Code package {open_quotes}SVECHA{close_quotes}: Modeling of core degradation phenomena at severe accidents

Energy Technology Data Exchange (ETDEWEB)

Veshchunov, M.S.; Kisselev, A.E.; Palagin, A.V. [Nuclear Safety Institute, Moscow (Russian Federation)] [and others

1995-09-01

The code package SVECHA for the modeling of in-vessel core degradation (CD) phenomena in severe accidents is being developed in the Nuclear Safety Institute, Russian Academy of Science (NSI RAS). The code package presents a detailed mechanistic description of the phenomenology of severe accidents in a reactor core. The modules of the package were developed and validated on separate effect test data. These modules were then successfully implemented in the ICARE2 code and validated against a wide range of integral tests. Validation results have shown good agreement with separate effect tests data and with the integral tests CORA-W1/W2, CORA-13, PHEBUS-B9+.

Type B plutonium transport package development that uses metallic filaments and composite materials

International Nuclear Information System (INIS)

Pierce, J.D.; Moya, J.L.; McClure, J.D.; Hohnstreiter, G.F.; Golliher, K.G.

1992-01-01

A new design concept for a Type B transport packaging for transporting plutonium and uranium has been developed by the Transportation Systems Department at Sandia National Laboratories (SNL). The new design came about following a review of current packagings, projected future transportation needs, and current and future regulatory requirements. United States packaging, regulations specified in Title 49, Code of Federal Regulations Parts 173.416 and 173.417 (for fissile materials) offer parallel paths under the heading of authorized Type B packages for the transport of greater than A 1 or A 2 quantities of radioactive material. These pathways are for certified Type B packagings and specification packagings. Consequently, a review was made of both type B and specification packages. A request for comment has been issued by the US Nuclear Regulatory Commission (NRC) for proposed changes to Title 10, Code of Federal Regulations Part 71. These regulations may therefore change in the near future. The principle proposed regulation change that would affect this type of package is the addition of a dynamic crush requirement for certain packagings. The US Department of Transportation (DOT) may also re-evaluate the specifications in 49 CFR that authorize the fabrication and use of specification packagings. Therefore, packaging, options were considered that will meet expected new regulations and provide shipment capability for the US Department of Energy well into the future

2D edge plasma modeling extended up to the main chamber

Energy Technology Data Exchange (ETDEWEB)

Dekeyser, W., E-mail: wouter.dekeyser@mech.kuleuven.be [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Leuven (Belgium); Baelmans, M. [Department of Mechanical Engineering, Katholieke Universiteit Leuven, Celestijnenlaan 300A, 3001 Leuven (Belgium); Reiter, D.; Boerner, P.; Kotov, V. [Institut fuer Plasmaphysik, Forschungszentrum Juelich GmbH, EURATOM-Association, Trilateral Euregio Cluster, D-52425 Juelich (Germany)

2011-08-01

Far SOL plasma flow, and hence main chamber recycling and plasma surface interaction, are today still only very poorly described by current 2D fluid edge codes, such as B2, UEDGE or EDGE2D, due to a common technical limitation. We have extended the B2 plasma fluid solver in the current ITER version of B2-EIRENE (SOLPS4.3) to allow plasma solutions to be obtained up to the 'real vessel wall', at least on the basis of ad hoc far SOL transport models. We apply here the kinetic Monte Carlo Code EIRENE on such plasma solutions to study effects of this model refinement on main chamber fluxes and sputtering, for an ITER configuration. We show that main chamber sputtering may be significantly modified both due to thermalization of CX neutrals in the far SOL and poloidally highly asymmetric plasma wall contact, as compared to hitherto applied teleportation of particle fluxes across this domain.

Plasma flow measurements in the Prototype-Material Plasma Exposure eXperiment (Proto-MPEX) and comparison with B2.5-Eirene modeling

Science.gov (United States)

Kafle, N.; Owen, L. W.; Caneses, J. F.; Biewer, T. M.; Caughman, J. B. O.; Donovan, D. C.; Goulding, R. H.; Rapp, J.

2018-05-01

The Prototype Material Plasma Exposure eXperiment (Proto-MPEX) at Oak Ridge National Laboratory is a linear plasma device that combines a helicon plasma source with additional microwave and radio frequency heating to deliver high plasma heat and particle fluxes to a target. Double Langmuir probes and Thomson scattering are being used to measure local electron temperature and density at various radial and axial locations. A recently constructed Mach-double probe provides the added capability of simultaneously measuring electron temperatures ( T e), electron densities ( n e), and Mach numbers (M). With this diagnostic, it is possible to infer the plasma flow, particle flux, and heat flux at different locations along the plasma column in Proto-MPEX. Preliminary results show Mach numbers of 0.5 (towards the dump plate) and 1.0 (towards the target plate) downstream from the helicon source, and a stagnation point (no flow) near the source for the case where the peak magnetic field was 1.3 T. Measurements of particle flow and ne and Te profiles are discussed. The extensive coverage provided by these diagnostics permits data-constrained B2.5-Eirene modeling of the entire plasma column, and comparison with results of modeling in the high-density helicon plasmas will be presented.

Development of the code package KASKAD for calculations of WWERs

International Nuclear Information System (INIS)

Bolobov, P.A.; Lazarenko, A.P.; Tomilov, M.Ju.

2008-01-01

The new version of software package for neutron calculation of WWER cores KASKAD 2007 consists of some calculating and service modules, which are integrated in the common framework. The package is based on the old version, which was expanded with some new functions and the new calculating modules, such as: -the BIPR-2007 code is the new one which performs calculation of power distribution in three-dimensional geometry for 2-group neutron diffusion calculation. This code is based on the BIPR-8KN model, provides all possibilities of BIPR-7A code and uses the same input data; -the PERMAK-2007 code is pin-by-pin few-group multilayer and 3-D code for neutron diffusion calculation; -graphical user interface for input data preparation of the TVS-M code. The report also includes some calculation results obtained with modified version of the KASKAD 2007 package. (Authors)

DFT calculation for elastic constants of orthorhombic structure within WIEN2K code: A new package (ortho-elastic)

International Nuclear Information System (INIS)

Reshak, Ali H.; Jamal, Morteza

2012-01-01

Highlights: ► A new package for calculating elastic constants of orthorhombic structure is released. ► The package called ortho-elastic. ► It is compatible with [FP-(L)APW+lo] method implemented in WIEN2k code. ► Several orthorhombic structure compounds were used to test the new package. ► Elastic constants calculated using this package show good agreement with experiment. - Abstract: A new package for calculating the elastic constants of orthorhombic structure is released. The package called ortho-elastic. The formalism of calculating the ortho-elastic constants is described in details. The package is compatible with the highly accurate all-electron full-potential (linearized) augmented plane-wave plus local orbital [FP-(L)APW+lo] method implemented in WIEN2k code. Several orthorhombic structure compounds were used to test the new package. We found that the calculated elastic constants using the new package show better agreement with the available experimental data than the previous theoretical results used different methods. In this package the second-order derivative E ″ (ε) of polynomial fit E=E(ε) of energy vs strains at zero strain (ε=0), used to calculate the orthorhombic elastic constants.

A restructuring of CF package for MIDAS computer code

International Nuclear Information System (INIS)

Park, S. H.; Kim, K. R.; Kim, D. H.; Cho, S. W.

2004-01-01

CF package, which evaluates user-specified 'control functions' and applies them to define or control various aspects of computation, has been restructured for the MIDAS computer code. MIDAS is being developed as an integrated severe accident analysis code with a user-friendly graphical user interface and modernized data structure. To do this, data transferring methods of current MELCOR code are modified and adopted into the CF package. The data structure of the current MELCOR code using FORTRAN77 causes a difficult grasping of meaning of the variables as well as waste of memory, difficulty is more over because its data is location information of other package's data due to characteristics of CF package. New features of FORTRAN90 make it possible to allocate the storage dynamically and to use the user-defined data type, which lead to an efficient memory treatment and an easy understanding of the code. Restructuring of the CF package addressed in this paper includes module development, subroutine modification, and treats MELGEN, which generates data file, as well as MELCOR, which is processing a calculation. The verification has been done by comparing the results of the modified code with those from the existing code. As the trends are similar to each other, it hints that the same approach could be extended to the entire code package. It is expected that code restructuring will accelerate the code domestication thanks to direct understanding of each variable and easy implementation of modified or newly developed models

MODEL 9977 B(M)F-96 SAFETY ANALYSIS REPORT FOR PACKAGING

Energy Technology Data Exchange (ETDEWEB)

Abramczyk, G; Paul Blanton, P; Kurt Eberl, K

2006-05-18

This Safety Analysis Report for Packaging (SARP) documents the analysis and testing performed on and for the 9977 Shipping Package, referred to as the General Purpose Fissile Package (GPFP). The performance evaluation presented in this SARP documents the compliance of the 9977 package with the regulatory safety requirements for Type B packages. Per 10 CFR 71.59, for the 9977 packages evaluated in this SARP, the value of ''N'' is 50, and the Transport Index based on nuclear criticality control is 1.0. The 9977 package is designed with a high degree of single containment. The 9977 complies with 10 CFR 71 (2002), Department of Energy (DOE) Order 460.1B, DOE Order 460.2, and 10 CFR 20 (2003) for As Low As Reasonably Achievable (ALARA) principles. The 9977 also satisfies the requirements of the Regulations for the Safe Transport of Radioactive Material--1996 Edition (Revised)--Requirements. IAEA Safety Standards, Safety Series No. TS-R-1 (ST-1, Rev.), International Atomic Energy Agency, Vienna, Austria (2000). The 9977 package is designed, analyzed and fabricated in accordance with Section III of the American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel (B&PV) Code, 1992 edition.

The UK core performance code package

International Nuclear Information System (INIS)

Hutt, P.K.; Gaines, N.; McEllin, M.; White, R.J.; Halsall, M.J.

1991-01-01

Over the last few years work has been co-ordinated by Nuclear Electric, originally part of the Central Electricity Generating Board, with contributions from the United Kingdom Atomic Energy Authority and British Nuclear Fuels Limited, to produce a generic, easy-to-use and integrated package of core performance codes able to perform a comprehensive range of calculations for fuel cycle design, safety analysis and on-line operational support for Light Water Reactor and Advanced Gas Cooled Reactor plant. The package consists of modern rationalized generic codes for lattice physics (WIMS), whole reactor calculations (PANTHER), thermal hydraulics (VIPRE) and fuel performance (ENIGMA). These codes, written in FORTRAN77, are highly portable and new developments have followed modern quality assurance standards. These codes can all be run ''stand-alone'' but they are also being integrated within a new UNIX-based interactive system called the Reactor Physics Workbench (RPW). The RPW provides an interactive user interface and a sophisticated data management system. It offers quality assurance features to the user and has facilities for defining complex calculational sequences. The Paper reviews the current capabilities of these components, their integration within the package and outlines future developments underway. Finally, the Paper describes the development of an on-line version of this package which is now being commissioned on UK AGR stations. (author)

A restructuring of the MELCOR fission product packages for the MIDAS computer code

International Nuclear Information System (INIS)

Park, S.H.; Kim, K.R.; Kim, D.H.

2004-01-01

The RN1/RN2 packages, which are the fission product-related packages in MELCOR, have been restructured for the MIDAS computer code. MIDAS is being developed as an integrated severe accident analysis code with a user-friendly graphical user interface and a modernized data structure. To do this, the data transferring methods of the current MELCOR code are modified and adopted into the RN1/RN2 package. The data structure of the current MELCOR code using FORTRAN77 has a difficulty in grasping the meaning of the variables as well as waste of memory. New features of FORTRAN90 make it possible to allocate the storage dynamically and to user-defined data type, which leads to an efficient memory treatment and an easy understanding of the code. Restructuring of the RN1/RN2 package addressed in this paper includes a module development, subroutine modification, and the treatment of MELGEN, which generates the data file, as well as MELCOR, which is processing the calculation. The verification has been done by comparing the results of the modified code with those of the existing code. As the trends are similar to each other, it implies that the same approach could be extended to the entire code package. It is expected that the code restructuring will accelerate the code domestication thanks to a direct understanding of each variable and an easy implementation of the modified or newly developed models. (author)

Qualification of the coupled RELAP5/PANTHER/COBRA code package for licensing applications

International Nuclear Information System (INIS)

Schneidesch, C.R.; Zhang Jinzhao

2004-01-01

A coupled thermal hydraulics-neutronics code package has been developed at Tractebel Engineering (TE), in which the best-estimate thermal-hydraulic system code, RELAP5/mod2.5, is coupled with the full three-dimensional reactor core kinetics code, PANTHER, via the dynamic data exchange interface, TALINK. The Departure from Nucleate Boiling Ratio (DNBR) is calculated by the sub-channel thermal-hydraulic analysis code COBRA-3C. The package provides the capability to accurately simulate the key physical phenomena in nuclear power plant accidents with strong asymmetric behaviours and system-core interactions. This paper presents the TE coupled code package and focuses on the methodology followed for qualifying it for licensing applications. The qualification of the coupling demonstrated the robustness achieved by the combined 3-D neutron kinetics/system T-H code package for transient simulations. The coupled TE code package has been qualified and will be used at Tractebel Engineering (TE) for analyzing asymmetric PWR accidents with strong core-system interactions

Extensions of the 3-dimensional plasma transport code E3D

International Nuclear Information System (INIS)

Runov, A.; Schneider, R.; Kasilov, S.; Reiter, D.

2004-01-01

One important aspect of modern fusion research is plasma edge physics. Fluid transport codes extending beyond the standard 2-D code packages like B2-Eirene or UEDGE are under development. A 3-dimensional plasma fluid code, E3D, based upon the Multiple Coordinate System Approach and a Monte Carlo integration procedure has been developed for general magnetic configurations including ergodic regions. These local magnetic coordinates lead to a full metric tensor which accurately accounts for all transport terms in the equations. Here, we discuss new computational aspects of the realization of the algorithm. The main limitation to the Monte Carlo code efficiency comes from the restriction on the parallel jump of advancing test particles which must be small compared to the gradient length of the diffusion coefficient. In our problems, the parallel diffusion coefficient depends on both plasma and magnetic field parameters. Usually, the second dependence is much more critical. In order to allow long parallel jumps, this dependence can be eliminated in two steps: first, the longitudinal coordinate x 3 of local magnetic coordinates is modified in such a way that in the new coordinate system the metric determinant and contra-variant components of the magnetic field scale along the magnetic field with powers of the magnetic field module (like in Boozer flux coordinates). Second, specific weights of the test particles are introduced. As a result of increased parallel jump length, the efficiency of the code is about two orders of magnitude better. (copyright 2004 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

CONSUL code package application for LMFR core calculations

Energy Technology Data Exchange (ETDEWEB)

Chibinyaev, A.V.; Teplov, P.S.; Frolova, M.V. [RNC ' Kurchatovskiy institute' , Kurchatov sq.1, Moscow (Russian Federation)

2008-07-01

CONSUL code package designed for the calculation of reactor core characteristics has been developed at the beginning of 90's. The calculation of nuclear reactor core characteristics is carried out on the basis of correlated neutron, isotope and temperature distributions. The code package has been generally used for LWR core characteristics calculations. At present CONSUL code package was adapted to calculate liquid metal fast reactors (LMFR). The comparisons with IAEA computational test 'Evaluation of benchmark calculations on a fast power reactor core with near zero sodium void effect' and BN-1800 testing calculations are presented in the paper. The IAEA benchmark core is based on the innovative core concept with sodium plenum above the core BN-800. BN-1800 core is the next development step which is foreseen for the Russian fast reactor concept. The comparison of the operational parameters has shown good agreement and confirms the possibility of CONSUL code package application for LMFR core calculation. (authors)

A restructuring of TF package for MIDAS computer code

International Nuclear Information System (INIS)

Park, S. H.; Song, Y. M.; Kim, D. H.

2002-01-01

TF package which defines some interpolation and extrapolation condition through user defined table has been restructured in MIDAS computer code. To do this, data transferring methods of current MELCOR code are modified and adopted into TF package. The data structure of the current MELCOR code using FORTRAN77 causes a difficult grasping of the meaning of the variables as well as waste of memory. New features of FORTRAN90 make it possible to allocate the storage dynamically and to use the user-defined data type, which lead to an efficient memory treatment and an easy understanding of the code. Restructuring of TF package addressed in this paper does module development and subroutine modification, and treats MELGEN which is making restart file as well as MELCOR which is processing calculation. The validation has been done by comparing the results of the modified code with those from the existing code, and it is confirmed that the results are the same. It hints that the similar approach could be extended to the entire code package. It is expected that code restructuring will accelerate the code domestication thanks to direct understanding of each variable and easy implementation of modified or newly developed models

Survey of computer codes which produce multigroup data from ENDF/B-IV

International Nuclear Information System (INIS)

Greene, N.M.

1975-01-01

The features of three code systems that produce multigroup neutron data are contrasted. This includes the ETOE-2/MC 2 -2/SDX, MINX/SPHINX and AMPX code packages. These systems all contain a fairly extensive set of processing capabilities with the current evaluated nuclear data files--ENDF/B. They were designed with different goals and applications in mind. This paper discusses some of their differences and the implications for particular situations

Verification of 3-D generation code package for neutronic calculations of WWERs

International Nuclear Information System (INIS)

Sidorenko, V.D.; Aleshin, S.S.; Bolobov, P.A.; Bolshagin, S.N.; Lazarenko, A.P.; Markov, A.V.; Morozov, V.V.; Syslov, A.A.; Tsvetkov, V.M.

2000-01-01

Materials on verification of the 3 -d generation code package for WWERs neutronic calculations are presented. The package includes: - spectral code TVS-M; - 2-D fine mesh diffusion code PERMAK-A for 4- or 6-group calculation of WWER core burnup; - 3-D coarse mesh diffusion code BIPR-7A for 2-group calculations of quasi-stationary WWERs regimes. The materials include both TVS-M verification data and verification data on PERMAK-A and BIPR-7A codes using constant libraries generated with TVS-M. All materials are related to the fuel without Gd. TVS-M verification materials include results of comparison both with benchmark calculations obtained by other codes and with experiments carried out at ZR-6 critical facility. PERMAK-A verification materials contain results of comparison with TVS-M calculations and with ZR-6 experiments. BIPR-7A materials include comparison with operation data for Dukovany-2 and Loviisa-1 NPPs (WWER-440) and for Balakovo NPP Unit 4 (WWER-1000). The verification materials demonstrate rather good accuracy of calculations obtained with the use of code package of the 3 -d generation. (Authors)

Science version 2: the most recent capabilities of the Framatome 3-D nuclear code package

International Nuclear Information System (INIS)

Girieud, P.; Daudin, L.; Garat, C.; Marotte, P.; Tarle, S.

2001-01-01

The Framatome nuclear code package SCIENCE developed in the 1990's has been fully operational for nuclear design since 1997. Results obtained using the package demonstrate the high accuracy of its physical models. Nevertheless, since the first release of the SCIENCE package, continuous improvement work has been carried out at Framatome, which leads today to Version 2 of the package. The intensive use of the package by Framatome teams, for example, while performing reload calculations and the associated core follow, is a permanent opportunity to point out any trend or scattering in the results, even the smaller they are. Thus the main objective of improvements was to take advantage of the progress in computer performances in using more sophisticated calculation schemes conducting to more accurate results. Besides the implementation of more accurate physical models, SCIENCE Version 2 also exploits developments conducted in other fields, mainly for transient calculations using 3-D kinetics or coupling with open-channel core thermal-hydraulics and the plant simulator. These developments allow Framatome to perform accident analyses with advanced methodologies using the SCIENCE package. (author)

FUMACS-G, a Graphical User Interface for FUMACS Code Package

International Nuclear Information System (INIS)

Trontl, K.; Gergeta, K.; Smuc, T.

2002-01-01

The FUMACS (FUel MAnagement Code System) code package has been developed at Rudjer Boskovic Institute in year 1991 with the aim to enable in-core fuel management analysis of the NPP Krsko core for nominal conditions. Due to modernization and uprating of the NPP Krsko core in year 2000 and the original 1991 FUMACS inadequacy in simulating NPP Krsko core in these uprated conditions, in the year 2001 a new version of FUMACS code package has been developed - FUMACS/FEEC 2001. The code package upgrading procedure consisted of two main aspects: modifications of master files, libraries and codes necessary for proper modeling of the uprated NPP Krsko core and development of the code package structure suitable for Windows-32 environment. The latter included upgrading the source of the code from FORTRAN F77 to F90 level and development of a graphical, user-friendly interface with fully integrated electronic help system. Since the original FUMACS code package has been developed as a DOS based application, running of the code package on a Windows operating system proved to be rather inefficient and lacking in advantages of a standard Windows application. Therefore, FUMACS-G has been developed as a user friendly environment for handling off all project input and output files, as well as for easier overall project management. The design of FUMACS-G shell has been based on Microsoft application design guidelines. (author)

A restructuring of COR package for MIDAS computer code

International Nuclear Information System (INIS)

Park, S.H.; Kim, K.R.; Kim, D.H.

2004-01-01

The COR package, which calculates the thermal response of the core and the lower plenum internal structures and models the relocation of the core and lower plenum structural materials, has been restructured for the MIDAS computer code. MIDAS is being developed as an integrated severe accident analysis code with a user-friendly graphical user interface and a modernized data structure. To do this, the data transferring methods of the current MELCOR code are modified and adopted into the COR package. The data structure of the current MELCOR code using FORTRAN77 has a difficulty in grasping the meaning of the variables as well as a waste of memory. New features of FORTRAN90 make it possible to allocate the storage dynamically and to use the user-defined data type, which leads to an efficient memory treatment and an easy understanding of the code. Restructuring of the COR package addressed in this paper includes a module development, subroutine modification. The verification has been done by comparing the results of the modified code with those of the existing code. As the trends are similar to each other, it implies that the same approach could be extended to the entire code package. It is expected that the code restructuring will accelerated the code's domestication thanks to a direct understanding of each variable and an easy implementation of the modified or newly developed models. (author)

A restructuring of RN1 package for MIDAS computer code

International Nuclear Information System (INIS)

Park, S. H.; Kim, D. H.; Kim, K. R.

2003-01-01

RN1 package, which is one of two fission product-related packages in MELCOR, has been restructured for the MIDAS computer code. MIDAS is being developed as an integrated severe accident analysis code with a user-friendly graphical user interface and modernized data structure. To do this, data transferring methods of current MELCOR code are modified and adopted into the RN1 package. The data structure of the current MELCOR code using FORTRAN77 causes a difficult grasping of meaning of the variables as well as waste of memory. New features of FORTRAN90 make it possible to allocate the storage dynamically and to use the user-defined data type, which lead to an efficient memory treatment and an easy understanding of the code. Restructuring of the RN1 package addressed in this paper includes module development, subroutine modification, and treats MELGEN, which generates data file, as well as MELCOR, which is processing a calculation. The verification has been done by comparing the results of the modified code with those from the existing code. As the trends are similar to each other, it hints that the same approach could be extended to the entire code package. It is expected that code restructuring will accelerate the code domestication thanks to direct understanding of each variable and easy implementation of modified or newly developed models

Code package to analyse behavior of the WWER fuel rods in normal operation: TOPRA's code

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.

2001-01-01

This paper briefly describes the code package intended for analysis of WWER fuel rod characteristics. The package includes two computer codes: TOPRA-1 and TOPRA-2 for full-scale fuel rod analyses; MRZ and MKK codes for analyzing the separate sections of fuel rods in r-z and r-j geometry. The TOPRA's codes are developed on the base of PIN-mod2 version and verified against experimental results obtained in MR, MIR and Halden research reactors (in the framework of SOFIT, FGR-2 and FUMEX experimental programs). Comparative analysis of calculation results and results from post-reactor examination of the WWER-440 and WWER-1000 fuel rod are also made as additional verification of these codes. To avoid the enlarging of uncertainties in fuel behavior prediction as a result of simplifying of the fuel geometry, MKK and MRZ codes are developed on the basis of the finite element method with use of the three nodal finite elements. Results obtained in the course of the code verification indicate the possibility for application of the method and TOPRA's code for simplified engineering calculations of WWER fuel rods thermal-physical parameters. An analysis of maximum relative errors for predicting of the fuel rod characteristics in the range of the accepted parameter values is also presented in the paper

A QR code identification technology in package auto-sorting system

Science.gov (United States)

di, Yi-Juan; Shi, Jian-Ping; Mao, Guo-Yong

2017-07-01

Traditional manual sorting operation is not suitable for the development of Chinese logistics. For better sorting packages, a QR code recognition technology is proposed to identify the QR code label on the packages in package auto-sorting system. The experimental results compared with other algorithms in literatures demonstrate that the proposed method is valid and its performance is superior to other algorithms.

Type B Drum packages

International Nuclear Information System (INIS)

Edwards, W.S.

1995-11-01

The Type B Drum package is a container in which a single drum containing Type B quantities of radioactive material will be packaged for shipment. The Type B Drum containers are being developed to fill a void in the packaging and transportation capabilities of the US Department of Energy (DOE), as no double containment packaging for single drums of Type B radioactive material is currently available. Several multiple-drum containers and shielded casks presently exist. However, the size and weight of these containers present multiple operational challenges for single-drum shipments. The Type B Drum containers will offer one unshielded version and, if needed, two shielded versions, and will provide for the option of either single or double containment. The primary users of the Type B Drum container will be any organization with a need to ship single drums of Type B radioactive material. Those users include laboratories, waste retrieval facilities, emergency response teams, and small facilities

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1999-01-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 711 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition2. Results of the analysis and testing performed on the 9965 B, 9968 B, 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of energy (DOE) Order 5480.33 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.94 and 7.10.5

The development of the code package PERMAK--3D//SC--1

International Nuclear Information System (INIS)

Bolobov, P. A.; Oleksuk, D. A.

2011-01-01

Code package PERMAK-3D//SC-1 was developed for performing pin-by-pin coupled neutronic and thermal hydraulic calculation of the core fragment of seven fuel assemblies and was designed on the basis of 3D multigroup pin-by-pin code PERMAK-3D and 3D (subchannel) thermal hydraulic code SC-1 The code package predicts axial and radial pin-by-pin power distribution and coolant parameters in stimulated region (enthalpies,, velocities,, void fractions,, boiling and DNBR margins).. The report describes some new steps in code package development. Some PERMAK-3D//SC-1 outcomes of WWER calculations are presented in the report. (Authors)

SCAMPI: A code package for cross-section processing

International Nuclear Information System (INIS)

Parks, C.V.; Petrie, L.M.; Bowman, S.M.; Broadhead, B.L.; Greene, N.M.; White, J.E.

1996-01-01

The SCAMPI code package consists of a set of SCALE and AMPX modules that have been assembled to facilitate user needs for preparation of problem-specific, multigroup cross-section libraries. The function of each module contained in the SCANTI code package is discussed, along with illustrations of their use in practical analyses. Ideas are presented for future work that can enable one-step processing from a fine-group, problem-independent library to a broad-group, problem-specific library ready for a shielding analysis

SCAMPI: A code package for cross-section processing

Energy Technology Data Exchange (ETDEWEB)

Parks, C.V.; Petrie, L.M.; Bowman, S.M.; Broadhead, B.L.; Greene, N.M.; White, J.E.

1996-04-01

The SCAMPI code package consists of a set of SCALE and AMPX modules that have been assembled to facilitate user needs for preparation of problem-specific, multigroup cross-section libraries. The function of each module contained in the SCANTI code package is discussed, along with illustrations of their use in practical analyses. Ideas are presented for future work that can enable one-step processing from a fine-group, problem-independent library to a broad-group, problem-specific library ready for a shielding analysis.

In-core fuel management code package validation for BWRs

International Nuclear Information System (INIS)

1995-12-01

The main goal of the present CRP (Coordinated Research Programme) was to develop benchmarks which are appropriate to check and improve the fuel management computer code packages and their procedures. Therefore, benchmark specifications were established which included a set of realistic data for running in-core fuel management codes. Secondly, the results of measurements and/or operating data were also provided to verify and compare with these parameters as calculated by the in-core fuel management codes or code packages. For the BWR it was established that the Mexican Laguna Verde 1 BWR would serve as the model for providing data on the benchmark specifications. It was decided to provide results for the first 2 cycles of Unit 1 of the Laguna Verde reactor. The analyses of the above benchmarks are performed in two stages. In the first stage, the lattice parameters are generated as a function of burnup at different voids and with and without control rod. These lattice parameters form the input for 3-dimensional diffusion theory codes for over-all reactor analysis. The lattice calculations were performed using different methods, such as, Monte Carlo, 2-D integral transport theory methods. Supercell Model and transport-diffusion model with proper correction for burnable absorber. Thus the variety of results should provide adequate information for any institute or organization to develop competence to analyze In-core fuel management codes. 15 refs, figs and tabs

The HELIOS-2 lattice physics code

International Nuclear Information System (INIS)

Wemple, C.A.; Gheorghiu, H-N.M.; Stamm'ler, R.J.J.; Villarino, E.A.

2008-01-01

Major advances have been made in the HELIOS code, resulting in the impending release of a new version, HELIOS-2. The new code includes a method of characteristics (MOC) transport solver to supplement the existing collision probabilities (CP) solver. A 177-group, ENDF/B-VII nuclear data library has been developed for inclusion with the new code package. Computational tests have been performed to verify the performance of the MOC solver against the CP solver, and validation testing against computational and measured benchmarks is underway. Results to-date of the verification and validation testing are presented, demonstrating the excellent performance of the new transport solver and nuclear data library. (Author)

Verification of the CONPAS (CONtainment Performance Analysis System) code package

International Nuclear Information System (INIS)

Kim, See Darl; Ahn, Kwang Il; Song, Yong Man; Choi, Young; Park, Soo Yong; Kim, Dong Ha; Jin, Young Ho.

1997-09-01

CONPAS is a computer code package to integrate the numerical, graphical, and results-oriented aspects of Level 2 probabilistic safety assessment (PSA) for nuclear power plants under a PC window environment automatically. For the integrated analysis of Level 2 PSA, the code utilizes four distinct, but closely related modules: (1) ET Editor, (2) Computer, (3) Text Editor, and (4) Mechanistic Code Plotter. Compared with other existing computer codes for Level 2 PSA, and CONPAS code provides several advanced features: computational aspects including systematic uncertainty analysis, importance analysis, sensitivity analysis and data interpretation, reporting aspects including tabling and graphic as well as user-friendly interface. The computational performance of CONPAS has been verified through a Level 2 PSA to a reference plant. The results of the CONPAS code was compared with an existing level 2 PSA code (NUCAP+) and the comparison proves that CONPAS is appropriate for Level 2 PSA. (author). 9 refs., 8 tabs., 14 figs

Nupack, the new ASME code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as Nupack, has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used for the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper

Abstracts of digital computer code packages. Assembled by the Radiation Shielding Information Center. [Radiation transport codes

Energy Technology Data Exchange (ETDEWEB)

McGill, B.; Maskewitz, B.F.; Anthony, C.M.; Comolander, H.E.; Hendrickson, H.R.

1976-01-01

The term ''code package'' is used to describe a miscellaneous grouping of materials which, when interpreted in connection with a digital computer, enables the scientist--user to solve technical problems in the area for which the material was designed. In general, a ''code package'' consists of written material--reports, instructions, flow charts, listings of data, and other useful material and IBM card decks (or, more often, a reel of magnetic tape) on which the source decks, sample problem input (including libraries of data) and the BCD/EBCDIC output listing from the sample problem are written. In addition to the main code, and any available auxiliary routines are also included. The abstract format was chosen to give to a potential code user several criteria for deciding whether or not he wishes to request the code package. (RWR)

Status of reactor core design code system in COSINE code package

Energy Technology Data Exchange (ETDEWEB)

Chen, Y.; Yu, H.; Liu, Z., E-mail: yuhui@snptc.com.cn [State Nuclear Power Software Development Center, SNPTC, National Energy Key Laboratory of Nuclear Power Software (NEKLS), Beijiing (China)

2014-07-01

For self-reliance, COre and System INtegrated Engine for design and analysis (COSINE) code package is under development in China. In this paper, recent development status of the reactor core design code system (including the lattice physics code and the core simulator) is presented. The well-established theoretical models have been implemented. The preliminary verification results are illustrated. And some special efforts, such as updated theory models and direct data access application, are also made to achieve better software product. (author)

Status of reactor core design code system in COSINE code package

International Nuclear Information System (INIS)

Chen, Y.; Yu, H.; Liu, Z.

2014-01-01

For self-reliance, COre and System INtegrated Engine for design and analysis (COSINE) code package is under development in China. In this paper, recent development status of the reactor core design code system (including the lattice physics code and the core simulator) is presented. The well-established theoretical models have been implemented. The preliminary verification results are illustrated. And some special efforts, such as updated theory models and direct data access application, are also made to achieve better software product. (author)

A restructuring of the FL package for the MIDAS computer code

International Nuclear Information System (INIS)

Park, S. H.; Kim, K. R.; Kim, D. H.; Cho, S. W.

2005-01-01

The developmental need for a localized severe accident analysis code is on the rise, and KAERI is developing a severe accident code MIDAS, based on MELCOR. The existing data saving method uses pointer variables for a fix-sized storage management, and it deteriorates the readability, maintainability and portability of the code. But new features in FORTRAN90 such as a dynamic allocation have been used for the restructuring. The restructuring of the data saving and transferring method of the existing code makes it easy to understand the code. Before an entire restructuring of the code, a restructuring template for a simple package was developed and tested. The target for the restructuring was the FL package which is responsible for modeling the thermal-hydraulic behavior of a liquid water, water vapor, and gases in MELCOR with the CVH package. The verification was done through comparing the results before and after the restructuring

Utility subroutine package used by Applied Physics Division export codes

International Nuclear Information System (INIS)

Adams, C.H.; Derstine, K.L.; Henryson, H. II; Hosteny, R.P.; Toppel, B.J.

1983-04-01

This report describes the current state of the utility subroutine package used with codes being developed by the staff of the Applied Physics Division. The package provides a variety of useful functions for BCD input processing, dynamic core-storage allocation and managemnt, binary I/0 and data manipulation. The routines were written to conform to coding standards which facilitate the exchange of programs between different computers

Windows user-friendly code package development for operation of research reactors

International Nuclear Information System (INIS)

Hoang Anh Tuan

1998-01-01

The content of the project was to developed: 1. MS Windows interface to spectral codes like THERMOS, PEACO-COLLIS, GRACE and burn-up code. 2. MS Windows C-language burn-up diffusion hexagonal lattice code. The overall scope of the project was to develop a PC-based MS Windows code package for operation of Dalat research reactor. Various problems relating to neutronic physics like thermalization, resonance treatment, fast spectral treatment, change of isotopic concentration during burn-up time as well as burn-up distribution in the reactor core are considered in parallel to application of informatics technique. The developing process is a subject of the concept of user-friendly interface between end-users and the code package. High level input features through system of icon, menu, dialog box with regard to Common User Access (CUA) convention and sophisticated graphical output in MS Windows environment was used. The user-computer interface is also enhanced by using both keyboard and mouse, which creates a very natural manner for end-user. (author)

A restructuring of the CF/EDF packages for the MIDAS computer code

International Nuclear Information System (INIS)

Park, S.H.; Kim, K.R.; Kim, D.H.

2004-01-01

The CF and EDF packages, which allow the user to define the functions of variables in a database and the usage of an external data file, have been restructured for the MIDAS computer code. MIDAS is being developed as an integrated severe accident analysis code with a user-friendly graphical user interface and a modernized data structure. To restructure the code, the data transferring methods of the current MELCOR code are modified and then partially adopted into the CF/EDF packages. The data structure of the current MELCOR code using FORTRAN77 has a difficulty in grasping the meaning of the variables as pointers are used to define their addresses. New features of FORTRAN90 make it possible to allocate the storage dynamically and to use the user-defined data type without pointers leading to an efficient memory treatment and an easy understanding of the code. Restructuring of the CF/EDF packages addressed in this paper includes a module development and subroutine modification. The verification has been done by comparing the results of the modified code with those of the existing code and the trends are almost the same to each other. Therefore the similar approach could be extended to the entire code package for code restructuring. It is expected that the code restructuring will accelerate the code's domestication thanks to a direct understanding of each variable and an easy implementation of the modified or newly developed models. (author)

Plasma diagnostics package. Volume 2: Spacelab 2 section. Part B: Thesis projects

Science.gov (United States)

Pickett, Jolene S. (Compiler); Frank, L. A. (Compiler); Kurth, W. S. (Compiler)

1988-01-01

This volume (2), which consists of two parts (A and B), of the Plasma Diagnostics Package (PDP) Final Science Report contains a summary of all of the data reduction and scientific analyses which were performed using PDP data obtained on STS-51F as a part of the Spacelab 2 (SL-2) payload. This work was performed during the period of launch, July 29, 1985, through June 30, 1988. During this period the primary data reduction effort consisted of processing summary plots of the data received by 12 of the 14 instruments located on the PDP and submitting these data to the National Space Science Data Center (NSSDC). Three Master's and three Ph.D. theses were written using PDP instrumentation data. These theses are listed in Volume 2, Part B.

Nupack, the new Asme code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as 'Nupack', has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper. Participation in the Nupack development work described in this paper was supported by the U.S. Department of Energy. (authors)

Implementing and Testing the LINTAB, HEATER and PLOTTAB code package

International Nuclear Information System (INIS)

Cullen, D.E.; Smith, J.J.

1987-07-01

Enclosed is a description of the magnetic tape or floppy diskette containing the LINTAB, HEATER and PLOTTAB code package. In addition detailed information is provided on implementation and testing of these codes. These codes are documented in IAEA-NDS-84. (author)

Dynamics of three-dimensional radiative structures during RMP assisted detached plasmas on the large helical device and its comparison with EMC3-EIRENE modeling

Science.gov (United States)

Pandya, Shwetang N.; Peterson, Byron J.; Kobayashi, Masahiro; Ida, Katsumi; Mukai, Kiyofumi; Sano, Ryuichi; Miyazawa, Junichi; Tanaka, Hirohiko; Masuzaki, Suguru; Akiyama, Tsuyoshi; Motojima, Gen; Ohno, Noriyasu; LHD Experiment Group

2016-04-01

The resonant magnetic perturbation (RMP) island introduced in the stochastic edge of the large helical device (LHD) plasma plays an important role in the stabilization of the plasma detachment (Kobayashi et al 2013 Nucl. Fusion 53 093032). The plasma enters in the sustained detachment phase in the presence of an RMP once the line averaged density exceeds a critical value with a given input power. During detachment the enhanced radiation from the stochastic edge of the LHD undergoes several spatiotemporal changes which are studied quantitatively by an infrared imaging video bolometer (IRVB) diagnostic. The experimental results are compared qualitatively and quantitatively with the radiation predicted by the 3D transport simulation with fluid model, EMC3-EIRENE. A fair amount of qualitative agreement, before and after the detachment, is reported. The issue of overestimated radiation from the model is addressed by changing the free parameters in the EMC3-EIRENE code till the total radiation and the radiation profiles match closely, within a factor of two with the experimental observations. A better quantitative match between the model and the experiment is achieved at higher cross-field impurity diffusion coefficient and lower sputtering coefficient after the detachment. In this article a comparison, the first of its kind, is established between the quantified radiation from the experiments and the synthetic image obtained from the simulation code. This exercise is aimed towards validating the model assumptions against the experimentally measured radiation.

Type B liquid package technical issues -- Experience with LR-56 safety analysis

International Nuclear Information System (INIS)

Smith, A.C.; Alstine, M.N. van; Gromada, R.J.; Hensel, S.J.; Gupta, N.K.

