system was selected in Phase 1 and recommended for field trials. In Phase 2, four railroads sponsor...

Plans for crash-tested wood bridge railings for concrete decks

Science.gov (United States)

Michael A. Ritter; Ronald K. Faller; Barry T. Rosson; Paula D. Hilbrich Lee; Sheila Rimal. Duwadi

1998-01-01

As part of a continuing cooperative research between the Midwest Roadside Safety Facility (MwRSF); the USDA Forest Service, Forest Products Laboratory (FPL); and the Federal Highway Administration (FHWA), several crashworthy wood bridge railings and approach railing transitions have been adapted for use on concrete bridge decks. These railings meet testing and...

Linear and/or curvilinear rail mount system

Science.gov (United States)

Thomas, Jackie D. (Inventor); Harris, Lawanna L. (Inventor)

2012-01-01

One or more linear and/or curvilinear mounting rails are coupled to a structure. Each mounting rail defines a channel and at least one cartridge assembly is engaged in the channel. Each cartridge assembly includes a housing that slides within the channel. The housing defines a curvilinearly-shaped recess longitudinally aligned with the channel when the housing is in engagement therewith. The cartridge assembly also includes a cleat fitted in the recess for sliding engagement therealong. The cleat can be coupled to a fastener that passes through the mounting rail and the housing when the housing is so-engaged in the channel. The cleat is positioned in the recess by a position of the fastener.

Home school student visit and introduction to rail transportation and engineering.

Science.gov (United States)

2016-06-22

This project consisted of hosting local Champaign-Urbana, Illinois home school students for a visit to : the Rail Transportation and Engineering Center (RailTEC) at the University of Illinois at Urbana- : Champaign (UIUC). Beyond visiting RailTEC, st...

Rail Track Detection and Modelling in Mobile Laser Scanner Data

Directory of Open Access Journals (Sweden)

S. Oude Elberink

2013-10-01

Full Text Available We present a method for detecting and modelling rails in mobile laser scanner data. The detection is based on the properties of the rail tracks and contact wires such as relative height, linearity and relative position with respect to other objects. Points classified as rail track are used in a 3D modelling algorithm. The modelling is done by first fitting a parametric model of a rail piece to the points along each track, and estimating the position and orientation parameters of each piece model. For each position and orientation parameter a smooth low-order Fourier curve is interpolated. Using all interpolated parameters a mesh model of the rail is reconstructed. The method is explained using two areas from a dataset acquired by a LYNX mobile mapping system in a mountainous area. Residuals between railway laser points and 3D models are in the range of 2 cm. It is concluded that a curve fitting algorithm is essential to reliably and accurately model the rail tracks by using the knowledge that railways are following a continuous and smooth path.

Unistuste Rail Baltic - ilus ja kallis / Mikk Salu

Index Scriptorium Estoniae

Salu, Mikk, 1975-

2011-01-01

Rail Balticu puhul on tähtsaim küsimus, kas uut raudteeühendust on üldse vaja, mitte aga see, kas tee läheb läbi Tartu või Pärnu. Konsutatsioonifirma AECOM koostatud raportist Rail Balticu tasuvuse kohta

Rail freight transportation concerns of developing economies: A Namibian perspective

Directory of Open Access Journals (Sweden)

Fanny Saruchera

2017-05-01

Full Text Available Background: Although rail transport appears to be well established and outperforming other transport modes in Europe and beyond, in the majority of developing economies it was observed that firms and travellers were, on the contrary, shunning from the rail. Despite considerable infrastructural investments in the African rail systems, the sector has been deteriorating over the years. Objectives: This study identifies the freight rail transportation problems faced by African developing economies, focusing on Namibia, and examines the potential actions and factors for minimising such problems, drawing lessons from some of the developed world’s success stories. Method: The objectives of this study are achieved through a survey of Windhoek-based industrial and logistics firms operating in Namibia. Self-administered survey questionnaires were distributed through the aid of trained research assistants. Results: The study’s results show that some of the reasons of shunning rail transport are a matter of attitude, whereas some are related to operational challenges. The study confirms that the transport mode used and ownership of the freight transport services used can affect the degree of satisfaction for the transportation of goods in Namibia. Conclusion: Namibian industrial and logistics firms avoid using rail, owing to its low level of satisfaction obtained from its use. Besides engaging in Public Private Partnerships (PPPs in rail transport operations, the study contends that rail transport should receive attention similar to that given to other transport modes for African economies such as Namibia to overcome the costs associated with the increasing road congestion.

National Marine Fisheries Service Grain Size Data from the Baltimore Canyon Trough

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Grain size analyses produced by Robert Reid of the NOAA National Marine Fisheries Service for the NOAA/BLM Outer Continental Shelf Mid-Atlantic Project, Baltimore...

Bootstrap for rails

CERN Document Server

Rahman, Syed Fazle

2015-01-01

If you are a web developer who has a basic understanding of Ruby on Rails, this is the book for you. You should definitely have previous knowledge about HTML and how it works. However, CSS and JavaScript knowledge is optional for this book.

Numerical investigation on an array of Helmholtz resonators for the reduction of micro-pressure waves in modern and future high-speed rail tunnel systems

Science.gov (United States)

Tebbutt, J. A.; Vahdati, M.; Carolan, D.; Dear, J. P.

2017-07-01

Previous research has proposed that an array of Helmholtz resonators may be an effective method for suppressing the propagation of pressure and sound waves, generated by a high-speed train entering and moving in a tunnel. The array can be used to counteract environmental noise from tunnel portals and also the emergence of a shock wave in the tunnel. The implementation of an array of Helmholtz resonators in current and future high-speed train-tunnel systems is studied. Wave propagation in the tunnel is modelled using a quasi-one-dimensional formulation, accounting for non-linear effects, wall friction and the diffusivity of sound. A multi-objective genetic algorithm is then used to optimise the design of the array, subject to the geometric constraints of a demonstrative tunnel system and the incident wavefront in order to attenuate the propagation of pressure waves. It is shown that an array of Helmholtz resonators can be an effective countermeasure for various tunnel lengths. In addition, the array can be designed to function effectively over a wide operating envelope, ensuring it will still function effectively as train speeds increase into the future.

Groningen Seaports : An Examination of Public Rail Infrastructure

NARCIS (Netherlands)

Droogendijk, Gert

2010-01-01

This report examines the value of the public rail infrastructure of Groningen Seaports, the port authority of Delfzijl and Eemshaven. There is substantial strategic value of public rail infrastructure due to the public good character, the mission of Groningen Seaports, the image of full port

49 CFR 213.343 - Continuous welded rail (CWR).

Science.gov (United States)

2010-10-01

... ADMINISTRATION, DEPARTMENT OF TRANSPORTATION TRACK SAFETY STANDARDS Train Operations at Track Classes 6 and...) Designation of a desired rail installation temperature range for the geographic area in which the CWR is... installation temperature range when adjusting CWR. (b) Rail anchoring or fastening requirements that will...

77 FR 76169 - Quarterly Rail Cost Adjustment Factor

Science.gov (United States)

2012-12-26

....stb.dot.gov . Copies of the decision may be purchased by contacting the Office of Public Assistance...)] Quarterly Rail Cost Adjustment Factor AGENCY: Surface Transportation Board, DOT. ACTION: Approval of rail cost adjustment factor. SUMMARY: The Board has approved the AAR's proposed rebasing calculations and...

75 FR 53734 - Patriot Rail, LLC, Patriot Rail Holdings LLC, and Patriot Rail Corp.-Continuance in Control...

Science.gov (United States)

2010-09-01

... noncarrier limited liability company that owns not less than 51% of the equity interests in PRH. PRH owns 100% of the stock of Patriot. Patriot is a noncarrier holding company that owns 100% of the stock of six...). Patriot currently controls the following six Class III rail carriers: Tennessee Southern Railroad Company...

LOAD BEARING CAPACITY OF THE GLASS RAILING ELEMENT

Directory of Open Access Journals (Sweden)

Elizabeta Šamec

2016-02-01

Full Text Available In this paper some basic physical and mechanical properties of glass as structural material are presented. This research is about specifically manufactured glass railing element that will be a part of a pedestrian bridge construction in Zagreb, Croatia. Load bearing capacity test of the glass railing element is conducted within the Faculty of Civil Engineering in Zagreb and obtained experimental results are discussed and compared to the ones provided by the numerical model. Taking into account the behaviour of laminated glass and results of experimental and numerical testing, glass railing element can be regarded as safe.

World Geography. The Port of Baltimore Workplace Skills Development Project.

Science.gov (United States)

Walker, Sam

This set of learning modules was developed during a project to deliver workplace literacy instruction to individuals employed in the more than 50 businesses related to the activities of the Port of Baltimore. It is intended to accomplish the following objectives: familiarize students with basic concepts of geography; give students knowledge of…

Tartu ihkab Rail Baltica kiirraudteed endale / Madis Aesma

Index Scriptorium Estoniae

Aesma, Madis

2005-01-01

2005. aasta sügisel alustatakse uuringuid, et välja selgitada, millisest Eesti linnast - Tartust, Pärnust või Viljandist - peaks tulevikus läbi minema kiirraudtee Rail Baltica, mis viib kuue tunniga Tallinnast Varssavisse. Kaart: Kiirraudtee Rail Baltica kolm võimalikku suunda. Kommenteerib Andrus Ansip

Review on Selection and Suitability of Rail Transit Station Design Pertaining to Public Safety

Science.gov (United States)

Akabal, Farah Mohd; Masirin, Mohd Idrus Haji Mohd; Abidin Akasah, Zainal; Rohani, Munzilah Md

2017-08-01

Railway has emerged as a fast, convenient, safe, clean, and low-cost alternative to air and road transportation. Many countries have invested in rail transportation. In America, Europe and Asia, large investments are planned for rail transportation. This is because congestion problems can be reduced with the introduction of rail transportation. Rail transportation involves several components which are important to ensure the smooth and safe delivery of services such as locomotives, rail stations and railway tracks. Rail transit stations are places where trains stop to pick-up and drop-off passengers. Stations are vital for many to enable them to engage in work and social commitments. This paper focuses only on the rail transit station as it is one of the important components in rail transportation. It is also considered as a key public meeting place and space for interactions in a community. The role of rail transit station and the requirements of a good rail transit station are also described in this paper. Steps in selecting the location of rail transit station include the function and facilities in rail transit station are discussed with reference to best practices and handbooks. Selection of the appropriate rail transit station locations may help users indirectly. In addition, this paper will also elucidate on the design considerations for an efficient and effective rail transit station. Design selections for the rail transit station must be balanced between aesthetic value and functional efficiency. The right design selection may help conserve energy, assure and facilitate consumers even thought a rail transit station plays a smaller role in attracting consumers compared to a shopping complex or a residential building. This will contribute towards better and greener building for a green transportation facility. Thus, with this paper it is expected to assist the relevant authority to identify important elements in the selection and determination of suitable

Mechatronic modeling of real-time wheel-rail contact

CERN Document Server

Bosso, Nicola; Gugliotta, Antonio; Somà, Aurelio

2013-01-01

Real-time simulations of the behaviour of a rail vehicle require realistic solutions of the wheel-rail contact problem which can work in a real-time mode. Examples of such solutions for the online mode have been well known and are implemented within standard and commercial tools for the simulation codes for rail vehicle dynamics. This book is the result of the research activities carried out by the Railway Technology Lab of the Department of Mechanical and Aerospace Engineering at Politecnico di Torino. This book presents work on the project for the development of a real-time wheel-rail contact model and provides the simulation results obtained with dSpace real-time hardware. Besides this, the implementation of the contact model for the development of a real-time model for the complex mechatronic system of a scaled test rig is presented in this book and may be useful for the further validation of the real-time contact model with experiments on a full scale test rig.

Top-of-Rail lubricant

Energy Technology Data Exchange (ETDEWEB)

Alzoubi, M. F.; Fenske, G. R.; Erck, R. A.; Boparai, A. S.

2000-07-14

Analysis of the volatile and semivolatile fractions collected after use of the TOR lubricant indicated that other than contaminants in the collection laboratory, no compounds on the EPA's Target Compound Lists (Tables 2 and 5) were detected in these fractions. The data of these qualitative analyses, given in the various tables in the text, indicate only the relative amounts of the tentatively identified compounds. The authors recommend that quantitative analysis be performed on the volatile and semivolatile fractions to allow confirmation of the tentatively identified compounds and to obtain absolute amounts of the detected compounds. Additionally, the semivolatile fraction should be analyzed by liquid chromatography/mass spectrometry to identify compounds that are not chromatographable under the temperature program used for determination of semivolatile compounds. Introducing the top-of-rail (TOR) lubricant into the wheel/rail interface results in a reduction of almost 60% of lateral friction force over the forces encountered under dry conditions. This reveals good potential for energy savings, as well as wear reduction, for railroad companies. In TOR lubrication, an increase in the angle of attack and axle load results in increased lateral friction and rate of lubricant consumption. The most efficient TOR lubricant quantity to be used in the wheel/rail interface must be calculated precisely according to the number of cars, axle loads, train speed, and angle of attack.

LeRC rail accelerators: test designs and diagnostic techniques

International Nuclear Information System (INIS)

Zana, L.M.; Kerslake, W.R.; Sturman, J.C.; Wang, S.Y.; Terdan, F.F.

1984-01-01

The feasibility of using rail accelerators for various in-space and to-space propulsion applications was investigated. A 1 meter, 24 sq mm bore accelerator was designed with the goal of demonstrating projectile velocities of 15 km/sec using a peak current of 200 kA. A second rail accelerator, 1 meter long with a 156.25 sq mm bore, was designed with clear polycarbonate sidewalls to permit visual observation of the plasma arc. A study of available diagnostic techniques and their application to the rail accelerator is presented. Specific topics of discussion include the use of interferometry and spectroscopy to examine the plasma armature as well as the use of optical sensors to measure rail displacement during acceleration. Standard diagnostics such as current and voltage measurements are also discussed. 15 references

On the Feasibility of High Speed Railway mmWave Channels in Tunnel Scenario

Directory of Open Access Journals (Sweden)

Guangkai Li

2017-01-01

Full Text Available Rail traffic is widely acknowledged as an efficient and green transportation pattern and its evolution attracts a lot of attention. However, the key point of the evolution is how to develop the railway services from traditional handling of the critical signaling applications only to high data rate applications, such as real-time videos for surveillance and entertainments. The promising method is trying to use millimeter wave which includes dozens of GHz bandwidths to bridge the high rate demand and frequency shortage. In this paper, the channel characteristics in an arched railway tunnel are investigated owing to their significance of designing reliable communication systems. Meantime, as millimeter wave suffers from higher propagation loss, directional antenna is widely accepted for designing the communication system. The specific changes that directional antenna brings to the radio channel are studied and compared to the performances of omnidirectional antenna. Note that the study is based on enhanced wide-band ray tracing tool where the electromagnetic and scattering parameters of the main materials of the tunnel are measured and fitted with predicting models.

36 CFR 1192.175 - High-speed rail cars, monorails and systems.

Science.gov (United States)

2010-07-01

..., monorails and systems. 1192.175 Section 1192.175 Parks, Forests, and Public Property ARCHITECTURAL AND... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.175 High-speed rail cars, monorails and systems. (a... steel-wheel-on-steel-rail technology, and monorail systems operating primarily on dedicated rail (i.e...

Material Evaluation of an Elastomer, Epoxy and Lightweight Concrete Rail Attachment System for Direct Fixation Light Rail Applications

Science.gov (United States)

Swarner, Benjamin R.

Sound Transit plans to extend its current light rail system, which runs along the I-5 corridor in Seattle, Washington, across the I-90 Homer Hadley floating bridge as part of a project to connect the major city centers in the region. But, no light rail has ever crossed a floating bridge due to several unique engineering challenges. One of these challenges is attaching the rails to the existing bridge deck without drilling into the bridge pontoons. This research program was developed to test and analyze a direct fixation method that uses lightweight concrete plinths and an elastomer-epoxy system to attach the rails to the bridge deck. The elastomer used was a two-part, pourable elastomer with cork particles intermixed to alter the mechanical properties of the material. A lightweight concrete mixture was analyzed for use in the plinths, and system tests investigated the system response under tensile, compressive and shear loading. The shear response of the system was examined further under varying loading conditions including different surface preparations, elastomer thicknesses, strain-rates and after freeze-thaw conditioning. Experimental data was examined for trends based on these parameters to best characterize the system, and the elastomer was evaluated in the context of modern elastomer research.

Evaluating autonomous acoustic surveying techniques for rails in tidal marshes

Science.gov (United States)

Stiffler, Lydia L.; Anderson, James T.; Katzner, Todd

2018-01-01

There is a growing interest toward the use of autonomous recording units (ARUs) for acoustic surveying of secretive marsh bird populations. However, there is little information on how ARUs compare to human surveyors or how best to use ARU data that can be collected continuously throughout the day. We used ARUs to conduct 2 acoustic surveys for king (Rallus elegans) and clapper rails (R. crepitans) within a tidal marsh complex along the Pamunkey River, Virginia, USA, during May–July 2015. To determine the effectiveness of an ARU in replacing human personnel, we compared results of callback point‐count surveys with concurrent acoustic recordings and calculated estimates of detection probability for both rail species combined. The success of ARUs at detecting rails that human observers recorded decreased with distance (P ≤ 0.001), such that at of human‐recorded rails also were detected by the ARU, but at >75 m, only 34.0% of human‐detected rails were detected by the ARU. To determine a subsampling scheme for continuous ARU data that allows for effective surveying of presence and call rates of rails, we used ARUs to conduct 15 continuous 48‐hr passive surveys, generating 720 hr of recordings. We established 5 subsampling periods of 5, 10, 15, 30, and 45 min to evaluate ARU‐based presence and vocalization detections of rails compared with each of the full 60‐min sampling of ARU‐based detection of rails. All subsampling periods resulted in different (P ≤ 0.001) detection rates and unstandardized vocalization rates compared with the hourly sampling period. However, standardized vocalization counts from the 30‐min subsampling period were not different from vocalization counts of the full hourly sampling period. When surveying rail species in estuarine environments, species‐, habitat‐, and ARU‐specific limitations to ARU sampling should be considered when making inferences about abundances and distributions from ARU data. 

77 FR 65937 - Pioneer Railcorp-Continuation in Control Exemption-Rail Switching Services, Inc.

Science.gov (United States)

2012-10-31

... control of Rail Switching Services, Inc. (RSS), upon RSS's becoming a Class III rail carrier. \\1\\ Pioneer states that it owns 100% of the common stock of its 17 Class III rail carrier subsidiaries: West Michigan...--Continuation in Control Exemption--Rail Switching Services, Inc. Pioneer Railcorp (Pioneer) and its...

Common rail technology for future low emission diesel vehicles; Common Rail Technologie fuer zukuenftige Diesel Fahrzeuge mit niedrigen Emissionswerten

Energy Technology Data Exchange (ETDEWEB)

Schoeppe, D.; Bercher, P.; Guerrassi, N.; Spadafora, P.

2004-07-01

The diesel fuel injection equipment will remain a key element for diesel engine technology evolution. Achieving emission targets at competitive prices has been and will continue to be a major technical challenge to the engine manufacturer. Delphi is continuously developing its common rail system and its components to fulfill future stricter emission legislation while simultaneously improving performance on noise, fuel consumption and power output. This paper will describe the latest developments that delphi introduced into the market in their common rail system to comply with future legislative emission targets. Further, a novel common rail injector will be presented, that uses a revolutionary, direct acting operating principle, where the nozzle is directly operated by a piezo actuator, without the use of a servo-hydraulic flow circuit. The superior performance of this injector concept will be shown, especially in minimum quantity capability as well as multiple injection performance. The direct acting operating principle allows rapid opening and closing of the injector, without compromising pilot quantity capability. The emission benefit obtained by such opening and closing behavior will be shown. Finally, based on the findings discussed, the paper will conclude on key features of future common rail systems. (orig.)

Hybrid rail gun electromagnetic accelerators

International Nuclear Information System (INIS)

Chen, K.W.; Hachen, H.; Lee, A.; Legh, G.; Lin, T.; Mattay, S.; Wipf, S.

1983-01-01

Theoretical and experimental investigations on hybrid rail accelerators are presented. It is shown that the side surface areas and in some cases sabots of the projectile can be used to provide substantial amount of additional thrust. Moreover, it is shown that in most cases examined, external magnetic fields can be conveniently incorporated in the accelerator designs to supplement the rail-induced fields. Total thrusts in excess of 10 MN for kilogram-sized projectiles can in principle be established with driving currents of the order of 1 MA. No obvious stress limitations are foreseen. The percentages of thrust from external magnetic fields are sufficiently high that the use of which should be encouraged. The increased flexibility in the projectile shapes available permits the use of the proposed hybrid electromagnetic launcher technology in a variety of new areas, such as thrust boosts in conventional chemical rockets and other similar applications. Furthermore, the additional thrust obtained from the use of side surface areas greatly increases the maximum permissable thrust otherwise limited by material strength considerations. Thrust analyses for projectiles in several hybrid rail accelerator designs are discussed. Some laboratory experimental observations are presented

MASH Test 3-11 on the T131RC Bridge Rail

Science.gov (United States)

2012-10-01

Texas Department of Transportation (TxDOT) currently uses the TxDOT Type T101RC Bridge Rail, : a steel post and beam bridge rail anchored to the top of concrete curbs. The T101RC Bridge Rail is : 27 inches in height and can be anchored to the top of ...

Wavenumber-domain separation of rail contribution to pass-by noise

Science.gov (United States)

Zea, Elias; Manzari, Luca; Squicciarini, Giacomo; Feng, Leping; Thompson, David; Arteaga, Ines Lopez

2017-11-01

In order to counteract the problem of railway noise and its environmental impact, passing trains in Europe must be tested in accordance to a noise legislation that demands the quantification of the noise generated by the vehicle alone. However, for frequencies between about 500 Hz and 1600 Hz, it has been found that a significant part of the measured noise is generated by the rail, which behaves like a distributed source and radiates plane waves as a result of the contact with the train's wheels. Thus the need arises for separating the rail contribution to the pass-by noise in that particular frequency range. To this end, the present paper introduces a wavenumber-domain filtering technique, referred to as wave signature extraction, which requires a line microphone array parallel to the rail, and two accelerometers on the rail in the vertical and lateral direction. The novel contributions of this research are: (i) the introduction and application of wavenumber (or plane-wave) filters to pass-by data measured with a microphone array located in the near-field of the rail, and (ii) the design of such filters without prior information of the structural properties of the rail. The latter is achieved by recording the array pressure, as well as the rail vibrations with the accelerometers, before and after the train pass-by. The performance of the proposed method is investigated with a set of pass-by measurements performed in Germany. The results seem to be promising when compared to reference data from TWINS, and the largest discrepancies occur above 1600 Hz and are attributed to plane waves radiated by the rail that so far have not been accounted for in the design of the filters.

Evaluating autonomous acoustic surveying techniques for rails in tidal marshes

Science.gov (United States)

Stiffler, Lydia L.; Anderson, James T.; Katzner, Todd

2018-01-01

There is a growing interest toward the use of autonomous recording units (ARUs) for acoustic surveying of secretive marsh bird populations. However, there is little information on how ARUs compare to human surveyors or how best to use ARU data that can be collected continuously throughout the day. We used ARUs to conduct 2 acoustic surveys for king (Rallus elegans) and clapper rails (R. crepitans) within a tidal marsh complex along the Pamunkey River, Virginia, USA, during May–July 2015. To determine the effectiveness of an ARU in replacing human personnel, we compared results of callback point‐count surveys with concurrent acoustic recordings and calculated estimates of detection probability for both rail species combined. The success of ARUs at detecting rails that human observers recorded decreased with distance (P ≤ 0.001), such that at 75 m, only 34.0% of human‐detected rails were detected by the ARU. To determine a subsampling scheme for continuous ARU data that allows for effective surveying of presence and call rates of rails, we used ARUs to conduct 15 continuous 48‐hr passive surveys, generating 720 hr of recordings. We established 5 subsampling periods of 5, 10, 15, 30, and 45 min to evaluate ARU‐based presence and vocalization detections of rails compared with each of the full 60‐min sampling of ARU‐based detection of rails. All subsampling periods resulted in different (P ≤ 0.001) detection rates and unstandardized vocalization rates compared with the hourly sampling period. However, standardized vocalization counts from the 30‐min subsampling period were not different from vocalization counts of the full hourly sampling period. When surveying rail species in estuarine environments, species‐, habitat‐, and ARU‐specific limitations to ARU sampling should be considered when making inferences about abundances and distributions from ARU data. 

California statewide model for high-speed rail

OpenAIRE

Outwater, Maren; Tierney, Kevin; Bradley, Mark; Sall, Elizabeth; Kuppam, Arun; Modugala, Vamsee

2010-01-01

The California High Speed Rail Authority (CHSRA) and the Metropolitan Transportation Commission (MTC) have developed a new statewide model to support evaluation of high-speed rail alternatives in the State of California. This statewide model will also support future planning activities of the California Department of Transportation (Caltrans). The approach to this statewide model explicitly recognizes the unique characteristics of intraregional travel demand and interregional travel demand. A...

Policy issues of transporting spent nuclear fuel by rail

International Nuclear Information System (INIS)

Spraggins, H.B.

