The FRJ-1 (MERLIN) research reactor: its main activity inventory has been removed by successful demolition of the reactor block

International Nuclear Information System (INIS)

Stahn, B.; Printz, R.; Matela, K.; Zehbe, C.; Poeppinghaus, J.; Cremer, J.

2004-01-01

The FRJ-1 (MERLIN) research reactor was decommissioned in 1985 after twenty-three years of operation. Demolition of the plant was begun in 1996. The article contains a survey of the demolition steps carried out so far within the framework of three partial permits. The main activity is the demolition of the reactor core structures as a precondition for subsequent measures to ensure clearance measurements of the building. The core structures are demolished which were exposed to high neutron fluxes during reactor operation and now show the highest activity and dose rate levels, except for the core internals. For demolition and disassembly of the metal structures in this part of the plant, the tools specially designed and made include a remotely operated sawing system and a pipe cutting system for internal segmentation of the beam lines. The universal demolition tool for use also above and beyond the concrete structures has been found to be a remotely controlled electrohydraulic demolition shovel. Spreading contamination in the course of the demolition work was avoided. One major reason for this success was the fact that no major airborne contamination existed at any time as a consequence of the quality of the material demolished and also of the consistent use of technical tools. While the reactor block was being demolished, an application for clearance measurement of the reactor hall and subsequent release from the scope of the Atomic Energy Act was filed as early as in mid-2003. The fourth partial permit covering these activities is expected to be issued in the spring of 2004. (orig.)

26 CFR 1.280B-1 - Demolition of structures.

Science.gov (United States)

2010-04-01

... 26 Internal Revenue 3 2010-04-01 2010-04-01 false Demolition of structures. 1.280B-1 Section 1... (CONTINUED) INCOME TAXES Items Not Deductible § 1.280B-1 Demolition of structures. (a) In general. Section 280B provides that, in the case of the demolition of any structure, no deduction otherwise allowable...

A Sandia National Laboratories decontamination and demolition success story

International Nuclear Information System (INIS)

Miller, D.R.; Barber, D.S.; Lipka, G.

1994-01-01

Sandia National Laboratories/New Mexico (SNL/NM) has established a formal facility assessment, decontamination and demolition oversight process with the goal of ensuring that excess or contaminated facilities are managed in a cost-effective manner that is protective of human health and the environment. The decontamination and demolition process is designed so that all disciplines are consulted and have input from the initiation of a project. The committee consists of all essential Environmental, Safety and Health (ES and H) and Facilities disciplines. The interdisciplinary-team approach has provided a mechanism that verifies adequate building and site assessment activities are conducted. This approach ensures that wastes generated during decontamination and demolition activities are handled and disposed according to Department of Energy (DOE), Federal, state, and local requirements. Because of the comprehensive nature of the SNL decontamination and demolition process, the strategy can be followed for demolition, renovation and new construction projects, regardless of funding source. An overview of the SNL/NM decontamination and demolition process is presented through a case study which demonstrates the practical importance of the formal process

K-25 Structural Separation and Demolition

International Nuclear Information System (INIS)

Cater, Frank

2008-01-01

The K-25 building is a former gaseous diffusion plant, built in 1944-1945 as part of the United States Manhattan Project. The structure was the largest structure under one roof, surpassed only by the Pentagon. Together the three wings represent about 17.8 hectare (44 acres) under roof and are generally about 18.3 meters (60 ft.) high on the outside face and approximately 12.2 meters (40 ft.) high on the inside face. The entire structure was built in the shape of a 'U', with a lateral distance of approximately one mile. It was constructed in individual building units with each unit connected using expansion joint-type connection. A single unit is approximately 24.4 meters (80 ft.) across and 122 meters (400 ft.) deep. The northern structure is connected to the eastern and western structures at the upper level floors. The four-level, U-shaped building is a steel-frame structure with corrugated cement-asbestos siding. The cell level is an elevated concrete structure supported by reinforced concrete columns located in the basement, or vault area. The vault area can be accessed at grade level from the outside perimeter. Inside the courtyard, the grade level has been raised to provide entry to the second or cell floor level. An engineering evaluation of the structure was performed to determine the condition of the structure and possibility of unplanned collapse of any portion of the structure. The evaluation included physical inspections, calculations for wind, pre-demolition loads, and evaluation of failure modes. The results of the evaluation have provided guidance for the demolition plan and the development of criteria for protection of personnel performing pre-demolition activities. Challenges include degradation of the structure that necessitated repair, dealing with changes in the code revisions from both the American Concrete Institute (ACI) and the American Institute of Steel Construction (AISC), access to areas of the structure that were not necessarily designed

Sea-dumped CW munitions - the European component

International Nuclear Information System (INIS)

Hart, J.; Stock, T.

2009-01-01

The purpose of this contribution is to outline the European magnitude of sea-dumped CW munitions. Hereby the paper attempts to provide an overview on historical dumping activities, both for conventional and chemical munitions. The potential dangers which might result from these dumping activities are discussed in brief. Among others the differences in deep sea dumping and dumping in shallow waters are evaluated. Further, the presentation will outline and discuss the different technology steps: (a) identification, (b) recovery, (c) transportation and (d) destruction (on- or off-shore), necessary for possible cleaning of dumping sites. Thereafter an evaluation of the different technologies available/applied is performed, in particular on the destruction part. Hereby the already practised experience is displayed. Based upon existing treaty regimes an actual judgment of possible application of treaty provisions for demanding cleaning up operations is discussed. The question if treaty obligations can be used to force cleaning operations is debated. A possible match of the technology package available with the scope/magnitude of the munitions dumping problem is discussed. Hereby the gaps between the size of the problem and the most suitable technologies for recovery and destruction are illustrated. The resulting answers should be regarded as possible technical guidelines for future development activities as well existing limitations to solve the problems. The papers will result in some general guidelines for future prospect on the issues of dumped munitions, in particular chemical munitions under the European context.(author)

Missile/Munition Integration Facility

Data.gov (United States)

Federal Laboratory Consortium — A large complex contained within approximately 600 acres with security fencing, controlled access gates, and a munitions convoy access road. The complex is capable...

Large-Scale Residential Demolition

Science.gov (United States)

The EPA provides resources for handling residential demolitions or renovations. This includes planning, handling harmful materials, recycling, funding, compliance assistance, good practices and regulations.

The Environmental Challenge of Military Munitions and Federal Facilities

Science.gov (United States)

EPA and the Department of Defense (DoD) must address the contamination legacy left by military munitions and explosives of concern (MEC) and other hazardous munitions materials from military live-fire training or testing.

THE EFFECT OF VESSEL SUPPLY ON SHIP-DEMOLITION PRICES

Directory of Open Access Journals (Sweden)

Nikos Kagkarakis

2017-02-01

Full Text Available The ship-demolition is one of the four main markets that form the shipping industry and plays an important role on the seaborne trade, as it mitigates imbalances between supply and demand for transportation services by adjusting the merchant fleet supply. The aim of this study is to examine whether the factors that determine the supply of vessels for demolition are capable of affecting materially the ship-demolition price formation. The availability of ships for demolition is primarily a function of the fleet’s age and the conditions on the freight and secondhand markets. The analysis is conducted on the crude tanker and the bulk carrier segments and the vector autoregressive model methodology is employed, whereby the effect of both the supply and the demand factors on the ship-demolition prices is examined. The results indicate that the supply side has limited effect on the price formation in the industry, which is driven by the demand for the steel-scrap commodity.

Hawaii Munitions Monitoring Station and Natural Laboratory

Science.gov (United States)

Edwards, M.; Trimble, A. Z.; Rognstad, M. R.

2017-12-01

Hundreds of thousands of tons of conventional munitions were fired into the ocean at military ranges or deliberately disposed at sea during the twentieth century. Potential contaminants from munitions and explosives of concern (MEC) affect virtually every coast in the United States, including Alaska, the Hawaiian Islands, Guam, American Samoa and other U.S. territories as well as inland waterways. It is necessary to develop methods to assess the concentrations of munitions constituents present at a site to address concerns about the presence of environmentally relevant concentrations and their potential impacts. Having a well-characterized site to test instruments and methods is important for continued development and refinement of technology. Most sites are too big to characterize comprehensively in three dimensions over time periods lasting days or longer. We are working to develop a monitoring station and natural laboratory near Oahu, Hawaii to create a cost-effective demonstration and validation natural laboratory where emerging technologies can be evaluated and compared. Ordnance Reef (OR) is an ideal location to establish a munitions monitoring station for historical, logistical and environmental reasons. OR is an area of shallow fringing reef measuring approximately 4.2 km by 2.2 km along the Waianae coast of Oahu that was used as a disposal area for military munitions following World War II. OR has been the subject of multiple investigations including an inventory of munitions conducted by the U.S. Army Corps of Engineers in 2002 and a screening-level risk investigation conducted by the National Oceanic and Atmospheric Administration and the University of Hawaii in 2006. As a result, there are multiple datasets collected over the past fifteen years that can be leveraged to serve as a baseline for the natural laboratory. These extant datasets are being supplemented with data from integrated unmanned systems deployed at OR to characterize and visualize the

200 West Area Ash Pit Demolition Site closure plan. Revision 1

International Nuclear Information System (INIS)

Ruck, F.R.

1994-01-01

The Ash Pit Demolition Site had two known demolition events, the first occurred in November of 1984, and the second occurred in June of 1986. These demolition events were a form of thermal treatment for discarded explosive chemical products. Because the Ash Pit Demolition Site will no longer be used for this thermal activity, the site will be closed. Closure will be conducted pursuant to the requirements of the Washington State Department of Ecology (Ecology) ''Dangerous Waste Regulations'', Washington Administrative Code (WAC) 173-303-610 and 40 Code of Federal Regulations (CFR) 270.1. The 200 West Area Ash Pit Demolition Site Closure Plan consists of a Part A, Form 3, Dangerous Waste Permit Application (Revision 4) and a closure plan. An explanation of the Part A, Form 3, submitted with this closure plan is provided at the beginning of the Part A Section. The closure plan consists of nine chapters and five appendices. This closure plan presents a description of the Ash,Pit Demolition Site, the history of the waste treated, and the approach that will be followed to close the Ash Pit Demolition Site. Because there were no radioactively contaminated chemicals involved in the demolitions, the information on radionuclides is provided for ''information only''. Remediation of any radioactive contamination is not within the scope of this closure plan. Only dangerous constituents derived from Ash Pit Demolition Site operations will be addressed in this closure plan in accordance with WAC 173-303-610(2)(b)(i)

Munitions Classification Library

Science.gov (United States)

2016-04-04

members of the community to make their own additions to any, or all, of the classification libraries . The next phase entailed data collection over less......Include area code) 04/04/2016 Final Report August 2014 - August 2015 MUNITIONS CLASSIFICATION LIBRARY Mr. Craig Murray, Parsons Dr. Thomas H. Bell, Leidos

218-E-8 Borrow Pit Demolition Site closure plan. Revision 1

International Nuclear Information System (INIS)

Ruck, F.R.

1994-01-01

The 218-E-8 Demolition Site was the site of a single demolition event in November of 1984. This demolition event was a form of thermal treatment for discarded explosive chemical products. Because the 218-E-8 Demolition Site will no longer be used for this thermal activity, the site will be closed. Closure will be conducted pursuant to the requirements of the Washington State Department of Ecology (Ecology) ''Dangerous Waste Regulations,'' Washington Administrative Code (WAC) 173-303-610 and 40 Code of Federal Regulations (CFR) 270.1. The 218-E-8 Borrow Pit Demolition Site Closure Plan consists of a Hanford Facility Dangerous Waste Part A Permit Application, Form 3, Revision 4, and a closure plan. An explanation of the Part A Form 3, submitted with this closure plan is provided at the beginning of the Part A Section. The closure plan consists of nine chapters and five appendices. This closure plan presents a description of the 218-E-8 Demolition Site, the history of the waste treated, and the approach that will be followed to close the 218-E-8 Demolition Site. Because there were no radioactively contaminated chemicals involved in t he demolitions at the 218-E-8 Borrow Pit site, the information on radionuclides is provided for ''information only.'' Remediation of any radioactive contamination is not within the scope of this closure plan. Only dangerous constituents derived from 218-E-8 Demolition Site operations will be addressed in this closure plan in accordance with WAC 173-303-610(2)(b)(i)

Management of construction and demolition wastes as secondary building resources

Science.gov (United States)

Manukhina, Lyubov; Ivanova, Irina

2017-10-01

The article analyzes the methods of management of construction and demolition wastes. The authors developed suggestions for improving the management system of the turnover of construction and demolition wastes. Today the issue of improving the management of construction and demolition wastes is of the same importance as problems of protecting the life-support field from pollution and of preserving biological and land resources. The authors educed the prospective directions and methods for improving the management of the turnover processes for construction and demolition wastes, including the evaluation of potential of wastes as secondary raw materials and the formation of a centralized waste management system.

Construction and demolition waste indicators.

Science.gov (United States)

Mália, Miguel; de Brito, Jorge; Pinheiro, Manuel Duarte; Bravo, Miguel

2013-03-01

The construction industry is one of the biggest and most active sectors of the European Union (EU), consuming more raw materials and energy than any other economic activity. Furthermore, construction waste is the commonest waste produced in the EU. Current EU legislation sets out to implement construction and demolition waste (CDW) prevention and recycling measures. However it lacks tools to accelerate the development of a sector as bound by tradition as the building industry. The main objective of the present study was to determine indicators to estimate the amount of CDW generated on site both globally and by waste stream. CDW generation was estimated for six specific sectors: new residential construction, new non-residential construction, residential demolition, non-residential demolition, residential refurbishment, and non-residential refurbishment. The data needed to develop the indicators was collected through an exhaustive survey of previous international studies. The indicators determined suggest that the average composition of waste generated on site is mostly concrete and ceramic materials. Specifically for new residential and new non-residential construction the production of concrete waste in buildings with a reinforced concrete structure lies between 17.8 and 32.9 kg m(-2) and between 18.3 and 40.1 kg m(-2), respectively. For the residential and non-residential demolition sectors the production of this waste stream in buildings with a reinforced concrete structure varies from 492 to 840 kg m(-2) and from 401 to 768 kg/m(-2), respectively. For the residential and non-residential refurbishment sectors the production of concrete waste in buildings lies between 18.9 and 45.9 kg/m(-2) and between 18.9 and 191.2 kg/m(-2), respectively.

Estimation of construction and demolition waste using waste generation rates in Chennai, India.

Science.gov (United States)

Ram, V G; Kalidindi, Satyanarayana N

2017-06-01

A large amount of construction and demolition waste is being generated owing to rapid urbanisation in Indian cities. A reliable estimate of construction and demolition waste generation is essential to create awareness about this stream of solid waste among the government bodies in India. However, the required data to estimate construction and demolition waste generation in India are unavailable or not explicitly documented. This study proposed an approach to estimate construction and demolition waste generation using waste generation rates and demonstrated it by estimating construction and demolition waste generation in Chennai city. The demolition waste generation rates of primary materials were determined through regression analysis using waste generation data from 45 case studies. Materials, such as wood, electrical wires, doors, windows and reinforcement steel, were found to be salvaged and sold on the secondary market. Concrete and masonry debris were dumped in either landfills or unauthorised places. The total quantity of construction and demolition debris generated in Chennai city in 2013 was estimated to be 1.14 million tonnes. The proportion of masonry debris was found to be 76% of the total quantity of demolition debris. Construction and demolition debris forms about 36% of the total solid waste generated in Chennai city. A gross underestimation of construction and demolition waste generation in some earlier studies in India has also been shown. The methodology proposed could be utilised by government bodies, policymakers and researchers to generate reliable estimates of construction and demolition waste in other developing countries facing similar challenges of limited data availability.

Chronic lower respiratory diseases among demolition and cement workers

DEFF Research Database (Denmark)

Mølgaard, Ellen Fischer; Hannerz, Harald; Tüchsen, Finn

2013-01-01

To estimate standardised hospitalisation ratios (SHR) for chronic lower respiratory diseases among demolition and cement workers in Denmark, 1995-2009.......To estimate standardised hospitalisation ratios (SHR) for chronic lower respiratory diseases among demolition and cement workers in Denmark, 1995-2009....

Stripping demolition of concrete by applying electric current through reinforcing bars

International Nuclear Information System (INIS)

Nakagawa, Wahei; Kumegawa, Sadatsune

1995-01-01

The presence of reinforcing bars in reinforced concrete structures is an obstruction hindering the smooth progress of demolition works. The electric heating method is, on the other hand, a demolition technique of unique concept since it adopts the bars to help the demolition of reinforced concrete structures. This technique has the following advantages for demolition: 1) the more densely a structure is reinforced with bars, the greater is the effect of the electric heating, 2) demolition after heating produces little dust, and 3) electric heating of reinforcing bars causes no damage to the portions of concrete not subjected to electric current. The present paper describes the procedures and results of a series of experiments we conducted to verify the efficiency of the electric heating method. In this method, a low-voltage high-current is run through reinforcing bars existing in a concrete structure, inducing intense heat in the bars which in its turn brings about cracks in the surrounding concrete mass, facilitating secondary demolition by hammer picks or other means. The experiments were performed on full-scale biological shield wall mock-ups of a BWR and a small nuclear reactor. The experiments revealed that these excellent features of the electric heating method are worth utilizing in stripping demolition of radioactivated regions of biological shield walls in nuclear power plants. The electric heating method is currently being adopted and shows effective results in partial demolition works in diaphragm wall shafts where starting/arriving holes are to be fixed for shield machines without damaging surrounding portions. (author)

76 FR 35006 - Recovery Policy RP9523.4, Demolition of Private Structures

Science.gov (United States)

2011-06-15

...] Recovery Policy RP9523.4, Demolition of Private Structures AGENCY: Federal Emergency Management Agency, DHS... (FEMA) is accepting comments on Recovery Policy RP9523.4, Demolition of Private Structures. DATES... guidance in determining the eligibility of demolition of private structures under the provisions of the...

Optimal Control of Sensor Threshold for Autonomous Wide Area Search Munitions

National Research Council Canada - National Science Library

Kish, Brian A; Jacques, David R; Pachter, Meir

2005-01-01

The optimal employment of autonomous wide area search munitions is addressed. The scenario considered involves an airborne munition searching a battle space for stationary targets in the presence of false targets...

Spread, Behavior, and Ecosystem Consequences of Conventional Munitions Compounds in Coastal Marine Waters

Directory of Open Access Journals (Sweden)

Aaron J. Beck

2018-04-01

Full Text Available Coastal marine environments are contaminated globally with a vast quantity of unexploded ordnance and munitions from intentional disposal. These munitions contain organic explosive compounds as well as a variety of metals, and represent point sources of chemical pollution to marine waters. Most underwater munitions originate from World Wars at the beginning of the twentieth century, and metal munitions housings have been impacted by extensive corrosion over the course of the following decades. As a result, the risk of munitions-related contaminant release to the water column is increasing. The behavior of munitions compounds is well-characterized in terrestrial systems and groundwater, but is only poorly understood in marine systems. Organic explosive compounds, primarily nitroaromatics and nitramines, can be degraded or transformed by a variety of biotic and abiotic mechanisms. These reaction products exhibit a range in biogeochemical characteristics such as sorption by particles and sediments, and variable environmental behavior as a result. The reaction products often exhibit increased toxicity to biological receptors and geochemical controls like sorption can limit this exposure. Environmental samples typically show low concentrations of munitions compounds in water and sediments (on the order of ng/L and μg/kg, respectively, and ecological risk appears generally low. Nonetheless, recent work demonstrates the possibility of sub-lethal genetic and metabolic effects. This review evaluates the state of knowledge on the occurrence, fate, and effect of munition-related chemical contaminants in the marine environment. There remain a number of knowledge gaps that limit our understanding of munitions-related contaminant spread and effect, and the need for additional work is made all the more urgent by increasing risk of release to the environment.

Computational Modeling of Hydrodynamics and Scour around Underwater Munitions

Science.gov (United States)

Liu, X.; Xu, Y.

2017-12-01

Munitions deposited in water bodies are a big threat to human health, safety, and environment. It is thus imperative to predict the motion and the resting status of the underwater munitions. A multitude of physical processes are involved, which include turbulent flows, sediment transport, granular material mechanics, 6 degree-of-freedom motion of the munition, and potential liquefaction. A clear understanding of this unique physical setting is currently lacking. Consequently, it is extremely hard to make reliable predictions. In this work, we present the computational modeling of two importance processes, i.e., hydrodynamics and scour, around munition objects. Other physical processes are also considered in our comprehensive model. However, they are not shown in this talk. To properly model the dynamics of the deforming bed and the motion of the object, an immersed boundary method is implemented in the open source CFD package OpenFOAM. Fixed bed and scour cases are simulated and compared with laboratory experiments. The future work of this project will implement the coupling between all the physical processes.

Munitions in the Underwater Environment: State of the Science and Knowledge Gaps

Science.gov (United States)

2010-06-01

the Munitions Items Disposition Action System ( MIDAS ). Munitions constituents (MCs) can be identified through the known munitions type. The MIDAS and...physical damage to the casing, adjacent or touching metals, and water or substrate qualities such as temperature, pH, or Redox potential. The...environments, little is known on modeling the fate of MCs in the underwater environment. One of the anticipated problems in predicting the fate and

OPEN AIR DEMOLITION OF FACILITIES HIGHLY CONTAMINATED WITH PLUTONIUM

International Nuclear Information System (INIS)

LLOYD, E.R.

2007-01-01

The demolition of highly contaminated plutonium buildings usually is a long and expensive process that involves decontaminating the building to near free- release standards and then using conventional methods to remove the structure. It doesn't, however, have to be that way. Fluor has torn down buildings highly contaminated with plutonium without excessive decontamination. By removing the select source term and fixing the remaining contamination on the walls, ceilings, floors, and equipment surfaces; open-air demolition is not only feasible, but it can be done cheaper, better (safer), and faster. Open-air demolition techniques were used to demolish two highly contaminated buildings to slab-on-grade. These facilities on the Department of Energy's Hanford Site were located in, or very near, compounds of operating nuclear facilities that housed hundreds of people working on a daily basis. To keep the facilities operating and the personnel safe, the projects had to be creative in demolishing the structures. Several key techniques were used to control contamination and keep it within the confines of the demolition area: spraying fixatives before demolition; applying fixative and misting with a fine spray of water as the buildings were being taken down; and demolishing the buildings in a controlled and methodical manner. In addition, detailed air-dispersion modeling was done to establish necessary building and meteorological conditions and to confirm the adequacy of the proposed methods. Both demolition projects were accomplished without any spread of contamination outside the modest buffer areas established for contamination control. Furthermore, personnel exposure to radiological and physical hazards was significantly reduced by using heavy equipment rather than ''hands on'' techniques

218 E-8 Borrow Pit Demolition Site clean closure soil evaluation report

International Nuclear Information System (INIS)

Korematsu-Olund, D.M.

1995-01-01

This report summarizes the sampling activities undertaken and the analytical results obtained in a soil sampling and analyses study performed for the 218 E-8 Borrow Pit Demolition Site (218 E-8 Demolition Site). The 218 E-8 Demolition Site is identified as a Resource Conservation and Recovery Act (RCRA) treatment unit that will be closed in accordance with the applicable laws and regulations. The site was used for the thermal treatment of discarded explosive chemical products. No constituents of concern were found in concentrations indicating contamination of the soil by 218 E-8 Demolition Site activities

Mercury-Containing Devices and Demolition

Science.gov (United States)

Some items inside residential buildings contain mercury, which poses a persistent and toxic human health and environmental threat. These materials should be carefully salvaged for proper recycling to prevent mercury contamination prior to demolition.

Validation of Passive Sampling Devices for Monitoring of Munitions Constituents in Underwater Environments

Science.gov (United States)

2017-09-01

TNT TOC TSS Low Order Detonation Munitions constituents Munitions Debris Method Detection Limit Munitions and explosives of concern Mean low...Total organic carbon ( TOC ) and grain size distribution from stations A1, T10, T11, and T12 at BSS...16 syringes/stn) TNT, ADNTs, DNTs, RDX 4 locations in BSS based on positive POCIS results Sediment 5 TOC , grain size 4, co-located with sediment

200 West Ash Pit Demolition Site closure plan

International Nuclear Information System (INIS)

1992-11-01

The Hanford Facility is owned by the US Government and operated by the US Department of Energy, Richland Field Office. Dangerous waste and mixed waste (containing both radioactive and dangerous components) are managed and produced on the Hanford Facility. Westinghouse Hanford Company is a major contractor to the US Department of Energy, Richland Field Office and serves as cooperator of the 200 West Ash Pit Demolition Site, the unit addressed in this closure plan. The 200 West Ash Pit Demolition Site Closure Plan consists of a Part A Permit Application (Revision 3) and a closure plan. An explanation of the Part A Permit Application revision is provided at the beginning of the Part A section. The closure plan consists of nine chapters and three appendices. This 200 West Ash Pit Demolition Site Closure Plan submittal contains information current as of October 15, 1992

Demolition wastes recycling; Reciclado de residuos de construccion y demolicion

Energy Technology Data Exchange (ETDEWEB)

Aguilar, A.; Monge, G. [INGURU Constructore, S.A. (Spain)

1995-06-01

This paper wants to show the up-to-date situation of demolition wastes from an international point of view. On the one hand it describes the different type of demolition wastes; on the other hand it explains the kind of treatment that is more adequate to each one. (Author)

22 CFR 121.11 - Military demolition blocks and blasting caps.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Military demolition blocks and blasting caps... blasting caps. Military demolition blocks and blasting caps referred to in Category IV(a) do not include the following articles: (a) Electric squibs. (b) No. 6 and No. 8 blasting caps, including electric...

Assessment of Soil, Surface-Water, and Ground-Water Contamination at Selected Sites at J-Field, Aberdeen Proving Ground, Maryland

National Research Council Canada - National Science Library

Phelan, Daniel

1998-01-01

.... From shortly after World War II into the 1970's, chemical-warfare agents, high-explosive munitions, and industrial chemicals were tested and disposed of at J-Field by open-pit burning and by high-explosive demolition...

Eksplozivne materije za neosetljiva ubojna sredstva / Explosive substances for insensitive munitions

Directory of Open Access Journals (Sweden)

Radun Jeremić

2005-03-01

Full Text Available U skladu sa sve strožim zahtevima za očuvanje životne sredine i većom bezbednošću, tendencije u razvoju suvremenih ubojnih sredstava (UbS, pored povećanja pouzdanosti i efikasnosti, usmerene su i na povećanje sigurnosti pri njihovoj proizvodnji, skladištenju, manipulaciji i upotrebi. Na taj način dobijena je nova kategorija UbS, tzv. neosetljiva UbS, kod kojih je verovatnoća neželjenog aktiviranja pod dejstvom spoljnih impulsa svedena na minimum. Suština rešavanja ovog problema je primena eksplozivnih materija koje su mnogo manje osetljive na spoljne uticaje u odnosu na standardne. Osnovni zahtev koji se pri tome postavlja je da taktičko-tehničke karakteristike ostanu na nivou ili budu bolje u odnosu na postojeća UbS. U radu je ukratko objašnjen koncept razvoja neosetljivih UbS i dat pregled najznačajnijih rezultata istraživanja u oblasti eksplozivnih materija koje zadovoljavaju zahteve za primenu u neosetljivim UbS. / According to severe environment protection and safety requirements, tendencies in development of modern munitions, besides of increasing reliability and efficiency, are directed to decreasing of danger during their processing, storing, handling and operating. In that manner the new category of munitions has been obtained, named insensitive munitions, with a minimum probability of unplanned activating. The best method for solving this problem is using of explosive substances that are more insensitive according to standard ones. The main requirement is the tactical and technical characteristics stay at the level or to be better according to the existing munitions. In this paper the developing concept of insensitive munitions is shortly explained and presented a review of most important research results of explosive materials that fulfill requirements for applying in insensitive munitions.

Environmental impacts of manufactured gas plant demolition: examples from site remediation experience

Energy Technology Data Exchange (ETDEWEB)

Unites, D. [Atlantic Environmental Services, Inc., Colchester, CT (United States)

1995-12-31

Inappropriate demolition of manufactured gas plant (MGP) sites may leave a continuing legacy in the environmental record. Much of the contamination encountered at former gas plants originated from on-site disposal or from spills and leaks during operations. However, some of the greatest potential for continual release comes from inappropriately decommissioned vessels and tanks. These structures contained liquids such as tars, oils, water, and other fluids associated with by-product removal or the gas stream purification process. Inorganic `solids` constitute another, although generally minor, source of contaminants during demolition. These contaminants include: cyanide- and sulfide-containing purifier materials; asbestos from roofing, pipe lagging, etc.; mercury from controls and manometers; and lead from painted surfaces. Normal elements of decommissioning and dismantling include: purging the piping system with inert gas; removal and sale of liquids having commercial value; disposal or abandonment of non-saleable liquids; scrapping and dismantling of above-grade metal vessels; abandonment of below-grade vessels; and demolition of above-grade buildings. Depending on the time from the cessation of operations to the demolition, some steps may have been omitted. Appropriate demolition would also take into account removal and disposal of asbestos, cyanide, lead, and mercury-containing materials prior to razing structures. By employing precautions during demolition, widespread contamination can be avoided and subsequent reuse of the site can be facilitated.

Green Residential Demolitions: Case Study of Vacant Land Reuse in Storm Water Management in Cleveland

Science.gov (United States)

The demolition process impacts how vacant land might be reused for storm water management. For five residential demolition sites (Cleveland, Ohio), an enhanced green demolition process was observed in 2012, and soil physical and hydrologic characteristics were measured predemolit...

Resolving the Role of the Dynamic Pressure in the Burial, Exposure, Scour, and Mobility of Underwater Munitions

Science.gov (United States)

Gilooly, S.; Foster, D. L.

2017-12-01

In nearshore environments, the motion of munitions results from a mixture of sediment transport conditions including sheet flow, scour, bedform migration, and momentary liquefaction. Incipient motion can be caused by disruptive shear stresses and pressure gradients. Foster et al. (2006) incorporated both processes into a single parameter, indicating incipient motion as a function of the bed state. This research looks to evaluate the role of the pressure gradient in positional state changes such as burial, exposure, and mobility. In the case of munitions, this may include pressure gradients induced by vortex shedding or the passing wave. Pressure-mapped model munitions are being developed to measure the orientation, rotation, and surface pressure of the munitions during threshold events leading to a new positional state. These munitions will be deployed in inner surf zone and estuary environments along with acoustic Doppler velocimeters (ADVs), pore water pressure sensors, a laser grid, and a pencil beam sonar with an azimuth drive. The additional instruments allow for near bed and far field water column and sediment bed sampling. Currently preliminary assessments of various pressure sensors and munition designs are underway. Two pressure sensors were selected; the thin FlexiForce A201 sensors will be used to indicate munition rolling during threshold events and diaphragm sensors will be used to understand changes in surrounding pore water pressure as the munition begins to bury/unbury. Both sensors are expected to give quantitative measurements of dynamic pressure gradients in the flow field surrounding the munition. Resolving the role of this process will give insight to an improved incipient motion parameter and allow for better munition motion predictions.

NDIA 2018 IM and EM Technology Symposium: Innovative Insensitive Munition Solutions for Enhanced Warfighter Effectiveness

Science.gov (United States)

2018-04-26

2018 IM & EM TECHNOLOGY SYMPOSIUM INNOVATIVE INSENSITIVE MUNITION SOLUTIONS FOR ENHANCED WARFIGHTER EFFECTIVENESS April 23 – 26, 2018 Doubletree by...IM & EM TECHNOLOGY SYMPOSIUM On behalf of the Insensitive Munitions and Energetic Materials Committee and our MSIAC partner, I would like to...welcome you to the 2018 Insensitive Munitions and Energetic Materials Technology Symposium. This international gathering of the top chemists, system

Decommissioning and demolition in the European Union. Current status

International Nuclear Information System (INIS)

Blohm-Hieber, Ute

2009-01-01

The European Commission pursues the environmental and energy policy goals of limiting global warming to a maximum of 2 C and, therefore, reducing CO 2 emissions by at least 20%. Nuclear power, with its present 30% contribution to the Community's electricity supply and the low CO 2 emissions of the entire fuel cycle, makes an important contribution to an energy mix matching the 3 factors of competitiveness, security of supply, and sustainability. The decision to use nuclear power plants in their respective countries for electricity production is left to each member state. As of mid-2008, 146 nuclear power plants were in operation in the European Union, while 74 had been shut down permanently. Two nuclear power plants had been demolished completely, showing that the European Community is just at the beginning of the learning curve in this field. The importance of nuclear power plant decommissioning and demolition will increase in the future as replacement capacity in nuclear power generation will become necessary. The European Commission's activities in decommissioning and demolition date from the 1990s: The provisions about environmental impact assessment and the recommendations to apply Article 37 (potential impacts on water, soil and air) of the Euratom Treaty demand a description of decommissioning and demolition of nuclear power plants. In a ruling of 2002, the European Court of Justice assigns to the Community the required competences in the fields of nuclear safety and, consequently, also decommissioning and demolition. The financial provisions necessary for these activities are covered in the Electricity Directive within the framework of the rules for a common single market in 2003. After a first status report, the Commission published recommendations about financing decommissioning and demolition in 2006. (orig.)

Cluster munitions: public health and international humanitarian law perspectives.

Science.gov (United States)

Freckelton, Ian

2008-02-01

As a result of civilian deaths in Vietnam, Cambodia, Laos, Chechnya, Kosovo, Afghanistan, Iraq and Lebanon, cluster munitions have been recognised to pose a grave threat to civilian populations because of their limited precision and problematically high rate of initial failure to explode. Efforts are intensifying to ban cluster munitions and to mandate those who have discharged them to defuse them effectively so as to reduce the risks to civilians. This editorial reviews these efforts and identifies a need for them to be actively supported by both the legal and medical communities.

Acoustic Scattering from Munitions in the Underwater Environment: Measurements and Modeling

Science.gov (United States)

Williams, K.; Kargl, S. G.; Espana, A.

2017-12-01

Acoustical scattering from elastic targets has been a subject of research for several decades. However, the introduction of those targets into the ocean environment brings new complexities to quantitative prediction of that scattering. The goal of our work has been to retain as much of the target physics as possible while also handling the propagation to and from the target in the multi-path ocean environment. Testing of the resulting predictions has been carried out via ocean experiments in which munitions are deployed on and within the sediment. We will present the overall philosophy used in the modeling and then compare model results to measurements. A 60 cm long 30 cd diameter aluminum cylinder will be used as a canonical example and then a sample of results for a variety of munitions will be shown. Finally, we will discuss the use of both the models and measurements in assessing the ability of sonar to discriminate munitions from other man-made targets. The difficulty of this challenge will be made apparent via results from a recent experiment in which both munitions and man-made "clutter" were deployed on a rippled sand interface.

Observation of Burial and Migration of Instrumented Surrogate Munitions Deployed in the Swash Zone

Science.gov (United States)

Cristaudo, D.; Puleo, J. A.; Bruder, B. L.

2017-12-01

Munitions (also known as unexploded ordnance; UXO) in the nearshore environment due to past military activities, may be found on the beach, constituting a risk for beach users. Munitions may be transported from offshore to shallower water and/or migrate along the coast. In addition, munitions may bury in place or be exhumed due to hydrodynamic forcing. Observations on munitions mobility have generally been collected offshore, while observations in the swash zone are scarce. The swash zone is the region of the beach alternately covered by wave runup where hydrodynamic processes may be intense. Studies of munitions mobility require the use of realistic surrogates to quantify mobility/burial and hydrodynamic forcing conditions. Four surrogates (BLU-61 Cluster Bomb, 81 mm Mortar, M151-70 Hydra Rocket and M107 155 mm High Explosive Howitzer) were developed and tested during large-scale laboratory and field studies. Surrogates house sensors that measure different components of motion. Errors between real munitions and surrogate parameters (mass, center of gravity and axial moment of inertia) are all within an absolute error of 20%. Internal munitions sensors consist of inertial motion units (for acceleration and angular velocity in and around the three directions and orientation), pressure transducers (for water depth above surrogate), shock recorders (for high frequency acceleration to detect wave impact on the surrogate), and an in-house designed array of optical sensors (for burial/exposure and rolling). An in situ array of sensors to measure hydrodynamics, bed morphology and sediment concentrations, was deployed in the swash zone, aligned with the surrogate deployment. Data collected during the studies will be shown highlighting surrogate sensor capabilities. Sensors response will be compared with GPS measurements and imagery from cameras overlooking the study sites of surrogate position as a function of time. Examples of burial/exposure and migration of surrogates

Trauma-related infections due to cluster munitions.

Science.gov (United States)

Fares, Youssef; El-Zaatari, Mohamad; Fares, Jawad; Bedrosian, Nora; Yared, Nadine

2013-12-01

Trauma-related infections remain a concerning and potentially avoidable complication of conflict-related injuries. During the Israeli conflict in South Lebanon, more than four million sub-munitions were dropped over South Lebanese soil. In this study, we will explore the different types of infection caused by sub-munitions and penetrating agents. This prospective study took place from 2006 to 2012 at the Lebanese University within the Faculty of Medical Sciences' departments. This study sample consisted of 350 injured casualties. Patients suffered from blast injuries with fragmentations targeting the head, face, torso, abdomen, pelvis and extremities. Of the 350 causalities studied, 326 (93.1%) were males, and 24 (6.9%) were females. Ages varied between 10 and 70 years, with the average age being 27 years. Of the 350 patients studied, 68 (19.4%) developed infections. Infections varied between pseudomonas, Escherichia coli, Candida and fungus and sometimes led to necrosis. Vaccinations, antibiotic therapies and proper wound irrigation must be performed at appropriate emergency units. Excision and complete debridement of necrotic and contaminated tissue should also be performed. The Convention on Cluster Munitions of 2008 should be adhered to, as these weapons indiscriminately and disproportionately harm civilians, thereby violating the well-established international principles governing conflict. Copyright © 2013 King Saud Bin Abdulaziz University for Health Sciences. Published by Elsevier Ltd. All rights reserved.

Hanford Patrol Academy Demolition Sites Closure Plan

International Nuclear Information System (INIS)

1992-11-01

From 1975 to 1991 the Hanford Patrol Academy Demolition Sites (HPADS) were used for demolition events. These demolition events were a form of thermal treatment for spent or abandoned chemical waste. Because the HPADS will no longer be used for this thermal activity, the sites will be closed. Closure will be conducted pursuant to the requirements of the Washington State Department of Ecology (Ecology) Dangerous Waste Regulations, Washington Administrative Code (WAC) 173-303-610 and 40 CFR 270.1. Closure also will satisfy closure requirements of WAC 173-303-680 and for the thermal treatment closure requirements of 40 CFR 265.381. This closure plan presents a description of the HPADS, the history of the waste treated, and the approach that will be followed to close the HPADS. Because dangerous waste does not include the source, special nuclear, and by-product material components of mixed waste, radionuclides are not within the scope of WAC 173-303 or of this closure plan. The information on radionuclides is provided only for general knowledge where appropriate. Only dangerous constituents derived from HPADS operations will be addressed in this closure plan in accordance with WAC 173-303-610(2)(b)(i). The HPADS are actually two distinct soil closure areas within the Hanford Patrol Academy training area

28 CFR 0.89 - Authority to seize arms and munitions of war.

Science.gov (United States)

2010-07-01

... war. 0.89 Section 0.89 Judicial Administration DEPARTMENT OF JUSTICE ORGANIZATION OF THE DEPARTMENT OF JUSTICE Federal Bureau of Investigation § 0.89 Authority to seize arms and munitions of war. The Director... arms and munitions of war, and other articles, pursuant to section 1 of title VI of the act of June 15...

Optimal path planning for video-guided smart munitions via multitarget tracking

Science.gov (United States)

Borkowski, Jeffrey M.; Vasquez, Juan R.

2006-05-01

An advent in the development of smart munitions entails autonomously modifying target selection during flight in order to maximize the value of the target being destroyed. A unique guidance law can be constructed that exploits both attribute and kinematic data obtained from an onboard video sensor. An optimal path planning algorithm has been developed with the goals of obstacle avoidance and maximizing the value of the target impacted by the munition. Target identification and classification provides a basis for target value which is used in conjunction with multi-target tracks to determine an optimal waypoint for the munition. A dynamically feasible trajectory is computed to provide constraints on the waypoint selection. Results demonstrate the ability of the autonomous system to avoid moving obstacles and revise target selection in flight.

Choosing a sustainable demolition waste management strategy using multicriteria decision analysis

International Nuclear Information System (INIS)

Roussat, Nicolas; Dujet, Christiane; Mehu, Jacques

2009-01-01

This paper presents an application of the ELECTRE III decision-aid method in the context of choosing a sustainable demolition waste management strategy for a case study in the city of Lyon, France. This choice of waste management strategy takes into consideration the sustainable development objectives, i.e. economic aspects, environmental consequences, and social issues. Nine alternatives for demolition waste management were compared with the aid of eight criteria, taking into account energy consumption, depletion of abiotic resources, global warming, dispersion of dangerous substances in the environment, economic activity, employment, and quality of life of the local population. The case study concerned the demolition of 25 buildings of an old military camp. Each alternative was illustrated with different waste treatments, such as material recovery, recycling, landfilling, and energy recovery. The recommended solution for sustainable demolition waste management for the case study is a selective deconstruction of each building with local material recovery in road engineering of inert wastes, local energy recovery of wood wastes, and specific treatments for hazardous wastes

Chemical Warfare Materiel in Sediment at a Deep-Water Discarded Military Munitions Site

Science.gov (United States)

Briggs, C. W.; Bissonnette, M. C.; Edwards, M.; Shjegstad, S. M.

2016-12-01

Understanding the release and transformation of chemical agent (CA) at underwater discarded military munitions (DMM) sites is essential to determine the potential risk to human health and impact on the ocean environment; yet few studies have been conducted at sites in excess of 250 m, the depth at which most U.S. CA munitions were disposed. Maritime construction workers installing cables or pipelines at a CA DMM site, as well as fishermen and scientific researchers deploying bottom-contact gear, represent possible exposure pathways to human receptors. The Hawai`i Undersea Military Munitions Assessment (HUMMA) sought to characterize a historic munitions sea-disposal site at depths between 400-650 m. During the 2014 HUMMA Sampling Survey, the Jason 2 remotely operated vehicle was used to collect sediments within two meters of suspected World War II chemical munitions, confirmed to be 100-lb M47 series bombs containing sulfur mustard. When environmental media was brought to the surface, samples were screened for distilled sulfur mustard (HD) and related agent breakdown products (ABP) (collectively referred to as chemical warfare materiel [CWM]). Detectable concentrations of HD and/or its ABP 1,4-dithiane were found in sediments collected at all CA DMM sites; HD was also detected at two control sites. The location and extent of munitions casing deterioration strongly influenced the distribution and level of CWM in sediment. The interior of the casing contained levels of CWM orders of magnitudes higher than that observed in the surrounding sediment at one meter distance, indicating the majority of the CWM is hydrolyzed as it is released from the munitions casing and a fraction of the fill materiel persists in the environment for decades following disposal. Although the potential for future site users to become exposed to CWA in recovered sediments and debris exists, the level of risk is significantly mitigated by the depth and location of the sea-disposal site.

The FRJ-1 (MERLIN) research reactor: its main activity inventory has been removed by successful demolition of the reactor block; Forschungsreaktor FRJ-1 (MERLIN) - Das Hauptaktivitaetsinventar ist durch erfolgreichen Rueckbau des Reaktorblocks entfernt

Energy Technology Data Exchange (ETDEWEB)

Stahn, B.; Printz, R.; Matela, K.; Zehbe, C. [Forschungszentrum Juelich GmbH, Juelich (Germany); Poeppinghaus, J. [Gesellschaft fuer Nuklear-Service mbH, Essen (Germany); Cremer, J. [Siempelkamp Nukleartechnik GmbH, Heidelberg (Germany)

2004-02-01

The FRJ-1 (MERLIN) research reactor was decommissioned in 1985 after twenty-three years of operation. Demolition of the plant was begun in 1996. The article contains a survey of the demolition steps carried out so far within the framework of three partial permits. The main activity is the demolition of the reactor core structures as a precondition for subsequent measures to ensure clearance measurements of the building. The core structures are demolished which were exposed to high neutron fluxes during reactor operation and now show the highest activity and dose rate levels, except for the core internals. For demolition and disassembly of the metal structures in this part of the plant, the tools specially designed and made include a remotely operated sawing system and a pipe cutting system for internal segmentation of the beam lines. The universal demolition tool for use also above and beyond the concrete structures has been found to be a remotely controlled electrohydraulic demolition shovel. Spreading contamination in the course of the demolition work was avoided. One major reason for this success was the fact that no major airborne contamination existed at any time as a consequence of the quality of the material demolished and also of the consistent use of technical tools. While the reactor block was being demolished, an application for clearance measurement of the reactor hall and subsequent release from the scope of the Atomic Energy Act was filed as early as in mid-2003. The fourth partial permit covering these activities is expected to be issued in the spring of 2004. (orig.)

High-power VCSELs for smart munitions

Science.gov (United States)

Geske, Jon; MacDougal, Michael; Cole, Garrett; Snyder, Donald

2006-08-01

The next generation of low-cost smart munitions will be capable of autonomously detecting and identifying targets aided partly by the ability to image targets with compact and robust scanning rangefinder and LADAR capabilities. These imaging systems will utilize arrays of high performance, low-cost semiconductor diode lasers capable of achieving high peak powers in pulses ranging from 5 to 25 nanoseconds in duration. Aerius Photonics is developing high-power Vertical-Cavity Surface-Emitting Lasers (VCSELs) to meet the needs of these smart munitions applications. The authors will report the results of Aerius' development program in which peak pulsed powers exceeding 60 Watts were demonstrated from single VCSEL emitters. These compact packaged emitters achieved pulse energies in excess of 1.5 micro-joules with multi kilo-hertz pulse repetition frequencies. The progress of the ongoing effort toward extending this performance to arrays of VCSEL emitters and toward further improving laser slope efficiency will be reported.

Hanford Patrol Academy demolition sites closure plan

Energy Technology Data Exchange (ETDEWEB)

1993-09-30

The Hanford Site is owned by the U.S. Government and operated by the U.S. Department of Energy, Richland Operations Office. Westinghouse Hanford Company is a major contractor to the U.S. Department of Energy, Richland Operations Office and serves as co-operator of the Hanford Patrol Academy Demolition Sites, the unit addressed in this paper. This document consists of a Hanford Facility Dangerous Waste Part A Permit Application, Form 3 (Revision 4), and a closure plan for the site. An explanation of the Part A Form 3 submitted with this closure plan is provided at the beginning of the Part A section. This Hanford Patrol Academy Demolition Sites Closure Plan submittal contains information current as of December 15, 1994.

Recycling the construction and demolition waste to produce polymer concrete

Science.gov (United States)

Hamza, Mohammad T.; Hameed, Awham M., Dr.

2018-05-01

The sustainable management for solid wastes of the construction and demolition waste stimulates searching for safety applications for these wastes. The aim of this research is recycling of construction and demolition waste with some different types of polymeric resins to be used in manufacturing process of polymer mortar or polymer concrete, and studying their mechanical and physical properties, and also Specify how the values of compressive strength and the density are affected via the different parameters. In this research two types of construction and demolition waste were used as aggregates replacement (i.e. waste cement/concrete debris, and the waste blocks) while the two types of polymer resins (i.e. Unsaturated polyester and Epoxy) as cement replacements. The used weight percentages of the resins were changed within (1°, 20, 25 and 30) % to manufacture this polymer concrete.

Influence of construction and demolition waste management on the environmental impact of buildings

International Nuclear Information System (INIS)

Coelho, André; Brito, Jorge de

2012-01-01

Highlights: ► Environmental impacts of different demolition practices. ► “Top-down” approach to the Life Cycle Analysis methodology. ► Results based on real buildings measurements and demolition contractor activities. ► Not every type of selective demolition brings about environmental benefits. - Abstract: The purpose of this study is to quantify comparable environmental impacts within a Life Cycle Analysis (LCA) perspective, for buildings in which the first (Materials) and last (End of Life) life cycle stages are adjusted to several waste/material management options. Unlike most LCAs, the approach is “top-down” rather than “bottom-up”, which usually involves large amounts of data and the use of specific software applications. This approach is considered appropriate for a limited but expedient LCA designed to compare the environmental impacts of different life cycle options. Present results, based on real buildings measurements and demolition contractor activities, show that shallow, superficial, selective demolition may not result in reduced environmental impacts. Calculations actually show an increase (generally less than 5%) in most impact categories for the Materials and End of Life stages because of extra transportation needs. However, core material separation in demolition operations and its recycling and/or reuse does bring environmental benefits. A reduction of around 77% has been estimated in the climate change impact category, 57% in acidification potential and 81% in the summer smog impact (for the life cycle stages referred).

Remote Machining and Evaluation of Explosively Filled Munitions

Data.gov (United States)

Federal Laboratory Consortium — This facility is used for remote machining of explosively loaded ammunition. Munition sizes from small arms through 8-inch artillery can be accommodated. Sectioning,...

The Effects of Data Collection Method and Monitoring of Workers’ Behavior on the Generation of Demolition Waste

Directory of Open Access Journals (Sweden)

Gi-Wook Cha

2017-10-01

Full Text Available The roles of both the data collection method (including proper classification and the behavior of workers on the generation of demolition waste (DW are important. By analyzing the effect of the data collection method used to estimate DW, and by investigating how workers’ behavior can affect the total amount of DW generated during an actual demolition process, it was possible to identify strategies that could improve the prediction of DW. Therefore, this study surveyed demolition waste generation rates (DWGRs for different types of building by conducting on-site surveys immediately before demolition in order to collect adequate and reliable data. In addition, the effects of DW management strategies and of monitoring the behavior of workers on the actual generation of DW were analyzed. The results showed that when monitoring was implemented, the estimates of DW obtained from the DWGRs that were surveyed immediately before demolition and the actual quantities of DW reported by the demolition contractors had an error rate of 0.63% when the results were compared. Therefore, this study has shown that the proper data collection method (i.e., data were collected immediately before demolition applied in this paper and monitoring on the demolition site have a significant impact on waste generation.

OPERATIONAL LIMITATIONS FOR DEMOLITION OF A HIGHLY ALPHA CONTAMINATED BUILDING MODLES VERSUS MEASURED AIR & SURFACE ACTIVITY CONCENTRATIONS

Energy Technology Data Exchange (ETDEWEB)

LLOYD, E.R.

2006-11-02

The demolition of a facility historically used for processing and handling transuranic materials is considered. Residual alpha emitting radionuclide contamination poses an exposure hazard if released to the local environment during the demolition. The process of planning for the demolition of this highly alpha contaminated building, 232-Z, included a predemolition modeling analysis of potential exposures. Estimated emission rates were used as input to an air dispersion model to estimate frequencies of occurrence of peak air and surface exposures. Postdemolition modeling was also conducted, based on the actual demolition schedule and conditions. The modeling results indicated that downwind deposition is the main operational limitation for demolition of a highly alpha-contaminated building. During the demolition of 232-Z, airborne radiation and surface contamination were monitored. The resultant non-detect monitoring results indicate a significant level of conservatism in the modeled results. This comparison supports the use of more realistic assumption in the estimating emission rates. The resultant reduction in modeled levels of potential exposures has significant implications in terms of the projected costs of demolition of such structures.

40 CFR 266.203 - Standards applicable to the transportation of solid waste military munitions.

Science.gov (United States)

2010-07-01

... transportation of solid waste military munitions. 266.203 Section 266.203 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS... applicable to the transportation of solid waste military munitions. (a) Criteria for hazardous waste...

40 CFR 266.205 - Standards applicable to the storage of solid waste military munitions.

Science.gov (United States)

2010-07-01

... solid waste military munitions. 266.205 Section 266.205 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) SOLID WASTES (CONTINUED) STANDARDS FOR THE MANAGEMENT OF SPECIFIC HAZARDOUS... applicable to the storage of solid waste military munitions. (a) Criteria for hazardous waste regulation of...

Validation of Passive Sampling Devices for Monitoring of Munitions Constituents in Underwater Environments

Science.gov (United States)

2017-06-30

Research and Development Program [SERDP] project #ER-2542) into the canister would provide enhancement of the quantitative estimation of the TWA...Department of Defense EOD Explosive Ordnance Disposal EPA United States Environmental Protection Agency EQL Environmental Quantitation Limit EST...Laboratory Quantitation Limit MC Munitions Constituents mL Milliliter MR Munitions Response NESDI Navy’s Environmental Security Development to

Use of filler limestone and construction and demolition residues for remediating soils contaminated with heavy metals: an assessment by means of plant uptake.

Science.gov (United States)

Banegas, Ascension; Martinez-Sanchez, Maria Jose; Agudo, Ines; Perez-Sirvent, Carmen

2010-05-01

A greenhouse trial was carried out to evaluate the assimilation of heavy metals by three types of horticultural plants (lettuce, broccoli and alfalfa), different parts of which are destined for human and animal consumption (leaves, roots, fruits). The plants were cultivated in four types of soil, one uncontaminated (T1), one soil collected in the surrounding area of Sierra Minera (T2), the third being remediated with residues coming from demolition and construction activities (T3) and the four remediated with filler limestone (T4). To determine the metal content, soil samples were first ground to a fine powder using an agate ball mill. Fresh vegetable samples were separated into root and aboveground biomass and then lyophilized. The DTPA-extractable content was also determined to calculate the bioavailable amount of metal. Finally, the translocation factor (TF) and bioconcentration factor (BCF) were calculated. Arsenic levels were obtained by using atomic fluorescence spectrometry with an automated continuous flow hydride generation (HG-AFS) spectrometer and Cd, Pb and Zn was determined by electrothermal atomization atomic absorption spectrometry (ETAAS) or flame atomic absorption spectrometry (FAAS). Samples of the leached water were also obtained and analyzed. According to our results, the retention of the studied elements varies with the type of plant and is strongly decreased by the incorporation of filler limestone and/or construction and demolition residues to the soils. This practice represents a suitable way to reduce the risk posed to the biota by the presence of high levels of heavy metal in soil.

Demolition of the FRJ-1 research reactor (MERLIN)

International Nuclear Information System (INIS)

Stahn, B.; Matela, K.; Zehbe, C.; Poeppinghaus, J.; Cremer, J.

2003-01-01

FRJ-2 (MERLIN), the swimming pool reactor cooled and moderated by light water, was built at the then Juelich Nuclear Research Establishment (KFA) between 1958 and 1962. In the period between 1964 and 1985, it was used for. The reactor was decommissioned in 1985. Since 1996, most of the demolition work has been carried out under the leadership of a project team. The complete secondary cooling system was removed by late 1998. After the cooling loops and experimental installations had been taken out, the reactor vessel internals were removed in 2000 after the water had been drained from the reactor vessel. After the competent authority had granted a license, demolition of the reactor block, the central part of the research reactor, was begun in October 2001. In a first step, the reactor operating floor and the reactor attachment structures were removed by the GNS/SNT consortium charged with overall planning and execution of the job. This phase gave rise to approx. The reactor block proper is dismantled in a number of steps. A variety of proven cutting techniques are used for this purpose. Demolition of the reactor block is to be completed in the first half of 2003. (orig.) [de

Progressively safer, cheaper demolition of Fernald

International Nuclear Information System (INIS)

Nichols, Robert; Pennington, Norman

2000-01-01

Fluor Fernald, Inc. has been progressively improving Decontamination and Dismantlement (D and D) at the Department of Energy's Fernald Environmental Management Project by applying new technologies and better methodologies to the work. Demolition issues existed in the past that necessitated new or improved solutions to maintain worker safety, protect the environment and accomplish the work in a cost effective manner. Lessons learned from D and D of 80 structures has led to a systematic approach, which can be implemented in various D and D arenas. When facility production was halted, hold-up material and process residues remained in the process piping and components. Over 500,000 pounds of material was removed by workers who completed the tasks two years ahead of schedule, $7 million under budget and with an excellent safety record. This success was the result of detailed planning and irdision of lessons learned as work progressed from facility to facility. Work sequences were developed that reduced airborne contamination. Demolition of structures has been performed at Fernald by carefully selected and qualified subcontractors. Asbestos and lead abatement, equipment, piping and conduit removal, and structural demolition have been completed to progressively higher performance specifications developed by Fluor Fernald based on lessons learned during execution. Safety continues to be the primary consideration in performing potentially hazardous work. Technologies such as hydraulic shears have been developed and used to keep workers away from danger. A new technology, ''Cool Suits,'' has been demonstrated to help prevent heat stress when anti-contamination clothing is required in elevated temperature working conditions. For tall structures, implosion technologies have been employed with progressively improved results, Several other new technologies have been evaluated by Fluor Fernald and applied by subcontractors. The improved technologies included the oxy-gas torch

Characterizing the environmental impact of metals in construction and demolition waste.

Science.gov (United States)

Yu, Danfeng; Duan, Huabo; Song, Qingbin; Li, Xiaoyue; Zhang, Hao; Zhang, Hui; Liu, Yicheng; Shen, Weijun; Wang, Jinben

2018-05-01

Large quantities of construction and demolition (C&D) waste are generated in China every year, but their potential environmental impacts on the surrounding areas are rarely assessed. This study focuses on metals contained in C&D waste, characterizing the metal concentrations and their related environmental risks. C&D waste samples were collected in Shenzhen City, China, from building demolition sites, renovation areas undergoing refurbishment, landfill sites, and recycling companies (all located in Shenzhen city) that produce recycled aggregate, in order to identify pollution levels of the metals As, Cd, Cr, Cu, Pb, Ni, and Zn. The results showed that (1) the metal concentrations in most demolition and renovation waste samples were below the soil environmental quality standard for agricultural purposes (SQ-Agr.) in China; (2) Cd, Cu, and Zn led to relatively higher environmental risks than other metals, especially for Zn (DM5 tile sample, 360 mg/kg; R4 tile sample, 281 mg/kg); (3) non-inert C&D waste such as wall insulation and foamed plastic had high concentrations of As and Cd, so that these materials required special attention for sound waste management; and (4) C&D waste collected from landfill sites had higher concentrations of Cd and Cu than did waste collected from demolition and refurbishment sites.

Pilot-based assessment of the economics of recycling construction demolition waste.

Science.gov (United States)

Srour, Issam M; Chehab, Ghassan R; El-Fadel, Mutasem; Tamraz, Sandy

2013-11-01

The significant amount of waste generated from construction demolition has become a chronic problem in many developing countries. Using data obtained from demolition contractors and various other sources, this paper proposes a framework for proper handling of construction demolition waste (CDW) to serve as a decision support tool in countries suffering from the lack of national CDW management guidelines. The framework is then demonstrated through a case study in the city of Beirut, Lebanon, and a sensitivity analysis is carried out to examine the economic feasibility of developing a recycling facility. The analysis showed that in order for a facility to be feasible, a gate fee should be charged in the presence of a market for recycled aggregates. The results confirm the significance of instigating and implementing legislation to control illegal dumping, constructing, and managing engineered landfills, and establishing markets for recycled CDW.

Application of Updated Construction and Demolition Waste Reduction Policy to Army Projects

Science.gov (United States)

2015-12-01

recovering materials for reuse and recycling from demolition, new construction, and renovation and repurposing projects. In its efforts to improve the...Building contents; reuse and recycling potential (including the follow- ing specific materials, products and components that are potentially re- usable...conventional demolition. Implement deconstruction wherever markets or on-site reuse opportunities exist or are anticipated.  Page 24, 3-7 REDUCE

Munition Burial by Local Scour and Sandwaves: large-scale laboratory experiments

Science.gov (United States)

Garcia, M. H.