1997-01-01

In the course of the development of nuclear industry in France, shipment of Type B quantities (i.e., quantities having significant radiological consequences) of radioactive liquids between different, sites became necessary. Based on the experience acquired at the Commissariat a l'Energie Atomique (CEA) nuclear centers, a series of tanker trailers has been developed to meet this need. Similarly, as part of the ongoing program to process wastes to stable end forms, a need exists to move radioactive liquids at several DOE sites. The LR-56, developed by CEA to transport liquids of medium to high activity, was selected for these US applications, based on its design features and successful operating experience in France. No comparable Type B liquid packages are certified in the US Packages employed in transport of Type B quantities of liquids are either only suitable for small volumes, or are used within site boundaries with extensive administrative controls employed to insure that an adequate level of safety is maintained. The requirement is to provide safety equivalent to the level established by federal regulations in 10 CFR 71. Type B radioactive materials packages (RAM packages) are typically simple, rugged containers which are designed and fabricated in accordance with the ASME Boiler and Pressure Vessel Code to provide containment under the normal conditions of transport (NCT) and hypothetical accident conditions (HAC) established by the regulations. Packages designed for liquid contents must address a number of technical issues which are not common to packages for solid contents. This paper reviews the technical issues associated with Type B liquid packages from the perspective of the experience gained from the evaluation of the LR-56 for use at DOE sites

A Restructuring of the CAV and FDI Package for the MIDAS Computer Code

International Nuclear Information System (INIS)

Park, S. H.; Kim, D. H.; Cho, S. W.

2006-01-01

As one of the processes for a localized severe accident analysis code, KAERI is developing a severe accident code MIDAS. The MIDAS code is being developed based on MELCOR. The existing data saving method of MELCOR uses pointer variables for a fix-sized storage management, and it deteriorates the readability, maintainability and portability of the code. As a most important process for a localized severe accident analysis code, it is needed convenient method for data handling. So, it has been used the new features in FORTRAN90 such as a dynamic allocation for the restructuring. The restructuring of the data saving and transferring method of the existing code makes it easy to understand the code. Before an entire restructuring of the code, a restructuring template for a simple package was developed and tested. The target for the restructuring in this paper was the CAV and FDI packages. The CAV(cavity) package is responsible for modeling the attack on the basement concrete by hot core materials. The FDI(Fuel Dispersal Interactions) package is responsible for modeling both low and high pressure molten fuel ejection from the RPV into the reactor cavity, control volumes and surfaces. The verification was done through comparing the results before and after the restructuring

Abstracts of digital computer code packages. Assembled by the Radiation Shielding Information Center

International Nuclear Information System (INIS)

McGill, B.; Maskewitz, B.F.; Anthony, C.M.; Comolander, H.E.; Hendrickson, H.R.

1976-01-01

The term ''code package'' is used to describe a miscellaneous grouping of materials which, when interpreted in connection with a digital computer, enables the scientist--user to solve technical problems in the area for which the material was designed. In general, a ''code package'' consists of written material--reports, instructions, flow charts, listings of data, and other useful material and IBM card decks (or, more often, a reel of magnetic tape) on which the source decks, sample problem input (including libraries of data) and the BCD/EBCDIC output listing from the sample problem are written. In addition to the main code, and any available auxiliary routines are also included. The abstract format was chosen to give to a potential code user several criteria for deciding whether or not he wishes to request the code package

Type B drum packages

International Nuclear Information System (INIS)

McCoy, J.C.

1994-08-01

The Type B drum packages (TBD) are conceptualized as a family of containers in which a single 208 L or 114 L (55 gal or 30 gal) drum containing Type B quantities of radioactive material (RAM) can be packaged for shipment. The TBD containers are being developed to fill a void in the packaging and transportation capabilities of the U.S. Department of Energy as no container packaging single drums of Type B RAM exists offering double containment. Several multiple-drum containers currently exist, as well as a number of shielded casks, but the size and weight of these containers present many operational challenges for single-drum shipments. As an alternative, the TBD containers will offer up to three shielded versions (light, medium, and heavy) and one unshielded version, each offering single or optional double containment for a single drum. To reduce operational complexity, all versions will share similar design and operational features where possible. The primary users of the TBD containers are envisioned to be any organization desiring to ship single drums of Type B RAM, such as laboratories, waste retrieval activities, emergency response teams, etc. Currently, the TBD conceptual design is being developed with the final design and analysis to be completed in 1995 to 1996. Testing and certification of the unshielded version are planned to be completed in 1996 to 1997 with production to begin in 1997 to 1998

Packaging design criteria for the Type B Drum

International Nuclear Information System (INIS)

Edwards, W.S.; Smith, R.J.; Wells, A.H.

1995-09-01

The Type B Drum package is a transportation cask capable of shipping a single 55-gal (208 L) drum of transuranic (TRU) waste. The Type B Drum is smaller than existing certified packages, such as the TRUPACT-II cask, but will allow payloads with higher thermal and gas generation rates, thus providing greater operational flexibility. The Type B Drum package has double containment so that plutonium contents and other radioactive material may be transported in Type B quantities. Conceptual designs of unshielded and shielded versions of the Type B Drum were completed in Report on the Conceptual Design of the Unshielded Type B Drum Packaging and Report on the Conceptual Design of the Shielded type B Drum Packaging (WEC 1994a, WEC 1994b), which demonstrated the Type B Drum to be a viable packaging system. A Type B package containment system must withstand the normal conditions of transport and the hypothetical accident conditions, which include a 9-m (30-ft) drop onto an unyielding surface and a 1-m (3-ft) drop onto a 15-cm (6-in.) diameter pin, and a fire and immersion scenarios

A Restructuring of the HS Package for the MIDAS Computer Code

International Nuclear Information System (INIS)

Park, S. H.; Kim, K. R.; Kim, D. H.; Cho, S. W.

2005-01-01

As one of the processes for a localized severe accident analysis code, KAERI is developing a severe accident code MIDAS, based on MELCOR. The existing data saving method uses pointer variables for a fix-sized storage management, and it deteriorates the readability, maintainability and portability of the code. But new features in FORTRAN90 such as a dynamic allocation have been used for the restructuring. The restructuring of the data saving and transferring method of the existing code makes it easy to understand the code. Before an entire restructuring of the code, a restructuring template for a simple package was developed and tested. The target for the restructuring was the HS package which is responsible for calculation the heat conduction within an intact, solid structure and energy transfer across its boundary surfaces into control volumes. The verification was done through comparing the results before and after the restructuring

EMC3-EIRENE modeling of toroidally-localized divertor gas injection experiments on Alcator C-Mod

Energy Technology Data Exchange (ETDEWEB)

Lore, J.D., E-mail: lorejd@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN 37831 (United States); Reinke, M.L. [York Plasma Institute, Department of Physics, University of York, Heslington, York YO10 5DD (United Kingdom); LaBombard, B. [Plasma Science and Fusion Center, MIT, Cambridge, MA 02139 (United States); Lipschultz, B. [York Plasma Institute, Department of Physics, University of York, Heslington, York YO10 5DD (United Kingdom); Churchill, R.M. [Plasma Science and Fusion Center, MIT, Cambridge, MA 02139 (United States); Pitts, R.A. [ITER Organization, Route de Vinon sur Verdon, 13115 Saint Paul Lez Durance (France); Feng, Y. [Max Planck Institute for Plasma Physics, Greifswald (Germany)

2015-08-15

Experiments on Alcator C-Mod with toroidally and poloidally localized divertor nitrogen injection have been modeled using the three-dimensional edge transport code EMC3-EIRENE to elucidate the mechanisms driving measured toroidal asymmetries. In these experiments five toroidally distributed gas injectors in the private flux region were sequentially activated in separate discharges resulting in clear evidence of toroidal asymmetries in radiated power and nitrogen line emission as well as a ∼50% toroidal modulation in electron pressure at the divertor target. The pressure modulation is qualitatively reproduced by the modeling, with the simulation yielding a toroidal asymmetry in the heat flow to the outer strike point. Toroidal variation in impurity line emission is qualitatively matched in the scrape-off layer above the strike point, however kinetic corrections and cross-field drifts are likely required to quantitatively reproduce impurity behavior in the private flux region and electron temperatures and densities directly in front of the target.

Benchmarking of the computer code and the thirty foot side drop analysis for the Shippingport (RPV/NST package)

International Nuclear Information System (INIS)

Bumpus, S.E.; Gerhard, M.A.; Hovingh, J.; Trummer, D.J.; Witte, M.C.

1989-01-01

This paper presents the benchmarking of a finite element computer code and the subsequent results from the code simulating the 30 foot side drop impact of the RPV/NST transport package from the decommissioned Shippingport Nuclear Power Station. The activated reactor pressure vessel (RPV), thermal shield, and other reactor external components were encased in concrete contained by the neutron shield tank (NST) and a lifting skirt. The Shippingport RPV/NST package, a Type B Category II package, weighs approximately 900 tons and has 17.5 ft diameter and 40.7 ft. length. For transport of the activated components from Shippingport to the burial site, the Safety Analysis Report for Packaging (SARP) demonstrated that the package can withstand the hypothetical accidents of DOE Order 5480.3 including 10 CFR 71. Mathematical simulations of these accidents can substitute for actual tests if the simulated results satisfy the acceptance criteria. Any such mathematical simulation, including the modeling of the materials, must be benchmarked to experiments that duplicate the loading conditions of the tests. Additional confidence in the simulations is justified if the test specimens are configured similar to the package

Influenza A and B Virus Intertypic Reassortment through Compatible Viral Packaging Signals

Science.gov (United States)

Baker, Steven F.; Nogales, Aitor; Finch, Courtney; Tuffy, Kevin M.; Domm, William; Perez, Daniel R.; Topham, David J.

2014-01-01

gene exchange between influenza A and B viruses is not well understood. Nucleotides comprising the coding termini of each influenza A virus gene segment are required for specific segment incorporation during budding. Whether influenza B virus shares a similar selective packaging strategy or if packaging signals prevent intertypic reassortment remains unknown. Here, we provide evidence suggesting a similar mechanism of influenza B virus genome packaging. Furthermore, by appending influenza A virus packaging signals onto influenza B virus segments, we rescued recombinant influenza A/B viruses that could reassort in vitro with another influenza A virus. These findings suggest that the divergent evolution of packaging signals aids with the speciation of influenza A and B viruses and is in part responsible for the lack of intertypic viral reassortment. PMID:25008914

Safety analysis report - packages 9965, 9968, 9972-9975 packages

International Nuclear Information System (INIS)

Van Alstine, M.N.

1997-10-01

This Safety Analysis Report for Packaging (SARP) documents the performance of the 9965 B( ), 9968 B( ), 9972 B(U), 9973 B(U), 9974 B(U), and 9975 B(U) packages in satisfying the regulatory safety requirements of the Code of Federal Regulations (CFR) 10 CFR 71 and the International Atomic Energy Agency (IAEA) Safety Series No. 6, Regulations for the Safe Transport of Radioactive Material, 1985 edition. Results of the analysis and testing performed on the 9965 B(), 9968 B(), 9972 B(U), 9973 B(U), and 9975 B(U) packages are presented in this SARP, which was prepared in accordance with U.S. Department of Energy (DOE) Order 5480.3 and in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guides 7.9 and 7.10

Development of a PC code package for the analysis of research and power reactors

International Nuclear Information System (INIS)

Urli, N.

1992-06-01

Computer codes available for performing reactor physics calculations for nuclear research reactors and power reactors are normally suited for running on mainframe computers. With the fast development in speed and memory of the PCs and affordable prices it became feasible to develop PC versions of commonly used codes. The present work performed under an IAEA sponsored research contract has successfully developed a code package for running on a PC. This package includes a cross-section generating code PSU-LEOPARD and 2D and 1D spatial diffusion codes, MCRAC and MCYC 1D. For adapting PSU-LEOPARD for a PC, the binary library has been reorganized to decimal form, upgraded to FORTRAN-77 standard and arrays and subroutines reorganized to conform to PC compiler. Similarly PC version of MCRAC for FORTRAN-77 and 1D code MCYC 1D have been developed. Tests, verification and bench mark results show excellent agreement with the results obtained from mainframe calculations. The execution speeds are also very satisfactory. 12 refs, 4 figs, 3 tabs

CEPXS/ONELD: A one-dimensional coupled electron-photon discrete ordinates code package

International Nuclear Information System (INIS)

Lorence, L.J. Jr.; Morel, J.E.

1992-01-01

CEPXS/ONELD is a discrete ordinates transport code package that can model the electron-photon cascade from 100 MeV to 1 keV. The CEPXS code generates fully-coupled multigroup-Legendre cross section data. This data is used by the general-purpose discrete ordinates code, ONELD, which is derived from the Los Alamos ONEDANT and ONBTRAN codes. Version 1.0 of CEPXS/ONELD was released in 1989 and has been primarily used to analyze the effect of radiation environments on electronics. Version 2.0 is under development and will include user-friendly features such as the automatic selection of group structure, spatial mesh structure, and S N order

Verification of a BWR code package by gamma scan measurements

International Nuclear Information System (INIS)

Nakajima, Tsuyoshi; Iwamoto, Tatsuya; Kumanomido, Hironori

1996-01-01

High-burnup 8 x 8 fuel with a large central water rod (called step 2 fuel) has been recently introduced to the latest Japanese boiling water reactor (BWR) plants. Lanthanum-140 gamma intensity is almost directly related to nodal powers. By gamma scan measurement, the axial distribution of 140 La in the exposed fuel was measured at the end of cycle (EOC) 1 and was compared with the calculation by a BWR code package TGBLA/LOGOS. The multienrichment fuel-type core (MEC) design was adopted for the initial cycle core of the plants. The MEC design contains three different enrichment types of fuels to simulate the equilibrium cycles, achieve much higher discharge exposure, and save fuel cycle cost, and the low-enrichment fuels are loaded in periphery and in control cells. Such MEC design could be a challenge to the BWR design methods because of the large spectrum mismatch among the fuel assemblies of the different enrichments. The aforementioned comparison has shown that the accuracy of the TGBLA/LOGOS code package is satisfactory

Code Disentanglement: Initial Plan

Energy Technology Data Exchange (ETDEWEB)

Wohlbier, John Greaton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kelley, Timothy M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rockefeller, Gabriel M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Calef, Matthew Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-01-27

The first step to making more ambitious changes in the EAP code base is to disentangle the code into a set of independent, levelized packages. We define a package as a collection of code, most often across a set of files, that provides a defined set of functionality; a package a) can be built and tested as an entity and b) fits within an overall levelization design. Each package contributes one or more libraries, or an application that uses the other libraries. A package set is levelized if the relationships between packages form a directed, acyclic graph and each package uses only packages at lower levels of the diagram (in Fortran this relationship is often describable by the use relationship between modules). Independent packages permit independent- and therefore parallel|development. The packages form separable units for the purposes of development and testing. This is a proven path for enabling finer-grained changes to a complex code.

The spectral code Apollo2: from lattice to 2D core calculations

International Nuclear Information System (INIS)

Coste-Delclaux, M.; Santandrea, S.; Damian, F.; Blanc-Tranchant, P.; Zmijarevic, I.; Santamarina, A.

2005-01-01

Apollo2 is a powerful code dedicated to neutron transport, it is a highly qualified tool for a wide range of applications from research and development studies to industrial applications. Today Apollo2 is part of several advanced 3-dimensional nuclear code packages dedicated to reactor physics, fuel cycle, criticality and safety analysis. The presentations have been organized into 7 topics: -) an introduction to Apollo2, -) cross-sections, -) flux calculation, -) advanced applications, -) Apollo2 users, specialized packages, -) qualification program, and -) the future of Apollo2. This document gathers only the slides of the presentations

The spectral code Apollo2: from lattice to 2D core calculations

Energy Technology Data Exchange (ETDEWEB)

Coste-Delclaux, M.; Santandrea, S.; Damian, F.; Blanc-Tranchant, P.; Zmijarevic, I. [CEA Saclay (DEN/DANS/SERMA), 91 - Gif-sur-Yvette (France); Santamarina, A. [CEA Cadarache (CEA/DEN/DER/SPRC), 13 - Saint Paul lez Durance (France)

2005-07-01

Apollo2 is a powerful code dedicated to neutron transport, it is a highly qualified tool for a wide range of applications from research and development studies to industrial applications. Today Apollo2 is part of several advanced 3-dimensional nuclear code packages dedicated to reactor physics, fuel cycle, criticality and safety analysis. The presentations have been organized into 7 topics: -) an introduction to Apollo2, -) cross-sections, -) flux calculation, -) advanced applications, -) Apollo2 users, specialized packages, -) qualification program, and -) the future of Apollo2. This document gathers only the slides of the presentations.

The TE coupled RELAP5/PANTHER/COBRA code package and methodology for integrated PWR accident analysis

International Nuclear Information System (INIS)

Schneidesch, Christophe R.; Zhang, Jinzhao; Ammirabile, Luca; Dalleur, Jean-Paul

2006-01-01

At Tractebel Engineering (TE), a dynamic coupling has been developed between the best estimate thermal hydraulics system code RELAP5 and the 3-dimensional neutronics code PANTHER via the transient analysis code linkage program TALINK. An interface between PANTHER and the subchannel core thermal-hydraulic analysis code COBRA 3C has been established for on-line calculation of the Departure from Nucleate Boiling Ratio (DNBR). In addition to the standard RELAP5-PANTHER coupling, the fully dynamic coupling of the RELAP5/PANTHER/COBRA3C-TE code package can be activated for evaluation purposes in which the PANTHER close-channel thermal-hydraulics module is replaced by the COBRA3C-TE with cross flow modelling and extended T-H flow conditions capabilities. The qualification of the RELAP5-PANTHER coupling demonstrated the robustness achieved by the combined 3-D neutron kinetics/system T-H code package for transient simulations. The coupled TE code package has been approved by the Belgian Safety Authorities and is used at TE for analyzing asymmetric PWR accidents with strong core-system interactions. In particular, the TE coupled code package was first used to develop a main steam line break in hot shutdown conditions (SLBHZP) accident analysis methodology based on the TE deterministic bounding approach. This methodology has been reviewed and accepted by the Belgian Safety Authorities for specific applications. Those specific applications are related to the power up-rate and steam generator replacement project of the Doel 2 plant or to the Tihange-3 SLB accident re-analysis. A coupled feedwater line break (FLB) accident analysis methodology is currently being reviewed for application approval. The results of coupled thermal-hydraulic and neutronic analysis of SLB and FLB show that there exist important margins in the traditional final safety analysis report (FSAR) accident analysis. Those margins can be used to increase the operational flexibility of the plants. Moreover, the

The TE coupled RELAP5/PANTHER/COBRA code package and methodology for integrated PWR accident analysis

Energy Technology Data Exchange (ETDEWEB)

Schneidesch, Christophe R.; Zhang, Jinzhao; Ammirabile, Luca; Dalleur, Jean-Paul [Suez-Tractebel Engineering, Avenue Ariane 7, B-1200 Brussels (Belgium)

2006-07-01

At Tractebel Engineering (TE), a dynamic coupling has been developed between the best estimate thermal hydraulics system code RELAP5 and the 3-dimensional neutronics code PANTHER via the transient analysis code linkage program TALINK. An interface between PANTHER and the subchannel core thermal-hydraulic analysis code COBRA 3C has been established for on-line calculation of the Departure from Nucleate Boiling Ratio (DNBR). In addition to the standard RELAP5-PANTHER coupling, the fully dynamic coupling of the RELAP5/PANTHER/COBRA3C-TE code package can be activated for evaluation purposes in which the PANTHER close-channel thermal-hydraulics module is replaced by the COBRA3C-TE with cross flow modelling and extended T-H flow conditions capabilities. The qualification of the RELAP5-PANTHER coupling demonstrated the robustness achieved by the combined 3-D neutron kinetics/system T-H code package for transient simulations. The coupled TE code package has been approved by the Belgian Safety Authorities and is used at TE for analyzing asymmetric PWR accidents with strong core-system interactions. In particular, the TE coupled code package was first used to develop a main steam line break in hot shutdown conditions (SLBHZP) accident analysis methodology based on the TE deterministic bounding approach. This methodology has been reviewed and accepted by the Belgian Safety Authorities for specific applications. Those specific applications are related to the power up-rate and steam generator replacement project of the Doel 2 plant or to the Tihange-3 SLB accident re-analysis. A coupled feedwater line break (FLB) accident analysis methodology is currently being reviewed for application approval. The results of coupled thermal-hydraulic and neutronic analysis of SLB and FLB show that there exist important margins in the traditional final safety analysis report (FSAR) accident analysis. Those margins can be used to increase the operational flexibility of the plants. Moreover, the

Plasma diagnostics package. Volume 2: Spacelab 2 section. Part B: Thesis projects. Final science report

International Nuclear Information System (INIS)

Pickett, J.S.; Frank, L.A.; Kurth, W.S.

1988-06-01

This volume (2), which consists of two parts (A and B), of the Plasma Diagnostics Package (PDP) Final Science Report contains a summary of all of the data reduction and scientific analyses which were performed using PDP data obtained on STS-51F as a part of the Spacelab 2 (SL-2) payload. This work was performed during the period of launch, July 29, 1985, through June 30, 1988. During this period the primary data reduction effort consisted of processing summary plots of the data received by 12 of the 14 instruments located on the PDP and submitting these data to the National Space Science Data Center (NSSDC). Three Master's and three Ph.D. theses were written using PDP instrumentation data. These theses are listed in Volume 2, Part B

B2.5-Eunomia simulations of Pilot-PSI plasmas

International Nuclear Information System (INIS)

Wieggers, R.C.; Coster, D.P.; Groen, P.W.C.; Blank, H.J. de; Goedheer, W.J.

2013-01-01

The B2.5-Eunomia code is used to simulate the plasma and neutral species in and around a Pilot-PSI plasma beam. B2.5, part of the SOLPS5.0 code package, is a multi-fluid plasma code for the scrape-off layer. Eunomia is a newly developed non-linear Monte Carlo transport code that solves the neutral equilibrium, given a background plasma. Eunomia is developed to simulate the relevant neutral species in Pilot-PSI and Magnum-PSI, linear devices that study plasma surface interactions in conditions expected in the ITER divertor. Results show the influence of the neutral species on the Pilot-PSI plasma beam. We show that a fluid description for the neutrals is not sufficient and Eunomia is needed to describe Pilot-PSI. The treatment of individual vibrational states of molecular hydrogen as separate species is crucial to match the experiment

Development of platform to compare different wall heat transfer packages for system analysis codes

International Nuclear Information System (INIS)

Kim, Min-Gil; Lee, Won Woong; Lee, Jeong Ik; Shin, Sung Gil

2016-01-01

System thermal hydraulic (STH) analysis code is used for analyzing and evaluating the safety of a designed nuclear system. The system thermal hydraulic analysis code typically solves mass, momentum and energy conservation equations for multiple phases with sets of selected empirical constitutive equations to close the problem. Several STH codes are utilized in academia, industry and regulators, such as MARS-KS, SPACE, RELAP5, COBRA-TF, TRACE, and so on. Each system thermal hydraulic code consists of different sets of governing equations and correlations. However, the packages and sets of correlations of each code are not compared quantitatively yet. Wall heat transfer mode transition maps of SPACE and MARS-KS have a little difference for the transition from wall nucleate heat transfer mode to wall film heat transfer mode. Both codes have the same heat transfer packages and correlations in most region except for wall film heat transfer mode. Most of heat transfer coefficients calculated for the range of selected variables of SPACE are the same with those of MARS-KS. For the intervals between 500K and 540K of wall temperature, MARS-KS selects the wall film heat transfer mode and Bromley correlation but SPACE select the wall nucleate heat transfer mode and Chen correlation. This is because the transition from nucleate boiling to film boiling of MARS-KS is earlier than SPACE. More detailed analysis of the heat transfer package and flow regime package will be followed in the near future

A 3D Monte Carlo code for plasma transport in island divertors

International Nuclear Information System (INIS)

Feng, Y.; Sardei, F.; Kisslinger, J.; Grigull, P.

1997-01-01

A fully 3D self-consistent Monte Carlo code EMC3 (edge Monte Carlo 3D) for modelling the plasma transport in island divertors has been developed. In a first step, the code solves a simplified version of the 3D time-independent plasma fluid equations. Coupled to the neutral transport code EIRENE, the EMC3 code has been used to study the particle, energy and neutral transport in W7-AS island divertor configurations. First results are compared with data from different diagnostics (Langmuir probes, H α cameras and thermography). (orig.)

Validation of the REL2005 code package on Gd-poisoned PWR type assemblies through the CAMELEON experimental program

International Nuclear Information System (INIS)

Blaise, Patrick; Vidal, Jean-Francois; Santamarina, Alain

2009-01-01

This paper details the validation of Gd-poisoned 17x17 PWR lattices, through several configurations of the CAMELEON experimental program, by using the newly qualified REL2005 French code package. After a general presentation of the CAMELEON program that took place in the EOLE critical Facility in Cadarache, one describes the new REL2005 code package relying on the deterministic transport code APOLLO2.8 based on characteristics method (MOC), and its new CEA2005 library based on the latest JEFF-3.1.1 nuclear data evaluation. For critical masses, the average Calculation-to-Experiment C/E's on the k eff are (136 ± 80) pcm and (300 ± 76) pcm for the reference 281 groups MOC and optimized 26 groups MOC schemes respectively. These values include also a drastic improvement of about 250 pcm due to the change in the library from JEF2.2 to JEFF3.1. For pin-by-pin radial power distributions, reference and REL2005 results are very close, with maximum discrepancies of the order of 2%, i.e., in the experimental uncertainty limits. The Optimized REL2005 code package allows to predict the reactivity worth of the Gd-clusters (averaged on 9 experimental configurations) to be C/E Δρ(Gd clusters) = +1.3% ± 2.3%. (author)

Code Package to Analyze Parameters of the WWER Fuel Rod. TOPRA-2 Code - Verification Data

International Nuclear Information System (INIS)

Scheglov, A.; Proselkov, V.; Passage, G.; Stefanova, S.

2009-01-01

Presented are the data for computer codes to analyze WWER fuel rods, used in the WWER department of RRC 'Kurchatov Institute'. Presented is the description of TOPRA-2 code intended for the engineering analysis of thermophysical and strength parameters of the WWER fuel rod - temperature distributions along the fuel radius, gas pressures under the cladding, stresses in the cladding, etc. for the reactor operation in normal conditions. Presented are some results of the code verification against test problems and the data obtained in the experimental programs. Presented are comparison results of the calculations with TOPRA-2 and TRANSURANUS (V1M1J06) codes. Results obtained in the course of verification demonstrate possibility of application of the methodology and TOPRA-2 code for the engineering analysis of the WWER fuel rods

CAFE: A Computer Tool for Accurate Simulation of the Regulatory Pool Fire Environment for Type B Packages

International Nuclear Information System (INIS)

Gritzo, L.A.; Koski, J.A.; Suo-Anttila, A.J.

1999-01-01

The Container Analysis Fire Environment computer code (CAFE) is intended to provide Type B package designers with an enhanced engulfing fire boundary condition when combined with the PATRAN/P-Thermal commercial code. Historically an engulfing fire boundary condition has been modeled as σT 4 where σ is the Stefan-Boltzman constant, and T is the fire temperature. The CAFE code includes the necessary chemistry, thermal radiation, and fluid mechanics to model an engulfing fire. Effects included are the local cooling of gases that form a protective boundary layer that reduces the incoming radiant heat flux to values lower than expected from a simple σT 4 model. In addition, the effect of object shape on mixing that may increase the local fire temperature is included. Both high and low temperature regions that depend upon the local availability of oxygen are also calculated. Thus the competing effects that can both increase and decrease the local values of radiant heat flux are included in a reamer that is not predictable a-priori. The CAFE package consists of a group of computer subroutines that can be linked to workstation-based thermal analysis codes in order to predict package performance during regulatory and other accident fire scenarios

The Fireball integrated code package

Energy Technology Data Exchange (ETDEWEB)

Dobranich, D.; Powers, D.A.; Harper, F.T.

1997-07-01

Many deep-space satellites contain a plutonium heat source. An explosion, during launch, of a rocket carrying such a satellite offers the potential for the release of some of the plutonium. The fireball following such an explosion exposes any released plutonium to a high-temperature chemically-reactive environment. Vaporization, condensation, and agglomeration processes can alter the distribution of plutonium-bearing particles. The Fireball code package simulates the integrated response of the physical and chemical processes occurring in a fireball and the effect these processes have on the plutonium-bearing particle distribution. This integrated treatment of multiple phenomena represents a significant improvement in the state of the art for fireball simulations. Preliminary simulations of launch-second scenarios indicate: (1) most plutonium vaporization occurs within the first second of the fireball; (2) large non-aerosol-sized particles contribute very little to plutonium vapor production; (3) vaporization and both homogeneous and heterogeneous condensation occur simultaneously; (4) homogeneous condensation transports plutonium down to the smallest-particle sizes; (5) heterogeneous condensation precludes homogeneous condensation if sufficient condensation sites are available; and (6) agglomeration produces larger-sized particles but slows rapidly as the fireball grows.

Intra-ELM phase modelling of a JET ITER-like wall H-mode discharge with EDGE2D-EIRENE

Energy Technology Data Exchange (ETDEWEB)

Harting, D.M., E-mail: Derek.Harting@ccfe.ac.uk [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Wiesen, S. [Institute of Energy and Climate Research – IEK4, Association EURATOM-FZJ, D-52425 Jülich (Germany); Groth, M. [Aalto University, Association EURATOM-Tekes, Espoo (Finland); Brezinsek, S. [Institute of Energy and Climate Research – IEK4, Association EURATOM-FZJ, D-52425 Jülich (Germany); Corrigan, G.; Arnoux, G. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Boerner, P. [Institute of Energy and Climate Research – IEK4, Association EURATOM-FZJ, D-52425 Jülich (Germany); Devaux, S.; Flanagan, J. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Järvinen, A. [Aalto University, Association EURATOM-Tekes, Espoo (Finland); Marsen, S. [Max-Planck-Institut für Plasmaphysik, EURATOM-Association, D-17491 Greifswald (Germany); Reiter, D. [Institute of Energy and Climate Research – IEK4, Association EURATOM-FZJ, D-52425 Jülich (Germany)

2015-08-15

We present the application of an improved EDGE2D-EIRENE SOL transport model for the ELM phase utilizing kinetic correction of the sheath-heat-transmission coefficients and heat-flux-limiting factors used in fluid SOL modelling. With a statistical analysis over a range of similar type-I ELMy H-mode discharges performed at the end of the first JET ITER-like wall campaign, we achieved a fast (Δt = 200 μs) temporal evolution of the outer midplane n{sub e} and T{sub e} profiles and the target-heat and particle-flux profiles, which provides a good experimental data set to understand the characteristics of an ELM cycle. We will demonstrate that these kinetic corrections increase the simulated heat-flux-rise time at the target to experimentally observed times but the power-decay time at the target is still underestimated by the simulations. This longer decay times are potentially related to a change of the local recycling coefficient at the tungsten target plate directly after the heat pulse.

The CNCSN: one, two- and three-dimensional coupled neutral and charged particle discrete ordinates code package

International Nuclear Information System (INIS)

Voloschenko, A.M.; Gukov, S.V.; Kryuchkov, V.P.; Dubinin, A.A.; Sumaneev, O.V.

2005-01-01

The CNCSN package is composed of the following codes: -) KATRIN-2.0: a three-dimensional neutral and charged particle transport code; -) KASKAD-S-2.5: a two-dimensional neutral and charged particle transport code; -) ROZ-6.6: a one-dimensional neutral and charged particle transport code; -) ARVES-2.5: a preprocessor for the working macroscopic cross-section format FMAC-M for transport calculations; -) MIXERM: a utility code for preparing mixtures on the base of multigroup cross-section libraries in ANISN format; -) CEPXS-BFP: a version of the Sandia National Lab. multigroup coupled electron-photon cross-section generating code CEPXS, adapted for solving the charged particles transport in the Boltzmann-Fokker-Planck formulation with the use of discrete ordinate method; -) SADCO-2.4: Institute for High-Energy Physics modular system for generating coupled nuclear data libraries to provide high-energy particles transport calculations by multigroup method; -) KATRIF: the post-processor for the KATRIN code; -) KASF: the post-processor for the KASKAD-S code; and ROZ6F: the post-processor for the ROZ-6 code. The coding language is Fortran-90

Qualification tests for a type B (U) package

International Nuclear Information System (INIS)

Vieru, G.

2004-01-01

The primary objective for the safety of radioactive materials transport is to protect human health and the environment taking into consideration its potential risks and radiological consequences. Romania as a Member State of the International Atomic Energy Agency has implemented national regulations for the safe transport of radioactive materials (RAM) in accordance with the Agency's recommendations as well as other international specialized organizations. The paper will describe the qualification tests performed for a type B (U) package, intended to be used for the transport of the radioactive sources Am-241 and Cs-137. For this kind of package the tests were performed the first time in Romania and include: the water spray test, the 1.2 m free drop test, the stacking test, the penetration test, the 9m free drop test, the thermal test and the submersion under a head of water of at least 15 m. The test facilities used for performing qualification tests for the type B (U) package as well as experience and conclusions will be also presented

NPTFit: A Code Package for Non-Poissonian Template Fitting

International Nuclear Information System (INIS)

Mishra-Sharma, Siddharth; Rodd, Nicholas L.; Safdi, Benjamin R.

2017-01-01

We present NPTFit, an open-source code package, written in Python and Cython, for performing non-Poissonian template fits (NPTFs). The NPTF is a recently developed statistical procedure for characterizing the contribution of unresolved point sources (PSs) to astrophysical data sets. The NPTF was first applied to Fermi gamma-ray data to provide evidence that the excess of ∼GeV gamma-rays observed in the inner regions of the Milky Way likely arises from a population of sub-threshold point sources, and the NPTF has since found additional applications studying sub-threshold extragalactic sources at high Galactic latitudes. The NPTF generalizes traditional astrophysical template fits to allow for the ability to search for populations of unresolved PSs that may follow a given spatial distribution. NPTFit builds upon the framework of the fluctuation analyses developed in X-ray astronomy, thus it likely has applications beyond those demonstrated with gamma-ray data. The NPTFit package utilizes novel computational methods to perform the NPTF efficiently. The code is available at http://github.com/bsafdi/NPTFit and up-to-date and extensive documentation may be found at http://nptfit.readthedocs.io.

NPTFit: A Code Package for Non-Poissonian Template Fitting

Energy Technology Data Exchange (ETDEWEB)

Mishra-Sharma, Siddharth [Department of Physics, Princeton University, Princeton, NJ 08544 (United States); Rodd, Nicholas L.; Safdi, Benjamin R., E-mail: smsharma@princeton.edu, E-mail: nrodd@mit.edu, E-mail: bsafdi@mit.edu [Center for Theoretical Physics, Massachusetts Institute of Technology, Cambridge, MA 02139 (United States)

2017-06-01

We present NPTFit, an open-source code package, written in Python and Cython, for performing non-Poissonian template fits (NPTFs). The NPTF is a recently developed statistical procedure for characterizing the contribution of unresolved point sources (PSs) to astrophysical data sets. The NPTF was first applied to Fermi gamma-ray data to provide evidence that the excess of ∼GeV gamma-rays observed in the inner regions of the Milky Way likely arises from a population of sub-threshold point sources, and the NPTF has since found additional applications studying sub-threshold extragalactic sources at high Galactic latitudes. The NPTF generalizes traditional astrophysical template fits to allow for the ability to search for populations of unresolved PSs that may follow a given spatial distribution. NPTFit builds upon the framework of the fluctuation analyses developed in X-ray astronomy, thus it likely has applications beyond those demonstrated with gamma-ray data. The NPTFit package utilizes novel computational methods to perform the NPTF efficiently. The code is available at http://github.com/bsafdi/NPTFit and up-to-date and extensive documentation may be found at http://nptfit.readthedocs.io.

Code package for calculation of damage effects of medium-energy protons in metal targets

International Nuclear Information System (INIS)

Coulter, C.A.

1976-12-01

A program package was developed to calculate radiation damage effects produced in a metal target by protons in the 100-MeV to 3.5-GeV energy range. A detailed description is given of the control cards and data cards required to use the code package

Draft ASME code case on ductile cast iron for transport packaging

International Nuclear Information System (INIS)

Saegusa, T.; Arai, T.; Hirose, M.; Kobayashi, T.; Tezuka, Y.; Urabe, N.; Hueggenberg, R.

2004-01-01

The current Rules for Construction of ''Containment Systems for Storage and Transport Packagings of Spent Nuclear Fuel and High Level Radioactive Material and Waste'' of Division 3 in Section III of ASME Code (2001 Edition) does not include ductile cast iron in its list of materials permitted for use. The Rules specify required fracture toughness values of ferritic steel material for nominal wall thickness 5/8 to 12 inches (16 to 305 mm). New rule for ductile cast iron for transport packaging of which wall thickness is greater than 12 inches (305mm) is required

Safety analysis report for packages: packaging of fissile and other radioactive materials. Final report

International Nuclear Information System (INIS)

Chalfant, G.G.

1984-01-01

The 9965, 9966, 9967, and 9968 packages are designed for surface shipment of fissile and other radioactive materials where a high degree of containment (either single or double) is required. Provisions are made to add shielding material to the packaging as required. The package was physically tested to demonstrate that it meets the criteria specified in USDOE Order No. 5480.1, chapter III, dated 5/1/81, which invokes Title 10, Code of Federal Regulations, Part 71 (10 CFR 71), Packing and Transportation of Radioactive Material, and Title 49, Code of Federal Regulations, Part 100-179, Transportation. By restricting the maximum normal operating pressure of the packages to less than 7 kg/cm 2 (gauge) (99 to 54 psig), the packages will comply with Type B(U) regulations of the International Atomic Energy Agency (IAEA) in its Regulations for the Safe Transport of Radioactive Materials, Safety Series No. 6, 1973 Revised Edition, and may be used for export and import shipments. These packages have been assessed for transport of up to 14.5 kilograms of uranium, excluding uranium-233, or 4.4 kilograms of plutonium metal, oxides, or scrap having a maximum radioactive decay energy of 30 watts. Specific maximum package contents are given. This quantity and the configuration of uranium or plutonium metal cannot be made critical by any combination of hydrogeneous reflection and moderation regardless of the condition of the package. For a uranium-233 shipment, a separate criticality evaluation for the specific package is required

Cleanup Verification Package for the 118-B-6, 108-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Proctor, M.L.

2006-01-01

This cleanup verification package documents completion of remedial action for the 118-B-6, 108-B Solid Waste Burial Ground. The 118-B-6 site consisted of 2 concrete pipes buried vertically in the ground and capped by a concrete pad with steel lids. The site was used for the disposal of wastes from the 'metal line' of the P-10 Tritium Separation Project.

Computer code ANISN multiplying media and shielding calculation 2. Code description (input/output)

International Nuclear Information System (INIS)

Maiorino, J.R.

1991-01-01

The new code CCC-0514-ANISN/PC is described, as well as a ''GENERAL DESCRIPTION OF ANISN/PC code''. In addition to the ANISN/PC code, the transmittal package includes an interactive input generation programme called APE (ANISN Processor and Evaluator), which facilitates the work of the user in giving input. Also, a 21 group photon cross section master library FLUNGP.LIB in ISOTX format, which can be edited by an executable file LMOD.EXE, is included in the package. The input and output subroutines are reviewed. 6 refs, 1 fig., 1 tab

Island divertor studies on W7-AS

International Nuclear Information System (INIS)

Sardei, F.; Feng, Y.; Grigull, P.; Herre, G.; Hildebrandt, D.; Hofmann, J.V.; Kisslinger, J.; Brakel, R.; Das, J.; Geiger, J.; Heinrich, O.; Kuehner, G.; Niedermeyer, H.; Reiter, D.; Richter-Gloetzl, M.; Runov, A.; Schneider, R.; Stroth, U.; Verbeek, H.; Wagner, F.; Wolf, R.

