WorldWideScience

Sample records for atmospheric plasma deposition

  1. Modified drug release using atmospheric pressure plasma deposited siloxane coatings

    Science.gov (United States)

    Dowling, D. P.; Maher, S.; Law, V. J.; Ardhaoui, M.; Stallard, C.; Keenan, A.

    2016-09-01

    This pilot study evaluates the potential of atmospheric plasma polymerised coatings to modify the rate of drug release from polymeric substrates. The antibiotic rifampicin was deposited in a prototype multi-layer drug delivery system, consisting of a nebulized layer of active drug between a base layer of TEOS deposited on a plastic substrate (polystyrene) and an overlying layer of plasma polymerised PDMS. The polymerised TEOS and PDMS layers were deposited using a helium atmospheric plasma jet system. Elution of rifampicin was measured using UV-VIS spectroscopy, in addition to a antimicrobial well diffusion assay with an established indicator organism. The multi-layered plasma deposited coatings significantly extended the duration of release of the rifampicin from 24 h for the uncoated polymer to 144 h for the coated polymer.

  2. Plasma reactor for deposition of carbon nanowalls at atmospheric pressure

    Science.gov (United States)

    Dimitrov, Zh; Mitev, D.; Kiss'ovski, Zh

    2016-10-01

    In this study a novel plasma reactor for deposition of carbon nanowalls at atmospheric pressure is constructed and characterized. A low power microwave discharge is used as a plasma source and working gas of Ar/H2/CH4 gas mixture. The substrate is heated by plasma flame and its temperature is in the range 600-700 C. The chemical composition of the plasma and the gas mixture effect on the concentration of the various particles in the plasma is investigated by optical emission spectroscopy. The emission spectrum of the plasma jet in Ar/H2/CH4 mixture shows the presence of carbon (Swan band) and an intensive line of CH (388 nm), which are necessary species for deposition of carbon nanostructures. Additional voltage in the range from -20 V to -100 V is applied in order to ensure the vertical growth of graphene walls. Results of deposited carbon nanostructures on metal substrate are shown.

  3. Atmospheric Plasma Deposition of Diamond-like Carbon Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Ladwig, Angela

    2008-01-23

    material that may be treated. The deposition of DLC at atmospheric pressure has been demonstrated by several researchers. Izake, et al [53] and Novikov and Dymont [54] have demonstrated an electrochemical process that is carried out with organic compounds such as methanol and acetylene dissolved in ammonia. This process requires that the substrates be immersed in the liquid [53-54]. The atmospheric pressure deposition of DLC was also demonstrated by Kulik, et al. utilizing a plasma torch. However, this process requires operating temperatures in excess of 800 oC [55]. In this report, we investigate the deposition of diamond-like carbon films using a low temperature, atmospheric pressure plasma-enhanced chemical vapor deposition (PECVD) process. The films were characterized by solid-state carbon-13 nuclear magnetic resonance (13C NMR) and found to have a ratio of sp2 to sp3 carbon of 43 to 57%. The films were also tested for adhesion, coefficient of friction, and dielectric strength.

  4. Gas permeation barriers deposited by atmospheric pressure plasma enhanced atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Hoffmann, Lukas, E-mail: lhoffmann@uni-wuppertal.de; Theirich, Detlef; Hasselmann, Tim; Räupke, André; Schlamm, Daniel; Riedl, Thomas, E-mail: t.riedl@uni-wuppertal.de [Institute of Electronic Devices, University of Wuppertal, Rainer-Gruenter-Str. 21, 42119 Wuppertal (Germany)

    2016-01-15

    This paper reports on aluminum oxide (Al{sub 2}O{sub 3}) thin film gas permeation barriers fabricated by atmospheric pressure atomic layer deposition (APPALD) using trimethylaluminum and an Ar/O{sub 2} plasma at moderate temperatures of 80 °C in a flow reactor. The authors demonstrate the ALD growth characteristics of Al{sub 2}O{sub 3} films on silicon and indium tin oxide coated polyethylene terephthalate. The properties of the APPALD-grown layers (refractive index, density, etc.) are compared to that deposited by conventional thermal ALD at low pressures. The films films deposited at atmospheric pressure show water vapor transmission rates as low as 5 × 10{sup −5} gm{sup −2}d{sup −1}.

  5. Characterisation of PMMA/ATH Layers Realised by Means of Atmospheric Pressure Plasma Powder Deposition

    Directory of Open Access Journals (Sweden)

    Lena M. Wallenhorst

    2015-01-01

    Full Text Available We report on the characteristics of aluminium trihydrate filled poly(methyl methacrylate composite (PMMA/ATH coatings realised by plasma deposition at atmospheric pressure. For this purpose, PMMA/ATH powder was fed to a plasma jet where the process and carrier gas was compressed air. The deposited coatings were investigated by X-ray photoelectron spectroscopy and water contact angle measurements. Further, the raw material was characterised before deposition. It was found that, with respect to the raw material, aluminium was uncovered in the course of the plasma deposition process which can be explained by plasma-induced etching of the PMMA matrix. As a result, the wettability of plasma-deposited PMMA/ATH was significantly increased. Even though a uniform coating film could not be realised as ascertained by confocal laser scanning microscopy, the deposited coatings feature notably enhanced characteristics which could be advantageous for further processing.

  6. Simulation of low-temperature, atmospheric-pressure plasma enhanced chemical vapor deposition reactors

    OpenAIRE

    Lorant, Christophe; Descamps, Pierre; De Wilde, Juray; 1st BeLux workshop on “Coating, Materials, surfaces and Interfaces

    2014-01-01

    The simulation of low-temperature, atmospheric-pressure plasma enhanced chemical vapor deposition reactors is challenging due to the coupling of the fluid dynamics, the chemical reactions and the electric field and the stiffness of the resulting mathematical system. The model equations and the rigorous model reduction to reduce the stiffness are addressed in this paper. Considering pure nitrogen plasma, simulations with two configurations are discussed.

  7. Atmospheric Plasma Deposition of SiO2 Films for Adhesion Promoting Layers on Titanium

    Directory of Open Access Journals (Sweden)

    Liliana Kotte

    2014-12-01

    Full Text Available This paper evaluates the deposition of silica layers at atmospheric pressure as a pretreatment for the structural bonding of titanium (Ti6Al4V, Ti15V3Cr3Sn3Al in comparison to an anodizing process (NaTESi process. The SiO2 film was deposited using the LARGE plasma source, a linearly extended DC arc plasma source and applying hexamethyldisiloxane (HMDSO as a precursor. The morphology of the surface was analyzed by means of SEM, while the characterization of the chemical composition of deposited plasma layers was done by XPS and FTIR. The long-term durability of bonded samples was evaluated by means of a wedge test in hot/wet condition. The almost stoichiometric SiO2 film features a good long-term stability and a high bonding strength compared to the films produced with the wet-chemical NaTESi process.

  8. Deposition of hybrid organic-inorganic composite coatings using an atmospheric plasma jet system.

    Science.gov (United States)

    Dembele, Amidou; Rahman, Mahfujur; Reid, Ian; Twomey, Barry; MacElroy, J M Don; Dowling, Denis P

    2011-10-01

    The objective of this study is to investigate the influence of alcohol addition on the incorporation of metal oxide nanoparticles into nm thick siloxane coatings. Titanium oxide (TiO2) nanoparticles with diameters of 30-80 nm were incorporated into an atmospheric plasma deposited tetramethylorthosilicate (TMOS) siloxane coating. The TMOS/TiO2 coating was deposited using the atmospheric plasma jet system known as PlasmaStream. In this system the liquid precursor/nanoparticle mixture is nebulised into the plasma. It was observed that prior to being nebulised the TiO2 particles agglomerated and settled over time in the TMOS/TiO2 mixture. In order to obtain a more stable nanoparticle/TMOS suspension the addition of the alcohols methanol, octanol and pentanol to this mixture was investigated. The addition of each of these alcohols was found to stabilise the nanoparticle suspension. The effect of the alcohol was therefore assessed with respect to the properties of the deposited coatings. It was observed that coatings deposited from TMOS/TiO2, with and without the addition of methanol were broadly similar. In contrast the coatings deposited with octanol and pentanol addition to the TMOS/TiO2 mixture were significantly thicker, for a given set of deposition parameters and were also more homogeneous. This would indicate that the alcohol precursor was incorporated into the plasma polymerised siloxane. The incorporation of the organic functionality from the alcohols was confirmed from FTIR spectra of the coatings. The difference in behaviour with alcohol type is likely to be due to the lower boiling point of methanol (65 degrees C), which is lower than the maximum plasma temperature measured at the jet orifice (77 degrees C). This temperature is significantly lower than the 196 degrees C and 136 degrees C boiling points of octanol and pentanol respectively. The friction of the coatings was determined using the Pin-on-disc technique. The more organic coatings deposited with

  9. An Evaluation of Atmospheric-pressure Plasma for the Cost-Effective Deposition of Antireflection Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Rob Sailer; Guruvenket Srinivasan; Kyle W. Johnson; Douglas L. Schulz

    2010-04-01

    Atmospheric-pressure plasma deposition (APPD) has previously been used to deposit various functional materials including polymeric surface modification layers, transparent conducting oxides, and photo catalytic materials. For many plasma polymerized coatings, reaction occurs via free radical mechanism where the high energy electrons from the plasma activate the olefinic carbon-carbon double bonds - a typical functional group in such precursors. The precursors for such systems are typically inexpensive and readily available and have been used in vacuum PECVD previously. The objectives are to investigate: (1) the effect of plasma power, gas composition and substrate temperature on the Si-based film properties using triethylsilane(TES) as the precursor; and (2) the chemical, mechanical, and optical properties of several experimental matrices based on Design of Experiment (DOE) principals. A simple APPD route has been utilized to deposit Si based films from an inexpensive precursor - Triethylsilane (TES). Preliminary results indicates formation of Si-C & Si-O and Si-O, Si-C & Si-N bonds with oxygen and nitrogen plasmas respectively. N{sub 2}-O{sub 2} plasma showed mixed trend; however oxygen remains a significant portion of all films, despite attempts to minimize exposure to atmosphere. SiN, SiC, and SiO ratios can be modified by the reaction conditions resulting in differing film properties. SE studies revealed that films with SiN bond possess refractive index higher than coatings with Si-O/Si-C bonds. Variable angle reflectance studies showed that SiOCN coatings offer AR properties; however thickness and refractive index optimization of these coatings remains necessary for application as potential AR coatings.

  10. An Evaluation of Atmospheric-pressure Plasma for the Cost-Effective Deposition of Antireflection Coatings

    Energy Technology Data Exchange (ETDEWEB)

    Rob Sailer; Guruvenket Srinivasan; Kyle W. Johnson; Douglas L. Schulz

    2010-04-01

    Atmospheric-pressure plasma deposition (APPD) has previously been used to deposit various functional materials including polymeric surface modification layers, transparent conducting oxides, and photo catalytic materials. For many plasma polymerized coatings, reaction occurs via free radical mechanism where the high energy electrons from the plasma activate the olefinic carbon-carbon double bonds - a typical functional group in such precursors. The precursors for such systems are typically inexpensive and readily available and have been used in vacuum PECVD previously. The objectives are to investigate: (1) the effect of plasma power, gas composition and substrate temperature on the Si-based film properties using triethylsilane(TES) as the precursor; and (2) the chemical, mechanical, and optical properties of several experimental matrices based on Design of Experiment (DOE) principals. A simple APPD route has been utilized to deposit Si based films from an inexpensive precursor - Triethylsilane (TES). Preliminary results indicates formation of Si-C & Si-O and Si-O, Si-C & Si-N bonds with oxygen and nitrogen plasmas respectively. N{sub 2}-O{sub 2} plasma showed mixed trend; however oxygen remains a significant portion of all films, despite attempts to minimize exposure to atmosphere. SiN, SiC, and SiO ratios can be modified by the reaction conditions resulting in differing film properties. SE studies revealed that films with SiN bond possess refractive index higher than coatings with Si-O/Si-C bonds. Variable angle reflectance studies showed that SiOCN coatings offer AR properties; however thickness and refractive index optimization of these coatings remains necessary for application as potential AR coatings.

  11. Plasma polymers deposited in atmospheric pressure dielectric barrier discharges: Influence of process parameters on film properties

    Energy Technology Data Exchange (ETDEWEB)

    Fricke, Katja, E-mail: k.fricke@inp-greifswald.de [Leibniz Institute for Plasma Science and Technology e.V. (INP Greifswald), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Girard-Lauriault, Pierre-Luc [Plasma Processing Laboratory, Department of Chemical Engineering, McGill University, 3610 rue University, Montreal, QC H3A 0C5 (Canada); Weltmann, Klaus-Dieter [Leibniz Institute for Plasma Science and Technology e.V. (INP Greifswald), Felix-Hausdorff-Str. 2, 17489 Greifswald (Germany); Wertheimer, Michael R. [Department of Engineering Physics, École Polytechnique de Montréal, Box 6079, Station Centre-Ville, Montreal, QC H3C 3A7 (Canada)

    2016-03-31

    We present results on the deposition of plasma polymer (PP) films in a dielectric barrier discharge system fed with mixtures of argon or nitrogen carrier gas plus different hydrocarbon precursors, where the latter possess different carbon-to-hydrogen ratios: CH{sub 4} < C{sub 2}H{sub 6} < C{sub 2}H{sub 4} = C{sub 3}H{sub 6} < C{sub 2}H{sub 2}. The influence of precursor gas mixture and flow rate, excitation frequency, and absorbed power on PP film compositions and properties has been investigated. The discharge was characterized by electrical measurements, while the chemical compositions and structures of coatings were analysed by X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, total combustion, and elastic recoil detection analyses, the latter two for determining carbon-to-hydrogen ratios. Scanning electron microscopy was used to study the coatings' morphology, and profilometry for evaluating deposition rates. - Highlights: • Atmospheric pressure DBD is used to deposit organic hydrocarbon films. • High deposition rates can be achieved by varying the power and/or gas mixture ratio. • Process parameters affect the films' surface chemical composition and morphology. • Deposited films are not soluble in aqueous environment. • No delamination of coatings produced from argon plasma.

  12. Fabrication of transparent antifouling thin films with fractal structure by atmospheric pressure cold plasma deposition.

    Science.gov (United States)

    Miyagawa, Hayato; Yamauchi, Koji; Kim, Yoon-Kee; Ogawa, Kazufumi; Yamaguchi, Kenzo; Suzaki, Yoshifumi

    2012-12-21

    Antifouling surface with both superhydrophobicity and oil-repellency has been fabricated on glass substrate by forming fractal microstructure(s). The fractal microstructure was constituted by transparent silica particles of 100 nm diameter and transparent zinc-oxide columns grown on silica particles by atmospheric pressure cold plasma deposition. The sample surface was coated with a chemically adsorbed monomolecular layer. We found that one sample has the superhydrophobic ability with a water droplet contact angle of more than 150°, while another sample has a high transmittance of more than 85% in a wavelength range from 400 to 800 nm.

  13. Atmospheric pressure plasma deposition of antimicrobial coatings on non-woven textiles

    Science.gov (United States)

    Nikiforov, Anton Yu.; Deng, Xiaolong; Onyshchenko, Iuliia; Vujosevic, Danijela; Vuksanovic, Vineta; Cvelbar, Uros; De Geyter, Nathalie; Morent, Rino; Leys, Christophe

    2016-08-01

    A simple method for preparation of nanoparticle incorporated non-woven fabric with high antibacterial efficiency has been proposed based on atmospheric pressure plasma process. In this work direct current plasma jet stabilized by fast nitrogen flow was used as a plasma deposition source. Three different types of the nanoparticles (silver, copper and zinc oxide nanoparticles) were employed as antimicrobial agents. X-ray photoelectron spectroscopy (XPS) measurements have shown a positive chemical shift observed for Ag 3d 5/2 (at 368.1 eV) suggests that silver nanoparticles (AgNPs) are partly oxidized during the deposition. The surface chemistry and the antibacterial activity of the samples against Staphylococcus aureus and Escherichia coli were investigated and analyzed. It is shown that the samples loaded with nanoparticles of Ag and Cu and having the barrier layer of 10 nm characterized by almost 97% of bacterial reduction whereas the samples with ZnO nanoparticles provide 86% reduction of Staphylococcus aureus. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  14. Chain Assemblies from Nanoparticles Synthesized by Atmospheric Pressure Plasma Enhanced Chemical Vapor Deposition: The Computational View.

    Science.gov (United States)

    Mishin, Maxim V; Zamotin, Kirill Y; Protopopova, Vera S; Alexandrov, Sergey E

    2015-12-01

    This article refers to the computational study of nanoparticle self-organization on the solid-state substrate surface with consideration of the experimental results, when nanoparticles were synthesised during atmospheric pressure plasma enhanced chemical vapor deposition (AP-PECVD). The experimental study of silicon dioxide nanoparticle synthesis by AP-PECVD demonstrated that all deposit volume consists of tangled chains of nanoparticles. In certain cases, micron-sized fractals are formed from tangled chains due to deposit rearrangement. This work is focused on the study of tangled chain formation only. In order to reveal their formation mechanism, a physico-mathematical model was developed. The suggested model was based on the motion equation solution for charged and neutral nanoparticles in the potential fields with the use of the empirical interaction potentials. In addition, the computational simulation was carried out based on the suggested model. As a result, the influence of such experimental parameters as deposition duration, particle charge, gas flow velocity, and angle of gas flow was found. It was demonstrated that electrical charges carried by nanoparticles from the discharge area are not responsible for the formation of tangled chains from nanoparticles, whereas nanoparticle kinetic energy plays a crucial role in deposit morphology and density. The computational results were consistent with experimental results.

  15. Diamond synthesis at atmospheric pressure by microwave capillary plasma chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Hemawan, Kadek W.; Gou, Huiyang; Hemley, Russell J. [Geophysical Laboratory, Carnegie Institution of Washington, 5251 Broad Branch Rd., NW, Washington, DC 20015 (United States)

    2015-11-02

    Polycrystalline diamond has been synthesized on silicon substrates at atmospheric pressure, using a microwave capillary plasma chemical vapor deposition technique. The CH{sub 4}/Ar plasma was generated inside of quartz capillary tubes using 2.45 GHz microwave excitation without adding H{sub 2} into the deposition gas chemistry. Electronically excited species of CN, C{sub 2}, Ar, N{sub 2}, CH, H{sub β}, and H{sub α} were observed in the emission spectra. Raman measurements of deposited material indicate the formation of well-crystallized diamond, as evidenced by the sharp T{sub 2g} phonon at 1333 cm{sup −1} peak relative to the Raman features of graphitic carbon. Field emission scanning electron microscopy images reveal that, depending on the growth conditions, the carbon microstructures of grown films exhibit “coral” and “cauliflower-like” morphologies or well-facetted diamond crystals with grain sizes ranging from 100 nm to 10 μm.

  16. Trends in surface engineering of biomaterials: atmospheric pressure plasma deposition of coatings for biomedical applications

    Science.gov (United States)

    da Ponte, G.; Sardella, E.; Fanelli, F.; D'Agostino, R.; Favia, P.

    2011-11-01

    Cold plasma processes for surface engineering of biomaterials and biomedical devices are traditionally performed at low pressure; more and more, though, surface modification plasma processes at atmospheric pressure are also gaining popularity. This short review is aimed to list briefly atmospheric pressure plasma processes reported, in the last decade, for adapting the surface of materials to the best interactions with cells, bacteria and biomolecules.

  17. Antifouling Transparent ZnO Thin Films Fabricated by Atmospheric Pressure Cold Plasma Deposition

    Science.gov (United States)

    Suzaki, Yoshifumi; Du, Jinlong; Yuji, Toshifumi; Miyagawa, Hayato; Ogawa, Kazufumi

    2015-09-01

    One problem with outdoor-mounted solar panels is that power generation efficiency is reduced by face plate dirt; a problem with electronic touch panels is the deterioration of screen visibility caused by finger grease stains. To solve these problems, we should fabricate antifouling surfaces which have superhydrophobic and oil-repellent properties without spoiling the transparency of the transparent substrate. In this study, an antifouling surface with both superhydrophobicity and oil-repellency was fabricated on a glass substrate by forming a fractal microstructure. The fractal microstructure was constituted of transparent silica particles 100 nm in diameter and transparent zinc-oxide columns grown on silica particles through atmospheric pressure cold plasma deposition; the sample surface was coated with a chemically adsorbed monomolecular layer. Samples were obtained which had a superhydrophobic property (with a water droplet contact angle of more than 150°) and a high average transmittance of about 90% (with wavelengths ranging from 400 nm to 780 nm).

  18. Amorphous carbon film deposition on inner surface of tubes using atmospheric pressure pulsed filamentary plasma source

    CERN Document Server

    Pothiraja, Ramasamy; Awakowicz, Peter

    2011-01-01

    Uniform amorphous carbon film is deposited on the inner surface of quartz tube having the inner diameter of 6 mm and the outer diameter of 8 mm. A pulsed filamentary plasma source is used for the deposition. Long plasma filaments (~ 140 mm) as a positive discharge are generated inside the tube in argon with methane admixture. FTIR-ATR, XRD, SEM, LSM and XPS analyses give the conclusion that deposited film is amorphous composed of non-hydrogenated sp2 carbon and hydrogenated sp3 carbon. Plasma is characterized using optical emission spectroscopy, voltage-current measurement, microphotography and numerical simulation. On the basis of observed plasma parameters, the kinetics of the film deposition process is discussed.

  19. Hybrid layers deposited by an atmospheric pressure plasma process for corrosion protection of galvanized steel.

    Science.gov (United States)

    Del Frari, D; Bour, J; Bardon, J; Buchheit, O; Arnoult, C; Ruch, D

    2010-04-01

    Finding alternative treatments to reproduce anticorrosion properties of chromated coatings is challenging since both physical barrier and self-healing effects are needed. Siloxane based treatments are known to be a promising way to achieve physical barrier coatings, mainly plasma polymerized hexamethyldisiloxane (ppHMDSO). In addition, it is known that cerium-based coatings can also provide corrosion protection of metals by means of self-healing effect. In this frame, innovative nanoAlCeO3/ppHMDSO layers have thus been deposited and studied. These combinations allow to afford a good physical barrier effect and active properties. Liquid siloxane and cerium-based particles mixture is atomized and introduced as precursors into a carrier gas. Gas mixture is then injected into an atmospheric pressure dielectric barrier discharge (DBD) where plasma polymerization of the siloxane precursor occurs. The influence of cerium concentration on the coating properties is investigated: coating structure and topography have been studied by scanning electron microscopy (SEM) and interferometry, and corrosion resistance of these different coatings is compared by electrochemistry techniques: polarization curves and electrochemical impedance spectroscopy (EIS). Potential self-healing property afforded by cerium in the layer was studied by associating EIS measurements and nanoscratch controlled damaging. Among the different combinations investigated, mixing of plasma polymerized HMDSO and AICeO3 nanoparticles seems to give promising results with a good physical barrier and interesting electroactive properties. Indeed, corrosion currents measured on such coatings are almost as low as those measured with the chromated film. Combination of nanoscratch damaging of layers with EIS experiments to investigate self-healing also allow to measure the active protection property of such layers.

  20. Novel thin films deposited on electrospun PCL scaffolds by atmospheric pressure plasma jet for L929 fibroblast cell cultivation

    Science.gov (United States)

    Gozutok, M.; Baitukha, A.; Arefi-Khonsari, F.; Turkoglu Sasmazel, H.

    2016-11-01

    This paper reports on the deposition of PCL homopolymers and poly ɛ-caprolactone-polyethylene glycol (PCL-PEG) copolymers by atmospheric pressure plasma jet (APPJ) onto electrospun PCL scaffolds for improving L929 fibroblast cell growth. Polymer deposited scaffolds showed better stability as well as lower CA as compared to those treated with APPJ in Ar alone used as the carrier gas to introduce the precursors due to the formation of polar groups generated during the plasma treatment, such as -OH and/or -COO. Average fiber and porosity sizes were calculated by using SEM photographs and the ImageJ Launcher Software program and higher values were observed for both PCL and PCL-PEG deposited scaffolds than the untreated electrospun PCL scaffolds. XPS analysis showed that C1s% content decreased for PCL deposited (from 82.4% to 71.0%) and PCL-PEG deposited (from 82.4% to 57.7%) and O1s% composition increased for PCL deposited (from 17.6% to 29.0%) and PCL-PEG deposited (from 17.6% to 42.3%) compared to the untreated one. XPS results proved more incorporation of oxygen moieties on the deposited surfaces than the untreated samples giving rise to more hydrophilic surfaces to the deposited ones. Standard in vitro MTT test, Giemsa staining, fluorescence and CLSM imaging techniques were used for the determination of cell viability, adhesion and proliferation. Cell culture experiments showed that PCL-PEG deposited electrospun PCL scaffolds had the most promising cell adhesion, proliferation and growth among the treated scaffolds. The increased average fiber diameter caused by deposition as well as oxygen containing polar groups formed on the surfaces due to the radicals present in the plasma atmosphere provided higher surface area and functionality, respectively, for cells to attach, yielding better biocompatibility performance.

  1. Enhanced adhesion over aluminum solid substrates by controlled atmospheric plasma deposition of amine-rich primers.

    Science.gov (United States)

    Petersen, Julien; Fouquet, Thierry; Michel, Marc; Toniazzo, Valérie; Dinia, Aziz; Ruch, David; Bomfim, João A S

    2012-02-01

    Controlled chemical modification of aluminum surface is carried by atmospheric plasma polymerization of allylamine. The amine-rich coatings are characterized and tested for their behavior as adhesion promoter. The adhesion strength of aluminum-epoxy assemblies is shown to increase according to primary amino group content and coating thickness, which in turn can be regulated by plasma power parameters, allowing tailoring the coating chemical properties. The increase in adherence can be correlated to the total and primary amino group contents in the film, indicating covalent bonding of epoxy groups to the primer as the basis of the mechanical improvement.

  2. Deposition of silica protected luminescent layers of Eu:GdVO{sub 4} nanoparticles assisted by atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Moretti, Elisa, E-mail: elisa.moretti@unive.it [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca' Foscari Venezia, INSTM Venice Research Unit, Via Torino 155/B, 30172 Mestre, Venezia (Italy); Pizzol, Giorgia [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca' Foscari Venezia, INSTM Venice Research Unit, Via Torino 155/B, 30172 Mestre, Venezia (Italy); Fantin, Marina; Enrichi, Francesco; Scopece, Paolo [Nanofab-Veneto Nanotech, Via delle Industrie 5, 30175 Marghera, Venezia (Italy); Nuñez, Nuria O.; Ocaña, Manuel [Instituto de Ciencia de Materiales de Sevilla, CSIC-US, Americo Vespucio 49, 41092, Isla de la Cartuja, Sevilla (Spain); Benedetti, Alvise [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca' Foscari Venezia, INSTM Venice Research Unit, Via Torino 155/B, 30172 Mestre, Venezia (Italy); Polizzi, Stefano [Dipartimento di Scienze Molecolari e Nanosistemi, Università Ca' Foscari Venezia, INSTM Venice Research Unit, Via Torino 155/B, 30172 Mestre, Venezia (Italy); Centro di Microscopia Elettronica “Giovanni Stevanato”, Università Ca' Foscari Venezia, Via Torino 155/B, 30172 Mestre, Venezia (Italy)

    2016-01-01

    Eu:GdVO{sub 4} nanophosphors with an average size of 60 nm, synthesized by a facile solvothermal method, were deposited on monocrystalline silicon wafers by a spray-coating technique with artworks anti-counterfeiting applications in mind. Atmospheric pressure plasma jet (APPJ) was used to deposit a silica-based layer on top of the nanometric luminescent layer, in order to improve its adhesion to the substrate and to protect it from the environment. The nanophosphors were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). Coating composition was investigated by Fourier transform infrared spectroscopy (FT-IR) and its morphology was characterized by scanning electron microscopy (FEG-SEM). The film thickness was evaluated by means of ellipsometry and adhesion was estimated by a peeling test. Luminescent properties of the nanophosphors deposited and fixed on silicon wafers were also measured. The whole layer resulted well-adhered to the silicon substrate, transparent and undetectable in the presence of visible light, but easily activated by UV light source. - Highlights: • Luminescent films were obtained by spray deposition of Eu:GdVO{sub 4} nanophosphors. • Plasma jet deposition of SiO{sub 2} fixed the nanophosphors on the substrate. • Optical properties of nanophosphors were preserved after deposition-fixing process. • Films well-adhered to the substrate, even after a scotch tape peeling test and a scratch test.

  3. Deposition of SiOx on Metal Surface with a DBD Plasma Gun at Atmospheric Pressure for Corrosion Prevention

    Institute of Scientific and Technical Information of China (English)

    HAN Erli; CHEN Qiang; ZHANG Yuefei; CHEN Fei; GE Yuanjing

    2007-01-01

    In this study,SiOx films were deposited by a dielectric barrier discharge(DBD)plasma gun at an atmospheric pressure.The relationship of the film structures with plasma powers Was investigated by Fourier transform infrared spectroscopy(FTIR),and scanning electron microscope(SEM).It was shown that an uniform and cross-linking structure film was formed by the DBD gun.As an application,the SiOx films were deposited on a carbon steel surface for the anti-corrosion purpose.The experiment was carried out in a 0.1 M NaC1 solution.It Was found that a very good anti-corrosive property was obtained,i.e.,the corrosion rate Was decreased c.a.15 times in 5% NaC1 solution compared to the non-SiOx coated steel,as detected by the potentiodynamic polarization measurement.

  4. Orientating layers with adjustable pretilt angles for liquid crystals deposited by a linear atmospheric pressure plasma source

    Energy Technology Data Exchange (ETDEWEB)

    Jian, Shih-Jie; Kou, Chwung-Shan [Department of Physics, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Hwang, Jennchang [Department of Materials Science and Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan (China); Lee, Chein-Dhau; Lin, Wei-Cheng [Material and Chemical Research Laboratories/Industrial Technology Research Institute, Hsinchu 30140, Taiwan (China)

    2013-06-15

    A method for controlling the pretilt angles of liquid crystals (LC) was developed. Hexamethyldisiloxane polymer films were first deposited on indium tin oxide coated glass plates using a linear atmospheric pressure plasma source. The films were subsequently treated with the rubbing method for LC alignment. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy measurements were used to characterize the film composition, which could be varied to control the surface energy by adjusting the monomer feed rate and input power. The results of LC alignment experiments showed that the pretilt angle continuously increased from 0 Degree-Sign to 90 Degree-Sign with decreasing film surface energy.

  5. Enhanced photocatalytic properties of nanoclustered P-doped TiO2 films deposited by advanced atmospheric plasma jet.

    Science.gov (United States)

    Seo, Hyung-Kee; Elliott, C Michael; Ansari, S G

    2012-09-01

    A facile preparation of P-doped TiO2 nanoclusters onto fluorine-doped tin oxide (FTO) glass by an advanced atmospheric plasma jet (AAP jet) is reported here. Titanium tetrachloride (TiCl4) and phosphorus trichloride (PCl3) were used as precursors. Radio frequencies were used to generate plasma at fix powder with Argon as carrier gas. Films were deposited at 500 degrees C for 10 minutes. For comparison, as-prepared, annealed and deposited at 500 degrees C samples were studied for chemical/physical properties by scanning electron microscopy (SEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). Optical properties were studied by using UV-Vis spectroscopy which indicated a reduction in optical band with P-doping. The rhodamine B (Rh-B) degradation by P-doped TiO2 deposited at 500 degrees C showed enhanced degradation efficiency than that of annealed TiO2. The suggested deposition method appears to be suitable for the synthesis of photocatalyst with proper control over dopants.

  6. Oxidation Behavior of Titanium Carbonitride Coating Deposited by Atmospheric Plasma Spray Synthesis

    Science.gov (United States)

    Zhu, Lin; He, Jining; Yan, Dianran; Liao, Hanlin; Zhang, Nannan

    2017-08-01

    Abstract: As a high-hardness and anti-frictional material, titanium carbonitride (TiCN) thick coatings or thin films are increasingly being used in many industrial fields. In the present study, TiCN coatings were obtained by atmospheric plasma spray synthesis or reactive plasma spray. In order to promote the reaction between the Ti particles and reactive gases, a home-made gas tunnel was mounted on a conventional plasma gun to perform the spray process. The oxidation behavior of the TiCN coatings under different temperatures in static air was carefully investigated. As a result, when the temperature was over 700 °C, the coatings suffered from serious oxidation, and finally they were entirely oxidized to the TiO2 phase at 1100 °C. The principal oxidation mechanism was clarified, indicating that the oxygen can permeate into the defects and react with TiCN at high temperatures. In addition, concerning the use of a TiCN coating in high-temperature conditions, the microhardness of the oxidized coatings at different treatment temperatures was also evaluated.

  7. Deposition of Antimicrobial Copper-Rich Coatings on Polymers by Atmospheric Pressure Jet Plasmas

    Directory of Open Access Journals (Sweden)

    Jana Kredl

    2016-04-01

    Full Text Available Inanimate surfaces serve as a permanent reservoir for infectious microorganisms, which is a growing problem in areas in everyday life. Coating of surfaces with inorganic antimicrobials, such as copper, can contribute to reduce the adherence and growth of microorganisms. The use of a DC operated air plasma jet for the deposition of copper thin films on acrylonitrile butadiene styrene (ABS substrates is reported. ABS is a widespread material used in consumer applications, including hospitals. The influence of gas flow rate and input current on thin film characteristics and its bactericidal effect have been studied. Results from X-ray photoelectron spectroscopy (XPS and atomic force microscopy confirmed the presence of thin copper layers on plasma-exposed ABS and the formation of copper particles with a size in the range from 20 to 100 nm, respectively. The bactericidal properties of the copper-coated surfaces were tested against Staphylococcus aureus. A reduction in growth by 93% compared with the attachment of bacteria on untreated samples was observed for coverage of the surface with 7 at. % copper.

  8. Back corona enhanced organic film deposition inside an Atmospheric Pressure Weakly Ionized Plasma reactor

    Science.gov (United States)

    Islam, Rokibul; Xie, Shuzheng; Englund, Karl; Pedrow, Patrick

    2014-10-01

    A grounded screen with short needle-like protrusions has been designed to generate back corona in an Atmospheric Pressure Weakly Ionized Plasma (APWIP) reactor. The grounded screen with protrusions is placed downstream at a variable gap length from an array of needles that is energized with 60 Hz high voltage. The excitation voltage is in the range 0--10 kV RMS and the feed gas mixture consists of argon and acetylene. A Lecroy 9350AL 500 MHz digital oscilloscope is used to monitor the reactor voltage and current using a resistive voltage divider and a current viewing resistor, respectively. The current signal contains many positive and negative current pulses associated with corona discharge. Analysis of the current signal shows asymmetry between positive and negative corona discharge currents. Photographs show substantial back corona generated near the tips of the protrusions situated at the grounded screen. The back corona activates via bond scission acetylene radicals that are transported downstream to form a plasma-polymerized film on a substrate positioned downstream from the grounded screen. The oscillograms will be used to generate corona mode maps that show the nature of the corona discharge as a function of gap spacing, applied voltage and many other reactor parameters.

  9. Glacial atmospheric phosphorus deposition

    Science.gov (United States)

    Kjær, Helle Astrid; Dallmayr, Remi; Gabrieli, Jacopo; Goto-Azuma, Kumiko; Hirabayashi, Motohiro; Svensson, Anders; Vallelonga, Paul

    2016-04-01

    Phosphorus in the atmosphere is poorly studied and thus not much is known about atmospheric phosphorus and phosphate transport and deposition changes over time, though it is well known that phosphorus can be a source of long-range nutrient transport, e.g. Saharan dust transported to the tropical forests of Brazil. In glacial times it has been speculated that transport of phosphorus from exposed shelves would increase the ocean productivity by wash out. However whether the exposed shelf would also increase the atmospheric load to more remote places has not been investigated. Polar ice cores offer a unique opportunity to study the atmospheric transport of aerosols on various timescales, from glacial-interglacial periods to recent anthropogenic influences. We have for the first time determined the atmospheric transport of phosphorus to the Arctic by means of ice core analysis. Both total and dissolved reactive phosphorus were measured to investigate current and past atmospheric transport of phosphorus to the Arctic. Results show that glacial cold stadials had increased atmospheric total phosphorus mass loads of 70 times higher than in the past century, while DRP was only increased by a factor of 14. In the recent period we find evidence of a phosphorus increase over the past 50 yrs in ice cores close to human occupation likely correlated to forest fires. References: Kjær, Helle Astrid, et al. "Continuous flow analysis method for determination of dissolved reactive phosphorus in ice cores." Environmental science & technology 47.21 (2013): 12325-12332. Kjær, Helle Astrid, et al. "Greenland ice cores constrain glacial atmospheric fluxes of phosphorus." Journal of Geophysical Research: Atmospheres120.20 (2015).

  10. Atmospheric pressure plasma-initiated chemical vapor deposition (AP-PiCVD) of poly(diethylallylphosphate) coating: a char-forming protective coating for cellulosic textile.

    Science.gov (United States)

    Hilt, Florian; Boscher, Nicolas D; Duday, David; Desbenoit, Nicolas; Levalois-Grützmacher, Joëlle; Choquet, Patrick

    2014-01-01

    An innovative atmospheric pressure chemical vapor deposition method toward the deposition of polymeric layers has been developed. This latter involves the use of a nanopulsed plasma discharge to initiate the free-radical polymerization of an allyl monomer containing phosphorus (diethylallylphosphate, DEAP) at atmospheric pressure. The polymeric structure of the film is evidence by mass spectrometry. The method, highly suitable for the treatment of natural biopolymer substrate, has been carried out on cotton textile to perform the deposition of an efficient and conformal protective coating.

  11. Development of open air silicon deposition technology by silane-free atmospheric pressure plasma enhanced chemical transport under local ambient gas control

    Science.gov (United States)

    Naito, Teruki; Konno, Nobuaki; Yoshida, Yukihisa

    2016-07-01

    Open air silicon deposition was performed by combining silane-free atmospheric pressure plasma-enhanced chemical transport and a newly developed local ambient gas control technology. The effect of air contamination on silicon deposition was investigated using a vacuum chamber, and the allowable air contamination level was confirmed to be 3 ppm. The capability of the local ambient gas control head was investigated numerically and experimentally. A safe and clean process environment with air contamination less than 1 ppm was achieved. Combining these technologies, a microcrystalline silicon film was deposited in open air, the properties of which were comparable to those of silicon films deposited in a vacuum chamber.

  12. Sub-micro a-C:H patterning of silicon surfaces assisted by atmospheric-pressure plasma-enhanced chemical vapor deposition

    Science.gov (United States)

    Boileau, Alexis; Gries, Thomas; Noël, Cédric; Perito Cardoso, Rodrigo; Belmonte, Thierry

    2016-11-01

    Micro and nano-patterning of surfaces is an increasingly popular challenge in the field of the miniaturization of devices assembled via top-down approaches. This study demonstrates the possibility of depositing sub-micrometric localized coatings—spots, lines or even more complex shapes—made of amorphous hydrogenated carbon (a-C:H) thanks to a moving XY stage. Deposition was performed on silicon substrates using chemical vapor deposition assisted by an argon atmospheric-pressure plasma jet. Acetylene was injected into the post-discharge region as a precursor by means of a glass capillary with a sub-micrometric diameter. A parametric study was carried out to study the influence of the geometric configurations (capillary diameter and capillary-plasma distance) on the deposited coating. Thus, the patterns formed were investigated by scanning electron microscopy and atomic force microscopy. Furthermore, the chemical composition of large coated areas was investigated by Fourier transform infrared spectroscopy according to the chosen atmospheric environment. The observed chemical bonds show that reactions of the gaseous precursor in the discharge region and both chemical and morphological stability of the patterns after treatment are strongly dependent on the surrounding gas. Various sub-micrometric a-C:H shapes were successfully deposited under controlled atmospheric conditions using argon as inerting gas. Overall, this new process of micro-scale additive manufacturing by atmospheric plasma offers unusually high-resolution at low cost.

  13. Atmospheric pressure plasma chemical vapor deposition reactor for 100 mm wafers, optimized for minimum contamination at low gas flow rates

    Energy Technology Data Exchange (ETDEWEB)

    Anand, Venu, E-mail: venuanand@cense.iisc.ernet.in, E-mail: venuanand83@gmail.com; Shivashankar, S. A. [Centre for Nano Science and Engineering (CeNSE), Indian Institute of Science (IISc), Bangalore 560012 (India); Nair, Aswathi R.; Mohan Rao, G. [Department of Instrumentation and Applied Physics (IAP), Indian Institute of Science (IISc), Bangalore 560012 (India)

    2015-08-31

    Gas discharge plasmas used for thinfilm deposition by plasma-enhanced chemical vapor deposition (PECVD) must be devoid of contaminants, like dust or active species which disturb the intended chemical reaction. In atmospheric pressure plasma systems employing an inert gas, the main source of such contamination is the residual air inside the system. To enable the construction of an atmospheric pressure plasma (APP) system with minimal contamination, we have carried out fluid dynamic simulation of the APP chamber into which an inert gas is injected at different mass flow rates. On the basis of the simulation results, we have designed and built a simple, scaled APP system, which is capable of holding a 100 mm substrate wafer, so that the presence of air (contamination) in the APP chamber is minimized with as low a flow rate of argon as possible. This is examined systematically by examining optical emission from the plasma as a function of inert gas flow rate. It is found that optical emission from the plasma shows the presence of atmospheric air, if the inlet argon flow rate is lowered below 300 sccm. That there is minimal contamination of the APP reactor built here, was verified by conducting an atmospheric pressure PECVD process under acetylene flow, combined with argon flow at 100 sccm and 500 sccm. The deposition of a polymer coating is confirmed by infrared spectroscopy. X-ray photoelectron spectroscopy shows that the polymer coating contains only 5% of oxygen, which is comparable to the oxygen content in polymer deposits obtained in low-pressure PECVD systems.

  14. Fabrication of a Transparent Anti-stain Thin Film Using an Atmospheric Pressure Cold Plasma Deposition System

    Directory of Open Access Journals (Sweden)

    Suzaki Y.

    2013-08-01

    Full Text Available Recently, outdoor-constructed solar panels have a problem such as power generation efficiency is reduced by the face plate dirt. On the other hand, electronic touch panels have a problem such as deterioration of visibility of the screen by finger grease stain. To solve these problems, we need to fabricate the anti-stain surfaces which have superhydrophobic and oil-repellent abilities without spoiling the transparency of the transparent substrate. In this study, we fabricated lotus leaves like surface on a glass substrate. Firstly, SiO2 particles of ca. 100 nm diameter were arranged on the glass substrates. Secondly, to obtain the fractal-like structure (ultra-micro-rough structure on the surface, ZnO thin film having a columnar structure was fabricated on the SiO2 particles by using an atmospheric pressure cold plasma deposition system. By using these processes, the ZnO columns formed radiantly on the spherical surface of the SiO2 particles. Furthermore, without spoiling the ultra-micro-rough structure, a transparent anti-stain monolayer with low surface energy was prepared by using a chemical adsorption technique onto the surface. Average value of the water droplet contact angles of the samples fabricated was 151.8 deg. Field emission scanning electron microscope (FE-SEM observation reviled that this sample has a raspberry structure in which columnar structure has grown radially on the SiO2 particles.

  15. Atmospheric Plasma Depainting

    Science.gov (United States)

    2014-11-19

    Plasma Carbon Dioxide Water Vapor 11 Atmospheric Plasma Depainting, ASETSDefense, Nov 19, 2014 Features and Benefits of APCR Technology Feature...Depainting, ASETSDefense, Nov 19, 2014 14 APC on Aluminum Removal to Primer RAM on Carbon Fiber Partial Topcoat Removal APC Topcoat RAM...60Hz Plasma Flux™ Power Supply VENT To Facility HEPA <= Filtration COTS Six-Axis Robot Aircraft part Particulate Collection System

  16. Deposition of organosilicone thin film from hexamethyldisiloxane (HMDSO) with 50 kHz/33 MHz dual-frequency atmospheric-pressure plasma jet

    Science.gov (United States)

    Jiaojiao, LI; Qianghua, YUAN; Xiaowei, CHANG; Yong, WANG; Guiqin, YIN; Chenzhong, DONG

    2017-04-01

    The deposition of organosilicone thin films from hexamethyldisiloxane(HMDSO) by using a dual-frequency (50 kHz/33 MHz) atmospheric-pressure micro-plasma jet with an admixture of a small volume of HMDSO and Ar was investigated. The topography was measured by using scanning electron microscopy. The chemical bond and composition of these films were analyzed by Fourier transform infrared spectroscopy (FTIR) and x-ray photoelectron spectroscopy. The results indicated that the as-deposited film was constituted by silicon, carbon, and oxygen elements, and FTIR suggested the films are organosilicon with the organic component (–CH x ) and hydroxyl functional group(–OH) connected to the Si–O–Si backbone. Thin-film hardness was recorded by an MH–5–VM Digital Micro-Hardness Tester. Radio frequency power had a strong impact on film hardness and the hardness increased with increasing power.

  17. Assessment of Atmospheric heavy metal deposition in North Egypt aerosols using neutron activation analysis and optical emission inductively coupled plasma

    Energy Technology Data Exchange (ETDEWEB)

    El-Araby, E.H., E-mail: elaraby_20032000@yahoo.com [Faculty of Science, Physics Department, Jezan University, KSA (Saudi Arabia); Abd El-Wahab, M., E-mail: wahab_magda@yahoo.com [Faculty of women for Arts, Science and Education, Physics Department, Ain Shams University, PO11757 Cairo (Egypt); Diab, H.M., E-mail: hnndiab@yahoo.co.uk [National Center of Nuclear Safety and Radiation Control, Atomic Energy Authority Cairo (Egypt); El-Desouky, T.M., E-mail: trkhegazy@yahoo.com [Faculty of women for Arts, Science and Education, Physics Department, Ain Shams University, PO11757 Cairo (Egypt); Mohsen, M., E-mail: m1mohsen@yahoo.com [Faculty of Science. Physics Department, Ain-Shams University, PO 11566 Cairo (Egypt)

    2011-10-15

    The aim of the present study is to assess the current level of atmospheric heavy metal pollution of aerosols in different cities of North Egypt using the neutron activation analysis and optical emission inductively coupled plasma techniques. The results revealed that the highest concentrations of particulate matter PM{sub 10} and total suspended particulate matter were close to industrial areas. From the results of the enrichment factor calculations, the most significant elements of anthropogenic origin are Ba, Sb, Ce and Zn. - Highlights: > Average concentration of Cd using OE-ICP is below detection limit for all the samples. > Maximum average concentration of Pb in PM10 and TSP is 5425 and 570.3, respectively. > Concentration of 20 elements in PM{sub 10} and TSP aerosols are determined using the NAA. > EF revealed that Pb, Ba, Br, Ce, Hf, La Sb and Zn are of anthropogenic origin.

  18. Porous Silicon & Titanium Dioxide Coatings Prepared by Atmospheric Pressure Plasma Jet Chemical Vapour Deposition Technique-A Novel Coating Technology for Photovoltaic Modules

    Directory of Open Access Journals (Sweden)

    S. Bhatt

    2011-01-01

    Full Text Available Atmospheric Pressure Plasma Jet (APPJ is an alternative for wet processes used to make anti reflection coatings and smooth substrate surface for the PV module. It is also an attractive technique because of it’s high growth rate, low power consumption, lower cost and absence of high cost vacuum systems. This work deals with the deposition of silicon oxide from hexamethyldisiloxane (HMDSO thin films and titanium dioxide from tetraisopropyl ortho titanate using an atmospheric pressure plasma jet (APPJ system in open air conditions. A sinusoidal high voltage with a frequency between 19-23 kHz at power up to 1000 W was applied between two tubular electrodes separated by a dielectric material. The jet, characterized by Tg ~ 600-800 K, was mostly laminar (Re ~ 1200 at the nozzle exit and became partially turbulent along the jet axis (Re ~ 3300. The spatially resolved emission spectra showed OH, N2, N2+ and CN molecular bands and O, H, N, Cu and Cr lines as well as the NO2 chemiluminescence continuum (450-800 nm. Thin films with good uniformity on the substrate were obtained at high deposition rate, between 800 -1000 nm.s-1, and AFM results revealed that coatings are relatively smooth (Ra ~ 2 nm. The FTIR and SEM analyses were better used to monitor the chemical composition and the morphology of the films in function of the different experimental conditions.

  19. Ordering of SiOxHyCz islands deposited by atmospheric pressure microwave plasma torch on Si(100) substrates patterned by nanoindentation

    Science.gov (United States)

    Landreau, X.; Lanfant, B.; Merle, T.; Laborde, E.; Dublanche-Tixier, C.; Tristant, P.

    2011-12-01

    SiO x H y C z nanometric layers are deposited from hexamethyldisiloxane by atmospheric pressure microwave plasma torch on Si(100) substrates submitted to temperatures varying on the range [0 °C; 120 °C]. Atomic force microscopy (AFM) characterizations of samples grown at intermediate substrate temperatures (~30 °C) demonstrate a layer-by-layer growth (Frank van der Merwe growth) leading to smooth flat and compact films while films deposited at lower and higher substrates temperatures show an island-like growth (Volmer-Weber growth) generating a high surface roughness. Concomitantly, a detailed infrared spectroscopy analysis of the growing films evidences structural modifications due to changes in the bond types, Si-O-Si conformation and stoichiometry correlated with scanning electron microscopy and AFM characterizations. Then, deposition conditions and specific microstructure are selected with the aim of generating 3-dimensional SiO x H y C z nanostructure arrays on nanoindented Si (100) templates. The first results are discussed.

  20. Structure and deuterium retention properties of tungsten layers deposited by plasma sputtering in a mixed atmosphere of D2 and He

    Science.gov (United States)

    Tang, X. H.; Shi, L. Q.; O'Connor, D. J.; King, B.

    2014-03-01

    The influence of the deposition conditions on the surface morphology, crystal structure and deuterium retention of the tungsten layers formed by rf magnetron plasma sputtering in mixed atmosphere of D2, He and Ar, has been carried out. Helium containing deuterated tungsten layers (named He-WDx) on Cu/Si substrate demonstrate serious film damages with zones of cracks, fractures, flaking-off and large surface blisters. However, these kinds of damages do not happen on the He-WDx layers performed on mechanically polished polycrystalline Cu substrates because of larger surface roughness of the substrates. The crystal structure of the W layer greatly changes with the additional He in the layer, and large amounts of defects resulting in lattice expansion and X-diffraction peak broadening were produced in the W crystal. He in the W layer has direct impacts on D retention. Both D and He concentrations vary simultaneously with He fraction, attached negative bias and substrate temperature.

  1. Energy Deposition Processes in Titan's Upper Atmosphere

    Science.gov (United States)

    Sittler, Edward C., Jr.; Bertucci, Cesar; Coates, Andrew; Cravens, Tom; Dandouras, Iannis; Shemansky, Don

    2008-01-01

    Most of Titan's atmospheric organic and nitrogen chemistry, aerosol formation, and atmospheric loss are driven from external energy sources such as Solar UV, Saturn's magnetosphere, solar wind and galactic cosmic rays. The Solar UV tends to dominate the energy input at lower altitudes of approximately 1100 km but which can extend down to approximately 400 km, while the plasma interaction from Saturn's magnetosphere, Saturn's magnetosheath or solar wind are more important at higher altitudes of approximately 1400 km, but the heavy ion plasma [O(+)] of approximately 2 keV and energetic ions [H(+)] of approximately 30 keV or higher from Saturn's magnetosphere can penetrate below 950km. Cosmic rays with energies of greater than 1 GeV can penetrate much deeper into Titan's atmosphere with most of its energy deposited at approximately 100 km altitude. The haze layer tends to dominate between 100 km and 300 km. The induced magnetic field from Titan's interaction with the external plasma can be very complex and will tend to channel the flow of energy into Titan's upper atmosphere. Cassini observations combined with advanced hybrid simulations of the plasma interaction with Titan's upper atmosphere show significant changes in the character of the interaction with Saturn local time at Titan's orbit where the magnetosphere displays large and systematic changes with local time. The external solar wind can also drive sub-storms within the magnetosphere which can then modify the magnetospheric interaction with Titan. Another important parameter is solar zenith angle (SZA) with respect to the co-rotation direction of the magnetospheric flow. Titan's interaction can contribute to atmospheric loss via pickup ion loss, scavenging of Titan's ionospheric plasma, loss of ionospheric plasma down its induced magnetotail via an ionospheric wind, and non-thermal loss of the atmosphere via heating and sputtering induced by the bombardment of magnetospheric keV ions and electrons. This

  2. Energy Deposition Processes in Titan's Upper Atmosphere

    Science.gov (United States)

    Sittler, Edward C., Jr.; Bertucci, Cesar; Coates, Andrew; Cravens, Tom; Dandouras, Iannis; Shemansky, Don

    2008-01-01

    Most of Titan's atmospheric organic and nitrogen chemistry, aerosol formation, and atmospheric loss are driven from external energy sources such as Solar UV, Saturn's magnetosphere, solar wind and galactic cosmic rays. The Solar UV tends to dominate the energy input at lower altitudes of approximately 1100 km but which can extend down to approximately 400 km, while the plasma interaction from Saturn's magnetosphere, Saturn's magnetosheath or solar wind are more important at higher altitudes of approximately 1400 km, but the heavy ion plasma [O(+)] of approximately 2 keV and energetic ions [H(+)] of approximately 30 keV or higher from Saturn's magnetosphere can penetrate below 950km. Cosmic rays with energies of greater than 1 GeV can penetrate much deeper into Titan's atmosphere with most of its energy deposited at approximately 100 km altitude. The haze layer tends to dominate between 100 km and 300 km. The induced magnetic field from Titan's interaction with the external plasma can be very complex and will tend to channel the flow of energy into Titan's upper atmosphere. Cassini observations combined with advanced hybrid simulations of the plasma interaction with Titan's upper atmosphere show significant changes in the character of the interaction with Saturn local time at Titan's orbit where the magnetosphere displays large and systematic changes with local time. The external solar wind can also drive sub-storms within the magnetosphere which can then modify the magnetospheric interaction with Titan. Another important parameter is solar zenith angle (SZA) with respect to the co-rotation direction of the magnetospheric flow. Titan's interaction can contribute to atmospheric loss via pickup ion loss, scavenging of Titan's ionospheric plasma, loss of ionospheric plasma down its induced magnetotail via an ionospheric wind, and non-thermal loss of the atmosphere via heating and sputtering induced by the bombardment of magnetospheric keV ions and electrons. This

  3. 丝织物的大气压等离子体液相沉积处理%Modification of silk fabric via atmospheric pressure plasma liquid deposition

    Institute of Scientific and Technical Information of China (English)

    蒋晓梅; 陈国强; 芮延年; 刘开强

    2009-01-01

    为提高丝织物表面的拒水、拒油性能,较好地控制沉积涂层的质量,将等离子体与液态沉积液结合,采用介质阻挡放电装置,利用高频高压电源在大气压下通入惰性气体氦(He)产生辉光放电等离子体,通过超声喷嘴将液相单体雾化并喷射入等离子体区域,使之在处理物表面上进行等离子体沉积聚合.应用此工艺对丝织物处理,将全氟庚烷单体经过超声雾化,注人大气压辉光放电区域中,实现了在丝织物表面沉积拒水性涂层.通过SEM观察和ATR-FTIR以及接触角测量,分析处理前后纤维表面形态和结构的变化,得出在不同工艺参数下丝织物表面的全氟庚烷沉积率变化规律.结果表明,纤维表面成功沉积致密膜层,织物表面水接触角增大,拒水性能得到极大的改善.%In order to improve water and oil repellent properties of the silk fabric surface and better control the quality of deposition coating,this paper combines plasma with deposition of liquid.Uniform glow discharge forms at atmospheric pressure with a dielectric barrier discharge (DBD) in helium (He) using high frequency and high voltage power supply.Ultrasonic nozzle atomizes and sprays mist droplets containing liquid monomer directly into the plasma region to complete plasma deposition polymerization on the surface of the substrate.This technology was adopted to treat the silk fabric and ultrasonic atomization of perfluoroheptane monomer was sprayed into an atmospheric pressure glow discharge (APGD) region,leading to the deposition of the hydrophobic film on the silk fabric.The changes of fiber surface morphology and structure were analyzed by using ATR-FTIR,SEM and contact angle measurement.The influences of different processing parameters on change of deposition degree of perfluoroheptane were obtained.After treatment,dense film has been deposited onto fiber surface successfully.Water contact angle and hydrophobicity of the silk fabric

  4. Localised plasma deposition of organosilicon layers on polymer substrates

    NARCIS (Netherlands)

    Theelen, M.J.; Habets, D.; Staemmler, L.; Winands, H.; Bolt, P.J.

    2012-01-01

    Organosilicon coatings provide good optical and mechanical properties and are excellent candidates for the modification of the surface energy of polymers. These coatings can be deposited by plasma polymerization of hexamethyldisiloxane (HMDSO) under atmospheric pressure and at room temperature. The

  5. Photoelectrochemical properties of mesoporous NiO x deposited on technical FTO via nanopowder sintering in conventional and plasma atmospheres.

    Science.gov (United States)

    Awais, Muhammad; Dowling, Denis D; Decker, Franco; Dini, Danilo

    2015-01-01

    Nanoporous nickel oxide (NiO x ) has been deposited with two different procedures of sintering (CS and RDS). Both samples display solid state oxidation at about 3.1 V vs Li+/Li. Upon sensitization of CS/RDS NiO x with erythrosine b (ERY), nickel oxide oxidation occurs at the same potential. Impedance spectroscopy revealed a higher charge transfer resistance for ERY-sensitized RDS NiO x with respect to sensitized CS NiO x . This was due to the chemisorption of a larger amount of ERY on RDS with respect to CS NiO x . Upon illumination the photoinduced charge transfer between ERY layer and NiO x could be observed only with oxidized CS. Photoelectrochemical effects of sensitized RDS NiO x were evidenced upon oxide reduction. With the addition of iodine RDS NiOx electrodes could give the reduction iodine → iodide in addition to the reduction of RDS NiO x . p-type dye sensitized solar cells were assembled with RDS NiO x photocathodes sensitized either by ERY or Fast Green. Resulting overall efficiencies ranged between 0.02 and 0.04 % upon irradiation with solar spectrum simulator (I in: 0.1 W cm(-2)).

  6. Properties of the ZrO2MgO/MgZrO3NiCr/NiCr triple-layer thermal barrier coating deposited by the atmospheric plasma spray process

    OpenAIRE

    Mihailo R. Mrdak

    2016-01-01

    This paper presents the results of the examinations of TBC - ZrO2MgO / MgZrO3NiCr / NiCr thermal barrier layers deposited by the plasma spray process at the atmospheric pressure on substrates of Al alloys. In order to obtain the structural and mechanical properties of layers, which will provide a good heat and abrasion protection of the tail elevators of aircraft J-22 when firing '.Lightning' and 'Thunder' rockets, the deposition of three powder types was performed on 0.6 mm thick Al alloy su...

  7. Heavy metal atmospheric deposition and biomonitoring

    Science.gov (United States)

    Ayrault, S.; Clocchiatti, R.; Carrot, F.; Michel, A.; Gaudry, A.; Moskura, M.

    2003-05-01

    The atmospheric fluxes of heavy metals were measured continuously in the Paris area. The dry depositions were collected on quartz fiber filters, after comparison between clogging capacities and blank levels on commercial filters. Rain was collected in a polyethylene gauge. Two transplanted biomonitors, the epiphytic lichen Evernia prunastri, and the pleurocarpeous moss Scleropodium purum, were exposed simultaneously. These two common biomonitors have been used in previous passive biomonitoring campaigns [Galsomies 1999, Grasso 1999]. This work attempts to produce data on heavy metal exposure of this populated area near Paris, and to compare these two cryptogamic species behaviour. The results on bioaccumulation were compared to those given by a previous work in Italy [Bargagli, 2002] comparing the moss Hypnum cupressiforme and the lichen Parmelia caperata. In our study, the transplanted lichens were exposed in different conditions: to the rain or protected from rain, in vertical, horizontal or oblique position. Dry (filters) and wet (rain) depositions and biomonitors were analysed by Inductively Coupled Plasma-Mass Spectrometry (ICP-MS) and Neutron Activation Analysis (NAA) for more than 30elements [Ayrault, 2001]. The individual particle composition (on filters and cryptogams) was determined by nuclear microprobe (PIXE) and electron microprobe. The lichens displayed different accumulation rates, depending on exposition conditions. In particular, the inclination influenced the bulk concentrations in the lichen. Relation was made between fluxes and concentration accumulated by the biomonitors. The enrichment factors were spectacular for some elements, e.g. lead.

  8. Dielectric properties of Al2O3 coatings deposited via atmospheric plasma spraying and dry-ice blasting correlated with microstructural characteristics

    Science.gov (United States)

    Dong, Shujuan; Song, Bo; Liao, Hanlin; Coddet, Christian

    2015-01-01

    In this work, atmospheric plasma spraying combined with dry-ice blasting have been used to prepare alumina (Al2O3) coatings designed for insulating applications. The microstructural characteristics and dielectric properties of Al2O3 coatings were presented. The electrical insulating properties, i.e., dielectric strength and breakdown voltage, were investigated by dielectric breakdown test using direct current and alternating current. Relationships between dielectric properties and coating characteristics were discussed. The results showed that dry-ice blasting used during atmospheric plasma spray process allowed the production of coatings with better dielectric properties than those prepared without dry-ice blasting. The dielectric properties were correlated with the microstructural characteristics, not with phase composition.

  9. Atmospheric pressure plasma enhanced spatial ALD of silver

    NARCIS (Netherlands)

    Van Den Bruele, F.J.; Smets, M.; Illiberi, A.; Creyghton, Y.; Buskens, P.; Roozeboom, F.; Poodt, P.

    2014-01-01

    The authors have investigated the growth of thin silver films using a unique combination of atmospheric process elements: spatial atomic layer deposition and an atmospheric pressure surface dielectric barrier discharge plasma source. Silver films were grown on top of Si substrates with good purity a

  10. Atmospheric pressure plasma enhanced spatial ALD of silver

    NARCIS (Netherlands)

    Van Den Bruele, F.J.; Smets, M.; Illiberi, A.; Creyghton, Y.; Buskens, P.; Roozeboom, F.; Poodt, P.

    2014-01-01

    The authors have investigated the growth of thin silver films using a unique combination of atmospheric process elements: spatial atomic layer deposition and an atmospheric pressure surface dielectric barrier discharge plasma source. Silver films were grown on top of Si substrates with good purity a

  11. Microwave diagnostics of atmospheric plasmas

    Science.gov (United States)

    Scott, David

    Plasma treatment of biological tissues has tremendous potential due to the wide range of applications. Most plasmas have gas temperatures which greatly exceed room temperature. These are often utilized in electro-surgery for cutting and coagulating tissue. Another type of plasma, referred to as cold atmospheric plasma, or CAP, is characterized by heavy particle temperatures which are at or near room temperature. Due to this lack of thermal effect, CAP may provide less invasive medical procedures. Additionally, CAP have been demonstrated to be effective at targeting cancer cells while minimizing damage to the surrounding tissue. A recently fabricated Microwave Electron Density Device (MEDD) utilizes microwave scattering on small atmospheric plasmas to determine the electron plasma density. The MEDD can be utilized on plasmas which range from a fraction of a millimeter to several centimeters at atmospheric pressure when traditional methods cannot be applied. Microwave interferometry fails due to the small size of the plasma relative to the microwave wavelength which leads to diffraction and negligible phase change; electrostatic probes introduce very strong perturbation and are associated with difficulties of application in strongly-collisional atmospheric conditions; and laser Thomson scattering is not sensitive enough to measure plasma densities less than 1012 cm-3. The first part of this dissertation provides an overview of two types of small atmospheric plasma objects namely CAPs and plasmas utilized in the electro-surgery. It then goes on to describe the fabrication, testing and calibration of the MEDD facility. The second part of this dissertation is focused on the application of the MEDD and other diagnostic techniques to both plasma objects. A series of plasma images that illustrate the temporal evolution of a discharge created by an argon electrosurgical device operating in the coagulation mode and its behavior was analyzed. The discharge of the argon

  12. Plasma polymerization of acrylic acid onto polystyrene by cyclonic plasma at atmospheric pressure

    Science.gov (United States)

    Chang, Yi-Jan; Lin, Chin-Ho; Huang, Chun

    2016-01-01

    The cyclonic atmospheric-pressure plasma is developed for chamberless deposition of poly(acrylic acid) film from argon/acrylic acid mixtures. The photoemission plasma species in atmospheric-pressure plasma polymerization was identified by optical emission spectroscopy (OES). The OES diagnosis data and deposition results indicated that in glow discharge, the CH and C2 species resulted from low-energy electron-impact dissociation that creates deposition species, but the strong CO emission lines are related to nondeposition species. The acrylic acid flow rate is seen as the key factor affecting the film growth. The film surface analysis results indicate that a smooth, continuous, and uniform surface of poly(acrylic acid) films can be formed at a relatively low plasma power input. This study reveals the potential of chamberless film growth at atmospheric pressure for large-area deposition of poly(acrylic acid) films.

  13. Atmospheric deposition 2000. NOVA 2003; Atmosfaerisk deposition 2000. NOVA 2003

    Energy Technology Data Exchange (ETDEWEB)

    Ellermann, T.; Hertel, O.; Hovmand, M.F.; Kemp, K.; Skjoeth, C.A.

    2001-11-01

    This report presents measurements and calculations from the atmospheric part of NOVA 2003 and covers results for 2000. It summarises the main results concerning concentrations and depositions of nitrogen, phosphorus and sulphur compounds related to eutrophication and acidification. Depositions of atmospheric compounds to Danish marine waters as well as land surface are presented. Measurements: In 2000 the monitoring program consisted of eight stations where wet deposition of ammonium, nitrate, phosphate (semi quantitatively) and sulphate were measured using bulk precipitation samplers. Six of the stations had in addition measurements of atmospheric content of A, nitrogen, phosphorus, and sulphur compounds in gas and particulate phase carried out by use of filter pack samplers. Filters were analysed at the National Environmental Research Institute. Furthermore nitrogen dioxide were measured using nitrogen dioxide filter samplers and monitors. Model calculations: The measurements in the monitoring program were supplemented with model calculations of concentrations and depositions of nitrogen and sulphur compounds to Danish land surface, marine waters, fjords and bays using the ACDEP model (Atmospheric Chemistry and Deposition). The model is a so-called trajectory model and simulates the physical and chemical processes in the atmosphere using meteorological and emission data as input. The advantage of combining measurements with model calculations is that the strengths of both methods is obtained. Conclusions concerning: 1) actual concentration levels at the monitoring stations, 2) deposition at the monitoring stations, 3) seasonal variations and 4) long term trends in concentrations and depositions are mainly based on the direct measurements. These are furthermore used to validate the results of the model calculations. Calculations and conclusions concerning: 1) depositions to land surface and to the individual marine water, 2) contributions from different emission

  14. Enhancement of the light-scattering ability of Ga-doped ZnO thin films using SiO{sub x} nano-films prepared by atmospheric pressure plasma deposition system

    Energy Technology Data Exchange (ETDEWEB)

    Chang, Kow-Ming [Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 30010, Taiwan, ROC (China); Ho, Po-Ching, E-mail: raymondsam.ee98g@nctu.edu.tw [Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 30010, Taiwan, ROC (China); Ariyarit, Atthaporn [Department of Electronics Engineering and Institute of Electronics, National Chiao Tung University, 1001 Ta Hsueh Road, Hsinchu 30010, Taiwan, ROC (China); Yang, Kuo-Hui; Hsu, Jui-Mei; Wu, Chin-Jyi; Chang, Chia-Chiang [Industrial Technology Research Institute, Mechanical and Systems Research Laboratories, Hsinchu 31040, Taiwan, ROC (China)

    2013-12-02

    To enhance the light-trapping qualities of silicon thin-film solar cells, the use of transparent conductive oxide with high haze and high conductivity is essential. This study investigated an eco-friendly technique that used bilayer Ga-doped zinc oxide/SiO{sub x} films prepared with an atmospheric pressure plasma jet to achieve high haze and low resistivity. A minimum resistivity of 6.00 × 10{sup −4} Ω·cm was achieved at 8 at.% gallium doping. Examination of X-ray diffraction spectra showed that increased film thickness led to increased carrier concentration in GZO bilayers. The optimal bilayer GZO film achieved considerably higher haze values in the visible and NIR regions, compared with Asahi U-type fluorine doped tin oxide. - Highlights: • Ga-doped ZnO (GZO) and SiO{sub x} deposited by atmospheric pressure plasma jet (APPJ) • Deposition uses a water-based precursor and low substrate temperature (< 150 °C). • SiO{sub x} buffer layers deposited by APPJ can control haze value of Ga-doped ZnO films. • GZO/SiO{sub x} achieved the resistivity of 6.00 × 10{sup −4} Ω·cm and haze of 21.5% at 550 nm.

  15. Atmospheric pressure plasma jet applications

    Energy Technology Data Exchange (ETDEWEB)

    Park, J.; Herrmann, H.W.; Henins, I.; Selwyn, G.S. [Los Alamos National Lab., NM (United States)

    1998-12-31

    The atmospheric pressure plasma jet (APPJ) is a non-thermal, high pressure plasma discharge that produces a high velocity effluent stream of highly reactive chemical species. The discharge operates on a feedstock gas (e.g., He/O2/H2O) which flows between two concentric cylindrical electrodes: an outer grounded electrode and an inner electrode powered at 13.56 MHz RF. While passing through the plasma, the feedgas becomes excited, ionized or dissociated by electron impact. The fast-flowing effluent consists of ions and electrons, which are rapidly lost by recombination, highly reactive radicals (e.g., O, OH), and metastable species (e.g., O2). The metastable O2, which is reactive to hydrocarbon and other organic species, has been observed through optical emission spectroscopy to decrease by a factor of 2 from the APPJ nozzle exit to a distance of 10 cm. Unreacted metastable O2, and that which does not impinge on a surface, will then decay back to ordinary ground state O2, resulting in a completely dry, environmentally-benign form of surface cleaning. Applications such as removal of photoresist, oxide films and organic residues from wafers for the electronics industry, decontamination of civilian and military areas and personnel exposed to chemical or biological warfare agents, and paint (e.g., graffiti) removal are being considered.

  16. Fluorocarbon coatings deposited on micron-sized particles by atmospheric PECVD

    NARCIS (Netherlands)

    Abadjieva, E.; Heijden, A.E.D.M. van der; Creyghton, Y.L.M.; Ommen, J.R. van

    2012-01-01

    Fluorocarbon coatings have been deposited on micron-sized silica particles by means of atmospheric pressure plasma-enhanced chemical vapor deposition (PECVD). The silica particles have a diameter in the range between 40 and 70 ?m. They are fluidized at atmospheric pressure in a circulating fluidized

  17. Plasma-deposited a-C(N) H films

    CERN Document Server

    Franceschini, D E

    2000-01-01

    The growth behaviour, film structure and mechanical properties of plasma-deposited amorphous hydrogenated carbon-nitrogen films are shortly reviewed. The effect of nitrogen-containing gas addition to the deposition to the hydrocarbon atmospheres used is discussed, considering the modifications observed in the chemical composition growth kinetics, carbon atom hybridisation and chemical bonding arrangements of a-C(N):H films. The overall structure behaviour is correlated to the variation of the mechanical properties.

  18. Hard Carbon Films Deposited under Various Atmospheres

    Science.gov (United States)

    Wei, M.-K.; Chen, S.-C.; Wu, T. C.; Lee, Sanboh

    1998-03-01

    Using a carbon target ablated with an XeCl-excimer laser under various gas atmospheres at different pressures, hard carbon was deposited on silicon, iron and tungsten carbide substrates. The hardness, friction coefficient, and wear rate of the film against steel are better than pure substrate material, respectively, so that it has potential to be used as a protective coating for micromechanical elements. The influences of gas pressure, gas atmosphere, and power density of laser irradiation on the thermal stability of film were analyzed by means of Raman-spectroscope, time-of-flight method, and optical emission spectrum. It was found that the film deposited under higher pressure has less diamond-like character. The film deposited under rest gas or argon atmosphere was very unstable and looked like a little graphite-like character. The film deposited at high vacuum (10-5 mbar rest gas) was the most stable and looked like the most diamond-like character. The film deposited at higher power density was more diamond-like than that at lower power density.