2017-12-01

Our effort has been the direct observation and monitoring of the burial process of munitions induced by the combined action of waves, currents and pure oscillatory flows. The experimental conditions have made it possible to observe the burial process due to both local scour around model munitions as well as the passage of sandwaves. One experimental facility is the Large Oscillating Water Sediment Tunnel (LOWST) constructed with DURIP support. LOWST can reproduce field-like conditions near the sea bed. The second facility is a multipurpose wave-current flume which is 4 feet (1.20 m) deep, 6 feet (1.8 m) wide, and 161 feet (49.2 m) long. More than two hundred experiments were carried out in the wave-current flume. The main task completed within this effort has been the characterization of the burial process induced by local scour as well in the presence of dynamic sandwaves with superimposed ripples. It is found that the burial of a finite-length model munition (cylinder) is determined by local scour around the cylinder and by a more global process associated with the formation and evolution of sandwaves having superimposed ripples on them. Depending on the ratio of the amplitude of these features and the body's diameter (D), a model munition can progressively get partially or totally buried as such bedforms migrate. Analysis of the experimental data indicates that existing semi-empirical formulae for prediction of equilibrium-burial-depth, geometry of the scour hole around a cylinder, and time-scales developed for pipelines are not suitable for the case of a cylinder of finite length. Relative burial depth (Bd / D) is found to be mainly a function of two parameters. One is the Keulegan-Carpenter number, KC, and the Shields parameter, θ. Munition burial under either waves or combined flow, is influenced by two different processes. One is related to the local scour around the object, which takes place within the first few hundred minutes of flow action (i.e. short

U.S. Army Training and Testing Area Carrying Capacity (ATTACC) for Munitions (AFM)

Science.gov (United States)

2006-11-01

Army Training Support Center USDA United States Department of Agriculture USGS United States Geological Survey USLE Universal Soil Loss Equation...Range condition is a function of climate, soil , and hydrology. The munitions impact, constituent load, and range condition are modeled using AFM...For ArcGIS v2 to attain expected concentrations of munitions constituents and corresponding risk due to exposure through soil - and water-related

PROJECT EXPERIENCE REPORT DEMOLITION OF HANFORDS 233-S PLUTONIUM CONCENTRATION FACILITY

International Nuclear Information System (INIS)

BERLIN, G.T.; ORGILL, T.K.

2004-01-01

This report provides a summary of the preparation, operations, innovative work practices, and lessons learned associated with demolition of the 2334 Plutonium Concentration Facility. This project represented the first open-air demolition of a highly-contaminated plutonium facility at the Hanford Site. This project may also represent the first plutonium facility in the US. Department of Energy (DOE) complex to have been demolished without first decontaminating surfaces to near ''free release'' standards. Demolition of plutonium contaminated structures, if not properly managed, can subject cleanup personnel and the environment to significant risk. However, with proper sequencing and innovative use of commercially available equipment, materials, and services, this project demonstrated that a plutonium processing facility can be demolished while avoiding the need to perform extensive decontamination or to construct large enclosures. This project utilized an excavator with concrete shears, diamond circular saws, water misting and fogging equipment, commercially available fixatives and dust suppressants, conventional mobile crane and rigging services, and near real-time modeling of meteorological and radiological conditions. Following a significant amount of preparation, actual demolition of the 233-S Facility began in October 2003 and was completed in late April 2004. The knowledge and experience gained on this project are important to the Hanford Site as additional plutonium processing facilities are scheduled for demolition in the near future. Other sites throughout the DOE Complex may also be faced with similar challenges. Numerous innovations and effective work practices were implemented on this project. Accordingly, a series of ''Lessons Learned and Innovative Practices Fact Sheets'' were developed and are included as an appendix to this report. This collection of fact sheets is not intended to capture every innovative work practice and lesson learned, but rather

PROJECT EXPERIENCE REPORT DEMOLITION OF HANFORDS 233-S PLUTONIUM CONCENTRATION FACILITY

International Nuclear Information System (INIS)

BERLIN, G.T.

2004-01-01

This report provides a summary of the preparation, operations, innovative work practices, and lessons learned associated with demolition of the 2334 Plutonium Concentration Facility. This project represented the first open-air demolition of a highly-contaminated plutonium facility at the Hanford Site. This project may also represent the first plutonium facility in the US. Department of Energy (DOE) complex to have been demolished without first decontaminating surfaces to near ''free release'' standards. Demolition of plutonium contaminated structures, if not properly managed, can subject cleanup personnel and the environment to significant risk. However, with proper sequencing and innovative use of commercially available equipment, materials, and services, this project demonstrated that a plutonium processing facility can be demolished while avoiding the need to perform extensive decontamination or to construct large enclosures. This project utilized an excavator with concrete shears, diamond circular saws, water misting and fogging equipment, commercially available fixatives and dust suppressants, conventional mobile crane and rigging services, and near real-time modeling of meteorological and radiological conditions. Following a significant amount of preparation, actual demolition of the 2333 Facility began in October 2003 and was completed in late April 2004. The knowledge and experience gained on this project are important to the Hanford Site as additional plutonium processing facilities are scheduled for demolition in the near future. Other sites throughout the DOE Complex may also be faced with similar challenges. Numerous innovations and effective work practices were implemented on this project. Accordingly, a series of ''Lessons Learned and Innovative Practices Fact Sheets'' were developed and are included as an appendix to this report. This collection of fact sheets is not intended to capture every innovative work practice and lesson learned, but rather to

Concrete decontamination and demolition methods

International Nuclear Information System (INIS)

LaGuardia, T.S.

1980-01-01

The US Department of Energy (DOE), Division of Environmental Control Technology, requested Nuclear Energy Services to prepare a handbook for the decontamination and decommissioning (D and D) of DOE-owned and commercially-owned radioactive facilities. the objective of the handbook is to provide the nuclear industry with guidance on the state-of-the-art methods and equipment available for decommissioning and to provide the means to estimate decommissioning costs and environmental impact. The methods available for concrete decontamination and demolition are summarized to provide an overview of some of the state-of-the-art techniques to be discussed at this workshop. The pertinent information on each method will include the selection factors such as the rate of performance in terms of concrete removal per unit time (cubic yards per day), manpower required by craft, unit cost (dollars per cubic yard) and the advantages and disadvantages. The methods included in this overview are those that have been routinely used in nuclear and nonnuclear applications or demonstrated in field tests. These methods include controlled blasting, wrecking ball or slab, backhoe mounted ram, flame torch, thermic lance, rock splitter, demolition compound, sawing, core stitch drilling, explosive cutting, paving breaker and power chisel, drill and spall, scarifying, water cannon and grinding

Construction and Demolition Waste

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Andersen, L.

2011-01-01

Construction and demolition waste (C&D waste) is the waste generated during the building, repair, remodeling or removal of constructions. The constructions can be roads, residential housing and nonresidential buildings. C&D waste has traditionally been considered without any environmental problems...... should be managed accordingly. Another reason is that it has been documented that a large fraction of C&D waste (about 90 %) can be easily recycled and thus can conserve landfill capacity. C&D waste may conveniently be divided into three subcategories: Buildings, roads and excavations. This chapter...

Service life determination of munition during expeditionary missions

NARCIS (Netherlands)

Klerk, W.P.C. de; Heijden, A.E.D.M. van der

2012-01-01

For a more in-depth understanding of the aging processes of munitions in expeditionary operations, research is performed with respect to the influence of transport, storage and use on the safety of ammunition. Within this programme the influences of parameters like temperature, humidity, vibrations,

Distribution of chemical warfare agent, energetics, and metals in sediments at a deep-water discarded military munitions site

Science.gov (United States)

Briggs, Christian; Shjegstad, Sonia M.; Silva, Jeff A. K.; Edwards, Margo H.

2016-06-01

There is a strong need to understand the behavior of chemical warfare agent (CWA) at underwater discarded military munitions (DMM) sites to determine the potential threat to human health or the environment, yet few studies have been conducted at sites in excess of 250 m, the depth at which most U.S. chemical munitions were disposed. As part of the Hawai'i Undersea Military Munitions Assessment (HUMMA), sediments adjacent to chemical and conventional DMM at depths of 400-650 m were sampled using human occupied vehicles (HOVs) in order to quantify the distribution of CWA, energetics, and select metals. Sites in the same general area, with no munitions within 50 m in any direction were sampled as a control. Sulfur mustard (HD) and its degradation product 1,4-dithiane were detected at each CWA DMM site, as well as a single sample with the HD degradation product 1,4-thioxane. An energetic compound was detected in sediment to a limited extent at one CWA DMM site. Metals common in munitions casings (i.e., Fe, Cu, and Pb) showed similar trends at the regional and site-wide scales, likely reflecting changes in marine sediment deposition and composition. This study shows HD and its degradation products can persist in the deep-marine environment for decades following munitions disposal.

Remediation and demolition of coke by-products plants

Energy Technology Data Exchange (ETDEWEB)

Stiffler, M A; Gould, W C

1992-08-01

The programme undertaken by ICF Kaiser Engineers and LTV Steel Co. to clean up and demolish four closed coking plants is described, including PCB removal, asbestos abatement, pipe removal and cleaning, tank cleaning, demolition and soil bioremediation. Costs are discussed.

Environmental and economical feasibility of selective demolition project; Viabilidad ambiental y economica de un proyecto de demolicion selectiva: hacia una optima gestion de los RCD

Energy Technology Data Exchange (ETDEWEB)

Vegas, I.

2004-07-01

Selective demolition practices have not yet become popular in our country. Unlike conventional demolition practices, selective demolition helps to increase the amount of components to be reused or materials to be recycled. Thus, the percentage of demolition waste deposited in landfills can be reduced, and the production of recycled materials with optimum quality is fostered. Taking the case study of selective demolition carried out in the municipally of Lasarte-Oria (Basque Country-Spain) as its basis, this paper presents an economic and environmental analysis of the same. Likewise, the economic costs deriving from selective demolition are compared with analogous costs from conventional demolition with an aim to establishing the ideal frame supporting economically feasible selective demolition. (Author)

GIS-based planning system for managing the flow of construction and demolition waste in Brazil.

Science.gov (United States)

Paz, Diogo Henrique Fernandes da; Lafayette, Kalinny Patrícia Vaz; Sobral, Maria do Carmo

2018-05-01

The objective of this article was to plan a network for municipal management of construction and demolition waste in Brazil with the assistance of a geographic information system, using the city of Recife as a case study. The methodology was carried out in three stages. The first was to map the illegal construction and demolition of waste disposal points across Recife and classify the waste according to its recyclability. In sequence, a method for indicating suitable areas for installation of voluntary delivery points, for small waste generators, are presented. Finally, a method for indicating suitable areas for the installation of trans-shipment and waste sorting areas, developed for large generators, is presented. The results show that a geographic information system is an essential tool in the planning of municipal construction and demolition waste management, in order to facilitate the spatial analysis and control the generation, sorting, collection, transportation, and final destination of construction and demolition waste, increasing the rate of recovery and recycling of materials.

Construction and Demolition Waste Characteristics in Tanzania ...

African Journals Online (AJOL)

The construction industry generates a lot of construction and demolition (C&D) waste which puts some challenges to its management. For example, currently, in many towns in Tanzania, there are no landfill sites for solid waste disposal; and as a consequence open air dumping sites are used. Dumping C&D waste puts ...

Bioaccumulation of chemical warfare agents, energetic materials, and metals in deep-sea shrimp from discarded military munitions sites off Pearl Harbor

Science.gov (United States)

Koide, Shelby; Silva, Jeff A. K.; Dupra, Vilma; Edwards, Margo

2016-06-01

The bioaccumulation of munitions-related chemicals at former military deep-water disposal sites is poorly understood. This paper presents the results of human-food-item biota sampling to assess the potential for bioaccumulation of chemical warfare agents, energetic materials, arsenic, and additional munitions-related metals in deep-sea shrimp tissue samples collected during the Hawai'i Undersea Military Munitions Assessment (HUMMA) project to date. The HUMMA investigation area is located within a former munitions sea-disposal site located south of Pearl Harbor on the island of O'ahu, Hawai'i, designated site Hawaii-05 (HI-05) by the United States Department of Defense. Indigenous deep-sea shrimp (Heterocarpus ensifer) were caught adjacent to discarded military munitions (DMM) and at control sites where munitions were absent. Tissue analysis results showed that chemical warfare agents and their degradation products were not present within the edible portions of these samples at detectable concentrations, and energetic materials and their degradation products were detected in only a few samples at concentrations below the laboratory reporting limits. Likewise, arsenic, copper, and lead concentrations were below the United States Food and Drug Administration's permitted concentrations of metals in marine biota tissue (if defined), and their presence within these samples could not be attributed to the presence of DMM within the study area based on a comparative analysis of munitions-adjacent and control samples collected. Based on this current dataset, it can be concluded that DMM existing within the HUMMA study area is not contributing to the bioaccumulation of munitions-related chemicals for the biota species investigated to date.

48 CFR 225.770 - Prohibition on acquisition of United States Munitions List items from Communist Chinese military...

Science.gov (United States)

2010-10-01

... 48 Federal Acquisition Regulations System 3 2010-10-01 2010-10-01 false Prohibition on acquisition of United States Munitions List items from Communist Chinese military companies. 225.770 Section 225... of United States Munitions List items from Communist Chinese military companies. This section...

Quantities of arsenic-treated wood in demolition debris generated by Hurricane Katrina.

Science.gov (United States)

Dubey, Brajesh; Solo-Gabriele, Helena M; Townsendt, Timothy G

2007-03-01

The disaster debris from Hurricane Katrina is one of the largest in terms of volume and economic loss in American history. One of the major components of the demolition debris is wood waste of which a significant proportion is treated with preservatives, including preservatives containing arsenic. As a result of the large scale destruction of treated wood structures such as electrical poles, fences, decks, and homes a considerable amount of treated wood and consequently arsenic will be disposed as disaster debris. In this study an effort was made to estimate the quantity of arsenic disposed through demolition debris generated in the Louisiana and Mississippi area through Hurricane Katrina. Of the 72 million cubic meters of disaster debris generated, roughly 12 million cubic meters were in the form of construction and demolition wood resulting in an estimated 1740 metric tons of arsenic disposed. Management of disaster debris should consider the relatively large quantities of arsenic associated with pressure-treated wood.

Stripping demolition of reinforced concrete by electric heating method

International Nuclear Information System (INIS)

Nakagawa, Wahei; Nishita, Kiwamu; Kasai, Yoshio

1993-01-01

The present paper describes the procedures and results of a series of experiments the authors conducted to verify the efficiency of the electric heating method, previously proposed for so-called stripping demolition by applying electric current through reinforcing bars. In this method, a low voltage high current is run from one end to the other of a reinforcing bar or bars existing in a concrete structure, inducing intense heat in the bar(s) which in its turn brings about cracks in the surrounding concrete mass, facilitating secondary demolition by hammer picks or other means. The experiments were performed on full-scale biological shield wall mock-ups of a BWR and a small reactor. The results of the experiments are summarized as follows. (1) When electric current is applied through reinforcing bars, the bond between concrete and bars is loosened, and cracks start from one bar and progress toward other bars. Under appropriate conditions, the cracks in concrete run from the contact surface at one bar all the way to its the contact surface on another bar. (2) Cracks appear and grow only between two electrodes between which current is applied, not extending out of the area thus defined. (3) The concrete in the region closer to a current-bearing bar is intensely heated, whereas the concrete far from the bars remains nearly unheated. (4) Concrete walls after electric heating of bars disintegrates, if demolished with hammers, with the covering concrete are removed from the remaining portion of the structure together with heated bars, in shapes of flakes. (5) The reinforced concrete collapses in massive pieces of concrete, without generating much dust as is the case with the demolition of a concrete structure not heated by electricity. Results of the experiments show that the electric heating method is worth applying also to the demolition of nuclear power plants where concrete in the radioactivated surface region of shield walls needs to be stripped off in flakes

Does demolition or refurbishment of old and inefficient homes help to increase our environmental, social and economic viability?

International Nuclear Information System (INIS)

Power, Anne

2008-01-01

The issue of whether to demolish or refurbish older housing has been debated for over a century. It has been an active policy area since the late 1880s, when the Government first authorised the statutory demolition of insanitary slums. In the 1960s, revulsion at the scale of 'demolition blight' and new building caused a rethink, leading to a major reinvestment in inner city neighbourhoods of older housing. In the past 5 years, debate on demolition and new building has been intensified by the Government's Sustainable Communities Plan of 2003, with its proposals for large-scale clearance and building. Environmental arguments about renovating the existing stock have gained increasing prominence as people have sought to defend their communities from demolition. The evidence on whether demolition would reduce the amount of greenhouse gases we emit into the atmosphere is unclear and disputed. This paper summarises the evidence and arguments, and attempts to clarify the most realistic, achievable route to major reductions in energy use in homes

Asbestos exposure among construction workers during demolition of old houses in Tehran, Iran.

Science.gov (United States)

Kakooei, Hossein; Normohammadi, Mohhammad

2014-01-01

Air quality in demolition practices has seldom been evaluated in Iran. Accordingly, we evaluated asbestos exposure among Tehran construction workers during the demolition of old houses. To identify possible sources of asbestos exposure, including thermal insulations, chimney pipes and cement sheets, were all sampled. This study also were taken the personal air samples to evaluate any asbestos exposure during the demolition. The asbestos fibers found in the samples were analyzed by phase-contrast optical microscopy (PCM), scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analysis, and polarized light microscopy (PLM) methods. Personal monitoring of asbestos fiber levels indicated a range from 0.01 to 0.15 PCM f/ml (0.02-0.42 SEM f/ml). The geometric mean concentrations were 0.07 PCM f/ml (0.20 SEM f/ml), which is considerably higher than the threshold limit value (TLV) proposed by American Conference of Governmental Industrial Hygienist (ACGIH), which is 0.1 f/ml. The analysis showed a presence in the bulk samples only chrysotile asbestos and an absence of the other type asbestos. Therefore, it might be expected that workers who worked in the demolition of old houses will suffer from negative effects of exposing to the asbestos fibers.

The End of the Line, Preparing the Main Plant Process Building for Demolition at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Rowell, L.E.; Kurasch, D.H.; Hackett, M.; Gorsuch, G.; Sullivan, D.W.

2009-01-01

The West Valley Demonstration Project (WVDP) Act of 1980 authorized the Department of Energy to conduct a high-level radioactive waste management demonstration project at the site of the former Spent Fuel Reprocessing Plant in West Valley, New York to demonstrate solidification techniques to prepare high-level liquid waste for disposal. The reprocessing facility at this site was the only commercial NRC-licensed spent fuel reprocessing plant to have operated in the United States. The spent fuel reprocessing operations ended in 1972 and DoE's cleanup operations have been underway since 1982. High-level waste solidification was safely concluded in 2002 and follow-on activities at the site have been concentrated on facility decontamination and waste management and off-site disposal. Among the features that remain at the WVDP site is the highly-contaminated Main Plant Process Building (MPPB). The five-story reinforced concrete structure, which was formerly used to reprocess irradiated nuclear fuel, contains residual levels of contamination in some areas that prohibit safe human entry. DoE's long-range plans for the site include demolition of the MPPB. Current site contractor, West Valley Environmental Services LLC (WVES), while actively working to dismantle equipment and decontaminate areas inside the MPPB, has developed a conceptual two-phase plan for demolishing the structure that provides a cost-effective, lower-dose alternative to conventional demolition techniques. This paper discusses the current condition of the MPPB and the demolition-ready preparations conducted in the facility thus far. This paper also introduces the concept of a two-part surgical demolition plan that has been proposed and is being evaluated as a safe method of demolishing the structure. The practical applications that support feasibility for the demolition approach are being demonstrated through current work applications in the MPPB. The Inside-Out Demolition proposal for the MPPB is a safe

Application of micro blasting technique to demolition of biological shield wall of reactor building

International Nuclear Information System (INIS)

Kontani, Osamu

2016-01-01

Although heavily reinforced concrete structures in nuclear facilities could be dismantled effectively with the controlled blasting technique, the noises and vibrations caused by blasting were matters of concern. Recently, in the building replacement at urban areas, there are increasing cases of demolition of large reinforced concrete members below ground. Instead of applying heavy weight breakers, the micro blasting technique that enables to lower noises and vibrations has developed and applied to demolition work of large reinforced concrete members in urban areas. In this report, the features of the micro blasting technique is reviewed by comparing with existing controlled blasting technique and its applicability to demolition work of nuclear facilities is investigated. The results of those study find that it is confirmed that the micro blasting technique could be applicable to large reinforced concrete structures in nuclear facilities because of the low levels of noises and vibrations. However, it is recommended to perform mock-up tests to confirm the demolition efficiency and levels of the noises and vibrations since the rebar used in nuclear facilities is larger in diameters and in rebar ratio compared with ordinary reinforced concrete structures. (author)

Distribution of materials in construction and demolition waste in Portugal.

Science.gov (United States)

Coelho, André; de Brito, Jorge

2011-08-01

It may not be enough simply to know the global volume of construction and demolition waste (CDW) generated in a certain region or country if one wants to estimate, for instance, the revenue accruing from separating several types of materials from the input entering a given CDW recycling plant. A more detailed determination of the distribution of the materials within the generated CDW is needed and the present paper addresses this issue, distinguishing different buildings and types of operation (new construction, retrofitting and demolition). This has been achieved by measuring the materials from buildings of different ages within the Portuguese building stock, and by using direct data from demolition/retrofitting sites and new construction average values reported in the literature. An attempt to establish a benchmark with other countries is also presented. This knowledge may also benefit industry management, especially that related to CDW recycling, helping to optimize procedures, equipment size and operation and even industrial plant spatial distribution. In an extremely competitive market, where as in Portugal low-tech and high environmental impact procedures remain the norm in the construction industry (in particular, the construction waste industry), the introduction of a successful recycling industry is only possible with highly optimized processes and based on a knowledge-based approach to problems.

A two-stage extraction procedure for insensitive munition (IM) explosive compounds in soils.

Science.gov (United States)

Felt, Deborah; Gurtowski, Luke; Nestler, Catherine C; Johnson, Jared; Larson, Steven

2016-12-01

The Department of Defense (DoD) is developing a new category of insensitive munitions (IMs) that are more resistant to detonation or promulgation from external stimuli than traditional munition formulations. The new explosive constituent compounds are 2,4-dinitroanisole (DNAN), nitroguanidine (NQ), and nitrotriazolone (NTO). The production and use of IM formulations may result in interaction of IM component compounds with soil. The chemical properties of these IM compounds present unique challenges for extraction from environmental matrices such as soil. A two-stage extraction procedure was developed and tested using several soil types amended with known concentrations of IM compounds. This procedure incorporates both an acidified phase and an organic phase to account for the chemical properties of the IM compounds. The method detection limits (MDLs) for all IM compounds in all soil types were regulatory risk-based Regional Screening Level (RSL) criteria for soil proposed by the U.S. Army Public Health Center. At defined environmentally relevant concentrations, the average recovery of each IM compound in each soil type was consistent and greater than 85%. The two-stage extraction method decreased the influence of soil composition on IM compound recovery. UV analysis of NTO established an isosbestic point based on varied pH at a detection wavelength of 341 nm. The two-stage soil extraction method is equally effective for traditional munition compounds, a potentially important point when examining soils exposed to both traditional and insensitive munitions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Strategy of Construction and Demolition Waste Management after Chemical Industry Facilities Removal

Science.gov (United States)

Tashkinova, I. N.; Batrakova, G. M.; Vaisman, Ya I.

2017-06-01

Mixed waste products are generated in the process of irrelevant industrial projects’ removal if conventional techniques of their demolition and dismantling are applied. In Russia the number of unused chemical industry facilities including structures with high rate of wear is growing. In removing industrial buildings and production shops it is used conventional techniques of demolition and dismantling in the process of which mixed waste products are generated. The presence of hazardous chemicals in these wastes makes difficulties for their use and leads to the increasing volume of unutilized residues. In the process of chemical industry facilities’ removal this fact takes on special significance as a high level of hazardous chemicals in the waste composition demands for the realization of unprofitable measures aimed at ensuring environmental and industrial safety. The proposed strategy of managing waste originated from the demolition and dismantling of chemical industry facilities is based on the methodology of industrial metabolism which allows identifying separate material flows of recycled, harmful and ballast components, performing separate collection of components during removal and taking necessary preventive measures. This strategy has been tested on the aniline synthesis plant being in the process of removal. As a result, a flow of 10 wt. %, subjected to decontamination, was isolated from the total volume of construction and demolition waste (C&D waste). The considered approach allowed using the resource potential of more than 80wt. % of waste and minimizing the disposed waste volume.

Construction and demolition waste generation rates for high-rise buildings in Malaysia.

Science.gov (United States)

Mah, Chooi Mei; Fujiwara, Takeshi; Ho, Chin Siong

2016-12-01

Construction and demolition waste continues to sharply increase in step with the economic growth of less developed countries. Though the construction industry is large, it is composed of small firms with individual waste management practices, often leading to the deleterious environmental outcomes. Quantifying construction and demolition waste generation allows policy makers and stakeholders to understand the true internal and external costs of construction, providing a necessary foundation for waste management planning that may overcome deleterious environmental outcomes and may be both economically and environmentally optimal. This study offers a theoretical method for estimating the construction and demolition project waste generation rate by utilising available data, including waste disposal truck size and number, and waste volume and composition. This method is proposed as a less burdensome and more broadly applicable alternative, in contrast to waste estimation by on-site hand sorting and weighing. The developed method is applied to 11 projects across Malaysia as the case study. This study quantifies waste generation rate and illustrates the construction method in influencing the waste generation rate, estimating that the conventional construction method has a waste generation rate of 9.88 t 100 m -2 , the mixed-construction method has a waste generation rate of 3.29 t 100 m -2 , and demolition projects have a waste generation rate of 104.28 t 100 m -2 . © The Author(s) 2016.

20000G shock energy harvesters for gun-fired munition

International Nuclear Information System (INIS)

Willemin, J.; Boisseau, S.; Olmos, L.; Gallardo, M.; Despesse, G.; Robert, T.

2016-01-01

This paper presents a 20000G shock energy harvester dedicated to gun-fired munitions and based on a mass-spring resonant structure coupled to a coil-magnet electromagnetic converter. The 20000G shock energy is firstly stored in the spring as elastic potential energy, released as mass-spring mechanical oscillations right after the shock and finally converted into electricity thanks to the coil-magnet transducer. The device has been modeled, sized to generate 200mJ in 150ms, manufactured and tested in a gun-fired munition. The prototype sizes 117cm 3 and weighs 370g. 210mJ have been generated in a test bench and 140mJ in real conditions; this corresponds to a mean output power of 0.93W (7.9mW/cm 3 ) and a maximum output power of 4.83W (41.3mW/cm 3 ) right after the shock. (paper)

20000G shock energy harvesters for gun-fired munition

Science.gov (United States)

Willemin, J.; Boisseau, S.; Olmos, L.; Gallardo, M.; Despesse, G.; Robert, T.

2016-11-01

This paper presents a 20000G shock energy harvester dedicated to gun-fired munitions and based on a mass-spring resonant structure coupled to a coil-magnet electromagnetic converter. The 20000G shock energy is firstly stored in the spring as elastic potential energy, released as mass-spring mechanical oscillations right after the shock and finally converted into electricity thanks to the coil-magnet transducer. The device has been modeled, sized to generate 200mJ in 150ms, manufactured and tested in a gun-fired munition. The prototype sizes 117cm3 and weighs 370g. 210mJ have been generated in a test bench and 140mJ in real conditions; this corresponds to a mean output power of 0.93W (7.9mW/cm3) and a maximum output power of 4.83W (41.3mW/cm3) right after the shock.

Construction, Maintenance and Demolition of Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Smet, Camiel de [Hilti Corporation, P.O. Box 333, FL-9494 Schaan (Liechtenstein)

2008-07-01

Hilti is your reliable partner in nuclear power plant construction, maintenance and demolition worldwide. Professional advice and innovative solutions for virtually every phase of construction and supply technologically leading products and systems to increase your productivity and help to create and maintain safe and lasting plants is offered. The solutions for nuclear power plants construction, maintenance and demolition have been employed with great success in many different countries on a wide variety of projects due in no small way to their worldwide availability. An unbroken, international exchange of experience upholds a permanent innovation process. This assures our customers that they always receive products on the very latest technological standard. This paper is not intended to cover all topics related to nuclear power plants. The idea is more to give a kind of an overview. The paper covers briefly the following topics: safety (corrosion and fire), fastenings, measuring and finally decommissioning of nuclear power plants. (author)

Towards a more professional demolition and dismantling industry

International Nuclear Information System (INIS)

1988-01-01

The work of the National Economic Development Office Demolition and Dismantling Group in four areas which are crucial to the economic performance of the demolition and dismantling industry and its safety record is considered. The first concerns the availability and accessibility of information about unconventional structures and details are given of the sort of information often kept for different types of structure. Secondly, the need is stressed for guidelines for the client, particularly on the risks involved and the choice of a competent contractor. Thirdly, basic credentials which it is important for contractors to set out in order to establish a good reputation for the industry are set out. Finally, the particular case of nuclear power station decommissioning is considered with reference to the size of the market, the pioneering knowledge to be gained from the decommissioning of the Windscale Advanced Gas-cooled Reactor, private sector involvement and the special techniques required. (U.K.)

Construction, Maintenance and Demolition of Nuclear Power Plants

International Nuclear Information System (INIS)

Smet, Camiel de

2008-01-01

Hilti is your reliable partner in nuclear power plant construction, maintenance and demolition worldwide. Professional advice and innovative solutions for virtually every phase of construction and supply technologically leading products and systems to increase your productivity and help to create and maintain safe and lasting plants is offered. The solutions for nuclear power plants construction, maintenance and demolition have been employed with great success in many different countries on a wide variety of projects due in no small way to their worldwide availability. An unbroken, international exchange of experience upholds a permanent innovation process. This assures our customers that they always receive products on the very latest technological standard. This paper is not intended to cover all topics related to nuclear power plants. The idea is more to give a kind of an overview. The paper covers briefly the following topics: safety (corrosion and fire), fastenings, measuring and finally decommissioning of nuclear power plants. (author)

48 CFR 252.225-7007 - Prohibition on Acquisition of United States Munitions List Items from Communist Chinese Military...

Science.gov (United States)

2010-10-01

... of United States Munitions List Items from Communist Chinese Military Companies. 252.225-7007 Section... Chinese Military Companies. As prescribed in 225.1103(4), use the following clause: Prohibition On Acquisition of United States Munitions List Items From Communist Chinese Military Companies (SEP 2006) (a...

A BIM-based system for demolition and renovation waste estimation and planning.

Science.gov (United States)

Cheng, Jack C P; Ma, Lauren Y H

2013-06-01

Due to the rising worldwide awareness of green environment, both government and contractors have to consider effective construction and demolition (C&D) waste management practices. The last two decades have witnessed the growing importance of demolition and renovation (D&R) works and the growing amount of D&R waste disposed to landfills every day, especially in developed cities like Hong Kong. Quantitative waste prediction is crucial for waste management. It can enable contractors to pinpoint critical waste generation processes and to plan waste control strategies. In addition, waste estimation could also facilitate some government waste management policies, such as the waste disposal charging scheme in Hong Kong. Currently, tools that can accurately and conveniently estimate the amount of waste from construction, renovation, and demolition projects are lacking. In the light of this research gap, this paper presents a building information modeling (BIM) based system that we have developed for estimation and planning of D&R waste. BIM allows multi-disciplinary information to be superimposed within one digital building model. Our system can extract material and volume information through the BIM model and integrate the information for detailed waste estimation and planning. Waste recycling and reuse are also considered in our system. Extracted material information can be provided to recyclers before demolition or renovation to make recycling stage more cooperative and more efficient. Pick-up truck requirements and waste disposal charging fee for different waste facilities will also be predicted through our system. The results could provide alerts to contractors ahead of time at project planning stage. This paper also presents an example scenario with a 47-floor residential building in Hong Kong to demonstrate our D&R waste estimation and planning system. As the BIM technology has been increasingly adopted in the architectural, engineering and construction industry

Use of demolition residues construction in soil-lime bricks

International Nuclear Information System (INIS)

Figueiredo, S.S.; Silva, C.G.; Silva, I.A.; Neves, G.A.

2011-01-01

Besides being responsible for several environmental damage caused by its residues, the construction industry is also considered the greatest natural resources consumer. When finely ground, such residues can exhibit cementing properties, which may replace part of the lime used in the manufacture of soil-lime bricks. This study aimed to verify the viability of using demolition residues (DR) in soil-lime bricks without structural function. For this, test specimens were prepared using mixes in a 1:10 ratio of lime:soil and embedding residue in partial replacement of lime in the proportions of 25%, 50% and 75%. The test specimens were submitted to curing periods of 28 and 52 days, then it was determined the compression strength. The results showed that when embedded on moderate percentages, demolition residues construction can be used in the production of soil-lime bricks. (author)

Health and environmental problems of using antiarmour munitions containing depleted uranium core

International Nuclear Information System (INIS)

Matousek, J.

2006-01-01

In the 1970s, core of depleted uranium commenced to be introduced into the breakthrough antitank munitions of various calibers and types in order to considerably enhance their effectiveness due to extremely high density in comparison with steel. The health and environmental threats of using this munitions and other weaponry where depleted uranium has been utilised as counterbalance stem from the pyrophoric character of uranium, burnt due to material deformation and friction when penetrating armour targets creating thus highly respirable aerosol of uranium oxides that are deposited in alveoli after being inhaled or in other tissues after being ingested. Composition and main properties of depleted uranium are presented. Chronic effects of deposited particles of uranium oxides are due to internal irradiation of sensitive organs at proceeding radioactive decay accompanied with alpha irradiation. Long-term internal irradiation by radionuclides producing alpha-rays leads to proved risk of increased incidence of carcinoma and leukaemia not to speak on chronic chemical toxicity of uranium, independent of its isotopic composition. Environmental impact of extensive use of munitions with depleted uranium in the recent armed conflicts is assessed. (authors)

Energy savings from housing: Ineffective renovation subsidies vs efficient demolition and reconstruction incentives

International Nuclear Information System (INIS)

Dubois, Maarten; Allacker, Karen

2015-01-01

Energy savings in the housing sector are key to reduce global greenhouse gas emissions. Policies to incentivize energy savings are however disparate between countries. Taking into account environmental aspects and consumer surplus, the paper uses a stylized economic model to assess the effectiveness and efficiency of three economic instruments: subsidies for renovation, subsidies for demolition and reconstruction projects and subsidies for building new houses on virgin land. The assessment also relates to differentiated value added taxes and other financial incentives such as green loans. In a counter-intuitive way, the model highlights that subsidies for renovations with minor energy gains worsen the overall energy consumption of housing due to the inducement of lock-ins with energy inefficient houses. Structural changes are needed in the use of policy instruments. First, commonly applied support schemes for renovations with minor energy savings should be abolished. Second, scarce public resources should incentivize deep renovation and demolition and reconstruction. Finally, taxes should apply on the use of virgin land to persuade households with a high willingness to pay for a new house, to invest in demolition and reconstruction. - Highlights: • Renovation subsidies worsen overall energy consumption of housing. • Renovation induces a lock-in with energy inefficient houses. • Renovation subsidies should be abolished or structurally reformed. • Policy should incentivize demolition and reconstruction projects. • Building on virgin land should be taxed.

Ambivalence in Place Attachment : The Lived Experiences of Residents in Declining Neighbourhoods Facing Demolition in Shenyang, China

NARCIS (Netherlands)

Li, X.; Kleinhans, R.J.; van Ham, M.

This paper investigates the place attachment of residents in declining neighbourhoods that are facing demolition in Shenyang, China. Through in-depth interviews with homeowners living in danwei communities, or urban villages, at the pre-demolition phase, this paper reveals the strong connection

Postwar City: Importance of Recycling Construction and Demolition Waste

Science.gov (United States)

Al-Qaraghuli, Hanan; Alsayed, Yaman; Almoghazy, Ali

2017-10-01

Wars and armed conflicts have heavy tolls on the built environment when they take place in cities. It is not only restricted to the actually fighting which destroys or damages buildings and infrastructure, but the damage and destruction inflicts its impacts way beyond the cessation of military actions. They can even have another impact through physical segregation of city quarters through walls and checkpoints that complicates, or even terminates, mobility of citizens, goods, and services in the post-war scenario. The accumulation of debris in the streets often impedes the processes of rescue, distribution of aid and services, and other forms of city life as well. Also, the amount of effort and energy needed to remove those residual materials to their final dumping sites divert a lot of urgently needed resources. In this paper, the components of construction and demolition waste found in post-war cities are to be discussed, relating each one to its origins and potential reuses. Then the issues related to the management of construction waste and demolition debris resulting from military actions are to be discussed. First, an outlook is to be given on the historical example of Berlin and how the city was severely damaged during World War II, and how the reconstruction of the city was aided in part by the reuse of demolition debris. Then two more recent examples will be given, the cities of Baghdad in Iraq, and Homs in Syria. In Baghdad, though major military actions have ceased but not all rubble is cleared out, some security structures in the form of concrete walls separate the cities into quarters and impede city life and lie around as poorly allocated resource needed for reconstruction. While in the case of Homs, and the wider Syrian context, major military operations are still raging, making more pressure on the resources needed for reconstruction. This recycling of demolition debris can bring economic and social stability through the conservation of resources

48 CFR 52.249-3 - Termination for Convenience of the Government (Dismantling, Demolition, or Removal of Improvements).

Science.gov (United States)

2010-10-01

... Convenience of the Government (Dismantling, Demolition, or Removal of Improvements). 52.249-3 Section 52.249-3... Convenience of the Government (Dismantling, Demolition, or Removal of Improvements). As prescribed in 49.502(b)(2), insert the following clause: Termination for Convenience of the Government (Dismantling...

Disposal of chemical agents and munitions stored at Pine Bluff Arsenal, Pine Bluff, Arkansas

Energy Technology Data Exchange (ETDEWEB)

Ensminger, J.T.; Hillsman, E.L.; Johnson, R.D.; Morrisey, J.A.; Staub, W.P.; Boston, C.R.; Hunsaker, D.B.; Leibsch, E.; Rickert, L.W.; Tolbert, V.R.; Zimmerman, G.P.

1991-09-01

The Pine Bluff Arsenal (PBA) near Pine Bluff, Arkansas, is one of eight continental United States (CONUS) Army installations where lethal unitary chemical agents and munitions are stored and where destruction of agents and munitions is proposed under the Chemical Stockpile Disposal Program (CSDP). The chemical agent inventory at PBA consists of approximately 12%, by weight, of the total US stockpile. The destruction of the stockpile is necessary to eliminate the risk to the public from continued storage and to dispose of obsolete and leaking munitions. In 1988 the US Army issued a Final Programmatic Environmental Impact Statement (FPEIS) for the CSDP that identified on-site disposal of agents and munitions as the environmentally preferred alternative (i.e., the alternative with the least potential to cause significant adverse impacts). The purpose of this report is to examine the proposed implementation of on-site disposal at PBA in light of more recent and more detailed data than those on which the FPEIS is based. New population data were used to compute fatalities using the same computation methods and values for all other parameters as in the FPEIS. Results indicate that all alternatives are indistinguishable when the potential health impacts to the PBA community are considered. However, risks from on-site disposal are in all cases equal to or less than risks from other alternatives. Furthermore, no unique resources with the potential to prevent or delay implementation of on-site disposal at PBA have been identified.

Generation of Exotic Quantum States of a Cold Atomic Ensemble

DEFF Research Database (Denmark)

Christensen, Stefan Lund

Over the last decades quantum effects have become more and more controllable, leading to the implementations of various quantum information protocols. These protocols are all based on utilizing quantum correlation. In this thesis we consider how states of an atomic ensemble with such correlations...... can be created and characterized. First we consider a spin-squeezed state. This state is generated by performing quantum non-demolition measurements of the atomic population difference. We show a spectroscopically relevant noise reduction of -1.7dB, the ensemble is in a many-body entangled state...... — a nanofiber based light-atom interface. Using a dual-frequency probing method we measure and prepare an ensemble with a sub-Poissonian atom number distribution. This is a first step towards the implementation of more exotic quantum states....

HAZWOPER project documents for demolition of the Waste Evaporator Facility, Building 3506, at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

1996-03-01

This document, in support of the Waste Evaporator Facility (WEF) demolition project and contains the Project Work Plan and the Project Health and Safety Plan for demolition and partial remediation actions by ATG at the Waste Evaporator Facility, Building 3506. Various activities will be conducted during the course of demolition, and this plan provides details on the work steps involved, the identification of hazards, and the health and safety practices necessary to mitigate these hazards. The objective of this document is to develop an approach for implementing demolition activities at the WEF. This approach is based on prior site characterization information and takes into account all of the known hazards at this facility. The Project Work Plan provides instructions and requirements for identified work steps that will be utilized during the performance of demolition, while the Health and Safety Plan addresses the radiological, hazardous material exposure, and industrial safety concerns that will be encountered

HAZWOPER project documents for demolition of the Waste Evaporator Facility, Building 3506, at Oak Ridge National Laboratory, Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

This document, in support of the Waste Evaporator Facility (WEF) demolition project and contains the Project Work Plan and the Project Health and Safety Plan for demolition and partial remediation actions by ATG at the Waste Evaporator Facility, Building 3506. Various activities will be conducted during the course of demolition, and this plan provides details on the work steps involved, the identification of hazards, and the health and safety practices necessary to mitigate these hazards. The objective of this document is to develop an approach for implementing demolition activities at the WEF. This approach is based on prior site characterization information and takes into account all of the known hazards at this facility. The Project Work Plan provides instructions and requirements for identified work steps that will be utilized during the performance of demolition, while the Health and Safety Plan addresses the radiological, hazardous material exposure, and industrial safety concerns that will be encountered.

Demolition of Building 12, an old plutonium filter facility

International Nuclear Information System (INIS)

Christensen, E.L.; Garde, R.; Valentine, A.M.

1975-01-01

This report discusses the decommissioning and disposal of a plutonium-contaminated air filter facility that provided ventilation for the main plutonium processing plant at Los Alamos from 1945 until 1973. The health physics, waste management, and environmental aspects of the demolition are also discussed

Modeling end-of-life pathways of construction and demolition debris in the United States (poster for LCM 2017)

Science.gov (United States)

In 2013, the United States generated 530 million tons of construction and demolition debris (CDD), 90% of which was related to demolition. Despite this major contribution to national waste streams, Life Cycle Assessment (LCA) studies and product declarations of buildings and buil...

Y-12 Construction/Demolition Landfill VII: Permit application: Part 1 and 2

International Nuclear Information System (INIS)

1992-04-01

The United States Department of Energy (DOE) has three major operating facilities on the DOE Oak Ridge Reservation (ORR) at Oak Ridge, Tennessee: the Y-12 Plant, the K-25 Site, and the Oak Ridge National Laboratory (ORNL). Operations associated with the DOE energy research and production facilities at Oak Ridge result in the production of several types of waste materials. Disposal of solid waste (as defined in the Solid Waste Processing and Disposal Rules for Tennessee) in disposal facilities operated by the Y-12 Plant is the responsibility of Y-12 Waste Management Division (MWD). The WMD is proposing to develop a facility that will include two new disposal units: one for construction/demolition waste and spoil and one for industrial solid waste. This manual describes the closure and post-closure plans for the construction/demolition waste and spoil disposal unit. This disposal unit is referred to as the Y-12 Construction/Demolition Landfill VII (CD-VII) and is to be operated by the Y-12 Plant for the DOE. This will be a Tennessee Department of Environment and Conservation/Division of Solid Waste Management (TDEC/DSWM) Class IV disposal unit

Quantum demolition filtering and optimal control of unstable systems.

Science.gov (United States)

Belavkin, V P

2012-11-28

A brief account of the quantum information dynamics and dynamical programming methods for optimal control of quantum unstable systems is given to both open loop and feedback control schemes corresponding respectively to deterministic and stochastic semi-Markov dynamics of stable or unstable systems. For the quantum feedback control scheme, we exploit the separation theorem of filtering and control aspects as in the usual case of quantum stable systems with non-demolition observation. This allows us to start with the Belavkin quantum filtering equation generalized to demolition observations and derive the generalized Hamilton-Jacobi-Bellman equation using standard arguments of classical control theory. This is equivalent to a Hamilton-Jacobi equation with an extra linear dissipative term if the control is restricted to Hamiltonian terms in the filtering equation. An unstable controlled qubit is considered as an example throughout the development of the formalism. Finally, we discuss optimum observation strategies to obtain a pure quantum qubit state from a mixed one.

Investigation of a new passive sampler for the detection of munitions compounds in marine and freshwater systems.

Science.gov (United States)

Warren, Joseph K; Vlahos, Penny; Smith, Richard; Tobias, Craig

2018-07-01

Over the last century, unexploded ordnances have been disposed of in marine shelf systems because of a lack of cost-effective alternatives. Underwater unexploded ordnances have the potential to leak 2,4,6-trinitrotoluene (TNT) and 1,3,5-trinitro-1,3,5-triazine (RDX), commonly used chemical munitions, and contaminate local waters, biota, and sediments. The rate at which this contamination occurs in the environment is relatively unknown, and the cost- and time-prohibitive nature of sampling across sites makes mapping difficult. In the present study we assessed the efficacy of ethylene-vinyl acetate (EVA) for sampling relatively soluble munitions compounds over a range of environmental conditions (i.e., changes in temperature and salinity) and optimized the composition of the passive sampling polymer. The EVA sampler was able to successfully detect ambient concentrations of lingering munitions compounds from field sites containing unexploded ordnances. The sampler affinity for the munitions in terms of an EVA-water partition coefficient was greater than the standard octanol water values for each target compound. Partitioning of compounds onto EVA over the natural ranges of salinity did not change significantly, although uptake varied consistently and predictably with temperature. Increasing the vinyl acetate to ethylene ratio of the polymer corresponded to an increase in uptake capacity, consistent with enhanced dipole-dipole interactions between the munitions and the polymer. This sampler provides a cost-effective means to map and track leakage of unexploded ordnances both spatially and temporally. Environ Toxicol Chem 2018;37:1990-1997. © 2018 SETAC. © 2018 SETAC.

Modified Brokk Demolition Machine with Remote Operator Console. Innovative Technology Summary Report

International Nuclear Information System (INIS)

2001-01-01

The Low-Cost D and D System modifies a commercially available BROKK demolition system for remote viewing and long tether remote operation that provides a portable facility camera pod and interfaces with the Compact Remote Operator Console (TMS Tech ID 2180) to extend the applicability of the BROKK system to projects that require removal of the operator from the work area due to exposure to radiological, chemical, or industrial hazards. The modified BROKK has been integrated with the Compact Remote Operator Console to provide a true remotely operated low-cost D and D system applicable to a wide range of small D and D demolition tasks across the DOE complex

Strategic Munitions Planning in Non-Conventional Asymmetric Operations

Science.gov (United States)

2010-04-01

Conventional Asymmetric Operations RTO-MP-SAS-081 16 - 3 with a clearly structured, sized and located military force. The principles of Lanchester ...stockpiles and calculated munitions requirements. REFERENCES [1] Prague Summit Declaration, November 2002. [2] J. Fletcher, The Lanchester Legacy... Lanchester battles, Journal of the Operational Research Society, Vol. 50 No. 3, March 1999. [13] W. Freeman, A Study of Ammunition Consumption, Master of

Underwater Munitions Expert System: Preliminary Design Report

Science.gov (United States)

2015-08-21

analysis  would  usually  be  performed,   where  separation  by   sieving  results  in  the  PMF  of  sand  grain...locations  they  might  potentially   aggregate .    Furthermore,  given  knowledge  of  the  types  of   munitions...feature  that   Netica  provides  is  the  ability  to  do  sensitivity   analysis ,

REMOTE SENSING IN DETECTING BURIED MUNITIONS FROM WORLD WAR I

Science.gov (United States)

During World War I, The American University in Washington D.C. was used by the U.S. Army as an experiment station for the development and testing of a variety of battlefield munitions including chemical weapons such as Mustard Gas, Phosgene, Ricin and Lewisite, among othe...

Disposal of chemical agents and munitions stored at Umatilla Depot Activity, Hermiston, Oregon

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, G.P.; Hillsman, E.L.; Johnson, R.O.; Miller, R.L.; Patton, T.G.; Schoepfle, G.M.; Tolbert, V.R.; Feldman, D.L.; Hunsaker, D.B. Jr.; Kroodsma, R.L.; Morrissey, J.; Rickert, L.W.; Staub, W.P.; West, D.C.

1993-02-01

The Umatilla Depot Activity (UMDA) near Hermiston, Oregon, is one of eight US Army installations in the continental United States where lethal unitary chemical agents and munitions are stored, and where destruction of agents and munitions is proposed under the Chemical Stockpile Disposal Program (CSDP). The chemical agent inventory at UMDA consists of 11.6%, by weight, of the total US stockpile. The destruction of the stockpile is necessary to eliminate the risk to the public from continued storage and to dispose of obsolete and leaking munitions. In 1988 the US Army issued a Final Programmatic Environmental Impact Statement (FPEIS) for the CSDP that identified on-site disposal of agents and munitions as the environmentally preferred alternative (i.e., the alternative with the least potential to cause significant adverse impacts), using a method based on five measures of risk for potential human health and ecosystem/environmental effects; the effectiveness and adequacy of emergency preparedness capabilities also played a key role in the FPEIS selection methodology. In some instances, the FPEIS included generic data and assumptions that were developed to allow a consistent comparison of potential impacts among programmatic alternatives and did not include detailed conditions at each of the eight installations. The purpose of this Phase 1 report is to examine the proposed implementation of on-site disposal at UMDA in light of more recent and more detailed data than those included in the FPEIS. Specifically, this Phase 1 report is intended to either confirm or reject the validity of on-site disposal for the UMDA stockpile. Using the same computation methods as in the FPEIS, new population data were used to compute potential fatalities from hypothetical disposal accidents. Results indicate that onsite disposal is clearly preferable to either continued storage at UMDA or transportation of the UMDA stockpile to another depot for disposal.

The Political Economy of the Munitions Supply Program

Science.gov (United States)

2014-05-01

advantage in production, and further identified which munitions products can be procured offshore with only limited effects on operational liabilities...comparative advantage and access to global supply chains. A few options exist: fixed-price contracts may be indexed to exogenously-given input prices and... franchisees bid their true costs.47 Third, once supply is forthcoming, the franchisee has an incentive to minimize costs unless the franchiser is known

Environmental Impacts Assessment of Recycling of Construction and Demolition Waste

DEFF Research Database (Denmark)

Butera, Stefania

.e. soil and stones, concrete, asphalt and masonry, and as such it has the potential to be used as aggregate in the construction sector. A typical application is in an unbound state as filler in road structures. This practice offers evident benefits in terms of resource savings, however it might lead......Construction and demolition waste (C&DW) is waste derived from the construction, demolition and renovation of buildings and civil infrastructure. With 900 million tons generated every year in Europe, it is the largest waste stream on the continent. C&DW is mainly constituted of mineral fractions, i...... be evaluated critically.Owing to its high toxicity and significant mobility, especially at high pH levels, Cr(VI) is one of the elements of concern found in C&DW leachates. Its fate in the sub-soil below road applications was assessed experimentally, and its vertical migration was then predicted through...

Does demolition or refurbishment of old and inefficient homes help to increase our environmental, social and economic viability?

Energy Technology Data Exchange (ETDEWEB)

Power, Anne [London School of Economics, Houghton Street, London WC2A 2AE (United Kingdom); Sustainable Development Commission, Room 101, 55 Whitehall, c/o 3-8 Whitehall Place, London SW1A 2HH (United Kingdom)

2008-12-15

The issue of whether to demolish or refurbish older housing has been debated for over a century. It has been an active policy area since the late 1880s, when the Government first authorised the statutory demolition of insanitary slums. In the 1960s, revulsion at the scale of 'demolition blight' and new building caused a rethink, leading to a major reinvestment in inner city neighbourhoods of older housing. In the past 5 years, debate on demolition and new building has been intensified by the Government's Sustainable Communities Plan of 2003, with its proposals for large-scale clearance and building. Environmental arguments about renovating the existing stock have gained increasing prominence as people have sought to defend their communities from demolition. The evidence on whether demolition would reduce the amount of greenhouse gases we emit into the atmosphere is unclear and disputed. This paper summarises the evidence and arguments, and attempts to clarify the most realistic, achievable route to major reductions in energy use in homes. The arguments that apply to housing also apply to most other buildings and therefore to the overall built environment, which accounts for half of all carbon emissions. Three main sources of evidence have helped in the development of this paper, but there are many other studies we draw on in the discussion.

A BIM-based system for demolition and renovation waste estimation and planning

International Nuclear Information System (INIS)

Cheng, Jack C.P.; Ma, Lauren Y.H.

2013-01-01

Highlights: ► We developed a waste estimation system leveraging the BIM technology. ► The system can calculate waste disposal charging fee and pick-up truck demand. ► We presented an example scenario demonstrating this system. ► Automatic, time-saving and wide applicability are the features of the system. - Abstract: Due to the rising worldwide awareness of green environment, both government and contractors have to consider effective construction and demolition (C and D) waste management practices. The last two decades have witnessed the growing importance of demolition and renovation (D and R) works and the growing amount of D and R waste disposed to landfills every day, especially in developed cities like Hong Kong. Quantitative waste prediction is crucial for waste management. It can enable contractors to pinpoint critical waste generation processes and to plan waste control strategies. In addition, waste estimation could also facilitate some government waste management policies, such as the waste disposal charging scheme in Hong Kong. Currently, tools that can accurately and conveniently estimate the amount of waste from construction, renovation, and demolition projects are lacking. In the light of this research gap, this paper presents a building information modeling (BIM) based system that we have developed for estimation and planning of D and R waste. BIM allows multi-disciplinary information to be superimposed within one digital building model. Our system can extract material and volume information through the BIM model and integrate the information for detailed waste estimation and planning. Waste recycling and reuse are also considered in our system. Extracted material information can be provided to recyclers before demolition or renovation to make recycling stage more cooperative and more efficient. Pick-up truck requirements and waste disposal charging fee for different waste facilities will also be predicted through our system. The results

A BIM-based system for demolition and renovation waste estimation and planning

Energy Technology Data Exchange (ETDEWEB)

Cheng, Jack C.P., E-mail: cejcheng@ust.hk [Department of Civil and Environmental Engineering, The Hong Kong University of Science and Technology (Hong Kong); Ma, Lauren Y.H., E-mail: yingzi@ust.hk [Department of Civil and Environmental Engineering, The Hong Kong University of Science and Technology (Hong Kong)

2013-06-15

Highlights: ► We developed a waste estimation system leveraging the BIM technology. ► The system can calculate waste disposal charging fee and pick-up truck demand. ► We presented an example scenario demonstrating this system. ► Automatic, time-saving and wide applicability are the features of the system. - Abstract: Due to the rising worldwide awareness of green environment, both government and contractors have to consider effective construction and demolition (C and D) waste management practices. The last two decades have witnessed the growing importance of demolition and renovation (D and R) works and the growing amount of D and R waste disposed to landfills every day, especially in developed cities like Hong Kong. Quantitative waste prediction is crucial for waste management. It can enable contractors to pinpoint critical waste generation processes and to plan waste control strategies. In addition, waste estimation could also facilitate some government waste management policies, such as the waste disposal charging scheme in Hong Kong. Currently, tools that can accurately and conveniently estimate the amount of waste from construction, renovation, and demolition projects are lacking. In the light of this research gap, this paper presents a building information modeling (BIM) based system that we have developed for estimation and planning of D and R waste. BIM allows multi-disciplinary information to be superimposed within one digital building model. Our system can extract material and volume information through the BIM model and integrate the information for detailed waste estimation and planning. Waste recycling and reuse are also considered in our system. Extracted material information can be provided to recyclers before demolition or renovation to make recycling stage more cooperative and more efficient. Pick-up truck requirements and waste disposal charging fee for different waste facilities will also be predicted through our system. The results

Munitions having an insensitive detonator system for initiating large failure diameter explosives

Science.gov (United States)

Perry, III, William Leroy

2015-08-04

A munition according to a preferred embodiment can include a detonator system having a detonator that is selectively coupled to a microwave source that functions to selectively prime, activate, initiate, and/or sensitize an insensitive explosive material for detonation. The preferred detonator can include an explosive cavity having a barrier within which an insensitive explosive material is disposed and a waveguide coupled to the explosive cavity. The preferred system can further include a microwave source coupled to the waveguide such that microwaves enter the explosive cavity and impinge on the insensitive explosive material to sensitize the explosive material for detonation. In use the preferred embodiments permit the deployment and use of munitions that are maintained in an insensitive state until the actual time of use, thereby substantially preventing unauthorized or unintended detonation thereof.

Influence of construction and demolition waste management on the environmental impact of buildings.

Science.gov (United States)

Coelho, André; de Brito, Jorge

2012-03-01

The purpose of this study is to quantify comparable environmental impacts within a Life Cycle Analysis (LCA) perspective, for buildings in which the first (Materials) and last (End of Life) life cycle stages are adjusted to several waste/material management options. Unlike most LCAs, the approach is "top-down" rather than "bottom-up", which usually involves large amounts of data and the use of specific software applications. This approach is considered appropriate for a limited but expedient LCA designed to compare the environmental impacts of different life cycle options. Present results, based on real buildings measurements and demolition contractor activities, show that shallow, superficial, selective demolition may not result in reduced environmental impacts. Calculations actually show an increase (generally less than 5%) in most impact categories for the Materials and End of Life stages because of extra transportation needs. However, core material separation in demolition operations and its recycling and/or reuse does bring environmental benefits. A reduction of around 77% has been estimated in the climate change impact category, 57% in acidification potential and 81% in the summer smog impact (for the life cycle stages referred). Copyright © 2011 Elsevier Ltd. All rights reserved.

Underwater Munitions Expert System to Predict Mobility and Burial

Science.gov (United States)

2017-11-14

for predicting the location and possible burial of underwater munitions is required to advise site managers as they plan...that region above the given UXO relative density, which is defined as the UXO density divided by the sand grain density, ( nominally 2650 g...0.0 + 2.5*dsed ; % nominal bed roughness if no burial % (Potentially in future version, ripple height

National Security Strategy and the Munitions' Paradox: Self-Sufficiency or Maximum Efficiency

National Research Council Canada - National Science Library

McChesney, Michael

1998-01-01

... that the United States military strategy may not be credible to likely regional aggressors. Conversely, DoD acquisition leadership believes industry consolidation should continue and the munitions base should be expanded to include US allies...

Concrete block production from construction and demolition waste in Tanzania

NARCIS (Netherlands)

Sabai, M.M.; Cox, M.G.D.M.; Mato, R.R.A.M.; Egmond - de Wilde De Ligny, van E.L.C.; Lichtenberg, J.J.N.

2013-01-01

In Tanzania, construction and demolition (C&D) waste is not recycled and knowledge on how it can be recycled especially into valuable products like building materials are still limited. This study aimed at investigating the possibility of recycling the C&D waste (mainly cementitious rubble) into

Progressing Insensitive Munitions: Benefits and Techniques for Proactively Addressing Environmental Regulations

Science.gov (United States)

2012-05-01

X Worm Tubifex tubifex X X X Black worm Lumbriculus X Asiatic clam Corbicula fluminea X Estuarine/marine water column Mysid shrimp Americamysis...Objective: Characterize traditional and insensitive munitions (IMs) impacts on amphibian larvae to manage a candidate for T&E status that inhabit

Creation and demolition of illegal structures in Nigerian cities ...

African Journals Online (AJOL)

The paper examined the issue of demolition of illegal structures in Benin City. The study revealed that the poor economic condition of the country forced many landlords in the city to restructure and convert their houses into mixed uses in order to make a living. In the process many illegal structures sprang up as many ...

Oxidation kinetics of the combustible fraction of construction and demolition wastes.

Science.gov (United States)

Chang, N B; Lin, K S; Sun, Y P; Wang, H P

2001-01-01

Proper disposal of construction and demolition wastes (CDW) has received wide attention recently due to significantly large quantities of waste streams collected from razed or retrofitted buildings in many metropolitan regions. Burning the combustible fractions of CDW (CCDW) and possibly recovering part of the heat content for economic uses could be valuable for energy conservation. This paper explores the oxidation kinetics of CCDW associated with its ash characterization. Kinetic parameters for the oxidation of CCDW were numerically calculated using thermal gravimetric analysis (TGA) and the resultant rate equations were therefore developed for illustrating the oxidation processes of CCDW simultaneously. Based on three designated heating rates, each of the oxidation processes can be featured distinctively with five different stages according to the rate of weight change at the temperature between 300 K and 923 K. In addition, Fourier transform infrared (FTIR) spectroscopy was employed, associated with a lab-scale fixed-bed incinerator for monitoring the composition of flue gas. Carbon dioxide (CO2) was found as a major component in the flue gas. The fuel analysis also included an ash composition analysis via the use of X-ray powder diffraction (XRD), atomic absorption (AA) spectroscopy, inductively coupled plasma-atomic emission spectroscopy (ICP-AES), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDX). The ash streams were identified as nonhazardous materials based on the toxicity characteristic leaching procedure (TCLP). Overall, the scientific findings gained in this study will be helpful for supporting a sound engineering design of real-world CCDW incineration systems.

