WorldWideScience

Sample records for automotive shredder residues

  1. Automotive shredder residue (ASR) characterization for a valuable management.

    Science.gov (United States)

    Morselli, Luciano; Santini, Alessandro; Passarini, Fabrizio; Vassura, Ivano

    2010-11-01

    Car fluff is the waste produced after end-of-life-vehicles (ELVs) shredding and metal recovery. It is made of plastics, rubber, glass, textiles and residual metals and it accounts for almost one-third of a vehicle mass. Due to the approaching of Directive 2000/53/EC recycling targets, 85% recycling rate and 95% recovery rate in 2015, the implementation of automotive shredder residue (ASR) sorting and recycling technologies appears strategic. The present work deals with the characterization of the shredder residue coming from an industrial plant, representative of the Italian situation, as for annual fluxes and technologies involved. The aim of this study is to characterize ASR in order to study and develop a cost effective and environmentally sustainable recycling system. Results show that almost half of the residue is made of fines and the remaining part is mainly composed of polymers. Fine fraction is the most contaminated by mineral oils and heavy metals. This fraction produces also up to 40% ashes and its LHV is lower than the plastic-rich one. Foam rubber represents around half of the polymers share in car fluff. Moreover, some chemical-physical parameters exceed the limits of some parameters fixed by law to be considered refuse derived fuel (RDF). As a consequence, ASR needs to be pre-treated in order to follow the energy recovery route.

  2. Challenges around automotive shredder residue production and disposal.

    Science.gov (United States)

    Khodier, Ala; Williams, Karl; Dallison, Neil

    2017-05-10

    The challenge for the automotive industry is how to ensure they adopt the circular economy when it comes to the disposal of end-of-life vehicles (ELV). According to the European Commission the UK achieved a total reuse and recovery rate of 88%. This is short of the revised ELV directive target of 95% materials recovery, which requires a minimum of 85% of materials to be recycled or reused. A significant component of the recycling process is the production of automotive shredder residue (ASR). This is currently landfilled across Europe. The additional 10% could be met by processing ASR through either waste-to-energy facilities or Post shredder technology (PST) to recover materials. The UK auto and recycling sectors claimed there would need to be a massive investment by their members in both new capacity and new technology for PST to recover additional recycle materials. It has been shown that 50% of the ASR contains valuable recoverable materials which could be used to meet the Directive target. It is expected in the next 5years that technological innovation in car design will change the composition from easily recoverable metal to difficult polymers. This change in composition will impact on the current drive to integrate the European Circular Economy Package. A positive factor is that main driver for using ASR is coming from the metals recycling industry itself. They are looking to develop the infrastructure for energy generation from ASR and subsequent material recovery. This is driven by the economics of the process rather than meeting the Directive targets. The study undertaken has identified potential pathways and barriers for commercial thermal treatment of ASR. The results of ASR characterisation were used to assess commercial plants from around the world. Whilst there were many claiming that processing of ASR was possible none have so far shown both the technological capability and economic justification. Copyright © 2017 Elsevier Ltd. All rights reserved.

  3. All auto shredding: evaluation of automotive shredder residue generated by shredding only vehicles.

    Energy Technology Data Exchange (ETDEWEB)

    Duranceau, C. M.; Spangenberger, J. S. (Energy Systems); (Vehicle Recycling Partnership, LLC); (American Chemistry Counsel, Plastics Division)

    2011-09-26

    A well developed infrastructure exists for the reuse and recycling of automotive parts and materials. At the end of a vehicle's useful life many parts are removed and sold for reuse and fluids are recovered for recycling or proper disposal. What remains is shredded, along with other metal bearing scrap such as home appliances, demolition debris and process equipment, and the metals are separated out and recycled. The remainder of the vehicle materials is call shredder residue which ends up in the landfill. As energy and natural resources becomes more treasured, increased effort has been afforded to find ways to reduce energy consumption and minimize the use of our limited resources. Many of the materials found in shredder residue could be recovered and help offset the use of energy and material consumption. For example, the energy content of the plastics and rubbers currently landfilled with the shredder residue is equivalent to 16 million barrels of oil per year. However, in the United States, the recovered materials, primarily polymers, cannot be recycled due to current regulatory barriers which preclude the re-introduction into commerce of certain materials because of residual contamination with substances of concern (SOCs) such as polychlorinated biphenyls (PCBs). The source of the PCBs is not well understood. Old transformers, capacitors, white goods and ballasts from lighting fixtures are likely contributing factors. The project was designed to evaluate whether vehicles of varying age and manufacturing origin contribute to the PCB content in shredder residue. Additionally, the project was designed to determine if there are any trends in material composition of the shredder residue from varied age and manufacturing groups. This information would aid in future material recovery facility strategy and design. The test utilized a newly installed shredder plant to shred four categories of automobiles. The categories were defined by vehicle age and the

  4. Characterization of automotive shredder residues before and five years after landfill disposal

    Directory of Open Access Journals (Sweden)

    Lucian Ionel Cioca

    2015-04-01

    Full Text Available The paper illustrates the results of an extensive analytical characterization study of automotive shredder residues (ASR, also known as "fluff”. The analyses concerned material fractions and their content, with special reference to heavy metals (e.g. Cd, Cr, Hg, Pb, Cu and arsenic. Elution tests on the original materials were also conducted. Moreover, chemical concentrations of ASR samples after about five years' landfill residence was assessed, in order to verify possible changes resulting from both in-situ leaching and organic matter degradation phenomena. Results show that lead seems to be the most critical element in view of possible ASR acceptance in non-hazardous waste landfills because of its high concentration in raw waste and, especially, of its proven leachability characteristics.

  5. Extraction of metals from automotive shredder residue:Preliminary results of different leaching systems

    Institute of Scientific and Technical Information of China (English)

    Francesco Ferella; Ida De Michelis; Agostino Scocchera; Mario Pelino; Francesco Vegliò

    2015-01-01

    The study is focused on the extraction of valuable metals from automotive shredder residue (ASR) by different leaching solutions. First, ASR samples were roasted at 600 °C to simulate a thermal treatment processing. Distil ed water, citric and sulphuric acid were preliminarily investigated, thus two further full factorial systems entailing H2SO4–H2O2 and H2SO4–H2O2–Fe3+ were tested. The preliminary experimental results showed that 0.1 mol·L−1 H2SO4 solution extracted 100%of Cu, Fe and Zn, whereas citric acid leached 100%of Zn and Pb, 59%of Fe and 62%of Cu;whereas, H2SO4–H2O2 and H2SO4–H2O2–Fe3+(Fenton's) leaching media showed that Cu, Fe and Zn can be extracted simultaneously and completely from the ASR ashes before final disposal.

  6. Life cycle assessment of innovative technology for energy production from automotive shredder residue.

    Science.gov (United States)

    Rinaldi, Caterina; Masoni, Paolo; Salvati, Fabio; Tolve, Pietro

    2015-07-01

    Automotive Shredder Residue (ASR) is a problematic waste material remaining after shredding and recovery processes of end-of-life vehicles (ELVs). Its heterogeneous grain size and composition make difficult its recovery or disposal. Although ASR accounts for approximately 20% to 25% of the weight of an ELV, the European Union (EU)'s ELV Directive (2000/53/EC) requires that by 2015 a minimum 95% of the weight of an ELV must be reused or recovered, including a 10% weight energy recovery. The quantity of ASR is relevant: Approximately 2.4 million tons are generated in the EU each year and most of it is sent to landfills. This article describes a life cycle model of the "TEKNE-Fluff" process designed to make beneficial use of ASR that is based on the results of an experimental pilot plant for pyro-gasification, combustion, cogeneration, and emissions treatment of ASR. The goal of the research was the application of life cycle assessment (LCA) methodology to identify the environmental hot spots of the "TEKNE system" and use scenario analysis to check solutions to improve its environmental profile, supporting the design and industrialization process. The LCA was conducted based on data modeled from the experimental campaign. Moreover, different scenarios on shares of electricity and thermal energy produced by the cogeneration system and alternative treatment processes for the waste produced by the technology were compared. Despite the limitation of the research (results based on scaling up experimental data by modeling), impact assessment results are promising and sufficiently robust, as shown by Monte Carlo analysis. The TEKNE technology may become an interesting solution for the problem of ASR management: Besides representing an alternative to landfill disposal, the energy produced could avoid significant impacts on fossil resources depletion (a plant of 40,000 tons/y capacity could produce ∼ 147,000 GJ/yr, covering the annual need of ∼ 13,500 households).

  7. Pyrolysis of automotive shredder residue in a bench scale rotary kiln.

    Science.gov (United States)

    Notarnicola, Michele; Cornacchia, Giacinto; De Gisi, Sabino; Di Canio, Francesco; Freda, Cesare; Garzone, Pietro; Martino, Maria; Valerio, Vito; Villone, Antonio

    2017-07-01

    Automotive shredder residue (ASR) can create difficulties when managing, with its production increasing. It is made of different type of plastics, foams, elastomers, wood, glasses and textiles. For this reason, it is complicated to dispose of in a cost effective way, while also respecting the stringent environmental restrictions. Among thermal treatments, pyrolysis seems to offer an environmentally attractive method for the treatment of ASR; it also allows for the recovery of valuable secondary materials/fuels such as pyrolysis oils, chars, and gas. While, there is a great deal of significant research on ASR pyrolysis, the literature on higher scale pyrolysis experiments is limited. To improve current literature, the aim of the study was to investigate the pyrolysis of ASR in a bench scale rotary kiln. The Italian ASR was separated by dry-sieving into two particle size fractions: d30mm. Both the streams were grounded, pelletized and then pyrolyzed in a continuous bench scale rotary kiln at 450, 550 and 650°C. The mass flow rate of the ASR pellets was 200-350g/h and each test ran for about 4-5h. The produced char, pyrolysis oil and syngas were quantified to determine product distribution. They were thoroughly analyzed with regard to their chemical and physical properties. The results show how higher temperatures increase the pyrolysis gas yield (44wt% at 650°C) as well as its heating value. The low heating value (LHV) of syngas ranges between 18 and 26MJ/Nm(3)dry. The highest pyrolysis oil yield (33wt.%) was observed at 550°C and its LHV ranges between 12.5 and 14.5MJ/kg. Furthermore, only two out of the six produced chars respect the LHV limit set by the Italian environmental regulations for landfilling. The obtained results in terms of product distribution and their chemical-physical analyses provide useful information for plant scale-up. Copyright © 2017 Elsevier Ltd. All rights reserved.

  8. Materials recovery from shredder residues

    Energy Technology Data Exchange (ETDEWEB)

    Daniels, E. J.; Jody, B. J.; Pomykala, J., Jr.

    2000-07-24

    Each year, about five (5) million ton of shredder residues are landfilled in the US. Similar quantities are landfilled in Europe and the Pacific Rim. Landfilling of these residues results in a cost to the existing recycling industry and also represents a loss of material resources that are otherwise recyclable. In this paper, the authors outline the resources recoverable from typical shredder residues and describe technology that they have developed to recover these resources.

  9. Interpretation on Recycling Plastics from Shredder Residue

    Science.gov (United States)

    EPA is considering an interpretation of its regulations that would generally allow for recycling of plastic separated from shredder residue under the conditions described in the Voluntary Procedures for Recycling Plastics from Shredder Residue.

  10. Landfill Mining of Shredder Residues

    DEFF Research Database (Denmark)

    Hansen, Jette Bjerre; Hyks, Jiri; Shabeer Ahmed, Nassera

    In Denmark, shredder residues (SR) are classified as hazardous waste and until January 2012 the all SR were landfilled. It is estimated that more than 1.8 million tons of SR have been landfilled in mono cells. This paper describes investigations conducted at two Danish landfills. SR were excavated...

  11. Mass balance and composition analysis of shredder residue.

    Energy Technology Data Exchange (ETDEWEB)

    Pomykala, J. A., Jr.; Jody, B. J.; Spangenberger, J. S.; Daniels, E. J.; Energy Systems

    2007-01-01

    The process of shredding end-of-life vehicles to recover metals results in a byproduct commonly referred to as shredder residue. The four-and-a-half million metric tons of shredder residue produced annually in the United States is presently land filled. To meet the challenges of automotive materials recycling, the U.S. Department of Energy is supporting research at Argonne National Laboratory in cooperation with the Vehicle Recycling Partnership (VRP) of the United States Council for Automotive Research (USCAR) and the American Plastics Council. This paper presents the results of a study that was conducted by Argonne to determine variations in the composition of shredder residue from different shredders. Over 90 metric tons of shredder residues were processed through the Argonne pilot plant. The contents of the various separated streams were quantitatively analyzed to determine their composition and to identify materials that should be targeted for recovery. The analysis established a reliable mass balance for the different materials in shredder residue.

  12. Utilization of automotive shredder residues in a thermal process for recovery of manganese and zinc from zinc-carbon and alkaline spent batteries.

    Science.gov (United States)

    Ippolito, N M; Belardi, G; Medici, F; Piga, L

    2016-05-01

    The aim of the study is the recovery by thermal treatment of manganese and zinc from a mixture of zinc-carbon and alkaline spent batteries, on the basis of the different phase change temperatures of the two metal-bearing phases. ASR (Automotive Shredder Residue), containing 68% of carbon, was added to the mixture to act as a reductant to metallic Zn of the zinc-bearing phases. The mixture was subsequently heated in different atmospheres (air, CO2 and N2) and at different temperatures (900°C, 1000°C and 1200°C) and stoichiometric excess of ASR (300%, 600% and 900%). Characterization of the mixture and of the residues of thermal treatment was carried out by chemical analysis, TGA/DTA, SEM and XRD. The results show that recovery of 99% of zinc (grade 97%) is achieved at 1000°C in N2 with a stoichiometric excess of car-fluff of 900%. This product could be suitable for production of new batteries after refining by hydrometallurgical way. Recovery of Mn around 98% in the residue of the treatment is achieved at any temperature and atmosphere tested with a grade of 57% at 900% excess of car-fluff. This residue is enriched in manganese oxide and could be used in the production of iron-manganese alloys.

  13. Preliminary investigation on the thermal conversion of automotive shredder residue into value-added products: Graphitic carbon and nano-ceramics.

    Science.gov (United States)

    Mayyas, Mohannad; Pahlevani, Farshid; Handoko, Wilson; Sahajwalla, Veena

    2016-04-01

    Large increasing production volumes of automotive shredder residue (ASR) and its hazardous content have raised concerns worldwide. ASR has a desirable calorific value, making its pyrolysis a possible, environmentally friendly and economically viable solution. The present work focuses on the pyrolysis of ASR at temperatures between 950 and 1550°C. Despite the high temperatures, the energy consumption can be minimized as the decomposition of ASR can be completed within a short time. In this study, the composition of ASR was investigated. ASR was found to contain about 3% Ti and plastics of high calorific value such as polypropylene, polyethylene, polycarbonate and polyurethane. Based on thermogravimetric analysis (TGA) of ASR, the non-isothermal degradation kinetic parameters were determined using Coats-Redfern's and Freeman and Carroll methods. The evolved gas analysis indicated that the CH4 was consumed by the reduction of some oxides in ASR. The reduction reactions and the presence of Ti, silicates, C and N in ASR at 1550°C favor the formation of specific ceramics such as TiN and SiC. The presence of nano-ceramics along with a highly-crystalline graphitic carbon in the pyrolysis residues obtained at 1550°C was confirmed by scanning electron microscopy (SEM), X-ray powder diffraction (XRD) and Raman imaging microscope (RIM) analyses.

  14. 78 FR 20640 - Polychlorinated Biphenyls (PCBs); Recycling Plastics from Shredder Residue

    Science.gov (United States)

    2013-04-05

    ... AGENCY Polychlorinated Biphenyls (PCBs); Recycling Plastics from Shredder Residue AGENCY: Environmental... will generally allow for the recycling of plastic separated from shredder residue under the conditions described in the Voluntary Procedures for Recycling Plastics from Shredder Residue, relying principally...

  15. Life cycle assessment of shredder residue management

    DEFF Research Database (Denmark)

    Boldrin, Alessio; Damgaard, Anders; Brogaard, Line Kai-Sørensen

    This report provides a life-cycle assessment (LCA) of the treatment of shredder residue (SR) in Denmark. The LCA was conducted for the Environmental Protection Agency by DTU Environment in the period March-July 2014, as part of a service agreement between the Danish Environmental Protection Agency...... wood waste, wood waste for recycling and district heating pipes. The LCA was conducted using the EASETECH LCA model developed by DTU Environment for the environmental assessment of waste management systems and environmental technologies. The LCA was conducted in accordance with the LCA principles...

  16. End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.

    Energy Technology Data Exchange (ETDEWEB)

    Jody, B. J.; Daniels, E. J.; Energy Systems

    2007-03-21

    Each year, more than 50 million vehicles reach the end of their service life throughout the world. More than 95% of these vehicles enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, about 75% of automotive materials are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processors recover metal scrap from automobiles involves shredding the obsolete automobiles, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials (about 25% of the weight of the vehicle)--commonly called shredder residue--is disposed of in landfills. Over the past 10 to 15 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles (ELVs), including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has focused on developing technology to recover materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lighter-weight materials--primarily polymers and polymer composites--will be used in manufacturing these vehicles. These materials increase the percentage of shredder residue that must be disposed of, compared with the percentage of metals. Therefore, as the complexity of automotive materials and systems increases, new technologies will be required to sustain and maximize the ultimate recycling of these materials and systems at end-of-life. Argonne National Laboratory (Argonne), in cooperation

  17. 77 FR 74006 - Polychlorinated Biphenyls (PCBs); Recycling Plastics From Shredder Residue

    Science.gov (United States)

    2012-12-12

    ... AGENCY Polychlorinated Biphenyls (PCBs); Recycling Plastics From Shredder Residue AGENCY: Environmental..., Plastic, Polychlorinated biphenyls, Recycling, Shredder residue. ] Dated: November 29, 2012. Louise P... certain food contact and medical applications, these recycled plastics are not expected to make large...

  18. Leaching behavior of persistent organic pollutants (POPs) in shredder residues.

    Science.gov (United States)

    Sakai, S; Urano, S; Takatsuki, H

    1998-01-01

    It is well known that some kinds of waste contain persistent organic pollutants (POPs) such as PCDD/DFs and PCBs. Leaching behaviors of these chemicals, however, have not been focused so much because of their low leachability. On the other hand, shredder residues originated from automobiles and electric appliances consist mainly of plastics, such as PVC, which contain additives including DEHP. In this study, contents analyses and leaching tests with and without surfactant-like substances for shredder residues were conducted. As a result, shredder residues from automobile and electric appliance contained PCBs in ppm level and a quantity of PCDD/DFs. Surfactant-like substances increase the leaching concentration of POPs. DEHP also leached out considerably even though using distilled water.

  19. End-of-life vehicle recycling : state of the art of resource recovery from shredder residue.

    Energy Technology Data Exchange (ETDEWEB)

    Jody, B. J.; Daniels, E. J.; Duranceau, C. M.; Pomykala, J. A.; Spangenberger, J. S. (Energy Systems)

    2011-02-22

    Each year, more than 25 million vehicles reach the end of their service life throughout the world, and this number is rising rapidly because the number of vehicles on the roads is rapidly increasing. In the United States, more than 95% of the 10-15 million scrapped vehicles annually enter a comprehensive recycling infrastructure that includes auto parts recyclers/dismantlers, remanufacturers, and material recyclers (shredders). Today, over 75% of automotive materials, primarily the metals, are profitably recycled via (1) parts reuse and parts and components remanufacturing and (2) ultimately by the scrap processing (shredding) industry. The process by which the scrap processors recover metal scrap from automobiles involves shredding the obsolete automobile hulks, along with other obsolete metal-containing products (such as white goods, industrial scrap, and demolition debris), and recovering the metals from the shredded material. The single largest source of recycled ferrous scrap for the iron and steel industry is obsolete automobiles. The non-metallic fraction that remains after the metals are recovered from the shredded materials - commonly called shredder residue - constitutes about 25% of the weight of the vehicle, and it is disposed of in landfills. This practice is not environmentally friendly, wastes valuable resources, and may become uneconomical. Therefore, it is not sustainable. Over the past 15-20 years, a significant amount of research and development has been undertaken to enhance the recycle rate of end-of-life vehicles, including enhancing dismantling techniques and improving remanufacturing operations. However, most of the effort has been focused on developing technology to separate and recover non-metallic materials, such as polymers, from shredder residue. To make future vehicles more energy efficient, more lightweighting materials - primarily polymers, polymer composites, high-strength steels, and aluminum - will be used in manufacturing these

  20. Characterization of Shredder Residues generated and deposited in Denmark

    DEFF Research Database (Denmark)

    Shabeer Ahmed, Nassera; Wenzel, Henrik; Hansen, Jette Bjerre

    2014-01-01

    This study presents a detailed characterization of Shredder residues (SR) generated and deposited in Denmark from 1990-2010. It represents approximately 85% of total Danish SR. A comprehensive sampling, size fractionation and chemical analysis was carried out on entire samples as well as on each...

  1. Opportunities and Barriers to Resource Recovery and Recycling from Shredder Residue in the United States

    Science.gov (United States)

    Nayak, Naren; Apelian, Diran

    2014-11-01

    Shredder residue is the by-product remaining after ferrous and nonferrous metals have been recovered from the processing of vehicles, white goods, and peddler scrap. Shredder residue consists of glass, plastics, rubber, dirt, and small amounts of metal. It is estimated that 5-7 million tons of this shredder residue are landfilled each year in the United States. Technical advancements, coupled with European Union directives and the economic climate, have transformed the recycling of shredder residue in Europe. In the United States, however, regulatory controls and the cheap cost of landfill have worked against the advancement of recycling and recovery of this resource. The Argonne National Laboratory, which is funded by the U.S. Department of Energy, has investigated the effectiveness of recycling shredder residue into polymers. Other research has examined the use of shredder residue in waste-to-energy applications. To improve our ability to process and recycle shredder residue, an investigation of the regulatory, economic, and technological challenges was undertaken. The objective was to conduct a comprehensive review of work done to date, to document the composition of typical shredder output and to identify potential recoverable items (residual metals, plastics, rubber, foam, etc.). Along with uncovering potential new markets, the research would identify the technical, regulatory, and economic barriers to developing those markets.

  2. Waste conversion into high-value ceramics: Carbothermal nitridation synthesis of titanium nitride nanoparticles using automotive shredder waste.

    Science.gov (United States)

    Mayyas, Mohannad; Pahlevani, Farshid; Maroufi, Samane; Liu, Zhao; Sahajwalla, Veena

    2017-03-01

    Environmental concern about automotive shredder residue (ASR) has increased in recent years due to its harmful content of heavy metals. Although several approaches of ASR management have been suggested, these approaches remain commercially unproven. This study presents an alternative approach for ASR management where advanced materials can be generated as a by-product. In this approach, titanium nitride (TiN) has been thermally synthesized by nitriding pressed mixture of automotive shredder residue (ASR) and titanium oxide (TiO2). Interactions between TiO2 and ASR at non-isothermal conditions were primarily investigated using thermogravimetric analysis (TGA) and differential scanning calorimetry. Results indicated that TiO2 influences and catalyses degradation reactions of ASR, and the temperature, at which reduction starts, was determined around 980 °C. The interaction between TiO2 and ASR at isothermal conditions in the temperature range between 1200 and 1550 °C was also studied. The pressed mixture of both materials resulted in titanium nitride (TiN) ceramic at all given temperatures. Formation kinetics were extracted using several models for product layer diffusion-controlled solid-solid and solid-fluid reactions. The effect of reactants ratio and temperature on the degree of conversion and morphology was investigated. The effect of reactants ratio was found to have considerable effect on the morphology of the resulting material, while temperature had a lesser impact. Several unique structures of TiN (porous nanostructured, polycrystalline, micro-spherical and nano-sized structures) were obtained by simply tuning the ratio of TiO2 to ASR, and a product with appreciable TiN content of around 85% was achieved after only one hour nitridation at 1550 °C.

  3. Thermal valorisation of automobile shredder residue: injection in blast furnace.

    Science.gov (United States)

    Mirabile, Daphne; Pistelli, Maria Ilaria; Marchesini, Marina; Falciani, Roberta; Chiappelli, Lisa

    2002-01-01

    Wastes with residual heating value, according to the trend of the world legislation, could be thermally reused. The present study is conducted to verify the possibility of thermal valorisation of a waste, denominated fluff, by injection in blast furnace. The fluff, arising from the automobile shredder operations, is a waste characterised by a high organic matrix and is potentially dangerous due to the heavy metals, oils filter and halogenated plastics content. The first step of the work is the chemical, physical and toxicological characterisation of this material. Then the fluff injection in a blast furnace tuyere is theoretically analysed with a mathematical model. Finally, experimental trials are conducted in a pilot plant, simulating the most important part of the blast furnace: the raceway, in order to analyse process and industrial aspects. In view of an industrial application a first economical evaluation is carried out on the basis of model and experimental results.

  4. Automobile shredder residue: some recycling, resource recovery and disposal options

    Energy Technology Data Exchange (ETDEWEB)

    Day, M. [National Research Council of Canada, Inst. for Chemical Process and Environmental Technology, Ottawa, ON (Canada)

    2001-07-01

    Obsolete automobiles are the most recycled high-volume consumer product, with a recovery rate of between 75 and 80 per cent by weight. Ferrous scrap metal from old automobiles in North America amounts to about 10 million tons per year. However, each ton of steel that is recovered, produces about 300 kg of automobile shredder residue (ASR), comprised of plastics, rubber, glass, foam, and textiles, contaminated by oil and other fluids. All combined, this represents about 0.3 million tons of waste materials from the 22 shredders in Canada. This amount is likely to increase as the amount of steel in automobiles decreases due to downsizing and weight reduction, emphasizing the need for new resource recovery and application techniques to deal with the ASR problem. This paper describes a number of new initiatives primarily in two areas: separation technologies, ranging from selective disassembly to physical/mechanical/chemical separation processes, and pyrolysis techniques for the recovery of valuable hydrocarbon resources contained in the plastics in the ASR. Recycling of the material into high performance composite materials, such as additives to concrete for increased tensile strength, shrinkage and crack resistance, without adverse effect on other properties such as durability and workability, also received attention. Energy recovery options and engineered landfilling wherein ASR is used as a landfill day cover material, are some other techniques that show considerable promise. In landfill applications the high absorption capacity of ASR for heavy metals such as lead, its high compressibility, erosion resistance, and good traction make it a highly desirable choice for use as day cover material. 25 refs.

  5. Automobile shredder residue : a waste or a resource

    Energy Technology Data Exchange (ETDEWEB)

    Day, M. [National Research Council of Canada, Ottawa, ON (Canada). Inst. for Chemical Process and Environmental Technology

    2000-07-01

    In recent years several recycling and resource recovery technologies have been tested for the challenging task of recycling automobile shredder residues (ASR) with varying degrees of success. ASR is the nonrecyclable residue that remains after recyclable metals are extracted from old automobiles. The use of ASR as a landfill day cover seems to be a viable alternative for this material. Scientific evidence suggests that ASR is capable of acting as a sponge for heavy metals. The absorption capacity of ASR for heavy metal lead was presented along with evaluations for both standard leaching test protocols and dynamic column testing. Compared to soil, ASR has a greater absorption capacity for heavy metals such as lead. ASR also has other desirable features that make it an ideal choice for landfill day cover. For example, ASR provides a stable mat for vehicle traffic, minimizes erosion due to rainfall run off and is less prone to dusting. ASR is also capable of compression to less than 5 cm when overfilled. This conserves landfill volume and allows excavated soil to be used for other purposes. In addition, the use of ASR could prevent contamination of groundwater by preventing the leaching of heavy metals from landfills. 12 refs., 5 tabs., 2 figs.

  6. Evaluation of shredder residue as cement manufacturing feedstock

    Energy Technology Data Exchange (ETDEWEB)

    Boughton, Bob [California Environmental Protection Agency, Department of Toxic Substances Control, Office of Pollution Prevention and Technology Development, 1001 I Street, P.O. Box 806, Sacramento, CA 95812 (United States)

    2007-09-15

    Metal recycling from automobiles, appliances and scrap steel occurs at over 200 dedicated metal shredding operations in the US. Shredder residue (SR) consists of glass, rubber, plastics, fibers, dirt, and fines that remain after ferrous and non-ferrous metals have been removed. Over 3 million tonnes of SR generated in the US each year are landfilled. The results of a previous end-of-life impact assessment showed that use of SR as a fuel supplement for cement manufacturing was environmentally beneficial to the current practice of landfilling and appears better in comparison to the other management methods studied. However, because many reuse and recycling options may not be cost effective, there is a need for further study. Simplistic methods to separate SR into energy and mineral rich streams may facilitate the use of a sizable fraction of SR. Due to the large scale of the cement industry in the US, a significant amount of SR is recoverable. The goal of this study was to identify the feedstock quality parameters needed to satisfy kiln operators and then to assess the mechanical means necessary to process SR into material acceptable as coal and mineral substitutes. Field tests were conducted to separate and beneficiate the coarse SR waste stream. Density separation techniques commonly used by shredders in the past were tested to separate rubber and plastics from non-combustibles and contaminants (e.g., PVC and copper wire). A fraction constituting about 30 wt% of the total SR had fuel characteristics mirroring those of coal. However, remaining levels of potentially problematic constituents (e.g., total chlorine and heavy metals) may limit use to a low relative addition rate at some kilns. An economic review of a full-scale separation system showed that processing SR appears to be economically marginal considering avoided landfilling costs alone. However, significant economic benefits would result from additional non-ferrous metals recovery (namely copper). The

  7. Automobile Shredder Residues in Italy: characterization and valorization opportunities.

    Science.gov (United States)

    Fiore, S; Ruffino, B; Zanetti, M C

    2012-08-01

    At the moment Automobile Shredder Residue (ASR) is usually landfilled worldwide, but European draft Directive 2000/53/CE forces the development of alternative solutions, stating the 95%-wt recovery of an End of Life Vehicle (ELV) weight to be fulfilled by 2015. This work describes two industrial tests, each involving 250-300 t of ELVs, in which different pre-shredding operations were performed. The produced ASR materials underwent an extended characterization and some post-shredding processes, consisting of dimensional, magnetic, electrostatic and densimetric separation phases, were tested on laboratory scale, having as main purpose the enhancement of ASR recovery/recycling and the minimization of the landfilled fraction. The gathered results show that accurate depollution and dismantling operations are mandatory to obtain a high quality ASR material which may be recycled/recovered and partially landfilled according to the actual European Union regulations, with particular concern for Lower Heating Value (LHV), heavy metals content and Dissolved Organic Carbon (DOC) as critical parameters. Moreover post-shredding technical solutions foreseeing minimum economic and engineering efforts, therefore realizable in common European ELVs shredding plants, may lead to multi-purposed (material recovery and thermal valorization) opportunities for ASR reuse/recovery.

  8. Studies on pyrolysis and gasification of automobile shredder residue in China.

    Science.gov (United States)

    Ni, Feijian; Chen, Ming

    2014-10-01

    With increasing automobile ownerships in China, the number of end-of-life vehicles has also rapidly increased. However, the automobile shredder residue generated during the dismantling of end-of-life vehicles in China is not treated properly and has caused great resource waste and environmental problems. In this work, automobile shredder residue from a domestic end-of-life vehicles dismantling company was comprehensively studied through element analysis, combustion heat experiment, proximate analysis, and thermogravimetric analysis. The feasibility of using pyrolysis combined with gasification to treat and recycle automobile shredder residue was investigated. The produced gas, oil, and residue yield was measured and the correlation between their yield and the experimental temperature and ratio of air to automobile shredder residue feed was studied. It is found that when ratio of air and experimental temperature are 1.5 mol kg(-1) and 900 °C, respectively, the heat energy of the gas produced per kilogram treated automobile shredder residue reaches a maximum value of 11.28 MJ. The characteristics of pyrolysis oil and solid residue were studied. The solid residue takes up 4.65%~5.57% of the original end-of-life vehicles weight. This greatly helps to reach the target of a 95% recycling rate.

  9. Co-combustion of automotive shredder residue (ASR) and sewage sludge with a mixture of industrial and household waste in an 20MW fluidized bed combustor; Samfoerbraenning av bilfluff, roetslam och avfall i en 20 MW fluidbaeddpanna - Studier av braenslesammansaettningens paaverkan paa belaeggningsbildning

    Energy Technology Data Exchange (ETDEWEB)

    Eskilsson, David; Johansson, Andreas; Johansson, Linda; Wikstroem-Blomqvist, Evalena

    2007-07-01

    In order to prevent a further increased use of resources and to decrease the environmental impact from landfills, organic wastes are today diverted towards material and energy recovery. This creates a waste market with an increasing number of waste fractions that needs to be treated properly. As an example, in Sweden it has recently been prohibited to landfill source separated combustible waste (2002) and organic waste (2005). Wastes as automotive shredder residue (ASR) and sewage sludge can no longer be landfilled and needs to be either material or energy recovered, which challenge the waste treatment sector. This work investigates the effects of ASR and sewage sludge co-combustion in a 20 MW Energy-from-Waste plant (bubbling fluidised bed). The long term objective of the work is to increase the fuel flexibility, the boiler availability and the power production. This report focus on boiler operation and combustion performance in terms of agglomeration, deposit rates and emissions. In addition to the tests with ASR and sewage sludge, repeated measurements were performed during normal load as a reference. The results show that the co-combusted fractions of ASR and sewage sludge, which on mass basis constituted 6 % and 15 % respectively, did not increase the risk for agglomeration or deposits on heat-exchanging surfaces. Instead, compared to the two reference cases, the deposit rates decreased when sewage sludge was added. Only minor variation in the emissions was seen between the different cases. The levels of I-TEQs were far below the legislated values in all cases

  10. Pyrolysis and gasification-melting of automobile shredder residue.

    Science.gov (United States)

    Roh, Seon Ah; Kim, Woo Hyun; Yun, Jin Han; Min, Tae Jin; Kwak, Yeon Ho; Seo, Yong Chil

    2013-10-01

    Automobile shredder residue (ASR) from end-of-life vehicles (ELVs) in Korea has commonly been disposed of in landfills. Due to the growing number of scrapped cars and the decreasing availability of landfill space, effective technology for reducing ASR is needed. However ASR is a complex mixture, and finding an appropriate treatment is not easy on account of the harmful compounds in ASR. Therefore, research continues to seek an effective treatment technology. However most studies have thus far been performed in the laboratory, whereas few commercial and pilot studies have been performed. This paper studies the pyrolysis and gasification-melting of ASR. The pyrolyis characteristics have been analyzed in a thermogravimetric analyzer (TGA), a Lindberg furnace, and a fixed-bed pyrolyzer to study the fundamental characteristics of ASR thermal conversion. As a pilot study, shaft-type gasification-melting was performed. High-temperature gasification-melting was performed in a 5000 kg/day pilot system. The gas yield and syngas (H2 and CO) concentration increase when the reaction temperature increases. Gas with a high calorific value of more than 16,800 kJ/m3 was produced in the pyrolyzer. From the gasification-melting process, syngas of CO (30-40%) and H2(10-15%) was produced, with 5% CH4 produced as well. Slag generation was 17% of the initial ASR, with 5.8% metal content and 4% fly ash. The concentration of CO decreases, whereas the H2, CO2, and CH4 concentrations increase with an increase in the equivalence ratio (ER). The emission levels of dioxin and air pollution compounds except nitrogen oxides (NO(x)) were shown to satisfy Korean regulations.

  11. Upgrading of automobile shredder residue via innovative granulation process 'ReGran'.

    Science.gov (United States)

    Holthaus, Philip; Kappes, Moritz; Krumm, Wolfgang

    2017-01-01

    Stricter regulatory requirements concerning end-of-life vehicles and rising disposal costs necessitate new ways for automobile shredder residue utilisation. The shredder granulate and fibres, produced by the VW-SICON-Process, have a high energy content of more than 20 MJ kg(-1), which makes energy recovery an interesting possibility. Shredder fibres have a low bulk density of 60 kg m(-3), which prevents efficient storing and utilisation as a refuse-derived fuel. By mixing fibres with plastic-rich shredder granulate and heating the mixture, defined granules can be produced. With this 'ReGran' process, the bulk density can be enhanced by a factor of seven by embedding shredder fibres in the partially melted plastic mass. A minimum of 26-33 wt% granulate is necessary to create enough melted plastic. The process temperature should be between 240 °C and 250 °C to assure fast melting while preventing extensive outgassing. A rotational frequency of the mixing tool of 1000 r min(-1) during heating and mixing ensures a homogenous composition of the granules. During cooling, lower rotational frequencies generate bigger granules with particles sizes of up to 60 mm at 300 r min(-1). To keep outgassing to a minimum, it is suggested to melt shredder granulate first and then add shredder fibres. Adding coal, wood or tyre fluff as a third component reduces chlorine levels to less than 1 wt%. The best results can be achieved with tyre fluff. In combination with the VW-SICON-Process, ReGran produces a solid recovered fuel or 'design fuel' tailored to the requirements of specific thermal processes.

  12. Valorization of Automotive Shredder Residues in metallurgical furnaces

    OpenAIRE

    Guignot, Sylvain; Menad, Noureddine; Diot, F.; Kanari, N.; Save, Maurice; Wavrer, Philippe; Bodénan, Françoise; Thomas, Fabien; Silvente, Eric; Lecler, Marie-Thérèse; Quatravaux, Thibault; Philippe, Russo; Kleihauser, Jens; Buffoni, Corinne

    2011-01-01

    Poster présenté au congrès Euromat 2011; International audience; According to the directive n°2000/53/CE 85 % by weight of an end-of-life vehicle (EVL) must be recycled. The current state of practice comprises four steps. Liquids from battery, gearboxes casing, brake fluid, coolant and air conditioning circuit are first collected. Tyres, catalysts, windscreens and windows are then manually removed, prior to the shredding of the car. A magnetic separation is processed on the shredded materials...

  13. Valorization of Automotive Shredder Residues in metallurgical furnaces

    OpenAIRE

    Guignot, Sylvain; Menad, Noureddine; Diot, F.; Kanari, N.; Save, Maurice; Wavrer, Philippe; Bodénan, Françoise; Thomas, Fabien; Silvente, Eric; Lecler, Marie-Thérèse; Quatravaux, Thibault; Philippe, Russo; Kleihauser, Jens; Buffoni, Corinne

    2011-01-01

    Poster présenté au congrès Euromat 2011; International audience; According to the directive n°2000/53/CE 85 % by weight of an end-of-life vehicle (EVL) must be recycled. The current state of practice comprises four steps. Liquids from battery, gearboxes casing, brake fluid, coolant and air conditioning circuit are first collected. Tyres, catalysts, windscreens and windows are then manually removed, prior to the shredding of the car. A magnetic separation is processed on the shredded materials...

  14. End-of-life vehicles processing, towards a thermal treatment of auto shredder residue

    Institute of Scientific and Technical Information of China (English)

    Thomas Baranger; CHEN Ming; WANG Lu

    2011-01-01

    All over the world, the management of End-of-life Vehicles (ELV) and Automobile Shredder Residue ( ASR ) is an increasing issue for the car industry. The selting up of several environmental directives, among others the notion of extended producer responsibility, encourage car manufacturers to find alternatives solutions to waste disposal. For 2017, China aims for, the recyclability and energy trcovery of 95% of total weight of used cars, and in order to reach this role, the development of some ASR thermal processes could be envisaged. With this research, an overview of ElV, management was given and the different solutions about ASR thermtal treatment were presented. It is showed that in spite of its big heterogeneity, the high heating value of ASR makes pyrolysis and gasification very interesting, compared to incineration or disposal of in landfills.

  15. TG-MS study of the thermo-oxidative behavior of plastic automobile shredder residues.

    Science.gov (United States)

    Guo, Qingjie; Zhang, Xuan; Li, Chao; Liu, Xinmin; Li, Jinhui

    2012-03-30

    Automobile shredder residues (ASR) are materials that are rejected in the metal recovery process for end-of-life vehicles (ELV). These residues are composed of such materials as plastics, foams, glasses, rubbers, textiles, remaining metals and soils. ASR disposal is a difficult task, due to increasingly restrictive re-use policies. The pyrolytic reuse of ASR is one important option for energy recovery. The gas release behavior of pyrolyzed ASR was measured using a TG-MS apparatus, and this thermo-oxidative process was observed under different N(2)/O(2) volume ratios. The final weight/initial residue weight ratio for pyrolyzed ASR decreased from 43.4% to 10.1% with increasing oxygen concentrations. The production rates of hydrogen, methane and carbon dioxide also varied with different N(2)/O(2) volume ratios. The maximum emission of hydrogen and methane occurred when the thermo-oxidative atmosphere was entirely N(2). Temperature had a positive impact on hydrogen production, and the methane emission ratio reached a peak at the second shoulder of the devolatilization stage during which stage organic polymers were emitted. A peculiar characteristic of ASR is its content of nitrogen. The effects of ASR nitrogen content on N(2)O and NO(X) emissions were investigated in detail. NH(3) was the dominant nitrogen species that was released during ASR pyrolysis. N(2)O is highly temperature-sensitive and decomposes to N(2) at temperatures greater than 900°C.

  16. Recycling of automobile shredder residue with a microwave pyrolysis combined with high temperature steam gasification.

    Science.gov (United States)

    Donaj, Pawel; Yang, Weihong; Błasiak, Włodzimierz; Forsgren, Christer

    2010-10-15

    Presently, there is a growing need for handling automobile shredder residues--ASR or "car fluff". One of the most promising methods of treatment ASR is pyrolysis. Apart of obvious benefits of pyrolysis: energy and metals recovery, there is serious concern about the residues generated from that process needing to be recycled. Unfortunately, not much work has been reported providing a solution for treatment the wastes after pyrolysis. This work proposes a new system based on a two-staged process. The ASR was primarily treated by microwave pyrolysis and later the liquid and solid products become the feedstock for the high temperature gasification process. The system development is supported within experimental results conducted in a lab-scale, batch-type reactor at the Royal Institute of Technology (KTH). The heating rate, mass loss, gas composition, LHV and gas yield of producer gas vs. residence time are reported for the steam temperature of 1173 K. The sample input was 10 g and the steam flow rate was 0.65 kg/h. The conversion reached 99% for liquids and 45-55% for solids, dependently from the fraction. The H(2):CO mol/mol ratio varied from 1.72 solids and 1.4 for liquid, respectively. The average LHV of generated gas was 15.8 MJ/Nm(3) for liquids and 15 MJ/Nm(3) for solids fuels.

  17. Recycling of a fine, heavy fluff automobile shredder residue by density and differential fragmentation.

    Science.gov (United States)

    Gent, M R; Menéndez, M; Muñiz, H; Torno, S

    2015-09-01

    A compilation of the physical properties of materials which might typically occur in automobile shredder residue and an analysis of their suitability for the separation of materials in fine (<15mm) heavy fluff ASR (fhf-ASR) is presented. Differences in density and resistance to crushing of fhf-ASR materials were identified as potentially the most suitable low cost, technologically simple means for the separating this waste into its three principal components - metals, minerals (glass/stones) and organics (plastics). Results presented of laboratory scale tests demonstrate that fhf-ASR can in large part be separated into three principal components. Tests were conducted with 0.63-2.0mm and 2-10mm fractions. Recovery of plastics by density separations were conducted with water only jigs for the 2-10mm fraction and shaker tables for the 0.63-2mm fraction. Comparisons are presented of the separations of glass and stones from metals obtained by linear screening and vibratory screening of roller mill and impact mill crushing products of the high density 2-10mm fraction. Equipment used for these tests are of a laboratory or demonstrative scale. It is reasonable to anticipate that industrial scale processing would produce significantly better results. The 2-15mm fraction was found to constitute 91.6% of the fhf-ASR sampled. The metals content of the 2-10mm portion of this fraction was upgraded from 2.5% to 31% and 76.9% with recoveries varying inversely with grade from 91.9% to 40.1%. From 63.6% to 17.1% with a recovery of 93.5% of the organic materials. A residual product of fine sand of crushed glass/stones of 99.4% purity recovered 71.3% of these.

  18. Separation of polyvinyl chloride (PVC) from automobile shredder residue (ASR) by froth flotation with ozonation

    Energy Technology Data Exchange (ETDEWEB)

    Reddy, Mallampati Srinivasa [Department of Chemical Engineering, Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527 (Japan)]. E-mail: srireddys@hiroshima-u.ac.jp; Kurose, Keisuke [Department of Chemical Engineering, Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527 (Japan); Okuda, Tetsuji [Environmental Research and Management Center, Hiroshima University, 1-5-3 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8513 (Japan); Nishijima, Wataru [Environmental Research and Management Center, Hiroshima University, 1-5-3 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8513 (Japan); Okada, Mitsumasa [Department of Chemical Engineering, Graduate School of Engineering, Hiroshima University, 1-4-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8527 (Japan)

    2007-08-25

    The purpose of this study is to develop froth flotation to separate polyvinyl chloride (PVC) from automobile shredder residue (ASR) plastic mixtures of variable composition. Some polymers in ASR polymer mixtures have similar density and hydrophobicity with PVC and thus selective flotation of PVC from ASR polymer mixtures cannot be achieved. The present study focused on the surface modification of PVC with ozonation, and then the modified PVC can be separated from other polymers by the following froth flotation. The results of this study indicate that the selective recovery of PVC from real ASR polyethylene tetra pethelate (PET), polymethyl methacrylate (PMMA), polybutyl methacralate (PBMA), ethyl acrylate (EA), polycarbonate (PC) and rubber mixtures can be accomplished in a three-step process involving a gravity separation, ozonation and froth flotation. The rubber was removed from other heavy ASR (PVC, PET, PMMA, PBMA, EA and PC) polymers by froth flotation without mixing. It was found that ozonation process produced the desired difference in contact angle required (from 89.5 to 73.0{sup o}) for separation of PVC from other heavy ASR polymers, whereas the contact angles of other polymers was slightly decreased. The most of the load ASR, i.e. about 72.4% is floated away and 27.6% was settled down. The highest component 96.7% of PVC was recovered in the settled fraction. As a result of this research effort, the surface modification of PVC with ozonation can be efficiently useful to separate the PVC from other similar density ASR mixed polymers.

  19. Strategies for the enhancement of automobile shredder residues (ASRs) recycling: results and cost assessment.

    Science.gov (United States)

    Ruffino, Barbara; Fiore, Silvia; Zanetti, Maria Chiara

    2014-01-01

    With reference to the European regulation about the management of End-of-Life Vehicles (ELVs), Directive 2000/53/EC imposes the achievement of a recycling target of 85%, and 95% of total recovery by 2015. Over the last few years many efforts have been made to find solutions to properly manage the waste coming from ELVs with the aim of complying with the targets fixed by the Directive. This paper focuses on the economical evaluation of a treatment process, that includes physical (size and density), magnetic and electrical separations, performed on the light fraction of the automobile shredder residue (ASR) with the aim of reducing the amount of waste to dispose of in a landfill and enhancing the recovery of valuable fractions as stated by the EU Directive. The afore mentioned process is able to enhance the recovery of ferrous and non-ferrous metals of an amount equal to about 1% b.w. (by weight) of the ELV weight, and to separate a high energetic-content product suitable for thermal valorization for an amount close to (but not higher than) 10% b.w. of the ELV weight. The results of the economical assessment led to annual operating costs of the treatment ranging from 300,000 €/y to 350,000 €/y. Since the considered plant treats about 13,500 metrictons of ASR per year, this would correspond to an operating cost of approximately 20-25 €/t. Taking into account the amount and the selling price of the scrap iron and of the non magnetic metal recovered by the process, thus leading to a gain of about 30 €/t per ton of light ASR treated, the cost of the recovery process is balanced by the profit from the selling of the recovered metals. On the other hand, the proposed treatment is able to achieve the fulfillment of the targets stated by Directive 2000/53/EC concerning thermal valorization and reduce the amount of waste generated from ELV shredding to landfill.

  20. Pollution control and metal resource recovery for low grade automobile shredder residue: a mechanism, bioavailability and risk assessment.

    Science.gov (United States)

    Singh, Jiwan; Lee, Byeong-Kyu

    2015-04-01

    Automobile shredder residue (ASR) is considered as hazardous waste in Japan and European countries due to presence of heavy metals. This study was carried on the extraction characteristics of heavy metals (Mn, Fe, Ni, and Cr) from automobile shredder residue (ASR). The effects of pH, temperature, particle size, and liquid/solid ratio (L/S) on the extraction of heavy metals were investigated. The recovery rate of Mn, Fe, Ni, and Cr increased with increasing extraction temperature and L/S ratio. The lowest pH 2, the highest L/S ratio, and the smallest particle size showed the highest recovery of heavy metals from ASR. The highest recovery rates were in the following order: Mn > Ni > Cr > Fe. Reduction of mobility factor for the heavy metals was observed in all the size fractions after the recovery. The results of the kinetic analysis for various experimental conditions supported that the reaction rate of the recovery process followed a second order reaction model (R(2) ⩾ 0.95). The high availability of water-soluble fractions of Mn, Fe, Ni, and Cr from the low grade ASR could be potential hazards to the environment. Bioavailability and toxicity risk of heavy metals reduced significantly with pH 2 of distilled water. However, water is a cost-effective extracting agent for the recovery of heavy metals and it could be useful for reducing the toxicity of ASR.

  1. Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent.

    Science.gov (United States)

    Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh; Lee, Byeong-Kyu; Mitoma, Yoshiharu; Mallampati, Srinivasa Reddy

    2015-10-15

    This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO4 dispersion mixture immobilized 95-100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO4 was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO4 mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO4- associated crystalline complexes, and that immobile Ca/PO4 salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO4 as a simple, suitable and highly efficient material for the gentle immobilization of heavy metals in hazardous ASR thermal residue in dry condition.

  2. Innovative market-based policy instruments for waste management: A case study on shredder residues in Belgium.

    Science.gov (United States)

    Dubois, Maarten; Hoogmartens, Rob; Van Passel, Steven; Van Acker, Karel; Vanderreydt, Ive

    2015-10-01

    In an increasingly complex waste market, market-based policy instruments, such as disposal taxes, can give incentives for sustainable progress while leaving flexibility for innovation. However, implementation of disposal taxes is often criticised by domestic waste handlers that fear to be outcompeted by competitors in other countries. The article discusses three innovative market-based instruments that limit the impact on international competitiveness: Tradable recycling credits, refunded disposal taxes and differentiated disposal taxes. All three instruments have already been implemented for distinct environmental policies in Europe. In order to illustrate how these instruments can be used for waste policy, the literature review is complemented with a case study on shredder residues from metal-containing waste streams in Belgium. The analysis shows that a conventional disposal tax remains the most efficient, simple and transparent instrument. However, if international competition is a significant issue or if political support is weak, refunded and differentiated disposal taxes can have an added value as second-best instruments. Tradable recycling credits are not an appropriate instrument for use in small waste markets with market power. In addition, refunded taxes create similar incentives, but induce lower transactions costs. © The Author(s) 2015.

  3. Hydrometallurgical recovery of heavy metals from low grade automobile shredder residue (ASR): An application of advanced Fenton process (AFP).

    Science.gov (United States)

    Singh, Jiwan; Lee, Byeong-Kyu

    2015-09-15

    To investigate the leaching and recovery of heavy metals from low-grade automobile shredder residue (ASR), the effects of nitric acid (HNO3) and hydrogen peroxide (H2O2) concentrations, liquid/solid (L/S) ratio, leaching temperature and ASR particle size fractions on the heavy metal leaching rate were determined. The heavy metals were recovered by fractional precipitation and advanced Fenton process (AFP) at different pHs. The toxicity characteristic leaching procedure (TCLP) test was also performed in the residue remaining after heavy metal leaching to evaluate the potential toxicity of ASR. The heavy metal leaching efficiency was increased with increasing HNO3 and H2O2 concentrations, L/S ratio and temperature. The heavy metal leaching efficiencies were maximized in the lowest ASR size fraction at 303 K and L/S ratio of 100 mL/g. The kinetic study showed that the metal leaching was best represented by a second-order reaction model, with a value of R(2) > 0.99 for all selected heavy metals. The determined activation energy (kJ/mol) was 21.61, 17.10, 12.15, 34.50, 13.07 and 11.45 for Zn, Fe, Ni, Pb, Cd and Cr, respectively. In the final residue, the concentrations of Cd, Cr and Pb were under their threshold limits in all ASR size fractions. Hydrometallurgical metal recovery was greatly increased by AFP up to 99.96% for Zn, 99.97% for Fe, 95.62% for Ni, 99.62% for Pb, 94.11% for Cd and 96.79% for Cr. AFP is highly recommended for the recovery of leached metals from solution even at low concentrations.

  4. Evaluation of heavy metals in hazardous automobile shredder residue thermal residue and immobilization with novel nano-size calcium dispersed reagent

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Chi-Hyeon; Truc, Nguyen Thi Thanh [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Lee, Byeong-Kyu, E-mail: bklee@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of); Mitoma, Yoshiharu [Department of Environmental Sciences, Prefectural University of Hiroshima, 562 Nanatsuka-Cho Shobara City, Hiroshima 727-0023 (Japan); Mallampati, Srinivasa Reddy, E-mail: srireddys@ulsan.ac.kr [Department of Civil and Environmental Engineering, University of Ulsan, Daehak-ro 93, Nam-gu, Ulsan 680-749 (Korea, Republic of)

    2015-10-15

    Graphical abstract: Schematic representation of possible mechanisms determining the heavy metals immobilization efficiencyof ASR dust/thermal residues after treatment with nanometallic Ca/CaO/PO{sub 4}. - Highlights: • Nanometallic Ca/CaO/PO{sub 4} for heavy metals immobilization in ASR residue. • Heavy metals immobilization in dry condition attained about 95–100%. • Remaining heavy metals were lower than the Korean standard regulatory limit. • The amounts of heavy metals detectable on the ASR dust surface decreased. • Nanometallic Ca/CaO/PO{sub 4} has a promising potential for heavy metal remediation. - Abstract: This study was conducted to synthesize and apply a nano-size calcium dispersed reagent as an immobilization material for heavy metal-contaminated automobile shredder residues (ASR) dust/thermal residues in dry condition. Simple mixing with a nanometallic Ca/CaO/PO{sub 4} dispersion mixture immobilized 95–100% of heavy metals in ASR dust/thermal residues (including bottom ash, cavity ash, boiler and bag filter ash). The quantity of heavy metals leached from thermal residues after treatment by nanometallic Ca/CaO/PO{sub 4} was lower than the Korean standard regulatory limit for hazardous waste landfills. The morphology and elemental composition of the nanometallic Ca/CaO-treated ASR residue were characterized by field emission scanning election microscopy combined with electron dispersive spectroscopy (FE-SEM/EDS). The results indicated that the amounts of heavy metals detectable on the ASR thermal residue surface decreased and the Ca/PO{sub 4} mass percent increased. X-ray diffraction (XRD) pattern analysis indicated that the main fraction of enclosed/bound materials on ASR residue included Ca/PO{sub 4}− associated crystalline complexes, and that immobile Ca/PO{sub 4} salts remarkably inhibited the desorption of heavy metals from ASR residues. These results support the potential use of nanometallic Ca/CaO/PO{sub 4} as a simple, suitable and

  5. 火焰原子吸收光谱法测定汽车破碎残渣中重金属含量%Determination of Heavy Metals in Automobile Shredder Residues by Flame Atomic Absorption Spectrometry

    Institute of Scientific and Technical Information of China (English)

    梁莎; 彭绍洪; 曾英

    2013-01-01

    采用低温酸溶、脱氯结合高温干法灰化的方法消解汽车破碎残渣(Automotive Shredder Residues,ASR),讨论了样品消解过程中灰化时间、处理温度、酸的类型等条件对重金属的溶解及挥发损失的影响,获得了ASR样品的最佳消解条件,并利用火焰原子吸收光谱法测定了消解液中重金属Cu、Cd、Pb、Zn、Ni和Cr的含量,考察了各元素的干扰情况以及方法的检出限、准确度和精密度.研究结果表明,先加硝酸,再加硫酸,然后在350℃热解除去氯化氢,再高温(550℃)灰化,最后加浓硝酸和氢氟酸溶解灰化残渣,能够有效避免样品消解过程中重金属的损失.方法的检出限分别为0.0040mg/L(Cu)、0.0019 mg/L(Cd)、0.0490 mg/L(Pb)、0.0032 mg/L(Zn)、0.0180mg/L(Ni)、0.0067 mg/L(Cr),加标回收率为98.00%~106.67%,相对标准偏差(RSD)为1.03%~2.84%.

  6. 汽车破碎残余物中PVC处理技术进展%The Progress of PVC Treatment in Automobile Shredder Residues (ASR)

    Institute of Scientific and Technical Information of China (English)

    梁莎; 彭绍洪; 曾英

    2012-01-01

    汽车破碎残余物(Automobile Shredder Residues,ASR)通常定义为报废汽车(End-of-Life Vehicles,ELVs)经去污、拆解、破碎,除去金属后产生的残渣.包含塑料、橡胶、涂料、泡沫、纤维、金属等几十种物质的碎片和粉末,其中塑料最具有回收价值.ASR中含量最多的四种塑料是聚乙烯(PE)、聚丙烯(PP)、聚氯乙稀(PVC)、聚氨酯(PU).在ASR的回收过程中,特别是热解和汽化,PVC中C1的存在将严重影响ASR的回收.文章简要概述了ASR的特性以及国内外PVC的分离及脱氯技术研究进展.

