Performance Evaluation of PCD Insert 1600 Grade on Turning of Al 6061 Reinforced with 7.5% ZrB2 Metal Matrix Composite

Directory of Open Access Journals (Sweden)

Ramanathan M.

2016-01-01

Full Text Available Aluminum matrix composite is the innovation of high performance material technology and it has superior interfacial integrity and thermodynamic stability between the matrix and reinforcement. Making the engineering components from this composite material require subsequent machining operations. This paper presents the detailed experimental investigation of the machining behaviour in turning of Al 6061-7.5% ZrB2 Metal Matrix Composite (MMC by using Poly Crystalline Diamond (PCD insert of 1600 grade. The effect of ZrB2 reinforcement particles on machinability behaviour need to be studied. It is concluded that the feed rate has great influence on surface roughness and depth of cut has great influence on cutting force. The confirmation experiment indicates that there is a good agreement between the estimated value and experimental Value. Tool wear study also carried out for time duration of 15 minutes.

Effect of the reinforced boron carbide particulate content of AA6061 alloy on formation of the passive film in seawater

International Nuclear Information System (INIS)

Katkar, V.A.; Gunasekaran, G.; Rao, A.G.; Koli, P.M.

2011-01-01

Highlights: → Presence of boron carbide increases the corrosion rate of A6061 alloy in seawater. → Increasing the B 4 C content decreases passive layer thickness. → Passive films formed on A6061 and its B 4 C composites are n-type semiconductors. - Abstract: The effect of boron carbide (B 4 C) reinforcement on the corrosion of AA6061 alloy was studied by investigating passive films formed in seawater. The higher passive current and its potential-dependence for these composites indicated formation of porous passive film. Electrochemical impedance spectroscopy (EIS) graph suggests that the alloy surface is partly or totally active. The formed passive film is n-type semiconductor junction in nature. The difference between corrosion potential (E corr ) and potential at zero charge (PZC) suggests that the chloride ions responsible for film breakdown exist within the passive film. A suitable mechanism is proposed for the passive film breakdown.

Selected mechanical properties of aluminum composite materials reinforced with SiC particles

Directory of Open Access Journals (Sweden)

A. Kurzawa

2008-07-01

Full Text Available This work presents the results of research concerning influence of ceramic particles’ content of silicon carbide on selected mechanical properties of type AW-AlCu4Mg2Mn - SiC composite materials. Composites produced of SiC particles with pressure infiltration method of porous preform and subject to hot plastic forming in the form of open die forging were investigated. The experimental samples contained from 5% up to 45% of reinforcing SiC particles of 8÷10μm diameter. Studies of strength properties demonstrated that the best results, in case of tensile strength as well as offset yield strength, might be obtained while applying reinforcement in the amount of 20-25% vol. of SiC. Application of higher than 25% vol. contents of reinforcing particles leads to gradual strength loss. The investigated composites were characterized by very high functional properties, such as hardness and abrasive wear resistance, whose values increase strongly with the increase of reinforcement amount. The presented results of the experiments shall allow for a more precise component selection of composite materials at the stage of planning and design of their properties.

Influence of extrusion parameters on sic distribution and properties of AA6061/SiC composites produced by kobo method

Energy Technology Data Exchange (ETDEWEB)

WoĨniak, Jarosáaw; Kostecki, Marek; Broniszewski, Kamil; Olszyna, Andrzej [Faculty of Material Science and Engineering, Warsaw University of Technology, Warsaw (Poland); Bochniak, Wáodzimierz [Faculty of Non-Ferrous Metals, AGH University of Science and Technology, Cracow (Poland)

2013-07-01

The influence of extrusion parameters on reinforcements distribution and properties of AA6061+x% vol. SiC p (x=0; 2.5; 5; 7.5; 10) composites was discussed in this paper The averages size of AA6061 and SiC particles were 10.6 μ m and 0.42 μ m, respectively. The composites were consolidated via powder metallurgy processing (without the sintering) and extruded by KoBo method. The microstructure was examined on each steps of production. High values of density for all produced composites were achieved. Additionally, hardness and Young’s modulus were investigated. The best reinforcement distribution and mechanical properties were obtained for composites extruded with the highest extrusion ratio. Key words: aluminum alloy, extrusion, aged hardening, metal matrix composites, microstructure.

Comportamiento en fluencia de un material compuesto de matriz metálica Al6061-15 vol % SiCw pulvimetalúrgico

Directory of Open Access Journals (Sweden)

González-Doncel, G.

2005-12-01

Full Text Available The creep behavior of a powder metallurgy (PM Al6061-15 vol % SiCw metal matrix composite has been studied. This behavior has been compared to that of 6061Al cast alloy and 6061Al PM alloy. The creep response of the PM unreinforced alloy is better than that of the cast 6061Al alloy. Similarly, the behavior of the composite is better than that of the PM unreinforced alloy. Two microstructural factors have been considered the responsible ones of this improvement. The first one is the dispersion of Al2O3 oxide particles of nanometric scale. The second one, is the presence of the SiC whisker reinforcement of micrometric scale. Despite the similar strengthening effect, the intrinsic nature of the reinforcing mechanism is, however, different for each type of particle due to the different microstructural scale.Se ha realizado un estudio de las propiedades en fluencia del material compuesto pulvimetalúrgico Al6061-15 vol % SiCw. Su comportamiento se ha comparado con el de la aleación Al6061 pulvimetalúrgica y la aleación Al6061 de colada. El comportamiento del material pulvimetalúrgico sin reforzar mejora respecto al del material de colada. Al mismo tiempo, el del material compuesto mejora respecto al comportamiento del material pulvimetalúrgico sin reforzar. Se consideran dos factores microestructurales como los principales responsables de la mejora de las propiedades en fluencia de este material compuesto. Por un lado, las partículas de Al2O3 de tamaño nanométrico y, por otro, las partículas de fibra corta cerámicas de SiC de tamaño micrométrico. Aunque ambos tipos de partículas dan lugar a un efecto de refuerzo similar, los mecanismos intrínsecos asociados a la presencia de estas partículas tienen una naturaleza diferente debido a la diferencia en la escala microestructural.

Failure behavior / characteristics of fabric reinforced polymer matrix composite and aluminum6061 on dynamic tensile loading

Energy Technology Data Exchange (ETDEWEB)

Bang, Hyejin; Cho, Chongdu [Inha University, Incheon (Korea, Republic of)

2017-08-15

Composite materials are composed of multiple types of materials as reinforcement and matrix. Among them, CFRP (Carbon fiber reinforced polymer) is widely used materials in automotive and defense industry. Carbon fibers are used as a reinforcement, of which Young's modulus is in a prepreg form. In automotive industry, especially, high strain rate test is needed to measure dynamic properties, used in dynamic analysis like high inertia included simulation as a car crash. In this paper, a SHTB (Split Hopkinson tensile bar) machine is employed for estimating stress-strain curve under dynamic load condition on aluminum 6061 and CFRP. The strain rate range is about from 100 /s to 1000 /s and the number of prepreg layers of composite specimen is total eight plies which are stacked symmetrically to structure CFRP. As a result, stress / strain point data are obtained and used for simulation into stacked composites.

Failure behavior / characteristics of fabric reinforced polymer matrix composite and aluminum6061 on dynamic tensile loading

International Nuclear Information System (INIS)

Bang, Hyejin; Cho, Chongdu

2017-01-01

Composite materials are composed of multiple types of materials as reinforcement and matrix. Among them, CFRP (Carbon fiber reinforced polymer) is widely used materials in automotive and defense industry. Carbon fibers are used as a reinforcement, of which Young's modulus is in a prepreg form. In automotive industry, especially, high strain rate test is needed to measure dynamic properties, used in dynamic analysis like high inertia included simulation as a car crash. In this paper, a SHTB (Split Hopkinson tensile bar) machine is employed for estimating stress-strain curve under dynamic load condition on aluminum 6061 and CFRP. The strain rate range is about from 100 /s to 1000 /s and the number of prepreg layers of composite specimen is total eight plies which are stacked symmetrically to structure CFRP. As a result, stress / strain point data are obtained and used for simulation into stacked composites.

A nano-indentation study on the mechanical behaviour of the matrix material in an AA6061-Al2O3 MMC

NARCIS (Netherlands)

Mussert, K.M.; Vellinga, W.P.; Bakker, A.; Zwaag, van der S.

2002-01-01

The nano-indentation technique is a suitable technique to measure hardness and elastic moduli profiles of AA6061 reinforced with Al2O3 particles, since it allows measurements of mechanical properties on a micrometer range. To investigate possible local variations in mechanical behaviour of the

Optimization of friction stir welding process parameters to maximize tensile strength of stir cast AA6061-T6/AlNp composite

International Nuclear Information System (INIS)

Ashok Kumar, B.; Murugan, N.

2014-01-01

Highlights: • AA6061/AlN p cast composite was welded by FSW process. • Regression models were developed to predict UTS and elongation of the FS welded joint. • FS welded joint using the optimized parameters exhibited maximum UTS and joint efficiency. • Defect free weld joint was obtained with optimized parameters value. - Abstract: Aluminium Matrix Composites (AMCs) reinforced with particulate form of reinforcement has replaced monolithic alloys in many engineering industries due to its superior mechanical properties and tailorable thermal and electrical properties. As aluminium nitride (AlN) has high specific strength, high thermal conductivity, high electrical resistivity, low dielectric constant, low coefficient of thermal expansion and good compatibility with aluminium alloy, Al/AlN composite is extensively used in electronic packaging industries. Joining of AMCs is unavoidable in many engineering applications. Friction Stir Welding (FSW) is one of the most suitable welding process to weld the AMCs reinforced with particulate form of ceramics without deteriorating its superior mechanical properties. An attempt has been made to develop regression models to predict the Ultimate Tensile Strength (UTS) and Percent Elongation (PE) of the friction stir welded AA6061 matrix composite reinforced with aluminium nitride particles (AlN p ) by correlating the significant parameters such as tool rotational speed, welding speed, axial force and percentage of AlN p reinforcement in the AA6061 matrix. Statistical software SYSTAT 12 and statistical tools such as analysis of variance (ANOVA) and student’s t test, have been used to validate the developed models. It was observed from the investigation that these factors independently influenced the UTS and PE of the friction stir welded composite joints. The developed regression models were optimized to maximize UTS of friction stir welded AA6061/AlN p composite joints

Corrosion performance of SiCsubp/6061 Al metal matrix composites in sodium chloride solution

International Nuclear Information System (INIS)

Mohmad Soib bin Selamat

1995-01-01

The corrosion performance of silicon carbide particle/aluminium metal matrix composites (SiCsubp/Al) were studied in sodium chloride solution by means of electrochemical, microscopic, gravimetric and analytical techniques. The materials under investigation were compocasting processed 6061 Al reinforced with increasing amounts of SiC particles. Potentiostatic polarization tests were done in 0.1M NaCl solutions that were aerated or deaerated to observe overall corrosion behaviour. It was seen that the corrosion potentials did not vary greatly in relation to the amounts of SiCsubp reinforcement. Corrosion tests showed that the degree of corrosion increased with increasing SiCsubp content. SEM analysis technique was used to study the corroded samples and the pitting morphology. By TEM, no intermetallic layer was found at SiC/Al interface. A model for pitting process was proposed

Electrochemical Corrosion Behaviour of Alumina-Al 6061 and Silicon Carbide-Al 6061 Metal-Matrix Composites

International Nuclear Information System (INIS)

Mohamed, K.E.; Gad, M.M.A.; El-Sayed, A.A.; Moustafa, O.H.

2001-01-01

The electrochemical corrosion behaviour of powder metallurgy-processed metal-matrix composites (MMCs)based on Al alloy 6061 reinforced with particulate Al 2 O 3 or Sic has been studied in chloride-containing environment. Also, the corrosion behaviour of the unrein forced Al 6061 produced by the same route investigated. Electrochemical tests were conducted on composites containing 10 and 20 vo l% of both reinforced particulates. Potentiodynamic polarization tests have been carried out in neutral as well as acidic and alkaline de-aerated 10 -3 M Na CI solution. In the neutral environment, the addition of Al 2 O 3 particulates was found to shift both the corrosion potential (E corr ) and the break down potential (E b ) slightly into the positive direction irrespective of the volume fraction added (10 and 20 vo l%). On the other hand , Sic caused a shift of E corr into the active site while the E b value was slightly ennobled. For both composites, the corrosion current values at the break down potentials were almost the same as the unrein forced alloy. In an attempt to further clarify the role of both particulate addition, cathodic polarization runs were conducted in both acidic (ph 3) and alkaline (ph 9)solutions for 20 vo l% of Al 2 O 3 and 20 vo l% Sic composite specimens. This indicated that cathodic current values for Sic composites were higher than those corresponding to the unrein forced alloy 6061, and those for the Al 2 O 3 composites were lower

Many particle approximation of the Aw-Rascle-Zhang second order model for vehicular traffic.

Science.gov (United States)

Francesco, Marco Di; Fagioli, Simone; Rosini, Massimiliano D

2017-02-01

We consider the follow-the-leader approximation of the Aw-Rascle-Zhang (ARZ) model for traffic flow in a multi population formulation. We prove rigorous convergence to weak solutions of the ARZ system in the many particle limit in presence of vacuum. The result is based on uniform BV estimates on the discrete particle velocity. We complement our result with numerical simulations of the particle method compared with some exact solutions to the Riemann problem of the ARZ system.

Artificial Neural Networks for the Prediction of Wear Properties of Al6061-TiO2 Composites

Science.gov (United States)

Veeresh Kumar, G. B.; Pramod, R.; Shivakumar Gouda, P. S.; Rao, C. S. P.

2017-08-01

The exceptional performance of composite materials in comparison with the monolithic materials have been extensively studied by researchers. Among the metal matrix composites Aluminium matrix based composites have displayed superior mechanical properties. The aluminium 6061 alloy has been used in aeronautical and automotive components, but their resistance against the wear is poor. To enhance the wear properties, Titanium dioxide (TiO2) particulates have been used as reinforcements. In the present investigation Back propagation (BP) technique has been adopted for Artificial Neural Network [ANN] modelling. The wear experimentations were carried out on a pin-on-disc wear monitoring apparatus. For conduction of wear tests ASTM G99 was adopted. Experimental design was carried out using Taguchi L27 orthogonal array. The sliding distance, weight percentage of the reinforcement material and applied load have a substantial influence on the height damage due to wear of the Al6061 and Al6061-TiO2 filled composites. The Al6061 with 3 wt% TiO2 composite displayed an excellent wear resistance in comparison with other composites investigated. A non-linear relationship between density, applied load, weight percentage of reinforcement, sliding distance and height decrease due to wear has been established using an artificial neural network. A good agreement has been observed between experimental and ANN model predicted results.

Effect of tool plunge depth on reinforcement particles distribution in surface composite fabrication via friction stir processing

Directory of Open Access Journals (Sweden)

Sandeep Rathee

2017-04-01

Full Text Available Aluminium matrix surface composites are gaining alluring role especially in aerospace, defence, and marine industries. Friction stir processing (FSP is a promising novel solid state technique for surface composites fabrication. In this study, AA6061/SiC surface composites were fabricated and the effect of tool plunge depth on pattern of reinforcement particles dispersion in metal matrix was investigated. Six varying tool plunge depths were chosen at constant levels of shoulder diameter and tool tilt angle to observe the exclusive effect of plunge variation. Process parameters chosen for the experimentation are speed of rotation, travel speed and tool tilt angle which were taken as 1400 rpm, 40 mm/min, and 2.5°respectively. Macro and the microstructural study were performed using stereo zoom and optical microscope respectively. Results reflected that lower plunge depth levels lead to insufficient heat generation and cavity formation towards the stir zone center. On the other hand, higher levels of plunge depth result in ejection of reinforcement particles and even sticking of material to tool shoulder. Thus, an optimal plunge depth is needed in developing defect free surface composites.

Mechanical Properties of SiC, Al2O3 Reinforced Aluminium 6061-T6 Hybrid Matrix Composite

Science.gov (United States)

Murugan, S. Senthil; Jegan, V.; Velmurugan, M.

2018-04-01

This paper contains the investigation of tensile, compression and impact characterization of SiC, Al2O3 reinforced Aluminium 6061-T6 matrix hybrid composite. Hybrid matrix composite fabrication was done by stir casting method. An attempt has been made by keeping Al2O3 percentage (7%) constant and increasing SiC percentage (10, 15, and 20%). After fabricating, the samples were prepared and tested to find out the various mechanical properties like tensile, compressive, and impact strength of the developed composites of different weight % of silicon carbide and Alumina in Aluminium alloy. The main objective of the study is to compare the values obtained and choose the best composition of the hybrid matrix composite from the mechanical properties point of view.

Comportamiento a fractura de la aleación 6061 reforzada con alúmina

Directory of Open Access Journals (Sweden)

Forn, A.

2004-04-01

Full Text Available The properties of the cast aluminium alloys 6061/(20%Al₂O_3p are studied. This material is obtained by Duralcan procedure after being submitted to an extrusion and forging process. These materials are submitted to T6 heat treatments in order to study their effect on mechanical properties. In this work the matrix characteristics are compared with the reinforced material in different production stages, using an optical and electronic microscopy, EDS, tensile, fatigue and ultramicrohardness tests. The mechanical properties indicate that the extruded reinforced material presents ultimate tensile strength values lower than the alloy 6061 under the same conditions, and this is related to the presence of spinel in the interface matrix-reinforcement. The fracture mechanisms are established by static and dynamic tensions in different cases, studying the possible interactions matrix-reinforcement and their repercussion in the mechanical behaviour of the alloy.

Se estudian las propiedades de las aleaciones de aluminio 6061/(20%Al₂O_3p obtenidas por colada y conformadas posteriormente por extrusión y forja. Estos materiales son sometidos a tratamientos térmicos de envejecimiento (T6 para estudiar su efecto en las propiedades mecánicas. En este trabajo se comparan las características de la matriz con las del material reforzado en las distintas etapas de producción utilizando técnicas de microscopía óptica y electrónica, EDS y ensayos de tracción, fatiga y ultramicroindentación. Los ensayos mecánicos indican que el material compuesto extruido presenta valores de resistencia mecánica más bajos que la aleación 6061 tratada en las mismas condiciones y ello se relaciona con la presencia de espinela en la interfase alúmina-matriz. Se establecen los mecanismos de fractura por tensiones estáticas y dinámicas en los distintos casos, estudiando las posibles interacciones matriz

Experimental processing and the effects of cenosphere on some mechanical properties of Al6061-SiC composites

Science.gov (United States)

Ashoka, E.; Sharanaprabhu, C. M.; Krishnaraja, G. Kodancha; Kudari, S. K.

2018-04-01

In this paper, stir casting technique was utilized to fabricate the hybrid Aluminium alloy (Al 6061) metal matrix reinforced with silicon carbide (SiC) and cenosphere particulates. An Al6061-SiC-Cenosphere hybrid composite is selected with 3wt% of silicon carbide and 3wt%, 6wt% and 9wt% proportions of cenosphere particulates. The uniform distribution of these two reinforcement particulates in Al6061matrix was achieved by stirring and pouring the hybrid composite mixture into the steel mould to accomplish the rectangular shaped casting. These various hybrid composites were studied with respect to its microstructure and some mechanical properties. The rectangular shaped casting of various hybrid composites was machined according to ASTM tensile specimens standards to estimate some mechanical properties. For various cast hybrid composites a comparative study is done with respect to modulus of elasticity, yield stress, percentage elongation and microhardness. Finally, the distribution of particulates and the nature of the tensile specimen fractured surface of various hybrid composites were understood using scanning electron microscope.

The effects of hard particles on the surface quality when micro-cutting aluminum 6061 T6

International Nuclear Information System (INIS)

Ding, X; Lee, L C; Butler, D L; Cheng, C K

2009-01-01

Studies of micro-cutting have so far largely been carried out on single-phase materials. Due to the size effect, the workpiece material microstructure can have a significant influence on the cutting force, chip formation and surface quality. Previous investigations have shown that hard particles in materials such as aluminum alloy can play a significant role in the generation of defects such as cracks and voids on the work surface. This paper will examine the extent of the problem during the micro-cutting of Al6061 T6 and propose how it can be mitigated

Dry Sliding Wear Charactristics of Aluminum 6061-T6, Magnesium AZ31 and Rock Dust Composite

Science.gov (United States)

Balachandar, R.; Balasundaram, R.; Rajkumar, G.

2018-02-01

In recent years, the use of aluminum composite is gaining popularity in a wide range of applications like automobiles, aerospace and constructions (both interior & exterior) panels etc., due to its high strength, low density characteristics. Various reinforcing materials are used with aluminum 6061-T6 in order to have better mechanical properties. The addition of 0.3% of magnesium AZ31 will increase the ultimate tensile strength by 25 %. The reinforcement of rock dust will decrease the density. Hence, in order to have an advantages of magnesium AZ31 and rock dust, in this work, these two constitutes are varied from 1% to 2% on the base material of Al6061-T6 in stir casting. To evaluate the wear characteristics, Pin on disc is used in these composites. The input parameters are speed, time & load. The output response is wear. To minimize the number of experiments, L9 orthogonal array is used. The test results showed that a composite of 97% of Al (6061-T6), 1% Mg (AZ31) & 2 % of rock dust produced less wear. To find the best value of operating parameter for each sample, ANN-GA is used.

Effect of heat treatment on friction and wear behavior of al-6061 composite reinforced with 10% submicron Al2O3 particles

International Nuclear Information System (INIS)

AlQutub, Amro M

2009-01-01

The present research aims at investigating experimentally the effect of heat treatment on the hardness, wear behavior, and friction properties of 6061 Al composite reinforced with sub-micron Al2O3 (10% vol.) produced by powder metallurgy. Heat treatment of the as-received composite starts by the solution treatment at a temperature of 550 degree C for a period of two hours followed by quenching in chilled water and then age hardening at 175 degree C for different periods. It is illustrated that heat treatment has relatively small effect on the hardness of the composite. This can be attributed to the large interface areas between the matrix and the sub-micron alumina in the composite, which reduces the whole concentration of vacancies in the matrix. The result is reduced efficiency of age hardening. For this reason, wear and friction tests were limited to the heat treated composite with four hours aging only. A pin-on-disc tribometer was used to conduct wear and friction tests against AISI 4140 at room temperature for both as-received composite and heat treated composite (with four hours of aging) for comparison. Wear tests indicate that heat treatment has the advantage of increasing transition load to severe wear by 30% compared to as-received composite. On the other hand, at high loads heat treatment results in larger delaminated flakes on the worn surface, indicating reduced fracture toughness. This, in turn, resulted in higher wear rates compared to the as-received composite. Dry friction coefficient is practically unaffected by the heat treatment. (author)

Strain change and creep behavior of STACIR/AW power line with heat exposure

Energy Technology Data Exchange (ETDEWEB)

Kim, B.G.; Park, S.D.; Kim, S.S.; Lee, H.W. [Overhead Conductor Research Lab., Korea Electrotechnology Research Inst., Changwon (Korea)

2005-07-01

As a way to expand electric capacity in power line with hovering of electric power demand, STACIR/AW (super thermal-resistant Al alloy conductors Al-clad Invar-reinforced) overhead conductor which cans double ampacity has been developed. The STACIR/AW power line is mechanically composite stranded wire composed of INVAR/AW stranded wire as core for sag control and heat-resistant aluminum alloy for delivering doubled electric current. Recently, in order to ensure stable line operation and to predict its span of life, the changes of thermal properties for STACIR/AW have been investigated. In the present work, the changes of strain with temperature and the creep behavior as important factors in sag control will be presented. The transition temperature of STACIR/AW 410 sqmm was estimated approximately 130 C and the creep rates were decreased with temperatures. (orig.)

Hot deformation behaviors and processing maps of B{sub 4}C/Al6061 neutron absorber composites

Energy Technology Data Exchange (ETDEWEB)

Li, Yu-Li [School of Materials Science and Engineering, Taiyuan University Of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Wang, Wen-Xian, E-mail: Wangwenxian@tyut.edu.cn [School of Materials Science and Engineering, Taiyuan University Of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Zhou, Jun [School of Materials Science and Engineering, Taiyuan University Of Technology, Taiyuan 030024 (China); Department of Mechanical Engineering, Pennsylvania State University Erie, The Behrend College, Erie, PA 16563 (United States); Chen, Hong-Sheng [School of Materials Science and Engineering, Taiyuan University Of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China)

2017-02-15

In this study, the hot deformation behaviors of 30 wt.% B{sub 4}C/Al6061 neutron absorber composites (NACs) have been investigated by conducting isothermal compression tests at temperatures ranging from 653 K to 803 K and strain rates from 0.01 to 10 s{sup −1}. It was found that, during hot compression, the B{sub 4}C/Al6061 NACs exhibited a steady flow characteristic which can be expressed by the Zener-Hollomon parameter as a hyperbolic-sine function of flow stress. High average activation energy (185.62 kJ/mol) of B{sub 4}C/Al6061 NACs is noted in current study owing to the high content of B{sub 4}C particle. The optimum hot working conditions for B{sub 4}C/Al6061 NACs are found to be 760–803 K/0.01–0.05 s{sup −1} based on processing map and microstructure evolution. Typical material instabilities are thought to be attributed to void formation, adiabatic shear bands (ASB), particle debonding, and matrix cracking. Finally, the effect of the plastic deformation zones (PDZs) on the microstructure evolution in this 30 wt.% B{sub 4}C/Al6061 composite is found to be very important. - Highlights: •The hot deformation behavior of the 30 wt.% B{sub 4}C/Al6061 NACs was first analyzed. •The 3D efficiency map and the instability map are developed. •The optimum hot working conditions were identified and validated by SEM and TEM. •The hot deformation schematic diagram of 30 wt.% B{sub 4}C/Al6061 NACs is developed.

Elastic Property Simulation of Nano-particle Reinforced Composites

Directory of Open Access Journals (Sweden)

He Jiawei

2016-01-01

Full Text Available A series of numerical micro-mechanical models for two kinds of particle (cylindrical and discal particle reinforced composites are developed to investigate the effect of microstructural parameters on the elastic properties of composites. The effects of both the degree of particle clustering and particle’s shape on the elastic mechanical properties of composites are investigated. In addition, single particle unit cell approximation is good enough for the analysis of the effect of averaged parameters when only linear elastic response is considered without considering the particle clustering in particle-reinforced composites.

Influence of volume percentage of NanoTiB2 particles on tribological & mechanical behaviour of 6061-T6 Al alloy nano-surface composite layer prepared via friction stir process

Directory of Open Access Journals (Sweden)

V. Kishan

2017-02-01

Full Text Available The aim of present study is to analyze the influence of volume percentage (vol.% of nano-sized particles (TiB2: average size is 35 nm on microstructure, mechanical and tribological behavior of 6061-T6 Al alloy surface nano composite prepared via Friction stir process (FSP. The microstructure of the fabricated surface nanocomposites is examined using optical microscopy (OM and scanning electron microscope (SEM for distribution of TiB2 nano reinforcement particles, thickness of nano composite layer formed on the Aluminum alloy substrate and fracture features. The depth of surface nano composite layer is measured as 3683.82 μm along the cross section of stir zone of nano composite perpendicular to FSP. It was observed that increase in volume percentage of TiB2 particles, the microhardness is increased up to 132 Hv and it is greater than as-received Al alloy's microhardness (104 Hv. It is also observed that at 4 volume percentage higher tensile properties exhibited as compared with the 2 and 8 vol. %. It is found that high wear resistance exhibited at 4 volume percentage as-compared with the 2 and 8 vol. %. The observed wear and mechanical properties are interrelated with microstructure, fractography and worn morphology.

Effects of ZrB{sub 2} on substructure and wear properties of laser melted in situ ZrB{sub 2p}/6061Al composites

Energy Technology Data Exchange (ETDEWEB)

Zeng, Yida [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Chao, Yuhjin [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); Department of Mechanical Engineering, University of South Carolina, Columbia, SC 29208 (United States); Luo, Zhen, E-mail: lz@tju.edu.cn [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Cai, Yangchuan [School of Material Science and Engineering, Tianjin University, Tianjin 300072 (China); State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China); Huang, Yongxian [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001 (China)

2016-03-01

Graphical abstract: - Highlights: • Laser beam partly disperses ZrB{sub 2} particle clusters and showing dispersed particles state after matrix solidification. • Laser melting process narrower cellular spacing in composites than AA6061 matrix. • Compared with matrix alloy, crystal orientation near melted layer edge of the composites is almost random duo to heterogeneous nucleation in melt and pinning effect of laser dispersed ZrB{sub 2} nanoparticles at solidification front. • Laser melted layer shows better wear properties than matrix and composite without laser melting. - Abstract: Aluminum matrix composites reinforced by in situ ZrB{sub 2} particles were successfully fabricated from an Al-KBF{sub 4}-K{sub 2}ZrF{sub 6} system via a direct melt reaction. A laser surface melting strategy is used to improve the surface strength of the in situ ZrB{sub 2p}/6061Al composite, which includes a series of laser-melted composites with different laser power processed by a 2 kW YAG laser generator. XRD and EDS results demonstrated the existence of ZrB{sub 2} nanoparticles in the composite. After laser melting, the penetration depth of the molten pool increases with increasing power density. OM and SEM analysis indicate that the laser melting process yields narrower cellular spacing of the matrix and partly disperses the ZrB{sub 2} particle clusters. Compared with laser-melted matrix alloys, the crystal orientations near the melted layers edge of the composite are almost random due to heterogeneous nucleation in the melt and the pinning effect of laser-dispersed ZrB{sub 2} nanoparticles at the solidification front. Wear test results show that the laser melted layer performs better at wear resistance than both the substrate and the matrix AA6061 by measuring wear mass loss. Compared with composite samples prepared without laser melting, the wear mass loss of the laser melted composites decreased from 61 to 56 mg under a load of 98 N for 60 min.

Wear Characterization of Aluminium/Basalt Fiber Reinforced Metal Matrix Composites - A Novel Material

Directory of Open Access Journals (Sweden)

P. Amuthakkannan

2017-06-01

Full Text Available Aluminum alloy based metal matrix composite participate have a wider applications in wear resistance applications. Attempt made in current study is that, basalt fiber reinforced aluminum metal matrix composite have been prepared using stir casting method. Different weight percentage of basalt fiber reinforced with Al (6061 metal matrix composites are used to study the wear resistance of the composites. For wear study, percentage of reinforcement, normal load and sliding velocity are the considered as important parameters. To study the effect of basalt fiber reinforcement on the dry sliding wear of Al6061 alloy composites the Pin On wear tester is used. Initially hardness of the composites was tested, it was found that increasing reinforcement in the composite hardness value of the composites also increased. Based on the Grey relation analysis (GRA the effects of wear resistance of the composites were studied.

RESEARCH OF FATIGUE AND MECHANICAL PROPERTIES AlMg1SiCu ALUMINIUM ALLOYS

Directory of Open Access Journals (Sweden)

Mária Mihaliková

2015-11-01

Full Text Available The paper is concerned with an analysis of utility and fatigue properties of industrially produced aluminium alloy, specifically EN AW 6061 (AlMg1SiCu, reinforced with the particles of SiC. The following properties were subject to evaluation: microstructure and sub-structure, mechanical characteristics. All of these mechanical properties in pre- and post- equal channel angular pressed (ECAP state have been studied. The hardness was evaluated by Vickers hardness test at the load of HV10. The significant part the thesis was devoted to the fatigue properties at cyclic load in torsion. The presented results demonstrate well that the combination of fractography and microscopy can give a significant contribution to the knowledge of initiation and propagation crack in the aluminium alloy.

Friction Stir Processing of Copper-Coated SiC Particulate-Reinforced Aluminum Matrix Composite

Directory of Open Access Journals (Sweden)

Chih-Wei Huang

2018-04-01

Full Text Available In the present work, we proposed a novel friction stir processing (FSP to produce a locally reinforced aluminum matrix composite (AMC by stirring copper-coated SiC particulate reinforcement into Al6061 alloy matrix. Electroless-plating process was applied to deposit the copper surface coating on the SiC particulate reinforcement for the purpose of improving the interfacial adhesion between SiC particles and Al matrix. The core-shell SiC structure provides a layer for the atomic diffusion between aluminum and copper to enhance the cohesion between reinforcing particles and matrix on one hand, the dispersion of fine copper in the Al matrix during FSP provides further dispersive strengthening and solid solution strengthening, on the other hand. Hardness distribution and tensile results across the stir zone validated the novel concept in improving the mechanical properties of AMC that was realized via FSP. Optical microscope (OM and Transmission Electron Microscopy (TEM investigations were conducted to investigate the microstructure. Energy dispersive spectrometer (EDS, electron probe micro-analyzer (EPMA, and X-ray diffraction (XRD were explored to analyze the atomic inter-diffusion and the formation of intermetallic at interface. The possible strengthening mechanisms of the AMC containing Cu-coated SiC particulate reinforcement were interpreted. The concept of strengthening developed in this work may open a new way of fabricating of particulate reinforced metal matrix composites.

Application of full factorial design to study the tribological properties of AA6061-B4C and AA6061-B4C-MoS2 composites

Directory of Open Access Journals (Sweden)

Monikandan V. V.

2018-03-01

Full Text Available This study statistically analyzes the tribological properties of AA6061-10 wt. % B4C mono composite and AA6061-10 wt.% B4C-7.5 wt. % MoS2 hybrid composite. The tribological behavior of the composites was studied at atmospheric conditions using a pin-on-disk tribo-tester. The tribological experiments were conducted as per the full factorial design (FFD experimental scheme. The ANOVA analysis of the wear rate revealed that the three factors, A (MoS2 particles addition, B (applied load, and D (sliding distance presented the physical and statistical significance on the wear rate. The ANOVA analysis of the friction coefficient revealed that the factors B (applied load and C (sliding speed and interaction AB (interaction of MoS2 particles addition and applied load presented the physical and statistical significance on the friction coefficient. It is observed from the main effects plots of the wear rate and friction coefficient that the increase in the levels of factors B (applied load and D (sliding distance increased the wear rate and friction coefficient. However, the wear rate and friction coefficient decreased with the increase in the level of factor A (MoS2 particles addition.

Desarrollo y caracterización de un material compuesto de matriz de aluminio 6061 y partículas de TiB2

Directory of Open Access Journals (Sweden)

Plaza, L. M.

2010-12-01

Full Text Available The incorporation of ceramic particles has been one of the ways developed to improve the mechanical properties of aluminium alloys during the last years. The main objective of this work has been to develop the manufacturing process of the reinforced aluminium alloy and analyse its mechanical properties and microstructure. Details about an innovative MMC manufacturing process and the results obtained in the development of a new family of TiB2- reinforced aluminium alloys for forging and extrusion applications are presented. It has been observed that the considered manufacturing process, consisting in the fabrication of particles by SHS and their incorporation into the selected alloy, is a feasible process to manufacture reinforced alloys that can be subsequently extruded or forged. The final result is the development of a material suitable for extrusion and forging applications and that presents an improvement of fatigue and tensile properties of the matrix alloy.Una de las vías desarrolladas, en los últimos años, para la mejora de las propiedades mecánicas de las aleaciones de aluminio es la de la incorporación de refuerzos cerámicos en forma de partículas cerámicas. El objetivo principal del trabajo ha sido desarrollar el proceso de fabricación de una aleación de aluminio 6061 reforzada con partículas de diboruro de titanio, TiB2, y analizar las propiedades del material obtenido. Se ha observado que el proceso de fabricación planteado, consistente en la fabricación de las partículas por medio del proceso de síntesis autopropagada a alta temperatura SHS (Self propagating high temperature synthesis y su posterior incorporación a la aleación 6061, es un proceso viable para la fabricación de aleaciones reforzadas adecuadas para la realización de procesos subsiguientes de extrusión o forja. El resultado final es la obtención de un material adecuado para la fabricación de componentes extruidos y que presenta una mejora de sus

Microstructure and wear characterization of aluminum matrix composites reinforced with industrial waste fly ash particulates synthesized by friction stir processing

Energy Technology Data Exchange (ETDEWEB)

Dinaharan, I., E-mail: dinaweld2009@gmail.com [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa); Nelson, R., E-mail: nelson.90.mech@gmail.com [Department of Mechanical Engineering, Karunya University, Coimbatore 641114, Tamil Nadu (India); Vijay, S.J., E-mail: vijayjoseph.2001@gmail.com [Center for Research in Metallurgy, School of Mechanical Sciences, Karunya University, Coimbatore 641114, Tamil Nadu (India); Akinlabi, E.T., E-mail: etakinlabi@uj.ac.za [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa)

2016-08-15

Fly ash (FA) is a waste product of coal combustion in thermal power plants which is available in massive quantities all over the world causing land pollution. This paper reports the characterization of AA6061 aluminum matrix composites (AMCs) reinforced with FA particles synthesized using friction stir processing (FSP). The volume fraction of FA particles was varied from 0 to 18 in steps of 6. The prepared AMCs were characterized using optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diagram (EBSD). The wear rate was estimated using a pin-on-disc wear apparatus. FA particles were observed to be distributed homogeneously in the AMC irrespective of the location within the stir zone. The EBSD micrographs revealed remarkable grain refinement in the AMC. The incorporation of FA particles enhanced the microhardness and wear resistance of the AMC. The strengthening mechanisms of the AMC were discussed and correlated to the observed microstructures. The wear mechanisms were identified by characterizing the wear debris and worn surfaces. - Highlights: •Industrial waste fly ash was used to produce aluminum matrix composites. •Friction stir processing was used to produce AA6061/Fly Ash composite. •Fly ash particles refined the grains of aluminum matrix. •Fly ash particles enhanced the hardness and wear resistance. •Successful utilization of fly ash to make aluminum composites reduces land pollution.

[Use of the Pentax-AWS videolaryngoscope for bougie-assisted exchange of tracheal tubes].

Science.gov (United States)

Kishii, Miki; Asai, Takashi; Nagata, Atsushi; Shingu, Koh

2009-06-01

A gum elastic bougie can be useful for tube exchange. One major problem with this technique is that it may not possible to pass a new tube over the bougie into the trachea, because the tip of the tube can collide with tissues around the glottis. We report a case in which tube exchange using the bougie was difficult, but the Pentax-AWS videolaryngoscope enabled tracheal intubation. In a 62-year-old trauma patient with head and neck stabilized using a Halo vest, was scheduled for emergency fixation of the neck. Exchange of a polyvinylchloride tube to a reinforced tube was planned. A bougie was passed through the old tube, removing the tube, and a new tube was advanced over the bougie, but it was impossible to advance the tube into the trachea. Insertion of a Macintosh laryngoscope did not enable intubation. The new tube was removed from the bougie, attached to the Pentax-AWS videolaryngoscope, and the tube (with the Pentax-AWS) was passed over the bougie. Although it was not possible to see the glottis with the Pentax-AWS, the tube was easily advanced over the bougie into the trachea. Operation went on uneventfully. We believe that, when it is difficult to advance a tracheal tube over a tube exchanger, the use of the Pentax-AWS may facilitate intubation.

Long term immersion test of aluminum alloy AA 6061 used for fuel cladding in MTR type reactors

International Nuclear Information System (INIS)

Linardi, Evelina M.; Rodriguez, Sebastian; Haddad, Roberto; Lanzani, Liliana

2009-01-01

In this work we present the results of long term immersion tests performed in the aluminum alloy AA 6061, used for fuel cladding in MTR type reactors. The tests were performed at open circuit potential in high purity water (ρ = 18.2 MΩ.cm) and in 10 -3 M NaCl solution. Two kinds of assemblies were studied: simple sheets and artificial crevices, immersed during 6, 12 and 18 months at room temperature. In both media and both assemblies, the aluminum hydroxide phases crystalline bayerite and bohemite were identified. It was found that a kind of localized attack named alkaline attack occurs around the iron-rich intermetallics. These particles were confirmed to control the corrosion of the AA 6061 alloy in an aerated medium. Immersion times for up to 18 months did not increase the oxide growth or the alkaline attack on the AA 6061 alloy. (author)

Tensile flow stress of ceramic particle-reinforced metal in the presence of particle cracking

Energy Technology Data Exchange (ETDEWEB)

Mueller, R. [Ecole Polytechnique Federale de Lausanne (EPFL), Laboratory for Mechanical Metallurgy, CH-1015 Lausanne (Switzerland); Rossoll, A. [Ecole Polytechnique Federale de Lausanne (EPFL), Laboratory for Mechanical Metallurgy, CH-1015 Lausanne (Switzerland)], E-mail: andreas.rossoll@epfl.ch; Weber, L. [Ecole Polytechnique Federale de Lausanne (EPFL), Laboratory for Mechanical Metallurgy, CH-1015 Lausanne (Switzerland); Bourke, M.A.M. [Los Alamos National Laboratory (LANL), LANSCE-12, P.O. Box 1663, MS H805, Los Alamos, NM 87545 (United States); Dunand, D.C. [Northwestern University, Department of Materials Science and Engineering, Evanston, IL 60208 (United States); Mortensen, A. [Ecole Polytechnique Federale de Lausanne (EPFL), Laboratory for Mechanical Metallurgy, CH-1015 Lausanne (Switzerland)

2008-10-15

A simplified model is proposed to quantify the effect of damage in the form of particle cracking on the elastic and plastic behaviour of particle-reinforced metal matrix composites under uniaxial tensile loading: cracked particles are simply replaced, in a mean-field model, with as much matrix. Pure aluminium reinforced with 44 vol.% alumina particles, tested in tension and unloaded at periodic plastic deformations, is analysed by neutron diffraction during each reloading elastic step, at 30%, 50%, 70% and 90% of the tensile flow stress. The data give the evolution of the elastic matrix strains in the composite and also measure the progress of internal damage by particle cracking. The test gives (i) the evolution of the in situ matrix flow stress, and (ii) the evolution of load partitioning during elastic deformation with increasing composite damage. Predictions of the present model compare favourably with relevant results in the literature, and with results from the present neutron diffraction experiments.

Tensile flow stress of ceramic particle-reinforced metal in the presence of particle cracking

International Nuclear Information System (INIS)

Mueller, R.; Rossoll, A.; Weber, L.; Bourke, M.A.M.; Dunand, D.C.; Mortensen, A.

2008-01-01

A simplified model is proposed to quantify the effect of damage in the form of particle cracking on the elastic and plastic behaviour of particle-reinforced metal matrix composites under uniaxial tensile loading: cracked particles are simply replaced, in a mean-field model, with as much matrix. Pure aluminium reinforced with 44 vol.% alumina particles, tested in tension and unloaded at periodic plastic deformations, is analysed by neutron diffraction during each reloading elastic step, at 30%, 50%, 70% and 90% of the tensile flow stress. The data give the evolution of the elastic matrix strains in the composite and also measure the progress of internal damage by particle cracking. The test gives (i) the evolution of the in situ matrix flow stress, and (ii) the evolution of load partitioning during elastic deformation with increasing composite damage. Predictions of the present model compare favourably with relevant results in the literature, and with results from the present neutron diffraction experiments

AWS development essentials

CERN Document Server

Kuppusamy, Prabhakaran

2014-01-01

This book is intended for expert programmers and architects who want to learn how to migrate the existing infrastructure to AWS Cloud and start using AWS services in all application tiers. Basic knowledge of Java and competence in cloud computing will be needed to follow the examples in this book.

Reinforcement architectures and thermal fatigue in diamond particle-reinforced aluminum

Energy Technology Data Exchange (ETDEWEB)

Schoebel, M., E-mail: michaels@mail.tuwien.ac.at [Institute of Materials Science and Technology, Vienna University of Technology, Karlsplatz 13, A-1040 Vienna (Austria); Degischer, H.P. [Institute of Materials Science and Technology, Vienna University of Technology, Karlsplatz 13, A-1040 Vienna (Austria); Vaucher, S. [Advanced Materials Processing, EMPA - Swiss Federal Laboratories for Materials Science and Technology, Feuerwerkstrasse 39, CH-3602 Thun (Switzerland); Hofmann, M. [Forschungsneutronenquelle Heinz Maier-Leibnitz, Lichtenbergstrasse 1, D-85747 Garching (Germany); Cloetens, P. [European Synchrotron Radiation Facility, 6 Rue Jules Horowitz, F-38043 Grenoble (France)

2010-11-15

Aluminum reinforced by 60 vol.% diamond particles has been investigated as a potential heat sink material for high power electronics. Diamond (CD) is used as reinforcement contributing its high thermal conductivity (TC {approx} 1000 W mK{sup -1}) and low coefficient thermal expansion (CTE {approx} 1 ppm K{sup -1}). An Al matrix enables shaping and joining of the composite components. Interface bonding is improved by limited carbide formation induced by heat treatment and even more by SiC coating of diamond particles. An AlSi7 matrix forms an interpenetrating composite three-dimensional (3D) network of diamond particles linked by Si bridges percolated by a ductile {alpha}-Al matrix. Internal stresses are generated during temperature changes due to the CTE mismatch of the constituents. The stress evolution was determined in situ by neutron diffraction during thermal cycling between room temperature and 350 deg. C (soldering temperature). Tensile stresses build up in the Al/CD composites: during cooling <100 MPa in a pure Al matrix, but around 200 MPa in the Al in an AlSi7 matrix. Compressive stresses build up in Al during heating of the composite. The stress evolution causes changes in the void volume fraction and interface debonding by visco-plastic deformation of the Al matrix. Thermal fatigue damage has been revealed by high resolution synchrotron tomography. An interconnected diamond-Si 3D network formed with an AlSi7 matrix promises higher stability with respect to cycling temperature exposure.

Experimental investigation of effect of specimen thickness on fracture toughness of Al-TiC composites

Directory of Open Access Journals (Sweden)

M. S. Raviraj

2016-07-01

Full Text Available In this paper, the macro and micro-mechanical fracture behavior was studied for aluminum (Al6061 alloy matrix, reinforced with various proportions of TiC particles such as 3wt%, 5wt% and 7wt%. The Al6061-TiC metal matrix composites were produced by stir casting method to ensure uniform distribution of the TiC particulates in the Al matrix. The compact tension (CT specimens were machined according to ASTM E399 specifications to evaluate the fracture toughness for Al6061-TiC metal matrix composites. The CT specimens were machined for crack to width (a/W ratio of 0.5 and thickness to width (B/W ratios of 0.2 to 0.7 with an increment of 0.1. Load versus crack mouth opening displacement (CMOD data was plotted to estimate stress intensity factor KQ for various thicknesses of the specimen. The fracture toughness KIC was obtained by plotting stress intensity factor versus thickness to width ratios of specimen data. The fracture toughness of these composites varied between 16.4-19.2 MPa√m. Scanning Electron Microscope (SEM studies was made on the fractured surface of the specimens to understand the micro-mechanisms of failure involved in these composites. Void initiation is more significant in the matrix near the interface. The micro-cracks grow from these micro-voids and crack propagates by linking these micro cracks locating the crack path preferentially in the matrix adjacent to the interface indicating ductile fracture.

Evaluation of interfacial bonding in dissimilar materials of YSZ-alumina composites to 6061 aluminium alloy using friction welding

International Nuclear Information System (INIS)

Uday, M.B.; Ahmad Fauzi, M.N.; Zuhailawati, H.; Ismail, A.B.

2011-01-01

Research highlights: → Friction-welding process. → Joining between ceramic composite and metal alloy. → Slip casting of the yttria stabilized zirconia/alumina composite samples. - Abstract: The interfacial microstructures characteristics of alumina ceramic body reinforced with yttria stabilized zirconia (YSZ) was evaluated after friction welding to 6061 aluminum alloy using optical and electron microscopy. Alumina rods containing 25 and 50 wt% yttria stabilized zirconia were fabricated by slip casting in plaster of Paris (POP) molds and subsequently sintered at 1600 deg. C. On the other hand, aluminum rods were machine down to the required dimension using a lathe machine. The diameter of the ceramic and the metal rods was 16 mm. Rotational speeds for the friction welding were varied between 900 and 1800 rpm. The friction pressure was maintained at 7 MPa for a friction time of 30 s. Optical and scanning electron microscopy was used to analyze the microstructure of the resultant joints, particularly at the interface. The joints were also examined with EDX line (energy dispersive X-ray) in order to determine the phases formed during the welding. The mechanical properties of the friction welded YSZ-Al 2 O 3 composite to 6061 alloy were determined with a four-point bend test and Vickers microhardness. The experimental results showed the degree of deformation varied significantly for the 6061 Al alloy than the ceramic composite part. The mechanical strength of friction-welded ceramic composite/6061 Al alloy components were obviously affected by joining rotational speed selected which decreases in strength with increasing rotational speed.

Effect of type and percentage of reinforcement for optimization of the cutting force in turning of Aluminium matrix nanocomposites using response surface methodologies

Energy Technology Data Exchange (ETDEWEB)

Priyadarshi, Devinder [DAV Institute of Engineering and Technology, Jalandhar (India); Sharma, Rajesh Kumar [Institute of Technology, Hamirpur (India)

2016-03-15

Aluminium matrix composites (AMCs) now hold a significant share of raw materials in many applications. It is of prime importance to study the machinability of such composites so as to enhance their applicability. Sufficient work has been done for studying the machining of AMCs with particle reinforcements of micron range. This paper presents the study of AMCs with particle reinforcement of under micron range i.e. nanoparticles. This paper brings out the results of an experimental investigation of type and weight percent of nanoparticles on the tangential cutting force during turning operation. SiC, Gr and SiC-Gr (in equal proportions) were used with Al-6061 alloy as the matrix phase. The results indicate that composites with SiC require greater cutting force followed by hybrid and then Gr. Increase in the weight percent also significantly affected the magnitude of cutting force. RSM was used first to design and analyze the experiments and then to optimize the turning process and obtain optimal conditions of weight and type of reinforcements for turning operation.

Equal channel angular pressing of powder processed Al6061/SiC nano metal matrix composites and study of its wear properties

Science.gov (United States)

Bongale, Arunkumar M.; Kumar, Satish

2018-03-01

Nano Metal Matrix Composites were fabricated by a novel approach by combining powder metallurgy and equal channel angular pressing (ECAP) using aluminium alloy 6061 (Al6061) as matrix phase and 2, 4 and 6 wt% of silicon carbide nanoparticles (SiCnp) as reinforcements. Alloying elements of Al6061 in their elemental form are blended together using high energy planetary ball mill and calculated wt% of SiCnp were mixed with it. Thus formed composite powder mixture is compacted in a uniaxial compaction die and then subjected to ECAP up to three passes. Density and porosity of samples were estimated using Archimedes’ principle. Pin on disc setup is used to evaluate the wear properties of the composites under different speed and loading conditions. Tests revealed that increase in wt% of SiCnp reduces the wear rate of the composites whereas increasing the load and speed increases wear rate of the composite samples. SEM micrographs of worn surfaces indicated different types of wear mechanism responsible for wear of the specimens under different testing conditions. Also, wt% of SiCnp and the number of passes through ECAP were found to increase the hardness value of the composite material.

Composite material reinforced with atomized quasicrystalline particles and method of making same

Science.gov (United States)

Biner, S.B.; Sordelet, D.J.; Lograsso, B.K.; Anderson, I.E.

1998-12-22

A composite material comprises an aluminum or aluminum alloy matrix having generally spherical, atomized quasicrystalline aluminum-transition metal alloy reinforcement particles disposed in the matrix to improve mechanical properties. A composite article can be made by consolidating generally spherical, atomized quasicrystalline aluminum-transition metal alloy particles and aluminum or aluminum alloy particles to form a body that is cold and/or hot reduced to form composite products, such as composite plate or sheet, with interfacial bonding between the quasicrystalline particles and the aluminum or aluminum alloy matrix without damage (e.g. cracking or shape change) of the reinforcement particles. The cold and/or hot worked composite exhibits substantially improved yield strength, tensile strength, Young`s modulus (stiffness). 3 figs.

Enhancement in the microstructure and neutron shielding efficiency of sandwich type of 6061Al–B4C composite material via hot isostatic pressing

International Nuclear Information System (INIS)

Park, Jin-Ju; Hong, Sung-Mo; Lee, Min-Ku; Rhee, Chang-Kyu; Rhee, Won-Hyuk

2015-01-01

Highlights: • 6061Al–B 4 C neutron shielding composites are fabricated by sintering and HIP. • HIP process improves the wettability of B 4 C particles into 6061Al matrix. • Neutron attenuation performance can be enhanced by application of HIP process. - Abstract: Sandwich type of 6061Al–B 4 C composite plates, which are used as a thermal neutron absorber for spent nuclear fuel pool storage rack, were fabricated using two different consolidation ways as sintering and hot isostatic pressing (HIP) processes and their thermal neutron shielding efficiency was investigated as a function of B 4 C concentration ranging from 0 to 40 wt.%. For this purpose, two respective inner core compaction parts of sintered and HIPped neutron absorbing composite materials were first produced and then cladded them between two outer plates by HIP process. The application of HIP process provided not only a lead of excellent interfacial adhesion due to the improved wettability but also an enhancement of thermal neutron shielding efficiency owing to the more uniform dispersion of B 4 C particles

Effects of Particle Size on the Shear Behavior of Coarse Grained Soils Reinforced with Geogrid.

Science.gov (United States)

Kim, Daehyeon; Ha, Sungwoo

2014-02-07

In order to design civil structures that are supported by soils, the shear strength parameters of soils are required. Due to the large particle size of coarse-grained soils, large direct shear tests should be performed. In this study, large direct shear tests on three types of coarse grained soils (4.5 mm, 7.9 mm, and 15.9 mm) were performed to evaluate the effects of particle size on the shear behavior of coarse grained soils with/without geogrid reinforcements. Based on the direct shear test results, it was found that, in the case of no-reinforcement, the larger the maximum particle size became, the larger the friction angle was. Compared with the no-reinforcement case, the cases reinforced with either soft geogrid or stiff geogrid have smaller friction angles. The cohesion of the soil reinforced with stiff geogrid was larger than that of the soil reinforced with soft geogrid. The difference in the shear strength occurs because the case with a stiff geogrid has more soil to geogrid contact area, leading to the reduction in interlocking between soil particles.

Reinforced magnesium composites by metallic particles for biomedical applications

Energy Technology Data Exchange (ETDEWEB)

Vahid, Alireza; Hodgson, Peter [Institute for Frontier Materials, Deakin University, Geelong, Victoria 3217 (Australia); Li, Yuncang, E-mail: yuncang.li@rmit.edu.au [Institute for Frontier Materials, Deakin University, Geelong, Victoria 3217 (Australia); School of Engineering, RMIT University, Melbourne, Victoria 3001 (Australia)

2017-02-08

Pure magnesium (Mg) implants have unsatisfactory mechanical properties, particularly in loadbearing applications. Particulate-reinforced Mg composites are known as promising materials to provide higher strength implants compared to unreinforced metals. In the current work biocompatible niobium (Nb) and tantalum (Ta) particles are selected as reinforcement, and Mg-Nb and Mg-Ta composites fabricated via a powder metallurgy process associated with the ball milling technique. The effect of Nb and Ta contents on the microstructure and mechanical properties of Mg matrix was investigated. There was a uniform distribution of reinforcements in the Mg matrix with reasonable integrity and no intermetallic formation. The compressive mechanical properties of composites vary with reinforcement contents. The optimal parameters to fabricate biocompatible Mg composites and the optimal composition with appropriate strength, hardness and ductility are recommended.

Microstructure and hardness of WC-Co particle reinforced iron matrix surface composite

Directory of Open Access Journals (Sweden)

Zhang Peng

2013-11-01

Full Text Available In this study, a high Cr cast iron surface composite material reinforced with WC-Co particles 2-6 mm in size was prepared using a pressureless sand mold infiltration casting technique. The composition, microstructure and hardness were determined by means of energy dispersive spectrometry (EDS, electron probe microanalysis (EPMA, scanning electron microscope (SEM and Rockwell hardness measurements. It is determined that the obtained composite layer is about 15 mm thick with a WC-Co particle volumetric fraction of ~38%. During solidification, interface reaction takes place between WC-Co particles and high chromium cast iron. Melting and dissolving of prefabricated particles are also found, suggesting that local Co melting and diffusion play an important role in promoting interface metallurgical bonding. The composite layer is composed of ferrite and a series of carbides, such as (Cr, W, Fe23C6, WC, W2C, M6C and M12C. The inhomogeneous hardness in the obtained composite material shows a gradient decrease from the particle reinforced metal matrix composite layer to the matrix layer. The maximum hardness of 86.3 HRA (69.5 HRC is obtained on the particle reinforced surface, strongly indicating that the composite can be used as wear resistant material.

Effects of Particle Size on the Shear Behavior of Coarse Grained Soils Reinforced with Geogrid

Directory of Open Access Journals (Sweden)

Daehyeon Kim

2014-02-01

Full Text Available In order to design civil structures that are supported by soils, the shear strength parameters of soils are required. Due to the large particle size of coarse-grained soils, large direct shear tests should be performed. In this study, large direct shear tests on three types of coarse grained soils (4.5 mm, 7.9 mm, and 15.9 mm were performed to evaluate the effects of particle size on the shear behavior of coarse grained soils with/without geogrid reinforcements. Based on the direct shear test results, it was found that, in the case of no-reinforcement, the larger the maximum particle size became, the larger the friction angle was. Compared with the no-reinforcement case, the cases reinforced with either soft geogrid or stiff geogrid have smaller friction angles. The cohesion of the soil reinforced with stiff geogrid was larger than that of the soil reinforced with soft geogrid. The difference in the shear strength occurs because the case with a stiff geogrid has more soil to geogrid contact area, leading to the reduction in interlocking between soil particles.

Silver matrix composites reinforced with galvanically silvered particles

OpenAIRE

J. Śleziona; J. Wieczorek,

2007-01-01

Purpose: The paper presents the possibility of the application of metalic layers drifted with the use of the galvanic methods on the ceramic particles surface. The application of the layers was aimed at obtaining the rewetting of the reinforcing particles with the liquid silver in the course of the producing of silver matrix composites with the use of mechanical stirring method. To enable introducing of the iron powder and glass carbon powder to liquid silver the solution of covering the powd...

Effect of sintering temperatures on titanium matrix composites reinforced by ceramic particles

Energy Technology Data Exchange (ETDEWEB)

Romero, F.; Amigo, V.; Busquets, D.; Klyatskina, E. [Mechanical and Materials Engineering Department. Polytechnical University of Valencia, Valencia (Spain)

2005-07-01

Titanium and titanium composites have a potential use in aerospace and biotechnology industries, and nowadays in others like sports and fashion ones. In this work composite materials, based on titanium matrix reinforced with ceramic particles, have been developed. PM route is used to obtain compact and sintered samples. TiN and TiAl powders, are milled with Ti powder in different volumetric percentages in a ball mill. These mixtures are pressed in a uniaxial press and sintered in a vacuum furnace at different temperatures between 1180 to 1220 deg. C. Porosity of samples is analysed, before and after the sintering process, by Archimedes technique and by image analysis. Mechanical properties and the reinforcement particles influence in the titanium matrix are studied by flexion test in green and sintered states, and by hardness and microhardness tests. Complimentarily, a microstructural analysis is carried out by optical and electron microscopy, and the reactivity between the reinforce particles and titanium matrix are studied. (authors)

The Particle Shape of WC Governing the Fracture Mechanism of Particle Reinforced Iron Matrix Composites.

Science.gov (United States)

Li, Zulai; Wang, Pengfei; Shan, Quan; Jiang, Yehua; Wei, He; Tan, Jun

2018-06-11

In this work, tungsten carbide particles (WC p , spherical and irregular particles)-reinforced iron matrix composites were manufactured utilizing a liquid sintering technique. The mechanical properties and the fracture mechanism of WC p /iron matrix composites were investigated theoretically and experimentally. The crack schematic diagram and fracture simulation diagram of WC p /iron matrix composites were summarized, indicating that the micro-crack was initiated both from the interface for spherical and irregular WC p /iron matrix composites. However, irregular WC p had a tendency to form spherical WC p . The micro-cracks then expanded to a wide macro-crack at the interface, leading to a final failure of the composites. In comparison with the spherical WC p , the irregular WC p were prone to break due to the stress concentration resulting in being prone to generating brittle cracking. The study on the fracture mechanisms of WC p /iron matrix composites might provide a theoretical guidance for the design and engineering application of particle reinforced composites.

Study by three techniques of the elastic response of Al(6061) matrix composite material with a high content (40 % vol) of SIC; Estudio mediante tres tecnicas del modulo elastico de un material compuesto de Al(6061) con un alto contenido (40%vol) de SiC

Energy Technology Data Exchange (ETDEWEB)

Fernandez, R.; Hunicke, U. D.; Mundt, K. H.; Acosta, P.; Kowalski, W.; Schulz, G.; Gonzalez-Doncel, G.

2001-07-01

The purpose of this investigation is to study the elastic behavior of a discontinuously reinforced composite material, Al(6061)-40vol%SiC, by using three different procedures; Extensometry in uniaxial testing, pendulum elastomeric, and propagation of acoustic signals in the materials. The high ceramic content of this material provides it with a high stiffness without a significant increase in density. Because of this, the material is suitable as structural component in the automotive and aerospace industry. (Author) 8 refs.

Infrared processed Cu composites reinforced with WC particles

International Nuclear Information System (INIS)

Deshpande, P.K.; Li, J.H.; Lin, R.Y.

2006-01-01

Copper matrix composites with WC particle reinforcements have been prepared with an innovative infrared infiltration technique. The volume content of the reinforcement particles in the composite is about 53%. The relative composite density of as high as 99.9% has been obtained with this process. The electric conductivity of composites prepared in this study as determined by a four-point probe method, is similar to commercially available Cu/W composites containing 52 vol% tungsten. Microhardness, microstructure and wear resistance of the composites were also determined. The microstructure of Cu/WC composite reveals excellent wetting between the two constituent phases, WC and copper. The microhardness values of all completely infiltrated Cu/WC composites were in the range of 360-370 HV which is significantly higher than the microhardness of pure copper, 65 HV. Wear resistance of the composites was determined with a pin on disk wear test technique. The wear test results show that composites prepared in this study performed much better than those commercially available Cu/W composites by more than two-fold against silicon carbide abrasive disks

Microstructural analysis and mechanical characterization of aluminum matrix nanocomposites reinforced with uncoated and Cu-coated alumina particles

Energy Technology Data Exchange (ETDEWEB)

Beygi, H., E-mail: hossein.beygi@stu-mail.um.ac.ir; Sajjadi, S.A.; Zebarjad, S.M.

2014-06-01

Aluminum matrix composites used in the aerospace, military and automotive industries are typically fabricated by a stir casting method. However, when nanoparticles are used for reinforcement, fabrication of composite materials by this method leads to the formation of a large number of structural defects. In this study, copper coating of alumina reinforcement particles is investigated as a technique for improving the structure of Al-Al{sub 2}O{sub 3} composites. Microstructural investigations by optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy dispersion spectroscopy (EDS) and transmission electron microscopy (TEM) showed that the alumina particles were coated uniformly with copper shells. Copper coating of the reinforcing particles significantly increased their wettability in the molten aluminum alloy, strengthened the matrix-particle interfaces and improved the distribution of reinforcing particles within the matrix. Due to these microstructural improvements, the hardness, compressive strength, yield stress, tensile strength and elongation of the composites were enhanced by copper coating of the alumina particles.

Microstructural analysis and mechanical characterization of aluminum matrix nanocomposites reinforced with uncoated and Cu-coated alumina particles

International Nuclear Information System (INIS)

Beygi, H.; Sajjadi, S.A.; Zebarjad, S.M.

2014-01-01

Aluminum matrix composites used in the aerospace, military and automotive industries are typically fabricated by a stir casting method. However, when nanoparticles are used for reinforcement, fabrication of composite materials by this method leads to the formation of a large number of structural defects. In this study, copper coating of alumina reinforcement particles is investigated as a technique for improving the structure of Al-Al 2 O 3 composites. Microstructural investigations by optical microscopy (OM), scanning electron microscopy (SEM) equipped with energy dispersion spectroscopy (EDS) and transmission electron microscopy (TEM) showed that the alumina particles were coated uniformly with copper shells. Copper coating of the reinforcing particles significantly increased their wettability in the molten aluminum alloy, strengthened the matrix-particle interfaces and improved the distribution of reinforcing particles within the matrix. Due to these microstructural improvements, the hardness, compressive strength, yield stress, tensile strength and elongation of the composites were enhanced by copper coating of the alumina particles

Mechanical and Tribological Characteristics of TIG Hardfaced Dispersive Layer by Reinforced with Particles Extruded Aluminium

Directory of Open Access Journals (Sweden)

R. Dimitrova

2017-05-01

Full Text Available The article presents the results of the implemented technology for generation of hardfaced dispersive layers obtained by additive material containing reinforcing phase of non-metal particles. The wear resistant coatings are deposited on pure aluminium metal matrix by shielded gas metal-arc welding applying tungsten inert gas (TIG with extruded aluminium wire reinforced by particles as additive material. Wire filler is produced by extrusion of a pack containing metalized and plated by flux micro/nano SiC particles. The metalized particles implanting in the metal matrix and its dispersive hardfacing are realized by solid-state welding under conditions of hot plastic deformation. Tribological characteristics are studied of the hardfaced layers of dispersive reinforced material on pure aluminium metal matrix with and without flux. Hardness profiles of the hardfaced layers are determined by nanoindentation. The surface layers are studied by means of Scanning Electron Microscopy (SEM and Energy Dispersive X-ray (EDX analysis. Increase by 15-31 % of the wear resistance of the hardfaced layers and 30-40 % of their hardness was found, which is due to the implanted in the layer reinforcing phase of metalized micro/nano SiC particles.

