Building Protection Against External Ionizing Fallout Radiation

Energy Technology Data Exchange (ETDEWEB)

Dillon, Michael B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Homann, Steven G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-12-01

A nuclear explosion has the potential to injure or kill tens to hundreds of thousands of people through exposure to fallout (external gamma) radiation. Existing buildings can protect their occupants (reducing external radiation exposures) by placing material and distance between fallout particles and indoor individuals. This protection is not well captured in current fallout risk assessment models and so the US Department of Defense is implementing the Regional Shelter Analysis methodology to improve the ability of the Hazard Prediction and Assessment Capability (HPAC) model to account for building protection. This report supports the HPAC improvement effort by identifying a set of building attributes (next page) that, when collectively specified, are sufficient to calculate reasonably accurate, i.e., within a factor of 2, fallout shelter quality estimates for many individual buildings. The set of building attributes were determined by first identifying the key physics controlling building protection from fallout radiation and then assessing which building attributes are relevant to the identified physics. This approach was evaluated by developing a screening model (PFscreen) based on the identified physics and comparing the screening model results against the set of existing independent experimental, theoretical, and modeled building protection estimates. In the interests of transparency, we have developed a benchmark dataset containing (a) most of the relevant primary experimental data published by prior generations of fallout protection scientists as well as (b) the screening model results.

Assessment of cold neutron radiography capability

International Nuclear Information System (INIS)

McDonald, T.E. Jr.; Roberts, J.A.

1998-01-01

This is the final report of a one-year, Laboratory Directed Research and Development (LDRD) project at Los Alamos National Laboratory (LANL). The authors goals were to demonstrate and assess cold neutron radiography techniques at the Los Alamos Neutron Science Center (LANSCE), Manual Lujan Neutron Scattering Center (Lujan Center), and to investigate potential applications of the capability. The authors have obtained images using film and an amorphous silicon detector. In addition, a new technique they have developed allows neutron radiographs to be made using only a narrow range of neutron energies. Employing this approach and the Bragg cut-off phenomena in certain materials, they have demonstrated material discrimination in radiography. They also demonstrated the imaging of cracks in a sample of a fire-set case that was supplied by Sandia National Laboratory, and they investigated whether the capability could be used to determine the extent of coking in jet engine nozzles. The LANSCE neutron radiography capability appears to have applications in the DOE stockpile maintenance and science-based stockpile stewardship (SBSS) programs, and in industry

Structural reliability assessment capability in NESSUS

Science.gov (United States)

Millwater, H.; Wu, Y.-T.

1992-07-01

The principal capabilities of NESSUS (Numerical Evaluation of Stochastic Structures Under Stress), an advanced computer code developed for probabilistic structural response analysis, are reviewed, and its structural reliability assessed. The code combines flexible structural modeling tools with advanced probabilistic algorithms in order to compute probabilistic structural response and resistance, component reliability and risk, and system reliability and risk. An illustrative numerical example is presented.

Assessing the relationship between youth capabilities and food ...

African Journals Online (AJOL)

Assessing the relationship between youth capabilities and food security: a case study of a rainwater ... among youth and restrict opportunities for them to engage with issues around food and water security. ... AJOL African Journals Online.

Assessment of acquired capability for suicide in clinical practice.

Science.gov (United States)

Rimkeviciene, Jurgita; Hawgood, Jacinta; O'Gorman, John; De Leo, Diego

2016-12-01

The Interpersonal Psychological Theory of suicide proposes that the interaction between Thwarted Belongingness, Perceived Burdensomeness, and Acquired Capability for Suicide (ACS) predicts proximal risk of death by suicide. Instruments to assess all three constructs are available. However, research on the validity of one of them, the acquired capability for suicide scale (ACSS), has been limited, especially in terms of its clinical relevance. This study aimed to explore the utility of the different versions of the ACSS in clinical assessment. Three versions of the scale were investigated, the full 20-item version, a 7-item version and a single item version representing self-perceived capability for suicide. In a sample of patients recruited from a clinic specialising in the treatment of suicidality and in a community sample, all versions of the ACSS were found to show reasonable levels of reliability and to correlate as expected with reports of suicidal ideation, self-harm, and attempted suicide. The item assessing self-perceived acquired capacity for suicide showed highest correlations with all levels of suicidal behaviour. However, no version of the ACSS on its own showed a capacity to indicate suicide attempts in the combined sample. It is concluded that the versions of the scale have construct validity, but their clinical utility is limited. An assessment using a single item on self-perceived ACS outperforms the full and shortened versions of ACSS in clinical settings and can be recommended with caution for clinicians interested in assessing this characteristic.

Assessment of Process Capability: the case of Soft Drinks Processing Unit

Science.gov (United States)

Sri Yogi, Kottala

2018-03-01

The process capability studies have significant impact in investigating process variation which is important in achieving product quality characteristics. Its indices are to measure the inherent variability of a process and thus to improve the process performance radically. The main objective of this paper is to understand capability of the process being produced within specification of the soft drinks processing unit, a premier brands being marketed in India. A few selected critical parameters in soft drinks processing: concentration of gas volume, concentration of brix, torque of crock has been considered for this study. Assessed some relevant statistical parameters: short term capability, long term capability as a process capability indices perspective. For assessment we have used real time data of soft drinks bottling company which is located in state of Chhattisgarh, India. As our research output suggested reasons for variations in the process which is validated using ANOVA and also predicted Taguchi cost function, assessed also predicted waste monetarily this shall be used by organization for improving process parameters. This research work has substantially benefitted the organization in understanding the various variations of selected critical parameters for achieving zero rejection.

Assessment of Mobile Accident Response Capability

International Nuclear Information System (INIS)

1983-03-01

This report presents the results of a DOE-sponsored assessment of nuclear accident response resources. It identifies the mobile resources that could be required to respond to different types of nuclear accidents including major ones like TMI-2, identifies the resources currently available and makes recommendations for the design and construction of additional mobile accident response resources to supplement those already in existence. This project is referred to as the Mobile Accident Response Capability (MARC) program

Emergency Response Capability Baseline Needs Assessment - Compliance Assessment

Energy Technology Data Exchange (ETDEWEB)

Sharry, John A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2016-09-01

This document was prepared by John A. Sharry, LLNL Fire Marshal and Division Leader for Fire Protection and was reviewed by LLNL Emergency Management Department Head, James Colson. This document is the second of a two-part analysis on Emergency Response Capabilities of Lawrence Livermore National Laboratory. The first part, 2016 Baseline Needs Assessment Requirements Document established the minimum performance criteria necessary to meet mandatory requirements. This second part analyses the performance of Lawrence Livermore Laboratory Emergency Management Department to the contents of the Requirements Document. The document was prepared based on an extensive review of information contained in the 2016 BNA, a review of Emergency Planning Hazards Assessments, a review of building construction, occupancy, fire protection features, dispatch records, LLNL alarm system records, fire department training records, and fire department policies and procedures. The 2013 BNA was approved by NNSA’s Livermore Field Office on January 22, 2014.

Assessment of In-Situ Natural Dendroremediation Capability of ...

African Journals Online (AJOL)

Assessment of In-Situ Natural Dendroremediation Capability of Rhizophora racemosa in a Heavy Metal Polluted Mangrove Forest, Rivers State, Nigeria. ... Many of these noxious substances have been noted to be removable from polluted environment through proper application of phytoremediation techniques, particularly ...

Innovation and dynamic capabilities of the firm: Defining an assessment model

Directory of Open Access Journals (Sweden)

André Cherubini Alves

2017-05-01

Full Text Available Innovation and dynamic capabilities have gained considerable attention in both academia and practice. While one of the oldest inquiries in economic and strategy literature involves understanding the features that drive business success and a firm’s perpetuity, the literature still lacks a comprehensive model of innovation and dynamic capabilities. This study presents a model that assesses firms’ innovation and dynamic capabilities perspectives based on four essential capabilities: development, operations, management, and transaction capabilities. Data from a survey of 1,107 Brazilian manufacturing firms were used for empirical testing and discussion of the dynamic capabilities framework. Regression and factor analyses validated the model; we discuss the results, contrasting with the dynamic capabilities’ framework. Operations Capability is the least dynamic of all capabilities, with the least influence on innovation. This reinforces the notion that operations capabilities as “ordinary capabilities,” whereas management, development, and transaction capabilities better explain firms’ dynamics and innovation.

Process for Upgrading Cognitive Assessment Capabilities Onboard the International Space Station

Science.gov (United States)

Picano, J. J.; Seaton, K. A.; Holland, A. W.

2016-01-01

MOTIVATION: Spaceflight poses varied and unique risks to the brain and cognitive functioning including radiation exposure, sleep disturbance, fatigue, fluid shifts (increased intracranial pressure), toxin exposure, elevated carbon dioxide, and traumatic brain injury, among others. These potential threats to cognitive functioning are capable of degrading performance and compromising mission success. Furthermore, the threats may increase in severity, and new types of threats may emerge for longer duration exploration missions. This presentation will describe the process used to identify gaps in our current approach, evaluate best practices in cognitive assessment, and transition new cognitive assessment tools to operational use. OVERVIEW: Risks to brain health and performance posed by spaceflight missions require sensitive tools to assess cognitive functioning of astronauts in flight. The Spaceflight Cognitive Assessment Tool for Windows (WinSCAT) is the automated cognitive assessment tool currently deployed onboard the International Space Station (ISS). WinSCAT provides astronauts and flight surgeons with objective data to monitor neurocognitive functioning. WinSCAT assesses 5 discrete cognitive domains, is sensitive to changes in cognitive functioning, and was designed to be completed in less than 15 minutes. However, WinSCAT does not probe other areas of cognitive functioning that might be important to mission success. Researchers recently have developed batteries that may expand current capabilities, such as increased sensitivity to subtle fluctuations in cognitive functioning. Therefore, we engaged in a systematic process review in order to improve upon our current capabilities and incorporate new advances in cognitive assessment. This process included a literature review on newer measures of neurocognitive assessment, surveys of operational flight surgeons at NASA regarding needs and gaps in our capabilities, and expert panel review of candidate cognitive

Assessing Organizational Capabilities: Reviewing and Guiding the Development of Maturity Grids

DEFF Research Database (Denmark)

Maier, Anja; Moultrie, James; Clarkson, P John

2012-01-01

Managing and improving organizational capabilities is a significant and complex issue for many companies. To support management and enable improvement, performance assessments are commonly used. One way of assessing organizational capabilities is by means of maturity grids. Whilst maturity grids...... than twenty maturity grids places particular emphasis on embedded assumptions about organizational change in the formulation of the maturity ratings. The suggested roadmap encompasses four phases: planning, development, evaluation and maintenance. Each phase discusses a number of decision points...

Assessing Organizational Capability of a Voluntary Organization that ...

African Journals Online (AJOL)

These organizations attached their involvement in CCB as part of their corporate social responsibility-CSR contributions to the society. These NGOs serve as capacity building providers. The major concern is that these NGOs do not have a framework in place to assess their own organizational capability in relations to the ...

Assessing organizational readiness for depression care quality improvement: relative commitment and implementation capability.

Science.gov (United States)

Rubenstein, Lisa V; Danz, Marjorie S; Crain, A Lauren; Glasgow, Russell E; Whitebird, Robin R; Solberg, Leif I

2014-12-02

Depression is a major cause of morbidity and cost in primary care patient populations. Successful depression improvement models, however, are complex. Based on organizational readiness theory, a practice's commitment to change and its capability to carry out the change are both important predictors of initiating improvement. We empirically explored the links between relative commitment (i.e., the intention to move forward within the following year) and implementation capability. The DIAMOND initiative administered organizational surveys to medical and quality improvement leaders from each of 83 primary care practices in Minnesota. Surveys preceded initiation of activities directed at implementation of a collaborative care model for improving depression care. To assess implementation capability, we developed composites of survey items for five types of organizational factors postulated to be collaborative care barriers and facilitators. To assess relative commitment for each practice, we averaged leader ratings on an identical survey question assessing practice priorities. We used multivariable regression analyses to assess the extent to which implementation capability predicted relative commitment. We explored whether relative commitment or implementation capability measures were associated with earlier initiation of DIAMOND improvements. All five implementation capability measures independently predicted practice leaders' relative commitment to improving depression care in the following year. These included the following: quality improvement culture and attitudes (p = 0.003), depression culture and attitudes (p commitment (p = 0.002) and prior depression quality improvement activities appeared to be associated with earlier participation in the DIAMOND initiative. The study supports the concept of organizational readiness to improve quality of care and the use of practice leader surveys to assess it. Practice leaders' relative commitment to depression care

Emergency Response Capability Baseline Needs Assessment - Requirements Document

Energy Technology Data Exchange (ETDEWEB)

Sharry, J A

2016-10-04

This document was prepared by John A. Sharry, LLNL Fire Marshal and LLNL Division Leader for Fire Protection and reviewed by LLNL Emergency Management Department Head James Colson. The document follows and expands upon the format and contents of the DOE Model Fire Protection Baseline Capabilities Assessment document contained on the DOE Fire Protection Web Site, but only addresses emergency response.

Turtle Hearing Capability Based on ABR Signal assessment

Directory of Open Access Journals (Sweden)

Raja Bidin Raja Hassan

2010-08-01

Full Text Available Sea turtles have existed for millions of years. International Union for Conservation of Nature (IUCN has reported that the Hawksbill Turtle (Eretmochelys imbricata is classified as critically endangered. Turtle excluder device (TED deployment on shrimpnet fisheries is needed for turtle conservation.TED using sound technique is challenge method in fisheries development.The knowledge on turtle hearing capability is limited. The auditory brainstem response (ABR assessment is method to determine turtle hearing capability. Turtle hearing assessment is basis to design TED. The objective of this paper is to determine turtle hearing cability by analyze its ABR spectral.The subject is Hawksbill turtle with number 2 turtles ie: 3 and 2 years. The measurement was taken at Pusat Pengurusan Penyu (Turtle Management Centre Padang Kemunting Masjid Tanah Melaka Malaysia. The results shows that turtle 3 years have peak power frequencies 50.78, 101.6, 152.3, 304.7, 355.5, 457, and 507.8Hz respectively whereas the spectral amplitude is ranging 0.03-32.44% spectral. Turtle 2 years has peak power at 457Hz in whole stimulus frequencies while the spectral amplitude is ranging 0.01-2.5% spectral.

Implementation of a health policy advisory committee as a knowledge translation platform: the Nigeria experience

Science.gov (United States)

Uneke, Chigozie Jesse; Ndukwe, Chinwendu Daniel; Ezeoha, Abel Abeh; Uro-Chukwu, Henry Chukwuemeka; Ezeonu, Chinonyelum Thecla

2015-01-01

Background: In recent times, there has been a growing demand internationally for health policies to be based on reliable research evidence. Consequently, there is a need to strengthen institutions and mechanisms that can promote interactions among researchers, policy-makers and other stakeholders who can influence the uptake of research findings. The Health Policy Advisory Committee (HPAC) is one of such mechanisms that can serve as an excellent forum for the interaction of policy-makers and researchers. Therefore, the need to have a long term mechanism that allows for periodic interactions between researchers and policy-makers within the existing government system necessitated our implementation of a newly established HPAC in Ebonyi State Nigeria, as a Knowledge Translation (KT) platform. The key study objective was to enhance the capacity of the HPAC and equip its members with the skills/competence required for the committee to effectively promote evidence informed policy-making and function as a KT platform. Methods: A series of capacity building programmes and KT activities were undertaken including: i) Capacity building of the HPAC using Evidence-to-Policy Network (EVIPNet) SUPPORT tools; ii) Capacity enhancement mentorship programme of the HPAC through a three-month executive training programme on health policy/health systems and KT in Ebonyi State University Abakaliki; iii) Production of a policy brief on strategies to improve the performance of the Government’s Free Maternal and Child Health Care Programme in Ebonyi State Nigeria; and iv) Hosting of a multi-stakeholders policy dialogue based on the produced policy brief on the Government’s Free Maternal and Child Health Care Programme. Results: The study findings indicated a noteworthy improvement in knowledge of evidence-to-policy link among the HPAC members; the elimination of mutual mistrust between policy-makers and researchers; and an increase in the awareness of importance of HPAC in the Ministry

Implementation of a Health Policy Advisory Committee as a Knowledge Translation Platform: The Nigeria Experience

Directory of Open Access Journals (Sweden)

Chigozie Jesse Uneke

2015-03-01

Full Text Available Background In recent times, there has been a growing demand internationally for health policies to be based on reliable research evidence. Consequently, there is a need to strengthen institutions and mechanisms that can promote interactions among researchers, policy-makers and other stakeholders who can influence the uptake of research findings. The Health Policy Advisory Committee (HPAC is one of such mechanisms that can serve as an excellent forum for the interaction of policy-makers and researchers. Therefore, the need to have a long term mechanism that allows for periodic interactions between researchers and policy-makers within the existing government system necessitated our implementation of a newly established HPAC in Ebonyi State Nigeria, as a Knowledge Translation (KT platform. The key study objective was to enhance the capacity of the HPAC and equip its members with the skills/competence required for the committee to effectively promote evidence informed policy-making and function as a KT platform. Methods A series of capacity building programmes and KT activities were undertaken including: i Capacity building of the HPAC using Evidence-to-Policy Network (EVIPNet SUPPORT tools; ii Capacity enhancement mentorship programme of the HPAC through a three-month executive training programme on health policy/health systems and KT in Ebonyi State University Abakaliki; iii Production of a policy brief on strategies to improve the performance of the Government’s Free Maternal and Child Health Care Programme in Ebonyi State Nigeria; and iv Hosting of a multi-stakeholders policy dialogue based on the produced policy brief on the Government’s Free Maternal and Child Health Care Programme. Results The study findings indicated a noteworthy improvement in knowledge of evidence-to-policy link among the HPAC members; the elimination of mutual mistrust between policy-makers and researchers; and an increase in the awareness of importance of HPAC in the

Fire fighting capability assessment program Darlington NGS

International Nuclear Information System (INIS)

1995-05-01

This is a report on the completion of work relating to the assessment of the capability of Darlington NGS to cope with a large fire incident. This included an evaluation of an exercise scenario that would simulate a large fire incident and of their fire plans and procedures which became the subject of interim reports as part of the process of preparing for the fire fighting and rescue exercise. Finally the execution of fire plans by Darlington Nuclear Generating Station (NGS), as demonstrated by their application of human and material resources during a simulated large fire, was observed. 1 tab., 1 fig

Facility Interface Capability Assessment (FICA) user manual

International Nuclear Information System (INIS)

Pope, R.B.; MacDonald, R.R.; Massaglia, J.L.; Williamson, D.A.; Viebrock, J.M.; Mote, N.

1995-09-01

The US Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is responsible for developing the Civilian Radioactive Waste Management System (CRWMS) to accept spent nuclear fuel from commercial facilities. The objective of the Facility Interface Capability Assessment (FICA) project was to assess the capability of each commercial spent nuclear fuel (SNF) storage facility, at which SNF is stored, to handle various SNF shipping casks. The purpose of this report is describe the FICA computer software and to provide the FICA user with a guide on how to use the FICA system. The FICA computer software consists of two executable programs: the FICA Reactor Report program and the FICA Summary Report program (written in the Ca-Clipper version 5.2 development system). The complete FICA software system is contained on either a 3.5 in. (double density) or a 5.25 in. (high density) diskette and consists of the two FICA programs and all the database files (generated using dBASE III). The FICA programs are provided as ''stand alone'' systems and neither the Ca-Clipper compiler nor dBASE III is required to run the FICA programs. The steps for installing the FICA software system and executing the FICA programs are described in this report. Instructions are given on how to install the FICA software system onto the hard drive of the PC and how to execute the FICA programs from the FICA subdirectory on the hard drive. Both FICA programs are menu driven with the up-arrow and down-arrow keys used to move the cursor to the desired selection

Simultaneous high-throughput determination of interaction kinetics for drugs and cyclodextrins by high performance affinity chromatography with mass spectrometry detection.

Science.gov (United States)

Wang, Caifen; Wang, Xiaobo; Xu, Xiaonan; Liu, Botao; Xu, Xu; Sun, Lixin; Li, Haiyan; Zhang, Jiwen

2016-02-25

The individual determination of the apparent dissociation rate constant (kd,app) using high performance affinity chromatography (HPAC) is a tedious process requiring numerous separate tests and massive data fitting, unable to provide the apparent association rate constant (ka) and equilibrium binding constant (Ka). In this study, a HPAC with mass spectrometry detection (HPAC-MS/MS) was employed to determine the drug-cyclodextrin (CD) interaction kinetics with low sample loading quantity (drugs determined in one injection. The kd,app measured by HPAC-MS/MS approach were 0.89 ± 0.07, 4.34 ± 0.01, 1.48 ± 0.01 and 7.77 ± 0.04 s(-1) for ketoprofen, trimethoprim, indapamide and acetaminophen, with kd,app for acetaminophen consistent with that from the HPAC method with UV detector in our previous studies. For twenty drugs with diverse structures and chemical properties, good correlationship was found between kd,app measured by single compound analysis method and high-throughput HPAC-MS/MS approach, with the correlation coefficient of 0.987 and the significance F less than 0.001. Comprehensive quantification of ka,app, kd,app and Ka values was further performed based on the measurement of kd,app by peak profiling method and Ka by the peak fitting method. And the investigation of the drug-CD interaction kinetics under different conditions indicated that the column temperature and mobile phase composition significantly affected the determination of ka,app, kd,app and Ka while also dependent on the acidity and basicity of drugs. In summary, the high-throughput HPAC-MS/MS approach has been demonstrated high efficiency in determination of the drug-CD primary interaction kinetic parameter, especially, kd,app, being proven as a novel tool in screening the right CD for the solubilization of the right drug. Copyright © 2016 Elsevier B.V. All rights reserved.

A Process for Assessing NASA's Capability in Aircraft Noise Prediction Technology

Science.gov (United States)

Dahl, Milo D.

2008-01-01

An acoustic assessment is being conducted by NASA that has been designed to assess the current state of the art in NASA s capability to predict aircraft related noise and to establish baselines for gauging future progress in the field. The process for determining NASA s current capabilities includes quantifying the differences between noise predictions and measurements of noise from experimental tests. The computed noise predictions are being obtained from semi-empirical, analytical, statistical, and numerical codes. In addition, errors and uncertainties are being identified and quantified both in the predictions and in the measured data to further enhance the credibility of the assessment. The content of this paper contains preliminary results, since the assessment project has not been fully completed, based on the contributions of many researchers and shows a select sample of the types of results obtained regarding the prediction of aircraft noise at both the system and component levels. The system level results are for engines and aircraft. The component level results are for fan broadband noise, for jet noise from a variety of nozzles, and for airframe noise from flaps and landing gear parts. There are also sample results for sound attenuation in lined ducts with flow and the behavior of acoustic lining in ducts.

ATTITUDE ASSESSMENT USING PLEIADES-HR CAPABILITIES

Directory of Open Access Journals (Sweden)

J. M. Delevit

2012-07-01

Full Text Available Since SPOT1, the French national space centre (CNES has worked on improving the geometry of Earth observation spacecrafts. The accuracy of sensor calibration is one of the main key points for any Earth observation application such as orthorectification, DEM generation or surface change detection. For the last twenty years CNES has developed two families of methods: absolute methods and relative methods. These methods are used to characterize a pushbroom acquisition along the detector line and the time line. By this way, the viewing directions are measured and the residual of the spacecraft’s attitude angles (not restituted by the Attitude and Orbit Control System is estimated. This information can complete the geometric model of all the scenes acquired by the instrument and is used in all geometric applications. This paper presents new attitude assessment methods taking advantage of the capabilities of Pléiades-HR in terms of agility and focal plane arrangement – panchromatic band and multispectral (MS bands.

Analytical Chemistry Core Capability Assessment - Preliminary Report

International Nuclear Information System (INIS)

Barr, Mary E.; Farish, Thomas J.

2012-01-01

The concept of 'core capability' can be nebulous one. Even at a fairly specific level, where core capability equals maintaining essential services, it is highly dependent upon the perspective of the requestor. Samples are submitted to analytical services because the requesters do not have the capability to conduct adequate analyses themselves. Some requests are for general chemical information in support of R and D, process control, or process improvement. Many analyses, however, are part of a product certification package and must comply with higher-level customer quality assurance requirements. So which services are essential to that customer - just those for product certification? Does the customer also (indirectly) need services that support process control and improvement? And what is the timeframe? Capability is often expressed in terms of the currently utilized procedures, and most programmatic customers can only plan a few years out, at best. But should core capability consider the long term where new technologies, aging facilities, and personnel replacements must be considered? These questions, and a multitude of others, explain why attempts to gain long-term consensus on the definition of core capability have consistently failed. This preliminary report will not try to define core capability for any specific program or set of programs. Instead, it will try to address the underlying concerns that drive the desire to determine core capability. Essentially, programmatic customers want to be able to call upon analytical chemistry services to provide all the assays they need, and they don't want to pay for analytical chemistry services they don't currently use (or use infrequently). This report will focus on explaining how the current analytical capabilities and methods evolved to serve a variety of needs with a focus on why some analytes have multiple analytical techniques, and what determines the infrastructure for these analyses. This information will be

Academic Leaders' Perspectives on Adopting ePortfolios for Developing and Assessing Professional Capabilities in Australian Business Education

Science.gov (United States)

Holt, Dale; McGuigan, Nicholas; Kavanagh, Marie; Leitch, Shona; Ngo, Leanne; Salzman, Scott; Watty, Kim; McKay, Jade

2016-01-01

This paper represents a major stage of data collection and reporting on an Australian Office for Learning and Teaching Innovation and Development grant investigating the adoption of ePortfolios for developing and assessing professional capabilities in Australian undergraduate business education. Assessing desired capabilities with and through…

Development of students learning capabilities and professional capabilities

DEFF Research Database (Denmark)

Ringtved, Ulla Lunde; Wahl, Christian; Belle, Gianna

This paper describes the work-in-progress on a project that aims todevelop a tool that via learning analytic methods enable studentsto enhance, document and assess the development of their learningcapabilities and professional capabilities in consequence of theirself-initiated study activities...... during their bachelor educations. Thetool aims at enhancing the development of students’ capabilities toself-initiate, self-regulate and self-assess their study activities.The tool uses the concept of collective intelligence as source formotivation and inspiration in self-initiating study activities...... as wellas self-assessing them. The tool is based on a heutagogical approachto support reflection on learning potential in these activities. Thisenhances the educational use of students self-initiated learningactivities by bringing visibility and evidence to them, and therebybringing value to the assessment...

Reliability Analysis and Overload Capability Assessment of Oil-Immersed Power Transformers

Directory of Open Access Journals (Sweden)

Chen Wang

2016-01-01

Full Text Available Smart grids have been constructed so as to guarantee the security and stability of the power grid in recent years. Power transformers are a most vital component in the complicated smart grid network. Any transformer failure can cause damage of the whole power system, within which the failures caused by overloading cannot be ignored. This research gives a new insight into overload capability assessment of transformers. The hot-spot temperature of the winding is the most critical factor in measuring the overload capacity of power transformers. Thus, the hot-spot temperature is calculated to obtain the duration running time of the power transformers under overloading conditions. Then the overloading probability is fitted with the mature and widely accepted Weibull probability density function. To guarantee the accuracy of this fitting, a new objective function is proposed to obtain the desired parameters in the Weibull distributions. In addition, ten different mutation scenarios are adopted in the differential evolutionary algorithm to optimize the parameter in the Weibull distribution. The final comprehensive overload capability of the power transformer is assessed by the duration running time as well as the overloading probability. Compared with the previous studies that take no account of the overloading probability, the assessment results obtained in this research are much more reliable.