  7. Selective sequential separation of ABS/HIPS and PVC from automobile and electronic waste shredder residue by hybrid nano-Fe/Ca/CaO assisted ozonisation process.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Lee, Byoung Ho; Mitoma, Yoshiharu; Simion, Cristian

    2017-02-01

    The separation of plastics containing brominated flame retardants (BFR) like (acrylonitrile-butadiene-styrene (ABS), high-impact polystyrene (HIPS), and polyvinyl chloride (PVC)) from automobile and electronic waste shredder residue (ASR/ESR) are a major concern for thermal recycling. In laboratory scale tests using a hybrid nano-Fe/Ca/CaO assisted ozonation treatment has been found to selectively hydrophilize the surface of ABS/HIPS and PVC plastics, enhancing ABS wettability and thereby promoting its separation from ASR/ESR by means of froth flotation. The water contact angles, of ABS/HIPS and PVC decreased, about 18.7°, 18.3°, and 17.9° in ASR and about 21.2°, 20.7°, and 20.0° in ESR respectively. SEM-EDS, FT-IR, and XPS analyses demonstrated a marked decrease in [Cl] and a significant increase in the number of hydrophilic groups, such as CO, CO, and (CO)O, on the PVC or ABS surface. Under froth flotation conditions at 50rpm, about 99.1% of combined fraction of ABS/HIPS in ASR samples and 99.6% of ABS/HIPS in ESR samples were separated as settled fraction. After separation, the purity of the recovered combined ABS/HIPS fraction was 96.5% and 97.6% in ASR and ESR samples respectively. Furthermore, at 150rpm a 100% PVC separation in the settled fraction, with 98% and 99% purity in ASR and ESR plastics, respectively. Total recovery of non-ABS/HIPS and PVC plastics reached nearly 100% in the floating fraction. Further, this process improved the quality of recycled ASR/ESR plastics by removing surface contaminants or impurities.

  8. Quantitative analysis and reduction of the eco-toxicity risk of heavy metals for the fine fraction of automobile shredder residue (ASR) using H2O2.

    Science.gov (United States)

    Singh, Jiwan; Yang, Jae-Kyu; Chang, Yoon-Young

    2016-02-01

    Automobile shredder residue (ASR) fraction (size <0.25mm) can be considered as hazardous due to presence of high concentrations of heavy metals. Hydrogen peroxide combined with nitric acid has been used for the recovery of heavy metals (Zn, Cu, Mn, Fe, Ni, Pb, Cd and Cr) from the fine fraction of ASR. A sequential extraction procedure has also been used to determine the heavy metal speciation in the fine fraction of ASR before and after treatment. A risk analysis of the fine fraction of ASR before and after treatment was conducted to assess the bioavailability and eco-toxicity of heavy metals. These results showed that the recovery of heavy metals from ASR increased with an increase in the hydrogen peroxide concentration. A high concentration of heavy metals was found to be present in Cbio fractions (the sum of the exchangeable and carbonate fractions) in the fine fraction of ASR, indicating high toxicity risk. The Cbio rate of all selected heavy metals was found to range from 8.6% to 33.4% of the total metal content in the fine fraction of ASR. After treatment, Cbio was reduced to 0.3-3.3% of total metal upon a treatment with 2.0% hydrogen peroxide. On the basis of the risk assessment code (RAC), the environmental risk values for heavy metals in the fine fraction of ASR reflect high risk/medium risk. However, after treatment, the heavy metals would be categorized as low risk/no risk. The present study concludes that hydrogen peroxide combined with nitric acid is a promising treatment for the recovery and reduction of the eco-toxicity risk of heavy metals in ASR.

  9. Recovery of precious metals from low-grade automobile shredder residue: A novel approach for the recovery of nanozero-valent copper particles.

    Science.gov (United States)

    Singh, Jiwan; Lee, Byeong-Kyu

    2016-02-01

    The presence of precious metals (PMs) in low-grade automobile shredder residue (ASR) makes it attractive for recycling. This study investigated the leaching and recovery characteristics of two PMs (Cu and Ag) and two heavy metals (Mn and Co) from ASR. The effects of H2O2, leaching temperature, liquid to solid (L/S) ratio, and particle size on metal leaching were determined in an aqueous solution of 0.5M nitric acid. The metal leaching rate was increased with increasing nitric acid concentration, amount of H2O2, L/S ratio and temperature. The leaching kinetics was analyzed by using a second-order reaction model. In the analysis of leaching kinetics, the metal leaching data were well fitted (R(2)⩾0.99) with the second-order reaction model. The activation energy (kJ/mol) for metal leaching was 39.6 for Cu, 17.1 for Ag, 17.3 for Mn and 29.2 for Co. Metal recovery was carried out by fractional precipitation with the addition of advanced Fenton's regent. Metal recovery efficiency was increased to 99.95% for Cu, 99.8% for Mn, 90.0% for Ag and 96.46% for Co with the advanced Fenton's regent. In particular, a novel finding of the PM recovery is that Cu can also be recovered directly from the leachate of ASR in the form of zero-valent copper (ZVC) nanoparticles (NPs). Hydrometallurgical recovery of the metals from ASR using nitric acid is highly efficient.

  10. Sewage sludge as additive to reduce the initial fireside corrosion caused by combustion of shredder residues in a waste-fired BFB boiler

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, T.; Pettersson, J.; Johansson, L.G.; Svensson, J.E. [Chalmers Univ. of Technology, Goeteborg (Sweden). Environmental Inorganic Chemistry; Davidsson, K. [SP Technical Research Institute of Sweden, Boraas (Sweden)

    2010-07-01

    Corrosion/deposition field tests have been carried out in a commercial waste-fired BFB boiler using air-cooled probes. The influence of 20% shredder light fraction (SLF), from recovery of metal scrap material, mixed with waste was studied at different material temperatures (280-420 C). In addition, 3% sewage sludge was added to the 20% SLF/waste mixture. The initial deposit and corrosion products were compared to when the normal waste (municipal solid waste and industrial wastes) fuel was used. After 24 hours exposure, the deposits were analyzed as for elemental composition while the corrosion products were characterised by ESEM/EDX and XRD. The results show that combustion of 20% SLF increased the amount of deposition, which in addition contains a larger fraction chlorine. This causes a higher initial corrosion rate. Adding 3% sewage sludge removes the effect of the SLF and deposits and corrosion products were comparable with the ones formed during the reference exposure. The results indicate that the initial fireside corrosion is chlorine induced and no signs of low-melting heavy metals salts were observed in the corrosion products. (orig.)

  11. Polybrominated dibenzo-p-dioxins/ dibenzofurans and polybrominated diphenyl ethers in soil, vegetation, workshop-floor dust, and electronic shredder residue from an electronic waste recycling facility and in soils from a chemical industrial complex in eastern China.

    Science.gov (United States)

    Ma, Jing; Addink, Rudolf; Yun, Sehun; Cheng, Jinping; Wang, Wenhua; Kannan, Kurunthachalam

    2009-10-01

    The formation and release of polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs) from the incineration of electronic wastes (e-waste) that contain brominated flame retardants (BFRs) are a concern. However, studies on the determination of PBDD/Fs in environmental samples collected from e-waste recycling facilities are scarce. In this study, 11 2,3,7,8-substituted PBDD/Fs and 10 polybrominated diphenyl ether (PBDE) congeners were determined in electronic shredder waste, workshop-floor dust soil, and leaves (of plants on the grounds of the facility) from a large-scale e-waste recycling facility and in surface soil from a chemical-industrial complex (comprising a coke-oven plant, a coal-fired power plant, and a chlor-alkali plant) as well as agricultural areas in eastern China. Total PBDD/F concentrations in environmental samples were in the range of 113-818 pg/g dry wt (dw) for leaves, 392-18500 pg/g dw for electronic shredder residues, 716-800000 pg/g dw for soil samples, and 89600-pg/g dw for workshop-floor dust from the e-waste recycling facility and in a range from nondetect (ND) to 427 pg/g dw in soil from the chemical-industrial complex. The highest mean concentrations of total PBDD/Fs were found in soil samples and workshop-floor dust from the e-waste recycling facility. The dioxin-like toxic equivalent (measured as TEQ) concentrations of PBDD/Fs were greater than the TEQs of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) reported in our previous study for the same set of samples. The concentrations of PBDFs were several orders of magnitude higher than the concentrations of PBDDs in samples from the e-waste facility or from soil from the chemical-industrial complex. A significant correlation was found between the concentrations of sigmaPBDD/Fs and sigmaPBDEs (r = 0.769, p waste recycling facilities were higher than the intakes of TEQs contributed by PCDD/ Fs, calculated in our previous study.

  12. Material and energy recovery from Automotive Shredded Residues (ASR) via sequential gasification and combustion.

    Science.gov (United States)

    Viganò, F; Consonni, S; Grosso, M; Rigamonti, L

    2010-01-01

    Shredding is the common end-of-life treatment in Europe for dismantled car wrecks. It produces the so-called Automotive Shredded Residue (ASR), usually disposed of in landfill. This paper summarizes the outcome of a study carried out by Politecnico di Milano and LEAP with the support of Actelios SpA on the prospects of a technology based on sequential gasification and combustion of this specific waste stream. Its application to the treatment of ASR allows the recovery of large fractions of metals as non-oxidized, easily marketable secondary raw materials, the vitrification of most of the ash content and the production of power via a steam cycle. Results show that despite the unfavourable characteristics of ASR, the proposed technology can reach appealing energy performances. Three of four environmental impact indicators and the cumulative energy demand index are favourable, the main positive contributes being electricity production and metal recovery (mainly aluminium and copper). The only unfavourable indicator is the global warming index because, since most of the carbon in ASR comes from fossil sources, the carbon dioxide emissions at the stack of the thermal treatment plant are mainly non-renewable and, at the same time, the avoided biogas production from the alternative disposal route of landfilling is minor.

  13. Effect of Decarburization on the Residual Stresses Produced by Shot Peening in Automotive Leaf Springs

    Science.gov (United States)

    De la Rosa, Claudia E. Flores; Trejo, Martin Herrera; Román, Manuel Castro; López, Eddy Alfaro

    2016-07-01

    The shot peening is used in the leaf springs manufacturing process for producing a compressive residual stress field (CRSF) at and near the surface that improves the fatigue resistance. The resulting CRSF is influenced by the surface ferrite thickness associated with the decarburization. Hence, this work aims to extend the knowledge on the influence of the decarburization on the CRSF for the given shot peening conditions. A study on the laboratory scale was conducted for an SAE 5160 steel grade used in the automotive industry. Next, specimens with different decarburization depths were treated using industrial shot peening, and the resulting CRSF was characterized. The CRSF was found to be influenced by the decarburization depth. It is assumed that the elastic deformation mechanism is predominant at low decarburization depths, followed by a zone in which both the elastic and plastic deformation have competing mechanisms that contribute to the CRSF, and at higher decarburization depths, the dominant mechanism is plastic deformation. The values for σsrs and σmcrs decrease as the decarburized depth increases, and suitable CRSFs were obtained below a decarburization depth of 120 µm in industrial leaves. Furthermore, the prediction based on expressions correlating the measured variables was good in these leaves.

  14. Design of Waste Shredder Machine

    Directory of Open Access Journals (Sweden)

    Asst. Prof. S.Nithyananth

    2014-03-01

    Full Text Available The conventional agro-waste disposal is a traditional and oldest method of waste disposal in which agriculture wastes are dumped as it is to degrade in a particular place for decomposing. As the wastes are dumped as such, it takes more time to degrade and it causes environmental pollution. The waste shredder machine aims to reduce the agro waste and convert it into useful nourishing fertilizer. It decreases the man work making the farm neat and clean. Also it reduces the heap amount of pollution, disease causing agro-wastes and produces a better fertilizer with vermin compost. The waste shredder machine is an attachment as like a ploughing attachment. In the shredder attachment input power and rigid support is provided by a KAMCO Tera-trac 4W tractor by means of PTO (power take off shaft and three point linkage. PTO shaft of the tractor acts as a basic power input and the three point linkage provide a rigid support to the machine. Various kinds of blades are used for chipping and powdering operations like sawing blades, rotatory blades, and triangular shape blades. The blades are mounted on the shaft. The power is transmitted to another shaft by means of pulley and belt. For designing waste shredder machine, Creo parametric 1.0 software is used.

  15. Heterogeneous nano-Fe/Ca/CaO catalytic ozonation for selective surface hydrophilization of plastics containing brominated and chlorinated flame retardants (B/CFRs): separation from automobile shredder residue by froth flotation.

    Science.gov (United States)

    Mallampati, Srinivasa Reddy; Lee, Byoung Ho; Mitoma, Yoshiharu; Simion, Cristian

    2016-12-09

    One method of weakening the inherently hydrophobic surface of plastics relevant to flotation separation is heterogeneous nano-Fe/Ca/CaO catalytic ozonation. Nano-Fe/Ca/CaO-catalyzed ozonation for 15 min efficiently decreases the surface hydrophobicity of brominated and chlorinated flame retardant (B/CFR)-containing plastics (such as acrylonitrile-butadienestyrene (ABS), high-impact polystyrene (HIPS), and polyvinyl chloride (PVC)) in automobile shredder residue (ASR) to such an extent that their flotation ability is entirely depressed. Such a hydrophilization treatment also stimulates the ABS, HIPS, and PVC surface roughness, wetting of the surface, and the thermodynamic equilibrium conditions at the surface and ultimately changes surface polarity. SEM-EDS, AFM, and XPS analyses of the PVC and ABS surfaces demonstrated a marked decrease in [Cl/Br] and a significant increase in the number of hydrophilic groups, such as C-O, C=O, and (C=O)-O. Under froth flotation conditions at 50 rpm, about 99.5 % of ABS and 99.5 % of HIPS in ASR samples settled out, resulting in a purity of 98 and 98.5 % for ABS and HIPS in ASR samples, respectively. Furthermore, at 150 rpm, we also obtained 100 % PVC separation in the settled fraction, with 98 % purity in ASR. Total recovery of non-B/CFR-containing plastics reached nearly 100 % in the floating fraction. The amount of nano-Fe/Ca/CaO reagent employed during ozonation is very small, and additional removal of surface contaminants from the recycled ASR plastic surfaces by ozonation makes the developed process simpler, greener, and more effective.

  16. Use of fine-grained shredder dust as a cement admixture after a melting, rapid-cooling and pulverizing process

    Energy Technology Data Exchange (ETDEWEB)

    Kakimoto, K. [Kyushu Institute of Technology, Fukuoka (Japan). Department of Applied Chemistry; Nakano, Y. [Kyushu Institute of Technology, Fukuoka (Japan). Graduate School, Department of Engineering; Yamasaki, T.; Shimuzu, K.; Idemitsu, T. [Kyushu Institute of Technology, Fukyoka (Japan). Department of Civil Engineering

    2004-12-01

    Shredder dust is a residue, which is removed from valuable ferrous metals found in scrap automobile and electronic waste. It is also an industrial waste byproduct which, under legislation in place since April 1996, must be disposed of in landfill sites. One method of disposing shredder dust is by scorification, however, this is a costly process and therefore impractical. Costs could be reduced if the shredder dust had a valuable use, and, in this paper, the authors examine its effectiveness as a cement admixture. First, molten shredder dust was crushed for use as a cement admixture. However, it was difficult to crush it completely because metallic grains were mixed in with molten shredder dust. These particles were removed by sifting and the molten shredder dust was crushed once again. Eventually, a fine 75 {mu}m and less powder type of slag was obtained. This slag was mixed with Ordinary Portland Cement (OPC) to form a cement mortar and subsequently a mortar test was conducted. From the test results, it was found that the long-term strength of the cement did not deteriorate even when it included 30% by weight of the pulverized molten shredder dust. (author)

  17. Neutron diffraction measurements for the determination of heat treatment effectiveness in generating compressive residual stress in an automotive crown gear

    Science.gov (United States)

    Albertini, G.; Bruno, G.; Fiori, F.; Girardin, E.; Giuliani, A.; Quadrini, E.; Romani, F.

    2000-03-01

    Thermal austenitizing and tempering treatments are being developed in automotive industry to prevent crack initiation and propagation, especially in components where stress intensity factors influence the stress field and ultimately the fatigue life of the component. This is the case of crown gears, where the tooth root typically undergoes impulsive and very high loads which frequently cause cracking if tensile residual stresses are present at the surface. The sign reversal of these stresses is the aim of austenitizing and tempering treatments. In this work neutron diffraction measurements of residual stress (RS) on a UNI55Cr3 steel crown gear, carried out at HMI-BENSC , are presented. The sample was submitted to a new multi-frequency induction technique whose effectiveness was checked. Comparisons with X-ray measurements are shown, and RS measured by X-rays on a similar shot-peened sample are also mentioned. Experiments at HMI-BENSC have received financial support by the European Commission under the TMR/LSF Access Programme (contract no. ERBFMGE CT950060).

  18. 7 CFR 58.708 - Grinders or shredders.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Grinders or shredders. 58.708 Section 58.708 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards....708 Grinders or shredders. The grinders or shredders used in the preparation of the trimmed...

  19. Scrap automotive electronics: A mini-review of current management practices.

    Science.gov (United States)

    Cucchiella, Federica; D'Adamo, Idiano; Rosa, Paolo; Terzi, Sergio

    2016-01-01

    End-of-life vehicles, together with waste from electric and electronic equipment, are known as an important source of secondary raw materials. For many years, their recovery has allowed the restoring of great amounts of metals for new cars production. This article provides a comprehensive mini-review on the end-of-life vehicles recycling topic between 2000 and 2014, with a particular focus on automotive electronics recycling. In fact, in the last years, experts focused their attention on a better exploitation of automotive shredder residue fraction, but not sufficiently on eventual electronic scraps embedded in it. Hence, studies assessing the value embedded in these scraps are rarely available in literature, causing an important gap in both recycling policies and research. The fact that, at present, the management of electronic control units (the most valuable component among automotive electronic equipment) is, as yet, off the radar in both end-of-life vehicles and waste from electric and electronic equipment Directives demonstrates the theory. Of course, their recycling would not contribute in a relevant way to reach the weighted-based recycling and recovery targets characterising current regulations, but would be very important under a critical raw materials recovery view. Results coming from the literature analysis confirm these assumptions.

  20. Challenges and Alternatives to Plastics Recycling in the Automotive Sector

    Directory of Open Access Journals (Sweden)

    Lindsay Miller

    2014-08-01

    Full Text Available Plastics are increasingly a preferred material choice in designing and developing complex, consumer products, such as automobiles, because they are mouldable, lightweight, and are often perceived to be highly recyclable materials. However, actually recycling the heterogeneous plastics used in such durable items is challenging, and presents very different scenarios to how simple products, such as water bottles, are recovered via curbside or container recycling initiatives. While the technology exists to recycle plastics, their feasibility to do so from high level consumer or industrial applications is bounded by technological and economical restraints. Obstacles include the lack of market for recyclates, and the lack of cost efficient recovery infrastructures or processes. Furthermore, there is a knowledge gap between manufacturers, consumers, and end-of-life facility operators. For these reasons, end-of-life plastics are more likely to end up down-cycled, or as shredder residue and then landfilled. This paper reviews these challenges and several alternatives to recycling plastics in order to broaden the mindset surrounding plastics recycling to improve their sustainability. The paper focuses on the automotive sector for examples, but discussion can be applied to a wide range of plastic components from similarly complex products.

  1. Challenges and Alternatives to Plastics Recycling in the Automotive Sector.

    Science.gov (United States)

    Miller, Lindsay; Soulliere, Katie; Sawyer-Beaulieu, Susan; Tseng, Simon; Tam, Edwin

    2014-08-15

    Plastics are increasingly a preferred material choice in designing and developing complex, consumer products, such as automobiles, because they are mouldable, lightweight, and are often perceived to be highly recyclable materials. However, actually recycling the heterogeneous plastics used in such durable items is challenging, and presents very different scenarios to how simple products, such as water bottles, are recovered via curbside or container recycling initiatives. While the technology exists to recycle plastics, their feasibility to do so from high level consumer or industrial applications is bounded by technological and economical restraints. Obstacles include the lack of market for recyclates, and the lack of cost efficient recovery infrastructures or processes. Furthermore, there is a knowledge gap between manufacturers, consumers, and end-of-life facility operators. For these reasons, end-of-life plastics are more likely to end up down-cycled, or as shredder residue and then landfilled. This paper reviews these challenges and several alternatives to recycling plastics in order to broaden the mindset surrounding plastics recycling to improve their sustainability. The paper focuses on the automotive sector for examples, but discussion can be applied to a wide range of plastic components from similarly complex products.

  2. Formation and destruction of Polycyclic Aromatic Hydrocarbons (PAHs in the flaring of the biogas collected from an automotive shredded residues landfill

    Directory of Open Access Journals (Sweden)

    Massimo Raboni

    2016-03-01

    Full Text Available The paper shows the results of the combustion in an enclosed flare of the biogas collected from an automotive shredded residues landfill. The results demonstrate that at 1,000°C and long combustion, several synthesis reactions lead to the formation of 4 to 6 rings of PAHs. This formation also involves the formation of compounds such as benzo(g,h,iperylene, indeno(1,2,3-cdpyrene and dibenzo(a,hanthracene not present in raw biogas. However, the compounds most likely to form in combustion are benzo (a anthracene and benzo (b fluoranthene. The only exception is chrysene which is significantly destroyed. The experience has proved the total lack of formation of PAHs with only 2 and 3 aromatic rings.

  3. Influence of shredder feeding and nutrients on fungal activity and community structure in headwater streams

    Science.gov (United States)

    Namil Chung; Keller. Suberkropp

    2008-01-01

    In stream detrital food webs, interactions occur between aquatic hyphomycetes associated with decomposing leaves and shredders consuming those leaves. However, few studies have examined how the feeding activity of shredders affects aquatic hyphomycetes. We examined the effect of shredder feeding on aquatic hyphomycete communities associated with submerged leaves in two...

  4. Viability study of automobile shredder residue as fuel.

    Science.gov (United States)

    Edo, Mar; Aracil, Ignacio; Font, Rafael; Anzano, Manuela; Fullana, Andrés; Collina, Elena

    2013-09-15

    Car Fluff samples collected from a shredding plant in Italy were classified based on particle size, and three different size fractions were obtained in this way. A comparison between these size fractions and the original light fluff was made from two different points of view: (i) the properties of each size fraction as a fuel were evaluated and (ii) the pollutants evolved when each size fraction was subjected to combustion were studied. The aim was to establish which size fraction would be the most suitable for the purposes of energy recovery. The light fluff analyzed contained up to 50 wt.% fines (particle size<20 mm). However, its low calorific value and high emissions of polychlorinated dioxins and furans (PCDD/Fs), generated during combustion, make the fines fraction inappropriate for energy recovery, and therefore, landfilling would be the best option. The 50-100 mm fraction exhibited a high calorific value and low PCDD/F emissions were generated when the sample was combusted, making it the most suitable fraction for use as refuse-derived fuel (RDF). Results obtained suggest that removing fines from the original ASR sample would lead to a material product that is more suitable for use as RDF.

  5. Polymer Recovery from Auto Shredder Residue by Projectile Separation Method

    Directory of Open Access Journals (Sweden)

    Dong Yang Wu

    2012-04-01

    Full Text Available The number of vehicles on the road has been increasing at an enormous rate over the last decade. By 2015, the number of vehicles that reach the end of their life will be close to a million per year in Australia. Most metallic parts of the vehicle can be recycled but the plastic components and components of other materials are normally shredded and disposed in landfills. As more vehicles are using composite materials, the percentage of materials sent to landfill is alarming. This paper reviews existing polymer recycling techniques for End-of-Life Vehicles (ELVs and proposes a more efficient electrostatic based projectile separation method. The test rig is at the preliminary stage of development and initial outcomes are promising.

  6. Automotive websites

    CERN Document Server

    Jensen, Todd A

    2006-01-01

    For anyone buying a new car, restoring an old favorite, collecting license plates or looking for motorsports information, the internet is the place to go and this is the book to help you get there. Now with over 650 internet addresses, this expanded and updated guide provides detailed descriptions and reviews of the biggest, best and most interesting automotive websites on the net. Beginning with a brief internet history and helpful hints, it aids the novice (or not so novice) user in picking through the countless automotive sites on the internet. Websites are arranged by topics such as afterm

  7. Study of residual stresses in welded joints of dual phase HSLA steel used in automotive industry; Estudo das tensoes residuais em juntas soldadas de aco ARBL bifasico usado na industria automobilistica

    Energy Technology Data Exchange (ETDEWEB)

    Barbato, D.S.; Fonseca, M.P. Cindra; Marques Junior, A.S.; Chuvas, T.C.; Pardal, J.M., E-mail: mcindra@vm.uff.b [Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-graduacao em Engenharia Mecanica; Berretta, J.R. [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2010-07-01

    One way of weight reduction in automotive vehicles is through the use of high strength and low alloy (HSLA) steels, which enables the use of small thickness plates. Whereas the appearance of residual stresses is intrinsic to the welding process, this study evaluates the residual stresses generated in welded joints obtained by TIG and LASER welding processes and comparing them. Residual stresses were measured by X-rays diffraction technique, using a portable device with Cr{kappa}{alpha} radiation applying the double exposure method. It also evaluates the influence of shot peening treatment applied after welding, in the bend tests conducted for both welding conditions and TIG welded joints showed higher stability of compressive stresses after welding. The metallographic analysis by optical microscopy complemented the welded joints characterization. (author)

  8. Toddlers at risk for paper shredder injury in the home: easy access and severe injury.

    Science.gov (United States)

    Warren, Ramona C; Foltin, George L

    2006-02-01

    A 2-year-old girl sustained severe injury to 2 fingers from a home paper shredder. This case illustrates the risk of injury from paper shredders, which are increasingly common household items. Toddlers are at risk of finger injury and amputation. The US Consumer Product Safety Commission performed an investigation of reported injuries and the characteristics of paper shredders that might have contributed to the injuries, and we summarize their findings.

  9. Implementation plan for the processing of shredder waste; Implementatieplan verwerking shredderafval

    Energy Technology Data Exchange (ETDEWEB)

    Nauta, J.P.; Reijnders, H.P.E.M.; Oudhuis, A.B.J. [ECN Energie Efficiency, Petten (Netherlands)

    1998-10-01

    Scenarios for the future processing of (automobile) shredder waste in the Netherlands are discussed. The composition of shredder waste and the supply of such wastes in the Netherlands is dealt with in chapter 2, In chapter 3 processing techniques are presented. Possible sites and organizations to process shredder wastes are outlined in chapter 4, while in chapter 5 licensing and legal aspects are discussed. In chapter 6 the most appropriate processing scenarios are listed

  10. Automotive sensors

    Science.gov (United States)

    Marek, Jiri; Illing, Matthias

    2003-01-01

    Sensors are an essential component of most electronic systems in the car. They deliver input parameters for comfort features, engine and emission control as well as for the active and passive safety systems. New technologies such as silicon micromachining play an important role for the introduction of these sensors in all vehicle classes. The importance and use of these sensor technologies in today"s automotive applications will be shown in this article. Finally an outlook on important current developments and new functions in the car will be given.

  11. 78 FR 5496 - Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain...

    Science.gov (United States)

    2013-01-25

    ... COMMISSION Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain..., certain processes for manufacturing or relating to same and certain products containing same and certain... shredders, certain processes for manufacturing or relating to same and certain products containing same and...

  12. Selective feeding by shredders on leaf-colonizing stream fungi: comparison of macroinvertebrate taxa.

    Science.gov (United States)

    Arsuffi, T L; Suberkropp, K

    1989-04-01

    Laboratory experiments were conducted to examine the effects of fungal species composition of leaf detritus on the feeding of distantly related macroinvertebrate shredders. Preferences of shredders representing three orders of insects (Diptera: Tipulidae; Plecoptera: Pteronarcidae; Trichoptera: Limnephilidae and Calamatoceridae) and one each of gastropods (Basommatophora: Planorbidae) and crustaceans (Amphipoda: Gammaridae) were compared. Shredder preferences were based on consumption of leaves separately colonized by one of eight species of aquatic hyphomycetes. The feeding patterns of the invertebrates ranged from lack of feeding to heavy consumption of fungal-colonized leaves. Where consumption occurred, rank orders of preference and degree of selectivity differed among invertebrate shredders. Differences in preferences together with relationships between degree of selectivity and the relative mobility and digestive specializations exhibited by shredders suggest that the exploitation of fungal-colonized leaf detritus by different taxa is affected by phylogenetic constraints. Our results suggest that fungal species composition affects the feeding of a variety of shredders and that fungal species composition may be as important as degree of conditioning in determining food selection by shredders.

  13. Automotive vehicle sensors

    Energy Technology Data Exchange (ETDEWEB)

    Sheen, S.H.; Raptis, A.C.; Moscynski, M.J.

    1995-09-01

    This report is an introduction to the field of automotive vehicle sensors. It contains a prototype data base for companies working in automotive vehicle sensors, as well as a prototype data base for automotive vehicle sensors. A market analysis is also included.

  14. Recycling used automotive oil filters

    Science.gov (United States)

    Peaslee, Kent D.

    1994-02-01

    Over 400 million used automotive oil filters are discarded in the United States each year, most of which are disposed of in landfills wasting valuable resources and risking contamination of ground- and surface-water supplies. This article summarizes U.S. bureau of Mines research evaluating scrap prepared from used automotive oil filters. Experimental results show that crushed and drained oil filters have a bulk density that is higher than many typical scrap grades, a chemical analysis low in residual elements (except tin due to use of tin plate in filters), and an overall yield, oil-filter scrap to cast steel, of 76% to 85%, depending on the method used to prepare the scrap.

  15. 78 FR 79006 - Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain...

    Science.gov (United States)

    2013-12-27

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain Products Containing Same and Certain Parts Thereof; Commission Determination Not To Review an Initial...

  16. Processing equipment for resource recovery systems. Volume 3: Field test evaluation of shredders

    Science.gov (United States)

    Savage, G. M.; Shiflett, G. R.

    1980-07-01

    A program to test and evaluate large scale shredders used for the size reduction of solid waste is reported. Tests were conducted on seven horizontal hammermills, one vertical hammermill, and one vertical ring shredder at six commercial sites. Both two stage size reduction and single stage size reduction were studied. Analytical relationships among the comminution parameters and the establishment of levels of performance for energy consumption and hammer wear associated with size reduction of solid waste are developed.

  17. Shredder and incinerator technology for treatment of commercial transuranic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Oma, K.H.; Westsik, J.H. Jr.; Ross, W.A.

    1985-10-01

    This report describes the selection and evaluation of process equipment to accomplish the shredding and incineration of commercial TRU wastes. The primary conclusions derived from this study are: Shredding and incineration technology appears effective for converting simulated commercial TRU wastes to a noncombustible form. The gas-heated controlled-air incinerator received the highest technical ranking. On a scale of 1 to 10, the incinerator had a Figure-of-Merit (FOM) number of 7.0. This compares to an FOM of 6.1 for the electrically heated controlled-air incinerator and an FOM of 5.8 for the rotary kiln incienrator. The present worth costs of the incineration processes for a postulated commercial reprocessing plant were lowest for the electrically heated and gas-heated controlled-air incinerators with costs of $16.3 M and $16.9 M, respectively (1985 dollars). Due to higher capital and operating costs, the rotary kiln process had a present worth cost of $20.8 M. The recommended process from the three evaluated for the commercial TRU waste application is the gas-heated controlled-air incinerator with a single stage of shredding for feed pretreatment. This process had the best cost-effectiveness ratio of 1.0 (normalized). The electrically heated controller-air incinerator had a rating of 1.2 and the rotary kiln rated a 1.5. Most of the simulated wastes were easily processed by the low-speed shredders evaluated. The HEPA filters proved difficult to process, however. Wood-framed HEPA filters tended to ride on the cutter wheels and spacers without being gripped and shredded. The metal-framed HEPA filters and other difficult to shred items caused the shredders to periodically reach the torque limit and go into an automatic reversal cycle; however, the filters were eventually processed by the units. All three incinerators were ineffective for oxidizing the aluminum metal used as spacers in HEPA filters.

  18. European Automotive Congress

    CERN Document Server

    Clenci, Adrian

    2016-01-01

    The volume includes selected and reviewed papers from the European Automotive Congress held in Bucharest, Romania, in November 2015. Authors are experts from research, industry and universities coming from 14 countries worldwide. The papers are covering the latest developments in fuel economy and environment, automotive safety and comfort, automotive reliability and maintenance, new materials and technologies, traffic and road transport systems, advanced engineering methods and tools, as well as advanced powertrains and hybrid and electric drives.

  19. Copper oxide nanoparticles can induce toxicity to the freshwater shredder Allogamus ligonifer.

    Science.gov (United States)

    Pradhan, Arunava; Seena, Sahadevan; Pascoal, Cláudia; Cássio, Fernanda

    2012-11-01

    Increased commercialisation of nanometal-based products augments the possibility of their deposition into aquatic ecosystems; this, in turn, may pose risks to aquatic biota and associated ecological functions. Freshwater invertebrate shredders mostly use microbially-colonized plant litter as food resource and play an important role in aquatic detritus food webs. We assessed lethal effects of nanoCuO on the shredder Allogamus ligonifer (Trichoptera, Limnephilidae) by determining the concentration that induced 50% of death (LC(50)), and sublethal effects of nanoCuO on the feeding behaviour and growth of the shredder by exposing the animals to: (i) stream water supplemented with nanoCuO and microbially-colonized leaves, and (ii) stream water (without nanoCuO) and microbially-colonized leaves pre-exposed to nanoCuO. Results from acute lethal tests showed that the 96 h LC(50) of nanoCuO was very high (569 mg L(-1)). In the absence of nanoparticles, leaf consumption rate was 0.27 mg leaf DM mg(-1) animal DM d(-1) and the shredder growth rate was 56 μg animal DM mg(-1) animal DM d(-1). A significant inhibition in leaf consumption rate (up to 47%) and invertebrate growth rate (up to 46%) was observed when shredders were exposed to the higher tested sublethal concentration of nanoCuO (75 mg L(-1)) through either contaminated stream water or pre-contaminated food. The exposure to increased nanoCuO concentration via water or pre-contaminated food led to higher accumulation of copper in the larval body. Leached water-soluble ionic copper from the nanoCuO adsorbed or accumulated in the shredder (up to 10.2% of total Cu) seemed to influence the feeding behaviour and growth of the shredder.

  20. Automotive electronics design fundamentals

    CERN Document Server

    Zaman, Najamuz

    2015-01-01

    This book explains the topology behind automotive electronics architectures and examines how they can be profoundly augmented with embedded controllers. These controllers serve as the core building blocks of today’s vehicle electronics. Rather than simply teaching electrical basics, this unique resource focuses on the fundamental concepts of vehicle electronics architecture, and details the wide variety of Electronic Control Modules (ECMs) that enable the increasingly sophisticated "bells & whistles" of modern designs.  A must-have for automotive design engineers, technicians working in automotive electronics repair centers and students taking automotive electronics courses, this guide bridges the gap between academic instruction and industry practice with clear, concise advice on how to design and optimize automotive electronics with embedded controllers.

  1. On the ASR and ASR thermal residues characterization of full scale treatment plant.

    Science.gov (United States)

    Mancini, G; Viotti, P; Luciano, A; Fino, D

    2014-02-01

    In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material.

  2. National Automotive Center - NAC

    Data.gov (United States)

    Federal Laboratory Consortium — Encouraged by the advantages of collaboration, the U.S. Army Tank Automotive Research, Development and Engineering Center (TARDEC) worked with the Secretary of the...

  3. Automotive stamped part fatigue design

    Directory of Open Access Journals (Sweden)

    Caudoux Mélanie

    2014-06-01

    Full Text Available Fatigue design of automotive axle parts is of prior concern because of these are high safety parts and they are expected to drive the overall vehicle mass reduction. In this framework, the stamping process is widely used to form axle parts, before assembling them by welding. Consequently, the mechanical and physical characteristics of the blank sheet are modified, having a strong influence on the fatigue behavior. In this paper, we address the consequences of the stamped process on the fatigue design and how they may be effectively taken into account in the automotive industry. Actually, the coupling between the stamping process and the fatigue design is under development at PSA Peugeot Citroën Company since several years. Such an analysis deals with some major topics: thickness variation, plastic hardening and deformation, and residual stress. All of these ingredients result in fatigue criteria evolutions: it is important to stress that the stamping process can have advantageous or disadvantageous consequences on the fatigue design. This is here highlighted on some examples, dealing with front and rear axles.

  4. Failure Mechanisms and Structural Optimization of Shredder Hammer for Metal Scraps

    Institute of Scientific and Technical Information of China (English)

    ZHOU Xianyan; HU Zhili; TAO Yijun; QIN Xunpeng; HUA Lin

    2016-01-01

    Recycling retired cars can relieve the environmental pollution and resource waste efficiently. However, a few publications can be found on the failure mechanisms and optimization method of recycling equipment, shredders. Thus, the failure mechanisms and structural optimization of shredder hammers for retired cars are studied aiming improving shredding efficiency and reducing cost. Failure types of shredder hammer are studied theoretically, and it is found that wear failure and fatigue failure are the two main failure types of shredder hammer. The shredding process of metal scraps is analyzed by finite element method, and it can be divided into four stages based on the stress states: initial stage, collision stage, grinding stage and separation stage. It is proved that the shredding efficiency can be improved by increasing cutouts on the hammer head. Finally, it is determined that the hammer with two cutouts is the optimal structure for metal scraps, which can improve the shredding efficiency by 20% and lengthen the hammer life by 15%. This study provides scientific basis for the industry application and theoretical foundation for further research.

  5. Leaf Degradation, Macroinvertebrate Shredders & Energy Flow in Streams: A Laboratory-Based Exercise Examining Ecosystem Processes

    Science.gov (United States)

    Sparkes, Timothy C.; Mills, Colleen M.; Volesky, Lisa; Talkington, Jennifer; Brooke, Joanna

    2008-01-01

    A laboratory-based exercise that demonstrates mechanisms underlying leaf degradation in streams. Students examine the effects of "leaf conditioning" on the feeding behavior of invertebrate shredders. The exercise is completed in two sessions and can be adapted to both high school and college levels.

  6. Assessment of methane production from shredder waste in landfills: The influence of temperature, moisture and metals

    DEFF Research Database (Denmark)

    Fathi Aghdam, Ehsan; Scheutz, Charlotte; Kjeldsen, Peter

    2017-01-01

    In this study, methane (CH4) production rates from shredder waste (SW) were determined by incubation of waste samples over a period of 230days under different operating conditions, and first-order decay kinetic constants (k-values) were calculated. SW and sterilized SW were incubated under...

  7. Growth of shredders on leaf litter biofilms: the effect of light intensity

    NARCIS (Netherlands)

    Franken, R.J.M.; Waluto, B.; Peeters, E.T.H.M.; Gardeniers, J.J.P.; Beijer, J.A.J.; Scheffer, M.

    2005-01-01

    1. The effect of light intensity on the decomposition of poplar (Populus nigra) leaves and growth of the shredders, Asellus aquaticus and Gammarus pulex, was studied in a laboratory experiment. The response was studied along a gradient of six light intensities of 0, 5, 23, 54, 97 and 156 ¿mol m -2 s

  8. Failure mechanisms and structural optimization of shredder hammer for metal scraps

    Science.gov (United States)

    Zhou, Xianyan; Hu, Zhili; Tao, Yijun; Qin, Xunpeng; Hua, Lin

    2016-07-01

    Recycling retired cars can relieve the environmental pollution and resource waste efficiently. However, a few publications can be found on the failure mechanisms and optimization method of recycling equipment, shredders. Thus, the failure mechanisms and structural optimization of shredder hammers for retired cars are studied aiming improving shredding efficiency and reducing cost. Failure types of shredder hammer are studied theoretically, and it is found that wear failure and fatigue failure are the two main failure types of shredder hammer. The shredding process of metal scraps is analyzed by finite element method, and it can be divided into four stages based on the stress states: initial stage, collision stage, grinding stage and separation stage. It is proved that the shredding efficiency can be improved by increasing cutouts on the hammer head. Finally, it is determined that the hammer with two cutouts is the optimal structure for metal scraps, which can improve the shredding efficiency by 20% and lengthen the hammer life by 15%. This study provides scientific basis for the industry application and theoretical foundation for further research.

  9. 77 FR 76518 - Certain Paper Shredders, Certain Processes for Manufacturing or Relating to Same and Certain...

    Science.gov (United States)

    2012-12-28

    ... Processes for Manufacturing or Relating to Same and Certain Products Containing Same and Certain Parts... processes for manufacturing or relating to same and certain products containing same and certain parts.... International Trade Commission has received a complaint entitled Certain Paper Shredders, Certain Processes for...

  10. High integrity automotive castings

    Energy Technology Data Exchange (ETDEWEB)

    Weiss, D. [Eck Industries Inc., St. Manitowoc, WI (United States)

    2007-07-01

    This paper described the High Integrity Magnesium Automotive Casting (HI-MAC) program, which was developed to ensure the widespread adoption of magnesium in structural castings. The program will encourage the use of low pressure permanent molds, squeeze casting, and electromagnetic pumping of magnesium into dies. The HI-MAC program is currently investigating new heat treatment methods, and is in the process of creating improved fluid flow and solidification modelling to produce high volume automotive components. In order to address key technology barriers, the program has been divided into 8 tasks: (1) squeeze casting process development; (2) low pressure casting technology; (3) thermal treatment; (4) microstructure control; (5) computer modelling and properties; (6) controlled molten metal transfer and filling; (7) emerging casting technologies; and (8) technology transfer throughout the automotive value chain. Technical challenges were outlined for each of the tasks. 1 ref., 3 tabs., 5 figs.

  11. Identification for automotive systems

    CERN Document Server

    Hjalmarsson, Håkan; Re, Luigi

    2012-01-01

    Increasing complexity and performance and reliability expectations make modeling of automotive system both more difficult and more urgent. Automotive control has slowly evolved from an add-on to classical engine and vehicle design to a key technology to enforce consumption, pollution and safety limits. Modeling, however, is still mainly based on classical methods, even though much progress has been done in the identification community to speed it up and improve it. This book, the product of a workshop of representatives of different communities, offers an insight on how to close the gap and exploit this progress for the next generations of vehicles.

  12. Automotive NVH technology

    CERN Document Server

    Nijman, Eugenius; Priebsch, Hans-Herwig

    2016-01-01

    This book presents seven chapters examining selected noise, vibration and harshness (NVH) topics that are highly relevant for automotive vehicle development. These include applications following the major trends toward increased passenger comfort, vehicle electrification and lightweight design. The authors of the seven chapters, all of which are experts from the automotive industry and academia, present the foremost challenges and potential solutions in this demanding field. Among others, applications for sound optimization in downsized engines, noise optimization in electric powertrains, weight reduction options for exhaust systems, porous materials description, and the vibro-acoustic analysis of geared systems are discussed.

  13. Automotive component failures

    CSIR Research Space (South Africa)

    Heyes, AM

    1998-06-01

    Full Text Available be expected[ 023 A[ M[ HEYES Fig[ 6[ Low magni_cation fractograph showing the seam defect "S#\\ fatigue area "F# and the brittle fracture area "B#[ Fig[ 7[ Fracture surface marked F in Fig[ 6\\ typical of a fatigue fracture surface in a high strength steel... Ltd[ All rights reserved[ Keywords] Accident investigation\\ automotive failures\\ decarburization\\ fatigue\\ weld fatigue[ 0[ INTRODUCTION Failure of automotive components is an occurrence which a}ects the life of almost every person at one stage...

  14. Bringing Excellence to Automotive

    Science.gov (United States)

    Večeřa, Pavel; Paulová, Iveta

    2012-12-01

    Market situation and development in recent years shows, that organization's ability to meet customer requirements is not enough. Successful organizations are able to exceed the expectations of all stakeholders. They are building their excellence systematically. Our contribution basically how the excellence in automotive is created using EFQM Excellence Model in Total Quality Management.

  15. Personal Achievement Mathematics: Automotive.

    Science.gov (United States)

    Baenziger, Betty

    Utilizing word problems relevant to automotive mechanics, this workbook presents a concept-oriented approach to competency development in 13 areas of basic mathematics: (1) the expression of numbers as figures and words; (2) the addition, subtraction, multiplication, and division of whole numbers, fractions, and decimals; (3) scientific notation;…

  16. Incinerator performance: effects of changes in waste input and furnace operation on air emissions and residues

    DEFF Research Database (Denmark)

    Astrup, Thomas; Riber, Christian; Pedersen, Anne Juul

    2011-01-01

    and residue composition at a full-scale incinerator were affected by known additions of specific waste materials to the normal municipal solid waste (MSW) input. Six individual experiments were carried out (% ww of total waste input): NaCl (0.5%), shoes (1.6%), automobile shredder waste (14%), batteries (0...

  17. CHARACTERIZATION OF EMISSIONS FROM THE SIMULATED OPEN-BURNING OF NON-METALLIC AUTOMOBILE SHREDDER RESIDUE

    Science.gov (United States)

    The report gives results of a study in which the open combustion of a nonmetallic waste product called "fluff" was simulated and the resulting emissions collected and characterized to gain insight into the types and quantities of these air pollutants. (NOTE: The reclamation proce...

  18. Rotordynamics of automotive turbochargers

    CERN Document Server

    Nguyen-Schäfer, Hung

    2015-01-01

    Rotordynamics of automotive turbochargers is dealt with in this book encompassing the widely working field of small turbomachines under real operating conditions at the very high rotor speeds up to 300000 rpm. The broadly interdisciplinary field of turbocharger rotordynamics involves 1) Thermodynamics and Turbo-Matching of Turbochargers 2) Dynamics of Turbomachinery 3) Stability Analysis of Linear Rotordynamics with the Eigenvalue Theory 4) Stability Analysis of Nonlinear Rotordynamics with the Bifurcation Theory 5) Bearing Dynamics of the Oil Film using the Two-Phase Reynolds Equation 6) Computation of Nonlinear Responses of a Turbocharger Rotor 7) Aero and Vibroacoustics of Turbochargers 8) Shop and Trim Balancing at Two Planes of the Rotor 9) Tribology of the Bearing Surface Roughness 10) Design of Turbocharger Platforms using the Similarity Laws The rotor response of an automotive turbocharger at high rotor speeds is studied analytically, computationally, and experimentally. Due to the nonlinear character...

  19. Current Automotive Holometry Studies

    Science.gov (United States)

    Marchi, Mitchell M.; Snyder, D. S.

    1990-04-01

    Holometry studies of automotive body and powertrain components have become a very useful high resolution test methodology to knowledgeable Ford engineering personnel. Current examples of studies that represent the static or dynamic operational conditions of the automotive test component are presented. Continuous wave laser holometry, computer aided holometry (CAH) and pulsed laser holometry were the holometric techniques used to study the following subjects: (1) body in prime (BIP) vibration modes, (2) transmission flexplate stud-torque converter deformation due to engine torque pulses, (3) engine cylinder head and camshaft support structure deformation due to cylinder pressure and (4) engine connecting rod/cap lift-off. Static and dynamic component loading and laboratory techniques required to produce usable and valid test results are discussed along with possible conclusions for the engineering concerns.

  20. Automotive Industry in Malaysia

    DEFF Research Database (Denmark)

    Wad, Peter; Govindaraju, V.G.R. Chandran

    2011-01-01

    expanded in terms of sales, production, employment and local content, but failed in industrial upgrading and international competitiveness. The failures can be attributed to (a) lack of political promotion for high challenge-high support environment, (b) low technological and marketing capabilities and (c......This paper explains the evolution and assesses the development of the Malaysian automotive industry within the premise of infant industry and trade protection framework as well as extended arguments of infant industry using a global value chain perspective. The Malaysian automotive industry......) limited participation in the global value chain. Although the Malaysian infant industry protection policy comprised many promising initiatives, the national and the overall domestic automobile industry ended up as a captive of the regionalised Japanese keiretsu system in automobile manufacturing. A new...

  1. Automotive systems engineering

    Energy Technology Data Exchange (ETDEWEB)

    Maurer, Markus [Technische Univ. Braunschweig (Germany). Inst. fuer Regelungstechnik; Winner, Hermann (eds.) [Technische Univ. Darmstadt (Germany). Fachgebiet Fahrzeugtechnik

    2013-06-01

    Innovative state-of-the-art book. Presents brand new results of a joint workshop in the field of automotive systems engineering. Recommendable to students for further reading even though not a primary text book. This book reflects the shift in design paradigm in automobile industry. It presents future innovations, often referred as ''automotive systems engineering''. These cause fundamental innovations in the field of driver assistance systems and electro-mobility as well as fundamental changes in the architecture of the vehicles. New driving functionalities can only be realized if the software programs of multiple electronic control units work together correctly. This volume presents the new and innovative methods which are mandatory to master the complexity of the vehicle of the future.

  2. FISITA 2012 World Automotive Congress

    CERN Document Server

    2013-01-01

    Proceedings of the FISITA 2012 World Automotive Congress are selected from nearly 2,000 papers submitted to the 34th FISITA World Automotive Congress, which is held by Society of Automotive Engineers of China (SAE-China ) and the International Federation of Automotive Engineering Societies (FISITA). This proceedings focus on solutions for sustainable mobility in all areas of passenger car, truck and bus transportation. Volume 8: Vehicle Design and Testing (II) focuses on: •Automotive Reliability Technology •Lightweight Design Technology •Design for Recycling •Dynamic Modeling •Simulation and Experimental Validation •Virtual Design, Testing and Validation •Testing of Components, Systems and Full Vehicle Above all researchers, professional engineers and graduates in fields of automotive engineering, mechanical engineering and electronic engineering will benefit from this book.   SAE-China is a national academic organization composed of enterprises and professionals who focus on research, design a...

  3. Automotive Chassis; Automotive Mechanics-Basic: 9043.02.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This automotive chassis course is designed to familiarize the beginning student of the history and development of the automobile with basic concepts common to the automobile industry, and general information that is required for successful advancement in the automotive mechanics field. It is one quinmester in a series of quinmester outlines…

  4. Automotive mechatronics automotive networking, driving stability systems, electronics

    CERN Document Server

    2015-01-01

    As the complexity of automotive vehicles increases this book presents operational and practical issues of automotive mechatronics. It is a comprehensive introduction to controlled automotive systems and provides detailed information of sensors for travel, angle, engine speed, vehicle speed, acceleration, pressure, temperature, flow, gas concentration etc. The measurement principles of the different sensor groups are explained and examples to show the measurement principles applied in different types. Contents Basics of mechatronics.- Architecture.- Electronic control unit.- Software development.- Basic principles of networking.- Automotive networking.- Bus systems.- Automotive sensors.- Sensor measuring principles.- Sensor types.- Electric actuators.- Electrohydraulic actuators.- Electronic transmission control.- Electronic transmission control unit.- Modules for transmission control.- Antilock braking system.- Traction control system.- Electronic stability program.- Automatic brake functions.- Hydraulic modu...

  5. Reliability in automotive ethernet networks

    DEFF Research Database (Denmark)

    Soares, Fabio L.; Campelo, Divanilson R.; Yan, Ying;

    2015-01-01

    This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular.......This paper provides an overview of in-vehicle communication networks and addresses the challenges of providing reliability in automotive Ethernet in particular....

  6. Automotive battery technology

    CERN Document Server

    Watzenig, Daniel

    2014-01-01

    The use of electrochemical energy storage systems in automotive applications also involves new requirements for modeling these systems, especially in terms of model depth and model quality. Currently, mainly simple application-oriented models are used to describe the physical behavior of batteries. This book provides a step beyond of state-of-the-art modeling showing various different approaches covering following aspects: system safety, misuse behavior (crash, thermal runaway), battery state estimation and electrochemical modeling with the needed analysis (pre/post mortem). All this different approaches are developed to support the overall integration process from a multidisciplinary point-of-view and depict their further enhancements to this process.

  7. Automotive systems engineering

    CERN Document Server

    Winner, Hermann

    2013-01-01

    This book reflects the shift in design paradigm in automobile industry. It presents future innovations, often referred as  “automotive systems engineering”.  These cause fundamental innovations in the field of driver assistance systems and electro-mobility as well as fundamental changes in the architecture of the vehicles. New driving functionalities can only be realized if the software programs of multiple electronic control units work together correctly. This volume presents the new and innovative methods which are mandatory to master the complexity of the vehicle of the future.

  8. Ultracapacitors for automotive applications

    Science.gov (United States)

    Ashtiani, Cyrus; Wright, Randy; Hunt, Gary

    In response to a growing consensus in the auto industry that ultracapacitors can potentially play a key role in the modern vehicle power distribution network, a task force was created at the United States Advanced Battery Consortium (USABC) to tackle issues facing the fledging industry. The task force embarked on first developing and establishing standards for performance and abuse tolerance of ultracapacitors in collaboration with the U.S. Department of Energy and National Labs. Subsequently, potential applications in the automotive industry were identified and a consensus requirement specification was drawn as a development guide for the industry.

  9. The automotive transmission book

    CERN Document Server

    Fischer, Robert; Jürgens, Gunter; Najork, Rolf; Pollak, Burkhard

    2015-01-01

    This book presents essential information on systems and interactions in automotive transmission technology and outlines the methodologies used to analyze and develop transmission concepts and designs. Functions of and interactions between components and subassemblies of transmissions are introduced, providing a basis for designing transmission systems and for determining their potentials and properties in vehicle-specific applications: passenger cars, trucks, buses, tractors, and motorcycles. With these fundamentals the presentation provides universal resources for both state-of-the-art and future transmission technologies, including systems for electric and hybrid electric vehicles.

  10. INTEGRATED AUTOMOTIVE MANUFACTURING SUPPLY

    Directory of Open Access Journals (Sweden)

    P.J.S. Van Dyk

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Supply planning and traffic flow planning are major activities in the automotive manufacturing environment worldwide. Traditionally, the impact of supply planning strategies on plant traffic is rarely considered. This paper describes the development of a Decision Support System (DSS that will assist automotive manufacturers to analyse the effect of supply planning decisions on plant traffic during the supply planning phase of their logistics planning process. In essence, this DSS consists of a Supply Medium Decision Support Tool (SMDST (an interactive MS-Excel model with Visual Basic interfacing and a traffic flow simulation model tool (using eMPlant simulation software.

    AFRIKAANSE OPSOMMING: Verskaffingsbeplanning en verkeersvloeibeplanning is belangrike aktiwiteite in die motorvervaardigingsbedryf wêreldwyd. Tradisioneel word die uitwerking van verskaffings-beplanningsstrategië op aanlegverkeer selde in ag geneem. Hierdie artikel beskryf die ontwikkeling van ’n Besluitnemings Ondersteuningstelsel (DSS wat motorvervaardigers sal ondersteun in die analise van die effek van verskaffingsbeplanningbesluite op aanlegverkeer tydens die verskaffingsbeplanningsfase van hulle logistieke beplanningsproses. Hierdie DSS bestaan hoofsaaklik uit ’n Verskaffings-vervoermiddel Besluitnemingshulpmiddel (SMDST (’n interaktiewe MS-Excel model met “Visual Basic” koppelling asook ’n simulasiemodel van verkeersvloei (met eM-Plant simulasiesagteware.

  11. Leaf litter breakdown, microbial respiration and shredder production in metal-polluted streams

    Science.gov (United States)

    Carlisle, D.M.; Clements, W.H.

    2005-01-01

    1. If species disproportionately influence ecosystem functioning and also differ in their sensitivities to environmental conditions, the selective removal of species by anthropogenic stressors may lead to strong effects on ecosystem processes. We evaluated whether these circumstances held for several Colorado, U.S.A. streams stressed by Zn. 2. Benthic invertebrates and chemistry were sampled in five second-third order streams for 1 year. Study streams differed in dissolved metal concentrations, but were otherwise similar in chemical and physical characteristics. Secondary production of leaf-shredding insects was estimated using the increment summation and size-frequency methods. Leaf litter breakdown rates were estimated by retrieving litter-bags over a 171 day period. Microbial activity on leaf litter was measured in the laboratory using changes in oxygen concentration over a 48 h incubation period. 3. Dissolved Zn concentrations varied eightfold among two reference and three polluted streams. Total secondary production of shredders was negatively associated with metal contamination. Secondary production in reference streams was dominated by Taenionema pallidum. Results of previous studies and the current investigation demonstrate that this shredder is highly sensitive to metals in Colorado headwater streams. Leaf litter breakdown rates were similar between reference streams and declined significantly in the polluted streams. Microbial respiration at the most contaminated site was significantly lower than at reference sites. 4. Our results supported the hypothesis that some shredder species contribute disproportionately to leaf litter breakdown. Furthermore, the functionally dominant taxon was also the most sensitive to metal contamination. We conclude that leaf litter breakdown in our study streams lacked functional redundancy and was therefore highly sensitive to contaminant-induced alterations in community structure. We argue for the necessity of simultaneously

  12. SEES project - how to improve the recyclability potential of automotive electronics

    Energy Technology Data Exchange (ETDEWEB)

    Alonso, J.C. [Lear Automotive (EEDS) Spain SL, Valls (Spain); Lichtenvort, K. [Technical Univ. of Berlin, Systems Environmental Engineering, Berlin (Germany); Arnaiz, S. [GAIKER Centro Tecnologico, Zamudio (Spain)

    2004-07-01

    The paper presents the SEES project (Sustainable Electrical and Electronic System for the Automotive Sector) that is being developed under the EU Contract n TST3-CT-2003-506075 inside the Sixth Framework Programme, Priority 6.2. The consortium includes two universities (TU Berlin and Universitat Rovira i Virgili), three industries (FORD, LEAR and Rohm and Haas), two research organisations (GAIKER and CIMA) and four SEMs (Indumetal Recycling, Metall Recycling, Mueller-Guttenbrunn and Salyp). This partnership covers all actors involved in the manufacture and end-of-life steps of product life cycle: suppliers of automotive systems, car manufacturers, car dismantlers, car shredders, metal recyclers and plastic recyclers. The life cycle steps will be analysed using LCA and LCC methodologies to define the most sustainable scenario for the Electrical and Electronic System (EES) of the car from economic and environmental points of view. Aspects considered are the optimisation of the assembly during manufacture and the dismantling, recycling and shredding processes during end-of-life. Further innovation are design guidelines; use of innovative materials; prototyping, testing of illustrative samples and development of methodologies/software tools to support recyclers and designers decisions. (orig.)

  13. Tank-automotive robotics

    Science.gov (United States)

    Lane, Gerald R.