1997-01-01

Basic topological features of the island divertor concept for low shear stellarators are discussed with emphasis on the differences to tokamak divertors. Extensive measurements of the edge structures by two-dimensional plasma spectroscopy and by target calorimetry are in excellent agreement with predicted vacuum and equilibrium configurations, which are available up to central β values of ∝1%. For this β value the calculated field-line pitch inside the islands is twice that of the corresponding vacuum case. Video observations of the strike points indicate stability of the island structures for central β values up to ∝3.7%. The interpretation of the complex island divertor physics of W7-AS has become possible by the development of the three-dimensional plasma transport code EMC3 (Edge Monte Carlo 3D), which has been coupled self-consistently to the EIRENE neutral gas code. Analysis of high density NBI discharges gives strong indications of stable high recycling conditions for n e ≥10 20 m -3 . The observations are reproduced by the EMC3/EIRENE code and supported by calculations with the B2/EIRENE code adapted to W7-AS. Improvement of recycling, pumping and target load distribution is expected from the new optimized target plates and baffles to be installed in W7-AS. (orig.)

Simulation of neutral gas flow in a tokamak divertor using the Direct Simulation Monte Carlo method

International Nuclear Information System (INIS)

Gleason-González, Cristian; Varoutis, Stylianos; Hauer, Volker; Day, Christian

2014-01-01

Highlights: • Subdivertor gas flows calculations in tokamaks by coupling the B2-EIRENE and DSMC method. • The results include pressure, temperature, bulk velocity and particle fluxes in the subdivertor. • Gas recirculation effect towards the plasma chamber through the vertical targets is found. • Comparison between DSMC and the ITERVAC code reveals a very good agreement. - Abstract: This paper presents a new innovative scientific and engineering approach for describing sub-divertor gas flows of fusion devices by coupling the B2-EIRENE (SOLPS) code and the Direct Simulation Monte Carlo (DSMC) method. The present study exemplifies this with a computational investigation of neutral gas flow in the ITER's sub-divertor region. The numerical results include the flow fields and contours of the overall quantities of practical interest such as the pressure, the temperature and the bulk velocity assuming helium as model gas. Moreover, the study unravels the gas recirculation effect located behind the vertical targets, viz. neutral particles flowing towards the plasma chamber. Comparison between calculations performed by the DSMC method and the ITERVAC code reveals a very good agreement along the main sub-divertor ducts

Validation of the DRAGON/DONJON code package for MNR using the IAEA 10 MW benchmark problem

International Nuclear Information System (INIS)

Day, S.E.; Garland, W.J.

2000-01-01

The first step in developing a framework for reactor physics analysis is to establish the appropriate and proven reactor physics codes. The chosen code package is tested, by executing a benchmark problem and comparing the results to the accepted standards. The IAEA 10 MW Benchmark problem is suitable for static reactor physics calculations on plate-fueled research reactor systems and has been used previously to validate codes for the McMaster Nuclear (MNR). The flexible and advanced geometry capabilities of the DRAGON transport theory code make it a desirable tool, and the accompanying DONJON diffusion theory code also has useful features applicable to safety analysis work at MNR. This paper describes the methodology used to benchmark the DRAGON/DONJON code package against this problem and the results herein extend the domain of validation of this code package. The results are directly applicable to MNR and are relevant to a reduced-enrichment fuel program. The DRAGON transport code models, used in this study, are based on the 1-D infinite slab approximation whereas the DONJON diffusion code models are defined in 3-D Cartesian geometry. The cores under consideration are composed of HEU (93% enrichment), MEU (45% enrichment) and LEU (20% enrichment) fuel and are examined in a fresh state, as well as at beginning-of-life (BOL) and end-of-life (EOL) exposures. The required flux plots and flux-ratio plots are included, as are transport theory code k∞and diffusion theory code k eff results. In addition to this, selected isotope atom densities are charted as a function of fuel burnup. Results from this analysis are compared to and are in good agreement with previously published results. (author)

Department of Transportation -- Exemption for using the Transuranic Package Transporter-I (TRUPACT-I) at the Idaho National Engineering Laboratory (Code of Federal Regulations, Title 49, Part 107, Subpart B -- Exemptions, 107-103 Application for Exemption)

International Nuclear Information System (INIS)

Tyacke, M.J.; Macdonald, R.J.

1992-08-01

Exemption from specific regulations is being sought for the Transuranic Package Transporter Model I (TRUPACT-I) container. The design has successfully undergone extensive testing of a quarter-scale model and a full-scale prototype of the container. Results from the analysis and testing are in the TRUPACT-1 Safely Analysis Report for Packaging (SARP), GA-Al8695/SAND 87-7104 (TTC0735), April 1987 (see Attachment 1). The container was never certified or used because of questions raised during the certification process. Two features of the container design failed to satisfy the regulations for Type B packaging. First, the design utilizes a venting system to control internal and external pressures; this venting system is not allowed by the Code of Federal Regulations, Title 10, Parts 71(h) and 71.51(b) [10 CFR 71.(h) and 71.51(b)]. Second, the maximum quantity fissile material proposed to be hauled in TRUPACT-I exceeded the limits in 10 CFR 71.63(b) for a single-containment container. To correct these design deficiencies, the vents would be plugged during transport, and the maximum quantity of fissile material would be limited to the allowables for a single-containment container. An engineering analysis showed that the container could safely transport radioactive material within the boundaries of the Idaho National Engineering Laboratory (INEL) with the vent system plugged (see Attachment 2). However, some of the requirements for determining pressure on a container need to be changed (i.e., exempted) to reflect conditions unique to the INEL. The following are the requirements needing to be changed for INEL conditions, variances being sought, and justifications for the variances

Safety evaluation for packaging 222-S laboratory cargo tank for onetime type B material shipment

International Nuclear Information System (INIS)

Nguyen, P.M.

1994-01-01

The purpose of this Safety Evaluation for Packaging (SEP) is to evaluate and document the safety of the onetime shipment of bulk radioactive liquids in the 222-S Laboratory cargo tank (222-S cargo tank). The 222-S cargo tank is a US Department of Transportation (DOT) MC-312 specification (DOT 1989) cargo tank, vehicle registration number HO-64-04275, approved for low specific activity (LSA) shipments in accordance with the DOT Title 49, Code of Federal Regulations (CFR). In accordance with the US Department of Energy, Richland Operations Office (RL) Order 5480.1A, Chapter III (RL 1988), an equivalent degree of safety shall be provided for onsite shipments as would be afforded by the DOT shipping regulations for a radioactive material package. This document demonstrates that this packaging system meets the onsite transportation safety criteria for a onetime shipment of Type B contents

Verification of LOCA/ECCS analysis codes ALARM-B2 and THYDE-B1 by comparison with RELAP4/MOD6/U4/J3

International Nuclear Information System (INIS)

Shimizu, Takashi

1982-08-01

For a verification study of ALARM-B2 code and THYDE-B1 code which are the component of the JAERI code system for evaluation of BWR ECCS performance, calculations for typical small and large break LOCA in BWR were done, and compared with those by RELAP4/MOD6/U4/J3 code. This report describes the influences of differences between the analytical models incorporated in the individual code and the problems identified by this verification study. (author)

Verification test calculations for the Source Term Code Package

International Nuclear Information System (INIS)

Denning, R.S.; Wooton, R.O.; Alexander, C.A.; Curtis, L.A.; Cybulskis, P.; Gieseke, J.A.; Jordan, H.; Lee, K.W.; Nicolosi, S.L.

1986-07-01

The purpose of this report is to demonstrate the reasonableness of the Source Term Code Package (STCP) results. Hand calculations have been performed spanning a wide variety of phenomena within the context of a single accident sequence, a loss of all ac power with late containment failure, in the Peach Bottom (BWR) plant, and compared with STCP results. The report identifies some of the limitations of the hand calculation effort. The processes involved in a core meltdown accident are complex and coupled. Hand calculations by their nature must deal with gross simplifications of these processes. Their greatest strength is as an indicator that a computer code contains an error, for example that it doesn't satisfy basic conservation laws, rather than in showing the analysis accurately represents reality. Hand calculations are an important element of verification but they do not satisfy the need for code validation. The code validation program for the STCP is a separate effort. In general the hand calculation results show that models used in the STCP codes (e.g., MARCH, TRAP-MELT, VANESA) obey basic conservation laws and produce reasonable results. The degree of agreement and significance of the comparisons differ among the models evaluated. 20 figs., 26 tabs

Divertor modelling for conceptual studies of tokamak fusion reactor FDS-III

International Nuclear Information System (INIS)

Chen Yiping; Liu Songlin

2010-01-01

Divertor modelling for the conceptual studies of tokamak fusion reactor FDS-III was carried out by using the edge plasma code package B2.5-Eirene (SOLPS5.0). The modelling was performed by taking real MHD equilibrium and divertor geometry of the reactor into account. The profiles of plasma temperature, density and heat fluxes in the computational region and at the target plates have been obtained. The modelling results show that, with the fusion power P fu =2.6 GW and the edge density N edge =6.0x10 19 l/m 3 , the peak values of electron and ion heat fluxes at the outer target plate of divertor are respectively 93.92 MW/m 2 and 58.50 MW/m 2 . According to the modelling results it is suggested that some methods for reducing the heat fluxes at the target plates should be used in order to get acceptable level of power flux at the target plates for the divertor design of the reactor.

Characterization of open-cycle coal-fired MHD generators. Quarterly technical summary report No. 6, October 1--December 31, 1977. [PACKAGE code

Energy Technology Data Exchange (ETDEWEB)

Kolb, C.E.; Yousefian, V.; Wormhoudt, J.; Haimes, R.; Martinez-Sanchez, M.; Kerrebrock, J.L.

1978-01-30

Research has included theoretical modeling of important plasma chemical effects such as: conductivity reductions due to condensed slag/electron interactions; conductivity and generator efficiency reductions due to the formation of slag-related negative ion species; and the loss of alkali seed due to chemical combination with condensed slag. A summary of the major conclusions in each of these areas is presented. A major output of the modeling effort has been the development of an MHD plasma chemistry core flow model. This model has been formulated into a computer program designated the PACKAGE code (Plasma Analysis, Chemical Kinetics, And Generator Efficiency). The PACKAGE code is designed to calculate the effect of coal rank, ash percentage, ash composition, air preheat temperatures, equivalence ratio, and various generator channel parameters on the overall efficiency of open-cycle, coal-fired MHD generators. A complete description of the PACKAGE code and a preliminary version of the PACKAGE user's manual are included. A laboratory measurements program involving direct, mass spectrometric sampling of the positive and negative ions formed in a one atmosphere coal combustion plasma was also completed during the contract's initial phase. The relative ion concentrations formed in a plasma due to the methane augmented combustion of pulverized Montana Rosebud coal with potassium carbonate seed and preheated air are summarized. Positive ions measured include K/sup +/, KO/sup +/, Na/sup +/, Rb/sup +/, Cs/sup +/, and CsO/sup +/, while negative ions identified include PO/sub 3//sup -/, PO/sub 2//sup -/, BO/sub 2//sup -/, OH/sup -/, SH/sup -/, and probably HCrO/sub 3/, HMoO/sub 4//sup -/, and HWO/sub 3//sup -/. Comparison of the measurements with PACKAGE code predictions are presented. Preliminary design considerations for a mass spectrometric sampling probe capable of characterizing coal combustion plasmas from full scale combustors and flow trains are presented

Use of source term code package in the ELEBRA MX-850 system

International Nuclear Information System (INIS)

Guimaraes, A.C.F.; Goes, A.G.A.

1988-12-01

The implantation of source term code package in the ELEBRA-MX850 system is presented. The source term is formed when radioactive materials generated in nuclear fuel leakage toward containment and the external environment to reactor containment. The implantated version in the ELEBRA system are composed of five codes: MARCH 3, TRAPMELT 3, THCCA, VANESA and NAVA. The original example case was used. The example consists of a small loca accident in a PWR type reactor. A sensitivity study for the TRAPMELT 3 code was carried out, modifying the 'TIME STEP' to estimate the processing time of CPU for executing the original example case. (M.C.K.) [pt

Abstracts of digital computer code packages assembled by the Radiation Shielding Information Center

International Nuclear Information System (INIS)

Carter, B.J.; Maskewitz, B.F.

1985-04-01

This publication, ORNL/RSIC-13, Volumes I to III Revised, has resulted from an internal audit of the first 168 packages of computing technology in the Computer Codes Collection (CCC) of the Radiation Shielding Information Center (RSIC). It replaces the earlier three documents published as single volumes between 1966 to 1972. A significant number of the early code packages were considered to be obsolete and were removed from the collection in the audit process and the CCC numbers were not reassigned. Others not currently being used by the nuclear R and D community were retained in the collection to preserve technology not replaced by newer methods, or were considered of potential value for reference purposes. Much of the early technology, however, has improved through developer/RSIC/user interaction and continues at the forefront of the advancing state-of-the-art

Abstracts of digital computer code packages assembled by the Radiation Shielding Information Center

Energy Technology Data Exchange (ETDEWEB)

Carter, B.J.; Maskewitz, B.F.

1985-04-01

This publication, ORNL/RSIC-13, Volumes I to III Revised, has resulted from an internal audit of the first 168 packages of computing technology in the Computer Codes Collection (CCC) of the Radiation Shielding Information Center (RSIC). It replaces the earlier three documents published as single volumes between 1966 to 1972. A significant number of the early code packages were considered to be obsolete and were removed from the collection in the audit process and the CCC numbers were not reassigned. Others not currently being used by the nuclear R and D community were retained in the collection to preserve technology not replaced by newer methods, or were considered of potential value for reference purposes. Much of the early technology, however, has improved through developer/RSIC/user interaction and continues at the forefront of the advancing state-of-the-art.

International Code Assessment and Applications Program: Summary of code assessment studies concerning RELAP5/MOD2, RELAP5/MOD3, and TRAC-B

International Nuclear Information System (INIS)

Schultz, R.R.

1993-12-01

Members of the International Code Assessment Program (ICAP) have assessed the US Nuclear Regulatory Commission (USNRC) advanced thermal-hydraulic codes over the past few years in a concerted effort to identify deficiencies, to define user guidelines, and to determine the state of each code. The results of sixty-two code assessment reviews, conducted at INEL, are summarized. Code deficiencies are discussed and user recommended nodalizations investigated during the course of conducting the assessment studies and reviews are listed. All the work that is summarized was done using the RELAP5/MOD2, RELAP5/MOD3, and TRAC-B codes

Benchmark of the CASMO-3G/MICROBURN-B codes for Commonwealth Edison boiling water reactors

International Nuclear Information System (INIS)

Wheeler, J.K.; Pallotta, A.S.

1992-01-01

The Commonwealth Edison Company has performed an extensive benchmark against measured data from three boiling water reactors using the Studsvik lattice physics code CASMO-3G and the Siemens Nuclear Power three-dimensional simulator code MICROBURN-B. The measured data of interest for this benchmark are the hot and cold reactivity, and the core power distributions as measured by the traversing incore probe system and gamma scan data for fuel pins and assemblies. A total of nineteen unit-cycles were evaluated. The database included fuel product lines manufactured by General Electric and Siemens Nuclear Power, wit assemblies containing 7 x 7 to 9 x 9 pin configurations, several water rod designs, various enrichments and gadolina loadings, and axially varying lattice designs throughout the enriched portion of the bundle. The results of the benchmark present evidence that the CASMO-3G/MICROBURN-B code package can adequately model the range of fuel and core types in the benchmark, and the codes are acceptable for performing neutronic analyses of Commonwealth Edison's boiling water reactors

Microstructure and property measurements on in situ TiB2/70Si–Al composite for electronic packaging applications

International Nuclear Information System (INIS)

Zhang, L.; Gan, G.S.; Yang, B.

2012-01-01

Highlights: ► 2.0 wt.%TiB 2 /70Si–Al composite is prepared by a novel reactive technique. ► In situ TiB 2 particles can refine effectively the primary Si phase. ► The composite exhibited attractive physical and mechanical properties. -- Abstract: A novel reactive technique has been employed in fabrication of 2.0 wt.%TiB 2 /70Si–Al composite for electronic packaging applications. The microstructure and properties of composite were studied using scanning electron microscopy, energy dispersive X-ray spectrometer, coefficient of thermal expansion and thermal conductivity measurements, and 3-point bending tests. The results indicate that the in situ TiB 2 particles can effectively refine the primary Si phase. The property measurements results indicate that the 2.0 wt.%TiB 2 /70Si–Al composite has advantageous physical and mechanical properties, including low density, low coefficient of thermal expansion, high thermal conductivity, high Flexural strength and Brinell hardness.

Spent fuel packaging and its safety analysis

International Nuclear Information System (INIS)

Takada, Kimitaka; Nakaoki, Kozo; Tamamura, Tadao; Matsuda, Fumio; Fukudome, Kazuyuki

1983-01-01

An all stainless steel B(U) type packaging is proposed to transport spent fuels discharged from research reactors and other radioactive materials. The package is used dry and provided with surface fins to absorb drop shock and to dissipate decay heat. Safety was analyzed for structural, thermal, containment shielding and criticality factors, and the integrity of the package was confirmed with the MARC-CDC, TRUMP, ORIGEN, QAD, ANISN, and KENO computer codes. (author)

An analysis of options available for developing a common laser ray tracing package for Ares and Kull code frameworks

Energy Technology Data Exchange (ETDEWEB)

Weeratunga, S K

2008-11-06

Ares and Kull are mature code frameworks that support ALE hydrodynamics for a variety of HEDP applications at LLNL, using two widely different meshing approaches. While Ares is based on a 2-D/3-D block-structured mesh data base, Kull is designed to support unstructured, arbitrary polygonal/polyhedral meshes. In addition, both frameworks are capable of running applications on large, distributed-memory parallel machines. Currently, both these frameworks separately support assorted collections of physics packages related to HEDP, including one for the energy deposition by laser/ion-beam ray tracing. This study analyzes the options available for developing a common laser/ion-beam ray tracing package that can be easily shared between these two code frameworks and concludes with a set of recommendations for its development.

RELAP5/MOD2 code assessment

International Nuclear Information System (INIS)

Nithianandan, C.K.; Shah, N.H.; Schomaker, R.J.; Miller, F.R.

1985-01-01

Babcock and Wilcox (B and W) has been working with the code developers at EG and G and the US Nuclear Regulatory Commission in assessing the RELAP5/MOD2 computer code for the past year by simulating selected separate-effects tests. The purpose of this assessment has been to evaluate the code for use in MIST (Ref. 2) and OTIS integral system tests simulations and in the prediction of pressurized water reactor transients. B and W evaluated various versions of the code and made recommendations to improve code performance. As a result, the currently released version (cycle 36.1) has been improved considerably over earlier versions. However, further refinements to some of the constitutive models may still be needed to further improve the predictive capability of RELAP5/MOD2. The following versions of the code were evaluated. (1) RELAP/MOD2/Cycle 22 - first released version; (2) YELAP5/Cycle 32 - EG and G test version of RELAP5/MOD2/Cycle 32; (3) RELAP5/MOD2/Cycle 36 - frozen cycle for international code assessment; (4) updates to cycle 36 based on recommendations developed by B and W during the simulation of a Massachusetts Institute of Technology (MIT) pressurizer test; and (5) cycle 36.1 updates received from EG and G

RELAP5/MOD2 code assessment

Energy Technology Data Exchange (ETDEWEB)

Nithianandan, C.K.; Shah, N.H.; Schomaker, R.J.; Miller, F.R.

1985-11-01

Babcock and Wilcox (B and W) has been working with the code developers at EG and G and the US Nuclear Regulatory Commission in assessing the RELAP5/MOD2 computer code for the past year by simulating selected separate-effects tests. The purpose of this assessment has been to evaluate the code for use in MIST (Ref. 2) and OTIS integral system tests simulations and in the prediction of pressurized water reactor transients. B and W evaluated various versions of the code and made recommendations to improve code performance. As a result, the currently released version (cycle 36.1) has been improved considerably over earlier versions. However, further refinements to some of the constitutive models may still be needed to further improve the predictive capability of RELAP5/MOD2. The following versions of the code were evaluated. (1) RELAP/MOD2/Cycle 22 - first released version; (2) YELAP5/Cycle 32 - EG and G test version of RELAP5/MOD2/Cycle 32; (3) RELAP5/MOD2/Cycle 36 - frozen cycle for international code assessment; (4) updates to cycle 36 based on recommendations developed by B and W during the simulation of a Massachusetts Institute of Technology (MIT) pressurizer test; and (5) cycle 36.1 updates received from EG and G.

Running the source term code package in Elebra MX-850

International Nuclear Information System (INIS)

Guimaraes, A.C.F.; Goes, A.G.A.

1988-01-01

The source term package (STCP) is one of the main tools applied in calculations of behavior of fission products from nuclear power plants. It is a set of computer codes to assist the calculations of the radioactive materials leaving from the metallic containment of power reactors to the environment during a severe reactor accident. The original version of STCP runs in SDC computer systems, but as it has been written in FORTRAN 77, is possible run it in others systems such as IBM, Burroughs, Elebra, etc. The Elebra MX-8500 version of STCP contains 5 codes:March 3, Trapmelt, Tcca, Vanessa and Nava. The example presented in this report has taken into consideration a small LOCA accident into a PWR type reactor. (M.I.)

Experience with Wolsong-1 Phase-B pre-simulations using WIMS/DRAGON/RFSP-IST code suite

International Nuclear Information System (INIS)

Chung, D-H.; Kim, B-G.; Kim, S-M.; Suh, H-B.; Kim, H-S.; Kim, H-J.

2010-01-01

The Wolsong-1 Phase-B pre-simulations have been carried out with the exclusive use of the code suite WIMS/DRAGON/RFSP-IST in replacement of the previous PPV/MULTICELL/RFSP code system in preparation of tests to be conducted as scheduled in December 2010 after the refurbishment. A comprehensive simulation package has been undertaken starting from the approach to first criticality to the flux measurements and scan. In order to secure the validity of the results, the simulations are performed using both the Uniform and SCM fuel tables. An elaborating contribution has been invested into the work in view of the inexperience of using WIMS/SCM fuel tables as well as incremental cross sections generated by using DRAGON-IST. The overall assessment of simulation results indicates that the newly adopted WIMS/DRAGON/RFSP-IST code suite could be used in replacement of PPV/MULTICELL/RFSP for the verification against the Phase-B test results. (author)

Evaluation of finite element codes for demonstrating the performance of radioactive material packages in hypothetical accident drop scenarios

International Nuclear Information System (INIS)

Tso, C.F.; Hueggenberg, R.

2004-01-01

Drop testing and analysis are the two methods for demonstrating the performance of packages in hypothetical drop accident scenarios. The exact purpose of the tests and the analyses, and the relative prominence of the two in the license application, may depend on the Competent Authority and will vary between countries. The Finite Element Method (FEM) is a powerful analysis tool. A reliable finite element (FE) code when used correctly and appropriately, will allow a package's behaviour to be simulated reliably. With improvements in computing power, and in sophistication and reliability of FE codes, it is likely that FEM calculations will increasingly be used as evidence of drop test performance when seeking Competent Authority approval. What is lacking at the moment, however, is a standardised method of assessing a FE code in order to determine whether it is sufficiently reliable or pessimistic. To this end, the project Evaluation of Codes for Analysing the Drop Test Performance of Radioactive Material Transport Containers, funded by the European Commission Directorate-General XVII (now Directorate-General for Energy and Transport) and jointly performed by Arup and Gesellschaft fuer Nuklear-Behaelter mbH, was carried out in 1998. The work consisted of three components: Survey of existing finite element software, with a view to finding codes that may be capable of analysing drop test performance of radioactive material packages, and to produce an inventory of them. Develop a set of benchmark problems to evaluate software used for analysing the drop test performance of packages. Evaluate the finite element codes by testing them against the benchmarks This paper presents a summary of this work

Evaluation of finite element codes for demonstrating the performance of radioactive material packages in hypothetical accident drop scenarios

Energy Technology Data Exchange (ETDEWEB)

Tso, C.F. [Arup (United Kingdom); Hueggenberg, R. [Gesellschaft fuer Nuklear-Behaelter mbH (Germany)

2004-07-01

Drop testing and analysis are the two methods for demonstrating the performance of packages in hypothetical drop accident scenarios. The exact purpose of the tests and the analyses, and the relative prominence of the two in the license application, may depend on the Competent Authority and will vary between countries. The Finite Element Method (FEM) is a powerful analysis tool. A reliable finite element (FE) code when used correctly and appropriately, will allow a package's behaviour to be simulated reliably. With improvements in computing power, and in sophistication and reliability of FE codes, it is likely that FEM calculations will increasingly be used as evidence of drop test performance when seeking Competent Authority approval. What is lacking at the moment, however, is a standardised method of assessing a FE code in order to determine whether it is sufficiently reliable or pessimistic. To this end, the project Evaluation of Codes for Analysing the Drop Test Performance of Radioactive Material Transport Containers, funded by the European Commission Directorate-General XVII (now Directorate-General for Energy and Transport) and jointly performed by Arup and Gesellschaft fuer Nuklear-Behaelter mbH, was carried out in 1998. The work consisted of three components: Survey of existing finite element software, with a view to finding codes that may be capable of analysing drop test performance of radioactive material packages, and to produce an inventory of them. Develop a set of benchmark problems to evaluate software used for analysing the drop test performance of packages. Evaluate the finite element codes by testing them against the benchmarks This paper presents a summary of this work.

Analysis of the main steam line break accident with loss of offsite power using the fully coupled RELAP5/PANTHER/COBRA code package

International Nuclear Information System (INIS)

Ruben Van Parys; Sandrine Bosso; Christophe Schneidesch; Jinzhao Zhang

2005-01-01

Full text of publication follows: A coupled thermal hydraulics-neutronics code package (RELAP5/PANTHER/COBRA) has been qualified for accident analysis at Tractebel Engineering. In the TE coupled code package, the best estimate thermal-hydraulic system code, RELAP5/MOD2.5, is coupled with the full three-dimensional reactor core kinetics code, PANTHER, via a dynamic data exchange control and processing tool, TALINK. An interface between PANTHER code and the sub-channel thermal-hydraulic analysis code COBRA-IIIC is developed in order to perform online calculation of Departure from Nucleate Boiling Ratio (DNBR). The TE coupled code package has been applied to develop a MSLB accident analysis methodology using the TE deterministic bounding approach. The methodology has been applied for MSLB accident analysis in support of licensing of the power up-rate and steam generator replacement of the Doel 2 plant. The results of coupled thermal-hydraulic and neutronic analysis of SLB show that there exists an important margin in the traditional FSAR MSLB accident analysis. As a specific licensing requirement, the main steam line break accident with loss of offsite power has to be analyzed. In the standard methodology with the coupled RELAP5/PANTHER code, and some corrective methods has to be taken in order to overcome the limitations due to the close-channel T/H model in PANTHER at low flow conditions. The results show that the steam line break accident with loss of offsite power is far less limiting. In order to verify the effect of the cross-flow at low flow conditions, the fully dynamic coupling of RELAP5/PANTHER/COBRA code package is used for reanalysis of this case, in which the PANTHER close-channel T/H model is replaced by the COBRA sub-channel T/H model with crossflow option. It has been demonstrated that, although the consideration of cross-flow in this challenging situation may lead to higher core return to power and slightly lower DNBR than in the standard methodology

Analysis of the main steam line break accident with loss of offsite power using the fully coupled RELAP5/PANTHER/COBRA code package

Energy Technology Data Exchange (ETDEWEB)

Ruben Van Parys; Sandrine Bosso; Christophe Schneidesch; Jinzhao Zhang [Nuclear Department, Suez-Tractebel Engineering, avenue Ariane 5, B-1200 Brussels (Belgium)

2005-07-01

Full text of publication follows: A coupled thermal hydraulics-neutronics code package (RELAP5/PANTHER/COBRA) has been qualified for accident analysis at Tractebel Engineering. In the TE coupled code package, the best estimate thermal-hydraulic system code, RELAP5/MOD2.5, is coupled with the full three-dimensional reactor core kinetics code, PANTHER, via a dynamic data exchange control and processing tool, TALINK. An interface between PANTHER code and the sub-channel thermal-hydraulic analysis code COBRA-IIIC is developed in order to perform online calculation of Departure from Nucleate Boiling Ratio (DNBR). The TE coupled code package has been applied to develop a MSLB accident analysis methodology using the TE deterministic bounding approach. The methodology has been applied for MSLB accident analysis in support of licensing of the power up-rate and steam generator replacement of the Doel 2 plant. The results of coupled thermal-hydraulic and neutronic analysis of SLB show that there exists an important margin in the traditional FSAR MSLB accident analysis. As a specific licensing requirement, the main steam line break accident with loss of offsite power has to be analyzed. In the standard methodology with the coupled RELAP5/PANTHER code, and some corrective methods has to be taken in order to overcome the limitations due to the close-channel T/H model in PANTHER at low flow conditions. The results show that the steam line break accident with loss of offsite power is far less limiting. In order to verify the effect of the cross-flow at low flow conditions, the fully dynamic coupling of RELAP5/PANTHER/COBRA code package is used for reanalysis of this case, in which the PANTHER close-channel T/H model is replaced by the COBRA sub-channel T/H model with crossflow option. It has been demonstrated that, although the consideration of cross-flow in this challenging situation may lead to higher core return to power and slightly lower DNBR than in the standard methodology

COOLOD-N2: a computer code, for the analyses of steady-state thermal-hydraulics in research reactors

International Nuclear Information System (INIS)

Kaminaga, Masanori

1994-03-01

The COOLOD-N2 code provides a capability for the analyses of the steady-state thermal-hydraulics of research reactors. This code is revised version of the COOLOD-N code, and is applicable not only for research reactors in which plate-type fuel is adopted, but also for research reactors in which rod-type fuel is adopted. In the code, subroutines to calculate temperature distribution in rod-type fuel have been newly added to the COOLOD-N code. The COOLOD-N2 code can calculate fuel temperatures under both forced convection cooling mode and natural convection cooling mode as well as COOLOD-N code. In the COOLOD-N2 code, a 'Heat Transfer package' is used for calculating heat transfer coefficient, DNB heat flux etc. The 'Heat Transfer package' is subroutine program and is especially developed for research reactors in which plate-type fuel is adopted. In case of rod-type fuel, DNB heat flux is calculated by both the 'Heat Transfer package' and Lund DNB heat flux correlation which is popular for TRIGA reactor. The COOLOD-N2 code also has a capability of calculating ONB temperature, the heat flux at onset of flow instability as well as DNB heat flux. (author)

Containers analysis code of zero order (CACO0) - A basic design system for Type B packages

International Nuclear Information System (INIS)

Gaspar, C.; Benito, G.; Rey, J.C.

1989-01-01

Very frequently, the principal issues that have to be assessed in the design of a type B(U) package are radiation shielding and evaluation of mechanical and thermal test effects. Thermal behavior during normal transport conditions has also to be considered when the material must dissipate high thermal power. If the transported material is fissile it should be assured that it remains subcritical during transport. The containment of radioactive material must always be assured. In some cases this requires considerable effort. Usually these different design issues are very closely coupled. This coupling does not permit independent consideration. Also, some issues are competitive and generate conflicting design criteria. Given the goal of meeting pertinent transport regulations at a reasonable cost, all design-relevant issues must be balanced in order to obtain a good design. For each design-relevant issue there exists a number of methods of varying efficiency and cost, which can be used to define the key parameters of those particular issues. The overall design methodology must taken into account interactions between parameters of different issues. CACO0 is a system that integrates all design relevant issues and their interactions. The system consists of different modules, each one oriented to a different design issue. The modules are related by a control structure that enables sequentation or iteration during design in a fast and simple manner. Modules can easily be replaced or added, so the system can be updated or adapted to new design problems. The system was designed for use in factibility analysis, cost estimation, conceptual design and initial stages of basic design of type B(U) packages. To accomplish those ends, simple, fast and conservative methods are used

CH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2008-01-16

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Implantation, evaluation and improvement of the diffusion code package developed by the RIS0 Research Center

International Nuclear Information System (INIS)

Koide, M.C.M.

1983-01-01

The evaluation and improvement of the diffusion code package developed by the RIS0 Research Center of Denmark have been performed. The improvements made in the package consisted in the presentation of their manuals. In order to reduce the process time of the codes an analitical boundary condition capable of representing the effects of the baffle and the reflector on the flux distribution has been calculated. Such boundary condition was obtained using a one-dimensional medium in the framework of the two group diffusion theory. The results showed that the application of this boundary condition produces very accurate results and an appreciable economy of processing time. (author) [pt

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2008-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package (also known as the 'RH-TRU 72-B cask') and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous

MORET: Version 4.B. A multigroup Monte Carlo criticality code

International Nuclear Information System (INIS)

Jacquet, Olivier; Miss, Joachim; Courtois, Gerard

2003-01-01

MORET 4 is a three dimensional multigroup Monte Carlo code which calculates the effective multiplication factor (keff) of any configurations more or less complex as well as reaction rates in the different volumes of the geometry and the leakage out of the system. MORET 4 is the Monte Carlo code of the APOLLO2-MORET 4 standard route of CRISTAL, the French criticality package. It is the most commonly used Monte Carlo code for French criticality calculations. During the last four years, the MORET 4 team has developed or improved the following major points: modernization of the geometry, implementation of perturbation algorithms, source distribution convergence, statistical detection of stationarity, unbiased variance estimation and creation of pre-processing and post-processing tools. The purpose of this paper is not only to present the new features of MORET but also to detail clearly the physical models and the mathematical methods used in the code. (author)

Experimental study on highly collisional edge plasmas in W7-AS island divertor configurations

International Nuclear Information System (INIS)

Grigull, P.; Hildebrandt, D.; Sardei, F.; Feng, Y.; Herre, G.; Herrmann, A.; Hofmann, J.V.; Kisslinger, J.; Kuehner, G.; Niedermeyer, H.; Schneider, R.; Verbeek, H.; Wagner, F.; Wolf, R.; Zhang, X.D.

1997-01-01

Edge plasma scenarios in island divertor configurations ('natural' magnetic islands intersected by targets) are studied by comparing data from moderate to high density NBI discharges with 3D code (EMC3/EIRENE) results. The data strongly indicate that high recycling with significant particle flux enhancement was achieved in this geometry. But, plasma pressure losses towards the targets are relatively strong, and high recycling sets in only at n e >10 20 m -3 . The respective density enhancement in front of the targets is moderate (up to a factor of about three relative to the upstream density). These scenarios are also in basic agreement with B2/EIRENE code predictions. At n e >1.5 x 10 20 m -3 detachment seems to develop. Improvements are expected from additional coils controlling the field line pitch inside the islands, and from optimized targets which will better focus recycling neutrals into the islands. Both are in preparation. (orig.)

Provision of transport packaging for radioactive materials

International Nuclear Information System (INIS)

1981-04-01

The safe transport of radioactive materials is governed by various regulations based on International Atomic Energy Agency Regulations. This code of practice is a supplement to the regulations, its objects being (a) to advise designers of packaging on the technical features necessary to conform to the regulations, and (b) to outline the requirements for obtaining approval of package designs from the competent authority. (U.K.)

How to avoid errors in the design and fabrication of transportation packages

International Nuclear Information System (INIS)

Raske, D.T.

1996-01-01

The purpose of this paper is to discuss the errors and omissions most often identified when reviewing the design and fabrication of a packaging to transport high-level radioactive materials. The design and fabrication criteria recommended by the U.S. Department of Energy, Office of Facility Safety Analysis, for containment vessels of Type B commercial packagings containing high-level radioactive materials is based on the requirements of Section III, Division 1, Subsection NB of the ASME Boiler and Pressure Vessel Code. However, most packaging designers, engineers, and fabricators are intimidated by the sheer volume of requirements contained in the Code; as a result, the Code is not always followed and many requirements that do apply are often overlooked during preparation of the Safety Analysis Report for Packaging that constitutes the basis for evaluating the packaging for certification

Benchmark calculation for GT-MHR using HELIOS/MASTER code package and MCNP

International Nuclear Information System (INIS)

Lee, Kyung Hoon; Kim, Kang Seog; Noh, Jae Man; Song, Jae Seung; Zee, Sung Quun

2005-01-01

The latest research associated with the very high temperature gas-cooled reactor (VHTR) is focused on the verification of a system performance and safety under operating conditions for the VHTRs. As a part of those, an international gas-cooled reactor program initiated by IAEA is going on. The key objectives of this program are the validation of analytical computer codes and the evaluation of benchmark models for the projected and actual VHTRs. New reactor physics analysis procedure for the prismatic VHTR is under development by adopting the conventional two-step procedure. In this procedure, a few group constants are generated through the transport lattice calculations using the HELIOS code, and the core physics analysis is performed by the 3-dimensional nodal diffusion code MASTER. We evaluated the performance of the HELIOS/MASTER code package through the benchmark calculations related to the GT-MHR (Gas Turbine-Modular Helium Reactor) to dispose weapon plutonium. In parallel, MCNP is employed as a reference code to verify the results of the HELIOS/MASTER procedure

Type B package for the transport of large medical and industrial sources

International Nuclear Information System (INIS)

Brown, Darrell Dwaine; Noss, Philip W.

2010-01-01

AREVA Federal Services LLC, under contract to the Los Alamos National Laboratory's Offsite Source Recovery Project, is developing a new Type B(U)-96 package for the transport of unwanted or abandoned high activity gamma and neutron radioactive sealed sources (sources). The sources were used primarily in medical or industrial devices, and are of domestic (USA) or foreign origin. To promote public safety and mitigate the possibility of loss or misuse, the Offsite Source Recovery Project is recovering and managing sources worldwide. The package, denoted the LANL-B, is designed to accommodate the sources within an internal gamma shield. The sources are located either in the IAEA's Long Term Storage Shield (LTSS), or within intact medical or industrial irradiation devices. As the sources are already shielded separately, the package does not include any shielding of its own. A particular challenge in the design of the LANL-B has been weight. Since the LTSS shield weighs approximately 5,000 lb (2,270 kg), and the total package gross weight must be limited to 10,000 lb (4,540 kg), the net weight of the package was limited to 5,000 lb, for an efficiency of 50% (i.e., the payload weight is 50% of the gross weight of the package). This required implementation of a light-weight bell-jar concept, in which the containment takes the form of a vertical bell which is bolted to a base. A single impact limiter is used on the bottom, to protect the elastomer seals and bolted joint. A top-end impact is mitigated by the deformation of a tori spherically-shaped head. Impacts in various orientations on the bottom end are mitigated by a cylindrical, polyurethane foam-filled impact limiter. Internally, energy is absorbed using honeycomb blocks at each end, which fill the torispherical head volumes. As many of the sources are considered to be in normal form, the LANL-B package offers leak-tight containment using an elastomer seal at the joint between the bell and the base, as well as on the

CH-TRU Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2005-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-10-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

'ACTIV' - a package of codes for charged particle and neutron activation analysis

International Nuclear Information System (INIS)

Cincu, Em.; Alexandreanu, B.; Manu, V.; Moisa, V.