An assessment of the process capabilities of nanoimprint lithography

Science.gov (United States)

Balla, Tobias; Spearing, S. Mark; Monk, Andrew

2008-09-01

Nanoimprint lithography (NIL) is an emerging nanofabrication tool, able to replicate imprint patterns quickly and at high volumes. The present study was performed in order to define the capabilities of NIL, based on a study of published research and to identify the application areas where NIL has the greatest potential. The process attributes of different NIL process chains were analysed, and their process capabilities were compared to identify trends and process limitations. The attributes chosen include the line width, relief height, initial resist thickness, residual layer thickness, imprint area and line width tolerances. In each case well-defined limits can be identified, which are a direct result of the mechanisms involved in the NIL process. These quantitative results were compared with the assessments of individuals in academia and within the microfabrication industry. The results suggest NIL is most suited to producing photonic, microfluidic and patterned media applications, with photonic applications the closest to market. NIL needs to address overlay alignment issues for wider use, while an analysis is needed for each market, as to whether NIL adds value.

Assessing the Impact of IT Competency on Organizational Learning Capability of Indonesian Manufacturing Firms

Directory of Open Access Journals (Sweden)

Alizar Hasan

2010-01-01

Full Text Available This paper attempt to assessing the impact of IT competency on organizational learning capability by using the measurement scale that have been developed by Tippins et al. and Gomes et al. These studies cover a sample of 192 manufacturing firms. IT competencies are classified into three dimensions: IT knowledge, IT operations, and IT objects, and organizational learning capability are classified into four dimensions: Managerial commitment, System perspec-tive, Openness and experimentation, and Knowledge transfer and integration. The result of factor analysis on IT competency and Organizational learning capability show that all items have high loading only on a single factor with ranging from .60 to .84. The findings revealed that IT competency positively and significantly influences the organizational learning capability of Indonesian manufacturing firms.

UK resource base assessment of organisations and capabilities in the biomass sector

International Nuclear Information System (INIS)

1996-01-01

British Biogen is the trade association for the UK's emerging biomass industry. It has been recognised that the biomass industry has considerable export potential due to its immense scale potential overseas, and there is an accompanying need for an export development strategy for the industry. The report contains a detailed analysis of a selection of UK companies and organisations, with regard to their export capabilities, thus providing an essential pre-requisite to developing the export strategy. The fundamental aim of the study is to assess the nature, scale and current capabilities of the UK biomass industry resource base and, in turn, to determine its potential to service export markets. (author)

Applying a multi-replication framework to support dynamic situation assessment and predictive capabilities

Science.gov (United States)

Lammers, Craig; McGraw, Robert M.; Steinman, Jeffrey S.

2005-05-01

Technological advances and emerging threats reduce the time between target detection and action to an order of a few minutes. To effectively assist with the decision-making process, C4I decision support tools must quickly and dynamically predict and assess alternative Courses Of Action (COAs) to assist Commanders in anticipating potential outcomes. These capabilities can be provided through the faster-than-real-time predictive simulation of plans that are continuously re-calibrating with the real-time picture. This capability allows decision-makers to assess the effects of re-tasking opportunities, providing the decision-maker with tremendous freedom to make time-critical, mid-course decisions. This paper presents an overview and demonstrates the use of a software infrastructure that supports DSAP capabilities. These DSAP capabilities are demonstrated through the use of a Multi-Replication Framework that supports (1) predictivie simulations using JSAF (Joint Semi-Automated Forces); (2) real-time simulation, also using JSAF, as a state estimation mechanism; and, (3) real-time C4I data updates through TBMCS (Theater Battle Management Core Systems). This infrastructure allows multiple replications of a simulation to be executed simultaneously over a grid faster-than-real-time, calibrated with live data feeds. A cost evaluator mechanism analyzes potential outcomes and prunes simulations that diverge from the real-time picture. In particular, this paper primarily serves to walk a user through the process for using the Multi-Replication Framework providing an enhanced decision aid.

Assessment of Equipment Capability to Perform Reliably under Severe Accident Conditions

International Nuclear Information System (INIS)

2017-07-01

The experience from the last 40 years has shown that severe accidents can subject electrical and instrumentation and control (I&C) equipment to environmental conditions exceeding the equipment’s original design basis assumptions. Severe accident conditions can then cause rapid degradation or damage to various degrees up to complete failure of such equipment. This publication provides the technical basis to consider when assessing the capability of electrical and I&C equipment to perform reliably during a severe accident. It provides examples of calculation tools to determine the environmental parameters as well as examples and methods that Member States can apply to assess equipment reliability.

Quality control and process capability assessment for injection-moulded micro mechanical parts

DEFF Research Database (Denmark)

Gasparin, Stefania; Tosello, Guido; Hansen, Hans Nørgaard

2013-01-01

Quality control of micro components is an increasing challenge. Smaller mechanical parts are characterized by smaller tolerance to be verified. This paper focuses on the dimensional verification of micro injection-moulded components selected from an industrial application. These parts are measured...... using an optical coordinate measuring machine, which guarantees fast surface scans suitable for inline quality control. The uncertainty assessment of the measurements is calculated and three analyses are carried out and discussed in order to investigate the influence parameters in optical coordinate...... metrology. The estimation of the total variability of the optical measurements and the instrument repeatability are reported; moreover, the measurement system capability is evaluated according to the measurement system capability indices Cg and Cgk....

Developing Alliance Capabilities

DEFF Research Database (Denmark)

Heimeriks, Koen H.; Duysters, Geert; Vanhaverbeke, Wim

This paper assesses the differential performance effects of learning mechanisms on the development of alliance capabilities. Prior research has suggested that different capability levels could be identified in which specific intra-firm learning mechanisms are used to enhance a firm's alliance...

The capability concept – On how to define and describe capability in relation to risk, vulnerability and resilience

International Nuclear Information System (INIS)

Lindbom, Hanna; Tehler, Henrik; Eriksson, Kerstin; Aven, Terje

2015-01-01

Capabilities-based planning and capability assessment are high on the agendas of several countries and organisations as part of their risk management and emergency preparedness. Despite this, few definitions of capability exist, and they are not easily related to concepts such as risk, vulnerability and resilience. The aim of the present study was thus to broaden the scientific basis of the risk field to also include the concept of capability. The proposed definition is based on a recently developed risk framework, and we define capability as the uncertainty about and the severity of the consequences of an activity given the occurrence of the initiating event and the performed task. We provide examples of how the response capability for a fictive scenario can be described using this definition, and illustrate how our definition can be used to analyse capability assessments prepared according to the Swedish crisis management system. We have analysed the content of 25 capability assessments produced in 2011 by stakeholders on local, regional and national level. It was concluded that none addressed uncertainty to any appreciable extent, and only a third described capability in terms of consequences and task, making it difficult to relate these capability assessments to risk assessments. - Highlights: • Few definitions of capability relate to definitions of risk, vulnerability and resilience. • We relate capability to risk, vulnerability and resilience. • We define capability using the components uncertainty, consequences, event and task

Upgrading Regional Capability to Assess Marine Contaminants in the ARASIA member States

International Nuclear Information System (INIS)

ELSamad, O.

2010-01-01

This project enhances the national capabilities to monitor and assess marine radioactivity as part of a national monitoring program. This will be very beneficial as, the monitoring processes and control of marine pollution is a very strategic important objective of the governments, while many national decrees recently issued includes environmental protection and rehabilitation of the marine environment. (author)

Assessment of capabilities in persons with advanced stage of dementia: Validation of The Montessori Assessment System (MAS).

Science.gov (United States)

Erkes, Jérôme; Camp, Cameron J; Raffard, Stéphane; Gély-Nargeot And, Marie-Christine; Bayard, Sophie

2017-01-01

This study evaluated the validity and reliability of the Montessori Assessment System. The Montessori Assessment System assesses preserved abilities in persons with moderate to severe dementia. In this respect, this instrument provides crucial information for the development of effective person-centered care plans. A total of 196 persons with a diagnosis of dementia in the moderate to severe stages of dementia were recruited in 10 long-term care facilities in France. All participants completed the Montessori Assessment System, the Clinical Dementia Rating Scale and/or the Mini Mental State Examination and the Severe Impairment Battery-short form. The internal consistency and temporal stability of the Montessori Assessment System were high. Additionally, good construct and divergent validity were demonstrated. Factor analysis showed a one-factor structure. The Montessori Assessment System demonstrated satisfactory psychometric properties while being a useful instrument to assess capabilities in persons with advanced stages of dementia and hence to develop person-centered plans of care.

Code Verification Capabilities and Assessments in Support of ASC V&V Level 2 Milestone #6035

Energy Technology Data Exchange (ETDEWEB)

Doebling, Scott William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Budzien, Joanne Louise [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Ferguson, Jim Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Harwell, Megan Louise [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hickmann, Kyle Scott [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Israel, Daniel M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Magrogan, William Richard III [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Singleton, Jr., Robert [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Srinivasan, Gowri [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Walter, Jr, John William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Woods, Charles Nathan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-09-26

This document provides a summary of the code verification activities supporting the FY17 Level 2 V&V milestone entitled “Deliver a Capability for V&V Assessments of Code Implementations of Physics Models and Numerical Algorithms in Support of Future Predictive Capability Framework Pegposts.” The physics validation activities supporting this milestone are documented separately. The objectives of this portion of the milestone are: 1) Develop software tools to support code verification analysis; 2) Document standard definitions of code verification test problems; and 3) Perform code verification assessments (focusing on error behavior of algorithms). This report and a set of additional standalone documents serve as the compilation of results demonstrating accomplishment of these objectives.

Introductory materials for committee members: 1) instructions for the Los Alamos National Laboratory fiscal year 2010 capability reviews 2) NPAC strategic capability planning 3) Summary self-assessment for the nuclear and particle physics, astrophysics an

Energy Technology Data Exchange (ETDEWEB)

Redondo, Antonio [Los Alamos National Laboratory

2010-01-01

Los Alamos National Laboratory (LANL) uses external peer review to measure and continuously improve the quality of its science, technology and engineering (STE). LANL uses capability reviews to assess the STE quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. STE capabilities are define to cut across directorates providing a more holistic view of the STE quality, integration to achieve mission requirements, and mission relevance. The scope of these capabilities necessitate that there will be significant overlap in technical areas covered by capability reviews (e.g., materials research and weapons science and engineering). In addition, LANL staff may be reviewed in different capability reviews because of their varied assignments and expertise. LANL plans to perform a complete review of the Laboratory's STE capabilities (hence staff) in a three-year cycle. The principal product of an external review is a report that includes the review committee's assessments, commendations, and recommendations for STE. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). This report will be used by Laboratory Management for STE assessment and planning. The report is also provided to the Department of Energy (DOE) as part of LANL's Annual Performance Plan and to the Los Alamos National Security (LANS) LLC's Science and Technology Committee (STC) as part of its responsibilities to the LANS Board of Governors.

Power transfer capability assessment of transmission interfaces with SVC and load shedding systems

Energy Technology Data Exchange (ETDEWEB)

Pavlovsky, V. [DMCC-Engineering, Kiev (Ukraine). Inst. of Electrodynamics; Dolzhenitsa, Y. [DMCC Engineering, Kiev (Ukraine); Ushapovskiy, K. [National Power Co. Ukrenergo, Kiev (Ukraine)

2009-07-01

As a result of deregulation in the power industry, energy trade and markets are pushing transmission system operators to operate their systems closer to the edge of the power transfer capability. Voltage instability and inadequate reactive power support of generators is a key factor in most major outages around the world. The ideal way to control power systems is to avoid emergencies by reliable planning and secure operation of power systems. Therefore, the accurate calculation of the power transfer capability of transmission interfaces is an important task on the planning and operation stages. This paper discussed the issue of transfer capability assessment and monitoring for interfaces with static var compensator (SVC) and load shedding schemes. It also proposed a special measure, a distance to voltage instability point, to monitor transfer capability on-line. The distance may be observed by measurement of SVC output. The paper considered the problem of optimal SVC size selection and a new approach was proposed based on P-V curves analysis. The paper discussed the problem formulation and proposed approach. A case was also presented in order to demonstrate the proposed approach on the IPS Ukraine-Crimea interface. It was concluded that the proposed approach allows the optimal rating of SVC for increasing transfers capability of transmission corridors. 12 refs., 9 figs.

The evolution of alliance capabilities

NARCIS (Netherlands)

Heimeriks, K.H.; Duysters, G.M.; Vanhaverbeke, W.P.M.

2004-01-01

This paper assesses the effectiveness and differential performance effects of learning mechanisms on the evolution of alliance capabilities. Relying on the concept of capability lifecycles, prior research has suggested that different capability levels could be identified in which different

Combining Capability Assessment and Value Engineering: a New Two-dimensional Method for Software Process Improvement

Directory of Open Access Journals (Sweden)

Pasi Ojala

2008-02-01

Full Text Available During the last decades software process improvement (SPI has been recognized as a usable possibility to increase the quality of software development. Implemented SPI investments have often indicated increased process capabilities as well. Recently more attention has been focused on the costs of SPI as well as on the cost-effectiveness and productivity of software development, although the roots of economic-driven software engineering originate from the very early days of software engineering research. This research combines Value Engineering and capability assessment into usable new method in order to better respond to the challenges that cost-effectiveness and productivity has brought to software companies. This is done in part by defining the concepts of value, worth and cost and in part by defining the Value Engineering process and different enhancements it has seen to offer to software assessment. The practical industrial cases show that proposed two-dimensional method works in practise and is useful to assessed companies.

A hybrid MCDM framework combined with DEMATEL-based ANP to evaluate enterprise technological innovation capabilities assessment

Directory of Open Access Journals (Sweden)

Meng-Jong Kuan

2014-08-01

Full Text Available The efficient evaluation of technological innovation capabilities of enterprises is an important factor to enhance competitiveness. This paper aims to assess and to rank technological innovation evaluation criteria in order to provide a practical insight of systematic analysis by gathering the qualified experts’ opinions combined with three methods of multi-criteria decision making approach. A framework is proposed and uses a novel hybrid multiple criteria decision-making (MCDM model to address the dependence relationships of criteria with the aid of the Decision-Making Trial and Evaluation Laboratory (DEMATEL, analytical network process (ANP and VIKOR (VlseKriterijumska Optimizacija I Kompromisno Resenje. The study reports that the interaction between criteria is essential and influences technological innovation capabilities; furthermore, this ranking development of technological innovation capabilities assessment is also one of key management tools for managements of other related high- tech enterprises. Managers can then judge the need to improve and determine which criteria provide the most effective direction towards improvement.

Fire fighting capability assessment program Bruce B NGS

International Nuclear Information System (INIS)

1995-05-01

This is a report on the completion of work relating to the assessment of the capability of Bruce B NGS to cope with a large fire incident. This included an evaluation of an exercise scenario that would simulate a large fire incident and of their fire plans and procedures. Finally the execution of fire plans by Bruce B NGS, as demonstrated by their application of human and material resources during a simulated large fire, was observed. The fire fighting equipment and the personal protective clothing and associated equipment that was in use was all of good quality and in good condition. There had also been notable improvement in communications equipment. Similarly, the human resources that had been assigned to fire fighting and rescue crews and that were available were more than adequate. Use of a logical incident command system, and the adoption of proper policy and procedures for radio communications were equally significant improvements. Practice should correct the breakdowns that occurred in these areas during the exercise. As well, there remains a need for the development of policy on fire fighting and rescue operations with more depth and clarity. In summary, the key point to be recognized is the degree of improvement that has been realized since the previous evaluation in 1990. Clearly the Emergency Response Teams organization of Bruce B NGS is evolving into an effective fire fighting force. Providing that the deficiencies identified in this report are addressed satisfactorily, Fire Cross is confident that the organization will have the capability to provide rescue and fire fighting services that will satisfy the need. 2 figs

A systems engineering cost analysis capability for use in assessing nuclear waste management system cost performance

International Nuclear Information System (INIS)

Shay, M.R.

1990-04-01

The System Engineering Cost Analysis (SECA) capability has been developed by the System Integration Branch of the US Department of Energy's Office of Civilian Radioactive Waste Management for use in assessing the cost performance of alternative waste management system configurations. The SECA capability is designed to provide rapid cost estimates of the waste management system for a given operational scenario and to permit aggregate or detailed cost comparisons for alternative waste system configurations. This capability may be used as an integral part of the System Integration Modeling System (SIMS) or, with appropriate input defining a scenario, as a separate cost analysis model

Assessment of CFD Capability for Hypersonic Shock Wave Laminar Boundary Layer Interactions

OpenAIRE

Mehrnaz Rouhi Youssefi; Doyle Knight

2017-01-01

The goal of this study is to assess CFD capability for the prediction of shock wave laminar boundary layer interactions at hypersonic velocities. More specifically, the flow field over a double-cone configuration is simulated using both perfect gas and non-equilibrium Navier–Stokes models. Computations are compared with recent experimental data obtained from measurements conducted in the LENS XX (Large Energy National Shock Expansion Tunnel Version 2) at the Calspan University of Buffalo Rese...

Capabilities and Gaps Assessments of Urban Air Quality Manage-ment in Uganda

OpenAIRE

Amin Tamale Kiggundu

2015-01-01

Today, large cities across the globe are facing a pervasive problem of air pollution.  The purpose of this study is to assess the capabilities and gaps in urban air quality management in Uganda as well as proposing strategies for curbing air pollution. This study applied face to face interviews, targeting key informants such as the environmental experts, urbanization researchers and officials from the National Environment Management Authority (NEMA). Results show that rapid motorization, cont...

American National Standard: criteria and guidelines for assessing capability for surface faulting at nuclear power plant sites

International Nuclear Information System (INIS)

Anon.

1982-01-01

This standard provides applicants and consultants with criteria and guidelines for investigations directed toward the assessment of the capability for surface faulting at nuclear power plant sites. Assessment of vibratory ground motion resulting from faulting is not treated in these guidelines

Accelerator and Electrodynamics Capability Review

International Nuclear Information System (INIS)

Jones, Kevin W.

2010-01-01

Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

Accelerator and electrodynamics capability review

Energy Technology Data Exchange (ETDEWEB)

Jones, Kevin W [Los Alamos National Laboratory

2010-01-01

Los Alamos National Laboratory (LANL) uses capability reviews to assess the science, technology and engineering (STE) quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). Laboratory Management will use this report for STE assessment and planning. LANL has defined fifteen STE capabilities. Electrodynamics and Accelerators is one of the seven STE capabilities that LANL Management (Director, PADSTE, technical Associate Directors) has identified for review in Fiscal Year (FY) 2010. Accelerators and electrodynamics at LANL comprise a blend of large-scale facilities and innovative small-scale research with a growing focus on national security applications. This review is organized into five topical areas: (1) Free Electron Lasers; (2) Linear Accelerator Science and Technology; (3) Advanced Electromagnetics; (4) Next Generation Accelerator Concepts; and (5) National Security Accelerator Applications. The focus is on innovative technology with an emphasis on applications relevant to Laboratory mission. The role of Laboratory Directed Research and Development (LDRD) in support of accelerators/electrodynamics will be discussed. The review provides an opportunity for interaction with early career staff. Program sponsors and customers will provide their input on the value of the accelerator and electrodynamics capability to the Laboratory mission.

Demonstration of a repository performance assessment capability at the US Nuclear Regulatory Commission

International Nuclear Information System (INIS)

Codell, R.; Eisenberg, N.; McCartin, T.; Park, J.

1991-01-01

In order to better review licensing submittals for a High-Level Waste Repository, the US Nuclear Regulatory Commission staff has expanded and improved its capability to conduct performance assessments. A demonstration of this capability used the limited data from Yucca Mountain, Nevada to investigate a small set of scenario classes. Models of release and transport of radionuclides from a repository via the groundwater and direct release pathways provided preliminary estimates of releases to the accessible environment for a 10,000 year simulation time. Latin hypercube sampling of input parameters was used to express results as distributions and to investigate model sensitivities. This methodology demonstration should not be interpreted as an estimate of performance of the proposed repository at Yucca Mountain, Nevada

Assessing the origins, evolution and prospects of the literature on dynamic capabilities: A bibliometric analysis

Directory of Open Access Journals (Sweden)

Gema Albort-Morant

2018-01-01

Full Text Available The purpose of this study is to serve as orientation and guidance to academics that are starting or currently developing their research within the field of dynamic capabilities, in order to enhance their knowledge about which are the key scientific journals, authors and articles shaping this topic. This paper presents a bibliometric analysis on dynamic capabilities, making use of the Web of Science database to perform it. This analysis comprises fundamental issues such as (i the number of studies published per year, (ii the countries with the highest rate of productivity, (iii the most prolific and influential authors, (iv assessment of studies citing dynamic capabilities, and (v the most productive journals on dynamic capabilities and recent studies on this topic. Results reveal an exponential growth in the number of publications on dynamic capabilities for the 2000–2012 period. Although, since 2012 this growth has decelerated, the number of publications on this topic remains noteworthy. This study brings useful information for those academics and practitioners attempting to analyze and deepen within this particular field of research, at the same time that provides some insights concerning the future development and progress of the dynamic capabilities topic in the management, business and economics academic literature.

Assessment of the integration capability of system architectures from a complex and distributed software systems perspective

Science.gov (United States)

Leuchter, S.; Reinert, F.; Müller, W.

2014-06-01

Procurement and design of system architectures capable of network centric operations demand for an assessment scheme in order to compare different alternative realizations. In this contribution an assessment method for system architectures targeted at the C4ISR domain is presented. The method addresses the integration capability of software systems from a complex and distributed software system perspective focusing communication, interfaces and software. The aim is to evaluate the capability to integrate a system or its functions within a system-of-systems network. This method uses approaches from software architecture quality assessment and applies them on the system architecture level. It features a specific goal tree of several dimensions that are relevant for enterprise integration. These dimensions have to be weighed against each other and totalized using methods from the normative decision theory in order to reflect the intention of the particular enterprise integration effort. The indicators and measurements for many of the considered quality features rely on a model based view on systems, networks, and the enterprise. That means it is applicable to System-of-System specifications based on enterprise architectural frameworks relying on defined meta-models or domain ontologies for defining views and viewpoints. In the defense context we use the NATO Architecture Framework (NAF) to ground respective system models. The proposed assessment method allows evaluating and comparing competing system designs regarding their future integration potential. It is a contribution to the system-of-systems engineering methodology.

An assessment system for the system safety engineering capability maturity model in the case of spent fuel reprocessing

International Nuclear Information System (INIS)

Yang Xiaohua; Liu Zhenghai; Liu Zhiming; Wan Yaping; Bai Xiaofeng

2012-01-01

We can improve the processing, the evaluation of capability and promote the user's trust by using system security engineering capability maturity model (SSE-CMM). SSE-CMM is the common method for organizing and implementing safety engineering, and it is a mature method for system safety engineering. Combining capability maturity model (CMM) with total quality management and statistic theory, SSE-CMM turns systems security engineering into a well-defined, mature, measurable, advanced engineering discipline. Lack of domain knowledge, the size of data, the diversity of evidences, the cumbersomeness of processes, and the complexity of matching evidences with problems are the main issues that SSE-CMM assessment has to face. To improve effectively the efficiency of assessment of spent fuel reprocessing system security engineering capability maturity model (SFR-SSE-CMM), in this paper we de- signed an intelligent assessment software based on domain ontology and that uses methods such as ontology, evidence theory, semantic web, intelligent information retrieval and intelligent auto-matching techniques. This software includes four subsystems, which are domain ontology creation and management system, evidence auto collection system, and a problem and evidence matching system. The architecture of the software is divided into five layers: a data layer, an oncology layer, a knowledge layer, a service layer arid a presentation layer. (authors)

Assessment of predictive capabilities for aerodynamic heating in hypersonic flow

Science.gov (United States)

Knight, Doyle; Chazot, Olivier; Austin, Joanna; Badr, Mohammad Ali; Candler, Graham; Celik, Bayram; Rosa, Donato de; Donelli, Raffaele; Komives, Jeffrey; Lani, Andrea; Levin, Deborah; Nompelis, Ioannis; Panesi, Marco; Pezzella, Giuseppe; Reimann, Bodo; Tumuklu, Ozgur; Yuceil, Kemal

2017-04-01

The capability for CFD prediction of hypersonic shock wave laminar boundary layer interaction was assessed for a double wedge model at Mach 7.1 in air and nitrogen at 2.1 MJ/kg and 8 MJ/kg. Simulations were performed by seven research organizations encompassing both Navier-Stokes and Direct Simulation Monte Carlo (DSMC) methods as part of the NATO STO AVT Task Group 205 activity. Comparison of the CFD simulations with experimental heat transfer and schlieren visualization suggest the need for accurate modeling of the tunnel startup process in short-duration hypersonic test facilities, and the importance of fully 3-D simulations of nominally 2-D (i.e., non-axisymmmetric) experimental geometries.

Using HEC-RAS to Enhance Interpretive Capabilities of Geomorphic Assessments

Science.gov (United States)

Keefer, L. L.

2005-12-01

The purpose of a geomorphic assessment is to characterize and evaluate a fluvial system for determining the past watershed and channel conditions, current geomorphic character and potential future channel adjustments. The geomorphic assessment approach utilized by the Illinois State Water Survey assesses channel response to disturbance at multiple temporal and spatial scales to help identify the underlying factors and events which led to the existing channel morphology. This is accomplished through two phases of investigation that involve a historical and physical analysis of the watershed, disturbance history, and field work at increasing levels of detail. To infer future channel adjustments, the geomorphic assessment protocol combines two methods of analyses that are dependent on the quantity and detail of the available data. The first method is the compilation of multiple lines of evidence using qualitative information related to the dominant fluvial environment, channel gradient, stream power thresholds, and channel evolution models. The second method is the use of hydraulic models which provide additional interpretative skills to evaluate potential channel adjustments. The structured data collection framework of the geomorphic assessment approach is used for the development of a HEC-RAS model. The model results are then used as another tool to determine the influence of bridges and control structures on channel stability, stream power profiles to identify potential channel bed degradation zones, and provide data for physically-based bank stability models. This poster will demonstrate the advantages of using a hydraulic model, such as HEC-RAS, to expand the interpretive capabilities of geomorphic assessments. The results from applying this approach will be demonstrated for the Big Creek watershed of the Cache River Basin in southern Illinois.

Assessing COSMO-SkyMed capability for crops identification and monitoring

Science.gov (United States)

Guarini, R.; Dini, L.

2015-12-01

In the last decade, it has been possible to better understand the impact of agricultural human practices on the global environmental change at different spatial (from local to global) and time (from seasonal to decadal) scales. This has been achieved thanks to: big dataset continuously acquired by Earth Observation (EO) satellites; the improved capabilities of remote sensing techniques in extracting valuable information from the EO datasets; the new EO data policy which allowed unrestricted data usage; the net technologies which allowed to quickly and easily share national, international and market-derived information; an increasingly performing computing technology which allows to massively process large amount of data easier and at decreasing costs. To better understand the environmental impacts of agriculture and to monitor the consequences of human agricultural activities on the biosphere, scientists require to better identify crops and monitor crop conditions over time and space. Traditionally, NDVI time series maps derived from optical sensors have been used to this aim. As well-known this important source of information is conditioned by cloud cover. Unlike passive systems, synthetic aperture radar (SAR) ones are almost insensitive to atmospheric influences; thus, they are especially suitable for crop identification and condition monitoring. Among the other SAR systems currently in orbit, the Italian Space Agency (ASI) COSMO Sky-Med® (CSK®) constellation (X-band, frequency 9.6 GHz, wavelength 3.1 cm), especially for its peculiar high revisit capability (up to four images in 16 days with same acquisition geometry) seems to be particular suitable for providing information in addition and/or in alternative to other optical EO systems. To assess the capability of the CSK® constellation in identifying crops and in monitoring crops condition in 2013 ASI started the "AGRICIDOT" project. Some of the main project achievements will be presented at the congress.

Capability Handbook- offline metrology

DEFF Research Database (Denmark)

Islam, Aminul; Marhöfer, David Maximilian; Tosello, Guido

This offline metrological capability handbook has been made in relation to HiMicro Task 3.3. The purpose of this document is to assess the metrological capability of the HiMicro partners and to gather the information of all available metrological instruments in the one single document. It provides...

Treatment planning capability assessment of a beam shaping assembly for accelerator-based BNCT

International Nuclear Information System (INIS)

Herrera, M.S.; González, S.J.; Burlon, A.A.; Minsky, D.M.; Kreiner, A.J.