    1999-07-01

    To provide an overview of Tank-Automotive Robotics. The briefing will contain program overviews & inter-relationships and technology challenges of TARDEC managed unmanned and robotic ground vehicle programs. Specific emphasis will focus on technology developments/approaches to achieve semi- autonomous operation and inherent chassis mobility features. Programs to be discussed include: DemoIII Experimental Unmanned Vehicle (XUV), Tactical Mobile Robotics (TMR), Intelligent Mobility, Commanders Driver Testbed, Collision Avoidance, International Ground Robotics Competition (ICGRC). Specifically, the paper will discuss unique exterior/outdoor challenges facing the IGRC competing teams and the synergy created between the IGRC and ongoing DoD semi-autonomous Unmanned Ground Vehicle and DoT Intelligent Transportation System programs. Sensor and chassis approaches to meet the IGRC challenges and obstacles will be shown and discussed. Shortfalls in performance to meet the IGRC challenges will be identified.

  14. Incineration as a treatment option for shredder light fractions (SLF) by a stationary fluidised bed combustion; Untersuchungen zur Verbrennung von Shredderleichtfraktionen in einer stationaeren Wirbelschicht

    Energy Technology Data Exchange (ETDEWEB)

    Hofmann, Gaston

    2011-07-15

    In this paper the suitability of the stationary fluidised bed combustion as a treatment option for shredder light fractions (SLF) is discussed. This SLF, SLF coarse grain and SLF generated in a further mechanical treatment were burned. The results show a strong change in grain size distribution of the bed material during the combustion the SLF and SLF-coarse fractions. The formation of agglomerates significantly impaired the fluidization. The main reason for this effect is the high content of alkali and alkaline earth metals in the SLF. During the incineration of SLF generated by further mechanical treatment the change in grain size distribution declines much more slowly. This results from the separation of hard plastics with higher calcium contents during further mechanical processing. The tests also showed a complete burnout and a significant enrichment of metals in the solid combustion residues (fabric filter ash bed ash, cyclone ash). These residues represent a recycling concentrate, which needs to be open in the future. (orig.)

  15. Leaf Barriers to Fungal Colonization and Shredders (Tipula lateralis) Consumption of Decomposing Eucalyptus globulus.

    Science.gov (United States)

    Canhoto; Graça

    1999-04-01

    > Abstract Herein we assess the importance of leaf cuticle, polyphenolic, and essential oils contents of Eucalyptus globulus leaves to hyphomycete colonization and shredder consumption. Optical and electron microscopy revealed that, at least during the first 5 weeks of conditioning, the cuticle remains virtually intact. Stomata provide the main access for hyphae to internal leaf tissues and, eventually, for spore release. We suggest that in E. globulus leaves, fungal decomposition progresses predominantly in and from the eucalyptus leaf mesophyll to the outside. Malt extract agar media supplemented with either eucalyptus essential oils or tannic acid completely inhibited (Articulospora tetracladia, Lemonniera aquatica, and Tricladium gracile) or depressed (Heliscus lugdunensis, Lunulospora curvula, and Tricladium angulatum) aquatic hyphomycetes growth. The transference of both secondary compounds to alder leaves induced similar and significant reduction in Tipula lateralis larval consumption. Results consistently indicate that eucalyptus oils are stronger deterrents than polyphenols. The waxy cuticle of E. globulus appears to be a key physical factor delaying fungal colonization during decomposition. We hypothesize that the relative influence of leaf phenols and essential oils to aquatic hyphomycetes and shredders may be related to three main factors: (a) initial distribution of such compounds in the leaves; (b) possibility of their decrease through decomposition; and (c) consumption strategies of detritivores.

  16. Waterborne toxicity and diet-related effects of fungicides in the key leaf shredder Gammarus fossarum (Crustacea: Amphipoda).

    Science.gov (United States)

    Zubrod, J P; Englert, D; Wolfram, J; Wallace, D; Schnetzer, N; Baudy, P; Konschak, M; Schulz, R; Bundschuh, M

    2015-12-01

    Animals involved in leaf litter breakdown (i.e., shredders) play a central role in detritus-based stream food webs, while their fitness and functioning can be impaired by anthropogenic stressors. Particularly fungicides can affect shredders via both waterborne exposure and their diet, namely due to co-ingestion of adsorbed fungicides and shifts in the leaf-associated fungal community, on which shredders' nutrition heavily relies. To understand the relevance of these effect pathways, we used a full 2×2-factorial test design: the leaf material serving as food was microbially colonized for 12 days either in a fungicide-free control or exposed to a mixture of five current-use fungicides (sum concentration of 62.5μg/L). Similarly, the amphipod shredder Gammarus fossarum was subjected to the same treatments but for 24 days. Waterborne exposure reduced leaf consumption by ∼20%, which did not fully explain the reduction in feces production (∼30%), indicating an enhanced utilization of food to compensate for detoxification mechanisms. This may also explain the reduced feces production (∼10%) of gammarids feeding on fungicide-exposed leaves. The reduction may, however, also be caused by a decreased nutritious quality of the leaves indicated by a reduced species richness (∼40%) of leaf-associated fungi. However, compensation for these effects by Gammarus was seemingly incomplete, since both waterborne exposure and the consumption of the fungicide-affected diet drastically reduced gammarid growth (∼110% and ∼40%, respectively). Our results thus indicate that fungicide mixtures have the potential for detrimental implications in aquatic ecosystem functioning by affecting shredders via both effect pathways.

  17. MEMS for automotive and aerospace applications

    CERN Document Server

    Kraft, Michael

    2013-01-01

    MEMS for automotive and aerospace applications reviews the use of Micro-Electro-Mechanical-Systems (MEMS) in developing solutions to the unique challenges presented by the automotive and aerospace industries.Part one explores MEMS for a variety of automotive applications. The role of MEMS in passenger safety and comfort, sensors for automotive vehicle stability control applications and automotive tire pressure monitoring systems are considered, along with pressure and flow sensors for engine management, and RF MEMS for automotive radar sensors. Part two then goes on to explore MEMS for

  18. Automotive powerplant evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Stamper, K.R.

    1976-06-01

    A program to obtain automotive engine performance data for use in estimating vehicle emission and fuel economy in varied service and duty is described. An experimental test procedure for generating fuel consumption and emissions data adequate to characterize an engine over its full operating range was developed for steady-state tests. The development of a test procedure for transient testing is currently under way. The steady-state data will be collected from approximately 23 different engines, including: (1) 16 current production spark-ignition engines; (2) 3 pre-production or prototype advanced design spark-ignition engines; and (3) 4 light-duty diesel engines which are, or could be, used in passenger car applications. To date, steady-state ''engine maps'' were completed on 10 engines. A simplified model used to compare steady-state data with chassis dynamometer data indicates that results thus far can be used to obtain estimates of fuel economy in automobiles.

  19. Spectroscopic analysis of automotive engine oil

    Science.gov (United States)

    Dahmani, Rachid; Gupta, Neelam

    2002-02-01

    Infrared absorption spectroscopy (IR) and acousto-optic tunable filter (AOTF) technology were combined to develop a portable spectrophotometer for use in engine oil analysis to identify and quantify oil contaminants and residue products, Preliminary measurements were taken with a field-portable AOTF-based spectrometer (2 to 4.5 micrometers ) and an FTIR spectrometer (2 to 25 micrometers ) for comparison. Absorption spectra of used and unused oil samples were measured and compared to determine absorption changes between the various samples resulting from oil degradation and any chemical reactions that might have taken place during high- temperature engine lubrication. These preliminary results indicate that IR spectroscopy can be used for oil quality monitoring in automotive engines, which will help predict and prevent engine failure and degradation. This work can be extended to other remote sensing applications, such as the monitoring of environmental oil spills.

  20. Determining organic pollutants in automotive industry sludge.

    Science.gov (United States)

    Munaretto, Juliana S; Wonghon, Audrey L; von Mühlen, Carin

    2012-12-01

    In Brazil, the policy for disposing industrial sludge is changing from an emphasis on using controlled landfills to other treatment or co-processing methods; however, the monitoring of organic pollutants is not mandatory. The present study evaluated two general screening methods for organic pollutants in sludge generated in an automotive industrial complex in southern Brazil. The screening was performed using Soxhlet and sonication extractions and Gas Chromatograph coupled with Quadrupole Mass Spectrometry (GC/qMS). It was concluded that both techniques were effective and that most of the compounds identified were alkanes, phenols and esters. Important pollutants were detected in the sludge, which confirms the necessity of monitoring this type of residue.

  1. Escalation Practices in Automotive Development

    Directory of Open Access Journals (Sweden)

    Tomaž Jurejevčič

    2016-12-01

    Full Text Available Research Question (RQ: In automotive business many risk-involved situations occur and when detected, an escalation process takes place. Although defined and controlled by process guidelines and being supported by experts, escalation brings increased emotional pressure and stress for parties involved. Do escalation processes in automotive industry maintain all implied challenges? Purpose: The purpose of the article is to present current status of escalation processes and gaps between theory and practice cases. Results of the analysis are recommendations of good engineering practice derived also from actual experiences and learned lessons. Method: The method involves analysis of practical cases from automotive development process, lessons learned, anonymous survey of automotive engineers and classification of experiences. Results: Results of the survey have shown that the controlled escalation process for know-how related escalations is needed in order to establish the environment where the team is able to provide new, sometimes unconventional ideas for the problem to be solved. Organization: Presented recommendations and measures enable organization and managers to put the expertise and experiences of employees into action for problem solving during escalation. Originality: In this article some practices are presented that, although simple and some yet seen, with proper adjustment stemming from real life processes give a fruitful settlement of escalations in automotive development business.

  2. Importance of Projects in Automotive Industry

    Science.gov (United States)

    Babeľová, Zdenka Gyurák; Lenhardtová, Zuzana; Cagáňová, Dagmar; Weidlichová-Luptáková, Stanislava

    2010-01-01

    For automotive companies, research and development is the key to success for new generation of products. The aim of this article is to accent the importance of innovations and innovations-focused projects in automotive industry. Relevance of co-operation between automotive industry and educational institutions is noticed in the article, too. Furthermore, history of automotive industry in Slovakia is outlined in the article. Main part of the article is focused on project AUTOCLUSTERS.

  3. Consequences of warming and resource quality on the stoichiometry and nutrient cycling of a stream shredder.

    Science.gov (United States)

    Mas-Martí, Esther; Romaní, Anna M; Muñoz, Isabel

    2015-01-01

    As a result of climate change, streams are warming and their runoff has been decreasing in most temperate areas. These changes can affect consumers directly by increasing their metabolic rates and modifying their physiology and indirectly by changing the quality of the resources on which organisms depend. In this study, a common stream detritivore (Echinogammarus berilloni Catta) was reared at two temperatures (15 and 20°C) and fed Populus nigra L. leaves that had been conditioned either in an intermittent or permanent reach to evaluate the effects of resource quality and increased temperatures on detritivore performance, stoichiometry and nutrient cycling. The lower quality (i.e., lower protein, soluble carbohydrates and higher C:P and N:P ratios) of leaves conditioned in pools resulted in compensatory feeding and lower nutrient retention capacity by E. berilloni. This effect was especially marked for phosphorus, which was unexpected based on predictions of ecological stoichiometry. When individuals were fed pool-conditioned leaves at warmer temperatures, their growth rates were higher, but consumers exhibited less efficient assimilation and higher mortality. Furthermore, the shifts to lower C:P ratios and higher lipid concentrations in shredder body tissues suggest that structural molecules such as phospholipids are preserved over other energetic C-rich macromolecules such as carbohydrates. These effects on consumer physiology and metabolism were further translated into feces and excreta nutrient ratios. Overall, our results show that the effects of reduced leaf quality on detritivore nutrient retention were more severe at higher temperatures because the shredders were not able to offset their increased metabolism with increased consumption or more efficient digestion when fed pool-conditioned leaves. Consequently, the synergistic effects of impaired food quality and increased temperatures might not only affect the physiology and survival of detritivores but

  4. Consequences of warming and resource quality on the stoichiometry and nutrient cycling of a stream shredder.

    Directory of Open Access Journals (Sweden)

    Esther Mas-Martí

    Full Text Available As a result of climate change, streams are warming and their runoff has been decreasing in most temperate areas. These changes can affect consumers directly by increasing their metabolic rates and modifying their physiology and indirectly by changing the quality of the resources on which organisms depend. In this study, a common stream detritivore (Echinogammarus berilloni Catta was reared at two temperatures (15 and 20°C and fed Populus nigra L. leaves that had been conditioned either in an intermittent or permanent reach to evaluate the effects of resource quality and increased temperatures on detritivore performance, stoichiometry and nutrient cycling. The lower quality (i.e., lower protein, soluble carbohydrates and higher C:P and N:P ratios of leaves conditioned in pools resulted in compensatory feeding and lower nutrient retention capacity by E. berilloni. This effect was especially marked for phosphorus, which was unexpected based on predictions of ecological stoichiometry. When individuals were fed pool-conditioned leaves at warmer temperatures, their growth rates were higher, but consumers exhibited less efficient assimilation and higher mortality. Furthermore, the shifts to lower C:P ratios and higher lipid concentrations in shredder body tissues suggest that structural molecules such as phospholipids are preserved over other energetic C-rich macromolecules such as carbohydrates. These effects on consumer physiology and metabolism were further translated into feces and excreta nutrient ratios. Overall, our results show that the effects of reduced leaf quality on detritivore nutrient retention were more severe at higher temperatures because the shredders were not able to offset their increased metabolism with increased consumption or more efficient digestion when fed pool-conditioned leaves. Consequently, the synergistic effects of impaired food quality and increased temperatures might not only affect the physiology and survival of

  5. Value analysis of neodymium content in shredder feed: toward enabling the feasibility of rare earth magnet recycling.

    Science.gov (United States)

    Bandara, H M Dhammika; Darcy, Julia W; Apelian, Diran; Emmert, Marion H

    2014-06-17

    In order to facilitate the development of recycling technologies for rare earth magnets from postconsumer products, we present herein an analysis of the neodymium (Nd) content in shredder scrap. This waste stream has been chosen on the basis of current business practices for the recycling of steel, aluminum, and copper from cars and household appliances, which contain significant amounts of rare earth magnets. Using approximations based on literature data, we have calculated the average Nd content in the ferrous shredder product stream to be between 0.13 and 0.29 kg per ton of ferrous scrap. A value analysis considering rare earth metal prices between 2002 and 2013 provides values between $1.32 and $145 per ton of ferrous scrap for this material, if recoverable as pure Nd metal. Furthermore, we present an analysis of the content and value of other rare earths (Pr, Dy, Tb).

  6. Antenna Arrays and Automotive Applications

    CERN Document Server

    Rabinovich, Victor

    2013-01-01

    This book throws a lifeline to designers wading through mounds of antenna array patents looking for the most suitable systems for their projects. Drastically reducing the research time required to locate solutions to the latest challenges in automotive communications, it sorts and systematizes material on cutting-edge antenna arrays that feature multi-element communication systems with enormous potential for the automotive industry. These new systems promise to make driving safer and more efficient, opening up myriad applications, including vehicle-to-vehicle traffic that prevents collisions, automatic toll collection, vehicle location and fine-tuning for cruise control systems. This book’s exhaustive coverage begins with currently deployed systems, frequency ranges and key parameters. It proceeds to examine system geometry, analog and digital beam steering technology (including "smart" beams formed in noisy environments), maximizing signal-to-noise ratios, miniaturization, and base station technology that ...

  7. GLOBAL PERSPECTIVES IN AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    NICOLETA ISAC

    2010-01-01

    Full Text Available The automotive sector is characterised by a relatively low trade/salesratio. While the production of most automotive producers in the world is spread over variouscountries in the value chain, the brands are still considered to reflect some national identity.Internationalisation strategies may change over the lifecycle of the product and automakerstend to pursue diametrically opposed strategies. In mature markets, it is about managing whatgoes on beneath a static surface; in emerging markets’ dynamic environments, companies muststrategically position themselves to benefit from growth opportunities. However, without theright strategy and execution in mature markets, it is clear that traditional OEMs cannot profitfrom emerging markets-the persistence of structural issues in mature market operationseventually will rob all but the most resilient competitors of the opportunity to compete inemerging markets.

  8. Rejuvenation of automotive fuel cells

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yu Seung; Langlois, David A.

    2016-08-23

    A process for rejuvenating fuel cells has been demonstrated to improve the performance of polymer exchange membrane fuel cells with platinum/ionomer electrodes. The process involves dehydrating a fuel cell and exposing at least the cathode of the fuel cell to dry gas (nitrogen, for example) at a temperature higher than the operating temperature of the fuel cell. The process may be used to prolong the operating lifetime of an automotive fuel cell.

  9. On Ugliness and the Automotive

    DEFF Research Database (Denmark)

    Herriott, Richard

    2016-01-01

    The function of this essay is to to see what consequences a consideration of ugliness in automotive styling has for the theories of three writers on aesthetics in design: David Pye, Roger Scruton and Ralf Weber. As such, the concepts of beauty and ugliness will be treated in brief before moving...... on to look at an outline of the three aesthetic theories in relation to car design....

  10. Do climate and soil influence phenotypic variability in leaf litter, microbial decomposition and shredder consumption?

    Science.gov (United States)

    Graça, M A S; Poquet, J M

    2014-03-01

    We tested the hypothesis that water stress and soil nutrient availability drive leaf-litter quality for decomposers and detritivores by relating chemical and physical leaf-litter properties and decomposability of Alnus glutinosa and Quercus robur, sampled together with edaphic parameters, across wide European climatic gradients. By regressing principal components analysis of leaf traits [N, P, condensed tannins, lignin, specific leaf area (SLA)] against environmental and soil parameters, we found that: (1) In Q. robur the condensed tannin and lignin contents increased and SLA decreased with precipitation, annual range of temperature, and soil N content, whereas leaf P increased with soil P and temperature; (2) In A. glutinosa leaves N, P, and SLA decreased and condensed tannins increased with temperature, annual range of temperature, and decreasing soil P. On the other hand, leaf P and condensed tannins increased and SLA decreased with minimum annual precipitation and towards sites with low temperature. We selected contrasting leaves in terms of quality to test decomposition and invertebrate consumption. There were intraspecific differences in microbial decomposition rates (field, Q. robur) and consumption by shredders (laboratory, A. glutinosa). We conclude that decomposition rates across ecosystems could be partially governed by climate and soil properties, affecting litter quality and therefore decomposers and detritivores. Under scenarios of global warming and increased nutrients, these results suggest we can expect species-specific changes in leaf-litter properties most likely resulting in slow decomposition with increased variance in temperatures and accelerated decomposition with P increase.

  11. International Congress of Automotive and Transport Engineering

    CERN Document Server

    Ispas, Nicolae

    2017-01-01

    The volume will include selected and reviewed papers from CONAT - International Congress of Automotive and Transport Engineering to be held in Brasov, Romania, in October 2016. Authors are experts from research, industry and universities coming from 14 countries worldwide. The papers are covering the latest developments in automotive vehicles and environment, advanced transport systems and road traffic, heavy and special vehicles, new materials, manufacturing technologies and logistics, accident research and analysis and innovative solutions for automotive vehicles. The conference will be organized by SIAR (Society of Automotive Engineers from Romania) in cooperation with FISITA. .

  12. Long-term effects of fungicides on leaf-associated microorganisms and shredder populations-an artificial stream study.

    Science.gov (United States)

    Zubrod, Jochen P; Englert, Dominic; Wolfram, Jakob; Rosenfeldt, Ricki R; Feckler, Alexander; Bundschuh, Rebecca; Seitz, Frank; Konschak, Marco; Baudy, Patrick; Lüderwald, Simon; Fink, Patrick; Lorke, Andreas; Schulz, Ralf; Bundschuh, Mirco

    2017-02-04

    Leaf litter is a major source of carbon and energy for stream food webs, while both leaf-decomposing microorganisms and macroinvertebrate leaf shredders can be affected by fungicides. Despite the potential for season-long fungicide exposure for these organisms, however, such chronic exposures have not yet been considered. Using an artificial stream facility, effects of a chronic (lasting up to 8 wk) exposure to a mixture of 5 fungicides (sum concentration 20 μg/L) on leaf-associated microorganisms and the key leaf shredder Gammarus fossarum were therefore assessed. While bacterial density and microorganism-mediated leaf decomposition remained unaltered, fungicide exposure reduced fungal biomass (≤71%) on leaves from day 28 onward. Gammarids responded to the combined stress from consumption of fungicide-affected leaves and waterborne exposure with a reduced abundance (≤18%), which triggered reductions in final population biomass (18%) and in the number of precopula pairs (≤22%) but could not fully explain the decreased leaf consumption (19%), lipid content (≤43%; going along with an altered composition of fatty acids), and juvenile production (35%). In contrast, fine particulate organic matter production and stream respiration were unaffected. Our results imply that long-term exposure of leaf-associated fungi and shredders toward fungicides may result in detrimental implications in stream food webs and impairments of detrital material fluxes. These findings render it important to understand decomposer communities' long-term adaptational capabilities to ensure that functional integrity is safeguarded. Environ Toxicol Chem 2017;9999:1-12. © 2017 SETAC.

  13. Petroleum Marketing. Selling Automotive Products and Services.

    Science.gov (United States)

    Luter, Robert R.

    This textbook contains material for the individualized instruction of students training for careers in service stations; automotive, tire, battery, and accessory retail stores; oil jobbers and petroleum product wholesalers, or any wholesale or retail establishment that sells automotive products and services. Included among the topics addressed in…

  14. Automotive Thermoelectric Waste Heat Recovery

    Science.gov (United States)

    Meisner, Gregory P.

    2015-03-01

    Considerable fuel energy, as much as 70%, is not converted to useful work by internal combustion engines but is instead rejected as waste heat, and more than half of the waste heat, nearly 40% of fuel energy, is contained in vehicle exhaust gas. This provides an opportunity to recover some of the wasted fuel energy and convert it from heat into useful work, subject to the laws of thermodynamics, and thereby improve vehicle energy efficiency. Thermoelectric (TE) materials have been extensively researched and TE devices are now being developed for operation at high temperatures corresponding to automotive exhaust gases for direct solid-state conversion of heat into electricity. This has stimulated substantial progress in the development of practical TE generator (TEG) systems for large-scale commercialization. A significant enabler of this progress has been the US Department of Energy's Vehicle Technologies Program through funding for low cost solutions for automotive TE waste heat recovery to improve fuel economy. Our current project at General Motors has culminated in the identification of the potential supply chain for all components and assembly of an automotive TEG. A significant focus has been to develop integrated and iterative modeling tools for a fully optimized TEG design that includes all components and subsystems (TE modules, heat exchangers, thermal interfaces, electrical interconnects, power conditioning, and vehicle integration for maximal use of TEG power). We have built and tested a new, low-cost Initial TEG prototype based on state-of-the-art production-scale skutterudite TE modules, novel heat exchanger designs, and practical solutions to the many technical challenges for optimum TEG performance. We will use the results for our Initial TEG prototype to refine our modeling and design tools for a Final automotive TEG system prototype. Our recent results will be presented. Thanks to: J.R. Salvador, E.R. Gundlach, D. Thompson, N.K. Bucknor, M

  15. Predation Risk versus Pesticide Exposure: Consequences of Fear and Loathing in the Life of Stream Shredders

    Science.gov (United States)

    Pestana, J. T.; Baird, D. J.; Soares, A. M.

    2005-05-01

    Stream invertebrates are exposed to complex stressor regimes including both biotic and abiotic factors. Species living in streams in agricultural landscapes are often subjected to episodic or continuous exposures to low levels of agrochemicals, which may approach or exceed specific substance guidelines. Sublethal effects of pesticides may result in direct effects on organisms (e.g. reduced physiological performance), which may in turn contribute to indirect effects relating to survival (e.g. increased predation risk). Here, we investigate the possibility that predator-release kairomones can act additively with low-level pesticide exposure to reduce physiological performance and survival of stream invertebrates in previously unforeseen ways. Feeding, metabolic and behavioural responses of two shredder insects, the North American stonefly Pteronarcys comstockii and the European caddisfly Sericostoma vittatum were measured under exposure to the insecticide imidacloprid at different levels of indirect predation stress using predator-release kairomones from Brown Trout (Salmo trutta). Pteronarcys feeding was measured in terms of mass of naturally conditioned alder leaf discs consumed over a 6-day and 10 -day period in animals held in cages in stream mesocosms. Pteronarcys feeding was impaired at 1 ppb in the 6-day trial and at 0,5 ppb in the 10-day trial relatively to unexposed controls. Metabolic rate was measured in the lab in terms of oxygen consumption of Pteronarcys. Animals exposed to 0.5 and 1 ppb imidacloprid showed elevated respiratory rates compared to controls. Laboratory experiments with Sericostoma, currently in progress, are examining the separate and combined effects of imidacloprid and predator kairomone on similar endpoints. These preliminary results are discussed in relation to the development of the Mechanistic Unifying Stressor Effects (MUSE) model which can be used to predict combined ecological effects of multiple stressors at the population level.

  16. Enzymatic biomarkers can portray nanoCuO-induced oxidative and neuronal stress in freshwater shredders.

    Science.gov (United States)

    Pradhan, Arunava; Silva, Carla O; Silva, Carlos; Pascoal, Cláudia; Cássio, Fernanda

    2016-11-01

    Commercial applications of nanometal oxides have increased concern about their release into natural waters and consequent risks to aquatic biota and the processes they drive. In forest streams, the invertebrate shredder Allogamus ligonifer plays a key role in detritus food webs by transferring carbon and energy from plant litter to higher trophic levels. We assessed the response profiles of oxidative and neuronal stress enzymatic biomarkers in A. ligonifer after 96h exposure to nanoCuO at concentration ranges

  17. DISCARD OF THE PLASTIC BOTTLES AND DETERMINATION OF AUTOMOTIVE LUBRICANT OIL RESIDUES IN RIO CLARO-SP = DESCARTE DE EMBALAGENS E QUANTIFICAÇÃO DO VOLUME DE ÓLEO LUBRIFICANTE RESIDUAL NO MUNICÍPIO DE RIO CLARO-SP

    Directory of Open Access Journals (Sweden)

    Edério Dino Bidóia

    2008-01-01

    Full Text Available Concerns about environment conservation have grown in recent years, mainly in industrialized countries, due to growing awareness in these societies regarding the importance of environment quality as the basis for the preservation of future generations. Thus, rather than viewing the environment as a good to be consumed by the productive sector, it is seen as world heritage of humanity. Although lubricant oil represents a small percentage of the waste generated by humans, its impact is very great. One ton of lubricant oil dumped into water systems is equivalent to the pollution caused by 40,000 inhabitants. Thus, only one liter of oil is able to consume the oxygen of a million liters of water, forming, in few days, a fine layer on the surface of 1000 m2 which blocks the passage of air and light for the aquatic organisms. In this context, a study was carried out to collect empty plastic automotive lubricant oil bottles at various gasoline stations in Rio Claro-SP to verify the final destination and determine the volume of lubricant remaining in the bottles. = As preocupações com a conservação do meio ambiente têm crescido nos últimos anos, principalmente em países industrializados, devido à consciência que tem sido construída nessas sociedades sobre a importância da qualidade ambiental como base para a preservação da vida das futuras gerações. A sua carga poluidora é equivalente a 40.000 habitantes por tonelada de óleo despejada em corpos d’água. Apenas um litro de óleo é capaz de esgotar o oxigênio de um milhão de litros de água, formando, em poucos dias, uma fina camada sobre a superfície de 1.000 m2, o que bloqueia a passagem de ar e luz, impedindo a respiração e a fotossíntese. Neste contexto, foi realizada uma pesquisa nos centros de lubrificação e postos de combustíveis do município de Rio Claro-SP para verificar o destino final das embalagens já utilizadas, teoricamente vazias, e também houve coleta destas

  18. Deformation and fatigue behaviors of carburized automotive gear steel and predictions

    Directory of Open Access Journals (Sweden)

    Bonglae Jo

    2016-07-01

    Full Text Available The fatigue behavior of carburized components such as automotive transmission gears is very complex due to hardness and microstructure difference, residual stresses and multi-axial stress states developed between the case and the core. In addition, automotive gears in service, commonly used in helical type, are actually subjected to complex stress conditions such as bending, torsion, and contact stress states. This study presents experimental and analytical results on deformation behavior of carburized steels, widely used in automotive gears, under cyclic stress conditions including axial and torsion loadings. Axial fatigue tests and rotating bending fatigue tests are also included. Predictions of cyclic deformation and fatigue behaviors of the carburized steel with two-layer model are compared with experimental results. The carburized steel investigated in this study exhibited cyclic softening under both axial loading and torsional loading. Predicted results with simple two-layer model for the cyclic deformation and fatigue behaviors were comparatively similar to the experimental data.

  19. Automotive Battery Modelling and Management

    Directory of Open Access Journals (Sweden)

    N. M. Hammad

    2014-06-01

    Full Text Available The estimation of vehicle battery performance is typically addressed by testing the battery under specific operation conditions by using a model to represent the test results. Approaches for representing test results range from simple statistical models to neural networks to complex, physics-based models. Basing the model on test data could be problematical when testing becomes impractical with many years life time tests. So, real time estimation of battery performance, an important problem in automotive applications, falls into this area. In vehicles it is important to know the state of charge of the batteries in order to prevent vehicle stranding and to ensure that the full range of the vehicle operation is exploited. In this paper, several battery models have studied including analytical, electrical circuits, stochastic and electro- chemical models. Valve Regulated Lead Acid “VRLA” battery has been modelled using electric circuit technique. This model is considered in the proposed Battery Monitoring System “BMS”. The proposed BMS includes data acquisition, data analysis and prediction of battery performance under a hypothetical future loads. Based on these criteria, a microprocessor based BMS prototype had been built and tested in automotive Lab,. The tests show promising results that can be used in industrial applications

  20. Development process of automotive microsensors

    Science.gov (United States)

    Tang, William C.

    1995-05-01

    The phased product development approach can be applied advantageously to develop and manufacture automotive microsensors. The phased approach involves a multifunctional team from innovation to development to eventual production and maintenance phases. The key advantage of this approach is the shortened development cycle and fast product introduction, while minimizing waste of resources and lowering risk of product failure. When applied to the product cycles of automotive sensors based on micromachining technology, this approach elucidates several critical considerations. In particular, since industrial application of micromachining technology is still at the infant stage, standards and design rules are not firmly established. Therefore, several important activities must be initiated simultaneously from the start of the innovation phase, which proves to be crucial to the prudent decision of technology alternatives and sensor system configuration. The use of a multifunctional team, as mandated in the phased approach, enables coherent development and optimization of the sense element, the fabrication technology, the packaging approach, the interface circuit configuration, and design features that allow efficient test and assembly flow. Also, with intermediate milestones within each phase, risk assessment and necessary midcourse adjustment to technology trade- offs can be both timely and accurate. Accelerometers, one of the most developed micromachined sensors, serve as representative examples that illustrate how the phased approach can benefits the commercialization of the newly established and rapidly expanding field of micromechanics.

  1. Abundance, population structure and production of macro-invertebrate shredders in a Mediterranean brackish lagoon, Lake Ichkeul, Tunisia

    Science.gov (United States)

    Casagranda, Caterina; Dridi, Mohamed Sadok; Boudouresque, Charles François

    2006-02-01

    Abundance, population structure and production of the macro-invertebrates belonging to the functional feeding group of the shredders were studied in the Ichkeul wetland, northern Tunisia, from July 1993 to April 1994. Mean above-ground macrophyte biomass was at a maximum in September followed by a complete breakdown of the Potamogeton pectinatus L. meadow from October onward due to high salinity following an exceptionally dry winter. Only the meadow of Ruppia cirrhosa (Petagna) Grande at Tinja remained in place. Abundance of Gammarus aequicauda (Martynov 1931), Idotea chelipes (Pallas 1766) and Sphaeroma hookeri Leach 1814 was significantly related to the R. cirrhosa biomass. Gammarus aequicauda presented two recruitment periods in spring and autumn, and S. hookeri a third one in winter. The population of I. chelipes was renewed during winter by continued reproduction without any spring generation. Recruitment of all three species was not very successful during the study period. Life span of all three species was between 12 and 15 months. Despite their relatively low biomass and production rate, the shredders have a key function in processing macrophyte matter to different trophic levels through fragmentation and accelerating the decomposition of macrophyte biomass accumulated at the end of the growth season in the Ichkeul lagoon.

  2. 树枝枝丫粉碎机的研制%Research and Development of Branch Chipper Shredders

    Institute of Scientific and Technical Information of China (English)

    姜雪松; 张红丽

    2012-01-01

    The structure and transmission system of a branch chipper shredder were designed according to the working principles of impact crushers and branch chipper shredders. This equipment consists of automatic feeding mechanism, cutting mechanism, impact crusher mechanism, hammer mill mechanism, and discharge mechanism. It has the following advantages such as high grinding efficiency, safety and reliability.%运用盘式切碎加锤片粉碎的基本工作原理,结合反击破碎原理,对树枝枝丫粉碎机的结构和传动系统进行了设计.该设备主要由自动进料机构、滚筒式切断机构、二级反击破碎机构、锤片粉碎机构和排料机构五部分组成,具有进料辊间距可调、粉碎效率高、安全可靠等特点.

  3. Prospects for MEMS in the Automotive Industry

    Directory of Open Access Journals (Sweden)

    Richard DIXON

    2007-12-01

    Full Text Available An automotive sector as a growth market for MEMS sensors is analyzed in the article. The automotive sector accounted for $1.6 billion, making this the second biggest opportunity after IT peripherals and inkjet print heads. By 2011 the market will top $2.2 billion, a CAGR of around 7%. The main applications in revenues terms are, in order, pressure sensors, gyroscopes, accelerometers and flow sensors and this will remain so for the foreseeable future. Automotive companies are forced to innovate as a result of competition and price pressures.

  4. Automotive Stirling engine development program

    Science.gov (United States)

    Ernst, W.; Richey, A.; Farrell, R.; Riecke, G.; Smith, G.; Howarth, R.; Cronin, M.; Simetkosky, M.; Meacher, J.

    1986-01-01

    This is the ninth Semiannual Technical Progress Report prepared under the Automotive Stirling Engine Development Program. It covers the twenty-eighth and twenty-ninth quarters of activity after award of the contract. Quarterly Technical Progress Reports related program activities from the first through the thirteenth quarters; thereafter, reporting was changed to a Semiannual format. This report summarizes the study of higher-power kinematic Stirling engines for transportation use, development testing of Mod I Stirling engines, and component development activities. Component development testing included successful conical fuel nozzle testing and functional checkout of Mod II controls and auxiliaries on Mod I engine test beds. Overall program philosophy is outlined and data and test results are presented.

  5. INFLUENCE OF AUTOMOTIVE CLUSTERS IN REGIONAL DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Constantin BORDEI

    2014-11-01

    Full Text Available This paper proposes an overview of the evolution in the automotive sector in the process of regional development. The fundamental changes made by the component supplier sector improved the regional development and manufacturing process. Automotive industry is one of the modern sectors in many countries that benefits of a high technology impact and creates jobs that reduces unemployment across Europe. The auto industry changed cities, regions and countries into poles of development and it becomes more and more efficient. The high foreign direct investments from the automotive sector play an important role in regional development process. Continuous changes are being made in the economy, society, and company; in conclusion the automotive clusters will always be a subject of analysis.

  6. Fatal exit the automotive black box debate

    CERN Document Server

    Kowalick, Tom

    2005-01-01

    "Fatal Exit: The Automotive Black Box Debate cuts through thirty years of political wrangling and institutional biases to provide an argument for the Motor Vehicle Event Data Recorder (MVEDR). This automotive equivalent of an airplane's flight recorder or black box is intended to solve the mysteries of car crashes and improve the safety of our roads. The reader is taken inside the automotive industry and the government highway safety establishment to foster an understanding of the politics and the positions on all sides of this safety debate. The author takes an unbiased approach, chronologically presenting each argument and uncovering the agendas and mandates of each of the stakeholders." "This publication is essential reading for all consumers who need to have their voices heard on this critical issue, as well as for attorneys, public safety advocates, public policy administrators, engineers, automotive professionals, journalists, and insurance executives."--Jacket.

  7. Nonlinear estimation and control of automotive drivetrains

    CERN Document Server

    Chen, Hong

    2014-01-01

    Nonlinear Estimation and Control of Automotive Drivetrains discusses the control problems involved in automotive drivetrains, particularly in hydraulic Automatic Transmission (AT), Dual Clutch Transmission (DCT) and Automated Manual Transmission (AMT). Challenging estimation and control problems, such as driveline torque estimation and gear shift control, are addressed by applying the latest nonlinear control theories, including constructive nonlinear control (Backstepping, Input-to-State Stable) and Model Predictive Control (MPC). The estimation and control performance is improved while the calibration effort is reduced significantly. The book presents many detailed examples of design processes and thus enables the readers to understand how to successfully combine purely theoretical methodologies with actual applications in vehicles. The book is intended for researchers, PhD students, control engineers and automotive engineers. Hong Chen is a professor at the State Key Laboratory of Automotive Simulation and...

  8. INFLUENCE OF AUTOMOTIVE CLUSTERS IN REGIONAL DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Constantin BORDEI

    2014-11-01

    Full Text Available This paper proposes an overview of the evolution in the automotive sector in the process of regional development. The fundamental changes made by the component supplier sector improved the regional development and manufacturing process. Automotive industry is one of the modern sectors in many countries that benefits of a high technology impact and creates jobs that reduces unemployment across Europe. The auto industry changed cities, regions and countries into poles of development and it becomes more and more efficient. The high foreign direct investments from the automotive sector play an important role in regional development process. Continuous changes are being made in the economy, society, and company; in conclusion the automotive clusters will always be a subject of analysis.

  9. 78 FR 36633 - National Automotive Sampling System

    Science.gov (United States)

    2013-06-18

    ... National Highway Traffic Safety Administration National Automotive Sampling System AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of the Transportation (DOT). ACTION: Notice of public... regarding vehicle design and traffic safety. The NASS system currently has two components: the...

  10. 77 FR 37471 - National Automotive Sampling System

    Science.gov (United States)

    2012-06-21

    ... National Highway Traffic Safety Administration National Automotive Sampling System AGENCY: National Highway Traffic Safety Administration (NHTSA), Department of Transportation (DOT). ACTION: Notice and request for... make informed regulatory, program, and policy decisions regarding vehicle design and traffic...

  11. Sustainable automotive energy system in China

    CERN Document Server

    CAERC, Tsinghua University

    2014-01-01

    This book identifies and addresses key issues of automotive energy in China. It covers demography, economics, technology and policy, providing a broad perspective to aid in the planning of sustainable road transport in China.

  12. SELECTION METHOD FOR AUTOMOTIVE PARTS RECONDITIONING

    Directory of Open Access Journals (Sweden)

    Dan Florin NITOI

    2015-05-01

    Full Text Available Paper presents technological methods for metal deposition, costs calculation and clasification for the main process that helps in automotive technologies to repair or to increase pieces properties. Paper was constructed based on many technological experiments that starts from practicans and returns to them. The main aim is to help young engineers or practicians engineers to choose the proper reconditioning process with the best information in repairing pieces from automotive industry.

  13. 75 FR 34170 - Plastic Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium Automotive Exteriors, LLC...

    Science.gov (United States)

    2010-06-16

    ... Employment and Training Administration Plastic Omnium Automotive Exteriors, LLC, Anderson, SC; Plastic Omnium... Assistance on March 18, 2010, applicable to workers of Plastic Omnium Automotive Exteriors, LLC, Anderson... have occurred involving workers in support of the Anderson, South Carolina location of Plastic...

  14. Automotive History and Development of the Automobile; Automotive Mechanics I: 9043.01.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    The automotive history and development of the automobile course is designed to familiarize the beginning student with basic concepts common to the automobile history and general information that is required for successful advancement in the automotive mechanics field. A course outline is provided and seven pages of post-tests are included in the…

  15. Automotive Stirling Engine Development Project

    Science.gov (United States)

    Ernst, William D.; Shaltens, Richard K.

    1997-01-01

    The development and verification of automotive Stirling engine (ASE) component and system technology is described as it evolved through two experimental engine designs: the Mod 1 and the Mod 2. Engine operation and performance and endurance test results for the Mod 1 are summarized. Mod 2 engine and component development progress is traced from the original design through hardware development, laboratory test, and vehicle installation. More than 21,000 hr of testing were accomplished, including 4800 hr with vehicles that were driven more dm 59,000 miles. Mod 2 engine dynamometer tests demonstrated that the engine system configuration had accomplished its performance goals for power (60 kW) and efficiency (38.5%) to within a few percent. Tests with the Mod 2 engine installed in a delivery van demonstrated combined metro-highway fuel economy improvements consistent with engine performance goals and the potential for low emission levels. A modified version of the Mod 2 has been identified as a manufacturable design for an ASE. As part of the ASE project, the Industry Test and Evaluation Program (ITEP), NASA Technology Utilization (TU) project, and the industry-funded Stirling Natural Gas Engine program were undertaken to transfer ASE technology to end users. The results of these technology transfer efforts are also summarized.

  16. Green competitiveness research on Chinese automotive enterprises

    Directory of Open Access Journals (Sweden)

    Yuanhui Li

    2014-05-01

    Full Text Available Purpose: More and more executives of automobileindustry in China start to recognize the concept of green competitiveness recently. However, relatively less research attention has been devoted to the consideration of measurement. This paper aims to find empirical approach to quantify green competitiveness for automotive enterprises. The connotation of green competitiveness is explored and one suite of evaluation index system has been proposed with four dimensions including environmental, resource, capability and knowledge.Design/methodology/approach: By introducing the factor analysis method, green competitiveness has been measured through an empirical analysis of 24 automotive enterprises within China.Findings: The results indicate that those elements, such as enterprise resource possession and utilization; environment, responsibility and knowledge; profitability; management efficiency, have significant effect on the green competitiveness for automotive enterprises. The further analysis also unveils the advantages and disadvantages of green competitiveness for each company and the direction for improvement.Research limitations/implications: Guide regulators and managers of automobile industry to take some measures to enhance their green competitive advantage.Practical implications: Provide practical methods to measure green competitiveness for automotive enterprises.Originality/value: This paper proposes an evaluation index system of green competitiveness for automotive enterprises. The suggestions of our research will be beneficial to enterprise executives and industry regulators.

  17. Platinum availability for future automotive technologies.

    Science.gov (United States)

    Alonso, Elisa; Field, Frank R; Kirchain, Randolph E

    2012-12-04

    Platinum is an excellent catalyst, can be used at high temperatures, and is stable in many aggressive chemical environments. Consequently, platinum is used in many current industrial applications, notably automotive catalytic converters, and prospective vehicle fuel cells are expected to rely upon it. Between 2005 and 2010, the automotive industry used approximately 40% of mined platinum. Future automotive industry growth and automotive sales shifts toward new technologies could significantly alter platinum demand. The potential risks for decreased platinum availability are evaluated, using an analysis of platinum market characteristics that describes platinum's geophysical constraints, institutional efficiency, and dynamic responsiveness. Results show that platinum demand for an automotive fleet that meets 450 ppm greenhouse gas stabilization goals would require within 10% of historical growth rates of platinum supply before 2025. However, such a fleet, due largely to sales growth in fuel cell vehicles, will more strongly constrain platinum supply in the 2050 time period. While current platinum reserves are sufficient to satisfy this increased demand, decreasing platinum ore grade and continued concentration of platinum supply in a single geographic area are availability risk factors to platinum end-users.

  18. Branding through trade shows in the automotive industry

    OpenAIRE

    Narui, Jahan

    2013-01-01

    The automotive industry is a major global industry with a great history of exhibitions. As trade shows are getting more attention within studies, the same is not the case for automotive trade shows. Noteworthy, automotive trade shows emphasize non-selling roles such as image-building. This paper seeks to investigate image-building purposes of exhibiting automotive companies using integrated marketing communications (IMC). Data has been gathered from four participating companies in the Geneva ...

  19. Branding through trade shows in the automotive industry

    OpenAIRE

    Narui, Jahan

    2013-01-01

    The automotive industry is a major global industry with a great history of exhibitions. As trade shows are getting more attention within studies, the same is not the case for automotive trade shows. Noteworthy, automotive trade shows emphasize non-selling roles such as image-building. This paper seeks to investigate image-building purposes of exhibiting automotive companies using integrated marketing communications (IMC). Data has been gathered from four participating companies in the Geneva ...

  20. Advanced casting technologies for lightweight automotive applications

    Directory of Open Access Journals (Sweden)

    Alan A. Luo

    2010-11-01

    Full Text Available This paper provides an overview of alloy and process developments in aluminum and magnesium castings for lightweight automotive applications. Wear-resistant aluminum alloys, creep-resistant and high strength/ductility magnesium alloys have been developed for automotive applications. On the process front, vacuum-assisted die casting and high vacuum die casting technologies have been developed for high-integrity body and chassis applications. Thin-wall and hollow casting components are being produced by low-pressure die casting processes for structural applications. Overcasting technology is gaining traction and has enabled mixed material designs for automotive sub-systems such as engine cradles and instrument panel beams. Simulation tools developed to predict the interfacial interactions of the dissimilar components and the structural integrity of the overcast systems are being validated in the casting trials.

  1. My father’s automotive dream

    Institute of Scientific and Technical Information of China (English)

    Rain Chen

    2005-01-01

    <正>Memories of Changchun Changchun literally means ’Long Spring’. The city is located in northeast China’s Jilin province, which literally means ’Lucky Forest’. Since my father is an old worker of Changchun’s Yi Qi(the abbreviation of Changchun First Automotive Factory) plant - China’s earliest automotive plant, I have spent 60 years in the city, graduating from the well-established Jilin University and currently working for a periodical association. A friend from Beijing encouraged me to write my family’s history, and since my family’s story is really a story about the good name of Changchun, an automotive city and a college town, I couldn’t refuse.

  2. Optimization and optimal control in automotive systems

    CERN Document Server

    Kolmanovsky, Ilya; Steinbuch, Maarten; Re, Luigi

    2014-01-01

    This book demonstrates the use of the optimization techniques that are becoming essential to meet the increasing stringency and variety of requirements for automotive systems. It shows the reader how to move away from earlier  approaches, based on some degree of heuristics, to the use of  more and more common systematic methods. Even systematic methods can be developed and applied in a large number of forms so the text collects contributions from across the theory, methods and real-world automotive applications of optimization. Greater fuel economy, significant reductions in permissible emissions, new drivability requirements and the generally increasing complexity of automotive systems are among the criteria that the contributing authors set themselves to meet. In many cases multiple and often conflicting requirements give rise to multi-objective constrained optimization problems which are also considered. Some of these problems fall into the domain of the traditional multi-disciplinary optimization applie...

  3. Automotive Radar Sensors in Silicon Technologies

    CERN Document Server

    Jain, Vipul

    2013-01-01

    This book presents architectures and design techniques for mm-wave automotive radar transceivers. Several fully-integrated transceivers and receivers operating at 22-29 GHz and 77-81 GHz are demonstrated in both CMOS and SiGe BiCMOS technologies. Excellent performance is achieved indicating the suitability of silicon technologies for automotive radar sensors.  This book bridges an existing gap between information available on dependable system/architecture design and circuit design.  It provides the background of the field and detailed description of recent research and development of silicon-based radar sensors.  System-level requirements and circuit topologies for radar transceivers are described in detail. Holistic approaches towards designing radar sensors are validated with several examples of highly-integrated radar ICs in silicon technologies. Circuit techniques to design millimeter-wave circuits in silicon technologies are discussed in depth.  Describes concepts and fundamentals of automotive rada...

  4. Can Distance Learning Be Used to Teach Automotive Management Skills?

    Science.gov (United States)

    Noto, Teresa L.

    2011-01-01

    Today's automotive college students will shape the future of the automobile industry. The success of college-level automotive programs has long been dependent on the students' ability to participate in hands-on classroom based interactions. In this article, distance learning and how it can be used to teach automotive management skills, as well as…

  5. 25 CFR 117.10 - Purchase of automotive equipment.

    Science.gov (United States)

    2010-04-01

    ... 25 Indians 1 2010-04-01 2010-04-01 false Purchase of automotive equipment. 117.10 Section 117.10... COMPETENCY § 117.10 Purchase of automotive equipment. The superintendent may disburse from the surplus funds of an adult Indian not to exceed $2,000 for the purchase of automotive equipment when the...

  6. Best Practices in School-to-Careers: The Automotive Industry.

    Science.gov (United States)

    National Employer Leadership Council, Washington, DC.

    This document highlights the school-to-careers (STC) partnerships connecting workplace experiences to classroom learning to prepare students for successful employment in the automotive industry. First, the current state of the automotive industry is reviewed and the role of STC in addressing automotive service needs is explained. Next, the…

  7. Natural organic matter alters size-dependent effects of nanoCuO on the feeding behaviour of freshwater invertebrate shredders.

    Science.gov (United States)

    Pradhan, Arunava; Geraldes, Paulo; Seena, Sahadevan; Pascoal, Cláudia; Cássio, Fernanda

    2015-12-01

    Nanoparticle size and the presence of natural organic matter (NOM) may influence the toxicity of nanoCuO to aquatic biota, but their interactive effects have been poorly investigated. We examined the feeding behaviour of the invertebrate shredder Allogamus ligonifer when exposed to sublethal concentrations of nanoCuO (50 and 100 mg L(-1)) with three particle sizes (12, 50 and 80 nm) in the absence or presence of humic acid (HA, 100 mg L(-1)) as a proxy of NOM. We further examined the ability of invertebrates to recover from the stressors. In the absence of nanoCuO and HA, the feeding rate of shredders was 0.416 mg leaf DM mg(-1 )animal DM day(-1). The exposure to increased nanoCuO concentrations inhibited the feeding rate and effects were stronger as nanoparticle size decreased (up to 83.3% inhibition for 12 nm particles). The exposure to HA alone inhibited the feeding activity by 52.7%. However, the co-exposure to nanoCuO and HA alleviated the inhibitory effects promoted by smaller and medium sized nanoCuO (up to 29.5%). The recovery of feeding activity by the shredders after stress removal was very low; maximum recovery (16.7%) was found for invertebrates rescued from pre-exposure to lower concentration of nanoCuO with larger size.

  8. Effects of invasive European bird cherry (Prunus padus) on leaf litter processing by aquatic invertebrate shredder communities in urban Alaskan streams

    Science.gov (United States)

    Roon, David A.; Wipfli, Mark S.; Wurtz, Tricia L.

    2014-01-01

    European bird cherry (Prunus padus) (EBC) is an invasive ornamental tree that is spreading rapidly in riparian forests of urban Alaska. To determine how the spread of EBC affects leaf litter processing by aquatic invertebrate shredders, we conducted complementary leaf pack experiments in two streams located in Anchorage, Alaska. The first experiment contrasted invasive EBC with three native tree species—thin-leaf alder (Alnus tenuifolia), paper birch (Betula neoalaskana), and black cottonwood (Populus trichocarpa)—in one reach of Chester Creek; finding that EBC leaf litter broke down significantly faster than birch and cottonwood, but at a similar rate to alder. The second experiment contrasted EBC with alder in four reaches of Campbell and Chester creeks; finding that while EBC leaf litter broke down significantly faster than alder in Chester Creek, EBC broke down at a similar rate to alder in Campbell Creek. Although EBC sometimes supported fewer shredders by both count and mass, shredder communities did not differ significantly between EBC and native plants. Collectively, these data suggest that invasive EBC is not currently exhibiting strong negative impacts on leaf litter processing in these streams, but could if it continues to spread and further displaces native species over time.

  9. New market strategies in the automotive industry

    Directory of Open Access Journals (Sweden)

    Kokić Miljko

    2006-01-01

    Full Text Available The world automotive industry has about 30% of excessive capacity. Regardless of that, the new plants are being constantly built. The countries of the East Europe, China and India are selected as suitable areas by almost all world leading car manufactures to build their additional plants in order to make profits. An open world market is subject to an uncompromising striving for each customer. Our manufacturers have to meet the same requirements if want to offer their products in the world market. Finding out of foreign strategic partners is the fastest way to recover a domestic automotive industry and to increase an employment rate.

  10. Nanotechnology impact on the automotive industry.

    Science.gov (United States)

    Wong, Kaufui V; Paddon, Patrick A

    2014-01-01

    Nanotechnology has been implemented widely in the automotive industry. This technology is particularly useful in coatings, fabrics, structural materials, fluids, lubricants, tires, and preliminary applications in smart glass/windows and video display systems. A special sub-class of improved materials, alternative energy, has also seen a boost from advances in nanotechnology, and continues to be an active research area. A correlation exists in the automotive industry between the areas with increased nanotechnology incorporation and those with increased profit margins via improvements and customer demands.

  11. Research progress of aluminum alloy automotive sheet and application technology

    Institute of Scientific and Technical Information of China (English)

    Ma Mingtu; You Jianghai; Lu Hongzhou; Wang Zhiwen

    2012-01-01

    Pretrcatment technology is deeply discussed to explain its importance in guaranteeing properties and form- ability of aluminum alloy automotive sheet. Some typical applications of aluminum alloy automotive sheet to automotive industry are listed. Based on the author's knowledge and recognition and research progress presently, the important re- search contents about aluminum alloy automotive sheet are emphasized. Reducing cost and price of sheet and going deeply into application research are the main work for expending the application of aluminum alloy automotive sheet in the automobile.

  12. Earning capacity analysis on shredder production line%废钢破碎线收益能力分析

    Institute of Scientific and Technical Information of China (English)

    臧宝泽

    2015-01-01

    As the core manufacture technology of metal recycling companies and important part of metal recycling industry, the shredder production line processes the scraps and scraped cars by crushing and separation. As the important link of connecting metal recycling with smelting, the earning capacity of shredder production line is the critical factor of improving operation and reducing cost. This article analyzed the relationship between earning capacity and impact factors, and constructed the corresponding function model. Based on the function analysis, it is the factors of a metal recycling company's planning, equipment selection, construction, operation, maintenance and management that have been figured out. The conclusion of the analysis could be the reference for scraps recycling corporations and car recycling corporations.%废钢破碎线是金属资源回收企业的核心生产工艺之一,以废金属和报废汽车等为加工原料,以破碎和分选为核心工艺,是金属回收产业的重要组成部分。作为衔接金属资源回收和金属冶炼产业链的重要环节,废钢破碎线的收益能力是金属资源回收企业提升收益能力、降低运营成本的关键因素。对废钢破碎线的收益能力和影响收益能力的各因素进行分析,构建出函数模型,基于函数模型分析,得出金属资源回收企业在废钢破碎线的筹划、选型、投建、使用、运营维护和管理等方面应该重视的因素。其分析结果为废钢回收企业和报废汽车回收企业投资建设提供参考。

  13. Market Opportunities for Automotive Components Used in Non-automotive Applications Manufacturing : Estonian Industrial Market

    OpenAIRE

    Kalajärv, Jaana

    2012-01-01

    This thesis examines the opportunities available for automotive components in the Esto-nian non-automotive industrial market. The literature review part is mainly covers the theory of marketing research, because of the approach chosen for this paper. Only small part of marketing research process is re-searched closer in literature review section, because of the scope of the research. Three most relevant steps for the thesis are chosen from research process for further more in-vestigation,...

  14. On credibility improvements for automotive navigation systems

    NARCIS (Netherlands)

    Schaub, Florian; Hipp, Markus; Kargl, Frank; Weber, Michael

    2012-01-01

    Automotive navigation systems are becoming ubiquitous as driver assistance systems. Vendors continuously aim to enhance route guidance by adding new features to their systems. However, we found in an analysis of current navigation systems that many share interaction weaknesses, which can damage the

  15. International Conference on Vehicle and Automotive Engineering

    CERN Document Server

    Bolló, Betti

    2017-01-01

    This book presents the proceedings of the first vehicle engineering and vehicle industry conference. It captures the outcome of theoretical and practical studies as well as the future development trends in a wide field of automotive research. The themes of the conference include design, manufacturing, economic and educational topics.

  16. Training Issues for the European Automotive Industry

    NARCIS (Netherlands)

    Dankbaar, B.

    1996-01-01

    Provides an overview of the results of an investigation carried out for the European Commission. Aims to identify themes and issues in the field of continuing training in the European automotive industry. A large number of interviews were carried out in all the major car manufacturing countries of

  17. Training issues for the European automotive industry

    NARCIS (Netherlands)

    Dankbaar, B.

    1999-01-01

    Provides an overview of the results of an investigation carried out for the European Commission. Aims to identify themes and issues in the field of continuing training in the European automotive industry. A large number of interviews were carried out in all the major car manufacturing countries of

  18. Green innovation adoption in automotive supply chain

    DEFF Research Database (Denmark)

    Zailani, Suhaiza; Govindan, Kannan; Iranmanesh, Mohammad

    2015-01-01

    Green innovation has currently been receiving a great deal of international attention because of the growing concern of consumers, governments, and the community as a whole with regard to the degradation of natural resources and environmental pollution. The automotive sector is one of the leading...

  19. Metrics for Automotive Merchandising, Petroleum Marketing.

    Science.gov (United States)

    Cooper, Gloria S., Ed.; Magisos, Joel H., Ed.

    Designed to meet the job-related metric measurement needs of students in automotive merchandising and petroleum marketing classes, this instructional package is one of five for the marketing and distribution cluster, part of a set of 55 packages for metric instruction in different occupations. The package is intended for students who already know…

  20. Solidification studies of automotive heat exchanger materials

    Science.gov (United States)

    Carlberg, T.; Jaradeh, M.; Kamgou Kamaga, H.

    2006-11-01

    Modifications of the aluminum alloy AA 3003 have been studied to improve and tailorits properties for applications in automotive heat exchangers. Laboratory techniques have been applied to simulate industrial direct-chill casting, and some basic solidification studies have been conducted. The results are coupled to structures observed in industrial-size ingots and discussed in terms of structure-property relations.