1997-01-01

The 'ACTIV' Program is an advanced software package dedicated to applications of the thermal neutron and charged particle activation (NAA and CPA) induced reactions. The program is designed to run on personal computers compatible IBM PC-Models XT/AT, 286 or more advanced, operating under DOS version 5.0 or later, on systems with minimum 5 MB of hard disk memory. The package consists of 6 software modules and a Nuclear Data Base comprising physical, nuclear reaction and decay data for: thermal neutron, proton, deuteron and α-particle induced reactions on 15 selected metallic elements; the nuclear reaction data corresponds to the energy range (5-100) MeV. In the first version - ACTIV 1.0 - the set of input data concerns: the sample type, irradiation and measurement conditions, the γ-ray spectrum identification code, selected detection efficiency calibration curve, selected radionuclides, selected standardization method for elemental analysis, version of results. At present, the 'ACTIV' package comprises 6 soft modules for processing the experimental data, which ensure computation of the quantities: radionuclide activities, activation yield data (case of CPA) and elemental concentration by relative and absolute standardization methods. Recently, the software designed to processing complex γ-ray spectra was acquired and installed on our PC 486 (8 MB RAM, 100 MHz). The next step in developing the 'ACTIV' program envisages improving the existing computing codes, completing the data libraries, incorporating a new soft for the direct use of the 'Quantum TM MCA' data, developing modules dedicated to uncertainty computation and optimization of the activation experiments

Extending R packages to support 64-bit compiled code: An illustration with spam64 and GIMMS NDVI3g data

Science.gov (United States)

Gerber, Florian; Mösinger, Kaspar; Furrer, Reinhard

2017-07-01

Software packages for spatial data often implement a hybrid approach of interpreted and compiled programming languages. The compiled parts are usually written in C, C++, or Fortran, and are efficient in terms of computational speed and memory usage. Conversely, the interpreted part serves as a convenient user-interface and calls the compiled code for computationally demanding operations. The price paid for the user friendliness of the interpreted component is-besides performance-the limited access to low level and optimized code. An example of such a restriction is the 64-bit vector support of the widely used statistical language R. On the R side, users do not need to change existing code and may not even notice the extension. On the other hand, interfacing 64-bit compiled code efficiently is challenging. Since many R packages for spatial data could benefit from 64-bit vectors, we investigate strategies to efficiently pass 64-bit vectors to compiled languages. More precisely, we show how to simply extend existing R packages using the foreign function interface to seamlessly support 64-bit vectors. This extension is shown with the sparse matrix algebra R package spam. The new capabilities are illustrated with an example of GIMMS NDVI3g data featuring a parametric modeling approach for a non-stationary covariance matrix.

Documentation of the seawater intrusion (SWI2) package for MODFLOW

Science.gov (United States)

Bakker, Mark; Schaars, Frans; Hughes, Joseph D.; Langevin, Christian D.; Dausman, Alyssa M.

2013-01-01

The SWI2 Package is the latest release of the Seawater Intrusion (SWI) Package for MODFLOW. The SWI2 Package allows three-dimensional vertically integrated variable-density groundwater flow and seawater intrusion in coastal multiaquifer systems to be simulated using MODFLOW-2005. Vertically integrated variable-density groundwater flow is based on the Dupuit approximation in which an aquifer is vertically discretized into zones of differing densities, separated from each other by defined surfaces representing interfaces or density isosurfaces. The numerical approach used in the SWI2 Package does not account for diffusion and dispersion and should not be used where these processes are important. The resulting differential equations are equivalent in form to the groundwater flow equation for uniform-density flow. The approach implemented in the SWI2 Package allows density effects to be incorporated into MODFLOW-2005 through the addition of pseudo-source terms to the groundwater flow equation without the need to solve a separate advective-dispersive transport equation. Vertical and horizontal movement of defined density surfaces is calculated separately using a combination of fluxes calculated through solution of the groundwater flow equation and a simple tip and toe tracking algorithm. Use of the SWI2 Package in MODFLOW-2005 only requires the addition of a single additional input file and modification of boundary heads to freshwater heads referenced to the top of the aquifer. Fluid density within model layers can be represented using zones of constant density (stratified flow) or continuously varying density (piecewise linear in the vertical direction) in the SWI2 Package. The main advantage of using the SWI2 Package instead of variable-density groundwater flow and dispersive solute transport codes, such as SEAWAT and SUTRA, is that fewer model cells are required for simulations using the SWI2 Package because every aquifer can be represented by a single layer of cells

Description of the DLC-99/HUGO package of photon interaction data in ENDF/B-V format

International Nuclear Information System (INIS)

Roussin, R.W.; Knight, J.R.; Hubbell, J.H.; Howerton, R.J.

1983-12-01

A new photon interaction data library, DLC,-99/HUGO, is described. The library was prepared by incorporating newly evaluated data from the National Bureau of Standards with that from an existing data library, DLC-7F/HPICE, which is the ENDF/B-IV photon interaction data. It contains pair and triplet cross sections, photoelectric cross sections, and atomic form factors and the corresponding coherent scattering cross sections. Evaluated data in INDF/B-V format are provided for elements Z=1 to 100. The data package, available from the Radiation Shielding Information Center (RSIC) at Oak Ridge National Laboratory, will be submitted to CSEWG for consideration as the ENDF/B-V Photon Interaction Library. Two computer codes, EDPHOT for selectively printing the data and COMP23 for comparing two photon interaction libraries, are also provided

ANITA-2000 activation code package - updating of the decay data libraries and validation on the experimental data of the 14 MeV Frascati Neutron Generator

Directory of Open Access Journals (Sweden)

Frisoni Manuela

2016-01-01

Full Text Available ANITA-2000 is a code package for the activation characterization of materials exposed to neutron irradiation released by ENEA to OECD-NEADB and ORNL-RSICC. The main component of the package is the activation code ANITA-4M that computes the radioactive inventory of a material exposed to neutron irradiation. The code requires the decay data library (file fl1 containing the quantities describing the decay properties of the unstable nuclides and the library (file fl2 containing the gamma ray spectra emitted by the radioactive nuclei. The fl1 and fl2 files of the ANITA-2000 code package, originally based on the evaluated nuclear data library FENDL/D-2.0, were recently updated on the basis of the JEFF-3.1.1 Radioactive Decay Data Library. This paper presents the results of the validation of the new fl1 decay data library through the comparison of the ANITA-4M calculated values with the measured electron and photon decay heats and activities of fusion material samples irradiated at the 14 MeV Frascati Neutron Generator (FNG of the NEA-Frascati Research Centre. Twelve material samples were considered, namely: Mo, Cu, Hf, Mg, Ni, Cd, Sn, Re, Ti, W, Ag and Al. The ratios between calculated and experimental values (C/E are shown and discussed in this paper.

BPACK -- A computer model package for boiler reburning/co-firing performance evaluations. User`s manual, Volume 1

Energy Technology Data Exchange (ETDEWEB)

Wu, K.T.; Li, B.; Payne, R.

1992-06-01

This manual presents and describes a package of computer models uniquely developed for boiler thermal performance and emissions evaluations by the Energy and Environmental Research Corporation. The model package permits boiler heat transfer, fuels combustion, and pollutant emissions predictions related to a number of practical boiler operations such as fuel-switching, fuels co-firing, and reburning NO{sub x} reductions. The models are adaptable to most boiler/combustor designs and can handle burner fuels in solid, liquid, gaseous, and slurried forms. The models are also capable of performing predictions for combustion applications involving gaseous-fuel reburning, and co-firing of solid/gas, liquid/gas, gas/gas, slurry/gas fuels. The model package is conveniently named as BPACK (Boiler Package) and consists of six computer codes, of which three of them are main computational codes and the other three are input codes. The three main codes are: (a) a two-dimensional furnace heat-transfer and combustion code: (b) a detailed chemical-kinetics code; and (c) a boiler convective passage code. This user`s manual presents the computer model package in two volumes. Volume 1 describes in detail a number of topics which are of general users` interest, including the physical and chemical basis of the models, a complete description of the model applicability, options, input/output, and the default inputs. Volume 2 contains a detailed record of the worked examples to assist users in applying the models, and to illustrate the versatility of the codes.

Structural and Thermal Safety Analysis Report for the Type B Radioactive Waste Transport Package

Energy Technology Data Exchange (ETDEWEB)

Kim, D. H.; Seo, K. S.; Lee, J. C.; Bang, K. S

2007-09-15

We carried out structural safety evaluation for the type B radioactive waste transport package. Requirements for type B packages according to the related regulations such as IAEA Safety Standard Series No. TS-R-1, Korea Most Act. 2001-23 and US 10 CFR Part 71 were evaluated. General requirements for packages such as those for a lifting attachment, a tie-down attachment and pressure condition were considered. For the type B radioactive waste transport package, the structural, thermal and containment analyses were carried out under the normal transport conditions. Also the safety analysis were conducted under the accidental transport conditions. The 9 m drop test, 1 m puncture test, fire test and water immersion test under the accidental transport conditions were consecutively done. The type B radioactive waste transport packages were maintained the structural and thermal integrities.

GEMSFITS: Code package for optimization of geochemical model parameters and inverse modeling

International Nuclear Information System (INIS)

Miron, George D.; Kulik, Dmitrii A.; Dmytrieva, Svitlana V.; Wagner, Thomas

2015-01-01

Highlights: • Tool for generating consistent parameters against various types of experiments. • Handles a large number of experimental data and parameters (is parallelized). • Has a graphical interface and can perform statistical analysis on the parameters. • Tested on fitting the standard state Gibbs free energies of aqueous Al species. • Example on fitting interaction parameters of mixing models and thermobarometry. - Abstract: GEMSFITS is a new code package for fitting internally consistent input parameters of GEM (Gibbs Energy Minimization) geochemical–thermodynamic models against various types of experimental or geochemical data, and for performing inverse modeling tasks. It consists of the gemsfit2 (parameter optimizer) and gfshell2 (graphical user interface) programs both accessing a NoSQL database, all developed with flexibility, generality, efficiency, and user friendliness in mind. The parameter optimizer gemsfit2 includes the GEMS3K chemical speciation solver ( (http://gems.web.psi.ch/GEMS3K)), which features a comprehensive suite of non-ideal activity- and equation-of-state models of solution phases (aqueous electrolyte, gas and fluid mixtures, solid solutions, (ad)sorption. The gemsfit2 code uses the robust open-source NLopt library for parameter fitting, which provides a selection between several nonlinear optimization algorithms (global, local, gradient-based), and supports large-scale parallelization. The gemsfit2 code can also perform comprehensive statistical analysis of the fitted parameters (basic statistics, sensitivity, Monte Carlo confidence intervals), thus supporting the user with powerful tools for evaluating the quality of the fits and the physical significance of the model parameters. The gfshell2 code provides menu-driven setup of optimization options (data selection, properties to fit and their constraints, measured properties to compare with computed counterparts, and statistics). The practical utility, efficiency, and

Occurrence of Furnonisins B2 and B4 in Retail Raisins

DEFF Research Database (Denmark)

Knudsen, Peter Boldsen; Mogensen, Jesper Mølgaard; Larsen, Thomas Ostenfeld

2011-01-01

Concerns that raisins may be contaminated by fumonisins stem from the persistent occurrence of Aspergillus niger spores on raisins and the recent discovery of fumonisin production by A. niger on grapes, which leads to the widespread occurrence of fumonisin B-2 in wine. This study presents an LC-M...... that the fumonisins are produced mainly during the drying process concomitant with the decreasing water activity. Analysis of multiple packages from one manufacturer showed a 3-fold package-to-package variation, suggesting that a few raisins per package are contaminated.......Concerns that raisins may be contaminated by fumonisins stem from the persistent occurrence of Aspergillus niger spores on raisins and the recent discovery of fumonisin production by A. niger on grapes, which leads to the widespread occurrence of fumonisin B-2 in wine. This study presents an LC...

RH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this program guidance document is to provide the technical requirements for use, operation, inspection, and maintenance of the RH-TRU 72-B Waste Shipping Package and directly related components. This document complies with the requirements as specified in the RH-TRU 72-B Safety Analysis Report for Packaging (SARP), and Nuclear Regulatory Commission (NRC) Certificate of Compliance (C of C) 9212. If there is a conflict between this document and the SARP and/or C of C, the C of C shall govern. The C of C states: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' It further states: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP tasks the Waste Isolation Pilot Plant (WIPP) Management and Operating (M and O) Contractor with assuring the packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with 10 Code of Federal Regulations (CFR) 1.8, 'Deliberate Misconduct.' Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the U.S. Department of Energy (DOE) Carlsbad Field Office (CBFO) shall be notified immediately. CBFO will evaluate the issue and notify the NRC if required. In accordance with 10 CFR Part 71, 'Packaging and Transportation of Radioactive Material,' certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21, 'Reporting of Defects and Noncompliance,' regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2006-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2005-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2004-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

International Nuclear Information System (INIS)

2008-01-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes 'shipping categories' that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the 'General Case,' which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for 'Close-Proximity Shipments' (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for 'Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-09-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-05-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-02-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-06-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-12-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2006-01-18

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-10-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-03-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-09-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2004-12-01

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-11-20

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-12-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-30

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-08-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-06-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codes and corresponding shipping categories for "Controlled Shipments

Thermal Upgrading of 9977 Radioactive Material (Ram) Type B Package

International Nuclear Information System (INIS)

Gupta, N.; Abramczyk, G.

2012-01-01

The 9977 package is a radioactive material package that was originally certified to ship Heat Sources and RTG contents up to 19 watts and it is now being reviewed to significantly expand its contents in support of additional DOE missions. Thermal upgrading will be accomplished by employing stacked 3013 containers, a 3013 aluminum spacer and an external aluminum sleeve for enhanced heat transfer. The 7th Addendum to the original 9977 package Safety Basis Report describing these modifications is under review for the DOE certification. The analyses described in this paper show that this well-designed and conservatively analyzed package can be upgraded to carry contents with decay heat up to 38 watts with some simple design modifications. The Model 9977 package has been designed as a replacement for the Department of Transportation (DOT) Fissile Specification 6M package. The 9977 package is a very versatile Type B package which is certified to transport and store a wide spectrum of radioactive materials. The package was analyzed quite conservatively to increase its usefulness and store different payload configurations. Its versatility is evident from several daughter packages such as the 9978 and H1700, and several addendums where the payloads have been modified to suit the Shipper's needs without additional testing.

Improvement of Level-1 PSA computer code package -A study for nuclear safety improvement-

International Nuclear Information System (INIS)

Park, Chang Kyu; Kim, Tae Woon; Ha, Jae Joo; Han, Sang Hoon; Cho, Yeong Kyun; Jeong, Won Dae; Jang, Seung Cheol; Choi, Young; Seong, Tae Yong; Kang, Dae Il; Hwang, Mi Jeong; Choi, Seon Yeong; An, Kwang Il

1994-07-01

This year is the second year of the Government-sponsored Mid- and Long-Term Nuclear Power Technology Development Project. The scope of this subproject titled on 'The Improvement of Level-1 PSA Computer Codes' is divided into three main activities : (1) Methodology development on the under-developed fields such as risk assessment technology for plant shutdown and external events, (2) Computer code package development for Level-1 PSA, (3) Applications of new technologies to reactor safety assessment. At first, in the area of PSA methodology development, foreign PSA reports on shutdown and external events have been reviewed and various PSA methodologies have been compared. Level-1 PSA code KIRAP and CCF analysis code COCOA are converted from KOS to Windows. Human reliability database has been also established in this year. In the area of new technology applications, fuzzy set theory and entropy theory are used to estimate component life and to develop a new measure of uncertainty importance. Finally, in the field of application study of PSA technique to reactor regulation, a strategic study to develop a dynamic risk management tool PEPSI and the determination of inspection and test priority of motor operated valves based on risk importance worths have been studied. (Author)

ZZ ORIGEN2.2-UPJ, A complete package of ORIGEN2 libraries based on JENDL-3.2 and JENDL-3.3

International Nuclear Information System (INIS)

Ishikawa, Makoto; Kataoka, Masaharu; Ohkawachi, Yasushi; Ohki, Shigeo; JIN, Tomoyuki; Katakura, Jun-ich; Suyama, Kenya; Yanagisawa, Hiroshi; Matsumoto, Hideki; ONOUE, Akira; Sasahara, Akihiro

2006-01-01

1 - Description: ORLIBJ32 is a package of the libraries for ORIGEN2 code based on JENDL-3.2(NEA-1642). The one grouped cross section data for PWR and BWR were compiled using the burnup calculation results by SWAT code. The FBR libraries were compiled by the analysis system used at JNC for FBR core calculation. The fission yield and decay constants data were also updated using the second version of the JNDC FP library. In ORLIBJ32, not only one-grouped cross section data but also variable actinide cross section data are prepared, using a code written in FORTRAN77. The routines should be linked to the Original ORIGEN2.1 program. The LWR Libraries are prepared based on the current PWR fuel assembly specification, and the FBR libraries are based on the request by the Japanese FBR researchers. Before compiling the libraries, the specification of fuel assembly was completely reviewed and evaluated by the members of Working Group in the Japanese Nuclear Data Committee, 'working group on the evaluation of the amount of isotope generation'. ORLIBJ33 is a new libraries based on JENDL-3.3 following the release of JENDL-3.3. The parameters used to prepare the library are the same as those of ORLIBJ32. The Original version or ORLIBJ33 is coupled with ORIGEN2.1. But after the release of ORIGEN2.2 from ORNL as CCC-0371 through RSICC, several requests for a combination with ORLIBJ33 and ORIGEN2.2 were received. During the development of ORLIBJ33, released as NEA-1642, authors found a problem in the library maker for FBR libraries, and consequently it was revised and tested in JNC-Oarai. This package 'ORIGEN2.2-UPJ' contains: - updated source code of ORIGEN2.2 of CCC-0371 to use ORLIBJ32 and ORLIBJ33, - all Original libraries in CCC-0371, - ORLIBJ32 in NEA-164/03 (but libraries for FBR are revised), - and ORLIBJ33. In this package, decay data based on the second version of the JNDC FP library and, photon and decay data libraries based on JENDL-3.3 are also included. NLB and NLIB

Analytical Design Package (ADP2): A computer aided engineering tool for aircraft transparency design

Science.gov (United States)

Wuerer, J. E.; Gran, M.; Held, T. W.

1994-01-01

The Analytical Design Package (ADP2) is being developed as a part of the Air Force Frameless Transparency Program (FTP). ADP2 is an integrated design tool consisting of existing analysis codes and Computer Aided Engineering (CAE) software. The objective of the ADP2 is to develop and confirm an integrated design methodology for frameless transparencies, related aircraft interfaces, and their corresponding tooling. The application of this methodology will generate high confidence for achieving a qualified part prior to mold fabrication. ADP2 is a customized integration of analysis codes, CAE software, and material databases. The primary CAE integration tool for the ADP2 is P3/PATRAN, a commercial-off-the-shelf (COTS) software tool. The open architecture of P3/PATRAN allows customized installations with different applications modules for specific site requirements. Integration of material databases allows the engineer to select a material, and those material properties are automatically called into the relevant analysis code. The ADP2 materials database will be composed of four independent schemas: CAE Design, Processing, Testing, and Logistics Support. The design of ADP2 places major emphasis on the seamless integration of CAE and analysis modules with a single intuitive graphical interface. This tool is being designed to serve and be used by an entire project team, i.e., analysts, designers, materials experts, and managers. The final version of the software will be delivered to the Air Force in Jan. 1994. The Analytical Design Package (ADP2) will then be ready for transfer to industry. The package will be capable of a wide range of design and manufacturing applications.

A computer code package for electron transport Monte Carlo simulation

International Nuclear Information System (INIS)

Popescu, Lucretiu M.

1999-01-01

A computer code package was developed for solving various electron transport problems by Monte Carlo simulation. It is based on condensed history Monte Carlo algorithm. In order to get reliable results over wide ranges of electron energies and target atomic numbers, specific techniques of electron transport were implemented such as: Moliere multiscatter angular distributions, Blunck-Leisegang multiscatter energy distribution, sampling of electron-electron and Bremsstrahlung individual interactions. Path-length and lateral displacement corrections algorithms and the module for computing collision, radiative and total restricted stopping powers and ranges of electrons are also included. Comparisons of simulation results with experimental measurements are finally presented. (author)

Remote-Handled Transuranic Content Codes

International Nuclear Information System (INIS)

2001-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document represents the development of a uniform content code system for RH-TRU waste to be transported in the 72-Bcask. It will be used to convert existing waste form numbers, content codes, and site-specific identification codes into a system that is uniform across the U.S. Department of Energy (DOE) sites.The existing waste codes at the sites can be grouped under uniform content codes without any lossof waste characterization information. The RH-TRUCON document provides an all-encompassing description for each content code and compiles this information for all DOE sites. Compliance with waste generation, processing, and certification procedures at the sites (outlined in this document foreach content code) ensures that prohibited waste forms are not present in the waste. The content code gives an overall description of the RH-TRU waste material in terms of processes and packaging, as well as the generation location. This helps to provide cradle-to-grave traceability of the waste material so that the various actions required to assess its qualification as payload for the 72-B cask can be performed. The content codes also impose restrictions and requirements on the manner in which a payload can be assembled. The RH-TRU Waste Authorized Methods for Payload Control (RH-TRAMPAC), Appendix 1.3.7 of the 72-B Cask Safety Analysis Report (SAR), describes the current governing procedures applicable for the qualification of waste as payload for the 72-B cask. The logic for this classification is presented in the 72-B Cask SAR. Together, these documents (RH-TRUCON, RH-TRAMPAC, and relevant sections of the 72-B Cask SAR) present the foundation and justification for classifying RH-TRU waste into content codes. Only content codes described in thisdocument can be considered for transport in the 72-B cask. Revisions to this document will be madeas additional waste qualifies for transport. Each content code uniquely

Scientific investigation plan for NNWSI WBS element 1.2.2.5.L: NNWSI waste package performance assessment: Revision 1

International Nuclear Information System (INIS)

Eggert, K.G.; O'Connell, W.J.; Lappa, D.A.

1986-01-01

Waste package performance assessment contains three broad categories of activities. These activities are: (1) development of a hydrothermal flow and transport model to test concepts to be used in establishing boundary conditions for performance calculations, and to interface EBS release calculations with total system performance calculations; (2) development of a waste package systems model to provide integrated deterministic assessments of performance and analyses of waste package designs; and (3) development of an uncertainty methodology for combination with the system model to perform probabilistic reliability and performance analysis waste package designs. The first category contains activities that aid in determining the scope of a separate, simplified set of hydrologic calculations needed to characterize the waste package environment for performance assessment calculations. The last two activity categories are directly concerned with waste package performance calculations. A rationale for each activity under these groups is presented. All of the activities of performance assessment are either code development or analyses of waste package problems

Verification of RRC Ki code package for neutronic calculations of WWER core with GD

International Nuclear Information System (INIS)

Aleshin, S.S.; Bolshagin, S.N.; Lazarenko, A.P.; Markov, A.V.; Pavlov, V.I.; Pavlovitchev, A.M.; Sidorenko, V.D.; Tsvetkov, V.M.

2001-01-01

The report presented is concerned with verification results of TVS-M/PERMAK-A/BIPR-7A code package for WWERs neutronic calculation as applied to calculation of systems containing U-GD pins. The verification is based on corresponded benchmark calculations, data critical experiments and on operation data obtained WWER units with Gd. The comparison results are discussed (Authors)

Energy meshing techniques for processing ENDF/B-VI cross sections using the AMPX code system

International Nuclear Information System (INIS)

Dunn, M.E.; Greene, N.M.; Leal, L.C.

1999-01-01

Modern techniques for the establishment of criticality safety for fissile systems invariably require the use of neutronic transport codes with applicable cross-section data. Accurate cross-section data are essential for solving the Boltzmann Transport Equation for fissile systems. In the absence of applicable critical experimental data, the use of independent calculational methods is crucial for the establishment of subcritical limits. Moreover, there are various independent modern transport codes available to the criticality safety analyst (e.g., KENO V.a., MCNP, and MONK). In contrast, there is currently only one complete software package that processes data from the Version 6 format of the Evaluated Nuclear Data File (ENDF) to a format useable by criticality safety codes. To facilitate independent cross-section processing, Oak Ridge National Laboratory (ORNL) is upgrading the AMPX code system to enable independent processing of Version 6 formats using state-of-the-art procedures. The AMPX code system has been in continuous use at ORNL since the early 1970s and is the premier processor for providing multigroup cross sections for criticality safety analysis codes. Within the AMPX system, the module POLIDENT is used to access the resonance parameters in File 2 of an ENDF/B library, generate point cross-section data, and combine the cross sections with File 3 point data. At the heart of any point cross-section processing code is the generation of a suitable energy mesh for representing the data. The purpose of this work is to facilitate the AMPX upgrade through the development of a new and innovative energy meshing technique for processing point cross-section data

CH-TRU Waste Content Codes (CH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2005-01-15

The CH-TRU Waste Content Codes (CH-TRUCON) document describes the inventory of the U.S. Department of Energy (DOE) CH-TRU waste within the transportation parameters specified by the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC). The CH-TRAMPAC defines the allowable payload for the Transuranic Package Transporter-II (TRUPACT-II) and HalfPACT packagings. This document is a catalog of TRUPACT-II and HalfPACT authorized contents and a description of the methods utilized to demonstrate compliance with the CH-TRAMPAC. A summary of currently approved content codes by site is presented in Table 1. The CH-TRAMPAC describes "shipping categories" that are assigned to each payload container. Multiple shipping categories may be assigned to a single content code. A summary of approved content codes and corresponding shipping categories is provided in Table 2, which consists of Tables 2A, 2B, and 2C. Table 2A provides a summary of approved content codes and corresponding shipping categories for the "General Case," which reflects the assumption of a 60-day shipping period as described in the CH-TRAMPAC and Appendix 3.4 of the CH-TRU Payload Appendices. For shipments to be completed within an approximately 1,000-mile radius, a shorter shipping period of 20 days is applicable as described in the CH-TRAMPAC and Appendix 3.5 of the CH-TRU Payload Appendices. For shipments to WIPP from Los Alamos National Laboratory (LANL), Nevada Test Site, and Rocky Flats Environmental Technology Site, a 20-day shipping period is applicable. Table 2B provides a summary of approved content codes and corresponding shipping categories for "Close-Proximity Shipments" (20-day shipping period). For shipments implementing the controls specified in the CH-TRAMPAC and Appendix 3.6 of the CH-TRU Payload Appendices, a 10-day shipping period is applicable. Table 2C provides a summary of approved content codesand corresponding shipping categories for "Controlled Shipments

The advantages of using standardized review procedures in certifying type B radioactive material packages

International Nuclear Information System (INIS)

Easton, E.P.; Faille, S.

2004-01-01

This paper presents the advantages of adopting well-documented standardized review practices for reviewing Type B package designs. The US experience using standardized review plans and guidance has shown them to be a valuable tool in achieving more consistent and efficient package reviews, in training and qualifying technical reviewers, and in enhancing public and industry understanding of the package certification process. In addition, the standardized review practices, as living documents, have proven to be an effective method of incorporating new technical advances into the review process, and have provided a vehicle to make that knowledge widely available to fellow reviewers, the public and industry. Canada implemented a new internal review process in early 2003 to standardize the review of applications for certification of Type B Packages. Based on the similarity of these approaches, the United States and Canada have started discussions on a A North American System for the unilateral approval of Type B (U) packages. This initiative is looking into how each country is currently reviewing transportation package applications to see if agreement can be reached on accepting Type B certifications on a reciprocal basis, i.e., without additional review. Based on the experience in Canada and the United States, the authors believe that the use of standardized review processes, coupled with the knowledge and experience resident in IAEA's Transportation Advisory Material (TS-G-1.1) and series of TECDOCS, could also be used to develop a standard internationally accepted review process that could enhance the acceptance of unilateral approvals for Type B packages

The advantages of using standardized review procedures in certifying type B radioactive material packages

Energy Technology Data Exchange (ETDEWEB)

Easton, E.P. [United States Nuclear Regulatory Commission, Washington, DC (United States); Faille, S. [Canadian Nuclear Safety Commission, Ottawa (Canada)

2004-07-01

This paper presents the advantages of adopting well-documented standardized review practices for reviewing Type B package designs. The US experience using standardized review plans and guidance has shown them to be a valuable tool in achieving more consistent and efficient package reviews, in training and qualifying technical reviewers, and in enhancing public and industry understanding of the package certification process. In addition, the standardized review practices, as living documents, have proven to be an effective method of incorporating new technical advances into the review process, and have provided a vehicle to make that knowledge widely available to fellow reviewers, the public and industry. Canada implemented a new internal review process in early 2003 to standardize the review of applications for certification of Type B Packages. Based on the similarity of these approaches, the United States and Canada have started discussions on a A North American System for the unilateral approval of Type B (U) packages. This initiative is looking into how each country is currently reviewing transportation package applications to see if agreement can be reached on accepting Type B certifications on a reciprocal basis, i.e., without additional review. Based on the experience in Canada and the United States, the authors believe that the use of standardized review processes, coupled with the knowledge and experience resident in IAEA's Transportation Advisory Material (TS-G-1.1) and series of TECDOCS, could also be used to develop a standard internationally accepted review process that could enhance the acceptance of unilateral approvals for Type B packages.

On the structure of Lattice code WIMSD-5B

International Nuclear Information System (INIS)

Kim, Won Young; Min, Byung Joo

2004-03-01

The WIMS-D code is a freely available thermal reactor physics lattice code used widely for thermal research and power reactor calculation. Now the code WIMS-AECL, developed on the basis of WIMS-D, has been used as one of lattice codes for the cell calculation in Canada and also, in 1998, the latest version WIMSD-5B is released for OECD/NEA Data Bank. While WIMS-KAERI was developed and has been used, originated from WIMS-D, in Korea, it was adjusted for the cell calculation of research reactor HANARO and so it has no confirmaty to CANDU reactor. Therefore, the code development applicable to cell calculation of CANDU reactor is necessary not only for technological independence and but also for the establishment of CANDU safety analysis system. A lattice code WIMSD-5B was analyzed in order to set the system of reactor physics computer codes, to be used in the assessment of void reactivity effect. In order to improve and validate WIMSD-5B code, the analysis of the structure of WIMSD-5B lattice code was made and so its structure, algorithm and the subroutines of WIMSD-5B were presented for the cluster type and the pij method modelling the CANDU-6 fuel

9977 TYPE B PACKAGING INTERNAL DATA COLLECTION FEASIBILITY TESTING - MAGNETIC FIELD COMMUNICATIONS

Energy Technology Data Exchange (ETDEWEB)

Shull, D.

2012-06-18

The objective of this report is to document the findings from proof-of-concept testing performed by the Savannah River National Laboratory (SRNL) R&D Engineering and Visible Assets, Inc. for the DOE Packaging Certification Program (PCP) to determine if RuBee (IEEE 1902.1) tags and readers could be used to provide a communication link from within a drum-style DOE certified Type B radioactive materials packaging. A Model 9977 Type B Packaging was used to test the read/write capability and range performance of a RuBee tag and reader. Testing was performed with the RuBee tags placed in various locations inside the packaging including inside the drum on the outside of the lid of the containment vessel and also inside of the containment vessel. This report documents the test methods and results. A path forward will also be recommended.

CORDSPW - Windows computer program package for graphical interpretation of CORD-2 data

International Nuclear Information System (INIS)

Slavic, S.; Kromar, M.

2007-01-01

The CORD-2 package, developed at Jozef Stefan Institute, enables determination of the core power distribution and reactivity. Core distributions data generated during the calculation process are stored in CORlib files. CORDSP code, which is a part of the CORD-2 package, displays and compares data contained in CORlib files. Since it runs in the DOS environment, there are several limitations in the presentation of desired data. A CORDSPW package runs in the Windows environment and offers better graphical interpretation of the CORlib data. Core distributions can be displayed, compared, rewritten in the new files and sent to the printer. The user can select the appropriate display of the presented data such as core symmetry, colour and fonts. Core radial and axial distributions can be presented and compared. There are several options to store and print data. The user can choose between standard ASCII and graphical JPG format. (author)

Improved numerical grid generation techniques for the B2 edge plasma code

International Nuclear Information System (INIS)

Stotler, D.P.; Coster, D.P.

1992-06-01

Techniques used to generate grids for edge fluid codes such as B2 from numerically computed equilibria are discussed. Fully orthogonal, numerically derived grids closely resembling analytically prescribed meshes can be obtained. But, the details of the poloidal field can vary, yielding significantly different plasma parameters in the simulations. The magnitude of these differences is consistent with the predictions of an analytic model of the scrape-off layer. Both numerical and analytic grids are insensitive to changes in their defining parameters. Methods for implementing nonorthogonal boundaries in these meshes are also presented; they differ slightly from those required for fully orthogonal grids

Aging management assessment of type B transportation packages

International Nuclear Information System (INIS)

Sullivan, G.J.; Stahmer, U.; Freeman, E.L.

2004-01-01

The condition of a physical system such as a radioactive materials transportation package can change as it ages. The degree to which aging effects are identified, prevented or mitigated will depend on the types of inspections and maintenance performed on the critical components of the system. Routine inspections and maintenance may not address degradation mechanisms that are difficult to observe and can act over long periods of time. Aging management is a systematic effort to ensure that the system performs as designed over its entire service life and that degradation mechanisms do not prematurely end the service life. The Nuclear Waste Management Division (NWMD) of Ontario Power Generation (OPG) has developed an Aging Management Procedure and began performing aging management assessments on its Type B(U) packages. This paper discusses the Procedure and briefly describes the aging management assessment performed on the Roadrunner Transportation Package to demonstrate a practical application of the aging management process

Application of the ASME code in designing containment vessels for packages used to transport radioactive materials

International Nuclear Information System (INIS)

Raske, D.T.; Wang, Z.

1992-01-01

The primary concern governing the design of shipping packages containing radioactive materials is public safety during transport. When these shipments are within the regulatory jurisdiction of the US Department of Energy, the recommended design criterion for the primary containment vessel is either Section III or Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code, depending on the activity of the contents. The objective of this paper is to discuss the design of a prototypic containment vessel representative of a packaging for the transport of high-level radioactive material

7 CFR Exhibit D to Subpart B of... - Designated Counties for Housing Application Packaging Grants

Science.gov (United States)

2010-01-01

... 7 Agriculture 13 2010-01-01 2009-01-01 true Designated Counties for Housing Application Packaging... Application Packaging Grants Pt. 1944, Subpt. B, Exh. D Exhibit D to Subpart B of Part 1944—Designated Counties for Housing Application Packaging Grants ER25my05.036 ER25my05.037 ER25my05.038 ER25my05.039 [70...

9978 AND 9975 TYPE B PACKAGING INTERNAL DATA COLLECTION FEASIBILITY TESTING

Energy Technology Data Exchange (ETDEWEB)

Fogle, R.

2012-05-07

The objective of this report is to document the findings from a series of proof-of-concept tests performed by Savannah River National Laboratory (SRNL) R and D Engineering, for the DOE Packaging Certification Program to determine if a viable radio link could be established from within the stainless steel confines of several drum-style DOE certified Type B radioactive materials packagings. Two in-hand, off-the-shelf radio systems were tested. The first system was a Wi-Fi Librestream Onsight{trademark} camera with a Fortress ES820 Access Point and the second was the On-Ramp Wireless Ultra-Link Processing{trademark} (ULP) radio system. These radio systems were tested within the Model 9975 and 9978 Type B packagings at the SRNL. This report documents the test methods and results. A path forward will also be recommended.

Code manual for MACCS2: Volume 1, user's guide

International Nuclear Information System (INIS)

Chanin, D.I.; Young, M.L.

1997-03-01

This report describes the use of the MACCS2 code. The document is primarily a user's guide, though some model description information is included. MACCS2 represents a major enhancement of its predecessor MACCS, the MELCOR Accident Consequence Code System. MACCS, distributed by government code centers since 1990, was developed to evaluate the impacts of severe accidents at nuclear power plants on the surrounding public. The principal phenomena considered are atmospheric transport and deposition under time-variant meteorology, short- and long-term mitigative actions and exposure pathways, deterministic and stochastic health effects, and economic costs. No other U.S. code that is publicly available at present offers all these capabilities. MACCS2 was developed as a general-purpose tool applicable to diverse reactor and nonreactor facilities licensed by the Nuclear Regulatory Commission or operated by the Department of Energy or the Department of Defense. The MACCS2 package includes three primary enhancements: (1) a more flexible emergency-response model, (2) an expanded library of radionuclides, and (3) a semidynamic food-chain model. Other improvements are in the areas of phenomenological modeling and new output options. Initial installation of the code, written in FORTRAN 77, requires a 486 or higher IBM-compatible PC with 8 MB of RAM

AMPX-77 Phase 1 certification package

Energy Technology Data Exchange (ETDEWEB)

Niemer, K.A.

1994-03-01

The AMPX-77 Phase 1 modules have been certified. AMPX-77 is a modular code system for generating coupled multigroup neutron-gamma cross section libraries from Evaluated Nuclear Data Files (ENDF/B). All basic cross-section data are input from the formats used by the ENDF/B, and output can be obtained from a variety of formats, included in its own internal and very general formats, along with a variety of other useful formats used by major transport, diffusion theory, and Monte Carlo codes. Processing is provided for both neutron and gamma-ray data. The AMPX-77 code system will be used at SRS to perform critical calculations related to nuclear criticality safety. The AMPX-77 modular codes system contains forty-seven separate modules. For the certification process, the 47 modules have been divided into three groups or phases. This Certification Package is for the Phase 1 modules: BONAMI, LAPHNGAS, MALOCS, NITAWL, ROLAIDS, SMUG, and XSDRNPM.

EMC3-eIRENE simulation of impurity transport in comparison with EUV emission measurements in the stochastic layer of LHD: effects of force balance and transport coefficients

Energy Technology Data Exchange (ETDEWEB)

Dai, S. [National Institute for Fusion Science, Toki (Japan); Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education), School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian (China); Kobayashi, M.; Morita, S.; Oishi, T.; Suzuki, Y. [National Institute for Fusion Science, Toki (Japan); Department of Fusion Science, School of Physical Sciences, SOKENDAI (The Graduate University for Advanced Studies), Toki (Japan); Kawamura, G. [National Institute for Fusion Science, Toki (Japan); Zhang, H.M.; Huang, X.L. [Department of Fusion Science, School of Physical Sciences, SOKENDAI (The Graduate University for Advanced Studies), Toki (Japan); Feng, Y. [Max-Planck-Institut fuer Plasmaphysik, Greifswald (Germany); Wang, D.Z. [Key Laboratory of Materials Modification by Laser, Ion and Electron Beams (Ministry of Education), School of Physics and Optoelectronic Technology, Dalian University of Technology, Dalian (China); Collaboration: The LHD experiment group

2016-08-15

The transport properties and line emissions of the intrinsic carbon in the stochastic layer of the Large Helical Device have been investigated with the three-dimensional edge transport code EMC3-EIRENE. The simulations of impurity transport and emissivity have been performed to study the dedicated experiment in which the carbon emission distributions are measured by a space-resolved EUV spectrometer system. A discrepancy of the CIV impurity emission between the measurement and simulation is obtained, which is studied with the variation of the ion thermal force, friction force and the perpendicular diffusivity in the impurity transport model. An enhanced ion thermal force or a reduced friction force in the modelling can increase the CIV impurity emission at the inboard X-point region. Furthermore, the impact of the perpendicular diffusivity Dimp is studied which shows that the CIV impurity emission pattern is very sensitive to Dimp. It is found that the simulation results with the increased Dimp tend to be closer to the experimental observation. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Containment analysis for Type B packages used to transport various contents

International Nuclear Information System (INIS)

Anderson, B.L.; Carlson, R.W.; Fischer, L.E.

1996-11-01

This report presents sample containment analyses and examples of leakage rate calculations for Type B packages used to transport various contents. Samples of acceptance standard leakage rates are developed for specific contents types at normal transport conditions and at hypothetical accident conditions. The leakage rates are expressed as allowable standard leakage rates. The type of contents considered include: (1) powders, (2) liquids, (3) irradiated fuel rods, (4) gases, and (5) solids

Safety Analysis Report for packaging (onsite) steel waste package

International Nuclear Information System (INIS)

BOEHNKE, W.M.