Effect of Cryorolling and Aging on Fatigue Behavior of Ultrafine-grained Al6061

Science.gov (United States)

Yadollahpour, M.; Hosseini-Toudeshky, H.; Karimzadeh, F.

2016-05-01

The effects of cryorolling (rolling at liquid nitrogen temperature) and heat treatment on tensile and high-cycle fatigue properties and fatigue crack growth rate of Al6061 alloy have been investigated in the present work. First, the solid solution-treated bulk Al6061 alloy was subjected to cryorolling with 90% total thickness reduction and subsequent short annealing at 205°C for 5 min and peak aging at 148°C for 39 h to achieve grain refinement and simultaneous improvement of the strength and ductility. Then, hardness measurements, tensile tests, fatigue life, and fatigue crack growth rate tests including fractography analyses using scanning electron microscopy were performed on bulk Al6061 alloy, cryorolled (CR), and cryorolled material followed by peak aging (PA). The PA specimen showed improved yield strength by 24%, ultimate tensile strength by 20%, and ductility by 12% as compared with the bulk Al6061 alloy. It is shown that the fatigue strength of both CR and PA specimens under a high-cycle fatigue regime are larger than that of the bulk Al6061 alloy. Also, fatigue crack growth rates of the CR and PA specimens show significant enhancement in fatigue crack growth resistances as compared with the bulk Al6061 alloy, as a result of grain refinement.

Investigation on Mechanical and Fatigue behaviour of Aluminium Based SiC/ZrO2 Particle Reinforced MMC

Science.gov (United States)

Ramesh, S.; Govindaraju, N.; Suryanarayan, C. P.

2018-04-01

The study is the work on Aluminium Metal Matrix Composites (MMC’s), which have wider applications in automobile, aerospace and defense industries, hi-tech engineering and power transmission due to their lightweight, high strength and other unique properties. The Aluminium Matrix Composites (AMC’s) refer to a kind of light weight high performance Aluminium centric material system. AMC’s consist of a non-metallic reinforcement which when included into aluminium matrix offers an advantage over the base material. Reinforcements like SiC, B4C, Al2O3, TiC, TiB2, TiO2 are normally preferred to improve mechanical properties of such composites. Here Aluminium 6061 is preferred as matrix material, while silicon carbide (SiC) and Zirconium di-oxide (ZrO2) is selected as reinforcement compounds. Conventional Stir casting procedure is employed to fabricate the necessary composites compositions, which are I. Al:SiC::100:5 and II. Al:ZrO2:SiC::100:3:2. Experimental results depict that the composition II provides higher hardness of 53.6 RHN as opposed to 45.8 RHN of composition I. In tensile strength composition II demonstrates 96.43 N/mm2 as opposed to 67.229 N/mm2 tensile strength of composition II. The fatigue test indicate a expected number of life cycles to failure of 105 cycles for composition II and over 104 cycles for composition I, at stress ranges of 79.062 MPa and 150.651 MPa respectively.

The effect of reinforcement volume ratio on porosity and thermal conductivity in Al-Mgo composites

Directory of Open Access Journals (Sweden)

Recep Calin

2012-12-01

Full Text Available In this study, the effects of reinforcement volume ratios (RVR on composite structure and thermal conductivity were examined in Al-MgO reinforced metal matrix composites (MMCs of 5%, 10% and 15% RVR produced by melt stirring. In the production of composites, EN AW 1050A aluminum alloy was used as the matrix material and MgO powders with particle size of -105 µm were used as the reinforcement material. For every composite specimen was produced at 500 rev/min stirring speed, at 750 °C liquid matrix temperature and 4 minutes stirring time. Composite samples were cooled under normal atmosphere. Then, microstructures of the samples were determined and evaluated by using Scanning Electron Microscope (SEM and Energy Dispersive X-ray Spectroscopy (EDS analysis. In general, it was observed that the reinforcement exhibited a homogeneous distribution. Furthermore, it was determined that the increase in the RVR increased porosity. From the Scanning Electron Microscope images, a thermal Ansys model was generated to determine effective thermal conductivity. Effective thermal conductivity of Al-MgO composites increased with the decrease in reinforcement volume ratio.

AWS certified solutions architect official study guide associate exam

CERN Document Server

Baron, Joe; Bixler, Tim; Gaut, Biff; Kelly, Kevin E; Senior, Sean; Stamper, John

2017-01-01

This is your opportunity to take the next step in your career by expanding and validating your skills on the AWS cloud. AWS has been the frontrunner in cloud computing products and services, and the AWS Certified Solutions Architect Official Study Guide for the Associate exam will get you fully prepared through expert content, and real-world knowledge, key exam essentials, chapter review questions, access to Sybex's interactive online learning environment, and much more. This official study guide, written by AWS experts, covers exam concepts, and provides key review on exam topics, including: * Mapping Multi-Tier Architectures to AWS Services, such as web/app servers, firewalls, caches and load balancers * Understanding managed RDBMS through AWS RDS (MySQL, Oracle, SQL Server, Postgres, Aurora) * Understanding Loose Coupling and Stateless Systems * Comparing Different Consistency Models in AWS Services * Understanding how AWS CloudFront can make your application more cost efficient, faster and secure * Implem...

The effect of reinforcement percentages on properties of copper matrix composites reinforced with TiC particles

Energy Technology Data Exchange (ETDEWEB)

Bagheri, GH.A., E-mail: Gh.a.bagheri65@gmail.com

2016-08-15

In this research, copper matrix composites reinforced with different amounts of titanium carbide particles were produced by mechanical milling and in-situ formation of reinforcements. Morphology and size of milled powders were inspected by scanning electron microscopy (SEM) several times during milling process. Changes in lattice parameter, crystallite size, lattice strain, dislocation density and Gibbs free energy changes (due to increasing in dislocation densities and grain boundaries) in different samples (with different TiC particles contents) were studied by X-Ray Diffraction technique with Cu-kα radiation and using Nelson–Riley method and Williamson–Hall equation. Microstructure of samples after sintering was investigated by FESEM. Finally, densitometry, hardness, determination of electrical resistance and pin on disk wear test were performed and effect of reinforcement percentages on the physical and mechanical properties of composites was studied. Results show incredible improvement in mechanical properties with increasing in TiC value, even though, electrical conductivity dropped off considerably. - Highlights: • Microstructures, mechanical and physical properties of composites have been studied. • Stored Gibbs free energy of dislocations and grain boundaries has been calculated. • Gibbs free energy increased with increasing in titanium percent. • Higher TiC percentage led to better mechanical and unfavorable physical properties.

Microstructure, cold workability and strain hardening behavior of trimodaled AA 6061-TiO2 nanocomposite prepared by mechanical alloying

International Nuclear Information System (INIS)

Sivasankaran, S.; Sivaprasad, K.; Narayanasamy, R.

2011-01-01

Highlights: → Trimodaled composites consisting of UFG and CG matrix phases and ceramic phase were produced successfully. → Cold deformation behavior was investigated. → The 15% CG trimodaled composite yielded a high compressive strength of 935 MPa. → The 30% CG composite exhibited higher ductility while maintaining strength and toughness. - Abstract: In the present work, the improvement of compressive ductility while maintaining high strength and toughness for nanocrystalline materials by cold upsetting (incremental loads) of bulk trimodaled composite was studied. Mechanically alloyed nanocrystalline (NC) AA 6061 alloy powders reinforced with nano TiO 2 were blended with 0, 5, 10, 15, 20, 25, and 30 wt.% coarse grain (CG) elemental powders related to AA 6061 alloy composition to produce trimodal microstructure. The synthesized composite preforms were characterized by optical microscope, scanning electron microscope, transmission electron microscope and X-ray diffraction. The room temperature compressive deformation behavior was evaluated under triaxial stress state condition. With increasing percentage of CG phase in the nanocomposite, the gradual improvement in compressive ductility was observed at the cost of a small amount of strength but it favored the ease of deformation. The 15% CG trimodal composite exhibited an extremely high compressive strength of 935 MPa due to non-coalescence of individual CG particles and effective load transfer occurred in multi scale microstructures. But the 30% CG trimodal composite showed an incremental compressive ductility of around 16% while sacrificing a small amount of strength (845 MPa) and this composite displayed improved toughness (area under true effective stress and true effective strain curve) of over 600% than nanocomposite (0% CG). Also, the percentage cold workability of 30% CG composite was six times higher than that of 0% CG composite. Hence, the 30% CG trimodal composite was observed to be the good one as

Corrosion Properties of Dissimilar Friction Stir Welded 6061 Aluminum and HT590 Steel

Science.gov (United States)

Seo, Bosung; Song, Kuk Hyun; Park, Kwangsuk

2018-05-01

Corrosion properties of dissimilar friction stir welded 6061 aluminum and HT590 steel were investigated to understand effects of galvanic corrosion. As cathode when coupled, HT590 was cathodically protected. However, the passivation of AA6061 made the aluminum alloy cathode temporarily, which leaded to corrosion of HT590. From the EIS analysis showing Warburg diffusion plot in Nyquist plots, it can be inferred that the stable passivation layer was formed on AA6061. However, the weld as well as HT590 did not show Warburg diffusion plot in Nyquist plots, suggesting that there was no barrier for corrosion or even if it exists, the barrier had no function for preventing and/or retarding charge transport through the passivation layer. The open circuit potential measurements showed that the potential of the weld was similar to that of HT590, which lied in the pitting region for AA6061, making the aluminum alloy part of the weld keep corrosion state. That resulted in the cracked oxide film on AA6061 of the weld, which could not play a role of corrosion barrier.

Development of novel Mg–Ni60Nb40 amorphous particle reinforced composites with enhanced hardness and compressive response

International Nuclear Information System (INIS)

Jayalakshmi, S.; Sahu, Shreyasi; Sankaranarayanan, S.; Gupta, Sujasha; Gupta, M.

2014-01-01

Development of amorphous alloy/glassy particle reinforced light metal composites is an emerging research field. In this investigation, we have synthesized and characterized Ni 60 Nb 40 amorphous alloy particle reinforced Mg-composites with varying volume fractions. Microwave-assisted two-directional rapid sintering technique followed by hot extrusion was used to produce these pure Mg-based composites. The structural and mechanical properties of the developed composites were investigated, and are discussed using structure–property relationship. Structural analysis indicated the retention of amorphous structure of the reinforcement in all the composites. It was found that the distribution of the reinforcement was strongly dependent on the volume fraction (V f ). The addition of Ni 60 Nb 40 amorphous alloy particles modified the preferred crystal orientation of Mg, as was observed from X-ray diffraction (XRD) analysis. The composites showed significant improvement in hardness (increment up to 120%) and compressive strength (∼85% increase at 5% V f ). Comparison of mechanical properties of the developed composites with those of conventional Mg-composites having ceramic/metallic reinforcements, highlight the effectiveness of using amorphous particles as promising reinforcement materials. - Highlights: • Novel Mg-composites reinforced with Ni 60 Nb 40 amorphous particles were developed . • Microwave sintering and hot extrusion were used to synthesize the composites. • Reinforcements retained the amorphous structure, and changed Mg-crystal orientation. • Composites showed significant enhancement in hardness and compressive properties. • Performance of developed composites are superior/competitive to conventional MMCs

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

Energy Technology Data Exchange (ETDEWEB)

Selvakumar, S., E-mail: lathaselvam1963@gmail.com [Department of Mechanical Engineering, Nehru Institute of Technology, Coimbatore 641105, Tamil Nadu (India); Department of Mechanical Engineering, Anna University, Chennai 600025, Tamil Nadu (India); Dinaharan, I., E-mail: dinaweld2009@gmail.com [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa); Palanivel, R., E-mail: rpalanivelme@gmail.com [Department of Mechanical Engineering Science, University of Johannesburg, Auckland Park Kingsway Campus, Johannesburg 2006 (South Africa); Ganesh Babu, B., E-mail: profbgb@gmail.com [Department of Mechanical Engineering, Roever College of Engineering and Technology, Perambalur 621212, Tamil Nadu (India)

2017-03-15

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

Characterization of molybdenum particles reinforced Al6082 aluminum matrix composites with improved ductility produced using friction stir processing

International Nuclear Information System (INIS)

Selvakumar, S.; Dinaharan, I.; Palanivel, R.; Ganesh Babu, B.

2017-01-01

Aluminum matrix composites (AMCs) reinforced with various ceramic particles suffer a loss in ductility. Hard metallic particles can be used as reinforcement to improve ductility. The present investigation focuses on using molybdenum (Mo) as potential reinforcement for Mo(0,6,12 and 18 vol.%)/6082Al AMCs produced using friction stir processing (FSP). Mo particles were successfully retained in the aluminum matrix in its elemental form without any interfacial reaction. A homogenous distribution of Mo particles in the composite was achieved. The distribution was independent upon the region within the stir zone. The grains in the composites were refined considerably due to dynamic recrystallization and pinning effect. The tensile test results showed that Mo particles improved the strength of the composite without compromising on ductility. The fracture surfaces of the composites were characterized with deeply developed dimples confirming appreciable ductility. - Highlights: •Molybdenum particles used as reinforcement for aluminum composites to improve ductility. •Molybdenum particles were retained in elemental form without interfacial reaction. •Homogeneous dispersion of molybdenum particles were observed in the composite. •Molybdenum particles improved tensile strength without major loss in ductility. •Deeply developed dimples on the fracture surfaces confirmed improved ductility.

Elastohydrodynamic lubrication in point contact on the surfaces of particle-reinforced composite

Science.gov (United States)

Chen, Keying; Zeng, Liangcai; Wu, Zhenpeng; Zheng, Feilong

2018-04-01

Appreciable friction and serious wear are common challenges in the operation of advanced manufacturing equipment, and friction pairs may be susceptible to damage even with oil lubrication when point contact exists. In this study, a type of particle-reinforced composite material is introduced for one of the components of a heavy-load contact pair, and the performance improvement of elastohydrodynamic lubrication (EHL) is analyzed considering the rheological properties of non-Newtonian fluids. The Ree-Eyring EHL model is used considering the surface of the particle-reinforced composite, in which the film thickness includes the particle-induced elastic deformation. The problem of inclusions with different eigenstrains is solved by using Galerkin vectors. The influences of particle properties, size, burial depth, and interparticle distance on point-contact EHL are investigated. Furthermore, using several cases, the structural parameters of the particles in the composites are optimized, and an appropriate parameter range is obtained with the goal of reducing friction. Finally, the results for the EHL traction coefficient demonstrate that appropriate particle properties, size, burial depth, and interparticle distance can effectively reduce the traction coefficient in heavy-load contact.

Study of the corrosion of AA 6061 in spent fuel materials

International Nuclear Information System (INIS)

Rodriguez, Sebastian; Haddad, Roberto; Lanzani, Liliana A.

2003-01-01

Localized attack induced by dust or other particles deposited on alloy AA 6061 surface under water has been addressed as a matter of concern after completion of an IAEA Coordinated Research Program (CRP) on the corrosion of aluminum clad spent fuel during storage in water basins. This attack has been observed in all kinds of waters, although it is more pronounced in those of higher conductivity. In these cases a strong attack (similar to pitting corrosion) up to several hundred microns in depth and about a millimeter in length has been found beneath the aluminum hydroxide blister formed in those places where specks had seated on. As this problem could seriously affect the fission product containing capacity of stored spent fuel even in well maintained high quality water, it is important to learn about the involved mechanism of attack and find out about the influence of particle composition, in order to establish the convenience or disapproval of the use of materials and procedures in storage basins. With this objective, an experimental approach has been developed to study the mechanism of corrosion attack linked with the deposition of particles of different composition on aluminum surfaces; this include two kinds of iron flakes, concrete powder, and sand particles. Immersion tests of up to 40 days have been conducted in nuclear grade demineralized water and sodium citrate solutions of several conductivities. The position of sediments was marked and followed through the process and the final state of the aluminum surfaces was assessed by optical and electron microscopy and other microanalysis techniques. Other complementary activities carried on in relation with this work are: through characterization of intermetallic particles in AA 6061, and the study of the electrochemical behavior of precipitates in high purity water. Mg 2 Si particles perform very actively, dissolving even in high pure water at open circuit potential, leaving a small hole on the surface. Iron

Python and AWS Cookbook

CERN Document Server

Garnaat, Mitch

2011-01-01

If you intend to use Amazon Web Services (AWS) for remote computing and storage, Python is an ideal programming language for developing applications and controlling your cloud-based infrastructure. This cookbook gets you started with more than two dozen recipes for using Python with AWS, based on the author's boto library. You'll find detailed recipes for working with the S3 storage service as well as EC2, the service that lets you design and build cloud applications. Each recipe includes a code solution you can use immediately, along with a discussion of why and how the recipe works. You al

Effect of technological parameters on formability of semi-solid rheological casting-forging 6061 alloy

Directory of Open Access Journals (Sweden)

Jianbo TAN

2016-02-01

Full Text Available The 6061 alloy cooling curve is determined by analysis software, and the 6061 semi-solid alloy is prepared by manual paddling process. The primary solid fraction is tested through prepared water quenched samples under different temperature. With H1F100 type servo press and cup type test mold, the forming of the 6061 semi-solid alloy rheological casting-forging is made. The influence of alloy temperature, forming pressure, upper mould temperature and holding time on the formability of 6061 alloy is researched. The results show that within the same set of mold completing casting and forging of the alloy is feasible. Along with the increase of the alloy temperature and the upper mould temperature, the formability of finished products becomes better. Under this experimentation, when the temperature of the semi-solid alloy is amongst 642 ℃ to 645 ℃ and the upper mould preheating temperature is amongst 200 ℃ to 300 ℃, casting defects such as cold insulation will form in the casting-forging sample of semi-solid 6061 alloy with the prolongation of holding time.

Effect of Particle Size on Microstructure and Mechanical Properties of Al-Based Composite Reinforced with 10 Vol.% Mechanically Alloyed Mg-7.4%Al Particles

Directory of Open Access Journals (Sweden)

Anil K. Chaubey

2016-11-01

Full Text Available The effect of Mg-7.4%Al reinforcement particle size on the microstructure and mechanical properties in pure Al matrix composites was investigated. The samples were prepared by hot consolidation using 10 vol.% reinforcement in different size ranges, D, 0 < D < 20 µm (0–20 µm, 20 ≤ D < 40 µm (20–40 µm, 40 ≤ D < 80 µm (40–80 µm and 80 ≤ D < 100 µm (80–100 µm. The result reveals that particle size has a strong influence on the yield strength, ultimate tensile strength and percentage elongation. As the particle size decreases from 80 ≤ D < 100 µm to 0 < D < 20 µm, both tensile strength and ductility increases from 195 MPa to 295 MPa and 3% to 4% respectively, due to the reduced ligament size and particle fracturing. Wear test results also corroborate the size effect, where accelerated wear is observed in the composite samples reinforced with coarse particles.

Mechanical and tribological characterization of the Al 6061-T651 and the Al 6061-T651 with chromium phosphate coating

International Nuclear Information System (INIS)

Pena B, A.

2002-01-01

This work consist of two parts. The first one, related with theoretic concepts of tribology, condensed the friction and wear phenomena, considering aspects to bring something relevant into a process. In this conditions, to add lubricant cause a significant performance change during the phenomena mentioned above. The second part of this work, described experimental aspects as how we do a chromium phosphate coating in immersion cell, using 6061-T651 aluminum as substrate. In the process, we consider values of parameters in optimum conditions, obtained by commercial aluminum during previous investigations made in National Institute of Nuclear Research. Here, we characterized chromium phosphate coating and, 6061-T651 aluminum alloy using Sem and X-Ray Diffraction techniques. The measurement of some chromium phosphate characteristic as thickness, weight for area unit, density, roughness, microhardness, adhesion and corrosion resistant were made with appropriately equipment and, in accordance with international standards procedures. In tribological aspect, we determinate adhesive wear resistance and abrasive wear resistance for 6061-T651 aluminum alloy and chromium phosphate coating. Adhesive wear resistance was made for dry condition while abrasive wear resistance were made for dry and wet conditions. Tests are to guide by ASTM G99, G65 and G105 designations respectively. (Author)

TiB2/Al2O3 ceramic particle reinforced aluminum fabricated by spray deposition

International Nuclear Information System (INIS)

Chen Xing; Yang Chengxiao; Guan Leding; Yan Biao

2008-01-01

Aluminum matrix ceramic particle reinforced composites (AMCs) is a kind of composite with great importance. Aluminum matrix composite reinforced with TiB 2 /Al 2 O 3 ceramic particles was successfully in situ synthesized in Al-TiO 2 -B 2 O 3 system in this paper, using spray deposition with hot-press treatment technique. Five groups of composites with different reinforcement volume contents were prepared and the comparisons of porosity, ultimate tensile strength (UTS), elongation and Brinell hardness (BH) between the composites with and without hot-press treating were carried out. The composite with 21.0% reinforcement volume content was analyzed by X-ray diffraction (XRD), Environmental Scanning Electron Microscope (ESEM), Transmission Electron Microscope (TEM) and Energy Disperse Spectroscopy (EDS). The results revealed the formation and uniform distribution of fine reinforcements in the matrix after hot-press treating, while a new intermetallic phase Al 3 Ti was found besides TiB 2 /Al 2 O 3 ceramic phase

Comparison of mechanical and tribotechnical properties of UHMWPE reinforced with basalt fibers and particles

Science.gov (United States)

Panin, S. V.; Kornienko, L. A.; Alexenko, V. O.; Qitao, Huang; Ivanova, L. R.

2016-11-01

Mechanical and tribotechnical properties of UHMWPE composites reinforced with basalt fibers and particles under dry sliding friction and abrasion were investigated. It is shown that adding of the basalt particles provides higher wear resistance under the dry sliding friction while at abrasion filling by the basalt fibers is more efficient since the wear resistance of the reinforced UHMWPE composites is by 3.7 times higher in contrast with the neat polymer. Wear mechanisms of the polymeric UHMWPE composites under various types of wear are discussed.

Laser surface forming of AlCoCrCuFeNi particle reinforced AZ91D matrix composites

Science.gov (United States)

Meng, Guanghui; Yue, T. M.; Lin, Xin; Yang, Haiou; Xie, Hui; Ding, Xu

2015-07-01

Traditionally, the laser melt injection (LMI) technique can only be used for forming ceramic particles reinforced metal matrix composites (MMCs) for enhancing surface properties of lightweight engineering materials. In this research, the LMI method was employed to form metal particles reinforced MMCs on AZ91D instead. This was viable because of the unique properties of the AlCoCrCuFeNi high-entropy alloy (HEA) metal particles used. The large difference in melting point between the HEA and the substrate material (AZ91D), and the limited reaction and the lack of fusion between the HEA and Mg have made it possible that a metal particles reinforced AZ91D composite material was produced. The reason of limited reaction was considered mainly due to the relatively high mixing enthalpy between the HEA constituent elements and Mg. Although there was some melting occurred at the particles surface with some solute segregation found in the vicinity close to the surface, intermetallic compounds were not observed. With regard to the wear resistance of the MMCs, it was found that when the volume fraction of the reinforcement phase, i.e. the HEA particles, reached about 0.4, the wear volume loss of the coating was only one-seventh of that of the substrate material.

Flexible high-loading particle-reinforced polyurethane magnetic nanocomposite fabrication through particle-surface-initiated polymerization

International Nuclear Information System (INIS)

Guo Zhanhu; Park, Sung; Wei Suying; Pereira, Tony; Moldovan, Monica; Karki, Amar B; Young, David P; Hahn, H Thomas

2007-01-01

Flexible high-loading nanoparticle-reinforced polyurethane magnetic nanocomposites fabricated by the surface-initiated polymerization (SIP) method are reported. Extensive field emission scanning electron microscopic (SEM) and atomic force microscopic (AFM) observations revealed a uniform particle distribution within the polymer matrix. X-ray photoelectron spectrometry (XPS) and differential thermal analysis (DTA) revealed a strong chemical bonding between the nanoparticles and the polymer matrix. The elongation of the SIP nanocomposite under tensile test was about four times greater than that of the composite fabricated by a conventional direct mixing fabrication method. The nanocomposite shows particle-loading-dependent magnetic properties, with an increase of coercive force after the magnetic nanoparticles were embedded into the polymer matrix, arising from the increased interparticle distance and the introduced polymer-particle interactions

Influence of thermal residual stress on behaviour of metal matrix composites reinforced with particles

Science.gov (United States)

Guzmán, R. E.; Hernández Arroyo, E.

2016-02-01

The properties of a metallic matrix composites materials (MMC's) reinforced with particles can be affected by different events occurring within the material in a manufacturing process. The existence of residual stresses resulting from the manufacturing process of these materials (MMC's) can markedly differentiate the curves obtained in tensile tests obtained from compression tests. One of the themes developed in this work is the influence of residual stresses on the mechanical behaviour of these materials. The objective of this research work presented is numerically estimate the thermal residual stresses using a unit cell model for the Mg ZC71 alloy reinforced with SiC particles with volume fraction of 12% (hot-forging technology). The MMC's microstructure is represented as a three dimensional prismatic cube-shaped with a cylindrical reinforcing particle located in the centre of the prism. These cell models are widely used in predicting stress/strain behaviour of MMC's materials, in this analysis the uniaxial stress/strain response of the composite can be obtained through the calculation using the commercial finite-element code.

Oxidation behavior of TiC particle-reinforced 304 stainless steel

International Nuclear Information System (INIS)

Wu Qianlin; Zhang Jianqiang; Sun Yangshan

2010-01-01

TiC particle-reinforced 304 stainless steels were prepared using a new developed in situ technology and exhibited the uniform distribution of TiC particles in the matrix. The oxidation behavior of 304SS-2TiC and 304SS-6TiC (all in weight percentage) was compared with that of 304SS at 850 deg. C in air for 96 h using thermogravimetry analysis. For 304SS, the rate of weight gain was very slow initially, but accelerated suddenly to a very high level, forming breakaway oxidation. The addition of TiC particles to 304SS resulted in no breakaway oxidation and maintained a low oxidation rate in the whole reaction time investigated. Examination of oxide scale morphology and cross-section analysis by scanning electron microscopy and optical microscopy showed a significant scale spallation and a deep oxide penetration in the case of 304SS, but a rather continuous, dense and adherent oxide layer formed on the surface of TiC particle-reinforced alloys. XRD analysis revealed the presence of Cr 2 O 3 together with spinel-type oxides in the oxide scale. For TiC-containing alloys, fine TiO 2 was also found on the surface and the amount of this oxide increased with TiC addition. The TiC addition developed finer matrix structure before oxidation, which accelerates chromium diffusion. As a result, scale adherence was improved and oxidation resistance was increased.

Constitutional equations of thermal stresses of particle-reinforced composite

International Nuclear Information System (INIS)

Asakawa, Atsushi; Noda, Naotake; Tohgo, Keiichiro; Tsuji, Tomoaki.

1994-01-01

Functionally gradient materials (FGM) have been developed as ultrahigh-heat-resistant materials in aircraft, space engineering and nuclear fields. In the heat-resistant FGM which contain particles (ceramics) in the matrix (metal), the matrix will be subjected to plastic deformation, particles will be debonded, and finally cracks will be generated. The constitutive equations of FGM which take into account the damage process and change in temperature are necessary in order to solve these phenomena. In this paper, the constitutive equations of particle-reinforced composites with consideration of the damage process and change in temperature are estimated by the equivalent inclusion method in terms of elastoplasticity. The stress-strain relations and the coefficients of linear thermal expansion of the composites (Al-PSZ and Ti-PSZ) are calculated in ultrahigh temperature. (author)

Advances in Thermal Spray Deposition of Billets for Particle Reinforced Light Metals

International Nuclear Information System (INIS)

Wenzelburger, Martin; Zimmermann, Christian; Gadow, Rainer

2007-01-01

Forming of light-metals in semi-solid state offers some advantages like low process temperatures, improved mould durability, good flow behavior and fine, globular microstructure of the final material. By the introduction of ceramic particles, increased elastic modulus and yield strength as well as wear resistance and creep behavior can be obtained. By semi-solid forging or semi-solid casting, particle reinforced metals (PRM) can be produced with improved matrix microstructure and beneficial forming process parameters compared to conventional MMC manufacturing techniques. The production of this kind of light metal matrix composites requires the supply of dense semi-finished parts with well defined volume fractions of homogeneously distributed particulate reinforcement. A manufacturing method for cylindrical light metal billets is described that applies thermal spraying as a build-up process for simultaneous deposition of matrix and reinforcement phase with cored wires as spraying material. Thermal spraying leads to small grain sizes and prevents dendrite formation. However, long process cycle times lead to billet heating and recrystallization of the matrix microstructure. In order to preserve small grain sizes that enable semi-solid forming, the thermal spraying process was analyzed by in-flight particle analysis and thermography. As a consequence, the deposition process was optimized by adaptation of the thermal spraying parameters and by application of additional cooling, leading to lower billet temperatures and finer PRM billet microstructure

The erosion performance of particle reinforced metal matrix composite coatings produced by co-deposition cold gas dynamic spraying

Science.gov (United States)

Peat, Tom; Galloway, Alexander; Toumpis, Athanasios; McNutt, Philip; Iqbal, Naveed

2017-02-01

This work reports on the erosion performance of three particle reinforced metal matrix composite coatings, co-deposited with an aluminium binder via cold-gas dynamic spraying. The deposition of ceramic particles is difficult to achieve with typical cold spray techniques due to the absence of particle deformation. This issue has been overcome in the present study by simultaneously spraying the reinforcing particles with a ductile metallic binder which has led to an increased level of ceramic/cermet particles deposited on the substrate with thick (>400 μm) coatings produced. The aim of this investigation was to evaluate the erosion performance of the co-deposited coatings within a slurry environment. The study also incorporated standard metallographic characterisation techniques to evaluate the distribution of reinforcing particles within the aluminium matrix. All coatings exhibited poorer erosion performance than the uncoated material, both in terms of volume loss and mass loss. The Al2O3 reinforced coating sustained the greatest amount of damage following exposure to the slurry and recorded the greatest volume loss (approx. 2.8 mm3) out of all of the examined coatings. Despite the poor erosion performance, the WC-CoCr reinforced coating demonstrated a considerable hardness increase over the as-received AA5083 (approx. 400%) and also exhibited the smallest free space length between adjacent particles. The findings of this study reveal that the removal of the AA5083 matrix by the impinging silicon carbide particles acts as the primary wear mechanism leading to the degradation of the coating. Analysis of the wear scar has demonstrated that the damage to the soft matrix alloy takes the form of ploughing and scoring which subsequently exposes carbide/oxide particles to the impinging slurry.

Al-matrix composite materials reinforced by Al-Cu-Fe particles

International Nuclear Information System (INIS)

Bonneville, J; Laplanche, G; Joulain, A; Gauthier-Brunet, V; Dubois, S

2010-01-01

Al-matrix material composites were produced using hot isostatic pressing technique, starting with pure Al and icosahedral (i) Al-Cu-Fe powders. Depending on the processing temperature, the final reinforcement particles are either still of the initial i-phase or transformed into the tetragonal ω-Al0 0.70 Cu 0.20 Fe 0.10 crystalline phase. Compression tests performed in the temperature range 293K - 823K on the two types of composite, i.e. Al/i and Al/ω, indicate that the flow stress of both composites is strongly temperature dependent and exhibit distinct regimes with increasing temperature. Differences exist between the two composites, in particular in yield stress values. In the low temperature regime (T ≤ 570K), the yield stress of the Al/ω composite is nearly 75% higher than that of the Al/i composite, while for T > 570K both composites exhibit similar yield stress values. The results are interpreted in terms of load transfer contribution between the matrix and the reinforcement particles and elementary dislocation mechanisms in the Al matrix.

Advantages and disadvantages of composite pistons for small power combustion engines

Directory of Open Access Journals (Sweden)

Andrzej POSMYK

2007-01-01

Full Text Available The results of technological and metallographic investigations of small dimensions, low power combustion engines piston has been presented. Semi-finished pistons has been produced by gravitations casting of composite material with EN-AC-47000 alloy matrix +15% Al2O3P and EN-AW-6061 alloy matrix +22% Al2O3P. Some small casting defects have been detected during the cutting process of piston made of composite material with EN-AC-47000 alloy matrix +15% Al2O3P. These defects were sources of micro perforations. In the piston made of EN-AW-6061 alloy matrix has been any defects detected.

Compressive strength, plastic flow properties, and surface frictional effects of 1100, 3003 and 6061 aluminum alloys

Energy Technology Data Exchange (ETDEWEB)

Pinkerton, Gary Wayne [Univ. of Illinois, Urbana-Champaign, IL (United States)

1993-01-01

The purpose of this study is to find aluminum alloys that are effective for use as wire vacuum seals in the 800MeV particle accelerator located at the Louis Anderson Meson Physics Facility (LAMPF) in Los Alamos, NM. Three alloys, Al 1100, Al 3003, and Al 6061, are investigated under uniaxial compression to determine stresses for a given height reduction from 0 to 70 percent, and to find plastic flow and surface interaction effects. Right-circular cylindrical specimens are compressed on-end (cylindrically) and radially (for modeling as compressed wire). Aluminum 1100 and 3003 alloys are compared for length to diameter ratios of 1 and 2 for both compression types, and are then compared to results of radial compression of annealed small diameter Al 1100 wire currently used at LAMPE. The specimens are also compressed between three different platen surfaces, polished steel, etched steel, and aluminum 6061-T6, to determine effects of friction. The Al 3003 alloy exhibits 20 to 25% lower stresses at all height reductions than Al 1100 for both cylindrical and radial compression.

Compressive strength, plastic flow properties, and surface frictional effects of 1100, 3003 and 6061 aluminum alloys

International Nuclear Information System (INIS)

Pinkerton, G.W.

1993-01-01

The purpose of this study is to find aluminum alloys that are effective for use as wire vacuum seals in the 800MeV particle accelerator located at the Louis Anderson Meson Physics Facility (LAMPF) in Los Alamos, NM. Three alloys, Al 1100, Al 3003, and Al 6061, are investigated under uniaxial compression to determine stresses for a given height reduction from 0 to 70 percent, and to find plastic flow and surface interaction effects. Right-circular cylindrical specimens are compressed on-end (cylindrically) and radially (for modeling as compressed wire). Aluminum 1100 and 3003 alloys are compared for length to diameter ratios of 1 and 2 for both compression types, and are then compared to results of radial compression of annealed small diameter Al 1100 wire currently used at LAMPE. The specimens are also compressed between three different platen surfaces, polished steel, etched steel, and aluminum 6061-T6, to determine effects of friction. The Al 3003 alloy exhibits 20 to 25% lower stresses at all height reductions than Al 1100 for both cylindrical and radial compression

Particle Board and Oriented Strand Board Prepared with Nanocellulose-Reinforced Adhesive

Directory of Open Access Journals (Sweden)

Stefan Veigel

2012-01-01

Full Text Available Adhesives on the basis of urea-formaldehyde (UF and melamine-urea-formaldehyde (MUF are extensively used in the production of wood-based panels. In the present study, the attempt was made to improve the mechanical board properties by reinforcing these adhesives with cellulose nanofibers (CNFs. The latter were produced from dissolving grade beech pulp by a mechanical homogenization process. Adhesive mixtures with a CNF content of 0, 1, and 3 wt% based on solid resin were prepared by mixing an aqueous CNF suspension with UF and MUF adhesives. Laboratory-scale particle boards and oriented strand boards (OSBs were produced, and the mechanical and fracture mechanical properties were investigated. Particle boards prepared with UF containing 1 wt% CNF showed a reduced thickness swelling and better internal bond and bending strength than boards produced with pure UF. The reinforcing effect of CNF was even more obvious for OSB where a significant improvement of strength properties of 16% was found. For both, particle board and OSB, mode I fracture energy and fracture toughness were the parameters with the greatest improvement indicating that the adhesive bonds were markedly toughened by the CNF addition.

Bio-composites based on polypropylene reinforced with Almond Shells particles: Mechanical and thermal properties

International Nuclear Information System (INIS)

Essabir, H.; Nekhlaoui, S.; Malha, M.; Bensalah, M.O.; Arrakhiz, F.Z.; Qaiss, A.; Bouhfid, R.

2013-01-01

Highlights: • Almond Shells (ASs) particles have been used as reinforcement in polypropylene matrix. • The SEBS-g-MA has been used to improve the adhesion between matrix and particles. • The mechanical and thermal properties of the composite have been improved by the AS. - Abstract: In this work, Almond Shells (ASs) particles are used as reinforcement in a thermoplastic matrix as polypropylene (PP). Composites containing Almond Shells (ASs) particles with and without compatibilizer (maleic anhydride grafted polypropylene; SEBS-g-MA) for various particle content (5, 10, 15, 20, 25, 30 wt.%) was investigated by means of studying their mechanical, thermal and rheological properties. The composites were prepared in a twin-screw extruder and assessed by means of X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), tensile testing and Dynamic Mechanical Analysis (DMA). Results show a clear improvement in mechanical and rheological properties from the use of Almond Shells particles in the matrix without and with maleic anhydride compatibilizer, corresponding to a gain in Young’s modulus of 56.2% and 35% respectively, at 30 wt.% particle loading. Thermal analysis revealed that incorporation of particle in the composites resulted in increase in the initial thermal decomposition temperatures

Acceptance/operational test procedure 101-AW tank camera purge system and 101-AW video camera system

International Nuclear Information System (INIS)

Castleberry, J.L.

1994-01-01

This procedure will document the satisfactory operation of the 101-AW Tank Camera Purge System (CPS) and the 101-AW Video Camera System. The safety interlock which shuts down all the electronics inside the 101-AW vapor space, during loss of purge pressure, will be in place and tested to ensure reliable performance. This procedure is separated into four sections. Section 6.1 is performed in the 306 building prior to delivery to the 200 East Tank Farms and involves leak checking all fittings on the 101-AW Purge Panel for leakage using a Snoop solution and resolving the leakage. Section 7.1 verifies that PR-1, the regulator which maintains a positive pressure within the volume (cameras and pneumatic lines), is properly set. In addition the green light (PRESSURIZED) (located on the Purge Control Panel) is verified to turn on above 10 in. w.g. and after the time delay (TDR) has timed out. Section 7.2 verifies that the purge cycle functions properly, the red light (PURGE ON) comes on, and that the correct flowrate is obtained to meet the requirements of the National Fire Protection Association. Section 7.3 verifies that the pan and tilt, camera, associated controls and components operate correctly. This section also verifies that the safety interlock system operates correctly during loss of purge pressure. During the loss of purge operation the illumination of the amber light (PURGE FAILED) will be verified

Impact Strength of Composite Materials Based on EN AC-44200 Matrix Reinforced with Al2O3 Particles

OpenAIRE

Kurzawa A.; Kaczmar J.W.

2017-01-01

The paper presents the results of research of impact strength of aluminum alloy EN AC-44200 based composite materials reinforced with alumina particles. The research was carried out applying the materials produced by the pressure infiltration method of ceramic preforms made of Al2O3 particles of 3-6μm with the liquid EN AC-44200 Al alloy. The research was aimed at determining the composite resistance to dynamic loads, taking into account the volume of reinforcing particles (from 10 to 40% by ...

Effect of particle shapes on effective strain gradient of SiC particle reinforced aluminum composites

International Nuclear Information System (INIS)

Liu, X; Cao, D F; Mei, H; Liu, L S; Lei, Z T

2013-01-01

The stress increments depend not only on the plastic strain but also on the gradient of plastic strain, when the characteristic length scale associated with non-uniform plastic deformation is on the order of microns. In the present research, the Taylor-based nonlocal theory of plasticity (TNT plasticity), with considering both geometrically necessary dislocations and statistically stored dislocations, is applied to investigated the effect of particle shapes on the strain gradient and mechanical properties of SiC particle reinforced aluminum composites (SiC/Al composites). Based on this theory, a two-dimensional axial symmetry cell model is built in the ABAQUS finite element code through its USER-ELEMENT (UEL) interface. Some comparisons with the classical plastic theory demonstrate that the effective stress predicted by TNT plasticity is obviously higher than that predicted by classical plastic theory. The results also demonstrate that the irregular particles cause higher effective gradient strain which is attributed to the fact that angular shape particles give more geometrically.

Influence of tool pin in friction stir welding on activated carbon reinforced aluminium metal matrix composite

Science.gov (United States)

DijuSamuel, G.; Raja Dhas, J. Edwin

2017-10-01

This paper focus on impact of tool pin in friction stir welding on activated carbon reinforced aluminium metal matrix composite. For fabrication of metal matrix composite AA6061 is used as matrix and activated carbon is used as reinforcement and it is casted using modified stir casting technique. After casting metal matrix composite has undergone various microstructure tests like SEM,EDAX and XRD. FSW is carried out in this metal matrix composite by choosing various tool pin profile like square,round,Threaded round, hexagon and taper. The quality of welded plates is measured in terms of ultimate tensile strength and hardness.

Hardness Optimization for Al6061-MWCNT Nanocomposite Prepared by Mechanical Alloying Using Artificial Neural Networks and Genetic Algorithm

Directory of Open Access Journals (Sweden)

Mehrdad Mahdavi Jafari

2017-06-01

Full Text Available Among artificial intelligence approaches, artificial neural networks (ANNs and genetic algorithm (GA are widely applied for modification of materials property in engineering science in large scale modeling. In this work artificial neural network (ANN and genetic algorithm (GA were applied to find the optimal conditions for achieving the maximum hardness of Al6061 reinforced by multiwall carbon nanotubes (MWCNTs through modeling of nanocomposite characteristics. After examination the different ANN architectures an optimal structure of the model, i.e. 6-18-1, is obtained with 1.52% mean absolute error and R2 = 0.987. The proposed structure was used as fitting function for genetic algorithm. The results of GA simulation predicted that the combination sintering temperature 346 °C, sintering time 0.33 h, compact pressure 284.82 MPa, milling time 19.66 h and vial speed 310.5 rpm give the optimum hardness, (i.e., 87.5 micro Vickers in the composite with 0.53 wt% CNT. Also, sensitivity analysis shows that the sintering time, milling time, compact pressure, vial speed and amount of MWCNT are the significant parameter and sintering time is the most important parameter. Comparison of the predicted values with the experimental data revealed that the GA–ANN model is a powerful method to find the optimal conditions for preparing of Al6061-MWCNT.

Fatigue properties of particle reinforced aluminium alloys

International Nuclear Information System (INIS)

Tabernig, B.J.

2000-06-01

In this work the particle reinforced Al-alloys 359 T6 + 20 % SiC and 2124 + 17 % SiC which differ significantly in their production and microstructure are investigated. Standard and in-situ tensile tests show, that in the powder metallurgically produced alloy 2124 reinforcement leads to a higher Young's modulus, yield and ultimate tensile stress where the cast alloy 359 + 20 % SiC exhibit increased stiffness, but low ductility due to cast porosity of some 100 μm. The failure mechanism governed by microstructural parameters is found to play an important role for ductility. The fatigue properties are investigated with specific regard to the influence of the in-service condition (load ratio, temperature, variable amplitude loading) in the foreseen applications in the automobile- and aerospace industry. Standard fatigue tests point out that the endurance limit is improved by reinforcement, but is strongly dependent on the size of given initial defects. The fatigue crack properties are characterised by standard crack growth curves and r(esistance)-curves for the threshold of stress intensity factor range. Both composites exhibit a higher effective threshold than their unreinforced alloys. Furthermore the fatigue resistance described by the R-curve as well as the long crack threshold are improved in the alloy 2124 + 17 % SiC. While in crack growth tests under constant amplitude loading the alloy 2124 + 17 % SiC shows lower crack growth rates than its unreinforced alloy, the opposite case is in the alloy 359 + 20 % SiC at high DK. Periodic overloads lead in the 359 + 20 % SiC to particle fracture at the crack tip and to a steeper increase in the crack growth rate. In the 2124 + 17% SiC the fatigue crack grows predominately in the matrix and a retardation effect due to overloads is observed. In order to describe the fatigue limit of components as a function of initial defect size an analytical concept is developed assuming that the fatigue limit is controlled by the

INFLUENCE OF MECHANICAL ALLOYING AND LEAD CONTENT ON MICROSTRUCTURE, HARDNESS AND TRIBOLOGICAL BEHAVIOR OF 6061 ALUMINIUM ALLOYS

Directory of Open Access Journals (Sweden)

M. Paidpilli

2017-03-01

Full Text Available In the present work, one batch of prealloyed 6061Al powder was processed by mixing and another one was ball milled with varying amount of lead content (0-15 vol. %. These powders were compacted at 300MPa and sintered at 590˚C under N2. The instrumented hardness and the young’s modulus of as-sintered 6061Al-Pb alloys were examined as a function of lead content and processing route. The wear test under dry sliding condition has been performed at varying loads (10-40 N using pin-on-disc tribometer. The microstructure and worn surfaces have been investigated using SEM to evaluate the change in topographical features due to mechanical alloying and lead content. The mechanically alloyed materials showed improved wear characteristics as compared to as-mixed counterpart alloys. Delamination of 6061Al-Pb alloys decreases up to an optimum lead composition in both as-mixed and ball-milled 6061Al-Pb alloys. The results indicated minimum wear rate for as-mixed and ball-milled 6061Al alloy at 5 and 10 vol. % Pb, respectively.

AW-101 entrained solids - Solubility versus temperature

International Nuclear Information System (INIS)

GJ Lumetta; RC Lettau; GF Piepel

2000-01-01

This report describes the results of a test conducted by Battelle to assess the solubility of the solids entrained in the diluted AW-101 low-activity waste (LAW) sample. BNFL requested Battelle to dilute the AW-1-1 sample using de-ionized water to mimic expected plant operating conditions. BNFL further requested Battelle to assess the solubility of the solids present in the diluted AW-101 sample versus temperature conditions of 30, 40, and 50 C. BNFL requested these tests to assess the composition of the LAW supernatant and solids versus expected plant-operating conditions. The work was conducted according to test plan BNFL-TP-29953-7, Rev. 0, Determination of the Solubility of LAW Entrained Solids. The test went according to plan, with no deviations from the test plan

20 CFR 606.1 - Purpose and scope.

Science.gov (United States)

2010-04-01

... standards for grant of such relief in the form of— (i) A cap on tax credit reduction, (ii) Avoidance of tax... Employees' Benefits EMPLOYMENT AND TRAINING ADMINISTRATION, DEPARTMENT OF LABOR TAX CREDITS UNDER THE FEDERAL UNEMPLOYMENT TAX ACT; ADVANCES UNDER TITLE XII OF THE SOCIAL SECURITY ACT General § 606.1 Purpose...

Cold metal transfer spot plug welding of AA6061-T6-to-galvanized steel for automotive applications

International Nuclear Information System (INIS)

Cao, R.; Huang, Q.; Chen, J.H.; Wang, Pei-Chung

2014-01-01

Highlights: • Two Al-to-galvanized steel spot plug welding joints were studied by CMT method. • The optimum process variables for the two joints were gotten by orthogonal test. • Connection mechanism of the two joints were discussed. -- Abstract: In this study, cold metal transfer (CMT) spot plug joining of 1 mm thick Al AA6061-T6 to 1 mm thick galvanized steel (i.e., Q235) was studied. Welding variables were optimized for a plug weld in the center of a 25 mm overlap region with aluminum 4043 wire and 100% argon shielding gas. Microstructures and elemental distributions were characterized by scanning electron microscopy with energy dispersive X-ray spectrometer. Mechanical testing of CMT spot plug welded joints was conducted. It was found that it is feasible to join Al AA6061T6-to-galvanized steel by CMT spot plug welding method. The process variables for two joints with Al AA6061T6-to-galvanized mild steel and galvanized mild steel-to-Al AA6061T6 are optimized. The strength of CMT spot welded Al AA6061T6-to-galvanized mild steel is determined primarily by the strength and area of the brazed interface. While, the strength of the galvanized mild steel-to-Al AA6061T6 joint is mainly dependent upon the area of the weld metal

Mechanical and thermal properties of phthalonitrile resin reinforced with silicon carbide particles

International Nuclear Information System (INIS)

Derradji, Mehdi; Ramdani, Noureddine; Zhang, Tong; Wang, Jun; Feng, Tian-tian; Wang, Hui; Liu, Wen-bin

2015-01-01

Highlights: • SiC microparticles improve the mechanical properties of phthalonitrile resin. • Excellent thermal stability achieved by adding SiC particles in phthalonitrile resin. • Adding 20 wt.% of SiC microparticles increases the T g by 38 °C. • Silane coupling agent can enhance the adhesion and dispersion of particles/matrix. - Abstract: A new type of composite based on phthalonitrile resin reinforced with silicon carbide (SiC) microparticles was prepared. For various weight ratios ranging between 0% and 20%, the effect of the micro-SiC particles on the mechanical and thermal properties has been studied. Results from thermal analysis revealed that the starting decomposition temperature and the residual weight were significantly improved upon adding the reinforcing phase. At the maximum micro-SiC loading, dynamic mechanical analysis (DMA) showed an important enhancement in both the storage modulus and glass transition temperature (T g ), reaching 3.1 GPa and 338 °C, respectively. The flexural strength and modulus as well as the microhardness were significantly enhanced by adding the microfillers. Tensile test revealed enhancements in the composites toughness upon adding the microparticles. Polarization optical microscope (POM) and scanning electron microscope (SEM) analysis confirmed that mechanical and thermal properties improvements are essentially attributed to the good dispersion and adhesion between the particles and the resin

Study of corrosion processes on Al-AA 6061 crevices immersed in high purity water and sodium citrate solution

International Nuclear Information System (INIS)

Rodriguez, Sebastian A.; Haddad, Roberto; Lanzani, Liliana A.

2004-01-01

An experimental approach has been developed to study the corrosion behavior of artificial crevices manufactured with high purity aluminum and AA 6061 alloy, immersed in dematerialised water and sodium citrate solution (96,5 μS/cm). Alkaline attack was found on the surrounding of iron rich particles in the external zone of the crevice, as a result of localized oxygen reduction reaction on these sites. This attack was not observed in the zone inside the crevice. Study of the phase Mg 2 Si by EDS allowed establishing that there is not preferential dissolution inside the crevice. The formation of a stable and non-soluble complex between Al and citrate anion inhibited the production of Al(OH) 3 precipitate, which was observed on the surface of specimens immersed in pure water. Investigations of the aluminum oxide evolution on AA 6061 surfaces in water showed that it was composed by two layers: an internal one made of Bohemite and an external one in direct contact with the water, with a Bayerite structure. The surface analysis was accomplished using XR, OM and SEM techniques. (author) [es

Microstructure and strain rate effects on the mechanical behavior of particle reinforced epoxy-based reactive materials

Science.gov (United States)

White, Bradley William

The effects of reactive metal particles on the microstructure and mechanical properties of epoxy-based composites is investigated in this work. Particle reinforced polymer composites show promise as structural energetic materials that can provide structural strength while simultaneously being capable of releasing large amounts of chemical energy through highly exothermic reactions occurring between the particles and with the matrix. This advanced class of materials is advantageous due to the decreased amount of high density inert casings needed for typical energetic materials and for their ability to increase payload expectancy and decrease collateral damage. Structural energetic materials can be comprised of reactive particles that undergo thermite or intermetallic reactions. In this work nickel (Ni) and aluminum (Al) particles were chosen as reinforcing constituents due to their well characterized mechanical and energetic properties. Although, the reactivity of nickel and aluminum is well characterized, the effects of their particle size, volume fractions, and spatial distribution on the mechanical behavior of the epoxy matrix and composite, across a large range of strain rates, are not well understood. To examine these effects castings of epoxy reinforced with 20--40 vol.% Al and 0--10 vol.% Ni were prepared, while varying the aluminum nominal particle size from 5 to 50 mum and holding the nickel nominal particle size constant at 50 mum. Through these variations eight composite materials were produced, possessing unique microstructures exhibiting different particle spatial distributions and constituent makeup. In order to correlate the microstructure to the constitutive response of the composites, techniques such as nearest-neighbor distances, and multiscale analysis of area fractions (MSAAF) were used to quantitatively characterize the microstructures. The composites were investigated under quasi-static and dynamic compressive loading conditions to characterize

Investigations of Effect of Rotary EDM Electrode on Machining Performance of Al6061 Alloy

Science.gov (United States)

Robinson Smart, D. S.; Jenish Smart, Joses; Periasamy, C.; Ratna Kumar, P. S. Samuel

2018-04-01

Electric Discharge Machining is an essential process which is being used for machining desired shape using electrical discharges which creates sparks. There will be electrodes subjected to electric voltage and which are separated by a dielectric liquid. Removing of material will be due to the continuous and rapid current discharges between two electrodes.. The spark is very carefully controlled and localized so that it only affects the surface of the material. Usually in order to prevent the defects which are arising due to the conventional machining, the Electric Discharge Machining (EDM) machining is preferred. Also intricate and complicated shapes can be machined effectively by use of Electric Discharge Machining (EDM). The EDM process usually does not affect the heat treat below the surface. This research work focus on the design and fabrication of rotary EDM tool for machining Al6061alloy and investigation of effect of rotary tool on surface finish, material removal rate and tool wear rate. Also the effect of machining parameters of EDM such as pulse on & off time, current on material Removal Rate (MRR), Surface Roughness (SR) and Electrode wear rate (EWR) have studied. Al6061 alloy can be used for marine and offshore applications by reinforcing some other elements. The investigations have revealed that MRR (material removal rate), surface roughness (Ra) have been improved with the reduction in the tool wear rate (TWR) when the tool is rotating instead of stationary. It was clear that as rotary speed of the tool is increasing the material removal rate is increasing with the reduction of surface finish and tool wear rate.

Particle reinforced composites from acrylamide modified blend of styrene-butadiene and natural rubber

Science.gov (United States)

Blends of styrene-butadiene rubber and natural rubber that provide balanced properties were modified with acrylamide and reinforced with soy protein particles. The rubber composites show improved mechanical properties. Both modified rubber and composites showed a faster curing rate. The crosslinking...

Processing and Characterization of NiTi Shape Memory Alloy Particle Reinforced Sn-In Solders

National Research Council Canada - National Science Library

Chung, Kohn C

2006-01-01

.... In previous work, it was proposed that reinforcement of solder by NiTi shape memory alloy particles to form smart composite solder reduces the inelastic strain of the solder and hence, may enhance...

Impact Strength of Composite Materials Based on EN AC-44200 Matrix Reinforced with Al2O3 Particles

Directory of Open Access Journals (Sweden)

Kurzawa A.

2017-09-01

Full Text Available The paper presents the results of research of impact strength of aluminum alloy EN AC-44200 based composite materials reinforced with alumina particles. The research was carried out applying the materials produced by the pressure infiltration method of ceramic preforms made of Al2O3 particles of 3-6μm with the liquid EN AC-44200 Al alloy. The research was aimed at determining the composite resistance to dynamic loads, taking into account the volume of reinforcing particles (from 10 to 40% by volume at an ambient of 23°C and at elevated temperatures to a maximum of 300°C. The results of this study were referred to the unreinforced matrix EN AC-44200 and to its hardness and tensile strength. Based on microscopic studies, an analysis and description of crack mechanics of the tested materials were performed. Structural analysis of a fracture surface, material structures under the crack surfaces of the matrix and cracking of the reinforcing particles were performed.

Fabrication of AA6061-T6 Plate Type Fuel Assembly Using Electron Beam Welding Process

International Nuclear Information System (INIS)

Kim, Soosung; Seo, Kyoungseok; Lee, Donbae; Park, Jongman; Lee, Yoonsang; Lee, Chongtak

2014-01-01

AA6061-T6 aluminum alloy is easily welded by conventional GTAW (Gas Tungsten Arc Welding), LBW (Laser Beam Welding) and EBW. However, certain characteristics, such as solidification cracking, porosity, HAZ (Heat-affected Zone) degradation must be considered during welding. Because of high energy density and low heat input, especially LBW and EBW processes possess the advantage of minimizing the fusing zone and HAZ and producing deeper penetration than arc welding processes. In present study, to apply for the nuclear fuel plate fabrication and assembly, a fundamental EBW experiment using AA6061-T6 aluminum alloy specimens was conducted. Furthermore, to establish the welding process, and satisfy the requirements of the weld quality, EBW apparatus using an electron welding gun and vacuum chamber was developed, and preliminary investigations for optimizing the welding parameters of the specimens using AA6061-T6 aluminum plates were also performed. The EB weld quality of AA6061-T6 aluminum alloy for the fuel plate assembly has been also studied by the shrinkage measurement and weld inspection using computed tomography. This study was carried out to determine the suitable welding parameters and to evaluate tensile strength of AA6061-T6 aluminum alloy. In the present experiment, satisfactory electron beam welding process of the full-sized sample was being developed. Based on this fundamental study, fabrication of the plate-type fuel assembly will be provided for the future Ki-Jang research reactor project

Microstructure and mechanical properties of Al-Mg-Si-Cu matrix composites reinforced with AINp. processed by extrusion of powders

International Nuclear Information System (INIS)

Ortiz, J. L.; Amigo, V.; Salvador, M. D.; Perz, C. R.

2000-01-01

This article presents an experimental investigation on the structure and mechanical properties of an Al-Mg-Si-Cu P/M alloy reinforced with 5%, 10% and 15% aluminum nitride, produced by extrusion of cold compacted powders mixtures. Mechanical properties in as extruded and T6 conditions are compared. Differential Scanning Calorimetry and Dilatometric analysis were conducted to gain further insight into the precipitation process of these materials. Low cost 6061 Al/AINp composites can be produced with rate and small porosity by extrusion of cold compacted shapes without canning. The mechanical properties of the MMCs obtained by this process have limitations for high particles fractions because of clustering effects. All materials are always harder than the matrix and shows a similar behavior during aging processes but kinetics is changed. Potential applications of dilatometric techniques in the aging investigations of aluminum alloys and aluminum matrix composites have been established. (Author) 23 refs

Investigation of Tank 241-AW-104 Composite Floating Layer

Energy Technology Data Exchange (ETDEWEB)

Meznarich, H. K. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Bolling, S. D. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Lachut, J. S. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States); Cooke, G. A. [Washington River Protection Solutions LLC (WRPS), Richland, WA (United States)

2018-02-27

Seven grab samples and one field blank were taken from Tank 241-AW-104 (AW-104) on June 2, 2017, and received at 222-S Laboratory on June 5, 2017. A visible layer with brown solids was observed floating on the top of two surface tank waste samples (4AW-17-02 and 4AW 17 02DUP). The floating layer from both samples was collected, composited, and submitted for chemical analyses and solid phase characterization in order to understand the composition of the floating layer. Tributyl phosphate and tridecane were higher in the floating layer than in the aqueous phase. Density in the floating layer was slightly lower than the mean density of all grab samples. Sodium nitrate and sodium carbonate were major components with a trace of gibbsite and very small size agglomerates were present in the solids of the floating layer. The supernate consisted of organics, soluble salt, and particulates.

Wear Response of Aluminium 6061 Composite Reinforced with Red Mud at Elevated Temperature

Directory of Open Access Journals (Sweden)

R. Dabral

2017-09-01

Full Text Available The present work is focused on the investigations on dry sliding wear behaviour of aluminium metal matrix composite at room and elevated temperature. Aluminium metal matrix composites reinforced with red mud are prepared by stir casting method. The experiments are planned using Taguchi technique. An orthogonal array, analysis of variance and signal to noise ratio are used to check the influence of wear parameters like temperature, percentage of reinforcement, mesh size, load, sliding distance and sliding speed on dry sliding wear of composites. The optimal testing parameters are found and their values are calculated which are then compared with predicted values. A reasonable agreement is found between predicted and actual values. The model prepared in the present work can be effectively used to predict the specific wear rate of the composites.

Micromechanical analysis of a hybrid composite—effect of boron carbide particles on the elastic properties of basalt fiber reinforced polymer composite

Science.gov (United States)

Krishna Golla, Sai; Prasanthi, P.

2016-11-01

A fiber reinforced polymer (FRP) composite is an important material for structural application. The diversified application of FRP composites has become the center of attention for interdisciplinary research. However, improvements in the mechanical properties of this class of materials are still under research for different applications. The reinforcement of inorganic particles in a composite improves its structural properties due to their high stiffness. The present research work is focused on the prediction of the mechanical properties of the hybrid composites where continuous fibers are reinforced in a micro boron carbide particle mixed polypropylene matrix. The effectiveness of the addition of 30 wt. % of boron carbide (B4C) particle contributions regarding the longitudinal and transverse properties of the basalt fiber reinforced polymer composite at various fiber volume fractions is examined by finite element analysis (FEA). The experimental approach is the best way to determine the properties of the composite but it is expensive and time-consuming. Therefore, the finite element method (FEM) and analytical methods are the viable methods for the determination of the composite properties. The FEM results were obtained by adopting a micromechanics approach with the support of FEM. Assuming a uniform distribution of reinforcement and considering one unit-cell of the whole array, the properties of the composite materials are determined. The predicted elastic properties from FEA are compared with the analytical results. The results suggest that B4C particles are a good reinforcement for the enhancement of the transverse properties of basalt fiber reinforced polypropylene.

Super Polishing of Aluminum 6061-T6 Mirrors, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — An innovative 2D super-polishing process for Aluminum 6061-T6 planar mirrors which removes diamond point turning (DPT) grooves and attains rms surface finishes below...

Effect of thermal tempering on microstructure and mechanical properties of Mg-AZ31/Al-6061 diffusion bonding

Energy Technology Data Exchange (ETDEWEB)

Jafarian, Mojtaba [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Rizi, Mohsen Saboktakin, E-mail: M.saboktakin@Pa.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Jafarian, Morteza [Young Researchers and Elite Club, Science and Research Branch, Islamic Azad University, Tehran (Iran, Islamic Republic of); Honarmand, Mehrdad [Department of Mechanical Engineering, Tiran Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Javadinejad, Hamid Reza; Ghaheri, Ali [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of); Bahramipour, Mohammad Taghi [Materials Engineering Department, Hakim Sabzevari University, Sabzevar, 397 (Iran, Islamic Republic of); Ebrahimian, Marzieh [Department of Materials Engineering, Isfahan University of Technology, Isfahan 8415683111 (Iran, Islamic Republic of); Department of Industrial Engineering, Lenjan Branch, Islamic Azad University, Isfahan (Iran, Islamic Republic of)

2016-06-01

The objective of this study is to investigate the effect of the types thermal tempering of aluminum alloy on microstructure and mechanical properties of AZ31-O Mg and Al 6061-T6 diffusion bonding. Using Optical Microscope (OM) and Scanning Electron Microscopes (SEM) equipped with EDS analysis and line scan the interfaces of joints were evaluated. The XRD analysis was carried out to characterize phase constitution near the interface zone. The mechanical properties of joints were measured using Vickers micro-hardness and shear strength. According to the results in bonding of AZ31-Mg/Al-6061-O, in less plastic deformation in magnesium alloy, diffusion rate of most magnesium atoms occurred to aluminum alloy and formation of diffusion zone with minimum micro-hardness (140 HV) and maximum shear strength (32 MPa) compared to Al 6061-T6/Mg-AZ31 bonding. Evaluation of fracture surfaces indicates an occurrence of failure from the brittle intermetallic phases. - Highlights: • Diffusion bonding AZ31 to Al-6061withoutany interlayer was successful. • Thermal tempered aluminum alloy plays a vital role in the mechanical properties of joint. • Less thickness of reaction layers and micro-hardness in bonding annealed Al- 6061 layers to AZ31 was achieved. • Fracture surfaces indicated that the onset of fracture from intermetallic compounds resulted in fracture of the cleavage.

Effect of thermal tempering on microstructure and mechanical properties of Mg-AZ31/Al-6061 diffusion bonding

International Nuclear Information System (INIS)

Jafarian, Mojtaba; Rizi, Mohsen Saboktakin; Jafarian, Morteza; Honarmand, Mehrdad; Javadinejad, Hamid Reza; Ghaheri, Ali; Bahramipour, Mohammad Taghi; Ebrahimian, Marzieh

2016-01-01

The objective of this study is to investigate the effect of the types thermal tempering of aluminum alloy on microstructure and mechanical properties of AZ31-O Mg and Al 6061-T6 diffusion bonding. Using Optical Microscope (OM) and Scanning Electron Microscopes (SEM) equipped with EDS analysis and line scan the interfaces of joints were evaluated. The XRD analysis was carried out to characterize phase constitution near the interface zone. The mechanical properties of joints were measured using Vickers micro-hardness and shear strength. According to the results in bonding of AZ31-Mg/Al-6061-O, in less plastic deformation in magnesium alloy, diffusion rate of most magnesium atoms occurred to aluminum alloy and formation of diffusion zone with minimum micro-hardness (140 HV) and maximum shear strength (32 MPa) compared to Al 6061-T6/Mg-AZ31 bonding. Evaluation of fracture surfaces indicates an occurrence of failure from the brittle intermetallic phases. - Highlights: • Diffusion bonding AZ31 to Al-6061withoutany interlayer was successful. • Thermal tempered aluminum alloy plays a vital role in the mechanical properties of joint. • Less thickness of reaction layers and micro-hardness in bonding annealed Al- 6061 layers to AZ31 was achieved. • Fracture surfaces indicated that the onset of fracture from intermetallic compounds resulted in fracture of the cleavage.