Using waterjet in reverse logistic operations in discarded munitions processing

Czech Academy of Sciences Publication Activity Database

Hloch, S.; Tozan, H.; Yagimli, M.; Valíček, Jan; Rokosz, K.

2011-01-01

Roč. 18, č. 2 (2011), s. 267-271 ISSN 1330-3651 Institutional research plan: CEZ:AV0Z30860518 Keywords : abrasive waterjet * anti tank bullet * automatic line Subject RIV: JQ - Machines ; Tools Impact factor: 0.347, year: 2011 http://hrcak.srce.hr/search/?q=Using+waterjet+in+reverse+logistic+operations+in+discarded+munitions+processing

Use of rubble from building demolition in mortars.

Science.gov (United States)

Corinaldesi, V; Giuggiolini, M; Moriconi, G

2002-01-01

Because of increasing waste production and public concerns about the environment, it is desirable to recycle materials from building demolition. If suitably selected, ground, cleaned and sieved in appropriate industrial crushing plants, these materials can be profitably used in concrete. Nevertheless, the presence of masonry instead of concrete rubble is particularly detrimental to the mechanical performance and durability of recycled-aggregate concrete and the same negative effect is detectable when natural sand is replaced by fine recycled aggregate fraction. An alternative use of both masonry rubble and fine recycled material fraction could be in mortars. These could contain either recycled instead of natural sand or powder obtained by bricks crushing as partial cement substitution. In particular, attention is focused on the modification that takes place when either polypropylene or stainless steel fibers are added to these mortars. Polypropylene fibers are added in order to reduce shrinkage of mortars, stainless steel fibers for improving their flexural strength. The combined use of polypropylene fibers and fine recycled material from building demolition could allow the preparation of mortars showing good performance, in particular when coupled with bricks. Furthermore, the combined use of stainless steel fibers and mortars containing brick powder seems to be an effective way to guarantee a high flexural strength.

Innovative permeable cover system to reduce risks at a chemical munitions burial site

International Nuclear Information System (INIS)

Powels, C.C.; Bon, I.; Okusu, N.M.

1997-01-01

An innovative permeable sand cover with various integrated systems has been designed to contain and treat the Old O-Field chemical munitions landfill at Aberdeen Proving Ground, Maryland. The 18,200 m 2 (4.5 acre) landfill was used from the mid 1930s to the mid 1950s for the disposal of chemical, incendiary, and explosive munitions from domestic and foreign origins, together with contaminated wastes associated with the development and production of chemical warfare agents (CWA). The site is suspected to be contaminated with white phosphorous (WP) (which when dry, spontaneously burns when exposed to air), shock sensitive picric acid fuses and has the potential to contain large quantities of CWA-filled munitions. Historically, one to three explosions or fires occurred per ten-year period at the landfill. Such events have the potential to cause a CWA release to the environment, which could potentially affect densely populated areas. Recovery and decontamination projects conducted at the site in the late 1940s and early 1950s used large amounts of decontamination chemicals (containing solvents) and fuels which further contaminated the area. The groundwater downgradient of the landfill is contaminated with volatile organic compounds, metals, explosives and CWA degradation compounds and is currently being contained by a groundwater extraction and treatment system. This report describes a remedial action program for the site

Bat Surveys of Retired Facilitiies Scheduled for Demolition by Washington Closure Hanford

Energy Technology Data Exchange (ETDEWEB)

Gano, K. A.; Lucas, J. G.; Lindsey, C. T.

2011-06-30

This project was conducted to evaluate buildings and facilities remaining in the Washington Closure Hanford (WCH) deactivation, decontamination, decommissioning, and demolition schedule for bat roost sites. The project began in spring of 2009 and was concluded in spring of 2011. A total of 196 buildings and facilities were evaluated for the presence of bat roosting sites. The schedule for the project was prioritized to accommodate the demolition schedule. As the surveys were completed, the results were provided to the project managers to facilitate planning and project completion. The surveys took place in the 300 Area, 400 Area, 100-H, 100-D, 100-N, and 100-B/C Area. This report is the culmination of all the bat surveys and summarizes the findings by area and includes recommended mitigation actions where bat roosts were found.

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F.W.M. [EPON, Zwolle (Netherlands)

1997-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Coal and wood fuel for electricity production: An environmentally sound solution for waste and demolition wood

Energy Technology Data Exchange (ETDEWEB)

Penninks, F W.M. [EPON, Zwolle (Netherlands)

1998-12-31

Waste wood from primary wood processing and demolition presents both a problem and a potential. If disposed in landfills, it consumes large volumes and decays, producing CH{sub 4}, CO{sub 2} and other greenhouse gases. As an energy source used in a coal fired power plant it reduces the consumption of fossil fuels reducing the greenhouse effect significantly. Additional advantages are a reduction of the ash volume and the SO{sub 2} and NO{sub x} emissions. The waste wood requires collection, storage, processing and burning. This paper describes a unique project which is carried out in the Netherlands at EPON`s Gelderland Power Plant (635 MW{sub e}) where 60 000 tonnes of waste and demolition wood will be used annually. Special emphasis is given to the processing of the powdered wood fuel. Therefore, most waste and demolition wood can be converted from an environmental liability to an environmental and economic asset. (author)

Analysis of Biota to Evaluate the Risks Associated with Chemical Warfare Materiel Present in Sea-Disposed Military Munitions to Human Health and the Environment

Science.gov (United States)

Briggs, C. W.; Bissonnette, M. C.; Edwards, M.; Shjegstad, S. M.

2016-12-01

Thousands of 100-lb M47A series bombs containing sulfur mustard were disposed in the ocean following World War II yet few studies have been conducted at sites in excess of 250 m, the depth where most discarded military munitions (DMM) were disposed. The Hawai`i Undersea Military Munitions Assessment (HUMMA) project was conducted to evaluate the risk from chemical warfare materiel (CWM) in DMM to human health, measuring ecological differences between the disposal area and nearby but otherwise similar areas, and evaluating the most efficient platforms for surveying DMM sea-disposal sites located at depths between 400-650 m. During the 2014 HUMMA Sampling Survey, the Jason 2 remotely operated vehicle was used to collect data. Shrimp were collected and analyzed to assess the potential for bioaccumulation of CWM, energetics and metals from munitions. No CWM was detected in H. ensifer tissue samples, indicating bioaccumulation is not occurring. Low levels of 2,4,6-trinitrotoluene, 4-amino-2,6-­dinitrotoluene, 1,3,5-trinitrobenzene, nitrobenzene, arsenic, copper, and lead were detected and the concentrations were not significantly different at DMM and control sites. No visible deformities, eroded fins, lesions, or tumors were observed on the shrimp living in the vicinity of M47A bombs. Given these results and under current and potential future uses of the HUMMA study area, health risks to likely receptors are within EPA acceptable levels. Photographic data and benthic infauna analysis were used to study benthic organisms that lived on or near munitions. There was no statistically distinguishable difference between organism distributions in dense and sparse munitions fields. Conventional munitions were found to have the greatest number of benthic infauna individuals, with control sites generally having the least number of individuals. This is consistent with the benthic macro-fauna analysis, which shows that munitions provide habitat.

Fracture analysis of cement treated demolition waste using a lattice model

NARCIS (Netherlands)

Xuan, D.; Schlangen, H.E.J.G.; Molenaar, A.A.A.; Houben, L.J.M.

2013-01-01

Fracture properties of cement treated demolition waste were investigated using a lattice model. In practice the investigated material is applied as a cement treated road base/subbase course. The granular aggregates used in this material were crushed recycled concrete and masonry. This results in six

Measurements of sub photon cavity fields by atom interferometry; Mesures de champs au niveau du photon par interferometrie atomique

Energy Technology Data Exchange (ETDEWEB)

Nussenzveig, P

1994-07-15

Two neighbouring levels of a Rydberg atom coupled to a high quality-factor microwave cavity are an excellent tool for the study of matter-wave interactions at the most basic level. The system is so simple (a two-level atom coupled to a single mode of the field) that most phenomena can be described analytically. In this work we study dispersive effects of the non-resonant atom-cavity interaction. We have measured the linear dependence of the atomic energy level-shifts on the average photon number in the cavity. Light shifts induced by an average microwave field intensity weaker than a single photon have been observed. It has also been possible to measure the residual shift of one of the two levels of the atomic transition in the absence of an injected field: a Lamb shift due to a single mode of the field. A sensitive measurement of these energy shifts is performed by an interferometric method: the Ramsey separated oscillatory fields technique. Future experiments, in a situation of very weak field relaxation, are proposed. The quantum behavior of the field will then be dominant and it shall be possible to perform a Quantum Non-Demolition measurement of the photon number: since the interaction is non-resonant, the atoms can neither absorb nor emit photons in the cavity. The performed experiments demonstrate the sensitivity of the apparatus and set the stage for future non-demolition measurements and for the study of 'mesoscopic' Schroedinger cat states of the field, on the boundary between classical and quantum worlds. (author)

The decommissioning and demolition of four suites of high active chemical analysis cells at DNPDE

International Nuclear Information System (INIS)

Black, R.M.; Spence, B.W.; Stewart, C.W.

1987-11-01

The decommissioning and demolition of four laboratory suites of high active cells at DNPDE is described. All four suites had suffered drain leaks of high active liquor into underfloor ducts; the options available at the time and current policy for dealing with the resultant activity deposits are given. The decommissioning procedures are detailed to provide information for future similar exercises. Features to ease demolition of such facilities and to eliminate the possibility of long term activity deposition from drain leaks are highlighted for incorporation in future designs. The waste arisings and radiation doses received during the work are tabulated. (author)

Downcycling versus recycling of construction and demolition waste: Combining LCA and LCC to support sustainable policy making.

Science.gov (United States)

Di Maria, Andrea; Eyckmans, Johan; Van Acker, Karel

2018-05-01

Urgent solutions are needed in Europe to deal with construction and demolition waste (CDW). EU policy has contributed to significantly reducing the amount of CDW going to landfill, but most of the effort has been put in downcycling practices. Therefore, further policies are needed to stimulate high-quality recycling of CDW. The present paper presents a combined life cycle assessment (LCA) and life cycle costing (LCC) methodologies to analyse the environmental and the economic drivers in four alternative CDW end-of-life scenarios in the region of Flanders, in Belgium. The four analysed alternatives are (i) landfilling, (ii) downcycling, (iii) advanced recycling and (iv) recycling after selective demolition. LCA results show that landiflling is the scenario having the highest environmental impacts in terms of person equivalent (PE), followed by downcycling and recycling (-36%) and recycling after selective demolition (-59%). The decrease in environmental impacts is mostly due to the avoided landfilling of CDW and the recovery of materials from selective demolition. LCC results indicate that landfilling is the scenario bearing the highest total economic costs. This is due to the high landfill tax in Flanders. The recycling after selective demolition bears the second highest cost. The increase of high-quality CDW recycling can significantly reduce the overall environmental impact of the system. Implementing a high landfill tax, increasing the gate fee to the recycling plant, and boosting the sales price of recycled aggregates are the most effective drivers to facilitate a transition towards a more sustainable CDW management system. The paper demonstrates that the combined LCA and LCC results can highlight the environmental and economic drivers in CDW management. The results of the combined analysis can help policymakers to promote the aspects contributing to sustainability and to limit the ones creating a barrier. Copyright © 2018 Elsevier Ltd. All rights reserved.

Construction and Demolition Debris 2014 US Final Disposition Estimates Using the CDDPath Method

Data.gov (United States)

U.S. Environmental Protection Agency — Estimates of the final amount and final disposition of materials generated in the Construction and Demolition waste stream measured in total mass of each material....

An integrated approach for the management of demolition waste in Cyprus.

Science.gov (United States)

Kourmpanis, Basilis; Papadopoulos, Achilleas; Moustakas, Konstantinos; Kourmoussis, Fotis; Stylianou, Marinos; Loizidou, Maria

2008-12-01

This study investigated the generation and management of demolition waste (DW) in Cyprus. A methodology has been developed and applied for the estimation of the quantities of the waste stream under examination, since quantitative primary data were not available. The existing situation relating to the practices applied for the management of DW was investigated and assessed. Furthermore, a multi-criteria analysis method (PROMETHEE II) was developed and applied in order to examine alternative systems that could be implemented for the management of the DW in the country. In particular, nine management systems (scenarios) were examined, evaluated and ranked according to their efficiency using seventeen individual criteria, divided into four groups (social-legislative, environmental, economic and technical). The ranking of the alternative waste management scenarios indicated that the optimum management system for possible implementation in the island included complete selective demolition procedures and transfer of mixed recyclable materials to the recycling centre and non-recyclable material to landfill.

Depleted uranium instead of lead in munitions: the lesser evil.

Science.gov (United States)

Jargin, Sergei V

2014-03-01

Uranium has many similarities to lead in its exposure mechanisms, metabolism and target organs. However, lead is more toxic, which is reflected in the threshold limit values. The main potential hazard associated with depleted uranium is inhalation of the aerosols created when a projectile hits an armoured target. A person can be exposed to lead in similar ways. Accidental dangerous exposures can result from contact with both substances. Encountering uranium fragments is of minor significance because of the low penetration depth of alpha particles emitted by uranium: they are unable to penetrate even the superficial keratin layer of human skin. An additional cancer risk attributable to the uranium exposure might be significant only in case of prolonged contact of the contaminant with susceptible tissues. Lead intoxication can be observed in the wounded, in workers manufacturing munitions etc; moreover, lead has been documented to have a negative impact on the intellectual function of children at very low blood concentrations. It is concluded on the basis of the literature overview that replacement of lead by depleted uranium in munitions would be environmentally beneficial or largely insignificant because both lead and uranium are present in the environment.

Depleted uranium instead of lead in munitions: the lesser evil

International Nuclear Information System (INIS)

Jargin, Sergei V

2014-01-01

Uranium has many similarities to lead in its exposure mechanisms, metabolism and target organs. However, lead is more toxic, which is reflected in the threshold limit values. The main potential hazard associated with depleted uranium is inhalation of the aerosols created when a projectile hits an armoured target. A person can be exposed to lead in similar ways. Accidental dangerous exposures can result from contact with both substances. Encountering uranium fragments is of minor significance because of the low penetration depth of alpha particles emitted by uranium: they are unable to penetrate even the superficial keratin layer of human skin. An additional cancer risk attributable to the uranium exposure might be significant only in case of prolonged contact of the contaminant with susceptible tissues. Lead intoxication can be observed in the wounded, in workers manufacturing munitions etc; moreover, lead has been documented to have a negative impact on the intellectual function of children at very low blood concentrations. It is concluded on the basis of the literature overview that replacement of lead by depleted uranium in munitions would be environmentally beneficial or largely insignificant because both lead and uranium are present in the environment. (opinion)

Decision Support Tools for Munitions Response Performance Prediction and Risk Assessment

Science.gov (United States)

2016-09-01

Oldenburg. A discrimination algorithm for UXO using time domain electromagnetic induction . Journal of Environmental and Engineering Geophysics, 6:91...the course of a munitions response project. Unexploded ordnance (UXO), electromagnetic (EM), sensors, electromagnetic induction (EMI), data...approach defines a detection channel that is a linear combination of received channels. The weightings of received channels comprising the optimized

Effect of Co-Composting Cattle Manure with Construction and Demolition Waste on the Archaeal, Bacterial, and Fungal Microbiota, and on Antimicrobial Resistance Determinants.

Science.gov (United States)

Holman, Devin B; Hao, Xiying; Topp, Edward; Yang, Hee Eun; Alexander, Trevor W

2016-01-01

Agricultural operations generate large quantities of manure which must be eliminated in a manner that is consistent with public health guidelines. Meanwhile, construction and demolition waste makes up about 25% of total solid municipal waste. Co-composting of manure with construction and demolition waste offers a potential means to make manure safe for soil amendment and also divert construction and demolition waste from municipal landfills. Therefore, the archaeal, bacterial, and fungal microbiota of two different types of composted cattle manure and one co-composted with construction and demolition waste, were assessed over a 99-day composting period. The microbiota of the three compost mixtures did not differ, but significant changes over time and by sampling depth were observed. Bacillus and Halocella, however, were more relatively abundant in composted manure from cattle fed dried distillers' grains and solubles. Proteobacteria and Bacteroidetes were enriched at day 0 and Firmicutes at day 99. The fungal genus Kernia was the most relatively abundant overall and was enriched at day 0. The concentration of 12 antimicrobial resistance determinants in the compost mixtures was also determined, and 10 of these determinants decreased significantly from days 0 to 99. The addition of construction and demolition waste did not affect the persistence of antimicrobial resistance genes or community structure of the compost microbiota and therefore co-composting construction and demolition waste with cattle manure offers a safe, viable way to divert this waste from landfills.

Effect of Co-Composting Cattle Manure with Construction and Demolition Waste on the Archaeal, Bacterial, and Fungal Microbiota, and on Antimicrobial Resistance Determinants

Science.gov (United States)

Holman, Devin B.; Hao, Xiying; Topp, Edward; Yang, Hee Eun; Alexander, Trevor W.

2016-01-01

Agricultural operations generate large quantities of manure which must be eliminated in a manner that is consistent with public health guidelines. Meanwhile, construction and demolition waste makes up about 25% of total solid municipal waste. Co-composting of manure with construction and demolition waste offers a potential means to make manure safe for soil amendment and also divert construction and demolition waste from municipal landfills. Therefore, the archaeal, bacterial, and fungal microbiota of two different types of composted cattle manure and one co-composted with construction and demolition waste, were assessed over a 99-day composting period. The microbiota of the three compost mixtures did not differ, but significant changes over time and by sampling depth were observed. Bacillus and Halocella, however, were more relatively abundant in composted manure from cattle fed dried distillers’ grains and solubles. Proteobacteria and Bacteroidetes were enriched at day 0 and Firmicutes at day 99. The fungal genus Kernia was the most relatively abundant overall and was enriched at day 0. The concentration of 12 antimicrobial resistance determinants in the compost mixtures was also determined, and 10 of these determinants decreased significantly from days 0 to 99. The addition of construction and demolition waste did not affect the persistence of antimicrobial resistance genes or community structure of the compost microbiota and therefore co-composting construction and demolition waste with cattle manure offers a safe, viable way to divert this waste from landfills. PMID:27300323

Life cycle assessment and life cycle costing for demolition waste management

NARCIS (Netherlands)

Hu, M.; Miranda-Xicotencat, B.; Ita-Nagy, D.; Prado, V.; Guinée, J.B.; van Roekel, E; Huismans, R.; Rens, F.; Lotfi, Somayeh; Di Maio, F.; Di Maio, F.; Lotfi, S.; Bakker, M.; Hu, M.; Vahidi, A.

2017-01-01

Ninety five percent of the construction and demolition waste is recycled in the Netherlands. Most of it is used for low value applications such as road base materials; the use of secondary material in buildings is still less than 3%7. In order to recover waste for higher value applications,

Portland blended cements: demolition ceramic waste management

International Nuclear Information System (INIS)

Trezza, M.A.; Zito, S.; Tironi, A.; Irassar, E.F.; Rahhal, V.F.

2017-01-01

Demolition ceramic wastes (DCWs) were investigated in order to determine their potential use as supplementary cementitious materials in Portland Blended Cements (PBCs). For this purpose, three ceramic wastes were investigated. After characterization of the materials used, the effect of ceramic waste replacement (8, 24 and 40% by mass) was analyzed. Pozzolanic activity, hydration progress, workability and compressive strength were determined at 2, 7 and 28 days. The results showed that the ground wastes behave as filler at an early age, but as hydration progresses, the pozzolanic activity of ceramic waste contributes to the strength requirement. [es

Evaluation of the metabolic fate of munitions material (TNT & RDX) in plant systems and initial assessment of material interaction with plant genetic material. Validation of the metabolic fate of munitions materials (TNT, RDX) in mature crops

Energy Technology Data Exchange (ETDEWEB)

Fellows, R.J.; Harvey, S.D.; Cataldo, D.A.

1995-09-01

The goals of this effort were to confirm and expand data related to the behavior and impacts of munitions residues upon human food chain components. Plant species employed included corn (Zea mays), alfalfa (Medicago sativa). spinach (Spinacea oleraceae), and carrot (Daucus carota). Plants were grown from seed to maturity (70 to 120 days) in a low-fertility soil (Burbank) amended with either {sup 14}C-TNT or {sup 14}C-RDX at which time they were harvested and analyzed for munitions uptake, partitioning, and chemical form of the munition or munition-metabolite. All four of the plant species used in this study accumulated the {sup 14}C-TNT- and RDX-derived label. The carrot, alfalfa, and corn demonstrated a higher percentage of label retained in the roots (62, 73, and 83% respectively). The spinach contained less activity in its root (36%) but also contained the highest TNT specific activity observed (>4600 jig TNT equivalents/g dry wt.). The specific uptake values of RDX for the spinach and alfalfa were comparable to those previously reported for wheat and bean (314 to 590 {mu}g RDX-equivalents/g dry wt. respectively). An exception to this may be the carrot where the specific activity was found to exceed 4200 {mu}g RDX-equivalents/g dry wt. in the shoot. The total accumulation of TNT by the plants ranged from 1.24% for the spinach to 2.34% for the carrot. The RDX plants ranging from 15% for the spinach to 37% for the carrot. There was no identifiable TNT or amino dinitrotoluene (ADNT) isomers present in the plants however, the parent RDX compound was found at significant levels in the shoot of alfalfa (> 1 80 {mu}g/g) and corn (>18 {mu}g/g).

Assessment of leaching from Construction & Demolition Waste concrete

DEFF Research Database (Denmark)

Butera, Stefania; Christensen, Thomas Højlund; Astrup, Thomas

2012-01-01

Construction and demolition waste features two very important properties when considering its management options: the large amounts, and the low environmental hazardousness. Therefore, concrete waste can be recycled relatively easily: most common end-of-life option is utilization as unbound...... approaches exist, often implying unrealistic or not relevant conditions if compared to real life utilization scenarios. A modified version of the CEN/TS 14405 column percolation test has been implemented on four crushed concrete samples, with the purpose of analysing the release of chromium, one...

Dehomed: the impacts of house demolitions on the well-being of women from the unrecognized Bedouin-Arab villages in the Negev/Israel.

Science.gov (United States)

Gottlieb, Nora; Feder-Bubis, Paula

2014-09-01

Thirty-five Bedouin-Arab villages in South Israel are regarded illegal settlements by the state. Consequently, the residents׳ homes are subject to demolition. Based on 12 semi-structured multiple-participant interviews, this paper examines the house demolitions׳ impacts on women, in the context of gendered constructions of social roles and space. It highlights that the marginalized position of Arab-Bedouin women - as women in a patriarchal community, as members of a minority within Israeli society, and as residents of an "invisible" settlement - contributes to the devastating effects of the house demolitions. In particular, the study׳s results show that the house demolitions inflict severe personal and collective trauma, amplified by women׳s primary role as mothers. Paradoxically, the very same role also becomes a source of resilience and political resistance, as women act to defend a sense of home and restore family life in the face of state violence. Copyright © 2014 Elsevier Ltd. All rights reserved.

Recycling of rubble from building demolition for low-shrinkage concretes.

Science.gov (United States)

Corinaldesi, Valeria; Moriconi, Giacomo

2010-04-01

In this project concrete mixtures were prepared that were characterized by low ductility due to desiccation by using debris from building demolition, which after a suitable treatment was used as aggregate for partial replacement of natural aggregates. The recycled aggregate used came from a recycling plant, in which rubble from building demolition was selected, crushed, cleaned, sieved, and graded. Such aggregates are known to be more porous as indicated by the Saturated Surface Dry (SSD) moisture content. The recycled concrete used as aggregates were added to the concrete mixture in order to study their influence on the fresh and hardened concrete properties. They were added either after water pre-soaking or in dry condition, in order to evaluate the influence of moisture in aggregates on the performance of concrete containing recycled aggregate. In particular, the effect of internal curing, due to the use of such aggregates, was studied. Concrete behavior due to desiccation under dehydration was studied by means of both drying shrinkage test and German angle test, through which shrinkage under the restrained condition of early age concrete can be evaluated. Copyright 2009 Elsevier Ltd. All rights reserved.

An estimation framework for building information modeling (BIM)-based demolition waste by type.

Science.gov (United States)

Kim, Young-Chan; Hong, Won-Hwa; Park, Jae-Woo; Cha, Gi-Wook

2017-12-01

Most existing studies on demolition waste (DW) quantification do not have an official standard to estimate the amount and type of DW. Therefore, there are limitations in the existing literature for estimating DW with a consistent classification system. Building information modeling (BIM) is a technology that can generate and manage all the information required during the life cycle of a building, from design to demolition. Nevertheless, there has been a lack of research regarding its application to the demolition stage of a building. For an effective waste management plan, the estimation of the type and volume of DW should begin from the building design stage. However, the lack of tools hinders an early estimation. This study proposes a BIM-based framework that estimates DW in the early design stages, to achieve an effective and streamlined planning, processing, and management. Specifically, the input of construction materials in the Korean construction classification system and those in the BIM library were matched. Based on this matching integration, the estimates of DW by type were calculated by applying the weight/unit volume factors and the rates of DW volume change. To verify the framework, its operation was demonstrated by means of an actual BIM modeling and by comparing its results with those available in the literature. This study is expected to contribute not only to the estimation of DW at the building level, but also to the automated estimation of DW at the district level.

Construction and demolition waste as a source of PVC for recycling.

Science.gov (United States)

Prestes, Sabrina Moretto Darbello; Mancini, Sandro Donnini; Rodolfo, Antonio; Keiroglo, Raquel Carramillo

2012-02-01

Construction and demolition waste can contain considerable amounts of polyvinyl chloride (PVC). This paper describes a study of the recycling of PVC pipes collected from such waste materials. In a sorting facility for the specific disposal of construction and demolition waste, PVC was found to represent one-third of the plastics separated by workers. Pipes were sorted carefully to preclude any possible contamination by poly(ethylene terephthalate) (PET) found in the waste. The material was ground into two distinct particle sizes (final mesh of 12.7 and 8 mm), washed, dried and recycled. The average formulation of the pipes was determined based on ash content tests and used in the fabrication of a similar compound made mainly of virgin PVC. Samples of recycled pipes and of compound based on virgin material were subjected to tensile and impact tests and provided very similar results. These results are a good indication of the application potential of the recycled material and of the fact that longer grinding to obtain finer particles is not necessarily beneficial.

Disposal of chemical agents and munitions stored at Pine Bluff Arsenal, Pine Bluff, Arkansas. Final phase 1, Environmental report

Energy Technology Data Exchange (ETDEWEB)

Ensminger, J.T.; Hillsman, E.L.; Johnson, R.D.; Morrisey, J.A.; Staub, W.P.; Boston, C.R.; Hunsaker, D.B.; Leibsch, E.; Rickert, L.W.; Tolbert, V.R.; Zimmerman, G.P.

1991-09-01

The Pine Bluff Arsenal (PBA) near Pine Bluff, Arkansas, is one of eight continental United States (CONUS) Army installations where lethal unitary chemical agents and munitions are stored and where destruction of agents and munitions is proposed under the Chemical Stockpile Disposal Program (CSDP). The chemical agent inventory at PBA consists of approximately 12%, by weight, of the total US stockpile. The destruction of the stockpile is necessary to eliminate the risk to the public from continued storage and to dispose of obsolete and leaking munitions. In 1988 the US Army issued a Final Programmatic Environmental Impact Statement (FPEIS) for the CSDP that identified on-site disposal of agents and munitions as the environmentally preferred alternative (i.e., the alternative with the least potential to cause significant adverse impacts). The purpose of this report is to examine the proposed implementation of on-site disposal at PBA in light of more recent and more detailed data than those on which the FPEIS is based. New population data were used to compute fatalities using the same computation methods and values for all other parameters as in the FPEIS. Results indicate that all alternatives are indistinguishable when the potential health impacts to the PBA community are considered. However, risks from on-site disposal are in all cases equal to or less than risks from other alternatives. Furthermore, no unique resources with the potential to prevent or delay implementation of on-site disposal at PBA have been identified.

Optimization of Intelligent Munition Warfare Using Agent-Based Simulation Software and Design of Experiments Methodology

National Research Council Canada - National Science Library

Floersheim, Bruce; Hou, Gene

2006-01-01

... mechanism for a number of vehicles caught in the killzone. Thus, it is useful to study and attempt to model through equations and simulation the interaction between enemy agents and these new munitions...

Safety and vulnerability simulation of munitions; Modelisation du comportement de munitions en securite et vulnerabilite

Energy Technology Data Exchange (ETDEWEB)

Desailly, D.; Briquet, B.; Brunet, P.; Guegant, Y.; Houdusse, D.; Prost, M. [Groupe SNPE Propulsion/ Centre de Recherches du Boucher, 91 - Vert le Petit (France)

2002-09-01

Vulnerability of new weapon systems to accidental and hostile environments is a major concern for military operations and many research programs have been so investigated of SNPE Propulsion. Before they were accepted as being safe and suitable for introduction into military inventories systems underwent a wide range of expensive type qualification trials. There was a need therefore, to develop a greater understanding of the reaction mechanisms that affect the behaviour of confined energetic materials when subjected to external stimuli and computer models to control the resulting hazard. As part of this program SNPE Propulsion has developed a method for modelling Cook-off response in order to master the design of insensitive munitions (IM). The behavior of energetic materials when they are submitted to a thermal threat is complex and follows two different time scales: thermochemical processes, counted in minutes even hours whereas pyrotechnic reaction may require a few microseconds. It was shown that the reaction level is ruled by the competition between pressure generated from the cook-off reaction and stress release resulting from break-up confinement. After self-ignition phenomenon and under some confinement and thermal conditions burning can accelerate to deflagration and lead to a deflagration to detonation transition (DDT) event. The method requires'modular tools describing each physical phenomenon. Works have been first focused on the development of experimental facilities to characterise thermal chemical properties and reactivity of thermally damaged energetic material. Consequently the first part of the model describing self-heating and pyrolysis processes has been implemented in an implicit solver. Simulations have shown quite accurate predictions (ignition temperature, time to event) and proved the effectiveness of this approach. Recent developments are.thus concentrated on the numerical modelling of the reaction violence level prediction hence a

Silica dust control in small-scale building/structure demolition operations using good work practice guidance

International Nuclear Information System (INIS)

Muianga, C V; Rice, C H; Succop, P

2009-01-01

Work practices can influence exposure, especially in small-scale operations conducted by mobile work crews. This study evaluated the use of information on good work practice in control guidance sheets adapted from UK Silica Essentials guidance sheets by trained workers and supervisors employed in small-scale concrete and masonry demolition operations. A one-page employee silica task-based control guidance sheet for each of four demolition tasks and multiple-page silica control guidance for supervisors were developed. Interactive, hands-on worker training on these task-based good work practice controls was developed. Training was presented to 26 participants from two demolition crews. Feedback on the training and task-based good work practice control guidance sheets was elicited. Observations of work practices were made before and after training. Participants indicated gains in knowledge and checklists were used to document skill attainment. The quality of the training and usefulness of the material/skills was rated high by trainees. Increased use of water to suppress dust and wet cleaning methods on the job were documented following the training. Additional follow-up after training is required to determine long-term impact on sustained changes in work practices, and to evaluate the need for refresher training.

Silica dust control in small-scale building/structure demolition operations using good work practice guidance

Science.gov (United States)

Muianga, C. V.; Rice, C. H.; Succop, P.

2009-02-01

Work practices can influence exposure, especially in small-scale operations conducted by mobile work crews. This study evaluated the use of information on good work practice in control guidance sheets adapted from UK Silica Essentials guidance sheets by trained workers and supervisors employed in small-scale concrete and masonry demolition operations. A one-page employee silica task-based control guidance sheet for each of four demolition tasks and multiple-page silica control guidance for supervisors were developed. Interactive, hands-on worker training on these task-based good work practice controls was developed. Training was presented to 26 participants from two demolition crews. Feedback on the training and task-based good work practice control guidance sheets was elicited. Observations of work practices were made before and after training. Participants indicated gains in knowledge and checklists were used to document skill attainment. The quality of the training and usefulness of the material/skills was rated high by trainees. Increased use of water to suppress dust and wet cleaning methods on the job were documented following the training. Additional follow-up after training is required to determine long-term impact on sustained changes in work practices, and to evaluate the need for refresher training.

Nuclear Rocket Facility Decommissioning Project: Controlled Explosive Demolition of Neutron-Activated Shield Wall

International Nuclear Information System (INIS)

Michael R, Kruzic

2008-01-01

Located in Area 25 of the Nevada Test Site (NTS), the Test Cell A (TCA) Facility (Figure 1) was used in the early to mid-1960s for testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program, to further space travel. Nuclear rocket testing resulted in the activation of materials around the reactors and the release of fission products and fuel particles. The TCA facility, known as Corrective Action Unit 115, was decontaminated and decommissioned (D and D) from December 2004 to July 2005 using the Streamlined Approach for Environmental Restoration (SAFER) process, under the Federal Facility Agreement and Consent Order. The SAFER process allows environmental remediation and facility closure activities (i.e., decommissioning) to occur simultaneously, provided technical decisions are made by an experienced decision maker within the site conceptual site model. Facility closure involved a seven-step decommissioning strategy. First, preliminary investigation activities were performed, including review of process knowledge documentation, targeted facility radiological and hazardous material surveys, concrete core drilling and analysis, shield wall radiological characterization, and discrete sampling, which proved to be very useful and cost-effective in subsequent decommissioning planning and execution and worker safety. Second, site setup and mobilization of equipment and personnel were completed. Third, early removal of hazardous materials, including asbestos, lead, cadmium, and oil, was performed ensuring worker safety during more invasive demolition activities. Process piping was to be verified void of contents. Electrical systems were de-energized and other systems were rendered free of residual energy. Fourth, areas of high radiological contamination were decontaminated using multiple methods. Contamination levels varied across the facility. Fixed beta/gamma contamination levels ranged up to 2 million disintegrations per minute (dpm)/100

Nuclear Rocket Facility Decommissioning Project: Controlled Explosive Demolition of Neutron-Activated Shield Wall

Energy Technology Data Exchange (ETDEWEB)

Michael R. Kruzic

2008-06-01

Located in Area 25 of the Nevada Test Site (NTS), the Test Cell A (TCA) Facility (Figure 1) was used in the early to mid-1960s for testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program, to further space travel. Nuclear rocket testing resulted in the activation of materials around the reactors and the release of fission products and fuel particles. The TCA facility, known as Corrective Action Unit 115, was decontaminated and decommissioned (D&D) from December 2004 to July 2005 using the Streamlined Approach for Environmental Restoration (SAFER) process, under the Federal Facility Agreement and Consent Order. The SAFER process allows environmental remediation and facility closure activities (i.e., decommissioning) to occur simultaneously, provided technical decisions are made by an experienced decision maker within the site conceptual site model. Facility closure involved a seven-step decommissioning strategy. First, preliminary investigation activities were performed, including review of process knowledge documentation, targeted facility radiological and hazardous material surveys, concrete core drilling and analysis, shield wall radiological characterization, and discrete sampling, which proved to be very useful and cost-effective in subsequent decommissioning planning and execution and worker safety. Second, site setup and mobilization of equipment and personnel were completed. Third, early removal of hazardous materials, including asbestos, lead, cadmium, and oil, was performed ensuring worker safety during more invasive demolition activities. Process piping was to be verified void of contents. Electrical systems were de-energized and other systems were rendered free of residual energy. Fourth, areas of high radiological contamination were decontaminated using multiple methods. Contamination levels varied across the facility. Fixed beta/gamma contamination levels ranged up to 2 million disintegrations per minute (dpm)/100

Cost Of Compliance On Munitions Consolidation From Lualualei To West Loch

Science.gov (United States)

2017-12-01

well as the opportunity to drastically reduce the transportation of ordnance to and from the Lualualei Annex through local community roads and areas...single road and the availability of CULT trucks and/or drivers that could impede an expeditious response in a contingency operation. This project...to distribute munitions to the fleet. This consolidation plan will also reduce the infrastructure costs for ordnance storage, maintenance , and

Mixture optimization of cement treated demolition waste with recycled masonry and concrete

NARCIS (Netherlands)

Xuan, D.X.; Houben, L.J.M.; Molenaar, A.A.A.; Shui, Z.H,

2011-01-01

Due to environmental reasons and the shortage of natural resources, it is greatly valuable to recycle construction and demolition waste (CDW) as much as possible. One of effective ways to reuse more CDW is to produce a cemented road base material. The recycled CDW however is a mix of recycled

24 CFR 970.15 - Specific criteria for HUD approval of demolition requests.

Science.gov (United States)

2010-04-01

... modifications is cost-effective to return the public housing project or portion of the project to useful life... 24 Housing and Urban Development 4 2010-04-01 2010-04-01 false Specific criteria for HUD approval of demolition requests. 970.15 Section 970.15 Housing and Urban Development Regulations Relating to...

Trends in demolition planning and in the cutting techniques employed; Trends bei der Rueckbauplanung und den verwendeten Schneidverfahren

Energy Technology Data Exchange (ETDEWEB)

Brueggemann, Pascal [NUKEM Technologies GmbH, Alzenau (Germany)

2009-08-15

The past couple of years have seen the continuous further development of cutting techniques employed in demolishing nuclear facilities. This trend is continuing. After mostly mechanical cutting techniques had been used initially, there has been a tendency in the past few years to make increasing use of thermal cutting. Reasons for this preference are the reduced space requirement and the advantages this technique offers in remote handling because of the low weight and the small dimensions of the cutting heads, and the high flexibility in materials to be cut. This results in greater planning reliability in calculating quotations and performing the demolition work. The emissions generated by these techniques are manageable reliably at low additional expense for the required extraction and filter systems. Thermal cutting is likely to achieve wide use in dismantling and demolition of nuclear plant components also in the future. Advanced developments in computer hardware and software allow more and more detailed planning of demolition work. While, in the past, CAD had been applied only to generate two-dimensional drawings, current 3D applications allow animated representations of entire demolition scenes with high accuracy in detail. In this way, potential problems associated with handling large components or using manipulators for cutting can be detected and solved much more easily in the preparatory phase. Although current CAD use can be no substitute for mockup tests, it does help to enhance clearly reliability in planning prior to running mockup tests. (orig.)

Dissolution of NTO, DNAN, and Insensitive Munitions Formulations and Their Fates in Soils

Science.gov (United States)

2014-09-01

plastic bags to save the (a) (b) ERDC/CRREL TR-14-23 10 sample even if the bottle should break from ice formation. During each collection, we...Bacillus sp. Biodegradation 23 (2): 287–295. Prak, D.L., and D. O’Sullivan. 2012. Photochemical Transformation of Munitions Constituents in Marine

Controlled damaging and repair of self-organized nanostructures by atom manipulation at room temperature

International Nuclear Information System (INIS)

Gurlu, O; Houselt, A van; Thijssen, W H A; Ruitenbeek, J M van; Poelsema, B; Zandvliet, H J W

2007-01-01

The possibility of controlled local demolition and repair of the recently discovered self-organized Pt nanowires on Ge(001) surfaces has been explored. These nanowires are composed of Pt dimers, which are found to be rather weakly bound to the underlying substrate. Using this property, we demonstrate the possibility of carrying the constituting dimers of the Pt nanowires from point to point with atomic precision at room temperature. Pt dimers can be picked-up in two configurations: (i) a horizontal configuration at the tip apex, resulting in double tip images and (ii) a configuration where the Pt dimer is attached to the side of the tip apex, resulting in well-defined atomically resolved images

Overview regarding construction and demolition waste in Spain.

Science.gov (United States)

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Morán-Del Pozo, Julia M; Guerra-Romero, M Ignacio

2015-01-01

The construction sector comprises a number of activities that may result in environmental impacts of considerable magnitude, waste generation being one of the major negative effects of this industry due to the large streams generated. Proper knowledge of the environmental problem caused by the sector is of great importance in order to achieve an effective waste management. Thus, this paper analyse the Spanish situation regarding construction and demolition waste (CDW) compared with other European Union countries; which sets out the current figures of the CDW scenario (legislation, generation, composition, treatment and market) as well as the difficulties encountered when handling this residue.

Demolition of one of the old barracks

CERN Multimedia

2002-01-01

Many people at CERN will no doubt remember having rented accommodation in the four barracks-type huts near Entrance A. The rates were certainly rock bottom but it was hardly the Ritz! Put up at the end of the 1950s, they were abandoned in favour of the Saint-Genis-Pouilly hostel and the Meyrin site hostels. As they no longer meet current safety standards, they will all ultimately have to be demolished. One of them, situated immediately below the HV power line, has just been demolished at the request of the Swiss electricity company Energie Ouest Suisse. With its demolition, a little piece of CERN's social history has gone for ever.

Chemical sulphate removal for treatment of construction and demolition debris leachate.

Science.gov (United States)

Kijjanapanich, Pimluck; Annachhatre, Ajit P; Esposito, Giovanni; Lens, Piet N L

2014-08-01

Construction and demolition debris (CDD) is a product of construction, renovation or demolition activities. It has a high gypsum content (52.4% of total gypsum), concentrated in the CDD sand (CDDS) fraction. To comply with the posed limit of the maximum amount of sulphate present in building sand, excess sulphate needs to be removed. In order to enable reuse of CDDS, a novel treatment process is developed based on washing of the CDDS to remove most of the gypsum, and subsequent sulphate removal from the sulphate-rich CDDS leachate. This study aims to assess chemical techniques, i.e. precipitation and adsorption, for sulphate removal from the CDDS leachate. Good sulphate removal efficiencies (up to 99.9%) from the CDDS leachate can be achieved by precipitation with barium chloride (BaCl2) and lead(II) nitrate (Pb(NO3)2). Precipitation with calcium chloride (CaCl2), calcium carbonate (CaCO3) and calcium oxide (CaO) gave less efficient sulphate removal. Adsorption of sulphate to aluminium oxide (Al2O3) yielded a 50% sulphate removal efficiency, whereas iron oxide-coated sand as adsorbent gave only poor (10%) sulphate removal efficiencies.

High Flux Isotopes Reactor (HFIR) Cooling Towers Demolition Waste Management

Energy Technology Data Exchange (ETDEWEB)

Pudelek, R. E.; Gilbert, W. C.

2002-02-26

This paper describes the results of a joint initiative between Oak Ridge National Laboratory, operated by UT-Battelle, and Bechtel Jacobs Company, LLC (BJC) to characterize, package, transport, treat, and dispose of demolition waste from the High Flux Isotope Reactor (HFIR), Cooling Tower. The demolition and removal of waste from the site was the first critical step in the planned HFIR beryllium reflector replacement outage scheduled. The outage was scheduled to last a maximum of six months. Demolition and removal of the waste was critical because a new tower was to be constructed over the old concrete water basin. A detailed sampling and analysis plan was developed to characterize the hazardous and radiological constituents of the components of the Cooling Tower. Analyses were performed for Resource Conservation and Recovery Act (RCRA) heavy metals and semi-volatile constituents as defined by 40 CFR 261 and radiological parameters including gross alpha, gross beta, gross gamma, alpha-emitting isotopes and beta-emitting isotopes. Analysis of metals and semi-volatile constituents indicated no exceedances of regulatory limits. Analysis of radionuclides identified uranium and thorium and associated daughters. In addition 60Co, 99Tc, 226Rm, and 228Rm were identified. Most of the tower materials were determined to be low level radioactive waste. A small quantity was determined not to be radioactive, or could be decontaminated. The tower was dismantled October 2000 to January 2001 using a detailed step-by-step process to aid waste segregation and container loading. The volume of waste as packaged for treatment was approximately 1982 cubic meters (70,000 cubic feet). This volume was comprised of plastic ({approx}47%), wood ({approx}38%) and asbestos transite ({approx}14%). The remaining {approx}1% consisted of the fire protection piping (contaminated with lead-based paint) and incidental metal from conduit, nails and braces/supports, and sludge from the basin. The waste

Disposal of chemical agents and munitions stored at Umatilla Depot Activity, Hermiston, Oregon. Final Phase 1 environmental report

Energy Technology Data Exchange (ETDEWEB)

Zimmerman, G.P.; Hillsman, E.L.; Johnson, R.O.; Miller, R.L.; Patton, T.G.; Schoepfle, G.M.; Tolbert, V.R.; Feldman, D.L.; Hunsaker, D.B. Jr.; Kroodsma, R.L.; Morrissey, J.; Rickert, L.W.; Staub, W.P.; West, D.C.

1993-02-01

The Umatilla Depot Activity (UMDA) near Hermiston, Oregon, is one of eight US Army installations in the continental United States where lethal unitary chemical agents and munitions are stored, and where destruction of agents and munitions is proposed under the Chemical Stockpile Disposal Program (CSDP). The chemical agent inventory at UMDA consists of 11.6%, by weight, of the total US stockpile. The destruction of the stockpile is necessary to eliminate the risk to the public from continued storage and to dispose of obsolete and leaking munitions. In 1988 the US Army issued a Final Programmatic Environmental Impact Statement (FPEIS) for the CSDP that identified on-site disposal of agents and munitions as the environmentally preferred alternative (i.e., the alternative with the least potential to cause significant adverse impacts), using a method based on five measures of risk for potential human health and ecosystem/environmental effects; the effectiveness and adequacy of emergency preparedness capabilities also played a key role in the FPEIS selection methodology. In some instances, the FPEIS included generic data and assumptions that were developed to allow a consistent comparison of potential impacts among programmatic alternatives and did not include detailed conditions at each of the eight installations. The purpose of this Phase 1 report is to examine the proposed implementation of on-site disposal at UMDA in light of more recent and more detailed data than those included in the FPEIS. Specifically, this Phase 1 report is intended to either confirm or reject the validity of on-site disposal for the UMDA stockpile. Using the same computation methods as in the FPEIS, new population data were used to compute potential fatalities from hypothetical disposal accidents. Results indicate that onsite disposal is clearly preferable to either continued storage at UMDA or transportation of the UMDA stockpile to another depot for disposal.

Quantum non-demolition phonon counter with a hybrid optomechnical system

Science.gov (United States)

Song, Qiao; Zhang, KeYe; Dong, Ying; Zhang, WeiPing

2018-05-01

A phonon counting scheme based on the control of polaritons in an optomechanical system is proposed. This approach permits us to measure the number of phonons in a quantum non-demolition (QND) manner for arbitrary modes not limited by the frequency matching condition as in usual photon-phonon scattering detections. The performance on phonon number transfer and quantum state transfer of the counter are analyzed and simulated numerically by taking into account all relevant sources of noise.

Acute toxicity of sea-dumped chemical munitions: Luminating the environmental toxicity of legacy compounds

DEFF Research Database (Denmark)

Mohammed Abdullah Christensen, Ilias; Sanderson, Hans; Baatrup, Erik

2016-01-01

As a result of the disarmament of Germany after the Second World War, 65,000 tons of chemical munitions were dumped in the Baltic Sea. Approximately 13,000 tons containing chemical warfare agents (CWAs) of which 11,000 tons were dumped in the Bornholm Basin east of Bornholm. This paper addresses...

Brownfields Recover Your Resources - Reduce, Reuse, and Recycle Construction and Demolition Materials at Land Revitalization Projects

Science.gov (United States)

This document provides background information on how the sustainable reuse of brownfield properties includes efforts to reduce the environmental impact by reusing and recycling materials generated during building construction, demolition, or renovation.

HEAVY METALS IN RECOVERED FINES FOR CONSTRUCTION AND DEMOLITION DEBRIS RECYCLING FACILITIES IN FLORIDA

Science.gov (United States)

A major product recovered from the processing and recycling of construction and demolition (C&D) debris is screened soil, also referred to as fines. A proposed reuse option for C&D debris fines is fill material, typically in construction projects as a substitute for natural soil....

78 FR 40705 - Takes of Marine Mammals Incidental to Specified Activities; Demolition and Construction...

Science.gov (United States)

2013-07-08

... (Zalophus californianus), and northern elephant seals (Mirounga angustirostris) incidental to demolition and... activities by the general public. Over the last three years (2010 through 2012), an average of 1,556,184..., but because of basic year-round working condition needs for the lifeguards and the demand for...

Assessment of different construction and demolition waste management approaches

Directory of Open Access Journals (Sweden)

Manal S. Abdelhamid

2014-12-01

Full Text Available The waste generated from construction and demolition sites is considered one of the most irritating problems in Egypt. In the last 10 years some effort has been made toward solving this problem, the most outstanding is the newly issued Egyptian rating system “Green Pyramids Rating System”. It emphasizes on waste management and particularly “site provision and environment” which contributes to 75% of the management category score. However the traditional practice which is limited to dumping all the generated waste is still dominating. The absence of sustainable practices in construction sector in Egypt led to the lack in financial and environmental data. From strategic perspective, the research aims at developing a detailed procedure to evaluate two construction and demolition waste management approaches by means of Decision Matrix technique. A detailed study is introduced for the two approaches; for each approach a flow chart is developed to demonstrate its lifecycle, as well as the cost break down structure and the different stakeholders’ roles. A penetration discussion of the pros and cons for each approach was developed accordingly and came out with sixteen influencing attributes for both approaches. The previous steps paved the ground to construct a Decision Matrix to decide on one of the approaches from a strategic environmentally oriented perspective. The study relied on the detailed and deep demonstration of the two approaches to justify the assigned weight for attributes and scores for corresponding approach. From a strategic perspective, the decision came out in favor of the more environmentally friendly approach.

77 FR 70684 - Safety Zone; Bridge Demolition Project; Indiana Harbor Canal, East Chicago, IN

Science.gov (United States)

2012-11-27

... environmental risk to health or risk to safety that may disproportionately affect children. 10. Indian Tribal... the Cline Avenue bridge in East Chicago, IN. The Captain of the Port, Sector Lake Michigan, has determined that this demolition project will pose a significant risk to public safety and property. Such...

Gentrification in black and white: the racial impact of public housing demolition in American cities.

Science.gov (United States)

Goetz, Edward

2011-01-01

The gentrification that has transformed high-poverty neighbourhoods in US cities since the mid 1990s has been characterised by high levels of state reinvestment. Prominent among public-sector interventions has been the demolition of public housing and in some cases multimillion dollar redevelopment efforts. In this paper, the racial dimension of state-supported gentrification in large US cities is examined by looking at the direct and indirect displacement induced by public housing transformation. The data show a clear tendency towards the demolition of public housing projects with disproportionately high African American occupancy. The pattern of indirect displacement is more varied; public housing transformation has produced a number of paths of neighbourhood change. The most common, however, involve significant reductions in poverty, sometimes associated with Black to White racial turnover and sometimes not. The findings underscore the central importance of race in understanding the dynamics of gentrification in US cities.

Total and respirable dust exposures among carpenters and demolition workers during indoor work in Denmark

DEFF Research Database (Denmark)

Kirkeskov, Lilli; Hanskov, Dorte Jessing Agerby; Brauer, Charlotte

2016-01-01

BACKGROUND: Within the construction industry the risk of lung disorders depends on the specific professions probably due to variations in the levels of dust exposure, and with dust levels depending on the work task and job function. We do not know the extent of exposure in the different professions...... was 3.90 (95 % confidence interval 1.13-13.5) mg/m(3). Dust exposure varied depending on work task for both professions. The dustiest work occurred during demolition, especially when it was done manually. Only few workers used personal respiratory protection and only while performing the dustiest work...... or the variation between the different work tasks. The purpose of this study was therefore to assess if there were differences in dust exposure between carpenters and demolition workers who were expected to have low and high dust exposure, respectively. METHODS: Through interviews of key persons...

Quality and quantity of construction and demolition waste in Tehran.

Science.gov (United States)

Asgari, Alireza; Ghorbanian, Tahereh; Yousefi, Nader; Dadashzadeh, Dariush; Khalili, Fatemeh; Bagheri, Amin; Raei, Mehdi; Mahvi, Amir Hossein

2017-01-01

In recent years the generation rate of construction and demolition waste (C&D) has significantly augmented. The aim of this study was to assessed the quality and quantity of construction and demolition waste in Tehran (capital of Iran). Questionnaire methods were used for estimating the amount of generated C&D wastes national statistical data and typical waste generation data. In order to defining the composition of C&D waste, trucks were randomly selected and their wastes were separated and weighted. According to obtained results, about 82,646,051 m 3 of C&D waste (average 16,529,210 m 3 per year) were generated during 2011 to 2016 which only about 26% of them has been recycled. Mixing sand and cement, concrete, broken bricks and soil have the highest amount of the composition of C&D waste in Tehran that was 30, 19, 18 and 11%, respectively. Based on the results, about 2,784,158 t of the waste will generate in 2025 and this is approximately 122% higher than wastes generate in 2016. Based on MAPSA's data, 360 teams of personnel cruise and control the illegal disposals, but due to the expansion of Tehran this number of teams is inadequate and can't be effective in controlling the situation. In general, the overall condition of C&D waste management in Tehran seems undesirable and needs to be updated based on the experience of successful countries in this field.

77 FR 63732 - Safety Zone; Bridge Demolition Project; Indiana Harbor Canal, East Chicago, IN

Science.gov (United States)

2012-10-17

..., Protection of Children from Environmental Health Risks and Safety Risks. This rule is not an economically significant rule and does not create an environmental risk to health or risk to safety that may.... The Captain of the Port, Sector Lake Michigan, has determined that this demolition project will pose a...

Cultural Resource Assessment of the Test Area North Demolition Landfill at the Idaho National Engineering and Environmental Laboratory

Energy Technology Data Exchange (ETDEWEB)

Brenda R. Pace

2003-07-01

The proposed new demolition landfill at Test Area North on the Idaho National Engineering and Environmental Laboratory (INEEL) will support ongoing demolition and decontamination within the facilities on the north end of the INEEL. In June of 2003, the INEEL Cultural Resource Management Office conducted archival searches, field surveys, and coordination with the Shoshone-Bannock Tribes to identify all cultural resources that might be adversely affected by the project and to provide recommendations to protect those listed or eligible for listing on the National Register of Historic Places. These investigations showed that landfill construction and operation would affect two significant cultural resources. This report outlines protective measures to ensure that these effects are not adverse.

Cultural Resource Assessment of the Test Area North Demolition Landfill at the Idaho National Engineering and Environmental Laboratory

International Nuclear Information System (INIS)

Brenda R. Pace

2003-01-01

The proposed new demolition landfill at Test Area North on the Idaho National Engineering and Environmental Laboratory (INEEL) will support ongoing demolition and decontamination within the facilities on the north end of the INEEL. In June of 2003, the INEEL Cultural Resource Management Office conducted archival searches, field surveys, and coordination with the Shoshone-Bannock Tribes to identify all cultural resources that might be adversely affected by the project and to provide recommendations to protect those listed or eligible for listing on the National Register of Historic Places. These investigations showed that landfill construction and operation would affect two significant cultural resources. This report outlines protective measures to ensure that these effects are not adverse

Properties of Concrete Paving Blocks and Hollow Tiles with Recycled Aggregate from Construction and Demolition Wastes.

Science.gov (United States)

Rodríguez, Carlos; Miñano, Isabel; Aguilar, Miguel Ángel; Ortega, José Marcos; Parra, Carlos; Sánchez, Isidro

2017-11-30

In recent years there has been an increasing tendency to recycle the wastes generated by building companies in the construction industry, demolition wastes being the most important in terms of volume. The aim of this work is to study the possibility of using recycled aggregates from construction and demolition wastes in the preparation of precast non-structural concretes. To that purpose, two different percentages (15% and 30%) of natural aggregates were substituted by recycled aggregates in the manufacture of paving blocks and hollow tiles. Dosages used by the company have not been changed by the introduction of recycled aggregate. Precast elements have been tested by means of compressive and flexural strength, water absorption, density, abrasion, and slipping resistance. The results obtained show the possibility of using these wastes at an industrial scale, satisfying the requirements of the Spanish standards for these elements.

Munitions and Explosives of Concern Survey Methodology and In-field Testing for Wind Energy Areas on the Atlantic Outer Continental Shelf

Science.gov (United States)

DuVal, C.; Carton, G.; Trembanis, A. C.; Edwards, M.; Miller, J. K.

2017-12-01

Munitions and explosives of concern (MEC) are present in U.S. waters as a result of past and ongoing live-fire testing and training, combat operations, and sea disposal. To identify MEC that may pose a risk to human safety during development of offshore wind facilities on the Atlantic Outer Continental Shelf (OCS), the Bureau of Ocean Energy Management (BOEM) is preparing to develop guidance on risk analysis and selection processes for methods and technologies to identify MEC in Wind Energy Areas (WEA). This study developed a process for selecting appropriate technologies and methodologies for MEC detection using a synthesis of historical research, physical site characterization, remote sensing technology review, and in-field trials. Personnel were tasked with seeding a portion of the Delaware WEA with munitions surrogates, while a second group of researchers not privy to the surrogate locations tested and optimized the selected methodology to find and identify the placed targets. This in-field trial, conducted in July 2016, emphasized the use of multiple sensors for MEC detection, and led to further guidance for future MEC detection efforts on the Atlantic OCS. An April 2017 follow on study determined the fate of the munitions surrogates after the Atlantic storm season had passed. Using regional hydrodynamic models and incorporating the recommendations from the 2016 field trial, the follow on study examined the fate of the MEC and compared the findings to existing research on munitions mobility, as well as models developed as part of the Office of Naval Research Mine-Burial Program. Focus was given to characterizing the influence of sediment type on surrogate munitions behavior and the influence of mophodynamics and object burial on MEC detection. Supporting Mine-Burial models, ripple bedforms were observed to impede surrogate scour and burial in coarse sediments, while surrogate burial was both predicted and observed in finer sediments. Further, incorporation of

Geopolymerisation of silt generated from construction and demolition waste washing plants.

Science.gov (United States)

Lampris, C; Lupo, R; Cheeseman, C R

2009-01-01

Recycling plants that size, sort and wash construction and demolition waste can produce high quality aggregate. However, they also produce up to 80ton per hour of filter cake waste containing fine (waste and normally landfilled. This research investigated the potential to form geopolymers containing silt, which would allow this problematic waste to be beneficially reused as aggregate. This would significantly improve the economic viability of recycling plants that wash wastes. Silt filter cakes have been collected from a number of aggregate washing plants operating in the UK. These were found to contain similar aluminosilicate crystalline phases. Geopolymer samples were produced using silt and silt mixed with either metakaolin or pulverised fuel ash (PFA). Silt geopolymers cured at room temperature had average 7-day compressive strengths of 18.7MPa, while partial substitution of silt by metakaolin or PFA increased average compressive strengths to 30.5 and 21.9MPa, respectively. Curing specimens for 24h at 105 degrees C resulted in a compressive strength of 39.7MPa and microstructural analysis confirmed the formation of dense materials. These strengths are in excess of those required for materials to be used as aggregate, particularly in unbound applications. The implications of this research for the management of waste silt at construction and demolition waste washing plants are discussed.

Recycled construction and demolition concrete waste as aggregate for structural concrete

Directory of Open Access Journals (Sweden)

Ashraf M. Wagih

2013-12-01

Full Text Available In major Egyptian cities there is a surge in construction and demolition waste (CDW quantities causing an adverse effect on the environment. The use of such waste as recycled aggregate in concrete can be useful for both environmental and economical aspects in the construction industry. This study discusses the possibility to replace natural coarse aggregate (NA with recycled concrete aggregate (RCA in structural concrete. An investigation into the properties of RCA is made using crushing and grading of concrete rubble collected from different demolition sites and landfill locations around Cairo. Aggregates used in the study were: natural sand, dolomite and crushed concretes obtained from different sources. A total of 50 concrete mixes forming eight groups were cast. Groups were designed to study the effect of recycled coarse aggregates quality/content, cement dosage, use of superplasticizer and silica fume. Tests were carried out for: compressive strength, splitting strength and elastic modulus. The results showed that the concrete rubble could be transformed into useful recycled aggregate and used in concrete production with properties suitable for most structural concrete applications in Egypt. A significant reduction in the properties of recycled aggregate concrete (RAC made of 100% RCA was seen when compared to natural aggregate concrete (NAC, while the properties of RAC made of a blend of 75% NA and 25% RCA showed no significant change in concrete properties.