  1. Techno-economic requirements for automotive composites

    Science.gov (United States)

    Arnold, Scot

    1993-01-01

    New technology generally serves two main goals of the automotive industry: one is to enable vehicles to comply with various governmental regulations and the other is to provide a competitive edge in the market. The latter goal can either be served through improved manufacturing and design capabilities, such as computer aided design and computer aided manufacturing, or through improved product performance, such as anti-lock braking (ABS). Although safety features are sometimes customer driven, such as the increasing use of airbags and ABS, most are determined by regulations as outlined by the Federal Motor Vehicle Safety Standards (FMVSS). Other standards, set by the Environmental Protection Agency, determine acceptable levels of emissions and fuel consumption. State governments, such as in California, are also setting precedent standards, such as requiring manufacturers to offer zero-emission vehicles as a certain fraction of their sales in the state. The drive to apply new materials in the automobile stems from the need to reduce weight and improve fuel efficiency. Topics discussed include: new lightweight materials; types of automotive materials; automotive composite applications; the role for composite materials in automotive applications; advantages and disadvantages of composite materials; material substitution economics; economic perspective; production economics; and composite materials production economics.

  2. A listening test system for automotive audio

    DEFF Research Database (Denmark)

    Christensen, Flemming; Geoff, Martin; Minnaar, Pauli;

    2005-01-01

    This paper describes a system for simulating automotive audio through headphones for the purposes of conducting listening experiments in the laboratory. The system is based on binaural technology and consists of a component for reproducing the sound of the audio system itself and a component...

  3. Aero and vibroacoustics of automotive turbochargers

    Energy Technology Data Exchange (ETDEWEB)

    Nguyen-Schaefer, Hung [Bosch Mahle Turbo Systems GmbH, Stuttgart (Germany)

    2013-02-01

    First book about the aeroacoustics of automotive turbochargers. Author of the book ''Rotordynamics of Automotive Turbochargers'', Springer, 2012. Written by an R and D expert in the turbocharger industry. Aero and Vibroacoustics of Automotive Turbochargers is a topic involving aspects from the working fields of thermodynamics of turbomachinery, aerodynamics, rotordynamics, and noise propagation computation. In this broadly interdisciplinary subject, thermodynamics of turbomachinery is used to design the turbocharger and to determine its operating conditions. Aerodynamics is needed to study the compressor flow dynamics and flow instabilities of rotating stall and surge, which can produce growling and whining-type noises. Rotordynamics is necessary to study rotor unbalance and self-excited oil-whirl instabilities, which lead to whistling and constant tone-type noises in rotating floating oil-film type bearings. For the special case of turbochargers using ball bearings, some high-order harmonic and wear noises also manifest in the rotor operating range. Lastly, noise propagation computation, based on Lighthill's analogy, is required to investigate airborne noises produced by turbochargers in passenger vehicles. The content of this book is intended for advanced undergraduates, graduates in mechanical engineering, research scientists and practicing engineers who want to better understand the interactions between these working fields and the resulting impact on the interesting topic of Aero and Vibroacoustics of Automotive Turbochargers.

  4. BATTERIES 2020 – A Joint European Effort towards European Competitive Automotive Batteries

    DEFF Research Database (Denmark)

    Timmermans, J.-M.; Rodriguez-Martinez, L.M.; Omar, N.

    The Integrated Project “Batteries 2020” unites 9 European partners jointly working on the research and development of European competitive automotive batteries. The project aims at increasing lifetime and energy density of large format high-energy lithium-ion batteries towards the goals targeted...... for automotive batteries. Three parallel strategies will be followed in order to achieve those targets: (i) Highly focused materials development; two improved generations of NMC materials will allow the performance, stability and cyclability of state of the art cells to be improved. (ii) Understanding ageing...... of degradation processes. (iii) Reduction of battery cost; a way to reduce costs, increase battery residual value and improve sustainability is to consider second life uses of batteries used in EV. These batteries are still operational and suitable to less restrictive conditions, such as those for stationary...

  5. Release to the gas phase of metals, S and Cl during combustion of dedicated waste fractions

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; van Lith, Simone Cornelia; Frandsen, Flemming

    2010-01-01

    wood, shoes, automotive shredder waste and PVC (poly-vinyl-chloride). The waste fractions were characterized by use of wet chemical analysis, and, based on the chemical composition of the initial fuel sample and the ash residue after the experiments; the release of inorganic elements was quantified...

  6. Platform Based Design for Automotive Sensor Conditioning

    CERN Document Server

    Fanucci, L; Iozzi, F; Marino, C; Rocchi, A

    2011-01-01

    In this paper a general architecture suitable to interface several kinds of sensors for automotive applications is presented. A platform based design approach is pursued to improve system performance while minimizing time-to-market.. The platform is composed by an analog front-end and a digital section. The latter is based on a microcontroller core (8051 IP by Oregano) plus a set of dedicated hardware dedicated to the complex signal processing required for sensor conditioning. The microcontroller handles also the communication with external devices (as a PC) for data output and fast prototyping. A case study is presented concerning the conditioning of a Gyro yaw rate sensor for automotive applications. Measured performance results outperform current state-of-the-art commercial devices.

  7. Polymer matrix nanocomposites for automotive structural components

    Science.gov (United States)

    Naskar, Amit K.; Keum, Jong K.; Boeman, Raymond G.

    2016-12-01

    Over the past several decades, the automotive industry has expended significant effort to develop lightweight parts from new easy-to-process polymeric nanocomposites. These materials have been particularly attractive because they can increase fuel efficiency and reduce greenhouse gas emissions. However, attempts to reinforce soft matrices by nanoscale reinforcing agents at commercially deployable scales have been only sporadically successful to date. This situation is due primarily to the lack of fundamental understanding of how multiscale interfacial interactions and the resultant structures affect the properties of polymer nanocomposites. In this Perspective, we critically evaluate the state of the art in the field and propose a possible path that may help to overcome these barriers. Only once we achieve a deeper understanding of the structure-properties relationship of polymer matrix nanocomposites will we be able to develop novel structural nanocomposites with enhanced mechanical properties for automotive applications.

  8. Automotive Stirling engine: Mod 2 design report

    Science.gov (United States)

    Nightingale, Noel P.

    1986-01-01

    The design of an automotive Stirling engine that achieves the superior fuel economy potential of the Stirling cycle is described. As the culmination of a 9-yr development program, this engine, designated the Mod 2, also nullifies arguments that Stirling engines are heavy, expensive, unreliable, demonstrating poor performance. Installed in a General Motors Chevrolet Celebrity car, this engine has a predicted combined fuel economy on unleaded gasoline of 17.5 km/l (41 mpg)- a value 50% above the current vehicle fleet average. The Mod 2 Stirling engine is a four-cylinder V-drive design with a single crankshaft. The engine is also equipped with all the controls and auxiliaries necessary for automotive operation.

  9. Lightweight Steel Solutions for Automotive Industry

    Science.gov (United States)

    Lee, Hong Woo; Kim, Gyosung; Park, Sung Ho

    2010-06-01

    Recently, improvement in fuel efficiency and safety has become the biggest issue in worldwide automotive industry. Although the regulation of environment and safety has been tightened up more and more, the majority of vehicle bodies are still manufactured from stamped steel components. This means that the optimized steel solutions enable to demonstrate its ability to reduce body weight with high crashworthiness performance instead of expensive light weight materials such as Al, Mg and composites. To provide the innovative steel solutions for automotive industry, POSCO has developed AHSS and its application technologies, which is directly connected to EVI activities. EVI is a technical cooperation program with customer covering all stages of new car project from design to mass production. Integrated light weight solutions through new forming technologies such as TWB, hydroforming and HPF are continuously developed and provided for EVI activities. This paper will discuss the detailed status of these technologies especially light weight steel solutions based on innovative technologies.

  10. Springback prediction of TWIP automotive sheets

    Science.gov (United States)

    Ahn, Kanghwan; Yoo, Donghoon; Seo, Min Hong; Park, Sung-Ho; Chung, Kwansoo

    2009-08-01

    In an effort to reduce the weight of vehicles, automotive companies are replacing conventional steel parts with light weight alloys and/or with advanced high strength steels (AHSS) such as dual-phase (DP), twinning induced plasticity (TWIP), and transformation induced plasticity (TRIP) steels. The main objective of this work is to experimentally and numerically evaluate the macro-performance of the automotive TWIP sheet in conjunction with springback. In order to characterize the mechanical properties, simple tension and tension-compression tests were performed to determine anisotropic properties, as well as the Bauschinger, transient, and permanent softening behaviors during reverse loading. For numerical simulations, the anisotropic yield function Yld2000-2d was utilized along with the combined isotropic-kinematic hardening law based on the modified Chaboche model. Springback verification was performed for the unconstrained cylindrical bending and 2D draw bending tests.

  11. Development of light metals automotive structural subsystems

    Energy Technology Data Exchange (ETDEWEB)

    Luo, A.A.; Sachdev, A.K. [General Motors Research and Development Center, Warren, MI (United States)

    2007-07-01

    Key technological developments in aluminum and magnesium alloys were reviewed in relation to the manufacturing processes that enable lightweight automotive structural subsystems. Examples included the materials and processes evolution of lightweight body structures, chassis systems, and instrument panel beams. New aluminum and magnesium alloys and manufacturing technologies used to reduce mass and improve performance in vehicle cradle structures were discussed. Hydroforming processes used to enable the use of lightweight aluminum alloy tubes in automotive body structures were also reviewed, in addition to body architectures enabled by different materials and manufacturing processes. The review noted that magnesium instrument panels are now being designed to provide significant performance improvement, reduced vibration, and enhanced crashworthiness in new automobiles. It was concluded that vehicles will incorporate more lightweight materials such as nanocomposites and aluminum and magnesium sheets. 9 refs., 10 figs.

  12. Innovation and Entrepreneurship in the Automotive Business

    DEFF Research Database (Denmark)

    2011-01-01

    invention have appropriate benefits. The timing of the dialog with a potential user or business partner is important when it comes to which issues that have highest priorities or are most frequently discussed in the organization of said user or business partner. If there exist a special issue that your idea......The global automotive business is one of the most competitive environment you can imagine. As an independent inventor or as a small development company it is very challenging to be successful in implementing new ideas and components. In this mature and somewhat conservative technical environment...... address you will have a much better access the decision making process and get enough interest for a potential business deal. After 20 years as a supplier of engineering services to the automotive industry and 10 years as head of Global R&D at Scania CV AB, I have experienced pros and cons both from...

  13. Polymer matrix nanocomposites for automotive structural components.

    Science.gov (United States)

    Naskar, Amit K; Keum, Jong K; Boeman, Raymond G

    2016-12-06

    Over the past several decades, the automotive industry has expended significant effort to develop lightweight parts from new easy-to-process polymeric nanocomposites. These materials have been particularly attractive because they can increase fuel efficiency and reduce greenhouse gas emissions. However, attempts to reinforce soft matrices by nanoscale reinforcing agents at commercially deployable scales have been only sporadically successful to date. This situation is due primarily to the lack of fundamental understanding of how multiscale interfacial interactions and the resultant structures affect the properties of polymer nanocomposites. In this Perspective, we critically evaluate the state of the art in the field and propose a possible path that may help to overcome these barriers. Only once we achieve a deeper understanding of the structure-properties relationship of polymer matrix nanocomposites will we be able to develop novel structural nanocomposites with enhanced mechanical properties for automotive applications.

  14. General Motors automotive fuel cell program

    Energy Technology Data Exchange (ETDEWEB)

    Fronk, M.H.

    1995-08-01

    The objectives of the second phase of the GM/DOE fuel cell program is to develop and test a 30 kW fuel cell powerplant. This powerplant will be based on a methanol fuel processor and a proton exchange membrane PM fuel cell stack. In addition, the 10 kW system developed during phase I will be used as a {open_quotes}mule{close_quotes} to test automotive components and other ancillaries, needed for transient operation.

  15. Occupational skin diseases in automotive industry workers.

    Science.gov (United States)

    Yakut, Yunus; Uçmak, Derya; Akkurt, Zeynep Meltem; Akdeniz, Sedat; Palanci, Yilmaz; Sula, Bilal

    2014-03-01

    Studies on occupational skin diseases in workers of the automotive industry are few. To investigate the prevalence of occupational skin diseases in workers of the automotive industry. Between September and December 2011, a total of 405 workers from the automotive repair industry in Diyarbakır were interviewed. They were active workers in the repair industry who had been employed for at least six months. Business owners, sellers of spare parts and accounting officers were not included. The employees were examined at their workplaces and the working conditions were observed. Detailed dermatological examination was performed. The mean age of the 405 workers who participated in the study was 27.7 ± 10.3. The mean working time of employees was 13.3 ± 10.4 years. All of the employees were male. Dermatological diseases were not detected in 144 out of 405 workers (35.6%) and at least one condition was diagnosed in 261 (64.4%). The most frequent diagnosis was callus, hyperkeratosis, clavus (27.7%), followed by nail changes (16.8%) and superficial mycoses (12.1%). Contact dermatitis was seen at a rate of 5.9%. Traumatic lesions such as hyperkeratotic lesions and nail changes were found most frequently. Traumatic lesions were common among individuals who did not use gloves. Most nail changes were localized leuconychia, a finding not reported in the studies on automotive industry workers. In accordance with the literature, irritant contact dermatitis was observed in patients with a history of atopy and who had been working for a long time. Occupational skin diseases comprise an important field in dermatology, deserving much attention. Further studies on occupational dermatology are necessary.

  16. INNOVATION LEAN PRINCIPLES IN AUTOMOTIVE GREEN MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Dušan Sabadka

    2014-12-01

    Full Text Available Today, industries such as automotive and manufacturing industries deal with a lot of environmental regulations. Lean is a production strategy whose fundamental principles drive the industry towards a more effective production of goods and services. The eco-efficiency concept is primary to sustainable development and intends to provide more value with less environmental impact. The aim of this study is to identify and explore the contributions of Lean to reduce environmental impacts that naturally result from industrial activity.

  17. MICROALLOYED STEELS FOR THE AUTOMOTIVE INDUSTRY

    OpenAIRE

    Debanshu Bhattacharya

    2014-01-01

    Two major drivers for the use of newer steels in the automotive industry are fuel efficiency and increased safety performance. Fuel efficiency is mainly a function of weight of steel parts, which in turn, is controlled by gauge and design. Safety is determined by the energy absorbing capacity of the steel used to make the part. All of these factors are incentives for the U.S. automakers to use both Highly Formable and Advanced High Strength Steels (AHSS) to replace the conventional ...

  18. Characterization of three-way automotive catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kenik, E.A.; More, K.L. [Oak Ridge National Lab., TN (United States); LaBarge, W. [Delphi Automotive Systems, Flint, MI (United States)] [and others

    1997-04-01

    The CRADA between Delphi Automotive Systems (Delphi; formerly General Motors - AC Delco, Systems) and Lockheed Martin Energy Research (LMER) on automotive catalysts was completed at the end of FY96, after a ten month, no-cost extension. The CRADA was aimed at improved performance and lifetime of noble metal based three-way-catalysts (TWC), which are the primary catalytic system for automotive emission control systems. While these TWC can meet the currently required emission standards, higher than optimum noble metal loadings are often required to meet lifetime requirements. In addition, more stringent emission standards will be imposed in the near future, demanding improved performance and service life from these catalysts. Understanding the changes of TWC conversion efficiency with ageing is a critical need in improving these catalysts. Initially in a fresh catalyst, the active material is often distributed on a very fine scale, approaching single atoms or small atomic clusters. As such, a wide range of analytical techniques have been employed to provide high spatial resolution characterization of the evolving state of the catalytic material.

  19. Does long-term fungicide exposure affect the reproductive performance of leaf-shredders? A partial life-cycle study using Hyalella azteca.

    Science.gov (United States)

    Baudy, Patrick; Zubrod, Jochen P; Konschak, Marco; Weil, Mirco; Schulz, Ralf; Bundschuh, Mirco

    2017-03-01

    Leaf-shredding amphipods play a critical role in the ecosystem function of leaf litter breakdown, a key process in many low order streams. Fungicides, however, may adversely influence shredders' behavior and the functions they provide, while there is only limited knowledge concerning effects on their reproductive performance. To assess the latter, a semi-static 56-day partial life-cycle bioassay using the model shredder Hyalella azteca (n = 30) was performed applying two environmentally relevant concentrations of a model fungicide mixture (i.e., 5 and 25 μg/L) composed of five fungicides with different modes of toxic action. Variables related to the food processing (leaf consumption and feces production), growth (body length and dry weight), energy reserves (lipid content), and reproduction (amplexus pairs, number and length of offspring) were determined to understand potential implications in the organisms' energy budget. While the fungicides did not affect leaf consumption, both fungicide treatments significantly reduced amphipods' feces production (∼20%) compared to the control. This observation suggests an increased food utilization to counteract the elevated and stress-related energy demand: although growth as well as energy reserves were unaffected, amplexus pairs were less frequently observed in both fungicide treatments (∼50-100%) suggesting a tradeoff regarding energy allocation favoring the maintenance of fundamental functions at the organism level over reproduction. As a result, the time to release of first offspring was delayed in both fungicide treatments (7 and 14 days) and the median number of offspring was significantly lower in the 25-μg/L treatment (100%), whereas offspring length remained unaffected. The results of this study thus indicate that chronic fungicide exposures can negatively impact shredders' reproductive performance. This may translate into lower abundances and thus a reduced contribution to leaf litter breakdown in

  20. POTENTIAL USE OF MAGNESIUM ALLOYS FOR THE AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Kudret KANDEMİR

    2003-01-01

    Full Text Available Recently, there is a high interest in using lightweight materials for automotive applications where weight reduction and improvement in comfort are needed. Magnesium alloys with excellent specific strength and stiffness properties can be comparable with steel and aluminum alloys for applications in the automotive industry. For this reason, the properties of magnesium alloys are in the focus of research. This study aims at reviewing and evaluating the prospects of magnesium alloys use and applications in the automotive industry.

  1. Technology Improvement of Shredder based on self-defined communication protocol%基于双机通讯的碎纸机技术改进

    Institute of Scientific and Technical Information of China (English)

    张晓涛

    2011-01-01

    According to the current problems of shredder, this paper introduced an improvement scheme based on self-defined communication protocol. This scheme proves to be effective from mass production and can bring good economic benefit.%针对当前碎纸机存在的成本较高、连线复杂等问题,采用基于自定义通讯协议的方案进行改进.大量生产实践证明,此方案行之有效,取得良好的经济效益.

  2. 40 CFR 426.70 - Applicability; description of the automotive glass laminating subcategory.

    Science.gov (United States)

    2010-07-01

    ... automotive glass laminating subcategory. 426.70 Section 426.70 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS GLASS MANUFACTURING POINT SOURCE CATEGORY Automotive Glass Laminating Subcategory § 426.70 Applicability; description of the automotive...

  3. Final report: U.S. competitive position in automotive technologies

    Energy Technology Data Exchange (ETDEWEB)

    Albert, Michael B.; Cheney, Margaret; Thomas, Patrick; Kroll, Peter

    2002-09-30

    Patent data are presented and analyzed to assess the U.S. competitive position in eleven advanced automotive technology categories, including automotive fuel cells, hydrogen storage, advanced batteries, hybrid electric vehicles and others. Inventive activity in most of the technologies is found to be growing at a rapid pace, particularly in advanced batteries, automotive fuel cells and ultracapacitors. The U.S. is the clear leader in automotive fuel cells, on-board hydrogen storage and light weight materials. Japan leads in advanced batteries, hybrid electric vehicles, ultracapacitors, and appears to be close to overtaking the U.S. in other areas of power electronics.

  4. AUTOMOTIVE MARKET- FROM A GENERAL TO A MARKET SEGMENTATION APPROACH

    National Research Council Canada - National Science Library

    Liviana Andreea Niminet

    2014-01-01

    Automotive market and its corresponding industry are undoubtedly of outmost importance and therefore proper market segmentation is crucial for market players, potential competitors and customers as well...

  5. AUTOMOTIVE MARKET- FROM A GENERAL TO A MARKET SEGMENTATION APPROACH

    Directory of Open Access Journals (Sweden)

    Liviana Andreea Niminet

    2014-01-01

    Full Text Available Automotive market and its corresponding industry are undoubtedly of outmost importance and therefore proper market segmentation is crucial for market players, potential competitors and customers as well. Time has proved that market economic analysis often shown flaws in determining the relevant market, by using solely or mainly the geographic aspect and disregarding the importance of segments on the automotive market. For these reasons we propose a new approach of the automotive market proving the importance of proper market segmentation and defining the strategic groups within the automotive market.

  6. United States Automotive Materials Partnership LLC (USAMP)

    Energy Technology Data Exchange (ETDEWEB)

    United States Automotive Materials Partnership

    2011-01-31

    The United States Automotive Materials Partnership LLC (USAMP) was formed in 1993 as a partnership between Chrysler Corporation, Ford Motor Company, and General Motors Corporation. Since then the U.S. Department of Energy (DOE) has supported its activities with funding and technical support. The mission of the USAMP is to conduct vehicle-oriented research and development in materials and materials processing to improve the competitiveness of the U.S. Auto Industry. Its specific goals are: (1) To conduct joint research to further the development of lightweight materials for improved automotive fuel economy; and (2) To work with the Federal government to explore opportunities for cooperative programs with the national laboratories, Federal agencies such as the DOE and universities. As a major component of the DOE's Office of FreedomCAR and Vehicle Technologies Program (FCVT) collaboration with the USAMP, the Automotive Lightweighting Materials (ALM) program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The FCVT was announced in FY 2002 and implemented in FY 2003, as a successor of the Partnership for a New Generation of Vehicles (PNGV), largely addressed under the first Cooperative Agreement. This second USAMP Cooperative Agreement with the DOE has expanded a unique and valuable framework for collaboratively directing industry and government research efforts toward the development of technologies capable of solving important societal problems related to automobile transportation. USAMP efforts are conducted by the domestic automobile manufacturers, in collaboration with materials and manufacturing suppliers, national laboratories, universities, and other technology or trade organizations. These interactions provide a direct route for implementing newly

  7. Residuation theory

    CERN Document Server

    Blyth, T S; Sneddon, I N; Stark, M

    1972-01-01

    Residuation Theory aims to contribute to literature in the field of ordered algebraic structures, especially on the subject of residual mappings. The book is divided into three chapters. Chapter 1 focuses on ordered sets; directed sets; semilattices; lattices; and complete lattices. Chapter 2 tackles Baer rings; Baer semigroups; Foulis semigroups; residual mappings; the notion of involution; and Boolean algebras. Chapter 3 covers residuated groupoids and semigroups; group homomorphic and isotone homomorphic Boolean images of ordered semigroups; Dubreil-Jacotin and Brouwer semigroups; and loli

  8. Automotive Air Conditioning and Heating; Automotive Mechanics (Advanced): 9047.04.

    Science.gov (United States)

    Dade County Public Schools, Miami, FL.

    This document presents an outline for a 135-hour course designed to provide the student with all the foundations necessary to become employable in the automotive air conditioning and heating trade. The course of study includes an orientation to the world of work, the elementary physics of air conditioning and heating, and laboratory experiments…

  9. 废旧木质材料切碎机的研发设计%Research and Development Design of Waste and Old Wood Material Shredders

    Institute of Scientific and Technical Information of China (English)

    刘强; 朱典想; 郭东升

    2013-01-01

      针对多数废旧木质材料形状不规则的特点,设计了一种对原料具有广泛适用性的新型切碎机。简要阐述了切碎机的工作原理,重点介绍了液压推料装置、切削机构和出料装置的设计方法,同时对切碎机的主要技术性能参数进行了设计计算。%In view of the characteristics of various irregular shapes of old and waste wood materials, a new shredder for various kinds of raw materials is designed, and the working principle of this shredder is briefly stated, with focus put on the its hydraulic pusher device, cutting mechanism and discharge unit and the design calculation of its main technical performance parameters conducted.

  10. Type B accident investigation board report of the July 2, 1997 curium intake by shredder operator at Building 513 Lawrence Livermore National Laboratory, Livermore, California. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-08-01

    On July 2, 1997 at approximately 6:00 A.M., two operators (Workers 1 and 2), wearing approved personal protective equipment (PPE), began a shredding operation of HEPA filters for volume reduction in Building 513 (B-513) at Lawrence Livermore National Laboratory (LLNL). The waste requisitions indicated they were shredding filters containing {le} 1 {micro}Ci of americium-241 (Am-241). A third operator (Worker 3) provided support to the shredder operators in the shredding area (hot area) from a room that was adjacent to the shredding area (cold area). At Approximately 8:00 A.M., a fourth operator (Worker 4) relieved Worker 2 in the shredding operation. Sometime between 8:30 A.M. and 9:00 A.M., Worker 3 left the cold area to make a phone call and set off a hand and foot counter in Building 514. Upon discovering the contamination, the shredding operation was stopped and surveys were conducted in the shredder area. Surveys conducted on the workers found significant levels of contamination on their PPE and the exterior of their respirator cartridges. An exit survey of Worker 1 was conducted at approximately 10:05 A.M., and found contamination on his PPE, as well as on the exterior and interior of his respirator. Contamination was also found on his face, chest, back of neck, hair, knees, and mustache. A nose blow indicated significant contamination, which was later determined to be curium-244.

  11. Nanofluids with CNTs for automotive applications

    Science.gov (United States)

    Srinivas, V.; Moorthy, Ch. V. K. N. S. N.; Dedeepya, V.; Manikanta, P. V.; Satish, V.

    2016-04-01

    This paper summarizes a recent work on anti-corrosive and enhanced heat transfer properties of carboxylated water based nanofluids. DI water mixed with Sebacic acid (C10H18O4) as carboxylate additive is dispersed with multi walled carbon nanotubes and tested for corrosion and heat transfer characteristics. Corrosion studies made as per ASTM D 1384 show that carboxylate water dispersed with MWCNTs is resistant to corrosion and hence suitable for automotive environment. In addition to MWCNTs, carboxylated water dispersed with nano sized silver, copper and Aluminium oxide are also tested for corrosion performance but found to be giving considerable corrosion in automotive environment. The stability of MWCNT based nanofluids in terms of zeta potential is found to be good with carboxylated water compared to DI water. Significant improvement is observed in the thermal conductivity of nanofluids dispersed with MWCNTs. There is a slight increase in viscosity and marginal decrease in the specific heat of nanofluids with addition of carboxylate as well as MWCNTs. The carboxylated water is dispersed with very low mass concentration of multi walled carbon nano tubes at 0.025, 0.05 and 0.1 % and tested for heat transfer performance. The heat transfer studies are made in Reynolds number range of 2500-6000 in the developing flow regime. The heat transfer performance of nanofluids is carried out on an air cooled heat exchanger similar to an automotive radiator with incoming air velocities across radiator maintained at 5, 10 and 15 m/s. The coolant side overall heat transfer coefficient and overall heat transfer coefficient have improved markedly. It is also found that the velocity of air and flow rate of coolant plays an important role in enhancement of overall heat transfer coefficient. Stanton number correlation for the entire data has been developed. It is found that the wall temperature gradients play an important role in the enhancement of heat transfer when nanofluids are

  12. An Overview of NASA Automotive Component Reliability Studies

    Science.gov (United States)

    Sampson, Michael J.

    2016-01-01

    The results of NASAs studies into the appropriateness of using US Automotive electronic parts in NASA spaceflight systems will be presented. The first part of the presentation provides an overview of the United States Automotive Electronics Councils AECQ standardization program, the second part provides a summary of the results of NASAs procurement and testing experiences and other lessons learned along with preliminary test results.

  13. 76 FR 40591 - Coordinating Policies on Automotive Communities and Workers

    Science.gov (United States)

    2011-07-11

    ... Policies on Automotive Communities and Workers By the authority vested in me as President by the.... Over the last decade, the United States has experienced a decline in employment in the automotive industry and among part suppliers. This decline accelerated dramatically from 2008 to 2009, with more...

  14. Manual Drivetrain and Axles Specialist. Teacher Edition. Automotive Service Series.

    Science.gov (United States)

    Oklahoma State Dept. of Vocational and Technical Education, Stillwater. Curriculum and Instructional Materials Center.

    This instructor's guide contains materials for teaching the manual drive trains and axle specialist component of a competency-based instructional program for students preparing for employment in the automotive service trade. It is based on National Institute of Automotive Service Excellence task lists. Six instructional units contain materials…

  15. Building best practice automotive after sales network : The Volkswagen case

    NARCIS (Netherlands)

    Mikolik, Gerlinde

    2017-01-01

    This thesis aims to analyze the service operations and networks in the automotive industry as research into the automotive After Sales service network lacks the necessary fine details and industrial feedback. Its purpose is to present the insights and lessons learned from studying the After Sales se

  16. Building best practice automotive after sales network : The Volkswagen case

    NARCIS (Netherlands)

    Mikolik, Gerlinde

    2017-01-01

    This thesis aims to analyze the service operations and networks in the automotive industry as research into the automotive After Sales service network lacks the necessary fine details and industrial feedback. Its purpose is to present the insights and lessons learned from studying the After Sales

  17. Electrohydraulic Forming of Near Net Shape Automotive Panels

    Energy Technology Data Exchange (ETDEWEB)

    None

    2009-01-01

    This factsheet describes a research project whose goal is to develop the electrohydraulic forming (EHF) process as a near net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures.

  18. Dynamic characteristics of automotive steel sheets

    Directory of Open Access Journals (Sweden)

    M. Mihaliková

    2016-10-01

    Full Text Available The aim of this experimental research was to perform an analysis of deformation characteristics on two different types of steel: IF steel, and micro-alloyed steel were used automotive industry. For that purpose changes of properties of these materials were carried out by static 10-3 · s-1 and dynamic 103 · s-1 strain rate assess its plastic properties. Vickers micro hardness test was carried out by the static and dynamic loading condition and describes different hardness distribution. The higher strain hardening of materials was obtained too that was confirmed by distribution of dislocations.

  19. Characterization of three-way automotive catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Kenik, E.A.; More, K.L. [Oak Ridge National Laboratory, TN (United States); LaBarge, W. [General Motors-AC Delco Systems, Flint, MI (United States)] [and others

    1995-05-01

    This has been the second year of a CRADA between General Motors - AC Delco Systems (GM-ACDS) and Martin Marietta Energy Systems (MMES) aimed at improved performance/lifetime of platinum-rhodium based three-way-catalysts (TWC) for automotive emission control systems. While current formulations meet existing emission standards, higher than optimum Pt-Rh loadings are often required. In additionk, more stringent emission standards have been imposed for the near future, demanding improved performance and service life from these catalysts. Understanding the changes of TWC conversion efficiency with ageing is a critical need in improving these catalysts.

  20. Industrial thermoforming simulation of automotive fuel tanks

    Energy Technology Data Exchange (ETDEWEB)

    Wiesche, S. aus der [Kautex Textron GmbH and Co., Bonn (Germany)

    2004-11-01

    An industrial thermoforming simulation with regard to automotive plastic fuel tanks is presented including all relevant process stages. The radiative and conductive heat transfer during the reheat stage, the deformation and stress behaviour during the forming stage, and the final cooling stage are simulated. The modelling of the thermal and rheological behaviour of the involved material is investigated in greater detail. By means of experimental data it is found that modelling of the phase transition during the process is highly important for predicting correct wall thickness distributions. (author)

  1. Advanced Microsystems for Automotive Applications 2005

    Science.gov (United States)

    Valldorf, Jürgen; Gessner, Wolfgang

    Since 1995 the annual international forum on Advanced Microsystems for Automotive Applications (AMAA) has been held in Berlin. The event offers a unique opportunity for microsystems component developers, system suppliers and car manufacturers to show and to discuss competing technological approaches of microsystems based solutions in vehicles. The book accompanying the event has demonstrated to be an efficient instrument for the diffusion of new concepts and technology results. The present volume including the papers of the AMAA 2005 gives an overview on the state-of-the-art and outlines imminent and mid-term R&D perspectives.

  2. Advanced sheet steels for automotive applications

    Science.gov (United States)

    Fekete, James R.; Strugala, Donald C.; Yao, Zhicong

    1992-01-01

    Vacuum degassing has recently been used by sheet steel producers to improve their products' ductility and strength. Carbon contents can be reduced by an order of magnitude to less than 0.0030 wt.%. Through careful alloying and processing, a range of new steel products has been developed for the automotive industry. These products include interstitial-free, deep-drawing-quality steels; formable, high-strength, interstitial-free steels; and bake-hardenable steels. This article summarizes the chemistry and processing needed to produce these products.

  3. AGT 100 automotive gas turbine system development

    Science.gov (United States)

    Helms, H. E. G.

    1982-01-01

    General Motors is developing an automotive gas turbine system that can be an alternate powerplant for future automobiles. Work sponsored by DOE and administered by NASA Lewis Research Center is emphasizing small component aerodynamics and high-temperature structural ceramics. Reliability requirements of the AGT 100 turbine system include chemical and structural ceramic component stability in the gas turbine environment. The power train system, its configuration and schedule are presented, and its performance tested. The aerodynamic component development is reviewed with discussions on the compressor, turbine, regenerator, interturbine duct and scroll, and combustor. Ceramic component development is also reviewed, and production cost and required capital investment are taken into consideration.

  4. Research with neutron and synchrotron radiation on aerospace and automotive materials and components

    Energy Technology Data Exchange (ETDEWEB)

    Kaysser, Wolfgang; Abetz, Volker; Huber, Norbert; Kainer, Karl Ulrich; Pyczak, Florian; Schreyer, Andreas; Staron, Peter [Helmholtz-Zentrum Geesthacht Zentrum fuer Material und Kuestenforschung, Geesthacht (Germany); Esslinger, Joerg [MTU Aero Engines GmbH, Muenchen (Germany); Klassen, Thomas [Helmholtz-Zentrum Geesthacht Zentrum fuer Material und Kuestenforschung, Geesthacht (Germany); Helmut Schmidt Universitaet, Hamburg (Germany)

    2011-08-15

    Characterization with neutrons and synchrotron radiation has yielded essential contributions to the research and development of automotive and aerospace materials, processing methods, and components. This review mainly emphasises developments related to commercial passenger airplanes and light-duty cars. Improved and partly new materials for the reduction of airframe weight and joining by laser-beam welding and friction stir welding are ongoing areas of assessment. Chemical reactions, microstructure development, and residual stresses are frequently measured. Polymers and polymer matrix composites often require special experimental techniques. The thrust-to-weight ratio of aero-engines is increasing due to the improved design of components and the use of innovative materials. Investigations on superalloys, {gamma}-TiAl, and thermal barrier coatings are described in some detail. A discussion of the use of neutron and synchrotron diffraction in automotive applications covers the analysis of surface effects with respect to lubricants and wear, as well as the investigation of microstructure development, deformation, and fatigue behavior of materials, welds and components. Special steels, Al and Mg alloys are discussed and residual stresses in automotive components such as gears or crankshafts are described. Applications of characterization methods on membranes for polymeric membrane fuel cells and on nanocrystalline metal hydrides for hydrogen storage are shown. The degradation of railway tracks after long-term use is taken as an example for the application of synchrotron methods to transport systems beyond the commercial aircraft and light duty passenger car. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  5. Requirements for future automotive batteries - a snapshot

    Science.gov (United States)

    Karden, Eckhard; Shinn, Paul; Bostock, Paul; Cunningham, James; Schoultz, Evan; Kok, Daniel

    Introduction of new fuel economy, performance, safety, and comfort features in future automobiles will bring up many new, power-hungry electrical systems. As a consequence, demands on automotive batteries will grow substantially, e.g. regarding reliability, energy throughput (shallow-cycle life), charge acceptance, and high-rate partial state-of-charge (HRPSOC) operation. As higher voltage levels are mostly not an economically feasible alternative for the short term, the existing 14 V electrical system will have to fulfil these new demands, utilizing advanced 12 V energy storage devices. The well-established lead-acid battery technology is expected to keep playing a key role in this application. Compared to traditional starting-lighting-ignition (SLI) batteries, significant technological progress has been achieved or can be expected, which improve both performance and service life. System integration of the storage device into the vehicle will become increasingly important. Battery monitoring systems (BMS) are expected to become a commodity, penetrating the automotive volume market from both highly equipped premium cars and dedicated fuel-economy vehicles (e.g. stop/start). Battery monitoring systems will allow for more aggressive battery operating strategies, at the same time improving the reliability of the power supply system. Where a single lead-acid battery cannot fulfil the increasing demands, dual-storage systems may form a cost-efficient extension. They consist either of two lead-acid batteries or of a lead-acid battery plus another storage device.

  6. Energy economics of automotive power generation

    Energy Technology Data Exchange (ETDEWEB)

    Tipler, W.

    1975-01-01

    Replacement of 50 percent of the liquid fuels used in static industrial applications by solid fuel would reduce the crude oil offtake by 17 percent; elimination of the demand for high octane gasoline would increase the thermal efficiency of the production of road fuels by 5 percent; replacement of the gasoline engine by diesel or stratified charge engines could reduce the total consumption of automotive fuels by 20 and 10 percent, respectively, and reduce refinery intake by over 25 and 20 percent, respectively; adequate gasoline substitutes can be produced from coal using known technology, but the over-all thermal efficiency of this use of coal is unacceptable because of the 30 to 40 percent efficiency of the fuel production process and the moderate fuel economy of the gasoline engine; replacement of the gasoline engine by the diesel engine could reduce the consumption of coal for automotive purposes by 20 percent and replacement of both by the spark-assisted diesel engine could reduce consumption by 60 percent; the Stirling engine is comparable to the spark-assisted diesel but is bulky and unproven.

  7. Pedestrian recognition using automotive radar sensors

    Science.gov (United States)

    Bartsch, A.; Fitzek, F.; Rasshofer, R. H.

    2012-09-01

    The application of modern series production automotive radar sensors to pedestrian recognition is an important topic in research on future driver assistance systems. The aim of this paper is to understand the potential and limits of such sensors in pedestrian recognition. This knowledge could be used to develop next generation radar sensors with improved pedestrian recognition capabilities. A new raw radar data signal processing algorithm is proposed that allows deep insights into the object classification process. The impact of raw radar data properties can be directly observed in every layer of the classification system by avoiding machine learning and tracking. This gives information on the limiting factors of raw radar data in terms of classification decision making. To accomplish the very challenging distinction between pedestrians and static objects, five significant and stable object features from the spatial distribution and Doppler information are found. Experimental results with data from a 77 GHz automotive radar sensor show that over 95% of pedestrians can be classified correctly under optimal conditions, which is compareable to modern machine learning systems. The impact of the pedestrian's direction of movement, occlusion, antenna beam elevation angle, linear vehicle movement, and other factors are investigated and discussed. The results show that under real life conditions, radar only based pedestrian recognition is limited due to insufficient Doppler frequency and spatial resolution as well as antenna side lobe effects.

  8. Performance evaluation of an automotive thermoelectric generator

    Science.gov (United States)

    Dubitsky, Andrei O.

    Around 40% of the total fuel energy in typical internal combustion engines (ICEs) is rejected to the environment in the form of exhaust gas waste heat. Efficient recovery of this waste heat in automobiles can promise a fuel economy improvement of 5%. The thermal energy can be harvested through thermoelectric generators (TEGs) utilizing the Seebeck effect. In the present work, a versatile test bench has been designed and built in order to simulate conditions found on test vehicles. This allows experimental performance evaluation and model validation of automotive thermoelectric generators. An electrically heated exhaust gas circuit and a circulator based coolant loop enable integrated system testing of hot and cold side heat exchangers, thermoelectric modules (TEMs), and thermal interface materials at various scales. A transient thermal model of the coolant loop was created in order to design a system which can maintain constant coolant temperature under variable heat input. Additionally, as electrical heaters cannot match the transient response of an ICE, modelling was completed in order to design a relaxed exhaust flow and temperature history utilizing the system thermal lag. This profile reduced required heating power and gas flow rates by over 50%. The test bench was used to evaluate a DOE/GM initial prototype automotive TEG and validate analytical performance models. The maximum electrical power generation was found to be 54 W with a thermal conversion efficiency of 1.8%. It has been found that thermal interface management is critical for achieving maximum system performance, with novel designs being considered for further improvement.

  9. Graduate Automotive Technology Education (GATE) Center

    Energy Technology Data Exchange (ETDEWEB)

    Jeffrey Hodgson; David Irick

    2005-09-30

    The Graduate Automotive Technology Education (GATE) Center at the University of Tennessee, Knoxville has completed its sixth year of operation. During this period the Center has involved thirteen GATE Fellows and ten GATE Research Assistants in preparing them to contribute to advanced automotive technologies in the center's focus area: hybrid drive trains and control systems. Eighteen GATE students have graduated, and three have completed their course work requirements. Nine faculty members from three departments in the College of Engineering have been involved in the GATE Center. In addition to the impact that the Center has had on the students and faculty involved, the presence of the center has led to the acquisition of resources that probably would not have been obtained if the GATE Center had not existed. Significant industry interaction such as internships, equipment donations, and support for GATE students has been realized. The value of the total resources brought to the university (including related research contracts) exceeds $4,000,000. Problem areas are discussed in the hope that future activities may benefit from the operation of the current program.

  10. NICKEL AS AN ALTERNATIVE AUTOMOTIVE BODY MATERIAL

    Directory of Open Access Journals (Sweden)

    T. Joseph Sahaya Anand

    2012-06-01

    Full Text Available The study of the thermal, chemical and mechanical properties of pure nickel as an alternative automotive body material is presented in this paper. Current automotive components mainly use steel as the body material. Due to the increasing demand for high performance and related issues, interest is moving towards alternative materials to steel. The hardness values of both heat-treated and non-heat treated pure nickel do not change after annealing; the hardness values are in the range of 118 to 123 HV. As the annealing temperature increases, the ultimate tensile strength, yield strength and Young’s modulus decrease, which indicates that the ductility increases. The highest ultimate tensile strength of pure nickel at 300 °C annealed temperature is 758.78 MPa. X-ray diffraction (XRD studies confirmed pure nickel as a face centred cubic (FCC structure with a lattice constant measured as 0.3492 nm for the unannealed sample, which increases to 0.3512 nm for the annealed samples. The corrosion rate of both annealed and non-heat treated pure nickel is in the range of 0.0266 to 0.048 mm/year.

  11. United States Automotive Materials Partnership LLC (USAMP)

    Energy Technology Data Exchange (ETDEWEB)

    United States Automotive Materials Partnership

    2011-01-31

    The United States Automotive Materials Partnership LLC (USAMP) was formed in 1993 as a partnership between Chrysler Corporation, Ford Motor Company, and General Motors Corporation. Since then the U.S. Department of Energy (DOE) has supported its activities with funding and technical support. The mission of the USAMP is to conduct vehicle-oriented research and development in materials and materials processing to improve the competitiveness of the U.S. Auto Industry. Its specific goals are: (1) To conduct joint research to further the development of lightweight materials for improved automotive fuel economy; and (2) To work with the Federal government to explore opportunities for cooperative programs with the national laboratories, Federal agencies such as the DOE and universities. As a major component of the DOE's Office of FreedomCAR and Vehicle Technologies Program (FCVT) collaboration with the USAMP, the Automotive Lightweighting Materials (ALM) program focuses on the development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. The FCVT was announced in FY 2002 and implemented in FY 2003, as a successor of the Partnership for a New Generation of Vehicles (PNGV), largely addressed under the first Cooperative Agreement. This second USAMP Cooperative Agreement with the DOE has expanded a unique and valuable framework for collaboratively directing industry and government research efforts toward the development of technologies capable of solving important societal problems related to automobile transportation. USAMP efforts are conducted by the domestic automobile manufacturers, in collaboration with materials and manufacturing suppliers, national laboratories, universities, and other technology or trade organizations. These interactions provide a direct route for implementing newly

  12. Bosch automotive electrics and automotive electronics systems and components, networking and hybrid drive

    CERN Document Server

    2014-01-01

    The significance of electrical and electronic systems has increased considerably in the last few years and this trend is set to continue. The characteristics feature of innovative systems is the fact that they can work together in a network. This requires powerful bus systems that the electronic control units can use to exchange information. Networking and the various bus systems used in motor vehicles are the prominent new topic in the 5th edition of the "Automotive Electric, Automotive Electronics" technical manual. The existing chapters have also been updated, so that this new edition brings the reader up to date on the subjects of electrical and electronic systems in the motor vehicle. Content Electrical and electronical systems – Basic principles of networking - Examples of networked vehicles – Bus systems – Architecture of electronic systems – Mechatronics – Elektronics – Electronic control Units – Software – Sensors – Actuators – Hybrid drives – Vehicle electrical system – Start...

  13. Advances in LEDs for automotive applications

    Science.gov (United States)

    Bhardwaj, Jy; Peddada, Rao; Spinger, Benno

    2016-03-01

    High power LEDs were introduced in automotive headlights in 2006-2007, for example as full LED headlights in the Audi R8 or low beam in Lexus. Since then, LED headlighting has become established in premium and volume automotive segments and beginning to enable new compact form factors such as distributed low beam and new functions such as adaptive driving beam. New generations of highly versatile high power LEDs are emerging to meet these application needs. In this paper, we will detail ongoing advances in LED technology that enable revolutionary styling, performance and adaptive control in automotive headlights. As the standards which govern the necessary lumens on the road are well established, increasing luminance enables not only more design freedom but also headlight cost reduction with space and weight saving through more compact optics. Adaptive headlighting is based on LED pixelation and requires high contrast, high luminance, smaller LEDs with high-packing density for pixelated Matrix Lighting sources. Matrix applications require an extremely tight tolerance on not only the X, Y placement accuracy, but also on the Z height of the LEDs given the precision optics used to image the LEDs onto the road. A new generation of chip scale packaged (CSP) LEDs based on Wafer Level Packaging (WLP) have been developed to meet these needs, offering a form factor less than 20% increase over the LED emitter surface footprint. These miniature LEDs are surface mount devices compatible with automated tools for L2 board direct attach (without the need for an interposer or L1 substrate), meeting the high position accuracy as well as the optical and thermal performance. To illustrate the versatility of the CSP LEDs, we will show the results of, firstly, a reflector-based distributed low beam using multiple individual cavities each with only 20mm height and secondly 3x4 to 3x28 Matrix arrays for adaptive full beam. Also a few key trends in rear lighting and impact on LED light

  14. MICROALLOYED STEELS FOR THE AUTOMOTIVE INDUSTRY

    Directory of Open Access Journals (Sweden)

    Debanshu Bhattacharya

    2014-12-01

    Full Text Available Two major drivers for the use of newer steels in the automotive industry are fuel efficiency and increased safety performance. Fuel efficiency is mainly a function of weight of steel parts, which in turn, is controlled by gauge and design. Safety is determined by the energy absorbing capacity of the steel used to make the part. All of these factors are incentives for the U.S. automakers to use both Highly Formable and Advanced High Strength Steels (AHSS to replace the conventional steels used to manufacture automotive parts in the past. AHSS is a general term used to describe various families of steels. The most common AHSS is the dual-phase steel that consists of a ferrite-martensite microstructure. These steels are characterized by high strength, good ductility, low tensile to yield strength ratio and high bake hardenability. Another class of AHSS is the complex-phase or multi-phase steel which has a complex microstructure consisting of various phase constituents and a high yield to tensile strength ratio. Transformation Induced Plasticity (TRIP steels is another class of AHSS steels finding interest among the U.S. automakers. These steels consist of a ferrite-bainite microstructure with significant amount of retained austenite phase and show the highest combination of strength and elongation, so far, among the AHSS in use. High level of energy absorbing capacity combined with a sustained level of high n value up to the limit of uniform elongation as well as high bake hardenability make these steels particularly attractive for safety critical parts and parts needing complex forming. A relatively new class of AHSS is the Quenching and Partitioning (Q&P steels. These steels seem to offer higher ductility than the dual-phase steels of similar strengths or similar ductility as the TRIP steels at higher strengths. Finally, martensitic steels with very high strengths are also in use for certain parts. The most recent initiative in the area of AHSS

  15. Automotive Technology Evolved by Electrical and Electronic Systems

    Science.gov (United States)

    Teratani, Tatsuo; Okuma, Shigeru

    Automotive electrical and electronic systems, e.g. EHV, FCV, future X-By-Wire, have recently been introduced or planned in place of mechanical systems. Drivers are demanding environmental performance (fuel consumption and weight reduction), safety and comfort. For general use of the new technologies, evolution of the automotive technology is required, including energy conversion efficiency improvement, size and weight reduction of components, cost reduction and high reliability. This paper discusses and summarizes the next generation power systems, the future vehicle image, power source combinations, and problems to be solved for development of automotive electronics.

  16. Carbon fiber reinforced thermoplastic composites for future automotive applications

    Science.gov (United States)

    Friedrich, K.

    2016-05-01

    After a brief introduction to polymer composite properties and markets, the state of the art activities in the field of manufacturing of advanced composites for automotive applications are elucidated. These include (a) long fiber reinforced thermoplastics (LFT) for secondary automotive components, and (b) continuous carbon fiber reinforced thermosetting composites for car body applications. It is followed by future possibilities of carbon fiber reinforced thermoplastic composites for e.g. (i) crash elements, (ii) racing car seats, and (iii) production and recycling of automotive fenders.

  17. Hydrogenated nitrile rubber for improved durability of automotive rubber parts

    Energy Technology Data Exchange (ETDEWEB)

    Mirza, J.; Leibbrandt, F.; Thoermer, J.

    1987-01-01

    Rubber articles with improved heat resistance and better performance characteristics are becoming of increasing importance for the automotive industry. A new type of elastomer has therefore been developed based on saturated hydrocarbon backbone - for improved heat resistance - with nitrile side groups providing good resistance to swelling. Some of the typical characteristics of hydrogenated nitrile rubber (HNBR) vulcanizates such as good physical properties pattern at elevated low temperatures dynamic properties, ozone resistance and swelling in automotive fluids are discussed. Potential applications are suggested to improve the performance of various rubber parts used in automotive applications such as high performance seals.

  18. Downsizing assessment of automotive Stirling engines

    Science.gov (United States)

    Knoll, R. H.; Tew, R. C., Jr.; Klann, J. L.

    1983-01-01

    A 67 kW (90 hp) Stirling engine design, sized for use in a 1984 1440 kg (3170 lb) automobile was the focal point for developing automotive Stirling engine technology. Since recent trends are towards lighter vehicles, an assessment was made of the applicability of the Stirling technology being developed for smaller, lower power engines. Using both the Philips scaling laws and a Lewis Research Center (Lewis) Stirling engine performance code, dimensional and performance characteristics were determined for a 26 kW (35 hp) and a 37 kW (50 hp) engine for use in a nominal 907 kg (2000 lb) vehicle. Key engine elements were sized and stressed and mechanical layouts were made to ensure mechanical fit and integrity of the engines. Fuel economy estimates indicated that the Stirling engine would maintain a 30 to 45 percent fuel economy advantage comparable spark ignition and diesel powered vehicles in the 1984 period.

  19. Improvement of Automotive Part Supplier Performance Evaluation

    Science.gov (United States)

    Kongmunee, Chalermkwan; Chutima, Parames

    2016-05-01

    This research investigates the problem of the part supplier performance evaluation in a major Japanese automotive plant in Thailand. Its current evaluation scheme is based on experiences and self-opinion of the evaluators. As a result, many poor performance suppliers are still considered as good suppliers and allow to supply parts to the plant without further improvement obligation. To alleviate this problem, the brainstorming session among stakeholders and evaluators are formally conducted. The result of which is the appropriate evaluation criteria and sub-criteria. The analytical hierarchy process is also used to find suitable weights for each criteria and sub-criteria. The results show that a newly developed evaluation method is significantly better than the previous one in segregating between good and poor suppliers.

  20. Advanced automotive diesel engine system study

    Science.gov (United States)

    1983-01-01

    A conceptual study of an advanced automotive diesel engine is discussed. The engine concept selected for vehicle installation was a supercharged 1.4 liter, 4 cylinder spark assisted diesel of 14:1 compression ratio. A compounding unit consisting of a Lysholm compressor and expander is connected to the engine crankshaft by a belt drive. The inlet air charge is heated by the expander exhaust gas via a heat exchanger. Four levels of technology achievement on the selected engine concept were evaluated, from state-of-the-art to the ideal case. This resulted in the fuel economy increasing from 53.2 mpg to 81.7 mpg, and the 0-60 mph time decreasing from 17.6 seconds to 10.9 seconds.

  1. Multi-channel automotive night vision system

    Science.gov (United States)

    Lu, Gang; Wang, Li-jun; Zhang, Yi

    2013-09-01

    A four-channel automotive night vision system is designed and developed .It is consist of the four active near-infrared cameras and an Mulit-channel image processing display unit,cameras were placed in the automobile front, left, right and rear of the system .The system uses near-infrared laser light source,the laser light beam is collimated, the light source contains a thermoelectric cooler (TEC),It can be synchronized with the camera focusing, also has an automatic light intensity adjustment, and thus can ensure the image quality. The principle of composition of the system is description in detail,on this basis, beam collimation,the LD driving and LD temperature control of near-infrared laser light source,four-channel image processing display are discussed.The system can be used in driver assistance, car BLIS, car parking assist system and car alarm system in day and night.

  2. An Assembly Line Balancing Problem Automotive Cables

    Directory of Open Access Journals (Sweden)

    Triki Hager

    2015-02-01

    Full Text Available In this paper, an Assembly Line Balancing Problem (ALBP is presented in a real-world automotive cables manufacturer company. This company found it necessary to balance its line, since it needs to increase the production rate. In this ALBP, the number of stations is known and the objective is to minimize cycle time where both precedence and zoning constrains must be satisfied. This problem is formulated as a binary linear program (BLP. Since this problem is NP-hard, an innovative Genetic Algorithm (GA is implemented. The full factorial design is used to obtain the better combination GA parameters and a simple convergence experimental study is performed on the stopping criteria to reduce computational time. Comparison of the proposed GA results with CPLEX software shows that, in a reasonable time, the GA generates consistent solutions that are very close to their optimal ones. Therefore, the proposed GA approach is very effective and competitive.

  3. Design of Polymer Coatings in Automotive Engines

    Institute of Scientific and Technical Information of China (English)

    LIAO Han-lin; ZHANG Ga; BORDES Jean-Michel; CHRISTIAN Coddet

    2004-01-01

    Driven by economical and ecological reasons, thermoplastics based coatings were more and more used in automotive engines. Two design concepts, flame spraying and serigraphy PEEK coatings on light metal substrate, were introduced in this paper. The friction and wear behavior of PEEK based coatings were investigated systematically. Coatings with different crystallinities can be obtained when cooling speed is controlled. Among three sprayed coatings considered with different crystallinities, the one with highest crystallinity exhibits best friction and wear behavior under dry sliding condition. Under lubricated sliding condition, however, the amorphous coating gives lower friction coefficient. The micron particles such as SiC,MoS2 and graphite in composite coatings can improve significantly the coating wear resistance and have a impact on coating friction behavior.

  4. Automotive radar - investigation of mutual interference mechanisms

    Science.gov (United States)

    Goppelt, M.; Blöcher, H.-L.; Menzel, W.

    2010-09-01

    In the past mutual interference between automotive radar sensors has not been regarded as a major problem. With an increasing number of such systems, however, this topic is receiving more and more attention. The investigation of mutual interference and countermeasures is therefore one topic of the joint project "Radar on Chip for Cars" (RoCC) funded by the German Federal Ministry of Education and Research (BMBF). RoCC's goal is to pave the way for the development of high-performance, low-cost 79 GHz radar sensors based on Silicon-Germanium (SiGe) Monolithic Microwave Integrated Circuits (MMICs). This paper will present some generic interference scenarios and report on the current status of the analysis of interference mechanisms.

  5. Aero and vibroacoustics of automotive turbochargers

    CERN Document Server

    Nguyen-Schäfer, Hung

    2013-01-01

    Aero and Vibroacoustics of Automotive Turbochargers is a topic involving aspects from the working fields of thermodynamics of turbomachinery, aerodynamics, rotordynamics, and noise propagation computation.   In this broadly interdisciplinary subject, thermodynamics of turbomachinery is used to design the turbocharger and to determine its operating conditions.  Aerodynamics is needed to study the compressor flow dynamics and flow instabilities of rotating stall and surge, which can produce growling and whining-type noises. Rotordynamics is necessary to study rotor unbalance and self-excited oil-whirl instabilities, which lead to whistling and constant tone-type noises in rotating floating oil-film type bearings. For the special case of turbochargers using ball bearings, some high-order harmonic and wear noises also manifest in the rotor operating range. Lastly, noise propagation computation, based on Lighthill’s analogy, is required to investigate airborne noises produced by turbochargers in passenger vehi...

  6. Visual comparison testing of automotive paint simulation

    Science.gov (United States)

    Meyer, Gary; Fan, Hua-Tzu; Seubert, Christopher; Evey, Curtis; Meseth, Jan; Schnackenberg, Ryan

    2015-03-01

    An experiment was performed to determine whether typical industrial automotive color paint comparisons made using real physical samples could also be carried out using a digital simulation displayed on a calibrated color television monitor. A special light booth, designed to facilitate evaluation of the car paint color with reflectance angle, was employed in both the real and virtual color comparisons. Paint samples were measured using a multi-angle spectrophotometer and were simulated using a commercially available software package. Subjects performed the test quicker using the computer graphic simulation, and results indicate that there is only a small difference between the decisions made using the light booth and the computer monitor. This outcome demonstrates the potential of employing simulations to replace some of the time consuming work with real physical samples that still characterizes material appearance work in industry.

  7. Advancing Material Models for Automotive Forming Simulations

    Science.gov (United States)

    Vegter, H.; An, Y.; ten Horn, C. H. L. J.; Atzema, E. H.; Roelofsen, M. E.

