WorldWideScience

Sample records for automatic transmissions

  1. Automatic Transmission Of Liquid Nitrogen

    Directory of Open Access Journals (Sweden)

    Sumedh Mhatre

    2015-08-01

    Full Text Available Liquid Nitrogen is one of the major substance used as a chiller in industry such as Ice cream factory Milk Diary Storage of blood sample Blood Bank etc. It helps to maintain the required product at a lower temperature for preservation purpose. We cannot fully utilise the LN2 so practically if we are using 3.75 litre LN2 for a single day then around 12 of LN2 450 ml is wasted due to vaporisation. A pressure relief valve is provided to create a pressure difference. If there is no pressure difference between the cylinder carrying LN2 and its surrounding it will results in damage of container as well as wastage of LN2.Transmission of LN2 from TA55 to BA3 is carried manually .So care must be taken for the transmission of LN2 in order to avoid its wastage. With the help of this project concept the transmission of LN2 will be carried automatically so as to reduce the wastage of LN2 in case of manual operation.

  2. Does automatic transmission improve driving behavior in older drivers?

    Science.gov (United States)

    Selander, Helena; Bolin, Ingrid; Falkmer, Torbjörn

    2012-01-01

    Most older drivers continue to drive as they age. To maintain safe and independent transport, mobility is important for all individuals, but especially for older drivers. The objective of this study was to investigate whether automatic transmission, compared with manual transmission, may improve the driving behavior of older drivers. In total, 31 older drivers (mean age 75.2 years) and 32 younger drivers - used as a control group (mean age 39.2 years) - were assessed twice on the same fixed route; once in a car with manual transmission and once in a car with automatic transmission. The cars were otherwise identical. The driving behavior was assessed with the Ryd On-Road Assessment driving protocol. Time to completion of left turns (right-hand side driving) and the impact of a distraction task were measured. The older group had more driving errors than the younger group, in both the manual and the automatic transmission car. However, and contrary to the younger drivers, automatic transmission improved the older participants' driving behavior as demonstrated by safer speed adjustment in urban areas, greater maneuvering skills, safer lane position and driving in accordance with the speed regulations. Switching to automatic transmission may be recommended for older drivers as a means to maintain safe driving and thereby the quality of their transport mobility. Copyright © 2011 S. Karger AG, Basel.

  3. Filtration ATF in automatic transmissions (AT of cars

    Directory of Open Access Journals (Sweden)

    Tadeusz Dziubak

    2014-03-01

    Full Text Available Functions and conditions of work of suction ATF filters are presented. Requirements ofATF filters are discussed. Sources of contaminations ATF are presented. ATF filtration system wascharacterized. Classification of ATF filters and their selection of design solutions are presented. Filtermaterials used for the production of ATF suction filters are presented and characterized. Conditions ofthe work of suction ATF filters were analyzed. Hydraulic and filtration characteristics are discussed.[b]Keywords: AT[/b] — automatic transmissions, ATF — automatic transmission fluid, ATF filter

  4. Evaluation of oleic acid as additive in automatic transmission fluid

    Science.gov (United States)

    Khairuldean, A. K.; Ing, T. Chiong; Bambang, S.; Baharin, T. Kamarul; Wira, J. Y.; Syahrullail, S.

    2012-06-01

    Transmission fluid has already being monopolized by petroleum oil over these years, either mineral oil or synthetic oil, the base oil originated from the crude oil. Currently, with environmental issue becomes globally concerned, it is time to move toward green technology and more to the sustainability, resource renewability and biodegradability. To respond to this challenge, a research focusing on development of environmental friendly lubricant for Automatic Transmission (AT) is conducted. In this paper, the Refined, Bleached, and Deodorized Palm-Olein (RBDPO) mixed with the Automatic Transmission Fluid (ATF), is developed and tested. The research focuses on some parameters such as anti wear and friction coefficient characteristics. The test is conducted using four ball wear tester machine to analyze anti wear of the lubricant as well as to simulate the sliding surface of gear operation inside the transmission which is the most critical operation condition for the lubricant. The method of testing is based on ASTM D4172 Test B condition for wear measurement. By comparing the experimental results between mixed lubricants and the commercial ATF, it can be seen that the palm olein is very potential to become a base oil for transmission lubricant in the future due to its promising performance of the tested physical properties.

  5. ROAD DIAGNOSING OF THE CAR WITH AUTOMATIC TRANSMISSION

    Directory of Open Access Journals (Sweden)

    Volkov, V.

    2013-06-01

    Full Text Available Because of the way of automatic transmission functioning it is possible to diagnose Honda Civic 4d by acceleration in the mode S, but not in the manual mode. When the length of the horizontal section of the road is about 500 meters, acceleration test should be executed from 60 to 100 or 120 km/h, coast-down test - from 50 or 40 km/h to 20 km/h.

  6. Comparison of First Gear Performance for Manual and Automatic Transmissions

    Directory of Open Access Journals (Sweden)

    Kyle Stottlemyer

    2011-01-01

    Full Text Available The purpose of this project is to compare the first gear performance of an automobile for both its manual and automatic transmission options. Each transmission type has a different gear ratio, which yields a different acceleration curve for each transmission throughout the torque-rpm curve of the engine. The method of integral calculus was used to find an equation which could be used to solve for time at any point in the car's acceleration. The automobile velocity versus time was then graphed to compare each transmissions acceleration trend. This process is similar to that which automotive companies may use when determining what type of transmission to pair with a particular vehicle. By observing the trends in the acceleration graphs, it was determined that there are specific advantages and disadvantages to each type of transmission. Which transmission is the “better” choice is dependent on what application the automobile will be used for (e.g. racing, day-to-day driving, towing/hauling.

  7. Multibody simulation of vehicles equipped with an automatic transmission

    Science.gov (United States)

    Olivier, B.; Kouroussis, G.

    2016-09-01

    Nowadays automotive vehicles remain as one of the most used modes of transportation. Furthermore automatic transmissions are increasingly used to provide a better driving comfort and a potential optimization of the engine performances (by placing the gear shifts at specific engine and vehicle speeds). This paper presents an effective modeling of the vehicle using the multibody methodology (numerically computed under EasyDyn, an open source and in-house library dedicated to multibody simulations). However, the transmission part of the vehicle is described by the usual equations of motion computed using a systematic matrix approach: del Castillo's methodology for planetary gear trains. By coupling the analytic equations of the transmission and the equations computed by the multibody methodology, the performances of any vehicle can be obtained if the characteristics of each element in the vehicle are known. The multibody methodology offers the possibilities to develop the vehicle modeling from 1D-motion to 3D-motion by taking into account the rotations and implementing tire models. The modeling presented in this paper remains very efficient and provides an easy and quick vehicle simulation tool which could be used in order to calibrate the automatic transmission.

  8. Automatic Transmissions and Transaxles. Auto Mechanics Curriculum Guide. Module 8. Instructor's Guide.

    Science.gov (United States)

    Hevel, David; Tannehill, Dana, Ed.

    This module is the eighth of nine modules in the competency-based Missouri Auto Mechanics Curriculum Guide. Six units cover: introduction to automatic transmission/transaxle; hydraulic control systems; transmission/transaxle diagnosis; automatic transmission/transaxle maintenance and adjustment; in-vehicle transmission repair; and off-car…

  9. The development of structures and the prospects of automatic transmissions

    Directory of Open Access Journals (Sweden)

    O. I. Girutskiy

    2014-01-01

    Full Text Available At the present stage development of transport technology has a rapid change of production models along with intensification of modification processes of vehicles, increasing number of new developments thereby providing vehicles with higher consumer qualities and competitiveness at the markets. Automation control of car transmissions is an important task. It raises the life of the engine and transmission, increased permeability and comfort due to a smoother change of torque to the drive wheels, driving off, and acceleration, etc.The article analyzes the promising schemes rotary shaft and planetary gearboxes of leading companies in the world automotive industry, the advantages of automated transmissions. It offers the prospects of creating the control systems of transmissions based on artificial intelligence methods.To design modern vehicles equipped with automatically controlled fluid transmission is a challenge. It requires various technologies to be applied using new technical solutions and scientific principles. An analysis to solve the problem of automation control of various technical objects shows that the classical theory of automatic control does not allow taking into account the diversity of vehicles operating conditions. In this regard, the effectiveness of the systems based on its scientific principles becomes often lower than expected.Implementation of modern design technology is based on a number of scientific and philosophical principles. The most important and most common of them is the principle of hierarchy, which means to structure representations of objects by degree of detailed descriptions and the principle of decomposition (blocking, which means to decompose representations of each level on the number of components (blocks with the possibility for the separate (sub-block designing.In order to create a design of control systems for the cars and synthesize its control algorithms within the framework of the developed concept

  10. Computer controllable synchronous shifting of an automatic transmission

    Science.gov (United States)

    Davis, R.I.; Patil, P.B.

    1989-08-08

    A multiple forward speed automatic transmission produces its lowest forward speed ratio when a hydraulic clutch and hydraulic brake are disengaged and a one-way clutch connects a ring gear to the transmission casing. Second forward speed ratio results when the hydraulic clutch is engaged to connect the ring gear to the planetary carrier of a second gear set. Reverse drive and regenerative operation result when an hydraulic brake fixes the planetary and the direction of power flow is reversed. Various sensors produce signals representing the torque at the output of the transmission or drive wheels, the speed of the power source, and the hydraulic pressure applied to a clutch and brake. A control algorithm produces input data representing a commanded upshift, a commanded downshift, a commanded transmission output torque, and commanded power source speed. A microprocessor processes the inputs and produces a response to them in accordance with the execution of a control algorithm. Output or response signals cause selective engagement and disengagement of the clutch and brake at a rate that satisfies the requirements for a short gear ratio change and smooth torque transfer between the friction elements. 6 figs.

  11. The Diagnostic System of A – 604 Automatic Transmission

    Directory of Open Access Journals (Sweden)

    Czaban Jaroslaw

    2014-09-01

    Full Text Available Automatic gearbox gains increasing popularity in Europe. Little interest in diagnosis of such type of transmission in Poland results from the fact of small share in the whole market of operated cars, so there is a lack of availability of special diagnostic devices. These factors cause issues of expensive repairs, often involving a replacement of subassembly to new or aftermarket one. To a small extent some prophylactic diagnostic tests are conducted, which can eliminate future gearbox system failures. In the paper, the proposition of diagnostic system of popular A - 604 gearbox was presented. The authors are seeking for the possibility of using such type of devices to functional elaboration of gearboxes after renovation. The built system pursues the drive of the researched object, connected with simulated load, where special controller, replacing the original one, is responsible for controlling gearbox operation. This way is used to evaluate the mechanic and hydraulic parts' state. Analysis of signal runs, registered during measurements lets conclude about operation correctness, where as comparison with stock data verifies the technical state of an automatic gearbox.

  12. Pressure drop – flow characteristic investigations of ATF filter in automatic transmissions (AT of cars

    Directory of Open Access Journals (Sweden)

    Tadeusz Dziubak

    2014-12-01

    Full Text Available [b]Abstract[/b]. Potentials effects of pressure drop-flow characteristics of ATF filter on the hydraulic pumps are discussed. Draft device to investigations pressure drop-flow characteristics of ATF filter used in automatic transmissions constructed based on SAE J2312 standard is presented. Method of investigation pressure drop-flow characteristics of ATF filter used in automatic transmission is presented. The results of investigation pressure drop-flow characteristics Δp = f(QV of two types ATF filter (metal mesh and filter cloth in two technical conditions (at the beginning of the operation and after are presented and analyzed.[b]Keywords[/b]: AT — automatic transmissions, ATF — automatic transmission fluid, ATF filter, pressure drop-flow characteristic

  13. Proposal of the Measurement Method of the Transmission Line Constants by Automatic Oscillograph Utilization

    Science.gov (United States)

    Ooura, Yoshifumi

    The author devised new method for measurement of the transmission line constants of high precision with the automatic oscillograph. This paper is proposal of new method for measurement of the transmission line constants. The author utilized that the inherent eigenvector matrixs of transmission line had an equal relation with four-terminal constants eigenvector matrixs of transmission line. And the author calculated four-terminal constants of transmission line from the data (voltage-current data of the automatic oscillograph) of six cases of transmission line system faults and devised the method for measurement for transmission line constants from analysis of the four-terminal constants of transmission line next. Furthermore, the author inspected this new method in the system fault simulations of the EMTP transmission line system model. It was shown that the result is the measurement method of high accuracy. From now on, the author advances the measurement of the transmission line constants from actual system faults data of the transmission line and its periphery with the cooperation power system companies.

  14. Automatic remote monitoring utilizing daily transmissions: transmission reliability and implantable cardioverter defibrillator battery longevity in the TRUST trial.

    Science.gov (United States)

    Varma, Niraj; Love, Charles J; Schweikert, Robert; Moll, Philip; Michalski, Justin; Epstein, Andrew E

    2017-05-10

    Benefits of automatic remote home monitoring (HM) among implantable cardioverter defibrillator (ICD) patients may require high transmission frequency. However, transmission reliability and effects on battery longevity remain uncertain. We hypothesized that HM would have high transmission success permitting punctual guideline based follow-up, and improve battery longevity. This was tested in the prospective randomized TRUST trial. Implantable cardioverter defibrillator patients were randomized post-implant 2:1 to HM (n = 908) (transmit daily) or to Conventional in-person monitoring [conventional management (CM), n = 431 (HM disabled)]. In both groups, five evaluations were scheduled every 3 months for 15 months. Home Monitoring technology performance was assessed by transmissions received vs. total possible, and number of scheduled HM checks failing because of missed transmissions. Battery longevity was compared in HM vs. CM at 15 months, and again in HM 3 years post-implant using continuously transmitted data. Transmission success per patient was 91% (median follow-up of 434 days). Overall, daily HM transmissions were received in 315 795 of a potential 363 450 days (87%). Only 55/3759 (1.46%) of unsuccessful scheduled evaluations in HM were attributed to transmission loss. Shock frequency and pacing percentage were similar in HM vs. CM. Fifteen month battery longevity was 12% greater in HM (93.2 ± 8.8% vs. 83.5 ± 6.0% CM, P battery longevity was 50.9 ± 9.1% (median 52%) at 36 months. Automatic remote HM demonstrated robust transmission reliability. Daily transmission load may be sustained without reducing battery longevity. Home Monitoring conserves battery longevity and tracks long term device performance. ClinicalTrials.gov; NCT00336284.

  15. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT X, AUTOMATIC TRANSMISSIONS--HYDRAULIC SYSTEMS (PART II).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO PROVIDE A SUMMARY OF MAINTENANCE PROCEDURES FOR AUTOMATIC TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) CHECKING THE HYDRAULIC SYSTEM, (2) SERVICING THE HYDRAULIC SYSTEM, (3) EXAMINING THE RANGE CONTROL VALVE, (4) EXAMINING THE LOCK-UP AND FLOW VALVE, (5) EXAMINING THE MAIN REGULATOR…

  16. Automatic transmission parameters measurement and radiation pattern simulation for an RF photonic integrated beamformer

    NARCIS (Netherlands)

    Burla, M.; Lavabre, E.; Roeloffzen, C.G.H.; Marpaung, D.A.I.; Zhuang, L.; Khan, M.R.H.; van Etten, Wim

    2011-01-01

    We present the implementation and demonstration of a software tool for the performance characterization of integrated N-by-1 photonic beamformers for phased array antennas. The software operates the automatic measurement of the transmission parameters of an equivalent N+1 ports microwave network,

  17. A method of applying two-pump system in automatic transmissions for energy conservation

    Directory of Open Access Journals (Sweden)

    Peng Dong

    2015-06-01

    Full Text Available In order to improve the hydraulic efficiency, modern automatic transmissions tend to apply electric oil pump in their hydraulic system. The electric oil pump can support the mechanical oil pump for cooling, lubrication, and maintaining the line pressure at low engine speeds. In addition, the start–stop function can be realized by means of the electric oil pump; thus, the fuel consumption can be further reduced. This article proposes a method of applying two-pump system (one electric oil pump and one mechanical oil pump in automatic transmissions based on the forward driving simulation. A mathematical model for calculating the transmission power loss is developed. The power loss transfers to heat which requires oil flow for cooling and lubrication. A leakage model is developed to calculate the leakage of the hydraulic system. In order to satisfy the flow requirement, a flow-based control strategy for the electric oil pump is developed. Simulation results of different driving cycles show that there is a best combination of the size of electric oil pump and the size of mechanical oil pump with respect to the optimal energy conservation. Besides, the two-pump system can also satisfy the requirement of the start–stop function. This research is extremely valuable for the forward design of a two-pump system in automatic transmissions with respect to energy conservation and start–stop function.

  18. Electronic control of a 4-speed automatic transmission with lock-up clutch

    Energy Technology Data Exchange (ETDEWEB)

    Schwab, M.

    1984-01-01

    The paper describes the electronic control of an automatic 4-speed transmission with lock-up clutch. As compared to purely hydraulically controlled transmissions, this control offers a clearly improved quality of shifting and the possibility of achieving improvements in fuel consumption thanks to a special economy program. The electronic control unit is a Bosch MOTRONIC which has been expanded to include the functions of transmission control. A special feature is the engine torque control which is implemented by way of retarding the ignition when shifting. This opens up an additional degree of freedom for optimizing a transmission in terms of shift comfort, life of the friction elements and the power which can be transmitted.

  19. STUDY OF TRANSMISSION LINES EFFECT ON THE SYSTEM OPERATIONON OF CONTINUOUS AUTOMATIC CAB SIGNALLING

    Directory of Open Access Journals (Sweden)

    O. O. Hololobova

    2014-10-01

    Full Text Available Purpose. To conduct an effect research of the electromagnetic field of high-voltage transmission lines (HVTL (750 kV, 50 Hz on the track circuits and continuous automatic cab signalling (CACS with a signal current of 50 Hz in the areas of convergence and intersection with the transmission lines and to propose possible methods to improve noise immunity of CACS. Methodology. The measurements were performed both by means of car-laboratory and directly on rail lines. During the study the electric field strength in the range of industrial frequency directly under the transmission lines and at the distance from it to the railway lines was measured, as well as the time dependence of CACS codes with signal current frequency of 50 Hz directly under the transmission lines and at a distance from it in the absence of the train and its passing. Findings. The root causes analysis of CACS faults and failures was carried out. The effect of the electromagnetic field of high-voltage transmission lines (750 kV, 50 Hz on the track circuit and CACS with signal current of 50 Hz in the areas of convergence and intersection with the transmission line was investigated. Possible methods to improve noise immunity of CACS were considered. Originality. The effect research of transmission lines (750 kV on the operation of the automatic cab signalling on spans Prishib-Burchatsk and Privolnoye-Yelizarovo, Pridneprovsk railway in places of oblique railroads crossing and transmission lines (750 kV, 50 Hz was conducted. Electric field strength in the range of industrial frequency directly under the transmission lines and at a distance from it to the railway line, as well as the time dependences of ALSN codes with signal current frequency of 50 Hz directly under the transmission lines and at a distance from it in the absence of the train and as its passing were measured. It was found that CACS codes in track circuits under transmission lines are strongly distorted, as strength

  20. Lightning Protection Performance Assessment of Transmission Line Based on ATP model Automatic Generation

    Directory of Open Access Journals (Sweden)

    Luo Hanwu

    2016-01-01

    Full Text Available This paper presents a novel method to solve the initial lightning breakdown current by combing ATP and MATLAB simulation software effectively, with the aims to evaluate the lightning protection performance of transmission line. Firstly, the executable ATP simulation model is generated automatically according to the required information such as power source parameters, tower parameters, overhead line parameters, grounding resistance and lightning current parameters, etc. through an interface program coded by MATLAB. Then, the data are extracted from the generated LIS files which can be obtained by executing the ATP simulation model, the occurrence of transmission lie breakdown can be determined by the relative data in LIS file. The lightning current amplitude should be reduced when the breakdown occurs, and vice the verse. Thus the initial lightning breakdown current of a transmission line with given parameters can be determined accurately by continuously changing the lightning current amplitude, which is realized by a loop computing algorithm that is coded by MATLAB software. The method proposed in this paper can generate the ATP simulation program automatically, and facilitates the lightning protection performance assessment of transmission line.

  1. Possibilities for Automatic Control of Hydro-Mechanical Transmission and Birotating Electric Machine

    Directory of Open Access Journals (Sweden)

    V. V. Mikhailov

    2014-01-01

    Full Text Available The paper presents mathematical models and results of virtual investigations pertaining to the selected motion parameters of a mobile machine equipped with hydro mechanical and modernized transmissions. The machine has been tested in similar technological cycles and it has been equipped with a universal automatic control system. Changes in structure and type of power transmission have been obtained with the help of a control algorithm including an extra reversible electric machine which is switched in at some operational modes.Implementation of the proposed  concept makes it possible to obtain and check the improved C-code of the control system and enhance operational parameters of the transmission and machine efficiency, reduce slippage and tire wear while using braking energy for its later beneficial use which is usually considered as a consumable element.

  2. To the problem of topological optimization of data processing and transmission networks in development of the automatic control system ''Atom''

    International Nuclear Information System (INIS)

    Gal'berg, V.P.

    1981-01-01

    Some optimization problems occurring in developing the automatic control system (ASC) of a commercial amalgamation (ACS-ATOM), assessments of economically optimal structure of location of computation centres and means of data transmission in particular are considered [ru

  3. Clutch fill control of an automatic transmission for heavy-duty vehicle applications

    Science.gov (United States)

    Meng, Fei; Chen, Huiyan; Zhang, Tao; Zhu, Xiaoyuan

    2015-12-01

    In this paper an integrated clutch filling phase control for gearshifts on wet clutch transmissions is developed. In a clutch-to-clutch shift of an automatic transmission, in order to obtain smooth gearshift, it should synchronize the oncoming clutch and the off-going clutch timely as well as precise pressure control for the engagement of the oncoming clutch. However, before the oncoming clutch pressure starts to increase, the initial cavity of the clutch chamber has to be filled first. The filling time and stability of the fill phase are very important for the clutch control. In order to improve the shift quality of the automatic transmission which is equipped on heavy-duty vehicles, the electro-hydraulic clutch actuation system is analysed and modelled. A new fill phase control strategy is proposed based on the system analysis as well as the control parameters are optimized according to the variation of the oil temperature and engine speed. The designed strategy is validated by a simulation work. The results demonstrate that the proposed control strategy and parameters modified method can transit the shift process from the fill phase to the torque phase effectively.

  4. Forming and detection of digital watermarks in the System for Automatic Identification of VHF Transmissions

    Directory of Open Access Journals (Sweden)

    О. В. Шишкін

    2013-07-01

    Full Text Available Forming and detection algorithms for digital watermarks are designed for automatic identification of VHF radiotelephone transmissions in the maritime and aeronautical mobile services. An audible insensitivity and interference resistance of embedded digital data are provided by means of OFDM technology jointly with normalized distortions distribution and data packet detection by the hash-function. Experiments were carried out on the base of ship’s radio station RT-2048 Sailor and USB ADC-DAC module of type Е14-140M L-CARD in the off-line processing regime in Matlab medium

  5. Transmission History Based Distributed Adaptive Contention Window Adjustment Algorithm Cooperating with Automatic Rate Fallback for Wireless LANs

    Science.gov (United States)

    Ogawa, Masakatsu; Hiraguri, Takefumi; Nishimori, Kentaro; Takaya, Kazuhiro; Murakawa, Kazuo

    This paper proposes and investigates a distributed adaptive contention window adjustment algorithm based on the transmission history for wireless LANs called the transmission-history-based distributed adaptive contention window adjustment (THAW) algorithm. The objective of this paper is to reduce the transmission delay and improve the channel throughput compared to conventional algorithms. The feature of THAW is that it adaptively adjusts the initial contention window (CWinit) size in the binary exponential backoff (BEB) algorithm used in the IEEE 802.11 standard according to the transmission history and the automatic rate fallback (ARF) algorithm, which is the most basic algorithm in automatic rate controls. This effect is to keep CWinit at a high value in a congested state. Simulation results show that the THAW algorithm outperforms the conventional algorithms in terms of the channel throughput and delay, even if the timer in the ARF is changed.

  6. Analysis of Relationship between Pioneer Brand Status and Consumer’s Attitude toward a Brand (Case on Yamaha Automatic vs. Honda Automatic Transmission Motorcycle in Indonesia

    Directory of Open Access Journals (Sweden)

    Arga Hananto

    2011-06-01

    Full Text Available Previous research have indicated that brand pioneership provide some advantages such as high market share barriers to entry and consumers preference as well as higher consumer attitude. This paper intends to explore the relationship between perceived brand pioneership on consumers’ brand attitude. The study focuses on two competing brands from automatic transmission motorcycle category, namely Yamaha and Honda.Based on result from 90 respondents, this study confirms the perception that Yamaha (although not the true pioneer is perceived by the majority of respondents as the pioneering brand in the automatic transmission motorcycle. This study also found that those respondents who perceived that Yamaha is the pioneer brand tend to ascribe higher brand attitude toward Yamaha than toward Honda. Result from this study adds to the repository of studies concerning brand pioneership as well as adding to repository of knowledge about Indonesian consumer behavior.

  7. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT VII, AUTOMATIC TRANSMISSIONS--ALLISON, TORQUMATIC SERIES 5960 AND 6060 (PART I).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF SPECIFIC MODELS OF AUTOMATIC TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) GENERAL SPECIFICATION DATA, (2) OPTIONS FOR VARIOUS APPLICATIONS, (3) ROAD TEST INSTRUCTIONS, (4) IDENTIFICATION AND SPECIFICATION DATA, (5) ALLISON…

  8. A turbo engine with automatic transmission? How to many chemicomotion to the subtleties and robustness of life

    DEFF Research Database (Denmark)

    Koefoed, S.; Otten, M.F.; Købmann, Brian Jensen

    2002-01-01

    benefits of the turbo-charging of catabolic pathways, of loose coupling, low-gear catabolism, automatic transmission in energy coupling, and of homeostasis. Mechanisms for such phenomena may reside at the level of individual proton pumps, or consist of rerouting of electrons over parallel pathways...

  9. Optimization of a pressure control valve for high power automatic transmission considering stability

    Science.gov (United States)

    Jian, Hongchao; Wei, Wei; Li, Hongcai; Yan, Qingdong

    2018-02-01

    The pilot-operated electrohydraulic clutch-actuator system is widely utilized by high power automatic transmission because of the demand of large flowrate and the excellent pressure regulating capability. However, a self-excited vibration induced by the inherent non-linear characteristics of valve spool motion coupled with the fluid dynamics can be generated during the working state of hydraulic systems due to inappropriate system parameters, which causes sustaining instability in the system and leads to unexpected performance deterioration and hardware damage. To ensure a stable and fast response performance of the clutch actuator system, an optimal design method for the pressure control valve considering stability is proposed in this paper. A non-linear dynamic model of the clutch actuator system is established based on the motion of the valve spool and coupling fluid dynamics in the system. The stability boundary in the parameter space is obtained by numerical stability analysis. Sensitivity of the stability boundary and output pressure response time corresponding to the valve parameters are identified using design of experiment (DOE) approach. The pressure control valve is optimized using particle swarm optimization (PSO) algorithm with the stability boundary as constraint. The simulation and experimental results reveal that the optimization method proposed in this paper helps in improving the response characteristics while ensuring the stability of the clutch actuator system during the entire gear shift process.

  10. The FAST-DATA System: Fully Automatic Stochastic Technology for Data Acquisition, Transmission, and Analysis

    International Nuclear Information System (INIS)

    Albrecht, R.W.; Crowe, R.D.; McGuire, J.J.

    1978-01-01

    The potential to automatically collect, classify, and report on stochastic data (signals with random, time-varying components) from power plants has long been discussed by utilities, government, industries, national laboratories and universities. It has become clear to all concerned that such signals often contain information about plant conditions which may provide the basis for increased plant availability through early detection and warning of developing malfunctions. Maintenance can then be scheduled at opportune times. Inopportune failures of major and minor power plant components are a major cause of down-time and detracts significantly from availability of the plant. A complete system to realize automatic stochastic data processing has been conceptually designed. Development of the FAST-DATA system has been initiated through a program of periodic measurements performed on the vibration and loose parts monitoring system of the Trojan reactor (1130-MW(e)PWR) operated by Portland General Electric Company. The development plan for the system consists of a six-step procedure. The initial steps depend on a significant level of human involvement. In the course of development of the system, the routine duties of operators and analysts are gradually replaced by computerized automatic data handling procedures. In the final configuration, the operator and analysts are completely freed of routine chores by logical machinery. The results achieved to date from actual application of the proof-of-principle system are discussed. The early developmental phases have concentrated on system organization and examination of a representative data base. Preliminary results from the signature analysis program using Trojan data indicate that the performance specifications predicted for the FAST-DATA system are achievable in practice. (author)

  11. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT III, AUTOMATIC TRANSMISSIONS--HYDRAULICS (PART I).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO INTRODUCE BASIC HYDRAULIC PRINCIPLES AND PROVIDE AN UNDERSTANDING OF HYDRAULIC TRANSMISSIONS USED IN DIESEL POWERED VEHICLES. TOPICS ARE WHY USE HYDRAULICS, REVIEWING BASIC PHYSICS LAWS IN RELATION TO HYDRAULICS, UNDERSTANDING THE HYDRAULIC SYSTEM, AND DEVELOPING A BASIC HYDRAULIC SYSTEM. THE MODULE…

  12. AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT IX, AUTOMATIC TRANSMISSIONS--HYDRAULIC SYSTEM (PART I).

    Science.gov (United States)

    Human Engineering Inst., Cleveland, OH.

    THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OIL FLOW WITHIN HYDRAULIC TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE GENERAL DESCRIPTION, HYDRAULIC CIRCUITS, AND BRAKE HYDRAULIC CIRCUIT AND OPERATION. THE MODULE CONSISTS OF A SELF-INSTRUCTIONAL PROGRAMED TRAINING FILM "LEARNING ABOUT THE ALLISON…

  13. A Novel, Automatic Quality Control Scheme for Real Time Image Transmission

    Directory of Open Access Journals (Sweden)

    S. Ramachandran

    2002-01-01

    Full Text Available A novel scheme to compute energy on-the-fly and thereby control the quality of the image frames dynamically is presented along with its FPGA implementation. This scheme is suitable for incorporation in image compression systems such as video encoders. In this new scheme, processing is automatically stopped when the desired quality is achieved for the image being processed by using a concept called pruning. Pruning also increases the processing speed by a factor of more than two when compared to the conventional method of processing without pruning. An MPEG-2 encoder implemented using this scheme is capable of processing good quality monochrome and color images of sizes up to 1024 × 768 pixels at the rate of 42 and 28 frames per second, respectively, with a compression ratio of over 17:1. The encoder is also capable of working in the fixed pruning level mode with user programmable features.

  14. Automatic Assessment of Acquisition and Transmission Losses in Indian Remote Sensing Satellite Data

    Science.gov (United States)

    Roy, D.; Purna Kumari, B.; Manju Sarma, M.; Aparna, N.; Gopal Krishna, B.

    2016-06-01

    The quality of Remote Sensing data is an important parameter that defines the extent of its usability in various applications. The data from Remote Sensing satellites is received as raw data frames at the ground station. This data may be corrupted with data losses due to interferences during data transmission, data acquisition and sensor anomalies. Thus it is important to assess the quality of the raw data before product generation for early anomaly detection, faster corrective actions and product rejection minimization. Manual screening of raw images is a time consuming process and not very accurate. In this paper, an automated process for identification and quantification of losses in raw data like pixel drop out, line loss and data loss due to sensor anomalies is discussed. Quality assessment of raw scenes based on these losses is also explained. This process is introduced in the data pre-processing stage and gives crucial data quality information to users at the time of browsing data for product ordering. It has also improved the product generation workflow by enabling faster and more accurate quality estimation.

  15. Parameter design and performance analysis of shift actuator for a two-speed automatic mechanical transmission for pure electric vehicles

    Directory of Open Access Journals (Sweden)

    Jianjun Hu

    2016-08-01

    Full Text Available Recent developments of pure electric vehicles have shown that pure electric vehicles equipped with two-speed or multi-speed gearbox possess higher energy efficiency by ensuring the drive motor operates at its peak performance range. This article presents the design, analysis, and control of a two-speed automatic mechanical transmission for pure electric vehicles. The shift actuator is based on a motor-controlled camshaft where a special geometric groove is machined, and the camshaft realizes the axial positions of the synchronizer sleeve for gear engaging, disengaging, and speed control of the drive motor. Based on the force analysis of shift process, the parameters of shift actuator and shift motor are designed. The drive motor’s torque control strategy before shifting, speed governing control strategy before engaging, shift actuator’s control strategy during gear engaging, and drive motor’s torque recovery strategy after shift process are proposed and implemented with a prototype. To validate the performance of the two-speed gearbox, a test bed was developed based on dSPACE that emulates various operation conditions. The experimental results indicate that the shift process with the proposed shift actuator and control strategy could be accomplished within 1 s under various operation conditions, with shift smoothness up to passenger car standard.

  16. Fault prevention by early stage symptoms detection for automatic vehicle transmission using pattern recognition and curve fitting

    Science.gov (United States)

    Balbin, Jessie R.; Cruz, Febus Reidj G.; Abu, Jon Ervin A.; Siño, Carlo G.; Ubaldo, Paolo E.; Zulueta, Christelle Jianne T.

    2017-06-01

    Automobiles have become essential parts of our everyday lives. It can correlate many factors that may affect a vehicle primarily those which may inconvenient or in some cases harm lives or properties. Thus, focusing on detecting an automatic transmission vehicle engine, body and other parts that cause vibration and sound may help prevent car problems using MATLAB. By using sound, vibration, and temperature sensors to detect the defects of the car and with the help of the transmitter and receiver to gather data wirelessly, it is easy to install on to the vehicle. A technique utilized from Toyota Balintawak Philippines that every car is treated as panels(a, b, c, d, and e) 'a' being from the hood until the front wheel of the car and 'e' the rear shield to the back of the car, this was applied on how to properly place the sensors so that precise data could be gathered. Data gathered would be compared to the normal graph taken from the normal status or performance of a vehicle, data that would surpass 50% of the normal graph would be considered that a problem has occurred. The system is designed to prevent car accidents by determining the current status or performance of the vehicle, also keeping people away from harm.

  17. Convective Heat Transfer Coefficients of Automatic Transmission Fluid Jets with Implications for Electric Machine Thermal Management: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Bennion, Kevin; Moreno, Gilberto

    2015-09-29

    Thermal management for electric machines (motors/ generators) is important as the automotive industry continues to transition to more electrically dominant vehicle propulsion systems. Cooling of the electric machine(s) in some electric vehicle traction drive applications is accomplished by impinging automatic transmission fluid (ATF) jets onto the machine's copper windings. In this study, we provide the results of experiments characterizing the thermal performance of ATF jets on surfaces representative of windings, using Ford's Mercon LV ATF. Experiments were carried out at various ATF temperatures and jet velocities to quantify the influence of these parameters on heat transfer coefficients. Fluid temperatures were varied from 50 degrees C to 90 degrees C to encompass potential operating temperatures within an automotive transaxle environment. The jet nozzle velocities were varied from 0.5 to 10 m/s. The experimental ATF heat transfer coefficient results provided in this report are a useful resource for understanding factors that influence the performance of ATF-based cooling systems for electric machines.

  18. Modeling of uniform moving of a vehicle equipped with automatical transmission, based on the gear-lever variator

    OpenAIRE

    Ternyuk, N.; Krasnoshtan, A.

    2006-01-01

    The analyses of a uniform drive of a vehicle equipped with a continuonsly variable transmission fased on the gear-lever vibrator has been done a functional dependence of the parameters of a uniform drive (speed) on construction a vehicle have been analysed. The basic functional dependence between these parameters have been presented.

  19. Small passenger car transmission test: Mercury Lynx ATX transmission

    Science.gov (United States)

    Bujold, M. P.

    1981-01-01

    The testing of a Mercury Lynx automatic transmission is reported. The transmission was tested in accordance with a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these conditions, the transmission attained maximum efficiencies in the mid-ninety percent range both for drive performance test and coast performance tests. The torque, speed, and efficiency curves are presented, which provide the complete performance characteristics for the Mercury Lynx automatic transmission.

  20. Automatic sequences

    CERN Document Server

    Haeseler, Friedrich

    2003-01-01

    Automatic sequences are sequences which are produced by a finite automaton. Although they are not random they may look as being random. They are complicated, in the sense of not being not ultimately periodic, they may look rather complicated, in the sense that it may not be easy to name the rule by which the sequence is generated, however there exists a rule which generates the sequence. The concept automatic sequences has special applications in algebra, number theory, finite automata and formal languages, combinatorics on words. The text deals with different aspects of automatic sequences, in particular:· a general introduction to automatic sequences· the basic (combinatorial) properties of automatic sequences· the algebraic approach to automatic sequences· geometric objects related to automatic sequences.

  1. Automated manual transmission controller

    Science.gov (United States)

    Lawrie, Robert E.; Reed, Jr., Richard G.; Bernier, David R.

    1999-12-28

    A powertrain system for a hybrid vehicle. The hybrid vehicle includes a heat engine, such as a diesel engine, and an electric machine, which operates as both an electric motor and an alternator, to power the vehicle. The hybrid vehicle also includes a manual-style transmission configured to operate as an automatic transmission from the perspective of the driver. The engine and the electric machine drive an input shaft which in turn drives an output shaft of the transmission. In addition to driving the transmission, the electric machine regulates the speed of the input shaft in order to synchronize the input shaft during either an upshift or downshift of the transmission by either decreasing or increasing the speed of the input shaft. When decreasing the speed of the input shaft, the electric motor functions as an alternator to produce electrical energy which may be stored by a storage device. Operation of the transmission is controlled by a transmission controller which receives input signals and generates output signals to control shift and clutch motors to effect smooth launch, upshift shifts, and downshifts of the transmission, so that the transmission functions substantially as an automatic transmission from the perspective of the driver, while internally substantially functioning as a manual transmission.

  2. Small passenger car transmission test; Chevrolet LUV transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    A 1978 Chevrolet LUV manual transmission tested per the applicable portions of a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions, the transmission attained maximum efficiencies in the upper ninety percent range for both drive performance tests and coast performance tests. The major results of this test (torque, speed, and efficiency curves) are presented. Graphs map the complete performance characteristics for the Chevrolet LUV transmission.

  3. Small passenger car transmission test-Chevrolet 200 transmission

    Science.gov (United States)

    Bujold, M. P.

    1980-01-01

    The small passenger car transmission was tested to supply electric vehicle manufacturers with technical information regarding the performance of commerically available transmissions which would enable them to design a more energy efficient vehicle. With this information the manufacturers could estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. A 1979 Chevrolet Model 200 automatic transmission was tested per a passenger car automatic transmission test code (SAE J651b) which required drive performance, coast performance, and no load test conditions. The transmission attained maximum efficiencies in the mid-eighty percent range for both drive performance tests and coast performance tests. Torque, speed and efficiency curves map the complete performance characteristics for Chevrolet Model 200 transmission.

  4. The construction of the CMS electromagnetic calorimeter: automatic measurements of the physics parameters of PWO crystals

    CERN Multimedia

    2005-01-01

    Crystal properties (dimensions, optical transmission, light yield) are automatically measured. The pictures show different measurement stations of the automatic machine. Crystals are measured on trays containing five crystals each.

  5. Research on wireless communication technology based on automatic logistics system of welder

    Directory of Open Access Journals (Sweden)

    Sun Xuan

    2018-01-01

    Full Text Available In order to meet the requirements of high real-time and high stability of data transmission in automatic welding system, RTU data format and real-time communication mechanism are adopted in this system. In the automatic logistics system through the Ethernet and wireless WIFI technology will palletizer, stacker, AGV car organically together to complete the palletizer automatic crawling the goods, AGV car automatic delivery, stacking machine automatically out of the Dimensional warehouse. .

  6. Research on wireless communication technology based on automatic logistics system of welder

    OpenAIRE

    Sun Xuan; Wang Zhi-yong; Ma Zhe-dong

    2018-01-01

    In order to meet the requirements of high real-time and high stability of data transmission in automatic welding system, RTU data format and real-time communication mechanism are adopted in this system. In the automatic logistics system through the Ethernet and wireless WIFI technology will palletizer, stacker, AGV car organically together to complete the palletizer automatic crawling the goods, AGV car automatic delivery, stacking machine automatically out of the Dimensional warehouse. .

  7. Physics of Automatic Target Recognition

    CERN Document Server

    Sadjadi, Firooz

    2007-01-01

    Physics of Automatic Target Recognition addresses the fundamental physical bases of sensing, and information extraction in the state-of-the art automatic target recognition field. It explores both passive and active multispectral sensing, polarimetric diversity, complex signature exploitation, sensor and processing adaptation, transformation of electromagnetic and acoustic waves in their interactions with targets, background clutter, transmission media, and sensing elements. The general inverse scattering, and advanced signal processing techniques and scientific evaluation methodologies being used in this multi disciplinary field will be part of this exposition. The issues of modeling of target signatures in various spectral modalities, LADAR, IR, SAR, high resolution radar, acoustic, seismic, visible, hyperspectral, in diverse geometric aspects will be addressed. The methods for signal processing and classification will cover concepts such as sensor adaptive and artificial neural networks, time reversal filt...

  8. 49 CFR 571.102 - Standard No. 102; Transmission shift position sequence, starter interlock, and transmission...

    Science.gov (United States)

    2010-10-01

    ... OF TRANSPORTATION FEDERAL MOTOR VEHICLE SAFETY STANDARDS Federal Motor Vehicle Safety Standards § 571... position. S3.1.2Transmission braking effect. In vehicles having more than one forward transmission gear... when the transmission shift position is in any forward drive gear; (b) The engine may not automatically...

  9. Small passenger car transmission test: Mercury Lynx ATX transmission

    Energy Technology Data Exchange (ETDEWEB)

    Bujold, M P

    1981-09-01

    The small passenger car transmission test was initiated to supply electric vehicle manufacturers with technical information regarding the performance of commercially available transmissions. This information would enable EV manufacturers to design a more energy efficient vehicle. With this information the manufacturers would be able to estimate vehicle driving range as well as speed and torque requirements for specific road load performance characteristics. This report covers the 1981 Mercury Lynx ATX transaxle. This transmission was tested per a passenger car automatic transmission test code (SAE J65lb) which required drive performance, coast performance, and no load test conditions. Under these test conditions the transmission attained maximum efficiencies in the 93% range for drive performance tests. The major results of this test are the torque, speed and efficiency curves which are located in the data section of this report. These graphs map performance characteristics for the Mercury Lynx ATX transmission.

  10. Automatic fluid dispenser

    Science.gov (United States)

    Sakellaris, P. C. (Inventor)

    1977-01-01

    Fluid automatically flows to individual dispensing units at predetermined times from a fluid supply and is available only for a predetermined interval of time after which an automatic control causes the fluid to drain from the individual dispensing units. Fluid deprivation continues until the beginning of a new cycle when the fluid is once again automatically made available at the individual dispensing units.

  11. Transmissions in vehicles 2010

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2010-07-01

    Within the international VDI congress 'Gears in vehicles 2010' of the VDI Wissensforum GmbH (Duesseldorf, Federal Republic of Germany) between 22nd and 23rd June, 2010, in Friedrichshafen (Federal Republic of Germany), the following lectures were held: (1) 8HP70H - The moldhybrid transmission from ZF - Cjallenges and achievements (P. Gutmann); (2) GETRAG boosted range extender - A highly flexible electric powertrain for maximum CO{sub 2} reduction (S. Huepkes); (3) E-Transmission between full-hybrid and E-drive (P. Tenberge); (4) Reducing NO{sub x} and particulate emissions in electrified drivelines (R. Kuberczyk); (5) Simulation aided HEV and EV development: from the component to the whole powertrain (A. Gacometti); (6) Investigations on operating behaviour of the optimized CVT hybrid driveline (B.-R. Hoehn); (7) Customer-oriented dimensioning of electrified drivetrains (M. Eghtessad); (8) Decentralized optimal control strategy for parallel hybrid electric vehicles (A. Frenkel); (9) The new generation 6-speed automatic transmission AF40 (G. Bednarek); (10) Customized mechatronic solutions for integrated transmission control units (M. Wieczorek); (11) The optimal automatic transmission for front-transverse applications - Planetary transmissions or dual clutch transmissions? (G. Gumpoltsberger); (12) The new shift-by-wire gearshift lever for the Audi A8 - Requirements and concept (T. Guttenbergere); (13) The new shift-by-wire gearshift lever for the Audi A8 - Realization (A. Giefer); (14) Fuel-efficient transmissions of the future: Calculation of the efficiency factor for vehicle transmissions (B. Volpert); (15) HT-ACM: A new polymer generation for static and dynamic gearbox sealing solutions (E. Osen); (16) 'Energy efficiency equipped solutions by SKF' for power train applications - A contribution to CO{sub 2} - emission reduction and sustainability (T. Bobke); (17) 6-Ratio planetary shift transmission controlled by 4 external brakes, and design

  12. Automatic Fiscal Stabilizers

    Directory of Open Access Journals (Sweden)

    Narcis Eduard Mitu

    2013-11-01

    Full Text Available Policies or institutions (built into an economic system that automatically tend to dampen economic cycle fluctuations in income, employment, etc., without direct government intervention. For example, in boom times, progressive income tax automatically reduces money supply as incomes and spendings rise. Similarly, in recessionary times, payment of unemployment benefits injects more money in the system and stimulates demand. Also called automatic stabilizers or built-in stabilizers.

  13. Automatic differentiation bibliography

    Energy Technology Data Exchange (ETDEWEB)

    Corliss, G.F. (comp.)

    1992-07-01

    This is a bibliography of work related to automatic differentiation. Automatic differentiation is a technique for the fast, accurate propagation of derivative values using the chain rule. It is neither symbolic nor numeric. Automatic differentiation is a fundamental tool for scientific computation, with applications in optimization, nonlinear equations, nonlinear least squares approximation, stiff ordinary differential equation, partial differential equations, continuation methods, and sensitivity analysis. This report is an updated version of the bibliography which originally appeared in Automatic Differentiation of Algorithms: Theory, Implementation, and Application.

  14. Transmission issues

    International Nuclear Information System (INIS)

    Bradford, J.; Wilson, L.; Thon, S.; Millar, N.

    2005-01-01

    This session on transmission issues focused on the role that transmission plays in electricity markets and the importance of getting the market structure right in terms of generation divestiture with buy back contracts, demand side responsive programs, transmission upgrades and long term contracts. The difficulties of distinguishing between market power and scarcity were examined along with some of the complications that ensue if transmission experiences congestion, as exemplified by the August 2003 blackout in eastern North America. The presentations described the best ways to handle transmission issues, and debated whether transmission should be deregulated or follow market forces. Issues of interconnections and reliability of connections were also debated along with the attempt to integrate renewables into the grid. Some presentations identified what new transmission must be built and what must be done to ensure that transmission gets built. The challenges and business opportunities for transmission in Alberta were discussed with reference to plans to invest in new infrastructure, where it is going outside of the province and how it works with other jurisdictions. Manitoba's Conawapa Hydro Project and its 2000 MW tie line to Ontario was also discussed. Some examples of non-optimal use of interconnections in Europe were also discussed in an effort to learn from these mistakes and avoid them in Canada. tabs., figs

  15. Automatic control systems engineering

    International Nuclear Information System (INIS)

    Shin, Yun Gi

    2004-01-01

    This book gives descriptions of automatic control for electrical electronics, which indicates history of automatic control, Laplace transform, block diagram and signal flow diagram, electrometer, linearization of system, space of situation, state space analysis of electric system, sensor, hydro controlling system, stability, time response of linear dynamic system, conception of root locus, procedure to draw root locus, frequency response, and design of control system.