2000-01-01

The steel waste package is used primarily for the shipment of remote-handled radioactive waste from the 324 Building to the 200 Area for interim storage. The steel waste package is authorized for shipment of transuranic isotopes. The maximum allowable radioactive material that is authorized is 500,000 Ci. This exceeds the highway route controlled quantity (3,000 A 2 s) and is a type B packaging

A simplified computer code based on point Kernel theory for calculating radiation dose in packages of radioactive material

International Nuclear Information System (INIS)

1986-03-01

A study on radiation dose control in packages of radioactive waste from nuclear facilities, hospitals and industries, such as sources of Ra-226, Co-60, Ir-192 and Cs-137, is presented. The MAPA and MAPAM computer codes, based on point Kernel theory for calculating doses of several source-shielding type configurations, aiming to assure the safe transport conditions for these sources, was developed. The validation of the code for point sources, using the values provided by NCRP, for the thickness of lead and concrete shieldings, limiting the dose at 100 Mrem/hr for several distances from the source to the detector, was carried out. The validation for non point sources was carried out, measuring experimentally radiation dose from packages developed by Brazilian CNEN/S.P. for removing the sources. (M.C.K.) [pt

78 FR 26090 - Content Specifications and Shielding Evaluations for Type B Transportation Packages

Science.gov (United States)

2013-05-03

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0270] Content Specifications and Shielding Evaluations for...) 2013-04, ``Content Specifications and Shielding Evaluations for Type B Transportation Packages.'' This... Packages for Radioactive Material,'' for the review of content specifications and shielding evaluations...

Compliance assessment of an uranium hexafluoride package 30B with overpack to the IAEA standards

International Nuclear Information System (INIS)

Andreuccetti, P.; Aquaro, D.; Forasassi, G.; Beone, G.; Eletti, G.; Orsini, A.

1988-01-01

At the Dipartimento di Costruzioni Meccaniche e Nucleari (DCMN) of the Pisa University a research program was carried out in order to assess the compliance to the updated IAEA standards of the UF6 30B container, complete with its sandwich phenolic foam filled external overpack. The research program, performed in collaboration with ENEA and several interested Italian firms, included 9 mt free drop, perforation, thermal and leaktightness tests, on two complete packages with dummy load. The heat transfer conditions, with the UF6 real contents, were simulated by means of numerical analyses with the TRUMP computer code and calculation procedures set up using the available experimental data. The attained results seem to be useful from the point of view of the foreseen purposes

Remaining Sites Verification Package for the 126-B-2, 183-B Clearwells

International Nuclear Information System (INIS)

Dittmer, L.M.

2007-01-01

The 126-B-2, 183-B Clearwells were built as part of the 183-B Water Treatment Facility and are composed of 2 covered concrete reservoirs. The bulk of the water stored in the clearwells was used as process water to cool the 105-B Reactor and as a source of potable water. Residual conditions were determined to meet the remedial action objectives specified in the Remaining Sites ROD through an evaluation of the available process knowledge. The results of the evaluation do not preclude any future uses and allow for unrestricted use of shallow zone soils. The results also indicate that residual concentrations are protective of groundwater and the Columbia River.

Cleanup Verification Package for the 118-B-1, 105-B Solid Waste Burial Ground

International Nuclear Information System (INIS)

Capron, J.M.

2008-01-01

This cleanup verification package documents completion of remedial action, sampling activities, and compliance criteria for the 118-B-1, 105-B Solid Waste Burial Ground. This waste site was the primary burial ground for general wastes from the operation of the 105-B Reactor and P-10 Tritium Separation Project and also received waste from the 105-N Reactor. The burial ground received reactor hardware, process piping and tubing, fuel spacers, glassware, electrical components, tritium process wastes, soft wastes and other miscellaneous debris

The Cloud Feedback Model Intercomparison Project Observational Simulator Package: Version 2

Science.gov (United States)

Swales, Dustin J.; Pincus, Robert; Bodas-Salcedo, Alejandro

2018-01-01

The Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP) gathers together a collection of observation proxies or satellite simulators that translate model-simulated cloud properties to synthetic observations as would be obtained by a range of satellite observing systems. This paper introduces COSP2, an evolution focusing on more explicit and consistent separation between host model, coupling infrastructure, and individual observing proxies. Revisions also enhance flexibility by allowing for model-specific representation of sub-grid-scale cloudiness, provide greater clarity by clearly separating tasks, support greater use of shared code and data including shared inputs across simulators, and follow more uniform software standards to simplify implementation across a wide range of platforms. The complete package including a testing suite is freely available.

Safety Analysis Report for packaging (onsite) steel waste package

Energy Technology Data Exchange (ETDEWEB)

BOEHNKE, W.M.

2000-07-13

The steel waste package is used primarily for the shipment of remote-handled radioactive waste from the 324 Building to the 200 Area for interim storage. The steel waste package is authorized for shipment of transuranic isotopes. The maximum allowable radioactive material that is authorized is 500,000 Ci. This exceeds the highway route controlled quantity (3,000 A{sub 2}s) and is a type B packaging.

First Results for Fluid Dynamics, Neutronics and Fission Product Behaviour in HTR applying the HTR Code Package (HCP) Prototype

International Nuclear Information System (INIS)

Allelein, H.-J.; Kasselmann, S.; Xhonneux, A.; Lambertz, D.

2014-01-01

To simulate the different aspects of High Temperature Reactor (HTR) cores, a variety of specialized computer codes have been developed at Forschungszentrum Jülich (IEK-6) and Aachen University (LRST) in the last decades. In order to preserve knowledge, to overcome present limitations and to make these codes applicable to modern computer clusters, these individual programs are being integrated into a consistent code package. The so-called HTR code package (HCP) couples the related and recently applied physics models in a highly integrated manner and therefore allows to simulate phenomena with higher precision in space and time while at the same time applying state-of-the-art programming techniques and standards. This paper provides an overview of the status of the HCP and reports about first benchmark results for an HCP prototype which couples the fluid dynamics and time dependent neutronics code MGT-3D, the burn up code TNT and the fission product release code STACY. Due to the coupling of MGT-3D and TNT, a first step towards a new reactor operation and accident simulation code was made, where nuclide concentrations calculated by TNT are fed back into a new spectrum code of the HCP. Selected operation scenarios of the HTR-Module 200 concept plant and the HTTR were chosen to be simulated with the HCP prototype. The fission product release during normal operation conditions will be calculated with STACY based on a core status derived from SERPENT and MGT–3D. Comparisons will be shown against data generated by the legacy codes VSOP99/11, NAKURE and FRESCO-II. (author)

Validation of DRAGON code in connection with WIMS-AECL/RFSP code system based on ENDF/B-VI library and two group model

International Nuclear Information System (INIS)

Hong, In Seob; Suk, Ho Chun; Kim, Soon Young; Jo, Chang Keun

2002-06-01

The major objective of this research is to validate the incremental cross section property of DRAGON code in connection with WIMS-AECL/DRAGON/RFSP code system with ENDF/B-VI library and full 2G calculation model. The direct comparison between the incremental cross section results calculated by DRAGON with ENDF/B-VI and ENDF/B-V and MULTICELL with ENDF/B-V indicate that there are not much differences between the incremental cross sections of DRAGON with ENDF/B-V and ENDF/B-VI, but there exists large discrepancies between the results of DRAGON and those of MULTICELL. In the analysis of the difference between calculated and measured reactivity worths of various types of control devices during Phase-B Post-Simulation of Wolsong Units 2, 3 and 4, WIMS-AECL/DRAGON/RFSP analysis well agrees with those of previous WIMS-AECL /MULTICELL/RFSP analysis within very small differences. From those results, we can conclude that DRAGON code can be used as a general purpose incremental cross section generation tool for not only the natural uranium fuel but also slightly enriched fuel such as RU or SEU, to cover the shortcomings of natural uranium based MULTICELL code

21 CFR 106.90 - Coding.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Coding. 106.90 Section 106.90 Food and Drugs FOOD... of Infant Formulas § 106.90 Coding. The manufacturer shall code all infant formulas in conformity with the coding requirements that are applicable to thermally processed low-acid foods packaged in...

Proposal of an alternative upper divertor in ASDEX Upgrade supported by EMC3-EIRENE simulations

Directory of Open Access Journals (Sweden)

T. Lunt

2017-08-01

Full Text Available We discuss the benefits of installing a pair of in-vessel coils with currents |Ifx| ≲ 50 kAt in the upper divertor of ASDEX Upgrade (AUG to study a series of ‘alternative’ divertor configurations, like the Snowflake (SF and the X-divertor (XD, that are currently considered as alternative solutions for the power exhaust problem. The possibility of operating the standard lower single-null (SN and double-null (DN would be preserved. Potential effects to reduce the peak parallel- and/or perpendicular heat flux are predicted from a simple geometrical-diffusive model as well as by numerical EMC3-EIRENE simulations for pure deuterium attached conditions with spatially constant diffusion coefficients. Beyond that a series of other potential transport- and radiation related heat flux mitigation effects are identified and could be studied experimentally with the modified upper divertor in the high-power divertor Tokamak AUG.

Modeling cross-field drifts and current with the B2 code for the CIT divertor

International Nuclear Information System (INIS)

Rognlien, T.D.; Milovich, J.L.; Rensink, M.E.

1990-01-01

We have modified the B2 edge-plasma code to include the effects of classical fluid drifts across the magnetic field lines and plasma currents. This report presents preliminary results of these effects for the CIT parameter regime. The basic plasma model described by Braams involves solving the continuity equation, the parallel momentum balance equation, and separate energy balance equations for the ions and the electrons. If multiple ion species are present, they are all assumed to have a common temperature, but their densities and parallel velocities are solved for using additional continuity and parallel momentum balance equations for each species. Momentum and heat transport parallel to the magnetic field, B, are given by the classical collisional theory. On the other hand, transport perpendicular to B is represented by anomalous diffusion coefficients which are adjusted to agree with experimental measurements. These transport coefficients are generally taken to be constant in radius and poloidal angle, although this is not necessary. The goal of our work has been to include both the classical cross-field drift terms and the effects of parallel currents in the equations used in the B2 code. The motivation for including the cross-field terms comes from simple model calculations which indicate that the classical flows can contribute an important asymmetry which may help explain the transition from L-mode to H-mode confinement. Radial electric fields which arise near the separatrix cause E x B poloidal rotation which may also be related to the L-to-H mode transition through its effect on edge turbulence. Including the parallel currents is done to provide a tool for understanding the biased divertor experiments on DIII-D at General Atomics. Such biasing may provide an effective means of controlling the asymmetry of the power flow to different divertor plates

Transportation package design using numerical optimization

International Nuclear Information System (INIS)

Harding, D.C.; Witkowski, W.R.

1993-01-01

Since the design of transportation packages involves a complex coupling of structural, thermal and radiation shielding analyses and must follow very strict design constraints, numerical optimization provides the potential for more efficient container designs. In numerical optimization, the requirements of the design problem are mathematically formulated through the use of an objective function and constraints. The objective function(s), e.g., package weight, cost, volume, or combination thereof, is the function to be minimized or maximized by altering a set of design variables that define the package's shape and dimensions. Constraints are limitations on the performance of the system, such as resisting structural and thermal accident environments. Two constraints defined for an example wire mesh composite Type B package are: 1) deformation in the containment vessel seal region remains small enough throughout the 10 CFR-71 accident conditions to meet containment criteria, and 2) the elastomeric seal region remains below its operational temperature limit to guarantee seal integrity in the fire environment. The first constraint of a minimum energy absorbing layer thickness is evaluated with finite element analyses of the proposed dynamic crush accident criteria. The second constraint is evaluated with a 1-D transient thermal finite difference code parametrized for variable composite layer thicknesses, and is integrated with the optimization process. (J.P.N.)

To be or not B2B?

CERN Document Server

Symons, L J

2001-01-01

La question du commerce électronique interentreprises par le web (Business to Business, B2B) est posée actuellement par les grands groupes industriels impliqués dans le commerce mondial. Les prévisions sont imposantes, le B2B atteindra le C.A. de 3000 milliards de dollars en 2003. Les conditions d'accès, la façon de procéder des deux organisateurs (ARIBA et COMMERCE ONE) des plus grandes places de marchés actuelles, sont décrites. La base de l'énorme pyramide est le catalogue électronique multilingue UNSPSC (United Nations Standard Products and Services Classification) et l'organisation ECCMA (Electronic Commerce Code Management Association) qui gère le développement des UNSPSC codes en 8 langues. Dans ce contexte, l'auteur (re)-déclare qu'un des efforts principaux à fournir par le CERN est la création de son propre catalogue électronique. Dans la Division ST, une aide partielle à ce vaste programme pourrait être apportée par la normalisation des codes et désignations des pièces de maint...

Code manual for MACCS2: Volume 1, user`s guide

Energy Technology Data Exchange (ETDEWEB)

Chanin, D.I.; Young, M.L.

1997-03-01

This report describes the use of the MACCS2 code. The document is primarily a user`s guide, though some model description information is included. MACCS2 represents a major enhancement of its predecessor MACCS, the MELCOR Accident Consequence Code System. MACCS, distributed by government code centers since 1990, was developed to evaluate the impacts of severe accidents at nuclear power plants on the surrounding public. The principal phenomena considered are atmospheric transport and deposition under time-variant meteorology, short- and long-term mitigative actions and exposure pathways, deterministic and stochastic health effects, and economic costs. No other U.S. code that is publicly available at present offers all these capabilities. MACCS2 was developed as a general-purpose tool applicable to diverse reactor and nonreactor facilities licensed by the Nuclear Regulatory Commission or operated by the Department of Energy or the Department of Defense. The MACCS2 package includes three primary enhancements: (1) a more flexible emergency-response model, (2) an expanded library of radionuclides, and (3) a semidynamic food-chain model. Other improvements are in the areas of phenomenological modeling and new output options. Initial installation of the code, written in FORTRAN 77, requires a 486 or higher IBM-compatible PC with 8 MB of RAM.

Remote-Handled Transuranic Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2006-12-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

First results for fluid dynamics, neutronics and fission product behavior in HTR applying the HTR code package (HCP) prototype

Energy Technology Data Exchange (ETDEWEB)

Allelein, H.-J., E-mail: h.j.allelein@fz-juelich.de [Forschungszentrum Jülich, 52425 Jülich (Germany); Institute for Reactor Safety and Reactor Technology, RWTH Aachen University, 52064 Aachen (Germany); Kasselmann, S.; Xhonneux, A.; Tantillo, F.; Trabadela, A.; Lambertz, D. [Forschungszentrum Jülich, 52425 Jülich (Germany)

2016-09-15

To simulate the different aspects of High Temperature Reactor (HTR) cores, a variety of specialized computer codes have been developed at Forschungszentrum Jülich (IEK-6) and Aachen University (LRST) in the last decades. In order to preserve knowledge, to overcome present limitations and to make these codes applicable to modern computer clusters, these individual programs are being integrated into a consistent code package. The so-called HTR code package (HCP) couples the related and recently applied physics models in a highly integrated manner and therefore allows to simulate phenomena with higher precision in space and time while at the same time applying state-of-the-art programming techniques and standards. This paper provides an overview of the status of the HCP and reports about first benchmark results for an HCP prototype which couples the fluid dynamics and time dependent neutronics code MGT-3D, the burn up code TNT and the fission product release code STACY. Due to the coupling of MGT-3D and TNT, a first step towards a new reactor operation and accident simulation code was made, where nuclide concentrations calculated by TNT lead to new cross sections, which are fed back into MGT-3D. Selected operation scenarios of the HTR-Module 200 concept plant and the HTTR were chosen to be simulated with the HCP prototype. The fission product release during normal operation conditions will be calculated with STACY based on a core status derived from SERPENT and MGT-3D. Comparisons will be shown against data generated by SERPENT and the legacy codes VSOP99/11, NAKURE and FRESCO-II.

Packaging Review Guide for Reviewing Safety Analysis Reports for Packagings

Energy Technology Data Exchange (ETDEWEB)

DiSabatino, A; Biswas, D; DeMicco, M; Fisher, L E; Hafner, R; Haslam, J; Mok, G; Patel, C; Russell, E

2007-04-12

This Packaging Review Guide (PRG) provides guidance for Department of Energy (DOE) review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE Order 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his or her review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. This PRG is generally organized at the section level in a format similar to that recommended in Regulatory Guide 7.9 (RG 7.9). One notable exception is the addition of Section 9 (Quality Assurance), which is not included as a separate chapter in RG 7.9. Within each section, this PRG addresses the technical and regulatory bases for the review, the manner in which the review is accomplished, and findings that are generally applicable for a package that meets the approval standards. This Packaging Review Guide (PRG) provides guidance for DOE review and approval of packagings to transport fissile and Type B quantities of radioactive material. It fulfills, in part, the requirements of DOE O 460.1B for the Headquarters Certifying Official to establish standards and to provide guidance for the preparation of Safety Analysis Reports for Packagings (SARPs). This PRG is intended for use by the Headquarters Certifying Official and his review staff, DOE Secretarial offices, operations/field offices, and applicants for DOE packaging approval. The primary objectives of this PRG are to: (1) Summarize the regulatory requirements for package approval; (2) Describe the technical review procedures by which DOE determines that these requirements have been satisfied; (3) Establish and maintain the quality and uniformity of reviews; (4) Define the base from which to evaluate proposed changes in scope

A regulator's perspective on physical testing for type B packages

International Nuclear Information System (INIS)

Brach, William E.

2004-01-01

The U.S. Nuclear Regulatory Commission has a great deal of experience certifying Type B transport packages as complying with the regulations in 10 CFR Part 71. With this experience base, supporting risk studies, and with an exceptional historical safety record for transport, we are very confident in both the current regulations and the methods we use to review and certify transportation packages. Nevertheless, we have a responsibility to remain vigilant and review our regulations and implementing practices with a view towards continuous improvement. NRC regulations permit certification through testing, analyses, comparison to similar approved designs, or combinations of these methods. Testing can be further broken into scale models, components, simple models, or full-scale models. NRC does not require full-scale testing for certification of any package; however, many applicants for package certification have conducted a physical testing program to demonstrate that the package design meets the hypothetical accident conditions. The plans for a repository at Yucca Mountain have raised significant interest in the United States of America in transportation of spent fuel, and created a broad stakeholder and public interest in transportation package testing. As an expected large increase in the number of spent fuel transports nears, this interest will likely grow. The technical and regulatory reasons for, or for not, performing tests need to be well understood and communicated to all stakeholders

New version: GRASP2K relativistic atomic structure package

Science.gov (United States)

Jönsson, P.; Gaigalas, G.; Bieroń, J.; Fischer, C. Froese; Grant, I. P.

2013-09-01

A revised version of GRASP2K [P. Jönsson, X. He, C. Froese Fischer, I.P. Grant, Comput. Phys. Commun. 177 (2007) 597] is presented. It supports earlier non-block and block versions of codes as well as a new block version in which the njgraf library module [A. Bar-Shalom, M. Klapisch, Comput. Phys. Commun. 50 (1988) 375] has been replaced by the librang angular package developed by Gaigalas based on the theory of [G. Gaigalas, Z.B. Rudzikas, C. Froese Fischer, J. Phys. B: At. Mol. Phys. 30 (1997) 3747, G. Gaigalas, S. Fritzsche, I.P. Grant, Comput. Phys. Commun. 139 (2001) 263]. Tests have shown that errors encountered by njgraf do not occur with the new angular package. The three versions are denoted v1, v2, and v3, respectively. In addition, in v3, the coefficients of fractional parentage have been extended to j=9/2, making calculations feasible for the lanthanides and actinides. Changes in v2 include minor improvements. For example, the new version of rci2 may be used to compute quantum electrodynamic (QED) corrections only from selected orbitals. In v3, a new program, jj2lsj, reports the percentage composition of the wave function in LSJ and the program rlevels has been modified to report the configuration state function (CSF) with the largest coefficient of an LSJ expansion. The bioscl2 and bioscl3 application programs have been modified to produce a file of transition data with one record for each transition in the same format as in ATSP2K [C. Froese Fischer, G. Tachiev, G. Gaigalas, M.R. Godefroid, Comput. Phys. Commun. 176 (2007) 559], which identifies each atomic state by the total energy and a label for the CSF with the largest expansion coefficient in LSJ intermediate coupling. All versions of the codes have been adapted for 64-bit computer architecture. Program SummaryProgram title: GRASP2K, version 1_1 Catalogue identifier: ADZL_v1_1 Program summary URL: http://cpc.cs.qub.ac.uk/summaries/ADZL_v1_1.html Program obtainable from: CPC Program Library

The Cloud Feedback Model Intercomparison Project Observational Simulator Package: Version 2

Directory of Open Access Journals (Sweden)

D. J. Swales

2018-01-01

Full Text Available The Cloud Feedback Model Intercomparison Project Observational Simulator Package (COSP gathers together a collection of observation proxies or satellite simulators that translate model-simulated cloud properties to synthetic observations as would be obtained by a range of satellite observing systems. This paper introduces COSP2, an evolution focusing on more explicit and consistent separation between host model, coupling infrastructure, and individual observing proxies. Revisions also enhance flexibility by allowing for model-specific representation of sub-grid-scale cloudiness, provide greater clarity by clearly separating tasks, support greater use of shared code and data including shared inputs across simulators, and follow more uniform software standards to simplify implementation across a wide range of platforms. The complete package including a testing suite is freely available.

Structural Evaluation on HIC Transport Packaging under Accident Conditions

International Nuclear Information System (INIS)

Chung, Sung Hwan; Kim, Duck Hoi; Jung, Jin Se; Yang, Ke Hyung; Lee, Heung Young

2005-01-01

HIC transport packaging to transport a high integrity container(HIC) containing dry spent resin generated from nuclear power plants is to comply with the regulatory requirements of Korea and IAEA for Type B packaging due to the high radioactivity of the content, and to maintain the structural integrity under normal and accident conditions. It must withstand 9 m free drop impact onto an unyielding surface and 1 m drop impact onto a mild steel bar in a position causing maximum damage. For the conceptual design of a cylindrical HIC transport package, three dimensional dynamic structural analysis to ensure that the integrity of the package is maintained under all credible loads for 9 m free drop and 1 m puncture conditions were carried out using ABAQUS code.

ICRF induced edge plasma convection in ASDEX upgrade

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wei [Max Planck Institute for Plasma Physics, Garching/Greifswald (Germany); University of Ghent, Ghent (Belgium); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Feng, Yuehe; Lunt, Tilmann; Jacquot, Jonathan; Coster, David; Bilato, Roberto; Bobkov, Volodymyr; Ochoukov, Roman [Max Planck Institute for Plasma Physics, Garching/Greifswald (Germany); Noterdaeme, Jean-Marie [Max Planck Institute for Plasma Physics, Garching/Greifswald (Germany); University of Ghent, Ghent (Belgium); Colas, Laurent [CEA, IRFM, Saint-Paul-Lez-Durance (France); Collaboration: ASDEX Upgrade Team

2016-07-01

Ion Cyclotron Range of Frequency (ICRF) heating is one of the main auxiliary plasma heating methods in tokamaks. It relies on the fast wave to heat the plasma. However the slow wave can also be generated parasitically. The parallel electric field of the slow wave can induce large biased plasma potential through sheath rectification. The rapid variation of this rectified potential across the magnetic field can cause significant E x B convection in the Scrape-Off Layer (SOL). The ICRF induced convection can affect the SOL density, influence the ICRF power coupling and enhance the strength of plasma-wall interactions. To explore these physics, we not only show the experimental evidences in ASDEX Upgrade, but also present the associated simulation results with the 3D edge plasma fluid code EMC3-Eirene. Further simulations via combination of EMC3-Eirene and a sheath code SSWICH in an iterative and quasi self-consistent way can give good predictions for future experiments.

Exact comparison of dose rate measurements and calculation of TN12/2 packages

International Nuclear Information System (INIS)

Taniuchi, H.; Matsuda, F.

1998-01-01

Both of dose rate measurements of TN 12/2 package and calculations by Monte Carlo code MORSE in SCALE code system and MCNP were performed to evaluate the difference between the measurement and the calculation and finding out the cause of the difference. The calculated gamma-ray dose rates agreed well with measured ones, but calculated neutron dose rates overestimated more than a factor of 1.7. When considering the cause of the difference and applying the modification into the neutron calculation, the calculated neutron dose rates become to agree well, and the factor decreased to around 1.3. (authors)

Some benchmark calculations for VVER-1000 assemblies by WIMS-7B code

International Nuclear Information System (INIS)

Sultanov, N.V.

2001-01-01

Our aim in this report is to compare of calculation results, obtained with the use of different libraries, which are in the variant of the WIMS7B code. We had the three libraries: the 1986 library is based on the UKNDL files, the two 1996 libraries are based on the JEF-2.2 files, the one having the 69 group approximation, the other having the 172 group approximation. We wanted also to have some acquaintance with the new option of WIMS-7B - CACTUS. The variant of WIMS-7B was placed at our disposal by the code authors for a temporal use for 9 months. It was natural to make at comparisons with analogous values of TVS-M, MCU, Apollo-2, Casmo-4, Conkemo, MCNP, HELIOS codes, where the other different libraries were used. In accordance with our aims the calculations of unprofiled and profiled assemblies of the VVER-1000 reactor have been carried out by the option CACTUS. This option provides calculations by the characteristics method. The calculation results have been compared with the K ∞ values obtained by other codes in work. The conclusion from this analysis is such: the methodical parts of errors of these codes have nearly the same values. Spacing for K eff values can be explained of the library microsections differences mainly. Nevertheless, the more detailed analysis of the results obtained is required. In conclusion the calculation of a depletion of VVER-1000 cell has been carried out. The comparison of the dependency of the multiply factor from the depletion obtained by WIMS-7B with different libraries and by the TVS-M, MCU, HELIOS and WIMS-ABBN codes in work has been performed. (orig.)

Electroless Ni-B plating on SiO2 with 3-aminopropyl-triethoxysilane as a barrier layer against Cu diffusion for through-Si via interconnections in a 3-dimensional multi-chip package

International Nuclear Information System (INIS)

Ikeda, Akihiro; Sakamoto, Atsushi; Hattori, Reiji; Kuroki, Yukinori

2009-01-01

Electroless Ni-B was plated on SiO 2 as a barrier layer against Cu diffusion for through-Si via (TSV) interconnections in a 3-dimensional multi-chip package. The electroless Ni-B was deposited on the entire area of the SiO 2 side wall of a deep via with vapor phase pre-deposition of 3-aminopropyl-triethoxysilane on the SiO 2 . The carrier lifetimes in the Si substrates plated with Ni-B/Cu did not decrease with an increase in annealing temperature up to 400 deg. C . The absence of degradation of carrier lifetimes indicates that Cu atoms did not diffuse into the Si through the Ni-B. The advantages of electroless Ni-B (good conformal deposition and forming an effective diffusion barrier against Cu) make it useful as a barrier layer for TSV interconnections in a 3-dimensional multi-chip package

Type B plutonium transport package development that uses metallic filaments and composite materials

International Nuclear Information System (INIS)

Pierce, J.D.; Moya, J.L.; McClure, J.D.; Hohnstreiter, G.F.; Golliher, K.G.

1991-01-01

A new package was developed for transporting Pu and U quantities that are currently carried in DOT-6M packages. It uses double containment with threaded closures and elastomeric seals. A composite overpack of metallic wire mesh and ceramic or quartz cloth insulation is provided for protection in accidents. Two prototypes were subjected to dynamic crush tests. A thermal computer model was developed and benchmarked by test results to predict package behavior in fires. The material performed isotropically in a global fashion. A Type B Pu transport package can be developed for DOE Pu shipments for less than $5000 if manufactured in quantity. 5 figs, 6 refs

49 CFR Appendix B to Part 173 - Procedure for Testing Chemical Compatibility and Rate of Permeation in Plastic Packaging and...

Science.gov (United States)

2010-10-01

... Rate of Permeation in Plastic Packaging and Receptacles B Appendix B to Part 173 Transportation Other... Plastic Packaging and Receptacles 1. The purpose of this procedure is to determine the chemical compatibility and permeability of liquid hazardous materials packaged in plastic packaging and receptacles...

The CNCSN-2: One, two-and three-dimensional coupled neutral and charged particle discrete ordinates code system

International Nuclear Information System (INIS)

Voloschenko, A. M.; Gukov, S. V.; Russkov, A. A.; Gurevich, M. I.; Shkarovsky, D. A.; Kryuchkov, V. P.; Sumaneev, O. V.; Dubinin, A. A.

2009-01-01

KATRIN, KASKAD-Sand ROZ-6 codes solve the multigroup transport equation for neutrons, photons and charged particles in 3D. BOT3P-5., ConDat can be used as preprocessor. ARVES-2.5, a cross-section preprocessor (the package of utilities for operating with the cross section file in FMAC-M format) is included. Auxiliary codes MIXERM, CEPXS-BFP, CEPXS-BFP, SADCO-2.4 and CNCSN-2 are used

RH-TRU Waste Content Codes (RH TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: (1) A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. (2) A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is ''3''. The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

THYDE-B1/MOD2: a computer code for analysis of small-break loss-of-coolant accidents of boiling water reactors

International Nuclear Information System (INIS)

Nakamura, Hideo; Muramatsu, Ken; Kukita, Yutaka; Tasaka, Kanji

1988-04-01

THYDE-B1/MOD2 is a fast-running best estimate (BE) computer code to analyze thermal-hydraulic behaviors of the reactor cooling system of a boiling water reactor (BWR), mainly, during a small-break loss-of-coolant accident (SBLOCA) with a special emphasis on the behavior of pressure and mixture level in the pressure vessel. The coolant behavior is simulated with a volume-and-junction method based on assumptions of thermal equilibrium and homogeneous conditions for two-phase flow. A characteristic feature of this code is a three-region representation of the state of the coolant in a control volume, in which three regions consist of subcooled liquid, saturated mixture and saturated steam regions from the volume bottom. The regions are separated by two horizontal moving boundaries which are tracked by mass and energy balances for each region. With this three region node model, the interior of the pressure vessel can be represented by only two volumes: one for inside of the shroud and the other for outside, while other portions of the system are treated with homogeneous node model. This method, although it seems to be very simple, has been verified to be adequate for cases of BWR SBLOCAs in which the thermal-hydraulic behavior is relatively slow and gravity controlled. The code has been improved and modified from the last version of the code, THYDE-B1/MOD1, especially in the phase separation model which is used in the mixture level calculation in the three region node model. Then, a good predictability of the code has been indicated through the comparison of calculated results with various SBLOCA test data including ROSA-III of JAERI and FIST of the General Electric Co. This report presents the code modifications and input data requirements of the THYDE-B1/MOD2 code. (author)

RH-TRU Waste Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-07-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

Hamor-2: a computer code for LWR inventory calculation

International Nuclear Information System (INIS)

Guimaraes, L.N.F.; Marzo, M.A.S.

1985-01-01

A method for calculating the accuracy inventory of LWR reactors is presented. This method uses the Hamor-2 computer code. Hamor-2 is obtained from the coupling of two other computer codes Hammer-Techion and Origen-2 for testing Hamor-2, its results were compared to concentration values measured from activides of two PWR reactors; Kernkraftwerk Obrighein (KWO) and H.B. Robinson (HBR). These actinides are U 235 , U 236 , U 238 , Pu 239 , Pu 241 and PU 242 . The computer code Hammor-2 shows better results than the computer code Origem-2, when both are compared with experimental results. (E.G.) [pt

Monte Carlo code criticality benchmark comparisons for waste packaging

International Nuclear Information System (INIS)

Alesso, H.P.; Annese, C.E.; Buck, R.M.; Pearson, J.S.; Lloyd, W.R.

1992-07-01

COG is a new point-wise Monte Carlo code being developed and tested at Lawrence Livermore National Laboratory (LLNL). It solves the Boltzmann equation for the transport of neutrons and photons. The objective of this paper is to report on COG results for criticality benchmark experiments both on a Cray mainframe and on a HP 9000 workstation. COG has been recently ported to workstations to improve its accessibility to a wider community of users. COG has some similarities to a number of other computer codes used in the shielding and criticality community. The recently introduced high performance reduced instruction set (RISC) UNIX workstations provide computational power that approach mainframes at a fraction of the cost. A version of COG is currently being developed for the Hewlett Packard 9000/730 computer with a UNIX operating system. Subsequent porting operations will move COG to SUN, DEC, and IBM workstations. In addition, a CAD system for preparation of the geometry input for COG is being developed. In July 1977, Babcock ampersand Wilcox Co. (B ampersand W) was awarded a contract to conduct a series of critical experiments that simulated close-packed storage of LWR-type fuel. These experiments provided data for benchmarking and validating calculational methods used in predicting K-effective of nuclear fuel storage in close-packed, neutron poisoned arrays. Low enriched UO2 fuel pins in water-moderated lattices in fuel storage represent a challenging criticality calculation for Monte Carlo codes particularly when the fuel pins extend out of the water. COG and KENO calculational results of these criticality benchmark experiments are presented

SUMMARY OF GENERAL WORKING GROUP A+B+D: CODES BENCHMARKING.

Energy Technology Data Exchange (ETDEWEB)

WEI, J.; SHAPOSHNIKOVA, E.; ZIMMERMANN, F.; HOFMANN, I.

2006-05-29

Computer simulation is an indispensable tool in assisting the design, construction, and operation of accelerators. In particular, computer simulation complements analytical theories and experimental observations in understanding beam dynamics in accelerators. The ultimate function of computer simulation is to study mechanisms that limit the performance of frontier accelerators. There are four goals for the benchmarking of computer simulation codes, namely debugging, validation, comparison and verification: (1) Debugging--codes should calculate what they are supposed to calculate; (2) Validation--results generated by the codes should agree with established analytical results for specific cases; (3) Comparison--results from two sets of codes should agree with each other if the models used are the same; and (4) Verification--results from the codes should agree with experimental measurements. This is the summary of the joint session among working groups A, B, and D of the HI32006 Workshop on computer codes benchmarking.

The ENSDF Java Package

International Nuclear Information System (INIS)

Sonzogni, A.A.

2005-01-01

A package of computer codes has been developed to process and display nuclear structure and decay data stored in the ENSDF (Evaluated Nuclear Structure Data File) library. The codes were written in an object-oriented fashion using the java language. This allows for an easy implementation across multiple platforms as well as deployment on web pages. The structure of the different java classes that make up the package is discussed as well as several different implementations

ANGRA-1 neutron kinetics model at BOL using WIMSD-5B and PARCS V2.7 codes

International Nuclear Information System (INIS)

Hamers, Adolfo R.; Reis, Patricia A.L.; Rodrigues, Thiago D.A.; Pereira, Claubia; Costa, Antonella L.

2015-01-01

A steady-state neutron kinetics model of the Angra-1 NPP at BOL (Beginning Of Life) has been developed with the PARCS V2.7 neutron diffusion code. The information of the burnable poison rods, fuel enrichments and control rod banks distributions within the core have been taken from the Angra-1 FSAR (Final Safety Analysis Report) and implemented in the model. The macroscopic cross sections for the fast and thermal neutron groups have been calculated with the WIMSD-5B lattice cell code. The cross sections were obtained for the rodded and unrodded cases for each composition in the core. In order to establish the initial steady-state, an eigenvalue was made with the PARCS V2.7 code for three steady-state scenario cases reported at the FSAR; a K eff of 1.0733 was obtained for the unrodded case, K eff of 1.0718 for a 24% of bank D inserted case and K eff of 0.8512 for the full rodded case. The normalized core power density distributions were obtained and compared with the corresponding FSAR case. (author)

Solving Differential Equations in R: Package deSolve

Directory of Open Access Journals (Sweden)

Karline Soetaert

2010-02-01

Full Text Available In this paper we present the R package deSolve to solve initial value problems (IVP written as ordinary differential equations (ODE, differential algebraic equations (DAE of index 0 or 1 and partial differential equations (PDE, the latter solved using the method of lines approach. The differential equations can be represented in R code or as compiled code. In the latter case, R is used as a tool to trigger the integration and post-process the results, which facilitates model development and application, whilst the compiled code significantly increases simulation speed. The methods implemented are efficient, robust, and well documented public-domain Fortran routines. They include four integrators from the ODEPACK package (LSODE, LSODES, LSODA, LSODAR, DVODE and DASPK2.0. In addition, a suite of Runge-Kutta integrators and special-purpose solvers to efficiently integrate 1-, 2- and 3-dimensional partial differential equations are available. The routines solve both stiff and non-stiff systems, and include many options, e.g., to deal in an efficient way with the sparsity of the Jacobian matrix, or finding the root of equations. In this article, our objectives are threefold: (1 to demonstrate the potential of using R for dynamic modeling, (2 to highlight typical uses of the different methods implemented and (3 to compare the performance of models specified in R code and in compiled code for a number of test cases. These comparisons demonstrate that, if the use of loops is avoided, R code can efficiently integrate problems comprising several thousands of state variables. Nevertheless, the same problem may be solved from 2 to more than 50 times faster by using compiled code compared to an implementation using only R code. Still, amongst the benefits of R are a more flexible and interactive implementation, better readability of the code, and access to R’s high-level procedures. deSolve is the successor of package odesolve which will be deprecated in

Calculation of Single Cell and Fuel Assembly IRIS Benchmarks Using WIMSD5B and GNOMER Codes

International Nuclear Information System (INIS)

Pevec, D.; Grgic, D.; Jecmenica, R.

2002-01-01

IRIS reactor (an acronym for International Reactor Innovative and Secure) is a modular, integral, light water cooled, small to medium power (100-335 MWe/module) reactor, which addresses the requirements defined by the United States Department of Energy for Generation IV nuclear energy systems, i.e., proliferation resistance, enhanced safety, improved economics, and waste reduction. An international consortium led by Westinghouse/BNFL was created for development of IRIS reactor; it includes universities, institutes, commercial companies, and utilities. Faculty of Electrical Engineering and Computing, University of Zagreb joined the consortium in year 2001, with the aim to take part in IRIS neutronics design and safety analyses of IRIS transients. A set of neutronic benchmarks for IRIS reactor was defined with the objective to compare results of all participants with exactly the same assumptions. In this paper a calculation of Benchmark 44 for IRIS reactor is described. Benchmark 44 is defined as a core depletion benchmark problem for specified IRIS reactor operating conditions (e.g., temperatures, moderator density) without feedback. Enriched boron, inhomogeneously distributed in axial direction, is used as an integral fuel burnable absorber (IFBA). The aim of this benchmark was to enable a more direct comparison of results of different code systems. Calculations of Benchmark 44 were performed using the modified CORD-2 code package. The CORD-2 code package consists of WIMSD and GNOMER codes. WIMSD is a well-known lattice spectrum calculation code. GNOMER solves the neutron diffusion equation in three-dimensional Cartesian geometry by the Green's function nodal method. The following parameters were obtained in Benchmark 44 analysis: effective multiplication factor as a function of burnup, nuclear peaking factor as a function of burnup, axial offset as a function of burnup, core-average axial power profile, core radial power profile, axial power profile for selected

ORIGEN-ARP 2.00, Isotope Generation and Depletion Code System-Matrix Exponential Method with GUI and Graphics Capability

International Nuclear Information System (INIS)

2002-01-01

1 - Description of program or function: ORIGEN-ARP was developed for the Nuclear Regulatory Commission and the Department of Energy to satisfy a need for an easy-to-use standardized method of isotope depletion/decay analysis for spent fuel, fissile material, and radioactive material. It can be used to solve for spent fuel characterization, isotopic inventory, radiation source terms, and decay heat. This release of ORIGEN-ARP is a standalone code package that contains an updated version of the SCALE-4.4a ORIGEN-S code. It contains a subset of the modules, data libraries, and miscellaneous utilities in SCALE-4.4a. This package is intended for users who do not need the entire SCALE package. ORIGEN-ARP 2.00 (2-12-2002) differs from the previous release ORIGEN-ARP 1.0 (July 2001) in the following ways: 1.The neutron source and energy spectrum routines were replaced with computational algorithms and data from the SOURCES-4B code (RSICC package CCC-661) to provide more accurate spontaneous fission and (alpha,n) neutron sources, and a delayed neutron source capability was added. 2.The printout of the fixed energy group structure photon tables was removed. Gamma sources and spectra are now printed for calculations using the Master Photon Library only. 2 - Methods: ORIGEN-ARP is an automated sequence to perform isotopic depletion / decay calculations using the ARP and ORIGEN-S codes of the SCALE system. The sequence includes the OrigenArp for Windows graphical user interface (GUI) that prepares input for ARP (Automated Rapid Processing) and ORIGEN-S. ARP automatically interpolates cross sections for the ORIGEN-S depletion/decay analysis using enrichment, burnup, and, optionally moderator density, from a set of libraries generated with the SCALE SAS2 depletion sequence. Library sets for four LWR fuel assembly designs (BWR 8 x 8, PWR 14 x 14, 15 x 15, 17 x 17) are included. The libraries span enrichments from 1.5 to 5 wt% U-235 and burnups of 0 to 60,000 MWD/MTU. Other

Software package as an information center product

International Nuclear Information System (INIS)

Butler, M.K.