2011-01-01

Within the frame of an ongoing project to develop a folded Tandem-Electrostatic-Quadrupole accelerator facility for Accelerator-Based Boron Neutron Capture Therapy (AB-BNCT) a theoretical study was performed to assess the treatment planning capability of different configurations of an optimized beam shaping assembly for such a facility. In particular this study aims at evaluating treatment plans for a clinical case of Glioblastoma.

The capabilities and applications of the saphire 5.0 safety assessment software

International Nuclear Information System (INIS)

Russell, K.D.; Wood, S.T.; Kvarfordt, K.J.

1994-01-01

The System Analysis Programs for Hands-on Integrated Reliability Evaluations (SAPHIRE) refers to a suite of computer programs that were developed to create and analyze a probabilistic risk assessment (PRA) of a nuclear power plant. The programs in this suite include: Models and Results Data Base (MAR-D) software, Integrated Reliability and Risk Analysis System (IRRAS) software, System Analysis and Risk Assessment (SARA) software, and Fault tree, Event tree, and Piping and instrumentation diagram (FEP) graphical editor. Each of these programs performs a specific function in taking a PRA from the conceptual state all the way to publication. This paper provides an overview of the features and capabilities provided in version 5.0 of this software system. Some major new features include the ability to store unlimited cut sets, the ability to perform location transformations, the ability to perform seismic analysis, the ability to perform automated rule based recovery analysis and end state cut set partitioning, the ability to perform end state analysis, a new alphanumeric fault tree editor, and a new alphanumeric event tree editor. Many enhancements and improvements to the user interface as well as a significant reduction in the time required to perform an analysis are included in version 5.0. These new features and capabilities provide a powerful set of PC based PRA analysis tools

Assessment of SMART Capability for Multiple Applications

Energy Technology Data Exchange (ETDEWEB)

Kang, Han Ok; Kim, Young In; Kim, Keung Koo; Zee, Sung Kyun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-10-15

Cogeneration has become an attractive for a wide range of non-electric application, including seawater desalination, district heating, district cooling, and other industrial process heat applications. From 2009 to 2012, the SMART Technology Validation and the Standard Design Approval Project was carried out. After one and half years of intensive licensing review, the SDA for SMART was officially issued on July 4{sup th}, 2012 by the NSSC, in compliance with Article 12 of the Nuclear Safety Act. This is the first license for an integral reactor in the world. SMART has beneficial advantages of a reactor safety and economics by an easy implementation of advanced design concepts and technology. Owing to its native characteristics, the SMART can be easily applicable not only to a small scale electricity generation but also to non-electricity applications such as sea water desalination and a district heating. The capability of SMART for the application of sea water desalination and a district heating are assessed through modifying the existing secondary system for electricity generation in this study. SMART can be a good engine for seawater desalination and district heating. Power generation system can be safely and effectively coupled with MEDTVC desalination system using steam transformer. District heating application will increase the cycle efficiency of SMART significantly. Introduction of desalination system doesn't have adverse effect on reactor safety.

Facility Targeting, Protection and Mission Decision Making Using the VISAC Code

Science.gov (United States)

Morris, Robert H.; Sulfredge, C. David

2011-01-01

The Visual Interactive Site Analysis Code (VISAC) has been used by DTRA and several other agencies to aid in targeting facilities and to predict the associated collateral effects for the go, no go mission decision making process. VISAC integrates the three concepts of target geometric modeling, damage assessment capabilities, and an event/fault tree methodology for evaluating accident/incident consequences. It can analyze a variety of accidents/incidents at nuclear or industrial facilities, ranging from simple component sabotage to an attack with military or terrorist weapons. For nuclear facilities, VISAC predicts the facility damage, estimated downtime, amount and timing of any radionuclides released. Used in conjunction with DTRA's HPAC code, VISAC also can analyze transport and dispersion of the radionuclides, levels of contamination of the surrounding area, and the population at risk. VISAC has also been used by the NRC to aid in the development of protective measures for nuclear facilities that may be subjected to attacks by car/truck bombs.

Treatment planning capability assessment of a beam shaping assembly for accelerator-based BNCT.

Science.gov (United States)

Herrera, M S; González, S J; Burlon, A A; Minsky, D M; Kreiner, A J

2011-12-01

Within the frame of an ongoing project to develop a folded Tandem-Electrostatic-Quadrupole accelerator facility for Accelerator-Based Boron Neutron Capture Therapy (AB-BNCT) a theoretical study was performed to assess the treatment planning capability of different configurations of an optimized beam shaping assembly for such a facility. In particular this study aims at evaluating treatment plans for a clinical case of Glioblastoma. Copyright © 2011 Elsevier Ltd. All rights reserved.

Brownfields Assessing Contractor Capabilities for Streamlined Site Investigation: Additional Information Regarding All Appropriate Inquiries and Hiring an Environmental Professional

Science.gov (United States)

This document assists Brownfields grantees and other decision makers as they assess the capabilities of contractors and consultants to determine their qualifications to provide streamlined and innovative strategies for the assessment and and cleanup.

Qualitative assessment of the fission product release capability of ELOCA.Mk5

International Nuclear Information System (INIS)

Klein, M.E.; Carlucci, L.N.; Arimescu, V.I.

1995-01-01

A qualitative assessment of the fission product release capability of the ELOCA.Mk5 computer code was performed by simulating two transients from the sweep-gas experiment, FIO-133. Improved agreement between calculated and experimental trends in release was obtained by applying an interface pressure stress component to the pellet center. As well, results show that the current system for defining the reference temperature distribution for the thermal stress component is not always realistic. These results are being used in the development of a new, mechanistic pellet stress model. (author)

Introduction to the Biomass Project: An Illustration of Evidence-Centered Assessment Design and Delivery Capability. CSE Report.

Science.gov (United States)

Steinberg, Linda S.; Mislevy, Robert J.; Almond, Russell G.; Baird, Andrew B.; Cahallan, Cara; Dibello, Louis V.; Senturk, Deniz; Yan, Duanli; Chernick, Howard; Kindfield, Ann C. H.

This paper describes the design rationale for a prototype of an innovative assessment product, and the process that led to the design. The goals of the Biomass project were to demonstrate: (1) an assessment product designed to serve two new purposes in the transition from high school to college; and (2) the capability needed to produce this kind…

Assessment of U.S. Manufacturing Capability for Next-Generation Wind Turbine Drivetrains

Energy Technology Data Exchange (ETDEWEB)

Cotrell, J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Stelhy, T. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-09-01

Robust U.S. wind turbine manufacturing capabilities and supply chains are important for the United States to reduce the cost of electricity generated from wind turbines. These capabilities and supply chains are also critical to the invention and commercialization of new wind turbine technologies while providing high-quality jobs. The development of advanced drivetrain technologies for windturbine applications is advancing the state of the art for drivetrain design by producing higher capacity and operating reliability than conventional drivetrains. Advanced drivetrain technologies such as medium-speed and direct-drive generators, silicon-carbide (SiC) IGBT-based power electronics, and high torque density speed increasers require different manufacturing and supply chaincapabilities that present both risks and opportunities for U.S. wind turbine manufacturers and the wind industry as a whole. The primary objective of this project is to assess how advanced drivetrain technologies and trends will impact U.S. wind turbine manufacturing and its supply chains. The U.S. Department of Energy and other industry participants will use the information from this study toidentify domestic manufacturing gaps, barriers, and opportunities for developing U.S. wind turbine manufacturing capabilities and supply chains for next-generation drivetrain technologies. This report also includes recommendations for prioritizing technology areas for possible investments by public, private, or nonprofit entities that will reduce the cost of wind-generated electricity. Suchinvestments foster opportunities to invent and commercialize new wind turbine technologies, and provide high-quality jobs in the United States.

People Capability Maturity Model. SM.

Science.gov (United States)

1995-09-01

tailored so it consumes less time and resources than a traditional software process assessment or CMU/SEI-95-MM-02 People Capability Maturity Model...improved reputation or customer loyalty. CMU/SEI-95-MM-02 People Capability Maturity Model ■ L5-17 Coaching Level 5: Optimizing Activity 1...Maturity Model CMU/SEI-95-MM-62 Carnegie-Mellon University Software Engineering Institute DTIC ELECTE OCT 2 7 1995 People Capability Maturity

Capability and quality assessment of rice growing hydric soils in majuli river island, assam, India

Directory of Open Access Journals (Sweden)

Bhaskara Phaneendra Bhaskar

2013-06-01

Full Text Available The  wetland soils in  majuli island is a unique in maintaining rice ecology and geoenvironment in Brahmaputra valley of Assam  due to increasing  rate of  bankline erosion in southern bank  and expansion of channel bars on northern banks. These hydric soils in the subgroups of aquents and aquepts are  saturated throughout year as assessed from depleted matrix with hue 10YR, 2.5Y and 5Y, chroma less than 2, stratified textures, neutral to slightly alkaline reaction, low cation exchange capacity  and poor exchangeable base status. The  assessment of land capability and soil quality  for rice production in   hydric soils  was conducted on twenty four soil mapping units derived from reconnaissance soil survey done on 1:50000 scale.  As per  land capability  assessment, these soils are  good(classII to fairly good(IV for arable use with limitations of low fertility status, moderate to severe wetness and moderate to rapid permeability. The soil quality rating with  multiple variable indicator transform(MVIT technique  of  twenty hydric soil units in active and old floodplains was  medium (35 to 65per cent with six indicators(pH, organic carbon, base saturation, effective rooting depth , structure and texture meeting the thresh hold value  above 65 per cent.  Thirty five  per cent of total area is suitable for rice cultivation as against the current cropped area of 7.2 per cent with potassium and zinc deficiency. The determination of soil quality in relation to land capability was found useful to design best management practices for wetlands in the region that ensure sustainable land use.

Comparing performances of clements, box-cox, Johnson methods with weibull distributions for assessing process capability

Energy Technology Data Exchange (ETDEWEB)

Senvar, O.; Sennaroglu, B.

2016-07-01

This study examines Clements’ Approach (CA), Box-Cox transformation (BCT), and Johnson transformation (JT) methods for process capability assessments through Weibull-distributed data with different parameters to figure out the effects of the tail behaviours on process capability and compares their estimation performances in terms of accuracy and precision. Design/methodology/approach: Usage of process performance index (PPI) Ppu is handled for process capability analysis (PCA) because the comparison issues are performed through generating Weibull data without subgroups. Box plots, descriptive statistics, the root-mean-square deviation (RMSD), which is used as a measure of error, and a radar chart are utilized all together for evaluating the performances of the methods. In addition, the bias of the estimated values is important as the efficiency measured by the mean square error. In this regard, Relative Bias (RB) and the Relative Root Mean Square Error (RRMSE) are also considered. Findings: The results reveal that the performance of a method is dependent on its capability to fit the tail behavior of the Weibull distribution and on targeted values of the PPIs. It is observed that the effect of tail behavior is more significant when the process is more capable. Research limitations/implications: Some other methods such as Weighted Variance method, which also give good results, were also conducted. However, we later realized that it would be confusing in terms of comparison issues between the methods for consistent interpretations... (Author)

Uncertainty quantification's role in modeling and simulation planning, and credibility assessment through the predictive capability maturity model

Energy Technology Data Exchange (ETDEWEB)

Rider, William J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Witkowski, Walter R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mousseau, Vincent Andrew [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2016-04-13

The importance of credible, trustworthy numerical simulations is obvious especially when using the results for making high-consequence decisions. Determining the credibility of such numerical predictions is much more difficult and requires a systematic approach to assessing predictive capability, associated uncertainties and overall confidence in the computational simulation process for the intended use of the model. This process begins with an evaluation of the computational modeling of the identified, important physics of the simulation for its intended use. This is commonly done through a Phenomena Identification Ranking Table (PIRT). Then an assessment of the evidence basis supporting the ability to computationally simulate these physics can be performed using various frameworks such as the Predictive Capability Maturity Model (PCMM). There were several critical activities that follow in the areas of code and solution verification, validation and uncertainty quantification, which will be described in detail in the following sections. Here, we introduce the subject matter for general applications but specifics are given for the failure prediction project. In addition, the first task that must be completed in the verification & validation procedure is to perform a credibility assessment to fully understand the requirements and limitations of the current computational simulation capability for the specific application intended use. The PIRT and PCMM are tools used at Sandia National Laboratories (SNL) to provide a consistent manner to perform such an assessment. Ideally, all stakeholders should be represented and contribute to perform an accurate credibility assessment. PIRTs and PCMMs are both described in brief detail below and the resulting assessments for an example project are given.

An Assessment of the Capability of ICT Education in Bicol University Polangui Campus, Polangui, Albay, Philippines: A Determinant to its Sustainability

Directory of Open Access Journals (Sweden)

Bernardita B Riñon

2013-01-01

Full Text Available The 21st Century poses an urgent need for the integration of ICT in classroom instruction. Education is a lifelong process therefore access to information anytime, anywhere is imperative. We need literates to meet the challenges of illiteracy and poverty and bring about the cost reduction of education,   improve the quality and effectiveness of teaching (wikieducator,n.d.. This paper intends to present the results of an assessment on the capability of ICT education where its sustainability largely depends upon it. Specifically, it aimed to determine the profile of the facilities, faculty readiness in ICT literacy, related researches, budgetary allocation for facilities and linkages with non-government and government agencies likewise the level of capability of ICT education was assessed. Findings revealed that the school has the capability to sustain ICT education. In this study, the researchers arrived at the conclusion that capable and sustainable ICT education would produce ICT literates individuals who would meet the challenges of digital world. Keywords:ICT,Capability,Sustainability, New Literacy, Teachers’ Readiness

An assessment of the real-time application capabilities of the SIFT computer system

Science.gov (United States)

Butler, R. W.

1982-01-01

The real-time capabilities of the SIFT computer system, a highly reliable multicomputer architecture developed to support the flight controls of a relaxed static stability aircraft, are discussed. The SIFT computer system was designed to meet extremely high reliability requirements and to facilitate a formal proof of its correctness. Although SIFT represents a significant achievement in fault-tolerant system research it presents an unusual and restrictive interface to its users. The characteristics of the user interface and its impact on application system design are assessed.

Lawrence Livermore National Laboratory Emergency Response Capability Baseline Needs Assessment Requirement Document

Energy Technology Data Exchange (ETDEWEB)

Sharry, J A

2009-12-30

This revision of the LLNL Fire Protection Baseline Needs Assessment (BNA) was prepared by John A. Sharry, LLNL Fire Marshal and LLNL Division Leader for Fire Protection and reviewed by Martin Gresho, Sandia/CA Fire Marshal. The document follows and expands upon the format and contents of the DOE Model Fire Protection Baseline Capabilities Assessment document contained on the DOE Fire Protection Web Site, but only address emergency response. The original LLNL BNA was created on April 23, 1997 as a means of collecting all requirements concerning emergency response capabilities at LLNL (including response to emergencies at Sandia/CA) into one BNA document. The original BNA documented the basis for emergency response, emergency personnel staffing, and emergency response equipment over the years. The BNA has been updated and reissued five times since in 1998, 1999, 2000, 2002, and 2004. A significant format change was performed in the 2004 update of the BNA in that it was 'zero based.' Starting with the requirement documents, the 2004 BNA evaluated the requirements, and determined minimum needs without regard to previous evaluations. This 2010 update maintains the same basic format and requirements as the 2004 BNA. In this 2010 BNA, as in the previous BNA, the document has been intentionally divided into two separate documents - the needs assessment (1) and the compliance assessment (2). The needs assessment will be referred to as the BNA and the compliance assessment will be referred to as the BNA Compliance Assessment. The primary driver for separation is that the needs assessment identifies the detailed applicable regulations (primarily NFPA Standards) for emergency response capabilities based on the hazards present at LLNL and Sandia/CA and the geographical location of the facilities. The needs assessment also identifies areas where the modification of the requirements in the applicable NFPA standards is appropriate, due to the improved fire protection

Technological Innovation Capabilities and Firm Performance

OpenAIRE

Richard C.M. Yam; William Lo; Esther P.Y. Tang; Antonio; K.W. Lau

2010-01-01

Technological innovation capability (TIC) is defined as a comprehensive set of characteristics of a firm that facilities and supports its technological innovation strategies. An audit to evaluate the TICs of a firm may trigger improvement in its future practices. Such an audit can be used by the firm for self assessment or third-party independent assessment to identify problems of its capability status. This paper attempts to develop such an auditing framework that can...

Integrating measuring uncertainty of tactile and optical coordinate measuring machines in the process capability assessment of micro injection moulding

DEFF Research Database (Denmark)

Tosello, Guido; Hansen, Hans Nørgaard; Gasparin, Stefania

2010-01-01

Process capability of micro injection moulding was investigated in this paper by calculating the Cp and Cpk statistics. Uncertainty of both optical and tactile measuring systems employed in the quality control of micro injection moulded products was assessed and compared with the specified...... tolerances. Limits in terms of manufacturing process capability as well as of suitability of such measuring systems when employed for micro production inspection were quantitatively determined....

Assessment of the analytical capabilities of inductively coupled plasma-mass spectrometry

Science.gov (United States)

Taylor, Howard E.; Garbarino, John R.

1988-01-01

A thorough assessment of the analytical capabilities of inductively coupled plasma-mass spectrometry was conducted for selected analytes of importance in water quality applications and hydrologic research. A multielement calibration curve technique was designed to produce accurate and precise results in analysis times of approximately one minute. The suite of elements included Al, As, B, Ba, Be, Cd, Co, Cr, Cu, Hg, Li, Mn, Mo, Ni, Pb, Se, Sr, V, and Zn. The effects of sample matrix composition on the accuracy of the determinations showed that matrix elements (such as Na, Ca, Mg, and K) that may be present in natural water samples at concentration levels greater than 50 mg/L resulted in as much as a 10% suppression in ion current for analyte elements. Operational detection limits are presented.

Brownfields Assessing Contractor Capabilities for Streamlined Site Investigations -- Additional Information Regarding All Appropriate Inquiries and Hiring an Environmental Professional (November 2006)

Science.gov (United States)

Guidance for Brownfields grantees and other decision makers to assess the capabilities of contractors and consultants to determine their qualifications to provide streamlined and innovative strategies for the assessment and cleanup of brownfields.

A survey and assessment of the capabilities of Cubesats for Earth observation

Science.gov (United States)

Selva, Daniel; Krejci, David

2012-05-01

In less than a decade, Cubesats have evolved from purely educational tools to a standard platform for technology demonstration and scientific instrumentation. The use of COTS (Commercial-Off-The-Shelf) components and the ongoing miniaturization of several technologies have already led to scattered instances of missions with promising scientific value. Furthermore, advantages in terms of development cost and development time with respect to larger satellites, as well as the possibility of launching several dozens of Cubesats with a single rocket launch, have brought forth the potential for radically new mission architectures consisting of very large constellations or clusters of Cubesats. These architectures promise to combine the temporal resolution of GEO missions with the spatial resolution of LEO missions, thus breaking a traditional trade-off in Earth observation mission design. This paper assesses the current capabilities of Cubesats with respect to potential employment in Earth observation missions. A thorough review of Cubesat bus technology capabilities is performed, identifying potential limitations and their implications on 17 different Earth observation payload technologies. These results are matched to an exhaustive review of scientific requirements in the field of Earth observation, assessing the possibilities of Cubesats to cope with the requirements set for each one of 21 measurement categories. Based on this review, several Earth observation measurements are identified that can potentially be compatible with the current state-of-the-art of Cubesat technology although some of them have actually never been addressed by any Cubesat mission. Simultaneously, other measurements are identified which are unlikely to be performed by Cubesats in the next few years due to insuperable constraints. Ultimately, this paper is intended to supply a box of ideas for universities to design future Cubesat missions with high scientific payoff.

Assessment of CFD Capability for Hypersonic Shock Wave Laminar Boundary Layer Interactions

Directory of Open Access Journals (Sweden)

Mehrnaz Rouhi Youssefi

2017-04-01

Full Text Available The goal of this study is to assess CFD capability for the prediction of shock wave laminar boundary layer interactions at hypersonic velocities. More specifically, the flow field over a double-cone configuration is simulated using both perfect gas and non-equilibrium Navier–Stokes models. Computations are compared with recent experimental data obtained from measurements conducted in the LENS XX (Large Energy National Shock Expansion Tunnel Version 2 at the Calspan University of Buffalo Research Center (CUBRC. Four separate cases of freestream conditions are simulated to examine the models for a range of stagnation enthalpies from 5.44 MJ/kg to 21.77 MJ/kg and Mach numbers from 10.9 to 12.82.

Earth Science Capability Demonstration Project

Science.gov (United States)

Cobleigh, Brent

2006-01-01

A viewgraph presentation reviewing the Earth Science Capability Demonstration Project is shown. The contents include: 1) ESCD Project; 2) Available Flight Assets; 3) Ikhana Procurement; 4) GCS Layout; 5) Baseline Predator B Architecture; 6) Ikhana Architecture; 7) UAV Capability Assessment; 8) The Big Picture; 9) NASA/NOAA UAV Demo (5/05 to 9/05); 10) NASA/USFS Western States Fire Mission (8/06); and 11) Suborbital Telepresence.

A framework study on assessment of mass customization capabilities

DEFF Research Database (Denmark)

Nielsen, Kjeld; Brunø, Thomas Ditlev; Jørgensen, Kaj Asbjørn

2012-01-01

Much research has been done to assist industries to move from mass production to mass customization. Salvador F., et al. made it clear in the article “Cracking the code of Mass Customization”, that becoming a Mass Customizer is not a single step quick fix, but requires 3 fundamental capabilities....... In that article it is proposed that these three capabilities are evaluated in a continuum model as an illustration of a company’s status of mass customization. This paper will introduce the neccesarity for a framework for measuring a company’s performance as a mass customizer....

National Research Council Dialogue to Assess Progress on NASA's Advanced Modeling, Simulation and Analysis Capability and Systems Engineering Capability Roadmap Development

Science.gov (United States)

Aikins, Jan

2005-01-01

Contents include the following: General Background and Introduction of Capability Roadmaps. Agency Objective. Strategic Planning Transformation. Advanced Planning Organizational Roles. Public Involvement in Strategic Planning. Strategic Roadmaps and Schedule. Capability Roadmaps and Schedule. Purpose of NRC Review. Capability Roadmap Development (Progress to Date).

A Demonstration of the System Assessment Capability (SAC) Rev. 1 Software for the Hanford Remediation Assessment Project

International Nuclear Information System (INIS)

Eslinger, Paul W.; Kincaid, Charles T.; Nichols, William E.; Wurstner, Signe K.

2006-01-01

The System Assessment Capability (SAC) is a suite of interrelated computer codes that provides the capability to conduct large-scale environmental assessments on the Hanford Site. Developed by Pacific Northwest National Laboratory for the Department of Energy, SAC models the fate and transport of radioactive and chemical contaminants, starting with the inventory of those contaminants in waste sites, simulating transport through the environment, and continuing on through impacts to the environment and humans. Separate modules in the SAC address inventory, release from waste forms, water flow and mass transport in the vadose zone, water flow and mass transport in the groundwater, water flow and mass transport in the Columbia River, air transport, and human and ecological impacts. The SAC supports deterministic analyses as well as stochastic analyses using a Monte Carlo approach, enabling SAC users to examine the effect of uncertainties in a number of key parameters. The initial assessment performed with the SAC software identified a number of areas where both the software and the analysis approach could be improved. Since that time the following six major software upgrades have been made: (1) An air pathway model was added to support all-pathway analyses. (2) Models for releases from glass waste forms, buried graphite reactor cores, and buried naval reactor compartments were added. (3) An air-water dual-phase model was added to more accurately track the movement of volatile contaminants in the vadose zone. (4) The ability to run analyses was extended from 1,000 years to 10,000 years or longer after site closure. (5) The vadose zone flow and transport model was upgraded to support two-dimensional or three-dimensional analyses. (6) The ecological model and human risk models were upgraded so the concentrations of contaminants in food products consumed by humans are produced by the ecological model. This report documents the functions in the SAC software and provides a

A Demonstration of the System Assessment Capability (SAC) Rev. 1 Software for the Hanford Remediation Assessment Project

Energy Technology Data Exchange (ETDEWEB)

Eslinger, Paul W.; Kincaid, Charles T.; Nichols, William E.; Wurstner, Signe K.

2006-11-06

The System Assessment Capability (SAC) is a suite of interrelated computer codes that provides the capability to conduct large-scale environmental assessments on the Hanford Site. Developed by Pacific Northwest National Laboratory for the Department of Energy, SAC models the fate and transport of radioactive and chemical contaminants, starting with the inventory of those contaminants in waste sites, simulating transport through the environment, and continuing on through impacts to the environment and humans. Separate modules in the SAC address inventory, release from waste forms, water flow and mass transport in the vadose zone, water flow and mass transport in the groundwater, water flow and mass transport in the Columbia River, air transport, and human and ecological impacts. The SAC supports deterministic analyses as well as stochastic analyses using a Monte Carlo approach, enabling SAC users to examine the effect of uncertainties in a number of key parameters. The initial assessment performed with the SAC software identified a number of areas where both the software and the analysis approach could be improved. Since that time the following six major software upgrades have been made: (1) An air pathway model was added to support all-pathway analyses. (2) Models for releases from glass waste forms, buried graphite reactor cores, and buried naval reactor compartments were added. (3) An air-water dual-phase model was added to more accurately track the movement of volatile contaminants in the vadose zone. (4) The ability to run analyses was extended from 1,000 years to 10,000 years or longer after site closure. (5) The vadose zone flow and transport model was upgraded to support two-dimensional or three-dimensional analyses. (6) The ecological model and human risk models were upgraded so the concentrations of contaminants in food products consumed by humans are produced by the ecological model. This report documents the functions in the SAC software and provides a

Comparing performances of clements, box-cox, Johnson methods with weibull distributions for assessing process capability

Directory of Open Access Journals (Sweden)

Ozlem Senvar

2016-08-01

Full Text Available Purpose: This study examines Clements’ Approach (CA, Box-Cox transformation (BCT, and Johnson transformation (JT methods for process capability assessments through Weibull-distributed data with different parameters to figure out the effects of the tail behaviours on process capability and compares their estimation performances in terms of accuracy and precision. Design/methodology/approach: Usage of process performance index (PPI Ppu is handled for process capability analysis (PCA because the comparison issues are performed through generating Weibull data without subgroups. Box plots, descriptive statistics, the root-mean-square deviation (RMSD, which is used as a measure of error, and a radar chart are utilized all together for evaluating the performances of the methods. In addition, the bias of the estimated values is important as the efficiency measured by the mean square error. In this regard, Relative Bias (RB and the Relative Root Mean Square Error (RRMSE are also considered. Findings: The results reveal that the performance of a method is dependent on its capability to fit the tail behavior of the Weibull distribution and on targeted values of the PPIs. It is observed that the effect of tail behavior is more significant when the process is more capable. Research limitations/implications: Some other methods such as Weighted Variance method, which also give good results, were also conducted. However, we later realized that it would be confusing in terms of comparison issues between the methods for consistent interpretations. Practical implications: Weibull distribution covers a wide class of non-normal processes due to its capability to yield a variety of distinct curves based on its parameters. Weibull distributions are known to have significantly different tail behaviors, which greatly affects the process capability. In quality and reliability applications, they are widely used for the analyses of failure data in order to understand how

Establishing Sustainable Nuclear Education: Education Capability Assessment and Planning (ECAP) Assist Mission

International Nuclear Information System (INIS)

Ugbor, U.; Peddicord, K.; Dies, J.; Philip, B.; Artisyuk, V.

2016-01-01

Full text: The development of nuclear education, science and technology programmes is affected by the national context including national needs and capacities. The role and expectations for nuclear education and training might be different in technically matured countries, from countries where the technology is emerging. In this regard, particularly in developing countries, there is a need to balance nuclear education and training between immediate critical issues of radiation safety or human health and longer-term priorities in agriculture or industry. These priorities may or may not include the nuclear energy option. This paper shows how the Education Capability Assessment and Planning (ECAP) Assist Mission can contribute towards establishing sustainable nuclear education, including highlighting the various activities of each phase of the ECAP Process. (author

European TBM for ITER: Structural material assessment and breeding capability - Comparative analysis

International Nuclear Information System (INIS)

Herreras, Y.; Perlado, J.M.; Ibarra, A.