  16. Neural Bases of Automaticity

    Science.gov (United States)

    Servant, Mathieu; Cassey, Peter; Woodman, Geoffrey F.; Logan, Gordon D.

    2018-01-01

    Automaticity allows us to perform tasks in a fast, efficient, and effortless manner after sufficient practice. Theories of automaticity propose that across practice processing transitions from being controlled by working memory to being controlled by long-term memory retrieval. Recent event-related potential (ERP) studies have sought to test this…

  17. Focusing Automatic Code Inspections

    NARCIS (Netherlands)

    Boogerd, C.J.

    2010-01-01

    Automatic Code Inspection tools help developers in early detection of defects in software. A well-known drawback of many automatic inspection approaches is that they yield too many warnings and require a clearer focus. In this thesis, we provide such focus by proposing two methods to prioritize

  18. Automatic differentiation of functions

    International Nuclear Information System (INIS)

    Douglas, S.R.

    1990-06-01

    Automatic differentiation is a method of computing derivatives of functions to any order in any number of variables. The functions must be expressible as combinations of elementary functions. When evaluated at specific numerical points, the derivatives have no truncation error and are automatically found. The method is illustrated by simple examples. Source code in FORTRAN is provided

  19. AUTOMATIC INTRAVENOUS DRIP CONTROLLER*

    African Journals Online (AJOL)

    Both the nursing staff shortage and the need for precise control in the administration of dangerous drugs intra- venously have led to the development of various devices to achieve an automatic system. The continuous automatic control of the drip rate eliminates errors due to any physical effect such as movement of the ...

  20. Automatic Camera Control

    DEFF Research Database (Denmark)

    Burelli, Paolo; Preuss, Mike

    2014-01-01

    Automatically generating computer animations is a challenging and complex problem with applications in games and film production. In this paper, we investigate howto translate a shot list for a virtual scene into a series of virtual camera configurations — i.e automatically controlling the virtual...

  1. Automatic Power Line Inspection Using UAV Images

    Directory of Open Access Journals (Sweden)

    Yong Zhang

    2017-08-01

    Full Text Available Power line inspection ensures the safe operation of a power transmission grid. Using unmanned aerial vehicle (UAV images of power line corridors is an effective way to carry out these vital inspections. In this paper, we propose an automatic inspection method for power lines using UAV images. This method, known as the power line automatic measurement method based on epipolar constraints (PLAMEC, acquires the spatial position of the power lines. Then, the semi patch matching based on epipolar constraints (SPMEC dense matching method is applied to automatically extract dense point clouds within the power line corridor. Obstacles can then be automatically detected by calculating the spatial distance between a power line and the point cloud representing the ground. Experimental results show that the PLAMEC automatically measures power lines effectively with a measurement accuracy consistent with that of manual stereo measurements. The height root mean square (RMS error of the point cloud was 0.233 m, and the RMS error of the power line was 0.205 m. In addition, we verified the detected obstacles in the field and measured the distance between the canopy and power line using a laser range finder. The results show that the difference of these two distances was within ±0.5 m.

  2. Quantifying Transmission.

    Science.gov (United States)

    Woolhouse, Mark

    2017-07-01

    Transmissibility is the defining characteristic of infectious diseases. Quantifying transmission matters for understanding infectious disease epidemiology and designing evidence-based disease control programs. Tracing individual transmission events can be achieved by epidemiological investigation coupled with pathogen typing or genome sequencing. Individual infectiousness can be estimated by measuring pathogen loads, but few studies have directly estimated the ability of infected hosts to transmit to uninfected hosts. Individuals' opportunities to transmit infection are dependent on behavioral and other risk factors relevant given the transmission route of the pathogen concerned. Transmission at the population level can be quantified through knowledge of risk factors in the population or phylogeographic analysis of pathogen sequence data. Mathematical model-based approaches require estimation of the per capita transmission rate and basic reproduction number, obtained by fitting models to case data and/or analysis of pathogen sequence data. Heterogeneities in infectiousness, contact behavior, and susceptibility can have substantial effects on the epidemiology of an infectious disease, so estimates of only mean values may be insufficient. For some pathogens, super-shedders (infected individuals who are highly infectious) and super-spreaders (individuals with more opportunities to transmit infection) may be important. Future work on quantifying transmission should involve integrated analyses of multiple data sources.

  3. Automatic Test Systems Aquisition

    National Research Council Canada - National Science Library

    1994-01-01

    We are providing this final memorandum report for your information and use. This report discusses the efforts to achieve commonality in standards among the Military Departments as part of the DoD policy for automatic test systems (ATS...

  4. Data transmission

    National Research Council Canada - National Science Library

    Tugal, Dogan A; Tugal, Osman

    1989-01-01

    This updated second edition provides working answers to today's critical questions about designing and managing all types of data transmission systems and features a new chapter on local area networks (LANs...

  5. Shingles Transmission

    Science.gov (United States)

    ... Search Form Controls Cancel Submit Search The CDC Shingles (Herpes Zoster) Note: Javascript is disabled or is ... message, please visit this page: About CDC.gov . Shingles Home About Shingles Overview Signs & Symptoms Transmission Complications ...

  6. Automatic requirements traceability

    OpenAIRE

    Andžiulytė, Justė

    2017-01-01

    This paper focuses on automatic requirements traceability and algorithms that automatically find recommendation links for requirements. The main objective of this paper is the evaluation of these algorithms and preparation of the method defining algorithms to be used in different cases. This paper presents and examines probabilistic, vector space and latent semantic indexing models of information retrieval and association rule mining using authors own implementations of these algorithms and o...

  7. Position automatic determination technology

    International Nuclear Information System (INIS)

    1985-10-01

    This book tells of method of position determination and characteristic, control method of position determination and point of design, point of sensor choice for position detector, position determination of digital control system, application of clutch break in high frequency position determination, automation technique of position determination, position determination by electromagnetic clutch and break, air cylinder, cam and solenoid, stop position control of automatic guide vehicle, stacker crane and automatic transfer control.

  8. Automatic text summarization

    CERN Document Server

    Torres Moreno, Juan Manuel

    2014-01-01

    This new textbook examines the motivations and the different algorithms for automatic document summarization (ADS). We performed a recent state of the art. The book shows the main problems of ADS, difficulties and the solutions provided by the community. It presents recent advances in ADS, as well as current applications and trends. The approaches are statistical, linguistic and symbolic. Several exemples are included in order to clarify the theoretical concepts.  The books currently available in the area of Automatic Document Summarization are not recent. Powerful algorithms have been develop

  9. Automatic Ultrasound Scanning

    DEFF Research Database (Denmark)

    Moshavegh, Ramin

    on the scanners, and to improve the computer-aided diagnosis (CAD) in ultrasound by introducing new quantitative measures. Thus, four major issues concerning automation of the medical ultrasound are addressed in this PhD project. They touch upon gain adjustments in ultrasound, automatic synthetic aperture image...... on the user adjustments on the scanner interface to optimize the scan settings. This explains the huge interest in the subject of this PhD project entitled “AUTOMATIC ULTRASOUND SCANNING”. The key goals of the project have been to develop automated techniques to minimize the unnecessary settings...

  10. HIV Transmission

    Science.gov (United States)

    ... Abroad Treatment Basic Statistics Get Tested Find an HIV testing site near you. Enter ZIP code or city Follow HIV/AIDS CDC HIV CDC HIV/AIDS See RSS | ... on HIV Syndicated Content Website Feedback HIV/AIDS HIV Transmission Language: English (US) Español (Spanish) Recommend on ...

  11. Reactor component automatic grapple

    International Nuclear Information System (INIS)

    Greenaway, P.R.

    1982-01-01

    A grapple for handling nuclear reactor components in a medium such as liquid sodium which, upon proper seating and alignment of the grapple with the component as sensed by a mechanical logic integral to the grapple, automatically seizes the component. The mechanical logic system also precludes seizure in the absence of proper seating and alignment. (author)

  12. Automatic Commercial Permit Sets

    Energy Technology Data Exchange (ETDEWEB)

    Grana, Paul [Folsom Labs, Inc., San Francisco, CA (United States)

    2017-12-21

    Final report for Folsom Labs’ Solar Permit Generator project, which has successfully completed, resulting in the development and commercialization of a software toolkit within the cloud-based HelioScope software environment that enables solar engineers to automatically generate and manage draft documents for permit submission.

  13. Automatic Complexity Analysis

    DEFF Research Database (Denmark)

    Rosendahl, Mads

    1989-01-01

    One way to analyse programs is to to derive expressions for their computational behaviour. A time bound function (or worst-case complexity) gives an upper bound for the computation time as a function of the size of input. We describe a system to derive such time bounds automatically using abstrac...

  14. Automatic Voltage Control (AVC) of Danish Transmission System - Concept design

    DEFF Research Database (Denmark)

    Qin, Nan; Abildgaard, Hans; Lund, P.

    2014-01-01

    the buses are monitored where the voltage magnitudes are maintained continually. The loss minimization including switching cost is the objectives of the AVC system. The reactive power reserves as constraints are taken into account to limit the regulation capabilities of generators. The Day ahead and short......, objectives, constraints, algorithms for optimal power flow and some special functions in particular systems, which inspires the concept design of a Danish AVC system to address the future challenges of voltage control. In the concept, the Danish AVC design is based on a centralized control scheme. All...

  15. Design of synchromesh mechanism to optimization manual transmission's electric vehicle

    Science.gov (United States)

    Zainuri, Fuad; Sumarsono, Danardono A.; Adhitya, Muhammad; Siregar, Rolan

    2017-03-01

    Significant research has been attempted on a vehicle that lead to the development of transmission that can reduce energy consumption and improve vehicle efficiency. Consumers also expect safety, convenience, and competitive prices. Automatic transmission (AT), continuously variable transmission (CVT), and dual clutch transmission (DCT) is the latest transmission developed for road vehicle. From literature reviews that have been done that this transmission is less effective on electric cars which use batteries as a power source compared to type manual transmission, this is due to the large power losses when making gear changes. Zeroshift system is the transmission can do shift gears with no time (zero time). It was developed for the automatic manual transmission, and this transmission has been used on racing vehicles to eliminate deceleration when gear shift. Zeroshift transmission still use the clutch to change gear in which electromechanical be used to replace the clutch pedal. Therefore, the transmission is too complex for the transmission of electric vehicles, but its mechanism is considered very suitable to increase the transmission efficiency. From this idea, a new innovation design transmission will be created to electric car. The combination synchromesh with zeroshift mechanism for the manual transmission is a transmission that is ideal for improving the transmission efficiency. Installation synchromesh on zeroshift mechanism is expected to replace the function of the clutch MT, and assisted with the motor torque setting when to change gear. Additionally to consider is the weight of the transmission, ease of manufacturing, ease of installation with an electric motor, as well as ease of use by drivers is a matter that must be done to obtain a new transmission system that is suitable for electric cars.

  16. Automatic dose-rate controlling equipment

    International Nuclear Information System (INIS)

    Szasz, T.; Nagy Czirok, Cs.; Batki, L.; Antal, S.

    1977-01-01

    The patent of a dose-rate controlling equipment that can be attached to X-ray image-amplifiers is presented. In the new equipment the current of the photocatode of the image-amplifier is led into the regulating unit, which controls the X-ray generator automatically. The advantages of the equipment are the following: it can be simply attached to any type of X-ray image-amplifier, it accomplishes fast and sensitive regulation, it makes possible the control of both the mA and the kV values, it is attached to the most reliable point of the image-transmission chain. (L.E.)

  17. Research of pneumatic control transmission system for small irradiation samples

    International Nuclear Information System (INIS)

    Bai Zhongxiong; Zhang Haibing; Rong Ru; Zhang Tao

    2008-01-01

    In order to reduce the absorbed dose damage for the operator, pneumatic control has been adopted to realize the rapid transmission of small irradiation samples. On/off of pneumatic circuit and directions for the rapid transmission system are controlled by the electrical control part. The main program initializes the system and detects the location of the manual/automatic change-over switch, and call for the corresponding subprogram to achieve the automatic or manual operation. Automatic subprogram achieves the automatic sample transmission; Manual subprogram completes the deflation, and back and forth movement of the radiation samples. This paper introduces in detail the implementation of the system, in terms of both hardware and software design. (authors)

  18. Automatic trend estimation

    CERN Document Server

    Vamos¸, C˘alin

    2013-01-01

    Our book introduces a method to evaluate the accuracy of trend estimation algorithms under conditions similar to those encountered in real time series processing. This method is based on Monte Carlo experiments with artificial time series numerically generated by an original algorithm. The second part of the book contains several automatic algorithms for trend estimation and time series partitioning. The source codes of the computer programs implementing these original automatic algorithms are given in the appendix and will be freely available on the web. The book contains clear statement of the conditions and the approximations under which the algorithms work, as well as the proper interpretation of their results. We illustrate the functioning of the analyzed algorithms by processing time series from astrophysics, finance, biophysics, and paleoclimatology. The numerical experiment method extensively used in our book is already in common use in computational and statistical physics.

  19. Automatic Program Development

    DEFF Research Database (Denmark)

    Automatic Program Development is a tribute to Robert Paige (1947-1999), our accomplished and respected colleague, and moreover our good friend, whose untimely passing was a loss to our academic and research community. We have collected the revised, updated versions of the papers published in his ...... a renewed stimulus for continuing and deepening Bob's research visions. A familiar touch is given to the book by some pictures kindly provided to us by his wife Nieba, the personal recollections of his brother Gary and some of his colleagues and friends....... honor in the Higher-Order and Symbolic Computation Journal in the years 2003 and 2005. Among them there are two papers by Bob: (i) a retrospective view of his research lines, and (ii) a proposal for future studies in the area of the automatic program derivation. The book also includes some papers...

  20. Automaticity or active control

    DEFF Research Database (Denmark)

    Tudoran, Ana Alina; Olsen, Svein Ottar

    This study addresses the quasi-moderating role of habit strength in explaining action loyalty. A model of loyalty behaviour is proposed that extends the traditional satisfaction–intention–action loyalty network. Habit strength is conceptualised as a cognitive construct to refer to the psychological...... aspects of the construct, such as routine, inertia, automaticity, or very little conscious deliberation. The data consist of 2962 consumers participating in a large European survey. The results show that habit strength significantly moderates the association between satisfaction and action loyalty, and......, respectively, between intended loyalty and action loyalty. At high levels of habit strength, consumers are more likely to free up cognitive resources and incline the balance from controlled to routine and automatic-like responses....

  1. Automatic food decisions

    DEFF Research Database (Denmark)

    Mueller Loose, Simone

    Consumers' food decisions are to a large extent shaped by automatic processes, which are either internally directed through learned habits and routines or externally influenced by context factors and visual information triggers. Innovative research methods such as eye tracking, choice experiments...... and food diaries allow us to better understand the impact of unconscious processes on consumers' food choices. Simone Mueller Loose will provide an overview of recent research insights into the effects of habit and context on consumers' food choices....

  2. Automatic Language Identification

    Science.gov (United States)

    2000-08-01

    hundreds guish one language from another. The reader is referred of input languages would need to be supported , the cost of to the linguistics literature...eventually obtained bet- 108 TRAINING FRENCH GERMAN ITRAIING FRENCH M- ALGORITHM - __ GERMAN NHSPANISH TRAINING SPEECH SET OF MODELS: UTTERANCES ONE MODEL...i.e. vowels ) for each speech utterance are located malized to be insensitive to overall amplitude, pitch and automatically. Next, feature vectors

  3. Transcending Transmission

    DEFF Research Database (Denmark)

    Schoeneborn, Dennis; Trittin, Hannah

    2013-01-01

    Purpose – Extant research on corporate social responsibility (CSR) communication primarily relies on a transmission model of communication that treats organizations and communication as distinct phenomena. This approach has been criticized for neglecting the formative role of communication...... in the emergence of organizations. This paper seeks to propose to reconceptualize CSR communication by drawing on the “communication constitutes organizations” (CCO) perspective. Design/methodology/approach – This is a conceptual paper that explores the implications of switching from an instrumental...... are stabilized by various non-human entities that “act” on their behalf. Accordingly, CSR communication should also take into account non-human agency and responsibility. Originality/value – This paper links the literature on CSR communication to broader debates in organizational communication studies and...

  4. Automatic Evaluation Of Interferograms

    Science.gov (United States)

    Becker, Friedhelm; Meier, Gerd E. A.; Wegner, Horst

    1983-03-01

    A system for the automatic evaluation of interference patterns has been developed. After digitizing the interferograms from classical and holografic interferometers with a television digitizer and performing different picture enhancement operations the fringe loci are extracted by use of a floating-threshold method. The fringes are numbered using a special scheme after the removal of any fringe disconnections which might appear if there was insufficient contrast in the interferograms. The reconstruction of the object function from the numbered fringe field is achieved by a local polynomial least-squares approximation. Applications are given, demonstrating the evaluation of interferograms of supersonic flow fields and the analysis of holografic interferograms of car-tyres.

  5. Automatic quantitative renal scintigraphy

    International Nuclear Information System (INIS)

    Valeyre, J.; Deltour, G.; Delisle, M.J.; Bouchard, A.

    1976-01-01

    Renal scintigraphy data may be analyzed automatically by the use of a processing system coupled to an Anger camera (TRIDAC-MULTI 8 or CINE 200). The computing sequence is as follows: normalization of the images; background noise subtraction on both images; evaluation of mercury 197 uptake by the liver and spleen; calculation of the activity fractions on each kidney with respect to the injected dose, taking into account the kidney depth and the results referred to normal values; edition of the results. Automation minimizes the scattering parameters and by its simplification is a great asset in routine work [fr

  6. Automatic readout micrometer

    Science.gov (United States)

    Lauritzen, T.

    A measuring system is described for surveying and very accurately positioning objects with respect to a reference line. A principle use of this surveying system is for accurately aligning the electromagnets which direct a particle beam emitted from a particle accelerator. Prior art surveying systems require highly skilled surveyors. Prior art systems include, for example, optical surveying systems which are susceptible to operator reading errors, and celestial navigation-type surveying systems, with their inherent complexities. The present invention provides an automatic readout micrometer which can very accurately measure distances. The invention has a simplicity of operation which practically eliminates the possibilities of operator optical reading error, owning to the elimination of traditional optical alignments for making measurements. The invention has an extendable arm which carries a laser surveying target. The extendable arm can be continuously positioned over its entire length of travel by either a coarse of fine adjustment without having the fine adjustment outrun the coarse adjustment until a reference laser beam is centered on the target as indicated by a digital readout. The length of the micrometer can then be accurately and automatically read by a computer and compared with a standardized set of alignment measurements. Due to its construction, the micrometer eliminates any errors due to temperature changes when the system is operated within a standard operating temperature range.

  7. Automatic personnel contamination monitor

    International Nuclear Information System (INIS)

    Lattin, Kenneth R.

    1978-01-01

    United Nuclear Industries, Inc. (UNI) has developed an automatic personnel contamination monitor (APCM), which uniquely combines the design features of both portal and hand and shoe monitors. In addition, this prototype system also has a number of new features, including: micro computer control and readout, nineteen large area gas flow detectors, real-time background compensation, self-checking for system failures, and card reader identification and control. UNI's experience in operating the Hanford N Reactor, located in Richland, Washington, has shown the necessity of automatically monitoring plant personnel for contamination after they have passed through the procedurally controlled radiation zones. This final check ensures that each radiation zone worker has been properly checked before leaving company controlled boundaries. Investigation of the commercially available portal and hand and shoe monitors indicated that they did not have the sensitivity or sophistication required for UNI's application, therefore, a development program was initiated, resulting in the subject monitor. Field testing shows good sensitivity to personnel contamination with the majority of alarms showing contaminants on clothing, face and head areas. In general, the APCM has sensitivity comparable to portal survey instrumentation. The inherit stand-in, walk-on feature of the APCM not only makes it easy to use, but makes it difficult to bypass. (author)

  8. Reachability Games on Automatic Graphs

    Science.gov (United States)

    Neider, Daniel

    In this work we study two-person reachability games on finite and infinite automatic graphs. For the finite case we empirically show that automatic game encodings are competitive to well-known symbolic techniques such as BDDs, SAT and QBF formulas. For the infinite case we present a novel algorithm utilizing algorithmic learning techniques, which allows to solve huge classes of automatic reachability games.

  9. Automatic reactor protection system tester

    International Nuclear Information System (INIS)

    Deliant, J.D.; Jahnke, S.; Raimondo, E.

    1988-01-01

    The object of this paper is to present the automatic tester of reactor protection systems designed and developed by EDF and Framatome. In order, the following points are discussed: . The necessity for reactor protection system testing, . The drawbacks of manual testing, . The description and use of the Framatome automatic tester, . On-site installation of this system, . The positive results obtained using the Framatome automatic tester in France

  10. Automatic sets and Delone sets

    International Nuclear Information System (INIS)

    Barbe, A; Haeseler, F von

    2004-01-01

    Automatic sets D part of Z m are characterized by having a finite number of decimations. They are equivalently generated by fixed points of certain substitution systems, or by certain finite automata. As examples, two-dimensional versions of the Thue-Morse, Baum-Sweet, Rudin-Shapiro and paperfolding sequences are presented. We give a necessary and sufficient condition for an automatic set D part of Z m to be a Delone set in R m . The result is then extended to automatic sets that are defined as fixed points of certain substitutions. The morphology of automatic sets is discussed by means of examples

  11. 4th International Conference on Power Transmissions

    CERN Document Server

    2013-01-01

    This books contains the Proceedings of the 4th International Conference on Power Transmissions, that was held in Sinaia, Romania from June 20 -23, 2012. Power Transmissions is a very complex and multi-disciplinary scientific field of Mechanical Engineering that covers the different types of transmissions (mechanical, hydraulic, pneumatic) as well as all the machine elements involved, such as gears, bearings, shafts, couplings and a lot more. It concerns not only their basic theory but also their design, analysis, testing, application and maintenance. The requirements set to modern power transmissions are really tough to meet: They need to be more efficient, stronger, smaller, noiseless, easier to produce and to cost less. There is a strong demand to become easier in operation and maintenance, or even automatic and in maintenance-free. Last but not least, they should be easily recycled and respect the environment. Joint efforts of specialists from both academia and industry can significantly contribute to fulf...

  12. Automatic quantitative metallography

    International Nuclear Information System (INIS)

    Barcelos, E.J.B.V.; Ambrozio Filho, F.; Cunha, R.C.

    1976-01-01

    The quantitative determination of metallographic parameters is analysed through the description of Micro-Videomat automatic image analysis system and volumetric percentage of perlite in nodular cast irons, porosity and average grain size in high-density sintered pellets of UO 2 , and grain size of ferritic steel. Techniques adopted are described and results obtained are compared with the corresponding ones by the direct counting process: counting of systematic points (grid) to measure volume and intersections method, by utilizing a circunference of known radius for the average grain size. The adopted technique for nodular cast iron resulted from the small difference of optical reflectivity of graphite and perlite. Porosity evaluation of sintered UO 2 pellets is also analyzed [pt

  13. Semi-automatic fluoroscope

    International Nuclear Information System (INIS)

    Tarpley, M.W.

    1976-10-01

    Extruded aluminum-clad uranium-aluminum alloy fuel tubes must pass many quality control tests before irradiation in Savannah River Plant nuclear reactors. Nondestructive test equipment has been built to automatically detect high and low density areas in the fuel tubes using x-ray absorption techniques with a video analysis system. The equipment detects areas as small as 0.060-in. dia with 2 percent penetrameter sensitivity. These areas are graded as to size and density by an operator using electronic gages. Video image enhancement techniques permit inspection of ribbed cylindrical tubes and make possible the testing of areas under the ribs. Operation of the testing machine, the special low light level television camera, and analysis and enhancement techniques are discussed

  14. AUTOMATIC ARCHITECTURAL STYLE RECOGNITION

    Directory of Open Access Journals (Sweden)

    M. Mathias

    2012-09-01

    Full Text Available Procedural modeling has proven to be a very valuable tool in the field of architecture. In the last few years, research has soared to automatically create procedural models from images. However, current algorithms for this process of inverse procedural modeling rely on the assumption that the building style is known. So far, the determination of the building style has remained a manual task. In this paper, we propose an algorithm which automates this process through classification of architectural styles from facade images. Our classifier first identifies the images containing buildings, then separates individual facades within an image and determines the building style. This information could then be used to initialize the building reconstruction process. We have trained our classifier to distinguish between several distinct architectural styles, namely Flemish Renaissance, Haussmannian and Neoclassical. Finally, we demonstrate our approach on various street-side images.

  15. Automatic surveying techniques

    International Nuclear Information System (INIS)

    Sah, R.

    1976-01-01

    In order to investigate the feasibility of automatic surveying methods in a more systematic manner, the PEP organization signed a contract in late 1975 for TRW Systems Group to undertake a feasibility study. The completion of this study resulted in TRW Report 6452.10-75-101, dated December 29, 1975, which was largely devoted to an analysis of a survey system based on an Inertial Navigation System. This PEP note is a review and, in some instances, an extension of that TRW report. A second survey system which employed an ''Image Processing System'' was also considered by TRW, and it will be reviewed in the last section of this note. 5 refs., 5 figs., 3 tabs

  16. Automatic alkaloid removal system.

    Science.gov (United States)

    Yahaya, Muhammad Rizuwan; Hj Razali, Mohd Hudzari; Abu Bakar, Che Abdullah; Ismail, Wan Ishak Wan; Muda, Wan Musa Wan; Mat, Nashriyah; Zakaria, Abd

    2014-01-01

    This alkaloid automated removal machine was developed at Instrumentation Laboratory, Universiti Sultan Zainal Abidin Malaysia that purposely for removing the alkaloid toxicity from Dioscorea hispida (DH) tuber. It is a poisonous plant where scientific study has shown that its tubers contain toxic alkaloid constituents, dioscorine. The tubers can only be consumed after it poisonous is removed. In this experiment, the tubers are needed to blend as powder form before inserting into machine basket. The user is need to push the START button on machine controller for switching the water pump ON by then creating turbulence wave of water in machine tank. The water will stop automatically by triggering the outlet solenoid valve. The powders of tubers are washed for 10 minutes while 1 liter of contaminated water due toxin mixture is flowing out. At this time, the controller will automatically triggered inlet solenoid valve and the new water will flow in machine tank until achieve the desire level that which determined by ultra sonic sensor. This process will repeated for 7 h and the positive result is achieved and shows it significant according to the several parameters of biological character ofpH, temperature, dissolve oxygen, turbidity, conductivity and fish survival rate or time. From that parameter, it also shows the positive result which is near or same with control water and assuming was made that the toxin is fully removed when the pH of DH powder is near with control water. For control water, the pH is about 5.3 while water from this experiment process is 6.0 and before run the machine the pH of contaminated water is about 3.8 which are too acid. This automated machine can save time for removing toxicity from DH compared with a traditional method while less observation of the user.

  17. Classifying visemes for automatic lipreading

    NARCIS (Netherlands)

    Visser, Michiel; Poel, Mannes; Nijholt, Antinus; Matousek, Vaclav; Mautner, Pavel; Ocelikovi, Jana; Sojka, Petr

    1999-01-01

    Automatic lipreading is automatic speech recognition that uses only visual information. The relevant data in a video signal is isolated and features are extracted from it. From a sequence of feature vectors, where every vector represents one video image, a sequence of higher level semantic elements

  18. Survey of Transmission Cost Allocation Methodologies for Regional Transmission Organizations

    Energy Technology Data Exchange (ETDEWEB)

    Fink, S.; Porter, K.; Mudd, C.; Rogers, J.

    2011-02-01

    The report presents transmission cost allocation methodologies for reliability transmission projects, generation interconnection, and economic transmission projects for all Regional Transmission Organizations.

  19. Automatic exposure for xeromammography

    International Nuclear Information System (INIS)

    Aichinger, H.

    1977-01-01

    During mammography without intensifying screens, exposure measurements are carried out behind the film. It is, however, difficult to construct an absolutely shadow-free ionization chamber of adequate sensitivity working in the necessary range of 25 to 50 kV. Repeated attempts have been made to utilize the advantages of automatic exposure for xero-mammography. In this case also the ionization chamber was placed behind the Xerox plate. Depending on tube filtration, object thickness and tube voltage, more than 80%, sometimes even 90%, of the radiation is absorbed by the Xerox plate. Particularly the characteristic Mo radiation of 17.4 keV and 19.6 keV is almost totally absorbed by the plate and cannot therefore be registered by the ionization chamber. This results in a considerable dependence of the exposure on kV and object thickness. Dependence on tube voltage and object thickness have been examined dosimetrically and spectroscopically with a Ge(Li)-spectrometer. Finally, the successful use of a shadow-free chamber is described; this has been particularly adapted for xero-mammography and is placed in front of the plate. (orig) [de

  20. Historical Review and Perspective on Automatic Journalizing

    OpenAIRE

    Kato, Masaki

    2017-01-01

    ContentsIntroduction1. EDP Accounting and Automatic Journalizing2. Learning System of Automatic Journalizing3. Automatic Journalizing by the Artificial Intelligence4. Direction of the Progress of the Accounting Information System

  1. Research on Application of Automatic Weather Station Based on Internet of Things

    Science.gov (United States)

    Jianyun, Chen; Yunfan, Sun; Chunyan, Lin

    2017-12-01

    In this paper, the Internet of Things is briefly introduced, and then its application in the weather station is studied. A method of data acquisition and transmission based on NB-iot communication mode is proposed, Introduction of Internet of things technology, Sensor digital and independent power supply as the technical basis, In the construction of Automatic To realize the intelligent interconnection of the automatic weather station, and then to form an automatic weather station based on the Internet of things. A network structure of automatic weather station based on Internet of things technology is constructed to realize the independent operation of intelligent sensors and wireless data transmission. Research on networking data collection and dissemination of meteorological data, through the data platform for data analysis, the preliminary work of meteorological information publishing standards, networking of meteorological information receiving terminal provides the data interface, to the wisdom of the city, the wisdom of the purpose of the meteorological service.

  2. Electronic amplifiers for automatic compensators

    CERN Document Server

    Polonnikov, D Ye

    1965-01-01

    Electronic Amplifiers for Automatic Compensators presents the design and operation of electronic amplifiers for use in automatic control and measuring systems. This book is composed of eight chapters that consider the problems of constructing input and output circuits of amplifiers, suppression of interference and ensuring high sensitivity.This work begins with a survey of the operating principles of electronic amplifiers in automatic compensator systems. The succeeding chapters deal with circuit selection and the calculation and determination of the principal characteristics of amplifiers, as

  3. Automatic analysis of multiparty meetings

    Indian Academy of Sciences (India)

    AMI) meeting corpus, the development of a meeting speech recognition system, and systems for the automatic segmentation, summarization and social processing of meetings, together with some example applications based on these systems.

  4. AVID: Automatic Visualization Interface Designer

    National Research Council Canada - National Science Library

    Chuah, Mei

    2000-01-01

    .... Automatic generation offers great flexibility in performing data and information analysis tasks, because new designs are generated on a case by case basis to suit current and changing future needs...

  5. Clothes Dryer Automatic Termination Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    TeGrotenhuis, Ward E.

    2014-10-01

    Volume 2: Improved Sensor and Control Designs Many residential clothes dryers on the market today provide automatic cycles that are intended to stop when the clothes are dry, as determined by the final remaining moisture content (RMC). However, testing of automatic termination cycles has shown that many dryers are susceptible to over-drying of loads, leading to excess energy consumption. In particular, tests performed using the DOE Test Procedure in Appendix D2 of 10 CFR 430 subpart B have shown that as much as 62% of the energy used in a cycle may be from over-drying. Volume 1 of this report shows an average of 20% excess energy from over-drying when running automatic cycles with various load compositions and dryer settings. Consequently, improving automatic termination sensors and algorithms has the potential for substantial energy savings in the U.S.

  6. An automatic image recognition approach

    Directory of Open Access Journals (Sweden)

    Tudor Barbu

    2007-07-01

    Full Text Available Our paper focuses on the graphical analysis domain. We propose an automatic image recognition technique. This approach consists of two main pattern recognition steps. First, it performs an image feature extraction operation on an input image set, using statistical dispersion features. Then, an unsupervised classification process is performed on the previously obtained graphical feature vectors. An automatic region-growing based clustering procedure is proposed and utilized in the classification stage.

  7. Automatic sample changers maintenance manual

    International Nuclear Information System (INIS)

    Myers, T.A.

    1978-10-01

    This manual describes and provides trouble-shooting aids for the Automatic Sample Changer electronics on the automatic beta counting system, developed by the Los Alamos Scientific Laboratory Group CNC-11. The output of a gas detector is shaped by a preamplifier, then is coupled to an amplifier. Amplifier output is discriminated and is the input to a scaler. An identification number is associated with each sample. At a predetermined count length, the identification number, scaler data plus other information is punched out on a data card. The next sample to be counted is automatically selected. The beta counter uses the same electronics as the prior count did, the only difference being the sample identification number and sample itself. This manual is intended as a step-by-step aid in trouble-shooting the electronics associated with positioning the sample, counting the sample, and getting the needed data punched on an 80-column data card

  8. Development of an automatic scaler

    International Nuclear Information System (INIS)

    He Yuehong

    2009-04-01

    A self-designed automatic scaler is introduced. A microcontroller LPC936 is used as the master chip in the scaler. A counter integrated with the micro-controller is configured to operate as external pulse counter. Software employed in the scaler is based on a embedded real-time operating system kernel named Small RTOS. Data storage, calculation and some other functions are also provided. The scaler is designed for applications with low cost, low power consumption solutions. By now, the automatic scaler has been applied in a surface contamination instrument. (authors)

  9. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming focuses on the techniques of automatic programming used with digital computers. Topics covered range from the design of machine-independent programming languages to the use of recursive procedures in ALGOL 60. A multi-pass translation scheme for ALGOL 60 is described, along with some commercial source languages. The structure and use of the syntax-directed compiler is also considered.Comprised of 12 chapters, this volume begins with a discussion on the basic ideas involved in the description of a computing process as a program for a computer, expressed in

  10. Traduction automatique et terminologie automatique (Automatic Translation and Automatic Terminology

    Science.gov (United States)

    Dansereau, Jules

    1978-01-01

    An exposition of reasons why a system of automatic translation could not use a terminology bank except as a source of information. The fundamental difference between the two tools is explained and examples of translation and mistranslation are given as evidence of the limits and possibilities of each process. (Text is in French.) (AMH)

  11. Design of electric control system for automatic vegetable bundling machine

    Science.gov (United States)

    Bao, Yan

    2017-06-01

    A design can meet the requirements of automatic bale food structure and has the advantages of simple circuit, and the volume is easy to enhance the electric control system of machine carrying bunch of dishes and low cost. The bundle of vegetable machine should meet the sensor to detect and control, in order to meet the control requirements; binding force can be adjusted by the button to achieve; strapping speed also can be adjusted, by the keys to set; sensors and mechanical line connection, convenient operation; can be directly connected with the plug, the 220V power supply can be connected to a power source; if, can work, by the transmission signal sensor, MCU to control the motor, drive and control procedures for small motor. The working principle of LED control circuit and temperature control circuit is described. The design of electric control system of automatic dish machine.

  12. Automatically Preparing Safe SQL Queries

    Science.gov (United States)

    Bisht, Prithvi; Sistla, A. Prasad; Venkatakrishnan, V. N.

    We present the first sound program source transformation approach for automatically transforming the code of a legacy web application to employ PREPARE statements in place of unsafe SQL queries. Our approach therefore opens the way for eradicating the SQL injection threat vector from legacy web applications.

  13. Automatic Validation of Protocol Narration

    DEFF Research Database (Denmark)

    Bodei, Chiara; Buchholtz, Mikael; Degano, Pierpablo

    2003-01-01

    We perform a systematic expansion of protocol narrations into terms of a process algebra in order to make precise some of the detailed checks that need to be made in a protocol. We then apply static analysis technology to develop an automatic validation procedure for protocols. Finally, we...

  14. The Automatic Measurement of Targets

    DEFF Research Database (Denmark)

    Höhle, Joachim

    1997-01-01

    The automatic measurement of targets is demonstrated by means of a theoretical example and by an interactive measuring program for real imagery from a réseau camera. The used strategy is a combination of two methods: the maximum correlation coefficient and the correlation in the subpixel range...... interactive software is also part of a computer-assisted learning program on digital photogrammetry....

  15. Automatic Error Analysis Using Intervals

    Science.gov (United States)

    Rothwell, E. J.; Cloud, M. J.

    2012-01-01

    A technique for automatic error analysis using interval mathematics is introduced. A comparison to standard error propagation methods shows that in cases involving complicated formulas, the interval approach gives comparable error estimates with much less effort. Several examples are considered, and numerical errors are computed using the INTLAB…

  16. The automotive transmission book

    CERN Document Server

    Fischer, Robert; Jürgens, Gunter; Najork, Rolf; Pollak, Burkhard

    2015-01-01

    This book presents essential information on systems and interactions in automotive transmission technology and outlines the methodologies used to analyze and develop transmission concepts and designs. Functions of and interactions between components and subassemblies of transmissions are introduced, providing a basis for designing transmission systems and for determining their potentials and properties in vehicle-specific applications: passenger cars, trucks, buses, tractors, and motorcycles. With these fundamentals the presentation provides universal resources for both state-of-the-art and future transmission technologies, including systems for electric and hybrid electric vehicles.

  17. Automatic data acquisition system of environmental radiation monitor with a personal computer

    International Nuclear Information System (INIS)

    Ohkubo, Tohru; Nakamura, Takashi.

    1984-05-01

    The automatic data acquisition system of environmental radiation monitor was developed in a low price by using a PET personal computer. The count pulses from eight monitors settled at four site boundaries were transmitted to a radiation control room by a signal transmission device and analyzed by the computer via 12 channel scaler and PET-CAMAC Interface for graphic display and printing. (author)

  18. Human and automatic speaker recognition over telecommunication channels

    CERN Document Server

    Fernández Gallardo, Laura

    2016-01-01

    This work addresses the evaluation of the human and the automatic speaker recognition performances under different channel distortions caused by bandwidth limitation, codecs, and electro-acoustic user interfaces, among other impairments. Its main contribution is the demonstration of the benefits of communication channels of extended bandwidth, together with an insight into how speaker-specific characteristics of speech are preserved through different transmissions. It provides sufficient motivation for considering speaker recognition as a criterion for the migration from narrowband to enhanced bandwidths, such as wideband and super-wideband.

  19. Studies and Proposals for an Automatic Crystal Control System

    CERN Document Server

    Drobychev, Gleb; Khruschinsky, A A; Korzhik, Mikhail; Missevitch, Oleg; Oriboni, André; Peigneux, Jean-Pierre; Schneegans, Marc

    1997-01-01

    This document presents the status of the studies for an Automatic Crystal Control System ( ACCOS) performed since autumn 1995 for the CMS collaboration. Evaluation of a startstop method for light yield, light uniformity and decay time measurements of PbWO4 crystals is presented, as well as the first results obtained with a compact double-beam spectrophotometer for transverse transmission. Various overall schemes are proposed for an integrated set-up including crystal dimension measurement. The initial financial evaluationperformed is also given.

  20. Automatisms: bridging clinical neurology with criminal law.

    Science.gov (United States)

    Rolnick, Joshua; Parvizi, Josef

    2011-03-01

    The law, like neurology, grapples with the relationship between disease states and behavior. Sometimes, the two disciplines share the same terminology, such as automatism. In law, the "automatism defense" is a claim that action was involuntary or performed while unconscious. Someone charged with a serious crime can acknowledge committing the act and yet may go free if, relying on the expert testimony of clinicians, the court determines that the act of crime was committed in a state of automatism. In this review, we explore the relationship between the use of automatism in the legal and clinical literature. We close by addressing several issues raised by the automatism defense: semantic ambiguity surrounding the term automatism, the presence or absence of consciousness during automatisms, and the methodological obstacles that have hindered the study of cognition during automatisms. Copyright © 2010 Elsevier Inc. All rights reserved.

  1. Reflection-transmission photoellipsometry: theory and experiments.

    Science.gov (United States)

    Bader, G; Ashrit, P V; Girouard, F E; Truong, V V

    1995-04-01

    We propose a method that uses reflection and transmission photoellipsometry to analyze samples consisting of thin films combined with semitransparent thick layers or substrates in the form of multilayer structures. Athick film or substrate is defined as a layer for which no interference effects can be observed for a given wavelength resolution, and contributions from multiple reflections in the substrate are taken into account in the theoretical treatment. An automatic reflection-transmission spectroscopic ellipsometer was built to test the theory, and satisfactory results have been obtained. Examples corresponding to a strongly absorbing film deposited on a glass substrate and a highly transmitting film also deposited on glass are shown. In both cases a good fit between theory and experiment is found. The photoellipsometric method presented is particularly suited to the analysis of actual samples of energy-efficient coatings for windows.

  2. Self-Compassion and Automatic Thoughts

    Science.gov (United States)

    Akin, Ahmet

    2012-01-01

    The aim of this research is to examine the relationships between self-compassion and automatic thoughts. Participants were 299 university students. In this study, the Self-compassion Scale and the Automatic Thoughts Questionnaire were used. The relationships between self-compassion and automatic thoughts were examined using correlation analysis…

  3. Automatic schema evolution in Root

    International Nuclear Information System (INIS)

    Brun, R.; Rademakers, F.

    2001-01-01

    ROOT version 3 (spring 2001) supports automatic class schema evolution. In addition this version also produces files that are self-describing. This is achieved by storing in each file a record with the description of all the persistent classes in the file. Being self-describing guarantees that a file can always be read later, its structure browsed and objects inspected, also when the library with the compiled code of these classes is missing. The schema evolution mechanism supports the frequent case when multiple data sets generated with many different class versions must be analyzed in the same session. ROOT supports the automatic generation of C++ code describing the data objects in a file

  4. Automatic design of magazine covers

    Science.gov (United States)

    Jahanian, Ali; Liu, Jerry; Tretter, Daniel R.; Lin, Qian; Damera-Venkata, Niranjan; O'Brien-Strain, Eamonn; Lee, Seungyon; Fan, Jian; Allebach, Jan P.

    2012-03-01

    In this paper, we propose a system for automatic design of magazine covers that quantifies a number of concepts from art and aesthetics. Our solution to automatic design of this type of media has been shaped by input from professional designers, magazine art directors and editorial boards, and journalists. Consequently, a number of principles in design and rules in designing magazine covers are delineated. Several techniques are derived and employed in order to quantify and implement these principles and rules in the format of a software framework. At this stage, our framework divides the task of design into three main modules: layout of magazine cover elements, choice of color for masthead and cover lines, and typography of cover lines. Feedback from professional designers on our designs suggests that our results are congruent with their intuition.

  5. Automatic computation of radioimmunoassay data

    International Nuclear Information System (INIS)

    Toyota, Takayoshi; Kudo, Mikihiko; Abe, Kanji; Kawamata, Fumiaki; Uehata, Shigeru.

    1975-01-01

    Radioimmunoassay provided dose response curves which showed linearity by the use of logistic transformation (Rodbard). This transformation which was applicable to radioimmunoassay should be useful for the computer processing of insulin and C-peptide assay. In the present studies, standard curves were analysed by testing the fit of analytic functions to radioimmunoassay of insulin and C-peptides. A program for use in combination with the double antibody technique was made by Dr. Kawamata. This approach was evidenced to be useful in order to allow automatic computation of data derived from the double antibody assays of insulin and C-peptides. Automatic corrected calculations of radioimmunoassay data of insulin was found to be satisfactory. (auth.)

  6. MOS voltage automatic tuning circuit

    OpenAIRE

    李, 田茂; 中田, 辰則; 松本, 寛樹

    2004-01-01

    Abstract ###Automatic tuning circuit adjusts frequency performance to compensate for the process variation. Phase locked ###loop (PLL) is a suitable oscillator for the integrated circuit. It is a feedback system that compares the input ###phase with the output phase. It can make the output frequency equal to the input frequency. In this paper, PLL ###fomed of MOSFET's is presented.The presented circuit consists of XOR circuit, Low-pass filter and Relaxation ###Oscillator. On PSPICE simulation...

  7. Automatic Detection of Fake News

    OpenAIRE

    Pérez-Rosas, Verónica; Kleinberg, Bennett; Lefevre, Alexandra; Mihalcea, Rada

    2017-01-01

    The proliferation of misleading information in everyday access media outlets such as social media feeds, news blogs, and online newspapers have made it challenging to identify trustworthy news sources, thus increasing the need for computational tools able to provide insights into the reliability of online content. In this paper, we focus on the automatic identification of fake content in online news. Our contribution is twofold. First, we introduce two novel datasets for the task of fake news...

  8. Automatic controller at associated memory

    International Nuclear Information System (INIS)

    Courty, P.

    1977-06-01

    Organized around an A2 type controller, this CAMAC device allows on command of the associated computer to start reading 64K 16 bit words into an outer memory. This memory is fully controlled by the computer. In the automatic mode, which works at 10 6 words/sec, the computer can access any other module of the same crate by cycle-stealing [fr

  9. Automatic Guidance for Remote Manipulator

    Science.gov (United States)

    Johnston, A. R.

    1986-01-01

    Position sensor and mirror guides manipulator toward object. Grasping becomes automatic when sensor begins to receive signal from reflector on object to be manipulated. Light-emitting diodes on manipulator produce light signals for reflector, which is composite of plane and corner reflectors. Proposed scheme especially useful when manipulator arm tends to flex or when object is moving. Sensor and microprocessor designed to compensate for manipulatorarm oscillation.

  10. Annual review in automatic programming

    CERN Document Server

    Halpern, Mark I; Bolliet, Louis

    2014-01-01

    Computer Science and Technology and their Application is an eight-chapter book that first presents a tutorial on database organization. Subsequent chapters describe the general concepts of Simula 67 programming language; incremental compilation and conversational interpretation; dynamic syntax; the ALGOL 68. Other chapters discuss the general purpose conversational system for graphical programming and automatic theorem proving based on resolution. A survey of extensible programming language is also shown.

  11. Automatically-Programed Machine Tools

    Science.gov (United States)

    Purves, L.; Clerman, N.

    1985-01-01

    Software produces cutter location files for numerically-controlled machine tools. APT, acronym for Automatically Programed Tools, is among most widely used software systems for computerized machine tools. APT developed for explicit purpose of providing effective software system for programing NC machine tools. APT system includes specification of APT programing language and language processor, which executes APT statements and generates NC machine-tool motions specified by APT statements.

  12. Automatic computation of transfer functions

    Science.gov (United States)

    Atcitty, Stanley; Watson, Luke Dale

    2015-04-14

    Technologies pertaining to the automatic computation of transfer functions for a physical system are described herein. The physical system is one of an electrical system, a mechanical system, an electromechanical system, an electrochemical system, or an electromagnetic system. A netlist in the form of a matrix comprises data that is indicative of elements in the physical system, values for the elements in the physical system, and structure of the physical system. Transfer functions for the physical system are computed based upon the netlist.