1994-01-01

The topic of this paper is safe and economical transportation of spent nuclear fuel by rail. The cost of safe movement given the liability consequences in the event of a rail accident involving such material is the core issue. Underlying this issue is the ability to access the risk probability of such an accident. The paper delineates how the rail industry and certain governmental agencies perceive and assess such important operational, safety, and economic issues. It also covers benefits and drawbacks of dedicated and regular train movement of such materials

RAIL TRAFFIC VOLUME ESTIMATION BASED ON WORLD DEVELOPMENT INDICATORS

Directory of Open Access Journals (Sweden)

Luka Lazarević

2015-08-01

Full Text Available European transport policy, defined in the White Paper, supports shift from road to rail and waterborne transport. The hypothesis of the paper is that changes in the economic environment influence rail traffic volume. Therefore, a model for prediction of rail traffic volume applied in different economic contexts could be a valuable tool for the transport planners. The model was built using common Machine Learning techniques that learn from the past experience. In the model preparation, world development indicators defined by the World Bank were used as input parameters.

Advancing high-speed rail policy in the United States.

Science.gov (United States)

2012-06-01

This report builds on a review of international experience with high-speed rail projects to develop recommendations for a High-speed rail policy framework for the United States. The international review looked at the experience of Korea, Taiwan, Chin...

Perspectives on Obesity and Its Treatment: Health Care Providers and the General Public in Rural West Virginia and Urban Baltimore

Science.gov (United States)

Menez, Steven; Cheskin, Lawrence; Geller, Gail

2013-01-01

Objective: To determine and compare the perspectives of the general public and health care providers (HCPs) on obesity and its treatment in rural West Virginia (WV) and Baltimore, MD. Method: Surveys were completed in both locations by the general public (WV: "n" = 200; Baltimore: "n" = 171) and HCPs (WV: "n" = 25;…

Rail assembly for use in a radioactive environment

International Nuclear Information System (INIS)

Watts, R.E.

1989-01-01

An improved rail assembly and method of construction thereof is disclosed herein that is particularly adapted for use with a crane trolley in a hot cell environment which is exposed to airborne and liquidborne radioactive contaminants. The rail assembly is generally comprised of a support wall having an elongated, rail-housing recess having a floor, side wall and ceiling. The floor of the recess is defined at least in party by the load-bearing surface of a rail, and is substantially flat, level and crevice-free to facilitate the drainage of liquids out of the recess. The ceiling of the recess overhangs and thereby captures trolley wheels within the recess to prevent them from becoming dislodged from the recess during a seismic disturbance. Finally, the interior of the recess includes a power track having a slot for receiving a sliding electrical connector from the crane trolley. The power track is mounted in an upper corner of the recess with its connector-receiving groove oriented downwardly to facilitate the drainage of liquidborne contaminants and to discourage the collection of airborne contaminants within the track

Noise and Vibration Mitigation for Rail Transportation Systems : Proceedings of the 10th International Workshop on RailwayNoise

CERN Document Server

Gautier, Pierre-Etienne; Hanson, Carl; Hemsworth, Brian; Nelson, James; Schulte-Werning, Burkhard; Thompson, David; Vos, Paul

2012-01-01

This volume contains the contributions to the 10th International Workshop on Railway Noise, held October 18–22, 2010, in Nagahama, Japan, organized by the Railway Technical Research Institute (RTRI), Japan. With 11 sessions and 3 poster sessions, the workshop featured presentations by international leaders in the field of railway noise and vibration. All subjects relating to 1. prospects, legal regulation, and perception; 2. wheel and rail noise; 3. structure-borne noise and squeal noise; 4. ground-borne vibration; 5. aerodynamic noise and micro-pressure waves from tunnel portals; 6. interior noise and sound barriers; and 7. prediction, measurements, and monitoring are addressed here. This book is a useful “state-of-the-art” reference for scientists and engineers involved in solving environmental problems of railways.

Launch of Village Blue Web Application Shares Water Monitoring Data with Baltimore Community

Science.gov (United States)

EPA and the U.S. Geological Survey (USGS) have launched their mobile-friendly web application for Village Blue, a project that provides real-time water quality monitoring data to the Baltimore, Maryland community.

To the question of modeling of wheels and rails wear processes

Directory of Open Access Journals (Sweden)

S.V. Myamlin

2013-06-01

Full Text Available Purpose. There is a need of wear process modeling in the wheel-rail system. This is related to the fact that the wear processes in this system are absolutely different in the initial and final stages. The profile change of rail and, especially, of the wheels caused by the wear significantly affects the rolling stock dynamics, traffic safety and the resource of the wheels and rails. Wear modeling and the traffic safety evaluation requires the accounting of the low frequency component forces (including the modeling of transitional areas affecting the wheel on the side of the rail and carriage in motion of rolling stock, so the statistical analysis is not possible. Methodology. The method of mathematical modeling of the wheel set and the rail interaction was used during the research conducting. Findings. As a result of the modeling of the wheel set motion on the rail track, the mathematic model with 19 freedom degrees was obtained. This model takes into account the axle torque and studies wheels constructions as the components of the mechanical systems, consisting of a hub and tire. Originality. The mathematic model allows evaluating the wear degree of the wheels and rails when using on the rolling stock not only all-metal wheel sets, but also compound ones with the use of spring wheels and independent rotation of semi-axes with the wheels. Practical value. The development of the improved mathematical model of freight car wheel set motion with differential rotation of the wheels and compound axles allows studying the wear processes of wheels and rails.

Tunneling technologies for the collider ring tunnels

International Nuclear Information System (INIS)

Frobenius, P.

1989-01-01

The Texas site chosen for the Superconducting Super Collider has been studied, and it has been determined that proven, conventional technology and accepted engineering practice are suitable for constructing the collider tunnels. The Texas National Research Laboratory Commission report recommended that two types of tunneling machines be used for construction of the tunnels: a conventional hard rock tunnel boring machine (TBM) for the Austin chalk and a double shielded, rotary TBM for the Taylor marl. Since the tunneling machines usually set the pace for the project, efficient planning, operation, and coordination of the tunneling system components will be critical to the schedule and cost of the project. During design, tunneling rate prediction should be refined by focusing on the development of an effective tunneling system and evaluating its capacity to meet or exceed the required schedules. 8 refs., 13 figs

77 FR 65446 - Turtle Creek Industrial Railroad, Inc.-Acquisition and Operation Exemption-Consolidated Rail...

Science.gov (United States)

2012-10-26

... common carrier providing interstate rail service, primarily for Dura-Bond, without first obtaining... Industrial Railroad, Inc.--Acquisition and Operation Exemption--Consolidated Rail Corporation Turtle Creek... Consolidated Rail Corporation (Conrail) and to operate approximately 9.8 miles of rail line between milepost 0...

75 FR 51160 - Swanson Rail Transfer, L.P.-Lease and Operation Exemption-BDB Company

Science.gov (United States)

2010-08-18

... truck-rail transfer facility on the property and provide associated rail common carrier services. \\1... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35399] Swanson Rail Transfer, L.P.--Lease and Operation Exemption--BDB Company Swanson Rail Transfer, L.P. (SRT), a noncarrier...

The wheel-rail contact friction influence on high speed vehicle model stability

Directory of Open Access Journals (Sweden)

Mirosław DUSZA

2015-09-01

Full Text Available Right estimating of the coefficient of friction between the wheel and rail is essential in modelling rail vehicle dynamics. Constant value of coefficient of friction is the typical assumption in theoretical studies. But it is obvious that in real circumstances a few factors may have significant influence on the rails surface condition and this way on the coefficient of friction value. For example the weather condition, the railway location etc. Influence of the coefficient of friction changes on high speed rail vehicle model dynamics is presented in this paper. Four axle rail vehicle model were built. The FASTSIM code is employed for calculation of the tangential contact forces between wheel and rail. One coefficient of friction value is adopted in the particular simulation process. To check the vehicle model properties under the influence of wheel-rail coefficient of friction changes, twenty four series of simulations were performed. For three curved tracks of radii R = 3000m, 6000m and  (straight track, the coefficient of friction was changed from 0.1 to 0.8. The results are presented in form of bifurcation diagrams.

Large scale implementation of guided wave based broken rail monitoring

Science.gov (United States)

Burger, Francois A.; Loveday, Philip W.; Long, Craig S.

2015-03-01

A guided wave ultrasound system has been developed over the past 17 years to detect breaks in continuously welded rail track. Installation of the version 4 system on an 840 km long heavy duty freight line was conducted between January 2013 and June 2014. The system operates in pitch - catch mode with alternate transmit and receive transducers spaced approximately 1km apart. If the acoustic signal is not received at the receive station an alarm is triggered to indicate a break in the rail between the transmit station and the receive station. The system is permanently installed, powered by solar panels and issues broken rail alarms using the GSM network where available, and digital radio technology in other areas. A total of 931 stations were installed and the entire length of rail is interrogated every fifteen minutes. The system operates reliably although some problems involving unreliable GSM communication and theft of solar panels have been experienced. In the first two months of operation four broken rails were detected and train operation was halted temporarily for repairs.

A Historical Evaluation of the U12t Tunnel, Nevada Test Site, Nye County, Nevada, Volume 6 of 6

Energy Technology Data Exchange (ETDEWEB)

Harold Drollinger; Robert C. Jones; and Thomas F. Bullard; Desert Research Institute, Laurence J. Ashbaugh, Southern Nevada Courier Service and Wayne R. Griffin, Stoller-Navarro Joint Venture

2009-02-01

This report presents a historical evaluation of the U12t Tunnel on the Nevada Test Site in southern Nevada. The work was conducted by the Desert Research Institute at the request of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office and the U.S. Department of Defense, Defense Threat Reduction Agency (DTRA). The U12t Tunnel is one of a series of tunnels used for underground nuclear weapons effects tests on the east side of Rainier and Aqueduct Mesas. Six nuclear weapons effects tests, Mint Leaf, Diamond Sculls, Husky Pup, Midas Myth/Milagro, Mighty Oak, and Mission Ghost, and one high explosive test, SPLAT, were conducted within the U12t Tunnel from 1970 to 1987. All six of the nuclear weapons effects tests and the high explosive test were sponsored by DTRA. Two conventional weapons experiments, Dipole Knight and Divine Eagle, were conducted in the tunnel portal area in 1997 and 1998. These experiments were sponsored by the Defense Special Weapons Agency. The U12t Tunnel complex is composed of the Portal and Mesa Areas and includes an underground tunnel with a main access drift and nine primary drifts, a substantial tailings pile fronting the tunnel portal, a series of discharge ponds downslope of the tailings pile, and two instrumentation trailer parks and 16 drill holes on top of Aqueduct Mesa. A total of 89 cultural features were recorded: 54 at the portal and 35 on the mesa. In the Portal Area, cultural features are mostly concrete pads and building foundations; other features include the portal, rail lines, the camel back, ventilation and cooling system components, communication equipment, and electrical equipment. On the mesa are drill holes, a few concrete pads, a loading ramp, and electrical equipment.

A Historical Evaluation of the U12t Tunnel, Nevada Test Site, Nye County, Nevada, Volume 1 of 6

Energy Technology Data Exchange (ETDEWEB)

Drollinger, Harold [Desert Research Institute (DRI), Nevada System of Higher Education, Reno,NV (United States); Jones, Robert C. [Desert Research Institute (DRI), Nevada System of Higher Education, Reno,NV (United States); Bullard, Thomas F. [Desert Research Institute (DRI), Nevada System of Higher Education, Reno,NV (United States); Ashbaugh, Laurence J. [Southern Nevada Courier Service, NV (United States); Griffin, Wayne R. [Stoller-Navarro Joint Venture, Las Vegas, NV (United States)

2009-02-01

This report presents a historical evaluation of the U12t Tunnel on the Nevada Test Site in southern Nevada. The work was conducted by the Desert Research Institute at the request of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office and the U.S. Department of Defense, Defense Threat Reduction Agency (DTRA). The U12t Tunnel is one of a series of tunnels used for underground nuclear weapons effects tests on the east side of Rainier and Aqueduct Mesas. Six nuclear weapons effects tests, Mint Leaf, Diamond Sculls, Husky Pup, Midas Myth/Milagro, Mighty Oak, and Mission Ghost, and one high explosive test, SPLAT, were conducted within the U12t Tunnel from 1970 to 1987. All six of the nuclear weapons effects tests and the high explosive test were sponsored by DTRA. Two conventional weapons experiments, Dipole Knight and Divine Eagle, were conducted in the tunnel portal area in 1997 and 1998. These experiments were sponsored by the Defense Special Weapons Agency. The U12t Tunnel complex is composed of the Portal and Mesa Areas and includes an underground tunnel with a main access drift and nine primary drifts, a substantial tailings pile fronting the tunnel portal, a series of discharge ponds downslope of the tailings pile, and two instrumentation trailer parks and 16 drill holes on top of Aqueduct Mesa. A total of 89 cultural features were recorded: 54 at the portal and 35 on the mesa. In the Portal Area, cultural features are mostly concrete pads and building foundations; other features include the portal, rail lines, the camel back, ventilation and cooling system components, communication equipment, and electrical equipment. On the mesa are drill holes, a few concrete pads, a loading ramp, and electrical equipment.

An investigation on the desired properties of friction modifiers for slippery rails

NARCIS (Netherlands)

Li, Z.; Arias Cuevas, O.

2009-01-01

The adhesion level between wheel and rail has been since the beginning of railway a crucial parameter in the design and operation of rail vehicles. In the last decades, many railway organizations have suffered from low adhesion problems as consequence of the increased exploitation of the rail

Atlanta Rail Yard Study: Evaluation of local-scale air pollution ...

Science.gov (United States)

Intermodal rail yards are important nodes in the freight transportation network, where freight is organized and moved from one mode of transport to another, critical equipment is serviced, and freight is routed to its next destination. Rail yard environments are also areas with multiple sources of air pollutant emissions (e.g., heavy-duty vehicles, locomotives, cranes), which may affect local air quality in residential areas nearby. In order to understand emissions and related air quality impacts, two field studies took place over the time span of 2010-2012 to measure air pollution trends in close proximity to the Inman and Tilford rail yard complex in Atlanta, GA. One field study involved long-term stationary monitoring of black carbon, fine particles, and carbon dioxide at two stations nearby the rail yard. In addition, a second field study performed intensive mobile air monitoring for a one month period in the summer of 2012 at a roadway network surrounding the rail yard complex and measured a comprehensive array of pollutants. Real-time mobile particulate measurements included particle counts, extinction coefficient, black carbon via light-absorption and particle incandescence, and particle composition derived by aerosol mass spectrometry. Gas-phase measurements included oxides of nitrogen, sulfur dioxide, carbon dioxide, and air toxics (e.g., benzene). Both sets of measurements determined detectable local influence from rail yard-related emissions.

A 72-dB-SNDR rail-to-rail successive approximation ADC using mismatch calibration techniques

International Nuclear Information System (INIS)

Liu Yan; Hua Siliang; Wang Donghui; Hou Chaohuan

2012-01-01

When the voltage of an analog input signal is equal to the supply voltage, it is difficult for a conventional successive approximation ADC to correctly convert the analog signal into digital signal. This paper introduces an improved successive approximation ADC, which can convert the rail-to-rail input range and reduce sampling time through a track-and-hold circuit. Comparator offset cancellation and capacitor self-calibration techniques are used in this ADC. Measurement results show that the peak SNDR of this ADC reaches 72 dB and the signal effective bandwidth is up to 1.25 MHz. It consumes 1 mW in the test, and the figure of merit is 123 fJ/conversion-step. (semiconductor integrated circuits)

Integrative approaches to investigating human-natural systems: the Baltimore ecosystem study

Science.gov (United States)

Mary L. Cadenasso; Steward T.A. Pickett; Morgan J. Grove; Morgan J. Grove

2006-01-01

This paper presents an overview of the research approaches used to study metropolitan Baltimore (Maryland, USA) as an ecological system. The urban ecosystem is a complex of biophysical, social, and built components, and is studied by an interdisciplinary teamof biological, social, and physical scientists, and urban designers. Ecology ?of? themetropolis is addressed...

Development and application of resilient wheels in urban rail transit vehicle

Directory of Open Access Journals (Sweden)

Juan WEN

Full Text Available Urban rail transit vehicles have been more and more attractive to people as a kind of fast, comfortable, energy-saving, environmental protection and safe transportation. But because of the vehicle noise and vibration, urban rail vehicles also face severe challenges. The research of resilient wheels has been continuously developed and improved. Based on the review of development background and structure sorts of resilient wheels, the advantages of resilient wheels are described, and the research status of noise and vibration reducing, infinite element strength analysis, vehicle dynamic analysis and the wheel-rail wear of resilient wheels are discussed. Taking the low-floor LRVs (light rail vehicles in domestic and overseas as example, the development and application of the resilient wheels in city rail transit is described, and the application prospects of the resilient wheels in LRVs in domestic and the future research direction of elastic wheel are discussed.

Semi-supervised rail defect detection from imbalanced image data

NARCIS (Netherlands)

Hajizadeh, S.; Nunez Vicencio, Alfredo; Tax, D.M.J.; Acarman, Tankut

2016-01-01

Rail defect detection by video cameras has recently gained much attention in both
academia and industry. Rail image data has two properties. It is highly imbalanced towards the non-defective class and it has a large number of unlabeled data samples available for semisupervised learning

Procedure and applications of combined wheel/rail roughness measurement

NARCIS (Netherlands)

Dittrich, M.G.

2009-01-01

Wheel-rail roughness is known to be the main excitation source of railway rolling noise. Besides the already standardised method for direct roughness measurement, it is also possible to measure combined wheel-rail roughness from vertical railhead vibration during a train pass-by. This is a different

Train Dwell Time Models for Rail Passenger Service

Directory of Open Access Journals (Sweden)

San Hor Peay

2016-01-01

Full Text Available In recent years, more studies had been conducted about train dwell time as it is a key parameter of rail system performance and reliability. This paper draws an overview of train dwell time models for rail passenger service from various continents, namely Asia, North America, Europe and Australia. The factors affecting train dwell time are identified and analysed across some rail network operators. The dwell time models developed by various researches are also discussed and reviewed. Finally, the contributions from the outcomes of these models are briefly addressed. In conclusion, this paper suggests that there is a need to further study the factors with strong influence upon dwell time to improve the quality of the train services.

Market size and vertical structure in the rail way industry

OpenAIRE

Matsushima, Noriaki; Mizutani, Fumitoshi

2011-01-01

We provide a theoretical framework to discuss the relation between market size and vertical structure in the railway industry. The framework is based on a simple downstream monopoly model with two input suppliers, labor forces and the rail infrastructure firm. The operation of the downstream firm (i.e., the train operating firm) generates costs on the rail infrastructure firm. We show that the downstream firm with a larger market size is more likely to integrate with the rail infrastructure f...

High pressure common rail injection system modeling and control.

Science.gov (United States)

Wang, H P; Zheng, D; Tian, Y

2016-07-01

In this paper modeling and common-rail pressure control of high pressure common rail injection system (HPCRIS) is presented. The proposed mathematical model of high pressure common rail injection system which contains three sub-systems: high pressure pump sub-model, common rail sub-model and injector sub-model is a relative complicated nonlinear system. The mathematical model is validated by the software Matlab and a virtual detailed simulation environment. For the considered HPCRIS, an effective model free controller which is called Extended State Observer - based intelligent Proportional Integral (ESO-based iPI) controller is designed. And this proposed method is composed mainly of the referred ESO observer, and a time delay estimation based iPI controller. Finally, to demonstrate the performances of the proposed controller, the proposed ESO-based iPI controller is compared with a conventional PID controller and ADRC. Copyright © 2016 ISA. Published by Elsevier Ltd. All rights reserved.

Phase I development of an aesthetic, precast concrete bridge rail.

Science.gov (United States)

2012-02-01

Precast concrete bridge rail systems offer several advantages over traditional cast-in-place rail designs, including reduced construction : time and costs, installation in a wide range of environmental conditions, easier maintenance and repair, impro...

Allocation of petroleum feedstock: Baltimore Gas and Electric Company, Sollers Point SNG Plant, Sollers Point, Baltimore County, Maryland. Final environmental impact statement

Energy Technology Data Exchange (ETDEWEB)

Liverman, James L.

1978-04-01

An allocation of naphtha feedstock up to 2,186,000 barrels per year to Baltimore Gas and Electric Company (BG and E) to operate its synthetic natural gas (SNG) facility is being considered. The allocation would enable BG and E to produce 10,800,000 mcf of SNG during a 180 day period. Operation of the plant at design capacity is expected to result in annual pollution emissions as follows: 626.4 tons of sulfur oxides, 168.5 tons of nitrogen oxides and 21.6 tons of particulate matter. Incremental emissions due to plant operations relative to existing emissions in Baltimore County are less than 1%. All Federal and State air quality standards should be met. Treated effluent is to be discharged into the Patapasco River where the environmental impacts are not expected to be significant. The SNG facility has been designed to be in compliance with all applicable Federal, State and local effluent standards. Water consumption requirements of 335,000 gallons per day are not expected to significantly tax the area's water resources. Sound generated by the SNG facility will be inaudible or imperceptible. All other operational impacts on land use, population, visual quality, roadways, community facilities and services and ecological systems were judged to be minimal. Environmental impacts resulting from various alternatives ranging from full allocation through denial of an allocation are discussed.

Practical reporting with Ruby and Rails

CERN Document Server

Berube, David

2008-01-01

Business intelligence and real time reporting mechanisms play a major role in any of today s forward looking business plans. With many of these solutions being moved to the Web, the popular Rails framework and its underlying Ruby language are playing a major role alongside web services in building the reporting solutions of tomorrow. Practical Reporting with Ruby and Rails is the first book to comprehensively introduce this popular framework, guiding readers through a wide ranging array of features. Note this isn t a staid guide to generating traditional reports, but rather it shows you how th

Rail transport systems approach

CERN Document Server

2017-01-01

This book shows how the systems approach is employed by scientists in various countries to solve specific problems concerning railway transport. In particular, the book describes the experiences of scientists from Romania, Germany, the Czech Republic, the UK, Russia, Ukraine, Lithuania and Poland. For many of these countries there is a problem with the historical differences between the railways. In particular, there are railways with different rail gauges, with different signaling and communication systems, with different energy supplies and, finally, with different political systems, which are reflected in the different approaches to the management of railway economies. The book’s content is divided into two main parts, the first of which provides a systematic analysis of individual means of providing and maintaining rail transport. In turn, the second part addresses infrastructure and management development, with particular attention to security issues. Though primarily written for professionals involved...

In-Service Performance and Costs of Methods to Control Urban Rail System Noise

Science.gov (United States)

1979-12-01

This study evaluates the acoustic and economic effectiveness of five methods of controlling wheel/rail noise and vibration on urban rail transit systems, namely: rail grinding, wheel truing, resilient wheels, ring-damped wheels, and welded vs. jointe...

The experimental determination of the relationship between the energising time of the common rail injector and the set fuel quantity and rail pressure

Directory of Open Access Journals (Sweden)

Pietras Dariusz

2017-01-01

Full Text Available The article discusses the issue of experimentally determining the relationship between the energising time of the common rail electromagnetic injector and the set fuel quantity and rail pressure. Experimental studies according to the assumed methodology were made on a test bench enabling the dynamic flow rate measurement of the injector. The fuel system mounted on the test bench was controlled by the laboratory CI engine control unit based on the original concept of one of the authors of the article. The results of the experimental studies have made it possible to determine many of the characteristics of the fuel flow rate depending on the specified rail pressure and the energising time of the injector. An analysis was then performed followed by extrapolation of the obtained results. The data obtained from these analyses are the basis for the development of the energising time control algorithm based on a set fuel quantity and rail pressure.

Getting to High School in Baltimore: Student Commuting and Public Transportation

Science.gov (United States)

Stein, Marc L.; Grigg, Jeffrey; Cronister, Curt; Chavis, Celeste; Connolly, Faith

2017-01-01

This report is the first publication of a multi-year project examining the relationship between student commutes using public transportation and on-time arrival and absenteeism. This report begins to develop a basic understanding of how students commute to high school in Baltimore with a focus on those using public transportation. The report is…

Highway-Rail Crossings Inventory Data

Data.gov (United States)

Department of Transportation — The entire National Highway-Rail Crossing Inventory is available in three separate downloadble files. There is a file of all current Public-at-Grade crossings. There...

Medical education resources initiative for teens program in baltimore: A model pipeline program built on four pillars.

Science.gov (United States)

Mains, Tyler E; Wilcox, Mark V; Wright, Scott M

2016-01-01

Less than 6% of U.S. medical school applicants are African-American. The lack of diversity among physicians, by race as well as other measures, confers a negative impact on the American healthcare system because underrepresented minority (URM) physicians are more likely to practice in underserved communities and deliver more equitable, culturally competent care. MERIT (Medical Education Resources Initiative for Teens) is a nonprofit organization based in Baltimore, Maryland, USA. MERIT prepares URM high school students for health careers by providing a holistic support system for seven consecutive years. The program model, which utilizes weekly Saturday sessions, summer internships, and longitudinal mentoring, is built on four foundational pillars: (1) Ignite the Fire, (2) Illuminate the Path, (3) Create the Toolkit, and (4) Sustain the Desire. Since 2011, MERIT has supported 51 students in the Baltimore City Public School System. For the past two years, 100% (n = 14) of MERIT seniors enrolled in universities, compared to only 20.2% of Baltimore City students overall. While it is too early to know whether MERIT alumni will realize their goals of becoming healthcare professionals, they are currently excelling in universities and over 75% (n = 17) are still planning to pursue graduate degrees in health-related fields. After piloting an effective program model, MERIT now has three key priorities moving forward: (1) Creating a sustainable and thriving organization, (2) increasing the number of scholars the program supports in Baltimore, and (3) expanding MERIT to other cities.