  19. Atmospheric deposition of organic carbon via precipitation

    Science.gov (United States)

    Iavorivska, Lidiia; Boyer, Elizabeth W.; DeWalle, David R.

    2016-12-01

    Atmospheric deposition is the major pathway for removal of organic carbon (OC) from the atmosphere, affecting both atmospheric and landscape processes. Transfers of OC from the atmosphere to land occur as wet deposition (via precipitation) and as dry deposition (via surface settling of particles and gases). Despite current understanding of the significance of organic carbon inputs with precipitation to carbon budgets, transfers of organic matter between the atmosphere and land are not explicitly included in most carbon cycle models due to limited data, highlighting the need for further information. Studies regarding the abundance of OC in precipitation are relatively sparse, in part due to the fact that concentrations of organics in precipitation and their associated rates of atmospheric deposition are not routinely measured as a part of major deposition monitoring networks. Here, we provide a new data synthesis from 83 contemporary studies published in the peer reviewed literature where organic matter in precipitation was measured around the world. We compiled data regarding the concentrations of organic carbon in precipitation and associated rates of atmospheric deposition of organic carbon. We calculated summary statistics in a common set of units, providing insights into the magnitude and regional variability of OC in precipitation. A land to ocean gradient is evident in OC concentrations, with marine sites generally showing lower values than continental sites. Our synthesis highlights gaps in the data and challenges for data intercomparison. There is a need to concentrate sampling efforts in areas where anthropogenic OC emissions are on the rise (Asia, South America), as well as in remote sites suggesting background conditions, especially in Southern Hemisphere. It is also important to acquire more data for marine rainwater at various distances from the coast in order to assess a magnitude of carbon transfer between the land and the ocean. Our integration of

  20. Atmospheric pressure plasma for surface modification

    CERN Document Server

    Wolf, Rory A

    2012-01-01

    This Book's focus and intent is to impart an understanding of the practical application of atmospheric plasma for the advancement of a wide range of current and emerging technologies. The primary key feature of this book is the introduction of over thirteen years of practical experimental evidence of successful surface modifications by atmospheric plasma methods. It offers a handbook-based approach for leveraging and optimizing atmospheric plasma technologies which are currently in commercial use. It also offers a complete treatment of both basic plasma physics and industrial plasma process

  1. Plasma-ion Induced Sputtering and Heating of Titan's Atmosphere

    Science.gov (United States)

    Johnson, R. E.; Tucker, O. J.

    2007-05-01

    Titan is unique among the outer solar system icy satellites in having an atmosphere with a column density about ten times that of the Earth's atmosphere and an atmospheric mass to solid mass ratio comparable to that of Venus. Atmospheres equivalent in size to that at Titan would have been removed from the icy Galilean satellites by the plasma trapped in the Jovian magnetosphere (Johnson 2004). Therefore, the use of Cassini data to determine the present erosion rate of Titan's atmosphere provides an important end point for studying the erosion and heating of planetary and satellite atmospheres by an ambient plasma. In this paper we describe the deposition of energy, the erosion and the expansion of the upper atmosphere of Titan using Direct Simulation Monte Carlo models (Shematovich et al. 2003; Michael et al. 2005; Michael and Johnson 2005). These calculations are used to calibrate semi-empirical models of atmospheric sputtering (Johnson 1994) that are used to interpret Cassini data at Titan. Using a number of plasma conditions, the temperature and density vs. altitude above the exobase and the rate of escape are calculated. References: Johnson, R.E. "Plasma-induced Sputtering of an Atmosphere" in Space Science Reviews 69 215-253 (1994). Johnson. R.E., " The magnetospheric plasmadriven evolution of satellite atmospheres" Astrophys. J. 609, L99-L102 (2004). Michael, M. and R.E. Johnson, "Energy deposition of pickup ions and heating of Titan's atmosphere", Planetary & Space Sci.53, 1510-1514 (2005). Michael M., R.E. Johnson, F. Leblanc, M. Liu, J.G. Luhmann, and V.I. Shematovich, "Ejection of nitrogen from Titan's atmosphere by magnetospheric ions and pick-up ions", Icarus 175, 263-267 (2005). Shematovich, V.I., R.E. Johnson, M. Michael, and J.G. Luhmann, "Nitrogen loss from Titan", JGR 108, No. E8, 5087, doi:10.1029/2003JE002094 (2003).

  2. MEAD Marine Effects of Atmospheric Deposition

    Science.gov (United States)

    Jickells, T.; Spokes, L.

    2003-04-01

    The coastal seas are one of the most valuable resources on the planet but they are threatened by human activity. We rely on the coastal area for mineral resources, waste disposal, fisheries and recreation. In Europe, high population densities and high levels of industrial activity mean that the pressures arising from these activities are particularly acute. One of the main problems concerning coastal seas is the rapid increase in the amounts of nitrogen-based pollutants entering the water. They come from many sources, the most important ones being traffic, industry and agriculture. These pollutants can be used by algae as nutrients. The increasing concentrations of these nutrients have led to excessive growth of algae, some of which are harmful. When algae die and decay, oxygen in the water is used up and the resulting lower levels of oxygen may lead to fish kills. Human activity has probably doubled the amount of chemically and biologically reactive nitrogen present globally. In Europe the increases have been greater than this, leading to real concern over the health of coastal waters. Rivers have, until recently, been thought to be the most important source of reactive nitrogen to the coastal seas but we now know that inputs from the atmosphere are large and can equal, or exceed, those from the rivers. Our initial hypothesis was that atmospheric inputs are important and potentially different in their effect on coastal ecosystems to riverine inputs and hence require different management strategies. However, we had almost no information on the direct effects of atmospheric deposition on marine ecosystems, though clearly such a large external nitrogen input should lead to enhanced phytoplankton growth The aim of this European Union funded MEAD project has been to determine how inputs of nitrogen from the atmosphere affect the chemistry and biology of coastal waters. To try to answer this, we have conducted field experiments in the Kattegat, an area where we know

  3. Polymerization of acrylic acid using atmospheric pressure DBD plasma jet

    Science.gov (United States)

    Bashir, M.; Bashir, S.

    2016-08-01

    In this paper polymerization of acrylic acid was performed using non thermal atmospheric pressure plasma jet technology. The goal of this study is to deposit organic functional coatings for biomedical applications using a low cost and rapid growth rate plasma jet technique. The monomer solution of acrylic acid was vaporized and then fed into the argon plasma for coating. The discharge was powered using a laboratory made power supply operating with sinusoidal voltage signals at a frequency of 10 kHz. The optical emission spectra were collected in order to get insight into the plasma chemistry during deposition process. The coatings were characterized using Fourier transform infrared spectroscopy, atomic force microscopy and growth rates analysis. A high retention of carboxylic functional groups of the monomer was observed at the surface deposited using this low power technique.

  4. Atmospheric Pressure Plasma Process And Applications

    Energy Technology Data Exchange (ETDEWEB)

    Peter C. Kong; Myrtle

    2006-09-01

    This paper provides a general discussion of atmospheric-pressure plasma generation, processes, and applications. There are two distinct categories of atmospheric-pressure plasmas: thermal and nonthermal. Thermal atmospheric-pressure plasmas include those produced in high intensity arcs, plasma torches, or in high intensity, high frequency discharges. Although nonthermal plasmas are at room temperatures, they are extremely effective in producing activated species, e.g., free radicals and excited state atoms. Thus, both thermal and nonthermal atmosphericpressure plasmas are finding applications in a wide variety of industrial processes, e.g. waste destruction, material recovery, extractive metallurgy, powder synthesis, and energy conversion. A brief discussion of recent plasma technology research and development activities at the Idaho National Laboratory is included.

  5. Non-equilibrium,Atmospheric-pressure Plasma Jet for Depositing Silicon Oxide Films%大气压非平衡等离子体沉积氧化硅薄膜

    Institute of Scientific and Technical Information of China (English)

    林江; 张溪文; 韩高荣

    2012-01-01

    本文搭建了一套大气压等离子体薄膜沉积系统,其装置采用喷枪方式,结合运动机构控制喷枪按特定轨迹移动镀膜。四乙氧基硅烷(TEOS)作为硅的先驱体,氮气为先驱体载气和等离子体放电气体,基底温度50℃~300℃,进行了大气压等离子体化学气相沉积氧化硅薄膜的研究。运用红外光谱(FTIR)、光学椭偏仪,扫描电镜(SEM)和纳米压痕仪对沉积的薄膜进行了表征。研究表明,薄膜中富含Si—O—Si键且有少量S—OH键;较高基底温度有利于在硅基底上得到一层平整致密的薄膜;基底温度300℃时薄膜硬度达到4.8GPa,略低于采用PECVD方法沉积的氧化硅薄膜。%A non-equilibrium atmospheric-pressure plasma jet was developed.A kinetic controlling system was integrated to control the movement of plasma jet,which was used to deposit silicon oxide films.TEOS was used as the precursor.N2 gas was used to generate plasma and carry precursor.Substrate temperature was varied from 50℃ to 300℃.As-deposited films were characterized by ellipsometrry,Fourier transform infrared(FTIR) spectroscopy,scanning electron microscopy(SEM) and nano-indentometry.FTIR spectra indicate that there are a majority of Si-O-Si bonds and a minority of Si-OH bonds in the as-deposited films.Higher substrate temperature is contributive to depositing flat and compact films.Under substrate temperature 300℃,film hardness is up to 4.8GPa,which is slightly less than that of films deposited by plasma enhanced chemical vapor deposition(PECVD).

  6. Electrode Configurations in Atmospheric Pressure Plasma Jets

    Science.gov (United States)

    Lietz, Amanda M.; Kushner, Mark J.

    2016-09-01

    Atmospheric pressure plasma jets (APPJs) are being studied for emerging medical applications including cancer treatment and wound healing. APPJs typically consist of a dielectric tube through which a rare gas flows, sometimes with an O2 or H2O impurity. In this paper, we present results from a computational study of APPJs using nonPDPSIM, a 2-D plasma hydrodynamics model, with the goal of providing insights on how the placement of electrodes can influence the production of reactive species. Gas consisting of He/O2 = 99.5/0.5 is flowed through a capillary tube at 2 slpm into humid air, and a pulsed DC voltage is applied. An APPJ with two external ring electrodes will be compared with one having a powered electrode inside and a ground electrode on the outside. The consequences on ionization wave propagation and the production of reactive oxygen and nitrogen species (RONS) will be discussed. Changing the electrode configuration can concentrate the power deposition in volumes having different gas composition, resulting in different RONS production. An internal electrode can result in increased production of NOx and HNOx by increasing propagation of the ionization wave through the He dominated plume to outside of the tube where humid air is diffusing into the plume. Work supported by US DOE Office of Fusion Energy Science and the National Science Foundation.

  7. Monitoring particle growth in deposition plasmas

    Science.gov (United States)

    Schlebrowski, T.; Bahre, H.; Böke, M.; Winter, J.

    2013-12-01

    Plasma-enhanced chemical vapor deposition methods are frequently used to deposit barrier layers, e.g. on polymers for food packaging. These plasmas may suffer from particle (dust) formation. We report on a flexible monitoring system for dust. It is based on scanning a 3D plasma volume for particles by laser light scattering. The lower size limit of particles detected in the presented system is 20 nm. We report on existence diagrams for obtaining dust free or dust loaded capacitively or inductively coupled rf-plasmas in C2H2 depending on pressure, flow and rf-power. We further present growth rates for dust in these plasmas and show that monodisperse particles are only obtained during the first growth cycle.

  8. Ecological effects of atmospheric nitrogen deposition on soil enzyme activity

    Institute of Scientific and Technical Information of China (English)

    WANG Cong-yan; Lv Yan-na; LIU Xue-yan Liu; WANG Lei

    2013-01-01

    The continuing increase in human activities is causing global changes such as increased deposition of atmospheric nitrogen.There is considerable interest in understanding the effects of increasing atmospheric nitrogen deposition on soil enzyme activities,specifically in terms of global nitrogen cycling and its potential future contribution to global climate change.This paper summarizes the ecological effects of atmospheric nitrogen deposition on soil enzyme activities,including size-effects,stage-effects,site-effects,and the effects of different levels and forms of atmospheric nitrogen deposition.We discuss needs for further research on the relationship between atmospheric nitrogen deposition and soil enzymes.

  9. Plasma distribution of cathodic ARC deposition system

    Energy Technology Data Exchange (ETDEWEB)

    Anders, S.; Raoux, S.; Krishnan, K.; MacGill, R.A.; Brown, I.G. [Lawrence Berkeley National Lab., CA (United States)

    1996-08-01

    The plasma distribution using a cathodic arc plasma source with and without magnetic macroparticle filter has been determined by depositing on a transparent plastic substrate and measuring the film absorption. It was found that the width of the distribution depends on the arc current, and it also depends on the cathode material which leads to a spatial separation of the elements when an alloy cathode is used. By applying a magnetic multicusp field near the exit of the magnetic filter, it was possible to modify the plasma distribution and obtain a flat plasma profile with a constant and homogeneous elemental distribution.

  10. Atmospheric plasma processes for environmental applications

    OpenAIRE

    Shapoval, Volodymyr

    2012-01-01

    Plasma chemistry is a rapidly growing field which covers applications ranging from technological processing of materials, including biological tissues, to environmental remediation and energy production. The so called atmospheric plasma, produced by electric corona or dielectric barrier discharges in a gas at atmospheric pressure, is particularly attractive for the low costs and ease of operation and maintenance involved. The high concentrations of energetic and chemically active species (e.g...

  11. Atmospheric plasma processes for environmental applications

    OpenAIRE

    Shapoval, Volodymyr

    2012-01-01

    Plasma chemistry is a rapidly growing field which covers applications ranging from technological processing of materials, including biological tissues, to environmental remediation and energy production. The so called atmospheric plasma, produced by electric corona or dielectric barrier discharges in a gas at atmospheric pressure, is particularly attractive for the low costs and ease of operation and maintenance involved. The high concentrations of energetic and chemically active species (e.g...

  12. Nanocapillary Atmospheric Pressure Plasma Jet: A Tool for Ultrafine Maskless Surface Modification at Atmospheric Pressure.

    Science.gov (United States)

    Motrescu, Iuliana; Nagatsu, Masaaki

    2016-05-18

    With respect to microsized surface functionalization techniques we proposed the use of a maskless, versatile, simple tool, represented by a nano- or microcapillary atmospheric pressure plasma jet for producing microsized controlled etching, chemical vapor deposition, and chemical modification patterns on polymeric surfaces. In this work we show the possibility of size-controlled surface amination, and we discuss it as a function of different processing parameters. Moreover, we prove the successful connection of labeled sugar chains on the functionalized microscale patterns, indicating the possibility to use ultrafine capillary atmospheric pressure plasma jets as versatile tools for biosensing, tissue engineering, and related biomedical applications.

  13. Atmospheric mass deposition by captured planetesimals

    Science.gov (United States)

    Iaroslavitz, Eyal; Podolak, Morris

    2007-04-01

    We examine the deposition of heavy elements in the envelope of a protoplanet growing according to the core accretion scenario of Pollack et al. [Pollack, J.B., Hubickyj, O., Bodenheimer, P., Lissauer, J.J., Podolak, M., Greenzweig, Y., 1996. Icarus 124, 62-85]. We use their atmospheric models and the deposition rates that they computed, and we calculate the amount of heavy elements that can be dissolved in the envelope. For planetesimals composed of a mixture of water, CHON, and rock, we find that almost all of the water is dissolved in the atmosphere. A substantial amount of CHON is also dissolved but it remains sequestered at high temperatures near the core. Some fraction of the rock is also dissolved in the very high temperature region near the core envelope boundary. If this dissolved material can be mixed upward later in the planet's evolution, the resulting structure would be much closer to that determined by matching the moments of Jupiter's gravitational field.

  14. Geophysical Plasmas and Atmospheric Modeling.

    Science.gov (United States)

    1982-01-01

    will be submitted to the Journal of the Atmospheric Sciences. 32 - .- I. LIMITATIONS ON STRATOSPHERIC DYNAMICS We have performed an investigation of...Amplitudes" which will be submitted to the Journal of the Atmospheric Sciences. 1i 33 A& J. GENERAL CIRCULATION MODEL STUDIES Comparison computer runs...In tis case, as clearly shov.i by Petvia-mensona. I ths cseas ceary sou byPetia- cavities requires a local theory going beyond the limitshvilli,’ the

  15. Local plasma deposition on polymer components

    NARCIS (Netherlands)

    Bolt, P.J.; Theelen, M.J.; Habets, D.; Winands, G.J.J.; Staemmler, L.

    2011-01-01

    For the modification of the surface energy of polymers, organosilicon coatings provide good optical and mechanical properties and are excellent candidates for the modification of the surface energy of polymers. These coatings can be deposited by plasma polymerization of hexamethyldisiloxane (HMDSO)

  16. Plasma Processes : Microwave plasma deposition of diamond like carbon coatings

    Indian Academy of Sciences (India)

    D S Patil; K Ramachandran; N Venkatramani; M Pandey; R D'Cunha

    2000-11-01

    The promising applications of the microwave plasmas have been appearing in the fields of chemical processes and semiconductor manufacturing. Applications include surface deposition of all types including diamond/diamond like carbon (DLC) coatings, etching of semiconductors, promotion of organic reactions, etching of polymers to improve bonding of the other materials etc. With a 2.45 GHz, 700 W, microwave induced plasma chemical vapor deposition (CVD) system set up in our laboratory we have deposited diamond like carbon coatings. The microwave plasma generation was effected using a wave guide single mode applicator. We have deposited DLC coatings on the substrates like stainless steel, Cu–Be, Cu and Si. The deposited coatings have been characterized by FTIR, Raman spectroscopy and ellipsometric techniques. The results show that we have achieved depositing ∼ 95% sp3 bonded carbon in the films. The films are uniform with golden yellow color. The films are found to be excellent insulators. The ellipsometric measurements of optical constant on silicon substrates indicate that the films are transparent above 900 nm.

  17. Possibilities of plasma decontamination at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, Masaaki; Windarto, Hendri; Matsumoto, Takeshi; Akatsuka, Hiroshi [Tokyo Institute of Technology, Tokyo (Japan); Sakagishi, Kohji [ATOX Co., Ltd., Chiba (Japan)

    1999-07-01

    The highly effective decontamination process by using atmospheric pressure plasma is proposed. The microwave plasma generator, which we designed, is suitable for discharge of molecular gas and it has a special feature as a source of high concentration reactive atoms in the discharge o molecular gases rather than a plasma source. To demonstrate this idea and discuss about its possibility, some cold experiments were carried out. Our experimental results shows the high effectiveness and it can be concluded consequently that the proposed process has the possibility of the practical processing with having the advantage of plasma decontamination technique which have been investigated under the low pressure conditions. (author)

  18. Diagnostics in ? helicon plasmas for ? deposition

    Science.gov (United States)

    Granier, A.; Nicolazo, F.; Vallée, C.; Goullet, A.; Turban, G.; Grolleau, B.

    1997-05-01

    0963-0252/6/2/008/img3 and 0963-0252/6/2/008/img4 helicon plasmas used for plasma enhanced chemical vapour deposition of 0963-0252/6/2/008/img5 films are investigated in the 1 - 10 mTorr pressure and 0 - 800 W rf power ranges. The positive oxygen ions are analysed by energy selective mass spectrometry and Langmuir probes. The oxygen atom concentration is monitored by actinometry and ionization threshold mass spectrometry. In oxygen plasmas it is shown that 0963-0252/6/2/008/img6 is the major positive ion, and that the oxygen molecules are far from being completely dissociated, due to a very high oxygen atom recombination frequency on the reactor walls. The dissociation degree increases with the rf power reaching 10% at 500 W. In 0963-0252/6/2/008/img4 plasmas, the plasma density and electron temperature decrease as the TEOS fraction increases. In contrast, the degree of oxygen dissociation increases sharply with the addition of a few per cent TEOS, is maximum for about 5% TEOS and decreases as TEOS fraction is further increased. In a 95:5 0963-0252/6/2/008/img4 plasma (5 mTorr, 300 W) the fluxes of oxygen positive ions and atoms impinging onto a floating substrate are estimated to be 0963-0252/6/2/008/img9 and 0963-0252/6/2/008/img10 respectively. Under these plasma conditions, near-stoichiometric 0963-0252/6/2/008/img11 films, with low OH content, are deposited at ambient temperature. The corresponding atom to ion flux ratio is about 250, which suggests the dominant role of oxygen atoms in the deposition kinetics. The comparison of the compositions of layers grown in a 5 mTorr 95:5 0963-0252/6/2/008/img4 plasma at two rf powers confirms the major role of oxygen atoms.

  19. Atmospheric Gaseous Plasma with Large Dimensions

    Science.gov (United States)

    Korenev, Sergey

    2012-10-01

    The forming of atmospheric plasma with large dimensions using electrical discharge typically uses the Dielectric Barrier Discharge (DBD). The study of atmospheric DBD was shown some problems related to homogeneous volume plasma. The volume of this plasma determines by cross section and gas gap between electrode and dielectric. The using of electron beam for volume ionization of air molecules by CW relativistic electron beams was shown the high efficiency of this process [1, 2]. The main advantage of this approach consists in the ionization of gas molecules by electrons in longitudinal direction determines by their kinetic energy. A novel method for forming of atmospheric homogeneous plasma with large volume dimensions using ionization of gas molecules by pulsed non-relativistic electron beams is presented in the paper. The results of computer modeling for delivered doses of electron beams in gases and ionization are discussed. The structure of experimental bench with plasma diagnostics is considered. The preliminary results of forming atmospheric plasma with ionization gas molecules by pulsed nanosecond non-relativistic electron beam are given. The analysis of potential applications for atmospheric volume plasma is presented. Reference: [1] S. Korenev. ``The ionization of air by scanning relativistic high power CW electron beam,'' 2002 IEEE International Conference on Plasma Science. May 2002, Alberta, Canada. [2] S. Korenev, I. Korenev. ``The propagation of high power CW scanning electron beam in air.'' BEAMS 2002: 14th International Conference on High-Power Particle Beams, Albuquerque, New Mexico (USA), June 2002, AIP Conference Proceedings Vol. 650(1), pp. 373-376. December 17.

  20. Plasma deposited fluorinated films on porous membranes

    Energy Technology Data Exchange (ETDEWEB)

    Gancarz, Irena [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Bryjak, Marek, E-mail: marek.bryjak@pwr.edu.pl [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Kujawski, Jan; Wolska, Joanna [Department of Polymer and Carbon Materials, Wrocław University of Technology, 50-370 Wrocław (Poland); Kujawa, Joanna; Kujawski, Wojciech [Nicolaus Copernicus University, Faculty of Chemistry, 7 Gagarina St., 87-100 Torun (Poland)

    2015-02-01

    75 KHz plasma was used to modify track etched poly(ethylene terephthalate) membranes and deposit on them flouropolymers. Two fluorine bearing monomers were used: perflourohexane and hexafluorobenzene. The modified surfaces were analyzed by means of attenuated total reflection infra-red spectroscopy, X-ray photoelectron spectroscopy, scanning electron microscopy, atomic force microscopy and wettability. It was detected that hexaflourobenxene deposited to the larger extent than perflourohaxane did. The roughness of surfaces decreased when more fluoropolymer was deposited. The hydrophobic character of surface slightly disappeared during 20-days storage of hexaflourobenzene modified membrane. Perfluorohexane modified membrane did not change its character within 120 days after modification. It was expected that this phenomenon resulted from post-reactions of oxygen with radicals in polymer deposits. The obtained membranes could be used for membrane distillation of juices. - Highlights: • Plasma deposited hydrophobic layer of flouropolymers. • Deposition degree affects the surface properties. • Hydrohilization of surface due to reaction of oxygen with entrapped radicals. • Possibility to use modified porous membrane for water distillation and apple juice concentration.

  1. Plasma transferred arc deposition of beryllium

    Science.gov (United States)

    Hollis, K.; Bartram, B.; Withers, J.; Storm, R.; Massarello, J.

    2006-12-01

    The exceptional properties of beryllium (Be), including low density and high elastic modulus, make it the material of choice in many defense and aerospace applications. However, health hazards associated with Be material handling limit the applications that are suited for its use. Innovative solutions that enable continued use of Be in critical applications while addressing worker health concerns are highly desirable. Plasma transferred arc solid free-form fabrication is being evaluated as a Be fabrication technique for civilian and military space-based components. Initial experiments producing Be deposits are reported here. Deposit shape, microstructure, and mechanical properties are reported.

  2. Formation Mechanism of Atmospheric Pressure Plasma Jet

    CERN Document Server

    Jiang, Nan; Cao, Zexian

    2008-01-01

    Atmospheric pressure plasma jet can protrude some 5.0 cm into air. It holds promise for multivarious innovative applications, but its formation mechanism remains unsettled. We show that the plasma jet is essentially a streamer corona totally independent of, but obscured by, dielectric barrier discharge. Consequently, the jets can be equally successfully generated even with one single bare metal electrode attached to the tube orifice, both downstream and upstream simultaneously, and at a significantly reduced voltage. These results will help understand the underlying physics and facilitate a safer and more flexible implementation of this marvelous plasma source.

  3. Hot Corrosion Performance of AlO-CrO/NiCoCrAlYTa and AlO/NiCoCrAlYTa Coatings Deposited by Atmospheric Plasma Spraying

    Science.gov (United States)

    Tao, Chong; Wang, Lei; Cheng, Nailiang; Hu, Hengfa; Liu, Yang; Song, Xiu

    2016-04-01

    AlO-CrO/NiCoCrAlYTa and AlO/NiCoCrAlYTa coatings were deposited on 316L stainless steel substrate using atmospheric plasma spraying, respectively, in order to improve the oxidation and corrosion resistance. The hot corrosion performance of the coatings at 700 and 900 °C were studied, and the detailed microstructures and phase composition of the coatings were analyzed using x-ray diffraction, scanning electron microscope with energy dispersive spectrometer, and transmission electron microscope. The results show that both coatings are structurally featured by slatted layers, consisting of amorphous phase, Cr2O3, Ni3Al, and Al2O3. The hot corrosion resistance of AlO-CrO/NiCoCrAlYTa coating is better than that of AlO/NiCoCrAlYTa coating. This improvement is attributed to lower porosity and more compact Cr2O3 in AlO-CrO/NiCoCrAlYTa coating which performs better than Al2O3 in blocking further inward progress of corrosion and oxidization.

  4. A record of atmospheric Pb-210 deposition in The Netherlands

    NARCIS (Netherlands)

    Beks, J.P.; Eisma, D.; Van Der Plicht, J.

    1998-01-01

    The deposition flux of total atmospheric 210Pb has been measured at two sites in The Netherlands: Texel from 1992 to 1996 and Groningen from 1989 to 1994. With predominant westerly oceanic winds, the annual 210Pb deposition is relatively low as 222Rn, the source for atmospheric 210Pb, is mainly exha

  5. Cold Atmosphere Plasma in Cancer Therapy

    Science.gov (United States)

    Keidar, Michael

    2012-10-01

    Plasma is an ionized gas that is typically generated in high-temperature laboratory conditions. Recent progress in atmospheric plasmas led to the creation of cold plasmas with ion temperature close to room temperature. Areas of potential application of cold atmospheric plasmas (CAP) include dentistry, drug delivery, dermatology, cosmetics, wound healing, cellular modifications, and cancer treatment. Various diagnostic tools have been developed for characterization of CAP including intensified charge-coupled device cameras, optical emission spectroscopy and electrical measurements of the discharge propertied. Recently a new method for temporally resolved measurements of absolute values of plasma density in the plasma column of small-size atmospheric plasma jet utilizing Rayleigh microwave scattering was proposed [1,2]. In this talk we overview state of the art of CAP diagnostics and understanding of the mechanism of plasma action of biological objects. The efficacy of cold plasma in a pre-clinical model of various cancer types (long, bladder, and skin) was recently demonstrated [3]. Both in-vitro and in-vivo studies revealed that cold plasmas selectively kill cancer cells. We showed that: (a) cold plasma application selectively eradicates cancer cells in vitro without damaging normal cells. For instance a strong selective effect was observed; the resulting 60--70% of lung cancer cells were detached from the plate in the zone treated with plasma, whereas no detachment was observed in the treated zone for the normal lung cells under the same treatment conditions. (b) Significantly reduced tumor size in vivo. Cold plasma treatment led to tumor ablation with neighbouring tumors unaffected. These experiments were performed on more than 10 mice with the same outcome. We found that tumors of about 5mm in diameter were ablated after 2 min of single time plasma treatment. The two best known cold plasma effects, plasma-induced apoptosis and the decrease of cell migration

  6. Atmospheric pressure plasma enhanced spatial ALD of silver

    Energy Technology Data Exchange (ETDEWEB)

    Bruele, Fieke J. van den, E-mail: Fieke.vandenBruele@tno.nl; Smets, Mireille; Illiberi, Andrea; Poodt, Paul [Holst Centre/TNO, High Tech Campus 31, 5656 AE Eindhoven (Netherlands); Creyghton, Yves [TNO, High Tech Campus 21, 5656 AE Eindhoven (Netherlands); Buskens, Pascal [TNO, Rondom 1, 5612 AP Eindhoven, The Netherlands and DWI Leibniz-Institut für Interaktive Materialien, Aachen (Germany); Roozeboom, Fred [TNO, High Tech Campus 21, 5656 AE Eindhoven, The Netherlands and Department of Applied Physics, Eindhoven University of Technology, 5600 MB Eindhoven (Netherlands)

    2015-01-15

    The authors have investigated the growth of thin silver films using a unique combination of atmospheric process elements: spatial atomic layer deposition and an atmospheric pressure surface dielectric barrier discharge plasma source. Silver films were grown on top of Si substrates with good purity as revealed by resistivity values as low as 18 μΩ cm and C- and F-levels below detection limits of energy dispersive x-ray analysis. The growth of the silver films starts through the nucleation of islands that subsequently coalesce. The authors show that the surface island morphology is dependent on surface diffusion, which can be controlled by temperature within the deposition temperature range of 100–120 °C.

  7. Atmospheric iron deposition: global distribution, variability, and human perturbations

    OpenAIRE

    N. Mahowald; S. Engelstaedter; Luo, C; Sealy, A.; Artaxo, P.; Benitez-Nelson, C.R.; Bonnet, S.; Chen, Y.; Chuang, P. Y.; Cohen, D.; Dulac, F.; B. Herut; Johansen, A.M.; N. Kubilay; Losno, R.

    2009-01-01

    Atmospheric inputs of iron to the open ocean are hypothesized to modulate ocean biogeochemistry. This review presents an integration of available observations of atmospheric iron and iron deposition, and also covers bioavailable iron distributions. Methods for estimating temporal variability in ocean deposition over the recent past are reviewed. Desert dust iron is estimated to represent 95% of the global atmospheric iron cycle, and combustion sources of iron are responsible for the remaining...

  8. Tungsten Deposition on Graphite using Plasma Enhanced Chemical Vapour Deposition.

    Science.gov (United States)

    Sharma, Uttam; Chauhan, Sachin S.; Sharma, Jayshree; Sanyasi, A. K.; Ghosh, J.; Choudhary, K. K.; Ghosh, S. K.

    2016-10-01

    The tokamak concept is the frontrunner for achieving controlled thermonuclear reaction on earth, an environment friendly way to solve future energy crisis. Although much progress has been made in controlling the heated fusion plasmas (temperature ∼ 150 million degrees) in tokamaks, technological issues related to plasma wall interaction topic still need focused attention. In future, reactor grade tokamak operational scenarios, the reactor wall and target plates are expected to experience a heat load of 10 MW/m2 and even more during the unfortunate events of ELM's and disruptions. Tungsten remains a suitable choice for the wall and target plates. It can withstand high temperatures, its ductile to brittle temperature is fairly low and it has low sputtering yield and low fuel retention capabilities. However, it is difficult to machine tungsten and hence usages of tungsten coated surfaces are mostly desirable. To produce tungsten coated graphite tiles for the above-mentioned purpose, a coating reactor has been designed, developed and made operational at the SVITS, Indore. Tungsten coating on graphite has been attempted and successfully carried out by using radio frequency induced plasma enhanced chemical vapour deposition (rf -PECVD) for the first time in India. Tungsten hexa-fluoride has been used as a pre-cursor gas. Energy Dispersive X-ray spectroscopy (EDS) clearly showed the presence of tungsten coating on the graphite samples. This paper presents the details of successful operation and achievement of tungsten coating in the reactor at SVITS.

  9. Deposition of dielectric films on silicon using a fore-vacuum plasma electron source.

    Science.gov (United States)

    Zolotukhin, D B; Oks, E M; Tyunkov, A V; Yushkov, Yu G

    2016-06-01

    We describe an experiment on the use of a fore-vacuum-pressure, plasma-cathode, electron beam source with current up to 100 mA and beam energy up to 15 keV for deposition of Mg and Al oxide films on Si substrates in an oxygen atmosphere at a pressure of 10 Pa. The metals (Al and Mg) were evaporated and ionized using the electron beam with the formation of a gas-metal beam-plasma. The plasma was deposited on the surface of Si substrates. The elemental composition of the deposited films was analyzed.

  10. Deposition of dielectric films on silicon using a fore-vacuum plasma electron source

    Energy Technology Data Exchange (ETDEWEB)

    Zolotukhin, D. B.; Tyunkov, A. V.; Yushkov, Yu. G., E-mail: yuyushkov@gmail.com [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Ave., Tomsk 634050 (Russian Federation); Oks, E. M. [Tomsk State University of Control Systems and Radioelectronics, 40 Lenin Ave., Tomsk 634050 (Russian Federation); Institute of High Current Electronics SB RAS, 2/3, Akademichesky Ave., Tomsk 634055 (Russian Federation)

    2016-06-15

    We describe an experiment on the use of a fore-vacuum-pressure, plasma-cathode, electron beam source with current up to 100 mA and beam energy up to 15 keV for deposition of Mg and Al oxide films on Si substrates in an oxygen atmosphere at a pressure of 10 Pa. The metals (Al and Mg) were evaporated and ionized using the electron beam with the formation of a gas-metal beam-plasma. The plasma was deposited on the surface of Si substrates. The elemental composition of the deposited films was analyzed.

  11. [Multivariate analysis of heavy metal element concentrations in atmospheric deposition in Harbin City, northeast China].

    Science.gov (United States)

    Tang, Jie; Han, Wei-Zheng; Li, Na; Li, Zhao-Yang; Bian, Jian-Min; Li, Hai-Yi

    2011-11-01

    In order to understand the characteristics of atmospheric heavy metal deposition in Harbin City, 46 deposition samples were collected which were taken using bulk deposition samplers during the period of 2008-2009 (about 365 days). The samples were analyzed for heavy metal concentration by atomic fluorescence spectrometry (AFS) and inductively coupled plasma-atomic spectrometry (ICP-AES). The deposition flux was calculated. Sources analysis was made by the method of principal component analysis (PCA), Pearsons and enrichment factor (EF). The following points can be gained through multivariate analysis. Mn and Co are mostly from natural sources while the others may be brought by coal dust, vehicle emissions and metal smelting.

  12. Plasma deposition of antimicrobial coating on organic polymer

    Science.gov (United States)

    Rżanek-Boroch, Zenobia; Dziadczyk, Paulina; Czajkowska, Danuta; Krawczyk, Krzysztof; Fabianowski, Wojciech

    2013-02-01

    Organic materials used for packing food products prevent the access of microorganisms or gases, like oxygen or water vapor. To prolong the stability of products, preservatives such as sulfur dioxide, sulfites, benzoates, nitrites and many other chemical compounds are used. To eliminate or limit the amount of preservatives added to food, so-called active packaging is sought for, which would limit the development of microorganisms. Such packaging can be achieved, among others, by plasma modification of a material to deposit on its surface substances inhibiting the growth of bacteria. In this work plasma modification was carried out in barrier discharge under atmospheric pressure. Sulfur dioxide or/and sodium oxide were used as the coating precursors. As a result of bacteriological studies it was found that sulfur containing coatings show a 16% inhibition of Salmonella bacteria growth and 8% inhibition of Staphylococcus aureus bacteria growth. Sodium containing coatings show worse (by 10%) inhibiting properties. Moreover, films with plasma deposited coatings show good sealing properties against water vapor. Contribution to the Topical Issue "13th International Symposium on High Pressure Low Temperature Plasma Chemistry (Hakone XIII)", Edited by Nicolas Gherardi, Henryca Danuta Stryczewska and Yvan Ségui.

  13. Solid Carbon Produced in an Inductively Coupled Plasma Torch with a Titan Like Atmosphere

    Directory of Open Access Journals (Sweden)

    D. Vacher

    2013-01-01

    Full Text Available Solid carbon is deposited on the surfaces of an inductively coupled plasma torch operating with a Titan like atmosphere plasma gas. The frame of the initial research is the study of the radiative properties of plasma encountered around a spacecraft during its hypersonic entry in upper layers of planetary atmosphere. Deposition of carbon is observed not only on the quartz tube outside the inductor but also on the ceramic protection of the torch injector. Carbon exhibits two types of morphology more or less dense and it is analyzed by various analytic devices as MEB, SEM, TEM, EDS and Raman spectroscopy. The gathered carbon powder shows the presence of nanostructured particles.

  14. Durable Nanolayer Graft Polymerization of Functional Finishes Using Atmospheric Plasma

    Science.gov (United States)

    Mazloumpour, Maryam

    Various applications of atmospheric pressure plasma were investigated in conjunction with different chemistries on nonwoven materials including spunbond polyester (PET) and spunbod polypropylene for fuel separation and antimicrobial functionalities. Hydrophobic/Oleophobic properties were conferred on nonwoven polyester (PET) via plasma-induced graft polymerization of different hydrophobic non-C8 perfluorocarbon chemistry including perfluorohexylethylmethacrylate, perfluorohexylethylacrylate, allylpentafluorobenzene, pentafluorostyrene, or 1,3-divinyltetramethyldisiloxane in the vapor form using both in-situ and down-stream plasma configurations. Different nanolayers of the grafted polymer were furnished on nonwovens to generate surfaces with different level of wettabilities for medical applications and water/fuel separation. The effect of various hydrophobic chemistry, different plasma conditions, and plasma device parameters including plasma power and plasma exposure time were studied and the performance was characterized by measuring the contact angle and the wettability rating against liquids with broad range of surface tensions. Vapor deposition of 2-(perfluorohexyl)ethyl methacrylate and pentafluorostyrene on nonwoven PET followed by plasma-induced graft polymerization was investigated for possible use in water/fuel separation. Different nanolayer thicknesses (80-180nm) of the grafted polymer were achieved to generate surfaces with different wettabilities for water/fuel separation of different fuel compositions. The effect of different plasma conditions and device parameters including the flow rate of monomers, power of the device, and time of plasma exposure on the separation of different fuels was studied and characterized by measuring the surface energy of the treated substrates. The surface chemistry and morphology of the treated samples were characterized using XPS, SEM and TOF-SIMS techniques which confirmed the grafting of monomer onto the substrate

  15. Plasma Enhanced Chemical Vapour Deposition of Horizontally Aligned Carbon Nanotubes

    Directory of Open Access Journals (Sweden)

    Matthew T. Cole

    2013-05-01

    Full Text Available A plasma-enhanced chemical vapour deposition reactor has been developed to synthesis horizontally aligned carbon nanotubes. The width of the aligning sheath was modelled based on a collisionless, quasi-neutral, Child’s law ion sheath where these estimates were empirically validated by direct Langmuir probe measurements, thereby confirming the proposed reactors ability to extend the existing sheath fields by up to 7 mm. A 7 mbar growth atmosphere combined with a 25 W plasma permitted the concurrent growth and alignment of carbon nanotubes with electric fields of the order of 0.04 V μm−1 with linear packing densities of up to ~5 × 104 cm−1. These results open up the potential for multi-directional in situ alignment of carbon nanotubes providing one viable route to the fabrication of many novel optoelectronic devices.

  16. Plasma-Assisted Atomic Layer Deposition: Basics, Opportunities, and Challenges

    NARCIS (Netherlands)

    Profijt, H. B.; Potts, S. E.; M. C. M. van de Sanden,; Kessels, W. M. M.

    2011-01-01

    Plasma-assisted atomic layer deposition (ALD) is an energy-enhanced method for the synthesis of ultra-thin films with A angstrom-level resolution in which a plasma is employed during one step of the cyclic deposition process. The use of plasma species as reactants allows for more freedom in processi

  17. Plasma-Assisted Atomic Layer Deposition: Basics, Opportunities, and Challenges

    NARCIS (Netherlands)

    Profijt, H. B.; Potts, S. E.; M. C. M. van de Sanden,; Kessels, W. M. M.

    2011-01-01

    Plasma-assisted atomic layer deposition (ALD) is an energy-enhanced method for the synthesis of ultra-thin films with A angstrom-level resolution in which a plasma is employed during one step of the cyclic deposition process. The use of plasma species as reactants allows for more freedom in

  18. Atmospheric nitrogen compounds: Occurrence, composition and deposition

    DEFF Research Database (Denmark)

    Nielsen, T.; Pilegaard, K.; Egeløv, A.H.;

    1996-01-01

    Traffic in cities and on highways is an important contributor to NOy atmospheric pollution in open areas. In this situation both the concentration and composition of NOy compounds show a wide variation and are dependent on meteorological and atmospheric chemical conditions. The proportion of NOz...

  19. Atmospheric Pressure Plasma Processing for Polymer Adhesion: A Review

    DEFF Research Database (Denmark)

    Kusano, Yukihiro

    2014-01-01

    Atmospheric pressure plasma processing has attracted significant interests over decades due to its usefulness and a variety of applications. Adhesion improvement of polymer surfaces is among the most important applications of atmospheric pressure plasma treatment. Reflecting recent significant de...... development of the atmospheric pressure plasma processing, this work presents its fundamental aspects, applications, and characterization techniques relevant to adhesion.......Atmospheric pressure plasma processing has attracted significant interests over decades due to its usefulness and a variety of applications. Adhesion improvement of polymer surfaces is among the most important applications of atmospheric pressure plasma treatment. Reflecting recent significant...

  20. Atmospheric heavy metal deposition in Europe estimated by moss analysis

    Energy Technology Data Exchange (ETDEWEB)

    Ruehling, Aa. [Swedish Environmental Research Inst., Lund (Sweden). Dept. of Ecology

    1995-12-31

    Atmospheric heavy metal deposition in Europe including 21 countries was monitored in 1990-1992 by the moss technique. This technique is based on the fact that the concentrations of heavy metals in moss are closely correlated to atmospheric deposition. This was the first attempt to map heavy metal deposition in this large area. The objectives of the project were to characterise qualitatively and quantitatively the regional atmospheric deposition pattern of heavy metals in background areas in Europe, to indicate the location of important heavy metal pollution sources and to allow retrospective comparisons with similar studies. The present survey is a follow-up of a joint Danish and Swedish project in 1980 and an extended survey in 1985 within the framework of the Nordic Council of Ministers. In Sweden, heavy-metal deposition was first mapped on a nation-wide scale in 1968-1971 and 1975. (author)

  1. A New Atmospheric Pressure Microwave Plasma Source (APMPS)

    Institute of Scientific and Technical Information of China (English)

    LIU Liang; ZHANG Guixin; LI Yinan; ZHU Zhijie; WANG Xinxin; LUO Chengmu

    2008-01-01

    An atmospheric pressure microwave plasma source (APMPS) that can generate a large volume of plasma at an atmospheric pressure has been developed at Tsinghua University. This paper presents the design of this APMPS, the theoretical consideration of microwave plasma ignition and the simulation results, including the distributions of the electric field and power density inside the cavity as well as the accuracy of the simulation results. In addition, a method of producing an atmospheric pressure microwave plasma and some relevant observations of the plasma are also provided. It. is expected that this research would be useful for further developing atmospheric pressure microwave plasma sources and expanding the scope of their applications.

  2. Deposition of SiOx films by means of atmospheric pressure microplasma jets

    CERN Document Server

    Benedikt, Jan; Ellerweg, Dirk; Rügner, Katja; von Keudell, Achim

    2011-01-01

    Atmospheric pressure plasma jet sources are currently in the focus of many researchers for their promising applications in medical industry (e.g. treatment of living tissues), surface modification or material etching or synthesis. Here we report on the study of fundamental principles of deposition of SiOx films from microplasma jets with admixture of hexamethyldisiloxane [(CH3)3SiOSi(CH3)3, HMDSO] molecules and oxygen. The properties of the deposited films, the composition of the plasma as measured by molecular beam mass spectrometry and the effect of additional treatment of grown film by oxygen or hydrogen atoms will be presented.

  3. Spatial atmospheric atomic layer deposition of alxzn1-xo

    NARCIS (Netherlands)

    Illiberi, A.; Scherpenborg, R.; Wu, Y.; Roozeboom, F.; Poodt, P.

    2013-01-01

    The possibility of growing multicomponent oxides by spatial atmospheric atomic layer deposition has been investigated. To this end, Al xZn1-xO films have been deposited using diethyl zinc (DEZ), trimethyl aluminum (TMA), and water as Zn, Al, and O precursors, respectively. When the metal precursors

  4. Nanostructured Sulfide Composite Coating Prepared by Atmospheric Plasma Spraying

    Institute of Scientific and Technical Information of China (English)

    关耀辉

    2006-01-01

    Nanostructured FeS-SiC coating was deposited by atmospheric plasma spraying (APS). The microstructure and phase composition of the coating were characterized with SEM and XRD, respectively. In addition, the size distribution of the reconstituted powders and the porosity of the coating have been measured. It was found that the reconstitiuted powers with sizes in the range of 20 to 80 μm had excellent flowability and were suitable for plasma spraying process. The assprayed FeS-SiC composite coating exhibited a bimodal distribution with small grains (30~80nm) and large grains (100~200nm). The coating was mainly composed of FeS and SiC, a small quantity of Fe1-x S and oxide were also found. The porosity of the coating was approximately 19 %.

  5. New development of atmospheric pressure plasma polishing

    Institute of Scientific and Technical Information of China (English)

    Bo Wang; Jufan Zhang; Shen Dong

    2009-01-01

    Atmospheric pressure plasma polishing (APPP) is a precision machining technology used for manufacturing high quality optical surfaces. The changes of surface modulus and hardness after machining prove the distinct improvement of surface mechanical properties. The demonstrated decrease of surfacc residual stresses testifies the removal of the former deformation layer.And the surface topographies under atomic force microscope (AFM) and scanning electron microscope (SEM) indicate obvious amelioration of the surface status,showing that the 0.926-nm average surface roughness has been achieved.

  6. Atmospheric Sulfur Deposition on Farmland in East China

    Institute of Scientific and Technical Information of China (English)

    WANG Ti-Jian; YANG Hao-Ming; GAO Li-Jie; ZHANG Yan; HU Zheng-Yi; XU Cheng-Kai

    2005-01-01

    Atmospheric sulfur deposition onto typical farmland in East China was investigated using both field measurements and numerical modeling. The field measurements were conducted at the Experiment Station of Red Soil Ecology, Chinese Academy of Sciences, 10 km from Yingtan, Jiangxi Province, East China, between November 1998 and October 1999, and at the Changshu Ecological Experiment Station, Chinese Academy of Sciences, in a rapidly developing region of Jiangsu Province, East China, between April 2001 and March 2002. The regional acid deposition model system (RegADMS), in which the dry deposition velocities of SO2 and sulfate aerosols (SO42-) were estimated using a big-leaf resistance analogy model, was applied to simulate air sulfur deposition over East China and sulfur deposition onto lands of different use types in East China. The wet scavenging coefficients were parameterized in terms of precipitation rate, and the effect of sub-grid processes due to inhomogeneous land use on dry deposition velocity was also included. Results of the field measurements showed that over 83% of the total sulfur deposition at the Yingtan site was dry deposition, while at the Changshu site42% was dry deposition. The total sulfur deposition was much larger at the Yingtan site than at the Changshu site, which suggested contrasting air pollution and meteorological situations. The modeling results revealed that the total annual sulfur deposition over East China was 1.88 Mt, of which 72.8% was deposited onto farmland, and dry deposition accounted for 43% of the total sulfur deposited. The modeling results were generally in agreement with those from the observations.Overall, this study suggested that atmospheric sulfur deposition played an important role in the soil sulfur balance, which could have a significant effect on agricultural ecosystems in the study region.

  7. Atmospheric iron deposition: global distribution, variability, and human perturbations.

    Science.gov (United States)

    Mahowald, Natalie M; Engelstaedter, Sebastian; Luo, Chao; Sealy, Andrea; Artaxo, Paulo; Benitez-Nelson, Claudia; Bonnet, Sophie; Chen, Ying; Chuang, Patrick Y; Cohen, David D; Dulac, Francois; Herut, Barak; Johansen, Anne M; Kubilay, Nilgun; Losno, Remi; Maenhaut, Willy; Paytan, Adina; Prospero, Joseph M; Shank, Lindsey M; Siefert, Ronald L

    2009-01-01

    Atmospheric inputs of iron to the open ocean are hypothesized to modulate ocean biogeochemistry. This review presents an integration of available observations of atmospheric iron and iron deposition, and also covers bioavailable iron distributions. Methods for estimating temporal variability in ocean deposition over the recent past are reviewed. Desert dust iron is estimated to represent 95% of the global atmospheric iron cycle, and combustion sources of iron are responsible for the remaining 5%. Humans may be significantly perturbing desert dust (up to 50%). The sources of bioavailable iron are less well understood than those of iron, partly because we do not know what speciation of the iron is bioavailable. Bioavailable iron can derive from atmospheric processing of relatively insoluble desert dust iron or from direct emissions of soluble iron from combustion sources. These results imply that humans could be substantially impacting iron and bioavailable iron deposition to ocean regions, but there are large uncertainties in our understanding.

  8. Observations of atmospheric chemical deposition to high Arctic snow

    Science.gov (United States)

    Macdonald, Katrina M.; Sharma, Sangeeta; Toom, Desiree; Chivulescu, Alina; Hanna, Sarah; Bertram, Allan K.; Platt, Andrew; Elsasser, Mike; Huang, Lin; Tarasick, David; Chellman, Nathan; McConnell, Joseph R.; Bozem, Heiko; Kunkel, Daniel; Duan Lei, Ying; Evans, Greg J.; Abbatt, Jonathan P. D.

    2017-05-01

    Rapidly rising temperatures and loss of snow and ice cover have demonstrated the unique vulnerability of the high Arctic to climate change. There are major uncertainties in modelling the chemical depositional and scavenging processes of Arctic snow. To that end, fresh snow samples collected on average every 4 days at Alert, Nunavut, from September 2014 to June 2015 were analyzed for black carbon, major ions, and metals, and their concentrations and fluxes were reported. Comparison with simultaneous measurements of atmospheric aerosol mass loadings yields effective deposition velocities that encompass all processes by which the atmospheric species are transferred to the snow. It is inferred from these values that dry deposition is the dominant removal mechanism for several compounds over the winter while wet deposition increased in importance in the fall and spring, possibly due to enhanced scavenging by mixed-phase clouds. Black carbon aerosol was the least efficiently deposited species to the snow.

  9. Antireflection coatings on plastics deposited by plasma polymerization process

    Indian Academy of Sciences (India)

    K M K Srivatsa; M Bera; A Basu; T K Bhattacharya

    2008-08-01

    Antireflection coatings (ARCs) are deposited on the surfaces of optical elements like spectacle lenses to increase light transmission and improve their performance. In the ophthalmic industry, plastic lenses are rapidly displacing glass lenses due to several advantageous features. However, the deposition of ARCs on plastic lenses is a challenging task, because the plastic surface needs treatment for adhesion improvement and surface hardening before depositing the ARC. This surface treatment is usually done in a multi-stage process—exposure to energetic radiations, followed by deposition of a carbonyl hard coating by spin or dip coating processes, UV curing, etc. However, this treatment can also be done by plasma processes. Moreover, the plasma polymerization process allows deposition of optical films at room temperature, essential for plastics. The energetic ions in plasma processes provide similar effects as in ion assisted physical deposition processes to produce hard coatings, without requiring sophisticated ion sources. The plasma polymerization process is more economical than ion-assisted physical vapour deposition processes as regards equipment and source materials and is more cost-effective, enabling the surface treatment and deposition of the ARC in the same deposition system in a single run by varying the system parameters at each step. Since published results of the plasma polymerization processes developed abroad are rather sketchy and the techniques are mostly veiled in commercial secrecy, innovative and indigenous plasma-based techniques have been developed in this work for depositing the complete ARCs on plastic substrates.

  10. Methane coupling in microwave plasma under atmospheric pressure

    Institute of Scientific and Technical Information of China (English)

    Changsheng Shen; Dekun Sun; Hongsheng Yang

    2011-01-01

    Methane coupling in microwave plasma under atmospheric pressure has been investigated.The effects of molar ratio n(CH4)/n(H2),flow rate and microwave power on the reaction have been studied.(1) With the decrease of n(CH4)/n(H2) ratio,methane conversion,C2 hydrocarbon yield,energy yield and space-time yield of acetylene increased,but the yield of carbon deposit decreased.(2) With the increase of microwave power,energy yield of acetylene decreased,but space-time yield of acetylene increased.(3) With the increase of flow rate,energy yield and space-time yield of acetylene increased first and then decreased.Finally,under the reaction conditions of CH4 flow rate of 700 mL/min,n(CH4)/n(H2) ratio of 1/4 and microwave power of 400 W,the energy yield and space-time yield of acetylene could reach 0.337 mmol/kJ and 12.3 mol/(s·m3),respectively.The reaction mechanism of methane coupling in microwave plasma has been investigated based on the thermodynamics of chemical reaction.Interestingly,the acetylene yield of methane coupling in microwave plasma was much higher than the maximum thermodynamic yield of acetylene.This phenomenon was tentatively explained from non-expansion work in the microwave plasma system.

  11. Surface functionalization of PET fabric with atmospheric pressure plasma enhanced chemical vapor deposition%常压等离子体增强化学气相沉积法表面功能化聚酯织物

    Institute of Scientific and Technical Information of China (English)

    K. H. Kale; S. S. Palaskar; 刘鹏(译); 罗艳(校)

    2012-01-01

    Plasma technology is emerging as a novel and environmentally friendly technology for surface modification of textile materials. It is possible to deposit very thin film with specific functional properties on the surface of textiles. The current study describes a novel approach for surface modification of 100% polyester textiles with plasma enhanced chemical vapor deposition (PECVD). The chemical and structural nature of plasma polymers deposited at the surface of the samples with respect to discharge power was studied with FTIR spectroscopy. The functional property i. e. water repellency imparted was determined with spray test and contact angle measurement.%对于纺织材料的表面改性来说,等离子体技术正成为一种新兴且环境友好的技术。等离子体技术在纺织品表面可沉积具有特殊功能的薄膜。阐述了一种常压等离子体增强化学气相沉积法表面改性100%聚酯织物的新型方法。通过傅里叶变换红外光谱研究了沉积于样品表面上相对于放电功率的等离子体聚合物化学和结构性质。采用雾化试验和接触角测量赋予织物诸如疏水等的功能特性。

  12. Atmospheric Deposition of Sulfur and Base Cations to European Forests

    OpenAIRE

    Ivens, W.

    1988-01-01

    To simulate acidification processes in forests (soils), it is important to know as well as possible the atmospheric input. Large scale models have recently been improved to take better into account the differences in deposition between forests and other surfaces. In this report measurements of sulfur-fluxes onto the forest floor (54 case studies) are compared with deposition fluxes as calculated by the EMEP-model and by the RAINS modifications on this model. The value of the filtering pa...

  13. Synthesis and texturization processes of (super)-hydrophobic fluorinated surfaces by atmospheric plasma

    CERN Document Server

    Hubert, Julie; Dufour, Thierry; Vandencasteele, Nicolas; Reniers, François; Viville, Pascal; Lazzaroni, Roberto; Raes, M; Terryn, Herman

    2016-01-01

    The synthesis and texturization processes of fluorinated surfaces by means of atmospheric plasma are investigated and presented through an integrated study of both the plasma phase and the resulting material surface. Three methods enhancing the surface hydrophobicity up to the production of super-hydrophobic surfaces are evaluated: (i) the modification of a polytetrafluoroethylene (PTFE) surface, (ii) the plasma deposition of fluorinated coatings and (iii) the incorporation of nanoparticles into those fluorinated films. In all the approaches, the nature of the plasma gas appears to be a crucial parameter for the desired property. Although a higher etching of the PTFE surface can be obtained with a pure helium plasma, the texturization can only be created if O2 is added to the plasma, which simultaneously decreases the total etching. The deposition of CxFy films by a dielectric barrier discharge leads to hydrophobic coatings with water contact angles (WCAs) of 115{\\textdegree}, but only the filamentary argon d...

  14. Martian Atmospheric and Ionospheric plasma Escape

    Science.gov (United States)

    Lundin, Rickard

    2016-04-01

    Solar forcing is responsible for the heating, ionization, photochemistry, and erosion processes in the upper atmosphere throughout the lifetime of the terrestrial planets. Of the four terrestrial planets, the Earth is the only one with a fully developed biosphere, while our kin Venus and Mars have evolved into arid inhabitable planets. As for Mars, there are ample evidences for an early Noachian, water rich period on Mars. The question is, what made Mars evolve so differently compared to the Earth? Various hydrosphere and atmospheric evolution scenarios for Mars have been forwarded based on surface morphology, chemical composition, simulations, semi-empiric (in-situ data) models, and the long-term evolution of the Sun. Progress has been made, but the case is still open regarding the changes that led to the present arid surface and tenuous atmosphere at Mars. This presentation addresses the long-term variability of the Sun, the solar forcing impact on the Martian atmosphere, and its interaction with the space environment - an electromagnetic wave and particle interaction with the upper atmosphere that has implications for its photochemistry, composition, and energization that governs thermal and non-thermal escape. Non-thermal escape implies an electromagnetic upward energization of planetary ions and molecules to velocities above escape velocity, a process governed by a combination of solar EUV radiation (ionization), and energy and momentum transfer by the solar wind. The ion escape issue dates back to the early Soviet and US-missions to Mars, but the first more accurate estimates of escape rates came with the Phobos-2 mission in 1989. Better-quality ion composition measurement results of atmospheric/ionospheric ion escape from Mars, obtained from ESA Mars Express (MEX) instruments, have improved our understanding of the ion escape mechanism. With the NASA MAVEN spacecraft orbiting Mars since Sept. 2014, dual in-situ measurement with plasma instruments are now

  15. Total atmospheric mercury deposition in forested areas in South Korea

    Science.gov (United States)

    Han, Jin-Su; Seo, Yong-Seok; Kim, Moon-Kyung; Holsen, Thomas M.; Yi, Seung-Muk

    2016-06-01

    In this study, mercury (Hg) was sampled weekly in dry and wet deposition and throughfall and monthly in litterfall, and as it was volatilized from soil from August 2008 to February 2010 to identify the factors influencing the amount of atmospheric Hg deposited to forested areas in a temperate deciduous forest in South Korea. For this location there was no significant correlation between the estimated monthly dry deposition flux (litterfall + throughfall - wet deposition) (6.7 µg m-2 yr-1) and directly measured dry deposition (9.9 µg m-2 yr-1) likely due primarily to Hg losses from the litterfall collector. Dry deposition fluxes in cold seasons (fall and winter) were lower than in warmer seasons (spring and summer). The volume-weighted mean (VWM) Hg concentrations in both precipitation and throughfall were highest in winter, likely due to increased scavenging by snow events. Since South Korea experiences abundant rainfall in summer, VWM Hg concentrations in summer were lower than in other seasons. Litterfall fluxes were highest in the late fall to early winter, when leaves were dropped from the trees (September to November). The cumulative annual Hg emission flux from soil was 6.8 µg m-2 yr-1. Based on these data, the yearly deposition fluxes of Hg calculated using two input approaches (wet deposition + dry deposition or throughfall + litterfall) were 6.8 and 3.6 µg m-2 yr-1, respectively. This is the first reported study which measured the amount of atmospheric Hg deposited to forested areas in South Korea, and thus our results provide useful information to compare against data related to Hg fate and transport in this part of the world.

  16. Atmospheric Deposition of Phosphorus to the Everglades: Concepts, Constraints, and Published Deposition Rates for Ecosystem Management

    Directory of Open Access Journals (Sweden)

    Garth W. Redfield

    2002-01-01

    Full Text Available This paper summarizes concepts underlying the atmospheric input of phosphorus (P to ecosystems, published rates of P deposition, measurement methods, and approaches to future monitoring and research. P conveyed through the atmosphere can be a significant nutrient source for some freshwater and marine ecosystems. Particle sources and sinks at the land-air interface produce variation in P deposition from the atmosphere across temporal and spatial scales. Natural plant canopies can affect deposition rates by changing the physical environment and surface area for particle deposition. Land-use patterns can alter P deposition rates by changing particle concentrations in the atmosphere. The vast majority of P in dry atmospheric deposition is conveyed by coarse (2.5 to 10 μm and giant (10 to 100 μm particles, and yet these size fractions represent a challenge for long-term atmospheric monitoring in the absence of accepted methods for routine sampling. Most information on P deposition is from bulk precipitation collectors and wet/dry bucket sampling, both with questionable precision and accuracy. Most published annual rates of P deposition are gross estimates derived from bulk precipitation sampling in locations around the globe and range from about 5 to well over 100 mg P m–2 year–1, although most inland ecosystems receive between 20 and 80 mg P m–2 year–1. Rates below 30 mg P m–2 year–1 are found in remote areas and near coastlines. Intermediate rates of 30 to 50 mg P m–2 year–1 are associated with forests or mixed land use, and rates of 50 to 100 mg P m–2 year–1 or more are often recorded from urban or agricultural settings. Comparison with other methods suggests that these bulk precipitation estimates provide crude boundaries around actual P deposition rates for various land uses. However, data screening cannot remove all positive bias caused by contamination of bucket or bulk collectors. As a consequence, continued sampling

  17. Destruction mechanisms for formaldehyde in atmospheric pressure low temperature plasmas

    Science.gov (United States)

    Storch, Daniel G.; Kushner, Mark J.

    1993-01-01

    Formaldehyde (CH2O) is a common pollutant of indoor air in residences and commercial buildings. The removal of CH2O from atmospheric pressure gas streams (N2/O2/H2O/CH2O) using plasmas generated by a dielectric barrier discharge has been theoretically investigated with the goal of cleansing indoor air. The model consists of a full accounting of the electron, ion, and neutral chemical kinetics in contaminated humid air. We find that the destruction of CH2O results dominantly from chemical attack by OH and O radicals, with the primary end products being CO and H2O. The predicted destruction rates for CH2O are typically 2-8 ppm/(mJ cm-3) (parts per million of CH2O in air/energy deposition). The elimination of the unwanted byproducts, CO and NO, using a platinum catalyst is discussed.

  18. Atmospheric deposition to forests in the eastern USA

    Science.gov (United States)

    Risch, Martin R.; DeWild, John F.; Gay, David A.; Zhang, Leiming; Boyer, Elizabeth W.; Krabbenhoft, David P.

    2017-01-01

    Atmospheric mercury (Hg) deposition to forests is important because half of the land cover in the eastern USA is forest. Mercury was measured in autumn litterfall and weekly precipitation samples at a total of 27 National Atmospheric Deposition Program (NADP) monitoring sites in deciduous and mixed deciduous-coniferous forests in 16 states in the eastern USA during 2007–2014. These simultaneous, uniform, repeated, annual measurements of forest Hg include the broadest area and longest time frame to date. The autumn litterfall-Hg concentrations and litterfall mass at the study sites each year were combined with annual precipitation-Hg data. Rates of litterfall-Hg deposition were higher than or equal to precipitation-Hg deposition rates in 70% of the annual data, which indicates a substantial contribution from litterfall to total atmospheric-Hg deposition. Annual litterfall-Hg deposition in this study had a median of 11.7 μg per square meter per year (μg/m2/yr) and ranged from 2.2 to 23.4 μg/m2/yr. It closely matched modeled dry-Hg deposition, based on land cover at selected NADP Hg-monitoring sites. Mean annual atmospheric-Hg deposition at forest study sites exhibited a spatial pattern partly explained by statistical differences among five forest-cover types and related to the mapped density of Hg emissions. Forest canopies apparently recorded changes in atmospheric-Hg concentrations over time because litterfall-Hg concentrations decreased year to year and litterfall-Hg concentrations were significantly higher in 2007–2009 than in 2012–2014. These findings reinforce reported decreases in Hg emissions and atmospheric elemental-Hg concentrations during this same time period. Methylmercury (MeHg) was detected in all litterfall samples at all sites, compared with MeHg detections in less than half the precipitation samples at selected sites during the study. These results indicate MeHg in litterfall is a pathway into the terrestrial food web where it can

  19. Cleaning of carbon materials from flat surfaces and castellation gaps by an atmospheric pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Stancu, C. [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania); Alegre, D. [Laboratorio Nacional de Fusión, As. Euratom/Ciemat, Avda. Complutense 22, 28040, Madrid (Spain); Ionita, E.R.; Mitu, B. [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania); Grisolia, C. [CEA, IRFM, F-13108, Saint-Paul-lez-Durance (France); Tabares, F.L. [Laboratorio Nacional de Fusión, As. Euratom/Ciemat, Avda. Complutense 22, 28040, Madrid (Spain); Dinescu, G., E-mail: dinescug@infim.ro [National Institute for Laser, Plasma and Radiation Physics, Atomistilor Str. 409, PO Box Mg36, Magurele-Bucharest, 077125 (Romania)

    2016-02-15

    Highlights: • Atmospheric plasma jets operated with nitrogen, oxygen and their mixtures are used for cleaning surfaces of carbon residues • Efficient plasma jet cleaning of carbon deposits from flat surfaces and inside gaps of castellated surfaces is demonstrated • Plasma jet cleaning is more effective at the gaps entrance and on their bottom - Abstract: A study of the removal of carbon layers from flat and castellated surfaces by a plasma jet source operated in open atmosphere is presented. Amorphous hydrogenated carbon films deposited on silicon substrates, on aluminium made castellated surfaces, and graphitic carbon plates were used. The erosion effects of plasmas generated either in pure argon, nitrogen or in their mixtures with hydrogen, ammonia, oxygen are compared. Highest erosion was obtained with nitrogen and nitrogen/oxygen plasmas. Plasmas in argon and containing hydrogen, and ammonia have shown a low erosion rate. A large removal rate by pure nitrogen plasma jet of 3.2 mg/min was found by scanning graphitic carbon flat surfaces for optimum process parameters. Adding small quantities of oxygen led to a removal rate enhancement by a factor of 3. Finally, the integral removal rate of amorphous hydrogenated carbon deposited in gaps 23 mm deep and 0.5 mm wide was of the order of 0.35 mg/min. The layer elimination was more efficient at the top and at the bottom of the gaps, precisely where the thickest codeposits develop in a nuclear fusion device.

  20. Plasma sprayed and electrospark deposited zirconium metal diffusion barrier coatings

    Energy Technology Data Exchange (ETDEWEB)

    Hollis, Kendall J [Los Alamos National Laboratory; Pena, Maria I [Los Alamos National Laboratory

    2010-01-01

    Zirconium metal coatings applied by plasma spraying and electrospark deposition (ESD) have been investigated for use as diffusion barrier coatings on low enrichment uranium fuel for research nuclear reactors. The coatings have been applied to both stainless steel as a surrogate and to simulated nuclear fuel uranium-molybdenum alloy substrates. Deposition parameter development accompanied by coating characterization has been performed. The structure of the plasma sprayed coating was shown to vary with transferred arc current during deposition. The structure of ESD coatings was shown to vary with the capacitance of the deposition equipment.

  1. Atmospheric Pressure Low Temperature Plasma System for Additive Manufacturing

    Science.gov (United States)

    Burnette, Matthew; Staack, David

    2016-09-01

    There is growing interest in using plasmas for additive manufacturing, however these methods use high temperature plasmas to melt the material. We have developed a novel technique of additive manufacturing using a low temperature dielectric barrier discharge (DBD) jet. The jet is attached to the head of a 3D printer to allow for precise control of the plasma's location. Various methods are employed to deposit the material, including using a vaporized precursor or depositing a liquid precursor directly onto the substrate or into the plasma via a nebulizer. Various materials can be deposited including metals (copper using copper (II) acetylacetonate), polymers (PMMA using the liquid monomer), and various hydrocarbon compounds (using alcohols or a 100% methane DBD jet). The rastering pattern for the 3D printer was modified for plasma deposition, since it was originally designed for thermoplastic extrusion. The design constraints for fill pattern selection for the plasma printer are influenced by substrate heating, deposition area, and precursor consumption. Depositions onto pressure and/or temperature sensitive substrates can be easily achieved. Deposition rates range up to 0.08 cm3/hr using tris(2-methoxyethoxy)(vinyl)silane, however optimization can still be done on the system to improve the deposition rate. For example higher concentration of precursor can be combined with faster motion and higher discharge powers to increase the deposition rate without overheating the substrate.

  2. The annual averaged atmospheric dispersion factor and deposition factor according to methods of atmospheric stability classification

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Hae Sun; Jeong, Hyo Joon; Kim, Eun Han; Han, Moon Hee; Hwang, Won Tae [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-09-15

    This study analyzes the differences in the annual averaged atmospheric dispersion factor and ground deposition factor produced using two classification methods of atmospheric stability, which are based on a vertical temperature difference and the standard deviation of horizontal wind direction fluctuation. Daedeok and Wolsong nuclear sites were chosen for an assessment, and the meteorological data at 10 m were applied to the evaluation of atmospheric stability. The XOQDOQ software program was used to calculate atmospheric dispersion factors and ground deposition factors. The calculated distances were chosen at 400 m, 800 m, 1,200 m, 1,600 m, 2,400 m, and 3,200 m away from the radioactive material release points. All of the atmospheric dispersion factors generated using the atmospheric stability based on the vertical temperature difference were shown to be higher than those from the standard deviation of horizontal wind direction fluctuation. On the other hand, the ground deposition factors were shown to be same regardless of the classification method, as they were based on the graph obtained from empirical data presented in the Nuclear Regulatory Commission's Regulatory Guide 1.111, which is unrelated to the atmospheric stability for the ground level release. These results are based on the meteorological data collected over the course of one year at the specified sites; however, the classification method of atmospheric stability using the vertical temperature difference is expected to be more conservative.

  3. Plasma-Enhanced Chemical Vapor Deposition as a Method for the Deposition of Peptide Nanotubes

    Science.gov (United States)

    2013-09-17

    peptide nanotubes, plasma-enhanced chemical vapor deposition, nano assembly 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT SAR 18...Using physical vapor deposition ( PVD ) well-ordered assemblies of peptide nanotubes (PNTs) composed of dipeptide subunits are obtained on various...for the deposition of thin films (Figure 1b). A. B. Figure 1. (a) Illustration of physical vapor deposition ( PVD ) process of diphenylalanine

  4. Nonthermal Atmospheric Plasmas in Dental Restoration.

    Science.gov (United States)

    Liu, Y; Liu, Q; Yu, Q S; Wang, Y

    2016-05-01

    It is well known that the service life of contemporary composite restoration is unsatisfactory, and longevity of dentin bonding is one of the major culprits. Bonding is essentially a hybridization process in which dental substrate and adhesive resin interact with each other through an exchange process. Thus, the longevity of dentin bonding can only be improved with enhanced qualities in substrate, adhesive resin, and their interaction within the hybridization zone. This review aims to collect and summarize recent advances in utilizing nonthermal atmospheric plasmas (NTAPs)-a novel technology that delivers highly reactive species in a gaseous medium at or below physiologic temperature-to improve the durability of dentin bonding by addressing these 3 issues simultaneously. Overall, NTAP has demonstrated efficacies in improving a number of critical properties for dentin bonding, including deactivation of oral pathogens, modification of surface chemistry/properties, resin polymerization, improvement in adhesive-dentin interactions, and establishment of auxiliary bonding mechanism. While a few preliminary studies have indicated the benefit of NTAP to bond strength and stability, additional researches are warranted to employ knowledge acquired so far and to evaluate these properties in a systematic way.

  5. Nonthermal Atmospheric Plasmas in Dental Restoration

    Science.gov (United States)

    Liu, Y.; Liu, Q.; Yu, Q.S.; Wang, Y.