Probabilistic homogenization of random composite with ellipsoidal particle reinforcement by the iterative stochastic finite element method

Science.gov (United States)

Sokołowski, Damian; Kamiński, Marcin

2018-01-01

This study proposes a framework for determination of basic probabilistic characteristics of the orthotropic homogenized elastic properties of the periodic composite reinforced with ellipsoidal particles and a high stiffness contrast between the reinforcement and the matrix. Homogenization problem, solved by the Iterative Stochastic Finite Element Method (ISFEM) is implemented according to the stochastic perturbation, Monte Carlo simulation and semi-analytical techniques with the use of cubic Representative Volume Element (RVE) of this composite containing single particle. The given input Gaussian random variable is Young modulus of the matrix, while 3D homogenization scheme is based on numerical determination of the strain energy of the RVE under uniform unit stretches carried out in the FEM system ABAQUS. The entire series of several deterministic solutions with varying Young modulus of the matrix serves for the Weighted Least Squares Method (WLSM) recovery of polynomial response functions finally used in stochastic Taylor expansions inherent for the ISFEM. A numerical example consists of the High Density Polyurethane (HDPU) reinforced with the Carbon Black particle. It is numerically investigated (1) if the resulting homogenized characteristics are also Gaussian and (2) how the uncertainty in matrix Young modulus affects the effective stiffness tensor components and their PDF (Probability Density Function).

Fabrication of metal matrix composite by semi-solid powder processing

Energy Technology Data Exchange (ETDEWEB)

Wu, Yufeng [Iowa State Univ., Ames, IA (United States)

2011-01-01

compositional properties of the Al6061-CNT composites. A shear lag model was applied to predict the mechanical property (hardness) of the composite. This work demonstrated the promising potential of SPP in the fabrication of particle/fiber (nanotube) reinforced MMCs.

Numerical simulation of aluminum alloy 6061 micro-mold fabrication for the production of polymeric microstructures by micro-hot-embossing

International Nuclear Information System (INIS)

Tran, N K; Chester, Shawn A; Lam, Y C; Anand, L; Yue, C Y

2012-01-01

Micro-molds play an important role in the manufacturing process of polymeric micro-devices, e.g. microfluidic devices, as they determine the product quality and the overall production cost. We report here the applicability of a large-deformation, high-temperature, isotropic elastic-viscoplasticity model for the prediction of micron-scale hot-embossing of AA6061. The material parameters in the constitutive model were determined by fitting the stress–strain curves from compression tests at various temperatures and strain rates. The constitutive theory was implemented in a finite element program, and the numerical simulation capability was validated by predicting the response of AA6061 in some representative macro-scale experiments; these experiments had not been used for the determination of the material parameters in the constitutive model. Additional micron-scale hot-embossing experiments on AA6061 were conducted, and by comparing the numerical simulation results to the corresponding physical experiments, we demonstrate that the deformation evolution of AA6061 during micro-hot-embossing is well predicted. The constitutive model and its numerical implementation open the possibility of optimizing the process of making micro-molds for microfluidic devices from AA6061. (paper)

Synthesis and Characterization of Hybrid Silica-Zirconia Coatings with Cerium Inhibitor on Aluminum 6061

Directory of Open Access Journals (Sweden)

M. Bahrami

2016-12-01

Full Text Available Organic–inorganic hybrid coatings were prepared by sol–gel method and deposited on aluminum alloy 6061. Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR spectroscopy and Scanning Electron Microscopy (SEM were used for structural study of the hybrid coatings. Adhesive strength of sol–gel coatings to the substrate was evaluated quantitatively and qualitatively. Corrosion behavior of the samples was studied by cyclic potentiodynamic and linear polarization tests. Results showed that adhesion strength of the coatings to the substrates was increased with increasing tetrapropoxide of zirconium (TPOZ and cerium content. Corrosion tests showed that corrosion current density of coated samples were decreased three to seven orders of magnitude in comparison with uncoated aluminum alloy 6061. Decreasing in corrosion current density and increasing in polarization resistance was observed by increasing zirconia and cerium content. Unlike the uncoated aluminum alloy 6061, the crack-free coatings did not show pitting tendency. 

Decay resistance of wood-plastic composites reinforced with extracted or delignified wood flour

Science.gov (United States)

Rebecca E. Ibach; Yao Chen; Nicole M. Stark; Mandla A. Tshabalala; Yongming Fan; Jianmin Gao

2014-01-01

The moisture and decay resistance of wood-plastic composites (WPCs) reinforced with extracted or delignified wood flour (WF) was investigated. Three different extractions were preformed: toluene/ethanol (TE), acetone/water (AW), and hot water (HW). Delignification (DL) was performed using a sodium chlorite/acetic acid solution. All WPCs specimens were made with 50% by...

Machinability of Al 6061 Deposited with Cold Spray Additive Manufacturing

Science.gov (United States)

Aldwell, Barry; Kelly, Elaine; Wall, Ronan; Amaldi, Andrea; O'Donnell, Garret E.; Lupoi, Rocco

2017-10-01

Additive manufacturing techniques such as cold spray are translating from research laboratories into more mainstream high-end production systems. Similar to many additive processes, finishing still depends on removal processes. This research presents the results from investigations into aspects of the machinability of aluminum 6061 tubes manufactured with cold spray. Through the analysis of cutting forces and observations on chip formation and surface morphology, the effect of cutting speed, feed rate, and heat treatment was quantified, for both cold-sprayed and bulk aluminum 6061. High-speed video of chip formation shows changes in chip form for varying material and heat treatment, which is supported by the force data and quantitative imaging of the machined surface. The results shown in this paper demonstrate that parameters involved in cold spray directly impact on machinability and therefore have implications for machining parameters and strategy.

An Assessment of Mechanical and Tribological Property of Hybrid Aluminium Metal Matrix Composite

Directory of Open Access Journals (Sweden)

R. Santosh Kumar

2017-04-01

Full Text Available Composite materials has huge requirement in the area of automobile, aerospace, and wear resistant applications. This study presents the synthesis of composite reinforced with SiC and Al2O3 using gravity stir casting. Stir casting is the manufacturing process that is incorporated to produce the composite material because of its extreme bonding capacity with base material. The composition of reinforcement with 6061 aluminium matrix is SiC-7.5% and Al2O3 -2.5% respectively. The average size of reinforcement particle is 30-40 microns. The synthesised composite casting is machined using EDM to prepare specimens for various tests. Microstructure study was carried and the microstructure images prove the existence and dispersion of reinforcement particles in the metal matrix. There is no visible porosity is observed. The hardness of the specimen is tested using Vickers hardness tester and found considerable increase when compare with parent alloy Al 6061. Also mechanical and tribological properties of hybrid Aluminium metal matrix composite were employed. The fortifying material, Silicon Carbide is composed of tetrahedral of carbon and silicon atoms with strong bonds in crystal lattice along with its excellent wear resistance property and alumina have high strength and wear resistance. To avoid enormous material wastage and to achieve absolute accuracy, wire-cut EDM process is capitalised to engrave the specimen as per required dimensions. Three Tensile test specimens were prepared, in order to achieve reliability in results as per ASTM- E8 standard, and the values were tabulated. Impact test was carried out and the readings were tabulated. Wear test was carried out using pin on disc wear test apparatus and the results show considerable increase in wear resistant property when compare with parent alloy Al6061.The above work proves the successful fabrication of composite and evaluation of properties.

241-AW Tank Farm Construction Extent of Condition Review for Tank Integrity

Energy Technology Data Exchange (ETDEWEB)

Barnes, Travis J.; Gunter, Jason R.; Reeploeg, Gretchen E.

2013-11-19

This report provides the results of an extent of condition construction history review for the 241-AW tank farm. The construction history of the 241-AW tank farm has been reviewed to identify issues similar to those experienced during tank AY-102 construction. Those issues and others impacting integrity are discussed based on information found in available construction records, using tank AY-102 as the comparison benchmark. In the 241-AW tank farm, the fourth double-shell tank farm constructed, similar issues as those with tank 241-AY-102 construction occured. The overall extent of similary and affect on 241-AW tank farm integrity is described herein.

Al-based metal matrix composites reinforced with Al–Cu–Fe quasicrystalline particles: Strengthening by interfacial reaction

International Nuclear Information System (INIS)

Ali, F.; Scudino, S.; Anwar, M.S.; Shahid, R.N.; Srivastava, V.C.; Uhlenwinkel, V.; Stoica, M.; Vaughan, G.; Eckert, J.

2014-01-01

Highlights: • Strength of composites is enhanced as the QC-to-ω phase transformation advances. • Yield strength increases from 195 to 400 MPa with QC-to-ω interfacial reaction. • Reducing matrix ligament size explains most of the strengthening. • Improved interfacial bonding and nano ω phase explains divergence from model. - Abstract: The interfacial reaction between the Al matrix and the Al 62.5 Cu 25 Fe 12.5 quasicrystalline (QC) reinforcing particles to form the Al 7 Cu 2 Fe ω-phase has been used to further enhance the strength of the Al/QC composites. The QC-to-ω phase transformation during heating was studied by in situ X-ray diffraction using a high-energy monochromatic synchrotron beam, which permits to follow the structural evolution and to correlate it with the mechanical properties of the composites. The mechanical behavior of these transformation-strengthened composites is remarkably improved as the QC-to-ω phase transformation progresses: the yield strength increases from 195 MPa for the starting material reinforced exclusively with QC particles to 400 MPa for the material where the QC-to-ω reaction is complete. The reduction of the matrix ligament size resulting from the increased volume fraction of the reinforcing phase during the transformation can account for most of the observed improvement in strength, whereas the additional strengthening can be ascribed to the possible presence of nanosized ω-phase particles as well as to the improved interfacial bonding between matrix and particles caused by the compressive stresses arising in the matrix

Al-based metal matrix composites reinforced with Al–Cu–Fe quasicrystalline particles: Strengthening by interfacial reaction

Energy Technology Data Exchange (ETDEWEB)

Ali, F. [IFW Dresden, Institut für Komplexe Materialien, Postfach 27 01 16, D-01171 Dresden (Germany); Materials Processing Group, DMME, Pakistan Institute of Engineering and Applied Sciences, P.O. Nilore, Islamabad (Pakistan); Scudino, S., E-mail: s.scudino@ifw-dresden.de [IFW Dresden, Institut für Komplexe Materialien, Postfach 27 01 16, D-01171 Dresden (Germany); Anwar, M.S.; Shahid, R.N. [Materials Processing Group, DMME, Pakistan Institute of Engineering and Applied Sciences, P.O. Nilore, Islamabad (Pakistan); Srivastava, V.C. [Metal Extraction and Forming Division, National Metallurgical Laboratory, Jamshedpur 831007 (India); Uhlenwinkel, V. [Institut für Werkstofftechnik, Universität Bremen, D-28359 Bremen (Germany); Stoica, M. [IFW Dresden, Institut für Komplexe Materialien, Postfach 27 01 16, D-01171 Dresden (Germany); Vaughan, G. [European Synchrotron Radiation Facilities ESRF, BP 220, 38043 Grenoble (France); Eckert, J. [IFW Dresden, Institut für Komplexe Materialien, Postfach 27 01 16, D-01171 Dresden (Germany); TU Dresden, Institut für Werkstoffwissenschaft, D-01062 Dresden (Germany)

2014-09-01

Highlights: • Strength of composites is enhanced as the QC-to-ω phase transformation advances. • Yield strength increases from 195 to 400 MPa with QC-to-ω interfacial reaction. • Reducing matrix ligament size explains most of the strengthening. • Improved interfacial bonding and nano ω phase explains divergence from model. - Abstract: The interfacial reaction between the Al matrix and the Al{sub 62.5}Cu{sub 25}Fe{sub 12.5} quasicrystalline (QC) reinforcing particles to form the Al{sub 7}Cu{sub 2}Fe ω-phase has been used to further enhance the strength of the Al/QC composites. The QC-to-ω phase transformation during heating was studied by in situ X-ray diffraction using a high-energy monochromatic synchrotron beam, which permits to follow the structural evolution and to correlate it with the mechanical properties of the composites. The mechanical behavior of these transformation-strengthened composites is remarkably improved as the QC-to-ω phase transformation progresses: the yield strength increases from 195 MPa for the starting material reinforced exclusively with QC particles to 400 MPa for the material where the QC-to-ω reaction is complete. The reduction of the matrix ligament size resulting from the increased volume fraction of the reinforcing phase during the transformation can account for most of the observed improvement in strength, whereas the additional strengthening can be ascribed to the possible presence of nanosized ω-phase particles as well as to the improved interfacial bonding between matrix and particles caused by the compressive stresses arising in the matrix.

Nanoparticle dispersion effect of laser-surface melting in ZrB{sub 2p}/6061Al composites

Energy Technology Data Exchange (ETDEWEB)

Zeng, Yida; Chao, Yuhjin; Luo, Zhen, E-mail: lz-tju@163.com [Tianjin University, School of Material Science and Engineering (China); Huang, Yongxian [State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology (China)

2017-04-15

Zirconium diboride (ZrB{sub 2p}, 15 vol%)/6061 aluminum (Al) composites were fabricated via in situ reaction. The existence, morphologies, and dispersion degree of the in situ ZrB{sub 2} particles with size from tens to hundreds of nanometers were studied by X-ray diffractometry, energy-dispersive X-ray spectroscopy, field-emission scanning electron microscopy, and high-resolution transmission electron microscopy. As the particle-settlement effect becomes dominant during the composite fabrication process, ZrB{sub 2} nanoparticles agglomerate to a certain extent in some areas of the as-cast composites. A laser-surface melting (LSM) strategy was applied to disperse agglomerated ZrB{sub 2} nanoparticles in as-cast composites, and the ZrB{sub 2} nanoparticle dispersion is affected visibly by LSM. After LSM, nanoparticles tend to distribute along the grain boundary. Particle clusters were dispersed in an explosive orientation and the particle diffusion distance varied in terms of its radius and melt-viscosity vicinity. High-resolution transmission electron microscopy showed the existence of a subgrain structure near the ZrB{sub 2}–Al interface after LSM. This may increase the yield strength when a dislocation tangle forms.

Characterisation of glass matrix composites reinforced with lead zirconate titanate particles

International Nuclear Information System (INIS)

Cannillo, Valeria; Manfredini, Tiziano; Montorsi, Monia; Tavoni, Francesca; Minay, Emma J.; Boccaccini, Aldo R.

2005-01-01

A new type of glass matrix composite reinforced with ferroelectric particulate secondary phase was investigated. Samples containing lead zirconate titanate (PZT) particles in a silicate lead glass were fabricated. Various sintering strategies were tested in order to optimise the processing route. The densest samples were obtained by hot-pressing. The composites were characterized by means of SEM observations, X-ray diffraction, differential thermal analysis and Vickers indentations. In order to get a deeper insight into the thermo-mechanical behaviour of the material, a FEM based numerical model was prepared and applied. In particular, the crack-particle interaction was assessed and thus possible toughening mechanisms were investigated. By means of the numerical modelling supported by SEM observations, traditional toughening mechanisms (e.g. crack deflection, particle debonding) were ruled out. Since the experimentally measured indentation fracture toughness of the composite is significantly higher than that of the unreinforced glass, the findings suggest that a new toughening mechanism may be active, based on the piezoelectric effect

Effects of pH and chloride concentration on pitting corrosion of AA6061 aluminum alloy

International Nuclear Information System (INIS)

Zaid, B.; Saidi, D.; Benzaid, A.; Hadji, S.

2008-01-01

Effects of pH solution and chloride (Cl - ) ion concentration on the corrosion behaviour of alloy AA6061 immersed in aqueous solutions of NaCl have been investigated using measurements of weight loss, potentiodynamic polarisation, linear polarisation, cyclic polarisation experiment combined with open circuit potential transient technique and optical or scanning electron microscopy. The corrosion behaviour of the AA6061 aluminum alloy was found to be dependant on the pH and chloride concentration [NaCl] of solution. In acidic or slightly neutral solutions, general and pitting corrosion occurred simultaneously. In contrast, exposure to alkaline solutions results in general corrosion. Experience revealed that the alloy AA6061 was susceptible to pitting corrosion in all chloride solution of concentration ranging between 0.003 wt% and 5.5 wt% NaCl and an increase in the chloride concentration slightly shifted both the pitting E pit and corrosion E cor potentials to more active values. In function of the conditions of treatment, the sheets of the alloy AA6061 undergo two types of localised corrosion process, leading to the formation of hemispherical and crystallographic pits. Polarisation resistance measurements in acidic (pH = 2) and alkaline chloride solutions (pH = 12) which are in good agreement with those of weight loss, show that the corrosion kinetic is minimised in slightly neutral solutions (pH = 6)

Evaluation of Electron Beam Welding Performance of AA6061-T6 Plate-type Fuel Assembly

International Nuclear Information System (INIS)

Kim, Soo-Sung; Seo, Kyoung-Seok; Lee, Don-Bae; Park, Jong-Man; Lee, Yoon-Sang; Lee, Chong-Tak

2014-01-01

As one of the most commonly used heat-treatable aluminum alloys, AA6061-T6 aluminum alloy is available in a wide range of structural materials. Typically, it is used in structural members, auto-body sheet and many other applications. Generally, this alloy is easily welded by conventional GTAW (Gas Tungsten Arc Welding), LBW (Laser Beam Welding) and EBW(Electron Beam Welding). However, certain characteristics, such as solidification cracking, porosity, HAZ (Heat-affected Zone) degradation must be considered during welding. Because of high energy density and low heat input, especially LBW and EBW processes possess the advantage of minimizing the fusing zone and HAZ and producing deeper penetration than arc welding processes. In present study, to apply for the plate-type nuclear fuel fabrication and assembly, a fundamental electron beam welding experiment using AA6061-T6 aluminum alloy specimens was conducted. Furthermore, to establish the suitable welding process, and satisfy the requirements of the weld quality, EBW apparatus using an electron welding gun and vacuum chamber was developed, and preliminary investigations for optimizing the welding parameters of the specimens using AA6061-T6 aluminum plates were also performed. The EB weld quality of AA6061-T6 aluminum alloy for the plate-type fuel assembly has been also studied by the weld penetrations of side plate to end fitting and fixing bar and weld inspections using computed tomography

Aluminum alloy production for the reinforcement of the CMS conductor

CERN Document Server

Sequeira-Lopes-Tavares, S; Campi, D; Curé, B; Horváth, I L; Riboni, P; Sgobba, Stefano; Smith, R P

2002-01-01

The Compact Muon Solenoid (CMS) is one of the general-purpose detectors to be provided for the Large Hadron Collider (LHC) project at CERN. The design field of the CMS superconducting magnet is 4 T, the magnetic length is 12.5 m and the free bore is 6 m. To reinforce the high-purity (99.998%) Al-stabilized conductor of the magnet against the magnetic loadings experienced during operation at 4.2 K, two continuous sections of Al-alloy (AA) reinforcement are Electron Beam (EB) welded to it. The reinforcements have a section of 24*18 mm and are produced in continuous 2.55 km lengths. The alloy EN AW-6082 has been selected for the reinforcement due to its excellent extrudability, high strength in the precipitation hardened states, high toughness and strength at cryogenic temperature and good EB weldability. Each of the continuous lengths of the reinforcement is extruded billet on billet and press quenched on-line from the extrusion temperature in an industrial extrusion plant. In order to insure the ready EB welda...

Learning AWS OpsWorks

CERN Document Server

Rosner, Todd

2013-01-01

A fast-paced, example-based guide to mastering AWS OpsWorks.This book is geared towards application developers, system administrators, DevOps, and anyone else interested in delivering applications while managing highly-scalable and automated infrastructures using push-button procedures. Some knowledge of what cloud computing is as well as some familiarity with Amazon Web Services is all you need as a precursor to reading this book.

Growth mechanism, distribution characteristics and reinforcing behavior of (Ti, Nb)C particle in laser cladded Fe-based composite coating

International Nuclear Information System (INIS)

Li, Qingtang; Lei, Yongping; Fu, Hanguang

2014-01-01

Highlights: • Reinforced (Ti, Nb)Cp can be synthesized in the molten pool during laser cladding. • Formation mechanism of (Ti, Nb)Cp are impacted by Ti/Nb atomic ratio. • Appropriate Ti element can improve the precipitation of carbide particle. • Excess Ti weakens this effect above-mentioned. • The wear resistance of the coating was improved when Ti/Nb = 1. - Abstract: Over the past decade, researchers have demonstrated much interest in laser cladded metal matrix composite coatings for its good wear resistance, corrosion resistance, and high temperature properties. In this paper, in-situ (Ti, Nb)C particle reinforced Fe-based composite coatings were produced by laser cladding. The effects of Ti/Nb(atomic ratio) in the cladding powder on the formation mechanism and distribution characteristics of multiple particle were investigated. The results showed that when Ti/Nb > 1, Ti had a stronger ability to bond with C compared with Nb. (Ti, Nb)C multiple particles with TiC core formed in the molten pool. With the decrease of Ti/Nb, core-shell structure disappeared, the structure of particle got close to that of NbC gradually. It is found that the amount, area ratio and distribution of the reinforced particle in the coating containing Ti and Nb elements were improved, compared with these in the coating containing equal Nb element. When Ti/Nb = 1, the effects above-mentioned is most prominent, and the wear resistance of the coating is promoted obviously

Growth mechanism, distribution characteristics and reinforcing behavior of (Ti, Nb)C particle in laser cladded Fe-based composite coating

Energy Technology Data Exchange (ETDEWEB)

Li, Qingtang, E-mail: liqingtang123@126.com; Lei, Yongping, E-mail: yplei@bjut.edu.cn; Fu, Hanguang

2014-10-15

Highlights: • Reinforced (Ti, Nb)Cp can be synthesized in the molten pool during laser cladding. • Formation mechanism of (Ti, Nb)Cp are impacted by Ti/Nb atomic ratio. • Appropriate Ti element can improve the precipitation of carbide particle. • Excess Ti weakens this effect above-mentioned. • The wear resistance of the coating was improved when Ti/Nb = 1. - Abstract: Over the past decade, researchers have demonstrated much interest in laser cladded metal matrix composite coatings for its good wear resistance, corrosion resistance, and high temperature properties. In this paper, in-situ (Ti, Nb)C particle reinforced Fe-based composite coatings were produced by laser cladding. The effects of Ti/Nb(atomic ratio) in the cladding powder on the formation mechanism and distribution characteristics of multiple particle were investigated. The results showed that when Ti/Nb > 1, Ti had a stronger ability to bond with C compared with Nb. (Ti, Nb)C multiple particles with TiC core formed in the molten pool. With the decrease of Ti/Nb, core-shell structure disappeared, the structure of particle got close to that of NbC gradually. It is found that the amount, area ratio and distribution of the reinforced particle in the coating containing Ti and Nb elements were improved, compared with these in the coating containing equal Nb element. When Ti/Nb = 1, the effects above-mentioned is most prominent, and the wear resistance of the coating is promoted obviously.

Elevated temperature wear of Al6061 and Al6061-20%Al{sub 2}O{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Singh, J.; Alpas, A.T. [Univ. of Windsor, Ontario (Canada)

1995-04-01

Both current and potential applications of particulate reinforced aluminum alloys involve components which are required to operate under sliding contact conditions at elevated temperatures. Examples include brake rotors, piston and cylinder liners in automotive engines where operating temperatures can reach 0.5--0.8 of the melting temperature of the matrix alloy. For this reason, study of the high temperature wear resistance of aluminum alloys reinforced by Al{sub 2}O{sub 3} or SiC particles is important. These studies are also of interest for the problem of die wear during hot extrusion of aluminum matrix composites and to rationalize the process of frictional welding involved in joining of the composites. Although the room temperature tribological and mechanical behaviors of aluminum matrix composites have received considerable attention, their high temperature properties have only recently started being considered. It has been shown that Al-Si-Mg (A356) alloys with or without SiC particles show a transition from mild to severe wear when a critical temperature (at about 0.4 T{sub m}, where T{sub m} is the melting temperature of aluminum) is reached as a result of frictional heating under dry sliding conditions. In this work, high temperature wear of A16061 and A16061-20%Al{sub 2}O{sub 3} was studied at temperatures between 25--500 C. The microstructural changes that occurred during wear have been delineated in order to understand the wear mechanisms that operate at high temperatures.

Interdependent effect of chemical composition and thermal history on artificial aging of AA6061

International Nuclear Information System (INIS)

Pogatscher, S.; Antrekowitsch, H.; Uggowitzer, P.J.

2012-01-01

In this study, the interdependent effect of chemical composition and thermal history on artificial aging was investigated for the aluminum alloy AA6061. Based on thermodynamic calculations, including Al, Fe, Cr, Zn, Ti, Mg, Si and Cu, model alloys exhibiting a maximum variation of the reachable solute super-saturation of elements relevant for precipitation hardening within the compositional limits of AA6061 were produced. The artificial aging behavior of these alloys at 175 °C was studied by tensile testing for two thermal histories, including very short- and long-term room temperature storage after quenching. Precipitation during artificial aging was investigated by an analysis of yield strength data. As generally expected, precipitation kinetics was found to depend strongly on the solute super-saturation in the case of very short room temperature storage. For artificial aging after long-term room temperature storage the kinetics showed almost no dependence on the chemical composition. This seems to be an exception from simple precipitation kinetics and can be explained based on the complex role of quenched-in vacancies in artificial aging of AA6061.

Pressureless infiltration of porous Al2O3 preform in molten 6061 commercial aluminium alloy

International Nuclear Information System (INIS)

Marin, J.; Olivares, L.; Moreno, C.; Ordonez, S.; Martinez, V.

2001-01-01

This paper presents an infiltration study of Al 2 O 3 samples containing, approximately, 40% of pores with 1μ average radios. These samples were totally infiltrated with Al-6061 at 1100 deg C for 24 hs in air. Microstructural analysis showed the presence of an alumina matrix infiltrated through mechanisms that combine reactive processes and capillarity, and thus being coherent with the presence of open and closed porosity. The metallographic analysis showed open porosity infiltrated with Al-6061 by capillarity, while SEM micrographs corresponding to this system also showed closed pores filled with metal, that was transported into the ceramic matrix through a reactivate infiltration mechanism. The EDAX analysis for the Al 2 O 3 /Al 6061 system showed areas rich in silicon and copper at the metal-ceramic interface, while the ceramic phase showed the presence of Mg. XRD identified the presence of the MgAl 2 O 4 spinel in the ceramic phase

Mechanical and thermal properties of bio-composites based on polypropylene reinforced with Nut-shells of Argan particles

International Nuclear Information System (INIS)

Essabir, H.; Hilali, E.; Elgharad, A.; El Minor, H.; Imad, A.; Elamraoui, A.; Al Gaoudi, O.

2013-01-01

Highlights: ► Nuts-shells of Argan particles are used as reinforcement in thermoplastic matrix. ► Particles are homogeneously dispersed and distributed within PP matrix. ► Mechanical and thermal characterization of the composite are applied. ► Particles–matrix adhesion was assured by the use of a SBS compatibilizer. - Abstract: This study treats the combined effects of both particle sizes and particle loading on the mechanical and thermal properties of polypropylene (PP) composites reinforced with Nut-shells of Argan (NA) particles. Three range sizes of particles were used in the presence of a polypropylene matrix grafted with 8 wt.% of a linear block copolymer based on styrene and butadiene coupling agent, to improve adhesion between the particles and the matrix. The composites were prepared through melt-blending using an internal mixer and the tensile specimens were prepared using a hot press molding machine. Scanning Electron Microscopy (SEM), Fourier Transform Infrared Spectroscopy (FT-IR), Thermo Gravimetric Analysis (TGA), Differential Thermal Analysis (DTA) and tensile tests were employed to characterize the composites at 10, 15, 20 and 25 wt.% particle contents. Results show a clear improvement in Young’s modulus from the use of particles when compared to the neat PP, a gain of 42.65%, 26.7% and 2.9% at 20 wt.% particle loading, for particle range 1, 2 and 3, respectively. In addition a notable increase in the Young’s modulus was observed when decrease the particle size. The thermal stability of composites exhibits a slight decrease (256–230 °C) with particles loading from 10 to 25 wt.%, against neat PP (258 °C)

Correlations Between Arrangement of Reinforcing Particles and Mechanical Properties in Pressure Die Cast AlSi11-SiC Composites

Directory of Open Access Journals (Sweden)

Konopka Z.

2014-06-01

Full Text Available The work presents the investigation results concerning the structure of composite pressure die castings with AlSi11 alloy matrix reinforced with SiC particles. Examination has been held for composites containing 10 and 20 volume percent of SiC particles. The arrangement of the reinforcing particles within the matrix has been qualitatively assessed in specimens cut out of the castings. The index of distribution was determined on the basis of particle count in elementary measuring fields. The tensile strength, the yield point and elongation of the obtained composite were measured. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. The regression equation describing the change of the considered arrangement particles index and mechanical properties were found as a function of the pressure die casting parameters. The infuence of particle arrangement in composite matrix on mechanical properties these material was examined and the functions of correlations between values were obtained. The conclusion gives the analysis and the interpretation of the obtained results.

Remembrance of professor Tadeusz Marciniak - Lviv tradition in Wrocław.

Science.gov (United States)

Kacała, Ryszard R; Woźniak, Sławomir; Porwolik, Michał; Dąbrowski, Paweł; Domagała, Zygmunt; Kacała, Arkadiusz; Gworys, Bohdan

2015-01-01

After the seizure of Lviv by the Soviets, in the years 1944-1946, Tadeusz Marciniak worked in the Descriptive Anatomy Department in the State-Medical Institute of Lviv and also performed the function of the dean of the Medical Faculty. On receiving a proposal to assume the Chair of the Anatomy Department in Wrocław, he made the decision to leave Lviv. By July 2nd, 1946, prof. Tadeusz Marciniak had taken over the duties of full professor of the Descriptive Anatomy Department of the Medical Faculty of the University and the Technical College of Wrocław. On taking his job in Wrocław, prof. Marciniak undertook attempts to restore the worn out parts of the Anatomy Department building. Due to the lack of Polish manuals, he also took to the preparation of scripts for medical students. Professor Marciniak was a member of the Wrocław Section of the Polish Anthropological Association and a regular member of the Wroclaw Association of Science. His main scientific interests referred to the morphogenesis of the central nervous system and urinary system. He concentrated on circulatory system and muscular system tetralogies. Professor Marciniak also actively participated in administrative work at the university. In the years 1947-1948, he held the office of associate dean of the Medical Faculty, and till 1950 was a member of the Senate of the University and Technical College of Wrocław. In the years 1959-1962, he was a vice rector of the Medical University of Wrocław.

Thermo-mechanical characterization of siliconized E-glass fiber/hematite particles reinforced epoxy resin hybrid composite

Energy Technology Data Exchange (ETDEWEB)

Arun Prakash, V.R., E-mail: vinprakash101@gmail.com; Rajadurai, A., E-mail: rajadurai@annauniv.edu.in

2016-10-30

Highlights: • Particles dimension have reduced using Ball milling process. • Importance of surface modification was explored. • Surface modification has been done to improve adhesion of fiber/particles with epoxy. • Mechanical properties has been increased by adding modified fiber and particles. • Thermal properties have been increased. - Abstract: In this present work hybrid polymer (epoxy) matrix composite has been strengthened with surface modified E-glass fiber and iron(III) oxide particles with varying size. The particle sizes of 200 nm and <100 nm has been prepared by high energy ball milling and sol-gel methods respectively. To enhance better dispersion of particles and improve adhesion of fibers and fillers with epoxy matrix surface modification process has been done on both fiber and filler by an amino functional silane 3-Aminopropyltrimethoxysilane (APTMS). Crystalline and functional groups of siliconized iron(III) oxide particles were characterized by XRD and FTIR spectroscopy analysis. Fixed quantity of surface treated 15 vol% E-glass fiber was laid along with 0.5 and 1.0 vol% of iron(III) oxide particles into the matrix to fabricate hybrid composites. The composites were cured by an aliphatic hardener Triethylenetetramine (TETA). Effectiveness of surface modified particles and fibers addition into the resin matrix were revealed by mechanical testing like tensile testing, flexural testing, impact testing, inter laminar shear strength and hardness. Thermal behavior of composites was evaluated by TGA, DSC and thermal conductivity (Lee’s disc). The scanning electron microscopy was employed to found shape and size of iron(III) oxide particles adhesion quality of fiber with epoxy matrix. Good dispersion of fillers in matrix was achieved with surface modifier APTMS. Tensile, flexural, impact and inter laminar shear strength of composites was improved by reinforcing surface modified fiber and filler. Thermal stability of epoxy resin was improved

Estudio mediante tres técnicas del módulo elástico de un material compuesto de Al(6061 con un alto contenido (40%vol de SiC

Directory of Open Access Journals (Sweden)

Fernández, R.

2001-04-01

Full Text Available The purpose of this investigation is to study the elastic behavior of a discontinuously reinforced composite material, Al(6061-40vol%SiC, by using three different procedures: Extensometry in uniaxial testing, pendulum elasticimeter, and propagation of acoustic signals in the material. The high ceramic content of this material provides it with a high stiffness without a significant increase in density. Because of this, the material is suitable as structural component in the automotive and aerospace industry.

El objetivo de esta investigación es estudiar el comportamiento elástico de un material compuesto con refuerzo discontinuo, Al(6061-40vol%SiC, mediante tres técnicas diferentes: extensometría para ensayos uniaxiales convencionales, elasticímetro pendular y mediante medidas de la velocidad de propagación de señales acústicas en el material. El alto contenido de la fase cerámica en este material le confiere elevada rigidez sin que su densidad aumente significativamente por lo que lo hacen adecuado como material estructural en diversas aplicaciones en el sector del transporte (automoción, aerospacial.

Effect of silica particles modified by in-situ and ex-situ methods on the reinforcement of silicone rubber

International Nuclear Information System (INIS)

Song, Yingze; Yu, Jinhong; Dai, Dan; Song, Lixian; Jiang, Nan

2014-01-01

Highlights: • In-situ and ex-situ methods were applied to modify silica particles. • In-situ method was more beneficial to preparing silica particles with high BET surface area. • Silicone rubber filled with in-situ modified silica exhibits excellent mechanical and thermal properties. - Abstract: In-situ and ex-situ methods were applied to modify silica particles in order to investigate their effects on the reinforcement of silicone rubber. Surface area and pore analyzer, laser particle size analyzer, Fourier-transform infrared spectroscopy (FTIR), contact-angle instrument, and transmission electron microscope (TEM) were utilized to investigate the structure and properties of the modified silica particles. Dynamic mechanical thermal analyzer (DMTA) was employed to characterize the vulcanizing behavior and mechanical properties of the composites. Thermogravimetric analysis (TGA) was performed to test the thermal stability of the composites. FTIR and contact angle analysis indicated that silica particles were successfully modified by these two methods. The BET surface area and TEM results reflected that in-situ modification was more beneficial to preparing silica particles with irregular shape and higher BET surface area in comparison with ex-situ modification. The DMTA and TGA data revealed that compared with ex-situ modification, the in-situ modification produced positive influence on the reinforcement of silicone rubber

Tank 241-AW-101 tank characterization plan

International Nuclear Information System (INIS)

Sathyanarayana, P.

1994-01-01

The first section gives a summary of the available information for Tank AW-101. Included in the discussion are the process history and recent sampling events for the tank, as well as general information about the tank such as its age and the risers to be used for sampling. Tank 241-AW-101 is one of the 25 tanks on the Flammable Gas Watch List. To resolve the Flammable Gas safety issue, characterization of the tanks, including intrusive tank sampling, must be performed. Prior to sampling, however, the potential for the following scenarios must be evaluated: the potential for ignition of flammable gases such as hydrogen-air and/or hydrogen-nitrous oxide; and the potential for secondary ignition of organic-nitrate/nitrate mixtures in crust layer initiated by the burning of flammable gases or by a mechanical in-tank energy source. The characterization effort applicable to this Tank Characterization Plan is focused on the resolution of the crust burn flammable gas safety issue of Tank AW-101. To evaluate the potential for a crust burn of the waste material, calorimetry tests will be performed on the waste. Differential Scanning Calorimetry (DSC) will be used to determine whether an exothermic reaction exists

Microstructure and wear properties of the electroslag remelting layer reinforced by TiC particles

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

The electroslag remelting (ESR) layer reinforced by TiC particles was obtained by electroslag remelting.The microstructure and wear properties of the ESR layer were studied by means of scanning electron microscopy (SEM),X-ray diffraction (XRD),and wear test.The results indicate that TiC particles are synthesized by self-propagating high-temperature synthesis (SHS) reaction during the electroslag remelting process.The size of TiC particles is in the range of 1-10 μm,and the distribution of TiC particles is uniform,from outside to inside of the ESR layer,and the volume fraction and the size of TiC particles decrease gradually.Molten iron and slag flow into porosity due to the SHS process leading to rapid densification and the elimination of porosity in the ESR layer during the ESR process.TiC particles enhance the wear resistance of the ESR layer,whereas CaF2 can improve the high temperature lubricating property of the ESR layer.

Microstructural development from interdiffusion and reaction between U−Mo and AA6061 alloys annealed at 600° and 550 °C

Energy Technology Data Exchange (ETDEWEB)

Perez, E., E-mail: Emmanuel.Perez@inl.gov [Nuclear Fuels and Materials Division, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States); Keiser, D.D., E-mail: dennis.keiser@inl.gov [Nuclear Fuels and Materials Division, Idaho National Laboratory, P.O. Box 1625, Idaho Falls, ID 83415-6188 (United States); Sohn, Y.H., E-mail: yongho.sohn@ucf.edu [Department of Materials Science and Engineering, University of Central Florida, 4000 Central Florida Blvd., Orlando, FL 32816 (United States)

2016-08-15

The U.S. Material Management and Minimization Reactor Conversion Program is developing low enrichment fuel systems encased in Al-alloy for use in research and test reactors. Monolithic fuel plates have local regions where the U−Mo fuel plate may come into contact with the Al-alloy 6061 (AA6061) cladding. This results in the development of interdiffusion zones with complex microstructures with multiple phases. In this study, the microstructural development of diffusion couples, U−7 wt%Mo, U−10 wt%Mo, and U−12 wt%Mo vs. AA6061, annealed at 600 °C for 24 h and at 550 °C for 1, 5, and 20 h, were analyzed by scanning electron microscopy with x-ray energy dispersive spectroscopy. The microstructural development and kinetics were compared to diffusion couples U−Mo vs. high purity Al and binary Al−Si alloys. The diffusion couples developed complex interaction regions where phase development was influenced by the alloying additions of the AA6061. - Highlights: • Diffusion couples of U−7Mo, U−10Mo, and U−12Mo vs. AA6061 were analyzed by SEM with XEDS. • The couples were annealed at 600 °C for 24 h and at 550 °C for 1, 5 and 20 h. • The interaction regions were more complex than those in diffusion couples of U−Mo vs. high purity Al and Al−Si alloys. • Analysis showed that the alloying additions of the AA6061 were present in the interaction regions. • Phase development was significantly influenced by the alloying additions of the AA6061.

Microstructures and properties of ceramic particle-reinforced metal matrix composite layers produced by laser cladding

Science.gov (United States)

Zhang, Qingmao; He, Jingjiang; Liu, Wenjin; Zhong, Minlin

2005-01-01

Different weight ratio of titanium, zirconium, WC and Fe-based alloy powders were mixed, and cladded onto a medium carbon steel substrate using a 3kW continuous wave CO2 laser, aiming at producing Ceramic particles- reinforced metal matrix composites (MMCs) layers. The microstructures of the layers are typical hypoeutectic, and the major phases are Ni3Si2, TiSi2, Fe3C, FeNi, MC, Fe7Mo3, Fe3B, γ(residual austenite) and M(martensite). The microstructure morphologies of MMCs layers are dendrites/cells. The MC-type reinforcements are in situ synthesis Carbides which main compositions consist of transition elements Zr, Ti, W. The MC-type particles distributed within dendrite and interdendritic regions with different volume fractions for single and overlapping clad layers. The MMCs layers are dense and free of cracks with a good metallurgical bonding between the layer and substrate. The addition ratio of WC in the mixtures has the remarkable effect on the microhardness of clad layers.

Environmental Particle Emissions due to Automated Drilling of Polypropylene Composites and Nanocomposites Reinforced with Talc, Montmorillonite and Wollastonite

Science.gov (United States)

Starost, K.; Frijns, E.; Laer, J. V.; Faisal, N.; Egizabal, A.; Elizextea, C.; Nelissen, I.; Blazquez, M.; Njuguna, J.

2017-05-01

In this study, the effect on nanoparticle emissions due to drilling on Polypropylene (PP) reinforced with 20% talc, 5% montmorillonite (MMT) and 5% Wollastonite (WO) is investigated. The study is the first to explore the nanoparticle release from WO and talc reinforced composites and compares the results to previously researched MMT. With 5% WO, equivalent tensile properties with a 10 % weight reduction were obtained relative to the reference 20% talc sample. The materials were fabricated through injection moulding. The nanorelease studies were undertaken using the controlled drilling methodology for nanoparticle exposure assessment developed within the European Commission funded SIRENA Life 11 ENV/ES/506 project. Measurements were taken using CPC and DMS50 equipment for real-time characterization and measurements. The particle number concentration (of particles <1000nm) and particle size distribution (4.87nm - 562.34nm) of the particles emitted during drilling were evaluated to investigate the effect of the silicate fillers on the particles released. The nano-filled samples exhibited a 33% decrease (MMT sample) or a 30% increase (WO sample) on the average particle number concentration released in comparison to the neat polypropylene sample. The size distribution data displayed a substantial percentage of the particles released from the PP, PP/WO and PP/MMT samples to be between 5-20nm, whereas the PP/talc sample emitted larger particle diameters.

Particle-Based Geometric and Mechanical Modelling of Woven Technical Textiles and Reinforcements for Composites

Science.gov (United States)

Samadi, Reza

affecting the textile geometry and constitutive behaviour under evolving loading; 5) validating simulation results with experimental trials; and 6) demonstrating the applicability of the simulation procedure to textile reinforcements featuring large numbers of small fibres as used in PMCs. As a starting point, the effects of reinforcement configuration on the in-plane permeability of textile reinforcements, through-thickness thermal conductivity of PMCs and in-plane stiffness of unidirectional and bidirectional PMCs were quantified systematically and correlated with specific geometric parameters. Variability was quantified for each property at a constant fibre volume fraction. It was observed that variability differed strongly between properties; as such, the simulated behaviour can be related to variability levels seen in experimental measurements. The effects of the geometry of textile reinforcements on the aforementioned processing and performance properties of the textiles and PMCs made from these textiles was demonstrated and validated, but only for simple cases as thorough and credible geometric models were not available at the onset of this work. Outcomes of this work were published in a peer-reviewed journal [101]. Through this thesis it was demonstrated that predicting changes in textile geometry prior and during loading is feasible using the proposed particle-based modelling method. The particle-based modelling method relies on discrete mechanics and offers an alternative to more traditional methods based on continuum mechanics. Specifically it alleviates issues caused by large strains and management of intricate, evolving contact present in finite element simulations. The particle-based modelling method enables credible, intricate modelling of the geometry of textiles at the mesoscopic scale as well as faithful mechanical modelling under load. Changes to textile geometry and configuration due to the normal compaction pressure, stress relaxation, in-plane shear

Wear behaviour of A356 aluminium alloy reinforced with micron and nano size SiC particles

CSIR Research Space (South Africa)

Camagu, ST

2013-07-01

Full Text Available A method for producing metal matrix composites MMC was successfully implemented for mixing nano and low micron (“Hybrid”) sized SiC reinforcing particles in an aluminium alloy matrix. Due to the improved specific modulus and strength, MMC...

Effect of reinforcing particle type on morphology and age-hardening behavior of Al–4.5 wt.% Cu based nanocomposites synthesized through mechanical milling

Energy Technology Data Exchange (ETDEWEB)

Mostaed, A., E-mail: alimostaed@yahoo.com [Advanced Materials and Nanotechnology Research Center, Faculty of Mechanical Engineering, K.N. Toosi University of Technology, 16765-3381 Pardis Street, Tehran (Iran, Islamic Republic of); Saghafian, H.; Mostaed, E. [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, 16846-13114 Narmak, Tehran (Iran, Islamic Republic of); Shokuhfar, A. [Advanced Materials and Nanotechnology Research Center, Faculty of Mechanical Engineering, K.N. Toosi University of Technology, 16765-3381 Pardis Street, Tehran (Iran, Islamic Republic of); Rezaie, H.R. [School of Metallurgy and Materials Engineering, Iran University of Science and Technology, 16846-13114 Narmak, Tehran (Iran, Islamic Republic of)

2013-02-15

The effects of reinforcing particle type (SiC and TiC) on morphology and precipitation hardening behavior of Al–4.5%Cu based nanocomposites synthesized via mechanical milling were investigated in the current work. In order to study the microstructure and morphology of mechanically milled powder, X-ray diffraction technique, scanning electron microscopy and high resolution transmission electron microscopy were utilized. Results revealed that at the early stages of mechanical milling, when reinforcing particles are polycrystal, the alloying process is enhanced more in the case of using the TiC particles as reinforcement. But, at the final stages of mechanical milling, when reinforcing particles are single crystal, the alloying process is enhanced more in the case of using the SiC ones. Transmission electron microscopy results demonstrated that Al–4.5 wt.%Cu based nanocomposite powders were synthesized and confirmed that the mutual diffusion of aluminum and copper occurs through the interfacial plane of (200). The hardness results showed that not only does introducing 4 vol.% of reinforcing particles (SiC or TiC) considerably decrease the porosity of the bulk composite samples, but also it approximately doubles the hardness of Al–4.5 wt.%Cu alloy (53.4 HB). Finally, apart from TEM and scanning electron microscopy observation which are localized, a decline in hardness in the TiC and SiC contained samples, respectively, after 1.5 and 2 h aging time at 473 K proves the fact that the size of SiC particles is smaller than the size of the TiC ones. - Highlights: ► HRTEM results show mutual diffusion of Al and Cu occurs through the (200) planes. ► TiC particles enhance alloying process more than the SiC ones at the early stages of MM. ► SiC particles enhance alloying process more than the TiC ones at the final stages of MM.

Effect of reinforcing particle type on morphology and age-hardening behavior of Al–4.5 wt.% Cu based nanocomposites synthesized through mechanical milling

International Nuclear Information System (INIS)

Mostaed, A.; Saghafian, H.; Mostaed, E.; Shokuhfar, A.; Rezaie, H.R.

2013-01-01

The effects of reinforcing particle type (SiC and TiC) on morphology and precipitation hardening behavior of Al–4.5%Cu based nanocomposites synthesized via mechanical milling were investigated in the current work. In order to study the microstructure and morphology of mechanically milled powder, X-ray diffraction technique, scanning electron microscopy and high resolution transmission electron microscopy were utilized. Results revealed that at the early stages of mechanical milling, when reinforcing particles are polycrystal, the alloying process is enhanced more in the case of using the TiC particles as reinforcement. But, at the final stages of mechanical milling, when reinforcing particles are single crystal, the alloying process is enhanced more in the case of using the SiC ones. Transmission electron microscopy results demonstrated that Al–4.5 wt.%Cu based nanocomposite powders were synthesized and confirmed that the mutual diffusion of aluminum and copper occurs through the interfacial plane of (200). The hardness results showed that not only does introducing 4 vol.% of reinforcing particles (SiC or TiC) considerably decrease the porosity of the bulk composite samples, but also it approximately doubles the hardness of Al–4.5 wt.%Cu alloy (53.4 HB). Finally, apart from TEM and scanning electron microscopy observation which are localized, a decline in hardness in the TiC and SiC contained samples, respectively, after 1.5 and 2 h aging time at 473 K proves the fact that the size of SiC particles is smaller than the size of the TiC ones. - Highlights: ► HRTEM results show mutual diffusion of Al and Cu occurs through the (200) planes. ► TiC particles enhance alloying process more than the SiC ones at the early stages of MM. ► SiC particles enhance alloying process more than the TiC ones at the final stages of MM

Tensile behavior of friction stir welded AA 6061-T4 aluminum alloy joints

International Nuclear Information System (INIS)

Heidarzadeh, A.; Khodaverdizadeh, H.; Mahmoudi, A.; Nazari, E.

2012-01-01

Highlights: ► Range of parameters for defect-free friction stir welded AA 6061-T4 was reached. ► A model was developed for predicting UTS and EL of friction stir welded AA 6061-T4. ► The maximum values of UTS and EL of joints were estimated by developed model. ► The optimum values of FSW process parameters were determined. -- Abstract: In this investigation response surface methodology based on a central composite rotatable design with three parameters, five levels and 20 runs, was used to develop a mathematical model predicting the tensile properties of friction stir welded AA 6061-T4 aluminum alloy joints at 95% confidence level. The three welding parameters considered were tool rotational speed, welding speed and axial force. Analysis of variance was applied to validate the predicted model. Microstructural characterization and fractography of joints were examined using optical and scanning electron microscopes. Also, the effects of the welding parameters on tensile properties of friction stir welded joints were analyzed in detail. The results showed that the optimum parameters to get a maximum of tensile strength were 920 rev/min, 78 mm/min and 7.2 kN, where the maximum of tensile elongation was obtained at 1300 rev/min, 60 mm/min and 8 kN.

Laser cladding of Inconel 625-based composite coatings reinforced by porous chromium carbide particles

Science.gov (United States)

Janicki, Damian

2017-09-01

Inconel 625/Cr3C2 composite coatings were produced via a laser cladding process using Cr3C2 reinforcing particles presenting an open porosity of about 60%. A laser cladding system used consisted of a direct diode laser with a rectangular beam spot and the top-hat beam profile, and an off-axis powder injection nozzle. The microstructural characteristics of the coatings was investigated with the use of scanning electron microscopy and X-ray diffraction. A complete infiltration of the porous structure of Cr3C2 reinforcing particles and low degree of their dissolution have been achieved in a very narrow range of processing parameters. Crack-free composite coatings having a uniform distribution of the Cr3C2 particles and their fraction up to 36 vol% were produced. Comparative erosion tests between the Inconel 625/Cr3C2 composite coatings and the metallic Inconel 625 coatings were performed following the ASTM G 76 standard test method. It was found that the composite coatings have a significantly higher erosion resistance to that of metallic coatings for both 30° and 90° impingement angles. Additionally, the erosion performances of composite coatings were similar for both the normal and oblique impact conditions. The erosive wear behaviour of composite coatings is discussed and related to the unique microstructure of these coatings.

The mechanical properties of magnesium matrix composites reinforced with 10 wt.% W14Al86 alloy particles

International Nuclear Information System (INIS)

Tang, H.G.; Ma, X.F.; Zhao, W.; Cai, S.G.; Zhao, B.; Qiao, Z.H.

2007-01-01

The Mg-based metal matrix composite reinforced by 10 wt.% W 14 Al 86 alloy particles has been prepared by mechanical alloying and press-forming process. X-ray diffraction studies confirm the formation of the composite. Microstructure characterization of the samples reveals the uniform distribution of fine W 14 Al 86 alloy. Mechanical properties characterization revealed that the reinforcement of W 14 Al 86 alloy lead to a significant increase in hardness and tensile strength of Mg and AZ91

Particle energization by inertial Alfven wave in auroral ionosphere

Science.gov (United States)

Kumar, S.

2017-12-01

The role of inertial Alfven wave in auroral acceleration region and in the inertial regime to energize the plasma particles is an interesting field and widely discussed observationally as well as theoretically in recent years. In this work, we present the density perturbations by inertial Alfvén wave (AW) in the auroral ionosphere. We obtain dynamical equations for inertial AW and fast mode of AW using two-fluid model and then solve them numerically in order to analyze the localized structures and cavity formation. The ponderomotive force due to the high frequency inertial AW changes the background density and is believed to be responsible for the wave localization or for the formation of density cavities in auroral ionosphere. These density cavities are believed to be the sites for particle energization. This perturbed density channel grow with time until the modulation instability acquires steady state. We find that the density cavities are accompanied by the high amplitude magnetic fields. The amplitude of the strongest density cavity is estimated as ˜ 0.26n0 (n0 is unperturbed plasma number density). The results presented here are found consistent with the observational studies using FAST spacecraft.

Prevention of non-ductile fracture in 6061-T6 aluminum nuclear pressure vessels

International Nuclear Information System (INIS)

Yahr, G.T.

1995-01-01

The American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel Committee has approved rules for the use of 6061-T6 and 6061-T651 aluminum for the construction of Class 1 welded nuclear pressure vessels for temperatures not exceeding 149 C (300 F). Nuclear Code Case N-519 allows the use of this aluminum in the construction of low temperature research reactors such as the Advanced Neutron Source. The rules for protection against non-ductile fracture are discussed. The basis for a value of 25.3 MPa √m (23 ksi √in.) for the critical or reference stress intensity factor for use in the fracture analysis is presented. Requirements for consideration of the effects of neutron irradiation on the fracture toughness are discussed

Optimization of Reinforced Concrete Reservoir with Circumferential Stiffeners Strips by Particle Swarm Algorithm

Directory of Open Access Journals (Sweden)

GholamReza Havaei

2015-09-01

Full Text Available Reinforced concrete reservoirs (RCR have been used extensively in municipal and industrial facilities for several decades. The design of these structures requires that attention be given not only to strength requirements, but to serviceability requirements as well. These types of structures will be square, round, and oval reinforced concrete structures which may be above, below, or partially below ground. The main challenge is to design concrete liquid containing structures which will resist the extremes of seasonal temperature changes, a variety of loading conditions, and remain liquid tight for useful life of 50 to 60 years. In this study, optimization is performed by particle swarm algorithm basd on structural design. Firstly by structural analysis all range of shell thickness and areas of rebar find. In the second step by parameter identification system interchange algorithm, source code which developed in particle swarm algorithm by MATLAB software linked to analysis software. Therefore best and optimized thicknesses and total area of bars for each element find. Lastly with circumferential stiffeners structure optimize and show 19% decrease in weight of rebar, 20% decrease in volume of concrete, and 13% minimum cost reduction in construction procedure compared with conventional 10,000 m3 RCR structures.

A statistical analysis on erosion wear behaviour of A356 alloy reinforced with in situ formed TiB2 particles

International Nuclear Information System (INIS)

Kumar, S.; Subramanya Sarma, V.; Murty, B.S.

2008-01-01

Solid particle erosion wear behaviour of A356 and A356/TiB 2 in situ composites has been studied. A356 alloy reinforced with in situ TiB 2 particles was fabricated by the reaction of halide salts with aluminium melt and the formation of Al 3 Ti brittle phase is completely suppressed. The composites show good grain refinement of α-Al and modification of eutectic Si. These in situ composites show high hardness and better erosion resistance than the base alloy. Though the sizes of in situ formed TiB 2 reinforcement particles are smaller than the erodent SiC particles, TiB 2 particles are able to effectively resist the erodent particles. Design of experiment has been used to run the solid particle erosion experiment. An attempt has also been made to develop a mathematical model by using regression analysis. Analysis of variance (ANOVA) technique is applied to check the validity of the developed model. Student's t-test is utilized to find out the significance of factors. The wear mechanism has been studied by analyzing the surface of the worn specimen using scanning electron microscopy and energy dispersive X-ray microanalysis

Test plan for Tank 241-AW-101 solubility screening tests

International Nuclear Information System (INIS)

Person, J.C.

1998-01-01

Tank 241-AW-101 (101-AW) has been identified as one of the early tanks to be for retrieved for low level waste pretreatment and immobilization and retrieval of the tank waste may require dilution. This test is to determine the effects of dilution on the mass of solids and their composition. This test plan gives test instructions, example data sheets, a waste compatibility review, and a waste stream fact sheet. This test Plan is similar to tests on tanks 241-AN-102 (Person 1998a) and 241-AN-107 (Person 1998 b). The 101-AW tests will be done with composites of liquid and solids from grab samples that were taken in 1998 (Benar 1998). Future revisions of the Tank Sampling and Analysis Plan (Benar 1998) may change the details of the work performed under this test plan

Investigations on the Hot Stamping of AW-7921-T4 Alloy Sheet

Directory of Open Access Journals (Sweden)

M. Kumar

2017-01-01

Full Text Available AW-7xxx alloys have been nowadays considered for greater light weighting potential in automotive industry due to its higher strength compared to AW-5xxx and AW-6xxx alloys. However, due to their lower formability the forming processes are still in development. This paper investigates one such forming process called hot stamping. The investigation started by carrying out hot tensile testing of an AW-7xxx alloy, that is, AW-7921 at temperatures between 350°C and 475°C, to measure the strength and formability. Formability was found to improve with increasing temperature and was sensitive to the strain rate. Dynamic recovery is considered as usual reason for the formability improvement. However, examining the precipitation states of the as-received condition and after hot stamping using differential scanning calorimetry (DSC, the dissolution of precipitates was also believed to contribute to this increase in formability. Following solution heat treatment there was no precipitation during cooling across the cooling rates investigated (5–10°C/s. Samples taken from parts hot stamped at 10 and 20 mm s−1 had similar yield strengths. A 3-step paint baking heat treatment yielded a higher postpaint baking strength than a single step treatment.

X-ray microtomography of damage in particle-reinforced metal matrix composites

International Nuclear Information System (INIS)

Mummery, P.M.; Derby, B.; Anderson, P.; Davis, G.; Elliott, J.C.

1993-01-01

The damage which occurs on plastic straining of silicon carbide particle-reinforced aluminium alloys has been characterised using x-ray microtomography. The technique is used to provide density measurements as a function of strain in addition to imaging the internal structure with a resolution of ∼15μm. This allows a much more accurate determination of microstructural damage in terms of void growth than is available from measurements of density using buoyancy methods or from elastic modulus decrease. These data can be combined with acoustic emission measurements during straining to allow damage nucleation and growth contributions to be separated. (orig.)

Long-term changes in amphetamine-induced reinforcement and aversion in rats following exposure to 56Fe particle

Science.gov (United States)

Rabin, B. M.; Joseph, J. A.; Shukitt-Hale, B.

Exposing rats to heavy particles produces alterations in the functioning of dopaminergic neurons and in the behaviors that depend upon the integrity of the dopaminergic system. Two of these dopamine-dependent behaviors include amphetamine-induced reinforcement, measure using the conditioned place preference procedure, and amphetamine-induced reinforcement, measured using the conditioned place preference procedure, and amphetamine-induced aversion, measured using the conditioned taste aversion. Previous research has shown that exposing rats to 1.0 Gy of 1GeV/n 56Fe particles produced a disruption of an amphetamine-induced taste aversion 3 days following exposure, but produced an apparent enhancement of the aversion 112 days following exposure. The present experiments were designed to provide a further evaluation of these results by examining taste aversion learning 154 days following exposure to 1.0Gy 56Fe particles and to establish the convergent validity of the taste aversion results by looking at the effects of exposure on the establishment of an amphetamine-induced conditioned place preference 3, 7, and 16 weeks following irradiation. The taste aversion results failed to confirm the apparent enhancement of the amphetamine-induced CTA observed in the prior experiment. However, exposure to 56Fe particles prevented the acquisition of amphetamine-induced place preference at all three-time intervals. The results are interpreted as indicating that exposure to heavy particles can produce long-term changes in behavioral functioning.

Performance Optimization of Electrical Discharge Machining (Die Sinker for Al-6061 via Taguchi Approach

Directory of Open Access Journals (Sweden)

Muhammad Qaiser Saleem

2015-04-01

Full Text Available This paper parametrically optimizes the EDM (Electrical Discharge Machining process in die sinking mode for material removal rate, surface roughness and edge quality of aluminum alloy Al-6061. The effect of eight parameters namely discharge current, pulse on-time, pulse off-time, auxiliary current, working time, jump time distance, servo speed and work piece hardness are investigated. Taguchi's orthogonal array L18 is employed herein for experimentation. ANOVA (Analysis of Variance with F-ratio criterion at 95% confidence level is used for identification of significant parameters whereas SNR (Signal to Noise Ratio is used for determination of optimum levels. Optimization obtained for Al-6061 with parametric combination investigated herein is validated by the confirmation run.

Laser cladding in-situ carbide particle reinforced Fe-based composite coatings with rare earth oxide addition

Institute of Scientific and Technical Information of China (English)

吴朝锋; 马明星; 刘文今; 钟敏霖; 张红军; 张伟明

2009-01-01

Particulate reinforced metal matrix composite(PR-MMC) has excellent properties such as good wear resistance,corrosion resistance and high temperature properties.Laser cladding is usually used to form PR-MMC on metal surface with various volume fractions of ceramic particles.Recent literatures showed that laser melting of powder mixture containing carbon and carbide-forming elements,was favorable for the formation of in-situ synthesized carbide particles.In this paper,rare earth oxide(RE2O3) was added into t...

Adiabatic shear localization in ultrafine grained 6061 aluminum alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Bingfeng, E-mail: biw009@ucsd.edu [School of Materials Science and Engineering, Central South University, Changsha 410083 (China); Department of Mechanical and Aerospace Engineering, University of California, San Diego (United States); State Key Laboratory for Powder Metallurgy, Central South University, Changsha, Hunan (China); Key Lab of Nonferrous Materials, Ministry of Education, Central South University, Changsha 410083 (China); Ma, Rui; Zhou, Jindian [School of Materials Science and Engineering, Central South University, Changsha 410083 (China); Li, Zezhou; Zhao, Shiteng [Department of Mechanical and Aerospace Engineering, University of California, San Diego (United States); Huang, Xiaoxia [School of Materials Science and Engineering, Central South University, Changsha 410083 (China)

2016-10-15

Localized shear is an important mode of deformation; it leads to catastrophic failure with low ductility, and occurs frequently during high strain-rate deformation. The hat-shaped specimen has been successfully used to generate shear bands under controlled shock-loading tests. The microstructure in the forced shear band was characterized by optical microscopy, microhardness, and transmission electron microscopy. The true flow stress in the shear region can reach 800 MPa where the strain is about 2.2. The whole shear localization process lasts for about 100 μs. The shear band is a long and straight band distinguished from the matrix by boundaries. It can be seen that the grains in the boundary of the shear band are highly elongated along the shear direction and form the elongated cell structures (0.2 µm in width), and the core of the shear band consists of a number of recrystallized equiaxed grains with 0.2−0.3 µm in diameters, and the second phase particles distribute in the boundary of the ultrafine equiaxed new grains. The calculated temperature in the shear band can reach about 667 K. Finally, the formation of the shear band in the ultrafine grained 6061 aluminum alloy and its microstructural evolution are proposed.

Study on preparation and properties of molybdenum alloys reinforced by nano-sized ZrO2 particles

International Nuclear Information System (INIS)

Cui, Chaopeng; Gao, Yimin; Zhou, Yucheng; Wei, Shizhong; Zhang, Guoshang; Zhu, Xiangwei; Guo, Songliang

2016-01-01

The nano-sized ZrO 2 -reinforced Mo alloy was prepared by a hydrothermal method and a subsequent powder metallurgy process. During the hydrothermal process, the nano-sized ZrO 2 particles were added into the Mo powder via the hydrothermal synthesis. The grain size of Mo powder decreases obviously with the addition of ZrO 2 particles, and the fine-grain sintered structure is obtained correspondingly due to hereditation. In addition to a few of nano-sized ZrO 2 particles in grain boundaries or sub-boundaries, most are dispersed in grains. The tensile strength and yield strength have been increased by 32.33 and 53.76 %. (orig.)

Solid Particle Erosion of Date Palm Leaf Fiber Reinforced Polyvinyl Alcohol Composites

Directory of Open Access Journals (Sweden)

Jyoti R. Mohanty

2014-01-01

Full Text Available Solid particle erosion behavior of short date palm leaf (DPL fiber reinforced polyvinyl alcohol (PVA composite has been studied using silica sand particles (200 ± 50 μm as an erodent at different impingement angles (15–90° and impact velocities (48–109 m/s. The influence of fiber content (wt% of DPL fiber on erosion rate of PVA/DPL composite has also been investigated. The neat PVA shows maximum erosion rate at 30° impingement angle whereas PVA/DPL composites exhibit maximum erosion rate at 45° impingement angle irrespective of fiber loading showing semiductile behavior. The erosion efficiency of PVA and its composites varies from 0.735 to 16.289% for different impact velocities studied. The eroded surfaces were observed under scanning electron microscope (SEM to understand the erosion mechanism.

Magnesium alloy AZ63A reinforcement by alloying with gallium and using high-disperse ZrO2 particles

Directory of Open Access Journals (Sweden)

J. Khokhlova

2016-12-01

Full Text Available The aim of this work was to obtain an experimental magnesium alloy by remelting standard AZ63A alloy with addition of gallium ligatures and ZrO2 particles. This allowed reinforcement of alloy and increase its hardness and Young's modulus. The chemical analysis of this alloy shows two types of structures which are evenly distributed in volume. Thus we can conclude that reinforcing effect is the result of formation of intermetallic phase Mg5-Ga2.