    2005-08-01

    Simulations in automotive industry need more advanced material models to achieve highly reliable forming and springback predictions. Conventional material models implemented in the FEM-simulation models are not capable to describe the plastic material behaviour during monotonic strain paths with sufficient accuracy. Recently, ESI and Corus co-operate on the implementation of an advanced material model in the FEM-code PAMSTAMP 2G. This applies to the strain hardening model, the influence of strain rate, and the description of the yield locus in these models. A subsequent challenge is the description of the material after a change of strain path. The use of advanced high strength steels in the automotive industry requires a description of plastic material behaviour of multiphase steels. The simplest variant is dual phase steel consisting of a ferritic and a martensitic phase. Multiphase materials also contain a bainitic phase in addition to the ferritic and martensitic phase. More physical descriptions of strain hardening than simple fitted Ludwik/Nadai curves are necessary. Methods to predict plastic behaviour of single-phase materials use a simple dislocation interaction model based on the formed cells structures only. At Corus, a new method is proposed to predict plastic behaviour of multiphase materials have to take hard phases into account, which deform less easily. The resulting deformation gradients create geometrically necessary dislocations. Additional micro-structural information such as morphology and size of hard phase particles or grains is necessary to derive the strain hardening models for this type of materials. Measurements available from the Numisheet benchmarks allow these models to be validated. At Corus, additional measured values are available from cross-die tests. This laboratory test can attain critical deformations by large variations in blank size and processing conditions. The tests are a powerful tool in optimising forming simulations

  8. Improvements of the Crusher System of Cane Shredder and Its Application%糖厂撕裂机破碎系统的改造及其效果

    Institute of Scientific and Technical Information of China (English)

    谭志雄

    2012-01-01

    针对自动卸蔗输送机卸蔗效果存在的欠缺问题,调整撕裂机动力配置,改造破碎系统,增大处理量和保证甘蔗破碎质量,提高糖分抽出率,在2010/11年榨季取得明显效果,基本实现预期改造目标。%The paper mainly introduces the technology reform on the automatic unloading cane conveyor. By adjusting the cane shredder power and modifying the crushing system, there had been obvious achievement in 2010/11 sugar production campaigns and realized the expected target. This reformed system had been proved to ensure the quality of sugarcane crushing, improve sugar extraction efficiency and increase treatment capacity.

  9. Optimization of wet shaking table process using response surface methodology applied to the separation of copper and aluminum from the fine fraction of shredder ELVs.

    Science.gov (United States)

    Jordão, Helga; Sousa, António Jorge; Carvalho, M Teresa

    2016-02-01

    With the purpose of reducing the waste generated by end-of-life vehicles (ELVs) by enhancing the recovery and recycling of nonferrous metals, an experimental study was conducted with the finest size fraction of nonferrous stream produced at an ELV shredder plant. The aim of this work was to characterize the nonferrous stream and to evaluate the efficiency of a gravity concentration process in separating light and heavy nonferrous metal particles that could be easily integrated in a ELV shredder plant (in this case study the separation explicitly addressed copper and aluminum separation). The characterization of a sample of the 0-10mm particle size fraction showed a mixture of nonferrous metals with a certain degree of impurity due to the present of contaminants such as plastics. The majority of the particles exhibited a wire shape, preventing an efficient separation of materials without prior fragmentation. The gravity concentration process selected for this study was the wet shaking table and three operating parameters of the equipment were manipulated. A full factorial design in combination with a central composite design was employed to model metals recovery. Two second order polynomial equations were successfully fitted to describe the process and predict the recovery of copper and aluminum in Cu concentrate under the conditions of the present study. The optimum conditions were determined to be 11.1° of inclination, 2.8L/min of feed water flow and 4.9L/min of wash water flow. All three final products of the wet shaking table had a content higher than 90% in relation to one of the metals, wherein a Cu concentrate product was obtained with a Cu content of 96%, and 78% of Cu recovery and 2% of Al recovery.

  10. METHOD OF HYDROGEN FEEDING FOR AUTOMOTIVE ENGINE SUPPLY

    Directory of Open Access Journals (Sweden)

    F. Abramchuk

    2010-01-01

    Full Text Available On basis of analysis of various methods of hydrogen feeding for automotive engine supply methods of multipoint hydrogen distribution with microprocessor-based control are proposed.

  11. Conference on Future Automotive Technology Focus Electro Mobility

    CERN Document Server

    2013-01-01

    The increasing trend towards electric cars leads to several challenges for the automobile industry, research institutes and politics as well as for the society. Research and serial development move closer together to meet automotive standards with new components such as traction batteries integrated into hybrid and electrical drivetrains. Furthermore, the influence of e-mobility on the daily mobility behavior, the effects on the automotive supply chain and the impact on industrial production have to be taken into account. According to these complex aspects it is crucial to not only acquire specific knowledge in the particular fields but also to consider their functional interaction. Therefore, it seems essential to merge competence from science, economy and politics. This year, the annual „Conference on Future Automotive Technology“ as the follow-up of the „2. Automobiltechnisches Kolloquium München” focuses on the economical realization of widespread automotive electro mobility. Contents - Energy St...

  12. Springback Compensation Process for High Strength Steel Automotive Parts

    Science.gov (United States)

    Onhon, M. Fatih

    2016-08-01

    This paper is about an advanced stamping simulation methodology used in automotive industry to shorten total die manufacturing times in a new vehicle project by means of benefiting leading edge virtual try-out technology.

  13. THE AUTOMOTIVE INDUSTRY IN A NEW TEHNOLOGICAL ERA

    Directory of Open Access Journals (Sweden)

    Simona Catalina ALBULESCU

    2014-11-01

    Full Text Available The business world is changing at an impressive speed: the global financial crisis, challenging markets, technology and talent crisis have a major impact on business. The last century can be associated with the triumph of the automobile industry. At the beginning of the 21st century the automotive industry has experienced one of the largest shifts in the automotive history. The new CO2 regulations on global level have determined the automotove industry to adopt new and original technologies faster than anticipated. The emerging tendency of car sharing in larger cities added to the media information related to the negative environmental effects of car mobility generate concerns that customers were seeking a replacement to the traditional, individual car ownership. The automotive industry will face challenging years ahead taking into consideration the shifting paradigm in auto-mobility. In this context, this article aims to provide a general perspective of the tendencies in the automotive sector.

  14. Kenaf Fiber Composite in Automotive Industry: An Overview

    Directory of Open Access Journals (Sweden)

    F. Hassan

    2017-02-01

    Full Text Available Recently, natural fibers become an attractive to automotive industry as an alternative reinforcement for glass fiber reinforced thermoplastics. Additionally, natural fiber components in the automotive industry can provide numerous advantages compared to synthetic conventional such as reduction of weight and cost,  recyclability, renewability and in addition to eco-efficiency. Thus, the use of natural fibers in automotive industry has shown increasingly stringent environmental criteria. Furthermore, amongst grouped bast fibers such as flax, hemp, jute, ramie and kenaf; kenaf fiber seen as potential natural fiber with robust mechanical properties. Kenaf fiber had been explored to enhance desired mechanical properties as an automotive structural components. As usual, natural fibres have some issues and disadvantages when used as reinforcements for polymeric composites. Therefore, some modification performed on fibers such as chemical treatment was carried out. In addition, the use of a coupling agent and a plasticizer can also increase fiber-matrix adhesive bonding.

  15. THE AUTOMOTIVE INDUSTRY IN A NEW TEHNOLOGICAL ERA

    Directory of Open Access Journals (Sweden)

    Simona Catalina ALBULESCU

    2014-11-01

    Full Text Available The business world is changing at an impressive speed: the global financial crisis, challenging markets, technology and talent crisis have a major impact on business. The last century can be associated with the triumph of the automobile industry. At the beginning of the 21st century the automotive industry has experienced one of the largest shifts in the automotive history. The new CO2 regulations on global level have determined the automotove industry to adopt new and original technologies faster than anticipated. The emerging tendency of car sharing in larger cities added to the media information related to the negative environmental effects of car mobility generate concerns that customers were seeking a replacement to the traditional, individual car ownership. The automotive industry will face challenging years ahead taking into consideration the shifting paradigm in auto-mobility. In this context, this article aims to provide a general perspective of the tendencies in the automotive sector.

  16. COMPOSITION CHANGES IN REFRIGERANT BLENDS FOR AUTOMOTIVE AIR CONDITIONING

    Science.gov (United States)

    Three refrigerant blends used to replace CFC-12 in automotive air conditioners were evaluated for composition changes due to typical servicing and leakage. When recommended service procedures were followed, changes in blend compositions were relatively small. Small changes in b...

  17. Firm and Product Heterogeneity in China's Automotive Exports

    Directory of Open Access Journals (Sweden)

    Jing Wang

    2015-12-01

    Full Text Available The main purpose of this paper is to provide an in-depth analysis of the anatomy of China's automotive exports, relying on the literature on firm and product heterogeneity. For this purpose, we use highly disaggregated HS 8-digit product-category level data collected by the Chinese Customs Office for 2000 and 2008, and we distinguish between foreign firms, domestic public firms, and domestic private firms. We also decompose automotive products into autos and auto parts and components (P/C. We then calculate both the extensive margins – number of products exported – and intensive margins – average value of exports per product – of China's automotive exports. We estimate gravity equations to assess the determinants of China's exports of autos and auto P/C. Overall, our analysis yields a number of new, interesting stylized facts about China's automotive exports by confirming the need for taking into account different types of heterogeneity in analyzing international trade.

  18. On a learning precedence graph concept for the automotive industry

    OpenAIRE

    Hanne Klindworth; Christian Otto; Armin Scholl

    2010-01-01

    Assembly line balancing problems (ALBP) consist in assigning the total workload for manufacturing a product to stations of an assembly line as typically applied in automotive industry. The distribution of the tasks to the stations is due to restrictions which can be expressed in a precedence graph. However, automotive manufacturers usually do not know complete precedence graphs describing the production processes of their models. Unfortunately, the known approaches for graph generation are no...

  19. Joining Technology of Dissimilar Materials for Automotive Components(Ⅱ)

    Institute of Scientific and Technical Information of China (English)

    Meung Ho Rhee; Jong Ho Song; Woo Young Chung; Young Myoung Kim

    2004-01-01

    Joining techniques of dissimilar materials for lightweight multi-material automotive body structure were discussed. The joining of 1 .4 mm thickness steel and 2 mm thickness of Al were performed by the new method that is hybrid laser welding system. After aluminum and steel were welded by laser hybrid welding process, the micro-structure investment and the micro-hardness test were carried out. Hybrid laser welding promises a bright future in joining technology of dissimilar materials for automotive components.

  20. Meeting the Embedded Design Needs of Automotive Applications

    CERN Document Server

    Lyons, Wayne

    2011-01-01

    The importance of embedded systems in driving innovation in automotive applications continues to grow. Understanding the specific needs of developers targeting this market is also helping to drive innovation in RISC core design. This paper describes how a RISC instruction set architecture has evolved to better meet those needs, and the key implementation features in two very different RISC cores are used to demonstrate the challenges of designing for real-time automotive systems.

  1. THE AUTOMOTIVE INDUSTRY IN A NEW TEHNOLOGICAL ERA

    OpenAIRE

    Simona Catalina ALBULESCU; Anca Alexandra PUCÃREA; Ovidiu DASCÃLU

    2014-01-01

    The business world is changing at an impressive speed: the global financial crisis, challenging markets, technology and talent crisis have a major impact on business. The last century can be associated with the triumph of the automobile industry. At the beginning of the 21st century the automotive industry has experienced one of the largest shifts in the automotive history. The new CO2 regulations on global level have determined the automotove industry to adopt new and original technologies f...

  2. The impact of alternate fuels on future candidate automotive engines

    Energy Technology Data Exchange (ETDEWEB)

    Rahnke, C.J.; Nichols, R.J.

    1982-06-01

    The thermal efficiency that could occur in the future for a variety of automotive engine candidates operating on conventional and alternate fuels is projected based on current automotive engine development trends and the special characteristics of the various alternate fuels. The multi-fuel engine candidates include mixture cycle and direct injection reciprocating engines, as well as adiabatic turbocompound engines and advanced gas turbine and Stirling engines. The alternate fuels considered are propane, methanol, ethanol, diesel and methane.

  3. Applicability valuation for evaluation of surface deflection in automotive outer panels

    Directory of Open Access Journals (Sweden)

    D.H. Park

    2008-12-01

    Full Text Available Purpose: Upon unloading in a forming process there is elastic recovery, which is the release of the elasticstrains and the redistribution of the residual stresses through the thickness direction, thus producing surfacedeflection. It causes changes in shape and dimensions that can create major problem in the external appearanceof outer panels. Thus surface deflection prediction is an important issue in sheet metal forming industry. Manyfactors could affect surface deflection in the process, such as material variations in mechanical properties, sheetthickness, tool geometry, processing parameters and lubricant condition.Design/methodology/approach: Numerical simulation of process was performed by the use of finite elementmethod, paying attention particularly to the thickness distribution and surface deflection of the drawn outerpanel and the outline flange during forming. Simulation procedures of automotive outer panel as large size shapeare as follows; 1 Acquisition of drawing parts 2 Laser scanning for generating CAD model 3 CAD modelgeneration 4 Simulation model operation 5 Simulation execution and analyses of simulation results.Findings: The development of automation in stamping and assembly processes of automobile manufacture willrequire an excellent surface quality of formed panels and also their accurate dimensions.Practical implications: The use of high strength steel sheets in the manufacturing of automobile outer panels hasincreased in the automotive industry over the years because of its lightweight and fuel-efficient improvement.But one of the major concerns of stamping is surface deflection in the formed outer panels. Hence, to be costeffective, accurate prediction must be made of its formability. The automotive industry places rigid constraintson final shape and dimensional tolerances as well as external appearance quality of outer panels. The numericalsimulation makes it possible to design and optimize the total process to a level

  4. Comparative Analysis of Domestic FSY-3 the US 71854 Branch Shredders%国产FSY-30与美国71854枝丫粉碎机的对比分析

    Institute of Scientific and Technical Information of China (English)

    吴兆迁; 牛晓华; 王晓军; 樊涛; 王德柱; 刘洋; 曲振兴

    2012-01-01

    The US 71854 Tree Branch Shredder has advanced technical performance,suitable for the production operation in mountain woodlands where tree branches are shredded and processed on the spot;domestic FSY-30 Tree Branch Shredder features simple structure,convenient maintenance and lost construction cost.Though.FSY-30 Tree Branch Shredder is interior to US 71854 Tree Branch Shredder by 13.2% in terms of production capacity,its fuel consumption has reduced by 13.6%,operating cost has reduced by 30.6%,equipment price has reduced by 73.3% and material bulk density has increased by 8.9%.The machine has excellent comprehensive technical and economic characteristics and complies to the actual situation of China,suitable for mountain woodland branch shredding and recycling operations.%美国71854型林木枝丫粉碎机的技术性能较为先进,适用于山场林地林木枝丫粉碎并就地处理的生产作业;国产FSY-30型林木枝丫粉碎机结构简单,维护方便,制造成本低。虽然国产FSY-30型林木枝丫粉碎机生产能力比美国71854型林木枝丫粉碎机降低13.2%,但其燃油消耗量降低13.6%,作业成本降低30.6%,设备售价降低73.3%,堆料容重提高8.9%。该机综合技术经济性能较好,符合我国国情,适用于山场林地林木枝丫粉碎并进行回收利用的生产作业。

  5. Mechanized recovery of olive pruning residues: ash contamination and harvesting losses

    Directory of Open Access Journals (Sweden)

    A. Assirelli

    2013-09-01

    Full Text Available Agricultural residues represent an important source of biomass for energy. Among the available biomass suitable for energy and available in Italy, pruning represents about the 20% of the total. About 1.184 million of hectares are planted with olive trees; the pruning residues coming from these plantations represent a wide source of biomass at National level. The authors tested six commercial pruning harvesters to determine harvesting losses and product contamination when recovering pruning residues. All harvesters used a mechanical pick-up to collect the residues and a shredder to reduce them into chips. Three different pick-up settings were tested and namely: 1 cm above ground level, manufacturer’s specification and 3 cm above ground level. Ash content in the shredded material was taken as a measure of contamination: the uncontaminated branch material collected directly from the trees had a value of 3.5%, whereas in shredded residues varied between 4.5% and over 5.5%, for the shortest and the longest distance between the pick-up and the soil surface, respectively. Harvesting losses were slightly, but significantly, related to pick-up setting, and mainly depended on machine type. Both machines have shown a good quality of the work performed and the results obtained indicates that the work phases could be simplified in order to reduce both the time of use and the harvesting costs.

  6. 78 FR 48467 - Delphi Automotive Systems, LLC, Products and Service Solutions Division, Including On-Site Leased...

    Science.gov (United States)

    2013-08-08

    ... Employment and Training Administration Delphi Automotive Systems, LLC, Products and Service Solutions... workers of Delphi Automotive Systems, LLC, Product and Service Solutions Division, Original Equipment... of ] Delphi Automotive Systems, LLC, Product and Service Solutions Division, including on-site...

  7. Automotive Catalyst State Diagnosis Using Microwaves

    Directory of Open Access Journals (Sweden)

    Moos Ralf

    2015-01-01

    Full Text Available The state of catalysts plays a key role in automotive exhaust gas aftertreatment. The soot or ash loading of Diesel particulate filters, the oxygen loading degree in three-way catalysts, the amount of stored ammonia in SCR catalysts, or the NOx loading degree in NOx storage catalysts are important parameters that are today determined indirectly and in a model-based manner with gas sensors installed upstream and/or downstream of the catalysts. This contribution gives an overview on a novel approach to determine the catalyst state directly by a microwave-based technique. The method exploits the fact that the catalyst housing acts as a microwave cavity resonator. As “sensing” elements, one or two simple antennas are mounted inside the catalyst canning. The electrical properties of the catalyst device (ceramic honeycomb plus coating and storage material can be measured. Preferably, the resonance characteristics, e.g., the resonance frequencies, of selected cavity modes are observed. The information on the catalyst interior obtained in such a contactless manner is very well correlated with the catalyst state as will be demonstrated for different exhaust gas aftertreatment systems.

  8. DYNAMIC TASK SCHEDULING ON MULTICORE AUTOMOTIVE ECUS

    Directory of Open Access Journals (Sweden)

    Geetishree Mishra

    2014-12-01

    Full Text Available Automobile manufacturers are controlled by stringent govt. regulations for safety and fuel emissions and motivated towards adding more advanced features and sophisticated applications to the existing electronic system. Ever increasing customer’s demands for high level of comfort also necessitate providing even more sophistication in vehicle electronics system. All these, directly make the vehicle software system more complex and computationally more intensive. In turn, this demands very high computational capability of the microprocessor used in electronic control unit (ECU. In this regard, multicore processors have already been implemented in some of the task rigorous ECUs like, power train, image processing and infotainment. To achieve greater performance from these multicore processors, parallelized ECU software needs to be efficiently scheduled by the underlaying operating system for execution to utilize all the computational cores to the maximum extent possible and meet the real time constraint. In this paper, we propose a dynamic task scheduler for multicore engine control ECU that provides maximum CPU utilization, minimized preemption overhead, minimum average waiting time and all the tasks meet their real time deadlines while compared to the static priority scheduling suggested by Automotive Open Systems Architecture (AUTOSAR

  9. Light source modeling for automotive lighting devices

    Science.gov (United States)

    Zerhau-Dreihoefer, Harald; Haack, Uwe; Weber, Thomas; Wendt, Dierk

    2002-08-01

    Automotive lighting devices generally have to meet high standards. For example to avoid discomfort glare for the oncoming traffic, luminous intensities of a low beam headlight must decrease by more than one order of magnitude within a fraction of a degree along the horizontal cutoff-line. At the same time, a comfortable homogeneous illumination of the road requires slowly varying luminous intensities below the cutoff line. All this has to be realized taking into account both, the legal requirements and the customer's stylistic specifications. In order to be able to simulate and optimize devices with a good optical performance different light source models are required. In the early stage of e.g. reflector development simple unstructured models allow a very fast development of the reflectors shape. On the other hand the final simulation of a complex headlamp or signal light requires a sophisticated model of the spectral luminance. In addition to theoretical models based on the light source's geometry, measured luminance data can also be used in the simulation and optimization process.

  10. Vibration reduction on automotive shafts using piezoceramics

    Science.gov (United States)

    Kunze, Holger; Riedel, Mathias; Schmidt, Knut; Bianchini, Emanuele

    2003-08-01

    This paper reports an experimental study on active vibration reduction for automotive shafts with the use of piezoelectric material. The work focuses on an axle of an Audi A2. The demand in the automobile sector for higher comfort in the vehicle is of a great importance alongside the requirements of lighter weight and low fuel consumption. These requirements are typically in conflict with each other. One solution is the use of intelligent materials instead of viscoelastic materials and proof mass absorbers. These solutions are quite heavy especially at low frequencies. Active vibration control and piezoelectric devices are advantageous in this application due to their low mass to performance ratio. Our research study explores the use of such piezoelectric devices for an axle. In conjunction with electronics it will reduce vibrations in the first natural bending mode of the axle. Laboratory tests simulated the condition present in the road. At first a stationary set up was used, then a simulated disturbance was input at the attachment points of the shaft. Finally, a test with rotating shaft was performed. Piezoelectric devices (custom QuickPacks from ACX, a Division of Cymer) were used as sensors and as actuators to properly control the axle during the different operating conditions. The power consumption of each actuator pair was less than 20W. The work described here details the test setup, the control strategy, the hardware implementation as well as the test results obtained.

  11. Advanced high strength steels for automotive industry

    Directory of Open Access Journals (Sweden)

    Galán, J.

    2012-04-01

    Full Text Available The car industry is facing pressure because of the growing demand for more fuel-efficient passenger cars. In order to limit energy consumption and air pollution the weight of the carbody has to be reduced. At the same time, high levels of safety have to be guaranteed. In this situation, the choice of material becomes a key decision in car design. As a response to the requirements of the automotive sector, high strength steels and advanced high strength steels have been developed by the steel industry. These modern steel grades offer an excellent balance of low cost, light weight and mechanical properties.

    La industria del automóvil se enfrenta a una creciente demanda de vehículos de pasajeros más eficientes. Con el fin de disminuir el consumo de energía y la contaminación ambiental, el peso del vehículo tiene que ser reducido, al mismo tiempo que se garantizan altos niveles de seguridad. Ante esta situación, la elección de material se convierte en una decisión crucial en el diseño del vehículo. Como respuesta a las necesidades del sector automovilístico, nuevos aceros avanzados y de alta resistencia, han sido desarrollados por la industria siderúrgica. Dichos tipos de acero ofrecen un excelente equilibrio de precio, peso y propiedades mecánicas.

  12. Remanufacturing in automotive industry: Challenges and limitations

    Directory of Open Access Journals (Sweden)

    Paulina Golinska

    2011-10-01

    Full Text Available Purpose: The aim of this paper is to provide the framework for management of reverse flow of materials in automotive industry. The emphasis is placed on the remanufacturing activities. Materials management in such conditions is a real challenge. The cause for this is parallel use of raw materials and reused materials. Such hybrid flows of materials are characterized by increased level of uncertainty connected with amount, quality and timing. Design/methodology/approach: This paper presents a comprehensive review of remanufacturing and traditional manufacturing. The stabilization of reverse flows is crucial for continuity of remanufacturing operations. The simulation model and results are discussed regarding stabilization of the reverse flows. Findings: Authors identify main problems that appear in the area of combining at the production system forward and reverse flows of materials. The agent-based technology is applied for configuration and stabilization of reverse network. Research limitations/implications: Paper is case – oriented. Practical implications: Both logistician and IT researchers might benefit from authors approach. Originality/value: Authors provide an interdisciplinary approach combining operations management, logistics and information technology.

  13. Flywheel Energy Storage for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Magnus Hedlund

    2015-09-01

    Full Text Available A review of flywheel energy storage technology was made, with a special focus on the progress in automotive applications. We found that there are at least 26 university research groups and 27 companies contributing to flywheel technology development. Flywheels are seen to excel in high-power applications, placing them closer in functionality to supercapacitors than to batteries. Examples of flywheels optimized for vehicular applications were found with a specific power of 5.5 kW/kg and a specific energy of 3.5 Wh/kg. Another flywheel system had 3.15 kW/kg and 6.4 Wh/kg, which can be compared to a state-of-the-art supercapacitor vehicular system with 1.7 kW/kg and 2.3 Wh/kg, respectively. Flywheel energy storage is reaching maturity, with 500 flywheel power buffer systems being deployed for London buses (resulting in fuel savings of over 20%, 400 flywheels in operation for grid frequency regulation and many hundreds more installed for uninterruptible power supply (UPS applications. The industry estimates the mass-production cost of a specific consumer-car flywheel system to be 2000 USD. For regular cars, this system has been shown to save 35% fuel in the U.S. Federal Test Procedure (FTP drive cycle.

  14. Dynamic Task Scheduling on Multicore Automotive ECUs

    Directory of Open Access Journals (Sweden)

    Geetishree Mishra

    2014-12-01

    Full Text Available Automobile manufacturers are controlled by stringen t govt. regulations for safety and fuel emissions a nd motivated towards adding more advanced features and sophisticated applications to the existing electro nic system. Ever increasing customer’s demands for high level of comfort also necessitate providing even m ore sophistication in vehicle electronics system. All t hese, directly make the vehicle software system mor e complex and computationally more intensive. In turn , this demands very high computational capability o f the microprocessor used in electronic control unit (ECU. In this regard, multicore processors have already been implemented in some of the task rigoro us ECUs like, power train, image processing and infotainment. To achieve greater performance from t hese multicore processors, parallelized ECU softwar e needs to be efficiently scheduled by the underlayin g operating system for execution to utilize all the computational cores to the maximum extent possible and meet the real time constraint. In this paper, w e propose a dynamic task scheduler for multicore engi ne control ECU that provides maximum CPU utilization, minimized preemption overhead, minimum average waiting time and all the tasks meet their real time deadlines while compared to the static pr iority scheduling suggested by Automotive Open Syst ems Architecture (AUTOSAR.

  15. Measuring soot particles from automotive exhaust emissions

    Science.gov (United States)

    Andres, Hanspeter; Lüönd, Felix; Schlatter, Jürg; Auderset, Kevin; Jordan-Gerkens, Anke; Nowak, Andreas; Ebert, Volker; Buhr, Egbert; Klein, Tobias; Tuch, Thomas; Wiedensohler, Alfred; Mamakos, Athanasios; Riccobono, Francesco; Discher, Kai; Högström, Richard; Yli-Ojanperä, Jaakko; Quincey, Paul

    2014-08-01

    The European Metrology Research Programme participating countries and the European Union jointly fund a three year project to address the need of the automotive industry for a metrological sound base for exhaust measurements. The collaborative work on particle emissions involves five European National Metrology Institutes, the Tampere University of Technology, the Joint Research Centre for Energy and Transport and the Leibniz Institute for Tropospheric Research. On one hand, a particle number and size standard for soot particles is aimed for. Eventually this will allow the partners to provide accurate and comparable calibrations of measurement instruments for the type approval of Euro 5b and Euro 6 vehicles. Calibration aerosols of combustion particles, silver and graphite proof partially suitable. Yet, a consensus choice together with instrument manufactures is pending as the aerosol choice considerably affects the number concentration measurement. Furthermore, the consortium issued consistent requirements for novel measuring instruments foreseen to replace today's opacimeters in regulatory periodic emission controls of soot and compared them with European legislative requirements. Four partners are conducting a metrological validation of prototype measurement instruments. The novel instruments base on light scattering, electrical, ionisation chamber and diffusion charging sensors and will be tested at low and high particle concentrations. Results shall allow manufacturers to further improve their instruments to comply with legal requirements.

  16. Measuring soot particles from automotive exhaust emissions

    Directory of Open Access Journals (Sweden)

    Andres Hanspeter

    2014-01-01

    Full Text Available The European Metrology Research Programme participating countries and the European Union jointly fund a three year project to address the need of the automotive industry for a metrological sound base for exhaust measurements. The collaborative work on particle emissions involves five European National Metrology Institutes, the Tampere University of Technology, the Joint Research Centre for Energy and Transport and the Leibniz Institute for Tropospheric Research. On one hand, a particle number and size standard for soot particles is aimed for. Eventually this will allow the partners to provide accurate and comparable calibrations of measurement instruments for the type approval of Euro 5b and Euro 6 vehicles. Calibration aerosols of combustion particles, silver and graphite proof partially suitable. Yet, a consensus choice together with instrument manufactures is pending as the aerosol choice considerably affects the number concentration measurement. Furthermore, the consortium issued consistent requirements for novel measuring instruments foreseen to replace today’s opacimeters in regulatory periodic emission controls of soot and compared them with European legislative requirements. Four partners are conducting a metrological validation of prototype measurement instruments. The novel instruments base on light scattering, electrical, ionisation chamber and diffusion charging sensors and will be tested at low and high particle concentrations. Results shall allow manufacturers to further improve their instruments to comply with legal requirements.

  17. Future automotive materials: Evolution or revolution

    Science.gov (United States)

    Beardmore, P.

    1990-01-01

    An exciting era is evolving in the application of new materials technologies to automotive applications. The desire on the part of the automobile industry to completely satisfy the customers while concurrently meeting increasing demands and regulations for stringent emission control and fuel efficiency is opening a plethora of opportunities for new materials. In many cases, materials solutions are the only mechanisms for resolving some of the upcoming issues. The materials scientist and engineer will therefore have a primary role to play and will assume a position of significance hithertofore unseen in the automobile industry. The nature of the industry dictates that changes are primarily evolutionary with respect to chronology but nevertheless some of the future material changes will be revolutionary in nature. This presentation will treat three primary systems of the vehicle separately, based on the different materials approaches which will be adopted. These areas are: (1) skin panels, (2) structures, and (3) powertrains. The competition between a variety of new materials in these 3 systems will be discussed in detail with the various tradeoffs being outlined. Amongst the more prominent of the new breed of materials will be new steel technologies, structural plastics (FRP), aluminum alloys (conventional and rapidly solidified), titanium alloys, metal matrix composites and smart materials (electrorheological fluids, etc.). The pace of development and application is accelerating rapidly and the impetus is likely to increase.

  18. Deployment of ERP Systems at Automotive Industries, Security Inspection (Case Study: IRAN KHODRO Automotive Company)

    Science.gov (United States)

    Ali, Hatamirad; Hasan, Mehrjerdi

    Automotive industry and car production process is one of the most complex and large-scale production processes. Today, information technology (IT) and ERP systems incorporates a large portion of production processes. Without any integrated systems such as ERP, the production and supply chain processes will be tangled. The ERP systems, that are last generation of MRP systems, make produce and sale processes of these industries easier and this is the major factor of development of these industries anyhow. Today many of large-scale companies are developing and deploying the ERP systems. The ERP systems facilitate many of organization processes and make organization to increase efficiency. The security is a very important part of the ERP strategy at the organization, Security at the ERP systems, because of integrity and extensive, is more important of local and legacy systems. Disregarding of this point can play a giant role at success or failure of this kind of systems. The IRANKHODRO is the biggest automotive factory in the Middle East with an annual production over 600.000 cars. This paper presents ERP security deployment experience at the "IRANKHODRO Company". Recently, by launching ERP systems, it moved a big step toward more developments.

  19. Forest feedstocks : systems for recovery of residual biomass

    Energy Technology Data Exchange (ETDEWEB)

    MacDonald, J. [FP Innovations, Vancouver, BC (Canada). FERIC Div.

    2007-07-01

    Interest in forest feedstock is growing due to high energy costs, the need for energy self-sufficiency and climate change issues. The Mountain Pine Beetle (MPB) epidemic in British Columbia has also contributed to the growing interest in forest feedstock. This presentation discussed the potential for wood to be used for liquid fuels conversion, pellets and biorefineries. The extraction of energy from residue biomass was reviewed with reference to traditional sources such as hog fuel and black liquor, as well as new sources that consider the changing landscape. These include harvest residues, MPB-killed stands, burned stands, non-merchantable stands, and stumps. Early thinning and FireSmart treatments were outlined along with the value of purpose-grown energy plantations. The variety of available recovery methods and equipment was demonstrated, including whole-tree chippers; disc and drum chippers; grinders and shredders; overhead conveyor systems; blower attachments; and, wheel-mounted equipment. The performance of each method and equipment was reviewed along with challenges regarding the transportation of a low-value, low bulk-density material over long distances. Although residue bundlers have been developed, it was suggested that it may be more cost effective to convert the feedstock in the field using a mobile biorefinery, and then transport the denser fuel. It was shown that although a range of equipment is available, nothing has been designed specifically for full-tree residue. It was noted that coordination with conventional harvesting is desirable, but may not be possible in all cases. Lessons from studies have indicated that the distance from the mill is a major cost factor and that the debris should be prepared in advance to shipping. tabs., figs.

  20. Novel synthesis and applications of Thiomer solidification for heavy metals immobilization in hazardous ASR/ISW thermal residue.

    Science.gov (United States)

    Baek, Jin Woong; Mallampati, Srinivasa Reddy; Park, Hung Suck

    2016-03-01

    The present paper reports the novel synthesis and application of Thiomer solidification for heavy metal immobilization in hazardous automobile shredder residues and industrial solid waste (ASR/ISW) thermal residues. The word Thiomer is a combination of the prefix of a sulfur-containing compound "Thio" and the suffix of "Polymer" meaning a large molecule compound of many repeated subunits. To immobilize heavy metals, either ASR/ISW thermal residues (including bottom and fly ash) was mixed well with Thiomer and heated at 140°C. After Thiomer solidification, approximately 91-100% heavy metal immobilization was achieved. The morphology and mineral phases of the Thiomer-solidified ASR/ISW thermal residue were characterized by field emission-scanning electron microscopy, energy dispersive X-ray spectroscopy and X-ray diffraction (XRD), which indicated that the amounts of heavy metals detectable on the ASR/ISW thermal residue surface decreased and the sulfur mass percent increased. XRD indicated that the main fraction of the enclosed/bound materials on the ASR/ISW residue contained sulfur associated crystalline complexes. The Thiomer solidified process could convert the heavy metal compounds into highly insoluble metal sulfides and simultaneously encapsulate the ASR/ISW thermal residue. These results show that the proposed method can be applied to the immobilization of ASR/ISW hazardous ash involving heavy metals. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Residual stress analysis of drive shafts after induction hardening

    Energy Technology Data Exchange (ETDEWEB)

    Lemos, Guilherme Vieira Braga; Rocha, Alexandre da Silva; Nunes, Rafael Menezes, E-mail: lemos_gl@yahoo.com.br [Universidade Federal do Rio Grande do Sul (UFRS), Porto Algre, RS (Brazil); Hirsch, Thomas Karl [Stiftung Institut für Werkstofftechnik (IWT), Bremen (Germany)

    2014-08-15

    Typically, for automotive shafts, shape distortion manifests itself in most cases after the induction hardening by an effect known as bending. The distortion results in a boost of costs, especially due to machining parts in the hardened state to fabricate its final tolerances. In the present study, residual stress measurements were carried out on automotive drive shafts made of DIN 38B3 steel. The samples were selected in consequence of their different distortion properties by an industrial manufacturing line. One tested shaft was straightened, because of the considerable dimensional variation and the other one not. Firstly, the residual stress measurements were carried out by using a portable diffractometer, in order to avoid cutting the shafts and evaluate the original state of the stresses, and afterwards a more detailed analysis was realized by a conventional stationary diffractometer. The obtained results presented an overview of the surface residual stress profiles after induction hardening and displayed the influence of the straightening process on the redistribution of residual stresses. They also indicated that the effects of the straightening in the residual stresses cannot be neglected. (author)

  2. Developing e-learning solutions in the automotive industry

    Directory of Open Access Journals (Sweden)

    Razvan Virgil Bogdan

    2016-07-01

    Full Text Available In the rapid developing market of automotive industry, cutting-edge technologies are being introduced. One such example is the AUTOSAR standard. Companies are investing a large amount of finances for the training of their employees into the intricacies of such technologies. In order to face such an increase of the training costs, automotive corporation have started lately switching their approach to e-Learning systems. This paper presents an e-Learning approach developed in the automotive industry in order to address the demands of teaching AUTOSAR standard. The developed e-Learning project is called Academy. In order to develop the e-Learning solution we focused on the Software Development part of automotive industry. Therefore we had to gather the ideas from different trainers, come with a common approach and use specific techniques so that the trainee should get a real feeling of the material. It is presented the design, implementation and evaluation of this e-Learning solution, but more than that faced issues and learned lessons. Developing this solution has offered different insights into how to approach such a task which are useful for the further expansion of the project, but also for future researchers who might encounter such a challenge of developing e-Learning solutions for the automotive industry. These are all grouped in a set of guidelines related to following a model of implementation, getting track of participants, user interaction with the AUTOSAR standard, test and production development and so on.

  3. Automotive Mg Research and Development in North America

    Energy Technology Data Exchange (ETDEWEB)

    Carpenter, Joseph A. [U.S. Department of Energy; Jackman, Jennifer [CANMET - Materials Technology Laboratory, Natural Resources of Canada; Li, Naiyi [Ford Motor Company; Osborne, Richard J. [General Motors Corporation; Powell, Bob R. [General Motors Corporation; Sklad, Philip S [ORNL

    2006-01-01

    Expanding world economic prosperity and probable peaking of conventional petroleum production in the coming decades require efforts to increase the efficiency of, and the development of alternatives to, petroleum-based fuels used in automotive transportation. North America has been aggressively pursuing both approaches for over ten years. Mainly as a result of lower prices due to global sourcing, magnesium has recently emerged as a serious candidate for lightweighting, and thus increasing the fuel efficiency of, automotive transportation. Automotive vehicles produced in North America currently use more Mg than vehicles produced elsewhere in the world, but the amounts per vehicle are very small in comparison to other materials such as steel, aluminum and plastics. The reasons, besides price, are primarily a less-developed state of technology for Mg in automotive transportation applications and lack of familiarity by the vehicle manufacturers with the material. This paper reviews some publicly-known, recent, present and future North American research and development activities in Mg for automotive applications.

  4. Numerical and Experimental Applications of TWIP Steel in Automotive Parts

    Science.gov (United States)

    Lee, J. W.; Lim, J. H.; Choi, J. B.; Oh, P. Y.

    2011-08-01

    Modern automotive design has been faced with the weight reduction problem to meet the CO2 emissions standard while achieving high safety and compact design. Such being the case, most car makers want to use the ultra high strength steels (UHSS). But there are several problems when such steels are used, due to presumed lack of formability. Since the disadvantage such as above, it has been suggested that UHSS need special forming methods or it should be used only limited process like simple bending, by many automotive research institutes. To overcome these shortcomings, Twinning Induced Plasticity (TWIP) steel for improved strength and formability has been developed by steel making company, including POSCO, Korea. Because of its characteristics, it is expected to be widely used in automotive parts. This paper aims at finding out several ways how to make effective use of TWIP steel in automotive parts. Especially, comprising about from 15 to 18% manganese and from 1.5 to 2% aluminum which was developed by POSCO for application of the automotive parts will be considered.

  5. Overview of Automotive Core Tools: Applications and Benefits

    Science.gov (United States)

    Doshi, Jigar A.; Desai, Darshak

    2017-08-01

    Continuous improvement of product and process quality is always challenging and creative task in today's era of globalization. Various quality tools are available and used for the same. Some of them are successful and few of them are not. Considering the complexity in the continuous quality improvement (CQI) process various new techniques are being introduced by the industries, as well as proposed by researchers and academia. Lean Manufacturing, Six Sigma, Lean Six Sigma is some of the techniques. In recent years, there are new tools being opted by the industry, especially automotive, called as Automotive Core Tools (ACT). The intention of this paper is to review the applications and benefits along with existing research on Automotive Core Tools with special emphasis on continuous quality improvement. The methodology uses an extensive review of literature through reputed publications—journals, conference proceedings, research thesis, etc. This paper provides an overview of ACT, its enablers, and exertions, how it evolved into sophisticated methodologies and benefits used in organisations. It should be of value to practitioners of Automotive Core Tools and to academics who are interested in how CQI can be achieved using ACT. It needs to be stressed here that this paper is not intended to scorn Automotive Core Tools, rather, its purpose is limited only to provide a balance on the prevailing positive views toward ACT.

  6. Evolution of the Automotive Body Coating Process—A Review

    Directory of Open Access Journals (Sweden)

    Nelson K. Akafuah

    2016-06-01

    Full Text Available Automotive coatings and the processes used to coat automobile surfaces exemplify the avant-garde of technologies that are capable of producing durable surfaces, exceeding customers’ expectations of appearance, maximizing efficiency, and meeting environmental regulations. These accomplishments are rooted in 100 years of experience, trial-and-error approaches, technique and technology advancements, and theoretical assessments. Because of advancements directed at understanding the how, why, when, and where of automobile coatings, the progress in controlling droplets and their deposition attributes, and the development of new technologies and paint chemistries, a comprehensive and up-to-date review of automobile coatings and coating technologies was considered to be of value to industrial practitioners and researchers. Overall, the critical performance factors driving the development and use of advanced automotive coatings and coating technologies are (a aesthetic characteristics; (b corrosion protection; (c mass production; (d cost and environmental requirements; and (e appearance and durability. Although the relative importance of each of these factors is debatable, the perfection of any one at the expense of another would be unacceptable. Hence, new developments in automotive coatings are described and discussed in the following review, and then related to improvements in production technologies and paints. Modern automotive coating procedures are also discussed in detail. Finally, an extrapolation into the future of automotive coating is offered with a view of the developments and technologies needed for an increasingly efficient and more sustainable coatings industry.

  7. Overview of Automotive Core Tools: Applications and Benefits

    Science.gov (United States)

    Doshi, Jigar A.; Desai, Darshak

    2016-06-01

    Continuous improvement of product and process quality is always challenging and creative task in today's era of globalization. Various quality tools are available and used for the same. Some of them are successful and few of them are not. Considering the complexity in the continuous quality improvement (CQI) process various new techniques are being introduced by the industries, as well as proposed by researchers and academia. Lean Manufacturing, Six Sigma, Lean Six Sigma is some of the techniques. In recent years, there are new tools being opted by the industry, especially automotive, called as Automotive Core Tools (ACT). The intention of this paper is to review the applications and benefits along with existing research on Automotive Core Tools with special emphasis on continuous quality improvement. The methodology uses an extensive review of literature through reputed publications—journals, conference proceedings, research thesis, etc. This paper provides an overview of ACT, its enablers, and exertions, how it evolved into sophisticated methodologies and benefits used in organisations. It should be of value to practitioners of Automotive Core Tools and to academics who are interested in how CQI can be achieved using ACT. It needs to be stressed here that this paper is not intended to scorn Automotive Core Tools, rather, its purpose is limited only to provide a balance on the prevailing positive views toward ACT.

  8. Change management methodologies trained for automotive infotainment projects

    Science.gov (United States)

    Prostean, G.; Volker, S.; Hutanu, A.

    2017-01-01

    An Automotive Electronic Control Units (ECU) development project embedded within a car Environment is constantly under attack of a continuous flow of modifications of specifications throughout the life cycle. Root causes for those modifications are for instance simply software or hardware implementation errors or requirement changes to satisfy the forthcoming demands of the market to ensure the later commercial success. It is unavoidable that from the very beginning until the end of the project “requirement changes” will “expose” the agreed objectives defined by contract specifications, which are product features, budget, schedule and quality. The key discussions will focus upon an automotive radio-navigation (infotainment) unit, which challenges aftermarket devises such as smart phones. This competition stresses especially current used automotive development processes, which are fit into a 4 Year car development (introduction) cycle against a one-year update cycle of a smart phone. The research will focus the investigation of possible impacts of changes during all phases of the project: the Concept-Validation, Development and Debugging-Phase. Building a thorough understanding of prospective threats is of paramount importance in order to establish the adequate project management process to handle requirement changes. Personal automotive development experiences and Literature review of change- and configuration management software development methodologies led the authors to new conceptual models, which integrates into the structure of traditional development models used in automotive projects, more concretely of radio-navigation projects.

  9. Advanced Automotive Technologies annual report to Congress, fiscal year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This annual report serves to inform the United States Congress on the progress for fiscal year 1996 of programs under the Department of Energy`s Office of Advanced Automotive Technologies (OAAT). This document complies with the legislative requirement to report on the implementation of Title III of the Automotive Propulsion Research and Development Act of 1978. Also reported are related activities performed under subsequent relevant legislation without specific reporting requirements. Furthermore, this report serves as a vital means of communication from the Department to all public and private sector participants. Specific requirements that are addressed in this report are: Discussion of how each research and development contract, grant, or project funded under the authority of this Act satisfies the requirements of each subsection; Current comprehensive program definition for implementing Title III; Evaluation of the state of automotive propulsion system research and development in the United States; Number and amount of contracts and grants awarded under Title III; Analysis of the progress made in developing advanced automotive propulsion system technology; and Suggestions for improvements in automotive propulsion system research and development, including recommendations for legislation.

  10. 77 FR 13350 - Certain Automotive GPS Navigation Systems, Components Thereof, and Products Containing Same...

    Science.gov (United States)

    2012-03-06

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Certain Automotive GPS Navigation Systems, Components Thereof, and Products Containing Same... importation of certain automotive GPS navigation systems, components thereof, and products containing the...

  11. Investigation of metallurgical coatings for automotive applications

    Science.gov (United States)

    Su, Jun Feng

    Metallurgical coatings have been widely used in the automotive industry from component machining, engine daily running to body decoration due to their high hardness, wear resistance, corrosion resistance and low friction coefficient. With high demands in energy saving, weight reduction and limiting environmental impact, the use of new materials such as light Aluminum/magnesium alloys with high strength-weight ratio for engine block and advanced high-strength steel (AHSS) with better performance in crash energy management for die stamping, are increasing. However, challenges are emerging when these new materials are applied such as the wear of the relative soft light alloys and machining tools for hard AHSS. The protective metallurgical coatings are the best option to profit from these new materials' advantages without altering largely in mass production equipments, machinery, tools and human labor. In this dissertation, a plasma electrolytic oxidation (PEO) coating processing on aluminum alloys was introduced in engine cylinder bores to resist wear and corrosion. The tribological behavior of the PEO coatings under boundary and starve lubrication conditions was studied experimentally and numerically for the first time. Experimental results of the PEO coating demonstrated prominent wear resistance and low friction, taking into account the extreme working conditions. The numerical elastohydrodynamic lubrication (EHL) and asperity contact based tribological study also showed a promising approach on designing low friction and high wear resistant PEO coatings. Other than the fabrication of the new coatings, a novel coating evaluation methodology, namely, inclined impact sliding tester was presented in the second part of this dissertation. This methodology has been developed and applied in testing and analyzing physical vapor deposition (PVD)/ chemical vapor deposition (CVD)/PEO coatings. Failure mechanisms of these common metallurgical hard coatings were systematically

  12. Materials Challenges for Automotive PEM Fuel Cells

    Science.gov (United States)

    Gasteiger, Hubert

    2004-03-01

    Over the past few years, significant R efforts aimed at meeting the challenging cost and performance targets required for the use of Polymer Electrolyte Membrane (PEM) fuel cells in automotive applications. Besides engineering advances in bipolar plate materials and design, the optimization of membrane-electrode assemblies (MEAs) was an important enabler in reducing the cost and performance gaps towards commercial viability for the automotive market. On the one hand, platinum loadings were reduced from several mgPt/cm2MEA [1] to values of 0.5-0.6 mgPt/cm2MEA in current applications and loadings as low as 0.25 mgPt/cm2MEA have been demonstrated on the research level [2]. On the other hand, implementation of thin membranes (20-30 micrometer) [3, 4] as well as improvements in diffusion medium materials, essentially doubled the achievable power density of MEAs to ca. 0.9 W/cm2MEA (at 0.65 V) [5], thereby not only reducing the size of a PEMFC fuel cell system, but also reducing its overall materials cost (controlled to a large extent by membrane and Pt-catalyst cost). While this demonstrated a clear path towards automotive applications, a renewed focus of R efforts is now required to develop materials and fundamental materials understanding to assure long-term durability of PEM fuel cells. This presentation therefore will discuss the state-of-the-art knowledge of catalyst, catalyst-support, and membrane degradation mechanisms. In the area of Pt-catalysts, experience with phosphoric acid fuel cells (PAFCs) has shown that platinum sintering leads to long-term performance losses [6]. While this is less critical at the lower PEMFC operating temperatures (200C), very little is known about the dependence of Pt-sintering on temperature, cell voltage, and catalyst type (i.e., Pt versus Pt-alloys) and will be discussed here. Similarly, carbon-support corrosion can contribute significantly to voltage degradation in PAFCs [7], and even in the PEMFC environment more corrosion

  13. Low-Density Steels: Complex Metallurgy for Automotive Applications

    Science.gov (United States)

    Zuazo, I.; Hallstedt, B.; Lindahl, B.; Selleby, M.; Soler, M.; Etienne, A.; Perlade, A.; Hasenpouth, D.; Massardier-Jourdan, V.; Cazottes, S.; Kleber, X.

    2014-09-01

    The current aim in the development of third-generation steels for lightweighting automotive applications is to increase strength keeping at least the same formability as current steel concepts. In this philosophy, an optimal concept would be one that brings, in addition, a lower density. For this purpose, low-density steels have been designed with important aluminum additions obtaining density reductions of 8-10% or higher in comparison with low-carbon steels. At the levels required for lightweighting, aluminum introduces complex phenomena in steels. Here, some of the effects of aluminum in phase stability, CALPHAD-type modeling, and microstructure development are described, the latter in relation with mechanical properties. Finally, the potential of two families of lightweight steels for automotive applications is assessed by comparison with a steel currently present in automotive structures.

  14. Hybrid Modeling and Simulation of Automotive Supply Chain Network

    Directory of Open Access Journals (Sweden)

    Wen Wang

    2013-07-01

    Full Text Available According to the operation of automotive supply chain and the features of various simulation methods, we create and simulate a automotive supply chain network model with the core enterprise of two vehicle manufacturers, consisting of several parts suppliers, vehicle distributors and logistics service providers. On this basis of a conceptual model including the establishment of enterprise layer, business layer and operation layer, we establish a detailed model of the network system according to the network structure of automotive supply chain, the operation process and the internal business process of core enterprises; then we use System Dynamics (SD, Discrete Event Simulation (DES and Agent Based Modeling (ABM to describe the operating state of each node in the network model. We execute and analyze the simulation model of the whole network system described by Anylogic, using the results of the distributors’ inventory, inventory cost and customer’s satisfaction to prove the effectiveness of the model.

  15. Social media for knowledge sharing in automotive repair

    CERN Document Server

    Finkbeiner, Patric

    2017-01-01

    This book explores, describes and explains the predictors essential for the acceptance of social media as a digital platform to share professional knowledge in the field of automotive repair in Germany. It reports a rigorous literature review covering key elements of social media, knowledge management and technology acceptance studies. The book assumes a pragmatist approach and applies mixed methods in an exploratory sequential design, combining qualitative and quantitative methods to ensure robust collection and analysis of the collected data. Based on a survey on German automotive repair shops, the author provides a framework, for various stakeholders, to comprehend the motivations for knowledge sharing for automotive repair professionals in Germany. This book not only adds to the existing academic body of knowledge but also provides implications for industry and legislation on a European scale. .

  16. Offshoring trends in the manufacturing process within the automotive industry

    DEFF Research Database (Denmark)

    Simplay, S.; Hansen, Zaza Nadja Lee

    2014-01-01

    This paper investigates offshoring trends in the automotive industry. The research approach consisted of combining empirical findings from case companies with latest research from the field. Empirical data was collected through case studies from 15 automotive organisations based in Europe...... consisting of original equipment manufacturers and engineering service providers. The findings indicated some offshoring trends in the automotive industry. Offshoring in this industry is moving from a manufacturing focus to incorporate large parts of the process, including high-level product development...... engineering activities. This development has created several challenges. These challenges arose as organisations are not considering how offshoring activities could be integrated with an increasingly global supply chain for the manufacturing of the final product. The paper contributes to manufacturing theory...

  17. State of the art: benchmarking microprocessors for embedded automotive applications

    Directory of Open Access Journals (Sweden)

    Adnan Shaout

    2016-09-01

    Full Text Available Benchmarking microprocessors provides a way for consumers to evaluate the performance of the processors. This is done by using either synthetic or real world applications. There are a number of benchmarks that exist today to assist consumers in evaluating the vast number of microprocessors that are available in the market. In this paper an investigation of the various benchmarks available for evaluating microprocessors for embedded automotive applications will be performed. We will provide an overview of the following benchmarks: Whetstone, Dhrystone, Linpack, standard performance evaluation corporation (SPEC CPU2006, embedded microprocessor benchmark consortium (EEMBC AutoBench and MiBench. A comparison of existing benchmarks will be given based on relevant characteristics of automotive applications which will give the proper recommendation when benchmarking processors for automotive applications.

  18. Digitalization of automotive industry – scenarios for future manufacturing

    Directory of Open Access Journals (Sweden)

    Peters Steven

    2016-01-01

    Full Text Available Among the current challenges to the global automotive industry are changes in global markets leading to product variety, regulation leading to pressure for new technologies in body and powertrain, and competition by new players such as huge information and communication technology companies. Automotive original equipment manufacturers (OEMs deal with these issues in different ways. This paper uses the scenario technique to illustrate possible answers to the question, how future value chains of automotive industry will look like. In almost all cases, information and communication technology (ICT plays a major role in future strategies to cope with the aforementioned challenges. On the one hand, ICT can boost the way to more efficient production of variants by utilizing smart manufacturing approaches, on the other hand ICT enables new features such as autonomous driving.

  19. Making aerospace technology work for the automotive industry - Introduction

    Science.gov (United States)

    Olson, W. T.

    1978-01-01

    In many cases it has been found that advances made in one technical field can contribute to other fields. An investigation is in this connection conducted concerning subjects from contemporary NASA programs and projects which might have relevance and potential usefulness to the automotive industry. Examples regarding aerospace developments which have been utilized by the automotive industry are related to electronic design, computer systems, quality control experience, a NASA combustion scanner and television display, exhaust gas analyzers, and a device for suppressing noise propagated through ducts. Projects undertaken by NASA's center for propulsion and power research are examined with respect to their value for the automotive industry. As a result of some of these projects, a gas turbine engine and a Stirling engine might each become a possible alternative to the conventional spark ignition engine.

  20. Sustainable supply chain management practices in Indian automotive industry

    DEFF Research Database (Denmark)

    Mathivathanan, Deepak; Kannan, Devika; Haq, A. Noorul

    2017-01-01

    managerial, environmental, societal, and governmental associations. We propose a framework model, using the Decision Making Trial and Evaluation Laboratory method, to evaluate automotive industry SSCM practices specifically situated in the emerging economy of India. Through a questionnaire survey......As one of the largest manufacturing sectors, the automotive industry has a deep impact on the society and environment. Automotive products provide mobility to millions and create jobs, but also threaten the environment. Consumer pressure, government regulations, and stakeholder demands...... into the traditional supply chain and that help an industry shift towards a sustainable supply chain are called SSCM practices. Firms have difficulty identifying the most useful practices and learning how these practices impact each other. Unfortunately, no existing research has studied the interrelated influences...

  1. Efficient production of automotive biofuels; Effektiv produktion av biodrivmedel

    Energy Technology Data Exchange (ETDEWEB)

    Gode, Jenny; Hagberg, Linus; Rydberg, Tomas; Raadberg, Henrik; Saernholm, Erik

    2008-07-01

    The report describes opportunities and consequences associated with biomass polygeneration plants, in particular the role that heat plants (HP) or combined heat and power plants (CHP) in district heating systems can play in the production of automotive biofuels. The aim of the report is to provide a knowledge base to stakeholders to help assess energy and environmental benefits associated with collaborative approaches in planning, constructing and operating energy plants. Several configurations are possible for an energy polygeneration plant, but this report focuses on configurations in which a plant for automotive biofuel production and a district heating system with HPs or CHPs have been integrated in some way in order to achieve added value. The modes of integration are several, e.g.: - Supply of process steam from the CHP to the fuel plant, by which the time of operation for the CHP can be extended; Supply of surplus heat from the fuel plant to the district heating system; Material exchange between the systems, by use of residue streams from the fuel plant as fuel in the HP/CHP; Surplus heat from the fuel plant used for drying of the solid fuel to the HP/CHP or for drying of raw material for pellets production; Co-location providing opportunities for shared infrastructure for raw material handling, service systems, utilities and/or logistics. The report principally addresses integration options of the first three types, but describes briefly also pellets production. The starting point for the analysis of integration options is the description of technologies of interest for the production of automotive biofuels. Commercially available technologies are of prime interest, but also a couple of technologies under development are included in this part of the study. In addition to outlining the process characteristics for these processes, surrounding conditions and system requirements are briefly outlined. The results are summarized in Table S1. Ethanol fermentation

  2. Beyond survival: Challenges facing South African automotive component exporters

    Directory of Open Access Journals (Sweden)

    M. J. Naude

    2006-12-01

    Full Text Available Purpose and Objective: The South African automotive component industry faces huge challenges in a very competitive global market. The primary focus of this research article is to determine the challenges facing exporters within this industry with special reference to selected sub-sectors. The challenges are approached from a supply chain perspective only. Problem Investigated: The research problem of this study was to identify these unique challenges and ascertain whether the implementation of a 'philosophy of continuous improvement' could be used as a strategic tool to address the challenges they face in the market. Methodology: This study included a combination of literature review, interviews with managers in the selected sub-groups and questionnaires sent out to determine the challenges facing automotive component exporters. In order to test the content validity and the reliability of the questionnaire, a pilot study was conducted at two organisations that are the main suppliers of automotive filters for passenger vehicles. The non-probability convenience sample technique was used to select the sample and consisted of selected sub-sectors that contribute 64,1% of the total value of automotive component exports in South Africa. Out of twenty-seven questionnaires sent out, twenty (74% response rate were duly completed by the respondents and returned to the researcher. Findings: South Africa faces unique challenges and these are listed and ranked according to priority from most to least important as follows: 1. The reduction of production costs; 2. R/US$ exchange rate effect on the respondent's export sales and profit margin; 3. Exchange rate fluctuations; 4. Threats to the local automotive component market; and 5. Increased competition by way of manufactured imports being sold in the South African market. Value of Research: The study provides recommendations that can be used within the automotive component industry.