1977-01-01

The Argonne Code Center serves as a software exchange and information center for the U.S. Energy Research and Development Administration and the Nuclear Regulatory Commission. The goal of the Center's program is to provide a means for sharing of software among agency offices and contractors, and for transferring computing applications and technology, developed within the agencies, to the information-processing community. A major activity of the Code Center is the acquisition, review, testing, and maintenance of a collection of software--computer systems, applications programs, subroutines, modules, and data compilations--prepared by agency offices and contractors to meet programmatic needs. A brief review of the history of computer program libraries and software sharing is presented to place the Code Center activity in perspective. The state-of-the-art discussion starts off with an appropriate definition of the term software package, together with descriptions of recommended package contents and the Carter's package evaluation activity. An effort is made to identify the various users of the product, to enumerate their individual needs, to document the Center's efforts to meet these needs and the ongoing interaction with the user community. Desirable staff qualifications are considered, and packaging problems, reviewed. The paper closes with a brief look at recent developments and a forecast of things to come. 2 tables

49 CFR 173.3 - Packaging and exceptions.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Packaging and exceptions. 173.3 Section 173.3... SHIPMENTS AND PACKAGINGS General § 173.3 Packaging and exceptions. (a) The packaging of hazardous materials.... standard packaging must be open to inspection by a representative of the Department. (b) The regulations...

Remote-Handled Transuranic Waste Content Codes (RH-Trucon)

International Nuclear Information System (INIS)

2006-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC). The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: (1) A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. (2) A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is ''3''. The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

Mechanisms of human immunodeficiency virus type 2 RNA packaging

DEFF Research Database (Denmark)

Ni, Na; Nikolaitchik, Olga A; Dilley, Kari A

2011-01-01

do not support the cis-packaging hypothesis but instead indicate that trans packaging is the major mechanism of HIV-2 RNA packaging. To further characterize the mechanisms of HIV-2 RNA packaging, we visualized HIV-2 RNA in individual particles by using fluorescent protein-tagged RNA-binding proteins......Human immunodeficiency virus type 2 (HIV-2) has been reported to have a distinct RNA packaging mechanism, referred to as cis packaging, in which Gag proteins package the RNA from which they were translated. We examined the progeny generated from dually infected cell lines that contain two HIV-2...... proviruses, one with a wild-type gag/gag-pol and the other with a mutant gag that cannot express functional Gag/Gag-Pol. Viral titers and RNA analyses revealed that mutant viral RNAs can be packaged at efficiencies comparable to that of viral RNA from which wild-type Gag/Gag-Pol is translated. These results...

AMZ, library of multigroup constants for EXPANDA computer codes, generated by NJOY computer code from ENDF/B-IV

International Nuclear Information System (INIS)

Chalhoub, E.S.; Moraes, M. de.

1984-01-01

A 70-group, 37-isotope library of multigroup constants for fast reactor nuclear design calculations is described. Nuclear cross sections, transfer matrices, and self-shielding factors were generated with NJOY code and an auxiliary program RGENDF using evaluated data from ENDF/B-IV. The output is being issued in a format suitable for EXPANDA code. Comparisons with JFS-2 library, as well as, test resuls for 14 CSEWG benchmark critical assemblies are presented. (Author) [pt

49 CFR 178.915 - General Large Packaging standards.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false General Large Packaging standards. 178.915 Section... PACKAGINGS Large Packagings Standards § 178.915 General Large Packaging standards. (a) Each Large Packaging.... Large Packagings intended for solid hazardous materials must be sift-proof and water-resistant. (b) All...

Particle and heavy ion transport code system, PHITS, version 2.52

International Nuclear Information System (INIS)

Sato, Tatsuhiko; Matsuda, Norihiro; Hashimoto, Shintaro; Iwamoto, Yosuke; Noda, Shusaku; Ogawa, Tatsuhiko; Nakashima, Hiroshi; Fukahori, Tokio; Okumura, Keisuke; Kai, Tetsuya; Niita, Koji; Iwase, Hiroshi; Chiba, Satoshi; Furuta, Takuya; Sihver, Lembit

2013-01-01

An upgraded version of the Particle and Heavy Ion Transport code System, PHITS2.52, was developed and released to the public. The new version has been greatly improved from the previously released version, PHITS2.24, in terms of not only the code itself but also the contents of its package, such as the attached data libraries. In the new version, a higher accuracy of simulation was achieved by implementing several latest nuclear reaction models. The reliability of the simulation was improved by modifying both the algorithms for the electron-, positron-, and photon-transport simulations and the procedure for calculating the statistical uncertainties of the tally results. Estimation of the time evolution of radioactivity became feasible by incorporating the activation calculation program DCHAIN-SP into the new package. The efficiency of the simulation was also improved as a result of the implementation of shared-memory parallelization and the optimization of several time-consuming algorithms. Furthermore, a number of new user-support tools and functions that help users to intuitively and effectively perform PHITS simulations were developed and incorporated. Due to these improvements, PHITS is now a more powerful tool for particle transport simulation applicable to various research and development fields, such as nuclear technology, accelerator design, medical physics, and cosmic-ray research. (author)

Safety Analysis Report for Packaging, Y-12 National Security Complex, Model ES-3100 Package with Bulk HEU Contents

Energy Technology Data Exchange (ETDEWEB)

Anderson, James [Y-12 National Security Complex, Oak Ridge, TN (United States); Goins, Monty [Y-12 National Security Complex, Oak Ridge, TN (United States); Paul, Pran [Y-12 National Security Complex, Oak Ridge, TN (United States); Wilkinson, Alan [Y-12 National Security Complex, Oak Ridge, TN (United States); Wilson, David [Y-12 National Security Complex, Oak Ridge, TN (United States)

2015-09-03

This safety analysis report for packaging (SARP) presents the results of the safety analysis prepared in support of the Consolidated Nuclear Security, LLC (CNS) request for licensing of the Model ES-3100 package with bulk highly enriched uranium (HEU) contents and issuance of a Type B(U) Fissile Material Certificate of Compliance. This SARP, published in the format specified in the Nuclear Regulatory Commission (NRC) Regulatory Guide 7.9 and using information provided in UCID-21218 and NRC Regulatory Guide 7.10, demonstrates that the Y-12 National Security Complex (Y-12) ES-3100 package with bulk HEU contents meets the established NRC regulations for packaging, preparation for shipment, and transportation of radioactive materials given in Title 10, Part 71, of the Code of Federal Regulations (CFR) [10 CFR 71] as well as U.S. Department of Transportation (DOT) regulations for packaging and shipment of hazardous materials given in Title 49 CFR. To protect the health and safety of the public, shipments of adioactive materials are made in packaging that is designed, fabricated, assembled, tested, procured, used, maintained, and repaired in accordance with the provisions cited above. Safety requirements addressed by the regulations that must be met when transporting radioactive materials are containment of radioactive materials, radiation shielding, and assurance of nuclear subcriticality.

Research on the improvement of nuclear safety -Improvement of level 1 PSA computer code package-

International Nuclear Information System (INIS)

Park, Chang Kyoo; Kim, Tae Woon; Kim, Kil Yoo; Han, Sang Hoon; Jung, Won Dae; Jang, Seung Chul; Yang, Joon Un; Choi, Yung; Sung, Tae Yong; Son, Yung Suk; Park, Won Suk; Jung, Kwang Sub; Kang Dae Il; Park, Jin Heui; Hwang, Mi Jung; Hah, Jae Joo

1995-07-01

This year is the third year of the Government-sponsored mid- and long-term nuclear power technology development project. The scope of this sub project titled on 'The improvement of level-1 PSA computer codes' is divided into three main activities : (1) Methodology development on the underdeveloped fields such as risk assessment technology for plant shutdown and low power situations, (2) Computer code package development for level-1 PSA, (3) Applications of new technologies to reactor safety assessment. At first, in this area of shutdown risk assessment technology development, plant outage experiences of domestic plants are reviewed and plant operating states (POS) are decided. A sample core damage frequency is estimated for over draining event in RCS low water inventory i.e. mid-loop operation. Human reliability analysis and thermal hydraulic support analysis are identified to be needed to reduce uncertainty. Two design improvement alternatives are evaluated using PSA technique for mid-loop operation situation: one is use of containment spray system as backup of shutdown cooling system and the other is installation of two independent level indication system. Procedure change is identified more preferable option to hardware modification in the core damage frequency point of view. Next, level-1 PSA code KIRAP is converted to PC-windows environment. For the improvement of efficiency in performing PSA, the fast cutest generation algorithm and an analytical technique for handling logical loop in fault tree modeling are developed. 48 figs, 15 tabs, 59 refs. (Author)

Research on the improvement of nuclear safety -Improvement of level 1 PSA computer code package-

Energy Technology Data Exchange (ETDEWEB)

Park, Chang Kyoo; Kim, Tae Woon; Kim, Kil Yoo; Han, Sang Hoon; Jung, Won Dae; Jang, Seung Chul; Yang, Joon Un; Choi, Yung; Sung, Tae Yong; Son, Yung Suk; Park, Won Suk; Jung, Kwang Sub; Kang Dae Il; Park, Jin Heui; Hwang, Mi Jung; Hah, Jae Joo [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-07-01

This year is the third year of the Government-sponsored mid- and long-term nuclear power technology development project. The scope of this sub project titled on `The improvement of level-1 PSA computer codes` is divided into three main activities : (1) Methodology development on the underdeveloped fields such as risk assessment technology for plant shutdown and low power situations, (2) Computer code package development for level-1 PSA, (3) Applications of new technologies to reactor safety assessment. At first, in this area of shutdown risk assessment technology development, plant outage experiences of domestic plants are reviewed and plant operating states (POS) are decided. A sample core damage frequency is estimated for over draining event in RCS low water inventory i.e. mid-loop operation. Human reliability analysis and thermal hydraulic support analysis are identified to be needed to reduce uncertainty. Two design improvement alternatives are evaluated using PSA technique for mid-loop operation situation: one is use of containment spray system as backup of shutdown cooling system and the other is installation of two independent level indication system. Procedure change is identified more preferable option to hardware modification in the core damage frequency point of view. Next, level-1 PSA code KIRAP is converted to PC-windows environment. For the improvement of efficiency in performing PSA, the fast cutest generation algorithm and an analytical technique for handling logical loop in fault tree modeling are developed. 48 figs, 15 tabs, 59 refs. (Author).

Waste package performance assessment

International Nuclear Information System (INIS)

Lester, D.H.

1981-01-01

This paper describes work undertaken to assess the life-expectancy and post-failure nuclide release behavior of high-level and waste packages in a geologic repository. The work involved integrating models of individual phenomena (such as heat transfer, corrosion, package deformation, and nuclide transport) and using existing data to make estimates of post-emplacement behavior of waste packages. A package performance assessment code was developed to predict time to package failure in a flooded repository and subsequent transport of nuclides out of the leaking package. The model has been used to evaluate preliminary package designs. The results indicate, that within the limitation of model assumptions and data base, packages lasting a few hundreds of years could be developed. Very long lived packages may be possible but more comprehensive data are needed to confirm this

Development of waste packages for tuff

International Nuclear Information System (INIS)

Rothman, A.J.

1982-01-01

The objective of this program is to develop nuclear waste packages that meet the Nuclear Regulatory Commission's requirements for a licensed repository in tuff at the Nevada Test Site. Selected accomplishments for FY82 are: (1) Selection, collection of rock, and characterization of suitable outcrops (for lab experiments); (2) Rock-water interactions (Bullfrog Tuff); (3) Corrosion tests of ferrous metals; (4) Thermal modeling of waste package in host rock; (5) Preliminary fabrication tests of alternate backfills (crushed tuff); (6) Reviewed Westinghouse conceptual waste package designs for tuff and began modification for unsaturated zone; and (7) Waste Package Codes (BARIER and WAPPA) now running on our computer. Brief discussions are presented for rock-water interactions, corrosion tests of ferrous metals, and thermal and radionuclide migration modelling

Summary of ENDF/B pre-processing codes

International Nuclear Information System (INIS)

Cullen, D.E.

1981-12-01

This document contains the summary documentation for the ENDF/B pre-processing codes: LINEAR, RECENT, SIGMA1, GROUPIE, EVALPLOT, MERGER, DICTION, CONVERT. This summary documentation is merely a copy of the comment cards that appear at the beginning of each programme; these comment cards always reflect the latest status of input options, etc. For the latest published documentation on the methods used in these codes see UCRL-50400, Vol.17 parts A-E, Lawrence Livermore Laboratory (1979)

Type B plutonium transport package development that uses metallic filaments and composite materials

International Nuclear Information System (INIS)

Pierce, J.D.; Moya, J.L.; McClure, J.D.; Hohnstreiter, G.F.; Golliher, K.G.

1993-01-01

The objective of this program was to develop a concept for a Type B packaging that could meet present and future regulatory requirements. Two prototype packages were fabricated and subjected to dynamic crush (500 kg steel plate dropped 9 meters onto the package) environments. Subsequent evaluation indicated no deformation in the seal areas that would allow dispersal of the material. One-dimensional wall sections were fabricated to obtain thermal conductivity values for pre- and post-accident conditions. Finally, structural and thermal computer models were developed and benchmarked by test results to predict package behavior during accident environments. Design details, cost analyses, and results from structural and thermal finite element analyses are presented. In addition, the experimental results of lateral and axial dynamic crush tests, simulated fire tests, and handling tests are also discussed. (J.P.N.)

MELCOR computer code manuals

Energy Technology Data Exchange (ETDEWEB)

Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L. [Sandia National Labs., Albuquerque, NM (United States); Hodge, S.A.; Hyman, C.R.; Sanders, R.L. [Oak Ridge National Lab., TN (United States)

1995-03-01

MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR`s phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package.

MELCOR computer code manuals

International Nuclear Information System (INIS)

Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L.; Hodge, S.A.; Hyman, C.R.; Sanders, R.L.

1995-03-01

MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR's phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package

DELIGHT-B/REDEL, point reactivity burnup code for high-temperature gas-cooled reactor cells

International Nuclear Information System (INIS)

Shindo, Ryuiti; Watanabe, Takashi.

1977-03-01

Code DELIGHT-2 was previously developed to analyze cell burnup characteristics and to produce few-group constants for core burnup calculation in high-temperature gas-cooled reactors. In the code, burnup dependency of the burnable poison, boron-10, is considered with the homogeneous model of space. In actuality, however, the burnable poison is used as homogeneous rods or uniform rods of small granular poison and graphite, to control the reactivity and power distribution. Precise analysis of the burnup characteristics is thus difficult because of the heterogeneity due to the configuration of poison rods. In cell burnup calculation, the DELIGHT-B, which is a modification of DELIGHT-2, takes into consideration this heterogeneous effect. The auxiliary code REDEL, a reduction of DELIGHT-B, used in combination with 3 dimensional diffusion code CITATION, is for core burnup calculation with the macro-scopic cross section model. (auth.)

The octopus burnup and criticality code system

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, J.L.; Kuijper, J.C. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Leege, P.F.A. de

1996-09-01

The OCTOPUS burnup and criticality code system is described. This system links the spectrum codes from the SCALE4.1, WIMS7 and MCNP4A packages to the ORIGEN-S and FISPACT4.2 fuel depletion and activation codes, which enables us to perform very accurate burnup calculations in complicated three-dimensional geometries. The data used by all codes are consistently based on the JEF2.2 evaluated nuclear data file. Some special features of OCTOPUS not available in other codes are described, as well as the validation of the system. (author)

The OCTOPUS burnup and criticality code system

Energy Technology Data Exchange (ETDEWEB)

Kloosterman, J.L. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Kuijper, J.C. [Netherlands Energy Research Foundation (ECN), Petten (Netherlands); Leege, P.F.A. de [Technische Univ. Delft (Netherlands). Interfacultair Reactor Inst.

1996-06-01

The OCTOPUS burnup and criticality code system is described. This system links the spectrum codes from the SCALE4.1, WIMS7 and MCNP4A packages to the ORIGEN-S and FISPACT4.2 fuel depletion and activation codes, which enables us to perform very accurate burnup calculations in complicated three-dimensional goemetries. The data used by all codes are consistently based on the JEF2.2 evaluated nuclear data file. Some special features of OCTOPUS not available in other codes are described, as well as the validation of the system. (orig.).

The octopus burnup and criticality code system

International Nuclear Information System (INIS)

Kloosterman, J.L.; Kuijper, J.C.; Leege, P.F.A. de.

1996-01-01

The OCTOPUS burnup and criticality code system is described. This system links the spectrum codes from the SCALE4.1, WIMS7 and MCNP4A packages to the ORIGEN-S and FISPACT4.2 fuel depletion and activation codes, which enables us to perform very accurate burnup calculations in complicated three-dimensional geometries. The data used by all codes are consistently based on the JEF2.2 evaluated nuclear data file. Some special features of OCTOPUS not available in other codes are described, as well as the validation of the system. (author)

The OCTOPUS burnup and criticality code system

International Nuclear Information System (INIS)

Kloosterman, J.L.; Kuijper, J.C.; Leege, P.F.A. de

1996-06-01

The OCTOPUS burnup and criticality code system is described. This system links the spectrum codes from the SCALE4.1, WIMS7 and MCNP4A packages to the ORIGEN-S and FISPACT4.2 fuel depletion and activation codes, which enables us to perform very accurate burnup calculations in complicated three-dimensional goemetries. The data used by all codes are consistently based on the JEF2.2 evaluated nuclear data file. Some special features of OCTOPUS not available in other codes are described, as well as the validation of the system. (orig.)

Interactions between crush conditions and fire resistance for type B(U) packages less than 500 kg

International Nuclear Information System (INIS)

Huebner, H.W.; Masslowski, J.P.

1983-01-01

In the continuation of the research work by BAM and the Commissariat a l'Energie Atomique (CEA), France, a study was made of the increased risk in regard to low-probability accidents, involving small, type B packages. An evaluation was made of the increased risk when small, type B packages are involved with a low-probability accident - one that involves both crush forces and exposure to a hydrocarbon fire. 3 references, 3 figures

9 CFR 381.144 - Packaging materials.

Science.gov (United States)

2010-01-01

... to health. All packaging materials must be safe for the intended use within the meaning of section..., from the packaging supplier under whose brand name and firm name the material is marketed to the... distinguishing brand name or code designation appearing on the packaging material shipping container; must...

The CORSYS neutronics code system

International Nuclear Information System (INIS)

Caner, M.; Krumbein, A.D.; Saphier, D.; Shapira, M.

1994-01-01

The purpose of this work is to assemble a code package for LWR core physics including coupled neutronics, burnup and thermal hydraulics. The CORSYS system is built around the cell code WIMS (for group microscopic cross section calculations) and 3-dimension diffusion code CITATION (for burnup and fuel management). We are implementing such a system on an IBM RS-6000 workstation. The code was rested with a simplified model of the Zion Unit 2 PWR. (authors). 6 refs., 8 figs., 1 tabs

Watermarking spot colors in packaging

Science.gov (United States)

Reed, Alastair; Filler, TomáÅ.¡; Falkenstern, Kristyn; Bai, Yang

2015-03-01

In January 2014, Digimarc announced Digimarc® Barcode for the packaging industry to improve the check-out efficiency and customer experience for retailers. Digimarc Barcode is a machine readable code that carries the same information as a traditional Universal Product Code (UPC) and is introduced by adding a robust digital watermark to the package design. It is imperceptible to the human eye but can be read by a modern barcode scanner at the Point of Sale (POS) station. Compared to a traditional linear barcode, Digimarc Barcode covers the whole package with minimal impact on the graphic design. This significantly improves the Items per Minute (IPM) metric, which retailers use to track the checkout efficiency since it closely relates to their profitability. Increasing IPM by a few percent could lead to potential savings of millions of dollars for retailers, giving them a strong incentive to add the Digimarc Barcode to their packages. Testing performed by Digimarc showed increases in IPM of at least 33% using the Digimarc Barcode, compared to using a traditional barcode. A method of watermarking print ready image data used in the commercial packaging industry is described. A significant proportion of packages are printed using spot colors, therefore spot colors needs to be supported by an embedder for Digimarc Barcode. Digimarc Barcode supports the PANTONE spot color system, which is commonly used in the packaging industry. The Digimarc Barcode embedder allows a user to insert the UPC code in an image while minimizing perceptibility to the Human Visual System (HVS). The Digimarc Barcode is inserted in the printing ink domain, using an Adobe Photoshop plug-in as the last step before printing. Since Photoshop is an industry standard widely used by pre-press shops in the packaging industry, a Digimarc Barcode can be easily inserted and proofed.

Evolvix BEST Names for semantic reproducibility across code2brain interfaces.

Science.gov (United States)

Loewe, Laurence; Scheuer, Katherine S; Keel, Seth A; Vyas, Vaibhav; Liblit, Ben; Hanlon, Bret; Ferris, Michael C; Yin, John; Dutra, Inês; Pietsch, Anthony; Javid, Christine G; Moog, Cecilia L; Meyer, Jocelyn; Dresel, Jerdon; McLoone, Brian; Loberger, Sonya; Movaghar, Arezoo; Gilchrist-Scott, Morgaine; Sabri, Yazeed; Sescleifer, Dave; Pereda-Zorrilla, Ivan; Zietlow, Andrew; Smith, Rodrigo; Pietenpol, Samantha; Goldfinger, Jacob; Atzen, Sarah L; Freiberg, Erika; Waters, Noah P; Nusbaum, Claire; Nolan, Erik; Hotz, Alyssa; Kliman, Richard M; Mentewab, Ayalew; Fregien, Nathan; Loewe, Martha

2017-01-01

Names in programming are vital for understanding the meaning of code and big data. We define code2brain (C2B) interfaces as maps in compilers and brains between meaning and naming syntax, which help to understand executable code. While working toward an Evolvix syntax for general-purpose programming that makes accurate modeling easy for biologists, we observed how names affect C2B quality. To protect learning and coding investments, C2B interfaces require long-term backward compatibility and semantic reproducibility (accurate reproduction of computational meaning from coder-brains to reader-brains by code alone). Semantic reproducibility is often assumed until confusing synonyms degrade modeling in biology to deciphering exercises. We highlight empirical naming priorities from diverse individuals and roles of names in different modes of computing to show how naming easily becomes impossibly difficult. We present the Evolvix BEST (Brief, Explicit, Summarizing, Technical) Names concept for reducing naming priority conflicts, test it on a real challenge by naming subfolders for the Project Organization Stabilizing Tool system, and provide naming questionnaires designed to facilitate C2B debugging by improving names used as keywords in a stabilizing programming language. Our experiences inspired us to develop Evolvix using a flipped programming language design approach with some unexpected features and BEST Names at its core. © 2016 The Authors. Annals of the New York Academy of Sciences published by Wiley Periodicals, Inc. on behalf of New York Academy of Sciences.

RH-TRU Waste Content Codes (RH-Trucon)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

International Nuclear Information System (INIS)

2007-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is '3.' The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR limits based

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions LLC

2007-08-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

RH-TRU Waste Content Codes (RH-TRUCON)

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2007-05-30

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

A predictive transport modeling code for ICRF-heated tokamaks

International Nuclear Information System (INIS)

Phillips, C.K.; Hwang, D.Q.

1992-02-01

In this report, a detailed description of the physic included in the WHIST/RAZE package as well as a few illustrative examples of the capabilities of the package will be presented. An in depth analysis of ICRF heating experiments using WHIST/RAZE will be discussed in a forthcoming report. A general overview of philosophy behind the structure of the WHIST/RAZE package, a summary of the features of the WHIST code, and a description of the interface to the RAZE subroutines are presented in section 2 of this report. Details of the physics contained in the RAZE code are examined in section 3. Sample results from the package follow in section 4, with concluding remarks and a discussion of possible improvements to the package discussed in section 5

PUFF-IV, Code System to Generate Multigroup Covariance Matrices from ENDF/B-VI Uncertainty Files

International Nuclear Information System (INIS)

2007-01-01

1 - Description of program or function: The PUFF-IV code system processes ENDF/B-VI formatted nuclear cross section covariance data into multigroup covariance matrices. PUFF-IV is the newest release in this series of codes used to process ENDF uncertainty information and to generate the desired multi-group correlation matrix for the evaluation of interest. This version includes corrections and enhancements over previous versions. It is written in Fortran 90 and allows for a more modular design, thus facilitating future upgrades. PUFF-IV enhances support for resonance parameter covariance formats described in the ENDF standard and now handles almost all resonance parameter covariance information in the resolved region, with the exception of the long range covariance sub-subsections. PUFF-IV is normally used in conjunction with an AMPX master library containing group averaged cross section data. Two utility modules are included in this package to facilitate the data interface. The module SMILER allows one to use NJOY generated GENDF files containing group averaged cross section data in conjunction with PUFF-IV. The module COVCOMP allows one to compare two files written in COVERX format. 2 - Methods: Cross section and flux values on a 'super energy grid,' consisting of the union of the required energy group structure and the energy data points in the ENDF/B-V file, are interpolated from the input cross sections and fluxes. Covariance matrices are calculated for this grid and then collapsed to the required group structure. 3 - Restrictions on the complexity of the problem: PUFF-IV cannot process covariance information for energy and angular distributions of secondary particles. PUFF-IV does not process covariance information in Files 34 and 35; nor does it process covariance information in File 40. These new formats will be addressed in a future version of PUFF

User's manual for SPLPLOT-2: a computer code for data plotting and editing in conversational mode

International Nuclear Information System (INIS)

Muramatsu, Ken; Matsumoto, Kiyoshi; Kohsaka, Atsuo; Maniwa, Masaki.

1985-07-01

The computer code SPLPLOT-2 for plotting and data editing has been developed as a part of the code package: SPLPACK-1. The SPLPLOT-2 code has capabilities of both conversational and batch processings. This report describes the user's manual for SPLPLOT-2. The following improvements have been made in the SPLPLOT-2. (1) It has capabilities of both conversational and batch processings, (2) function of conversion of files from the input SPL (Standard PLotter) files to internal work files have been implemented to reduce number of time consuming access to the input SPL files, (3) user supplied subroutines can be assigned for data editing from the SPL files, (4) in addition to the two-dimensional graphs, streamline graphs, contour line graphs and bird's-eye view graphs can be drawn. (author)

Il B2B e il paradigma dei costi di transazione (B2B and the Transaction Costs Paradigm

Directory of Open Access Journals (Sweden)

Pierluigi Sabbatini

2012-04-01

Full Text Available Business to Business (B2B Internet commerce causes a significant contraction of transaction costs. According to the Coase paradigm, we would thus expect a deverticalization of the industry and broader scope for anonymous market mechanisms. In reality, such expectations are not fully borne out by the facts. When the industrial structure is concentrated the B2Bgenerally loses its independence, and is owned by the firms which most contribute to its development, e.g. the ones able to bring the liquidity to it. The B2B governance mechanism established by these firms gives hierarchical mechanisms a role which they do not usually play in extensive, anonymous markets.         JEL Codes: D23, L86Keywords: Cost, Transaction Costs, Transactions

Normal conditions of transport thermal analysis and testing of a Type B drum package

International Nuclear Information System (INIS)

Jerrell, J.W.; Alstine, M.N. van; Gromada, R.J.

1995-01-01

Increasing the content limits of radioactive material packagings can save money and increase transportation safety by decreasing the total number of shipments required to transport large quantities of material. The contents of drum packages can be limited by unacceptable containment vessel pressures and temperatures due to the thermal properties of the insulation. The purpose of this work is to understand and predict the effects of insulation properties on containment system performance. The type B shipping container used in the study is a double containment fiberboard drum package. The package is primarily used to transport uranium and plutonium metals and oxides. A normal condition of transport (NCT) thermal test was performed to benchmark an NCT analysis of the package. A 21 W heater was placed in an instrumented package to simulate the maximum source decay heat. The package reached thermal equilibrium 120 hours after the heater was turned on. Testing took place indoors to minimize ambient temperature fluctuations. The thermal analysis of the package used fiberboard properties reported in the literature and resulted in temperature significantly greater than those measured during the test. Details of the NCT test will be described and transient temperatures at key thermocouple locations within the package will be presented. Analytical results using nominal fiberboard properties will be presented. Explanations of the results and the attempt to benchmark the analysis will be presented. The discovery that fiberboard has an anisotropic thermal conductivity and its effect on thermal performance will also be discussed

Coarse Grained Transport Model for Neutrals in Turbulent SOL Plasmas

Energy Technology Data Exchange (ETDEWEB)

Marandet, Y.; Mekkaoui, A.; Genesio, P.; Rosato, J.; Capes, H.; Godbert-Mouret, L.; Koubiti, M.; Stamm, R., E-mail: yannick.marandet@univ-amu.fr [PIIM, CNRS/Aix-Marseille University, Marseille (France); Reiter, D.; Boerner, P. [IEK4, FZJ, Juelich (Germany)

2012-09-15

Full text: Edge plasmas of magnetic fusion devices exhibit strong intermittent turbulence, which governs perpendicular transport of particles and heat. Turbulent fluxes result from the coarse graining procedure used to derive the transport equation, which entails time averaging of the underlying equations governing the turbulent evolution of the electron and ion fluids. In previous works, we have pointed out that this averaging is not carried out on the Boltzmann equation that describes the transport of neutral particles (atoms, molecules) in current edge code suites (such as SOLPS). Since fluctuations in the far SOL are of order unity, calculating the transport of neutral particles, hence the source terms in plasma fluid equations, in the average plasma background might lead to misleading results. In particular, retaining the effects of fluctuations could affect the estimation of the importance of main chamber recycling, hence first wall sputtering by charge exchange atoms, as well as main chamber impurity contamination and transport. In this contribution, we obtain an exact coarse-grained equation for the average neutral density, assuming that density fluctuations are described by multivariate Gamma statistics. This equation is a scattering free Boltzmann equation, where the ionization rate has been renormalized to account for fluctuations. The coarse grained transport model for neutrals has been implemented in the EIRENE code, and applications in 2D geometry with ITER relevant plasma parameters are presented. Our results open the way for the implementation of the effects of turbulent fluctuations on the transport of neutral particles in coupled plasma/neutral edge codes like B2-EIRENE. (author)

RH Packaging Operations Manual

International Nuclear Information System (INIS)

Washington TRU Solutions LLC

2003-01-01

This procedure provides operating instructions for the RH-TRU 72-B Road Cask, Waste Shipping Package. In this document, ''Packaging'' refers to the assembly of components necessary to ensure compliance with the packaging requirements (not loaded with a payload). ''Package'' refers to a Type B packaging that, with its radioactive contents, is designed to retain the integrity of its containment and shielding when subject to the normal conditions of transport and hypothetical accident test conditions set forth in 10 CFR Part 71. Loading of the RH 72-B cask can be done two ways, on the RH cask trailer in the vertical position or by removing the cask from the trailer and loading it in a facility designed for remote-handling (RH). Before loading the 72-B cask, loading procedures and changes to the loading procedures for the 72-B cask must be sent to CBFO at sitedocuments at wipp.ws for approval

Nanotechnology for the Solid Waste Reduction of Military Food Packaging

Science.gov (United States)

2016-06-01

WP-200816) Nanotechnology for the Solid Waste Reduction of Military Food Packaging June 2016 This document has been cleared for public release...NAME OF RESPONSIBLE PERSON 19b. TELEPHONE NUMBER (Include area code) 01/06/2016 Cost and Performance Report 04/01/2008 - 01/01/2015 Nanotechnology for...Soldier Research, Development and Engineering Center Robin Altmeyer - AmeriQual U.S. Army Natick Soldier Research, Development and Engineering

An Object-Oriented Serial DSMC Simulation Package

Science.gov (United States)

Liu, Hongli; Cai, Chunpei

2011-05-01

A newly developed three-dimensional direct simulation Monte Carlo (DSMC) simulation package, named GRASP ("Generalized Rarefied gAs Simulation Package"), is reported in this paper. This package utilizes the concept of simulation engine, many C++ features and software design patterns. The package has an open architecture which can benefit further development and maintenance of the code. In order to reduce the engineering time for three-dimensional models, a hybrid grid scheme, combined with a flexible data structure compiled by C++ language, are implemented in this package. This scheme utilizes a local data structure based on the computational cell to achieve high performance on workstation processors. This data structure allows the DSMC algorithm to be very efficiently parallelized with domain decomposition and it provides much flexibility in terms of grid types. This package can utilize traditional structured, unstructured or hybrid grids within the framework of a single code to model arbitrarily complex geometries and to simulate rarefied gas flows. Benchmark test cases indicate that this package has satisfactory accuracy for complex rarefied gas flows.

Use of computer codes for system reliability analysis

International Nuclear Information System (INIS)

Sabek, M.; Gaafar, M.; Poucet, A.

1988-01-01

This paper gives a collective summary of the studies performed at the JRC, ISPRA on the use of computer codes for complex systems analysis. The computer codes dealt with are: CAFTS-SALP software package, FRANTIC, FTAP, computer code package RALLY, and BOUNDS codes. Two reference study cases were executed by each code. The results obtained logic/probabilistic analysis as well as computation time are compared

Recent extensions and use of the statistical model code EMPIRE-II - version: 2.17 Millesimo

International Nuclear Information System (INIS)

Herman, M.

2003-01-01

This lecture notes describe new features of the modular code EMPIRE-2.17 designed to perform comprehensive calculations of nuclear reactions using variety of nuclear reaction models. Compared to the version 2.13, the current release has been extended by including Coupled-Channel mechanism, exciton model, Monte Carlo approach to preequilibrium emission, use of microscopic level densities, widths fluctuation correction, detailed calculation of the recoil spectra, and powerful plotting capabilities provided by the ZVView package. The second part of this lecture concentrates on the use of the code in practical calculations, with emphasis on the aspects relevant to nuclear data evaluation. In particular, adjusting model parameters is discussed in details. (author)

Turbulent Simulations of Divertor Detachment Based On BOUT + + Framework

Science.gov (United States)

Chen, Bin; Xu, Xueqiao; Xia, Tianyang; Ye, Minyou

2015-11-01

China Fusion Engineering Testing Reactor is under conceptual design, acting as a bridge between ITER and DEMO. The detached divertor operation offers great promise for a reduction of heat flux onto divertor target plates for acceptable erosion. Therefore, a density scan is performed via an increase of D2 gas puffing rates in the range of 0 . 0 ~ 5 . 0 ×1023s-1 by using the B2-Eirene/SOLPS 5.0 code package to study the heat flux control and impurity screening property. As the density increases, it shows a gradually change of the divertor operation status, from low-recycling regime to high-recycling regime and finally to detachment. Significant radiation loss inside the confined plasma in the divertor region during detachment leads to strong parallel density and temperature gradients. Based on the SOLPS simulations, BOUT + + simulations will be presented to investigate the stability and turbulent transport under divertor plasma detachment, particularly the strong parallel gradient driven instabilities and enhanced plasma turbulence to spread heat flux over larger surface areas. The correlation between outer mid-plane and divertor turbulence and the related transport will be analyzed. Prepared by LLNL under Contract DE-AC52-07NA27344. LLNL-ABS-675075.

Evaluation of radiation packages type A from the center of isotopes in Cuba

International Nuclear Information System (INIS)

Balbona, Zayda Amador; Pijuan, Saul Perez; Gual, Maritza Rodriguez

2013-01-01

The Isotope Center (CENTIS) of the Republic of Cuba makes the transportation of its products mainly in packaged type A. To undertake the design of packages, packaging components from 6 producing firms (including those found Amersham, CISBIO and IZOTOP) are studied. From the applicable regulations, security features and requirements are established as well as the technical characteristics of the packaging components. This study evaluated according each radioisotope, product and specific activity, high activity that can be included in a Type A package with the limitation that the dose rate on their surfaces is less than or equal to 2 mSv/h. In addition, each package is characterized taking into account the value of the maximum dose rate at maximum contact and the transport index for the day of transport. For this, the Microshield code using version 5.0.3. The dose rate in contact with the package of 90 Y is calculated using the Monte Carlo code MCNPX version 2.6.0. The maximum possible activity values are obtained for each shielding transport radionuclides CENTIS produced, namely 131 I, 125 I, 32 P, 99 Mo/ 99m Tc, 99m Tc, 188 Re and 90 Y and 69 radioactive packages type A are evaluated

Packaging- and transportation-related occurrence reports: 1993 annual report

International Nuclear Information System (INIS)

Welch, M.J.; Dickerson, L.S.; Jennings, S.D.

1994-06-01

The US Department of Energy (DOE) Occurrence Reporting and Processing System (ORPS) is an interactive computer system designed to support DOE-owned or -operated facilities in reporting and processing of information concerning occurrences related to facility operations. The requirements for reporting and the extent of the occurrences to be reported are defined in DOE Order 5000.3B, Occurrence Reporting and Processing of Operations Information (hereafter referred to as DOE 5000.3B). The centralized data base, which is managed by the Idaho National Engineering Laboratory (INEL), provides computerized support for the collection, distribution, updating, analysis, and sign-off of information in the occurrence reports (ORs). The Oak Ridge National Laboratory (ORNL) Packaging and Transportation Safety (PATS) Program has been made responsible for retrieving reports and information pertaining to transportation and packaging incidents/accidents from the centralized ORPS data base. This annual report details the methodology that PATS uses to conduct searches of the ORPS for pertinent information, the form of the reporting to EH-332, review and examination of trends observed in ORs related to transportation and packaging safety, a presentation and discussion of the root-cause codes of ORPS and the nature of occurrence codes of PATS, timely processing of notification reports to final stage, and analysis of 10% of the reported ORs that were finalized to determine whether the actions taken to close out the occurrences were sufficient to ensure remediation of the incident and to prevent a recurrence. Data in the report are presented by calendar years

Radcalc: A computer program to calculate the radiolytic production of hydrogen gas from radioactive wastes in packages

International Nuclear Information System (INIS)

Green, J.R.; Schwarz, R.A.; Hillesland, K.E.; Roetman, V.E.; Field, J.G.