    2016-01-01

    It is well known that the service life of contemporary composite restoration is unsatisfactory, and longevity of dentin bonding is one of the major culprits. Bonding is essentially a hybridization process in which dental substrate and adhesive resin interact with each other through an exchange process. Thus, the longevity of dentin bonding can only be improved with enhanced qualities in substrate, adhesive resin, and their interaction within the hybridization zone. This review aims to collect and summarize recent advances in utilizing nonthermal atmospheric plasmas (NTAPs)—a novel technology that delivers highly reactive species in a gaseous medium at or below physiologic temperature—to improve the durability of dentin bonding by addressing these 3 issues simultaneously. Overall, NTAP has demonstrated efficacies in improving a number of critical properties for dentin bonding, including deactivation of oral pathogens, modification of surface chemistry/properties, resin polymerization, improvement in adhesive-dentin interactions, and establishment of auxiliary bonding mechanism. While a few preliminary studies have indicated the benefit of NTAP to bond strength and stability, additional researches are warranted to employ knowledge acquired so far and to evaluate these properties in a systematic way. PMID:26848068

  6. The atmospheric chemical vapour deposition of coatings on glass

    CERN Document Server

    Sanderson, K D

    1996-01-01

    The deposition of thin films of indium oxide, tin doped indium oxide (ITO) and titanium nitride for solar control applications have been investigated by Atmospheric Chemical Vapour Deposition (APCVD). Experimental details of the deposition system and the techniques used to characterise the films are presented. Results from investigations into the deposition parameters, the film microstructure and film material properties are discussed. A range of precursors were investigated for the deposition of indium oxide. The effect of pro-mixing the vaporised precursor with an oxidant source and the deposition temperature has been studied. Polycrystalline In sub 2 O sub 3 films with a resistivity of 1.1 - 3x10 sup - sup 3 OMEGA cm were obtained with ln(thd) sub 3 , oxygen and nitrogen. The growth of ITO films from ln(thd) sub 3 , oxygen and a range of tin dopants is also presented. The effect of the dopant precursor, the doping concentration, deposition temperature and the effect of additives on film growth and microstr...

  7. Plasma assisted deposition of metal fluorides for 193nm applications

    Science.gov (United States)

    Bischoff, Martin; Sode, Maik; Gaebler, Dieter; Kaiser, Norbert; Tuennermann, Andreas

    2008-10-01

    The ArF lithography technology requires a minimization of optical losses due to scattering and absorption. Consequently it is necessary to optimize the coating process of metal fluorides. The properties of metal fluoride thin films are mainly affected by the deposition methods, their parameters, and the vacuum conditions. Until now the best results were achieved by metal boat evaporation with high substrate temperature and without plasma assistance. In fact, it was demonstrated that the plasma assisted deposition process results in optical thin films with high packing density but the losses due to absorption were extremely high for deep and vacuum ultraviolet applications. This paper will demonstrate that most of the common metal fluorides can be deposited by electron beam evaporation with plasma assistance. In comparison to other deposition methods, the prepared thin films show low absorption in the VUV spectral range, high packing density, and less water content. The densification of the thin films was performed by a Leybold LION plasma source. As working gas, a variable mixture of fluorine and argon gas was chosen. To understand the deposition process and the interaction of the plasma with the deposition material, various characterization methods like plasma emission spectroscopy and ion current measurements were implemented.

  8. Atmospheric deposition of phosphorus to land and freshwater.

    Science.gov (United States)

    Tipping, E; Benham, S; Boyle, J F; Crow, P; Davies, J; Fischer, U; Guyatt, H; Helliwell, R; Jackson-Blake, L; Lawlor, A J; Monteith, D T; Rowe, E C; Toberman, H

    2014-07-01

    We compiled published and newly-obtained data on the directly-measured atmospheric deposition of total phosphorus (TP), filtered total phosphorus (FTP), and inorganic phosphorus (PO4-P) to open land, lakes, and marine coasts. The resulting global data base includes data for c. 250 sites, covering the period 1954 to 2012. Most (82%) of the measurement locations are in Europe and North America, with 44 in Africa, Asia, Oceania, and South-Central America. The deposition rates are log-normally distributed, and for the whole data set the geometric mean deposition rates are 0.027, 0.019 and 0.14 g m(-2) a(-1) for TP, FTP and PO4-P respectively. At smaller scales there is little systematic spatial variation, except for high deposition rates at some sites in Germany, likely due to local agricultural sources. In cases for which PO4-P was determined as well as one of the other forms of P, strong parallels between logarithmic values were found. Based on the directly-measured deposition rates to land, and published estimates of P deposition to the oceans, we estimate a total annual transfer of P to and from the atmosphere of 3.7 Tg. However, much of the phosphorus in larger particles (principally primary biological aerosol particles) is probably redeposited near to its origin, so that long-range transport, important for tropical forests, large areas of peatland and the oceans, mainly involves fine dust from deserts and soils, as described by the simulations of Mahowald et al. (Global Biogeochemical Cycles 22, GB4026, 2008). We suggest that local release to the atmosphere and subsequent deposition bring about a pseudo-diffusive redistribution of P in the landscape, with P-poor ecosystems, for example ombrotrophic peatlands and oligotrophic lakes, gaining at the expense of P-rich ones. Simple calculations suggest that atmospheric transport could bring about significant local redistribution of P among terrestrial ecosystems. Although most atmospherically transported P is natural

  9. Atmospheric Pressure Plasma Jet as a Dry Alternative to Inkjet Printing in Flexible Electronics

    Science.gov (United States)

    Gandhiraman, Ram Prasad; Lopez, Arlene; Koehne, Jessica; Meyyappan, M.

    2016-01-01

    We have developed an atmospheric pressure plasma jet printing system that works at room temperature to 50 deg C unlike conventional aerosol assisted techniques which require a high temperature sintering step to obtain desired thin films. Multiple jets can be configured to increase throughput or to deposit multiple materials, and the jet(s) can be moved across large areas using a x-y stage. The plasma jet has been used to deposit carbon nanotubes, graphene, silver nanowires, copper nanoparticles and other materials on substrates such as paper, cotton, plastic and thin metal foils.

  10. Deposition of Atmospheric Nitrogen Compounds in Humid Tropical Cuba

    Directory of Open Access Journals (Sweden)

    Osvaldo Cuesta-Santos

    2001-01-01

    Full Text Available Acid deposition, a direct effect of gaseous air pollutants, is causing widespread damage to terrestrial and aquatic ecosystems. Further, these pollutants are responsible for the corrosion of building materials and cultural objects, as well as having an impact on human health. In Cuba, main atmospheric deposition of nitrogen compounds varies from approximately 12.0 to 65.0 kg N ha�1 year�1 in rural areas. Ammonia and ammonium are the most important elements in Cuba�s tropical conditions.

  11. Deuterium Retention in the Co-Deposition Carbon Layers Deposited by Radio-Frequency Magnetron Sputtering in D2 Atmosphere

    Science.gov (United States)

    Zhang, Wei-Yuan; Shi, Li-Qun; Zhang, Bin; Hu, Jian-Sheng

    2014-05-01

    Carbon is deposited on C and Si substrates by rf magnetron plasma sputtering in a D2 atmosphere. The deposited layers are examined with ion beam analysis and thermal desorption spectroscopy (TDS). The growth rates of the layers deposited on Si decrease with increasing substrate temperature, while increase significantly with the increase of D2 pressure. Meanwhile, the deuterium concentrations in the layers deposited on the Si substrates decrease from 30% to 2% and from 31% to 1% on the C substrates, respectively, when the substrate temperature varies from 350K to 900 K. Similarly, the D concentration in the layer on the Si substrates increases from 3.4% to 47%, and from 8% to 35% on the C substrates when the D2 pressure increases from 0.3Pa to 8.0Pa. D desorption characterized by TDS is mainly in the forms of D2, HD, HDO, CD4, and C2D4, and a similar release peak occurs at 645 K. The release peak of D2 molecules at 960K can be attributed to the escaped gas from the thin co-deposited deuterium-rich carbon layer in the form of C-D bonding.

  12. Surface cleaning of metal wire by atmospheric pressure plasma

    Energy Technology Data Exchange (ETDEWEB)

    Nakamura, T., E-mail: tsubasa@oshima-k.ac.jp [Electronic-Mechanical Engineering Department, Oshima National College of Maritime Technology, 1091-1 Komatsu, Suo-Oshima, Yamaguchi (Japan); Department of Electrical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka (Japan); Buttapeng, C. [School of Electrical and Energy Engineering, University of the Thai Chamber of Commerce, 126/1, Vibhavadee-Rungsit, Dindaeng, Bangkok 10400 (Thailand); Furuya, S. [Faculty of Education, Gunma University, 4-2 Aramaki, Maebashi (Japan); Harada, N. [Department of Electrical Engineering, Nagaoka University of Technology, 1603-1 Kamitomioka, Nagaoka (Japan)

    2009-11-30

    In this study, the possible application of atmospheric pressure dielectric barrier discharge plasma for the annealing of metallic wire is examined and presented. The main purpose of the current study is to examine the surface cleaning effect for a cylindrical object by atmospheric pressure plasma. The experimental setup consists of a gas tank, plasma reactor, and power supply with control panel. The gas assists in the generation of plasma. Copper wire was used as an experimental cylindrical object. This copper wire was irradiated with the plasma, and the cleaning effect was confirmed. The result showed that it is possible to remove the tarnish which exists on the copper wire surface. The experiment reveals that atmospheric pressure plasma is usable for the surface cleaning of metal wire. However, it is necessary to examine the method for preventing oxidization of the copper wire.

  13. Effect of atmospheric electricity on dry deposition of airborne particles from atmosphere

    Science.gov (United States)

    Tammet, H.; Kimmel, V.; Israelsson, S.

    The electric mechanism of dry deposition is well known in the case of unattached radon daughter clusters that are unipolar charged and of high mobility. The problematic role of the electric forces in deposition of aerosol particles is theoretically examined by comparing the fluxes of particles carried by different deposition mechanisms in a model situation. The electric mechanism of deposition appears essential for particles of diameter 10-200 nm in conditions of low wind speed. The electric flux of fine particles can be dominant on the tips of leaves and needles even in a moderate atmospheric electric field of a few hundred V m -1 measured over the plane ground surface. The electric deposition is enhanced under thunderclouds and high voltage power lines. Strong wind suppresses the relative role of the electric deposition when compared with aerodynamic deposition. When compared with diffusion deposition the electric deposition appears less uniform: the precipitation particulate matter on the tips of leaves and especially on needles of top branches of conifer trees is much more intensive than on the ground surface and electrically shielded surfaces of plants. The knowledge of deposition geometry could improve our understanding of air pollution damage to plants.

  14. Biomedical applications and diagnostics of atmospheric pressure plasma

    Science.gov (United States)

    Petrović, Z. Lj; Puač, N.; Lazović, S.; Maletić, D.; Spasić, K.; Malović, G.

    2012-03-01

    Numerous applications of non-equilibrium (cold, low temperature) plasmas require those plasmas to operate at atmospheric pressure. Achieving non-equilibrium at atmospheric pressure is difficult since the ionization growth is very fast at such a high pressure. High degree of ionization on the other hand enables transfer of energy between electrons and ions and further heating of the background neutral gas through collisions between ions and neutrals. Thus, all schemes to produce non-equilibrium plasmas revolve around some form of control of ionization growth. Diagnostics of atmospheric pressure plasmas is difficult and some of the techniques cannot be employed at all. The difficulties stem mostly from the small size. Optical emission spectroscopy and laser absorption spectroscopy require very high resolution in order to resolve the anatomy of the discharges. Mass analysis is not normally applicable for atmospheric pressure plasmas, but recently systems with triple differential pumping have been developed that allow analysis of plasma chemistry at atmospheric pressures which is essential for numerous applications. Application of such systems is, however, not free from problems. Applications in biomedicine require minimum heating of the ambient air. The gas temperature should not exceed 40 °C to avoid thermal damage to the living tissues. Thus, plasmas should operate at very low powers and power control is essential. We developed unique derivative probes that allow control of power well below 1 W and studied four different sources, including dielectric barrier discharges, plasma needle, atmospheric pressure jet and micro atmospheric pressure jet. The jet operates in plasma bullet regime if proper conditions are met. Finally, we cover results on treatment of bacteria and human cells as well as treatment of plants by plasmas. Localized delivery of active species by plasmas may lead to a number of medical procedures that may also involve removal of bacteria, fungi and

  15. Asteroid fragmentation approaches for modeling atmospheric energy deposition

    Science.gov (United States)

    Register, Paul J.; Mathias, Donovan L.; Wheeler, Lorien F.

    2017-03-01

    During asteroid entry, energy is deposited in the atmosphere through thermal ablation and momentum-loss due to aerodynamic drag. Analytic models of asteroid entry and breakup physics are used to compute the energy deposition, which can then be compared against measured light curves and used to estimate ground damage due to airburst events. This work assesses and compares energy deposition results from four existing approaches to asteroid breakup modeling, and presents a new model that combines key elements of those approaches. The existing approaches considered include a liquid drop or "pancake" model where the object is treated as a single deforming body, and a set of discrete fragment models where the object breaks progressively into individual fragments. The new model incorporates both independent fragments and aggregate debris clouds to represent a broader range of fragmentation behaviors and reproduce more detailed light curve features. All five models are used to estimate the energy deposition rate versus altitude for the Chelyabinsk meteor impact, and results are compared with an observationally derived energy deposition curve. Comparisons show that four of the five approaches are able to match the overall observed energy deposition profile, but the features of the combined model are needed to better replicate both the primary and secondary peaks of the Chelyabinsk curve.

  16. INDUCTION PLASMA REACTIVE DEPOSITION OF TUNGSTENCARBIDE FROM TUNGSTEN METAL POWDER

    Institute of Scientific and Technical Information of China (English)

    X.L. Jiang; M.I. Boulos

    2001-01-01

    Experimental results are reported on the primary carburization reaction between the tungsten powder and methane in the induction plasma, and the secondary carburization of the deposit on substrate at high temperature. Optical microscopy and scanning electron microscopy were used to examine the microstructures of starting tungsten powder, carburized powder, and deposit. X-ray diffraction analysis, thermal gravimetric analysis and microhardness measurement were used to characterize the structures and properties of the powder and the deposit. It is found that the primary carburization reaction in the induction plasma starts from the surface of tungsten particles when the particles are melted. Tungsten particles are partially carburized inside the reactive plasma. Complete carburization is achieved through the secondary carburization reaction of the deposit on substrate at high temperature.``

  17. Plasma enhanced atomic layer deposition of silicon nitride using neopentasilane

    Energy Technology Data Exchange (ETDEWEB)

    Weeks, Stephen, E-mail: Stephen.Weeks@intermolecular.com; Nowling, Greg; Fuchigami, Nobi; Bowes, Michael; Littau, Karl [Intermolecular, 3011 North 1st Street, San Jose, California 95134 (United States)

    2016-01-15

    Progress in transistor scaling has increased the demands on the material properties of silicon nitride (SiN{sub x}) thin films used in device fabrication and at the same time placed stringent restrictions on the deposition conditions employed. Recently, low temperature plasma enhanced atomic layer deposition has emerged as a viable technique for depositing these films with a thermal budget compatible with semiconductor processing at sub-32 nm technology nodes. For these depositions, it is desirable to use precursors that are free from carbon and halogens that can incorporate into the film. Beyond this, it is necessary to develop processing schemes that minimize the wet etch rate of the film as it will be subjected to wet chemical processing in subsequent fabrication steps. In this work, the authors introduce low temperature deposition of SiN{sub x} using neopentasilane [NPS, (SiH{sub 3}){sub 4}Si] in a plasma enhanced atomic layer deposition process with a direct N{sub 2} plasma. The growth with NPS is compared to a more common precursor, trisilylamine [TSA, (SiH{sub 3}){sub 3 }N] at identical process conditions. The wet etch rates of the films deposited with NPS are characterized at different plasma conditions and the impact of ion energy is discussed.

  18. Hydrogen plasma treatment of silicon dioxide for improved silane deposition.

    Science.gov (United States)

    Gupta, Vipul; Madaan, Nitesh; Jensen, David S; Kunzler, Shawn C; Linford, Matthew R

    2013-03-19

    We describe a method for plasma cleaning silicon surfaces in a commercial tool that removes adventitious organic contamination and enhances silane deposition. As shown by wetting, ellipsometry, and XPS, hydrogen, oxygen, and argon plasmas effectively clean Si/SiO2 surfaces. However, only hydrogen plasmas appear to enhance subsequent low-pressure chemical vapor deposition of silanes. Chemical differences between the surfaces were confirmed via (i) deposition of two different silanes: octyldimethylmethoxysilane and butyldimethylmethoxysilane, as evidenced by spectroscopic ellipsometry and wetting, and (ii) a principal components analysis (PCA) of TOF-SIMS data taken from the different plasma-treated surfaces. AFM shows no increase in surface roughness after H2 or O2 plasma treatment of Si/SiO2. The effects of surface treatment with H2/O2 plasmas in different gas ratios, which should allow greater control of surface chemistry, and the duration of the H2 plasma (complete surface treatment appeared to take place quickly) are also presented. We believe that this work is significant because of the importance of silanes as surface functionalization reagents, and in particular because of the increasing importance of gas phase silane deposition.

  19. Oxygen Barrier Coating Deposited by Novel Plasma-enhanced Chemical Vapor Deposition

    DEFF Research Database (Denmark)

    Jiang, Juan; Benter, M.; Taboryski, Rafael Jozef

    2010-01-01

    We report the use of a novel plasma-enhanced chemical vapor deposition chamber with coaxial electrode geometry for the SiOx deposition. This novel plasma setup exploits the diffusion of electrons through the inner most electrode to the interior samples space as the major energy source. This confi......, and it increased the barrier property of the modified low-density polyethylene, polyethylene terephthalate, and polylactide by 96.48%, 99.69%, and 99.25%, respectively....

  20. Decomposition of Chemical Chain Molecules with Atmospheric Pressure Plasma

    Science.gov (United States)

    Tansli, Murat; Tasal, Erol

    2016-10-01

    Chemical chain molecules' decomposition is an interesting subject area for the atmospheric pressure plasma applications. The effects of the atmospheric pressure argon plasma on 4-((2-methoxyphenyl)Diazenyl)Benzene-1,3,-Diol molecule at room temperature are investigated. This molecule is one of the industrial dye molecules used widely. When considering the ecological life, this molecule will be very harmful and danger. We suggest a different, easy and useful decomposing method for such molecules. Atmospheric pressure plasma jet was principally treated for this decomposing of the molecule. Fourier transform infrared spectrometry (FT-IR) was used to characterization of the molecule after the plasma application to molecule in liquid phase with ethanol and methanol solvents. The atmospheric-pressure plasma jet of argon (Ar) as non-equilibrium has been formed by ac-power generator with frequency - 24 kHz and voltage - 12 kV. Characterizations for solutions prepared with ethanol and methanol solvents of molecule have been examined after applying (duration: 3 minutes) the atmospheric pressure plasma jet. The molecule was broken at 6C-7N =8N-9C stretching peak after the plasma treatment. The new plasma photo-products for ethanol and methanol solutions were produced as 6C-7N-8N =9C (strong, varying) and 12C =17O (strong, wide) stretching peaks.

  1. Nanoparticle formation and thin film deposition in aniline containing plasmas

    Science.gov (United States)

    Pattyn, Cedric; Dias, Ana; Hussain, Shahzad; Strunskus, Thomas; Stefanovic, Ilija; Boulmer-Leborgne, Chantal; Lecas, Thomas; Kovacevic, Eva; Berndt, Johannes

    2016-09-01

    This contribution deals with plasma based polymerization processes in mixtures of argon and aniline. The investigations are performed in a capacitively coupled RF discharge (in pulsed and continuous mode) and concern both the observed formation of nanoparticles in the plasma volume and the deposition of films. The latter process was used for the deposition of ultra-thin layers on different kind of nanocarbon materials (nanotubes and free standing graphene). The analysis of the plasma and the plasma chemistry (by means of mass spectroscopy and in-situ FTIR spectroscopy) is accompanied by several ex-situ diagnostics of the obtained materials which include NEXAFS and XPS measurements as well as Raman spectroscopy and electron microscopy. The decisive point of the investigations concern the preservation of the original monomer structure during the plasma polymerization processes and the stability of the thin films on the different substrates.

  2. Non-Thermal Sanitation By Atmospheric Pressure Plasma Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ORBITEC's Non-Thermal Sanitation by Atmospheric Pressure Plasma technology sanitizes fresh fruits and vegetables without the use of consumable chemicals and without...

  3. Plasma Extraction of Oxygen from Martian Atmosphere Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Plasma techniques are proposed for the extraction of oxygen from the abundant carbon dioxide contained in the Martian atmosphere (96 % CO2). In this process, CO2 is...

  4. Plasma Catalytic Extraction of Oxygen from the Martian Atmosphere Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Plasma catalytic techniques are proposed for the extraction of oxygen from the abundant carbon dioxide contained in the Martian atmosphere (95% CO2).. The Phase I...

  5. Non-Thermal Sanitation By Atmospheric Pressure Plasma Project

    Data.gov (United States)

    National Aeronautics and Space Administration — ORBITEC proposes to develop a non-thermal technology based on atmospheric-pressure (AP) cold plasma to sanitize foods, food packaging materials, and other hardware...

  6. Modeling Planetary Atmospheric Energy Deposition By Energetic Ions

    Science.gov (United States)

    Parkinson, Christopher; Bougher, Stephen; Gronoff, Guillaume; Barthelemy, Mathieu

    2016-07-01

    The structure, dynamics, chemistry, and evolution of planetary upper atmospheres are in large part determined by the available sources of energy. In addition to the solar EUV flux, the solar wind and solar energetic particle (SEP) events are also important sources. Both of these particle populations can significantly affect an atmosphere, causing atmospheric loss and driving chemical reactions. Attention has been paid to these sources from the standpoint of the radiation environment for humans and electronics, but little work has been done to evaluate their impact on planetary atmospheres. At unmagnetized planets or those with crustal field anomalies, in particular, the solar wind and SEPs of all energies have direct access to the atmosphere and so provide a more substantial energy source than at planets having protective global magnetic fields. Additionally, solar wind and energetic particle fluxes should be more significant for planets orbiting more active stars, such as is the case in the early history of the solar system for paleo-Venus and Mars. Therefore quantification of the atmospheric energy input from the solar wind and SEP events is an important component of our understanding of the processes that control their state and evolution. We have applied a full Lorentz motion particle transport model to study the effects of particle precipitation in the upper atmospheres of Mars and Venus. Such modeling has been previously done for Earth and Mars using a guiding center precipitation model. Currently, this code is only valid for particles with small gyroradii in strong uniform magnetic fields. There is a clear necessity for a Lorentz formulation, hence, a systematic study of the ionization, excitation, and energy deposition has been conducted, including a comparison of the influence relative to other energy sources (namely EUV photons). The result is a robust examination of the influence of energetic ion transport on the Venus and Mars upper atmosphere which

  7. Deposition of electrochromic tungsten oxide thin films by plasma-enhanced chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Henley, W.B.; Sacks, G.J. [Univ. of South Florida, Tampa, FL (United States). Center of Microelectronics

    1997-03-01

    Use of plasma-enhanced chemical vapor deposition (PECVD) for electrochromic WO{sub 3} film deposition is investigated. Oxygen, hydrogen, and tungsten hexafluoride were used as source gases. Reactant gas flow was investigated to determine the effect on film characteristics. High quality optical films were obtained at deposition rates on the order of 100 {angstrom}/s. Higher deposition rates were attainable but film quality and optical coherence degraded. Atomic emission spectroscopy (AES), was used to provide an in situ assessment of the plasma deposition chemistry. Through AES, it is shown that the hydrogen gas flow is essential to the deposition of the WO{sub 3} film. Oxygen gas flow and tungsten hexafluoride gas flow must be approximately equal for high quality films.

  8. A multifunctional plasma and deposition sensor for the characterization of plasma sources for film deposition and etching

    Science.gov (United States)

    Weise, Michael; Seeger, Stefan; Harbauer, Karsten; Welzel, Thomas; Ellmer, Klaus

    2017-07-01

    Our recently reported multifunctional plasma and deposition sensor [Welzel et al., Appl. Phys. Lett. 102, 211605 (2013)] was used for the characterization of two different plasma sources: a magnetron sputtering deposition source and an ion beam source. The multifunctional sensor, based on a conventional quartz crystal monitor (microbalance) for mass increase/decrease measurements, can measure quasi-simultaneously the deposition/etching flux, the energy flux, and the charged particle flux. By moving the sensor or the plasma source stepwise against each other, the lateral (radial) flux profiles of the different sources can be measured with a lateral resolution of about 8 mm, the diameter of aperture in front of the quartz crystal. It is demonstrated that this compact and simple multifunctional sensor is a versatile tool for the characterization of different kinds of plasma sources for deposition and etching purposes. By combining the different measured quantities, the ion-to-neutral ratio and the mean energy per deposited atom can be calculated, parameters that are essential for the characterization of plasma deposition and etch processes.

  9. Mechanisms controlling soil carbon sequestration under atmospheric nitrogen deposition

    Energy Technology Data Exchange (ETDEWEB)

    R.L. Sinsabaugh; D.R. Zak; D.L. Moorhead

    2008-02-19

    Increased atmospheric nitrogen (N) deposition can alter the processing and storage of organic carbon in soils. In 2000, we began studying the effects of simulated atmospheric N deposition on soil carbon dynamics in three types of northern temperate forest that occur across a wide geographic range in the Upper Great Lakes region. These ecosystems range from 100% oak in the overstory (black oak-white oak ecosystem; BOWO) to 0% overstory oak (sugar maple-basswood; SMBW) and include the sugar maple-red oak ecosystem (SMRO) that has intermediate oak abundance. The leaf litter biochemistry of these ecosystems range from highly lignified litter (BOWO) to litter of low lignin content (SMBW). We selected three replicate stands of each ecosystem type and established three plots in each stand. Each plot was randomly assigned one of three levels of N deposition (0, 30 & 80 kg N ha-1 y-1) imposed by adding NaNO3 in six equal increments applied over the growing season. Through experiments ranging from the molecular to the ecosystem scales, we produced a conceptual framework that describes the biogeochemistry of soil carbon storage in N-saturated ecosystems as the product of interactions between the composition of plant litter, the composition of the soil microbial community and the expression of extracellular enzyme activities. A key finding is that atmospheric N deposition can increase or decrease the soil C storage by modifying the expression of extracellular enzymes by soil microbial communities. The critical interactions within this conceptual framework have been incorporated into a new class of simulations called guild decomposition models.

  10. Atmospheric Deposition of Soluble Organic Nitrogen due to Biomass Burning

    Science.gov (United States)

    Ito, A.; Lin, G.; Penner, J. E.

    2014-12-01

    Atmospheric deposition of reactive nitrogen (N) species from large fires may contribute to enrichment of nutrients in aquatic ecosystems. Here we use an atmospheric chemistry transport model to investigate the supply of soluble organic nitrogen (ON) from open biomass burning to the ocean. The model results show that the annual deposition rate of soluble ON to the oceans is increased globally by 13% with the increase being particularly notable over the coastal water downwind from the source regions. The estimated deposition of soluble ON due to haze events from the secondary formation is more than half of that from the primary sources. We examine the secondary formation of particulate C-N compounds (e.g., imidazole) from the reactions of glyoxal and methylglyoxal with atmospheric ammonium in wet aerosols and upon cloud evaporation. These ON sources result in a significant contribution to the open ocean, suggesting that atmospheric processing in aqueous phase may have a large effect. We compare the soluble ON concentration in aerosols with and without open biomass burning as a case study in Singapore. The model results demonstrate that the soluble ON concentration in aerosols is episodically enriched during the fire events, compared to the without smoke simulations. However, the model results show that the daily soluble ON concentration can be also enhanced in the without smoke simulations during the same period, compared to the monthly averages. This indicates that care should be taken when using in-situ observations to constrain the soluble ON source strength from biomass burning. More accurate quantification of the soluble ON burdens with no smoke sources is therefore needed to assess the effect of biomass burning on bioavailable ON input to the oceans.

  11. Contribution of Atmospheric Nitrogen Compounds to N Deposition in a Broadleaf Forest of Southern China

    Institute of Scientific and Technical Information of China (English)

    HU Zheng-Yi; XU Cheng-Kai; ZHOU Li-Na; SUN Ben-Hua; HE Yuan-Qiu; ZHOU Jing; CAO Zhi-Hong

    2007-01-01

    A one-year study in a typical red soil region of southern China was conducted to determine atmospheric nitrogen (N) fluxes of typical N compounds (NH3, NH4-N, NO3-N, and NO2) and contribution of three sources (gas, rainwater, and particles) to N deposition. From July 2003 to June 2004, the total atmospheric N deposition was 70.7 kg N ha-1, with dry deposition accounting for 75% of the total deposition. Dry NH3 deposition accounted for 73% of the dry deposition and 55% of the total deposition. Moreover, NO2 contributed 11% of the dry deposition and 8% of the total deposition. Reduced N compounds (NH+4 and NH3) were the predominate contributors, accounting for 66% of the total deposition. Therefore, atmospheric N deposition should be considered when soil acidification and critical loads of atmospheric deposition on soils are estimated.

  12. Role of hydrogen diffusion in temperature-induced transformation of carbon nanostructures deposited on metallic substrates by using a specially designed fused hollow cathode cold atmospheric pressure plasma source

    Science.gov (United States)

    Sharma, Bikash; Kar, R.; Pal, Arup R.; Shilpa, R. K.; Dusane, R. O.; Patil, D. S.; Suryawanshi, S. R.; More, M. A.; Sinha, S.

    2017-04-01

    Carbon nanofibers (CNFs) and carbon nanotubes (CNTs) are grown on inconel substrates under two different experimental conditions using atmospheric pressure glow discharge radio-frequency (RF) PECVD process. A specially designed hollow cathode is used for this plasma generation. The growth is carried out at 610 and 660 °C substrate temperatures on inconel substrates. Our results show that CNFs and CNTs could be synthesized at 610 and 660 °C respectively irrespective of pre-treatment methods in either set. HRTEM results indicate that a temperature-induced transformation of CNFs into CNTs occur when the growth temperature is raised from 610 to 660 °C. With the help of characterization results and a schematic model, it is shown how an increase in hydrogen diffusion (~44% increase) plays a pivotal role in this transformation by providing a sink for hydrogen atoms. Field emission results show that most defective CNFs contribute to the maximum emission current density. This better field emission behavior is explained on the basis that the outer surfaces of CNFs are more defective due to the presence of the open edges of the graphene planes, which results in better field emission from the outer surfaces of the CNFs.

  13. Cellular membrane collapse by atmospheric-pressure plasma jet

    Science.gov (United States)

    Kim, Kangil; Jun Ahn, Hak; Lee, Jae-Hyeok; Kim, Jae-Ho; Sik Yang, Sang; Lee, Jong-Soo

    2014-01-01

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  14. Cellular membrane collapse by atmospheric-pressure plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kangil; Sik Yang, Sang, E-mail: jsjlee@ajou.ac.kr, E-mail: ssyang@ajou.ac.kr [Department of Electrical and Computer Engineering, Ajou University, Suwon 443-749 (Korea, Republic of); Jun Ahn, Hak; Lee, Jong-Soo, E-mail: jsjlee@ajou.ac.kr, E-mail: ssyang@ajou.ac.kr [Department of Biological Sciences, Ajou University, Suwon 443-749 (Korea, Republic of); Lee, Jae-Hyeok; Kim, Jae-Ho [Department of Molecular Science and Technology, Ajou University, Suwon 443-749 (Korea, Republic of)

    2014-01-06

    Cellular membrane dysfunction caused by air plasma in cancer cells has been studied to exploit atmospheric-pressure plasma jets for cancer therapy. Here, we report that plasma jet treatment of cervical cancer HeLa cells increased electrical conductivity across the cellular lipid membrane and caused simultaneous lipid oxidation and cellular membrane collapse. We made this finding by employing a self-manufactured microelectrode chip. Furthermore, increased roughness of the cellular lipid membrane and sequential collapse of the membrane were observed by atomic force microscopy following plasma jet treatment. These results suggest that the cellular membrane catastrophe occurs via coincident altered electrical conductivity, lipid oxidation, and membrane roughening caused by an atmospheric-pressure plasma jet, possibly resulting in cellular vulnerability to reactive species generated from the plasma as well as cytotoxicity to cancer cells.

  15. Delayed effects of cold atmospheric plasma on vascular cells

    NARCIS (Netherlands)

    Stoffels, Eva; Roks, Anton J. M.; Deelmm, Leo E.

    2008-01-01

    We investigated the long-term behaviour of vascular cells (endothelial and smooth muscle) after exposure to a cold atmospheric plasma source. The cells were treated through a gas-permeable membrane, in order to simulate intravenous treatment with a gas plasma-filled catheter. Such indirect treatment

  16. Delayed effects of cold atmospheric plasma on vascular cells

    NARCIS (Netherlands)

    Stoffels, Eva; Roks, Anton J. M.; Deelmm, Leo E.

    2008-01-01

    We investigated the long-term behaviour of vascular cells (endothelial and smooth muscle) after exposure to a cold atmospheric plasma source. The cells were treated through a gas-permeable membrane, in order to simulate intravenous treatment with a gas plasma-filled catheter. Such indirect treatment

  17. Spacecraft Sterilization Using Non-Equilibrium Atmospheric Pressure Plasma

    Science.gov (United States)

    Cooper, Moogega; Vaze, Nachiket; Anderson, Shawn; Fridman, Gregory; Vasilets, Victor N.; Gutsol, Alexander; Tsapin, Alexander; Fridman, Alexander

    2007-01-01

    As a solution to chemically and thermally destructive sterilization methods currently used for spacecraft, non-equilibrium atmospheric pressure plasmas are used to treat surfaces inoculated with Bacillus subtilis and Deinococcus radiodurans. Evidence of significant morphological changes and reduction in viability due to plasma exposure will be presented, including a 4-log reduction of B. subtilis after 2 minutes of dielectric barrier discharge treatment.

  18. Solid coatings deposited from liquid methyl methacrylate via Plasma Polymerization

    Science.gov (United States)

    Wurlitzer, Lisa; Maus-Friedrichs, Wolfgang; Dahle, Sebastian

    2016-09-01

    The polymerization of methyl methacrylate via plasma discharges is well known today. Usually, plasma-enhanced chemical vapor deposition (PECVD) is used to deposit polymer coatings. Solid coatings are formed out of the liquid phase from methyl methacrylate via dielectric barrier discharge. The formation of the coating proceeds in the gas and the liquid phase. To learn more about the reactions in the two phases, the coatings from MMA monomer will be compared to those from MMA resin. Finally, attenuated total reflection infrared spectroscopy, confocal laser scanning microscopy and X-ray photoelectron spectroscopy are employed to characterize the solid coatings. In conclusion, the plasma enhanced chemical solution deposition is compared to the classical thermal polymerization of MMA.

  19. Open air plasma deposited antimicrobial SiOx/TiOx composite films for biomedical applications

    Directory of Open Access Journals (Sweden)

    Rapp Christin

    2016-09-01

    Full Text Available Open air atmospheric pressure plasma jet (APPJ enhanced chemical vapour deposition process was used to deposit biocompatible SiOx/TiOx composite coatings. The as deposited films are hydrophilic and show visible light induced photocatalytic effect, which is a consequence of the formation of defects in the TiOx structure due to the plasma process. This photocatalytic effect was verified by the demonstration of an antimicrobial effect under visible light on E. coli as well as by degradation of Rhodamine B. The films are non-cytotoxic as shown by the cytocompatibility tests. The films are conductive to cell growth and are stable in DMEM and isopropanol. The structural evaluation using SEM, EDS and XPS shows a dispersion of TiOx phase in a SiOxCyHz matrix. These analyses were used to correlate the structure-property relationship of the composite coating.

  20. Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

    Energy Technology Data Exchange (ETDEWEB)

    Kan, C.W., E-mail: tccwk@polyu.edu.hk [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Kwong, C.H. [Institute of Textiles and Clothing, The Hong Kong Polytechnic University, Hung Hom, Kowloon (Hong Kong); Ng, S.P. [Hong Kong Community College, The Hong Kong Polytechnic University (Hong Kong)

    2015-08-15

    Highlights: • Atmospheric pressure plasma treatment improved surface performance of polyester synthetic leather with tetramethylsilane. • XPS and FTIR confirmed the deposition of organosilanes on the sample's surface. • Contact angle increases to 138° after plasma treatment. - Abstract: Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

  1. Single channel atmospheric pressure transporting plasma and plasma stream demultiplexing: physical characterization and application to E. coli bacteria inactivation

    Science.gov (United States)

    Valinataj Omran, A.; Sohbatzadeh, F.; Siadati, S. N.; Hosseinzadeh Colagar, A.; Akishev, Y.; Arefi-Khonsari, F.

    2017-08-01

    In this article, we developed transporting plasma sources that operate at atmospheric pressure. The effect of electrode configuration on plasma transporting was investigated. In order to increase the transporting plasma cross-section, we converted a plasma stream into four plasma channels by a cylindrical housing. Electron excitation and rotational temperatures were estimated using optical emission spectroscopy. Furthermore, the electrical and temporal characteristics of the plasma, discharge power and charge deposition on the target were investigated. The propagation characteristics of single and multi-channel transporting plasma were compared with the same cross-sectional area. Two configurations for multi-channels were designed for this purpose. Escherichia coli bacteria were exposed to the single and multi-channel transporting discharge for different time durations. After exposure, the results indicated that the inactivation zones were significantly increased by a multi-channel transporting plasma. Finally, E. coli inactivation by those plasma apparatuses was compared with that of several standard antimicrobial test discs such as Gentamicin, Tetracycline, Amoxicillin and Cefixime.

  2. Atmospheric Deposition of Copper and Zinc in Maramures County (Romania

    Directory of Open Access Journals (Sweden)

    Buteana Claudia

    2014-12-01

    Full Text Available The need to reduce pollution to levels that minimize adverse effects on human health involve the monitoring of air quality, including dry depositions and their metal content. The analysis of these parameters aims to investigate the air quality in Maramures County (with nonferrous mining activities and in the Romanian - Ukraine transboundary area. The paper presents the experimental results obtained for dry atmospheric deposition of copper and zinc using flame atomic absorption spectrometry (FAAS. The samples were collected from four location/cities of Maramures County (Baia Mare, Sighetu Marmatiei, Viseu de Sus and Borsa during May-October 2014. The highest average values of copper concentration in the dry depositions were found in Baia Mare (199.88 μg/g, that is the most important industrial centre in Maramures County, followed by Borsa (111.49 μg/g, that used to be a nonferrous mining centre. In Viseu de Sus and Sighetu Marmatiei the average concentrations of copper in the dry depositions were lower: 75.63 μg/g and 64.26 μg/g, respectively. Zn average concentrations in dry depositions were 6.4-12 times higher than Cu concentrations. In Viseu de Sus and Borsa relative high values of Pearson correlation coefficients between the logarithm of Cu and Zn content in the dry deposition were found (0.702 and 0.737, respectively estimating that both pollutants in the ambient air have the same sources, probably the re-suspension of the dust from the tailing ponds. This study is implemented within the frame of ENPI Cross-border Cooperation Programme Hungary-Slovakia-Romania-Ukraine 2007-2013, in the project Clean Air Management in the Romania-Ukraine Transboundary Area - (CLAMROUA, financed by the European Union

  3. Experimental approaches for studying non-equilibrium atmospheric plasma jets

    Energy Technology Data Exchange (ETDEWEB)

    Shashurin, A., E-mail: ashashur@purdue.edu [School of Aeronautics & Astronautics, Purdue University, West Lafayette, Indiana 47907 (United States); Keidar, M. [Department of Mechanical and Aerospace Engineering, The George Washington University, Washington, District of Columbia 20052 (United States)

    2015-12-15

    This work reviews recent research efforts undertaken in the area non-equilibrium atmospheric plasma jets with special focus on experimental approaches. Physics of small non-equilibrium atmospheric plasma jets operating in kHz frequency range at powers around few Watts will be analyzed, including mechanism of breakdown, process of ionization front propagation, electrical coupling of the ionization front with the discharge electrodes, distributions of excited and ionized species, discharge current spreading, transient dynamics of various plasma parameters, etc. Experimental diagnostic approaches utilized in the field will be considered, including Rayleigh microwave scattering, Thomson laser scattering, electrostatic streamer scatterers, optical emission spectroscopy, fast photographing, etc.

  4. Microbial release of sulphur ions from atmospheric pollution deposits

    Energy Technology Data Exchange (ETDEWEB)

    Killhan, K.; Wainwright, M.

    1981-12-01

    The surfaces of leaves of Acer pseudoplatanus growing in areas exposed to heavy atmospheric pollution are covered with atmospheric pollution deposits (APD). Using scanning electron microscopy, micro-organisms were seen to be growing in intimate association with these deposits. The deposits contained sufficient carbon and nitrogen to support growth of the fungus Fusarium solani in culture and in autoclaved and non-sterilized soils; and sufficient reduced sulphur for the in vitro growth of Thiobacillus thioparus. When T. thioparus and F. solani were grown in medium supplemented with APD as sole carbon and nitrogen sources, increases in the concentrations of soluble S/sub 2/O/sup 2 -//sub 3/; S/sub 4/O/sup 2 -//sub 6/ and SO/sup 2 -//sub 4/ resulted. Similar increases also occurred when APD was added to complete fungal growth medium. Increases in LiCl/sub 2/-extractable sulphur-ions also occurred in fresh soil amended with APD, and in autoclaved soils containing APD, and inoculated with spores of F. solani. Arylsulphatase activity increased in fresh soils and in soils autoclaved and inoculated with F. solani when APD was added; suggesting sulphur mineralization, as well as sulphur oxidation, in the release of sulphur ions from APD. We concluded that APD can support microbial growth in vitro and in soils when provided as sole carbon and sulphur source; and that micro-organisms can release sulphur ions from this complex substrate. Microbial release of sulphur ions from APD can account in part for the increased concentrations of sulphur ions in heavy atmospheric-polluted soils.

  5. Microbial release of sulphur ions from atmospheric pollution deposits

    Energy Technology Data Exchange (ETDEWEB)

    Killham, K.; Wainwright, M.

    1981-12-01

    The surface of leaves of Acer pseudoplatanus growing in areas exposed to heavy atmospheric pollution are covered with atmospheric pollution deposits (APD). Using scanning electric microscopy, micro-organisms were seen to be growing in intimate association with these deposits. The deposits contained sufficient carbon and nitrogen to support growth of the fungus Fusarium solani in culture and in autoclaved and non-sterilized soils; and sufficient reduced sulphur for in vitro growth of Thiobacillus thioparus. When T. thioparus and F. solani were grown in medium supplemented with APD as sole carbon and nitrogen sources, increases in the concentrations of soluble S/sub 2/O/sub 3//sup 2/ btw/sup -/ and; S/sub 4/O/sub 6//sup 2 -/ and SO/sub 4//sup 2 -/ resulted. Similar increases also occurred when APD was added to complete fungal growth medium. Increases in LiCl/sub 2/-extractable sulphur-ions also occurred is fresh soil amended with APD, and in autoclaved soils containing APD, and inoculated with spores of F. solani. Arylsulphatase activity increased in fresh soils and in soils autoclaved and inoculated with F. solani when APD was added; suggesting sulphur mineralization, as well as sulphur oxidation, in the release of sulphur ions from APD. We conclude that APD can support microbial growth in vitro and in soils when provided as sole carbon and sulphur source; and that micro-organisms can release sulphur ions from this complex substrate. Microbial release of sulphur ions from APD can account in part for the increased concentrations of sulphur ions in heavy atmospheric-polluted soils.

  6. Spatial variation in atmospheric nitrogen deposition on low canopy vegetation

    Energy Technology Data Exchange (ETDEWEB)

    Verhagen, Rene [Community and Conservation Ecology Group, University of Groningen, P.O. Box 14, 9750 AA Haren (Netherlands); Diggelen, Rudy van [Community and Conservation Ecology Group, University of Groningen, P.O. Box 14, 9750 AA Haren (Netherlands)]. E-mail: r.van.diggelen@rug.nl

    2006-12-15

    Current knowledge about the spatial variation of atmospheric nitrogen deposition on a local scale is limited, especially for vegetation with a low canopy. We measured nitrogen deposition on artificial vegetation at variable distances of local nitrogen emitting sources in three nature reserves in the Netherlands, differing in the intensity of agricultural practices in the surroundings. In the nature reserve located in the most intensive agricultural region nitrogen deposition decreased with increasing distance to the local farms, until at a distance of 1500 m from the local nitrogen emitting sources the background level of 15 kg N ha{sup -1} yr{sup -1} was reached. No such trend was observed in the other two reserves. Interception was considerably lower than in woodlands and hence affected areas were larger. The results are discussed in relation to the prospects for the conservation or restoration of endangered vegetation types of nutrient-poor soil conditions. - Areas with low canopy vegetation are affected over much larger distances by nitrogen deposition than woodlands.

  7. Atmospheric deposition of fluoride in the lower Tamar Valley, Tasmania

    Science.gov (United States)

    Low, P. S.; Bloom, H.

    Soluble fluoride (F -), measured using an ion-selective electrode, was monitored during 1982-1983 in monthly bulk (wet and dry) atmospheric deposition samples collected at 17 locations in the lower Tamar Valley, Tasmania, where an aluminium (Al) smelter is located. Glass samplers (funnel-bottle type) were used, with duplications by plastic samplers at five locations later. The spatial and temporal variations in F - deposition in relation to wind flow and rainfall are discussed, and its impact on the environment is highlighted. The mean deposition rates of F -, as measured from September 1982 to August 1983, ranged from about 90 μg m -2 day -1 at the intended 'background' location to 12,568 μg m -2day -1 at a location about 1 km east-southeast from the smelter. The depositional fluxes of F - and insoluble Al (another elemental tracer of the smelter) are significantly correlated ( P plastic samplers collected about 8 and 17% more F - and Al, respectively, but with higher standard deviations. Thus the variations observed could be largely due to sampling fluctuations.

  8. Response of global soil consumption of atmospheric methane to changes in atmospheric climate and nitrogen deposition

    Science.gov (United States)

    Zhuang, Qianlai; Chen, Min; Xu, Kai; Tang, Jinyun; Saikawa, Eri; Lu, Yanyu; Melillo, Jerry M.; Prinn, Ronald G.; McGuire, A. David

    2013-01-01

    Soil consumption of atmospheric methane plays an important secondary role in regulating the atmospheric CH4 budget, next to the dominant loss mechanism involving reaction with the hydroxyl radical (OH). Here we used a process-based biogeochemistry model to quantify soil consumption during the 20th and 21st centuries. We estimated that global soils consumed 32–36 Tg CH4 yr−1 during the 1990s. Natural ecosystems accounted for 84% of the total consumption, and agricultural ecosystems only consumed 5 Tg CH4 yr−1 in our estimations. During the twentieth century, the consumption rates increased at 0.03–0.20 Tg CH4 yr−2 with seasonal amplitudes increasing from 1.44 to 3.13 Tg CH4 month−1. Deserts, shrublands, and xeric woodlands were the largest sinks. Atmospheric CH4 concentrations and soil moisture exerted significant effects on the soil consumption while nitrogen deposition had a moderate effect. During the 21st century, the consumption is predicted to increase at 0.05-1.0 Tg CH4 yr−2, and total consumption will reach 45–140 Tg CH4 yr−1 at the end of the 2090s, varying under different future climate scenarios. Dry areas will persist as sinks, boreal ecosystems will become stronger sinks, mainly due to increasing soil temperatures. Nitrogen deposition will modestly reduce the future sink strength at the global scale. When we incorporated the estimated global soil consumption into our chemical transport model simulations, we found that nitrogen deposition suppressed the total methane sink by 26 Tg during the period 1998–2004, resulting in 6.6 ppb higher atmospheric CH4 mixing ratios compared to without considering nitrogen deposition effects. On average, a cumulative increase of every 1 Tg soil CH4 consumption decreased atmospheric CH4 mixing ratios by 0.26 ppb during the period 1998–2004.

  9. Seed disinfection effect of atmospheric pressure plasma and low pressure plasma on Rhizoctonia solani.

    Science.gov (United States)

    Nishioka, Terumi; Takai, Yuichiro; Kawaradani, Mitsuo; Okada, Kiyotsugu; Tanimoto, Hideo; Misawa, Tatsuya; Kusakari, Shinichi

    2014-01-01

    Gas plasma generated and applied under two different systems, atmospheric pressure plasma and low pressure plasma, was used to investigate the inactivation efficacy on the seedborne pathogenic fungus, Rhizoctonia solani, which had been artificially introduced to brassicaceous seeds. Treatment with atmospheric plasma for 10 min markedly reduced the R. solani survival rate from 100% to 3% but delayed seed germination. The low pressure plasma treatment reduced the fungal survival rate from 83% to 1.7% after 10 min and the inactivation effect was dependent on the treatment time. The seed germination rate after treatment with the low pressure plasma was not significantly different from that of untreated seeds. The air temperature around the seeds in the low pressure system was lower than that of the atmospheric system. These results suggested that gas plasma treatment under low pressure could be effective in disinfecting the seeds without damaging them.

  10. Microwave plasma deposition of diamond like carbon coatings

    Science.gov (United States)

    Patil, D. S.; Ramachandran, K.; Venkataramani, N.; Pandey, M.; D'Cunha, R.

    2000-11-01

    he promising applications of the microwave plasmas have been appearing in the fields of chemical processes and semiconductor manufacturing. Applications include surface deposition of all types including diamond/diamond like carbon (DLC) coatings, etching of semiconductors, promotion of organic reactions, etching of polymers to improve bonding of the other materials etc. With a 2.45 GHz, 700 W, microwave induced plasma chemical vapor deposition (CVD) system set up in our laboratory we have deposited diamond like carbon coatings. The microwave plasma generation was effected using a wave guide single mode applicator. We have deposited DLC coatings on the substrates like stainless steel, Cu--Be, Cu and Si. The deposited coatings have been characterized by FTIR, Raman spectroscopy and ellipsometric techniques. The results show that we have achieved depositing ~ 95% sp3 bonded carbon in the films. The films are uniform with golden yellow color. The films are found to be excellent insulators. The ellipsometric measurements of optical constant on silicon substrates indicate that the films are transparent above 900 nm.

  11. Mercury in the global atmosphere: Chemistry, deposition, and land-atmosphere interactions

    Science.gov (United States)

    Selin, Noelle Eckley

    This thesis uses a global 3-D chemical transport model (GEOS-Chem), in conjunction with worldwide atmospheric observations, to better understand and quantify biogeochemical cycling and deposition of mercury. GEOS-Chem includes gaseous elemental (Hg(0)), divalent (Hg(II)), and particulate (Hg(P)) mercury in the atmosphere, and includes coupling with the ocean, developed at University of Washington, and with land, developed in this work. Observed concentrations and seasonal variation of total gaseous mercury (TGM) are consistent with photochemical oxidation for Hg(0) partly balanced by in-cloud photochemical reduction of Hg(II). High TGM concentrations from ship cruises in the Northern Hemisphere are not reproduced, implying a problem either in measurements or our understanding of sources. Model results, supported by observations, suggest Hg(II) to be dominant at higher altitudes. Diurnal variability observed at marine sites suggests uptake by sea salt aerosols is a major deposition mechanism. Global biogeochemical cycles of mercury are constructed for pre-industrial and present-day using the first fully-coupled, global 3-D land-atmosphere-ocean mercury model. Atmosphere-surface cycling increases the effective mercury lifetime more than threefold against transfer to long-lived soil and ocean reservoirs. It is estimated that 68% of deposition to the U.S. is anthropogenic, including 16% from the legacy of anthropogenic mercury accumulated in soils and the deep ocean. Observed seasonal variations in U.S. wet deposition are used to constrain redox and deposition processes influencing the fate of North American and international emissions. The model reproduces the seasonal variation and latitudinal gradient of wet deposition flux measured in the eastern U.S., with a maximum in the Southeast and higher fluxes in summer and at lower latitudes. Seasonal variation is attributed to variations in oxidation and wet deposition rates at northern latitudes, and to seasonal

  12. Rapid Deposition of Titanium Oxide and Zinc Oxide Films by Solution Precursor Plasma Spray

    Science.gov (United States)

    Ando, Yasutaka

    In order to develop a high rate atmospheric film deposition process for functional films, as a basic study, deposition of titanium oxide film and zinc oxide film by solution precursor plasma spray (SPPS) was conducted in open air. Consequently, in the case of titanium oxide film deposition, anantase film and amorphous film as well as rutile film could be deposited by varying the deposition distance. In the case of anatase dominant film, photo-catalytic properties of the films could be confirmed by wettability test. In addition, the dye sensitized sollar cell (DSC) using the TiO2 film deposited by this SPPS technique as photo voltaic device generates 49mV in OCV. On the other hand, in the case of zinc oxide film deposition, it was proved that well crystallized ZnO films with photo catalytic properties could be deposited. From these results, this process was found to have high potential for high rate functional film deposition process conducted in the air.

  13. Ultrasound enhanced plasma surface modification at atmospheric pressure

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Singh, Shailendra Vikram; Norrman, Kion

    Atmospheric pressure plasma treatment can be highly enhanced by simultaneous high-power ultrasonic irradiation onto the treating surface. It is because ultrasonic waves with a sound pressure level (SPL) above approximately 140 dB can reduce the thickness of a boundary gas layer between the plasma...... and the material surface, and thus many reactive species generated in the plasma can reach the surface before inactivated, and be efficiently utilized for surface modification. In the present work polyester plates are treated using a dielectric barrier discharge (DBD) and a gliding arc at atmospheric pressure...... irradiation, the water contact angle dropped markedly, and tended to decrease furthermore at higher power. The ultrasonic irradiation during the plasma treatment consistently improved the wettability. Oxygen containing polar functional groups were introduced at the surface by the plasma treatment...

  14. Very high frequency plasma reactant for atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Il-Kwon; Yoo, Gilsang; Yoon, Chang Mo [School of Electrical and Electronic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Kim, Tae Hyung; Yeom, Geun Young [Department of Advanced Materials Engineering, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of); Kim, Kangsik; Lee, Zonghoon [School Materials Science and Engineering, Ulsan National Institute of Science and Technology (UNIST), Ulsan 44919 (Korea, Republic of); Jung, Hanearl; Lee, Chang Wan [School of Electrical and Electronic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Kim, Hyungjun, E-mail: hyungjun@yonsei.ac.kr [School of Electrical and Electronic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Lee, Han-Bo-Ram, E-mail: hbrlee@inu.ac.kr [Department of Materials Science and Engineering, Incheon National University, 406-840 Incheon (Korea, Republic of)

    2016-11-30

    Highlights: • Fundamental research plasma process for thin film deposition is presented. • VHF plasma source for PE-ALD Al{sub 2}O{sub 3} was employed to reduce plasma damage. • The use of VHF plasma improved all of the film qualities and growth characteristics. - Abstract: Although plasma-enhanced atomic layer deposition (PE-ALD) results in several benefits in the formation of high-k dielectrics, including a low processing temperature and improved film properties compared to conventional thermal ALD, energetic radicals and ions in the plasma cause damage to layer stacks, leading to the deterioration of electrical properties. In this study, the growth characteristics and film properties of PE-ALD Al{sub 2}O{sub 3} were investigated using a very-high-frequency (VHF) plasma reactant. Because VHF plasma features a lower electron temperature and higher plasma density than conventional radio frequency (RF) plasma, it has a larger number of less energetic reaction species, such as radicals and ions. VHF PE-ALD Al{sub 2}O{sub 3} shows superior physical and electrical properties over RF PE-ALD Al{sub 2}O{sub 3}, including high growth per cycle, excellent conformality, low roughness, high dielectric constant, low leakage current, and low interface trap density. In addition, interlayer-free Al{sub 2}O{sub 3} on Si was achieved in VHF PE-ALD via a significant reduction in plasma damage. VHF PE-ALD will be an essential process to realize nanoscale devices that require precise control of interfaces and electrical properties.

  15. Atmospheric Electrodeless Microwave Plasma-torch for Gas Decomposition

    Science.gov (United States)

    Kim, J. H.; Hong, Y. C.; Uhm, H. S.

    2001-10-01

    Increasing environmental awareness and regulation have motivated research into new method to remediate toxins from atmospheric pressure gas streams. Plasma remediation was identified as a promising technology treating contaminated gas streams and air. Plasma remediation of toxic gas streams from mobile emitting sources (i. e., Nox, Sox, soot emission from diesel truck engines) and cleaning processes (i.e., global warming gases) require inexpensive, compact, and reliable systems which efficiently and selectively convert the toxic gas to benign or more treatable products. Environmental clean-up and energy efficiency enhancement utilize plasma generated from air at the atmospheric pressure. Electrodes of the arc plasma torches oxidize very quickly due to the oxygen molecules in air. That is why the conventional thermal plasma torch can not be used in environmental applications. In order to solve this difficult problem, we developed a thermal plasma source operating without electrodes. One of electrodeless torches is the microwave plasma which can produce plasmas in large quantities. We can generate plasma at the atmospheric pressure by making use of magnetrons in microwave-ovens. Most of the magnetrons are operated at the frequency of 2.45GHz. Typical magnetron power of home-microwave oven is about 1kW. Electromagnetic waves from magnetron propagate through a waveguide. Plasma is generated under resonant condition, by initiation of an auxiliary ignition system. The plasma is stabilized by vortex stabilization. The eventual application of this research is in air pollution control. Perfluorocarbon Compounds(PFCs), , , and any other global warming gases from etching and cleaning processes have very long lifetime and high global warming potential. We will conduct an experiment to eliminate global warming gases. FT-IR and QMS will be used to analyze and identify by-products after plasma treatment.

  16. The technology of Plasma Spray Physical Vapour Deposition

    Directory of Open Access Journals (Sweden)

    M. Góral

    2012-12-01

    Full Text Available Purpose: The deposition of thermal barrier coatings is currently the most effective means of protecting the surface of aircraft engine turbine blades from the impact of aggressive environment of combustion gases. The new technologies of TBC depositions are required.Design/methodology/approach: The essential properties of the PS-PVD process have been outlined, as well as recent literature references. In addition, the influence of a set process condition on the properties of the deposited coatings has been described.Findings: The new plasma-spraying PS-PVD method is a promising technology for the deposition of modern thermal barrier coatings on aircraft engine turbine blades.Research limitations/implications: The constant progress of engine operating temperatures and increasing pollution restrictions determine the intensive development of heat-resistant coatings, which is directed to new deposition technologies and coating materials.Practical implications: The article presents a new technology of thermal barrier coating deposition - LPPS Thin Film and Plasma Spray - Physical Vapour Deposition.Originality/value: The completely new technologies was described in article.

  17. Parameters of atmospheric plasmas produced by electrosurgical devices

    Science.gov (United States)

    Keidar, Michael; Shashurin, Alexey; Canady, Jerome

    2013-10-01

    Electrosurgical systems are extensively utilized in general surgery, surgical oncology, plastic and reconstructive surgery etc. In this work we study plasma parameters created by electrosurgical system SS-200E/Argon 2 of US Medical Innovations. The maximal length of the discharge plasma column at which the discharge can be sustained was determined as function of discharge power and argon flow rate. Electrical parameters including discharge current and voltage were measured. Recently proposed Rayleigh microwave scattering method for temporally resolved density measurements of small-size atmospheric plasmas was utilized. Simultaneously, evolution of plasma column was observed using intensified charge-coupled device (ICCD) camera.

  18. Plasma deposition of silver nanoparticles on ultrafiltration membranes: antibacterial and anti-biofouling properties.

    Science.gov (United States)

    Cruz, Mercedes Cecilia; Ruano, Gustavo; Wolf, Marcus; Hecker, Dominic; Vidaurre, Elza Castro; Schmittgens, Ralph; Rajal, Verónica Beatriz

    2015-02-01

    A novel and versatile plasma reactor was used to modify Polyethersulphone commercial membranes. The equipment was applied to: i) functionalize the membranes with low-temperature plasmas, ii) deposit a film of poly(methyl methacrylate) (PMMA) by Plasma Enhanced Chemical Vapor Deposition (PECVD) and, iii) deposit silver nanoparticles (SNP) by Gas Flow Sputtering. Each modification process was performed in the same reactor consecutively, without exposure of the membranes to atmospheric air. Scanning electron microscopy and transmission electron microscopy were used to characterize the particles and modified membranes. SNP are evenly distributed on the membrane surface. Particle fixation and transport inside membranes were assessed before- and after-washing assays by X-ray photoelectron spectroscopy depth profiling analysis. PMMA addition improved SNP fixation. Plasma-treated membranes showed higher hydrophilicity. Anti-biofouling activity was successfully achieved against Gram-positive (Enterococcus faecalis) and -negative (Salmonella Typhimurium) bacteria. Therefore, disinfection by ultrafiltration showed substantial resistance to biofouling. The post-synthesis functionalization process developed provides a more efficient fabrication route for anti-biofouling and anti-bacterial membranes used in the water treatment field. To the best of our knowledge, this is the first report of a gas phase condensation process combined with a PECVD procedure in order to deposit SNP on commercial membranes to inhibit biofouling formation.

  19. Plasma deposition of silver nanoparticles on ultrafiltration membranes: antibacterial and anti-biofouling properties

    Science.gov (United States)

    Cruz, Mercedes Cecilia; Ruano, Gustavo; Wolf, Marcus; Hecker, Dominic; Vidaurre, Elza Castro; Schmittgens, Ralph; Rajal, Verónica Beatriz

    2015-01-01

    A novel and versatile plasma reactor was used to modify Polyethersulphone commercial membranes. The equipment was applied to: i) functionalize the membranes with low-temperature plasmas, ii) deposit a film of poly(methyl methacrylate) (PMMA) by Plasma Enhanced Chemical Vapor Deposition (PECVD) and, iii) deposit silver nanoparticles (SNP) by Gas Flow Sputtering. Each modification process was performed in the same reactor consecutively, without exposure of the membranes to atmospheric air. Scanning electron microscopy and transmission electron microscopy were used to characterize the particles and modified membranes. SNP are evenly distributed on the membrane surface. Particle fixation and transport inside membranes were assessed before- and after-washing assays by X-ray photoelectron spectroscopy depth profiling analysis. PMMA addition improved SNP fixation. Plasma-treated membranes showed higher hydrophilicity. Anti-biofouling activity was successfully achieved against Gram-positive (Enterococcus faecalis) and -negative (Salmonella Typhimurium) bacteria. Therefore, disinfection by ultrafiltration showed substantial resistance to biofouling. The post-synthesis functionalization process developed provides a more efficient fabrication route for anti-biofouling and anti-bacterial membranes used in the water treatment field. To the best of our knowledge, this is the first report of a gas phase condensation process combined with a PECVD procedure in order to deposit SNP on commercial membranes to inhibit biofouling formation. PMID:26166926

  20. Surface modification of polyester synthetic leather with tetramethylsilane by atmospheric pressure plasma

    Science.gov (United States)

    Kan, C. W.; Kwong, C. H.; Ng, S. P.

    2015-08-01

    Much works have been done on synthetic materials but scarcely on synthetic leather owing to its surface structures in terms of porosity and roughness. This paper examines the use of atmospheric pressure plasma (APP) treatment for improving the surface performance of polyester synthetic leather by use of a precursor, tetramethylsilane (TMS). Plasma deposition is regarded as an effective, simple and single-step method with low pollution. Scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR) confirm the deposition of organosilanes on the sample's surface. The results showed that under a particular combination of treatment parameters, a hydrophobic surface was achieved on the APP treated sample with sessile drop static contact angle of 138°. The hydrophobic surface is stable without hydrophilic recovery 30 days after plasma treatment.

  1. Plasma-Powder Feedstock Interaction During Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Hongbo; Zhang, Baopeng

    2017-02-01

    Plasma spray-physical vapor deposition is a new process developed to produce coatings from the vapor phase. To achieve deposition from the vapor phase, the plasma-feedstock interaction inside the plasma torch, i.e., from the powder injection point to the nozzle exit, is critical. In this work, the plasma characteristics and the momentum and heat transfer between the plasma and powder feedstock at different torch input power levels were investigated theoretically to optimize the net plasma torch power, among other important factors such as the plasma gas composition, powder feed rate, and carrier gas. The plasma characteristics were calculated using the CEA2 code, and the plasma-feedstock interaction was studied inside the torch nozzle at low-pressure (20-25 kPa) conditions. A particle dynamics model was introduced to compute the particle velocity, coupled with Xi Chen's drag model for nonevaporating particles. The results show that the energy transferred to the particles and the coating morphology are greatly influenced by the plasma gas characteristics and the particle dynamics inside the nozzle. The heat transfer between the plasma gas and feedstock material increased with the net torch power up to an optimum at 64 kW, at which a maximum of 3.4% of the available plasma energy was absorbed by the feedstock powder. Experimental results using agglomerated 7-8 wt.% yttria-stabilized zirconia (YSZ) powder as feedstock material confirmed the theoretical predictions.

  2. Plasma-Powder Feedstock Interaction During Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Hongbo; Zhang, Baopeng

    2017-01-01

    Plasma spray-physical vapor deposition is a new process developed to produce coatings from the vapor phase. To achieve deposition from the vapor phase, the plasma-feedstock interaction inside the plasma torch, i.e., from the powder injection point to the nozzle exit, is critical. In this work, the plasma characteristics and the momentum and heat transfer between the plasma and powder feedstock at different torch input power levels were investigated theoretically to optimize the net plasma torch power, among other important factors such as the plasma gas composition, powder feed rate, and carrier gas. The plasma characteristics were calculated using the CEA2 code, and the plasma-feedstock interaction was studied inside the torch nozzle at low-pressure (20-25 kPa) conditions. A particle dynamics model was introduced to compute the particle velocity, coupled with Xi Chen's drag model for nonevaporating particles. The results show that the energy transferred to the particles and the coating morphology are greatly influenced by the plasma gas characteristics and the particle dynamics inside the nozzle. The heat transfer between the plasma gas and feedstock material increased with the net torch power up to an optimum at 64 kW, at which a maximum of 3.4% of the available plasma energy was absorbed by the feedstock powder. Experimental results using agglomerated 7-8 wt.% yttria-stabilized zirconia (YSZ) powder as feedstock material confirmed the theoretical predictions.

  3. MicroScale - Atmospheric Pressure Plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Sankaran, Mohan [Case Western Reserve University

    2012-01-25

    Low-temperature plasmas play an essential role in the manufacturing of integrated circuits which are ubiquitous in modern society. In recent years, these top-down approaches to materials processing have reached a physical limit. As a result, alternative approaches to materials processing are being developed that will allow the fabrication of nanoscale materials from the bottom up. The aim of our research is to develop a new class of plasmas, termed “microplasmas” for nanomaterials synthesis. Microplasmas are a special class of plasmas formed in geometries where at least one dimension is less than 1 mm. Plasma confinement leads to several unique properties including high-pressure stability and non-equilibrium that make microplasams suitable for nanomaterials synthesis. Vapor-phase precursors can be dissociated to homogeneously nucleate nanometer-sized metal and alloyed nanoparticles. Alternatively, metal salts dispersed in liquids or polymer films can be electrochemically reduced to form metal nanoparticles. In this talk, I will discuss these topics in detail, highlighting the advantages of microplasma-based systems for the synthesis of well-defined nanomaterials.

  4. [Spectral diagnosis of plasma jet at atmospheric pressure].

    Science.gov (United States)

    Li, Chi; Tang, Xiao-liang; Qiu, Gao

    2008-12-01

    A new approach to surface modification of materials using dielectric barrier discharge (DBD) plasma jet at atmospheric pressure is presented in the present paper. The emission spectral lines of argon plasma jet at atmospheric pressure were recorded by the grating spectrograph HR2000 and computer software. The argon plasma emission spectra, ranging from 300nm to 1000 nm, were measured at different applied voltage. Compared to air plasma emission spectra under the same circumstance, it is shown that all of the spectral lines are attributed to neutral argon atoms. The spectral lines 763.51 and 772.42 nm were chosen to estimate the electron excitation temperature. The purpose of the study is to research the relationship between the applied voltage and temperature to control the process of materials' surface modification promptly. The results show that electron excitation temperature is in the range of 0.1-0.5 eV and increases with increasing applied voltage. In the process of surface modification under the plasma jet, the infrared radiation thermometer was used to measure the material surface temperature under the plasma jet. The results show that the material surface temperature is in the range of 50-100 degrees C and it also increases with increasing applied voltage. Because the material surface was under the plasma jet and its temperature was decided by the plasma, and the material surface temperature increased with increasing the macro-temperature of plasma jet, the relationship between the surface temperature and applied voltage indicates the relationship between the macro-temperature of the plasma jet and the applied voltage approximately. The experimental results indicate that DBD plasma jet at atmospheric pressure is a new approach to improving the quality of materials' surface modification, and spectral diagnosis has proved to be a kind of workable method by choosing suitable applied voltage.

  5. Stimulation of wound healing by helium atmospheric pressure plasma treatment

    Energy Technology Data Exchange (ETDEWEB)

    Nastuta, Andrei Vasile; Topala, Ionut; Pohoata, Valentin; Popa, Gheorghe [Faculty of Physics, Alexandru Ioan Cuza University, Bd. Carol No. 11, 700506, Iasi (Romania); Grigoras, Constantin, E-mail: andrei.nastuta@uaic.ro [Physiopathology Department, Grigore T. Popa University of Medicine and Pharmacy, 700115, Iasi (Romania)

    2011-03-16

    New experiments using atmospheric pressure plasma have found large application in treatment of living cells or tissues, wound healing, cancerous cell apoptosis, blood coagulation on wounds, bone tissue modification, sterilization and decontamination. In this study an atmospheric pressure plasma jet generated using a cylindrical dielectric-barrier discharge was applied for treatment of burned wounds on Wistar rats' skin. The low temperature plasma jet works in helium and is driven by high voltage pulses. Oxygen and nitrogen based impurities are identified in the jet by emission spectroscopy. This paper analyses the natural epithelization of the rats' skin wounds and two methods of assisted epithelization, a classical one using polyurethane wound dressing and a new one using daily atmospheric pressure plasma treatment of wounds. Systemic and local medical data, such as haematological, biochemical and histological parameters, were monitored during entire period of study. Increased oxidative stress was observed for plasma treated wound. This result can be related to the presence in the plasma volume of active species, such as O and OH radicals. Both methods, wound dressing and plasma-assisted epithelization, provided positive medical results related to the recovery process of burned wounds. The dynamics of the skin regeneration process was modified: the epidermis re-epitelization was accelerated, while the recovery of superficial dermis was slowed down.

  6. Stimulation of wound healing by helium atmospheric pressure plasma treatment

    Science.gov (United States)

    Vasile Nastuta, Andrei; Topala, Ionut; Grigoras, Constantin; Pohoata, Valentin; Popa, Gheorghe

    2011-03-01

    New experiments using atmospheric pressure plasma have found large application in treatment of living cells or tissues, wound healing, cancerous cell apoptosis, blood coagulation on wounds, bone tissue modification, sterilization and decontamination. In this study an atmospheric pressure plasma jet generated using a cylindrical dielectric-barrier discharge was applied for treatment of burned wounds on Wistar rats' skin. The low temperature plasma jet works in helium and is driven by high voltage pulses. Oxygen and nitrogen based impurities are identified in the jet by emission spectroscopy. This paper analyses the natural epithelization of the rats' skin wounds and two methods of assisted epithelization, a classical one using polyurethane wound dressing and a new one using daily atmospheric pressure plasma treatment of wounds. Systemic and local medical data, such as haematological, biochemical and histological parameters, were monitored during entire period of study. Increased oxidative stress was observed for plasma treated wound. This result can be related to the presence in the plasma volume of active species, such as O and OH radicals. Both methods, wound dressing and plasma-assisted epithelization, provided positive medical results related to the recovery process of burned wounds. The dynamics of the skin regeneration process was modified: the epidermis re-epitelization was accelerated, while the recovery of superficial dermis was slowed down.