Simulation and Measurement of Wheel on Rail Fatigue and Wear

OpenAIRE

Dirks, Babette

2015-01-01

The life of railway wheels and rails has been decreasing in recent years. This is mainly caused by more traffic and running at higher vehicle speed. A higher speed usually generates higher forces, unless compensated by improved track and vehicle designs, in the wheel-rail contact, resulting in more wear and rolling contact fatigue (RCF) damage to the wheels and rails. As recently as 15 years ago, RCF was not recognised as a serious problem. Nowadays it is a serious problem in many countries a...

Shock and vibration environments for large shipping containers on rail cars and trucks

International Nuclear Information System (INIS)

Magnuson, C.F.; Wilson, L.T.

1977-06-01

The purpose of this study was to provide definitions of shock and vibration environment to which fissile material shipping containers may be exposed during normal shipment by truck and rail cars. The definitions of vibration, shock superimposed on vibration and rail coupling shock result from existing data. The dependence of shock environment, from rail coupling operations, on parameters like cargo weight and shock attenuation couplers was also studied using spring-mass models. These studies show that for rail cars equipped with standard draft gear, the cargo response decreases with increased cargo weight until the springs bottom out. For rail cars equipped with shock attenuation couplers, cargo weight has little effect on cargo response. The study also shows the importance of matching couplers and tiedown stiffnesses to decrease the cargo response. Vibration and shock data samples have been obtained during truck shipment of heavy cargo and the data will be presented in subsequent reports. Similar data need to be obtained for rail shipment of heavy cargo and during rail coupling operations with heavy cargo

Modelling of contact problems involved in ensuring the safety of rail transport

Directory of Open Access Journals (Sweden)

Edward Rydygier

2013-12-01

Full Text Available Background: Mathematical modelling aids diagnostics the track and rolling stock, as it often for technical reasons it is not possible to obtain a complete set of measurement data required to diagnose the rail and wheel deformation caused by the impact of a rail vehicle on the track. The important issue in a railway diagnostics is to study the effects of contact wheel and rail. Diagnostics investigations of track and rolling stock have a fundamental role in ensuring the safety of transport of passengers and goods. The aim of the study presented in the paper was to develop simulation methods of mathematical modelling of the wheel-rail system useful in the diagnostics of the track and a railway vehicle. Methods: In the paper two ways of modelling were presented and discussed. One of these ways is the method which consists in reducing the contact issue to field issue and solving the identification of the field source in 2-D system. Also presented a different method designed on the basis of the methods using one period energy concept. This method is adapted for modelling the dynamics of the contact wheel-rail for the normal force. It has been shown that the developed modelling methods to effectively support the study on the effects of mechanical and thermal of contact wheel-rail and contribute to the safety of operations.  Results and conclusions:  In the case of field sources identifications two specific issues were examined: the issue of rail torsion and the identification of heat sources in the rail due to exposure the rolling contact wheel-rail. In the case of the method using one period energy concept it was demonstrated the usefulness of this method to the study of energy processes in the contact wheel-rail under the normal periodic force. The future direction of research is to establish cooperation with research teams entrusted with the diagnostic measurements of track and rolling stock.  

Used fuel rail shock and vibration testing options analysis

Energy Technology Data Exchange (ETDEWEB)

Ross, Steven B. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Best, Ralph E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Klymyshyn, Nicholas A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Jensen, Philip J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Maheras, Steven J. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-09-25

The objective of the rail shock and vibration tests is to complete the framework needed to quantify loads of fuel assembly components that are necessary to guide materials research and establish a technical basis for review organizations such as the U.S. Nuclear Regulatory Commission (NRC). A significant body of experimental and numerical modeling data exists to quantify loads and failure limits applicable to normal conditions of transport (NCT) rail transport, but the data are based on assumptions that can only be verified through experimental testing. The test options presented in this report represent possible paths for acquiring the data that are needed to confirm the assumptions of previous work, validate modeling methods that will be needed for evaluating transported fuel on a case-by-case basis, and inform material test campaigns on the anticipated range of fuel loading. The ultimate goal of this testing is to close all of the existing knowledge gaps related to the loading of used fuel under NCT conditions and inform the experiments and analysis program on specific endpoints for their research. The options include tests that would use an actual railcar, surrogate assemblies, and real or simulated rail transportation casks. The railcar carrying the cradle, cask, and surrogate fuel assembly payload would be moved in a train operating over rail track modified or selected to impart shock and vibration forces that occur during normal rail transportation. Computer modeling would be used to help design surrogates that may be needed for a rail cask, a cask’s internal basket, and a transport cradle. The objective of the design of surrogate components would be to provide a test platform that effectively simulates responses to rail shock and vibration loads that would be exhibited by state-of-the-art rail cask, basket, and/or cradle structures. The computer models would also be used to help determine the placement of instrumentation (accelerometers and strain gauges

78 FR 52231 - 2013 Temporary Closure of I-395 Just South of Conway Street in the City of Baltimore to Vehicular...

Science.gov (United States)

2013-08-22

..., will remain open during the time period of the event. There are five additional I-95 interchanges, just... Temporary Closure of I-395 Just South of Conway Street in the City of Baltimore to Vehicular Traffic To... Transportation Authority (MDTA) to temporarily close a portion of I-395 (just south of Conway Street in Baltimore...

76 FR 77716 - Alternate Passenger Rail Service Pilot Program

Science.gov (United States)

2011-12-14

...-0108; Notice No. 2] RIN 2130-AC19 Alternate Passenger Rail Service Pilot Program AGENCY: Federal... rule is in response to a statutory mandate that FRA complete a rulemaking proceeding to develop a pilot... enactment of the Passenger Rail Investment and Improvement Act of 2008. The final rule develops this pilot...

Rail deployment and storage procedure and test for ITER blanket remote maintenance

International Nuclear Information System (INIS)

Kakudate, S.; Shibanuma, K.

2003-01-01

A concept of rail-mounted vehicle manipulator system has been developed to apply to the maintenance of the ITER blanket composed of ∼400 modules in the vacuum vessel. The most critical issue of the vehicle manipulator system is the feasibility of the deployment and storage of the articulated rail, composed of eight rail links without any driving mechanism in the joints. To solve this issue, a new driving mechanism and procedure for the rail deployment and storage has been proposed, taking account of the repeated operation of the multi-rail links deployed and stored in the same kinematical manner. The new driving mechanism, which is different from those of a usual articulated manipulator or 'articulated boom' equipped with actuators in every joint for movement, is composed of three external mechanisms installed outside the articulated rail, i.e. a vehicle traveling mechanism as main driver and two auxiliary driving mechanisms. A simplified synchronized control of three driving mechanisms has also been proposed, including 'torque-limit control' for suppression of the overload of the mechanisms. These proposals have been tested using a full-scale vehicle manipulator system, in order to demonstrate the proof of principle for rail deployment and storage. As a result, the articulated rail has been successfully deployed and stored within 6 h each, less than the target of 8 h, by means of the three external driving mechanisms and the proposed synchronized control. In addition, the overload caused by an unexpected mismatch of the synchronized control of three driving mechanisms has also been successfully suppressed less than the rated torque by the proposed 'torque-limit control'. It is therefore concluded that the feasibility of the rail deployment and storage of the vehicle manipulator system has been demonstrated

Optimal energy management of urban rail systems: Key performance indicators

International Nuclear Information System (INIS)

González-Gil, A.; Palacin, R.; Batty, P.

2015-01-01

Highlights: • An overall picture of urban rail energy use is provided. • Performance indicators are developed for urban rail system energy optimisation. • A multi-level methodology for assessing energy efficiency measures is presented. - Abstract: Urban rail systems are facing increasing pressure to minimise their energy consumption and thusly reduce their operational costs and environmental impact. However, given the complexity of such systems, this can only be effectively achieved through a holistic approach which considers the numerous interdependences between subsystems (i.e. vehicles, operations and infrastructure). Such an approach requires a comprehensive set of energy consumption-related Key Performance Indicators (KEPIs) that enable: a multilevel analysis of the actual energy performance of the system; an assessment of potential energy saving strategies; and the monitoring of the results of implemented measures. This paper proposes an original, complete list of KEPIs developed through a scientific approach validated by different stakeholders. It consists of a hierarchical list of 22 indicators divided into two levels: 10 key performance indicators, to ascertain the performance of the whole system and complete subsystems; and 12 performance indicators, to evaluate the performance of single units within subsystems, for example, a single rail vehicle or station. Additionally, the paper gives a brief insight into urban rail energy usage by providing an adequate context in which to understand the proposed KEPIs, together with a methodology describing their application when optimising the energy consumption of urban rail systems

Comparison of experimental and theoretical reaction rail currents, rail voltages, and airgap fields for the linear induction motor research vehicle

Science.gov (United States)

Elliott, D. G.

1977-01-01

Measurements of reaction rail currents, reaction rail voltages, and airgap magnetic fields in tests of the Linear Induction Motor Research Vehicle (LIMRV) were compared with theoretical calculations from the mesh/matrix theory. It was found that the rail currents and magnetic fields predicted by the theory are within 20 percent of the measured currents and fields at most motor locations in most of the runs, but differ by as much as a factor of two in some cases. The most consistent difference is a higher experimental than theoretical magnetic field near the entrance of the motor and a lower experimental than theoretical magnetic field near the exit. The observed differences between the theoretical and experimental magnetic fields and currents do not account for the differences of as much as 26 percent between the theoretical and experimental thrusts.

Energy efficiency and reliability solutions for rail operations and facilities.

Science.gov (United States)

2014-11-01

The objectives of the study included examining energy consumption of : the facilities comprising the three major rail yards on the New Haven Rail Line as : well as platform stations and identifying energy efficiency and cost savings : opportunities f...

Rail-suicide prevention: Systematic literature review of evidence-based activities.

Science.gov (United States)

Barker, Emma; Kolves, Kairi; De Leo, Diego

2017-09-01

Rail-related suicide is a relatively rare but extremely lethal method of suicide that can have far-reaching consequences. The aim of the systematic literature review was to analyze the existing literature on the effectiveness of rail-suicide prevention activities. Databases used were Scopus, Medline, and ProQuest. The search terms used were "suicid*," "prevent*," "rail*," or "train." English-language studies published in peer-reviewed journals between 1 January 1990 and 30 April 2015 that presented an overview of rail-related suicide prevention activities and included an analysis of effectiveness were used. We retrieved 1,229 results in the original search with nine papers presenting empirical evidence. Three studies in the review analyzed the effectiveness of platform screen doors and another three analyzed the installation of blue lights, two papers analyzed the effectiveness of suicide pits, and one included the influence of media reporting guidelines. Platform screen doors, suicide pits, blue lights, and improved media guidelines all have the potential to reduce rail-related suicide events and deaths. The review was restricted to English-language peer-reviewed papers published within the chosen time period. © 2016 John Wiley & Sons Australia, Ltd.

Property values, parks, and crime: a hedonic analysis in Baltimore, MD

Science.gov (United States)

Austin Troy; J. Morgan Grove

2008-01-01

While urban parks are generally considered to be a positive amenity, past research suggests that some parks are perceived as a neighborhood liability. Using hedonic analysis of property data in Baltimore, MD, we attempted to determine whether crime rate mediates how parks are valued by the housing market. Transacted price was regressed against park proximity, area-...

A long view of polluting industry and environmental justice in Baltimore

Science.gov (United States)

Christopher G. Boone; Michail Fragkias; Geoffrey L. Buckley; J. Morgan. Grove

2014-01-01

This study examines the density of polluting industry by neighborhoods in Baltimore over the long term, from 1950 to 2010, to determine if high pollution burdens correspond spatially with expected demographic and housing variables predicted in the environmental justice literature. For 1960-1980 we use data on heavy industry from Dun and Bradstreet directories and for...

Laser vibrometer measurement of guided wave modes in rail track

CSIR Research Space (South Africa)

Loveday, PW

2014-11-01

Full Text Available ) in the laboratory and on an operational rail track (with S-4 60-SAR profile) and example results are presented in this section. The measurements 5 were performed using a Polytec PSV-400-M2-20 high frequency scanning vibrometer 6 equipped with the VD-09 velocity...Hz on operational rail track and to identify the modes that are capable of 16 propagating large distances. 17 18 KEYWORDS: Semi-analytical finite element method; modes of guided wave 19 propagation; laser vibrometer measurement; rail track 20 PACs...

Causal analysis of passenger train accidents on freight rail corridors.

Science.gov (United States)

2013-11-01

A number of economic, technical and political factors have limited the development of new, dedicated, very-high-speed rail systems in North America. Consequently, most, near-term development of improved or expanded passenger rail service in the U.S. ...

Energy study of rail passenger transportation. Volume 2. Description of operating systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Henderson, C.; Ellis, H. T.; Wilhelm, J. P.

1979-08-01

The rail passenger systems of the US are described in terms of selected physical, operating, and economic characteristics, and relates services rendered to energy usage and costs. Rail passenger transportation exists in 4 distinct forms: intercity railroads, suburban railroads, heavy-rail transit, and light-rail transit. Each form varies in technical equipment, design of facilities, operating practices, size of systems. Specific data for the national rail passenger network and the Boston, Chicago, Cleveland, New York, Philadelphia, Pittsburgh, and San Francisco regions and the Washington Metropolitan area transit authority are presented.

The ABCs of Keeping on Track to Graduation: Research Findings from Baltimore

Science.gov (United States)

Mac Iver, Martha Abele; Messel, Matthew

2013-01-01

This study of graduation outcomes in Baltimore uses multivariate analysis of longitudinal student cohort data to examine the impact of factors identified in previous research as early warning indicators of a dropout outcome. Student cohort files were constructed from longitudinal administrative data (following all first-time 2004-2005 and…

Study on Rail Profile Optimization Based on the Nonlinear Relationship between Profile and Wear Rate

Directory of Open Access Journals (Sweden)

Jianxi Wang

2017-01-01

Full Text Available This paper proposes a rail profile optimization method that takes account of wear rate within design cycle so as to minimize rail wear at the curve in heavy haul railway and extend the service life of rail. Taking rail wear rate as the object function, the vertical coordinate of rail profile at range optimization as independent variable, and the geometric characteristics and grinding depth of rail profile as constraint conditions, the support vector machine regression theory was used to fit the nonlinear relationship between rail profile and its wear rate. Then, the profile optimization model was built. Based on the optimization principle of genetic algorithm, the profile optimization model was solved to achieve the optimal rail profile. A multibody dynamics model was used to check the dynamic performance of carriage running on optimal rail profile. The result showed that the average relative error of support vector machine regression model remained less than 10% after a number of training processes. The dynamic performance of carriage running on optimized rail profile met the requirements on safety index and stability. The wear rate of optimized profile was lower than that of standard profile by 5.8%; the allowable carrying gross weight increased by 12.7%.

Rail Trails and Property Values: Is There an Association?

Science.gov (United States)

Hartenian, Ella; Horton, Nicholas J.

2015-01-01

The Rail Trail and Property Values dataset includes information on a set of n = 104 homes which sold in Northampton, Massachusetts in 2007. The dataset provides house information (square footage, acreage, number of bedrooms, etc.), price estimates (from Zillow.com) at four time points, location, distance from a rail trail in the community, biking…

A new solution method for wheel/rail rolling contact.

Science.gov (United States)

Yang, Jian; Song, Hua; Fu, Lihua; Wang, Meng; Li, Wei

2016-01-01

To solve the problem of wheel/rail rolling contact of nonlinear steady-state curving, a three-dimensional transient finite element (FE) model is developed by the explicit software ANSYS/LS-DYNA. To improve the solving speed and efficiency, an explicit-explicit order solution method is put forward based on analysis of the features of implicit and explicit algorithm. The solution method was first applied to calculate the pre-loading of wheel/rail rolling contact with explicit algorithm, and then the results became the initial conditions in solving the dynamic process of wheel/rail rolling contact with explicit algorithm as well. Simultaneously, the common implicit-explicit order solution method is used to solve the FE model. Results show that the explicit-explicit order solution method has faster operation speed and higher efficiency than the implicit-explicit order solution method while the solution accuracy is almost the same. Hence, the explicit-explicit order solution method is more suitable for the wheel/rail rolling contact model with large scale and high nonlinearity.

Deviation rectification for dynamic measurement of rail wear based on coordinate sets projection

International Nuclear Information System (INIS)

Wang, Chao; Ma, Ziji; Li, Yanfu; Liu, Hongli; Zeng, Jiuzhen; Jin, Tan

2017-01-01

Dynamic measurement of rail wear using a laser imaging system suffers from random vibrations in the laser-based imaging sensor which cause distorted rail profiles. In this paper, a simple and effective method for rectifying profile deviation is presented to address this issue. There are two main steps: profile recognition and distortion calibration. According to the constant camera and projector parameters, efficient recognition of measured profiles is achieved by analyzing the geometric difference between normal profiles and distorted ones. For a distorted profile, by constructing coordinate sets projecting from it to the standard one on triple projecting primitives, including the rail head inner line, rail waist curve and rail jaw, iterative extrinsic camera parameter self-compensation is implemented. The distortion is calibrated by projecting the distorted profile onto the x – y plane of a measuring coordinate frame, which is parallel to the rail cross section, to eliminate the influence of random vibrations in the laser-based imaging sensor. As well as evaluating the implementation with comprehensive experiments, we also compare our method with other published works. The results exhibit the effectiveness and superiority of our method for the dynamic measurement of rail wear. (paper)

Deviation rectification for dynamic measurement of rail wear based on coordinate sets projection

Science.gov (United States)

Wang, Chao; Ma, Ziji; Li, Yanfu; Zeng, Jiuzhen; Jin, Tan; Liu, Hongli

2017-10-01

Dynamic measurement of rail wear using a laser imaging system suffers from random vibrations in the laser-based imaging sensor which cause distorted rail profiles. In this paper, a simple and effective method for rectifying profile deviation is presented to address this issue. There are two main steps: profile recognition and distortion calibration. According to the constant camera and projector parameters, efficient recognition of measured profiles is achieved by analyzing the geometric difference between normal profiles and distorted ones. For a distorted profile, by constructing coordinate sets projecting from it to the standard one on triple projecting primitives, including the rail head inner line, rail waist curve and rail jaw, iterative extrinsic camera parameter self-compensation is implemented. The distortion is calibrated by projecting the distorted profile onto the x-y plane of a measuring coordinate frame, which is parallel to the rail cross section, to eliminate the influence of random vibrations in the laser-based imaging sensor. As well as evaluating the implementation with comprehensive experiments, we also compare our method with other published works. The results exhibit the effectiveness and superiority of our method for the dynamic measurement of rail wear.

Delphi's new direct acting common rail injection system; Das neue Direct Acting Common Rail System von Delphi

Energy Technology Data Exchange (ETDEWEB)

Schoeppe, Detlev; Zuelch, Stefan; Geurts, Derk; Gris, Christian; Jorach, Rainer W. [Delphi Diesel Systems, Europe (United Kingdom)

2009-07-01

With the serial start of the Direct Acting Common Rail injection system with 2.000 bar Delphi Diesel Systems could supplement its product portfolio with a valuable component. In Delphi's directly propelled Common Rail injector, the Injection needle directly is set in operation with the help of a piezo-ceramic actuator instead of only controlling this with a conventional servo-hydraulic circuit indirectly. This enables a fast opening and closing of the nozzle needle possible independently from the rail pressure. The process of injection is controllable accurately at any time with the again developed two-stage needle movement amplifier. The additionally in the injector integrated fuel storage works as a 'Rail in the Injector' and improves the quality particularly during multiple injection. The injector completely works leakage-free and thereby helps to reach the future CO{sub 2} targets. The use of piezo-actuators as driving force behind the directly working injector leads to a set of requirements to the electronics. A control electronics was developed in order to head optimally the Direct Acting Injector. The sum of all advantages of the Direct Acting of CR systems enables lowest emissions with simultaneously small fuel consumption while new dimensions are reached with power density and engine torque. The authors of the contribution under consideration report on the construction, on the work principle of the Direct Acting CR system and on its performance characteristics as a basis for the premium diesel engine.

75 FR 51158 - BDB Company-Acquisition Exemption-Consolidated Rail Corporation

Science.gov (United States)

2010-08-18

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35398] BDB Company--Acquisition Exemption--Consolidated Rail Corporation BDB Company (BDB), a noncarrier, has filed a verified notice of exemption under 49 CFR 1150.31 to acquire from Consolidated Rail Corporation a parcel of land...

Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

International Nuclear Information System (INIS)

Williams, L.D.; Hall, R.J.

1976-07-01

Results are summarized of the risk assessments of shipping PuO 2 powder and liquid Pu nitrate by truck and rail in the U.S. In the analysis method used, the system is described, potential release sequences are identified and evaluated (fault tree used), and the system risk is assessed. It is concluded that: there is little difference in risk in shipping PuO 2 by rail and by truck; there also is little change in risk in shipping PuO 2 by rail and by truck; there also is little change in risk for liquid shipment; the vermiculite loss is somewhat less important in rail shipment; and the response of the L-10 container to crush is more important in rail transport

The economic effects of high speed rail investment

OpenAIRE

de Rus, Ginés

2008-01-01

The allocation of traffic between different transport modes follows transport user decisions which depend on the generalized cost of travel in the available alternatives. High Speed Rail (HSR) investment is a government decision with significant effects on the generalized cost of rail transport; and therefore on the modal split in corridors where private operators compete for traffic and charge prices close to total producer costs (infrastructure included). The rationale for HSR investment is...

A Preliminary Review of Fatigue Among Rail Staff

OpenAIRE

Jialin Fan; Andrew P. Smith

2018-01-01

Background: Fatigue is a severe problem in the rail industry, which may jeopardize train crew's health and safety. Nonetheless, a preliminary review of all empirical evidence for train crew fatigue is still lacking. The aim of the present paper is, therefore, to provide a preliminary description of occupational fatigue in the rail industry. This paper reviews the literature with the research question examining the risk factors associated with train crew fatigue, covering both papers published...

Surface crack formation on rails at grinding induced martensite white etching layers

DEFF Research Database (Denmark)

Rasmussen, Carsten Jørn; Fæster, Søren; Dhar, Somrita

2017-01-01

The connection between profile grinding of rails, martensite surface layers and crack initiation has been investigated using visual inspection, optical microscopy and 3D X-ray computerized tomography. Newly grinded rails were extracted and found to be covered by a continuous surface layer...... of martensite with varying thickness formed by the grinding process. Worn R350HT and R200 rails were extracted from the Danish rail network as they had transverse bands resembling grinding marks on the running surface. The transverse bands were shown to consist of martensite which had extensive crack formation...... at the martensite/pearlite interface. The cracks in R350HT propagated down into the rail while those in the soft R200 returned to the surface causing only very small shallow spallation. The transverse bands had the same shape, size, orientation, location and periodicity which would be expected from grinding marks...

Lagrangian Sampling of 3-D Air Quality Model Results for Regional Transport Contributions to Sulfate Aerosol Concentrations at Baltimore, MD in Summer of 2004

Science.gov (United States)

The Lagrangian method provides estimates of the chemical and physical evolution of air arriving in the daytime boundary layer at Baltimore. Study results indicate a dominant role for regional transport contributions of those days when sulfate air pollution is highest in Baltimor...

California Dreams in Southeast Baltimore: Using Technology in a Challenging School Setting.

Science.gov (United States)

Slekar, Timothy D.

2000-01-01

Provides an example of how two teachers in the Baltimore (Maryland) City Schools utilized the Internet to help students make a connection with their community. Describes a unit that focuses on the use of Tupac Shakur's rap "California Dream" in order to motivate the students to take pride in their community. (CMK)

75 FR 31511 - Ideal Federal Savings Bank, Baltimore, MD; Approval of Conversion Application

Science.gov (United States)

2010-06-03

... DEPARTMENT OF THE TREASURY Office of Thrift Supervision [AC-46: OTS No. 08283] Ideal Federal Savings Bank, Baltimore, MD; Approval of Conversion Application Notice is hereby given that on May 24, 2010, the Office of Thrift Supervision approved the application of Ideal Federal Savings Bank...

77 FR 11434 - Safety Zone; Patapsco River, Northwest and Inner Harbors, Baltimore, MD

Science.gov (United States)

2012-02-27

...-AA00 Safety Zone; Patapsco River, Northwest and Inner Harbors, Baltimore, MD AGENCY: Coast Guard, DHS... intended route immediately prior to, during, and following the scheduled towing evolution, vessel traffic... made to the maritime community via marine information broadcasts so mariners may adjust their plans...

Depredation of the California Ridgway’s rail: Causes and distribution

Science.gov (United States)

Casazza, Michael L.; Overton, Cory T.; Bui, Thuy-Vy D.; Takekawa, John Y.; Merritt, Angela M.; Hull, J.M.

2016-01-01

We studied the causes of mortality for the California Ridgway’s rail at multiple tidal marshes in the San Francisco Bay Estuary, California. We radio-marked 196 individual rails and examined the evidence from 152 recovered California Ridgway’s rail mortalities from our radio-marked sample and determined plausible cause of death from a wide array of evidence. We also included 10 additional California Ridgway’s rail mortalities (unmarked) that we encountered during our normal field operations. We assigned a likely cause of death to 130 of the recoveries, of which 127 were determined to be caused by predation. Of those, 103 could be divided into class of cause (avian or mammalian), and avian predators were responsible for 64% of those events. Primary predators identified include domestic or feral cats, red fox, owl, and northern harrier. We did find seasonal differences between avian and mammalian predation rates, with higher proportions of avian predation in the winter and early spring. Time of day and tide height

The syphilis elimination project: targeting the Hispanic community of Baltimore city.