Fabrication of Unidirectional Fiber Reinforced 6061 Aluminum Alloy Using High Pressure Squeeze Casting

Science.gov (United States)

1988-12-01

cegracation cf grapnite f cers in a~umnum was stuciea by Kohara arC Muto [201. reir stucv snowed a cecrease of 10 to 500, In ,n7e strenat cf cracn::e...eact:on procucts were identified by Kohara and MuLto (20] As an ,ustratLon one of the fibers from ,heir investigation is sin n -. 23. :2 t7elr -7...with puoishea worK. Kohara and Muto [20] suggested that the reaction procuct was A14C 3. 5.2 Mechanical Property Characterization of Fiber Reinforced

Study on erosion behaviour of hybrid aluminium composite

Science.gov (United States)

Vishwas, D. K.; Chandrappa, C. N.; Venkatesh, Shreyas

2018-04-01

The origin of the light metals, as compared to other metals in this century, is noticeable and an exciting area of expansion for innovation. Light metals, are need of the day in engineering, among them application of aluminium and its alloys is enormous. we observe that these metals tend to have a progressive loss of metal from having contact surface with other metals. Erosion is one such wear process, where damage occurs by the repeated application of high localised stresses. Erosion due to impact of solid particle, is a significant problem. In the present work, the erosion behaviour of hybrid aluminium composite is studied. AL 6061 is used as the base alloy. AL 6061 alloy has excellent corrosion resistance but poor wear resistance. So, in order to have improved properties, it is reinforced with Tungsten Chromium Nickel powder in varied proportions by the method of stir casting. The results are compared with the as-cast Al-alloy to determine the improvement in mechanical properties. The tests were conducted in ASTM G76 setup, to determine solid particle erosion behaviour and the results of the hybrid composite were compared with that of as-cast AL 6061 alloy. It was evident that mass loss was maximum at 300 inclinations, which is a characteristic of ductile materials. It was observed that upon increasing the percentages of reinforcement (wt.%), the wear resistance of the hybrid composite increased significantly. It was also observed that the inclusion of tungsten-chromium-nickel powder increased the hardness of the hybrid composite significantly.

Influence of Nickel Particle Reinforcement on Cyclic Fatigue and Final Fracture Behavior of a Magnesium Alloy Composite

Directory of Open Access Journals (Sweden)

Manoj Gupta

2012-06-01

Full Text Available The microstructure, tensile properties, cyclic stress amplitude fatigue response and final fracture behavior of a magnesium alloy, denoted as AZ31, discontinuously reinforced with nano-particulates of aluminum oxide and micron size nickel particles is presented and discussed. The tensile properties, high cycle fatigue and final fracture behavior of the discontinuously reinforced magnesium alloy are compared with the unreinforced counterpart (AZ31. The elastic modulus and yield strength of the dual particle reinforced magnesium alloy is marginally higher than of the unreinforced counterpart. However, the tensile strength of the composite is lower than the monolithic counterpart. The ductility quantified by elongation to failure over 0.5 inch (12.7 mm gage length of the test specimen showed minimal difference while the reduction in specimen cross-section area of the composite is higher than that of the monolithic counterpart. At the microscopic level, cyclic fatigue fractures of both the composite and the monolithic alloy clearly revealed features indicative of the occurrence of locally ductile and brittle mechanisms. Over the range of maximum stress and at two different load ratios the cyclic fatigue resistance of the magnesium alloy composite is superior to the monolithic counterpart. The mechanisms responsible for improved cyclic fatigue life and resultant fracture behavior of the composite microstructure are highlighted.

A comparative study on the tensile and impact properties of Kevlar, carbon, and S-glass/epoxy composites reinforced with SiC particles

Science.gov (United States)

Bulut, Mehmet; Alsaadi, Mohamad; Erkliğ, Ahmet

2018-02-01

Present study compares the tensile and impact characteristics of Kevlar, carbon and glass fiber reinforced composites with addition of microscale silicon carbide (SiC) within the common matrix of epoxy. The variation of tensile and impact strength values was explored for different content of SiC in the epoxy resin by weight (0, 5, 10, 15 and 20 wt%). Resulting failure characteristics were identified by assisting Charpy impact tests. The influence of interfacial adhesion between particle and fiber/matrix on failure and tensile properties was discussed from obtained results and scanning electron microscopy (SEM) figures. It is concluded from results that the content of SiC particles, and fiber types used as reinforcement are major parameters those effecting on tensile and impact resistance of composites as a result of different interface strength properties between particle-matrix and particle-fiber.

Effect of friction stir welding on microstructure, mechanical and wear properties of AA6061/ZrB2 in situ cast composites

International Nuclear Information System (INIS)

Dinaharan, I.; Murugan, N.

2012-01-01

Highlights: ► Application of FSW to join AA6061/ZrB 2 in situ composites. ► Homogenous distribution of ZrB 2 particles in the weld zone. ► Clusters in the parent composite are fragmented by the stirring action of the tool. ► Hardening of weld zone. ► FSW enhanced the wear resistance of the composite. - Abstract: Inadequate development of fabrication methods restricts the applications of new families of aluminum matrix composites (AMCs). Friction stir welding (FSW) is a potential candidate to join AMCs without any defects associated with conventional fusion welding processes. The primary objective of the present work is to apply FSW process to join AA6061/(0, 5 and 10 wt.%) ZrB 2 in situ cast composites and evaluate the joint properties. The composites were prepared by reacting inorganic salts K 2 ZrF 6 and KBF 4 with molten aluminum and joined using a FSW machine at a tool rotational speed of 1150 rpm, welding speed of 50 mm/min and axial force of 6 kN. The joints showed the presence of various zones such as weld zone (WZ), thermomechanically affected zone (TMAZ) and heat affected zone (HAZ). The weld zone was characterized with a homogenous distribution of ZrB 2 particles. The stirring action of the tool resulted in fragmentation of several clusters present in the parent composite. The weld zone exhibited higher hardness than that of the parent composite. The tensile strength of welded joints was comparable to that of parent composites. The wear resistance of the composites improved subsequent to FSW.

Mechanical clinching process stress and strain in the clinching of EN-AW5754 (AlMg3, and EN AW-5019 (AlMg5 metal plates

Directory of Open Access Journals (Sweden)

J. Cumin

2018-01-01

Full Text Available This paper presents the results of Finite Element Method numerical simulation performed onEN-AW5754(AlMg3, EN AW-5019 (AlMg5 plates subjected to mechanical clinching. The goal was to observe differences between aluminum plates in the same tool; and to determine the possibility of using the constructed tool for the clinching of Al-Al material combinations. This tool construction is to be produced and tested in laboratory conditions, to elaborate prospective results, and reach additional conclusions.

Acoustic wave (AW) based moisture sensor for use with corrosive gases

Science.gov (United States)

Pfeifer, K.B.; Frye, G.C.; Schneider, T.W.

1996-11-05

Moisture corrosive gas stream is measured as a function of the difference in resonant frequencies between two acoustic wave (AW) devices, each with a film which accepts at least one of the components of the gas stream. One AW is located in the gas stream while the other is located outside the gas stream but in the same thermal environment. In one embodiment, the film is a hydrophilic material such as SiO{sub 2}. In another embodiment, the SiO{sub 2} is covered with another film which is impermeable to the corrosive gas, such that the AW device in the gas stream measures only the water vapor. In yet another embodiment, the film comprises polyethylene oxide which is hydrophobic and measures only the partial pressure of the corrosive gas. Other embodiments allow for compensation of drift in the system. 8 figs.

Evaluation of alkaline dissolution of Al 6061 and Al 1050 for the production of Mo-99 from LEU targets

International Nuclear Information System (INIS)

Mindrisz, Ana C.; Camilo, Ruth L.; Araujo, Izilda C.; Forbicini, Christina A.L.G. de O.

2013-01-01

Since 2008, due to the global crisis in the production of radioisotope 99 Mo, which product of decay, 99m Tc, is the tracer element most often used in nuclear medicine and accounts for about 80% of all diagnostic procedures in vivo. Studies on the alkaline dissolution to obtain 9 9M o from irradiated UAl x -Al LEU targets are under development. Processing time should be minimized, considering the short half-life of 99 Mo and 99m Tc, about 66 h and 6 h, respectively. This makes dissolution time a significant factor in the development of the process. This paper presents the results of alkaline dissolution of 'scraps' of Al 6061 and 1050, used to simulate the dissolution process of UAl x -Al targets. Dissolution time and gas releasing were evaluated using the following alkaline solutions: a) NaOH 3 mol.L -1 and NaNO 3 2 mol.L -1 , b) NaOH 3 mol.L -1 and NaNO 3 4 mol.L -1 . The initial temperature of dissolution was 85 deg C in all cases. Al 6061 showed values of dissolution time greater than that for Al 1050, 25% for NaNO 3 2 mol.L -1 and 104.55% for NaNO 3 4 mol.L -1 . The dissolution with NaNO 3 2 mol.L -1 showed that the gas releasing for Al 6061 was 2.7% greater than for Al 1050. However Al 1050 showed that gas releasing 9.92% greater than for Al 6061 during the dissolution with NaNO 3 4 mol.L -1 . The decision about what type of alloy has to be used, Al 1050 or Al 6061, it will be upto the group that will manufacture the targets for the RMB. (author)

HIGH TEMPERATURE EROSION WEAR OF CERMET PARTICLES REINFORCED SELF-FLUXING ALLOY MATRIX HVOF SPRAYED COATINGS

Directory of Open Access Journals (Sweden)

Andrei Surzhenkov

2015-09-01

Full Text Available In the present paper, the resistance of high velocity oxy-fuel (HVOF sprayed TiC-NiMo and Cr3C2-Ni cermet particles reinforced NiCrSiB self-fluxing alloy matrix coatings to high temperature erosion wear is studied. Microstructure of the coatings was examined by SEM, phase composition was determined by XRD. A four-channel centrifugal particle accelerator was applied to study the high temperature erosion wear of the coatings. The impact angles were 30 and 90 degrees, initial particle velocity was 50 m/s, temperature of the test - 650 degrees. Volume wear of the coatings was calculated and compared to the respective values of the reference materials. Wear mechanisms were studied by SEM.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7617

A Preliminary Report on the Strength and Metallography of a Bimetallic Friction Stir Weld Joint Between AA6061 and MIL-DTL-46100E High Hardness Steel Armor

Science.gov (United States)

2012-11-26

bimetallic friction stir weld joint between AA6061 and MIL-DTL-46100E High Hardness steel armor. ABSTRACT One half inch thick plates of 6061-T6 aluminum...alloy and High Hardness steel armor (MIL- STD-46100) were successfully joined by the friction stir welding (FSW) process using a tungsten-rhenium...4. TITLE AND SUBTITLE A preliminary report on the strength and metallography of a bimetallic friction stir weld joint between AA6061 and MIL-DTL

Concurrent Haloalkanoate Degradation and Chlorate Reduction by Pseudomonas chloritidismutans AW-1T.

Science.gov (United States)

Peng, Peng; Zheng, Ying; Koehorst, Jasper J; Schaap, Peter J; Stams, Alfons J M; Smidt, Hauke; Atashgahi, Siavash

2017-06-15

Haloalkanoates are environmental pollutants that can be degraded aerobically by microorganisms producing hydrolytic dehalogenases. However, there is a lack of information about the anaerobic degradation of haloalkanoates. Genome analysis of Pseudomonas chloritidismutans AW-1 T , a facultative anaerobic chlorate-reducing bacterium, showed the presence of two putative haloacid dehalogenase genes, the l-DEX gene and dehI , encoding an l-2-haloacid dehalogenase (l-DEX) and a halocarboxylic acid dehydrogenase (DehI), respectively. Hence, we studied the concurrent degradation of haloalkanoates and chlorate as a yet-unexplored trait of strain AW-1 T The deduced amino acid sequences of l-DEX and DehI revealed 33 to 37% and 26 to 86% identities with biochemically/structurally characterized l-DEX and the d- and dl-2-haloacid dehalogenase enzymes, respectively. Physiological experiments confirmed that strain AW-1 T can grow on chloroacetate, bromoacetate, and both l- and d-α-halogenated propionates with chlorate as an electron acceptor. Interestingly, growth and haloalkanoate degradation were generally faster with chlorate as an electron acceptor than with oxygen as an electron acceptor. In line with this, analyses of l-DEX and DehI dehalogenase activities using cell-free extract (CFE) of strain AW-1 T grown on dl-2-chloropropionate under chlorate-reducing conditions showed up to 3.5-fold higher dehalogenase activity than the CFE obtained from AW-1 T cells grown on dl-2-chloropropionate under aerobic conditions. Reverse transcription-quantitative PCR showed that the l-DEX gene was expressed constitutively independently of the electron donor (haloalkanoates or acetate) or acceptor (chlorate or oxygen), whereas the expression of dehI was induced by haloalkanoates. Concurrent degradation of organic and inorganic halogenated compounds by strain AW-1 T represents a unique metabolic capacity in a single bacterium, providing a new piece of the puzzle of the microbial halogen cycle

Mechanical properties study of particles reinforced aluminum matrix composites by micro-indentation experiments

Directory of Open Access Journals (Sweden)

Yuan Zhanwei

2014-04-01

Full Text Available By using instrumental micro-indentation technique, the microhardness and Young’s modulus of SiC particles reinforced aluminum matrix composites were investigated with micro-compression-tester (MCT. The micro-indentation experiments were performed with different maximum loads, and with three loading speeds of 2.231, 4.462 and 19.368 mN/s respectively. During the investigation, matrix, particle and interface were tested by micro-indentation experiments. The results exhibit that the variations of Young’s modulus and microhardness at particle, matrix and interface were highly dependent on the loading conditions (maximum load and loading speed and the locations of indentation. Micro-indentation hardness experiments of matrix show the indentation size effects, i.e. the indentation hardness decreased with the indentation depth increasing. During the analysis, the effect of loading conditions on Young’s modulus and microhardness were explained. Besides, the elastic–plastic properties of matrix were analyzed. The validity of calculated results was identified by finite element simulation. And the simulation results had been preliminarily analyzed from statistical aspect.

Vacuum brazing of high volume fraction SiC particles reinforced aluminum matrix composites

Science.gov (United States)

Cheng, Dongfeng; Niu, Jitai; Gao, Zeng; Wang, Peng

2015-03-01

This experiment chooses A356 aluminum matrix composites containing 55% SiC particle reinforcing phase as the parent metal and Al-Si-Cu-Zn-Ni alloy metal as the filler metal. The brazing process is carried out in vacuum brazing furnace at the temperature of 550°C and 560°C for 3 min, respectively. The interfacial microstructures and fracture surfaces are investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and energy spectrum analysis (EDS). The result shows that adequacy of element diffusion are superior when brazing at 560°C, because of higher activity and liquidity. Dislocations and twins are observed at the interface between filler and composite due to the different expansion coefficient of the aluminum alloy matrix and SiC particles. The fracture analysis shows that the brittle fracture mainly located at interface of filler and composites.

Effect of heat treatment on microstructure and interface of SiC particle reinforced 2124 Al matrix composite

Energy Technology Data Exchange (ETDEWEB)

Mandal, Durbadal, E-mail: durbadal73@yahoo.co.in [MEF Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Viswanathan, Srinath [Dept of Metallurgical and Materials Engineering, University of Alabama, Tuscaloosa, AL (United States)

2013-11-15

The microstructure and interface between metal matrix and ceramic reinforcement of a composite play an important role in improving its properties. In the present investigation, the interface and intermetallic compound present in the samples were characterized to understand structural stability at an elevated temperature. Aluminum based 2124 alloy with 10 wt.% silicon carbide (SiC) particle reinforced composite was prepared through vortex method and the solid ingot was deformed by hot rolling for better particle distribution. Heat treatment of the composite was carried out at 575 °C with varying holding time from 1 to 48 h followed by water quenching. In this study, the microstructure and interface of the SiC particle reinforced Al based composites have been studied using optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive X-ray spectroscopy (EDS), electron probe micro-analyzer (EPMA) associated with wavelength dispersive spectroscopy (WDS) and transmission electron microscopy (TEM) to identify the precipitate and intermetallic phases that are formed during heat treatment. The SiC particles are uniformly distributed in the aluminum matrix. The microstructure analyses of Al–SiC composite after heat treatment reveal that a wide range of dispersed phases are formed at grain boundary and surrounding the SiC particles. The energy dispersive X-ray spectroscopy and wavelength dispersive spectroscopy analyses confirm that finely dispersed phases are CuAl{sub 2} and CuMgAl{sub 2} intermetallic and large spherical phases are Fe{sub 2}SiAl{sub 8} or Al{sub 15}(Fe,Mn){sub 3}Si. It is also observed that a continuous layer enriched with Cu and Mg of thickness 50–80 nm is formed at the interface in between Al and SiC particles. EDS analysis also confirms that Cu and Mg are segregated at the interface of the composite while no carbide is identified at the interface. - Highlights: • The composite was successfully heat treated at 575°C for 1

Rheological Studies on Pretreated Feed and Melter Feed from AW-101 and AN-107

International Nuclear Information System (INIS)

Bredt, Paul R; Swoboda, Robert G

2001-01-01

Rheological and physical properties testing were conducted on actual AN-107 and AW-101 pretreated feed samples prior to the addition of glass formers. Analyses were repeated following the addition of glass formers. The AN-107 and AW-101 pretreated feeds were tested at the target sodium values of nominally 6, 8, and 10 M. The AW-101 melter feeds were tested at these same concentrations, while the AN-107 melter feeds were tested at 5, 6, and 8 M with respect to sodium. These data on actual waste are required to validate and qualify results obtained with simulants

Joining of aluminum sheet and glass fiber reinforced polymer using extruded pins

Science.gov (United States)

Conte, Romina; Buhl, Johannes; Ambrogio, Giuseppina; Bambach, Markus

2018-05-01

The present contribution proposes a new approach for joining sheet metal and fiber reinforced composites. The joining process draws upon a Friction Stir Forming (FSF) process, which is performed on the metal sheet to produce slender pins. These pins are used to pierce through the composite. Joining is complete by forming a locking head out of the part if the pin sticks out of the composite. Pins of different diameters and lengths were produced from EN AW-1050 material, which were joined to glass fiber reinforced polyamide-6. The strength of the joint has been experimentally tested in order to understand the effect of the process temperature on the pins strength and therefore on the joining. The results demonstrate the feasibility of this new technique, which uses no excess material.

A polysaccharide isolated from Agaricus blazei Murill (ABP-AW1) as a potential Th1 immunity-stimulating adjuvant.

Science.gov (United States)

Cui, Liran; Sun, Yongxu; Xu, Hao; Xu, Huiyu; Cong, Huan; Liu, Jicheng

2013-10-01

In the present study, a low molecular weight polysaccharide, ABP-AW1, isolated from Agaricus blazei Murill was assessed for its potential adjuvant activity. ABP-AW1 is considered to create a 'depot' of antigen at a subcutaneous injection site. ICR mice were immunized with 100 μg ovalbumin (OVA) alone or with 100 μg OVA formulated in 0.9% saline containing 200 μg aluminum (alum) or ABP-AW1 (50, 100 and 200 μg) on days 1 and 15. Two weeks after the secondary immunization, splenocyte proliferation, the expression of surface markers, cytokine production and the OVA-specific antibody levels in the serum were determined. The OVA/ABP-AW1 vaccine, in comparison with OVA alone, markedly increased the proliferation of splenic lymphocytes and elicited greater antigen-specific CD4 + T cell activation, as determined by splenic CD4 + CD69 + T cells and Th1 cytokine interferon (IFN)-γ release. The combination of ABP-AW1 and OVA also enhanced IgG2b antibody responses to OVA. In conclusion, these data indicated that ABP-AW1 significantly enhanced the humoral and cellular immune responses against OVA in the mice, suggesting that ABP-AW1 stimulated Th1-type immunity. We suggest that ABP-AW1 may serve as a new adjuvant.

Study on preparation and properties of molybdenum alloys reinforced by nano-sized ZrO{sub 2} particles

Energy Technology Data Exchange (ETDEWEB)

Cui, Chaopeng; Gao, Yimin; Zhou, Yucheng [Xi' an Jiaotong University, State Key Laboratory for Mechanical Behavior of Materials, Xi' an, Shaanxi Province (China); Wei, Shizhong [Henan University of Science and Technology, School of Materials Science and Engineering, Luoyang (China); Henan University of Science and Technology, Engineering Research Center of Tribology and Materials Protection, Ministry of Education, Luoyang (China); Zhang, Guoshang; Zhu, Xiangwei; Guo, Songliang [Henan University of Science and Technology, School of Materials Science and Engineering, Luoyang (China)

2016-03-15

The nano-sized ZrO{sub 2}-reinforced Mo alloy was prepared by a hydrothermal method and a subsequent powder metallurgy process. During the hydrothermal process, the nano-sized ZrO{sub 2} particles were added into the Mo powder via the hydrothermal synthesis. The grain size of Mo powder decreases obviously with the addition of ZrO{sub 2} particles, and the fine-grain sintered structure is obtained correspondingly due to hereditation. In addition to a few of nano-sized ZrO{sub 2} particles in grain boundaries or sub-boundaries, most are dispersed in grains. The tensile strength and yield strength have been increased by 32.33 and 53.76 %. (orig.)

Mechanical behavior and fatigue performance of SMA short fiber reinforced MMC

Science.gov (United States)

Al-Matar, Basem Jawad

The mechanical behavior and performance of Shape Memory Alloy (SMA) short fiber NiTi reinforced Al was experimentally investigated for monotonic and fatigue test Al 6061 NiTi-SiC T6 was superior to unreinforced materials as well as to the reinforced Al T4. Taya three-dimensional model was performed on the monotonic tensile test at room temperature. It showed good agreement with experimental results. In order to utilize the compressive criterion for SMA, the NiTi reinforced Al composite was cooled at -10°C and prestrained at 1.2%. Beyond this limit composite suffered from damage. The net enhancement of SMA effect was around 10 MPa on composite yield stress. Results showed that the elastic constant for the composite did not change with loading and unloading suggesting that the inelastic behavior is plasticity. Further investigation on the inelastic behavior model as damage and/or plasticity by evaluating Poisson's ratio during loading was carried out by Adaptive Image Correlation Technique for Full-Field Strain Measurement. Poisson's ratio increased from around 0.33 to 0.5 demonstrating that it is plasticity that is responsible for the inelastic behavior. Scanning electron microscopy was also used and confirmed model results. The overall damage-behavior was quantified in terms of the post fatigue failure strength for low-cycle fatigue tests. Power law model was best to fit experimental findings.

Preparation and characterization of squeeze cast-Al–Si piston alloy reinforced by Ni and nano-Al2O3 particles

Directory of Open Access Journals (Sweden)

Hashem F. El-Labban

2016-07-01

Full Text Available Al–Si base composites reinforced with different mixtures of Ni and nano-Al2O3 particles have been fabricated by squeeze casting and their metallurgical and mechanical characterization has been investigated. A mixture of Ni and nano-Al2O3 particles of different ratios was added to the melted Al–Si piston alloy at 700 °C and stirred under pressure. After the Al-base-nano-composites were fabricated by squeeze casting, the microstructure and the particle distribution inside the matrix have been investigated using optical and scanning electron microscopes. Moreover, the hardness and the tensile properties of the resulted Al-base-nano-composites were evaluated at room temperature by using Vickers hardness and universal tensile testers, respectively. As a result, in most cases, it was found that the matrix showed a fine eutectic structure of short silicon constituent which appeared in the form of islands in the α-phase around some added particle agglomerations of the nano-composite structures. The tendency of this structure formation increases with the increase of Ni particle addition. As the ratio of the added particles increases, the tendency of these particles to be agglomerated also increases. Regarding the tensile properties of the fabricated Al-base-nano-composites, ultimate tensile strength is increased by adding the Ni and nano-Al2O3 particles up to 10 and 2 wt.%, respectively. Moreover, the ductility of the fabricated composites is significantly improved by increasing the added Ni particles. The composite material reinforced with 5 wt.% Ni and 2 wt.% nano-Al2O3 particles showed superior ultimate tensile strength and good ductility compared with any other added particles in this investigation.

Influence of Post Weld Heat Treatment on Strength of Three Aluminum Alloys Used in Light Poles

Directory of Open Access Journals (Sweden)

Craig C. Menzemer

2016-03-01

Full Text Available The conjoint influence of welding and artificial aging on mechanical properties were investigated for extrusions of aluminum alloy 6063, 6061, and 6005A. Uniaxial tensile tests were conducted on the aluminum alloys 6063-T4, 6061-T4, and 6005A-T1 in both the as-received (AR and as-welded (AW conditions. Tensile tests were also conducted on the AR and AW alloys, subsequent to artificial aging. The welding process used was gas metal arc (GMAW with spray transfer using 120–220 A of current at 22 V. The artificial aging used was a precipitation heat treatment for 6 h at 182 °C (360 °F. Tensile tests revealed the welded aluminum alloys to have lower strength, both for yield and ultimate tensile strength, when compared to the as-received un-welded counterpart. The beneficial influence of post weld heat treatment (PWHT on strength and ductility is presented and discussed in terms of current design provisions for welded aluminum light pole structures.

Effects of particle/matrix interfaces on the mechanical properties for SiCp or YAl2p reinforced Mg–Li composites

International Nuclear Information System (INIS)

Zhang, Q.Q.; Wu, G.Q.; Huang, Z.; Tao, Y.

2014-01-01

Highlights: • The particle/matrix interfaces in Mg–Li matrix composites are characterized. • The different reinforcement types with intermetallics and ceramics are considered. • The failure behaviors for the composites are successfully studied. • The effect of particle/matrix interface on the mechanical properties is discussed. -- Abstract: YAl 2p or SiC P reinforced Mg–14Li–3Al (LA143) matrix composites were prepared by stir-casting. The composites were subjected to fracture toughness and tensile tests. The particle/matrix interfaces were investigated by nanoindentation combined with scanning electron microscopy (SEM). The effects of the particle/matrix interfaces on the mechanical properties of the composites were discussed through a unit cell model with a transition interface layer. The results show that a transition interface layer with smoother hardness and modulus gradient is developed in the YAl 2 /LA143 composite. Both the fracture toughness and ductility for the YAl 2 /LA143 composite are higher than those for the SiC/LA143 composite. The failure behavior is determined by particle breakage with little interfacial breakage for the YAl 2 /LA143 composite, while being due to interfacial breakage for the SiC/LA143 composite. The superiority of the mechanical properties for the YAl 2 /LA143 composite may result from the failure behavior of particle breakage, which are correlated to the better physical compatibility between the YAl 2 intermetallics and LA143 matrix

Cytotoxicity properties of PM2.5 collected in Wrocław agglomeration

Directory of Open Access Journals (Sweden)

Bełcik Maciej Krzysztof

2017-01-01

Full Text Available WHO report published in May 2016 presents the cities with the highest concentrations of particulate matter fraction 10 μm and 2.5 μm on the earth. Report presents that many of Polish cities are on the top of polluted regions in European Union. One of the cities mentioned in the report is Wrocław. Wrocław is the urban and industrial agglomeration, where air pollutions comes from three main sources: low-emissions, industrial emissions and urban traffic. In recent years, reduction in annual average concentrations of particulate matter has been observed. However Wrocław is still one of the cities in Poland, which have problems with smog situations during winter season. This article presents results of researches conducted on the particulate matter fraction 2.5 μm collected in Wrocław agglomeration. Pollutions have been tested using PAN-I assay kit, which contains 4 single toxicity tests allows to check different parameters defining toxic effects on human cells. Cytotoxicity tests which are conducted are: LDH test to evaluate the integrity of cell membrane, XTT test to assess mitochondrial activity, NR test for the evaluation of the lysosomal activity and SRB test to evaluate the total protein content. Tests were performed on adenocarcinomic human alveolar basal epithelial cell line (A549, which allows to simulate conditions as close as real.

Thermal stability of segmented polyurethane elastomers reinforced by clay particles

Directory of Open Access Journals (Sweden)

Pavličević Jelena

2009-01-01

Full Text Available The aim of this work was to determine the influence of clay nanoparticles on thermal properties of segmented polyurethanes based on hexamethylene- diisocyanate, aliphatic polycarbonate diol and 1,4-butanediol as chain extender. The organically modified particles of montmorillonite and bentonite were used as reinforcing fillers. The structure of elastomeric materials was varied either by diol type or chain extender content. The ratio of OH groups from diol and chain extender (R was either 1 or 10. Thermal properties of prepared materials were determined using modulated differential scanning calorimetry (MDSC. Thermal stability of obtained elastomers has been studied by simultaneously thermogravimetry coupled with DSC. The glass transition temperature, Tg, of soft segments for all investigated samples was about -33°C. On the basis of DTG results, it was concluded that obtained materials were very stable up to 300°C.

Physical and Mechanical Properties of LoVAR: A New Lightweight Particle-Reinforced Fe-36Ni Alloy

Science.gov (United States)

Stephenson, Timothy; Tricker, David; Tarrant, Andrew; Michel, Robert; Clune, Jason

2015-01-01

Fe-36Ni is an alloy of choice for low thermal expansion coefficient (CTE) for optical, instrument and electrical applications in particular where dimensional stability is critical. This paper outlines the development of a particle-reinforced Fe-36Ni alloy that offers reduced density and lower CTE compared to the matrix alloy. A summary of processing capability will be given relating the composition and microstructure to mechanical and physical properties.

Fundamental Study of Electron Beam Welding of AA6061-T6 Aluminum Alloy for Nuclear Fuel Plate Assembly (II)

International Nuclear Information System (INIS)

Kim, Soosung; Lee, Haein; Lee, Donbae; Park, Jongman; Lee, Yoonsang

2013-01-01

Certain characteristics, such as solidification cracking, porosity, HAZ (Heat-affected Zone) degradation must be considered during welding. Because of high energy density and low heat input, especially LBW and EBW processes posses the advantage of minimizing the fusing zone and HAZ and producing deeper penetration than arc welding processes. In present study, to apply for the nuclear fuel plate fabrication and assembly, a fundamental EBW experiment using AA6061-T6 aluminum alloy specimens was conducted. Furthermore, to establish the welding process, and satisfy the requirements of the weld quality, EBW apparatus using a electron welding gun and vacuum chamber was developed, and preliminary investigations for optimizing the welding parameters of the specimens using AA6061-T6 aluminum plates were also performed. In this experiment, a feasibility test was carried out by tensile tester, bead-on-plate welding and metallographic examination to comply with the aluminum welding procedure. The EB weld quality of AA6061-T6 aluminum alloy for the fuel plate assembly has been also studied by the mechanical testing and microstructure examinations. This study was carried out to determine the suitable welding process and to investigate tensile strength of AA6061-T6 aluminum alloy. In the present experiment, satisfactory EBW of the square butt weld specimens was developed. In comparison with the rolling directions of test specimens, the tensile strengths were no difference between the longitudinal and transverse welds. Based on this fundamental study, fabrication and assembly of the nuclear fuel plates will be provided for the future Kijang research reactor project

A Case Study for the Welding of Dissimilar EN AW 6082 and EN AW 5083 Aluminum Alloys by Friction Stir Welding

Directory of Open Access Journals (Sweden)

Sefika Kasman

2016-12-01

Full Text Available The aim of this study is to investigate the effect of keeping constant the tool rotational speed to the welding speed ratio (υ ratio on the mechanical properties of the dissimilar friction stir welding of EN AW6082-T6 and EN AW5083-H111. Two different pins shaped as triangular and pentagonal were associated with the constant υ ratio. From the tensile test results, it was found that the υ ratio does not create an evident change in the weld joint strength. The small cavity- and tunnel-type defects were observed at the nugget zone and located on the advancing side of the pin. These defects caused a decrease in the strength and elongation of the weld joint. The most important inference obtained from the experimental results is that if the υ ratio is kept constant, the weld joint strength for each weld does not correspond to a constant value.

Plasma source ion implantation process for corrosion protection of 6061 aluminum

International Nuclear Information System (INIS)

Zhang, L.; Booske, J.H.; Shohet, J.L.; Jacobs, J.R.; Bernardini, A.J.

1995-01-01

This paper describes results of an investigation of the feasibility of using nitrogen plasma source ion implantation (PSII) treatment to improve corrosion resistance of 6061 aluminum to salt water. Flat Al samples were implanted with various doses of nitrogen. The surface microstructures and profiles of Al and N in the flat samples were examined using transmission electron microscopy (TEM), scanning Auger microprobe, x-ray diffraction. Corrosion properties of the samples and the components were evaluated using both a 500 hour salt spray field test and a laboratory electrochemical corrosion system. The tested samples were then analyzed by scanning electron microscopy. Corrosion measurements have demonstrated that PSII can significantly improve the pitting resistance of 6061 aluminum. By correlating the analytical results with the corrosion test results, it has been verified that the improved corrosion resistance in PSII-treated coupons is due to the formation of a continuous AlN layer. It was also identified that the formation of a continuous AlN layer. It was also identified that the formation of a continuous AlN layer is mainly determined by the bias voltage and the total integrated implantation dose, and relatively insensitive to factors such as the plasma source, pulse length, or frequency

Evaluation of the corrosion resistance of anodized aluminum 6061 using electrochemical impedance spectroscopy (EIS)

International Nuclear Information System (INIS)

Huang Yuelong; Shih Hong; Huang, Huochuan; Daugherty, John; Wu Shun; Ramanathan, Sivakami; Chang, Chris; Mansfeld, Florian

2008-01-01

The corrosion resistance of anodized Al 6061 produced by two different anodizing and sealing processes was evaluated using electrochemical impedance spectroscopy (EIS). The scanning electron microscope (SEM) was employed to determine the surface structure and the thickness of the anodized layers. The EIS data revealed that there was very little change of the properties of the anodized layers for samples that were hard anodized in a mixed acid solution and sealed in hot water over a 365 day exposure period in a 3.5 wt% NaCl solution. The specific admittance A s and the breakpoint frequency f b remained constant with exposure time confirming that the hard anodizing process used in this study was very effective in providing excellent corrosion resistance of anodized Al 6061 over extended exposure periods. Some minor degradation of the protective properties of the anodized layers was observed for samples that were hard anodized in H 2 SO 4 and exposed to the NaCl solution for 14 days

Electrochemical corrosion characteristics of aluminium alloy 6061 T6 in demineralized water containing 0.1 % chloride ion

International Nuclear Information System (INIS)

Zaifol Samsu; Muhammad Daud; Siti Radiah Mohd Kamarudin; Mohd Saari Ripin; Rusni Rejab; Mohd Shariff Sattar

2012-01-01

Direct current electrochemical method is one of the techniques has been used to study the corrosion behaviour of metal/alloy in its environment. This paper attempts to investigate the corrosion behaviour of Al 6061 T6 immersed in Reactor TRIGA Mark II pool water containing about 0.1% NaCl content. The result shown that the corrosion rate value of the aluminium 6061 T6 increased with the presence of 0.1 % Ion Chloride content in the demineralized water reactor pool as compared to normal demineralized water. This is due to aggressiveness of chloride ion attack to metal surface. Beside corrosion rate analysis, the further tests such as corrosion behaviour diagram, cyclic polarization have been carried and the results have been reported. (author)

Comparison of Pentax-AWS Airwayscope and Glidescope for Infant Tracheal Intubation by Anesthesiologists during Cardiopulmonary Arrest Simulation: A Randomized Crossover Trial

Directory of Open Access Journals (Sweden)

Shunsuke Fujiwara

2015-01-01

Full Text Available Background. Recent guidelines for infant cardiopulmonary resuscitation emphasize that all rescuers should minimize interruption of chest compressions, even for endotracheal intubation. We compared the utility of the Pentax-AWS Airwayscope (AWS with the Glidescope (GS during chest compressions on an infant manikin. Methods. Twenty-four anesthesiologists with more than two years of experience performed tracheal intubation on an infant manikin using the AWS and GS, with or without chest compressions. Results. In GS trials, none of the participants failed without compressions, while three failed with compressions. In AWS trials, all participants succeeded regardless of chest compressions. Intubation time was significantly longer with chest compressions with the GS (P<0.05, but not with the AWS. Difficulty of operation on a visual analog scale (VAS for laryngoscopy did not increase significantly with chest compressions with either the GS or the AWS, while the VAS for tube passage through the glottis increased with compressions with the GS, but not with the AWS. Conclusion. We conclude that in infant simulations managed by anesthesiologists, the AWS performed better than the GS for endotracheal intubation with chest compressions.

Microstructure and microtexture studies of a friction stir welded Al 6061 alloy

International Nuclear Information System (INIS)

Kumbhar, N.T.; Tewari, R.; Dey, G.K.; Bhanumurthy, K.; Sahoo, S.K.; Samajdar, I.

2009-01-01

Friction stir welding is a solid state joining technique used extensively for the joining of various metals and alloys and also has been applied to the joining of steels. The friction stir welding of Al and its alloys has been extensively delt with over a period exceeding the last decade and a half due to its numerous advantages over other conventional fusion welding techniques in terms of weld quality, efficiency, cost effectiveness etc. to name a few. This technique is being increasingly seeked by industries in mass production/engineering such as the railways, marine and aerospace industries. The friction stir welding of a precipitation hardened Al 6061 alloy plates of 6 mm. thickness was performed at various tool rotation speeds and tool traverse speeds with a constant tilt of 3 deg using a high strength steel (HSS) tool of appropriate dimensions. The cross section of the weld perpendicular to the welding direction was analyzed for a detailed microstructural investigation using electron probe microanalysis, orientation imaging microscopy and transmission electron microscopy. Various microstructural changes are observed in the various regions of the friction stir welded AA 6061. The nugget region which is highly deformed is characterized by the dissolution and reprecipitation of the coarse precipitates, grain size refinement and recrystallization. The adjoining regions near the nugget viz the thermomechanically affected zone (TMAZ) and the heat affected zone (HAZ) also show heterogeneous microstructure in terms of grain size and precipitation which is mainly attributed to the heating cycle experienced during welding. This heterogeneity is also evident from the plot of microhardness distribution across the cross section of the weld region. However, the electron probe microanalysis studies do not show any significant pickup of oxygen in the weld interior as compared to a little oxygen pickup upto 30 μm from the top surface. Further, using orientation imaging

Thermal modeling of tanks 241-AW-101 and 241-AN-104 with the TEMPEST code

International Nuclear Information System (INIS)

Antoniak, Z.I.; Recknagle, K.P.

1995-07-01

The TEMPEST code was exercised in a preliminary study of double-shell Tanks 241 -AW-101 and 241-AN-104 thermal behavior. The two-dimensional model used is derived from our earlier studies on heat transfer from Tank 241-SY-101. Several changes were made to the model to simulate the waste and conditions in 241-AW-101 and 241-AN-104. The nonconvective waste layer was assumed to be 254 cm (100 in.) thick for Tank 241-AW-101, and 381 cm (150 in.) in Tank 241-AN-104. The remaining waste was assumed, for each tank, to consist of a convective layer with a 7.6-cm (3-inch) crust on top. The waste heat loads for 241-AW-101 and 241-AN-104 were taken to be 10 kW (3.4E4 Btu/hr) and 12 kW (4.0E4 Btu/hr), respectively. Present model predictions of maximum and convecting waste temperatures are within 1.7 degrees C (3 degrees F) of those measured in Tanks 241-AW-101 and 241-AN-104. The difference between the predicted and measured temperature is comparable to the uncertainty of the measurement equipment. These models, therefore, are suitable for estimating the temperatures within the tanks in the event of changing air flows, waste levels, and/or waste configurations

Reinforcement of Conducting Silver-based Materials

Directory of Open Access Journals (Sweden)

Heike JUNG

2014-09-01

Full Text Available Silver is a well-known material in the field of contact materials because of its high electrical and thermal conductivity. However, due to its bad mechanical and switching properties, silver alloys or reinforcements of the ductile silver matrix are required. Different reinforcements, e. g. tungsten, tungsten carbide, nickel, cadmium oxide or tin oxide, are used in different sectors of switches. To reach an optimal distribution of these reinforcements, various manufacturing techniques (e. g. powder blending, preform infiltration, wet-chemical methods, internal oxidation are being used for the production of these contact materials. Each of these manufacturing routes offers different advantages and disadvantages. The mechanical alloying process displays a successful and efficient method to produce particle-reinforced metal-matrix composite powders. This contribution presents the obtained fine disperse microstructure of tungsten-particle-reinforced silver composite powders produced by the mechanical alloying process and displays this technique as possible route to provide feedstock powders for subsequent consolidation processes. DOI: http://dx.doi.org/10.5755/j01.ms.20.3.4889

Development of dispersion U(Mo)/Al–Si miniplates fabricated at 500 °C with Al 6061 as cladding

Energy Technology Data Exchange (ETDEWEB)

Mirandou, M.I., E-mail: mirandou@cnea.gov.ar [Gerencia Materiales-GAEN-CNEA, Avda. Gral. Paz 1499, B1650KNA San Martín, Buenos Aires (Argentina); Aricó, S.F. [Gerencia Materiales-GAEN-CNEA, Avda. Gral. Paz 1499, B1650KNA San Martín, Buenos Aires (Argentina); Instituto Sabato UNSAM-CNEA, Avda. Gral. Paz 1499, B1650KNA San Martín, Buenos Aires (Argentina); Balart, S.N. [Gerencia Materiales-GAEN-CNEA, Avda. Gral. Paz 1499, B1650KNA San Martín, Buenos Aires (Argentina); Fabro, J.O. [Departamento ECRI, Gerencia de Ciclo del Combustible Nuclear, CNEA, Avda. Gral. Paz 1499, B1650KNA San Martín, Buenos Aires (Argentina)

2015-02-15

In the frame of U(Mo) dispersion fuel elements qualification, Si additions to Al matrix arose as a promising solution to the unacceptable failures found when pure Al is used. Analysis of as-fabricated fuel plates made with Al–Si matrices demonstrated that good irradiation behavior is correlated with the formation during fabrication of a Si-containing interaction layer around the U(Mo) particles. Thus, the analysis of the influence of fabrication parameters becomes important. Studies on Al–Si dispersion miniplates fabricated in CNEA, Argentina, have been initiated to determine how to obtain the better interaction layer characteristics with the lesser modifications to the fabrication process and the smaller amount of Si in the matrix. In this work results for miniplates made of atomized U–7 wt%Mo particles dispersed in Al–2 wt%Si and Al–4 wt%Si matrices, obtained by mixing pure Al and Si powders, and Al 6061 as cladding are presented. Interaction layer grown during fabrication process (500 °C) consists of Si-containing phases being U(Al, Si){sub 3} its principal component. Its uniformity is not satisfactory due to the formation of an oxide layer.

The Awá-Guajá Indians of the Brazilian Amazon. Demographic data, serum protein markers and blood groups.

Science.gov (United States)

de Oliveira, S F; Lopes, D E; Santos, S E; Guerreiro, J F

1998-01-01

The South-American Indian group Awá-Guajá, currently living in the State of Maranhão (Northeastern Brazil), is one of the most recently contacted Indian groups of the Brazilian Amazon. This group is made up by three partially isolated villages named Awá, Guajá and Juriti, and is characterized by having a young population, in which 47.6% of the individuals range from 0 to 14 years old. The sex ratios (male/female) for people of reproductive age are 1.13 for Awá village, 2.00 for Guajá, 3.33 for Juriti and 1.61 for the tribe as a whole. Fst and heterogeneity analysis show that, despite the small differences observed among villages for the eight genetic systems analyzed, the Awá-Guajá tribe is constituted of only one population. Furthermore, comparisons between Awá-Guajá and Urubú-Kaapor tribes indicate that they are still isolated genetically, in spite of the fact that they share territories.

The analysis of composite properties reinforced with particles from palm oil industry waste produced by casting methods

Science.gov (United States)

Tugiman; Ariani, F.; Taher, F.; Hasibuan, M. S.; Suprianto

2017-12-01

Palm oil processing industries are very attractive because they offer plenty products with high economic value. The CPO factory processes not only produces crude palm oil but also generates fly ash (FA) particles waste in its final process. The purpose of this investigation to analyze and increase the benefits of particles as reinforcement materials for fabricating aluminum matrix composites (AMC’s) by different casting route. Stirring, centrifugal and squeeze casting method was conducted in this study. Further, the chemical composition of FA particles, densities and mechanical properties have been analyzed. The characteristics of composite material were investigated using an Optical microscope, scanning electron microscope (SEM), hardness (Brinell), impact strength (Charpy). The pin on disc method was used to measure the wear rate. The results show that SiO2, Fe2O3, and Al2O3 are the main compounds of fly ash particles. These particles enhanced the hardness and reduce wear resistance of aluminum matrix composites. The squeeze method gives better results than stir and centrifugal casting.

Tank characterization report for double-shell Tank 241-AW-105

International Nuclear Information System (INIS)

DiCenso, A.T.; Amato, L.C.; Franklin, J.D.; Lambie, R.W.; Stephens, R.H.; Simpson, B.C.

1994-01-01

In May 1990, double-shell Tank 241-AW-105 was sampled to determine proper handling of the waste, to address corrosivity and compatibility issues, and to comply with requirements of the Washington Administrative Code. This Tank Characterization Report presents an overview of that tank sampling and analysis effort, and contains observations regarding waste characteristics. It also addresses expected concentration and bulk inventory data for the waste contents based on this latest sampling data and background tank information. This report summarizes the available information regarding the waste in Tank 241-AW-105, and using the historical information to place the analytical data in context, arranges this information in a useful format for making management and technical decisions concerning this waste tank. In addition, conclusions and recommendations are given based on safety issues and further characterization needs

Microstructural Characterization of the U-9.1Mo Fuel/AA6061 Cladding Interface in Friction-Bonded Monolithic Fuel Plates Irradiated in the RERTR-6 Experiment

Science.gov (United States)

Keiser, Dennis D.; Jue, Jan-Fong; Miller, Brandon; Gan, Jian; Robinson, Adam; Medvedev, Pavel; Madden, James; Wachs, Dan; Clark, Curtis; Meyer, Mitch

2015-09-01

Low-enrichment (235U < 20 pct) U-Mo monolithic fuel is being developed for use in research and test reactors. The earliest design for this fuel that was investigated via reactor testing consisted of a nominally U-10Mo fuel foil encased in AA6061 (Al-6061) cladding. For a fuel design to be deemed adequate for final use in a reactor, it must maintain dimensional stability and retain fission products throughout irradiation, which means that there must be good integrity at the fuel foil/cladding interface. To investigate the nature of the fuel/cladding interface for this fuel type after irradiation, fuel plates were fabricated using a friction bonding process, tested in INL's advanced test reactor (ATR), and then subsequently characterized using optical metallography, scanning electron microscopy, and transmission electron microscopy. Results of this characterization showed that the fuel/cladding interaction layers present at the U-Mo fuel/AA6061 cladding interface after fabrication became amorphous during irradiation. Up to two main interaction layers, based on composition, could be found at the fuel/cladding interface, depending on location. After irradiation, an Al-rich layer contained very few fission gas bubbles, but did exhibit Xe enrichment near the AA6061 cladding interface. Another layer, which contained more Si, had more observable fission gas bubbles. In the samples produced using a focused ion beam at the interaction zone/AA6061 cladding interface, possible indications of porosity/debonding were found, which suggested that the interface in this location is relatively weak.

Thermal and mechanical behavior of metal matrix and ceramic matrix composites

Science.gov (United States)

Kennedy, John M. (Editor); Moeller, Helen H. (Editor); Johnson, W. S. (Editor)

1990-01-01

The present conference discusses local stresses in metal-matrix composites (MMCs) subjected to thermal and mechanical loads, the computational simulation of high-temperature MMCs' cyclic behavior, an analysis of a ceramic-matrix composite (CMC) flexure specimen, and a plasticity analysis of fibrous composite laminates under thermomechanical loads. Also discussed are a comparison of methods for determining the fiber-matrix interface frictional stresses of CMCs, the monotonic and cyclic behavior of an SiC/calcium aluminosilicate CMC, the mechanical and thermal properties of an SiC particle-reinforced Al alloy MMC, the temperature-dependent tensile and shear response of a graphite-reinforced 6061 Al-alloy MMC, the fiber/matrix interface bonding strength of MMCs, and fatigue crack growth in an Al2O3 short fiber-reinforced Al-2Mg matrix MMC.

[Caries of permanent dentition in medieval inhabitants of Wrocław].

Science.gov (United States)

Staniowski, Tomasz; Dabrowski, Paweł; Gawlikowska-Sroka, Aleksandra

2011-01-01

The study of dentition plays an important role in the reconstruction of the diet and in assessment of the overall health and living conditions of paleopopulations. The aim of this study was to determine the condition of permanent dentition of medieval inhabitants of Wrocław basing on the prevalence and intensity of caries in permanent dentition. The material consisted of 1156 permanent teeth from 118 skulls recovered from two medieval cemeteries in Wrocław: the parish cemetery at the St. Elisabeth Church (13th-14th century) and the cemetery in Ołbin (12th-13th century). Two age classes were formed taking into account anthropologic assessment and group size. The younger class consisted of material up to the age of 35 years; the remaining skulls were assigned to the older class. The prevalence and incidence of caries was determined. The prevalence and intensity of caries was 56.91% and 15.7%, respectively. Carious lesions predominated in males and in the older age class. The prevalence and intensity of caries in permanent dentition did not differ from other medieval populations and increased with age. High prevalence of caries reflects a high proportion of carbohydrates in the diet of medieval inhabitants of Wrocław, their high socioeconomic status, and poor oral hygiene.

Influence of Friction Stir Welding (FSW on Mechanical and Corrosion Properties of AW-7020M and Aw-7020 Alloys

Directory of Open Access Journals (Sweden)

Dudzik Krzysztof

2016-09-01

Full Text Available Friction welding associated with mixing the weld material (FSW - Friction Stir Welding is an alternative to MIG and TIG welding techniques for Al-alloys. This paper presents experimental results obtained from static tension tests on specimens made of AW-7020M and AW-7020 alloys and their joints welded by using FSW method carried out on flat specimens, according to Polish standards : PN-EN ISO 4136:2011 and PN-EN ISO 6892-1:2010. Results of corrosion resistance tests are also presented. The tests were performed by using the electrochemical impedance spectroscopy (EIS. EIS measurement was conducted with the use of three-electrode system in a substitute sea water environment (3,5% NaCl - water solution. The impedance tests were carried out under corrosion potential. Voltage signal amplitude was equal to 10mV, and its frequency range - 100 kHz ÷ 0,1 Hz. Atlas 0531 EU&IA potentiostat was used for the tests. For the tested object an equivalent model was selected in the form of a substitute electric circuit. Results of the impedance spectroscopy tests are presented in the form of parameters which characterize corrosion process, as well as on Nyquist’s graphs together with the best-fit theoretical curve.

Evaluation of the corrosion resistance of anodized aluminum 6061 using electrochemical impedance spectroscopy (EIS)

Energy Technology Data Exchange (ETDEWEB)

Huang Yuelong [Corrosion and Environmental Effects Laboratory (CEEL), Mork Family Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-0241 (United States); Shih Hong [Lam Research Corporation, 4400 Cushing Parkway, Fremont, CA 94538 (United States)], E-mail: hong.shih@lamrc.com; Huang, Huochuan; Daugherty, John; Wu Shun; Ramanathan, Sivakami; Chang, Chris [Lam Research Corporation, 4400 Cushing Parkway, Fremont, CA 94538 (United States); Mansfeld, Florian [Corrosion and Environmental Effects Laboratory (CEEL), Mork Family Department of Chemical Engineering and Materials Science, University of Southern California, Los Angeles, CA 90089-0241 (United States)], E-mail: mansfeld@usc.edu

2008-12-15

The corrosion resistance of anodized Al 6061 produced by two different anodizing and sealing processes was evaluated using electrochemical impedance spectroscopy (EIS). The scanning electron microscope (SEM) was employed to determine the surface structure and the thickness of the anodized layers. The EIS data revealed that there was very little change of the properties of the anodized layers for samples that were hard anodized in a mixed acid solution and sealed in hot water over a 365 day exposure period in a 3.5 wt% NaCl solution. The specific admittance A{sub s} and the breakpoint frequency f{sub b} remained constant with exposure time confirming that the hard anodizing process used in this study was very effective in providing excellent corrosion resistance of anodized Al 6061 over extended exposure periods. Some minor degradation of the protective properties of the anodized layers was observed for samples that were hard anodized in H{sub 2}SO{sub 4} and exposed to the NaCl solution for 14 days.

The effects of irradiation to 8x1026m-2 on the mechanical properties of 6061-T651 aluminum

International Nuclear Information System (INIS)

Alexander, D.J.

1995-01-01

The effects of irradiation on the mechanical properties of candidate structural materials are being examined. A key to the generation of useful neutron beams is allowing the neutrons produced in the core to escape. Therefore, an aluminum alloy has been selected for the first wall containment adjacent to the core, the Core Pressure Boundary Tube (CPBT), Alloy (6061 J651 Al 1.0Mg-0.6Si-0.3Cu-0.2Cr) with acceptable mechanical properties in unirradiated condition, low neutron cross-section, high thermal conductivity for heat removal. This alloy may also be used for the beam tubes and reflector tank. An irradiation program is underway to determine the effects of irradiation on the mechanical properties of 6061-T651 aluminium in particular the fracture toughness. This data will allow the operating lifetime of the CPBT to determined which will in turn determine its replacement schedule in the ANS. The first two capsules for the ANS Irradiation Effects program have been successfully irradiated to 10 26 and 8x10 26 m -2 (thermal flux), respectively, at a nominal irradiation temperature of 95 deg. C. The testing of the specimens of 6061-T651 aluminum has shown: 1. The yield and ultimate tensile strengths are increased by irradiation; 2. The uniform and total elongations are reduced, but useful ductility remains, even at the higher irradiation level; 3. The fracture toughness at 25 deg. C and 95 deg. C is unaffected by irradiation, but at 150 deg. C, it decreases with an increase in irradiation; 4. The tearing modulus of 6061-T651 is low in the unirradiated condition, and is reduced to very low values by irradiation. This alloy also shows a tendency for sudden unstable crack extension

{sup 10}B areal density: A novel approach for design and fabrication of B{sub 4}C/6061Al neutron absorbing materials

Energy Technology Data Exchange (ETDEWEB)

Li, Yuli [School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Wang, Wenxian, E-mail: wangwenxian@tyut.edu.cn [School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Zhou, Jun [School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Department of Mechanical Engineering, Pennsylvania State University Erie, The Behrend College, Erie, PA 16563 (United States); Chen, Hongsheng [School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); Key Laboratory of Interface Science and Engineering in Advanced Materials, Ministry of Education, Taiyuan University of Technology, Taiyuan 030024 (China); Zhang, Peng [School of Materials Science and Engineering, Taiyuan University of Technology, Taiyuan 030024 (China); College of Physics and Optoelectronics, Taiyuan University of Technology, Taiyuan 030024 (China)

2017-04-15

In this paper, a novel approach to evaluate the neutron shielding performance of a boron-containing neutron absorbing material was proposed for the first time through the establishment of a direct relationship between {sup 10}B areal density ({sup 10}BAD) of the material and its neutron absorption ratio. It is found when the {sup 10}BAD of a material is greater than 0.034 g/cm{sup 2}, the material will achieve a good neutron shielding performance. Based on this proposed approach, B{sub 4}C/6061Al composite plates with different B{sub 4}C content (10 wt%, 20 wt%, 30 wt%) were successfully fabricated using vacuum hot pressing followed by hot-extrusion. The characteristics of the B{sub 4}C/Al interface were studied in details using transmission electron microscopy (TEM), and the effects of B{sub 4}C particle content on microstructure and mechanical properties of the Al matrix were investigated. Through current studies, B{sub 4}C/6061Al composite plates possessing good neutron shielding performance and tensile strength are found to be able to be fabricated using either 20 wt% of B{sub 4}C content with a plate thickness of 4.5 mm or 30 wt% B{sub 4}C content with a plate thickness of 3 mm. - Graphical abstract: In this paper, a novel approach to evaluate the neutron shielding ability of a boron-containing neutron shielding material was proposed for the first time through the establishment of a direct relationship between {sup 10}B area density ({sup 10}BAD) of the material and its neutron shielding ratio. - Highlights: •{sup 10}BAD was proposed to evaluate the boron-containing neutron absorber material’s neutron shielding performance. •The direct relationship between the {sup 10}BAD and neutron shielding performance was firstly established. •TEM analysis of the composites reveals that an amorphous layer exists at the Al/B{sub 4}C interface. •Suitable B{sub 4}C contents and thickness for the fabrication of B{sub 4}C/6061A1 NAC plate were given in the

Effects of TiB2 Particle and Short Fiber Sizes on the Microstructure and Properties of TiB2-Reinforced Composite Coatings

Science.gov (United States)

Lin, Yinghua; Yao, Jianhua; Wang, Liang; Zhang, Qunli; Li, Xueqiao; Lei, Yongping; Fu, Hanguang

2018-03-01

In this study, particle and short fiber-reinforced titanium matrix composite coatings are prepared via laser in situ technique using (0.5 and 50 μm) TiB2 and Ti powder as cladding materials. The microstructure and properties of the composite coatings are studied, and the changing mechanism of the microstructure is discussed. The results reveal that particle agglomeration is prone to appear with using fine TiB2 particles. Decomposition of the particles preferentially occurs with using coarse TiB2 particles. The cracks and pores on the surface of the coating are formed at a lower laser energy density. With the increase in the laser energy density, cracking on the surface of the coating diminishes, but the coating exhibits depression behavior. The depression extent of the coating using fine TiB2 particle as the reinforcement is much less than that of the coating using coarse TiB2 particle. Moreover, the size of the aggregate and the tendency of cracking can be reduced with the increase in Ti addition. Meanwhile, short TiB fiber bundles are formed by the diffusion mechanism of rod aggregate, and randomly oriented TiB short fibers are formed mainly by the dissolution-precipitation mechanism of fine TiB2 particles. Moreover, the growth of short TiB fibers can be in an alternating manner between B27 and Bf structures. The micro-hardness and wear resistance of the coatings are evidently higher than that of the titanium alloy substrate. The wear resistance of the large size TiB2 coating is higher than that of the small size TiB2 coating under the condition of low load.

High-strength bolt-forming of fine-grained aluminum alloy 6061 with a continuous hybrid process

International Nuclear Information System (INIS)

Kim, Ji Hun; Hwang, Sun Kwang; Im, Yong-Taek; Son, Il-Heon; Bae, Chul Min

2012-01-01

Highlights: ► Fine-grained AA6061-O was produced by a continuous hybrid process. ► It consists of rolling, ECAP, and drawing. ► High-strength bolt was manufactured with the fine-grained AA6061-O. ► The UTS and micro-hardness of the bolt was increased by 50%. ► The route C was better in making a uniform micro-hardness distribution in the bolt. - Abstract: It is well known that the development of a continuous manufacturing process to apply severe plastic deformation (SPD) is a major challenge for industrial usages to improve the mechanical properties of the material through grain refinement. In this study, fine-grained AA6061-O wire was manufactured by a two-pass hybrid process consisting of drawing, equal channel angular pressing and rolling in a continuous manner to investigate the effects of processing routes for two different routes, A and C, on the variation of ultimate tensile strength (UTS) and micro-hardness distribution. The UTS value (185 MPa) of the specimen processed by the two-pass hybrid process with route A was higher than that of 171 MPa obtained from the two-pass wire-drawing process and was equivalent to the level of 184 MPa processed by the three-pass wire-drawing process. The average micro-hardness value (Hv 58.0) obtained from the two-pass hybrid process through route C was the highest among all the cases. According to transmission electron microscopy, the original grain was subdivided and elongated owing to deformation during the processes. The specimen processed by the two-pass hybrid process through route C showed smaller deformation bands and had potentially higher angle grain boundaries compared to the specimen processed by the two-pass wire-drawing process. Finally, the high-strength bolt was manufactured using the fine-grained AA6061-O wire prepared by the continuous hybrid process to check its formability. A ductile fracture at the first thread right above the jaw was observed in the bolt tension test of the manufactured bolt

Tank characterization report for double-shell tank 241-AW-102

International Nuclear Information System (INIS)

Bell, K.E.

1997-01-01

This document summarizes the information on the historical uses, present status, and the sampling and analysis results of waste stored in Tank 241-AW-102. This report supports the requirements of the Tri-Party Agreement Milestone M-44-05

Tank characterization report for double-shell tank 241-AW-102

Energy Technology Data Exchange (ETDEWEB)

Bell, K.E.

1997-05-29

This document summarizes the information on the historical uses, present status, and the sampling and analysis results of waste stored in Tank 241-AW-102. This report supports the requirements of the Tri-Party Agreement Milestone M-44-05.

The fracture toughness and DBTT of MoB particle-reinforced MoSi2 composites

International Nuclear Information System (INIS)

Xiong Zhi; Wang Gang; Jiang Wan

2005-01-01

The room temperature fracture toughness and the high temperature DBTT of MoB particle-reinforced MoSi 2 composites were investigated using Vickers indentation technique and MSP testing method, respectively. Modified small punch (MSP) test is a method for evaluation of mechanical properties using very small specimens, and it's appropriate for the determination of strength and DBTT. It was found that the approximate fracture toughness of the composite is 1.3 times that of monolithic MoSi 2 , and its DBTT is 100 C higher than that of monolithic MoSi 2 materials. Cracks deflection is a probable mechanism responsible for this behavior. (orig.)

Fabrication of Al5083 surface composites reinforced by CNTs and cerium oxide nano particles via friction stir processing

Energy Technology Data Exchange (ETDEWEB)

Hosseini, S.A. [Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz (Iran, Islamic Republic of); Ranjbar, Khalil, E-mail: k_ranjbar@scu.ac.ir [Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz (Iran, Islamic Republic of); Dehmolaei, R. [Department of Materials Science and Engineering, Faculty of Engineering, Shahid Chamran University of Ahvaz (Iran, Islamic Republic of); Amirani, A.R. [12th Ghaem Street, Bld. Hashemzadeh, Shahrak Golestan, Tehran (Iran, Islamic Republic of)

2015-02-15

Highlights: • Using friction stir processing, an effect of CNTs and CeO{sub 2} reinforcements on mechanical and corrosion properties of Al5083 alloy is reported. • The strength of Al5083 was increased by 42%, its matrix grain size reduced five times, and hardness was doubled by the incorporation of CNTs-CeO{sub 2} mixture in the volume ratio of 75-25 respectively. • Unlike the CNTs, incorporation of nanosized CeO{sub 2} particles resulted in remarkable increase in pitting resistance of the alloy. - Abstract: In the present investigation, friction stir processing (FSP) was utilized to incorporate Multi Walled Carbon Nano Tubes (MWCNT) and nanosized cerium oxide particles into the matrix of Al5083 alloy to form surface reinforced composites. The effect of these nanosized reinforcements either separately or in the combined form, on microstructural modification, mechanical properties and corrosion resistance of FSPed Al5083 surface composites was studied. A threaded cylindrical hardened steel tool was used with the rotation speeds of 600 and 800 rpm and travel speeds of 35 and 45 mm/min and a tilt angle of 5°. Mechanical properties and corrosion resistance of FSPed samples were evaluated and compared with the base alloy. The maximum tensile strength and hardness value were achieved for the hybrid composite containing a mixture of CNTs and cerium oxide in the volume ratio of 75-25, respectively, whereas a significant increase in pitting resistance of the base alloy was obtained when cerium oxide alone was incorporated. The corrosion behavior of the samples was investigated by potentiodynamic polarization tests and assessed in term of pitting potential and passivation range. Microstructural analysis carried out by using optical and electron microscopes showed that reinforcements are well dispersed inside the nugget zone (NZ), and remarkable grain refinement is gained. The study was aimed to fabricate surface composites with improved mechanical properties and

Nano Precipitation and Hardening of Die-Quenched 6061 Aluminum Alloy.

Science.gov (United States)

Utsunomiya, Hiroshi; Tada, Koki; Matsumoto, Ryo; Watanabe, Katsumi; Matsuda, Kenji

2018-03-01

Die quenching is applied to an age-hardenable aluminium alloys to obtain super-saturated solid solution. The application is advantageous because it can reduce number of manufacturing processes, and may increase strength by strain aging. If die quenching is realized in forging as well as sheet forming, it may widen industrial applicability further. In this study, Al-Mg-Si alloy AA6061 8 mm-thick billets were reduced 50% in height without cracks by die-quench forging. Supersaturated solid solution was successfully obtained. The die-quenched specimen shows higher hardness with nano precipitates at shorter aging time than the conventional water-quenched specimen.

Metal Matrix Composites Reinforced by Nano-Particles—A Review

Directory of Open Access Journals (Sweden)

Riccardo Casati

2014-03-01

Full Text Available Metal matrix composites reinforced by nano-particles are very promising materials, suitable for a large number of applications. These composites consist of a metal matrix filled with nano-particles featuring physical and mechanical properties very different from those of the matrix. The nano-particles can improve the base material in terms of wear resistance, damping properties and mechanical strength. Different kinds of metals, predominantly Al, Mg and Cu, have been employed for the production of composites reinforced by nano-ceramic particles such as carbides, nitrides, oxides as well as carbon nanotubes. The main issue of concern for the synthesis of these materials consists in the low wettability of the reinforcement phase by the molten metal, which does not allow the synthesis by conventional casting methods. Several alternative routes have been presented in literature for the production of nano-composites. This work is aimed at reviewing the most important manufacturing techniques used for the synthesis of bulk metal matrix nanocomposites. Moreover, the strengthening mechanisms responsible for the improvement of mechanical properties of nano-reinforced metal matrix composites have been reviewed and the main potential applications of this new class of materials are envisaged.