  13. Automatic segmentation of clinical texts.

    Science.gov (United States)

    Apostolova, Emilia; Channin, David S; Demner-Fushman, Dina; Furst, Jacob; Lytinen, Steven; Raicu, Daniela

    2009-01-01

    Clinical narratives, such as radiology and pathology reports, are commonly available in electronic form. However, they are also commonly entered and stored as free text. Knowledge of the structure of clinical narratives is necessary for enhancing the productivity of healthcare departments and facilitating research. This study attempts to automatically segment medical reports into semantic sections. Our goal is to develop a robust and scalable medical report segmentation system requiring minimum user input for efficient retrieval and extraction of information from free-text clinical narratives. Hand-crafted rules were used to automatically identify a high-confidence training set. This automatically created training dataset was later used to develop metrics and an algorithm that determines the semantic structure of the medical reports. A word-vector cosine similarity metric combined with several heuristics was used to classify each report sentence into one of several pre-defined semantic sections. This baseline algorithm achieved 79% accuracy. A Support Vector Machine (SVM) classifier trained on additional formatting and contextual features was able to achieve 90% accuracy. Plans for future work include developing a configurable system that could accommodate various medical report formatting and content standards.

  14. Drivers of Tuberculosis Transmission.

    Science.gov (United States)

    Mathema, Barun; Andrews, Jason R; Cohen, Ted; Borgdorff, Martien W; Behr, Marcel; Glynn, Judith R; Rustomjee, Roxana; Silk, Benjamin J; Wood, Robin

    2017-11-03

    Measuring tuberculosis transmission is exceedingly difficult, given the remarkable variability in the timing of clinical disease after Mycobacterium tuberculosis infection; incident disease can result from either a recent (ie, weeks to months) or a remote (ie, several years to decades) infection event. Although we cannot identify with certainty the timing and location of tuberculosis transmission for individuals, approaches for estimating the individual probability of recent transmission and for estimating the fraction of tuberculosis cases due to recent transmission in populations have been developed. Data used to estimate the probable burden of recent transmission include tuberculosis case notifications in young children and trends in tuberculin skin test and interferon γ-release assays. More recently, M. tuberculosis whole-genome sequencing has been used to estimate population levels of recent transmission, identify the distribution of specific strains within communities, and decipher chains of transmission among culture-positive tuberculosis cases. The factors that drive the transmission of tuberculosis in communities depend on the burden of prevalent tuberculosis; the ways in which individuals live, work, and interact (eg, congregate settings); and the capacity of healthcare and public health systems to identify and effectively treat individuals with infectious forms of tuberculosis. Here we provide an overview of these factors, describe tools for measurement of ongoing transmission, and highlight knowledge gaps that must be addressed. © The Author 2017. Published by Oxford University Press for the Infectious Diseases Society of America.

  15. Automatic generation of pictorial transcripts of video programs

    Science.gov (United States)

    Shahraray, Behzad; Gibbon, David C.

    1995-03-01

    An automatic authoring system for the generation of pictorial transcripts of video programs which are accompanied by closed caption information is presented. A number of key frames, each of which represents the visual information in a segment of the video (i.e., a scene), are selected automatically by performing a content-based sampling of the video program. The textual information is recovered from the closed caption signal and is initially segmented based on its implied temporal relationship with the video segments. The text segmentation boundaries are then adjusted, based on lexical analysis and/or caption control information, to account for synchronization errors due to possible delays in the detection of scene boundaries or the transmission of the caption information. The closed caption text is further refined through linguistic processing for conversion to lower- case with correct capitalization. The key frames and the related text generate a compact multimedia presentation of the contents of the video program which lends itself to efficient storage and transmission. This compact representation can be viewed on a computer screen, or used to generate the input to a commercial text processing package to generate a printed version of the program.

  16. Research and Application of an Automatic Clam Collecting Device

    Directory of Open Access Journals (Sweden)

    Wang Bin

    2017-01-01

    Full Text Available To collect clams automatically and effectively on coastal beach, an automatic clam collecting device was designed. The device consists of a connecting device, a shovelling device, a conveying device, and a filtering device. The mechanical device is designed based on some of the presented devices, such as a blade with slope, a pipelined conveyor belt, planar linkage mechanisms and a ski mechanism. The connecting device is connected to the device body by bolts. The shovelling device adopts a blade with slope, which can reduce the resistance between sandy soil and the device. The transmission device adopts a conveyor belt with a two-stage reducer, which can effectively control the speed of the transmission and avoid the splash of mud. A mesh structure is used for soil filtering, which is designed with a certain slope, thus sandy soil and other impurities fall from the mesh for its own weight. The designed device for clam collecting will improve efficiency and decrease cost effectively.

  17. Cultural Transmission of Civicness

    DEFF Research Database (Denmark)

    Ljunge, Jan Martin

    2012-01-01

    This paper estimates the intergeneration transmission of civicness by studying second generation immigrants in 29 European countries with ancestry in 83 nations. There is significant transmission of civicness both on the mother’s and the father’s side. The estimates are quantitatively significant...

  18. Cultural Transmission of Civicness

    DEFF Research Database (Denmark)

    Ljunge, Jan Martin

    This paper estimates the intergeneration transmission of civicness by studying second generation immigrants in 29 European countries with ancestry in 83 nations. There is significant transmission of civicness both on the mother’s and the father’s side. The estimates are quantitatively significant...

  19. Unification of automatic target tracking and automatic target recognition

    Science.gov (United States)

    Schachter, Bruce J.

    2014-06-01

    The subject being addressed is how an automatic target tracker (ATT) and an automatic target recognizer (ATR) can be fused together so tightly and so well that their distinctiveness becomes lost in the merger. This has historically not been the case outside of biology and a few academic papers. The biological model of ATT∪ATR arises from dynamic patterns of activity distributed across many neural circuits and structures (including retina). The information that the brain receives from the eyes is "old news" at the time that it receives it. The eyes and brain forecast a tracked object's future position, rather than relying on received retinal position. Anticipation of the next moment - building up a consistent perception - is accomplished under difficult conditions: motion (eyes, head, body, scene background, target) and processing limitations (neural noise, delays, eye jitter, distractions). Not only does the human vision system surmount these problems, but it has innate mechanisms to exploit motion in support of target detection and classification. Biological vision doesn't normally operate on snapshots. Feature extraction, detection and recognition are spatiotemporal. When vision is viewed as a spatiotemporal process, target detection, recognition, tracking, event detection and activity recognition, do not seem as distinct as they are in current ATT and ATR designs. They appear as similar mechanism taking place at varying time scales. A framework is provided for unifying ATT and ATR.

  20. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming, Volume 4 is a collection of papers that deals with the GIER ALGOL compiler, a parameterized compiler based on mechanical linguistics, and the JOVIAL language. A couple of papers describes a commercial use of stacks, an IBM system, and what an ideal computer program support system should be. One paper reviews the system of compilation, the development of a more advanced language, programming techniques, machine independence, and program transfer to other machines. Another paper describes the ALGOL 60 system for the GIER machine including running ALGOL pro

  1. On automatic machine translation evaluation

    Directory of Open Access Journals (Sweden)

    Darinka Verdonik

    2013-05-01

    Full Text Available An important task of developing machine translation (MT is evaluating system performance. Automatic measures are most commonly used for this task, as manual evaluation is time-consuming and costly. However, to perform an objective evaluation is not a trivial task. Automatic measures, such as BLEU, TER, NIST, METEOR etc., have their own weaknesses, while manual evaluations are also problematic since they are always to some extent subjective. In this paper we test the influence of a test set on the results of automatic MT evaluation for the subtitling domain. Translating subtitles is a rather specific task for MT, since subtitles are a sort of summarization of spoken text rather than a direct translation of (written text. Additional problem when translating language pair that does not include English, in our example Slovene-Serbian, is that commonly the translations are done from English to Serbian and from English to Slovenian, and not directly, since most of the TV production is originally filmed in English. All this poses additional challenges to MT and consequently to MT evaluation. Automatic evaluation is based on a reference translation, which is usually taken from an existing parallel corpus and marked as a test set. In our experiments, we compare the evaluation results for the same MT system output using three types of test set. In the first round, the test set are 4000 subtitles from the parallel corpus of subtitles SUMAT. These subtitles are not direct translations from Serbian to Slovene or vice versa, but are based on an English original. In the second round, the test set are 1000 subtitles randomly extracted from the first test set and translated anew, from Serbian to Slovenian, based solely on the Serbian written subtitles. In the third round, the test set are the same 1000 subtitles, however this time the Slovene translations were obtained by manually correcting the Slovene MT outputs so that they are correct translations of the

  2. Automatic Evaluation of Machine Translation

    DEFF Research Database (Denmark)

    Martinez, Mercedes Garcia; Koglin, Arlene; Mesa-Lao, Bartolomé

    2015-01-01

    of quality criteria in as few edits as possible. The quality of MT systems is generally measured by automatic metrics, producing scores that should correlate with human evaluation.In this study, we investigate correlations between one of such metrics, i.e. Translation Edit Rate (TER), and actual post...... of post-editing effort, namely i) temporal (time), ii) cognitive (mental processes) and iii) technical (keyboard activity). For the purposes of this research, TER scores were correlated with two different indicators of post-editing effort as computed in the CRITT Translation Process Database (TPR...

  3. Annual review in automatic programming

    CERN Document Server

    Goodman, Richard

    2014-01-01

    Annual Review in Automatic Programming, Volume 2 is a collection of papers that discusses the controversy about the suitability of COBOL as a common business oriented language, and the development of different common languages for scientific computation. A couple of papers describes the use of the Genie system in numerical calculation and analyzes Mercury autocode in terms of a phrase structure language, such as in the source language, target language, the order structure of ATLAS, and the meta-syntactical language of the assembly program. Other papers explain interference or an ""intermediate

  4. Coordinated hybrid automatic repeat request

    KAUST Repository

    Makki, Behrooz

    2014-11-01

    We develop a coordinated hybrid automatic repeat request (HARQ) approach. With the proposed scheme, if a user message is correctly decoded in the first HARQ rounds, its spectrum is allocated to other users, to improve the network outage probability and the users\\' fairness. The results, which are obtained for single- and multiple-antenna setups, demonstrate the efficiency of the proposed approach in different conditions. For instance, with a maximum of M retransmissions and single transmit/receive antennas, the diversity gain of a user increases from M to (J+1)(M-1)+1 where J is the number of users helping that user.

  5. Motor automaticity in Parkinson’s disease

    Science.gov (United States)

    Wu, Tao; Hallett, Mark; Chan, Piu

    2017-01-01

    Bradykinesia is the most important feature contributing to motor difficulties in Parkinson’s disease (PD). However, the pathophysiology underlying bradykinesia is not fully understood. One important aspect is that PD patients have difficulty in performing learned motor skills automatically, but this problem has been generally overlooked. Here we review motor automaticity associated motor deficits in PD, such as reduced arm swing, decreased stride length, freezing of gait, micrographia and reduced facial expression. Recent neuroimaging studies have revealed some neural mechanisms underlying impaired motor automaticity in PD, including less efficient neural coding of movement, failure to shift automated motor skills to the sensorimotor striatum, instability of the automatic mode within the striatum, and use of attentional control and/or compensatory efforts to execute movements usually performed automatically in healthy people. PD patients lose previously acquired automatic skills due to their impaired sensorimotor striatum, and have difficulty in acquiring new automatic skills or restoring lost motor skills. More investigations on the pathophysiology of motor automaticity, the effect of L-dopa or surgical treatments on automaticity, and the potential role of using measures of automaticity in early diagnosis of PD would be valuable. PMID:26102020

  6. Edge Detection and Shape Recognition in Neutron Transmission Images

    International Nuclear Information System (INIS)

    Sword, Eric D.; McConchie, Seth M.

    2012-01-01

    Neutron transmission measurements are a valuable tool for nondestructively imaging special nuclear materials. Analysis of these images, however, tends to require significant user interaction to determine the sizes, shapes, and likely compositions of measured objects. Computer vision (CV) techniques can be a useful approach to automatically extracting important information from either neutron transmission images or fission-site-mapping images. An automatable approach has been developed that processes an input image and, through recursive application of CV techniques, produces a set of basic shapes that define surfaces observed in the image. These shapes can then be compared to a library of known shape configurations to determine if the measured object matches its expected configuration, as could be done behind an information barrier for arms control treaty verification inspections.

  7. Research about an automatic timing count system based on LabView

    International Nuclear Information System (INIS)

    Yan Jie; Liu Rong; Jian Li; Lu Xinxin; Zhu Tonghua; Wang Mei; Wen Zhongwei; Lin Jufang; Li Cheng

    2009-01-01

    Based on the LabView Virtual Instrument Development Platform and the GPIB instrument control and data transmission bus protocol, the design and research of a virtual instrument about an automatic timing count system using ORTEC 974 Counter/Timer is introduced in this paper. Comparing with the real instrument, the virtual instrument system enriched the timing count function and carried out the remote control of the real instrument. The counts and measured time can be recorded automatically during the measurement process for the further analysis and processing. (authors)

  8. Understanding Ebola Virus Transmission

    Directory of Open Access Journals (Sweden)

    Seth Judson

    2015-02-01

    Full Text Available An unprecedented number of Ebola virus infections among healthcare workers and patients have raised questions about our understanding of Ebola virus transmission. Here, we explore different routes of Ebola virus transmission between people, summarizing the known epidemiological and experimental data. From this data, we expose important gaps in Ebola virus research pertinent to outbreak situations. We further propose experiments and methods of data collection that will enable scientists to fill these voids in our knowledge about the transmission of Ebola virus.

  9. An automatic holographic adaptive phoropter

    Science.gov (United States)

    Amirsolaimani, Babak; Peyghambarian, N.; Schwiegerling, Jim; Bablumyan, Arkady; Savidis, Nickolaos; Peyman, Gholam

    2017-08-01

    Phoropters are the most common instrument used to detect refractive errors. During a refractive exam, lenses are flipped in front of the patient who looks at the eye chart and tries to read the symbols. The procedure is fully dependent on the cooperation of the patient to read the eye chart, provides only a subjective measurement of visual acuity, and can at best provide a rough estimate of the patient's vision. Phoropters are difficult to use for mass screenings requiring a skilled examiner, and it is hard to screen young children and the elderly etc. We have developed a simplified, lightweight automatic phoropter that can measure the optical error of the eye objectively without requiring the patient's input. The automatic holographic adaptive phoropter is based on a Shack-Hartmann wave front sensor and three computercontrolled fluidic lenses. The fluidic lens system is designed to be able to provide power and astigmatic corrections over a large range of corrections without the need for verbal feedback from the patient in less than 20 seconds.

  10. Automatic welding machine for piping

    International Nuclear Information System (INIS)

    Yoshida, Kazuhiro; Koyama, Takaichi; Iizuka, Tomio; Ito, Yoshitoshi; Takami, Katsumi.

    1978-01-01

    A remotely controlled automatic special welding machine for piping was developed. This machine is utilized for long distance pipe lines, chemical plants, thermal power generating plants and nuclear power plants effectively from the viewpoint of good quality control, reduction of labor and good controllability. The function of this welding machine is to inspect the shape and dimensions of edge preparation before welding work by the sense of touch, to detect the temperature of melt pool, inspect the bead form by the sense of touch, and check the welding state by ITV during welding work, and to grind the bead surface and inspect the weld metal by ultrasonic test automatically after welding work. The construction of this welding system, the main specification of the apparatus, the welding procedure in detail, the electrical source of this welding machine, the cooling system, the structure and handling of guide ring, the central control system and the operating characteristics are explained. The working procedure and the effect by using this welding machine, and the application to nuclear power plants and the other industrial field are outlined. The HIDIC 08 is used as the controlling computer. This welding machine is useful for welding SUS piping as well as carbon steel piping. (Nakai, Y.)

  11. SRV-automatic handling device

    International Nuclear Information System (INIS)

    Yamada, Koji

    1987-01-01

    Automatic handling device for the steam relief valves (SRV's) is developed in order to achieve a decrease in exposure of workers, increase in availability factor, improvement in reliability, improvement in safety of operation, and labor saving. A survey is made during a periodical inspection to examine the actual SVR handling operation. An SRV automatic handling device consists of four components: conveyor, armed conveyor, lifting machine, and control/monitoring system. The conveyor is so designed that the existing I-rail installed in the containment vessel can be used without any modification. This is employed for conveying an SRV along the rail. The armed conveyor, designed for a box rail, is used for an SRV installed away from the rail. By using the lifting machine, an SRV installed away from the I-rail is brought to a spot just below the rail so that the SRV can be transferred by the conveyor. The control/monitoring system consists of a control computer, operation panel, TV monitor and annunciator. The SRV handling device is operated by remote control from a control room. A trial equipment is constructed and performance/function testing is carried out using actual SRV's. As a result, is it shown that the SRV handling device requires only two operators to serve satisfactorily. The required time for removal and replacement of one SRV is about 10 minutes. (Nogami, K.)

  12. Automatic scanning of emulsion films

    International Nuclear Information System (INIS)

    D'Ambrosio, N.; Mandrioli, G.; Sirrib, G.

    2003-01-01

    The use of nuclear emulsions in recent large neutrino experiments is mostly due to the significant results in the developments of this detection technique. In the emulsion films, trajectories of through-going particles are permanently recorded: thus, the emulsion target can be considered not only as a tracking but also as a storing device. If the data readout is performed by automatic scanning systems interfaced to an acquisition computer equipped with a fast frame grabber, nuclear emulsions can be used as very large target detector and quickly analyzed in particle physics experiments. Techniques for automatic scanning of nuclear emulsions have been developed in the early past. The effort was initiated by Niwa at Nagoya (Japan) in the late 70s. The first large-scale application was the CHORUS experiment; then emulsions have been used to search for T neutrinos in a high track density environment like DONUT. In order to measure with high accuracy and high speed, very strict constraints must be satisfied in terms of mechanical precisions, camera speed, image processing power. Recent improvements in this technique are briefly reported

  13. Automatic generation of tourist brochures

    KAUST Repository

    Birsak, Michael

    2014-05-01

    We present a novel framework for the automatic generation of tourist brochures that include routing instructions and additional information presented in the form of so-called detail lenses. The first contribution of this paper is the automatic creation of layouts for the brochures. Our approach is based on the minimization of an energy function that combines multiple goals: positioning of the lenses as close as possible to the corresponding region shown in an overview map, keeping the number of lenses low, and an efficient numbering of the lenses. The second contribution is a route-aware simplification of the graph of streets used for traveling between the points of interest (POIs). This is done by reducing the graph consisting of all shortest paths through the minimization of an energy function. The output is a subset of street segments that enable traveling between all the POIs without considerable detours, while at the same time guaranteeing a clutter-free visualization. © 2014 The Author(s) Computer Graphics Forum © 2014 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd.

  14. Automaticity in reading isiZulu

    OpenAIRE

    Sandra Land

    2016-01-01

    Automaticity, or instant recognition of combinations of letters as units of language, is essential for proficient reading in any language. The article explores automaticity amongst competent adult first-language readers of isiZulu, and the factors associated with it or its opposite - active decoding. Whilst the transparent spelling patterns of isiZulu aid learner readers, some of its orthographical features may militate against their gaining automaticity. These features are agglutination; a c...

  15. Kansas Electric Transmission Lines

    Data.gov (United States)

    Kansas Data Access and Support Center — This data set is a digital representation of the EletcircTransmission lines for the State of Kansas as maintained by the Kansas Corporation Commission. Data is...

  16. Transmission issues in Alberta

    International Nuclear Information System (INIS)

    Levson, D.

    2002-01-01

    This paper outlined the major issues and concerns facing users of the transmission system in Alberta. They include congestion management issues that make investors uncertain about power generation. It is necessary to know the difference between which transmission price signals will be faced by low cost cogeneration at Fort McMurray and Cold Lake coal-fired generation near Edmonton compared to combined cycle gas generation near Calgary. Import and export policy tariffs are another concern. Most new generation opportunities in Alberta require access to export markets, but transmission facilities for export need policy support and appropriate tariffs. It was noted that the past actions of Alberta's Transmission Administrator and balancing pool may be distorting market signals for ancillary service markets, and that loss studies and calculations need upgrading

  17. Electric Power Transmission Lines

    Data.gov (United States)

    Department of Homeland Security — Transmission Lines are the system of structures, wires, insulators and associated hardware that carry electric energy from one point to another in an electric power...

  18. Watching Handball Transmissions

    DEFF Research Database (Denmark)

    Frandsen, Kirsten

    2010-01-01

    The current article presents a qualitative study of Danish television viewer’s reception of Danish handball transmissions. The overall aim of the study has been to contribute to a more nuanced understanding of televised sport as a specific kind of television entertainment. The analysis shows that......, due to the dramaturgic structure of handball transmissions, viewers consider such transmissions particularly reliable and effective sources of entertainment. The transmissions’ entertainment value derives from their specific ability to give the viewers a complex experience of feeling autonomous...... and competent when mastering the game and in relation to others. The study shows that entertainment concerns both affective involvement and identity formation, as social and cultural meaning seem to be at the root of involvement. Even though both men and women find great joy in the transmissions, their viewing...

  19. Eliminating Perinatal HIV Transmission

    Centers for Disease Control (CDC) Podcasts

    2012-11-26

    In this podcast, CDC’s Dr. Steve Nesheim discusses perinatal HIV transmission, including the importance of preventing HIV among women, preconception care, and timely HIV testing of the mother. Dr. Nesheim also introduces the revised curriculum Eliminating Perinatal HIV Transmission intended for faculty of OB/GYN and pediatric residents and nurse midwifery students.  Created: 11/26/2012 by Division of HIV/AIDS Prevention.   Date Released: 11/26/2012.

  20. Automatic Thermal Infrared Panoramic Imaging Sensor

    National Research Council Canada - National Science Library

    Gutin, Mikhail; Tsui, Eddy K; Gutin, Olga; Wang, Xu-Ming; Gutin, Alexey

    2006-01-01

    .... Automatic detection, location, and tracking of targets outside protected area ensures maximum protection and at the same time reduces the workload on personnel, increases reliability and confidence...

  1. National transmission grid study

    Energy Technology Data Exchange (ETDEWEB)

    Abraham, Spencer [USDOE Office of the Secretary of Energy, Washington, DC (United States)

    2003-05-31

    The National Energy Policy Plan directed the U.S. Department of Energy (DOE) to conduct a study to examine the benefits of establishing a national electricity transmission grid and to identify transmission bottlenecks and measures to address them. DOE began by conducting an independent analysis of U.S. electricity markets and identifying transmission system bottlenecks using DOE’s Policy Office Electricity Modeling System (POEMS). DOE’s analysis, presented in Section 2, confirms the central role of the nation’s transmission system in lowering costs to consumers through increased trade. More importantly, DOE’s analysis also confirms the results of previous studies, which show that transmission bottlenecks and related transmission system market practices are adding hundreds of millions of dollars to consumers’ electricity bills each year. A more detailed technical overview of the use of POEMS is provided in Appendix A. DOE led an extensive, open, public input process and heard a wide range of comments and recommendations that have all been considered.1 More than 150 participants registered for three public workshops held in Detroit, MI (September 24, 2001); Atlanta, GA (September 26, 2001); and Phoenix, AZ (September 28, 2001).

  2. Automatic gamma spectrometry analytical apparatus

    International Nuclear Information System (INIS)

    Lamargot, J.-P.; Wanin, Maurice.

    1980-01-01

    This invention falls within the area of quantitative or semi-quantitative analysis by gamma spectrometry and particularly refers to a device for bringing the samples into the counting position. The purpose of this invention is precisely to provide an automatic apparatus specifically adapted to the analysis of hard gamma radiations. To this effect, the invention relates to a gamma spectrometry analytical device comprising a lead containment, a detector of which the sensitive part is located inside the containment and additionally comprising a transfer system for bringing the analyzed samples in succession to a counting position inside the containment above the detector. A feed compartment enables the samples to be brought in turn one by one on to the transfer system through a duct connecting the compartment to the transfer system. Sequential systems for the coordinated forward feed of the samples in the compartment and the transfer system complete this device [fr

  3. Automatic validation of numerical solutions

    DEFF Research Database (Denmark)

    Stauning, Ole

    1997-01-01

    , using this method has been developed. (ADIODES is an abbreviation of `` Automatic Differentiation Interval Ordinary Differential Equation Solver''). ADIODES is used to prove existence and uniqueness of periodic solutions to specific ordinary differential equations occuring in dynamical systems theory....... These proofs of existence and uniqueness are difficult or impossible to obtain using other known methods. Also, a method for solving boundary value problems is described. Finally a method for enclosing solutions to a class of integral equations is described. This method is based on the mean value enclosure...... of an integral operator and uses interval Bernstein polynomials for enclosing the solution. Two numerical examples are given, using two orders of approximation and using different numbers of discretization points....

  4. Antares automatic beam alignment system

    International Nuclear Information System (INIS)

    Appert, Q.; Swann, T.; Sweatt, W.; Saxman, A.

    1980-01-01

    Antares is a 24-beam-line CO 2 laser system for controlled fusion research, under construction at Los Alamos Scientific Laboratory (LASL). Rapid automatic alignment of this system is required prior to each experiment shot. The alignment requirements, operational constraints, and a developed prototype system are discussed. A visible-wavelength alignment technique is employed that uses a telescope/TV system to view point light sources appropriately located down the beamline. Auto-alignment is accomplished by means of a video centroid tracker, which determines the off-axis error of the point sources. The error is nulled by computer-driven, movable mirrors in a closed-loop system. The light sources are fiber-optic terminations located at key points in the optics path, primarily at the center of large copper mirrors, and remotely illuminated to reduce heating effects

  5. Automatic quantification of iris color

    DEFF Research Database (Denmark)

    Christoffersen, S.; Harder, Stine; Andersen, J. D.

    2012-01-01

    An automatic algorithm to quantify the eye colour and structural information from standard hi-resolution photos of the human iris has been developed. Initially, the major structures in the eye region are identified including the pupil, iris, sclera, and eyelashes. Based on this segmentation, the ...... is completely data driven and it can divide a group of eye images into classes based on structure, colour or a combination of the two. The methods have been tested on a large set of photos with promising results....... regions. The result is a blue-brown ratio for each eye. Furthermore, an image clustering approach has been used with promising results. The approach is based on using a sparse dictionary of feature vectors learned from a training set of iris regions. The feature vectors contain both local structural...

  6. Automatic creation of simulation configuration

    International Nuclear Information System (INIS)

    Oudot, G.; Poizat, F.

    1993-01-01

    SIPA, which stands for 'Simulator for Post Accident', includes: 1) a sophisticated software oriented workshop SWORD (which stands for 'Software Workshop Oriented towards Research and Development') designed in the ADA language including integrated CAD system and software tools for automatic generation of simulation software and man-machine interface in order to operate run-time simulation; 2) a 'simulator structure' based on hardware equipment and software for supervision and communications; 3) simulation configuration generated by SWORD, operated under the control of the 'simulator structure' and run on a target computer. SWORD has already been used to generate two simulation configurations (French 900 MW and 1300 MW nuclear power plants), which are now fully operational on the SIPA training simulator. (Z.S.) 1 ref

  7. Computerized automatic tip scanning operation

    International Nuclear Information System (INIS)

    Nishikawa, K.; Fukushima, T.; Nakai, H.; Yanagisawa, A.

    1984-01-01

    In BWR nuclear power stations the Traversing Incore Probe (TIP) system is one of the most important components in reactor monitoring and control. In previous TIP systems, however, operators have suffered from the complexity of operation and long operation time required. The system presented in this paper realizes the automatic operation of the TIP system by monitoring and driving it with a process computer. This system significantly reduces the burden on customer operators and improves plant efficiency by simplifying the operating procedure, augmenting the accuracy of the measured data, and shortening operating time. The process computer is one of the PODIA (Plant Operation by Displayed Information Automation) systems. This computer transfers control signals to the TIP control panel, which in turn drives equipment by microprocessor control. The process computer contains such components as the CRT/KB unit, the printer plotter, the hard copier, and the message typers required for efficient man-machine communications. Its operation and interface properties are described

  8. Automatic Differentiation and Deep Learning

    CERN Multimedia

    CERN. Geneva

    2018-01-01

    Statistical learning has been getting more and more interest from the particle-physics community in recent times, with neural networks and gradient-based optimization being a focus. In this talk we shall discuss three things: automatic differention tools: tools to quickly build DAGs of computation that are fully differentiable. We shall focus on one such tool "PyTorch".  Easy deployment of trained neural networks into large systems with many constraints: for example, deploying a model at the reconstruction phase where the neural network has to be integrated into CERN's bulk data-processing C++-only environment Some recent models in deep learning for segmentation and generation that might be useful for particle physics problems.

  9. Automatic segmentation of diatom images for classification

    NARCIS (Netherlands)

    Jalba, Andrei C.; Wilkinson, Michael H.F.; Roerdink, Jos B.T.M.

    A general framework for automatic segmentation of diatom images is presented. This segmentation is a critical first step in contour-based methods for automatic identification of diatoms by computerized image analysis. We review existing results, adapt popular segmentation methods to this difficult

  10. Solar Powered Automatic Shrimp Feeding System

    Directory of Open Access Journals (Sweden)

    Dindo T. Ani

    2015-12-01

    Full Text Available - Automatic system has brought many revolutions in the existing technologies. One among the technologies, which has greater developments, is the solar powered automatic shrimp feeding system. For instance, the solar power which is a renewable energy can be an alternative solution to energy crisis and basically reducing man power by using it in an automatic manner. The researchers believe an automatic shrimp feeding system may help solve problems on manual feeding operations. The project study aimed to design and develop a solar powered automatic shrimp feeding system. It specifically sought to prepare the design specifications of the project, to determine the methods of fabrication and assembly, and to test the response time of the automatic shrimp feeding system. The researchers designed and developed an automatic system which utilizes a 10 hour timer to be set in intervals preferred by the user and will undergo a continuous process. The magnetic contactor acts as a switch connected to the 10 hour timer which controls the activation or termination of electrical loads and powered by means of a solar panel outputting electrical power, and a rechargeable battery in electrical communication with the solar panel for storing the power. By undergoing through series of testing, the components of the modified system were proven functional and were operating within the desired output. It was recommended that the timer to be used should be tested to avoid malfunction and achieve the fully automatic system and that the system may be improved to handle changes in scope of the project.

  11. Towards Automatic Trunk Classification on Young Conifers

    DEFF Research Database (Denmark)

    Petri, Stig; Immerkær, John

    2009-01-01

    In the garden nursery industry providing young Nordmann firs for Christmas tree plantations, there is a rising interest in automatic classification of their products to ensure consistently high quality and reduce the cost of manual labor. This paper describes a fully automatic single-view algorithm...

  12. Equipment for fully automatic radiographic pipe inspection

    International Nuclear Information System (INIS)

    Basler, G.; Sperl, H.; Weinschenk, K.

    1977-01-01

    The patent describes a device for fully automatic radiographic testing of large pipes with longitudinal welds. Furthermore the invention enables automatic marking of films in radiographic inspection with regard to a ticketing of the test piece and of that part of it where testing took place. (RW) [de

  13. Automatic face morphing for transferring facial animation

    NARCIS (Netherlands)

    Bui Huu Trung, B.H.T.; Bui, T.D.; Poel, Mannes; Heylen, Dirk K.J.; Nijholt, Antinus; Hamza, H.M.

    2003-01-01

    In this paper, we introduce a novel method of automatically finding the training set of RBF networks for morphing a prototype face to represent a new face. This is done by automatically specifying and adjusting corresponding feature points on a target face. The RBF networks are then used to transfer

  14. Building-transmission factors

    International Nuclear Information System (INIS)

    Woolson, W.A.; Marcum, J.; Scott, W.H.; Staggs, V.E.

    1982-01-01

    Parametric representations (called the nine-parameter formula) of the measurements of the radiation transmission through Japanese house models at the BREN reactor and 60 Co experiments are used to correct the free-in-air (FIA) T65 dose values for buildings shielding in the built-up residential areas at Hiroshima and Nagasaki. The accuracy of transmission factors derived from the nine-parameter formula impact the accuracy of the final-exposure dose estimates in the same manner as the accuracy of weapon yield and FIA radiation transport. A preliminary investigation of the accuracy of these transmission factors, sponsored by the Defense Nuclear Agency, has focused primarily on the adequacy of the Bare Reactor Experiment, Nevada (BREN) radiation environments for producing transmission factor data relevant to the situations at Hiroshima and Nagasaki. In addition, the radiation equivalency of house models used at BREN to Japanese house models and the physical basis for the nine-parameter formula have been studied. This investigation has concluded that the average gamma-ray transmission factors based on the nine-parameter formula are probably too high by about a factor of 2. The large discrepancy between the nine-parameter formula and recent estimates results from the apparent failure to properly account for the large gamma-ray dose component caused by capture gamma rays produced in the house walls by the large neutron flux present at BREN

  15. Simple Automatic File Exchange (SAFE) to Support Low-Cost Spacecraft Operation via the Internet

    Science.gov (United States)

    Baker, Paul; Repaci, Max; Sames, David

    1998-01-01

    Various issues associated with Simple Automatic File Exchange (SAFE) are presented in viewgraph form. Specific topics include: 1) Packet telemetry, Internet IP networks and cost reduction; 2) Basic functions and technical features of SAFE; 3) Project goals, including low-cost satellite transmission to data centers to be distributed via an Internet; 4) Operations with a replicated file protocol; 5) File exchange operation; 6) Ground stations as gateways; 7) Lessons learned from demonstrations and tests with SAFE; and 8) Feedback and future initiatives.

  16. Aerosol Transmission of Filoviruses

    Directory of Open Access Journals (Sweden)

    Berhanu Mekibib

    2016-05-01

    Full Text Available Filoviruses have become a worldwide public health concern because of their potential for introductions into non-endemic countries through international travel and the international transport of infected animals or animal products. Since it was first identified in 1976, in the Democratic Republic of Congo (formerly Zaire and Sudan, the 2013–2015 western African Ebola virus disease (EVD outbreak is the largest, both by number of cases and geographical extension, and deadliest, recorded so far in medical history. The source of ebolaviruses for human index case(s in most outbreaks is presumptively associated with handling of bush meat or contact with fruit bats. Transmission among humans occurs easily when a person comes in contact with contaminated body fluids of patients, but our understanding of other transmission routes is still fragmentary. This review deals with the controversial issue of aerosol transmission of filoviruses.

  17. Poverty and price transmission

    DEFF Research Database (Denmark)

    Elleby, Christian

    A key parameter determining the welfare impact from a world market shock is the transmission elasticity which measures the average domestic response to an international price change. Many studies have estimated price transmission elasticities for a large number of countries but the variation...... in these estimates is so far largely unexplored. This paper proposes a model which explains a country's domestic price response to world market shocks in terms of its demand structure. The model delivers two testable predictions; price transmission is increasing in per capita food expenditure and in income...... inequality. The empirical analysis of price changes during the food crises confirms these predictions with a caveat. I find significant inverse U-shaped relationships between domestic food price growth in 2007-8 and 2010-11 and per capita food expenditure. Unequal countries also experienced higher price...

  18. Aerosol Transmission of Filoviruses.

    Science.gov (United States)

    Mekibib, Berhanu; Ariën, Kevin K

    2016-05-23

    Filoviruses have become a worldwide public health concern because of their potential for introductions into non-endemic countries through international travel and the international transport of infected animals or animal products. Since it was first identified in 1976, in the Democratic Republic of Congo (formerly Zaire) and Sudan, the 2013-2015 western African Ebola virus disease (EVD) outbreak is the largest, both by number of cases and geographical extension, and deadliest, recorded so far in medical history. The source of ebolaviruses for human index case(s) in most outbreaks is presumptively associated with handling of bush meat or contact with fruit bats. Transmission among humans occurs easily when a person comes in contact with contaminated body fluids of patients, but our understanding of other transmission routes is still fragmentary. This review deals with the controversial issue of aerosol transmission of filoviruses.

  19. Probabilistic transmission system planning

    CERN Document Server

    Li, Wenyuan

    2011-01-01

    "The book is composed of 12 chapters and three appendices, and can be divided into four parts. The first part includes Chapters 2 to 7, which discuss the concepts, models, methods and data in probabilistic transmission planning. The second part, Chapters 8 to 11, addresses four essential issues in probabilistic transmission planning applications using actual utility systems as examples. Chapter 12, as the third part, focuses on a special issue, i.e. how to deal with uncertainty of data in probabilistic transmission planning. The fourth part consists of three appendices, which provide the basic knowledge in mathematics for probabilistic planning. Please refer to the attached table of contents which is given in a very detailed manner"--

  20. Transmission positron microscopes

    International Nuclear Information System (INIS)

    Doyama, Masao; Kogure, Yoshiaki; Inoue, Miyoshi; Kurihara, Toshikazu; Yoshiie, Toshimasa; Oshima, Ryuichiro; Matsuya, Miyuki

    2006-01-01

    Immediate and near-future plans for transmission positron microscopes being built at KEK, Tsukuba, Japan, are described. The characteristic feature of this project is remolding a commercial electron microscope to a positron microscope. A point source of electrons kept at a negative high voltage is changed to a point source of positrons kept at a high positive voltage. Positional resolution of transmission microscopes should be theoretically the same as electron microscopes. Positron microscopes utilizing trapping of positrons have always positional ambiguity due to the diffusion of positrons

  1. Transmission grid security

    CERN Document Server

    Haarla, Liisa; Hirvonen, Ritva; Labeau, Pierre-Etienne

    2011-01-01

    In response to the growing importance of power system security and reliability, ""Transmission Grid Security"" proposes a systematic and probabilistic approach for transmission grid security analysis. The analysis presented uses probabilistic safety assessment (PSA) and takes into account the power system dynamics after severe faults. In the method shown in this book the power system states (stable, not stable, system breakdown, etc.) are connected with the substation reliability model. In this way it is possible to: estimate the system-wide consequences of grid faults; identify a chain of eve

  2. Design studies of continuously variable transmissions for electric vehicles

    Science.gov (United States)

    Parker, R. J.; Loewenthal, S. H.; Fischer, G. K.

    1981-01-01

    Preliminary design studies were performed on four continuously variable transmission (CVT) concepts for use with a flywheel equipped electric vehicle of 1700 kg gross weight. Requirements of the CVT's were a maximum torque of 450 N-m (330 lb-ft), a maximum output power of 75 kW (100 hp), and a flywheel speed range of 28,000 to 14,000 rpm. Efficiency, size, weight, cost, reliability, maintainability, and controls were evaluated for each of the four concepts which included a steel V-belt type, a flat rubber belt type, a toroidal traction type, and a cone roller traction type. All CVT's exhibited relatively high calculated efficiencies (68 percent to 97 percent) over a broad range of vehicle operating conditions. Estimated weight and size of these transmissions were comparable to or less than equivalent automatic transmission. The design of each concept was carried through the design layout stage.

  3. Railway automatic safety protection system based on GPS

    Directory of Open Access Journals (Sweden)

    Fu Hai Juan

    2016-01-01

    Full Text Available The automatic protection system of railway safety is designed for the railway construction workers to protect alarm, and the safety protection device by using GPS satellite positioning system to acquire location information of the operating point, through the CTC/TDCS system and computer monitoring system for the running of the train position and the arithmetic distance. Achieving timely and continuously forecasts about the distance of the train which is apart from the operating point to prompt the voice alarm of the approaching train. Using digital technology to realize the function of the traditional analog interphone, eliminates the quality problems of the call. With the GSM-R, mobile wireless transmission channel and terminal technology, it overcomes the restrictions of the analog interphone which influenced by communication distance and more problems of blind areas. Finally to achieve practical, convenient, applicable and adaptable design goals.

  4. Image-based mobile service: automatic text extraction and translation

    Science.gov (United States)

    Berclaz, Jérôme; Bhatti, Nina; Simske, Steven J.; Schettino, John C.

    2010-01-01

    We present a new mobile service for the translation of text from images taken by consumer-grade cell-phone cameras. Such capability represents a new paradigm for users where a simple image provides the basis for a service. The ubiquity and ease of use of cell-phone cameras enables acquisition and transmission of images anywhere and at any time a user wishes, delivering rapid and accurate translation over the phone's MMS and SMS facilities. Target text is extracted completely automatically, requiring no bounding box delineation or related user intervention. The service uses localization, binarization, text deskewing, and optical character recognition (OCR) in its analysis. Once the text is translated, an SMS message is sent to the user with the result. Further novelties include that no software installation is required on the handset, any service provider or camera phone can be used, and the entire service is implemented on the server side.

  5. Development of an Automatic Detection Program of Halo CMEs

    Science.gov (United States)

    Choi, K.; Park, M. Y.; Kim, J.

    2017-12-01

    The front-side halo CMEs are the major cause for large geomagnetic storms. Halo CMEs can result in damage to satellites, communication, electrical transmission lines and power systems. Thus automated techniques for detecting and analysing Halo CMEs from coronagraph data are of ever increasing importance for space weather monitoring and forecasting. In this study, we developed the algorithm that can automatically detect and do image processing the Halo CMEs in the images from the LASCO C3 coronagraph on board the SOHO spacecraft. With the detection algorithm, we derived the geometric and kinematical parameters of halo CMEs, such as source location, width, actual CME speed and arrival time at 21.5 solar radii.

  6. Automatic locking orthotic knee device

    Science.gov (United States)

    Weddendorf, Bruce C. (Inventor)

    1993-01-01

    An articulated tang in clevis joint for incorporation in newly manufactured conventional strap-on orthotic knee devices or for replacing such joints in conventional strap-on orthotic knee devices is discussed. The instant tang in clevis joint allows the user the freedom to extend and bend the knee normally when no load (weight) is applied to the knee and to automatically lock the knee when the user transfers weight to the knee, thus preventing a damaged knee from bending uncontrollably when weight is applied to the knee. The tang in clevis joint of the present invention includes first and second clevis plates, a tang assembly and a spacer plate secured between the clevis plates. Each clevis plate includes a bevelled serrated upper section. A bevelled shoe is secured to the tank in close proximity to the bevelled serrated upper section of the clevis plates. A coiled spring mounted within an oblong bore of the tang normally urges the shoes secured to the tang out of engagement with the serrated upper section of each clevic plate to allow rotation of the tang relative to the clevis plate. When weight is applied to the joint, the load compresses the coiled spring, the serrations on each clevis plate dig into the bevelled shoes secured to the tang to prevent relative movement between the tang and clevis plates. A shoulder is provided on the tang and the spacer plate to prevent overextension of the joint.

  7. Pattern-Driven Automatic Parallelization

    Directory of Open Access Journals (Sweden)

    Christoph W. Kessler

    1996-01-01

    Full Text Available This article describes a knowledge-based system for automatic parallelization of a wide class of sequential numerical codes operating on vectors and dense matrices, and for execution on distributed memory message-passing multiprocessors. Its main feature is a fast and powerful pattern recognition tool that locally identifies frequently occurring computations and programming concepts in the source code. This tool also works for dusty deck codes that have been "encrypted" by former machine-specific code transformations. Successful pattern recognition guides sophisticated code transformations including local algorithm replacement such that the parallelized code need not emerge from the sequential program structure by just parallelizing the loops. It allows access to an expert's knowledge on useful parallel algorithms, available machine-specific library routines, and powerful program transformations. The partially restored program semantics also supports local array alignment, distribution, and redistribution, and allows for faster and more exact prediction of the performance of the parallelized target code than is usually possible.

  8. Portable and Automatic Moessbauer Analysis

    International Nuclear Information System (INIS)

    Souza, P. A. de; Garg, V. K.; Klingelhoefer, G.; Gellert, R.; Guetlich, P.

    2002-01-01

    A portable Moessbauer spectrometer, developed for extraterrestrial applications, opens up new industrial applications of MBS. But for industrial applications, an available tool for fast data analysis is also required, and it should be easy to handle. The analysis of Moessbauer spectra and their parameters is a barrier for the popularity of this wide-applicable spectroscopic technique in industry. Based on experience, the analysis of a Moessbauer spectrum is time-consuming and requires the dedication of a specialist. However, the analysis of Moessbauer spectra, from the fitting to the identification of the sample phases, can be faster using by genetic algorithms, fuzzy logic and artificial neural networks. Industrial applications are very specific ones and the data analysis can be performed using these algorithms. In combination with an automatic analysis, the Moessbauer spectrometer can be used as a probe instrument which covers the main industrial needs for an on-line monitoring of its products, processes and case studies. Some of these real industrial applications will be discussed.

  9. Automatic segmentation of the colon

    Science.gov (United States)

    Wyatt, Christopher L.; Ge, Yaorong; Vining, David J.

    1999-05-01

    Virtual colonoscopy is a minimally invasive technique that enables detection of colorectal polyps and cancer. Normally, a patient's bowel is prepared with colonic lavage and gas insufflation prior to computed tomography (CT) scanning. An important step for 3D analysis of the image volume is segmentation of the colon. The high-contrast gas/tissue interface that exists in the colon lumen makes segmentation of the majority of the colon relatively easy; however, two factors inhibit automatic segmentation of the entire colon. First, the colon is not the only gas-filled organ in the data volume: lungs, small bowel, and stomach also meet this criteria. User-defined seed points placed in the colon lumen have previously been required to spatially isolate only the colon. Second, portions of the colon lumen may be obstructed by peristalsis, large masses, and/or residual feces. These complicating factors require increased user interaction during the segmentation process to isolate additional colon segments. To automate the segmentation of the colon, we have developed a method to locate seed points and segment the gas-filled lumen with no user supervision. We have also developed an automated approach to improve lumen segmentation by digitally removing residual contrast-enhanced fluid resulting from a new bowel preparation that liquefies and opacifies any residual feces.

  10. Automatic panoramic thermal integrated sensor

    Science.gov (United States)

    Gutin, Mikhail A.; Tsui, Eddy K.; Gutin, Olga N.

    2005-05-01

    Historically, the US Army has recognized the advantages of panoramic imagers with high image resolution: increased area coverage with fewer cameras, instantaneous full horizon detection, location and tracking of multiple targets simultaneously, extended range, and others. The novel ViperViewTM high-resolution panoramic thermal imager is the heart of the Automatic Panoramic Thermal Integrated Sensor (APTIS), being jointly developed by Applied Science Innovative, Inc. (ASI) and the Armament Research, Development and Engineering Center (ARDEC) in support of the Future Combat Systems (FCS) and the Intelligent Munitions Systems (IMS). The APTIS is anticipated to operate as an intelligent node in a wireless network of multifunctional nodes that work together to improve situational awareness (SA) in many defense and offensive operations, as well as serve as a sensor node in tactical Intelligence Surveillance Reconnaissance (ISR). The ViperView is as an aberration-corrected omnidirectional imager with small optics designed to match the resolution of a 640x480 pixels IR camera with improved image quality for longer range target detection, classification, and tracking. The same approach is applicable to panoramic cameras working in the visible spectral range. Other components of the ATPIS sensor suite include ancillary sensors, advanced power management, and wakeup capability. This paper describes the development status of the APTIS system.