Science.gov (United States)

Endyke-Doran, Cara; Gonzalez, Rosa Maria; Trujillo, Marangellie; Solera, Angelo; Vigilance, Pierre N; Edwards, Lori A; Groves, Sara L

2007-01-01

The objective of the Syphilis Elimination Project was to decrease the incidence of syphilis in the Hispanic community of Baltimore City through a culturally appropriate health initiative. Both qualitative and quantitative methods were used in the study design. Surveillance data were used to collect testing information. Comparisons at the start and end of the project measured change in individual knowledge about syphilis. Cross-sectional data from interviews with business owners and qualitative comments from outreach workers evaluated perception of program effectiveness. The local health department collected surveillance data. A convenience sample of 63 Hispanic community members, 12 business owners/managers, and 8 outreach workers was utilized throughout the evaluation process. The project was a culturally appropriate approach to health promotion with street and business outreach. Post intervention there was a statistically significant increase in knowledge about syphilis within the Hispanic community and an increase in testing behaviors. The Syphilis Elimination Project was created in response to a marked increase in syphilis in Baltimore among the Hispanic population and a health disparity that existed within the city. It increased community members' knowledge of syphilis and positively influenced testing behaviors.

Effects of anchoring and arc structure on the control authority of a rail plasma actuator

International Nuclear Information System (INIS)

Choi, Young-Joon; Gray, Miles; Sirohi, Jayant; Raja, Laxminarayan L

2017-01-01

Experiments were conducted on a rail plasma actuator (RailPAc) with different electrode cross sections (rails or rods) to assess methods to improve the actuation authority, defined as the impulse generated for a given electrical input. The arc was characterized with electrical measurements and high-speed images, while impulse measurements quantified the actuation authority. A RailPAc power supply capable of delivering  ∼1 kA of current at  ∼100 V was connected to rod electrodes (free-floating with circular cross-section) and rail electrodes (flush-mounted in a flat plate with rectangular cross-section). High-speed images show that the rail electrodes cause the arc to anchor itself to the anode electrode and transit in discrete jumps, while rod electrodes permit the arc to transit smoothly without anchoring. The impulse measurements reveal that the anchoring reduces the actuation authority by  ∼21% compared to a smooth transit, and the effect of anchoring can be suppressed by reducing the gap between the rails to 2 mm. The study further demonstrates that if a smooth transit is achieved, the control authority can be increased with a larger gap and larger arc current. In conclusion, the actuation authority of a RailPAc can be maximized by carefully choosing a gap width that prevents anchoring. Further study is warranted to increase the RailPAc actuation authority by introducing multiple turns of wires beneath the RailPAc to augment the induced magnetic field. (paper)

Development of rail access to the proposed repository site at Yucca Mountain

International Nuclear Information System (INIS)

Standish, P.N.; Seidler, P.E.; Andrews, W.B.; Shearin, G.

1991-01-01

In accordance with the Nuclear Waste Policy Amendment Act of 1987, Yucca Mountain was designated as the initial site to be investigated as a potential repository for the disposal of high-level radioactive waste. The Yucca Mountain site is an undeveloped area located on the southwestern edge of the Nevada Test Site (NTS), about 100 miles northwest of Las Vegas. The site currently lacks rail service or an existing right-of-way. If the Yucca Mountain site is found suitable for the repository, rail service is considered desirable by the Office of Civilian Radioactive Waste Management (OCRWM) program because of the potential of rail transportation to reduce (1) costs and (2) number of shipments, relative to highway transportation. Therefore, it is necessary to conduct a study to determine (1) that there are alignments for a potential rail line from existing mainline railroads to Yucca Mountain and (2) that these are consistent with present rail design standards and are acceptable relative to environmental and land access considerations

Bubble propagation on a rail: a concept for sorting bubbles by size

Science.gov (United States)

Franco-Gómez, Andrés; Thompson, Alice B.; Hazel, Andrew L.; Juel, Anne

We demonstrate experimentally that the introduction of a rail, a small height constriction, within the cross-section of a rectangular channel could be used as a robust passive sorting device in two-phase fluid flows. Single air bubbles carried within silicone oil are generally transported on one side of the rail. However, for flow rates marginally larger than a critical value, a narrow band of bubble sizes can propagate (stably) over the rail, while bubbles of other sizes segregate to the side of the rail. The width of this band of bubble sizes increases with flow rate and the size of the most stable bubble can be tuned by varying the rail width. We present a complementary theoretical analysis based on a depth-averaged theory, which is in qualitative agreement with the experiments. The theoretical study reveals that the mechanism relies on a non-trivial interaction between capillary and viscous forces that is fully dynamic, rather than being a simple modification of capillary static solutions.

Parking Space Occupancy at Rail Stations in Klang Valley

Directory of Open Access Journals (Sweden)

Ho Phooi Wai

2017-01-01

Full Text Available The development of Klang Valley Integrated Rapid Transit system in Klang Valley, Malaysia has been quickly gaining momentum during the recent years. There will be two new MRT lines (MRT Line 1 and MRT Line 2 and one new LRT line (LRT Line 3 extended from the current integrated rail transit system by year 2020 with more than 90 new rail stations. With the substantial addition of potential rail passengers, there are doubts whether the existing Park and Ride facilities in Klang Valley are able to accommodate the future parking space demand at rail stations. This research studies the parking occupancy at various Park and Ride facilities in Klang Valley namely Taman Jaya, Asia Jaya, Taman Paramount, Taman Bahagia and Kelana Jaya by applying the non-conventional method utilizing Google Earth imageries. Results showed that the parking occupancy rate at these LRT stations were 100% or more before the commencement of LRT extension (Kelana Jaya and Ampang Lines in 2016 and in the range of 36% to 100% after the commencement of LRT extension due to the additionally built car parks and changes in parking pattern with dispersed passenger traffic.

How can a successful multi-family residential recycling programme be initiated within Baltimore City, Maryland?

Science.gov (United States)

Schwebel, Michael B

2012-07-01

Baltimore City formally began recycling in 1989 with all neighbourhoods having residential collection by 1992. Although the city of 637 000 has recycled for approximately 20 years, almost all residents in multi-family residential (MFR) housing have been and are still barred from participating at their residences. Discussions with City officials and residents have verified this antiquated policy of exclusion within MFR housing. Yet, the policy is still observed by the Department of Public Works even though the updated single-stream Code states that the 'Director of Public Works must collect all. . .recyclable materials. . .from all dwellings, including multiple-family dwellings'. The purpose of this study's is to provide policies, regulations, and recommendations for implementing requisite MFR recycling within Baltimore City. The study's methodology follows a case study approach by examining three cities in the United States that currently mandate MFR recycling: Chicago, Illinois; Boston, Massachusetts; and Arlington, Virginia. Post-analysis suggests that while some cities' MFR programmes perform poorly, each city's strengths aid in creating specific proposals that can produce a successful MFR recycling program in Baltimore City. These tenets of a future MFR recycling program form the basis of a successful MFR recycling program that will allow all city residents to participate via initiatives in the categories of both programme, accessibility, and informing and self-review.

BIM Interoperability Limitations: Australian and Malaysian Rail Projects

Directory of Open Access Journals (Sweden)

Kenley Russell

2016-01-01

Full Text Available Building information modelling (BIM is defined as a process involving the generation and management of digital representation of physical and functional characteristics of a facility. The purpose of interoperability in integrated or “open” BIM is to facilitate the information exchange between different digital systems, models and tools. There has been effort towards data interoperability with development of open source standards and object-oriented models, such as industry foundation classes (IFC for vertical infrastructure. However, the lack of open data standards for the information exchange for horizontal infrastructure limits the adoption and effectiveness of integrated BIM. The paper outlines two interoperability issues for construction of rail infrastructure. The issues are presented in two case study reports, one from Australia and one from Malaysia. The each case study includes: a description of the project, the application of BIM in the project, a discussion of the promised BIM interoperability solution plus the identification of the unresolved lack of interoperability for horizontal infrastructure project management. The Moreton Bay Rail project in Australia introduces general software interoperability issues. The Light Rail Extension project in Kuala Lumpur outlines an example of the integration problems related to two different location data structures. The paper highlights how the continuing lack of data interoperability limits utilisation of integrated BIM for horizontal infrastructure rail projects.

Evaluating the attractiveness of a new light rail extension: Testing simple change and displacement change hypotheses.

Science.gov (United States)

Werner, Carol M; Brown, Barbara B; Tribby, Calvin P; Tharp, Doug; Flick, Kristi; Miller, Harvey J; Smith, Ken R; Jensen, Wyatt

2016-01-01

Many communities in the United States have been adding new light rail to bus-predominant public transit systems. However, there is disagreement as to whether opening light rail lines attracts new ridership or merely draws ridership from existing transit users. We study a new light rail line in Salt Lake City, Utah, USA, which is part of a complete street redevelopment. We utilize a pre-test post-test control group quasi-experimental design to test two different measures of ridership change. The first measure is calculated from stops along the light rail route; the second assumes that nearby bus stops might be displaced by the rail and calculates ridership change with those stops included as baseline. Both the simple measure (transit use changes on the complete street light rail corridor) and the "displacement" measure (transit use changes in the one-quarter mile catchment areas around new light rail stops) showed significant ( p rail bus users. In particular, the displacement analysis discredits a common challenge that when a new light rail line opens, most passengers are simply former bus riders whose routes were canceled in favor of light rail. The study suggests that light rail services can attract additional ridership to public transit systems. In addition, although pre-post control-group designs require time and effort, this project underscores the benefits of such quasi-experimental designs in terms of the strength of the inferences that can be drawn about the impacts of new transit infrastructure and services.

Social exclusion and high speed rail: The case study of Spain

Energy Technology Data Exchange (ETDEWEB)

Pagliara, F.; Menicocci, F.; Vassallo, J.M.; Gomez, J.

2016-07-01

Very few contributions in the literature have dealt with the issue of social exclusion related to High Speed Rail systems. The objective of this manuscript is to understand what are the factors excluding users from choosing High Speed Rail services considering as case study Spain. For this purpose, a Revealed Preference survey was employed in November and December 2015. A questionnaire was submitted to users of the Spanish transport systems travelling for long distance-journeys. The aim was that of investigating their perception of High Speed Rail system and the factors inhibiting passengers or excluding them from its use. Data about their socioeconomic characteristics were collected as well. The main result of the survey has been that a relationship between social exclusion and High Speed Rail in Spain is present, especially in terms of geographical exclusion. (Author)

USDOE Top-of-Rail Lubricant Project; FINAL

International Nuclear Information System (INIS)

Mohumad F. Alzoubi; George R. Fenske; Robert A. Erck; Amrit S. Boparai

2002-01-01

Lubrication of wheel/rail systems has been recognized for the last two decades as a very important issue for railroads. Energy savings and less friction and wear can be realized if a lubricant can be used at the wheel/rail interface. On the other hand, adverse influences are seen in operating and wear conditions if improper or excessive lubrication is used. Also, inefficiencies in lubrication need to be avoided for economic and environmental reasons. The top-of-rail (TOR) lubricant concept was developed by Texaco Corporation to lubricate wheels and rails effectively and efficiently. Tranergy Corporation has been developing its SENTRAEN 2000(trademark) lubrication system for the last ten years, and this revolutionary new high-tech on-board rail lubrication system promises to dramatically improve the energy efficiency, performance, safety, and track environment of railroads. The system is fully computer-controlled and ensures that all of the lubricant is consumed as the end of the train passes. Lubricant quantity dispensed is a function of grade, speed, curve, and axle load. Tranergy also has its LA4000(trademark) wheel and rail simulator, a lubrication and traction testing apparatus. The primary task of this project was collecting and analyzing the volatile and semivolatile compounds produced as the lubricant was used. The volatile organic compounds were collected by Carbotrap cartridges and analyzed by adsorption and gas chromatography/mass spectrometry (GC/MS). The semivolatile fraction was obtained by collecting liquid that dripped from the test wheel. The collected material was also analyzed by GC/MS. Both of these analyses were qualitative. The results indicated that in the volatile fraction, the only compounds on the Environmental Protection Agency's (EPA) Superfund List of Analytes detected were contaminants either in the room air or from other potential contamination sources in the laboratory. Similarly, in the semivolatile fraction none of the detected

South Africa’s freight rail reform: A demand-driven perspective

Directory of Open Access Journals (Sweden)

Jan H. Havenga

2014-11-01

Full Text Available During the 20th century, freight transport in South Africa was employed to attain politicoeconomic ideals, resulting in the overprotection of rail and overregulation of road transport. Increasing industry pressure, combined with the international deregulation trend, led to deregulation in 1988. Myopia resulted in a rail investment hiatus and exponential growth in high-value, long-distance road transport, causing excessive logistics and externality costs for the country. The aim of this study was to propose a freight rail reform agenda based on, (1 lessons from past freight transport policy efforts and (2 the results of freight transport market segmentation driven by models developed over the past two decades. For the study, freight flows were modelled by disaggregating the national input–output model into 372 origin–destination pairs and 71 commodity groups, followed by distance decay gravitymodelling. Logistics costs were calculated by relating commodity-level freight flows to the costs of fulfilling associated logistical functions. The standard management approach of founding strategy development on market-driven segmentation provides a neutral input to steer rail reform discussions in South Africa. Market segmentation points to a dualistic rail reform agenda, enabling both a profit-driven core and a development-driven branch line network. Freight flow insights are steering the policy reform debate towards long-term freight strategy development and optimal freight logistics network design.

A Measuring Method About the Bullet Velocity in Electromagnetic Rail Gun

Directory of Open Access Journals (Sweden)

Jianming LIU

2014-02-01

Full Text Available The operating principle of electromagnetic rail gun by store capacitor was analyzed. A simulation model about the bullet velocity in the electromagnetic rail gun was built. The results of computer simulation experiment showed the relationships between the bullet velocity and the capacitor charging voltage and the pellet mass. By ten coil targets, a new kind of measuring method for the bullet velocity in electromagnetic rail gun was presented. The results of the actual experiment were analyzed. The improving method for measuring bullet velocity was put forward.

Tunnel - history of

International Nuclear Information System (INIS)

1998-11-01

This book introduces history of tunnel in ancient times, the middle ages and modern times, survey of tunnel and classification of bedrock like environment survey of position, survey of the ground, design of tunnel on basic thing of the design, and design of tunnel of bedrock, analysis of stability of tunnel and application of the data, construction of tunnel like lattice girder and steel fiber reinforced shot crete, and maintenance control and repair of tunnel.

System diagnosis using finite memory observers: Common Rail application; Diagnostic des systemes a l'aide d'observateurs a memoire finie: application au Common Rail

Energy Technology Data Exchange (ETDEWEB)

Graton, G.

2005-12-15

The aim of this work was to propose a fault detection method on the high pressure direct injection system (called Common Rail system) set up on Diesel vehicles. The importance of the fault detection procedure implementation was highlighted thanks to the description of the stakes (lowers consumption, reduction in the pollutant emissions and sound, increase of performances) and constraints dependent on Common Rail (high pressure, high frequency, gas oil lubrication, high precision machining, standards EURO respect,...) but also through a listing of failures which can occur on Common Rail. A synthesis on the different diagnosis methods of systems contributed to select a fault detection method with expected performances (detection of fault beginning, detection speed, isolation and characterization of detected fault and minimizing false alarm and bad detections). After a detailed study (properties, sequential formulations and sensitivity study) of the selected detection method (finite memory observers) and a modeling of the Common Rail various bodies behavior, the algorithm of detection was tested on three different models of the system Common Rail. Moreover, the comparison between the finite memory observer and a Luenberger observer and a Kalman filter allow to appreciate the residual robustness degree. Obtained results allow to conclude on good detection of actuator and sensor faults. (author)

Investigating the lubricity and electrical insulation caused by sanding in dry wheel–rail contacts

NARCIS (Netherlands)

Arias-Cuevas, O.; Li, Z.; Lewis, R.

2009-01-01

The adhesion (or available friction) in the wheel–rail contact is the most important parameter for the braking and traction operation of rail vehicles. Since the beginning of railway transportation, sanding from the locomotive has been a common practice to enhance the wheel–rail adhesion. In recent

Investigating stakeholders' perceptions of the link between high STD rates and the current Baltimore City Public Schools' sex education curriculum

Science.gov (United States)

Bolden, Shenell L. T.

The purpose of this exploratory study was to examine key stakeholders' perceptions of the current Baltimore City Public Schools' (BCPS) sex education curriculum and to gain insight into how they believe the curriculum could be modified to be more effective. A mixed methods approach using qualitative and quantitative data collection consisting of a survey, focus group interview, and individual interviews was conducted to gather information on stakeholders' perceptions. The stakeholders included: (1) former students who received their sex education courses in the Baltimore City Public School system (BCPS); (2) teachers in BCPS who were affiliated with the sex education curriculum; (3) health care professionals who screened and/or treated East Baltimore City residents for a sexually transmitted disease (STD) and; (4) one policy maker who was responsible for creating sex education curriculum at the national level. Analysis of the quantitative data from former Baltimore City Public School students revealed a general satisfaction with the current sex education curriculum. However, qualitative data from the same group of stakeholders revealed several changes they thought should be implemented into the program in an effort to improve the current curriculum. Findings from the other groups after qualitative analysis of the interviews suggest three major themes in support of curriculum change: (1) a blended curriculum that integrates both the cognitive and affective learning domains; (2) knowledge of prevention of STD's and pregnancy; and (3) authentic teaching and learning. Results from this study strongly suggest that the Baltimore City Public School system is apathetic to the sexual health needs of students and, therefore, is inadvertently contributing to the high rate of sexually transmitted diseases among young people. Keywords: Abstinence, Affective domain, Indoctrination, Behavior Modification, Cognitive domain, Sex education curriculum, Sexually Transmitted Diseases.

Structural analysis of the ITER Divertor toroidal rails

Energy Technology Data Exchange (ETDEWEB)

Viganò, F., E-mail: Fabio.Vigano@LTCalcoli.it [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy); Escourbiac, F.; Gicquel, S.; Komarov, V. [ITER Organization, Route de Vinon sur Verdon, 13115 St. Paul lez Durance (France); Lucca, F. [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy); Merola, M. [ITER Organization, Route de Vinon sur Verdon, 13115 St. Paul lez Durance (France); Ngnitewe, R. [L.T. Calcoli SaS, Piazza Prinetti 26/B, 23807 Merate (Italy)

2013-10-15

The Divertor is one of the most technically challenging components of the ITER machine, which has the main function of extracting the power conducted in the scrape-off layer while maintaining the plasma purity. There are 54 Divertor cassettes installed in the vacuum vessel (VV). Each cassette body (CB) is fastened on the inner and outer concentric Divertor toroidal rails. The comprehensive assessment (in accordance with the Structural Design Criteria for ITER In-vessel Components: ITER SDC-IC) of the Divertor toroidal rails has been performed during design activity based on performing of thermal and stress analyses at operating conditions of neutron stage of ITER operation. This paper outlines the engineering aspects of the ITER Divertor toroidal rails and focuses on some critical regions of the present design highlighted by the performed structural assessment. The structural assessment has been performed with help of using Finite Element (FE) Abaqus code and based on criteria given by ITER SDC-IC.

A REVIEW OF HIGH-SPEED RAIL PLAN IN JAVA ISLAND: A COMPARISON WITH EXISTING MODES OF TRANSPORT

Directory of Open Access Journals (Sweden)

Eko Hartono

2013-05-01

It can be concluded that journey time and fare of the high-speed rail is very competitive to the air transport in Jakarta-Surabaya corridor. The journey time to travel from Jakarta to Surabaya is 4 hours and 19 minutes by high-speed train and 4 hours and 40 minutes by air. Based on the benchmarking analysis, the suitable fare for the high-speed rail should be 70% of the air transport. This study predicted that 61% of air passenger, 18% of conventional rail passenger and 12% of bus passenger will switch to the high-speed rail service in 2020. In total, the high-speed rail will have 24% of market share for the passenger transport and becomes the second largest market share after road transport (52%. The conventional rail and air transport have 14% and 9% of total market share to travel from Jakarta to Surabaya and vice versa. The high-speed rail development reduces carbon emissions caused by transportation systems in Java Island. It has been calculated that there are 2.542 million tonnages of CO2 per annum without introducing high-speed rail, however, the CO2 emissions decrease to 1.694 million tonnages per annum if the high-speed rail is developed in Java Island. Generalized cost of the high-speed rail is higher than road and conventional rail. However, it is lower than air transport. Keywords: Java high-speed rail, HSR Comparison, modal share, journey time

Typical Underwater Tunnels in the Mainland of China and Related Tunneling Technologies

Directory of Open Access Journals (Sweden)

Kairong Hong

2017-12-01

Full Text Available In the past decades, many underwater tunnels have been constructed in the mainland of China, and great progress has been made in related tunneling technologies. This paper presents the history and state of the art of underwater tunnels in the mainland of China in terms of shield-bored tunnels, drill-and-blast tunnels, and immersed tunnels. Typical underwater tunnels of these types in the mainland of China are described, along with innovative technologies regarding comprehensive geological prediction, grouting-based consolidation, the design and construction of large cross-sectional tunnels with shallow cover in weak strata, cutting tool replacement under limited drainage and reduced pressure conditions, the detection and treatment of boulders, the construction of underwater tunnels in areas with high seismic intensity, and the treatment of serious sedimentation in a foundation channel of immersed tunnels. Some suggestions are made regarding the three potential great strait-crossing tunnels—the Qiongzhou Strait-Crossing Tunnel, Bohai Strait-Crossing Tunnel, and Taiwan Strait-Crossing Tunnel—and issues related to these great strait-crossing tunnels that need further study are proposed. Keywords: Underwater tunnel, Strait-crossing tunnel, Shield-bored tunnel, Immersed tunnel, Drill and blast

Shock and vibration environments encountered during normal rail transportation of heavy cargo

International Nuclear Information System (INIS)

Magnuson, C.F.

1982-08-01

This study was conducted to obtain vibration and superimposed shock data during normal rail shipment of heavy cargo. The data were obtained during a regularly scheduled rail shipment of a 45-tonne (50-ton) cargo which consisted of an empty spent-fuel container, its supporting structure, and associated hoisting devices. The shipment was made over rail lines which are operated by the Atchison, Topeka, and Santa Fe Railway Company between Denver, Colorado and Albuquerque, New Mexico. The instrumented rail car was equipped with 0.38-m (15-in.) hydraulic end-of-car coupling devices. The 99 percentile levels of vibration acceleration amplitudes and single degree-of-freedom superimposed shock response spectra for the longitudinal, transverse, and vertical axes are presented

49 CFR 210.29 - Operation standards (moving locomotives and rail cars).

Science.gov (United States)

2010-10-01

... cars). 210.29 Section 210.29 Transportation Other Regulations Relating to Transportation (Continued... REGULATIONS Inspection and Testing § 210.29 Operation standards (moving locomotives and rail cars). The operation standards for the noise emission levels of moving locomotives, rail cars, or consists of...

Ballistic Rail Gun Soft Recovery Facility

Data.gov (United States)

Federal Laboratory Consortium — The Ballistic Rail Gun Soft Recovery Facility accommodates a 155mm Howitzer, fired horizontally into a 104-foot long water trough to slow the projectile and recover...

Rail Baltica tuleb : reisiterminalide arhitektuurivõistlused Tallinnas ja Pärnus = Rail Baltic is coming : Arhitecture competitions for passenger rail terminals in Tallinn and Pärnu / Andres Lindemann

Index Scriptorium Estoniae

Lindemann, Andres

2015-01-01

2014.a. lõpus lõppesid arhitektuurivõistlused Tallinnas Ülemistele ja Pärnus Papiniidu piirkonda plaanitavatele Rail Baltica reisiterminalidele. Artiklis on antud põgus ülevaade võitnud töödest

Research of the Resistance of Contact Welding Joint of R65 Type Rail

Directory of Open Access Journals (Sweden)

Kęstutis Dauskurdis

2015-03-01

Full Text Available In the article the R65 type rail joints that were welded by resistance welding are analysed. Survey methodology of the research consists of the following parts: visual inspection of welded joint, ultrasonic rail inspection, hardness test of upper part of the rail, fusion area research, the measurement hardness test of heat-softened area, the measurement microhardness test, microstructure research of the welded joint, impact strength experiments, chemical analysis of welded joint, wheel-rail interaction research using the finite element method (FEM. The results of the research are analysed and the quality of weld is evaluated. The conclusion is based on the results of this research.

Direct, coherent and incoherent intermediate state tunneling and scanning tunnel microscopy (STM)

International Nuclear Information System (INIS)

Halbritter, J.

1997-01-01

Theory and experiment in tunneling are still qualitative in nature, which hold true also for the latest developments in direct-, resonant-, coherent- and incoherent-tunneling. Those tunnel processes have recently branched out of the field of ''solid state tunnel junctions'' into the fields of scanning tunnel microscopy (STM), single electron tunneling (SET) and semiconducting resonant tunnel structures (RTS). All these fields have promoted the understanding of tunneling in different ways reaching from the effect of coherence, of incoherence and of charging in tunneling, to spin flip or inelastic effects. STM allows not only the accurate measurements of the tunnel current and its voltage dependence but, more importantly, the easy quantification via the (quantum) tunnel channel conductance and the distance dependence. This new degree of freedom entering exponentially the tunnel current allows an unique identification of individual tunnel channels and their quantification. In STM measurements large tunnel currents are observed for large distances d > 1 nm explainable by intermediate state tunneling. Direct tunneling with its reduced tunnel time and reduced off-site Coulomb charging bridges distances below 1 nm, only. The effective charge transfer process with its larger off-site and on-site charging at intermediate states dominates tunnel transfer in STM, biology and chemistry over distances in the nm-range. Intermediates state tunneling becomes variable range hopping conduction for distances larger than d > 2 nm, for larger densities of intermediate states n 1 (ε) and for larger temperatures T or voltages U, still allowing high resolution imaging

19 CFR 123.91 - Electronic information for rail cargo required in advance of arrival.

Science.gov (United States)

2010-04-01

... identification number will be a unique number to be assigned by CBP upon the implementation of the Automated... implementation of the Automated Commercial Environment); (8) The place where the rail carrier takes possession of... being shipped by rail; (10) Container numbers (for containerized shipments) or the rail car numbers; and...