Influencia de los parámetros de la soldadura metálica fría en las aleaciones AA5083 y AA6061//Influence of the colt metal welding parameters on the AA5083 and AA6061 aluminum

Directory of Open Access Journals (Sweden)

René Eduardo de‐Luna‐Alanís

2015-01-01

Full Text Available El trabajo tuvo como objetivo evaluar la influencia de la velocidad de la soldadura y de las correcciones del arco y pulso en el proceso de Transferencia Metálica Fría sobre las propiedades mecánicas de las aleaciones AA5083 y AA6061. Se desarrolló un diseño experimental de tipo factorial multinivel, con 4 factores independientes (Corrección de Arco, Pulso, Velocidad de Soldadura y Aleación. Los parámetros fundamentales fueron: Corriente de base 250 A; Voltaje de arco 21 V y Polaridad (Direct current electrode positive, DCEP. La evaluación se realizó a través de un ensayo de tracción transversal sobre probetas planas obtenidas de los cupones soldados. Se demuestra que el modelo aplicado es adecuado, revelándose en los experimentos diferencias sustanciales en las propiedades Tensión de fluencia 29,56 %, Módulo de elasticidad 51,16 % y Trabajo específico de deformación elástica 42,30 %, el cual no posee una dependencia lineal con elresto de las propiedades anteriores.Palabras claves: transferencia metálica fría, aleación AA5083, aleación AA6061, propiedades mecánicas._______________________________________________________________________________AbstractThe work objective was to evaluatethe influence of Cold Metal Transfer process arc and pulse corrections and welding speed on the mechanical properties of AA5083 and AA6061 aluminum alloys. For it, a Factorial Multilevel experimental design whit 4 independent factor (arc correction, pulse correction, welding speed and alloy was developed. The essential welding parameters employed were: base current 250 A; arc voltage 21 V and polarity (DCEP. The evaluation was made whit a transverse traction test of plate welded coupons. The experimental model applied wasadequate and substantial differences was showed between yield tensile strength 29,56 %, elasticity module (51,16 % and specific work of elastic deformation 42,30 %, which it does not possess a lineal dependence whit the rest

Experimental investigation of hardness of FSW and TIG joints of Aluminium alloys of AA7075 and AA6061

Directory of Open Access Journals (Sweden)

Chetan Patil

2016-07-01

Full Text Available This paper reports hardness testing conducted on welded butt joints by FSW and TIG welding process on similar and dissimilar aluminium alloys. FSW joints were produced for similar alloys of AA7075T651 and dissimilar alloys of AA7075T651- AA6061T6. The Friction stir welds of AA7075 & AA6061 aluminium alloy were produced at different tool rotational speeds of 650,700, 800, 900, 1000 and transverse speed of 30, 35, 40 mm/min. TIG welding was conducted along the rolling direction of similar and dissimilar aluminium plates. The Brinell hardness testing techniques were employed to conduct the tests; these tests were conducted on the welds to ascertain the joint integrity before characterization to have an idea of the quality of the welds

Corrosion behavior of Al6061 alloy weldment produced by friction stir welding process

Directory of Open Access Journals (Sweden)

Farhad Gharavi

2015-07-01

Full Text Available In this work, the corrosion behavior of welded lap joints of AA6061-T6 aluminum alloy produced by friction stir welding process has been investigated. Corrosion properties of welded lap joints were studied by cyclic polarization and electrochemical impedance spectroscopy tests. All tests were performed in an aerated 0.6 mol L−1 NaCl aqueous solution with pH = 6.5 at a temperature of 30 °C to characterize corrosion morphology and realize corrosion features of weld regions as opposed to the parent alloy. The microstructure of weld nugget (WN, heated affected zone (HAZ, and parent alloy were analyzed using scanning electron microscopy and energy dispersive spectroscopy. The experimental results indicated that the welding process has a major effect on the corrosion resistance, which possibly associated to the break-down and dissolution of intermetallic particles. It is supposed that an increasing in intermetallic distributed throughout the matrix of weld regions increases the galvanic corrosion couples. Furthermore, by decreasing the grain size in the weld regions, the susceptibility to corrosion is enhanced. The pitting corrosion and intergranular attack are the dominant corrosion types in the weld regions and the parent alloy.

Study of microstructural evolutions of the 6061-T6 aluminium alloy under irradiation

International Nuclear Information System (INIS)

Flament, Camille

2015-01-01

The 6061-T6 Aluminium alloy, whose microstructure contains Al(Fe,Mn,Cr)Si dispersoids and hardening needle-shaped β'' precipitates (Mg, Si), has been chosen as the structural material for the core vessel of the Material Testing Jules Horowitz Nuclear Reactor. Because it will be submitted to high neutron flux at a temperature around 50 C, it is necessary to study microstructural evolutions induced by irradiation and especially the stability of the second phase particles. In this work, an analytical study by in-situ and ex-situ electron and ion irradiations has been performed, as well as a study under neutron irradiation. The precipitate characterization by Transmission Electron Microscopy demonstrates that Al(Fe,Mn,Cr)Si dispersoids are driven under irradiation towards their equilibrium configuration, consisting of a core/shell structure, enhanced by irradiation, with a (Fe, Mn) enriched core surrounded by a Cr-enriched shell. In contrast, the (Mg,Si) β'' precipitates are destabilized by irradiation. They dissolve under ion irradiation in favor of a new precipitation of (Mg,Si,Cu,Cr,Al) rich clusters resulting in an increase of the alloy's hardness. β'' precipitates tend towards a transformation to cubic precipitates under neutron irradiation. (author) [fr

Thermal and mechanical behaviour of sub micron sized fly ash reinforced polyester resin composite

Science.gov (United States)

Nantha Kumar, P.; Rajadurai, A.; Muthuramalingam, T.

2018-04-01

The utilization of particles reinforced resin matrix composites is being increased owing to its lower density and high strength to weight ratio. In the present study, an attempt has been made to synthesize fly ash particles reinforced polyester resin composite for engine cowling application. The thermal stability and mechanical behaviours such as hardness and flexural strength of the composite with 2, 3 and 4 weight % of reinforcement is studied and analyzed. The thermo gravimetric analysis indicates that the higher addition of reinforcement increases the decomposition temperature due to its refractory nature. It is also observed that the hardness increases with higher filler addition owing to the resistance of FA particles towards penetration. The flexural strength is found to increase up to the addition of 3% of FA particles, whereas the polyester resin composite prepared with 4% FA particles addition is observed to have low flexural strength owing to agglomeration of particles.

Effect of wear parameters on dry sliding behavior of Fly Ash/SiC particles reinforced AA 2024 hybrid composites

Science.gov (United States)

Bhaskar Kurapati, Vijaya; Kommineni, Ravindra

2017-09-01

In the present work AA 2024 alloy reinforced with mixtures of SiC and Fly Ash (FA) particles of 70 µm (5, 10 and 15 wt. %) are fabricated using the stir casting method. Both reinforcements are added in equal weight proportions. The wear test specimens are prepared from both the alloy and composite castings in the dimensions of Ф 4 mm and 30 mm lengths by the wire cut EDM process. The dry sliding wear properties of the prepared composites at room temperature are estimated by pin-on-disc wear testing equipment. The wear characteristics of the composites are studied by conducting the dry sliding wear test over loads of 0.5 Kgf, 1.0 Kgf, 1.5 Kgf, a track diameter of 60 mm and sliding times of 15 min, 30 min, 45min. The experimental results shows that the wear decreases with an increase in the weight percentage of FA and SiC particles in the matrix. Additionally wear increases with an increase in load and sliding time. Further, it is found that the wear resistance of the AA2024-Hybrid composites is higher than that of the AA2024 matrix.

Ability of paramedics to perform endotracheal intubation during continuous chest compressions: a randomized cadaver study comparing Pentax AWS and Macintosh laryngoscopes.

Science.gov (United States)

Truszewski, Zenon; Czyzewski, Lukasz; Smereka, Jacek; Krajewski, Paweł; Fudalej, Marcin; Madziala, Marcin; Szarpak, Lukasz

2016-09-01

The aim of the trial was to compare the time parameters for intubation with the use of the Macintosh (MAC) laryngoscope and Pentax AWS-S100 videolaryngoscope (AWS; Pentax Corporation, Tokyo, Japan) with and without chest compression (CC) by paramedics during simulated cardiopulmonary resuscitation in a cadaver model. This was a randomized crossover cadaver trial. Thirty-five paramedics with no experience in videolaryngoscopy participated in the study. They performed intubation in two emergency scenarios: scenario A, normal airway without CC; scenario B, normal airway with continuous CC. The median time to first ventilation with the use of the AWS and the MAC was similar in scenario A: 25 (IQR, 22-27) seconds vs. 24 (IQR, 22.5-26) seconds (P=.072). A statistically significant difference in TTFV between AWS and MAC was noticed in scenario B (P=.011). In scenario A, the first endotracheal intubation (ETI) attempt success rate was achieved in 97.1% with AWS compared with 94.3% with MAC (P=.43). In scenario B, the success rate after the first ETI attempt with the use of the different intubation methods varied and amounted to 88.6% vs. 77.1% for AWS and MAC, respectively (P=.002). The Pentax AWS offered a superior glottic view as compared with the MAC laryngoscope, which was associated with a higher intubation rate and a shorter intubation time during an uninterrupted CC scenario. However, in the scenario without CC, the results for AWS and MAC were comparable. Copyright © 2016 Elsevier Inc. All rights reserved.

Effects of heat treatments on the microstructure and mechanical properties of a 6061 aluminium alloy

International Nuclear Information System (INIS)

Maisonnette, D.; Suery, M.; Nelias, D.; Chaudet, P.; Epicier, T.

2011-01-01

Research highlights: → Description of the mechanical behavior of AA6061-T6 at RT after various thermal histories. → A fast-heating device has been designed to reproduce those thermal histories on tensile specimens. → The thermal loadings are representative of the temperature change observed in the HAZ during welding. → The variation of mechanical properties is the result of metallurgical evolution observed by TEM. → The yield stress at RT decreases with the maximum temperature reached during the thermal cycle. - Abstract: This paper describes the mechanical behavior of the 6061-T6 aluminium alloy at room temperature for various previous thermal histories representative of an electron beam welding. A fast-heating device has been designed to control and apply thermal loadings on tensile specimens. Tensile tests show that the yield stress at ambient temperature decreases if the maximum temperature reached increases or if the heating rate decreases. This variation of the mechanical properties is the result of microstructural changes which have been observed by Transmission Electron Microscopy (TEM).

High strength Al–Al2O3p composites: Optimization of extrusion parameters

DEFF Research Database (Denmark)

Luan, B.F.; Hansen, Niels; Godfrey, A.

2011-01-01

Composite aluminium alloys reinforced with Al2O3p particles have been produced by squeeze casting followed by hot extrusion and a precipitation hardening treatment. Good mechanical properties can be achieved, and in this paper we describe an optimization of the key processing parameters...... on an investigation of their mechanical properties and microstructure, as well as on the surface quality of the extruded samples. The evaluation shows that material with good strength, though with limited ductility, can be reliably obtained using a production route of squeeze casting, followed by hot extrusion....... The parameters investigated are the extrusion temperature, the extrusion rate and the extrusion ratio. The materials chosen are AA 2024 and AA 6061, each reinforced with 30vol.% Al2O3 particles of diameter typically in the range from 0.15 to 0.3μm. The extruded composites have been evaluated based...

Pengaruh Bauran Pemasaran (Marketing Mix) Dan Kualitas Pelayanan Terhadap Kepuasan Pelanggan di A&W Restaurants di Sun Plaza Medan

OpenAIRE

Purba, Aurora Tianisari

2012-01-01

A&W Restaurants Sun Plaza Medan is one of the company engaged in the fast food (fast food), which the company must implement appropriate marketing strategies to achieve corporate objectives and service are also very necessary to provide and create customer satisfaction at the A&W Restaurants well across Indonesia especially in Medan, North Sumatra. Competition experienced by the fast food company A&W Restaurants in Indonesia is quite tight, given the many fast food company such as Kentucky Fr...

2-Local derivations on matrix algebras over semi-prime Banach algebras and on AW*-algebras

International Nuclear Information System (INIS)

Ayupov, Shavkat; Kudaybergenov, Karimbergen

2016-01-01

The paper is devoted to 2-local derivations on matrix algebras over unital semi-prime Banach algebras. For a unital semi-prime Banach algebra A with the inner derivation property we prove that any 2-local derivation on the algebra M 2 n (A), n ≥ 2, is a derivation. We apply this result to AW*-algebras and show that any 2-local derivation on an arbitrary AW*-algebra is a derivation. (paper)

Mesoscale Characterization of Fracture Properties of Steel Fiber-Reinforced Concrete Using a Lattice–Particle Model

Directory of Open Access Journals (Sweden)

Francisco Montero-Chacón

2017-02-01

Full Text Available This work presents a lattice–particle model for the analysis of steel fiber-reinforced concrete (SFRC. In this approach, fibers are explicitly modeled and connected to the concrete matrix lattice via interface elements. The interface behavior was calibrated by means of pullout tests and a range for the bond properties is proposed. The model was validated with analytical and experimental results under uniaxial tension and compression, demonstrating the ability of the model to correctly describe the effect of fiber volume fraction and distribution on fracture properties of SFRC. The lattice–particle model was integrated into a hierarchical homogenization-based scheme in which macroscopic material parameters are obtained from mesoscale simulations. Moreover, a representative volume element (RVE analysis was carried out and the results shows that such an RVE does exist in the post-peak regime and until localization takes place. Finally, the multiscale upscaling strategy was successfully validated with three-point bending tests.

Mesoscale Characterization of Fracture Properties of Steel Fiber-Reinforced Concrete Using a Lattice-Particle Model.

Science.gov (United States)

Montero-Chacón, Francisco; Cifuentes, Héctor; Medina, Fernando

2017-02-21

This work presents a lattice-particle model for the analysis of steel fiber-reinforced concrete (SFRC). In this approach, fibers are explicitly modeled and connected to the concrete matrix lattice via interface elements. The interface behavior was calibrated by means of pullout tests and a range for the bond properties is proposed. The model was validated with analytical and experimental results under uniaxial tension and compression, demonstrating the ability of the model to correctly describe the effect of fiber volume fraction and distribution on fracture properties of SFRC. The lattice-particle model was integrated into a hierarchical homogenization-based scheme in which macroscopic material parameters are obtained from mesoscale simulations. Moreover, a representative volume element (RVE) analysis was carried out and the results shows that such an RVE does exist in the post-peak regime and until localization takes place. Finally, the multiscale upscaling strategy was successfully validated with three-point bending tests.

Mesoscale Characterization of Fracture Properties of Steel Fiber-Reinforced Concrete Using a Lattice–Particle Model

Science.gov (United States)

Montero-Chacón, Francisco; Cifuentes, Héctor; Medina, Fernando

2017-01-01

This work presents a lattice–particle model for the analysis of steel fiber-reinforced concrete (SFRC). In this approach, fibers are explicitly modeled and connected to the concrete matrix lattice via interface elements. The interface behavior was calibrated by means of pullout tests and a range for the bond properties is proposed. The model was validated with analytical and experimental results under uniaxial tension and compression, demonstrating the ability of the model to correctly describe the effect of fiber volume fraction and distribution on fracture properties of SFRC. The lattice–particle model was integrated into a hierarchical homogenization-based scheme in which macroscopic material parameters are obtained from mesoscale simulations. Moreover, a representative volume element (RVE) analysis was carried out and the results shows that such an RVE does exist in the post-peak regime and until localization takes place. Finally, the multiscale upscaling strategy was successfully validated with three-point bending tests. PMID:28772568

Influence of the Sr and Mg Alloying Additions on the Bonding Between Matrix and Reinforcing Particles in the AlSi7Mg/SiC-Cg Hybrid Composite

Directory of Open Access Journals (Sweden)

Dolata A. J.

2016-06-01

Full Text Available The aim of the work was to perform adequate selection of the phase composition of the composite designated for permanent - mould casting air compressor pistons. The hybrid composites based on AlSi7Mg matrix alloy reinforced with mixture of silicon carbide (SiC and glassy carbon (Cg particles were fabricated by the stir casting method. It has been shown that the proper selection of chemical composition of matrix alloy and its modification by used magnesium and strontium additions gives possibility to obtain both the advantageous casting properties of composite suspensions as well as good bonding between particles reinforcements and matrix.

Interface analysis of A1 matrix composites produced by hot isostatic pressing, squeeze casting and semi-solid processing

International Nuclear Information System (INIS)

Shamsul, J.B.; Zainal Arifin Ahmad; Faaizulaswad, M.S.; Azmi, R.

2000-01-01

The interface analysis has been carried out an aluminium based composites system produced by hot isostatic pressing, squeeze casting and semi-solid processing. A range of different fabrication techniques has been used to produce different types of microstructure of Al 2124 (Al-Cu-Mg) reinforced with 5 weight % SiC particles. Blending followed by hot isostatic pressing is used to fabricate composite I. Composite II was 6061 (Al-Si-Mg) wrought aluminium alloy reinforced with fibres of alumina-silica (V f = 0.58) and fabricated by squeeze casting. Finally, A356 (AlSi7Mg0.3) alloy was reinforced with 20 Vol.% of SiC particles (13 μm) and namely as composite III. Composite III is fabricated by semi-solid processing. Interface analysis was done by optical microscopy, scanning and transmission electron microscopy. Composite I exhibited good interface bonding and dislocation was also observed near the interface. Elements such as Al, Fe, Cr, Mn were found near the interface of composite II and intermetallic of iron rich inclusion and Mg 2 Si were observed near the interface of composite III. (Author)

Microstructural characteristics and mechanical properties of carbon nanotube reinforced aluminum alloy composites produced by ball milling

International Nuclear Information System (INIS)

Raviathul Basariya, M.; Srivastava, V.C.; Mukhopadhyay, N.K.

2014-01-01

Highlights: • 6082 Al alloy composite with 2 wt% multiwalled carbon nanotubes prepared by milling. • Effect of milling time on structure and property evolution has been studied. • The reinforced composite powders showed a drastic crystallite size refinement. • The presence of carbon nanotube led to a two fold increase in the hardness and modulus. • The composite powder showed good thermal stability studied by DTA. - Abstract: The influence of milling time on the structure, morphology and thermal stability of multi-walled carbon nanotubes (MWCNTs) reinforced EN AW6082 aluminum alloy powders has been studied. After structural and microstructural characterization of the mechanically milled powders micro- and nano-hardness of the composite powder particles were evaluated. The morphological and X-ray diffraction studies on the milled powders revealed that the carbon nanotubes (CNTs) were uniformly distributed and embedded within the aluminum matrix. No reaction products were detected even after long milling up to 50 h. Nanotubes became shorter in length as they fractured under the impact and shearing action during the milling process. A high hardness of about 436 ± 52 HV is achieved for the milled powders, due to the addition of MWCNTs, after milling for 50 h. The increased elastic modulus and nanohardness can be attributed to the finer grain size evolved during high energy ball milling and to the uniform distribution of hard CNTs in the Al-alloy matrix. The hardness values of the composite as well as the matrix alloy compares well with that predicted by the Hall–Petch relationship

75 FR 70739 - Domtar A.W. LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for...

Science.gov (United States)

2010-11-18

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER11-2021-000] Domtar A.W. LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for Blanket Section... of Domtar A.W. LLC's application for market-based rate authority, with an accompanying rate tariff...

75 FR 70738 - Domtar A.W. LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for...

Science.gov (United States)

2010-11-18

... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. ER11-2021-000] Domtar A.W. LLC; Supplemental Notice That Initial Market-Based Rate Filing Includes Request for Blanket Section... of Domtar A.W. LLC's application for market-based rate authority, with an accompanying rate tariff...

Mechanical properties of aluminium matrix composites reinforced with intermetallics

International Nuclear Information System (INIS)

Torres, B.; Garcia-Escorial, A.; Ibanez, J.; Lieblich, M.

2001-01-01

In this work 2124 aluminium matrix composites reinforced with Ni 3 Al, NiAl, MoSi 2 and Cr 3 Si intermetallic powder particles have been investigated. For comparison purposes, un reinforced 2124 and reinforced with SiC have also been studied. In all cases, the same powder metallurgy route was used, i. e. the 2124 alloy was obtained by rapid solidification and the intermetallic particles by self-propagating high-temperature synthesis (SHS). The matrix and the intermetallics were mechanically blended, cold compacted and finally hot extruded. Tensile tests were carried out in T1 and T4 treatments. Results indicate that mechanical properties depend strongly on the tendency to form new phases at the matrix-intermetallic interface during processing and/or further thermal treatments. The materials which present better properties are those that present less reaction between matrix and intermetallic reinforcement, i. e. MoSi 2 and SiC reinforced composites. (Author) 9 refs

A Brief Research Review for Improvement Methods the Wettability between Ceramic Reinforcement Particulate and Aluminium Matrix Composites

Science.gov (United States)

Razzaq, Alaa Mohammed; Majid, Dayang Laila Abang Abdul; Ishak, M. R.; B, Uday M.

2017-05-01

The development of new methods for addition fine ceramic powders to Al aluminium alloy melts, which would lead to more uniform distribution and effective incorporation of the reinforcement particles into the aluminium matrix alloy. Recently the materials engineering research has moved to composite materials from monolithic, adapting to the global need for lightweight, low cost, quality, and high performance advanced materials. Among the different methods, stir casting is one of the simplest ways of making aluminium matrix composites. However, it suffers from poor distribution and combination of the reinforcement ceramic particles in the metal matrix. These problems become significantly effect to reduce reinforcement size, more agglomeration and tendency with less wettability for the ceramic particles in the melt process. Many researchers have carried out different studies on the wettability between the metal matrix and dispersion phase, which includes added wettability agents, fluxes, preheating the reinforcement particles, coating the reinforcement particles, and use composting techniques. The enhancement of wettability of ceramic particles by the molten matrix alloy and the reinforcement particles distribution improvement in the solidified matrix is the main objective for many studies that will be discussed in this paper.

The Influence of Pressure Die Casting Parameters on Distribution of Reinforcing Particles in the AlSi11/10% SiC Composite

Directory of Open Access Journals (Sweden)

Pasieka A.

2013-09-01

Full Text Available The method of pressure die casting of composites with AlSi11 alloy matrix reinforced with 10 vol. % of SiC particles and the analysis of the distribution of particles within the matrix is presented. The composite castings were produced at various values of the piston velocity in the second stage of injection, at diverse intensification pressure values, and various injection gate width values. The distribution of particles over the entire cross-section of the tensile specimen is shown. The index of distribution was determined on the basis of particle count in elementary measuring fields. The regression equation describing the change of the considered index was found as a function of the pressure die casting parameters. The conclusion presents an analysis of the obtained results and their interpretation.

Effect of re-melting on particle distribution and interface formation in SiC reinforced 2124Al matrix composite

Energy Technology Data Exchange (ETDEWEB)

Mandal, Durbadal, E-mail: durbadal73@yahoo.co.in [MEF Division, CSIR-National Metallurgical Laboratory, Jamshedpur 831007 (India); Viswanathan, Srinath [Dept of Metallurgical and Materials Engineering, University of Alabama, Tuscaloosa, AL (United States)

2013-12-15

The interface between metal matrix and ceramic reinforcement particles plays an important role in improving properties of the metal matrix composites. Hence, it is important to find out the interface structure of composite after re-melting. In the present investigation, the 2124Al matrix with 10 wt.% SiC particle reinforced composite was re-melted at 800 °C and 900 °C for 10 min followed by pouring into a permanent mould. The microstructures reveal that the SiC particles are distributed throughout the Al-matrix. The volume fraction of SiC particles varies from top to bottom of the composite plate and the difference increases with the decrease of re-melting temperature. The interfacial structure of re-melted 2124Al–10 wt.%SiC composite was investigated using scanning electron microscopy, an electron probe micro-analyzer, a scanning transmission electron detector fitted with scanning electron microscopy and an X-ray energy dispersive spectrometer. It is found that a thick layer of reaction product is formed at the interface of composite after re-melting. The experimental results show that the reaction products at the interface are associated with high concentration of Cu, Mg, Si and C. At re-melting temperature, liquid Al reacts with SiC to form Al{sub 4}C{sub 3} and Al–Si eutectic phase or elemental Si at the interface. High concentration of Si at the interface indicates that SiC is dissociated during re-melting. The X-ray energy dispersive spectrometer analyses confirm that Mg- and Cu-enrich phases are formed at the interface region. The Mg is segregated at the interface region and formed MgAl{sub 2}O{sub 4} in the presence of oxygen. The several elements identified at the interface region indicate that different types of interfaces are formed in between Al matrix and SiC particles. The Al–Si eutectic phase is formed around SiC particles during re-melting which restricts the SiC dissolution. - Highlights: • Re-melted composite shows homogeneous particle

Microstructural study and densification analysis of hot work tool steel matrix composites reinforced with TiB{sub 2} particles

Energy Technology Data Exchange (ETDEWEB)

Fedrizzi, A., E-mail: anna.fedrizzi@ing.unitn.it [Department of Industrial Engineering, University of Trento, Via Mesiano 77, 38123 Trento (Italy); Pellizzari, M. [Department of Industrial Engineering, University of Trento, Via Mesiano 77, 38123 Trento (Italy); Zadra, M. [K4Sint, Start-up of the University of Trento, Viale Dante 300, 38057 Pergine Valsugana (Italy); Marin, E. [Department of Chemistry, Physics and Environment, University of Udine, Via Cotonificio 108, 33100 Udine (Italy)

2013-12-15

Hot work tool steels are characterized by good toughness and high hot hardness but are less wear resistant than other tooling materials, such as high speed steel. Metal matrix composites show improved tribological behavior, but not much work has been done in the field of hot work tool steels. In this paper TiB{sub 2}-reinforced hot work tool steel matrix composites were produced by spark plasma sintering (SPS). Mechanical alloying (MA) was proposed as a suited process to improve the composite microstructure. Density measurements and microstructure confirmed that MA promotes sintering and produces a fine and homogeneous dispersion of reinforcing particles. X-ray diffraction patterns of the sintered composites highlighted the formation of equilibrium Fe{sub 2}B and TiC, as predicted by thermodynamic calculations using Thermo-Calc® software. Scanning electron microscopy as well as scanning Kelvin probe force microscopy highlighted the reaction of the steel matrix with TiB{sub 2} particles, showing the formation of a reaction layer at the TiB{sub 2}-steel interface. Phase investigations pointed out that TiB{sub 2} is not chemically stable in steel matrix because of the presence of carbon even during short time SPS. - Highlights: • TiB{sub 2} reinforced steel matrix composites were produced by spark plasma sintering. • TiB{sub 2} was successfully dispersed in the steel matrix by mechanical alloying. • Steel and TiB{sub 2} react during sintering forming equilibrium Fe{sub 2}B and TiC. • The new phases were investigated by means of AFM, Volta potential and XRD analyses.

Guided Multiple Launch Rocket System/Guided Multiple Launch Rocket System Alternative Warhead (GMLRS/GMLRS AW)

Science.gov (United States)

2015-12-01

Physical Configuration Audit for the GMLRS AW was completed at the system level in March 2015. ​Director of Operational Test and Evaluation Assessment...Confidence Level Confidence Level of cost estimate for current APB: 50% The confidence level used in establishing the cost estimate for GMLRS/GMLRS AW...PAUC Development Estimate Changes PAUC Production Estimate Econ Qty Sch Eng Est Oth Spt Total 0.039 -0.003 0.001 0.001 0.009 0.037 0.000 0.000 0.045

Blood Compatibility of ZrO2 Particle Reinforced PEEK Coatings on Ti6Al4V Substrates

Directory of Open Access Journals (Sweden)

Jian Song

2017-11-01

Full Text Available Titanium (Ti and its alloys are widely used in biomedical devices. As biomaterials, the blood compatibility of Ti and its alloys is important and needs to be further improved to provide better functionality. In this work, we studied the suitability of zirconia (ZrO2 particle reinforced poly-ether-ether-ketone (PEEK coatings on Ti6Al4V substrates for blood-contacting implants. The wettability, surface roughness and elastic modulus of the coatings were examined. Blood compatibility tests were conducted by erythrocytes observation, hemolysis assay and clotting time of recalcified human plasma, to find out correlations between the microstructure of the ZrO2-filled PEEK composite coatings and their blood compatibilities. The results suggested that adding ZrO2 nanoparticles increased the surface roughness and improved the wettability and Derjaguin-Muller-Toporov (DMT elastic modulus of PEEK coating. The PEEK composite matrix coated Ti6Al4V specimens did not cause any aggregation of erythrocytes, showing morphological normal shapes. The hemolysis rate (HR values of the tested specimens were much less than 5% according to ISO 10993-4 standard. The values of plasma recalcification time (PRT of the tested specimens varied with the increasing amount of ZrO2 nanoparticles. Based on the results obtained, 10 wt % ZrO2 particle reinforced PEEK coating has demonstrated an optimum blood compatibility, and can be considered as a candidate to improve the performance of existing PEEK based coatings on titanium substrates.

Friction welding of A 6061 aluminum alloy and S45C carbon steel

Energy Technology Data Exchange (ETDEWEB)

Shinoda, T. [Nagoya Univ., Furo-cho, Chikusa-ku, Nagoya (Japan); Kawata, S. [Post Graduate Student, Nagoya Univ., Nagoya (Japan)

2004-07-01

Many researches for friction welding of aluminum with either carbon steel or stainless steel have been carried out. From those results, it is concluded that the greatest problem is the formation of brittle intermetallic compounds at weld interface. However, it is not clearly demonstrated the effect of friction welding parameters on the formation of intermetallic compounds. This research purposes are to evaluate the formation of intermetallic compounds and to investigate the effect of friction welding parameters on the strength of welded joint. For these purposes, A6061 aluminum alloy and S45C carbon steel were used with a continuous drive vertical friction welding machine. Tensile test results revealed that the maximum tensile strength was achieved at extremely short friction time and high upset. The joint strength reached 92% of the tensile strength of A6061 base metal. Tensile strength of friction welding was increasing with increasing upset pressure when friction time 1sec. However, tensile properties were deteriorated with increasing friction time. It was observed that the amount of formed intermetallic compound was increasing with increasing friction time at weld interface. Partly formed intermetallic compound on weld interface were identified when friction time 1 sec. However, intermetallic compound layer were severely developed with longer friction time at weld interface. It was concluded that intermetallic compound layer deteriorated the tensile properties of weld joints. (orig.)

Properties of copper matrix reinforced with nano- and micro-sized Al2O3 particles

International Nuclear Information System (INIS)

Rajkovic, Viseslava; Bozic, Dusan; Jovanovic, Milan T.

2008-01-01

The mixture of electrolytic copper powder with 5 wt.% of commercial Al 2 O 3 powder (average particle size: 15 and 0.75 μm, respectively) and the inert gas atomized prealloyed copper powder (average particle size: 30 μm) containing 2.5 wt.% aluminum were separately milled in air up to 20 h in the planetary ball mill. During milling aluminum in the prealloyed copper powders was oxidized in situ by internal oxidation with oxygen from the air forming very fine nano-sized Al 2 O 3 particles. The internal oxidation of 2.5 wt.% aluminum generated 4.7 wt.% of Al 2 O 3 in the copper matrix. Powders and compacts were characterized by light and scanning electron microscopy (SEM), electron probe microanalysis (EPMA) and X-ray diffraction analysis. Microhardness and electrical conductivity were also included in measurements. The microhardness of Cu-2.5 wt.% Al compacts was 3.6 times higher than that of compacts processed from electrolytic copper powder. This increase in microhardness is a consequence of a fine dispersion of Al 2 O 3 particles and refined grain structure. The average values of electrical conductivity of compacts processed from Cu-5 wt.% Al 2 O 3 and Cu-2.5 wt.% Al powders previously milled for 20 h and were 88% and 70% IACS, respectively, which is a rather significant increase if compared with values of 60% and 23% IACS of compacts processed from as-received and non-milled powders. The microhardness of 20-h milled compacts decreases with the heat treatment at 800 deg. C. Due to the effect of nano-sized Al 2 O 3 particles Cu-2.5 wt.% Al compacts show lower decrease in microhardness. The results are discussed in terms of the effect of Al 2 O 3 particle size and fine grain structure on the reinforcing of the copper matrix

Effects of high thermal neutron fluences on Type 6061 aluminum

International Nuclear Information System (INIS)

Weeks, J.R.; Czajkowski, C.J.; Farrell, K.

1992-01-01

The control rod drive follower tubes of the High Flux Beam Reactor are contructed from precipitation-hardened 6061-T6 aluminum alloy and they operate in the high thermal neutron flux regions of the core. It is shown that large thermal neutron fluences up to ∼4 x 10 23 n/cm 2 at 333K cause large increases in tensile strength and relatively modest decreases in tensile elongation while significantly reducing the notch impact toughness at room temperature. These changes are attributed to the development of a fine distribution of precipitates of amorphous silicon of which about 8% is produced radiogenically. A proposed role of thermal-to-fast flux ratio is discussed

ELABORATION OF AN EPOXY COATING REINFORCED WITH ZIRCONIUM CARBIDE NANOSTRUCTURES

Directory of Open Access Journals (Sweden)

Lucia G. Díaz-Barriga

2013-12-01

Full Text Available This work shows the preparation of a transparent epoxy coating reinforced with 200 PPM of zirconium carbide nanostructures. The nanostructures of ZrC were prepared by mechanosynthesis. The additive characteristics analyzed by X-ray diffraction (XRD and scanning electron microscopy (SEM were presented. Epoxy coating adhesion on a steel plate was analyzed using MEB. Thermogravimetric analysis (TGA was performed to the reinforced paints between 20-700 °C. The reinforced enamel was compared with an enamel without nanostructures. There is not vaporization of reinforced enamel at a 95 y 100 °C with ZrC particles size of 10 µm y 120 nm respectively. The final enamel degradation is slower when there is a 14% by weight of the residue and 426 °C with 120nm diameter particles.

Automatic Weather Station (AWS Program operated by the University of Wisconsin-Madison during the 2012-2013 field season: Challenges and Successes

Directory of Open Access Journals (Sweden)

Matthew A. Lazzara

2015-03-01

Full Text Available This report reviews 2012-2013 field season activities of the University of Wisconsin-Madison＇s Antarctic Automatic Weather Station (AWS program, summarizes the science that these sites are supporting, and outlines the factors that impact the number of AWS sites serviced in any given field season. The 2012-2013 austral summer season was unusual in the AWS network history. Challenges encountered include, but are not limited to, warmer than normal conditions in the Ross Island area impacting airfield operations, changes to logistical procedures, and competition for shared resources. A flexible work plan provides the best means for taking on these challenges while maximizing AWS servicing efforts under restricted conditions and meeting the need for routine servicing that maintaining an autonomous observing network demands.

Costs of Urbanisation in Poland, Based on the Example of Wrocław

Science.gov (United States)

Hełdak, Maria; Płuciennik, Monika

2017-10-01

The paper deals with the issue of charging communes with the costs of realisation of the provisions contained in local spatial development plans. When such local spatial development plan enters into force, it leads to economic consequences. In Poland, these consequences are specified in the forecast of the financial impact, which contains a prognosis of own revenues as well as of costs incurred by the budget of the commune. The research consisted in the analysis of the costs of urbanisation of land located in Wrocław, in the southern part of the Krzyki district (Poland). This area is undeveloped to a major extent, consisting mainly of agricultural land, and its development requires the construction of technological and social infrastructure facilities. The expected costs of the realisation of local spatial development plans that are binding for the southern part of Wrocław demonstrate significant costs of the construction of sewage network and municipal roads. The planned development of residential districts is not supported by the existing infrastructure. Additionally, the development of new areas will require the city of Wrocław to take over the real properties on which public goals are planned to be realised. The estimated costs of land acquisition for the realisation of public goals amount to EUR 3 728 500.

The effect of alternative work schedules (AWS) on performance during acquisition based testing at the U.S. Army Aberdeen Test Center

OpenAIRE

Thomas, Alicia J.

2014-01-01

Approved for public release; distribution is unlimited This project analyzed the effects of an alternate work schedule (AWS) on the performance of acquisition based testing conducted at the U.S. Army Aberdeen Test Center (ATC), a subordinate test center to the U.S. Army Test and Evaluation Command. The literature review uncovered how an AWS improved employee work and life balance and performance at three separate external companies. Other potential AWS success factors such as employee abse...

Strength and thermal stability of fiber reinforced plastic composites ...

African Journals Online (AJOL)

Therefore, the strength properties and thermal stability of plastic composites reinforced with rattan fibers were investigated in this work. Particles of rattan species (Eremospatha macrocarpa (EM) and Laccosperma secundiflorum (LS)) were blended with High-Density Polyethylene (HDPE) to produce fiber reinforced plastic ...

Corrosion Behavior of Arc Weld and Friction Stir Weld in Al 6061-T6 Alloys

International Nuclear Information System (INIS)

Yoon, Byoung Hyun; Kim, Heung Ju; Chang, Woong Seong; Kweon, Young Gak

2006-01-01

For the evaluation of corrosion resistance of Al 6061-T6 Alloy, Tafel method and immersion test was performed with Friction Stir Weld(FSW) and Gas Metal Arc Weld(GMAW). The Tafel and immersion test results indicated that GMA weld was severely attacked compared with those of friction stir weld. It may be mainly due to the galvanic corrosion mechanism act on the GMA weld

SYNTHESIS AND CHARACTERIZATION OF CANNABIS INDICA FIBER REINFORCED COMPOSITES

Directory of Open Access Journals (Sweden)

Amar Singh Singha

2011-04-01

Full Text Available This paper reports on the synthesis of Cannabis indica fiber-reinforced composites using Urea-Resorcinol-Formaldehyde (URF as a novel matrix through compression molding technique. The polycondensation between urea, resorcinol, and formaldehyde in different molar ratios was applied to the synthesis of the URF polymer matrix. A thermosetting matrix based composite, reinforced with lignocellulose from Cannabis indica with different fiber loadings 10, 20, 30, 40, and 50% by weight, was obtained. The mechanical properties of randomly oriented intimately mixed fiber particle reinforced composites were determined. Effects of fiber loadings on mechanical properties such as tensile, compressive, flexural strength, and wear resistance were evaluated. Results showed that mechanical properties of URF resin matrix increased considerably when reinforced with particles of Cannabis indica fiber. Thermal (TGA/DTA/DTG and morphological studies (SEM of the resin, fiber and polymer composite thus synthesized were carried out.

Corrosion fatigue performance in simulated sea water of aluminium 6061-T651 welded using ER4043 filler wire

CSIR Research Space (South Africa)

Mutombo, K

2010-10-01

Full Text Available The fatigue life of Al6061-T651 for various applied stress amplitudes in the unwelded and welded conditions was significantly lower in 3.5% NaCl simulated sea water solution, compared to that in air. The damage ratio increased with a decrease...

Microstructure, mechanical properties and texture of an AA6061/AA5754 composite fabricated by cross accumulative roll bonding

Energy Technology Data Exchange (ETDEWEB)

Verstraete, K., E-mail: kevin.verstraete@u-psud.fr [Université Paris-Sud, SP2M, ICMMO, UMR CNRS 8182, 91405 Orsay Cedex (France); Helbert, A.L. [Université Paris-Sud, SP2M, ICMMO, UMR CNRS 8182, 91405 Orsay Cedex (France); Brisset, F. [Université Paris-Sud, ICMMO, UMR CNRS 8182, 91405 Orsay Cedex (France); Benoit, A.; Paillard, P. [Institut des Matériaux Jean Rouxel (IMN), UMR 6502, Polytech’Nantes, Nantes Cedex (France); Baudin, T. [Université Paris-Sud, SP2M, ICMMO, UMR CNRS 8182, 91405 Orsay Cedex (France)

2015-07-29

AA6061 alloy is a widely used material in the automotive and aerospace industries, but is prone to hot cracking, which limits its weldability. To prevent this phenomenon, the AA6061/AA5754 composite was formed using a severe plastic deformation technique, Cross Accumulative Roll Bonding (CARB), at an elevated temperature (350 °C) to ensure good bonding between layers. This technique was efficient to maintain a small grain size, even under the process temperature conditions, and consequently, preserve good mechanical properties. The composite had better mechanical properties than the initial aluminium alloys. Microstructure and texture remained stable after two cycles and yield stress tended towards an equal value in the rolling and the transverse directions. After two cycles, the main component was the {001}〈110〉 rotated Cube, which was maintained for up to 10 cycles. Diffusion was more effective as the strain increased. Finally, a tungsten inert gas (TIG) welding process was performed on the composite and confirmed resistance to hot cracking.

Structural analysis of color video camera installation on tank 241AW101 (2 Volumes)

Energy Technology Data Exchange (ETDEWEB)

Strehlow, J.P.

1994-08-24

A video camera is planned to be installed on the radioactive storage tank 241AW101 at the DOE` s Hanford Site in Richland, Washington. The camera will occupy the 20 inch port of the Multiport Flange riser which is to be installed on riser 5B of the 241AW101 (3,5,10). The objective of the project reported herein was to perform a seismic analysis and evaluation of the structural components of the camera for a postulated Design Basis Earthquake (DBE) per the reference Structural Design Specification (SDS) document (6). The detail of supporting engineering calculations is documented in URS/Blume Calculation No. 66481-01-CA-03 (1).

Structural analysis of color video camera installation on tank 241AW101 (2 Volumes)

International Nuclear Information System (INIS)

Strehlow, J.P.

1994-01-01

A video camera is planned to be installed on the radioactive storage tank 241AW101 at the DOE' s Hanford Site in Richland, Washington. The camera will occupy the 20 inch port of the Multiport Flange riser which is to be installed on riser 5B of the 241AW101 (3,5,10). The objective of the project reported herein was to perform a seismic analysis and evaluation of the structural components of the camera for a postulated Design Basis Earthquake (DBE) per the reference Structural Design Specification (SDS) document (6). The detail of supporting engineering calculations is documented in URS/Blume Calculation No. 66481-01-CA-03 (1)

Tank characterization report for double-shell tank 241-AW-105

International Nuclear Information System (INIS)

Sasaki, L.M.

1997-01-01

One of the major functions of the Tank Waste Remediation System (TWRS) is to characterize wastes in support of waste management and disposal activities at the Hanford Site. Analytical data from sampling and analysis, along with other available information about a tank, are compiled and maintained in a tank characterization report (TCR). This report and its appendices serve as the TCR for double-shell tank 241-AW-105. The objectives of this report are to use characterization data in response to technical issues associated with tank 241-AW-105 waste; and to provide a standard characterization of this waste in terms of a best-basis inventory estimate. The response to technical issues is summarized in Section 2.0, and the best-basis inventory estimate is presented in Section 3.0. Recommendations regarding safety status and additional sampling needs are provided in Section 4.0. Supporting data and information are contained in the appendices. This report supports the requirements of the Hanford Federal Facility Agreement and Consent Order milestone Characterization. information presented in this report originated from sample analyses and known historical sources. While only the results of a recent sampling event will be used to fulfill the requirements of the data quality objectives (DQOs), other information can be used to support or question conclusions derived from these results. Historical information for tank 241-AW-105 is provided in Appendix A, including surveillance information, records pertaining to waste transfers and tank operations, and expected tank contents derived from a process knowledge model. The recent sampling event listed, as well as pertinent sample data obtained before 1996, are summarized in Appendix B along with the sampling results. The results of the 1996 grab sampling event satisfied the data requirements specified in the sampling and analysis plan (SAP) for this tank. In addition, the tank headspace flammability was measured, which addresses

THE LONG-LIVED UV ''PLATEAU'' OF SN 2012aw

Energy Technology Data Exchange (ETDEWEB)

Bayless, Amanda J.; Roming, Peter W. A. [Southwest Research Institute, Department of Space Science, 6220 Culebra Road, San Antonio, TX 78238 (United States); Pritchard, Tyler A. [Department of Astronomy and Astrophysics, Penn State University, 525 Davey Lab, University Park, PA 16802 (United States); Kuin, Paul [Mullard Space Science Laboratory, Holmbury St. Mary, Dorking, Surrey RH5 6NT (United Kingdom); Brown, Peter J. [Texas A and M University, Department of Physics and Astronomy, College Station, TX 77843-4242 (United States); Botticella, Maria Teresa; Dall' Ora, Massimo [INAF-Osservatorio Astronomico di Capodimonte, via Moiariello 16, I-80131 Napoli (Italy); Frey, Lucille H.; Even, Wesley; Fryer, Chris L. [Los Alamos National Laboratory, Los Alamos, NM 87545 (United States); Maund, Justyn R.; Fraser, Morgan [Astrophysics Research Center, School of Mathematics and Physics, Queen' s University Belfast, Belfast BT7 1NN (United Kingdom)

2013-02-10

Observations with the Swift UV Optical Telescope have unambiguously uncovered for the first time a long-lived, UV ''plateau'' in a Type II-P supernova (SN). Although this flattening in slope is hinted at in a few other SNe, due to its proximity and minimal line-of-sight extinction, SN 2012aw has afforded the first opportunity to clearly observe this UV plateau. The observations of SN 2012aw revealed all Swift UV and u-band light curves initially declined rapidly, but 27 days after the explosion the light curves flattened. Some possible sources of the UV plateau are the same thermal process that causes the optical plateau, heating from radioactive decay, or a combination of both processes.

Wear Characteristics of Hybrid Composites Based on Za27 Alloy Reinforced With Silicon Carbide and Graphite Particles

Directory of Open Access Journals (Sweden)

S. Mitrović

2014-06-01

Full Text Available The paper presents the wear characteristics of a hybrid composite based on zinc-aluminium ZA27 alloy, reinforced with silicon-carbide and graphite particles. The tested sample contains 5 vol.% of SiC and 3 vol.% Gr particles. Compocasting technique has been used to prepare the samples. The experiments were performed on a “block-on-disc” tribometer under conditions of dry sliding. The wear volumes of the alloy and the composite were determined by varying the normal loads and sliding speeds. The paper contains the procedure for preparation of sample composites and microstructure of the composite material and the base ZA27 alloy. The wear surface of the composite material was examined using the scanning electronic microscope (SEM and energy dispersive spectrometry (EDS. Conclusions were obtained based on the observed impact of the sliding speed, normal load and sliding distance on tribological behaviour of the observed composite.

Impact of automatization in temperature series in Spain and comparison with the POST-AWS dataset

Science.gov (United States)

Aguilar, Enric; López-Díaz, José Antonio; Prohom Duran, Marc; Gilabert, Alba; Luna Rico, Yolanda; Venema, Victor; Auchmann, Renate; Stepanek, Petr; Brandsma, Theo

2016-04-01

Climate data records are most of the times affected by inhomogeneities. Especially inhomogeneities introducing network-wide biases are sometimes related to changes happening almost simultaneously in an entire network. Relative homogenization is difficult in these cases, especially at the daily scale. A good example of this is the substitution of manual observations (MAN) by automatic weather stations (AWS). Parallel measurements (i.e. records taken at the same time with the old (MAN) and new (AWS) sensors can provide an idea of the bias introduced and help to evaluate the suitability of different correction approaches. We present here a quality controlled dataset compiled under the DAAMEC Project, comprising 46 stations across Spain and over 85,000 parallel measurements (AWS-MAN) of daily maximum and minimum temperature. We study the differences between both sensors and compare it with the available metadata to account for internal inhomogeneities. The differences between both systems vary much across stations, with patterns more related to their particular settings than to climatic/geographical reasons. The typical median biases (AWS-MAN) by station (comprised between the interquartile range) oscillate between -0.2°C and 0.4 in daily maximum temperature and between -0.4°C and 0.2°C in daily minimum temperature. These and other results are compared with a larger network, the Parallel Observations Scientific Team, a working group of the International Surface Temperatures Initiative (ISTI-POST) dataset, which comprises our stations, as well as others from different countries in America, Asia and Europe.

241-AW Double Shell Tanks (DST) Integrity Assessment Report

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This report presents the results of the integrity assessment of the 241-AW double-shell tank farm facility located in the 200 East Area of the Hanford Site. The assessment included the design evaluation and integrity examinations of the tanks and concluded that the facility is adequately designed, is compatible with the waste, and is fit for use. Recommendations including subsequent examinations, are made to ensure the continued safe operation of the tanks

Effect of particle size on the friction welding of Al2O3 reinforced 6160 Al alloy composite and SAE 1020 steel

International Nuclear Information System (INIS)

Hascalik, Ahmet; Orhan, Nuri

2007-01-01

The aim of this study is to investigate the feasibility of joining Al 2 O 3 reinforced Al alloy composite to SAE 1020 steel by rotational friction welding. The aluminum-based metal matrix composite (MMC) material containing 5, 10 and 15 vol% Al 2 O 3 particles with average particle sizes of 30 and 60 μm was produced by powder metallurgy technique. The integrity of the joints has been investigated by optical and scanning electron microscopy, while the mechanical properties assessment included microhardness and shear tests. Results indicated that Al/Al 2 O 3 composite could be joined to SAE 1020 steel by friction welding. However, it was pointed out that the quality of the joint was effected negatively with the increase in particle size and volume percentage of the oxide particles in the MMC

Rare earth conversion coatings grown on AA6061 aluminum alloys. Corrosion studies

Energy Technology Data Exchange (ETDEWEB)

Brachetti S, S. B. [Instituto Tecnologico de Ciudad Madero, Av. 1o. de Mayo y Sor Juana I. de la Cruz, Col. Los Mangos, 89440 Ciudad Madero, Tanaulipas (Mexico); Dominguez C, M. A.; Torres H, A. M.; Onofre B, E. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada - Altamira, Carretera Tampico-Puerto Industrial Altamira Km. 14.5, 89600 Altamira, Tamaulipas (Mexico); De la Cruz H, W., E-mail: mdominguezc@ipn.mx [UNAM, Centro de Nanociencias y Nanotecnologia, Apdo. Postal 2681, 22800 Ensenada, Baja California (Mexico)

2014-07-01

The present work is aimed to investigate the corrosion resistance of rare earth protective coatings deposited by spontaneous deposition on AA6061 aluminum alloy substrates. Coatings were deposited from water-based Ce(NO{sub 3}){sub 3} and La(NO{sub 3}){sub 3} solutions by varing parameters such as rare earth solution concentration, bath temperature and immersion time. The values of the Tafel slopes indicate that the cathodic process is favored by concentration polarization rather than activation polarization. Chemical and morphological characterizations of the surface before and after electrochemical evaluations were performed by X-ray photoelectron spectroscopy and scanning electron microscopy. (Author)

Rare earth conversion coatings grown on AA6061 aluminum alloys. Corrosion studies

International Nuclear Information System (INIS)

Brachetti S, S. B.; Dominguez C, M. A.; Torres H, A. M.; Onofre B, E.; De la Cruz H, W.

2014-01-01

The present work is aimed to investigate the corrosion resistance of rare earth protective coatings deposited by spontaneous deposition on AA6061 aluminum alloy substrates. Coatings were deposited from water-based Ce(NO 3 ) 3 and La(NO 3 ) 3 solutions by varing parameters such as rare earth solution concentration, bath temperature and immersion time. The values of the Tafel slopes indicate that the cathodic process is favored by concentration polarization rather than activation polarization. Chemical and morphological characterizations of the surface before and after electrochemical evaluations were performed by X-ray photoelectron spectroscopy and scanning electron microscopy. (Author)

Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

International Nuclear Information System (INIS)

Manes, A.; Pagani, M.; Saponara, M.; Mombelli, D.; Mapelli, C.; Giglio, M.

2014-01-01

Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details

Metallographic characterisation of Al6061-T6 aluminium plates subjected to ballistic impact

Energy Technology Data Exchange (ETDEWEB)

Manes, A., E-mail: andrea.manes@polimi.it; Pagani, M.; Saponara, M.; Mombelli, D.; Mapelli, C.; Giglio, M.

2014-07-01

Al6061-T6 aluminium single layer plates, of different thickness, impacted by two different 7.62 mm Armour Piercing projectiles are studied from a metallographic point of view. The material behaviour after ballistic impact is investigated by optical and scanning electron microscopy as well as by micro-hardness tests. The study allows one to highlight the physical phenomena that happen during the impact: the formation of adiabatic shear bands (ASB), the evolution of softening and hardening phenomena, the creation of petalling, plugging and the formation of a melted film between the target and the penetrator as well as the localised failure mechanism. The thermo-mechanical effects on the target and the penetrator material have been examined in order to investigate in the physical phenomena ruling the ballistic damage; the differences between the two types of impactors are also highlighted. Among interesting findings, it has been noticed that a complete penetration is less detrimental and tungsten core projectile seems more damaging for the structural integrity of Al6061-T6 plates. A complete penetration allows the material to better dissipate the plastic deformation energy induced by bullet whereas the arrest increases localised material softening effect resulting in the formation of ASB. Although the creation of numerical models is not the aim of the present paper, the findings could be useful for the building of a modelling approach capable of replicating all the involved phenomena in details.

Friction stir welding of 6061 aluminium alloy

International Nuclear Information System (INIS)

Abdel Rahman, M.A.M.S.

2009-01-01

6061 AA (Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring a high strength-to-weight ratio and good corrosion resistance such as marine frames, pipelines, storage tanks, and aircraft components [1]. It is also used for the manufacturing of fuel elements in the nuclear research reactors. Compared to many of the fusion welding processes that are routinely used for joining structural alloys, friction stir welding (FSW) is a solid state joining process in which the material that is being welded is not melted and recast [2]. The welding parameters such as tool rotational speed, welding traverse speed, and tool profile play a major role in deciding the weld quality. Several FSW tools (differ from each other in pin angle, shoulder diameter, and shoulder concavity) have been used to fabricate a number of joints in order to obtain a tool with which a sound weld can be produced. It was found that the FSW tool with tapered cone pin, concave shoulder, and shoulder diameter equal to four times the welded plate thickness is suitable to produce a sound weld. The effect of the traverse speed on the global and local tensile properties of friction stir welded joints has been investigated in the 6061-T6 AA. The global tensile properties of the FSW joints were improved with increasing the traverse speed at constant rotation rate. It is found that the global tensile strength of the FSW joint is limited by the local tensile strength of the nearest region to the weld center at which the cross section is composed mainly of the HAZ. The effect of the initial butt surface on the formation of the zigzag line on the tensile properties of the welds was examined by using three types of welding samples differ in the preparation of the initial butt surface. The first type of samples welded without removing the oxide layer from the initial butt surface (uncleaned butt surfaces joint). In the second type of samples the oxide layer was removed from

Producing a particle-reinforced AlCuMgMn alloy by means of mechanical alloying; Herstellung einer partikelverstaerkten AlCuMgMn-Legierung durch mechanisches Legieren

Energy Technology Data Exchange (ETDEWEB)

Nestler, D.; Wielage, B. [TU Chemnitz, Institut fuer Werkstoffwissenschaft und Werkstofftechnik (Germany); Siebeck, S.

2012-07-15

High-energy ball milling (HEM) with subsequent consolidation is a suitable method to produce particle-reinforced aluminium materials. The task of HEM is to distribute the reinforcement particles as homogeneously as possible. A further application of HEM is mechanical alloying (MA). This paper deals with the combination of both applications. Pure metallic powders (Al, Cu, Mg, Mn) were milled together with SiC particles up to 10 h. The composition of the metallic powder corresponds to that of the alloy AA2017 (3.9% Cu, 0.7% Mg, 0.6% Mn). In previous experiments [1], this alloy was used in the form of atomized powder. The changes in microstructure during the formation of the composite powder have been studied by light microscopy, SEM, EDXS and XRD. The results show that the production of composite powders in a single step is possible. This not only allows the economical production of such powders, but also facilitates the use of alloy compositions that are not producible via the melting route, or only producible with difficulty via the melting route. It's possible to produce tailor-made-alloys. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Silica reinforced triblock copolymer gels

DEFF Research Database (Denmark)

Theunissen, E.; Overbergh, N.; Reynaers, H.

2004-01-01

The effect of silica and polymer coated silica particles as reinforcing agents on the structural and mechanical properties of polystyrene-poly(ethylene/butylene)-polystyrene (PS-PEB-PS) triblock gel has been investigated. Different types of chemically modified silica have been compared in order...

Modeling of Particle Emission During Dry Orthogonal Cutting

Science.gov (United States)

Khettabi, Riad; Songmene, Victor; Zaghbani, Imed; Masounave, Jacques

2010-08-01

Because of the risks associated with exposure to metallic particles, efforts are being put into controlling and reducing them during the metal working process. Recent studies by the authors involved in this project have presented the effects of cutting speeds, workpiece material, and tool geometry on particle emission during dry machining; the authors have also proposed a new parameter, named the dust unit ( D u), for use in evaluating the quantity of particle emissions relative to the quantity of chips produced during a machining operation. In this study, a model for predicting the particle emission (dust unit) during orthogonal turning is proposed. This model, which is based on the energy approach combined with the microfriction and the plastic deformation of the material, takes into account the tool geometry, the properties of the worked material, the cutting conditions, and the chip segmentation. The model is validated using experimental results obtained during the orthogonal turning of 6061-T6 aluminum alloy, AISI 1018, AISI 4140 steels, and grey cast iron. A good agreement was found with experimental results. This model can help in designing strategies for reducing particle emission during machining processes, at the source.

An investigation of ductile and brittle reinforcement on the fracture behavior of molybdenum disilicide composites

International Nuclear Information System (INIS)

Brooks, D.; Soboyejo, W.O.

1994-01-01

The results of an ongoing study of the effects of ductile and brittle reinforcement on the fracture toughness of particulate reinforced molybdenum disilicide matrix composites are presented. MoSi 2 composites reinforced with ductile Nb, Mo, and W particles are compared with MoSi 2 composites reinforced with SiC, TiB 2 , and partially stabilized zirconia (PSZ) particles. The effects of different degrees of yttria stabilization on zirconia reinforced composites will also be examined, as well as the effect of solid solution alloying with WSi 2 . The effects of multiple reinforcement of MoSi 2 with 20 vol.% Nb and 20 vol.% unstabilized zirconia (TZ-0) are discussed. The toughening is rationalized using micromechanical models for crack bridging, transformation toughening, and crack deflection

Ultrafiltration and Characterization of AW-101 Supernatant and Entrained Solids

International Nuclear Information System (INIS)

Brooks, K.P.; Bredt, P.R.; Golcar, G.R.; Hartley, S.A.; Urie, M.W.; Tingey, J.M.; Rappe, K.G.; Jagoda, L.K.

1999-01-01

The River Protection Project Waste Treatment Plant (RPP-WTP) (1996) flow sheet uses cross-flow filtration as the solid/liquid separation technique. Unlike traditional dead-end filtration, which has a declining rate caused by the growth of a filter cake on the surface of the filter medium, in cross-flow filtration, the filter cake is swept away by the fluid flowing across it. This filtration method is especially beneficial when there are very fine particles and when system simplicity is required. The objective of this work was to test cross-flow filtration using actual Envelope A Hanford tank waste. Similar to the Phase 1A study, they evaluated the permeability of an Envelope A feed through a single element filter as a function of transmembrane pressure, axial velocity, solids concentration, and time. In addition, the efficiency of back pulse and chemical cleaning on the filter performance was evaluated. The chemical and radiochemical composition of the filtrate and solids was measured to determine efficiency of the filtration process. This report describes the test apparatus, the experimental approach, the results of the tests, and the chemical and radiochemical analysis for supernatants taken from Hanford Tank AW-101. This report also provides a means of transmitting to British Nuclear Fuels, Limited (BNFL) the completed test instruction and raw filtration and analytical data

A comparison of the Glidescope, Pentax AWS, and Macintosh laryngoscopes when used by novice personnel: a manikin study.

LENUS (Irish Health Repository)

Malik, Muhammad A

2009-11-01

Direct laryngoscopic tracheal intubation is a potentially lifesaving procedure, but a difficult skill to acquire and maintain. The consequences of poorly performed intubation attempts are potentially severe. The Pentax AWS and the Glidescope are indirect laryngoscopes that may require less skill to use. We therefore hypothesized that AWS and Glidescope would prove superior to the Macintosh laryngoscope when used by novices in the normal and simulated difficult airway.

Improving Ballistic Performance of Polyurethane Foam by Nanoparticle Reinforcement

Directory of Open Access Journals (Sweden)

M. F. Uddin

2009-01-01

Full Text Available We report improving ballistic performance of polyurethane foam by reinforcing it with nanoscale TiO2 particles. Particles were dispersed through a sonic cavitation process and the loading of particles was 3 wt% of the total polymer. Once foams were reinforced, sandwich panels were made and impacted with fragment simulating projectiles (FSPs in a 1.5-inch gas gun. Projectile speed was set up to have complete penetration of the target in each experiment. Test results have indicated that sandwich with nanophased cores absorbed about 20% more kinetic energy than their neat counterpart. The corresponding increase in ballistic limit was around 12% over the neat control samples. The penetration phenomenon was also monitored using a high-speed camera. Analyses of digital images showed that FSP remained inside the nanophased sandwich for about 7 microseconds longer than that of a neat sandwich demonstrating improved energy absorption capability of the nanoparticle reinforced core. Failure modes for energy absorption have been investigated through a microscope and high-speed images.

Improving Ballistic Performance of Polyurethane Foam by Nanoparticle Reinforcement

International Nuclear Information System (INIS)

Uddin, M.F.; Zainuddin, S.; Mahfuz, H.; Jeelani, S.

2009-01-01

We report improving ballistic performance of polyurethane foam by reinforcing it with nano scale TiO 2 particles. Particles were dispersed through a sonic cavitation process and the loading of particles was 3 wt % of the total polymer. Once foams were reinforced, sandwich panels were made and impacted with fragment simulating projectiles (FSPs) in a 1.5-inch gas gun. Projectile speed was set up to have complete penetration of the target in each experiment. Test results have indicated that sandwich with nano phased cores absorbed about 20% more kinetic energy than their neat counterpart. The corresponding increase in ballistic limit was around 12% over the neat control samples. The penetration phenomenon was also monitored using a high-speed camera. Analyses of digital images showed that FSP remained inside the nano phased sandwich for about 7 microseconds longer than that of a neat sandwich demonstrating improved energy absorption capability of the nanoparticle reinforced core. Failure modes for energy absorption have been investigated through a microscope and high-speed images.

Effects of ultrasonic vibration on microstructure and mechanical properties of nano-sized SiC particles reinforced Al-5Cu composites.

Science.gov (United States)

Li, Jianyu; Lü, Shulin; Wu, Shusen; Gao, Qi

2018-04-01

Ultrasonic vibration (UV) treatment has been successfully applied to improve the particles distribution of nano-sized SiC particles (SiC p ) reinforced Al-5Cu alloy matrix composites which were prepared by combined processes of dry high energy ball milling and squeeze casting. When UV treatment is applied, the distribution of nano-sized SiC p has been greatly improved. After UV for 1 min, large particles aggregates are broken up into small aggregates due to effects of cavitation and the acoustic streaming. After UV for 5 min, all the particles aggregates are dispersed and the particles are uniformly distributed in the composites. Compared with the Al-5Cu matrix alloy, the ultimate tensile strength, yield strength and elongation of the 1 wt% nano-sized SiC p /Al-5Cu composites treated by UV for 5 min are 270 MPa, 173 MPa and 13.3%, which are increased by 7.6%, 6.8% and 29%, respectively. The improvements of mechanical properties after UV are attributed to the uniform distribution of nano particles, grain refinement of aluminum matrix alloy and reduction of porosity in the composites. Copyright © 2017 Elsevier B.V. All rights reserved.

Final Report for the Erosion-Corrosion Anaysis of Tank 241-AW-02E Feed Pump Pit Jumpers B-2 and 1-4 Removed from Service in 2013

Energy Technology Data Exchange (ETDEWEB)

Page, Jason S.

2014-04-07

This document is the final report summarizing the results in the examination of two pipe sections (jumpers) from the tank 241-AW-02E feed pump pit in the 241-AW tank farm. These pipe section samples consisted of jumper AW02E-WT-J-[B – 2] and jumper AW02E-WT-J-[1 – 4]. For the remainder of this report, these jumpers will be referred to as B – 2 and 1 – 4.