Acoustic and vibrational tests of effects induced on building by the demolition of the 'Ponte del Barco' Firenze - Toscana

International Nuclear Information System (INIS)

Stragapede, Francesco; Biannucci, Roberto; Pascini, Lando Umberto; Leonasi, Giovanni

2016-01-01

For demolition of Ponte del Barco, the Torrente Mugnone overpass at the Parco delle Cascine of Firenze, were checked up entities in the field of energy and vibrational noise produced during activities on sensitive lens, considering the building located near the structure being demolished. The vibrations to the building have been checked with reference to noise thresholds of disturbance to the person (UNI 9614) and resentment/damage to the building (UNI 9 9 16). Evaluation of transient vibration actions on the building were examined during the demolition of the structure, carried out using excavator CAT 320 D LN equipped with concrete crusher, and handling stages of demolition material using excavator ZAX 2 40 Hitachi equipped with a shovel. The tests were conducted with Symphonie type level meter (class 1 REF. EN60651/94 and EN60804/9 4) and oriented velocimeters n. 4 recording stations using GEOBOX of Sara Electr. Instr. The noise level was compared with the acoustic limits of the area and the intensity of vibration induced on sensitive building was related to thresholds of disturbance to the person and damage to structures, ensuring that in the course of the demolition operations were the conditions of security of operators in the area and the absence of damage to the buildings. Based on the findings from the analysis, the acoustic activity of demolition of the Bridge in Florence took place within the acoustic limits of exemption of localization activities (class IV – area of intense human activity). The exceeded the thresholds of vibrational disturbance to the person was checked, in reference UNI 9614; the exceeded the thresholds for structural damage was not checked, in reference to UNI 9916. The attendance of the necessary staff for testing acoustic and vibrational did not affect any sensitive subject even in the presence of the excess of noise and vibration thresholds of disturbance to the person.

Recycling of construction and demolition waste in Kuwait

International Nuclear Information System (INIS)

Kartam, N.; Al-Mutairi, N.; Al-Ghusain, I.; Al-Humoud, J.

2002-01-01

'Full text:' There is an increasing pressure on the construction industry to reduce costs and improve our environment. The fact is that both of these goals can be achieved at the same time. Although construction and demolition (C and D) constitutes a major type of waste in terms of volume and weight, its management and recycling efforts have not seen the light in Kuwait. The goal of this research project is to study methods leading to the minimization of the total C and D waste that is landfilled in Kuwait. This can be achieved by applying the waste management hierarchy in order of importance: 1) reduce, 2) re-use, 3) recycle, 4) incineration (energy recovery), and 5) safe disposal. This paper presents the current C and D waste disposal system in Kuwait and identifies potential problems to the environment, people and economy. Then, it investigates the recycling option to manage and control this major type of waste in an economically efficient and environmentally safe manner. There are significant volumes of potentially valuable and recoverable resources being wasted in the construction industry, and these figures are continuously growing as we are starting the new millennium. C and D waste constitutes 15%-30% of all solid waste entering landfills in various countries [Bossink 1995]; and thus it is a major type of waste. An estimated 2-3 million ton of construction and demolition waste are being only disposed of in Kuwait's landfill sites each year despite the limited available land (Industrial Investment Company, 1990). C and D waste is a target because it is both heavy and bulky, and therefore undesirable for disposal in engineered, lined landfills because of the space it consumes. On the other hand, many C and D materials have high potential for recovery and use. Recovering C and D waste can help communities reach their recycling goals, preserve valuable space in their local landfills, and create better opportunities for handling other kind of waste. Therefore

78 FR 29648 - Regulated Navigation Area; Waldo-Hancock Bridge Demolition, Penobscot River, Between Prospect and...

Science.gov (United States)

2013-05-21

... 1625-AA11 Regulated Navigation Area; Waldo-Hancock Bridge Demolition, Penobscot River, Between Prospect... River between Prospect and Verona, ME, under and surrounding the Waldo- Hancock Bridge in order to... Prospect and Verona, ME. (a) Location. The following area is a Regulated Navigation Area (RNA): All...

Screening Level Ecological Risk Assessments of Some Military Munitions and Obscurant-related Compounds for Selected Threatened and Endangered Species

National Research Council Canada - National Science Library

Von Stackleberg, Katherine; Amos, Craig; Butler, C; Smith, Thomas; Famely, J; McArdle, M; Southworth, B; Steevens, Jeffrey

2006-01-01

...) associated with munitions. This study evaluates the potential long-term impacts on selected threatened and endangered species resulting from dispersion and deposition of vapors and particles found in the fog oils...

Validation of Passive Sampling Devices for Monitoring of Munitions Constituents in Underwater Environments

Science.gov (United States)

2017-09-01

and explosives of concern (MEC) corroding, breaching, and leaking MC into the water column (Darrach, Chutjian, and Plett, 1998; GMI, 2007; Lewis et...underwater UWMM have the potential to corrode, breach, and leak munitions constituents (MCs) such as 2,4,6-trinitrotoluene (TNT) and hexahydro-1,3,5...Wang et al., 2013), a number of challenges prevent accurate assessment of environmental exposure using traditional water , sediment, and tissue

Decommissioning and demolition of the Greifswald nuclear power station

International Nuclear Information System (INIS)

Sterner, H.; Leushacke, D.; Rittscher, D.

1995-01-01

The unexpected decision to decommission the plants in Greifswald makes the management and disposal of fuels and plant waste a major issue to be solved as a precondition for decommissioning and dismantling. The decisive point in waste management is the existence of an interim store or repository of sufficient capacity to accept both the nuclear fuel and the plant waste and the considerable volumes of radioactive residues arising in dismantling. Current major activities include planning for decommissioning and demolition, and drafting of the licensing documents; removal of the fuel elements from the reactor units; construction of the northern interim store for fuel elements and residues. (orig./HP)

Estimating construction and demolition debris generation using a materials flow analysis approach.

Science.gov (United States)

Cochran, K M; Townsend, T G

2010-11-01

The magnitude and composition of a region's construction and demolition (C&D) debris should be understood when developing rules, policies and strategies for managing this segment of the solid waste stream. In the US, several national estimates have been conducted using a weight-per-construction-area approximation; national estimates using alternative procedures such as those used for other segments of the solid waste stream have not been reported for C&D debris. This paper presents an evaluation of a materials flow analysis (MFA) approach for estimating C&D debris generation and composition for a large region (the US). The consumption of construction materials in the US and typical waste factors used for construction materials purchasing were used to estimate the mass of solid waste generated as a result of construction activities. Debris from demolition activities was predicted from various historical construction materials consumption data and estimates of average service lives of the materials. The MFA approach estimated that approximately 610-78 × 10(6)Mg of C&D debris was generated in 2002. This predicted mass exceeds previous estimates using other C&D debris predictive methodologies and reflects the large waste stream that exists. Copyright © 2010 Elsevier Ltd. All rights reserved.

Post-traumatic stress disorder in adult victims of cluster munitions in Lebanon: a 10-year longitudinal study.

Science.gov (United States)

Fares, Jawad; Gebeily, Souheil; Saad, Mohamad; Harati, Hayat; Nabha, Sanaa; Said, Najwane; Kanso, Mohamad; Abdel Rassoul, Ronza; Fares, Youssef

2017-08-18

This study aims to explore the short-term and long-term prevalence and effects of post-traumatic stress disorder (PTSD) among victims of cluster munitions. A prospective 10-year longitudinal study that took place in Lebanon. Two-hundred-and-forty-four Lebanese civilian victims of submunition blasts, who were injured in 2006 and were over 18 years old, were interviewed. Included were participants who had been diagnosed with PTSD according to the Diagnostic and Statistical Manual of Mental Disorders, 5th Edition (DSM-5) and the PTSD Checklist - Civilian Version in 2006. Interviewees were present for the 10-year follow-up. PTSD prevalence rates of participants in 2006 and 2016 were compared. Analysis of the demographical data pertaining to the association of long-term PTSD with other variables was performed. p Values <0.05 were considered statistically significant for all analyses (95% CI). All the 244 civilians injured by cluster munitions in 2006 responded, and were present for long-term follow-up in 2016. The prevalence of PTSD decreased significantly from 98% to 43% after 10 years (p<0.001). A lower long-term prevalence was significantly associated with male sex (p<0.001), family support (p<0.001) and religion (p<0.001). Hospitalisation (p=0.005) and severe functional impairment (p<0.001) post-trauma were significantly associated with increased prevalence of long-term PTSD. Symptoms of negative cognition and mood were more common in the long run. In addition, job instability was the most frequent socioeconomic repercussion among the participants (88%). Psychological symptoms, especially PTSD, remain high in war-affected populations many years after the war; this is particularly evident for Lebanese civilians who were victimised by cluster munitions. Screening programmes and psychological interventions need to be implemented in vulnerable populations exposed to war traumas. Officials and public health advocates should consider the socioeconomic implications, and

Demolition to Green-Field conditions of the FRJ-1 (MERLIN) research reactor. Successes and hurdles in the demolition of a research reactor of the megawatt class; Der Rueckbau des Forschungsreaktors FRJ-1 (MERLIN) bis zur 'Gruenen Wiese'. Erfolge und Huerden beim Rueckbau eines Forschungsreaktors der Megawatt-Klasse

Energy Technology Data Exchange (ETDEWEB)

Stahn, Burkhard; Printz, Rudolf; Matela, Karel; Zehbe, Carsten; Stauch, Bernhard; Zander, Iven [Forschungszentrum Juelich GmbH, Juelich (Germany)

2010-02-15

The Juelich-1 Research Reactor (FRJ-1), also referred to as MERLIN (Medium Energy Research Light Water Moderated Industrial Nuclear Reactor), was a light-water moderated and cooled swimming pool reactor of British design. The cornerstone in the erection of the reactor building was laid on June 11, 1958. Reactor operation was started on February 23, 1962. The plant was last run at a thermal power of 10 MW and shut down for good in 1985 after 23 years of operation. After the fuel elements had been removed and most of the experimental installations dismantled, some first steps towards demolition were taken in 1995. Demolition on a large scale began in 1996. September 8, 2008 was a special day: On the area of the former reactor hall, an oak tree was planted as a symbol of the 'green field' and of the original oak wood which had to make way for the construction of reactors in Juelich. An oak tree now stands in the place of the reactor unit. Was that all? It was not, for there were ancillary systems, operations, utility and hygiene buildings which had to be pulled down. Decontamination and clearance measurements were completed. The application for clearance was prepared and completed. Conventional demolition was started in 2009. After completion of that step, the last chapter about demolition of the FRJ-1 research reactor has been written, and the book can be closed. (orig.)

Immobilization of calcium sulfate contained in demolition waste

International Nuclear Information System (INIS)

Ambroise, J.; Pera, J.

2008-01-01

This paper presents the results of a laboratory study undertaken to examine the treatment of demolition waste containing calcium sulfate by means of calcium sulfoaluminate clinker (CSA). The quantity of CSA necessary to entirely consume calcium sulfate was determined. Using infrared spectrometry analysis and X-ray diffraction, it was shown that calcium sulfate was entirely consumed when the ratio between CSA and calcium sulfate was 4. Standard sand was polluted by 4% calcium sulfate. Two solutions were investigated: ·either global treatment of sand by CSA, ·or immobilization of calcium sulfate by CSA, followed by the introduction of this milled mixture in standard sand. Regardless of the type of treatment, swelling was almost stabilized after 28 days of immersion in water

Thermal resistance and conductivity of recycled construction and demolition waste (RCDW concrete blocks

Directory of Open Access Journals (Sweden)

Ivan Julio Apolonio Callejas

Full Text Available Abstract In Brazil, studies to reuse construction and demolition waste are a special issue because a large amount of this material has been delivered to the public landfills and in illegal places. Some researchers have suggested reusing this material in building elements, such as bricks or blocks. It is possible to find a lot of researches in physical/mechanical characterization, while little effort has been made to characterize recycled construction and demolition waste blocks (RCDW for their thermal properties. The aim of this work was to characterize the RCDW thermal resistance and conductivity in order to provide subsidies for a building's thermal performance analysis. The hot-box method was adapted, together with measuring techniques with a heat-flow meter to determine the RCDW thermal properties. The results indicated that the RCDW block overall thermal resistance and thermal conductivity in the solid region was within the intervals of 0.33≤RT≤0.41m2KW-1 and 0.60≤l≤0.78Wm-1K-1, respectively. The lower resistance and conductivity values are justified by the presence of aggregate with a lower density and lower thermal conductivity than the natural aggregate.

An integrated theoretical and experimental investigation of insensitive munition compounds adsorption on cellulose, cellulose triacetate, chitin and chitosan surfaces.

Science.gov (United States)

Gurtowski, Luke A; Griggs, Chris S; Gude, Veera G; Shukla, Manoj K

2018-02-01

This manuscript reports results of combined computational chemistry and batch adsorption investigation of insensitive munition compounds, 2,4-dinitroanisole (DNAN), triaminotrinitrobenzene (TATB), 1,1-diamino-2,2-dinitroethene (FOX-7) and nitroguanidine (NQ), and traditional munition compound 2,4,6-trinitrotoluene (TNT) on the surfaces of cellulose, cellulose triacetate, chitin and chitosan biopolymers. Cellulose, cellulose triacetate, chitin and chitosan were modeled as trimeric form of the linear chain of 4 C 1 chair conformation of β-d-glucopyranos, its triacetate form, β-N-acetylglucosamine and D-glucosamine, respectively, in the 1➔4 linkage. Geometries were optimized at the M062X functional level of the density functional theory (DFT) using the 6-31G(d,p) basis set in the gas phase and in the bulk water solution using the conductor-like polarizable continuum model (CPCM) approach. The nature of potential energy surfaces of the optimized geometries were ascertained through the harmonic vibrational frequency analysis. The basis set superposition error (BSSE) corrected interaction energies were obtained using the 6-311G(d,p) basis set at the same theoretical level. The computed BSSE in the gas phase was used to correct interaction energy in the bulk water solution. Computed and experimental results regarding the ability of considered surfaces in adsorbing the insensitive munitions compounds are discussed. Copyright © 2017. Published by Elsevier B.V.

Applicability of LCA tool for building materials produced from construction and demolition waste : case of Tanzania

NARCIS (Netherlands)

Sabai, M.M.; Egmond - de Wilde De Ligny, van E.L.C.; Cox, M.G.D.M.; Mato, R.R.A.M.; Lichtenberg, J.J.N.

2009-01-01

It is estimated that about 10 million tonnes of construction and demolition (C&D) waste is generated annually in Tanzania. This waste is expected to increase even more because of population increases, urbanization, industrialization and commercialization which results in more utilization of natural

In-Flight Self-Alignment Method Aided by Geomagnetism for Moving Basement of Guided Munitions

Directory of Open Access Journals (Sweden)

Shuang-biao Zhang

2015-01-01

Full Text Available Due to power-after-launch mode of guided munitions of high rolling speed, initial attitude of munitions cannot be determined accurately, and this makes it difficult for navigation and control system to work effectively and validly. An in-flight self-alignment method aided by geomagnetism that includes a fast in-flight coarse alignment method and an in-flight alignment model based on Kalman theory is proposed in this paper. Firstly a fast in-flight coarse alignment method is developed by using gyros, magnetic sensors, and trajectory angles. Then, an in-flight alignment model is derived by investigation of the measurement errors and attitude errors, which regards attitude errors as state variables and geomagnetic components in navigation frame as observed variables. Finally, fight data of a spinning projectile is used to verify the performance of the in-flight self-alignment method. The satisfying results show that (1 the precision of coarse alignment can attain below 5°; (2 the attitude errors by in-flight alignment model converge to 24′ at early of the latter half of the flight; (3 the in-flight alignment model based on Kalman theory has better adaptability, and show satisfying performance.

Properties of Concrete Paving Blocks and Hollow Tiles with Recycled Aggregate from Construction and Demolition Wastes

Directory of Open Access Journals (Sweden)

Carlos Rodríguez

2017-11-01

Full Text Available In recent years there has been an increasing tendency to recycle the wastes generated by building companies in the construction industry, demolition wastes being the most important in terms of volume. The aim of this work is to study the possibility of using recycled aggregates from construction and demolition wastes in the preparation of precast non-structural concretes. To that purpose, two different percentages (15% and 30% of natural aggregates were substituted by recycled aggregates in the manufacture of paving blocks and hollow tiles. Dosages used by the company have not been changed by the introduction of recycled aggregate. Precast elements have been tested by means of compressive and flexural strength, water absorption, density, abrasion, and slipping resistance. The results obtained show the possibility of using these wastes at an industrial scale, satisfying the requirements of the Spanish standards for these elements.

Penetrating injury to the chest by an attenuated energy projectile: a case report and literature review of thoracic injuries caused by "less-lethal" munitions.

Science.gov (United States)

Rezende-Neto, Joao; Silva, Fabriccio Df; Porto, Leonardo Bo; Teixeira, Luiz C; Tien, Homer; Rizoli, Sandro B

2009-06-26

We present the case of a patient who sustained a penetrating injury to the chest caused by an attenuated energy rubber bullet and review the literature on thoracic injuries caused by plastic and rubber "less-lethal" munitions. The patient of this report underwent a right thoracotomy to extract the projectile as well as a wedge resection of the injured lung parenchyma. This case demonstrates that even supposedly safe riot control munition fired at close range, at the torso, can provoke serious injury. Therefore a thorough investigation and close clinical supervision are justified.

Investigation of combined effect of mixture variables on mechanical properties of cement treated demolition waste

NARCIS (Netherlands)

Xuan, D.; Houben, L.J.M.; Molenaar, A.A.A.; Shui, Z.

2012-01-01

One of high efficient ways to reuse the recycled construction and demolition waste (CDW) is to consider it as a road base material. The recycled CDW however is mainly a mix of recycled masonry and concrete with a wide variation in composition. This results that the mechanical properties of cement

Sampling and Analysis Instruction for the Demolition of the Masonry Block for the 108-F Biological Laboratory

International Nuclear Information System (INIS)

Byrnes, M. E.

1999-01-01

This sampling and analysis instruction (SAI) has been prepared to clearly define the sampling and analysis activities to be performed in support of the demolition and disposition (or disposal) of the 108-F Biological Laboratory masonry block walls

Construction and demolition waste: Comparison of standard up-flow column and down-flow lysimeter leaching tests

DEFF Research Database (Denmark)

Butera, Stefania; Hyks, Jiri; Christensen, Thomas Højlund

2015-01-01

Five samples of construction and demolition waste (C&DW) were investigated in order to quantify leaching of inorganic elements under percolation conditions according to two different experimental setups: standardised up-flow saturated columns (-1TS) for Al, As, Ba, Cd, Cu, DOC, Mg, Mn, Ni, P, Pb...

Tracking and Interception of Ground-Based RF Sources Using Autonomous Guided Munitions with Passive Bearings-Only Sensors and Tracking Algorithms

National Research Council Canada - National Science Library

Ezal, Kenan; Agate, Craig

2006-01-01

This paper considers the problem of tracking and intercepting a potentially moving ground-based RF source with an autonomous guided munition that has a passive bearings-only sensor located on its nose...

An Estimation of Construction and Demolition Debris in Seoul, Korea: Waste Amount, Type, and Estimating Model.

Science.gov (United States)

Seo, Seongwon; Hwang, Yongwoo

1999-08-01

Construction and demolition (C&D) debris is generated at the site of various construction activities. However, the amount of the debris is usually so large that it is necessary to estimate the amount of C&D debris as accurately as possible for effective waste management and control in urban areas. In this paper, an effective estimation method using a statistical model was proposed. The estimation process was composed of five steps: estimation of the life span of buildings; estimation of the floor area of buildings to be constructed and demolished; calculation of individual intensity units of C&D debris; and estimation of the future C&D debris production. This method was also applied in the city of Seoul as an actual case, and the estimated amount of C&D debris in Seoul in 2021 was approximately 24 million tons. Of this total amount, 98% was generated by demolition, and the main components of debris were concrete and brick.

Study on the blasting demolition of steel construction. Part 2. Demolition work of steel tower; Tekkotsu kozobutsu no bakuha kaitai ni kansuru kenkyu. 2. Koro yagura happa kaitai koji

Energy Technology Data Exchange (ETDEWEB)

Ogata, Y.; Wada, Y.; Katsuyama, K. [National Institute for Resources and Environment, Tsukuba (Japan); Nishida, T.; Hoshino, M.; Nagano, M. [Kacoh Co. Ltd., Tokyo (Japan)

1997-06-30

This paper describes the blasting demolition of steel tower of iron works. The steel tower had four columns, and its dimension was 17 mtimes17 m in cross section and 77.6 m height. The total weight was about 1,724 t. The 18.4 kg V-type linear shaped charge was fixed around columns with box weld structures, and initiated using 16 seismograph electric detonators. Vibration and noise were measured during blasting and collapse of the tower. In the both case, the vibration levels were between 67 and 71 dB, which were low and under 75 dB, the standard level during specific construction works of the regulation act of vibration. The noise level was 120 dB(A) at the point 200 m away from the blasting source, which was over 85 dB(A), the standard level. The collapse process of steel tower was simulated using discontinuous deformation analysis. The results agreed well with those from the actual collapse. The steel tower landed about 6 seconds after the initiation, and it took about 15 seconds to complete the collapse. Before the demolition, the 6 t parts of forefeet of two columns in the collapse direction were cut and removed by blasting. Thus, the collapse was controlled in the given direction. 5 refs., 13 figs., 2 tabs.

Composition and leaching of construction and demolition waste: inorganic elements and organic compounds.

Science.gov (United States)

Butera, Stefania; Christensen, Thomas H; Astrup, Thomas F

2014-07-15

Thirty-three samples of construction and demolition waste collected at 11 recycling facilities in Denmark were characterised in terms of total content and leaching of inorganic elements and presence of the persistent organic pollutants PCBs and PAHs. Samples included (i) "clean" (i.e. unmixed) concrete waste, (ii) mixed masonry and concrete, (iii) asphalt and (iv) freshly cast concrete cores; both old and newly generated construction and demolition waste was included. PCBs and PAHs were detected in all samples, generally in non-critical concentrations. Overall, PAHs were comparable to background levels in urban environments. "Old" and "new" concrete samples indicated different PCB congener profiles and the presence of PCB even in new concrete suggested that background levels in raw materials may be an issue. Significant variability in total content of trace elements, even more pronounced for leaching, was observed indicating that the number of analysed samples may be critical in relation to decisions regarding management and utilisation of the materials. Higher leaching of chromium, sulphate and chloride were observed for masonry-containing and partly carbonated samples, indicating that source segregation and management practices may be important. Generally, leaching was in compliance with available leaching limits, except for selenium, and in some cases chromium, sulphate and antimony. Copyright © 2014 Elsevier B.V. All rights reserved.

Penetrating injury to the chest by an attenuated energy projectile: a case report and literature review of thoracic injuries caused by "less-lethal" munitions

Directory of Open Access Journals (Sweden)

Porto Leonardo BO

2009-06-01

Full Text Available Abstract We present the case of a patient who sustained a penetrating injury to the chest caused by an attenuated energy rubber bullet and review the literature on thoracic injuries caused by plastic and rubber "less-lethal" munitions. The patient of this report underwent a right thoracotomy to extract the projectile as well as a wedge resection of the injured lung parenchyma. This case demonstrates that even supposedly safe riot control munition fired at close range, at the torso, can provoke serious injury. Therefore a thorough investigation and close clinical supervision are justified.

A Quantum Non-Demolition Parity measurement in a mixed-species trapped-ion quantum processor

Science.gov (United States)

Marinelli, Matteo; Negnevitsky, Vlad; Lo, Hsiang-Yu; Flühmann, Christa; Mehta, Karan; Home, Jonathan

2017-04-01

Quantum non-demolition measurements of multi-qubit systems are an important tool in quantum information processing, in particular for syndrome extraction in quantum error correction. We have recently demonstrated a protocol for quantum non-demolition measurement of the parity of two beryllium ions by detection of a co-trapped calcium ion. The measurement requires a sequence of quantum gates between the three ions, using mixed-species gates between beryllium hyperfine qubits and a calcium optical qubit. Our work takes place in a multi-zone segmented trap setup in which we have demonstrated high fidelity control of both species and multi-well ion shuttling. The advantage of using two species of ion is that we can individually manipulate and read out the state of each ion species without disturbing the internal state of the other. The methods demonstrated here can be used for quantum error correcting codes as well as quantum metrology and are key ingredients for realizing a hybrid universal quantum computer based on trapped ions. Mixed-species control may also enable the investigation of new avenues in quantum simulation and quantum state control. left the group and working in a company now.

Technology Assessment of Dust Suppression Techniques Applied During Structural Demolition. Topical Report August1, 1995 - October 30, 1996

International Nuclear Information System (INIS)

Boudreaux, J.F.; Ebadian, M.A.; Williams, P.T.; Dua, S.K.

1998-01-01

Hanford, Fernald, Savannah River, and other sites are currently reviewing technologies that can be implemented to demolish buildings in a cost-effective manner. In order to demolish a structure properly and, at the same time, minimize the amount of dust generated from a given technology, an evaluation must be conducted to choose the most appropriate dust suppression technology given site-specific conditions. Thus, the purpose of this research, which was carried out at the Hemispheric Center for Environmental Technology (HCET) at Florida International University, was to conduct an experimental study of dust aerosol abatement (dust suppression) methods as applied to nuclear D and D. This experimental study targeted the problem of dust suppression during the demolition of nuclear facilities. The resulting data were employed to assist in the development of mathematical correlations that can be applied to predict dust generation during structural demolition

The health hazards of depleted uranium munitions. Part 1

International Nuclear Information System (INIS)

2001-01-01

Depleted uranium is a toxic and weakly radioactive metal used for a variety of purposes. Perhaps its most controversial use is in battlefield munitions, where it can be widely dispersed in the form of fine particles and shrapnel that may enter the bodies of combatants and others through inhalation, ingestion or wounding. It is a matter of legitimate public concern whether the use of this material in this way could create unacceptable health hazards or damage to the environment. The objective of our study has been to provide the best scientific understanding of the ways in which the material may be distributed, how it may be taken up by humans, and the potential implications for health. For politicians, any hazards to health have to be balanced against the military advantages that the use of these munitions confers. We have not tried to reach a judgment on these political issues, but we believe that a better scientific understanding of the extent of the hazards will make it easier for these wider questions to be addressed in a more objective way. This report is the first of two, and addresses the likely levels of exposure to depleted uranium, the resulting radiological risks, and the lessons to be learned from epidemiological studies. Our second report will address toxicological risks and environmental issues. So far, we conclude that risks from radiation are low for most soldiers on the battlefield, and for civilians who later return to the area. However, there are uncertainties about the maximal levels of exposure to depleted uranium on the battlefield, and there may be circumstances in which a few soldiers are exposed to levels of depleted uranium that result in a significant risk to health. Further studies are needed to determine the levels of exposure to depleted uranium that might occur on the battlefield and to judge whether such higher risks are likely to occur in practice

Methodology to Estimate the Quantity, Composition, and Management of Construction and Demolition Debris in the United States

Science.gov (United States)

This report, Methodology to Estimate the Quantity, Composition and Management of Construction and Demolition Debris in the US, was developed to expand access to data on CDD in the US and to support research on CDD and sustainable materials management. Since past US EPA CDD estima...

Bioinspired polarization navigation sensor for autonomous munitions systems

Science.gov (United States)

Giakos, G. C.; Quang, T.; Farrahi, T.; Deshpande, A.; Narayan, C.; Shrestha, S.; Li, Y.; Agarwal, M.

2013-05-01

Small unmanned aerial vehicles UAVs (SUAVs), micro air vehicles (MAVs), Automated Target Recognition (ATR), and munitions guidance, require extreme operational agility and robustness which can be partially offset by efficient bioinspired imaging sensor designs capable to provide enhanced guidance, navigation and control capabilities (GNC). Bioinspired-based imaging technology can be proved useful either for long-distance surveillance of targets in a cluttered environment, or at close distances limited by space surroundings and obstructions. The purpose of this study is to explore the phenomenology of image formation by different insect eye architectures, which would directly benefit the areas of defense and security, on the following four distinct areas: a) fabrication of the bioinspired sensor b) optical architecture, c) topology, and d) artificial intelligence. The outcome of this study indicates that bioinspired imaging can impact the areas of defense and security significantly by dedicated designs fitting into different combat scenarios and applications.

Operation Iraqi Freedom: DOD Should Apply Lessons Learned Concerning the Need for Security over Conventional Munitions Storage Sites to Future Operations Planning

National Research Council Canada - National Science Library

D'Agostino, Davi M

2007-01-01

The Government Accountability Office (GAO) is releasing a report today on lessons learned concerning the need for security over conventional munitions storage sites that provides the basis for this testimony...

Solar One demolition and remediation

International Nuclear Information System (INIS)

Wallace, G.L.

1995-01-01

Solar One was designed to demonstrate the feasibility of generating electrical energy from solar power using a central receiver concept. An array of heliostats focused sunlight onto a central receiver, which superheated water to produce steam. Although Solar One was successful, the oil-based Thermal Storage System (TSS), used to store heat energy for power generation at night, was not efficient. When the TSS was demolished for the installation of a more efficient molten salt system, a major effort was made to salvage or recycle all of its equipment and materials. During TSS demolition, approximately 7 tons of aluminum shielding and 205 tons of steel were salvaged as scrap metal; 200 tons of concrete was used for erosion protection along the Mohave River banks; 150,000 gallons of oil was recycled and 100 tons of equipment was salvaged for use at other facilities. During remediation, approximately 9,000 tons of oil contaminated sand, gravel and soil was recycled into approximately 10,000 tons of asphalt concrete and used to pave a nearby 5-acre parking lot at Barstow College. This not only reduced project remediation costs, but also met environmental requirements and provided a much needed community service. Of the estimated 11,864 tons of equipment and material from the TSS, less than 1% was disposed of at a landfill

Life cycle assessment of construction and demolition waste management

DEFF Research Database (Denmark)

Butera, Stefania; Christensen, Thomas Højlund; Astrup, Thomas Fruergaard

2015-01-01

Life cycle assessment (LCA) modelling of construction and demolition waste (C&DW) management was carried out. The functional unit was management of 1 Mg mineral, source separated C&DW, which is either utilised in road construction as a substitute for natural aggregates, or landfilled. The assessed...... of the use of C&DW. Typical uncertainties related to contaminant leaching were addressed. For most impact categories, utilisation of C&DW in road construction was preferable to landfilling; however, for most categories, utilisation resulted in net environmental burdens. Transportation represented the most...... of the impact assessment was critical for modelling the leaching impacts. Compared with the overall life cycle of building and construction materials, leaching emissions were shown to be potentially significant for toxicity impacts, compared with contributions from production of the same materials, showing...

Streamlining of the Decontamination and Demolition Document Preparation Process

International Nuclear Information System (INIS)

Durand, Nick; Meincke, Carol; Peek, Georgianne

1999-01-01

During the past five years, the Sandia National Labo- ratories Decontamination, Decommissioning, Demolition, and Reuse (D3R) Program has evolved and become more focused and efficient. Historical approaches to project documentation, requirements, and drivers are discussed detailing key assumptions, oversight authority, and proj- ect approvals. Discussion of efforts to streamline the D3R project planning and preparation process include the in- corporation of the principles of graded approach, Total Quality Management, and the Observational Method (CH2MHILL April 1989).1 Process improvements were realized by clearly defining regulatory requirements for each phase of a project, establishing general guidance for the program and combining project-specific documents to eliminate redundant and unneeded information. Proc- ess improvements to cost, schedule, and quality are dis- cussed in detail for several projects

The Ellweiler uranium plant - a demolition and recycling project

International Nuclear Information System (INIS)

Mika, S.; Rohr, T.; Seehars, R.; Feser, A.

1999-01-01

The uranium plant at Ellweiler, district of Birkenfeld, was used for the production and storage of uranium concentrates. The owner of the Ellweiler uranium plant (UAE), Gewerkschaft Brunhilde GmbH, ceased processing uranium ore and recycling in 1989 and has been in liquidation since September 1991. The State of Rhineland-Palatinate, had safety measures adopted in a first step, getting the plant into a safe state by former plant personnel. The entire plant was demolished in a second step. The contract for demolishing the former uranium plant was awarded to ABB Reaktor as the general contractor in August 1996. Demolition work was carried out between April 1997 and May 1999. A total of approx. 7900 Mg of material was disposed of. At present, recultivation measures are being carried out. (orig.) [de

Data Gap Analysis and Damage Case Studies: Risk Analyses from Construction and Demolition Debris Landfills and Recycling Facilities

Science.gov (United States)

The report presents an evaluation of construction and demolition (C&D) debris management in the US to update and expand upon the previous set of data to include information on more recent cases of damage and potential impacts and expand the breadth of damages beyond groundwater a...

Contact arc metal cutting (CAMC), a young cutting technique has matured. Successful use under water in the demolition of the Karlsruhe multipurpose research reactor (MFZR)

International Nuclear Information System (INIS)

Stanke, D.; Bienia, H.; Loeb, A.; Thoma, M.; Eisenmann, B.; Prechtl, E.; Suessdorf, W.; Kremer, G.; Ruemenapp, T.

2006-01-01

Dismantling radiologically burdened large components is among the most complex and difficult jobs in the demolition of nuclear installations. The technologies used and their safe operation play a key role in demolition. Dismantling highly activated components as a rule requires shielding by water. As a consequence, the techniques employed must be designed for use under water. A variety of technologies are available for these applications. One established mechanical cutting method is water abrasive suspension jet cutting (WASS). Because of the small cutting nozzle employed, this highly flexible cutting technique can be used nearly anywhere together with different guiding systems. In the course of disassembly under water of the MZFR, plasma cutting has been found to be a reliable and efficient technique for remote operation. Contact arc metal cutting is a thermal cutting technique allowing all electrically conducting materials, including those with claddings, to be cut nearly irrespective of their component geometries. The methods, technology, possible uses, and practical operation of contact arc metal cutting in the demolition of the MZFR are covered in this article. (orig.)

Forecasting of construction and demolition waste in Brazil.

Science.gov (United States)

Paz, Diogo Hf; Lafayette, Kalinny Pv

2016-08-01

The objective of this article is to develop a computerised tool (software) that facilitates the analysis of strategies for waste management on construction sites through the use of indicators of construction and demolition waste generation. The development involved the following steps: knowledge acquisition, structuring the system, coding and system evaluation. The step of knowledge acquisition aims to provide subsidies for the representation of them through models. In the step of structuring the system, it was presented the structuring and formalisation of knowledge for the development of the system, and has two stages: the construction of the conceptual model and the subsequent instantiation of the model. The coding system aims to implement (code) the conceptual model developed in a model played by computer (digital). The results showed that the system is very useful and applicable in construction sites, helping to improve the quality of waste management, and creating a database that will support new research. © The Author(s) 2016.

41 CFR 102-75.170 - What happens to the related personal property in a structure scheduled for demolition?

Science.gov (United States)

2010-07-01

... consideration should be given to designating items having possible historical or artistic value as personal... related personal property in a structure scheduled for demolition? 102-75.170 Section 102-75.170 Public... As Personal Property § 102-75.170 What happens to the related personal property in a structure...

Photochemical transformation of the insensitive munitions compound 2,4-dinitroanisole

Energy Technology Data Exchange (ETDEWEB)

Rao, Balaji, E-mail: anandharaob@ornl.gov [Environmental Sciences Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Wang, Wei [Environmental Sciences Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Cai, Qingsong; Anderson, Todd [Department of Environmental Toxicology, The Institute of Environment and Human Health, Texas Tech University, Lubbock, TX (United States); Gu, Baohua, E-mail: gub1@ornl.gov [Environmental Sciences Division, Oak Ridge National Laboratory, Oak Ridge, TN (United States)

2013-01-15

The insensitive munitions compound 2,4-dinitroanisole (DNAN) is increasingly being used as a replacement for traditional, sensitive munitions compounds (e.g., trinitrotoluene [TNT]), but the environmental fate and photo-transformation of DNAN in natural water systems are currently unknown. In this study, we investigated the photo-transformation rates of DNAN with both ultraviolet (UV) and sunlight irradiation under different environmentally relevant conditions. Sunlight photo-transformation of DNAN in water was found to follow predominantly pseudo-first-order decay kinetics with an average half-life (t{sub 1/2}) of approximately 0.70 d and activation energy (E{sub a}) of 53 kJ mol{sup −1}. Photo-transformation rates of DNAN were dependent on the wavelength of the light source: irradiation with UV-B light (280–315 nm) resulted in a greater quantum yield of transformation (ϕ{sub UV-B} = 3.7 × 10{sup −4}) than rates obtained with UV-A light (ϕ{sub UV-A} = 2.9 × 10{sup −4} at 316–400 nm) and sunlight (ϕ{sub sun} = 1.1 × 10{sup −4}). Photo-oxidation was the dominant mechanism for DNAN photo-transformation, based on the formation of nitrite (NO{sub 2}{sup −}) and nitrate (NO{sub 3}{sup −}) as major N species and 2,4-dinitrophenol as the minor species. Environmental factors (e.g., temperature, pH, and the presence or absence of naturally dissolved organic matter) displayed modest to little effects on the rate of DNAN photo-transformation. These observations indicate that sunlight-induced photo-transformation of DNAN may represent a significant abiotic degradation pathway in surface water, which may have important implications in evaluating the potential impacts and risks of DNAN in the environment. - Highlights: ► DNAN photo-transformation kinetics was dependent on light source and temperature. ► Photolysis produced harmful by-products that included dinitrophenol and nitrate. ► Photo-oxidation was determined to be the likely pathway of DNAN

Stripping in hot mix asphalt produced by aggregates from construction and demolition waste.

Science.gov (United States)

Pérez, I; Pasandín, A R; Gallego, J

2012-01-01

This paper analyses the effect of water on the durability of hot asphalt mixtures made with recycled aggregates from construction and demolition debris. Indirect tensile stress tests were carried out to evaluate stripping behaviour. The mixtures tested were fabricated with 0, 20, 40 and 60% recycled aggregates. Two types of natural aggregates were used: schist and calcite dolomite. An increase in the percentage of recycled aggregates was found to produce a decrease in the tensile stress ratio of the hot asphalt mixtures. To study this phenomenon, two and three factor analyses of variance (ANOVA) were performed with indirect tensile stress being used as the dependent variable. The factors studied were the percentage of recycled aggregates (0, 20, 40 and 60%), the moisture state (dry, wet) and the type of natural aggregate (schist, calcite). On the basis of the ANOVA results, it was found that the most important factor affecting resistance was the moisture state (dry, wet) of the specimens. The percentage of recycled aggregate also affected indirect tensile stress, especially in the dry state. The type of natural aggregate did not have a significant effect on indirect tensile stress. The hot asphalt mixture specimens made with different percentages of recycled aggregates from construction and demolition debris and of natural quarry aggregates showed poor stripping behaviour. This stripping behaviour can be related to both the poor adhesion of the recycled aggregates and the high absorption of the mortar of cement adhered to them.

Comparison of leaching tests to determine and quantify the release of inorganic contaminants in demolition waste

International Nuclear Information System (INIS)

Delay, Markus; Lager, Tanja; Schulz, Horst D.; Frimmel, Fritz H.

2007-01-01

The changes in waste management policy caused by the massive generation of waste materials (e.g. construction and demolition waste material, municipal waste incineration products) has led to an increase in the reuse and recycling of waste materials. For environmental risk assessment, test procedures are necessary to examine waste materials before they can be reused. In this article, results of column and lysimeter leaching tests having been applied to inorganic compounds in a reference demolition waste material are presented. The results show a good agreement between the leaching behaviour determined with the lysimeter unit and the column units used in the laboratory. In view of less time and system requirements compared to lysimeter systems, laboratory column units can be considered as a practicable instrument to assess the time-dependent release of inorganic compounds under conditions similar to those encountered in a natural environment. The high concentrations of elements in the seepage water at the initial stage of elution are reflected by the laboratory column leaching tests. In particular, authorities or laboratories might benefit and have an easy-to-use, but nevertheless reliable, method to serve as a basis for decision-making

Innovative probabilistic risk assessment applications: barrier impairments and fracture toughness. 2. Demolition Debris and Tornado Missile Hazard During Decommissioning

International Nuclear Information System (INIS)

Calhoun, David; Shepherd, Stephen

2001-01-01

During their operating lives, nuclear power plants typically maintain a high level of control over the amount of debris that is allowed to accumulate at the plant site. Although primarily intended to reduce the potential for fire damage, some plants also rely on these controls to limit the damage that could be caused during a tornado from missiles generated from loose debris. Demolition work associated with power plant decommissioning inevitably increases the quantity of debris. When bulk commodities such as piping and electrical distribution components are demolished, they are subject to various staging, handling, and storage processes before they can be released from the site. The demolition of plant structures dramatically increases the quantity of loose steel and concrete debris. For the foreseeable future, all plants that undertake decommissioning will have spent-fuel assemblies present on the plant site during the demolition project whether the spent fuel remains stored in a spent-fuel pool or is transferred to an independent spent-fuel storage installation (ISFSI). Under present regulations, protection from tornado missiles would be required for both types of spent-fuel storage. In addition, a small proportion of decommissioning plants will have operating units in close proximity. Licensing commitments for tornado missile protection may mandate controls on the production or storage of demolition debris. This paper presents a case study of the San Onofre Nuclear Generating Station (Fig. 1). Tornado missile protection licensing commitments from three types of facilities will be in force during the decommissioning of San Onofre Unit 1 (Unit 1): 1. Unit 1, under a possession-only license; 2. an ISFSI that will eventually store spent fuel from Unit 1; 3. San Onofre Operating Unit 2 (Unit 2) and San Onofre Operating Unit 3 (Unit 3). Together, these three facilities illustrate the range of impacts that licensing commitments designed for tornado protection may

Heavy metals in recovered fines from construction and demolition debris recycling facilities in Florida.

Science.gov (United States)

Townsend, Timothy; Tolaymat, Thabet; Leo, Kevin; Jambeck, Jenna

2004-10-01

A major product recovered from the processing and recycling of construction and demolition (C&D) debris is screened soil, also referred to as fines. A proposed reuse option for C&D debris fines is fill material, typically in construction projects as a substitute for natural soil. Waste material that is reused in a manner similar to soil must first be characterized to examine potential risks to human health and the environment. In Florida, samples of C&D debris fines from 13 C&D debris recycling facilities were characterized for 11 total and leachable heavy metal concentrations. Total metal concentration results (mg/kg) were compared to existing data on background Florida soil concentrations and to Florida's risk-based soil cleanup target levels (SCTLs). All of the detected metals were found to be elevated with respect to background. The 95% upper confidence level of arsenic from 99 samples was 3.2 mg/kg; arsenic presented the greatest limitation to reuse when compared to the SCTLs. Lead was not found to pose a major problem, likely because of the relatively new building infrastructure in Florida, which results in less demolition debris and less material impacted by lead-based paint. The results of batch leaching tests conducted using simulated rainwater (mg/l) were compared directly to risk-based groundwater levels for Florida and were found not to pose a risk using existing risk assessment policies.

GENE EXPRESSION CHANGES IN ARABIDOPSIS THALIANA SEEDLING ROOTS EXPOSED TO THE MUNITION HEXAHYDRO-1,3,5-TRINITRO-1,3,5-TRIAZINE

Science.gov (United States)

Arabidopsis thaliana root transcriptome responses to the munition, hexahydro-1,3,5-trinitro-1,3,5-triazine (RDX), were assessed using serial analysis of gene expression (SAGE). Comparison of the transcriptional profile for the RDX response to a profile previously described for Ar...

Recycling of construction and demolition waste: case study in the Port of Antwerp

OpenAIRE

Bergmans, Jef; Broos, Kris; Nielsen, Peter; Dierckx, Philippe; Brijsse, Yvan; Jacobs, Kurt

2015-01-01

Construction and demolition waste (C&DW) represents one of the EU’s largest waste streams. According to the Directive 2008/98/EC on waste, at least 70 percent (by weight) of non-hazardous C&DW must be recuperated by 2020. Eurostat estimates an annual C&DW generation of 970 Mton in EU-27, representing an average value of almost 2.0 ton per inhabitant, with an average recovery rate of 47%. A case study in the Port of Antwerp (PoA) demonstrated new high grade recycling options for purified mater...

Hybrid analysis of multiaxis electromagnetic data for discrimination of munitions and explosives of concern

Science.gov (United States)

Friedel, M. J.; Asch, T. H.; Oden, C.

2012-08-01

The remediation of land containing munitions and explosives of concern, otherwise known as unexploded ordnance, is an ongoing problem facing the U.S. Department of Defense and similar agencies worldwide that have used or are transferring training ranges or munitions disposal areas to civilian control. The expense associated with cleanup of land previously used for military training and war provides impetus for research towards enhanced discrimination of buried unexploded ordnance. Towards reducing that expense, a multiaxis electromagnetic induction data collection and software system, called ALLTEM, was designed and tested with support from the U.S. Department of Defense Environmental Security Technology Certification Program. ALLTEM is an on-time time-domain system that uses a continuous triangle-wave excitation to measure the target-step response rather than traditional impulse response. The system cycles through three orthogonal transmitting loops and records a total of 19 different transmitting and receiving loop combinations with a nominal spatial data sampling interval of 20 cm. Recorded data are pre-processed and then used in a hybrid discrimination scheme involving both data-driven and numerical classification techniques. The data-driven classification scheme is accomplished in three steps. First, field observations are used to train a type of unsupervised artificial neural network, a self-organizing map (SOM). Second, the SOM is used to simultaneously estimate target parameters (depth, azimuth, inclination, item type and weight) by iterative minimization of the topographic error vectors. Third, the target classification is accomplished by evaluating histograms of the estimated parameters. The numerical classification scheme is also accomplished in three steps. First, the Biot-Savart law is used to model the primary magnetic fields from the transmitter coils and the secondary magnetic fields generated by currents induced in the target materials in the

Hybrid analysis of multiaxis electromagnetic data for discrimination of munitions and explosives of concern

Science.gov (United States)

Friedel, M.J.; Asch, T.H.; Oden, C.

2012-01-01

The remediation of land containing munitions and explosives of concern, otherwise known as unexploded ordnance, is an ongoing problem facing the U.S. Department of Defense and similar agencies worldwide that have used or are transferring training ranges or munitions disposal areas to civilian control. The expense associated with cleanup of land previously used for military training and war provides impetus for research towards enhanced discrimination of buried unexploded ordnance. Towards reducing that expense, a multiaxis electromagnetic induction data collection and software system, called ALLTEM, was designed and tested with support from the U.S. Department of Defense Environmental Security Technology Certification Program. ALLTEM is an on-time time-domain system that uses a continuous triangle-wave excitation to measure the target-step response rather than traditional impulse response. The system cycles through three orthogonal transmitting loops and records a total of 19 different transmitting and receiving loop combinations with a nominal spatial data sampling interval of 20 cm. Recorded data are pre-processed and then used in a hybrid discrimination scheme involving both data-driven and numerical classification techniques. The data-driven classification scheme is accomplished in three steps. First, field observations are used to train a type of unsupervised artificial neural network, a self-organizing map (SOM). Second, the SOM is used to simultaneously estimate target parameters (depth, azimuth, inclination, item type and weight) by iterative minimization of the topographic error vectors. Third, the target classification is accomplished by evaluating histograms of the estimated parameters. The numerical classification scheme is also accomplished in three steps. First, the Biot–Savart law is used to model the primary magnetic fields from the transmitter coils and the secondary magnetic fields generated by currents induced in the target materials in the

A Biography of the Trousered Munitions Women’s Uniform of World War 1

OpenAIRE

Roberts, Jennifer

2017-01-01

Ce chapitre fournit une vue d’ensemble de la recherche pour un exemple survivant de l’uniforme de pantalons des « munitionettes », alors que les travailleurs dans les usines de munitions dans la Première Guerre Mondiale étaient reconnus. Si nous examinons la réaction sur les femmes qui portent un vêtement d’homme et les discussions d’émancipation de cet uniforme, ces recherches ont étudié considérablement les archives jadis moins utilisées dans l’histoire des vêtements. Comme il n’existe plus...

Detuned mechanical parametric amplification as a quantum non-demolition measurement

International Nuclear Information System (INIS)

Szorkovszky, A; Bowen, W P; Clerk, A A; Doherty, A C

2014-01-01

Recently it has been demonstrated that the combination of continuous position detection with detuned parametric driving can lead to significant steady-state mechanical squeezing, far beyond the 3 dB limit normally associated with parametric driving. In this work, we show the close connection between this detuned scheme and quantum non-demolition (QND) measurement of a single mechanical quadrature. In particular, we show that applying an experimentally realistic detuned parametric drive to a cavity optomechanical system allows one to effectively realize a QND measurement despite being in the bad-cavity limit. In the limit of strong squeezing, we show that this scheme offers significant advantages over standard backaction evasion, not only by allowing operation in the weak measurement and low efficiency regimes, but also in terms of the purity of the mechanical state

Environmental assessment for the salvage/demolition of 200 West Area, 200 East Area, and 300 Area steam plants

International Nuclear Information System (INIS)

1996-10-01

This environmental assessment has been prepared to assess potential environmental impacts associated with the US Department of Energy's proposed action: the salvage/demolition of the 200 West Area, 200 East Area, and 300 Area Steam Plants and steam distribution piping. Impact information will be used by the US Department of Energy, Richland Operations Office Manager, to determine if the proposed action is a major federal action significantly affecting the quality of the human environment. If the proposed action is determined to be major and significant, an environmental impact statement will be prepared. If the proposed action is determined not to be major and significant, a Finding of No Significant Impact (FONSI) will be issued and the action can proceed. The proposed action involves the salvage and demolition of the 200 West Area, 200 East Are, and 300 Area steam plants and their associated steam distribution piping, equipment, and ancillary facilities. Activities include the salvaging and recycling of all materials, wastes, and equipment where feasible, with waste minimization efforts utilized

Demolition of Munitions Storage Area Facilities. Right Size Project 10-0192C

Science.gov (United States)

2011-07-01

valuable, these resources also provide essential aesthetic, recreational, and socioeconomic benefits to society. The analysis focuses on plant and animal...community type, Ponderosa pine/snowberry, ( pinus ponderosa/symphocarpus albus) is listed as a rare community type by the state of Washington and occurs in...asphalt and/or concrete planned for removal may contain petroleum based materials from leaking equipment parked on these structures. Oils /tars may

Hydrogen sulfide flux measurements from construction and demolition debris (C&D) landfills.

Science.gov (United States)

Eun, Sangho; Reinhart, Debra R; Cooper, C David; Townsend, Timothy G; Faour, Ayman

2007-01-01

Hydrogen sulfide (H2S) has been identified as a principal odorous component of gaseous emissions from construction and demolition debris (C&D) landfills. Although several studies have reported the ambient concentrations of H2S near C&D landfills, few studies have quantified emission rates of H2S. One of the most widely used techniques for measuring surface gas emission rates from landfills is the flux chamber method. Flux measurements using the flux chamber were performed at five different C&D landfills from April to August, 2003. The flux rates of H2S measured in this research were between 0.192 and 1.76 mg/(m2-d).

Decontaminating agents and decontamination processes for nuclear industry and for plant demolition

International Nuclear Information System (INIS)

Henning, Klaus; Gojowczyk, Peter

2012-01-01

Decontamination of surfaces of materials in nuclear facilities or in nuclear power plants under demolition can be carried out successfully if surface treatment is performed by dipping or in an ultrasonic bath by alternating between alkaline and acid baths with intermediate rinsing in demineralized water. Decontaminating aluminium surfaces sensitive to corrosion requires further treatment in an ultrasonic bath, after the first 2 ultrasonic baths, with a weak alkaline decontaminating agent. This applies alike to components to be decontaminated for re-use and parts of materials to be disposed of. The decontamination action depends on the surfaces either being free from corrosion or else showing pronounced corrosion. (orig.)

An evaluation of the composition of soil cement bricks with construction and demolition waste - doi: 10.4025/actascitechnol.v33i2.9377

Directory of Open Access Journals (Sweden)

Antonio Anderson da Silva Segantini

2011-04-01

Full Text Available Sustainable development requires the existence of a production network that includes the reuse of construction waste for new materials. Current analysis investigates an optimal soil-cement composition made up of construction and demolition waste for the manufacture of pressed bricks. Soil-cement bricks were manufactured from construction and demolition wastes (CDW, A-4 classified fine sandy soil and cement CP II Z 32. Laboratory tests, comprising test compaction, optimum water content and maximum dry specific weight, consistency limits, grain size distribution and linear shrinkage, were made to characterize the materials researched. Compressive strength and absorption tests were also undertaken in different combinations of composition. Results showed that the application of CDW improved soil-cement qualities and reduced shrinkage of the material used.

Arsenal of democracy in the face of change: Precision Guided Munitions (PGMs), their evolution and some economic considerations, Working Paper No. 4

Energy Technology Data Exchange (ETDEWEB)

Chester, C.V.

1990-08-01

A brief study was made of some of the forces driving the move to Precision Guided Munitions (PGMs), including the quest for military effectiveness, combat experience, and logistic compression. PGMs cost from a few hundred to a few thousand dollars per Kg but are tens to hundreds of times more effective than conventional munitions. A year's peacetime plateau production of each US PGM can be carried by a few C-5 aircraft. Surge quantities of PGMs are within US airlift capabilities, taking some of the risk out of off-shore procurement. The improving capability of antiaircraft PGMs and the escalating cost of combat aircraft (50 to 100-fold in constant dollars since WW II) may bring into question the economic viability of manned attack aircraft. The same may be true to a slightly lesser degree for heavy armored vehicles. 14 refs., 5 tabs.

Heavy metals in recovered fines from construction and demolition debris recycling facilities in Florida

International Nuclear Information System (INIS)

Townsend, Timothy; Tolaymat, Thabet; Leo, Kevin; Jambeck, Jenna

2004-01-01

A major product recovered from the processing and recycling of construction and demolition (C and D) debris is screened soil, also referred to as fines. A proposed reuse option for C and D debris fines is fill material, typically in construction projects as a substitute for natural soil. Waste material that is reused in a manner similar to soil must first be characterized to examine potential risks to human health and the environment. In Florida, samples of C and D debris fines from 13 C and D debris recycling facilities were characterized for 11 total and leachable heavy metal concentrations. Total metal concentration results (mg/kg) were compared to existing data on background Florida soil concentrations and to Florida's risk-based soil cleanup target levels (SCTLs). All of the detected metals were found to be elevated with respect to background. The 95% upper confidence level of arsenic from 99 samples was 3.2 mg/kg; arsenic presented the greatest limitation to reuse when compared to the SCTLs. Lead was not found to pose a major problem, likely because of the relatively new building infrastructure in Florida, which results in less demolition debris and less material impacted by lead-based paint. The results of batch leaching tests conducted using simulated rainwater (mg/l) were compared directly to risk-based groundwater levels for Florida and were found not to pose a risk using existing risk assessment policies

Environmental management of construction and demolition waste in Kuwait.

Science.gov (United States)

Kartam, Nabil; Al-Mutairi, Nayef; Al-Ghusain, Ibrahim; Al-Humoud, Jasem

2004-01-01

There is an increasing pressure on the construction industry to reduce costs and improve the quality of our environment. The fact is that both of these goals can be achieved at the same time. Although construction and demolition (C&D) constitutes a major source of waste in terms of volume and weight, its management and recycling efforts have not yet seen the light in Kuwait. This study focuses on recycling efforts leading to the minimization of the total C&D waste that is currently landfilled in Kuwait. This paper presents the current status of C&D waste disposal system in Kuwait and identifies the potential problems to the environment, people and economy. Then, it investigates alternative solutions to manage and control this major type of waste in an economically efficient and environmentally safe manner. Next, the paper describes the feasibility of establishing a C&D waste recycling facility in Kuwait. It concludes by highlighting the major benefits and bottleneck problems with such a recycling facility.

Mammalian Toxicity of Munition Compounds. Phase II. Effects of Multiple Doses. Part III. 2,6-Dinitrotoluene

Science.gov (United States)

1976-07-01

and the neuromuscular effects in these dogs were not due to hypocalcemia . The lowest serum calcium concen- tration in these dogs was 4.2 meq/liter...motor end plate might produce a local hypocalcemia . Such a mechanism is purely speculative. Qualitatively and quantitavely, most of the effects of 2,6...I ýNw,- -MIM I/ MIDWEST RESEARCH INS14ITUTE H0q .3L I LU -_ MAMMALIAN TOXICITY OF MUNITIONS COMPOUlNDSPHASE II: EFFECTS OF MiULTIPLE DOSES C* •PART

Sustainable construction: construction and demolition waste reconsidered.

Science.gov (United States)

del Río Merino, Mercedes; Izquierdo Gracia, Pilar; Weis Azevedo, Isabel Salto

2010-02-01

Construction activity in Europe has increased substantially in the past decade. Likewise, there has also been a commensurate rise in the generation of construction and demolition waste (C&DW). This, together with the fact that in many European countries the rate of recycling and reuse of C&DW is still quite low has engendered a serious environmental problem and a motivation to develop strategies and management plans to solve it. Due to its composition, there is a significant potential to reuse and/or recycle C&DW, and thereby, contribute to improving the sustainability of construction and development, but practical procedures are not yet widely known or practiced in the construction industry. This article (a) summarizes the different applications that are presently practiced to optimize the recovery and/or application of C&DW for reuse, and (b) proposes various measures and strategies to improve the processing of this waste. The authors suggest that to enhance environmental effectiveness, a conscious and comprehensive C&DW management plan should be implemented in each jurisdiction. More precisely, this study presents a holistic approach towards C&DW management, through which environmental benefits can be achieved through the application of new construction methods that can contribute to sustainable growth.

Simulation of construction and demolition waste leachate

Energy Technology Data Exchange (ETDEWEB)

Townsend, T.G.; Jang, Y.; Thurn, L.G.

1999-11-01

Solid waste produced from construction and demolition (C and D) activities is typically disposed of in unlined landfills. Knowledge of C{ampersand}D debris landfill leachate is limited in comparison to other types of wastes. A laboratory study was performed to examine leachate resulting from simulated rainfall infiltrating a mixed C and D waste stream consisting of common construction materials (e.g., concrete, wood, drywall). Lysimeters (leaching columns) filled with the mixed C and D waste were operated under flooded and unsaturated conditions. Leachate constituent concentrations in the leachate from specific waste components were also examined. Leachate samples were collected and analyzed for a number of conventional water quality parameters including pH, alkalinity, total organic carbon, total dissolved solids, and sulfate. In experiments with the mixed C and D waste, high concentrations of total dissolved solids (TDS) and sulfate were detected in the leachate. C and D leachates produced as a result of unsaturated conditions exhibited TDS concentrations in the range of 570--2,200 mg/L. The major contributor to the TDS was sulfate, which ranged in concentration between 280 and 930 mg/L. The concentrations of sulfate in the leachate exceeded the sulfate secondary drinking water standard of 250 mg/L.

A change in strategy for a CERCLA Removal Action Demolition Project in progress results in overall project enhancements

International Nuclear Information System (INIS)

Albertin, M.; Nichols, R.M.; Edwards, D.T.

1995-01-01

This paper discusses changes made in a demolition project at the Fernald Environmental Management Project (FEMP), a site on the National Priorities list (NPL), owned by the Department of Energy. The project, to demolish fourteen uranium ore silos and their structure, was based on a Removal Action Work Plan, submitted and approved by the United States Environmental Protection Agency (USEPA), that integrated Comprehensive Environmental Response Compensation and Liability Act (CERCLA) requirements to remove the source of contamination and threat to public health and the environment. After the demolition contractor defaulted at 30% complete, completion of the project by the USEPA deadline was threatened. The recovery plan included re-evaluation of project documents in addition to the schedule. It was determined that re-interpretation of the removal action criteria, including design and Removal Action Work Plan, would eliminate road-blocks, and optimize resources, resulting in project completion by the original deadline even after lost-time in mobilizing another contractor. This presentation will discuss the open-quotes lessons learnedclose quotes by the project team and illustrate how simplification of construction methods resulted in enhancements to the environmental controls, improved material handing, and created a safer work environment

Quantifying construction and demolition waste: an analytical review.

Science.gov (United States)

Wu, Zezhou; Yu, Ann T W; Shen, Liyin; Liu, Guiwen

2014-09-01

Quantifying construction and demolition (C&D) waste generation is regarded as a prerequisite for the implementation of successful waste management. In literature, various methods have been employed to quantify the C&D waste generation at both regional and project levels. However, an integrated review that systemically describes and analyses all the existing methods has yet to be conducted. To bridge this research gap, an analytical review is conducted. Fifty-seven papers are retrieved based on a set of rigorous procedures. The characteristics of the selected papers are classified according to the following criteria - waste generation activity, estimation level and quantification methodology. Six categories of existing C&D waste quantification methodologies are identified, including site visit method, waste generation rate method, lifetime analysis method, classification system accumulation method, variables modelling method and other particular methods. A critical comparison of the identified methods is given according to their characteristics and implementation constraints. Moreover, a decision tree is proposed for aiding the selection of the most appropriate quantification method in different scenarios. Based on the analytical review, limitations of previous studies and recommendations of potential future research directions are further suggested. Copyright © 2014 Elsevier Ltd. All rights reserved.