Research on the Common Rail Pressure Overshoot of Opposed-Piston Two-Stroke Diesel Engines

Directory of Open Access Journals (Sweden)

Yi Lu

2017-04-01

Full Text Available The common rail pressure has a direct influence on the working stability of Opposed-Piston Two-Stroke (OP2S diesel engines, especially on performance indexes such as power, economy and emissions. Meanwhile, the rail pressure overshoot phenomenon occurs frequently due to the operating characteristics of OP2S diesel engines, which could lead to serious consequences. In order to solve the rail pressure overshoot problem of OP2S diesel engines, a nonlinear concerted algorithm adding a speed state feedback was investigated. First, the nonlinear Linear Parameter Varying (LPV model was utilized to describe the coupling relationship between the engine speed and the rail pressure. The Linear Quadratic Regulator (LQR optimal control algorithm was applied to design the controller by the feedback of speed and rail pressure. Second, cooperating with the switching characteristics of injectors, the co-simulation of MATLAB/Simulink and GT-Power was utilized to verify the validity of the control algorithm and analyze workspaces for both normal and special sections. Finally, bench test results showed that the accuracy of the rail pressure control was in the range of ±1 MPa, in the condition of sudden 600 r/min speed increases. In addition, the fuel mass was reduced 76.3% compared with the maximum fuel supply quantity and the rail pressure fluctuation was less than 20 MPa. The algorithm could also be appropriate for other types of common rail system thanks to its universality.

Rail Baltica waiting at the station

Index Scriptorium Estoniae

2010-01-01

Majandus- ja kommunikatsiooniministeeriumi transpordi asekantsleri Eero Pärgmäe sõnul on Eesti 2012. aastal valmis Tallinn-Riia rongiliini avamiseks. Tallinn-Berliini rongiliinist. Siim Kallas lubas aidata edendada Rail Baltica projekti

Taanlased pidasid Pärnut läbivat Rail Balticat kalleimaks / Raavo Raadik

Index Scriptorium Estoniae

Raadik, Raavo

2007-01-01

Taani konsultatsioonifirma COWI tutvustas uuringut, milles analüüsiti Balti riike Euroopaga ühendava raudtee Rail Baltica majanduslikku tasuvust ning selle loomiseks vajalike investeeringute mahtu. Kaart: Rail Baltica võimalik teekond Eestis

Rail security : some actions taken to enhance passenger and freight rail security, but significant challenges remain : testimony before the Committee on Commerce, Science, and Transportation, U.S. Senate

Science.gov (United States)

2004-03-23

Passenger and freight rail services are important links in the nation's transportation system. Terrorist attacks on passenger and/or freight rail services have the potential to cause widespread injury, loss of life, and economic disruption. The recen...

Appraisal on Rail Transit Development: A Review on Train Services and Safety

Science.gov (United States)

Nordin, Noor Hafiza binti; Masirin, Mohd Idrus Haji Mohd; Ghazali, Mohd Imran bin; Azis, Mohd Isom bin

2017-08-01

The ever increasing problems faced by population around the world have made demands that transportation need to be improved as an effective and efficient communication means. It is considered as a necessity especially when rapid development and economic growth of a country is the agenda. Among the transportation modes being focused as critical facilities are the bus system, rail system, road network, shipping system and air transportation system. Rail transport is a means of conveyance of passengers and goods by way of wheeled vehicles running on rail tracks. In Malaysia, the railway network has evolved tremendously since its inception in the early 19th century. It has grown proportionally with the national development. Railway network does not only mean for rural transportation, but it also considered as a solution to urban congestion challenges. Currently, urban rail transit is the most popular means of urban transportation system especially as big cities such as Kuala Lumpur. This paper presents the definition of rail transportation system and its role in urban or sub-urban operation. It also describes the brief history of world railway transportation including a discussion on Malaysian rail history perspective. As policy and standard are important in operating a railway system, this paper also illustrates and discusses some elements which have an impact on the effectiveness and efficiency of train operation. Towards the end, this paper also shares the importance of railway safety based on real case studies around the world. Thus, it is hoped that this paper will enable the public to understand the rail transit development and appreciate its existence as a public transportation system.

Reduction of Sleep Deprivation and Fatigue in Mass Transit Rail Operators.

Science.gov (United States)

Haynes, Ajeenah L

2017-08-01

Sleep and work schedules differ considerably between rail workers and the broader U.S. workforce. Due to extended work hours and night shift schedules, train and engine service workers who operate passenger trains or move freight are most vulnerable to fatigue. This article addresses the need for comprehensive fatigue risk management systems (FRMS) for rail operators. Using a transactional ergonomic perspective, FRMS are discussed with a focus on fatigue education and administrative controls to reduce feelings of tiredness, low motivation, poor concentration, and low physical activity among mass transit rail operators. Recommendations for intervention implementation and evaluation are provided.

idRHa+ProMod - Rail Hardening Control System

International Nuclear Information System (INIS)

Ferro, L

2016-01-01

idRHa+ProMod is the process control system developed by Primetals Technologies to foresee the thermo-mechanical evolution and micro-structural composition of rail steels subjected to slack quenching into idRHa+ Rail Hardening equipments in a simulation environment. This tool can be used both off-line or in-line, giving the user the chance to test and study the best cooling strategies or letting the automatic control system free to adjust the proper cooling recipe. Optimization criteria have been tailored in order to determine the best cooling conditions according to the metallurgical requirements imposed by the main rail standards and also taking into account the elastoplastic bending phenomena occurring during all stages of the head hardening process. The computational core of idRHa+ProMod is a thermal finite element procedure coupled with special algorithms developed to work out the main thermo-physical properties of steel, to predict the non-isothermal austenite decomposition into all the relevant phases and subsequently to evaluate the amount of latent heat of transformation released, the compound thermal expansion coefficient and the amount of plastic deformation in the material. Air mist and air blades boundary conditions have been carefully investigated by means of pilot plant tests aimed to study the jet impingement on rail surfaces and the cooling efficiency at all working conditions. Heat transfer coefficients have been further checked and adjusted directly on field during commissioning. idRHa+ is a trademark of Primetals Technologies Italy Srl (paper)

idRHa+ProMod - Rail Hardening Control System

Science.gov (United States)

Ferro, L.

2016-03-01

idRHa+ProMod is the process control system developed by Primetals Technologies to foresee the thermo-mechanical evolution and micro-structural composition of rail steels subjected to slack quenching into idRHa+ Rail Hardening equipments in a simulation environment. This tool can be used both off-line or in-line, giving the user the chance to test and study the best cooling strategies or letting the automatic control system free to adjust the proper cooling recipe. Optimization criteria have been tailored in order to determine the best cooling conditions according to the metallurgical requirements imposed by the main rail standards and also taking into account the elastoplastic bending phenomena occurring during all stages of the head hardening process. The computational core of idRHa+ProMod is a thermal finite element procedure coupled with special algorithms developed to work out the main thermo-physical properties of steel, to predict the non-isothermal austenite decomposition into all the relevant phases and subsequently to evaluate the amount of latent heat of transformation released, the compound thermal expansion coefficient and the amount of plastic deformation in the material. Air mist and air blades boundary conditions have been carefully investigated by means of pilot plant tests aimed to study the jet impingement on rail surfaces and the cooling efficiency at all working conditions. Heat transfer coefficients have been further checked and adjusted directly on field during commissioning. idRHa+ is a trademark of Primetals Technologies Italy Srl

HRTPO strategic campaign and vision plan for passenger rail : phase 1 overview.

Science.gov (United States)

2010-03-17

SUBJECT: : TEMS (Transportation Economics & Management Systems, Inc.), the consultant specializing in : passenger rail planning, was secured by the HRTPO and its partner DRPT to evaluate the potential : passenger rail service alternative defined by t...

76 FR 9407 - Fraternity Federal Savings & Loan Association, Baltimore, MD; Approval of Conversion Application

Science.gov (United States)

2011-02-17

... DEPARTMENT OF THE TREASURY Office of Thrift Supervision [AC-58 OTS No. 01292 and H 4762] Fraternity Federal Savings & Loan Association, Baltimore, MD; Approval of Conversion Application Notice is hereby given that on February 10, 2011, the Office of Thrift Supervision approved the application of...

77 FR 25592 - Safety Zone; Patapsco River, Northwest and Inner Harbors, Baltimore, MD

Science.gov (United States)

2012-05-01

... National Technology Transfer and Advancement Act (NTTAA) (15 U.S.C. 272 note) directs agencies to use... historic sloop-of-war USS CONSTELLATION on May 24, 2012. This action is necessary to provide for the safety...-of-war USS CONSTELLATION in Baltimore, Maryland on May 24, 2012. Planned events include a three- hour...

Review on Malaysian Rail Transit Operation and Management System: Issues and Solution in Integration

Science.gov (United States)

Masirin, Mohd Idrus Mohd; Salin, Aminah Mohd; Zainorabidin, Adnan; Martin, David; Samsuddin, Norshakina

2017-08-01

In any context, operation and management of transportation systems are key issues which may affect both life quality and economic development. In large urban agglomerations, an efficient public transportation system may help abate the negative externalities of private car use such as congestion, air and noise pollution, accident and fuel consumption, without excessively penalizing user travel times or zone accessibility. Thus, this study is conducted to appraise the Malaysian rural rail transit operation and management system, which are considered important as there are many issues and solution in integration of the services that need to be tackled more conscientiously. The purpose of this paper is to describe some of the most important issues on integration of services and rail transit system in Malaysian and how to solve or reduce these problems and conflicts. In this paper, it consists of the historical development of rail transit construction in Malaysia. This paper also attempts to identify the important issues related to rail transit services and integration in Malaysian rural rail operation and management system. Comparison is also conducted with other countries such as UK, France, and Japan. Finally, a critical analysis is presented in this paper by looking at the possible application for future Malaysian rail transit operation system and management, especially focusing on enhancing the quality of Malaysian rural rail transit. In conclusion, this paper is expected to successfully review and appraise the existing Malaysian rural rail transit operation and management system pertaining to issues & solution in integration. It is also hoped that reformation or transformation of present service delivery quality of the rail transit operation and management will enable Malaysia to succeed in transforming Malaysian transportation system to greater heights.

Rail Brake System Using a Linear Induction Motor for Dynamic Braking

Science.gov (United States)

Sakamoto, Yasuaki; Kashiwagi, Takayuki; Tanaka, Minoru; Hasegawa, Hitoshi; Sasakawa, Takashi; Fujii, Nobuo

One type of braking system for railway vehicles is the eddy current brake. Because this type of brake has the problem of rail heating, it has not been used for practical applications in Japan. Therefore, we proposed the use of a linear induction motor (LIM) for dynamic braking in eddy current brake systems. The LIM reduces rail heating and uses an inverter for self excitation. In this paper, we estimated the performance of an LIM from experimental results of a fundamental test machine and confirmed that the LIM generates an approximately constant braking force under constant current excitation. At relatively low frequencies, this braking force remains unaffected by frequency changes. The reduction ratio of rail heating is also approximately proportional to the frequency. We also confirmed that dynamic braking resulting in no electrical output can be used for drive control of the LIM. These characteristics are convenient for the realization of the LIM rail brake system.

Contaminant levels and toxicity of sediments and water of Baltimore Harbor and Back River, Maryland

International Nuclear Information System (INIS)

Logan, D.T.; Jacobs, F.; Mehrotra, N.

1995-01-01

The Patapsco and Back River Watershed drains the Baltimore metropolitan area, Maryland's most heavily industrialized and urbanized region. Due to the intensive development and industrialization of the Baltimore metropolitan area over the past 250 years, high levels of contaminants have been discharged into Baltimore Harbor on the Patapsco River and into the Back River. Pollutants historically discharged include heavy metals, petroleum hydrocarbons, pesticides, cyanide, sewage, other organic chemicals, and nutrients. Sources have included industrial and municipal discharges, sewerage overflows, urban runoff, and leaks and spills from vessels and on-land facilities. The Maryland Department of the Environment undertook this study of ambient conditions as part of a developing strategy to assess and improve conditions in the Chesapeake Bay and its tributaries. Past studies were compiled, evaluated, and synthesized to identify the areas of degraded conditions and contaminants of possible concern. Sediment contaminant levels were assessed using historical sediment chemistry data, Effects Range Low and Median concentrations (ER-L and ER-M) as toxicological benchmarks, and a sum of toxicity units approach for multiple contaminants. Data on toxicity testing and biological monitoring was compared to sediment and water quality data. Fish tissue data were used to examine bioaccumulated chemicals. A computerized Geographical Information System (GIS) was used to manipulate and display complex geographical data. The final identification of areas and chemicals of potential concern relied on a syntheses of these results as well as information on present and past contaminant loadings

Study on improving rail energy efficiency (E2) : best practices and strategies

Science.gov (United States)

2015-03-23

A recent Volpe Center report [1] for the Federal Railroad Administrations (FRA) Rail Energy, Environment, and Engine (E3) Technology research and development program reviewed rail industry best practices (BPs) and strategies for improving energy e...

Characteristics of Black Men Who Have Sex With Men in Baltimore, Philadelphia, and Washington, D.C.: Geographic Diversity in Socio-Demographics and HIV Transmission Risk.

Science.gov (United States)

German, Danielle; Brady, Kathleen; Kuo, Irene; Opoku, Jenevieve; Flynn, Colin; Patrick, Rudy; Park, Ju Nyeong; Adams, Joella; Carroll, Makeda; Simmons, Ron; Smith, Carlton R; Davis, Wendy W

2017-07-01

Baltimore, Philadelphia, and Washington, DC are geographically proximate cities with high HIV prevalence, including among black men who have sex with men (BMSM). Using data collected among BMSM in CDC's National HIV Behavioral Surveillance project, we compared socio-demographic characteristics, HIV risk behaviors, and service utilization to explore similarities and differences that could inform local and regional HIV intervention approaches. BMSM were recruited through venue time location sampling, June-December, 2011. Participants completed identical socio-behavioral surveys and voluntary HIV testing. Analyses were conducted among the full sample and those aged 18-24. Participants included 159 (DC), 364 (Baltimore), and 331 (Philadelphia) eligible BMSM. HIV prevalence was 23.1% (DC), 48.0% (Baltimore), 14.6% (Philadelphia) with 30.6%, 69.0%, 33.3% unrecognized HIV infection, respectively. Among BMSM 18-24, HIV prevalence was 11.1% (DC), 38.9% (Baltimore), 9.6% (Philadelphia) with unrecognized HIV infection 0.0%, 73.8%, 60.0% respectively. Compared with the other 2 cities, Baltimore participants were less likely to identify as gay/homosexual; more likely to report unemployment, incarceration, homelessness, sex exchange; and least likely to use the internet for partners. DC participants were more likely to have a college degree and employment. Philadelphia participants were more likely to report gay/homosexual identity, receptive condomless anal sex, having only main partners, and bars/clubs as partner meeting places. Sexually transmitted disease testing was universally low. Analyses showed especially high HIV prevalence among BMSM in Baltimore including among young BMSM. Socio-demographic characteristics and HIV infection correlates differed across cities but unrecognized HIV infection and unknown partner status were universally high.

Neutron measurement of residual stresses in a used railway rail

International Nuclear Information System (INIS)

Webster, P.J.; Low, K.S.; Mills, G.; Webster, G.A.

1990-01-01

The high resolution neutron diffraction technique has been applied to determine, non-destructively, the residual stress distribution developed in the head of a railway rail after normal service. Measurements were made, using the neutron strain scanner at the Institute Laue Langevin, Grenoble, on a transverse slice of rail 12mm thick taken from a section of straight track. The rail head was scanned in the three principal orientations in a series of parallel traverses sufficiently close to enable a two-dimensional matrix of data to be accumulated and vertical, transverse and longitudinal residual stress contours to be drawn. The results demonstrate the effectiveness and unique characteristics of the neutron technique to determine nondestructively and continuously the residual stresses inside engineering components

Planning, Investment, Construction and Operation of Rail Transit in Beijing

Institute of Scientific and Technical Information of China (English)

2012-01-01

In Beijing, the rail transit firstly came into existence in the mid 1960s and was officially put into operation for civil use in the early 1980s. It has entered a period of rapid development since 2001, with thanks to the coming of the Olympic Games in 2008, and has been playing a more and more important role in the passenger transport of Beijing since then on, as a key part of the public transportation. Based on a resume on the evolution of rail transit development in Beijing, this paper analyzes the mechanism of policy-making, the mode of investment and financing, the procedure of construction, and the management of operation of rail transit, all of which ensure its rapid development and effective performance.

49 CFR 172.820 - Additional planning requirements for transportation by rail.

Science.gov (United States)

2010-10-01

... identify a point of contact (including the name, title, phone number and e-mail address) on routing issues... Additional planning requirements for transportation by rail. (a) General. Each rail carrier transporting in... materials transported (instead of only highway route controlled quantities of Class 7 materials) and for all...

Passenger Rail Car Egress -- TRB Workshop

Science.gov (United States)

2011-11-01

The Federal Railroad Administrations (FRA) Office of Railroad Policy and Development is exploring how to enhance regulations that address the safe, timely, and effective emergency evacuation of occupants from passenger rail vehicles in various eme...

Long Term Land Use Effects of New Rail Investment: Lessons from San Diego

Directory of Open Access Journals (Sweden)

David A. King

2018-01-01

Full Text Available In recent decades, U.S. cities have invested in rail transit for reasons beyond supplying alternatives to driving. Increasingly, rail investments are specifically promoted to reshape the built environment for property-led economic development. In these cases, new investment in rail transit is claimed to facilitate particular types of land use changes, mostly in the form of dense multi-family residential and mixed-use developments. Although rail’s effects on land use are widely claimed, scholarly evaluations offer mixed results. This paper examines two potential reasons for these mixed results. First, as most empirical examinations tend to be conducted shortly after new transit investment opens analysis is often criticized on the basis that short time frames may not allow land use changes to materialize. The second is that rail investment often includes changes to local zoning and land use regulations, creating opportunities for types of development that were previously outlawed. This paper evaluates these two critiques through an analysis of long-term land use effects associated with new rail transit service in San Diego, California. The results suggest that even after three decades of development cycles, rail transit has not led to consistent regulatory patterns of increased density or new mixed-use development.

Does mercury contamination reduce body condition of endangered California clapper rails?

International Nuclear Information System (INIS)

Ackerman, Joshua T.; Overton, Cory T.; Casazza, Michael L.; Takekawa, John Y.; Eagles-Smith, Collin A.; Keister, Robin A.; Herzog, Mark P.

2012-01-01

We examined mercury exposure in 133 endangered California clapper rails (Rallus longirostris obsoletus) within tidal marsh habitats of San Francisco Bay, California from 2006 to 2010. Mean total mercury concentrations were 0.56 μg/g ww in blood (range: 0.15–1.43), 9.87 μg/g fw in head feathers (3.37–22.0), 9.04 μg/g fw in breast feathers (3.68–20.2), and 0.57 μg/g fww in abandoned eggs (0.15–2.70). We recaptured 21 clapper rails and most had low within-individual variation in mercury. Differences in mercury concentrations were largely attributed to tidal marsh site, with some evidence for year and quadratic date effects. Mercury concentrations in feathers were correlated with blood, and slopes differed between sexes (R 2 = 0.58–0.76). Body condition was negatively related to mercury concentrations. Model averaged estimates indicated a potential decrease in body mass of 20–22 g (5–7%) over the observed range of mercury concentrations. Our results indicate the potential for detrimental effects of mercury contamination on endangered California clapper rails in tidal marsh habitats. - Highlights: ► We examined mercury in endangered California clapper rails within tidal marshes. ► Differences in mercury concentrations were largely attributed to tidal marsh site. ► Mercury concentrations in blood, feathers, and eggs were considered elevated. ► Body condition was negatively related to mercury concentrations. ► Results indicate detrimental effects of mercury on endangered clapper rails. - Mercury contamination in endangered California clapper rails was influenced by tidal marsh site and increased mercury resulted in reduced bird body condition.

75 FR 51333 - Madison Square Federal Savings Bank, Baltimore, MD; Approval of Conversion Application

Science.gov (United States)

2010-08-19

... DEPARTMENT OF THE TREASURY Office of Thrift Supervision [AC-49: OTS Nos. 08156 and H4736] Madison Square Federal Savings Bank, Baltimore, MD; Approval of Conversion Application Notice is hereby given that on August 12, 2010, the Office of Thrift Supervision approved the application of Madison Square...

75 FR 41927 - Ideal Federal Savings Bank, Baltimore, Maryland; Notice of Appointment of Receiver

Science.gov (United States)

2010-07-19

... DEPARTMENT OF THE TREASURY Office of Thrift Supervision Ideal Federal Savings Bank, Baltimore... contained in section 5(d)(2) of the Home Owners' Loan Act, the Office of Thrift Supervision has duly appointed the Federal Deposit Insurance Corporation as sole Receiver for Ideal Federal Savings Bank...

2006 Rare Neuroimmunological Disorders Symposium; Sheraton Inner Harbor, Baltimore, MD, July 20-23, 2006

DEFF Research Database (Denmark)

Kerr, DA; Antel, JP; Arnold, DL

2007-01-01

On July 20-22nd 2006, the second International Rare Neuroimmunologic Disorders Symposium was held in Baltimore, Maryland. The purpose of this symposium was to bring together diverse groups interested in immune-mediated disorders of the nervous system. The symposium was not disease-specific but at...

Inferring ecological relationships from occupancy patterns for California Black Rails in the Sierra Nevada foothills

Science.gov (United States)

Richmond, Orien Manu Wright

The secretive California Black Rail (Laterallus jamaicensis coturniculus ) has a disjunct and poorly understood distribution. After a new population was discovered in Yuba County in 1994, we conducted call playback surveys from 1994--2006 in the Sierra foothills and Sacramento Valley region to determine the distribution and residency of Black Rails, estimate densities, and obtain estimates of site occupancy and detection probability. We found Black Rails at 164 small, widely scattered marshes distributed along the lower western slopes of the Sierra Nevada foothills, from just northeast of Chico (Butte County) to Rocklin (Placer County). Marshes were surrounded by a matrix of unsuitable habitat, creating a patchy or metapopulation structure. We observed Black Rails nesting and present evidence that they are year-round residents. Assuming perfect detectability we estimated a lower-bound mean Black Rail density of 1.78 rails ha-1, and assuming a detection probability of 0.5 we estimated a mean density of 3.55 rails ha-1. We test if the presence of the larger Virginia Rail (Laterallus limicola) affects probabilities of detection or occupancy of the smaller California Black Rail in small freshwater marshes that range in size from 0.013-13.99 ha. We hypothesized that Black Rail occupancy should be lower in small marshes when Virginia Rails are present than when they are absent, because resources are presumably more limited and interference competition should increase. We found that Black Rail detection probability was unaffected by the detection of Virginia Rails, while, surprisingly, Black and Virginia Rail occupancy were positively associated even in small marshes. The average probability of Black Rail occupancy was higher when Virginia Rails were present (0.74 +/- 0.053) than when they were absent (0.36 +/- 0.069), and for both species occupancy increased with marsh size. We assessed the impact of winter (November-May) cattle grazing on occupancy of California Black

Demand forecast for rail shipment of radioactive material in the United States

International Nuclear Information System (INIS)

Allen, G.C.; Cashwell, J.W.

1981-01-01

A summary of the market potential for radioactive material (in millions of ton-miles) is presented in tabular form. These include the following: milled uranium ore; mill tailings; natural uranium hexafluoride; enriched uranium hexafluoride; fresh fuel, spent fuel; low-level waste; transuranic waste; and high-level waste. The maximum realistic market share for rail carriers is always less than these values because of the lack of rail access to some shipping and receiving facilities, small material quantities which could most easily move by other modes, short shipping distances for certain transport segments and greater operational convenience of other modes for some material categories. While market share and revenues for radioactive material are presently small, rail carriers appear to have a market advantage for milled uranium ore, transuranic waste and high-level waste. The potential for a significantly increased market share exists for spent fuel and uranium hexafluoride. While more fresh fuel and low-level waste can be transported by rail, it is unlikely that rail market share for radioactive materials (RAM) in general will rise to the potential maximum because many of these materials have historically been moved by truck and transported in frequent, small shipments

Simultaneous in-bore rail and insulator spectra from a railgun plasma armature

International Nuclear Information System (INIS)

Keefer, D.; Sedghinasah, A.; Crawford, R.

1991-01-01

This paper reports on absolute spectral radiance measurements obtained simultaneously at the rail and insulator surface of the UTSI 1 cm square-bore railgun. The emission spectra were obtained through the use of quartz optical fibers which penetrated both the rail and the insulator walls. The spectral characteristics of the rail and insulator emission are quite similar but differ significantly in magnitude. A detailed plasma radiation model was used to analyze these spectra. In order to obtain reasonable agreement between the model predictions and the experimental spectra, it was necessary to assume that these existed a broadband absorbing layer at the insulator surface. This result suggests a new physical model of the plasma armature in which insulator ablation leads to significant 3-dimensional flow and affects the shape of the current emission pattern on the rail surfaces

Radiological mapping of Mumbai-Chatrapur (Odisha) rail route

International Nuclear Information System (INIS)

Patra, R.P.; Patil, S.S.; Murali, S.; Singh, Rajvir; Pradeepkumar, K.S.