Microstructural and mechanical properties of titanium particulate reinforced magnesium composite materials

Energy Technology Data Exchange (ETDEWEB)

Umeda, Junko; Kawakami, Masashi [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaragi, Osaka 567-0047 (Japan); Kondoh, Katsuyoshi, E-mail: kondoh@jwri.osaka-u.ac.jp [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaragi, Osaka 567-0047 (Japan); Ayman, El-Sayed; Imai, Hisashi [Joining and Welding Research Institute, Osaka University, 11-1 Mihogaoka, Ibaragi, Osaka 567-0047 (Japan)

2010-10-01

Pure titanium (Ti) particulate reinforced pure magnesium (Mg) composite materials were fabricated via powder metallurgy route, and their microstructural and mechanical properties were evaluated. When using the elemental mixture of pure Mg and pure Ti powders and consolidating them by solid-state sintering process, no significant increase in tensile strength of the composites was obtained, because of poor bonding strength at the interface between {alpha}-Mg matrix and Ti particles. In particular, coarse magnesium oxide (MgO) particles of about 100 nm were formed via thermite reaction between TiO{sub 2} surface films of Ti particles and Mg raw powders and resulted in preventing the improvement of the mechanical properties of the composite material. On the other hand, when using the atomized pure Mg composite powders reinforced with Ti particulates, their extruded composite material showed obviously improved tensile strength and good elongation, compared to the extruded pure Mg powder material including no Ti particle. The obvious improvement in the tensile strength was due to the restriction of dislocation movement by Ti reinforcements under applied tensile load.

Studies of the AA2519 Alloy Hot Rolling Process and Cladding with EN AW-1050A Alloy

Directory of Open Access Journals (Sweden)

Płonka B.

2016-03-01

Full Text Available The objective of the study was to determine the feasibility of plastic forming by hot rolling of the AA2519 aluminium alloy sheets and cladding these sheets with a layer of the EN AW-1050A alloy. Numerous hot-rolling tests were carried out on the slab ingots to define the parameters of the AA2519 alloy rolling process. It has been established that rolling of the AA2519 alloy should be carried out in the temperature range of 400-440°C. Depending on the required final thickness of the sheet metal, appropriate thickness of the EN AW-1050A alloy sheet, used as a cladding layer, was selected. As a next step, structure and mechanical properties of the resulting AA2519 alloy sheets clad with EN AW-1050A alloy was examined. The thickness of the coating layer was established at 0,3÷0,5mm. Studies covered alloy grain size and the core alloy-cladding material bond strength.

In situ carbon nanotube reinforcements in a plasma-sprayed aluminum oxide nanocomposite coating

International Nuclear Information System (INIS)

Balani, K.; Zhang, T.; Karakoti, A.; Li, W.Z.; Seal, S.; Agarwal, A.

2008-01-01

Carbon nanotubes (CNT) are potential reinforcements for toughening the ceramic matrix. The critical issue of avoiding CNT agglomeration and introducing CNT-matrix anchoring has challenged many researchers to improve the mechanical properties of the CNT reinforced nanocomposite. In the current work, dispersed CNTs are grown on Al 2 O 3 powder particles in situ by the catalytic chemical vapor deposition (CCVD) technique. Consequently, 0.5 wt.% CNT-reinforced Al 2 O 3 particles were successfully plasma sprayed to obtain a 400 μm thick coating on the steel substrate. In situ CNTs grown on Al 2 O 3 shows a promising enhancement in hardness and fracture toughness of the plasma-sprayed coating attributed to the existence of strong metallurgical bonding between Al 2 O 3 particles and CNTs. In addition, CNT tentacles have imparted multi-directional reinforcement in securing the Al 2 O 3 splats. High-resolution transmission electron microscopy shows interfacial fusion between Al 2 O 3 and CNT and the formation of Y-junction nanotubes

In memory of professor Czesław Niżankowski, Head of the Department of Anatomy, Wroclaw Medical University.

Science.gov (United States)

Kacała, Ryszard R; Wronecki, Krzysztof; Kacała, Arkadiusz; Domagała, Zygmunt; Porwolik, Michał

2018-03-20

Professor Czesław Niżankowski was an academic teacher and researcher at several universities; head of the Department of Anatomy at Wroclaw Medical University (1966-1982); and head of the Department of Biological Sciences at the Wrocław School of Physical Education (since 1972 University School of Physical Education in Wrocław), as well as the chancellor there. He contributed greatly to the development of morphological sciences, supervising many doctoral and post-doctoral works. He dedicated considerable time to the preparation of anatomical specimens of lungs, hearts and organs of the gastrointestinal tract. At the Museum of Anatomy, there are over 100 specimens of lungs prepared using the forced air technique improved by Professor Niżankowski, along with specimens of the bronchial tree and vascular system prepared using a corrosive technique. Professor Niżankowski was an active member of scientific societies in Wrocław and in other cities in Poland. For his accomplishments, he received a number of ministerial and state awards, including the Knight's Cross of the Order of Polonia Restituta, and was granted an honorary doctorate by Wroclaw Medical University.

Flow Navigation by Smart Microswimmers via Reinforcement Learning

Science.gov (United States)

Colabrese, Simona; Biferale, Luca; Celani, Antonio; Gustavsson, Kristian

2017-11-01

We have numerically modeled active particles which are able to acquire some limited knowledge of the fluid environment from simple mechanical cues and exert a control on their preferred steering direction. We show that those swimmers can learn effective strategies just by experience, using a reinforcement learning algorithm. As an example, we focus on smart gravitactic swimmers. These are active particles whose task is to reach the highest altitude within some time horizon, exploiting the underlying flow whenever possible. The reinforcement learning algorithm allows particles to learn effective strategies even in difficult situations when, in the absence of control, they would end up being trapped by flow structures. These strategies are highly nontrivial and cannot be easily guessed in advance. This work paves the way towards the engineering of smart microswimmers that solve difficult navigation problems. ERC AdG NewTURB 339032.

Acceptance for Beneficial Use (ABU) Update for 241-AW-104 Waste Transfer Project

International Nuclear Information System (INIS)

MEWES, B.S.

2001-01-01

In October of 2000 an Engineering Task Plan (ETP), RPP-6869, was drafted to define objectives, document requirements, and define organizational responsibilities for the purpose of design installation and turnover of the 241-AW-104 Pump Replacement Project The ETP included an Acceptance for Beneficial Use (ABU) checklist, which delineated all tasks necessary to turn the 241-AW-104 Replaced Transfer Pump over to Operations, Maintenance, and Plant Engineering Signature approval of the respective Engineering Data Transmittal (EDT 630501) signified agreement that the ABU checklist was all-inclusive. In January 2001 an additional EDT (EDT 624153) was drafted to define completed ABU items, provide corresponding supporting documentation, and status open items in need of completion. This supporting document is to serve two purposes: (1) update ABU checklist items completed since January 2001, and (2) define remaining ABU checklist items in need of completion

Influence of load and reinforcement content on selected tribological properties of Al/SiC/Gr hybrid composites

Directory of Open Access Journals (Sweden)

Sandra Veličković

2018-04-01

Full Text Available Hybrid materials with the metal matrix are important engineering materials due to their outstanding mechanical and tribological properties. Here are presented selected tribological properties of the hybrid composites with the matrix made of aluminum alloy and reinforced by the silicon carbide and graphite particles. The tribological characteristics of such materials are superior to characteristics of the matrix – the aluminum alloy, as well as to characteristics of the classical metal-matrix composites with a single reinforcing material. Those characteristics depend on the volume fractions of the reinforcing components, sizes of the reinforcing particles, as well as on the fabrication process of the hybrid composites. The considered tribological characteristics are the friction coefficient and the wear rate as functions of the load levels and the volume fractions of the graphite and the SiC particles. The wear rate increases with increase of the load and the Gr particles content and with reduction of the SiC particles content. The friction coefficient increases with the load, as well as with the SiC particles content increase.

Finite element analysis of Polymer reinforced CRC columns under close-in detonation

DEFF Research Database (Denmark)

Riisgaard, Benjamin

2007-01-01

Polymer reinforced Compact Reinforced Composite, PCRC, is a Fiber reinforced Densified Small Particle system, FDSP, combined with a high strength longitudinal flexural rebar arrangement laced together with polymer lacing to avoid shock initiated disintegration of the structural element under blast...... load. Experimental and numerical results of two PCRC columns subjected to close-in detonation are presented in this paper. Additionally, a LS-DYNA material model suitable for predicting the response of Polymer reinforced Compact Reinforced Concrete improved for close-in detonation and a description...

Effect of the welding parameters on all-weld-metal deposited from AWS E10018-M, E11018-M

International Nuclear Information System (INIS)

Surian, E.

1996-01-01

Using each one of the electrodes types AWS A5.5-81-M, from standard batches, three-all-weld metal test pieces were prepared (cold, warm and hot) according to the AWS A5.5-81 standard. In order to have three different values for the heat input, the welding parameters were varied, but always having in mind the mentioned standard requirements. The test pieces were used to determine the mechanical properties and to carry out metallographic studies. the results obtained showed that the alloy deposited by the E10018-M electrode is less sensible to heat input variations than that from both E11018-M and E12018-M electrodes. Therefore, to work with these last mentioned electrodes it is necessary to have a strict control and very exact instructions, even more exacting than those established in the AWS a5.5.-81 standard. 9 refs

Predicting tensile strength of friction stir welded AA6061 aluminium alloy joints by a mathematical model

International Nuclear Information System (INIS)

Elangovan, K.; Balasubramanian, V.; Babu, S.

2009-01-01

AA6061 aluminium alloy (Al-Mg-Si alloy) has gathered wide acceptance in the fabrication of light weight structures requiring a high strength-to weight ratio and good corrosion resistance. Compared to the fusion welding processes that are routinely used for joining structural aluminium alloys, friction stir welding (FSW) process is an emerging solid state joining process in which the material that is being welded does not melt and recast. This process uses a non-consumable tool to generate frictional heat in the abutting surfaces. The welding parameters such as tool rotational speed, welding speed, axial force etc., and tool pin profile play a major role in deciding the joint strength. An attempt has been made to develop a mathematical model to predict tensile strength of the friction stir welded AA6061 aluminium alloy by incorporating FSW process parameters. Four factors, five levels central composite design has been used to minimize number of experimental conditions. Response surface method (RSM) has been used to develop the model. Statistical tools such as analysis of variance (ANOVA), student's t-test, correlation co-efficient etc. have been used to validate the developed model. The developed mathematical model can be effectively used to predict the tensile strength of FSW joints at 95% confidence level

Evaluation of tank waste transfers at 241-AW tank farm

International Nuclear Information System (INIS)

Willis, W.L.

1998-01-01

A number of waste transfers are needed to process and feed waste to the private contractors in support of Phase 1 Privatization. Other waste transfers are needed to support the 242-A Evaporator, saltwell pumping, and other ongoing Tank Waste Remediation System (TWRS) operations. The purpose of this evaluation is to determine if existing or planned equipment and systems are capable of supporting the Privatization Mission of the Tank Farms and continuing operations through the end of Phase 1B Privatization Mission. Projects W-211 and W-314 have been established and will support the privatization effort. Equipment and system upgrades provided by these projects (W-211 and W-314) will also support other ongoing operations in the tank farms. It is recognized that these projects do not support the entire transfer schedule represented in the Tank Waste Remediation system Operation and Utilization Plan. Additionally, transfers surrounding the 241-AW farm must be considered. This evaluation is provided as information, which will help to define transfer paths required to complete the Waste Feed Delivery (WFD) mission. This document is not focused on changing a particular project, but it is realized that new project work in the 241-AW Tank Farm is required

Supporting document for the historical tank content estimate for AW-tank farm

Energy Technology Data Exchange (ETDEWEB)

Brevick, C.H., Stroup, J.L.; Funk, J.W., Fluor Daniel Hanford

1997-03-06

This Supporting Document provides historical in-depth characterization information on AW-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas.

Supporting document for the historical tank content estimate for AW-tank farm

International Nuclear Information System (INIS)

Brevick, C.H.; Stroup, J.L.; Funk, J.W.

1997-01-01

This Supporting Document provides historical in-depth characterization information on AW-Tank Farm, such as historical waste transfer and level data, tank physical information, temperature plots, liquid observation well plots, chemical analyte and radionuclide inventories for the Historical Tank Content Estimate Report for the Southeast Quadrant of the Hanford 200 Areas

Partially melted zone cracking in AA6061 welds

International Nuclear Information System (INIS)

Prasad Rao, K.; Ramanaiah, N.; Viswanathan, N.

2008-01-01

Partially melted zone (PMZ) cracking susceptibility in AA6061 alloy was studied. Role of prior thermal history, gas tungsten arc welding techniques such as continuous current (CC) and pulsed current (PC) and use of different fillers (AA4043 and AA5356) were studied. Role of different grain refiners such as scandium, zirconium and Tibor in the above fillers was studied. Varestraint test was used to study the PMZ cracking susceptibility. Metallurgical analysis was done to corroborate the results. PMZ cracking was severe in T6 temper than in T4 irrespective of filler material. PMZ cracking susceptibility was more with AA5356 than in AA4043. It was less with pulsed current GTAW. PMZ cracking susceptibility was reduced with addition of grain refiners. Out of all, lowest PMZ cracking susceptibility was observed with 0.5%Sc addition to fusion zone through AA4043 filler and PC technique. The concentrations of magnesium and silicon were reduced at the PMZ grain boundaries with grain refiner additions to fusion zone through AA5356 or AA4043

Partially melted zone cracking in AA6061 welds

Energy Technology Data Exchange (ETDEWEB)

Prasad Rao, K. [Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai (India)], E-mail: kpr@iitm.ac.in; Ramanaiah, N. [Sri Kalahasteeswara Institute of Technology, Srikalahasti (India); Viswanathan, N. [Defence Research and Development Laboratory, Hyderabad (India)

2008-07-01

Partially melted zone (PMZ) cracking susceptibility in AA6061 alloy was studied. Role of prior thermal history, gas tungsten arc welding techniques such as continuous current (CC) and pulsed current (PC) and use of different fillers (AA4043 and AA5356) were studied. Role of different grain refiners such as scandium, zirconium and Tibor in the above fillers was studied. Varestraint test was used to study the PMZ cracking susceptibility. Metallurgical analysis was done to corroborate the results. PMZ cracking was severe in T6 temper than in T4 irrespective of filler material. PMZ cracking susceptibility was more with AA5356 than in AA4043. It was less with pulsed current GTAW. PMZ cracking susceptibility was reduced with addition of grain refiners. Out of all, lowest PMZ cracking susceptibility was observed with 0.5%Sc addition to fusion zone through AA4043 filler and PC technique. The concentrations of magnesium and silicon were reduced at the PMZ grain boundaries with grain refiner additions to fusion zone through AA5356 or AA4043.

Heat input effect of friction stir welding on aluminium alloy AA 6061-T6 welded joint

Directory of Open Access Journals (Sweden)

Sedmak Aleksandar

2016-01-01

Full Text Available This paper deals with the heat input and maximum temperature developed during friction stir welding with different parameters. Aluminium alloy (AA 6061-T6 has been used for experimental and numerical analysis. Experimental analysis is based on temperature measurements by using infrared camera, whereas numerical analysis was based on empirical expressions and finite element method. Different types of defects have been observed in respect to different levels of heat input.

Study on microstructure and tensile properties of fly ash AMCs welded by FSW

Science.gov (United States)

Sachinkumar, Narendranath, S.; Chakradhar, D.

2018-04-01

Aluminum matrix composite (AMCs) constitute a new class of light weight and high strength materials which have widespread applications in almost all engineering sectors. But the cost of AMCs is the only barrier to increase their applications still. Hence there is a huge demand for the composites containing low cost reinforcement with less weight, keeping this in mind, in the present work, Friction stir welding (FSW) of AA6061/SiC/fly ash was carried out successfully. Microstructural study on the welded specimens was performed using optical microscopy (OM) and scanning electron microscopy (SEM). Results indicate that fly ash particles were uniformly distributed in the weld nugget area because of the stirring action of the FSW tool also promoted the grain refinement of the matrix material with complete elimination of clusters present in matrix material which resulting in sound welds without any defects for AA6061/SiC/fly ash composites. 82% of joint efficiency is obtained for selected AMCs. Transverse tensile test results showed that all welds fractured in HAZ.

Comparisons of the Pentax-AWS, Glidescope, and Macintosh Laryngoscopes for Intubation Performance during Mechanical Chest Compressions in Left Lateral Tilt: A Randomized Simulation Study of Maternal Cardiopulmonary Resuscitation

Directory of Open Access Journals (Sweden)

Sanghyun Lee

2015-01-01

Full Text Available Purpose. Rapid advanced airway management is important in maternal cardiopulmonary resuscitation (CPR. This study aimed to compare intubation performances among Pentax-AWS (AWS, Glidescope (GVL, and Macintosh laryngoscope (MCL during mechanical chest compression in 15° and 30° left lateral tilt. Methods. In 19 emergency physicians, a prospective randomized crossover study was conducted to examine the three laryngoscopes. Primary outcomes were the intubation time and the success rate for intubation. Results. The median intubation time using AWS was shorter than that of GVL and MCL in both tilt degrees. The time to visualize the glottic view in GVL and AWS was significantly lower than that of MCL (all P<0.05, whereas there was no significant difference between the two video laryngoscopes (in 15° tilt, P=1; in 30° tilt, P=0.71. The progression of tracheal tube using AWS was faster than that of MCL and GVL in both degrees (all P<0.001. Intubations using AWS and GVL showed higher success rate than that of Macintosh laryngoscopes. Conclusions. The AWS could be an appropriate laryngoscope for airway management of pregnant women in tilt CPR considering intubation time and success rate.

Improving the corrosion resistance of AZ91D magnesium alloy through reinforcement with titanium carbides and borides

Directory of Open Access Journals (Sweden)

Mohamed Gobara

2015-06-01

Full Text Available A composite consisting of magnesium matrix reinforced with a network of TiC–Ti2AlC–TiB2 particulates has been fabricated using a practical in-situ reactive infiltration technique. The microstructural and phase composition of the magnesium matrix composite (R-Mg was investigated using SEM/EDS and XRD. The analyses revealed the complete formation of TiC, Ti2AlC and TiB2 particles in the magnesium matrix. Comparative compression tests of R-Mg and AZ91D alloy showed that the reinforcing particles improve the mechanical properties of Mg alloy. EIS and potentiodynamic polarization results indicated that the reinforcing particles significantly improve the corrosion resistance of the reinforced alloy in 3.5% NaCl solution.

Historical Allotment Gardens in Wrocław - The Need to Protection

Directory of Open Access Journals (Sweden)

Kononowicz Wanda

2016-06-01

Full Text Available Since about the mid-nineteenth century, together with the changing socio-economic situation, different types of allotments appeared in Wrocław. Initially, they were rented gardens, gardens for the poor or for factory workers. At the beginning of the twentieth century, school gardens and the so called Schreber gardens with a large common square were set up as part of Dr. Schreber’s educational health program. In 1914-1918, “war” vegetable gardens were commonly cultivated. In the 1920s allotment gardens began to be systematically introduced to the city plan as permanent, purposefully designed elements of urban greenery. They were often designed together with urban parks, or so called “Folk Parks” of a recreational and sport character. In the 1930s, during the economic crisis, allotments with garden houses were adapted for the unemployed and the homeless to live in. Wrocław allotment gardens have undeniable historical, social, recreational, economic and compositional value. These gardens are a cultural heritage that should be protected. In Western Europe we are witnessing a renaissance of the idea of allotments, while in Poland - a tendency to eliminate them from urban landscapes.

Historical Allotment Gardens in Wrocław - The Need to Protection

Science.gov (United States)

Kononowicz, Wanda; Gryniewicz-Balińska, Katarzyna

2016-06-01

Since about the mid-nineteenth century, together with the changing socio-economic situation, different types of allotments appeared in Wrocław. Initially, they were rented gardens, gardens for the poor or for factory workers. At the beginning of the twentieth century, school gardens and the so called Schreber gardens with a large common square were set up as part of Dr. Schreber's educational health program. In 1914-1918, "war" vegetable gardens were commonly cultivated. In the 1920s allotment gardens began to be systematically introduced to the city plan as permanent, purposefully designed elements of urban greenery. They were often designed together with urban parks, or so called "Folk Parks" of a recreational and sport character. In the 1930s, during the economic crisis, allotments with garden houses were adapted for the unemployed and the homeless to live in. Wrocław allotment gardens have undeniable historical, social, recreational, economic and compositional value. These gardens are a cultural heritage that should be protected. In Western Europe we are witnessing a renaissance of the idea of allotments, while in Poland - a tendency to eliminate them from urban landscapes.

Microstructure and Mechanical Properties of Dissimilar Friction Stir Welding between Ultrafine Grained 1050 and 6061-T6 Aluminum Alloys

Directory of Open Access Journals (Sweden)

Yufeng Sun

2016-10-01

Full Text Available The ultrafine grained (UFGed 1050 Al plates with a thickness of 2 mm, which were produced by the accumulative roll bonding technique after five cycles, were friction stir butt welded to 2 mm thick 6061-T6 Al alloy plates at a different revolutionary pitch that varied from 0.5 to 1.25 mm/rev. In the stir zone, the initial nano-sized lamellar structure of the UFGed 1050 Al alloy plate transformed into an equiaxial grain structure with a larger average grain size due to the dynamic recrystallization and subsequent grain growth. However, an equiaxial grain structure with a much smaller grain size was simultaneously formed in the 6061 Al alloy plates, together with coarsening of the precipitates. Tensile tests of the welds obtained at different welding speeds revealed that two kinds of fracture modes occurred for the specimens depending on their revolutionary pitches. The maximum tensile strength was about 110 MPa and the fractures were all located in the stir zone close to the 1050 Al side.

Bibliography of publications by Bogusław Sałata

Directory of Open Access Journals (Sweden)

Maria A. Chmiel

2014-08-01

Full Text Available Professor Bogusław Sałata, a known and respected Polish mycologist, has died in 1999. His life and achievements were described in the papers Chmiel and Mułenko (1999 and Mułenko and Chmiel (1999. The bibliography is a complete list of works published in 1964-2004. It contains 97 items. This number includes original papers, monographs, books, reviews, translations and articles for the general pulc. The papers are arranged chronologically.

Cultural Heritage Protection Issues In Leśnica, The Settlement Of Wrocław

Science.gov (United States)

Kononowicz, Alena

2015-09-01

Leśnica, today the settlement on the western edge of Wrocław, formerly was an independent town, located on a previously wooded area, with a linear street system. It developed in the Middle Ages around the castle and church playing a service role for the Silesian Piast court on their way to Legnica and during hunting. In the thirteenth century it received city rights, and lost them in the eighteenth century. After the Piast dynasty had died out, it was sold by John of Luxembourg, and repeatedly changed its owners. In the nineteenth century it developed thanks to the industry, tourism and a convenient railway connection to Wrocław as well as hotel and restaurant facilities. In 1928, Leśnica was incorporated into Wrocław. After the Second World War, it lost its cultural continuity. In the 1970's, middle-heigh and high prefabricated buildings were built in the vicinity of a residential district. At the end of the twentieth and early twenty-first century, local industries were liquidated, and intensive land development started, causing the systematic blurring of its small-town character and its urban space started to acquire a character of a big city. In 2004, the old part of Leśnica was entered in the Register of Monuments. Also a ring road was planned, moving the cumbersome and dangerous transit traffic away from historic Średzka Street beyond the southern border of the settlement.

Cultural Heritage Protection Issues In Leśnica, The Settlement Of Wrocław

Directory of Open Access Journals (Sweden)

Kononowicz Alena

2015-09-01

Full Text Available Leśnica, today the settlement on the western edge of Wrocław, formerly was an independent town, located on a previously wooded area, with a linear street system. It developed in the Middle Ages around the castle and church playing a service role for the Silesian Piast court on their way to Legnica and during hunting. In the thirteenth century it received city rights, and lost them in the eighteenth century. After the Piast dynasty had died out, it was sold by John of Luxembourg, and repeatedly changed its owners. In the nineteenth century it developed thanks to the industry, tourism and a convenient railway connection to Wrocław as well as hotel and restaurant facilities. In 1928, Leśnica was incorporated into Wrocław. After the Second World War, it lost its cultural continuity. In the 1970's, middle-heigh and high prefabricated buildings were built in the vicinity of a residential district. At the end of the twentieth and early twenty-first century, local industries were liquidated, and intensive land development started, causing the systematic blurring of its small-town character and its urban space started to acquire a character of a big city. In 2004, the old part of Leśnica was entered in the Register of Monuments. Also a ring road was planned, moving the cumbersome and dangerous transit traffic away from historic Średzka Street beyond the southern border of the settlement.

Dislocation polymorphism transformation of 6061-T651 aluminum alloy processed by laser shock processing: Effect of tempering at the elevated temperatures

International Nuclear Information System (INIS)

Ren, X.D.; Ruan, L.; Yuan, S.Q.; Ren, N.F.; Zheng, L.M.; Zhan, Q.B.; Zhou, J.Z.; Yang, H.M.; Wang, Y.; Dai, F.Z.

2013-01-01

The effects of tempering on surface topography and dislocation configuration of 6061-T651 aluminum alloy by laser shock processing (LSP) were investigated at the elevated temperatures. Surface topography and surface roughness were tested by a Surfcom 130A-Monochrome surface rough-meter. Morphologies of precipitated phases were monitored by scanning electron microscopy (SEM), and the dislocation configurations of samples after LSP were characterized by transmission electron microscope (TEM). The results showed that LSP had a beneficial effect on micro-hardness at elevated temperature. There was a little change of the surface roughness as subjected to LSP. The main strengthening mechanism of micro-hardness was dislocation strengthening and fine grain strengthening, and precipitated phase strengthening was the main strengthening mechanism at elevated temperature. “Dislocation polymorphism transformation” (DPT) effect was affirmed at elevated temperature, and the elevated temperature was principal element for inducing the DPT effect of 6061-T651 aluminum alloy by LSP

Effects of Alloying Elements on the Formation of Core-Shell-Structured Reinforcing Particles during Heating of Al–Ti Powder Compacts

Science.gov (United States)

Chen, Tijun; Gao, Min; Tong, Yunqi

2018-01-01

To prepare core-shell-structured Ti@compound particle (Ti@compoundp) reinforced Al matrix composite via powder thixoforming, the effects of alloying elements, such as Si, Cu, Mg, and Zn, on the reaction between Ti powders and Al melt, and the microstructure of the resulting reinforcements were investigated during heating of powder compacts at 993 K (720 °C). Simultaneously, the situations of the reinforcing particles in the corresponding semisolid compacts were also studied. Both thermodynamic analysis and experiment results all indicate that Si participated in the reaction and promoted the formation of Al–Ti–Si ternary compounds, while Cu, Mg, and Zn did not take part in the reaction and facilitated Al3Ti phase to form to different degrees. The first-formed Al–Ti–Si ternary compound was τ1 phase, and then it gradually transformed into (Al,Si)3Ti phase. The proportion and existing time of τ1 phase all increased as the Si content increased. In contrast, Mg had the largest, Cu had the least, and Si and Zn had an equivalent middle effect on accelerating the reaction. The thicker the reaction shell was, the larger the stress generated in the shell was, and thus the looser the shell microstructure was. The stress generated in (Al,Si)3Ti phase was larger than that in τ1 phase, but smaller than that in Al3Ti phase. So, the shells in the Al–Ti–Si system were more compact than those in the other systems, and Si element was beneficial to obtain thick and compact compound shells. Most of the above results were consistent to those in the semisolid state ones except the product phase constituents in the Al–Ti–Mg system and the reaction rate in the Al–Ti–Zn system. More importantly, the desirable core-shell structured Ti@compoundp was only achieved in the semisolid Al–Ti–Si system. PMID:29342946

Effects of Alloying Elements on the Formation of Core-Shell-Structured Reinforcing Particles during Heating of Al-Ti Powder Compacts.

Science.gov (United States)

Chen, Tijun; Gao, Min; Tong, Yunqi

2018-01-15

To prepare core-shell-structured Ti@compound particle (Ti@compound p ) reinforced Al matrix composite via powder thixoforming, the effects of alloying elements, such as Si, Cu, Mg, and Zn, on the reaction between Ti powders and Al melt, and the microstructure of the resulting reinforcements were investigated during heating of powder compacts at 993 K (720 °C). Simultaneously, the situations of the reinforcing particles in the corresponding semisolid compacts were also studied. Both thermodynamic analysis and experiment results all indicate that Si participated in the reaction and promoted the formation of Al-Ti-Si ternary compounds, while Cu, Mg, and Zn did not take part in the reaction and facilitated Al₃Ti phase to form to different degrees. The first-formed Al-Ti-Si ternary compound was τ1 phase, and then it gradually transformed into (Al,Si)₃Ti phase. The proportion and existing time of τ1 phase all increased as the Si content increased. In contrast, Mg had the largest, Cu had the least, and Si and Zn had an equivalent middle effect on accelerating the reaction. The thicker the reaction shell was, the larger the stress generated in the shell was, and thus the looser the shell microstructure was. The stress generated in (Al,Si)₃Ti phase was larger than that in τ1 phase, but smaller than that in Al₃Ti phase. So, the shells in the Al-Ti-Si system were more compact than those in the other systems, and Si element was beneficial to obtain thick and compact compound shells. Most of the above results were consistent to those in the semisolid state ones except the product phase constituents in the Al-Ti-Mg system and the reaction rate in the Al-Ti-Zn system. More importantly, the desirable core-shell structured Ti@compound p was only achieved in the semisolid Al-Ti-Si system.

Effect of strengthening mechanisms on cold workability and instantaneous strain hardening behavior during grain refinement of AA 6061-10 wt.% TiO2 composite prepared by mechanical alloying

International Nuclear Information System (INIS)

Sivasankaran, S.; Sivaprasad, K.; Narayanasamy, R.; Iyer, Vijay Kumar

2010-01-01

Research highlights: → Various strengthening mechanisms such as solid solution, grain size, precipitate, dislocation and dispersion strengthening promoted yield strength of the composites → The 5 h sintered composite yielded a large plastic strain (23%) at ambient temperature. → The domination of interparticle friction effects, grain size and dislocation strengthening diminished the deformation capacity of the composites greater than 5 h of milling. → Ultra-fine grained composite (40 h) yielded a high strength (>1000 MPa). → The proposed instantaneous new Poisson's ratio and the instantaneous strain hardening index used to study the extent of plastic zone and strain levels of the composite. - Abstract: The mechanical alloying (MA) of AA 6061 alloy reinforced with 10 wt.% fine anatase-titania composites powder milled with different timings (1, 5, 10, 20, 30, and 40 h) was cold consolidated and sintered. The main purpose of this study is to investigate the effect of microstructure and the various strengthening mechanisms such as solid solution, grain size, precipitate, dislocation and dispersion strengthening during grain refinement of AA 6061-10 wt.% TiO 2 composite via MA on cold working and strain hardening behavior. The sintered composite preforms were characterized by X-ray diffraction, scanning electron microscope, and transmission electron microscope. The strengthening mechanisms were estimated by using simplified models available in the literatures. The evaluation of cold deformation behavior under triaxial stress condition through room temperature cold-upsetting tests (incremental loads) was studied by correlating the strengthening mechanisms. Among the developed strengthening mechanisms the grain size and dislocation strengthening mechanisms diminished the deformation capacity of the composites. The strain hardening behavior was also examined by proposing instantaneous strain hardening index (n i ). The value of maximum instantaneous strain

Genomic and secondary metabolite analyses of Streptomyces sp. 2AW provide insight into the evolution of the cycloheximide pathway

Directory of Open Access Journals (Sweden)

Elizabeth eStulberg

2016-05-01

Full Text Available The dearth of new antibiotics in the face of widespread antimicrobial resistance makes developing innovative strategies for discovering new antibiotics critical for the future management of infectious disease. Understanding the genetics and evolution of antibiotic producers will help guide the discovery and bioengineering of novel antibiotics. We discovered an isolate in Alaskan boreal forest soil that had broad antimicrobial activity. We elucidated the corresponding antimicrobial natural products and sequenced the genome of this isolate, designated Streptomyces sp. 2AW. This strain illustrates the chemical virtuosity typical of the Streptomyces genus, producing cycloheximide as well as two other biosynthetically unrelated antibiotics, neutramycin and hygromycin A. Combining bioinformatic and chemical analyses, we identified the gene clusters responsible for antibiotic production. Interestingly, 2AW appears dissimilar from other cycloheximide producers in that the gene encoding the polyketide synthase resides on a separate part of the chromosome from the genes responsible for tailoring cycloheximide-specific modifications. This gene arrangement and our phylogenetic analyses of the gene products suggest that 2AW holds an evolutionarily ancestral lineage of the cycloheximide pathway. Our analyses support the hypothesis that the 2AW glutaramide gene cluster is basal to the lineage wherein cycloheximide production diverged from other glutarimide antibiotics. This study illustrates the power of combining modern biochemical and genomic analyses to gain insight into the evolution of antibiotic-producing microorganisms.

Sampling and Analysis for Tank 241-AW-104 Waste in Support of Evaporator Campaign 2001-1

International Nuclear Information System (INIS)

MCKINNEY, S.G.

2000-01-01

This Tank Sampling and Analysis Plan (TSAP) identifies sample collection, laboratory analysis, quality assurance/quality control (QA/QC), and reporting objectives for the characterization of tank 241-AW-104 waste. Technical bases for these objectives are specified in the 242-A Evaporator Data Quality Objectives (Bowman 2000a and Von Bargen 1998), 242-A Evaporator Quality Assurance Project Plan (Bowman 1998 and Bowman 2000b), Tank 241-AW-104 Sampling Requirements in Support of Evaporator Campaign 2000-1 (Le 2000). Characterization results will be used to support the evaporator campaign currently planned for early fiscal year 2001. No other needs (or issues) requiring data for this tank waste apply to this sampling event

Interface and properties of the friction stir welded joints of titanium alloy Ti6Al4V with aluminum alloy 6061

International Nuclear Information System (INIS)

Wu, Aiping; Song, Zhihua; Nakata, Kazuhiro; Liao, Jinsun; Zhou, Li

2015-01-01

Highlights: • Friction stir butt welding of titanium alloy Ti6Al4V and aluminum alloy A6061-T6. • Welding parameters affect interfacial microstructure of the joint. • Welding parameters affect the mechanical property of joint and fracture position. • Joining mechanism of Ti6Al4V/A6061 dissimilar alloys by FSW is investigated. - Abstract: Titanium alloy Ti6Al4V and aluminum alloy 6061 dissimilar material joints were made with friction stir welding (FSW) method. The effects of welding parameters, including the stir pin position, the rotating rate and the travel speed of the tool, on the interface and the properties of the joints were investigated. The macrostructure of the joints and the fracture surfaces of the tensile test were observed with optical microscope and scanning electron microscope (SEM). The interface reaction layer was investigated with transmission electron microscopy (TEM). The factors affecting the mechanical properties of the joints were discussed. The results indicated that the tensile strength of the joints and the fracture location are mainly dependent on the rotating rate, and the interface and intermetallic compound (IMC) layer are the governing factor. There is a continuous 100 nm thick TiAl 3 IMC at the interface when the rotating rate is 750 rpm. When the welding parameters were appropriate, the joints fractured in the thermo-mechanically affected zone (TMAZ) and the heat affected zone (HAZ) of the aluminum alloy and the strength of the joints could reach 215 MPa, 68% of the aluminum base material strength, as well as the joint could endure large plastic deformation

Enhancing the Hardness and Compressive Response of Magnesium Using Complex Composition Alloy Reinforcement

Directory of Open Access Journals (Sweden)

Khin Sandar Tun

2018-04-01

Full Text Available The present study reports the development of new magnesium composites containing complex composition alloy (CCA particles. Materials were synthesized using a powder metallurgy route incorporating hybrid microwave sintering and hot extrusion. The presence and variation in the amount of ball-milled CCA particles (2.5 wt %, 5 wt %, and 7.5 wt % in a magnesium matrix and their effect on the microstructure and mechanical properties of Mg-CCA composites were investigated. The use of CCA particle reinforcement effectively led to a significant matrix grain refinement. Uniformly distributed CCA particles were observed in the microstructure of the composites. The refined microstructure coupled with the intrinsically high hardness of CCA particles (406 HV contributed to the superior mechanical properties of the Mg-CCA composites. A microhardness of 80 HV was achieved in a Mg-7.5HEA (high entropy alloy composite, which is 1.7 times higher than that of pure Mg. A significant improvement in compressive yield strength (63% and ultimate compressive strength (79% in the Mg-7.5CCA composite was achieved when compared to that of pure Mg while maintaining the same ductility level. When compared to ball-milled amorphous particle-reinforced and ceramic-particle-reinforced Mg composites, higher yield and compressive strengths in Mg-CCA composites were achieved at a similar ductility level.

The role of silicon in the corrosion of AA6061 aluminium alloy laser weldments

Energy Technology Data Exchange (ETDEWEB)

Rahman, A.B.M. Mujibur; Kumar, Sunil [Ian Wark Research Institute, University of South Australia, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia); Gerson, Andrea R. [Applied Centre for Structural and Synchrotron Studies, University of South Australia, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia)], E-mail: Andrea.Gerson@unisa.edu.au

2010-06-15

The galvanic corrosion temporal increase observed on examination of the weld fusion zone (WFZ) of AA6061 laser weldments in 3.5 wt.% NaCl solution cannot be attributed to electron tunnelling as the surface oxide layer is too thick, or the presence of Cl{sup -} within the surface layer as this element was not found to be present. Aluminium alloy and WFZ galvanic and surface analyses indicate that the cathodic WFZ corrosion characteristics are due to increases in silicate concentrations in the surface oxide layer, leading to increased ionic and/or p-type semi-conductor conductivity, intermetallic concentrations and surface area.

The role of silicon in the corrosion of AA6061 aluminium alloy laser weldments

International Nuclear Information System (INIS)

Rahman, A.B.M. Mujibur; Kumar, Sunil; Gerson, Andrea R.

2010-01-01

The galvanic corrosion temporal increase observed on examination of the weld fusion zone (WFZ) of AA6061 laser weldments in 3.5 wt.% NaCl solution cannot be attributed to electron tunnelling as the surface oxide layer is too thick, or the presence of Cl - within the surface layer as this element was not found to be present. Aluminium alloy and WFZ galvanic and surface analyses indicate that the cathodic WFZ corrosion characteristics are due to increases in silicate concentrations in the surface oxide layer, leading to increased ionic and/or p-type semi-conductor conductivity, intermetallic concentrations and surface area.

Reactive wetting of Ti-6Al-4V alloy by molten Al 4043 and 6061 alloys at 600-700 C

Energy Technology Data Exchange (ETDEWEB)

Lin, Qiaoli; Li, Fuxiang; Jin, Peng; Yu, Weiyuan [Lanzhou Univ. of Technology (China). State Key Lab. of Advanced Processing and Recycling of Non-ferrous Metal

2017-06-15

Wetting of Ti-6Al-4V alloy by two industrial grade Al alloys (i.e., Al 6061 and 4043 alloys) was studied using the sessile drop method at 600-700 C under high vacuum. Al/Ti-6Al-4V is a typical reactive wetting system with good final wettability accompanied by the formation of precursor film which is actually an extended reaction layer. The formation mechanism for the precursor film is ''subcutaneous infiltration''. The small amount of alloying element Si in the alloys can cause significant segregation at the liquid/solid interface which satisfies the thermodynamic condition. The wetting behavior can be described by the classic reaction product control models, and Ti{sub 7}Al{sub 5}Si{sub 12} decomposition and Al{sub 3}Ti formation correspond to the two spreading stages. The small difference in alloying elements in Al 6061 and 4043 resulted in distinctly different interface structures, formation of precursor film and spreading dynamics, especially for the Si segregation at the interface.

Effect of the weld thermal cycles by the modified indirect electric arc (MIEA) on the mechanical properties of the AA6061-T6 alloy; Efecto de los ciclo termicos de soldadura por arco electrico indirecto modificado (AEIM) en las propiedades mecanicas de la aleacion AA6061-T6

Energy Technology Data Exchange (ETDEWEB)

Ambriz, R. A.; Barrera, G.; Garcia, R.; Lopez, V. H.

2009-07-01

Results of temperature measurements during welding of 12.7 mm thick AA6061-T6 alloy plates by modified indirect electric arc (MIEA) are presented. This study describes the thermal cycles of the heat affected zone (HAZ) and also in the fusion zone. Depending upon the position of the transducers, the maximum temperatures measured in the HAZ range from 308 to 693 degree centigrade, these measurements were related with the tensile test results, and the failure zone reported previously by the authors. It was observed that, there is a decrease in the mechanical strength of the welded joints, due to the microstructural changes suffered by AA6061-T6 alloy in which formation of the {beta}occurs according to the TTT transformation diagram. The inherent cooling conditions of the weld pool observed for the MIEA technique (only one pass of welding), have permitted to establish the characteristics of solidification and microstructure for a specific cooling rate. (Author) 24 refs.

A Study of Nanoclay Reinforcement of Biocomposites Made by Liquid Composite Molding

Directory of Open Access Journals (Sweden)

Farida Bensadoun

2011-01-01

Full Text Available Liquid composite molding (LCM processes are widely used to manufacture composite parts for the automotive industry. An appropriate selection of the materials and proper optimization of the manufacturing parameters are keys to produce parts with improved mechanical properties. This paper reports on a study of biobased composites reinforced with nanoclay particles. A soy-based unsaturated polyester resin was used as synthetic matrix, and glass and flax fiber fabrics were used as reinforcement. This paper aims to improve mechanical and flammability properties of reinforced composites by introducing nanoclay particles in the unsaturated polyester resin. Four different mixing techniques were investigated to improve the dispersion of nanoclay particles in the bioresin in order to obtain intercalated or exfoliated structures. An experimental study was carried out to define the adequate parameter combinations between vacuum pressure, filling time, and resin viscosity. Two manufacturing methods were investigated and compared: RTM and SCRIMP. Mechanical properties, such as flexural modulus and ultimate strength, were evaluated and compared for conventional glass fiber composites (GFC and flax fiber biocomposites (GFBiores-C. Finally, smoke density analysis was performed to demonstrate the effects and advantages of using an environment-friendly resin combined with nanoclay particles.

Influence of Process Parameters on the Quality of Aluminium Alloy EN AW 7075 Using Selective Laser Melting (SLM)

Science.gov (United States)

Kaufmann, N.; Imran, M.; Wischeropp, T. M.; Emmelmann, C.; Siddique, S.; Walther, F.

Selective laser melting (SLM) is an additive manufacturing process, forming the desired geometry by selective layer fusion of powder material. Unlike conventional manufacturing processes, highly complex parts can be manufactured with high accuracy and little post processing. Currently, different steel, aluminium, titanium and nickel-based alloys have been successfully processed; however, high strength aluminium alloy EN AW 7075 has not been processed with satisfying quality. The main focus of the investigation is to develop the SLM process for the wide used aluminium alloy EN AW 7075. Before process development, the gas-atomized powder material was characterized in terms of statistical distribution: size and shape. A wide range of process parameters were selected to optimize the process in terms of optimum volume density. The investigations resulted in a relative density of over 99%. However, all laser-melted parts exhibit hot cracks which typically appear in aluminium alloy EN AW 7075 during the welding process. Furthermore the influence of processing parameters on the chemical composition of the selected alloy was determined.

Comparison of the Glidescope and Pentax AWS laryngoscopes to the Macintosh laryngoscope for use by advanced paramedics in easy and simulated difficult intubation.

LENUS (Irish Health Repository)

Nasim, Sajid

2009-01-01

BACKGROUND: Intubation of the trachea in the pre-hospital setting may be lifesaving in severely ill and injured patients. However, tracheal intubation is frequently difficult to perform in this challenging environment, is associated with a lower success rate, and failed tracheal intubation constitutes an important cause of morbidity. Novel indirect laryngoscopes, such as the Glidescope and the AWS laryngoscopes may reduce this risk. METHODS: We compared the efficacy of these devices to the Macintosh laryngoscope when used by 25 Advanced Paramedics proficient in direct laryngoscopy, in a randomized, controlled, manikin study. Following brief didactic instruction with the Glidescope and the AWS laryngoscopes, each participant took turns performing laryngoscopy and intubation with each device, in an easy intubation scenario and following placement of a hard cervical collar, in a SimMan manikin. RESULTS: Both the Glidescope and the AWS performed better than the Macintosh, and demonstrate considerable promise in this context. The AWS had the least number of dental compressions in all three scenarios, and in the cervical spine immobilization scenario it required fewer maneuvers to optimize the view of the glottis. CONCLUSION: The Glidescope and AWS devices possess advantages over the conventional Macintosh laryngoscope when used by Advanced Paramedics in normal and simulated difficult intubation scenarios in this manikin study. Further studies are required to extend these findings to the clinical setting.

Synthesis and Characterization of Pine Needles Reinforced RF Matrix Based Biocomposites

Directory of Open Access Journals (Sweden)

A. S. Singha

2008-01-01

Full Text Available Synthesis and characterization of pine needles reinforced thermosetting resin (Resorcinol-Formaldehyde which is most suitable as composite matrix has been reported. The polycondensation reaction between resorcinol and formaldehyde (RF in different molar ratios has been applied to the synthesis of RF polymer matrix. A thermosetting resin based composite, containing approximately 10, 20, 30 and 40% of natural fiber by weight, has been obtained by adding pine needles to the Resorcinol-Formaldehyde (RF resin. The mechanical properties of randomly oriented intimately mixed particle reinforced (Pine needles composites were determined. Effect of fiber loading in terms of weight % on mechanical properties such as tensile, compressive, and flexural and wear properties have also been evaluated. The reinforcing of the resin with Pine needles was accomplished in particle size of 200 micron by employing optimized resin. Present work reveals that mechanical properties of the RF resin increases to extensive extent when reinforced with Pine needles. Thermal (TGA/DTA and morphological studies (SEM of the resin, fiber and polymer composites thus synthesized have also been carried out.

Tenderness, pH and Water Activity (Aw of Spices Dried Meat on Various Concentrate of Ginger Extract (Zingiber Officinale Roscoe and Different Soaking Time

Directory of Open Access Journals (Sweden)

Akhadiyah Afrila

2012-09-01

Full Text Available The objectives of current research were to find out the concentrate of Ginger extract (Zingiber officinale Roscoe and different soaking time of to tenderness, pH, and water activity (Aw, microbial count and sensory evaluation of spices dried meat. The result showed that higher the ginger extract (Zingiber officinale Roscoe concentrate and longer the soaking time, it would give more tenderness, pH, and water activity (Aw to spices dried meat with 15% ginger extract (Zingiber officinale Roscoe extract and 20 minutes length of soaking time. Key Words : Dendeng, ginger, soaking time, tenderness, pH and Aw

Properties of Al2O3 nano-particle reinforced copper matrix composite coatings prepared by pulse and direct current electroplating

International Nuclear Information System (INIS)

Allahkaram, Saeed Reza; Golroh, Setareh; Mohammadalipour, Morteza

2011-01-01

Highlights: → The influence of Al 2 O 3 is studied on morphologies of the DC and PC applied coatings. → The influence of Al 2 O 3 is studied on the DC and PC coating thicknesses. → The influence of Al 2 O 3 is studied on wear resistance. → The effect of Al 2 O 3 is studied on the porosity and corrosion resistance. -- Abstract: Cu-Al 2 O 3 nano-composite coatings have high potential for use in applications in which high mechanical properties together with high corrosion resistance are required. In the present study it is intended to produce copper nano-alumina composite coatings with various nano-alumina contents in order to investigate the effect of alumina reinforcement particles on corrosion resistance and mechanical properties such as hardness and wear resistance. The composite coatings were deposited using direct current (DC) and pulse current (PC) plating. The microstructures of the coatings produced from both methods were examined via scanning electron microscopy (SEM) and X-ray diffraction (XRD) techniques. The wear behaviors, micro hardness, coating thickness, corrosion rate and coating porosity were examined using appropriate methods. Compared to DC deposition, PC plating facilitated higher amounts of particle incorporation with more uniform distribution. The results indicated that the mechanical properties of the applied coatings with incorporated nano-alumina reinforcement were far more superior as compared to its own matrix as well as non-composite copper coatings. It was also found out that increasing the amount of nano-alumina content in the coating, led to enhanced general properties of the coatings.

Influence of Boron on the Creep Behavior and the Microstructure of Particle Reinforced Aluminum Matrix Composites

Directory of Open Access Journals (Sweden)

Steve Siebeck

2018-02-01

Full Text Available The reinforcement of aluminum alloys with particles leads to the enhancement of their mechanical properties at room temperature. However, the creep behavior at elevated temperatures is often negatively influenced. This raises the question of how it is possible to influence the creep behavior of this type of material. Within this paper, selected creep and tensile tests demonstrate the beneficial effects of boron on the properties of precipitation-hardenable aluminum matrix composites (AMCs. The focus is on the underlying microstructure behind this effect. For this purpose, boron was added to AMCs by means of mechanical alloying. Comparatively higher boron contents than in steel are investigated in order to be able to record their influence on the microstructure including the formation of potential new phases as well as possible. While the newly formed phase Al3BC can be reliably detected by X-ray diffraction (XRD, it is difficult to obtain information about the phase distribution by means of scanning electron microscopy (SEM and scanning transmission electron microscopy (STEM investigations. An important contribution to this is finally provided by the investigation using Raman microscopy. Thus, the homogeneous distribution of finely scaled Al3BC particles is detectable, which allows conclusions about the microstructure/property relationship.

Tribomechanical behavior of B{sub 4}C{sub p} reinforced Al 359 composites

Energy Technology Data Exchange (ETDEWEB)

Ramasamy, Deivasigamani; Rathanasamy, Rajasekar [Kongu Engineering College, Tamil Nadu (India). Dept. of Mechanical Engineering; Subramanian, Mohan Kumar; Kaliyannan, Gobinath Velu [PAAVAI Engineering College, Tamil Nadu (India). Dept. of Mechatronics Engineering; Palaniappan, Sathish Kumar [Indian Institute of Technology, Kharagpur, West Bengal (India); Durairaj, Jayanth

2017-03-01

n the present investigation, the influence of B{sub 4}C{sub p} particles on the mechanical and tribological behavior of Al 359 composites has been studied. B{sub 4}C{sub p} particle reinforced Al 359 composite samples were prepared by stir casting process. Hardness, tensile strength and wear behavior of the composites were studied and compared with a control specimen. Hardness of B{sub 4}C{sub p} particles reinforced Al 359 matrix increases compared to base matrix due to the presence of the ceramic phase. Coefficient of friction considerably increases with up to 20 wt.-% addition of B{sub 4}C{sub p} in base matrix. Specimens were subjected to wear tests under different load conditions and the following five different wear mechanisms such as wear groove, abrasion, delamination, oxidation and plastic deformation were evaluated. The abrasion results prove the increase in wear resistance of B{sub 4}C{sub p} reinforced composites compared to a control specimen.

A graphite foam reinforced by graphite particles

Energy Technology Data Exchange (ETDEWEB)

Zhu, J.J.; Wang, X.Y.; Guo, L.F.; Wang, Y.M.; Wang, Y.P.; Yu, M.F.; Lau, K.T.T. [DongHua University, Shanghai (China). College of Material Science and Engineering

2007-11-15

Graphite foam was obtained after carbonization and graphitization of a pitch foam formed by the pyrolysis of coal tar based mesophase pitch mixed with graphite particles in a high pressure and temperature chamber. The graphite foam possessed high mechanical strength and exceptional thermal conductivity after adding the graphite particles. Experimental results showed that the thermal conductivity of modified graphite foam reached 110W/m K, and its compressive strength increased from 3.7 MPa to 12.5 MPa with the addition of 5 wt% graphite particles. Through the microscopic observation, it was also found that fewer micro-cracks were formed in the cell wall of the modified foam as compared with pure graphite foam. The graphitization degree of modified foam reached 84.9% and the ligament of graphite foam exhibited high alignment after carbonization at 1200{sup o}C for 3 h and graphitization at 3000{sup o}C for 10 min.

The feasibility of bonding aluminum alloy 6061 via hot isostatic pressing (HIP)/rolling

International Nuclear Information System (INIS)

Fenolietto, R.A.

1991-01-01

The advantage of developing a HIP bonding process for dispersion fuel plates is that applying a thin cladding in a more uniform manner could allow the upper limit for LEU U 3 Si-Al dispersion fuel plate densities to be overcome. Since much less mechanical deformation would be required, the existing process limitations on the density could be removed, theoretically allowing more fuel to be added. These increases are, of course, subject to irradiation behavior of the higher loadings which is not addressed in this paper. Initial results indicate that aluminum Alloy 6061 can be successfully bonded by seal welding via electron beam (EB), HIPping, and finishing with a limited amount of rolling. (orig.)

Population expansion of some bird species in the city of Wrocław

Directory of Open Access Journals (Sweden)

Kopij Grzegorz

2016-12-01

Full Text Available During the years 2002-2010, distribution and numbers of eight bird species were studied in the whole city of Wrocław, SW Poland (293 km2. The estimation for these species are as follow: Streptopelia turtur: 3 breeding pairs, Upupa epops: 1, Cuculus canorus: 49, Emberiza hortulana: 7, Luscinia megarhynchos: 214-286, Phoenicurus phoenicurus: 87-118, Turdus pilaris: 105-150, Hippolais icterina: 136-181. In comparison with 1980‘s and 1990’s, a rapid increase in the numbers P. phoenicurus, and T. pilaris, and a slight increase of L. megarhynchos and Cuculus canorus were documented. T. pilaris began to breed in the city in the end of 1990‘s. The increase may indicate that the habitats in Wrocław improved both in regard to food availability, nesting sites and other environmental requisitions. The increase in the numbers recorded for C. canorus, P. phoe-nicurus, and L. megarhynchos may also be a result of good conditions prevailing in their wintering grounds in sub-Saharan Africa.

Mechanical Properties of Welded Deformed Reinforcing Steel Bars

Directory of Open Access Journals (Sweden)

Ghafur H. Ahmed

2015-05-01

Full Text Available Reinforcement strength, ductility and bendability properties are important components in design of reinforced concrete members, as the strength of any member comes mainly from reinforcement. Strain compatibility and plastic behaviors are mainly depending on reinforcement ductility. In construction practice, often welding of the bars is required. Welding of reinforcement is an instant solution in many cases, whereas welding is not a routine connection process. Welding will cause deficiencies in reinforcement bars, metallurgical changes and re-crystallization of microstructure of particles. Weld metal toughness is extremely sensitive to the welding heat input that decreases both of its strength and ductility. For determining the effects of welding in reinforcement properties, 48 specimens were tested with 5 different bar diameters, divided into six groups. Investigated parameters were: properties of un-welded bars; strength, ductility and density of weld metal; strength and ductility reduction due to heat input for bundled bars and transverse bars; welding effect on bars’ bending properties; behavior of different joint types; properties of three weld groove shapes also the locations and types of failures sections. Results show that, strength and elongation of the welded bars decreased by (10-40% and (30-60% respectively. Cold bending of welded bars and groove welds shall be prevented.

Rough Sets and Intelligent Systems - Professor Zdzisław Pawlak in Memoriam Volume 2

CERN Document Server

Suraj, Zbigniew

2013-01-01

This book is dedicated to the memory of Professor Zdzis{\\l}aw Pawlak who passed away almost six year ago. He is the founder of the Polish school of Artificial Intelligence and one of the pioneers in Computer Engineering and Computer Science with worldwide influence. He was a truly great scientist, researcher, teacher and a human being. This book prepared in two volumes contains more than 50 chapters. This demonstrates that the scientific approaches  discovered by of Professor Zdzis{\\l}aw Pawlak, especially the rough set approach as a tool for dealing with imperfect knowledge, are vivid and intensively explored by many researchers in many places throughout the world. The submitted papers prove that interest in rough set research is growing and is possible to see many new excellent results both on theoretical foundations and applications of rough sets alone or in combination with other approaches. We are proud to offer the readers this book.

Rough Sets and Intelligent Systems - Professor Zdzisław Pawlak in Memoriam Volume 1

CERN Document Server

Suraj, Zbigniew

2013-01-01

This book is dedicated to the memory of Professor Zdzis{\\l}aw Pawlak who passed away almost six year ago. He is the founder of the Polish school of Artificial Intelligence and one of the pioneers in Computer Engineering and Computer Science with worldwide influence. He was a truly great scientist, researcher, teacher and a human being. This book prepared in two volumes contains more than 50 chapters. This demonstrates that the scientific approaches  discovered by of Professor Zdzis{\\l}aw Pawlak, especially the rough set approach as a tool for dealing with imperfect knowledge, are vivid and intensively explored by many researchers in many places throughout the world. The submitted papers prove that interest in rough set research is growing and is possible to see many new excellent results both on theoretical foundations and applications of rough sets alone or in combination with other approaches. We are proud to offer the readers this book.

Randomized controlled trial of the Pentax AWS, Glidescope, and Macintosh laryngoscopes in predicted difficult intubation.

LENUS (Irish Health Repository)

Malik, M A

2009-11-01

The purpose of this study was to determine the potential for the Pentax AWS and the Glidescope to reduce the difficulty of tracheal intubation in patients at increased risk for difficult tracheal intubation, in a randomized, controlled clinical trial.

Heritage of Stanisław Ostrowski - the only one medical doctor who became state Polish President - Patriae Semper Fidelis.

Science.gov (United States)

Woltanowska, Martyna; Woltanowski, Piotr; Wincewicz, Andrzej; Woltanowska, Magdalena

2018-01-01

Our purpose was to write a biography of Stanisław Ostrowski that would address in the first place the medical aspect of his professional life, with a comprehensive approach of others fields of his activity. We essentially grounded the paper on primary resources that were papers authored by Ostrowski including his scientific publications, memories, speeches as well as contemporaneous official documents that referred to Ostrowski. Second resources were also used to double check some data from primary resources and to place the biography of Stanisław Ostrowski in a proper background with special care to social, professional and political context. In this study, second resources comprised papers, that were prepared after the death of Stanisław Ostrowski. Stanisław Ostrowski, MD was a meticulous military medical doctor with an academic engagement at the King John Casimir University of Lvov. In addition, he was an excellent organizer, who soon got involved in politics to serve the local community with essential projects in public health particularly anti-tuberculosis campaigns in Lvov district. His quiet and proficient nature made him an ideal statesman with incredible skills to reconcile social, national and political enemies. Ostrowski was elected a member of parliament three times. He also held the position of President of the city of Lvov until World War Two. During the war, he was imprisoned and deported to Siberia, Soviet Union, in years 1939-1941. Subsequently he fought against Nazi Germans in the Polish II Corps. Ostrowski survived the war providing medical service in the various military units. Afterwards, he ran his medical practice in the UK. Stanisław Ostrowski was the only dermatologist who became a state president. He held an office of state president of the Polish Republic on exile in London. His life is not a simple story, but a great lesson that provides clear guidelines how to find a stable ground for lifetime being a medical doctor in the

High-temperature mechanical properties and fracture mechanisms of Al–Si piston alloy reinforced with in situ TiB{sub 2} particles

Energy Technology Data Exchange (ETDEWEB)

Han, Gang [School of Mechanical Engineering, Beijing Institute of Technology, 5 South Zhongguancun Street, Haidian District, Beijing 100081 (China); Zhang, Weizheng, E-mail: zhangwz@bit.edu.cn [School of Mechanical Engineering, Beijing Institute of Technology, 5 South Zhongguancun Street, Haidian District, Beijing 100081 (China); Zhang, Guohua; Feng, Zengjian; Wang, Yanjun [Shandong Binzhou Bohai Piston Co., Ltd., Binzhou 256602 (China)

2015-05-01

In order to assess the high-temperature performance of aluminum–silicon alloy reinforced with titanium diboride particles as potential piston material, the tensile behaviors and fracture mechanisms of in situ 4 wt% TiB{sub 2}/Al–Si composite were investigated in the temperature range 25–350 °C. The tensile results revealed that the composite exhibited higher modulus than the matrix alloy at all testing temperatures, but both the matrix alloy and the composite presented similar strength levels above 200 °C. The ductility of the composite was found to be lower than that of the unreinforced matrix alloy at 25 and 200 °C, but no obvious distinction was observed at 350 °C. The effects of temperature and the presence of TiB{sub 2} particles on tensile properties of the composite had been evaluated. Fractographic morphology studies were done using scanning electron microscope, which indicated that the fracture of the composite altered from brittle to ductile mode with temperature increasing. At 25 and 200 °C, fracture was dominated by cracked silicon particles and separated TiB{sub 2} particles, while decohesion at particle–matrix interface was prevalent at 350 °C. Analysis of the fracture surfaces also showed that regions of clustered TiB{sub 2} particles were found to be the locations prone to damage in the composite at both room and high temperatures.

Time-dependent rheoforging of A6061 aluminum alloy on a mechanical servo press and the effects of forming conditions on homogeneity of rheoforged samples

Directory of Open Access Journals (Sweden)

Meng Yi

2015-01-01

Full Text Available The solid and liquid phases in semisolid metal slurry exhibited different forming behaviours during deformation result in products with inhomogeneous quality. A6061 aluminum alloy was forged in the semisolid state on a mechanical servo press with the capability of multistage compression. To improve the homogeneity of rheoforged samples a time-dependent rheoforging strategy was designed. The distributions of the microstructure and mechanical properties the samples manufactured under various experimental conditions were investigated. The A6061 samples forged in the temperature range from 625 to 628 ∘C with a short holding time of 4 s and the upper die preheated to 300 ∘C exhibited a homogeneous microstructure and mechanical properties. The homogeneity of rheoforged samples resulted from the controllable free motion capability of the mechanical servo press and the adjustable fluidity and viscosity of the semisolid slurry.

Recent technical developments at the IMAU: A new generation of AWS and wireless subglacial measurements

NARCIS (Netherlands)

Smeets, C.J.P.P.; Boot, W.; van den Broeke, M.R.; van de Wal, R.S.W.

2011-01-01

Two technical developments are presented: a new generation of AWS and a wireless subglacial measurement system. Both systems build on the experience of the IMAU in developing GPS systems (Den Ouden et al., 2010). Combining methods to minimize energy consumption and wireless communication form the

Reliability of the Attitudes Toward Women Scale (AWS) and the Personal Attributes Questionnaire (PAQ).

Science.gov (United States)

Yoder, Jan D.; And Others

In recent years, there has been a dramatic increase in the volume of empirical research directed toward the issue of sex-roles, including the development of evaluative instruments such as the Attitudes Toward Women Scale (AWS) and the Personal Attributes Questionnaire (PAQ). The United States Military Academy's Project Athena, designed to examine…

Poezja wyjaśniająca swój własny rodowód: Czesław Miłosz a John Ashbery

NARCIS (Netherlands)

van Nieukerken, A.

2011-01-01

A poetry that explains its own genesis: Czesław Miłosz and John Ashbery The first part of this paper considers the origin of the metaphysical import of the constructive principle in the long poems of the ageing Czesław Miłosz (my analysis focuses on "From the Rising of the Sun" and "The separate

Tribological Properties of Aluminum Alloy treated by Fine Particle Peening/DLC Hybrid Surface Modification

Directory of Open Access Journals (Sweden)

Nanbu H.

2010-06-01

Full Text Available In order to improve the adhesiveness of the DLC coating, Fine Particle Peening (FPP treatment was employed as pre-treatment of the DLC coating process. FPP treatment was performed using SiC shot particles, and then AA6061-T6 aluminum alloy was DLC-coated. A SiC-rich layer was formed around the surface of the aluminum alloy by the FPP treatment because small chips of shot particles were embedded into the substrate surface. Reciprocating sliding tests were conducted to measure the friction coefficients. While the DLC coated specimen without FPP treatment showed a sudden increase in friction coefficient at the early stage of the wear cycles, the FPP/DLC hybrid treated specimen maintained a low friction coefficient value during the test period. Further investigation revealed that the tribological properties of the substrate after the DLC coating were improved with an increase in the amount of Si at the surface.

Fatigue Life and Microstructure after Multiple Remelting of A359 Matrix Composites Reinforced with SiC Particles

Directory of Open Access Journals (Sweden)

Klasik A.

2016-12-01

Full Text Available The article presents the results of fatigue life tests and microstructure examinations of A359 alloy matrix composites (F3S.10S and F3S.30S containing 10 and 30wt% of SiC particles, subjected to multiple remelting by conventional gravity casting. Mechanical characteristics were determined in a modified low cycle fatigue (MLCF test, enabling rapid estimation of fatigue life and other mechanical parameters in practice of any material. Qualitative and quantitative metallographic examinations were also carried out. The quantitative evaluation of microstructure was performed by computer image analysis. A set of geometrical parameters of the reinforcing particles, pores and eutectic precipitates present in the metal matrix was determined. The relationships between the mechanical parameters, structural characteristics and the number of remelting operations were presented. It was found that up to the fourth remelting, the mechanical characteristics, including fatigue life, are slightly deteriorated but decrease gradually in the subsequent operations of remelting. The observed effect is mainly due to the shrinkage porosity occurring as a result of gravity casting. To eliminate this defect, the use of squeeze casting process was recommended. It has also been shown that multiple remelting can be an easy and economically well-founded alternative to other more expensive recycling methods.

Study on the Permeability Characteristics of Polyurethane Soil Stabilizer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2017-01-01

Full Text Available A polymer material of polyurethane soil stabilizer (PSS is used to reinforce the sand. To understand the permeability characteristics of PSS reinforced sand, a series of reinforcement layer form test, single-hole permeability test, and porous permeability test of sand reinforced with PSS have been performed. Reinforcement mechanism is discussed with scanning electron microscope images. The results indicated that the permeability resistance of sand reinforced with polyurethane soil stabilizer is improved through the formation of reinforcement layer on the sand surface. The thickness and complete degree of the reinforcement layer increase with the increasing of curing time and PSS concentration. The water flow rate decreases with the increasing of curing time or PSS concentration. The permeability coefficient decreases with the increasing of curing time and PSS concentration and increases with the increasing of depth in specimen. PSS fills up the voids of sand and adsorbs on the surface of sand particle to reduce or block the flowing channels of water to improve the permeability resistance of sand. The results can be applied as the reference for chemical reinforcement sandy soil engineering, especially for surface protection of embankment, slope, and landfill.