  7. Plasma deposition of amorphous silicon-based materials

    CERN Document Server

    Bruno, Giovanni; Madan, Arun

    1995-01-01

    Semiconductors made from amorphous silicon have recently become important for their commercial applications in optical and electronic devices including FAX machines, solar cells, and liquid crystal displays. Plasma Deposition of Amorphous Silicon-Based Materials is a timely, comprehensive reference book written by leading authorities in the field. This volume links the fundamental growth kinetics involving complex plasma chemistry with the resulting semiconductor film properties and the subsequent effect on the performance of the electronic devices produced. Key Features * Focuses on the plasma chemistry of amorphous silicon-based materials * Links fundamental growth kinetics with the resulting semiconductor film properties and performance of electronic devices produced * Features an international group of contributors * Provides the first comprehensive coverage of the subject, from deposition technology to materials characterization to applications and implementation in state-of-the-art devices.

  8. Atmosphere corrosion behavior of plasma sprayed and laser remelted coatings on copper

    Institute of Scientific and Technical Information of China (English)

    Gongying Liang; T. T. Wong; Geng An; J. M. K. MacAlpine

    2006-01-01

    Nickel and chromium coatings were produced using plasma spraying and laser remelting on the copper sheet. The corrosion test was carried out in an acidic atmosphere, and the corrosive behaviors of both coatings and original copper samples were investigated by using an impedance comparison method. Experimental results show that nickel and chromium coatings display better corrosion resistance properties relative to the original pure copper sample. The corrosion rate of chromium coating is less than that of nickel coating, and corrosion resistances of laser remelted nickel and chromium samples are better thanthose of plasma sprayed samples. The corrosion deposit film of copper is loose compared with nickel and chromium.

  9. Trends in the chemistry of atmospheric deposition and surface waters in the Lake Maggiore catchment

    Directory of Open Access Journals (Sweden)

    M. Rogora

    2001-01-01

    Full Text Available The Lake Maggiore catchment is the area of Italy most affected by acid deposition. Trend analysis was performed on long-term (15-30 years series of chemical analyses of atmospheric deposition, four small rivers draining forested catchments and four high mountain lakes. An improvement in the quality of atmospheric deposition was detected, due to decreasing sulphate concentration and increasing pH. Similar trends were also found in high mountain lakes and in small rivers. Atmospheric deposition, however, is still providing a large and steady flux of nitrogen compounds (nitrate and ammonium which is causing increasing nitrogen saturation in forest ecosystems and increasing nitrate levels in rivers. Besides atmospheric deposition, an important factor controlling water acidification and recovery is the weathering of rocks and soils which may be influenced by climate warming. A further factor is the episodic deposition of Saharan calcareous dust which contributes significantly to base cation deposition. Keywords: trend, atmospheric deposition, nitrogen, stream water chemistry.

  10. Generation of nano roughness on fibrous materials by atmospheric plasma

    Science.gov (United States)

    Kulyk, I.; Scapinello, M.; Stefan, M.

    2012-12-01

    Atmospheric plasma technology finds novel applications in textile industry. It eliminates the usage of water and of hazard liquid chemicals, making production much more eco-friendly and economically convenient. Due to chemical effects of atmospheric plasma, it permits to optimize dyeing and laminating affinity of fabrics, as well as anti-microbial treatments. Other important applications such as increase of mechanical resistance of fiber sleeves and of yarns, anti-pilling properties of fabrics and anti-shrinking property of wool fabrics were studied in this work. These results could be attributed to the generation of nano roughness on fibers surface by atmospheric plasma. Nano roughness generation is extensively studied at different conditions. Alternative explanations for the important practical results on textile materials and discussed.

  11. Preparation of nitrogen doped silicon oxides thin films by plasma polymerization of 3-aminopropyltriethoxylsilane using atmospheric pressure plasma jet

    Science.gov (United States)

    Lin, Yu-Chun; Wang, Meng-Jiy

    2016-01-01

    Surface modification techniques have been applied in various applications including self-cleaning surface, antibacterial filter, and biomaterials. In this study we employed the atmospheric pressure plasma jet (APPJ) deposition, a dry process for surface modification, to deposit 3-aminopropyltriethoxylsilane (APTES) on stainless steel (SS) on the purposes of simultaneously incorporating SiOx and nitrogen containing functionalities for the modulation of biofunctionality. The APPJ deposition allowed to form a thin layer of APTES with linear growth rate by controlling the deposition time. In addition, the surface chemical and physical properties, such as surface chemical composition, wettability, film thickness, and interactions with mammalian cells were evaluated by using different analytical methods. The results showed that the surface wettability was improved significantly due to the APTES deposition along with the increase of the incorporated nitrogen content. Moreover, the viability of L-929 fibroblasts was clearly promoted on the APTES deposited SS, which is most probably due to the thicker deposited films and higher density of nitrogen-containing functional groups. The outcomes of this research showed great potential to apply on metallic substrates in real time for biomedical related applications.

  12. Sterilization of Turmeric by Atmospheric Pressure Dielectric Barrier Discharge Plasma

    Science.gov (United States)

    Setareh, Salarieh; Davoud, Dorranian

    2013-11-01

    In this study atmospheric pressure dielectric barrier discharge (DBD) plasma has been employed for sterilizing dry turmeric powders. A 6 kV, 6 kHz frequency generator was used to generate plasma with Ar, Ar/O2, He, and He/O2 gases between the 5 mm gap of two quartz covered electrodes. The complete sterilization time of samples due to plasma treatment was measured. The most important contaminant of turmeric is bacillus subtilis. The results show that the shortest sterilization time of 15 min is achieved by exposing the samples to Ar/O2 plasma. Survival curves of samples are exponential functions of time and the addition of oxygen to plasma leads to a significant increase of the absolute value of time constant of the curves. Magnitudes of protein and DNA in treated samples were increased to a similar value for all samples. Taste, color, and solubility of samples were not changed after the plasma treatment.

  13. Time Evolution of Artificial Plasma Cloud in Atmospheric Environment

    Institute of Scientific and Technical Information of China (English)

    陆启明; 杨维纮; 刘万东

    2004-01-01

    By analyzing the time evolution of artificial plasma cloud in the high altitude of atmospheric environment, we found that there are two zones, an exponential attenuation zone and a linearly attenuating zone, existing in the spatial distribution of electron density of the artificial plasma clouds. The plasma generator's particle flux density only contributes to the exponential attenuation zone, and has no effect on the linear attenuation zone. The average electron density in the linear attenuation zone is about 10-5 of neutral particle density, and can diffuse over a wider area. The conclusion will supply some valuable references to the research of electromagnetic wave and artificial plasma interaction, the plasma invisibleness research of missile and special aerocraft,and the design of artificial plasma source.

  14. Properties of N-rich Silicon Nitride Film Deposited by Plasma-Enhanced Atomic Layer Deposition

    Science.gov (United States)

    Jhang, Pei-Ci; Lu, Chi-Pin; Shieh, Jung-Yu; Yang, Ling-Wu; Yang, Tahone; Chen, Kuang-Chao; Lu, Chih-Yuan

    2017-07-01

    An N-rich silicon nitride film, with a lower refractive index (RI) than the stoichiometric silicon nitride (RI = 2.01), was deposited by alternating the exposure of dichlorosilane (DCS, SiH2Cl2) and that of ammonia (NH3) in a plasma-enhanced atomic layer deposition (PEALD) process. In this process, the plasma ammonia was easily decomposed to reactive radicals by RF power activating so that the N-rich silicon nitride was easily formed by excited ammonia radicals. The growth kinetics of N-rich silicon nitride were examined at various deposition temperatures ranging from 400 °C to 630 °C; the activation energy (Ea) decreased as the deposition temperature decreased below 550 °C. N-rich silicon nitride film with a wide range of values of refractive index (RI) (RI = 1.86-2.00) was obtained by regulating the deposition temperature. At the optimal deposition temperature, the effects of RF power, NH3 flow rate and NH3 flow time were on the characteristics of the N-rich silicon nitride film were evaluated. The results thus reveal that the properties of the N-rich silicon nitride film that was formed by under plasma-enhanced atomic layer deposition (PEALD) are dominated by deposition temperature. In charge trap flash (CTF) study, an N-rich silicon nitride film was applied to MAONOS device as a charge-trapping layer. The films exhibit excellent electron trapping ability and favor a fresh cell data retention performance as the deposition temperature decreased.

  15. Plasma and Ion Assistance in Physical Vapor Deposition: AHistorical Perspective

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre

    2007-02-28

    Deposition of films using plasma or plasma-assist can betraced back surprisingly far, namely to the 18th century for arcs and tothe 19th century for sputtering. However, only since the 1960s thecoatings community considered other processes than evaporation for largescale commercial use. Ion Plating was perhaps the first importantprocess, introducing vapor ionization and substrate bias to generate abeam of ions arriving on the surface of the growing film. Ratherindependently, cathodic arc deposition was established as an energeticcondensation process, first in the former Soviet Union in the 1970s, andin the 1980s in the Western Hemisphere. About a dozen various ion-basedcoating technologies evolved in the last decades, all characterized byspecific plasma or ion generation processes. Gridded and gridless ionsources were taken from space propulsion and applied to thin filmdeposition. Modeling and simulation have helped to make plasma and ionseffects to be reasonably well understood. Yet--due to the complex, oftennon-linear and non-equilibrium nature of plasma and surfaceinteractions--there is still a place for the experience plasma"sourcerer."

  16. Atmospheric pressure plasma polymerization using double grounded electrodes with He/Ar mixture

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Dong Ha; Kim, Hyun-Jin; Park, Choon-Sang; Tae, Heung-Sik, E-mail: hstae@ee.knu.ac.kr [School of Electronics Engineering, College of IT Engineering, Kyungpook National University, Daegu, 702-701 (Korea, Republic of); Shin, Bhum Jae [Department of Electronics Engineering, Sejong University, Seoul 143-747 (Korea, Republic of); Seo, Jeong Hyun [Department of Electronics Engineering, Incheon National University, Incheon 406-772 (Korea, Republic of)

    2015-09-15

    In this study, we have proposed the double grounded atmospheric pressure plasma jet (2G-APPJ) device to individually control the plasmas in both fragmentation (or active) and recombination (or passive) regions with a mixture of He and Ar gases to deposit organic thin films on glass or Si substrates. Plasma polymerization of acetone has been successfully deposited using a highly energetic and high-density 2G-APPJ and confirmed by scanning electron microscopy (SEM). Plasma composition was measured by optical emission spectroscopy (OES). In addition to a large number of Ar and He spectra lines, we observed some spectra of C{sub 2} and CH species for fragmentation and N{sub 2} (second positive band) species for recombination. The experimental results confirm that the Ar gas is identified as a key factor for facilitating fragmentation of acetone, whereas the He gas helps the plume of plasma reach the substrate on the 2{sup nd} grounded electrode during the plasma polymerization process. The high quality plasma polymerized thin films and nanoparticles can be obtained by the proposed 2G-APPJ device using dual gases.

  17. Atmospheric pressure plasma polymerization using double grounded electrodes with He/Ar mixture

    Directory of Open Access Journals (Sweden)

    Dong Ha Kim

    2015-09-01

    Full Text Available In this study, we have proposed the double grounded atmospheric pressure plasma jet (2G-APPJ device to individually control the plasmas in both fragmentation (or active and recombination (or passive regions with a mixture of He and Ar gases to deposit organic thin films on glass or Si substrates. Plasma polymerization of acetone has been successfully deposited using a highly energetic and high-density 2G-APPJ and confirmed by scanning electron microscopy (SEM. Plasma composition was measured by optical emission spectroscopy (OES. In addition to a large number of Ar and He spectra lines, we observed some spectra of C2 and CH species for fragmentation and N2 (second positive band species for recombination. The experimental results confirm that the Ar gas is identified as a key factor for facilitating fragmentation of acetone, whereas the He gas helps the plume of plasma reach the substrate on the 2nd grounded electrode during the plasma polymerization process. The high quality plasma polymerized thin films and nanoparticles can be obtained by the proposed 2G-APPJ device using dual gases.

  18. Ultrasound enhanced plasma surface modification at atmospheric pressure

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Singh, Shailendra Vikram; Norrman, Kion

    2012-01-01

    Efficiency of atmospheric pressure plasma treatment can be highly enhanced by simultaneous high power ultrasonic irradiation onto the treating surface. It is because ultrasonic waves with a sound pressure level (SPL) above ∼140 dB can reduce the thickness of a boundary gas layer between the plasma...... and the material surface, and thus, many reactive species generated in the plasma can reach the surface before they are inactivated and can be efficiently utilised for surface modification. In the present work, glass fibre reinforced polyester plates were treated using a dielectric barrier discharge and a gliding...... arc at atmospheric pressure to study adhesion improvement. The effect of ultrasonic irradiation with the frequency diapason between 20 and 40 kHz at the SPL of ∼150 dB was investigated. After the plasma treatment without ultrasonic irradiation, the wettability was significantly improved...

  19. Polysilicon Prepared from SIC14 by Atmospheric-Pressure Non-Thermal Plasma%Polysilicon Prepared from SIC14 by Atmospheric-Pressure Non-Thermal Plasma

    Institute of Scientific and Technical Information of China (English)

    李小松; 王楠; 杨晋华; 王友年; 朱爱民

    2011-01-01

    Non-thermal plasma at atmospheric pressure was explored for the preparation of polysilicon from SiCl4. The power supply sources of positive pulse and alternating current (8 kHz and 100 kHz) were compared for polysilicon preparation. The samples prepared by using the 100 kHz power source were crystalline silicon. The effects of H2 and SiCl4 volume fractions were investigated. The optical emission spectra showed that silicon species played an important role in polysilicon deposition

  20. Properties of CdTe layers deposited by a novel method -Pulsed Plasma Deposition

    OpenAIRE

    Ancora, C.; Nozar, P.; Mittica, G.; Prescimone, F.; A. Neri; Contaldi, S.; Milita, S.; Albonetti, C.; Corticelli, F.; Brillante, A.; Bilotti, I.; Tedeschi, G.; Taliani, C.

    2011-01-01

    CdTe and CdS are emerging as the most promising materials for thin film photovoltaics in the quest of the achievement of grid parity. The major challenge for the advancement of grid parity is the achievement of high quality at the same time as low fabrication cost. The present paper reports the results of the new deposition technique, Pulsed Plasma Deposition (PPD), for the growth of the CdTe layers on CdS/ZnO/quartz and quartz substrates. The PPD method allows to deposit at low temperature. ...

  1. Characteristics of RF Cold Plasma at Atmospheric Pressure

    Institute of Scientific and Technical Information of China (English)

    QIU Liang; MENG Yuedong; SHU Xingsheng

    2007-01-01

    The characteristics of a stable discharge at atmospheric pressure is investigated.The plasma source consisted of two closely spaced parallel-plated perforated electrodes,driven by a radio frequency power to generate a uniform cold plasma in Helium at atmospheric pressure.Both alpha and gamma modes were clearly observed.The hollow cathode effects were found in the discharge.The influence of the dielectric barrier on the discharge was also investigated by utilizing a surface-anodized aluminium electrode as the anode.

  2. The Interactions of Two Cold Atmospheric Plasma Jets

    Institute of Scientific and Technical Information of China (English)

    TANG Daotan; REN Chunsheng; WANG Dezhen; NIE Qiuyue

    2009-01-01

    This paper presents the interactions between two cold atmospheric plasma jets. By changing the experimental conditions including the gas flow rate, the applied voltage, the power supply frequency and the inter-electrode distance d, three different interaction modes, attraction, repulsion and combination, were observed. It is shown that the interaction modes of the two jets are principally affected by the electrodes, the gas flow rate, the plasma jets and the power supply frequency.

  3. Caracterisation of Titanium Nitride Layers Deposited by Reactive Plasma Spraying

    Science.gov (United States)

    Roşu, Radu Alexandru; Şerban, Viorel-Aurel; Bucur, Alexandra Ioana; Popescu, Mihaela; Uţu, Dragoş

    2011-01-01

    Forming and cutting tools are subjected to the intense wear solicitations. Usually, they are either subject to superficial heat treatments or are covered with various materials with high mechanical properties. In recent years, thermal spraying is used increasingly in engineering area because of the large range of materials that can be used for the coatings. Titanium nitride is a ceramic material with high hardness which is used to cover the cutting tools increasing their lifetime. The paper presents the results obtained after deposition of titanium nitride layers by reactive plasma spraying (RPS). As deposition material was used titanium powder and as substratum was used titanium alloy (Ti6Al4V). Macroscopic and microscopic (scanning electron microscopy) images of the deposited layers and the X ray diffraction of the coatings are presented. Demonstration program with layers deposited with thickness between 68,5 and 81,4 μm has been achieved and presented.

  4. Plasma enhanced diamond deposition on steel and Si substrates

    Institute of Scientific and Technical Information of China (English)

    Y.S. Li; Y. Tang; W. Chen; Q. Yang; C. Xiao; A. Hirose

    2009-01-01

    Diamond growth on Fe-Cr-Al-Si steel and Si substrates was comparatively investigated in microwave plasma enhanced chemical vapor deposition (MPCVD) reactor with different deposition parameters. Adherent nanocrystalline diamond films were directly deposited on this steel substrate under a typical deposition condition, whereas microcrystalline diamond films were produced on Si wafer. With increasing CH4 concentration, reaction pressure, or the total gas flow rate, the quality of nanocrystalline diamond films formed on Fe-Cr-Al-Si substrates is gradually deteriorated in terms of density and adhesion. This impaired diamond quality on steels is primarily associated with a combined effect by the substrate composition and the specific process conditions that favor excessive nucleation of diamond.

  5. Atmospheric-Pressure Plasma Interaction with Soft Materials as Fundamental Processes in Plasma Medicine.

    Science.gov (United States)

    Takenaka, Kosuke; Miyazaki, Atsushi; Uchida, Giichiro; Setsuhara, Yuichi

    2015-03-01

    Molecular-structure variation of organic materials irradiated with atmospheric pressure He plasma jet have been investigated. Optical emission spectrum in the atmospheric-pressure He plasma jet has been measured. The spectrum shows considerable emissions of He lines, and the emission of O and N radicals attributed to air. Variation in molecular structure of Polyethylene terephthalate (PET) film surface irradiated with the atmospheric-pressure He plasma jet has been observed via X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FT-IR). These results via XPS and FT-IR indicate that the PET surface irradiated with the atmospheric-pressure He plasma jet was oxidized by chemical and/or physical effect due to irradiation of active species.

  6. Atmospheric heavy metal deposition in the Copenhagen area

    DEFF Research Database (Denmark)

    Andersen, Allan; Hovmand, Mads Frederik; Johnsen, Ib

    1978-01-01

    Atmospheric dry and wet deposition (bulk precipitation) of the heavy metals Cu, Pb, Zn, Ni, V and Fe over the Copenhagen area was measured by sampling in plastic funnels from 17 stations during a twelve-month period. Epigeic bryophytes from 100 stations in the area were analysed for the heavy...... and heavy metal concentration in lichens and bryophytes. An exponential correlation was found between bulk precipitation and heavy metal concentration in soil. Regional variation of the heavy metal levels in the Copenhagen area was described and three sub-areas with high metal burdens were distinguished....... The heavy metal gradients from a secondary smelter in one of these sub-areas were steepest in soil compared with lichens and bryophytes....

  7. Three Filtered Vacuum Arc Plasma Sources Deposition & Implantation System

    Institute of Scientific and Technical Information of China (English)

    WU Xian-ying; ZHANG Hui-xing; LI Qiang

    2004-01-01

    A deposition & implantation system, which includes three filtered vacuum arc plasma sources, has been built. Vacuum arc discharge is used to produce high-density metal plasma; Curved magnetic filtering technique is used to transfer the plasma into out-of-sight vacuum chamber and reduce macro-particles from the vacuum arc plasma in order to drastically reduce the macro-particles contamination of the films. The up to 30 kV negative bias applied to the target can be used for ion implantation in order to improve the film adhesion; or for ion sputtering to clear the substrate surface. The 0 to 300 V negative bias can be used to adjust the ion energy which forming films. The system is designed for various thin films synthesizing, such as single-layer, compound layer, multi-layer films. It's principle, components and applications are described in the literature.

  8. Atmospheric pressure plasma surface modification of carbon fibres

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Løgstrup Andersen, Tom; Michelsen, Poul

    2008-01-01

    Carbon fibres are continuously treated with dielectric barrier discharge plasma at atmospheric pressure in various gas conditions for adhesion improvement in mind. An x-ray photoelectron spectroscopic analysis indicated that oxygen is effectively introduced onto the carbon fibre surfaces by He, H...... temperature for a month the O/C ratio at the plasma treated surfaces decreased to 0.151, which is close to that of the untreated ones. It can be attributed to the adsorption of hydrocarbon contamination at the plasma treated surfaces....

  9. An Atmospheric Large-Scale Cold Plasma Jet

    Institute of Scientific and Technical Information of China (English)

    吕晓桂; 任春生; 马腾才; 冯岩; 王德真

    2012-01-01

    This letter reports on the generation and characteristics of a large-scale dielectric barrier discharge plasma jet at atmospheric pressure. With appropriate parameters, diffuse plasma with a 50×5 mm2 cross-sectional area is obtained. The characteristics of the discharges are diag- nosed by using electrical and optical methods. In addition to being generated in helium, plasma is also generated in a mixed gas of helium and oxygen. The oxygen atomic radiant intensity (3p5P→ 3s5S, 3p3P→3s3S transition) is not proportional to the proportion of oxygen in the gas mixture, as shown by the experimental results.

  10. Very high frequency plasma reactant for atomic layer deposition

    Science.gov (United States)

    Oh, Il-Kwon; Yoo, Gilsang; Yoon, Chang Mo; Kim, Tae Hyung; Yeom, Geun Young; Kim, Kangsik; Lee, Zonghoon; Jung, Hanearl; Lee, Chang Wan; Kim, Hyungjun; Lee, Han-Bo-Ram

    2016-11-01

    Although plasma-enhanced atomic layer deposition (PE-ALD) results in several benefits in the formation of high-k dielectrics, including a low processing temperature and improved film properties compared to conventional thermal ALD, energetic radicals and ions in the plasma cause damage to layer stacks, leading to the deterioration of electrical properties. In this study, the growth characteristics and film properties of PE-ALD Al2O3 were investigated using a very-high-frequency (VHF) plasma reactant. Because VHF plasma features a lower electron temperature and higher plasma density than conventional radio frequency (RF) plasma, it has a larger number of less energetic reaction species, such as radicals and ions. VHF PE-ALD Al2O3 shows superior physical and electrical properties over RF PE-ALD Al2O3, including high growth per cycle, excellent conformality, low roughness, high dielectric constant, low leakage current, and low interface trap density. In addition, interlayer-free Al2O3 on Si was achieved in VHF PE-ALD via a significant reduction in plasma damage. VHF PE-ALD will be an essential process to realize nanoscale devices that require precise control of interfaces and electrical properties.

  11. Power Deposition on Tokamak Plasma-Facing Components

    CERN Document Server

    Arter, Wayne; Fishpool, Geoff

    2014-01-01

    The SMARDDA software library is used to model plasma interaction with complex engineered surfaces. A simple flux-tube model of power deposition necessitates the following of magnetic fieldlines until they meet geometry taken from a CAD (Computer Aided Design) database. Application is made to 1) models of ITER tokamak limiter geometry and 2) MASTU tokamak divertor designs, illustrating the accuracy and effectiveness of SMARDDA, even in the presence of significant nonaxisymmetric ripple field. SMARDDA's ability to exchange data with CAD databases and its speed of execution also give it the potential for use directly in the design of tokamak plasma facing components.

  12. Atmospheric pressure plasmas for aerosols processes in materials and environment

    Science.gov (United States)

    Borra, J. P.; Jidenko, N.; Bourgeois, E.

    2009-08-01

    The paper highlights applications of some atmospheric pressure plasmas (dc-corona, streamer and spark and ac-Dielectric Barrier Discharges) to aerosol processes for Materials and Environment (filtration, diagnostics). The production of vapor i.e. condensable gaseous species, leads to nano-sized particles by physical and chemical routes of nucleation in these AP plasmas: (i) when dc streamer and spark filamentary discharges as well as ac filamentary dielectric barrier discharges interact with metal or dielectric surfaces, and (ii) when discharges induce reactions with gaseous precursors in volume. It is shown how composition, size and structure of primary nano-particles are related to plasma parameters (energy, number per unit surface and time and thermal gradients). Then the growth by coagulation controls the final size of agglomerates versus plasma parameters and transit time in and after the plasma. Charging and electro-thermal collection are depicted to account for the related potential applications of controlled kinematics of charged aerosol.

  13. Seasonal and spatial variations of atmospheric trace elemental deposition in the Aliaga industrial region, Turkey

    Science.gov (United States)

    Kara, Melik; Dumanoglu, Yetkin; Altiok, Hasan; Elbir, Tolga; Odabasi, Mustafa; Bayram, Abdurrahman

    2014-11-01

    Atmospheric bulk deposition (wet + dry deposition) samples (n = 40) were collected concurrently at ten sites in four seasons between June 2009 and April 2010 in the Aliaga heavily industrialized region, Turkey, containing a number of significant air pollutant sources. Analyses of trace elements were carried out using inductively coupled plasma-mass spectrometry (ICP-MS). While there were significant differences in the particulate matter (PM) deposition fluxes among the sampling sites, seasonal variations were not statistically significant (Kruskal-Wallis test, p deposition and elemental fluxes were increased at the sampling sites in the vicinity of industrial activities. The crustal elements (i.e., Ca, Mg) and some anthropogenic elements (such as Fe, Zn, Mn, Pb, Cu, and Cr) were high, and the highest fluxes were mostly measured in summer and winter seasons. The enrichment factor (EF) and principal component analysis (PCA) was applied to the data to determine the possible sources in the study area. High EF values were obtained for the anthropogenic elements such as Ag, Cd, Zn, Pb, Cu and Sb. The possible sources were identified as anthropogenic sources (i.e., iron-steel production) (45.4%), crustal and re-suspended dust (27.1%), marine aerosol (7.9%), and coal and wood combustion (8.2%). Thus, the iron-steel production and its related activities were found to be the main pollutant sources for this region.

  14. Atmospheric Pressure Plasma Based Flame Control and Diagnostics

    Science.gov (United States)

    2015-01-01

    TYPE 3. DATES COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Atmospheric Pressure Plasma Based Flame Control and Diagnostics 5a...to 10%)  Flame speed enhancement (>20%)  Extension of lean limit (factor of two)  Distributed ignition  Development of new diagnostics

  15. Atmospheric pressure plasma CVD as a tool to functionalise wound dressings.

    Science.gov (United States)

    Spange, Sebastian; Pfuch, Andreas; Wiegand, Cornelia; Beier, Oliver; Hipler, Uta C; Grünler, Bernd

    2015-02-01

    The main goal of this investigation was the preparation of an antibacterial layer system for additional modification of wound dressings with atmospheric plasma. Furthermore, the modified wound dressings were checked on there bactericidal and cytotoxic activity. The layer system was applied by using a novel atmospheric pressure plasma chemical vapour deposition technique on a variety of textile substrates which are suitable as wound dressing materials. The layer system composed of silicon dioxide with in situ generated embedded silver nanoparticles. The bactericidal activity of the produced wound dressings was investigated against different bacteria like Staphylococcus aureus and Klebsiella pneumoniae while the cytotoxic potential of the coated wound dressings was verified using human keratinocytes. Even at low concentrations of silver precursor a strong antibacterial effect was observed in direct contact with S. aureus and K. pneumoniae. Furthermore, extractions produced from the coated textiles showed a good antibacterial effect. By means of optimised coating parameters a therapeutic window for those wound dressings could be identified. Consequently, the atmospheric pressure plasma chemical vapour deposition technique promise an effective and low cost modification of wound dressing materials.

  16. Use of Cold Atmospheric Plasma to Detoxify Hazelnuts from Aflatoxins

    Directory of Open Access Journals (Sweden)

    Ilenia Siciliano

    2016-04-01

    Full Text Available Aflatoxins, produced by Aspergillus flavus and A. parasiticus, can contaminate different foodstuffs, such as nuts. Cold atmospheric pressure plasma has the potential to be used for mycotoxin detoxification. In this study, the operating parameters of cold atmospheric pressure plasma were optimized to reduce the presence of aflatoxins on dehulled hazelnuts. First, the effect of different gases was tested (N2, 0.1% O2 and 1% O2, 21% O2, then power (400, 700, 1000, 1150 W and exposure time (1, 2, 4, and 12 min were optimized. In preliminary tests on aflatoxin standard solutions, this method allowed to obtain a complete detoxification using a high power for a few minutes. On hazelnuts, in similar conditions (1000 W, 12 min, a reduction in the concentration of total aflatoxins and AFB1 of over 70% was obtained. Aflatoxins B1 and G1 were more sensitive to plasma treatments compared to aflatoxins B2 and G2, respectively. Under plasma treatment, aflatoxin B1 was more sensitive compared to aflatoxin G1. At the highest power, and for the longest time, the maximum temperature increment was 28.9 °C. Cold atmospheric plasma has the potential to be a promising method for aflatoxin detoxification on food, because it is effective and it could help to maintain the organoleptic characteristics.

  17. Use of Cold Atmospheric Plasma to Detoxify Hazelnuts from Aflatoxins.

    Science.gov (United States)

    Siciliano, Ilenia; Spadaro, Davide; Prelle, Ambra; Vallauri, Dario; Cavallero, Maria Chiara; Garibaldi, Angelo; Gullino, Maria Lodovica

    2016-04-26

    Aflatoxins, produced by Aspergillus flavus and A. parasiticus, can contaminate different foodstuffs, such as nuts. Cold atmospheric pressure plasma has the potential to be used for mycotoxin detoxification. In this study, the operating parameters of cold atmospheric pressure plasma were optimized to reduce the presence of aflatoxins on dehulled hazelnuts. First, the effect of different gases was tested (N₂, 0.1% O₂ and 1% O₂, 21% O₂), then power (400, 700, 1000, 1150 W) and exposure time (1, 2, 4, and 12 min) were optimized. In preliminary tests on aflatoxin standard solutions, this method allowed to obtain a complete detoxification using a high power for a few minutes. On hazelnuts, in similar conditions (1000 W, 12 min), a reduction in the concentration of total aflatoxins and AFB₁ of over 70% was obtained. Aflatoxins B₁ and G₁ were more sensitive to plasma treatments compared to aflatoxins B₂ and G₂, respectively. Under plasma treatment, aflatoxin B₁ was more sensitive compared to aflatoxin G₁. At the highest power, and for the longest time, the maximum temperature increment was 28.9 °C. Cold atmospheric plasma has the potential to be a promising method for aflatoxin detoxification on food, because it is effective and it could help to maintain the organoleptic characteristics.

  18. Atmospheric pressure plasma jet treatment of Salmonella Enteritidis inoculated eggshells.

    Science.gov (United States)

    Moritz, Maike; Wiacek, Claudia; Koethe, Martin; Braun, Peggy G

    2017-03-20

    Contamination of eggshells with Salmonella Enteritidis remains a food safety concern. In many cases human salmonellosis within the EU can be traced back to raw or undercooked eggs and egg products. Atmospheric pressure plasma is a novel decontamination method that can reduce a wide range of pathogens. The aim of this work was to evaluate the possibility of using an effective short time cold plasma treatment to inactivate Salmonella Enteritidis on the eggshell. Therefore, artificially contaminated eggshells were treated with an atmospheric pressure plasma jet under different experimental settings with various exposure times (15-300s), distances from the plasma jet nozzle to the eggshell surface (5, 8 or 12mm), feed gas compositions (Ar, Ar with 0.2, 0.5 or 1.0% O2), gas flow rates (5 and 7slm) and different inoculations of Salmonella Enteritidis (10(1)-10(6)CFU/cm(2)). Atmospheric pressure plasma could reduce Salmonella Enteritidis on eggshells significantly. Reduction factors ranged between 0.22 and 2.27 log CFU (colony-forming units). Exposure time and, particularly at 10(4)CFU/cm(2) inoculation, feed gas had a major impact on Salmonella reduction. Precisely, longer exposure times led to higher reductions and Ar as feed gas was more effective than ArO2 mixtures.

  19. Formation and characterization of hydrophobic glass surface treated by atmospheric pressure He/CH4 plasma

    Science.gov (United States)

    Noh, Sooryun; Youn Moon, Se

    2014-01-01

    Atmospheric pressure helium plasmas, generated in the open air by 13.56 MHz rf power, were applied for the glass surface wettability modification. The plasma gas temperature, measured by the spectroscopic method, was under 400 K which is low enough to treat the samples without thermal damages. The hydrophobicity of the samples determined by the water droplet contact angle method was dependent on the methane gas content and the plasma exposure time. Adding the methane gas by a small amount of 0.25%, the contact angle was remarkably increased from 10° to 83° after the 10 s plasma treatment. From the analysis of the treated surface and the plasma, it was shown that the deposition of alkane functional groups such as C-H stretch, CH2 bend, and CH3 bend was one of the contributing factors for the hydrophobicity development. In addition, the hydrophobic properties lasted over 2 months even after the single treatment. From the results, the atmospheric pressure plasma treatment promises the fast and low-cost method for the thermally-weak surface modification.

  20. Multilayer Coating Formation at the Deposition from Plasma

    OpenAIRE

    Shanin, Sergei Aleksandrovich; Knyazeva, Anna Georgievna

    2016-01-01

    The numerical experiment was carried out for the process of the coating composition formation during deposition from plasma. The chemical reactions between elements are taken into account. The nonuniform composition of the coating is determined by various transfer processes, including diffusion under stress action. To find the stress field the equilibrium problem was solved numerically because all physical and mechanical properties depend on composition. Stress field has been also obtained no...

  1. Cold atmospheric plasma sterilization: from bacteria to biomolecules

    Science.gov (United States)

    Kong, Michael

    2009-10-01

    Although ionized gases have been known to have biological effects for more than 100 years, their impact on the practice in healthcare service became very significant only recently. Today, plasma-based surgical tools are used for tissue reduction and blood coagulation as surgical procedures. Most significant however is the speed at which low-temperature gas plasmas are finding new applications in medicine and biology, including plasma sterilization, wound healing, and cancer therapies just to name a few. In the terminology of biotechnology, the ``pipeline'' is long and exciting. This presentation reviews the current status of the field with a particular emphasis on plasma inactivation of microorganisms and biomolecules, for which comprehensive scientific evidence has been obtained. Some of the early speculations of biocidal plasma species are now being confirmed through a combination of optical emission spectroscopy, laser-induced fluorescence, mass spectrometry, fluid simulation and biological sensing with mutated bacteria. Similarly, fundamental studies are being performed to examine cell components targeted by gas plasmas, from membrane, through lipid and membrane proteins, to DNA. Scientific challenge is significant, as the usual complexity of plasma dynamics and plasma chemistry is compounded by the added complication that cells are live and constantly evolving. Nevertheless, the current understanding of plasma inactivation currently provides strong momentum for plasma decontamination technologies to be realized in healthcare. We will discuss the issue of protein and tissue contaminations of surgical instruments and how cold atmospheric plasmas may be used to degrade and reduce their surface load. In the context of plasma interaction with biomolecules, we will consider recent data of plasma degradation of adhesion proteins of melanoma cells. These adhesion proteins are important for cancer cell migration and spread. If low-temperature plasmas could be used to

  2. Novel applications of atmospheric pressure plasma on textile materials

    Science.gov (United States)

    Cornelius, Carrie Elizabeth

    Various applications of atmospheric pressure plasma are investigated in conjunction with polymeric materials including paper, polypropylene non-woven fabric, and cotton. The effect of plasma on bulk and surface properties is examined by treating both cellulosic pulp and prefabricated paper with various plasma-gas compositions. After treatment, pulp is processed into paper and the properties are compared. The method of pulp preparation is found to be more significant than the plasma, but differences in density, strength, and surface roughness are apparent for the pulp vs. paper plasma treatments. The plasma is also used to remove sizes of PVA and starch from poly/cotton and cotton fabric respectively. In both cases plasma successfully removes a significant amount of size, but complete size removal is not achieved. Subsequent washes (PVA) or scouring (cotton) to remove the size are less successful than a control, suggesting the plasma is crosslinking the size that is not etched away. However, at short durations in cold water using an oxygen plasma, slightly more PVA is removed than with a control. For the starch sized samples, plasma and scouring are never as successful at removing starch as a conventional enzyme, but plasma improves dyeability without need for scouring. Plasma is also used to graft chemicals to the surface of polypropylene and cotton fabric. HTCC, an antimicrobial is grafted to polypropylene with successful grafting indicated by x-ray photoemission spectroscopy (XPS), dye tests, and Fourier transform infrared spectroscopy (FTIR). Antimicrobial activity of the grafted samples is also characterized. 3ATAC, a vinyl monomer is also grafted to polypropylene and to cotton. Additives including Mohr's salt, potassium persulfate, and diacrylate are assessed to increase yield. Successful grafting of 3ATAC is confirmed by XPS and dye testing. A combination of all three additives is identified as optimum for maximizing graft yield.

  3. Application of atmospheric pressure plasma in polymer and composite adhesion

    Science.gov (United States)

    Yu, Hang

    An atmospheric pressure helium and oxygen plasma was used to investigate surface activation and bonding in polymer composites. This device was operated by passing 1.0-3.0 vol% of oxygen in helium through a pair of parallel plate metal electrodes powered by 13.56 or 27.12 MHz radio frequency power. The gases were partially ionized between the capacitors where plasma was generated. The reactive species in the plasma were carried downstream by the gas flow to treat the substrate surface. The temperature of the plasm gas reaching the surface of the substrate did not exceed 150 °C, which makes it suitable for polymer processing. The reactive species in the plasma downstream includes ~ 1016-1017 cm-3 atomic oxygen, ~ 1015 cm-3 ozone molecule, and ~ 10 16 cm-3 metastable oxygen molecule (O2 1Deltag). The substrates were treated at 2-5 mm distance from the exit of the plasma. Surface properties of the substrates were characterized using water contact angle (WCA), atomic force microscopy (AFM), infrared spectroscopy (IR), and X-ray photoelectron spectroscopy (XPS). Subsequently, the plasma treated samples were bonded adhesively or fabricated into composites. The increase in mechanical strength was correlated to changes in the material composition and structure after plasma treatment. The work presented hereafter establishes atmospheric pressure plasma as an effective method to activate and to clean the surfaces of polymers and composites for bonding. This application can be further expanded to the activation of carbon fibers for better fiber-resin interactions during the fabrication of composites. Treating electronic grade FR-4 and polyimide with the He/O2 plasma for a few seconds changed the substrate surface from hydrophobic to hydrophilic, which allowed complete wetting of the surface by epoxy in underfill applications. Characterization of the surface by X-ray photoelectron spectroscopy shows formation of oxygenated functional groups, including hydroxyl, carbonyl, and

  4. A model for plasma modification of polypropylene using atmospheric pressure discharges

    CERN Document Server

    Dorai, R

    2003-01-01

    Atmospheric pressure plasmas are commonly used to improve the wetting and adhesion properties of polymers. In spite of their use, the mechanisms for achieving these properties are unclear. In this regard, we report on a computational investigation of the gas phase and surface kinetics during humid-air corona treatment of polypropylene (PP) and the resulting modification of its surface properties while varying energy deposition, relative humidity (RH), web speed, and gas temperature. Using results from a global plasma chemistry model validated against experiments, we found that increasing energy deposition increased the densities of alcohol, carbonyl, acid, and peroxy radicals on the PP surface. In doing so, significant amounts of gas phase O sub 3 and N sub x O sub y are produced. Increasing the RH increased the production of peroxy and acid groups, while decreasing those of alcohol and carbonyl groups. Production of O sub 3 decreased while that of HNO sub 3 increased. Increasing the temperature decreased the...

  5. Atmospheric deposition, operational report for air pollution 2003. NOVA 2003; Atmosfaerisk deposition, driftsrapport for Luftforurening i 2003 NOVA 2003

    Energy Technology Data Exchange (ETDEWEB)

    Ellermann, T.; Hertel, O.; Ambelas Skjoeth, C.; Kemp, K.; Monies, C.

    2004-12-01

    This report presents measurements and calculations from the atmospheric part of NOVA 2003 and covers results for 2003. It summarises the main results concerning concentrations and depositions of nitrogen, phosphorous and sulphur compounds related to eutrofication and acidification and selected heavy metals. Depositions of atmospheric compounds to Danish marine waters as well as land surface are presented. The measurements in the monitoring programme are supplemented with model calculations of concentrations and depositions of nitrogen and sulphur compounds to Danish land surfaces as well as marine waters, fjords and bays using the ACDEP model (Atmospheric Chemistry and Deposition). The model is a so-called trajectory model and simulates the physical and chemical processes in the atmosphere using meteorological and emission data input. (BA)

  6. Surface modification of polymeric materials by cold atmospheric plasma jet

    Science.gov (United States)

    Kostov, K. G.; Nishime, T. M. C.; Castro, A. H. R.; Toth, A.; Hein, L. R. O.

    2014-09-01

    In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source - the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40° in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure.

  7. Application of atmospheric pressure plasma on polyethylene for increased prosthesis adhesion

    Energy Technology Data Exchange (ETDEWEB)

    Van Vrekhem, S., E-mail: stijn.vanvrekhem@ugent.be [Research Unit Plasma Technology (RUPT), Department of Applied Physics, Faculty of Engineering and Architecture, Ghent University, Sint-Pietersnieuwstraat 41 B4, 9000 Ghent (Belgium); Cools, P. [Research Unit Plasma Technology (RUPT), Department of Applied Physics, Faculty of Engineering and Architecture, Ghent University, Sint-Pietersnieuwstraat 41 B4, 9000 Ghent (Belgium); Declercq, H. [Research Unit Plasma Technology (RUPT), Department of Applied Physics, Faculty of Engineering and Architecture, Ghent University, Sint-Pietersnieuwstraat 41 B4, 9000 Ghent (Belgium); Tissue Engineering Group, Department of Basic Medical Sciences, Faculty of Medicine and Health Sciences, Ghent University, De Pintelaan 185 6B3, 9000 Ghent (Belgium); Van Tongel, A. [Department of Orthopaedic Surgery and Traumatology, Ghent University Hospital, De Pintelaan 185 13K12, 9000 Ghent (Belgium); Vercruysse, C.; Cornelissen, M. [Tissue Engineering Group, Department of Basic Medical Sciences, Faculty of Medicine and Health Sciences, Ghent University, De Pintelaan 185 6B3, 9000 Ghent (Belgium); De Geyter, N.; Morent, R. [Research Unit Plasma Technology (RUPT), Department of Applied Physics, Faculty of Engineering and Architecture, Ghent University, Sint-Pietersnieuwstraat 41 B4, 9000 Ghent (Belgium)

    2015-12-01

    Biopolymers are often subjected to surface modification in order to improve their surface characteristics. The goal of this study is to show the use of plasma technology to enhance the adhesion of ultra-high molecular weight polyethylene (UHMWPE) shoulder prostheses. Two different plasma techniques (low pressure plasma activation and atmospheric pressure plasma polymerization) are performed on UHMWPE to increase the adhesion between (1) the polymer and polymethylmethacrylate (PMMA) bone cement and (2) the polymer and osteoblast cells. Both techniques are performed using a dielectric barrier discharge (DBD). A previous paper showed that low pressure plasma activation of UHMWPE results in the incorporation of oxygen-containing functional groups, which leads to an increased surface wettability. Atmospheric pressure plasma polymerization of methylmethacrylate (MMA) on UHMWPE results in a PMMA-like coating, which could be deposited with a high degree of control of chemical composition and layer thickness. The thin film also proved to be relatively stable upon incubation in a phosphate buffer solution (PBS). This paper discusses the next stage of the study, which includes testing the adhesion of the plasma-activated and plasma-polymerized samples to bone cement through pull-out tests and testing the cell adhesion and proliferation on the samples. In order to perform the pull-out tests, all samples were cut to standard dimensions and fixed in bone cement in a reproducible way with a sample holder specially designed for this purpose. The cell adhesion and proliferation were tested by means of an MTS assay and live/dead staining after culturing MC3T3 osteoblast cells on UHMWPE samples. The results show that both plasma activation and plasma polymerization significantly improve the adhesion to bone cement and enhance cell adhesion and proliferation. In conclusion, it can be stated that the use of plasma technology can lead to an implant with improved quality and a subsequent

  8. Gas Diffusion Barriers Prepared by Spatial Atmospheric Pressure Plasma Enhanced ALD.

    Science.gov (United States)

    Hoffmann, Lukas; Theirich, Detlef; Pack, Sven; Kocak, Firat; Schlamm, Daniel; Hasselmann, Tim; Fahl, Henry; Räupke, André; Gargouri, Hassan; Riedl, Thomas

    2017-02-01

    In this work, we report on aluminum oxide (Al2O3) gas permeation barriers prepared by spatial ALD (SALD) at atmospheric pressure. We compare the growth characteristics and layer properties using trimethylaluminum (TMA) in combination with an Ar/O2 remote atmospheric pressure plasma for different substrate velocities and different temperatures. The resulting Al2O3 films show ultralow water vapor transmission rates (WVTR) on the order of 10(-6) gm(-2)d(-1). In notable contrast, plasma based layers already show good barrier properties at low deposition temperatures (75 °C), while water based processes require a growth temperature above 100 °C to achieve equally low WVTRs. The activation energy for the water permeation mechanism was determined to be 62 kJ/mol.

  9. Surface modification of polymeric materials by cold atmospheric plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Kostov, K.G., E-mail: kostov@feg.unesp.br [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil); Nishime, T.M.C.; Castro, A.H.R. [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil); Toth, A. [Institute of Material and Environmental Chemistry, Hungarian Academy of Science P.O. Box 17, H-1525, Budapest (Hungary); Hein, L.R.O. [Faculty of Engineering in Guaratinguetá–FEG, Universidade Estadual Paulista–UNESP Guaratiguetá, 12516-410, SP (Brazil)

    2014-09-30

    Highlights: • We investigate polymer surface modification by atmospheric pressure plasma jet APPJ. • Jet operation conditions for uniform surface modification were determined. • The APPJ added O atoms to the polymer surface and also enhanced the roughness. • The degree of polymer surface modification by APPJ and DBD were compared. • The APPJ is more efficient in attaching O atoms and produces less polymer fragments. - Abstract: In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source – the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40° in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure.

  10. In situ impedance measurement of microwave atmospheric pressure plasma

    Science.gov (United States)

    Lee, S. T.; Nam, W. J.; Lee, J. K.; Yun, G. S.

    2017-04-01

    The impedance of atmospheric pressure argon plasma jets driven by microwave frequency is determined in situ by a novel ‘two frequency method’. In the conventional method of reflection coefficient ({{S}}11) measurement, the frequency of the driving microwave power is scanned, which inevitably affects the plasma characters and leads to uncertainty in the estimated plasma impedance. In our proposed method, the frequency-scanning signal additional to the driving power is used to measure {{S}}11 over a wide frequency range, which enables accurate determination of the plasma impedance based on an equivalent circuit model. The measured resistance and reactance of the plasma increase with the driving power in agreement with the transmission line theory. Based on this in situ measurement of the plasma impedance, the net power coupled to the plasma has been determined. The overall power efficiency remains approximately unchanged around 45% for different input power levels owing to the competing effects between the impedance mismatch and the volume change of the plasma.

  11. On the mechanism of atmospheric pressure plasma plume

    Science.gov (United States)

    Chen, Longwei; Zhao, Peng; Shu, Xingsheng; Shen, Jie; Meng, Yuedong

    2010-08-01

    For the purpose of unveiling the parameters influencing the length of atmospheric pressure plasma plume, an over 165 cm long argon plasma plume is generated in the quartz tube attached to the nozzle of the device. Dependence of plasma length on discharge parameters such as applied voltage, frequency of power supply, and argon gas flow rate was investigated. Experimental results indicated that (a) the applied voltage plays crucial roles on plasma plume length, that is, the plasma plume length exponentially increases with the applied voltage, (b) the plasma plume length increases with frequency, more obviously when the applied voltage is higher, (c) the plasma plume length increases with argon gas flow rate, reaches its maximum at critical value of the gas flow rate, and then decreases again. An evaluation of the physical phenomena involved in streamer propagation, particularly of the energy balance, was investigated. The numerical results were qualitatively consistent with previous experimental results by successfully indicating the high velocity of "plasma bullet" and providing physical mechanism of energy balance determining streamer length.

  12. Sources, transport and deposition of iron in the global atmosphere

    Science.gov (United States)

    Wang, R.; Balkanski, Y.; Boucher, O.; Bopp, L.; Chappell, A.; Ciais, P.; Hauglustaine, D.; Peñuelas, J.; Tao, S.

    2015-06-01

    Atmospheric deposition of iron (Fe) plays an important role in controlling oceanic primary productivity. However, the sources of Fe in the atmosphere are not well understood. In particular, the combustion sources of Fe and the subsequent deposition to the oceans have been accounted for in only few ocean biogeochemical models of the carbon cycle. Here we used a mass-balance method to estimate the emissions of Fe from the combustion of fossil fuels and biomass by accounting for the Fe contents in fuel and the partitioning of Fe during combustion. The emissions of Fe attached to aerosols from combustion sources were estimated by particle size, and their uncertainties were quantified by a Monte Carlo simulation. The emissions of Fe from mineral sources were estimated using the latest soil mineralogical database to date. As a result, the total Fe emissions from combustion averaged for 1960-2007 were estimated to be 5.3 Tg yr-1 (90% confidence of 2.3 to 12.1). Of these emissions, 1, 27 and 72% were emitted in particles 10 μm (PM> 10), respectively, compared to a total Fe emission from mineral dust of 41.0 Tg yr-1 in a log-normal distribution with a mass median diameter of 2.5 μm and a geometric standard deviation of 2. For combustion sources, different temporal trends were found in fine and medium-to-coarse particles, with a notable increase in Fe emissions in PM1 since 2000 due to an increase in Fe emission from motor vehicles (from 0.008 to 0.0103 Tg yr-1 in 2000 and 2007, respectively). These emissions have been introduced in a global 3-D transport model run at a spatial resolution of 0.94° latitude by 1.28° longitude to evaluate our estimation of Fe emissions. The modelled Fe concentrations as monthly means were compared with the monthly (57 sites) or daily (768 sites) measured concentrations at a total of 825 sampling stations. The deviation between modelled and observed Fe concentrations attached to aerosols at the surface was within a factor of 2 at most

  13. Sources, transport and deposition of iron in the global atmosphere

    Directory of Open Access Journals (Sweden)

    R. Wang

    2015-03-01

    Full Text Available Atmospheric deposition of iron (Fe plays an important role in controlling oceanic primary productivity. However, the sources of Fe in the atmosphere are not well understood. In particular, the combustion sources of Fe and their deposition over oceans are not accounted for in current biogeochemical models of the carbon cycle. Here we used a mass-balance method to estimate the emissions of Fe from the combustion of fossil fuels and biomass by accounting for the Fe contents in fuel and the partitioning of Fe during combustion. The emissions of Fe attached to aerosols from combustion sources were estimated by particle size, and their uncertainties were quantified by a Monte Carlo simulation. The emissions of Fe from mineral sources were estimated using the latest soil mineralogical database to date. As a result, the total Fe emissions from combustion averaged for 1960–2007 were estimated to be 5.1 Tg yr−1 (90% confidence of 2.2 to 11.5. Of these emissions, 2, 33 and 65% were emitted in particles 1, 1–10 μm (PM1−10, and >10 μm (PM>10, respectively, compared to total Fe emissions from mineral sources of 41.0 Tg yr−1. For combustion sources, different temporal trends were found in fine and medium-to-coarse particles, with a notable increase in Fe emissions in PM1 and PM1−10 since 2000 due to a rapid increase from motor vehicles. These emissions have been introduced in a global 3-D transport model run at a spatial resolution of of 0.94° latitude by 1.28° longitude to evaluate our estimation of Fe emissions. The modelled Fe concentrations were compared to measurements at 825 sampling stations. The deviation between modelled and observed Fe concentrations attached to aerosols at the surface was within a factor of two at most sampling stations, and the deviation was within a factor of 1.5 at sampling stations dominated by combustion sources. We analyzed the relative contribution of combustion sources to total Fe concentrations over

  14. Surface Modification by Atmospheric Pressure Plasma for Improved Bonding

    Science.gov (United States)

    Williams, Thomas Scott

    An atmospheric pressure plasma source operating at temperatures below 150?C and fed with 1.0-3.0 volume% oxygen in helium was used to activate the surfaces of the native oxide on silicon, carbon-fiber reinforced epoxy composite, stainless steel type 410, and aluminum alloy 2024. Helium and oxygen were passed through the plasma source, whereby ionization occurred and ˜10 16 cm-3 oxygen atoms, ˜1015 cm -3 ozone molecules and ˜1016 cm-3 metastable oxygen molecules (O21Deltag) were generated. The plasma afterglow was directed onto the substrate material located 4 mm downstream. Surface properties of the plasma treated materials have been investigated using water contact angle (WCA), atomic force microscopy (AFM), infrared spectroscopy (IR), and x-ray photoelectron spectroscopy (XPS). The work presented herein establishes atmospheric-pressure plasma as a surface preparation technique that is well suited for surface activation and enhanced adhesive bond strength in a variety of materials. Atmospheric plasma activation presents an environmentally friendly alternative to wet chemical and abrasive methods of surface preparation. Attenuated total internal reflection infrared spectroscopy was used to study the aging mechanism of the native oxide on silicon. During storage at ambient conditions, the water contact angle of a clean surface increased from composite, stainless steel type 410, and aluminum alloy 2024 was demonstrated with the atmospheric pressure helium-oxygen plasma. All surfaces studied were converted from a hydrophobic state with a water contact angle of 65° to 80° into a hydrophilic state with a water contact angle between 20° and 40° within 5 seconds of plasma exposure. X-ray photoelectron spectroscopy confirmed that the carbon atoms on the carbon-fiber/epoxy composite were oxidized, yielding 17 atom% carboxylic acid groups, 10% ketones or aldehydes and 9% alcohols. Analysis of stainless steel and aluminum by XPS illustrate oxidation of the metal

  15. Stress control of silicon nitride films deposited by plasma enhanced chemical vapor deposition

    Science.gov (United States)

    Li, Dong-ling; Feng, Xiao-fei; Wen, Zhi-yu; Shang, Zheng-guo; She, Yin

    2016-07-01

    Stress controllable silicon nitride (SiNx) films deposited by plasma enhanced chemical vapor deposition (PECVD) are reported. Low stress SiNx films were deposited in both high frequency (HF) mode and dual frequency (HF/LF) mode. By optimizing process parameters, stress free (-0.27 MPa) SiNx films were obtained with the deposition rate of 45.5 nm/min and the refractive index of 2.06. Furthermore, at HF/LF mode, the stress is significantly influenced by LF ratio and LF power, and can be controlled to be 10 MPa with the LF ratio of 17% and LF power of 150 W. However, LF power has a little effect on the deposition rate due to the interaction between HF power and LF power. The deposited SiNx films have good mechanical and optical properties, low deposition temperature and controllable stress, and can be widely used in integrated circuit (IC), micro-electro-mechanical systems (MEMS) and bio-MEMS.

  16. Imbalanced atmospheric nitrogen and phosphorus depositions in China: Implications for nutrient limitation

    Science.gov (United States)

    Zhu, Jianxing; Wang, Qiufeng; He, Nianpeng; Smith, Melinda D.; Elser, James J.; Du, Jiaqiang; Yuan, Guofu; Yu, Guirui; Yu, Qiang

    2016-06-01

    Atmospheric wet nitrogen (N) and phosphorus (P) depositions are important sources of bioavailable N and P, and the input of N and P and their ratios significantly influences nutrient availability and balance in terrestrial as well as aquatic ecosystems. Here we monitored atmospheric P depositions by measuring monthly dissolved P concentration in rainfall at 41 field stations in China. Average deposition fluxes of N and P were 13.69 ± 8.69 kg N ha-1 a-1 (our previous study) and 0.21 ± 0.17 kg P ha-1 a-1, respectively. Central and southern China had higher N and P deposition rates than northwest China, northeast China, Inner Mongolia, or Qinghai-Tibet. Atmospheric N and P depositions showed strong seasonal patterns and were dependent upon seasonal precipitation. Fertilizer and energy consumption were significantly correlated with N deposition but less correlated with P deposition. The N:P ratios of atmospheric wet deposition (with the average of 77 ± 40, by mass) were negatively correlated with current soil N:P ratios in different ecological regions, suggesting that the imbalanced atmospheric N and P deposition will alter nutrient availability and strengthen P limitation, which may further influence the structure and function of terrestrial ecosystems. The findings provide the assessments of both wet N and P deposition and their N:P ratio across China and indicate potential for strong impacts of atmospheric deposition on broad range of terrestrial ecosystems.

  17. The investigation of atmospheric deposition distribution of organochlorine pesticides (OCPs) in Turkey

    Science.gov (United States)

    Cindoruk, S. Sıddık; Tasdemir, Yücel

    2014-04-01

    Atmospheric deposition is a significant pollution source leading to contamination of remote and clean sites, surface waters and soils. Since persistent organic pollutants (POPs) stay in atmosphere without any degradation, they can be transported and deposited to clean surfaces. Organochlorine pesticides are an important group of POPs which have toxic and harmful effects to living organisms and environment. Therefore, atmospheric deposition levels and characteristics are of importance to determine the pollution quantity of water and soil surfaces in terms of POPs. This study reports the distribution quantities of atmospheric deposition including bulk, dry, wet and air-water exchange of particle and gas phase OCPs as a result of 1-year sampling campaign. Atmospheric deposition distribution showed that the main mechanism for OCPs deposition is wet processes with percentage of 69 of total deposition. OCP compounds' deposition varied according to atmospheric concentration and deposition mechanism. HCH compounds were dominant pesticide species for all deposition mechanisms. HCH deposition constituted the 65% of Σ10OCPs.

  18. Investigations on the Nature of Ceramic Deposits in Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    He, W.; Mauer, G.; Gindrat, M.; Wäger, R.; Vaßen, R.

    2017-01-01

    In Plasma Spray-Physical Vapor Deposition (PS-PVD) process, major fractions of the feedstock powder can be evaporated so that coatings are deposited mainly from the vapor phase. In this work, Computational Fluid Dynamics (CFD) results indicate that such evaporation occurs significantly in the plasma torch nozzle and even nucleation and condensation of zirconia is highly possible there. Experimental work has been performed to investigate the nature of the deposits in the PS-PVD process, in particular coatings from condensate vapor and nano-sized clusters produced at two spraying distances of 1000 mm and 400 mm. At long spraying distance, columns in the coatings have pyramidal tops and very sharp faceted microstructures. When the spraying distance is reduced to 400 mm, the tops of columns become relatively flat and a faceted structure is not recognizable. XRD patterns show obvious preferred orientations of (110) and (002) in the coatings sprayed at 400 mm but only limited texture in the coatings sprayed at 1000 mm. Meanwhile, a non-line of sight coating was also investigated, which gives an example for pure vapor deposition. Based on these analyses, a vapor and cluster depositions are suggested to further explain the formation mechanisms of high-quality columnar-structured PS-PVD thermal barrier coatings which have already shown excellent performance in cyclic lifetime test.

  19. Modeling and mapping of atmospheric mercury deposition in adirondack park, new york.

    Directory of Open Access Journals (Sweden)

    Xue Yu

    Full Text Available The Adirondacks of New York State, USA is a region that is sensitive to atmospheric mercury (Hg deposition. In this study, we estimated atmospheric Hg deposition to the Adirondacks using a new scheme that combined numerical modeling and limited experimental data. The majority of the land cover in the Adirondacks is forested with 47% of the total area deciduous, 20% coniferous and 10% mixed. We used litterfall plus throughfall deposition as the total atmospheric Hg deposition to coniferous and deciduous forests during the leaf-on period, and wet Hg deposition plus modeled atmospheric dry Hg deposition as the total Hg deposition to the deciduous forest during the leaf-off period and for the non-forested areas year-around. To estimate atmospheric dry Hg deposition we used the Big Leaf model. The average atmospheric Hg deposition to the Adirondacks was estimated as 17.4 [Formula: see text]g m[Formula: see text] yr[Formula: see text] with a range of -3.7-46.0 [Formula: see text]g m[Formula: see text] yr[Formula: see text]. Atmospheric Hg dry deposition (370 kg yr[Formula: see text] was found to be more important than wet deposition (210 kg yr[Formula: see text] to the entire Adirondacks (2.4 million ha. The spatial pattern showed a large variation in atmospheric Hg deposition with scattered areas in the eastern Adirondacks having total Hg deposition greater than 30 μg m(-2 yr(-1, while the southwestern and the northern areas received Hg deposition ranging from 25-30 μg m(-2 yr(-1.

  20. Diagnostics of atmospheric pressure capillary DBD oxygen plasma jet

    CERN Document Server

    Roy, N C; Pramanik, B K

    2015-01-01

    Atmospheric pressure capillary dielectric barrier oxygen discharge plasma jet is developed to generate non-thermal plasma using unipolar positive pulse power supply. Both optical and electrical techniques are used to investigate the characteristics of the produced plasma as function of applied voltage and gas flow rate. Analytical results obtained from the optical emission spectroscopic data reveal the gas temperature, rotational temperature, excitation temperature and electron density. Gas temperature and rotational temperature are found to decrease with increasing oxygen flow rate but increase linearly with applied voltage. It is exposed that the electron density is boosting up with enhanced applied voltage and oxygen flow rate, while the electron excitation temperature is reducing with rising oxygen flow rate. Electrical characterization demonstrates that the discharge frequency is falling with flow rate but increasing with voltage. The produced plasma is applied preliminarily to study the inactivation yie...

  1. Organic nanocones fabricated by atmospheric plasma polymerization for immobilizing bioprobes

    Energy Technology Data Exchange (ETDEWEB)

    Chen Guangliang; Chen Wenxing [Key Laboratory of Advanced Textile Materials and Manufacturing Technology, Ministry of Education, Zhejiang Sci-Tech University, Hangzhou 310018 (China); Chen Shihua; Zhou Mingyan [Department of Civil and Environmental Engineering, Rensselaer Polytechnic Institute, 110 8th Street, Troy, NY 12180 (United States); Yang Size [Beijing National Laboratory for Condensed Matter Physics, Institute of Physics, Chinese Academy of Sciences, Beijing 100080 (China)], E-mail: glchen@zstu.edu.cn

    2008-02-20

    Inspired by the formation process of natural thundershowers, we fabricated an organic nanocone matrix-like bamboo-shoot by using atmospheric plasma polymerization in the absence of any catalyst or template. The discharging characteristics affected the nanocone shape and distribution in an obvious way. The nanocones prepared by helium (He) plasma were about 120 nm in diameter and 80 nm high. The nanostructured surface acted as an adhesion layer immobilizing DNA probes for DNA hybridization assay. The density of NH{sub 2}-DNA probes prepared by He, argon (Ar) and nitrogen (N{sub 2}) plasma was confirmed by the dyed oligonucleotide and was found to be 3.2, 1.0 and 0.6 pM cm{sup -2}, respectively. Each nanocone prepared by helium plasma contains nearly 4 x 10{sup 2} amine groups.

  2. Atmospheric nitrogen deposition in world biodiversity hotspots: the need for a greater global perspective in assessing N deposition impacts

    NARCIS (Netherlands)

    Phoenix, G.K.; Hicks, W.K.; Cinderby, S.; Kuylenstierna, J.C.I.; Stock, W.D.; Dentener, F.J.; Giller, K.E.; Austin, A.T.; Lefroy, R.D.B.; Gimeno, B.S.; Ashmore, M.R.; Ineson, P.

    2006-01-01

    Increased atmospheric nitrogen (N) deposition is known to reduce plant diversity in natural and semi-natural ecosystems, yet our understanding of these impacts comes almost entirely from studies in northern Europe and North America. Currently, we lack an understanding of the threat of N deposition t

  3. Diagnostic for Plasma Enhanced Chemical Vapor Deposition and Etch Systems

    Science.gov (United States)

    Cappelli, Mark A.

    1999-01-01

    In order to meet NASA's requirements for the rapid development and validation of future generation electronic devices as well as associated materials and processes, enabling technologies ion the processing of semiconductor materials arising from understanding etch chemistries are being developed through a research collaboration between Stanford University and NASA-Ames Research Center, Although a great deal of laboratory-scale research has been performed on many of materials processing plasmas, little is known about the gas-phase and surface chemical reactions that are critical in many etch and deposition processes, and how these reactions are influenced by the variation in operating conditions. In addition, many plasma-based processes suffer from stability and reliability problems leading to a compromise in performance and a potentially increased cost for the semiconductor manufacturing industry. Such a lack of understanding has hindered the development of process models that can aid in the scaling and improvement of plasma etch and deposition systems. The research described involves the study of plasmas used in semiconductor processes. An inductively coupled plasma (ICP) source in place of the standard upper electrode assembly of the Gaseous Electronics Conference (GEC) radio-frequency (RF) Reference Cell is used to investigate the discharge characteristics and chemistries. This ICP source generates plasmas with higher electron densities (approximately 10(exp 12)/cu cm) and lower operating pressures (approximately 7 mTorr) than obtainable with the original parallel-plate version of the GEC Cell. This expanded operating regime is more relevant to new generations of industrial plasma systems being used by the microelectronics industry. The motivation for this study is to develop an understanding of the physical phenomena involved in plasma processing and to measure much needed fundamental parameters, such as gas-phase and surface reaction rates. species

  4. High T(sub c) superconductors fabricated by plasma aerosol mist deposition technique

    Science.gov (United States)

    Wang, X. W.; Vuong, K. D.; Leone, A.; Shen, C. Q.; Williams, J.; Coy, M.

    1995-01-01

    We report new results on high T(sub c) superconductors fabricated by a plasma aerosol mist deposition technique, in atmospheric environment. Materials fabricated are YBaCuO, BiPbSrCaCuO, BaCaCuO precursor films for TlBaCaCuO, and other buffers such as YSZ. Depending on processing conditions, sizes of crystallites and/or particles are between dozens of nano-meters and several micrometers. Superconductive properties and other material characteristics can also be tailored.

  5. Synthesis of carbon nanotube array using corona discharge plasma-enhanced chemical vapor deposition

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    A corona discharge plasma-enhanced chemical vapor deposition with the features of atmospheric pressure and low temperature has been developed to synthesize the carbon nanotube array. The array was synthesized from methane and hydrogen mixture in anodic aluminum oxide template channels in that cobalt was electrodeposited at the bottom. The characterization results by the scanning electron microscopy, transmission electron microscopy, energy dispersive X-ray spectroscopy and Raman spectroscopy indicate that the array consists of carbon nanotubes with the diameter of about 40 nm and the length of more than 4 -m, and the carbon nanotubes are mainly restrained within the channels of templates.

  6. Oxygen Plasma Treatment of Rubber Surface by the Atmospheric Pressure Cold Plasma Torch

    DEFF Research Database (Denmark)

    Lee, Bong-ju; Kusano, Yukihiro; Kato, Nobuko

    1997-01-01

    A new application of the atmospheric cold plasma torch has been investigated. Namely, the surface treatment of an air-exposed vulcanized rubber compound. The effect of plasma treatment was evaluated by the bondability of the treated rubber compound with another rubber compound using a polyurethane...... adhesive. The adhesion property was improved by treatment of the rubber compound with plasma containing oxygen radicals. Physical and chemical changes of the rubber surface as a result of the plasma treatment were analyzed by field emission scanning electron microscopy (FE-SEM) and fourier transform...

  7. Plasma Disinfection and the Deterioration of Surgical Tools at Atmospheric Pressure Plasma

    Science.gov (United States)

    Zaaba, Siti Khadijah; Akitsu, Tetsuya; Ohkawa, Hiroshi; Katayama-Hirayama, Keiko; Tsuji, Masao; Shimizu, Naohiro; Imanishi, Yuichirou

    The purpose of this paper is to present and compare disinfection effect of plasma by means of Atmospheric Pressure Glow plasma and streamer discharge. Geobacillus stearothermophilus was used as biological indicator for disinfection process. The effect of blades after irradiated in plasma was also studied by SEM analysis. It was found that the disinfection process was effective when the cylindrical configuration was applied. Carbon steel blade was also found to be deteriorated after immersed in plasma irradiation. Results indicate that disinfection can be achieved and at the same time deteriorations of the tools were observed.

  8. Thin film deposition at atmospheric pressure using dielectric barrier discharges: Advances on three-dimensional porous substrates and functional coatings

    Science.gov (United States)

    Fanelli, Fiorenza; Bosso, Piera; Mastrangelo, Anna Maria; Fracassi, Francesco

    2016-07-01

    Surface processing of materials by atmospheric pressure dielectric barrier discharges (DBDs) has experienced significant growth in recent years. Considerable research efforts have been directed for instance to develop a large variety of processes which exploit different DBD electrode geometries for the direct and remote deposition of thin films from precursors in gas, vapor and aerosol form. This article briefly reviews our recent progress in thin film deposition by DBDs with particular focus on process optimization. The following examples are provided: (i) the plasma-enhanced chemical vapor deposition of thin films on an open-cell foam accomplished by igniting the DBD throughout the entire three-dimensional (3D) porous structure of the substrate, (ii) the preparation of hybrid organic/inorganic nanocomposite coatings using an aerosol-assisted process, (iii) the DBD jet deposition of coatings containing carboxylic acid groups and the improvement of their chemical and morphological stability upon immersion in water.

  9. Atmospheric-pressure glow plasma synthesis of plasmonic and photoluminescent zinc oxide nanocrystals

    Science.gov (United States)

    Bilik, N.; Greenberg, B. L.; Yang, J.; Aydil, E. S.; Kortshagen, U. R.

    2016-06-01

    In this paper, we present a large-volume (non-micro) atmospheric pressure glow plasma capable of rapid, large-scale zinc oxide nanocrystal synthesis and deposition (up to 400 μg/min), whereas in the majority of the literature, nanoparticles are synthesized using micro-scale or filamentary plasmas. The reactor is an RF dielectric barrier discharge with a non-uniform gap spacing. This design encourages pre-ionization during the plasma breakdown, making the discharge uniform over a large volume. The produced zinc oxide nanocrystals typically have diameters ranging from 4 to 15 nm and exhibit photoluminescence at ≈550 nm and localized surface plasmon resonance at ≈1900 cm-1 due to oxygen vacancies. The particle size can be tuned to a degree by varying the gas temperature and the precursor mixing ratio.

  10. Surface modification of cellulosic substrates via atmospheric pressure plasma polymerization of acrylic acid: Structure and properties

    Science.gov (United States)

    Garcia-Torres, Jose; Sylla, Dioulde; Molina, Laura; Crespo, Eulalia; Mota, Jordi; Bautista, Llorenç

    2014-06-01

    Surface chemical modification of cellulose-based substrates has been carried out by atmospheric pressure plasma enhanced chemical vapor deposition (AP-PECVD) of acrylic acid. The structure/properties relationship of the samples was studied as a function of the plasma experimental conditions. Acrylic acid monomer/helium ratio and treatment speed clearly influences the wettability properties of the paper substrate: advancing contact angle values were reduced to the half if compare to non-treated paper. Surface morphology of the films did not greatly vary at short polymerization times but fibers were covered by a poly(acrylic acid) film at longer times. FTIR and XPS techniques allowed detecting the retention of carboxylic acid groups/moieties. The possibility to quickly design architectures with tunable carboxylic functions by modifying the plasma processing parameters is shown.

  11. Atmospheric-pressure glow plasma synthesis of plasmonic and photoluminescent zinc oxide nanocrystals

    Energy Technology Data Exchange (ETDEWEB)

    Bilik, N., E-mail: bilik006@umn.edu, E-mail: kortshagen@umn.edu; Greenberg, B. L.; Yang, J.; Kortshagen, U. R., E-mail: bilik006@umn.edu, E-mail: kortshagen@umn.edu [Department of Mechanical Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States); Aydil, E. S. [Department of Chemical Engineering, University of Minnesota, Minneapolis, Minnesota 55455 (United States)

    2016-06-28

    In this paper, we present a large-volume (non-micro) atmospheric pressure glow plasma capable of rapid, large-scale zinc oxide nanocrystal synthesis and deposition (up to 400 μg/min), whereas in the majority of the literature, nanoparticles are synthesized using micro-scale or filamentary plasmas. The reactor is an RF dielectric barrier discharge with a non-uniform gap spacing. This design encourages pre-ionization during the plasma breakdown, making the discharge uniform over a large volume. The produced zinc oxide nanocrystals typically have diameters ranging from 4 to 15 nm and exhibit photoluminescence at ≈550 nm and localized surface plasmon resonance at ≈1900 cm{sup −1} due to oxygen vacancies. The particle size can be tuned to a degree by varying the gas temperature and the precursor mixing ratio.