2014-01-01

The radiation mapping at various stations along Mumbai-Chatrapur rail route was carried out using GM, Plastic scintillator and NaI(Tl) based detectors. It has been observed that the average radiation level during the entire Mumbai-Chatrapur rail route was 63.8±6.l nSv h -1 and the maximum dose rate was 94.5±12.7 nSv h -1 and 103.2±10.2 nSv h -1 near Secunderabad and Chatrapur station respectively. The elevated radiation level at few locations was mainly due to the presence of terrestrial radiation i.e. naturally occurring radioactive material (NORM) viz., Thorium ( 232 Th) and Potassium ( 40 K) present in the environment. The spectral analysis led to confirming the presence of 232 Th and 40 K at the places. The main aim of the work was to generate the country wide baseline radiological data along selected important rail routes that could be used for radiological impact assessment. The results reported in this work would be helpful to provide valuable/useful reference data during the impact assessment at different locations

APPLICATION OF NFC TECHNOLOGY IN PASSENGER RAIL TRANSPORT

Directory of Open Access Journals (Sweden)

Henryk KOMSTA

2016-09-01

Full Text Available The article discusses the possibility of the application of the NFC technology as a system of selling tickets in passenger rail transport. The NFC (Near Field Communication technology is a wireless and contactless technology of transmission of radio data over short distances (max. 5 cm. This technology is very similar to the RFID (Radio Frequency Identification technology. It is assumed that this technology will spread rapidly and that already in 2015 around 85% of the payments in the EU will be made via mobile phones. This paper presents a research of passenger interest in this method of payment for tickets in the passenger rail transport in Slovakia. Further, an analysis of the applications of the NFC technology as a system of selling tickets in passenger rail transport, including the protection of data in mobile phones, the processes in case of losing a mobile phone and ensuring the communication between both parties was presented in the article. The last part of this analysis shows the possibility of purchasing tickets regardless of the carrier and the transport type.

78 FR 17996 - MCM Rail Services LLC-Petition for Retroactive Exemption-In Sparrows Point, Md.

Science.gov (United States)

2013-03-25

... DEPARTMENT OF TRANSPORTATION Surface Transportation Board [Docket No. FD 35707] MCM Rail Services... regarding a petition for an operation exemption submitted by MCM Rail Services LLC (MCM) regarding 12 miles of rail line in Sparrows Point, Md. (the Line). DATES: MCM's supplemental information is due by April...

A Historical Evaluation of the U16a Tunnel, Nevada National Security Site, Nye County, Nevada Volume 2

Energy Technology Data Exchange (ETDEWEB)

Jones, Roberrt C. [Desert Research Inst. (DRI), Reno, NV (United States); Drollinger, Harold [Desert Research Inst. (DRI), Reno, NV (United States)

2013-06-01

This report presents a historical evaluation of the U16a Tunnel on the Nevada National Security Site in southern Nevada. The work was conducted by the Desert Research Institute at the request of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office and the U.S. Department of Defense, Defense Threat Reduction Agency. The U16a Tunnel was used for underground nuclear weapons effects tests in Shoshone Mountain in Area 16 of the Nevada National Security Site. Six nuclear tests were conducted in the U16a Tunnel from 1962 to 1971. These tests are Marshmallow, Gum Drop, Double Play, Ming Vase, Diamond Dust, and Diamond Mine. The U.S. Department of Defense Threat Reduction Agency, with participation from Lawrence Livermore National Laboratory and Las Alamos National Laboratory, sponsored the tests. Fifteen high explosives tests were also conducted at the tunnel. Two were calibration tests during nuclear testing and the remaining were U.S. Department of Defense, Defense Threat Reduction Agency tunnel defeat tests. The U16a Tunnel complex is on the top and slopes of Shoshone Mountain, encompassing an area of approximately 16.7 hectares (41.1 acres). Major modifications to the landscape are a result of three principal activities, road construction and maintenance, mining activities related to development of the tunnel complex, and site preparation for activities related to testing. Forty-seven cultural features were recorded at the portal and on the slopes of Shoshone Mountain. At the portal area, features relate to the mining, construction, testing, and general every day operational support activities within the tunnel. These include concrete foundations for buildings, equipment pads, and rail lines. Features on the slopes above the tunnel relate to tunnel ventilation, borehole drilling, and data recording. Feature types include soil-covered bunkers, concrete foundations, instrument cable holes, drill holes, and ventilation shafts. The U16

A Historical Evaluation of the U16a Tunnel, Nevada National Security Site, Nye County, Nevada Volume 1

Energy Technology Data Exchange (ETDEWEB)

Jones, Robert C. [Desert Research Inst. (DRI), Reno, NV (United States); Drollinger, Harold [Desert Research Inst. (DRI), Reno, NV (United States); Bullard, Thomas F. [Desert Research Inst. (DRI), Reno, NV (United States); Ashbaugh, Laurence J. [Desert Research Inst. (DRI), Reno, NV (United States); Griffin, Wayne R. [Desert Research Inst. (DRI), Reno, NV (United States)

2013-01-01

This report presents a historical evaluation of the U16a Tunnel on the Nevada National Security Site in southern Nevada. The work was conducted by the Desert Research Institute at the request of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office and the U.S. Department of Defense, Defense Threat Reduction Agency. The U16a Tunnel was used for underground nuclear weapons effects tests in Shoshone Mountain in Area 16 of the Nevada National Security Site. Six nuclear tests were conducted in the U16a Tunnel from 1962 to 1971. These tests are Marshmallow, Gum Drop, Double Play, Ming Vase, Diamond Dust, and Diamond Mine. The U.S. Department of Defense Threat Reduction Agency, with participation from Lawrence Livermore National Laboratory and Las Alamos National Laboratory, sponsored the tests. Fifteen high explosives tests were also conducted at the tunnel. Two were calibration tests during nuclear testing and the remaining were U.S. Department of Defense, Defense Threat Reduction Agency tunnel defeat tests. The U16a Tunnel complex is on the top and slopes of Shoshone Mountain, encompassing an area of approximately 16.7 hectares (41.1 acres). Major modifications to the landscape are a result of three principal activities, road construction and maintenance, mining activities related to development of the tunnel complex, and site preparation for activities related to testing. Forty-seven cultural features were recorded at the portal and on the slopes of Shoshone Mountain. At the portal area, features relate to the mining, construction, testing, and general every day operational support activities within the tunnel. These include concrete foundations for buildings, equipment pads, and rail lines. Features on the slopes above the tunnel relate to tunnel ventilation, borehole drilling, and data recording. Feature types include soil-covered bunkers, concrete foundations, instrument cable holes, drill holes, and ventilation shafts. The U16

Evolving diesel common rail technology for future low emission standards

Energy Technology Data Exchange (ETDEWEB)

Schoeppe, D.; Bercher, P.; Guerrassi, N.; Spadafora, P. [Delphi Diesel Systems, Paris (France)

2005-07-01

The Diesel fuel injection equipment will remain a key element for Diesel engine technology evolution. Achieving emission targets at competitive prices has been and will continue to be a major technical challenge to the engine manufacturer. Delphi is continously developing its Common Rail System and its components for fulfill future stricter emission legislation while simultaneously improving performance on noise, fuel consumption and power output. The outstanding and unique injector concept combined with innovative control strategies has largely contributed to the improvement of exhaust emission and performance, consumption and NVH over the lifetime of Diesel vehicles. Recently, Euro 4 common rail applications have been introduced on several applications by adding further capability such as multiple injection, small-injected quantity control and improved atomization. This papers will describe the latest Common Rail System developments that Delphi will introduce into the market to comply with future legislative emission targets. Further, a novel common rail injector will be presented, that uses a revolutionary, direct acting operating principle, where the nozzle is directly operated by a piezo actuator, without the use of a servo-hydraulic flow circuit. The superior performance of this injector concept will be shown, especially with regard to it's near square rate injection shape, minimum quantity capability as well as multiple injection performance. The direct acting operating principle allows rapid opening and closing of the injector, without compromising pilot quantity capability. The emission benefit obtained by such opening and closing behavior will be shown. Finally, based on the findings discussed, the papers will conclude on key features of future common rail systems. (orig.)

Environmental risk analysis of hazardous material rail transportation

Energy Technology Data Exchange (ETDEWEB)

Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Werth, Charles J.; Schaeffer, David [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Yoon, Hongkyu [Sandia National Laboratories, Albuquerque, NM 87123 (United States); Barkan, Christopher P.L. [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States)

2014-01-15

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials.

Environmental risk analysis of hazardous material rail transportation

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Werth, Charles J.; Schaeffer, David; Yoon, Hongkyu; Barkan, Christopher P.L.

2014-01-01

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials

SQUEEZING EFFECT OF RAIL LOADED BY SEMI-SLEEPERS HAVING L-SHAPED CROSS-SECTION

Directory of Open Access Journals (Sweden)

V. N. Sukhodoev

2015-01-01

Full Text Available The paper considers a problem on introduction of a conception and regularities of “squeezing effect of a rail loaded non centrally by semi-sleepers having L-shaped cross-section” exemplified by belt-type tramway. Its advantages are ensured by doubled non centrally loaded foundations these are semi-sleepers. Semi-sleeper of L-shape cross-section is a lever of L-shape form, transforming a vertical load into horizontal ones and foundation squeezing. Properties of two semi-sleepers being doubled, orientated to each other and non centrally loaded have been used in order to create a positive effect. A horizontal force creates squeezing and it is revealed as a component of a vertical load during displacements which functionally depend on foundation squeezing. These dependences demonstrate that strength and deformation properties of earth foundation of vertical direction are used for creation of horizontal properties of sleeper vertical shoulder.The paper studies mechanics pertaining to a squeezing effect of a rail loaded by semi-sleepers having L-shaped cross-section. It has been established that the rail squeezing effect results from squeezing process executed in two mutually perpendicular directions (reduction of cross-sectional area by load of a rail wheel with spacers if they are set inside of a sleeper-mechanism on an elastic foundation.Methodology for calculation of parameters on the rail reduction effect is considered as a tool for handling of applied problems on belt-type tramways. Results of the proposed rail reduction effect in problem statement for elastic conditions, with unchanged cross-sectional dimension of a rail line and introduction of correction ratio coefficients due to new initial load data have recommended for practical application as reliable values.The paper has revealed a proportional dependence of the rail reduction effect according to strength on the resultant value of reaction pressure, eccentricity difference of the

Personal interests hinder Rail Baltica

Index Scriptorium Estoniae

2011-01-01

Läti seimi liige Janis Reirs leiab, et Rail Baltica ehitus on Moskva ja Riia vahelise raudtee ehitusest prioriteetsem, kuna esimest võib potentsiaalselt finantseerida Euroopa Liit. Transpordiminister Uldis Augulis kohtub oma Venemaa kolleegi Igor Levitiniga 7. aprillil. Peaminister Valdis Dombrovskise sõnul vajavad mõlemad projektid majandusanalüüsi

49 CFR 214.525 - Towing with on-track roadway maintenance machines or hi-rail vehicles.

Science.gov (United States)

2010-10-01

... or hi-rail vehicles. 214.525 Section 214.525 Transportation Other Regulations Relating to... SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.525 Towing with on-track roadway maintenance machines or hi-rail vehicles. (a) When used to tow pushcars or other maintenance-of-way equipment...

An Evaluation of the Low-Carbon Effects of Urban Rail Based on Mode Shifts

Directory of Open Access Journals (Sweden)

Feng Chen

2017-03-01

Full Text Available Urban rail is widely considered to be a form of low-carbon green transportation, but there is a lack of specific quantitative research to support this. By comparing the mode, distance, and corresponding energy consumption of residents before and after the opening of rail transit, this paper establishes a carbon reduction method for rail transit. A measurement model takes the passenger carbon emissions before the line is opened as the baseline and compares them with the standard after the opening, determining the carbon emissions reduction. The model requires a combination of a large amount of research data, transit smart card data, and GIS network measurement tools as measured data and parameters. The model is then applied to rail transit lines that have opened in Beijing in recent years. The emissions reductions of four different routes are estimated and the carbon emissions reduction effect of rail transit is evaluated.

System and prospects of China's intercity rail transit technology

Science.gov (United States)

Gong, Ming

2018-06-01

City clusters and metropolitan areas in China are flourishing in the midst of the deepening urbanization in the country, thereby resulting in the emergence of intercity rail transit. Intercity railways connect mainline and urban railways for an integrated regional transportation system that underpins and leads the development of city clusters and metropolitan areas. This study explores the development mode and service characteristics of intercity rail transit, as well as proposes overviews on this system and prospects of its future technology in China.

Passenger train emergency systems : development of prototype railEXODUS software for U.S. passenger rail car egress.

Science.gov (United States)

2014-11-01

The Federal Railroad Administration (FRA), U.S. Department of Transportation (U.S. DOT), is sponsoring a research program, which includes investigation of the applicability of time-based egress performance requirements to U.S. passenger rail cars. Th...

Experimental investigation into the fault response of superconducting hybrid electric propulsion electrical power system to a DC rail to rail fault

Science.gov (United States)

Nolan, S.; Jones, C. E.; Munro, R.; Norman, P.; Galloway, S.; Venturumilli, S.; Sheng, J.; Yuan, W.

2017-12-01

Hybrid electric propulsion aircraft are proposed to improve overall aircraft efficiency, enabling future rising demands for air travel to be met. The development of appropriate electrical power systems to provide thrust for the aircraft is a significant challenge due to the much higher required power generation capacity levels and complexity of the aero-electrical power systems (AEPS). The efficiency and weight of the AEPS is critical to ensure that the benefits of hybrid propulsion are not mitigated by the electrical power train. Hence it is proposed that for larger aircraft (~200 passengers) superconducting power systems are used to meet target power densities. Central to the design of the hybrid propulsion AEPS is a robust and reliable electrical protection and fault management system. It is known from previous studies that the choice of protection system may have a significant impact on the overall efficiency of the AEPS. Hence an informed design process which considers the key trades between choice of cable and protection requirements is needed. To date the fault response of a voltage source converter interfaced DC link rail to rail fault in a superconducting power system has only been investigated using simulation models validated by theoretical values from the literature. This paper will present the experimentally obtained fault response for a variety of different types of superconducting tape for a rail to rail DC fault. The paper will then use these as a platform to identify key trades between protection requirements and cable design, providing guidelines to enable future informed decisions to optimise hybrid propulsion electrical power system and protection design.

Cooled electronic system with thermal spreaders coupling electronics cards to cold rails

Science.gov (United States)

Chainer, Timothy J; Gaynes, Michael A; Graybill, David P; Iyengar, Madhusudan K; Kamath, Vinod; Kochuparambil, Bejoy J; Schmidt, Roger R; Schultz, Mark D; Simco, Daniel P; Steinke, Mark E

2013-07-23

Liquid-cooled electronic systems are provided which include an electronic assembly having an electronics card and a socket with a latch at one end. The latch facilitates securing of the card within the socket or removal of the card from the socket. A liquid-cooled cold rail is disposed at the one end of the socket, and a thermal spreader couples the electronics card to the cold rail. The thermal spreader includes first and second thermal transfer plates coupled to first and second surfaces on opposite sides of the card, and thermally conductive extensions extending from end edges of the plates, which couple the respective transfer plates to the liquid-cooled cold rail. The thermally conductive extensions are disposed to the sides of the latch, and the card is securable within or removable from the socket using the latch without removing the cold rail or the thermal spreader.

Passenger flow analysis of Beijing urban rail transit network using fractal approach

Science.gov (United States)

Li, Xiaohong; Chen, Peiwen; Chen, Feng; Wang, Zijia

2018-04-01

To quantify the spatiotemporal distribution of passenger flow and the characteristics of an urban rail transit network, we introduce four radius fractal dimensions and two branch fractal dimensions by combining a fractal approach with passenger flow assignment model. These fractal dimensions can numerically describe the complexity of passenger flow in the urban rail transit network and its change characteristics. Based on it, we establish a fractal quantification method to measure the fractal characteristics of passenger follow in the rail transit network. Finally, we validate the reasonability of our proposed method by using the actual data of Beijing subway network. It has been shown that our proposed method can effectively measure the scale-free range of the urban rail transit network, network development and the fractal characteristics of time-varying passenger flow, which further provides a reference for network planning and analysis of passenger flow.

Life-cycle assessment of high-speed rail: the case of California

International Nuclear Information System (INIS)

Chester, Mikhail; Horvath, Arpad

2010-01-01

The state of California is expected to have significant population growth in the next half-century resulting in additional passenger transportation demand. Planning for a high-speed rail system connecting San Diego, Los Angeles, San Francisco, and Sacramento as well as many population centers between is now underway. The considerable investment in California high-speed rail has been debated for some time and now includes the energy and environmental tradeoffs. The per-trip energy consumption, greenhouse gas emissions, and other emissions are often compared against the alternatives (automobiles, heavy rail, and aircraft), but typically only considering vehicle operation. An environmental life-cycle assessment of the four modes was created to compare both direct effects of vehicle operation and indirect effects from vehicle, infrastructure, and fuel components. Energy consumption, greenhouse gas emissions, and SO 2 , CO, NO X , VOC, and PM 10 emissions were evaluated. The energy and emission intensities of each mode were normalized per passenger kilometer traveled by using high and low occupancies to illustrate the range in modal environmental performance at potential ridership levels. While high-speed rail has the potential to be the lowest energy consumer and greenhouse gas emitter, appropriate planning and continued investment would be needed to ensure sustained high occupancy. The time to environmental payback is discussed highlighting the ridership conditions where high-speed rail will or will not produce fewer environmental burdens than existing modes. Furthermore, environmental tradeoffs may occur. High-speed rail may lower energy consumption and greenhouse gas emissions per trip but can create more SO 2 emissions (given the current electricity mix) leading to environmental acidification and human health issues. The significance of life-cycle inventorying is discussed as well as the potential of increasing occupancy on mass transit modes.

Measurement and calculation of magnetic fields associated with rail-gun currents

International Nuclear Information System (INIS)

Kerrisk, J.F.; Fowler, C.M.; Peterson, D.R.

1983-01-01

The magnetic field associated with current flow in the rails of a rail gun has been measured. The test used a magnetic flux-compression generator and a 1.2-m-long rail gun to accelerate a 4.2-g arc-driven projectile to 3.5 km/s; peak current was 900 kA. Magnetic field probes, consisting of two-turn coils 6.4 mm in diam, were located at two axial locations along the rails. Probe 3, at 0.60 m from the breech, was 28 mm from the center of the bore, and Probe 4, at 0.85 m from the breech, was 19 mm from the center of the bore. Two-dimensional calculations of the field at the probe locations were done assuming that when current starts to flow at an axial location, it is distributed on the rail surface as in the high-frequency limit. When the projectile and arc are two to three times the transverse probe separation beyond the probe, the measured field should be approximately two-dimensional. Probe signals indicate that the projectile was traveling at 3.2 km/s when it passed Probe 4. At this velocity, the projectile should be three transferse probe separations (about 60 mm) from the axial probe location in about 20 μS. Allowing for a 40-mm arc length adds about 15 μS. With these assumptions, the measured field should approach the two-dimensional limit in about 35 μS. However, about 100 μS were required. The results from Probe 3 are similar. The cause of this delay is uncertain at this time; two possibilities that are being investigated are that the arc is much longer than expected or that current flow in the rails at these axial locations is less than that measured at the breech because of spurious arcs

In-Service Performance and Costs of Methods for Control of Urban Rail System Noise : Experimental Design

Science.gov (United States)

1976-05-01

This report presents an experimental design for a project to evaluate four techniques for reducing wheel-rail noise on urban rail transit systems: (a) resilient wheels, (b) damped wheels, (c) wheel truing, and (d) rail griding. The design presents th...

Distribution and habitat use of king rails in the Illinois and Upper Mississippi River valleys

Science.gov (United States)

Darrah, Abigail J.; Krementz, David G.

2009-01-01

The migratory population of the king rail (Rallus elegans) has declined dramatically during the past 40 years, emphasizing the need to identify habitat requirements of this species to help guide conservation efforts. To assess distribution and habitat use of king rails along the Illinois and Upper Mississippi valleys, USA, we conducted repeated call-broadcast surveys at 83 locations in 2006 and 114 locations in 2007 distributed among 21 study sites. We detected king rails at 12 survey locations in 2006 and 14 locations in 2007, illustrating the limited distribution of king rails in this region. We found king rails concentrated at Clarence Cannon National Wildlife Refuge, an adjacent private Wetlands Reserve program site, and B. K. Leach Conservation Area, which were located in the Mississippi River floodplain in northeast Missouri. Using Program PRESENCE, we estimated detection probabilities and built models to identify habitat covariates that were important in king rail site occupancy. Habitat covariates included percentage of cover by tall (> 1 m) and short (wetlands that were characterized by high water-vegetation interspersion and little or no cover by woody vegetation. Our results suggest that biologists can improve king rail habitat by implementing management techniques that reduce woody cover and increase vegetation-water interspersion in wetlands.

An Investigation into the Non-bulk Rail Freight Transport in Australia

Directory of Open Access Journals (Sweden)

Hadi Ghaderi

2015-03-01

Full Text Available In the last decade freight transport has gained further momentum in Australia, partly through significant demand growth at both domestic and international levels and partly as the result of Australia's long term need for infrastructure decision making. Amongst the freight task, non-bulk freight is the fastest growing freight task in Australia and is forecast to grow much faster than the rate of population growth and the average national GDP growth. However, rail's share in the non-bulk market has declined significantly in the last four decades. This study therefore provides an insight into the efficiency and operational management issues facing by the Australian non-bulk rail sector by focusing on three areas; the level of track compatibility and the relevant operational issues, the demographics of non-bulk freight in Australia and the current status of intermodal terminals in relation to rail connectivity and location. As the result, a more detailed understanding of the current shortages in the Australian non-bulk rail freight sector is achieved and managerial implications are provided.

On-rail solution for autonomous inspections in electrical substations

Science.gov (United States)

Silva, Bruno P. A.; Ferreira, Rafael A. M.; Gomes, Selson C.; Calado, Flavio A. R.; Andrade, Roberto M.; Porto, Matheus P.

2018-05-01

This work presents an alternative solution for autonomous inspections in electrical substations. The autonomous system is a robot that moves on rails, collects infrared and visible images of selected targets, also processes the data and predicts the components lifetime. The robot moves on rails to overcome difficulties found in not paved substations commonly encountered in Brazil. We take advantage of using rails to convey the data by them, minimizing the electromagnetic interference, and at the same time transmitting electrical energy to feed the autonomous system. As part of the quality control process, we compared thermographic inspections made by the robot with inspections made by a trained thermographer using a scientific camera Flir® SC660. The results have shown that the robot achieved satisfactory results, identifying components and measuring temperature accurately. The embodied routine considers the weather changes along the day, providing a standard result of the components thermal response, also gives the uncertainty of temperature measurement, contributing to the quality in the decision making process.

Thermal stress measurement in continuous welded rails using the hole-drilling method

Science.gov (United States)

Zhu, Xuan; Lanza di Scalea, Francesco; Fateh, Mahmood

2016-04-01

The absence of expansion joints in Continuous Welded Rail (CWR) has created the need for the railroad industry to determine the in-situ level of thermal stresses so as to prevent train accidents caused by rail buckling in hot weather and by rail breakage in cold weather. The development of non-destructive or semi-destructive methods for determining the level of thermal stresses in rails is today a high research priority. This study explores the known hole-drilling method as a possible solution to this problem. A new set of calibration coefficients to compute the relieved stress field with the finer hole depth increments was determined by a 3D Finite Element Analysis that modeled the entire hole geometry, including the mechanics of the hole bottom and walls. To compensate the residual stress components, a linear relationship was experimentally established between the longitudinal and the vertical residual stresses of two common sizes of rails, the 136RE and the 141RE, with statistical significance. This result was then utilized to isolate the longitudinal thermal stress component in hole-drilling tests conducted on the 136RE and 141RE thermally-loaded rails at the Large-scale CWR Test-bed of UCSD's Powell Research Laboratories. The results from the Test-bed showed that the hole-drilling procedure, with the appropriate residual stress compensation, can indeed estimate the in-situ thermal stresses to achieve a +/-5°F accuracy of Neutral Temperature determination with a 90% statistical confidence, which is the desired industry gold standard.

A highly successful model? The rail franchising business in Britain

OpenAIRE

Jupe, Robert E.; Funnell, Warwick N.

2017-01-01

A crucial feature of rail privatisation in Britain was franchising. Passenger services were franchised in competitive bidding processes to train operators which were meant to function with declining subsidy. The paper adopts the framework of social cost-benefit analysis to examine rail privatisation's impact on three key groups; consumers, producers and the government. It establishes that privatisation did not achieve all the supposed benefits. Further, franchising only appears to be profitab...

Rail Engineering and Education Symposium Materials.

Science.gov (United States)

2016-05-26

The objective of this project is to develop curricular materials for the Rail Engineering and Education : Symposia held in the summers of 2012 and 2014. : Description of Activities : The main approach to accomplish the activity is to develop and deli...

Immersive visualization of rail simulation data.

Science.gov (United States)

2016-01-01

The prime objective of this project was to create scientific, immersive visualizations of a Rail-simulation. This project is a part of a larger initiative that consists of three distinct parts. The first step consists of performing a finite element a...

49 CFR 174.84 - Position in train of loaded placarded rail cars, transport vehicles, freight containers or bulk...

Science.gov (United States)

2010-10-01

... CARRIAGE BY RAIL Handling of Placarded Rail Cars, Transport Vehicles and Freight Containers § 174.84 Position in train of loaded placarded rail cars, transport vehicles, freight containers or bulk packagings... 49 Transportation 2 2010-10-01 2010-10-01 false Position in train of loaded placarded rail cars...