  3. A Study of the Awareness Level of Electric Vehicle Technology in California Community College Automotive Curriculums.

    Science.gov (United States)

    Keyzer, James

    California automotive technician programs were surveyed regarding their awareness of the impact that mandates of the Clean Air Act would have on their automotive technology programs. A questionnaire was sent to 100 California community colleges with an automotive technology program; 49 usable questionnaires were returned. A possible byproduct of…

  4. Visualization of the air flow behind the automotive benchmark vent

    Science.gov (United States)

    Pech, Ondrej; Jedelsky, Jan; Caletka, Petr; Jicha, Miroslav

    2015-05-01

    Passenger comfort in cars depends on appropriate function of the cabin HVAC system. A great attention is therefore paid to the effective function of automotive vents and proper formation of the flow behind the ventilation outlet. The article deals with the visualization of air flow from the automotive benchmark vent. The visualization was made for two different shapes of the inlet channel connected to the benchmark vent. The smoke visualization with the laser knife was used. The influence of the shape of the inlet channel to the airflow direction, its enlargement and position of air flow axis were investigated.

  5. Financial Crises and Automotive Industry Development in Southeast Asia

    DEFF Research Database (Denmark)

    Doner, Richard F.; Wad, Peter

    2014-01-01

    The automotive industries of Southeast Asia have grown significantly but unevenly. Thailand has outperformed its neighbours in Malaysia, Indonesia and the Philippines with regard to production and, most notably, export volumes. But the Thai auto industry has not exhibited the level of local...... whose very success weakened pressures for upgrading; encouraged more moderate automotive liberalisation in Indonesia and, to a lesser extent, in the Philippines; but promoted only minimal changes to Malaysia’s relatively protectionist national car strategy. The fact that the crises served more...... to reinforce than to reverse existing tendencies reflects a broader set of political economy factors that influence national perceptions of crises severity and alternative responses....

  6. DOE Automotive Composite Materials Research: Present and Future Efforts

    Energy Technology Data Exchange (ETDEWEB)

    Warren, C.D.

    1999-08-10

    One method of increasing automotive energy efficiency is through mass reduction of structural components by the incorporation of composite materials. Significant use of glass reinforced polymers as structural components could yield a 20--30% reduction in vehicle weight while the use of carbon fiber reinforced materials could yield a 40--60% reduction in mass. Specific areas of research for lightweighting automotive components are listed, along with research needs for each of these categories: (1) low mass metals; (2) polymer composites; and (3) ceramic materials.

  7. NEW TRENDS AND CHELLENGES IN AUTOMOTIVE INDUSTRY LOGISTICS OPERATIONS

    Directory of Open Access Journals (Sweden)

    Dušan Sabadka

    2015-03-01

    Full Text Available This paper lays out the main features of the global automotive industry and identifies several important trends. Logistics operations (inbound and outbound in the automotive supply chain are complex and account for large expenses and therefore are segments in the value chainwhere improvements can be made. Better coordination between inbound and outbound logistics contributes to optimising the supply chains, to reducing inventories and to responding to consumer requests. As economies grow, the competition shifts towards brand image and customisation and here the speed and reliability of logistics operations becomes a critical elements.

  8. Engineering wear-resistant surfaces in automotive aluminum

    Science.gov (United States)

    Kavorkijan, V.

    2003-02-01

    Inadequate wear resistance and low seizure loads prevent the direct use of aluminum alloys in automotive parts subject to intensive friction combined with high thermal and mechanical loading, such as brake discs, pistons, and cylinder liners. To enable the use of aluminum alloys in the production of automotive brake discs and other wear-resistant products, the insertion of a monolithic friction cladding rather than surface coating has been considered in this work. Three experimental approaches, two based on the pressure-less infiltration of porous ceramic preforms and one based on the subsequent hot rolling of aluminum and metal-matrix composite strips, are currently under investigation.

  9. Visualization of the air flow behind the automotive benchmark vent

    Directory of Open Access Journals (Sweden)

    Pech Ondrej

    2015-01-01

    Full Text Available Passenger comfort in cars depends on appropriate function of the cabin HVAC system. A great attention is therefore paid to the effective function of automotive vents and proper formation of the flow behind the ventilation outlet. The article deals with the visualization of air flow from the automotive benchmark vent. The visualization was made for two different shapes of the inlet channel connected to the benchmark vent. The smoke visualization with the laser knife was used. The influence of the shape of the inlet channel to the airflow direction, its enlargement and position of air flow axis were investigated.

  10. Producing lower-cost titanium for automotive applications

    Science.gov (United States)

    Hartman, A. D.; Gerdemann, S. J.; Hansen, J. S.

    1998-09-01

    Although titanium has attractive properties that can improve the performance and economy of automobiles, at its current cost, it cannot compete with steel in most applications for which it is suited. It is readily apparent that titanium cannot be considered a viable mass-market automotive materials alternative as long as it is produced with the Kroll process. A look at existing and new technologies (as well as some that have been found lacking) in terms of applicability toward high-volume, low-cost titanium production for automotive applications indicates other options.

  11. Utilization of Durability Criterion to Develop Automotive Components

    DEFF Research Database (Denmark)

    Ricardo, Luiz Carlos Hernandes

    2010-01-01

    . This paper will present a review of the techniques used in the automotive industry regarding durability before mentioned systems. The paper will present the procedures to obtain the spectrum loading to use in finite element analysis and the validation in laboratory and proving grounds.......Today the automotive companies must reduce the time to development of new products with improvement in performance, durability and low cost reductions where possible. To achieve this goal the carmakers need to improve the design criterion of car systems like body, chassis and suspension components...

  12. Study on Safety Design of Garden Shredders%园艺碎枝机的安全性设计研究

    Institute of Scientific and Technical Information of China (English)

    张明

    2011-01-01

    通过任务分析法对用户使用碎枝机过程进行分解,分析了现有产品在使用各环节中存在的安全隐患。论述了园艺碎枝机的安全性涉及功能安全、操作安全、心理安全以及环境安全4个方面,并依据奥卡姆剃刀原理和设计中的包容原则等理论,提出了精简设计提升功能安全,包容设计增强操作安全,多感官体验设计完善心理安全,以及低碳设计致力于环境安全的解决方法。%Through decomposition of the process to use garden shredder by the ways of task,it analyzed the security risks in the link for products.It also discussed four aspects of security including the functional safety,operational safety,psychological security and environmental security.It proposed streamlining the design to enhance the security,inclusive design to enhance the safe operation and other two solutions according to the Occam's Razor principle,inclusiveness principle etc.

  13. Sliding mode observers for automotive alternator

    Science.gov (United States)

    Chen, De-Shiou

    Estimator development for synchronous rectification of the automotive alternator is a desirable approach for estimating alternator's back electromotive forces (EMFs) without a direct mechanical sensor of the rotor position. Recent theoretical studies show that estimation of the back EMF may be observed based on system's phase current model by sensing electrical variables (AC phase currents and DC bus voltage) of the synchronous rectifier. Observer design of the back EMF estimation has been developed for constant engine speed. In this work, we are interested in nonlinear observer design of the back EMF estimation for the real case of variable engine speed. Initial back EMF estimate can be obtained from a first-order sliding mode observer (SMO) based on the phase current model. A fourth-order nonlinear asymptotic observer (NAO), complemented by the dynamics of the back EMF with time-varying frequency and amplitude, is then incorporated into the observer design for chattering reduction. Since the cost of required phase current sensors may be prohibitive, the most applicable approach in real implementation by measuring DC current of the synchronous rectifier is carried out in the dissertation. It is shown that the DC link current consists of sequential "windows" with partial information of the phase currents, hence, the cascaded NAO is responsible not only for the purpose of chattering reduction but also for necessarily accomplishing the process of estimation. Stability analyses of the proposed estimators are considered for most linear and time-varying cases. The stability of the NAO without speed information is substantiated by both numerical and experimental results. Prospective estimation algorithms for the case of battery current measurements are investigated. Theoretical study indicates that the convergence of the proposed LAO may be provided by high gain inputs. Since the order of the LAO/NAO for the battery current case is one order higher than that of the link

  14. The Partnership for Today That Works for Tomorrow: The Professional Automotive Training Center at Shoreline Community College.

    Science.gov (United States)

    Hightower, Cameron

    The Professional Automotive Training Center (PATC) is a 28,150 square foot automotive technician training center located on the campus of Shoreline Community College (SCC) in Washington. The complex is the result of a partnership between SCC and the 230 automotive dealerships of the Puget Sound Automotive Dealers Association and is designed to…

  15. Support and promoter effects in automotive exhaust catalysis

    NARCIS (Netherlands)

    Lepage, M.

    2009-01-01

    Automotive catalysis being a mature technology, it can only be improved by the introduction of new breakthroughs. The ideas generating these technical advances in material science can be found thanks to the synthesis and study of model systems with controlled geometries, compositions, interactions a

  16. AUTOMOTIVE AND HEAVY-DUTY ENGINE COOLANT RECYCLING BY DISTILLATION

    Science.gov (United States)

    This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling automotive and heavy-duty engine coolants for a facility such as the New Jersey Department of Transportation garage in Ewing, New Jersey. he specific recycling evaluated is b...

  17. EVALUATION OF FILTRATION AND DISTILLATION METHODS FOR RECYCLING AUTOMOTIVE COOLANT.

    Science.gov (United States)

    This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling automotive and heavy-duty engine coolants at a New Jersey Department of Transportation garage. The specific recycling units evaluated are based on the technologies of filtrat...

  18. Environmental Performance and firm strategies in the Dutch automotive sector

    NARCIS (Netherlands)

    van der Vooren, A.; Alkemade, F.; Hekkert, M.P.

    2013-01-01

    This paper explores how automotive firms positioned their portfolio since the introduction of energy labels for cars. Using data on product characteristics of automobiles offered on the Dutch market over the period 2001-2010, we analyse how car manufacturers' product portfolios have changed. Portfol

  19. Dow Corning photonics: the silicon advantage in automotive photonics

    Science.gov (United States)

    Clapp, Terry V.; Paquet, Rene; Norris, Ann; Pettersen, Babette

    2005-02-01

    The Automotive Market offers several opportunities for Dow Corning to leverage the power of silicon-based materials. Dow Corning Photonics Solutions has a number of developments that may be attractive for the emergent photonics needs in automobiles, building on 40 years of experience as a leading Automotive supplier with a strong foundation of expertise and an extensive product offering- from encapsulents and highly reliable resins, adhesives, insulating materials and other products, ensuring that the advantage of silicones are already well-embedded in Automotive systems, modules and components. The recent development of LED encapsulants of exceptional clarity and stability has extended the potential for Dow Corning"s strength in Photonics to be deployed "in-car". Demonstration of board-level and back-plane solutions utilising siloxane waveguide technology offers new opportunities for systems designers to integrate optical components at low cost on diverse substrates. Coupled with work on simple waveguide technology for sensors and data communications applications this suite of materials and technology offerings is very potent in this sector. The harsh environment under hood and the very extreme thermal range that materials must sustain in vehicles due to both their engine and the climate is an applications specification that defines the siloxane advantage. For these passive optics applications the siloxanes very high clarity at the data-communications wavelengths coupled with extraordinary stability offers significant design advantage. The future development of Head-Up-Displays for instrumentation and data display will offer yet more opportunities to the siloxanes in Automotive Photonics.

  20. Laser surface treatment of grey cast iron for automotive applications

    NARCIS (Netherlands)

    Ocelik, V.; Tang, P.N.; de Boer, M.C.; de Oliveira, U.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

    2005-01-01

    The surface of pearlitic grey cast iron was treated using a 2 kW Nd:YAG laser beam with the final aim to improve its surface properties, mainly for automotive applications. Two kinds of laser surface treatments were experimentally applied. In the laser surface hardening approach the surface of cast

  1. Ozone biomonitoring in a local network around an automotive plant

    Energy Technology Data Exchange (ETDEWEB)

    Kostka-Rick, R. [Biologisch Ueberwachen und Bewerten, Echterdingen (Germany)

    2002-07-01

    Effects of ambient air pollution by organic solvents, emitted from coating processes, are monitored by sensitive bioindicator plants since 1992 in and around a large automotive plant. In order to distinguish specific injury symptoms caused by these solvents, typical leaf injury symptoms by oxidant air pollution are also recorded. (orig.)

  2. GATE Center for Automotive Fuel Cell Systems at Virginia Tech

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, Douglas [Virginia Polytechnic Inst. and State Univ. (Virginia Tech), Blacksburg, VA (United States)

    2011-09-30

    The Virginia Tech GATE Center for Automotive Fuel Cell Systems (CAFCS) achieved the following objectives in support of the domestic automotive industry: Expanded and updated fuel cell and vehicle technologies education programs; Conducted industry directed research in three thrust areas development and characterization of materials for PEM fuel cells; performance and durability modeling for PEM fuel cells; and fuel cell systems design and optimization, including hybrid and plug-in hybrid fuel cell vehicles; Developed MS and Ph.D. engineers and scientists who are pursuing careers related to fuel cells and automotive applications; Published research results that provide industry with new knowledge which contributes to the advancement of fuel cell and vehicle systems commercialization. With support from the Dept. of Energy, the CAFCS upgraded existing graduate course offerings; introduced a hands-on laboratory component that make use of Virginia Tech's comprehensive laboratory facilities, funded 15 GATE Fellowships over a five year period; and expanded our program of industry interaction to improve student awareness of challenges and opportunities in the automotive industry. GATE Center graduate students have a state-of-the-art research experience preparing them for a career to contribute to the advancement fuel cell and vehicle technologies.

  3. Automotive HMI design and participatory user involvement: review and perspectives.

    Science.gov (United States)

    François, Mathilde; Osiurak, François; Fort, Alexandra; Crave, Philippe; Navarro, Jordan

    2017-04-01

    Automotive human-machine interface (HMI) design is facing new challenges due to the technological advances of the last decades. The design process has to be adapted in order to address human factors and road safety challenges. It is now widely accepted that user involvement in the HMI design process is valuable. However, the current form of user involvement in industry remains at the stages of concept assessment and usability tests. Moreover, the literature in other fields (e.g. information systems) promotes a broader user involvement with participatory design (i.e. the user is fully involved in the development process). This article reviews the established benefits of participatory design and reveals perspectives for automotive HMI quality improvement in a cognitive ergonomic framework. Practitioner Summary: Automotive HMI quality determines, in part, drivers' ability to perform primary driving tasks while using in-vehicle devices. User involvement in the design process is a key point to contribute to HMI quality. This article reports the potential benefits of a broad involvement from drivers to meet automotive HMI design challenges.

  4. Laser surface treatment of grey cast iron for automotive applications

    NARCIS (Netherlands)

    Ocelik, V.; Tang, P.N.; de Boer, M.C.; de Oliveira, U.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

    2005-01-01

    The surface of pearlitic grey cast iron was treated using a 2 kW Nd:YAG laser beam with the final aim to improve its surface properties, mainly for automotive applications. Two kinds of laser surface treatments were experimentally applied. In the laser surface hardening approach the surface of cast

  5. The Progressive Insurance Automotive X PRIZE Education Program

    Energy Technology Data Exchange (ETDEWEB)

    Robyn Ready

    2011-12-31

    The Progressive Insurance Automotive X PRIZE Education Program conducted education and outreach activities and used the competition's technical goals and vehicle demonstrations as a means of attracting students and the public to learn more about advanced vehicle technologies, energy efficiency, climate change, alternative fuels, and the science and math behind efficient vehicle development. The Progressive Insurance Automotive X PRIZE Education Program comprised three integrated components that were designed to educate the general public and create a multi-tiered initiative to engage students and showcase the 21st century skills students will need to compete in our global economy: teamwork, creativity, strong literacy, math and science skills, and innovative thinking. The elements included an Online Experience, a National Student Contest, and in person education events and activites. The project leveraged online connections, strategic partnerships, in-classroom, and beyond-the-classroom initiatives, as well as mainstream media. This education program supported by the U.S. Department of Energy (DOE) also funded the specification of vehicle telemetry and the full development and operation of an interactive online experience that allowed internet users to follow the Progressive Insurance Automotive X PRIZE vehicles as they performed in real-time during the Progressive Insurance Automotive X PRIZE competition events.

  6. Marketing and Distributive Education Curriculum Guide in Automotive and Petroleum.

    Science.gov (United States)

    Harris, E. Edward; And Others

    This curriculum guide is designed to provide the curriculum coordinator with a basis for planning a comprehensive program in the field of marketing. It also provides marketing and distributive education teachers with maximum flexibility in planning an automotive and petroleum curriculum. The essential common and specialized competencies are…

  7. Model update and variability assessment for automotive crash simulations

    NARCIS (Netherlands)

    Sun, J.; He, J.; Vlahopoulos, N.; Ast, P. van

    2007-01-01

    In order to develop confidence in numerical models which are used for automotive crash simulations, results are often compared with test data, and in some cases the numerical models are adjusted in order to improve the correlation. Comparisons between the time history of acceleration responses from

  8. Success Story of Radar Technology in Automotive Applications

    Science.gov (United States)

    Meinecke, Marc-Michael; Jerhot, Jiři

    2012-05-01

    The radar technology has a long history of over more than one century. In contrast to this its application in the automotive domain is a quite young activity. The enablers of this relatively new research field are presented in this article from a car manufacturers perspective covering aspects of signal processing algorithms, hardware and driver assistance applications.

  9. Energy autonomous sensor systems for automotive condition monitoring

    Energy Technology Data Exchange (ETDEWEB)

    Fraeulin, Christian [A. RAYMOND GmbH und Co. KG, Weil am Rhein (Germany); Nurnus, Joachim; Punt, Wladimir [Micropelt GmbH, Freiburg (Germany)

    2011-07-01

    With the number of automotive sensors increasing, the effort for connecting all these sensors becomes more and more of an issue. A possible way to overcome these issues is to use energy-autonomous sensors that, besides the basic sensor function, include means to transmit the measurement data wirelessly as well as to generate the electrical energy they need to operate. Generating the electrical energy can be done by harvesting energy from ambient sources that are available in abundance, among others these can be heat and vibration. Although these principles are not new, so far little attempts have been made to incorporate these technologies into cost-sensitive segments like the automotive market. In this paper we present two energy-autonomous sensor demonstrators for automotive applications: a temperature sensor powered with a thermoelectric harvester, thus using a tiny amount of the physical property it wants to measure, and a pressure sensor powered by vibration energy. For both applications, managing the limited amount of available energy is one of the mayor tasks in developing this kind of systems. Therefore both systems use special means in hard- and software to cope with that task. While the automotive market is a very interesting one for energy-autonomous sensors, many other possible applications can be considered, among them the solar market and industrial condition monitoring. (orig.)

  10. Automotive body panel containing thermally exfoliated graphite oxide

    Science.gov (United States)

    Prud'Homme, Robert K. (Inventor); Aksay, Ilhan A. (Inventor); Adamson, Douglas (Inventor); Abdala, Ahmed (Inventor)

    2011-01-01

    An automotive body panel containing a polymer composite formed of at least one polymer and a modified graphite oxide material, which is a thermally exfoliated graphite oxide with a surface area of from about 300 m.sup.2/g to 2600 m.sup.2/g.

  11. Training Needs for High Performance in the Automotive Industry.

    Science.gov (United States)

    Clyne, Barry; And Others

    A project was conducted in Australia to identify the training needs of the emerging industry required to support the development of the high performance areas of the automotive machining and reconditioning field especially as it pertained to auto racing. Data were gathered through a literature search, interviews with experts in the field, and…

  12. Compensating springback in the automotive practice using MASHAL

    NARCIS (Netherlands)

    Ohnimus, S.; Petzoldt, M.; Rietman, B.; Weiher, J.

    2005-01-01

    New materials are used in the automotive industry to reduce weight and to improve crash performance. These materials feature a higher ratio of yield stress to elastic modulus leading to increased springback after tool release. The resulting shape deviations and their efficient reduction is of major

  13. Flexible Labour Strategy in the Dutch Automotive Industry

    NARCIS (Netherlands)

    Riemsdijk, van Maarten; Leede, de Jan

    2001-01-01

    Labour flexibility is a major way for companies to become more flexible. Why companies use flexible labour relations varies widely per industry. We assess the development of labour flexibility within the Dutch automotive industry. Four cases, together representing the production chain, are presented

  14. EVALUATION OF FILTRATION AND DISTILLATION METHODS FOR RECYCLING AUTOMOTIVE COOLANT.

    Science.gov (United States)

    This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling automotive and heavy-duty engine coolants at a New Jersey Department of Transportation garage. The specific recycling units evaluated are based on the technologies of filtrat...

  15. AUTOMOTIVE AND HEAVY-DUTY ENGINE COOLANT RECYCLING BY DISTILLATION

    Science.gov (United States)

    This evaluation addresses the product quality, waste reduction, and economic issues involved in recycling automotive and heavy-duty engine coolants for a facility such as the New Jersey Department of Transportation garage in Ewing, New Jersey. he specific recycling evaluated is b...

  16. Multifunctional Converter Drive for Automotive Electric Power Steering Systems

    NARCIS (Netherlands)

    Hackner, T.J.

    2013-01-01

    In this thesis it is shown that in the case of an automotive electric power steering system, critical pulse power loads can be decoupled from the power net with a storage element and a multifunctional converter. A multifunctional converter system is proposed because it uses the motor drive system as

  17. Advanced materials for application in the aerospace and automotive industries

    CSIR Research Space (South Africa)

    Damm, O

    2008-11-01

    Full Text Available The CSIR conducts research and development (R&D) involving advanced materials with applications in the local automotive and aerospace industries. The relevance of these R&D programmes is illustrated by positioning them in the context of key industry...

  18. Monitoring active filters under automotive aging scenarios with embedded instrument

    NARCIS (Netherlands)

    Wan, Jinbo; Kerkhoff, Hans G.

    2012-01-01

    In automotive mixed-signal SoCs, the analogue/mixed-signal front-ends are of particular interest with regard to dependability. Because of the many electrical disturbances at the front-end, often (active) filters are being used. Due to the harsh environments, in some cases, degradation of these filte

  19. Visual bias in subjective assessments of automotive sounds

    DEFF Research Database (Denmark)

    Ellermeier, Wolfgang; Legarth, Søren Vase

    2006-01-01

    In order to evaluate how strong the influence of visual input on sound quality evaluation may be, a naive sample of 20 participants was asked to judge interior automotive sound recordings while simultaneously being exposed to pictures of cars. twenty-two recordings of second-gear acceleration...

  20. Developing E-Learning Solutions in the Automotive Industry

    Science.gov (United States)

    Bogdan, Razvan; Ancusa, Versavia

    2016-01-01

    In the rapid developing market of automotive industry, cutting-edge technologies are being introduced. One such example is the AUTOSAR standard. Companies are investing a large amount of finances for the training of their employees into the intricacies of such technologies. In order to face such an increase of the training costs, automotive…

  1. Applied Physics Modules Selected for Automotive and Diesel Technologies.

    Science.gov (United States)

    Waring, Gene

    Designed for individualized use in an applied physics course in postsecondary vocational-technical education, this series of ten learning modules is equivalent to the content of a five-credit hour class in automotive technology or diesel technology. Almost all the modules contain technological application in the form of laboratory experiments or…

  2. Examples on cold forged aluminium components in automotive industry

    DEFF Research Database (Denmark)

    Bay, Niels; Kolsgaard, A.

    2000-01-01

    The present paper describes the possibilites of applying cold forging for manufacturing of light weight components in aluminium. A short description of the basic cold forming processes forms the basis for describing the great variety in design of cold forged components. Examples are mainly taken ...... from automotive industry but in a few cases also from other industrial sectors to show the possibilities....

  3. Flexible labour strategy in the Dutch automotive industry

    NARCIS (Netherlands)

    van Riemsdijk, Maarten; de Leede, Jan

    2001-01-01

    Labour flexibility is a major way for companies to become more flexible. Why companies use flexible labour relations varies widely per industry. We assess the development of labour flexibility within the Dutch automotive industry. Four cases, together representing the production chain, are

  4. Estimation of Kinetic Parameters in an Automotive SCR Catalyst Model

    DEFF Research Database (Denmark)

    Åberg, Andreas; Widd, Anders; Abildskov, Jens;

    2016-01-01

    A challenge during the development of models for simulation of the automotive Selective Catalytic Reduction catalyst is the parameter estimation of the kinetic parameters, which can be time consuming and problematic. The parameter estimation is often carried out on small-scale reactor tests, or p...

  5. Analysis of sound absorption of tuck spacer fabrics to reduce automotive noise

    Science.gov (United States)

    Dias, Tilak; Monaragala, Ravindra; Needham, Peter; Lay, Edward

    2007-08-01

    Textiles are widely used in the automotive industry to provide both comfort to the passengers and an aesthetic appearance to the automotive interior. They can also be used to reduce automotive interior noise, which can make automotive travel safer and more comfortable. Knitted fabrics are used widely in automotive upholstery; however, the sound absorbency of a single layer of a knitted fabric is inadequate for the reduction of automotive interior noise. This paper investigates the sound absorbency of a novel knitted spacer fabric, which can be used in automotive upholstery and has the potential for greater sound absorbency than a conventional plain knitted fabric and its derivatives. The spacer fabric is modelled as a porous sound absorber and its sound absorbency is studied with regard to its structural parameters.

  6. Acoustic response variability in automotive vehicles

    Science.gov (United States)

    Hills, E.; Mace, B. R.; Ferguson, N. S.

    2009-03-01

    A statistical analysis of a series of measurements of the audio-frequency response of a large set of automotive vehicles is presented: a small hatchback model with both a three-door (411 vehicles) and five-door (403 vehicles) derivative and a mid-sized family five-door car (316 vehicles). The sets included vehicles of various specifications, engines, gearboxes, interior trim, wheels and tyres. The tests were performed in a hemianechoic chamber with the temperature and humidity recorded. Two tests were performed on each vehicle and the interior cabin noise measured. In the first, the excitation was acoustically induced by sets of external loudspeakers. In the second test, predominantly structure-borne noise was induced by running the vehicle at a steady speed on a rough roller. For both types of excitation, it is seen that the effects of temperature are small, indicating that manufacturing variability is larger than that due to temperature for the tests conducted. It is also observed that there are no significant outlying vehicles, i.e. there are at most only a few vehicles that consistently have the lowest or highest noise levels over the whole spectrum. For the acoustically excited tests, measured 1/3-octave noise reduction levels typically have a spread of 5 dB or so and the normalised standard deviation of the linear data is typically 0.1 or higher. Regarding the statistical distribution of the linear data, a lognormal distribution is a somewhat better fit than a Gaussian distribution for lower 1/3-octave bands, while the reverse is true at higher frequencies. For the distribution of the overall linear levels, a Gaussian distribution is generally the most representative. As a simple description of the response variability, it is sufficient for this series of measurements to assume that the acoustically induced airborne cabin noise is best described by a Gaussian distribution with a normalised standard deviation between 0.09 and 0.145. There is generally

  7. Surface processing to improve the fatigue resistance of advanced bar steels for automotive applications

    Directory of Open Access Journals (Sweden)

    David K. Matlock

    2005-12-01

    Full Text Available With the development of new steels and processing techniques, there have been corresponding advances in the fatigue performance of automotive components. These advances have led to increased component life and smaller power transfer systems. New processing approaches to enhance the fatigue performance of steels are reviewed with an emphasis on carburizing and deep rolling. Selected examples are presented to illustrate the importance of the base steel properties on the final performance of surface modified materials. Results on carburized gear steels illustrate the dependence of the fatigue behavior on carburizing process control (gas and vacuum carburizing, alloy additions and microstructure. The importance of retained austenite content, case and core grain size as controlled by processing and microalloy additions, extent of intergranular oxidation, and the residual stress profile on fatigue performance is also illustrated. Specific recent results on the use of microalloying elements (e.g. Nb and process history control to limit austenite grain growth at the higher carburizing temperatures associated with vacuum carburizing are highlighted. For crankshaft applications, deep rolling is highlighted, a process to mechanically work fillet surfaces to improve fatigue resistance. The influence of the deformation behavior of the substrate, as characterized by standard tensile and compression tests, on the ability to create desired surface properties and residual stress profiles will be illustrated with data on several new steels of current and future interest for crankshaft applications.

  8. 基于有限元的大型枝丫粉碎机切削力分析%Analysis of the Cutting Force of Large Branch Shredders Based on Finite Element

    Institute of Scientific and Technical Information of China (English)

    杨春梅; 于盛通; 任长清; 罗阁

    2011-01-01

    对枝丫粉碎机的切削力进行研究,推导出切削力的计算公式,找出影响切削力的因素,并对受切削力作用的飞刀进行ANSYS有限元分析。%The study of the cutting force of branch shredder is made, the calculation formula of the cutting force is deduced, the factors influencing the cutting force are found out and the ANSYS finite element-based analysis of the flying cutters that are influenced by the cutting force is made.

  9. Effects of a triazole fungicide and a pyrethroid insecticide on the decomposition of leaves in the presence or absence of macroinvertebrate shredders.

    Science.gov (United States)

    Rasmussen, Jes Jessen; Monberg, Rikke Juul; Baattrup-Pedersen, Annette; Cedergreen, Nina; Wiberg-Larsen, Peter; Strobel, Bjarne; Kronvang, Brian

    2012-08-15

    Previously, laboratory experiments have revealed that freely diluted azole fungicides potentiate the direct toxic effect of pyrethroid insecticides on Daphnia magna. More ecologically relevant exposure scenarios where pesticides are adsorbed have not been addressed. In this study we exposed beech leaves (Fagus sylvatica) to the azole fungicide propiconazole (50 or 500 μg L(-1)), the pyrethroid insecticide alpha-cypermethrin (0.1 or 1 μg L(-1)) or any combination of the two for 3h. Exposed leaves were transferred to aquaria with or without an assemblage of macroinvertebrate shredders, and we studied treatment effects on rates of microbial leaf decomposition, microbial biomass (using C:N ratio as a surrogate measure) and macroinvertebrate shredding activity during 26 days post-exposure. Microbial leaf decomposition rates were significantly reduced in the propiconazole treatments, and the reduction in microbial activity was significantly correlated with loss of microbial biomass (increased C:N ratio). Macroinvertebrate shredding activity was significantly reduced in the alpha-cypermethrin treatments. In addition, the macroinvertebrate assemblage responded to the propiconazole treatments by increasing their consumption of leaf litter with lower microbial biomass, probably to compensate for the reduced nutritional quality of this leaf litter. We found no interaction between the two pesticides on macroinvertebrate shredding activity, using Independent Action as a reference model. In terms of microbial leaf decomposition rates, however, alpha-cypermethrin acted as an antagonist on propiconazole. Based on these results we emphasise the importance of considering indirect effects of pesticides in the risk assessment of surface water ecosystems.

  10. 新型耐磨焊条在破碎机上的应用%A New Type Electrode for Shredders

    Institute of Scientific and Technical Information of China (English)

    应鹏展; 王雅晴

    2001-01-01

    A wear-resistant electrode used in high stress state is studied.By adjusting electrode's component,we find a alloy system which is suitable to shredders with hammer.Microstructure and X-ray analyses indicate that the hardfacing microstructure consist of martensite,retained austenite and carbonide. The hardfacing hardness is between HRC62~64.Wearing resistance test and industrial practice had proved that wear-resistant of the hardfacing is 8.2 times as high as 45 steel's and its average service life can be prolonged by eight times longer than that of conventional way.%研制了一种适用于高冲击条件下抗磨堆焊焊条,通过反复调整焊条药皮组成,找到了可应用于锤式破碎机锤头堆焊的合金系。通过堆焊层的金相显微分析及X—射线物相分析表明:堆焊层组织为马氏体加碳化物加残余奥氏体,堆焊层的硬度为HRC62—64;高应力磨料磨损实验和工业试验证明:锤头堆焊合金的耐磨性能优良,是45钢的8.1倍,比未堆焊的锤头寿命提高了8倍。

  11. State Articulated Instructional Objectives Guide for Occupational Education Programs. State Pilot Model for Automotive Mechanics (DCC V-003) and Automotive Mechanics (High School).

    Science.gov (United States)

    North Carolina State Dept. of Community Colleges, Raleigh.

    This articulation instructional objective guide for automotive mechanics contains summary information on fifteen blocks (courses) of instruction. They are introduction to automotive technology; lubrication and vehicle operating maintenance; cooling system maintenance and repair; automobile heater maintenance and repair; braking system maintenance…

  12. Learning, Upgrading, Innovation in the South African Automotive Industry

    DEFF Research Database (Denmark)

    Barnes, Justin; Lorentzen, Jochen

    2003-01-01

    , their internal upgrading and R&D agenda, and their interface with South Africa's national innovation system (NIS). The analysis makes use of eight case studies, and illustrates the conditions under which indigenous innovation in the automotive industries can happen in a developing country. This finding......This paper addresses the innovation activities of automotive component manufacturers in South Africa. It looks at the technological trajectory of a handful of firms that stand out from the crowd and analyses the results of their endeavours in the context of their interaction with foreign capital...... contradicts at least part of the conventional wisdom concerning the location of innovation activities in global car value chains. Results also point to a deficient NIS insofar as there appears to be a disjuncture between the demand for engineering competence in the manufacturing sector on the one hand...

  13. Sustainability and Energy Efficiency in the Automotive Sector

    CERN Document Server

    CERN. Geneva

    2013-01-01

    Since this year there can be no doubt that "sustainability" has become the top issue in the automotive sector. Volkswagen's CEO Prof. Dr. Martin Winterkorn attacked incumbents like BMW Group (so far the "most sustainable car manufacturer" for the 8th consecutive year) or Toyota (producer of the famous "Prius") head-on by boldly stating to become "the most profitable and most sustainable car manufacturer worldwide by 2018" . This announcement clearly shows that "sustainability" and "profitability" no longer are considered as conflicting targets. On the contrary, to Prof. Dr. Winterkorn : "climate protection is a driver for economic growth". To prime discussions, the plenary talk will give a brief overview of the entire range of energy efficiency in the automotive sector: based on the multiple drivers behind energy efficiency, practical examples are presented along the entire life-cycle of cars (R&D, production, usage and recycling). These "cases" include big automobile producers as well as their respectiv...

  14. A Comparative Study on Automotive Brake Testing Standards

    Science.gov (United States)

    Kumbhar, Bhau Kashinath; Patil, Satyajit Ramchandra; Sawant, Suresh Maruti

    2016-06-01

    Performance testing of automotive brakes involves determination of stopping time, distance and deceleration level. Braking performance of an automobile is required to be ensured for various surfaces like dry, wet, concrete, bitumen etc. as well as for prolonged applications. Various brake testing standards are used worldwide to assure vehicle and pedestrian safety. This article presents methodologies used for automotive service brake testing for two wheelers. The main contribution of this work lies in comparative study of three main brake testing standards; viz. Indian Standards, Federal Motor Vehicle Safety Standards and European Economic Commission Standards. This study shall help the policy makers to choose the best criteria out of these three while formulating newer edition of testing standards.

  15. Automotive Technology and Human Factors Research: Past, Present, and Future

    Directory of Open Access Journals (Sweden)

    Motoyuki Akamatsu

    2013-01-01

    Full Text Available This paper reviews the history of automotive technology development and human factors research, largely by decade, since the inception of the automobile. The human factors aspects were classified into primary driving task aspects (controls, displays, and visibility, driver workspace (seating and packaging, vibration, comfort, and climate, driver’s condition (fatigue and impairment, crash injury, advanced driver-assistance systems, external communication access, and driving behavior. For each era, the paper describes the SAE and ISO standards developed, the major organizations and conferences established, the major news stories affecting vehicle safety, and the general social context. The paper ends with a discussion of what can be learned from this historical review and the major issues to be addressed. A major contribution of this paper is more than 180 references that represent the foundation of automotive human factors, which should be considered core knowledge and should be familiar to those in the profession.

  16. 4th International Conference on Sustainable Automotive Technologies

    CERN Document Server

    Wellnitz, Jörg; Leary, Martin; Koopmans, Lucien

    2012-01-01

    The book on Sustainable Automotive Technologies aims to draw special attention to the research and practice focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. In particular, the book features incremental and radical technical advancements that are able to meet social, economic and environmental targets in both local and global contexts. These include original solutions to the problems of pollution and congestion, vehicle and public safety, sustainable vehicle design and manufacture, new structures and materials, new power-train technologies and vehicle concepts. In addition to vehicle technologies, the book is also concerned with the broader systemic issues such as sustainable supply chain systems, integrated logistics and telematics, and end-of-life vehicle management. It captures selected peer reviewed papers accepted for presentation at the 4th International Conference on Sustainable Automotive Technologies, ICSAT2012, held at the RMIT, Melbourne, Australi...

  17. Economic crisis and the automotive industry in Romania

    Directory of Open Access Journals (Sweden)

    Iosip, A.

    2010-12-01

    Full Text Available The economic crisis has affected many areas but the auto industry is perhaps one of the most affected. Renault, Ford, General Motors, Toyota, Volkswagen, BMW are just some of the big players caught unprepared. Through this paper we propose an analysis of the automotive market in Romania in order to understand the sales decrease of the last two years. At the same time we aimed at understanding the reasons that led to a decrease in car sales, what were the measures taken by the government to stop this phenomenon and how the economic crisis influenced the automotive field in Romania. An objective image of the situation in the automobile market in Romania at this moment also requires an analysis of the marketing environment and the changes it has undergone over time. Last but not least we will try to find a series of measures to re-launch the car market in Romania.

  18. Suitability of Alternative Lubricants for Automotive Gear Applications

    Directory of Open Access Journals (Sweden)

    Amit Suhane

    2014-03-01

    Full Text Available Rising environmental concerns due to the problems associated with conventional mineral lubricants has renewed interest in usage of alternative resources. Various attempts have been made to explore the possibilities of utilizing vegetable oils for range of applications. Properties like excellent viscosity features, higher biodegradability, lower toxicity, better renewability & natural lubricity etc shows its potential as lubricants inspite of certain technical problems. Critical issues like lower oxidation stability , poor cold temperature properties affects the performance of vegetable oils and restricts its application to limited range . Gear oils are the hidden workhorses of automotive applications. This article highlights the suitability of various vegetable oils for lubricant formulation as an alternative in automotive gearing applications.

  19. Development of nanolubricant automotive air conditioning (AAC test rig

    Directory of Open Access Journals (Sweden)

    Redhwan A.A.M.

    2017-01-01

    Full Text Available Nanolubricant been introduced in compressor might improve the performance of automotive air conditioning system. Prior testing of the nanolubricant enhancement performance, an automotive air conditioning (AAC system test rig base on compact car has to be developed; therefore this paper presented the development process of AAC test rig. There are 15 thermocouples, 2 pressure gauges and power analyzer were assembled on the system in order to analyse its performance. The experiment was conducted with four different charged of refrigerant. The charging was based on initial weight charged. At each quantity of refrigerant charge, performance of the AAC system was evaluated by determining three important parameters which is cooling capacity, compressor work and coefficient of performance (COP. The maximum average COP is achieved at 900 RPM is 7.07. The average and maximum COP enhancement of 7.07 % and 13.34 % were achieved by applying SiO2 nanolubricant inside the compressor.

  20. 20th International Forum on Advanced Microsystems for Automotive Applications

    CERN Document Server

    Müller, Beate; Meyer, Gereon

    2016-01-01

    This book contains the papers presented at the 20th anniversary edition of the AMAA conference held in Brussels, Belgium in 2016. The theme of the conference was "Smart Systems for the Automobile of the Future". The automobile is currently being reshaped at unprecedented pace. Automation and electrification are the two dominant megatrends which dramatically change the choice and design of components, systems, vehicular architectures and ultimately the way we use cars in the coming decades. Novel E/E architectures, vehicular connectivity and cloud services will be key to extending the perception and decision-making horizons of automated vehicles, to enable cooperative functions and a seamless digital user experience. The AMAA's ongoing mission to detect novel trends in automotive ICT, electronics and smart systems and to discuss the technological implications is once again reflected in this volume. The book will be a valuable read for research experts and professionals in the automotive and smart systems indus...

  1. Experimental Research of Automotive Needlepunched Carpets at Thermoforming Temperatures

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yun-qing; GUO Zhi-ying; DONG xiang-huai; LI De-qun

    2007-01-01

    Tensile prerties with different thermoformingconditions and deformation mechanism at thermoformingtemperatures of automotive needlepunched carpets made up ofthree layers of different materials were reported.Investigations on the tensile properties were performed as afunction of thermoforming temperature, extensile speed andfiber orientation based on an orthogonal experiment design.The experimental results show that the automotive carpets arerate-dependent anisotropic one and very sensitive to theforming temperature. The tensile properties are stronglydepended an the forming temperature when compared with theextensile speed and the fiber orientation. Experiments onlyvarying with the temperature were performed because of thedominative effect of the temperature. Different defotmationperformances were observed with different temperatures.Deformation mechanisms at the thermoforming temperatureswere presented to explain the nonlinear trend of the ultimateelongation with the temperatures based on the combination ofthe experimental observations and the corresponding polymertheories.

  2. Identifying Lead Markets in the European Automotive Industry

    DEFF Research Database (Denmark)

    Cleff, Thomas; Grimpe, Christoph; Rammer, Christian

    2015-01-01

    of excellence in technology and interaction among users and producers, the lead market approach focuses on the role of demand characteristics. Based on the concept of innovation design, a lead market is defined as a country where customers prefer that design which subsequently becomes the globally dominant......This paper presents an indicator-based methodology to identify lead markets in the European automotive industry. The lead market approach tries to explain why certain countries are better positioned than others for developing and launching new products. While much research stresses the role...... design. We use an indicator-based approach which has been successfully employed for individual products as well as for various industries in order to identify lead markets in the European automotive industry. Employing five lead market factors, our results show that the EU is by far no homogeneous market...

  3. Impact of novel thermoelectric materials on automotive applications

    Science.gov (United States)

    Brignone, Mauro; Ziggiotti, Alessandro

    2012-06-01

    Despite the fact that thermoelectric (TE) devices are compact, quiet, rugged, stable and very reliable, thermoelectrics have found only niche applications because they are also inefficient (less that 5% conversion efficiency is typical) and costly. The key to more widespread acceptance of thermoelectric is the development of materials that are capable of higher conversion efficiency, but other fundamental materials parameters play a role not less important to open to large applications and markets. In particular the automotive sector requires low materials density, materials made from widely-available pure elements with very large supply chains, non-toxicity of elements and potential compliance with REACH and RoHS obligations and low raw material cost combined with low manufacturing costs. The impact of novel TE materials on automotive application will be described focusing on promising nano magnesium silicide and skutterudites.

  4. Mockup Didatic Set for Students Development in Automotive Electronic

    Directory of Open Access Journals (Sweden)

    Fabio Delatore

    2013-05-01

    Full Text Available The automotive engineering education area, specifically on internal combustion engine, requires the use of suitable systems, capable to simulate, test and obtain specifics data from its operation. Automotive engines are so complex due to it is a mix of engineering subjects, so, a mockup was created to help its study. The mockup is an exactly the same engine that equips a vehicle, but assembled in a mechanical base, equipped with all the necessary components for running it up. The objective of this work is to develop a mockup with a suitable Electronic Control Unit (ECU board, in order to obtain the sensors/actuators signals from the engine and control some important engine functions by using an external ECU, so that the students may test their own strategies, compare with the original ECU.

  5. A Comparative Study on Automotive Brake Testing Standards

    Science.gov (United States)

    Kumbhar, Bhau Kashinath; Patil, Satyajit Ramchandra; Sawant, Suresh Maruti

    2017-08-01

    Performance testing of automotive brakes involves determination of stopping time, distance and deceleration level. Braking performance of an automobile is required to be ensured for various surfaces like dry, wet, concrete, bitumen etc. as well as for prolonged applications. Various brake testing standards are used worldwide to assure vehicle and pedestrian safety. This article presents methodologies used for automotive service brake testing for two wheelers. The main contribution of this work lies in comparative study of three main brake testing standards; viz. Indian Standards, Federal Motor Vehicle Safety Standards and European Economic Commission Standards. This study shall help the policy makers to choose the best criteria out of these three while formulating newer edition of testing standards.

  6. Current and Future Uses of Aluminum in the Automotive Industry

    Science.gov (United States)

    Long, R. S.; Boettcher, E.; Crawford, D.

    2017-08-01

    Aluminum use is growing in automotive closures and body in white applications to improve vehicle performance and fuel economy. The auto industry is looking for higher-strength aluminum materials needed for strength-driven safety-critical parts. Through cooperation with industrial partners and support from the Department of Energy (DOE), multiple experimental 7xxx alloys were developed for automotive applications. The objective is to enable complex shapes to be formed at temperatures below 225°C. A demonstration part has been developed that is representative of the forming challenges within a current hot-stamped door ring component. This part tooling has been built and installed into a press line which includes blank heating and robotic transfer. Forming trials of these alloys are currently underway and the formability, strength and corrosion performance of these materials are being evaluated.

  7. Making aerospace technology work for the automotive industry, introduction

    Science.gov (United States)

    Olson, W. T.

    1978-01-01

    NASA derived technology already in use in the automotive industry include: (1) developments in electronics design, computer systems, and quality control methods for line testing of cars and trucks; (2) a combustion analysis computer program for automotive engine research and development; (3) an infrared scanner and television display for analyzing tire design and performance, and for studying the effects of heat on the service life of V-belts, shock mounts, brakes, and rubber bearings; (4) exhaust gas analyzers for trouble shooting and emissions certification; (5) a device for reducing noise from trucks; and (6) a low cost test vehicle for measuring highway skid resistance. Services offered by NASA to facilitate access to its technology are described.

  8. Environmental management and operational performance in automotive companies in Brazil

    DEFF Research Database (Denmark)

    Jabbour, C.J.C.; De Sousa Jabbour, A.B.L.; Govindan, Kannan

    2013-01-01

    The main objective of this study is to verify the influence of Environmental Management (EM) on Operational Performance (OP) in Brazilian automotive companies, analyzing whether Lean Manufacturing (LM) and Human Resources (HR) interfere in the greening of these companies. Therefore, a conceptual...... from 75 companies, were analyzed using structural equation modeling. The main results are as follows: (a) the model tested revealed an adequate goodness of fit, showing that overall, the relations proposed between EM and OP and between HR, LM and EM tend to be statistically valid; (b) EM tends....... The originality of this paper lies in its gathering the concepts of EM, LM, HR and OP in a single study, as they generally tend not to be treated jointly. This paper also provided valid empirical evidence for a littlestudied context: the Brazilian automotive sector....

  9. Automotive Control Systems: For Engine, Driveline, and Vehicle

    Science.gov (United States)

    Kiencke, Uwe; Nielsen, Lars

    Advances in automotive control systems continue to enhance safety and comfort and to reduce fuel consumption and emissions. Reflecting the trend to optimization through integrative approaches for engine, driveline, and vehicle control, this valuable book enables control engineers to understand engine and vehicle models necessary for controller design, and also introduces mechanical engineers to vehicle-specific signal processing and automatic control. The emphasis on measurement, comparisons between performance and modeling, and realistic examples derive from the authors' unique industrial experience

  10. Technology Roadmap for Energy Reduction in Automotive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    none,

    2008-09-01

    U.S. Department of Energy’s (DOE) Industrial Technologies Program (ITP), in collaboration with the United States Council for Automotive Research LLC (USCAR), hosted a technology roadmap workshop in Troy, Michigan in May 2008. The purpose of the workshop was to explore opportunities for energy reduction, discuss the challenges and barriers that might need to be overcome, and identify priorities for future R&D. The results of the workshop are presented in this report.

  11. The Quantitative Analysis of Chennai Automotive Industry Cluster

    Science.gov (United States)

    Bhaskaran, Ethirajan

    2016-07-01

    Chennai, also called as Detroit of India due to presence of Automotive Industry producing over 40 % of the India's vehicle and components. During 2001-2002, the Automotive Component Industries (ACI) in Ambattur, Thirumalizai and Thirumudivakkam Industrial Estate, Chennai has faced problems on infrastructure, technology, procurement, production and marketing. The objective is to study the Quantitative Performance of Chennai Automotive Industry Cluster before (2001-2002) and after the CDA (2008-2009). The methodology adopted is collection of primary data from 100 ACI using quantitative questionnaire and analyzing using Correlation Analysis (CA), Regression Analysis (RA), Friedman Test (FMT), and Kruskall Wallis Test (KWT).The CA computed for the different set of variables reveals that there is high degree of relationship between the variables studied. The RA models constructed establish the strong relationship between the dependent variable and a host of independent variables. The models proposed here reveal the approximate relationship in a closer form. KWT proves, there is no significant difference between three locations clusters with respect to: Net Profit, Production Cost, Marketing Costs, Procurement Costs and Gross Output. This supports that each location has contributed for development of automobile component cluster uniformly. The FMT proves, there is no significant difference between industrial units in respect of cost like Production, Infrastructure, Technology, Marketing and Net Profit. To conclude, the Automotive Industries have fully utilized the Physical Infrastructure and Centralised Facilities by adopting CDA and now exporting their products to North America, South America, Europe, Australia, Africa and Asia. The value chain analysis models have been implemented in all the cluster units. This Cluster Development Approach (CDA) model can be implemented in industries of under developed and developing countries for cost reduction and productivity

  12. Dynamic design of automotive systems: Engine mounts and structural joints

    Indian Academy of Sciences (India)

    R Singh

    2000-06-01

    Dynamic design and vibro-acoustic modelling issues for automotive structures are illustrated via two case studies. The first case examines the role performance of passive and adaptive hydraulic engine mounts. In the second, the importance of welded joints and adhesives in vehicle bodies and chassis structures is highlighted via generic 'T' and 'L' beams assemblies. In each case, analytical and experimental results are presented. Unresolved research issues are briefly discussed.

  13. Present and Future Automotive Composite Materials Research Efforts at DOE

    Energy Technology Data Exchange (ETDEWEB)

    Warren, C.D.

    1999-07-03

    Automobiles of the future will be forced to travel fi.uther on a tank of fuel while discharging lower levels of pollutants. Currently, the United States uses in excess of 16.4 million barrels of petroleum per day. Sixty-six percent of that petroleum is used in the transportation of people and goods. Automobiles currently account for just under two-thirds of the nation's gasoline consumptio~ and about one-third of the total United States energy usage. [1] By improving transportation related fiel efficiency, the United States can lessen the impact that emissions have on our environment and provide a cleaner environment for fiture generations. In 1992, The Department of Energy's (DOE) Office of Transportation Materials completed a comprehensive program plan entitled, The Lightweight MateriaIs (LWko Multi-Year Program Plan, for the development of technologies aimed at reducing vehicle mass [2]. This plan was followed in 1997 by the more comprehensive Office of Advanced Automotive Technologies research and development plan titled, Energy Eficient Vehicles for a Cleaner Environment [3] which outlines the department's plans for developing more efficient vehicles during the next ~een years. Both plans identi~ potential applications, technology needs, and R&D priorities. The goal of the Lightweight Materials Program is to develop materials and primary processing methods for the fabrication of lighter weight components which can be incorporated into automotive systems. These technologies are intended to reduce vehicle weight, increase fuel efficiency and decrease emissions. The Lightweight Materials program is jointly managed by the Department of Energy(DOE) and the United States Automotive Materials Partnership (USAMP). Composite materiak program work is coordinated by cooperative research efforts between the DOE and the Automotive Composites Consortium (ACC).

  14. Evolution of Business Interoperability in the Automotive Industry

    OpenAIRE

    Wende, Kristin; Legner, Christine

    2006-01-01

    In recent years, the established roles in the automotive industry have undergone changes: Automakers which have traditionally executed control over the entire value chain are now increasingly focusing on branding and distribution. At the same time, tier-1 suppliers are becoming vehicle integrators. This paper analyses how new forms of cooperation impact the required level of business interoperability. The comparison of two cases, a traditional OEM-supplier relationship and an innovative form ...

  15. French approval procedures for pyrotechnical automotive safety equipments

    OpenAIRE

    Aufauvre, Lionel; Branka, Ruddy

    2005-01-01

    International audience; Pyrotechnical articles for civil uses may be subject to national procedures before placing on the market According to the French decree n°90-153, 16 February 1990 as modified; explosives that are dispensed with EC marking and that are not excluded of the decree application have to conform to approved types. Pyrotechnical automotive safety equipments such gas generators for airbag modules or seat-belt pretensioners, pyrotechnie relay compositions and/or igniters inside ...

  16. FINANCIAL RISKS – A CASE STUDY FOR AUTOMOTIVE INDUSTRY

    OpenAIRE

    Herciu, Mihaela; OGREAN Claudia

    2013-01-01

    In general, financial risks – from operational risk to bankruptcy risk, are important distress for companies from every sector or industry. In this paper we try to measure the financial risk for the most important eight companies that activate in automotive industry. We propose a model in order to evaluate financial risk, by using discriminate analysis, which integrate five of the most important financial indicators: current ratio, return on investment, debt to equity, total assets turnover, ...

  17. Two-Mode Operation Engine Mount Design for Automotive Applications

    OpenAIRE

    Reza Tikani; Nader Vahdati; Saeed Ziaei-Rad

    2012-01-01

    Hydraulic engine mounts are applied to the automotive applications to isolate the chassis from the high frequency noise and vibration generated by the engine as well as to limit the engine shake motions resulting at low frequencies. In this paper, a new hydraulic engine mount with a controllable inertia track profile is proposed and its dynamic behavior is investigated. The profile of the inertia track is varied by applying a controlled force to a cylindrical rubber disk, placed in the inerti...

  18. Cost and Price Metrics for Automotive Lithium-Ion Batteries

    Energy Technology Data Exchange (ETDEWEB)

    None

    2017-02-01

    Values of current energy technology costs and prices, available from a variety of sources, can sometimes vary. While some of this variation can be due to differences in the specific materials or configurations assumed, it can also reflect differences in the definition and context of the terms "cost" and "price." This fact sheet illustrates and explains this latter source of variation in a case study of automotive lithium-ion batteries.

  19. A rubber mount model. Application to automotive equipment suspension

    OpenAIRE

    Manin, Lionel; Dufour, Régis; Thomas, Benjamin; Goge, Philippe

    2010-01-01

    International audience; In order to predict the nonlinear dynamic response of automotive equipment supported by rubber mounts, it is proposed to extend the generalized Dahl model for taking into account the visco-elastic behaviour of elastomer mount and to combine it, in a next step, with the reduced dynamic equations of the equipment supposed to exhibit a linear behaviour. To this end, the parameters of the restoring force model of the mounts are identified through a series of tests accounti...

  20. Design and Test of an Automotive Clutch Actuation

    OpenAIRE

    Meloni, Michele

    2012-01-01

    This thesis builds on the analysis of a automatic system for automotive automatic clutches. In this field of study there are some constraint to take into account and through them it is possible to find the best technological solution. The system under consideration is characterized as electromechanical, with an electric motor brush DC and reduction system very complex. The system was modeled using the Bond-Graph technique which allowed the drafting of the dynamical system equations, in state ...

  1. Wear effects and mechanisms of soot-contaminated automotive lubricants

    OpenAIRE

    Green, D. A.; Lewis, R; Dwyer-Joyce, R.S.

    2006-01-01

    A study has been carried out to investigate the influence of soot-contaminated automotive lubricants in the wear process of a simulated engine valve train contact. Previous research on this topic has been mainly performed from a chemical point of view in fundamental studies, with insufficient relevance to real engine conditions, i.e. load and geometry. This study investigates the conditions under which wear occurs through specimen testing. The objective of the work was to understand the wear ...

  2. Automotive Lighting将在中国投资设厂

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    意大利车灯供应商Automotive Loghting日前宣布,将在中国投资700万欧元建厂.工厂选址在安徽芜湖。该工厂预计将于明年初投产,目前公司已经在做挑选供应商的准备。

  3. Automotive radar – investigation of mutual interference mechanisms

    OpenAIRE

    2010-01-01

    In the past mutual interference between automotive radar sensors has not been regarded as a major problem. With an increasing number of such systems, however, this topic is receiving more and more attention. The investigation of mutual interference and countermeasures is therefore one topic of the joint project "Radar on Chip for Cars" (RoCC) funded by the German Federal Ministry of Education and Research (BMBF). RoCC's goal is to pave the way for the development of high-per...

  4. Planar millimeter wave radar frontend for automotive applications

    OpenAIRE

    2003-01-01

    A fully integrated planar sensor for 77 GHz automotive applications is presented. The frontend consists of a transceiver multichip module and an electronically steerable microstrip patch array. The antenna feed network is based on a modified Rotman-lens and connected to the array in a multilayer approach offering higher integration. Furthermore, the frontend comprises a phase lock loop to allow proper frequency-modulated continuous wave (FMCW) radar operation. The latest experimental results ...

  5. Phased array antenna element for automotive radar application

    OpenAIRE

    2014-01-01

    In this thesis work, a design of reliable antenna front-end for W band automotive radar is studied and the problems and considerations associated with phased array antenna design at W-band are addressed. Proposed phased array antenna consists of on chip patch antenna which has the advantages of being integrated by the active circuitry. A sample of patch antenna and patch array are designed and fabricated to be tested for their functionality. Printing antenna on Silicon substrate is a compact ...

  6. Performance Management Analytics for the Automotive Industry: An Empirical Study

    OpenAIRE

    João Carlos Dias Correia Pinto

    2016-01-01

    The automotive industry is permanently collecting data about the business that is then used to calculate high level Key Performance Indicators (KPI) that are organized on a Performance Management System (PMS) to help on the decision making process. However, these KPIs represent uniquely the past. The business, in order to be proactive "i.e." create the future, must predict how it will be. Using Data Mining, Machine Learning, Statistics and Artificial Intelligence tis project creates and compa...