1995-11-01

Radcalc for Windows' is a menu-driven Microsoft2 Windows-compatible computer code that calculates the radiolytic production of hydrogen gas in high- and low-level radioactive waste. In addition, the code also determines US Department of Transportation (DOT) transportation classifications, calculates the activities of parent and daughter isotopes for a specified period of time, calculates decay heat, and calculates pressure buildup from the production of hydrogen gas in a given package geometry. Radcalc for Windows was developed by Packaging Engineering, Transportation and Packaging, Westinghouse Hanford Company, Richland, Washington, for the US Department of Energy (DOE). It is available from Packaging Engineering and is issued with a user's manual and a technical manual. The code has been verified and validated

AMZ, multigroup constant library for EXPANDA code, generated by NJOY code from ENDF/B-IV

International Nuclear Information System (INIS)

Chalhoub, E.S.; Moraes, Marisa de

1985-01-01

It is described a library of multigroup constants with 70 energy groups and 37 isotopes to fast reactor calculation. The cross sections, scattering matrices and self-shielding factors were generated by NJOY code and RGENDF interface program, from ENDF/B-IV'S evaluated data. The library is edited in adequated format to be used by EXPANDA code. (M.C.K.) [pt

Simulation of the burnup in cell calculation using the WIMSD-5B Code considering different nuclear data libraries

International Nuclear Information System (INIS)

Tavares, Desirée Yael de Sena; Silva, Adilson Costa da; Lima, Zelmo Rodrigues de

2017-01-01

This work proposes to implement the cell calculation considering the fuel burning using the WIMSD-5B code. The cell calculation procedure allows to determine the nuclear parameters present in the multi-group neutron diffusion equation and for this purpose the neutron transport theory is used in a problem with dimensional reduction, but in contrast is considered a large number of groups associated with the neutron spectrum. There are a variety of reactor physics codes that determine the nuclear parameters by solving the neutron transport equation applied to an equivalent cell representing a fuel element. The WIMSD-5B code is a deterministic code that solves the transport equation using collision probability method. The simulation of fuel burning in the cell calculation took into account different nuclear data libraries. The WIMSD-5B code supports several nuclear data libraries and in the present work the following libraries were used: IAEA, ENDFB-VII.1, JENDL3.2, JEFF3.1 and JEF2.2, all formatted for 69 energy groups. (author)

Simulation of the burnup in cell calculation using the WIMSD-5B Code considering different nuclear data libraries

Energy Technology Data Exchange (ETDEWEB)

Tavares, Desirée Yael de Sena; Silva, Adilson Costa da; Lima, Zelmo Rodrigues de, E-mail: zelmolima@yahoo.com.br [Instituto de Engenharia Nuclear (IEN/CNEN-RJ), Rio de Janeiro, RJ (Brazil)

2017-07-01

This work proposes to implement the cell calculation considering the fuel burning using the WIMSD-5B code. The cell calculation procedure allows to determine the nuclear parameters present in the multi-group neutron diffusion equation and for this purpose the neutron transport theory is used in a problem with dimensional reduction, but in contrast is considered a large number of groups associated with the neutron spectrum. There are a variety of reactor physics codes that determine the nuclear parameters by solving the neutron transport equation applied to an equivalent cell representing a fuel element. The WIMSD-5B code is a deterministic code that solves the transport equation using collision probability method. The simulation of fuel burning in the cell calculation took into account different nuclear data libraries. The WIMSD-5B code supports several nuclear data libraries and in the present work the following libraries were used: IAEA, ENDFB-VII.1, JENDL3.2, JEFF3.1 and JEF2.2, all formatted for 69 energy groups. (author)

CIRCE2/DEKGEN2: A software package for facilitated optical analysis of 3-D distributed solar energy concentrators. Theory and user manual

Energy Technology Data Exchange (ETDEWEB)

Romero, V.J.

1994-03-01

CIRCE2 is a computer code for modeling the optical performance of three-dimensional dish-type solar energy concentrators. Statistical methods are used to evaluate the directional distribution of reflected rays from any given point on the concentrator. Given concentrator and receiver geometries, sunshape (angular distribution of incident rays from the sun), and concentrator imperfections such as surface roughness and random deviation in slope, the code predicts the flux distribution and total power incident upon the target. Great freedom exists in the variety of concentrator and receiver configurations that can be modeled. Additionally, provisions for shading and receiver aperturing are included.- DEKGEN2 is a preprocessor designed to facilitate input of geometry, error distributions, and sun models. This manual describes the optical model, user inputs, code outputs, and operation of the software package. A user tutorial is included in which several collectors are built and analyzed in step-by-step examples.

Code-B-1 for stress/strain calculation for TRISO fuel particle (Contract research)

International Nuclear Information System (INIS)

Aihara, Jun; Ueta, Shohei; Shibata, Taiju; Sawa, Kazuhiro

2011-12-01

We have developed Code-B-1 for the prediction of the failure probabilities of the coated fuel particles for the high temperature gas-cooled reactors (HTGRs) under operation by modification of an existing code. A finite element method (FEM) is employed for the stress calculation part and Code-B-1 can treat the plastic deformation of the coating layer of the coated fuel particles which the existing code cannot treat. (author)

Technical committee on transport package test standards, Tokyo, Japan, 28 September - 2 October 1981

International Nuclear Information System (INIS)

Ek, P.

The Technical Committee looked into the following tasks: a) the additional 200 m water immersion test for packages designed for irradiated fuel when the activity exceeds 10 6 Ci; b) the proposed addition of a crush test for light weight Type B and fissile materials packages; c) the proposed new text for thermal test

45 CFR Appendix B to Part 73 - Code of Ethics for Government Service

Science.gov (United States)

2010-10-01

... 45 Public Welfare 1 2010-10-01 2010-10-01 false Code of Ethics for Government Service B Appendix B to Part 73 Public Welfare DEPARTMENT OF HEALTH AND HUMAN SERVICES GENERAL ADMINISTRATION STANDARDS OF CONDUCT Pt. 73, App. B Appendix B to Part 73—Code of Ethics for Government Service Any person in...

Type B Package Radioactive Material Contents Compliance

International Nuclear Information System (INIS)

HENSEL, STEVE

2006-01-01

Implementation of packaging and transportation requirements can be subdivided into three categories; contents compliance, packaging closure, and transportation or logistical compliance. This paper addresses the area of contents compliance within the context of regulations, DOE Orders, and appropriate standards. Common practices and current pitfalls are also discussed

Code of Practice on radiation protection in the mining and milling of radioactive ores (1980) - Guidelines for storage and packaging of uranium concentrates

International Nuclear Information System (INIS)

1986-01-01

This Guideline is intended to provide assistance in the application of the 1980 Code of Practice on radiation protection in mining and milling of radioactive ores. Its purpose is to give advice relevant to the design, construction and operation of an uranium concentrate storage and packaging facility in which exposure to ionizing radiation from uranium-bearing concentrate will not only conform to the Code, but will also be as low as reasonably achievable. (NEA) [fr

Safety analysis report for packaging (onsite) Castor GSF cask

International Nuclear Information System (INIS)

Clements, E.P.

1997-01-01

The CASTOR GSF packaging was designed and fabricated to be a certified Type B(U) packaging and comply with the requirements of the International Atomic Energy Agency (IAEA) for transport of up to five sealed canisters of vitrified radioactive materials. This onsite Safety Analysis Report for Packaging (SARP) provides the analysis and evaluations necessary to demonstrate that the casks, with the canister payload, meet the intent of the Type B packaging regulations set forth in 10 CFR 71 and therefore meet the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping

Quantum Codes From Cyclic Codes Over The Ring R 2

International Nuclear Information System (INIS)

Altinel, Alev; Güzeltepe, Murat

2016-01-01

Let R 2 denotes the ring F 2 + μF 2 + υ 2 + μυ F 2 + wF 2 + μwF 2 + υwF 2 + μυwF 2 . In this study, we construct quantum codes from cyclic codes over the ring R 2 , for arbitrary length n, with the restrictions μ 2 = 0, υ 2 = 0, w 2 = 0, μυ = υμ, μw = wμ, υw = wυ and μ (υw) = (μυ) w. Also, we give a necessary and sufficient condition for cyclic codes over R 2 that contains its dual. As a final point, we obtain the parameters of quantum error-correcting codes from cyclic codes over R 2 and we give an example of quantum error-correcting codes form cyclic codes over R 2 . (paper)

Safety Analysis Report - Packages, 9965, 9968, 9972-9975 Packages

International Nuclear Information System (INIS)

Blanton, P.

2000-01-01

This Safety Analysis Report for Packaging (SARP) documents the analysis and testing performed on four type B Packages: the 9972, 9973, 9974, and 9975 packages. Because all four packages have similar designs with very similar performance characteristics, all of them are presented in a single SARP. The performance evaluation presented in this SARP documents the compliance of the 9975 package with the regulatory safety requirements. Evaluations of the 9972, 9973, and 9974 packages support that of the 9975. To avoid confusion arising from the inclusion of four packages in a single document, the text segregates the data for each package in such a way that the reader interested in only one package can progress from Chapter 1 through Chapter 9. The directory at the beginning of each chapter identifies each section that should be read for a given package. Sections marked ''all'' are generic to all packages

Milagro Version 2 An Implicit Monte Carlo Code for Thermal Radiative Transfer: Capabilities, Development, and Usage

Energy Technology Data Exchange (ETDEWEB)

T.J. Urbatsch; T.M. Evans

2006-02-15

We have released Version 2 of Milagro, an object-oriented, C++ code that performs radiative transfer using Fleck and Cummings' Implicit Monte Carlo method. Milagro, a part of the Jayenne program, is a stand-alone driver code used as a methods research vehicle and to verify its underlying classes. These underlying classes are used to construct Implicit Monte Carlo packages for external customers. Milagro-2 represents a design overhaul that allows better parallelism and extensibility. New features in Milagro-2 include verified momentum deposition, restart capability, graphics capability, exact energy conservation, and improved load balancing and parallel efficiency. A users' guide also describes how to configure, make, and run Milagro2.

FPFPspace2: A code for following airborne fission products in generic nuclear plant flow paths

International Nuclear Information System (INIS)

Owcarski, P.C.; Burk, K.W.; Ramsdell, J.V.; Yasuda, D.D.

1991-03-01

In order to assure that a nuclear power plant control room remains habitable during certain types of postulated accidents, Pacific Northwest Laboratory (PNL) has undertaken a special study for the US Nuclear Regulatory Commission. This purpose of this study is to develop software that can aid in the analyses of control room habitability during accidents in which airborne fission products could challenge internal air pathways to the control room. PNL has completed an initial version (FPFP) and final version (FPFP 2) of a software package that can estimate the unsteady-state invasion of quantities of fission products into the control room or any other destination within the nuclear plant via generic internal flow paths. This report consists of three parts: Section 2.0, Technical Bases, describes the flow path components and mechanisms of natural fission product deposition; Section 3.0, FPFP 2 Code Description, describes code organization and the functions of the subroutines; and Section 4.0, Code Operation, discusses details of input requirements, code output, and a sample case demonstration. The appendices consist of an FPFP 2 Fortran code listing, a listing of a code for building input files, forms for building input files, and the sample case input and output files. 7 refs., 3 figs

ENDF utility codes version 6.8

International Nuclear Information System (INIS)

McLaughlin, P.K.

1992-01-01

Description and operating instructions are given for a package of utility codes operating on evaluated nuclear data files in the formats ENDF-5 and ENDF-6. Included are the data checking codes CHECKER, FIZCON, PSYCHE; the code INTER for retrieving thermal cross-sections and some other data; graphical plotting codes PLOTEF, GRALIB, graphic device interface subroutine library INTLIB; and the file maintenance and retrieval codes LISTEF, SETMDC, GETMAT, STANEF. This program package which is designed for CDC, IBM, DEC and PC computers, can be obtained on magnetic tape or floppy diskette, free of charge, from the IAEA Nuclear Data Section. (author)

Implementation of the KASKAD computer code system for WWER-440 at Kozloduy NPP

International Nuclear Information System (INIS)

Antonov, A.; Georgieva, N.; Spasova, V.

2003-01-01

Since 2002 at Kozloduy NPP - EP1 the code package KASKAD is used for WWER-440 reactor core calculations. The main codes entering this package are: BIPR-7A: 3-D diffusion and core analysis code; PERMAK-A: 2-D fine mesh diffusion code. The burnup calculations were performed for all cycles of the Kozloduy NPP Unit 1, Unit 2, Unit 3 and Unit 4. For the last 4-5 cycles of the Units were calculated control rods worth, critical boron concentration at zero power, reactivity coefficients and linear power. These results were analysed and were compared with experimental data. Some results were given in this paper

49 CFR 178.935 - Standards for wooden Large Packagings.

Science.gov (United States)

2010-10-01

... Packagings. (i) Natural wood used in the construction of Large Packagings must be well-seasoned, commercially...) Reconstituted wood used in the construction of Large Packagings must be water resistant reconstituted wood such... Packaging types are designated: (1) 50C natural wood. (2) 50D plywood. (3) 50F reconstituted wood. (b...

Impact testing and analysis for structural code benchmarking

International Nuclear Information System (INIS)

Glass, R.E.

1989-01-01

Sandia National Laboratories, in cooperation with industry and other national laboratories, has been benchmarking computer codes (''Structural Code Benchmarking for the Analysis of Impact Response of Nuclear Material Shipping Cask,'' R.E. Glass, Sandia National Laboratories, 1985; ''Sample Problem Manual for Benchmarking of Cask Analysis Codes,'' R.E. Glass, Sandia National Laboratories, 1988; ''Standard Thermal Problem Set for the Evaluation of Heat Transfer Codes Used in the Assessment of Transportation Packages, R.E. Glass, et al., Sandia National Laboratories, 1988) used to predict the structural, thermal, criticality, and shielding behavior of radioactive materials packages. The first step in the benchmarking of the codes was to develop standard problem sets and to compare the results from several codes and users. This step for structural analysis codes has been completed as described in ''Structural Code Benchmarking for the Analysis of Impact Response of Nuclear Material Shipping Casks,'' R.E. Glass, Sandia National Laboratories, 1985. The problem set is shown in Fig. 1. This problem set exercised the ability of the codes to predict the response to end (axisymmetric) and side (plane strain) impacts with both elastic and elastic/plastic materials. The results from these problems showed that there is good agreement in predicting elastic response. Significant differences occurred in predicting strains for the elastic/plastic models. An example of the variation in predicting plastic behavior is given, which shows the hoop strain as a function of time at the impacting end of Model B. These differences in predicting plastic strains demonstrated a need for benchmark data for a cask-like problem. 6 refs., 5 figs

SMOG 2: A Versatile Software Package for Generating Structure-Based Models.

Science.gov (United States)

Noel, Jeffrey K; Levi, Mariana; Raghunathan, Mohit; Lammert, Heiko; Hayes, Ryan L; Onuchic, José N; Whitford, Paul C

2016-03-01

Molecular dynamics simulations with coarse-grained or simplified Hamiltonians have proven to be an effective means of capturing the functionally important long-time and large-length scale motions of proteins and RNAs. Originally developed in the context of protein folding, structure-based models (SBMs) have since been extended to probe a diverse range of biomolecular processes, spanning from protein and RNA folding to functional transitions in molecular machines. The hallmark feature of a structure-based model is that part, or all, of the potential energy function is defined by a known structure. Within this general class of models, there exist many possible variations in resolution and energetic composition. SMOG 2 is a downloadable software package that reads user-designated structural information and user-defined energy definitions, in order to produce the files necessary to use SBMs with high performance molecular dynamics packages: GROMACS and NAMD. SMOG 2 is bundled with XML-formatted template files that define commonly used SBMs, and it can process template files that are altered according to the needs of each user. This computational infrastructure also allows for experimental or bioinformatics-derived restraints or novel structural features to be included, e.g. novel ligands, prosthetic groups and post-translational/transcriptional modifications. The code and user guide can be downloaded at http://smog-server.org/smog2.

SMOG 2: A Versatile Software Package for Generating Structure-Based Models.

Directory of Open Access Journals (Sweden)

Jeffrey K Noel

2016-03-01

Full Text Available Molecular dynamics simulations with coarse-grained or simplified Hamiltonians have proven to be an effective means of capturing the functionally important long-time and large-length scale motions of proteins and RNAs. Originally developed in the context of protein folding, structure-based models (SBMs have since been extended to probe a diverse range of biomolecular processes, spanning from protein and RNA folding to functional transitions in molecular machines. The hallmark feature of a structure-based model is that part, or all, of the potential energy function is defined by a known structure. Within this general class of models, there exist many possible variations in resolution and energetic composition. SMOG 2 is a downloadable software package that reads user-designated structural information and user-defined energy definitions, in order to produce the files necessary to use SBMs with high performance molecular dynamics packages: GROMACS and NAMD. SMOG 2 is bundled with XML-formatted template files that define commonly used SBMs, and it can process template files that are altered according to the needs of each user. This computational infrastructure also allows for experimental or bioinformatics-derived restraints or novel structural features to be included, e.g. novel ligands, prosthetic groups and post-translational/transcriptional modifications. The code and user guide can be downloaded at http://smog-server.org/smog2.

Customization of the GENFIT2 Fitting Package in P̅ANDA

Directory of Open Access Journals (Sweden)

Prencipe Elisabetta

2016-01-01

Full Text Available The availability of a cooled antiproton beam in the energy range from 2.0 to 5.5 GeV will allow the P̅ANDA experiment, planned for operation in FAIR (Darmstadt, Germany, to perform a wide nuclear and particle physics program. P̅ANDA is the only experiment worldwide in that energy regime that combines a solenoidal magnetic field (B = 2 T and a dipole field (maximum bending power equal to 2 Tm in a fixed-target experiment. The offline tracking algorithm is developed within the PandaRoot framework, which is part of the FairRoot project. Here the GENFIT2 package is presented. The tool contains an implementation of the Kalman filter and the deterministic annealing filter for charged particle track reconstruction, together with a Runge-Kutta track representation. It also interfaces with Millipede II and RAVE, for alignment and vertex reconstruction, respectively. The performance of this track-fitting package for the P̅ANDA experiment is shown for the first time, within the PandaRoot framework. For those channels where a good low momentum tracking is required, i.e. pT <350 MeV/c, an improvement by a factor of about two is shown.

London 2012 packaging guidelines

OpenAIRE

2013-01-01

These guidelines are intended to provide supplemental advice to suppliers and licensees regarding the provisions of the LOCOG Sustainable Sourcing Code that relate to packaging design and materials selection.

Progress in waste package and engineered barrier system performance assessment and design

International Nuclear Information System (INIS)

Van Luik, A.; Stahl, D.; Harrison, D.

1993-01-01

As part of the U.S. Department of Energy's evaluation of site suitability for a potential high-level radioactive waste repository, long-term interactions between the engineered barrier system and the site must be determined. This requires a waste-package/engineered-system design, a description of the environment around the emplacement zone, and models that simulate operative processes describing these engineered/natural systems interactions. Candidate designs are being evaluated, including a more robust, multi-barrier waste package, and a drift emplacement mode. Tools for evaluating designs, and emplacement mode are the currently available waste-package/engineered-system performance assessment codes development for the project. For assessments that support site suitability, environmental impact, or licensing decisions, more capable codes are needed. Code capability requirements are being written, and existing codes are to be evaluated against those requirements. Recommendations are being made to focus waste-packaging/engineered-system code-development

Tourist Affiliate Program while Using Online Booking System with Possibility of Entering B2B Code

Directory of Open Access Journals (Sweden)

Slivar Iva

2008-01-01

Full Text Available Affiliate marketing programs are one of the most powerful tools for online marketing since the merchant presenting a product or a service decides on the commissioning model and the commission is granted only if the desired results have been reached. Affiliate marketing is based offline as much as tourism itself and it relies on the commission that tourist companies pay to their partners (affiliates who bring new guests. This paper will present the basics of how online affiliate programs work, benefits they bring and steps for their further implementation. It will explain in detail how to establish an affiliate program for dynamic web pages which use online booking system platforms that offer a possibility of entering a B2B code. Special attention will be paid to SEO (Search Engine Optimisation. It will also present results of a research on Croatian hotels web pages and the implementation of the online booking system and affiliate programs. Having in mind the insufficient deployment of online potentials, the aim of the paper is to stress the need for setting up an effective method of monitoring changes and updates in the online world as well as implementing new promotional possibilities, all aimed at increasing sales. The goal of the paper is to explore advantages and disadvantages of the affiliate program as a new sales channel and promote the possibility to implement it in one of the biggest Croatian hotel companies, Maistra d.d. Rovinj. Along with methods of data acquiring and different techniques of creative thinking, the following scientific research methods were also used: statistic, historic, descriptive, comparison, interview, analysis and synthesis, induction and deduction.

INTRA graphical package - INTRA-Graph 1.0

International Nuclear Information System (INIS)

Hofman, D.; Edlund, O.

2001-04-01

INTRA-Graph 1.0 has been developed at Studsvik Eco and Safety AB in the frame of the European Fusion Technology Programme for application in the safety analysis using the INTRA code. INTRA-Graph 1.0 is a graphical package producing 2-dimensional plots of results generated by the INTRA code. INTRA-Graph 1.0 has been developed by extending the Grace package source code, distributed under the terms of GNU General Public License. The changes in the Grace source files are limited to provide easy updates of the INTRA-Graph when a new version of Grace will be released. The INTRA-related functionality has been implemented in new source files. The present report describes and gives complete listing of these files. The changes in the Grace source files are also described and the listing of the changed parts of the files is presented. The report gives detailed explanations and examples of files required for installation and configuration of INTRA-Graph on the different types of Unix workstations

NORTICA - a new code for cyclotron analysis

International Nuclear Information System (INIS)

Gorelov, D.; Johnson, D.; Marti, F.

2001-01-01

The new package NORTICA (Numerical ORbit Tracking In Cyclotrons with Analysis) of computer codes for beam dynamics simulations is under development at NSCL. The package was started as a replacement for the code MONSTER developed in the laboratory in the past. The new codes are capable of beam dynamics simulations in both CCF (Coupled Cyclotron Facility) accelerators, the K500 and K1200 superconducting cyclotrons. The general purpose of this package is assisting in setting and tuning the cyclotrons taking into account the main field and extraction channel imperfections. The computer platform for the package is Alpha Station with UNIX operating system and X-Windows graphic interface. A multiple programming language approach was used in order to combine the reliability of the numerical algorithms developed over the long period of time in the laboratory and the friendliness of modern style user interface. This paper describes the capability and features of the codes in the present state

NORTICA—a new code for cyclotron analysis

Science.gov (United States)

Gorelov, D.; Johnson, D.; Marti, F.

2001-12-01

The new package NORTICA (Numerical ORbit Tracking In Cyclotrons with Analysis) of computer codes for beam dynamics simulations is under development at NSCL. The package was started as a replacement for the code MONSTER [1] developed in the laboratory in the past. The new codes are capable of beam dynamics simulations in both CCF (Coupled Cyclotron Facility) accelerators, the K500 and K1200 superconducting cyclotrons. The general purpose of this package is assisting in setting and tuning the cyclotrons taking into account the main field and extraction channel imperfections. The computer platform for the package is Alpha Station with UNIX operating system and X-Windows graphic interface. A multiple programming language approach was used in order to combine the reliability of the numerical algorithms developed over the long period of time in the laboratory and the friendliness of modern style user interface. This paper describes the capability and features of the codes in the present state.

User's guide for shipping Type B quantities of radioactive and fissile material, including plutonium, in DOT-6M specification packaging configurations

International Nuclear Information System (INIS)

Kelly, D.L.

1994-09-01

The need for developing a user's guide for shipping Type B quantities of radioactive and fissile material, including plutonium, in a US Department of Transportation Specification 6M (DOT-6M) packaging was identified by the US Department of Energy (DOE)-Headquarters, Transportation Management Division (EM-261) because the DOT-6M packaging is widely used by DOE site contractors and the DOE receives many questions about approved packaging configuration. Currently, EM-261 has the authority to approve new DOT-6M packaging configurations for use by the DOE Operations Offices. This user's guide identifies the DOE-approved DOT-6M packaging configurations and explains how to have new configurations approved by the DOE. The packaging configurations described in this guide are approved by the DOE, and satisfy the applicable DOT requirements and the identified DOE restrictions. These packaging configurations are acceptable for transport of Type B quantities of radioactive and fissile material, including plutonium

49 CFR 178.940 - Standards for flexible Large Packagings.

Science.gov (United States)

2010-10-01

.... Flexible Large Packagings types are designated: (1) 51H flexible plastics. (2) 51M flexible paper. (b... this subchapter, flexible Large Packaging must be resistant to aging and degradation caused by ultraviolet radiation. (5) For plastic flexible Large Packagings, if necessary, protection against ultraviolet...

Modular assembly of chimeric phi29 packaging RNAs that support DNA packaging.

Science.gov (United States)

Fang, Yun; Shu, Dan; Xiao, Feng; Guo, Peixuan; Qin, Peter Z

2008-08-08

The bacteriophage phi29 DNA packaging motor is a protein/RNA complex that can produce strong force to condense the linear-double-stranded DNA genome into a pre-formed protein capsid. The RNA component, called the packaging RNA (pRNA), utilizes magnesium-dependent inter-molecular base-pairing interactions to form ring-shaped complexes. The pRNA is a class of non-coding RNA, interacting with phi29 motor proteins to enable DNA packaging. Here, we report a two-piece chimeric pRNA construct that is fully competent in interacting with partner pRNA to form ring-shaped complexes, in packaging DNA via the motor, and in assembling infectious phi29 virions in vitro. This is the first example of a fully functional pRNA assembled using two non-covalently interacting fragments. The results support the notion of modular pRNA architecture in the phi29 packaging motor.

Color-Coded Front-of-Pack Nutrition Labels—An Option for US Packaged Foods?

Science.gov (United States)

Dunford, Elizabeth K.; Poti, Jennifer M.; Xavier, Dagan; Webster, Jacqui L.; Taillie, Lindsey Smith

2017-01-01

The implementation of a standardized front-of-pack-labelling (FoPL) scheme would likely be a useful tool for many consumers trying to improve the healthfulness of their diets. Our objective was to examine what the traffic light labelling scheme would look like if implemented in the US. Data were extracted from Label Insight’s Open Access branded food database in 2017. Nutrient levels and the proportion of products classified as “Red” (High), “Amber” (Medium) or “Green” (Low) in total fat, saturated fat, total sugar and sodium for food and beverage items were examined. The proportion of products in each category that had each possible combination of traffic light colors, and met the aggregate score for “healthy” was examined. Out of 175,198 products, >50% of all US packaged foods received a “Red” rating for total sugar and sodium. “Confectionery” had the highest mean total sugar (51.9 g/100 g) and “Meat and meat alternatives” the highest mean sodium (781 mg/100 g). The most common traffic light label combination was “Red” for total fat, saturated fat and sodium and “Green” for sugar. Only 30.1% of products were considered “healthy”. A wide variety (n = 80) of traffic light color combinations were observed. A color coded traffic light scheme appears to be an option for implementation across the US packaged food supply to support consumers in making healthier food choices. PMID:28489037

Stability Analysis of Buffer Storage Large Basket and Temporary Storage Pre-packaging Basket Used in the Type B Radwaste Process Area

International Nuclear Information System (INIS)

Kim, Sung Kyun; Lee, Kune Woo; Moon, Jei Kwon

2011-01-01

The ITER radioactive waste (radwaste) treatment and storage systems are currently being designed to manage Type B, Type A and dust radwastes generated during the ITER machine operation. The Type B management system is to be in the hot cell building basement with temporary storage and the modular type storages outside the hot cell building for the pre-packed Type B radwaste during the ITER operation of 20 years. In order to store Type B radwaste components in onsite storage, the waste treatment chain process for Type B radwastes was developed as follows. First, Type B full components filled in a large basket are imported from Tokamak to the hot cell basement and they are stored in the buffer storage before treatment. Second, they are cut properly with a laser cutting machine or band saw machine and sliced waste parts are filled in a pre-packaging basket. Third, the sampling of Type B components is performed and then the tritium removal treatment is done in an oven to remove tritium from the waste surface and then the sampling is performed again. Forth, the characterization is performed by using a gamma spectrometry. Fifth, the pre-packaging operation is done to ensure the final packaging of the radwaste. Sixth, the pre-packaging baskets are stored in the temporary storage for 6 months and then they are sent to the extension storage and stored until export to host country. One of issues in the waste treatment scheme is to analyze the stacking stability of a stack of large baskets and pre-packaging baskets in the storage system. The baseline plan is to stack the large baskets in two layers in the buffer storage and to stack the pre-packaging baskets in three layers in the temporary storage and extension storage. In this study, the stacking stability analysis for the buffer storage large basket and temporary storage pre-packaging basket was performed for various stack failure modes

Safety analysis of spent fuel packaging

International Nuclear Information System (INIS)

Akamatsu, Hiroshi; Taniuchi, Hiroaki; Tai, Hideto

1987-01-01

Many types of spent fuel packagings have been manufactured and been used for transport of spent fuels discharged from nuclear power plant. These spent fuel packagings need to be assesed thoroughly about safety transportation because spent fuels loaded into the packaging have high radioactivity and generation of heat. This paper explains the outline of safety analysis of a packaging, Safety analysis is performed for structural, thermal, containment, shielding and criticality factors, and MARC-CDC, TRUMP, ORIGEN, QAD, ANISN, KENO, etc computer codes are used for such analysis. (author)

Sensitivity analysis of the RESRAD, a dose assessment code

International Nuclear Information System (INIS)

Yu, C.; Cheng, J.J.; Zielen, A.J.

1991-01-01

The RESRAD code is a pathway analysis code that is designed to calculate radiation doses and derive soil cleanup criteria for the US Department of Energy's environmental restoration and waste management program. the RESRAD code uses various pathway and consumption-rate parameters such as soil properties and food ingestion rates in performing such calculations and derivations. As with any predictive model, the accuracy of the predictions depends on the accuracy of the input parameters. This paper summarizes the results of a sensitivity analysis of RESRAD input parameters. Three methods were used to perform the sensitivity analysis: (1) Gradient Enhanced Software System (GRESS) sensitivity analysis software package developed at oak Ridge National Laboratory; (2) direct perturbation of input parameters; and (3) built-in graphic package that shows parameter sensitivities while the RESRAD code is operational

The application package DeCA for calculating cyclic accelerators

International Nuclear Information System (INIS)

Gladkikh, P.I.; Zelinsky, A.Yu.; Strelkov, M.A.

1993-01-01

The application Package DeCA (Design Cyclic Accelerator) is offered to solve a set of problem which arise on designing electron storage rings. The package is based on the block principle. This makes it extremely flexible in designing storage rings and investigating beam dynamics in them. The package is intended for a user not familiar with programming languages, it is arranged so that the user familiar with FORTRAN-77 can easily extend the package functions. This is of particular interest, when the input data are the storage ring or electron bunch parameters. The code allows operation in both the batch and interactive modes. The programming language is FORTRAN-77. The capacity of the total package is 40,000 code lines. The necessary main storage capacity for the total version is 4 Mbytes

The correspondence between projective codes and 2-weight codes

NARCIS (Netherlands)

Brouwer, A.E.; Eupen, van M.J.M.; Tilborg, van H.C.A.; Willems, F.M.J.

1994-01-01

The hyperplanes intersecting a 2-weight code in the same number of points obviously form the point set of a projective code. On the other hand, if we have a projective code C, then we can make a 2-weight code by taking the multiset of points E PC with multiplicity "Y(w), where W is the weight of

A Fast Healthcare Interoperability Resources (FHIR) layer implemented over i2b2.

Science.gov (United States)

Boussadi, Abdelali; Zapletal, Eric

2017-08-14

Standards and technical specifications have been developed to define how the information contained in Electronic Health Records (EHRs) should be structured, semantically described, and communicated. Current trends rely on differentiating the representation of data instances from the definition of clinical information models. The dual model approach, which combines a reference model (RM) and a clinical information model (CIM), sets in practice this software design pattern. The most recent initiative, proposed by HL7, is called Fast Health Interoperability Resources (FHIR). The aim of our study was to investigate the feasibility of applying the FHIR standard to modeling and exposing EHR data of the Georges Pompidou European Hospital (HEGP) integrating biology and the bedside (i2b2) clinical data warehouse (CDW). We implemented a FHIR server over i2b2 to expose EHR data in relation with five FHIR resources: DiagnosisReport, MedicationOrder, Patient, Encounter, and Medication. The architecture of the server combines a Data Access Object design pattern and FHIR resource providers, implemented using the Java HAPI FHIR API. Two types of queries were tested: query type #1 requests the server to display DiagnosticReport resources, for which the diagnosis code is equal to a given ICD-10 code. A total of 80 DiagnosticReport resources, corresponding to 36 patients, were displayed. Query type #2, requests the server to display MedicationOrder, for which the FHIR Medication identification code is equal to a given code expressed in a French coding system. A total of 503 MedicationOrder resources, corresponding to 290 patients, were displayed. Results were validated by manually comparing the results of each request to the results displayed by an ad-hoc SQL query. We showed the feasibility of implementing a Java layer over the i2b2 database model to expose data of the CDW as a set of FHIR resources. An important part of this work was the structural and semantic mapping between the

Qualification and improvement of iron ENDF/B-VI and JEF-2 evaluations by interpretation of the Aspis Benchmark

International Nuclear Information System (INIS)

Zheng, S.H.; Kodeli, I.; Raepsaet, C.; Diop, C.M.; Nimal, J.C.; Monnier, A.

1992-01-01

The aim of the present study is to contribute to the validation of the new evaluated nuclear data files like ENDF/B-VI or JEF-2.2. The new cross-section evaluation for iron isotopes are of particular interest for the nuclear community, since it is well known that the ENDF/B-IV data underestimate the neutron flux on deep penetration problems. The performances of the new nuclear data libraries are compared with those of ENDF-B-IV. The ASPIS benchmark, where the neutron transports through more than one meter iron plate, was chosen for this study. The cross-section libraries were produced by the THEMIS/NJOY (ref 1) processing system and the transport calculations were carried out using the 3D Monte-Carlo code TRIPOLI. The influence of different multigroup cross-section representations was investigated. Finally, sensitivity, uncertainty and data adjustment analyses were carried out to obtain some additional informations about the quality of the cross-section data in ENDF/B-VI files. The analyses were performed using the code package set up of different modules, either developed at CEA or obtained from the NEA Data Bank. The adjustment indicated that some modifications have to be introduced to the neutron cross-sections of iron and the whole calculations were repeated with the adjusted set of cross sections. The comparison of the results of the uncertainty and the adjustment analyses applied to ENDF/B-IV and ENDF/B-VI iron data permits to establish the progress made and gives some indications about the state-of-the-art of the cross-section data

Safety analysis report on Model UC-609 shipping package

International Nuclear Information System (INIS)

Sandberg, R.R.

1977-08-01

This Safety Analysis Report for Packaging demonstrates that model UC-609 shipping package can safely transport tritium in any of its forms. The package and its contents are described. The package when subjected to the transport conditions specified in the Code of Federal Regulations, Title 10, Part 71 is evaluated. Finally, compliance with these regulations is discussed

Interactive orbit control package for INDUS-2 storage ring

International Nuclear Information System (INIS)

Walia, A.A.S.; Ghodke, A.D.; Fatnani, Pravin; Bhujle, A.G.; Singh, Gurnam

2003-01-01

Maintaining the proper electron beam orbit is very important for all light sources. This package designed in Meatball provides for orbit control by just drag and drop. Simulation of Indus-2 storage ring in this package makes it useful for beam dynamic studies as well. Package functionality and architecture is described. (author)

Interactive orbit control package for INDUS-2 storage ring

Energy Technology Data Exchange (ETDEWEB)

Walia, A A.S.; Ghodke, A D; Fatnani, Pravin; Bhujle, A G; Singh, Gurnam [Centre for Advanced Technology, Indore (India)

2003-07-01

Maintaining the proper electron beam orbit is very important for all light sources. This package designed in Meatball provides for orbit control by just drag and drop. Simulation of Indus-2 storage ring in this package makes it useful for beam dynamic studies as well. Package functionality and architecture is described. (author)

Self-shielding models of MICROX-2 code: Review and updates

International Nuclear Information System (INIS)

Hou, J.; Choi, H.; Ivanov, K.N.

2014-01-01

Highlights: • The MICROX-2 code has been improved to expand its application to advanced reactors. • New fine-group cross section libraries based on ENDF/B-VII have been generated. • Resonance self-shielding and spatial self-shielding models have been improved. • The improvements were assessed by a series of benchmark calculations against MCNPX. - Abstract: The MICROX-2 is a transport theory code that solves for the neutron slowing-down and thermalization equations of a two-region lattice cell. The MICROX-2 code has been updated to expand its application to advanced reactor concepts and fuel cycle simulations, including generation of new fine-group cross section libraries based on ENDF/B-VII. In continuation of previous work, the MICROX-2 methods are reviewed and updated in this study, focusing on its resonance self-shielding and spatial self-shielding models for neutron spectrum calculations. The improvement of self-shielding method was assessed by a series of benchmark calculations against the Monte Carlo code, using homogeneous and heterogeneous pin cell models. The results have shown that the implementation of the updated self-shielding models is correct and the accuracy of physics calculation is improved. Compared to the existing models, the updates reduced the prediction error of the infinite multiplication factor by ∼0.1% and ∼0.2% for the homogeneous and heterogeneous pin cell models, respectively, considered in this study

Nuclear critical safety analysis for UX-30 transport of freight package

International Nuclear Information System (INIS)

Quan Yanhui; Zhou Qi; Yin Shenggui

2014-01-01

The nuclear critical safety analysis and evaluation for UX-30 transport freight package in the natural condition and accident condition were carried out with MONK-9A code and MCNP code. Firstly, the critical benchmark experiment data of public in international were selected, and the deflection and subcritical limiting value with MONK-9A code and MCNP code in calculating same material form were validated and confirmed. Secondly, the neutron efficiency multiplication factors in the natural condition and accident condition were calculated and analyzed, and the safety in transport process was evaluated by taking conservative suppose of nuclear critical safety. The calculation results show that the max value of k eff for UX-30 transport freight package is less than the subcritical limiting value, and the UX-30 transport freight package is in the state of subcritical safety. Moreover, the critical safety index (CSI) for UX-30 package can define zero based on the definition of critical safety index. (authors)

BrachyTPS -Interactive point kernel code package for brachytherapy treatment planning of gynaecological cancers

International Nuclear Information System (INIS)

Thilagam, L.; Subbaiah, K.V.