  12. Bacteria Inactivation Using DBD Plasma Jet in Atmospheric Pressure Argon

    Institute of Scientific and Technical Information of China (English)

    XU Guimin; ZHANG Guanjun; SHI Xingmin; MA Yue; WANG Ning; LI Yuan

    2009-01-01

    A coaxial dielectric barrier discharge plasma jet Was designed,which can be operated in atmospheric pressure argon under an intermediate frequency sinusoidal resonant power supply,and an atmospheric pressure glow-like discharge Was achieved.Two kinds of typical bacteria,i.e.,the Staphylococcus aureus(S.aurens)and Escherichia coil(E.coil),were employed to study the bacterial inactivation mechanism by means of the non-thermal plasma.The killing log value (KLV)of S.aureus reached up to 5.38 with a treatment time of 90 s and that of E.coil up to 5.36 with 60 s,respectively.According to the argon emission spectra of the plasma jet and the scanning electron microscope (SEM) images of the two bacteria before and after the plasma treatment.it is concluded that the reactive species in the argon plasma played a major role in the bacterial inactivation,while the heat,electric field and UV photons had little effect.

  13. Microwave heating systems for atmospheric pressure: Nonequilibrium plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Guest, G.E.; Dandl, R.A. (AMPC, Inc., Carlsbad, CA (USA))

    1989-03-01

    Nonequilibrium plasma-chemical processing is attracting increasing interest because of the possibility of creating mixtures of active species that would not be available in thermal equilibrium. For significant throughput of reactants it would be advantageous to create nonequilibrium plasmas in large volumes of atmospheric-pressure mixtures of gases. Techniques for accomplishing this are very limited at present. Here they describe a novel microwave approach to creating nonequilibrium plasmas in large volumes of atmospheric-pressure gases using pulses of microwave radiation with very high peak power that are focused by quasi-optical techniques at one or more points in the interior of the reaction chamber. A new type of microwave source, the Plasma Electron Microwave Source (PEMS), is able to produce the require power levels by storing cw microwave power in a mirror-confined, relativistic-electron plasma and periodically transforming a fraction of that stored energy into intense microwave pulses. This approach avoids many of the limitations inherent in resonant cavity approaches and is expected to permit ultrahigh purity discharges to be produced.

  14. Recent Advances in Atmospheric Vapor-Phase Deposition of Transparent and Conductive Zinc Oxide

    NARCIS (Netherlands)

    Illiberi, A.; Poodt, P.; Roozeboom, F.

    2014-01-01

    The industrial need for high-throughput and low-cost ZnO deposition processes has triggered the development of atmospheric vapor-phase deposition techniques which can be easily applied to continuous, in-line manufacturing. While atmospheric CVD is a mature technology, new processes for the growth of

  15. Nutritional constraints in ombrotrophic Sphagnum plants under increasing atmospheric nitrogen deposition in Europe

    NARCIS (Netherlands)

    Bragazza, L.; Tahvanainen, T.; Kutnar, L.; Rydin, H.; Limpens, J.; Hajek, M.; Grosvernier, P.; Hansen, I.; Lacumin, P.; Gerdol, R.

    2004-01-01

    We studied the effects of increasing levels of atmospheric nitrogen (N) deposition on nutrient limitation of ombrotrophic Sphagnum plants. • Fifteen mires in 11 European countries were selected across a natural gradient of bulk atmospheric N deposition from 0.1 to 2 g/m2 year-1. Nutritional constrai

  16. Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

    Institute of Scientific and Technical Information of China (English)

    ZHANG Hao; ZHU Fengsen; TU Xin; BO Zheng; CEN Kefa; LI Xiaodong

    2016-01-01

    In this work,a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions.The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals,high speed photography,and optical emission spectroscopic diagnostics.Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g.,10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone,in this RGA system,a lower gas flow rate (e.g.,2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions.Two different motion patterns can be clearly observed in the N2 and air RGA plasmas.The time-resolved arc voltage signals show that three different arc dynamic modes,the arc restrike mode,takeover mode,and combined modes,can be clearly identified in the RGA plasmas.The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.

  17. Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

    Science.gov (United States)

    Zhang, Hao; Zhu, Fengsen; Tu, Xin; Bo, Zheng; Cen, Kefa; Li, Xiaodong

    2016-05-01

    In this work, a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals, high speed photography, and optical emission spectroscopic diagnostics. Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g., 10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone, in this RGA system, a lower gas flow rate (e.g., 2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions. Two different motion patterns can be clearly observed in the N2 and air RGA plasmas. The time-resolved arc voltage signals show that three different arc dynamic modes, the arc restrike mode, takeover mode, and combined modes, can be clearly identified in the RGA plasmas. The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate. supported by National Natural Science Foundation of China (No. 51576174), the Specialized Research Fund for the Doctoral Program of Higher Education of China (No. 20120101110099) and the Fundamental Research Funds for the Central Universities (No. 2015FZA4011)

  18. Cold Atmospheric Plasma Technology for Decontamination of Space Equipment

    Science.gov (United States)

    Thomas, Hubertus; Rettberg, Petra; Shimizu, Tetsuji; Thoma, Markus; Morfill, Gregor; Zimmermann, Julia; Müller, Meike; Semenov, Igor

    2016-07-01

    Cold atmospheric plasma (CAP) technology is very fast and effective in inactivation of all kinds of pathogens. It is used in hygiene and especially in medicine, since the plasma treatment can be applied to sensitive surfaces, like skin, too. In a first study to use CAP for the decontamination of space equipment we could show its potential as a quite promising alternative to the standard "dry heat" and H2O2 methods [Shimizu et al. Planetary and Space Science, 90, 60-71. (2014)]. In a follow-on study we continue the investigations to reach high application level of the technology. First, we redesign the actual setup to a plasma-gas circulation system, increasing the effectivity of inactivation and the sustainability. Additionally, we want to learn more about the plasma chemistry processes involved in the inactivation. Therefore, we perform detailed plasma and gas measurements and compare them to numerical simulations. The latter will finally be used to scale the decontamination system to sizes useful also for larger space equipment. Typical materials relevant for space equipment will be tested and investigated on surface material changes due to the plasma treatment. Additionally, it is planned to use electronic boards and compare their functionality before and after the CAP expose. We will give an overview on the status of the plasma decontamination project funded by the Bavarian Ministry of Economics.

  19. Review: Plasma-enhanced chemical vapor deposition of nanocrystalline diamond

    Directory of Open Access Journals (Sweden)

    Katsuyuki Okada

    2007-01-01

    Full Text Available Nanocrystalline diamond films have attracted considerable attention because they have a low coefficient of friction and a low electron emission threshold voltage. In this paper, the author reviews the plasma-enhanced chemical vapor deposition (PE-CVD of nanocrystalline diamond and mainly focuses on the growth of nanocrystalline diamond by low-pressure PE-CVD. Nanocrystalline diamond particles of 200–700 nm diameter have been prepared in a 13.56 MHz low-pressure inductively coupled CH4/CO/H2 plasma. The bonding state of carbon atoms was investigated by ultraviolet-excited Raman spectroscopy. Electron energy loss spectroscopy identified sp2-bonded carbons around the 20–50 nm subgrains of nanocrystalline diamond particles. Plasma diagnostics using a Langmuir probe and the comparison with plasma simulation are also reviewed. The electron energy distribution functions are discussed by considering different inelastic interaction channels between electrons and heavy particles in a molecular CH4/H2 plasma.

  20. Numerical simulation of chemical processes in atmospheric plasmas

    Institute of Scientific and Technical Information of China (English)

    Ouyang Jian-Ming; Guo Wei; Wang Long; Shao Fu-Qiu

    2004-01-01

    A model is built to study chemical processes in atmospheric plasmas at low altitude (high pressure) and at high altitude (low pressure). The plasma lifetime and the temporal evolution of the main charged species are presented.The electron number density does not strictly obey the exponential damping law in a long period. The heavy charged species are dominant at low altitude in comparison with the light species at high altitude. Some species of small amount in natural air play an important role in the processes.

  1. Plasma-induced Escape and Alterations of Planetary Atmospheres

    Science.gov (United States)

    Johnson, R. E.; Tucker, O. J.; Ewrin, J.; Cassidy, T. A.; Leblanc, F.

    2009-12-01

    The atmospheres of planets and planetary satellites are typically imbedded in space plasmas. Depending on the interaction with the induced or intrinsic fields energetic ions can have access to the thermosphere and the corona affecting their composition and thermal structure and causing loss to space. These processes are often lumped together as ‘atmospheric sputtering’ (Johnson 1994). In this talk I will review the results of simulations of the plasma bombardment at a number of solar system bodies and use those data to describe the effect on the upper atmosphere and on escape. Of considerable recent interest is the modeling of escape from Titan. Prior to Cassini’s tour of the Saturnian system, plasma-induced escape was suggested to be the dominant loss process, but recent models of enhanced thermal escape, often referred to as ‘slow hydrodynamic’ escape, have been suggested to lead to much larger Titan atmospheric loss rates (Strobel 2008; Cui et al. 2008). Such a process has been suggested to be active at some point in time on a number of solar system bodies. I will present hybrid fluid/ kinetic models of the upper atmosphere of certain bodies in order to test both the plasma-induced and thermal escape processes. Preliminary results suggest that the loss rates estimated using the ‘slow hydrodynamic’ escape process can be orders of magnitude too large. The implications for Mars, Titan and Pluto will be discussed. Background for this talk is contained in the following papers (Johnson 2004; 2009; Chaufray et al. 2007; Johnson et al. 2008; 2009; Tucker and Johnson 2009). References: Chaufray, J.Y., R. Modolo, F. Leblanc, G. Chanteur, R.E. Johnson, and J.G. Luhmann, Mars Solar Wind interaction: formation of the Martian corona and atmosphric loss to space, JGR 112, E09009, doi:10.1029/2007JE002915 (2007) Cui, J., Yelle, R. V., Volk, K. Distribution and escape of molecular hydrogen in Titan's thermosphere and exosphere. J. Geophys. Res. 113, doi:10

  2. Plasma deposited diamond-like carbon films for large neutralarrays

    Energy Technology Data Exchange (ETDEWEB)

    Brown, I.G.; Blakely, E.A.; Bjornstad, K.A.; Galvin, J.E.; Monteiro, O.R.; Sangyuenyongpipat, S.

    2004-07-15

    To understand how large systems of neurons communicate, we need to develop methods for growing patterned networks of large numbers of neurons. We have found that diamond-like carbon thin films formed by energetic deposition from a filtered vacuum arc carbon plasma can serve as ''neuron friendly'' substrates for the growth of large neural arrays. Lithographic masks can be used to form patterns of diamond-like carbon, and regions of selective neuronal attachment can form patterned neural arrays. In the work described here, we used glass microscope slides as substrates on which diamond-like carbon was deposited. PC-12 rat neurons were then cultured on the treated substrates and cell growth monitored. Neuron growth showed excellent contrast, with prolific growth on the treated surfaces and very low growth on the untreated surfaces. Here we describe the vacuum arc plasma deposition technique employed, and summarize results demonstrating that the approach can be used to form large patterns of neurons.

  3. Use of the lichen Xanthoria mandschurica in monitoring atmospheric elemental deposition in the Taihang Mountains, Hebei, China

    Science.gov (United States)

    Liu, Hua-Jie; Zhao, Liang-Cheng; Fang, Shi-Bo; Liu, Si-Wa; Hu, Jian-Sen; Wang, Lei; Liu, Xiao-Di; Wu, Qing-Feng

    2016-04-01

    Air pollution is a major concern in China. Lichens are a useful biomonitor for atmospheric elemental deposition but have rarely been used in North China. The aim of this study was to investigate the atmospheric depositions of 30 trace elements (Al, Ba, Ca, Cd, Ce, Co, Cr, Cs, Cu, Fe, K, La, Mg, Mn, Mo, Na, Ni, P, Pb, Rb, Sb, Sc, Sm, Sr, Tb, Th, Ti, Tl, V and Zn) in a region of the Taihang Mountains, Hebei Province, China using lichens as biomonitors. Epilithic foliose lichen Xanthoria mandschurica was sampled from 21 sites and analyzed using inductively coupled plasma mass spectrometry (ICP-MS). The results show that 1) eight elements (Cd, Cr, Cu, Mo, P, Pb, Sb and Zn) are of atmospheric origin and are highly influenced by the atmospheric transportation from the North China Plain, as well as local mining activities, while 2) the remaining 22 elements are primarily of crustal origin, the concentration of which has been enhanced by local mining and quarrying activities. These results clearly validate the applicability of lichens in biomonitoring of atmospheric elemental deposition and demonstrate the spatial pattern for air pollution in the region.

  4. CMAS Interactions with Advanced Environmental Barrier Coatings Deposited via Plasma Spray- Physical Vapor Deposition

    Science.gov (United States)

    Harder, B. J.; Wiesner, V. L.; Zhu, D.; Johnson, N. S.

    2017-01-01

    Materials for advanced turbine engines are expected to have temperature capabilities in the range of 1370-1500C. At these temperatures the ingestion of sand and dust particulate can result in the formation of corrosive glass deposits referred to as CMAS. The presence of this glass can both thermomechanically and thermochemically significantly degrade protective coatings on metallic and ceramic components. Plasma Spray- Physical Vapor Deposition (PS-PVD) was used to deposit advanced environmental barrier coating (EBC) systems for investigation on their interaction with CMAS compositions. Coatings were exposed to CMAS and furnace tested in air from 1 to 50 hours at temperatures ranging from 1200-1500C. Coating composition and crystal structure were tracked with X-ray diffraction and microstructure with electron microscopy.

  5. Status and trend of atmospheric deposition chemistry at the CONECOFOR plots, 1998-2005

    Directory of Open Access Journals (Sweden)

    Aldo Marchetto

    2013-11-01

    Full Text Available Ion deposition in the open field and under the canopy was monitored in 13 CONECOFOR plots during 1998-2005. In spite of the remote location of most plots, atmospheric deposition carries considerable amounts of anthropogenic ions (sulphate, nitrate and ammonium. Deposition acidity is buffered by the deposition of base cations, partially due to the long-range transport of Saharan dust. In the study period, sulphate deposition and deposition acidity significantly decreased, because of the decrease in sulphur dioxide emissions in Europe, while nitrate and ammonia deposition did not show a clear temporal pattern.

  6. A microwave plasma source for VUV atmospheric photochemistry

    OpenAIRE

    Tigrine, Sarah; Carrasco, Nathalie; Vettier, Ludovic; Cernogora, Guy

    2017-01-01

    International audience; Microwave plasma discharges working at low pressure are nowadays a well-developed technique mainly used to provide radiations at different wavelengths. The aim of this work is to show that those discharges are an efficient windowless VUV photon source for planetary atmospheric photochemistry experiments. To do this, we use a surfatron-type discharge with a neon gas flow in the mbar pressure range coupled to a photochemical reactor. Working in the VUV range allows to fo...

  7. Deposition of fuel pellets injected into tokamak plasmas

    Energy Technology Data Exchange (ETDEWEB)

    Baylor, L.R.; Jernigan, T.C. [Oak Ridge National Lab., TN (United States); Hsieh, C. [General Atomics, San Diego, CA (United States)

    1998-06-01

    Pellet injection has been used on tokamak devices in a number of experiments to provide plasma fueling and density profile control. The mass deposition of these fuel pellets defined as the change in density profile caused by the pellet, has been found to show an outward displacement of the ablated material from that expected by mapping the theoretical ablation rate onto the flux surfaces. This suggests that fast transport of the pellet ablatant occurs during the flow along field lines that may be driven by {del}B drift effects. A comparison of the deposition of pellets from different machines shows similar behavior. Initial results from alternative injection locations designed to take advantage of the outward ablatant drift is presented.

  8. In situ chitosan gelation initiated by atmospheric plasma treatment.

    Science.gov (United States)

    Molina, R; Jovancic, P; Vilchez, S; Tzanov, T; Solans, C

    2014-03-15

    This work reports on the feasibility of atmospheric dielectric barrier discharge (DBD) plasma as a novel synthetic pathway for the liquid phase gelation of chitosan. The DBD plasma chitosan gelation process did not significantly alter the chemical structure of the biopolymer as confirmed by FTIR study. However, the oxidation processes and local heating effect associated with the solvent evaporation during the plasma treatment could provoke both reaction of chitosan degradation and the cleavage of β-1-4-glycosidic linkages with the concomitant generation of aldehyde groups able to crosslink via Schiff-base with amino groups from other chitosan molecules. Shear viscosity measurements suggested the formation of chitosan fragments of lower molecular weight after the plasma treatment of 1% (w/v) chitosan and fragments of higher molecular weight after the plasma treatment of 2% (w/v) chitosan. The crosslinking density of hydrogels generated during the in situ DBD plasma chitosan gelation process increased as a function of the treatment time and concentration of chitosan. As of consequence of the increase of the cross-linking density, the equilibrium swelling ratio and water content decreased significantly.

  9. Atmospheric pressure plasma assisted calcination of composite submicron fibers

    Science.gov (United States)

    Medvecká, Veronika; Kováčik, Dušan; Tučeková, Zlata; Zahoranová, Anna; Černák, Mirko

    2016-08-01

    The plasma assisted calcination of composite organic/inorganic submicron fibers for the preparation of inorganic fibers in submicron scale was studied. Aluminium butoxide/polyvinylpyrrolidone fibers prepared by electrospinning were treated using low-temperature plasma generated by special type of dielectric barrier discharge, so called diffuse coplanar surface barrier discharge (DCSBD) at atmospheric pressure in ambient air, synthetic air, oxygen and nitrogen. Effect of plasma treatment on base polymer removal was investigated by using Attenuated total reflectance - Fourier transform infrared (ATR-FTIR) spectroscopy. Influence of working gas on the base polymer reduction was studied by energy-dispersive X-ray spectroscopy (EDX) and CHNS elemental analysis. Changes in fibers morphology were observed by scanning electron microscopy (SEM). High efficiency of organic template removal without any degradation of fibers was observed after plasma treatment in ambient air. Due to the low-temperature approach and short exposure time, the plasma assisted calcination is a promising alternative to the conventional thermal calcination. Contribution to the topical issue "6th Central European Symposium on Plasma Chemistry (CESPC-6)", edited by Nicolas Gherardi, Ester Marotta and Cristina Paradisi

  10. Nanostructured yttria stabilized zirconia coatings deposited by air plasma spraying

    Institute of Scientific and Technical Information of China (English)

    ZHOU Hong; LI Fei; HE Bo; WANG Jun; SUN Bao-de

    2007-01-01

    Nanostructured yttria partially stabilized zirconia coatings were deposited by air plasma spraying with reconstituted nanosized powder. The microstructures and phase compositions of the powder and the as-sprayed nanostructured coatings were characterized by transmission electron microscopy(TEM), scanning electron microscopy(SEM) and X-ray diffraction(XRD). The results demonstrate that the microstructure of as-sprayed nanostructured zirconia coating exhibits a unique tri-modal distribution including the initial nanostructure of the powder, equiaxed grains and columnar grains. Air plasma sprayed nanostructured zirconia coatings consist of only the nontransformable tetragonal phase, though the reconstituted nanostructured powder shows the presence of the monoclinic, the tetragonal and the cubic phases. The mean grain size of the coating is about 42 nm.

  11. Formation of carbon deposits from coal in an arc plasma

    Energy Technology Data Exchange (ETDEWEB)

    Wang, B.; Tian, Y.; Zhang, Y.; Zhu, S.; Lu, Y.; Zhang, Y.; Xie, K. [Taiyuan University of Technology, Taiyuan (China)

    2007-07-01

    The issue of deposited carbon (DC) on a reactor wall during the production of acetylene by the coal/arc plasma process is a potential obstacle for the industrialization process. The formation mechanism of DC is very difficult to reveal because the high complexity of coal and the volatile matter. Combining with quenching technique, the methane, liquid petroleum gas and benzene were employed as the model materials to roughly act as the light gas, chain and aromatic subcomponents of volatile matter, and then the reasonable formation mechanism of DC was subtly speculated accordingly.

  12. Temporal modulation of plasma species in atmospheric dielectric barrier discharges

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Aijun; Wang, Xiaohua, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn; Liu, Dingxin; Rong, Mingzhe, E-mail: xhw@mail.xjtu.edu.cn, E-mail: mzrong@mail.xjtu.edu.cn [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Kong, Michael G. [Centre for Plasma Biomedicine, State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Frank Reidy Research Center for Bioelectrics, Department of Electrical and Computer Engineering, Old Dominion University, Virginia 23508 (United States); Department of Electrical and Computer Engineering, Old Dominion University, Norfolk, Virginia 23529 (United States)

    2014-07-15

    The atmospheric pressure dielectric barrier discharge in helium is a pulsed discharge in nature and the moment of maximum species densities is almost consistent with peak discharge current density. In this paper, a one-dimensional fluid model is used to investigate the temporal structure of plasma species in an atmospheric He-N{sub 2} dielectric barrier discharge (DBD). It is demonstrated that there exist microsecond delays of the moments of the maximum electron and ion densities from the peak of discharge current density. These time delays are caused by a competition between the electron impact and Penning ionizations, modulated by the N{sub 2} level in the plasma-forming gas. Besides, significant electron wall losses lead to the DBD being more positively charged and, with a distinct temporal separation in the peak electron and cation densities, the plasma is characterized with repetitive bursts of net positive charges. The temporal details of ionic and reactive plasma species may provide a new idea for some biological processes.

  13. Non-thermal atmospheric pressure plasma jet and its application for polymer treatment

    OpenAIRE

    Sarani, Abdollah

    2010-01-01

    Non-thermal atmospheric pressure plasma jet is a suitable source for polymer treatment. The main characteristic of this plasma jet is the remote operation and its scalable dimension, thus, allowing local treatment of 3D surfaces. In this work an atmospheric pressure DBD plasma jet has been constructed and the application of the plasma jet for polymer treatment is investigated.

  14. Synthesis of multicomponent metallic layers during impulse plasma deposition

    Directory of Open Access Journals (Sweden)

    Nowakowska-Langier Katarzyna

    2015-12-01

    Full Text Available Pulsed plasma in the impulse plasma deposition (IPD synthesis is generated in a coaxial accelerator by strong periodic electrical pulses, and it is distributed in a form of energetic plasma packets. A nearly complete ionization of gas, in these conditions of plasma generation, favors the nucleation of new phase of ions and synthesis of metastable materials in a form of coatings which are characterized by amorphous and/or nanocrystalline structure. In this work, the Fe–Cu alloy, which is immiscible in the state of equilibrium, was selected as a model system to study the possibility of formation of a non-equilibrium phase during the IPD synthesis. Structural characterization of the layers was done by means of X-ray diffraction and conversion-electron Mössbauer spectroscopy. It was found that supersaturated solid solutions were created as a result of mixing and/or alloying effects between the layer components delivered to the substrate independently and separately in time. Therefore, the solubility in the Fe–Cu system was largely extended in relation to the equilibrium conditions, as described by the equilibrium phase diagram in the solid state.

  15. Atmospherically deposited trace metals from bulk mineral concentrate port operations.

    Science.gov (United States)

    Taylor, Mark Patrick

    2015-05-15

    Although metal exposures in the environment have declined over the last two decades, certain activities and locations still present a risk of harm to human health. This study examines environmental dust metal and metalloid hazards (arsenic, cadmium, lead and nickel) associated with bulk mineral transport, loading and unloading port operations in public locations and children's playgrounds in the inner city of Townsville, northern Queensland. The mean increase in lead on post-play hand wipes (965 μg/m(2)/day) across all sites was more than 10-times the mean pre-play loadings (95 μg/m(2)/day). Maximum loading values after a 10-minute play period were 3012 μg/m(2), more than seven times the goal of 400 μg/m(2) used by the Government of Western Australia (2011). Maximum daily nickel post-play hand loadings (404 μg/m(2)) were more than 26 times above the German Federal Immission Control Act 2002 annual benchmark of 15 μg/m(2)/day. Repeat sampling over the 5-day study period showed that hands and surfaces were re-contaminated daily from the deposition of metal-rich atmospheric dusts. Lead isotopic composition analysis of dust wipes ((208)Pb/(207)Pb and (206)Pb/(207)Pb) showed that surface dust lead was similar to Mount Isa type ores, which are exported through the Port of Townsville. While dust metal contaminant loadings are lower than other mining and smelting towns in Australia, they exceeded national and international benchmarks for environmental quality. The lessons from this study are clear - even where operations are considered acceptable by managing authorities, targeted assessment and monitoring can be used to evaluate whether current management practices are truly best practice. Reassessment can identify opportunities for improvement and maximum environmental and human health protection.

  16. Atmospheric Sulfur Deposition for a Red Soil Broadleaf Forest in Southern China

    Institute of Scientific and Technical Information of China (English)

    XU Cheng-Kai; HU Zheng-Yi; CAI Zu-Cong; WANG Ti-Jian; HE Yuan-Qiu; CAO Zhi-Hong

    2004-01-01

    A two-year study in a typical red soil region of Southern China was conducted to determine 1) the dry deposition velocity (Vd) for SO2 and particulate SO2 4- above a broadleaf forest, and 2) atmospheric sulfur fluxes so as to estimate the contribution of various fractions in the total. Using a resistance model based on continuous hourly meteorological data, atmospheric dry sulfur deposition in a forest was estimated according to Vd and concentrations of both atmospheric SO2 and particulate SO24-. Meanwhile, wet S deposition was estimated based on rainfall and sulfate concentrations in the rainwater. Results showed that about 99% of the dry sulfur deposition flux in the forest resulted from SO2 dry deposition.In addition, the observed dry S deposition was greater in 2002 than in 2000 because of a higher average concentration of SO2 in 2002 than in 2000 and not because of the average dry deposition velocity which was lower for SO2 in 2002. Also,dry SO2 deposition was the dominant fraction of deposited atmospheric sulfur in forests, contributing over 69% of the total annual sulfur deposition. Thus, dry SO2 deposition should be considered when estimating sulfur balance in forest ecological systems.

  17. Enhancing Cold Atmospheric Plasma Treatment Efficiency for Cancer Therapy

    Science.gov (United States)

    Cheng, Xiaoqian

    To improve efficiency and safety of anti-cancer therapies the researchers and clinicians alike are prompted to develop targeted combined therapies that especially minimize damage to healthy tissues while eradicating the body of cancerous tissues. Previous research in cold atmospheric plasma (CAP) and cancer cell interaction has repeatedly proven that cold plasma induced cell death. In this study, we seek to integrate the medical application of CAP. We proposed and implemented 3 novel ideas to enhance efficacy and selectivity of cancer therapy. It is postulated that the reactive oxygen species (ROS) and reactive nitrogen species (RNS) play a major role in the CAP cancer therapy. We determined a mechanism of CAP therapy on glioblastoma cells (U87) through an understanding of the composition of CAP, including output voltage, treatment time, and gas flow-rate. We varied the characteristics of the cold plasma in order to obtain different major species (such as O, OH, N2+, and N2 lines). "plasma dosage" D ~ Q * V * t. is defined, where D is the entire "plasma dosage"; Q is the flow rate of feeding gas; V is output voltage; t is treatment time. The proper CAP dosage caused 3-fold cell death in the U87 cells compared to the normal human astrocytes E6/E7 cells. We demonstrated there is a synergy between AuNPS and CAP in cancer therapy. Specifically, the concentration of AuNPs plays an important role on plasma therapy. At an optimal concentration, gold nanoparticles can significantly induce U87 cell death up to a 30% overall increase compared to the control group with the same plasma dosage but no AuNPs applied. The ROS intensity of the corresponding conditions has a reversed trend compared to cell viability. This matches with the theory that intracellular ROS accumulation results in oxidative stress, which further changes the intracellular pathways, causing damage to the proteins, lipids and DNA. Our results show that this synergy has great potential in improving the

  18. Potential Industrial Applications of the One Atmosphere Uniform Glow Discharge Plasma (OAUGDP) Operating in Ambient Air

    Science.gov (United States)

    Reece Roth, J.

    2004-11-01

    The majority of industrial plasma processing with glow discharges has been conducted at pressures below 10 torr. This tends to limit applications to high value workpieces as a result of the high capital cost of vacuum systems and the production constraints of batch processing. It has long been recognized that glow discharge plasmas would play a much larger industrial role if they could be generated at one atmosphere. The One Atmosphere Uniform Glow Discharge Plasma (OAUGDP), developed at the University of Tennessee's Plasma Sciences Laboratory, is a non-thermal RF plasma operating on displacement currents with the time-resolved characteristics of a classical low pressure DC normal glow discharge. As a glow discharge, the OAUGDP operates with maximum electrical efficiency at the Stoletow point, where the energy input per ion-electron pair is a minimum [1, 2]. Several interdisciplinary teams have investigated potential applications of the OAUGDP. These teams included collaborators from the UTK Textiles and Nonwovens Development Center (TANDEC), and the Departments of Electrical and Computer Engineering, Microbiology, and Food Science and Technology, as well as the NASA Langley Research Center. The potential applications of the OAUGDP have all been at one atmosphere and room temperature, using air as the working gas. These applications include sterilizing medical and dental equipment; sterilizable air filters to deal with the "sick building syndrome"; removal of soot from Diesel engine exhaust; subsonic plasma aerodynamic effects, including flow re-attachment to airfoils and boundary layer modification; electrohydrodynamic (EDH) flow control of working gases; increasing the surface energy of materials; improving the adhesion of paints and electroplated layers: improving the wettability and wickability of fabrics; stripping of photoresist; and plasma deposition and directional etching of potential microelectronic relevance. [1] J. R. Roth, Industrial Plasma Engineering

  19. Deposition of low stress, high transmittance SiC as an x-ray mask membrane using ECR plasma CVD

    CERN Document Server

    Lee, S Y; Lim, S T; Ahn, J H

    1998-01-01

    SiC for x-ray mask membrane is deposited by Electron Cyclotron Resonance plasma Chemical Vapor Deposition from SiH sub 4 /CH sub 4 Ar mixtures. Stoichiometric SiC is deposited at SiH sub 4 /CH sub 4 ratio of 0.4, deposition temperature of 600.deg.C and microwave power of 500 W with +- 5% thickness uniformity, As-deposited film has compressive residual stress, very smooth surface (31 A rms) and high optical transmittance of 90% at 633 nm wavelength. The microstructure of this film consists of the nanocrystalline particle (100 A approx 200A) embedded in amorphous matrix. Residual stress can be turned to tensile stress via Rapid Thermal Annealing in N sub 2 atmosphere, while suppressing structural change during annealing, As a result, smooth (37 A rms) SiC film with moderate tensile stress and high optical transmittance (85% at 633 nm wavelength) is obtained.

  20. Luminescent Nanocrystalline Silicon Carbide Thin Film Deposited by Helicon Wave Plasma Enhanced Chemical Vapour Deposition

    Institute of Scientific and Technical Information of China (English)

    LU Wan-bing; YU Wei; WU Li-ping; CUI Shuang-kui; FU Guang-sheng

    2006-01-01

    Hydrogenated nanocrystalline silicon carbide (SiC) thin films were deposited on the single-crystal silicon substrate using the helicon wave plasma enhanced chemical vapor deposition (HW-PECVD) technique. The influences of magnetic field and hydrogen dilution ratio on the structures of SiC thin film were investigated with the atomic force microscopy (AFM), the Fourier transform infrared absorption (FTIR) and the transmission electron microscopy (TEM). The results indicate that the high plasma activity of the helicon wave mode proves to be a key factor to grow crystalline SiC thin films at a relative low substrate temperature. Also, the decrease in the grain sizes from the level of microcrystalline to that of nanocrystalline can be achieved by increasing the hydrogen dilution ratios. Transmission electron microscopy measurements reveal that the size of most nanocrystals in the film deposited under the higher hydrogen dilution ratios is smaller than the doubled Bohr radius of 3C-SiC (approximately 5.4 nm), and the light emission measurements also show a strong blue photoluminescence at the room temperature, which is considered to be caused by the quantum confinement effect of small-sized SiC nanocrystals.

  1. Plasma-enhanced Deposition of Nano-Structured Carbon Films

    Institute of Scientific and Technical Information of China (English)

    Yang Qiaoqin (杨巧勤); Xiao Chijin (肖持进); A. Hirose

    2005-01-01

    By pre-treating substrate with different methods and patterning the catalyst, selective and patterned growth of diamond and graphitic nano-structured carbon films have been realized through DC Plasma-Enhanced Hot Filament Chemical Vapor Deposition (PE-HFCVD).Through two-step processing in an HFCVD reactor, novel nano-structured composite diamond films containing a nanocrystalline diamond layer on the top of a nanocone diamond layer have been synthesized. Well-aligned carbon nanotubes, diamond and graphitic carbon nanocones with controllable alignment orientations have been synthesized by using PE-HFCVD. The orientation of the nanostructures can be controlled by adjusting the working pressure. In a Microwave Plasma Enhanced Chemical Vapor Deposition (MW-PECVD) reactor, high-quality diamond films have been synthesized at low temperatures (310 ℃~550 ℃) without adding oxygen or halogen gas in a newly developed processing technique. In this process, carbon source originates from graphite etching, instead of hydrocarbon. The lowest growth temperature for the growth of nanocrystalline diamond films with a reasonable growth rate without addition of oxygen or halogen is 260 ℃.

  2. Deposition of Nano-Scaled Coatings Using Inductively Coupled Plasma

    Institute of Scientific and Technical Information of China (English)

    D H Jung; B Park; J J Lee

    2004-01-01

    Nano-scaled Ti-B-N coatings could be produced by inductively coupled plasma (ICP) assisted magnetron spurtering. The properties and microstructure of the coating can be changed drastically by applying ICP to conventional magnetron sputtering. In this work, an internal type rf ICP process is used. The core of this technology is the efficient production and control of self-depositing ions and reactive gas ions by an induced electric field. Ti-B-N coatings were prepared by using a TiB2 target and a gas mixture of N2 and Ar at 200 ℃ and a pressure of 60 mTorr. In addition to ICP, the effect of the substrate bias voltage on the structure and properties of the coating was investigated. By applying ICP and a bias voltage to the substrate the hardness of the Ti-B-N coating is increased by more than 75 GPa, as a result of enhanced ionization in the plasma. The Ti-B-N coating, which has the highest hardness, shows the best surface uniformity and a very dense structure with a grain size of 3 nm. This sample also shows a high crystallinity compared to the coating prepared using other deposition parameters.

  3. Atmospheric pressure plasma accelerates tail regeneration in tadpoles Xenopus laevis

    Science.gov (United States)

    Rivie, A.; Martus, K.; Menon, J.

    2017-08-01

    Atmospheric pressure plasma is a partially ionized gas composed of neutral and charged particles, including electrons and ions, as well as reactive oxygen species (ROS). Recently, it is utilized as possible therapy in oncology, sterilization, skin diseases, wound healing and tissue regeneration. In this study we focused on effect of plasma exposure on tail regeneration of tadpoles, Xenopus leavis with special emphasis on role of ROS, antioxidant defenses and morphological features of the regenerate. When amputated region of the tail was exposed to the helium plasma it resulted in a faster rate of growth, elevated ROS and increase in antioxidant enzymes in the regenerate compared to that of untreated control. An increase in nitric oxide (free radical) as well as activity of nitric oxide synthase(s) were observed once the cells of the regeneration blastema - a mass of proliferating cells are ready for differentiation. Microscopically the cells of the regenerate of plasma treated tadpoles show altered morphology and characteristics of cellular hypoxia and oxidative stress. We summarize that plasma exposure accelerates the dynamics of wound healing and tail regeneration through its effects on cell proliferation and differentiation as well as angiogenesis mediated through ROS signaling.

  4. Dynamics of apokamp-type atmospheric pressure plasma jets

    Science.gov (United States)

    Sosnin, Eduard A.; Panarin, Victor A.; Skakun, Victor S.; Baksht, Evgeny Kh.; Tarasenko, Victor F.

    2017-02-01

    The paper describes a new discharge source of atmospheric pressure plasma jets (APPJs) in air with no gas supply through the discharge region. In this discharge mode, plasma jets develop from the bending point of a bright current channel between two electrodes and are therefore termed an apokamp (from Greek `off' and `bend'). The apokamp can represent single plasma jets of length up 6 cm or several jets, and the temperature of such jets can range from more than 1000 °C at their base to 100-250 °C at their tip. Apokamps are formed at maximum applied voltage of positive polarity, provided that the second electrode is capacitively decoupled with ground. According to high-speed photography with time resolution from several nanoseconds to several tens of nanoseconds, the apokamp consists of a set of plasma bullets moving with a velocity of 100-220 km/s, which excludes the convective mechanism of plasma decay. Estimates on a 100-ns scale show that the near-electrode zones and the zones from which apokamps develop are close in temperature.

  5. On the plasma-based growth of ‘flowing’ graphene sheets at atmospheric pressure conditions

    Science.gov (United States)

    Tsyganov, D.; Bundaleska, N.; Tatarova, E.; Dias, A.; Henriques, J.; Rego, A.; Ferraria, A.; Abrashev, M. V.; Dias, F. M.; Luhrs, C. C.; Phillips, J.

    2016-02-01

    A theoretical and experimental study on atmospheric pressure microwave plasma-based assembly of free standing graphene sheets is presented. The synthesis method is based on introducing a carbon-containing precursor (C2H5OH) through a microwave (2.45 GHz) argon plasma environment, where decomposition of ethanol molecules takes place and carbon atoms and molecules are created and then converted into solid carbon nuclei in the ‘colder’ nucleation zones. A theoretical model previously developed has been further updated and refined to map the particle and thermal fluxes in the plasma reactor. Considering the nucleation process as a delicate interplay between thermodynamic and kinetic factors, the model is based on a set of non-linear differential equations describing plasma thermodynamics and chemical kinetics. The model predictions were validated by experimental results. Optical emission spectroscopy was applied to detect the plasma emission related to carbon species from the ‘hot’ plasma zone. Raman spectroscopy, scanning electron microscopy (SEM), and x-ray photoelectron spectroscopy (XPS) techniques have been applied to analyze the synthesized nanostructures. The microstructural features of the solid carbon nuclei collected from the colder zones of plasma reactor vary according to their location. A part of the solid carbon was deposited on the discharge tube wall. The solid assembled from the main stream, which was gradually withdrawn from the hot plasma region in the outlet plasma stream directed to a filter, was composed by ‘flowing’ graphene sheets. The influence of additional hydrogen, Ar flow rate and microwave power on the concentration of obtained stable species and carbon-dicarbon was evaluated. The ratio of sp3/sp2 carbons in graphene sheets is presented. A correlation between changes in C2 and C number densities and sp3/sp2 ratio was found.

  6. Temperature diagnostics of a non-thermal plasma jet at atmospheric pressure

    Science.gov (United States)

    Schäfer, Jan

    2013-09-01

    The study reflects the concept of the temperature as a physical quantity resulting from the second thermodynamic law. The reliability of different approaches of the temperature diagnostics of open non-equilibrium systems is discussed using examples of low temperature atmospheric pressure discharges. The focus of this work is a miniaturized non-thermal atmospheric pressure plasma jet for local surface treatment at ambient atmosphere. The micro-discharge is driven with a capacitively coupled radio frequency electric field at 27.12 MHz and fed with argon at rates of about 1 slm through the capillary with an inner diameter of 4 mm. The discharge consists of several contracted filaments with diameter around 300 μm which are rotating azimuthally in the capillary in a self-organized manner. While the measured temperatures of the filament core exceed 700 K, the heat impact on a target below the plasma jet remains limited leading to target temperatures below 400 K. Different kinds of temperatures and energy transport processes are proposed and experimentally investigated. Nevertheless, a reliable and detailed temperature diagnostics is a challenge. We report on a novel diagnostics approach for the spatially and temporally resolved measurement of the gas temperature based on the optical properties of the plasma. Laser Schlieren Deflectometry is adapted to explore temperature profiles of filaments and their behaviour. In parallel, the method demonstrates a fundamental Fermat's principle of minimal energy. Information acquired with this method plays an important role for the optimization of local thin film deposition and surface functionalization by means of the atmospheric pressure plasma jet. The work was supported in part by the Deutsche Forschungsgemeinschaft within SFB-TR 24.

  7. Sterilization of Surfaces with a Handheld Atmospheric Pressure Plasma

    Science.gov (United States)

    Hicks, Robert; Habib, Sara; Chan, Wai; Gonzalez, Eleazar; Tijerina, A.; Sloan, Mark

    2009-10-01

    Low temperature, atmospheric pressure plasmas have shown great promise for decontaminating the surfaces of materials and equipment. In this study, an atmospheric pressure, oxygen and argon plasma was investigated for the destruction of viruses, bacteria, and spores. The plasma was operated at an argon flow rate of 30 L/min, an oxygen flow rate of 20 mL/min, a power density of 101.0 W/cm^3 (beam area = 5.1 cm^2), and at a distance from the surface of 7.1 mm. An average 6log10 reduction of viable spores was obtained after only 45 seconds of exposure to the reactive gas. By contrast, it takes more than 35 minutes at 121^oC to sterilize anthrax in an autoclave. The plasma properties were investigated by numerical modeling and chemical titration with nitric oxide. The numerical model included a detailed reaction mechanism for the discharge as well as for the afterglow. It was predicted that at a delivered power density of 29.3 W/cm^3, 30 L/min argon, and 0.01 volume% O2, the plasma generated 1.9 x 10^14 cm-3 O atoms, 1.6 x 10^12 cm-3 ozone, 9.3 x 10^13 cm-3 O2(^1δg), and 2.9 x 10^12 cm-3 O2(^1σ^+g) at 1 cm downstream of the source. The O atom density measured by chemical titration with NO was 6.0 x 10^14 cm-3 at the same conditions. It is believe that the oxygen atoms and the O2(^1δg) metastables were responsible for killing the anthrax and other microorganisms.

  8. A global mechanism creating low atmospheric luminous cold plasmas

    Science.gov (United States)

    Gitle Hauge, Bjørn; Petter Strand, Erling

    2014-05-01

    Red, white/yellow and blue balls of light have been observed in the low atmosphere over the Hessdalen valley , Norway, standing still and moving horizontally with random speed. Characteristics of these transient luminous phenomena in Hessdalen, and data from America, suggest that the process which creates these low atmospheric plasmas is a global mechanism, not only localized to the remote and desolated Hessdalen valley in Norway (62Deg.N - 11Deg.E). Transient luminous phenomena's has been observed in the low atmosphere over the Hessdalen valley for over 200 years. The first written documentation goes back to 1811 when the priest Jakob Tode Krogh wrote about it in his diary. Since 1982, inhabitants, tourists, journalists and scientists have done recurrent observations. E.P.Strand conducted the first scientific campaign in 1984, documenting over 50 observations in one month. 15 years later, Norwegian and Italian scientists installed the first permanent automated research base here. In 2010 French researchers joined this collaboration and installed two additional research bases. This transient luminous phenomenon, TLP, has been detected simultaneously on optical and radar devices, but electromagnetic radiation from this phenomenon has until now eluded detection. Smirnov (1994) and Zou(1994) was among the first scientist who used plasma physics trying to explain this phenomenon. Work done by Pavia & Taft (2010 and 2012) suggests that the TLP in Hessdalen probably is dusty or cold plasma, arranged as a cluster of Coulomb crystals. Optical spectrum data obtained by Strand (1984), Teodorani (2004) and Hauge (2007) showing a continuous optical spectrum support this hypothesis. Pictures of spiraling light rays obtained by Strand in 1984, and Hauge in 2004 and 2010 suggests that this plasma is moving in a strong magnetic field, and might be created by it. Radar reflections from the TLP in Hessdalen obtained by Strand in 1984 and Montebugnoli and Monari in 2007 points

  9. Study of atmospheric pressure weakly ionized plasma as surface compatibilization technique for improved plastic composites loaded with cellulose based fillers

    Science.gov (United States)

    Lekobou, William Pimakouon

    Atmospheric pressure plasmas have gained considerable interest from researchers recently for their unique prospective of engineering surfaces with plasma without the need of vacuum systems. They offer the advantage of low energy consumption, minimal capital cost and their simplicity as compared to conventional low pressure plasmas make them easy to upscale from laboratory to industry size. The present dissertation summarizes results of our attempt at applying atmospheric pressure weakly ionized plasma (APWIP) to the engineering of plastic composites filled with cellulose based substrates. An APWIP reactor was designed and built based on a multipoint-to-grounded ring and screen configurations. The carrier gas was argon and acetylene serves as the precursor molecule. The APWIP reactors showed capability of depositing plasma polymerized coating rich in carbon on substrates positioned within the electrode gap as well as downstream of the plasma discharge into the afterglow region. Our findings show that films grow by forming islands which for prolonged deposition time grow into thin films showing nodules, aggregates of nodules and microspheres. They also show chemical structure similar to films deposited from hydrocarbons with other conventional plasma techniques. The plasma polymerized deposits were used on substrates to modify their surface properties. Results show the surface of wood veneer and wood flour can be finely tuned from hydrophilic to hydrophobic. It was achieved by altering the topography of the surfaces along with their chemical composition. The wettability of wood veneer was investigated with contact angle measurements on capacitive drops and the capillary effect was utilized to assess surface properties of wood flour exposed to the discharges.

  10. IR emission from the target during plasma magnetron sputter deposition

    Energy Technology Data Exchange (ETDEWEB)

    Cormier, P.-A. [GREMI, Université d' Orléans, 14 rue d' Issoudun, B.P. 6744, 45067 Orleans Cedex2 (France); Thomann, A.-L., E-mail: anne-lise.thomann@univ-orleans.fr [GREMI, Université d' Orléans, 14 rue d' Issoudun, B.P. 6744, 45067 Orleans Cedex2 (France); Dolique, V. [LMA, Université Claude Bernard Lyon I 7 Avenue Pierre de Coubertin, 69622 Villeurbanne Cedex (France); Balhamri, A. [ChIPS, Université de Mons, 20 Place du Parc, 7000 Mons (Belgium); Université Hassan 1, École Supérieure de Technologie, 218 Berrechid (Morocco); Dussart, R.; Semmar, N.; Lecas, T.; Brault, P. [GREMI, Université d' Orléans, 14 rue d' Issoudun, B.P. 6744, 45067 Orleans Cedex2 (France); Snyders, R. [ChIPS, Université de Mons, 20 Place du Parc, 7000 Mons (Belgium); Materia Nova R and D Center, Avenue Corpernic 1, Mons (Belgium); Konstantinidis, S. [Materia Nova R and D Center, Avenue Corpernic 1, Mons (Belgium)

    2013-10-31

    In this article, energy flux measurements at the substrate location are reported. In particular, the energy flux related to IR radiation emanating from the titanium (10 cm in diam.) target surface is quantified during magnetron sputter deposition processes. In order to modulate the plasma–target surface interaction and the radiative energy flux thereof, the working conditions were varied systematically. The experiments were performed in balanced and unbalanced magnetic field configurations with direct current (DC), pulsed DC and high power impulse magnetron sputtering (HiPIMS) discharges. The power delivered to the plasma was varied too, typically from 100 to 800 W. Our data show that the IR contribution to the total energy flux at the substrate increases with the supplied sputter power and as the discharge is driven in a pulse regime. In the case of HiPIMS discharge generated with a balanced magnetic field, the energy flux associated to the IR radiation produced by the target becomes comparable to the energy flux originating from collisional processes (interaction of plasma particles such as ions, electron, sputtered atoms etc. with the substrate). From IR contribution, it was possible to estimate the rise of the target surface temperature during the sputtering process. Typical values found for a titanium target are in the range 210 °C to 870 °C. - Highlights: • During magnetron sputtering process the heated target emits IR radiation. • We follow in real time the energy transferred to the deposited film by IR radiation. • IR radiation can be the main energy contribution in balanced pulsed processes. • IR radiation might affect the deposition process and the final film properties.

  11. Plasma spray deposition of graded metal-ceramic coatings

    Energy Technology Data Exchange (ETDEWEB)

    Musil, J. (Inst. of Tech. and Reliability of Structures, Czechoslovak Academy of Sciences, Plzen (Czechoslovakia)); Fiala, J. (Central Research Inst., Plzen (Czechoslovakia))

    1992-05-20

    Plasma spraying of graded coatings is described and the metal-ceramic interface of the graded intermediate zone is analysed in terms of a simple physical model. Special attention is devoted to the dominant deposition parameters, powder characteristics and the injector configuration for powder feeding, which play a fundamental role in graded coating deposition with controlled formation of a metal-ceramic intermediate zone. On the basis of a knowledge of these parameters, a new and original formula for the coefficient of homogeneity for simultaneous deposition of metal and ceramic particles at the same spot on the substrate is derived. Furthermore, very interesting topotactical relations are described for the metal-ceramic interface of the graded zone. Various techniques of structural analysis (X-ray diffraction, scanning electron microscopy, optical microscopy) and simple thermodynamic calculations allow a new interpretation to be given of the bonding between the metal and ceramic components. The cohesion of graded metal-ceramic coatings is predicted to be higher than that of ceramic coatings with a metallic bond layer. The results are illustrated by a NiCr-ZrO{sub 2}(MgO) graded coating. (orig.).

  12. Atmospherically deposited trace metals from bulk mineral concentrate port operations

    Energy Technology Data Exchange (ETDEWEB)

    Taylor, Mark Patrick, E-mail: mark.taylor@mq.edu.au

    2015-05-15

    Although metal exposures in the environment have declined over the last two decades, certain activities and locations still present a risk of harm to human health. This study examines environmental dust metal and metalloid hazards (arsenic, cadmium, lead and nickel) associated with bulk mineral transport, loading and unloading port operations in public locations and children's playgrounds in the inner city of Townsville, northern Queensland. The mean increase in lead on post-play hand wipes (965 μg/m{sup 2}/day) across all sites was more than 10-times the mean pre-play loadings (95 μg/m{sup 2}/day). Maximum loading values after a 10-minute play period were 3012 μg/m{sup 2}, more than seven times the goal of 400 μg/m{sup 2} used by the Government of Western Australia (2011). Maximum daily nickel post-play hand loadings (404 μg/m{sup 2}) were more than 26 times above the German Federal Immission Control Act 2002 annual benchmark of 15 μg/m{sup 2}/day. Repeat sampling over the 5-day study period showed that hands and surfaces were re-contaminated daily from the deposition of metal-rich atmospheric dusts. Lead isotopic composition analysis of dust wipes ({sup 208}Pb/{sup 207}Pb and {sup 206}Pb/{sup 207}Pb) showed that surface dust lead was similar to Mount Isa type ores, which are exported through the Port of Townsville. While dust metal contaminant loadings are lower than other mining and smelting towns in Australia, they exceeded national and international benchmarks for environmental quality. The lessons from this study are clear — even where operations are considered acceptable by managing authorities, targeted assessment and monitoring can be used to evaluate whether current management practices are truly best practice. Reassessment can identify opportunities for improvement and maximum environmental and human health protection. - Graphical abstract: Post-play hand wipe, Headland Park, Townsville, Australia. - Highlights: • Bulk mineral port

  13. Development of atmospheric pressure plasma needle jet for sterilization applications

    Science.gov (United States)

    Elfa, Rizan Rizon; Ahmad, Mohd Khairul; Soon, Chin Fhong; Sahdan, Mohd Zainizan; Lias, Jais; Wibowo, Kusnanto Mukti; Bakar, Ahmad Shuhaimi Abu; Arshad, Mohd Khairuddin Md; Hashim, Uda; Nayan, Nafarizal

    2017-09-01

    Inactivation of bacteria or sterilization has been a major issue in the medical field, especially regarding of human safety, whereby, in a huge scenario fatality can be caused by hazardous bacteria. Often, E-coli as gram-negative bacteria are selected as a key indicator of proper sterilization process as E-coli is tough and dormant bacteria. The technology in sterilization has moved on from chemical, wet and irradiation sterilization to a high promising device such as atmospheric pressure plasma needle jet (APPNJ). It has been reported that atmospheric pressure plasma has provided bundle of advantages over earlier sterilization process. The APPNJ is developed in our lab using high frequency and high voltage neon transformer power supply connected to copper needle and copper sheet electrodes. The gas discharge is Ar gas flowing at 40 L/min through a quartz glass tube. The E-coli bacteria are self-cultured from waste water and then treated with APPNJ. The treatment processes are run into two difference gaps between the plasma orifice and sample with various treatment times. Only 40s is required by direct treatment to achieve 100% killing of E-coli. On the other hand, indirect treatment has inactivated 50% of the E-coli in 40s. In this study, direct and indirect effect of APPNJ to the E-coli can be observed which can be utilized into sterilization of bio-compatible material applications.

  14. Nonthermal atmospheric argon plasma jet effects on Escherichia coli biomacromolecules.

    Science.gov (United States)

    Hosseinzadeh Colagar, Abasalt; Memariani, Hamed; Sohbatzadeh, Farshad; Valinataj Omran, Azadeh

    2013-12-01

    Nonthermal atmospheric plasma jet, a promising technology based on ionized gas at low temperatures, can be applied for disinfection of contaminated surfaces. In this study, Escherichia coli cells and their macromolecules were exposed to the nonthermal atmospheric argon plasma jet for different time durations. Total protein, genomic DNA, and malondialdehyde (MDA) levels of E. coli were assessed by sodium dodecyl sulfate-polyacrylamide gel electrophoresis and silver staining; agarose gel electrophoresis; and measurement of absorbance at 534 nm, respectively. After exposure, the spectroscopic results of liquid samples indicated that the survival reduction of E. coli can reach to 100 % in an exposure time of 600 s. Moreover, inactivation zones of E. coli, DNA degradation, and MDA levels were significantly increased. Additionally, banding patterns of total protein were changed and amino acid concentrations increased following ninhydrin test. The experimental results suggest that the nonthermal plasma could serve as an effective instrument for both sterilizing E. coli and degrading macromolecules from the surface of the objects being sterilized.

  15. Characterization of Thin Films Deposited with Precursor Ferrocene by Plasma Enhanced Chemical Vapour Deposition

    Institute of Scientific and Technical Information of China (English)

    YAO Kailun; ZHENG Jianwan; LIU Zuli; JIA Lihui

    2007-01-01

    In this paper,the characterization of thin films,deposited with the precursor ferrocene(FcH)by the plasma enhanced chemical vapour deposition(PECVD)technique,was investigated.The films were measured by Scanning Electronic Microscopy(SEM),Atomic Force Microscopy(AFM),Electron Spectroscopy for Chemical Analysis(ESCA),and superconducting Quantum Interference Device(SQUID).It was observed that the film's layer is homogeneous in thickness and has a dense morphology without cracks.The surface roughness is about 36 nm.From the results of ESCA,it can be inferred that the film mainly contains the compound FeOOH,and carbon is combined with oxygen in different forms under different supply-powers.The hysteresis loops indicate that the film is of soft magnetism.

  16. Application of atmospheric solution precursor plasma spray to photocatalytic devices for small and medium industries in developing countries

    Science.gov (United States)

    Kindole, Dickson; Ando, Yasutaka

    2017-01-01

    For development of a functional film deposition process with high deposition rate, as a basic study, TiO2 films were deposited by atmospheric solution precursor plasma spray (ASPPS) process. Ethanol-diluted titanium tetraisobutoxide [TTIB: Ti(OC4H9)4] was used as a feedstock. To achieve a high plasma thermal energy at a low discharge power, N2-dominant Ar/N2 as the plasma working gas was used, for film deposition at various deposition distances. Consequently, photocatalytic TiO2 with a rutile/anatase mixture film structure was deposited evenly in this case. By conducting methylene blue decomposition and wettability tests, photocatalytic properties of the film were confirmed. When a TiO2 film was applied to photocatalytic dye-sensitized solar cells (DSSCs), the cells generated an electromotive force of 0.143V oc, which is close to those of commercial DSSCs. From these results, the ASPPS process was found to have high potential for high rate functional film deposition and was cost effective, making it suitable for developing countries.

  17. On non-equilibrium atmospheric pressure plasma jets and plasma bullet

    Science.gov (United States)

    Lu, Xinpei

    2012-10-01

    Because of the enhanced plasma chemistry, atmospheric pressure nonequilibrium plasmas (APNPs) have been widely studied for several emerging applications such as biomedical applications. For the biomedical applications, plasma jet devices, which generate plasma in open space (surrounding air) rather than in confined discharge gaps only, have lots of advantages over the traditional dielectric barrier discharge (DBD) devices. For example, it can be used for root canal disinfection, which can't be realized by the traditional plasma device. On the other hand, currently, the working gases of most of the plasma jet devices are noble gases or the mixtures of the noble gases with small amount of O2, or air. If ambient air is used as the working gas, several serious difficulties are encountered in the plasma generation process. Amongst these are high gas temperatures and disrupting instabilities. In this presentation, firstly, a brief review of the different cold plasma jets developed to date is presented. Secondly, several different plasma jet devices developed in our lab are reported. The effects of various parameters on the plasma jets are discussed. Finally, one of the most interesting phenomena of APNP-Js, the plasma bullet is discussed and its behavior is described. References: [1] X. Lu, M. Laroussi, V. Puech, Plasma Sources Sci. Technol. 21, 034005 (2012); [2] Y. Xian, X. Lu, S. Wu, P. Chu, and Y. Pan, Appl. Phys. Lett. 100, 123702 (2012); [3] X. Pei, X. Lu, J. Liu, D. Liu, Y. Yang, K. Ostrikov, P. Chu, and Y. Pan, J. Phys. D 45, 165205 (2012).

  18. Photocatalytic Anatase TiO2 Thin Films on Polymer Optical Fiber Using Atmospheric-Pressure Plasma.

    Science.gov (United States)

    Baba, Kamal; Bulou, Simon; Choquet, Patrick; Boscher, Nicolas D

    2017-04-06

    Due to the undeniable industrial advantages of low-temperature atmospheric-pressure plasma processes, such as low cost, low temperature, easy implementation, and in-line process capabilities, they have become the most promising next-generation candidate system for replacing thermal chemical vapor deposition or wet chemical processes for the deposition of functional coatings. In the work detailed in this article, photocatalytic anatase TiO2 thin films were deposited at a low temperature on polymer optical fibers using an atmospheric-pressure plasma process. This method overcomes the challenge of forming crystalline transition metal oxide coatings on polymer substrates by using a dry and up-scalable method. The careful selection of the plasma source and the titanium precursor, i.e., titanium ethoxide with a short alkoxy group, allowed the deposition of well-adherent, dense, and crystalline TiO2 coatings at low substrate temperature. Raman and XRD investigations showed that the addition of oxygen to the precursor's carrier gas resulted in a further increase of the film's crystallinity. Furthermore, the films deposited in the presence of oxygen exhibited a better photocatalytic activity toward methylene blue degradation assumedly due to their higher amount of photoactive {101} facets.

  19. Contribution of Asian dust to atmospheric deposition of radioactive cesium ((137)Cs).

    Science.gov (United States)

    Fukuyama, Taijiro; Fujiwara, Hideshi

    2008-11-01

    Both Asian dust (kosa) transported from the East Asian continent and locally suspended dust near monitoring sites contribute to the observed atmospheric deposition of (137)Cs in Japan. To estimate the relative contribution of these dust phenomena to the total (137)Cs deposition, we monitored weekly deposition of mineral particles and (137)Cs in spring. Deposition of (137)Cs from a single Asian dust event was 62.3 mBq m(-2) and accounted for 67% of the total (137)Cs deposition during the entire monitoring period. Furthermore, we found high (137)Cs specific activity in the Asian dust deposition sample. Although local dust events contributed to (137)Cs deposition, their contribution was considerably smaller than that of Asian dust. We conclude that the primary source of atmospheric (137)Cs in Japan is dust transported from the East Asian continent.

  20. LDPE Surface Modifications Induced by Atmospheric Plasma Torches with Linear and Showerhead Configurations

    CERN Document Server

    Rich, Sami Abou; Leroy, Perrine; Reniers, François; Nittler, Laurent; Pireaux, Jean-Jacques

    2016-01-01

    Low density polyethylene (LDPE) surfaces have been plasma modified to improve their nanostructural and wettability properties. These modifications can significantly improve the deposition of subsequent layers such as films with specific barrier properties. For this purpose, we compare the treatments induced by two atmospheric plasma torches with different configurations (showerhead vs. linear). The modifications of LDPE films in terms of chemical surface composition and surface morphology are evidenced by X-ray photoelectron spectro-scopy, water contact angles measurements, and atomic force microscopy. A comparison between the two post-discharge treatments is achieved for several torch-to-substrate distances (gaps), treatment times, and oxygen flow rates in terms of etching rate, roughening rate, diffusion of oxygen into the subsur-face and hydrophilicity. By correlating these results with the chemical composition of the post-discharges, we identify and compare the 'species which are responsible for the chemi...

  1. Novel Diamond Films Synthesis Strategy: Methanol and Argon Atmosphere by Microwave Plasma CVD Method Without Hydrogen

    Science.gov (United States)

    Yang, Li; Jiang, Caiyi; Guo, Shenghui; Zhang, Libo; Gao, Jiyun; Peng, Jinhui; Hu, Tu; Wang, Liang

    2016-09-01

    Diamond thin films are grown on silicon substrates by only using methanol and argon mixtures in microwave plasma chemical vapor deposition (MPCVD) reactor. It is worth mentioning that the novel strategy makes the synthesis reaction works smoothly without hydrogen atmosphere, and the substrates temperature is only 500 °C. The evidence of surface morphology and thickness under different time is obtained by characterizing the samples using scanning electron microscopy (SEM). X-ray diffractometer (XRD) spectrum reveals that the preferential orientation of (111) plane sample is obtained. The Raman spectra indicate that the dominant component of all the samples is a diamond. Moreover, the diamond phase content of the targeted films was quantitatively analyzed by X-ray photoelectron spectroscopy (XPS) method, and the surface roughness of diamond films was investigated by atomic force microscope (AFM). Meanwhile, the possible synthesis mechanism of the diamond films in methanol- and argon-mixed atmosphere was discussed.

  2. Positioning of the Precursor Gas Inlet in an Atmospheric Dielectric Barrier Reactor, and its Effect on the Quality of Deposited TiOx Thin Film Surface

    Directory of Open Access Journals (Sweden)

    Jan Píchal

    2013-01-01

    Full Text Available Thin film technology has become pervasive in many applications in recent years, but it remains difficult to select the best deposition technique. A further consideration is that, due to ecological demands, we are forced to search for environmentally benign methods. One such method might be the application of cold plasmas, and there has already been a rapid growth in studies of cold plasma techniques. Plasma technologies operating at atmospheric pressure have been attracting increasing attention. The easiest way to obtain low temperature plasma at atmospheric pressure seems to be through atmospheric dielectric barrier discharge (ADBD. We used the plasma enhanced chemical vapour deposition (PECVD method applying atmospheric dielectric barrier discharge (ADBD plasmafor TiOx thin films deposition, employing titanium isopropoxide (TTIP and oxygen as reactants, and argon as a working gas. ADBD was operated in filamentary mode. The films were deposited on glass. We studied the quality of the deposited TiOx thin film surface for various precursor gas inlet positions in the ADBD reactor. The best thin films quality was achieved when the precursor gases were brought close to the substrate surface directly through the inlet placed in one of the electrodes.High hydrophilicity of the samples was proved by contact angle tests (CA. The film morphology was tested by atomic force microscopy (AFM. The thickness of the thin films varied in the range of (80 ÷ 210 nm in dependence on the composition of the reactor atmosphere. XPS analyses indicate that composition of the films is more like the composition of TiOxCy.

  3. Microwave capillary plasmas in helium at atmospheric pressure

    Science.gov (United States)

    Santos, M.; Noël, C.; Belmonte, T.; Alves, L. L.

    2014-07-01

    This work uses both simulations and experiments to study helium plasmas (99.999% purity), sustained by surface-wave discharges (2.45 GHz frequency) in capillary tubes (3 mm in-radius) at atmospheric pressure. The simulations use a self-consistent homogeneous and stationary collisional-radiative model (CRM) that solves the rate balance equations for the different species present in the plasma (electrons, He+ and He_2^+ ions, He(n ⩽ 6) excited states and He_2^* excimers) and the gas thermal balance equation, coupled with the two-term electron Boltzmann equation (including direct and stepwise inelastic and superelastic collisions as well as electron-electron collisions). The experiments use optical emission spectroscopy diagnostics to measure the electron density ne (from the Hβ Stark broadening), the gas temperature Tg (from the ro-vibrational transitions of OH, present at trace concentrations) and the populations of excited states in the energy region 22.7-24.2 eV, whose spectrum allows determining the excitation temperature Texc. Measurements yield ne ≃ (2.45 ± 1.4) × 1013 cm-3, Tg ≃ 1700 ± 100 K and Texc ≃ 2793 ± 116 K, for a ˜180 ± 10 W power coupled and ˜1 cm length plasma column. The model predictions at ne = 1.7 × 1013 cm-3 are in very good agreement with measurements yielding Tg = 1800 K, Texc = 2792 K (for ˜30% average relative error between calculated and measured excited-state densities), and a power absorbed by the plasma per unit length of 165 W cm-1. The model results depend strongly on ne, and hence on the plasma conductivity and on the power coupled to the plasma. The coupling of a thermal module to the CRM has been shown to be crucial. Increasing the electron density leads to very high gas temperature values, which limits the variation range of (ne, Tg) as input parameters to the model.

  4. Plasma Flow Past Cometary and Planetary Satellite Atmospheres

    Science.gov (United States)

    Combi, Michael R.; Gombosi, Tamas I.; Kabin, Konstantin

    2000-01-01

    The tenuous atmospheres and ionospheres of comets and outer planet satellites share many common properties and features. Such similarities include a strong interaction with their outer radiation, fields and particles environs. For comets the interaction is with the magnetized solar wind plasma, whereas for satellites the interaction is with the strongly magnetized and corotating planetary magnetospheric plasma. For this reason there are many common or analogous physical regimes, and many of the same modeling techniques are used to interpret remote sensing and in situ measurements in order to study the important underlying physical phenomena responsible for their appearances. We present here a review of various modeling approaches which are used to elucidate the basic properties and processes shaping the energetics and dynamics of these systems which are similar in many respects.

  5. Use of cold atmospheric plasma in the treatment of cancer.

    Science.gov (United States)

    Babington, Parker; Rajjoub, Kenan; Canady, Jerome; Siu, Alan; Keidar, Michael; Sherman, Jonathan H

    2015-01-01

    Cold atmospheric plasma (CAP) is an emerging modality for the treatment of solid tumors. In-vitro experiments have demonstrated that with increasing doses of plasma, tumor cells assays display decreased cell viability. CAP is theorized to induce tumor cells into apoptosis via multiple pathways including reactive oxygen and nitrogen species as well as cell cycle disruption. Studies have shown CAP treatment can decrease mouse model glioblastoma multiforme tumor volume by 56%, increase life span by 60%, and maintain up to 85% viability of normal cells. Emerging evidence suggests that CAP is a viable in-vivo treatment for a number of tumors, including glioblastoma, as it appears to selectively induce tumor cell death while noncancerous cells remain viable.

  6. The solvation of electrons by an atmospheric-pressure plasma

    Science.gov (United States)

    Rumbach, Paul; Bartels, David M.; Sankaran, R. Mohan; Go, David B.

    2015-06-01

    Solvated electrons are typically generated by radiolysis or photoionization of solutes. While plasmas containing free electrons have been brought into contact with liquids in studies dating back centuries, there has been little evidence that electrons are solvated by this approach. Here we report direct measurements of solvated electrons generated by an atmospheric-pressure plasma in contact with the surface of an aqueous solution. The electrons are measured by their optical absorbance using a total internal reflection geometry. The measured absorption spectrum is unexpectedly blue shifted, which is potentially due to the intense electric field in the interfacial Debye layer. We estimate an average penetration depth of 2.5+/-1.0 nm, indicating that the electrons fully solvate before reacting through second-order recombination. Reactions with various electron scavengers including H+, NO2-, NO3- and H2O2 show that the kinetics are similar, but not identical, to those for solvated electrons formed in bulk water by radiolysis.

  7. Atmospheric wet and dry deposition of trace elements at 10 sites in Northern China

    Science.gov (United States)

    Pan, Y. P.; Wang, Y. S.

    2015-01-01

    Atmospheric deposition is considered to be a major process that removes pollutants from the atmosphere and an important source of nutrients and contaminants for ecosystems. Trace elements (TEs), especially toxic metals deposited on plants and into soil or water, can cause substantial damage to the environment and human health due to their transfer and accumulation in food chains. Despite public concerns, quantitative knowledge of metal deposition from the atmosphere to ecosystems remains scarce. To advance our understanding of the spatiotemporal variations in the magnitudes, pathways, compositions and impacts of atmospherically deposited TEs, precipitation (rain and snow) and dry-deposited particles were collected simultaneously at 10 sites in Northern China from December 2007 to November 2010. The measurements showed that the wet and dry depositions of TEs in the target areas were orders of magnitude higher than previous observations within and outside China, generating great concern over the potential risks. The spatial distribution of the total (wet plus dry) deposition flux was consistent with that of the dry deposition, with a significant decrease from industrial and urban areas to suburban, agricultural and rural sites, while the wet deposition exhibited less spatial variation. In addition, the seasonal variation of wet deposition was also different from that of dry deposition, although they were both governed by the precipitation and emission patterns. For the majority of TEs that exist as coarse particles, dry deposition dominated the total flux at each site. This was not the case for potassium, nickel, arsenic, lead, zinc, cadmium, selenium, silver and thallium, for which the relative importance between wet and dry deposition fluxes varied by site. Whether wet deposition is the major atmospheric cleansing mechanism for the TEs depends on the size distribution of the particles. We found that atmospheric inputs of copper, lead, zinc, cadmium, arsenic and

  8. Long-Term Simulated Atmospheric Nitrogen Deposition Alters Leaf and Fine Root Decomposition

    Science.gov (United States)

    Atmospheric nitrogen deposition has been suggested to increase forest carbon sequestration across much of the Northern Hemisphere; slower organic matter decomposition could contribute to this increase. At four sugar maple (Acer saccharum)-dominated northern hardwood forests, we p...

  9. Wet and dry deposition of atmospheric nitrogen at ten sites in Northern China

    Directory of Open Access Journals (Sweden)

    Y. P. Pan

    2012-01-01

    Full Text Available Emissions of reactive nitrogen (N species can affect surrounding ecosystems via atmospheric deposition. However, few long-term and multi-site measurements have focused on both the wet and the dry deposition of individual N species in large areas of Northern China. Thus, the magnitude of atmospheric deposition of various N species in Northern China remains uncertain. In this study, the wet and dry atmospheric deposition of different N species was investigated during a three-year observation campaign at ten selected sites in Northern China. The results indicate that N deposition levels in Northern China were high with a ten-site, three-year average of 60.6 kg N ha−1 yr−1. The deposition levels showed spatial and temporal variation in the range of 28.5–100.4 kg N ha−1 yr−1. Of the annual total deposition, 40% was deposited via precipitation, and the remaining 60% was comprised of dry-deposited forms. Compared with gaseous N species, particulate N species were not the major contributor of dry-deposited N; they contributed approximately 10% to the total flux. On an annual basis, oxidized species accounted for 21% of total N deposition, thereby implying that other forms of gaseous N, such as NH3, comprised a dominant portion of the total flux. The contribution of NO3 to N deposition was enhanced in certain urban and industrial areas. As expected, the total N deposition in Northern China was significantly larger than the values reported by national scale monitoring networks in Europe, North America and East Asia because of high rates of wet deposition and gaseous NH3 dry deposition. The results have three important implications. First, atmospheric N deposition in Northern China falls within the range of critical loads for temperate forests and grasslands, a threshold above which harmful ecological effects to specified parts of temperate ecosystems often

  10. Plasma environment during hot cathode direct current discharge plasma chemical vapor deposition of diamond films

    Institute of Scientific and Technical Information of China (English)

    朱晓东; 詹如娟; 周海洋; 胡敏; 温晓辉; 周贵恩; 李凡庆

    1999-01-01

    The plasma characteristics have been investigated in situ by using optical emission spectroscopy (OES) and the Langmuir probe during hot cathode direct current discharge plasma chemical vapor deposition of diamond films. The changes of atomic H and CH radical in the ground state have been calculated quantitatively according to the results of OES and the Langmuir probe measurement as discharge current density varied. It is shown that atomic H and CH radicals both in the ground state and in the excited state increase with the enhancement of the discharge current density in the plasma. The electron density and CH emission intensity increase linearly with the enhancement of discharge current densities. The generation of different carbon-containing radicals is related to the elevation of electron temperature. Combining the growth process of diamond films and the diagnostic results, it is shown that atomic H in the excited state may improve the diamond growth efficiently, and the increase of electron temperat

  11. Correlation between helium atmospheric pressure plasma jet (APPJ) variables and plasma induced DNA damage

    Science.gov (United States)

    Adhikari, Ek R.; Ptasinska, Sylwia

    2016-09-01

    A helium atmospheric pressure plasma jet (APPJ) source with a dielectric capillary and two tubular electrodes was used to induce damage in aqueous plasmid DNA. The fraction of different types of DNA damage (i.e., intact or undamaged, double strand breaks (DSBs), and single strand breaks (SSBs)) that occurred as the result of plasma irradiation was quantified through analysis of agarose gel electrophoresis images. The total DNA damage increased with an increase in both flow rate and duration of irradiation, but decreased with an increase in distance between the APPJ and sample. The average power of the plasma was calculated and the length of APPJ was measured for various flow rates and voltages applied. The possible effects of plasma power and reactive species on DNA damage are discussed.