Increasing the Safety in Recycling of Construction and Demolition Waste by Using Supervised Machine Learning

International Nuclear Information System (INIS)

Kuritcyn, P; Anding, K; Linß, E; Latyev, S M

2015-01-01

This paper discusses the possibility of the optical identification of recycled aggregates of construction and demolition waste (CDW) using methods of image processing, spectral analysis and machine learning. The classification performances in colour images shown, that we have to use other added spectral information to solve the recognition task in a satisfactory manner. In addition to investigations on a large colour image dataset first investigations in visible (VIS) and infrared (IR) spectrum were done for analysing significant characteristics in spectrum, which are useful for classification the C and D aggregates

Remedial investigation sampling and analysis plan for J-Field, Aberdeen Proving Ground, Maryland: Volume 2, Quality Assurance Project Plan

Energy Technology Data Exchange (ETDEWEB)

Prasad, S.; Martino, L.; Patton, T.

1995-03-01

J-Field encompasses about 460 acres at the southern end of the Gunpowder Neck Peninsula in the Edgewood Area of APG (Figure 2.1). Since World War II, the Edgewood Area of APG has been used to develop, manufacture, test, and destroy chemical agents and munitions. These materials were destroyed at J-Field by open burning and open detonation (OB/OD). For the purposes of this project, J-Field has been divided into eight geographic areas or facilities that are designated as areas of concern (AOCs): the Toxic Burning Pits (TBP), the White Phosphorus Burning Pits (WPP), the Riot Control Burning Pit (RCP), the Robins Point Demolition Ground (RPDG), the Robins Point Tower Site (RPTS), the South Beach Demolition Ground (SBDG), the South Beach Trench (SBT), and the Prototype Building (PB). The scope of this project is to conduct a remedial investigation/feasibility study (RI/FS) and ecological risk assessment to evaluate the impacts of past disposal activities at the J-Field site. Sampling for the RI will be carried out in three stages (I, II, and III) as detailed in the FSP. A phased approach will be used for the J-Field ecological risk assessment (ERA).

The International Atomic Energy Agency's program on decontamination and decommissioning

International Nuclear Information System (INIS)

Feraday, M.A.

1989-01-01

The International Atomic energy Agency (IAEA) is developing an integrated information base that will systematically cover the technical, regulatory, radiation protection, planning, and economic aspects related to the decontamination and decommissioning (D/D) of nuclear facilities. The object of this program is to assist member states in developing the required expertise, equipment, and programs so that they can decommission their nuclear facilities in a safe, timely, and cost-effective manner. In addition to providing information, the IAEA encourages research and provides technical assistance in the form of expert missions, equipment design and procurement, etc., to assist member states in implementing their D/D programs. The technology contained in some recent IAEA reports is reviewed, including the decontamination, segmentation, and demolition of concrete and steel; the recycle/reuse of components from decommissioning; and the reduction of occupational exposures in D/D and the regulatory process in decommissioning. The IAEA's future program is briefly reviewed

Bioconcentration factors and plant-water partition coefficients of munitions compounds in barley.

Science.gov (United States)

Torralba-Sanchez, Tifany L; Kuo, Dave T F; Allen, Herbert E; Di Toro, Dominic M

2017-12-01

Plants growing in the soils at military ranges and surrounding locations are exposed, and potentially able to uptake, munitions compounds (MCs). The extent to which a compound is transferred from the environment into organisms such as plants, referred to as bioconcentration, is conventionally measured through uptake experiments with field/synthetic soils. Multiple components/phases that vary among different soil types and affect the bioavailability of the MC, however, hinder the ability to separate the effects of soil characteristics from the MC chemical properties on the resulting plant bioconcentration. To circumvent the problem, this work presents a protocol to measure steady state bioconcentration factors (BCFs) for MCs in barley (Hordeum vulgare L.) using inert laboratory sand rather than field/synthetic soils. Three MCs: 2,4,6-trinitrotoluene (TNT), 2,4-dinitrotoluene (2,4-DNT), and 2,4-dinitroanisole (2,4-DNAN), and two munition-like compounds (MLCs): 4-nitroanisole (4-NAN) and 2-methoxy-5-nitropyridine (2-M-5-NPYNE) were evaluated. Approximately constant plant biomass and exposure concentrations were achieved within a one-month period that produced steady state log BCF values: 0.62 ± 0.02, 0.70 ± 0.03, 1.30 ± 0.06, 0.52 ± 0.03, and 0.40 ± 0.05 L kg plant dwt -1 for TNT, 2,4-DNT, 2,4-DNAN, 4-NAN, and 2-M-5-NPYNE, respectively. Furthermore, results suggest that the upper-bounds of the BCFs can be estimated within an order of magnitude by measuring the partitioning of the compounds between barley biomass and water. This highlights the importance of partition equilibrium as a mechanism for the uptake of MCs and MLCs by barley from interstitial water. The results from this work provide chemically meaningful data for prediction models able to estimate the bioconcentration of these contaminants in plants. Copyright © 2017 Elsevier Ltd. All rights reserved.

Development of porous ceramsite from construction and demolition waste.

Science.gov (United States)

Wang, Chuan; Wu, Jian-Zhi; Zhang, Fu-Shen

2013-01-01

The disposal of construction and demolition (C&D) waste has become a serious problem in China due to the rapid increase of Chinese construction industry in recent years. In the present study, typical C&D waste was employed for ceramsite fabrication so as to find a new way for its effective recycling. A novel process was developed for manufacturing high-quality porous ceramsite according to the special chemical composition and properties of C&D waste. Most importantly, a unique bloating agent was developed for the porous structure formation since it was difficult to obtain a suitable porous structure using traditional bloating agents. The effects of processing parameters such as sintering temperature, heating rate and soaking time were investigated, and the bloating mechanism for ceramsite was discussed. The C&D waste ceramsite (CDWC), with high-intensity, low density and homogeneous mechanical properties, was much more suitable for application in the construction field. This study provides a practical process for efficient recycling of the rapidly increasing quantities of C&D waste.

An integrated life cycle inventory for demolition processes in the context of life cycle sustainability assessment

DEFF Research Database (Denmark)

Bozhilova-Kisheva, Kossara Petrova; Hu, Mingming; van Roekel, Eric

2012-01-01

According to the Life Cycle Assessment in Building and Construction: State-of-the-Art Report (2003), the dismantling and demolition stage of the building life cycle is only sometimes included in the Life Cycle Inventory (LCI) when doing Life Cycle Assessments (LCA). The reason that it is less...... inventoried in a traditional LCA maybe because this stage is expected to have a negligible environmental impact comparing to other stages in the life cycle of the buildings. When doing a life cycle sustainability assessment considering not only environmental but also economic and social impacts, the impacts...

Computer-based test system for the Tactical Airfield Attack Munition (TAAM) safing, arming, and fuzing system

International Nuclear Information System (INIS)

Warhus, J.; Castleton, R.; Lanning, S.

1981-12-01

Testing and quality assurance of large numbers of firing systems are an essential part of the development of the Tactical Airfield Attack Munition (TAAM). A computerized test and data acquisition system has been developed to make the testing and quality assurance workload manageable. The system hardware utilizes an LSI-11/23 computer, a Tektronix 7612 transient digitizer, and various other programmable instruments and power supplies. The system is capable of measuring and analyzing mechanical shock and fireset transient waveforms, automating testing sequences, and making records and comparisons of the test results. The system architecture is flexible for general purpose firing system development work

DEMONSTRATION REPORT: Demonstration of Advanced Geophysics and Classification Technologies on Munitions Response Sites Former Fort Ord, Monterey County, CA

Science.gov (United States)

2017-06-01

DGM Digital Geophysical Mapping DTSC California Department of Toxic Substances Control EM Electromagnetic EPA U.S. Environmental...land mines, pyrotechnics, bombs , and demolition materials. Surface sweeps identified MEC items throughout Units 11 and 12, including 37mm, 40mm, 57mm...electromagnetic ( EM ) data are being collected. If no GPS readings are collected during that period, the most recent GPS position and the platform

Composition and leaching of construction and demolition waste: Inorganic elements and organic compounds

DEFF Research Database (Denmark)

Butera, Stefania; Christensen, Thomas Højlund; Astrup, Thomas Fruergaard

2014-01-01

Thirty-three samples of construction and demolition waste collected at 11 recycling facilities in Denmark were characterised in terms of total content and leaching of inorganic elements and presence of the persistent organic pollutants PCBs and PAHs. Samples included (i) "clean" (i.e. unmixed...... for leaching, was observed indicating that the number of analysed samples may be critical in relation to decisions regarding management and utilisation of the materials. Higher leaching of chromium, sulphate and chloride were observed for masonry-containing and partly carbonated samples, indicating that source...... segregation and management practices may be important. Generally, leaching was in compliance with available leaching limits, except for selenium, and in some cases chromium, sulphate and antimony. © 2014 Elsevier B.V....

Assessing metal contamination from construction and demolition (C&D) waste used to infill wetlands: using Deroceras reticulatum (Mollusca: Gastropoda).

Science.gov (United States)

Staunton, John A; Mc Donnell, Rory J; Gormally, Michael J; Williams, Chris D; Henry, Tiernan; Morrison, Liam

2014-11-01

Large quantities of construction and demolition waste (C&D) are produced globally every year, with little known about potential environmental impacts. In the present study, the slug, Deroceras reticulatum (Mollusca: Gastropoda) was used as the first biomonitor of metals (Ag, As, Ba, Cd, Co, Cr, Cu, Mn, Mo, Ni, Pb, Sb, Se, Ti, Tl, V and Zn) on wetlands post infilling with construction and demolition (C&D) waste. The bioaccumulation of As, Ba, Cd, Co, Sb, Se and Tl were found to be significantly elevated in slugs collected on C&D waste when compared to unimproved pastures (control sites), while Mo, Se and Sr had significantly higher concentrations in slugs collected on C&D waste when compared to known contaminated sites (mining locations), indicating the potential hazardous nature of C&D waste to biota. Identifying exact sources for these metals within the waste can be problematic, due to its heterogenic nature. Biomonitors are a useful tool for future monitoring and impact studies, facilitating policy makers and regulations in other countries regarding C&D waste infill. In addition, improving separation of C&D waste to allow increased reuse and recycling is likely to be effective in reducing the volume of waste being used as infill, subsequently decreasing potential metal contamination.

Microstructure of Concrete with Aggregates from Construction and Demolition Waste Recycling Plants.

Science.gov (United States)

Bravo, Miguel; Santos Silva, António; de Brito, Jorge; Evangelista, Luís

2016-02-01

This paper intends to analyze the microstructure of concrete with recycled aggregates (RA) from construction and demolition waste from various Portuguese recycling plants. To that effect, several scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) analyses were performed. Various concrete mixes were evaluated in order to analyze the influence of the RA's collection point and consequently of their composition on the mixes' characteristics. Afterward all the mixes were subjected to the capillary water absorption test in order to quantitatively evaluate their porosity. Results from the SEM/EDS analysis were compared with those from capillary water absorption test. The SEM/EDS analysis showed that the bond capacity of aggregates to the new cement paste is greatly influenced by the RA's nature. On the other hand, there was an increase in porosity with the incorporation of RA.

Soil retention of hexavalent chromium released from construction and demolition waste in a road-base-application scenario

DEFF Research Database (Denmark)

Butera, Stefania; Trapp, Stefan; Astrup, Thomas Fruergaard

2015-01-01

We investigated the retention of Cr(VI) in three subsoils with low organic matter content in laboratory experiments at concentration levels relevant to represent leachates from construction and demolition waste (C&DW) reused as unbound material in road construction. The retention mechanism appeared...... depth. However, in rigid climates and with high water infiltration through the road pavement, the reduction reaction could be so slow that Cr(VI) might migrate as deep as 200 cm under the road. The reaction parameters and the model can form the basis for systematically assessing under which scenarios Cr...

Weldon Spring Site Remedial Action Project approach to building dismantlement and demolition

Energy Technology Data Exchange (ETDEWEB)

Spittler, F.J.

1996-01-01

When remediation began at the Weldon Spring Site Remedial Action Project (WSSRAP), there were 41 buildings on site. Twenty-nine of these buildings were ancillary structures and were not used for processing radioactive material. Most of these have been torn down. The remaining 12 buildings were used for uranium and thorium processing or were major support structures, such as the laboratory. Two of the buildings were major processing operations occurred were successfully demolished in February of this year. Demolition of all structures will be complete in September of this year. To give an understanding of the magnitude of the work, the following is a description of the physical characteristics of the green salt building. This building was used to convert brown oxide (UO3) to green salt (UF4), which is the last intermediate step in purifying the mostly yellow cake feed material into uranium metal.

Weldon Spring Site Remedial Action Project approach to building dismantlement and demolition

International Nuclear Information System (INIS)

Spittler, F.J.

1996-01-01

When remediation began at the Weldon Spring Site Remedial Action Project (WSSRAP), there were 41 buildings on site. Twenty-nine of these buildings were ancillary structures and were not used for processing radioactive material. Most of these have been torn down. The remaining 12 buildings were used for uranium and thorium processing or were major support structures, such as the laboratory. Two of the buildings were major processing operations occurred were successfully demolished in February of this year. Demolition of all structures will be complete in September of this year. To give an understanding of the magnitude of the work, the following is a description of the physical characteristics of the green salt building. This building was used to convert brown oxide (UO3) to green salt (UF4), which is the last intermediate step in purifying the mostly yellow cake feed material into uranium metal

Arsenic and Old Mustard: Chemical Problems of Old Arsenical and 'Mustard' Munitions (Joseph F. Bunnett and Marian Mikotajczyk, Eds.)

Science.gov (United States)

Garrett, Benjamin

1999-10-01

What do Knute Rockne, Notre Dame's famed football coach, and Lewisite, a chemical warfare agent dubbed "the dew of death", have in common? Both owe their discovery to Father Julius Arthur Nieuwland.1 Rockne's legacy lives on in the Fighting Irish and their tradition of excellence on the gridiron. Lewisite, together with other arsenical- and mustard-type chemical warfare agents, provide a legacy that lives on, too, but with less cheerful consequences. The book Arsenic and Old Mustard: Chemical Problems of Old Arsenical and 'Mustard' Munitions makes clear the challenges faced in dealing with those consequences. This book documents the proceedings of a workshop devoted to arsenical- and mustard-type chemical warfare agents and their associated munitions. The workshop, held in Poland in 1996, included nine lectures, eight posters, and three discussion groups; and the contents of all these are presented. Major support for the workshop came from the Scientific Affairs Division of NATO as part of on ongoing series of meetings, cooperative research projects, and related efforts dealing with problems leftover from the Cold War and, in the case of the arsenicals and mustards, from conflicts dating to World War I. These problems can be seen in contemporary accounts, including a January 1999 news report that the U.S. Department of Defense intends to survey Washington, DC, areas near both American University and the Catholic University of America (CUA), site of the original synthesis of Lewisite, for chemical warfare agents and other materials disposed at the end of World War I.2 The first nine chapters of the book present the workshop's lectures. Of these, readers interested in chemical weapon destruction might find especially useful the first chapter, in which Ron Mansley of the Organisation for the Prohibition of Chemical Weapons presents a scholarly overview covering historical aspects of the arsenicals and mustards; their production and use; prospective destruction

Emissions of toxic pollutants from co-combustion of demolition and construction wood and household waste fuel blends.

Science.gov (United States)

Edo, Mar; Ortuño, Núria; Persson, Per-Erik; Conesa, Juan A; Jansson, Stina

2018-07-01

Four different types of fuel blends containing demolition and construction wood and household waste were combusted in a small-scale experimental set-up to study the effect of fuel composition on the emissions of polychlorinated dibenzo-p-dioxins (PCDDs), dibenzofurans (PCDFs), biphenyls (PCBs), chlorobenzenes (PCBzs), chlorophenols (PCPhs) and polycyclic aromatic hydrocarbons (PAHs). Two woody materials, commercial stemwood (ST) and demolition and construction wood (DC) were selected because of the differences in their persistent organic pollutants (POPs), ash and metals content. For household waste, we used a municipal solid waste (MSW) and a refuse-derived fuel (RDF) from MSW with 5-20 wt% and up to 5 wt% food waste content respectively. No clear effect on the formation of pollutants was observed with different food waste content in the fuel blends tested. Combustion of ST-based fuels was very inefficient which led to high PAH emissions (32 ± 3.8 mg/kg fuel ). The use of DC clearly increased the total PCDD and PCDF emissions (71 ± 26 μg/kg fuel ) and had a clear effect on the formation of toxic congeners (210 ± 87 ng WHO 2005 -TEQ/kg fuel ). The high PCDD and PCDF emissions from DC-based fuels can be attributed to the presence of material contaminants such as small pieces of metals or plastics as well as timber treated with chromated copper arsenate preservatives and pentachlorophenol in the DC source. Copyright © 2018 Elsevier Ltd. All rights reserved.

Estimation of building-related construction and demolition waste in Shanghai.

Science.gov (United States)

Ding, Tao; Xiao, Jianzhuang

2014-11-01

One methodology is proposed to estimate the quantification and composition of building-related construction and demolition (C&D) waste in a fast developing region like Shanghai, PR China. The varieties of structure types and building waste intensities due to the requirement of progressive building design and structure codes in different decades are considered in this regional C&D waste estimation study. It is concluded that approximately 13.71 million tons of C&D waste was generated in 2012 in Shanghai, of which more than 80% of this C&D waste was concrete, bricks and blocks. Analysis from this study can be applied to facilitate C&D waste governors and researchers the duty of formulating precise policies and specifications. As a matter of fact, at least a half of the enormous amount of C&D waste could be recycled if implementing proper recycling technologies and measures. The appropriate managements would be economically and environmentally beneficial to Shanghai where the per capita per year output of C&D waste has been as high as 842 kg in 2010. Copyright © 2014 Elsevier Ltd. All rights reserved.

Demolition of the FRJ-1 research reactor (MERLIN); Abbau des Reaktorblocks des Forschungsreaktors FRJ-1 (MERLIN)

Energy Technology Data Exchange (ETDEWEB)

Stahn, B.; Matela, K.; Zehbe, C. [Forschungszentrum Juelich GmbH (Germany); Poeppinghaus, J. [Gesellschaft fuer Nuklearservice, Essen (Germany); Cremer, J. [SNT Siempelkamp Nukleartechnik, Heidelberg (Germany)

2003-06-01

FRJ-2 (MERLIN), the swimming pool reactor cooled and moderated by light water, was built at the then Juelich Nuclear Research Establishment (KFA) between 1958 and 1962. In the period between 1964 and 1985, it was used for. The reactor was decommissioned in 1985. Since 1996, most of the demolition work has been carried out under the leadership of a project team. The complete secondary cooling system was removed by late 1998. After the cooling loops and experimental installations had been taken out, the reactor vessel internals were removed in 2000 after the water had been drained from the reactor vessel. After the competent authority had granted a license, demolition of the reactor block, the central part of the research reactor, was begun in October 2001. In a first step, the reactor operating floor and the reactor attachment structures were removed by the GNS/SNT consortium charged with overall planning and execution of the job. This phase gave rise to approx. The reactor block proper is dismantled in a number of steps. A variety of proven cutting techniques are used for this purpose. Demolition of the reactor block is to be completed in the first half of 2003. (orig.) [German] Der mit Leichtwasser gekuehlte und moderierte Schwimmbad-Forschungsreaktor FRJ-2 (MERLIN) wurde von 1958 bis 1962 fuer die damalige Kernforschungsanlage Juelich (KFA) errichtet. Von 1964 bis 1985 wurde er fuer Experimente mit zunaechst 5 MW und spaeter 10 MW thermischer Leistung bei einem maximalen thermischen Neutronenfluss von 1,1.10{sup 14} n/cm{sup 2}s genutzt. Im Jahr 1985 stellte der Reaktor seinen Betrieb ein. Die Brennelemente wurden aus der Anlage entfernt und in die USA und nach Grossbritannien verbracht. Seit 1996 erfolgen die wesentlichen Abbautaetigkeiten unter Leitung eines verantwortlichen Projektteams. Bis Ende 1998 wurde das komplette Sekundaerkuehlsystem entfernt. Dem Abbau der Kuehlkreislaeufe und Experimentiereinrichtungen folgte im Jahr 2000 der Ausbau der

Nanomaterials in construction and demolition - how can we assess the risk if we don't know where they are?

International Nuclear Information System (INIS)

Jones, Wendy; Gibb, Alistair; Goodier, Chris; Bust, Phil; Jin, Jie; Song, Mo

2015-01-01

This research, funded by the Institution of Occupational Safety and Health in the United Kingdom, has used a combination of literature review, web searching and unstructured interviews with a range of industry professionals to compile a list of products used in construction and the built environment which might contain nanomaterials. Samples of these products have been analysed using Scanning Electron Microscopy and Energy Dispersive X- Ray Spectroscopy to investigate whether nanomaterials are actually present and to what extent. Preliminary results of this testing are presented here. It is concluded that there is a discrepancy between the academic literature and the reality regarding the current application of nanomaterials in the construction industry and the built environment. There are also inaccuracies and deficiencies in the information provided by manufacturers which makes it difficult to accurately assess the location and application of nanomaterials within the industry. Further testing is planned to evaluate the risk of nanoparticle release from nano-enabled building products at their end of life by reproducing common demolition and recycling processes such as crushing, grinding, burning and melting. Results of this will form the basis of practical guidance for the construction, demolition and recycling industries to help them identify where particular protection or control measures may be appropriate as well as providing reassurance where no additional action is required. (paper)

Evaluation of the metabolic fate of munitions material (TNT & RDX) in plant systems. Initial assessment of plant DNA mutation spectra as a biomarker

Energy Technology Data Exchange (ETDEWEB)

Leung, F.; Cataldo, D.A.; Fellows, R.J.; Jarrell, A.E.; Harvey, S.D.

1995-09-01

Munitions material can enter the environment as a result of manufacturing activities and field usage. Predictor methodologies, or biomarkers would enhance evaluation of environmental impacts. The goal of this exploratory study deoxyribonucleic acid (DNA) mutation frequency as a biomarker for munitions exposure. The approach e resolution of an effective repetitive sequence probe for the identification of characteristic mutations, and (2) the development of a testing media [a clonal cell line of carrot (Daucus carota) spension cells]. Commercially available probes demonstrated marginal resolution therefore a low-C{sub o}t library was then constructed. Three colonies from the low-C{sub o}t DNA library were screened and the DNA isolates sequenced. A suspension culture of carrot (Daucus carota) was developed. A mutation spectra experiment was initiated at a 10-mg TNT/L exposure concentration with the attempt to clone over 1500 single TNT-exposed cells. Over the following six months greater than 98% of the initially isolated cells were unable to survive and produce micro calluses. The remaining calli were too few to be statistically significant and the experiment was terminated. The biomarker concept itself remains to be disproved, but the need for large numbers of uniform clones to differentiate true mutations suggest that more direct techniques using whole tissues need to be developed.

Nuclear Rocket Test Facility Decommissioning Including Controlled Explosive Demolition of a Neutron-Activated Shield Wall

International Nuclear Information System (INIS)

Michael Kruzic

2007-01-01

Located in Area 25 of the Nevada Test Site, the Test Cell A Facility was used in the 1960s for the testing of nuclear rocket engines, as part of the Nuclear Rocket Development Program. The facility was decontaminated and decommissioned (D and D) in 2005 using the Streamlined Approach For Environmental Restoration (SAFER) process, under the Federal Facilities Agreement and Consent Order (FFACO). Utilities and process piping were verified void of contents, hazardous materials were removed, concrete with removable contamination decontaminated, large sections mechanically demolished, and the remaining five-foot, five-inch thick radiologically-activated reinforced concrete shield wall demolished using open-air controlled explosive demolition (CED). CED of the shield wall was closely monitored and resulted in no radiological exposure or atmospheric release

Mitigation of Hexavalent Chromium in Storm Water Resulting from Demolition of Large Concrete Structure at the East Tennessee Technology Park - 12286

Energy Technology Data Exchange (ETDEWEB)

Britto, Ronnie; Brown, Bridget; Hale, Timothy B.; Hensley, Janice L.; Johnson, Robert T.; Patel, Madhu [Tetra Tech, Inc. (United States); Emery, Jerry A. [Energy Solutions, Inc. (United States); Gaston, Clyde [LATA-SHARP Remediation Services - LSRS (United States); Queen, David C. [U.S. DOE-ORO (United States)

2012-07-01

American Recovery and Reinvestment Act (ARRA) funding was provided to supplement the environmental management program at several DOE sites, including the East Tennessee Technology Park (ETTP) in Oak Ridge, Tennessee. Demolition of the ETTP K-33 Building, the largest building to be demolished to date in Oak Ridge, was awarded to LSRS in FY-2010 under the ARRA program. The K-33 building was an 82 foot tall 2-story structure covering approximately 32 acres. Once this massive building was brought down to the ground, the debris was segregated and consolidated into piles of concrete rubble and steel across the remaining pad. The process of demolishing the building, tracking across concrete debris with heavy equipment, and stockpiling the concrete rubble caused it to become pulverized. During and after storm events, hexavalent chromium leached from the residual cement present in the large quantities of concrete. Storm water control measures were present to preclude migration of contaminants off-site, but these control measures were not designed to control hexavalent chromium dissolved in storm water from reaching nearby receiving water. The following was implemented to mitigate hexavalent chromium in storm water: - Steel wool was distributed around K-33 site catch basins and in water pools as an initial step in addressing hexavalent chromium. - Since the piles of concrete were too massive and unsafe to tarp, they were placed into windrows in an effort to reduce total surface area. - A Hach colorimetric field meter was acquired by the K-33 project to provide realtime results of hexavalent chromium in site surface water. - Three hexavalent chromium treatment systems were installed at three separate catch basins that receive integrated storm water flow from the K-33 site. Sodium bisulfite is being used as a reducing agent for the immobilization of hexavalent chromium while also assisting in lowering pH. Concentrations initially were 310 - 474 ppb of hexavalent chromium in

Management of construction and demolition waste; Gestion de residuos de construccion y demolicion

Energy Technology Data Exchange (ETDEWEB)

Burgeno Munoz, A.

2004-07-01

The building sector is not considered a great pollutant although it does generate considerable amount of waste, traditionally called inert waste, as that is what it is composed of in the main, which requires specific management and for which specific rules and regulations are currently being drawn up (generally called Construction and Demolition Waste). So, far, for the mos part, they have ended up in the dump but a trend favouring recycling is the direct result of the regulations being drawn up and resultant financial criteria. The building industry will have to change its norms of conduct, it will have to start assessing waste, reduce the volume of the same and segregate properly what it generates. The former, necessarily linked with economic factors, factors relating to delivery dates and available space, will inevitably imply a change in the building sector in Spain in the medium term. (Author)

Re-use of construction and demolition residues and industrial wastes for the elaboration or recycled eco-efficient concretes

Energy Technology Data Exchange (ETDEWEB)

Juan Valdes, A.; Medina Martinez, C.; Guerra Romero, M. I.; Llamas Garcia, B.; Moran del Pozo, J. M.; Tascon Vegas, A.

2010-07-01

Production of residues from industries and construction and demolition sectors has increased during last years. The total amount of debris produced according to different estimations reaches values close to 42 million tonnes yr{sup -}1. Much of this waste has been thrown to landfill, without considering its potential for reuse, recycling or valuation. The aim of this research is to describe some of the physical and mechanical properties of different laboratory-mixed concretes, using various proportions of additional materials recovered from industrial waste and demolition rubble. The added materials are included either as admixtures (forestry residues, cork dust, steel fibre) or in partial substitution of natural aggregates (wire from electrical residues, tyre rubber, white ceramic, sanitary porcelain or shale). The laboratory tests have followed the standard EN protocols. Assay results were variable according to the nature of the material added to the mix: organic materials and shale, despite the steel fibre reinforcement, reduce the compression strength, but are suitable for the manufacture of lightweight concrete for agricultural pavements, with certain flexion resistance and a relatively good behaviour to impact. The substitution of natural aggregates with ceramic and porcelain wastes produces a significant increase in compression resistance, making them suitable for the manufacture of concrete with characteristic resistances above 40 MPa, which can be used both for structures or other agricultural elements: separators, feeders, slat floors. As a conclusion can be stated the possibility of reuse these wastes for the production of structural or non-structural concrete, with different applications in agricultural engineering. (Author) 36 refs.

Re-use of construction and demolition residues and industrial wastes for the elaboration or recycled eco-efficient concretes

International Nuclear Information System (INIS)

Juan Valdes, A.; Medina Martinez, C.; Guerra Romero, M. I.; Llamas Garcia, B.; Moran del Pozo, J. M.; Tascon Vegas, A.

2010-01-01

Production of residues from industries and construction and demolition sectors has increased during last years. The total amount of debris produced according to different estimations reaches values close to 42 million tonnes yr - 1. Much of this waste has been thrown to landfill, without considering its potential for reuse, recycling or valuation. The aim of this research is to describe some of the physical and mechanical properties of different laboratory-mixed concretes, using various proportions of additional materials recovered from industrial waste and demolition rubble. The added materials are included either as admixtures (forestry residues, cork dust, steel fibre) or in partial substitution of natural aggregates (wire from electrical residues, tyre rubber, white ceramic, sanitary porcelain or shale). The laboratory tests have followed the standard En protocols. Assay results were variable according to the nature of the material added to the mix: organic materials and shale, despite the steel fibre reinforcement, reduce the compression strength, but are suitable for the manufacture of lightweight concrete for agricultural pavements, with certain flexion resistance and a relatively good behaviour to impact. The substitution of natural aggregates with ceramic and porcelain wastes produces a significant increase in compression resistance, making them suitable for the manufacture of concrete with characteristic resistances above 40 MPa, which can be used both for structures or other agricultural elements: separators, feeders, slat floors. As a conclusion can be stated the possibility of reuse these wastes for the production of structural or non-structural concrete, with different applications in agricultural engineering. (Author) 36 refs.

Demolition, construction and excavation wastes in Copenhagen. Los residuos de demolicion, construccion y excavacion en Copenhague

Energy Technology Data Exchange (ETDEWEB)

Hahn, N.J.; Lauridsen, P.S.

1994-01-01

Demolition Waste, Construction Waste and Excavation Waste will in a modern society represent a major part of the total amount of the industrial wastes. Implementation of the Regulation for Industrial Waste in Copenhagen has resulted insignificant changes in the transportation and processing of this type of waste was typically disposed of as mixed waste on landfill sites and open dumps. Today most of this waste is sorted at the source (see figure 1) and recycled namely as secondary raw materials. This change in the disposal of construction waste etc, is due to two main factors: implementation of the regulation of commercial wastes and a significant raise in the (governmental) waste tax on specially landfilling activities. (Author)

Separability studies of construction and demolition waste recycled sand.

Science.gov (United States)

Ulsen, Carina; Kahn, Henrique; Hawlitschek, Gustav; Masini, Eldon A; Angulo, Sérgio C

2013-03-01

The quality of recycled aggregates from construction and demolition waste (CDW) is strictly related to the content of porous and low strength phases, and specifically to the patches of cement that remain attached to the surface of natural aggregates. This phase increases water absorption and compromises the consistency and strength of concrete made from recycled aggregates. Mineral processing has been applied to CDW recycling to remove the patches of adhered cement paste on coarse recycled aggregates. The recycled fine fraction is usually disregarded due to its high content of porous phases despite representing around 50% of the total waste. This paper focus on laboratory mineral separability studies for removing particles with a high content of cement paste from natural fine aggregate particles (quartz/feldspars). The procedure achieved processing of CDW by tertiary impact crushing to produce sand, followed by sieving and density and magnetic separability studies. The attained results confirmed that both methods were effective in reducing cement paste content and producing significant mass recovery (80% for density concentration and 60% for magnetic separation). The production of recycled sand contributes to the sustainability of the construction environment by reducing both the consumption of raw materials and disposal of CDW, particularly in large Brazilian centers with a low quantity of sand and increasing costs of this material due to long transportation distances. Copyright © 2012 Elsevier Ltd. All rights reserved.

Minimization and recycling of construction and demolition wastes; Minimizacion y reciclado de los residuos de construccion y demolicion (RCD)

Energy Technology Data Exchange (ETDEWEB)

Huete, R.; Lopez, J.A.; Ponce, M.; Llatas, C.

1998-12-01

We all know the damage to the environmental caused by the illegal dumping demolition waste, that causes a bad image of our cities. This damage, grows thanks to the inadequate governmental management and for the small co-operation of the owners of the wastes and we may quantify it with the necessary pressure and their impact on the environment has different aspects that should be remembered: on the economic media and on the culture. Following the recommendations of the European Union, we should place three different policies: prevention, recovery and sanitary landfilling. (Author)

Estimation of construction and demolition waste volume generation in new residential buildings in Spain.

Science.gov (United States)

Villoria Sáez, Paola; del Río Merino, Mercedes; Porras-Amores, César

2012-02-01

The management planning of construction and demolition (C&D) waste uses a single indicator which does not provide enough detailed information. Therefore the determination and implementation of other innovative and precise indicators should be determined. The aim of this research work is to improve existing C&D waste quantification tools in the construction of new residential buildings in Spain. For this purpose, several housing projects were studied to determine an estimation of C&D waste generated during their construction process. This paper determines the values of three indicators to estimate the generation of C&D waste in new residential buildings in Spain, itemizing types of waste and construction stages. The inclusion of two more accurate indicators, in addition to the global one commonly in use, provides a significant improvement in C&D waste quantification tools and management planning.

Ceramic and mixed construction and demolition wastes (CDW): a technically viable and environmentally friendly source of coarse aggregates for the concrete manufacture

OpenAIRE

Rodríguez, Desirée

2016-01-01

Nowadays, it is widely recognized that construction and demolition wastes (CDW) pose a significant environmental problem. However, in spite of the interest that the topic of their reutilization in the construction industry has aroused among worldwide researchers, the actual practice regarding the use of recycled aggregates from CDW is limited to low level applications (mostly as unbound materials). This fact is especially true for recycled aggregates containing ceramic materials, which are co...

Quantifying construction and demolition waste: An analytical review

International Nuclear Information System (INIS)

Wu, Zezhou; Yu, Ann T.W.; Shen, Liyin; Liu, Guiwen

2014-01-01

Highlights: • Prevailing C and D waste quantification methodologies are identified and compared. • One specific methodology cannot fulfill all waste quantification scenarios. • A relevance tree for appropriate quantification methodology selection is proposed. • More attentions should be paid to civil and infrastructural works. • Classified information is suggested for making an effective waste management plan. - Abstract: Quantifying construction and demolition (C and D) waste generation is regarded as a prerequisite for the implementation of successful waste management. In literature, various methods have been employed to quantify the C and D waste generation at both regional and project levels. However, an integrated review that systemically describes and analyses all the existing methods has yet to be conducted. To bridge this research gap, an analytical review is conducted. Fifty-seven papers are retrieved based on a set of rigorous procedures. The characteristics of the selected papers are classified according to the following criteria - waste generation activity, estimation level and quantification methodology. Six categories of existing C and D waste quantification methodologies are identified, including site visit method, waste generation rate method, lifetime analysis method, classification system accumulation method, variables modelling method and other particular methods. A critical comparison of the identified methods is given according to their characteristics and implementation constraints. Moreover, a decision tree is proposed for aiding the selection of the most appropriate quantification method in different scenarios. Based on the analytical review, limitations of previous studies and recommendations of potential future research directions are further suggested

Usage of air jigging for multi-component separation of construction and demolition waste.

Science.gov (United States)

Ambrós, Weslei Monteiro; Sampaio, Carlos Hoffmann; Cazacliu, Bogdan Grigore; Miltzarek, Gerson Luis; Miranda, Leonardo R

2017-02-01

The use of air jigging for performing multi-component separation in the treatment of mixed construction and demolition waste was studied. Sorting tests were carried out with mixtures of equal bulk volume of concrete and brick in which fixed quantities of unwanted materials - gypsum, wood and paper - were added. Experimental results have demonstrated the possibility to use air jigging to carry out both the removal of low-density contaminants and the concrete concentration in only one process step. In relation to the removal of contaminants only, the overall performance of jigging process can be comparable with that of commercial air classifiers and automatic sorting systems. Also, the initial content of contaminants seems does not have a significant effect on the separation extent. These results are of particular importance for recycling plants processing as they represent an alternative to optimize the use of air jigs. Further investigation is needed in order to evaluate the practical feasibility of such method. Copyright © 2016 Elsevier Ltd. All rights reserved.

Urban construction and demolition waste and landfill failure in Shenzhen, China.

Science.gov (United States)

Yang, Hong; Xia, Junqiang; Thompson, Julian R; Flower, Roger J

2017-05-01

On December 20, 2015 at 11:40 am a landslide in one of China's most advanced cities, Shenzhen, killed 73 people and damaged 33 buildings. In the absence of heavy rainfall or earthquakes, the landslide was an unexpected and profound shock to many people. According to China's Ministry of Land and Resources, the landslide was triggered by the collapse of an enormous pile of construction and demolition waste (CDW). With China's rapid urbanization, an increasing amount of CDW is being generated, especially in major cities. In total, China produces some 30% of the world's municipal solid waste and of this about 40% is CDW. To prevent landslides associated with CDW, the volume of waste dumped in landfills should be regulated. More specifically 4-Rs (reduce, reuse, recycle and recover) policies should be implemented more widely and efficiently. Although landfill will continue to be an important disposal option, proper management and careful monitoring of CDW are urgently needed to satisfy pressing safety issues. International collaboration, sharing of knowledge, and use of the latest technologies are needed so that the similar landslides can be prevented in China and elsewhere. Copyright © 2017 Elsevier Ltd. All rights reserved.

Construction quality assurance report for the Y-12 Construction/Demolition Landfill VII (CDL VII), Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Burton, P.M.

1994-11-01

This Construction Quality Assurance (CQA) Report provides documentation that Bid Option 2 of the Y-12 Plant Construction Demolition Landfill 7 (CDL-7) was constructed in substantial compliance with the Tennessee Department of Environment and Conservation (TDEC) approved design, as indicated and specified in the permit drawings, approved changes, and specifications. CDL-7 is located in Anderson County on the south side of Chestnut Ridge, approximately 0.5 miles south of the Y-12 Plant in Oak Ridge, Tennessee. This report applies specifically to the limits of excavation for Area No. 1 portions of the perimeter maintenance road and drainage channel and Sedimentation Pond No. 3. A partial ''As-Built'' survey was performed and is included

Evaluation of the metabolic fate of munitions material (TNT & RDX) in plant systems and initial assessment of material interaction with plant genetic material (DNA). Initial assessment of plant DNA adducts as biomarkers

Energy Technology Data Exchange (ETDEWEB)

Harvey, S.D.; Clauss, T.W.; Fellows, R.J.; Cataldo, D.A.

1995-08-01

Genetic damage to deoxyribonucleic acid (DNA) has long been suspected of being a fundamental event leading to cancer. A variety of causal factors can result in DNA damage including photodimerization of base pairs, ionizing radiation, specific reaction of DNA with environmental pollutants, and nonspecific oxidative damage caused by the action of highly reactive oxidizing agents produced by metabolism. Because organisms depend on an unadulterated DNA template for reproduction, DNA repair mechanisms are an important defense for maintaining genomic integrity. The objective of this exploratory project was to evaluate the potential for TNT to form DNA adducts in plants. These adducts, if they exist in sufficient quantities, could be potential biomarkers of munitions exposure. The ultimate goal is to develop a simple analytical assay for the determination of blomarkers that is indicative of munitions contamination. DNA repair exists in dynamic equilibrium with DNA damage. Repair mechanisms are capable of keeping DNA damage at remarkably low concentrations provided that the repair capacity is not overwhelmed.

Evaluating the performance and intellectual structure of construction and demolition waste research during 2000-2016.

Science.gov (United States)

Liu, Yanli; Sun, Tiantian; Yang, Lie

2017-08-01

Construction and demolition (C&D) waste diminishes scarce land resources and endangers human health and the surrounding environment. Quantitative and visualized analysis was conducted to evaluate worldwide scientific research output on C&D waste from 2000 to 2016. The related information of 857 publications was collected from SCI-Expanded database and statistically analyzed. The number of documents about C&D waste presented a general growth during the last 17 years. Construction and Building Materials publication ranked first in the most productive journals. China and Spain acted as dominated roles comparing to other countries, and Hong Kong Polytechnic University was the institution with the largest amount of C&D waste research. Recycled aggregates, sustainable C&D waste management, and the rewarding program and commerce system were the hottest topics during 2000-2016 and in the near future according to the intellectual structure analysis.

Digital Device Architecture and the Safe Use of Flash Devices in Munitions

Science.gov (United States)

Katz, Richard B.; Flowers, David; Bergevin, Keith

2017-01-01

Flash technology is being utilized in fuzed munition applications and, based on the development of digital logic devices in the commercial world, usage of flash technology will increase. Digital devices of interest to designers include flash-based microcontrollers and field programmable gate arrays (FPGAs). Almost a decade ago, a study was undertaken to determine if flash-based microcontrollers could be safely used in fuzes and, if so, how should such devices be applied. The results were documented in the Technical Manual for the Use of Logic Devices in Safety Features. This paper will first review the Technical Manual and discuss the rationale behind the suggested architectures for microcontrollers and a brief review of the concern about data retention in flash cells. An architectural feature in the microcontroller under study will be discussed and its use will show how to screen for weak or failed cells during manufacture, storage, or immediately prior to use. As was done for microcontrollers a decade ago, architectures for a flash-based FPGA will be discussed, showing how it can be safely used in fuzes. Additionally, architectures for using non-volatile (including flash-based) storage will be discussed for SRAM-based FPGAs.

Characterization of concrete made with recycled aggregate from concrete demolition waste

Directory of Open Access Journals (Sweden)

Terán Gilmore, A.

2007-12-01

Full Text Available The present study aimed: to characterize the physical, chemical and mechanical properties of recycled aggregate from construction and concrete structure demolition waste, processed before and after crushing; to characterize fresh and hardened concrete made with such recycled aggregate; and to design different doses varying the water/cement ratio, the amount of cement and the use of superplasticizing admixtures to offset the effects of absorption. The ultimate objective was to provide a broader perspective of the use of recycled aggregate in the manufacture of new concrete.El presente estudio nos permite caracterizar las propiedades físicas, químicas y mecánicas de los áridos reciclados, producto de residuos de la construcción y demolición de estructuras de hormigón, tratándolos antes y después de triturar; caracterizar el hormigón elaborado con áridos reciclados, en su estado fresco y endurecido, diseñando diferentes dosificaciones variando la relación agua/cemento, la cantidad de cemento y el uso de aditivos súper plastificantes para disminuir el efecto de la absorción; caracterización que nos permite tener una mayor perspectiva sobre el uso de áridos reciclados en la elaboración de nuevos hormigones.

Recycled blocks with improved sound and fire insulation containing construction and demolition waste.

Science.gov (United States)

Leiva, Carlos; Solís-Guzmán, Jaime; Marrero, Madelyn; García Arenas, Celia

2013-03-01

The environmental problem posed by construction and demolition waste (C&D waste) is derived not only from the high volume produced, but also from its treatment and disposal. Treatment plants receive C&D waste which is then transformed into a recycled mixed aggregate. The byproduct is mainly used for low-value-added applications such as land escape restoration, despite the high quality of the aggregate. In the present work, the chemical composition properties and grading curve properties of these aggregates are defined. Furthermore, the resulting recycled concrete with a high proportion of recycled composition, from 20% to 100% replacement of fine and coarse aggregate, is characterized physically and mechanically. An environmental study of the new construction material when all aggregates are substituted by C&D waste shows a low toxicity level, similar to that of other construction materials. The new material also has improved properties with respect to standard concrete such as high fire resistance, good heat insulation, and acoustic insulation. Copyright © 2012 Elsevier Ltd. All rights reserved.

Investigation into the Application of Construction and Demolition Waste in Urban Roads

Directory of Open Access Journals (Sweden)

Youyun Li

2017-01-01

Full Text Available The recycling and reuse of waste materials is a topic of global concern and great international interest for those interested in sustainable development and protecting the environment. In recent decades, global production of construction and demolition waste (C&D waste has significantly increased and became a worldwide problem. This research proposes to evaluate the feasibility of using aggregate from recycled C&D waste for urban road embankment applications based on the Sanhuan road construction project in eastern Xi’an. An extensive suite of laboratory and field compaction tests were carried out to determine the physical properties and engineering characteristics of the C&D waste. The effect of curing on the strength of the C&D waste was investigated using unconfined compression strength (UCS, California bearing ratio (CBR, and deflection tests. The results show that the C&D waste has the characteristics of high strength and significant stability after simple treatment and further suggest that the use of these materials for paving urban road embankments is feasible. This study is of value for the reasonable and effective promotion of using C&D waste recycled materials in road subgrade applications.

Atom-by-atom assembly

International Nuclear Information System (INIS)

Hla, Saw Wai

2014-01-01

Atomic manipulation using a scanning tunneling microscope (STM) tip enables the construction of quantum structures on an atom-by-atom basis, as well as the investigation of the electronic and dynamical properties of individual atoms on a one-atom-at-a-time basis. An STM is not only an instrument that is used to ‘see’ individual atoms by means of imaging, but is also a tool that is used to ‘touch’ and ‘take’ the atoms, or to ‘hear’ their movements. Therefore, the STM can be considered as the ‘eyes’, ‘hands’ and ‘ears’ of the scientists, connecting our macroscopic world to the exciting atomic world. In this article, various STM atom manipulation schemes and their example applications are described. The future directions of atomic level assembly on surfaces using scanning probe tips are also discussed. (review article)

Emergy analysis of the recycling options for construction and demolition waste.

Science.gov (United States)

Yuan, Fang; Shen, Li-yin; Li, Qi-ming

2011-12-01

Construction and demolition (C&D) waste is becoming a major contributor to environmental pollution. In Shanghai, China, the quantity of C&D waste is 2.11E+07 t/yr, which accounts for 45% of the total quantity of solid waste. There has been a growing promotion of recycling C&D waste as an effective way to solve this waste problem. However, the evaluation of the efficiency of recycling C&D waste as a potential source of resources is largely based on traditional economic analysis. The economic analysis emphasizes money instead of the harmony between economic benefit and environmental effects. There is a need for a new strategic approach to investigate the efficiency of recycling C&D waste to achieve the integration between economic, social and environmental effects. Emergy theory can be employed to analyze different recycling options for C&D waste. With reference to the Chinese construction industry, this paper demonstrates that the close-loop recycling option is better than the open-loop recycling option for C&D waste in terms of the integration of social, environmental and sustainable aspects. To evaluate different technology solutions for C&D waste recycling, the emergy theory and method is not limited to a cost-benefit balance but can include economic, social, environmental and sustainable effects. Copyright © 2011 Elsevier Ltd. All rights reserved.

Pop / Mart Juur

Index Scriptorium Estoniae

Juur, Mart, 1964-

2002-01-01

Heliplaatidest: Chicago "The Chicago Story: Complete Greatest Hits", Ryan Adams "Demolition", Elvis Presly "Elvis - 30 No.1 Hits", Komet +/vs. Bovine Life "Reciprocess +/vs. 1",, Cassius "Au Reve", Bowling For Soup "Drunk Enough To Dance", Atomic Kitten "Feels So Good"

PLUTONIUM FINISHING PLANT (PFP) 241-Z LIQUID WASTE TREATMENT FACILITY DEACTIVATION AND DEMOLITION

International Nuclear Information System (INIS)

JOHNSTON GA

2008-01-01

Fluor Hanford, Inc. (FH) is proud to submit the Plutonium Finishing Plant (PFP) 241-Z liquid Waste Treatment Facility Deactivation and Demolition (D and D) Project for consideration by the Project Management Institute as Project of the Year for 2008. The decommissioning of the 241-Z Facility presented numerous challenges, many of which were unique with in the Department of Energy (DOE) Complex. The majority of the project budget and schedule was allocated for cleaning out five below-grade tank vaults. These highly contaminated, confined spaces also presented significant industrial safety hazards that presented some of the most hazardous work environments on the Hanford Site. The 241-Z D and D Project encompassed diverse tasks: cleaning out and stabilizing five below-grade tank vaults (also called cells), manually size-reducing and removing over three tons of process piping from the vaults, permanently isolating service utilities, removing a large contaminated chemical supply tank, stabilizing and removing plutonium-contaminated ventilation ducts, demolishing three structures to grade, and installing an environmental barrier on the demolition site . All of this work was performed safely, on schedule, and under budget. During the deactivation phase of the project between November 2005 and February 2007, workers entered the highly contaminated confined-space tank vaults 428 times. Each entry (or 'dive') involved an average of three workers, thus equaling approximately 1,300 individual confined -space entries. Over the course of the entire deactivation and demolition period, there were no recordable injuries and only one minor reportable skin contamination. The 241-Z D and D Project was decommissioned under the provisions of the 'Hanford Federal Facility Agreement and Consent Order' (the Tri-Party Agreement or TPA), the 'Resource Conservation and Recovery Act of 1976' (RCRA), and the 'Comprehensive Environmental Response, Compensation, and Liability Act of 1980

Characterization of brominated flame retardants in construction and demolition waste components: HBCD and PBDEs.

Science.gov (United States)

Duan, Huabo; Yu, Danfeng; Zuo, Jian; Yang, Bo; Zhang, Yukui; Niu, Yongning

2016-12-01

The vast majority of construction material is inert and can be managed as nonhazardous. However, structures may have either been built with some environmentally unfriendly substances such as brominated flame retardants (BFRs), or have absorbed harmful elements such as heavy metals. This study focuses on end-of-life construction materials, i.e. construction and demolition (C&D) waste components. The aim was to characterize the concentration of extremely harmful substances, primarily BFRs, including hexabromocyclododecane (HBCD) and polybrominateddiphenyl ethers (PBDEs). Results revealed extremely high contents of HBCD and PBDEs in typical C&D waste components, particularly polyurethane foam materials. Policies should therefore be developed for the proper management of C&D waste, with priority for POP-containing debris. The first priority is to develop a classification system and procedures to separate out the harmful materials for more extensive processing. Additionally, identification and quantification of the environmental implications associated with dumping-dominated disposal of these wastes are required. Finally, more sustainable materials should be selected for use in the construction industry. Copyright © 2016 Elsevier B.V. All rights reserved.

Hydrogen sulfide generation in simulated construction and demolition debris landfills: impact of waste composition.

Science.gov (United States)

Yang, Kenton; Xu, Qiyong; Townsend, Timothy G; Chadik, Paul; Bitton, Gabriel; Booth, Matthew

2006-08-01

Hydrogen sulfide (H2S) generation in construction and demolition (C&D) debris landfills has been associated with the biodegradation of gypsum drywall. Laboratory research was conducted to observe H2S generation when drywall was codisposed with different C&D debris constituents. Two experiments were conducted using simulated landfill columns. Experiment 1 consisted of various combinations of drywall, wood, and concrete to determine the impact of different waste constituents and combinations on H2S generation. Experiment 2 was designed to examine the effect of concrete on H2S generation and migration. The results indicate that decaying drywall, even alone, leached enough sulfate ions and organic matter for sulfate-reducing bacteria (SRB) to generate large H2S concentrations as high as 63,000 ppmv. The codisposed wastes show some effect on H2S generation. At the end of experiment 1, the wood/drywall and drywall alone columns possessed H2S concentrations > 40,000 ppmv. Conversely, H2S concentrations were debris landfills are suggested.

Data Quality Objectives Summary Report for the Demolition of the 116-D and 116-DR Stacks

International Nuclear Information System (INIS)

Adler, J. G.

1999-01-01

This data quality objective (DQO) summary report has been developed to support demolition and disposal of the 116-D and 116-DR stacks in the 100-D Area of the Hanford Site. This project-specific summary was developed to meet the requirements in BHI-EE-01, Environmental Investigations Procedures, Procedure 1.2, ''Data Quality Objectives,'' using a simplified DQO process. The pathway for disposal of the 116-D and 116-DR stacks is the Environmental Restoration Disposal Facility (ERDF), which requires the development of a waste profile. A combination of process knowledge, history, and existing analogous data will be used to build a waste profile to dispose of the stack and plenum debris in the ERDF. Additional sample data are not necessary for waste designation. This report also addresses the Resources, Conservation, and Recovery Act of 1976 treatment, storage, and disposal closure requirements associated with the 116-DR stack

A study of explosive demolition techniques for heavy reinforced and prestressed concrete structures

International Nuclear Information System (INIS)

Fleischer, C.C.

1984-10-01

This report presents the results from a research programme aimed at advancing explosive demolition techniques from the present 'rule of thumb art' to a more scientifically based set of procedures to achieve the degree of control which will be essential in a nuclear power station decommissioning. The research is directed mainly at the biological shields of early Magnox reactors and the prestressed concrete pressure vessels (PCPVs) of later Magnox and Advanced Gas-cooled reactors. Relevant structures of other commercial nuclear power plants in the European Community, in particular the PCPVs of French Gas Graphite reactors and the biological shields of Light Water reactors are also considered. The bulk of the programme has been based on experiments with an extensive usage of scaled models. The programme investigated the use of buried explosive charges in cratering concrete and the use of shaped charges in stripping surface cover and drilling holes. After an initial parametric study the programme considered concrete layer stripping using multiple charges and culminated in the stripping off of an equivalent thickness of concrete, for radiation protection, from the inside walls of a complete cylindrical model of a biological shield. (author)

A study of explosive demolition techniques for heavy reinforced and prestressed concrete structures

International Nuclear Information System (INIS)

Fleischer, C.C.

1985-01-01

This report presents the results from a research programme aimed at advancing explosive demolition techniques from the present ''rule of thumb art'' to a more scientifically based set of procedures to achieve the degree of control which will be essential in a nuclear power station decommissioning. The research is directed mainly at the biological shields of early Magnox reactors and the prestressed concrete pressure vessels (PCPVs) of later Magnox and advanced gas-cooled reactors. Relevant structures of other commercial nuclear power plants in the European Community, in particular the PCPVs of French gas graphite reactors and the biological shields of light water reactors are also considered. The bulk of the programme has been based on experiments with an extensive usage of scaled models. The programme investigated the use of buried explosive charges in cratering concrete and the use of shaped charges in stripping surface cover and drilling holes. After an initial parametric study the programme considered concrete layer stripping using multiple charges and culminated in the stripping off of an equivalent thickness of concrete, for radiation protection, from the inside walls of a complete cylindrical model of a biological shield

Acoustic Resonance Spectroscopy (ARS) Munition Classification System enhancements. Final report

Energy Technology Data Exchange (ETDEWEB)

Vela, O.A.; Huggard, J.C.

1997-09-18

Acoustic Resonance Spectroscopy (ARS) is a non-destructive evaluation technology developed at the Los Alamos National Laboratory (LANL). This technology has resulted in three generations of instrumentation, funded by the Defense Special Weapons Agency (DSWA), specifically designed for field identification of chemical weapon (CW) munitions. Each generation of ARS instrumentation was developed with a specific user in mind. The ARS1OO was built for use by the U.N. Inspection Teams going into Iraq immediately after the Persian Gulf War. The ARS200 was built for use in the US-Russia Bilateral Chemical Weapons Treaty (the primary users for this system are the US Onsite Inspection Agency (OSIA) and their Russian counterparts). The ARS300 was built with the requirements of the Organization for the Prohibition of Chemical Weapons (OPCW) in mind. Each successive system is an improved version of the previous system based on learning the weaknesses of each and, coincidentally, on the fact that more time was available to do a requirements analysis and the necessary engineering development. The ARS300 is at a level of development that warrants transferring the technology to a commercial vendor. Since LANL will supply the computer software to the selected vendor, it is possible for LANL to continue to improve the decision algorithms, add features where necessary, and adjust the user interface before the final transfer occurs. This paper describes the current system, ARS system enhancements, and software enhancements. Appendices contain the Operations Manual (software Version 3.01), and two earlier reports on enhancements.

A photogrammetric methodology for estimating construction and demolition waste composition

International Nuclear Information System (INIS)

Heck, H.H.; Reinhart, D.R.; Townsend, T.; Seibert, S.; Medeiros, S.; Cochran, K.; Chakrabarti, S.

2002-01-01

Manual sorting of construction, demolition, and renovation (C and D) waste is difficult and costly. A photogrammetric method has been developed to analyze the composition of C and D waste that eliminates the need for physical contact with the waste. The only field data collected is the weight and volume of the solid waste in the storage container and a photograph of each side of the waste pile, after it is dumped on the tipping floor. The methodology was developed and calibrated based on manual sorting studies at three different landfills in Florida, where the contents of twenty roll-off containers filled with C and D waste were sorted. The component classifications used were wood, concrete, paper products, drywall, metals, insulation, roofing, plastic, flooring, municipal solid waste, land-clearing waste, and other waste. Photographs of each side of the waste pile were taken with a digital camera and the pictures were analyzed on a computer using Photoshop software. Photoshop was used to divide the picture into eighty cells composed of ten columns and eight rows. The component distribution of each cell was estimated and results were summed to get a component distribution for the pile. Two types of distribution factors were developed that allow the component volumes and weights to be estimated. One set of distribution factors was developed to correct the volume distributions and the second set was developed to correct the weight distributions. The bulk density of each of the waste components were determined and used to convert waste volumes to weights. (author)

A photogrammetric methodology for estimating construction and demolition waste composition

Energy Technology Data Exchange (ETDEWEB)

Heck, H.H. [Florida Inst. of Technology, Dept. of divil Engineering, Melbourne, Florida (United States); Reinhart, D.R.; Townsend, T.; Seibert, S.; Medeiros, S.; Cochran, K.; Chakrabarti, S

2002-06-15

Manual sorting of construction, demolition, and renovation (C and D) waste is difficult and costly. A photogrammetric method has been developed to analyze the composition of C and D waste that eliminates the need for physical contact with the waste. The only field data collected is the weight and volume of the solid waste in the storage container and a photograph of each side of the waste pile, after it is dumped on the tipping floor. The methodology was developed and calibrated based on manual sorting studies at three different landfills in Florida, where the contents of twenty roll-off containers filled with C and D waste were sorted. The component classifications used were wood, concrete, paper products, drywall, metals, insulation, roofing, plastic, flooring, municipal solid waste, land-clearing waste, and other waste. Photographs of each side of the waste pile were taken with a digital camera and the pictures were analyzed on a computer using Photoshop software. Photoshop was used to divide the picture into eighty cells composed of ten columns and eight rows. The component distribution of each cell was estimated and results were summed to get a component distribution for the pile. Two types of distribution factors were developed that allow the component volumes and weights to be estimated. One set of distribution factors was developed to correct the volume distributions and the second set was developed to correct the weight distributions. The bulk density of each of the waste components were determined and used to convert waste volumes to weights. (author)

Methodology of environmental diagnosis for construction and demolition waste landfills: a tool for planning and making decisions.

Science.gov (United States)

Garrido, E; Calvo, F; Ramos, A F; Zamorano, M

2005-11-01

Current legislation in the European Union regarding landfills provides measures, procedures and guidance to prevent or reduce, insofar as possible, negative effects on the environment. This means that Member States must take measures so that landfills cannot operate unless the operator first presents a plan for the site, which includes the implementation of improvements considered necessary by the engineer for compliance with regulations. Researchers at the University of Granada have developed a method to ascertain the degree of environmental impact that a construction and demolition waste landfill may produce on its immediate surroundings. This methodology is based on environmental indexes; its objective is to give crucial information concerning possible environmental problems produced by a landfill. The data thus obtained will permit the elaboration of guidelines for improvements in the location, design, and operation of landfills, or in extreme cases, their dosing, sealing, and rehabilitation.