49 CFR 174.82 - General requirements for the handling of placarded rail cars, transport vehicles, freight...

Science.gov (United States)

2010-10-01

... rail cars, transport vehicles, freight containers, and bulk packages. 174.82 Section 174.82... Placarded Rail Cars, Transport Vehicles and Freight Containers § 174.82 General requirements for the handling of placarded rail cars, transport vehicles, freight containers, and bulk packages. (a) Unless...

Parameters Studies on Surface Initiated Rolling Contact Fatigue of Turnout Rails by Three-Level Unreplicated Saturated Factorial Design

Directory of Open Access Journals (Sweden)

Xiaochuan Ma

2018-03-01

Full Text Available Surface initiated rolling contact fatigue (RCF, mainly characterized by cracks and material stripping, is a common type of damage to turnout rails, which can not only shorten service life of turnout but also lead to poor running safety of vehicle. The rail surface initiated RCF of turnouts is caused by a long-term accumulation, the size and distribution of which are related to the dynamic parameters of the complicated vehicle-turnout system. In order to simulate the accumulation of rail damage, some random samples of dynamic parameters significantly influencing it should be input. Based on the three-level unreplicated saturated factorial design, according to the evaluation methods of H, P and B statistic values, six dynamic parameters that influence the rail surface initiated RCF in turnouts, namely running speed of vehicle, axle load, wheel-rail profiles, integral vertical track stiffness and wheel-rail friction coefficient, are obtained by selecting 13 dynamic parameters significantly influencing the dynamic vehicle-turnout interaction as the analysis factors, considering four dynamic response results, i.e., the normal wheel-rail contact force, longitudinal creep force, lateral creep force and wheel-rail contact patch area as the observed parameters. In addition, the rail surface initiated RCF behavior in turnouts under different wheel-rail creep conditions is analyzed, considering the relative motion of stock/switch rails. The results show that the rail surface initiated RCF is mainly caused by the tangential stress being high under small creep conditions, the normal and tangential stresses being high under large creep conditions, and the normal stress being high under pure spin creep conditions.

Stochastic Channel Modeling for Railway Tunnel Scenarios at 25 GHz

Directory of Open Access Journals (Sweden)

Danping He

2018-02-01

Full Text Available More people prefer using rail traffic for travel or for commuting owing to its convenience and flexibility. The railway scenario has become an important communication scenario in the fifth generation era. The communication system should be designed to support high‐data‐rate demands with seamless connectivity at a high mobility. In this paper, the channel characteristics are studied and modeled for the railway tunnel scenario with straight and curved route shapes. On the basis of measurements using the “Mobile Hotspot Network” system, a three‐dimensional ray tracer (RT is calibrated and validated for the target scenarios. More channel characteristics are explored via RT simulations at 25.25 GHz with a 500‐MHz bandwidth. The key channel parameters are extracted, provided, and incorporated into a 3rd‐Generation‐Partnership‐Project‐like stochastic channel generator. The necessary channel information can be practically realized, which can support the link‐level and system‐level design of the communication system in similar scenarios.

Recruitment of older women: lessons learned from the Baltimore Hip Studies.

Science.gov (United States)

Resnick, Barbara; Concha, Betty; Burgess, Judy Graham; Fine, Mary Louise; West, Linda; Baylor, Karen; Nahm, Eun Shim; Buie, Verita Custis; Werner, Michelle; Orwig, Denise; Magaziner, Jay

2003-01-01

This study used a qualitative approach in which participants were asked to write about their experiences in recruiting older women into either one of two exercise intervention studies that are part of the Baltimore Hip Studies. The sample included 8 researcher nurses all women, White, and 42-53 years of age. Older adults, particularly older women, are less likely to participate in research studies when compared to their younger counterparts. The purpose of this study was to explore the techniques successfully used by research nurses in the Baltimore Hip Studies to recruit older women after hip fracture into exercise intervention studies. Data analysis was performed using basic content analysis (Crabtree & Miller, 1992; Miles & Huberman, 1984) "in vivo" coding (Dowd, 1991), or "grounded" coding (Glaser & Strauss, 1967), which involves using the informants' own words to capture a particular idea. A total of 16 codes were identified and reduced to nine themes. Seven themes focused on techniques that facilitated recruitment: (a) caring for individuals; (b) emphasizing benefits; (c) eliciting support from others; (d) being an expert; (e) using role models; (f) using good timing; and (g) giving good first impressions. The remaining two themes identified barriers to recruitment: (a) time commitment and (b) lack of support. Based on these themes, specific recruitment techniques are recommended. Ongoing research, however, is needed to establish the most effective recruitment procedures with older women.

Tunnel magnetoresistance in asymmetric double-barrier magnetic tunnel junctions

International Nuclear Information System (INIS)

Useinov, N.Kh.; Petukhov, D.A.; Tagirov, L.R.

2015-01-01

The spin-polarized tunnel conductance and tunnel magnetoresistance (TMR) through a planar asymmetric double-barrier magnetic tunnel junction (DBMTJ) have been calculated using quasi-classical model. In DBMTJ nanostructure the magnetization of middle ferromagnetic metal layer can be aligned parallel or antiparallel with respect to the fixed magnetizations of the top and bottom ferromagnetic electrodes. The transmission coefficients of an electron to pass through the barriers have been calculated in terms of quantum mechanics. The dependencies of tunnel conductance and TMR on the applied voltage have been calculated in case of non-resonant transmission. Estimated in the framework of our model, the difference between the spin-channels conductances at low voltages was found relatively large. This gives rise to very high magnitude of TMR. - Highlights: • The spin-polarized conductance through the junction is calculated. • Dependencies of the tunnel conductance vs applied bias are shown. • Bias voltage dependence of tunnel magnetoresistance for the structure is shown

The clinical impact of the couch top and rails on IMRT and arc therapy

International Nuclear Information System (INIS)

Pulliam, Kiley B; Howell, Rebecca M; Followill, David; Luo, Dershan; Kry, Stephen F; White, R Allen

2011-01-01

The clinical impact of the Varian Exact Couch on dose, volume coverage to targets and critical structures, and tumor control probability (TCP) has not been described. Thus, we examined their effects on IMRT and arc therapy. Five clinical prostate patients were planned with both 6 MV eight-field IMRT and 6 MV two-arc RapidArc techniques using the Eclipse treatment planning system. These plans neglected treatment couch attenuation, as is a common clinical practice. Dose distributions were then recalculated in Eclipse with the inclusion of the Varian Exact Couch (imaging couch top) and the rails in varying configurations. The changes in dose and coverage were evaluated using the dose-volume histograms from each plan iteration. We used a TCP model to calculate losses in tumor control resulting from not accounting for the couch top and rails. We also verified dose measurements in a phantom. Failure to account for the treatment couch and rails resulted in clinically unacceptable dose and volume coverage losses to the targets for both IMRT and RapidArc. The couch caused average prescription dose losses (relative to plans that ignored the couch) to the prostate of 4.2% and 2.0% for IMRT with the rails out and in, respectively, and 3.2% and 2.9% for RapidArc with the rails out and in, respectively. On average, the percentage of the target covered by the prescribed dose dropped to 35% and 84% for IMRT (rails out and in, respectively) and to 18% and 17% for RapidArc (rails out and in, respectively). The TCP was also reduced by as much as 10.5% (6.3% on average). Dose and volume coverage losses for IMRT plans were primarily due to the rails, while the imaging couch top contributed most to losses for RapidArc. Both the couch top and rails contribute to dose and coverage losses that can render plans clinically unacceptable. A follow-up study we performed found that the less attenuating unipanel mesh couch top available with the Varian Exact couch does not cause a clinically

Analysis and modeling of rail maintenance costs

Directory of Open Access Journals (Sweden)

Amir Ali Bakhshi

2012-01-01

Full Text Available Railroad maintenance engineering plays an important role on availability of roads and reducing the cost of railroad incidents. Rail is of the most important parts of railroad industry, which needs regular maintenance since it covers a significant part of total maintenance cost. Any attempt on optimizing total cost of maintenance could substantially reduce the cost of railroad system and it can reduce total cost of the industry. The paper presents a new method to estimate the cost of rail failure using different cost components such as cost of inspection and cost of risk associated with possible accidents. The proposed model of this paper is used for a real-world case study of railroad transportation of Tehran region and the results have been analyzed.

The impact of texting on driver behaviour at rail level crossings.

Science.gov (United States)

Young, Kristie L; Lenné, Michael G; Salmon, Paul M; Stanton, Neville A

2018-05-21

A driver text messaging in the vicinity of a rail level crossing represents the merging of a high-risk, high-workload driving environment with a highly distracting secondary task. In this simulator study, we examined how texting impacts driver behaviour on approach to actively controlled urban rail level crossings. Twenty-eight participants drove a series of simulated urban routes containing rail level crossings, while sending text messages and while driving without performing a secondary task. At half of the crossings, drivers were required to respond to the crossing warnings as a train approached. Results revealed that texting on approach to rail level crossings had a detrimental impact on a range of driver behaviour measures. Specifically, texting more than doubled the amount of time spent with eyes off the forward roadway, resulting in drivers spending more than half of their approach time to rail level crossings looking away from the road. This lack of visual attention to the roadway was associated with a range of decrements in driving that may be indicative of a loss of situation awareness, including increased brake reaction time to the crossing warnings and a reduction in lateral position control. The findings have safety implications, not only for urban level crossings, but also for passive level crossings where no warnings are present to re-orient the distracted driver's attention toward an approaching train. Copyright © 2018 Elsevier Ltd. All rights reserved.

Free Rail Tickets

DEFF Research Database (Denmark)

Reinau, Kristian Hegner; Harder, Henrik; Nielsen, Thomas Thomas Alexander Sick

2017-01-01

This article explores the potential of Bluetooth and WiFi sensor network tracking to estimate the flow of passengers on rails. The article shows that this technology makes it possible to estimate the relative flow in the network, even when used in a setup with a minimum of sensors on selected...... railway stations, and also how free tickets influence the relative flow on routes in the network. This paper presents the first contribution where Bluetooth and WiFi tracking data has been used to estimate the impact of free tickets on railways in Denmark....

49 CFR 214.521 - Flagging equipment for on-track roadway maintenance machines and hi-rail vehicles.

Science.gov (United States)

2010-10-01

... maintenance machines and hi-rail vehicles. 214.521 Section 214.521 Transportation Other Regulations Relating... WORKPLACE SAFETY On-Track Roadway Maintenance Machines and Hi-Rail Vehicles § 214.521 Flagging equipment for on-track roadway maintenance machines and hi-rail vehicles. Each on-track roadway maintenance machine...

An ultrasonically levitated noncontact stage using traveling vibrations on precision ceramic guide rails.

Science.gov (United States)

Koyama, Daisuke; Ide, Takeshi; Friend, James R; Nakamura, Kentaro; Ueha, Sadayuki

2007-03-01

This paper presents a noncontact sliding table design and measurements of its performance via ultrasonic levitation. A slider placed atop two vibrating guide rails is levitated by an acoustic radiation force emitted from the rails. A flexural traveling wave propagating along the guide rails allows noncontact transportation of the slider. Permitting a transport mechanism that reduces abrasion and dust generation with an inexpensive and simple structure. The profile of the sliding table was designed using the finite-element analysis (FEA) for high levitation and transportation efficiency. The prototype sliding table was made of alumina ceramic (Al2O3) to increase machining accuracy and rigidity using a structure composed of a pair of guide rails with a triangular cross section and piezoelectric transducers. Two types of transducers were used: bolt-clamped Langevin transducers and bimorph transducers. A 40-mm long slider was designed to fit atop the two rail guides. Flexural standing waves and torsional standing waves were observed along the guide rails at resonance, and the levitation of the slider was obtained using the flexural mode even while the levitation distance was less than 10 microm. The levitation distance of the slider was measured while increasing the slider's weight. The levitation pressure, rigidity, and vertical displacement amplitude of the levitating slider thus were measured to be 6.7 kN/m2, 3.0 kN/microm/m2, and less than 1 microm, respectively. Noncontact transport of the slider was achieved using phased drive of the two transducers at either end of the vibrating guide rail. By controlling the phase difference, the slider transportation direction could be switched, and a maximum thrust of 13 mN was obtained.

Stationary Charging Station Design for Sustainable Urban Rail Systems: A Case Study at Zhuzhou Electric Locomotive Co., China

OpenAIRE

Heng Li; Jun Peng; Weirong Liu; Zhiwu Huang

2015-01-01

In 2014, more than 43 cities in China were racing to construct their urban rail systems (including metro and light rail systems), recognizing that an urban rail system will be a good solution to the tough problems that they are faced with, including traffic congestion and PM2.5 air pollution. On 22 August 2012, the first electric double-layer capacitor (EDLC) energy storage-type rail vehicle in the world was unveiled at Zhuzhou Electric Locomotive Co., China. The EDLC rail system has been con...

The Impact of Rail Fare Increases on Locational Behaviour.

OpenAIRE

Mackett, R.L.

1980-01-01

Many people who work in London live over 30 miles from their jobs and travel to work by rail. Their decisions about the choice of home and job have been influenced by the cost of travel at the time of the decision and the anticipated changes, with subsequent implications for the value of housing. Over the past ten years there has been a decline in employment in central London, with a concomitant growth in employment in the surrounding area, leading to a shift from rail to road for the journey...

50 CFR 20.104 - Seasons, limits, and shooting hours for rails, woodcock, and common (Wilson's) snipe.

Science.gov (United States)

2010-10-01

... rails, woodcock, and common (Wilson's) snipe. 20.104 Section 20.104 Wildlife and Fisheries UNITED STATES... for rails, woodcock, and common (Wilson's) snipe. This section provides for the annual hunting of certain rails, woodcock, and snipe in the 48 contiguous United States. [44 FR 7148, Feb. 6, 1979...

Stationary Charging Station Design for Sustainable Urban Rail Systems: A Case Study at Zhuzhou Electric Locomotive Co., China

Directory of Open Access Journals (Sweden)

Heng Li

2015-01-01

Full Text Available In 2014, more than 43 cities in China were racing to construct their urban rail systems (including metro and light rail systems, recognizing that an urban rail system will be a good solution to the tough problems that they are faced with, including traffic congestion and PM2.5 air pollution. On 22 August 2012, the first electric double-layer capacitor (EDLC energy storage-type rail vehicle in the world was unveiled at Zhuzhou Electric Locomotive Co., China. The EDLC rail system has been considered a promising sustainable urban rail system, which is expected to further improve the energy efficiency and to reduce environmental pollution. The first commercial EDLC tram produced by Zhuzhou Electric Locomotive Co. has been applied at Guangzhou Metro Corp. recently. From the view point of scientific research, the system design and energy management of EDLC rail systems have been extensively studied in the literature, while the stationary charging station design for the EDLC energy storage-type urban rail vehicles has been rarely reported. Thus, the aim of this paper is to report a stationary charging station that has been successfully applied in the EDLC rail system produced by Zhuzhou Electric Locomotive Co., China.

Nitrogen input from residential lawn care practices in suburban watersheds in Baltimore county, MD

Science.gov (United States)

Neely L. Law; Lawrence E. Band; J. Morgan. Grove

2004-01-01

A residential lawn care survey was conducted as part of the Baltimore Ecosystem Study, a Long-term Ecological Research project funded by the National Science Foundation and collaborating agencies, to estimate the nitrogen input to urban watersheds from lawn care practices. The variability in the fertilizer N application rates and the factors affecting the application...

ENVIRONMENTAL ASSESSMENT FOR THE PROPOSED WITHDRAWAL OF PUBLIC LANDS WITHIN AND SURROUNDING THE CALIENTE RAIL CORRIDOR, NEVADA

International Nuclear Information System (INIS)

DOE

2005-01-01

The purpose for agency action is to preclude surface entry and the location of new mining claims, subject to valid existing rights, within and surrounding the Caliente rail corridor as described in the Yucca Mountain FEIS (DOE 2002). This protective measure is needed to enhance the safe, efficient, and uninterrupted evaluation of land areas for potential rail alignments within the Caliente rail corridor. The evaluation will assist the DOE in determining, through the Rail Alignment environmental impact statement (EIS) process, whether to construct a branch rail line, and to provide support to the BLM in deciding whether or not to reserve a ROW for the rail line under the Federal Land Policy and Management Act (FLPMA). The BLM participated as a cooperating agency in preparing this EA because it is the responsible land manager and BLM staff could contribute resource specific expertise

ENVIRONMENTAL ASSESSMENT FOR THE PROPOSED WITHDRAWAL OF PUBLIC LANDS WITHIN AND SURROUNDING THE CALIENTE RAIL CORRIDOR, NEVADA

Energy Technology Data Exchange (ETDEWEB)

DOE

2005-12-01

The purpose for agency action is to preclude surface entry and the location of new mining claims, subject to valid existing rights, within and surrounding the Caliente rail corridor as described in the Yucca Mountain FEIS (DOE 2002). This protective measure is needed to enhance the safe, efficient, and uninterrupted evaluation of land areas for potential rail alignments within the Caliente rail corridor. The evaluation will assist the DOE in determining, through the Rail Alignment environmental impact statement (EIS) process, whether to construct a branch rail line, and to provide support to the BLM in deciding whether or not to reserve a ROW for the rail line under the Federal Land Policy and Management Act (FLPMA). The BLM participated as a cooperating agency in preparing this EA because it is the responsible land manager and BLM staff could contribute resource specific expertise.

Magnetic tunnel junctions with monolayer hexagonal boron nitride tunnel barriers

Energy Technology Data Exchange (ETDEWEB)

Piquemal-Banci, M.; Galceran, R.; Bouzehouane, K.; Anane, A.; Petroff, F.; Fert, A.; Dlubak, B.; Seneor, P. [Unité Mixte de Physique, CNRS, Thales, Univ. Paris-Sud, Université Paris-Saclay, Palaiseau 91767 (France); Caneva, S.; Martin, M.-B.; Weatherup, R. S.; Kidambi, P. R.; Robertson, J.; Hofmann, S. [Department of Engineering, University of Cambridge, Cambridge CB21PZ (United Kingdom); Xavier, S. [Thales Research and Technology, 1 avenue Augustin Fresnel, Palaiseau 91767 (France)

2016-03-07

We report on the integration of atomically thin 2D insulating hexagonal boron nitride (h-BN) tunnel barriers into Co/h-BN/Fe magnetic tunnel junctions (MTJs). The h-BN monolayer is directly grown by chemical vapor deposition on Fe. The Conductive Tip Atomic Force Microscopy (CT-AFM) measurements reveal the homogeneity of the tunnel behavior of our h-BN layers. As expected for tunneling, the resistance depends exponentially on the number of h-BN layers. The h-BN monolayer properties are also characterized through integration into complete MTJ devices. A Tunnel Magnetoresistance of up to 6% is observed for a MTJ based on a single atomically thin h-BN layer.

9 CFR 3.15 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.15 Section 3.15 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used to...

9 CFR 3.138 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.138 Section 3.138 Animals and Animal Products ANIMAL AND PLANT HEALTH... (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

9 CFR 3.88 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.88 Section 3.88 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used to...

9 CFR 3.114 - Primary conveyances (motor vehicle, rail, air and marine).

Science.gov (United States)

2010-01-01

..., rail, air and marine). 3.114 Section 3.114 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air and marine). (a) The animal cargo space of primary conveyances used in.... (e) The interiors of animal cargo spaces in primary conveyances must be kept clean. (f) Live marine...

9 CFR 3.62 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.62 Section 3.62 Animals and Animal Products ANIMAL AND PLANT HEALTH... (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

9 CFR 3.37 - Primary conveyances (motor vehicle, rail, air, and marine).

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Primary conveyances (motor vehicle, rail, air, and marine). 3.37 Section 3.37 Animals and Animal Products ANIMAL AND PLANT HEALTH... conveyances (motor vehicle, rail, air, and marine). (a) The animal cargo space of primary conveyances used in...

Variability in ACL tunnel placement: observational clinical study of surgeon ACL tunnel variability.

Science.gov (United States)

Wolf, Brian R; Ramme, Austin J; Wright, Rick W; Brophy, Robert H; McCarty, Eric C; Vidal, Armando R; Parker, Richard D; Andrish, Jack T; Amendola, Annunziato

2013-06-01

Multicenter and multisurgeon cohort studies on anterior cruciate ligament (ACL) reconstruction are becoming more common. Minimal information exists on intersurgeon and intrasurgeon variability in ACL tunnel placement. Purpose/ The purpose of this study was to analyze intersurgeon and intrasurgeon variability in ACL tunnel placement in a series of The Multicenter Orthopaedic Outcomes Network (MOON) ACL reconstruction patients and in a clinical cohort of ACL reconstruction patients. The hypothesis was that there would be minimal variability between surgeons in ACL tunnel placement. Cross-sectional study; Level of evidence, 3. Seventy-eight patients who underwent ACL reconstruction by 8 surgeons had postoperative imaging with computed tomography, and ACL tunnel location and angulation were analyzed using 3-dimensional surface processing and measurement. Intersurgeon and intrasurgeon variability in ACL tunnel placement was analyzed. For intersurgeon variability, the range in mean ACL femoral tunnel depth between surgeons was 22%. For femoral tunnel height, there was a 19% range. Tibial tunnel location from anterior to posterior on the plateau had a 16% range in mean results. There was only a small range of 4% for mean tibial tunnel location from the medial to lateral dimension. For intrasurgeon variability, femoral tunnel depth demonstrated the largest ranges, and tibial tunnel location from medial to lateral on the plateau demonstrated the least variability. Overall, surgeons were relatively consistent within their own cases. Using applied measurement criteria, 85% of femoral tunnels and 90% of tibial tunnels fell within applied literature-based guidelines. Ninety-one percent of the axes of the femoral tunnels fell within the boundaries of the femoral footprint. The data demonstrate that surgeons performing ACL reconstructions are relatively consistent between each other. There is, however, variability of average tunnel placement up to 22% of mean condylar depth

Interaction between groundwater and TBM (Tunnel Boring Machine) excavated tunnels

OpenAIRE

Font Capó, Jordi

2012-01-01

A number of problems, e.g. sudden inflows are encountered during tunneling under the piezometric level, especially when the excavation crosses high transmissivity areas. These inflows may drag materials when the tunnel crosses low competent layers, resulting in subsidence, chimney formation and collapses. Moreover, inflows can lead to a decrease in head level because of aquifer drainage. Tunnels can be drilled by a tunnel boring machine (TBM) to minimize inflows and groundwater impacts, restr...

77 FR 14058 - Santa Teresa Southern Railroad, LLC-Operation Exemption-Rail Line of Verde Logistics Railroad...

Science.gov (United States)

2012-03-08

... Southern Railroad, LLC--Operation Exemption--Rail Line of Verde Logistics Railroad, LLC at Santa Teresa... notice of exemption under 49 CFR 1150.31 to operate approximately 12,000 feet of rail line owned by Verde Logistics Railroad, LLC (Verde). The rail line extends between a point of connection with Union Pacific...

A dynamic wheel-rail impact analysis of railway track under wheel flat by finite element analysis

Science.gov (United States)

Bian, Jian; Gu, Yuantong; Murray, Martin Howard

2013-06-01

Wheel-rail interaction is one of the most important research topics in railway engineering. It involves track impact response, track vibration and track safety. Track structure failures caused by wheel-rail impact forces can lead to significant economic loss for track owners through damage to rails and to the sleepers beneath. Wheel-rail impact forces occur because of imperfections in the wheels or rails such as wheel flats, irregular wheel profiles, rail corrugations and differences in the heights of rails connected at a welded joint. A wheel flat can cause a large dynamic impact force as well as a forced vibration with a high frequency, which can cause damage to the track structure. In the present work, a three-dimensional finite element (FE) model for the impact analysis induced by the wheel flat is developed by the use of the FE analysis (FEA) software package ANSYS and validated by another validated simulation. The effect of wheel flats on impact forces is thoroughly investigated. It is found that the presence of a wheel flat will significantly increase the dynamic impact force on both rail and sleeper. The impact force will monotonically increase with the size of wheel flats. The relationships between the impact force and the wheel flat size are explored from this FEA and they are important for track engineers to improve their understanding of the design and maintenance of the track system.

RESIDUAL RESOURCE STUDY OF DEFECTIVE RAILS FOR TYPE P 50 CYCLE TEST OF ENDURANCE

Directory of Open Access Journals (Sweden)

R. M. Yosyfovych

2015-11-01

Full Text Available Purpose. The paper is devoted to the study and evaluation of residual life for defective rails P50 operated on the roads of the Kyiv subway, which are taken out of service because of defects 11.1-2 on the side of the rolling surface of the rail head. Methodology. The studies were performed with the use of experimental methods: testing of samples of defective rails in the cyclical strength of the pulse machine and testing of defective rails in the static load limit on the hydraulic vertical press. Findings. The performed experiments indicate that on the tests basis in 2 million cycles is only a small development (increase in size 0.5-0.7 mm of existing code defects 11.2 as a result of shedding the particles of crumble out metal on the side of the rails head of working prototypes. The intensity and the catastrophic development of defects, such as 11.2, or transformation of these defects in defects such as 21.2 or 30G.2 did not happen in any case. Originality. For the first time in Ukraine with the theoretical calculations substantiated the greater possibility of defects formation of contact fatigue origin in the form of spall and jag of metal on the surface of the rail, at the edge of the head. It is the result of the creation of a high degree of stress nonequilibrium compression in this area, due to the high values of principal normal stresses and appearance of large shear stresses in the body of the head at a depth of 2.5-3.5 mm, exceeding the yield strength and metal endurance. The tests of experimental prototypes of defective rails on high cycle endurance (based № = 2,1h10 cycles with periodic defectoscopic control were conducted. Practical value. In experiments, the new data of the resistance ability to spall rail defects on the surface of the head of rolling on the code 11.1-2 long-term cyclic loading equal to operational magnitude at the wheel load test of 2 million cycles was obtained. That is, the defective rails can have residual life

Partial digitization method of wave processes in rail lines on the discrete basis

International Nuclear Information System (INIS)

Tyurekhodzhaev, A.N.; Ibraev, A.G.