  12. Nanostructured europium oxide thin films deposited by pulsed laser ablation of a metallic target in a He buffer atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Luna, H.; Franceschini, D. F.; Prioli, R.; Guimaraes, R. B.; Sanchez, C. M.; Canal, G. P.; Barbosa, M. D. L.; Galvao, R. M. O. [Instituto de Fisica, Universidade Federal do Rio de Janeiro, Cx. Postal 68528, Rio de Janeiro, RJ 21941-972 (Brazil); Instituto de Fisica, Universidade Federal Fluminense, Niteroi, RJ 24210-346 (Brazil); Departamento de Fisica, Pontificia Universidade Catolica do Rio de Janeiro, Rua Marques de Sao Vicente 225, 22453-970, Rio de Janeiro, RJ (Brazil); Instituto de Fisica, Universidade Federal Fluminense, Niteroi, RJ 24210-346 (Brazil); Centro Brasileiro de Pesquisas Fisicas, Laboratorio de Plasmas Aplicados, Rua Xavier Sigaud 150, 22290-180, Rio de Janeiro, RJ (Brazil); Instituto de Fisica, Departamento de Fisica Nuclear, Universidade de Sao Paulo, Caixa Postal 66328, 05315-970, Sao Paulo, SP (Brazil); Centro Brasileiro de Pesquisas Fisicas, Laboratorio de Plasmas Aplicados, Rua Xavier Sigaud 150, 22290-180, Rio de Janeiro, RJ (Brazil)

    2010-09-15

    Nanostrucured europium oxide and hydroxide films were obtained by pulsed Nd:YAG (532 nm) laser ablation of a europium metallic target, in the presence of a 1 mbar helium buffer atmosphere. Both the produced film and the ambient plasma were characterized. The plasma was monitored by an electrostatic probe, for plume expansion in vacuum or in the presence of the buffer atmosphere. The time evolution of the ion saturation current was obtained for several probe to substrate distances. The results show the splitting of the plume into two velocity groups, being the lower velocity profile associated with metal cluster formation within the plume. The films were obtained in the presence of helium atmosphere, for several target-to-substrate distances. They were analyzed by Rutherford backscattering spectrometry, x-ray diffraction, and atomic force microscopy, for as-deposited and 600 deg. C treated-in-air samples. The results show that the as-deposited samples are amorphous and have chemical composition compatible with europium hydroxide. The thermally treated samples show x-ray diffraction peaks of Eu{sub 2}O{sub 3}, with chemical composition showing excess oxygen. Film nanostructuring was shown to be strongly correlated with cluster formation, as shown by velocity splitting in probe current versus time plots.

  13. Plasma interactions determine the composition in pulsed laser deposited thin films

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Jikun; Stender, Dieter; Conder, Kazimierz; Wokaun, Alexander; Schneider, Christof W.; Lippert, Thomas, E-mail: thomas.lippert@psi.ch [Paul Scherrer Institute, CH-5232 Villigen PSI (Switzerland); Döbeli, Max [Laboratory of Ion Beam Physics, ETH Zurich, CH-8093 Zurich (Switzerland)

    2014-09-15

    Plasma chemistry and scattering strongly affect the congruent, elemental transfer during pulsed laser deposition of target metal species in an oxygen atmosphere. Studying the plasma properties of La{sub 0.6}Sr{sub 0.4}MnO{sub 3}, we demonstrate for as grown La{sub 0.6}Sr{sub 0.4}MnO{sub 3-δ} films that a congruent transfer of metallic species is achieved in two pressure windows: ∼10{sup −3} mbar and ∼2 × 10{sup −1} mbar. In the intermediate pressure range, La{sub 0.6}Sr{sub 0.4}MnO{sub 3-δ} becomes cation deficient and simultaneously almost fully stoichiometric in oxygen. Important for thin film growth is the presence of negative atomic oxygen and under which conditions positive metal-oxygen ions are created in the plasma. This insight into the plasma chemistry shows why the pressure window to obtain films with a desired composition and crystalline structure is narrow and requires a careful adjustment of the process parameters.

  14. Generation of uniform atmospheric pressure argon glow plasma by dielectric barrier discharge

    Indian Academy of Sciences (India)

    Raju Bhai Tyata; Deepak Prasad Subedi; Rajendra Shrestha; Chiow San Wong

    2013-03-01

    In this paper, atmospheric pressure glow discharges (APGD) in argon generated in parallel plate dielectric barrier discharge system is investigated by means of electrical and optical measurements. Using a high voltage (0–20 kV) power supply operating at 10–30 kHz, homogeneous and steady APGD has been observed between the electrodes with gap spacing from 0.5 mm to 2 mm and with a dielectric barrier of thickness 2 mm while argon gas is fed at a controlled flow rate of 11/min. The electron temperature and electron density of the plasma are determined by means of optical emission spectroscopy. Our results show that the electron density of the discharge obtained is of the order of 1016 cm-3 while the electron temperature is estimated to be 0.65 eV. The important result is that electron density determined from the line intensity ratio method and stark broadening method are in very good agreement. The Lissajous figure is used to estimate the energy deposited to the glow discharge. It is found that the energy deposited to the discharge is in the range of 20 to 25 $\\$J with a discharge voltage of 1.85 kV. The energy deposited to the discharge is observed to be higher at smaller gas spacing. The glow discharge plasma is tested to be effective in reducing the hydrophobicity of polyethylene film significantly.

  15. Coaxial carbon plasma gun deposition of amorphous carbon films

    Science.gov (United States)

    Sater, D. M.; Gulino, D. A.; Rutledge, S. K.

    1984-01-01

    A unique plasma gun employing coaxial carbon electrodes was used in an attempt to deposit thin films of amorphous diamond-like carbon. A number of different structural, compositional, and electrical characterization techniques were used to characterize these films. These included scanning electron microscopy, scanning transmission electron microscopy, X ray diffraction and absorption, spectrographic analysis, energy dispersive spectroscopy, and selected area electron diffraction. Optical absorption and electrical resistivity measurements were also performed. The films were determined to be primarily amorphous, with poor adhesion to fused silica substrates. Many inclusions of particulates were found to be present as well. Analysis of these particulates revealed the presence of trace impurities, such as Fe and Cu, which were also found in the graphite electrode material. The electrodes were the source of these impurities. No evidence of diamond-like crystallite structure was found in any of the film samples. Details of the apparatus, experimental procedure, and film characteristics are presented.

  16. Biomedical Applications of the Cold Atmospheric Plasma: Cell Responses

    Science.gov (United States)

    Volotskova, Olga

    Current breakthrough research on cold atmospheric plasma (CAP) demonstrates that CAP has great potential in various areas, including medicine and biology, thus providing a new tool for living tissue treatment. Depending on the configuration the cold plasma sources can be used in the following areas: wound healing, skin diseases, hospital hygiene, sterilization, antifungal treatments, dental care, cosmetics targeted cell/tissue removal, and cancer treatments. This dissertation is focused on the studies of biomedical applications of cold atmospheric plasma jet based on helium flow and resultant cell responses to the cold plasma treatment. The studies were carried out on extra-cellular and intra-cellular levels in vitro. The main practical applications are wound healing and alternative to existing cancer therapy methods, areas of great interest and significant challenges. The CAP jet was built in the Micropropulsion and Nanotechnology Laboratory of Dr. Michael Keidar, as a part of multidisciplinary collaboration with the GW Medical School (Dr. M.A. Stepp) concerned with plasma medicine and bioengineering studies. Normal and cancer cells have two fundamental behavioral properties, proliferation and motility, which can be evaluated through cell migration rates and cell cycle progression. Various microscopic, spectroscopic and flow cytometry techniques were used to characterize cell responses to the cold plasma treatment. It was found that CAP effect on the cells is localized within the area of the treatment (of around ˜ 5mm in diameter). The migration rates of the normal skin cells can be reduced up to ˜ 40%. However, depending on the cell type the required treatment time is different, thus differential treatment of various cells presented in tissue is possible. The CAP effect on the migration was explained through the changes of the cell surface proteins/integrins. It was also found that normal and cancer cells respond differently to the CAP treatment under the same

  17. Atmospheric pressure cold plasma treatment of cellulose based fillers for wood plastic composites

    Science.gov (United States)

    Lekobou, William; Englund, Karl; Pedrow, Patrick; Scudiero, Louis

    2011-10-01

    The main challenge of wood plastic composites (WPC) resides in the low interfacial adhesion due to incompatibility between the cellulose based filler that has a polar surface and most common matrixes, polyolefins which are non-polar. Plasma treatment is a promising technique for surface modification and its implementation into the processing of WPC would provide this industry with a versatile and nearly environmentally benign manufacturing tool. Our investigation aims at designing a cold atmospheric pressure plasma reactor for coating fillers with a hydrophobic material prior to compounding with the matrix. Deposition was achieved with our reactor that includes an array of high voltage needles, a grounded metal mesh, Ar as carrier gas and C2H2 as the precursor molecule. Parameters studied have included gas feed rates and applied voltage; FTIR, ESCA, AFM and SEM imaging were used for film diagnostics. We will also report on deposition rate and its dependence on radial and axial position as well as the effects of plasma-polymerized acetylene on the surface free energy of cellulose based substrates.

  18. Atmospheric deposition studies of heavy metals in Arctic by comparative analysis of lichens and cryoconite.

    Science.gov (United States)

    Singh, Shiv Mohan; Sharma, Jagdev; Gawas-Sakhalkar, Puja; Upadhyay, Ajay K; Naik, Simantini; Pedneker, Shailesh M; Ravindra, Rasik

    2013-02-01

    Lichens and cryoconite (rounded or granular, brownish-black debris occurring in holes on the glacier surface) from Ny-Ålesund were used for understanding the elemental deposition pattern in the area. Lichen samples collected from low-lying coastal region and cryoconite samples from high altitudinal glacier area were processed and analysed for elements such as aluminium (Al), arsenic (As), cadmium (Cd), cobalt (Co), chromium (Cr), cesium (Cs), copper (Cu), iron (Fe), manganese (Mn), nickel (Ni), lead (Pb), vanadium (V) and zinc (Zn) through inductively coupled plasma mass spectrometry. Results showed that heavy metals, Al and Fe, are present in high concentration in the cryoconite samples. Al was also present in high amounts in seven of the eight lichen samples studied. The general scheme of elements in the decreasing order of their concentrations for most of the cryoconite samples was Al > Fe > Mn > Zn > V > Pb > Cr > Ni > Cu > Co > As > Cs > Cd while that for the lichen samples was Al > Fe > Zn > Mn > Pb > Cu > Cs > Cr > Ni > V > Co > As > Cd. Similarity in trends in the two sample types confirms that the environment indeed contains these elements in that order of concentration which overtime got accumulated in the samples. Overall comparison showed most elements to be present in high concentrations in the cryoconite samples as compared to the lichen samples. Within the lichens, elemental accumulation data suggests that the low-lying site (L-2) from where Cladonia mediterranea sample was collected was the most polluted accumulating a number of elements at high concentrations. The probable reasons for such deposition patterns in the region could be natural (crustal contribution and sea salt spray) and anthropogenic (local and long-distance transmission of dust particles). In the future, this data can form a baseline for monitoring quantum of atmospheric heavy metal deposition in lichens and cryoconite of Svalbard, Arctic.

  19. Atmospheric pressure plasma jet-synthesized electrochromic organomolybdenum oxide thin films for flexible electrochromic devices

    Energy Technology Data Exchange (ETDEWEB)

    Lin, Yung-Sen, E-mail: yslin@fcu.edu.tw; Tsai, Tsung-Hsien; Tien, Shih-Wei

    2013-02-01

    An investigation is conducted into fast synthesis of electrochromic organomolybdenum oxide (MoO{sub x}C{sub y}) thin films onto 40 Ω/□ flexible polyethylene terephthalate/indium tin oxide substrates via atmospheric pressure plasma jet. A precursor [molybdenum carbonyl, Mo(CO){sub 6}] vapor, carried by argon gas, is injected into air plasma torch to synthesize MoO{sub x}C{sub y} films for offering extraordinary electrochromic performance. Only low driving voltages from − 1 V to 1 V are needed to offer reversible Li{sup +} ion intercalation and deintercalation in a 1 M LiClO{sub 4}-propylene carbonate electrolyte. Light modulation with transmittance variation of up to 61%, optical density change of 0.54 and coloration efficiency of 37.5 cm{sup 2}/C at a wavelength of 550 nm after 200 cycles of cyclic voltammetry switching measurements is achieved. - Highlights: ► Fast deposition of MoO{sub x}C{sub y} film by an atmospheric pressure plasma jet ► Organic–inorganic hybrid MoO{sub x}C{sub y} films synthesized ► Flexible and electrochromic MoO{sub x}C{sub y} films produced.

  20. Total Sulfur Deposition (wet+dry) from the Atmosphere

    Data.gov (United States)

    U.S. Environmental Protection Agency — Sulfur Dioxide (SO2) is emitted primarily as a by-product of coal combustion from power plants. Sulfur Dioxide reacts in the atmosphere to form other chemical such...

  1. High rate deposition of microcrystalline silicon films by high-pressure radio frequency plasma enhanced chemical vapor deposition (PECVD)

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    Hydrogenated microcrystalline silicon (μc-Si:H) thin films were prepared by high- pressure radio-frequency (13.56 MHz) plasma enhanced chemical vapor deposition (rf-PECVD) with a screened plasma. The deposition rate and crystallinity varying with the deposition pressure, rf power, hydrogen dilution ratio and electrodes distance were systematically studied. By optimizing the deposition parameters the device quality μc-Si:H films have been achieved with a high deposition rate of 7.8 /s at a high pressure. The Voc of 560 mV and the FF of 0.70 have been achieved for a single-junction μc-Si:H p-i-n solar cell at a deposition rate of 7.8 /s.

  2. High Temperature Multilayer Environmental Barrier Coatings Deposited Via Plasma Spray-Physical Vapor Deposition

    Science.gov (United States)

    Harder, Bryan James; Zhu, Dongming; Schmitt, Michael P.; Wolfe, Douglas E.

    2014-01-01

    Si-based ceramic matrix composites (CMCs) require environmental barrier coatings (EBCs) in combustion environments to avoid rapid material loss. Candidate EBC materials have use temperatures only marginally above current technology, but the addition of a columnar oxide topcoat can substantially increase the durability. Plasma Spray-Physical Vapor Deposition (PS-PVD) allows application of these multilayer EBCs in a single process. The PS-PVD technique is a unique method that combines conventional thermal spray and vapor phase methods, allowing for tailoring of thin, dense layers or columnar microstructures by varying deposition conditions. Multilayer coatings were deposited on CMC specimens and assessed for durability under high heat flux and load. Coated samples with surface temperatures ranging from 2400-2700F and 10 ksi loads using the high heat flux laser rigs at NASA Glenn. Coating morphology was characterized in the as-sprayed condition and after thermomechanical loading using electron microscopy and the phase structure was tracked using X-ray diffraction.

  3. A microwave plasma source for VUV atmospheric photochemistry

    Science.gov (United States)

    Tigrine, S.; Carrasco, N.; Vettier, L.; Cernogora, G.

    2016-10-01

    Microwave plasma discharges working at low pressure are nowadays a well-developed technique mainly used to provide radiation at different wavelengths. The aim of this work is to show that those discharges are an efficient windowless vacuum ultra-violet (VUV) photon source for planetary atmospheric photochemistry experiments. To do this, we use a surfatron-type discharge with a neon gas flow in the mbar pressure range coupled to a photochemical reactor. Working in the VUV range allows nitrogen-dominated atmospheres to be focused on (λ  <  100 nm). The experimental setup makes sure that no energy sources (electrons, metastable atoms) other than the VUV photons interact with the reactive medium. Neon has two resonance lines at 73.6 and 74.3 nm that behave differently depending on the pressure or power conditions. In parallel, the VUV photon flux emitted at 73.6 nm has been experimentally estimated in different pressure and power conditions, and varies in a large range between 2  ×  1013 ph s-1 cm-2 and 4  ×  1014 ph s-1 cm-2, which is comparable to a VUV synchrotron photon flux. Our first case study is the atmosphere of Titan and its N2-CH4 atmosphere. With this VUV source, the production of HCN and C2N2, two major Titan compounds, is detected, ensuring the suitability of the source for atmospheric photochemistry experiments.

  4. Magnetized neutron star atmospheres: beyond cool plasma approximation

    CERN Document Server

    Suleimanov, V F; Werner, K

    2012-01-01

    All the neutron star (NS) atmosphere models published so far have been calculated in the "cold plasma approximation", which neglects the relativistic effects in the radiative processes, such as cyclotron emission/absorption at harmonics of cyclotron frequency. Here we present new NS atmosphere models which include such effects. We calculate a set of models for effective temperatures T_eff =1-3 MK and magnetic fields B \\sim 10^{10}-10^{11} G, typical for the so-called central compact objects (CCOs) in supernova remnants, for which the electron cyclotron energy E_{c,e} and its first harmonics are in the observable soft X-ray range. Although the relativistic parameters, such as kT_eff /(m_e c^2) and E_{c,e} /(m_e c^2), are very small for CCOs, the relativistic effects substantially change the emergent spectra at the cyclotron resonances, E \\approx sE_{c,e} (s=1, 2,...). Although the cyclotron absorption features can form in a cold plasma due to the quantum oscillations of the free-free opacity, the shape and dep...

  5. Cancer therapy using non-thermal atmospheric pressure plasma with ultra-high electron density

    Energy Technology Data Exchange (ETDEWEB)

    Tanaka, Hiromasa [Institute of Innovation for Future Society, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan); Center for Advanced Medicine and Clinical Research, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Mizuno, Masaaki [Center for Advanced Medicine and Clinical Research, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Toyokuni, Shinya [Department of Pathology and Biological Responses, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Maruyama, Shoichi [Department of Nephrology, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Kodera, Yasuhiro [Department of Gastroenterological Surgery (Surgery II), Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Terasaki, Hiroko [Department of Ophthalmology, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Adachi, Tetsuo [Laboratory of Clinical Pharmaceutics, Gifu Pharmaceutical University, 501-1196 Gifu (Japan); Kato, Masashi [Department of Occupational and Environmental Health, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Kikkawa, Fumitaka [Department of Obstetrics and Gynecology, Nagoya University Graduate School of Medicine, Tsurumai-cho 65, Showa-ku, Nagoya 466-8550 (Japan); Hori, Masaru [Institute of Innovation for Future Society, Nagoya University, Furo-cho, Chikusa-ku, Nagoya 464-8603 (Japan)

    2015-12-15

    Cancer therapy using non-thermal atmospheric pressure plasma is a big challenge in plasma medicine. Reactive species generated from plasma are key factors for treating cancer cells, and thus, non-thermal atmospheric pressure plasma with high electron density has been developed and applied for cancer treatment. Various cancer cell lines have been treated with plasma, and non-thermal atmospheric plasma clearly has anti-tumor effects. Recent innovative studies suggest that plasma can both directly and indirectly affect cells and tissues, and this observation has widened the range of applications. Thus, cancer therapy using non-thermal atmospheric pressure plasma is promising. Animal experiments and understanding the mode of action are essential for clinical application in the future. A new academic field that combines plasma science, the biology of free radicals, and systems biology will be established.

  6. Cancer therapy using non-thermal atmospheric pressure plasma with ultra-high electron density

    Science.gov (United States)

    Tanaka, Hiromasa; Mizuno, Masaaki; Toyokuni, Shinya; Maruyama, Shoichi; Kodera, Yasuhiro; Terasaki, Hiroko; Adachi, Tetsuo; Kato, Masashi; Kikkawa, Fumitaka; Hori, Masaru

    2015-12-01

    Cancer therapy using non-thermal atmospheric pressure plasma is a big challenge in plasma medicine. Reactive species generated from plasma are key factors for treating cancer cells, and thus, non-thermal atmospheric pressure plasma with high electron density has been developed and applied for cancer treatment. Various cancer cell lines have been treated with plasma, and non-thermal atmospheric plasma clearly has anti-tumor effects. Recent innovative studies suggest that plasma can both directly and indirectly affect cells and tissues, and this observation has widened the range of applications. Thus, cancer therapy using non-thermal atmospheric pressure plasma is promising. Animal experiments and understanding the mode of action are essential for clinical application in the future. A new academic field that combines plasma science, the biology of free radicals, and systems biology will be established.

  7. Source receptor relations for the calculation of atmospheric deposition to the North Sea: Nitrogen and Cadmium

    NARCIS (Netherlands)

    van Jaarsveld JA; de Leeuw FAAM

    1993-01-01

    In this report a simplified atmospheric transport model for estimating the deposition of nitrogen (both NOx and NHx) and cadmium to the North Sea is presented. In this so-called meta-model a linear relationship between the emissions from a source area and the resulting deposition at receptor points

  8. Ti-doped hydrogenated diamond like carbon coating deposited by hybrid physical vapor deposition and plasma enhanced chemical vapor deposition

    Science.gov (United States)

    Lee, Na Rae; Sle Jun, Yee; Moon, Kyoung Il; Sunyong Lee, Caroline

    2017-03-01

    Diamond-like carbon films containing titanium and hydrogen (Ti-doped DLC:H) were synthesized using a hybrid technique based on physical vapor deposition (PVD) and plasma enhanced chemical vapor deposition (PECVD). The film was deposited under a mixture of argon (Ar) and acetylene gas (C2H2). The amount of Ti in the Ti-doped DLC:H film was controlled by varying the DC power of the Ti sputtering target ranging from 0 to 240 W. The composition, microstructure, mechanical and chemical properties of Ti-doped DLC:H films with varying Ti concentrations, were investigated using Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), nano indentation, a ball-on-disk tribometer, a four-point probe system and dynamic anodic testing. As a result, the optimum composition of Ti in Ti-doped DLC:H film using our hybrid method was found to be a Ti content of 18 at. %, having superior electrical conductivity and high corrosion resistance, suitable for bipolar plates. Its hardness value was measured to be 25.6 GPa with a low friction factor.

  9. Quantifying atmospheric nitrogen deposition through a nationwide monitoring network across China

    Directory of Open Access Journals (Sweden)

    W. Xu

    2015-07-01

    Full Text Available Global reactive nitrogen (Nr deposition to terrestrial ecosystems has increased dramatically since the industrial revolution. This is especially true in recent decades in China due to continuous economic growth. However, there are no comprehensive reports of both measured dry and wet Nr deposition across China. We therefore conducted a multiple-year study during the period mainly from 2010 to 2014 to monitor atmospheric concentrations of five major Nr species of gaseous NH3, NO2 and HNO3, and inorganic nitrogen (NH4+ and NO3− in both particles and precipitation, based on a Nationwide Nitrogen Deposition Monitoring Network (NNDMN, covering 43 sites in China. Wet deposition fluxes of Nr species were measured directly; dry deposition fluxes were estimated using airborne concentration measurements and inferential models. Our observations reveal large spatial variations of atmospheric Nr concentrations and dry and wet Nr deposition. The annual average concentrations (1.3–47.0 μg N m−3 and dry plus wet deposition fluxes (2.9–75.2 kg N ha−1 yr−1 of inorganic Nr species ranked by region as North China > Southeast China > Southwest China > Northeast China > Northwest China > the Tibetan Plateau or by land use as urban > rural > background sites, reflecting the impact of anthropogenic Nr emission. Average dry and wet N deposition fluxes were 18.5 and 19.3 kg N ha−1 yr−1, respectively, across China, with reduced N deposition dominating both dry and wet deposition. Our results suggest atmospheric dry N deposition is equally important to wet N deposition at the national scale and both deposition forms should be included when considering the impacts of N deposition on environment and ecosystem health.

  10. Dissolved organic nitrogen dominates in European bogs under increasing atmospheric N deposition

    NARCIS (Netherlands)

    Bragazza, L.; Limpens, J.

    2004-01-01

    To assess the effects of increased atmospheric N input on N availability in ombrotrophic peatlands, the relative concentrations of dissolved organic nitrogen (DON) to dissolved inorganic nitrogen (DIN) were measured in bog waters along a natural gradient of atmospheric N deposition. Six European bog

  11. Biogeochemical context impacts seawater pH changes resulting from atmospheric sulfur and nitrogen deposition

    NARCIS (Netherlands)

    Hagens, M.|info:eu-repo/dai/nl/357426274; Hunter, K.A.; Liss, P.S.; Middelburg, J.J.|info:eu-repo/dai/nl/079665373

    2014-01-01

    Seawater acidification can be induced both by absorption of atmospheric carbon dioxide (CO2) and by atmospheric deposition of sulfur and nitrogen oxides and ammonia. Their relative significance, interplay, and dependency on water column biogeochemistry are not well understood. Using a simple biogeoc

  12. Impact of food model (micro)structure on the microbial inactivation efficacy of cold atmospheric plasma.

    Science.gov (United States)

    Smet, C; Noriega, E; Rosier, F; Walsh, J L; Valdramidis, V P; Van Impe, J F

    2017-01-02

    The large potential of cold atmospheric plasma (CAP) for food decontamination has recently been recognized. Room-temperature gas plasmas can decontaminate foods without causing undesired changes. This innovative technology is a promising alternative for treating fresh produce. However, more fundamental studies are needed before its application in the food industry. The impact of the food structure on CAP decontamination efficacy of Salmonella Typhimurium and Listeria monocytogenes was studied. Cells were grown planktonically or as surface colonies in/on model systems. Both microorganisms were grown in lab culture media in petri dishes at 20°C until cells reached the stationary phase. Before CAP treatment, cells were deposited in a liquid carrier, on a solid(like) surface or on a filter. A dielectric barrier discharge reactor generated helium-oxygen plasma, which was used to treat samples up to 10min. Although L. monocytogenes is more resistant to CAP treatment, similar trends in inactivation behavior as for S. Typhimurium are observed, with log reductions in the range [1.0-2.9] for S. Typhimurium and [0.2-2.2] for L. monocytogenes. For both microorganisms, cells grown planktonically are easily inactivated, as compared to surface colonies. More stressing growth conditions, due to cell immobilization, result in more resistant cells during CAP treatment. The main difference between the inactivation support systems is the absence or presence of a shoulder phase. For experiments in the liquid carrier, which exhibit a long shoulder, the plasma components need to diffuse and penetrate through the medium. This explains the higher efficacies of CAP treatment on cells deposited on a solid(like) surface or on a filter. This research demonstrates that the food structure influences the cell inactivation behavior and efficacy of CAP, and indicates that food intrinsic factors need to be accounted when designing plasma treatment.

  13. Microstructure and mechanical properties of nickel-chrome-bor-silicon layers produced by the atmospheric plasma spray process

    Directory of Open Access Journals (Sweden)

    Mihailo R. Mrdak

    2012-01-01

    Full Text Available This paper analyzes the influence of plasma spray parameters on the microstructure and mechanical properties of NiCrBSi coatings deposited by the atmospheric plasma spray (APS process. The microstructure and mechanical properties of plasma spray coatings are determined by the interaction of plasma ions with powder particles when the rate and temperature of plasma particles are transferred to powder particles. The interaction effect directly depends on the time the powder particles spend in plasma, and that time is defined by the deposition distance for each type of powder, depending on the grain size, melting temperature and specific mass. In order to obtain homogeneous and dense coatings, three distances (70,120 and 170 mm from the substrate were used in the research. The coating of the best structural and mechanical characteristics was remelted and fused to the base in order to obtain a better structure. Self - fluxing NiCrBSi alloys are widely used because of the good resistance of boride, carbide and silicide solid phases to wear and corrosion. The morphology of powder particles was examined in the SEM (Scanning Electron Microscope, while the microstructure of the layers was assessed using a light microscope. The microstructural analysis of the deposited layers was performed in accordance with the Pratt-Whitney standard. The mechanical properties of the layers were assessed by applying the HV0.3 method for microhardness testing and tensile testing was applied to test bond strength.

  14. Modeling the global atmospheric transport and deposition of mercury to the Great Lakes

    Directory of Open Access Journals (Sweden)

    Mark D. Cohen

    2016-07-01

    Full Text Available Abstract Mercury contamination in the Great Lakes continues to have important public health and wildlife ecotoxicology impacts, and atmospheric deposition is a significant ongoing loading pathway. The objective of this study was to estimate the amount and source-attribution for atmospheric mercury deposition to each lake, information needed to prioritize amelioration efforts. A new global, Eulerian version of the HYSPLIT-Hg model was used to simulate the 2005 global atmospheric transport and deposition of mercury to the Great Lakes. In addition to the base case, 10 alternative model configurations were used to examine sensitivity to uncertainties in atmospheric mercury chemistry and surface exchange. A novel atmospheric lifetime analysis was used to characterize fate and transport processes within the model. Model-estimated wet deposition and atmospheric concentrations of gaseous elemental mercury (Hg(0 were generally within ∼10% of measurements in the Great Lakes region. The model overestimated non-Hg(0 concentrations by a factor of 2–3, similar to other modeling studies. Potential reasons for this disagreement include model inaccuracies, differences in atmospheric Hg fractions being compared, and the measurements being biased low. Lake Erie, downwind of significant local/regional emissions sources, was estimated by the model to be the most impacted by direct anthropogenic emissions (58% of the base case total deposition, while Lake Superior, with the fewest upwind local/regional sources, was the least impacted (27%. The U.S. was the largest national contributor, followed by China, contributing 25% and 6%, respectively, on average, for the Great Lakes. The contribution of U.S. direct anthropogenic emissions to total mercury deposition varied between 46% for the base case (with a range of 24–51% over all model configurations for Lake Erie and 11% (range 6–13% for Lake Superior. These results illustrate the importance of atmospheric

  15. Influence of the voltage waveform during nanocomposite layer deposition by aerosol-assisted atmospheric pressure Townsend discharge

    Science.gov (United States)

    Profili, J.; Levasseur, O.; Naudé, N.; Chaneac, C.; Stafford, L.; Gherardi, N.

    2016-08-01

    This work examines the growth dynamics of TiO2-SiO2 nanocomposite coatings in plane-to-plane Dielectric Barrier Discharges (DBDs) at atmospheric pressure operated in a Townsend regime using nebulized TiO2 colloidal suspension in hexamethyldisiloxane as the growth precursors. For low-frequency (LF) sinusoidal voltages applied to the DBD cell, with voltage amplitudes lower than the one required for discharge breakdown, Scanning Electron Microscopy of silicon substrates placed on the bottom DBD electrode reveals significant deposition of TiO2 nanoparticles (NPs) close to the discharge entrance. On the other hand, at higher frequencies (HF), the number of TiO2 NPs deposited strongly decreases due to their "trapping" in the oscillating voltage and their transport along the gas flow lines. Based on these findings, a combined LF-HF voltage waveform is proposed and used to achieve significant and spatially uniform deposition of TiO2 NPs across the whole substrate surface. For higher voltage amplitudes, in the presence of hexamethyldisiloxane and nitrous oxide for plasma-enhanced chemical vapor deposition of inorganic layers, it is found that TiO2 NPs become fully embedded into a silica-like matrix. Similar Raman spectra are obtained for as-prepared TiO2 NPs and for nanocomposite TiO2-SiO2 coating, suggesting that plasma exposure does not significantly alter the crystalline structure of the TiO2 NPs injected into the discharge.

  16. Cold atmospheric plasma decontamination of the pericarps of fruit.

    Science.gov (United States)

    Perni, Stefano; Liu, David W; Shama, Gilbert; Kong, Michael G

    2008-02-01

    This investigation describes the inactivation by cold atmospheric plasmas of one pathogenic and three spoilage organisms on the pericarps of mangoes and melons. The operating voltage necessary for efficient microbial decontamination of fruit pericarps was first established using Escherichia coli at a concentration of 10(7) CFU/cm2 on the surface of mango. It was found that, when the plasma was sustained slightly above its breakdown voltage of 12 kV (peak to peak), no inactivation was detected when cells were plated onto tryptone soya extract agar (TSA). However, when plated onto eosin methylene blue agar, sublethal injury corresponding to approximately 1 log reduction was achieved, whereas on TSA supplemented with 4% NaCl a greater reduction of 1.5 log was revealed. When the voltage was increased by 33% to 16 kV, a reduction in cell counts of 3 log was achieved on all three plating media. Further investigations at these new operating conditions were conducted using a range of spoilage microorganisms (Saccharomyces cerevisae, Pantoea agglomerans, and Gluconacetobacter liquefaciens) all at a surface concentration of 106 CFU/cm2 on the pericarps of mango and melon. P. agglomerans and G. liquefaciens were reduced below the detection limit (corresponding to 3 log) after only 2.5 s on both fruits, whereas E. coli required 5 s to reach the same level of inactivation. S. cerevisae was the most resistant organism studied and was reduced in numbers below the detection limit after 10 s on mango and 30 s on melon. The optical emission spectra generated by the cold atmospheric plasma at both high and low operating voltages were compared in order to identify putative lethal species. It was shown that an increase in the applied voltage led to more efficient production of reactive plasma species, particularly oxygen atoms, and the production of oxygen atoms was related to the level of bacterial inactivation achieved. Production of atomic oxygen could be used as an indicator of

  17. Atmospheric Deposition: Sampling Procedures, Analytical Methods, and Main Recent Findings from the Scientific Literature

    Directory of Open Access Journals (Sweden)

    M. Amodio

    2014-01-01

    Full Text Available The atmosphere is a carrier on which some natural and anthropogenic organic and inorganic chemicals are transported, and the wet and dry deposition events are the most important processes that remove those chemicals, depositing it on soil and water. A wide variety of different collectors were tested to evaluate site-specificity, seasonality and daily variability of settleable particle concentrations. Deposition fluxes of POPs showed spatial and seasonal variations, diagnostic ratios of PAHs on deposited particles, allowed the discrimination between pyrolytic or petrogenic sources. Congener pattern analysis and bulk deposition fluxes in rural sites confirmed long-range atmospheric transport of PCDDs/Fs. More and more sophisticated and newly designed deposition samplers have being used for characterization of deposited mercury, demonstrating the importance of rain scavenging and the relatively higher magnitude of Hg deposition from Chinese anthropogenic sources. Recently biological monitors demonstrated that PAH concentrations in lichens were comparable with concentrations measured in a conventional active sampler in an outdoor environment. In this review the authors explore the methodological approaches used for the assessment of atmospheric deposition, from the analysis of the sampling methods, the analytical procedures for chemical characterization of pollutants and the main results from the scientific literature.

  18. Power modulation in an atmospheric pressure plasma jet

    Science.gov (United States)

    Kelly, S.; Turner, M. M.

    2014-12-01

    Power modulation in an atmospheric pressure capacitively coupled radio frequency plasma jet is investigated by numerical modelling. The dynamics of successively pulsing the applied power on and off for a helium-oxygen (˜0.6%) plasma is investigated. The impact of power pulsing on reactive species generation and gas heating is discussed with control opportunities emphasized. Power modulation shows linear control for reactive species and heat flux delivery to a treatment surface above an initial phase of power growth. Power is found to be coupled primarily to the electrons with electron loss rates determining the interference between successive power modulation phases. Plasma decay in the power off phase is characterized by a large initial electron loss in the first 0.5 µs followed by ambipolar decay dominated by ions of opposite charge. Power modulation effects on gas heating show a larger range of temperature control when compared with convection cooling. Reactive oxygen species reaching a treatment surface are shown to typically vary over an order of magnitude for variation in the duty cycle.

  19. Characteristics of silicon nitride deposited by VHF (162 MHz)-plasma enhanced chemical vapor deposition using a multi-tile push-pull plasma source

    Science.gov (United States)

    Kim, Ki Seok; Sirse, Nishant; Kim, Ki Hyun; Rogers Ellingboe, Albert; Kim, Kyong Nam; Yeom, Geun Young

    2016-10-01

    To prevent moisture and oxygen permeation into flexible organic electronic devices formed on substrates, the deposition of an inorganic diffusion barrier material such as SiN x is important for thin film encapsulation. In this study, by a very high frequency (162 MHz) plasma-enhanced chemical vapor deposition (VHF-PECVD) using a multi-tile push-pull plasma source, SiN x layers were deposited with a gas mixture of NH3/SiH4 with/without N2 and the characteristics of the plasma and the deposited SiN x film as the thin film barrier were investigated. Compared to a lower frequency (60 MHz) plasma, the VHF (162 MHz) multi-tile push-pull plasma showed a lower electron temperature, a higher vibrational temperature, and higher N2 dissociation for an N2 plasma. When a SiN x layer was deposited with a mixture of NH3/SiH4 with N2 at a low temperature of 100 °C, a stoichiometric amorphous Si3N4 layer with very low Si-H bonding could be deposited. The 300 nm thick SiN x film exhibited a low water vapor transmission rate of 1.18  ×  10-4 g (m2 · d)-1, in addition to an optical transmittance of higher than 90%.

  20. In-situ monitoring of etching of bovine serum albumin using low-temperature atmospheric plasma jet

    Science.gov (United States)

    Kousal, J.; Shelemin, A.; Kylián, O.; Slavínská, D.; Biederman, H.

    2017-01-01

    Bio-decontamination of surfaces by means of atmospheric pressure plasma is nowadays extensively studied as it represents promising alternative to commonly used sterilization/decontamination techniques. The non-equilibrium atmospheric pressure plasmas were already reported to be highly effective in removal of a wide range of biological residual from surfaces. Nevertheless the kinetics of removal of biological contamination from surfaces is still not well understood as the majority of performed studies were based on ex-situ evaluation of etching rates, which did not allow investigating details of plasma action on biomolecules. This study therefore presents a real-time, in-situ ellipsometric characterization of removal of bovine serum albumin (BSA) from surfaces by low-temperature atmospheric plasma jet operated in argon. Non-linear and at shorter distances between treated samples and nozzle of the plasma jet also non-monotonic dependence of the removal rate on the treatment duration was observed. According to additional measurements focused on the determination of chemical changes of treated BSA as well as temperature measurements, the observed behavior is most likely connected with two opposing effects: the formation of a thin layer on the top of BSA deposit enriched in inorganic compounds, whose presence causes a gradual decrease of removal efficiency, and slight heating of BSA that facilitates its degradation and volatilization induced by chemically active radicals produced by the plasma.

  1. Development of a radio frequency atmospheric pressure plasma jet for diamond-like carbon coatings on stainless steel substrates

    Science.gov (United States)

    Sohbatzadeh, F.; Samadi, O.; Siadati, S. N.; Etaati, G. R.; Asadi, E.; Safari, R.

    2016-10-01

    In this paper, an atmospheric pressure plasma jet with capacitively coupled radio frequency discharge was developed for diamond-like carbon (DLC) coatings on stainless steel substrates. The plasma jet was generated by argon-methane mixture and its physical parameters were investigated. Relation between the plasma jet length and width of the powered electrode was discussed. Optical and electrical characteristics were studied by optical emission spectroscopy, voltage and current probes, respectively. The evolutions of various species like ArI, C2 and CH along the jet axis were investigated. Electron temperature and density were estimated by Boltzmann plot method and Saha-Boltzmann equation, respectively. Finally, a diamond-like carbon coating was deposited on stainless steel-304 substrates by the atmospheric pressure radio frequency plasma jet in ambient air. Raman spectroscopy, scanning electron microscopy (SEM), atomic force microscopy and Vickers hardness test were used to study the deposited films. The length of the jet was increased by increasing the width of the powered electrode. The estimated electron temperature and density were 1.43 eV and 1.39 × 1015 cm-3, respectively. Averaged Vicker's hardness of the coated sample was three times greater than that of the substrate. The SEM images of the deposited thin films revealed a 4.5 μm DLC coated for 20 min.

  2. Atmospheric deposition of {sup 137}Cs between 1994 and 2002 at Cienfuegos, Cuba

    Energy Technology Data Exchange (ETDEWEB)

    Alonso-Hernandez, C.M. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba)]. E-mail: carlos@ceac.perla.inf.cu; Cartas-Aguila, H. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba); Diaz-Asencio, M. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba); Munoz-Caravaca, A. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba); Martin-Perez, J. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba); Sibello-Hernandez, R. [Centro de Estudios Ambientales de Cienfuegos, AP 5. Ciudad Nuclear, Cienfuegos (Cuba)

    2006-07-01

    Levels of {sup 137}Cs in total atmospheric deposition have been measured in the Cienfuegos region (Cuba) between 1994 and 2002. Samples were collected every three months, evaporated to dryness to obtain residual samples, and measured by gamma spectrometry. The {sup 137}Cs mean concentration in total deposition was 0.24 Bq m{sup -2} and data ranged between <0.05 and 0.62 Bq m{sup -2}. Precipitation rates and raintime have proved to be the most important factors controlling the concentration and depositional flux of {sup 137}Cs in the atmosphere over Cienfuegos, showing a high correlation coefficient (R = 0.93)

  3. Practical silicon deposition rules derived from silane monitoring during plasma-enhanced chemical vapor deposition

    Energy Technology Data Exchange (ETDEWEB)

    Bartlome, Richard, E-mail: richard.bartlome@alumni.ethz.ch; De Wolf, Stefaan; Demaurex, Bénédicte; Ballif, Christophe [Ecole Polytechnique Fédérale de Lausanne (EPFL), Institute of Microengineering (IMT), Photovoltaics and Thin-Film Electronics Laboratory, Rue de la Maladière 71b, 2000 Neuchâtel (Switzerland); Amanatides, Eleftherios; Mataras, Dimitrios [University of Patras, Department of Chemical Engineering, Plasma Technology Laboratory, P.O. Box 1407, 26504 Patras (Greece)

    2015-05-28

    We clarify the difference between the SiH{sub 4} consumption efficiency η and the SiH{sub 4} depletion fraction D, as measured in the pumping line and the actual reactor of an industrial plasma-enhanced chemical vapor deposition system. In the absence of significant polysilane and powder formation, η is proportional to the film growth rate. Above a certain powder formation threshold, any additional amount of SiH{sub 4} consumed translates into increased powder formation rather than into a faster growing Si film. In order to discuss a zero-dimensional analytical model and a two-dimensional numerical model, we measure η as a function of the radio frequency (RF) power density coupled into the plasma, the total gas flow rate, the input SiH{sub 4} concentration, and the reactor pressure. The adjunction of a small trimethylboron flow rate increases η and reduces the formation of powder, while the adjunction of a small disilane flow rate decreases η and favors the formation of powder. Unlike η, D is a location-dependent quantity. It is related to the SiH{sub 4} concentration in the plasma c{sub p}, and to the phase of the growing Si film, whether the substrate is glass or a c-Si wafer. In order to investigate transient effects due to the RF matching, the precoating of reactor walls, or the introduction of a purifier in the gas line, we measure the gas residence time and acquire time-resolved SiH{sub 4} density measurements throughout the ignition and the termination of a plasma.

  4. High rate (∼7 nm/s), atmospheric pressure deposition of ZnO front electrode for Cu(In,Ga)Se2 thin-film solar cells with efficiency beyond 15%

    NARCIS (Netherlands)

    Illiberi, A.; Grob, F.; Frijters, C.; Poodt, P.; Ramachandra, R.; Winands, H.; Simor, M.; Bolt, P.J.

    2013-01-01

    Undoped zinc oxide (ZnO) films have been grown on a moving glass substrate by plasma-enhanced chemical vapor deposition at atmospheric pressure. High deposition rates of ∼7 nm/s are achieved at low temperature (200°C) for a substrate speed from 20 to 60 mm/min. ZnO films are highly transparent in th

  5. High rate (∼7 nm/s), atmospheric pressure deposition of ZnO front electrode for Cu(In,Ga)Se2 thin-film solar cells with efficiency beyond 15%

    NARCIS (Netherlands)

    Illiberi, A.; Grob, F.; Frijters, C.; Poodt, P.; Ramachandra, R.; Winands, H.; Simor, M.; Bolt, P.J.

    2013-01-01

    Undoped zinc oxide (ZnO) films have been grown on a moving glass substrate by plasma-enhanced chemical vapor deposition at atmospheric pressure. High deposition rates of ∼7 nm/s are achieved at low temperature (200°C) for a substrate speed from 20 to 60 mm/min. ZnO films are highly transparent in

  6. Surface chemical changes of atmospheric pressure plasma treated rabbit fibres important for felting process

    Energy Technology Data Exchange (ETDEWEB)

    Štěpánová, Vlasta, E-mail: vstepanova@mail.muni.cz [Department of Physical Electronics, Faculty of Science Masaryk University, Kotlářská 2, 611 37 Brno (Czech Republic); Slavíček, Pavel; Stupavská, Monika; Jurmanová, Jana [Department of Physical Electronics, Faculty of Science Masaryk University, Kotlářská 2, 611 37 Brno (Czech Republic); Černák, Mirko [Department of Physical Electronics, Faculty of Science Masaryk University, Kotlářská 2, 611 37 Brno (Czech Republic); Department of Experimental Physics, Faculty of Mathematics, Physics and Informatics, Comenius University, Mlynská dolina F2, 842 48 Bratislava (Slovakia)

    2015-11-15

    Graphical abstract: - Highlights: • Rabbit fibres plasma treatment is an effective method for fibres modification. • Atmospheric pressure plasma treatment is able to affect fibres properties. • Surface changes on fibres after plasma treatment were analysed via SEM, ATR-FTIR, XPS. • Significant increase of fibres wettability after plasma treatment was observed. • Plasma treatment at atmospheric pressure can replace the chemical treatment of fibres. - Abstract: We introduce the atmospheric pressure plasma treatment as a suitable procedure for in-line industrial application of rabbit fibres pre-treatment. Changes of rabbit fibre properties due to the plasma treatment were studied in order to develop new technology of plasma-based treatment before felting. Diffuse Coplanar Surface Barrier Discharge (DCSBD) in ambient air at atmospheric pressure was used for plasma treatment. Scanning electron microscopy was used for determination of the fibres morphology before and after plasma treatment. X-ray photoelectron spectroscopy and attenuated total reflectance-Fourier transform infrared spectroscopy were used for evaluation of reactive groups. The concentration of carbon decreased and conversely the concentration of nitrogen and oxygen increased after plasma treatment. Aging effect of plasma treated fibres was also investigated. Using Washburn method the significant increase of fibres wettability was observed after plasma treatment. New approach of pre-treatment of fibres before felting using plasma was developed. Plasma treatment of fibres at atmospheric pressure can replace the chemical method which consists of application of strong acids on fibres.

  7. Use of Atmospheric-Pressure Plasma Jet for Polymer Surface Modification: An Overview

    Energy Technology Data Exchange (ETDEWEB)

    Kuettner, Lindsey A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-03-16

    Atmospheric-pressure plasma jets (APPJs) are playing an increasingly important role in materials processing procedures. Plasma treatment is a useful tool to modify surface properties of materials, especially polymers. Plasma reacts with polymer surfaces in numerous ways thus the type of process gas and plasma conditions must be explored for chosen substrates and materials to maximize desired properties. This report discusses plasma treatments and looks further into atmospheric-pressure plasma jets and the effects of gases and plasma conditions. Following the short literature review, a general overview of the future work and research at Los Alamos National Laboratory (LANL) is discussed.

  8. Atmospheric deposition of semivolatile organic compounds to plants

    NARCIS (Netherlands)

    Bakker, Martine Inez

    2000-01-01

    This thesis describes how the deposition of semivolatile organic compounds (SOCs) to plant surfaces is affected by the characteristics of the plant. From a literature review, it was concluded that differences between SOC concentrations in different plant species are often very small (< a factor

  9. Plasma-enhanced Chemical Vapor Deposition of Aluminum Oxide Using Ultrashort Precursor Injection Pulses

    NARCIS (Netherlands)

    Dingemans, G.; M. C. M. van de Sanden,; Kessels, W. M. M.

    2012-01-01

    An alternative plasma-enhanced chemical vapor deposition (PECVD) method is developed and applied for the deposition of high-quality aluminum oxide (AlOx) films. The PECVD method combines a continuous plasma with ultrashort precursor injection pulses. We demonstrate that the modulation of the precurs

  10. SEM study on the deposition of coal pyrolysis in arc plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Y.J.; Chen, H.G.; Yan, Y.L.; Lu, Y.K.; Li, F.; Xie, K.C. [Taiyuan University of Technology, Taiyuan (China). Shanxi Key Lab of Coal Science and Technology

    1999-07-01

    During coal pyrolysis in hydrogen plasma, residue was deposited on the reactor wall. Scanning electron microscopy indicated that metaplast were formed during the process. The mechanism of formation of deposits, their morphology, porosity and mechanical properties are discussed. It was shown that particles do not blend with plasma under these operation conditions. 4 refs., 5 figs., 2 tabs.

  11. Reduction and degradation of amyloid aggregates by a pulsed radio-frequency cold atmospheric plasma jet

    Energy Technology Data Exchange (ETDEWEB)

    Bayliss, D L; Walsh, J L; Iza, F; Kong, M G [Department of Electronic and Electrical Engineering, Loughborough University, Leicestershire LE11 3TU (United Kingdom); Shama, G [Department of Chemical Engineering, Loughborough University, Leicestershire LE11 3TU (United Kingdom)], E-mail: m.g.kong@lboro.ac.uk

    2009-11-15

    Surface-borne amyloid aggregates with mature fibrils are used as a non-infectious prion model to evaluate cold atmospheric plasmas (CAPs) as a prion inactivation strategy. Using a helium-oxygen CAP jet with pulsed radio-frequency (RF) excitation, amyloid aggregates deposited on freshly cleaved mica discs are reduced substantially leaving only a few spherical fragments of sub-micrometer sizes in areas directly treated by the CAP jet. Outside the light-emitting part of the CAP jet, plasma treatment results in a 'skeleton' of much reduced amyloid stacks with clear evidence of fibril fragmentation. Analysis of possible plasma species and the physical configuration of the jet-sample interaction suggests that the skeleton structures observed are unlikely to have arisen as a result of physical forces of detachment, but instead by progressive diffusion of oxidizing plasma species into porous amyloid aggregates. Composition of chemical bonds of this reduced amyloid sample is very different from that of intact amyloid aggregates. These suggest the possibility of on-site degradation by CAP treatment with little possibility of spreading contamination elsewhere , thus offering a new reaction chemistry route to protein infectivity control with desirable implications for the practical implementation of CAP-based sterilization systems.

  12. Reduction and degradation of amyloid aggregates by a pulsed radio-frequency cold atmospheric plasma jet

    Science.gov (United States)

    Bayliss, D. L.; Walsh, J. L.; Shama, G.; Iza, F.; Kong, M. G.

    2009-11-01

    Surface-borne amyloid aggregates with mature fibrils are used as a non-infectious prion model to evaluate cold atmospheric plasmas (CAPs) as a prion inactivation strategy. Using a helium-oxygen CAP jet with pulsed radio-frequency (RF) excitation, amyloid aggregates deposited on freshly cleaved mica discs are reduced substantially leaving only a few spherical fragments of sub-micrometer sizes in areas directly treated by the CAP jet. Outside the light-emitting part of the CAP jet, plasma treatment results in a 'skeleton' of much reduced amyloid stacks with clear evidence of fibril fragmentation. Analysis of possible plasma species and the physical configuration of the jet-sample interaction suggests that the skeleton structures observed are unlikely to have arisen as a result of physical forces of detachment, but instead by progressive diffusion of oxidizing plasma species into porous amyloid aggregates. Composition of chemical bonds of this reduced amyloid sample is very different from that of intact amyloid aggregates. These suggest the possibility of on-site degradation by CAP treatment with little possibility of spreading contamination elsewhere , thus offering a new reaction chemistry route to protein infectivity control with desirable implications for the practical implementation of CAP-based sterilization systems.

  13. Cold Atmospheric Plasma: methods of production and application in dentistry and oncology

    OpenAIRE

    Hoffmann, Clotilde; Berganza, Carlos; Zhang, John

    2013-01-01

    Cold Atmospheric Plasma is an ionized gas that has recently been extensively studied by researchers as a possible therapy in dentistry and oncology. Several different gases can be used to produce Cold Atmospheric Plasma such as Helium, Argon, Nitrogen, Heliox, and air. There are many methods of production by which cold atmospheric plasma is created. Each unique method can be used in different biomedical areas. In dentistry, researchers have mostly investigated the antimicrobial effects produc...

  14. Helium atmospheric pressure plasma jets touching dielectric and metal surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Norberg, Seth A., E-mail: norbergs@umich.edu; Johnsen, Eric, E-mail: ejohnsen@umich.edu [Department of Mechanical Engineering, University of Michigan, 2350 Hayward Street, Ann Arbor, Michigan 48109-2125 (United States); Kushner, Mark J., E-mail: mjkush@umich.edu [Department of Electrical Engineering and Computer Science, University of Michigan, 1301 Beal Avenue, Ann Arbor, Michigan 48109-2122 (United States)

    2015-07-07

    Atmospheric pressure plasma jets (APPJs) are being investigated in the context plasma medicine and biotechnology applications, and surface functionalization. The composition of the surface being treated ranges from plastics, liquids, and biological tissue, to metals. The dielectric constant of these materials ranges from as low as 1.5 for plastics to near 80 for liquids, and essentially infinite for metals. The electrical properties of the surface are not independent variables as the permittivity of the material being treated has an effect on the dynamics of the incident APPJ. In this paper, results are discussed from a computational investigation of the interaction of an APPJ incident onto materials of varying permittivity, and their impact on the discharge dynamics of the plasma jet. The computer model used in this investigation solves Poisson's equation, transport equations for charged and neutral species, the electron energy equation, and the Navier-Stokes equations for the neutral gas flow. The APPJ is sustained in He/O{sub 2} = 99.8/0.2 flowing into humid air, and is directed onto dielectric surfaces in contact with ground with dielectric constants ranging from 2 to 80, and a grounded metal surface. Low values of relative permittivity encourage propagation of the electric field into the treated material and formation and propagation of a surface ionization wave. High values of relative permittivity promote the restrike of the ionization wave and the formation of a conduction channel between the plasma discharge and the treated surface. The distribution of space charge surrounding the APPJ is discussed.

  15. One-dimensional electromagnetic band gap plasma structure formed by atmospheric pressure plasma inhomogeneities

    Science.gov (United States)

    Babitski, V. S.; Callegari, Th.; Simonchik, L. V.; Sokoloff, J.; Usachonak, M. S.

    2017-08-01

    The ability to use plasma columns of pulse discharges in argon at atmospheric pressure to form a one-dimensional electromagnetic band gap structure (or electromagnetic crystal) in the X-band waveguide is demonstrated. We show that a plasma electromagnetic crystal attenuates a microwave propagation in the stopband more than by 4 orders of magnitude. In order to obtain an effective control of the transmission spectrum comparable with a metallic regular structure, the electron concentration in plasma inhomogeneities should vary within the range from 1014 cm-3 to 1016 cm-3, while gas temperature and mean electron energy must be in the range of 2000 K and 0.5 eV, respectively, to lower electron collision frequency around 1010 s-1. We analyze in detail the time evolution response of the electromagnetic crystal according to the plasma parameters for the duration of the discharge. The interest of using atmospheric pressure discharges is to increase the microwave breakdown threshold in discharge volumes, whereby it becomes possible to perform dynamic control of high power microwaves.

  16. Adhesion improvement of fibres by continuous plasma treatment at atmospheric pressure

    DEFF Research Database (Denmark)

    Kusano, Yukihiro; Løgstrup Andersen, Tom; Sørensen, Bent F.

    2013-01-01

    Carbon fibres and ultra-high-molecular-weight polyethylene (UHMWPE) fibres were continuously treated by a dielectric barrier discharge plasma at atmospheric pressure for adhesion improvement with epoxy resins. The plasma treatment improved wettability, increased the oxygen containing polar...

  17. Improved mapping of National Atmospheric Deposition Program wet-deposition in complex terrain using PRISM-gridded data sets.

    Science.gov (United States)

    Latysh, Natalie E; Wetherbee, Gregory Alan

    2012-01-01

    High-elevation regions in the United States lack detailed atmospheric wet-deposition data. The National Atmospheric Deposition Program/National Trends Network (NADP/NTN) measures and reports precipitation amounts and chemical constituent concentration and deposition data for the United States on annual isopleth maps using inverse distance weighted (IDW) interpolation methods. This interpolation for unsampled areas does not account for topographic influences. Therefore, NADP/NTN isopleth maps lack detail and potentially underestimate wet deposition in high-elevation regions. The NADP/NTN wet-deposition maps may be improved using precipitation grids generated by other networks. The Parameter-elevation Regressions on Independent Slopes Model (PRISM) produces digital grids of precipitation estimates from many precipitation-monitoring networks and incorporates influences of topographical and geographical features. Because NADP/NTN ion concentrations do not vary with elevation as much as precipitation depths, PRISM is used with unadjusted NADP/NTN data in this paper to calculate ion wet deposition in complex terrain to yield more accurate and detailed isopleth deposition maps in complex terrain. PRISM precipitation estimates generally exceed NADP/NTN precipitation estimates for coastal and mountainous regions in the western United States. NADP/NTN precipitation estimates generally exceed PRISM precipitation estimates for leeward mountainous regions in Washington, Oregon, and Nevada, where abrupt changes in precipitation depths induced by topography are not depicted by IDW interpolation. PRISM-based deposition estimates for nitrate can exceed NADP/NTN estimates by more than 100% for mountainous regions in the western United States.

  18. Improved mapping of National Atmospheric Deposition Program wet-deposition in complex terrain using PRISM-gridded data sets

    Science.gov (United States)

    Latysh, Natalie E.; Wetherbee, Gregory Alan

    2012-01-01

    High-elevation regions in the United States lack detailed atmospheric wet-deposition data. The National Atmospheric Deposition Program/National Trends Network (NADP/NTN) measures and reports precipitation amounts and chemical constituent concentration and deposition data for the United States on annual isopleth maps using inverse distance weighted (IDW) interpolation methods. This interpolation for unsampled areas does not account for topographic influences. Therefore, NADP/NTN isopleth maps lack detail and potentially underestimate wet deposition in high-elevation regions. The NADP/NTN wet-deposition maps may be improved using precipitation grids generated by other networks. The Parameter-elevation Regressions on Independent Slopes Model (PRISM) produces digital grids of precipitation estimates from many precipitation-monitoring networks and incorporates influences of topographical and geographical features. Because NADP/NTN ion concentrations do not vary with elevation as much as precipitation depths, PRISM is used with unadjusted NADP/NTN data in this paper to calculate ion wet deposition in complex terrain to yield more accurate and detailed isopleth deposition maps in complex terrain. PRISM precipitation estimates generally exceed NADP/NTN precipitation estimates for coastal and mountainous regions in the western United States. NADP/NTN precipitation estimates generally exceed PRISM precipitation estimates for leeward mountainous regions in Washington, Oregon, and Nevada, where abrupt changes in precipitation depths induced by topography are not depicted by IDW interpolation. PRISM-based deposition estimates for nitrate can exceed NADP/NTN estimates by more than 100% for mountainous regions in the western United States.

  19. Comparison of W–TiC composite coatings fabricated by atmospheric plasma spraying and supersonic atmospheric plasma spraying

    Energy Technology Data Exchange (ETDEWEB)

    Hou, Qing Yu, E-mail: qingyuhou@hotmail.com [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Anhui Key Laboratory of Metal Materials and Processing, Maanshan, Anhui 243002 (China); Luo, Lai Ma [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China); Huang, Zhen Yi; Wang, Ping; Ding, Ting Ting [Anhui Key Laboratory of Metal Materials and Processing, Maanshan, Anhui 243002 (China); Wu, Yu Cheng, E-mail: ycwu@hfut.edu.cn [School of Material Science and Engineering, Hefei University of Technology, Hefei, Anhui 230009 (China)

    2016-04-15

    Highlights: • W–TiC composite coatings were fabricated by APS and SAPS technologies. • TiC had filling effect on pores and coating/fixing effect on un-melted particles. • Porosity and oxygen content in SAPS coating were lower than that in APS coating. • Thermal conductivity of SAPS coating was higher than that of APS coating. • SAPS coating has better ability to resist to elastic fracture than APS coating does. - Abstract: Tungsten coatings with 1.5 wt.% TiC (W/TiC) were fabricated by atmospheric plasma spraying (APS) and supersonic atmospheric plasma spraying (SAPS) techniques, respectively. The results showed that the typical lamellar structure of plasma spraying and columnar crystalline grains formed in the coatings. Pores located mainly at lamellar gaps in association with oxidation were also observed. TiC phase, distributed at lamellar gaps filled the gaps; and that distributed around un-melted tungsten particles and splashed debris coated the particles or debris that were linked with the TiC at lamellar gaps. The coating and linking of the retained TiC phase prevented the tungsten particles to come off from the coatings. The porosity and the oxygen content of the SAPS-W/TiC were lower than those of the APS-W/TiC coating. The mechanical response of the coatings was strongly dependent on the H/E* ratio (H and E* are the hardness and effective Young’s modulus, respectively). The SAPS-W/TiC coating with a higher H/E* ratio had a better ability to resist to elastic fracture and better fracture toughness as compared with the APS-W/TiC coating with a smaller H/E* ratio. The thermal conductivity of the SAPS-W/TiC coating was greater than that of the APS-W/TiC coating.

  20. Deposition of titanium nitride and hydroxyapatite-based biocompatible composite by reactive plasma spraying

    Science.gov (United States)

    Roşu, Radu Alexandru; Şerban, Viorel-Aurel; Bucur, Alexandra Ioana; Dragoş, Uţu

    2012-02-01

    Titanium nitride is a bioceramic material successfully used for covering medical implants due to the high hardness meaning good wear resistance. Hydroxyapatite is a bioactive ceramic that contributes to the restoration of bone tissue, which together with titanium nitride may contribute to obtaining a superior composite in terms of mechanical and bone tissue interaction matters. The paper presents the experimental results in obtaining composite layers of titanium nitride and hydroxyapatite by reactive plasma spraying in ambient atmosphere. X-ray diffraction analysis shows that in both cases of powders mixtures used (10% HA + 90% Ti; 25% HA + 75% Ti), hydroxyapatite decomposition occurred; in variant 1 the decomposition is higher compared with the second variant. Microstructure of the deposited layers was investigated using scanning electron microscope, the surfaces presenting a lamellar morphology without defects such as cracks or microcracks. Surface roughness values obtained vary as function of the spraying distance, presenting higher values at lower thermal spraying distances.

  1. Impact of atmospheric nitrogen deposition on phytoplankton productivity in the South China Sea

    Science.gov (United States)

    Kim, Tae-Wook; Lee, Kitack; Duce, Robert; Liss, Peter

    2014-05-01

    The impacts of anthropogenic nitrogen (N) deposition on the marine N cycle are only now being revealed, but the magnitudes of those impacts are largely unknown in time and space. The South China Sea (SCS) is particularly subject to high anthropogenic N deposition, because the adjacent countries are highly populated and have rapidly growing economies. Analysis of data sets for atmospheric N deposition, satellite chlorophyll-a (Chl-a), and air mass back trajectories reveals that the transport of N originating from the populated east coasts of China and Indonesia, and its deposition to the ocean, has been responsible for the enhancements of Chl-a in the SCS. We found that atmospheric N deposition contributed approximately 20% of the annual biological new production in the SCS. The airborne contribution of N to new production in the SCS is expected to grow considerably in the coming decades.

  2. Atmospheric inorganic nitrogen deposition to a typical red soil forestland in southeastern China.

    Science.gov (United States)

    Fan, Jian-Ling; Hu, Zheng-Yi; Wang, Ti-Jian; Zhou, Jing; Wu, Cong-Yang-Hui; Xia, Xu

    2009-12-01

    A 2-year monitoring study was conducted to estimate nitrogen deposition to a typical red soil forestland in southeastern China. The dry deposition velocities (V(d)) were estimated using big leaf resistance analogy model. Atmospheric nitrogen dry deposition was estimated by combing V(d) and nitrogen compounds concentrations, and the wet deposition was calculated via rainfall and nitrogen concentrations in rainwater. The total inorganic nitrogen deposition was 83.7 kg ha(-1) a(-1) in 2004 and 81.3 kg ha(-1) a(-1) in 2005, respectively. The dry deposition contributed 78.6% to total nitrogen deposition, in which ammonia was the predominant contributor that accounted for 86.1%. Reduced nitrogen compounds were the predominant contributors, accounting for 78.3% of total nitrogen deposition. The results suggested that atmospheric inorganic nitrogen could be attributed to intensive agricultural practices such as excessive nitrogen fertilization and livestock production. Therefore, impacts of atmospheric nitrogen originated from agriculture practices on nearby forest ecosystems should be evaluated.

  3. Properties of HfAlO film deposited by plasma enhanced atomic layer deposition

    Energy Technology Data Exchange (ETDEWEB)

    Cao, Duo [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Chinese Academy of Sciences, Changning Road 865, Shanghai 200050 (China); Cheng, Xinhong, E-mail: xh_cheng@mail.sim.ac.cn [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Chinese Academy of Sciences, Changning Road 865, Shanghai 200050 (China); Jia, Tingting; Zheng, Li; Xu, Dawei; Wang, Zhongjian; Xia, Chao; Yu, Yuehui [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Chinese Academy of Sciences, Changning Road 865, Shanghai 200050 (China)

    2013-07-15

    Plasma enhanced atomic layer deposition (PEALD) method can reduce film growing temperature, and allow in situ plasma treatment. In this work, HfAlO and HfO{sub 2} films were deposited with PEALD at 160 °C. Microstructure analysis showed that both films were amorphous after rapid thermal annealing (RTA) treatment, and HfAlO sample showed better interfacial structure than HfO{sub 2}. X-ray photoelectron spectroscopy (XPS) spectra indicated that main component of the interfacial layer of HfAlO sample was Hf–Si–O and Al–Si–O bonds, the valence band offset value between the HfAlO film and Si substrate was calculated to be 2.5 eV. The dominant leakage current mechanism of the samples was Schottky emission at a low electric field (<1.4 MV/cm), and Poole–Frenkel emission mechanism at a higher electric field (>1.4 MV/cm). The equivalent oxide thicknesses (EOT) of the HfAlO samples were 1.0 nm and 1.3 nm, respectively. The density of interface states between dielectric and substrate were calculated to be 1.2 × 10{sup 12} eV{sup −1}cm{sup −2} and 1.3 × 10{sup 12} eV{sup −1}cm{sup −2}, respectively. In comparison with HfO{sub 2} film, HfAlO film has good interfacial structure and electrical performance.

  4. Numerical simulation of chemical processes in helium plasmas in atmosphere environment

    Institute of Scientific and Technical Information of China (English)

    欧阳建明; 郭伟; 王龙; 邵福球

    2005-01-01

    A model is built to study chemical processes in plasmas generated in helium with trace amounts of air at atmospheric pressure or low pressures. The plasma lifetimes and the temporal evolutions of the main charged species are presented. The plasma lifetimes are longer than that in air plasma at atmospheric pressure, but this is not true at low pressures. The electron number density does not strictly obey the exponential damping law in a longer period.

  5. Is Recovery of Forest Soils from Acidic Deposition Accelerating Watershed Release of Atmospherically Deposited Nitrogen Accumulated over Past Decades?

    Science.gov (United States)

    Lawrence, G. B.; Sabo, R.; Scanga, S. E.; Momen, B.

    2016-12-01

    The trend of decreasing atmospheric N deposition in the northeastern U.S. has accelerated since 2000, leading to the possibility that surface water concentrations of NO3 and its acidifying effects would also decrease. Decreases of NO3 in lakes have been observed in regions such as the Adirondacks of NY, but these decreases were linked to increased productivity within the lakes. Less information is available on changes in NO3 concentrations in streams and watershed export of N. In a previous analysis, monitoring from 2000-2012 of the North and South Tributary watersheds of Buck Creek, in the western Adirondack region, showed no trends in annual watershed NO3 export, despite a decline in atmospheric N deposition. Surveys of 64 Adirondack streams also showed no overall change in NO3 concentrations between 2004 and 2014. Following on these studies, controls of N retention in the Buck Creek watersheds were investigated with data on tree growth, soil chemistry, stream flow, and stream chemistry. Tree measurements showed little change in basal area from 2000-2015 in the North Watershed (+ 0.8 percent) and an increase (+16 percent) in the South Watershed; results inconsistent with decreased N retention by vegetation. However, large decreases in Al and stable or increasing Ca were measured in O horizons of these watersheds (1997- 2009/10, North; 1998-2014, South), as the soils responded to long-term decreases in acidic deposition. Past increases in Al and decreases in Ca from acidic deposition have been linked to slowed decomposition rates. The lower Al concentrations and higher Ca availability measured at Buck Creek may have led to increased decomposition rates, providing an explanation for the sustained watershed export of N since 2000. These results suggest a possible legacy effect of atmospheric N deposition that is reversing as these ecosystems recover from acidic deposition.

  6. Use of Atmospheric Pressure Cold Plasma for Meat Industry.

    Science.gov (United States)

    Lee, Juri; Lee, Cheol Woo; Yong, Hae In; Lee, Hyun Jung; Jo, Cheorun; Jung, Samooel

    2017-01-01

    Novel, effective methods to control and prevent spoilage and contamination by pathogenic microorganisms in meat and meat products are in constant demand. Non-thermal pasteurization is an ideal method for the preservation of meat and meat products because it does not use heat during the pasteurization process. Atmospheric pressure cold plasma (APCP) is a new technology for the non-thermal pasteurization of meat and meat products. Several recent studies have shown that APCP treatment reduces the number of pathogenic microorganisms in meat and meat products. Furthermore, APCP treatment can be used to generate nitrite, which is an essential component of the curing process. Here, we introduce the effectiveness of APCP treatment as a pasteurization method and/or curing process for use in the meat and meat product processing industry.

  7. Modification of Composite Material Fillers by Atmospheric Plasma Discharge

    Directory of Open Access Journals (Sweden)

    David Tichy

    2013-01-01

    Full Text Available This work is focused on the observation of the influence of cold atmospheric dielectric barrier discharge (DBD on a modification of textile samples. The main objective of the experiment is to research wettability change of textiles modified by different exposure times and also the observation of the influence of a modification ageing effect. An ambient air was used as a working gas for DBD plasma. The wettability evaluation was carried out by a drop method, in which an imprint of the dropwas observed on the textile surface during various time intervals. An ageing effect of the modification was monitored within an interval of 28 days. Considerable increase of wettability of all modified samples has been proved. A fibre surface analysis was carried out by means of SEM.

  8. Surface Treatment of PET Nonwovens with Atmospheric Plasma

    Science.gov (United States)

    Li, Shufang

    2013-01-01

    In this study, polyethylene-terephthalate (PET) nonwovens are treated using an atmospheric plasma and the effects of the treatment time, treatment power and discharge distance on the ability of water-penetration into the nonwovens are investigated. The result indicates that the method can improve the wettability of PET nonwovens remarkably, but the aging decay of the sample's wettability is found to be notable as a function of the storage time after treatment due to the internal rotation of the single bond of surface macromolecules. As shown by SEM and XPS analysis, the etching and surface reaction are significant, and water-penetration weight is found to increase remarkably with the increasing power. This variation can be attributed to momentum transfer and enhanced higher-energy particle excitation.

  9. Ultrafast laser-collision-induced fluorescence in atmospheric pressure plasma

    Science.gov (United States)

    Barnat, E. V.; Fierro, A.