The Walls Come Tumbling Down: Decontamination and Demolition of 29 Manhattan Project and Cold War-Era Buildings and Structures at Los Alamos National Laboratory-12301

Energy Technology Data Exchange (ETDEWEB)

Chaloupka, Allan B.; Finn, Kevin P.; Parsons, Duane A. [Los Alamos National Laboratory, Los Alamos, New Mexico 87545 (United States)

2012-07-01

approximately 18,580 m{sup 2} (200,000 ft{sup 2}). The initially approved baseline for the ARRA D and D Project was to remove 22 buildings and structures that included approximately 14,680 m{sup 2} (158,000 ft{sup 2}) of footprint. By employing efficiencies during subcontracting, demolition, and waste segregation, the savings allowed an additional 1,580 m{sup 2} (17,000 ft{sup 2}) of footprint to be removed using ARRA funds. Additionally, the lessons learned from this experience were used to apply NNSA funding to the removal of six additional non-contaminated buildings and structures. In the end, 29 buildings and structures, including stacks, cooling towers and tanks, were removed from the mesa. The entire DP East area was cleared of buildings and sub-grade structures and the soils cleaned to residential standards. The total footprint reduction at TA-21 as a result of this effort was in excess of 17,650 m{sup 2} (190,000 ft{sup 2}). The use of a Laboratory self-performance team to start demolition of non-contaminated structures resulted in steady work performance early in the project while subcontracts were being put in place to perform more complicated abatement and contaminated demolition activities. Most importantly, there were no serious worker injuries and the minor injuries recorded were those common to construction type activities. Extensive monitoring along the site boundary demonstrated that no hazardous chemicals or radioactive contamination were released and radiological dose to the public was negligible. The ARRA demolition activities were completed six months in advance of the deadline for employing ARRA funds. Additionally, over 17,585 m{sup 3} (23,000 yds{sup 3}) of building demolition debris was safely removed from DP Mesa. All of the major buildings have been removed, unencumbered access to the SWMUs that are required to be cleaned up by the Consent Order with the state of New Mexico, has been achieved, and a significant portion of the mesa has been prepared to

Atom-surface potentials and atom interferometry

International Nuclear Information System (INIS)

Babb, J.F.

1998-01-01

Long-range atom-surface potentials characterize the physics of many actual systems and are now measurable spectroscopically in deflection of atomic beams in cavities or in reflection of atoms in atomic fountains. For a ground state, spherically symmetric atom the potential varies as -1/R 3 near the wall, where R is the atom-surface distance. For asymptotically large distances the potential is weaker and goes as -1/R 4 due to retardation arising from the finite speed of light. This diminished interaction can also be interpreted as a Casimir effect. The possibility of measuring atom-surface potentials using atomic interferometry is explored. The particular cases studied are the interactions of a ground-state alkali-metal atom and a dielectric or a conducting wall. Accurate descriptions of atom-surface potentials in theories of evanescent-wave atomic mirrors and evanescent wave-guided atoms are also discussed. (author)

Media Mobilization, Demolition-Resistant Families, and Contentious Politics.Reanalysis of the Event of Yihuang%媒介动员、钉子户与抗争政治 宜黄事件再分析

Institute of Scientific and Technical Information of China (English)

吕德文

2012-01-01

宜黄事件具有某种标志性意义,它颠覆了当代中国抗争政治的刻板印象,创造了一个新的抗争政治类型。宜黄事件原本是一个普通的钉子户抗争事件,在进入媒体的视野之前,它只是底层政治的一部分,当事人采用的基本上属于＂弱者的武器＂的方式,并且是地方性的、特殊的和双轨的,显著性和协同性都不高。由于媒介动员将政策的内在张力呈现于公众视野,钉子户利用这一政治机遇结构,不断创新了抗争表演,从而使宜黄事件发生了规模转变和极化,最终使事件发展成为一场要求保护弱势群体利益,发动制度变革的专业化社会运动的一部分,宜黄事件也就具有了普适性的、模式化的和自主的特征。宜黄事件的遣散是因为钉子户和媒体的抗争目标出现了竞争,而并非明确的适度制度化所致,这是当代中国国家建设中＂反体制＂的体制重建的一部分。%The contention event of Yihuang in September, 2010 is of great significance because it has changed the contention routine in contemporary China by adopting a new type of contentious politics. Before it became the media focus, Yihuang event was just another ordinary occurrence of residents resisting demolition of their houses, a part of the subaltern politics. The main contention strategies taken by the families under the order to move typically including negotiation with the local government in charge of demolition, intercepting visits to appeal, and seeking media attention. These are ＂weapons of the weak＂, parochial, local-specific, and bifurcated~ therefore, of low salience and poor coordination, usually unsuccessful to achieve contention objectives. This time, the Zhong family adopted an extreme contention means of self-immolation. Since the occurrence of this event, the large-scale involvement of the media has presented the inherent tension of policies to the public, and the demolition

Bremsstrahlung in atom-atom collisions

International Nuclear Information System (INIS)

Amus'ya, M.Y.; Kuchiev, M.Y.; Solov'ev, A.V.

1985-01-01

It is shown that in the collision of a fast atom with a target atom when the frequencies are on the order of the potentials or higher, there arises bremsstrahlung comparable in intensity with the bremsstrahlung emitted by an electron with the same velocity in the field of the target atom. The mechanism by which bremsstrahlung is produced in atom-atom collisions is elucidated. Results of specific calculations of the bremsstrahlung spectra are given for α particles and helium atoms colliding with xenon

Economic viability of demolition recycled wastes used during the construction of the subfloor of a building located in the east side of the city of São Paulo

OpenAIRE

Paschoalin Filho, João Alexandre; Storopoli, João Henrique; Duarte, Eric Brum Lima

2014-01-01

http://dx.doi.org/10.5902/2236117013750The civil construction industry is responsible for a considerable environmental impact, whether the demand for natural raw materials or the generation of waste from its activities. The Resolution 307 of 5 July 2002 of the National Environmental Council classified construction and demolition wastes into different classes according to their physical characteristics, and forms to submit its disposal. This resolution highlights that construction waste can´t ...

The development of an on-site container

International Nuclear Information System (INIS)

Glass, R.E.; McAllaster, M.E.; Jones, P.L.; McKinney, A.L.

1992-01-01

Sandia National Laboratories (SNL) has developed a package for the on-site transport of chemical munitions for the US Army. This package was designed to prevent the release of lethal quantities of chemical agents during transportation of munitions to the demilitarization facilities on-site. The packaging prevents auto-ignition of the munitions by limiting the thermal and structural assault on the munitions during an accident. This package, with some modifications to account for contents, may be suitable for the on-site transport of mixed wastes at United States Department of Energy facilities. This paper discusses the design and verification testing of the package. The safety criteria for the package were modeled after the International Atomic Energy Agency (IAEA) hypothetical accident sequence and modified to take credit for operational controls. The modified accident sequence consisted of drop, puncture, and thermal events. The post-accident leak rate was established to prevent harm to an exposed worker. The packaging has a mass of 8600 kg and can accommodate up to 3600 kg of contents. The interior of the package is 188 cm in diameter and 232 cm long. Two sample ports can be used to sample the interior of the package prior to opening the closure and an o-ring test port can be used to determine the leak rates prior to and after transport

Construction demolition wastes, Waelz slag and MSWI bottom ash: a comparative technical analysis as material for road construction.

Science.gov (United States)

Vegas, I; Ibañez, J A; San José, J T; Urzelai, A

2008-01-01

The objective of the study is to analyze the technical suitability of using secondary materials from three waste flows (construction and demolition waste (CDW), Waelz slag and municipal solid waste incineration (MSWI) bottom ash), under the regulations and standards governing the use of materials for road construction. A detailed technical characterization of the materials was carried out according to Spanish General Technical Specifications for Road Construction (PG3). The results show that Waelz slag can be adequate for using in granular structural layers, while CDW fits better as granular material in roadbeds. Likewise, fresh MSWI bottom ash can be used as roadbed material as long as it does not contain a high concentration of soluble salts. This paper also discusses the adequacy of using certain traditional test methods for natural soils when characterizing secondary materials for use as aggregates in road construction.

Biological sulfate removal from construction and demolition debris leachate: effect of bioreactor configuration.

Science.gov (United States)

Kijjanapanich, Pimluck; Do, Anh Tien; Annachhatre, Ajit P; Esposito, Giovanni; Yeh, Daniel H; Lens, Piet N L

2014-03-30

Due to the contamination of construction and demolition debris (CDD) by gypsum drywall, especially, its sand fraction (CDD sand, CDDS), the sulfate content in CDDS exceeds the posed limit of the maximum amount of sulfate present in building sand (1.73 g sulfate per kg of sand for the Netherlands). Therefore, the CDDS cannot be reused for construction. The CDDS has to be washed in order to remove most of the impurities and to obtain the right sulfate content, thus generating a leachate, containing high sulfate and calcium concentrations. This study aimed at developing a biological sulfate reduction system for CDDS leachate treatment and compared three different reactor configurations for the sulfate reduction step: the upflow anaerobic sludge blanket (UASB) reactor, inverse fluidized bed (IFB) reactor and gas lift anaerobic membrane bioreactor (GL-AnMBR). This investigation demonstrated that all three systems can be applied for the treatment of CDDS leachate. The highest sulfate removal efficiency of 75-85% was achieved at a hydraulic retention time (HRT) of 15.5h. A high calcium concentration up to 1,000 mg L(-1) did not give any adverse effect on the sulfate removal efficiency of the IFB and GL-AnMBR systems. Copyright © 2013 Elsevier B.V. All rights reserved.

PLUTONIUM FINISHING PLANT (PFP) 241-Z LIQUID WASTE TREATMENT FACILITY DEACTIVATION AND DEMOLITION

Energy Technology Data Exchange (ETDEWEB)

JOHNSTON GA

2008-01-15

Fluor Hanford, Inc. (FH) is proud to submit the Plutonium Finishing Plant (PFP) 241-Z liquid Waste Treatment Facility Deactivation and Demolition (D&D) Project for consideration by the Project Management Institute as Project of the Year for 2008. The decommissioning of the 241-Z Facility presented numerous challenges, many of which were unique with in the Department of Energy (DOE) Complex. The majority of the project budget and schedule was allocated for cleaning out five below-grade tank vaults. These highly contaminated, confined spaces also presented significant industrial safety hazards that presented some of the most hazardous work environments on the Hanford Site. The 241-Z D&D Project encompassed diverse tasks: cleaning out and stabilizing five below-grade tank vaults (also called cells), manually size-reducing and removing over three tons of process piping from the vaults, permanently isolating service utilities, removing a large contaminated chemical supply tank, stabilizing and removing plutonium-contaminated ventilation ducts, demolishing three structures to grade, and installing an environmental barrier on the demolition site . All of this work was performed safely, on schedule, and under budget. During the deactivation phase of the project between November 2005 and February 2007, workers entered the highly contaminated confined-space tank vaults 428 times. Each entry (or 'dive') involved an average of three workers, thus equaling approximately 1,300 individual confined -space entries. Over the course of the entire deactivation and demolition period, there were no recordable injuries and only one minor reportable skin contamination. The 241-Z D&D Project was decommissioned under the provisions of the 'Hanford Federal Facility Agreement and Consent Order' (the Tri-Party Agreement or TPA), the 'Resource Conservation and Recovery Act of 1976' (RCRA), and the 'Comprehensive Environmental Response, Compensation, and

Performance estimation for concretes made with recycled aggregates of construction and demolition waste of some Brazilian cities

Directory of Open Access Journals (Sweden)

Antonio Eduardo Bezerra Cabral

2012-12-01

Full Text Available The aim of this paper is to verify the influence of composition variability of recycled aggregates (RA of construction and demolition wastes (CDW on the performance of concretes. Performance was evaluated building mathematical models for compressive strength, modulus of elasticity and drying shrinkage. To obtain such models, an experimental program comprising 50 concrete mixtures was carried out. Specimens were casted, tested and results for compressive strength, modulus of elasticity and drying shrinkage were statistically analyzed. Models inputs are CDW composition observed at seven Brazilian cities. Results confirm that using RA from CDW for concrete building is quite feasible, independently of its composition, once compressive strength and modulus of elasticity still reached considerable values. We concluded the variability presented by recycled aggregates of CDW does not compromise their use for concrete building. However, this information must be used with caution, and experimental tests should always be performed to certify concrete properties.

Laser-assisted atom-atom collisions

International Nuclear Information System (INIS)

Roussel, F.

1984-01-01

The basic layer-assisted atom-atom collision processes are reviewed in order to get a simpler picture of the main physical facts. The processes can be separated into two groups: optical collisions where only one atom is changing state during the collision, the other acting as a spectator atom, and radiative collisions where the states of the two atoms are changing during the collision. All the processes can be interpreted in terms of photoexcitation of the quasimolecule formed during the collisional process. (author)

The health hazards of depleted uranium munitions. Part 1

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-05-01

There has been a substantial amount of public discussion on the health effects of the use of depleted uranium (DU), especially on the battlefield. The RoyaI Society therefore convened an independent expert Working Group to review the present state of scientific knowledge about the health and environmental effects of DU, in order to inform public debate. This is the first of two reports. It deals with the amounts of DU to which soldiers could be exposed on the battlefield, the risks from radiation, and what we know from epidemiological studies. We consider past and potential future exposures, the most likely exposures and the 'worst-case' exposures that cannot be excluded. Our second report, to be published later this year, will address the risks from toxic poisoning and environmental issues including risks to civilian populations. The group has consulted widely. It has focused on what is known scientifically about aspects that are relevant to health and has not considered the merits of using DU in munitions. Nor does this report analyse Gulf War syndrome, which has been the subject of other reports. DU is a toxic and weakly radioactive heavy metal that may have adverse consequences to human health, particularly if it enters the body through inhalation, ingestion or wounding. On the battlefield it is used in kinetic energy weapons designed to penetrate the armour of tanks and other vehicles. On impact substantial amounts of DU may be dispersed as particles that can be inhaled and as shrapnel. Our approach has been to estimate the typical levels of exposure on the battlefield over a wide range of scenarios, and the worst-case exposures that individuals are unlikely to exceed. From these we calculate the potential health risks from radiation. We have also considered epidemiological studies of occupational exposures to uranium in other situations as an independent source of information on the risks of inhaling DU particles, although we recognise that the

The health hazards of depleted uranium munitions. Part 1

International Nuclear Information System (INIS)

2001-01-01

There has been a substantial amount of public discussion on the health effects of the use of depleted uranium (DU), especially on the battlefield. The RoyaI Society therefore convened an independent expert Working Group to review the present state of scientific knowledge about the health and environmental effects of DU, in order to inform public debate. This is the first of two reports. It deals with the amounts of DU to which soldiers could be exposed on the battlefield, the risks from radiation, and what we know from epidemiological studies. We consider past and potential future exposures, the most likely exposures and the 'worst-case' exposures that cannot be excluded. Our second report, to be published later this year, will address the risks from toxic poisoning and environmental issues including risks to civilian populations. The group has consulted widely. It has focused on what is known scientifically about aspects that are relevant to health and has not considered the merits of using DU in munitions. Nor does this report analyse Gulf War syndrome, which has been the subject of other reports. DU is a toxic and weakly radioactive heavy metal that may have adverse consequences to human health, particularly if it enters the body through inhalation, ingestion or wounding. On the battlefield it is used in kinetic energy weapons designed to penetrate the armour of tanks and other vehicles. On impact substantial amounts of DU may be dispersed as particles that can be inhaled and as shrapnel. Our approach has been to estimate the typical levels of exposure on the battlefield over a wide range of scenarios, and the worst-case exposures that individuals are unlikely to exceed. From these we calculate the potential health risks from radiation. We have also considered epidemiological studies of occupational exposures to uranium in other situations as an independent source of information on the risks of inhaling DU particles, although we recognise that the parallels may

Atom Skimmers and Atom Lasers Utilizing Them

Science.gov (United States)

Hulet, Randall; Tollett, Jeff; Franke, Kurt; Moss, Steve; Sackett, Charles; Gerton, Jordan; Ghaffari, Bita; McAlexander, W.; Strecker, K.; Homan, D.

2005-01-01

Atom skimmers are devices that act as low-pass velocity filters for atoms in thermal atomic beams. An atom skimmer operating in conjunction with a suitable thermal atomic-beam source (e.g., an oven in which cesium is heated) can serve as a source of slow atoms for a magneto-optical trap or other apparatus in an atomic-physics experiment. Phenomena that are studied in such apparatuses include Bose-Einstein condensation of atomic gases, spectra of trapped atoms, and collisions of slowly moving atoms. An atom skimmer includes a curved, low-thermal-conduction tube that leads from the outlet of a thermal atomic-beam source to the inlet of a magneto-optical trap or other device in which the selected low-velocity atoms are to be used. Permanent rare-earth magnets are placed around the tube in a yoke of high-magnetic-permeability material to establish a quadrupole or octupole magnetic field leading from the source to the trap. The atoms are attracted to the locus of minimum magnetic-field intensity in the middle of the tube, and the gradient of the magnetic field provides centripetal force that guides the atoms around the curve along the axis of the tube. The threshold velocity for guiding is dictated by the gradient of the magnetic field and the radius of curvature of the tube. Atoms moving at lesser velocities are successfully guided; faster atoms strike the tube wall and are lost from the beam.

Trend of the research on construction and demolition waste management

International Nuclear Information System (INIS)

Yuan Hongping; Shen Liyin

2011-01-01

Research interests in addressing construction and demolition (C and D) waste management issues have resulted in a large amount of publications during the last decade. This study demonstrates that there is no systematic examination on the research development in literature in the discipline of C and D waste management. This study presents the latest research trend in the discipline through analyzing the publications from 2000 to 2009 in eight major international journals. The analysis is conducted on the number of papers published annually, main authors' contributions, research methods and data analysis methods adopted, and research topics covered. The results exhibit an increasing research interest in C and D waste management in recent years. Researchers from developed economies have contributed significantly to the development of the research in the discipline. Some developing countries such as Malaysia and China have also been making good efforts in promoting C and D waste management research. The findings from this study also indicate that survey and case study are major methods for data collection, and the data are mostly processed through descriptive analysis. It is anticipated that more future studies on C and D waste management will be led by researchers from developing economies, where construction works will remain their major economic activities. On the other hand, more sophisticated modeling and simulating techniques have been used effectively in a number of studies on C and D waste management research, and this is considered a major methodology for future research in the discipline. C and D waste management will continue to be a hot research topic in the future, in particularly, the importance of human factors in C and D waste management has emerged as a new challenging topic.

Biological sulfate removal from gypsum contaminated construction and demolition debris.

Science.gov (United States)

Kijjanapanich, Pimluck; Annachhatre, Ajit P; Esposito, Giovanni; van Hullebusch, Eric D; Lens, Piet N L

2013-12-15

Construction and demolition debris (CDD) contains high levels of sulfate that can cause detrimental environmental impacts when disposed without adequate treatment. In landfills, sulfate can be converted to hydrogen sulfide under anaerobic conditions. CDD can thus cause health impacts or odor problems to landfill employees and surrounding residents. Reduction of the sulfate content of CDD is an option to overcome these problems. This study aimed at developing a biological sulfate removal system to reduce the sulfate content of gypsum contaminated CDD in order to decrease the amount of solid waste, to improve the quality of CDD waste for recycling purposes and to recover sulfur from CDD. The treatment leached out the gypsum contained in CDD by water in a leaching column. The sulfate loaded leachate was then treated in a biological sulfate reducing Upflow Anaerobic Sludge Blanket (UASB) reactor to convert the sulfate to sulfide. The UASB reactor was operated at 23 ± 3 °C with a hydraulic retention time and upflow velocity of 15.5 h and 0.1 m h(-1), respectively while ethanol was added as electron donor at a final organic loading rate of 3.46 g COD L(-1) reactor d(-1). The CDD leachate had a pH of 8-9 and sulfate dissolution rates of 526.4 and 609.8 mg L(-1) d(-1) were achieved in CDD gypsum and CDD sand, respectively. Besides, it was observed that the gypsum dissolution was the rate limiting step for the biological treatment of CDD. The sulfate removal efficiency of the system stabilized at around 85%, enabling the reuse of the UASB effluent for the leaching step, proving the versatility of the bioreactor for practical applications. Copyright © 2013 Elsevier Ltd. All rights reserved.

Trend of the research on construction and demolition waste management.

Science.gov (United States)

Yuan, Hongping; Shen, Liyin

2011-04-01

Research interests in addressing construction and demolition (C&D) waste management issues have resulted in a large amount of publications during the last decade. This study demonstrates that there is no systematic examination on the research development in literature in the discipline of C&D waste management. This study presents the latest research trend in the discipline through analyzing the publications from 2000 to 2009 in eight major international journals. The analysis is conducted on the number of papers published annually, main authors' contributions, research methods and data analysis methods adopted, and research topics covered. The results exhibit an increasing research interest in C&D waste management in recent years. Researchers from developed economies have contributed significantly to the development of the research in the discipline. Some developing countries such as Malaysia and China have also been making good efforts in promoting C&D waste management research. The findings from this study also indicate that survey and case study are major methods for data collection, and the data are mostly processed through descriptive analysis. It is anticipated that more future studies on C&D waste management will be led by researchers from developing economies, where construction works will remain their major economic activities. On the other hand, more sophisticated modeling and simulating techniques have been used effectively in a number of studies on C&D waste management research, and this is considered a major methodology for future research in the discipline. C&D waste management will continue to be a hot research topic in the future, in particularly, the importance of human factors in C&D waste management has emerged as a new challenging topic. Copyright © 2010 Elsevier Ltd. All rights reserved.

Life cycle assessment of construction and demolition waste management.

Science.gov (United States)

Butera, Stefania; Christensen, Thomas H; Astrup, Thomas F

2015-10-01

Life cycle assessment (LCA) modelling of construction and demolition waste (C&DW) management was carried out. The functional unit was management of 1 Mg mineral, source separated C&DW, which is either utilised in road construction as a substitute for natural aggregates, or landfilled. The assessed environmental impacts included both non-toxic and toxic impact categories. The scenarios comprised all stages of the end-of-life management of C&DW, until final disposal of all residues. Leaching of inorganic contaminants was included, as was the production of natural aggregates, which was avoided because of the use of C&DW. Typical uncertainties related to contaminant leaching were addressed. For most impact categories, utilisation of C&DW in road construction was preferable to landfilling; however, for most categories, utilisation resulted in net environmental burdens. Transportation represented the most important contribution for most nontoxic impacts, accounting for 60-95 per cent of these impacts. Capital goods contributed with negligible impacts. Leaching played a critical role for the toxic categories, where landfilling had lower impacts than utilisation because of the lower levels of leachate per ton of C&DW reaching the groundwater over a 100-year perspective. Leaching of oxyanions (As, V and Sb) was critical with respect to leaching. Typical experimental uncertainties in leaching data did not have a pivotal influence on the results; however, accounting for Cr immobilisation in soils as part of the impact assessment was critical for modelling the leaching impacts. Compared with the overall life cycle of building and construction materials, leaching emissions were shown to be potentially significant for toxicity impacts, compared with contributions from production of the same materials, showing that end-of-life impacts and leaching should not be disregarded when assessing environmental impacts from construction products and materials. CO2 uptake in the C

Estimation of the potential leakage of the chemical munitions based on two hydrodynamical models implemented for the Baltic Sea

Science.gov (United States)

Jakacki, Jaromir; Golenko, Mariya

2014-05-01

Two hydrodynamical models (Princeton Ocean Model (POM) and Parallel Ocean Program (POP)) have been implemented for the Baltic Sea area that consists of locations of the dumped chemical munitions during II War World. The models have been configured based on similar data source - bathymetry, initial conditions and external forces were implemented based on identical data. The horizontal resolutions of the models are also very similar. Several simulations with different initial conditions have been done. Comparison and analysis of the bottom currents from both models have been performed. Based on it estimating of the dangerous area and critical time have been done. Also lagrangian particle tracking and passive tracer were implemented and based on these results probability of the appearing dangerous doses and its time evolution have been presented. This work has been performed in the frame of the MODUM project financially supported by NATO.

Identifying areas under potential risk of illegal construction and demolition waste dumping using GIS tools.

Science.gov (United States)

Seror, Nissim; Portnov, Boris A

2018-05-01

Construction and demolition (C&D) waste, dumped illegally in ravines and open areas, contaminates soil and can cause underground water pollution and forests fires. Yet, effective monitoring of illegal C&D waste dumping and enforcing legislation against the offenders are often a difficult task due to the large size of geographic areas that need to be monitored, and limited human and financial resources available to environmental law enforcement agencies. In this study, we use Geographic Information System (GIS) tools and geo-statistical modelling to identify the areas under potentially elevated risk of illegal C&D waste dumping in the Haifa district of Israel. As our analysis shows, locational factors, significantly associated with the accumulated amount of waste in the existing illegal C&D waste sites, include: distance to the nearest main road, depth of the ravine present at the site (pwaste dumping for future monitoring. As we suggest, the proposed approach may be useful for environmental law enforcement authorities, by helping them to focus on specific sites for inspection, save resources, and act against the offenders more efficiently. Copyright © 2018 Elsevier Ltd. All rights reserved.

Atoms

International Nuclear Information System (INIS)

Fuchs, Alain; Villani, Cedric; Guthleben, Denis; Leduc, Michele; Brenner, Anastasios; Pouthas, Joel; Perrin, Jean

2014-01-01

Completed by recent contributions on various topics (atoms and the Brownian motion, the career of Jean Perrin, the evolution of atomic physics since Jean Perrin, relationship between scientific atomism and philosophical atomism), this book is a reprint of a book published at the beginning of the twentieth century in which the author addressed the relationship between atomic theory and chemistry (molecules, atoms, the Avogadro hypothesis, molecule structures, solutes, upper limits of molecular quantities), molecular agitation (molecule velocity, molecule rotation or vibration, molecular free range), the Brownian motion and emulsions (history and general features, statistical equilibrium of emulsions), the laws of the Brownian motion (Einstein's theory, experimental control), fluctuations (the theory of Smoluchowski), light and quanta (black body, extension of quantum theory), the electricity atom, the atom genesis and destruction (transmutations, atom counting)

Decontamination and demolition of concrete and metal structures during the decommissioning of nuclear facilities

International Nuclear Information System (INIS)

1988-01-01

The objective of this report is to give a concise technical description of the techniques and equipment being used or developed for the decontamination and demolition of nuclear facilities in sufficient detail to assist Member States to plan decommissioning operations and make preliminary evaluations of techniques and equipment. This report also reviews new and/or different aspects which have not been well covered previously in readily available review documents or IAEA publications. This report is an up to date review of techniques and equipment being used or developed for decontamination or dismantling work during the decommissioning of all types of nuclear facility except mining and milling sites. Although the information presented is aimed at countries initiating decommissioning programmes, it should also be useful to others who are responsible for or interested in the planning and implementation of decommissioning tasks. This report describes the relevant techniques and equipment, their areas of application and degree of development and the conditions in which they are used, when these details are known. However, this publication should be used in conjunction with other published technical information on these topics, experience gained as a result of previous decommissioning operations and the assistance of experts in the appropriate areas are required. 64 refs, 33 figs, 5 tabs

Consequences of the EU basic safety standards. Omission of the clearance for demolition/disposal with respect to the deconstruction projects of WAK GmbH

International Nuclear Information System (INIS)

Wittmann, S.

2013-01-01

The WAK GmbH's task is to decommission the nuclear installation projects at the KIT Campus Nord. These include the former Reprocessing Plant (WAK-Anlage), the Multi-purpose Research Reactor (MZFR), Research Reactor 2 (FR2), Compact Sodium-cooled Nuclear Reactor Facility (KNK), the Hot Cells (HZ) and some more small research facilities of the KIT. The buildings should be released by paragraph 29 German Radiation Protection Ordinance (StrlSchV) after the demolition of the process-engineering equipment. For this the clearance levels for 'demolition of buildings' Annex III Tab. 1 Column 10 (StrlSchV) must be reached, depth profiles were sampled on order to estimate how much material of the walls has to be removed to reach the values of the clearance levels. In a proposal (10926/12 ATO 90 SOC 501 SAN 149) on the basis of new scientific knowledge the EU plans to introduce clearance levels from the IAEA - ''Application of the Concepts of Exclusion, Exemption and Clearance RS-G-1.7''. In the proposal there are only clearance levels for an unrestricted release. Clearance levels for specific purpose (Annex III Tab. 1 Column 9a - 9d, 10 and 10a StrlSchV) are not named. A worst case scenario has been made what the possible effects are if the unrestricted release in the proposal of the basic safety standards from EU is guilty for every material. An estimation were done how much material and how much volume of building rubbish has to be removed to reach these new resulted clearance. Based on these volumes the caused additional financial costs for the final disposal for the WAK GmbH were calculated. (orig.)

Depleted uranium munitions - where are we now?

International Nuclear Information System (INIS)

Spratt, Brian G.

2002-01-01

There are very different views on the health hazards of DU munitions. Most of the concerns of veterans and their advisors focus on the radiological effects of DU and consequently these are the focus of this editorial. Effects on the kidney and environmental consequences are, however, considered in the second of the Royal Society reports and the main conclusions of both of the reports are outlined in the summary document published in this issue of the journal. The main radiological concerns focus on the irradiation of lung tissues from inhaled DU particles and irradiation resulting from the translocation of inhaled particles to the thoracic lymph nodes.The overwhelming scientific view, presented in the two Royal Society reports and in other independent reviews, is that the main risks of exposure to DU aerosols are an increase in lung cancer and (from chemical toxicity) damage to the kidney, although these are likely to be evident only following substantial intakes. The equivalent doses to the thoracic lymph nodes following inhalation of DU particles are about ten times greater than those to the lung, but the former tissue is considered to be relatively insensitive to radiation-induced cancers. So far, large-scale epidemiological studies of UK and US Gulf War veterans have shown no increase in mortality from cancer, or kidney disease, but these studies need to be continued to see if any significant excess mortality from these causes appears. As mentioned previously, more sensitive epidemiological studies should be possible if groups of soldiers who have known exposures to DU can be identified. Adverse reproductive effects have been observed in rodents exposed to uranium although most of these effects are evident after relatively large daily intakes of uranium. The possibility of effects on reproductive health (from DU or other toxic exposures) is being studied in both UK and US Gulf War veterans. Results from the UK epidemiological study are not yet available but

Use of engineered nanomaterials in the construction industry with specific emphasis on paints and their flows in construction and demolition waste in Switzerland.

Science.gov (United States)

Hincapié, Ingrid; Caballero-Guzman, Alejandro; Hiltbrunner, David; Nowack, Bernd

2015-09-01

One sector where the use of engineered nanomaterials (ENMs) is supposed to offer novel or improved functionalities is the construction industry. During the renovation or demolition of buildings, ENMs contained in former construction materials will enter recycling systems or become construction waste. Currently, information about ENM flows in these processes is insufficient. The potential for the release of ENMs from this waste into the environment is unknown, as are the environmental impacts. To evaluate whether there is currently any nano-relevant construction and demolition waste (C&DW) originating from buildings, we evaluated the sources and flows of ENMs in C&DW and identified their potential exposure pathways. A survey of business representatives of Swiss companies in this sector found that ENMs are mainly used in paints and cement. The most frequently used ENMs in the Swiss housing construction industry are nano-TiO2, nano-SiO2, nano-ZnO, and nano-Ag. Using a bottom-up, semi-quantitative approach, we estimated the flows of ENMs contained in paints along the product's life cycle from buildings to recycling and landfill. The flows of ENMs are determined by their associated flows of building materials. We estimated an annual amount of ENMs used in paints of 14t of TiO2, 12t of SiO2, 5t of ZnO, and 0.2t of Ag. The majority of ENMs contained in paints in Switzerland enter recycling systems (23t/y), a smaller amount is disposed directly in landfills (7t/y), and a tiny fraction of ENM waste is incinerated (0.01t/y). Our results allow a qualitative determination of the potential release of ENMs into technical or environmental compartments, with the highest potential release expected during recycling. Copyright © 2015 Elsevier Ltd. All rights reserved.

Quality assessment for recycling aggregates from construction and demolition waste: An image-based approach for particle size estimation.

Science.gov (United States)

Di Maria, Francesco; Bianconi, Francesco; Micale, Caterina; Baglioni, Stefano; Marionni, Moreno

2016-02-01

The size distribution of aggregates has direct and important effects on fundamental properties of construction materials such as workability, strength and durability. The size distribution of aggregates from construction and demolition waste (C&D) is one of the parameters which determine the degree of recyclability and therefore the quality of such materials. Unfortunately, standard methods like sieving or laser diffraction can be either very time consuming (sieving) or possible only in laboratory conditions (laser diffraction). As an alternative we propose and evaluate the use of image analysis to estimate the size distribution of aggregates from C&D in a fast yet accurate manner. The effectiveness of the procedure was tested on aggregates generated by an existing C&D mechanical treatment plant. Experimental comparison with manual sieving showed agreement in the range 81-85%. The proposed technique demonstrated potential for being used on on-line systems within mechanical treatment plants of C&D. Copyright © 2015 Elsevier Ltd. All rights reserved.

Single-atom lasing induced atomic self-trapping

International Nuclear Information System (INIS)

Salzburger, T.; Ritsch, H.

2004-01-01

We study atomic center of mass motion and field dynamics of a single-atom laser consisting of a single incoherently pumped free atom moving in an optical high-Q resonator. For sufficient pumping, the system starts lasing whenever the atom is close to a field antinode. If the field mode eigenfrequency is larger than the atomic transition frequency, the generated laser light attracts the atom to the field antinode and cools its motion. Using quantum Monte Carlo wave function simulations, we investigate this coupled atom-field dynamics including photon recoil and cavity decay. In the regime of strong coupling, the generated field shows strong nonclassical features like photon antibunching, and the atom is spatially confined and cooled to sub-Doppler temperatures. (author)

Many-body quantum simulation with Rydberg atoms and ions

International Nuclear Information System (INIS)

Mueller, M.

2010-01-01

quantum switch mechanism that involves electromagnetically induced transparency. In the following work, this many-particle entangling gate it then used as the principle building block for the development of a new Rydberg quantum simulation architecture. It is shown that laser-excited Rydberg atoms in optical or magnetic lattices provide an efficient implementation of a universal quantum simulator for spin models. Simulation protocols are developed that allow one to realize the coherent and dissipative time evolution of spin models involving higher-order interactions, such as Kitaev's toric code Hamiltonian and more complex lattice gauge theories. It is analyzed in detail how this can be achieved by stroboscopic sequences of multi-qubit Rydberg gates combined with dissipative steps via optical pumping. Based on multi-particle reservoir engineering the new scheme can also be used for the dissipative preparation of entangled states and many-body quantum phases. The work presented in the last part of this thesis has been performed in close collaboration with the group of Prof. Rainer Blatt at the Institute for Experimental Physics at the University of Innsbruck. In this project, novel possibilities for the quantum simulation of general open-system dynamics using trapped ions are explored both theoretically and in an experiment. A digital, i.e., gate-based quantum simulation scheme is developed that combines high-fidelity multi-ion entangling gates with optical pumping on auxiliary ions, for the realization of coherent and dissipative multi-qubit dynamics. The elementary building blocks of this simulation architecture have been demonstrated in an experiment that for the first time realizes a toolbox for simulating an open quantum system with up to five qubits. In the experiment, this engineering of general dynamics is illustrated by the dissipative preparation of entangled states, the simulation of coherent many-body spin interactions and the quantum non-demolition measurement

Ultracold atoms on atom chips

DEFF Research Database (Denmark)

Krüger, Peter; Hofferberth, S.; Haller, E.

2005-01-01

Miniaturized potentials near the surface of atom chips can be used as flexible and versatile tools for the manipulation of ultracold atoms on a microscale. The full scope of possibilities is only accessible if atom-surface distances can be reduced to microns. We discuss experiments in this regime...

Decontamination and demolition of a former plutonium processing facility's process exhaust system, firescreen, and filter plenum buildings

International Nuclear Information System (INIS)

LaFrate, P.J. Jr.; Stout, D.S.; Elliott, J.W.

1996-01-01

The Los Alamos National Laboratory (LANL) Decommissioning Project has decontaminated, demolished, and decommissioned a process exhaust system, two filter plenum buildings, and a firescreen plenum structure at Technical Area 21 (TA-2 1). The project began in August 1995 and was completed in January 1996. These high-efficiency particulate air (HEPA) filter plenums and associated ventilation ductwork provided process exhaust to fume hoods and glove boxes in TA-21 Buildings 2 through 5 when these buildings were active plutonium and uranium processing and research facilities. This paper summarizes the history of TA-21 plutonium and uranium processing and research activities and provides a detailed discussion of integrated work process controls, characterize-as-you-go methodology, unique engineering controls, decontamination techniques, demolition methodology, waste minimization, and volume reduction. Also presented in detail are the challenges facing the LANL Decommissioning Project to safely and economically decontaminate and demolish surplus facilities and the unique solutions to tough problems. This paper also shows the effectiveness of the integrated work package concept to control work through all phases

Decontamination and demolition of a former plutonium processing facility's process exhaust system, firescreen, and filter plenum buildings

International Nuclear Information System (INIS)

LaFrate, P.J. Jr.; Stout, D.S.; Elliott, J.W.

1996-01-01

The Los Alamos National Laboratory (LANL) Decommissioning Project has decontaminated, demolished, and decommissioned a process exhaust system, two filter plenum buildings, and a firescreen plenum structure at Technical Area 21 (TA-21). The project began in August 1995 and was completed in January 1996. These high-efficiency particulate air (HEPA) filter plenums and associated ventilation ductwork provided process exhaust to fume hoods and glove boxes in TA-21 Buildings 2 through 5 when these buildings were active plutonium and uranium processing and research facilities. This paper summarizes the history of TA-21 plutonium and uranium processing and research activities and provides a detailed discussion of integrated work process controls, characterize-as-you-go methodology, unique engineering controls, decontamination techniques, demolition methodology, waste minimization, and volume reduction. Also presented in detail are the challenges facing the LANL Decommissioning Project to safely and economically decontaminate and demolish surplus facilities and the unique solutions to tough problems. This paper also shows the effectiveness of the integrated work package concept to control work through all phases

Atomization of volatile compounds for atomic absorption and atomic fluorescence spectrometry: On the way towards the ideal atomizer

International Nuclear Information System (INIS)

Dedina, Jiri

2007-01-01

This review summarizes and discusses the individual atomizers of volatile compounds. A set of criteria important for analytical praxis is used to rank all the currently existing approaches to the atomization based on on-line atomization for atomic absorption (AAS) and atomic fluorescence spectrometry (AFS) as well as on in-atomizer trapping for AAS. Regarding on-line atomization for AAS, conventional quartz tubes are currently the most commonly used devices. They provide high sensitivity and low baseline noise. Running and investment costs are low. The most serious disadvantage is the poor resistance against atomization interferences and often unsatisfactory linearity of calibration graphs. Miniature diffusion flame (MDF) is extremely resistant to interferences, simple, cheap and user-friendly. Its essential disadvantage is low sensitivity. A novel device, known as a multiatomizer, was designed to overcome disadvantages of previous atomizers. It matches performance of conventional quartz tubes in terms of sensitivity and baseline noise as well as in running and investment costs. The multiatomizer, however, provides much better (i) resistance against atomization interferences and (ii) linearity of calibration graphs. In-atomizer trapping enhances the sensitivity of the determination and eliminates the effect of the generation kinetics and of surges in gas flow on the signal shape. This is beneficial for the accuracy of the determination. It could also be an effective tool for reducing some interferences in the liquid phase. In-situ trapping in graphite furnaces (GF) is presently by far the most popular approach to the in-atomizer trapping. Its resistance against interferences is reasonably good and it can be easily automated. In-situ trapping in GF is a mature method well established in various application fields. These are the reasons to rank in-situ trapping in GF as currently the most convenient approach to hydride atomization for AAS. The recently suggested

Atomic collisions related to atomic laser isotope separation

International Nuclear Information System (INIS)

Shibata, Takemasa

1995-01-01

Atomic collisions are important in various places in atomic vapor laser isotope separation (AVLIS). At a vaporization zone, many atomic collisions due to high density have influence on the atomic beam characteristics such as velocity distribution and metastable states' populations at a separation zone. In the separation zone, a symmetric charge transfer between the produced ions and the neutral atoms may degrade selectivity. We have measured atomic excitation temperatures of atomic beams and symmetric charge transfer cross sections for gadolinium and neodymium. Gadolinium and neodymium are both lanthanides. Nevertheless, results for gadolinium and neodymium are very different. The gadolinium atom has one 5d electron and neodymium atom has no 5d electron. It is considered that the differences are due to existence of 5d electron. (author)

Reduced sulfur compounds in gas from construction and demolition debris landfills.

Science.gov (United States)

Lee, Sue; Xu, Qiyong; Booth, Matthew; Townsend, Timothy G; Chadik, Paul; Bitton, Gabriel

2006-01-01

The biological conversion of sulfate from disposed gypsum drywall to hydrogen sulfide (H(2)S) in the anaerobic environment of a landfill results in odor problems and possible health concerns at many disposal facilities. To examine the extent and magnitude of such emissions, landfill gas samples from wells, soil vapor samples from the interface of the waste and cover soil, and ambient air samples, were collected from 10 construction and demolition (C&D) debris landfills in Florida and analyzed for H(2)S and other reduced sulfur compounds (RSC). H(2)S was detected in the well gas and soil vapor at all 10 sites. The concentrations in the ambient air above the surface of the landfill were much lower than those observed in the soil vapor, and no direct correlation was observed between the two sampling locations. Methyl mercaptan and carbonyl sulfide were the most frequently observed other RSC, though they occurred at smaller concentrations than H(2)S. This research confirmed the presence of H(2)S at C&D debris landfills. High concentrations of H(2)S may be a concern for employees working on the landfill site. These results indicate that workers should use proper personal protection at C&D debris landfills when involved in excavation, landfill gas collection, or confined spaces. The results indicate that H(2)S is sufficiently diluted in the atmosphere to not commonly pose acute health impacts for these landfill workers in normal working conditions. H(2)S concentrations were extremely variable with measurements occurring over a very large range (from less than 3 ppbv to 12,000 ppmv in the soil vapor and from less than 3 ppbv to 50 ppmv in ambient air). Possible reasons for the large intra- and inter-site variability observed include waste and soil heterogeneities, impact of weather conditions, and different site management practices.

Environmental risks of HBCDD from construction and demolition waste: a contemporary and future issue.

Science.gov (United States)

Nie, Zhiqiang; Yang, Ziliang; Fang, Yanyan; Yang, Yufei; Tang, Zhenwu; Wang, Xingrun; Die, Qingqi; Gao, Xingbao; Zhang, Fengsong; Wang, Qi; Huang, Qifei

2015-11-01

Hexabromocyclododecane (HBCDD), as one of the most widely used brominated flame retardants (BFRs), is of great concern globally because of its persistence in the environment and negative impacts on humans and animals. HBCDD has been mainly used in flame-retarded expanded (EPS) and extruded (XPS) polystyrene foams for insulation in the construction industry. Most of these products will become a part of the construction and demolition (C&D) waste at the end of their life cycle (30-50 years) which is typically disposed of into landfills or incineration. However, the recycling of this material takes quite a low share compared with landfill and incineration. Consequently, high environmental risks will exist in these disposal approaches due to the HBCDD in C&D waste. Currently, XPS or EPS products containing HBCDD in the construction industry have not reached the end of their life cycle in most countries. Relatively little attention has been paid to this emergency issue by either the government or public. Furthermore, C&D waste is most likely disposed of by direct dumping, simple stacking, or open burning in developing countries. Therefore, this paper highlights the global environmental risks of HBCDD from C&D waste. Areas of research for key problems of HBCDD contained in C&D waste are suggested to help control and finally eliminate the impact.

Development of construction materials using nano-silica and aggregates recycled from construction and demolition waste.

Science.gov (United States)

Mukharjee, Bibhuti Bhusan; Barai, Sudhirkumar V

2015-06-01

The present work addresses the development of novel construction materials utilising commercial grade nano-silica and recycled aggregates retrieved from construction and demolition waste. For this, experimental work has been carried out to examine the influence of nano-silica and recycled aggregates on compressive strength, modulus of elasticity, water absorption, density and volume of voids of concrete. Fully natural and recycled aggregate concrete mixes are designed by replacing cement with three levels (0.75%, 1.5% and 3%) of nano-silica. The results of the present investigation depict that improvement in early days compressive strength is achieved with the incorporation of nano-silica in addition to the restoration of reduction in compressive strength of recycled aggregate concrete mixes caused owing to the replacement of natural aggregates by recycled aggregates. Moreover, the increase in water absorption and volume of voids with a reduction of bulk density was detected with the incorporation of recycled aggregates in place of natural aggregates. However, enhancement in density and reduction in water absorption and volume of voids of recycled aggregate concrete resulted from the addition of nano-silica. In addition, the results of the study reveal that nano-silica has no significant effect on elastic modulus of concrete. © The Author(s) 2015.

A web-based Decision Support System for the optimal management of construction and demolition waste.

Science.gov (United States)

Banias, G; Achillas, Ch; Vlachokostas, Ch; Moussiopoulos, N; Papaioannou, I

2011-12-01

Wastes from construction activities constitute nowadays the largest by quantity fraction of solid wastes in urban areas. In addition, it is widely accepted that the particular waste stream contains hazardous materials, such as insulating materials, plastic frames of doors, windows, etc. Their uncontrolled disposal result to long-term pollution costs, resource overuse and wasted energy. Within the framework of the DEWAM project, a web-based Decision Support System (DSS) application - namely DeconRCM - has been developed, aiming towards the identification of the optimal construction and demolition waste (CDW) management strategy that minimises end-of-life costs and maximises the recovery of salvaged building materials. This paper addresses both technical and functional structure of the developed web-based application. The web-based DSS provides an accurate estimation of the generated CDW quantities of twenty-one different waste streams (e.g. concrete, bricks, glass, etc.) for four different types of buildings (residential, office, commercial and industrial). With the use of mathematical programming, the DeconRCM provides also the user with the optimal end-of-life management alternative, taking into consideration both economic and environmental criteria. The DSS's capabilities are illustrated through a real world case study of a typical five floor apartment building in Thessaloniki, Greece. Copyright © 2011 Elsevier Ltd. All rights reserved.

An empirical investigation of construction and demolition waste generation rates in Shenzhen city, South China

International Nuclear Information System (INIS)

Lu Weisheng; Yuan Hongping; Li Jingru; Hao, Jane J.L.; Mi Xuming; Ding Zhikun

2011-01-01

The construction and demolition waste generation rates (C and D WGRs) is an important factor in decision-making and management of material waste in any construction site. The present study investigated WGRs by conducting on-site waste sorting and weighing in four ongoing construction projects in Shenzhen city of South China. The results revealed that WGRs ranged from 3.275 to 8.791 kg/m 2 and miscellaneous waste, timber for formwork and falsework, and concrete were the three largest components amongst the generated waste. Based on the WGRs derived from the research, the paper also discussed the main causes of waste in the construction industry and attempted to connect waste generation with specific construction practices. It was recommended that measures mainly including performing waste sorting at source, employing skilful workers, uploading and storing materials properly, promoting waste management capacity, replacing current timber formwork with metal formwork and launching an incentive reward program to encourage waste reduction could be potential solutions to reducing current WGRs in Shenzhen. Although these results were derived from a relatively small sample and so cannot justifiably be generalized, they do however add to the body of knowledge that is currently available for understanding the status of the art of C and D waste management in China.

A bi-level environmental impact assessment framework for comparing construction and demolition waste management strategies.

Science.gov (United States)

Yazdanbakhsh, Ardavan

2018-04-27

Several pioneering life cycle assessment (LCA) studies have been conducted in the past to assess the environmental impact of specific methods for managing mineral construction and demolition waste (MCDW), such as recycling the waste for use in concrete. Those studies focus on comparing the use of recycled MCDW and that of virgin components to produce materials or systems that serve specified functions. Often, the approaches adopted by the studies do not account for the potential environmental consequence of avoiding the existing or alternative waste management practices. The present work focuses on how product systems need to be defined in recycling LCA studies and what processes need to be within the system boundaries. A bi-level LCA framework is presented for modelling alternative waste management approaches in which the impacts are measured and compared at two scales of strategy and decision-making. Different functional units are defined for each level, all of which correspond to the same flow of MCDW in a cascade of product systems. For the sole purpose of demonstrating how the framework is implemented an illustrative example is presented, based on real data and a number of simplifying assumptions, which compares the impacts of a number of potential MCDW management strategies in New York City. Copyright © 2018 Elsevier Ltd. All rights reserved.

Superradiators created atom by atom

Science.gov (United States)

Meschede, Dieter

2018-02-01

High radiation rates are usually associated with macroscopic lasers. Laser radiation is “coherent”—its amplitude and phase are well-defined—but its generation requires energy inputs to overcome loss. Excited atoms spontaneously emit in a random and incoherent fashion, and for N such atoms, the emission rate simply increases as N. However, if these atoms are in close proximity and coherently coupled by a radiation field, this microscopic ensemble acts as a single emitter whose emission rate increases as N2 and becomes “superradiant,” to use Dicke's terminology (1). On page 662 of this issue, Kim et al. (2) show the buildup of coherent light fields through collective emission from atomic radiators injected one by one into a resonator field. There is only one atom ever in the cavity, but the emission is still collective and superradiant. These results suggest another route toward thresholdless lasing.

New sources of cold atoms for atomic clocks

International Nuclear Information System (INIS)

Aucouturier, E.

1997-01-01

The purpose of this doctoral work is the realisation of new sources of cold cesium atoms that could be useful for the conception of a compact and high-performance atomic clock. It is based on experiences of atomic physics using light induced atomic manipulation. We present here the experiences of radiative cooling of atoms that have been realised at the Laboratoire de l'Horloge Atomique from 1993 to 1996. Firstly, we applied the techniques of radiative cooling and trapping of atoms in order to create a three-dimensional magneto-optical trap. For this first experience, we developed high quality laser sources, that were used for other experiments. We imagined a new configuration of trapping (two-dimensional magneto-optical trap) that was the basis for a cold atom source. This design gives the atoms a possibility to escape towards one particular direction. Then, we have extracted the atoms from this anisotropic trap in order to create a continuous beam of cold atoms. We have applied three methods of extraction. Firstly, the launching of atoms was performed by reducing the intensity of one of the cooling laser beams in the desired launching direction. Secondly, a frequency detuning between the two laser laser beams produced the launching of atoms by a so-called 'moving molasses'. The third method consisted in applying a static magnetic field that induced the launching of atoms in the direction of this magnetic field. At the same time, another research on cold atoms was initiated at the I.H.A. It consisted in cooling a large volume of atoms from a cell, using an isotropic light. This offers an interesting alternative to the traditional optical molasses. (author)

2007 Global Demilitarization Symposium and Exhibition

Science.gov (United States)

2007-05-17

Directorate Design Development - Cryofracture Subsystem - • Munitions Preparation Trailer – Munition loading fixtures to ensure proper orientation – Conveyor ...in cryobath – Empty fixture return heater – Conveyor to transfer munitions to Cryofracture Press Trailer • Cryofracture Press Trailer – 3.0 lbs. (TNT...diverters to separate fracture munitions into four feed chutes – Press munitions loader robot to transfer munitions to press Energetics, Warheads

Atom interferometry with trapped Bose-Einstein condensates: impact of atom-atom interactions

International Nuclear Information System (INIS)

Grond, Julian; Hohenester, Ulrich; Mazets, Igor; Schmiedmayer, Joerg

2010-01-01

Interferometry with ultracold atoms promises the possibility of ultraprecise and ultrasensitive measurements in many fields of physics, and is the basis of our most precise atomic clocks. Key to a high sensitivity is the possibility to achieve long measurement times and precise readout. Ultracold atoms can be precisely manipulated at the quantum level and can be held for very long times in traps; they would therefore be an ideal setting for interferometry. In this paper, we discuss how the nonlinearities from atom-atom interactions, on the one hand, allow us to efficiently produce squeezed states for enhanced readout and, on the other hand, result in phase diffusion that limits the phase accumulation time. We find that low-dimensional geometries are favorable, with two-dimensional (2D) settings giving the smallest contribution of phase diffusion caused by atom-atom interactions. Even for time sequences generated by optimal control, the achievable minimal detectable interaction energy ΔE min is of the order of 10 -4 μ, where μ is the chemical potential of the Bose-Einstein condensate (BEC) in the trap. From these we have to conclude that for more precise measurements with atom interferometers, more sophisticated strategies, or turning off the interaction-induced dephasing during the phase accumulation stage, will be necessary.

Atom-atom collision cascades localization

International Nuclear Information System (INIS)

Kirsanov, V.V.

1980-01-01

The presence of an impurity and thermal vibration influence on the atom-atom collision cascade development is analysed by the computer simulation method (the modificated dynamic model). It is discovered that the relatively low energetic cascades are localized with the temperature increase of an irradiated crystal. On the basis of the given effect the mechanism of splitting of the high energetic cascades into subcascades is proposed. It accounts for two factors: the primary knocked atom energy and the irradiated crystal temperature. Introduction of an impurity also localizes the cascades independently from the impurity atom mass. The cascades localization leads to intensification of the process of annealing in the cascades and reduction of the post-cascade vacancy cluster sizes. (author)

Benthic communities in chemical munitions dumping site areas within the Baltic deeps with special focus on nematodes

Science.gov (United States)

Kotwicki, Lech; Grzelak, Katarzyna; Bełdowski, Jacek

2016-06-01

Assessment of biological effects of chemical warfare agents (CWAs) dumped in the Baltic Sea has been one of the tasks of the Chemical Munitions Search & Assessment (CHEMSEA) project. Three sites have been selected for investigation: Bornholm Deep, Gotland Deep and Gdansk Deep. Fauna collected from these locations were compared with the reference area located between the studied regions at similar depths below 70 m. In total, four scientific cruises occurred in different seasons between 2011 and 2013. The total lack of any representatives of macrozoobenthos in all of the investigated dumping sites was noted. As a practical matter, the Baltic deeps were inhabited by nematodes as the only meiofauna representatives. Therefore, nematodes were used as a key group to explore the faunal communities inhabiting chemical dumping sites in the Baltic deeps. In total, 42 nematode genera belonging to 18 families were identified, and the dominant genus was Sabatieria (Comesomatidae), which constituted 37.6% of the overall nematode community. There were significant differences in nematode community structure (abundance and taxa composition) between the dumping areas and the reference site (Kruskal-Wallis H=30.96, pnematode assemblages could mirror the environmental conditions.

Code ATOM for calculation of atomic characteristics

International Nuclear Information System (INIS)

Vainshtein, L.A.

1990-01-01

In applying atomic physics to problems of plasma diagnostics, it is necessary to determine some atomic characteristics, including energies and transition probabilities, for very many atoms and ions. Development of general codes for calculation of many types of atomic characteristics has been based on general but comparatively simple approximate methods. The program ATOM represents an attempt at effective use of such a general code. This report gives a brief description of the methods used, and the possibilities of and limitations to the code are discussed. Characteristics of the following processes can be calculated by ATOM: radiative transitions between discrete levels, radiative ionization and recombination, collisional excitation and ionization by electron impact, collisional excitation and ionization by point heavy particle (Born approximation only), dielectronic recombination, and autoionization. ATOM explores Born (for z=1) or Coulomb-Born (for z>1) approximations. In both cases exchange and normalization can be included. (N.K.)

Atomic physics

International Nuclear Information System (INIS)

Armbruster, P.; Beyer, H.; Bosch, F.; Dohmann, H.D.; Kozhuharov, C.; Liesen, D.; Mann, R.; Mokler, P.H.

1984-01-01

The heavy ion accelerator UNILAC is well suited to experiments in the field of atomic physics because, with the aid of high-energy heavy ions atoms can be produced in exotic states - that is, heavy atoms with only a few electrons. Also, in close collisions of heavy ions (atomic number Z 1 ) and heavy target atoms (Z 2 ) short-lived quasi-atomic 'superheavy' systems will be formed - huge 'atoms', where the inner electrons are bound in the field of the combined charge Z 1 + Z 2 , which exceeds by far the charge of the known elements (Z <= 109). Those exotic or transient superheavy atoms delivered from the heavy ion accelerator make it possible to study for the first time in a terrestrial laboratory exotic, but fundamental, processes, which occur only inside stars. Some of the basic research carried out with the UNILAC is discussed. This includes investigation of highly charged heavy atoms with the beam-foil method, the spectroscopy of highly charged slow-recoil ions, atomic collision studies with highly ionised, decelerated ions and investigations of super-heavy quasi-atoms. (U.K.)

Formulation development and characterization of cellulose acetate nitrate based propellants for improved insensitive munitions properties

Directory of Open Access Journals (Sweden)

Thelma Manning

2014-06-01

Full Text Available Cellulose acetate nitrate (CAN was used as an insensitive energetic binder to improve the insensitive munitions (IM properties of gun propellants to replace the M1 propellant used in 105 mm artillery charges. CAN contains the energetic nitro groups found in nitrocellulose (NC, but also acetyl functionalities, which lowered the polymer's sensitivity to heat and shock, and therefore improved its IM properties relative to NC. The formulation, development and small-scale characterization testing of several CAN-based propellants were done. The formulations, using insensitive energetic solid fillers and high-nitrogen modifiers in place of nitramine were completed. The small scale characterization testing, such as closed bomb testing, small scale sensitivity, thermal stability, and chemical compatibility were done. The mechanical response of the propellants under high-rate uni-axial compression at, hot, cold, and ambient temperatures were also completed. Critical diameter testing, hot fragment conductive ignition (HFCI tests were done to evaluate the propellants' responses to thermal and shock stimuli. Utilizing the propellant chemical composition, theoretical predictions of erosivity were completed. All the small scale test results were utilized to down-select the promising CAN based formulations for large scale demonstration testing such as the ballistic performance and fragment impact testing in the 105 mm M67 artillery charge configurations. The test results completed in the small and large scale testing are discussed.

Of Ashes and Atoms

Science.gov (United States)

2005-01-01

This feature length DVD documentary, reviews the history of the Plum Brook Nuclear Reactor from the initial settlers of the area, through its use as a munitions facility during the second World War to the development of the nuclear facility and its use as one of the first nuclear test reactors built in the United States, and the only one built by NASA. It concludes with the beginning of the decommissioning of the facility. There is a brief review of the reactor design, and its workings. Through discussions with the NASA engineers and operators of the facility, the film reviews the work done to advance the knowledge of the effects of radiation, the properties of radiated materials, and the work to advance the state of the art in nuclear propulsion. The film shows footage of public tours, and shows actual footage of the facility in operation, and after its shutdown in 1973. The DVD was narrated by Kate Mulgrew, who leads the viewer through the history of the facility to its eventual ongoing decommissioning, and return to the state of pastoral uses.

Atom optics

International Nuclear Information System (INIS)

Balykin, V. I.; Jhe, W.

1999-01-01

Atom optics, in analogy to neutron and electron optics, deals with the realization of as a traditional elements, such as lenes, mirrors, beam splitters and atom interferometers, as well as a new 'dissipative' elements such as a slower and a cooler, which have no analogy in an another types of optics. Atom optics made the development of atom interferometer with high sensitivity for measurement of acceleration and rotational possible. The practical interest in atom optics lies in the opportunities to create atom microprobe with atom-size resolution and minimum damage of investigated objects. (Cho, G. S.)

Biological sulfate removal from construction and demolition debris leachate: Effect of bioreactor configuration

Energy Technology Data Exchange (ETDEWEB)

Kijjanapanich, Pimluck, E-mail: som_cheng00@hotmail.com [Pollution Prevention and Resource Recovery Chair Group, UNESCO-IHE Institute for Water Education, Westvest 7, 2611 AX Delft (Netherlands); Do, Anh Tien [Civil and Environmental Engineering, University of South Florida, Tampa, FL 33620 (United States); Annachhatre, Ajit P. [Environmental Engineering and Management, Asian Institute of Technology, PO Box 4, Klongluang, Pathumthani 12120 (Thailand); Esposito, Giovanni [Department of Civil and Mechanical Engineering, University of Cassino and Southern Lazio, Via Di Biasio 43, 03043 Cassino (Italy); Yeh, Daniel H. [Civil and Environmental Engineering, University of South Florida, Tampa, FL 33620 (United States); Lens, Piet N.L. [Pollution Prevention and Resource Recovery Chair Group, UNESCO-IHE Institute for Water Education, Westvest 7, 2611 AX Delft (Netherlands)

2014-03-01

Highlights: • Novel biological technique for gypsum removal from CDD. • CDDS leachate treatment performed using different sulfate reducing bioreactors. • Gypsum in CDD can be used as a source of sulfate for sulfate reducing bacteria. • High calcium concentration (1000 mg L{sup −1}) did not affect the bioreactor performance. - Abstract: Due to the contamination of construction and demolition debris (CDD) by gypsum drywall, especially, its sand fraction (CDD sand, CDDS), the sulfate content in CDDS exceeds the posed limit of the maximum amount of sulfate present in building sand (1.73 g sulfate per kg of sand for the Netherlands). Therefore, the CDDS cannot be reused for construction. The CDDS has to be washed in order to remove most of the impurities and to obtain the right sulfate content, thus generating a leachate, containing high sulfate and calcium concentrations. This study aimed at developing a biological sulfate reduction system for CDDS leachate treatment and compared three different reactor configurations for the sulfate reduction step: the upflow anaerobic sludge blanket (UASB) reactor, inverse fluidized bed (IFB) reactor and gas lift anaerobic membrane bioreactor (GL-AnMBR). This investigation demonstrated that all three systems can be applied for the treatment of CDDS leachate. The highest sulfate removal efficiency of 75–85% was achieved at a hydraulic retention time (HRT) of 15.5 h. A high calcium concentration up to 1000 mg L{sup −1} did not give any adverse effect on the sulfate removal efficiency of the IFB and GL-AnMBR systems.