2007-01-01

Full text of publication follows: The ITER European Party is currently developing for DEMO reactor specifications two breeding blanket concepts: the Helium-Cooled Lithium-Lead blanket (HCLL), using a liquid breeder; and the Helium-Cooled Pebble-Bed blanket (HCPB), using a lithiated solid breeder. These two research lines are expected to be tested in ITER as Test Blanket Modules (TBM), in order to demonstrate their safety, economical and environmental suitability. In this sense, structural material activation and breeding blanket capability represent two major challenges. This paper presents new calculations regarding neutronic irradiation inside the ITER Vacuum Vessel. In particular, results are focused on the irradiation affecting the equatorial ports, where the TBM will be located for testing. The methodology employed mainly consists in calculating the neutronic irradiation levels at the required locations with the transport code MCNP, where the input geometry has been previously designed with the program CATIA V5. The main structural materials proposed for the European Test blanket Modules are selected in order to carry out a comparative analysis in safety terms: material activation and basic parameters for damage analysis are evaluated with the code ACAB, based on the neutronic irradiation results mentioned above. Finally, the breeding blanket capability is assessed for both breeding blanket concepts; the results are compared considering the choice of the structural material. (authors)

Using the virtual reality device Oculus Rift for neuropsychological assessment of visual processing capabilities.

Science.gov (United States)

Foerster, Rebecca M; Poth, Christian H; Behler, Christian; Botsch, Mario; Schneider, Werner X

2016-11-21

Neuropsychological assessment of human visual processing capabilities strongly depends on visual testing conditions including room lighting, stimuli, and viewing-distance. This limits standardization, threatens reliability, and prevents the assessment of core visual functions such as visual processing speed. Increasingly available virtual reality devices allow to address these problems. One such device is the portable, light-weight, and easy-to-use Oculus Rift. It is head-mounted and covers the entire visual field, thereby shielding and standardizing the visual stimulation. A fundamental prerequisite to use Oculus Rift for neuropsychological assessment is sufficient test-retest reliability. Here, we compare the test-retest reliabilities of Bundesen's visual processing components (visual processing speed, threshold of conscious perception, capacity of visual working memory) as measured with Oculus Rift and a standard CRT computer screen. Our results show that Oculus Rift allows to measure the processing components as reliably as the standard CRT. This means that Oculus Rift is applicable for standardized and reliable assessment and diagnosis of elementary cognitive functions in laboratory and clinical settings. Oculus Rift thus provides the opportunity to compare visual processing components between individuals and institutions and to establish statistical norm distributions.

Assessing the relationship between youth capabilities and food ...

African Journals Online (AJOL)

2015-07-04

Jul 4, 2015 ... The links between water and food, in particular in the focus area for this study, ... in decision-making processes as some members are more involved than .... tionings that are necessary for human systems to be capable of managing the .... The research methods utilised in this paper include mixed methods.

Wearable accelerometry-based technology capable of assessing functional activities in neurological populations in community settings: a systematic review.

Science.gov (United States)

Steins, Dax; Dawes, Helen; Esser, Patrick; Collett, Johnny

2014-03-13

Integrating rehabilitation services through wearable systems has the potential to accurately assess the type, intensity, duration, and quality of movement necessary for procuring key outcome measures. This review aims to explore wearable accelerometry-based technology (ABT) capable of assessing mobility-related functional activities intended for rehabilitation purposes in community settings for neurological populations. In this review, we focus on the accuracy of ABT-based methods, types of outcome measures, and the implementation of ABT in non-clinical settings for rehabilitation purposes. Cochrane, PubMed, Web of Knowledge, EMBASE, and IEEE Xplore. The search strategy covered three main areas, namely wearable technology, rehabilitation, and setting. Potentially relevant studies were categorized as systems either evaluating methods or outcome parameters. Methodological qualities of studies were assessed by two customized checklists, depending on their categorization and rated independently by three blinded reviewers. Twelve studies involving ABT met the eligibility criteria, of which three studies were identified as having implemented ABT for rehabilitation purposes in non-clinical settings. From the twelve studies, seven studies achieved high methodological quality scores. These studies were not only capable of assessing the type, quantity, and quality measures of functional activities, but could also distinguish healthy from non-healthy subjects and/or address disease severity levels. While many studies support ABT's potential for telerehabilitation, few actually utilized it to assess mobility-related functional activities outside laboratory settings. To generate more appropriate outcome measures, there is a clear need to translate research findings and novel methods into practice.

Learning Capability and Business Performance: A Non-Financial and Financial Assessment

Science.gov (United States)

Ma Prieto, Isabel; Revilla, Elena

2006-01-01

Purpose: There has been little research that includes reliable deductions about the positive influence of learning capability on business performance. For this reason, the main objective of the present study is to empirically explore the link between learning capability in organizations and business performance evaluated in both financial and…

Organizational Learning Capability: An Example of University Hospital

Directory of Open Access Journals (Sweden)

Yasin UZUNTARLA

2015-06-01

Full Text Available In health care institutions aiming healthy society by the way protecting and promoting human health, reaching information has a vital importance. This descriptive research purposed an evaluation of organizational learning capability of 396 employees working in Gülhane Military Medical Academy Hospital. A questionnaire including socio-demographic characteristics was used along with Organizational Learning Capability scale designed by Ricardo CHIVA and His Friends. Data acquired was analyzed with SPSS 15.0 program. Participants’ Organizational Learning Capability and its subscales means were assessed in terms of their sociodemographic characteristics. Assessing participants’ answers in terms of 5 subscales which are experimentation, risk taking, interaction with the external environment, dialogue and participatory decision-making; for education level and professional groups, statistical significant differences was found between Organizational Learning Capability and its subscales means.

Assessment of CFD capability for prediction of hypersonic shock interactions

Science.gov (United States)

Knight, Doyle; Longo, José; Drikakis, Dimitris; Gaitonde, Datta; Lani, Andrea; Nompelis, Ioannis; Reimann, Bodo; Walpot, Louis

2012-01-01

The aerothermodynamic loadings associated with shock wave boundary layer interactions (shock interactions) must be carefully considered in the design of hypersonic air vehicles. The capability of Computational Fluid Dynamics (CFD) software to accurately predict hypersonic shock wave laminar boundary layer interactions is examined. A series of independent computations performed by researchers in the US and Europe are presented for two generic configurations (double cone and cylinder) and compared with experimental data. The results illustrate the current capabilities and limitations of modern CFD methods for these flows.

Capitalizing on capabilities.

Science.gov (United States)

Ulrich, Dave; Smallwood, Norm

2004-06-01

By making the most of organizational capabilities--employees' collective skills and fields of expertise--you can dramatically improve your company's market value. Although there is no magic list of proficiencies that every organization needs in order to succeed, the authors identify 11 intangible assets that well-managed companies tend to have: talent, speed, shared mind-set and coherent brand identity, accountability, collaboration, learning, leadership, customer connectivity, strategic unity, innovation, and efficiency. Such companies typically excel in only three of these capabilities while maintaining industry parity in the other areas. Organizations that fall below the norm in any of the 11 are likely candidates for dysfunction and competitive disadvantage. So you can determine how your company fares in these categories (or others, if the generic list doesn't suit your needs), the authors explain how to conduct a "capabilities audit," describing in particular the experiences and findings of two companies that recently performed such audits. In addition to highlighting which intangible assets are most important given the organization's history and strategy, this exercise will gauge how well your company delivers on its capabilities and will guide you in developing an action plan for improvement. A capabilities audit can work for an entire organization, a business unit, or a region--indeed, for any part of a company that has a strategy to generate financial or customer-related results. It enables executives to assess overall company strengths and weaknesses, senior leaders to define strategy, midlevel managers to execute strategy, and frontline leaders to achieve tactical results. In short, it helps turn intangible assets into concrete strengths.

Developing the P2/6 methodology [to assess the security capability of modern distributed generation

Energy Technology Data Exchange (ETDEWEB)

Allan, Ron; Strbac, Goran; Djapic, Predrag; Jarrett, Keith [Manchester Univ. Inst. of Science and Technology, Manchester (United Kingdom)

2004-04-29

The main objective of the project was to use the methodology developed in the previous Methodology project (ETSU/FES Project K/EL/00287) to assess the security capability of modern distributed generation in order to review Table 2 and related text of Engineering Recommendation P2/5, and to propose information and results that could be used to create a new P2/6 that takes into account modern types of generating units; unit numbers; unit availabilities; and capacities. Technical issues raised in the previous study but held over until this project include: Treatment of single unit generation systems; Effect of shape of load duration curves; Persistence of intermittent generation, T{sub m}; Time resolution of intermittent generation output profiles; Ride-through capability; Risk to loss of supply. Three main ways of implementing the methodology were recommended: Look-up table(s), Graphical, and Computer program. The specification for the computer program was to produce a simple spreadsheet application package that an engineer with a reasonably knowledge of the approach could use. This prototype package has been developed in conjunction with Workstream 3. Its objective is to calculate the capability contribution to security of supply from distributed generation connected to a particular demand group. The application has been developed using Microsoft Excel and Visual Basic for Applications. New Tables for inclusion in P2/6 are included. (UK)

Evaluation of a Continuing Education Training on Client Financial Capability

Science.gov (United States)

Frey, Jodi Jacobson; Svoboda, Deborah; Sander, Rebecca L.; Osteen, Philip J.; Callahan, Christine; Elkinson, Audrey

2015-01-01

The researchers conducted an evaluation study assessing outcomes among 37 social workers who completed a continuing education course on financial capability and working with clients. Key constructs assessed included participants' attitudes about financial capability, self-efficacy to provide services, organizational barriers, and basic financial…

Baseline Assessment and Prioritization Framework for IVHM Integrity Assurance Enabling Capabilities

Science.gov (United States)

Cooper, Eric G.; DiVito, Benedetto L.; Jacklin, Stephen A.; Miner, Paul S.

2009-01-01

Fundamental to vehicle health management is the deployment of systems incorporating advanced technologies for predicting and detecting anomalous conditions in highly complex and integrated environments. Integrated structural integrity health monitoring, statistical algorithms for detection, estimation, prediction, and fusion, and diagnosis supporting adaptive control are examples of advanced technologies that present considerable verification and validation challenges. These systems necessitate interactions between physical and software-based systems that are highly networked with sensing and actuation subsystems, and incorporate technologies that are, in many respects, different from those employed in civil aviation today. A formidable barrier to deploying these advanced technologies in civil aviation is the lack of enabling verification and validation tools, methods, and technologies. The development of new verification and validation capabilities will not only enable the fielding of advanced vehicle health management systems, but will also provide new assurance capabilities for verification and validation of current generation aviation software which has been implicated in anomalous in-flight behavior. This paper describes the research focused on enabling capabilities for verification and validation underway within NASA s Integrated Vehicle Health Management project, discusses the state of the art of these capabilities, and includes a framework for prioritizing activities.

Materials Capability Review Los Alamos National Laboratory May 4-7, 2009

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoniette J [Los Alamos National Laboratory

2009-01-01

Los Alamos National Laboratory (LANL) uses external peer review to measure and continuously improve the quality of its science, technology and engineering (STE). LANL uses capability reviews to assess the STE quality and institutional integration and to advise Laboratory Management on the current and future health of the STE. Capability reviews address the STE integration that LANL uses to meet mission requirements. STE capabilities are define to cut across directorates providing a more holistic view of the STE quality, integration to achieve mission requirements, and mission relevance. The scope of these capabilities necessitate that there will be significant overlap in technical areas covered by capability reviews (e.g ., materials research and weapons science and engineering). In addition, LANL staff may be reviewed in different capability reviews because of their varied assignments and expertise. LANL plans to perform a complete review of the Laboratory's STE capabilities (hence staff) in a three-year cycle. The principal product of an external review is a report that includes the review committee's assessments, commendations, and recommendations for STE. The Capability Review Committees serve a dual role of providing assessment of the Laboratory's technical contributions and integration towards its missions and providing advice to Laboratory Management. The assessments and advice are documented in reports prepared by the Capability Review Committees that are delivered to the Director and to the Principal Associate Director for Science, Technology and Engineering (PADSTE). This report will be used by Laboratory Management for STE assessment and planning. The report is also provided to the Department of Energy (DOE) as part of LANL's Annual Performance Plan and to the Los Alamos National Security (LANS) LLC's Science and Technology Committee (STC) as part of its responsibilities to the LANS Board of Governors. LANL has defined fourteen

State-level emergency preparedness and response capabilities.

Science.gov (United States)

Watkins, Sharon M; Perrotta, Dennis M; Stanbury, Martha; Heumann, Michael; Anderson, Henry; Simms, Erin; Huang, Monica

2011-03-01

Prior assessments of public health readiness had identified gaps in radiation preparedness. In recent years, preparedness planning has involved an "all-hazards" approach. Current assessment of the national status related to radiation public health emergency preparedness capabilities at the state and local health department levels was needed. A survey of state health departments related to radiation readiness was undertaken in 2010 by the Council of State and Territorial Epidemiologists (CSTE). States with nuclear power plants were instructed to consider their responses exclusive of capabilities and resources related to the plants given that the emergency response plans for nuclear power plants are specific and unique. Thirty-eight (76%) state health departments responded to the survey, including 26 of the 31 states with nuclear power plants. Specific strengths noted at the state level included that the majority of states had a written radiation response plan and most plans include a detailed section for communications issues during a radiation emergency. In addition, more than half of the states indicated that their relationship with federal partners is sufficient to provide resources for radiation emergencies, indicating the importance states placed on federal resources and expertise. Specific weaknesses are discussed and include that most states had completed little to no planning for public health surveillance to assess potential human health impacts of a radiation event; less than half had written plans to address exposure assessment, environmental sampling, human specimen collection and analysis, and human health assessment. Few reported having sufficient resources to do public health surveillance, radiation exposure assessment, laboratory functions and other capabilities. Levels of planning, resources and partnerships varied among states, those with nuclear power plants were better prepared. Gaps were evident in all states; however and additional training and

Non-small cell carcinoma: Comparison of postoperative intra- and extrathoracic recurrence assessment capability of qualitatively and/or quantitatively assessed FDG-PET/CT and standard radiological examinations

Energy Technology Data Exchange (ETDEWEB)

Onishi, Yumiko, E-mail: onitan@med.kobe-u.ac.jp [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan); Ohno, Yoshiharu, E-mail: yosirad@kobe-u.ac.jp [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan); Koyama, Hisanobu; Nogami, Munenobu; Takenaka, Daisuke [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan); Matsumoto, Keiko [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan); Department of Radiology, Yamanashi University, Shimokato, Yamanashi (Japan); Yoshikawa, Takeshi; Matsumoto, Sumiaki [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan); Maniwa, Yoshimasa [Division of Thoracic Surgery, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Nishimura, Yoshihiro [Division of Respiratory Medicine, Department of Internal Medicine, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Sugimura, Kazuro [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe 650-0017, Hyogo (Japan)

2011-09-15

Purpose: The purpose of this study was to compare the capability of integrated FDG-PET/CT for assessment of postoperative intra- and extrathoracic recurrence in non-small cell lung cancer (NSCLC) patients with that of standard radiological examinations. Materials and methods: A total of 121 consecutive pathologically diagnosed NSCLC patients (80 males, 41 females; mean age, 71 years) underwent pathologically and surgically confirmed complete resection, followed by prospective integrated FDG-PET/CT and standard radiological examinations. Final diagnosis of recurrence was based on the results of more than 12 months of follow-up and/or pathological examinations. The probability of recurrence was assessed with either method for each patient by using 5-point visual scoring system, and final diagnosis was made by consensus between two readers. ROC analysis was used to compare the capability of the two methods for assessment of postoperative recurrence on a per-patient basis. The ROC-based positive test was used to determine optimal cut-off value for FDG uptake measurement at a site suspected on the basis of qualitatively assessed PET/CT. Finally, sensitivities, specificities and accuracies of all methods were compared by means of McNemar's test. Results: Areas under the curve of qualitatively assessed PET/CT and standard radiological examinations showed no significant differences (p > 0.05). At an optimal cut-off value of 2.5, specificity and accuracy of quantitatively and qualitatively assessed PET/CT were significantly higher than those of qualitatively assessed PET/CT and standard radiological examinations (p < 0.05). Conclusion: Accuracy of assessment of postoperative intra- and extrathoracic recurrence in NSCLC patients by qualitative and/or quantitative FDG-PET/CT is equivalent to or higher than that by standard radiological examinations.

Non-small cell carcinoma: Comparison of postoperative intra- and extrathoracic recurrence assessment capability of qualitatively and/or quantitatively assessed FDG-PET/CT and standard radiological examinations

International Nuclear Information System (INIS)

Onishi, Yumiko; Ohno, Yoshiharu; Koyama, Hisanobu; Nogami, Munenobu; Takenaka, Daisuke; Matsumoto, Keiko; Yoshikawa, Takeshi; Matsumoto, Sumiaki; Maniwa, Yoshimasa; Nishimura, Yoshihiro; Sugimura, Kazuro

2011-01-01

Purpose: The purpose of this study was to compare the capability of integrated FDG-PET/CT for assessment of postoperative intra- and extrathoracic recurrence in non-small cell lung cancer (NSCLC) patients with that of standard radiological examinations. Materials and methods: A total of 121 consecutive pathologically diagnosed NSCLC patients (80 males, 41 females; mean age, 71 years) underwent pathologically and surgically confirmed complete resection, followed by prospective integrated FDG-PET/CT and standard radiological examinations. Final diagnosis of recurrence was based on the results of more than 12 months of follow-up and/or pathological examinations. The probability of recurrence was assessed with either method for each patient by using 5-point visual scoring system, and final diagnosis was made by consensus between two readers. ROC analysis was used to compare the capability of the two methods for assessment of postoperative recurrence on a per-patient basis. The ROC-based positive test was used to determine optimal cut-off value for FDG uptake measurement at a site suspected on the basis of qualitatively assessed PET/CT. Finally, sensitivities, specificities and accuracies of all methods were compared by means of McNemar's test. Results: Areas under the curve of qualitatively assessed PET/CT and standard radiological examinations showed no significant differences (p > 0.05). At an optimal cut-off value of 2.5, specificity and accuracy of quantitatively and qualitatively assessed PET/CT were significantly higher than those of qualitatively assessed PET/CT and standard radiological examinations (p < 0.05). Conclusion: Accuracy of assessment of postoperative intra- and extrathoracic recurrence in NSCLC patients by qualitative and/or quantitative FDG-PET/CT is equivalent to or higher than that by standard radiological examinations.

Capability of abdominal 320-detector row CT for small vasculature assessment compared with that of 64-detector row CT

Energy Technology Data Exchange (ETDEWEB)

Kitajima, Kazuhiro, E-mail: kitajima@med.kobe-u.ac.jp [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2, Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Maeda, Tetsuo; Ohno, Yoshiharu [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2, Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Division of Radiology, Kobe University Hospital, Kobe (Japan); Yoshikawa, Takeshi [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2, Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Konishi, Minoru [Division of Radiology, Kobe University Hospital, Kobe (Japan); Kanda, Tomonori; Onishi, Yumiko; Matsumoto, Keiko; Koyama, Hisanobu; Takenaka, Daisuke; Sugimura, Kazuro [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2, Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan)

2011-11-15

Objective: To compare the capability of 320-detector row CT (area-detector CT: ADCT) with step-and-shoot scan protocol for small abdominal vasculature assessment with that of 64-detector row CT with helical scan protocol. Materials and methods: Total of 60 patients underwent contrast-enhanced abdominal CT for preoperative assessment. Of all, 30 suspected to have lung cancer underwent ADCT using step-and-shoot scan protocol. The other 30 suspected to have renal cell carcinoma underwent 64-MDCT using helical scan protocol. Two experienced radiologists independently assessed inferior epigastric, hepatic subsegmental (in the segment 8), mesenteric marginal (Griffith point) and inferior phrenic arteries by using 5-point visual scoring systems. Kappa analysis was used for evaluation of interobserver agreement. To compare the visualization capability of the two systems, the Mann-Whitney U-test was used to compare the scores for each of the arteries. Results: Overall interobserver agreements for both systems were almost perfect ({kappa} > 0.80). Visualization scores for inferior epigastric and mesenteric arteries were significantly higher for ADCT than for 64-detector row CT (p < 0.05). No significant difference was found for hepatic subsegmental and inferior phrenic arteries. Conclusion: Small abdominal vasculature assessment by ADCT with step-and-shoot scan protocol is potentially equal to or better than that by 64-detector row CT with helical scan protocol.

Capability of abdominal 320-detector row CT for small vasculature assessment compared with that of 64-detector row CT

International Nuclear Information System (INIS)

Kitajima, Kazuhiro; Maeda, Tetsuo; Ohno, Yoshiharu; Yoshikawa, Takeshi; Konishi, Minoru; Kanda, Tomonori; Onishi, Yumiko; Matsumoto, Keiko; Koyama, Hisanobu; Takenaka, Daisuke; Sugimura, Kazuro

2011-01-01

Objective: To compare the capability of 320-detector row CT (area-detector CT: ADCT) with step-and-shoot scan protocol for small abdominal vasculature assessment with that of 64-detector row CT with helical scan protocol. Materials and methods: Total of 60 patients underwent contrast-enhanced abdominal CT for preoperative assessment. Of all, 30 suspected to have lung cancer underwent ADCT using step-and-shoot scan protocol. The other 30 suspected to have renal cell carcinoma underwent 64-MDCT using helical scan protocol. Two experienced radiologists independently assessed inferior epigastric, hepatic subsegmental (in the segment 8), mesenteric marginal (Griffith point) and inferior phrenic arteries by using 5-point visual scoring systems. Kappa analysis was used for evaluation of interobserver agreement. To compare the visualization capability of the two systems, the Mann-Whitney U-test was used to compare the scores for each of the arteries. Results: Overall interobserver agreements for both systems were almost perfect (κ > 0.80). Visualization scores for inferior epigastric and mesenteric arteries were significantly higher for ADCT than for 64-detector row CT (p < 0.05). No significant difference was found for hepatic subsegmental and inferior phrenic arteries. Conclusion: Small abdominal vasculature assessment by ADCT with step-and-shoot scan protocol is potentially equal to or better than that by 64-detector row CT with helical scan protocol.

User Instructions for the Systems Assessment Capability, Rev. 0, Computer Codes Volume 2: Impact Modules

International Nuclear Information System (INIS)

Eslinger, Paul W.; Arimescu, Carmen; Kanyid, Beverly A.; Miley, Terri B.

2001-01-01

One activity of the Department of Energy?s Groundwater/Vadose Zone Integration Project is an assessment of cumulative impacts from Hanford Site wastes on the subsurface environment and the Columbia River. Through the application of a system assessment capability (SAC), decisions for each cleanup and disposal action will be able to take into account the composite effect of other cleanup and disposal actions. The SAC has developed a suite of computer programs to simulate the migration of contaminants (analytes) present on the Hanford Site and to assess the potential impacts of the analytes, including dose to humans, socio-cultural impacts, economic impacts, and ecological impacts. The general approach to handling uncertainty in the SAC computer codes is a Monte Carlo approach. Conceptually, one generates a value for every stochastic parameter in the code (the entire sequence of modules from inventory through transport and impacts) and then executes the simulation, obtaining an output value, or result. This document provides user instructions for the SAC codes that generate human, ecological, economic, and cultural impacts

Capabilities and Gaps Assessments of Urban Air Quality Manage-ment in Uganda

Directory of Open Access Journals (Sweden)

Amin Tamale Kiggundu

2015-06-01

Full Text Available Today, large cities across the globe are facing a pervasive problem of air pollution.  The purpose of this study is to assess the capabilities and gaps in urban air quality management in Uganda as well as proposing strategies for curbing air pollution. This study applied face to face interviews, targeting key informants such as the environmental experts, urbanization researchers and officials from the National Environment Management Authority (NEMA. Results show that rapid motorization, continued dependence on fossil fuels, open waste burning, biomass burning, industrialization, bushfires and urbanization are the key causes of air pollution in Uganda. To reduce air pollution and improve urban air quality it is critical to promote non-motorised mass transport, increase electricity access, regulate open waste burning, establish laboratories, strengthen local research and training capacity, promote collaborations, introduce more fuel efficient vehicles and periodic vehicle inspection and carry out public awareness campaigns about air pollution.

Technical and economic assessment of fluidized-bed-augmented compressed-air energy-storage system: system load following capability

Energy Technology Data Exchange (ETDEWEB)

Lessard, R.D.; Blecher, W.A.; Merrick, D.

1981-09-01

The load-following capability of fluidized bed combustion-augmented compressed air energy storage systems was evaluated. The results are presented in two parts. The first part is an Executive Summary which provides a concise overview of all major elements of the study including the conclusions, and, second, a detailed technical report describing the part-load and load following capability of both the pressurized fluid bed combustor and the entire pressurized fluid bed combustor/compressed air energy storage system. The specific tasks in this investigation were to: define the steady-state, part-load operation of the CAES open-bed PFBC; estimate the steady-state, part-load performance of the PFBC/CAES system and evaluate any possible operational constraints; simulate the performance of the PFBC/CAES system during transient operation and assess the load following capability of the system; and establish a start-up procedure for the open-bed PFBC and evaluate the impact of this procedure. The conclusions are encouraging and indicate that the open-bed PFBC/CAES power plant should provide good part-load and transient performance, and should have no major equipment-related constraints, specifically, no major problems associated with the performance or design of either the open-end PFBC or the PFBC/CAES power plant in steady-state, part-load operation are envisioned. The open-bed PFBC/CAES power plant would have a load following capability which would be responsive to electric utility requirements for a peak-load power plant. The open-bed PFBC could be brought to full operating conditions within 15 min after routine shutdown, by employing a hot-start mode of operation. The PFBC/CAES system would be capable of rapid changes in output power (12% of design load per minute) over a wide output power range (25% to 100% of design output). (LCL)

Instruments assessing attitudes toward or capability regarding self-management of osteoarthritis: a systematic review of measurement properties.

Science.gov (United States)

Eyles, J P; Hunter, D J; Meneses, S R F; Collins, N J; Dobson, F; Lucas, B R; Mills, K

2017-08-01

To make a recommendation on the "best" instrument to assess attitudes toward and/or capabilities regarding self-management of osteoarthritis (OA) based on available measurement property evidence. Electronic searches were performed in MEDLINE, EMBASE, CINAHL and PsychINFO (inception to 27 December 2016). Two reviewers independently rated measurement properties using the Consensus-based Standards for the selection of Health Measurement Instruments (COSMIN) 4-point scale. Best evidence synthesis was determined by considering COSMIN ratings for measurement property results and the level of evidence available for each measurement property of each instrument. Eight studies out of 5653 publications met the inclusion criteria, with eight instruments identified for evaluation: Multidimensional Health Locus of Control (MHLC), Perceived Behavioural Control (PBC), Patient Activation Measure (PAM), Educational Needs Assessment (ENAT), Stages of Change Questionnaire in Osteoarthritis (SCQOA), Effective Consumer Scale (EC-17) and Perceived Efficacy in Patient-Physician Interactions five item (PEPPI-5) and ten item scales. Measurement properties assessed for these instruments included internal consistency (k = 8), structural validity (k = 8), test-retest reliability (k = 2), measurement error (k = 1), hypothesis testing (k = 3) and cross-cultural validity (k = 3). No information was available for content validity, responsiveness or minimal important change (MIC)/minimal important difference (MID). The Dutch PEPPI-5 demonstrated the best measurement property evidence; strong evidence for internal consistency and structural validity but limited evidence for reliability and construct validity. Although PEPPI-5 was identified as having the best measurement properties, overall there is a poor level of evidence currently available concerning measurement properties of instruments to assess attitudes toward and/or capabilities regarding osteoarthritis self-management. Further

Assessment of Space Nuclear Thermal Propulsion Facility and Capability Needs

Energy Technology Data Exchange (ETDEWEB)

James Werner

2014-07-01

The development of a Nuclear Thermal Propulsion (NTP) system rests heavily upon being able to fabricate and demonstrate the performance of a high temperature nuclear fuel as well as demonstrating an integrated system prior to launch. A number of studies have been performed in the past which identified the facilities needed and the capabilities available to meet the needs and requirements identified at that time. Since that time, many facilities and capabilities within the Department of Energy have been removed or decommissioned. This paper provides a brief overview of the anticipated facility needs and identifies some promising concepts to be considered which could support the development of a nuclear thermal propulsion system. Detailed trade studies will need to be performed to support the decision making process.