Optimization of Burr size, Surface Roughness and Circularity Deviation during Drilling of Al 6061 using Taguchi Design Method and Artificial Neural Network

Directory of Open Access Journals (Sweden)

Reddy Sreenivasulu

2015-03-01

Full Text Available This paper presents the influence of cutting parameters like cutting speed, feed rate, drill diameter, point angle and clearance angle on the burr size, surface roughness and circularity deviation of Al 6061 during drilling on CNC vertical machining center. A plan of experiments based on Taguchi technique has been used to acquire the data. An orthogonal array, signal to noise (S/N ratio and analysis of variance (ANOVA are employed to investigate machining characteristics of Al 6061 using HSS twist drill bits of variable tool geometry and maintain constant helix angle of 45 degrees. Confirmation tests have been carried out to predict the optimal setting of process parameters to validate the used approach, obtained the values of 0.2618mm, 0.1821mm, 3.7451µm, 0.0676mm for burr height, burr thickness, surface roughness and circularity deviation respectively. Finally, artificial neural network has been applied to compare the predicted values with the experimental values, good agreement was shown between the predictive model results and the experimental measurements. Normal 0 false false false EN-US X-NONE X-NONE

ECAP consolidation of Al matrix composites reinforced with in-situ γ-Al{sub 2}O{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Casati, R., E-mail: riccardo.casati@polimi.it [Department of Mechanical Engineering, Politecnico di Milano, Via La Masa 1, Milano (Italy); Fabrizi, A. [Department of Management and Engineering, Università di Padova, Stradella S. Nicola 3, Vicenza (Italy); Tuissi, A. [CNR-IENI, Corso Promessi Sposi 29, Lecco (Italy); Xia, K. [Department of Mechanical Engineering, University of Melbourne, Victoria 3010 (Australia); Vedani, M. [Department of Mechanical Engineering, Politecnico di Milano, Via La Masa 1, Milano (Italy)

2015-11-11

This work is aimed at proposing a method to prepare aluminum matrix composites reinforced with γ-Al{sub 2}O{sub 3} nanoparticles and at describing the effects of an in-situ reaction on the resulting nano-reinforcement dispersed throughout the metal matrix. Al nano- and micro-particles were used as starting materials. They were consolidated by equal channel angular pressing (ECAP) in as-received conditions and after undergoing high-energy ball milling. Further, γ-Al{sub 2}O{sub 3} reinforcing nanoparticles were produced in-situ from the hydroxide layer that covered the Al powder particles. The powder particle morphology and the composites microstructures were investigated by electron microscopy. The transformation process was monitored by X-ray diffraction, differential scanning calorimetry and thermo-gravimetric analysis.

Effect of the weld thermal cycles by the modified indirect electric arc (MIEA) on the mechanical properties of the AA6061-T6 alloy

International Nuclear Information System (INIS)

Ambriz, R. A.; Barrera, G.; Garcia, R.; Lopez, V. H.

2009-01-01

Results of temperature measurements during welding of 12.7 mm thick AA6061-T6 alloy plates by modified indirect electric arc (MIEA) are presented. This study describes the thermal cycles of the heat affected zone (HAZ) and also in the fusion zone. Depending upon the position of the transducers, the maximum temperatures measured in the HAZ range from 308 to 693 degree centigrade, these measurements were related with the tensile test results, and the failure zone reported previously by the authors. It was observed that, there is a decrease in the mechanical strength of the welded joints, due to the microstructural changes suffered by AA6061-T6 alloy in which formation of the βoccurs according to the TTT transformation diagram. The inherent cooling conditions of the weld pool observed for the MIEA technique (only one pass of welding), have permitted to establish the characteristics of solidification and microstructure for a specific cooling rate. (Author) 24 refs

Effect of laser shock processing on fatigue crack growth and fracture toughness of 6061-T6 aluminum alloy

International Nuclear Information System (INIS)

Rubio-Gonzalez, C.; Ocana, J.L.; Gomez-Rosas, G.; Molpeceres, C.; Paredes, M.; Banderas, A.; Porro, J.; Morales, M.

2004-01-01

Laser shock processing (LSP) or laser shock peening is a new technique for strengthening metals. This process induces a compressive residual stress field which increases fatigue crack initiation life and reduces fatigue crack growth rate. Specimens of 6061-T6 aluminum alloy are used in this investigation. A convergent lens is used to deliver 1.2 J, 8 ns laser pulses by a Q-switch Nd:YAG laser, operating at 10 Hz. The pulses are focused to a diameter of 1.5 mm onto a water-immersed type aluminum samples. Effect of pulse density in the residual stress field is evaluated. Residual stress distribution as a function of depth is assessed by the hole drilling method. It is observed that the higher the pulse density the larger the zone size with compressive residual stress. Densities of 900, 1350 and 2500 pulses/cm 2 with infrared (1064 nm) radiation are used. Pre-cracked compact tension specimens were subjected to LSP process and then tested under cyclic loading with R = 0.1. Fatigue crack growth rate is determined and the effect of LSP process parameters is evaluated. Fatigue crack growth rate is compared in specimens with and without LSP process. In addition fracture toughness is determined in specimens with and without LSP treatment. It is observed that LSP reduces fatigue crack growth and increases fracture toughness in the 6061-T6 aluminum alloy

Microstructure and Mechanical Behavior of Microwave Sintered Cu50Ti50 Amorphous Alloy Reinforced Al Metal Matrix Composites

Science.gov (United States)

Reddy, M. Penchal; Ubaid, F.; Shakoor, R. A.; Mohamed, A. M. A.

2018-06-01

In the present work, Al metal matrix composites reinforced with Cu-based (Cu50Ti50) amorphous alloy particles synthesized by ball milling followed by a microwave sintering process were studied. The amorphous powders of Cu50Ti50 produced by ball milling were used to reinforce the aluminum matrix. They were examined by x-ray diffraction (XRD), scanning electron microscopy (SEM), microhardness and compression testing. The analysis of XRD patterns of the samples containing 5 vol.%, 10 vol.% and 15 vol.% Cu50Ti50 indicates the presence of Al and Cu50Ti50 peaks. SEM images of the sintered composites show the uniform distribution of reinforced particles within the matrix. Mechanical properties of the composites were found to increase with an increasing volume fraction of Cu50Ti50 reinforcement particles. The hardness and compressive strength were enhanced to 89 Hv and 449 MPa, respectively, for the Al-15 vol.% Cu50Ti50 composites.

In-situ neutron diffraction measurements of temperature and stresses during friction stir welding of 6061-T6 aluminum alloy

International Nuclear Information System (INIS)

Woo, Wan Chuck; Feng, Zhili; Wang, Xun-Li; Brown, D.W.; Clausen, B.; An, Ke; Choo, Hahn; Hubbard, Camden R.; David, Stan A.

2007-01-01

The evolution of temperature and thermal stresses during friction stir welding of Al6061-T6 was investigated by means of in-situ, time-resolved neutron diffraction technique. A method is developed to deconvolute the temperature and stress from the lattice spacing changes measured by neutron diffraction. The deep penetration capability of neutrons made it possible for the first time to obtain the temperature and thermal stresses inside a friction stir weld

Cloud Computing for Pharmacometrics: Using AWS, NONMEM, PsN, Grid Engine, and Sonic.

Science.gov (United States)

Sanduja, S; Jewell, P; Aron, E; Pharai, N

2015-09-01

Cloud computing allows pharmacometricians to access advanced hardware, network, and security resources available to expedite analysis and reporting. Cloud-based computing environments are available at a fraction of the time and effort when compared to traditional local datacenter-based solutions. This tutorial explains how to get started with building your own personal cloud computer cluster using Amazon Web Services (AWS), NONMEM, PsN, Grid Engine, and Sonic.

The type IIP supernova 2012aw in M95: Hydrodynamical modeling of the photospheric phase from accurate spectrophotometric monitoring

Energy Technology Data Exchange (ETDEWEB)

Dall' Ora, M.; Botticella, M. T.; Della Valle, M. [INAF, Osservatorio Astronomico di Capodimonte, Napoli (Italy); Pumo, M. L.; Zampieri, L.; Tomasella, L.; Cappellaro, E.; Benetti, S. [INAF, Osservatorio Astronomico di Padova, I-35122 Padova (Italy); Pignata, G.; Bufano, F. [Departamento de Ciencias Fisicas, Universidad Andres Bello, Avda. Republica 252, Santiago (Chile); Bayless, A. J. [Southwest Research Institute, Department of Space Science, 6220 Culebra Road, San Antonio, TX 78238 (United States); Pritchard, T. A. [Department of Astronomy and Astrophysics, Penn State University, 525 Davey Lab, University Park, PA 16802 (United States); Taubenberger, S.; Benitez, S. [Max-Planck-Institut für Astrophysik, Karl-Schwarzschild-Str. 1, D-85741 Garching (Germany); Kotak, R.; Inserra, C.; Fraser, M. [Astrophysics Research Centre, School of Mathematics and Physics, Queen' s University Belfast, Belfast, BT7 1NN (United Kingdom); Elias-Rosa, N. [Institut de Ciències de l' Espai (CSIC-IEEC) Campus UAB, Torre C5, Za plata, E-08193 Bellaterra, Barcelona (Spain); Haislip, J. B. [Department of Physics and Astronomy, University of North Carolina at Chapel Hill, 120 E. Cameron Ave., Chapel Hill, NC 27599 (United States); Harutyunyan, A. [Fundación Galileo Galilei - Telescopio Nazionale Galileo, Rambla José Ana Fernández Pérez 7, E-38712 Breña Baja, TF - Spain (Spain); and others

2014-06-01

We present an extensive optical and near-infrared photometric and spectroscopic campaign of the Type IIP supernova SN 2012aw. The data set densely covers the evolution of SN 2012aw shortly after the explosion through the end of the photospheric phase, with two additional photometric observations collected during the nebular phase, to fit the radioactive tail and estimate the {sup 56}Ni mass. Also included in our analysis is the previously published Swift UV data, therefore providing a complete view of the ultraviolet-optical-infrared evolution of the photospheric phase. On the basis of our data set, we estimate all the relevant physical parameters of SN 2012aw with our radiation-hydrodynamics code: envelope mass M {sub env} ∼ 20 M {sub ☉}, progenitor radius R ∼ 3 × 10{sup 13} cm (∼430 R {sub ☉}), explosion energy E ∼ 1.5 foe, and initial {sup 56}Ni mass ∼0.06 M {sub ☉}. These mass and radius values are reasonably well supported by independent evolutionary models of the progenitor, and may suggest a progenitor mass higher than the observational limit of 16.5 ± 1.5 M {sub ☉} of the Type IIP events.

Production of NbC reinforced aluminum matrix composites by mechanical alloying

International Nuclear Information System (INIS)

Silva, Marina Judice; Cardoso, Katia Regina; Travessa, Dilermando Nagle

2014-01-01

Aluminum and their alloys are key materials for the automotive and aerospace industries. The dispersion of hard ceramic particles in the Al soft matrix produces lightweight composites with interesting properties, as environmental resistance, high specific strength and stiffness, high thermal and electrical conductivity, and good wear resistance, encouraging their technological use. Powder metallurgy techniques like mechanical alloying (MA) are very attractive to design metal matrix composites, as they are able to achieve a homogeneous distribution of well dispersed particles inside the metal matrix. In this work, pure aluminum has been reinforced with particles of Niobium carbide (NbC), an extremely hard and stable refractory ceramic. NbC is frequently used as a grain growth inhibitor in micro-alloyed steel due to their low solubility in austenite. In the present work, NbC is expected to act as a reinforcing phase by its fine dispersion into the aluminum matrix, produced by MA. Composite powders produced after different milling times (up to 50h), with 10 and 20% (volume) of NbC were characterized by diffraction laser particle size analysis, scanning electron microscopy (SEM) and by X-ray diffraction (DRX), in order to establish a relationship between the milling time and the characteristics of the powder produced, as size and morphology, crystallite size and reinforcement distribution. This characterization is important in defining the MA process for production of composites for further consolidation by hot extrusion process. (author)

Production of NbC reinforced aluminum matrix composites by mechanical alloying

Energy Technology Data Exchange (ETDEWEB)

Silva, Marina Judice; Cardoso, Katia Regina; Travessa, Dilermando Nagle, E-mail: dilermando.travessa@unifesp.br [Universidade Federal de Sao Paulo (UNIFESP), Sao Jose dos Campos, SP (Brazil). Instituto de Ciencia e Tecnologia

2014-07-01

Aluminum and their alloys are key materials for the automotive and aerospace industries. The dispersion of hard ceramic particles in the Al soft matrix produces lightweight composites with interesting properties, as environmental resistance, high specific strength and stiffness, high thermal and electrical conductivity, and good wear resistance, encouraging their technological use. Powder metallurgy techniques like mechanical alloying (MA) are very attractive to design metal matrix composites, as they are able to achieve a homogeneous distribution of well dispersed particles inside the metal matrix. In this work, pure aluminum has been reinforced with particles of Niobium carbide (NbC), an extremely hard and stable refractory ceramic. NbC is frequently used as a grain growth inhibitor in micro-alloyed steel due to their low solubility in austenite. In the present work, NbC is expected to act as a reinforcing phase by its fine dispersion into the aluminum matrix, produced by MA. Composite powders produced after different milling times (up to 50h), with 10 and 20% (volume) of NbC were characterized by diffraction laser particle size analysis, scanning electron microscopy (SEM) and by X-ray diffraction (DRX), in order to establish a relationship between the milling time and the characteristics of the powder produced, as size and morphology, crystallite size and reinforcement distribution. This characterization is important in defining the MA process for production of composites for further consolidation by hot extrusion process. (author)

Computational analysis of particle reinforced viscoelastic polymer nanocomposites - statistical study of representative volume element

Science.gov (United States)

Hu, Anqi; Li, Xiaolin; Ajdari, Amin; Jiang, Bing; Burkhart, Craig; Chen, Wei; Brinson, L. Catherine

2018-05-01

The concept of representative volume element (RVE) is widely used to determine the effective material properties of random heterogeneous materials. In the present work, the RVE is investigated for the viscoelastic response of particle-reinforced polymer nanocomposites in the frequency domain. The smallest RVE size and the minimum number of realizations at a given volume size for both structural and mechanical properties are determined for a given precision using the concept of margin of error. It is concluded that using the mean of many realizations of a small RVE instead of a single large RVE can retain the desired precision of a result with much lower computational cost (up to three orders of magnitude reduced computation time) for the property of interest. Both the smallest RVE size and the minimum number of realizations for a microstructure with higher volume fraction (VF) are larger compared to those of one with lower VF at the same desired precision. Similarly, a clustered structure is shown to require a larger minimum RVE size as well as a larger number of realizations at a given volume size compared to the well-dispersed microstructures.

Part I. Corrosion studies of continuous alumina fiber reinforced aluminum-matrix composites. Part II. Galvanic corrosion between continuous alumina fiber reinforced aluminum-matrix composites and 4340 steel

Science.gov (United States)

Zhu, Jun

Part I. The corrosion performance of continuous alumina fiber reinforced aluminum-matrix composites (CF-AMCs) was investigated in both the laboratory and field environments by comparing them with their respective monolithic matrix alloys, i.e., pure Al, A1-2wt%Cu T6, and Al 6061 T6. The corrosion initiation sites were identified by monitoring the changes in the surface morphology. Corrosion current densities and pH profiles at localized corrosion sites were measured using the scanning-vibrating electrode technique and the scanning ion-selective electrode technique, respectively. The corrosion damage of the materials immersed in various electrolytes, as well as those exposed in a humidity chamber and outdoor environments, was evaluated. Potentiodynamic polarization behavior was also studied. The corrosion initiation for the composites in 3.15 wt% NaCl occurred primarily around the Fe-rich intermetallic particles, which preferentially existed around the fiber/matrix interface on the composites. The corrosion initiation sites were also caused by physical damage (e.g., localized deformation) to the composite surface. At localized corrosion sites, the buildup of acidity was enhanced by the formation of micro-crevices resulting from fibers left in relief as the matrix corroded. The composites that were tested in exposure experiments exhibited higher corrosion rates than their monolithic alloys. The composites and their monolithic alloys were subjected to pitting corrosion when anodically polarized in the 3.15 wt% NaCl, while they passivated when anodically polarized in 0.5 M Na2SO4. The experimental results indicated that the composites exhibited inferior corrosion resistance compared to their monolithic matrix alloys. Part II. Galvanic corrosion studies were conducted on CF-AMCs coupled to 4340 steel since CF-AMCs have low density and excellent mechanical properties and are being considered as potential jacketing materials for reinforcing steel gun barrels. Coupled and

Benzimidazole as corrosion inhibitor for heat treated 6061 Al- SiCp composite in acetic acid

International Nuclear Information System (INIS)

Chacko, Melby; Nayak, Jagannath

2015-01-01

6061 Al-SiCpcomposite was solutionizedat 350 °C for 30 minutes and water quenched. It was then underaged at 140 °C (T6 treatment). The aging behaviour of the composite was studied using Rockwell B hardness measurement. Corrosion behaviour of the underaged sample was studied in different concentrations of acetic acid and at different temperatures. Benzimidazole at different concentrations was used for the inhibition studies. Inhibition efficiency of benzimidazole was calculated for different experimental conditions. Thermodynamic parameters were found out which suggested benzimidazole is an efficient inhibitor and it adsorbed on to the surface of composite by mixed adsorption where chemisorption is predominant. (paper)

Galvanic corrosion of laser weldments of AA6061 aluminium alloy

International Nuclear Information System (INIS)

Rahman, A.B.M. Mujibur; Kumar, S.; Gerson, A.R.

2007-01-01

Galvanic corrosion of laser welded AA6061 aluminium alloy, arising from the varying rest potentials of the various weldment regions, was examined. The weld fusion zone is found to be the most cathodic region of the weldment while the base material is the most anodic region. The rate of galvanic corrosion, controlled by the cathodic process at the weld fusion zone, increases with time until a steady state maximum is reached. On galvanic corrosion the corrosion potential of the weld fusion zone shifts in the positive direction and the free corrosion current increases. It is proposed that the cathodic process at the weld fusion zone causes a local increase in pH that in turn causes dissolution of the surface film resulting in the loss of Al to solution and the increase of intermetallic phases. The increase in galvanic corrosion may result from either the build up of the intermetallic phases in the surface layer and/or significant increase in surface area of the weld fusion zone due to the porous nature of the surface layer

Microstructure and mechanical properties of spot friction stir welded ultrafine grained 1050 Al and conventional grained 6061-T6 Al alloys

International Nuclear Information System (INIS)

Sun, Y.F.; Fujii, H.; Tsuji, N.

2013-01-01

The ultrafine grained (UFGed) 1050 Al plates with a thickness of 2 mm, which were produced by the accumulative roll bonding technique after 5 cycles, were spot friction stir welded to 2 mm thick 6061-T6 Al alloy plates at different rotation speeds. Although the UFGed 1050 Al plates were used as the lower plates in order to reduce the heat generation therein during the welding process, the initial nano-sized lamellar structure still transformed into an equiaxial grain structure with a grain size of about 5.9 µm in the stir zone of the joints. Simultaneously, coarsening of the precipitates and formation of large quantities of nano-sized subgrains were found in the stir zone of the 6061 Al alloy plates. Microstructural observation by high resolution transmission electron microscope showed that the two plates were bonded through a transitional layer with a thickness of about 15 nm, within which a lot of screw dislocations formed due to the frictional force between the two plates. A mechanical properties evaluation revealed that the maximum shear tensile load can reach about 4127 N and the joints fractured just outside the hook region in the lower 1050 Al plate

Influence of turning Treatments on Al6061 by Offline Inspection Technique

Science.gov (United States)

Annigeri, Ulhas K.; Sandeep, K. L. G.; Prasanna Chaitanya, M.; Sairam Varma, G.; Datta, B. Arun

2018-02-01

Aluminium is mostly extracted from bauxite and is frequently being utilised in the manufacture of sea, land and air vehicles. Since, it has the merit of resistance to corrosion it is frequently being used in sea vehicles. Another outstanding merit of aluminium is its weight which is very less compared to other ferrous materials. In our study, we have selected Al6061 as the material and based on full factorial design the surface roughness has been observed with three base parameters speed, feed and depth of cut. A mathematical model has been developed to predict the surface roughness and also the dominant factor affecting the turning process has been determined. The plots such as main effects, interaction and Pareto chart have been analysed to give an effective conclusion to the process followed in the study. The purpose of these experiments to compare the effect of process treatments in all possible pairs to select the best treatment to the process has been done satisfactorily.

The Development of 6061-Aluminum Windows for the MICE Liquid Absorber

International Nuclear Information System (INIS)

Lau, W.; Yang, S.Q.; Green, M.A.; Ishimoto, S.; Swanson, J.

2005-01-01

The thin windows for the Muon Ionization Cooling Experiment (MICE) liquid Absorber will be fabricated from 6061-T6-aluminum. The absorber and vacuum vessel thin windows are 300-mm in diameter and are 180 mm thick at the center. The windows are designed for an internal burst pressure of 0.68 MPa (100 psig) when warm. The MICE experiment design calls for changeable windows on the absorber, so a bolted window design was adopted. Welded windows offer some potential advantages over bolted windows when they are on the absorber itself. This report describes the bolted window and its seal. This report also describes an alternate window that is welded directly to the absorber body. The welded window design presented permits the weld to be ground off and re-welded. This report presents a thermal FEA analysis of the window seal-weld, while the window is being welded. Finally, the results of a test of a welded-window are presented

Nano-porosity in silica reinforced methyltrimethoxysilane coatings studied by positron beam analysis

NARCIS (Netherlands)

Escobar Galindo, R.; Veen, A. van; Schut, H.; Falub, C.V.; Balkenende, A.R.; With, G. de; Hosson, J.Th.M. De

The porosity in particle reinforced sol-gel coatings has been studied. Silica particles (Ludox-TM40) are introduced into methyl silicate coatings to increase the hardness, the elastic modulus and the fracture toughness. The methyl silicate has a relatively low density (about 1.2 g/cm(2)), while the

Aging Behaviour of 6061 Al-15 vol% SiC Composite in T4 and T6 Treatments

OpenAIRE

Melby Chacko; Jagannath Nayak

2014-01-01

The aging behaviour of 6061 Al-15 vol% SiC composite was investigated using Rockwell B hardness measurement. The composite was solutionized at 350°C and quenched in water. The composite was aged at room temperature (T4 treatment) and also at 140°C, 160°C, 180°C and 200°C (T6 treatment). The natural and artificial aging behaviour of composite was studied using aging curves determined at different temperatures. The aging period for peak aging for different temperatures was identified. The time ...

Running climate model on a commercial cloud computing environment: A case study using Community Earth System Model (CESM) on Amazon AWS

Science.gov (United States)

Chen, Xiuhong; Huang, Xianglei; Jiao, Chaoyi; Flanner, Mark G.; Raeker, Todd; Palen, Brock

2017-01-01

The suites of numerical models used for simulating climate of our planet are usually run on dedicated high-performance computing (HPC) resources. This study investigates an alternative to the usual approach, i.e. carrying out climate model simulations on commercially available cloud computing environment. We test the performance and reliability of running the CESM (Community Earth System Model), a flagship climate model in the United States developed by the National Center for Atmospheric Research (NCAR), on Amazon Web Service (AWS) EC2, the cloud computing environment by Amazon.com, Inc. StarCluster is used to create virtual computing cluster on the AWS EC2 for the CESM simulations. The wall-clock time for one year of CESM simulation on the AWS EC2 virtual cluster is comparable to the time spent for the same simulation on a local dedicated high-performance computing cluster with InfiniBand connections. The CESM simulation can be efficiently scaled with the number of CPU cores on the AWS EC2 virtual cluster environment up to 64 cores. For the standard configuration of the CESM at a spatial resolution of 1.9° latitude by 2.5° longitude, increasing the number of cores from 16 to 64 reduces the wall-clock running time by more than 50% and the scaling is nearly linear. Beyond 64 cores, the communication latency starts to outweigh the benefit of distributed computing and the parallel speedup becomes nearly unchanged.

The Particle Distribution in Liquid Metal with Ceramic Particles Mould Filling Process

Science.gov (United States)

Dong, Qi; Xing, Shu-ming

2017-09-01

Adding ceramic particles in the plate hammer is an effective method to increase the wear resistance of the hammer. The liquid phase method is based on the “with the flow of mixed liquid forging composite preparation of ZTA ceramic particle reinforced high chromium cast iron hammer. Preparation method for this system is using CFD simulation analysis the particles distribution of flow mixing and filling process. Taking the 30% volume fraction of ZTA ceramic composite of high chromium cast iron hammer as example, by changing the speed of liquid metal viscosity to control and make reasonable predictions of particles distribution before solidification.

Jordanian silica sand and cement as a reinforcement material for polystyrene matrix composites

International Nuclear Information System (INIS)

Jalham, S. I.

1999-01-01

The behaviour of polystyrene matrix composites with different percentages of Jordaanian Silica Sand as a Reinforcement Materials (0, 5, 25, 50, and 75 wt%) and different mean grain sizes of sand particles (60, 75, 85, and 300μ m) and with cement as a boning materials in the amount fo 1/6 wt% of the wt% of silica sand were manufactured and tested under compression loading in the Industrial Engineering Department as the Uninersity of Jordan as a part of large study on local materials. The main conclusions of this investigation are: a long-term, durable structure of the polystyrene composite reinforced by silica sand and cement was achieved by mixing the constituents with water; the higher the volume fraction of the reinforcement, the higher the volume fraction of reinforcement, the higher the strength while for 75% of reinforcement, the strength dropped to an amount less than that of the matrix; the higher the grain size, the higher the strength; longitudinal brittle fracture was observed for the composites, and a homogeneous distribution of the sand particles helped in increasing the strength of the composite by playing an important role in distributing the applied load. (author). 11 refs., 6 tabs, 2 figs

The reception of Czesław Miłosz’s poetry by students of primary, lower secondary and upper secondary schools

OpenAIRE

Angelika Matuszek

2013-01-01

The works of Czesław Miłosz are usually regarded as “especially difficult” literature. It is therefore important to examine how young people analyse and interpret selected works of the poet. The article presents the results of a study evaluating the quality of reception of Miłosz’s poetry by students at all levels of compulsory education prior to the Czesław Miłosz Year in 2011. The study enabled the assessment of students’ knowledge of the life and work of Miłosz and the reading competencies...

CHARACTERIZATION OF 6061 T651 ALUMINUM PLATES SUBJECTED TO HIGH-VELOCITY IMPACT LOADS

Directory of Open Access Journals (Sweden)

Evren ÖZŞAHİN

2011-06-01

Full Text Available Ballistic response of single or multi-layered metal armor systems subjected to kinetic energy pro-jectiles was investigated in many experimental, theoretical and numerical studies.In this study, 6061 T651 aluminum plates impacted by 9 mm bullets were investigated. Microstructural investigations have been carried out using optical microscopy. Microhardness values were used to determine the strength behavior of the plates. Influence of the plate thickness and impact velocity on the microstructure has been evaluated. It was concluded from the study that thinner plates are more prone to deformation hardening with high penetration depth values even at low impact velocities while thick plates are more susceptible to thermal softening with less penetration depths. Maximum hardness values were obtained just below the impact zone in both plate thicknesses.

Investigation of Selective Laser Melting Surface Alloyed Aluminium Metal Matrix Dispersive Reinforced Layers

Science.gov (United States)

Kamburov, V. V.; Dimitrova, R. B.; Kandeva, M. K.; Sofronov, Y. P.

2018-01-01

The aim of the paper is to investigate the improvement of mechanical properties and in particular wear resistance of laser surface alloyed dispersive reinforced thin layers produced by selective laser melting (SLM) technology. The wear resistance investigation of aluminium matrix composite layers in the conditions of dry friction surface with abrasive particles and nanoindentation tests were carried out. The process parameters (as scan speed) and their impact on the wear resistant layers have been evaluated. The alloyed layers containing metalized SiC particles were studied by Optical and Scanning Electron Microscopy (SEM) and Energy Dispersive X-ray microanalysis (EDX). The obtained experimental results of the laser alloyed thin layers show significant development of their wear resistance and nanohardness due to the incorporated reinforced phase of electroless nickel coated SiC particles.

Microstructural analysis of as-processed U-10 wt.%Mo monolithic fuel plate in AA6061 matrix with Zr diffusion barrier

Energy Technology Data Exchange (ETDEWEB)

Perez, E.; Yao, B. [Advanced Materials Processing and Analysis Center, Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 (United States); Keiser, D.D. [Nuclear Fuels and Materials Division, Idaho National Laboratory, Scoville, ID 83415 (United States); Sohn, Y.H., E-mail: ysohn@mail.ucf.ed [Advanced Materials Processing and Analysis Center, Department of Mechanical, Materials and Aerospace Engineering, University of Central Florida, Orlando, FL 32816 (United States)

2010-07-01

For higher U-loading in low-enriched U-10 wt.%Mo fuels, monolithic fuel plate clad in AA6061 is being developed as a part of Reduced Enrichment for Research and Test Reactor (RERTR) program. This paper reports the first characterization results from a monolithic U-10 wt.%Mo fuel plate with a Zr diffusion barrier that was fabricated as part of a plate fabrication campaign for irradiation testing in the Advanced Test Reactor (ATR). Both scanning and transmission electron microscopy (SEM and TEM) were employed for analysis. At the interface between the Zr barrier and U-10 wt.%Mo, going from Zr to U(Mo), UZr{sub 2}, {gamma}-UZr, Zr solid-solution and Mo{sub 2}Zr phases were observed. The interface between AA6061 cladding and Zr barrier plate consisted of four layers, going from Al to Zr, (Al, Si){sub 2}Zr, (Al, Si)Zr{sub 3} (Al, Si){sub 3}Zr, and AlSi{sub 4}Zr{sub 5}. Irradiation behavior of these intermetallic phases is discussed based on their constituents. Characterization of as-fabricated phase constituents and microstructure would help understand the irradiation behavior of these fuel plates, interpret post-irradiation examination, and optimize the processing parameters of monolithic fuel system.

Microstructural analysis of as-processed U-10 wt.%Mo monolithic fuel plate in AA6061 matrix with Zr diffusion barrier

Science.gov (United States)

Perez, E.; Yao, B.; Keiser, D. D., Jr.; Sohn, Y. H.

2010-07-01

For higher U-loading in low-enriched U-10 wt.%Mo fuels, monolithic fuel plate clad in AA6061 is being developed as a part of Reduced Enrichment for Research and Test Reactor (RERTR) program. This paper reports the first characterization results from a monolithic U-10 wt.%Mo fuel plate with a Zr diffusion barrier that was fabricated as part of a plate fabrication campaign for irradiation testing in the Advanced Test Reactor (ATR). Both scanning and transmission electron microscopy (SEM and TEM) were employed for analysis. At the interface between the Zr barrier and U-10 wt.%Mo, going from Zr to U(Mo), UZr 2, γ-UZr, Zr solid-solution and Mo 2Zr phases were observed. The interface between AA6061 cladding and Zr barrier plate consisted of four layers, going from Al to Zr, (Al, Si) 2Zr, (Al, Si)Zr 3 (Al, Si) 3Zr, and AlSi 4Zr 5. Irradiation behavior of these intermetallic phases is discussed based on their constituents. Characterization of as-fabricated phase constituents and microstructure would help understand the irradiation behavior of these fuel plates, interpret post-irradiation examination, and optimize the processing parameters of monolithic fuel system.

Electrodeposition of Ni(OH)2 reinforced polyaniline coating for corrosion protection of 304 stainless steel

Science.gov (United States)

Jiang, Li; Syed, Junaid Ali; Gao, Yangzhi; Lu, Hongbin; Meng, Xiangkang

2018-05-01

In the present paper, polyaniline (PANI) coating was electropolymerized in the presence of phosphoric acid with subsequent deposition of Ni(OH)2 particles. The Ni(OH)2 reinforced PANI coating significantly enhances the corrosion resistance of 304 stainless steel (304SS) in comparison with the pristine PANI coating. The galvanostatically deposited Ni(OH)2 particles fill the pores of the pristine PANI coating and improves the coatings hydrophobicity which decreases the diffusion of aggressive media. Importantly, the Rp values of Ni(OH)2 reinforced PANI coating is much higher than that of pristine PANI coating and the Ni(OH)2 reinforced PANI coating presents a long-term anti-corrosive ability (360 h) in 3.5 wt% NaCl solution. The prolonged corrosion protection of Ni(OH)2 reinforced PANI coating is attributed to the improved physical barrier as well as the facile formation of passive oxide film that sustain the anodic protection of the coating.

Ductile-reinforcement toughening in γ-TiAl intermetallic-matrix composites: Effects on fracture toughness and fatigue-crack propagation resistance

International Nuclear Information System (INIS)

Venkateswara Rao, K.T.; Ritchie, R.O.; Odette, G.R.

1994-01-01

The influence of the type, volume fraction, thickness and orientation of ductile phase reinforcements on the room temperature fatigue and fracture resistance of γ-TiAl intermetallic alloys is investigated. Large improvements in toughness compared to monolithic γ-TiAl are observed in both the TiNb- and Nb-reinforced composites under monotonic loading. Toughness increases with increasing ductile phase content, reinforcement thickness and strength; orientation effect are minimal. Crack-growth behavior is characterized by steep resistance curves primarily due to crack trapping/renucleation and extensive crack bridging by the ductile-phase particles. In contrast, under cyclic loading the influence of ductile phases on fatigue resistance is strongly dependent upon reinforcement orientation. Compared to monolithic γ-TiAl, improvements in fatigue-crack growth resistance are observed in TiNb-reinforced composites only in the face (C-L) orientation; crack-growth rates for the edge (C-R) orientation are actually faster in the composite. In comparison, Nb-particle reinforcements offer less toughening under monotonic loading but enhance the fatigue properties compared to TiNb reinforcements under cyclic loading

Matrix-reinforcement reactivity in P/M titanium matrix composites

International Nuclear Information System (INIS)

Amigo, V.; Romero, F.; Salvador, M. D.; Busquets, D.

2007-01-01

The high reactivity of titanium and the facility of the same one to form intermetallics makes difficult obtaining composites with this material and brings the need in any case of covering the principal fibres used as reinforcement. To obtain composites of titanium reinforced with ceramic particles ins proposed in this paper, for this reason it turns out to be fundamental to evaluate the reactivity between the matrix and reinforcement. Both titanium nitride and carbide (TiN and TiC) are investigated as materials of low reactivity whereas titanium silicide (TiSi 2 ) is also studied as materials of major reactivity, already stated by the scientific community. This reactivity will be analysed by means of scanning electron microscopy (SEM) there being obtained distribution maps of the elements that allow to establish the possible influence of the sintering temperature and time. Hereby the matrix-reinforcement interactions are optimized to obtain suitable mechanical properties. (Author) 39 refs

Numerical and experimental validation of a particle Galerkin method for metal grinding simulation

Science.gov (United States)

Wu, C. T.; Bui, Tinh Quoc; Wu, Youcai; Luo, Tzui-Liang; Wang, Morris; Liao, Chien-Chih; Chen, Pei-Yin; Lai, Yu-Sheng

2018-03-01

In this paper, a numerical approach with an experimental validation is introduced for modelling high-speed metal grinding processes in 6061-T6 aluminum alloys. The derivation of the present numerical method starts with an establishment of a stabilized particle Galerkin approximation. A non-residual penalty term from strain smoothing is introduced as a means of stabilizing the particle Galerkin method. Additionally, second-order strain gradients are introduced to the penalized functional for the regularization of damage-induced strain localization problem. To handle the severe deformation in metal grinding simulation, an adaptive anisotropic Lagrangian kernel is employed. Finally, the formulation incorporates a bond-based failure criterion to bypass the prospective spurious damage growth issues in material failure and cutting debris simulation. A three-dimensional metal grinding problem is analyzed and compared with the experimental results to demonstrate the effectiveness and accuracy of the proposed numerical approach.

Behavior of reinforced concrete beams reinforced with GFRP bars

Directory of Open Access Journals (Sweden)

D. H. Tavares

Full Text Available The use of fiber reinforced polymer (FRP bars is one of the alternatives presented in recent studies to prevent the drawbacks related to the steel reinforcement in specific reinforced concrete members. In this work, six reinforced concrete beams were submitted to four point bending tests. One beam was reinforced with CA-50 steel bars and five with glass fiber reinforced polymer (GFRP bars. The tests were carried out in the Department of Structural Engineering in São Carlos Engineering School, São Paulo University. The objective of the test program was to compare strength, reinforcement deformation, displacement, and some anchorage aspects between the GFRP-reinforced concrete beams and the steel-reinforced concrete beam. The results show that, even though four GFRP-reinforced concrete beams were designed with the same internal tension force as that with steel reinforcement, their capacity was lower than that of the steel-reinforced beam. The results also show that similar flexural capacity can be achieved for the steel- and for the GFRP-reinforced concrete beams by controlling the stiffness (reinforcement modulus of elasticity multiplied by the bar cross-sectional area - EA and the tension force of the GFRP bars.

Mechanical behaviour of aluminium matrix composites with particles in high temperature

International Nuclear Information System (INIS)

Amigo, V.; Salvador, M. D.; Ferrer, C.; Costa d, C. E.; Busquets, D.

2001-01-01

The aluminium matrix composites materials reinforced by ceramic particles can be elaborated by powder metallurgy techniques, with extrusion processes. These can provide new materials, with a better mechanical behaviour and moreover when we need those properties at higher temperatures. Aluminium alloy reinforced composites with silicon nitride particles by powder extrusion process was done. Their mechanical properties were characterised at room and elevated temperatures. (Author) 28 refs

Effect of ageing on tensile behavior of ultrafine grained Al 6061 alloy

Energy Technology Data Exchange (ETDEWEB)

Rao, P. Nageswara [Department of Metallurgical and Materials Engineering & Centre of Nanotechnology, IIT Roorkee, Roorkee 247667 (India); Singh, Dharmendra [Department of Mechanical Engineering, Government Engineering College, Bikaner 304001 (India); Brokmeier, Heinz-Günter [Helmholtz Zentrum Geesthacht, Max Planck Straße 1, Geb 33, D-21502 Geesthacht (Germany); Jayaganthan, R., E-mail: rjayafmt@iitr.ernet.in [Department of Metallurgical and Materials Engineering & Centre of Nanotechnology, IIT Roorkee, Roorkee 247667 (India)

2015-08-12

In the present investigation, the ageing behavior of ultrafine grained (UFG) Al 6061 alloy, processed through multi-directional forging (MDF) at cryogenic temperature was investigated. The evolution of microstructure was investigated through transmission electron microscopy and electron back scattered diffraction technique. The results indicate that homogeneous microstructure with an ultrafine grain morphology (average size 250 nm) was achieved through cryogenic forging of the alloy subjected to prior solutionising treatment. Tensile testing at room temperature revealed that MDFed material after ageing led to significant improvement in work hardening and its tensile ductility. Strengthening of the matrix through various mechanisms has been quantified with the existing models to estimate the yield strength of the as forged and peak aged material. The precipitation hardening response in UFG material is found to be 35% lower than that of the coarse grained material as observed in the present work.

Particles geometry influence in the thermal stress level in an SiC reinforced aluminum matrix composite considering the material non-linear behavior

International Nuclear Information System (INIS)

Miranda, Carlos A. de J.; Libardi, Rosani M.P.; Boari, Zoroastro de M.

2009-01-01

An analytical methodology was developed to predict the thermal stress level that occurs in a metallic matrix composite reinforced with SiC particles, when the temperature decreases from 600 deg C to 20 deg C during the fabrication process. This analytical development is based on the Eshelby method, dislocation mechanisms, and the Maxwell-Boltzmann distribution model. The material was assumed to have a linear elastic behavior. The analytical results from this formulation were verified against numerical linear analyses that were performed over a set of random non-uniform distribution of particles that covers a wide range of volumetric ratios. To stick with the analytical hypothesis, particles with round geometry were used. Each stress distribution, represented by the isostress curves at ΔT=-580 deg C, was analyzed with an image analyzer. A statistical procedure was applied to obtain the most probable thermal stress level. Analytical and numerical results compared very well. Plastic deformation as well as particle geometry can alter significantly the stress field in the material. To account for these effects, in this work, several numerical analyses were performed considering the non-linear behavior for the aluminum matrix and distinct particle geometries. Two distinct sets of data with were used. To allow a direct comparison, the first set has the same models (particle form, size and distribution) as used previously. The second set analyze quadrilateral particles and present very tight range of volumetric ratio, closer to what is found in actual SiC composites. A simple and fast algorithm was developed to analyze the new results. The comparison of these results with the previous ones shows, as expected, the strong influence of the elastic-plastic behavior of the aluminum matrix on the composite thermal stress distribution due to its manufacturing process and shows, also, a small influence of the particles geometry and volumetric ratio. (author)

Development of an Extrusion Process to Ameliorate the Tribological Properties of Heat Treated Al Mg Si (Cu System Alloys Matrix Composites in Consolidated State

Directory of Open Access Journals (Sweden)

M.O. Shabani

2012-09-01

Full Text Available The developments of AA6061 aluminum matrix composites are of great interest in industrial applications for lighter materials with high specific strength, stiffness and wear resistance. In this article, the dry wear behavior of AA6061 matrix composites was investigated under different sliding speeds and applied loads. It is observed that the composites exhibit higher friction coefficients and greater wear resistances than the Al alloy against the steel disc surface. Low-speed wear rates are associated with abrasive wear,indicating the dominant wear mechanism, though minor, delamination wear may be produced. Abrasive wear associates with the formation of deep scratches on the worn surface in the sliding direction. For a given load and sliding velocity the extent of iron transfer is highest in case of 15 % SiC reinforced Al6061 composite among all the material studied.

Particle-Reinforced Aluminum Matrix Composites (AMCs—Selected Results of an Integrated Technology, User, and Market Analysis and Forecast

Directory of Open Access Journals (Sweden)

Anja Schmidt

2018-02-01

Full Text Available The research and development of new materials such as particle-reinforced aluminum matrix composites (AMCs will only result in a successful innovation if these materials show significant advantages not only from a technological, but also from an economic point of view. Against this background, in the Collaborative Research Center SFB 692, the concept of an integrated technology, user, and market analysis and forecast has been developed as a means for assessing the technological and commercial potential of new materials in early life cycle stages. After briefly describing this concept, it is applied to AMCs and the potential field of manufacturing aircraft components. Results show not only technological advances, but also considerable economic potential—the latter one primarily resulting from the possible weight reduction being enabled by the increased yield strength of the new material.

Fracture and fatigue considerations in the development of ductile-phase reinforced intermetallic-matrix composites

International Nuclear Information System (INIS)

Venkateswara Rao, K.T.; Ritchie, R.O.

1994-01-01

The salient microstructural factors influencing fracture and fatigue-crack growth resistance of ductile-particle reinforced intermetallic-matrix composites at ambient temperature are reviewed through examples from the Nb/MoSi 2 , TiNb/TiAl, Nb/TiAl and Nb/Nb 3 Al systems; specific emphasis is placed on properties and morphology of the reinforcement and its interfacial properties with the matrix. It is shown that composites must be fabricated with a high aspect ratio ductile-reinforcement morphology in order to promote crack-particle interception and resultant crack bridging for improved fracture and fatigue properties. Concurrently, however, the ductile phases have contrasting effects on crack growth under monotonic vs. cyclic loading suggesting that composite microstructures tailored for optimal toughness may not necessarily yield optimal fatigue resistance. Perspectives for the future development of damage-tolerant intermetallic-composite microstructures are discussed

Phosphated in aluminium 6061-T651 used in the pool of the TRIGA Mark III nuclear reactor; Fosfatado en aluminio 6061-T651 utilizado en la tina del reactor nuclear TRIGA Mark III

Energy Technology Data Exchange (ETDEWEB)

Aguilar H, F.; Espinosa L, J.; Pena B, A.; Perez F, C.; Sanchez C, M.; Vite T, M.; Vite T, J. [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

2001-07-01

We characterized a phosphated coating used a substrate in aluminium 6061-T651, which is used in the container of the TRIGA Mark III nuclear reactor. Characterization was made using MEB and X-ray diffraction techniques. Coating application has the function to prevent the corrosion. Coating was probed to test adhesion in accordance with the Standard ASTM D-4541, and the corrosion process using a salt spray (fog) camera, in accordance with the Standard ASTM B-117, so as we could phosphate the welding cord. These experiences were obtained using a Deep cell. Results obtained are going to phosphate 'in situ' using a mobile device which was patented for the National Institute of Nuclear Research (ININ) in the Mexican Institute of Intellectual Property (INPI). (Author)

Niobium Carbide-Reinforced Al Matrix Composites Produced by High-Energy Ball Milling

Science.gov (United States)

Travessa, Dilermando Nagle; Silva, Marina Judice; Cardoso, Kátia Regina

2017-06-01

Aluminum and its alloys are key materials for the transportation industry as they contribute to the development of lightweight structures. The dispersion of hard ceramic particles in the Al soft matrix can lead to a substantial strengthening effect, resulting in composite materials exhibiting interesting mechanical properties and inspiring their technological use in sectors like the automotive and aerospace industries. Powder metallurgy techniques are attractive to design metal matrix composites, achieving a homogeneous distribution of the reinforcement into the metal matrix. In this work, pure aluminum has been reinforced with particles of niobium carbide (NbC), an extremely hard and stable refractory ceramic. Its use as a reinforcing phase in metal matrix composites has not been deeply explored. Composite powders produced after different milling times, with 10 and 20 vol pct of NbC were produced by high-energy ball milling and characterized by scanning electron microscopy and by X-ray diffraction to establish a relationship between the milling time and size, morphology, and distribution of the particles in the composite powder. Subsequently, an Al/10 pct NbC composite powder was hot extruded into cylindrical bars. The strength of the obtained composite bars is comparable to the commercial high-strength, aeronautical-grade aluminum alloys.

Flow modelling of steel fibre reinforced self-compacting concrete

DEFF Research Database (Denmark)

Svec, Oldrich

was done by means of the Immersed boundary method with direct forcing. Evolution of the immersed particles was described by Newton's differential equations of motion. The Newton's equations were solved by means of Runge-Kutta-Fehlberg iterative scheme. Several challenges had to be overcome during...... in concrete can efficiently substitute or supplement conventional steel reinforcement, such as reinforcement bars. Ordinary concrete composition further makes the material stiff and non-flowable. Self-compacting concrete is an alternative material of low yield stress and plastic viscosity that does flow...... of the fluid near formwork surface. A method to incorporate the apparent slip into the Lattice Boltzmann fluid dynamics solver was suggested. The proposed numerical framework was observed to correctly predict flow of fibre reinforced self-compacting concrete. The proposed numerical framework can therefore...

Influence of clinical experience of the Macintosh laryngoscope on performance with the Pentax-AWS Airway Scope(®), a rigid video-laryngoscope, by paramedics in Japan.

Science.gov (United States)

Ota, Kohei; Sadamori, Takuma; Kusunoki, Shinji; Otani, Tadatsugu; Tamura, Tomoko; Une, Kazunobu; Kida, Yoshiko; Itai, Junji; Iwasaki, Yasumasa; Hirohashi, Nobuyuki; Nakao, Masakazu; Tanigawa, Koichi

2015-10-01

We sought to establish the clinical utility of the Pentax-AWS Airway Scope(®) (AWS) when used by paramedics to intubate the trachea, and to evaluate whether their performance was influenced by previous clinical experience with the Macintosh laryngoscope (ML). Twenty paramedics attempted tracheal intubation using the AWS in five patients each in the operating room. We recorded the success rate, the number of intubation attempts, and the time for intubation and adverse events, and compared these based on the paramedics' previous clinical experience with the ML. Ten paramedics had no prior clinical experience of the ML (group A) and 10 had used it on more than 30 occasions (group B). The intubation success rate was 99 % (99/100). Notably, 96 % (47/49) of intubations were achieved on the first attempt by the inexperienced paramedics in group A, compared with 64 % (32/50) by the experienced paramedics in group B (p = 0.0001). The time to intubation (mean ± SD) was significantly shorter in group A than in group B (37 ± 24 vs. 48 ± 21 s, p = 0.002). There were marked variations in the times taken to intubate, but no apparent improvement as the intubators gained experience between their first and fifth cases. No complications were encountered in either group. We found that paramedics could achieve a high tracheal intubation success rate using the AWS independent of previous airway management experience. Better intubation performance with the AWS was observed in paramedics without clinical experience with the ML.

Pit nucleation on as-cast aluminiuim alloy AW-5083 in 0.01M NaCl

Directory of Open Access Journals (Sweden)

Dolić N.

2011-01-01

Full Text Available The use of aluminium alloys in a wide range of technical applications is related mostly to the two facts: they facilitate weight saving of final products (if compared to the steel and they are prone to spontaneous passivity due to the coherent surface oxide layer which impedes further reaction of aluminium with the environment. Among the commercial Al alloys, EN AW-5083 alloy is a representative non-heat treatable Al-Mg based alloy which possesses many interesting characteristics as a structural material, such as low price, moderately high strength, high formability in conjunction with superplasticity and good corrosion resistance in marine atmospheres. Aiming to enhance the knowledge of possible interactions of studied alloy EN AW-5083 in as-cast condition with chloride media, electrochemical measurements were used to follow the pitting behaviour in 0.01 M NaCl. The results of tests have shown that susceptibility of alloy to pitting corrosion is strongly influenced by the microstructural constituents of the alloy in as-cast condition.

Fabrication of polystyrene/agave particle biocomposites using ...

Indian Academy of Sciences (India)

Polystyrene (PS) composites reinforced with ungrafted and acrylonitrile (AN) grafted agave particles (AgP) have been prepared with 10–30% particle content by weight using compression molding technique. The composite specimens thus prepared were subjected to the evaluation of mechanical, chemical, flammability and ...

Preparation of nickel-coated titanium carbide particulates and their use in the production of reinforced iron matrix composites

International Nuclear Information System (INIS)

Yi, Danqing; Yu, Pengchao; Hu, Bin; Liu, Huiqun; Wang, Bin; Jiang, Yong

2013-01-01

Highlights: • Ni-coated TiC composite powders were prepared by electroless plating. • Iron-based composites reinforced by TiC particles was prepared by HIP. • Mechanical and wear properties were improved with the addition of Ni-coated TiC. • The nickel coating promotes the formation and growth of sintering neck. - Abstract: Ni-coated titanium carbide (TiC) composite powders were prepared by electroless plating (EP). Further, using hot isostatic pressing (HIP), iron matrix composites reinforced with 4 wt% Ni-coated TiC particulates with relative density close to 100% were prepared. The microstructure and phase composition of the Ni-coated powders and the composites were analyzed using X-ray diffraction, scanning electron microscopy, and energy dispersive X-ray spectroscopy. The results showed that the TiC particles were distributed uniformly in the matrix and were free of segregation or coarsening. Compared to the TiC particles without Ni coating, the reinforced iron-based composites containing the Ni-coated particles showed higher relative densities and better mechanical properties. The density, hardness, tensile strength, and elongation were enhanced to 99.98%, 243 HV, 565 MPa, and 11.7%, respectively in composites containing Ni-coated TiC particles from 99.70%, 210 HV, 514 MPa, and 10.3%, respectively in composites that were prepared using particles without Ni coating. In addition, the mass losses in the composites containing the Ni-coated particles were reduced by 32–75% in the abrasive wear test with various vertical loads. We propose that the nickel coatings on the particulates had a beneficial effect on the microstructure and properties of the reinforced iron-based composites is due to promotion of neck formation and growth between TiC and iron powders during sintering, which enhanced the density of the sintered compact and the bonding strength between the TiC particles and the iron matrix

Effect of material strength on the relationship between the principal Hugoniot and quasi-isentrope of beryllium and 6061-T6 aluminum below 35 GPa

International Nuclear Information System (INIS)

Moss, W.C.

1985-01-01

Quasi-isentropic (QI) compression can be achieved by loading a specimen with a low strain rate, long rise time uniaxial strain wave. Recent experimental data show that the quasi-isentrope of 6061-T6 aluminum lies a few percent above the principal Hugoniot, that is, at a given specific volume, the QI stress exceeds the principal Hugoniot stress. It has been suggested that this effect is due to material strength. Using Hugoniot data, shock-reshock, and shock-unload data for beryllium and 6061-T6 aluminum, we have constructed the quasi-isentropes as functions of specific volume. Our results show that the QI stress exceeds the principal Hugoniot stress above a Hugoniot stress of 8.4 GPa in beryllium, and between Hugoniot stresses of 3.8 and 21.4 GPa in aluminum. The effect is due to strength and implies that the QI yield strength can be large. Our calculations show that the QI yield strength is 0.9 GPa in aluminum at a QI stress of 9 GPa, and 5.2 GPa in beryllium at a QI stress of 35 GPa

Development of new ferritic alloys reinforced by nano titanium nitrides

International Nuclear Information System (INIS)

Mathon, M.H.; Perrut, M.; Poirier, L.; Ratti, M.; Hervé, N.; Carlan, Y. de

2015-01-01

Nano-reinforced steels are considered for future nuclear reactors or for application at high temperature like the heat exchangers tubes or plates. Oxide Dispersion Strengthened (ODS) alloys are the most known of the nano-reinforced alloys. They exhibit high creep strength as well as high resistance to radiation damage. This article deals with the development of new nano reinforced alloys called Nitride Dispersed Strengthened (NDS). Those are also considered for nuclear applications and could exhibit higher ductility with a simplest fabrication way. Two main fabrication routes were studied: the co-milling of Fe–18Cr1W0.008N and TiH 2 powders and the plasma nitration at low temperature of a Fe–18Cr1W0.8Ti powder. The materials were studied mainly by Small Angle Neutron Scattering. The feasibility of the reinforcement by nano-nitride particles is demonstrated. The final size of the nitrides can be similar (few nanometers) to the nano-oxides observed in ODS alloys. The mechanical properties of the new NDS show an amazing ductility at high temperature for a nano-reinforced alloy

Development of new ferritic alloys reinforced by nano titanium nitrides

Energy Technology Data Exchange (ETDEWEB)

Mathon, M.H., E-mail: marie-helene.mathon@cea.fr [Laboratoire Léon Brillouin, CEA-CNRS, CEA/Saclay, 91191 Gif-sur-Yvette (France); Perrut, M., E-mail: mikael.perrut@onera.fr [Laboratoire Léon Brillouin, CEA-CNRS, CEA/Saclay, 91191 Gif-sur-Yvette (France); Poirier, L., E-mail: poirier@nitruvid.com [Bodycote France and Belgium, 9 r Jean Poulmarch, 95100 Argenteuil (France); Ratti, M., E-mail: mathieu.ratti@snecma.fr [CEA, DEN, Service de Recherches Métallurgiques Appliquées, F91191 Gif-sur-Yvette (France); Hervé, N., E-mail: nicolas.herve@cea.fr [CEA, DRT, LITEN, F38054 Grenoble (France); Carlan, Y. de, E-mail: yann.decarlan@cea.fr [CEA, DEN, Service de Recherches Métallurgiques Appliquées, F91191 Gif-sur-Yvette (France)

2015-01-15

Nano-reinforced steels are considered for future nuclear reactors or for application at high temperature like the heat exchangers tubes or plates. Oxide Dispersion Strengthened (ODS) alloys are the most known of the nano-reinforced alloys. They exhibit high creep strength as well as high resistance to radiation damage. This article deals with the development of new nano reinforced alloys called Nitride Dispersed Strengthened (NDS). Those are also considered for nuclear applications and could exhibit higher ductility with a simplest fabrication way. Two main fabrication routes were studied: the co-milling of Fe–18Cr1W0.008N and TiH{sub 2} powders and the plasma nitration at low temperature of a Fe–18Cr1W0.8Ti powder. The materials were studied mainly by Small Angle Neutron Scattering. The feasibility of the reinforcement by nano-nitride particles is demonstrated. The final size of the nitrides can be similar (few nanometers) to the nano-oxides observed in ODS alloys. The mechanical properties of the new NDS show an amazing ductility at high temperature for a nano-reinforced alloy.

Effect of the Preheating Temperature on Process Time in Friction Stir Welding of Al 6061-T6

DEFF Research Database (Denmark)

Jabbari, Masoud

2013-01-01

This paper presents the results obtained and the deductions made from an analytical modeling involving friction stir welding of Al 6061-T6. A new database was developed to simulate the contact temperature between the tool and the workpiece. A second-order equation is proposed for simulating...... the temperature in the contact boundary and the thermal history during the plunge phase. The effect of the preheating temperature on the process time was investigated with the proposed model. The results show that an increase of the preheating time leads to a decrease in the process time up to the plunge...

The effect of irradiation on the mechanical properties of 6061-T651 aluminum

International Nuclear Information System (INIS)

Alexander, D.J.

1992-01-01

Critical components of the Advanced Neutron Source (ANS) reactor, to be built at Oak Ridge National Laboratory (ORNL), will be fabricated from 6061-T651 aluminum alloy. This alloy has been selected for its favorable neutronic, thermal, and mechanical properties. The effect of irradiation on the tensile properties and fracture toughness has been studied to allow the lifetime of these components to be estimated. Irradiations were carried out in the High Flux Isotope Reactor at ORNL at a temperature of approximately 95 degree C to a fluence of approximately 10 26 m -2 (thermal). Testing was conducted from room temperature to 150 degree C. The yield and ultimate tensile strengths were increased by irradiation, and the total elongation decreased, but the fracture toughness at 26 and 95 degree C was not degraded by irradiation, and decreased only slightly at 150 degree C

Influence of ECAP temperature on the formability of a particle reinforced 2017 aluminum alloy

Science.gov (United States)

Wagner, S.; Härtel, M.; Frint, P.; F-X Wagner, M.

2017-03-01

Severe plastic deformation methods are commonly used to increase the strength of materials by generating ultrafine-grained microstructures. The application of these methods to Al-Cu alloys is, however, difficult because of their poor formability at room temperature. An additional reduction of formability of such alloys occurs when ceramic particles are added as reinforcement: this often triggers shear localization and crack initiation during ECAP. This is the main reason why equal-channel angular pressing (ECAP) of aluminum matrix composites (AMCs) can generally only be performed at elevated temperatures and using ECAP dies with a channel angle larger than 90° (e.g. 120°). In this study we present a brief first report on an alternative approach for the improvement of the formability of an AMC (AA2017, 10 % SiC): ECAP at low temperatures. We show that, using a temperature of -60 °C and a channel angle of 90° (corresponding to an equivalent strain of 1.1), ECAP of the AMC can be successfully performed without material failure. The mechanical properties of the strongly deformed AMC are analyzed by tensile testing. Our results indicate that the increased formability of the AMC at low temperatures can be attributed to the suppression of unstable plastic flow that affects formability at room temperature.

Microstructural and mechanical behaviors of nano-SiC-reinforced AA7075-O FSW joints prepared through two passes

Energy Technology Data Exchange (ETDEWEB)

Bahrami, Mohsen, E-mail: Mohsen.bahrami@aut.ac.ir [Faculty of Mining and Materials Engineering, Amirkabir University of Technology (AUT), Hafez Aveenue, Tehran (Iran, Islamic Republic of); Farahmand Nikoo, Mohsen [Faculty of Mining and Materials Engineering, Amirkabir University of Technology (AUT), Hafez Aveenue, Tehran (Iran, Islamic Republic of); Besharati Givi, Mohammad Kazem [Department of Mechanical Engineering, University of Tehran, Tehran (Iran, Islamic Republic of)

2015-02-25

In this paper, a threaded tapered pin tool was employed to fabricate a 2-pass friction stir welded (FSWed) joint. To investigate the benefits of nano-sized SiC particles on microstructural and mechanical properties of the joint, the experiment was repeated while SiC particles had been inserted along the joint line. In another joint, a square pin tool was applied in the second pass to evaluate the effectiveness of switching pin geometry between passes on the aforementioned properties. Microstructural features including grain size, second phase particles and reinforcement distribution were examined via optical and scanning electron microscopy (SEM) techniques. In addition to satisfactory connections between SiC particles and the matrix, the most homogenous particles distribution was observed in the specimen FSWed with both pin tools. This observation was further supported by atomic force microscopy (AFM) examination. Additionally, the foregoing joint demonstrated the maximum tensile strength which was synonymous with its smallest grain size. During tensile testing, SiC-free joint and SiC-reinforced ones fractured from stir zone (SZ) and base metal, respectively. Moreover, SiC-free joint showed necking phenomenon. SEM results showed that the SiC-reinforced specimens possessed ductile fracture morphologies. On the other hand, SiC-free specimen showed a quasi-cleavage fracture mode confirming its moderate percent elongation. In the meantime, SiC-reinforced specimens exhibited superior hardness level to SiC-free specimen.

Estudio microestructural y de resistencia de uniones soldadas de la aleación AW7020 por procedimiento MIG en función de la preparación de bordes

Directory of Open Access Journals (Sweden)

Bloem, Carlos Alberto

2000-02-01

Full Text Available Medium strength AW7XXX aluminium alloys are widely used as welded structures and in transportation. The applications of these alloys are limited by the behavior of the welded joints. There is not an agreement on the joint geometry that must be used on the 5 mm aluminium welds. The microhardness evolution is one of the most important strength indicator, For this reason, the aim of this work is to study the welded joint geometry influence on microhardness profile and on microstructure of a welded aluminium alloy AW7020 MIG, filled with AW5356.

Las aleaciones de aluminio de la serie AW7XXX de medias prestaciones se están empleando ampliamente en el sector del transporte, así como en la construcción de estructuras soldadas. La posibilidad de que estas aleaciones se empleen con mayor profusión está condicionada a un mayor conocimiento del comportamiento de la unión soldada. La evolución de la microdureza como un indicador de resistencia es ampliamente utilizado, pero no hay acuerdo sobre el efecto de la preparación de bordes previo a la soldadura y es por ello que el objetivo de este trabajo sea estudiar la influencia de la preparación de bordes sobre el perfil de microdureza y microestructura de la unión soldada de una aleación de aluminio AW7020, soldada mediante el proceso MIG, empleando como metal de aporte AW5356.

Development of non-dendritic microstructures in AA6061 cast billets

Energy Technology Data Exchange (ETDEWEB)

Zhang, X.-D.; Chadwick, T.A.; Bryant, J.D. [Reynolds Metals Co., Chester, VA (United States)

2000-07-01

Non-dendritic structures have been shown to have many advantages over conventional, dendritic structures in castable aluminum alloys. Examples include high structural integrity, reduced porosity, excellent formability and enhanced near net-shape forming capability. Non-dendritic materials are characterized by an equiaxed, globularized grain structure. Previous work has focused on the application of these structures in traditional casting alloys such as A356 and A357, and on the processing of these alloys during semi-solid forming and squeeze casting. There is considerably less information on the impact of non-dendritic microstructures upon solid state deformation, and the use of such microstructures in the processing of traditional wrought aluminum alloys. In this paper, we will present our recent work in casting non-dendritic AA6061 alloy using different techniques, and discuss the effects of cast structure on deformation behavior during solid state processing at elevated temperatures. Cast microstructures were modified during direct chill casting using three different methods: magneto-hydrodynamic (MHD) agitation, mechanical stirring, and high loadings of grain refiner. A detailed microstructure characterization will be presented and discussed in terms of structural integrity, grain morphology, and their effects on deformation in the solid state. (orig.)

Women's Stereotypic Roles: A Replication and Standardization of the AWS and PAQ for Selected Ethnic Groups.

Science.gov (United States)

Wheeler, Edwin E.; And Others

A replication of two previous studies, this study examined the effect of both sex and ethnicity on attitudes toward women, self-reported masculinity-femininity, and masculine-feminine stereotypic attitudes. The Attitudes Toward Women Scale (AWS) and the Personal Attributes Questionnaire (PAQ) were administered to 367 college students (112 Anglos,…

Tensile strength and fatigue strength of 6061 aluminum alloy friction welded joints

Energy Technology Data Exchange (ETDEWEB)

Ochi, H.; Tsujino, R. [Osaka Inst. of Tech., Asahi-ku Osaka (Japan); Sawai, T. [Osaka Sangyo Univ., Daito (Japan); Yamamoto, Y. [Setsunan Univ., Neyagawa (Japan); Ogawa, K. [Osaka Prefecture Univ., Sakai (Japan); Suga, Y. [Keio Univ., Kohoku-ku, Yokohama (Japan)

2002-07-01

Friction welding of 6061 aluminum alloy was carried out in order to examine the relationship between deformation heat input in the upset stage and joint performance. The joint performance was evaluated by tensile testing and fatigue testing. Stabilized tensile strength was obtained when the deformation heat input in the upset stage exceeded 200 J/s. Weld condition at the weld interface and the width of softened area affected fatigue strength more than tensile strength. That is, when the weld condition at the weld interface is good and the softened area is wide, fatigue strength increases. On the other hand, when the weld condition at the weld interface is good and the softened area is narrow, and when the weld condition at the weld interface is somewhat poor in spite of the wide softened area, fatigue strength decreases. The fatigue limit obtained by the fatigue testing revealed that, when the deformation heat input in the upset stage exceeded a certain value, sound joints could be produced. (orig.)