Biological sulfate removal from construction and demolition debris leachate: Effect of bioreactor configuration

International Nuclear Information System (INIS)

Kijjanapanich, Pimluck; Do, Anh Tien; Annachhatre, Ajit P.; Esposito, Giovanni; Yeh, Daniel H.; Lens, Piet N.L.

2014-01-01

Highlights: • Novel biological technique for gypsum removal from CDD. • CDDS leachate treatment performed using different sulfate reducing bioreactors. • Gypsum in CDD can be used as a source of sulfate for sulfate reducing bacteria. • High calcium concentration (1000 mg L −1 ) did not affect the bioreactor performance. - Abstract: Due to the contamination of construction and demolition debris (CDD) by gypsum drywall, especially, its sand fraction (CDD sand, CDDS), the sulfate content in CDDS exceeds the posed limit of the maximum amount of sulfate present in building sand (1.73 g sulfate per kg of sand for the Netherlands). Therefore, the CDDS cannot be reused for construction. The CDDS has to be washed in order to remove most of the impurities and to obtain the right sulfate content, thus generating a leachate, containing high sulfate and calcium concentrations. This study aimed at developing a biological sulfate reduction system for CDDS leachate treatment and compared three different reactor configurations for the sulfate reduction step: the upflow anaerobic sludge blanket (UASB) reactor, inverse fluidized bed (IFB) reactor and gas lift anaerobic membrane bioreactor (GL-AnMBR). This investigation demonstrated that all three systems can be applied for the treatment of CDDS leachate. The highest sulfate removal efficiency of 75–85% was achieved at a hydraulic retention time (HRT) of 15.5 h. A high calcium concentration up to 1000 mg L −1 did not give any adverse effect on the sulfate removal efficiency of the IFB and GL-AnMBR systems

Directed Atom-by-Atom Assembly of Dopants in Silicon.

Science.gov (United States)

Hudak, Bethany M; Song, Jiaming; Sims, Hunter; Troparevsky, M Claudia; Humble, Travis S; Pantelides, Sokrates T; Snijders, Paul C; Lupini, Andrew R

2018-05-17

The ability to controllably position single atoms inside materials is key for the ultimate fabrication of devices with functionalities governed by atomic-scale properties. Single bismuth dopant atoms in silicon provide an ideal case study in view of proposals for single-dopant quantum bits. However, bismuth is the least soluble pnictogen in silicon, meaning that the dopant atoms tend to migrate out of position during sample growth. Here, we demonstrate epitaxial growth of thin silicon films doped with bismuth. We use atomic-resolution aberration-corrected imaging to view the as-grown dopant distribution and then to controllably position single dopants inside the film. Atomic-scale quantum-mechanical calculations corroborate the experimental findings. These results indicate that the scanning transmission electron microscope is of particular interest for assembling functional materials atom-by-atom because it offers both real-time monitoring and atom manipulation. We envision electron-beam manipulation of atoms inside materials as an achievable route to controllable assembly of structures of individual dopants.

Atomic weight versus atomic mass controversy

International Nuclear Information System (INIS)

Holden, N.E.

1985-01-01

A problem for the Atomic Weights Commission for the past decade has been the controversial battle over the names ''atomic weight'' and ''atomic mass''. The Commission has considered the arguments on both sides over the years and it appears that this meeting will see more of the same discussion taking place. In this paper, I review the situation and offer some alternatives

Angular momentum coupling in atom-atom collisions

International Nuclear Information System (INIS)

Grosser, J.

1986-01-01

The coupling between the electronic angular momentum and the rotating atom-atom axis in the initial or the final phase of an atom-atom collision is discussed, making use of the concepts of radial and rotational (Coriolis) coupling between different molecular states. The description is based on a limited number of well-understood approximations, and it allows an illustrative geometric representation of the transition from the body fixed to the space fixed motion of the electrons. (orig.)

Investigating the determinants of contractor's construction and demolition waste management behavior in Mainland China.

Science.gov (United States)

Wu, Zezhou; Yu, Ann T W; Shen, Liyin

2017-02-01

The abundant generation of construction and demolition (C&D) waste presents a significant challenge to the sustainable development of the construction industry in Mainland China. As the implementer of construction activities, the contractor's C&D waste management performance plays an important role in C&D waste minimization. This paper aims to investigate the determinants of the contractor's C&D waste management behavior in Mainland China. The Theory of Planned Behavior (TPB) was selected as the basis of the theoretical model. In addition, three contextual constructs (i.e., economic viability, governmental supervision, and project constraints) were introduced, formulating the initial model. Based on the initial model, eight constructs were identified and seven hypotheses were proposed. A questionnaire survey was conducted to collect data and a Structural Equation Modeling (SEM) analysis was employed to test the proposed hypotheses. Results showed that the C&D waste management intention is not a significant determinant of contractor's C&D waste management behavior. The most important determinant is economic viability, followed by governmental supervision as the second most important determinant. Nevertheless, the construct of project constraints is an insignificant determinant for contractor's adoption of C&D waste management behavior. The research findings imply that, in Mainland China, the government, at this stage, plays an important role in guiding and promoting the contractor to exhibit better C&D waste management behavior. Copyright © 2016 Elsevier Ltd. All rights reserved.

Mobilization of iron and arsenic from soil by construction and demolition debris landfill leachate.

Science.gov (United States)

Wang, Yu; Sikora, Saraya; Kim, Hwidong; Dubey, Brajesh; Townsend, Timothy

2012-05-01

Column experiments were performed to examine (a) the potential for leachate from construction and demolition (C&D) debris landfills to mobilize naturally-occurring iron and arsenic from soils underlying such facilities and (b) the ability of crushed limestone to remove these aqueous phase pollutants. In duplicate columns, water was added to a 30-cm layer of synthetic C&D debris, with the resulting leachate serially passed through a 30-cm soil layer containing iron and arsenic and a 30-cm crushed limestone layer. This experiment was conducted for two different soil types (one high in iron (10,400mg/kg) and the second high in iron (5400mg/kg) and arsenic (70mg/kg)); also monitored were control columns for both soil types with water infiltration alone. Despite low iron concentrations in the simulated C&D debris leachate, elevated iron concentrations were observed when leachate passed through the soils; reductive dissolution was concluded to be the cause of iron mobilization. In the soil containing elevated arsenic, increased iron mobilization from the soil was accompanied by a similar but delayed arsenic mobilization. Since arsenic sorbs to oxidized iron soil minerals, reductive dissolution of these minerals results in arsenic mobilization. Crushed limestone significantly reduced iron (to values below the detection limit of 0.01mg/L in most cases); however, arsenic was not removed to any significant extent. Copyright © 2011 Elsevier Ltd. All rights reserved.

Development of a hybrid model to predict construction and demolition waste: China as a case study.

Science.gov (United States)

Song, Yiliao; Wang, Yong; Liu, Feng; Zhang, Yixin

2017-01-01

Construction and demolition waste (C&DW) is currently a worldwide issue, and the situation is the worst in China due to a rapid increase in the construction industry and the short life span of China's buildings. To create an opportunity out of this problem, comprehensive prevention measures and effective management strategies are urgently needed. One major gap in the literature of waste management is a lack of estimations on future C&DW generation. Therefore, this paper presents a forecasting procedure for C&DW in China that can forecast the quantity of each component in such waste. The proposed approach is based on a GM-SVR model that improves the forecasting effectiveness of the gray model (GM), which is achieved by adjusting the residual series by a support vector regression (SVR) method and a transition matrix that aims to estimate the discharge of each component in the C&DW. Through the proposed method, future C&DW volume are listed and analyzed containing their potential components and distribution in different provinces in China. Besides, model testing process provides mathematical evidence to validate the proposed model is an effective way to give future information of C&DW for policy makers. Copyright © 2016 Elsevier Ltd. All rights reserved.

Cavity Exciton-Polariton mediated, Single-Shot Quantum Non-Demolition measurement of a Quantum Dot Electron Spin

Science.gov (United States)

Puri, Shruti; McMahon, Peter; Yamamoto, Yoshihisa

2014-03-01

The quantum non-demolition (QND) measurement of a single electron spin is of great importance in measurement-based quantum computing schemes. The current single-shot readout demonstrations exhibit substantial spin-flip backaction. We propose a QND readout scheme for quantum dot (QD) electron spins in Faraday geometry, which differs from previous proposals and implementations in that it relies on a novel physical mechanism: the spin-dependent Coulomb exchange interaction between a QD spin and optically-excited quantum well (QW) microcavity exciton-polaritons. The Coulomb exchange interaction causes a spin-dependent shift in the resonance energy of the polarized polaritons, thus causing the phase and intensity response of left circularly polarized light to be different to that of the right circularly polarized light. As a result the QD electron's spin can be inferred from the response to a linearly polarized probe. We show that by a careful design of the system, any spin-flip backaction can be eliminated and a QND measurement of the QD electron spin can be performed within a few 10's of nanoseconds with fidelity 99:95%. This improves upon current optical QD spin readout techniques across multiple metrics, including fidelity, speed and scalability. National Institute of Informatics, 2-1-2 Hitotsubashi, Chiyoda-ku, Tokyo 101-8430, Japan.

An empirical investigation of construction and demolition waste generation rates in Shenzhen city, South China.

Science.gov (United States)

Lu, Weisheng; Yuan, Hongping; Li, Jingru; Hao, Jane J L; Mi, Xuming; Ding, Zhikun

2011-04-01

The construction and demolition waste generation rates (C&D WGRs) is an important factor in decision-making and management of material waste in any construction site. The present study investigated WGRs by conducting on-site waste sorting and weighing in four ongoing construction projects in Shenzhen city of South China. The results revealed that WGRs ranged from 3.275 to 8.791 kg/m(2) and miscellaneous waste, timber for formwork and falsework, and concrete were the three largest components amongst the generated waste. Based on the WGRs derived from the research, the paper also discussed the main causes of waste in the construction industry and attempted to connect waste generation with specific construction practices. It was recommended that measures mainly including performing waste sorting at source, employing skilful workers, uploading and storing materials properly, promoting waste management capacity, replacing current timber formwork with metal formwork and launching an incentive reward program to encourage waste reduction could be potential solutions to reducing current WGRs in Shenzhen. Although these results were derived from a relatively small sample and so cannot justifiably be generalized, they do however add to the body of knowledge that is currently available for understanding the status of the art of C&D waste management in China. Copyright © 2010 Elsevier Ltd. All rights reserved.

Life cycle assessment of construction and demolition waste management

International Nuclear Information System (INIS)

Butera, Stefania; Christensen, Thomas H.; Astrup, Thomas F.

2015-01-01

Highlights: • LCA of C&DW utilisation in road vs. C&DW landfilling. • C&DW utilisation in road better than landfilling for most categories. • Transportation is the most important process in non-toxic impact categories. • Leaching of oxyanions is the critical process in toxic impact categories. • Modelling of Cr fate in the subsoil is highly influential to the results. - Abstract: Life cycle assessment (LCA) modelling of construction and demolition waste (C&DW) management was carried out. The functional unit was management of 1 Mg mineral, source separated C&DW, which is either utilised in road construction as a substitute for natural aggregates, or landfilled. The assessed environmental impacts included both non-toxic and toxic impact categories. The scenarios comprised all stages of the end-of-life management of C&DW, until final disposal of all residues. Leaching of inorganic contaminants was included, as was the production of natural aggregates, which was avoided because of the use of C&DW. Typical uncertainties related to contaminant leaching were addressed. For most impact categories, utilisation of C&DW in road construction was preferable to landfilling; however, for most categories, utilisation resulted in net environmental burdens. Transportation represented the most important contribution for most nontoxic impacts, accounting for 60–95 per cent of these impacts. Capital goods contributed with negligible impacts. Leaching played a critical role for the toxic categories, where landfilling had lower impacts than utilisation because of the lower levels of leachate per ton of C&DW reaching the groundwater over a 100-year perspective. Leaching of oxyanions (As, V and Sb) was critical with respect to leaching. Typical experimental uncertainties in leaching data did not have a pivotal influence on the results; however, accounting for Cr immobilisation in soils as part of the impact assessment was critical for modelling the leaching impacts. Compared

Life cycle assessment of construction and demolition waste management

Energy Technology Data Exchange (ETDEWEB)

Butera, Stefania, E-mail: stbu@teknologisk.dk; Christensen, Thomas H.; Astrup, Thomas F.

2015-10-15

Highlights: • LCA of C&DW utilisation in road vs. C&DW landfilling. • C&DW utilisation in road better than landfilling for most categories. • Transportation is the most important process in non-toxic impact categories. • Leaching of oxyanions is the critical process in toxic impact categories. • Modelling of Cr fate in the subsoil is highly influential to the results. - Abstract: Life cycle assessment (LCA) modelling of construction and demolition waste (C&DW) management was carried out. The functional unit was management of 1 Mg mineral, source separated C&DW, which is either utilised in road construction as a substitute for natural aggregates, or landfilled. The assessed environmental impacts included both non-toxic and toxic impact categories. The scenarios comprised all stages of the end-of-life management of C&DW, until final disposal of all residues. Leaching of inorganic contaminants was included, as was the production of natural aggregates, which was avoided because of the use of C&DW. Typical uncertainties related to contaminant leaching were addressed. For most impact categories, utilisation of C&DW in road construction was preferable to landfilling; however, for most categories, utilisation resulted in net environmental burdens. Transportation represented the most important contribution for most nontoxic impacts, accounting for 60–95 per cent of these impacts. Capital goods contributed with negligible impacts. Leaching played a critical role for the toxic categories, where landfilling had lower impacts than utilisation because of the lower levels of leachate per ton of C&DW reaching the groundwater over a 100-year perspective. Leaching of oxyanions (As, V and Sb) was critical with respect to leaching. Typical experimental uncertainties in leaching data did not have a pivotal influence on the results; however, accounting for Cr immobilisation in soils as part of the impact assessment was critical for modelling the leaching impacts. Compared

Co-composting of Beef Cattle Feedlot Manure with Construction and Demolition Waste.

Science.gov (United States)

Hao, Xiying; Hill, Brett; Caffyn, Pam; Travis, Greg; Olson, Andrew F; Larney, Francis J; McAllister, Tim; Alexander, Trevor

2014-09-01

With increased availability of dried distillers' grains with solubles (DDGS) as cattle feed and the need to recycle organic wastes, this research investigated the feasibility of co-composting DDGS cattle feedlot manure with construction and demolition (C&D) waste. Manure was collected from cattle fed a typical western Canadian finishing diet (CK) of 860 g rolled barley ( L.) grain, 100 g barley silage, and 40 g vitamin and mineral supplement kg dry matter (DM) and from cattle fed the same diet but (DG manure) with 300 g kg DM barley grain being replaced by DDGS. The CK and DG manures were co-composted with and without C&D waste in 13 m bins. Compost materials were turned on Days 14, 37, and 64, and terminated on Day 99. Adding C&D waste led to higher compost temperatures (0.4 to 16.3°C, average 7.2°C) than manure alone. Final composts had similar total C, total N, C/N ratios, and water-extractable K, Mg, and NO content across all treatments. However, adding C&D waste increased δC, δN, water-extractable SO, and Ca contents and decreased pH, total P (TP), water-extractable C, N, and P and most volatile fatty acids (VFA). The higher C&D compost temperatures should reduce pathogens while reduced VFA content should reduce odors. When using the final compost product, the increased SO and reduced TP and available N and P content in C&D waste compost should be taken into consideration. Increased S content in C&D compost may be beneficial for some crops grown on S-deficient soils. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

Assessment of Energetic Compounds, Semi-volatile Organic Compounds, and Trace Elements in Streambed Sediment and Stream Water from Streams Draining Munitions Firing Points and Impact Areas, Fort Riley, Kansas, 2007-08

Science.gov (United States)

Coiner, R.L.; Pope, L.M.; Mehl, H.E.

2010-01-01

An assessment of energetic compounds (explosive and propellant residues) and associated semi-volatile organic compounds (SVOCs) and trace elements in streambed sediment and stream water from streams draining munitions firing points and impact areas at Fort Riley, northeast Kansas, was performed during 2007-08 by the U.S. Geological Survey (USGS) in cooperation with the U.S. Army. Streambed sediment from 16 sampling sites and stream-water samples from 5 sites were collected at or near Fort Riley and analyzed for as many as 17 energetic compounds, 65 SVOCs, and 27 trace elements. None of the energetic compounds or SVOCs were detected in streambed sediment collected from sites within the Fort Riley Military Reservation. This may indicate that these compounds either are not transported from dispersal areas or that analytical methods are not sensitive enough to detect the small concentrations that may be transported. Concentrations of munitions-associated trace elements did not exceed sediment-quality guidelines recommended by the U.S. Environmental Protection Agency (USEPA) and are not indicative of contamination of streambed sediment at selected streambed sampling sites, at least in regards to movement from dispersal areas. Analytical results of stream-water samples provided little evidence of contamination by energetic compounds, SVOCs, or associated trace elements. Perchlorate was detected in 19 of 20 stream-water samples at concentrations ranging from an estimated 0.057 to an estimated 0.236 ug/L (micrograms per liter) with a median concentration of an estimated 0.114 ug/L, substantially less than the USEPA Interim Health Advisory criterion (15 ug/L), and is in the range of documented background concentrations. Because of these small concentrations and possible natural sources (precipitation and groundwater), it is likely that the occurrence of perchlorate in stream water is naturally occurring, although a definitive identification of the source of perchlorate in

Sub-Angstrom Atomic-Resolution Imaging of Heavy Atoms to Light Atoms

Energy Technology Data Exchange (ETDEWEB)

O' Keefe, Michael A.; Shao-Horn, Yang

2003-05-23

Three decades ago John Cowley and his group at ASU achieved high-resolution electron microscope images showing the crystal unit cell contents at better than 4Angstrom resolution. Over the years, this achievement has inspired improvements in resolution that have enabled researchers to pinpoint the positions of heavy atom columns within the cell. More recently, this ability has been extended to light atoms as resolution has improved. Sub-Angstrom resolution has enabled researchers to image the columns of light atoms (carbon, oxygen and nitrogen) that are present in many complex structures. By using sub-Angstrom focal-series reconstruction of the specimen exit surface wave to image columns of cobalt, oxygen, and lithium atoms in a transition metal oxide structure commonly used as positive electrodes in lithium rechargeable batteries, we show that the range of detectable light atoms extends to lithium. HRTEM at sub-Angstrom resolution will provide the essential role of experimental verification for the emergent nanotech revolution. Our results foreshadow those to be expected from next-generation TEMs with Cs-corrected lenses and monochromated electron beams.

Atomic absorption spectrometry using tungsten and molybdenum tubes as metal atomizer

International Nuclear Information System (INIS)

Kaneco, Satoshi; Katsumata, Hideyuki; Ohta, Kiyohisa; Suzuki, Tohru

2007-01-01

We have developed a metal tube atomizer for the electrothermal atomization atomic absorption spectrometry (ETA-AAS). Tungsten, molybdenum, platinum tube atomizers were used as the metal atomizer for ETA-AAS. The atomization characteristics of various metals using these metal tube atomizers were investigated. The effects of heating rate of atomizer, atomization temperature, pyrolysis temperature, argon purge gas flow rate and hydrogen addition on the atomic absorption signal were investigated for the evaluation of atomization characteristics. Moreover, ETA-AAS with metal tube atomizer has been combined with the slurry-sampling techniques. Ultrasonic slurry-sampling ETA-AAS with metal tube atomizer were effective for the determination of trace metal elements in biological materials, calcium drug samples, herbal medicine samples, vegetable samples and fish samples. Furthermore, a preconcentration method of trace metals involving adsorption on a metal wire has been applied to ETA-AAS with metal tube atomizer. (author)

Atom chips: mesoscopic physics with cold atoms

International Nuclear Information System (INIS)

Krueger, P.; Wildermuth, S.; Hofferberth, S.; Haller, E.; GAllego Garcia, D.; Schmiedmayer, J.

2005-01-01

Full text: Cold neutral atoms can be controlled and manipulated in microscopic potentials near surfaces of atom chips. These integrated micro-devices combine the known techniques of atom optics with the capabilities of well established micro- and nanofabrication technology. In analogy to electronic microchips and integrated fiber optics, the concept of atom chips is suitable to explore the domain of mesoscopic physics with matter waves. We use current and charge carrying structures to form complex potentials with high spatial resolution only microns from the surface. In particular, atoms can be confined to an essentially one-dimensional motion. In this talk, we will give an overview of our experiments studying the manipulation of both thermal atoms and BECs on atom chips. First experiments in the quasi one-dimensional regime will be presented. These experiments profit from strongly reduced residual disorder potentials caused by imperfections of the chip fabrication with respect to previously published experiments. This is due to our purely lithographic fabrication technique that proves to be advantageous over electroplating. We have used one dimensionally confined BECs as an ultra-sensitive probe to characterize these potentials. These smooth potentials allow us to explore various aspects of the physics of degenerate quantum gases in low dimensions. (author)

Absorption imaging of ultracold atoms on atom chips

DEFF Research Database (Denmark)

Smith, David A.; Aigner, Simon; Hofferberth, Sebastian

2011-01-01

Imaging ultracold atomic gases close to surfaces is an important tool for the detailed analysis of experiments carried out using atom chips. We describe the critical factors that need be considered, especially when the imaging beam is purposely reflected from the surface. In particular we present...... methods to measure the atom-surface distance, which is a prerequisite for magnetic field imaging and studies of atom surface-interactions....

Role of atom--atom inelastic collisions in two-temperature nonequilibrium plasmas

International Nuclear Information System (INIS)

Kunc, J.A.

1987-01-01

The contribution of inelastic atom--atom collisions to the production of electrons and excited atoms in two-temperature (with electron temperature T/sub e/, atomic temperature T/sub a/, and atomic density N/sub a/), steady-state, nonequilibrium atomic hydrogen plasma is investigated. The results are valid for plasmas having large amounts of atomic hydrogen as one of the plasma components, so that e--H and H--H inelastic collisions and interaction of these atoms with radiation dominate the production of electrons and excited hydrogen atoms. Densities of electrons and excited atoms are calculated in low-temperature plasma, with T/sub e/ and T/sub a/≤8000 K and 10 16 cm -3 ≤N/sub a/≤10 18 cm -3 , and with different degrees of the reabsorption of radiation. The results indicate that inelastic atom--atom collisions are important for production of electrons and excited atoms in partially ionized plasmas with medium and high atomic density and temperatures below 8000 K

Spatially resolved photoionization of ultracold atoms on an atom chip

International Nuclear Information System (INIS)

Kraft, S.; Guenther, A.; Fortagh, J.; Zimmermann, C.

2007-01-01

We report on photoionization of ultracold magnetically trapped Rb atoms on an atom chip. The atoms are trapped at 5 μK in a strongly anisotropic trap. Through a hole in the chip with a diameter of 150 μm, two laser beams are focused onto a fraction of the atomic cloud. A first laser beam with a wavelength of 778 nm excites the atoms via a two-photon transition to the 5D level. With a fiber laser at 1080 nm the excited atoms are photoionized. Ionization leads to depletion of the atomic density distribution observed by absorption imaging. The resonant ionization spectrum is reported. The setup used in this experiment is suitable not only to investigate mixtures of Bose-Einstein condensates and ions but also for single-atom detection on an atom chip

Clearance of buildings for demolition: ways to clearance on the standing structure for covered surfaces and inaccessible areas

International Nuclear Information System (INIS)

Thraenert, S.; Riemann, T.

2014-01-01

In general terms, the TUV NORD Nuclear services encompass safety assessments, design reviews, documentation re-views and inspections. They reflect the full scope of a technical service provider in the nuclear field. In the domestic market, these services are provided for the regulator, whereas in the international market any party involved in a nuclear project is a potential customer of TUV NORD Nuclear. This implies that TUV NORD Nuclear is offering consultancy, engineering and inspection services. Regarding the clearance of buildings for demolition, there are two different possible ways for the radiological characterization. The first option is a characterization on the standing structure before demolition and the second option is the characterization of the building rubble after demolition. According to the German Radiation Protection Ordinance, buildings of decommissioned nuclear sites have to be preferentially cleared on the standing structure. If compliance with the surface specific clearance levels is achieved on the standing structure, usually the cleared buildings can be demolished and the resulting rubble may be used without any further radiological considerations. In the case of the former nuclear power plant Wuergassen the majority of the building rubble is scheduled to stay on site to serve as backfill for the building pit. As such a scenario was not considered in the radiological considerations of, e.g., the German Radiation Protection Ordinance, an additional dose calculation was carried out for Wuergassen NPP basing on its radiological characteristics to directly prove compliance with the de-minimis-concept. The radiation controlled area (RCA) of Wuergassen NPP comprises an area of about 140.000 m 2 . This area is more or less easily accessible to characterization and decontamination using, if necessary, scaffoldings or lifting platforms. Up to the beginning of 2013, compliance with the surface specific clearance levels was verified on the standing

Linking environmental protection in practice. Advantages of a systematical method of sustainable building, from initiative to demolition; Aansluitende milieuzorg in de praktijk. Voordelen van een systematische aanpak van duurzaam bouwen, van initiatief tot sloop

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-07-01

Based on the results of four building projects the advantages of a systematical method (so-called linking environmental protection or in Dutch 'aansluitende milieuzorg') for sustainable construction of buildings are discussed. By formulating sound agreements and making sure that every party involved in the building process knows its tasks, responsibilities and competencies the whole process from initiative to demolition can be streamlined. By applying the right tools in every phase of the project the environmental effectiveness will be optimal.

Atomic polarizabilities

International Nuclear Information System (INIS)

Safronova, M. S.; Mitroy, J.; Clark, Charles W.; Kozlov, M. G.

2015-01-01

The atomic dipole polarizability governs the first-order response of an atom to an applied electric field. Atomic polarization phenomena impinge upon a number of areas and processes in physics and have been the subject of considerable interest and heightened importance in recent years. In this paper, we will summarize some of the recent applications of atomic polarizability studies. A summary of results for polarizabilities of noble gases, monovalent, and divalent atoms is given. The development of the CI+all-order method that combines configuration interaction and linearized coupled-cluster approaches is discussed

Atomic polarizabilities

Energy Technology Data Exchange (ETDEWEB)

Safronova, M. S. [Department of Physics and Astronomy, University of Delaware, Newark, DE 19716 (United States); Mitroy, J. [School of Engineering, Charles Darwin University, Darwin NT 0909 (Australia); Clark, Charles W. [Joint Quantum Institute, National Institute of Standards and Technology and the University of Maryland, Gaithersburg, Maryland 20899-8410 (United States); Kozlov, M. G. [Petersburg Nuclear Physics Institute, Gatchina 188300 (Russian Federation)

2015-01-22

The atomic dipole polarizability governs the first-order response of an atom to an applied electric field. Atomic polarization phenomena impinge upon a number of areas and processes in physics and have been the subject of considerable interest and heightened importance in recent years. In this paper, we will summarize some of the recent applications of atomic polarizability studies. A summary of results for polarizabilities of noble gases, monovalent, and divalent atoms is given. The development of the CI+all-order method that combines configuration interaction and linearized coupled-cluster approaches is discussed.

Atomic physics

CERN Document Server

Foot, Christopher J

2007-01-01

This text will thoroughly update the existing literature on atomic physics. Intended to accompany an advanced undergraduate course in atomic physics, the book will lead the students up to the latest advances and the applications to Bose-Einstein Condensation of atoms, matter-wave inter-ferometry and quantum computing with trapped ions. The elementary atomic physics covered in the early chapters should be accessible to undergraduates when they are first introduced to the subject. To complement. the usual quantum mechanical treatment of atomic structure the book strongly emphasizes the experimen

Systematics of atom-atom collision strengths at high speeds

International Nuclear Information System (INIS)

Gillespie, G.H.; Inokuti, M.

1980-01-01

The collision strengths for atom-atom collisions at high speeds are calculated in the first Born approximation. We studied four classes of collisions, distinguished depending upon whether each of the collision partners becomes excited or not. The results of numerical calculations of the collision strengths are presented for all neutral atoms with Z< or =18. The calculations are based on atomic form factors and incoherent scattering functions found in the literature. The relative contribution of each class of collision processes to the total collision cross section is examined in detail. In general, inelastic processes dominate for low-Z atoms, while elastic scattering is more important for large Z. Other systematics of the collision strengths are comprehensively discussed. The relevant experimental literature has been surveyed and the results of this work for the three collision systems H-He, He-He, and H-Ar are compared with the data for electron-loss processes. Finally, suggestions are made for future work in measurements of atom-atom and ion-atom collision cross sections

Atomic Absorption, Atomic Fluorescence, and Flame Emission Spectrometry.

Science.gov (United States)

Horlick, Gary

1984-01-01

This review is presented in six sections. Sections focus on literature related to: (1) developments in instrumentation, measurement techniques, and procedures; (2) performance studies of flames and electrothermal atomizers; (3) applications of atomic absorption spectrometry; (4) analytical comparisons; (5) atomic fluorescence spectrometry; and (6)…

Stable atomic hydrogen: Polarized atomic beam source

International Nuclear Information System (INIS)

Niinikoski, T.O.; Penttilae, S.; Rieubland, J.M.; Rijllart, A.

1984-01-01

We have carried out experiments with stable atomic hydrogen with a view to possible applications in polarized targets or polarized atomic beam sources. Recent results from the stabilization apparatus are described. The first stable atomic hydrogen beam source based on the microwave extraction method (which is being tested ) is presented. The effect of the stabilized hydrogen gas density on the properties of the source is discussed. (orig.)

Highly excited atoms

International Nuclear Information System (INIS)

Kleppner, D.; Littman, M.G.; Zimmerman, M.L.

1981-01-01

Highly excited atoms are often called Rydberg atoms. These atoms have a wealth of exotic properties which are discussed. Of special interest, are the effects of electric and magnetic fields on Rydberg atoms. Ordinary atoms are scarcely affected by an applied electric or magnetic field; Rydberg atoms can be strongly distorted and even pulled apart by a relatively weak electric field, and they can be squeezed into unexpected shapes by a magnetic field. Studies of the structure of Rydberg atoms in electric and magnetic fields have revealed dramatic atomic phenomena that had not been observed before

Atomic mirrors for a Λ-type three-level atom

International Nuclear Information System (INIS)

Felemban, Nuha; Aldossary, Omar M; Lembessis, Vassilis E

2014-01-01

We propose atom mirror schemes for a three-level atom of Λ-type interacting with two evanescent fields, which are generated as a result of the total internal reflection of two coherent Gaussian laser beams at the interface of a dielectric prism with vacuum. The forces acting on the atom are derived by means of optical Bloch equations, based on the atomic density matrix elements. The theory is illustrated by setting up the equations of motion for 23 Na atom. Two types of excited schemes are examined, namely the cases in which the evanescent fields have polarization types of σ + −σ − and σ + −π. The equations are solved numerically and we get results for atomic trajectories for different parameters. The performance of the mirror for the two types of polarization schemes is quantified and discussed. The possibility of reflecting atoms at pre-determined directions is also discussed. (paper)

Quasi-atoms

International Nuclear Information System (INIS)

Armbruster, P.

1976-01-01

The concept of a quasi-atom is discussed, and several experiments are described in which molecular or quasi-atomic transitions have been observed. X-ray spectra are shown for these experiments in which heavy ion projectiles were incident on various targets and the resultant combined system behaved as a quasi-atom. This rapidly developing field has already given new insight into atomic collision phenomena. (P.J.S.)

Atomic fusion, Gerrard atomic fusion

International Nuclear Information System (INIS)

Gerrard, T.H.

1980-01-01

In the approach to atomic fusion described here the heat produced in a fusion reaction, which is induced in a chamber by the interaction of laser beams and U.H.F. electromagnetic beams with atom streams, is transferred to a heat exchanger for electricity generation by a coolant flowing through a jacket surrounding the chamber. (U.K.)

Decommissioning of the Shippingport Atomic Power Station

International Nuclear Information System (INIS)

LaGuardia, T.S.

1988-01-01

The Shippingport reactor was originally designed as a pressurized water reactor and operated for approximately 10 years in that mode. Later, in 1967 it was converted to a light water breeder reactor and continued its operation until 1985, when the reactor was shut down. However, the decommissioning planning for Shippingport was begun in 1979. Detailed engineering and planning was undertaken to look at alternatives for disposal of the reactor vessel, the overall detailed estimated costs, the exposure to the workers and the waste volume generated and to prepare activity specifications for performance of the work. The program scope and component removal are detailed. The scarification of contaminated concrete, building demolition, special tools and equipment needed and work performance data are described. The successful removal of the primary system components and piping has been completed. (author)

Interferometry with atoms

International Nuclear Information System (INIS)

Helmcke, J.; Riehle, F.; Witte, A.; Kisters, T.

1992-01-01

Physics and experimental results of atom interferometry are reviewed and several realizations of atom interferometers are summarized. As a typical example of an atom interferometer utilizing the internal degrees of freedom of the atom, we discuss the separated field excitation of a calcium atomic beam using four traveling laser fields and demonstrate the Sagnac effect in a rotating interferometer. The sensitivity of this interferometer can be largely increased by use of slow atoms with narrow velocity distribution. We therefore furthermore report on the preparation of a laser cooled and deflected calcium atomic beam. (orig.)

Conduction of molecular electronic devices: Qualitative insights through atom-atom polarizabilities

International Nuclear Information System (INIS)

Stuyver, T.; Fias, S.; De Proft, F.; Geerlings, P.; Fowler, P. W.

2015-01-01

The atom-atom polarizability and the transmission probability at the Fermi level, as obtained through the source-and-sink-potential method for every possible configuration of contacts simultaneously, are compared for polycyclic aromatic compounds. This comparison leads to the conjecture that a positive atom-atom polarizability is a necessary condition for transmission to take place in alternant hydrocarbons without non-bonding orbitals and that the relative transmission probability for different configurations of the contacts can be predicted by analyzing the corresponding atom-atom polarizability. A theoretical link between the two considered properties is derived, leading to a mathematical explanation for the observed trends for transmission based on the atom-atom polarizability

Conduction of molecular electronic devices: Qualitative insights through atom-atom polarizabilities

Energy Technology Data Exchange (ETDEWEB)

Stuyver, T.; Fias, S., E-mail: sfias@vub.ac.be; De Proft, F.; Geerlings, P. [ALGC, Vrije Universiteit Brussel, Pleinlaan 2, 1050 Brussel (Belgium); Fowler, P. W. [Department of Chemistry, University of Sheffield, Sheffield S3 7HF (United Kingdom)

2015-03-07

The atom-atom polarizability and the transmission probability at the Fermi level, as obtained through the source-and-sink-potential method for every possible configuration of contacts simultaneously, are compared for polycyclic aromatic compounds. This comparison leads to the conjecture that a positive atom-atom polarizability is a necessary condition for transmission to take place in alternant hydrocarbons without non-bonding orbitals and that the relative transmission probability for different configurations of the contacts can be predicted by analyzing the corresponding atom-atom polarizability. A theoretical link between the two considered properties is derived, leading to a mathematical explanation for the observed trends for transmission based on the atom-atom polarizability.

Conduction of molecular electronic devices: qualitative insights through atom-atom polarizabilities.

Science.gov (United States)

Stuyver, T; Fias, S; De Proft, F; Fowler, P W; Geerlings, P

2015-03-07

The atom-atom polarizability and the transmission probability at the Fermi level, as obtained through the source-and-sink-potential method for every possible configuration of contacts simultaneously, are compared for polycyclic aromatic compounds. This comparison leads to the conjecture that a positive atom-atom polarizability is a necessary condition for transmission to take place in alternant hydrocarbons without non-bonding orbitals and that the relative transmission probability for different configurations of the contacts can be predicted by analyzing the corresponding atom-atom polarizability. A theoretical link between the two considered properties is derived, leading to a mathematical explanation for the observed trends for transmission based on the atom-atom polarizability.

Landfill disposal of CCA-treated wood with construction and demolition (C&D) debris: arsenic, chromium, and copper concentrations in leachate.

Science.gov (United States)

Jambeck, Jenna R; Townsend, Timothy G; Solo-Gabriele, Helena M

2008-08-01

Although phased out of many residential uses in the United States, the disposal of CCA-treated wood remains a concern because significant quantities have yet to be taken out of service, and it is commonly disposed in landfills. Catastrophic events have also led to the concentrated disposal of CCA-treated wood, often in unlined landfills. The goal of this research was to simulate the complex chemical and biological activity of a construction and demolition (C&D) debris landfill containing a realistic quantity of CCA-treated wood (10% by mass), produce leachate, and then evaluate the arsenic, copper, and chromium concentrations in the leachate as an indication of what may occur in a landfill setting. Copper concentrations were not significantly elevated in the control or experimental simulated landfill setting (alpha = 0.05). However, the concentrations of arsenic and chromium were significantly higher in the experimental simulated landfill leachate compared to the control simulated landfill leachate (alpha = 0.05, p debris can impact leachate quality which, in turn could affect leachate management practices or aquifers below unlined landfills.

Generation of macroscopic singlet states in atomic ensembles

Science.gov (United States)

Tóth, Géza; Mitchell, Morgan W.

2010-05-01

We study squeezing of the spin uncertainties by quantum non-demolition (QND) measurement in non-polarized spin ensembles. Unlike the case of polarized ensembles, the QND measurements can be performed with negligible back-action, which allows, in principle, perfect spin squeezing as quantified by Tóth et al (2007 Phys. Rev. Lett. 99 250405). The generated spin states approach many-body singlet states and contain a macroscopic number of entangled particles even when individual spin is large. We introduce the Gaussian treatment of unpolarized spin states and use it to estimate the achievable spin squeezing for realistic experimental parameters. Our proposal might have applications for magnetometry with a high spatial resolution or quantum memories storing information in decoherence free subspaces.

Magnetic atom optics: mirrors, guides, traps, and chips for atoms

Energy Technology Data Exchange (ETDEWEB)

Hinds, E.A.; Hughes, I.G. [Sussex Centre for Optical and Atomic Physics, University of Sussex, Brighton (United Kingdom)

1999-09-21

For the last decade it has been possible to cool atoms to microkelvin temperatures ({approx}1 cm s{sup -1}) using a variety of optical techniques. Light beams provide the very strong frictional forces required to slow atoms from room temperature ({approx}500 m s{sup -1}). However, once the atoms are cold, the relatively weak conservative forces of static electric and magnetic fields play an important role. In our group we have been studying the interaction of cold rubidium atoms with periodically magnetized data storage media. Here we review the underlying principles of the forces acting on atoms above a suitably magnetized substrate or near current-carrying wires. We also summarize the status of experiments. These structures can be used as smooth or corrugated reflectors for controlling the trajectories of cold atoms. Alternatively, they may be used to confine atoms to a plane, a line, or a dot and in some cases to reach the quantum limit of confinement. Atoms levitated above a magnetized surface can be guided electrostatically by wires deposited on the surface. The flow and interaction of atoms in such a structure may form the basis of a new technology, 'integrated atom optics' which might ultimately be capable of realizing a quantum computer. (author)

Air Dispersion Modeling for Building 3026C/D Demolition

Energy Technology Data Exchange (ETDEWEB)

Ward, Richard C [ORNL; Sjoreen, Andrea L [ORNL; Eckerman, Keith F [ORNL

2010-06-01

This report presents estimates of dispersion coefficients and effective dose for potential air dispersion scenarios of uncontrolled releases from Oak Ridge National Laboratory (ORNL) buildings 3026C, 3026D, and 3140 prior to or during the demolition of the 3026 Complex. The Environmental Protection Agency (EPA) AERMOD system1-6 was used to compute these estimates. AERMOD stands for AERMIC Model, where AERMIC is the American Meteorological Society-EPA Regulatory Model Improvement Committee. Five source locations (three in building 3026D and one each in building 3026C and the filter house 3140) and associated source characteristics were determined with the customer. In addition, the area of study was determined and building footprints and intake locations of air-handling systems were obtained. In addition to the air intakes, receptor sites consisting of ground level locations on four polar grids (50 m, 100 m, 200 m, and 500 m) and two intersecting lines of points (50 m separation), corresponding to sidewalks along Central Avenue and Fifth Street. Three years of meteorological data (2006 2008) were used each consisting of three datasets: 1) National Weather Service data; 2) upper air data for the Knoxville-Oak Ridge area; and 3) local weather data from Tower C (10 m, 30 m and 100 m) on the ORNL reservation. Annual average air concentration, highest 1 h average and highest 3 h average air concentrations were computed using AERMOD for the five source locations for the three years of meteorological data. The highest 1 h average air concentrations were converted to dispersion coefficients to characterize the atmospheric dispersion as the customer was interested in the most significant response and the highest 1 h average data reflects the best time-averaged values available from the AERMOD code. Results are presented in tabular and graphical form. The results for dose were obtained using radionuclide activities for each of the buildings provided by the customer.7

Low energy atom-atom collisions

International Nuclear Information System (INIS)

Child, M.S.

1980-01-01

The semiclassical theory of atom-atom potential scattering and of low energy inelastic atom-atom scattering is reviewed. Particular attention is given to the origin and interpretation of rainbow structure, diffraction oscillations and exchange oscillations in the potential scattering differential cross-section, and to the glory structure and symmetry oscillations in the integral cross-section. Available methods for direct inversion of the cross-section data to recover the potential are reviewed in some detail. The theory of non-adiabatic transitions is introduced by a short discussion of interaction mechanisms and of diabetic and adiabatic representations. Analytical S matrix elements are presented for two state curve-crossing (Landau-Zener-Stuckelberg), Demkov and Nikitin models. The relation between Stuckelberg oscillations in the S matrix and in the differential cross-section is discussed in terms of interference between trajectories belonging to two different classical deflection functions. The energy dependences of the inelastic integral cross-section for curve-crossing and Demkov type transitions are also discussed. Finally the theory is reviewed in relation to a recent close-coupled study of fine structure transitions in F( 2 P) + Xe( 2 S) scattering

Mechanism of yttrium atom formation in electrothermal atomization from metallic and metal-carbide surfaces of a heated graphite atomizer in atomic absorption spectrometry

International Nuclear Information System (INIS)

Wahab, H.S.; Chakrabarti, C.L.

1981-01-01

Mechanism of Y atom formation from pyrocoated graphite, tantalum and tungsten metal surfaces of a graphite tube atomizer has been studied and a mechanism for the formation for Y atoms is proposed for the first time. (author)

Atomic Physics 16: Sixteenth International Conference on Atomic Physics. Proceedings

International Nuclear Information System (INIS)

Baylis, W.E.; Drake, G.W.

1999-01-01

These proceedings represent papers presented at the 16th International Conference on Atomic Physics held in Windsor, Ontario, Canada, in August, 1998. The topics discussed included a wide array of subjects in atomic physics such as atom holography, alignment in atomic collisions, coulomb-interacting particles, muon experiments, x-rays from comets, atomic electron collisions in intense laser fields, spectroscopy of trapped ions, and Bose-Einstein condensates. This conference represents the single most important meeting world wide on fundamental advances in atomic physics. There were 30 papers presented at the conference,out of which 4 have been abstracted for the Energy, Science and Technology database

Occurrence of organic pollutants in recovered soil fines from construction and demolition waste.

Science.gov (United States)

Jang, Y C; Townsend, T G

2001-01-01

The objective of this study was to characterize recovered soil fines from construction and demolition (C&D) waste recycling facilities for trace organic pollutants. Over a period of 18 months, five sampling trips were made to 14 C&D waste recycling facilities in Florida. Screened soil fines were collected from older stockpiles and newly generated piles at the sites. The samples were analyzed for the total concentration (mg/kg) of a series of volatile organic compound (VOCs) and semi-volatile organic compounds (semi-VOCs). The synthetic precipitation leaching procedure (SPLP) test was also performed to evaluate the leachability of the trace organic chemicals. During the total analysis only a few volatile organic compounds were commonly found in the samples (trichlorofluoromethane, toluene, 4-isopropyltoluene, trimethylbenzene, xylenes, and methylene chloride). A total of nine VOCs were detected in the leaching test. Toluene showed the highest leachability among the compounds (61.3-92.0%), while trichlorofluoromethane, the most commonly detected compound from both the total and leaching tests, resulted in the lowest leachability (1.4-39.9%). For the semi-VOC analysis, three base-neutral semi-VOC compounds (bis(2-ethylhexyl)phthalate, butyl benzyl phthalate, and di-n-butyl phthalate) and several PAHs (acenaphthene, pyrene, fluoranthene, and phenanthrene) were commonly detected in C&D fines samples. These compounds also leached during the SPLP leaching test (0.1-25%). No acid extractable compounds, pesticides, or PCBs were detected. The results of this study were further investigated to assess risk from land applied recovered soil fines by comparing total and leaching concentrations of recovered soil fines samples to risk-based standards. The results of this indicate that the organic chemicals in recovered soil fines from C&D debris recycling facilities were not of a major concern in terms of human risk and leaching risk to groundwater under reuse and contact scenarios.

Penetration Evaluation of Explosively Formed Projectiles Through Air and Water Using Insensitive Munition: Simulative and Experimental Studies

Directory of Open Access Journals (Sweden)

M. Ahmed

2016-02-01

Full Text Available The process of formation, flying, penetration of explosively-formed projectiles (EFP and the effect of water on performance of the charge for underwater applications is simulated by Ansysis Autodyn 2D-Hydro code. The main objective of an explosively formed projectile designed for underwater applications is to disintegrate the target at longer standoff distances. In this paper we have simulated the explosively formed projectile from OFHC-Copper liner for 1200 conical angle. The Affect of water on the penetration of EFP is determined by simulations from Ansysis Autodyn 2-D Hydrocode and by varying depth of water from 1CD-5CD. The depth of penetration against steel target is measured experimentally. Flash X-Ray Radiography (FXR is used to capture EFP jet formation and its penetration against target is measured by depth of penetration experiments. Simulation results are compared with experimental results. The difference in simulated and experimental results for depth of penetration is about 7 mm, which lies within favorable range of error. The jet formation captured from FXR is quite clear and jet velocity determined from Flash X-ray radiography is the same as the ones obtained by using other high explosives. Therefore, it is indicated that Insensitive Munition (8701 can be utilized instead of Polymer Bonded Explosives (PBX for air and underwater environments with great reliability and without any hazard.

A low-cost vaporization-atomization system for atomic absorption spectrometry

International Nuclear Information System (INIS)

Bruhn F, C.G.; Ambiado V, F.; Woerner V, R.

1990-01-01

A low-cost vaporization-atomization system for atomic absorption spectrometry is developed as an alternative to the use of a graphite furnace in electrothermal atomic absorption spectrometry. (Author)

Atom localization via controlled spontaneous emission in a five-level atomic system

International Nuclear Information System (INIS)

Wang Zhiping; Yu Benli; Zhu Jun; Cao Zhigang; Zhen Shenglai; Wu Xuqiang; Xu Feng

2012-01-01

We investigate the one- and two-dimensional atom localization behaviors via spontaneous emission in a coherently driven five-level atomic system by means of a radio-frequency field driving a hyperfine transition. It is found that the detecting probability and precision of atom localization behaviors can be significantly improved via adjusting the system parameters. More importantly, the two-dimensional atom localization patterns reveal that the maximal probability of finding an atom within the sub-wavelength domain of the standing waves can reach unity when the corresponding conditions are satisfied. As a result, our scheme may be helpful in laser cooling or the atom nano-lithography via atom localization. - Highlights: ► One- and two-dimensional atom localization behaviors via spontaneous emission in five-level atoms are investigated. ► An assisting radio-frequency field is used to control the atom localization behaviors. ► High-precision and high-resolution two-dimensional atom localization can be realized in this scheme.

Three-atom clusters

International Nuclear Information System (INIS)

Pen'kov, F.M.

1998-01-01

The Born-Oppenheimer approximation is used to obtain an equation for the effective interaction in three atoms bound by a single electron. For low binding energies in an 'electron + atom' pair, long-range forces arise between the atoms, leading to bound states when the size of the three-atom cluster is a few tens of angstrom. A system made of alkali-metal atoms is considered as an example

Atomic Fisher information versus atomic number

International Nuclear Information System (INIS)

Nagy, A.; Sen, K.D.

2006-01-01

It is shown that the Thomas-Fermi Fisher information is negative. A slightly more sophisticated model proposed by Gaspar provides a qualitatively correct expression for the Fisher information: Gaspar's Fisher information is proportional to the two-third power of the atomic number. Accurate numerical calculations show an almost linear dependence on the atomic number

Atomic-fluorescence spectrophotometry

International Nuclear Information System (INIS)

Bakhturova, N.F.; Yudelevich, I.G.

1975-01-01

Atomic-fluorescence spectrophotometry, a comparatively new method for the analysis of trace quantities, has developed rapidly in the past ten years. Theoretical and experimental studies by many workers have shown that atomic-fluorescence spectrophotometry (AFS) is capable of achieving a better limit than atomic absorption for a large number of elements. The present review examines briefly the principles of atomic-fluorescence spectrophotometry and the types of fluorescent transition. The excitation sources, flame and nonflame atomizers, used in AFS are described. The limits of detection achieved up to the present, using flame and nonflame methods of atomization are given

Optically polarized atoms understanding light-atom interactions

CERN Document Server

Auzinsh, Marcis; Rochester, Simon M

2010-01-01

This book is addressed at upper-level undergraduate and graduate students involved in research in atomic, molecular, and optical Physics. It will also be useful to researchers practising in this field. It gives an intuitive, yet sufficiently detailed and rigorous introduction to light-atom interactions with a particular emphasis on the symmetry aspects of the interaction, especially those associated with the angular momentum of atoms and light. The book will enable readers to carryout practical calculations on their own, and is richly illustrated with examples drawn from current research topic

Decay of long-lived autoionization atomic states in atom collisions

International Nuclear Information System (INIS)

Krakov, B.G.

1994-01-01

Radiationless decay of long-lived autoionization states of helium atoms in atom collisions is investigated. It is shown that the states may decay in atom collisions due to softening of the selection rules

Hot atom chemistry of monovalent atoms in organic condensed phases

International Nuclear Information System (INIS)

Stoecklin, G.

1975-01-01

The advantages and disadvantages of hot atom studies in condensed organic phases are considered, and recent advances in condensed phase organic hot atom chemistry of recoil tritium and halogen atoms are discussed. Details are presented of the present status and understanding of liquid phase hot atom chemistry and also that of organic solids. The consequences of the Auger effect in condensed organic systems are also considered. (author)

Ab initio calculation atomics ground state wave function for interactions Ion- Atom

International Nuclear Information System (INIS)

Shojaee, F.; Bolori zadeh, M. A.

2007-01-01

Ab initio calculation atomics ground state wave function for interactions Ion- Atom Atomic wave function expressed in a Slater - type basis obtained within Roothaan- Hartree - Fock for the ground state of the atoms He through B. The total energy is given for each atom.

Atomic switches: atomic-movement-controlled nanodevices for new types of computing

International Nuclear Information System (INIS)

Hino, Takami; Hasegawa, Tsuyoshi; Terabe, Kazuya; Tsuruoka, Tohru; Nayak, Alpana; Ohno, Takeo; Aono, Masakazu

2011-01-01

Atomic switches are nanoionic devices that control the diffusion of metal cations and their reduction/oxidation processes in the switching operation to form/annihilate a metal atomic bridge, which is a conductive path between two electrodes in the on-state. In contrast to conventional semiconductor devices, atomic switches can provide a highly conductive channel even if their size is of nanometer order. In addition to their small size and low on-resistance, their nonvolatility has enabled the development of new types of programmable devices, which may achieve all the required functions on a single chip. Three-terminal atomic switches have also been developed, in which the formation and annihilation of a metal atomic bridge between a source electrode and a drain electrode are controlled by a third (gate) electrode. Three-terminal atomic switches are expected to enhance the development of new types of logic circuits, such as nonvolatile logic. The recent development of atomic switches that use a metal oxide as the ionic conductive material has enabled the integration of atomic switches with complementary metal-oxide-semiconductor (CMOS) devices, which will facilitate the commercialization of atomic switches. The novel characteristics of atomic switches, such as their learning and photosensing abilities, are also introduced in the latter part of this review. (topical review)

Atomic physics

International Nuclear Information System (INIS)

Anon.

1976-01-01

Research activities in atomic physics at Lawrence Berkeley Laboratory during 1976 are described. Topics covered include: experiments on stored ions; test for parity violation in neutral weak currents; energy conservation and astrophysics; atomic absorption spectroscopy, atomic and molecular detectors; theoretical studies of quantum electrodynamics and high-z ions; atomic beam magnetic resonance; radiative decay from the 2 3 Po, 2 levels of helium-like argon; quenching of the metastable 2S/sub 1/2/ state of hydrogen-like argon in an external electric field; and lifetime of the 2 3 Po level of helium-like krypton

Soil retention of hexavalent chromium released from construction and demolition waste in a road-base-application scenario.

Science.gov (United States)

Butera, Stefania; Trapp, Stefan; Astrup, Thomas F; Christensen, Thomas H

2015-11-15

We investigated the retention of Cr(VI) in three subsoils with low organic matter content in laboratory experiments at concentration levels relevant to represent leachates from construction and demolition waste (C&DW) reused as unbound material in road construction. The retention mechanism appeared to be reduction and subsequent precipitation as Cr(III) on the soil. The reduction process was slow and in several experiments it was still proceeding at the end of the six-month experimental period. The overall retention reaction fit well with a second-order reaction governed by actual Cr(VI) concentration and reduction capacity of the soil. The experimentally determined reduction capacities and second-order kinetic parameters were used to model, for a 100-year period, the one-dimensional migration of Cr(VI) in the subsoil under a layer of C&DW. The resulting Cr(VI) concentration would be negligible below 7-70 cm depth. However, in rigid climates and with high water infiltration through the road pavement, the reduction reaction could be so slow that Cr(VI) might migrate as deep as 200 cm under the road. The reaction parameters and the model can form the basis for systematically assessing under which scenarios Cr(VI) from C&DW could lead to an environmental issue for ground- and receiving surface waters. Copyright © 2015 Elsevier B.V. All rights reserved.

Progress in atomic spectroscopy

International Nuclear Information System (INIS)

Beyer, H.J.; Kleinpoppen, H.

1984-01-01

This book presents reviews by leading experts in the field covering areas of research at the forefront of atomic spectroscopy. Topics considered include the k ordering of atomic structure, multiconfiguration Hartree-Fock calculations for complex atoms, new methods in high-resolution laser spectroscopy, resonance ionization spectroscopy (inert atom detection), trapped ion spectroscopy, high-magnetic-field atomic physics, the effects of magnetic and electric fields on highly excited atoms, x rays from superheavy collision systems, recoil ion spectroscopy with heavy ions, investigations of superheavy quasi-atoms via spectroscopy of electron rays and positrons, impact ionization by fast projectiles, and amplitudes and state parameters from ion- and atom-atom excitation processes

Atomic reactor thermal engineering

International Nuclear Information System (INIS)

Kim, Gwang Ryong

1983-02-01

This book starts the introduction of atomic reactor thermal engineering including atomic reaction, chemical reaction, nuclear reaction neutron energy and soon. It explains heat transfer, heat production in the atomic reactor, heat transfer of fuel element in atomic reactor, heat transfer and flow of cooler, thermal design of atomic reactor, design of thermodynamics of atomic reactor and various. This deals with the basic knowledge of thermal engineering for atomic reactor.

Rapid prototyping of versatile atom chips for atom interferometry applications.

Science.gov (United States)

Kasch, Brian; Squires, Matthew; Olson, Spencer; Kroese, Bethany; Imhof, Eric; Kohn, Rudolph; Stuhl, Benjamin; Schramm, Stacy; Stickney, James

2016-05-01

We present recent advances in the manipulation of ultracold atoms with ex-vacuo atom chips (i.e. atom chips that are not inside to the UHV chamber). Details will be presented of an experimental system that allows direct bonded copper (DBC) atom chips to be removed and replaced in minutes, requiring minimal re-optimization of parameters. This system has been used to create Bose-Einstein condensates, as well as magnetic waveguides with precisely tunable axial parameters, allowing double wells, pure harmonic confinement, and modified harmonic traps. We investigate the effects of higher order magnetic field contributions to the waveguide, and the implications for confined atom interferometry.

First-Order Quantum Phase Transition for Dicke Model Induced by Atom-Atom Interaction

International Nuclear Information System (INIS)

Zhao Xiu-Qin; Liu Ni; Liang Jiu-Qing

2017-01-01

In this article, we use the spin coherent state transformation and the ground state variational method to theoretically calculate the ground function. In order to consider the influence of the atom-atom interaction on the extended Dicke model’s ground state properties, the mean photon number, the scaled atomic population and the average ground energy are displayed. Using the self-consistent field theory to solve the atom-atom interaction, we discover the system undergoes a first-order quantum phase transition from the normal phase to the superradiant phase, but a famous Dicke-type second-order quantum phase transition without the atom-atom interaction. Meanwhile, the atom-atom interaction makes the phase transition point shift to the lower atom-photon collective coupling strength. (paper)

Evolution Properties of Atomic Fidelity in the Combined Multi-Atom-Cavity Field System

International Nuclear Information System (INIS)

Wang Ju-Xia; Zhang Xiao-Juan; Zhang Xiu-Xing

2015-01-01

The atom fidelity is investigated in a system consisting of Mtwo-level atoms and M single-mode fields by use of complete quantum theory and numerical evaluation method. The influences of various system parameters on the evolution of atomic fidelity are studied. The results show that the atomic fidelity evolves in a Rabi oscillation manner. The oscillation frequency is mainly modulated by the coupling strength between atoms and light field, the atomic transition probabilities and the average photon numbers. Other factors hardly impact on the atomic fidelity. The present results may provide a useful approach to the maintenance of the atomic fidelity in the atom cavity field systems. (paper)

AtomPy: an open atomic-data curation environment

Science.gov (United States)

Bautista, Manuel; Mendoza, Claudio; Boswell, Josiah S; Ajoku, Chukwuemeka

2014-06-01

We present a cloud-computing environment for atomic data curation, networking among atomic data providers and users, teaching-and-learning, and interfacing with spectral modeling software. The system is based on Google-Drive Sheets, Pandas (Python Data Analysis Library) DataFrames, and IPython Notebooks for open community-driven curation of atomic data for scientific and technological applications. The atomic model for each ionic species is contained in a multi-sheet Google-Drive workbook, where the atomic parameters from all known public sources are progressively stored. Metadata (provenance, community discussion, etc.) accompanying every entry in the database are stored through Notebooks. Education tools on the physics of atomic processes as well as their relevance to plasma and spectral modeling are based on IPython Notebooks that integrate written material, images, videos, and active computer-tool workflows. Data processing workflows and collaborative software developments are encouraged and managed through the GitHub social network. Relevant issues this platform intends to address are: (i) data quality by allowing open access to both data producers and users in order to attain completeness, accuracy, consistency, provenance and currentness; (ii) comparisons of different datasets to facilitate accuracy assessment; (iii) downloading to local data structures (i.e. Pandas DataFrames) for further manipulation and analysis by prospective users; and (iv) data preservation by avoiding the discard of outdated sets.

Ubiquitous atom

International Nuclear Information System (INIS)

Spruch, G.M.; Spruch, L.