Structural Capability of an Organization toward Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

The scholars in the field of strategic management have developed two major approaches for attainment of competitive advantage: an approach based on environmental opportunities, and another one based on internal capabilities of an organization. Some investigations in the last two decades have...... indicated that the advantages relying on the internal capabilities of organizations may determine the competitive position of organizations better than environmental opportunities do. Characteristics of firms shows that one of the most internal capabilities that lead the organizations to the strongest...... competitive advantage in the organizations is the innovation capability. The innovation capability is associated with other organizational capabilities, and many organizations have focused on the need to identify innovation capabilities.This research focuses on recognition of the structural aspect...

Design to Process Capabilities: challenges for the use of Process Capability Databases (PCDBs) in development

DEFF Research Database (Denmark)

Eifler, Tobias; Göhler, Simon Moritz; Howard, Thomas J.

2014-01-01

capabilities may lead to low yields and a cost/time overrun, conservatively underestimated capabilities affect quality through the reduced design space, or through increased play, rattle/noise, size or weight. A possibility to overcome the subjective assessment of variation in development projects is a Process...... and Maiti (2012), Breyfogle (2003)]. At the same time, information on the achievable manufacturing accuracy or the supplier’s performance is usually inaccurate and largely qualitative in early development stages. Design decisions as well as the choice of manufacturing processes, therefore, often rely...... Capability Data Base (PCDB) offering valuable insight into the actual or expected performance of production processes (Tata and Thornton, 1999). But although the potential benefits as well as initial challenges for the use of PCDBs have been addressed in earlier research, e. g. by Delaney and Phelan (2008...

Assessment of capabilities of lidar systems in day-and night-time under different atmospheric and internal-noise conditions

Science.gov (United States)

Agishev, Ravil; Comerón, Adolfo

2018-04-01

As an application of the dimensionless parameterization concept proposed earlier for the characterization of lidar systems, the universal assessment of lidar capabilities in day and night conditions is considered. The dimensionless parameters encapsulate the atmospheric conditions, the lidar optical and optoelectronic characteristics, including the photodetector internal noise, and the sky background radiation. Approaches to ensure immunity of the lidar system to external background radiation are discussed.

Model-based Assessment for Balancing Privacy Requirements and Operational Capabilities

Energy Technology Data Exchange (ETDEWEB)

Knirsch, Fabian [Salzburg Univ. (Austria); Engel, Dominik [Salzburg Univ. (Austria); Frincu, Marc [Univ. of Southern California, Los Angeles, CA (United States); Prasanna, Viktor [Univ. of Southern California, Los Angeles, CA (United States)

2015-02-17

The smart grid changes the way energy is produced and distributed. In addition both, energy and information is exchanged bidirectionally among participating parties. Therefore heterogeneous systems have to cooperate effectively in order to achieve a common high-level use case, such as smart metering for billing or demand response for load curtailment. Furthermore, a substantial amount of personal data is often needed for achieving that goal. Capturing and processing personal data in the smart grid increases customer concerns about privacy and in addition, certain statutory and operational requirements regarding privacy aware data processing and storage have to be met. An increase of privacy constraints, however, often limits the operational capabilities of the system. In this paper, we present an approach that automates the process of finding an optimal balance between privacy requirements and operational requirements in a smart grid use case and application scenario. This is achieved by formally describing use cases in an abstract model and by finding an algorithm that determines the optimum balance by forward mapping privacy and operational impacts. For this optimal balancing algorithm both, a numeric approximation and – if feasible – an analytic assessment are presented and investigated. The system is evaluated by applying the tool to a real-world use case from the University of Southern California (USC) microgrid.

Exploration Medical Capability - Technology Watch

Science.gov (United States)

Krihak, Michael; Watkins, Sharmila; Barr, Yael; Barsten, Kristina; Fung, Paul; Baumann, David

2011-01-01

The objectives of the Technology Watch process are to identify emerging, high-impact technologies that augment current ExMC development efforts, and to work with academia, industry, and other government agencies to accelerate the development of medical care and research capabilities for the mitigation of potential health issues that could occur during space exploration missions. The establishment of collaborations with these entities is beneficial to technology development, assessment and/or insertion. Such collaborations also further NASA s goal to provide a safe and healthy environment for human exploration. The Tech Watch project addresses requirements and capabilities identified by knowledge and technology gaps that are derived from a discrete set of medical conditions that are most likely to occur on exploration missions. These gaps are addressed through technology readiness level assessments, market surveys, collaborations and distributed innovation opportunities. Ultimately, these gaps need to be closed with respect to exploration missions, and may be achieved through technology development projects. Information management is a key aspect to this process where Tech Watch related meetings, research articles, collaborations and partnerships are tracked by the HRP s Exploration Medical Capabilities (ExMC) Element. In 2011, ExMC will be introducing the Tech Watch external website and evidence wiki that will provide access to ExMC technology and knowledge gaps, technology needs and requirements documents.

Initial demonstration of the NRC`s capability to conduct a performance assessment for a High-Level Waste Repository

Energy Technology Data Exchange (ETDEWEB)

Codell, R.; Eisenberg, N.; Fehringer, D.; Ford, W.; Margulies, T.; McCartin, T.; Park, J.; Randall, J.

1992-05-01

In order to better review licensing submittals for a High-Level Waste Repository, the US Nuclear Regulatory Commission staff has expanded and improved its capability to conduct performance assessments. This report documents an initial demonstration of this capability. The demonstration made use of the limited data from Yucca Mountain, Nevada to investigate a small set of scenario classes. Models of release and transport of radionuclides from a repository via the groundwater and direct release pathways provided preliminary estimates of releases to the accessible environment for a 10,000 year simulation time. Latin hypercube sampling of input parameters was used to express results as distributions and to investigate model sensitivities. This methodology demonstration should not be interpreted as an estimate of performance of the proposed repository at Yucca Mountain, Nevada. By expanding and developing the NRC staff capability to conduct such analyses, NRC would be better able to conduct an independent technical review of the US Department of Energy (DOE) licensing submittals for a high-level waste (HLW) repository. These activities were divided initially into Phase 1 and Phase 2 activities. Additional phases may follow as part of a program of iterative performance assessment at the NRC. The NRC staff conducted Phase 1 activities primarily in CY 1989 with minimal participation from NRC contractors. The Phase 2 activities were to involve NRC contractors actively and to provide for the transfer of technology. The Phase 2 activities are scheduled to start in CY 1990, to allow Sandia National Laboratories to complete development and transfer of computer codes and the Center for Nuclear Waste Regulatory Analyses (CNWRA) to be in a position to assist in the acquisition of the codes.

Analysis of Biological Interactions by Affinity Chromatography: Clinical and Pharmaceutical Applications.

Science.gov (United States)

Hage, David S

2017-06-01

The interactions between biochemical and chemical agents in the body are important in many clinical processes. Affinity chromatography and high-performance affinity chromatography (HPAC), in which a column contains an immobilized biologically related binding agent, are 2 methods that can be used to study these interactions. This review presents various approaches that can be used in affinity chromatography and HPAC to characterize the strength or rate of a biological interaction, the number and types of sites that are involved in this process, and the interactions between multiple solutes for the same binding agent. A number of applications for these methods are examined, with an emphasis on recent developments and high-performance affinity methods. These applications include the use of these techniques for fundamental studies of biological interactions, high-throughput screening of drugs, work with modified proteins, tools for personalized medicine, and studies of drug-drug competition for a common binding agent. The wide range of formats and detection methods that can be used with affinity chromatography and HPAC for examining biological interactions makes these tools attractive for various clinical and pharmaceutical applications. Future directions in the development of small-scale columns and the coupling of these methods with other techniques, such as mass spectrometry or other separation methods, should continue to increase the flexibility and ease with which these approaches can be used in work involving clinical or pharmaceutical samples. © 2016 American Association for Clinical Chemistry.

Isoprene Production on Enzymatic Hydrolysate of Peanut Hull Using Different Pretreatment Methods

Directory of Open Access Journals (Sweden)

Sumeng Wang

2016-01-01

Full Text Available The present study is about the use of peanut hull for isoprene production. In this study, two pretreatment methods, hydrogen peroxide-acetic acid (HPAC and popping, were employed prior to enzymatic hydrolysis, which could destroy the lignocellulosic structure and accordingly improve the efficiency of enzymatic hydrolysis. It is proven that the isoprene production on enzymatic hydrolysate with HPAC pretreatment is about 1.9-fold higher than that of popping pretreatment. Moreover, through High Performance Liquid Chromatography (HPLC analysis, the amount and category of inhibitors such as formic acid, acetic acid, and HMF were assayed and were varied in different enzymatic hydrolysates, which may be the reason leading to a decrease in isoprene production during fermentation. To further increase the isoprene yield, the enzymatic hydrolysate of HPAC was detoxified by activated carbon. As a result, using the detoxified enzymatic hydrolysate as the carbon source, the engineered strain YJM21 could accumulate 297.5 mg/L isoprene, which accounted for about 90% of isoprene production by YJM21 fermented on pure glucose (338.6 mg/L. This work is thought to be the first attempt on isoprene production by E. coli using peanut hull as the feedstock. More importantly, it also shows the prospect of peanut hull to be considered as an alternative feedstock for bio-based chemicals or biofuels production due to its easy access and high polysaccharide content.

Trends in Microfabrication Capabilities & Device Architectures.

Energy Technology Data Exchange (ETDEWEB)

Bauer, Todd [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Jones, Adam [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Lentine, Tony [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Mudrick, John [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Okandan, Murat [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rodrigues, Arun [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2015-06-01

The last two decades have seen an explosion in worldwide R&D, enabling fundamentally new capabilities while at the same time changing the international technology landscape. The advent of technologies for continued miniaturization and electronics feature size reduction, and for architectural innovations, will have many technical, economic, and national security implications. It is important to anticipate possible microelectronics development directions and their implications on US national interests. This report forecasts and assesses trends and directions for several potentially disruptive microfabrication capabilities and device architectures that may emerge in the next 5-10 years.

Materials capability review Los Alamos National Laboratory, May 3-6, 2010

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoinette [Los Alamos National Laboratory

2010-01-01

The 2010 'Capability Review' process at LANL significantly differs from the Division reviews of prior years. The Capabilities being reviewed (some 4-8 per year) are deliberately chosen to be crosscutting over the Laboratory, and therefore will include not only several experimental, theoretical and simulation disciplines, but also contributions from multiple line organizations. This approach is consistent with the new Laboratory organizational structure, focusing on agile and integrated capabilities applied to present national security missions, and also nurtured to be available for rapid application to future missions. The overall intent is that the Committee assess the quality of the science, engineering, and technology identified in the agenda, and advise the LANS Board of Governors and Laboratory management. Specifically, the Committees will: (1) Assess the quality of science, technology and engineering within the Capability in the areas defined in the agenda. Identify issues to develop or enhance the core competencies within this capability. (2) Evaluate the integration of this capability across the Laboratory organizations that are listed in the agenda in terms of joint programs, projects, proposals, and/or publications. Describe the integration of this capability in the wider scientific community using the recognition as a leader within the community, ability to set research agendas, and attraction and retention of staff. (3) Assess the quality and relevance of this capability's science, technology and engineering contributions to current and emerging Laboratory programs, including Nuclear Weapons, Threat Reduction/Homeland Security, and Energy Security. (4) Advise the Laboratory Director/Principal Associate Director for Science, Technology and Engineering on the health of the Capability including the current and future (5 year) science, technology and engineering staff needs, mix of research and development activities, program opportunities

Materials Capability Review Los Alamos National Laboratory April 29-May 2, 2012

Energy Technology Data Exchange (ETDEWEB)

Taylor, Antoinette J [Los Alamos National Laboratory

2012-04-20

Los Alamos National Laboratory (LANL) uses Capability Reviews to assess the quality and institutional integration of science, technology and engineering (STE) and to advise Laboratory Management on the current and future health of LANL STE. The capabilities are deliberately chosen to be crosscutting over the Laboratory and therefore will include experimental, theoretical and simulation disciplines from multiple line organizations. Capability Reviews are designed to provide a more holistic view of the STE quality, integration to achieve mission requirements, and mission relevance. The scope of these capabilities necessitate that there will be significant overlap in technical areas covered by capability reviews (e.g., materials research and weapons science and engineering). In addition, LANL staff may be reviewed in different capability reviews because of their varied assignments and expertise. The principal product of the Capability Review is the report that includes the review committee's assessments, recommendations, and recommendations for STE.

The Armored Brigade Combat Team (ABCT) in the Future: An Assessment of Capabilities Against the Hybrid Threat in the Future Operational Environment

Science.gov (United States)

2013-06-13

requirements, followed by a tactical case study assessment, and a strengths, weaknesses, opportunities, and threats ( SWOT ) analysis of the BCTs against a...strategic and operational deployment. This information further developed the case study SWOT analysis of the BCTs against a hybrid threat. The SWOT ...a SWOT analysis . The next section addressed is the analysis . The analysis is comprised of the strategic capabilities assessment and the tactical

The development and initial assessment of the strategy and leadership systems capability evaluation survey.

Science.gov (United States)

Coon, Cheryl D; Bokowy, Kay L; Horblyuk, Ruslan; Zisman, Robert S; McLeod, Lori D; Brown, T Michelle

2012-01-01

Hospital management and leadership systems are associated with organizational success and quality care. The Strategy and Leadership Systems Capability Evaluation (CE) survey was developed by GE Healthcare to assess management and leadership systems at health care institutions, serve as a benchmark for improvement, and measure progress. To assess the psychometric properties of the 29-item CE survey, including the factor structure, scoring algorithm, reliability, and discriminant validity, an online survey was completed by 3450 employees at 15 US hospitals. Of these employees, 609 worked at a hospital where a leadership and management intervention occurred after the initial survey administration. Data were also collected on job level, number of hospital beds, hospital ownership, location, community type, and the implementation of hospital interventions. Item response frequencies showed no floor or ceiling effects and limited missing data. Interitem correlations were strong without obvious redundancies, and factor analysis suggested a unidimensional scale. The resulting scale had strong internal consistency and was able to discriminate among known groups. The CE survey was developed to evaluate management and leadership systems at health care institutions. This study provides psychometric evidence in support of the reliability, validity, and scoring structure of this survey.

Tracing Assessment for learning Capability in Teachers (TACT)

DEFF Research Database (Denmark)

Otrel-Cass, Kathrin; Agerbo, Jette Nørgaard; Skipper-Jørgensen, Anette

2018-01-01

education program. This chapter presents preliminary survey and focus group interviews data after tracing 21 pre-service teachers over two years. Our findings reflected a picture of Danish student teachers who value in particular formative assessment practices, while summative assessment is acknowledged......The focus on assessment literate teachers who know how to construct, administer assessments and communicate learning outcomes on student learning raises questions on how student teachers can develop the necessary skills to assess their students' learning. This is so important since...... there is evidence that beginning teachers continue to feel under prepared to assess student learning. This chapter presents findings of a study conducted in Denmark with the aim of investigating how student teacher candidates develop the capacities to become ‘assessment literate' over the course of their teacher...

Developing an International Survey of Teachers' Assessment Capabilities

DEFF Research Database (Denmark)

Renken, Maggie; Otrel-Cass, Kathrin; Cowie, Bronwen

teacher education into the first years as teachers across six countries. We target the nature of programmes and changes in understanding assessment purposes, practices, principles and policy. This project builds on the ACT survey of student-teacher understandings of assessment conducted over three years......Professional standards require teachers to be assessment literate - to construct, administer, and score reliable, valid assessments, communicate interpretations and use evidence to adjust teaching to support students. This project investigates student-teachers’ assessment literacy throughout...

Integrated Risk-Capability Analysis under Deep Uncertainty : An ESDMA Approach

NARCIS (Netherlands)

Pruyt, E.; Kwakkel, J.H.

2012-01-01

Integrated risk-capability analysis methodologies for dealing with increasing degrees of complexity and deep uncertainty are urgently needed in an ever more complex and uncertain world. Although scenario approaches, risk assessment methods, and capability analysis methods are used, few organizations

Vulnerability, Health Agency and Capability to Health.

Science.gov (United States)

Straehle, Christine

2016-01-01

One of the defining features of the capability approach (CA) to health, as developed in Venkatapuram's book Health Justice, is its aim to enable individual health agency. Furthermore, the CA to health hopes to provide a strong guideline for assessing the health-enabling content of social and political conditions. In this article, I employ the recent literature on the liberal concept of vulnerability to assess the CA. I distinguish two kinds of vulnerability. Considering circumstantial vulnerability, I argue that liberal accounts of vulnerability concerned with individual autonomy, align with the CA to health. Individuals should, as far as possible, be able to make health-enabling decisions about their lives, and their capability to do so should certainly not be hindered by public policy. The CA to health and a vulnerability-based analysis then work alongside to define moral responsibilities and designate those who hold them. Both approaches demand social policy to address circumstances that hinder individuals from taking health-enabling decisions. A background condition of vulnerability, on the other hand, even though it hampers the capability for health, does not warrant the strong moral claim proposed by the CA to health to define health as a meta-capability that should guide social policy. Nothing in our designing social policy could change the challenge to health agency when we deal with background conditions of vulnerability. © 2016 John Wiley & Sons Ltd.

University-Industry Research Collaboration: A Model to Assess University Capability

Science.gov (United States)

Abramo, Giovanni; D'Angelo, Ciriaco Andrea; Di Costa, Flavia

2011-01-01

Scholars and policy makers recognize that collaboration between industry and the public research institutions is a necessity for innovation and national economic development. This work presents an econometric model which expresses the university capability for collaboration with industry as a function of size, location and research quality. The…

Preliminary assessment of the imaging capability of the YAP-(S)PET small animal scanner in neuroscience

International Nuclear Information System (INIS)

Bartoli, Antonietta; Belcari, Nicola; Stark, Daniela; Hoehnemann, Sabine; Piel, Markus; Jennewein, Marc; Schmitt, Ulrich; Tillmanns, Julia; Thews, Oliver; Hiemke, Christoph; Roesch, Frank; Del Guerra, Alberto

2006-01-01

The new and fully engineered version of the YAP-(S)PET small animal scanner has been tested at the University of Mainz for preliminary assessment of its imaging capability for studies related to neuropharmacology and psychiatry. The main feature of the scanner is the capability to combine PET and SPECT techniques. It allows the development of new and interesting protocols for the investigation of many biological phenomena, more effectively than with PET or SPECT modalities alone. The scanner is made up of four detector heads, each one composed of a 4x4 cm 2 of YAlO 3 :Ce (or YAP:Ce) matrix, and has a field of view (FOV) of 4 cm axiallyx4 cm o transaxially. In PET mode, the volume resolution is less than 8 mm 3 and is nearly constant over the whole FOV, while the sensitivity is about 2%. The SPECT performance is not so good, due to the presence of the multi-hole lead collimator in front of each head. Nevertheless, the YAP-PET scanner offers excellent resolution and sensitivity for performing on the availability of D2-like dopamine receptors on mice and rats in both PET and SPECT modalities

The Orphee reactor current status and proposed enhancement of experimental capabilities

International Nuclear Information System (INIS)

Breant, P.

1990-01-01

This report provides a description of the Orphee reactor, together with a rapid assessment of its experimental and research capabilities. The plans for enhancing the reactor's experimental capabilities are also presented. (author)

Impact of Personnel Capabilities on Organizational Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

in this rapidly changing world. This research focuses on definition of the personnel aspect of innovation capability, and proposes a conceptual model based on the scientific articles of academic literature on organisations innovation capability. This paper includes an expert based validation in three rounds...... of the Delphi method. And for the purpose of a better appreciation of the relationship dominating the factors of the model, it has distributed the questionnaire to Iranian companies in the Food industry. This research proposed a direct relationship between Innovation Capability and the Personnel Capability...

Validation of foF2 and TEC Modeling During Geomagnetic Disturbed Times: Preliminary Outcomes of International Forum for Space Weather Modeling Capabilities Assessment

Science.gov (United States)

Shim, J. S.; Tsagouri, I.; Goncharenko, L. P.; Kuznetsova, M. M.

2017-12-01

To address challenges of assessment of space weather modeling capabilities, the CCMC (Community Coordinated Modeling Center) is leading the newly established "International Forum for Space Weather Modeling Capabilities Assessment." This presentation will focus on preliminary outcomes of the International Forum on validation of modeled foF2 and TEC during geomagnetic storms. We investigate the ionospheric response to 2013 Mar. geomagnetic storm event using ionosonde and GPS TEC observations in North American and European sectors. To quantify storm impacts on foF2 and TEC, we first quantify quiet-time variations of foF2 and TEC (e.g., the median and the average of the five quietest days for the 30 days during quiet conditions). It appears that the quiet time variation of foF2 and TEC are about 10% and 20-30%, respectively. Therefore, to quantify storm impact, we focus on foF2 and TEC changes during the storm main phase larger than 20% and 50%, respectively, compared to 30-day median. We find that in European sector, both foF2 and TEC response to the storm are mainly positive phase with foF2 increase of up to 100% and TEC increase of 150%. In North America sector, however, foF2 shows negative effects (up to about 50% decrease), while TEC shows positive response (the largest increase is about 200%). To assess modeling capability of reproducing the changes of foF2 and TEC due to the storm, we use various model simulations, which are obtained from empirical, physics-based, and data assimilation models. The performance of each model depends on the selected metrics, therefore, only one metrics is not enough to evaluate the models' predictive capabilities in capturing the storm impact. The performance of the model also varies with latitude and longitude.

The short-term effects of effort-reward imbalance : Daily and within-day psychological and physiological measurements

NARCIS (Netherlands)

Hanson, E.K.S.

2000-01-01

In the present thesis, the short-term effects of Effort-Reward Imbalance (ERI) are studied by measuring indices of vagal control, hypothalamo-pituitary-adrenocortical (HPAC) activity and affect. The studies provide an illustration of recent developments in the field. Primarily, Ecological Momentary

Improved thermal source term generation capability for use in performance assessment and system studies

International Nuclear Information System (INIS)

King, J.; Rhodes, C.

1994-01-01

This paper describes work performed by the Civilian Radioactive Waste Management System (CRWMS) Management and Operating (M ampersand O) Contractor to improve spent nuclear fuel (SNF) waste stream characterization for system studies. It discusses how these new capabilities may be exploited for thermal source term generation for use in repository performance assessment modeling. SNF historical discharges have been exhaustively tracked, and significant effort has gone into capturing, verifying, and electronically managing spent fuel inventory data. Future discharge projections are produced annually by the Energy Information Administration (EIA) using sophisticated computer models. The output of these models is coupled with annually updated SNF historical discharges to produce what is referred to as the open-quotes reactor database.close quotes This database and related data are published in a variety of ways including on magnetic media for consistent use by analysts or other interested parties

Capability Paternalism

NARCIS (Netherlands)

Claassen, R.J.G.|info:eu-repo/dai/nl/269266224

A capability approach prescribes paternalist government actions to the extent that it requires the promotion of specific functionings, instead of the corresponding capabilities. Capability theorists have argued that their theories do not have much of these paternalist implications, since promoting

Risk assessment of the upstream petroleum industry's oil spill response equipment capability in western Canada

International Nuclear Information System (INIS)

Wotherspoon, P.; Brown, L.; Sawyer, M.

1993-01-01

A key component in the development of an effective onshore oil spill response capability is the type, condition, and geographical placement of oil spill equipment. When spill response equipment is first being purchased for a particular operating area, a brief analysis should be conducted to ensure that the equipment would provide an adequate response capability for that area. This response capability may change over time with variations in oil field production capabilities, pipelines and markets, company ownerships, manpower availability, and other logistical changes. Equipment may also become inoperable or redundant. These problems may be effectively addressed if one operator or spill cooperative actively reviews their spill response capabilities on a regular (annual) basis. However, when multiple operators and cooperatives exist over an extensive geographical area, the responsibility for regularly review of the capabilities of spill equipment may become lost in the organizational structure and in other responsibilities. In addition, the responsibility to conduct a multiarea review of the surrounding area may never be identified

A Risk Assessment Methodology for Divesting Military Capabilities to Allied Nations

National Research Council Canada - National Science Library

Gastelum, Jason A

2006-01-01

.... can sustain such a level of defense investment. One strategy to offset the increasing burden of defense spending is to divest the procurement and/or sustainment of individual defense capabilities to allied nations...

Assessment of Satellite Capabilities to Detect Impacts of Oil and Natural Gas Activity by Analysis of SONGNEX 2015 Aircraft Measurements

Science.gov (United States)

Thayer, M. P.; Keutsch, F. N.; Wolfe, G.; St Clair, J. M.; Hanisco, T. F.; Aikin, K. C.; Brown, S. S.; Dubé, W.; Eilerman, S. J.; Gilman, J.; De Gouw, J. A.; Koss, A.; Lerner, B. M.; Neuman, J. A.; Peischl, J.; Ryerson, T. B.; Thompson, C. R.; Veres, P. R.; Warneke, C.; Washenfelder, R. A.; Wild, R. J.; Womack, C.; Yuan, B.; Zarzana, K. J.

2017-12-01

In the last decade, the rate of domestic energy production from oil and natural gas has grown dramatically, resulting in increased concurrent emissions of methane and other volatile organic compounds (VOCs). Products of VOC oxidation and radical cycling, such as tropospheric ozone (O3) and secondary organic aerosols (SOA), have detrimental impacts on human health and climate. The ability to monitor these emissions and their impact on atmospheric composition from remote-sensing platforms will benefit public health by improving air quality forecasts and identifying localized drivers of tropospheric pollution. New satellite-based instruments, such as TROPOMI (October 2017 launch) and TEMPO (2019-2021 projected launch), will be capable of measuring chemical species related to energy drilling and production on unprecedented spatial and temporal scales, however there is need for improved assessments of their capabilities with respect to specific applications. We use chemical and physical parameters measured via aircraft in the boundary layer and free troposphere during the Shale Oil and Natural Gas Nexus (SONGNEX 2015) field campaign to view chemical enhancements over tight oil and shale gas basins from a satellite perspective. Our in-situ data are used to calculate the planetary boundary layer contributions to the column densities for formaldehyde, glyoxal, O3, and NO2. We assess the spatial resolution and chemical precisions necessary to resolve various chemical features, and compare these limits to TEMPO and TROPOMI capabilities to show the degree to which their retrievals will be able to discern the signatures of oil and natural gas activity.

UK regulatory expectations for the development of licensee organisational capability

International Nuclear Information System (INIS)

Gibson, S.; Reiersen, Craig

2011-01-01

The Nuclear Installations Inspectorate (NII) is responsible for the licensing and regulatory oversight of new nuclear power reactors in the UK. NII recognises that effective licensee leadership and management for safety are instrumental in the safety of new and existing nuclear installations. NII is consequently placing considerable emphasis on seeking assurance that prospective licensees develop an adequate organisational capability to manage and deliver nuclear safety in addition to constructing a design that has passed through a rigorous assessment process. In order to make NII's expectations clear, and support a consistent approach to interactions with prospective licensees, NII has produced a suite of related guidance to help its Inspectors assess and influence the development of licensee organisational capability. This includes: 1. The safety management prospectus; 2. The 'nuclear baseline'; 3. Intelligent Customer capability and use of contractors; 4. Design Authority; 5. Licence Condition Compliance Arrangements; 6. Development of Organisational Capability

Prioritization Assessment for Capability Gaps in Weapon System of Systems Based on the Conditional Evidential Network

Directory of Open Access Journals (Sweden)

Dong Pei

2018-02-01

Full Text Available The prioritization of capability gaps for weapon system of systems is the basis for design and capability planning in the system of systems development process. In order to address input information uncertainties, the prioritization of capability gaps is computed in two steps using the conditional evidential network method. First, we evaluated the belief distribution of degree of required satisfaction for capabilities, and then calculated the reverse conditional belief function between capability hierarchies. We also provided verification for the feasibility and effectiveness of the proposed method through a prioritization of capability gaps calculation using an example of a spatial-navigation-and-positioning system of systems.