    2017-04-01

    The implementation and demonstration of laser-collision-induced fluorescence (LCIF) generated in atmospheric pressure helium environments is presented in this communication. As collision times are observed to be fast (~10 ns), ultrashort pulse laser excitation (<100 fs) of the 23S to 33P (388.9 nm) is utilized to initiate the LCIF process. Both neutral-induced and electron-induced components of the LCIF are observed in the helium afterglow plasma as the reduced electric field (E/N) is tuned from  <0.1 Td to over 5 Td. Under the discharge conditions presented in this study (640 Torr He), the lower limit of electron density detection is ~1012 e cm‑3. The spatial profiles of the 23S helium metastable and electrons are presented as functions of E/N to demonstrate the spatial resolving capabilities of the LCIF method.

  10. Electrochromic Devices Deposited on Low-Temperature Plastics by Plasma-Enhanced Chemical Vapor Deposition

    Energy Technology Data Exchange (ETDEWEB)

    Robbins, Joshua; Seman, Michael

    2005-09-20

    Electrochromic windows have been identified by the Basic energy Sciences Advisory committee as an important technology for the reduction of energy spent on heating and cooling in residential and commercial buildings. Electrochromic devices have the ability to reversibly alter their optical properties in response to a small electric field. By blocking ultraviolet and infrared radiation, while modulating the incoming visible radiation, electrochromics could reduce energy consumption by several Quads per year. This amounts to several percent of the total annual national energy expenditures. The purpose of this project was to demonstrate proof of concept for using plasma-enhanced chemical vapor deposition (PECVD) for depositing all five layers necessary for full electrochromic devices, as an alternative to sputtering techniques. The overall goal is to produce electrochromic devices on flexible polymer substrates using PECVD to significantly reduce the cost of the final product. We have successfully deposited all of the films necessary for a complete electrochromic devices using PECVD. The electrochromic layer, WO3, displayed excellent change in visible transmission with good switching times. The storage layer, V2O5, exhibited a high storage capacity and good clear state transmission. The electrolyte, Ta2O5, was shown to functional with good electrical resistivity to go along with the ability to transfer Li ions. There were issues with leakage over larger areas, which can be address with further process development. We developed a process to deposit ZnO:Ga with a sheet resistance of < 50 W/sq. with > 90% transmission. Although we were not able to deposit on polymers due to the temperatures required in combination with the inverted position of our substrates. Two types of full devices were produced. Devices with Ta2O5 were shown to be functional using small aluminum dots as the top contact. The polymer electrolyte devices were shown to have a clear state transmission of

  11. Characterization of Carbon Deposits Formed During Plasma Pyrolysis of Xinjiang Candle Coal

    Science.gov (United States)

    Zhu, Guilin; Meng, Yuedong; Shu, Xingsheng; Fang, Shidong

    2009-08-01

    Carbon deposits were formed on the reactor wall during plasma pyrolysis of the Xinjiang candle coal in our V-style plasma pyrolysis pilot-plant. The carbon deposits were studied using a scanning electronic microscope (SEM) and the X-ray diffraction (XRD) method. It was found that carbon deposits located at different parts in the reactor exhibited different microscopic patterns. The formation mechanism of the carbon deposits was deduced. The downward increase in the graphitization degree of the carbon deposits was found and interpreted.

  12. Characterization of carbon deposits formed during plasma pyrolysis of Xinjiang candle coal

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, G.L.; Meng, Y.D.; Shu, X.S.; Fang, S.D. [Chinese Academy of Sciences, Hefei (China). Inst. of Plasma Physics

    2009-08-15

    Carbon deposits were formed on the reactor wall during plasma pyrolysis of the Xinjiang candle coal in our V-style plasma pyrolysis pilot-plant. The carbon deposits were studied using a scanning electronic microscope (SEM) and the X-ray diffraction (XRD) method. It was found that carbon deposits located at different parts in the reactor exhibited different microscopic patterns. The formation mechanism of the carbon deposits was deduced. The down ward increase in the graphitization degree of the carbon deposits was found and interpreted

  13. Wet and dry atmospheric depositions of inorganic nitrogen during plant growing season in the coastal zone of Yellow River Delta.

    Science.gov (United States)

    Yu, Junbao; Ning, Kai; Li, Yunzhao; Du, Siyao; Han, Guangxuan; Xing, Qinghui; Wu, Huifeng; Wang, Guangmei; Gao, Yongjun

    2014-01-01

    The ecological problems caused by dry and wet deposition of atmospheric nitrogen have been widespread concern in the world. In this study, wet and dry atmospheric depositions were monitored in plant growing season in the coastal zone of the Yellow River Delta (YRD) using automatic sampling equipment. The results showed that SO4 (2-) and Na(+) were the predominant anion and cation, respectively, in both wet and dry atmospheric depositions. The total atmospheric nitrogen deposition was ~2264.24 mg m(-2), in which dry atmospheric nitrogen deposition was about 32.02%. The highest values of dry and wet atmospheric nitrogen deposition appeared in May and August, respectively. In the studied area, NO3 (-)-N was the main nitrogen form in dry deposition, while the predominant nitrogen in wet atmospheric deposition was NH4 (+)-N with ~56.51% of total wet atmospheric nitrogen deposition. The average monthly attribution rate of atmospheric deposition of NO3 (-)-N and NH4 (+)-N was ~31.38% and ~20.50% for the contents of NO3 (-)-N and NH4 (+)-N in 0-10 cm soil layer, respectively, suggested that the atmospheric nitrogen was one of main sources for soil nitrogen in coastal zone of the YRD.

  14. Effect of plasma parameters on characteristics of silicon nitride film deposited by single and dual frequency plasma enhanced chemical vapor deposition

    Science.gov (United States)

    Sahu, B. B.; Yin, Yongyi; Han, Jeon G.

    2016-03-01

    This work investigates the deposition of hydrogenated amorphous silicon nitride films using various low-temperature plasmas. Utilizing radio-frequency (RF, 13.56 MHz) and ultra-high frequency (UHF, 320 MHz) powers, different plasma enhanced chemical vapor deposition processes are conducted in the mixture of reactive N2/NH3/SiH4 gases. The processes are extensively characterized using different plasma diagnostic tools to study their plasma and radical generation capabilities. A typical transition of the electron energy distribution function from single- to bi-Maxwellian type is achieved by combining RF and ultra-high powers. Data analysis revealed that the RF/UHF dual frequency power enhances the plasma surface heating and produces hot electron population with relatively low electron temperature and high plasma density. Using various film analysis methods, we have investigated the role of plasma parameters on the compositional, structural, and optical properties of the deposited films to optimize the process conditions. The presented results show that the dual frequency power is effective for enhancing dissociation and ionization of neutrals, which in turn helps in enabling high deposition rate and improving film properties.

  15. Effective dose delivery in atmospheric pressure plasma jets for plasma medicine: a model predictive control approach

    Science.gov (United States)

    Gidon, Dogan; Graves, David B.; Mesbah, Ali

    2017-08-01

    Atmospheric pressure plasma jets (APPJs) have been identified as a promising tool for plasma medicine. This paper aims to demonstrate the importance of using model-based feedback control strategies for safe, reproducible, and therapeutically effective application of APPJs for dose delivery to a target substrate. Key challenges in model-based control of APPJs arise from: (i) the multivariable, nonlinear nature of system dynamics, (ii) the need for constraining the system operation within an operating region that ensures safe plasma treatment, and (iii) the cumulative, nondecreasing nature of dose metrics. To systematically address these challenges, we propose a model predictive control (MPC) strategy for real-time feedback control of a radio-frequency APPJ in argon. To this end, a lumped-parameter, physics-based model is developed for describing the jet dynamics. Cumulative dose metrics are defined for quantifying the thermal and nonthermal energy effects of the plasma on substrate. The closed-loop performance of the MPC strategy is compared to that of a basic proportional-integral control system. Simulation results indicate that the MPC stategy provides a versatile framework for dose delivery in the presence of disturbances, while the safety and practical constraints of the APPJ operation can be systematically handled. Model-based feedback control strategies can lead to unprecedented opportunities for effective dose delivery in plasma medicine.

  16. Plasma penetration depth and mechanical properties of atmospheric plasma-treated 3D aramid woven composites

    Energy Technology Data Exchange (ETDEWEB)

    Chen, X.; Yao, L.; Xue, J.; Zhao, D.; Lan, Y.; Qian, X. [Key Laboratory of Textile Science and Technology, Donghua University, Ministry of Education (China); Department of Textile Materials Science and Product Design, College of Textiles, Donghua University, Shanghai 201620 (China); Wang, C.X. [Key Laboratory of Textile Science and Technology, Donghua University, Ministry of Education (China); Department of Textile Materials Science and Product Design, College of Textiles, Donghua University, Shanghai 201620 (China); College of Textiles and Clothing, Yancheng Institute of Technology, Jiangsu 224003 (China); Qiu, Y. [Key Laboratory of Textile Science and Technology, Donghua University, Ministry of Education (China); Department of Textile Materials Science and Product Design, College of Textiles, Donghua University, Shanghai 201620 (China)], E-mail: ypqiu@dhu.edu.cn

    2008-12-30

    Three-dimensional aramid woven fabrics were treated with atmospheric pressure plasmas, on one side or both sides to determine the plasma penetration depth in the 3D fabrics and the influences on final composite mechanical properties. The properties of the fibers from different layers of the single side treated fabrics, including surface morphology, chemical composition, wettability and adhesion properties were investigated using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), contact angle measurement and microbond tests. Meanwhile, flexural properties of the composites reinforced with the fabrics untreated and treated on both sides were compared using three-point bending tests. The results showed that the fibers from the outer most surface layer of the fabric had a significant improvement in their surface roughness, chemical bonding, wettability and adhesion properties after plasma treatment; the treatment effect gradually diminished for the fibers in the inner layers. In the third layer, the fiber properties remained approximately the same to those of the control. In addition, three-point bending tests indicated that the 3D aramid composite had an increase of 11% in flexural strength and 12% in flexural modulus after the plasma treatment. These results indicate that composite mechanical properties can be improved by the direct fabric treatment instead of fiber treatment with plasmas if the fabric is less than four layers thick.

  17. Evaluating the Contributions of Atmospheric Deposition of Carbon and Other Nutrients to Nitrification in Alpine Environments

    Science.gov (United States)

    Oldani, K. M.; Mladenov, N.; Williams, M. W.

    2013-12-01

    The Colorado Front Range of the Rocky Mountains contains undeveloped, barren soils, yet in this environment there is strong evidence for a microbial role in increased nitrogen (N) export. Barren soils in alpine environments are severely carbon-limited, which is the main energy source for microbial activity and sustenance of life. It has been shown that atmospheric deposition can contain high amounts of organic carbon (C). Atmospheric pollutants, dust events, and biological aerosols, such as bacteria, may be important contributors to the atmospheric organic C load. In this stage of the research we evaluated seasonal trends in the chemical composition and optical spectroscopic (fluorescence and UV-vis absorbance) signatures of snow, wet deposition, and dry deposition in an alpine environment at Niwot Ridge in the Rocky Mountains of Colorado to obtain a better understanding of the sources and chemical character of atmospheric deposition. Our results reveal a positive trend between dissolved organic carbon concentrations and calcium, nitrate and sulfate concentrations in wet and dry deposition, which may be derived from such sources as dust and urban air pollution. We also observed the presence of seasonally-variable fluorescent components that may be attributed to fluorescent pigments in bacteria. These results are relevant because atmospheric inputs of carbon and other nutrients may influence nitrification in barren, alpine soils and, ultimately, the export of nitrate to alpine watersheds.

  18. Cold Atmospheric Plasma: methods of production and application in dentistry and oncology.

    Science.gov (United States)

    Hoffmann, Clotilde; Berganza, Carlos; Zhang, John

    2013-01-01

    Cold Atmospheric Plasma is an ionized gas that has recently been extensively studied by researchers as a possible therapy in dentistry and oncology. Several different gases can be used to produce Cold Atmospheric Plasma such as Helium, Argon, Nitrogen, Heliox, and air. There are many methods of production by which cold atmospheric plasma is created. Each unique method can be used in different biomedical areas. In dentistry, researchers have mostly investigated the antimicrobial effects produced by plasma as a means to remove dental biofilms and eradicate oral pathogens. It has been shown that reactive oxidative species, charged particles, and UV photons play the main role. Cold Atmospheric Plasma has also found a minor, but important role in tooth whitening and composite restoration. Furthermore, it has been demonstrated that Cold Atmospheric Plasma induces apoptosis, necrosis, cell detachment, and senescence by disrupting the S phase of cell replication in tumor cells. This unique finding opens up its potential therapy in oncology.

  19. Atmospheric Pressure Plasma Jet for Chem/Bio Warfare Decontamination

    Science.gov (United States)

    Herrmann, Hans W.; Henins, Ivars; Park, Jaeyoung; Selwyn, Gary S.

    1999-11-01

    Atmospheric Pressure Plasma Jet (APPJ) technology may provide a much needed method of CBW decontamination which, unlike traditional decon methods, is dry and nondestructive to sensitive equipment and materials. The APPJ discharge uses a high-flow feedgas consisting primarily of an inert carrier gas, such as He, and a small amount of a reactive additive, such as O2, which flows between capacitively-coupled electrodes powered at 13.56 MHz. The plasma generates highly reactive metastable and atomic species of oxygen which are then directed onto a contaminated surface. The reactive effluent of the APPJ has been shown to effectively neutralize VX nerve agent as well as simulants for anthrax and mustard blister agent. Research efforts are now being directed towards reducing He consumption and increasing the allowable stand-off distance. Recent results demonstrate that by replacing the O2 reactive additive with CO2, ozone formation is greatly reduced. This has the result of extending the lifetime of atomic oxygen by an order of magnitude or more. A recirculating APP Decon Chamber which combines heat, vacuum, forced convection and reactivity is currently being developed for enhanced decontamination of sensitive equipment. Several techniques are also being evaluated for use in an APP Decon Jet for decontamination of items which cannot be placed inside a chamber.

  20. Cold atmospheric plasma for selectively ablating metastatic breast cancer cells.

    Science.gov (United States)

    Wang, Mian; Holmes, Benjamin; Cheng, Xiaoqian; Zhu, Wei; Keidar, Michael; Zhang, Lijie Grace

    2013-01-01

    Traditional breast cancer treatments such as surgery and radiotherapy contain many inherent limitations with regards to incomplete and nonselective tumor ablation. Cold atmospheric plasma (CAP) is an ionized gas where the ion temperature is close to room temperature. It contains electrons, charged particles, radicals, various excited molecules, UV photons and transient electric fields. These various compositional elements have the potential to either enhance and promote cellular activity, or disrupt and destroy them. In particular, based on this unique composition, CAP could offer a minimally-invasive surgical approach allowing for specific cancer cell or tumor tissue removal without influencing healthy cells. Thus, the objective of this research is to investigate a novel CAP-based therapy for selectively bone metastatic breast cancer treatment. For this purpose, human metastatic breast cancer (BrCa) cells and bone marrow derived human mesenchymal stem cells (MSCs) were separately treated with CAP, and behavioral changes were evaluated after 1, 3, and 5 days of culture. With different treatment times, different BrCa and MSC cell responses were observed. Our results showed that BrCa cells were more sensitive to these CAP treatments than MSCs under plasma dose conditions tested. It demonstrated that CAP can selectively ablate metastatic BrCa cells in vitro without damaging healthy MSCs at the metastatic bone site. In addition, our study showed that CAP treatment can significantly inhibit the migration and invasion of BrCa cells. The results suggest the great potential of CAP for breast cancer therapy.

  1. Cold atmospheric plasma for selectively ablating metastatic breast cancer cells.

    Directory of Open Access Journals (Sweden)

    Mian Wang

    Full Text Available Traditional breast cancer treatments such as surgery and radiotherapy contain many inherent limitations with regards to incomplete and nonselective tumor ablation. Cold atmospheric plasma (CAP is an ionized gas where the ion temperature is close to room temperature. It contains electrons, charged particles, radicals, various excited molecules, UV photons and transient electric fields. These various compositional elements have the potential to either enhance and promote cellular activity, or disrupt and destroy them. In particular, based on this unique composition, CAP could offer a minimally-invasive surgical approach allowing for specific cancer cell or tumor tissue removal without influencing healthy cells. Thus, the objective of this research is to investigate a novel CAP-based therapy for selectively bone metastatic breast cancer treatment. For this purpose, human metastatic breast cancer (BrCa cells and bone marrow derived human mesenchymal stem cells (MSCs were separately treated with CAP, and behavioral changes were evaluated after 1, 3, and 5 days of culture. With different treatment times, different BrCa and MSC cell responses were observed. Our results showed that BrCa cells were more sensitive to these CAP treatments than MSCs under plasma dose conditions tested. It demonstrated that CAP can selectively ablate metastatic BrCa cells in vitro without damaging healthy MSCs at the metastatic bone site. In addition, our study showed that CAP treatment can significantly inhibit the migration and invasion of BrCa cells. The results suggest the great potential of CAP for breast cancer therapy.

  2. Cold atmospheric plasma jet in an axial DC electric field

    Science.gov (United States)

    Lin, Li; Keidar, Michael

    2016-08-01

    Cold atmospheric plasma (CAP) jet is currently intensively investigated as a tool for new and potentially transformative cancer treatment modality. However, there are still many unknowns about the jet behavior that requires attention. In this paper, a helium CAP jet is tested in an electrostatic field generated by a copper ring. Using Rayleigh microwave scattering method, some delays of the electron density peaks for different ring potentials are observed. Meanwhile, a similar phenomenon associated with the bullet velocity is found. Chemical species distribution along the jet is analyzed based on the jet optical emission spectra. The spectra indicate that a lower ring potential, i.e., lower DC background electric field, can increase the amount of excited N2, N2+, He, and O in the region before the ring, but can decrease the amount of excited NO and HO almost along the entire jet. Combining all the results above, we discovered that an extra DC potential mainly affects the temporal plasma jet properties. Also, it is possible to manipulate the chemical compositions of the jet using a ring with certain electric potentials.

  3. Basic characteristics of an atmospheric pressure rf generated plasma jet

    Institute of Scientific and Technical Information of China (English)

    Wang Shou-Guo; Li Hai-Jiang; Ye Tian-Chun; Zhao Ling-Li

    2004-01-01

    A plasma jet has been developed which operates using radio frequency (rf) power and produces a stable homogeneous discharge at atmospheric pressure. Its discharge characteristics, especially the dependence of stable discharge operating range on the feed gas, were studied, and the electric parameters such as RMS current, RMS voltage and reflected power were obtained with different gas flows. These studies indicate that there is an optimum range of operation of the plasma jet for a filling with a gas mixture of He and O2. Two "failure" modes of the discharge are identified.One is a filamentary arc when the input power is raised above a critical level, another is that the discharge disappears gradually as the addition of O2 approaches 3.2%. Possible explanations for the two failure modes have been given. The current and voltage waveform measurements show that there is a clear phase shift between normal and failure modes.In addition, Ⅰ-Ⅴ curves as a function of pure helium and for 1% addition of oxygen have been studied.

  4. RF atmospheric plasma jet surface treatment of paper

    Science.gov (United States)

    Pawlat, Joanna; Terebun, Piotr; Kwiatkowski, Michał; Diatczyk, Jaroslaw

    2016-09-01

    A radio frequency RF atmospheric pressure plasma jet was used to enhance the wettability of cellulose-based paper of 90 g m-2 and 160 g m-2 grammage as a perspective platform for antibiotic sensitivity tests. Helium and argon were the carrier gases for oxygen and nitrogen; pure water and rapeseed oil were used for goniometric tests. The influence of the flow rate and gas type, the power of the discharge, and distance from the nozzle was examined. The surface structure was observed using an optical microscope. Attenuated total reflection Fourier transform infrared (ATR-FTIR) spectra were investigated in order to determine whether cellulose degradation processes occurred. The RF plasma jet allowed us to decrease the surface contact angle without drastic changes in other features of the tested material. Experiments confirmed the significant influence of the distance between the treated sample and reactor nozzle, especially for treatment times longer than 15 s due to the greater concentration of reactive species at the surface of the sample, which decreases with distance—and their accumulation effect with time. The increase of discharge power plays an important role in decreasing the surface contact angle for times longer than 10 s. Higher power had a positive effect on the amount of generated active particles and facilitated the ignition of discharge. However, a too high value can cause a rise in temperature of the material and heat-caused damage.

  5. Natural or anthropogenic? On the origin of atmospheric sulfate deposition in the Andes of southeastern Ecuador

    Directory of Open Access Journals (Sweden)

    S. Makowski Giannoni

    2014-05-01

    Full Text Available Atmospheric sulfur deposition above certain limits can represent a threat to tropical forests, causing nutrient imbalances and mobilizing toxic elements that impact biodiversity and forest productivity. Atmospheric sources of sulfur deposited by precipitation have being roughly identified in only a few lowland tropical forests. Even scarcer are these type of studies in tropical mountain forests, many of them megadiversity hotspots and especially vulnerable to acidic deposition. Here, the topographic complexity and related streamflow condition the origin, type, and intensity of deposition. Furthermore, in regions with a variety of natural and anthropogenic sulfur sources, like active volcanoes and biomass-burning, no source-emission data has been used for determining the contribution of each of them to the deposition. The main goal of the current study is to evaluate sulfate (SO4− deposition by rain and occult precipitation at two topographic locations in a tropical mountain forest of southern Ecuador, and to trace back the deposition to possible emission sources applying back trajectory modeling. To link upwind natural (volcanic and anthropogenic (urban/industrial and biomass-burning sulfur emissions and observed sulfate deposition, we employed state of the art inventory and satellite data, including volcanic passive degassing as well. We conclude that biomass-burning sources generally dominate sulfate deposition at the evaluated sites. Minor sulfate transport occurs during the shifting of the predominant winds to the north and west. Occult precipitation sulfate deposition and likely rain sulfate deposition are mainly linked to biomass-burning emissions from the Amazon lowlands. Volcanic and anthropogenic emissions from the north and west contribute to occult precipitation sulfate deposition at the mountain crest Cerro del Consuelo meteorological station and to rain-deposited sulfate at the upriver mountain-pass El Tiro meteorological station.

  6. Production of selective membranes using plasma deposited nanochanneled thin films

    Directory of Open Access Journals (Sweden)

    Rodrigo Amorim Motta Carvalho

    2006-12-01

    Full Text Available The hydrolization of thin films obtained by tetraethoxysilane plasma polymerization results in the formation of a nanochanneled silicone like structure that could be useful for the production of selective membranes. Therefore, the aim of this work is to test the permeation properties of hydrolyzed thin films. The films were tested for: 1 permeation of polar organic compounds and/or water in gaseous phase and 2 permeation of salt in liquid phase. The efficiency of permeation was tested using a quartz crystal microbalance (QCM technique in gas phase and conductimetric analysis (CA in liquid phase. The substrates used were: silicon for characterization of the deposited films, piezoelectric quartz crystals for tests of selective membranes and cellophane paper for tests of permeation. QCM analysis showed that the nanochannels allow the adsorption and/or permeation of polar organic compounds, such as acetone and 2-propanol, and water. CA showed that the films allow salt permeation after an inhibition time needed for hydrolysis of the organic radicals within the film. Due to their characteristics, the films can be used for grains protection against microorganism proliferation during storage without preventing germination.

  7. Isothermal Oxidation Behavior of Supersonic Atmospheric Plasma-Sprayed Thermal Barrier Coating System

    Science.gov (United States)

    Bai, Yu; Ding, Chunhua; Li, Hongqiang; Han, Zhihai; Ding, Bingjun; Wang, Tiejun; Yu, Lie

    2013-10-01

    In this work, Y2O3 stabilized zirconia-based thermal barrier coatings (TBCs) were deposited by conventional atmospheric plasma spraying (APS) and high efficiency supersonic atmospheric plasma spraying (SAPS), respectively. The effect of Al2O3 layer stability on the isothermal growth behavior of thermally grown oxides (TGOs) was studied. The results revealed that the Al2O3 layer experienced a three-stage change process, i.e., (1) instantaneous growth stage, (2) steady-state growth stage, and (3) depletion stage. The thickness of Al2O3 scale was proved to be an important factor for the growth rate of TGOs. The SAPS-TBCs exhibited a higher Al2O3 stability and better oxidation resistance as compared with the APS-TBCs. Additionally, it was found that inner oxides, especially nucleated on the top of the crest, continually grew and swallowed the previously formed Al2O3 layer, leading to the granulation and disappearance of continuous Al2O3 scale, which was finally replaced by the mixed oxides and spinel.

  8. Solar Flux Deposition And Heating Rates In Jupiter's Atmosphere

    Science.gov (United States)

    Perez-Hoyos, Santiago; Sánchez-Lavega, A.

    2009-09-01

    We discuss here the solar downward net flux in the 0.25 - 2.5 µm range in the atmosphere of Jupiter and the associated heating rates under a number of vertical cloud structure scenarios focusing in the effect of clouds and hazes. Our numerical model is based in the doubling-adding technique to solve the radiative transfer equation and it includes gas absorption by CH4, NH3 and H2, in addition to Rayleigh scattering by a mixture of H2 plus He. Four paradigmatic Jovian regions have been considered (hot-spots, belts, zones and Polar Regions). The hot-spots are the most transparent regions with downward net fluxes of 2.5±0.5 Wm-2 at the 6 bar level. The maximum solar heating is 0.04±0.01 K/day and occurs above 1 bar. Belts and zones characterization result in a maximum net downward flux of 0.5 Wm-2 at 2 bar and 0.015 Wm-2 at 6 bar. Heating is concentrated in the stratospheric and tropospheric hazes. Finally, Polar Regions are also explored and the results point to a considerable stratospheric heating of 0.04±0.02 K/day. In all, these calculations suggest that the role of the direct solar forcing in the Jovian atmospheric dynamics is limited to the upper 1 - 2 bar of the atmosphere except in the hot-spot areas. Acknowledgments: This work has been funded by Spanish MEC AYA2006-07735 with FEDER support and Grupos Gobierno Vasco IT-464-07.

  9. Tribological behavior of plasma-polymerized aminopropyltriethoxysilane films deposited on thermoplastic elastomers substrates

    Energy Technology Data Exchange (ETDEWEB)

    Alba-Elías, Fernando, E-mail: fernando.alba@unirioja.es [Department of Mechanical Engineering, University of La Rioja, c/Luis de Ulloa 20, 26004 Logroño, La Rioja (Spain); Sainz-García, Elisa; González-Marcos, Ana [Department of Mechanical Engineering, University of La Rioja, c/Luis de Ulloa 20, 26004 Logroño, La Rioja (Spain); Ordieres-Meré, Joaquín [ETSII, Polytechnic University of Madrid, c/José Gutiérrez Abascal 2, 28006 Madrid (Spain)

    2013-07-01

    Thermoplastic elastomers (TPE) are multifunctional polymeric materials that are characterized by moderate cost, excellent mechanical properties (high elasticity, good flexibility, hardness, etc.), high tensile strength, oxidation and wettability. With an objective of reducing the superficial friction coefficient of TPE, this work analyzes the characteristics of coating films that are based on aminopropyltriethoxysilane (APTES) over a TPE substrate. Since this material is heat-sensitive, it is necessary to use a technology that permits the deposition of coatings at low temperatures without affecting the substrate integrity. Thus, an atmospheric-pressure plasma jet system (APPJ) with a dielectric barrier discharge (DBD) was used in this study. The coated samples were analyzed by Scanning Electron Microscopy, Atomic Force Microscopy, Fourier-Transform Infrared with Attenuated Total Reflectance Spectroscopy, X-ray Photoelectron Spectroscopy and tribological tests (friction coefficient and wear rate). The studies showed that the coated samples that contain a higher amount of forms of silicon (SiOSi) and nitrogen (amines, amides and imines) have lower friction coefficients. The sample coated at a specific plasma power of 550 W and an APTES flow rate of 1.5 slm had the highest values of SiOSi and nitrogen-containing groups peak intensity and atomic percentages of Si2p and SiO{sub 4}, and the lowest percentages of C1s and average friction coefficient. The results of this research permit one to conclude that APPJ with a DBD is a promising technique to use in coating SiO{sub x} and nitrogen-containing groups layers on polymeric materials. - Highlights: • SiO{sub x} thin films on thermoplastic elastomers by atmospheric pressure plasma jet. • Study of influence of plasma power and precursor flow rate on film's properties. • Friction coefficient is inversely related to the amount of SiOSi and N groups. • Nitrogen groups from the ionization gas (N{sub 2}) seem to

  10. Infrared Absorption Spectroscopic Study on Reaction between Self-Assembled Monolayers and Atmospheric-Pressure Plasma

    Directory of Open Access Journals (Sweden)

    Masanori Shinohara

    2015-01-01

    Full Text Available Plasma is becoming increasingly adopted in bioapplications such as plasma medicine and agriculture. This study investigates the interaction between plasma and molecules in living tissues, focusing on plasma-protein interactions. To this end, the reaction of air-pressure air plasma with NH2-terminated self-assembled monolayer is investigated by infrared spectroscopy in multiple internal reflection geometry. The atmospheric-pressure plasma decomposed the NH2 components, the characteristic units of proteins. The decomposition is attributed to water clusters generated in the plasma, indicating that protein decomposition by plasma requires humid air.

  11. Modeling of atmospheric iron processing carried by mineral dust and its deposition to ocean

    Science.gov (United States)

    Nickovic, Slobodan; Vukovic, Ana; Vujadinovic, Mirjam

    2014-05-01

    Relatively insoluble iron in dust originating from desert soils increases its solubility after Fe carried by mineral dust is chemically processed by the atmosphere. After dust is deposited deposition to the ocean, soluble Fe as a nutrient could enhance the marine primary production. The atmospheric dust cycle is driven by the atmospheric processes often of smaller, meso-scales. The soil mineralogy of dust emitted from sources determines also how much Fe in the aerosol will be finding. Once Fe is exposed to the atmospheric processes, the atmospheric radiation, clouds and polluted air will chemically affect the iron in dust. Global dust-iron models, having typical horizontal resolutions of 100-300 km which are mostly used to numerically simulate the fate of iron in the atmosphere can provide rather global picture of the dust and iron transport, but not details. Such models often introduce simplistic approximation on the Fe content in dust-productive soils. To simulate the Fe processing we instead implemented a high resolution regional atmospheric dust-iron model with detailed 1km global map for the geographic distribution of Fe content in soil. We also introduced a parameterization of the Fe processing caused by dust mineralogy, cloud processes and solar radiation. We will present results from simulation experiments in order to explore the model capability to reproduce major observed patterns of deposited Fe into the Atlantic cruises.

  12. Atmospheric black carbon deposition and characterization of biomass burning tracers in a northern temperate forest

    Science.gov (United States)

    Santos, F.; Fraser, M. P.; Bird, J. A.

    2014-10-01

    Aerosol black carbon (BC) is considered the second largest contributor to global warming after CO2, and is known to increase the atmosphere's temperature, decrease the albedo in snow/ice, and influence the properties and distribution of clouds. BC is thought to have a long mean residence time in soils, and its apparent stability may represent a significant stable sink for atmospheric CO2. Despite recent efforts to quantify BC in the environment, the quantification of BC deposition rates from the atmosphere to terrestrial ecosystems remains scarse. To better understand the contribution of atmospheric BC inputs to soils via dry deposition and its dominant emission sources, atmospheric fine particle (PM2.5) were collected at the University of Michigan Biological Station from July to September in 2010 and 2011. PM2.5 samples were analyzed for organic C, BC, and molecular markers including particulate sugars, carboxylic acids, n-alkanes, polycyclic aromatic hydrocarbons, and cholestane. Average atmospheric BC concentrations in northern Michigan were 0.048 ± 0.06 μg m-3 in summer 2010, and 0.049 ± 0.064 μg m-3 in summer 2011. Based on atmospheric concentrations, particulate deposition calculations, and documented soil BC, we conclude that atmospheric deposition is unlikely to comprise a significant input pathway for BC in northern forest ecosystem. The major organic tracers identified in fine particulates (e.g. levoglucosan and docosanoic acid) suggest that ambient PM2.5 concentrations were mainly influenced by biomass burning and epicuticular plant waxes. These results provide baseline data needed for future assessments of atmospheric BC in rural temperate forests.

  13. Benzylammonium Thermometer Ions: Internal Energies of Ions Formed by Low Temperature Plasma and Atmospheric Pressure Chemical Ionization.

    Science.gov (United States)

    Stephens, Edward R; Dumlao, Morphy; Xiao, Dan; Zhang, Daming; Donald, William A

    2015-12-01

    The extent of internal energy deposition upon ion formation by low temperature plasma and atmospheric pressure chemical ionization was investigated using novel benzylammonium thermometer ions. C-N heterolytic bond dissociation enthalpies of nine 4-substituted benzylammoniums were calculated using CAM-B3LYP/6-311++G(d,p), which was significantly more accurate than B3LYP/6-311++G(d,p), MP2/6-311++G(d,p), and CBS-QB3 for calculating the enthalpies of 20 heterolytic dissociation reactions that were used to benchmark theory. All 4-substituted benzylammonium thermometer ions fragmented by a single pathway with comparable dissociation entropies, except 4-nitrobenzylammonium. Overall, the extent of energy deposition into ions formed by low temperature plasma was significantly lower than those formed by atmospheric pressure chemical ionization under these conditions. Because benzylamines are volatile, this new suite of thermometer ions should be useful for investigating the extent of internal energy deposition during ion formation for a wide range of ionization methods, including plasma, spray and laser desorption-based techniques. Graphical Abstract ᅟ.

  14. Atmospheric deposition, CO2, and change in the land carbon sink

    DEFF Research Database (Denmark)

    Martinez-Fernandez, Cristina; Vicca, Sara; Janssens, Ivan A.

    2017-01-01

    Concentrations of atmospheric carbon dioxide (CO2) have continued to increase whereas atmospheric deposition of sulphur and nitrogen has declined in Europe and the USA during recent decades. Using time series of flux observations from 23 forests distributed throughout Europe and the USA......, and generalised mixed models, we found that forest-level net ecosystem production and gross primary production have increased by 1% annually from 1995 to 2011. Statistical models indicated that increasing atmospheric CO2 was the most important factor driving the increasing strength of carbon sinks...... in these forests. We also found that the reduction of sulphur deposition in Europe and the USA lead to higher recovery in ecosystem respiration than in gross primary production, thus limiting the increase of carbon sequestration. By contrast, trends in climate and nitrogen deposition did not significantly...

  15. Selective cytotoxicity of indirect nonequilibrium atmospheric pressure plasma against ovarian clear-cell carcinoma.

    Science.gov (United States)

    Utsumi, Fumi; Kajiyama, Hiroaki; Nakamura, Kae; Tanaka, Hiromasa; Hori, Masaru; Kikkawa, Fumitaka

    2014-01-01

    Ovarian clear cell carcinoma (CCC) is a histological type of epithelial ovarian cancer that is less responsive to chemotherapy and associated with a poorer prognosis than serous and endometrioid carcinoma. Non-thermal atmospheric pressure plasma which produces reactive species has recently led to an explosion of research in plasma medicine. Plasma treatment can be applied to cancer treatment to induce apoptosis and tumor growth arrest. Furthermore, recent studies have shown that a medium exposed to plasma also has an anti-proliferative effect against cancer in the absence of direct exposure to plasma. In this study, we confirmed whether this indirect plasma has an anti-tumor effect against CCC, and investigated whether this efficacy is selective for cancer cells. Non-thermal atmospheric pressure plasma induced apoptosis in CCC cells, while human peritoneal mesothelial cells remained viable. Non-thermal atmospheric pressure plasma exhibits selective cytotoxicity against CCC cells which are resistant to chemotherapy.

  16. Environmental consequences of uranium atmospheric releases from fuel cycle facility: II. The atmospheric deposition of uranium and thorium on plants.

    Science.gov (United States)

    Pourcelot, L; Masson, O; Renaud, P; Cagnat, X; Boulet, B; Cariou, N; De Vismes-Ott, A

    2015-03-01

    Uranium and thorium isotopes were measured in cypress leaves, wheat grains and lettuce taken in the surroundings of the uranium conversion facility of Malvési (South of France). The comparison of activity levels and activity ratios (namely (238)U/(232)Th and (230)Th/(232)Th) in plants with those in aerosols taken at this site and plants taken far from it shows that aerosols emitted by the nuclear site (uranium releases in the atmosphere by stacks and (230)Th-rich particles emitted from artificial ponds collecting radioactive waste mud) accounts for the high activities recorded in the plant samples close to the site. The atmospheric deposition process onto the plants appears to be the dominant process in plant contamination. Dry deposition velocities of airborne uranium and thorium were measured as 4.6 × 10(-3) and 5.0 × 10(-3) m s(-1), respectively.

  17. Characteristics of atmospheric depositions of ionic and carbonaceous components at remote sites in Japan

    Science.gov (United States)

    Sato, K.; Inomata, Y.; Kajino, M.; Tang, N.; Hayakawa, K.; Hakamata, M.; Morisaki, H.

    2015-12-01

    Atmospheric deposition process is important to evaluate lifetimes and budget of atmospheric components. Deposition amounts of sulfur and nitrogen compounds have been evaluated not only in East Asian region but also worldwide. On the other hand, atmospheric deposition of carbonaceous components including organic carbon (OC), elementary carbon (EC) and Polycyclic Aromatic Hydrocarbons (PAHs) were monitored only at a few sites in Europe, North America and Africa, which will obscure removal process and atmospheric concentration distribution of those components. In this study, ionic and carbonaceous components in precipitation and aerosol are monitored at remote sites in Japan, and the characteristics of atmospheric deposition amounts were evaluated.Field observations have been implemented at the Noto station since November 2013 and the Sado station since May 2011. Wet deposition samples were collected by rain samplers, and dry deposition samples were collected by high volume or low volume aerosol samplers. Concentrations of Cl-, NO3-, SO42-, NH4+, Na+, K+, Mg2+, Ca2+ were measured by ion chromatography, EC and OC by the IMPROVE protocol, and PAHs by HPLC with a fluorescence detector. Wet deposition amounts were calculated as the products of aqueous concentration and precipitation amounts, and dry deposition amounts were as the products of aerosol concentrations and deposition velocity estimated by the Inferential Method.Total (wet and dry) annual deposition amounts of carbonaceous components of NO3-, SO42-, EC, water insoluble OC, Fluoranthene at Noto (Nov. 2013 to Oct. 2014) were 4353.81 mg/m2, 7020.50 mg/m2, 149.84 mg/m2, 1191.09 mg/m2, 28.6 μg/m2, respectively. These amounts are comparable total annual deposition amounts of OC and EC at Sado (May 2011 to Feb. 2012), which were 166.04 mg/m2 and 834.0 mg/m2. Higher deposition amounts of ionic and carbonaceous components were observed, which would be attributable to long range transportation of the East Asian

  18. Cathodic cage plasma deposition of TiN and TiO{sub 2} thin films on silicon substrates

    Energy Technology Data Exchange (ETDEWEB)

    Sousa, Romulo R. M. de [Department of Mechanics, Federal Institute of Education, Science, and Technology of Piaui, Praça da Liberdade, 1597, CEP 64000-040 Teresina, Piaui, Brazil and Department of Mechanical Engineering, Federal University of Piaui, Campus Min. Petronio Portela, Ininga, CEP 64049-550 Teresina, Piaui (Brazil); Sato, Patricia S.; Nascente, Pedro A. P., E-mail: nascente@ufscar.br [Department of Materials Engineering, Federal University of Sao Carlos, Via Washington Luis km 235, CEP 13565-905 Sao Carlos, Sao Paulo (Brazil); Viana, Bartolomeu C. [Department of Physics, Federal University of Piaui, Campus Min. Petronio Portela, Ininga, CEP 64049-550 Teresina, Piaui (Brazil); Alves, Clodomiro [Department of Exact and Natural Sciences, Federal Rural University of Semi Arido, Avenida Francisco Mota, 572, CEP 59625-900 Mossoro, Rio Grande do Norte (Brazil); Nishimoto, Akio [Department of Chemistry and Materials Engineering, Faculty of Chemistry, Materials and Bioengineering, Kansai University, 3-3-35 Yamate-cho, Suita, Osaka 564-8680 (Japan)

    2015-07-15

    Cathodic cage plasma deposition (CCPD) was used for growing titanium nitride (TiN) and titanium dioxide (TiO{sub 2}) thin films on silicon substrates. The main advantages of the CCPD technique are the uniformity, tridimensionality, and high rate of the film deposition that occurs at higher pressures, lower temperatures, and lower treatment times than those used in conventional nitriding treatments. In this work, the influence of the temperature and gas atmosphere upon the characteristics of the deposited films was investigated. The TiN and TiO{sub 2} thin films were characterized by x-ray diffraction, scanning electron microscopy, and Raman spectroscopy to analyze their chemical, structural, and morphological characteristics, and the combination of these results indicates that the low-cost CCPD technique can be used to produce even and highly crystalline TiN and TiO{sub 2} films.

  19. Shifts in lake N: P stoichiometry and nutrient limitation driven by atmospheric nitrogen deposition

    Science.gov (United States)

    Elser, J.J.; Andersen, T.; Baron, J.S.; Bergstrom, A.-K.; Jansson, M.; Kyle, M.; Nydick, K.R.; Steger, L.; Hessen, D.O.

    2009-01-01

    Human activities have more than doubled the amount of nitrogen (N) circulating in the biosphere. One major pathway of this anthropogenic N input into ecosystems has been increased regional deposition from the atmosphere. Here we show that atmospheric N deposition increased the stoichiometric ratio of N and phosphorus (P) in lakes in Norway, Sweden, and Colorado, United States, and, as a result, patterns of ecological nutrient limitation were shifted. Under low N deposition, phytoplankton growth is generally N-limited; however, in high-N deposition lakes, phytoplankton growth is consistently P-limited. Continued anthropogenic amplification of the global N cycle will further alter ecological processes, such as biogeochemical cycling, trophic dynamics, and biological diversity, in the world's lakes, even in lakes far from direct human disturbance.

  20. Atmospheric wet and litterfall mercury deposition at urban and rural sites in China

    Science.gov (United States)

    Fu, Xuewu; Yang, Xu; Lang, Xiaofang; Zhou, Jun; Zhang, Hui; Yu, Ben; Yan, Haiyu; Lin, Che-Jen; Feng, Xinbin

    2016-09-01

    Mercury (Hg) concentrations and deposition fluxes in precipitation and litterfall were measured at multiple sites (six rural sites and an urban site) across a broad geographic area in China. The annual deposition fluxes of Hg in precipitation at rural sites and an urban site were 2.0 to 7.2 and 12.6 ± 6.5 µg m-2 yr-1, respectively. Wet deposition fluxes of Hg at rural sites showed a clear regional difference with elevated deposition fluxes in the subtropical zone, followed by the temporal zone and arid/semi-arid zone. Precipitation depth is the primary influencing factor causing the variation of wet deposition. Hg fluxes through litterfall ranged from 22.8 to 62.8 µg m-2 yr-1, higher than the wet deposition fluxes by a factor of 3.9 to 8.7 and representing approximately 75 % of the total Hg deposition at the forest sites in China. This suggests that uptake of atmospheric Hg by foliage is the dominant pathway to remove atmospheric Hg in forest ecosystems in China. Wet deposition fluxes of Hg at rural sites of China were generally lower compared to those in North America and Europe, possibly due to a combination of lower precipitation depth, lower GOM concentrations in the troposphere and the generally lower cloud base heights at most sites that wash out a smaller amount of GOM and PBM during precipitation events.

  1. Growth of γ-alumina thin films by pulsed laser deposition and plasma diagnostic

    Science.gov (United States)

    Yahiaoui, K.; Abdelli-Messaci, S.; Messaoud Aberkane, S.; Siad, M.; Kellou, A.

    2017-07-01

    The present work discusses about the synthesis of alumina thin films, which have applications in current and next-generation solid-state electronic devices due to their attractive properties. Alumina thin films were synthesized by pulsed laser deposition at different oxygen pressures and substrate temperatures. The dependence of substrate temperature, oxygen pressure, and the deposition time on the properties of the films has been observed by growing three series of alumina thin films on Si (100). The first films are synthesized using substrate temperatures ranging from room temperature to 780 °C at 0.01 mbar of O2. The second series was realized at a fixed substrate temperature of 760 °C and varied oxygen pressure (from 0.005 to 0.05 mbar). The third set of series was elaborated at different deposition times (from 15 to 60 min) while the oxygen pressure and the substrate temperature were fixed at 0.01 mbar and 760 °C, respectively. The films were characterized using X-ray diffractometer (XRD) for structural analysis, a scanning electron microscope for morphological analysis, a nano-indenter for mechanical analysis (hardness and Young's modulus), and Rutherford backscattering spectroscopy for thickness and stoichiometry measurements. Using optical emission spectroscopy, plasma diagnostic was carried out both in the vacuum and in the presence of oxygen with a pressure ranging from 0.01 to 0.05 mbar. Several neutral, ionic, and molecular species were identified such as Al, Al+, and Al++ in vacuum and in oxygen ambiance, O and AlO molecular bands in oxygen-ambient atmosphere. The spatiotemporal evolution of the most relevant species was achieved and their velocities were estimated. The highest amount of crystallized alumina in γ-phase was found in the films elaborated under 0.01 mbar of O2, at a substrate temperature of 780 °C, and a deposition time of 60 min.

  2. Atmospheric deposition in coniferous and deciduous tree stands in Poland

    Science.gov (United States)

    Kowalska, Anna; Astel, Aleksander; Boczoń, Andrzej; Polkowska, Żaneta

    2016-05-01

    The objective of this study was to assess the transformation of precipitation in terms of quantity and chemical composition following contact with the crown layer in tree stands with varied species composition, to investigate the effect of four predominant forest-forming species (pine, spruce, beech, and oak) on the amount and composition of precipitation reaching forest soils, and to determine the sources of pollution in atmospheric precipitation in forest areas in Poland. The amount and chemical composition (pH, electric conductivity, alkalinity, and chloride, nitrate, sulfate, phosphate, ammonium, calcium, magnesium, sodium, potassium, iron aluminum, manganese, zinc, copper, total nitrogen, and dissolved organic carbon contents) of atmospheric (bulk, BP) and throughfall (TF) precipitation were studied from January to December 2010 on twelve forest monitoring plots representative of Polish conditions. The study results provided the basis for the determination of the fluxes of pollutants in the forest areas of Poland and allowed the comparison of such fluxes with values provided in the literature for European forest areas. The transformation of precipitation in the canopy was compared for different tree stands. The fluxes of substances in an open field and under canopy were influenced by the location of the plot, including the regional meteorological conditions (precipitation amounts), vicinity of the sea (effect of marine aerosols), and local level of anthropogenic pollution. Differences between the plots were higher in TF than in BP. The impact of the vegetation cover on the chemical composition of precipitation depended on the region of the country and dominant species in a given tree stand. Coniferous species tended to cause acidification of precipitation, whereas deciduous species increased the pH of TF. Pine and oak stands enriched precipitation with components that leached from the canopy (potassium, manganese, magnesium) to a higher degree than spruce and

  3. VOC removal by plasma-photocatalyst combination : comparison between a low and an atmospheric pressure plasma.

    Science.gov (United States)

    Rousseau, Antoine; Guaitella, Olivier; Gatilova, Lina; Thevenet, Frederic; Guillard, Chantal; Hannemann, Mario; Roepcke, Jurgen

    2004-09-01

    The combination of a non thermal plasma with a photo-catalyst is promising for VOC and odour abatement at room temperature and at a very low energy cost. In classical photocatalysis, UV photons generate an electron hole pair on the surface of the photo-catalyst (TiO2), which generates primary radicals responsible of VOC oxidation. In plasma-photocatalysis combination, activation mechanisms of the photocatalytic surface are not clearly identified to the day. Our strategy is to compare a pulsed DBD at atmospheric pressure containing TiO2 pellets, with a pulsed low pressure DC discharge in contact with a porous TiO2 surface. These two discharge are characterized electrically and the efficiency of VOC removal is performed using infrared laser absorption spectroscopy and gas chromatography.

  4. TiOxNy coatings grown by atmospheric pressure metal organic chemical vapor deposition

    OpenAIRE

    Maury, Francis; Duminica, Florin-Daniel

    2010-01-01

    International audience; Titanium oxynitride coatings were deposited on various substrates by an original atmospheric pressure metal organic chemical vapor deposition (MOCVD) process using titanium tetra-iso-propoxide as titanium and oxygen precursors and hydrazine as a nitrogen source. The films composition was monitored by controlling the N2H4 mole fraction in the initial reactive gas phase. The variation of the N content in the films results in significant changes in morphological, structur...

  5. Atmospheric transport and deposition of pesticides: An assessment of current knowledge

    DEFF Research Database (Denmark)

    Pul, W.A.J. van; Bidleman, T.F.; Brorström-Lunden, E.

    1999-01-01

    there is a shortage of measurement data to evaluate the deposition and reemission processes. It was concluded that the mechanisms of transport and dispersion of pesticides can be described similarly to those for other air pollution components and these mechanisms are rather well-known. Large uncertainties are present......The current knowledge on atmospheric transport and deposition of pesticides is reviewed and discussed by a working group of experts during the Workshop on Fate of pesticides in the atmosphere; implications for risk assessment, held in Driebergen, the Netherlands, 22-24 April, 1998. In general...

  6. Atmospheric heavy metal deposition accumulated in rural forest soils of southern Scandinavia

    DEFF Research Database (Denmark)

    Hovmand, Mads Frederik; Kemp, Kaare; Kystol, J.

    2008-01-01

    Thirty-three years of measurements of atmospheric heavy metal (HM) deposition (bulk precipitation) in Denmark combined with European emission inventories form the basis for calculating a 50-year accumulated atmospheric input to a remote forest plantation on the island of Laesoe. Soil samples taken...... in two depths, 0-10 cm and 10-20 cm, at eight forest sites at the island were used to determine the increase in HM content in the eolian deposited top soils of the plantation. Concentrations of lead (Pb), cadmium (Cd), copper (Cu), zinc (Zn), vanadium (V), nickel (Ni) and arsenic (As) were determined...

  7. Atmospheric deposition and critical loads for nitrogen and metals in Arctic Alaska: Review and current status

    Science.gov (United States)

    Linder, Greg L.; Brumbaugh, William G.; Neitlich, Peter; Little, Edward

    2013-01-01

    To protect important resources under their bureau’s purview, the United States National Park Service’s (NPS) Arctic Network (ARCN) has developed a series of “vital signs” that are to be periodically monitored. One of these vital signs focuses on wet and dry deposition of atmospheric chemicals and further, the establishment of critical load (CL) values (thresholds for ecological effects based on cumulative depositional loadings) for nitrogen (N), sulfur, and metals. As part of the ARCN terrestrial monitoring programs, samples of the feather moss Hylocomium splendens are being col- lected and analyzed as a cost-effective means to monitor atmospheric pollutant deposition in this region. Ultimately, moss data combined with refined CL values might be used to help guide future regulation of atmospheric contaminant sources potentially impacting Arctic Alaska. But first, additional long-term studies are needed to determine patterns of contaminant deposition as measured by moss biomonitors and to quantify ecosystem responses at particular loadings/ ranges of contaminants within Arctic Alaska. Herein we briefly summarize 1) current regulatory guidance related to CL values 2) derivation of CL models for N and metals, 3) use of mosses as biomonitors of atmospheric deposition and loadings, 4) preliminary analysis of vulnerabilities and risks associated with CL estimates for N, 5) preliminary analysis of existing data for characterization of CL values for N for interior Alaska and 6) implications for managers and future research needs.

  8. Impact of acid atmospheric deposition on soils: Field monitoring and aluminium chemistry.

    OpenAIRE

    1988-01-01

    The effect of acid atmospheric deposition on concentrations and transfer of major solutes in acid, sandy soils was studied. Emphasis was given to mobilization and transport of potentially toxic aluminum. Data on solute concentrations and fluxes in meteoric water as well as soil solutions were obtained from intensive monitoring programmes conducted at a number of sites in northwestern Europe and North-America. Specific hypotheses were tested in laboratory experiments.Atmospheric acid inputs do...

  9. Western Pacific atmospheric nutrient deposition fluxes, their impact on surface ocean productivity

    Science.gov (United States)

    Martino, M.; Hamilton, D.; Baker, A. R.; Jickells, T. D.; Bromley, T.; Nojiri, Y.; Quack, B.; Boyd, P. W.

    2014-07-01

    The atmospheric deposition of both macronutrients and micronutrients plays an important role in driving primary productivity, particularly in the low-latitude ocean. We report aerosol major ion measurements for five ship-based sampling campaigns in the western Pacific from ~25°N to 20°S and compare the results with those from Atlantic meridional transects (~50°N to 50°S) with aerosols collected and analyzed in the same laboratory, allowing full incomparability. We discuss sources of the main nutrient species (nitrogen (N), phosphorus (P), and iron (Fe)) in the aerosols and their stoichiometry. Striking north-south gradients are evident over both basins with the Northern Hemisphere more impacted by terrestrial dust sources and anthropogenic emissions and the North Atlantic apparently more impacted than the North Pacific. We estimate the atmospheric supply rates of these nutrients and the potential impact of the atmospheric deposition on the tropical western Pacific. Our results suggest that the atmospheric deposition is P deficient relative to the needs of the resident phytoplankton. These findings suggest that atmospheric supply of N, Fe, and P increases primary productivity utilizing some of the residual excess phosphorus (P*) in the surface waters to compensate for aerosol P deficiency. Regional primary productivity is further enhanced via the stimulation of nitrogen fixation fuelled by the residual atmospheric iron and P*. Our stoichiometric calculations reveal that a P* of 0.1 µmol L-1 can offset the P deficiency in atmospheric supply for many months. This study suggests that atmospheric deposition may sustain ~10% of primary production in both the western tropical Pacific.

  10. Effect of process parameters on induction plasma reactive deposition of tungsten carbide from tungsten metal powder

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Tungsten carbide deposit was made directly from tungsten metal powder through the reaction with methane in radio frequency induction plasma. Effect of major process parameters on the induction plasma reactive deposition of tungsten carbide was studied by optical microscopy, scanning electron microscopy, X-ray diffraction analysis, water displacement method, and microhardness test. The results show that methane flow rate, powder feed rate, particle size, reaction chamber pressure and deposition distance have significant influences on the phase composition, density, and microhardness of the deposit. Extra carbon is necessary to ensure the complete conversion of tungsten metal into the carbide.

  11. A 3D parameterization of iron atmospheric deposition to the global ocean

    Science.gov (United States)

    Myriokefalitakis, Stelios; Krol, Maarten C.; van Noije, Twan P. C.; Le Sager, Philippe

    2017-04-01

    Atmospheric deposition of trace constituents, both of natural and anthropogenic origin, can act as a nutrient source into the open ocean and affect marine ecosystem functioning and subsequently the exchange of CO2 between the atmosphere and the global ocean. Dust is known as a major source of nutrients to the global ocean, but only a fraction of these nutrients is released in soluble form that can be assimilated by the ecosystems. Iron (Fe) is a key micronutrient that significantly modulates gross primary production in High-Nutrient-Low-Chlorophyll (HNLC) oceans, where macronutrients like nitrate are abundant but primary production is limited by Fe scarcity. The global atmospheric Fe cycle is here parameterized in the state-of-the-art global Earth System Model EC-Earth. The model takes into account the primary emissions of both insoluble and soluble Fe, associated with dusts and combustion processes. The impact of atmospheric acidity on mineral solubility is parameterized based on updated experimental and theoretical findings, and model results are evaluated against available observations. The link between the soluble Fe atmospheric deposition and anthropogenic sources is also investigated. Overall, the response of the chemical composition of nutrient containing aerosols to atmospheric composition changes is demonstrated and quantified. This work has been financed by the Marie-Curie H2020-MSCA-IF-2015 grant (ID 705652) ODEON (Online DEposition over OceaNs: Modeling the effect of air pollution on ocean bio-geochemistry in an Earth System Model).

  12. Diamond-like Carbon Thin Films Deposited on Ti6Al4V Alloy Surface by Plasma Gun at Atmospheric Pressure%钛合金表面大气压等离子体枪制备类金刚石薄膜

    Institute of Scientific and Technical Information of China (English)

    陈飞; 周海; 张跃飞; 吕反修

    2012-01-01

    在大气下,采用大气压介质阻挡放电(DBD)等离子体枪在低温下<350℃),以甲烷为单体,氩气为工作气体,在Ti6Al4V钛合金表面制备一层类金刚石薄膜(DLC),以期改善钛合金表面摩擦学性能.利用激光拉曼(Raman)光谱和X射线光电子能谱(XPS)分析了所制备DLC薄膜的结构;利用扫描电子显微镜(SEM)观察DLC薄膜的表面形貌;利用划痕仪测量了DLC薄膜与基体的结合力;利用球-盘摩擦磨损实验仪对DLC薄膜的耐磨性能进行了研究.结果表明:在本实验工艺条件下沉积的类金刚石薄膜厚度约为1.0 μm,薄膜均匀且致密,表面粗糙度Ra为13.23 nm.类金刚石薄膜与基体结合力的临界载荷达到31.0N.DLC薄膜具有优良的减摩性,Ti6Al4V表面沉积DLC薄膜后摩擦系数为0.15,较Ti6Al4V基体的摩擦系数0.50明显减小,耐磨性能得到提高.%At atmospheric pressure, diamond-like carbon (DLC) thin films were deposited on the T16A14V alloy surface by a DBD plasma gun at low temperature (<350℃), with CH4 as a precursor and Ar as dilution gas. The structure of the DLC thin film was analyzed by Laser Raman spectroscope and X-ray photoelectron spectroscopy. The surface morphology was observed through scanning electron microscopy. The adhesion between the DLC thin film and the substrate was investigated with the scribe testing. The friction and wear behavior of the DLC thin films under dry sliding against GCrlS steel was evaluated on a ball-on-disc test rig. The results show that it is feasible to prepare a DLC thin film of 1.0 um thickness by a plasma gun. The film is uniform and dense and the surface roughness R. Is about 13.23 nm. The critical load of adhesion force between the DLC thin film and the substrate is 31.0 N. It has been found that the DLC thin film has excellent friction- and wear-resistant behavior. The friction coefficient of the Ti6A14V substrate is about 0.50 under dry sliding against steel, while the DLC thin

  13. Cold atmospheric plasma - A new technology for spacecraft component decontamination

    Science.gov (United States)

    Shimizu, Satoshi; Barczyk, Simon; Rettberg, Petra; Shimizu, Tetsuji; Klaempfl, Tobias; Zimmermann, Julia L.; Hoeschen, Till; Linsmeier, Christian; Weber, Peter; Morfill, Gregor E.; Thomas, Hubertus M.

    2014-01-01

    Cold atmospheric plasma (CAP) based on the Surface Micro-Discharge (SMD) technology was investigated for inactivation of different bacteria and endospores. The used technique was developed to serve as an alternative method for the decontamination of spacecraft components based on the COSPAR planetary protection policy where currently the dry heat microbial reduction method is the only applicable way to satisfy the required demands. However it is known, that dry heat can thermally damage sophisticated components installed on the device. Therefore, the development of a low temperature sterilization system is one of the high priority issues for upcoming space missions in the extraterrestrial field. In the study presented here, the vegetative bacteria Escherichia coli and Deinococcus radiodurans and several types of bacterial endospores - including Bacillus atrophaeus, Bacillus safensis, Bacillus megaterium, Bacillus megaterium 2c1 and Bacillus thuringiensis E24 - were inactivated by exposing them indirectly i.e. only to the reactive gases produced by the SMD electrode at room temperature. The results showed a 5 log inactivation for E. coli after 10 min of exposure. In contrast D. radiodurans proved to be more resistant resulting in a reduction of 3 log after exposure of 30 min. More than 6 log reductions were achieved for B. safensis, B. megaterium and B. megaterium 2c1 after 90 min of exposure. Furthermore the applicability of the used CAP system for spacecraft decontamination according to the planetary protection policy was investigated. This included also the investigation of the inactivation homogeneity by the plasma gas, the control of the temperature at the area of interest, the measurement of the O3 density in the treatment region and the detailed investigation of the effects of the exposure on different materials.

  14. High-rate diamond deposition by microwave plasma CVD

    Science.gov (United States)

    Li, Xianglin

    In this dissertation, the growth of CVD (Chemical Vapor Deposition) diamond thin films is studied both theoretically and experimentally. The goal of this research is to deposit high quality HOD (Highly Oriented Diamond) films with a growth rate greater than 1 mum/hr. For the (100)-oriented HOD films, the growth rate achieved by the traditional process is only 0.3 mum/hr while the theoretical limit is ˜0.45 mum/hr. This research increases the growth rate up to 5.3 mum/hr (with a theoretical limit of ˜7 mum/hr) while preserving the crystal quality. This work builds a connection between the theoretical study of the CVD process and the experimental research. The study is extended from the growth of regular polycrystalline diamond to highly oriented diamond (HOD) films. For the increase of the growth rate of regular polycrystalline diamond thin films, a scaling growth model developed by Goodwin is introduced in details to assist in the understanding of the MPCVD (Microwave Plasma CVD) process. Within the Goodwin's scaling model, there are only four important sub-processes for the growth of diamond: surface modification, adsorption, desorption, and incorporation. The factors determining the diamond growth rate and film quality are discussed following the description of the experimental setup and process parameters. Growth rate and crystal quality models are reviewed to predict and understand the experimental results. It is shown that the growth rate of diamond can be increased with methane input concentration and the amount of atomic hydrogen (by changing the total pressure). It is crucial to provide enough atomic hydrogen to conserve crystal quality of the deposited diamond film. The experimental results demonstrate that for a fixed methane concentration, there is a minimum pressure for growth of good diamond. Similarly, for a fixed total pressure, there is a maximum methane concentration for growth of good diamond, and this maximum methane concentration increases

  15. Fabrication of Al doped ZnO films using atmospheric pressure cold plasma

    Energy Technology Data Exchange (ETDEWEB)

    Suzaki, Yoshifumi, E-mail: suzaki@eng.kagawa-u.ac.jp [Faculty of Engineering, Kagawa University, Hayashi-cho 2217-20, Takamatsu, Kagawa 761-0396 (Japan); Miyagawa, Hayato; Yamaguchi, Kenzo [Faculty of Engineering, Kagawa University, Hayashi-cho 2217-20, Takamatsu, Kagawa 761-0396 (Japan); Kim, Yoon-Kee [Dept. of Welding and Production Engineering, Hanbat National University, San 16-1, Duckmyoung-dong, Yuseong-gu, Daejeon 305-719 (Korea, Republic of)

    2012-11-01

    Under atmospheric pressure, homogeneous non-equilibrium cold plasma was generated stably by high voltage pulsed power (1 kV, 20 kHz, 38 W) excitation of a mixture of He and O{sub 2} gases produced by a dielectric barrier discharge setup. By feeding Bis (2 methoxy-6-methyl-3, 5-heptanedione) Zn (Zn-MOPD, C{sub 18}H{sub 3}O{sub 6}Zn) and Tris (2-methoxy-6-methy l-3, 5-heptanedione) Al (Al-MOPD, C{sub 27}H{sub 45}O{sub 9}Al) into this plasma with He carrier gas, transparent flat Al-doped ZnO (ZnO:Al) films about 120-240 nm thick were prepared on glass substrates directly under the slit made into the cathode. Deposition rates of the films were about 20-40 nm/min. The concentration of Al was measured by inductively coupled plasma atomic emission spectroscopy. The composition ratio of Al to Zn was 7.8 mol% when the carrier He gas flow rate of Al-MOPD was 30 cm{sup 3}. The average transmittance of all films was more than 85% in the wavelength range from 400 to 800 nm. When the composition ratio of Al/Zn was between 1.1 and 7.8 mol%, the optical band gap of the film increased from 3.28 to 3.40 eV. The resistivity of ZnO:Al film was 2.96 {Omega} cm at 1.3 mol% of Al/Zn. In addition, the microstructure of the films was studied by X-ray diffraction measurement and field emission scanning electron microscope observation. It was revealed that doped Al is substituted onto the Zn site of the ZnO crystalline structure in ZnO:Al films. - Highlights: Black-Right-Pointing-Pointer An atmospheric pressure cold plasma generator generated stable glow discharge. Black-Right-Pointing-Pointer We fabricated Al doped ZnO films on glass substrates using cold plasma. Black-Right-Pointing-Pointer Al concentration measured by inductively coupled plasma atomic emission spectroscopy. Black-Right-Pointing-Pointer The transmission spectrum and the resistivity of the films were measured. Black-Right-Pointing-Pointer The microstructure of the films was studied.

  16. Atmospheric dry deposition in the vicinity of the Salton Sea, California - I: Air pollution and deposition in a desert environment

    Science.gov (United States)

    Alonso, R.; Bytnerowicz, A.; Boarman, W.I.

    2005-01-01

    Air pollutant concentrations and atmospheric dry deposition were monitored seasonally at the Salton Sea, southern California. Measurements of ozone (O 3), nitric acid vapor (HNO3), ammonia (NH3), nitric oxide (NO), nitrogen dioxide (NO2) and sulfur dioxide (SO 2) were performed using passive samplers. Deposition rates of NO 3-, NH4+, Cl-, SO 42-, Na+, K+ and Ca2+ to creosote bush branches and nylon filters as surrogate surfaces were determined for one-week long exposure periods. Maximum O3 values were recorded in spring with 24-h average values of 108.8 ??g m-3. Concentrations of NO and NO2 were low and within ranges of the non-urban areas in California (0.4-5.6 and 3.3-16.2 ??g m-3 ranges, respectively). Concentrations of HNO3 (2.0-6.7 ??g m-3) and NH 3 (6.4-15.7 ??g m-3) were elevated and above the levels typical for remote locations in California. Deposition rates of Cl-, SO42-, Na+, K+ and Ca2+ were related to the influence of sea spray or to suspended soil particles, and no strong enrichments caused by ions originated by human activities were detected. Dry deposition rates of NO3- and NH4+ were similar to values registered in areas where symptoms of nitrogen saturation and changes in species composition have been described. Deposition of nitrogenous compounds might be contributing to eutrophication processes at the Salton Sea. ?? 2005 Elsevier Ltd. All rights reserved.

  17. Novel Prospects for Plasma Spray-Physical Vapor Deposition of Columnar Thermal Barrier Coatings

    Science.gov (United States)

    Anwaar, Aleem; Wei, Lianglinag; Guo, Qian; Zhang, Baopeng; Guo, Hongbo

    2017-09-01

    Plasma spray-physical vapor deposition (PS-PVD) is an emerging coating technique that can produce columnar thermal barrier coatings from vapor phase. Feedstock treatment at the start of its trajectory in the plasma torch nozzle is important for such vapor-phase deposition. This study describes the effects of the plasma composition (Ar/He) on the plasma characteristics, plasma-particle interaction, and particle dynamics at different points spatially distributed inside the plasma torch nozzle. The results of calculations show that increasing the fraction of argon in the plasma gas mixture enhances the momentum and heat flow between the plasma and injected feedstock. For the plasma gas combination of 45Ar/45He, the total enthalpy transferred to a representative powder particle inside the plasma torch nozzle is highest ( 9828 kJ/kg). Moreover, due to the properties of the plasma, the contribution of the cylindrical throat, i.e., from the feed injection point (FIP) to the start of divergence (SOD), to the total transferred energy is 69%. The carrier gas flow for different plasma gas mixtures was also investigated by optical emission spectroscopy (OES) measurements of zirconium emissions. Yttria-stabilized zirconia (YSZ) coating microstructures were produced when using selected plasma gas compositions and corresponding carrier gas flows; structural morphologies were found to be in good agreement with OES and theoretical predictions. Quasicolumnar microstructure was obtained with porosity of 15% when applying the plasma composition of 45Ar/45He.

  18. Atmospheric growth of ZnO films deposited by spray pyrolysis using diethylzinc solution

    Science.gov (United States)

    Imai, Masato; Watanabe, Marin; Mochihara, Akiko; Tominaga, Himeka; Yoshino, Kenji; Shen, Qing; Toyoda, Taro; Hayase, Shuzi

    2017-06-01

    Non-doped ZnO thin films are deposited on glass substrates by spray pyrolysis using diethylzinc solution at a range from a room temperature to 150 °C while making N2 gas flow in atmospheric pressure. The morphology, the structural property, the density and the optical band gap are studied. As the deposition temperature is increasing, the overall density and the optical band gap approach to the values of ZnO single crystal. The quality of ZnO thin film deposited at 150 °C becomes near ZnO single crystal.

  19. Physico Chemical Characteristics of High Performance Polymer Modified by Low and Atmospheric Pressure Plasma1

    OpenAIRE

    N Bhatnagar; Jha, S.; Bhowmik, S.; Gupta, G.; Moon, J.B.; Kim, C.G.

    2012-01-01

    In this work, the effect of low pressure plasma and atmospheric-pressure plasma treatment on surface properties and adhesion characteristics of high performance polymer, Polyether Ether Ketone (PEEK) are investigated in terms of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Atomic Force Microscopy (AFM). The experimental results show that the PEEK surface treated by atmospheric pressure plasma lead to an increase in the polar component of the surf...

  20. Physico-chemical characteristics of high performance polymer modified by low and atmospheric pressure plasma

    OpenAIRE

    Nitu, Bhatnagar; Sangeeta, Jha; Shantanu, Bhowmik; Govind, Gupta; Moon, J.; Kim, C

    2012-01-01

    In this work, the effect of low pressure plasma and atmospheric-pressure plasma treatment on surface properties and adhesion characteristics of high performance polymer, Polyether Ether Ketone (PEEK) are investigated in terms of Fourier Transform Infrared Spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS), and Atomic Force Microscopy (AFM). The experimental results show that the PEEK surface treated by atmospheric pressure plasma lead to an increase in the polar component of the surf...

  1. Atmospheric deposition of nitrogen over Czech forests: refinement of estimation of dry deposition for unmeasured nitrogen species

    Science.gov (United States)

    Hunova, Iva; Stoklasova, Petra; Kurfurst, Pavel; Vlcek, Ondrej; Schovankova, Jana

    2014-05-01

    The accurate quantification of atmospheric deposition is very important for assessment of ambient air pollution impacts on ecosystems. Our contribution presents an advanced approach to improved quantification of atmospheric deposition of nitrogen over Czech forests, merging available measured data and model results. The ambient air quality monitoring in the Czech Republic is paid an appreciable attention (Hůnová, 2001) due to the fact, that in the recent past its territory belonged to the most polluted parts of Europe (Moldan and Schnoor, 1992). The time trends and spatial patterns of atmospheric deposition were published (Hůnová et al. 2004, Hůnová et al. 2014). Nevertheless, it appears that the atmospheric deposition of nitrogen, particularly the dry deposition, is likely to be underestimated due to unavailability of data of certain nitrogen species as HNO3(g) and NH3. It is known that HNO3(g) may contribute significantly to the dry deposition of nitrogen even in regions with relatively low concentrations (Flechard et al., 2011). We attempted to substitute unmeasured nitrogen species using an Eulerian photochemical dispersion model CAMx, the Comprehensive Air Quality Model with extensions (ESSS, 2011), coupled with a high resolution regional numeric weather prediction model Aladin (Vlček, Corbet, 2011). Preliminary results for 2008 indicate that dry deposition of nitrogen, so far based on detailed monitoring of ambient NOx levels, is underestimated substantially. The dry deposition of N/NOx in 2008 reported by Ostatnická (2009) was about 0.5 g.m-2.year-1 over 99.5 % of the nation-wide area, while the contribution of unmeasured nitrogen species estimated by CAMx model were much higher. To be specific, the dry deposition of N/HNO3(g) accounted for 1.0 g.m-2.year-1, and N/NH3 for 1.6 g.m-2.year-1. In contrast, the deposition of N/HONO (g) with 0.001 g.m-2.year-1, N/PAN with 0.007 g.m-2.year-1, particulate N/NO3- with 0.002 g.m-2.year-1, and particulate N/NH4

  2. Lichen-based critical loads for atmospheric nitrogen deposition in Western Oregon and Washington Forests, USA

    Energy Technology Data Exchange (ETDEWEB)

    Geiser, Linda H., E-mail: lgeiser@fs.fed.u [US Forest Service Pacific Northwest Region Air Resource Management Program, Siuslaw National Forest, PO Box 1148, Corvallis, OR 97339 (United States); Jovan, Sarah E. [US Forest Service Forest Inventory and Analysis Program, Pacific Northwest Research Station, 620 SW Main St, Suite 400, Portland, OR 97205 (United States); Glavich, Doug A. [US Forest Service Pacific Northwest Region Air Resource Management Program, Siuslaw National Forest, PO Box 1148, Corvallis, OR 97339 (United States); Porter, Matthew K. [Laboratory for Atmospheric Research, Washington State University, Pullman, WA 99164 (United States)

    2010-07-15

    Critical loads (CLs) define maximum atmospheric deposition levels apparently preventative of ecosystem harm. We present first nitrogen CLs for northwestern North America's maritime forests. Using multiple linear regression, we related epiphytic-macrolichen community composition to: 1) wet deposition from the National Atmospheric Deposition Program, 2) wet, dry, and total N deposition from the Communities Multi-Scale Air Quality model, and 3) ambient particulate N from Interagency Monitoring of Protected Visual Environments (IMPROVE). Sensitive species declines of 20-40% were associated with CLs of 1-4 and 3-9 kg N ha{sup -1} y{sup -1} in wet and total deposition. CLs increased with precipitation across the landscape, presumably from dilution or leaching of depositional N. Tight linear correlation between lichen and IMPROVE data suggests a simple screening tool for CL exceedance in US Class I areas. The total N model replicated several US and European lichen CLs and may therefore be helpful in estimating other temperate-forest lichen CLs. - Lichen-based critical loads for N deposition in western Oregon and Washington forests ranged from 3 to 9 kg ha{sup -1} y{sup -1}, increasing with mean annual precipitation.