  11. Automatic segmentation of psoriasis lesions

    Science.gov (United States)

    Ning, Yang; Shi, Chenbo; Wang, Li; Shu, Chang

    2014-10-01

    The automatic segmentation of psoriatic lesions is widely researched these years. It is an important step in Computer-aid methods of calculating PASI for estimation of lesions. Currently those algorithms can only handle single erythema or only deal with scaling segmentation. In practice, scaling and erythema are often mixed together. In order to get the segmentation of lesions area - this paper proposes an algorithm based on Random forests with color and texture features. The algorithm has three steps. The first step, the polarized light is applied based on the skin's Tyndall-effect in the imaging to eliminate the reflection and Lab color space are used for fitting the human perception. The second step, sliding window and its sub windows are used to get textural feature and color feature. In this step, a feature of image roughness has been defined, so that scaling can be easily separated from normal skin. In the end, Random forests will be used to ensure the generalization ability of the algorithm. This algorithm can give reliable segmentation results even the image has different lighting conditions, skin types. In the data set offered by Union Hospital, more than 90% images can be segmented accurately.

  12. Optoacoustic temperature determination and automatic coagulation control in rabbits

    Science.gov (United States)

    Schlott, Kerstin; Koinzer, Stefan; Ptaszynski, Lars; Luft, Susanne; Baade, Alex; Bever, Marco; Roider, Johann; Birngruber, Reginald; Brinkmann, Ralf

    2011-03-01

    Retinal laser photocoagulation is an established treatment method for many retinal diseases like macula edema or diabetic retinopathy. The selection of the laser parameters is so far based on post treatment evaluation of the lesion size and strength. Due to local pigment variations in the fundus and individual transmission the same laser parameters often lead to an overtreatment. Optoacoustic allows a non invasive monitoring of the retinal temperature increase during retinal laser irradiation by measuring the temperature dependent pressure amplitudes, which are induced by short probe laser pulses. A 75 ns/ 523 nm Nd:YLF was used as a probe laser at a repetition rate of 1 kHz, and a cw / 532 nm treatment laser for heating. A contact lens was modified with a ring-shaped ultrasonic transducer to detect the pressure waves at the cornea. Temperatures were collected for irradiations leading to soft or invisible lesions. Based on this data the threshold for denaturation was found. By analyzing the initial temperature increase, the further temperature development during irradiation could be predicted. An algorithm was found to calculate the irradiation time, which is needed for a soft lesion formation, from the temperature curve. By this it was possible to provide a real-time dosimetry by automatically switching off the treatment laser after the calculated irradiation time. Automatically controlled coagulations appear softer and more uniformly.

  13. Intergenerational Transmission of Volunteering

    NARCIS (Netherlands)

    Bekkers, René

    2007-01-01

    In this article, I investigate the strength of intergenerational transmission of volunteering for non-profit associations in The Netherlands. Data from the Family Survey of the Dutch Population 2000 reveal that there are significant relations between current volunteering and parental volunteering in

  14. Scanning transmission electron microscope

    NARCIS (Netherlands)

    Kruit, P.

    2006-01-01

    The invention relates to a scanning transmission electron microscope comprising an electron source, an electron accelerator and deflection means for directing electrons emitted by the electron source at an object to be examined, and in addition a detector for detecting electrons coming from the

  15. Open access to transmission

    International Nuclear Information System (INIS)

    Keith, D.M.

    1996-01-01

    For the past 12 to 15 years, the US electric power and energy industry and its federal regulators have been going through a prolonged exercise leading to opening up the national interconnected transmission grid for all qualified wholesale users to have open and equal access. The debates have been painful in a sense that not all parties - especially some of the transmission system owning utilities - believe that the concept of Open Access is achievable, due to technical constraints on the systems. The present Open Access activity is limited to wholesales transaction under the federal jurisdiction, but several states are either experimenting with or considering retail wheeling. In fact, the FERC - Federal Energy Regulatory Commission - has already expanded its view to embrace retail transmission, if the retail transaction involves the use of the interstate transmission systems which are under FERC's jurisdiction. This paper delves into some of the results of the technical cost and pricing analysis for open access. The statutes and resulting regulations are not addressed herein. (author). 1 fig

  16. Drivers of Tuberculosis Transmission

    NARCIS (Netherlands)

    Mathema, Barun; Andrews, Jason R.; Cohen, Ted; Borgdorff, Martien W.; Behr, Marcel; Glynn, Judith R.; Rustomjee, Roxana; Silk, Benjamin J.; Wood, Robin

    2017-01-01

    Measuring tuberculosis transmission is exceedingly difficult, given the remarkable variability in the timing of clinical disease after Mycobacterium tuberculosis infection; incident disease can result from either a recent (ie, weeks to months) or a remote (ie, several years to decades) infection

  17. 4. CRIMINALISING HIV TRANSMISSION

    African Journals Online (AJOL)

    Esem

    Method: A comprehensive analysis of both global and. Zambianpublications, legislation and case laws was conducted. Results: Proponents of criminalisation of HIV transmission argue that criminalization would serve as a deterrent to the culprit and others to engage in prohibited conduct in future while the opponents argue ...

  18. A neurocomputational model of automatic sequence production.

    Science.gov (United States)

    Helie, Sebastien; Roeder, Jessica L; Vucovich, Lauren; Rünger, Dennis; Ashby, F Gregory

    2015-07-01

    Most behaviors unfold in time and include a sequence of submovements or cognitive activities. In addition, most behaviors are automatic and repeated daily throughout life. Yet, relatively little is known about the neurobiology of automatic sequence production. Past research suggests a gradual transfer from the associative striatum to the sensorimotor striatum, but a number of more recent studies challenge this role of the BG in automatic sequence production. In this article, we propose a new neurocomputational model of automatic sequence production in which the main role of the BG is to train cortical-cortical connections within the premotor areas that are responsible for automatic sequence production. The new model is used to simulate four different data sets from human and nonhuman animals, including (1) behavioral data (e.g., RTs), (2) electrophysiology data (e.g., single-neuron recordings), (3) macrostructure data (e.g., TMS), and (4) neurological circuit data (e.g., inactivation studies). We conclude with a comparison of the new model with existing models of automatic sequence production and discuss a possible new role for the BG in automaticity and its implication for Parkinson's disease.

  19. Automatic Recognition of Road Signs

    Science.gov (United States)

    Inoue, Yasuo; Kohashi, Yuuichirou; Ishikawa, Naoto; Nakajima, Masato

    2002-11-01

    The increase in traffic accidents is becoming a serious social problem with the recent rapid traffic increase. In many cases, the driver"s carelessness is the primary factor of traffic accidents, and the driver assistance system is demanded for supporting driver"s safety. In this research, we propose the new method of automatic detection and recognition of road signs by image processing. The purpose of this research is to prevent accidents caused by driver"s carelessness, and call attention to a driver when the driver violates traffic a regulation. In this research, high accuracy and the efficient sign detecting method are realized by removing unnecessary information except for a road sign from an image, and detect a road sign using shape features. At first, the color information that is not used in road signs is removed from an image. Next, edges except for circular and triangle ones are removed to choose sign shape. In the recognition process, normalized cross correlation operation is carried out to the two-dimensional differentiation pattern of a sign, and the accurate and efficient method for detecting the road sign is realized. Moreover, the real-time operation in a software base was realized by holding down calculation cost, maintaining highly precise sign detection and recognition. Specifically, it becomes specifically possible to process by 0.1 sec(s)/frame using a general-purpose PC (CPU: Pentium4 1.7GHz). As a result of in-vehicle experimentation, our system could process on real time and has confirmed that detection and recognition of a sign could be performed correctly.

  20. Automatic adjustment of astrochronologic correlations

    Science.gov (United States)

    Zeeden, Christian; Kaboth, Stefanie; Hilgen, Frederik; Laskar, Jacques

    2017-04-01

    Here we present an algorithm for the automated adjustment and optimisation of correlations between proxy data and an orbital tuning target (or similar datasets as e.g. ice models) for the R environment (R Development Core Team 2008), building on the 'astrochron' package (Meyers et al.2014). The basis of this approach is an initial tuning on orbital (precession, obliquity, eccentricity) scale. We use filters of orbital frequency ranges related to e.g. precession, obliquity or eccentricity of data and compare these filters to an ensemble of target data, which may consist of e.g. different combinations of obliquity and precession, different phases of precession and obliquity, a mix of orbital and other data (e.g. ice models), or different orbital solutions. This approach allows for the identification of an ideal mix of precession and obliquity to be used as tuning target. In addition, the uncertainty related to different tuning tie points (and also precession- and obliquity contributions of the tuning target) can easily be assessed. Our message is to suggest an initial tuning and then obtain a reproducible tuned time scale, avoiding arbitrary chosen tie points and replacing these by automatically chosen ones, representing filter maxima (or minima). We present and discuss the above outlined approach and apply it to artificial and geological data. Artificial data are assessed to find optimal filter settings; real datasets are used to demonstrate the possibilities of such an approach. References: Meyers, S.R. (2014). Astrochron: An R Package for Astrochronology. http://cran.r-project.org/package=astrochron R Development Core Team (2008). R: A language and environment for statistical computing. R Foundation for Statistical Computing, Vienna, Austria. ISBN 3-900051-07-0, URL http://www.R-project.org.

  1. 12th Portuguese Conference on Automatic Control

    CERN Document Server

    Soares, Filomena; Moreira, António

    2017-01-01

    The biennial CONTROLO conferences are the main events promoted by The CONTROLO 2016 – 12th Portuguese Conference on Automatic Control, Guimarães, Portugal, September 14th to 16th, was organized by Algoritmi, School of Engineering, University of Minho, in partnership with INESC TEC, and promoted by the Portuguese Association for Automatic Control – APCA, national member organization of the International Federation of Automatic Control – IFAC. The seventy-five papers published in this volume cover a wide range of topics. Thirty-one of them, of a more theoretical nature, are distributed among the first five parts: Control Theory; Optimal and Predictive Control; Fuzzy, Neural and Genetic Control; Modeling and Identification; Sensing and Estimation. The papers go from cutting-edge theoretical research to innovative control applications and show expressively how Automatic Control can be used to increase the well being of people. .

  2. 2010 United States Automatic Identification System Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2010 United States Automatic Identification System Database contains vessel traffic data for planning purposes within the U.S. coastal waters. The database is...

  3. 2014 United States Automatic Identification System Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2014 United States Automatic Identification System Database contains vessel traffic data for planning purposes within the U.S. coastal waters. The database is...

  4. 2011 United States Automatic Identification System Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2011 United States Automatic Identification System Database contains vessel traffic data for planning purposes within the U.S. coastal waters. The database is...

  5. 2009 United States Automatic Identification System Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2009 United States Automatic Identification System Database contains vessel traffic data for planning purposes within the U.S. coastal waters. The database is...

  6. 2012 United States Automatic Identification System Database

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The 2012 United States Automatic Identification System Database contains vessel traffic data for planning purposes within the U.S. coastal waters. The database is...

  7. Regional transmission subsystem planning

    Energy Technology Data Exchange (ETDEWEB)

    Costa Bortoni, Edson da [Quadrante Softwares Especializados Ltda., Itajuba, MG (Brazil); Bajay, Sergio Valdir; Barros Correia, Paulo de [Universidade Estadual de Campinas, SP (Brazil). Faculdade de Engenharia Mecanica; Santos, Afonso Henriques Moreira; Haddad, Jamil [Escola Federal de Engenharia de Itajuba, MG (Brazil)

    1994-12-31

    This work presents an approach for the planning of transmission systems by employing mixed--integer linear programming to obtain a cost and operating characteristics optimized system. The voltage loop equations are written in a modified form, so that, at the end of the analysis, the model behaves as a DC power flow, with the help of the two Kirchhoff`s laws, exempting the need of interaction with an external power flow program for analysis of the line loading. The model considers the occurrence of contingencies, so that the final result is a network robust to the most severe contingencies. This whole technique is adapted to the regional electric power transmission subsystems. (author) 9 refs., 4 figs.

  8. Mechanisms, Transmissions and Applications

    CERN Document Server

    Corves, Burkhard

    2012-01-01

    The first Workshop on Mechanisms, Transmissions and Applications -- MeTrApp-2011 was organized by the Mechatronics Department at the Mechanical Engineering Faculty, “Politehnica” University of Timisoara, Romania, under the patronage of the IFToMM Technical Committees Linkages and Mechanical Controls and Micromachines. The workshop brought together researchers and students who work in disciplines associated with mechanisms science and offered a great opportunity for scientists from all over the world to present their achievements, exchange innovative ideas and create solid international links, setting the trend for future developments in this important and creative field. The topics treated in this volume are mechanisms and machine design, mechanical transmissions, mechatronic and biomechanic applications, computational and experimental methods, history of mechanism and machine science and teaching methods.

  9. Automatic safety rod for reactors. [LMFBR

    Science.gov (United States)

    Germer, J.H.

    1982-03-23

    An automatic safety rod for a nuclear reactor containing neutron absorbing material and designed to be inserted into a reactor core after a loss-of-flow. Actuation is based upon either a sudden decrease in core pressure drop or the pressure drop decreases below a predetermined minimum value. The automatic control rod includes a pressure regulating device whereby a controlled decrease in operating pressure due to reduced coolant flow does not cause the rod to drop into the core.

  10. Automatic Control of Freeboard and Turbine Operation

    DEFF Research Database (Denmark)

    Kofoed, Jens Peter; Frigaard, Peter Bak; Friis-Madsen, Erik

    The report deals with the modules for automatic control of freeboard and turbine operation on board the Wave dragon, Nissum Bredning (WD-NB) prototype, and covers what has been going on up to ultimo 2003.......The report deals with the modules for automatic control of freeboard and turbine operation on board the Wave dragon, Nissum Bredning (WD-NB) prototype, and covers what has been going on up to ultimo 2003....

  11. Automatic and strategic processes in advertising effects

    DEFF Research Database (Denmark)

    Grunert, Klaus G.

    1996-01-01

    Two kinds of cognitive processes can be distinguished: Automatic processes, which are mostly subconscious, are learned and changed very slowly, and are not subject to the capacity limitations of working memory, and strategic processes, which are conscious, are subject to capacity limitations......, and can easily be adapted to situational circumstances. Both the perception of advertising and the way advertising influences brand evaluation involves both processes. Automatic processes govern the recognition of advertising stimuli, the relevance decision which determines further higher-level processing...

  12. Towards automatic verification of ladder logic programs

    OpenAIRE

    Zoubek , Bohumir; Roussel , Jean-Marc; Kwiatkowska , Martha

    2003-01-01

    International audience; Control system programs are usually validated by testing prior to their deployment. Unfortunately, testing is not exhaustive and therefore it is possible that a program which passed all the required tests still contains errors. In this paper we apply techniques of automatic verification to a control program written in ladder logic. A model is constructed mechanically from the ladder logic program and subjected to automatic verification against requirements that include...

  13. Automatic terrain modeling using transfinite element analysis

    KAUST Repository

    Collier, Nathan

    2010-05-31

    An automatic procedure for modeling terrain is developed based on L2 projection-based interpolation of discrete terrain data onto transfinite function spaces. The function space is refined automatically by the use of image processing techniques to detect regions of high error and the flexibility of the transfinite interpolation to add degrees of freedom to these areas. Examples are shown of a section of the Palo Duro Canyon in northern Texas.

  14. The problem of automatic identification of concepts

    International Nuclear Information System (INIS)

    Andreewsky, Alexandre

    1975-11-01

    This paper deals with the problem of the automatic recognition of concepts and describes an important language tool, the ''linguistic filter'', which facilitates the construction of statistical algorithms. Certain special filters, of prepositions, conjunctions, negatives, logical implication, compound words, are presented. This is followed by a detailed description of a statistical algorithm allowing recognition of pronoun referents, and finally the problem of the automatic treatment of negatives in French is discussed [fr

  15. Automatic control of commercial computer programs

    International Nuclear Information System (INIS)

    Rezvov, B.A.; Artem'ev, A.N.; Maevskij, A.G.; Demkiv, A.A.; Kirillov, B.F.; Belyaev, A.D.; Artem'ev, N.A.

    2010-01-01

    The way of automatic control of commercial computer programs is presented. The developed connection of the EXAFS spectrometer automatic system (which is managed by PC for DOS) is taken with the commercial program for the CCD detector control (which is managed by PC for Windows). The described complex system is used for the automation of intermediate amplitude spectra processing in EXAFS spectrum measurements at Kurchatov SR source

  16. Automatic penalty continuation in structural topology optimization

    DEFF Research Database (Denmark)

    Rojas Labanda, Susana; Stolpe, Mathias

    2015-01-01

    this issue is addressed. We propose an automatic continuation method, where the material penalization parameter is included as a new variable in the problem and a constraint guarantees that the requested penalty is eventually reached. The numerical results suggest that this approach is an appealing...... alternative to continuation methods. Automatic continuation also generally obtains better designs than the classical formulation using a reduced number of iterations....

  17. On the Energy Efficiency of Dual Clutch Transmissions and Automated Manual Transmissions

    Directory of Open Access Journals (Sweden)

    Fabio Vacca

    2017-10-01

    Full Text Available The main benefits of dual clutch transmissions (DCTs are: (i a higher energy efficiency than automatic transmission systems with torque converters; and (ii the capability to fill the torque gap during gear shifts to allow seamless longitudinal acceleration profiles. Therefore, DCTs are viable alternatives to automated manual transmissions (AMTs. For vehicles equipped with engines that can generate considerable torque, large clutch-slip energy losses occur during power-on gear shifts and, as a result, DCTs need wet clutches for effective heat dissipation. This requirement substantially reduces DCT efficiency because of the churning and ancillary power dissipations associated with the wet clutch pack. To the knowledge of the authors, this study is the first to analyse the detailed power loss contributions of a DCT with wet clutches, and their relative significance along a set of driving cycles. Based on these results, a novel hybridised AMT (HAMT with a single dry clutch and an electric motor is proposed for the same vehicle. The HAMT architecture combines the high mechanical efficiency typical of AMTs with a single dry clutch, with the torque-fill capability and operational flexibility allowed by the electric motor. The measured efficiency maps of a case study DCT and HAMT are compared. This is then complemented by the analysis of the respective fuel consumption along the driving cycles, which is simulated with an experimentally validated vehicle model. In its internal combustion engine mode, the HAMT reduces fuel consumption by >9% with respect to the DCT.

  18. Available transmission capacity assessment

    Directory of Open Access Journals (Sweden)

    Škokljev Ivan

    2012-01-01

    Full Text Available Effective power system operation requires the analysis of vast amounts of information. Power market activities expose power transmission networks to high-level power transactions that threaten normal, secure operation of the power system. When there are service requests for a specific sink/source pair in a transmission system, the transmission system operator (TSO must allocate the available transfer capacity (ATC. It is common that ATC has a single numerical value. Additionally, the ATC must be calculated for the base case configuration of the system, while generation dispatch and topology remain unchanged during the calculation. Posting ATC on the internet should benefit prospective users by aiding them in formulating their requests. However, a single numerical value of ATC offers little for prospect for analysis, planning, what-if combinations, etc. A symbolic approach to the power flow problem (DC power flow and ATC offers a numerical computation at the very end, whilst the calculation beforehand is performed by using symbols for the general topology of the electrical network. Qualitative analysis of the ATC using only qualitative values, such as increase, decrease or no change, offers some new insights into ATC evaluation, multiple transactions evaluation, value of counter-flows and their impact etc. Symbolic analysis in this paper is performed after the execution of the linear, symbolic DC power flow. As control variables, the mathematical model comprises linear security constraints, ATC, PTDFs and transactions. The aim is to perform an ATC sensitivity study on a five nodes/seven lines transmission network, used for zonal market activities tests. A relatively complicated environment with twenty possible bilateral transactions is observed.

  19. Operational electricity transmission rates

    International Nuclear Information System (INIS)

    Roggen, M.

    1997-01-01

    In a liberalized electricity market both the consumers and the producers of electricity must pay for the use of the power transmission network. Thus, the net manager has unlimited options to realize efficiency improvements. A neutral and transparent management of the power grid is necessary to avoid disturbance of the market. KEMA Consulting translated abstract ideas and strategic advices to operational concepts in its report 'A framework for the determination of tariffs of the transport in the Dutch electricity sector'

  20. LVDS tester: a systematic test of cable signal transmission at the ALICE experiment

    Energy Technology Data Exchange (ETDEWEB)

    Barnby, L; Bhasin, A; Evans, D; Jones, G T; Jones, P G; Jovanovic, P; Jusko, A; Kour, R; Krivda, M; Lazzeroni, C; Lietava, R; Matthews, Z L; Navin, S; Palaha, A; Petrov, P; Platt, R; Scott, P [School of Physics and Astronomy, University of Birmingham, Birmingham (United Kingdom); Bombara, M [Faculty of Science, P.J. Safarik University, Kosice (Slovakia); Kralik, I; Sandor, L, E-mail: Daniel.Tapia.Takaki@cern.ch [Institute of Experimental Physics, Slovak Academy of Sciences, Kosice (Slovakia)

    2010-12-15

    In the ALICE experiment, the Low-Voltage Differential Signalling (LVDS) format is used for the transmission of trigger inputs from the detectors to the Central Trigger Processor (CTP), the L0 trigger outputs from Local Trigger Units (LTU) boards back to the detectors and the BUSY inputs from the sub-detectors to the CTP. ALICE has designed a set-up, called the LVDS transmission tester, that aims to measure various transmission quality parameters and the bit-error rate (BER) for long period runs in an automatic way. In this paper, this method is described and the conclusions from these tests for the ALICE LVDS cables are discussed.

  1. LVDS tester: a systematic test of cable signal transmission at the ALICE experiment

    CERN Document Server

    Barnby, L; Bombara, M; Evans, D; Jones, G T; Jones, P G; Jovanović, P; Jusko, A; Kour, R; Králik, I; Krivda, M; Lazzeroni, C; Lietava, R; Matthews, Z L; Navin, S; Palaha, A; Petrov, P; Platt, R; Šándor, L; Scott, P; Urbán, J; Villalobos Baillie, O; Tapia Takaki, J D

    2010-01-01

    In the ALICE experiment, the Low-Voltage Differential Signalling (LVDS) format is used for the transmission of trigger inputs from the detectors to the Central Trigger Processor (CTP), the L0 trigger outputs from Local Trigger Units (LTU) boards back to the detectors and the BUSY inputs from the sub-detectors to the CTP. ALICE has designed a set-up, called the LVDS transmission tester, that aims to measure various transmission quality parameters and the bit-error rate (BER) for long period runs in an automatic way. In this paper, this method is described and the conclusions from these tests for the ALICE LVDS cables are discussed

  2. LVDS tester: a systematic test of cable signal transmission at the ALICE experiment

    International Nuclear Information System (INIS)

    Barnby, L; Bhasin, A; Evans, D; Jones, G T; Jones, P G; Jovanovic, P; Jusko, A; Kour, R; Krivda, M; Lazzeroni, C; Lietava, R; Matthews, Z L; Navin, S; Palaha, A; Petrov, P; Platt, R; Scott, P; Bombara, M; Kralik, I; Sandor, L

    2010-01-01

    In the ALICE experiment, the Low-Voltage Differential Signalling (LVDS) format is used for the transmission of trigger inputs from the detectors to the Central Trigger Processor (CTP), the L0 trigger outputs from Local Trigger Units (LTU) boards back to the detectors and the BUSY inputs from the sub-detectors to the CTP. ALICE has designed a set-up, called the LVDS transmission tester, that aims to measure various transmission quality parameters and the bit-error rate (BER) for long period runs in an automatic way. In this paper, this method is described and the conclusions from these tests for the ALICE LVDS cables are discussed.

  3. Directional gear ratio transmissions

    Science.gov (United States)

    Lafever, A. E. (Inventor)

    1984-01-01

    Epicyclic gear transmissions which transmit output at a gear ratio dependent only upon the input's direction are considered. A transmission housing envelops two epicyclic gear assemblies, and has shafts extending from it. One shaft is attached to a sun gear within the first epicyclic gear assembly. Planet gears are held symmetrically about the sun gear by a planet gear carrier and are in mesh with both the sun gear and a ring gear. Two unidirectional clutches restrict rotation of the first planet gear carrier and ring gear to one direction. A connecting shaft drives a second sun gear at the same speed and direction as the first planet gear carrier while a connecting portion drives a second planet gear carrier at the same speed and direction as the first ring gear. The transmission's output is then transmitted by the second ring gear to the second shaft. Input is transmitted at a higher gear ratio and lower speed for all inputs in the first direction than in the opposite direction.

  4. Benefits of transmission interconnections

    International Nuclear Information System (INIS)

    Lyons, D.

    2006-01-01

    The benefits of new power transmission interconnections from Alberta were discussed with reference to the challenges and measures needed to move forward. Alberta's electricity system has had a long period of sustained growth in generation and demand and this trend is expected to continue. However, no new interconnections have been built since 1985 because the transmission network has not expanded in consequence with the growth in demand. As such, Alberta remains weakly interconnected with the rest of the western region. The benefits of stronger transmission interconnections include improved reliability, long-term generation capability, hydrothermal synergies, a more competitive market, system efficiencies and fuel diversity. It was noted that the more difficult challenges are not technical. Rather, the difficult challenges lie in finding an appropriate business model that recognizes different market structures. It was emphasized that additional interconnections are worthwhile and will require significant collaboration among market participants and governments. It was concluded that interties enable resource optimization between systems and their benefits far exceed their costs. tabs., figs

  5. Alternative approaches to transmission investment

    International Nuclear Information System (INIS)

    Welch, J.L.

    2004-01-01

    The International Transmission Company (ITC) is an independent power transmission company that owns, operates and maintains the high voltage transmission system in southeastern Michigan. The company's current focus is on investing in the transmission infrastructure to improve reliability, relieve congestion, improve access to generation and reduce energy costs for consumers. There is a need for investment in power transmission. Trends indicate that power transactions are on the rise while transmission investment is lagging because pricing protocols are inadequate and there is no regional tariff mechanism to allocate the benefits of new investment. The presentation reviewed the applicability of FTRs to transmission owners and the pitfalls of participant funding pricing. It also outlined the regional benefit allocation mechanism (RBAM) with an illustrative example. It was concluded that existing pricing policies must be improved to address the growing need for transmission investment. RBAM is needed to help investors recover costs from project beneficiaries. figs

  6. Laser Transmission Through Cirrus Clouds

    National Research Council Canada - National Science Library

    Liou, Kuo-Nam

    2004-01-01

    Laser transmission model development. We developed a number of 2D radiative transfer models based on the successive-order-of-scattering approach for the computation of airborne high-energy laser transmission and backscattering...

  7. Our views on transmission policy

    International Nuclear Information System (INIS)

    Wellford, W.H.; Sutley, N.H.

    1990-01-01

    In this article the authors discuss the need for predictable and fair access to transmission facilities in order to ensure competitive generation of power. They propose that the Federal Energy Regulatory Commission should regulate transmission to prevent a utility from gaining a competitive advantage in electricity generation markets, the incorporation of transmission access into every bidding program under state jurisdiction, and requirement of transmission rates, terms and conditions for all in-state utilities be included in the request for proposal

  8. 46 CFR 63.25-1 - Small automatic auxiliary boilers.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Small automatic auxiliary boilers. 63.25-1 Section 63.25... AUXILIARY BOILERS Requirements for Specific Types of Automatic Auxiliary Boilers § 63.25-1 Small automatic auxiliary boilers. Small automatic auxiliary boilers defined as having heat-input ratings of 400,000 Btu/hr...

  9. 30 CFR 77.314 - Automatic temperature control instruments.

    Science.gov (United States)

    2010-07-01

    ... UNDERGROUND COAL MINES Thermal Dryers § 77.314 Automatic temperature control instruments. (a) Automatic temperature control instruments for thermal dryer system shall be of the recording type. (b) Automatic... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic temperature control instruments. 77...

  10. Planetary Transmission Diagnostics

    Science.gov (United States)

    Lewicki, David G. (Technical Monitor); Samuel, Paul D.; Conroy, Joseph K.; Pines, Darryll J.

    2004-01-01

    This report presents a methodology for detecting and diagnosing gear faults in the planetary stage of a helicopter transmission. This diagnostic technique is based on the constrained adaptive lifting algorithm. The lifting scheme, developed by Wim Sweldens of Bell Labs, is a time domain, prediction-error realization of the wavelet transform that allows for greater flexibility in the construction of wavelet bases. Classic lifting analyzes a given signal using wavelets derived from a single fundamental basis function. A number of researchers have proposed techniques for adding adaptivity to the lifting scheme, allowing the transform to choose from a set of fundamental bases the basis that best fits the signal. This characteristic is desirable for gear diagnostics as it allows the technique to tailor itself to a specific transmission by selecting a set of wavelets that best represent vibration signals obtained while the gearbox is operating under healthy-state conditions. However, constraints on certain basis characteristics are necessary to enhance the detection of local wave-form changes caused by certain types of gear damage. The proposed methodology analyzes individual tooth-mesh waveforms from a healthy-state gearbox vibration signal that was generated using the vibration separation (synchronous signal-averaging) algorithm. Each waveform is separated into analysis domains using zeros of its slope and curvature. The bases selected in each analysis domain are chosen to minimize the prediction error, and constrained to have the same-sign local slope and curvature as the original signal. The resulting set of bases is used to analyze future-state vibration signals and the lifting prediction error is inspected. The constraints allow the transform to effectively adapt to global amplitude changes, yielding small prediction errors. However, local wave-form changes associated with certain types of gear damage are poorly adapted, causing a significant change in the

  11. Research and Transmission

    Directory of Open Access Journals (Sweden)

    Denise Pumain

    2001-01-01

    Full Text Available The present situation provides a challenge for us to reconsider the necessary link between science and pedagogy, between research and the transmission of knowledge. The Ministry of National education has just inaugurated a broad consultation of teachers on every level with a view to modernising and giving coherence to the programs of secondary education. Armand Frémont will head the group of experts responsible for history and geography. Is this a coincidence? The changeover in the jury for t...

  12. Coaxial transmission line - Equalization

    International Nuclear Information System (INIS)

    Bonnerue, J.L.; Fremont, Jacques; Haubtmann, Jack; Pillon, Gerard.

    1981-09-01

    The transmission of electrical signal through a coaxial line is not perfect and signal distortions are increased as much as the frequency spectrum is extended. We have designed and achieved passive filters (named equalizers) with transfer functions which are inverse of coaxial transfer functions. Doing so our attempt is to avoid definitive loss of information in the recorded data. The main feature of our equalization method lies in the fact it could be either an electrical or a numerical correction or both of them. Some examples in the use of this technique are also proposed [fr

  13. Economy of electric power transmission

    International Nuclear Information System (INIS)

    Manzoni, G.; Delfanti, M.

    2008-01-01

    An analysis is presented of the impact of H V and Ehv transmission costs on the final value of the kWh supplied, with reference both to transmission systems of the European type and to long distance point-to-point transmission links. The analysis is extended to A C transmission by underground cables and to Hvdc submarine and aerial links. In the European power system, the impact of transmission costs results to be usually modest, but it may become important in the case of network congestions [it

  14. A software defined RTU multi-protocol automatic adaptation data transmission method

    Science.gov (United States)

    Jin, Huiying; Xu, Xingwu; Wang, Zhanfeng; Ma, Weijun; Li, Sheng; Su, Yong; Pan, Yunpeng

    2018-02-01

    Remote terminal unit (RTU) is the core device of the monitor system in hydrology and water resources. Different devices often have different communication protocols in the application layer, which results in the difficulty in information analysis and communication networking. Therefore, we introduced the idea of software defined hardware, and abstracted the common feature of mainstream communication protocols of RTU application layer, and proposed a uniformed common protocol model. Then, various communication protocol algorithms of application layer are modularized according to the model. The executable codes of these algorithms are labeled by the virtual functions and stored in the flash chips of embedded CPU to form the protocol stack. According to the configuration commands to initialize the RTU communication systems, it is able to achieve dynamic assembling and loading of various application layer communication protocols of RTU and complete the efficient transport of sensor data from RTU to central station when the data acquisition protocol of sensors and various external communication terminals remain unchanged.

  15. Virtual Clutch Controller for Clutch-to-Clutch Shifts in Planetary-Type Automatic Transmission

    OpenAIRE

    Yunjiang Cheng; Peng Dong; Shuai Yang; Xiangyang Xu

    2015-01-01

    It is known that the shift processes of the four types of clutch-to-clutch shifts can theoretically be divided into two phases which are torque phase and inertia phase, but the execution orders are different. Two virtual clutch controllers are designed with the same eight states which include all control processes for these shifts. An equivalent method is proposed so that AT can be controlled just like DCT by adopting the torque ratios of oncoming clutch and offgoing clutch of each gear. The ...

  16. Automatic radioxenon analyzer for CTBT monitoring

    International Nuclear Information System (INIS)

    Bowyer, T.W.; Abel, K.H.; Hensley, W.K.

    1996-12-01

    Over the past 3 years, with support from US DOE's NN-20 Comprehensive Test Ban Treaty (CTBT) R ampersand D program, PNNL has developed and demonstrated a fully automatic analyzer for collecting and measuring the four Xe radionuclides, 131m Xe(11.9 d), 133m Xe(2.19 d), 133 Xe (5.24 d), and 135 Xe(9.10 h), in the atmosphere. These radionuclides are important signatures in monitoring for compliance to a CTBT. Activity ratios permit discriminating radioxenon from nuclear detonation and that from nuclear reactor operations, nuclear fuel reprocessing, or medical isotope production and usage. In the analyzer, Xe is continuously and automatically separated from the atmosphere at flow rates of about 7 m 3 /h on sorption bed. Aliquots collected for 6-12 h are automatically analyzed by electron-photon coincidence spectrometry to produce sensitivities in the range of 20-100 μBq/m 3 of air, about 100-fold better than with reported laboratory-based procedures for short time collection intervals. Spectral data are automatically analyzed and the calculated radioxenon concentrations and raw gamma- ray spectra automatically transmitted to data centers

  17. Broadband transmission EPR spectroscopy.

    Directory of Open Access Journals (Sweden)

    Wilfred R Hagen

    Full Text Available EPR spectroscopy employs a resonator operating at a single microwave frequency and phase-sensitive detection using modulation of the magnetic field. The X-band spectrometer is the general standard with a frequency in the 9-10 GHz range. Most (biomolecular EPR spectra are determined by a combination of the frequency-dependent electronic Zeeman interaction and a number of frequency-independent interactions, notably, electron spin - nuclear spin interactions and electron spin - electron spin interactions, and unambiguous analysis requires data collection at different frequencies. Extant and long-standing practice is to use a different spectrometer for each frequency. We explore the alternative of replacing the narrow-band source plus single-mode resonator with a continuously tunable microwave source plus a non-resonant coaxial transmission cell in an unmodulated external field. Our source is an arbitrary wave digital signal generator producing an amplitude-modulated sinusoidal microwave in combination with a broadband amplifier for 0.8-2.7 GHz. Theory is developed for coaxial transmission with EPR detection as a function of cell dimensions and materials. We explore examples of a doublet system, a high-spin system, and an integer-spin system. Long, straigth, helical, and helico-toroidal cells are developed and tested with dilute aqueous solutions of spin label hydroxy-tempo. A detection limit of circa 5 µM HO-tempo in water at 800 MHz is obtained for the present setup, and possibilities for future improvement are discussed.

  18. Support vector machine for automatic pain recognition

    Science.gov (United States)

    Monwar, Md Maruf; Rezaei, Siamak

    2009-02-01

    Facial expressions are a key index of emotion and the interpretation of such expressions of emotion is critical to everyday social functioning. In this paper, we present an efficient video analysis technique for recognition of a specific expression, pain, from human faces. We employ an automatic face detector which detects face from the stored video frame using skin color modeling technique. For pain recognition, location and shape features of the detected faces are computed. These features are then used as inputs to a support vector machine (SVM) for classification. We compare the results with neural network based and eigenimage based automatic pain recognition systems. The experiment results indicate that using support vector machine as classifier can certainly improve the performance of automatic pain recognition system.

  19. Automatic inference of indexing rules for MEDLINE

    Directory of Open Access Journals (Sweden)

    Shooshan Sonya E

    2008-11-01

    Full Text Available Abstract Background: Indexing is a crucial step in any information retrieval system. In MEDLINE, a widely used database of the biomedical literature, the indexing process involves the selection of Medical Subject Headings in order to describe the subject matter of articles. The need for automatic tools to assist MEDLINE indexers in this task is growing with the increasing number of publications being added to MEDLINE. Methods: In this paper, we describe the use and the customization of Inductive Logic Programming (ILP to infer indexing rules that may be used to produce automatic indexing recommendations for MEDLINE indexers. Results: Our results show that this original ILP-based approach outperforms manual rules when they exist. In addition, the use of ILP rules also improves the overall performance of the Medical Text Indexer (MTI, a system producing automatic indexing recommendations for MEDLINE. Conclusion: We expect the sets of ILP rules obtained in this experiment to be integrated into MTI.

  20. Automaticity in reading isiZulu

    Directory of Open Access Journals (Sweden)

    Sandra Land

    2016-06-01

    Full Text Available Automaticity, or instant recognition of combinations of letters as units of language, is essential for proficient reading in any language. The article explores automaticity amongst competent adult first-language readers of isiZulu, and the factors associated with it or its opposite - active decoding. Whilst the transparent spelling patterns of isiZulu aid learner readers, some of its orthographical features may militate against their gaining automaticity. These features are agglutination; a conjoined writing system; comparatively long, complex words; and a high rate of recurring strings of particular letters. This implies that optimal strategies for teaching reading in orthographically opaque languages such as English should not be assumed to apply to languages with dissimilar orthographies. Keywords: Orthography; Eye movement; Reading; isiZulu

  1. Development of fully automatic pipe welding system

    International Nuclear Information System (INIS)

    Tanioka, Shin-ichi; Nakano, Mitsuhiro; Tejima, Akio; Yamada, Minoru; Saito, Tatsuo; Saito, Yoshiyuki; Abe, Rikio

    1985-01-01

    We have succeeded in developing a fully automatic TIG welding system; namely CAPTIG that enables unmanned welding operations from the initial layer to the final finishing layer continuously. This welding system is designed for continuous, multilayered welding of thick and large diameter fixed pipes of nuclear power plants and large-size boiler plants where high-quality welding is demanded. In the tests conducted with this welding system, several hours of continuous unmanned welding corroborated that excellent beads are formed, good results are obtained in radiographic inspection and that quality welding is possible most reliably. This system incorporates a microcomputer for fully automatic controls by which it features a seam tracking function, wire feed position automatic control function, a self-checking function for inter-pass temperature, cooling water temperature and wire reserve. (author)

  2. Automatic control variac system for electronic accelerator

    International Nuclear Information System (INIS)

    Zhang Shuocheng; Wang Dan; Jing Lan; Qiao Weimin; Ma Yunhai

    2006-01-01

    An automatic control variac system is designed in order to satisfy the controlling requirement of the electronic accelerator developed by the Institute. Both design and operational principles, structure of the system as well as the software of industrial PC and micro controller unit are described. The interfaces of the control module are RS232 and RS485. A fiber optical interface (FOC) could be set up if an industrial FOC network is necessary, which will extend the filed of its application and make the communication of the system better. It is shown in practice that the system can adjust the variac output voltage automatically and assure the accurate and automatic control of the electronic accelerator. The system is designed in accordance with the general design principles and possesses the merits such as easy operation and maintenance, good expansibility, and low cost, thus it could also be used in other industrial branches. (authors)

  3. Automaticity in reading isiZulu

    Directory of Open Access Journals (Sweden)

    Sandra Land

    2016-03-01

    Full Text Available Automaticity, or instant recognition of combinations of letters as units of language, is essential for proficient reading in any language. The article explores automaticity amongst competent adult first-language readers of isiZulu, and the factors associated with it or its opposite - active decoding. Whilst the transparent spelling patterns of isiZulu aid learner readers, some of its orthographical features may militate against their gaining automaticity. These features are agglutination; a conjoined writing system; comparatively long, complex words; and a high rate of recurring strings of particular letters. This implies that optimal strategies for teaching reading in orthographically opaque languages such as English should not be assumed to apply to languages with dissimilar orthographies.Keywords: Orthography; Eye movement; Reading; isiZulu

  4. Automatic inference of indexing rules for MEDLINE.

    Science.gov (United States)

    Névéol, Aurélie; Shooshan, Sonya E; Claveau, Vincent

    2008-11-19

    Indexing is a crucial step in any information retrieval system. In MEDLINE, a widely used database of the biomedical literature, the indexing process involves the selection of Medical Subject Headings in order to describe the subject matter of articles. The need for automatic tools to assist MEDLINE indexers in this task is growing with the increasing number of publications being added to MEDLINE. In this paper, we describe the use and the customization of Inductive Logic Programming (ILP) to infer indexing rules that may be used to produce automatic indexing recommendations for MEDLINE indexers. Our results show that this original ILP-based approach outperforms manual rules when they exist. In addition, the use of ILP rules also improves the overall performance of the Medical Text Indexer (MTI), a system producing automatic indexing recommendations for MEDLINE. We expect the sets of ILP rules obtained in this experiment to be integrated into MTI.

  5. Oocytes Polar Body Detection for Automatic Enucleation

    Directory of Open Access Journals (Sweden)

    Di Chen

    2016-02-01

    Full Text Available Enucleation is a crucial step in cloning. In order to achieve automatic blind enucleation, we should detect the polar body of the oocyte automatically. The conventional polar body detection approaches have low success rate or low efficiency. We propose a polar body detection method based on machine learning in this paper. On one hand, the improved Histogram of Oriented Gradient (HOG algorithm is employed to extract features of polar body images, which will increase success rate. On the other hand, a position prediction method is put forward to narrow the search range of polar body, which will improve efficiency. Experiment results show that the success rate is 96% for various types of polar bodies. Furthermore, the method is applied to an enucleation experiment and improves the degree of automatic enucleation.

  6. The relationship between parents' and children's automatic thoughts in a college student sample.

    Science.gov (United States)

    Donnelly, Reesa; Renk, Kimberly; Sims, Valerie K; McGuire, Jack

    2011-04-01

    Research demonstrates the importance of early social interactions in the development of schemas and automatic thoughts. It does not appear, however, that the existing research examines intergenerational correlations in automatic thoughts. As a result, this study explores the relationship between the automatic thoughts of parents and those of their college-age children in a sample of 252 college students and their mothers and fathers. Results of this study suggest that there are significant relationships between parents' and college students' positive automatic thoughts. Different trends by gender also are noted in the relationships among variables for male and female college students with their mothers and fathers. Further, mothers' positive ATs predicted the positive ATs of their college students, with mothers' ratings of their own communication with their college students mediating partially this relationship. Finally, college students' anxiety and self-esteem is predicted significantly by their mothers' anxiety and self-esteem (respectively) as well as their own positive and negative ATs. These findings suggest the possibility that ATs play a role in the intergenerational transmission of certain domains of psychological functioning.

  7. Automatic emotional expression analysis from eye area

    Science.gov (United States)

    Akkoç, Betül; Arslan, Ahmet

    2015-02-01

    Eyes play an important role in expressing emotions in nonverbal communication. In the present study, emotional expression classification was performed based on the features that were automatically extracted from the eye area. Fırst, the face area and the eye area were automatically extracted from the captured image. Afterwards, the parameters to be used for the analysis through discrete wavelet transformation were obtained from the eye area. Using these parameters, emotional expression analysis was performed through artificial intelligence techniques. As the result of the experimental studies, 6 universal emotions consisting of expressions of happiness, sadness, surprise, disgust, anger and fear were classified at a success rate of 84% using artificial neural networks.

  8. Towards unifying inheritance and automatic program specialization

    DEFF Research Database (Denmark)

    Schultz, Ulrik Pagh

    2002-01-01

    and specialization of classes (inheritance) are considered different abstractions. We present a new programming language, Lapis, that unifies inheritance and program specialization at the conceptual, syntactic, and semantic levels. This paper presents the initial development of Lapis, which uses inheritance...... with covariant specialization to control the automatic application of program specialization to class members. Lapis integrates object-oriented concepts, block structure, and techniques from automatic program specialization to provide both a language where object-oriented designs can be e#ciently implemented...

  9. Automatic control system in the reactor peggy

    International Nuclear Information System (INIS)

    Bertrand, J.; Mourchon, R.; Da Costa, D.; Desandre-Navarre, Ch.

    1967-01-01

    The equipment makes it possible for the reactor to attain a given power automatically and for the power to be maintained around this level. The principle of its operation consists in the changing from one power to another, at constant period, by means of a programmer transforming a power-step request into a voltage variation which is linear with time and which represents the logarithm of the required power. The real power is compared continuously with the required power. Stabilization occurs automatically as soon as the difference between the reactor power and the required power diminishes to a few per cent. (authors) [fr

  10. Automatic incrementalization of Prolog based static analyses

    DEFF Research Database (Denmark)

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... programs and evaluated using incremental tabled evaluation, a technique for efficiently updating memo tables in response to changes in facts and rules. The approach has been implemented and integrated into the Eclipse IDE. Our measurements show that this technique is effective for automatically...

  11. Automatic identification of species with neural networks

    Directory of Open Access Journals (Sweden)

    Andrés Hernández-Serna

    2014-11-01

    Full Text Available A new automatic identification system using photographic images has been designed to recognize fish, plant, and butterfly species from Europe and South America. The automatic classification system integrates multiple image processing tools to extract the geometry, morphology, and texture of the images. Artificial neural networks (ANNs were used as the pattern recognition method. We tested a data set that included 740 species and 11,198 individuals. Our results show that the system performed with high accuracy, reaching 91.65% of true positive fish identifications, 92.87% of plants and 93.25% of butterflies. Our results highlight how the neural networks are complementary to species identification.

  12. Some results of automatic processing of images

    International Nuclear Information System (INIS)

    Golenishchev, I.A.; Gracheva, T.N.; Khardikov, S.V.

    1975-01-01

    The problems of automatic deciphering of the radiographic picture the purpose of which is making a conclusion concerning the quality of the inspected product on the basis of the product defect images in the picture are considered. The methods of defect image recognition are listed, and the algorithms and the class features of defects are described. The results of deciphering of a small radiographic picture by means of the ''Minsk-22'' computer are presented. It is established that the sensitivity of the method of the automatic deciphering is close to that obtained for visual deciphering

  13. Automatic speech recognition a deep learning approach

    CERN Document Server

    Yu, Dong

    2015-01-01

    This book summarizes the recent advancement in the field of automatic speech recognition with a focus on discriminative and hierarchical models. This will be the first automatic speech recognition book to include a comprehensive coverage of recent developments such as conditional random field and deep learning techniques. It presents insights and theoretical foundation of a series of recent models such as conditional random field, semi-Markov and hidden conditional random field, deep neural network, deep belief network, and deep stacking models for sequential learning. It also discusses practical considerations of using these models in both acoustic and language modeling for continuous speech recognition.

  14. Stress transmission in soil

    DEFF Research Database (Denmark)

    Lamandé, Mathieu; Schjønning, Per

    We urgently need increased quantitative knowledge on stress transmission in real soils loaded with agricultural machinery. 3D measurements of vertical stresses under tracked wheels were performed in situ in a Stagnic Luvisol (clay content 20 %) continuously cropped with small grain cereals......). Seven load cells were inserted horizontally from a pit with minimal disturbance of soil in each of three depths (0.3, 0.6 and 0.9 m), covering the width of the wheeled area. The position of the wheel relative to the transducers was recorded using a laser sensor. Finally, the vertical stresses near...... the soil-tyre interface were measured in separate tests by 17 stress transducers across the width of the tyres. The results showed that the inflation pressure controlled the level of maximum stresses at 0.3 m depth, while the wheel load was correlated to the measured stresses at 0.9 m depth. This supports...