1974-01-01

The fundamentals of modern physics, including the basic physics and chemistry of the atom, elementary particles, cosmology, periodicity, and recent advances, are surveyed. The biology and chemistry of the life process is discussed to provide a background for considering the effects of atomic particles on living things. The uses of atomic power in space travel, merchant shipping, food preservation, desalination, and nuclear clocks are explored. (Pollut. Abstr.)

Modeling midwave infrared muzzle flash spectra from unsuppressed and flash-suppressed large caliber munitions

Science.gov (United States)

Steward, Bryan J.; Perram, Glen P.; Gross, Kevin C.

2012-07-01

Time-resolved infrared spectra of firings from a 152 mm howitzer were acquired over an 1800-6000 cm-1 spectral range using a Fourier-transform spectrometer. The instrument collected primarily at 32 cm-1 spectral and 100 Hz temporal resolutions. Munitions included unsuppressed and chemically flash suppressed propellants. Secondary combustion occurred with unsuppressed propellants resulting in flash emissions lasting ˜100 ms and dominated by H2O and CO2 spectral structure. Non-combusting plume emissions were one-tenth as intense and approached background levels within 20-40 ms. A low-dimensional phenomenological model was used to reduce the data to temperatures, soot absorbances, and column densities of H2O, CO2, CH4, and CO. The combusting plumes exhibit peak temperatures of ˜1400 K, areas of greater than 32 m2, low soot emissivity of ˜0.04, with nearly all the CO converted to CO2. The non-combusting plumes exhibit lower temperatures of ˜1000 K, areas of ˜5 m2, soot emissivity of greater than 0.38 and CO as the primary product. Maximum fit residual relative to peak intensity are 14% and 8.9% for combusting and non-combusting plumes, respectively. The model was generalized to account for turbulence-induced variations in the muzzle plumes. Distributions of temperature and concentration in 1-2 spatial regions demonstrate a reduction in maximum residuals by 40%. A two-region model of combusting plumes provides a plausible interpretation as a ˜1550 K, optically thick plume core and ˜2550 K, thin, surface-layer flame-front. Temperature rate of change was used to characterize timescales and energy release for plume emissions. Heat of combustion was estimated to be ˜5 MJ/kg.

Gold volatile species atomization and preconcentration in quartz devices for atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Arslan, Yasin [Institute of Analytical Chemistry of the ASCR, v. v. i., Veveří 97, 602 00 Brno (Czech Republic); Mehmet Akif Ersoy University, Faculty of Arts & Sciences, Chemistry Department, 15030 Burdur (Turkey); Musil, Stanislav; Matoušek, Tomáš; Kratzer, Jan [Institute of Analytical Chemistry of the ASCR, v. v. i., Veveří 97, 602 00 Brno (Czech Republic); Dědina, Jiří, E-mail: dedina@biomed.cas.cz [Institute of Analytical Chemistry of the ASCR, v. v. i., Veveří 97, 602 00 Brno (Czech Republic)

2015-01-01

The on-line atomization of gold volatile species was studied and the results were compared with thermodynamic calculations in several quartz atomizers, namely: diffusion flame, flame-in-gas-shield, flame-in-plain-tube, externally heated T-tube and externally heated flame-in-T-tube. Atomization mechanism in the explored devices is proposed, where volatile species are converted to thermodynamically stable AuH at elevated temperature over 500 °C and then atomized by an interaction with a cloud of hydrogen radicals. Because of its inherent simplicity and robustness, diffusion flame was employed as a reference atomizer. It yielded atomization efficiency of 70 to 100% and a very good long time reproducibility of peak area sensitivity: 1.6 to 1.8 s μg{sup −1}. Six and eleven times higher sensitivity, respectively, was provided by atomizers with longer light paths in the observation volume, i.e. externally heated T-tube and externally heated flame-in-T-tube. The latter one, offering limit of detection below 0.01 μg ml{sup −1}, appeared as the most prospective for on-line atomization. Insight into the mechanism of atomization of gold volatile species, into the fate of free atoms and into subsequent analyte transfer allowed to assess possibilities of in-atomizer preconcentration of gold volatile species: it is unfeasible with quartz atomizers but a sapphire tube atomizer could be useful in this respect. - Highlights: • On-line atomization of gold volatile species for AAS in quartz devices was studied. • Atomization mechanism was proposed and atomization efficiency was estimated. • Possibilities of in-atomizer preconcentration of gold volatile species were assessed.

Electronic structure of atoms: atomic spectroscopy information system

International Nuclear Information System (INIS)

Kazakov, V V; Kazakov, V G; Kovalev, V S; Meshkov, O I; Yatsenko, A S

2017-01-01

The article presents a Russian atomic spectroscopy, information system electronic structure of atoms (IS ESA) (http://grotrian.nsu.ru), and describes its main features and options to support research and training. The database contains over 234 000 records, great attention paid to experimental data and uniform filling of the database for all atomic numbers Z, including classified levels and transitions of rare earth and transuranic elements and their ions. Original means of visualization of scientific data in the form of spectrograms and Grotrian diagrams have been proposed. Presentation of spectral data in the form of interactive color charts facilitates understanding and analysis of properties of atomic systems. The use of the spectral data of the IS ESA together with its functionality is effective for solving various scientific problems and training of specialists. (paper)

Electronic structure of atoms: atomic spectroscopy information system

Science.gov (United States)

Kazakov, V. V.; Kazakov, V. G.; Kovalev, V. S.; Meshkov, O. I.; Yatsenko, A. S.

2017-10-01

The article presents a Russian atomic spectroscopy, information system electronic structure of atoms (IS ESA) (http://grotrian.nsu.ru), and describes its main features and options to support research and training. The database contains over 234 000 records, great attention paid to experimental data and uniform filling of the database for all atomic numbers Z, including classified levels and transitions of rare earth and transuranic elements and their ions. Original means of visualization of scientific data in the form of spectrograms and Grotrian diagrams have been proposed. Presentation of spectral data in the form of interactive color charts facilitates understanding and analysis of properties of atomic systems. The use of the spectral data of the IS ESA together with its functionality is effective for solving various scientific problems and training of specialists.

Experimental atomic physics

International Nuclear Information System (INIS)

Anon.

1985-01-01

The experimental atomic physics program within the physics division is carried out by two groups, whose reports are given in this section. Work of the accelerator atomic physics group is centered around the 6.5-MV EN tandem accelerator; consequently, most of its research is concerned with atomic processes occurring to, or initiated by, few MeV/amu heavy ions. Other activities of this group include higher energy experiments at the Holifield Heavy Ion Research Facility (HHIRF), studies of electron and positron channeling radiation, and collaborative experiments at other institutions. The second experimental group concerns itself with lower energy atomic collision physics in support of the Fusion Energy Program. During the past year, the new Electron Cyclotron Resonance Source has been completed and some of the first data from this facility is presented. In addition to these two activities in experimental atomic physics, other chapters of this report describe progress in theoretical atomic physics, experimental plasma diagnostic development, and atomic data center compilation activities

Atom-atom interactions around the band edge of a photonic crystal waveguide.

Science.gov (United States)

Hood, Jonathan D; Goban, Akihisa; Asenjo-Garcia, Ana; Lu, Mingwu; Yu, Su-Peng; Chang, Darrick E; Kimble, H J

2016-09-20

Tailoring the interactions between quantum emitters and single photons constitutes one of the cornerstones of quantum optics. Coupling a quantum emitter to the band edge of a photonic crystal waveguide (PCW) provides a unique platform for tuning these interactions. In particular, the cross-over from propagating fields [Formula: see text] outside the bandgap to localized fields [Formula: see text] within the bandgap should be accompanied by a transition from largely dissipative atom-atom interactions to a regime where dispersive atom-atom interactions are dominant. Here, we experimentally observe this transition by shifting the band edge frequency of the PCW relative to the [Formula: see text] line of atomic cesium for [Formula: see text] atoms trapped along the PCW. Our results are the initial demonstration of this paradigm for coherent atom-atom interactions with low dissipation into the guided mode.

Atomic collisions research with excited atomic species

International Nuclear Information System (INIS)

Hoogerland, M.D.; Gulley, R.J.; Colla, M.; Lu, W.; Milic, D.; Baldwin, K.G.H.; Buckman, S.J.

1999-01-01

Measurements and calculations of fundamental atomic collision and spectroscopic properties such as collision cross sections, reaction rates, transition probabilities etc. underpin the understanding and operation of many plasma and gas-discharge-based devices and phenomena, for example plasma processing and deposition. In almost all cases the complex series of reactions which sustains the discharge or plasma, or produces the reactive species of interest, has a precursor electron impact excitation, attachment, dissociation or ionisation event. These processes have been extensively studied in a wide range of atomic and molecular species and an impressive data base of collision cross sections and reaction rates now exists. However, most of these measurements are for collisions with stable atomic or molecular species which are initially in their ground electronic state. Relatively little information is available for scattering from excited states or for scattering from unstable molecular radicals. Examples of such species would be metastable excited rare gases, which are often used as buffer gases, or CF 2 radicals formed by electron impact dissociation in a CF 4 plasma processing discharge. We are interested in developing experimental techniques which will enable the quantitative study of such exotic atomic and molecular species. In this talk I would like to outline one such facility which is being used for studies of collisions with metastable He(2 3 S) atoms

Experiments with Rydberg atoms on a current-carrying atom chip

NARCIS (Netherlands)

Cisternas San Martín, N.V.

2018-01-01

On one side, atom-chip experiments have demonstrated to be a versatile tool to study quantum physics in cold atoms systems. On the other side, Rydberg atoms have exaggerated properties that makes them good candidates to study quantum information and quantum simulations protocols. In this thesis both

Atom

International Nuclear Information System (INIS)

Auffray, J.P.

1997-01-01

The atom through centuries, has been imagined, described, explored, then accelerated, combined...But what happens truly inside the atom? And what are mechanisms who allow its stability? Physicist and historian of sciences, Jean-Paul Auffray explains that these questions are to the heart of the modern physics and it brings them a new lighting. (N.C.)

Entanglement dynamics between an isolated atom and a moving atom in the cavity

International Nuclear Information System (INIS)

Xiao-Juan, Deng; Mao-Fa, Fang; Guo-Dong, Kang

2009-01-01

The entanglement dynamics between an isolated atom and a moving atom interacting with a cavity field is investigated. The results show that there appears sudden death of entanglement between the isolated atom and the moving atom and that the time of entanglement sudden death (ESD) is independent of the initial state of the system. It is interesting that the isolated atom can also entangle with a cavity field, though they do not interact with each other originally, which stems from the fact that the entanglement between the isolated atom and the moving atom may turn into the entanglement between the isolated atom and the cavity. (general)

Do atoms and anti-atoms obey the same laws of physics?

CERN Multimedia

Jeffrey Hangst

2010-01-01

ALPHA physicists have recently succeeded in trapping anti-atoms for the first time. Being able to hold on to the simplest atoms of antimatter is an important step towards the collaboration’s ultimate goal: precision spectroscopic comparison of hydrogen and antihydrogen. The question they are seeking to answer: do atoms and anti-atoms obey the same laws of physics? The Standard Model says that they must.   The ALPHA Collaboration celebrates the successful results. The ALPHA collaboration has taken it up a gear and trapped 38 atoms of antihydrogen for the first time. Antihydrogen atoms have been mass-produced at the Antiproton Decelerator (AD) since 2002, when ATHENA (ALPHA’s predecessor) and ATRAP learned how to mix clouds of antiprotons and positrons at cryogenic temperatures. However, these anti-atoms were not confined, and flew off in a few microseconds to meet their fate: annihilation with matter in the walls of the experiment. ALPHA uses antiprotons produced at...

Design and Construction of an Atomic Clock on an Atom Chip

International Nuclear Information System (INIS)

Reinhard, Friedemann

2009-01-01

We describe the design and construction of an atomic clock on an atom chip, intended as a secondary standard, with a stability in the range of few 10 -13 at 1 s. This clock is based on a two-photon transition between the hyperfine states |F = 1; m F = -1> and |2; 1> of the electronic ground state of the 87 Rb atom. This transition is interrogated using a Ramsey scheme, operating on either a cloud of thermal atoms or a Bose-Einstein condensate. In contrast to atomic fountain clocks, this clock is magnetically trapped on an atom chip. We describe a theoretical model of the clock stability and the design and construction of a dedicated apparatus. It is able to control the magnetic field at the relative 10 -5 level and features a hybrid atom chip, containing DC conductors as well as a microwave transmission line for the clock interrogation. (author)

Disposal of chemical agents and munitions stored at Pueblo Depot Activity, Colorado. Final, Phase 1: Environmental report

Energy Technology Data Exchange (ETDEWEB)

Terry, J.W.; Blasing, T.J.; Ensminger, J.T.; Johnson, R.O.; Schexnayder, S.M.; Shor, J.T.; Staub, W.P.; Tolbert, V.R.; Zimmerman, G.P.

1995-04-01

Under the Chemical Stockpile Disposal Program (CSDP), the US Army proposes to dispose of lethal chemical agents and munitions stored at eight existing Army installations in the continental United States. In 1988, the US Army issued the final programmatic environmental impact statement (FPEIS) for the CSDP. The FPEIS and the subsequent Record of Decision (ROD) identified an on-site disposal process as the preferred method for destruction of the stockpile. That is, the FPEIS determined the environmentally preferred alternative to be on-site disposal in high-temperature incinerators, while the ROD selected this alternative for implementation as the preferred method for destruction of the stockpile. In this Phase I report, the overall CSDP decision regarding disposal of the PUDA Stockpile is subjected to further analyses, and its validity at PUDA is reviewed with newer, more detailed data than those providing the basis for the conclusions in the FPEIS. The findings of this Phase I report will be factored into the scope of a site-specific environmental impact statement to be prepared for the destruction of the PUDA stockpile. The focus of this Phase I report is on those data identified as having the potential to alter the Army`s previous decision regarding disposal of the PUDA stockpile; however, several other factors beyond the scope of this Phase I report must also be acknowledged to have the potential to change or modify the Army`s decisions regarding PUDA.

Atomic switch: atom/ion movement controlled devices for beyond von-neumann computers.

Science.gov (United States)

Hasegawa, Tsuyoshi; Terabe, Kazuya; Tsuruoka, Tohru; Aono, Masakazu

2012-01-10

An atomic switch is a nanoionic device that controls the diffusion of metal ions/atoms and their reduction/oxidation processes in the switching operation to form/annihilate a conductive path. Since metal atoms can provide a highly conductive channel even if their cluster size is in the nanometer scale, atomic switches may enable downscaling to smaller than the 11 nm technology node, which is a great challenge for semiconductor devices. Atomic switches also possess novel characteristics, such as high on/off ratios, very low power consumption and non-volatility. The unique operating mechanisms of these devices have enabled the development of various types of atomic switch, such as gap-type and gapless-type two-terminal atomic switches and three-terminal atomic switches. Novel functions, such as selective volatile/nonvolatile, synaptic, memristive, and photo-assisted operations have been demonstrated. Such atomic switch characteristics can not only improve the performance of present-day electronic systems, but also enable development of new types of electronic systems, such as beyond von- Neumann computers. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Chemical reactions of recoil atoms and thermal atoms of tritium with haloid benzenes

International Nuclear Information System (INIS)

Simirskij, Yu.N.; Firsova, L.P.

1978-01-01

Radiochemical yields have been determined for the products of substitution of hydrogen atoms and halides in Cl-, Br-, and I-benzenes with tritium atoms obtained during thermal dissociation of T 2 and with recoil atoms T arising in nuclear reaction 6 Li(n, P)T. It is shown that in the series of Cl-, Br-, and I-benzenes yields of the products of substitution of halides atoms with tritium grow, whereas those of hydrogen atom substitution change only little. The correlation nature of the yields of substitution products of halide atoms with tritium remains constant in a wide range of the initial kinetic energies of T atoms for the recoil atoms with E 0 =2.7 MeV and for the completely thermolized atoms during thermal dissociation of T 2

Atomic fountain and applications

International Nuclear Information System (INIS)

Rawat, H.S.

2000-01-01

An overview of the development of working of MOT along with the basic principle of laser atom cooling and trapping is given. A technique to separate the cooled and trapped atoms from the MOT using atomic fountain technique will also be covered. The widely used technique for atomic fountain is, first to cool and trap the neutral atoms in MOT and then launch them in the vertical direction, using moving molasses technique. Using 133 Cs atomic fountain clock, time improvement of 2 to 3 order of magnitude over a conventional 133 Cs atomic clock has been observed

Generation of a slow and continuous cesium atomic beam for an atomic clock

International Nuclear Information System (INIS)

Park, Sang Eon; Lee, Ho Seong; Shin, Eun-joo; Kwon, Taeg Yong; Yang, Sung Hoon; Cho, Hyuck

2002-01-01

A thermal atomic beam from a cesium oven was slowed down by use of the Hoffnagle modified white-light cooling technique. In addition, the atomic beam was collimated by use of a two-dimensional optical molasses that was installed transverse to the atomic-beam direction. The flux of the atomic beam was 2x10 10 atoms/s, an increase of a factor of 16 as a result of the collimation. The mean longitudinal velocity was ∼24.4 m/s, and the rms velocity spread of the slowed atomic beam was ∼1 m/s. Compared with other methods, we found that the Hoffnagle method is suitable for the generation of slow atomic beams to be used in an atomic clock, which requires an ultralow magnetic field environment. This atomic beam was deflected by an angle of 30 deg. by a one-dimensional optical molasses to separate it from laser light and high-velocity atoms

Atomic inner-shell physics

International Nuclear Information System (INIS)

Crasemann, B.

1985-01-01

This book discusses: relativistic and quantum electrodynamic effects on atomic inner shells; relativistic calculation of atomic transition probabilities; many-body effects in energetic atomic transitions; Auger Electron spectrometry of core levels of atoms; experimental evaluation of inner-vacancy level energies for comparison with theory; mechanisms for energy shifts of atomic K-X rays; atomic physics research with synchrotron radiation; investigations of inner-shell states by the electron energy-loss technique at high resolution; coherence effects in electron emission by atoms; inelastic X-ray scattering including resonance phenomena; Rayleigh scattering: elastic photon scattering by bound electrons; electron-atom bremsstrahlung; X-ray and bremsstrahlung production in nuclear reactions; positron production in heavy-ion collisions, and X-ray processes in heavy-ion collisions

Effect of temperature on atom-atom collision chain length in metals

International Nuclear Information System (INIS)

Makarov, A.A.; Demkin, N.A.; Lyashchenko, B.G.

1981-01-01

Focused atom-atom collision chain lengths are calculated for fcc-crystals with account of thermal oscillations. The model of solid spheres with the Born-Merier potential has been used in the calculations. The dependence of chain lengths on the temperature, energy and movement direction of the first chain atom for Cu, Au, Ag, Pb, Ni is considered. The plot presented shows that the chain lengths strongly decrease with temperature growth, for example, for the gold at T=100 K the chain length equals up to 37 interatomic spacings, whereas at T=1000 K their length decreases down to 5 interatomic distances. The dependence of the energy loss by the chain atoms on the atom number in the chain is obtained in a wide range of crystal temperature and the primary chain atom energy [ru

Microfabricated Waveguide Atom Traps.

Energy Technology Data Exchange (ETDEWEB)

Jau, Yuan-Yu [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-09-01

A nanoscale , microfabricated waveguide structure can in - principle be used to trap atoms in well - defined locations and enable strong photon-atom interactions . A neutral - atom platform based on this microfabrication technology will be prealigned , which is especially important for quantum - control applications. At present, there is still no reported demonstration of evanescent - field atom trapping using a microfabricated waveguide structure. We described the capabilities established by our team for future development of the waveguide atom - trapping technology at SNL and report our studies to overcome the technical challenges of loading cold atoms into the waveguide atom traps, efficient and broadband optical coupling to a waveguide, and the waveguide material for high - power optical transmission. From the atomic - physics and the waveguide modeling, w e have shown that a square nano-waveguide can be utilized t o achieve better atomic spin squeezing than using a nanofiber for first time.

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard.

Science.gov (United States)

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Morán-Del Pozo, Julia Mª; Guerra-Romero, Manuel I

2014-08-13

Construction and demolition waste (CDW) constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA) and ceramic recycled aggregates (CerRA). In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08) to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation) of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW.

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard

Directory of Open Access Journals (Sweden)

Desirée Rodríguez-Robles

2014-08-01

Full Text Available Construction and demolition waste (CDW constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA and ceramic recycled aggregates (CerRA. In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08 to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW.

Cold experiment of slag centrifugal granulation by rotary atomizer: Effect of atomizer configuration

International Nuclear Information System (INIS)

Wu, Jun-Jun; Wang, Hong; Zhu, Xun; Liao, Qiang; Li, Kai

2017-01-01

Centrifugal granulation has recently been employed to produce small blast furnace slag particles, so as to recover the waste heat from the high-temperature molten blast furnace slag. An appropriate atomizer enables centrifugal granulation to become a better cost-effective process for particle production. Thus, increasing emphasis has been placed on influence of atomizer configuration on granulation. In present study, three groups of atomizers were specially designed and the granulation performance of each atomizer was experimentally tested during cold experiments. The influences of atomizer configuration on granulation modes and droplet characteristics were investigated visually. Two modified correlations were proposed to predict the granulating droplet size by means of data fitting. The results indicated that the rotary cup atomizers can inhibit the film formation in contrast to rotary disc atomizer. Moreover, atomizers with outer angle of 90° was capable of producing smaller droplets. The revised correlation as well as the newly-developed correlation including the influence of atomizer configurations, presented in good agreement with the experiment data. In addition, an analysis on atomizer design was conducted to provide a good insight for industrialization. It was recommended to adopt cup-like atomizer in granulation for its ability to produce fine particles with smaller atomizer size.

Observation of dynamic atom-atom correlation in liquid helium in real space.

Science.gov (United States)

Dmowski, W; Diallo, S O; Lokshin, K; Ehlers, G; Ferré, G; Boronat, J; Egami, T

2017-05-04

Liquid 4 He becomes superfluid and flows without resistance below temperature 2.17 K. Superfluidity has been a subject of intense studies and notable advances were made in elucidating the phenomenon by experiment and theory. Nevertheless, details of the microscopic state, including dynamic atom-atom correlations in the superfluid state, are not fully understood. Here using a technique of neutron dynamic pair-density function (DPDF) analysis we show that 4 He atoms in the Bose-Einstein condensate have environment significantly different from uncondensed atoms, with the interatomic distance larger than the average by about 10%, whereas the average structure changes little through the superfluid transition. DPDF peak not seen in the snap-shot pair-density function is found at 2.3 Å, and is interpreted in terms of atomic tunnelling. The real space picture of dynamic atom-atom correlations presented here reveal characteristics of atomic dynamics not recognized so far, compelling yet another look at the phenomenon.

Atom-atom interactions around the band edge of a photonic crystal waveguide

Science.gov (United States)

Hood, Jonathan D.; Goban, Akihisa; Asenjo-Garcia, Ana; Lu, Mingwu; Yu, Su-Peng; Chang, Darrick E.; Kimble, H. J.

2016-09-01

Tailoring the interactions between quantum emitters and single photons constitutes one of the cornerstones of quantum optics. Coupling a quantum emitter to the band edge of a photonic crystal waveguide (PCW) provides a unique platform for tuning these interactions. In particular, the cross-over from propagating fields E(x)∝e±ikxxE(x)∝e±ikxx outside the bandgap to localized fields E(x)∝e-κx|x|E(x)∝e-κx|x| within the bandgap should be accompanied by a transition from largely dissipative atom-atom interactions to a regime where dispersive atom-atom interactions are dominant. Here, we experimentally observe this transition by shifting the band edge frequency of the PCW relative to the D1D1 line of atomic cesium for N¯=3.0±0.5N¯=3.0±0.5 atoms trapped along the PCW. Our results are the initial demonstration of this paradigm for coherent atom-atom interactions with low dissipation into the guided mode.

Theoretical treatment of electron capture and excitation in two-electron system ion-atom, atom-atom collisions at low to intermediate energy

International Nuclear Information System (INIS)

Kimura, M.

1986-01-01

A review of various theoretical treatments which have been used to study electron-capture and excitation processes in two-electron-system ion-atom, atom-atom collisions at low to intermediate energy is presented. Advantages as well as limitations associated with these theoretical models in application to practical many-electron ion-atom, atom-atom collisions are specifically pointed out. Although a rigorous theoretical study of many-electron systems has just begun so that reports of theoretical calculations are scarce to date in comparison to flourishing experimental activities, some theoretical results are of great interest and provide important information for understanding collision dynamics of the system which contains many electrons. Selected examples are given for electron capture in a multiply charged ion-He collision, ion-pair formation in an atom-atom collision and alignment and orientation in a Li + + He collision. (Auth.)

Atom chip gravimeter

Science.gov (United States)

Schubert, Christian; Abend, Sven; Gebbe, Martina; Gersemann, Matthias; Ahlers, Holger; Müntinga, Hauke; Matthias, Jonas; Sahelgozin, Maral; Herr, Waldemar; Lämmerzahl, Claus; Ertmer, Wolfgang; Rasel, Ernst

2016-04-01

Atom interferometry has developed into a tool for measuring rotations [1], accelerations [2], and testing fundamental physics [3]. Gravimeters based on laser cooled atoms demonstrated residual uncertainties of few microgal [2,4] and were simplified for field applications [5]. Atomic gravimeters rely on the interference of matter waves which are coherently manipulated by laser light fields. The latter can be interpreted as rulers to which the position of the atoms is compared. At three points in time separated by a free evolution, the light fields are pulsed onto the atoms. First, a coherent superposition of two momentum states is produced, then the momentum is inverted, and finally the two trajectories are recombined. Depending on the acceleration the atoms experienced, the number of atoms detected in the output ports will change. Consequently, the acceleration can be determined from the output signal. The laser cooled atoms with microkelvin temperatures used in state-of-the-art gravimeters impose limits on the accuracy [4]. Therefore, ultra-cold atoms generated by Bose-Einstein condensation and delta-kick collimation [6,7] are expected to be the key for further improvements. These sources suffered from a low flux implying an incompatible noise floor, but a competitive performance was demonstrated recently with atom chips [8]. In the compact and robust setup constructed for operation in the drop tower [6] we demonstrated all steps necessary for an atom chip gravimeter with Bose-Einstein condensates in a ground based operation. We will discuss the principle of operation, the current performance, and the perspectives to supersede the state of the art. The authors thank the QUANTUS cooperation for contributions to the drop tower project in the earlier stages. This work is supported by the German Space Agency (DLR) with funds provided by the Federal Ministry for Economic Affairs and Energy (BMWi) due to an enactment of the German Bundestag under grant numbers DLR 50WM

Observation of atomic arrangement by using photoelectron holography and atomic stereo-photograph

International Nuclear Information System (INIS)

Matsushita, Tomohiro; Guo, Fang Zhun; Agui, Akane; Matsui, Fumihiko; Daimon, Hiroshi

2006-01-01

Both a photoelectron holography and atomic stereo-photograph are the atomic structure analysis methods on the basis of photoelectron diffraction. They have six special features such as 1) direct determination of atomic structure, 2) measurement of three dimensional atomic arrangements surrounding of specific element in the sample, 3) determination of position of atom in spite of electron cloud, 4) unnecessary of perfect periodic structure, 5) good sensitivity of structure in the neighborhood of surface and 6) information of electron structure. Photoelectron diffraction, the principle and measurement system of photoelectron holography and atomic stereo-photograph is explained. As application examples of atomic stereo-photograph, the single crystal of cupper and graphite are indicated. For examples of photoelectron holography, Si(001)2p and Ge(001)3s are explained. (S.Y.)

Atom dynamics in laser fields

International Nuclear Information System (INIS)

Jang, Su; Mi, No Gin

2004-12-01

This book introduces coherent dynamics of internal state, spread of atoms wave speed, semiclassical atoms density matrix such as dynamics equation in both still and moving atoms, excitation of atoms in movement by light, dipole radiating power, quantum statistical mechanics by atoms in movement, semiclassical atoms in movement, atoms in movement in the uniform magnetic field including effects of uniform magnetic field, atom cooling using laser such as Doppler cooling, atom traps using laser and mirrors, radiant heat which particles receive, and near field interactions among atoms in laser light.

prepared via atom transfer radical polymerization, reverse atom

Indian Academy of Sciences (India)

Synthesis and characterization of poly(2-ethylhexyl acrylate) prepared via atom transfer radical polymerization, reverse atom transfer radical polymerization and ... Zydex Industries, 25-A Gandhi Oil Mill Compound, Gorwa, Vadodara 390 016, India; Rubber Technology Centre, Indian Institute of Technology Kharagpur, ...

Advances in atomic spectroscopy

CERN Document Server

Sneddon, J

2000-01-01

This fifth volume of the successful series Advances in Atomic Spectroscopy continues to discuss and investigate the area of atomic spectroscopy.It begins with a description of the use of various atomic spectroscopic methods and applications of speciation studies in atomic spectroscopy. The emphasis is on combining atomic spectroscopy with gas and liquid chromatography. In chapter two the authors describe new developments in tunable lasers and the impact they will have on atomic spectroscopy. The traditional methods of detection, such as photography and the photomultiplier, and how they are being replaced by new detectors is discussed in chapter three. The very active area of glow discharge atomic spectrometry is presented in chapter four where, after a brief introduction and historical review, the use of glow discharge lamps for atomic spectroscopy and mass spectrometry are discussed. Included in this discussion is geometry and radiofrequency power. The future of this source in atomic spectroscopy is also dis...

Atomic and molecular manipulation

CERN Document Server

Mayne, Andrew J

2011-01-01

Work with individual atoms and molecules aims to demonstrate that miniaturized electronic, optical, magnetic, and mechanical devices can operate ultimately even at the level of a single atom or molecule. As such, atomic and molecular manipulation has played an emblematic role in the development of the field of nanoscience. New methods based on the use of the scanning tunnelling microscope (STM) have been developed to characterize and manipulate all the degrees of freedom of individual atoms and molecules with an unprecedented precision. In the meantime, new concepts have emerged to design molecules and substrates having specific optical, mechanical and electronic functions, thus opening the way to the fabrication of real nano-machines. Manipulation of individual atoms and molecules has also opened up completely new areas of research and knowledge, raising fundamental questions of "Optics at the atomic scale", "Mechanics at the atomic scale", Electronics at the atomic scale", "Quantum physics at the atomic sca...

Small-angle scattering of ions or atoms by atomic hydrogen

International Nuclear Information System (INIS)

Franco, V.

1982-01-01

A theory for small-angle scattering of arbitrary medium- or high-energy atoms or ions by atomic hydrogen is described. Results are obtained in terms of the known closed-form and easily calculable Glauber-approximation scattering amplitudes for electron-hydrogen collisions and for collisions between the nucleus (treated as one charged particle) of the ion or atom and the hydrogen atom, and in terms of the transition form factor of the arbitrary ion or atom. Applications are made to the angular differential cross sections for the excitation of atomic hydrogen to its n = 2 states by singly charged ground-state helium ions having velocities of roughly between 1/2 and 1 a.u. The differential cross sections are obtained in terms of electron-hydrogen amplitudes and the known He + ground-state form factor. Comparisons are made with other calculations and with recent measurements. The results are in good agreement with the data. It is seen that the effect of the He + electron is to produce significant constructive interference at most energies

Mechanism of formation and spatial distribution of lead atoms in quartz tube atomizers

Science.gov (United States)

Johansson, M.; Baxter, D. C.; Ohlsson, K. E. A.; Frech, W.

1997-05-01

The cross-sectional and longitudinal spatial distributions of lead atoms in a quartz tube (QT) atomizers coupled to a gas chromatograph have been investigated. A uniform analyte atom distribution over the cross-section was found in a QT having an inner diameter (i.d.) of 7 mm, whereas a 10 mm i.d. QT showed an inhomogeneous distribution. These results accentuate the importance of using QTs with i.d.s below 10 mm to fulfil the prerequirement of the Beer—Lambert law to avoid bent calibration curves. The influence of the make up gas on the formation of lead atoms from alkyllead compounds has been studied, and carbon monoxide was found equally efficient in promoting free atom formation as hydrogen. This suggests that hydrogen radicals are not essential for mediating the atomization of alkyllead in QT atomizers at ˜ 1200 K. Furthermore, thermodynamic equilibrium calculations describing the investigated system were performed supporting the experimental results. Based on the presented data, a mechanism for free lead atom formation in continuously heated QT atomizers is proposed; thermal atomization occurs under thermodynamic equilibrium conditions in a reducing gas. The longitudinal atom distribution has been further investigated applying other make up gases, N 2 and He. These results show the effect of the influx of atmospheric oxygen on the free lead atom formation. Calculations of the partial pressure of oxygen in the atomizer gas phase assuming thermodynamic equilibrium have been undertaken using a convective-diffusional model.

Modern atomic physics

CERN Document Server

Natarajan, Vasant

2015-01-01

Much of our understanding of physics in the last 30-plus years has come from research on atoms, photons, and their interactions. Collecting information previously scattered throughout the literature, Modern Atomic Physics provides students with one unified guide to contemporary developments in the field. After reviewing metrology and preliminary material, the text explains core areas of atomic physics. Important topics discussed include the spontaneous emission of radiation, stimulated transitions and the properties of gas, the physics and applications of resonance fluorescence, coherence, cooling and trapping of charged and neutral particles, and atomic beam magnetic resonance experiments. Covering standards, a different way of looking at a photon, stimulated radiation, and frequency combs, the appendices avoid jargon and use historical notes and personal anecdotes to make the topics accessible to non-atomic physics students. Written by a leader in atomic and optical physics, this text gives a state-of-the...

0.75 atoms improve the clock signal of 10,000 atoms

DEFF Research Database (Denmark)

Kruse, I.; Lange, K.; Peise, Jan

2017-01-01

Since the pioneering work of Ramsey, atom interferometers are employed for precision metrology, in particular to measure time and to realize the second. In a classical interferometer, an ensemble of atoms is prepared in one of the two input states, whereas the second one is left empty. In this case.......75 atoms to improve the clock sensitivity of 10,000 atoms by 2.05 dB. The SQL poses a significant limitation for today's microwave fountain clocks, which serve as the main time reference. We evaluate the major technical limitations and challenges for devising a next generation of fountain clocks based...... on atomic squeezed vacuum....

Multipolar electrostatics for proteins: atom-atom electrostatic energies in crambin.

Science.gov (United States)

Yuan, Yongna; Mills, Matthew J L; Popelier, Paul L A

2014-02-15

Accurate electrostatics necessitates the use of multipole moments centered on nuclei or extra point charges centered away from the nuclei. Here, we follow the former alternative and investigate the convergence behavior of atom-atom electrostatic interactions in the pilot protein crambin. Amino acids are cut out from a Protein Data Bank structure of crambin, as single amino acids, di, or tripeptides, and are then capped with a peptide bond at each side. The atoms in the amino acids are defined through Quantum Chemical Topology (QCT) as finite volume electron density fragments. Atom-atom electrostatic energies are computed by means of a multipole expansion with regular spherical harmonics, up to a total interaction rank of L = ℓA+ ℓB + 1 = 10. The minimum internuclear distance in the convergent region of all the 15 possible types of atom-atom interactions in crambin that were calculated based on single amino acids are close to the values calculated from di and tripeptides. Values obtained at B3LYP/aug-cc-pVTZ and MP2/aug-cc-pVTZ levels are only slightly larger than those calculated at HF/6-31G(d,p) level. This convergence behavior is transferable to the well-known amyloid beta polypeptide Aβ1-42. Moreover, for a selected central atom, the influence of its neighbors on its multipole moments is investigated, and how far away this influence can be ignored is also determined. Finally, the convergence behavior of AMBER becomes closer to that of QCT with increasing internuclear distance. Copyright © 2013 Wiley Periodicals, Inc.

Antiprotonic-hydrogen atoms

International Nuclear Information System (INIS)

Batty, C.J.

1989-07-01

Experimental studies of antiprotonic-hydrogen atoms have recently made great progress following the commissioning of the low energy antiproton facility (LEAR) at CERN in 1983. At the same time our understanding of the atomic cascade has increased considerably through measurements of the X-ray spectra. The life history of the p-bar-p atom is considered in some detail, from the initial capture of the antiproton when stopping in hydrogen, through the atomic cascade with the emission of X-rays, to the final antiproton annihilation and production of mesons. The experiments carried out at LEAR are described and the results compared with atomic cascade calculations and predictions of strong interaction effects. (author)

Mechanical properties of hot mix asphalt made with recycled aggregates from reclaimed construction and demolition debris

Directory of Open Access Journals (Sweden)

Taibo, J.

2007-03-01

Full Text Available The mix design for asphalt mixtures containing recycled aggregates from construction and demolition debris was evaluated. The tests conducted to characterize the mechanical behaviour of these mixtures showed that the mechanical properties of mixtures with recycled and virgin aggregate are similar. The asphalt mixtures containing recycled aggregate proved to have lower resistance to water action. Nonetheless, recycled aggregate was found to be potentially usable in asphalt mixtures if higher quality materials are selected and such low resistance is corrected. This will call for expanding upon the preliminary work described in the present article.En este trabajo se dosificaron mezclas bituminosas fabricadas con áridos reciclados de residuos de construcción y demolición. Se realizaron una serie de ensayos que permitieron caracterizar el comportamiento mecánico de estas mezclas. Los parámetros mecánicos de las mezclas con áridos reciclados son similares a los de las mezclas fabricadas únicamente con áridos naturales de cantera. Sin embargo, las mezclas bituminosas con áridos reciclados tuvieron un mal comportamiento frente a la disminución de la resistencia por pérdida de cohesión por la acción del agua. No obstante, mediante la selección de materiales de mejor calidad y corrección de este mal comportamiento, existen posibilidades de utilizar áridos reciclados en mezclas bituminosas. Para ello será necesario ampliar la primera aproximación realizada en este artículo.

Atoms - molecules - nuclei. Vol. 1

International Nuclear Information System (INIS)

Otter, G.; Honecker, R.

1993-01-01

This first volume covers the following topics: Wave-particle dualism, classical atomic physics; the Schroedinger equation, angular momentum in quantum physics, one-electron atoms and many-electron atoms with atomic structure, atomic spectra, exotic atoms, influence of electric and magnetic fields

Amplitudes and state parameters from ion- and atom-atom excitation processes

International Nuclear Information System (INIS)

Andersen, T.; Horsdal-Pedersen, E.

1984-01-01

This chapter examines single collisions between two atomic species, one of which is initially in a 1 S state (there is only one initial spin channel). The collisions are characterized by a definite scattering plane and a definite orientation. Topics considered include an angular correlation between scattered particles and autoionization electrons or polarized photons emitted from states excited in atomic collisions (photon emission, electron emission, selectivity excited target atoms), experimental methods for obtaining information on the alignment and orientation parameters of atoms or ions excited in specific collisions, results of experiments and numerical calculations (quasi-oneelectron systems, He + -He collisions, other collision systems), and future aspects and possible applications of the polarizedphoton, scattered-particle coincidence techniques to atomic spectroscopy

‘Which-way’ collective atomic spin excitation among atomic ensembles by photon indistinguishability

International Nuclear Information System (INIS)

Zhang Guowan; Bian Chenglin; Chen, L Q; Ou, Z Y; Zhang Weiping

2012-01-01

In spontaneous Raman scattering in an atomic ensemble, a collective atomic spin wave is created in correlation with the Stokes field. When the Stokes photons from two or more such atomic ensembles are made indistinguishable, a ‘which-way’ collective atomic spin excitation is generated among the independent atomic ensembles. We demonstrate this phenomenon experimentally by reading out the atomic spin excitations and observing interference between the read-out beams. When a single-photon projective measurement is made on the indistinguishable Stokes photons, this simple scheme can be used to entangle independent atomic ensembles. Compared to other currently used methods, this scheme can be easily scaled up and has greater efficiency. (paper)

Atomic interferometry

International Nuclear Information System (INIS)

Baudon, J.; Robert, J.

2004-01-01

Since the theoretical works of L. De Broglie (1924) and the famous experiment of Davisson and Germer (1927), we know that a wave is linked with any particle of mass m by the relation λ = h/(mv), where λ is the wavelength, v the particle velocity and h is the Planck constant. The basic principle of the interferometry of any material particle, atom, molecule or aggregate is simple: using a simple incident wave, several mutually consistent waves (with well-defined relative phases) are generated and controllable phase-shifts are introduced between them in order to generate a wave which is the sum of the previous waves. An interference figure is obtained which consists in a succession of dark and bright fringes. The atomic interferometry is based on the same principle but involves different techniques, different wave equations, but also different beams, sources and correlations which are described in this book. Because of the small possible wavelengths and the wide range of possible atomic interactions, atomic interferometers can be used in many domains from the sub-micron lithography to the construction of sensors like: inertial sensors, gravity-meters, accelerometers, gyro-meters etc. The first chapter is a preliminary study of the space and time diffraction of atoms. The next chapters is devoted to the description of slit, light separation and polarization interferometers, and the last chapter treats of the properties of Bose-Einstein condensates which are interesting in atomic interferometry. (J.S.)

Clarifying atomic weights: A 2016 four-figure table of standard and conventional atomic weights

Science.gov (United States)

Coplen, Tyler B.; Meyers, Fabienne; Holden, Norman E.

2017-01-01

To indicate that atomic weights of many elements are not constants of nature, in 2009 and 2011 the Commission on Isotopic Abundances and Atomic Weights (CIAAW) of the International Union of Pure and Applied Chemistry (IUPAC) replaced single-value standard atomic weight values with atomic weight intervals for 12 elements (hydrogen, lithium, boron, carbon, nitrogen, oxygen, magnesium, silicon, sulfur, chlorine, bromine, and thallium); for example, the standard atomic weight of nitrogen became the interval [14.00643, 14.00728]. CIAAW recognized that some users of atomic weight data only need representative values for these 12 elements, such as for trade and commerce. For this purpose, CIAAW provided conventional atomic weight values, such as 14.007 for nitrogen, and these values can serve in education when a single representative value is needed, such as for molecular weight calculations. Because atomic weight values abridged to four figures are preferred by many educational users and are no longer provided by CIAAW as of 2015, we provide a table containing both standard atomic weight values and conventional atomic weight values abridged to four figures for the chemical elements. A retrospective review of changes in four-digit atomic weights since 1961 indicates that changes in these values are due to more accurate measurements over time or to the recognition of the impact of natural isotopic fractionation in normal terrestrial materials upon atomic weight values of many elements. Use of the unit “u” (unified atomic mass unit on the carbon mass scale) with atomic weight is incorrect because the quantity atomic weight is dimensionless, and the unit “amu” (atomic mass unit on the oxygen scale) is an obsolete term: Both should be avoided.

Spatial distribution of organic pollutants in industrial construction and demolition waste and their mutual interaction on an abandoned pesticide manufacturing plant.

Science.gov (United States)

Huang, Sheng; Zhao, Xin; Sun, Yanqiu; Ma, Jianli; Gao, Xiaofeng; Xie, Tian; Xu, Dongsheng; Yu, Yi; Zhao, Youcai

2016-04-01

A comprehensive field investigation of organic pollutants was examined in industrial construction and demolition waste (ICDW) inside an abandoned pesticide manufacturing plant. Concentrations of eight types of pesticides, a metabolite and two intermediates were studied. The ICDW was under severe and long-term contamination by organophosphorus, intermediates and pyrethroid pesticide with mean concentrations of 23,429, 3538 and 179.4 mg kg(-1), respectively. FT-IR analysis suggested that physical absorption and chemical bonding were their mutual interaction forms. Patterns of total pesticide spatial distribution showed good correlations with manufacturing processes spreading all over the plant both in enclosed workshops and in residues randomly dumped outside, while bricks and coatings were the most vulnerable to pollutants. Ultimately the fate of the OPPs was diversified as the immersion of ICDW in water largely transferred the pollutants into aquatic systems while exposure outside did not largely lead to pesticide degradation. The adoption of centralized collections for the disposal of wastes could only eliminate part of the contaminated ICDW, probably due to lack of knowledge and criteria. Correlation matrix and cluster analysis indicated that regulated disposal and management of polluted ICDW was effective, thus presenting the requirement for its appropriate disposal.

Three-dimensional atom localization via electromagnetically induced transparency in a three-level atomic system.

Science.gov (United States)

Wang, Zhiping; Cao, Dewei; Yu, Benli

2016-05-01

We present a new scheme for three-dimensional (3D) atom localization in a three-level atomic system via measuring the absorption of a weak probe field. Owing to the space-dependent atom-field interaction, the position probability distribution of the atom can be directly determined by measuring the probe absorption. It is found that, by properly varying the parameters of the system, the probability of finding the atom in 3D space can be almost 100%. Our scheme opens a promising way to achieve high-precision and high-efficiency 3D atom localization, which provides some potential applications in laser cooling or atom nano-lithography via atom localization.

Atomic hydrogen reactor

International Nuclear Information System (INIS)

Massip de Turville, C.M.D.

1982-01-01

Methods are discussed of generating heat in an atomic hydrogen reactor which involve; the production of atomic hydrogen by an electrical discharge, the capture of nascent neutrons from atomic hydrogen in a number of surrounding steel alloy tubes having a high manganese content to produce 56 Mn, the irradiation of atomic hydrogen by the high energy antineutrinos from the beta decay of 56 Mn to yield nascent neutrons, and the removal of the heat generated by the capture of nascent neutrons by 55 Mn and the beta decay of 56 Mn. (U.K.)

Investigation of phosphorus atomization using high-resolution continuum source electrothermal atomic absorption spectrometry

International Nuclear Information System (INIS)

Dessuy, Morgana B.; Vale, Maria Goreti R.; Lepri, Fabio G.; Welz, Bernhard; Heitmann, Uwe

2007-01-01

The atomization of phosphorus in electrothermal atomic absorption spectrometry has been investigated using a high-resolution continuum source atomic absorption spectrometer and atomization from a graphite platform as well as from a tantalum boat inserted in a graphite tube. A two-step atomization mechanism is proposed for phosphorus, where the first step is a thermal dissociation, resulting in a fast atomization signal early in the atomization stage, and the second step is a slow release of phosphorus atoms from the graphite tube surface following the adsorption of molecular phosphorus at active sites of the graphite surface. Depending on experimental conditions only one of the mechanisms or both might be active. In the absence of a modifier and with atomization from a graphite or tantalum platform the second mechanism appears to be dominant, whereas in the presence of sodium fluoride as a modifier both mechanisms are observed. Intercalation of phosphorus into the graphite platform in the condensed phase has also been observed; this phosphorus, however, appears to be permanently trapped in the structure of the graphite and does not contribute to the absorption signal

Coexistence of photonic and atomic Bose-Einstein condensates in ideal atomic gases

Directory of Open Access Journals (Sweden)

N. Boichenko

2015-12-01

Full Text Available We have studied conditions of photon Bose-Einstein condensate formation that is in thermodynamic equilibrium with ideal gas of two-level Bose atoms below the degeneracy temperature. Equations describing thermodynamic equilibrium in the system were formulated; critical temperatures and densities of photonic and atomic gas subsystems were obtained analytically. Coexistence conditions of these photonic and atomic Bose-Einstein condensates were found. There was predicted the possibility of an abrupt type of photon condensation in the presence of Bose condensate of ground-state atoms: it was shown that the slightest decrease of the temperature could cause a significant gathering of photons in the condensate. This case could be treated as a simple model of the situation known as "stopped light" in cold atomic gas. We also showed how population inversion of atomic levels can be created by lowering the temperature. The latter situation looks promising for light accumulation in atomic vapor at very low temperatures.

Atomic force microscopy. A new method for atom identification and manipulation

International Nuclear Information System (INIS)

Abe, Masayuki; Sugimoto, Yoshiaki; Morita, Seizo

2007-01-01

Frequency modulation atomic force microscopy (FM-AFM) is a scanning probe technique that detects the interaction forces between the outermost atom of a sharp tip and the atoms at a surface to image the sample surface. It is expected that the FM-AFM can cover the research field which scanning tunneling microscopy does not provide. In this article, we would introduce FM-AFM experiments applied to site-specific force measurements and atom manipulation, including how to solve the problems to achieve precise FM-AFM measurements. (author)

Design considerations regarding an atomizer for multi-element electrothermal atomic absorption spectrometry

Energy Technology Data Exchange (ETDEWEB)

Katskov, Dmitri A., E-mail: katskovda@tut.ac.za [Department of Chemistry, Tshwane University of Technology, Private Bag X680, Pretoria 0001 (South Africa); Sadagov, Yuri M. [All-Russian Scientific Research Institute of Optical and Physical Measurements (VNIIOFI), Ozernaya St. 46, Moscow 119361 (Russian Federation)

2011-06-15

The methodology of simultaneous multi-element electrothermal atomic absorption spectrometry (ETAAS-Electrothermal Atomic Absorption Spectrometry) stipulates rigid requirements to the design and operation of the atomizer. It must provide high degree of atomization for the group of analytes, invariant respective to the vaporization kinetics and heating ramp residence time of atoms in the absorption volume and absence of memory effects from major sample components. For the low resolution spectrometer with a continuum radiation source the reduced compared to traditional ETAAS (Electrothermal Atomic Absorption Spectrometry) sensitivity should be, at least partially, compensated by creating high density of atomic vapor in the absorption pulse. The sought-for characteristics were obtained for the 18 mm in length and 2.5 mm in internal diameter longitudinally heated graphite tube atomizer furnished with 2-4.5 mg of ring shaped carbon fiber yarn collector. The collector located next to the sampling port provides large substrate area that helps to keep the sample and its residue in the central part of the tube after drying. The collector also provides a 'platform' effect that delays the vaporization and stipulates vapor release into absorption volume having already stabilized gas temperature. Due to the shape of external surface of the tube, presence of collector and rapid (about 10 {sup o}C/ms) heating, an inverse temperature distribution along the tube is attained at the beginnings of the atomization and cleaning steps. The effect is employed for cleaning of the atomizer using the set of short maximum power heating pulses. Preparation, optimal maintenance of the atomizer and its compliance to the multi-element determination requirements are evaluated and discussed. The experimental setup provides direct simultaneous determination of large group of element within 3-4 order concentration range. Limits of detection are close to those for sequential single element

Ionization of highly excited atoms by atomic particle impact

International Nuclear Information System (INIS)

Smirnov, B.M.

1976-01-01

The ionization of a highly excited atom by a collision with an atom or molecule is considered. The theory of these processes is presented and compared with experimental data. Cross sections and ionization potential are discussed. 23 refs

Two-dimensional atom localization via probe absorption in a four-level atomic system

International Nuclear Information System (INIS)

Wang Zhi-Ping; Ge Qiang; Ruan Yu-Hua; Yu Ben-Li

2013-01-01

We have investigated the two-dimensional (2D) atom localization via probe absorption in a coherently driven four-level atomic system by means of a radio-frequency field driving a hyperfine transition. It is found that the detecting probability and precision of 2D atom localization can be significantly improved via adjusting the system parameters. As a result, our scheme may be helpful in laser cooling or the atom nano-lithography via atom localization

Calibration of atomic trajectories in a large-area dual-atom-interferometer gyroscope

Science.gov (United States)

Yao, Zhan-Wei; Lu, Si-Bin; Li, Run-Bing; Luo, Jun; Wang, Jin; Zhan, Ming-Sheng

2018-01-01

We propose and demonstrate a method for calibrating atomic trajectories in a large-area dual-atom-interferometer gyroscope. The atom trajectories are monitored by modulating and delaying the Raman transition, and they are precisely calibrated by controlling the laser orientation and the bias magnetic field. To improve the immunity to the gravity effect and the common phase noise, the symmetry and the overlap of two large-area atomic interference loops are optimized by calibrating the atomic trajectories and by aligning the Raman-laser orientations. The dual-atom-interferometer gyroscope is applied in the measurement of the Earth's rotation. The sensitivity is 1.2 ×10-6 rad s -1 Hz-1/2, and the long-term stability is 6.2 ×10-8 rad/s at 2000 s.

A study of atomic interaction between suspended nanoparticles and sodium atoms in liquid sodium

International Nuclear Information System (INIS)

Saito, Jun-ichi; Ara, Kuniaki

2010-01-01

A feasibility study of suppression of the chemical reactivity of sodium itself using an atomic interaction between nanoparticles and sodium atoms has been carried out. We expected that the atomic interaction strengthens when the nanoparticle metal is the transition element which has a major difference in electronegativity from sodium. We also calculated the atomic interaction between nanoparticle and sodium atoms. It became clear that the atomic bond between the nanoparticle atom and the sodium atom is larger than that between sodium atoms, and the charge transfer takes place to the nanoparticle atom from the sodium atom. Using sodium with suspended nanoparticles, the fundamental physical properties related to the atomic interaction were investigated to verify the atomic bond. The surface tension of sodium with suspended nanoparticles increased, and the evaporation rate of sodium with suspended nanoparticles also decreased compared with that of sodium. Therefore the presence of the atomic interaction between nanoparticles and sodium was verified from these experiments. Because the fundamental physical property changes by the atomic interaction, we expected changes in the chemical reactivity characteristics. The chemical reaction properties of sodium with suspended nanoparticles with water were investigated experimentally. The released reaction heat and the reaction rate of sodium with suspended nanoparticles were reduced than those of sodium. The influence of the charge state of nanoparticle on the chemical process with water was theoretically investigated to speculate on the cause of reaction suppression. The potential energy in both primary and side reactions changed by the charge transfer, and the free energy of activation of the reaction with water increased. Accordingly, the reaction barrier also increased. This suggests there is a possibility of the reduction in the reaction of sodium by the suspension of nanoparticles. Consequently the possibility of the

Influence of the atomic structure on the quantum state of sputtered Ir atoms

International Nuclear Information System (INIS)

Bastiaansen, J.; Philipsen, V.; Lievens, P.; Silverans, R.E.; Vandeweert, E.

2004-01-01

The probability of the ejection of a neutral atom in a specific quantum state after keV-ion beam sputtering is often interpreted in terms of the interaction between the atomic states of the escaping atom and the electronic states of the solid. In this work, we examined this interplay in the sputtering of iridium as this element has--unlike the elements employed in previous investigations--a complex atomic structure due to strong configuration interactions. Double-resonant two-photon laser ionization is used to probe the sputtered Ir atoms yielding information about the probability for an ejected atom to populate a specific atomic state and its escape velocity. The qualitative features of the corresponding population partition and state-selective velocity distributions show the influence of the excitation energy and the electronic structure of the different atomic states. A comparison is made between the experimental data and predictions from the resonant electron transfer description

Quality Assessment of Mixed and Ceramic Recycled Aggregates from Construction and Demolition Wastes in the Concrete Manufacture According to the Spanish Standard †

Science.gov (United States)

Rodríguez-Robles, Desirée; García-González, Julia; Juan-Valdés, Andrés; Pozo, Julia Mª Morán-del; Guerra-Romero, Manuel I

2014-01-01

Construction and demolition waste (CDW) constitutes an increasingly significant problem in society due to the volume generated, rendering sustainable management and disposal problematic. The aim of this study is to identify a possible reuse option in the concrete manufacturing for recycled aggregates with a significant ceramic content: mixed recycled aggregates (MixRA) and ceramic recycled aggregates (CerRA). In order to do so, several tests are conducted in accordance with the Spanish Code on Structural Concrete (EHE-08) to determine the composition in weight and physic-mechanical characteristics (particle size distributions, fine content, sand equivalent, density, water absorption, flakiness index, and resistance to fragmentation) of the samples for the partial inclusion of the recycled aggregates in concrete mixes. The results of these tests clearly support the hypothesis that this type of material may be suitable for such partial replacements if simple pretreatment is carried out. Furthermore, this measure of reuse is in line with European, national, and regional policies on sustainable development, and presents a solution to the environmental problem caused by the generation of CDW. PMID:28788164

AtomPy: A Cloud Atomic-data Service for Astrophysical Applications

Science.gov (United States)

Mendoza, Claudio; Boswell, J. S.; Bautista, M.

2013-06-01

Apart from our long-term commitment to the computing of accurate atomic data for astrophysical applications, we have also been interested in the problems of data access and dissemination. In this respect, one of us took part in the developments of TIPTOPbase [1, 2, 3], the astrophysical opacity server referred to as OPserver [4, 5], and, more recently, of the Virtual Atomic and Molecular Data Center [6, 7]. Our present effort is now with the establishment of a cloud atomic data web service, AtomPy, implemented by means of SOAP web services, Google Drive spreadsheets and Python modules. In the present poster we will describe the outline of this ambitious project, illustrated with some prototypes that are already operational.

Atom and Bond Fukui Functions and Matrices: A Hirshfeld-I Atoms-in-Molecule Approach.

Science.gov (United States)

Oña, Ofelia B; De Clercq, Olivier; Alcoba, Diego R; Torre, Alicia; Lain, Luis; Van Neck, Dimitri; Bultinck, Patrick

2016-09-19

The Fukui function is often used in its atom-condensed form by isolating it from the molecular Fukui function using a chosen weight function for the atom in the molecule. Recently, Fukui functions and matrices for both atoms and bonds separately were introduced for semiempirical and ab initio levels of theory using Hückel and Mulliken atoms-in-molecule models. In this work, a double partitioning method of the Fukui matrix is proposed within the Hirshfeld-I atoms-in-molecule framework. Diagonalizing the resulting atomic and bond matrices gives eigenvalues and eigenvectors (Fukui orbitals) describing the reactivity of atoms and bonds. The Fukui function is the diagonal element of the Fukui matrix and may be resolved in atom and bond contributions. The extra information contained in the atom and bond resolution of the Fukui matrices and functions is highlighted. The effect of the choice of weight function arising from the Hirshfeld-I approach to obtain atom- and bond-condensed Fukui functions is studied. A comparison of the results with those generated by using the Mulliken atoms-in-molecule approach shows low correlation between the two partitioning schemes. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Symmetric Atom–Atom and Ion–Atom Processes in Stellar Atmospheres

Directory of Open Access Journals (Sweden)

Vladimir A. Srećković

2017-12-01

Full Text Available We present the results of the influence of two groups of collisional processes (atom–atom and ion–atom on the optical and kinetic properties of weakly ionized stellar atmospheres layers. The first type includes radiative processes of the photodissociation/association and radiative charge exchange, the second one the chemi-ionisation/recombination processes with participation of only hydrogen and helium atoms and ions. The quantitative estimation of the rate coefficients of the mentioned processes were made. The effect of the radiative processes is estimated by comparing their intensities with those of the known concurrent processes in application to the solar photosphere and to the photospheres of DB white dwarfs. The investigated chemi-ionisation/recombination processes are considered from the viewpoint of their influence on the populations of the excited states of the hydrogen atom (the Sun and an M-type red dwarf and helium atom (DB white dwarfs. The effect of these processes on the populations of the excited states of the hydrogen atom has been studied using the general stellar atmosphere code, which generates the model. The presented results demonstrate the undoubted influence of the considered radiative and chemi- ionisation/recombination processes on the optical properties and on the kinetics of the weakly ionized layers in stellar atmospheres.

Atomic physics

CERN Document Server

Born, Max

1969-01-01

The Nobel Laureate's brilliant exposition of the kinetic theory of gases, elementary particles, the nuclear atom, wave-corpuscles, atomic structure and spectral lines, electron spin and Pauli's principle, quantum statistics, molecular structure and nuclear physics. Over 40 appendices, a bibliography, numerous figures and graphs.

The Effect of Vibration Characteristics on the Atomization Rate in a Micro-Tapered Aperture Atomizer

Directory of Open Access Journals (Sweden)

Qiufeng Yan

2018-03-01

Full Text Available Because little is known about the atomization theory of a micro-tapered aperture atomizer, we investigated the vibration characteristics of this type of atomizer. The atomization mechanism of a micro-tapered aperture atomizer was described, and the atomization rate equation was deduced. As observed via microscopy, the angle of the micro-tapered aperture changes with the applied voltage, which proved the existence of a dynamic cone angle. The forward and reverse atomization rates were measured at various voltages, and the influence of the micro-tapered aperture and its variation on the atomization rate was characterized. The resonance frequency of the piezoelectric vibrator was obtained using a laser vibrometer, and the atomization rates were measured at each resonance frequency. From experiments, we found that the atomization rates at the first five resonance frequencies increased as the working frequency increased. At the fifth resonance frequency (121.1 kHz, the atomization rate was maximized (0.561 mL/min, and at the sixth resonance frequency (148.3 kHz, the atomization rate decreased significantly (0.198 mL/min. The experimental results show that the vibration characteristics of the piezoelectric vibrator have a relatively strong impact on the atomization rate. This research is expected to contribute to the manufacture of micro-tapered aperture atomizers.