  3. Atmospheric-pressure plasma activation and surface characterization on polyethylene membrane separator

    Science.gov (United States)

    Tseng, Yu-Chien; Li, Hsiao-Ling; Huang, Chun

    2017-01-01

    The surface hydrophilic activation of a polyethylene membrane separator was achieved using an atmospheric-pressure plasma jet. The surface of the atmospheric-pressure-plasma-treated membrane separator was found to be highly hydrophilic realized by adjusting the plasma power input. The variations in membrane separator chemical structure were confirmed by Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Chemical analysis showed newly formed carbonyl-containing groups and high surface concentrations of oxygen-containing species on the atmospheric-pressure-plasma-treated polymeric separator surface. It also showed that surface hydrophilicity primarily increased from the polar component after atmospheric-pressure plasma treatment. The surface and pore structures of the polyethylene membrane separator were examined by scanning electron microscopy, revealing a slight alteration in the pore structure. As a result of the incorporation of polar functionalities by atmospheric-pressure plasma activation, the electrolyte uptake and electrochemical impedance of the atmospheric-pressure-plasma-treated membrane separator improved. The investigational results show that the separator surface can be controlled by atmospheric-pressure plasma surface treatment to tailor the hydrophilicity and enhance the electrochemical performance of lithium ion batteries.

  4. Effect of microwave frequency on plasma formation in air breakdown at atmospheric pressure

    Institute of Scientific and Technical Information of China (English)

    赵朋程; 郭立新; 李慧敏

    2015-01-01

    Microwave breakdown at atmospheric pressure causes the formation of a discrete plasma structure. The one-dimensional fluid model coupling Maxwell equations with plasma fluid equations is used to study the effect of the mi-crowave frequency on the formation of air plasma. Simulation results show that, the filamentary plasma array propagating toward the microwave source is formed at different microwave frequencies. As the microwave frequency decreases, the ratio of the distance between two adjacent plasma filaments to the corresponding wavelength remains almost unchanged (on the order of 1/4), while the plasma front propagates more slowly due to the increase in the formation time of the new plasma filament.

  5. Experimental characterization of an argon laminar plasma jet at atmospheric pressure

    Energy Technology Data Exchange (ETDEWEB)

    Langlois-Bertrand, Emilie; De Izarra, Charles, E-mail: charles.de_izarra@univ-orleans.fr [Groupe de Recherche sur l' Energetique des Milieux Ionises, UMR6606 Universite d' Orleans - CNRS, Faculte des Sciences, Site de Bourges, rue Gaston Berger, BP 4043, 18028 BOURGES Cedex (France)

    2011-10-19

    This paper deals with a dc laminar pure argon plasma jet operating at atmospheric pressure in ambient air that was experimentally studied in order to obtain temperature and velocity. Plasma jet temperature was evaluated by optical emission spectroscopy and the plasma jet velocity was determined by various methods using a pressure sensor. It is shown that the maximum plasma jet temperature is 15 000 K and the maximum plasma jet velocity is 250 m s{sup -1} at the plasma jet centre. Finally, a study of the ambient air amount entrained into the plasma jet is presented.

  6. Conditional vulnerability of plant diversity to atmospheric nitrogen deposition across the United States

    Science.gov (United States)

    Simkin, Samuel M.; Allen, Edith B.; Bowman, William D.; Clark, Christopher M.; Belnap, Jayne; Brooks, Matthew L.; Cade, Brian S.; Collins, Scott L.; Geiser, Linda H.; Gilliam, Frank S.; Jovan, Sarah E.; Pardo, Linda H.; Schulz, Bethany K.; Stevens, Carly J.; Suding, Katharine N.; Throop, Heather L.; Waller, Donald M.

    2016-01-01

    Atmospheric nitrogen (N) deposition has been shown to decrease plant species richness along regional deposition gradients in Europe and in experimental manipulations. However, the general response of species richness to N deposition across different vegetation types, soil conditions, and climates remains largely unknown even though responses may be contingent on these environmental factors. We assessed the effect of N deposition on herbaceous richness for 15,136 forest, woodland, shrubland, and grassland sites across the continental United States, to address how edaphic and climatic conditions altered vulnerability to this stressor. In our dataset, with N deposition ranging from 1 to 19 kg N⋅ha−1⋅y−1, we found a unimodal relationship; richness increased at low deposition levels and decreased above 8.7 and 13.4 kg N⋅ha−1⋅y−1 in open and closed-canopy vegetation, respectively. N deposition exceeded critical loads for loss of plant species richness in 24% of 15,136 sites examined nationwide. There were negative relationships between species richness and N deposition in 36% of 44 community gradients. Vulnerability to N deposition was consistently higher in more acidic soils whereas the moderating roles of temperature and precipitation varied across scales. We demonstrate here that negative relationships between N deposition and species richness are common, albeit not universal, and that fine-scale processes can moderate vegetation responses to N deposition. Our results highlight the importance of contingent factors when estimating ecosystem vulnerability to N deposition and suggest that N deposition is affecting species richness in forested and nonforested systems across much of the continental United States.

  7. Atmospheric pressure plasma surface modification of titanium for high temperature adhesive bonding

    NARCIS (Netherlands)

    Akram, M.; Jansen, K.M.B.; Ernst, L.J.; Bhowmik, S.

    2011-01-01

    In this investigation surface treatment of titanium is carried out by plasma ion implantation under atmospheric pressure plasma in order to increase the adhesive bond strength. Prior to the plasma treatment, titanium surfaces were mechanically treated by sand blasting. It is observed that the contac

  8. Nitrogen and Carbon Dynamics Across Trophic Levels Along an Atmospheric Nitrogen Deposition Gradient

    Science.gov (United States)

    Wissinger, B. D.; Bell, M. D.; Newingham, B. A.

    2011-12-01

    Atmospheric nitrogen deposition has altered soil biogeochemical processes and plant communities across the United States. Prior investigations have demonstrated these alterations; however, little is known about the effects of elevated nitrogen on higher trophic levels. Building upon previous research that revealed an atmospheric nitrogen deposition gradient from the San Bernardino Mountains through Joshua Tree National Park in California, we investigated atmospheric nitrogen and its effects on soils, plants, and harvester ants. We measured nitrogen and carbon concentrations, along with carbon and nitrogen stable isotopes, across trophic levels at eighteen urban and unpopulated sites along the deposition gradient. Carbon and nitrogen attributes were determined in atmospheric nitric acid, soil, Larrea tridentata and Ambrosia dumosa leaves, seeds from selected plant species, and ants. We predicted carbon and nitrogen ratios and isotopes to change in areas with higher nitrogen deposition and vary along the deposition gradient. Nitrogen (p=0.02) and carbon (p=0.05) concentrations, as well as C:N ratios (p=<0.001), significantly differed in Messor pergandei individuals among sites; however, no correlation was found between these carbon and nitrogen attributes and the nitrogen deposition gradient (%N r2=0.02, %C r2=0.007, C:N r2=0.02). The δ15N and δ13C values of the ants, leaf tissues, and seeds measured across the gradient follow similar patterns with r2 values all below 0.20. Our results suggest the current and previous rates of nitrogen deposition in this area are not enough to modify nitrogen and carbon concentrations and isotope values. Compensatory nitrogen cycling processes in the soil may reduce the effects of increased nitrogen on plants and thus higher trophic levels. Nitrogen and carbon dynamics across trophic levels might change after longer ecosystem exposure to elevated nitrogen; however, other abiotic and biotic factors are likely driving current

  9. Functionalization of Hydrogen-free Diamond-like Carbon Films using Open-air Dielectric Barrier Discharge Atmospheric Plasma Treatments

    Energy Technology Data Exchange (ETDEWEB)

    Lawrence Berkeley National Laboratory, Berkeley, CA 94720, USA; Instituto de Materiales de Madrid, C.S.I.C., Cantoblanco, 28049 Madrid, Spain; Instituto de Quimica-Fisica" Rocasolano" C.S.I.C., 28006 Madrid, Spain; Mahasarakham University, Mahasarakham 44150, Thailand; CASTI, CNR-INFM Regional Laboratory, L' Aquila 67100, Italy; SUNY Upstate Medical University, Syracuse, NY 13210, USA; Endrino, Jose; Endrino, J. L.; Marco, J. F.; Poolcharuansin, P.; Phani, A.R.; Allen, M.; Albella, J. M.; Anders, A.

    2007-12-28

    A dielectric barrier discharge (DBD) technique has been employed to produce uniform atmospheric plasmas of He and N2 gas mixtures in open air in order to functionalize the surface of filtered-arc deposited hydrogen-free diamond-like carbon (DLC) films. XPS measurements were carried out on both untreated and He/N2 DBD plasma treated DLC surfaces. Chemical states of the C 1s and N 1s peaks were collected and used to characterize the surface bonds. Contact angle measurements were also used to record the short- and long-term variations in wettability of treated and untreated DLC. In addition, cell viability tests were performed to determine the influence of various He/N2 atmospheric plasma treatments on the attachment of osteoblast MC3T3 cells. Current evidence shows the feasibility of atmospheric plasmas in producing long-lasting variations in the surface bonding and surface energy of hydrogen-free DLC and consequently the potential for this technique in the functionalization of DLC coated devices.

  10. Historical atmospheric mercury emissions and depositions in North America compared to mercury accumulations in sedimentary records

    Science.gov (United States)

    Pirrone, Nicola; Allegrini, Ivo; Keeler, Gerald J.; Nriagu, Jerome O.; Rossmann, Ronald; Robbins, John A.

    Gold and silver production in North America (included United States, Canada and Mexico) released a large amount of mercury to the atmosphere until well into this century when mercury (Hg) amalgamation was replaced by cyanide concentration. Since then, emissions from industries have been the dominant anthropogenic sources of atmospheric Hg in North America as a whole. Past Hg emissions from gold and silver extractions in North America during the 1800s do not show a clear evidence of atmospheric deposition occurred at the coring sites considered in this study. Estimated atmospheric emissions of Hg in North America peaked in 1879 (at about 1708 t yr -1) and 1920 (at about 940 t yr -1), primarily due to Hg emissions from gold and silver mining. After the Great Economic Depression (1929) Hg emissions peaked again in the 1947 (274 t yr -1), in 1970 (325 t yr -1) and in 1989 (330 t yr -1) as result of increased Hg emissions from industrial sources, though improvements in the emissions control technology in United States and Canada have been substantial. Estimates of total atmospheric deposition fluxes of Hg to water and terrestrial receptors were in the range of 14.3-19.8 μg m -2 yr -1 in North America as a whole, and averaged 135 μg m -2 yr -1 (global background + local emissions) in the Great Lakes. These values were in good agreement with recent estimates reported in literature. The comparison of atmospheric Hg deposition fluxes with Hg accumulation rates in sediment cores suggests that atmospheric deposition was the major source of Hg entering the lakes system at coring sites, however, important contributions to Lake Ontario sediment cores sites from 1940 to 1970 were likely originated from local point sources (i.e. direct discharges).

  11. Mechanisms of selective antitumor action of cold atmospheric plasma

    Science.gov (United States)

    Graves, David; Bauer, Georg

    2016-09-01

    Transformed (precancerous) cells are known to be subject to elimination through intercellular RONS-dependent apoptosis-inducing signaling. It is a remarkable fact that the chemical species utilized by apoptosis induction in transformed cells are essentially identical to chemical species created by cold atmospheric plasma (CAP) in aqueous solutions. The association between CAP-induced biochemistry and natural cell anti-tumor mechanisms offers the opportunity to establish a rationale for the observed successes of CAP in selectively eliminating tumor cells in vitro and in vivo. In particular, 1O2 appears to act to selectively induce apoptosis in tumor cells, and can also result in self-perpetuating, cell-to-cell apoptotic signaling. Various CAP-generated liquid phase species can react to form 1O2, thus providing a hypothetical mechanism to explain how CAP can trigger therapeutic apoptosis in tumors. The analysis of model experiments performed with defined RONS in vitro implies that CAP-derived 1O2 induces the mechanism through which CAP acts selectively against cancer cells in vitro and tumors in vivo. This hypothesis needs to be tested experimentally in order to establish its validity.

  12. Contamination due to memory effects in filtered vacuum arc plasma deposition systems

    CERN Document Server

    Martins, D R; Verdonck, P; Brown, I G

    2002-01-01

    Thin film synthesis by filtered vacuum arc plasma deposition is a widely used technique with a number of important emerging technological applications. A characteristic feature of the method is that during the deposition process not only is the substrate coated by the plasma, but the plasma gun itself and the magnetic field coil and/or vacuum vessel section constituting the macroparticle filter are also coated to some extent. If then the plasma gun cathode is changed to a new element, there can be a contamination of the subsequent film deposition by sputtering from various parts of the system of the previous coating species. We have experimentally explored this effect and compared our results with theoretical estimates of sputtering from the SRIM (Stopping and Range of Ions in Matter) code. We find film contamination of order 10-4 - 10-3, and the memory of the prior history of the deposition hardware can be relatively long-lasting.

  13. Modification of optical and electrical properties of chemical bath deposited CdS using plasma treatments

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez, G. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon, C.P 66450 (Mexico); Krishnan, B. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon, C.P 66450 (Mexico); CIIDIT, Universidad Autonoma de Nuevo Leon, Apodaca, Nuevo Leon (Mexico); Avellaneda, D.; Castillo, G. Alan; Das Roy, T.K. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon, C.P 66450 (Mexico); Shaji, S., E-mail: sshajis@yahoo.com [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon, C.P 66450 (Mexico); CIIDIT, Universidad Autonoma de Nuevo Leon, Apodaca, Nuevo Leon (Mexico)

    2011-08-31

    Cadmium sulphide (CdS) is a well known n-type semiconductor that is widely used in solar cells. Here we report preparation and characterization of chemical bath deposited CdS thin films and modification of their optical and electrical properties using plasma treatments. CdS thin films were prepared from a chemical bath containing Cadmium chloride, Triethanolamine and Thiourea under various deposition conditions. Good quality thin films were obtained during deposition times of 5, 10 and 15 min. CdS thin films prepared for 10 min. were treated using a glow discharge plasma having nitrogen and argon carrier gases. The changes in morphology, optical and electrical properties of these plasma treated CdS thin films were analyzed in detail. The results obtained show that plasma treatment is an effective technique in modification of the optical and electrical properties of chemical bath deposited CdS thin films.

  14. Impact of acid atmosphere deposition on soils : field monitoring and aluminum chemistry

    NARCIS (Netherlands)

    Mulder, J.

    1988-01-01

    The effect of acid atmospheric deposition on concentrations and transfer of major solutes in acid, sandy soils was studied. Emphasis was given to mobilization and transport of potentially toxic aluminum. Data on solute concentrations and fluxes in meteoric water as well as soil solutions

  15. The Effects of Atmospheric Nitrogen Deposition on Terrestrial and Freshwater Biodiversity

    NARCIS (Netherlands)

    Baron, J.S.; Barber, M.; Adams, M.; Dobben, van H.F.

    2014-01-01

    This chapter reports the findings of a Working Group on how atmospheric nitrogen (N) deposition affects both terrestrial and freshwater biodiversity. Regional and global scale impacts on biodiversity are addressed, together with potential indicators. Key conclusions are that: the rates of loss in bi

  16. Relation between forest vegetation, atmospheric deposition and site conditions at regional and European scales

    NARCIS (Netherlands)

    Dobben, van H.F.; Vries, de W.

    2010-01-01

    Several monitoring programs have been set up to assess effects of atmospheric deposition on forest ecosystems. The aim of the present study was to evaluate effects on the understorey vegetation, based on the first round of a regional (the Netherlands) and a European forest monitoring program. A mult

  17. Atmospheric spatial atomic layer deposition of in-doped ZnO

    NARCIS (Netherlands)

    Illiberi, A.; Scherpenborg, R.; Roozeboom, F.; Poodt, P.

    2014-01-01

    Indium-doped zinc oxide (ZnO:In) has been grown by spatial atomic layer deposition at atmospheric pressure (spatial-ALD). Trimethyl indium (TMIn), diethyl zinc (DEZ) and deionized water have been used as In, Zn and O precursor, respectively. The metal content of the films is controlled in the range

  18. Impact of acid atmospheric deposition on soils: Field monitoring and aluminium chemistry.

    NARCIS (Netherlands)

    Mulder, J.

    1988-01-01

    The effect of acid atmospheric deposition on concentrations and transfer of major solutes in acid, sandy soils was studied. Emphasis was given to mobilization and transport of potentially toxic aluminum. Data on solute concentrations and fluxes in meteoric water as well as soil solutions were obtain

  19. Development of atmospheric pressure large area plasma jet for sterilisation and investigation of molecule and plasma interaction

    Science.gov (United States)

    Zerbe, Kristina; Iberler, Marcus; Jacoby, Joachim; Wagner, Christopher

    2016-09-01

    The intention of the project is the development and improvement of an atmospheric plasma jet based on various discharge forms (e.g. DBD, RF, micro-array) for sterilisation of biomedical equipment and investigation of biomolecules under the influence of plasma stress. The major objective is to design a plasma jet with a large area and an extended length. Due to the success on small scale plasma sterilisation the request of large area plasma has increased. Many applications of chemical disinfection in environmental and medical cleaning could thereby be complemented. Subsequently, the interaction between plasma and biomolecules should be investigated to improve plasma strerilisation. Special interest will be on non equilibrium plasma electrons affecting the chemical bindings of organic molecules.

  20. Atmospheric-Pressure Cold Plasmas Used to Embed Bioactive Compounds in Matrix Material for Active Packaging of Fruits and Vegetables

    Science.gov (United States)

    Fernandez, Sulmer; Pedrow, Patrick; Powers, Joseph; Pitts, Marvin

    2009-10-01

    Active thin film packaging is a technology with the potential to provide consumers with new fruit and vegetable products-if the film can be applied without deactivating bioactive compounds.Atmospheric pressure cold plasma (APCP) processing can be used to activate monomer with concomitant deposition of an organic plasma polymerized matrix material and to immobilize a bioactive compound all at or below room temperature.Aims of this work include: 1) immobilize an antimicrobial in the matrix; 2) determine if the antimicrobial retains its functionality and 3) optimize the reactor design.The plasma zone will be obtained by increasing the voltage on an electrode structure until the electric field in the feed material (argon + monomer) yields electron avalanches. Results will be described using Red Delicious apples.Prospective matrix precursors are vanillin and cinnamic acid.A prospective bioactive compound is benzoic acid.

  1. Effect of helium plasma gas flow rate on the properties of WC-12 wt.%Co coatings sprayed by atmospheric plasma

    Directory of Open Access Journals (Sweden)

    Mihailo R. Mrdak

    2014-06-01

    Full Text Available The cermet coatings of WC-12wt.%Co are extensively used to improve the wear resistance of a wide range of technical components. This paper analyses the influence of the plasma gas flow of helium on the microstructure and mechanical properties of WC-12wt.%Co coatings deposited by plasma spraying at atmospheric pressure (APS. In order to obtain homogeneous and denser coatings, three different flows of He ( 8 l/min., 16 l/min. and 32 l/min were used in the research. With the application of He, coatings achieved higher values of hardness due to less degradation of the primary WC carbides. The main goal was to deposit dense and homogeneous layers of WC-12wt.%Co coatings with improved wear resistance for different applications. The test results of the microstructure of the layers were evaluated under a light microscope. The analysis of the microstructure and the mechanical properties of the deposited layers was made in accordance with the standard of Pratt-Whitney. The morphology of the powder particles and the microstructure of the best coating was examined on the SEM (scanning electron microscope. The evaluation of the mechanical properties of the layers was done by applying the HV0.3 method for microhardness testing and by applying tensile testing to test the bond strength. The research has shown that the flow of He plasma gas significantly affects the microstructure, the mechanical properties and the structure of WC-12 wt.%Co coatings.

  2. Modeling hydrodynamic flows in plasma fluxes when depositing metal layer on the surface of catalyst converters

    Science.gov (United States)

    Chinakhov, D. A.; Sarychev, V. D.; Granovsky, A. Yu; Solodsky, S. A.; Nevsky, S. A.; Konovalov, S. V.

    2017-01-01

    Air pollution with harmful substances resulting from combustion of liquid hydrocarbons and emitted into atmosphere became one of the global environmental problems in the late 20th century. The systems of neutralization capable to reduce toxicity of exhaust gases several times are very important for making environmentally safer combustion products discharged into the atmosphere. As revealed in the literature review, one of the most promising purification procedures is neutralization of burnt gases by catalyst converter systems. The principal working element in the converter is a catalytic layer of metals deposited on ceramics, with thickness 20-60 micron and a well-developed micro-relief. The paper presents a thoroughly substantiated new procedure of deposing a nano-scale surface layer of metal-catalyst particles, furthering the utilization of catalysts on a new level. The paper provides description of mathematical models and computational researches into plasma fluxes under high-frequency impulse input delivered to electrode material, explorations of developing Kelvin-Helmholtz, Marangoni and magnetic hydrodynamic instabilities on the surface of liquid electrode metal droplet in the nano-scale range of wavelengths to obtain a flow of nano-meter particles of cathode material. The authors have outlined a physical and mathematical model of magnetic and hydrodynamic instability for the case of melt flowing on the boundary with the molten metal with the purpose to predict the interphase shape and mutual effect of formed plasma jet and liquid metal droplet on the electrode in the nano-scale range of wavelengths at high-frequency impact on the boundary “electrode-liquid layer”.

  3. The contribution of atmospheric deposition and forest harvesting to forest soil acidification in China since 1980

    Science.gov (United States)

    Zhu, Qichao; De Vries, Wim; Liu, Xuejun; Zeng, Mufan; Hao, Tianxiang; Du, Enzai; Zhang, Fusuo; Shen, Jianbo

    2016-12-01

    Soils below croplands and grasslands have acidified significantly in China since the 1980s in terms of pH decline in response to acid inputs caused by intensified fertilizer application and/or acid deposition. However, it is unclear what the rate is of pH decline of forest soils in China in response to enhanced acid deposition and wood production over the same period. We therefore gathered soil pH data from the Second National Soil Inventory of China and publications from the China National Knowledge Infrastructure (CNKI) database in 1981-1985 and 2006-2010, respectively, to evaluate the long-term change of pH values in forest soils. We found that soil pH decreased on average by 0.36 units in the period 1981-1985 to 2006-2010., with most serious pH decline occurring in southwest China (0.63 pH units). The soil type with the strongest pH decline was the semi-Luvisol (0.44 pH units). The decrease in pH was significantly correlated with the acid input induced by atmospheric deposition and forest harvesting. On average, the contribution of atmospheric deposition to the total acid input was estimated at 84% whereas element uptake (due to forest wood growth and harvest) contributed 16% only. Atmospheric deposition is thus the major driver for the significant forest soil acidification across China.

  4. Effect of characteristics of plasma plume on the diamond-like film deposition

    Institute of Scientific and Technical Information of China (English)

    姚东升; 刘晶儒; 俞昌旋; 王丽戈; 詹如娟

    2000-01-01

    Pulsed KrF lasers of two different durations (30 ns, 500 fs) are used to deposit DLCfilms. By optical emission spectroscopy and ion probe, the composite species of laser generated plas-ma plume are identified, the average kinetic energy of ions, the plume flux and their variation with laserenergy density, and the distance from the target are investigated. The relation of the properties of de-posited films with the plasma characteristics is studied.

  5. Low temperature plasma deposition of silicon thin films: From amorphous to crystalline

    OpenAIRE

    Roca i Cabarrocas, Pere; Cariou, Romain; Labrune, Martin

    2012-01-01

    International audience; We report on the epitaxial growth of crystalline silicon films on (100) oriented crystalline silicon substrates by standard plasma enhanced chemical vapor deposition at 175 °C. Such unexpected epitaxial growth is discussed in the context of deposition processes of silicon thin films, based on silicon radicals and nanocrystals. Our results are supported by previous studies on plasma synthesis of silicon nanocrystals and point toward silicon nanocrystals being the most p...

  6. Biomagnetic monitoring of heavy metals contamination in deposited atmospheric dust, a case study from Isfahan, Iran.

    Science.gov (United States)

    Norouzi, Samira; Khademi, Hossein; Cano, Angel Faz; Acosta, Jose A

    2016-05-15

    Tree leaves are considered as one of the best biogenic dust collectors due to their ability to trap and retain particulate matter on their surfaces. In this study, the magnetic susceptibility (MS) and the concentration of selected heavy metals of plane tree (Platanus orientalis L.) leaves and deposited atmospheric dust, sampled by an indirect and a direct method, respectively, were determined to investigate the relationships between leaf magnetic parameters and the concentration of heavy metals in deposited atmospheric dust. The objective was to develop a biomagnetic method as an alternative to the common ones used for determining atmospheric heavy metal contaminations. Plane tree leaves were monthly sampled on the 19th of May to November, 2012 (T1-T7), for seven months from 21 different sites in the city of Isfahan, central Iran. Deposited atmospheric dust samples were also collected using flat glass surfaces from the same sites on the same dates, except for T1. MS (χlf, χhf) values in washed (WL) and unwashed leaves (UL) as well as Cu, Fe, Mn, Ni, Pb, and Zn concentrations in UL and deposited atmospheric dust samples were determined. The results showed that the MS content with a biogenic source was low with almost no significant change during the sampling period, while an increasing trend was observed in the MS content of UL samples due to the deposition of heavy metals and magnetic particles on leaf surfaces throughout the plant growth. The latter type of MS content could be reduced through washing off by rain. Most heavy metals examined, as well as the Tomlinson pollution load index (PLI) in UL, showed statistically significant correlations with MS values. The correlation between heavy metals content in atmospheric dust deposited on glass surfaces and leaf MS values was significant for Cu, Fe, Pb, and Zn. Moreover, the similarity observed between the spatial distribution maps of leaf MS and deposited atmospheric dust PLI provided convincing evidence regarding

  7. Comparison of Mercury Mass Loading in Streams to Wet and Dry Atmospheric Deposition in Watersheds of the Western US: Evidence for Non-Atmospheric Mercury Sources

    Science.gov (United States)

    Domagalski, J. L.; Majewski, M. S.; Alpers, C. N.; Eckley, C.

    2015-12-01

    Many streams in the western United States (US) are listed as impaired by mercury (Hg), and it is important to understand the magnitudes of the various sources in order to implement management strategies. Atmospheric deposition of Hg and can be a major source of aquatic contamination, along with mine wastes, and other sources. Prior studies in the eastern US have shown that streams deliver less than 50% of the atmospherically deposited Hg on an annual basis. In this study, we compared annual stream Hg loads for 20 watersheds in the western US to measured wet and modeled dry deposition. Land use varies from undisturbed to mixed (agricultural, urban, forested, mining). Data from the Mercury Deposition Network was used to estimate Hg input from precipitation. Dry deposition was not directly measured, but can be modeled using the Community Multi-scale Air Quality model. At an undeveloped watershed in the Rocky Mountains, the ratio of stream Hg load to atmospheric deposition was 0.2 during a year of average precipitation. In contrast, at the Carson River in Nevada, with known Hg contamination from historical silver mining with Hg amalgamation, stream export exceeded atmospheric deposition by a factor of 60, and at a small Sierran watershed with gold mining, the ratio was 70. Larger watersheds with mixed land uses, tend to have lower ratios of stream export relative to atmospheric deposition suggesting storage of Hg. The Sacramento River was the largest watershed for which Hg riverine loads were available with an average ratio of stream Hg export to atmospheric deposition of 0.10. Although Hg was used in upstream historical mining operations, the downstream river Hg load is partially mitigated by reservoirs, which trap sediment. This study represents the first compilation of riverine Hg loads in comparison to atmospheric deposition on a regional scale; the approach may be useful in assessing the relative importance of atmospheric and non-atmospheric Hg sources.

  8. The Role of Plasma in Plasma Enhanced Chemical Vapour Deposition of Nanostructure Growth

    Science.gov (United States)

    Hash, David B.; Meyyappan, M.; Teo, Kenneth B. K.; Lacerda, Rodrigo G.; Rupesinghe, Nalin L.

    2004-01-01

    Chemical vapour deposition (CVD) has become the preferred process for high yield growth of carbon nanotubes and nanofibres because of its ability to pattern growth through lithographic positioning of transition metal catalysts on substrates. Many potential applications of nanotubes such as field emitters [1] require not only patterned growth but also vertical alignment. Some degree of ali,ment in thermal CVD processes can be obtained when carbon nanotubes are grown closely together as a result of van der Waals interactions. The ali,onment however is marginal, and the van der Waals prerequisite makes growth of freestanding nanofibres with thermal CVD unrealizable. The application of electric fields as a means of ali,onment has been shown to overcome this limitation [2-5], and highly aligned nanostructures can be grown if electric fields on the order of 0.5 V/microns are employed. Plasma enhanced CVD in various configurations including dc, rf, microwave, inductive and electron cyclotron resonance has been pursued as a means of enabling alignment in the CVD process. However, the sheath fields for the non-dc sources are in general not sufficient for a high degree of ali,pment and an additional dc bias is usually applied to the growth substrate. This begs the question as to the actual role of the plasma. It is clear that the plasma itself is not required for aligned growth as references [3] and [4] employed fields through small applied voltages (3-20 V) across very small electrode spacings (10-100 microns) and thus avoided striking a discharge.

  9. Atmospheric trace elements at Enewetak Atoll: 2. Transport to the ocean by wet and dry deposition

    Science.gov (United States)

    Arimoto, R.; Duce, R. A.; Ray, B. J.; Unni, C. K.

    1985-02-01

    The concentrations of trace elements in precipitation and dry deposition are presented for samples collected at Enewetak Atoll (11°N, 162° E) during SEAREX experiments in 1979. The concentrations of Al, Sc, Mn, Fe, Co, and Th in rain are dominated by crustal material, and for these elements, wet deposition evidently exceeds dry deposition. For most of these elements the present rates of atmospheric deposition at Enewetak are similar to their mean rate of accumulation in sediments over the past 5-10,000 years, suggesting that the air-to-sea exchange of particles is closely tied to the sedimentary cycle of the mid-Pacific. Noncrustal sources govern the concentrations of Pb, Zn, Cu, Se, and Cd in wet and dry deposition samples. Analyses of dry deposition collected from a flat plastic plate indicate that the amount of material recycled from the sea surface varies markedly between samples, and even though these estimates do not necessarily reflect the dry deposition to the ocean surface, the results suggest that recycled sea spray often amounts to more than 50% of the total dry deposition of the enriched elements. Recycled sea spray also makes up a significant fraction of the total wet deposition of the enriched elements. The net deposition rates of elements such as Cu and Zn are greater than or equal to their inputs from vertical mixing, but the net deposition of Pb clearly exceeds the input from upwelling. The current net deposition rates of the enriched elements are also similar to their rates of removal to sediments. These results indicate that air-sea exchange processes may significantly affect the chemistry of trace metals in the open ocean.

  10. Influence of the voltage waveform during nanocomposite layer deposition by aerosol-assisted atmospheric pressure Townsend discharge

    Energy Technology Data Exchange (ETDEWEB)

    Profili, J. [LAPLACE, Université de Toulouse, CNRS, INPT, UPS, Toulouse (France); Département de Physique, Université de Montréal, Montréal, Québec H3C 3J7 (Canada); Levasseur, O.; Stafford, L. [Département de Physique, Université de Montréal, Montréal, Québec H3C 3J7 (Canada); Naudé, N.; Gherardi, N., E-mail: nicolas.gherardi@laplace.univ-tlse.fr [LAPLACE, Université de Toulouse, CNRS, INPT, UPS, Toulouse (France); Chaneac, C. [Sorbonne Universités, UPMC Univ. Paris 06, CNRS, Collège de France, Laboratoire de Chimie de la Matière Condensée de Paris (CMCP), 4 place Jussieu, F-75005 Paris (France)

    2016-08-07

    This work examines the growth dynamics of TiO{sub 2}-SiO{sub 2} nanocomposite coatings in plane-to-plane Dielectric Barrier Discharges (DBDs) at atmospheric pressure operated in a Townsend regime using nebulized TiO{sub 2} colloidal suspension in hexamethyldisiloxane as the growth precursors. For low-frequency (LF) sinusoidal voltages applied to the DBD cell, with voltage amplitudes lower than the one required for discharge breakdown, Scanning Electron Microscopy of silicon substrates placed on the bottom DBD electrode reveals significant deposition of TiO{sub 2} nanoparticles (NPs) close to the discharge entrance. On the other hand, at higher frequencies (HF), the number of TiO{sub 2} NPs deposited strongly decreases due to their “trapping” in the oscillating voltage and their transport along the gas flow lines. Based on these findings, a combined LF-HF voltage waveform is proposed and used to achieve significant and spatially uniform deposition of TiO{sub 2} NPs across the whole substrate surface. For higher voltage amplitudes, in the presence of hexamethyldisiloxane and nitrous oxide for plasma-enhanced chemical vapor deposition of inorganic layers, it is found that TiO{sub 2} NPs become fully embedded into a silica-like matrix. Similar Raman spectra are obtained for as-prepared TiO{sub 2} NPs and for nanocomposite TiO{sub 2}-SiO{sub 2} coating, suggesting that plasma exposure does not significantly alter the crystalline structure of the TiO{sub 2} NPs injected into the discharge.

  11. Combined effects of iron and copper from atmospheric dry deposition on ocean productivity

    Science.gov (United States)

    Wang, F. J.; Chen, Y.; Guo, Z. G.; Gao, H. W.; Mackey, K. R.; Yao, X. H.; Zhuang, G. S.; Paytan, A.

    2017-03-01

    Atmospheric deposition can provide nutrients and potential toxicants to marine ecosystem, hence affecting ocean net primary productivity (NPP). Nonetheless, the interactive effects of mixed aerosol components on phytoplankton have rarely been reported. Here we explored the combined effects of iron (Fe) and copper (Cu) on NPP over the East China Sea. In aerosol addition mesocosm experiments, phytoplankton growth was suppressed under high aerosol Cu but was increased when high Cu was accompanied by high Fe in aerosols. A time series of soluble aerosol Fe and Cu deposition was obtained and compared to regional chlorophyll a (Chl a) abundances from Moderate Resolution Imaging Spectroradiometer/Aqua. Strong positive correlations were observed between the dry flux ratios of soluble Fe/Cu and Chl a abundances in the large offshore area, whereas these variables were uncoupled in coastal regions where riverine input and upwelling dominated the biogeochemistry. Current work provides insight into the complex linkage between atmospheric deposition and marine productivity.

  12. Atomic Layer Deposition Al2O3 Thin Films in Magnetized Radio Frequency Plasma Source

    Science.gov (United States)

    Li, Xingcun; Chen, Qiang; Sang, Lijun; Yang, Lizhen; Liu, Zhongwei; Wang, Zhenduo

    Self-limiting deposition of aluminum oxide (Al2O3) thin films were accomplished by the plasma-enhanced chemical vapor deposition using trimethyl aluminum (TMA) and O2 as precursor and oxidant, respectively, where argon was kept flowing in whole deposition process as discharge and purge gas. In here we present a novel plasma source for the atomic layer deposition technology, magnetized radio frequency (RF) plasma. Difference from the commercial RF source, magnetic coils were amounted above the RF electrode, and the influence of the magnetic field strength on the deposition rate and morphology are investigated in detail. It concludes that a more than 3 Å/ purging cycle deposition rate and the good quality of ALD Al2O3 were achieved in this plasma source even without extra heating. The ultra-thin films were characterized by including Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectric spectroscopy (XPS), scanning electron microscopy (SEM), and atomic force microscopy (AFM). The high deposition rates obtained at ambient temperatures were analyzed after in-situ the diagnostic of plasmas by Langmuir probe.

  13. Mosses as an integrating tool for monitoring PAH atmospheric deposition: comparison with total deposition and evaluation of bioconcentration factors. A year-long case-study.

    Science.gov (United States)

    Foan, Louise; Domercq, Maria; Bermejo, Raúl; Santamaría, Jesús Miguel; Simon, Valérie

    2015-01-01

    Polycyclic aromatic hydrocarbon (PAH) atmospheric deposition was evaluated at a remote site in Northern Spain using moss biomonitoring with Hylocomium splendens (Hedw.) Schimp., and by measuring the total deposition fluxes of PAHs. The year-long study allowed seasonal variations of PAH content in mosses to be observed, and these followed a similar trend to those of PAH fluxes in total deposition. Generally, atmospheric deposition of PAHs is greater in winter than in summer, due to more PAH emissions from domestic heating, less photoreactivity of the compounds, and intense leaching of the atmosphere by wet deposition. However, fractionation of these molecules between the environmental compartments occurs: PAH fluxes in total deposition and PAH concentrations in mosses are correlated with their solubility (r=0.852, pPAH fluxes can be estimated with moss biomonitoring data if the bioconcentration or 'enriching' factors are known.

  14. Effect of impurity deposition layer formation on D retention in LHD plasma exposed W

    Directory of Open Access Journals (Sweden)

    Y. Oya

    2016-12-01

    Full Text Available Effect of carbon based mixed-material deposition layer formation on hydrogen isotope retention was studied. The tungsten (W samples were placed at four different positions, namely PI (sputtering erosion dominated area, DP (deposition dominated area, HL (higher heat load area, and ER (erosion dominated area during 2013 plasma experimental campaign in Large Helical Device (LHD at National Institute for Fusion Science (NIFS, Japan and were exposed to ∼ 4000 shots of hydrogen plasma in a 2013 plasma experimental campaign. Most of the sample surface except for ER was covered by a mixed-material deposition layer formed by plasma experimental campaign, which consisted of carbon, but some metal impurities were contained. For ER sample, He bubbles were formed due to long term He discharge cleaning and He plasma experiments during the plasma experimental campaign. The additional 1keV D2+ implantation was performed to evaluated the D retention enhancement by plasma exposure. It was found that both of H and D retentions were clearly increased. In particular, the H retention was controlled by the thickness of the carbon-dominated mixed-material deposition layer, indicating most of the H was trapped by this mixed-material deposition layer. It is concluded that the accumulation of low-Z mixed-material layer on the surface of the first wall is one of key issues for the determination of hydrogen isotope retention in first wall.

  15. High power impulse magnetron sputtering and related discharges: scalable plasma sources for plasma-based ion implantation and deposition

    Energy Technology Data Exchange (ETDEWEB)

    Anders, Andre

    2009-09-01

    High power impulse magnetron sputtering (HIPIMS) and related self-sputtering techniques are reviewed from a viewpoint of plasma-based ion implantation and deposition (PBII&D). HIPIMS combines the classical, scalable sputtering technology with pulsed power, which is an elegant way of ionizing the sputtered atoms. Related approaches, such as sustained self-sputtering, are also considered. The resulting intense flux of ions to the substrate consists of a mixture of metal and gas ions when using a process gas, or of metal ions only when using `gasless? or pure self-sputtering. In many respects, processing with HIPIMS plasmas is similar to processing with filtered cathodic arc plasmas, though the former is easier to scale to large areas. Both ion implantation and etching (high bias voltage, without deposition) and thin film deposition (low bias, or bias of low duty cycle) have been demonstrated.

  16. Assessment of dry and wet atmospheric deposits of radioactive aerosols: application to Fukushima radiocaesium fallout.

    Science.gov (United States)

    Gonze, Marc-André; Renaud, Philippe; Korsakissok, Irène; Kato, Hiroaki; Hinton, Thomas G; Mourlon, Christophe; Simon-Cornu, Marie

    2014-10-07

    The Fukushima Dai-ichi nuclear accident led to massive atmospheric deposition of radioactive substances onto the land surfaces. The spatial distribution of deposits has been estimated by Japanese authorities for gamma-emitting radionuclides through either airborne monitoring surveys (since April 2011) or in situ gamma-ray spectrometry of bare soil areas (since summer 2011). We demonstrate that significant differences exist between the two surveys for radiocaesium isotopes and that these differences can be related to dry deposits through the use of physically based relationships involving aerosol deposition velocities. The methodology, which has been applied to cesium-134 and cesium-137 deposits within 80-km of the nuclear site, provides reasonable spatial estimations of dry and wet deposits that are discussed and compared to atmospheric numerical simulations from the Japanese Atomic Energy Agency and the French Institute of Radioprotection and Nuclear Safety. As a complementary approach to numerical simulations, this field-based analysis has the possibility to contribute information that can be applied to the understanding and assessment of dose impacts to human populations and the environment around Fukushima.

  17. Atmospheric deposition patterns of (210)Pb and (7)Be in Cienfuegos, Cuba.

    Science.gov (United States)

    Alonso-Hernández, Carlos M; Morera-Gómez, Yasser; Cartas-Águila, Héctor; Guillén-Arruebarrena, Aniel

    2014-12-01

    The radiometric composition of bulk deposition samples, collected monthly for one year, February 2010 until January 2011, at a site located in Cienfuegos (22° 03' N, 80° 29' W) (Cuba), are analysed in this paper. Measurement of (7)Be and (210)Pb activity concentrations were carried out in 12 bulk deposition samples. The atmospheric deposition fluxes of (7)Be and (210)Pb are in the range of 13.2-132 and 1.24-8.29 Bq m(-2), and their mean values are: 56.6 and 3.97 Bq m(-2), respectively. The time variations of the different radionuclide have been discussed in relation with meteorological factors and the mean values have been compared to those published in recent literature from other sites located at different latitudes. The annual average flux of (210)Pb and (7)Be were 47 and 700 Bq m(-2) y(-1), respectively. Observed seasonal variations of deposition data are explained in terms of different environmental features. The atmospheric deposition fluxes of (7)Be and (210)Pb were moderately well correlated with precipitation and well correlated with one another. The (210)Pb/(7)Be ratios in the monthly depositions samples varied in the range of 0.05-0.10 and showed a strong correlation with the number of rainy days.

  18. Development and Implementation of Critical Loads for Atmospheric Deposition: Federal Land Management Implications

    Science.gov (United States)

    Porter, E. M.

    2004-12-01

    Critical loads for atmospheric deposition have been widely developed and used in Europe, Canada, and other countries. Critical loads are used to influence air pollution emissions reductions, thereby protecting and restoring aquatic and terrestrial ecosystems. In the United States, federal land management agencies are adopting the critical load concept as a potentially valuable resource management tool. Certain parks and wilderness areas are currently being affected by anthropogenic nitrogen and sulfur deposition. Effects of excess deposition include acidification, nitrogen enrichment, toxicity, and changes in biotic communities. Streams in both Shenandoah and Great Smoky Mountains National Parks are experiencing chronic and episodic acidification and brook trout fisheries in Shenandoah have been affected. High elevation ecosystems in Rocky Mountain National Park are undergoing subtle changes in aquatic and terrestrial ecosystems attributable to atmospheric deposition. Natural resources in many other federal areas have been affected or are at risk from deposition. Federal land managers are refining strategies for critical loads that include working with scientists to identify resources sensitive to deposition, defining resource protection criteria that will meet management objectives, and estimating and implementing critical loads. Critical loads will be used in resource management decisions and federal land management planning. They will be used to evaluate management actions and assess progress towards meeting management goals. Federal land managers will also communicate critical loads information to air pollution regulatory agencies to inform emissions management strategies for clean air.

  19. Atmospheric deposition of nitrogen to the Baltic Sea in the period 1995–2006

    Directory of Open Access Journals (Sweden)

    J. Bartnicki

    2011-10-01

    Full Text Available The EMEP/MSC-W model has been used to compute atmospheric nitrogen deposition into the Baltic Sea basin for the period of 12 yr: 1995–2006. The level of annual total nitrogen deposition into the Baltic Sea basin has changed from 230 Gg N in 1995 to 199 Gg N in 2006, decreasing 13 %. This value corresponds well with the total nitrogen emission reduction (11 % in the HELCOM Contracting Parties. However, inter-annual variability of nitrogen deposition to the Baltic Sea basin is relatively large, ranging from −13 % to +17 % of the averaged value. It is mainly caused by the changing meteorological conditions and especially precipitation in the considered period. The calculated monthly deposition pattern is similar for most of the years showing maxima in the autumn months October and November. The source allocation budget for atmospheric nitrogen deposition to the Baltic Sea basin was calculated for each year of the period 1997–2006. The main emission sources contributing to total nitrogen deposition are: Germany 18–22 %, Poland 11–13 % and Denmark 8–11 %. There is also a significant contribution from distant sources like the United Kingdom 6–9 %, as well as from the international ship traffic on the Baltic Sea 4–5 %.

  20. Hydroxyapatite coatings deposited by liquid precursor plasma spraying: controlled dense and porous microstructures and osteoblastic cell responses

    Energy Technology Data Exchange (ETDEWEB)

    Huang Yi; Song Lei; Liu Xiaoguang; Xiao Yanfeng; Wu Yao; Chen Jiyong; Wu Fang; Gu Zhongwei, E-mail: fangwu0808@yahoo.co, E-mail: fwu@scu.edu.c [National Engineering Research Center for Biomaterials, Sichuan University, Chengdu 610064 (China)

    2010-12-15

    Hydroxyapatite coatings were deposited on Ti-6Al-4V substrates by a novel plasma spraying process, the liquid precursor plasma spraying (LPPS) process. X-ray diffraction results showed that the coatings obtained by the LPPS process were mainly composed of hydroxyapatite. The LPPS process also showed excellent control on the coating microstructure, and both nearly fully dense and highly porous hydroxyapatite coatings were obtained by simply adjusting the solid content of the hydroxyapatite liquid precursor. Scanning electron microscope observations indicated that the porous hydroxyapatite coatings had pore size in the range of 10-200 {mu}m and an average porosity of 48.26 {+-} 0.10%. The osteoblastic cell responses to the dense and porous hydroxyapatite coatings were evaluated with human osteoblastic cell MG-63, in respect of the cell morphology, proliferation and differentiation, with the hydroxyapatite coatings deposited by the atmospheric plasma spraying (APS) process as control. The cell experiment results indicated that the heat-treated LPPS coatings with a porous structure showed the best cell proliferation and differentiation among all the hydroxyapatite coatings. Our results suggest that the LPPS process is a promising plasma spraying technique for fabricating hydroxyapatite coatings with a controllable microstructure, which has great potential in bone repair and replacement applications.

  1. Supersonic Plasma Spray Deposition of CoNiCrAlY Coatings on Ti-6Al-4V Alloy

    Science.gov (United States)

    Caliari, F. R.; Miranda, F. S.; Reis, D. A. P.; Essiptchouk, A. M.; Filho, G. P.

    2017-06-01

    Plasma spray is a versatile technology used for production of environmental and thermal barrier coatings, mainly in the aerospace, gas turbine, and automotive industries, with potential application in the renewable energy industry. New plasma spray technologies have been developed recently to produce high-quality coatings as an alternative to the costly low-pressure plasma-spray process. In this work, we studied the properties of as-sprayed CoNiCrAlY coatings deposited on Ti-6Al-4V substrate with smooth surface ( R a = 0.8 μm) by means of a plasma torch operating in supersonic regime at atmospheric pressure. The CoNiCrAlY coatings were evaluated in terms of their surface roughness, microstructure, instrumented indentation, and phase content. Static and dynamic depositions were investigated to examine their effect on coating characteristics. Results show that the substrate surface velocity has a major influence on the coating properties. The sprayed CoNiCrAlY coatings exhibit low roughness ( R a of 5.7 μm), low porosity (0.8%), excellent mechanical properties ( H it = 6.1 GPa, E it = 155 GPa), and elevated interface toughness (2.4 MPa m1/2).

  2. Nitrogen concentrations in mosses indicate the spatial distribution of atmospheric nitrogen deposition in Europe

    Energy Technology Data Exchange (ETDEWEB)

    Harmens, H., E-mail: hh@ceh.ac.uk [Centre for Ecology and Hydrology, Environment Centre Wales, Deiniol Road, Bangor, Gwynedd LL57 2UW (United Kingdom); Norris, D.A., E-mail: danor@ceh.ac.uk [Centre for Ecology and Hydrology, Environment Centre Wales, Deiniol Road, Bangor, Gwynedd LL57 2UW (United Kingdom); Cooper, D.M., E-mail: cooper@ceh.ac.uk [Centre for Ecology and Hydrology, Environment Centre Wales, Deiniol Road, Bangor, Gwynedd LL57 2UW (United Kingdom); Mills, G., E-mail: gmi@ceh.ac.uk [Centre for Ecology and Hydrology, Environment Centre Wales, Deiniol Road, Bangor, Gwynedd LL57 2UW (United Kingdom); Steinnes, E., E-mail: Eiliv.Steinnes@chem.ntnu.no [Department of Chemistry, Norwegian University of Science and Technology, 7491 Trondheim (Norway); Kubin, E., E-mail: Eero.Kubin@metla.fi [Finnish Forest Research Institute, Kirkkosaarentie 7, 91500 Muhos (Finland); Thoeni, L., E-mail: lotti.thoeni@fub-ag.ch [FUB-Research Group for Environmental Monitoring, Alte Jonastrasse 83, 8640 Rapperswil (Switzerland); Aboal, J.R., E-mail: jesusramon.aboal@usc.es [University of Santiago de Compostela, Faculty of Biology, Department of Ecology, 15782 Santiago de Compostela (Spain); Alber, R., E-mail: Renate.Alber@provinz.bz.it [Environmental Agency of Bolzano, 39055 Laives (Italy); Carballeira, A., E-mail: alejo.carballeira@usc.es [University of Santiago de Compostela, Faculty of Biology, Department of Ecology, 15782 Santiago de Compostela (Spain); Coskun, M., E-mail: coskunafm@yahoo.com [Canakkale Onsekiz Mart University, Faculty of Medicine, Department of Medical Biology, 17100 Canakkale (Turkey); De Temmerman, L., E-mail: ludet@var.fgov.be [Veterinary and Agrochemical Research Centre, Tervuren (Belgium); Frolova, M., E-mail: marina.frolova@lvgma.gov.lv [Latvian Environment, Geology and Meteorology Agency, Riga (Latvia); Gonzalez-Miqueo, L., E-mail: lgonzale2@alumni.unav.es [Univ. of Navarra, Irunlarrea No 1, 31008 Pamplona (Spain)

    2011-10-15

    In 2005/6, nearly 3000 moss samples from (semi-)natural location across 16 European countries were collected for nitrogen analysis. The lowest total nitrogen concentrations in mosses (<0.8%) were observed in northern Finland and northern UK. The highest concentrations ({>=}1.6%) were found in parts of Belgium, France, Germany, Slovakia, Slovenia and Bulgaria. The asymptotic relationship between the nitrogen concentrations in mosses and EMEP modelled nitrogen deposition (averaged per 50 km x 50 km grid) across Europe showed less scatter when there were at least five moss sampling sites per grid. Factors potentially contributing to the scatter are discussed. In Switzerland, a strong (r{sup 2} = 0.91) linear relationship was found between the total nitrogen concentration in mosses and measured site-specific bulk nitrogen deposition rates. The total nitrogen concentrations in mosses complement deposition measurements, helping to identify areas in Europe at risk from high nitrogen deposition at a high spatial resolution. - Highlights: > Nitrogen concentrations in mosses were determined at ca. 3000 sites across Europe. > Moss concentrations were compared with EMEP modelled nitrogen deposition. > The asymptotic relationship for Europe showed saturation at ca. 15 kg N ha{sup -1} y{sup -1}. > Linear relationships were found with measured nitrogen deposition in some countries. > Moss concentrations complement deposition measurements at high spatial resolution. - Mosses as biomonitors of atmospheric nitrogen deposition in Europe.

  3. Deactivation of Enterococcus Faecalis Bacteria by an Atmospheric Cold Plasma Brush

    Science.gov (United States)

    Chen, Wei; Huang, Jun; Du, Ning; Liu, Xiao-Di; Lv, Guo-Hua; Wang, Xing-Quan; Zhang, Guo-Ping; Guo, Li-Hong; Yang, Si-Ze

    2012-07-01

    An atmospheric cold plasma brush suitable for large area and low-temperature plasma-based sterilization is designed and used to treat enterococcus faecalis bacteria. The results show that the efficiency of the inactivation process by helium plasma is dependent on applied power and exposure time. After plasma treatments, the cell structure and morphology changes can be observed by scanning electron microscopy. Optical emission measurements indicate that reactive species such as O and OH play a significant role in the sterilization process.

  4. Properties of Atmospheric Pressure Ar Plasma Jet Depending on Treated Dielectric Material

    Science.gov (United States)

    Prysiazhnyi, Vadym; Ricci Castro, Alonso H.; Kostov, Konstantin G.

    2017-02-01

    Atmospheric pressure plasma jet operated in argon was utilized to modify surfaces of glass, acrylic, and PTFE dielectrics. This paper describes the influence of the dielectric substrate on operation and properties of plasma. Two modes of operation (each of those have two patterns) were described. The transition from one mode to another, values of the dissipated power, and spreading of plasma over the dielectric surfaces strongly depended on the substrate material. Additionally, three methods of plasma spreading estimation were presented and discussed.

  5. Expanding thermal plasma chemical vapour deposition of ZnO:Al layers for CIGS solar cells

    NARCIS (Netherlands)

    Sharma, K.; Williams, B.L.; Mittal, A.; Knoops, H.C.M.; Kniknie, B.J.; Bakker, N.J.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

    2014-01-01

    Aluminium-doped zinc oxide (ZnO:Al) grown by expanding thermal plasma chemical vapour deposition (ETP-CVD) has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing ZnO

  6. Expanding thermal plasma chemical vapour deposition of ZnO:Al layers for CIGS solar cells

    NARCIS (Netherlands)

    Sharma, K.; Williams, B.L.; Mittal, A.; Knoops, H.C.M.; Kniknie, B.J.; Bakker, N.J.; Kessels, W.M.M.; Schropp, R.E.I.; Creatore, M.

    2014-01-01

    Aluminium-doped zinc oxide (ZnO:Al) grown by expanding thermal plasma chemical vapour deposition (ETP-CVD) has demonstrated excellent electrical and optical properties, which make it an attractive candidate as a transparent conductive oxide for photovoltaic applications. However, when depositing ZnO

  7. Surface modification by plasma polymerization: film deposition, tailoring of surface properties and biocompatibility

    NARCIS (Netherlands)

    Os, van Menno Thomas

    2000-01-01

    The work described in this thesis concerns the surface modification of materials by thin film deposition in a plasma reactor. In particular, thin polymeric films bearing amine functionalities were synthesized by plasma polymerization of amino group containing monomers. In addition to the synthesis,

  8. Electrical properties of plasma-deposited silicon oxide clarified by chemical modeling

    NARCIS (Netherlands)

    Kovalgin, A.Y.; Boogaard, A.; Brunets, I.; Aarnink, A.A.I.; Wolters, R.A.M.

    2009-01-01

    Our study is focused on Plasma Enhanced Chemical Vapor Deposition (PECVD) of silicon dioxide films at low temperatures (< 150 oC) using Inductively Coupled (IC) High-Density (HD) plasma source. We recently fabricated Thin Film Transistors (TFTs) with high-quality ICPECVD gate oxides, which exhibited

  9. A mathematical model and simulation results of plasma enhanced chemical vapor deposition of silicon nitride films

    NARCIS (Netherlands)

    Konakov, S.A.; Krzhizhanovskaya, V.V.

    2015-01-01

    We developed a mathematical model of Plasma Enhanced Chemical Vapor Deposition (PECVD) of silicon nitride thin films from SiH4-NH3-N2-Ar mixture, an important application in modern materials science. Our multiphysics model describes gas dynamics, chemical physics, plasma physics and electrodynamics.

  10. Atmospheric wet deposition of sulfur and nitrogen in Jiuzhaigou National Nature Reserve, Sichuan Province, China.

    Science.gov (United States)

    Qiao, Xue; Xiao, Weiyang; Jaffe, Daniel; Kota, Sri Harsha; Ying, Qi; Tang, Ya

    2015-04-01

    In the last two decades, remarkable ecological changes have been observed in Jiuzhaigou National Nature Reserve (JNNR). Some of these changes might be related to excessive deposition of sulfur (S) and nitrogen (N), but the relationship has not been quantified due to lack of monitoring data, particularly S and N deposition data. In this study, we investigated the concentrations, fluxes, and sources of S and N wet deposition in JNNR from April 2010 to May 2011. The results show that SO4(2-), NO3-, and NH4+ concentrations in the wet deposition were 39.4-170.5, 6.2-34.8, and 0.2-61.2 μeq L(-1), with annual Volume-Weighted Mean (VWM) concentrations of 70.5, 12.7, and 13.4 μeq L(-1), respectively. Annual wet deposition fluxes of SO4(2-), NO3-, and NH4+ were 8.06, 1.29, and 1.39 kg S(N)ha(-1), respectively, accounting for about 90% of annual atmospheric inputs of these species at the monitoring site. The results of Positive Matrix Factorization (PMF) analysis show that fossil fuel combustion, agriculture, and aged sea salt contributed to 99% and 83% of annual wet deposition fluxes of SO4(2-) and NO3-, respectively. Agriculture alone contributed to 89% of annual wet deposition flux of NH4+. Although wet deposition in JNNR was polluted by anthropogenic acids, the acidity was largely neutralized by the Ca2+ from crust and 81% of wet deposition samples had a pH higher than 6.00. However, acid rain mainly caused by SO4(2-) continued to occur in the wet season, when ambient alkaline dust concentration was lower. Since anthropogenic emissions have elevated S and N deposition and caused acid rain in JNNR, further studies are needed to better quantify the regional sources and ecological effects of S and N deposition for JNNR.

  11. The characteristics of arc beam shaping in hybrid plasma and laser deposition manufacturing

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Hai'ou; QIAN; Yingping; WANG; Guilan; ZHENG; Qiguang

    2006-01-01

    As a new direct metal prototyping technology,the hybrid plasma and laser deposition manufacturing (PLDM) is proposed in this paper. In order to figure out the characteristics of plasma arc beam and mould in the PLDM process of high temperature alloy, the high speed CCD camera is used to obtain the picture around the plasma arc. Afterwards the sketch of picture is clearly obtained. And the effect of laser parameter, such as average power, pulse width, pulse repetition frequency and the angle between laser beam and plasma arc beam on the plasma arc appearance, is studied experimentally. The results show that the modality of plasma arc beam is markedly influenced by laser beam. And the improvements of shape precision and surface state of the layer deposited by PLDM are confirmed.

  12. Non-thermal atmospheric pressure plasma activates lactate in Ringer's solution for anti-tumor effects.

    Science.gov (United States)

    Tanaka, Hiromasa; Nakamura, Kae; Mizuno, Masaaki; Ishikawa, Kenji; Takeda, Keigo; Kajiyama, Hiroaki; Utsumi, Fumi; Kikkawa, Fumitaka; Hori, Masaru

    2016-11-08

    Non-thermal atmospheric pressure plasma is a novel approach for wound healing, blood coagulation, and cancer therapy. A recent discovery in the field of plasma medicine is that non-thermal atmospheric pressure plasma not only directly but also indirectly affects cells via plasma-treated liquids. This discovery has led to the use of non-thermal atmospheric pressure plasma as a novel chemotherapy. We refer to these plasma-treated liquids as plasma-activated liquids. We chose Ringer's solutions to produce plasma-activated liquids for clinical applications. In vitro and in vivo experiments demonstrated that plasma-activated Ringer's lactate solution has anti-tumor effects, but of the four components in Ringer's lactate solution, only lactate exhibited anti-tumor effects through activation by non-thermal plasma. Nuclear magnetic resonance analyses indicate that plasma irradiation generates acetyl and pyruvic acid-like groups in Ringer's lactate solution. Overall, these results suggest that plasma-activated Ringer's lactate solution is promising for chemotherapy.

  13. Simulations of planar non-thermal plasma assisted ignition at atmospheric pressure

    KAUST Repository

    Casey, Tiernan A.

    2016-10-21

    The opportunity for ignition assistance by a pulsed applied voltage is investigated in a canonical one-dimensional configuration. An incipient ignition kernel, formed by localized energy deposition into a lean mixture of methane and air at atmospheric pressure, is subjected to sub-breakdown electric fields (E/N ≈ 100 Td) by a DC potential applied across the domain, resulting in non-thermal behavior of the plasma formed during the discharge. A two-fluid approach is employed to couple thermal neutrals and ions to the non-thermal electrons. A two-temperature plasma mechanism describing gas phase combustion, excitation of neutral species, and high-energy electron kinetics is employed to account for non-thermal effects. Charged species transported from the ignition zone drift rapidly through the domain, augmenting the magnitude of the electric field in the fresh gas during the pulse through a dynamic-electrode effect, which results in an increase in the energy of the electrons in the fresh mixture with increasing time. Enhanced fuel and oxidizer decomposition due to electron impact dissociation and interaction with excited neutrals generate a pool of radicals, mostly O and H, in the fresh gas ahead of the flame\\'s preheat zone. In the configuration considered, the effect of the nanosecond pulse is to increase the mass of fuel burned at equivalent times relative to the unsupported ignition through enhanced radical generation, resulting in an increased heat release rate in the immediate aftermath of the pulse.

  14. Crednerite-CuMnO{sub 2} thin films prepared using atmospheric pressure plasma annealing

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Hong-Ying, E-mail: hychen@cc.kuas.edu.tw [Department of Chemical and Materials Engineering, National Kaohsiung University of Applied Sciences, 415 Chiken Kuang Road, Kaohsiung 807, Taiwan, ROC (China); Lin, Yu-Chang [Department of Chemical and Materials Engineering, National Kaohsiung University of Applied Sciences, 415 Chiken Kuang Road, Kaohsiung 807, Taiwan, ROC (China); Lee, Jiann-Shing [Department of Applied Physics, National Pingtung University, 4-18 Minsheng Road, Pingtung City 900, Taiwan, ROC (China)

    2015-05-30

    Highlights: • Crednerite-CuMnO{sub 2} thin films were formed at atmospheric pressure plasma with N{sub 2}–(5–10)%O{sub 2}. • The binding energy of Cu-2p spectrum of the crednerite-CuMnO{sub 2} thin films was 932.3 eV (Cu{sup +}). • The binding energies of Mn-3p spectrum were 48.1 ± 0.2 eV (Mn{sup 3+}) and 50.0 ± 0.2 eV (Mn{sup 4+}). • The cation distribution in the crednerite-CuMnO{sub 2} thin films was Cu{sub 1.0}{sup +}(Mn{sub 0.6}{sup 3+}Mn{sub 0.4}{sup 4+})O{sub 2}. • The electrical conductivity of CuMnO{sub 2} thin films was (2.61–2.65) × 10{sup 4} Ω cm. - Abstract: This study reports the preparation of crednerite-CuMnO{sub 2} thin films using atmospheric pressure plasma annealing. The pristine thin films were deposited onto a quartz substrate using the sol–gel process. The specimens were then annealed using atmospheric pressure plasma at N{sub 2}–(0–20%)O{sub 2} for 20 min. Crednerite-CuMnO{sub 2} thin films were obtained using atmospheric pressure plasma annealing at N{sub 2}–5%O{sub 2} and N{sub 2}–10%O{sub 2}. The lattice parameters of the thin films were a = 0.5574–0.5580 nm, b = 0.2874–0.2879 nm, c = 0.5878–0.5881 nm, and β = 104.15–104.25°, which agree well with previous reports. The Raman shifts of the crednerite-CuMnO{sub 2} thin films were 688 ± 2 cm{sup −1}, 381 ± 2 cm{sup −1}, and 314 ± 2 cm{sup −1}. The binding energy of Cu-2p spectrum of the crednerite-CuMnO{sub 2} thin films was 932.3 ± 0.2 eV representing the Cu{sup +} in the thin films. The binding energies of Mn-3p spectrum were 48.1 ± 0.2 eV (Mn{sup 3+}) and 50.0 ± 0.2 eV (Mn{sup 4+}). Furthermore, the cation distribution in the thin films was Cu{sup +}{sub 1.0}(Mn{sup 3+}{sub 0.6}Mn{sup 4+}{sub 0.4})O{sub 2} from the X-ray photoelectron spectroscopy measurement. When the crednerite-CuMnO{sub 2} phase was formed, the surface morphology exhibited a compact/dense granular morphology. The optical bandgap of the crednerite-CuMnO{sub 2} thin

  15. Heavy metals in particulate and colloidal matter from atmospheric deposition of urban Guangzhou, South China.

    Science.gov (United States)

    Huang, Wen; Duan, Dandan; Zhang, Yulong; Cheng, Hefa; Ran, Yong

    2014-08-30

    Suspended particulate matter (SPM) and colloidal matter (COM) in annual dry and wet deposition samples in urban Guangzhou were for the first time collected, and their trace metals were investigated by using inductively coupled plasma mass spectrometry (ICP-MS). The deposition flux of SPM and of metal elements varied largely among the investigated seasons, and reached the maximum in spring. The correlation analysis indicated that significant correlations existed among some of the metal elements in the deposition samples. The enrichment factors (EF) of metals in COM in the deposition ranging from 79.66 to 130,000 were much higher than those of SPM ranging from 1.65 to 286.48, indicating the important role of COM. The factor analysis showed that emissions from street dust, non-ferrous metal production, and heavy fuel oil were major sources of the trace metals. Positive matrix factorization (PMF) model was used to quantitatively estimate anthropogenic source.

  16. Ultra-small platinum and gold nanoparticles by arc plasma deposition

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Sang Hoon, E-mail: kim_sh@kist.re.kr [Center for Materials Architecturing, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Jeong, Young Eun; Ha, Heonphil; Byun, Ji Young [Center for Materials Architecturing, Korea Institute of Science and Technology (KIST), Seoul 136-791 (Korea, Republic of); Kim, Young Dok [Department of Chemistry, Sungkyunkwan University, Suwon 440-746 (Korea, Republic of)

    2014-04-01

    Highlights: • Ultra-small (<2 nm) and bigger platinum and gold nanoparticles were produced by arc plasma deposition (APD). • Size and coverage of deposited nanoparticles were easily controlled with APD parameters. • Crystalline structures of deposited nanoparticles emerged only when the particle size was bigger than ∼2 nm. - Abstract: Ultra-small (<2 nm) nanoparticles of platinum and gold were produced by arc plasma deposition (APD) in a systematic way and the deposition behavior was studied. Nanoparticles were deposited on two dimensional amorphous carbon and amorphous titania thin films and characterized by transmission electron microscopy (TEM). Deposition behavior of nanoparticles by APD was studied with discharge voltage (V), discharge condenser capacitance (C), and the number of plasma pulse shots (n) as controllable parameters. The average size of intrinsic nanoparticles generated by APD process was as small as 0.9 nm and deposited nanoparticles began to have crystal structures from the particle size of about 2 nm. V was the most sensitive parameter to control the size and coverage of generated nanoparticles compared to C and n. Size of APD deposited nanoparticles was also influenced by the nature of evaporating materials and substrates.

  17. Surface hydrophobic modification of cellulose membranes by plasma-assisted deposition of hydrocarbon films

    OpenAIRE

    Mudtorlep Nisoa; Pikul Wanichapichart

    2010-01-01

    Surface modification by plasma polymerization is an efficient method to change the surface properties of a membrane. Desirable functionality such as hydrophobicity or hydrophilicity can be obtained, depending on plasma chemistry of gas precursors and discharge conditions. In this work, RF magnetron plasma is produced using acetylene and nitrogen as precursor gases. Variations of RF power, particle flux, deposited time and pressure of the precursor gases have been made to observe coating effec...

  18. Surface modification by plasma polymerization: film deposition, tailoring of surface properties and biocompatibility

    OpenAIRE

    Os, van, J.

    2000-01-01

    The work described in this thesis concerns the surface modification of materials by thin film deposition in a plasma reactor. In particular, thin polymeric films bearing amine functionalities were synthesized by plasma polymerization of amino group containing monomers. In addition to the synthesis, attention was directed towards the characterization of these films, and the tailoring of their surface properties on a molecular level. Finally, the amino groups introduced by plasma polymerization...

  19. Plasma properties of a new-type surface wave-sustained plasma source under the conditions of depositing DLC films

    Science.gov (United States)

    Xu, Junqi; Kousaka, Hiroyuki; Umehara, Noritsugu; Diao, Dongfeng

    2006-01-01

    Surface wave-sustained plasma (SWP) is one of the low-pressure, high- density plasma. Applying this technique, diamond-like carbon (DLC) films with excellent characteristics can be prepared by physical vapor deposition (PVD) method. However, the films' application is restricted in some degree, because it is difficult to control the film properties. In this paper, SWP was excited along a conductive rod at a frequency of 2.45 GHz without magnetic fields around the chamber wall. The fundamental theories of plasma diagnostic were presented and plasma properties were studied with a Langmuir probe under the conditions of depositing DLC films by PVD method with a graphite target. Plasma density, electron temperature, plasma potential and target current were measured at difference technique parameters such as gas pressure, microwave power, and so on. As a result, it was proved that plasma properties are greatly affected by microwave power, target voltage and argon gas pressure in chamber. The gas mass flow rate had almost no effect on plasma characters. At the same time, the results indicated that electron density is up to 10 11-10 12cm -3 even at the low pressure of 1 Pa.

  20. Atmospheric Nitrogen Deposition at a Conifer Forest: Canopy Nitrogen Uptake and Photosynthesis

    Science.gov (United States)

    Tomaszewski, T.; Sievering, H.

    2006-12-01

    Atmospheric nitrogen (N) deposition is known to impact forests in a variety of ways ranging from increased growth and photosynthesis to needle necrosis. More than half of the growing-season N deposition flux at the Niwot Ridge Long-Term Ecological Research site's subalpine forest (Niwot Forest) is of anthropogenic origin. N fertilization studies investigating forest responses to increased N deposition have primarily dealt with deposition loading to the soil. However, some studies indicate that forest canopies (especially conifer forest canopies) retain a substantial portion of atmospherically-deposited N before this N reaches the soil in throughfall solutions. In the present study, canopy N uptake (CNU) and the influence of CNU on photosynthesis are investigated. At the Niwot Forest, growing-season throughfall fluxes of ammonium (NH4+) and nitrate (NO3-) are markedly lower (~70% lower) than fluxes in wet plus dry deposition flux, indicating the forest canopy is taking up atmospherically-deposited N. This uptake was found to be driven by diffusion of NH4+ and NO3- into canopy tissues. Although the canopy is taking up atmospherically-deposited N, spruce foliar N content is still relatively low at the Niwot Forest. This low foliar N content contributes to low rates of light-saturated photosynthesis and maximum carboxylation (initial rate of CO2 reduction by RUBISCO). Further, a strong linear dependence of maximum carboxylation on needle N content was found and N solutions that had been directly applied to foliage at Niwot Forest spruce branches induced a 12% greater photosynthetic efficiency (i.e., proportion of absorbed light utilized by photosynthesis). The low foliar N content and dependence of photosynthetic parameters on foliar N content show that the Niwot Forest has yet to reach a state of N saturation. Noting the Niwot Forest has one of the largest N deposition fluxes in the Rockies, our CNU and photosynthetic parameter results characterizing pre