  15. Information transmission strategy

    International Nuclear Information System (INIS)

    Moreau, A.

    1989-01-01

    The four propositions on which our radiation protection information transmission strategy is based are as follows: 1. Emotion exists. It rules our lives at work as well as at home, particularly when radiation safety is involved. Emotion is therefore the terrain for our strategy. 2. The basic emotion is that of fear. This must be recognized and accepted if we want to transmit objective information. The basis of our strategy is therefore listening. 3. A person cannot be divided into parts. The whole person is concerned about safety. We have to deal with that whole person. 4. To follow a strategy we need strategists. We must look at our own emotions and our own motivation before going into the field

  16. Hydatidosis: dynamics of transmission.

    Science.gov (United States)

    Bourée, P

    2001-01-01

    Hydatidosis is a widespread zoonosis infecting a large number of animals and humans. Echinococcus granulosus has the smallest taenia adult of the cestodes but with the largest larva. Its morphologic and biologic features were identified with DNA analysis. Different strains were separated according to the intermediate hosts: sheep, cattle, pigs, horses, camels. Definitive host are canids, mostly dogs, where the worm grows to adulthood in several months. The eggs are scattered in the pasture by wind and water and are ingested by various hosts. The larvae migrate through the intestinal wall and penetrate the organs, mostly liver and lungs. The eggs survive several days outside, depending on the temperature, but numerous eggs die in nature because they cannot resist desiccation and extreme temperatures. Dissemination is accomplished by dogs. In Turkana (Kenya) the incidence of hydatidosis is high because of the close relationship between the population and dogs and the habit of leaving their dead bodies in the grasslands. In rural areas, the custom of slaughtering sheep at home, among the dogs, is an important dissemination factor. The circumstances of transmission vary according to the country. In Europe the natural life cycle of E. granulosus granulosus involves dogs as the definitive host and sheep as the intermediate host. In northern Europe E. granulosus borealis infects the canids and deer. E. granulosus canadensis infects wolves and reindeer, but there are no human cases. In the endemic Mediterranean area, sheep and dromedaries are the intermediate hosts. In South America, the life cycle of E. granulosus develops among several definitive and intermediate hosts. Hence the dynamics of transmission vary according to the countries with different hosts.

  17. The Impact of Telephone Channels on the Accuracy of Automatic Speaker Recognition

    Directory of Open Access Journals (Sweden)

    V. Delić

    2011-11-01

    Full Text Available This paper presents an experimental study on the impact of telephone channels on the accuracy of automatic speaker recognition. Speaker models and the design of the recognizer used in this study are based on Hidden Markov models. In order to simulate telephonequality speech signals, several experimental conditions were introduced taking two control factors into consideration: the type of the applied codec and the probability of transmission errors. In addition, the impact of echo signals – that are often present in Internet telephony – on the accuracy of automatic speaker recognition systems is considered. Finally, the paper provides a brief overview of several methodologies for the adaptation of the recognizer to the expected environmental conditions that may enhance the robustness of the speaker recognizer.

  18. SURVEY ON PROTOTHECA SPP. OCCURRENCE IN RAW MILK FROM AUTOMATIC DISPENSER: PUBLIC HEALTH CONCERN

    Directory of Open Access Journals (Sweden)

    G. Cammi

    2011-01-01

    Full Text Available Prototheca spp. are colorless unicellular algae ubiquitous in nature and opportunistic pathogens for humans and animals. Since Prototheca is an important cause of bovine mastitis, milk, as well as dairy products, can be contaminated and represent a potential mean of transmission of this microorganism to man. We carried out a survey on the automatic milk dispensers in the Emilia-Romagna Region (Northern Italy, to evaluate human exposure to Prototheca through raw milk. Milk samples were collected from 177 automatic dispensers, distributing milk from 117 dairy herds. Prototheca spp. was isolated on 17 milk samples (9,6 % produced by 14 dairy herds. The results of molecular characterization indicate that the isolates were P. zopfii genotipe 2 e P. blaschkeae, both species being associated whit human diseases. Our investigation points out the importance of raw milk as a carrier of microorganisms potentially harmful to humans.

  19. Efficient and automatic wireless geohazard monitoring

    Science.gov (United States)

    Rubin, Marc J.

    In this dissertation, we present our research contributions geared towards creating an automated and efficient wireless sensor network (WSN) for geohazard monitoring. Specifically, this dissertation addresses three overall technical research problems inherent in implementing and deploying such a WSN, i.e., 1) automated event detection from geophysical data, 2) efficient wireless transmission, and 3) low-cost wireless hardware. In addition, after presenting algorithms, experimentation, and results from these three overall problems, we take a step back and discuss how, when, and why such scientific work matters in a geohazardous risk scenario. First, in Chapter 2, we discuss automated geohazard event detection within geophysical data. In particular, we present our pattern recognition workflow that can automatically detect snow avalanche events in seismic (geophone sensor) data. This workflow includes customized signal preprocessing for feature extraction, cluster-based stratified sub-sampling for majority class reduction, and experimentation with 12 different machine learning algorithms; results show that a decision stump classifier achieved 99.8% accuracy, 88.8% recall, and 13.2% precision in detecting avalanches within seismic data collected in the mountains above Davos, Switzerland, an improvement on previous work in the field. To address the second overall research problem (i.e., efficient wireless transmission), we present and evaluate our on-mote compressive sampling algorithm called Randomized Timing Vector (RTV) in Chapter 3 and compare our approach to four other on-mote, lossy compression algorithms in Chapter 4. Results from our work show that our RTV algorithm outperforms current on-mote compressive sampling algorithms and performs comparably to (and in many cases better than) the four state-of-the-art, on-mote lossy compression techniques. The main benefit of RTV is that it can guarantee a desired level of compression performance (and thus, radio usage

  20. Technology of optical azimuth transmission

    Science.gov (United States)

    Lu, Honggang; Hu, Chunsheng; Wang, Xingshu; Gao, Yang

    2012-11-01

    It often needs transfer a reference from one place to another place in aerospace and guided missile launching. At first, principles of several typical optical azimuth transmission methods are presented. Several typical methods are introduced, such as Theodolite (including gyro-theodolite) collimation method, Camera series method, Optical apparatus for azimuth method and polarization modulated light transmission method. For these typical azimuth transmission methods, their essential theories are elaborated. Then the devices, the application fields and limitations of these typical methods' are presented. Theodolite (including gyro-theodolite) collimation method is used in the ground assembly of spacecraft. Camera series method and optical apparatus for azimuth method are used in azimuth transmission between different decks of ship. Polarization modulated light transmission method is used in azimuth transmission of rocket and guided missile. At the last, the further developments of these methods are discussed.

  1. Recurrent-neural-network-based identification of a cascade hydraulic actuator for closed-loop automotive power transmission control

    International Nuclear Information System (INIS)

    You, Seung Han; Hahn, Jin Oh

    2012-01-01

    By virtue of its ease of operation compared with its conventional manual counterpart, automatic transmissions are commonly used as automotive power transmission control system in today's passenger cars. In accordance with this trend, research efforts on closed-loop automatic transmission controls have been extensively carried out to improve ride quality and fuel economy. State-of-the-art power transmission control algorithms may have limitations in performance because they rely on the steady-state characteristics of the hydraulic actuator rather than fully exploit its dynamic characteristics. Since the ultimate viability of closed-loop power transmission control is dominated by precise pressure control at the level of hydraulic actuator, closed-loop control can potentially attain superior efficacy in case the hydraulic actuator can be easily incorporated into model-based observer/controller design. In this paper, we propose to use a recurrent neural network (RNN) to establish a nonlinear empirical model of a cascade hydraulic actuator in a passenger car automatic transmission, which has potential to be easily incorporated in designing observers and controllers. Experimental analysis is performed to grasp key system characteristics, based on which a nonlinear system identification procedure is carried out. Extensive experimental validation of the established model suggests that it has superb one-step-ahead prediction capability over appropriate frequency range, making it an attractive approach for model-based observer/controller design applications in automotive systems

  2. Automatically predicting mood from expressed emotions

    NARCIS (Netherlands)

    Katsimerou, C.

    2016-01-01

    Affect-adaptive systems have the potential to assist users that experience systematically negative moods. This thesis aims at building a platform for predicting automatically a person’s mood from his/her visual expressions. The key word is mood, namely a relatively long-term, stable and diffused

  3. An automatic hinge system for leg orthoses

    NARCIS (Netherlands)

    Rietman, J. S.; Goudsmit, J.; Meulemans, D.; Halbertsma, J. P. K.; Geertzen, J. H. B.

    2004-01-01

    This paper describes a new automatic hinge system for leg orthoses, which provides knee stability in stance, and allows knee-flexion during swing. Indications for the hinge system are a paresis or paralysis of the quadriceps muscles. Instrumented gait analysis was performed in three patients, fitted

  4. An automatic hinge system for leg orthoses

    NARCIS (Netherlands)

    Rietman, J.S.; Goudsmit, J.; Meulemans, D.; Halbertsma, J.P.K.; Geertzen, J.H.B.

    This paper describes a new, automatic hinge system for leg orthoses, which provides knee stability in stance, and allows knee-flexion during swing. Indications for the hinge system are a paresis or paralysis of the quadriceps muscles. Instrumented gait analysis was performed in three patients,

  5. Automatic incrementalization of Prolog based static analyses

    DEFF Research Database (Denmark)

    Eichberg, Michael; Kahl, Matthias; Saha, Diptikalyan

    2007-01-01

    Modem development environments integrate various static analyses into the build process. Analyses that analyze the whole project whenever the project changes are impractical in this context. We present an approach to automatic incrementalization of analyses that are specified as tabled logic...... incrementalizing a broad range of static analyses....

  6. Automatic Estimation of Movement Statistics of People

    DEFF Research Database (Denmark)

    Ægidiussen Jensen, Thomas; Rasmussen, Henrik Anker; Moeslund, Thomas B.

    2012-01-01

    Automatic analysis of how people move about in a particular environment has a number of potential applications. However, no system has so far been able to do detection and tracking robustly. Instead, trajectories are often broken into tracklets. The key idea behind this paper is based around...

  7. Automatic program generation: future of software engineering

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, J.H.

    1979-01-01

    At this moment software development is still more of an art than an engineering discipline. Each piece of software is lovingly engineered, nurtured, and presented to the world as a tribute to the writer's skill. When will this change. When will the craftsmanship be removed and the programs be turned out like so many automobiles from an assembly line. Sooner or later it will happen: economic necessities will demand it. With the advent of cheap microcomputers and ever more powerful supercomputers doubling capacity, much more software must be produced. The choices are to double the number of programers, double the efficiency of each programer, or find a way to produce the needed software automatically. Producing software automatically is the only logical choice. How will automatic programing come about. Some of the preliminary actions which need to be done and are being done are to encourage programer plagiarism of existing software through public library mechanisms, produce well understood packages such as compiler automatically, develop languages capable of producing software as output, and learn enough about the whole process of programing to be able to automate it. Clearly, the emphasis must not be on efficiency or size, since ever larger and faster hardware is coming.

  8. Automatic Differentiation and its Program Realization

    Czech Academy of Sciences Publication Activity Database

    Hartman, J.; Lukšan, Ladislav; Zítko, J.

    2009-01-01

    Roč. 45, č. 5 (2009), s. 865-883 ISSN 0023-5954 R&D Projects: GA AV ČR IAA1030405 Institutional research plan: CEZ:AV0Z10300504 Keywords : automatic differentiation * modeling languages * systems of optimization Subject RIV: BA - General Mathematics Impact factor: 0.445, year: 2009 http://dml.cz/handle/10338.dmlcz/140037

  9. Development of automatic facilities for ZEPHYR

    International Nuclear Information System (INIS)

    Eder, O.; Lackner, E.; Pohl, F.; Schilling, H.B.

    1982-04-01

    This concept of remotely controlled facilities for repair and maintenance tasks inside the ZEPHYR vacuum vessel uses a supporting structure to insert various types of mobile automatic devices are guided by an egg-shaped disc which is part of the supporting structure. Considerations of adapting the guiding disc to the vessel contour are included. (orig.)

  10. AUTORED - the JADE automatic data reduction system

    International Nuclear Information System (INIS)

    Whittaker, J.B.

    1984-07-01

    The design and implementation of and experience with an automatic data processing system for the reduction of data from the JADE experiment at DESY is described. The central elements are a database and a job submitter which combine powerfully to minimise the need for manual intervention. (author)

  11. Automatic Assessment of 3D Modeling Exams

    Science.gov (United States)

    Sanna, A.; Lamberti, F.; Paravati, G.; Demartini, C.

    2012-01-01

    Computer-based assessment of exams provides teachers and students with two main benefits: fairness and effectiveness in the evaluation process. This paper proposes a fully automatic evaluation tool for the Graphic and Virtual Design (GVD) curriculum at the First School of Architecture of the Politecnico di Torino, Italy. In particular, the tool is…

  12. Automatic alignment of audiobooks in Afrikaans

    CSIR Research Space (South Africa)

    Van Heerden, CJ

    2012-11-01

    Full Text Available to perform Maximum A Posteriori adaptation on the baseline models. The corresponding value for models trained on the audiobook data is 0.996. An automatic measure of alignment accuracy is also introduced and compared to accuracies measured relative to a gold...

  13. Automatic Smoker Detection from Telephone Speech Signals

    DEFF Research Database (Denmark)

    Alavijeh, Amir Hossein Poorjam; Hesaraki, Soheila; Safavi, Saeid

    2017-01-01

    This paper proposes an automatic smoking habit detection from spontaneous telephone speech signals. In this method, each utterance is modeled using i-vector and non-negative factor analysis (NFA) frameworks, which yield low-dimensional representation of utterances by applying factor analysis on G...

  14. Reduction of Dutch Sentences for Automatic Subtitling

    NARCIS (Netherlands)

    Tjong Kim Sang, E.F.; Daelemans, W.; Höthker, A.

    2004-01-01

    We compare machine learning approaches for sentence length reduction for automatic generation of subtitles for deaf and hearing-impaired people with a method which relies on hand-crafted deletion rules. We describe building the necessary resources for this task: a parallel corpus of examples of news

  15. Effective speed management through automatic enforcement.

    NARCIS (Netherlands)

    Oei, H.-l.

    1994-01-01

    This paper analyses several aspects of the Dutch experience of speed enforcement, and presents the results of some speed management experiments in The Netherlands, using automatic warning of speeders and enforcement of speeding. Traditional approaches to manage speed there have not resulted in

  16. Automatic Amharic text news classification: Aneural networks ...

    African Journals Online (AJOL)

    The study is on classification of Amharic news automatically using neural networks approach. Learning Vector Quantization (LVQ) algorithm is employed to classify new instance of Amharic news based on classifier developed using training dataset. Two weighting schemes, Term Frequency (TF) and Term Frequency by ...

  17. Automatic invariant detection in dynamic web applications

    NARCIS (Netherlands)

    Groeneveld, F.; Mesbah, A.; Van Deursen, A.

    2010-01-01

    The complexity of modern web applications increases as client-side JavaScript and dynamic DOM programming are used to offer a more interactive web experience. In this paper, we focus on improving the dependability of such applications by automatically inferring invariants from the client-side and

  18. Automatization and familiarity in repeated checking

    NARCIS (Netherlands)

    Dek, E.C.P.|info:eu-repo/dai/nl/313959552; van den Hout, M.A.|info:eu-repo/dai/nl/070445354; Giele, C.L.|info:eu-repo/dai/nl/318754460; Engelhard, I.M.|info:eu-repo/dai/nl/239681533

    2015-01-01

    Repetitive, compulsive-like checking of an object leads to reductions in memory confidence, vividness, and detail. Experimental research suggests that this is caused by increased familiarity with perceptual characteristics of the stimulus and automatization of the checking procedure (Dek, van den

  19. 32 CFR 2001.30 - Automatic declassification.

    Science.gov (United States)

    2010-07-01

    ... that originated in an agency that has ceased to exist and for which there is no successor agency, the... international agreement that does not permit automatic or unilateral declassification. The declassifying agency... foreign nuclear programs (e.g., intelligence assessments or reports, foreign nuclear program information...

  20. Automatically Extracting Typical Syntactic Differences from Corpora

    NARCIS (Netherlands)

    Wiersma, Wybo; Nerbonne, John; Lauttamus, Timo

    We develop an aggregate measure of syntactic difference for automatically finding common syntactic differences between collections of text. With the use of this measure, it is possible to mine for differences between, for example, the English of learners and natives, or between related dialects. If

  1. Automatically unfair and operational requirement dismissals: Making ...

    African Journals Online (AJOL)

    This article explores the concept of the automatic unfair dismissal that is regulated in s 187(1)(c) of the Labour Relations Act 66 of 1995 (LRA), where the reason for the ... This dichotomy was dealt with by the court in Fry's Metals (Pty) Ltd v National Union of Metalworkers of SA 2003 ILJ 133 (LAC), but the decision was ...

  2. Automatic extraction of legal concepts and definitions

    NARCIS (Netherlands)

    Winkels, R.; Hoekstra, R.

    2012-01-01

    In this paper we present the results of an experiment in automatic concept and definition extraction from written sources of law using relatively simple natural language and standard semantic web technology. The software was tested on six laws from the tax domain.

  3. The CHilean Automatic Supernova sEarch

    DEFF Research Database (Denmark)

    Hamuy, M.; Pignata, G.; Maza, J.

    2012-01-01

    The CHilean Automatic Supernova sEarch (CHASE) project began in 2007 with the goal to discover young, nearby southern supernovae in order to (1) better understand the physics of exploding stars and their progenitors, and (2) refine the methods to derive extragalactic distances. During the first...

  4. AUTOMATIC IDENTIFICATION OF ITEMS IN WAREHOUSE MANAGEMENT

    OpenAIRE

    Vladimír Modrák; Peter Knuth

    2010-01-01

    Automatic identification of items saves time and is beneficial in various areas, including warehouse management. Identification can be done by many technologies, but RFID technology seems to be one of the smartest solutions. This article deals with testing and possible use of RFID technology in warehouse management. All results and measurement outcomes are documented in form of graphs followed by comprehensive analysis.

  5. Automatic Positioning System of Small Agricultural Robot

    Science.gov (United States)

    Momot, M. V.; Proskokov, A. V.; Natalchenko, A. S.; Biktimirov, A. S.

    2016-08-01

    The present article discusses automatic positioning systems of agricultural robots used in field works. The existing solutions in this area have been analyzed. The article proposes an original solution, which is easy to implement and is characterized by high- accuracy positioning.

  6. Automatic assessment of cardiac perfusion MRI

    DEFF Research Database (Denmark)

    Ólafsdóttir, Hildur; Stegmann, Mikkel Bille; Larsson, Henrik B.W.

    2004-01-01

    In this paper, a method based on Active Appearance Models (AAM) is applied for automatic registration of myocardial perfusion MRI. A semi-quantitative perfusion assessment of the registered image sequences is presented. This includes the formation of perfusion maps for three parameters; maximum up...

  7. Automatic Synthesis of Robust and Optimal Controllers

    DEFF Research Database (Denmark)

    Cassez, Franck; Jessen, Jan Jacob; Larsen, Kim Guldstrand

    2009-01-01

    In this paper, we show how to apply recent tools for the automatic synthesis of robust and near-optimal controllers for a real industrial case study. We show how to use three different classes of models and their supporting existing tools, Uppaal-TiGA for synthesis, phaver for verification...

  8. ASAM: Automatic architecture synthesis and application mapping

    DEFF Research Database (Denmark)

    Jozwiak, Lech; Lindwer, Menno; Corvino, Rosilde

    2013-01-01

    This paper focuses on mastering the automatic architecture synthesis and application mapping for heterogeneous massively-parallel MPSoCs based on customizable application-specific instruction-set processors (ASIPs). It presents an overview of the research being currently performed in the scope...

  9. Automatic arms their history, development and use

    CERN Document Server

    Johnson, Melvin M

    2015-01-01

    The evolution of automatic weapons is one of the most significant developments in weapons history. While this development has been filled with disagreements, controversy, and stray hurdles, out of all of this tumult, shouting, and shooting has come the progress in firearms from the days when it was necessary to build a fire under a gun to make it go off to the “you press the button and they do the work" automatic firearms of the present day. In 1941, Melvin M. Johnson Jr. and Charles T. Haven, both well-established experts on firearms and ammunitions in their day, commemorated this development in Automatic Arms: Their History, Development and Use. The topics on which they illuminate the reader include: History and development How they work How to keep them firing How they may be employed in combat In the authors' foreword, they state, “There has been a great deal of general discussion about various automatic weapons pro and con, and naturally there have been misunderstandings and misinterpretations." They s...

  10. Automatic Water Sensor Window Opening System

    KAUST Repository

    Percher, Michael

    2013-12-05

    A system can automatically open at least one window of a vehicle when the vehicle is being submerged in water. The system can include a water collector and a water sensor, and when the water sensor detects water in the water collector, at least one window of the vehicle opens.

  11. Automatic TLI recognition system, general description

    Energy Technology Data Exchange (ETDEWEB)

    Lassahn, G.D.

    1997-02-01

    This report is a general description of an automatic target recognition system developed at the Idaho National Engineering Laboratory for the Department of Energy. A user`s manual is a separate volume, Automatic TLI Recognition System, User`s Guide, and a programmer`s manual is Automatic TLI Recognition System, Programmer`s Guide. This system was designed as an automatic target recognition system for fast screening of large amounts of multi-sensor image data, based on low-cost parallel processors. This system naturally incorporates image data fusion, and it gives uncertainty estimates. It is relatively low cost, compact, and transportable. The software is easily enhanced to expand the system`s capabilities, and the hardware is easily expandable to increase the system`s speed. In addition to its primary function as a trainable target recognition system, this is also a versatile, general-purpose tool for image manipulation and analysis, which can be either keyboard-driven or script-driven. This report includes descriptions of three variants of the computer hardware, a description of the mathematical basis if the training process, and a description with examples of the system capabilities.

  12. Applications of automatic differentiation in topology optimization

    DEFF Research Database (Denmark)

    Nørgaard, Sebastian A.; Sagebaum, Max; Gauger, Nicolas R.

    2017-01-01

    and is demonstrated on two separate, previously published types of problems in topology optimization. Two separate software packages for automatic differentiation, CoDiPack and Tapenade are considered, and their performance and usability trade-offs are discussed and compared to a hand coded adjoint gradient...

  13. Automatic prejudice in childhood and early adolescence

    NARCIS (Netherlands)

    Degner, J.; Wentura, D.

    2010-01-01

    Four cross-sectional studies are presented that investigated the automatic activation of prejudice in children and adolescents (aged 9 years to 15 years). Therefore, 4 different versions of the affective priming task were used, with pictures of ingroup and outgroup members being presented as

  14. Automatic coding method of the ACR Code

    International Nuclear Information System (INIS)

    Park, Kwi Ae; Ihm, Jong Sool; Ahn, Woo Hyun; Baik, Seung Kook; Choi, Han Yong; Kim, Bong Gi

    1993-01-01

    The authors developed a computer program for automatic coding of ACR(American College of Radiology) code. The automatic coding of the ACR code is essential for computerization of the data in the department of radiology. This program was written in foxbase language and has been used for automatic coding of diagnosis in the Department of Radiology, Wallace Memorial Baptist since May 1992. The ACR dictionary files consisted of 11 files, one for the organ code and the others for the pathology code. The organ code was obtained by typing organ name or code number itself among the upper and lower level codes of the selected one that were simultaneous displayed on the screen. According to the first number of the selected organ code, the corresponding pathology code file was chosen automatically. By the similar fashion of organ code selection, the proper pathologic dode was obtained. An example of obtained ACR code is '131.3661'. This procedure was reproducible regardless of the number of fields of data. Because this program was written in 'User's Defined Function' from, decoding of the stored ACR code was achieved by this same program and incorporation of this program into program in to another data processing was possible. This program had merits of simple operation, accurate and detail coding, and easy adjustment for another program. Therefore, this program can be used for automation of routine work in the department of radiology

  15. Automatic Radiometric Normalization of Multitemporal Satellite Imagery

    DEFF Research Database (Denmark)

    Canty, Morton J.; Nielsen, Allan Aasbjerg; Schmidt, Michael

    2004-01-01

    The linear scale invariance of the multivariate alteration detection (MAD) transformation is used to obtain invariant pixels for automatic relative radiometric normalization of time series of multispectral data. Normalization by means of ordinary least squares regression method is compared with n...

  16. Automatically extracting class diagrams from spreadsheets

    NARCIS (Netherlands)

    Hermans, F.; Pinzger, M.; Van Deursen, A.

    2010-01-01

    The use of spreadsheets to capture information is widespread in industry. Spreadsheets can thus be a wealthy source of domain information. We propose to automatically extract this information and transform it into class diagrams. The resulting class diagram can be used by software engineers to

  17. Automatic characterization of dynamics in Absence Epilepsy

    DEFF Research Database (Denmark)

    Petersen, Katrine N. H.; Nielsen, Trine N.; Kjær, Troels W.

    2013-01-01

    Dynamics of the spike-wave paroxysms in Childhood Absence Epilepsy (CAE) are automatically characterized using novel approaches. Features are extracted from scalograms formed by Continuous Wavelet Transform (CWT). Detection algorithms are designed to identify an estimate of the temporal development...

  18. Evaluating automatically annotated treebanks for linguistic research

    NARCIS (Netherlands)

    Bloem, J.; Bański, P.; Kupietz, M.; Lüngen, H.; Witt, A.; Barbaresi, A.; Biber, H.; Breiteneder, E.; Clematide, S.

    2016-01-01

    This study discusses evaluation methods for linguists to use when employing an automatically annotated treebank as a source of linguistic evidence. While treebanks are usually evaluated with a general measure over all the data, linguistic studies often focus on a particular construction or a group

  19. Performance evaluation of automatic voltage regulators ...

    African Journals Online (AJOL)

    Performance of various Automatic Voltage Regulators (AVR's) in Nigeria and the causes of their inability to regulate at their set points have been investigated. The result indicates that the imported AVRs fail to give the 220 volts as displayed on the name plate at the specified low set point (such as 100, 120 volts etc) on ...

  20. Automatic Subspace Learning via Principal Coefficients Embedding.

    Science.gov (United States)

    Peng, Xi; Lu, Jiwen; Yi, Zhang; Yan, Rui

    2017-11-01

    In this paper, we address two challenging problems in unsupervised subspace learning: 1) how to automatically identify the feature dimension of the learned subspace (i.e., automatic subspace learning) and 2) how to learn the underlying subspace in the presence of Gaussian noise (i.e., robust subspace learning). We show that these two problems can be simultaneously solved by proposing a new method [(called principal coefficients embedding (PCE)]. For a given data set , PCE recovers a clean data set from and simultaneously learns a global reconstruction relation of . By preserving into an -dimensional space, the proposed method obtains a projection matrix that can capture the latent manifold structure of , where is automatically determined by the rank of with theoretical guarantees. PCE has three advantages: 1) it can automatically determine the feature dimension even though data are sampled from a union of multiple linear subspaces in presence of the Gaussian noise; 2) although the objective function of PCE only considers the Gaussian noise, experimental results show that it is robust to the non-Gaussian noise (e.g., random pixel corruption) and real disguises; and 3) our method has a closed-form solution and can be calculated very fast. Extensive experimental results show the superiority of PCE on a range of databases with respect to the classification accuracy, robustness, and efficiency.

  1. New Intelligent Transmission Concept for Hybrid Mobile Robot Speed Control

    Directory of Open Access Journals (Sweden)

    Nazim Mir-Nasiri

    2005-09-01

    Full Text Available This paper presents a new concept of a mobile robot speed control by using two degree of freedom gear transmission. The developed intelligent speed controller utilizes a gear box which comprises of epicyclic gear train with two inputs, one coupled with the engine shaft and another with the shaft of a variable speed dc motor. The net output speed is a combination of the two input speeds and is governed by the transmission ratio of the planetary gear train. This new approach eliminates the use of a torque converter which is otherwise an indispensable part of all available automatic transmissions, thereby reducing the power loss that occurs in the box during the fluid coupling. By gradually varying the speed of the dc motor a stepless transmission has been achieved. The other advantages of the developed controller are pulling over and reversing the vehicle, implemented by intelligent mixing of the dc motor and engine speeds. This approach eliminates traditional braking system in entire vehicle design. The use of two power sources, IC engine and battery driven DC motor, utilizes the modern idea of hybrid vehicles. The new mobile robot speed controller is capable of driving the vehicle even in extreme case of IC engine failure, for example, due to gas depletion.

  2. New Intelligent Transmission Concept for Hybrid Mobile Robot Speed Control

    Directory of Open Access Journals (Sweden)

    Nazim Mir-Nasiri

    2008-11-01

    Full Text Available This paper presents a new concept of a mobile robot speed control by using two degree of freedom gear transmission. The developed intelligent speed controller utilizes a gear box which comprises of epicyclic gear train with two inputs, one coupled with the engine shaft and another with the shaft of a variable speed dc motor. The net output speed is a combination of the two input speeds and is governed by the transmission ratio of the planetary gear train. This new approach eliminates the use of a torque converter which is otherwise an indispensable part of all available automatic transmissions, thereby reducing the power loss that occurs in the box during the fluid coupling. By gradually varying the speed of the dc motor a stepless transmission has been achieved. The other advantages of the developed controller are pulling over and reversing the vehicle, implemented by intelligent mixing of the dc motor and engine speeds. This approach eliminates traditional braking system in entire vehicle design. The use of two power sources, IC engine and battery driven DC motor, utilizes the modern idea of hybrid vehicles. The new mobile robot speed controller is capable of driving the vehicle even in extreme case of IC engine failure, for example, due to gas depletion..

  3. Automatic River Network Extraction from LIDAR Data

    Science.gov (United States)

    Maderal, E. N.; Valcarcel, N.; Delgado, J.; Sevilla, C.; Ojeda, J. C.

    2016-06-01

    National Geographic Institute of Spain (IGN-ES) has launched a new production system for automatic river network extraction for the Geospatial Reference Information (GRI) within hydrography theme. The goal is to get an accurate and updated river network, automatically extracted as possible. For this, IGN-ES has full LiDAR coverage for the whole Spanish territory with a density of 0.5 points per square meter. To implement this work, it has been validated the technical feasibility, developed a methodology to automate each production phase: hydrological terrain models generation with 2 meter grid size and river network extraction combining hydrographic criteria (topographic network) and hydrological criteria (flow accumulation river network), and finally the production was launched. The key points of this work has been managing a big data environment, more than 160,000 Lidar data files, the infrastructure to store (up to 40 Tb between results and intermediate files), and process; using local virtualization and the Amazon Web Service (AWS), which allowed to obtain this automatic production within 6 months, it also has been important the software stability (TerraScan-TerraSolid, GlobalMapper-Blue Marble , FME-Safe, ArcGIS-Esri) and finally, the human resources managing. The results of this production has been an accurate automatic river network extraction for the whole country with a significant improvement for the altimetric component of the 3D linear vector. This article presents the technical feasibility, the production methodology, the automatic river network extraction production and its advantages over traditional vector extraction systems.

  4. AUTOMATIC RIVER NETWORK EXTRACTION FROM LIDAR DATA

    Directory of Open Access Journals (Sweden)

    E. N. Maderal

    2016-06-01

    Full Text Available National Geographic Institute of Spain (IGN-ES has launched a new production system for automatic river network extraction for the Geospatial Reference Information (GRI within hydrography theme. The goal is to get an accurate and updated river network, automatically extracted as possible. For this, IGN-ES has full LiDAR coverage for the whole Spanish territory with a density of 0.5 points per square meter. To implement this work, it has been validated the technical feasibility, developed a methodology to automate each production phase: hydrological terrain models generation with 2 meter grid size and river network extraction combining hydrographic criteria (topographic network and hydrological criteria (flow accumulation river network, and finally the production was launched. The key points of this work has been managing a big data environment, more than 160,000 Lidar data files, the infrastructure to store (up to 40 Tb between results and intermediate files, and process; using local virtualization and the Amazon Web Service (AWS, which allowed to obtain this automatic production within 6 months, it also has been important the software stability (TerraScan-TerraSolid, GlobalMapper-Blue Marble , FME-Safe, ArcGIS-Esri and finally, the human resources managing. The results of this production has been an accurate automatic river network extraction for the whole country with a significant improvement for the altimetric component of the 3D linear vector. This article presents the technical feasibility, the production methodology, the automatic river network extraction production and its advantages over traditional vector extraction systems.

  5. Transmissible spongiform encephalopathies.

    Science.gov (United States)

    Liemann, S; Glockshuber, R

    1998-09-18

    Scrapie, bovine spongiform encephalopathy (BSE), and the Creutzfeldt-Jakob disease (CJD) belong to a group of lethal neurodegenerative disorders in mammals. Prion diseases or transmissible spongiform encephalopathies (TSEs) are characterized by the accumulation of an abnormal isoform (PrPSc) of the host-encoded cellular prion protein (PrPC) in the brain. The infectious agent, the 'prion,' is believed to be devoid of informational nucleic acid and to consist largely, if not entirely, of PrPSc. The PrP isoforms contain identical amino acid sequences yet differ in their overall secondary structure with the PrPSc isoform possessing a higher beta-sheet and lower alpha-helix content than PrPC. Elucidation of the three-dimensional structure of PrPC has provided important clues on the molecular basis of inherited human TSEs and on the species barrier phenomenon of TSEs. Nevertheless, the molecular mechanism of the conformational rearrangement of PrPC into PrPSc is still unknown, mainly due to the lack of detailed structural information on PrPSc. Within the framework of the 'protein only' hypothesis, two plausible models for the self-replication of prions have been suggested, the conformational model and the nucleation-dependent polymerization model.

  6. Application of semi-active RFID power meter in automatic verification pipeline and intelligent storage system

    Science.gov (United States)

    Chen, Xiangqun; Huang, Rui; Shen, Liman; chen, Hao; Xiong, Dezhi; Xiao, Xiangqi; Liu, Mouhai; Xu, Renheng

    2018-03-01

    In this paper, the semi-active RFID watt-hour meter is applied to automatic test lines and intelligent warehouse management, from the transmission system, test system and auxiliary system, monitoring system, realize the scheduling of watt-hour meter, binding, control and data exchange, and other functions, make its more accurate positioning, high efficiency of management, update the data quickly, all the information at a glance. Effectively improve the quality, efficiency and automation of verification, and realize more efficient data management and warehouse management.

  7. Hendra virus ecology and transmission.

    Science.gov (United States)

    Field, Hume E

    2016-02-01

    Hendra virus causes acute and highly fatal infection in horses and humans. Pteropid bats (flying-foxes) are the natural host of the virus, with age and species being risk factors for infection. Urine is the primary route of excretion in flying-foxes, with viral RNA more frequently detected in Pteropus alecto and P. conspicillatus than other species. Infection prevalence in flying-foxes can vary between and within years, with a winter peak of excretion occurring in some regions. Vertical transmission and recrudescing infection has been reported in flying-foxes, but horizontal transmission is evidently the primary mode of transmission. The most parsimonious mode of flying-fox to horse transmission is equine contact (oro-nasal, conjunctival) with infected flying-fox urine, either directly, or via urine-contaminated pasture or surfaces. Horse to horse transmission is inefficient, requiring direct contact with infected body fluids. Flying-fox to human transmission has not been recorded; all human cases have been associated with close and direct contact with infected horses. Canine cases (subclinical) have also been limited to equine case properties. Notwithstanding the recent availability of an effective vaccine for horses, a comprehensive understanding of Hendra virus ecology and transmission is essential to limit inter-species transmission. Copyright © 2016 Elsevier B.V. All rights reserved.

  8. Endoscopic transmission of Helicobacter pylori

    NARCIS (Netherlands)

    Tytgat, G. N.

    1995-01-01

    The contamination of endoscopes and biopsy forceps with Helicobacter pylori occurs readily after endoscopic examination of H. pylori-positive patients. Unequivocal proof of iatrogenic transmission of the organism has been provided. Estimates for transmission frequency approximate to 4 per 1000

  9. Transmission reliability faces future challenges

    International Nuclear Information System (INIS)

    Beaty, W.

    1993-01-01

    The recently published Washington International Energy Group's 1993 Electric Utility Outlook states that nearly one-third (31 percent) of U.S. utility executives expect reliability to decrease in the near future. Electric power system stability is crucial to reliability. Stability analysis determines whether a system will stay intact under normal operating conditions, during minor disturbances such as load fluctuations, and during major disturbances when one or more parts of the system fails. All system elements contribute to reliability or the lack of it. However, this report centers on the transmission segment of the electric system. The North American Electric Reliability Council (NERC) says the transmission systems as planned will be adequate over the next 10 years. However, delays in building new lines and increasing demands for transmission services are serious concerns. Reliability concerns exist in the Mid-Continent Area Power Pool and the Mid-America Interconnected Network regions where transmission facilities have not been allowed to be constructed as planned. Portions of the transmission systems in other regions are loaded at or near their limits. NERC further states that utilities must be allowed to complete planned generation and transmission as scheduled. A reliable supply of electricity also depends on adhering to established operating criteria. Factors that could complicate operations include: More interchange schedules resulting from increased transmission services. Increased line loadings in portions of the transmission systems. Proliferation of non-utility generators

  10. HVDC power transmission technology assessment

    Energy Technology Data Exchange (ETDEWEB)

    Hauth, R.L.; Tatro, P.J.; Railing, B.D. [New England Power Service Co., Westborough, MA (United States); Johnson, B.K.; Stewart, J.R. [Power Technologies, Inc., Schenectady, NY (United States); Fink, J.L.

    1997-04-01

    The purpose of this study was to develop an assessment of the national utility system`s needs for electric transmission during the period 1995-2020 that could be met by future reduced-cost HVDC systems. The assessment was to include an economic evaluation of HVDC as a means for meeting those needs as well as a comparison with competing technologies such as ac transmission with and without Flexible AC Transmission System (FACTS) controllers. The role of force commutated dc converters was to be assumed where appropriate. The assessment begins by identifying the general needs for transmission in the U.S. in the context of a future deregulated power industry. The possible roles for direct current transmission are then postulated in terms of representative scenarios. A few of the scenarios are illustrated with the help of actual U.S. system examples. non-traditional applications as well as traditional applications such as long lines and asynchronous interconnections are discussed. The classical ``break-even distance`` concept for comparing HVDC and ac lines is used to assess the selected scenarios. The impact of reduced-cost converters is reflected in terms of the break-even distance. This report presents a comprehensive review of the functional benefits of HVDC transmission and updated cost data for both ac and dc system components. It also provides some provocative thoughts on how direct current transmission might be applied to better utilize and expand our nation`s increasingly stressed transmission assets.

  11. Continuously variable transmission (CVT) with ceramic components

    Energy Technology Data Exchange (ETDEWEB)

    Albers, A.; Stuffer, A.; Bernhardt, J. [Universitaet Karlsruhe (T.H.), IPEK Institut fuer Produktentwicklung, Kaiserstr. 10, 76131 Karlsruhe (Germany)

    2005-03-01

    Continuously Variable Transmissions (CVTs) are a powerful alternative to automatic gearboxes for passenger cars. Some of these CVTs transmit the power via traction forces through highly loaded lubricated contacts. The aim of the presented work is to increase the capability of this system by means of appropriate engineering ceramics. The modifications are investigated on a machine element test bench. The necessary new tools for the design process and the configuration of the test bench are presented. Measurements show that the desired improvements can be achieved by using engineering ceramics but lifetime requirements have not been met yet. (Abstract Copyright [2005], Wiley Periodicals, Inc.) [German] Stufenlos verstellbare Getriebe sind eine leistungsfaehige Alternative zu konventionellen Stufenautomaten in Kraftfahrzeugen. Die Leistung wird bei einigen dieser stufenlosen Getriebe reibschluessig ueber hoch belastete geschmierte Friktionswirkflaechen uebertragen. Die vorgestellten Arbeiten haben das Ziel, durch den Einsatz von geeigneten Ingenieurkeramiken die Leistungsfaehigkeit des Systems weiter zu steigern. Die Modifikationen werden an einem Bauteilpruefstand untersucht. Es werden die Werkzeuge fuer den Systemdesignprozess und der Aufbau des Pruefstands vorgestellt. Messergebnisse zeigen, dass mit der eingesetzten Ingenieurkeramik die gewuenschten Verbesserungen erzielt werden koennen, die Lebensdaueraspekte werden jedoch noch nicht erfuellt. (Abstract Copyright [2005], Wiley Periodicals, Inc.)

  12. National automatic network of environmental radiological monitoring (RENAMORA)

    International Nuclear Information System (INIS)

    Gonzalez M, J.L.; Sanchez H, L.

    2003-01-01

    Inside the programs of Environmental Radiological Surveillance that it carries out the National Commission of Nuclear Security and Safeguards (CNSNS), it develops an National Automatic Network of Environmental Radiological Monitoring (RENAMORA), where it is carried out a registration of speed of environmental dose in continuous and simultaneous forms with the same moment of the measurement. This net allows to account with the meticulous and opportune information that will help to characterize, in dynamics form, the radiological conditions of diverse geographical zones of the country, including the sites that by normative require bigger surveillance, like its are the Laguna Verde Nuclear power station (CNLV), the Nuclear Center of Mexico (ININ) and the Radioactive waste storage center (CADER). This net is in its first development stage; three points inside the state of Veracruz, in the surroundings of the CNLV, already its are operating; the obtained data of rapidity of environmental dose are being stored in a database inside a primary data center located in the facilities of the CNSNS in Mexico city and its will be analyzed according to the project advances. At the moment, its are installing the first ten teams corresponding to the first phase of the RENAMORA (three stages); its are carried out operation tests, transmission, reception and administration of data. The obtained data will be interpreted, analyzed and inter compared to evaluate the risk levels to that it would be hold the population and to determine thresholds that allow to integrate the alarm systems that its had considered for emergency situations. (Author)

  13. Energy Transmission and Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Mathison, Jane

    2012-12-31

    The objective of Energy Transmission and Infrastructure Northern Ohio (OH) was to lay the conceptual and analytical foundation for an energy economy in northern Ohio that will: • improve the efficiency with which energy is used in the residential, commercial, industrial, agricultural, and transportation sectors for Oberlin, Ohio as a district-wide model for Congressional District OH-09; • identify the potential to deploy wind and solar technologies and the most effective configuration for the regional energy system (i.e., the ratio of distributed or centralized power generation); • analyze the potential within the district to utilize farm wastes to produce biofuels; • enhance long-term energy security by identifying ways to deploy local resources and building Ohio-based enterprises; • identify the policy, regulatory, and financial barriers impeding development of a new energy system; and • improve energy infrastructure within Congressional District OH-09. This objective of laying the foundation for a renewable energy system in Ohio was achieved through four primary areas of activity: 1. district-wide energy infrastructure assessments and alternative-energy transmission studies; 2. energy infrastructure improvement projects undertaken by American Municipal Power (AMP) affiliates in the northern Ohio communities of Elmore, Oak Harbor, and Wellington; 3. Oberlin, OH-area energy assessment initiatives; and 4. a district-wide conference held in September 2011 to disseminate year-one findings. The grant supported 17 research studies by leading energy, policy, and financial specialists, including studies on: current energy use in the district and the Oberlin area; regional potential for energy generation from renewable sources such as solar power, wind, and farm-waste; energy and transportation strategies for transitioning the City of Oberlin entirely to renewable resources and considering pedestrians, bicyclists, and public transportation as well as drivers

  14. Multi-order, automatic dispersion compensation for 1.28 Terabaud signals

    Science.gov (United States)

    Paquot, Yvan; Schröder, Jochen; Van Erps, Jürgen; Vo, Trung D.; Pelusi, Mark D.; Madden, Steve; Luther-Davies, Barry; Eggleton, Benjamin J.

    2012-06-01

    Transmitting ultra-high symbol rate optical signals remains a challenge due to their high sensitivity to fluctuations of GVD and higher orders of dispersion in the transmission link. Being able to cancel the impairments due to those fluctuations is a key requirement to make transmission of ultrashort optical pulses practical. We demonstrate an automatic compensation scheme able to keep an Optical Time Division Multiplexed (OTDM) signal stable at a bandwidth of up to 1.28 Tbaud in spite of external perturbations. Our approach is based on monitoring the signal with a photonic-chip-based all-optical RF-spectrum analyzer. The measurement of a single parameter extracted from the RF-spectrum is used to drive a multidimensional optimization algorithm. We apply the method to the real time simultaneous compensation for 2nd, 3rd and 4th order dispersion using an LCOS spectral pulse shaper (SPS) as a tunable dispersion compensator.

  15. 30 CFR 57.19006 - Automatic hoist braking devices.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic hoist braking devices. 57.19006 Section 57.19006 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoists § 57.19006 Automatic hoist braking devices. Automatic hoists shall be provided with devices...

  16. 30 CFR 56.19006 - Automatic hoist braking devices.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic hoist braking devices. 56.19006 Section 56.19006 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Hoisting Hoists § 56.19006 Automatic hoist braking devices. Automatic hoists shall be provided with devices...

  17. The ‘Continuing Misfortune’ of Automatism in Early Surrealism

    Directory of Open Access Journals (Sweden)

    Tessel M. Bauduin

    2015-09-01

    Full Text Available In the 1924 Manifesto of Surrealism surrealist leader André Breton (1896-1966 defined Surrealism as ‘psychic automatism in its pure state,’ positioning ‘psychic automatism’ as both a concept and a technique. This definition followed upon an intense period of experimentation with various forms of automatism among the proto-surrealist group; predominantly automatic writing, but also induced dream states. This article explores how surrealist ‘psychic automatism’ functioned as a mechanism for communication, or the expression of thought as directly as possible through the unconscious, in the first two decades of Surrealism. It touches upon automatic writing, hysteria as an automatic bodily performance of the unconscious, dreaming and the experimentation with induced dream states, and automatic drawing and other visual arts-techniques that could be executed more or less automatically as well. For all that the surrealists reinvented automatism for their own poetic, artistic and revolutionary aims, the automatic techniques were primarily drawn from contemporary Spiritualism, psychical research and experimentation with mediums, and the article teases out the connections to mediumistic automatism. It is demonstrated how the surrealists effectively and successfully divested automatism of all things spiritual. It furthermore becomes clear that despite various mishaps, automatism in many forms was a very successful creative technique within Surrealism.

  18. Automaticity of walking: functional significance, mechanisms, measurement and rehabilitation strategies

    Directory of Open Access Journals (Sweden)

    David J Clark

    2015-05-01

    Full Text Available Automaticity is a hallmark feature of walking in adults who are healthy and well-functioning. In the context of walking, ‘automaticity’ refers to the ability of the nervous system to successfully control typical steady state walking with minimal use of attention-demanding executive control resources. Converging lines of evidence indicate that walking deficits and disorders are characterized in part by a shift in the locomotor control strategy from healthy automaticity to compensatory executive control. This is potentially detrimental to walking performance, as an executive control strategy is not optimized for locomotor control. Furthermore, it places excessive demands on a limited pool of executive reserves. The result is compromised ability to perform basic and complex walking tasks and heightened risk for adverse mobility outcomes including falls. Strategies for rehabilitation of automaticity are not well defined, which is due to both a lack of systematic research into the causes of impaired automaticity and to a lack of robust neurophysiological assessments by which to gauge automaticity. These gaps in knowledge are concerning given the serious functional implications of compromised automaticity. Therefore, the objective of this article is to advance the science of automaticity of walking by consolidating evidence and identifying gaps in knowledge regarding: a functional significance of automaticity; b neurophysiology of automaticity; c measurement of automaticity; d mechanistic factors that compromise automaticity; and e strategies for rehabilitation of automaticity.