A Measurement Framework for Team Level Assessment of Innovation Capability in Early Requirements Engineering

Science.gov (United States)

Regnell, Björn; Höst, Martin; Nilsson, Fredrik; Bengtsson, Henrik

When developing software-intensive products for a market-place it is important for a development organisation to create innovative features for coming releases in order to achieve advantage over competitors. This paper focuses on assessment of innovation capability at team level in relation to the requirements engineering that is taking place before the actual product development projects are decided, when new business models, technology opportunities and intellectual property rights are created and investigated through e.g. prototyping and concept development. The result is a measurement framework focusing on four areas: innovation elicitation, selection, impact and ways-of-working. For each area, candidate measurements were derived from interviews to be used as inspiration in the development of a tailored measurement program. The framework is based on interviews with participants of a software team with specific innovation responsibilities and validated through cross-case analysis and feedback from practitioners.

Preliminary assessment of the benefits of derating a cask for increasing age/burnup capability

International Nuclear Information System (INIS)

Broadhead, B.L.; Parks, C.V.; Joy, D.S.; Tang, J.S.

1992-01-01

This paper discusses a study performed to determine the extent to which the age/burnup capability of the Babcock and Wilcox BR-100 rail cask could be extended by reducing the number of fuel assemblies. Only the shielding effects of derating are accounted for in this study. Separate analyses will be necessary to address the enhanced heat loads due to increased burnup or decreased age. The criterion used to assess the derating was the calculated dose 2 m from the rail car. The reference calculations were based on the 70% design of the BR-100 cask with 21 PWR fuel assemblies. Seven different basket/assembly loading configurations were investigated. The results indicate that both an alternative 18-assembly basket configuration and a 17-assembly/4-empty-hole configuration for the 21-element basket offer substantial gains over the fully loaded reference 21-element basket configuration

Preliminary assessment of the imaging capability of the YAP-(S)PET small animal scanner in neuroscience

Energy Technology Data Exchange (ETDEWEB)

Bartoli, Antonietta [Department of Physics ' E. Fermi' and Center of Excellence ' AmbiSEN' , University of Pisa, and INFN, Sezione di Pisa, Pisa I- 56127 (Italy)]. E-mail: bartoli@df.unipi.it; Belcari, Nicola [Department of Physics ' E. Fermi' and Center of Excellence ' AmbiSEN' , University of Pisa, and INFN, Sezione di Pisa, Pisa I- 56127 (Italy); Stark, Daniela [Institute of Nuclear Chemistry, University of Mainz, Mainz D-55099 (Germany); Hoehnemann, Sabine [Institute of Nuclear Chemistry, University of Mainz, Mainz D-55099 (Germany); Piel, Markus [Institute of Nuclear Chemistry, University of Mainz, Mainz D-55099 (Germany); Jennewein, Marc [Institute of Nuclear Chemistry, University of Mainz, Mainz D-55099 (Germany); Schmitt, Ulrich [Department of Psychiatry, University of Mainz, Mainz D-55099 (Germany); Tillmanns, Julia [Institute of Physiology and Pathophysiology, University of Mainz, Mainz D-55099 (Germany); Thews, Oliver [Institute of Physiology and Pathophysiology, University of Mainz, Mainz D-55099 (Germany); Hiemke, Christoph [Department of Psychiatry, University of Mainz, Mainz D-55099 (Germany); Roesch, Frank [Institute of Nuclear Chemistry, University of Mainz, Mainz D-55099 (Germany); Del Guerra, Alberto [Department of Physics ' E. Fermi' and Center of Excellence ' AmbiSEN' , University of Pisa, and INFN, Sezione di Pisa, Pisa I- 56127 (Italy)

2006-12-20

The new and fully engineered version of the YAP-(S)PET small animal scanner has been tested at the University of Mainz for preliminary assessment of its imaging capability for studies related to neuropharmacology and psychiatry. The main feature of the scanner is the capability to combine PET and SPECT techniques. It allows the development of new and interesting protocols for the investigation of many biological phenomena, more effectively than with PET or SPECT modalities alone. The scanner is made up of four detector heads, each one composed of a 4x4 cm{sup 2} of YAlO{sub 3}:Ce (or YAP:Ce) matrix, and has a field of view (FOV) of 4 cm axiallyx4 cm o transaxially. In PET mode, the volume resolution is less than 8 mm{sup 3} and is nearly constant over the whole FOV, while the sensitivity is about 2%. The SPECT performance is not so good, due to the presence of the multi-hole lead collimator in front of each head. Nevertheless, the YAP-PET scanner offers excellent resolution and sensitivity for performing on the availability of D2-like dopamine receptors on mice and rats in both PET and SPECT modalities.

Stakeholder Alignment and Changing Geospatial Information Capabilities

Science.gov (United States)

Winter, S.; Cutcher-Gershenfeld, J.; King, J. L.

2015-12-01

Changing geospatial information capabilities can have major economic and social effects on activities such as drought monitoring, weather forecasts, agricultural productivity projections, water and air quality assessments, the effects of forestry practices and so on. Whose interests are served by such changes? Two common mistakes are assuming stability in the community of stakeholders and consistency in stakeholder behavior. Stakeholder communities can reconfigure dramatically as some leave the discussion, others enter, and circumstances shift — all resulting in dynamic points of alignment and misalignment . New stakeholders can bring new interests, and existing stakeholders can change their positions. Stakeholders and their interests need to be be considered as geospatial information capabilities change, but this is easier said than done. New ways of thinking about stakeholder alignment in light of changes in capability are presented.

Improving global laboratory capabilities for emergency radionuclide bioassay

International Nuclear Information System (INIS)

Li, C.; Jourdain, J.; Kramer, G. H.

2012-01-01

During a radiological or nuclear emergency, first-responders and the general public may be internally contaminated with the radionuclide(s) involved. A timely radionuclide bioassay provides important information about contamination, for subsequent dose assessment and medical management. Both technical and operational gaps are discussed in this paper. As many people may need to be assessed in a short period of time, any single laboratory may find its capabilities insufficient. Laboratories from other regions or other countries may be called upon for assistance. This paper proposes a road-map to improve global capabilities in emergency radionuclide bioassay, suggesting a phased approach for establishing a global laboratory network. Existing international collaboration platforms could provide the base on which to build such a network. (authors)

Dynamic capabilities, Marketing Capability and Organizational Performance

Directory of Open Access Journals (Sweden)

Adriana Roseli Wünsch Takahashi

2017-01-01

Full Text Available The goal of the study is to investigate the influence of dynamic capabilities on organizational performance and the role of marketing capabilities as a mediator in this relationship in the context of private HEIs in Brazil. As a research method we carried out a survey with 316 IES and data analysis was operationalized with the technique of structural equation modeling. The results indicate that the dynamic capabilities have influence on organizational performance only when mediated by marketing ability. The marketing capability has an important role in the survival, growth and renewal on educational services offerings for HEIs in private sector, and consequently in organizational performance. It is also demonstrated that mediated relationship is more intense for HEI with up to 3,000 students and other organizational profile variables such as amount of courses, the constitution, the type of institution and type of education do not significantly alter the results.

Effects of Organisational Characteristics on Contractors’ Construction Cash Flow Forecasting Capabilities

Directory of Open Access Journals (Sweden)

Muhammad Abdullahi

2017-01-01

Full Text Available Inadequate cash resources resulting from poor cash flows have been among the fundamental causes of construction project failures. Despite the panoply of cash flow forecasting (CFF tools, the cash flow performance of many construction firms have been reported to be poor due weak Cash flow forecasting (CFF process capabilities influenced by a couple of organisational characteristics. Although these organisational characteristics have been reported to significantly influence firms’ CFF process capabilities, the underlying mechanisms of how these organisational features and characteristics exhibit their specific influences on the cash flow forecasting capabilities of construction firms still remains underexplored. Therefore, this study aims at empirically exploring the influence of some organisation characteristics on the CFF process capabilities of construction firms. Best practices in CFF identified from the Royal Institute of Chartered Surveyors (RICS Cash Flow Forecasting (CFF guide were used to develop an assessment criteria used to assess the CFF capabilities of construction firms. The assessment was conducted through a questionnaire survey involving contracting organisations involved in both building and civil engineering works in Nigeria. The key best practices in CFF were ranked based on arithmetic mean value scores and averages were also determined for each of the four CFF components assessed (Knowledge and understanding CFF concepts and principles, Practical application, Practical considerations, and other Managerial issues. Hierarchical regression analysis was then used to examine the relationships between contractors’’ CFF process capabilities and some organisational characteristics. Results of the study reveals that organisational characteristics are strongly associated to firms’ abilities to prudently manage cash flows. The results of this study could serve as a basis for the strategic planning and improvement of Cash Flow

Group Capability Model

Science.gov (United States)

Olejarski, Michael; Appleton, Amy; Deltorchio, Stephen

2009-01-01

The Group Capability Model (GCM) is a software tool that allows an organization, from first line management to senior executive, to monitor and track the health (capability) of various groups in performing their contractual obligations. GCM calculates a Group Capability Index (GCI) by comparing actual head counts, certifications, and/or skills within a group. The model can also be used to simulate the effects of employee usage, training, and attrition on the GCI. A universal tool and common method was required due to the high risk of losing skills necessary to complete the Space Shuttle Program and meet the needs of the Constellation Program. During this transition from one space vehicle to another, the uncertainty among the critical skilled workforce is high and attrition has the potential to be unmanageable. GCM allows managers to establish requirements for their group in the form of head counts, certification requirements, or skills requirements. GCM then calculates a Group Capability Index (GCI), where a score of 1 indicates that the group is at the appropriate level; anything less than 1 indicates a potential for improvement. This shows the health of a group, both currently and over time. GCM accepts as input head count, certification needs, critical needs, competency needs, and competency critical needs. In addition, team members are categorized by years of experience, percentage of contribution, ex-members and their skills, availability, function, and in-work requirements. Outputs are several reports, including actual vs. required head count, actual vs. required certificates, CGI change over time (by month), and more. The program stores historical data for summary and historical reporting, which is done via an Excel spreadsheet that is color-coded to show health statistics at a glance. GCM has provided the Shuttle Ground Processing team with a quantifiable, repeatable approach to assessing and managing the skills in their organization. They now have a common

COMPETITIVE INTELLIGENCE: THE ENHANCING ROLE OF ORGANIZATIONAL LEARNING CAPABILITY

OpenAIRE

HAMAD, Zaina Mustafa Mahmoud; YOZGAT, Ugur

2017-01-01

Performinga strong intelligence grants an organization a guaranteeof long-term success. This paper investigates the enhancing effect of organizational learning capabilities on competitive intelligence atthe commercial banks in Jordan. A sample within top and middle managements was used.Measurement instrument validity and model fit were assessed before testinghypotheses. This study emphasizes the role learning capability plays inenhancing intelligence. Key findings support importance of organi...

Sandia Laboratories technical capabilities. Auxiliary capabilities: environmental health information science

International Nuclear Information System (INIS)

1975-09-01

Sandia Laboratories is an engineering laboratory in which research, development, testing, and evaluation capabilities are integrated by program management for the generation of advanced designs. In fulfilling its primary responsibility to ERDA, Sandia Laboratories has acquired extensive research and development capabilities. The purpose of this series of documents is to catalog the many technical capabilities of the Laboratories. After the listing of capabilities, supporting information is provided in the form of highlights, which show applications. This document deals with auxiliary capabilities, in particular, environmental health and information science. (11 figures, 1 table) (RWR)

Advanced Simulation Capability for Environmental Management: Development and Demonstrations - 12532

Energy Technology Data Exchange (ETDEWEB)

Freshley, Mark D.; Freedman, Vicky; Gorton, Ian [Pacific Northwest National Laboratory, MSIN K9-33, P.O. Box 999, Richland, WA 99352 (United States); Hubbard, Susan S. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 50B-4230, Berkeley, CA 94720 (United States); Moulton, J. David; Dixon, Paul [Los Alamos National Laboratory, MS B284, P.O. Box 1663, Los Alamos, NM 87544 (United States)

2012-07-01

The U.S. Department of Energy Office of Environmental Management (EM), Technology Innovation and Development is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of capabilities, which are organized into Platform and Integrated Tool-sets and a High-Performance Computing Multi-process Simulator. The Platform capabilities target a level of functionality to allow end-to-end model development, starting with definition of the conceptual model and management of data for model input. The High-Performance Computing capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The new capabilities are demonstrated through working groups, including one focused on the Hanford Site Deep Vadose Zone. The ASCEM program focused on planning during the first year and executing a prototype tool-set for an early demonstration of individual components. Subsequently, ASCEM has focused on developing and demonstrating an integrated set of capabilities, making progress toward a version of the capabilities that can be used to engage end users. Demonstration of capabilities continues to be implemented through working groups. Three different working groups, one focused on EM problems in the deep vadose zone, another investigating attenuation mechanisms for metals and radionuclides, and a third focusing on waste tank performance assessment, continue to make progress. The project

Design of capability measurement instruments pedagogic content knowledge (PCK) for prospective mathematics teachers

Science.gov (United States)

Aminah, N.; Wahyuni, I.

2018-05-01

The purpose of this study is to find out how the process of designing a tool of measurement Pedagogical Content Knowledge (PCK) capabilities, especially for prospective mathematics teachers are valid and practical. The design study of this measurement appliance uses modified Plomp development step, which consists of (1) initial assessment stage, (2) design stage at this stage, the researcher designs the measuring grille of PCK capability, (3) realization stage that is making measurement tool ability of PCK, (4) test phase, evaluation, and revision that is testing validation of measurement tools conducted by experts. Based on the results obtained that the design of PCK capability measurement tool is valid as indicated by the assessment of expert validator, and the design of PCK capability measurement tool, shown based on the assessment of teachers and lecturers as users of states strongly agree the design of PCK measurement tools can be used.

Assessment of oscillatory stability constrained available transfer capability

International Nuclear Information System (INIS)

Jain, T.; Singh, S.N.; Srivastava, S.C.

2009-01-01

This paper utilizes a bifurcation approach to compute oscillatory stability constrained available transfer capability (ATC) in an electricity market having bilateral as well as multilateral transactions. Oscillatory instability in non-linear systems can be related to Hopf bifurcation. At the Hopf bifurcation, one pair of the critical eigenvalues of the system Jacobian reaches imaginary axis. A new optimization formulation, including Hopf bifurcation conditions, has been developed in this paper to obtain the dynamic ATC. An oscillatory stability based contingency screening index, which takes into account the impact of transactions on severity of contingency, has been utilized to identify critical contingencies to be considered in determining ATC. The proposed method has been applied for dynamic ATC determination on a 39-bus New England system and a practical 75-bus Indian system considering composite static load as well as dynamic load models. (author)

Assessment of Prediction Capabilities of COCOSYS and CFX Code for Simplified Containment

Directory of Open Access Journals (Sweden)

Jia Zhu

2016-01-01

Full Text Available The acceptable accuracy for simulation of severe accident scenarios in containments of nuclear power plants is required to investigate the consequences of severe accidents and effectiveness of potential counter measures. For this purpose, the actual capability of CFX tool and COCOSYS code is assessed in prototypical geometries for simplified physical process-plume (due to a heat source under adiabatic and convection boundary condition, respectively. Results of the comparison under adiabatic boundary condition show that good agreement is obtained among the analytical solution, COCOSYS prediction, and CFX prediction for zone temperature. The general trend of the temperature distribution along the vertical direction predicted by COCOSYS agrees with the CFX prediction except in dome, and this phenomenon is predicted well by CFX and failed to be reproduced by COCOSYS. Both COCOSYS and CFX indicate that there is no temperature stratification inside dome. CFX prediction shows that temperature stratification area occurs beneath the dome and away from the heat source. Temperature stratification area under adiabatic boundary condition is bigger than that under convection boundary condition. The results indicate that the average temperature inside containment predicted with COCOSYS model is overestimated under adiabatic boundary condition, while it is underestimated under convection boundary condition compared to CFX prediction.

Targeting Insulin-Like Growth Factor 1 Receptor Inhibits Pancreatic Cancer Growth and Metastasis

Science.gov (United States)

Subramani, Ramadevi; Lopez-Valdez, Rebecca; Arumugam, Arunkumar; Nandy, Sushmita; Boopalan, Thiyagarajan; Lakshmanaswamy, Rajkumar

2014-01-01

Pancreatic cancer is one of the most lethal cancers. Increasing incidence and mortality indicates that there is still much lacking in detection and management of the disease. This is partly due to a lack of specific symptoms during early stages of the disease. Several growth factor receptors have been associated with pancreatic cancer. Here, we have investigated if an RNA interference approach targeted to IGF-IR could be effective and efficient against pancreatic cancer growth and metastasis. For that, we evaluated the effects of IGF-1R inhibition using small interfering RNA (siRNAs) on tumor growth and metastasis in HPAC and PANC-1 pancreatic cancer cell lines. We found that silencing IGF-1R inhibits pancreatic cancer growth and metastasis by blocking key signaling pathways such AKT/PI3K, MAPK, JAK/STAT and EMT. Silencing IGF-1R resulted in an anti-proliferative effect in PANC-1 and HPAC pancreatic cancer cell lines. Matrigel invasion, transwell migration and wound healing assays also revealed a role for IGF-1R in metastatic properties of pancreatic cancer. These results were further confirmed using Western blotting analysis of key intermediates involved in proliferation, epithelial mesenchymal transition, migration, and invasion. In addition, soft agar assays showed that silencing IGF-1R also blocks the colony forming capabilities of pancreatic cancer cells in vitro. Western blots, as well as, flow cytometric analysis revealed the induction of apoptosis in IGF-1R silenced cells. Interestingly, silencing IGF-1R also suppressed the expression of insulin receptor β. All these effects together significantly control pancreatic cancer cell growth and metastasis. To conclude, our results demonstrate the significance of IGF-1R in pancreatic cancer. PMID:24809702

Technological capability assessment of suppliers to support product development: case study on a buses and coaches manufacturer

Directory of Open Access Journals (Sweden)

Lucas Comerlato

2013-05-01

Full Text Available Supply chain management has become a critical issue in the global collaboration scenario. Suppliers are not expected to provide just commodities or pre-defined components, but also collaborative engineering design solutions within the product development cycle. Thus, the selection criteria for defining supply partner go beyond the production and logistic capabilities, but must also include technical and engineering competence. This, in some sense, can be considered a common scenario of big companies, but is still challenging when dealing with SME´s. This work discusses how SME´s can be included in a supply chains taking in consideration a set of parameters to assess their technical competence related to product development collaboration. A set of eight parameters has been proposed to assess the engineering team competence, physical and technological structure and further legal responsibility. For each parameter values and weights were defined also. The assessment was applied to three companies that are suppliers of a buses and coaches manufacturer from Rio Grande do Sul, Brazil. The results show that even when dealing with objective parameters, the suppliers and costumer can have different perceptions about same issues.

Dynamic capabilities and innovation capabilities: The case of the ‘Innovation Clinic’

Directory of Open Access Journals (Sweden)

Fred Strønen

2017-01-01

Full Text Available In this explorative study, we investigate the relationship between dynamic capabilities and innovation capabilities. Dynamic capabilities are at the core of strategic management in terms of how firms can ensure adaptation to changing environments over time. Our paper follows two paths of argumentation. First, we review and discuss some major contributions to the theories on ordinary capabilities, dynamic capabilities, and innovation capabilities. We seek to identify different understandings of the concepts in question, in order to clarify the distinctions and relationships between dynamic capabilities and innovation capabilities. Second, we present a case study of the ’Innovation Clinic’ at a major university hospital, including four innovation projects. We use this case study to explore and discuss how dynamic capabilities can be extended, as well as to what extent innovation capabilities can be said to be dynamic. In our conclusion, we discuss the conditions for nurturing ‘dynamic innovation capabilities’ in organizations.

Predictive Capability Maturity Model for computational modeling and simulation.

Energy Technology Data Exchange (ETDEWEB)

Oberkampf, William Louis; Trucano, Timothy Guy; Pilch, Martin M.

2007-10-01

The Predictive Capability Maturity Model (PCMM) is a new model that can be used to assess the level of maturity of computational modeling and simulation (M&S) efforts. The development of the model is based on both the authors experience and their analysis of similar investigations in the past. The perspective taken in this report is one of judging the usefulness of a predictive capability that relies on the numerical solution to partial differential equations to better inform and improve decision making. The review of past investigations, such as the Software Engineering Institute's Capability Maturity Model Integration and the National Aeronautics and Space Administration and Department of Defense Technology Readiness Levels, indicates that a more restricted, more interpretable method is needed to assess the maturity of an M&S effort. The PCMM addresses six contributing elements to M&S: (1) representation and geometric fidelity, (2) physics and material model fidelity, (3) code verification, (4) solution verification, (5) model validation, and (6) uncertainty quantification and sensitivity analysis. For each of these elements, attributes are identified that characterize four increasing levels of maturity. Importantly, the PCMM is a structured method for assessing the maturity of an M&S effort that is directed toward an engineering application of interest. The PCMM does not assess whether the M&S effort, the accuracy of the predictions, or the performance of the engineering system satisfies or does not satisfy specified application requirements.

Capability ethics

OpenAIRE

Robeyns, Ingrid

2012-01-01

textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological theories, virtue ethics, or pragmatism. As I will argue in this chapter, at present the core of the capability approach is an account of value, which together with some other (more minor) normative comm...

Assessment on the capability of quasi-optical grill to launch lower hybrid waves in iter plasma. UE contribution

International Nuclear Information System (INIS)

Santini, F.; Preinhaelter, J.

1998-12-01

The quasi-optical grill has been considered as a convenient system to launch Lower Hybrid Waves in a reactor-like plasma. In recent years, efforts to study the capability and the efficiency of this launcher have been done in Europe with the intent to test it in a large experimental device. Even if this test is still missing, a wide analysis of different schemes of such a launcher is now available in the literature. This report is devoted to critically review this theoretical analysis and consequently to assess the convenience of using quasi-optical grill in future Tokamaks [it

Evolving Capabilities for Virtual Globes

Science.gov (United States)

Glennon, A.

2006-12-01

Though thin-client spatial visualization software like Google Earth and NASA World Wind enjoy widespread popularity, a common criticism is their general lack of analytical functionality. This concern, however, is rapidly being addressed; standard and advanced geographic information system (GIS) capabilities are being developed for virtual globes--though not centralized into a single implementation or software package. The innovation is mostly originating from the user community. Three such capabilities relevant to the earth science, education, and emergency management communities are modeling dynamic spatial phenomena, real-time data collection and visualization, and multi-input collaborative databases. Modeling dynamic spatial phenomena has been facilitated through joining virtual globe geometry definitions--like KML--to relational databases. Real-time data collection uses short scripts to transform user-contributed data into a format usable by virtual globe software. Similarly, collaborative data collection for virtual globes has become possible by dynamically referencing online, multi-person spreadsheets. Examples of these functions include mapping flows within a karst watershed, real-time disaster assessment and visualization, and a collaborative geyser eruption spatial decision support system. Virtual globe applications will continue to evolve further analytical capabilities, more temporal data handling, and from nano to intergalactic scales. This progression opens education and research avenues in all scientific disciplines.

Gossiping Capabilities

DEFF Research Database (Denmark)

Mogensen, Martin; Frey, Davide; Guerraoui, Rachid

Gossip-based protocols are now acknowledged as a sound basis to implement collaborative high-bandwidth content dissemination: content location is disseminated through gossip, the actual contents being subsequently pulled. In this paper, we present HEAP, HEterogeneity Aware gossip Protocol, where...... nodes dynamically adjust their contribution to gossip dissemination according to their capabilities. Using a continuous, itself gossip-based, approximation of relative capabilities, HEAP dynamically leverages the most capable nodes by (a) increasing their fanouts (while decreasing by the same proportion...... declare a high capability in order to augment their perceived quality without contributing accordingly. We evaluate HEAP in the context of a video streaming application on a 236 PlanetLab nodes testbed. Our results shows that HEAP improves the quality of the streaming by 25% over a standard gossip...

The Greater Sekhukhune-CAPABILITY outreach project.

Science.gov (United States)

Gregersen, Nerine; Lampret, Julie; Lane, Tony; Christianson, Arnold

2013-07-01

The Greater Sekhukhune-CAPABILITY Outreach Project was undertaken in a rural district in Limpopo, South Africa, as part of the European Union-funded CAPABILITY programme to investigate approaches for capacity building for the translation of genetic knowledge into care and prevention of congenital disorders. Based on previous experience of a clinical genetic outreach programme in Limpopo, it aimed to initiate a district clinical genetic service in Greater Sekhukhune to gain knowledge and experience to assist in the implementation and development of medical genetic services in South Africa. Implementing the service in Greater Sekhukhune was impeded by a developing staff shortage in the province and pressure on the health service from the existing HIV/AIDS and TB epidemics. This situation underscores the need for health needs assessment for developing services for the care and prevention of congenital disorders in middle- and low-income countries. However, these impediments stimulated the pioneering of innovate ways to offer medical genetic services in these circumstances, including tele-teaching of nurses and doctors, using cellular phones to enhance clinical care and adapting and assessing the clinical utility of a laboratory test, QF-PCR, for use in the local circumstances.

Mobile Smog Simulator: New Capabilities to Study Urban Mixtures

Science.gov (United States)

A smog simulator developed by EPA scientists and engineers has unique capabilities that will provide information for assessing the health impacts of relevant multipollutant atmospheres and identify contributions of specific sources.

Rights, goals, and capabilities

NARCIS (Netherlands)

van Hees, M.V.B.P.M

This article analyses the relationship between rights and capabilities in order to get a better grasp of the kind of consequentialism that the capability theory represents. Capability rights have been defined as rights that have a capability as their object (rights to capabilities). Such a

Irrigation Capability Evaluation of Illushi Floodplain, Edo State, Nigeria

Directory of Open Access Journals (Sweden)

A.S. Umweni

2014-06-01

Full Text Available Many irrigation projects, especially in the developing tropical regions, are embarked upon without any land capability assessment, resulting in avoidable and undesirable ecological consequences. The aim of this study is to assess the irrigation capability potentials of the soils of a rice growing Illushi/Ega community in Edo State of Nigeria. Soils of Illushi/Ega (200 ha were studied to establish their irrigation capabilities. Water samples were collected from the rivers within and near the sites at the proposed points of intake structures and analyzed for salinity (ECw, permeability (SAR and ion toxicity [Chlorine (Cl and Boron (B]. Gravity irrigation suitability assessment was carried out following the guidelines of the United States Bureau for Land Reclamation (USBR, 1953 and FAO (1979. Results showed that about 5.5 % of the land was non-irrigable, 11.5 % was marginally irrigable, 30.5% was moderately irrigable and 52.5 % highly irrigable.Thus about 83 % of the total land area was found to be irrigable. The results of analyses of irrigation water [ECw, SAR and Cl and B (ion toxicity problems in water sources were 0.1 – 0.7 dS m-1, 1.2 – 1.7, 0.6 – 1.8 cmol kg-1 and 0.5 – 0.7 mg kg-1] also show that there is no indication of salinity or ion toxicity problem.