  7. Thermal comfort findings: Scenario at Malaysian automotive industry

    Directory of Open Access Journals (Sweden)

    Ismail Ahmad Rasdan

    2013-01-01

    Full Text Available This paper discusses the findings of thermal comfort assessment at Malaysian automotive industry. Nine critical workstations were chosen as subjects for the study in order to determine the thermal comfort among workers at Malaysian automotive industry. The human subjects for the study comprises of the operators from tire receiving, dashboard assembly, drum tester, body assembly, seat assembly, door check assembly, stamping workstation, engine sub assembly and paint shop of the factory. The environmental factors such as Wet Bulb Globe Temperature (WBGT, relative humidity, air velocity, illuminance were measured using BABUC A apparatus and Thermal Comfort Measurement equipment. Through questionnaire survey, the demographic data of subjects and their perceptions on thermal comfort at each workstation were assessed based on ISO Standard 7730 and thermal sensation scale using Predicted Mean Vote (PMV. Then, Predicted Percentage of Dissatisfied (PPD is used to estimate the thermal satisfaction of occupants. The results indicated that most of the workstations of the automotive industry are considered as uncomfortable. Tire receiving station is considered having better working environment compared to other stations with lowest PMV index of 1.09 to 1.41 and PPD of 46%. Meanwhile, the engine sub assembly station and paint shop of assembly are considered the worst thermal environment with the PMV index values ranging between 2.1 to 2.9 and PPD values of 81% to 99%. Therefore, these two workstations are considered not comfortable because the thermal sensation scale is warm and almost hot.

  8. Application of Electron Beam Surface Technologies in the Automotive Industry

    Institute of Scientific and Technical Information of China (English)

    Rolf Zenker; Anja Buchwalder

    2004-01-01

    Progress in the beam deflection technique opens up new possibilities for the application of electron beam (EB)surface and welding technologies in the automotive industry. This development is based on three-dimensional high-speed beam deflection and fully automatic online process control. So, in the EB surface treatment three-dimensional energy transfer fields can be realised which take into account the contour of a component, the conditions of heat conduction and the load conditions. High flexibility, precision and reproducibility are typical characteristics. High productivity is achieved by the simultaneous interaction of the EB in several processing areas or by carrying out several processes simultaneously. EB surface treatment is becoming more and more attractive and important especially in the automotive industry, and also in comparison to laser technologies. This paper deals with different EB surface technologies, for example hardening,remelting, surface alloying, dispersing or cladding of different materials such as steel, cast iron and different alloys of Al,Mg and Ti. Examples of applications in the automotive industry, especially engine components, will be discussed.

  9. Nano-crystalline P/M aluminium for automotive applications

    Science.gov (United States)

    Hummert, K.; Schattevoy, R.; Broda, M.; Knappe, M.; Beiss, P.; Klubberg, F.; Schubert, T. H.; Leuschner, R.

    2009-01-01

    The reduction of total vehicle weight and lowering of moving masses within the engine are key elements to overcome future emission challenges of the automotive industry. Within a German BMBF funded project the melt spinning technology will be driven to a series production status. The very fast cooling condition of the melt leads to a nano-structure of the aluminium material. This results in new material properties of known alloys. The strength increases dramatically without lowered forming behaviour. With this process the freedom of designing complex alloys is very flexible. Different alloys have been investigated for several applications, where high strength at room and elevated temperatures and/or high wear resistance is required. This paper presents some results regarding the processing, microstructure and mechanical properties of a developed Al-Ni-Fe alloy. This joined research project with partners from the automotive industry as well as automotive suppliers and universities is funded by the German BMBF "NanoMobile" Program under Project number 03X3008.

  10. Framework to Analyse Automotive Interiors with a Focus on Ergonomics

    Directory of Open Access Journals (Sweden)

    Kajaria Nikhil

    2014-04-01

    Full Text Available The small car market in India is increasing by leaps and bounds. The market for small cars now occupies a substantial share of around 70% of the annual car production in India of about one million. The main players in the car market like Tata Motors, Maruti Udyog and Hyundai etc. are fiercely competitive and are trying to outdo each other in terms of design and technology. However, ultimately the focus of a manufacturer is providing customer satisfaction which is driven by comfort and ease of use. Automotive ergonomics is the study of how automotive can be designed better for human use. The human factor aspect of designing automobiles is first considered at the Vehicle Packaging stage. The term Vehicle Packaging comes to use whenever a new model is in the early stage of study. It is a method to safeguard and protect space for the human user and necessary components that make up the vehicle being designed. The improvement in the vehicle ergonomics requires a basic understanding of the problems that arise due to the conventional automotive interior design.

  11. Optical design of LED-based automotive tail lamps

    Science.gov (United States)

    Domhardt, André; Rohlfing, Udo; Klinger, Karsten; Manz, Karl; Kooß, Dieter; Lemmer, Uli

    2007-09-01

    The application of ultra bright monochromatic and white High-Power-LEDs in the range of automotive lighting systems is now state of the art. These LEDs offer new possibilities in optical design and engineering within different fields of automotive lighting, e.g., tail lamps, signal lamps, headlamps and interior lighting. This contribution describes the process of the optical design of an automotive LED tail lamp based on a practical example. We will elaborate the principal geometric approach, the radiometric conditions and the optical design by using standard and advanced mathematical optimization methods. Special attention will be paid to the following topics: efficient light coupling from the LED into the optical device, adaptation of the illuminance and optimization with respect to the requirements from SAE/ECE regulations. It will be shown that the development of LED-lamps requires the complex interaction of several factors. The challenge for the optical designer is to fulfill the technical demands while also considering the appearance of the final product desired by the customer. Further design specifications emerge from the electrical and thermal layout of the lamp.

  12. Cobalt asthma in metalworkers from an automotive engine valve manufacturer.

    Science.gov (United States)

    Walters, G I; Robertson, A S; Moore, V C; Burge, P S

    2014-07-01

    Cobalt asthma has previously been described in cobalt production workers, diamond polishers and glassware manufacturers. To describe a case series of occupational asthma (OA) due to cobalt, identified at the Birmingham Heartlands Occupational Lung Disease Unit, West Midlands, UK. Cases of cobalt asthma from a West Midlands' manufacturer of automotive engine valves, diagnosed between 1996 and 2005, were identified from the SHIELD database of OA. Case note data on demographics, employment status, asthma symptoms and diagnostic tests, including spirometry, peak expiratory flow (PEF) measurements, skin prick testing (SPT) and specific inhalational challenge (SIC) tests to cobalt chloride, were gathered, and descriptive statistics used to illustrate the data. The natural history of presentations has been described in detail, as well as a case study of one of the affected workers. Fourteen metalworkers (86% male; mean age 44.9 years) were diagnosed with cobalt asthma between 1996 and 2005. Workers were principally stellite grinders, stellite welders or machine setter-operators. All workers had positive Occupational Asthma SYStem analyses of serial PEF measurements, and sensitization to cobalt chloride was demonstrated in nine workers, by SPT or SIC. We have described a series of 14 workers with cobalt asthma from the automotive manufacturing industry, with objective evidence for sensitization. Health care workers should remain vigilant for cobalt asthma in the automotive manufacturing industry. © The Author 2014. Published by Oxford University Press on behalf of the Society of Occupational Medicine. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  13. History and evolution of warning labels for automotive friction products.

    Science.gov (United States)

    Kopelovich, Luda M; Thuett, Kerry A; Chapman, Pamela S; Paustenbach, Dennis J

    2014-04-01

    There have been claims over the years that asbestos-containing product manufacturers did not sufficiently warn end users early enough regarding the potential health hazards associated with their products (1930s-1990s). To address this issue, we compared the content of the warnings associated with asbestos-containing friction products (brakes, clutches, and gaskets) manufactured by the US automotive industries to what was expected by regulatory agencies during the time period in which an understanding of asbestos health hazards was being developed. We ended our evaluation around 1990, since asbestos-containing manufacturer supplied automotive products were functionally removed from commerce by 1985 in the United States. We assessed the warnings issued in users' manuals, technical service bulletins, product packaging materials, and labels placed on products themselves. Based on our evaluation, regulatory agencies had no guidelines regarding specific warning language for finished friction products, particularly when a product contained encapsulated asbestos fibers (i.e., modified by a bonding agent). Even today, federal regulations do not require labeling on encapsulated products when, based on professional judgment or sampling, user exposure is not expected to exceed the OSHA PEL. We concluded that, despite limited regulatory guidance, the US automotive industry provided adequate warnings with regards to its friction products. Copyright © 2014 Elsevier Inc. All rights reserved.

  14. Experimental and numerical analysis of automotive gearbox rattle noise

    Science.gov (United States)

    Kadmiri, Younes; Rigaud, Emmanuel; Perret-Liaudet, Joël; Vary, Laurence

    2012-06-01

    The aim of this work is to characterize the rattle noise of automotive gearboxes, resulting from impacts between toothed wheels of unselected gear ratios. These stereo-mechanical impacts are modeled by a coefficient of restitution which describes damping during the squeezing of the lubricant film for approaching surfaces, and the elastic deformation of impacting bodies. The dynamic response of the loose gear first depends on the design parameters and the engine operating conditions. The unknown parameters are the drag torque and the coefficient of restitution. They are identified experimentally through implementation of two optical encoders in an actual automotive gearbox and the operation of a specific test bench which replicates the automotive power train. Models of the different drag torque sources are validated from analysis of the free damped response of the driveline. The coefficient of restitution and its probability density function are measured from experiments under stationary operating conditions. A nonlinear model is built. The dynamic response of the loose gear depends on the dimensionless backlash, the coefficient of restitution and a dimensionless parameter proposed to describe the rattle excitation level. Experiments under controlled excitation are performed to validate the assumptions, to confirm the ability of the parameter proposed to describe the rattle noise threshold, and to characterize the dynamic response. The nonlinear model predictions are fitted with the drag torque and coefficient of restitution previously identified. They are compared with measurements to demonstrate the ability of the model to predict gear rattle for any loose gear, any gearbox and any operating condition.

  15. The analysis of experimental data obtained from automotives tests

    Science.gov (United States)

    Stoica, R. M.; Radulescu, V. J.; Neagu, D.; Trocan, C.; Copae, I.

    2016-08-01

    The paper highlights the three important and inseparably aspects of the systemic approach of automotives dynamics: taking into account the human-vehicle-field interaction, dealing movement with algorithms specific to system theory and analysis of experimental data with algorithms specific to signals theory.Within the paper, the systemic approach regarding vehicles dynamics is based on experimental data obtained from tests, whereby it is analyzed the movement and there are obtained movement mathematical models through algorithms of systems identification.Likewise, there are shown main analysis methods for experimental data, which uses probability theory, information theory, correlation analysis and variance analysis;in addition, there are highlighted possibilities given by time analysis, frequency analysis and data time-frequency analysis. Identification algorithms and highlighted analysis procedures assure the study of automotives dynamics and fuel saving,by directly using experimental data, or by using mathematical models and applying concepts and algorithms specific to systems theory. Experimental data were obtained by testing automotives with electronic control devices and by using acquisition and storage equipmentsfor data given by the on-board computer and taken from embedded sensors.

  16. MSc degree in color technology for the automotive sector

    Science.gov (United States)

    Martinez-Verdu, F.; Perales, E.; Chorro, E.; Viqueira, V.; Gilabert, E.

    2014-07-01

    Nowadays, the measurement and management of color quality of the gonio-apparent materials is complex, but highly demanded in many industrial sectors, as automotive, cosmetics, plastics for consumer electronics, printing inks, architectural coatings, etc. It is necessary to control complex instrumentation and to do visual assessments of texture and color differences to get, for instance, a visual harmony in car bodies; and a profound knowledge of physics and chemistry of special-effect pigments for their optical formulation to obtain attractive visual effects in coatings, plastics, etc, combining among them and with solid pigments. From University of Alicante, for the academic year 2013-14, we are organizing the first MSc degree in Color Technology for the Automotive Sector, with a design of contents embracing CIE colorimetry and visual perception, included the AUDI2000 color difference formula, instrumentation and color management software, fundamentals of coatings and plastics in the automotive sector, and, optical formulation of pigments. The MSc syllabus, with 60 ECTS, is designed to be taught in two semesters: from September to February with on classroom theoretical and practical activities, and, from March to June at virtual level, with internships of training in some companies. Therefore, the MSc Thesis would be the performance report during the internship in companies or research institutions. Some multinational companies, both as car makers and coatings and plastics providers, from European and non-European countries have already shown their support and interest in welcoming students for specific training, even some job offers when the first MSc edition finishes.

  17. Air management system for automotive fuel cells; Luftversorgungssystem fuer Fahrzeugbrennstoffzellen

    Energy Technology Data Exchange (ETDEWEB)

    Kauder, K.; Temming, J. [Dortmund Univ. (Germany). Fachgebiet Fluidenergiemaschinen

    2001-07-01

    Fuel cells have attained a predominant position in the development of alternative automotive drives during the last few years. The Polymer Electrolyte Membrane Fuel Cell (PEMFC), preferred for automotive applications, requires compressed air for maximum efficiency. In most prototypes this is provided by twin-screw compressors. The article introduces the different types of fuel cells, and the system and requirements of mobile applications of fuel cells. The advantages and development potential of screw compressors are described. Furthermore concepts of a compressor-expander module based on screw machines are presented and discussed. (orig.) [German] Bei der Entwicklung alternativer Fahrzeugantriebe hat die Brennstoffzelle in den letzten Jahren eine vorherrschende Stellung eingenommen. Die Polymer-Elektrolyt-Membran Brennstoffzelle, PEMFC, die fuer automotive Anwendungen bevorzugt verwendet wird, benoetigt fuer einen optimalen Wirkungsgrad eine Druckluftversorgung. Als Compressor kommt derzeit insbesondere der Schraubenlader bzw. -compressor in verschiedenen Prototypenfahrzeugen zum Einsatz. Der Beitrag behandelt zunaechst die unterschiedlichen Brennstoffzellentypen, den Systemaufbau und die Anforderungen an die mobile Anwendung der Brennstoffzelle. Fuer diesen speziellen Anwendungsfall werden Vorteile und Entwicklungsmoeglichkeiten der Schraubenmaschine dargelegt. Davon ausgehend finden sich Konzepte zum Aufbau eines Compressor-Expander-Moduls (CEM) auf Basis der Schraubenmaschinen. (orig.)

  18. Fast automotive diesel exhaust measurement using quantum cascade lasers

    Science.gov (United States)

    Herbst, J.; Brunner, R.; Lambrecht, A.

    2013-12-01

    Step by step, US and European legislations enforce the further reduction of atmospheric pollution caused by automotive exhaust emissions. This is pushing automotive development worldwide. Fuel efficient diesel engines with SCRtechnology can impede NO2-emission by reduction with NH3 down to the ppm range. To meet the very low emission limits of the Euro6 resp. US NLEV (National Low Emission Vehicle) regulations, automotive manufacturers have to optimize continuously all phases of engine operation and corresponding catalytic converters. Especially nonstationary operation holds a high potential for optimizing gasoline consumption and further reducing of pollutant emissions. Test equipment has to cope with demanding sensitivity and speed requirements. In the past Fraunhofer IPM has developed a fast emission analyzer called DEGAS (Dynamic Exhaust Gas Analyzer System), based on cryogenically cooled lead salt lasers. These systems have been used at Volkswagen AG`s test benches for a decade. Recently, IPM has developed DEGAS-Next which is based on cw quantum cascade lasers and thermoelectrically cooled detectors. The system is capable to measure three gas components (i.e. NO, NO2, NH3) in two channels with a time resolution of 20 ms and 1 ppm detection limits. We shall present test data and a comparison with fast FTIR measurements.

  19. Accelerated testing of an optimized closing system for automotive fuel tank

    Science.gov (United States)

    Gligor, A.; Ilie, S.; Nicolae, V.; Mitran, G.

    2015-11-01

    Taking into account the legal prescriptions which are in force and the new regulatory requirements that will be mandatory to implement in the near future regarding testing characteristics of automotive fuel tanks, resulted the necessity to develop a new testing methodology which allows to estimate the behaviour of the closing system of automotive fuel tank over a long period of time (10-15 years). Thus, were designed and conducted accelerated tests under extreme assembling and testing conditions (high values for initial tightening torques, extreme values of temperature and pressure). In this paper are presented two of durability tests which were performed on an optimized closing system of fuel tank: (i) the test of exposure to temperature with cyclical variation and (ii) the test of continuous exposure to elevated temperature. In these experimental tests have been used main components of the closing system manufactured of two materials variants, both based on the polyoxymethylene, material that provides higher mechanical stiffness and strength in a wide temperature range, as well as showing increased resistance to the action of chemical agents and fuels. The tested sample included a total of 16 optimized locking systems, 8 of each of 2 versions of material. Over deploying the experiments were determined various parameters such as: the initial tightening torque, the tightening torque at different time points during measurements, the residual tightening torque, defects occurred in the system components (fissures, cracks, ruptures), the sealing conditions of system at the beginning and at the end of test. Based on obtained data were plotted the time evolution diagrams of considered parameter (the residual tightening torque of the system consisting of locking nut and threaded ring), in different temperature conditions, becoming possible to make pertinent assessments on the choice between the two types of materials. By conducting these tests and interpreting the

  20. The application of computer-aided technologies in automotive styling design

    Science.gov (United States)

    Zheng, Ze-feng; Zhang, Ji; Zheng, Ying

    2012-04-01

    In automotive industry, outline design is its life and creative design is its soul indeed. Computer-aided technology has been widely used in the automotive industry and more and more attention has been paid. This paper chiefly introduce the application of computer-aided technologies including CAD, CAM and CAE, analyses the process of automotive structural design and describe the development tendency of computer-aided design.

  1. Collaborative Assessment of the Automotive Sales Service Based on Co-Entropy

    Directory of Open Access Journals (Sweden)

    Dingfu Jiang

    2013-04-01

    Full Text Available Co-entropy function was constructed based on dissipative structure, collaboration and entropy theory, while co-entropy of each management level in automotive sales service and the mathematical quantified assessment model of collaborative efficiency were built. In combination with the collaborative management activity of automotive sales service in an automotive sales company in Shanghai, the model and viewpoints presented here were applied and verified through empirical research.

  2. Business Case for Online Marketing of Automotive Financing for First West Credit Union

    OpenAIRE

    Sidhu, Amerpreet

    2012-01-01

    This project develops user experience and online marketing strategies for the growth of First West Credit Union, the third largest Credit Union in British Columbia. Several recommendations focus on the Automotive Financing Division of First West Credit Union. The project researches user needs in the automotive finance sector, analyzes operational forces and recommends strategies that affect business operations, customer service, online brand awareness and system usability. Automotive dealersh...

  3. The status of ceramic turbine component fabrication and quality assurance relevant to automotive turbine needs

    Energy Technology Data Exchange (ETDEWEB)

    Richerson, D.W.

    2000-02-01

    This report documents a study funded by the U.S. Department of Energy (DOE) Office of Transportation Technologies (OTT) with guidance from the Ceramics Division of the United States Automotive Materials Partnership (USAMP). DOE and the automotive companies have funded extensive development of ceramic materials for automotive gas turbine components, the most recent effort being under the Partnership for a New Generation of Vehicles (PNGV) program.

  4. Analyzing internal barriers for automotive parts remanufacturers in China using grey-DEMATEL approach

    DEFF Research Database (Denmark)

    Xia, Xiqiang; Govindan, Kannan; Zhu, Qinghua

    2015-01-01

    Automotive industries have attracted attention from international sectors recently. This attention to the industry results in many innovative technologies being integrated in these manufacturing arenas. In developing countries such as the BRIC (Brazil, Russia, India, and China) countries......, especially China who is a global leader in automotive sales and production, researchers see substantial attempts to increase economic and societal values in automotive sectors through the use of many sustainable strategies. Among these sustainable strategies, remanufacturing has witnessed much debate...

  5. Graduate Automotive Technology Education (GATE) Program: Center of Automotive Technology Excellence in Advanced Hybrid Vehicle Technology at West Virginia University

    Energy Technology Data Exchange (ETDEWEB)

    Nigle N. Clark

    2006-12-31

    This report summarizes the technical and educational achievements of the Graduate Automotive Technology Education (GATE) Center at West Virginia University (WVU), which was created to emphasize Advanced Hybrid Vehicle Technology. The Center has supported the graduate studies of 17 students in the Department of Mechanical and Aerospace Engineering and the Lane Department of Computer Science and Electrical Engineering. These students have addressed topics such as hybrid modeling, construction of a hybrid sport utility vehicle (in conjunction with the FutureTruck program), a MEMS-based sensor, on-board data acquisition for hybrid design optimization, linear engine design and engine emissions. Courses have been developed in Hybrid Vehicle Design, Mobile Source Powerplants, Advanced Vehicle Propulsion, Power Electronics for Automotive Applications and Sensors for Automotive Applications, and have been responsible for 396 hours of graduate student coursework. The GATE program also enhanced the WVU participation in the U.S. Department of Energy Student Design Competitions, in particular FutureTruck and Challenge X. The GATE support for hybrid vehicle technology enhanced understanding of hybrid vehicle design and testing at WVU and encouraged the development of a research agenda in heavy-duty hybrid vehicles. As a result, WVU has now completed three programs in hybrid transit bus emissions characterization, and WVU faculty are leading the Transportation Research Board effort to define life cycle costs for hybrid transit buses. Research and enrollment records show that approximately 100 graduate students have benefited substantially from the hybrid vehicle GATE program at WVU.

  6. 假茎回收式香蕉茎叶粉碎机的设计%The Development of Recycling Type Banana Leaf Shredder

    Institute of Scientific and Technical Information of China (English)

    李金燐; 张喜瑞; 李粤; 梁栋

    2016-01-01

    Banana straw contains high nutrition , if recycling will be a huge plant resources , current domestic develop-ment of banana stalk shredder mostly straw shattered after returning directly , and the little research that is shattered after the recycling machine .Aiming at this problem , we design a false stem recycling type crusher , banana leaf describes the overall design of the machine and structure of the main components .This machine is divided into false stem shattered in-stitutions and two parts in crushing mechanism , is mainly composed of a cutting device , spiral rotary device , double disc type false stem cutting device , lifting device , transmission device , fake stem crushing device , transmission channel , blade grinding device and banana straw debris collection device and so on , banana stem shattered , stem fragments recov-ery, in crushing counters-field set in one body .This machine design for the banana leaf resource utilization equipment research and development provides a feasible new models , for subsequent processing of banana false stem use reserve the necessary technology .%香蕉假茎含有较高的营养成分,若回收利用将是一种巨大的植物资源。目前,国内研制的香蕉秸秆粉碎机大多为假茎粉碎后直接还田,而对其粉碎后回收的机器研究很少。为此,设计了一种假茎回收式香蕉茎叶粉碎机,确定了其总体设计方案及主要部件的结构。该机分为假茎粉碎机构和蕉叶粉碎机构两部分,主要由切稍装置、螺旋扶茎装置、双圆盘式假茎切断装置、升降装置、传送装置、假茎粉碎装置、输送通道、叶片粉碎装置和假茎碎片收集装置等组成,将香蕉假茎粉碎、假茎碎片回收及蕉叶粉碎还田集于一体。该机的设计为香蕉茎叶资源利用设备的研发提供了可行的新型机型,为后续香蕉假茎的深加工利用储备了必要的技术。

  7. The Design of a Multi-purpose Branch Shredder Model QCF50%QCF50型多用枝条粉碎机的设计

    Institute of Scientific and Technical Information of China (English)

    胡祚忠; 刘泽生; 钟承祥; 张剑飞; 吴建梅; 陈智毅; 叶晶晶

    2011-01-01

    基于为桑枝食用菌基料大规模生产中的枝条粉碎提供高效、安全、实用机具的目的,参照国家及部颁标准进行标准化设计,设计并研制出QCF50型多用枝条粉碎机.该机的基本结构由架体、动力、工作部件3个部分组成,将切、碎、筛3个加工过程集于一体,从传动、进料、物料粉碎到出料都在安全防护下进行.通过对该机主要技术参数的设计与计算,合理选用材料、配置主轴转速及采用适应不同原料加工的筛板,使样机的性能可靠、运行安全.样机用于植物枝条粉碎加工的生产效率达到1000 kg/h,用于园木棒材粉碎加工的生产效率为1500 kg/h,粉碎的物料达到食用菌培育基料的质量要求.%In order to provide an efficient, safe and practical machinery for shredding mulberry branches in large scale production of base materials for raising edible fungi, we designed and developed a multi-purpose branch shredder Model QCF50 with standardized designing in accordance with the standards stipulated by the nation and the ministry. This machine is composed of a frame, an engine and other work pieces. It integrates cutting, crushing and sieving processes in its operation. The transmission and material feeding, manufacturing and discharging are all run under safeguard condition. Through designing and computing major technical parameters, selecting adequate material, configuring rotation speed of the main shaft, and using different sieve plates for different shredding purposes, performance of the machine is reliable and safe. The productivity of the sample machine reached 1 000 kg/h when branches were processed and was 1 500 kg/h when round logs and wood bars were processed. And the shredded material reached the quality requirement of base material for raising edible fungi.

  8. Design of Single Ridge Sweet Potato Vine Shredder%单垄红薯薯藤切碎机的设计

    Institute of Scientific and Technical Information of China (English)

    申屠留芳; 巩尊国; 宗林新; 孙星钊; 孙成龙

    2014-01-01

    红薯味道甜美,富含碳水化合物、膳食纤维、胡萝卜素、维生素以及钾、镁、铜、硒、钙等10余种元素,其营养价值和养生保健作用很大。因此,红薯在世界各地是很多人喜欢的食物,近年来得到广泛的种植,因此红薯收割机器有着广阔的市场前景。藤蔓的处理是红薯收割的主要组成部分,人工切除耗时耗力,并且不能达到切碎的效果。红薯薯藤切碎机的设计能很好地将藤蔓切割、切碎且回归田地,使红薯藤的处理方便快捷,可增加土壤有机质,达到农业生产节本增效的目的。%Sweet potato taste sweet , rich in carbohydrates , dietary fiber , carotene , vitamins and potassium , magnesium , copper, selenium, calcium and so on more than 10 kinds of elements, the sweet potato is small, its nutritional value and health care function is great .Therefore , the sweet potato is a lot of people like the food in the world , in recent years more and more widely planted , so can harvest sweet potatoes machine has broad market prospects. The vine treatment is the main part of the sweet potato harvest , artificial excision and time-consuming , and cannot achieve the shredding effect .Design of sweet potato vine shredder can be chopped vines cut and return to field , the processing of sweet potato vine is convenient , at the same time , increase soil organic matter , to realize the agricultural production cost saving pur-pose .

  9. 汽车物流浅谈%Automotive Logistics

    Institute of Scientific and Technical Information of China (English)

    刘大顺; 张迎杰; 赫立远

    2016-01-01

    With the improvement of people's living standards, more and more diversified way to travel, private cars as a way to travel in recent years, demand is also rising, showing a clear upward trend. In recent years through cooperating with imported brand car enterprises, coupled with the country strongly support, making own-brand car companies have significantly improved the technical level ,meanwhile gradually narrowing the gap with the joint ventures in terms of quality and performance etc. But an important issue can not be ignored is the cost control.We still can not effectively reduce production costs, resulting in own-brand car companies can not compete with the joint venture brand in the price, and automotive logistics cost is the most important part of the production costs.The so-called automotive logistics, refers to the entity flow process of the raw materials,components,vehicle and aftermarket parts in the various links on automotive supply chain.Generalized automotive logistics also include the recovery of part of the scrap cars. Automotive Logistics play a role of bridge and tie in the automotive industry chain. Automotive Logistics is the fundamental guarantee to achieve the smooth flow of the value of the automobile industry. So how can we effectively control the automotive logistics costs, has become an inevitable study subject of China's auto industry development process. The following, use the independent brand Brilliance Automotive as an example, and provide a detailed description of the automotive present development situation and logistics problems,provide appropriate referenced solutions.%随着人们生活水平的日益提高,出行方式也越来越多元化,私家车作为出行方式的一种,近年来需求量也水涨船高,呈现一个明显上升趋势。近些年自主品牌汽车通过与进口品牌车企的合作、再加上国家对自主品牌车企的大力扶持,使自主品牌车企技术水平有明显的提升,同时

  10. Cold start dynamics and temperature sliding observer design of an automotive SOFC APU

    Science.gov (United States)

    Lin, Po-Hsu; Hong, Che-Wun

    This paper presents a dynamic model for studying the cold start dynamics and observer design of an auxiliary power unit (APU) for automotive applications. The APU is embedded with a solid oxide fuel cell (SOFC) stack which is a quiet and pollutant-free electric generator; however, it suffers from slow start problem from ambient conditions. The SOFC APU system equips with an after-burner to accelerate the start-up transient in this research. The combustion chamber burns the residual fuel (and air) left from the SOFC to raise the exhaust temperature to preheat the SOFC stack through an energy recovery unit. Since thermal effect is the dominant factor that influences the SOFC transient and steady performance, a nonlinear real-time sliding observer for stack temperature was implemented into the system dynamics to monitor the temperature variation for future controller design. The simulation results show that a 100 W APU system in this research takes about 2 min (in theory) for start-up without considering the thermal limitation of the cell fracture.

  11. Effect of Titanium on the Mechanical Properties and Microstructure of Gray Cast Iron for Automotive Applications

    Science.gov (United States)

    Gelfi, M.; Gorini, D.; Pola, A.; La Vecchia, G. M.

    2016-09-01

    Lamellar gray cast iron, with a mainly pearlitic microstructure, is widely used in the automotive industry, mostly in the manufacturing of brake disks. This work analyzes in depth the effects of small variations of titanium content on the microstructure and mechanical properties of cast iron brake disks. For this purpose, eight different heats of EN-GJL-250 cast iron were selected, with a similar chemical composition but with different titanium contents, varying from 0.013 to 0.031%. The drops in mechanical strength and hardness values measured on the high-Ti samples were correlated to microstructural variations quantitatively observed by means of optical and scanning electron microscope. It was found that titanium combines to form titanium nitrides, suppressing the beneficial microstructural effects of nitrogen at solidification. Residual nitrogen, if present in sufficient quantity, promotes the nucleation of primary austenite from the liquid and the formation of a fine microstructure, with small eutectic cells and lower graphite content. Such a microstructure provides brake disks with better mechanical properties. The interpretation of results was further supported by thermal analysis and thermodynamic calculations.

  12. Electrohydraulic Forming of Near-Net Shape Automotive Panels

    Energy Technology Data Exchange (ETDEWEB)

    Golovaschenko, Sergey F.

    2013-09-26

    The objective of this project was to develop the electrohydraulic forming (EHF) process as a near-net shape automotive panel manufacturing technology that simultaneously reduces the energy embedded in vehicles and the energy consumed while producing automotive structures. Pulsed pressure is created via a shockwave generated by the discharge of high voltage capacitors through a pair of electrodes in a liquid-filled chamber. The shockwave in the liquid initiated by the expansion of the plasma channel formed between two electrodes propagates towards the blank and causes the blank to be deformed into a one-sided die cavity. The numerical model of the EHF process was validated experimentally and was successfully applied to the design of the electrode system and to a multi-electrode EHF chamber for full scale validation of the process. The numerical model was able to predict stresses in the dies during pulsed forming and was validated by the experimental study of the die insert failure mode for corner filling operations. The electrohydraulic forming process and its major subsystems, including durable electrodes, an EHF chamber, a water/air management system, a pulse generator and integrated process controls, were validated to be capable to operate in a fully automated, computer controlled mode for forming of a portion of a full-scale sheet metal component in laboratory conditions. Additionally, the novel processes of electrohydraulic trimming and electrohydraulic calibration were demonstrated at a reduced-scale component level. Furthermore, a hybrid process combining conventional stamping with EHF was demonstrated as a laboratory process for a full-scale automotive panel formed out of AHSS material. The economic feasibility of the developed EHF processes was defined by developing a cost model of the EHF process in comparison to the conventional stamping process.

  13. Composites on the way to structural automotive applications

    Energy Technology Data Exchange (ETDEWEB)

    Friedrich, H.; Kopp, J.; Stieg, J. [Volkswagen AG, Wolfsburg (Germany)

    2003-07-01

    Against the background of a steady increase of the standards on comfort, passive safety and driving performance of vehicles as well as the commitment to reduce fuel consumption and carbon dioxide emissions, the demand for lightweight construction attains paramount importance. The use of aluminum, magnesium or new steel alloys in the body structure can lead to significant weight reduction compared with conventional steel concepts. Furthermore, maximum weight reduction will require an intensive use of advanced composites in primary structures. The paper deals with the potentials and the challenges coming along with the introduction of advanced composites into automotive series production. Presently, liquid composite molding and compression molding of high-performance SMC are the most promising technologies to achieve demanding composite parts with high fiber volume fraction, good surface quality and controlled mechanical properties. The performance of specific automotive application processed in these techniques is presented and discussed. On principle, the cost/benefit aspect is of decisive importance for larger volume applications. Considerable efforts are necessary to reduce material and semi-finished product costs and to provide manufacturing technologies which are capable of allowing large-volume automotive production of composite components. Especially concepts are desirable which do not only provide a basic material substitution but rather an intelligent design based on component and functional integration as one of the most effective strategies to exploit the advantages of advanced composites. These aspects will be regarded and a brief summary on some other remaining challenges like recycling, crash simulation or joining and assembly technologies for mixed material concepts will be given. (orig.)

  14. Model-based diagnosis through Structural Analysis and Causal Computation for automotive Polymer Electrolyte Membrane Fuel Cell systems

    Science.gov (United States)

    Polverino, Pierpaolo; Frisk, Erik; Jung, Daniel; Krysander, Mattias; Pianese, Cesare

    2017-07-01

    The present paper proposes an advanced approach for Polymer Electrolyte Membrane Fuel Cell (PEMFC) systems fault detection and isolation through a model-based diagnostic algorithm. The considered algorithm is developed upon a lumped parameter model simulating a whole PEMFC system oriented towards automotive applications. This model is inspired by other models available in the literature, with further attention to stack thermal dynamics and water management. The developed model is analysed by means of Structural Analysis, to identify the correlations among involved physical variables, defined equations and a set of faults which may occur in the system (related to both auxiliary components malfunctions and stack degradation phenomena). Residual generators are designed by means of Causal Computation analysis and the maximum theoretical fault isolability, achievable with a minimal number of installed sensors, is investigated. The achieved results proved the capability of the algorithm to theoretically detect and isolate almost all faults with the only use of stack voltage and temperature sensors, with significant advantages from an industrial point of view. The effective fault isolability is proved through fault simulations at a specific fault magnitude with an advanced residual evaluation technique, to consider quantitative residual deviations from normal conditions and achieve univocal fault isolation.

  15. 48 CFR 1852.223-76 - Federal Automotive Statistical Tool Reporting.

    Science.gov (United States)

    2010-10-01

    ... Statistical Tool Reporting. 1852.223-76 Section 1852.223-76 Federal Acquisition Regulations System NATIONAL... Provisions and Clauses 1852.223-76 Federal Automotive Statistical Tool Reporting. As prescribed at 1823.271 and 1851.205, insert the following clause: Federal Automotive Statistical Tool Reporting (JUL 2003) If...

  16. 77 FR 19000 - Foreign-Trade Zone 99-Wilmington, DE: Application for Manufacturing Authority; Fisker Automotive...

    Science.gov (United States)

    2012-03-29

    ... and flanges, chain, heat exchangers, spray nozzles, universal joints, clutches, half/drive shafts... 99--Wilmington, DE: Application for Manufacturing Authority; Fisker Automotive, Inc. (Electric... authority on behalf of Fisker Automotive, Inc. (Fisker), to manufacture electric-powered, light-duty...

  17. Equipment for testing automotive lead/acid batteries under SAE J240a conditions

    Science.gov (United States)

    Hamilton, J. A.; Rand, D. A. J.

    Battery cycling equipment has been designed and constructed to test lead/acid batteries according to the American Society of Automotive Engineers' (SAE) J240a Standard. This life test simulates automotive service where the battery operates in a voltage-regulated charging system. The CSIRO design uses a master/slave concept to reduce both construction time and cost.

  18. Building Competitive Advantages CEIBS Holds the 2004 CEIBS China Automotive Industry Forum

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ Second consecutive CEIBS China Automotive Industry Forum was held in Novermber 22 at the school's Shang hai campus. Following last year's success, this year there are more than 200 local and international participants including: auto manufacturers, component suppliers, government officials, industry experts and researchers, who have gathered today to discuss issues in the country's automotive industry.

  19. 38 CFR 17.155 - Minimum standards of safety and quality for automotive adaptive equipment.

    Science.gov (United States)

    2010-07-01

    ... safety and quality for automotive adaptive equipment. 17.155 Section 17.155 Pensions, Bonuses, and... Minimum standards of safety and quality for automotive adaptive equipment. (a) The Under Secretary for Health or designee is authorized to develop and establish minimum standards of safety and quality for...

  20. RECYCLED TEXTILES USED IN AUTOMOTIVE INTERIORS. CASE STUDY- FORD MOTOR COMPANY

    Directory of Open Access Journals (Sweden)

    CUC Sunhilde

    2017-05-01

    Full Text Available The environmental movement is affecting all industries, but the textile and automotive industries are two of the few that are constantly being criticized. The automotive industry is the subject of much research, it is the largest manufacturing activity, there is a complex supply chain, is resource intensive and emits various hazardous gases and waste products. The article reviews the current state of automotive industry regarding the textile application. Automotive textiles have been classified as belonging to a category called “Mobiltech” which is one of the main streams of technical textiles. The term means all type of textile components e.g. fibers, filaments, yarns and the fabric used in automobiles. They are classed as technical textile because of the very high performance specifications and special properties required, different from those used in clothing and other applications. The performance of the automotive textiles depends on the fibre properties, fabric structures and various finishes used in the manufacturing processes. After a short presentation of used fibres in car interiors, with advantages and disadvantages it is presented the sustainable textile solutions for the automotive industry. The paper focuses in particular of the use of recycling of textile waste to highlight how the processes of recycled textiles and sustainable textiles production are linked in the automotive sector. A case study with Ford Motor Company outlines and examines their design, development and manufacture process for automotive textiles for car seat coverings and interiors

  1. 75 FR 28303 - Setco Automotive, Inc., Paris, TN; Notice of Revised Determination on Reconsideration

    Science.gov (United States)

    2010-05-20

    ... Notice of determination was published in the Federal Register on April 23, 2010 (FR 75 21358). The... Employment and Training Administration Setco Automotive, Inc., Paris, TN; Notice of Revised Determination on... reconsideration, I determine that workers of Setco Automotive, Inc., Paris, Tennessee meet the worker...

  2. Characterization of process air emissions in automotive production plants.

    Science.gov (United States)

    D'Arcy, J B; Dasch, J M; Gundrum, A B; Rivera, J L; Johnson, J H; Carlson, D H; Sutherland, J W

    2016-01-01

    During manufacturing, particles produced from industrial processes become airborne. These airborne emissions represent a challenge from an industrial hygiene and environmental standpoint. A study was undertaken to characterize the particles associated with a variety of manufacturing processes found in the auto industry. Air particulates were collected in five automotive plants covering ten manufacturing processes in the areas of casting, machining, heat treatment and assembly. Collection procedures provided information on air concentration, size distribution, and chemical composition of the airborne particulate matter for each process and insight into the physical and chemical processes that created those particles.

  3. Change in the automotive industry; Fordonsindustrin i foeraendring

    Energy Technology Data Exchange (ETDEWEB)

    Fjaellstroem, Mikael [Swedish Energy Agency, Eskilstuna (Sweden); Pohl, Hans [Sycon Energikonsult AB, Malmoe (Sweden); Liljemark, Stefan [SwedPower AB (Sweden); Leander, Aasa [Swedish Energy Agency, Eskilstuna (Sweden); Maruo, Kanehira [Chalmers Univ. of Tech., Goeteborg (Sweden); Waldenby, Torbjoern [JIC Consulting AB, Goeteborg (Sweden); Mellgren, Henry [Fordonskomponentgruppen, Goeteborg (Sweden)

    2002-04-01

    The 'Change in the Automotive Industry' investigation was initiated by the Swedish Energy Agency in the autumn of 2000. The objective has been to illuminate and analyse technical developments in respect of the use of electricity in vehicles, not only for various ancillary systems but also for propulsion. A number of Swedish businesses that have, or could have, links with the automotive industry have been investigated. The main aim has been to attempt to identify the opportunities for the industry to meet and benefit from the changes. A total of 14 businesses have been visited, and a further 29 companies have replied to a survey questionnaire on the theme. Business intelligence shows that a great deal of work is being done on the use of electricity for automotive propulsion, in everything from battery vehicles, via electric hybrid vehicles to fuel cell vehicles. In terms of development, the Japanese manufacturers are in the lead, while the USA constitutes the largest single driving force behind development. The technical development requires a greater understanding within several new disciplines, and leads to major changes between different industry sectors. The results show that Sweden possesses world class expertise in several of the fields that can become very important for tomorrow's automotive industry. At the same time, the companies expect difficulties in recruiting personnel qualified in the appropriate disciplines, such as development and design. There is, therefore, a clear risk that the present-day expertise will progressively fade away if nothing is done.There is a wide range of awareness of the greater use of electricity in vehicles. However, in principle, all companies feel that development towards new drive trains will proceed rapidly. Most of the companies are also very interested in descriptions and analyses of the state of development. The general conclusion of the work is that there are excellent prospects for Swedish industry to

  4. A model to assess the comfort of automotive seat cushions.

    Science.gov (United States)

    Jiaxing, Zhan; Fard, Mohammad; Jazar, Reza

    2014-01-01

    A large number of independent and interacting factors affect seating comfort such as seat shape, stability, lumbar support and seat height. Although many subjective comfort studies have been conducted, few of them considered seating comfort from its subassembly level. This paper analyzed the automotive seat cushion designed with geared four-bar linkage for the seat height adjustment. The operation torque and lift distance of this mechanism was investigated as 2 major comfort factors. Ten cushions with this kind of design in the market were compared and assessed.

  5. Control of an Automotive Semi-Active Suspension

    Directory of Open Access Journals (Sweden)

    Jorge de Jesús Lozoya-Santos

    2012-01-01

    Full Text Available Two controllers for an automotive suspensions with Magneto-Rheological (MR dampers are proposed. One is a model-based using the Linear Parameter Varying (LPV approach, and the other is a model-free controller with a Frequency Estimation Based (FEB principle. The LPV controller includes an experimental nonlinear model of an MR damper using only one scheduling parameter. A comparison with a several semiactive controllers for comfort and road holding is discussed. The FEB controller is the best option based on frequency and time response analysis for comfort (10–20%, suspension deflection (30–50%, and road holding (1–5%.

  6. Trends in the automotive paint industry for corrosion protection

    Energy Technology Data Exchange (ETDEWEB)

    Blandin, Nathalie; Brunat, William [PPG Industries France, 3 Z.A.E. Les Dix Muids, B.P. 89, F-59583 Marly (France); Neuhaus, Ralf [PPG Industries Lacke GmbH, Stackenbergstrasse 34, D-42329 Wuppertal (Germany); Sibille, Ettore [PPG Industries Italia, Via Serra11, I-15028 Quattordio (Italy)

    2004-07-01

    Since many years ED-paints are protecting car bodies against corrosion. Currently the automotive paint industry is faced with increasing demands of higher levels of corrosion protection and also requests to comply with new environmental regulations and economical pressures. Some key factors that contributed significantly towards the improvement of corrosion protection systems are: - New generations of lead free ED-paints; - Weldable organic thin film for corrosion protection, especially in box cavities and flange areas. The goal of this paper is to show how the various elements of the 'anti-corrosion package' interact. (authors)

  7. Stock Control in Automotive Industry with Simulation Utilization

    Directory of Open Access Journals (Sweden)

    Petra Vegnerová

    2008-12-01

    Full Text Available At this time in economic environment there is the big trend of coming logistical chain, supply chain and supply chain management (SCM. SCM deals with material and information flows control, inventory management, demand forecast, production plan optimalization, distribution management etc. Nowadays for effective purchase, production and distribution plan and control in companies are utilized the simulation and simulation programmes. This paper deals with the simulation programme Witness and its utilization for finding of results real problems – simulation utilization for stocks solution in automotive industry. The model can be used for the determination of new delivery system of materials and for stocks reduction.

  8. Broadening the Concept of Poka Yoke Beyond Automotive Industry

    Science.gov (United States)

    Măgdoiu, Alex; Oprean, Constantin

    2014-12-01

    This paper will present the development of the poka yoke systems, which were initially created and implemented just for the automotive industry, also to other domains. For some fields like medicine, constructions or software development there are already articles available on the benefits brought by poka yoke systems' implementation. Besides these domains the article will contribute to the recognition of poka yoke systems in fields where, although error proofing systems are used, no link to the poka yoke method was made by the authors, creators and users

  9. AUTOMOTIVE MAINTENANCE PLAN IMPROVEMENT BASED ON DISTRIBUTION OF FAILURE TIMES

    Directory of Open Access Journals (Sweden)

    Alexandru BOROIU

    2016-05-01

    Full Text Available In accordance with the concept of "RCM - Reliability Centered Maintenance", the paper presents a study on the possibility to improve maintenance plan for the most frequently replaced parts from a sample of cars, followed during the operation period: front/rear brake pads. After analyzing the reliability of these components, it is found that there is the possibility of introducing the obligatory replacement operation of brake pads who have reached the third technical inspection without being replaced, sacrificing resource exploitation of them, but improving the benefits for the client - the automotive availability.

  10. Coordinating mecanisms in automotive distribution channel: distinctive elements

    Directory of Open Access Journals (Sweden)

    Heloisa Sousa Ribeiro Ferreira

    2011-09-01

    Full Text Available Besides managing its internal activities, the supply chain management has the challenge of coordinating and managing its partners. The references indicate some organizational and management tools that can help in performing those activities, and in this paper, they are called Supply Chain Coordinating Practices. This paper identifies and evaluates the results obtained by applying some coordinating practices o in the Brazilian automotive channel distribution. This article is an exploratory study, using one case study as research method. The result shows that all of the related practices are presented in the Relationships analysed. However, regarding the benefits obtained, industry and distributors have different opinions.

  11. Automotive Dealerships & Garages: Digital Transformation to Increase Operational Efficiency

    OpenAIRE

    Anamaya

    2016-01-01

    The digital wave has taken the automotive industry by storm. It has brought about dramatic changes in the way the automobile industry has been perceived. Today one can access the car’s dashboard through their phone, Google has come up with driver-less cars and Tesla has disrupted technology innovation to go beyond just electric cars. Customers of the present day too have embraced these changes and are better equipped to understand and compare the various features and benefits of each automobi...

  12. Optimal Design of Automotive Thermoelectric Air Conditioner (TEAC)

    Science.gov (United States)

    Attar, Alaa; Lee, HoSung; Weera, Sean

    2014-06-01

    The present work is an analytical study of the optimal design of an automotive thermoelectric air conditioner (TEAC) using a new optimal design method with dimensional analysis that has been recently developed by our research group. The optimal design gives not only the optimal current but also the optimal geometry (i.e., the number of thermocouples, the geometric factor, or the hot fluid parameters). The optimal design for the TEAC is carried out with two configurations: air-to-liquid and air-to-air heat exchangers.

  13. Influences of weather phenomena on automotive laser radar systems

    Science.gov (United States)

    Rasshofer, R. H.; Spies, M.; Spies, H.

    2011-07-01

    Laser radar (lidar) sensors provide outstanding angular resolution along with highly accurate range measurements and thus they were proposed as a part of a high performance perception system for advanced driver assistant functions. Based on optical signal transmission and reception, laser radar systems are influenced by weather phenomena. This work provides an overview on the different physical principles responsible for laser radar signal disturbance and theoretical investigations for estimation of their influence. Finally, the transmission models are applied for signal generation in a newly developed laser radar target simulator providing - to our knowledge - worldwide first HIL test capability for automotive laser radar systems.

  14. Part Transportation Improvement in Warehouse of an Automotive Factory

    Science.gov (United States)

    Choojan, Tiwapom; Chutima, Parames

    2016-05-01

    This research is focus on the problems cause the assembly line stop in a Japanese automotive manufacturer in Thailand. The problem arose from not being able to supply parts to the assembly line in time and supplying wrong parts to the assembly line. Methods to resolve these problems involved the followings: 1) design new tag labels, 2) improve operations method and 3) redesign the parts storage layout and supply routes. The result showed that the time for transferring parts from the warehouse to the preparing area and the overlapped routes were reduced. Moreover, the supply accuracy from the preparation area to the assembly line was improved.

  15. Manufacturing Aspects of Advanced Polymer Composites for Automotive Applications

    Science.gov (United States)

    Friedrich, Klaus; Almajid, Abdulhakim A.

    2013-04-01

    Composite materials, in most cases fiber reinforced polymers, are nowadays used in many applications in which light weight and high specific modulus and strength are critical issues. The constituents of these materials and their special advantages relative to traditional materials are described in this paper. Further details are outlined regarding the present markets of polymer composites in Europe, and their special application in the automotive industry. In particular, the manufacturing of parts from thermoplastic as well as thermosetting, short and continuous fiber reinforced composites is emphasized.

  16. SOFTWARE AND HARDWARE DESIGN CHALLENGES IN AUTOMOTIVE EMBEDDED SYSTEM

    Directory of Open Access Journals (Sweden)

    Rajeshwari Hegde

    2011-10-01

    Full Text Available Modern automotives integrate large amount of electronic devices to improve the driving safety andcomfort. This growing number of Electronic Control Units (ECUs with sophisticated software escalatesthe vehicle system design complexity. In this paper we explain the complexity of ECUs in terms ofhardware and software and also we explore the possibility of Common Object Request Broker Architecture(CORBA architecture for the integration of add-on software in ECUs. This reduces the complexity of theembedded system in vehicles and eases the ECU integration by reducing the total number of ECUs in thevehicles.

  17. New microalloyed steel applications for the automotive sector

    Energy Technology Data Exchange (ETDEWEB)

    Matlock, D.K.; Krauss, G.; Speer, J.G. [Advanced Steel Processing and Products Research Center, Colorado School of Mines, Golden, CO (United States)

    2005-07-01

    Developments related to the use of microalloy additions, primarily of Ti, Nb, and V, and controlled processing are reviewed to illustrate how steels with tailored microstructures and properties are produced from either bar or sheet steels for new automotive components. Microalloying additions are shown to control the necessary strengthening mechanisms to produce high strength materials with the desired toughness or formability for a specific application. Selected examples of direct cooled forging steels, microalloyed carburizing steels, and advanced high strength sheet (AHSS) steels are discussed. (orig.)

  18. Simulation of Artificial Intelligence for Automotive Air-conditioning System

    Institute of Scientific and Technical Information of China (English)

    YUAN Xiao-mei; CHEN You-hua; CHEN Zhi-jiu

    2002-01-01

    The artificial intelligence is applied to the simulation of the automotive air-conditioning system ( AACS )According to the system's characteristics a model of AACS, based on neural network, is developed. Different control methods of AACS are discussed through simulation based on this model. The result shows that the neural- fuzzy control is the best one compared with the on-off control and conventional fuzzy control method.It can make the compartment's temperature descend rapidly to the designed temperature and the fluctuation is small.

  19. Sustainable business models and the automotive industry: A commentary

    Directory of Open Access Journals (Sweden)

    Peter Wells

    2013-12-01

    Full Text Available This commentary reviews the position articulated in an article published in 2004 that the business model prevalent in the automotive industry was inadequate to meeting the challenge of sustainability, and reviews the key developments since then. The most noticeable developments the commentary traces are the growth in academic interest in business models, a more responsive government policy particularly in respect of new technologies, and the practical application of the concepts and ideas mooted in the original paper, notably with respect to electric vehicles.

  20. Ultrapulse welding: A new joining technique. [for automotive industry

    Science.gov (United States)

    Anderson, D. G.

    1972-01-01

    The ultrapulse process is a resistance welding process that utilizes unidirectional current of high magnitude for a very short time with a precisely controlled dynamic force pulse. Peak currents of up to 220,000 amperes for two to ten milliseconds are used with synchronized force pulses of up to nine thousand pounds. The welding current passing through the relatively high resistance of the interface between the parts that are being joined results in highly localized heating. Described is the UPW process as it applies to the automotive industry.

  1. State Estimation in the Automotive SCR DeNOx Process

    DEFF Research Database (Denmark)

    Zhou, Guofeng; Jørgensen, John Bagterp; Duwig, Christophe;

    2012-01-01

    Selective catalytic reduction (SCR) of nitrogen oxides (NOx) is a widely applied diesel engine exhaust gas after-treatment technology. For effective NOx removal in a transient operating automotive application, controlled dosing of urea can be used to meet the increasingly restrictive legislations...... on exhaust gas emissions. For advanced control, e.g. Model Predictive Control (MPC), of the SCR process, accurate state estimates are needed. We investigate the performance of the ordinary and the extended Kalman filters based on a simple first principle system model. The performance is tested through...

  2. 76 FR 46852 - Workers From Kelly Services, Working On-Site at Delphi Automotive Systems, LLC, Powertrain...

    Science.gov (United States)

    2011-08-03

    ... workers from Kelly Services working on-site at Delphi Automotive Systems, LLC, El Paso, Texas. The workers...-site at Delphi Automotive Systems, LLC, Powertrain Division, El Paso, Texas. The amended notice...-site at Delphi Automotive Systems, LLC, Powertrain Division, El Paso, Texas, who became totally...

  3. A New Design Method of Automotive Electronic Real-time Control System

    Science.gov (United States)

    Zuo, Wenying; Li, Yinguo; Wang, Fengjuan; Hou, Xiaobo

    Structure and functionality of automotive electronic control system is becoming more and more complex. The traditional manual programming development mode to realize automotive electronic control system can't satisfy development needs. So, in order to meet diversity and speedability of development of real-time control system, combining model-based design approach and auto code generation technology, this paper proposed a new design method of automotive electronic control system based on Simulink/RTW. Fristly, design algorithms and build a control system model in Matlab/Simulink. Then generate embedded code automatically by RTW and achieve automotive real-time control system development in OSEK/VDX operating system environment. The new development mode can significantly shorten the development cycle of automotive electronic control system, improve program's portability, reusability and scalability and had certain practical value for the development of real-time control system.

  4. GB/T 21085-2007 Automotive Vehicle Certificate of Inspection

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    1.Background Automotive Vehicle Certificate of Inspection (hereinafter referred to certificate) is a statutory certificate for automotive vehicle registration in China and also an important content of consistency management of vehicle manufacturers.In order to strengthen the management of automotive vehicle manufacturers and their products,prevent stealing,smuggling and illegal assembling,crack down the illegal acts of forging and reselling and improve the efficiency of automotive vehicle registration,National Development and Reform Commission (NDRC) and MPS jointly put forward a solution that is to standardize the certificate and its content and build up information management system of certificates.The development of GB/T 21085-2007 Automotive Vehicle Certificate of Inspection was taken by the National Technical Committee of Auto Standardization (SAC/TC 114).

  5. Conceptual design study of an improved automotive gas turbine powertrain

    Science.gov (United States)

    Wagner, C. E. (Editor); Pampreen, R. C. (Editor)

    1979-01-01

    Automotive gas turbine concepts with significant technological advantages over the spark ignition (SI) engine were assessed. Possible design concepts were rated with respect to fuel economy and near-term application. A program plan which outlines the development of the improved gas turbine (IGT) concept that best met the goals and objectives of the study identifies the research and development work needed to meet the goal of entering a production engineering phase by 1983. The fuel economy goal is to show at least a 20% improvement over a conventional 1976 SI engine/vehicle system. On the basis of achieving the fuel economy goal, of overall suitability to mechanical design, and of automotive mass production cost, the powertrain selected was a single-shaft engine with a radial turbine and a continuously variable transmission (CVT). Design turbine inlet temperature was 1150 C. Reflecting near-term technology, the turbine rotor would be made of an advanced superalloy, and the transmission would be a hydromechanical CVT. With successful progress in long-lead R&D in ceramic technology and the belt-drive CVT, the turbine inlet temperature would be 1350 C to achieve near-maximum fuel economy.

  6. Exhaust gas energy recovery system of pneumatic driving automotive engine

    Institute of Scientific and Technical Information of China (English)

    Han Yongqiang; Sun Wenxu; Li Qinghua; Zhong Ming; Hao Wei; Du Wenchang

    2011-01-01

    Almost the same quantity to net output work of energy has been carried out and wasted by exhaust gas in typical automotive engine. Recovering the energy from exhaust gas and converting to mechanical energy will dramatically increase the heat efficiency and decrease the fuel consumption. With the increasing demand of fuel conservation, exhaust gas energy recovery technologies have been a hot topic. At present, many researches have been focused on heating or cooling the cab, mechanical energy using and thermo-electronic converting. Unfortunately, the complicated transmission of mechanical energy using and the depressed efficiency of thermo-electronic converting restrict their widely applying. In this paper, a kind of exhaust gas energy recovery system of pneumatic driving automotive engine, in which highly compressed air acts as energy storing and converting carrier, has been established. Pneumatic driving motor can produce moderate speed and high torque output, which is compatible for engine using. The feasibility has been certificated by GT-Power simulation and laboratory testes. The technologies about increasing recovery efficiency have been discussed in detail. The results demonstrated that the in parallel exhaust gas energy recovery system, which is similar to the compound turbo-charger structure can recovery 8 to 10 percent of rated power output. At last, a comprehensive system,which includes Rankine cycle based power wheel cycle unit etc. , has been introduced.

  7. On Mixed Flow Turbines for Automotive Turbocharger Applications

    Directory of Open Access Journals (Sweden)

    Bernhardt Lüddecke

    2012-01-01

    Full Text Available Due to increased demands for improved fuel economy of passenger cars, low-end and part-load performance is of key importance for the design of automotive turbocharger turbines. In an automotive drive cycle, a turbine which can extract more energy at high pressure ratios and lower rotational speeds is desirable. In the literature it is typically found that radial turbines provide peak efficiency at speed ratios of 0.7, but at high pressure ratios and low rotational speeds the blade speed ratio will be low and the rotor will experience high values of positive incidence at the inlet. Based on fundamental considerations, it is shown that mixed flow turbines offer substantial advantages for such applications. Moreover, to prove these considerations an experimental assessment of mixed flow turbine efficiency and optimal blade speed ratio is presented. This has been achieved using a new semi-unsteady measurement approach. Finally, evidence of the benefits of mixed flow turbine behaviour in engine operation is given. Regarding turbocharged engine simulation, the benefit of wide-ranging turbine map measurement data as well as the need for reasonable turbine map extrapolation is illustrated.