  19. 46 CFR 171.118 - Automatic ventilators and side ports.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 7 2010-10-01 2010-10-01 false Automatic ventilators and side ports. 171.118 Section 171.118 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY... Bulkhead or Weather Deck § 171.118 Automatic ventilators and side ports. (a) An automatic ventilator must...

  20. 30 CFR 75.1404 - Automatic brakes; speed reduction gear.

    Science.gov (United States)

    2010-07-01

    ... Automatic brakes; speed reduction gear. [Statutory Provisions] Each locomotive and haulage car used in an... permit automatic brakes, locomotives and haulage cars shall be subject to speed reduction gear, or other... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic brakes; speed reduction gear. 75.1404...

  1. 49 CFR 236.825 - System, automatic train control.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 4 2010-10-01 2010-10-01 false System, automatic train control. 236.825 Section..., INSPECTION, MAINTENANCE, AND REPAIR OF SIGNAL AND TRAIN CONTROL SYSTEMS, DEVICES, AND APPLIANCES Definitions § 236.825 System, automatic train control. A system so arranged that its operation will automatically...

  2. Word Processing in Dyslexics: An Automatic Decoding Deficit?

    Science.gov (United States)

    Yap, Regina; Van Der Leu, Aryan

    1993-01-01

    Compares dyslexic children with normal readers on measures of phonological decoding and automatic word processing. Finds that dyslexics have a deficit in automatic phonological decoding skills. Discusses results within the framework of the phonological deficit and the automatization deficit hypotheses. (RS)

  3. 30 CFR 75.1403-4 - Criteria-Automatic elevators.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Criteria-Automatic elevators. 75.1403-4 Section... Criteria—Automatic elevators. (a) The doors of automatic elevators should be equipped with interlocking switches so arranged that the elevator car will be immovable while any door is opened or unlocked, and...

  4. 30 CFR 77.1401 - Automatic controls and brakes.

    Science.gov (United States)

    2010-07-01

    ... MINES Personnel Hoisting § 77.1401 Automatic controls and brakes. Hoists and elevators shall be equipped with overspeed, overwind, and automatic stop controls and with brakes capable of stopping the elevator... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Automatic controls and brakes. 77.1401 Section...

  5. 21 CFR 211.68 - Automatic, mechanical, and electronic equipment.

    Science.gov (United States)

    2010-04-01

    ... SERVICES (CONTINUED) DRUGS: GENERAL CURRENT GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS Equipment § 211.68 Automatic, mechanical, and electronic equipment. (a) Automatic, mechanical, or electronic... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Automatic, mechanical, and electronic equipment...

  6. Renewable Resource Integration Project - Scoping Study of Strategic Transmission, Operations, and Reliability Issues

    Energy Technology Data Exchange (ETDEWEB)

    Eto, Joseph; Budhraja, Vikram; Ballance, John; Dyer, Jim; Mobasheri, Fred; Eto, Joseph

    2008-07-01

    California is on a path to increase utilization of renewable resources. California will need to integrate approximately 30,000 megawatts (MW) of new renewable generation in the next 20 years. Renewable resources are typically located in remote locations, not near the load centers. Nearly two/thirds or 20,000 MW of new renewable resources needed are likely to be delivered to Los Angeles Basin transmission gateways. Integration of renewable resources requires interconnection to the power grid, expansion of the transmission system capability between the backbone power grid and transmission gateways, and increase in delivery capacity from transmission gateways to the local load centers. To scope the transmission, operations, and reliability issues for renewables integration, this research focused on the Los Angeles Basin Area transmission gateways where most of new renewables are likely. Necessary actions for successful renewables integration include: (1) Expand Los Angeles Basin Area transmission gateway and nomogram limits by 10,000 to 20,000 MW; (2) Upgrade local transmission network for deliverability to load centers; (3) Secure additional storage, demand management, automatic load control, dynamic pricing, and other resources that meet regulation and ramping needed in real time operations; (4) Enhance local voltage support; and (5) Expand deliverability from Los Angeles to San Diego and Northern California.

  7. On automatic visual inspection of reflective surfaces

    DEFF Research Database (Denmark)

    Kulmann, Lionel

    1995-01-01

    lighting methods in a framework, general usable for inspecting reflective surfaces. Special attention has been given to the design of illumination techniques to enhance defects of highly reflective aluminum sheets. The chosen optical system setup has been used to enhance surface defects of other reflective......This thesis descrbes different methods to perform automatic visual inspection of reflective manufactured products, with the aim of increasing productivity, reduce cost and improve the quality level of the production. We investigate two different systems performing automatic visual inspection....... The first is the inspection of highly reflective aluminum sheets, used by the Danish company Bang & Olufsen, as a part of the exterior design and general appearance of their audio and video products. The second is the inspection of IBM hard disk read/write heads for defects during manufacturing. We have...

  8. Research and implementation of software automatic test

    Science.gov (United States)

    Li-hong, LIAN

    2017-06-01

    With the fast development in IT technology nowadays, software is increasingly complex and large. Hundreds of people in the development team, thousands of modules and interfaces, across geographies and systems user are no longer a fresh thing. All of these put forward higher requirements for software testing. Due to the low cost of implementation and the advantage of effective inheritance and accumulation of test assets, software automation testing has gradually become one of the important means to ensure the quality of software for IT enterprises. This paper analyzes the advantages of automatic test, common misconceptions; puts forward unsuitable application scenarios and the best time to intervene; focus on the analysis of the feasibility of judging the interface automation test; and puts forward the function and elements of interface automatic test tools to have; provides a reference for large-scale project interface automated testing tool selection or custom development.

  9. Automatic classification of graphite in cast iron.

    Science.gov (United States)

    Gomes, Otávio da F M; Paciornik, Sidnei

    2005-08-01

    A method for automatic classification of the shape of graphite particles in cast iron is proposed. In a typical supervised classification procedure, the standard charts from the ISO-945 standard are used as a training and validation population. Several shape and size parameters are described and used as discriminants. A new parameter, the average internal angle, is proposed and is shown to be relevant for accurate classification. The ideal parameter sets are determined, leading to validation success rates above 90%. The classifier is then applied to real cast iron samples and provides results that are consistent with visual examination. The method provides classification results per particle, different from the traditional per field chart comparison methods. The full procedure can run automatically without user interference.

  10. Automatic tuning of free electron lasers

    International Nuclear Information System (INIS)

    Agapov, Ilya; Zagorodnov, Igor; Geloni, Gianluca; Tomin, Sergey

    2017-01-01

    Existing FEL facilities often suffer from stability issues: so electron orbit, transverse electron optics, electron bunch compression and other parameters have to be readjusted often to account for drifts in performance of various components. The tuning procedures typically employed in operation are often manual and lengthy. We have been developing a combination of model-free and model-based automatic tuning methods to meet the needs of present and upcoming XFEL facilities. Our approach has been implemented at FLASH to achieve automatic SASE tuning using empirical control of orbit, electron optics and bunch compression. In this paper we describe our approach to empirical tuning, the software which implements it, and the results of using it at FLASH.We also discuss the potential of using machine learning and model-based techniques in tuning methods.

  11. Development of an automatic pipeline scanning system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jae H.; Lee, Jae C.; Moon, Soon S.; Eom, Heung S.; Choi, Yu R

    1999-11-01

    Pressure pipe inspection in nuclear power plants is one of the mandatory regulation items. Comparing to manual ultrasonic inspection, automatic inspection has the benefits of more accurate and reliable inspection results and reduction of radiation disposal. final object of this project is to develop an automatic pipeline inspection system of pressure pipe welds in nuclear power plants. We developed a pipeline scanning robot with four magnetic wheels and 2-axis manipulator for controlling ultrasonic transducers, and developed the robot control computer which controls the robot to navigate along inspection path exactly. We expect our system can contribute to reduction of inspection time, performance enhancement, and effective management of inspection results. The system developed by this project can be practically used for inspection works after field tests. (author)

  12. Learning algorithms and automatic processing of languages

    International Nuclear Information System (INIS)

    Fluhr, Christian Yves Andre

    1977-01-01

    This research thesis concerns the field of artificial intelligence. It addresses learning algorithms applied to automatic processing of languages. The author first briefly describes some mechanisms of human intelligence in order to describe how these mechanisms are simulated on a computer. He outlines the specific role of learning in various manifestations of intelligence. Then, based on the Markov's algorithm theory, the author discusses the notion of learning algorithm. Two main types of learning algorithms are then addressed: firstly, an 'algorithm-teacher dialogue' type sanction-based algorithm which aims at learning how to solve grammatical ambiguities in submitted texts; secondly, an algorithm related to a document system which structures semantic data automatically obtained from a set of texts in order to be able to understand by references to any question on the content of these texts

  13. Paediatric Automatic Phonological Analysis Tools (APAT).

    Science.gov (United States)

    Saraiva, Daniela; Lousada, Marisa; Hall, Andreia; Jesus, Luis M T

    2017-12-01

    To develop the pediatric Automatic Phonological Analysis Tools (APAT) and to estimate inter and intrajudge reliability, content validity, and concurrent validity. The APAT were constructed using Excel spreadsheets with formulas. The tools were presented to an expert panel for content validation. The corpus used in the Portuguese standardized test Teste Fonético-Fonológico - ALPE produced by 24 children with phonological delay or phonological disorder was recorded, transcribed, and then inserted into the APAT. Reliability and validity of APAT were analyzed. The APAT present strong inter- and intrajudge reliability (>97%). The content validity was also analyzed (ICC = 0.71), and concurrent validity revealed strong correlations between computerized and manual (traditional) methods. The development of these tools contributes to fill existing gaps in clinical practice and research, since previously there were no valid and reliable tools/instruments for automatic phonological analysis, which allowed the analysis of different corpora.

  14. Automatic document navigation for digital content remastering

    Science.gov (United States)

    Lin, Xiaofan; Simske, Steven J.

    2003-12-01

    This paper presents a novel method of automatically adding navigation capabilities to re-mastered electronic books. We first analyze the need for a generic and robust system to automatically construct navigation links into re-mastered books. We then introduce the core algorithm based on text matching for building the links. The proposed method utilizes the tree-structured dictionary and directional graph of the table of contents to efficiently conduct the text matching. Information fusion further increases the robustness of the algorithm. The experimental results on the MIT Press digital library project are discussed and the key functional features of the system are illustrated. We have also investigated how the quality of the OCR engine affects the linking algorithm. In addition, the analogy between this work and Web link mining has been pointed out.

  15. Intelligent Storage System Based on Automatic Identification

    Directory of Open Access Journals (Sweden)

    Kolarovszki Peter

    2014-09-01

    Full Text Available This article describes RFID technology in conjunction with warehouse management systems. Article also deals with automatic identification and data capture technologies and each processes, which are used in warehouse management system. It describes processes from entering goods into production to identification of goods and also palletizing, storing, bin transferring and removing goods from warehouse. Article focuses on utilizing AMP middleware in WMS processes in Nowadays, the identification of goods in most warehouses is carried through barcodes. In this article we want to specify, how can be processes described above identified through RFID technology. All results are verified by measurement in our AIDC laboratory, which is located at the University of Žilina, and also in Laboratory of Automatic Identification Goods and Services located in GS1 Slovakia. The results of our research bring the new point of view and indicate the ways using of RFID technology in warehouse management system.

  16. Automatic Classification of Attacks on IP Telephony

    Directory of Open Access Journals (Sweden)

    Jakub Safarik

    2013-01-01

    Full Text Available This article proposes an algorithm for automatic analysis of attack data in IP telephony network with a neural network. Data for the analysis is gathered from variable monitoring application running in the network. These monitoring systems are a typical part of nowadays network. Information from them is usually used after attack. It is possible to use an automatic classification of IP telephony attacks for nearly real-time classification and counter attack or mitigation of potential attacks. The classification use proposed neural network, and the article covers design of a neural network and its practical implementation. It contains also methods for neural network learning and data gathering functions from honeypot application.

  17. Disentangling Complexity in Bayesian Automatic Adaptive Quadrature

    Science.gov (United States)

    Adam, Gheorghe; Adam, Sanda

    2018-02-01

    The paper describes a Bayesian automatic adaptive quadrature (BAAQ) solution for numerical integration which is simultaneously robust, reliable, and efficient. Detailed discussion is provided of three main factors which contribute to the enhancement of these features: (1) refinement of the m-panel automatic adaptive scheme through the use of integration-domain-length-scale-adapted quadrature sums; (2) fast early problem complexity assessment - enables the non-transitive choice among three execution paths: (i) immediate termination (exceptional cases); (ii) pessimistic - involves time and resource consuming Bayesian inference resulting in radical reformulation of the problem to be solved; (iii) optimistic - asks exclusively for subrange subdivision by bisection; (3) use of the weaker accuracy target from the two possible ones (the input accuracy specifications and the intrinsic integrand properties respectively) - results in maximum possible solution accuracy under minimum possible computing time.

  18. Automatic classification of defects in weld pipe

    International Nuclear Information System (INIS)

    Anuar Mikdad Muad; Mohd Ashhar Hj Khalid; Abdul Aziz Mohamad; Abu Bakar Mhd Ghazali; Abdul Razak Hamzah

    2000-01-01

    With the advancement of computer imaging technology, the image on hard radiographic film can be digitized and stored in a computer and the manual process of defect recognition and classification may be replace by the computer. In this paper a computerized method for automatic detection and classification of common defects in film radiography of weld pipe is described. The detection and classification processes consist of automatic selection of interest area on the image and then classify common defects using image processing and special algorithms. Analysis of the attributes of each defect such as area, size, shape and orientation are carried out by the feature analysis process. These attributes reveal the type of each defect. These methods of defect classification result in high success rate. Our experience showed that sharp film images produced better results

  19. TMB: Automatic differentiation and laplace approximation

    DEFF Research Database (Denmark)

    Kristensen, Kasper; Nielsen, Anders; Berg, Casper Willestofte

    2016-01-01

    are automatically integrated out. This approximation, and its derivatives, are obtained using automatic differentiation (up to order three) of the joint likelihood. The computations are designed to be fast for problems with many random effects (approximate to 10(6)) and parameters (approximate to 10...... computations. The user defines the joint likelihood for the data and the random effects as a C++ template function, while all the other operations are done in R; e.g., reading in the data. The package evaluates and maximizes the Laplace approximation of the marginal likelihood where the random effects......(3)). Computation times using ADMB and TMB are compared on a suite of examples ranging from simple models to large spatial models where the random effects are a Gaussian random field. Speedups ranging from 1.5 to about 100 are obtained with increasing gains for large problems...

  20. Automatic segmentation of vertebrae from radiographs

    DEFF Research Database (Denmark)

    Mysling, Peter; Petersen, Peter Kersten; Nielsen, Mads

    2011-01-01

    Segmentation of vertebral contours is an essential task in the design of automatic tools for vertebral fracture assessment. In this paper, we propose a novel segmentation technique which does not require operator interaction. The proposed technique solves the segmentation problem in a hierarchical...... manner. In a first phase, a coarse estimate of the overall spine alignment and the vertebra locations is computed using a shape model sampling scheme. These samples are used to initialize a second phase of active shape model search, under a nonlinear model of vertebra appearance. The search...... is constrained by a conditional shape model, based on the variability of the coarse spine location estimates. The technique is evaluated on a data set of manually annotated lumbar radiographs. The results compare favorably to the previous work in automatic vertebra segmentation, in terms of both segmentation...

  1. 11th Portuguese Conference on Automatic Control

    CERN Document Server

    Matos, Aníbal; Veiga, Germano

    2015-01-01

    During the last 20 years the Portuguese association of automatic control, Associação Portuguesa de Controlo Automático, with the sponsorship of IFAC have established the CONTROLO conference as a reference international forum where an effective exchange of knowledge and experience amongst researchers active in various theoretical and applied areas of systems and control can take place, always including considerable space for promoting new technical applications and developments, real-world challenges and success stories. In this 11th edition the CONTROLO conference evolved by introducing two strategic partnerships with Spanish and Brazilian associations in automatic control, Comité Español de Automática and Sociedade Brasileira de Automatica, respectively.

  2. Semi-automatic drawings surveying system

    International Nuclear Information System (INIS)

    Andriamampianina, Lala

    1983-01-01

    A system for the semi-automatic survey of drawings is presented. Its design has been oriented to the reduction of the stored information required for the drawing reproduction. This equipment consists mainly of a plotter driven by a micro-computer, but the pen of the plotter is replaced by a circular photodiode array. Line drawings are first viewed as a concatenation of vectors, with constant angle between the two vectors, and then divided in arcs of circles and line segments. A dynamic analysis of line intersections with the circular sensor permits to identify starting points and end points in a line, for the purpose of automatically following connected lines in drawing. The advantage of the method described is that precision practically depends only on the plotter performance, the sensor resolution being only considered for the thickness of strokes and the distance between two strokes. (author) [fr

  3. Automatic stereoscopic system for person recognition

    Science.gov (United States)

    Murynin, Alexander B.; Matveev, Ivan A.; Kuznetsov, Victor D.

    1999-06-01

    A biometric access control system based on identification of human face is presented. The system developed performs remote measurements of the necessary face features. Two different scenarios of the system behavior are implemented. The first one assumes the verification of personal data entered by visitor from console using keyboard or card reader. The system functions as an automatic checkpoint, that strictly controls access of different visitors. The other scenario makes it possible to identify visitors without any person identifier or pass. Only person biometrics are used to identify the visitor. The recognition system automatically finds necessary identification information preliminary stored in the database. Two laboratory models of recognition system were developed. The models are designed to use different information types and sources. In addition to stereoscopic images inputted to computer from cameras the models can use voice data and some person physical characteristics such as person's height, measured by imaging system.

  4. Automatic traveltime picking using instantaneous traveltime

    KAUST Repository

    Saragiotis, Christos

    2013-02-08

    Event picking is used in many steps of seismic processing. We present an automatic event picking method that is based on a new attribute of seismic signals, instantaneous traveltime. The calculation of the instantaneous traveltime consists of two separate but interrelated stages. First, a trace is mapped onto the time-frequency domain. Then the time-frequency representation is mapped back onto the time domain by an appropriate operation. The computed instantaneous traveltime equals the recording time at those instances at which there is a seismic event, a feature that is used to pick the events. We analyzed the concept of the instantaneous traveltime and demonstrated the application of our automatic picking method on dynamite and Vibroseis field data.

  5. Automatic transformations in the inference process

    Energy Technology Data Exchange (ETDEWEB)

    Veroff, R. L.

    1980-07-01

    A technique for incorporating automatic transformations into processes such as the application of inference rules, subsumption, and demodulation provides a mechanism for improving search strategies for theorem proving problems arising from the field of program verification. The incorporation of automatic transformations into the inference process can alter the search space for a given problem, and is particularly useful for problems having broad rather than deep proofs. The technique can also be used to permit the generation of inferences that might otherwise be blocked and to build some commutativity or associativity into the unification process. Appropriate choice of transformations, and new literal clashing and unification algorithms for applying them, showed significant improvement on several real problems according to several distinct criteria. 22 references, 1 figure.

  6. Meteorological Automatic Weather Station (MAWS) Instrument Handbook

    Energy Technology Data Exchange (ETDEWEB)

    Holdridge, Donna J [Argonne National Lab. (ANL), Argonne, IL (United States); Kyrouac, Jenni A [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-08-01

    The Meteorological Automatic Weather Station (MAWS) is a surface meteorological station, manufactured by Vaisala, Inc., dedicated to the balloon-borne sounding system (BBSS), providing surface measurements of the thermodynamic state of the atmosphere and the wind speed and direction for each radiosonde profile. These data are automatically provided to the BBSS during the launch procedure and included in the radiosonde profile as the surface measurements of record for the sounding. The MAWS core set of measurements is: Barometric Pressure (hPa), Temperature (°C), Relative Humidity (%), Arithmetic-Averaged Wind Speed (m/s), and Vector-Averaged Wind Direction (deg). The sensors that collect the core variables are mounted at the standard heights defined for each variable.

  7. Automatic Algorithm Selection for Complex Simulation Problems

    CERN Document Server

    Ewald, Roland

    2012-01-01

    To select the most suitable simulation algorithm for a given task is often difficult. This is due to intricate interactions between model features, implementation details, and runtime environment, which may strongly affect the overall performance. An automated selection of simulation algorithms supports users in setting up simulation experiments without demanding expert knowledge on simulation. Roland Ewald analyzes and discusses existing approaches to solve the algorithm selection problem in the context of simulation. He introduces a framework for automatic simulation algorithm selection and

  8. Authentic Material and Automaticity for Teaching English

    OpenAIRE

    Widyastuti, Widyastuti

    2017-01-01

    This article discusses how to make students of Science Education in first year feel interesting in English lesson, understanding the text well and can communicate English fluency. It has been suggested that Authentic Material and Automaticity Theory not only creates a friendly and fun condition in teaching reading but helps students to study comprehensibly so they are able to understand the text, structure, vocabulary easily, read fluently and they also can communicate in English. The authent...

  9. Automatic Control System Switching Roadway Lighting

    OpenAIRE

    Agus Trimuji Susilo; Lingga Hermanto Drs. MM

    2002-01-01

    Lack of attention to the information officer street lights, cause is not exactly the timewhen the blame lights street lighting street - the street in this city protocol. And whenit was already dark, the lights had not lit, so it can harm the users of the road. Werecommend that when it got bright lights - the lights switched off late, so muchelectricity is wasted with nothing - nothing.Given the problems above, the automatic switching is required that can control all thelights - the existing l...

  10. Research on automatic control system of greenhouse

    Science.gov (United States)

    Liu, Yi; Qi, Guoyang; Li, Zeyu; Wu, Qiannan; Meng, Yupeng

    2017-03-01

    This paper introduces a kind of automatic control system of single-chip microcomputer and a temperature and humidity sensor based on the greenhouse, describes the system's hardware structure, working principle and process, and a large number of experiments on the effect of the control system, the results show that the system can ideally control temperature and room temperature and humidity, can be used in indoor breeding and planting, and has the versatility and portability.

  11. Automatic genre classification of music content

    OpenAIRE

    Scaringella, N.; Zoia, G.; Mlynek, D.

    2006-01-01

    This paper reviews the state-of-the-art in automatic genre classification of music collections through three main paradigms: expert systems, unsupervised classification, and supervised classification. The paper discusses the importance of music genres with their definitions and hierarchies. It also presents techniques to extract meaningful information from audio data to characterize musical excerpts. The paper also presents the results of new emerging research fields and techniques that inves...

  12. Statistical Automatic Summarization in Organic Chemistry

    OpenAIRE

    Boudin, Florian; Velazquez-Morales, Patricia; Torres-Moreno, Juan-Manuel

    2009-01-01

    We present an oriented numerical summarizer algorithm, applied to producing automatic summaries of scientific documents in Organic Chemistry. We present its implementation named Yachs (Yet Another Chemistry Summarizer) that combines a specific document pre-processing with a sentence scoring method relying on the statistical properties of documents. We show that Yachs achieves the best results among several other summarizers on a corpus of Organic Chemistry articles.

  13. Automatic blood detection in capsule endoscopy video

    Czech Academy of Sciences Publication Activity Database

    Novozámský, Adam; Flusser, Jan; Tachecí, I.; Sulík, L.; Bureš, J.; Krejcar, O.

    2016-01-01

    Roč. 21, č. 12 (2016), s. 1-8, č. článku 126007. ISSN 1083-3668 R&D Projects: GA ČR GA15-16928S Institutional support: RVO:67985556 Keywords : Automatic blood detection * capsule endoscopy video Subject RIV: JD - Computer Applications, Robotics Impact factor: 2.530, year: 2016 http://library.utia.cas.cz/separaty/2016/ZOI/flusser-0466936.pdf

  14. Automatic Multimodal Cognitive Load Measurement (AMCLM)

    Science.gov (United States)

    2011-06-01

    increasing, while F2 is decreasing, as cognitive load is increased. Classification results performed on the Stroop test database show that formant...Final Project Report Grant AOARD-10-4029 Automatic Multimodal Cognitive Load Measurement (AMCLM) June 2011 NICTA DSIM Team...past year. At the start of the project, we carried out a literature review on video based physiological measures of cognitive load, focusing on

  15. Automatic evidence retrieval for systematic reviews.

    Science.gov (United States)

    Choong, Miew Keen; Galgani, Filippo; Dunn, Adam G; Tsafnat, Guy

    2014-10-01

    Snowballing involves recursively pursuing relevant references cited in the retrieved literature and adding them to the search results. Snowballing is an alternative approach to discover additional evidence that was not retrieved through conventional search. Snowballing's effectiveness makes it best practice in systematic reviews despite being time-consuming and tedious. Our goal was to evaluate an automatic method for citation snowballing's capacity to identify and retrieve the full text and/or abstracts of cited articles. Using 20 review articles that contained 949 citations to journal or conference articles, we manually searched Microsoft Academic Search (MAS) and identified 78.0% (740/949) of the cited articles that were present in the database. We compared the performance of the automatic citation snowballing method against the results of this manual search, measuring precision, recall, and F1 score. The automatic method was able to correctly identify 633 (as proportion of included citations: recall=66.7%, F1 score=79.3%; as proportion of citations in MAS: recall=85.5%, F1 score=91.2%) of citations with high precision (97.7%), and retrieved the full text or abstract for 490 (recall=82.9%, precision=92.1%, F1 score=87.3%) of the 633 correctly retrieved citations. The proposed method for automatic citation snowballing is accurate and is capable of obtaining the full texts or abstracts for a substantial proportion of the scholarly citations in review articles. By automating the process of citation snowballing, it may be possible to reduce the time and effort of common evidence surveillance tasks such as keeping trial registries up to date and conducting systematic reviews.

  16. Automatic modulation classification principles, algorithms and applications

    CERN Document Server

    Zhu, Zhechen

    2014-01-01

    Automatic Modulation Classification (AMC) has been a key technology in many military, security, and civilian telecommunication applications for decades. In military and security applications, modulation often serves as another level of encryption; in modern civilian applications, multiple modulation types can be employed by a signal transmitter to control the data rate and link reliability. This book offers comprehensive documentation of AMC models, algorithms and implementations for successful modulation recognition. It provides an invaluable theoretical and numerical comparison of AMC algo

  17. Automatic location of short circuit faults

    Energy Technology Data Exchange (ETDEWEB)

    Lehtonen, M. [VTT Energy, Espoo (Finland); Hakola, T.; Antila, E. [ABB Power Oy (Finland); Seppaenen, M. [North-Carelian Power Company (Finland)

    1998-08-01

    In this chapter, the automatic location of short circuit faults on medium voltage distribution lines, based on the integration of computer systems of medium voltage distribution network automation is discussed. First the distribution data management systems and their interface with the substation telecontrol, or SCADA systems, is studied. Then the integration of substation telecontrol system and computerized relay protection is discussed. Finally, the implementation of the fault location system is presented and the practical experience with the system is discussed

  18. Automatic targeting of plasma spray gun

    International Nuclear Information System (INIS)

    Abbatiello, L.A.; Neal, R.E.

    1978-01-01

    A means for monitoring the material portion in the flame of a plasma spray gun during spraying operations is described. A collimated detector, sensitive to certain wavelengths of light emission, is used to locate the centroid of the material with each pass of the gun. The response from the detector is then relayed to the gun controller to be used to automatically realign the gun

  19. Automatic Flight Controller With Model Inversion

    Science.gov (United States)

    Meyer, George; Smith, G. Allan

    1992-01-01

    Automatic digital electronic control system based on inverse-model-follower concept being developed for proposed vertical-attitude-takeoff-and-landing airplane. Inverse-model-follower control places inverse mathematical model of dynamics of controlled plant in series with control actuators of controlled plant so response of combination of model and plant to command is unity. System includes feedback to compensate for uncertainties in mathematical model and disturbances imposed from without.

  20. The evolution of transmission mode

    Science.gov (United States)

    Forbes, Mark R.; Hauffe, Heidi C.; Kallio, Eva R.; Okamura, Beth; Sait, Steven M.

    2017-01-01

    This article reviews research on the evolutionary mechanisms leading to different transmission modes. Such modes are often under genetic control of the host or the pathogen, and often in conflict with each other via trade-offs. Transmission modes may vary among pathogen strains and among host populations. Evolutionary changes in transmission mode have been inferred through experimental and phylogenetic studies, including changes in transmission associated with host shifts and with evolution of the unusually complex life cycles of many parasites. Understanding the forces that determine the evolution of particular transmission modes presents a fascinating medley of problems for which there is a lack of good data and often a lack of conceptual understanding or appropriate methodologies. Our best information comes from studies that have been focused on the vertical versus horizontal transmission dichotomy. With other kinds of transitions, theoretical approaches combining epidemiology and population genetics are providing guidelines for determining when and how rapidly new transmission modes may evolve, but these are still in need of empirical investigation and application to particular cases. Obtaining such knowledge is a matter of urgency in relation to extant disease threats. This article is part of the themed issue ‘Opening the black box: re-examining the ecology and evolution of parasite transmission’. PMID:28289251

  1. Next Generation Model 8800 Automatic TLD Reader

    International Nuclear Information System (INIS)

    Velbeck, K.J.; Streetz, K.L.; Rotunda, J.E.

    1999-01-01

    BICRON NE has developed an advanced version of the Model 8800 Automatic TLD Reader. Improvements in the reader include a Windows NT TM -based operating system and a Pentium microprocessor for the host controller, a servo-controlled transport, a VGA display, mouse control, and modular assembly. This high capacity reader will automatically read fourteen hundred TLD Cards in one loading. Up to four elements in a card can be heated without mechanical contact, using hot nitrogen gas. Improvements in performance include an increased throughput rate and more precise card positioning. Operation is simplified through easy-to-read Windows-type screens. Glow curves are displayed graphically along with light intensity, temperature, and channel scaling. Maintenance and diagnostic aids are included for easier troubleshooting. A click of a mouse will command actions that are displayed in easy-to-understand English words. Available options include an internal 90 Sr irradiator, automatic TLD calibration, and two different extremity monitoring modes. Results from testing include reproducibility, reader stability, linearity, detection threshold, residue, primary power supply voltage and frequency, transient voltage, drop testing, and light leakage. (author)

  2. Authentic Material and Automaticity for Teaching English

    Directory of Open Access Journals (Sweden)

    Widyastuti Widyastuti

    2017-07-01

    Full Text Available This article discusses how to make students of Science Education in first year feel interesting in English lesson, understanding the text well and can communicate English fluency. It has been suggested that Authentic Material and Automaticity Theory not only creates a friendly and fun condition in teaching reading but helps students to study comprehensibly so they are able to understand the text, structure, vocabulary easily, read fluently and they also can communicate in English. The authentic material can make the teaching learning process fun and eliminate boring because the topics and materials can be found in internet so it will be more visually and  interactive . Automaticity theory can solve the problem of students who must memorize words that make them feel boring and forget the words soon. The other benefit is the students can exposure the real language being used in a real context and stimulate studens’idea, encouarage them to relate themselves with real-life experiencesThese strategies can make the students understand easily and enjoy the teaching learning process. By combining authentic material and automaticity strategies for teaching English in science education, will develop readers (students to become fully competent and fluent.

  3. Fuzzy Logic Based Automatic Door Control System

    Directory of Open Access Journals (Sweden)

    Harun SUMBUL

    2017-12-01

    Full Text Available In this paper, fuzzy logic based an automatic door control system is designed to provide for heat energy savings. The heat energy loss usually occurs in where outomotic doors are used. Designed fuzzy logic system’s Input statuses (WS: Walking Speed and DD: Distance Door and the output status (DOS: Door Opening Speed is determined. According to these cases, rule base (25 rules is created; the rules are processed by a fuzzy logic and by appyled to control of an automatic door. An interface program is prepared by using Matlab Graphical User Interface (GUI programming language and some sample results are checked on Matlab using fuzzy logic toolbox. Designed fuzzy logic controller is tested at different speed cases and the results are plotted. As a result; in this study, we have obtained very good results in control of an automatic door with fuzzy logic. The results of analyses have indicated that the controls performed with fuzzy logic provided heat energy savings, less heat energy loss and reliable, consistent controls and that are feasible to in real.

  4. Automatic Detection of Electric Power Troubles (ADEPT)

    Science.gov (United States)

    Wang, Caroline; Zeanah, Hugh; Anderson, Audie; Patrick, Clint; Brady, Mike; Ford, Donnie

    1988-11-01

    Automatic Detection of Electric Power Troubles (A DEPT) is an expert system that integrates knowledge from three different suppliers to offer an advanced fault-detection system. It is designed for two modes of operation: real time fault isolation and simulated modeling. Real time fault isolation of components is accomplished on a power system breadboard through the Fault Isolation Expert System (FIES II) interface with a rule system developed in-house. Faults are quickly detected and displayed and the rules and chain of reasoning optionally provided on a laser printer. This system consists of a simulated space station power module using direct-current power supplies for solar arrays on three power buses. For tests of the system's ablilty to locate faults inserted via switches, loads are configured by an INTEL microcomputer and the Symbolics artificial intelligence development system. As these loads are resistive in nature, Ohm's Law is used as the basis for rules by which faults are located. The three-bus system can correct faults automatically where there is a surplus of power available on any of the three buses. Techniques developed and used can be applied readily to other control systems requiring rapid intelligent decisions. Simulated modeling, used for theoretical studies, is implemented using a modified version of Kennedy Space Center's KATE (Knowledge-Based Automatic Test Equipment), FIES II windowing, and an ADEPT knowledge base.

  5. Simplified automatic on-line document searching

    International Nuclear Information System (INIS)

    Ebinuma, Yukio

    1983-01-01

    The author proposed searching method for users who need not-comprehensive retrieval. That is to provide flexible number of related documents for the users automatically. A group of technical terms are used as search terms to express an inquiry. Logical sums of the terms in the ascending order of frequency of the usage are prepared sequentially and automatically, and then the search formulas, qsub(m) and qsub(m-1) which meet certain threshold values are selected automatically also. Users justify precision of the search output up to 20 items retrieved by the formula qsub(m). If a user wishes more than 30% of recall ratio, the serach result should be output by qsub(m), and if he wishes less than 30% of it, it should be output by qsub(m-1). The search by this method using one year volume of INIS Database (76,600 items) and five inquiries resulted in 32% of recall ratio and 36% of precision ratio on the average in the case of qsub(m). The connecting time of a terminal was within 15 minutes per an inquiry. It showed more efficiency than that of an inexperienced searcher. The method can be applied to on-line searching system for database in which natural language only or natural language and controlled vocabulary are used. (author)

  6. An Automatic Indirect Immunofluorescence Cell Segmentation System

    Directory of Open Access Journals (Sweden)

    Yung-Kuan Chan

    2014-01-01

    Full Text Available Indirect immunofluorescence (IIF with HEp-2 cells has been used for the detection of antinuclear autoantibodies (ANA in systemic autoimmune diseases. The ANA testing allows us to scan a broad range of autoantibody entities and to describe them by distinct fluorescence patterns. Automatic inspection for fluorescence patterns in an IIF image can assist physicians, without relevant experience, in making correct diagnosis. How to segment the cells from an IIF image is essential in developing an automatic inspection system for ANA testing. This paper focuses on the cell detection and segmentation; an efficient method is proposed for automatically detecting the cells with fluorescence pattern in an IIF image. Cell culture is a process in which cells grow under control. Cell counting technology plays an important role in measuring the cell density in a culture tank. Moreover, assessing medium suitability, determining population doubling times, and monitoring cell growth in cultures all require a means of quantifying cell population. The proposed method also can be used to count the cells from an image taken under a fluorescence microscope.

  7. Robust automatic camera pointing for airborne surveillance

    Science.gov (United States)

    Dwyer, David; Wren, Lee; Thornton, John; Bonsor, Nigel

    2002-08-01

    Airborne electro-optic surveillance from a moving platform currently requires regular interaction from a trained operator. Even simple tasks such as fixating on a static point on the ground can demand constant adjustment of the camera orientation to compensate for platform motion. In order to free up operator time for other tasks such as navigation and communication with ground assets, an automatic gaze control system is needed. This paper describes such a system, based purely on tracking points within the video image. A number of scene points are automatically selected and their inter-frame motion tracked. The scene motion is then estimated using a model of a planar projective transform. For reliable and accurate camera pointing, the modeling of the scene motion must be robust to common problems such as scene point obscuration, objects moving independently within the scene and image noise. This paper details a COTS based system for automatic camera fixation and describes ways of preventing objects moving in the scene or poor motion estimates from corrupting the scene motion model.

  8. Improving suspended sediment measurements by automatic samplers.

    Science.gov (United States)

    Gettel, Melissa; Gulliver, John S; Kayhanian, Masoud; DeGroot, Gregory; Brand, Joshua; Mohseni, Omid; Erickson, Andrew J

    2011-10-01

    Suspended solids either as total suspended solids (TSS) or suspended sediment concentration (SSC) is an integral particulate water quality parameter that is important in assessing particle-bound contaminants. At present, nearly all stormwater runoff quality monitoring is performed with automatic samplers in which the sampling intake is typically installed at the bottom of a storm sewer or channel. This method of sampling often results in a less accurate measurement of suspended sediment and associated pollutants due to the vertical variation in particle concentration caused by particle settling. In this study, the inaccuracies associated with sampling by conventional intakes for automatic samplers have been verified by testing with known suspended sediment concentrations and known particle sizes ranging from approximately 20 μm to 355 μm under various flow rates. Experimental results show that, for samples collected at a typical automatic sampler intake position, the ratio of sampled to feed suspended sediment concentration is up to 6600% without an intake strainer and up to 300% with a strainer. When the sampling intake is modified with multiple sampling tubes and fitted with a wing to provide lift (winged arm sampler intake), the accuracy of sampling improves substantially. With this modification, the differences between sampled and feed suspended sediment concentration were more consistent and the sampled to feed concentration ratio was accurate to within 10% for particle sizes up to 250 μm.

  9. Automatic operation device for control rods

    International Nuclear Information System (INIS)

    Sekimizu, Koichi

    1984-01-01

    Purpose: To enable automatic operation of control rods based on the reactor operation planning, and particularly, to decrease the operator's load upon start up and shutdown of the reactor. Constitution: Operation plannings, demand for the automatic operation, break point setting value, power and reactor core flow rate change, demand for operation interrupt, demand for restart, demand for forecasting and the like are inputted to an input device, and an overall judging device performs a long-term forecast as far as the break point by a long-term forecasting device based on the operation plannings. The automatic reactor operation or the like is carried out based on the long-term forecasting and the short time forecasting is performed by the change in the reactor core status due to the control rod operation sequence based on the control rod pattern and the operation planning. Then, it is judged if the operation for the intended control rod is possible or not based on the result of the short time forecasting. (Aizawa, K.)

  10. Automatic approach to deriving fuzzy slope positions

    Science.gov (United States)

    Zhu, Liang-Jun; Zhu, A.-Xing; Qin, Cheng-Zhi; Liu, Jun-Zhi

    2018-03-01

    Fuzzy characterization of slope positions is important for geographic modeling. Most of the existing fuzzy classification-based methods for fuzzy characterization require extensive user intervention in data preparation and parameter setting, which is tedious and time-consuming. This paper presents an automatic approach to overcoming these limitations in the prototype-based inference method for deriving fuzzy membership value (or similarity) to slope positions. The key contribution is a procedure for finding the typical locations and setting the fuzzy inference parameters for each slope position type. Instead of being determined totally by users in the prototype-based inference method, in the proposed approach the typical locations and fuzzy inference parameters for each slope position type are automatically determined by a rule set based on prior domain knowledge and the frequency distributions of topographic attributes. Furthermore, the preparation of topographic attributes (e.g., slope gradient, curvature, and relative position index) is automated, so the proposed automatic approach has only one necessary input, i.e., the gridded digital elevation model of the study area. All compute-intensive algorithms in the proposed approach were speeded up by parallel computing. Two study cases were provided to demonstrate that this approach can properly, conveniently and quickly derive the fuzzy slope positions.

  11. Mental imagery affects subsequent automatic defense responses

    Directory of Open Access Journals (Sweden)

    Muriel A Hagenaars

    2015-06-01

    Full Text Available Automatic defense responses promote survival and appropriate action under threat. They have also been associated with the development of threat-related psychiatric syndromes. Targeting such automatic responses during threat may be useful in populations with frequent threat exposure. Here, two experiments explored whether mental imagery as a pre-trauma manipulation could influence fear bradycardia (a core characteristic of freezing during subsequent analogue trauma (affective picture viewing. Image-based interventions have proven successful in the treatment of threat-related disorders, and are easily applicable. In Experiment 1 43 healthy participants were randomly assigned to an imagery script condition. Participants executed a passive viewing task with blocks of neutral, pleasant and unpleasant pictures after listening to an auditory script that was either related (with a positive or a negative outcome or unrelated to the unpleasant pictures from the passive viewing task. Heart rate was assessed during script listening and during passive viewing. Imagining negative related scripts resulted in greater bradycardia (neutral-unpleasant contrast than imagining positive scripts, especially unrelated. This effect was replicated in Experiment 2 (N = 51, again in the neutral-unpleasant contrast. An extra no-script condition showed that bradycardia was not induced by the negative related script, but rather that a positive script attenuated bradycardia. These preliminary results might indicate reduced vigilance after unrelated positive events. Future research should replicate these findings using a larger sample. Either way, the findings show that highly automatic defense behavior can be influenced by relatively simple mental imagery manipulations.

  12. Development of an automatic reactor inspection system

    International Nuclear Information System (INIS)

    Kim, Jae Hee; Eom, Heung Seop; Lee, Jae Cheol; Choi, Yoo Raek; Moon, Soon Seung

    2002-02-01

    Using recent technologies on a mobile robot computer science, we developed an automatic inspection system for weld lines of the reactor vessel. The ultrasonic inspection of the reactor pressure vessel is currently performed by commercialized robot manipulators. Since, however, the conventional fixed type robot manipulator is very huge, heavy and expensive, it needs long inspection time and is hard to handle and maintain. In order to resolve these problems, we developed a new automatic inspection system using a small mobile robot crawling on the vertical wall of the reactor vessel. According to our conceptual design, we developed the reactor inspection system including an underwater inspection robot, a laser position control subsystem, an ultrasonic data acquisition/analysis subsystem and a main control subsystem. We successfully carried out underwater experiments on the reactor vessel mockup, and real reactor ready for Ulchine nuclear power plant unit 6 at Dusan Heavy Industry in Korea. After this project, we have a plan to commercialize our inspection system. Using this system, we can expect much reduction of the inspection time, performance enhancement, automatic management of inspection history, etc. In the economic point of view, we can also expect import substitution more than 4 million dollars. The established essential technologies for intelligent control and automation are expected to be synthetically applied to the automation of similar systems in nuclear power plants

  13. Transmission Line Series Compensation for Wind Energy Transmission

    International Nuclear Information System (INIS)

    Palanichamy, C; Wong, Y C

    2015-01-01

    Wind energy has demonstrated to be a clean, copious and absolutely renewable source of energy, and the large penetration of it into the power grid indicates that wind energy is considered an effective means of power generation, Transmission of wind energy from remote locations to load centers necessitates long transmission lines. Series compensation is a proven and economical transmission solution to address system power transfer strength, grid stability, and voltage profile issues of long transmission lines. In this paper, a programmable approach to determine the capacitive reactance of series capacitor and optimum location for its placement to achieve maximum power transfer gas been presented. The respective program with sample solutions has been provided for real-time applications. (paper)

  14. What Automaticity Deficit? Activation of Lexical Information by Readers with Dyslexia in a Rapid Automatized Naming Stroop-Switch Task

    Science.gov (United States)

    Jones, Manon W.; Snowling, Margaret J.; Moll, Kristina

    2016-01-01

    Reading fluency is often predicted by rapid automatized naming (RAN) speed, which as the name implies, measures the automaticity with which familiar stimuli (e.g., letters) can be retrieved and named. Readers with dyslexia are considered to have less "automatized" access to lexical information, reflected in longer RAN times compared with…

  15. The evolution of plant virus transmission pathways

    Science.gov (United States)

    Frédéric M. Hamelin; Linda J.S. Allen; Holly R. Prendeville; M. Reza Hajimorad; Michael J. Jeger

    2016-01-01

    The evolution of plant virus transmission pathways is studied through transmission via seed, pollen, oravector. We address the questions: under what circumstances does vector transmission make pollen transmission redundant? Can evolution lead to the coexistence of multiple virus transmission pathways? We restrict the analysis to an annual plant population in which...

  16. Analytics on Transmission Electron Microscopy

    International Nuclear Information System (INIS)

    Keum, Dong Hwa; Kim, Geung Ho; Lee, Hwak Ju and others

    1996-06-01

    This book gives descriptions of transmission electron microscopy, which deals with electron microscopy and materials science, history of electron microscopy, application of analytics on transmission electron microscopy, machine requirement of transmission electron microscopy like electron gun and TEM image and function, crystal diffraction, electron diffraction, Kikuchi's diffraction figure, analysis of diffraction figure, contrast of TEM image like absorption contrast, and phase contrast, Fresnel's diffraction and TEM contrast, thickness fringe, column approximation, analysis of diffraction contrast, image simulation, and electron energy loss spectrometry.

  17. Schistosomiasis transmission in Lake Malawi

    DEFF Research Database (Denmark)

    Madsen, H.; Stauffer, J. R.; Bloch, P.

    2004-01-01

    Schistosomiasis (bilharziasis) transmission due to Schistosoma haematobium has for many years been known to occur along protected shorelines in Lake Malawi, but the recent finding that transmission also can also occur along open shorelines with sandy sediment has had a detrimental effect on tourism...... to Lake Malawi. The present paper shows that transmission, as evidenced from presence of intermediate hosts, along open shorelines is occurring in the southern part of the Lake. Relatively simple precautions can be taken to ensure minimal risk of attracting schistosome infection, and the schistosomiasis...

  18. Midwest Transmission Workshop I Summary

    Energy Technology Data Exchange (ETDEWEB)

    Kevin Bryan

    2001-05-01

    OAK-B135 The meeting was opened with a review of the purposes of the workshop: (1) Present and discuss key studies and assessments of transmission upgrades, additions and related issues for the upper Midwest, including work that addresses the full range of views on these topics; (2) Understand the various transmission issues in the upper Midwest and discuss options for addressing the issues; and (3) Identify the decision makers and entities that need to play an active role if transmission issues are to be resolved, and agree on next steps for engaging these individuals and organizations through education, outreach, and information dissemination.

  19. Markets for financial transmission rights

    International Nuclear Information System (INIS)

    Kristiansen, T.