2006-01-01

Analytical solution of the problem about longitudinal vibration of the rail which lies on the ties taking into account contact dry friction between wheel and rail is provided by the method of partial digitization and Laplace dual integral transformation. (author)

Sustainability and Displacement: Assessing the Spatial Pattern of Residential Moves Near Rail Transit

Science.gov (United States)

2017-11-01

Rail transits association with gentrification has been a presence in the public discourse for some time and Los Angeles is no different. There is a prevailing public perception that Los Angeles' recent boom in rail transit development causes an in...

Deformation and lifetime behaviour of cyclic loaded rail and wheel steels

Energy Technology Data Exchange (ETDEWEB)

Denne, B.; Lang, K.-H.; Loehe, D. [Karlsruhe Univ. (T.H.) (Germany). Inst. fuer Werkstoffkunde 1

2000-07-01

Corrugation, shelling and squats are some unexpected technical problems caused by increasing service tonnage, increasing load of the rails and increasing train speed at Deutsche Bahn AG lines since the last decades. As the complex phenomena of rolling contact fatigue in the rail / wheel system is difficult to understand extensive investigations have to be done to describe the multiaxial rolling contact fatigue processes and to develop and verify multiaxial fatigue criteria and lifetime predictions. To reach this aim a reliable fatigue data base of the utilised steels is required. To obtain such data, specimens were worked out of rails and wheels used in high speed traffic. With these specimens the lifetime behaviour and the endurance limit were estimated from push-pull tests. For the rail steel stress and total strain controlled fatigue tests were performed. The resulting lifetime behaviour is compared. In the wheel there are several regions with different microstructures due to the heat treatment at the end of the manufacturing process. Specimens were taken from the wheel rim representing these different microstructures. With these specimens stress controlled fatigue tests were performed. The influence of the different microstructures on the deformation and lifetime behaviour is showed. (orig.)

Continuous Distributed Top-k Monitoring over High-Speed Rail Data Stream in Cloud Computing Environment

Directory of Open Access Journals (Sweden)

Hanning Wang

2013-01-01

Full Text Available In the environment of cloud computing, real-time mass data about high-speed rail which is based on the intense monitoring of large scale perceived equipment provides strong support for the safety and maintenance of high-speed rail. In this paper, we focus on the Top-k algorithm of continuous distribution based on Multisource distributed data stream for high-speed rail monitoring. Specifically, we formalized Top-k monitoring model of high-speed rail and proposed DTMR that is the Top-k monitoring algorithm with random, continuous, or strictly monotone aggregation functions. The DTMR was proved to be valid by lots of experiments.

HARDENING OF CRANE RAILS BY PLASMA DISCRETE-TIME SURFACE TREATMENT

Directory of Open Access Journals (Sweden)

S. S. Samotugin

2017-01-01

Full Text Available Crane wheels and rails are subjected to intensive wear in the process of operation. Therefore, improvement of these components’ performance can be considered a task of high importance. A promising direction in this regard is surface treatment by highly concentrated energy flows such as laser beams or plasma jets. This thesis suggests that the use of gradient plasma surface treatment can improve the performance of crane rails. A research was conducted, according to which hardened zones were deposited on crane rails under different treatment modes. Microhardness was measured both at the surface and in depth using custom-made microsections. The article includes the results of study of plasma surface hardening effects on wear resistance of crane rails. Change of plasma surface treatment parameters (current, plasma torch movement speed, argon gas flow rate allows for desired steel hardness and structure, while the choice of optimal location for hardened zones makes it possible to significantly improve wear resistance and crack resistance. As a result of plasma surface hardening, the fine-grained martensite structure is obtained with mainly lamellar morphology and higher hardness rate compared toinduction hardening or overlaying. Wear test of carbon steels revealed that plasma surfacing reduces abrasive wear rate compared to the irinitial state by 2 to 3 times. Enough sharp boundary between hardened and non-hardened portions has a positive effect on the performance of parts under dynamic loads, contributing to the inhibition of cracks during the transition from solid to a soft metal. For carbon and low alloy rail steels, the properties achieved by plasma surface hardening can effectively replace induction hardening or overlaying.The mode range for plasma surface treatment that allow sobtaining a surface layer with certain operating properties has been determined.

Gas density and rail pressure effects on diesel spray growth from a heavy-duty common rail injector

NARCIS (Netherlands)

Klein-Douwel, R.J.H.; Frijters, P.J.M.; Seykens, X.L.J.; Somers, L.M.T.; Baert, R.S.G.

2009-01-01

Formation of nonevaporating sprays from diesel fuel injection through a realistic heavy duty multihole common rail injector is studied in a newly developed high-pressure, high-temperature cell, using digital highspeed shadowgraphy at 4500 frames/s. Gas pressure was varied from 13 to 37 bar

Effects of profile wear on wheel–rail contact conditions and dynamic interaction of vehicle and turnout

Directory of Open Access Journals (Sweden)

Jingmang Xu

2016-01-01

Full Text Available Severe wear is a common damage mechanism in railway turnouts, which strongly affects the dynamic performance of railway vehicles and maintenance costs of tracks. This article explores the effects of profile wear on contact behaviors in the wheel–rail/switch contact and dynamic interaction, and nominal and measured worn turnout rail profiles are used as boundary conditions of wheel–rail contact. The calculation of the dynamic loads and the resultant contact stresses and internal stresses makes it possible to rationally design railway turnouts and correctly select the material to be applied for their components. For these reasons, the multi-body system SIMPACK and finite element software ANSYS are used to calculate the features of load and subsequently distributions of contact stresses and internal stresses in the regions of wheel–turnout components. The results show that profile wear disturbs the distribution of wheel–rail contact point pairs, changes the positions of wheel–rail contact points along the longitudinal direction, and affects the dynamic interaction of vehicle and turnout. For the measured profile in this article, profile wear aggravates vertical dynamic responses significantly but improves lateral dynamic responses. Profile wear disturbs the normal contact situations between the wheel and switch rail and worsens the stress state of the switch rail.

5 steps to delivering safe, secure and reliable rail solutions for the nuclear industry

Energy Technology Data Exchange (ETDEWEB)

Connelly, C. [Direct Rail Services, Warrington (United Kingdom)

2004-07-01

Direct Rail Services (DRS) has been operating since October 1995, following the decision by parent company, British Nuclear Fuels (BNFL), to create a strategic rail transport service. The decision came after the privatisation of the rail network in the UK, when the former British Rail was superseded by a range of private organisations responsible for separate areas of the industry. Individual companies became responsible for aspects such as the operation and maintenance of the network infrastructure and for passenger and freight train services. Rather than enter into contractual arrangements with third party contractors, DRS was formed - securing both the access and reliability of transport routes and availability of the rail network, providing greater guarantees about the levels of service delivery. The strategy of bringing this area of transport in house was concurrent with that of international transport, utilising its own fleet of ships for overseas fuel movements. Freight operations began in October 1995, with the first services operating between Sellafield and the low level radioactive waste facility at Drigg.

5 steps to delivering safe, secure and reliable rail solutions for the nuclear industry

International Nuclear Information System (INIS)

Connelly, C.

2004-01-01

Direct Rail Services (DRS) has been operating since October 1995, following the decision by parent company, British Nuclear Fuels (BNFL), to create a strategic rail transport service. The decision came after the privatisation of the rail network in the UK, when the former British Rail was superseded by a range of private organisations responsible for separate areas of the industry. Individual companies became responsible for aspects such as the operation and maintenance of the network infrastructure and for passenger and freight train services. Rather than enter into contractual arrangements with third party contractors, DRS was formed - securing both the access and reliability of transport routes and availability of the rail network, providing greater guarantees about the levels of service delivery. The strategy of bringing this area of transport in house was concurrent with that of international transport, utilising its own fleet of ships for overseas fuel movements. Freight operations began in October 1995, with the first services operating between Sellafield and the low level radioactive waste facility at Drigg

Improving Resource Allocation Decisions to Reduce the Risk of Terrorist Attacks on Passenger Rail Systems

Science.gov (United States)

2016-12-01

Rails: Analyzing Current Challenges, and Future Solutions (Syracuse: Maxwell School of Citizenship and Public Affairs, 2008), 18. 3 U.S. Department...Nicholas Armstrong et al., Securing America’s Passenger Rails: Analyzing Current Challenges, and Future Solutions (Syracuse: Maxwell School of Citizenship ...as a broken rail, a faulty wire connection, or an act of terrorism, could result in a shutdown. Communication systems use centralized digital

75 FR 66057 - Waybill Data Released in Three-Benchmark Rail Rate Proceedings

Science.gov (United States)

2010-10-27

... (CSX Transp. II), 584 F.3d 1076 (DC Cir. 2009), the Board modified its simplified rail rate guidelines...- Benchmark approach for smaller rail rate disputes. The Three-Benchmark method compares a challenged rate of...: The RSAM and R/VC >180 benchmarks. See Rate Guidelines--Non-Coal Proceedings, (Rate Guidelines) 1 S.T...

Application Analysis of BIM Technology in Metro Rail Transit

Science.gov (United States)

Liu, Bei; Sun, Xianbin

2018-03-01

With the rapid development of urban roads, especially the construction of subway rail transit, it is an effective way to alleviate urban traffic congestion. There are limited site space, complex resource allocation, tight schedule, underground pipeline complex engineering problems. BIM technology, three-dimensional visualization, parameterization, virtual simulation and many other advantages can effectively solve these technical problems. Based on the project of Shenzhen Metro Line 9, BIM technology is innovatively researched throughout the lifecycle of BIM technology in the context of the metro rail transit project rarely used at this stage. The model information file is imported into Navisworks for four-dimensional animation simulation to determine the optimum construction scheme of the shield machine. Subway construction management application platform based on BIM and private cloud technology, the use of cameras and sensors to achieve electronic integration, dynamic monitoring of the operation and maintenance of underground facilities. Make full use of the many advantages of BIM technology to improve the engineering quality and construction efficiency of the subway rail transit project and to complete the operation and maintenance.

Calibration of robotic drilling systems with a moving rail

Directory of Open Access Journals (Sweden)

Tian Wei

2014-12-01

Full Text Available Industrial robots are widely used in aircraft assembly systems such as robotic drilling systems. It is necessary to expand a robot’s working range with a moving rail. A method for improving the position accuracy of an automated assembly system with an industrial robot mounted on a moving rail is proposed. A multi-station method is used to control the robot in this study. The robot only works at stations which are certain positions defined on the moving rail. The calibration of the robot system is composed by the calibration of the robot and the calibration of the stations. The calibration of the robot is based on error similarity and inverse distance weighted interpolation. The calibration of the stations is based on a magnetic strip and a magnetic sensor. Validation tests were performed in this study, which showed that the accuracy of the robot system gained significant improvement using the proposed method. The absolute position errors were reduced by about 85% to less than 0.3 mm compared with the maximum nearly 2 mm before calibration.

The Legacy Effect: Understanding How Segregation and Environmental Injustice Unfold over Time in Baltimore

Science.gov (United States)

Morgan Grove; Laura Ogden; Steward Pickett; Chris Boone; Geoff Buckley; Dexter H. Locke; Charlie Lord; Billy Hall

2018-01-01

Legacies of social and environmental injustices can leave an imprint on the present and constrain transitions for more sustainable futures. In this article, we ask this question: What is the relationship of environmental inequality and histories of segregation? The answer for Baltimore is complex, where past practices of de jure and de facto segregation have created...

Erastaja varjas osalusi Rail Estonias / Anneli Ammas

Index Scriptorium Estoniae

Ammas, Anneli, 1962-

2001-01-01

Eesti Päevalehe andmeil on Eesti Raudtee erastamiskonkursi võitnud Rail Estonia suurim aktsionär John Orrison. Vt. samas "Töötasid koos Bushi kabinetis". Väidetavalt salgab J. Orrison Tony Massei tundmise maha

Leadership Talent: A Study of the Potential of People in the Australian Rail Industry

Directory of Open Access Journals (Sweden)

Janene Piip

2015-09-01

Full Text Available This paper discusses the importance of leadership talent in the rail industry in Australia. Like many other countries around the world, rail is troubled by its ability to attract new talent as older leaders with specialized knowledge retire. This study sought to identify whether the sector is making the most of the talent already existing within, knowing the barriers faced in attracting new industry entrants, and questions what can be done to strengthen current approaches to developing leaders. In exploring the meaning of leadership talent, from a skills based perspective with three levels of leaders, blended methods using semi-structured interviews and a survey were utilized. The study is important because it focuses on the people aspects of the industry, a little researched area of rail that has major implications for how employees are engaged and retained. The findings identified a certain mindset, culture and approach about leadership talent in organizations that overlooked the heterogeneity of rail organization populations, precluding certain groups of people from becoming leaders. The project identified that leadership and other soft skills required in the rail industry are both under researched, and often undervalued, for the impact that they can have on performance and productivity of companies. There are key messages from this study for both organizations as well as inspiring rail industry leaders.

INFRASTRUCTURE IN RAIL TRANSPORT IN BRAZIL

Directory of Open Access Journals (Sweden)

Debora Brito dos Santos

2018-03-01

Full Text Available Rail transport is the second mode most used in the country, due to the low cost of transporting large volumes over long distances. Although there was no investment in the expansion for a long time, after privatization there was a resumption of maintenance and expansion of the railways, but it is far from achieving international quality and performance indices. The objective of this work was a study on the rail transport in the country, to raise the structure of the Brazilian railway network. For the development of this article, the method used was bibliographic research in books, articles and websites. Although the Brazilian railway network is just over 12% of the railroad network in the United States, after the privatization of the sector, growth has resumed. The Bioceanic, a railroad that will connect the Atlantic Ocean to the Pacific Ocean, will improve the flow of agricultural production to overseas

Frequency driven inversion of tunnel magnetoimpedance and observation of positive tunnel magnetocapacitance in magnetic tunnel junctions

International Nuclear Information System (INIS)

Parui, Subir; Ribeiro, Mário; Atxabal, Ainhoa; Llopis, Roger; Bedoya-Pinto, Amilcar; Sun, Xiangnan; Casanova, Fèlix; Hueso, Luis E.

2016-01-01

The relevance for modern computation of non-volatile high-frequency memories makes ac-transport measurements of magnetic tunnel junctions (MTJs) crucial for exploring this regime. Here, we demonstrate a frequency-mediated effect in which the tunnel magnetoimpedance reverses its sign in a classical Co/Al 2 O 3 /NiFe MTJ, whereas we only observe a gradual decrease in the tunnel magnetophase. Such effects are explained by the capacitive coupling of a parallel resistor and capacitor in the equivalent circuit model of the MTJ. Furthermore, we report a positive tunnel magnetocapacitance effect, suggesting the presence of a spin-capacitance at the two ferromagnet/tunnel-barrier interfaces. Our results are important for understanding spin transport phenomena at the high frequency regime in which the spin-polarized charge accumulation due to spin-dependent penetration depth at the two interfaces plays a crucial role.

Frequency driven inversion of tunnel magnetoimpedance and observation of positive tunnel magnetocapacitance in magnetic tunnel junctions

Energy Technology Data Exchange (ETDEWEB)

Parui, Subir, E-mail: s.parui@nanogune.eu, E-mail: l.hueso@nanogune.eu; Ribeiro, Mário; Atxabal, Ainhoa; Llopis, Roger [CIC nanoGUNE, 20018 Donostia-San Sebastian (Spain); Bedoya-Pinto, Amilcar [CIC nanoGUNE, 20018 Donostia-San Sebastian (Spain); Max Planck Institute of Microstructure Physics, D-06120 Halle (Germany); Sun, Xiangnan [CIC nanoGUNE, 20018 Donostia-San Sebastian (Spain); National Center for Nanoscience and Technology, 100190 Beijing (China); Casanova, Fèlix; Hueso, Luis E., E-mail: s.parui@nanogune.eu, E-mail: l.hueso@nanogune.eu [CIC nanoGUNE, 20018 Donostia-San Sebastian (Spain); IKERBASQUE, Basque Foundation for Science, 48011 Bilbao (Spain)

2016-08-01

The relevance for modern computation of non-volatile high-frequency memories makes ac-transport measurements of magnetic tunnel junctions (MTJs) crucial for exploring this regime. Here, we demonstrate a frequency-mediated effect in which the tunnel magnetoimpedance reverses its sign in a classical Co/Al{sub 2}O{sub 3}/NiFe MTJ, whereas we only observe a gradual decrease in the tunnel magnetophase. Such effects are explained by the capacitive coupling of a parallel resistor and capacitor in the equivalent circuit model of the MTJ. Furthermore, we report a positive tunnel magnetocapacitance effect, suggesting the presence of a spin-capacitance at the two ferromagnet/tunnel-barrier interfaces. Our results are important for understanding spin transport phenomena at the high frequency regime in which the spin-polarized charge accumulation due to spin-dependent penetration depth at the two interfaces plays a crucial role.

Monitoring the reflection from an artificial defect in rail track using guided wave ultrasound

Science.gov (United States)

Loveday, Philip W.; Taylor, Rebecca M. C.; Long, Craig S.; Ramatlo, Dineo A.

2018-04-01

Guided wave ultrasound has the potential to detect relatively large defects in continuously welded rail track at long range. As monitoring can be performed in near real time it would be acceptable to only detect fairly large cracks provided this is achieved prior to complete rail breakage. Heavy haul rail lines are inspected periodically by conventional ultrasound and sections with even relatively small cracks are removed; therefore, no sizable defects are available to demonstrate monitoring in the presence of realistic environmental operating conditions. Instead, we glued a small mass to the rail to simulate reflection from a crack and monitored the guided wave signals as the glue joint deteriorated over time. Data was collected over a two week period on an operational heavy haul line. A piezoelectric transducer mounted under the head of the rail was used in pulse-echo mode to transmit and receive a mode of propagation with energy confined mainly in the head of the rail. The small mass was attached under the head of the rail, at a distance of 375m from the transducer, using a cyanoacrylate glue, which was not expected to remain intact for long. Pre-processing of the collected signals involved rejection of signals containing train noise, averaging, filtering and dispersion compensation. Reflections from aluminothermic welds were used to stretch and scale the signals to reduce the influence of temperature variations. Singular value decomposition and independent component analysis were then applied to the signals with the aim of separating the reflection caused by the artificial defect from the background signal. The performance of these techniques was compared for different time spans. The reflection from the artificial defect showed unanticipated fluctuations.

Carpal Tunnel Syndrome

Science.gov (United States)

... a passing cramp? It could be carpal tunnel syndrome. The carpal tunnel is a narrow passageway of ... three times more likely to have carpal tunnel syndrome than men. Early diagnosis and treatment are important ...

Optimization Design of Multi-Parameters in Rail Launcher System

Directory of Open Access Journals (Sweden)

Yujiao Zhang

2014-05-01

Full Text Available Today the energy storage systems are still encumbering, therefore it is useful to think about the optimization of a railgun system in order to achieve the best performance with the lowest energy input. In this paper, an optimal design method considering 5 parameters is proposed to improve the energy conversion efficiency of a simple railgun. In order to avoid costly trials, the field- circuit method is employed to analyze the operations of different structural railguns with different parameters respectively. And the orthogonal test approach is used to guide the simulation for choosing the better parameter combinations, as well reduce the calculation cost. The research shows that the proposed method gives a better result in the energy efficiency of the system. To improve the energy conversion efficiency of electromagnetic rail launchers, the selection of more parameters must be considered in the design stage, such as the width, height and length of rail, the distance between rail pair, and pulse forming inductance. However, the relationship between these parameters and energy conversion efficiency cannot be directly described by one mathematical expression. So optimization methods must be applied to conduct design. In this paper, a rail launcher with five parameters was optimized by using orthogonal test method. According to the arrangement of orthogonal table, the better parameters’ combination can be obtained through less calculation. Under the condition of different parameters’ value, field and circuit simulation analysis were made. The results show that the energy conversion efficiency of the system is increased by 71.9 % after parameters optimization.

Research on the Common Rail Pressure Overshoot of Opposed-Piston Two-Stroke Diesel Engines

OpenAIRE

Yi Lu; Changlu Zhao; Zhe Zuo; Fujun Zhang; Shuanlu Zhang

2017-01-01

The common rail pressure has a direct influence on the working stability of Opposed-Piston Two-Stroke (OP2S) diesel engines, especially on performance indexes such as power, economy and emissions. Meanwhile, the rail pressure overshoot phenomenon occurs frequently due to the operating characteristics of OP2S diesel engines, which could lead to serious consequences. In order to solve the rail pressure overshoot problem of OP2S diesel engines, a nonlinear concerted algorithm adding a speed stat...

Theory of superconducting tunneling without the tunneling Hamiltonian

International Nuclear Information System (INIS)

Arnold, G.B.

1987-01-01

When a tunneling barrier is nearly transparent, the standard tunneling (or transfer) Hamiltonian approximation fails. The author describes the theory which is necessary for calculating the tunneling current in these cases, and illustrate it by comparing theory and experiment on superconductor/insulator/superconductor (SIS) junctions have ultra-thin tunnel barriers. This theory accurately explains the subgap structure which appears in the dynamical resistance of such SIS junctions, including many observed details which no previous theory has reproduced. The expression for the current through an SIS junction with an ultrathin barrier is given by I(t) = Re{Sigma/sub n/ J/sub n/ (omega/sub o/)e/sup in omega/o/sup t/} where omega/sub o/ = 2eV/h is the Josephson frequency, V is the bias voltage, and the J/sub n/ are voltage dependent coefficients, one for each positive or negative integer, n, and n=0. The relative sign of the terms involving cos(n omega/sub o/t) and sin(n omega/sub o/t) agrees with experiment, in contrast to previous theories of Josephson tunneling

[Coping strategy and its effect on occupational stress among rail freight dispatchers].

Science.gov (United States)

Gu, Gui-zhen; Yu, Shan-fa; Li, Kui-rong; Jiang, Kai-you

2010-08-01

To analyse the relationship between coping strategy and occupational stress in rail freight dispatchers. 115 rail freight dispatchers were investigated by using group sampling method, investigation contents included coping strategies, occupational stressors, strains and personalities. The proportion of using coping strategy in rail freight dispatchers is lower. The scores of job future ambiguity, type A behavior and work locus of control in workers with insufficient coping strategy were higher than those in workers with sufficient strategy (P family balance, job involvement coping factors of coping strategy were remarkable significant (P 0.05). Logistic regression analysis showed that risk of being job dissatisfaction and daily life stress in workers with insufficient social support coping was three or four times than those with sufficient coping (OR = 3.06 or 4.38, respectively), risk of being daily life stress in workers with insufficient job involvement coping was three times than those with sufficient coping (OR = 3.26). The proportion of using coping strategy in rail freight dispatchers is lower. Coping strategy has influence on the individual's perception of occuaptional stressors, strains and personalities.

Modelling and simulation of dynamic wheel-rail interaction using a roller rig

International Nuclear Information System (INIS)

Anyakwo, A; Pislaru, C; Ball, A; Gu, F

2012-01-01

The interaction between the wheel and rail greatly influences the dynamic response of railway vehicles on the track. A roller rig facility can be used to study and monitor real time parameters that influence wheel-rail interaction such as wear, adhesion, friction and corrugation without actual field tests being carried out. This paper presents the development of the mathematical models for full scale roller rig and 1/5 scale roller rig and the wear prediction model based on KTH wear function. The simulated critical speed for the 1/5 scale roller rig is about one-fifth of the critical speed for the full scale model so the simulated results compare well with the theory related to wheel-rail contact and dynamics. Also the differences between the simulated rolling radii for the full scale model with and without wear function are analysed. This paper presents the initial stage of a large scale research project where the influence of wear on the wheel-rail performance will be studied in more depth.

Gas density and rail pressure effects on diesel spray growth from a heavy-duty common rail injector

NARCIS (Netherlands)

Klein-Douwel, R.J.H.; Frijters, P.J.M.; Seykens, X.L.J.; Somers, L.M.T.; Baert, R.S.G.

2009-01-01

Formation of nonevaporating sprays from diesel fuel injection through a realistic heavy duty multihole common rail injector is studied in a newly developed high-pressure, high-temperature cell, using digital high-speed shadowgraphy at 4500 frames/s. Gas pressure was varied from 13 to 37 bar

The influence of rail surface irregularities on contact forces and local stresses

Science.gov (United States)

Andersson, Robin; Torstensson, Peter T.; Kabo, Elena; Larsson, Fredrik

2015-01-01

The effect of initial rail surface irregularities on promoting further surface degradation is investigated. The study concerns rolling contact fatigue formation, in particular in the form of the so-called squats. The impact of surface irregularities in the form of dimples is quantified by peak magnitudes of dynamic contact stresses and contact forces. To this end simulations of two-dimensional (later extended to three-dimensional) vertical dynamic vehicle-track interaction are employed. The most influencing parameters are identified. It is shown that even very shallow dimples might have a large impact on local contact stresses. Peak magnitudes of contact forces and stresses due to the influence of rail dimples are shown to exceed those due to rail corrugation.

Quantifying economic benefits for rail infrastructure projects.