  8. USE OF NANOTECHNOLOGY PRE-TREATMENT IN AUTOMOTIVE PAINTING LINE

    Directory of Open Access Journals (Sweden)

    Alberto Nei Carvalho Costa

    2012-09-01

    Full Text Available The current safety requirements, environmental impacts and performance have been ledding the automotive industry to search for new alternatives, not just for new car bodies materials, also for new sheet surface treatments as well, used in the painting process in order to fit simultaneous, environmental requirements and corrosion resistance maintenance, that are the key feature guarantees offered by automakers and are also vital to the durability of the vehicle. This fact is of great importance considering that, besides the various types of steels and their metalic coatings, another factor that directly influences the corrosion resistance is the painting system used. Within this context, the GMB, in partnership with CSN, has been performing several works by adding the knowledge of the supplier to automotive technology. An example of this partnership we have the present study, which aimed to, comparatively, evaluate the corrosion resistance of two systems of painted galvanized steel, the first one with pre-treatment based on a traditional phosphate, and the another one based on a nano-ceramic film. In this study, was found out that materials with pre-treatment based on results of nanotechnology showed similar corrosion resistance comparing the phosphatized materials in a traditional way.

  9. Reliability Centered Maintenance in Schedule Improvement of Automotive Assembly Industry

    Directory of Open Access Journals (Sweden)

    Rizauddin Ramli

    2012-01-01

    Full Text Available Problem statement: Today, in many automotive manufacturing companies, maintenance management is an important factor to maintain the plant operation and production equipments. Approach: In this study, we present an implementation of Reliability Centered Maintenance (RCM practice in one of the automotive manufacturing company in Malaysia. The RCM practice was used to assist the company in focusing their maintenance activities based on the criticalities of the equipments by applying the Failure Modes and Effects Analysis (FMEA. The implementation of RCM was carried out in 4 stages; preparation, system analysis, decision making and feedback. The aim of RCM was to reduce the number of maintenance checklist and to improve significantly the integrity of maintenance practice. Results: As a result, the new RCM framework was generated where Class A equipment was at the top of the monthly maintenance frequency priority, followed by Class B and Class C equipment which had lesser critical value. Conclusion: The new RCM framework is used to conduct visible guideline and propose a new maintenance schedule. The guideline is useful for future maintenance strategy improvement. After the implementation, it can be ascertained that our proposed RCM is useful in reducing maintenance personnel burden and this leads to improvement of productivity.

  10. Prices, taxes and automotive fuel cross-border shopping

    Energy Technology Data Exchange (ETDEWEB)

    Leal, Andres [Department of Economics, Finance and Employment, Government of Aragon, Plaza de los Sitios, 7, 50.001-Zaragoza (Spain); Lopez-Laborda, Julio; Rodrigo, Fernando [Department of Public Economics, University of Zaragoza, Gran Via, 2, 50.005-Zaragoza (Spain)

    2009-03-15

    The aim of the present paper is to determine whether differences in automotive fuel prices among neighboring Autonomous Communities (i.e. Spanish political-administrative regions) affect the decisions taken by individuals regarding the region in which to purchase fuel. In particular, the intention is to discover if price increases in certain Autonomous Communities, as a result of the application of the regional tranche of the Hydrocarbon Retail Sales Tax (HRST) has affected fuel purchases in neighboring Communities. In order to achieve the above-mentioned objectives, the monthly purchases of automotive diesel in Aragon between January 2001 and March 2007 is estimated from the fuel price in Aragon, the relation between prices in each of the bordering Communities and Aragon, weighted by density of traffic, the number of vehicles registered in that Community, and three dummy variables representative of the implementation of the regional tranche of the HRST in Madrid, Catalonia, and Valencia. The paper finds empirical evidence to demonstrate a positive effect of the relative prices in the neighboring Communities and vehicle registrations, and also a negative effect of prices in Aragon, upon the acquisition of diesel in this region. In the case of Catalonia, some evidence suggests that the price effect may have been strengthened following the introduction of the regional tranche of the HRST in August 2004. (author)

  11. Implementation of 3D Optical Scanning Technology for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Abdil Kuş

    2009-03-01

    Full Text Available Reverse engineering (RE is a powerful tool for generating a CAD model from the 3D scan data of a physical part that lacks documentation or has changed from the original CAD design of the part. The process of digitizing a part and creating a CAD model from 3D scan data is less time consuming and provides greater accuracy than manually measuring the part and designing the part from scratch in CAD. 3D optical scanning technology is one of the measurement methods which have evolved over the last few years and it is used in a wide range of areas from industrial applications to art and cultural heritage. It is also used extensively in the automotive industry for applications such as part inspections, scanning of tools without CAD definition, scanning the casting for definition of the stock (i.e. the amount of material to be removed from the surface of the castings model for CAM programs and reverse engineering. In this study two scanning experiments of automotive applications are illustrated. The first one examines the processes from scanning to re-manufacturing the damaged sheet metal cutting die, using a 3D scanning technique and the second study compares the scanned point clouds data to 3D CAD data for inspection purposes. Furthermore, the deviations of the part holes are determined by using different lenses and scanning parameters.

  12. Property Criteria for Automotive Al-Mg-Si Sheet Alloys

    Directory of Open Access Journals (Sweden)

    Ramona Prillhofer

    2014-07-01

    Full Text Available In this study, property criteria for automotive Al-Mg-Si sheet alloys are outlined and investigated in the context of commercial alloys AA6016, AA6005A, AA6063 and AA6013. The parameters crucial to predicting forming behavior were determined by tensile tests, bending tests, cross-die tests, hole-expansion tests and forming limit curve analysis in the pre-aged temper after various storage periods following sheet production. Roping tests were performed to evaluate surface quality, for the deployment of these alloys as an outer panel material. Strength in service was also tested after a simulated paint bake cycle of 20 min at 185 °C, and the corrosion behavior was analyzed. The study showed that forming behavior is strongly dependent on the type of alloy and that it is influenced by the storage period after sheet production. Alloy AA6016 achieves the highest surface quality, and pre-ageing of alloy AA6013 facilitates superior strength in service. Corrosion behavior is good in AA6005A, AA6063 and AA6016, and only AA6013 shows a strong susceptibility to intergranular corrosion. The results are discussed below with respect to the chemical composition, microstructure and texture of the Al-Mg-Si alloys studied, and decision-making criteria for appropriate automotive sheet alloys for specific applications are presented.

  13. Sheet Forming Simulation For AHSS Components In The Automotive Industry

    Science.gov (United States)

    Asgari, Alireza; Pereira, Michael; Clark, Ben; Dingle, Matthew; Hodgson, Peter

    2004-06-01

    The trend in the automotive industry towards new advanced high strength steels (AHSS), combined with the ongoing reduction in program lead times have increased the need to get tool designs right, first time. Despite the fact that the technology used by sheet metal stamping companies to design and manufacture tooling is advancing steadily, finding optimal process parameters and tool geometries remains a challenge. Consequently, there has been a transition from designs based largely on trial and error techniques and the experience of the stamping engineer, to the increased use of virtual manufacturing and finite element (FE) simulation predictions as an indispensable tool in the design process. This work investigates the accuracy of FE techniques in predicting the forming behavior of AHSS grades, such as TRIP and dual phase, as compared to more commonly used conventional steel grades. Three different methods of simulation, one-step, implicit and explicit techniques, were used to model the forming process for an automotive part. Results were correlated with experimental strain and thickness measurements of manufactured components from the production line.

  14. The impact of global warming on the automotive industry

    Science.gov (United States)

    Hannappel, Ralf

    2017-08-01

    One cause of global warming of the earth's atmosphere is the emission of human made gases (methane, CO2, nitrous oxygen, etc.) into the environment. Of the total global CO2 emissions the transportation sector contributes to about 14%. In order to control the emissions of the automotive sector, in all major countries (USA, Europe, China, Japan) of the world, tough emissions targets were being set to reduce the vehicle traffic's contribution of CO2. These are derived from the global climate conference' target to limit the maximum temperature increase of the earth of 2 degrees Celsius until 2100. In order to achieve these stringent targets the automotive industry will face a major change in its drivetrain. It will move from combustion to electrical engines. The technical realization of these engines will most likely be battery and fuel cell driven propulsion systems. In order to achieve that transition a major effort is required in 4 industrial areas, i.e. growing electrical charging infrastructure, lowering battery cost, increasing the battery-electric vehicle ranges and developing new environmental friendly hydrogen production methods.

  15. Direct Injection Compression Ignition Diesel Automotive Technology Education GATE Program

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, Carl L

    2006-09-25

    The underlying goal of this prqject was to provide multi-disciplinary engineering training for graduate students in the area of internal combustion engines, specifically in direct injection compression ignition engines. The program was designed to educate highly qualified engineers and scientists that will seek to overcome teclmological barriers preventing the development and production of cost-effective high-efficiency vehicles for the U.S. market. Fu1iher, these highly qualified engineers and scientists will foster an educational process to train a future workforce of automotive engineering professionals who are knowledgeable about and have experience in developing and commercializing critical advanced automotive teclmologies. Eight objectives were defmed to accomplish this goal: 1. Develop an interdisciplinary internal co1nbustion engine curriculum emphasizing direct injected combustion ignited diesel engines. 2. Encourage and promote interdisciplinary interaction of the faculty. 3. Offer a Ph.D. degree in internal combustion engines based upon an interdisciplinary cuniculum. 4. Promote strong interaction with indusuy, develop a sense of responsibility with industry and pursue a self sustaining program. 5. Establish collaborative arrangements and network universities active in internal combustion engine study. 6. Further Enhance a First Class educational facility. 7. Establish 'off-campus' M.S. and Ph.D. engine programs of study at various indusuial sites. 8. Extend and Enhance the Graduate Experience.

  16. Precious metal-support interaction in automotive exhaust catalysts

    Institute of Scientific and Technical Information of China (English)

    郑婷婷; 何俊俊; 赵云昆; 夏文正; 何洁丽

    2014-01-01

    Precious metal-support interaction plays an important role in thermal stability and catalytic performance of the automotive exhaust catalysts. The support is not only a carrier for active compounds in catalysts but also can improve the dispersion of precious metals and suppress the sintering of precious metals at high temperature;meanwhile, noble metals can also enhance the redox per-formance and oxygen storage capacity of support. The mechanism of metal-support interactions mainly includes electronic interaction, formation of alloy and inward diffusion of metal into the support or covered by support. The form and degree of precious metal-sup-port interaction depend on many factors, including the content of precious metal, the species of support and metal, and preparation methods. The research results about strong metal-support interaction (SMSI) gave a theory support for developing a kind of new cata-lyst with excellent performance. This paper reviewed the interaction phenomenon and mechanism of precious metals (Pt, Pd, Rh) and support such as Al2O3, CeO2, and CeO2-based oxides in automotive exhaust catalysts. The factors that affect SMSI and the catalysts developed by SMSI were also discussed.

  17. Global sustainability and key needs in future automotive design.

    Science.gov (United States)

    McAuley, John W

    2003-12-01

    The number of light vehicle registrations is forecast to increase worldwide by a factor of 3-5 over the next 50 years. This will dramatically increase environmental impacts worldwide of automobiles and light trucks. If light vehicles are to be environmentally sustainable globally, the automotive industry must implement fundamental changes in future automotive design. Important factors in assessing automobile design needs include fuel economy and reduced emissions. Many design parameters can impact vehicle air emissions and energy consumption including alternative fuel or engine technologies, rolling resistance, aerodynamics, drive train design, friction, and vehicle weight. Of these, vehicle weight is key and will translate into reduced energy demand across all energy distribution elements. A new class of vehicles is needed that combines ultra-light design with a likely hybrid or fuel cell engine technology. This could increase efficiency by a factor of 3-5 and reduce air emissions as well. Advanced lightweight materials, such as plastics or composites, will need to overtake the present metal-based infrastructure. Incorporating design features to facilitate end-of-life recycling and recovery is also important. The trend will be towards fewer materials and parts in vehicle design, combined with ease of disassembly. Mono-material construction can create vehicle design with improved recyclability as well as reduced numbers of parts and weight.

  18. Concepts for particle foam based ultralight automotive interior parts

    Science.gov (United States)

    Trassl, C.; Altstädt, V.; Schreier, P.

    2014-05-01

    The described concepts for modern automotive interior parts are based on polypropylene (PP). These interior parts have a core of expanded polypropylene particle foam (EPP) and a decorative layer of a thermoplastic polyolefin elastomer (TPO) film. Compared with conventional solutions in the field of automotive interior parts, they are characterised mainly due to the avoidance of material mixtures so that they have better recycling properties and are significantly lighter in spite of comparable crash behaviour. Because of the optimized combination of positive component properties (specifically, the rigidity of the carrier, lower density combined with the better crash behaviour of the EPP foam core and good haptic and optical properties of the film), the multi-material system compensates the disadvantages of the individual components. In addition, the integration of all process steps into a new single-step manufacturing process combined with the elimination of an additional surface treatment means that the new ultra-light concept should lead to a significant reduction in the costs and cycle time.

  19. Passive Two-Phase Cooling of Automotive Power Electronics: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Moreno, G.; Jeffers, J. R.; Narumanchi, S.; Bennion, K.

    2014-08-01

    Experiments were conducted to evaluate the use of a passive two-phase cooling strategy as a means of cooling automotive power electronics. The proposed cooling approach utilizes an indirect cooling configuration to alleviate some reliability concerns and to allow the use of conventional power modules. An inverter-scale proof-of-concept cooling system was fabricated, and tests were conducted using the refrigerants hydrofluoroolefin HFO-1234yf and hydrofluorocarbon HFC-245fa. Results demonstrated that the system can dissipate at least 3.5 kW of heat with 250 cm3 of HFC-245fa. An advanced evaporator design that incorporates features to improve performance and reduce size was conceived. Simulation results indicate its thermal resistance can be 37% to 48% lower than automotive dual side cooled power modules. Tests were also conducted to measure the thermal performance of two air-cooled condensers--plain and rifled finned tube designs. The results combined with some analysis were then used to estimate the required condenser size per operating conditions and maximum allowable system (i.e., vapor and liquid) temperatures.

  20. Design method for automotive high-beam LED optics

    Science.gov (United States)

    Byzov, Egor V.; Moiseev, Mikhail A.; Doskolovich, Leonid L.; Kazanskiy, Nikolay L.

    2015-09-01

    New analytical method for the calculation of the LED secondary optics for automotive high-beam lamps is presented. Automotive headlamps should illuminate the road and the curb at the distance of 100-150 meters and create a bright, flat, relatively powerful light beam. To generate intensity distribution of this kind we propose to use TIR optical element (collimator working on the total internal reflection principle) with array of microlenses (optical corrector) on the upper surface. TIR part of the optical element enables reflection of the side rays to the front direction and provides a collimated beam which incidents on the microrelief. Microrelief, in its turn, dissipates the light flux in horizontal direction to meet the requirements of the Regulations 112, 113 and to provide well-illuminated area across the road in the far field. As an example, we computed and simulated the optical element with the diameter of 33 millimeters and the height of 22 millimeters. Simulation data shows that three illuminating modules including Cree XP-G2 LED and lens allow generating an appropriate intensity distribution for the class D of UNECE Regulations.

  1. GATE Center of Excellence at UAB in Lightweight Materials for Automotive Applications

    Energy Technology Data Exchange (ETDEWEB)

    None

    2011-07-31

    This report summarizes the accomplishments of the UAB GATE Center of Excellence in Lightweight Materials for Automotive Applications. The first Phase of the UAB DOE GATE center spanned the period 2005-2011. The UAB GATE goals coordinated with the overall goals of DOE's FreedomCAR and Vehicles Technologies initiative and DOE GATE program. The FCVT goals are: (1) Development and validation of advanced materials and manufacturing technologies to significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost; (2) To provide a new generation of engineers and scientists with knowledge and skills in advanced automotive technologies. The UAB GATE focused on both the FCVT and GATE goals in the following manner: (1) Train and produce graduates in lightweight automotive materials technologies; (2) Structure the engineering curricula to produce specialists in the automotive area; (3) Leverage automotive related industry in the State of Alabama; (4) Expose minority students to advanced technologies early in their career; (5) Develop innovative virtual classroom capabilities tied to real manufacturing operations; and (6) Integrate synergistic, multi-departmental activities to produce new product and manufacturing technologies for more damage tolerant, cost-effective, and lighter automotive structures.

  2. Supplier–customer relationships: Weaknesses in south african automotive supply chains

    Directory of Open Access Journals (Sweden)

    M. J. Naude

    2012-11-01

    Full Text Available The South African automotive industry, which is an important sector in the South African economy, needs to function efficiently if it is to compete internationally. However, South African automotive components manufacturers (ACMs are not internationally competitive and automotive assemblers, also known as original equipment manufacturers (OEMs, often import cheaper components from abroad. All parties in the South African automotive supply chains need each other to ensure optimal efficiency and competitiveness. Furthermore, it is vital that good relationships exist between customers and suppliers in the automotive supply chains in South Africa. ACMs are central to automotive supply chains. A survey was conducted among ACMs to determine the nature of relationships that exist between buyers and suppliers in South Africa’s automotive supply chains. The results showed that collaborative relationships do indeed exist between members of the supply chain but that communication, understanding of the parties’ situations and cooperation can improve this relationship and so create total alliance between OEMs and ACMs.

  3. Sustaining Competitiveness Through product Development Activities Within Malaysian Automotive Suppliers

    Directory of Open Access Journals (Sweden)

    Norizah Mohamad

    2012-01-01

    Full Text Available The local automotive suppliers are facing a number of important challenges such asglobalisation, new requirement in market specifications and the competition brought about by theAsean Free Trade Area (AFTA agreements. In an effort to enhance the competitiveness of themanufacturing sector, the government has implemented the Second Industrial Master Plan, IMP2(1996-2005. The focus of the IMP2 is more on innovation and applications of new technologies, sothat industries can move up the value chain of their activities. Innovative capabilities achieved fromcompanies’ new product development activities have been recognized to be crucial for companies tosustain their competitiveness and organisational success. The importance of product development ismost obvious in the context of the discussion on the competitiveness of the Malaysian automotivesuppliers. The study will focus on the small medium enterprises (SMEs that make up more than 60 %of these automotive suppliers. The study is to determine the extensiveness of the suppliers’ productdevelopment activities by examining the involvement of the suppliers in customer’s productdevelopment activities. Consequently, the impact of this involvement to the competitiveness of thesuppliers is examined. The results were established based from a survey to parts and componentssuppliers of Proton, the Malaysian car national assembler. The study has shown that the SMEs wereinvolved from the early stages of the product development process that is during the design stage. Theproduct development efforts have shown to contribute towards increasing firms’ market share andfirms were also able to gain a better understanding of future product demand. A significant number ofthe suppliers have managed to penetrate the export market. Unfortunately, among the respondents,there is only one system supplier. This indicates that, either the technological capabilities of theSMEs still needed upgrading for the requirement as

  4. Thermal Comfort Assessment: A Case Study at Malaysian Automotive Industry

    Directory of Open Access Journals (Sweden)

    A. R. Ismail

    2009-01-01

    Full Text Available Problem statement: Thermal comfort has a great influence on the productivity and satisfaction of indoor building occupants. The exposure to excessive heat during work may cause discomfort and contributed to low productivity among workers. Malaysia known with its hot and humid weather where in most of the survey study published indicated that workers in Malaysia automotive industries had exposed to excessive temperature while working. The study investigated the thermal comfort level experienced by workers at Malaysian automotive industry. Approach: The study had been conducted at one automotive parts assembly factory in Malaysia. The human subjects for the study constitute operators at tire receiving section of the factory. The environment examined was the relative humidity (%, WBGT, air temperature and radiant temperature (°C of the surrounding workstation area. The environmental factors were measured using Babuc apparatus, which is capable to measure simultaneously those mentioned environmental factors. The time series data of fluctuating level of factors were plotted to identify the significant changes of factors. Then thermal comfort of the workers was assessed by using ASHRAE thermal sensation scale by using Predicted Mean Vote (PMV. Further Predicted Percentage Dissatisfied (PPD was used to estimate the thermal comfort satisfaction of the occupant. Finally the PPD versus PMV were plotted to present the thermal comfort scenario of workers involved in related workstation. Results: The trend of relative humidity curve from the graph also indicated the increasing level of discomfort. The radiant temperature observed seems consistent during the study while there was decreasing of WBGT start from afternoon due to the rain. The study revealed that the PPD value of 54% of the workers population at the workstation are likely to be satisfied with thermal comfort at this station while the PMV index from ASHRAE indicated the value 1

  5. Sustaining Competitiveness Through product Development Activities Within Malaysian Automotive Suppliers

    Directory of Open Access Journals (Sweden)

    Norizah Mohamad

    2012-01-01

    Full Text Available The local automotive suppliers are facing a number of important challenges such asglobalisation, new requirement in market specifications and the competition brought about by theAsean Free Trade Area (AFTA agreements. In an effort to enhance the competitiveness of themanufacturing sector, the government has implemented the Second Industrial Master Plan, IMP2(1996-2005. The focus of the IMP2 is more on innovation and applications of new technologies, sothat industries can move up the value chain of their activities. Innovative capabilities achieved fromcompanies’ new product development activities have been recognized to be crucial for companies tosustain their competitiveness and organisational success. The importance of product development ismost obvious in the context of the discussion on the competitiveness of the Malaysian automotivesuppliers. The study will focus on the small medium enterprises (SMEs that make up more than 60 %of these automotive suppliers. The study is to determine the extensiveness of the suppliers’ productdevelopment activities by examining the involvement of the suppliers in customer’s productdevelopment activities. Consequently, the impact of this involvement to the competitiveness of thesuppliers is examined. The results were established based from a survey to parts and componentssuppliers of Proton, the Malaysian car national assembler. The study has shown that the SMEs wereinvolved from the early stages of the product development process that is during the design stage. Theproduct development efforts have shown to contribute towards increasing firms’ market share andfirms were also able to gain a better understanding of future product demand. A significant number ofthe suppliers have managed to penetrate the export market. Unfortunately, among the respondents,there is only one system supplier. This indicates that, either the technological capabilities of theSMEs still needed upgrading for the requirement as

  6. A proposed centralised distribution model for the South African automotive component industry

    Directory of Open Access Journals (Sweden)

    Micheline J. Naude

    2009-12-01

    Full Text Available Purpose: This article explores the possibility of developing a distribution model, similar to the model developed and implemented by the South African pharmaceutical industry, which could be implemented by automotive component manufacturers for supply to independent retailers. Problem Investigated: The South African automotive components distribution chain is extensive with a number of players of varying sizes, from the larger spares distribution groups to a number of independent retailers. Distributing to the smaller independent retailers is costly for the automotive component manufacturers. Methodology: This study is based on a preliminary study of an explorative nature. Interviews were conducted with a senior staff member from a leading automotive component manufacturer in KwaZulu Natal and nine participants at a senior management level at five of their main customers (aftermarket retailers. Findings: The findings from the empirical study suggest that the aftermarket component industry is mature with the role players well established. The distribution chain to the independent retailer is expensive in terms of transaction and distribution costs for the automotive component manufacturer. A proposed centralised distribution model for supply to independent retailers has been developed which should reduce distribution costs for the automotive component manufacturer in terms of (1 the lowest possible freight rate; (2 timely and controlled delivery; and (3 reduced congestion at the customer's receiving dock. Originality: This research is original in that it explores the possibility of implementing a centralised distribution model for independent retailers in the automotive component industry. Furthermore, there is a dearth of published research on the South African automotive component industry particularly addressing distribution issues. Conclusion: The distribution model as suggested is a practical one and should deliver added value to automotive

  7. A Versatile Mixed-Signal Pin Approach for Cost-Effective Test of Automotive ICs

    Institute of Scientific and Technical Information of China (English)

    Credence Systems Corporation

    2004-01-01

    @@ Integrated circuits (ICs) intended for increasingly sophisticated automotive applications bring unique test demands. Advanced ICs for applications such as highly integrated automatic braking system (ABS) and airbag controllers combine high voltage digital channels, significant VI demands and precise timing capability. Along with continued missioncritical reliability concerns, the trend toward higher voltage operation and increased device integration requires specialized test capabilities able to extend across the wide operating ranges found in automotive applications. Among these capabilities, automotive test requirements increasingly dictate a need for a cost-effective versatile mixed-signal pin electronics with very high data rates reaching up to 50MHz with a voltage swing of-2 V to +28 V.

  8. Super-capacitors as an energy storage for fuel cell automotive hybrid electrical system

    Energy Technology Data Exchange (ETDEWEB)

    Thounthong, P.; Rael, St.; Davat, B. [Institut National Polytechnique, GREEN-INPL-CNRS (UMR 7037), 54 - Vandoeuvre les Nancy (France)

    2004-07-01

    The design, implementation and testing of a purely super-capacitors energy storage system for automotive system having a fuel cell as main source are presented. The system employs a super-capacitive storage device, composed of six components (3500 F, 2.5 V, 400 A) associated in series. This device is connected to automotive 42 V DC bus by a 2-quadrant DC-DC converter. The control structure of the system is realised by means of analogical and digital control. The experimental results show that super-capacitors are suitable as energy storage device for fuel cell automotive electrical system. (authors)

  9. Grain Refiner Effect on the Microstructure and Mechanical Properties of the A356 Automotive Wheels

    Science.gov (United States)

    Aguirre-De la Torre, E.; Afeltra, U.; Gómez-Esparza, C. D.; Camarillo-Cisneros, J.; Pérez-Bustamante, R.; Martínez-Sánchez, R.

    2013-12-01

    A356 aluminum alloy automotive wheels, 17 inch in diameter, were produced by low-pressure die casting. Contents of Al-5Ti-B (ATB) master alloy were added from 0 to 0.79 wt.%. Microstructural and mechanical properties were evaluated under industrial casting process conditions. The obtained results from mechanical testing provide evidence that additions of 0.13 and 0.27 wt.% of ATB have an improvement on the mechanical performance of the automotive wheels. This can be compared with the use of a grain refiner's higher concentrations, leading to a significant reduction in the cost-benefit ratio for the manufacturing of A356 automotive wheels.

  10. SOI technology for power management in automotive and industrial applications

    Science.gov (United States)

    Stork, Johannes M. C.; Hosey, George P.

    2017-02-01

    Semiconductor on Insulator (SOI) technology offers an assortment of opportunities for chip manufacturers in the Power Management market. Recent advances in the automotive and industrial markets, along with emerging features, the increasing use of sensors, and the ever-expanding "Internet of Things" (IoT) are providing for continued growth in these markets while also driving more complex solutions. The potential benefits of SOI include the ability to place both high-voltage and low-voltage devices on a single chip, saving space and cost, simplifying designs and models, and improving performance, thereby cutting development costs and improving time to market. SOI also offers novel new approaches to long-standing technologies.

  11. DOES CSR ENHANCE MARKET PERFORMANCE FOR AUTOMOTIVE COMPANIES?

    Directory of Open Access Journals (Sweden)

    Anca BUTNARIU

    2016-12-01

    Full Text Available This paper aims at analyzing the role of strategic CSR in creating stable long term performance in the automotive industry. The first part of the paper reviews the success factors for the European auto industry and analyses the influence strategic CSR has on these factors. In order to illustrate the relation between strategic CSR activities and the economic performance, the paper presents the strategic evolution of one of the most ancient motor companies on the international scene, namely Peugeot and evaluates the innovative ideas brought into the market, as well as its future prospects. The PSA Group holds a position of European leader in terms of CO2 emissions, with an average of 110.3 grams of CO2/km in 2014. The PSA Peugeot Citroen Group’s strategy is being increasingly oriented towards environmental protection and energy saving.

  12. International Forum on Advanced Microsystems for Automotive Application

    CERN Document Server

    Meyer, Gereon

    2014-01-01

    The automobile is going through the biggest transformation in its history. Automation and electrification of vehicles are expected to enable safer and cleaner mobility. The prospects and requirements of the future automobile affect innovations in major technology fields like driver assistance systems, vehicle networking and drivetrain development. Smart systems such as adaptive ICT components and MEMS devices, novel network architectures, integrated sensor systems, intelligent interfaces and functional materials form the basis of these features and permit their successful and synergetic integration. It has been the mission of the International Forum on Advanced Microsystems for Automotive Applications (AMAA) for more than fifteen years to detect novel trends and to discuss the technological implications from early on. Therefore, the topic of the AMAA 2014 will be “Smart Systems for Safe, Clean, and Automated Vehicles”. This book contains peer-reviewed papers written by leading engineers and researchers w...

  13. Dynamics of Innovation Networks in the German Automotive Industry

    DEFF Research Database (Denmark)

    Buchmann, Tobias; Hain, Daniel; Kudic, Muhamed

    2017-01-01

    Innovation is, above all, a social process depending on mutual interactions of individuals aiming at accessing and exchanging external inputs in order to generate novel good and services. Accordingly, the interest in – and research on – interfirm innovation networks has sharply increased over...... the last decade. The structural dynamics of networks are driven by endogenous and exogenous forces. In this paper, we particularly stress the role of endogenous determinants of network evolution of interfirm networks – a category of often underestimated forces. We employ a longitudinal dataset...... that compromises German automotive firms between 2002 and 2006 and apply a stochastic actor-oriented model (SAOM) designed to analyze the importance of endogenous and exogenous determinants. Our results show that endogenous determinants – proxied by measures for local and global clustering – have a higher...

  14. Analysis of automotive liftgate seals using finite element analysis

    Directory of Open Access Journals (Sweden)

    Rafael H. T Ueda

    2010-01-01

    Full Text Available Seals have wide application in automotive products. They are responsible for sealing the car in several parts such as the doors, the air intake cowl seal, and air intake lights seal. Strain and stress studies are very important in order to understand the behavior of polymeric materials, which are generally submitted to great workload variation and environmental influence. This study of EPDM rubber was carried out to define the strain, stress and yield stress. Tensile and compression tests were carried out on workpieces with 100 mm of length. The data were acquired using the Qmat software. A Finite Element Analysis using the MSC Marc MentatTM was conducted and compared with experimental tests. The results showed an increase of effort proportional to bulb thickness. The proportional increase of compression effort for different displacements was significant. Moreover, physical parameters such as length, thickness, and friction coefficient changed the strain and stress rate.

  15. An Organizational Knowledge Ontology for Automotive Supply Chains

    Science.gov (United States)

    Hellingrath, Bernd; Witthaut, Markus; Böhle, Carsten; Brügger, Stephan

    The currently completed ILIPT (Intelligent Logistics for Innovative Product Technologies) project was concerned with the concept of the “5 day car” (a customized car that is delivered within five days after its ordering) and encompassed extensive research on the required production and logistics network structures and processes. As car manufacturers in the automotive industry (commonly referred to as OEMs) rely heavily on their suppliers, the major challenge lies in the organization of inter-enterprise cooperation supported by information systems (IS) in an efficient manner. A common understanding of supply chain concepts is indispensable for this. Ontologies as formal representations of concepts can be used as a semantic basis for cooperation. Relevant results from ILIPT are presented followed by a concept as well as a prototype of how to transfer the theoretical findings to a practical implementation, in this case a multi-agent system.

  16. Automotive Painting Technology A Monozukuri-Hitozukuri Perspective

    CERN Document Server

    Salazar, Abraham; Saito, Kozo

    2013-01-01

    This book offers unique and valuable contributions to the field. It offers breadth and inclusiveness. Most existing works on automotive painting cover only a single aspect of this complex topic, such as the chemistry of paint or paint booth technology. Monozukuri and Hitozukuri are Japanese terms that can be translated as “making things” and “developing people” but their implications in Japanese are richer and more complex than this minimal translation would indicate. The Monozukuri-Hitozukuri perspective is drawn from essential principles on which the Toyota approach to problem-solving and continuous improvement is based. From this perspective, neither painting technology R&D nor painting technology use in manufacturing can be done successfully without integrating technological and human concerns involved with making and learning in the broadest sense, as the hyphen is meant to indicate. The editors provide case studies and examples -- drawn from Mr. Toda’s 33 years of experience with automotiv...

  17. Simulation of the noise transmission through automotive door seals

    CERN Document Server

    Hazir, Andreas

    2016-01-01

    Andreas Hazir is investigating the door seal contribution to the interior noise level of production vehicles. These investigations contain experimental contribution analyses of real production vehicles and of academic test cases as well as the development of a simulation methodology for noise transmission through sealing systems and side windows. The simulations are realized by coupling transient computational aeroacoustics of the exterior flow to nonlinear finite element simulations of the structural transmission. By introducing a linear transmission model, the setup and computational costs of the seal noise transmission are significantly reduced, resulting in the feasibility of numerical contribution analyses of real production vehicles. Contents Contribution Analyses of Production Vehicles Acoustic Excitation versus Aeroacoustic Excitation Development of a Simulation Methodology Sensitivity Analysis of Noise Transmission Simulations Target Groups Researchers and students in the field of automotive engineer...

  18. A Multiobjective Optimization Model in Automotive Supply Chain Networks

    Directory of Open Access Journals (Sweden)

    Abdolhossein Sadrnia

    2013-01-01

    Full Text Available In the new decade, green investment decisions are attracting more interest in design supply chains due to the hidden economic benefits and environmental legislative barriers. In this paper, a supply chain network design problem with both economic and environmental concerns is presented. Therefore, a multiobjective optimization model that captures the trade-off between the total logistics cost and CO2 emissions is proposed. With regard to the complexity of logistic networks, a new multiobjective swarm intelligence algorithm known as a multiobjective Gravitational search algorithm (MOGSA has been implemented for solving the proposed mathematical model. To evaluate the effectiveness of the model, a comprehensive set of numerical experiments is explained. The results obtained show that the proposed model can be applied as an effective tool in strategic planning for optimizing cost and CO2 emissions in an environmentally friendly automotive supply chain.

  19. Face to Face : The Perception of Automotive Designs.

    Science.gov (United States)

    Windhager, Sonja; Slice, Dennis E; Schaefer, Katrin; Oberzaucher, Elisabeth; Thorstensen, Truls; Grammer, Karl

    2008-12-01

    Over evolutionary time, humans have developed a selective sensitivity to features in the human face that convey information on sex, age, emotions, and intentions. This ability might not only be applied to our conspecifics nowadays, but also to other living objects (i.e., animals) and even to artificial structures, such as cars. To investigate this possibility, we asked people to report the characteristics, emotions, personality traits, and attitudes they attribute to car fronts, and we used geometric morphometrics (GM) and multivariate statistical methods to determine and visualize the corresponding shape information. Automotive features and proportions are found to covary with trait perception in a manner similar to that found with human faces. Emerging analogies are discussed. This study should have implications for both our understanding of our prehistoric psyche and its interrelation with the modern world.

  20. Experimental Study of Castor Oil Based Lubricant for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Amit Suhane,

    2014-01-01

    Full Text Available Vegetable oils due to their better natural propertiescan be used as an alternative to reduce the dependency on the conventional lubricants. With the depletion of conventional resources at faster pace, need of hour is to approach the safer alternatives for ensuring the availability of such resources for longer periods with lesser harm to the mankind and sorroundings.This workevaluates the prospects of Castor oil based lubricant for automotive applications in contrast to the available commercial servo gear oil. Experimentation has been performed on four ball tester set up.Material used is carbon steel balls. Refined castor and mahua oils are blended in fixed ratios and subjected to friction and wear tests. Experimentation reveals that castor mahua oil blend possess immense potential in contrast to servo gear oil due to good wear reducing traits apart from environmental benefits.

  1. Ceramics for the AGT101 automotive gas turbine

    Science.gov (United States)

    Kreiner, D. M.; Wimmer, J. M.

    1981-01-01

    An advanced gas turbine powertrain for automotive application is being developed. Objectives of the program include a fuel consumption of 42.8 mpg on No. 2 diesel fuel in a 3000 pound car, same overall vehicle performance as obtained with a conventional spark ignition internal combustion engine, low emission, multiple fuel capacity, reliability, and competitive cost. The AGT101 powertrain consists of a power section, gearbox and transmission, and the design and analysis conducted thus far support the initial engine concept, as no significant design changes have been required. The ceramic rotor design approach and component materials are discussed, and it is projected that the AGT powertrain will be competitive with any other alternative powertrain in meeting the design objectives.

  2. SUPPLY CHAIN RESILIENCE ANALYSIS: A BRAZILIAN AUTOMOTIVE CASE

    Directory of Open Access Journals (Sweden)

    Luiz Felipe Scavarda

    2015-04-01

    Full Text Available Supply chain (SC resilience and flexibility are important research topics receiving growing attention. However, the academic literature needs empirical studies on SC resilience capable of investigating the inter-organizational components of flexibility along different tiers. Therefore, this paper analyzes the main lack of flexibilities in three Brazilian automotive SCs that limit their resilience and therefore their capacity to better support and meet the demand changes in the marketplace. A multi-tier case study approach is adopted. Research findings identify lack of flexibilities in different tiers that inhibit the SC resilience as well as manufacturing and SC flexibilities that build SC resilience. The findings also highlight that the same SC may have the flexibility to be resilient for one of its products but not for another product, what sheds new lights on the academic literature. Finally, flexible SCs should be designed to increase SC resilience to cope with mishaps as significant demand changes.

  3. Assessment of Automotive Coatings Used on Different Metallic Substrates

    Directory of Open Access Journals (Sweden)

    W. Bensalah

    2014-01-01

    Full Text Available Four epoxy primers commonly used in the automotive industry were applied by gravity pneumatic spray gun over metallic substrates, specifically, steel, electrogalvanized steel, hot-dip galvanized steel, and aluminum. A two-component polyurethane resin was used as topcoat. To evaluate the performance of the different coating systems, the treated panels were submitted to mechanical testing using Persoz hardness, impact resistance, cupping, lattice method, and bending. Tribological properties of different coating systems were conducted using pin on disc machine. Immersion tests were carried out in 5% NaCl and immersion tests in 3% NaOH solutions. Results showed which of the coating systems is more suitable for each substrate in terms of mechanical, tribological, and anticorrosive performance.

  4. Monitoring automotive oil degradation: analytical tools and onboard sensing technologies.

    Science.gov (United States)

    Mujahid, Adnan; Dickert, Franz L

    2012-09-01

    Engine oil experiences a number of thermal and oxidative phases that yield acidic products in the matrix consequently leading to degradation of the base oil. Generally, oil oxidation is a complex process and difficult to elucidate; however, the degradation pathways can be defined for almost every type of oil because they mainly depend on the mechanical status and operating conditions. The exact time of oil change is nonetheless difficult to predict, but it is of great interest from an economic and ecological point of view. In order to make a quick and accurate decision about oil changes, onboard assessment of oil quality is highly desirable. For this purpose, a variety of physical and chemical sensors have been proposed along with spectroscopic strategies. We present a critical review of all these approaches and of recent developments to analyze the exact lifetime of automotive engine oil. Apart from their potential for degradation monitoring, their limitations and future perspectives have also been investigated.

  5. Hybrid Automotive Engine Using Ethanol-Burning Miller Cycle

    Science.gov (United States)

    Weinstein, Leonard

    2004-01-01

    A proposed hybrid (internal-combustion/ electric) automotive engine system would include as its internal-combustion subsystem, a modified Miller-cycle engine with regenerative air preheating and with autoignition like that of a Diesel engine. The fuel would be ethanol and would be burned lean to ensure complete combustion. Although the proposed engine would have a relatively low power-to-weight ratio compared to most present engines, this would not be the problem encountered if this engine were used in a non-hybrid system since hybrid systems require significantly lower power and thus smaller engines than purely internal-combustion-engine-driven vehicles. The disadvantage would be offset by the advantages of high fuel efficiency, low emission of nitrogen oxides and particulate pollutants, and the fact that ethanol is a renewable fuel. The original Miller-cycle engine, named after its inventor, was patented in the 1940s and is the basis of engines used in some modern automobiles, but is not widely known. In somewhat oversimplified terms, the main difference between a Miller-cycle engine and a common (Otto-cycle) automobile engine is that the Miller-cycle engine has a longer expansion stroke while retaining the shorter compression stroke. This is accomplished by leaving the intake valve open for part of the compression stroke, whereas in the Otto cycle engine, the intake valve is kept closed during the entire compression stroke. This greater expansion ratio makes it possible to extract more energy from the combustion process without expending more energy for compression. The net result is greater efficiency. In the proposed engine, the regenerative preheating would be effected by running the intake air through a heat exchanger connected to the engine block. The regenerative preheating would offer two advantages: It would ensure reliable autoignition during operation at low ambient temperature and would help to cool the engine, thereby reducing the remainder of the

  6. Standard Compliant Hazard and Threat Analysis for the Automotive Domain

    Directory of Open Access Journals (Sweden)

    Kristian Beckers

    2016-06-01

    Full Text Available The automotive industry has successfully collaborated to release the ISO 26262 standard for developing safe software for cars. The standard describes in detail how to conduct hazard analysis and risk assessments to determine the necessary safety measures for each feature. However, the standard does not concern threat analysis for malicious attackers or how to select appropriate security countermeasures. We propose the application of ISO 27001 for this purpose and show how it can be applied together with ISO 26262. We show how ISO 26262 documentation can be re-used and enhanced to satisfy the analysis and documentation demands of the ISO 27001 standard. We illustrate our approach based on an electronic steering column lock system.

  7. Two-Mode Operation Engine Mount Design for Automotive Applications

    Directory of Open Access Journals (Sweden)

    Reza Tikani

    2012-01-01

    Full Text Available Hydraulic engine mounts are applied to the automotive applications to isolate the chassis from the high frequency noise and vibration generated by the engine as well as to limit the engine shake motions resulting at low frequencies. In this paper, a new hydraulic engine mount with a controllable inertia track profile is proposed and its dynamic behavior is investigated. The profile of the inertia track is varied by applying a controlled force to a cylindrical rubber disk, placed in the inertia track. This design provides a hydraulic engine mount design with an adjustable notch frequency location and also damping characteristics in shake motions. By using a simple control strategy, the efficiency of the proposed hydraulic engine mount in two-mode operation meaning isolating mode in the highway driving condition and damping mode in the shock motions, is investigated.

  8. Wide-Bandgap Semiconductor Devices for Automotive Applications

    Science.gov (United States)

    Sugimoto, M.; Ueda, H.; Uesugi, T.; Kachi, T.

    2007-06-01

    In this paper, we discuss requirements of power devices for automotive applications, especially hybrid vehicles and the development of GaN power devices at Toyota. We fabricated AlGaN/GaN HEMTs and measured their characteristics. The maximum breakdown voltage was over 600V. The drain current with a gate width of 31mm was over 8A. A thermograph image of the HEMT under high current operation shows the AlGaN/GaN HEMT operated at more than 300°C. And we confirmed the operation of a vertical GaN device. All the results of the GaN HEMTs are really promising to realize high performance and small size inverters for future automobiles.

  9. 5th International Conference on Sustainable Automotive Technologies

    CERN Document Server

    Subic, Aleksandar; Trufin, Ramona

    2014-01-01

    This book captures selected peer reviewed papers presented at the 5th International Conference on Sustainable Automotive Technologies, ICSAT 2013, held in Ingolstadt, Germany. ICSAT is the state-of-the-art conference in the field of new technologies for transportation. The book brings together the work of international researchers and practitioners under the following interrelated headings: fuel transportation and storage, material recycling, manufacturing and management costs, engines and emission reduction. The book provides a very good overview of research and development activities focused on new technologies and approaches capable of meeting the challenges to sustainable mobility. About the Editors: Prof. Dr. Jörg Wellnitz is the Dean of the Faculty of Mechanical Engineering, Technische Hochschule Ingolstadt, Germany. Prof. Dr. Aleksandar Subic is the Head of the School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Australia. Ramona Trufin, M.A. is the coordinator of the Facul...

  10. Automotive Stirling Engine Development Program Mod I Stirling engine development

    Science.gov (United States)

    Simetkosky, M. A.

    1983-01-01

    The development of the Mod I 4-cylinder automotive Stirling engine is discussed and illustrated with drawings, block diagrams, photographs, and graphs and tables of preliminary test data. The engine and its drive, cold-engine, hot-engine, external-heat, air/fuel, power-control, electronic-control, and auxiliary systems are characterized. Performance results from a total of 1900 h of tests on 4 prototype engines include average maximum efficiency (at 2000 rpm) 34.5 percent and maximum output power 54.4 kW. The modifications introduced in an upgraded version of the Mod I are explained; this engine has maximum efficiency 40.4 percent and maximum power output 69.2 kW.

  11. Effects of cavitation on performance of automotive torque converter

    Directory of Open Access Journals (Sweden)

    Jaewon Ju

    2016-06-01

    Full Text Available Cavitation is a phenomenon whereby vapor bubbles of a flowing liquid are formed in a local region where the pressure of the liquid is below its vapor pressure. It is well known that cavitation in torque converters occurs frequently when a car with an automatic transmission makes an abrupt start. Cavitation is closely related to a performance drop and noise generation at a specific operating condition in a car and a torque converter itself. This study addressed the relation between cavitation and performance in an automotive torque converter in a quantitative and qualitative manner using numerical simulations. The cavitation was calculated at various operating conditions using a commercial flow solver with the homogeneous cavitation model, and the torque converter performance was compared with the experimental data. Numerical results well match to the data and indicate that the cavitation causes significant performance drop, as the pump speed increases or both speed ratio and reference pressure decrease.

  12. Multisensor Data Fusion for Automotive Engine Fault Diagnosis

    Institute of Scientific and Technical Information of China (English)

    王赟松; 褚福磊; 何永勇; 郭丹

    2004-01-01

    This paper describes mainly a decision-level data fusion technique for fault diagnosis for electronically controlled engines.Experiments on a SANTANA AJR engine show that the data fusion method provides good engine fault diagnosis.In data fusion methods, the data level fusion has small data preprocessing loads and high accuracy, but requires commensurate sensor data and has poor operational performance.The decision-level fusion based on Dempster-Shafer evidence theory can process noncommensurate data and has robust operational performance, reduces ambiguity, increases confidence, and improves system reliability, but has low fusion accuracy and high data preprocessing cost.The feature-level fusion provides good compromise between the above two methods, which becomes gradually mature.In addition, acquiring raw data is a precondition to perform data fusion, so the system for signal acquisition and processing for an automotive engine test is also designed by the virtual instrument technology.

  13. Design of electromagnetic shock absorbers for automotive suspensions

    Science.gov (United States)

    Amati, Nicola; Festini, Andrea; Tonoli, Andrea

    2011-12-01

    Electromechanical dampers seem to be a valid alternative to conventional shock absorbers for automotive suspensions. They are based on linear or rotative electric motors. If they are of the DC-brushless type, the shock absorber can be devised by shunting its electric terminals with a resistive load. The damping force can be modified by acting on the added resistance. To supply the required damping force without exceeding in size and weight, a mechanical or hydraulic system that amplifies the speed is required. This paper illustrates the modelling and design of such electromechanical shock absorbers. This paper is devoted to describe an integrated design procedure of the electrical and mechanical parameters with the objective of optimising the device performance. The application to a C class front suspension car has shown promising results in terms of size, weight and performance.

  14. Enhanced test methods to characterise automotive battery cells

    Science.gov (United States)

    Mulder, Grietus; Omar, Noshin; Pauwels, Stijn; Leemans, Filip; Verbrugge, Bavo; De Nijs, Wouter; Van den Bossche, Peter; Six, Daan; Van Mierlo, Joeri

    This article evaluates the methods to characterise the behaviour of lithium ion cells of several chemistries and a nickel metal hydride cell for automotive applications like (plug-in) hybrid vehicles and battery electric vehicles. Although existing characterisation test methods are used, it was also indicated to combine test methods in order to speed up the test time and to create an improved comparability of the test results. Also, the existing capacity tests ignore that cells can be charged at several current rates. However, this is of interest for, e.g. fast charging and regenerative braking. Tests for high power and high energy application have been integrated in the enhanced method. The article explains the rationale to ameliorate the test methods. The test plan should make it possible to make an initial division in a group of cells purchased from several suppliers.

  15. Frequency Weighting Filter Design for Automotive Ride Comfort Evaluation

    Institute of Scientific and Technical Information of China (English)

    DU Feng

    2016-01-01

    Few study gives guidance to design weighting filters according to the frequency weighting factors, and the additional evaluation method of automotive ride comfort is not made good use of in some countries. Based on the regularities of the weighting factors, a method is proposed and the vertical and horizontal weighting filters are developed. The whole frequency range is divided several times into two parts with respective regularity. For each division, a parallel filter constituted by a low-and a high-pass filter with the same cutoff frequency and the quality factor is utilized to achieve section factors. The cascading of these parallel filters obtains entire factors. These filters own a high order. But, low order filters are preferred in some applications. The bilinear transformation method and the least P-norm optimal infinite impulse response(IIR) filter design method are employed to develop low order filters to approximate the weightings in the standard. In addition, with the window method, the linear phase finite impulse response(FIR) filter is designed to keep the signal from distorting and to obtain the staircase weighting. For the same case, the traditional method produces 0.330 7 m•s–2 weighted root mean square(r.m.s.) acceleration and the filtering method gives 0.311 9 m•s–2 r.m.s. The fourth order filter for approximation of vertical weighting obtains 0.313 9 m•s–2 r.m.s. Crest factors of the acceleration signal weighted by the weighting filter and the fourth order filter are 3.002 7 and 3.011 1, respectively. This paper proposes several methods to design frequency weighting filters for automotive ride comfort evaluation, and these developed weighting filters are effective.

  16. Technical Efficiency of Automotive Industry Cluster in Chennai

    Science.gov (United States)

    Bhaskaran, E.

    2012-07-01

    Chennai is also called as Detroit of India due to its automotive industry presence producing over 40 % of the India's vehicle and components. During 2001-2002, diagnostic study was conducted on the Automotive Component Industries (ACI) in Ambattur Industrial Estate, Chennai and in SWOT analysis it was found that it had faced problems on infrastructure, technology, procurement, production and marketing. In the year 2004-2005 under the cluster development approach (CDA), they formed Chennai auto cluster, under public private partnership concept, received grant from Government of India, Government of Tamil Nadu, Ambattur Municipality, bank loans and stake holders. This results development in infrastructure, technology, procurement, production and marketing interrelationships among ACI. The objective is to determine the correlation coefficient, regression equation, technical efficiency, peer weights, slack variables and return to scale of cluster before and after the CDA. The methodology adopted is collection of primary data from ACI and analyzing using data envelopment analysis (DEA) of input oriented Banker-Charnes-Cooper model. There is significant increase in correlation coefficient and the regression analysis reveals that for one percent increase in employment and net worth, the gross output increases significantly after the CDA. The DEA solver gives the technical efficiency of ACI by taking shift, employment, net worth as input data and quality, gross output and export ratio as output data. From the technical score and ranking of ACI, it is found that there is significant increase in technical efficiency of ACI when compared to CDA. The slack variables obtained clearly reveals the excess employment and net worth and no shortage of gross output. To conclude there is increase in technical efficiency of not only Chennai auto cluster in general but also Chennai auto components industries in particular.

  17. Status of corrosions protection primers for the automotive industry

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann-Loeser, P. [Adam Opel AG, Ruesselsheim (Germany); Schnell, A. [DaimlerChrysler, Werk Sindelfingen (Germany); Stellnberger, K.H.; Androsch, F.M. [voestalpine Stahl, Linz (Austria); Reier, T. [SZMF, Salzgitter (Germany); Lewandowski, J. [ThyssenKrupp Stahl, Duisburg (Germany); Filthaut, C. [DOC Dortmunder OberflaechenCentrum, Dortmund (Germany); Besseyrias, A. [Arcelor / R and D LEDEPP, Florange (France); Dane, C. [Corus, Ijmuiden (Netherlands); Steinbeck, G. [Steel Institute VDEh, Duesseldorf (Germany)

    2005-07-01

    In Europe, 2.5 - 4 {mu}m Zn-pigmented corrosion protection primers (CPP) are being used by the automotive industry. A short introduction describing the development steps leading up to the state of the art will be given and also the reasons for using it in practice. For some applications it became necessary to try to achieve a significantly higher level of corrosion resistance than this ''first generation'' type coating can offer. It was also important to lower the curing temperature of the paint considerably in order to be able to supply bake-hardening grade steels. This type of corrosion protection primer is now called the ''second generation''. The Opel-production of the Astra-family started using 2{sup nd} generation CPP (4-6 {mu}m) on chromate-free pre-treatment and EG for hood and crash box in 2004. The newest developments show a high potential to lower the coating thickness even further and thus make cost savings possible. The development process is still ongoing and for effective progress, a good mutual basis for laboratory evaluation of properties is of valuable support. In a Steel Institute VDEh working group (Arcelor, Corus, Salzgitter, ThyssenKrupp, voestalpine), test procedures are being generated in order to be able to correctly assess properties such as corrosion resistance, adhesion, peeling-off behavior, etc. An overview of the procedures will be given together with correlations between laboratory results and reality. To round up the paper, corrosion protection primers have a number of potentials which can be utilized by the automotive industry to justify the additional cost. Examples highlighted with results giving evidence of these potentials will be shown. (orig.)

  18. Fatigue and Mechanical Damage Propagation in Automotive PEM Fuel Cells

    Science.gov (United States)

    Banan, Roshanak

    Polymer electrolyte membrane (PEM) fuel cells are generally exposed to high magnitude road-induced vibrations and impact loads, frequent humidity-temperature loading cycles, and freeze/thaw stresses when employed in automotive applications. The resultant mechanical stresses can play a significant role in the evolution of mechanical defects in the membrane electrode assembly (MEA). The focus of this research is to investigate fatigue challenges due to humidity-temperature (hygrothermal) cycles and vibrations and their effects on damage evolution in PEM fuel cells. To achieve this goal, this thesis is divided into three parts that provide insight into damage propagation in the MEA under i) hygrothermal cycles, ii) external applied vibrations, and iii) a combination of both to simulate realistic automotive conditions. A finite element damage model based on cohesive zone theory was developed to simulate the propagation of micro-scale defects (cracks and delaminations) in the MEA under fuel cell operating conditions. It was found that the micro-defects can propagate to critical states under start-up and shut-down cycles, prior to reaching the desired lifespan of the fuel cell. The simultaneous presence of hygrothermal cycles and vibrations severely intensified damage propagation and resulted in considerably large defects within 75% of the fuel cell life expectancy. However, the order of generated damage was found to be larger under hygrothermal cycles than vibrations. Under hygrothermal cycles, membrane crack propagation was more severe compared to delamination propagation. Conversely, the degrading influence of vibrations was more significant on delaminations. The presence of an anode/cathode channel offset under the combined loadings lead to a 2.5-fold increase in the delamination length compared to the aligned-channel case. The developed model can be used to investigate the damage behaviour of current materials employed in fuel cells as well as to evaluate the

  19. Mapping automotive like controls to a general aviation aircraft

    Science.gov (United States)

    Carvalho, Christopher G.

    The purpose of this thesis was to develop fly-by-wire control laws enabling a general aviation aircraft to be flown with automotive controls, i.e. a steering wheel and gas/brake pedals. There was a six speed shifter used to change the flight mode of the aircraft. This essentially allows the pilot to have control over different aspects of the flight profile such as climb/descend or cruise. A highway in the sky was used to aid in the navigation since it is not intuitive to people without flight experience how to navigate from the sky or when to climb and descend. Many believe that general aviation could become as widespread as the automobile. Every person could have a personal aircraft at their disposal and it would be as easy to operate as driving an automobile. The goal of this thesis is to fuse the ease of drivability of a car with flight of a small general aviation aircraft. A standard automotive control hardware setup coupled with variably autonomous control laws will allow new pilots to fly a plane as easily as driving a car. The idea is that new pilots will require very little training to become proficient with these controls. Pilots with little time to stay current can maintain their skills simply by driving a car which is typically a daily activity. A human factors study was conducted to determine the feasibility of the applied control techniques. Pilot performance metrics were developed to compare candidates with no aviation background and experienced pilots. After analyzing the relative performance between pilots and non-pilots, it has been determined that the control system is robust and easy to learn. Candidates with no aviation experience whatsoever can learn to fly an aircraft as safely and efficiently as someone with hundreds of hours of flight experience using these controls.

  20. Frequency weighting filter design for automotive ride comfort evaluation

    Science.gov (United States)

    Du, Feng

    2016-07-01

    Few study gives guidance to design weighting filters according to the frequency weighting factors, and the additional evaluation method of automotive ride comfort is not made good use of in some countries. Based on the regularities of the weighting factors, a method is proposed and the vertical and horizontal weighting filters are developed. The whole frequency range is divided several times into two parts with respective regularity. For each division, a parallel filter constituted by a low- and a high-pass filter with the same cutoff frequency and the quality factor is utilized to achieve section factors. The cascading of these parallel filters obtains entire factors. These filters own a high order. But, low order filters are preferred in some applications. The bilinear transformation method and the least P-norm optimal infinite impulse response(IIR) filter design method are employed to develop low order filters to approximate the weightings in the standard. In addition, with the window method, the linear phase finite impulse response(FIR) filter is designed to keep the signal from distorting and to obtain the staircase weighting. For the same case, the traditional method produces 0.330 7 m • s-2 weighted root mean square(r.m.s.) acceleration and the filtering method gives 0.311 9 m • s-2 r.m.s. The fourth order filter for approximation of vertical weighting obtains 0.313 9 m • s-2 r.m.s. Crest factors of the acceleration signal weighted by the weighting filter and the fourth order filter are 3.002 7 and 3.011 1, respectively. This paper proposes several methods to design frequency weighting filters for automotive ride comfort evaluation, and these developed weighting filters are effective.