    2004-01-01

    Results of a survey of markets for financial transmission rights that facilitate competitive, open and non-discriminatory electricity market design are discussed. Specifically, the survey covered Pennsylvania, New Jersey, Maryland (PJM), New York, California, New England, Texas and New Zealand. The main emphasis was on the PJM and the New York markets, since they are the most mature. Interwowen with the results is a thorough discussion of the properties, features and the design of financial transaction rights in the various jurisdictions, the advantages, disadvantages and market performance of financial transmission rights, market performance criteria, and the mechanism for acquiring financial transmission rights. 49 refs., 14 tabs., 6 figs

  20. Intertwined arbovirus transmission activity: reassessing the transmission cycle paradigm.

    Directory of Open Access Journals (Sweden)

    Luis Adrian Diaz

    2013-01-01

    Full Text Available Arboviruses are emerging/reemerging infectious agents worldwide. The factors within this scenario include vector and host population fluctuations, climatic changes, anthropogenic activities that disturb ecosystems, an increase in international flights, human mobility, and genetic mutations that allow spill-over phenomenon. Arboviruses are maintained by biologic transmission among vectors and hosts. Sometimes this biological transmission is specific and includes one vector and host species such as CHK, DEN and urban YFV. However, most of the arboviruses are generalist and they use many vectors and hosts species. From this perspective, arboviruses are maintained through a transmission network rather than a transmission cycle. This allows us to understand the complexity and dynamics of the transmission and maintenance of arboviruses in the ecosystems. The old perspective that arboviruses are maintained in close and stable transmission cycles should be modified by a new more integrative and dynamic idea, representing the real scenario where biological interactions have a much broader representation, indicating the constant adaptability of the biological entities.

  1. Sensitivity analysis and design optimization through automatic differentiation

    International Nuclear Information System (INIS)

    Hovland, Paul D; Norris, Boyana; Strout, Michelle Mills; Bhowmick, Sanjukta; Utke, Jean

    2005-01-01

    Automatic differentiation is a technique for transforming a program or subprogram that computes a function, including arbitrarily complex simulation codes, into one that computes the derivatives of that function. We describe the implementation and application of automatic differentiation tools. We highlight recent advances in the combinatorial algorithms and compiler technology that underlie successful implementation of automatic differentiation tools. We discuss applications of automatic differentiation in design optimization and sensitivity analysis. We also describe ongoing research in the design of language-independent source transformation infrastructures for automatic differentiation algorithms

  2. Presentation video retrieval using automatically recovered slide and spoken text

    Science.gov (United States)

    Cooper, Matthew

    2013-03-01

    Video is becoming a prevalent medium for e-learning. Lecture videos contain text information in both the presentation slides and lecturer's speech. This paper examines the relative utility of automatically recovered text from these sources for lecture video retrieval. To extract the visual information, we automatically detect slides within the videos and apply optical character recognition to obtain their text. Automatic speech recognition is used similarly to extract spoken text from the recorded audio. We perform controlled experiments with manually created ground truth for both the slide and spoken text from more than 60 hours of lecture video. We compare the automatically extracted slide and spoken text in terms of accuracy relative to ground truth, overlap with one another, and utility for video retrieval. Results reveal that automatically recovered slide text and spoken text contain different content with varying error profiles. Experiments demonstrate that automatically extracted slide text enables higher precision video retrieval than automatically recovered spoken text.

  3. [The effects of rumination on automatic thoughts and depressive symptoms].

    Science.gov (United States)

    Nishikawa, Daiji; Matsunaga, Miki; Furutani, Kaichiro

    2013-12-01

    This study investigated the effects of rumination (reflective pondering and brooding) on automatic thoughts (both negative and positive) and depressive symptoms. University students (N=183; 96 men) completed the Self-Rating Depression Scale (SDS), Automatic Thoughts Questionnaire-Revised (ATQ-R), and Response Style Scale (RSS). We conducted a path analysis which included gender as a factor. The results revealed that brooding was associated with negative automatic thoughts. Negative automatic thoughts contributed to the aggravation of depressive symptoms. In contrast, reflective pondering was associated with positive automatic thoughts. Positive automatic thoughts contributed to the reduction of depressive symptoms. These results indicate that rumination does not affect depressive symptoms directly. We suggest that rumination affects depressive symptoms indirectly through automatic thoughts, and that there are gender differences in the influence process.

  4. Accounting-related transmission issues

    International Nuclear Information System (INIS)

    Niehaus, M.; Bjorn, P.; Pate, G.

    1999-01-01

    Various initiatives have been undertaken by the Federal Energy Regulatory Commission (FERC) to deregulate wholesale electric energy markets. These initiatives have focused on restructuring the transmission systems in the US and recently have culminated in a proposal requiring formation of and participation in regional transmission organizations. The overall form of regulation selected to determine rates for transmission entities as well as underlying regulatory decisions reached on key issues will have profound implications for transmission entities. For example, traditional cost-based regulation would require one set of accounting and reporting rules, while incentive-based regulation may not be subject to those same rules. An overview of some of the major accounting and financial reporting issues that will need to be considered is presented

  5. Fomite transmission in head lice.

    Science.gov (United States)

    Burkhart, Craig N; Burkhart, Craig G

    2007-06-01

    Control of various infestations requires an accurate understanding of transmission. After thousands of years of lice infestation, scientific documentation of indirect contact transmission has been substantiated. Lice can be transferred in the egg, instar, and adult stages. Lice have now been shown in the laboratory to be readily dislodged by air movements such as blow-drying one's hair, combing, and toweling. Moreover, passive transfer to adjoining fabric is also frequently observed. Louse transmission by fomites occurs more frequently than has been commonly believed. Close proximity suffices to increase the likeliness of a new infestation. Thus louse control measures should take account of fomite transmission and include screening of all individuals within an infested person's immediate circle of contact, laundering of everything within the infested individuals' bed or quarantining of such material for 10 days, thorough vacuuming of floors, carpets, upholstery, with a standard vacuum cleaner.

  6. Oral transmission of Chagas disease.

    Science.gov (United States)

    Shikanai-Yasuda, Maria Aparecida; Carvalho, Noemia Barbosa

    2012-03-01

    Chagas disease is now an active disease in the urban centers of countries of nonendemicity and endemicity because of congenital and blood and/or organ transplantation transmissions and the reactivation of the chronic disease in smaller scale than vectorial transmission, reported as controlled in countries of endemicity. Oral transmission of Chagas disease has emerged in unpredictable situations in the Amazon region and, more rarely, in areas of nonendemicity where the domiciliary triatomine cycle was under control because of exposition of the food to infected triatomine and contaminated secretions of reservoir hosts. Oral transmission of Chagas disease is considered when >1 acute case of febrile disease without other causes is linked to a suspected food and should be confirmed by the presence of the parasite after direct microscopic examination of the blood or other biological fluid sample from the patient.

  7. Echinococcosis : disease, detection and transmission

    NARCIS (Netherlands)

    Craig, P.S.; Rogan, M T; Campos-Ponce, M

    2003-01-01

    Echinococcosis is one of the world's most geographically widespread parasitic zoonoses, with transmission occurring in tropical, temperate and arctic biomes. Most human infections are due to Echinococcus granulosus transmitted between domestic dogs and livestock, but this cosmopolitan species also

  8. Transmission of Information: An Overview.

    Science.gov (United States)

    Thoma, George R.

    1981-01-01

    Outlines the basic principles underlying the transmission of information, including analog and digital modulation, limitations to communications, configurations of communications networks, optical fiber cables, and earth satellites. Six references are cited. (FM)

  9. Radio and line transmission 2

    CERN Document Server

    Roddy, Dermot

    2013-01-01

    Radio and Line Transmission, Volume 2 gives a detailed treatment of the subject as well as an introduction to additional advanced subject matter. Organized into 14 chapters, this book begins by explaining the radio wave propagation, signal frequencies, and bandwidth. Subsequent chapters describe the transmission lines and cables; the aerials; tuned and coupled circuits; bipolar transistor amplifiers; field-effect transistors and circuits; thermionic valve amplifiers; LC oscillators; the diode detectors and modulators; and the superheterodyne receiver. Other chapters explore noise and interfere

  10. Cardinality of UDP Transmission Outcomes

    OpenAIRE

    Weitl, Franz; Sebih, Nazim; Artho, Cyrille; Hagiya, Masami; Tanabe, Yoshinori; Yamagata, Yoriyuki; Yamamoto, Mitsuharu

    2015-01-01

    This paper examines the cost of testing network applications using the User Datagram Protocol (UDP). Such applications must deal with packet loss, duplication, and reordering. Ideally, a UDP application should be tested against all possible outcomes of unreliable UDP transmissions. Their number, however, grows at least exponentially in the number of transmitted packets. To estimate the cost of the exhaustive testing of UDP applications, we determine the number of UDP transmission outcomes ana...

  11. Heartland Alliance for Regional Transmission

    Energy Technology Data Exchange (ETDEWEB)

    Jackson, Nancy [Climate and Energy Project, Inc., Hutchinson, KS (United States)

    2017-03-15

    The Heartland Alliance for Regional Transmission (HART) will foster a candid, productive conversation among stakeholders that identifies challenges to and benefits from a massive build out of wind generation and transmission across the Southwest Power Pool. Based on the outcomes of those deliberations, HART will develop and deliver an ambitious, coordinated, peer-to-peer outreach effort that spans the SPP to improve market acceptance for wind.

  12. Optical transmissivity of metallic nanowires

    Science.gov (United States)

    Nairat, Mazen S.

    2017-08-01

    Optical transmissivity and reflectivity of one dimensional array of metallic nanowires embedded in transparent dielectric is characterized. i employ wave optics simulation to analyze the optical field distribution in both the dielectric and the nanowires. The results indicate that the transmissivity and reflectivity depend on the polarization states of the incident light. The metallic nanowires matrix transmit in-plane polarization but block light out at of-plane polarization.

  13. Transmission Control of Transport and Technological Cars in Acceleration Mode

    Directory of Open Access Journals (Sweden)

    B. I. Plujnikov

    2015-01-01

    Full Text Available In most structures a transmission of the transport-technological machine (TTM is controlled by automatic systems. In their creating it is necessary to specify the appropriate parameters and algorithms. In the total balance of the machine run time the acceleration mode is the most important. Therefore, an algorithm of the transmission gear ratio change during acceleration largely provides desirable rating of machines.It is known that the process of acceleration is estimated by its dynamic quality and fuel economy. To reach the best rating of both simultaneously is impossible. Therefore, as the criteria of estimate, were chosen the time and fuel consumption during acceleration to a fixed speed value.From a mathematical point of view, these criteria represent the sum of integrals, each of which defines the time or the fuel consumption during acceleration with a certain transmission gear ratio. The problem is formulated as follows: to determine the speed values of the TTM at the moments when the transmission gear ratio is changed providing the minimum values during fixed fuel supply for the estimate criteria. The latter condition in a certain way limits the task, but in explicit form there is no this control action in the dependence data.Given the variety of possible design options for the TTM, the solution is given by a specific example that simplifies the mathematics and makes it easier to understand the results obtained. As a TTM, is considered a passenger car with petrol engine and automatic transmission, which includes a hydrodynamic transformer and three-speed gearbox.A chosen way of solving the problem involves using the theory of ordinary maxima and minima, which allows finding the unknown values of independent variables. The expressions of sub-integral functions are in explicit form obtained and studied for meeting the necessary and sufficient conditions for existence of the extreme point. The result was a proof that in the case of

  14. Evaluating the merchant transmission market

    International Nuclear Information System (INIS)

    Hsieh, E.; Bartholomew Fisher, E.

    2007-01-01

    This paper reviewed the North American bulk electric transmission system, with particular reference to the following merchant power transmission projects that have applied to sell transmission at negotiated rates by the Federal Energy Regulatory Commission (FERC): Cross Sound Cable; Neptune Phase 1; TransCanada's Northern Lights HVDC line; Montana Alberta Tie; Juan de Fuca Cable; Linden VFT; Connecticut-Long Island Cable; Lake Erie Link; Empire Connection; Harbor Cable; Chesapeake Transmission; and the Neptune/Green Line. The projects were sorted by status as either active, inactive and restructured. Each summary included the interconnection points, capacity, and sponsor. This paper also identified the major hurdles in their approvals. The relative success of the merchant transmission framework in attracting new investment was then reviewed. The successful projects shared 3 common attributes. They connected areas with large price differentials and they used advanced flow control technology such as HVDC, PARs, and VFTs. The successful projects also bridged some type of border, either geographic, electrical, economic, or a combination. Three of the active projects crossed the Canadian-US border, while the other 3 connected New York City to neighbouring regions. It was shown that merchant transmission fills a niche, enabling market responses to connect areas that may be overlooked by a regional planning process. 27 refs

  15. Automatic fog detection for public safety by using camera images

    Science.gov (United States)

    Pagani, Giuliano Andrea; Roth, Martin; Wauben, Wiel

    2017-04-01

    Fog and reduced visibility have considerable impact on the performance of road, maritime, and aeronautical transportation networks. The impact ranges from minor delays to more serious congestions or unavailability of the infrastructure and can even lead to damage or loss of lives. Visibility is traditionally measured manually by meteorological observers using landmarks at known distances in the vicinity of the observation site. Nowadays, distributed cameras facilitate inspection of more locations from one remote monitoring center. The main idea is, however, still deriving the visibility or presence of fog by an operator judging the scenery and the presence of landmarks. Visibility sensors are also used, but they are rather costly and require regular maintenance. Moreover, observers, and in particular sensors, give only visibility information that is representative for a limited area. Hence the current density of visibility observations is insufficient to give detailed information on the presence of fog. Cameras are more and more deployed for surveillance and security reasons in cities and for monitoring traffic along main transportation ways. In addition to this primary use of cameras, we consider cameras as potential sensors to automatically identify low visibility conditions. The approach that we follow is to use machine learning techniques to determine the presence of fog and/or to make an estimation of the visibility. For that purpose a set of features are extracted from the camera images such as the number of edges, brightness, transmission of the image dark channel, fractal dimension. In addition to these image features, we also consider meteorological variables such as wind speed, temperature, relative humidity, and dew point as additional features to feed the machine learning model. The results obtained with a training and evaluation set consisting of 10-minute sampled images for two KNMI locations over a period of 1.5 years by using decision trees methods

  16. Transmission and reflection ellipsometry of thin films and multilayer systems.

    Science.gov (United States)

    Bader, G; Ashrit, P V; Truong, V V

    1998-03-01

    Ellipsometric studies are generally carried out in the reflection mode rather than in the transmission mode, requiring invariably opaque substrates or substrates in which the backreflection is minimized or suppressed by different methods. In the present research we used a transmission and reflection photoellipsometry method to study electrochromic materials and their multilayer systems deposited on thick substrates. The role of the substrate is examined carefully, and the contributions from multiple reflections in the substrate are taken into account in the theoretical treatment. This procedure not only allows the study of thin films deposited on quasi-transparent substrates, but when carried out in conjunction with reflection measurements it greatly improves the accuracy in the determination of the optical constants. Optical measurements are carried out on an automatic reflection transmission spectroscopic ellipsometer. Solid-state ionic materials used in electrochromic systems such as indium tin oxide, tungsten oxide, and their multilayer structures deposited on glass substrates are used as examples. A software based on the above theory, optikan, was developed to model and analyze such systems. It is demonstrated that the photoellipsometry method proposed is especially suited to analyzing electrochromic materials and transmitting devices in a nondestructive way.

  17. An automatic sample changer for gamma spectrometry

    International Nuclear Information System (INIS)

    Andrews, D.J.

    1984-01-01

    An automatic sample changer for gamma spectrometry is described which is designed for large-volume, low radioactivity environmental samples of various sizes up to maximum dimensions 100 mm diameter x 60 mm high. The sample changer is suitable for use with most existing gamma spectrometry systems which utilize GeLi or NaI detectors in vertical mode, in conjunction with a pulse height analyzer having auto-cycle and suitable data output facilities; it is linked to a Nuclear Data ND 6620 computer-based analysis system. (U.K.)

  18. A Context Dependent Automatic Target Recognition System

    Science.gov (United States)

    Kim, J. H.; Payton, D. W.; Olin, K. E.; Tseng, D. Y.

    1984-06-01

    This paper describes a new approach to automatic target recognizer (ATR) development utilizing artificial intelligent techniques. The ATR system exploits contextual information in its detection and classification processes to provide a high degree of robustness and adaptability. In the system, knowledge about domain objects and their contextual relationships is encoded in frames, separating it from low level image processing algorithms. This knowledge-based system demonstrates an improvement over the conventional statistical approach through the exploitation of diverse forms of knowledge in its decision-making process.

  19. Wallac automatic alarm dosimeter type RAD21

    International Nuclear Information System (INIS)

    Burgess, P. H.; Iles, W.J.

    1980-02-01

    The Automatic Alarm Dosimeter type RAD 21 is a batterypowered personal dosemeter and exposure rate alarm monitor, designed to be worn on the body, covering an exposure range from 0.1 to 999.9 mR and has an audible alarm which can be pre-set over the range 1 mR h -1 to 250 mR h -1 . The instrument is designed to measure x- and γ radiation over the energy range 50 keV to 3 MeV. The facilities and controls, the radiation, electrical, environmental and mechanical characteristics, and the manual, have been evaluated. (U.K.)

  20. The automatic electromagnetic field generating system

    Science.gov (United States)

    Audone, B.; Gerbi, G.

    1982-07-01

    The technical study and the design approaches adopted for the definition of the automatic electromagnetic field generating system (AEFGS) dedicated to EMC susceptibility testing are presented. The AEFGS covers the frequency range 10 KHz to 40 GHZ and operates successfully in the two EMC shielded chambers at ESTEC. The performance of the generators/amplifiers subsystems, antennas selection, field amplitude and susceptibility feedback and monitoring systems is described. System control modes which guarantee the AEFGS full operability under different test conditions are discussed. Advantages of automation of susceptibility testing include increased measurement accuracy and testing cost reduction.

  1. Automatic histogram threshold using fuzzy measures.

    Science.gov (United States)

    Vieira Lopes, Nuno; Mogadouro do Couto, Pedro A; Bustince, Humberto; Melo-Pinto, Pedro

    2010-01-01

    In this paper, an automatic histogram threshold approach based on a fuzziness measure is presented. This work is an improvement of an existing method. Using fuzzy logic concepts, the problems involved in finding the minimum of a criterion function are avoided. Similarity between gray levels is the key to find an optimal threshold. Two initial regions of gray levels, located at the boundaries of the histogram, are defined. Then, using an index of fuzziness, a similarity process is started to find the threshold point. A significant contrast between objects and background is assumed. Previous histogram equalization is used in small contrast images. No prior knowledge of the image is required.

  2. Automatic Angular alignment of LHC Collimators

    CERN Document Server

    Azzopardi, Gabriella; Salvachua Ferrando, Belen Maria; Mereghetti, Alessio; Bruce, Roderik; Redaelli, Stefano; CERN. Geneva. ATS Department

    2017-01-01

    The LHC is equipped with a complex collimation system to protect sensitive equipment from unavoidable beam losses. Collimators are positioned close to the beam using an alignment procedure. Until now they have always been aligned assuming no tilt between the collimator and the beam, however, tank misalignments or beam envelope angles at large-divergence locations could introduce a tilt limiting the collimation performance. Three different algorithms were implemented to automatically align a chosen collimator at various angles. The implementation was tested on a number of collimators during this MD and no human intervention was required.

  3. Accuracy analysis of automatic distortion correction

    Directory of Open Access Journals (Sweden)

    Kolecki Jakub

    2015-06-01

    Full Text Available The paper addresses the problem of the automatic distortion removal from images acquired with non-metric SLR camera equipped with prime lenses. From the photogrammetric point of view the following question arises: is the accuracy of distortion control data provided by the manufacturer for a certain lens model (not item sufficient in order to achieve demanded accuracy? In order to obtain the reliable answer to the aforementioned problem the two kinds of tests were carried out for three lens models.

  4. Automatic Visualization of Software Requirements: Reactive Systems

    International Nuclear Information System (INIS)

    Castello, R.; Mili, R.; Tollis, I.G.; Winter, V.

    1999-01-01

    In this paper we present an approach that facilitates the validation of high consequence system requirements. This approach consists of automatically generating a graphical representation from an informal document. Our choice of a graphical notation is statecharts. We proceed in two steps: we first extract a hierarchical decomposition tree from a textual description, then we draw a graph that models the statechart in a hierarchical fashion. The resulting drawing is an effective requirements assessment tool that allows the end user to easily pinpoint inconsistencies and incompleteness

  5. Uranium casting furnace automatic temperature control development

    International Nuclear Information System (INIS)

    Lind, R.F.

    1992-01-01

    Development of an automatic molten uranium temperature control system for use on batch-type induction casting furnaces is described. Implementation of a two-color optical pyrometer, development of an optical scanner for the pyrometer, determination of furnace thermal dynamics, and design of control systems are addressed. The optical scanning system is shown to greatly improve pyrometer measurement repeatability, particularly where heavy floating slag accumulations cause surface temperature gradients. Thermal dynamics of the furnaces were determined by applying least-squares system identification techniques to actual production data. A unity feedback control system utilizing a proportional-integral-derivative compensator is designed by using frequency-domain techniques. 14 refs

  6. Automatic generation of combinatorial test data

    CERN Document Server

    Zhang, Jian; Ma, Feifei

    2014-01-01

    This book reviews the state-of-the-art in combinatorial testing, with particular emphasis on the automatic generation of test data. It describes the most commonly used approaches in this area - including algebraic construction, greedy methods, evolutionary computation, constraint solving and optimization - and explains major algorithms with examples. In addition, the book lists a number of test generation tools, as well as benchmarks and applications. Addressing a multidisciplinary topic, it will be of particular interest to researchers and professionals in the areas of software testing, combi

  7. IR Thermometer with Automatic Emissivity Correction

    Directory of Open Access Journals (Sweden)

    A. Dobesch

    2013-12-01

    Full Text Available The paper describes the design and implementation of an infrared (IR thermometer with automatic emissivity correction. The temperature measurement is carried out by the simple digital thermopile sensor MLX90614. The emissivity correction is based on benefits of diffuse reflecting materials and it uses an IR laser diode in conjunction with a selective amplifier. Moreover, the paper includes the design of the control interface with a graphics LCD. Furthermore, this paper describes the power supply unit with a Li-ion cell controlled by basic integrated circuits.

  8. New automatic radiation monitoring network in Slovenia

    International Nuclear Information System (INIS)

    Cindro, M.; Vokal Nemec, B.

    2006-01-01

    The Slovenian Nuclear Safety Administration gathers all on-line dose rate data measured by the various automatic networks operating throughout the territory of Slovenia. With the help of the PHARE financing program and in close cooperation with the Environmental agency of RS the upgrade of the existing network begun in 2005 and was finished in March 2006. The upgrade provided new measuring sites with all relevant data needed in case of a radiological accident. Even bigger improvement was made in the area of data presentation and analysis, which was the main shortcoming of the old system. (author)

  9. Length Scales in Bayesian Automatic Adaptive Quadrature

    Directory of Open Access Journals (Sweden)

    Adam Gh.

    2016-01-01

    Full Text Available Two conceptual developments in the Bayesian automatic adaptive quadrature approach to the numerical solution of one-dimensional Riemann integrals [Gh. Adam, S. Adam, Springer LNCS 7125, 1–16 (2012] are reported. First, it is shown that the numerical quadrature which avoids the overcomputing and minimizes the hidden floating point loss of precision asks for the consideration of three classes of integration domain lengths endowed with specific quadrature sums: microscopic (trapezoidal rule, mesoscopic (Simpson rule, and macroscopic (quadrature sums of high algebraic degrees of precision. Second, sensitive diagnostic tools for the Bayesian inference on macroscopic ranges, coming from the use of Clenshaw-Curtis quadrature, are derived.

  10. Two Systems for Automatic Music Genre Recognition

    DEFF Research Database (Denmark)

    Sturm, Bob L.

    2012-01-01

    We re-implement and test two state-of-the-art systems for automatic music genre classification; but unlike past works in this area, we look closer than ever before at their behavior. First, we look at specific instances where each system consistently applies the same wrong label across multiple...... trials of cross-validation. Second, we test the robustness of each system to spectral equalization. Finally, we test how well human subjects recognize the genres of music excerpts composed by each system to be highly genre representative. Our results suggest that neither high-performing system has...... a capacity to recognize music genre....

  11. Automatic Tool for Local Assembly Structures

    Energy Technology Data Exchange (ETDEWEB)

    2016-10-11

    Whole community shotgun sequencing of total DNA (i.e. metagenomics) and total RNA (i.e. metatranscriptomics) has provided a wealth of information in the microbial community structure, predicted functions, metabolic networks, and is even able to reconstruct complete genomes directly. Here we present ATLAS (Automatic Tool for Local Assembly Structures) a comprehensive pipeline for assembly, annotation, genomic binning of metagenomic and metatranscriptomic data with an integrated framework for Multi-Omics. This will provide an open source tool for the Multi-Omic community at large.

  12. Length Scales in Bayesian Automatic Adaptive Quadrature

    Science.gov (United States)

    Adam, Gh.; Adam, S.

    2016-02-01

    Two conceptual developments in the Bayesian automatic adaptive quadrature approach to the numerical solution of one-dimensional Riemann integrals [Gh. Adam, S. Adam, Springer LNCS 7125, 1-16 (2012)] are reported. First, it is shown that the numerical quadrature which avoids the overcomputing and minimizes the hidden floating point loss of precision asks for the consideration of three classes of integration domain lengths endowed with specific quadrature sums: microscopic (trapezoidal rule), mesoscopic (Simpson rule), and macroscopic (quadrature sums of high algebraic degrees of precision). Second, sensitive diagnostic tools for the Bayesian inference on macroscopic ranges, coming from the use of Clenshaw-Curtis quadrature, are derived.

  13. Automatic code generation for distributed robotic systems

    International Nuclear Information System (INIS)

    Jones, J.P.

    1993-01-01

    Hetero Helix is a software environment which supports relatively large robotic system development projects. The environment supports a heterogeneous set of message-passing LAN-connected common-bus multiprocessors, but the programming model seen by software developers is a simple shared memory. The conceptual simplicity of shared memory makes it an extremely attractive programming model, especially in large projects where coordinating a large number of people can itself become a significant source of complexity. We present results from three system development efforts conducted at Oak Ridge National Laboratory over the past several years. Each of these efforts used automatic software generation to create 10 to 20 percent of the system

  14. Automatic blood detection in capsule endoscopy video

    Science.gov (United States)

    Novozámský, Adam; Flusser, Jan; Tachecí, Ilja; Sulík, Lukáš; Bureš, Jan; Krejcar, Ondřej

    2016-12-01

    We propose two automatic methods for detecting bleeding in wireless capsule endoscopy videos of the small intestine. The first one uses solely the color information, whereas the second one incorporates the assumptions about the blood spot shape and size. The original idea is namely the definition of a new color space that provides good separability of blood pixels and intestinal wall. Both methods can be applied either individually or their results can be fused together for the final decision. We evaluate their individual performance and various fusion rules on real data, manually annotated by an endoscopist.

  15. Personality in speech assessment and automatic classification

    CERN Document Server

    Polzehl, Tim

    2015-01-01

    This work combines interdisciplinary knowledge and experience from research fields of psychology, linguistics, audio-processing, machine learning, and computer science. The work systematically explores a novel research topic devoted to automated modeling of personality expression from speech. For this aim, it introduces a novel personality assessment questionnaire and presents the results of extensive labeling sessions to annotate the speech data with personality assessments. It provides estimates of the Big 5 personality traits, i.e. openness, conscientiousness, extroversion, agreeableness, and neuroticism. Based on a database built on the questionnaire, the book presents models to tell apart different personality types or classes from speech automatically.

  16. Automatic Planning of External Search Engine Optimization

    Directory of Open Access Journals (Sweden)

    Vita Jasevičiūtė

    2015-07-01

    Full Text Available This paper describes an investigation of the external search engine optimization (SEO action planning tool, dedicated to automatically extract a small set of most important keywords for each month during whole year period. The keywords in the set are extracted accordingly to external measured parameters, such as average number of searches during the year and for every month individually. Additionally the position of the optimized web site for each keyword is taken into account. The generated optimization plan is similar to the optimization plans prepared manually by the SEO professionals and can be successfully used as a support tool for web site search engine optimization.

  17. Automatic titrator for high precision plutonium assay

    International Nuclear Information System (INIS)

    Jackson, D.D.; Hollen, R.M.

    1986-01-01

    Highly precise assay of plutonium metal is required for accountability measurements. We have developed an automatic titrator for this determination which eliminates analyst bias and requires much less analyst time. The analyst is only required to enter sample data and start the titration. The automated instrument titrates the sample, locates the end point, and outputs the results as a paper tape printout. Precision of the titration is less than 0.03% relative standard deviation for a single determination at the 250-mg plutonium level. The titration time is less than 5 min

  18. Automatic Frequency Controller for Power Amplifiers Used in Bio-Implanted Applications: Issues and Challenges

    Directory of Open Access Journals (Sweden)

    Mahammad A. Hannan

    2014-12-01

    Full Text Available With the development of communication technologies, the use of wireless systems in biomedical implanted devices has become very useful. Bio-implantable devices are electronic devices which are used for treatment and monitoring brain implants, pacemakers, cochlear implants, retinal implants and so on. The inductive coupling link is used to transmit power and data between the primary and secondary sides of the biomedical implanted system, in which efficient power amplifier is very much needed to ensure the best data transmission rates and low power losses. However, the efficiency of the implanted devices depends on the circuit design, controller, load variation, changes of radio frequency coil’s mutual displacement and coupling coefficients. This paper provides a comprehensive survey on various power amplifier classes and their characteristics, efficiency and controller techniques that have been used in bio-implants. The automatic frequency controller used in biomedical implants such as gate drive switching control, closed loop power control, voltage controlled oscillator, capacitor control and microcontroller frequency control have been explained. Most of these techniques keep the resonance frequency stable in transcutaneous power transfer between the external coil and the coil implanted inside the body. Detailed information including carrier frequency, power efficiency, coils displacement, power consumption, supplied voltage and CMOS chip for the controllers techniques are investigated and summarized in the provided tables. From the rigorous review, it is observed that the existing automatic frequency controller technologies are more or less can capable of performing well in the implant devices; however, the systems are still not up to the mark. Accordingly, current challenges and problems of the typical automatic frequency controller techniques for power amplifiers are illustrated, with a brief suggestions and discussion section concerning

  19. Automatic ultrasound image enhancement for 2D semi-automatic breast-lesion segmentation

    Science.gov (United States)

    Lu, Kongkuo; Hall, Christopher S.

    2014-03-01

    Breast cancer is the fastest growing cancer, accounting for 29%, of new cases in 2012, and second leading cause of cancer death among women in the United States and worldwide. Ultrasound (US) has been used as an indispensable tool for breast cancer detection/diagnosis and treatment. In computer-aided assistance, lesion segmentation is a preliminary but vital step, but the task is quite challenging in US images, due to imaging artifacts that complicate detection and measurement of the suspect lesions. The lesions usually present with poor boundary features and vary significantly in size, shape, and intensity distribution between cases. Automatic methods are highly application dependent while manual tracing methods are extremely time consuming and have a great deal of intra- and inter- observer variability. Semi-automatic approaches are designed to counterbalance the advantage and drawbacks of the automatic and manual methods. However, considerable user interaction might be necessary to ensure reasonable segmentation for a wide range of lesions. This work proposes an automatic enhancement approach to improve the boundary searching ability of the live wire method to reduce necessary user interaction while keeping the segmentation performance. Based on the results of segmentation of 50 2D breast lesions in US images, less user interaction is required to achieve desired accuracy, i.e. live-wire segmentation.

  20. Automatic system for detecting pornographic images

    Science.gov (United States)

    Ho, Kevin I. C.; Chen, Tung-Shou; Ho, Jun-Der

    2002-09-01

    Due to the dramatic growth of network and multimedia technology, people can more easily get variant information by using Internet. Unfortunately, it also makes the diffusion of illegal and harmful content much easier. So, it becomes an important topic for the Internet society to protect and safeguard Internet users from these content that may be encountered while surfing on the Net, especially children. Among these content, porno graphs cause more serious harm. Therefore, in this study, we propose an automatic system to detect still colour porno graphs. Starting from this result, we plan to develop an automatic system to search porno graphs or to filter porno graphs. Almost all the porno graphs possess one common characteristic that is the ratio of the size of skin region and non-skin region is high. Based on this characteristic, our system first converts the colour space from RGB colour space to HSV colour space so as to segment all the possible skin-colour regions from scene background. We also apply the texture analysis on the selected skin-colour regions to separate the skin regions from non-skin regions. Then, we try to group the adjacent pixels located in skin regions. If the ratio is over a given threshold, we can tell if the given image is a possible porno graph. Based on our experiment, less than 10% of non-porno graphs are classified as pornography, and over 80% of the most harmful porno graphs are classified correctly.

  1. Norms concerning the programmable automatic control devices

    International Nuclear Information System (INIS)

    Fourmentraux, G.

    1995-01-01

    This presentation is a report of the studies carried out by the Work Group on Functioning Safety of Programmable Automatic Control Devices and by the Group for Prevention Studies (GEP) from the CEA. The objective of these groups is to evaluate the methods which could be used to estimate the functioning safety of control and instrumentation systems involved in the Important Elements for Safety (EIS) of the Basic Nuclear Installations (INB) of the CEA, and also to carry out a qualification of automatic control devices. Norms, protocols and tools for the evaluation are presented. The problem comprises two aspects: the evaluation of fault avoidance techniques and the evaluation of fault control techniques used during the conceiving. For the fault avoidance techniques, the quality assurance organization, the environment tests, and the software quality plans are considered. For the fault control techniques, the different available tools and fault injection models are analysed. The results of an analysis carried out with the DEF.I tool from the National Institute for Research and Safety (INRS) are reported. (J.S.). 23 refs

  2. Improvement of automatic fish feeder machine design

    Science.gov (United States)

    Chui Wei, How; Salleh, S. M.; Ezree, Abdullah Mohd; Zaman, I.; Hatta, M. H.; Zain, B. A. Md; Mahzan, S.; Rahman, M. N. A.; Mahmud, W. A. W.

    2017-10-01

    Nation Plan of action for management of fishing is target to achieve an efficient, equitable and transparent management of fishing capacity in marine capture fisheries by 2018. However, several factors influence the fishery production and efficiency of marine system such as automatic fish feeder machine could be taken in consideration. Two latest fish feeder machines have been chosen as the reference for this study. Based on the observation, it has found that the both machine was made with heavy structure, low water and temperature resistance materials. This research’s objective is to develop the automatic feeder machine to increase the efficiency of fish feeding. The experiment has conducted to testing the new design of machine. The new machine with maximum storage of 5 kg and functioning with two DC motors. This machine able to distribute 500 grams of pellets within 90 seconds and longest distance of 4.7 meter. The higher speed could reduce time needed and increase the distance as well. The minimum speed range for both motor is 110 and 120 with same full speed range of 255.

  3. Automatic Lumbar Spondylolisthesis Measurement in CT Images.

    Science.gov (United States)

    Liao, Shu; Zhan, Yiqiang; Dong, Zhongxing; Yan, Ruyi; Gong, Liyan; Zhou, Xiang Sean; Salganicoff, Marcos; Fei, Jun

    2016-07-01

    Lumbar spondylolisthesis is one of the most common spinal diseases. It is caused by the anterior shift of a lumbar vertebrae relative to subjacent vertebrae. In current clinical practices, staging of spondylolisthesis is often conducted in a qualitative way. Although meyerding grading opens the door to stage spondylolisthesis in a more quantitative way, it relies on the manual measurement, which is time consuming and irreproducible. Thus, an automatic measurement algorithm becomes desirable for spondylolisthesis diagnosis and staging. However, there are two challenges. 1) Accurate detection of the most anterior and posterior points on the superior and inferior surfaces of each lumbar vertebrae. Due to the small size of the vertebrae, slight errors of detection may lead to significant measurement errors, hence, wrong disease stages. 2) Automatic localize and label each lumbar vertebrae is required to provide the semantic meaning of the measurement. It is difficult since different lumbar vertebraes have high similarity of both shape and image appearance. To resolve these challenges, a new auto measurement framework is proposed with two major contributions: First, a learning based spine labeling method that integrates both the image appearance and spine geometry information is designed to detect lumbar vertebrae. Second, a hierarchical method using both the population information from atlases and domain-specific information in the target image is proposed for most anterior and posterior points positioning. Validated on 258 CT spondylolisthesis patients, our method shows very similar results to manual measurements by radiologists and significantly increases the measurement efficiency.

  4. Automatic Door Access System Using Face Recognition

    Directory of Open Access Journals (Sweden)

    Hteik Htar Lwin

    2015-06-01

    Full Text Available Abstract Most doors are controlled by persons with the use of keys security cards password or pattern to open the door. Theaim of this paper is to help users forimprovement of the door security of sensitive locations by using face detection and recognition. Face is a complex multidimensional structure and needs good computing techniques for detection and recognition. This paper is comprised mainly of three subsystems namely face detection face recognition and automatic door access control. Face detection is the process of detecting the region of face in an image. The face is detected by using the viola jones method and face recognition is implemented by using the Principal Component Analysis PCA. Face Recognition based on PCA is generally referred to as the use of Eigenfaces.If a face is recognized it is known else it is unknown. The door will open automatically for the known person due to the command of the microcontroller. On the other hand alarm will ring for the unknown person. Since PCA reduces the dimensions of face images without losing important features facial images for many persons can be stored in the database. Although many training images are used computational efficiency cannot be decreased significantly. Therefore face recognition using PCA can be more useful for door security system than other face recognition schemes.

  5. Towards Automatic Decentralized Control Structure Selection

    DEFF Research Database (Denmark)

    A subtask in integration of design and control of chemical processes is the selection of a control structure. Automating the selection of the control structure enables sequential integration of process and controld esign. As soon as the process is specified or computed, a structure for decentrali......A subtask in integration of design and control of chemical processes is the selection of a control structure. Automating the selection of the control structure enables sequential integration of process and controld esign. As soon as the process is specified or computed, a structure...... for decentralized control is determined automatically, and the resulting decentralized control structure is automatically tuned using standard techniques. Dynamic simulation of the resulting process system gives immediate feedback to the process design engineer regarding practical operability of the process....... The control structure selection problem is formulated as a special MILP employing cost coefficients which are computed using Parseval's theorem combined with RGA and IMC concepts. This approach enables selection and tuning of large-scale plant-wide decentralized controllers through efficient combination...

  6. Towards Automatic Decentralized Control Structure Selection

    DEFF Research Database (Denmark)

    Jørgensen, John Bagterp; Jørgensen, Sten Bay

    2000-01-01

    A subtask in integration of design and control of chemical processes is the selection of a control structure. Automating the selection of the control structure enables sequential integration of process and control design. As soon as the process is specified or computed, a structure for decentrali......A subtask in integration of design and control of chemical processes is the selection of a control structure. Automating the selection of the control structure enables sequential integration of process and control design. As soon as the process is specified or computed, a structure...... for decentralized control is determined automatically, and the resulting decentralized control structure is automatically tuned using standard techniques. Dynamic simulation of the resulting process system gives immediate feedback to the process design engineer regarding practical operability of the process....... The control structure selection problem is formulated as a special MILP employing cost coefficients which are computed using Parseval's theorem combined with RGA and IMC concepts. This approach enables selection and tuning of large-scale plant-wide decentralized controllers through efficient combination...

  7. Automatic Feature Extraction from Planetary Images

    Science.gov (United States)

    Troglio, Giulia; Le Moigne, Jacqueline; Benediktsson, Jon A.; Moser, Gabriele; Serpico, Sebastiano B.

    2010-01-01

    With the launch of several planetary missions in the last decade, a large amount of planetary images has already been acquired and much more will be available for analysis in the coming years. The image data need to be analyzed, preferably by automatic processing techniques because of the huge amount of data. Although many automatic feature extraction methods have been proposed and utilized for Earth remote sensing images, these methods are not always applicable to planetary data that often present low contrast and uneven illumination characteristics. Different methods have already been presented for crater extraction from planetary images, but the detection of other types of planetary features has not been addressed yet. Here, we propose a new unsupervised method for the extraction of different features from the surface of the analyzed planet, based on the combination of several image processing techniques, including a watershed segmentation and the generalized Hough Transform. The method has many applications, among which image registration and can be applied to arbitrary planetary images.

  8. Automatic location of disruption times in JET.

    Science.gov (United States)

    Moreno, R; Vega, J; Murari, A

    2014-11-01

    The loss of stability and confinement in tokamak plasmas can induce critical events known as disruptions. Disruptions produce strong electromagnetic forces and thermal loads which can damage fundamental components of the devices. Determining the disruption time is extremely important for various disruption studies: theoretical models, physics-driven models, or disruption predictors. In JET, during the experimental campaigns with the JET-C (Carbon Fiber Composite) wall, a common criterion to determine the disruption time consisted of locating the time of the thermal quench. However, with the metallic ITER-like wall (JET-ILW), this criterion is usually not valid. Several thermal quenches may occur previous to the current quench but the temperature recovers. Therefore, a new criterion has to be defined. A possibility is to use the start of the current quench as disruption time. This work describes the implementation of an automatic data processing method to estimate the disruption time according to this new definition. This automatic determination allows both reducing human efforts to locate the disruption times and standardizing the estimates (with the benefit of being less vulnerable to human errors).

  9. Refining Automatically Extracted Knowledge Bases Using Crowdsourcing.

    Science.gov (United States)

    Li, Chunhua; Zhao, Pengpeng; Sheng, Victor S; Xian, Xuefeng; Wu, Jian; Cui, Zhiming

    2017-01-01

    Machine-constructed knowledge bases often contain noisy and inaccurate facts. There exists significant work in developing automated algorithms for knowledge base refinement. Automated approaches improve the quality of knowledge bases but are far from perfect. In this paper, we leverage crowdsourcing to improve the quality of automatically extracted knowledge bases. As human labelling is costly, an important research challenge is how we can use limited human resources to maximize the quality improvement for a knowledge base. To address this problem, we first introduce a concept of semantic constraints that can be used to detect potential errors and do inference among candidate facts. Then, based on semantic constraints, we propose rank-based and graph-based algorithms for crowdsourced knowledge refining, which judiciously select the most beneficial candidate facts to conduct crowdsourcing and prune unnecessary questions. Our experiments show that our method improves the quality of knowledge bases significantly and outperforms state-of-the-art automatic methods under a reasonable crowdsourcing cost.

  10. Fully automatic CNC machining production system

    Directory of Open Access Journals (Sweden)

    Lee Jeng-Dao

    2017-01-01

    Full Text Available Customized manufacturing is increasing years by years. The consumption habits change has been cause the shorter of product life cycle. Therefore, many countries view industry 4.0 as a target to achieve more efficient and more flexible automated production. To develop an automatic loading and unloading CNC machining system via vision inspection is the first step in industrial upgrading. CNC controller is adopted as the main controller to command to the robot, conveyor, and other equipment in this study. Moreover, machine vision systems are used to detect position of material on the conveyor and the edge of the machining material. In addition, Open CNC and SCADA software will be utilized to make real-time monitor, remote system of control, alarm email notification, and parameters collection. Furthermore, RFID has been added to employee classification and management. The machine handshaking has been successfully proposed to achieve automatic vision detect, edge tracing measurement, machining and system parameters collection for data analysis to accomplish industrial automation system integration with real-time monitor.

  11. Automatic target identification using neural networks

    Science.gov (United States)

    Abdallah, Mahmoud A.; Samu, Tayib I.; Grissom, William A.

    1995-10-01

    Neural network theories are applied to attain human-like performance in areas such as speech recognition, statistical mapping, and target recognition or identification. In target identification, one of the difficult tasks has been the extraction of features to be used to train the neural network which is subsequently used for the target's identification. The purpose of this paper is to describe the development of an automatic target identification system using features extracted from a specific class of targets. The extracted features were the graphical representations of the silhouettes of the targets. Image processing techniques and some Fast Fourier Transform (FFT) properties were implemented to extract the features. The FFT eliminates variations in the extracted features due to rotation or scaling. A Neural Network was trained with the extracted features using the Learning Vector Quantization paradigm. An identification system was set up to test the algorithm. The image processing software was interfaced with MATLAB Neural Network Toolbox via a computer program written in C language to automate the target identification process. The system performed well as at classified the objects used to train it irrespective of rotation, scaling, and translation. This automatic target identification system had a classification success rate of about 95%.

  12. Automatic design of digital synthetic gene circuits.

    Directory of Open Access Journals (Sweden)

    Mario A Marchisio

    2011-02-01

    Full Text Available De novo computational design of synthetic gene circuits that achieve well-defined target functions is a hard task. Existing, brute-force approaches run optimization algorithms on the structure and on the kinetic parameter values of the network. However, more direct rational methods for automatic circuit design are lacking. Focusing on digital synthetic gene circuits, we developed a methodology and a corresponding tool for in silico automatic design. For a given truth table that specifies a circuit's input-output relations, our algorithm generates and ranks several possible circuit schemes without the need for any optimization. Logic behavior is reproduced by the action of regulatory factors and chemicals on the promoters and on the ribosome binding sites of biological Boolean gates. Simulations of circuits with up to four inputs show a faithful and unequivocal truth table representation, even under parametric perturbations and stochastic noise. A comparison with already implemented circuits, in addition, reveals the potential for simpler designs with the same function. Therefore, we expect the method to help both in devising new circuits and in simplifying existing solutions.

  13. Anti-Theft Automatic Metering Interface

    Directory of Open Access Journals (Sweden)

    Abhijeet Das

    2015-08-01

    Full Text Available Abstract Electricity is now more than a necessity and its need is increasing day by day resulting in power theft and power scarcity. The purpose of this project is to provide automatic control and monitoring of the Domestic Energy Meter enabling the Electricity Department to read meter readings without anyone visiting each house and also prevent electricity theft .This can be achieved by the use of a Microcontroller Unit that continuously monitors and records the Energy Meter readings in its permanent memory location. This system also makes use of a GSM module for remote monitoring and control of Energy Meter with the help of an interfacing circuitry. The Microcontroller based system continuously records the readings and the live meter reading can be sent to the Electricity department after a count period or on request. This system also can be used to disconnect the power supply to the house in case of non-payment of electricity bills. The Substation will be the receiving end. The data received is fed to a microcontroller at the Substation which will automatically calculate the bill based on tariff provider and display it.

  14. SET UP OF THE NEW AUTOMATIC HYDROMETEOROLOGICAL NETWORK IN HUNGARY

    Directory of Open Access Journals (Sweden)

    J. NAGy

    2013-03-01

    Full Text Available The Hungarian Meteorological Service (OMSZ and General Directorate of Water Management (OVF in Hungary run conventional precipitation measurement networks consisting of at least 1000 stations. OMSZ automated its synoptic and climatological network in 90’s and now more than 100 automatic stations give data every 1-10 minutes via GPRS channel. In 2007 the experts from both institutions determined the requirements of a common network. The predecessor in title of OVF is general Directorate for Water and Environment gave a project proposal in 2008 for establishment of a new hydrometeorological network based on common aims for meteorology and hydrology. The new hydrometeorological network was set up in 2012 financed by KEOP project. This network has got 141 weighing precipitation gauges, 118 temperature - humidity sensors and 25 soil moisture and soil temperature instruments. Near by Tisza-Lake two wind sensors have been installed. The network is operated by OMSZ and OVF together. OVF and its institutions maintain the stations itself and support the electricity. OMSZ operates data collection and transmission, maintaines and calibrates the sensors. Using precipitation data of enhanced network the radar precipitation field quality may be more precise, which are input of run-off model. Thereby the time allowance may be increased in flood-control events. Based on soil moisture and temperature water balance in soil may be modelled and forecast can be produced in different conditions. It is very important task in drought and inland water conditions. Considering OMSZ investment project in which new Doppler dual polarisation radar and 14 disdrometers will be installed, the precipitation estimation may be improved since 2015.