Comparison of capability of dynamic O2-enhanced MRI and quantitative thin-section MDCT to assess COPD in smokers

International Nuclear Information System (INIS)

Ohno, Yoshiharu; Koyama, Hisanobu; Yoshikawa, Takeshi; Matsumoto, Keiko; Aoyama, Nobukazu; Onishi, Yumiko; Takenaka, Daisuke; Matsumoto, Sumiaki; Nishimura, Yoshihiro; Sugimura, Kazuro

2012-01-01

Purpose: The purpose of this study was to directly and prospectively compare the capability of dynamic O 2 -enhanced MRI and quantitatively assessed thin-section MDCT to assess smokers’ COPD in a large prospective cohort. Materials and methods: The GOLD criteria for smokers were used to classify 187 smokers into four clinical stage groups as follows: smokers without COPD (n = 56) and with mild (n = 54), moderate (n = 52) and severe or very severe COPD (n = 24). All smokers underwent dynamic O 2 -enhanced MRI, MDCT and pulmonary function tests. Mean relative enhancement ratio and mean wash-in time on MRI and CT-based functional lung volume (CT-based FLV) as well as the ratio of airway wall area to total airway area on MDCT were computationally calculated. Then, all indexes were significantly correlated with functional parameters. To determine the efficacy of all indexes for clinical stage classification, the indexes for the four clinical groups were statistically compared by using Tukey's honestly significant difference multiple comparison test. Results: All indexes had significant correlations with functional parameters (p 2 -enhanced MRI for assessment of COPD in smokers is potentially as efficacious as quantitatively assessed thin-section MDCT.

Frameworks for Assessing the Quality of Modeling and Simulation Capabilities

Science.gov (United States)

Rider, W. J.

2012-12-01

The importance of assuring quality in modeling and simulation has spawned several frameworks for structuring the examination of quality. The format and content of these frameworks provides an emphasis, completeness and flow to assessment activities. I will examine four frameworks that have been developed and describe how they can be improved and applied to a broader set of high consequence applications. Perhaps the first of these frameworks was known as CSAU [Boyack] (code scaling, applicability and uncertainty) used for nuclear reactor safety and endorsed the United States' Nuclear Regulatory Commission (USNRC). This framework was shaped by nuclear safety practice, and the practical structure needed after the Three Mile Island accident. It incorporated the dominant experimental program, the dominant analysis approach, and concerns about the quality of modeling. The USNRC gave it the force of law that made the nuclear industry take it seriously. After the cessation of nuclear weapons' testing the United States began a program of examining the reliability of these weapons without testing. This program utilizes science including theory, modeling, simulation and experimentation to replace the underground testing. The emphasis on modeling and simulation necessitated attention on the quality of these simulations. Sandia developed the PCMM (predictive capability maturity model) to structure this attention [Oberkampf]. PCMM divides simulation into six core activities to be examined and graded relative to the needs of the modeling activity. NASA [NASA] has built yet another framework in response to the tragedy of the space shuttle accidents. Finally, Ben-Haim and Hemez focus upon modeling robustness and predictive fidelity in another approach. These frameworks are similar, and applied in a similar fashion. The adoption of these frameworks at Sandia and NASA has been slow and arduous because the force of law has not assisted acceptance. All existing frameworks are

User Instructions for the Systems Assessment Capability, Rev. 0, Computer Codes Volume 1: Inventory, Release, and Transport Modules

International Nuclear Information System (INIS)

Eslinger, Paul W.; Engel, David W.; Gerhardstein, Lawrence H.; Lopresti, Charles A.; Nichols, William E.; Strenge, Dennis L.

2001-12-01

One activity of the Department of Energy's Groundwater/Vadose Zone Integration Project is an assessment of cumulative impacts from Hanford Site wastes on the subsurface environment and the Columbia River. Through the application of a system assessment capability (SAC), decisions for each cleanup and disposal action will be able to take into account the composite effect of other cleanup and disposal actions. The SAC has developed a suite of computer programs to simulate the migration of contaminants (analytes) present on the Hanford Site and to assess the potential impacts of the analytes, including dose to humans, socio-cultural impacts, economic impacts, and ecological impacts. The general approach to handling uncertainty in the SAC computer codes is a Monte Carlo approach. Conceptually, one generates a value for every stochastic parameter in the code (the entire sequence of modules from inventory through transport and impacts) and then executes the simulation, obtaining an output value, or result. This document provides user instructions for the SAC codes that handle inventory tracking, release of contaminants to the environment, and transport of contaminants through the unsaturated zone, saturated zone, and the Columbia River

Capability ethics

NARCIS (Netherlands)

I.A.M. Robeyns (Ingrid)

2012-01-01

textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological

National power grid simulation capability : need and issues

Energy Technology Data Exchange (ETDEWEB)

Petri, Mark C. [Argonne National Lab. (ANL), Argonne, IL (United States)

2009-06-02

On December 9 and 10, 2008, the Department of Homeland Security (DHS) Science and Technology Directorate sponsored a national workshop at Argonne National Laboratory to explore the need for a comprehensive modeling and simulation capability for the national electric power grid system. The workshop brought together leading electric power grid experts from federal agencies, the national laboratories, and academia to discuss the current state of power grid science and engineering and to assess if important challenges are being met. The workshop helped delineate gaps between grid needs and current capabilities and identify issues that must be addressed if a solution is to be implemented. This report is a result of the workshop and highlights power grid modeling and simulation needs, the barriers that must be overcome to address them, and the benefits of a national power grid simulation capability.

Assessment of Coping Capability of KORI Unit 1 under Extended Loss AC Power and Loss of Ultimate Heat Sink Initiated by Beyond Design Natural Disaster

Energy Technology Data Exchange (ETDEWEB)

Kim, Chang Hyun; Ha, Sang Jun [KHNP CRI, Daejeon (Korea, Republic of); Han, Kee Soo [Nuclear Engineering Service and Solution (NESS) Co. Ltd., Deajeon (Korea, Republic of); Park, Chan Eok [KEPCO Engineering and Constructd., Deajeon (Korea, Republic of)

2016-10-15

In Korea, the government and industry performed comprehensive safety inspection on all domestic nuclear power plants against beyond design basis external events and fifty action items have been issued. In addition to post- Fukushima action items, the stress tests for all domestic nuclear power plants are on the way to enhance the safety of domestic nuclear power plants through finding the vulnerabilities in intentional stress conditions initiated by beyond design natural disaster. This paper presents assessment results of coping capability of KORI Unit 1 under the simultaneous Extended Loss of AC Power (ELAP) and Loss of Ultimate Heat Sink (LUHS) which is a representative plant condition initiated by beyond design natural disaster. The assessment of the coping capability of KORI Unit 1 has been performed under simultaneous the extended loss of AC power and loss of ultimate heat sink initiated by beyond design natural disaster. It is concluded that KORI Unit 1 has the capability, in the event of loss of safety functions by beyond design natural disaster, to sufficiently cool down the reactor core without fuel damage, to keep pressure boundaries of the reactor coolant system in transient condition and to control containment and temperature to maintain the integrity of the containment buildings.

Assessment of Coping Capability of KORI Unit 1 under Extended Loss AC Power and Loss of Ultimate Heat Sink Initiated by Beyond Design Natural Disaster

International Nuclear Information System (INIS)

Kim, Chang Hyun; Ha, Sang Jun; Han, Kee Soo; Park, Chan Eok

2016-01-01

In Korea, the government and industry performed comprehensive safety inspection on all domestic nuclear power plants against beyond design basis external events and fifty action items have been issued. In addition to post- Fukushima action items, the stress tests for all domestic nuclear power plants are on the way to enhance the safety of domestic nuclear power plants through finding the vulnerabilities in intentional stress conditions initiated by beyond design natural disaster. This paper presents assessment results of coping capability of KORI Unit 1 under the simultaneous Extended Loss of AC Power (ELAP) and Loss of Ultimate Heat Sink (LUHS) which is a representative plant condition initiated by beyond design natural disaster. The assessment of the coping capability of KORI Unit 1 has been performed under simultaneous the extended loss of AC power and loss of ultimate heat sink initiated by beyond design natural disaster. It is concluded that KORI Unit 1 has the capability, in the event of loss of safety functions by beyond design natural disaster, to sufficiently cool down the reactor core without fuel damage, to keep pressure boundaries of the reactor coolant system in transient condition and to control containment and temperature to maintain the integrity of the containment buildings

Dynamic Capabilities

DEFF Research Database (Denmark)

Grünbaum, Niels Nolsøe; Stenger, Marianne

2013-01-01

The findings reveal a positive relationship between dynamic capabilities and innovation performance in the case enterprises, as we would expect. It was, however, not possible to establish a positive relationship between innovation performance and profitability. Nor was there any positive...... relationship between dynamic capabilities and profitability....

NRC iterative performance assessment Phase 2. Development of capabilities for review of a performance assessment for a high-level waste repository

International Nuclear Information System (INIS)

Wescott, R.G.; Lee, M.P.; Eisenberg, N.A.; Baca, R.G.

1995-10-01

In order to better review a potential license application to construct and operate a geologic repository for spent nuclear fuel and high-level radioactive waste (HLW), the Nuclear Regulatory Commission staff (and its contractor) has expanded and improved its capability to conduct performance assessments. This report documents the demonstration of the second phase of this capability. The demonstration made use of the scenario selection procedure developed by Sandia National Laboratories to provide a set of scenarios, with corresponding probabilities, for use in the consequence analysis of a potential HLW disposal site in unsaturated tuff. Models of release of radionuclides from the waste form and transport in ground water, air and by direct pathways provided preliminary estimates of releases to the accessible environment for a 10,000 year period. The input values of parameters necessary for the consequence models were sampled numerous times using Latin Hypercube Sampling from assumed probability distributions. The results from the consequence models were then used to generate Complementary Cumulative Distribution Functions (CCDFs) for either release to the accessible environment or effective dose equivalents to a target population. CCDFs were calculated for probabilistically significant combinations (scenarios) of four disruptive events; drilling, pluvial climate, seismicity and magmatism. Sensitivity and uncertainty analyses of the calculated releases and effective dose equivalents were also used to determine the importance of the parameters. Because of the preliminary nature of the analysis and the lack of an adequate data base, the results and conclusions presented in this report should be carefully interpreted. They should not be misconstrued to represent the actual performance of the proposed Yucca Mountain repository nor serve as an endorsement of the methods used

Capabilities and Incapabilities of the Capabilities Approach to Health Justice.

Science.gov (United States)

Selgelid, Michael J

2016-01-01

This first part of this article critiques Sridhar Venkatapuram's conception of health as a capability. It argues that Venkatapuram relies on the problematic concept of dignity, implies that those who are unhealthy lack lives worthy of dignity (which seems politically incorrect), sets a low bar for health, appeals to metaphysically problematic thresholds, fails to draw clear connections between appealed-to capabilities and health, and downplays the importance/relevance of health functioning. It concludes by questioning whether justice entitlements should pertain to the capability for health versus health achievements, challenging Venkatapuram's claims about the strength of health entitlements, and demonstrating that the capabilities approach is unnecessary to address social determinants of health. © 2016 John Wiley & Sons Ltd.

The Capability Approach: A Critical Review of Its Application in Health Economics.

Science.gov (United States)

Karimi, Milad; Brazier, John; Basarir, Hasan

The capability approach is an approach to assessing well-being developed by Amartya Sen. Interest in this approach has resulted in several attempts to develop questionnaires to measure and value capability at an individual level in health economics. This commentary critically reviews the ability of these questionnaires to measure and value capability. It is argued that the method used in the questionnaires to measure capability will result in a capability set that is an inaccurate description of the individual's true capability set. The measured capability set will either represent only one combination and ignore the value of choice in the capability set, or represent one combination that is not actually achievable by the individual. In addition, existing methods of valuing capability may be inadequate because they do not consider that capability is a set. It may be practically more feasible to measure and value capability approximately rather than directly. Suggestions are made on how to measure and value an approximation to capability, but further research is required to implement the suggestions. Copyright © 2016 International Society for Pharmacoeconomics and Outcomes Research (ISPOR). Published by Elsevier Inc. All rights reserved.

Diffusion-weighted MR imaging vs. multi-detector row CT: Direct comparison of capability for assessment of management needs for anterior mediastinal solitary tumors

International Nuclear Information System (INIS)

Seki, Shinichiro; Koyama, Hisanobu; Ohno, Yoshiharu; Nishio, Mizuho; Takenaka, Daisuke; Maniwa, Yoshimasa; Itoh, Tomoo; Nishimura, Yoshihiro; Sugimura, Kazuro

2014-01-01

Purpose: To evaluate and compare the capability of diffusion-weighted MR imaging (DWI) and CT for assessment of management needs for anterior mediastinal solitary tumors. Materials and methods: Thirty-five patients with pathologically confirmed anterior mediastinal tumors were enrolled. The tumors were divided into two groups according to need for management: tumors not needing further intervention or treatment (group A; thymoma type A, AB and B1) and tumors needing further intervention and treatment (group B; other thymoma types and malignancies). The apparent diffusion coefficient (ADC) of each tumor was measured, and probabilities of malignancy and need for further intervention and treatment were visually assessed on CT. The differences in ADCs between group A and B and between malignancies and thymomas in group B were evaluated with the Mann–Whitney's U-test. Feasible threshold values for differentiation of group B from group A and distinguishing malignancies from thymomas assessed as group B were determined by the ROC-based positive test, and McNemar's test was used for comparing diagnostic capabilities of DWI with those of CT. Results: ADCs for the two groups were significantly different (p < 0.001). Application of the threshold value for differentiation of group B from A showed no significant difference (p > 0.05). Application of the feasible threshold value for distinguishing malignant from thymomas assessed as group B showed that specificity (76.9%) and accuracy (85.2%) of DWI were significantly better than those of visual score (p < 0.05). Conclusion: DWI has useful potential for the assessment of management needs for anterior mediastinum solitary tumors as well as CT

Capabilities for Strategic Adaptation

DEFF Research Database (Denmark)

Distel, Andreas Philipp

This dissertation explores capabilities that enable firms to strategically adapt to environmental changes and preserve competitiveness over time – often referred to as dynamic capabilities. While dynamic capabilities being a popular research domain, too little is known about what these capabiliti...

Nitrate reduction in geologically heterogeneous catchments — A framework for assessing the scale of predictive capability of hydrological models

International Nuclear Information System (INIS)

Refsgaard, Jens Christian; Auken, Esben; Bamberg, Charlotte A.; Christensen, Britt S.B.; Clausen, Thomas; Dalgaard, Esben; Effersø, Flemming; Ernstsen, Vibeke; Gertz, Flemming; Hansen, Anne Lausten; He, Xin; Jacobsen, Brian H.; Jensen, Karsten Høgh; Jørgensen, Flemming; Jørgensen, Lisbeth Flindt; Koch, Julian; Nilsson, Bertel; Petersen, Christian; De Schepper, Guillaume; Schamper, Cyril

2014-01-01

In order to fulfil the requirements of the EU Water Framework Directive nitrate load from agricultural areas to surface water in Denmark needs to be reduced by about 40%. The regulations imposed until now have been uniform, i.e. the same restrictions for all areas independent of the subsurface conditions. Studies have shown that on a national basis about 2/3 of the nitrate leaching from the root zone is reduced naturally, through denitrification, in the subsurface before reaching the streams. Therefore, it is more cost-effective to identify robust areas, where nitrate leaching through the root zone is reduced in the saturated zone before reaching the streams, and vulnerable areas, where no subsurface reduction takes place, and then only impose regulations/restrictions on the vulnerable areas. Distributed hydrological models can make predictions at grid scale, i.e. at much smaller scale than the entire catchment. However, as distributed models often do not include local scale hydrogeological heterogeneities, they are typically not able to make accurate predictions at scales smaller than they are calibrated. We present a framework for assessing nitrate reduction in the subsurface and for assessing at which spatial scales modelling tools have predictive capabilities. A new instrument has been developed for airborne geophysical measurements, Mini-SkyTEM, dedicated to identifying geological structures and heterogeneities with horizontal and lateral resolutions of 30–50 m and 2 m, respectively, in the upper 30 m. The geological heterogeneity and uncertainty are further analysed by use of the geostatistical software TProGS by generating stochastic geological realisations that are soft conditioned against the geophysical data. Finally, the flow paths within the catchment are simulated by use of the MIKE SHE hydrological modelling system for each of the geological models generated by TProGS and the prediction uncertainty is characterised by the variance between the

Nitrate reduction in geologically heterogeneous catchments — A framework for assessing the scale of predictive capability of hydrological models

Energy Technology Data Exchange (ETDEWEB)

Refsgaard, Jens Christian, E-mail: jcr@geus.dk [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Auken, Esben [Department of Earth Sciences, Aarhus University (Denmark); Bamberg, Charlotte A. [City of Aarhus (Denmark); Christensen, Britt S.B. [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Clausen, Thomas [DHI, Hørsholm (Denmark); Dalgaard, Esben [Department of Earth Sciences, Aarhus University (Denmark); Effersø, Flemming [SkyTEM Aps, Beder (Denmark); Ernstsen, Vibeke [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Gertz, Flemming [Knowledge Center for Agriculture, Skejby (Denmark); Hansen, Anne Lausten [Department of Geosciences and Natural Resource Management, University of Copenhagen (Denmark); He, Xin [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Jacobsen, Brian H. [Department of Food and Resource Economics, University of Copenhagen (Denmark); Jensen, Karsten Høgh [Department of Geosciences and Natural Resource Management, University of Copenhagen (Denmark); Jørgensen, Flemming; Jørgensen, Lisbeth Flindt [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Koch, Julian [Department of Geosciences and Natural Resource Management, University of Copenhagen (Denmark); Nilsson, Bertel [Geological Survey of Denmark and Greenland (GEUS) (Denmark); Petersen, Christian [City of Odder (Denmark); De Schepper, Guillaume [Université Laval, Québec (Canada); Schamper, Cyril [Department of Earth Sciences, Aarhus University (Denmark); and others

2014-01-01

In order to fulfil the requirements of the EU Water Framework Directive nitrate load from agricultural areas to surface water in Denmark needs to be reduced by about 40%. The regulations imposed until now have been uniform, i.e. the same restrictions for all areas independent of the subsurface conditions. Studies have shown that on a national basis about 2/3 of the nitrate leaching from the root zone is reduced naturally, through denitrification, in the subsurface before reaching the streams. Therefore, it is more cost-effective to identify robust areas, where nitrate leaching through the root zone is reduced in the saturated zone before reaching the streams, and vulnerable areas, where no subsurface reduction takes place, and then only impose regulations/restrictions on the vulnerable areas. Distributed hydrological models can make predictions at grid scale, i.e. at much smaller scale than the entire catchment. However, as distributed models often do not include local scale hydrogeological heterogeneities, they are typically not able to make accurate predictions at scales smaller than they are calibrated. We present a framework for assessing nitrate reduction in the subsurface and for assessing at which spatial scales modelling tools have predictive capabilities. A new instrument has been developed for airborne geophysical measurements, Mini-SkyTEM, dedicated to identifying geological structures and heterogeneities with horizontal and lateral resolutions of 30–50 m and 2 m, respectively, in the upper 30 m. The geological heterogeneity and uncertainty are further analysed by use of the geostatistical software TProGS by generating stochastic geological realisations that are soft conditioned against the geophysical data. Finally, the flow paths within the catchment are simulated by use of the MIKE SHE hydrological modelling system for each of the geological models generated by TProGS and the prediction uncertainty is characterised by the variance between the

Assessment of capabilities and research needs in the area of health effects of low-level ionizing radiation. A joint report to the Congress

International Nuclear Information System (INIS)

1979-08-01

The report summarizes the capabilities, research needs and on-going projects of the Environmental Protection Agency and the Nuclear Regulatory Commission related to the health effects of low-level ionizing radiation. The statutory authorities of both EPA and NRC related to radiation protection and radiation research are also briefly described. An introductory general section describes current efforts to improve Federal radiation research and general methods used by both agencies for radiation dose assessment and the estimation of the potential health effects of low-level ionizing radiation. Separate sections describe the respective authorities, needs, capabilities, and current research programs of the two agencies. The report was prepared to fulfill a requirement by the US Congress which is contained in Section 5(c) of Public Law 95-601

Analysis of drug-protein binding using on-line immunoextraction and high-performance affinity microcolumns: Studies with normal and glycated human serum albumin.

Science.gov (United States)

Matsuda, Ryan; Jobe, Donald; Beyersdorf, Jared; Hage, David S

2015-10-16

A method combining on-line immunoextraction microcolumns with high-performance affinity chromatography (HPAC) was developed and tested for use in examining drug-protein interactions with normal or modified proteins. Normal human serum albumin (HSA) and glycated HSA were used as model proteins for this work. High-performance immunoextraction microcolumns with sizes of 1.0-2.0 cm × 2.1mm i.d. and containing anti-HSA polyclonal antibodies were developed and tested for their ability to bind normal HSA or glycated HSA. These microcolumns were able to extract up to 82-93% for either type of protein at 0.05-0.10 mL/min and had a binding capacity of 0.34-0.42 nmol HSA for a 1.0 cm × 2.1mm i.d. microcolumn. The immunoextraction microcolumns and their adsorbed proteins were tested for use in various approaches for drug binding studies. Frontal analysis was used with the adsorbed HSA/glycated HSA to measure the overall affinities of these proteins for the drugs warfarin and gliclazide, giving comparable values to those obtained previously using similar protein preparations that had been covalently immobilized within HPAC columns. Zonal elution competition studies with gliclazide were next performed to examine the specific interactions of this drug at Sudlow sites I and II of the adsorbed proteins. These results were also comparable to those noted in prior work with covalently immobilized samples of normal HSA or glycated HSA. These experiments indicated that drug-protein binding studies can be carried out by using on-line immunoextraction microcolumns with HPAC. The same method could be used in the future with clinical samples and other drugs or proteins of interest in pharmaceutical studies or biomedical research. Copyright © 2015 Elsevier B.V. All rights reserved.

ARAC: A support capability for emergency managers

Energy Technology Data Exchange (ETDEWEB)

Pace, J.C.; Sullivan, T.J.; Baskett, R.L. [and others

1995-08-01

This paper is intended to introduce to the non-radiological emergency management community the 20-year operational history of the Atmospheric Release Advisory Capability (ARAC), its concept of operations, and its applicability for use in support of emergency management decision makers. ARAC is a centralized federal facility for assessing atmospheric releases of hazardous materials in real time, using a robust suite of three-dimensional atmospheric transport and diffusion models, extensive geophysical and source-description databases, automated meteorological data acquisition systems, and experienced staff members. Although originally conceived to respond to nuclear accidents, the ARAC system has proven to be extremely adaptable, and has been used successfully during a wide variety of nonradiological hazardous chemical situations. ARAC represents a proven, validated, operational support capability for atmospheric hazardous releases.

Performance assessment of mass flow rate measurement capability in a large scale transient two-phase flow test system

International Nuclear Information System (INIS)

Nalezny, C.L.; Chapman, R.L.; Martinell, J.S.; Riordon, R.P.; Solbrig, C.W.

1979-01-01

Mass flow is an important measured variable in the Loss-of-Fluid Test (LOFT) Program. Large uncertainties in mass flow measurements in the LOFT piping during LOFT coolant experiments requires instrument testing in a transient two-phase flow loop that simulates the geometry of the LOFT piping. To satisfy this need, a transient two-phase flow loop has been designed and built. The load cell weighing system, which provides reference mass flow measurements, has been analyzed to assess its capability to provide the measurements. The analysis consisted of first performing a thermal-hydraulic analysis using RELAP4 to compute mass inventory and pressure fluctuations in the system and mass flow rate at the instrument location. RELAP4 output was used as input to a structural analysis code SAPIV which is used to determine load cell response. The computed load cell response was then smoothed and differentiated to compute mass flow rate from the system. Comparison between computed mass flow rate at the instrument location and mass flow rate from the system computed from the load cell output was used to evaluate mass flow measurement capability of the load cell weighing system. Results of the analysis indicate that the load cell weighing system will provide reference mass flows more accurately than the instruments now in LOFT

Capability Assessment and Performance Metrics for the Titan Multispectral Mapping Lidar

Directory of Open Access Journals (Sweden)

Juan Carlos Fernandez-Diaz

2016-11-01

Full Text Available In this paper we present a description of a new multispectral airborne mapping light detection and ranging (lidar along with performance results obtained from two years of data collection and test campaigns. The Titan multiwave lidar is manufactured by Teledyne Optech Inc. (Toronto, ON, Canada and emits laser pulses in the 1550, 1064 and 532 nm wavelengths simultaneously through a single oscillating mirror scanner at pulse repetition frequencies (PRF that range from 50 to 300 kHz per wavelength (max combined PRF of 900 kHz. The Titan system can perform simultaneous mapping in terrestrial and very shallow water environments and its multispectral capability enables new applications, such as the production of false color active imagery derived from the lidar return intensities and the automated classification of target and land covers. Field tests and mapping projects performed over the past two years demonstrate capabilities to classify five land covers in urban environments with an accuracy of 90%, map bathymetry under more than 15 m of water, and map thick vegetation canopies at sub-meter vertical resolutions. In addition to its multispectral and performance characteristics, the Titan system is designed with several redundancies and diversity schemes that have proven to be beneficial for both operations and the improvement of data quality.

Integrated FDG-PET/CT vs. standard radiological examinations: Comparison of capability for assessment of postoperative recurrence in non-small cell lung cancer patients

International Nuclear Information System (INIS)

Takenaka, Daisuke; Ohno, Yoshiharu; Koyama, Hisanobu; Nogami, Munenobu; Onishi, Yumiko; Matsumoto, Keiko; Matsumoto, Sumiaki; Yoshikawa, Takeshi; Sugimura, Kazuro

2010-01-01

Purpose: The purpose of this study was to prospectively and directly compare diagnostic capabilities of whole-body integrated FDG-PET/CT and standard radiologic examination for assessment of recurrence in postoperative non-small cell lung cancer (NSCLC) patients. Materials and methods: A total of 92 consecutive pathologically diagnosed NSCLC patients (65 males, 27 females; mean age, 71 years) underwent pathologically and surgically proven complete resection, followed by prospective whole-body FDG-PET/CT and standard radiological examinations. Final diagnosis of recurrence was based on the results of more than 1 year of follow-up and/or pathological examinations. On both methods, the probability of recurrence was assessed in each patient by using a five-point visual scoring system, and the each final diagnosis was made by consensus between two readers. Kappa analyses were performed to determine inter-observer agreement for both methods, and ROC analyses were used to compare capability of the two methods for assessment of postoperative recurrence on a per-patient basis. Sensitivity, specificity and accuracy were also compared between PET/CT and standard radiological examination by means of McNemar's test. Results: All inter-observer agreements were almost perfect (integrated PET/CT: κ = 0.89; standard radiological examination: κ = 0.81). There were no statistically significant differences in area under the curve, sensitivity, specificity and accuracy between integrated FDG-PET/CT and standard radiologic examinations (p > 0.05). Conclusion: Integrated FDG-PET/CT can be used for assessment of postoperative recurrence in NSCLC patients with accuracy as good as that of standard radiological examinations.

Integrated FDG-PET/CT vs. standard radiological examinations: Comparison of capability for assessment of postoperative recurrence in non-small cell lung cancer patients

Energy Technology Data Exchange (ETDEWEB)

Takenaka, Daisuke [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Ohno, Yoshiharu, E-mail: yosirad@kobe-u.ac.j [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Koyama, Hisanobu [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Nogami, Munenobu [Division of Image-Based Medicine, Institute of Biomedical Research and Innovation, 2-2, Minatojima Minamimachi Chuo-ku, Kobe, Hyogo 650-0047 (Japan); Onishi, Yumiko; Matsumoto, Keiko [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Matsumoto, Sumiaki [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan); Department of Radiology, University of Yamanashi, 1110 Shimogato, Chuo, Yamanashi, 409-3898 (Japan); Yoshikawa, Takeshi; Sugimura, Kazuro [Department of Radiology, Kobe University Graduate School of Medicine, 7-5-2 Kusunoki-cho, Chuo-ku, Kobe, Hyogo 650-0017 (Japan)

2010-06-15

Purpose: The purpose of this study was to prospectively and directly compare diagnostic capabilities of whole-body integrated FDG-PET/CT and standard radiologic examination for assessment of recurrence in postoperative non-small cell lung cancer (NSCLC) patients. Materials and methods: A total of 92 consecutive pathologically diagnosed NSCLC patients (65 males, 27 females; mean age, 71 years) underwent pathologically and surgically proven complete resection, followed by prospective whole-body FDG-PET/CT and standard radiological examinations. Final diagnosis of recurrence was based on the results of more than 1 year of follow-up and/or pathological examinations. On both methods, the probability of recurrence was assessed in each patient by using a five-point visual scoring system, and the each final diagnosis was made by consensus between two readers. Kappa analyses were performed to determine inter-observer agreement for both methods, and ROC analyses were used to compare capability of the two methods for assessment of postoperative recurrence on a per-patient basis. Sensitivity, specificity and accuracy were also compared between PET/CT and standard radiological examination by means of McNemar's test. Results: All inter-observer agreements were almost perfect (integrated PET/CT: {kappa} = 0.89; standard radiological examination: {kappa} = 0.81). There were no statistically significant differences in area under the curve, sensitivity, specificity and accuracy between integrated FDG-PET/CT and standard radiologic examinations (p > 0.05). Conclusion: Integrated FDG-PET/CT can be used for assessment of postoperative recurrence in NSCLC patients with accuracy as good as that of standard radiological examinations.