2008-01-01

Brachytherapy treatment planning systems (TPS) are always recommended to account for the effect of tissue, applicator and shielding material heterogeneities exist in Intracavitary brachytherapy (ICBT) applicators. Most of the commercially available brachytherapy TPS softwares estimate the absorbed dose at a point, only taking care of the contributions of individual sources and the source distribution, neglecting the dose perturbations arising from the applicator design and construction. So the doses estimated by them are not much accurate under realistic clinical conditions. In this regard, interactive point kernel rode (BrachyTPS) has been developed to perform independent dose calculations by taking into account the effect of these heterogeneities, using two regions build up factors, proposed by Kalos. As primary input data, the code takes patients' planning data including the source specifications, dwell positions, dwell times and it computes the doses at reference points by dose point kernel formalisms, with multi-layer shield build-up factors accounting for the contributions from scattered radiation. In addition to performing dose distribution calculations, this code package is capable of displaying an isodose distribution curve into the patient anatomy images. The primary aim of this study is to validate the developed point kernel code integrated with treatment planning systems against the other tools which are available in the market. In the present work, three brachytherapy applicators commonly used in the treatment of uterine cervical carcinoma, Board of Radiation Isotope and Technology (BRIT) made low dose rate (LDR) applicator, Fletcher Green type LDR applicator and Fletcher Williamson high dose rate (HDR) applicator were studied to test the accuracy of the software

2D numerical comparison of trailing edge flaps - UpWind WP1B3

Energy Technology Data Exchange (ETDEWEB)

Buhl, T.; Andersen, Peter B. (Risoe National Lab., DTU (DK)); Barlas, T.K. (DUWIND, Delft Technical Univ. (NL))

2007-11-15

This report covers the investigations and comparisons of trailing edge flaps carried out by Delft and Risoe. The work is a part of the W1B3 work package of the UpWind EU-project. This report covers only 2D test cases with simple control of the trailing edge flap with the objective of keeping CL constant. The 5MW UpWind reference turbine is used for the calculations. The section in 75% radius is investigated for three different cases; (1) a wind step from 10m/s to 11m/s, (2) a wind 'gust' from 10 m/s to 14m/s in 1 second and followed by 10m/s, (3) finally a turbulent wind series is simulated, and the performance of the flaps is investigated. The two different codes from Delft and Risoe are compared in the mentioned cases. (au)

An improved version of the MICROX-2 code

Energy Technology Data Exchange (ETDEWEB)

Mathews, D. [Paul Scherrer Inst. (PSI), Villigen (Switzerland)

1997-11-01

The MICROX-2 code prepares broad group neutron cross sections for use in diffusion- and/or transport-theory codes from an input library of fine group and pointwise cross sections. The neutron weighting spectrum is obtained by solving the B{sub 1} neutron balance equations at about 10000 energies in a one-dimensional (planar, spherical or cylindrical), two-region unit cell. The regions are coupled by collision probabilities based upon spatially flat neutron emission. Energy dependent Dancoff factors and bucklings correct the one-dimensional calculations for multi-dimensional lattice effects. A critical buckling search option is also included. The inner region may include two different types of fuel particles (grains). This report describes the present PSI FORTRAN 90 version of the MICROX-2 code which operates on CRAY computers and IBM PC`s. The equations which are solved in the various energy ranges are given along with descriptions of various changes that have been made in the present PSI version of the code. A completely re-written description of the user input is also included. (author) 7 figs., 4 tabs., 59 refs.

TOPICAL REPORT ON ACTINIDE-ONLY BURNUP CREDIT FOR PWR SPENT NUCLEAR FUEL PACKAGES

International Nuclear Information System (INIS)

DOE

1997-01-01

A methodology for performing and applying nuclear criticality safety calculations, for PWR spent nuclear fuel (SNF) packages with actinide-only burnup credit, is described. The changes in the U-234, U-235, U-236, U-238, Pu-238, Pu-239, Pu-240, Pu-241, Pu-242, and Am-241 concentration with burnup are used in burnup credit criticality analyses. No credit for fission product neutron absorbers is taken. The methodology consists of five major steps. (1) Validate a computer code system to calculate isotopic concentrations of SNF created during burnup in the reactor core and subsequent decay. A set of chemical assay benchmarks is presented for this purpose as well as a method for assessing the calculational bias and uncertainty, and conservative correction factors for each isotope. (2) Validate a computer code system to predict the subcritical multiplication factor, k eff , of a spent nuclear fuel package. Fifty-seven UO 2 , UO 2 /Gd 2 O 3 , and UO 2 /PuO 2 critical experiments have been selected to cover anticipated conditions of SNF. The method uses an upper safety limit on k eff (which can be a function of the trending parameters) such that the biased k eff , when increased for the uncertainty is less than 0.95. (3) Establish bounding conditions for the isotopic concentration and criticality calculations. Three bounding axial profiles have been established to assure the ''end effect'' is accounted for conservatively. (4) Use the validated codes and bounding conditions to generate package loading criteria (burnup credit loading curves). Burnup credit loading curves show the minimum burnup required for a given initial enrichment. The utility burnup record is compared to this requirement after the utility accounts for the uncertainty in its record. Separate curves may be generated for each assembly design, various minimum cooling times and burnable absorber histories. (5) Verify that SNF assemblies meet the package loading criteria and confirm proper assembly selection

Development of an integrated thermal-hydraulics capability incorporating RELAP5 and PANTHER neutronics code

Energy Technology Data Exchange (ETDEWEB)

Page, R.; Jones, J.R.

1997-07-01

Ensuring that safety analysis needs are met in the future is likely to lead to the development of new codes and the further development of existing codes. It is therefore advantageous to define standards for data interfaces and to develop software interfacing techniques which can readily accommodate changes when they are made. Defining interface standards is beneficial but is necessarily restricted in application if future requirements are not known in detail. Code interfacing methods are of particular relevance with the move towards automatic grid frequency response operation where the integration of plant dynamic, core follow and fault study calculation tools is considered advantageous. This paper describes the background and features of a new code TALINK (Transient Analysis code LINKage program) used to provide a flexible interface to link the RELAP5 thermal hydraulics code with the PANTHER neutron kinetics and the SIBDYM whole plant dynamic modelling codes used by Nuclear Electric. The complete package enables the codes to be executed in parallel and provides an integrated whole plant thermal-hydraulics and neutron kinetics model. In addition the paper discusses the capabilities and pedigree of the component codes used to form the integrated transient analysis package and the details of the calculation of a postulated Sizewell `B` Loss of offsite power fault transient.

Development of an integrated thermal-hydraulics capability incorporating RELAP5 and PANTHER neutronics code

International Nuclear Information System (INIS)

Page, R.; Jones, J.R.

1997-01-01

Ensuring that safety analysis needs are met in the future is likely to lead to the development of new codes and the further development of existing codes. It is therefore advantageous to define standards for data interfaces and to develop software interfacing techniques which can readily accommodate changes when they are made. Defining interface standards is beneficial but is necessarily restricted in application if future requirements are not known in detail. Code interfacing methods are of particular relevance with the move towards automatic grid frequency response operation where the integration of plant dynamic, core follow and fault study calculation tools is considered advantageous. This paper describes the background and features of a new code TALINK (Transient Analysis code LINKage program) used to provide a flexible interface to link the RELAP5 thermal hydraulics code with the PANTHER neutron kinetics and the SIBDYM whole plant dynamic modelling codes used by Nuclear Electric. The complete package enables the codes to be executed in parallel and provides an integrated whole plant thermal-hydraulics and neutron kinetics model. In addition the paper discusses the capabilities and pedigree of the component codes used to form the integrated transient analysis package and the details of the calculation of a postulated Sizewell 'B' Loss of offsite power fault transient

Radioisotope thermoelectric generator transportation system safety analysis report for packaging. Volumes 1 and 2

International Nuclear Information System (INIS)

Ferrell, P.C.

1996-01-01

This SARP describes the RTG Transportation System Package, a Type B(U) packaging system that is used to transport an RTG or similar payload. The payload, which is included in this SARP, is a generic, enveloping payload that specifically encompasses the General Purpose Heat Source (GPHS) RTG payload. The package consists of two independent containment systems mounted on a shock isolation transport skid and transported within an exclusive-use trailer

Radioisotope thermoelectric generator transportation system safety analysis report for packaging. Volumes 1 and 2

Energy Technology Data Exchange (ETDEWEB)

Ferrell, P.C.

1996-04-18

This SARP describes the RTG Transportation System Package, a Type B(U) packaging system that is used to transport an RTG or similar payload. The payload, which is included in this SARP, is a generic, enveloping payload that specifically encompasses the General Purpose Heat Source (GPHS) RTG payload. The package consists of two independent containment systems mounted on a shock isolation transport skid and transported within an exclusive-use trailer.

Improvement and validation of the wall heat transfer package of RELAP5/MOD3.3

International Nuclear Information System (INIS)

Wu, Pan; Xiong, Xiaofei; Shan, Jianqiang; Gou, Junli; Zhang, Bin; Zhang, Bo

2016-01-01

Highlights: • A new heat transfer package has been developed. • It has been incorporated into RELAP5/MOD3.3 to verify its advantages. • The results of modified code were compared with available experimental data. • The results showed that higher prediction accuracy was achieved. - Abstract: The process of energy transfer from heat structure to control volume is determined by the wall-to-fluid heat transfer package, which is crucial for nuclear reactor safety analysis codes. The current logic for selection of heat transfer modes of RELAP5/MOD3.3 code is too complex and may result in incorrect heat transfer mode judgment. Also, the narrow application scope of film boiling heat transfer correlations may result in large errors in film boiling region which is of paramount importance for the predicted peak clad temperatures during hypothetical LB-LOCAs in PWRs. In this study, a new heat transfer package has been developed and incorporated into the RELAP5/MOD3.3 code. Differing from the original package, the modified one consists of twelve heat transfer modes and proposes a new logic for selection of heat transfer modes. For each mode, the models in the existing safety analysis codes and the leading models in literature have been reviewed in order to determine the best model which can easily be applicable to the RELAP5/MOD3.3 code. Particularly (1) a new package of heat transfer correlations are produced; (2) a new logic for selection of film boiling and transition boiling heat transfer modes is proposed which use minimum film boiling temperature and critical heat flux temperature as distinguished points. The modified code has been validated by comparing the analysis results with available experimental data from tube post dryout experiments and loss-of-fluid test (LOFT) facility. The calculation results showed that the improved package could better predict the experimental phenomena with higher prediction accuracy.

Improvement and validation of the wall heat transfer package of RELAP5/MOD3.3

Energy Technology Data Exchange (ETDEWEB)

Wu, Pan; Xiong, Xiaofei; Shan, Jianqiang, E-mail: jqshan@mail.xjtu.edu.cn; Gou, Junli; Zhang, Bin; Zhang, Bo

2016-12-15

Highlights: • A new heat transfer package has been developed. • It has been incorporated into RELAP5/MOD3.3 to verify its advantages. • The results of modified code were compared with available experimental data. • The results showed that higher prediction accuracy was achieved. - Abstract: The process of energy transfer from heat structure to control volume is determined by the wall-to-fluid heat transfer package, which is crucial for nuclear reactor safety analysis codes. The current logic for selection of heat transfer modes of RELAP5/MOD3.3 code is too complex and may result in incorrect heat transfer mode judgment. Also, the narrow application scope of film boiling heat transfer correlations may result in large errors in film boiling region which is of paramount importance for the predicted peak clad temperatures during hypothetical LB-LOCAs in PWRs. In this study, a new heat transfer package has been developed and incorporated into the RELAP5/MOD3.3 code. Differing from the original package, the modified one consists of twelve heat transfer modes and proposes a new logic for selection of heat transfer modes. For each mode, the models in the existing safety analysis codes and the leading models in literature have been reviewed in order to determine the best model which can easily be applicable to the RELAP5/MOD3.3 code. Particularly (1) a new package of heat transfer correlations are produced; (2) a new logic for selection of film boiling and transition boiling heat transfer modes is proposed which use minimum film boiling temperature and critical heat flux temperature as distinguished points. The modified code has been validated by comparing the analysis results with available experimental data from tube post dryout experiments and loss-of-fluid test (LOFT) facility. The calculation results showed that the improved package could better predict the experimental phenomena with higher prediction accuracy.

Testing of Type A and B packages in accordance with IAEA transport regulations

International Nuclear Information System (INIS)

Nitsche, F.; Runge, K.; Birkigt, W.; Mueller, E.

1984-01-01

Revised and extended version of a paper presented during the Interregional Training Course on the Safe Transport of Radioactive Materials, organized by the IAEA, Harwell, May 1982, dealing with the test conditions for Type A and Type B packages as well as possible test methods, the performance of testing, and the assessmnt of test results

DNA Topology and the Initiation of Virus DNA Packaging.

Directory of Open Access Journals (Sweden)

Choon Seok Oh

Full Text Available During progeny assembly, viruses selectively package virion genomes from a nucleic acid pool that includes host nucleic acids. For large dsDNA viruses, including tailed bacteriophages and herpesviruses, immature viral DNA is recognized and translocated into a preformed icosahedral shell, the prohead. Recognition involves specific interactions between the viral packaging enzyme, terminase, and viral DNA recognition sites. Generally, viral DNA is recognized by terminase's small subunit (TerS. The large terminase subunit (TerL contains translocation ATPase and endonuclease domains. In phage lambda, TerS binds a sequence repeated three times in cosB, the recognition site. TerS binding to cosB positions TerL to cut the concatemeric DNA at the adjacent nicking site, cosN. TerL introduces staggered nicks in cosN, generating twelve bp cohesive ends. Terminase separates the cohesive ends and remains bound to the cosB-containing end, in a nucleoprotein structure called Complex I. Complex I docks on the prohead's portal vertex and translocation ensues. DNA topology plays a role in the TerSλ-cosBλ interaction. Here we show that a site, I2, located between cosN and cosB, is critically important for an early DNA packaging step. I2 contains a complex static bend. I2 mutations block DNA packaging. I2 mutant DNA is cut by terminase at cosN in vitro, but in vivo, no cos cleavage is detected, nor is there evidence for Complex I. Models for what packaging step might be blocked by I2 mutations are presented.

MIFT: GIFT Combinatorial Geometry Input to VCS Code

Science.gov (United States)

1977-03-01

r-w w-^ H ^ß0318is CQ BRL °RCUMr REPORT NO. 1967 —-S: ... MIFT: GIFT COMBINATORIAL GEOMETRY INPUT TO VCS CODE Albert E...TITLE (and Subtitle) MIFT: GIFT Combinatorial Geometry Input to VCS Code S. TYPE OF REPORT & PERIOD COVERED FINAL 6. PERFORMING ORG. REPORT NUMBER...Vehicle Code System (VCS) called MORSE was modified to accept the GIFT combinatorial geometry package. GIFT , as opposed to the geometry package

Alternate Materials In Design Of Radioactive Material Packages

International Nuclear Information System (INIS)

Blanton, P.; Eberl, K.

2010-01-01

This paper presents a summary of design and testing of material and composites for use in radioactive material packages. These materials provide thermal protection and provide structural integrity and energy absorption to the package during normal and hypothetical accident condition events as required by Title 10 Part 71 of the Code of Federal Regulations. Testing of packages comprising these materials is summarized.

Qualification testing facility for type A, B and C packages to be used for transport and storage of radioactive materials

International Nuclear Information System (INIS)

Vieru, G.; Nistor, V.; Vasile, A.; Cojocaru, V.

2009-01-01

In accordance with the Economic Commission for Europe-Committee on inland transport (ADR- European Agreement-concerning the international carriage of dangerous goods by road, 2007 Edition) the Safety and Security of the dangerous goods class No. 7 - Radioactive Materials during transport in all different modes - by road, by rail, by sea, by inland rivers or by air - have to be ensured at a very high level. The radioactive materials (RAM) packaging have to comply to all transport conditions, routine or in accident conditions, possibly to occur during transportation operations. It is well known that the safety in the transport of RAM is dependent on packaging appropriate for the contents being shipped rather than on operational and/or administrative actions required for the package. The quality of these packages - type A, B or C has to be proved by performing qualification tests in accordance with the Romanian nuclear regulation conditions provided by CNCAN Order no. 357/22.12.2005- N orms for a Safe Transport of Radioactive Material , the IAEA Vienna Recommendation (1, 2) stipulated in the Safety standard TS-R-1- Regulation for the Safe Transport of Radioactive Material, 2005 Edition, and other applicable international recommendations. The paper will describe the components of the designed testing facilities, and the qualification testing to be performed for all type A, B and C packages subjected to the testing Quality assurance and quality controls measures taken in order to meet technical specification provided by the design are also presented and commented. The paper concludes that the new Romanian Testing Facilities for RAM packages will comply with the national safe standards as well as with the IAEA applicable recommendation provided by the TS-R-1 safety standard. (authors)

The drift-flux correlation package MDS

International Nuclear Information System (INIS)

Hoeld, A.

2001-01-01

Based on the SONNENBURG drift-flux correlation, developed at GRS/Garching (Germany), a comprehensive drift-flux correlation package (MDS) has been established. Its aim is to support thermal-hydraulic mixture-fluid models, models being used for the simulation of the steady state and transient behaviour of characteristic thermal-hydraulic parameters of single- or two-phase fluids flowing along coolant channels of different types (being, e.g., parts of NPP-s, steam generators etc.). The characteristic properties of this package with respect to the behaviour at co- and counter-current flow, its inverse solutions needed for steady state simulations, its behaviour when approaching the lower or upper boundary of a two-phase region, its verification and behaviour with respect to other correlations will be discussed. An adequate driver code, MDSDRI, has been established too, allowing to test the package very thoroughly out of the complex thermal-hydraulic codes. (author)

The drift-flux correlation package MDS

Energy Technology Data Exchange (ETDEWEB)

Hoeld, A. [Bernaysstr. 16A, Munich, F.R. (Germany)

2001-07-01

Based on the SONNENBURG drift-flux correlation, developed at GRS/Garching (Germany), a comprehensive drift-flux correlation package (MDS) has been established. Its aim is to support thermal-hydraulic mixture-fluid models, models being used for the simulation of the steady state and transient behaviour of characteristic thermal-hydraulic parameters of single- or two-phase fluids flowing along coolant channels of different types (being, e.g., parts of NPP-s, steam generators etc.). The characteristic properties of this package with respect to the behaviour at co- and counter-current flow, its inverse solutions needed for steady state simulations, its behaviour when approaching the lower or upper boundary of a two-phase region, its verification and behaviour with respect to other correlations will be discussed. An adequate driver code, MDSDRI, has been established too, allowing to test the package very thoroughly out of the complex thermal-hydraulic codes. (author)

Sizing of type B package tie-downs on the basis of criteria related to hypothetical road transport accident conditions

International Nuclear Information System (INIS)

Phalippou, C.

1986-01-01

The aim is to guarantee intactness of the type B package containment system under hypothetical road accident conditions. Some experiments performed in France have led to analytical studies taking into account: a) the head-on collision, which is modelised by a uniform deceleration of 35 g, b) the side-on collision, which is modelised by a colliding object 3 times heavier than the package and an impact at 31.9 km/h. In the first case, the adopted criterion is the holding of the package on the vehicle by the strenght of the stowing members (tie-downs and chocks). In the second case, the adopted criterion is the desired breaking of the tie-downs in order to undamage package containment system; therefore it is assumed that no chock is acting against lateral impacts. Analytical and abacus methods have been developed for sizing the strenght of the stowing members in respect with the two above criteria [fr

Use of computer codes for system reliability analysis

International Nuclear Information System (INIS)

Sabek, M.; Gaafar, M.; Poucet, A.

1989-01-01

This paper gives a summary of studies performed at the JRC, ISPRA on the use of computer codes for complex systems analysis. The computer codes dealt with are: CAFTS-SALP software package, FRACTIC, FTAP, computer code package RALLY, and BOUNDS. Two reference case studies were executed by each code. The probabilistic results obtained, as well as the computation times are compared. The two cases studied are the auxiliary feedwater system of a 1300 MW PWR reactor and the emergency electrical power supply system. (author)

Use of computer codes for system reliability analysis

Energy Technology Data Exchange (ETDEWEB)

Sabek, M.; Gaafar, M. (Nuclear Regulatory and Safety Centre, Atomic Energy Authority, Cairo (Egypt)); Poucet, A. (Commission of the European Communities, Ispra (Italy). Joint Research Centre)

1989-01-01

This paper gives a summary of studies performed at the JRC, ISPRA on the use of computer codes for complex systems analysis. The computer codes dealt with are: CAFTS-SALP software package, FRACTIC, FTAP, computer code package RALLY, and BOUNDS. Two reference case studies were executed by each code. The probabilistic results obtained, as well as the computation times are compared. The two cases studied are the auxiliary feedwater system of a 1300 MW PWR reactor and the emergency electrical power supply system. (author).

Icarus: A 2-D Direct Simulation Monte Carlo (DSMC) Code for Multi-Processor Computers

International Nuclear Information System (INIS)

BARTEL, TIMOTHY J.; PLIMPTON, STEVEN J.; GALLIS, MICHAIL A.

2001-01-01

Icarus is a 2D Direct Simulation Monte Carlo (DSMC) code which has been optimized for the parallel computing environment. The code is based on the DSMC method of Bird[11.1] and models from free-molecular to continuum flowfields in either cartesian (x, y) or axisymmetric (z, r) coordinates. Computational particles, representing a given number of molecules or atoms, are tracked as they have collisions with other particles or surfaces. Multiple species, internal energy modes (rotation and vibration), chemistry, and ion transport are modeled. A new trace species methodology for collisions and chemistry is used to obtain statistics for small species concentrations. Gas phase chemistry is modeled using steric factors derived from Arrhenius reaction rates or in a manner similar to continuum modeling. Surface chemistry is modeled with surface reaction probabilities; an optional site density, energy dependent, coverage model is included. Electrons are modeled by either a local charge neutrality assumption or as discrete simulational particles. Ion chemistry is modeled with electron impact chemistry rates and charge exchange reactions. Coulomb collision cross-sections are used instead of Variable Hard Sphere values for ion-ion interactions. The electro-static fields can either be: externally input, a Langmuir-Tonks model or from a Green's Function (Boundary Element) based Poison Solver. Icarus has been used for subsonic to hypersonic, chemically reacting, and plasma flows. The Icarus software package includes the grid generation, parallel processor decomposition, post-processing, and restart software. The commercial graphics package, Tecplot, is used for graphics display. All of the software packages are written in standard Fortran

Research and Development Program for transportation packagings at Sandia National Laboratories

International Nuclear Information System (INIS)

Hohnstreiter, G.F.; Sorenson, K.B.

1995-01-01

This document contains information about the research and development programs dealing with waste transport at Sandia National Laboratories. This paper discusses topics such as: Why new packaging is needed; analytical methodologies and design codes;evaluation of packaging components; materials characterization; creative packaging concepts; packaging engineering and analysis; testing; and certification support

ENDF/B Pre-Processing Codes: Implementing and testing on a Personal Computer

International Nuclear Information System (INIS)

McLaughlin, P.K.

1987-05-01

This document describes the contents of the diskettes containing the ENDF/B Pre-Processing codes by D.E. Cullen, and example data for use in implementing and testing these codes on a Personal Computer of the type IBM-PC/AT. Upon request the codes are available from the IAEA Nuclear Data Section, free of charge, on a series of 7 diskettes. (author)

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2006-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant| (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations(CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

CH Packaging Program Guidance

International Nuclear Information System (INIS)

2007-01-01

The purpose of this document is to provide the technical requirements for preparation for use, operation, inspection, and maintenance of a Transuranic Package Transporter Model II (TRUPACT-II), a HalfPACT shipping package, and directly related components. This document complies with the minimum requirements as specified in the TRUPACT-II Safety Analysis Report for Packaging (SARP), HalfPACT SARP, and U.S. Nuclear Regulatory Commission (NRC) Certificates of Compliance (C of C) 9218 and 9279, respectively. In the event of a conflict between this document and the SARP or C of C, the C of C shall govern. The C of Cs state: 'each package must be prepared for shipment and operated in accordance with the procedures described in Chapter 7.0, Operating Procedures, of the application.' They further state: 'each package must be tested and maintained in accordance with the procedures described in Chapter 8.0, Acceptance Tests and Maintenance Program of the Application.' Chapter 9.0 of the SARP charges the U.S. Department of Energy (DOE) or the Waste Isolation Pilot Plant (WIPP) management and operating (M and O) contractor with assuring packaging is used in accordance with the requirements of the C of C. Because the packaging is NRC-approved, users need to be familiar with Title 10 Code of Federal Regulations (CFR) 71.8. Any time a user suspects or has indications that the conditions of approval in the C of C were not met, the Carlsbad Field Office (CBFO) shall be notified immediately. The CBFO will evaluate the issue and notify the NRC if required.In accordance with 10 CFR Part 71, certificate holders, packaging users, and contractors or subcontractors who use, design, fabricate, test, maintain, or modify the packaging shall post copies of (1) 10 CFR Part 21 regulations, (2) Section 206 of the Energy Reorganization Act of 1974, and (3) NRC Form 3, Notice to Employees. These documents must be posted in a conspicuous location where the activities subject to these regulations

Extracellular vesicle associated long non-coding RNAs functionally enhance cell viability

Directory of Open Access Journals (Sweden)

Chris Hewson

2016-10-01

Full Text Available Cells communicate with one another to create microenvironments and share resources. One avenue by which cells communicate is through the action of exosomes. Exosomes are extracellular vesicles that are released by one cell and taken up by neighbouring cells. But how exosomes instigate communication between cells has remained largely unknown. We present evidence here that particular long non-coding RNA molecules are preferentially packaged into exosomes. We also find that a specific class of these exosome associated non-coding RNAs functionally modulate cell viability by direct interactions with l-lactate dehydrogenase B (LDHB, high-mobility group protein 17 (HMG-17, and CSF2RB, proteins involved in metabolism, nucleosomal architecture and cell signalling respectively. Knowledge of this endogenous cell to cell pathway, those proteins interacting with exosome associated non-coding transcripts and their interacting domains, could lead to a better understanding of not only cell to cell interactions but also the development of exosome targeted approaches in patient specific cell-based therapies. Keywords: Non-coding RNA, Extracellular RNA, Exosomes, Retroelement, Pseudogene

An Integration of the Restructured Melcor for the Midas Computer Code

International Nuclear Information System (INIS)

Sunhee Park; Dong Ha Kim; Ko-Ryu Kim; Song-Won Cho

2006-01-01

The developmental need for a localized severe accident analysis code is on the rise. KAERI is developing a severe accident code called MIDAS, which is based on MELCOR. In order to develop the localized code (MIDAS) which simulates a severe accident in a nuclear power plant, the existing data structure is reconstructed for all the packages in MELCOR, which uses pointer variables for data transfer between the packages. During this process, new features in FORTRAN90 such as a dynamic allocation are used for an improved data saving and transferring method. Hence the readability, maintainability and portability of the MIDAS code have been enhanced. After the package-wise restructuring, the newly converted packages are integrated together. Depending on the data usage in the package, two types of packages can be defined: some use their own data within the package (let's call them independent packages) and the others share their data with other packages (dependent packages). For the independent packages, the integration process is simple to link the already converted packages together. That is, the package-wise structuring does not require further conversion of variables for the integration process. For the dependent packages, extra conversion is necessary to link them together. As the package-wise restructuring converts only the corresponding package's variables, other variables defined from other packages are not touched and remain as it is. These variables are to be converted into the new types of variables simultaneously as well as the main variables in the corresponding package. Then these dependent packages are ready for integration. In order to check whether the integration process is working well, the results from the integrated version are verified against the package-wise restructured results. Steady state runs and station blackout sequences are tested and the major variables are found to be the same each other. In order to verify the results, the integrated

Packaging materials for plasma sterilization with the flowing afterglow of an N{sub 2}-O{sub 2} discharge: damage assessment and inactivation efficiency of enclosed bacterial spores

Energy Technology Data Exchange (ETDEWEB)

Levif, P; Moisan, M; Soum-Glaude, A [Groupe de Physique des Plasmas, Universite de Montreal, CP 6128, Succursale Centre-Ville, Montreal H3C 3J7, Quebec (Canada); Seguin, J; Barbeau, J, E-mail: michel.moisan@umontreal.ca [Faculte de Medecine Dentaire, Laboratoire de Controle des Infections, Universite de Montreal, CP 6128, Montreal H3C 3J7, Quebec (Canada)

2011-10-12

In conventional sterilization methods (steam, ozone, gaseous chemicals), after their proper cleaning, medical devices are wrapped/enclosed in adequate packaging materials, then closed/sealed before initiating the sterilization process: these packaging materials thus need to be porous. Gaseous plasma sterilization being still under development, evaluation and comparison of packaging materials have not yet been reported in the literature. To this end, we have subjected various porous packagings used with conventional sterilization systems to the N{sub 2}-O{sub 2} flowing afterglow and also a non-porous one to evaluate and compare their characteristics towards the inactivation of B. atrophaeus endospores deposited on a Petri dish and enclosed in such packagings. Because the sterilization process with the N{sub 2}-O{sub 2} discharge afterglow is conducted under reduced-pressure conditions, non-porous pouches can be sealed only after returning to atmospheric pressure. All the tests were therefore conducted with one end of the packaging freely opened, post-sealing being required. The features of these packaging materials, namely mass loss, resistance, toxicity to human cells as well as some characteristics specific to the plasma method used such as ultraviolet transparency, were examined before and after exposure to the flowing afterglow. All of our results show that the non-porous packaging considered is much more suitable than the conventionally used porous ones as far as ensuring an efficient and low-damage sterilization process with an N{sub 2}-O{sub 2} plasma-afterglow is concerned.

Validation study of the reactor physics lattice transport code WIMSD-5B by TRX and BAPL critical experiments of light water reactors

International Nuclear Information System (INIS)

Khan, M.J.H.; Alam, A.B.M.K.; Ahsan, M.H.; Mamun, K.A.A.; Islam, S.M.A.

2015-01-01

Highlights: • To validate the reactor physics lattice code WIMSD-5B by this analysis. • To model TRX and BAPL critical experiments using WIMSD-5B. • To compare the calculated results with experiment and MCNP results. • To rely on WIMSD-5B code for TRIGA calculations. - Abstract: The aim of this analysis is to validate the reactor physics lattice transport code WIMSD-5B by TRX (thermal reactor-one region lattice) and BAPL (Bettis Atomic Power Laboratory-one region lattice) critical experiments of light water reactors for neutronics analysis of 3 MW TRIGA Mark-II research reactor at AERE, Dhaka, Bangladesh. This analysis is achieved through the analysis of integral parameters of five light water reactor critical experiments TRX-1, TRX-2, BAPL-UO 2 -1, BAPL-UO 2 -2 and BAPL-UO 2 -3 based on evaluated nuclear data libraries JEFF-3.1 and ENDF/B-VII.1. In integral measurements, these experiments are considered as standard benchmark lattices for validating the reactor physics lattice transport code WIMSD-5B as well as evaluated nuclear data libraries. The integral parameters of the said critical experiments are calculated using the reactor physics lattice transport code WIMSD-5B. The calculated integral parameters are compared to the measured values as well as the earlier published MCNP results based on the Chinese evaluated nuclear data library CENDL-3.0 for assessment of deterministic calculation. It was found that the calculated integral parameters give mostly reasonable and globally consistent results with the experiment and the MCNP results. Besides, the group constants in WIMS format for the isotopes U-235 and U-238 between two data files have been compared using WIMS library utility code WILLIE and it was found that the group constants are well consistent with each other. Therefore, this analysis reveals the validation study of the reactor physics lattice transport code WIMSD-5B based on JEFF-3.1 and ENDF/B-VII.1 libraries and can also be essential to

The EQ3/6 software package for geochemical modeling: Current status

International Nuclear Information System (INIS)

Worlery, T.J.; Jackson, K.J.; Bourcier, W.L.; Bruton, C.J.; Viani, B.E.; Knauss, K.G.; Delany, J.M.

1988-07-01

EQ3/6 is a software package for modeling chemical and mineralogic interactions in aqueous geochemical systems. The major components of the package are EQ3NR (a speciation-solubility code), EQ6 (a reaction path code), EQLIB (a supporting library), and a supporting thermodynamic data base. EQ3NR calculates aqueous speciation and saturation indices from analytical data. It can also be used to calculate compositions of buffer solutions for use in laboratory experiments. EQ6 computes reaction path models of both equilibrium step processes and kinetic reaction processes. These models can be computed for closed systems and relatively simple open systems. EQ3/6 is useful in making purely theoretical calculations, in designing, interpreting, and extrapolating laboratory experiments, and in testing and developing submodels and supporting data used in these codes. The thermodynamic data base supports calculations over the range 0-300 degree C. 60 refs., 2 figs

The EQ3/6 software package for geochemical modeling: Current status

Energy Technology Data Exchange (ETDEWEB)

Wolery, T.J.; Jackson, K.J.; Bourcier, W.L.; Bruton, C.J.; Viani, B.E.; Knauss, K.G.; Delany, J.M.

1988-07-01

EQ3/6 is a software package for modeling chemical and mineralogic interactions in aqueous geochemical systems. The major components of the package are EQ3NR (a speciation-solubility code), EQ6 (a reaction path code), EQLIB (a supporting library), and a supporting thermodynamic data base. EQ3NR calculates aqueous speciation and saturation indices from analytical data. It can also be used to calculate compositions of buffer solutions for use in laboratory experiments. EQ6 computes reaction path models of both equilibrium step processes and kinetic reaction processes. These models can be computed for closed systems and relatively simple open systems. EQ3/6 is useful in making purely theoretical calculations, in designing, interpreting, and extrapolating laboratory experiments, and in testing and developing submodels and supporting data used in these codes. The thermodynamic data base supports calculations over the range 0-300{degree}C. 60 refs., 2 figs.

RAMONA-4B a computer code with three-dimensional neutron kinetics for BWR and SBWR system transient - user`s manual

Energy Technology Data Exchange (ETDEWEB)

Rohatgi, U.S.; Cheng, H.S.; Khan, H.J.; Mallen, A.N.; Neymotin, L.Y.

1998-03-01

This document is the User`s Manual for the Boiling Water Reactor (BWR), and Simplified Boiling Water Reactor (SBWR) systems transient code RAMONA-4B. The code uses a three-dimensional neutron-kinetics model coupled with a multichannel, nonequilibrium, drift-flux, phase-flow model of the thermal hydraulics of the reactor vessel. The code is designed to analyze a wide spectrum of BWR core and system transients. Chapter 1 gives an overview of the code`s capabilities and limitations; Chapter 2 describes the code`s structure, lists major subroutines, and discusses the computer requirements. Chapter 3 is on code, auxillary codes, and instructions for running RAMONA-4B on Sun SPARC and IBM Workstations. Chapter 4 contains component descriptions and detailed card-by-card input instructions. Chapter 5 provides samples of the tabulated output for the steady-state and transient calculations and discusses the plotting procedures for the steady-state and transient calculations. Three appendices contain important user and programmer information: lists of plot variables (Appendix A) listings of input deck for sample problem (Appendix B), and a description of the plotting program PAD (Appendix C). 24 refs., 18 figs., 11 tabs.

EQ3/6, a software package for geochemical modeling of aqueous systems: Package overview and installation guide (Version 7.0)

International Nuclear Information System (INIS)

Wolery, T.J.

1992-01-01

EQ3/6 is a software package for geochemical modeling of aqueous systems. This report describes version 7.0. The major components of the package include: EQ3NR, a speciation-solubility code; EQ6, a reaction path code which models water/rock interaction or fluid mixing in either a pure reaction progress mode or a time mode; EQPT, a data file preprocessor, EQLIB, a supporting software library; and five supporting thermodynamic data files. The software deals with the concepts of thermodynamic equilibrium, thermodynamic disequilibrium, and reaction kinetics. The five supporting data files contain both standard state and activity coefficient-related data. Three support the use of the Davies or B equations for the activity coefficients; the other two support the use of Pitzer's equations. The temperature range of the thermodynamic data on the data files varies from 25 degree C only to 0--300 degree C. EQPT takes a formatted data file (a data0 file) and writes an unformatted near-equivalent called a datal file, which is actually the form read by EQ3NR and EQ6. EQ3NR is useful for analyzing groundwater chemistry data, calculating solubility limits, and determining whether certain reactions are in states of partial equilibrium or disequilibrium. It is also required to initialize an EQ6 calculation. EQ6 models the consequences of reacting an aqueous solution with a set of reactants which react irreversibly. It can also model fluid mixing and the consequences of changes in temperature. This code operates both in a pure reaction progress frame and in a time frame

RAMONA-4B a computer code with three-dimensional neutron kinetics for BWR and SBWR system transient - user's manual

International Nuclear Information System (INIS)

Rohatgi, U.S.; Cheng, H.S.; Khan, H.J.; Mallen, A.N.; Neymotin, L.Y.

1998-03-01

This document is the User's Manual for the Boiling Water Reactor (BWR), and Simplified Boiling Water Reactor (SBWR) systems transient code RAMONA-4B. The code uses a three-dimensional neutron-kinetics model coupled with a multichannel, nonequilibrium, drift-flux, phase-flow model of the thermal hydraulics of the reactor vessel. The code is designed to analyze a wide spectrum of BWR core and system transients. Chapter 1 gives an overview of the code's capabilities and limitations; Chapter 2 describes the code's structure, lists major subroutines, and discusses the computer requirements. Chapter 3 is on code, auxillary codes, and instructions for running RAMONA-4B on Sun SPARC and IBM Workstations. Chapter 4 contains component descriptions and detailed card-by-card input instructions. Chapter 5 provides samples of the tabulated output for the steady-state and transient calculations and discusses the plotting procedures for the steady-state and transient calculations. Three appendices contain important user and programmer information: lists of plot variables (Appendix A) listings of input deck for sample problem (Appendix B), and a description of the plotting program PAD (Appendix C). 24 refs., 18 figs., 11 tabs

FEDGROUP-C 84 - An improved and modified CDC version of the program package for processing evaluated nuclear data in KEDAK, UKNDL and ENDF/B format

International Nuclear Information System (INIS)

Trkov, A.; Perdan, A.; Budnar, M.

1984-04-01

A CYBER version of the FEDGROUP-2 program system [INDC(HUN)-13/L+Sp, INDC(HUN)-15/L] has been developed. The principal inconsistencies of the original package were corrected. FEDGROUP-C 84 can be used for calculation of infinite dilution and resonance screened multigroup constants from evaluated library data in UKNDL, KEDAK and ENDF/B-IV, V formats. The package is intended for medium-sized computers. (author)

Progress toward NuPack, the ASME code for Type B containments

International Nuclear Information System (INIS)

Turula, P.

1995-01-01

This paper presented a brief status report on the development of an ASME Code Division for nuclear packaging and discussed some of the more interesting policy decisions as to what is and is not covered in terms of analytical methods, criteria, scope, and other aspects. The process of the development of this Division has been very slow and inconsistent. There were many participants with many diverse interests. The Division 3 rules are close to being ready to be issued. They are a compromise between many needs and the result is certainly not perfect. Opportunities for fine tuning and expanding this document will present themselves after it is issued as future needs become clear

Modernization and restructuring of realistic thermal hydraulic system analysis code, RELAP5/MOD3.3.1.2

International Nuclear Information System (INIS)

Chung, Bub Dong; Lee, Won Jae; Jeong, Jae Jun; Ha, Kwi Seok

1998-01-01

The code architecture entails the programming language and the code database. Various recent programming languages such as C, C ++ , Fortran 90, were considered as the candidate language for the modernization of RELAP5/MOD3.2.1.2. Among them, Fortran 90 was selected as a basic programming laguage for the modernization and restructuring of the code. Most of header file ( * .h) and equivalenced variables in RELAP5 have been replaced with members in the MODULE, which greatly enhance the code maintenance and readability. The FTB package is used for the dynamic memory management (DMM) of RELAP5. Although FTB DMM features are very successful, the use of FTB has been the obstacle in the maintenance of the code. It is difficult to understand and change the coding, and it requires a significant effort to find out index errors in large memory pools. With new features introduced in Fortran 90, it is possible to slove dynamic allocation problems within the standard features in an elegant, clear safe way. Each of FTB data blocks can be replaced by the suitably organized derived variables in MODULE and the standard DMM scheme. This DMM scheme provides the code flexibility which can save the memory requirements depending on the problem sizes without a extensive use of the complex FTB package. The current user's interface of the RELAP5 consists of a set of input file, output file, and restart/plot file. Many users complain that this interface is not user friendly. It was mainly caused by the text-oriented programming, namly console programming during the past many years. Now, windows programming has become popular in most areas of software development. Using this windows programming technique, the user friend freatures can be implemented. The Visual Fortran Quick Win run-time library helps to turn graphics programs into simple Windows applications. RELAP5 code has been re-compiled with the Quick Win feature, and the mask for user's dialog and graphical x-y plot were designed. This

VISUAL: a software package for plotting data in the RADHEAT-V4 code system

International Nuclear Information System (INIS)