  15. Automatic first-break picking using the instantaneous traveltime attribute

    KAUST Repository

    Saragiotis, Christos

    2012-01-01

    Picking the first breaks is an important step in seismic processing. The large volume of the seismic data calls for automatic and objective picking. We introduce a new automatic first-break picker, which uses specifically designed time windows and an iterative procedure based on the instantaneous traveltime attribute. The method is fast as it only uses a few FFT\\'s per trace. We demonstrate the effectiveness of this automatic method by applying it on real test data.

  16. 2nd International Conference on Mechatronics and Automatic Control

    CERN Document Server

    2015-01-01

    This book examines mechatronics and automatic control systems. The book covers important emerging topics in signal processing, control theory, sensors, mechanic manufacturing systems and automation. The book presents papers from the second International Conference on Mechatronics and Automatic Control Systems held in Beijing, China on September 20-21, 2014. Examines how to improve productivity through the latest advanced technologies Covering new systems and techniques in the broad field of mechatronics and automatic control systems.

  17. Plasmodium vivax Transmission in Africa.

    Directory of Open Access Journals (Sweden)

    Rosalind E Howes

    2015-11-01

    Full Text Available Malaria in sub-Saharan Africa has historically been almost exclusively attributed to Plasmodium falciparum (Pf. Current diagnostic and surveillance systems in much of sub-Saharan Africa are not designed to identify or report non-Pf human malaria infections accurately, resulting in a dearth of routine epidemiological data about their significance. The high prevalence of Duffy negativity provided a rationale for excluding the possibility of Plasmodium vivax (Pv transmission. However, review of varied evidence sources including traveller infections, community prevalence surveys, local clinical case reports, entomological and serological studies contradicts this viewpoint. Here, these data reports are weighted in a unified framework to reflect the strength of evidence of indigenous Pv transmission in terms of diagnostic specificity, size of individual reports and corroboration between evidence sources. Direct evidence was reported from 21 of the 47 malaria-endemic countries studied, while 42 countries were attributed with infections of visiting travellers. Overall, moderate to conclusive evidence of transmission was available from 18 countries, distributed across all parts of the continent. Approximately 86.6 million Duffy positive hosts were at risk of infection in Africa in 2015. Analysis of the mechanisms sustaining Pv transmission across this continent of low frequency of susceptible hosts found that reports of Pv prevalence were consistent with transmission being potentially limited to Duffy positive populations. Finally, reports of apparent Duffy-independent transmission are discussed. While Pv is evidently not a major malaria parasite across most of sub-Saharan Africa, the evidence presented here highlights its widespread low-level endemicity. An increased awareness of Pv as a potential malaria parasite, coupled with policy shifts towards species-specific diagnostics and reporting, will allow a robust assessment of the public health

  18. Transmission pricing: paradigms and methodologies

    Energy Technology Data Exchange (ETDEWEB)

    Shirmohammadi, Dariush [Pacific Gas and Electric Co., San Francisco, CA (United States); Vieira Filho, Xisto; Gorenstin, Boris [Centro de Pesquisas de Energia Eletrica (CEPEL), Rio de Janeiro, RJ (Brazil); Pereira, Mario V.P. [Power System Research, Rio de Janeiro, RJ (Brazil)

    1994-12-31

    In this paper we describe the principles of several paradigms and methodologies for pricing transmission services. The paper outlines some of the main characteristics of these paradigms and methodologies such as where they may be used for best results. Due to their popularity, power flow based MW-mile and short run marginal cost pricing methodologies will be covered in some detail. We conclude the paper with examples of the application of these two pricing methodologies for pricing transmission services in Brazil. (author) 25 refs., 2 tabs.

  19. Microwave power transmission by satellites

    Science.gov (United States)

    Keydel, W.

    The MPTS (microwave power transmission system) is examined with regard to the problems involved, the proposed solutions, the future outlook, and the necessity for further work. The MPTS is analyzed with regard to system considerations, design considerations (power transmission, frequency selection, power generation, the spacetenna, microwave propagation problems, the rectenna, and efficiency), environmental impacts (electromagnetic compatibility and RF interference, and health and ecological effects). It is concluded that the MPTS is feasible, but that further studies are needed to optimize the system with respect to such factors as efficiency and environmental impact.

  20. Electromagnetic Transmission Through Resonant Structures

    Science.gov (United States)

    Young, Steven M.

    Electromagnetic resonators store energy in the form of oscillatory electric and magnetic fields and gradually exchange that energy by coupling with their environment. This coupling process can have profound effects on the transmission and reflection properties of nearby interfaces, with rapid transitions from high transmittance to high reflectance over narrow frequency ranges, and has been exploited to design useful optical components such as spectral filters and dielectric mirrors. This dissertation includes analytic, numeric, and experimental investigations of three different electromagnetic resonators, each based on a different method of confining electromagnetic fields near the region of interest. First, we show that a structure with two parallel conducting plates, each containing a subwavelength slit, supports a localized resonant mode bound to the slits and therefore exhibits (in the absence of nonradiative losses), perfect resonant transmission over a narrow frequency range. In practice, the transmission is limited by conduction losses in the sidewalls; nevertheless, experimental results at 10 GHz show a narrowband transmission enhancement by a factor of 104 compared to the non-resonant transmission, with quality factor (ratio of frequency to peak width) Q ~ 3000. Second, we describe a narrowband transmission filter based on a single-layer dielectric grating. We use a group theory analysis to show that, due to their symmetry, several of the grating modes cannot couple to light at normal incidence, while several others have extremely large coupling. We then show how selectively breaking the system symmetry using off-normal light incidence can produce transmission peaks by enabling weak coupling to some of the previously protected modes. The narrowband filtering capabilities are validated by an experimental demonstration in the long wavelength infrared, showing transmission peaks of quality factor Q ~ 100 within a free-spectral range of 8-15 mum. Third, we

  1. Topics in lightwave transmission systems

    CERN Document Server

    Li, Tingye

    1991-01-01

    Topics in Lightwave Transmission Systems is a second volume of a treatise on optical fiber communications that is devoted to the science, engineering, and application of information transmission via optical fibers. The first volume, published in 1985, dealt exclusively with fiber fabrication. The present volume contains topics that pertain to subsystems and systems. The book contains five chapters and begins with discussions of transmitters and receivers, which are basic to systems now operating in the field. Subsequent chapters cover topics relating to coherent systems: frequency and phase m

  2. Automatic Clustering Using FSDE-Forced Strategy Differential Evolution

    Science.gov (United States)

    Yasid, A.

    2018-01-01

    Clustering analysis is important in datamining for unsupervised data, cause no adequate prior knowledge. One of the important tasks is defining the number of clusters without user involvement that is known as automatic clustering. This study intends on acquiring cluster number automatically utilizing forced strategy differential evolution (AC-FSDE). Two mutation parameters, namely: constant parameter and variable parameter are employed to boost differential evolution performance. Four well-known benchmark datasets were used to evaluate the algorithm. Moreover, the result is compared with other state of the art automatic clustering methods. The experiment results evidence that AC-FSDE is better or competitive with other existing automatic clustering algorithm.

  3. Automatic measuring device for atomic oxygen concentrations (1962)

    International Nuclear Information System (INIS)

    Weill, J.; Deiss, M.; Mercier, R.

    1962-01-01

    Within the framework of the activities of the Autonomous Reactor Electronics Section we have developed a device, which renders automatic one type of measurement carried out in the Physical Chemistry Department at the Saclay Research Centre. We define here: - the physico-chemical principle of the apparatus which is adapted to the measurement of atomic oxygen concentrations; - the physical principle of the automatic measurement; - the properties, performance, constitution, use and maintenance of the automatic measurement device. It is concluded that the principle of the automatic device, whose tests have confirmed the estimation of the theoretical performance, could usefully be adapted to other types of measurement. (authors) [fr

  4. Laboratory Automatic Titration of Chromium Plating and Electropolishing Solutions

    National Research Council Canada - National Science Library

    Sopok, Samuel

    2001-01-01

    .... The analytical chemistry literature lacks an adequate automatic titration method for the monitoring of chromic acid in chromium plating solutions and the monitoring of phosphoric and sulfuric acids...

  5. Design and control of electromagnetic clutch actuation system for automated manual transmission

    Science.gov (United States)

    Ranjan, Ashish; Prasanth, S.; Cherian, Fenin; Baskar, P.

    2017-11-01

    There is a growing interest towards Automatic Transmission in India as it provides better comfort and drivability. But the high cost of this system is limiting itself to be successful in the Indian markets. Due to this, Automated Manual Transmission (AMT) is considered which provides a better solution towards automation as it enhances the drivability and fuel consumption characteristics of a manual transmission at lower costs. However, torque lag and comfort are major issues with AMT which can be addressed by reducing the shift time. In this paper we describe an Electromagnetic Linear Clutch Actuator as a replacement to current electrohydraulic and electromechanical actuator. A control system for the actuator is presented and a clutch engagement strategy is also implemented which reduces the engagement time to 0.78 seconds while reducing jerk and torque lag. The actuator and control system is simulated on a MATLAB Simulink and agreeable results have been obtained.

  6. To render time sensible: transmissibility

    Directory of Open Access Journals (Sweden)

    Jae Emerling

    2015-12-01

    Full Text Available This review-essay of Keith Moxey’s Visual Time: The Image in History (2013 addresses recent theoretical work on images, historiography, and temporality. It does so by critiquing preexisting methodological issues such as linear chronology, ekphrasis, and contemporaneity. In addition to reviewing how Moxey deals with the problematic of temporality in art historical practice, this review-essay develops its own methodological approach through the concept of transmissibility. Transmissibility is a theoretical methodology for how to approach the relation between temporality and artworks that draws on the work of Gilles Deleuze and Félix Guattari. Transmissibility stems from a desire to arrive at an art history capable of articulating the complex epistemic and aesthetic power of an artwork. In other words, an artwork as a material, expressive reality, a conjunction of content and expression, statement and visibility, sensible and intelligible. It remains to us as art historians to think a philosophy of history wherein artworks embody transmissibility (survival, anachronism, memory, becoming: the full complexity of temporality.

  7. Solution of the Transmission Problem

    Czech Academy of Sciences Publication Activity Database

    Medková, Dagmar

    2010-01-01

    Roč. 110, č. 3 (2010), s. 1489-1500 ISSN 0167-8019 Institutional research plan: CEZ:AV0Z10190503 Keywords : Laplace equation * transmission problem * single layer potential * double layer potential Subject RIV: BA - General Mathematics Impact factor: 0.979, year: 2010 http://link.springer.com/article/10.1007%2Fs10440-009-9522-5

  8. Downlink Transmission of Short Packets

    DEFF Research Database (Denmark)

    Trillingsgaard, Kasper Fløe; Popovski, Petar

    2017-01-01

    the principles of frame design and show the impact of the new design in scenarios that feature short data packets, which are central to various 5G and Internet of Things applications. We~treat framing for downlink transmission in an AWGN broadcast channel with $K$ users, where the sizes of the messages...

  9. Money and transmission of bacteria.

    NARCIS (Netherlands)

    Gedik, H.; Voss, T.A.; Voss, A.

    2013-01-01

    Money is one of the most frequently passed items in the world. The aim of this study was to ascertain the survival status of bacteria including Staphylococcus aureus, Escherichia coli, and Vancomycin- Resistant Enterococci (VRE) on banknotes from different countries and the transmission of bacteria

  10. Transmission electron microscopy of bone

    NARCIS (Netherlands)

    Everts, Vincent; Niehof, Anneke; Tigchelaar-Gutter, Wikky; Beertsen, Wouter

    2012-01-01

    This chapter describes procedures to process mineralized tissues obtained from different sources for transmission electron microscopy (TEM). Methods for fixation, resin embedding, staining of semi-thin sections and ultrathin sections are presented. In addition, attention will be paid to processing

  11. Automaticity: design of a registry to assess long-term acceptance and clinical impact of Automatic Algorithms in Insignia pacemakers.

    Science.gov (United States)

    Alings, Marco; Vorstenbosch, Jan-Mark; Reeve, Helen

    2009-03-01

    Worldwide, the number of implants of pacemakers is steadily increasing and this poses an incremental burden on outpatient clinics. While device manufacturers have developed safe and effective automatic algorithms to lighten this workload, the clinical utilization of these algorithms has not been well studied. The Automaticity study is the first large-scale, worldwide registry to evaluate physician's acceptance of automatic algorithms for ventricular capture, automatic sensing, and automatic optimization of sensor settings. The primary objective of the registry is to determine the percentage of patients who have any of the 'Automaticity Algorithms' reprogrammed within 12 months of pacemaker implant. Patients will be implanted with a commercially available pacemaker (Insignia I/Nexus I Ultra or Insignia I/Nexus I AVT, Boston Scientific CRM, St Paul, MN, USA). At discharge, all the 'Automaticity Algorithms' are to be programmed to 'Auto/On'. Data collection on changes in device programming, physician's perception of algorithm function, and adverse events will occur for 12 months following device implant. The Automaticity study is the first large-scale, prospective, multi-site, international registry designed to assess the long-term acceptance of automatic pacemaker algorithms for adjustment of the ventricular output, atrial and ventricular sensitivity, and optimization of minute ventilation and accelerometer settings.

  12. Real time automatic discriminating of ultrasonic flaws

    International Nuclear Information System (INIS)

    Suhairy Sani; Mohd Hanif Md Saad; Marzuki Mustafa; Mohd Redzwan Rosli

    2009-01-01

    This paper is concerned with the real time automatic discriminating of flaws from two categories; i. cracks (planar defect) and ii. Non-cracks (volumetric defect such as cluster porosity and slag) using pulse-echo ultrasound. The raw ultrasonic flaws signal were collected from a computerized robotic plane scanning system over the whole of each reflector as the primary source of data. The signal is then filtered and the analysis in both time and frequency domain were executed to obtain the selected feature. The real time feature analysis techniques measured the number of peaks, maximum index, pulse duration, rise time and fall time. The obtained features could be used to distinguish between quantitatively classified flaws by using various tools in artificial intelligence such as neural networks. The proposed algorithm and complete system were implemented in a computer software developed using Microsoft Visual BASIC 6.0 (author)

  13. Automatic Phonetic Transcription for Danish Speech Recognition

    DEFF Research Database (Denmark)

    Kirkedal, Andreas Søeborg

    Automatic speech recognition (ASR) uses dictionaries that map orthographic words to their phonetic representation. To minimize the occurrence of out-of-vocabulary words, ASR requires large phonetic dictionaries to model pronunciation. Hand-crafted high-quality phonetic dictionaries are difficult...... for particular words and word classes in addition. In comparison, English has 5,852 spelling-tophoneme rules and 4,133 additional rules and 8,278 rules and 3,829 additional rules. Phonix applies deep morphological analysis as a preprocessing step. Should the analysis fail, several fallback strategies...... to dictionary lookup, compound splitting and letter-to-sound rules. Phonix and eSpeak will be compared in an ASR scenario using the Kaldi speech recognition toolkit (Povey et al., 2011) and compared to a graphemic baseline. Also a mapping between the phonetic alphabets, which are both based on X-Sampa or IPA...

  14. Image based automatic water meter reader

    Science.gov (United States)

    Jawas, N.; Indrianto

    2018-01-01

    Water meter is used as a tool to calculate water consumption. This tool works by utilizing water flow and shows the calculation result with mechanical digit counter. Practically, in everyday use, an operator will manually check the digit counter periodically. The Operator makes logs of the number shows by water meter to know the water consumption. This manual operation is time consuming and prone to human error. Therefore, in this paper we propose an automatic water meter digit reader from digital image. The digits sequence is detected by utilizing contour information of the water meter front panel.. Then an OCR method is used to get the each digit character. The digit sequence detection is an important part of overall process. It determines the success of overall system. The result shows promising results especially in sequence detection.

  15. Image-based automatic recognition of larvae

    Science.gov (United States)

    Sang, Ru; Yu, Guiying; Fan, Weijun; Guo, Tiantai

    2010-08-01

    As the main objects, imagoes have been researched in quarantine pest recognition in these days. However, pests in their larval stage are latent, and the larvae spread abroad much easily with the circulation of agricultural and forest products. It is presented in this paper that, as the new research objects, larvae are recognized by means of machine vision, image processing and pattern recognition. More visional information is reserved and the recognition rate is improved as color image segmentation is applied to images of larvae. Along with the characteristics of affine invariance, perspective invariance and brightness invariance, scale invariant feature transform (SIFT) is adopted for the feature extraction. The neural network algorithm is utilized for pattern recognition, and the automatic identification of larvae images is successfully achieved with satisfactory results.

  16. Automatic feed system for ultrasonic machining

    Science.gov (United States)

    Calkins, Noel C.

    1994-01-01

    Method and apparatus for ultrasonic machining in which feeding of a tool assembly holding a machining tool toward a workpiece is accomplished automatically. In ultrasonic machining, a tool located just above a workpiece and vibrating in a vertical direction imparts vertical movement to particles of abrasive material which then remove material from the workpiece. The tool does not contact the workpiece. Apparatus for moving the tool assembly vertically is provided such that it operates with a relatively small amount of friction. Adjustable counterbalance means is provided which allows the tool to be immobilized in its vertical travel. A downward force, termed overbalance force, is applied to the tool assembly. The overbalance force causes the tool to move toward the workpiece as material is removed from the workpiece.

  17. Automatic female dehumanization across the menstrual cycle.

    Science.gov (United States)

    Piccoli, Valentina; Fantoni, Carlo; Foroni, Francesco; Bianchi, Mauro; Carnaghi, Andrea

    2017-06-01

    In this study, we investigate whether hormonal shifts during the menstrual cycle contribute to the dehumanization of other women and men. Female participants with different levels of likelihood of conception (LoC) completed a semantic priming paradigm in a lexical decision task. When the word 'woman' was the prime, animal words were more accessible in high versus low LoC whereas human words were more inhibited in the high versus low LoC. When the word 'man' was used as the prime, no difference was found in terms of accessibility between high and low LoC for either animal or human words. These results show that the female dehumanization is automatically elicited by menstrual cycle-related processes and likely associated with an enhanced activation of mate-attraction goals. © 2016 The British Psychological Society.

  18. Automatic Smoker Detection from Telephone Speech Signals

    DEFF Research Database (Denmark)

    Alavijeh, Amir Hossein Poorjam; Hesaraki, Soheila; Safavi, Saeid

    2017-01-01

    This paper proposes an automatic smoking habit detection from spontaneous telephone speech signals. In this method, each utterance is modeled using i-vector and non-negative factor analysis (NFA) frameworks, which yield low-dimensional representation of utterances by applying factor analysis...... on Gaussian mixture model means and weights respectively. Each framework is evaluated using different classification algorithms to detect the smoker speakers. Finally, score-level fusion of the i-vector-based and the NFA-based recognizers is considered to improve the classification accuracy. The proposed...... method is evaluated on telephone speech signals of speakers whose smoking habits are known drawn from the National Institute of Standards and Technology (NIST) 2008 and 2010 Speaker Recognition Evaluation databases. Experimental results over 1194 utterances show the effectiveness of the proposed approach...

  19. A System for Automatically Generating Scheduling Heuristics

    Science.gov (United States)

    Morris, Robert

    1996-01-01

    The goal of this research is to improve the performance of automated schedulers by designing and implementing an algorithm by automatically generating heuristics by selecting a schedule. The particular application selected by applying this method solves the problem of scheduling telescope observations, and is called the Associate Principal Astronomer. The input to the APA scheduler is a set of observation requests submitted by one or more astronomers. Each observation request specifies an observation program as well as scheduling constraints and preferences associated with the program. The scheduler employs greedy heuristic search to synthesize a schedule that satisfies all hard constraints of the domain and achieves a good score with respect to soft constraints expressed as an objective function established by an astronomer-user.

  20. An automatic molecular dispenser of chloride.

    Science.gov (United States)

    Alibrandi, Giuseppe; Amendola, Valeria; Bergamaschi, Greta; Dollenz, Riccardo; Fabbrizzi, Luigi; Licchelli, Maurizio; Lo Vecchio, Carmelo

    2013-03-11

    The combined activity of the 1.1.1-cryptand and of a dicopper(II) bistren cryptate complex including chloride makes the Cl(-) ion be continuously and slowly delivered to the solution, without any external intervention. The 1.1.1-cryptand slowly releases OH(-) ions, according to a defined kinetics, and each OH(-) ion displaces a Cl(-) ion from the cryptate. Chloride displacement induces a sharp colour change from bright yellow to aquamarine and can be conveniently monitored spectrophotometrically, even in diluted solutions. The 1.1.1-cryptand is the motor of a molecular dispenser (the dicopper(II) cryptate) delivering chloride ion automatically, from the inside of the solution. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  1. Human-competitive automatic topic indexing

    CERN Document Server

    Medelyan, Olena

    2009-01-01

    Topic indexing is the task of identifying the main topics covered by a document. These are useful for many purposes: as subject headings in libraries, as keywords in academic publications and as tags on the web. Knowing a document’s topics helps people judge its relevance quickly. However, assigning topics manually is labor intensive. This thesis shows how to generate them automatically in a way that competes with human performance. Three kinds of indexing are investigated: term assignment, a task commonly performed by librarians, who select topics from a controlled vocabulary; tagging, a popular activity of web users, who choose topics freely; and a new method of keyphrase extraction, where topics are equated to Wikipedia article names. A general two-stage algorithm is introduced that first selects candidate topics and then ranks them by significance based on their properties. These properties draw on statistical, semantic, domain-specific and encyclopedic knowledge. They are combined using a machine learn...

  2. Automatically Maintain Climatic Conditions inside Agricultural Greenhouses

    Directory of Open Access Journals (Sweden)

    Ali Jasim Ramadhan

    2016-11-01

    Full Text Available In this work, a novel system is designed to remote monitor / automatic control of the temperature, humidity and soil moisture of the agricultural greenhouses. In the proposed system, the author used the mentioned sensors for monitoring the climatic conditions of the agricultural greenhouses; and the system makes a controlling process to fix the required parameters for plant growth by running / stopping the fan, air exchanger and irrigation devices when any changes happened in these parameters. The presented system is based on XBee protocol in the implemented wireless sensor star topology network (WSN to monitor the agricultural greenhouses in real time, and used the GSM and Internet technologies to monitor the agricultural greenhouses from anywhere.

  3. Towards Automatic Classification of Wikipedia Content

    Science.gov (United States)

    Szymański, Julian

    Wikipedia - the Free Encyclopedia encounters the problem of proper classification of new articles everyday. The process of assignment of articles to categories is performed manually and it is a time consuming task. It requires knowledge about Wikipedia structure, which is beyond typical editor competence, which leads to human-caused mistakes - omitting or wrong assignments of articles to categories. The article presents application of SVM classifier for automatic classification of documents from The Free Encyclopedia. The classifier application has been tested while using two text representations: inter-documents connections (hyperlinks) and word content. The results of the performed experiments evaluated on hand crafted data show that the Wikipedia classification process can be partially automated. The proposed approach can be used for building a decision support system which suggests editors the best categories that fit new content entered to Wikipedia.

  4. Automatic measurement of target crossing speed

    Science.gov (United States)

    Wardell, Mark; Lougheed, James H.

    1992-11-01

    The motion of ground vehicle targets after a ballistic round is launched can be a major source of inaccuracy for small (handheld) anti-armour weapon systems. A method of automatically measuring the crossing component to compensate the fire control solution has been devised and tested against various targets in a range of environments. A photodetector array aligned with the sight's horizontal reticle obtains scene features, which are digitized and processed to separate target from sight motion. Relative motion of the target against the background is briefly monitored to deduce angular crossing rate and a compensating lead angle is introduced into the aim point. Research to gather quantitative data and optimize algorithm performance is described, and some results from field testing are presented.

  5. Automatic Phonetic Transcription for Danish Speech Recognition

    DEFF Research Database (Denmark)

    Kirkedal, Andreas Søeborg

    for English and now extended to cover 50 languages. Due to the nature of open source software, the quality of language support depends greatly on who encoded them. The Danish version was created by a Danish native speaker and contains more than 8,600 spelling-to-phoneme rules and more than 11,000 rules...... for particular words and word classes in addition. In comparison, English has 5,852 spelling-tophoneme rules and 4,133 additional rules and 8,278 rules and 3,829 additional rules. Phonix applies deep morphological analysis as a preprocessing step. Should the analysis fail, several fallback strategies...... to acquire and expensive to create. For languages with productive compounding or agglutinative languages like German and Finnish, respectively, phonetic dictionaries are also hard to maintain. For this reason, automatic phonetic transcription tools have been produced for many languages. The quality...

  6. Automatic Contour Extraction from 2D Image

    Directory of Open Access Journals (Sweden)

    Panagiotis GIOANNIS

    2011-03-01

    Full Text Available Aim: To develop a method for automatic contour extraction from a 2D image. Material and Method: The method is divided in two basic parts where the user initially chooses the starting point and the threshold. Finally the method is applied to computed tomography of bone images. Results: An interesting method is developed which can lead to a successful boundary extraction of 2D images. Specifically data extracted from a computed tomography images can be used for 2D bone reconstruction. Conclusions: We believe that such an algorithm or part of it can be applied on several other applications for shape feature extraction in medical image analysis and generally at computer graphics.

  7. Automatically processing physical data from LHD experiments

    Energy Technology Data Exchange (ETDEWEB)

    Emoto, M., E-mail: emoto.masahiko@nifs.ac.jp; Ida, K.; Suzuki, C.; Yoshida, M.; Akiyama, T.; Nakamura, Y.; Sakamoto, R.; Yokoyama, M.; Yoshinuma, M.

    2014-05-15

    Physical data produced by large helical device (LHD) experiments is supplied by the Kaiseki server, and registers more than 200 types of diagnostic data. Dependencies exist amongst the data; i.e., in many cases, the calculation of one data requires other data. Therefore, to obtain unregistered data, one needs to calculate not only the diagnostic data itself but also the dependent data; however, because the data is registered by different scientists, each scientist must separately calculate and register their respective data. To simplify this complicated procedure, we have developed an automatic calculation system called AutoAna. The calculation programs of AutoAna are distributed on a network, and the number of such programs can be easily increased dynamically. Our system is therefore scalable and ready for substantial increases in the size of the target data.

  8. Automatic detection of secondary creases in fingerprints

    Science.gov (United States)

    Vernon, David

    1993-10-01

    Human fingerprints comprise a series of whorls or ridges. In some special cases, these whorls are broken by so-called secondary creases--collinear breaks across a sequence of adjacent ridges. It is a working hypothesis that the presence of these secondary creases form a physical marker for certain human disorders. A technique to automatically detect such creases in fingerprints is described. This technique utilizes a combination of spatial filtering and region growing to identify the morphology of the locally fragmented fingerprint image. Regions are then thinned to form a skeletal model of the ridge structure. Creases are characterized by collinear terminations on ridges and are isolated by analyzing the Hough transform space derived from the ridge end points. Empirical results using both synthetic and real data are presented and discussed.

  9. The RNA world, automatic sequences and oncogenetics

    International Nuclear Information System (INIS)

    Tahir Shah, K.

    1993-04-01

    We construct a model of the RNA world in terms of naturally evolving nucleotide sequences assuming only Crick-Watson base pairing and self-cleaving/splicing capability. These sequences have the following properties. 1) They are recognizable by an automation (or automata). That is, to each k-sequence, there exist a k-automation which accepts, recognizes or generates the k-sequence. These are known as automatic sequences. Fibonacci and Morse-Thue sequences are the most natural outcome of pre-biotic chemical conditions. 2) Infinite (resp. large) sequences are self-similar (resp. nearly self-similar) under certain rewrite rules and consequently give rise to fractal (resp.fractal-like) structures. Computationally, such sequences can also be generated by their corresponding deterministic parallel re-write system, known as a DOL system. The self-similar sequences are fixed points of their respective rewrite rules. Some of these automatic sequences have the capability that they can read or 'accept' other sequences while others can detect errors and trigger error-correcting mechanisms. They can be enlarged and have block and/or palindrome structure. Linear recurring sequences such as Fibonacci sequence are simply Feed-back Shift Registers, a well know model of information processing machines. We show that a mutation of any rewrite rule can cause a combinatorial explosion of error and relates this to oncogenetical behavior. On the other hand, a mutation of sequences that are not rewrite rules, leads to normal evolutionary change. Known experimental results support our hypothesis. (author). Refs

  10. Automatic Mode Transition Enabled Robust Triboelectric Nanogenerators.

    Science.gov (United States)

    Chen, Jun; Yang, Jin; Guo, Hengyu; Li, Zhaoling; Zheng, Li; Su, Yuanjie; Wen, Zhen; Fan, Xing; Wang, Zhong Lin

    2015-12-22

    Although the triboelectric nanogenerator (TENG) has been proven to be a renewable and effective route for ambient energy harvesting, its robustness remains a great challenge due to the requirement of surface friction for a decent output, especially for the in-plane sliding mode TENG. Here, we present a rationally designed TENG for achieving a high output performance without compromising the device robustness by, first, converting the in-plane sliding electrification into a contact separation working mode and, second, creating an automatic transition between a contact working state and a noncontact working state. The magnet-assisted automatic transition triboelectric nanogenerator (AT-TENG) was demonstrated to effectively harness various ambient rotational motions to generate electricity with greatly improved device robustness. At a wind speed of 6.5 m/s or a water flow rate of 5.5 L/min, the harvested energy was capable of lighting up 24 spot lights (0.6 W each) simultaneously and charging a capacitor to greater than 120 V in 60 s. Furthermore, due to the rational structural design and unique output characteristics, the AT-TENG was not only capable of harvesting energy from natural bicycling and car motion but also acting as a self-powered speedometer with ultrahigh accuracy. Given such features as structural simplicity, easy fabrication, low cost, wide applicability even in a harsh environment, and high output performance with superior device robustness, the AT-TENG renders an effective and practical approach for ambient mechanical energy harvesting as well as self-powered active sensing.

  11. Automatic Recognition of Object Names in Literature

    Science.gov (United States)

    Bonnin, C.; Lesteven, S.; Derriere, S.; Oberto, A.

    2008-08-01

    SIMBAD is a database of astronomical objects that provides (among other things) their bibliographic references in a large number of journals. Currently, these references have to be entered manually by librarians who read each paper. To cope with the increasing number of papers, CDS develops a tool to assist the librarians in their work, taking advantage of the Dictionary of Nomenclature of Celestial Objects, which keeps track of object acronyms and of their origin. The program searches for object names directly in PDF documents by comparing the words with all the formats stored in the Dictionary of Nomenclature. It also searches for variable star names based on constellation names and for a large list of usual names such as Aldebaran or the Crab. Object names found in the documents often correspond to several astronomical objects. The system retrieves all possible matches, displays them with their object type given by SIMBAD, and lets the librarian make the final choice. The bibliographic reference can then be automatically added to the object identifiers in the database. Besides, the systematic usage of the Dictionary of Nomenclature, which is updated manually, permitted to automatically check it and to detect errors and inconsistencies. Last but not least, the program collects some additional information such as the position of the object names in the document (in the title, subtitle, abstract, table, figure caption...) and their number of occurrences. In the future, this will permit to calculate the 'weight' of an object in a reference and to provide SIMBAD users with an important new information, which will help them to find the most relevant papers in the object reference list.

  12. A computer algorithm for automatic beam steering

    International Nuclear Information System (INIS)

    Drennan, E.

    1992-06-01

    Beam steering is done by modifying the current in a trim or bending magnet. If the current change is the right amount the beam can be made to bend in such a manner that it will hit a swic or BPM downstream from the magnet at a predetermined set point. Although both bending magnets and trim magnets can be used to modify beam angle, beam steering is usually done with trim magnets. This is so because, during beam steering the beam angle is usually modified only by a small amount which can be easily achieved with a trim magnet. Thus in this note, all steering magnets will be assumed to be trim magnets. There are two ways of monitoring beam position. One way is done using a BPM and the other is done using a swic. For simplicity, beam position monitoring in this paper will be referred to being done with a swic. Beam steering can be done manually by changing the current through a trim magnet and monitoring the position of the beam downstream from the magnet with a swic. Alternatively the beam can be positioned automatically using a computer which periodically updates the current through a specific number of trim magnets. The purpose of this note is to describe the steps involved in coming up with such a computer program. There are two main aspects to automatic beam steering. First a relationship between the beam position and the bending magnet is needed. Secondly a beamline setup of swics and trim magnets has to be chosen that will position the beam according to the desired specifications. A simple example will be looked at that will show that once a mathematical relationship between the needed change of the beam position on a swic and the change in trim currents is established, a computer could be programmed to calculate and update the trim currents

  13. An automatically tuning intrusion detection system.

    Science.gov (United States)

    Yu, Zhenwei; Tsai, Jeffrey J P; Weigert, Thomas

    2007-04-01

    An intrusion detection system (IDS) is a security layer used to detect ongoing intrusive activities in information systems. Traditionally, intrusion detection relies on extensive knowledge of security experts, in particular, on their familiarity with the computer system to be protected. To reduce this dependence, various data-mining and machine learning techniques have been deployed for intrusion detection. An IDS is usually working in a dynamically changing environment, which forces continuous tuning of the intrusion detection model, in order to maintain sufficient performance. The manual tuning process required by current systems depends on the system operators in working out the tuning solution and in integrating it into the detection model. In this paper, an automatically tuning IDS (ATIDS) is presented. The proposed system will automatically tune the detection model on-the-fly according to the feedback provided by the system operator when false predictions are encountered. The system is evaluated using the KDDCup'99 intrusion detection dataset. Experimental results show that the system achieves up to 35% improvement in terms of misclassification cost when compared with a system lacking the tuning feature. If only 10% false predictions are used to tune the model, the system still achieves about 30% improvement. Moreover, when tuning is not delayed too long, the system can achieve about 20% improvement, with only 1.3% of the false predictions used to tune the model. The results of the experiments show that a practical system can be built based on ATIDS: system operators can focus on verification of predictions with low confidence, as only those predictions determined to be false will be used to tune the detection model.

  14. Automatic registration of serial mammary gland sections

    Energy Technology Data Exchange (ETDEWEB)

    Arganda-Carreras, Ignacio; Fernandez-Gonzalez, Rodrigo; Ortiz-de-Solorzano, Carlos

    2004-04-13

    We present two new methods for automatic registration of microscope images of consecutive tissue sections. They represent two possibilities for the first step in the 3-D reconstruction of histological structures from serially sectioned tissue blocks. The goal is to accurately align the sections in order to place every relevant shape contained in each image in front of its corresponding shape in the following section before detecting the structures of interest and rendering them in 3D. This is accomplished by finding the best rigid body transformation (translation and rotation) of the image being registered by maximizing a matching function based on the image content correlation. The first method makes use of the entire image information, whereas the second one uses only the information located at specific sites, as determined by the segmentation of the most relevant tissue structures. To reduce computing time, we use a multiresolution pyramidal approach that reaches the best registration transformation in increasing resolution steps. In each step, a subsampled version of the images is used. Both methods rely on a binary image which is a thresholded version of the Sobel gradients of the image (first method) or a set of boundaries manually or automatically obtained that define important histological structures of the sections. Then distance-transform of the binary image is computed. A proximity function is then calculated between the distance image of the image being registered and that of the reference image. The transformation providing a maximum of the proximity function is then used as the starting point of the following step. This is iterated until the registration error lies below a minimum value.

  15. Transplacental transmission of Human Papillomavirus

    Directory of Open Access Journals (Sweden)

    Serafini Eduardo P

    2008-09-01

    Full Text Available Abstract This paper aimed at studying the transplacental transmission of HPV and looking at the epidemiological factors involved in maternal viral infection. The following sampling methods were used: (1 in the pregnant woman, (a genital; (b peripheral blood; (2 in the newborn, (a oral cavity, axillary and inguinal regions; (b nasopharyngeal aspirate, and (c cord blood; (3 in the placenta. The HPV DNA was identified using two methods: multiplex PCR of human β-globin and of HPV using the PGMY09 and PGMY11 primers; and nested-PCR, which combines degenerated primers of the E6/E7 regions of the HPV virus, that allowed the identification of genotypes 6/11, 16, 18, 31, 33, 42, 52 and 58. Transplacental transmission was considered when type-specific HPV concordance was found between the mother, the placenta and the newborn or the mother and cord blood. The study included 49 HPV DNA-positive pregnant women at delivery. Twelve placentas (24.5%, n = 12/49 had a positive result for HPV DNA. Eleven newborn were HPV DNA positive in samples from the nasopharyngeal or buccal and body or cord blood. In 5 cases (10.2%, n = 5/49 there was HPV type-specific agreement between genital/placenta/newborn samples. In one case (2%, n = 1/49 there was type specific HPV concordance between genital/cord blood and also suggested transplacental transmission. A positive and significant correlation was observed between transplacental transmission of HPV infection and the maternal variables of immunodepression history (HIV, p = 0.011. In conclusion the study suggests placental infection in 23.3% of the cases studied and transplacental transmission in 12.2%. It is suggested that in future HPV DNA be researched in the normal endometrium of women of reproductive age. The possible consequence of fetal exposure to HPV should be observed.

  16. 30 CFR 77.410 - Mobile equipment; automatic warning devices.

    Science.gov (United States)

    2010-07-01

    ... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Mobile equipment; automatic warning devices. 77... UNDERGROUND COAL MINES Safeguards for Mechanical Equipment § 77.410 Mobile equipment; automatic warning devices. (a) Mobile equipment such as front-end loaders, forklifts, tractors, graders, and trucks, except...

  17. Statistical pattern recognition for automatic writer identification and verification

    NARCIS (Netherlands)

    Bulacu, Marius Lucian

    2007-01-01

    The thesis addresses the problem of automatic person identification using scanned images of handwriting.Identifying the author of a handwritten sample using automatic image-based methods is an interesting pattern recognition problem with direct applicability in the forensic and historic document

  18. 24 CFR 982.455 - Automatic termination of HAP contract.

    Science.gov (United States)

    2010-04-01

    ... URBAN DEVELOPMENT SECTION 8 TENANT BASED ASSISTANCE: HOUSING CHOICE VOUCHER PROGRAM Housing Assistance Payments Contract and Owner Responsibility § 982.455 Automatic termination of HAP contract. The HAP contract terminates automatically 180 calendar days after the last housing assistance payment to the owner...

  19. 21 CFR 892.1900 - Automatic radiographic film processor.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Automatic radiographic film processor. 892.1900 Section 892.1900 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... processor. (a) Identification. An automatic radiographic film processor is a device intended to be used to...

  20. Automatic transcription of continuous speech into syllable-like units ...

    Indian Academy of Sciences (India)

    Abstract. The focus of this paper is to automatically segment and label continu- ous speech signal into syllable-like units for Indian languages. In this approach, the continuous speech signal is first automatically segmented into syllable-like units using group delay based algorithm. Similar syllable segments are then grouped.

  1. A Machine Vision System for Automatically Grading Hardwood Lumber - (Proceedings)

    Science.gov (United States)

    Richard W. Conners; Tai-Hoon Cho; Chong T. Ng; Thomas H. Drayer; Joe G. Tront; Philip A. Araman; Robert L. Brisbon

    1990-01-01

    Any automatic system for grading hardwood lumber can conceptually be divided into two components. One of these is a machine vision system for locating and identifying grading defects. The other is an automatic grading program that accepts as input the output of the machine vision system and, based on these data, determines the grade of a board. The progress that has...

  2. Automatic reel controls filler wire in welding machines

    Science.gov (United States)

    Millett, A. V.

    1966-01-01

    Automatic reel on automatic welding equipment takes up slack in the reel-fed filler wire when welding operation is terminated. The reel maintains constant, adjustable tension on the wire during the welding operation and rewinds the wire from the wire feed unit when the welding is completed.

  3. The profitability of automatic milking on Dutch dariy farms

    NARCIS (Netherlands)

    Bijl, R.; Kooistra, S.R.; Hogeveen, H.

    2007-01-01

    Several studies have reported on the profitability of automatic milking based on different simulation models, but a data-based study using actual farm data has been lacking. The objective of this study was to analyze the profitability of dairy farms having an automatic milking system (AMS) compared

  4. Automatic age and gaze estimation under uncontrolled conditions

    NARCIS (Netherlands)

    Alnajar, F.

    2016-01-01

    Can the computer learn a person’s age just from analyzing facial images obtained by a simple webcam? If so, you can automatically determine if a person has the right age to buy beer (shops), to use a credit card (retail), and can enter bars (entertainment). Can the computer automatically recognize

  5. 2013 International Conference on Mechatronics and Automatic Control Systems

    CERN Document Server

    2014-01-01

    This book examines mechatronics and automatic control systems. The book covers important emerging topics in signal processing, control theory, sensors, mechanic manufacturing systems and automation. The book presents papers from the 2013 International Conference on Mechatronics and Automatic Control Systems held in Hangzhou, China on August 10-11, 2013. .

  6. Automatic sign language recognition inspired by human sign perception

    NARCIS (Netherlands)

    Ten Holt, G.A.

    2010-01-01

    Automatic sign language recognition is a relatively new field of research (since ca. 1990). Its objectives are to automatically analyze sign language utterances. There are several issues within the research area that merit investigation: how to capture the utterances (cameras, magnetic sensors,

  7. Enhancing Automaticity through Task-Based Language Learning

    Science.gov (United States)

    De Ridder, Isabelle; Vangehuchten, Lieve; Gomez, Marta Sesena

    2007-01-01

    In general terms automaticity could be defined as the subconscious condition wherein "we perform a complex series of tasks very quickly and efficiently, without having to think about the various components and subcomponents of action involved" (DeKeyser 2001: 125). For language learning, Segalowitz (2003) characterised automaticity as a…

  8. Reliability and effectiveness of clickthrough data for automatic image annotation

    NARCIS (Netherlands)

    Tsikrika, T.; Diou, C.; De Vries, A.P.; Delopoulos, A.

    2010-01-01

    Automatic image annotation using supervised learning is performed by concept classifiers trained on labelled example images. This work proposes the use of clickthrough data collected from search logs as a source for the automatic generation of concept training data, thus avoiding the expensive

  9. Reliability and effectiveness of clickthrough data for automatic image annotation

    NARCIS (Netherlands)

    T. Tsikrika (Theodora); C. Diou; A.P. de Vries (Arjen); A. Delopoulos

    2010-01-01

    htmlabstractAutomatic image annotation using supervised learning is performed by concept classifiers trained on labelled example images. This work proposes the use of clickthrough data collected from search logs as a source for the automatic generation of concept training data, thus avoiding the

  10. Apparatus for the automatic determination of oxygen consumption in ...

    African Journals Online (AJOL)

    APPARATUS FOR THE AUTOMATIC DETERMINATION OF OXYGEN. CONSUMPTION IN FISH l. F. !C. MARAIS, A. F. A. AlCBRS and P. VAN DEI. RYST. Department o/Zoology, U"iversity 0/ Port Elizabeth. ABSTRACT. An apparatus is described which permits the automatic determination of the oxygen consumption of three ...

  11. Automatic Video-based Analysis of Human Motion

    DEFF Research Database (Denmark)

    Fihl, Preben

    The human motion contains valuable information in many situations and people frequently perform an unconscious analysis of the motion of other people to understand their actions, intentions, and state of mind. An automatic analysis of human motion will facilitate many applications and thus has...... bring the solution of fully automatic analysis and understanding of human motion closer....

  12. microcontroller based automatic control for water pumping machine

    African Journals Online (AJOL)

    user

    In this paper a Microcontroller Based Automatic Control for Water Pumping. Machine and Level Indicator (MBACWPMLI) has been designed, constructed and tested. The MBACWPML I uses the reflection of sound (echo) to give the indication of water level in a storage tank and also the automatic control of the water pumping ...

  13. The research and development of the automatic solar power tracker

    OpenAIRE

    Li Yan Ping; Yuan Zhong Ying

    2016-01-01

    The article describes a kind of automatic tracker using solar power. It depends on two important parts which are servo system and adjusting mechanism system to keep the tracker operating normally. The article focuses on describing the characteristics and functions of two systems and the operating details of the automatic solar power tracker.

  14. Automatic Detection of Inactive Solar Cell Cracks in Electroluminescence Images

    DEFF Research Database (Denmark)

    Spataru, Sergiu; Hacke, Peter; Sera, Dezso

    2017-01-01

    We propose an algorithm for automatic determination of the electroluminescence (EL) signal threshold level corresponding to inactive solar cell cracks, resulting from their disconnection from the electrical circuit of the cell. The method enables automatic quantification of the cell crack size an...

  15. The research and development of the automatic solar power tracker

    Directory of Open Access Journals (Sweden)

    Li Yan Ping

    2016-01-01

    Full Text Available The article describes a kind of automatic tracker using solar power. It depends on two important parts which are servo system and adjusting mechanism system to keep the tracker operating normally. The article focuses on describing the characteristics and functions of two systems and the operating details of the automatic solar power tracker.

  16. System for Automatic Generation of Examination Papers in Discrete Mathematics

    Science.gov (United States)

    Fridenfalk, Mikael

    2013-01-01

    A system was developed for automatic generation of problems and solutions for examinations in a university distance course in discrete mathematics and tested in a pilot experiment involving 200 students. Considering the success of such systems in the past, particularly including automatic assessment, it should not take long before such systems are…

  17. Working Memory Load and Automaticity in Relation to Mental Multiplication

    Science.gov (United States)

    Ding, Yi; Liu, Ru-De; Xu, Le; Wang, Jia; Zhang, Dake

    2017-01-01

    The authors' aim was to examine the relations among mental multiplication, working memory load (WML), and automaticity by alternating the difficulty level of task characteristics. In Experiment 1, involving 30 fifth-grade students with mixed abilities, a 2 (WML) × 2 (automaticity) design was utilized. In Experiment 2, involving 21 high-achieving…

  18. A model based method for automatic facial expression recognition

    NARCIS (Netherlands)

    Kuilenburg, H. van; Wiering, M.A.; Uyl, M. den

    2006-01-01

    Automatic facial expression recognition is a research topic with interesting applications in the field of human-computer interaction, psychology and product marketing. The classification accuracy for an automatic system which uses static images as input is however largely limited by the image

  19. Distributed automatic control of technological processes in conditions of weightlessness

    Science.gov (United States)

    Kukhtenko, A. I.; Merkulov, V. I.; Samoylenko, Y. I.; Ladikov-Royev, Y. P.

    1986-01-01

    Some problems associated with the automatic control of liquid metal and plasma systems under conditions of weightlessness are examined, with particular reference to the problem of stability of liquid equilibrium configurations. The theoretical fundamentals of automatic control of processes in electrically conducting continuous media are outlined, and means of using electromagnetic fields for simulating technological processes in a space environment are discussed.

  20. Automatic Derivation of Name Access Points in Cataloging.

    Science.gov (United States)

    Svenonius, Elaine; Molto, Mavis

    1990-01-01

    Describes research that examined the feasibility of automatically deriving name access points from machine readable title pages of English language monographs. An algorithm for automatic derivation is presented and results using the algorithm are compared to traditionally cataloged name access points. The implications for bibliographic standards…