Simulation of the repeated waterdrop impact onto the AL6061-T6

Energy Technology Data Exchange (ETDEWEB)

Cho, Ji Ryong [Inje University, Kimhae (Korea, Republic of)

2015-09-15

Waterdrop impact effects on mechanical and aerospace components have presented challenging problems for investigation. Sometimes it erodes the surface and leads to failure of the components. But it is known that controlled impact can enhance the fatigue life of the components. In this computational study, residual effects of repeated waterdrop impact onto the AL6061-T6 specimen are investigated. It is shown that above a critical impact speed (74 m/s), residual compressive stress zone is built up underneath the impact surface as a result of the plastic deformation of the specimen. The depth of pit due to the plastic deformation increases with the impact speed and the accumulated number of impact. At the impact speed of 500 m/s, after 4 impacts, the maximum residual compressive stress of 0.345 GPa is obtained at 0.067 mm underneath the surface, and the depth of the compressive stress zone is 0.2 mm.

Braided reinforced composite rods for the internal reinforcement of concrete

Science.gov (United States)

Gonilho Pereira, C.; Fangueiro, R.; Jalali, S.; Araujo, M.; Marques, P.

2008-05-01

This paper reports on the development of braided reinforced composite rods as a substitute for the steel reinforcement in concrete. The research work aims at understanding the mechanical behaviour of core-reinforced braided fabrics and braided reinforced composite rods, namely concerning the influence of the braiding angle, the type of core reinforcement fibre, and preloading and postloading conditions. The core-reinforced braided fabrics were made from polyester fibres for producing braided structures, and E-glass, carbon, HT polyethylene, and sisal fibres were used for the core reinforcement. The braided reinforced composite rods were obtained by impregnating the core-reinforced braided fabric with a vinyl ester resin. The preloading of the core-reinforced braided fabrics and the postloading of the braided reinforced composite rods were performed in three and two stages, respectively. The results of tensile tests carried out on different samples of core-reinforced braided fabrics are presented and discussed. The tensile and bending properties of the braided reinforced composite rods have been evaluated, and the results obtained are presented, discussed, and compared with those of conventional materials, such as steel.

Stanisław Barańczak i awangarda

Directory of Open Access Journals (Sweden)

Alina Świeściak

2016-12-01

Full Text Available The poetry of Stanisław Barańczak, who himself was against historical avant-garde as a movement that abandoned ethical commitments, has quite a lot in common with avant-garde. Like other New Wave artists, his poetry can be read in the context of the neo-avant-garde and counterculture, e.g. in the context of Guy Debord’s The Society of the Spectacle and Herbert Marcuse’s Onedimensional Man, with the propositions that overlap in many places with those of Baranczak’s “dialectic Romanticism”. When analysing the links of this poetry with the participant art of the 1960s and 1970s, it can be concluded that new-wave commitment has little in common with the typical attempts of the neo-avant-garde at regaining privacy, since the political character of Barańczak’s poetry is based on giving a position of privilege to the martyrdom code of Polish romanticism, which he frames in elitist modernist language.

The corrosion protection of 6061-T6 aluminum by a polyurethane-sealed anodized coat

Science.gov (United States)

Danford, M. D.

1990-01-01

The corrosion protection of 6061-T6 anodized aluminum afforded by a newly patented polyurethane seal was studied using the ac impedance technique. Values of the average corrosion rates over a 27-day exposure period in 3.5 percent NaCl solutions at pH 5.2 and pH 9.5 compared very favorably for Lockheed-prepared polyurethane-sealed and dichromate-sealed coats of the same thickness. Average corrosion rates for both specimens over the first 7 days of exposure compared well with those for a hard anodized, dichromate-sealed coat, but rose well above those for the hard anodized coat over the entire 27-day period. This is attributed both to the greater thickness of the hard anodized coat, and possibly to its inherently better corrosion protective capability.

Mechanical properties of nanodiamond-reinforced hydroxyapatite composite coatings deposited by suspension plasma spraying

Science.gov (United States)

Chen, Xiuyong; Zhang, Botao; Gong, Yongfeng; Zhou, Ping; Li, Hua

2018-05-01

Hydroxyapatite (HA) coatings suffer from poor mechanical properties, which can be enhanced via incorporation of secondary bioinert reinforcement material. Nanodiamond (ND) possesses excellent mechanical properties to play the role as reinforcement for improving the mechanical properties of brittle HA bioceramic coatings. The major persistent challenge yet is the development of proper deposition techniques for fabricating the ND reinforced HA coatings. In this study, we present a novel deposition approach by plasma spraying the mixtures of ND suspension and micron-sized HA powder feedstock. The effect of ND reinforcement on the microstructure and the mechanical properties of the coatings such as hardness, adhesive strength and friction coefficient were examined. The results showed that the ND-reinforced HA coatings display lower porosity, fewer unmelted particles and uniform microstructure, in turn leading to significantly enhanced mechanical properties. The study presented a promising approach to fabricate ND-reinforced HA composite coatings on metal-based medical implants for potential clinical application.

Pro Memoria. Professor Bolesław Jałowy (1906-1943): Mortui viventes obligant - the livings are obligated to the dead.

Science.gov (United States)

Wincewicz, Andrzej

2016-01-01

Professor Bolesław Jałowy (1906-1943) was a chairman of Department of Histology and Embryology at Faculty of Medicine of King John Casimir University (Polish: Universytet Jana Kazimierza: UJK) in Lvov. He succeeded Professor Władysław Szymonowicz (1869-1939) who held this position for decades. As the most skillful followers of his tutor, Bolesław Jałowy was a great investigator of physiology of human tissue, embryogenesis, histological consequences of female sex hormones on blood clotting action as well as regeneration of nerves in addition to description of silver staining technique for reticulin fibers of skin. He was a hard working person with gentle attitude to such a subtle matter as microscopic structure of human body. However, he happened to live in brutal conditions of nationalistic struggles. His example shows how much a dedicated scientist could do in a very short time as his life was tragically ended with murdering him during World War Two. His story is a great lesson for generations of academic workers how to meet high moral standards with efficient and creative scientific work in evil and destructive, nationalistic climate that occurs usually in wartime.

Flexural reinforced concrete member with FRP reinforcement

OpenAIRE

Putzolu, Mariana

2017-01-01

One of the most problematic point in construction is the durability of the concrete especially related to corrosion of the steel reinforcement. Due to this problem the construction sector, introduced the use of Fiber Reinforced Polymer, the main fibers used in construction are Glass, Carbon and Aramid. In this study, the author aim to analyse the flexural behaviour of concrete beams reinforced with FRP. This aim is achieved by the analysis of specimens reinforced with GFRP bars, with theoreti...

The reception of Czesław Miłosz’s poetry by students of primary, lower secondary and upper secondary schools

Directory of Open Access Journals (Sweden)

Angelika Matuszek

2013-09-01

Full Text Available The works of Czesław Miłosz are usually regarded as “especially difficult” literature. It is therefore important to examine how young people analyse and interpret selected works of the poet. The article presents the results of a study evaluating the quality of reception of Miłosz’s poetry by students at all levels of compulsory education prior to the Czesław Miłosz Year in 2011. The study enabled the assessment of students’ knowledge of the life and work of Miłosz and the reading competencies required by a modern student to analyse and interpret his literary work.

A method for calculating equivalent diameter of fiber in self-compacting fiber reinforced concrete

NARCIS (Netherlands)

Yu, R.; Spiesz, P.R.; Brouwers, H.J.H.; Fischer, H.-B.; Bode, K.-A.; Beuthan, C.

2012-01-01

This paper presents a method for calculating the equivalent diameter of fiber in self-compacting fiber reinforced concrete (SCFRC). The key idea is to utilize a small amount of particles with a narrow particle size distribution to replace the fibers by the same volume, without causing any obvious

Effect of particle size and concentration on the mechanical properties of polyester/date palm seed particulate composites

Directory of Open Access Journals (Sweden)

Alewo Opuada AMEH

2015-05-01

Full Text Available The use of cellulosic materials as reinforcement in composites can greatly enhance their properties. The thrust of this study was to investigate the effect of date palm seed particle on the properties of reinforced polyester. Unsaturated polyester resin was reinforced with date palm seed particles of 0.5, 2.0 and 2.8mm particle sizes using variable particle loadings of 5, 10, 15, 20 and 25wt%. The composites obtained were subjected to various types of mechanical and physical tests in order to assess their performance. The optimum tensile strength of 16.7619N/mm2 and elastic modulus of 343.8N/mm2 were attained at 15wt% and 10wt% loading (using 0.5mm particles respectively and percent water absorption was found to be least for 0.5mm particle size. The hardness was enhanced to the maximum of 74 HRF (Rockwell Hardness Factor by 2mm particle size at 25wt% loading. Pure unsaturated polyester resin recorded tensile strength of 17.5959N/mm2, elastic modulus of 316.7N/mm2 and hardness of 33.5 HRF. The results indicated that the use of date palm seed particles as reinforcement can enhance the properties of polyester composites.

Preparation of curcumin nanoparticle by using reinforcement ionic gelation technique

Science.gov (United States)

Suryani, Halid, Nur Hatidjah Awaliyah; Akib, Nur Illiyyin; Rahmanpiu, Mutmainnah, Nina

2017-05-01

Curcumin, a polyphenolic compound present in curcuma longa has a wide range of activities including anti-inflammatory properties. The potency of curcumin is limited by its poor oral bioavailability because of its poor solubility in aqueous. Various methods have been tried to solve the problem including its encapsulation into nanoparticle. The aim of this study is to develop curcumin nanoparticle by using reinforcement ionic gelation technique and to evaluate the stability of curcumin nanoparticles in gastrointestinal fluid. Curcumin nanoparticles were prepared by using reinforcement ionic gelation technique with different concentrations of chitosan, trypolyphosphate, natrium alginate and calcium chloride. Curcumin nanoparticles were then characterized including particle size and zeta potential by using particle size analyzer and morphology using a transmission electron microscope, entrapment efficiency using UV-Vis Spectrophotometer and chemical structure analysis by Infra Red Spectrophotometer (FTIR). Furthermore, the stability of curcumin nanoparticles were evaluated on artificial gastric fluid and artificial intestinal fluids by measuring the amount of curcumin released in the medium at a time interval. The result revealed that curcumin nanoparticles can be prepared by reinforcement ionic gelation technique, the entrapment efficiency of curcumin nanoparticles were from 86.08 to 91.41%. The average of particle size was 272.9 nm and zeta potential was 12.05 mV. The morphology examination showed that the curcumin nanoparticles have spherical shape. The stability evaluation of curcumin nanoparticles showed that the nanoparticles were stable on artificial gastric fluid and artificial intestinal fluid. This result indicates that curcumin nanoparticles have the potential to be developed for oral delivery.

Machinability study of Al-TiC metal matrix composite

Directory of Open Access Journals (Sweden)

Siddappa P. N.

2018-01-01

Full Text Available Aluminum Metal Matrix Composites have emerged as an advanced class of structural materials have a combination of different, superior properties compared to an unreinforced matrix, which can result in a number of service benefits such as increased strength, higher elastic moduli, higher service temperature, low CTE, improved wear resistance, high toughness, etc. The excellent mechanical properties of these materials together with weight saving makes them very attractive for a variety of engineering applications in aerospace, automotive, electronic industries, etc. Hence, these materials provide as alternative substitutes for conventional engineering materials when specific mechanical properties necessary for required applications. In this work an attempt is made to study the machining parameters of Al6061/TiC MMC. The composite is developed by reinforcing TiC particles in varying proportions of 3, 6, 9 and 12 % weight fractions to the Al6061 matric alloy through stir casting technique. Cutting forces were measured by varying cutting speed and feed rate with constant depth of cut for different % weight fractions. The results showed that the cutting force increases with the increase of feed rate and decreases with the increase of cutting speed for all the weight fractions. Cutting parameters were optimized using Taguchi technique.

Mechanical behavior and wear prediction of stir cast Al–TiB2 composites using response surface methodology

International Nuclear Information System (INIS)

Suresh, S.; Shenbaga Vinayaga Moorthi, N.; Vettivel, S.C.; Selvakumar, N.

2014-01-01

Graphical abstract: - Highlights: • Various experiments were conducted on Al6061–TiB 2 composite. • XRD and EDS studies confirm the crystalline size and elements present. • SEM, EDS and OM observations were used to study the characteristics. • Curve fitting and RSM design methods are effectively used to develop the model. - Abstract: Al6061 was reinforced with various percentages of TiB 2 particles by using high energy stir casting method. The characterization was performed through X-ray Diffraction, Energy Dispersive Spectrum and Scanning Electron Microscope. The mechanical behaviors such as hardness, tensile strength and tribological behavior were investigated. Wear experiments were conducted by using a pin-on-disc wear tester at varying load. The curve fitting technique was used to develop the respective polynomial and power law equations. The wear mechanism of the specimen was studied through SEM. Response Surface Methodology was used to minimize the number of experimental conditions and develop the mathematical models between the key process parameters namely weight percentage of TiB 2 , load and sliding distance. Analysis of Variance technique was applied to check the validity of the developed model. The mathematical model developed for the specific wear rate was predicted at 99.5% confidence level and some useful conclusions were made

On the hot cracking susceptibility of a semisolid aluminium 6061 weld: Application of a coupled solidification- thermomechanical model

International Nuclear Information System (INIS)

Rajani, H R Zareie; Phillion, A B

2015-01-01

A coupled solidification-thermomechanical model is presented that investigates the hot tearing susceptibility of an aluminium 6061 semisolid weld. Two key phenomena are considered: excessive deformation of the semisolid weld, initiating a hot tear, and the ability of the semisolid weld to heal the hot tear by circulation of the molten metal. The model consists of two major modules: weld solidification and thermomechanical analysis. 1) By means of a multi-scale model of solidification, the microstructural evolution of the semisolid weld is simulated in 3D. The semisolid structure, which varies as a function of welding parameters, is composed of solidifying grains and a network of micro liquid channels. The weld solidification module is utilized to obtain the solidification shrinkage. The size of the micro liquid channels is used as an indicator to assess the healing ability of the semisolid weld. 2) Using the finite element method, the mechanical interaction between the weld pool and the base metal is simulated to capture the transient force field deforming the semisolid weld. Thermomechanical stresses and shrinkage stresses are both considered in the analysis; the solidification contractions are extracted from the weld solidification module and applied to the deformation simulation as boundary conditions. Such an analysis enables characterization of the potential for excessive deformation of the weld. The outputs of the model are used to study the effect of welding parameters including welding current and speed, and also welding constraint on the hot cracking susceptibility of an aluminium alloy 6061 semisolid weld. (paper)

Enhanced mechanical properties of ARB-processed aluminum alloy 6061 sheets by subsequent asymmetric cryorolling and ageing

International Nuclear Information System (INIS)

Yu, Hailiang; Su, Lihong; Lu, Cheng; Tieu, Kiet; Li, Huijun; Li, Jintao; Godbole, Ajit; Kong, Charlie

2016-01-01

Grain size and precipitations affect the strength and ductility of ultrafine-grained materials. In this study, aluminum alloy 6061 sheets were fabricated using the accumulative roll bonding (ARB) technique. The ARB-processed sheets were subsequently subjected to cryorolling and asymmetric cryorolling. The sheets were further aged at 100 °C for 48 h. Mechanical tests show that a combination of asymmetric cryorolling and ageing results in significant improvement in both the ductility and the strength of the ARB-processed sheets. The microstructures of the sheets at different stages of the process were also analyzed using optical microscopy, scanning electron microscopy, transmission electron microscopy and X-ray diffraction in order to correlate the mechanical properties with the microstructure.

Enhanced mechanical properties of ARB-processed aluminum alloy 6061 sheets by subsequent asymmetric cryorolling and ageing

Energy Technology Data Exchange (ETDEWEB)

Yu, Hailiang, E-mail: hailiang@uow.edu.au [State Key Laboratory of High Performance Complex Manufacturing, Central South University, Changsha 410083 (China); School of Mechanical, Materials & Mechatronics Engineering, University of Wollongong, NSW 2500 (Australia); Su, Lihong; Lu, Cheng; Tieu, Kiet [School of Mechanical, Materials & Mechatronics Engineering, University of Wollongong, NSW 2500 (Australia); Li, Huijun, E-mail: huijun@uow.edu.au [School of Mechanical, Materials & Mechatronics Engineering, University of Wollongong, NSW 2500 (Australia); Li, Jintao; Godbole, Ajit [School of Mechanical, Materials & Mechatronics Engineering, University of Wollongong, NSW 2500 (Australia); Kong, Charlie [Electron Microscope Unit, University of New South Wales, Sydney, NSW 2052 (Australia)

2016-09-30

Grain size and precipitations affect the strength and ductility of ultrafine-grained materials. In this study, aluminum alloy 6061 sheets were fabricated using the accumulative roll bonding (ARB) technique. The ARB-processed sheets were subsequently subjected to cryorolling and asymmetric cryorolling. The sheets were further aged at 100 °C for 48 h. Mechanical tests show that a combination of asymmetric cryorolling and ageing results in significant improvement in both the ductility and the strength of the ARB-processed sheets. The microstructures of the sheets at different stages of the process were also analyzed using optical microscopy, scanning electron microscopy, transmission electron microscopy and X-ray diffraction in order to correlate the mechanical properties with the microstructure.

Ultrasonic Examination of Double-Shell Tank 214-AW-102 Knuckle Region. Examination completed February 2003

International Nuclear Information System (INIS)

Pardini, Allan F.; Posakony, Gerald J.

2003-01-01

COGEMA Engineering Corporation (COGEMA), under a contract from CH2M Hill Hanford Group (CH2M Hill), has performed an ultrasonic examination of the knuckle region of Double-Shell Tank 241-AW-102 utilizing the Remotely Operated Nondestructive Examination (RONDE) system. The purpose of this examination was to provide information that could be used to evaluate the integrity of the knuckle region of the primary tank. The requirements for the ultrasonic examination of Tank 241-AW-102 were to detect, characterize (identify, size, and locate), and record measurements made of any circumferentially oriented cracks that might be present in the knuckle area of the primary tank. Any measurements that exceed the requirements set forth in the Engineering Task Plan (ETP), RPP-7869, are reported to CH2M Hill and the Pacific Northwest National Laboratory (PNNL) for further evaluation. Under the contract with CH2M Hill, all data is to be recorded on disk and paper copies of all measurements are provided t o PNNL for third-party evaluation. PNNL is responsible for preparing a report(s) that describes the results of the COGEMA ultrasonic examinations

Experimental data on the properties of natural fiber particle reinforced polymer composite material.

Science.gov (United States)

Chandramohan, D; Presin Kumar, A John

2017-08-01

This paper presents an experimental study on the development of polymer bio-composites. The powdered coconut shell, walnut shells and Rice husk are used as reinforcements with bio epoxy resin to form hybrid composite specimens. The fiber compositions in each specimen are 1:1 while the resin and hardener composition 10:1 respectively. The fabricated composites were tested as per ASTM standards to evaluate mechanical properties such as tensile strength, flexural strength, shear strength and impact strength are evaluated in both with moisture and without moisture. The result of test shows that hybrid composite has far better properties than single fibre glass reinforced composite under mechanical loads. However it is found that the incorporation of walnut shell and coconut shell fibre can improve the properties.

Development of the electron beam welding of the aluminium alloy 6061-T6 for the Jules Horowitz reactor

International Nuclear Information System (INIS)

Leblanc, Y.

2013-01-01

The aluminium alloy 6061-T6 has been selected for the construction of the Jules Horowitz's reactor vessel. This reactor vessel is pressurized and will be made through butt welding of ∼ 2 cm thick aluminium slabs. The electron beam welding process has been tested and qualified. It appears that this welding process allows: -) welding without pre-heating, -) vacuum welding, -) welding of 100% of the thickness in one passage, -) very low deforming welding process, -) very low density and very low volume of blow holes, -) weak ZAT (Thermal Affected Zones), and -) high reproducibility that permits automation. (A.C.)

Improving the corrosion resistance of AZ91D magnesium alloy through reinforcement with titanium carbides and borides

OpenAIRE

Gobara, Mohamed; Shamekh, Mohamed; Akid, Robert

2015-01-01

A composite consisting of magnesium matrix reinforced with a network of TiC–Ti2AlC–TiB2 particulates has been fabricated using a practical in-situ reactive infiltration technique. The microstructural and phase composition of the magnesium matrix composite (R-Mg) was investigated using SEM/EDS and XRD. The analyses revealed the complete formation of TiC, Ti2AlC and TiB2 particles in the magnesium matrix. Comparative compression tests of R-Mg and AZ91D alloy showed that the reinforcing particle...

Continuous EB welding of the reinforcement of the CMS conductor

CERN Document Server

Folch, R; Campi, D; Christin, R; Creton, J P; Curé, B; Hervé, A; Horváth, I L; Neuenschwander, J; Riboni, P; Sequeira-Lopes-Tavares, S; Sgobba, Stefano

2002-01-01

The Compact Muon Solenoid (CMS) is one of the general-purpose detectors to be provided for the LHC project at CERN. The design field of the CMS superconducting magnet is 4 T, the magnetic length is 12.5 m and the free bore is 6 m. In order to withstand the electro-mechanical forces during the operation of the CMS magnet, the superconducting cable embedded in a 99.998% pure aluminum matrix is reinforced with two sections of aluminum alloy EN AW-6082 assembled by continuous Electron Beam Welding (EBW). A dedicated production line has been designed by Techmeta, a leading company in the field of EBW. The production line has a total length of 70 m. Non-stop welding of each of the 20 lengths of 2.5 km, required to build the coil, will last 22 hours. EBW is the most critical process involved in the production line. The main advantage of the EBW process is to minimize the Heat Affected Zone; this is particularly important for avoiding damage to the superconducting cable located only 4.7 mm from the welded joints. Two...

The determination of the local conditions for void initiation in front of a crack tip for materials with second-phase particles

Energy Technology Data Exchange (ETDEWEB)

Sabirov, I. [Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Jahnstrasse 12, A-8700 Leoben (Austria)]. E-mail: sabirov@unileoben.ac.at; Duschlbauer, D. [Institute of Lightweight Design and Structural Biomechanics, Vienna University of Technology, Gusshausstrasse 27-29, A-1040 Vienna (Austria); Pettermann, H.E. [Institute of Lightweight Design and Structural Biomechanics, Vienna University of Technology, Gusshausstrasse 27-29, A-1040 Vienna (Austria); Kolednik, O. [Erich Schmid Institute of Materials Science, Austrian Academy of Sciences, Jahnstrasse 12, A-8700 Leoben (Austria)

2005-02-25

A procedure is proposed to determine, for second-phase particles near a crack tip, the maximum particle stresses at the moment of void initiation by either particle fracture or particle/matrix interface separation. A digital image analysis system is applied to perform a quantitative analysis of corresponding fracture surface regions from stereo image pairs taken in the scanning electron microscope. The fracture surface analysis is used to measure, for individual particles, the crack tip opening displacement at the moment of void initiation and the particle location with respect to the crack tip. From these data, the stress tensor at the moment of void initiation is calculated from the Hutchinson-Rice-Rosengren (HRR) field theory. The corresponding average local stresses within the particle are evaluated by a non-linear Mori-Tanaka-type approach. These stresses are compared to estimates according to the models by Argon et al. [A.S. Argon, J. Im, R. Safoglu, Metall. Trans. 6 (1975) 825] and Beremin [F.M. Beremin, Metall. Trans. 12 (1981) 723]. The procedure is demonstrated on an Al6061-10% Al{sub 2}O{sub 3} metal matrix composite.

Study on reinforced concrete beams with helical transverse reinforcement

Science.gov (United States)

Kaarthik Krishna, N.; Sandeep, S.; Mini, K. M.

2018-02-01

In a Reinforced Concrete (R.C) structure, major reinforcement is used for taking up tensile stresses acting on the structure due to applied loading. The present paper reports the behavior of reinforced concrete beams with helical reinforcement (transverse reinforcement) subjected to monotonous loading by 3-point flexure test. The results were compared with identically similar reinforced concrete beams with rectangular stirrups. During the test crack evolution, load carrying capacity and deflection of the beams were monitored, analyzed and compared. Test results indicate that the use of helical reinforcement provides enhanced load carrying capacity and a lower deflection proving to be more ductile, clearly indicating the advantage in carrying horizontal loads. An analysis was also carried out using ANSYS software in order to compare the test results of both the beams.

Plasma electrolytic oxidation of AMCs

Science.gov (United States)

Morgenstern, R.; Sieber, M.; Lampke, T.

2016-03-01

Aluminum Matrix Composites (AMCs) consisting of high-strength alloys and ceramic reinforcement phases exhibit a high potential for security relevant lightweight components due to their high specific mechanical properties. However, their application as tribologically stressed components is limited because of their susceptibility against fatigue wear and delamination wear. Oxide ceramic protective coatings produced by plasma electrolytic oxidation (PEO) can solve these problems and extend the possible applications of AMCs. The substrate material was powder metallurgically processed using alloy EN AW 2017 and SiC or Al2O3 particles. The influence of material properties like particle type, size and volume fraction on coating characteristics is clarified within this work. An alkaline silicate electrolyte was used to produce PEO coatings with technically relevant thicknesses under bipolar-pulsed current conditions. Coating properties were evaluated with regard to morphology, chemical composition, hardness and wear resistance. The particle type proved to have the most significant effect on the coating properties. Whereas compactness and thickness are not deteriorated by the incorporation of thermodynamically stable alumina particles, the decomposition of silica particles during the PEO processes causes an increase of the porosity. The higher silica particle content decreases also the coating thickness and hardness, which leads in particular to reduction of the wear resistance of the PEO coatings. Finally, different approaches for the reduction of the coating porosity of silica reinforced AMCs are discussed.

Structure/property relations of aluminum under varying rates and stress states

Energy Technology Data Exchange (ETDEWEB)

Tucker, Matthew T [Los Alamos National Laboratory; Horstemeyer, Mark F [MISSISSIPPI STATE UNIV; Whittington, Wilburn R [MISSISSIPPI STATE UNIV; Solanki, Kiran N [MISSISSIPPI STATE UNIV.

2010-11-19

In this work we analyze the plasticity, damage, and fracture characteristics of three different processed aluminum alloys (rolled 5083-H13, cast A356-T6, and extruded 6061-T6) under varying stress states (tension, compression, and torsion) and strain rates (0.001/, 1/s., and 1000/s). The stress state difference had more of a flow stress effect than the applied strain rates for those given in this study (0.001/sec up to 1000/sec). The stress state and strain rate also had a profound effect on the damage evolution of each aluminum alloy. Tension and torsional straining gave much greater damage nucleation rates than compression. Although the damage of all three alloys was found to be void nucleation dominated, the A356-T6 and 5083-H131 aluminum alloys incurred void damage via micron scale particles where the 6061-T6 aluminum alloy incurred void damage from two scales, micron-scale particles and nanoscale precipitates. Having two length scales of particles that participated in the damage evolution made the 6061-T6 incur a strain rate sensitive damage rate that was different than the other two aluminum alloys. Under tension, as the strain rate increased, the 6061-T6 aluminum alloy's void nucleation rate decreased, but the A356-T6 and 5083-H131 aluminum alloys void nucleation rate increased.

Experimental data on the properties of natural fiber particle reinforced polymer composite material

Directory of Open Access Journals (Sweden)

D. Chandramohan

2017-08-01

Full Text Available This paper presents an experimental study on the development of polymer bio-composites. The powdered coconut shell, walnut shells and Rice husk are used as reinforcements with bio epoxy resin to form hybrid composite specimens. The fiber compositions in each specimen are 1:1 while the resin and hardener composition 10:1 respectively. The fabricated composites were tested as per ASTM standards to evaluate mechanical properties such as tensile strength, flexural strength, shear strength and impact strength are evaluated in both with moisture and without moisture. The result of test shows that hybrid composite has far better properties than single fibre glass reinforced composite under mechanical loads. However it is found that the incorporation of walnut shell and coconut shell fibre can improve the properties.

The Relationship between Zhedanov's Algebra AW(3) and the Double Affine Hecke Algebra in the Rank One Case

NARCIS (Netherlands)

Koornwinder, T.H.

2007-01-01

Vadim Kuznetsov Memorial Issue on Integrable Systems and Related Topics Abstract Zhedanov's algebra AW(3) is considered with explicit structure constants such that, in the basic representation, the first generator becomes the second order q-difference operator for the Askey-Wilson polynomials. It is

Improving the particle distribution and mechanical properties of friction-stir-welded composites by using a smooth pin tool

Science.gov (United States)

Liu, Huijie; Hu, Yanying; Zhao, Yunqiang; Fujii, Hidetoshi

2017-09-01

Friction stir welding (FSW) is a very promising technique for joining particle-reinforced aluminum-matrix composites (PRAMCs), but with increase in the volume fraction of reinforcing particles, their distribution in welds becomes inhomogeneous. This leads to an inconsistent deformation of welds and their destruction at low stresses. In order to improve the weld microstructure, a smooth pin tool was used for the friction stir welding of AC4A + 30 vol.% SiC particle-reinforced aluminum-matrix composites. The present work describes the effect of welding parameters on the characteristics of particle distribution and the mechanical properties of welds. The ultimate strength of weld reached, 309 MPa, was almost 190% of that of the basic material. The mechanism of SiC particle conglomeration is clearly illustrated by means of schematic illustrations.

Evaluation of the Technical-Economic Potential of Particle- Reinforced Aluminum Matrix Composites and Electrochemical Machining

International Nuclear Information System (INIS)

Schubert, A; Hackert-Oschätzchen, M; Lehnert, N; Götze, U; Herold, F; Schmidt, A; Meichsner, G

2016-01-01

Compared to conventional cutting, the processing of materials by electrochemical machining offers some technical advantages like high surface quality, no thermal or mechanical impact on the work piece and preservation of the microstructure of the work piece material. From the economic point of view, the possibility of process parallelization and the absence of any process-related tool wear are mentionable advantages of electrochemical machining. In this study, based on experimental results, it will be evaluated to what extent the electrochemical machining is technically and economically suitable for the finish-machining of particle- reinforced aluminum matrix composites (AMCs). Initial studies showed that electrochemical machining - in contrast to other machining processes - has the potential to fulfil demanding requirements regarding precision and surface quality of products or components especially when applied to AMCs. In addition, the investigations show that processing of AMCs by electrochemical machining requires less energy than the electrochemical machining of stainless steel. Therefore, an evaluation of electrochemically machined AMCs - compared to stainless steel - from a technical and an economic perspective will be presented in this paper. The results show the potential of electro-chemically machined AMCs and contribute to the enhancement of instruments for technical-economic evaluations as well as a comprehensive innovation control. (paper)

[Case of awake intubation in semi-sitting position for a patient with myasthenia gravis combined with cervical disc hernia utilizing Pentax-AWS Airwayscope].

Science.gov (United States)

Komasawa, Nobuyasu; Ueki, Ryusuke; Tomita, Yukihiko; Kaminoh, Yoshiroh; Tashiro, Chikara

2011-01-01

We report a case of awake intubation utilizing Pentax-AWS Airwayscope in semi-sitting position. A 74-year-old man with myasthenia gravis and cervical disc hernia was scheduled for distal gastrectomy under general anesthesia. He could not move his head due to severe cervical disc hernia and also could not sufficiently breathe due to the fatigue of respiratory muscles by myasthenia gravis in supine position. With fentanyl bolus administration and lidocaine spray for laryngotracheal anesthesia, we performed awake intubation in semi-sitting position with AWS from cranial side. The patient did not buck during intubation and no hemodynamic change was observed.

Preparation and biocompatibility of poly (methyl methacrylate reinforced with bioactive particles

Directory of Open Access Journals (Sweden)

Pereira Marivalda de Magalhães

2003-01-01

Full Text Available Calcium phosphates and bioactive glasses have been used in many biomedical applications for more than 30 years due basically to their bioactive behavior. However, ceramics are too brittle for applications that require high levels of toughness and easy processability. In this work, a biphasic calcium phosphate (BCP and a bioactive glass composition (BG were combined with polymers to produce composites with tailorable properties and processability. The BCP particles were synthesized by a precipitation technique. The BG particles were produced by sol-gel processing. The BCP particles were treated with a silane agent to improve the compatibility between particles and the polymer matrix. Dense samples were produced by hot pressing (200 °C a mixture of 30 wt.% of particles in poly (methyl methacrylate. The samples produced were characterized by X-ray diffraction, infrared spectroscopy and scanning electron microscopy. Mechanical properties were evaluated by a three point bending test. Samples were also submitted to in vitro bioactivity test and in vivo toxicity test. Results showed that the production of the composites was successfully achieved, yielding materials with particles well dispersed within the matrices. Evaluation of the in vivo inflammatory response showed low activity levels for all composites although composites with silane treated BCP particles led to milder inflammatory responses than composites with non-treated particles.

REINFORCED COMPOSITE PANEL

DEFF Research Database (Denmark)

2003-01-01

A composite panel having front and back faces, the panel comprising facing reinforcement, backing reinforcement and matrix material binding to the facing and backing reinforcements, the facing and backing reinforcements each independently comprising one or more reinforcing sheets, the facing rein...... by matrix material, the facing and backing reinforcements being interconnected to resist out-of-plane relative movement. The reinforced composite panel is useful as a barrier element for shielding structures, equipment and personnel from blast and/or ballistic impact damage....

Energy management: analysis of reducing energy consumption by sectors of the A.W. Faber-Castell S.A. company; Gerenciamento energetico: analise de reducao do consumo de energia eletrica de setores da empresa A.W. Faber-Castell S.A.

Energy Technology Data Exchange (ETDEWEB)

Silva, Jesue Ferraz da [Faculdades Integradas de Sao Carlos (FADISC), SP (Brazil); Branco, Fabio Jose Ceron [Universidade de Sao Paulo (EESC/USP), Sao Carlos, SP (Brazil). Escola de Engenharia

2009-07-01

The energy consumption in the sectors that require a lot of input from the company A.W. Faber-Castell S.A. after the implementation of the program to reduce energy consumption by the Internal Committee for Energy Conservation was studied. This program aimed to reduce by 0.5% of electric power in the company.

Dissimilar friction stir welding of 6061 Al to T2 pure Cu adopting tooth-shaped joint configuration: Microstructure and mechanical properties

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wei; Shen, Yifu, E-mail: yfshen_nuaa@hotmail.com; Yan, Yinfei; Guo, Rui

2017-04-06

In this paper, dissimilar 6061aluminum alloy and commercial pure copper were friction stir butt welded adopting tooth-shaped joint configuration to investigate the influence of Al/Cu content in welding bead (WB) on the microstructure and mechanical properties of the joint. At preliminary tests, optimal welding parameters were determined to guarantee proper heat input. Welding experiments were performed with the dimensions of the tooth as variables, which is a special technique to tailor Al/Cu content in WB. Macro and microstructure of the cross section of the joints were characterized via optical microscopy (OM) and Scanning Electron Microscopy (SEM) equipped with energy dispersive spectroscopy (EDS). Special band structure(BS) showing lamellar-like flow characteristic is worthy of noticing. Additionally, dispersive Cu particles (DP), forming composite-like structure, were captured. High Cu concentration, however, yielded a harsh material flow due to its high plasticized temperature and poor flowability and can not produce reliable metallurgical bonding. Microhardness of the joint was investigated and the high hardness was caused mainly by the hard intermetallic compounds (IMCs). Besides, tensile tests were conducted to evaluate the joint performance. Based on the result analysis, this joint form has special advantage in tailoring Al/Cu content in WB and controlling the microstructure that imposes significant influence on mechanical properties of the joints.

Dissimilar friction stir welding of 6061 Al to T2 pure Cu adopting tooth-shaped joint configuration: Microstructure and mechanical properties

International Nuclear Information System (INIS)

Zhang, Wei; Shen, Yifu; Yan, Yinfei; Guo, Rui

2017-01-01

In this paper, dissimilar 6061aluminum alloy and commercial pure copper were friction stir butt welded adopting tooth-shaped joint configuration to investigate the influence of Al/Cu content in welding bead (WB) on the microstructure and mechanical properties of the joint. At preliminary tests, optimal welding parameters were determined to guarantee proper heat input. Welding experiments were performed with the dimensions of the tooth as variables, which is a special technique to tailor Al/Cu content in WB. Macro and microstructure of the cross section of the joints were characterized via optical microscopy (OM) and Scanning Electron Microscopy (SEM) equipped with energy dispersive spectroscopy (EDS). Special band structure(BS) showing lamellar-like flow characteristic is worthy of noticing. Additionally, dispersive Cu particles (DP), forming composite-like structure, were captured. High Cu concentration, however, yielded a harsh material flow due to its high plasticized temperature and poor flowability and can not produce reliable metallurgical bonding. Microhardness of the joint was investigated and the high hardness was caused mainly by the hard intermetallic compounds (IMCs). Besides, tensile tests were conducted to evaluate the joint performance. Based on the result analysis, this joint form has special advantage in tailoring Al/Cu content in WB and controlling the microstructure that imposes significant influence on mechanical properties of the joints.

Microstructure of Multi-Pass Friction-Stir-Processed Al-Zn-Mg-Cu Alloys Reinforced by Nano-Sized TiB2 Particles and the Effect of T6 Heat Treatment

Directory of Open Access Journals (Sweden)

Xiaofei Ju

2017-11-01

Full Text Available In this work, a fine-grained structure with a uniform distribution of TiB2 particles and precipitates was achieved in TiB2 particle-reinforced (PR Al-Zn-Mg-Cu alloys by friction stir processing (FSP. The effects of multi-pass FSP on the microstructure, and TiB2 particle distribution, as well as the microstructural evolution in the following T6 treatment, were investigated by X-ray diffraction, scanning electron microscopy and associated electron backscattered diffraction. The results showed that the distribution of TiB2 particles and alloy precipitates was further improved with an increase in the FSP passes. Moreover, compared with alloy segregation in the as-cast PR alloys during T6 treatment, a complete solution of the precipitates was achieved in the FSP-treated PR alloys. The fine-grained structure of the FSP-treated PR alloys was thermally stable without any abnormal growth at the high temperature of T6 treatment due to the pinning effect of dispersed TiB2 particles. The strength and ductility of the PR alloys were simultaneously improved by the combination of FSP and T6 treatment.

Experimental and numerical characterization of anisotropic damage evolution of forged Al6061-T6 alloy

International Nuclear Information System (INIS)

Shen, Y.; Garnier, J.; Allais, L.; Crepin, J.; Ancelet, O.; Hiver, J.M.

2011-01-01

Aluminum alloy 6061-T6 (Al-Mg-Si) has been selected as the material of the vessel for the construction of Jules-Horowitz material testing reactor. Fracture mechanism of this alloy has been investigated using mechanical testing of smooth and notched tensile specimens loaded in different directions. A strong anisotropic fracture behavior has been observed. Microstructural studies using tomography and image analysis have shown a presence of anisotropic distributed coarse precipitates which is the key microstructural feature affecting the damage evolution. These observations were complemented by investigations on fractured tensile samples. A damage scenario of anisotropic growth and coalescence of voids is proposed to explain the fracture behavior associated with the distribution of precipitates. A GTN (Gurson-Tvergaard-Needleman) damage model is used to simulate this scenario and to predict damage evolution. (authors)

Preparation and characterization of silane-modified SiO2 particles reinforced resin composites with fluorinated acrylate polymer.

Science.gov (United States)

Liu, Xue; Wang, Zengyao; Zhao, Chengji; Bu, Wenhuan; Na, Hui

2018-04-01

A series of fluorinated dental resin composites were prepared with two kinds of SiO 2 particles. Bis-GMA (bisphenol A-glycerolate dimethacrylate)/4-TF-PQEA (fluorinated acrylate monomer)/TEGDMA (triethylene glycol dimethacrylate) (40/30/30, wt/wt/wt) was introduced as resin matrix. SiO 2 nanopartices (30nm) and SiO 2 microparticles (0.3µm) were silanized with 3-methacryloxypropyl trimethoxysilane (γ-MPS) and used as fillers. After mixing the resin matrix with 0%, 10%, 20%, 30% SiO 2 nanopartices and 0%, 10%, 20%, 30%, 40%, 50% SiO 2 microparticles, respectively, the fluorinated resin composites were obtained. Properties including double bond conversion (DC), polymerization shrinkage (PS), water sorption (W p ), water solubility (W y ), mechanical properties and cytotoxicity were investigated in comparison with those of neat resin system. The results showed that, filler particles could improve the overall performance of resin composites, particularly in improving mechanical properties and reducing PS of composites along with the addition of filler loading. Compared to resin composites containing SiO 2 microparticles, SiO 2 nanoparticles resin composites had higher DC, higher mechanical properties, lower PS and lower W p under the same filler content. Especially, 50% SiO 2 microparticles reinforced resins exhibited the best flexural strength (104.04 ± 7.40MPa), flexural modulus (5.62 ± 0.16GPa), vickers microhardness (37.34 ± 1.13 HV), compressive strength (301.54 ± 5.66MPa) and the lowest polymerization (3.42 ± 0.22%). Copyright © 2018 Elsevier Ltd. All rights reserved.

The memorable service and monastic humility – the history of Stanisław Konarski’s heart

Directory of Open Access Journals (Sweden)

Ryszard Mączyński

2016-12-01

Full Text Available The article concentrates on an interesting 130-year-old artefact located in the Krakow church of Piarists – the decoration of the place where Stanisław Konarski’s (1700–1773 heart was buried. Konarski was a monk of the Pious Schools in the 18th century, as well as publisher of a collection of national laws Volumina legum, a bold commentator calling for strengthening royal power and abolishing liberum veto, reformer of the educational system and founder of the renowned, modern Collegium Nobilium. The circumstances of the discovery and relocation of the relic in 1882 from Warsaw to Krakow and the ceremony of its introduction to the monastic Church of the Transfiguration of Jesus on February 13 are also outlined. Three significant research issues are also discussed. The first one is the problem of the authenticity of the artefact, which was discovered more than a hundred years after Konarski’s death in the possession of a Warsaw optician Jakub Pik. It was then that the question started occupying the minds of researchers, including the rector of the Krakow college Adam Słotwiński. The question is made more relevant by the lack of any direct evidence from 1773 about the removal of Stanisław Konarski’s heart from his body after his death. The information gathered so far allow us to assume, with probability bordering on certainty, that it is authentic and the only surviving part of this famous monk’s body. Another question, totally absent from past reflections on the subject, is the reason why the heart was removed. This particular aspect turns our attention at a strikingly popular early-modern Polish tradition – first in royal families, later also among magnates and nobility – of burying hearts separately, usually by entombing them in a church founded by the deceased. It was found that a considerable number of hearts removed from bodies had been inhumed in Piarist churches (Rzeszów, Warsaw or Łowicz. This tradition, however, did

Experimental Study on Unconfined Compressive Strength of Organic Polymer Reinforced Sand

Directory of Open Access Journals (Sweden)

Jin Liu

2018-01-01

Full Text Available The natural sand is loose in structure with a small cohesive force. Organic polymer can be used to reinforce this sand. To assess the effectiveness of organic polymer as soil stabilizer (PSS, a series of unconfined compressive strength tests have been performed on reinforced sand. The focus of this study was to determine a curing method and a mix design to stabilize sand. The curing time, PSS concentration, and sand density were considered as variables in this study. The reinforcement mechanism was analyzed with images of scanning electron microscope (SEM. The results indicated that the strength of stabilized sand increased with the increase in the curing time, concentration, and sand density. The strength plateaus are at about curing time of 48 h. The UCS of samples with density of 1.4 g/cm3 at 10%, 20%, 30%, 40%, and 50% PSS concentration are 62.34 kPa, 120.83 kPa, 169.22 kPa, 201.94 kPa, and 245.28 kPa, respectively. The UCS of samples with PSS concentration of 30% at 1.4 g/cm3, 1.5 g/cm3, and 1.6 g/cm3 density are 169.22 kPa, 238.6 kPa 5, and 281.69 kPa, respectively. The chemical reaction between PSS and sand particle is at its microlevel, which improves the sand strength by bonding its particles together and filling the pore spaces. In comparison with the traditional reinforcement methods, PSS has the advantages of time saving, lower cost, and better environment protection. The research results can be useful for practical engineering applications, especially for reinforcement of foundation, embankment, and landfill.

Gas tungsten arc welding assisted hybrid friction stir welding of dissimilar materials Al6061-T6 aluminum alloy and STS304 stainless steel

International Nuclear Information System (INIS)

Bang, HanSur; Bang, HeeSeon; Jeon, GeunHong; Oh, IkHyun; Ro, ChanSeung

2012-01-01

Highlights: ► GTAW assisted hybrid friction stir welding (HFSW) has been carried out for dissimilar butt joint. ► Mechanical strength of dissimilar butt joint by HFSW and FSW has been investigated and compared. ► Microstructure of dissimilar butt joint by HFSW and FSW has been investigated and compared. -- Abstract: The aim of this research is to evaluate the potential for using the gas tungsten arc welding (GTAW) assisted hybrid friction stir welding (HFSW) process to join a stainless steel alloy (STS304) to an aluminum alloy (Al6061) in order to improve the weld strength. The difference in mechanical and microstructural characteristics of dissimilar joint by friction stir welding (FSW) and HFSW has been investigated and compared. Transverse tensile strength of approximately 93% of the aluminum alloy (Al6061) base metal tensile strength is obtained with HFSW, which is higher than the tensile strength of FSW welds. This may be due to the enhanced material plastic flow and partial annealing effect in dissimilar materials due to preheating of stainless steel surface by GTAW, resulting in significantly increased elongation of welds. The results indicate that HFSW that integrates GTAW preheating to FSW is advantageous in joining dissimilar combinations compared to conventional FSW.

High-speed interaction of natural and technogenic particles with the brittle and plastic elements of spacecrafts

Science.gov (United States)

Gerasimov, A. V.; Pashkov, S. V.; Khristenko, Yu. F.

2017-10-01

The paper represents the results of a study concerning the high-speed interaction of natural and technogenic particles with aluminum, glass and glass-reinforced laminate targets of finite thickness. These materials are widely used as the structural elements of spacecrafts such as spacecraft bodies, tanks, windows, glass in optical devices, heat shields, etc. This paper considers the impact, deformation and fracture of aluminum, glass and asbestos-reinforced laminate samples with aluminum and steel particles which represent space debris and with ice and granite particles which represent the natural particles of space bodies

Evaluation of Interface Shear Strength Properties of Geogrid Reinforced Foamed Recycled Glass Using a Large-Scale Direct Shear Testing Apparatus

Directory of Open Access Journals (Sweden)

Arul Arulrajah

2015-01-01

Full Text Available The interface shear strength properties of geogrid reinforced recycled foamed glass (FG were determined using a large-scale direct shear test (DST apparatus. Triaxial geogrid was used as a geogrid reinforcement. The geogrid increases the confinement of FG particles during shear; consequently the geogrid reinforced FG exhibits smaller vertical displacement and dilatancy ratio than FG at the same normal stress. The failure envelope of geogrid reinforced FG, at peak and critical states, coincides and yields a unique linear line possibly attributed to the crushing of FG particles and the rearrangement of crushed FG after peak shear state. The interface shear strength coefficient α is approximately constant at 0.9. This value can be used as the interface parameter for designing a reinforced embankment and mechanically stabilized earth (MSE wall when FG is used as a lightweight backfill and triaxial geogrid is used as an extensible earth reinforcement. This research will enable FG, recently assessed as suitable for lightweight backfills, to be used together with geogrids in a sustainable manner as a lightweight MSE wall. The geogrid carries tensile forces, while FG reduces bearing stresses imposed on the in situ soil. The use of geogrid reinforced FG is thus significant from engineering, economical, and environmental perspectives.

Evaluation on microscopic damage and fabrication process of shape memory alloy

International Nuclear Information System (INIS)

Lee, Jin Kyung; Choi, Il Kook; Park, Young Chul; Lee, Kyu Chang; Lee, Jun Hyun

2002-01-01

Shape memory alloy has been used to improve the tensile strength of composite by the occurrence of compressive residual stress in matrix using its shape memory effect. In order to fabricate shape memory alloy composite, TiNi alloy and Al6061 were used as reinforcing material and matrix, respectively. In this study, TiNi/Al6061 shape memory alloy composite was made by using hot press method. However, the specimen fabricated by this method had the bonding problem at tile boundary between TiNi fiber anti Al matrix when the load was applied to it. A cold rolling was imposed to the specimen to improve the bonding effort. It was found that tensile strength of specimen subjected to cold rolling was more increased than that of specimen which did not underwent cold rolling. In addition, acoustic emission technique was used to quantify the microscopic damage behavior of cold rolled TiNi/Al6061 shape memory alloy composite at high temperature.

Mechanical Properties Of AA 6061-T6 Aluminum Alloy Friction Stir Welds

Directory of Open Access Journals (Sweden)

Asmaa M. Abdullah

2015-06-01

Full Text Available The different parameters on mechanical and microstructural properties of aluminium alloy 6061-T6 Friction stir-welded (FSW joints were investigated in the present study. Different welded specimens were produced by employing variable rotating speeds and welding speeds. Tensile strength of the produced joints was tested at room temperature and the the effecincy was assessed, it was 75% of the base metal at rotational speed 1500 rpm and weld speed 50 mm/min. Hardness of various zones of FSW welds are presented and analyzed by means of brinell hardness number . Besides to thess tests the bending properties investigated and showed good results in some specimen and not in onother the mamximum stress was 240 N/mm2 at rotational speed 1500 rpm and weld speed 50 mm/min , while the maximum stress at 1250 rpm and 75 mm/min 94 N/mm2 , hardness results shwed lower values in heat affected and nugget zones than the base metal with improving of hardness at 1500 rpm, 75 mm/min .

Investigations on mechanical and two-body abrasive wear behaviour of glass/carbon fabric reinforced vinyl ester composites

International Nuclear Information System (INIS)

Suresha, B.; Kumar, Kunigal N. Shiva

2009-01-01

The aim of the research article is to study the mechanical and two-body abrasive wear behaviour of glass/carbon fabric reinforced vinyl ester composites. The measured wear volume loss increases with increase in abrading distance/abrasive particle size. However, the specific wear rate decreases with increase in abrading distance and decrease in abrasive particle size. The results showed that the highest specific wear rate is for glass fabric reinforced vinyl ester composite with a value of 10.89 x 10 -11 m 3 /Nm and the lowest wear rate is for carbon fabric reinforced vinyl ester composite with a value of 4.02 x 10 -11 m 3 /Nm. Mechanical properties were evaluated and obtained values are compared with the wear behaviour. The worn surface features have been examined using scanning electron microscope (SEM). Photomicrographs of the worn surfaces revealed higher percentage of broken glass fiber as compared to carbon fiber. Also better interfacial adhesion between carbon and vinyl ester in carbon reinforced vinyl ester composite was observed.

Stanisław Przybyszewski — mizogin czy poszukiwacz miłości idealnej?

OpenAIRE

Murzicz, Ewelina

2011-01-01

This article presents and analyses the motif of women in Stanisław Przybyszewski’s novels. The author focused on the woman’s nature and presented the way it influenced the man’s character and life. Przybyszewski’s work is an attempt at answering questions about the point of love and desire; it also includes problems connected with metaphysical side of love and impossibility to achieve any unity between the man and the woman. Publikacja dofinansowana przez Wydział Filologiczny U...

Reinforcement with alumina particles at the interface region of AA6101-T6 and AA1350 alloys during friction stir welding

Science.gov (United States)

Ashok Kumar, R.; Thansekhar, M. R.

2018-04-01

This paper deals the combinational effect of friction stir welding and friction stir processing on dissimilar AA6101-T6 and AA1350 aluminium alloys. For that, alumina particles are reinforced at interface region of AA6101-T6 and AA1350 aluminium alloys. Friction Stir Welding and Friction Stir Processing are done simultaneously for various sizes of groove. To analyze the welding quality and surface modifications, mechanical, wear and microstructural tests are carried out. Among these, smallest groove of 0.5 mm width and 1 mm depth reveals highest tensile and bending strengths and largest groove of 2 mm width and 3 mm depth gives maximum hardness and wear resistance. Taguchi technique shows that groove width is most influencing parameter. Developed second order models with interaction predict the responses with minimum error.

Optimization Design and Application of Underground Reinforced Concrete Bifurcation Pipe

Directory of Open Access Journals (Sweden)

Chao Su

2015-01-01

Full Text Available Underground reinforced concrete bifurcation pipe is an important part of conveyance structure. During construction, the workload of excavation and concrete pouring can be significantly decreased according to optimized pipe structure, and the engineering quality can be improved. This paper presents an optimization mathematical model of underground reinforced concrete bifurcation pipe structure according to real working status of several common pipe structures from real cases. Then, an optimization design system was developed based on Particle Swarm Optimization algorithm. Furthermore, take the bifurcation pipe of one hydropower station as an example: optimization analysis was conducted, and accuracy and stability of the optimization design system were verified successfully.

Stable particles

International Nuclear Information System (INIS)

Samios, N.P.

1993-01-01

I have been asked to review the subject of stable particles, essentially the particles that eventually comprised the meson and baryon octets. with a few more additions -- with an emphasis on the contributions made by experiments utilizing the bubble chamber technique. In this activity, much work had been done by the photographic emulsion technique and cloud chambers-exposed to cosmic rays as well as accelerator based beams. In fact, many if not most of the stable particles were found by these latter two techniques, however, the forte of the bubble chamber (coupled with the newer and more powerful accelerators) was to verify, and reinforce with large statistics, the existence of these states, to find some of the more difficult ones, mainly neutrals and further to elucidate their properties, i.e., spin, parity, lifetimes, decay parameters, etc

Reinforcement Magnitude: An Evaluation of Preference and Reinforcer Efficacy

OpenAIRE

Trosclair-Lasserre, Nicole M; Lerman, Dorothea C; Call, Nathan A; Addison, Laura R; Kodak, Tiffany

2008-01-01

Consideration of reinforcer magnitude may be important for maximizing the efficacy of treatment for problem behavior. Nonetheless, relatively little is known about children's preferences for different magnitudes of social reinforcement or the extent to which preference is related to differences in reinforcer efficacy. The purpose of the current study was to evaluate the relations among reinforcer magnitude, preference, and efficacy by drawing on the procedures and results of basic experimenta...

Preparation of Ti-aluminide reinforced in situ aluminium matrix composites by reactive hot pressing

International Nuclear Information System (INIS)

Roy, D.; Ghosh, S.; Basumallick, A.; Basu, B.

2007-01-01

Aluminium based metal matrix composites reinforced with in situ Ti-aluminide and alumina particles were prepared by reactive hot pressing a powder mix of aluminium and nanosized TiO 2 powders. The reinforcements were formed in situ by exothermal reaction between the TiO 2 nano crystalline powder and aluminium. The thermal characteristics of the in situ reaction were studied with the aid of Differential scanning calorimetry (DSC). X-ray diffraction (XRD), Energy dispersive spectroscopy (EDS) and Scanning electron microscopy (SEM) techniques were employed to study the microstructural architecture of the composites as a function of hot pressing temperature and volume percent reinforcement. Microhardness measurements on the as prepared in situ aluminium matrix composites exhibit significant increase in hardness with increase in hot pressing temperature and volume fraction of reinforcement

Experimental data of the static behavior of reinforced concrete beams at room and low temperature.

Science.gov (United States)

Mirzazadeh, M Mehdi; Noël, Martin; Green, Mark F

2016-06-01

This article provides data on the static behavior of reinforced concrete at room and low temperature including, strength, ductility, and crack widths of the reinforced concrete. The experimental data on the application of digital image correlation (DIC) or particle image velocimetry (PIV) in measuring crack widths and the accuracy and precision of DIC/PIV method with temperature variations when is used for measuring strains is provided as well.

High-Strain-Rate Material Behavior and Adiabatic Material Instability in Impact of Micron-Scale Al-6061 Particles

Science.gov (United States)

Chen, Qiyong; Alizadeh, Arash; Xie, Wanting; Wang, Xuemei; Champagne, Victor; Gouldstone, Andrew; Lee, Jae-Hwang; Müftü, Sinan

2018-04-01

Impact of spherical particles onto a flat sapphire surface was investigated in 50-950 m/s impact speed range experimentally and theoretically. Material parameters of the bilinear Johnson-Cook model were determined based on comparison of deformed particle shapes from experiment and simulation. Effects of high-strain-rate plastic flow, heat generation due to plasticity, material damage, interfacial friction and heat transfer were modeled. Four distinct regions were identified inside the particle by analyzing temporal variation of material flow. A relatively small volume of material near the impact zone becomes unstable due to plasticity-induced heating, accompanied by severe drop in the flow stress for impact velocity that exceeds 500 m/s. Outside of this region, flow stress is reduced due to temperature effects without the instability. Load carrying capacity of the material degrades and the material expands horizontally leading to jetting. The increase in overall plastic and frictional dissipation with impact velocity was found to be inherently lower than the increase in the kinetic energy at high speeds, leading to the instability. This work introduces a novel method to characterize HSR (109 s-1) material properties and also explains coupling between HSR material behavior and mechanics that lead to extreme deformation.

Effect of Home Bleaching on Microleakage of Fiber-reinforced and Particle-filled Composite Resins

Directory of Open Access Journals (Sweden)

Farahnaz Sharafeddin

2013-12-01

Full Text Available Background and aims. Bleaching may exert some negative effects on existing composite resin restorations. The aim of this study was to evaluate the effect of home bleaching on microleakage of fiber-reinforced and particle-filled composite resins. Materials and methods. Ninety class V cavities (1.5×2×3 mm were prepared on the buccal surfaces of 90 bovine teeth. The teeth were randomly divided into 6 groups (n=15 and restored as follows: Groups 1 and 2 with Z100, groups 3 and 4 with Z250, and groups 5 and 6 with Nulite F composite resins. All the specimens were thermocycled. Groups 1, 3 and 5 were selected as control groups (without bleaching and the experimental groups 2, 4 and 6 were bleached with 22% carbamide peroxide gel. All the samples were immersed in 2% basic fuchsin dye for 24 hours and then sectioned longitudinally. Dye penetration was evaluated under a stereomicroscope (×25, at both the gingival and incisal margins. Data were analyzed using Kruskal-Wallis, Mann-Whitney and Wilcoxon tests (α=0.05. Results. Statistical analyses revealed that bleaching gel increased microleakage only at gingival margins with Z250 (P=0.007. Moreover, the control groups showed a statistically significant difference in microleakage at their gingival margins. Nulite F had the maximum microleakage while Z250 showed the minimum (P=0.006. Conclusion. Microleakage of home-bleached restorations might be related to the type of composite resin used.

Characterization and Correlation of Particle-Level Interactions to the Macroscopic Rheology of Powders, Granular Slurries, and Colloidal Suspensions

Energy Technology Data Exchange (ETDEWEB)

A.P. Poloski; R.C. Daniel; D.R. Rector; P.R. Bredt; E.C. Buck; Berg, J.C.; Saez, A.E.

2006-09-29

This project had two primary objectives. The first was to understand the physical properties and behavior of select Hanford tank sludges under conditions that might exist during retrieval, treatment, packaging, and transportation for disposal at the Waste Isolation Pilot Plant (WIPP). The second objective was to develop a fundamental understanding of these sludge suspensions by correlating the macroscopic properties with particle interactions occurring at the colloidal scale. The specific tank wastes considered herein are contained in thirteen Hanford tanks including three double-shell tanks (DSTs) (AW-103, AW-105, and SY-102) and ten single-shell tanks (SSTs) (B-201 through B-204, T-201 through T-204, T-110, and T-111). At the outset of the project, these tanks were designated as potentially containing transuranic (TRU) process wastes that would be treated and disposed of in a manner different from the majority of the tank wastes.

Discontinuously reinforced titanium matrix composites for fusion applications

International Nuclear Information System (INIS)

Castro, V.; Leguey, T.; Monge, M.A.; Munoz, A.; Pareja, R.; Victoria, M.

2002-01-01

We have reinforced α-Ti with different contents of TiC particles using the in situ technique and conventional casting. Compositional and microstructural characterization of the TiC/Ti composite material was made by XRD and SEM-EDS. Tensile tests at RT, 723 and 973 K have been performed on samples heat treated at 1000 K for 30 min which were prepared from cold rolled material. The effect of the content, size and morphology of the TiC particles on the tensile properties has been investigated. The results indicate that the expected improvement in the mechanical characteristics of TiC/Ti composites is inhibited by the detrimental presence of coarse dendritic particles of TiC. The premature failure of these composites at RT is due to cracking of the coarse TiC particles. Local softening due to inhomogeneous plastic deformation of the Ti matrix appears to contribute to the tensile failure of the TiC/Ti composites deformed at 723 and 973 K.

Discontinuously reinforced titanium matrix composites for fusion applications

Energy Technology Data Exchange (ETDEWEB)

Castro, V. E-mail: mvcastro@fis.uc3m.es; Leguey, T.; Monge, M.A.; Munoz, A.; Pareja, R.; Victoria, M

2002-12-01

We have reinforced {alpha}-Ti with different contents of TiC particles using the in situ technique and conventional casting. Compositional and microstructural characterization of the TiC/Ti composite material was made by XRD and SEM-EDS. Tensile tests at RT, 723 and 973 K have been performed on samples heat treated at 1000 K for 30 min which were prepared from cold rolled material. The effect of the content, size and morphology of the TiC particles on the tensile properties has been investigated. The results indicate that the expected improvement in the mechanical characteristics of TiC/Ti composites is inhibited by the detrimental presence of coarse dendritic particles of TiC. The premature failure of these composites at RT is due to cracking of the coarse TiC particles. Local softening due to inhomogeneous plastic deformation of the Ti matrix appears to contribute to the tensile failure of the TiC/Ti composites deformed at 723 and 973 K.

Tensile and Compressive Responses of Ceramic and Metallic Nanoparticle Reinforced Mg Composites

Directory of Open Access Journals (Sweden)

Quy Bau Nguyen

2013-05-01

Full Text Available In the present study, room temperature mechanical properties of pure magnesium, Mg/ZrO2 and Mg/(ZrO2 + Cu composites with various compositions are investigated. Results revealed that the use of hybrid (ZrO2 + Cu reinforcements in Mg led to enhanced mechanical properties when compared to that of single reinforcement (ZrO2. Marginal reduction in mechanical properties of Mg/ZrO2 composites were observed mainly due to clustering of ZrO2 particles in Mg matrix and lack of matrix grain refinement. Addition of hybrid reinforcements led to grain size reduction and uniform distribution of hybrid reinforcements, globally and locally, in the hybrid composites. Macro- and micro- hardness, tensile strengths and compressive strengths were all significantly increased in the hybrid composites. With respect to unreinforced magnesium, failure strain was almost unchanged under tensile loading while it was reduced under compressive loading for both Mg/ZrO2 and Mg/(ZrO2 + Cu composites.

Conjugative plasmid pAW63 brings new insights into the genesis of the Bacillus anthracis virulence plasmid pXO2 and of the Bacillus thuringiensis plasmid pBT9727

Directory of Open Access Journals (Sweden)

Mahillon Jacques

2005-07-01

Full Text Available Abstract Background Bacillus cereus, Bacillus anthracis and Bacillus thuringiensis belong to the genetically close-knit Bacillus cereus sensu lato group, a family of rod-shaped Gram-positive bacteria. pAW63 is the first conjugative plasmid from the B. cereus group to be completely sequenced. Results The 71,777 bp nucleotide sequence of pAW63 reveals a modular structure, including a 42 kb tra region encoding homologs of the Type IV secretion systems components VirB11, VirB4 and VirD4, as well as homologs of Gram-positive conjugation genes from Enterococcus, Lactococcus, Listeria, Streptococcus and Staphylococcus species. It also firmly establishes the existence of a common backbone between pAW63, pXO2 from Bacillus anthracis and pBT9727 from the pathogenic Bacillus thuringiensis serovar konkukian strain 97-27. The alignment of these three plasmids highlights the presence of well conserved segments, in contrast to distinct regions of high sequence plasticity. The study of their specific differences has provided a three-point reference framework that can be exploited to formulate solid hypotheses concerning the functionalities and the molecular evolution of these three closely related plasmids. This has provided insight into the chronology of their divergence, and led to the discovery of two Type II introns on pAW63, matching copies of the mobile element IS231L in different loci of pXO2 and pBT9727, and the identification on pXO2 of a 37 kb pathogenicity island (PAI containing the anthrax capsule genes. Conclusion The complete sequence determination of pAW63 has led to a functional map of the plasmid yielding insights into its conjugative apparatus, which includes T4SS-like components, as well as its resemblance to other large plasmids of Gram-positive bacteria. Of particular interest is the extensive homology shared between pAW63 and pXO2, the second virulence plasmid of B. anthracis, as well as pBT9727 from the pathogenic strain B. thuringiensis

Reinforced sulphur concrete

NARCIS (Netherlands)