Transportation capabilities of the existing cask fleet

International Nuclear Information System (INIS)

Johnson, P.E.; Wankerl, M.W.; Joy, D.S.

1991-01-01

This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 465 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the DOE consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated

Transportation capabilities of the existing cask fleet

International Nuclear Information System (INIS)

Johnson, P.E.; Joy, D.S.; Wankerl, M.W.

1991-01-01

This paper describes a number of scenarios estimating the amount of spent nuclear fuel that could be transported to a Monitored Retrievable Storage (MRS) Facility by various combinations of existing cask fleets. To develop the scenarios, the data provided by the Transportation System Data Base (TSDB) were modified to reflect the additional time for cask turnaround resulting from various startup and transportation issues. With these more realistic speed and cask-handling assumptions, the annual transportation capability of a fleet consisting of all of the existing casks is approximately 46 metric tons of uranium (MTU). The most likely fleet of existing casks that would be made available to the Department of Energy (DOE) consists of two rail, three overweight truck, and six legal weight truck casks. Under the same transportation assumptions, this cask fleet is capable of approximately transporting 270 MTU/year. These ranges of capability is a result of the assumptions pertaining to the number of casks assumed to be available. It should be noted that this assessment assumes additional casks based on existing certifications are not fabricated. 5 refs., 4 tabs

Does organizational agility affect organizational learning capability? Evidence from commercial banking

OpenAIRE

Zaina Mustafa Mahmoud Hamad; Uğur Yozgat

2017-01-01

Both organizational agility and learning capability are prerequisites for organizational survival and success. This study explores the contribution of agility practices to organizational learning capabilities at the commercial banks in Jordan. To examine the proposed model, a sample of 158 employees within top and middle managements was used. Structural Equation Modeling was conducted for assessing validity and reliability of measurement instrument, evaluating model fit, and testing hypothese...

Fusion Materials Irradiation Test Facility: experimental capabilities and test matrix

International Nuclear Information System (INIS)

Opperman, E.K.

1982-01-01

This report describes the experimental capabilities of the Fusion Materials Irradiation Test Facility (FMIT) and reference material specimen test matrices. The description of the experimental capabilities and the test matrices has been updated to match the current single test cell facility ad assessed experimenter needs. Sufficient detail has been provided so that the user can plan irradiation experiments and conceptual hardware. The types of experiments, irradiation environment and support services that will be available in FMIT are discussed

Decision making in prioritization of required operational capabilities

Science.gov (United States)

Andreeva, P.; Karev, M.; Kovacheva, Ts.

2015-10-01

The paper describes an expert heuristic approach to prioritization of required operational capabilities in the field of defense. Based on expert assessment and by application of the method of Analytical Hierarchical Process, a methodology for their prioritization has been developed. It has been applied to practical simulation decision making games.

Capability-based computer systems

CERN Document Server

Levy, Henry M

2014-01-01

Capability-Based Computer Systems focuses on computer programs and their capabilities. The text first elaborates capability- and object-based system concepts, including capability-based systems, object-based approach, and summary. The book then describes early descriptor architectures and explains the Burroughs B5000, Rice University Computer, and Basic Language Machine. The text also focuses on early capability architectures. Dennis and Van Horn's Supervisor; CAL-TSS System; MIT PDP-1 Timesharing System; and Chicago Magic Number Machine are discussed. The book then describes Plessey System 25

Software Assessment of the Global Force Management (GFM) Search Capability Study

Science.gov (United States)

2017-02-01

MOS Capability Vector Work 3 3.3 Schema and Database Work Breakdown 4 3.3.1 Overall Generation 4 3.3.2 Algorithm Descriptions 5 3.3.3 Java API...battalion for example) and makes sure the results have a known name (not ‘%NKN’). 3.3.3 Java API Description Generation API call: GenerateAll.run...Database Login Username databaseUsername=root #Database Login Password databasePassword= mysql #Application Database Name appDatabaseName=Simple_GFM

Mobile Test Capabilities

Data.gov (United States)

Federal Laboratory Consortium — The Electrical Power Mobile Test capabilities are utilized to conduct electrical power quality testing on aircraft and helicopters. This capability allows that the...

Power capability evaluation for lithium iron phosphate batteries based on multi-parameter constraints estimation

Science.gov (United States)

Wang, Yujie; Pan, Rui; Liu, Chang; Chen, Zonghai; Ling, Qiang

2018-01-01

The battery power capability is intimately correlated with the climbing, braking and accelerating performance of the electric vehicles. Accurate power capability prediction can not only guarantee the safety but also regulate driving behavior and optimize battery energy usage. However, the nonlinearity of the battery model is very complex especially for the lithium iron phosphate batteries. Besides, the hysteresis loop in the open-circuit voltage curve is easy to cause large error in model prediction. In this work, a multi-parameter constraints dynamic estimation method is proposed to predict the battery continuous period power capability. A high-fidelity battery model which considers the battery polarization and hysteresis phenomenon is presented to approximate the high nonlinearity of the lithium iron phosphate battery. Explicit analyses of power capability with multiple constraints are elaborated, specifically the state-of-energy is considered in power capability assessment. Furthermore, to solve the problem of nonlinear system state estimation, and suppress noise interference, the UKF based state observer is employed for power capability prediction. The performance of the proposed methodology is demonstrated by experiments under different dynamic characterization schedules. The charge and discharge power capabilities of the lithium iron phosphate batteries are quantitatively assessed under different time scales and temperatures.

A case study: application of statistical process control tool for determining process capability and sigma level.

Science.gov (United States)

Chopra, Vikram; Bairagi, Mukesh; Trivedi, P; Nagar, Mona

2012-01-01

Statistical process control is the application of statistical methods to the measurement and analysis of variation process. Various regulatory authorities such as Validation Guidance for Industry (2011), International Conference on Harmonisation ICH Q10 (2009), the Health Canada guidelines (2009), Health Science Authority, Singapore: Guidance for Product Quality Review (2008), and International Organization for Standardization ISO-9000:2005 provide regulatory support for the application of statistical process control for better process control and understanding. In this study risk assessments, normal probability distributions, control charts, and capability charts are employed for selection of critical quality attributes, determination of normal probability distribution, statistical stability, and capability of production processes, respectively. The objective of this study is to determine tablet production process quality in the form of sigma process capability. By interpreting data and graph trends, forecasting of critical quality attributes, sigma process capability, and stability of process were studied. The overall study contributes to an assessment of process at the sigma level with respect to out-of-specification attributes produced. Finally, the study will point to an area where the application of quality improvement and quality risk assessment principles for achievement of six sigma-capable processes is possible. Statistical process control is the most advantageous tool for determination of the quality of any production process. This tool is new for the pharmaceutical tablet production process. In the case of pharmaceutical tablet production processes, the quality control parameters act as quality assessment parameters. Application of risk assessment provides selection of critical quality attributes among quality control parameters. Sequential application of normality distributions, control charts, and capability analyses provides a valid statistical

Building Service Provider Capabilities

DEFF Research Database (Denmark)

Brandl, Kristin; Jaura, Manya; Ørberg Jensen, Peter D.

2015-01-01

In this paper we study whether and how the interaction between clients and the service providers contributes to the development of capabilities in service provider firms. In situations where such a contribution occurs, we analyze how different types of activities in the production process...... process. We find that clients influence the development of human capital capabilities and management capabilities in reciprocally produced services. While in sequential produced services clients influence the development of organizational capital capabilities and management capital capabilities....... of the services, such as sequential or reciprocal task activities, influence the development of different types of capabilities. We study five cases of offshore-outsourced knowledge-intensive business services that are distinguished according to their reciprocal or sequential task activities in their production...

Artificial reef evaluation capabilities of Florida counties

OpenAIRE

Halusky, Joseph G.; Antonini, Gustavo A.; Seaman, William

1993-01-01

Florida's coastal county artificial reef sampling and data management programs are surveyed in this report. The survey describes the county level capability for artificial reef documentation and performance assessment based on their needs, interests, organizational structure and "in-situ" data collection and data management techniques. The. primary purpose of this study is to describe what staffing, training, techniques, organizational procedures and equipment are used by the c...

Effect of quality of family environment on the child's adaptation capabilities

Directory of Open Access Journals (Sweden)

Ivana Kreft

2008-08-01

Full Text Available The aim of the paper was to investigate how the quality of family environment is related to the child's adaptation capabilities. Child's adaptation was evaluated with a special assessment called SPP-3 (Systematic Psychological Assessment of a 3-year Old Child, that screens the population of 3-year olds to look for inadequate adaptation patterns. I assumed that in families where parents have higher education and where the environment is more stimulating children will show more effective and adaptive behaviour. Seventy-five children and parents who attended the psychological assessment in their regional hospitals first concluded the psychological examination (SPP-3 and then filled-in two questionnaires: The Family Environment Questionnaire (Zupančič, Podlesek, & Kavčič, 2004 and The Home Literacy Environment Questionnaire (Marjanovič Umek, Podlesek, & Fekonja, 2005. The results showed that quality of family environment does effect the child's adaptive capabilities and is associated with parental level of education. Of special importance for the child's socialization is the parents' ability to use effective control (to have consistent and clear demands. Hypothesis that the level of parental education affects the child's adaptation capabilities was not confirmed. Perhaps the parents' relations with the child are of greater importance, and these are probably not related to parents' education. The results show that child's adaptation capabilities are associated with parenting methods, so preventive psychological counselling may also be used to help parents choose more effective methods in order to allow the child to develop effective adaptive behaviour.

A Summary of Actinide Enrichment Technologies and Capability Gaps

Energy Technology Data Exchange (ETDEWEB)

Patton, Bradley D. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Robinson, Sharon M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-01-01

The evaluation performed in this study indicates that a new program is needed to efficiently provide a national actinide radioisotope enrichment capability to produce milligram-to-gram quantities of unique materials for user communities. This program should leverage past actinide enrichment, the recent advances in stable isotope enrichment, and assessments of the future requirements to cost effectively develop this capability while establishing an experience base for a new generation of researchers in this vital area. Preliminary evaluations indicate that an electromagnetic isotope separation (EMIS) device would have the capability to meet the future needs of the user community for enriched actinides. The EMIS technology could be potentially coupled with other enrichment technologies, such as irradiation, as pre-enrichment and/or post-enrichment systems to increase the throughput, reduce losses of material, and/or reduce operational costs of the base EMIS system. Past actinide enrichment experience and advances in the EMIS technology applied in stable isotope separations should be leveraged with this new evaluation information to assist in the establishment of a domestic actinide radioisotope enrichment capability.

Leak detection capability in CANDU reactors

Energy Technology Data Exchange (ETDEWEB)

Azer, N.; Barber, D.H.; Boucher, P.J. [and others

1997-04-01

This paper addresses the moisture leak detection capability of Ontario Hydro CANDU reactors which has been demonstrated by performing tests on the reactor. The tests confirmed the response of the annulus gas system (AGS) to the presence of moisture injected to simulate a pressure tube leak and also confirmed the dew point response assumed in leak before break assessments. The tests were performed on Bruce A Unit 4 by injecting known and controlled rates of heavy water vapor. To avoid condensation during test conditions, the amount of moisture which could be injected was small (2-3.5 g/hr). The test response demonstrated that the AGS is capable of detecting and annunciating small leaks. Thus confidence is provided that it would alarm for a growing pressure tube leak where the leak rate is expected to increase to kg/hr rapidly. The measured dew point response was close to that predicted by analysis.

Leak detection capability in CANDU reactors

International Nuclear Information System (INIS)

Azer, N.; Barber, D.H.; Boucher, P.J.

1997-01-01

This paper addresses the moisture leak detection capability of Ontario Hydro CANDU reactors which has been demonstrated by performing tests on the reactor. The tests confirmed the response of the annulus gas system (AGS) to the presence of moisture injected to simulate a pressure tube leak and also confirmed the dew point response assumed in leak before break assessments. The tests were performed on Bruce A Unit 4 by injecting known and controlled rates of heavy water vapor. To avoid condensation during test conditions, the amount of moisture which could be injected was small (2-3.5 g/hr). The test response demonstrated that the AGS is capable of detecting and annunciating small leaks. Thus confidence is provided that it would alarm for a growing pressure tube leak where the leak rate is expected to increase to kg/hr rapidly. The measured dew point response was close to that predicted by analysis

FMEF/experimental capabilities

International Nuclear Information System (INIS)

Burgess, C.A.; Dronen, V.R.

1981-01-01

The Fuels and Materials Examination Facility (FMEF), under construction at the Hanford site north of Richland, Washington, will be one of the most modern facilities offering irradiated fuels and materials examination capabilities and fuel fabrication development technologies. Scheduled for completion in 1984, the FMEF will provide examination capability for fuel assemblies, fuel pins and test pins irradiated in the FFTF. Various functions of the FMEF are described, with emphasis on experimental data-gathering capabilities in the facility's Nondestructive and Destructive examination cell complex

Assessing Graduate Sustainability Capability Post-Degree Completion: Why Is It Important and What Are the Challenges?

Science.gov (United States)

Sandri, Orana; Holdsworth, Sarah; Thomas, Ian

2018-01-01

Purpose: The purpose of this paper is to highlight both the need for measurement of graduate capabilities post-degree completion and the challenges posed by such a task. Higher education institutions provide an important site of learning that can equip future professionals with capabilities to manage and respond to complex sustainability…

Auto-Suggest Capability via Machine Learning in SMART NAS, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — We build machine learning capabilities that enables the Shadow Mode Assessment using Realistic Technologies for the NAS (SMART NAS) system to synthesize, optimize,...

A Comparative Assessment of the Navy’s Future Naval Capabilities (FNC) Process and Joint Staff Capability Gap Assessment Process as Related to Pacific Commands (PACOM) Integrated Priority List Submission

Science.gov (United States)

2013-04-01

based on personal interviews with Kit Carlan and Ken Bruner of PACOM, and PowerPoint slides dated March 23, 2011, and prepared by Kit Carlan. 8 The...Integration Branch, Joint Capability Division, J-8, Joint Staff; Mr. Ken Bruner , Science and Technology Advisor, PACOM; Mr. Kit Carlan, Future

ADVANCED SIMULATION CAPABILITY FOR ENVIRONMENTAL MANAGEMENT- CURRENT STATUS AND PHASE II DEMONSTRATION RESULTS

Energy Technology Data Exchange (ETDEWEB)

Seitz, R.

2013-02-26

The U.S. Department of Energy (USDOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Toolsets and High-Performance Computing (HPC) Multiprocess Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, toolsets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial toolsets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Force Structure: Capabilities and Cost of Army Modular Force Remain Uncertain

National Research Council Canada - National Science Library

2006-01-01

.... In short, because of uncertainties in cost, equipment, and personnel plans and the absence of a comprehensive approach for assessing modularity results, we do not believe decision makers have sufficient information to assess the capabilities, costs, and risks posed by the transformation to a modular force. I will now turn to our four main issues.

Capability maturity models for offshore organisational management.

Science.gov (United States)

Strutt, J E; Sharp, J V; Terry, E; Miles, R

2006-12-01

The goal setting regime imposed by the UK safety regulator has important implications for an organisation's ability to manage health and safety related risks. Existing approaches to safety assurance based on risk analysis and formal safety assessments are increasingly considered unlikely to create the step change improvement in safety to which the offshore industry aspires and alternative approaches are being considered. One approach, which addresses the important issue of organisational behaviour and which can be applied at a very early stage of design, is the capability maturity model (CMM). The paper describes the development of a design safety capability maturity model, outlining the key processes considered necessary to safety achievement, definition of maturity levels and scoring methods. The paper discusses how CMM is related to regulatory mechanisms and risk based decision making together with the potential of CMM to environmental risk management.

Qualification and application of nuclear reactor accident analysis code with the capability of internal assessment of uncertainty

International Nuclear Information System (INIS)

Borges, Ronaldo Celem

2001-10-01

This thesis presents an independent qualification of the CIAU code ('Code with the capability of - Internal Assessment of Uncertainty') which is part of the internal uncertainty evaluation process with a thermal hydraulic system code on a realistic basis. This is done by combining the uncertainty methodology UMAE ('Uncertainty Methodology based on Accuracy Extrapolation') with the RELAP5/Mod3.2 code. This allows associating uncertainty band estimates with the results obtained by the realistic calculation of the code, meeting licensing requirements of safety analysis. The independent qualification is supported by simulations with RELAP5/Mod3.2 related to accident condition tests of LOBI experimental facility and to an event which has occurred in Angra 1 nuclear power plant, by comparison with measured results and by establishing uncertainty bands on safety parameter calculated time trends. These bands have indeed enveloped the measured trends. Results from this independent qualification of CIAU have allowed to ascertain the adequate application of a systematic realistic code procedure to analyse accidents with uncertainties incorporated in the results, although there is an evident need of extending the uncertainty data base. It has been verified that use of the code with this internal assessment of uncertainty is feasible in the design and license stages of a NPP. (author)

Security Process Capability Model Based on ISO/IEC 15504 Conformant Enterprise SPICE

Directory of Open Access Journals (Sweden)

Mitasiunas Antanas

2014-07-01

Full Text Available In the context of modern information systems, security has become one of the most critical quality attributes. The purpose of this paper is to address the problem of quality of information security. An approach to solve this problem is based on the main assumption that security is a process oriented activity. According to this approach, product quality can be achieved by means of process quality - process capability. Introduced in the paper, SPICE conformant information security process capability model is based on process capability modeling elaborated by world-wide software engineering community during the last 25 years, namely ISO/IEC 15504 that defines the capability dimension and the requirements for process definition and domain independent integrated model for enterprise-wide assessment and Enterprise SPICE improvement

INTEGRATION OF FACILITY MODELING CAPABILITIES FOR NUCLEAR NONPROLIFERATION ANALYSIS

Energy Technology Data Exchange (ETDEWEB)

Gorensek, M.; Hamm, L.; Garcia, H.; Burr, T.; Coles, G.; Edmunds, T.; Garrett, A.; Krebs, J.; Kress, R.; Lamberti, V.; Schoenwald, D.; Tzanos, C.; Ward, R.

2011-07-18

Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

Integration of facility modeling capabilities for nuclear nonproliferation analysis

International Nuclear Information System (INIS)

Garcia, Humberto; Burr, Tom; Coles, Garill A.; Edmunds, Thomas A.; Garrett, Alfred; Gorensek, Maximilian; Hamm, Luther; Krebs, John; Kress, Reid L.; Lamberti, Vincent; Schoenwald, David; Tzanos, Constantine P.; Ward, Richard C.

2012-01-01

Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

Integration Of Facility Modeling Capabilities For Nuclear Nonproliferation Analysis

International Nuclear Information System (INIS)

Gorensek, M.; Hamm, L.; Garcia, H.; Burr, T.; Coles, G.; Edmunds, T.; Garrett, A.; Krebs, J.; Kress, R.; Lamberti, V.; Schoenwald, D.; Tzanos, C.; Ward, R.

2011-01-01

Developing automated methods for data collection and analysis that can facilitate nuclear nonproliferation assessment is an important research area with significant consequences for the effective global deployment of nuclear energy. Facility modeling that can integrate and interpret observations collected from monitored facilities in order to ascertain their functional details will be a critical element of these methods. Although improvements are continually sought, existing facility modeling tools can characterize all aspects of reactor operations and the majority of nuclear fuel cycle processing steps, and include algorithms for data processing and interpretation. Assessing nonproliferation status is challenging because observations can come from many sources, including local and remote sensors that monitor facility operations, as well as open sources that provide specific business information about the monitored facilities, and can be of many different types. Although many current facility models are capable of analyzing large amounts of information, they have not been integrated in an analyst-friendly manner. This paper addresses some of these facility modeling capabilities and illustrates how they could be integrated and utilized for nonproliferation analysis. The inverse problem of inferring facility conditions based on collected observations is described, along with a proposed architecture and computer framework for utilizing facility modeling tools. After considering a representative sampling of key facility modeling capabilities, the proposed integration framework is illustrated with several examples.

Clinical capabilities of graduates of an outcomes-based integrated medical program

Directory of Open Access Journals (Sweden)

Scicluna Helen A

2012-06-01

Full Text Available Abstract Background The University of New South Wales (UNSW Faculty of Medicine replaced its old content-based curriculum with an innovative new 6-year undergraduate entry outcomes-based integrated program in 2004. This paper is an initial evaluation of the perceived and assessed clinical capabilities of recent graduates of the new outcomes-based integrated medical program compared to benchmarks from traditional content-based or process-based programs. Method Self-perceived capability in a range of clinical tasks and assessment of medical education as preparation for hospital practice were evaluated in recent graduates after 3 months working as junior doctors. Responses of the 2009 graduates of the UNSW’s new outcomes-based integrated medical education program were compared to those of the 2007 graduates of UNSW’s previous content-based program, to published data from other Australian medical schools, and to hospital-based supervisor evaluations of their clinical competence. Results Three months into internship, graduates from UNSW’s new outcomes-based integrated program rated themselves to have good clinical and procedural skills, with ratings that indicated significantly greater capability than graduates of the previous UNSW content-based program. New program graduates rated themselves significantly more prepared for hospital practice in the confidence (reflective practice, prevention (social aspects of health, interpersonal skills (communication, and collaboration (teamwork subscales than old program students, and significantly better or equivalent to published benchmarks of graduates from other Australian medical schools. Clinical supervisors rated new program graduates highly capable for teamwork, reflective practice and communication. Conclusions Medical students from an outcomes-based integrated program graduate with excellent self-rated and supervisor-evaluated capabilities in a range of clinically-relevant outcomes. The program

What am I capable? Self-Assessment of Basic Competences

Directory of Open Access Journals (Sweden)

Antonia Ramírez García

2014-10-01

Full Text Available The aims of this research are focus in evaluate linguistic communication and mathematics competences of students in sixth grade of primary education from their perception, and to develop a valid and reliable questionnaire in order to perform a self-assessment. The methodology has quantitative, descriptive and correlational character. In this research 1424 students from 46 schools in Cordova and its province participated. The results show that variables such as gender, age, number of siblings and type of center have influence for a better or worse self-assessment of students; but extracurricular activities undertaken by students and the increased weekly time devoted are those which cause a greater appreciation of each competence. On the other hand, a lower daily use of television, computer and games console allows that students make a self-assess more capeble to different aspects of both competences.

Capability assessment and challenges for quantum technology gravity sensors for near surface terrestrial geophysical surveying

Science.gov (United States)

Boddice, Daniel; Metje, Nicole; Tuckwell, George

2017-11-01

Geophysical surveying is widely used for the location of subsurface features. Current technology is limited in terms of its resolution (thus size of features it can detect) and penetration depth and a suitable technique is needed to bridge the gap between shallow near surface investigation using techniques such as EM conductivity mapping and GPR commonly used to map the upper 5 m below ground surface, and large features at greater depths detectable using conventional microgravity (> 5 m below ground surface). This will minimise the risks from unknown features buried in and conditions of the ground during civil engineering work. Quantum technology (QT) gravity sensors potentially offer a step-change in technology for locating features which lie outside of the currently detectable range in terms of size and depth, but that potential is currently unknown as field instruments have not been developed. To overcome this, a novel computer simulation was developed for a large range of different targets of interest. The simulation included realistic noise modelling of instrumental, environmental and location sources of noise which limit the accuracy of current microgravity measurements, in order to assess the potential capability of the new QT instruments in realistic situations and determine some of the likely limitations on their implementation. The results of the simulations for near surface features showed that the new technology is best employed in a gradiometer configuration as opposed to the traditional single sensor gravimeter used by current instruments due to the ability to suppress vibrational environmental noise effects due to common mode rejection between the sensors. A significant improvement in detection capability of 1.5-2 times was observed, putting targets such as mineshafts into the detectability zone which would be a major advantage for subsurface surveying. Thus this research, for the first time, has demonstrated clearly the benefits of QT gravity

Work program analysis - defining the capability/risk plan

International Nuclear Information System (INIS)

Hrinivich, W.A.

2004-01-01

Bruce Power has developed and implemented an analysis methodology (Work Program Analysis) to assess and address corporate business risk associated with work group capability. Work Program Analysis is proving to be an excellent tool for identifying and supporting key business decisions facing the line and senior management at Bruce Power. The following describes the methodology, its application and the results achieved. (author)

[Health-related scientific and technological capabilities and university-industry research collaboration].

Science.gov (United States)

Britto, Jorge; Vargas, Marco Antônio; Gadelha, Carlos Augusto Grabois; Costa, Laís Silveira

2012-12-01

To examine recent developments in health-related scientific capabilities, the impact of lines of incentives on reducing regional scientific imbalances, and university-industry research collaboration in Brazil. Data were obtained from the Conselho Nacional de Desenvolvimento Científico e Tecnológico (Brazilian National Council for Scientific and Technological Development) databases for the years 2000 to 2010. There were assessed indicators of resource mobilization, research network structuring, and knowledge transfer between science and industry initiatives. Based on the regional distribution map of health-related scientific and technological capabilities there were identified patterns of scientific capabilities and science-industry collaboration. There was relative spatial deconcentration of health research groups and more than 6% of them worked in six areas of knowledge areas: medicine, collective health, dentistry, veterinary medicine, ecology and physical education. Lines of incentives that were adopted from 2000 to 2009 contributed to reducing regional scientific imbalances and improving preexisting capabilities or, alternatively, encouraging spatial decentralization of these capabilities. Health-related scientific and technological capabilities remain highly spatially concentrated in Brazil and incentive policies have contributed to reduce to some extent these imbalances.

NNSA/NV Consequence Management Capabilities for Radiological Emergency Response

International Nuclear Information System (INIS)

Bowman, D. R.

2002-01-01

The U.S. Department of Energy's National Nuclear Security Administration Nevada Operations Office (NNSA/NV) provides an integrated Consequence Management (CM) response capability for the (NNSA) in the event of a radiological emergency. This encompasses planning, technical operations, and home team support. As the lead organization for CM planning and operations, NNSA/NV coordinates the response of the following assets during the planning and operational phases of a radiological accident or incident: (1) Predictive dispersion modeling through the Atmospheric Release Advisory Capability (ARAC) at Lawrence Livermore National Laboratory (LLNL) and the High Consequence Assessment Group at Sandia National Laboratories (SNL); (2) Regional radiological emergency assistance through the eight Radiological Assistance Program (RAP) regional response centers; (3) Medical advice and assistance through the Radiation Emergency Assistance Center/Training Site (REAC/TS) in Oak Ridge, Tennessee; (4) Aerial radiological mapping using the fixed-wing and rotor-wing aircraft of the Aerial Measuring System (AMS); (5) Consequence Management Planning Teams (CMPT) and Consequence Management Response Teams (CMRT) to provide CM field operations and command and control. Descriptions of the technical capabilities employed during planning and operations are given below for each of the elements comprising the integrated CM capability

Human error data collection as a precursor to the development of a human reliability assessment capability in air traffic management

International Nuclear Information System (INIS)

Kirwan, Barry; Gibson, W. Huw; Hickling, Brian

2008-01-01

Quantified risk and safety assessments are now required for safety cases for European air traffic management (ATM) services. Since ATM is highly human-dependent for its safety, this suggests a need for formal human reliability assessment (HRA), as carried out in other industries such as nuclear power. Since the fundamental aspect of HRA is human error data, in the form of human error probabilities (HEPs), it was decided to take a first step towards development of an ATM HRA approach by deriving some HEPs in an ATM context. This paper reports a study, which collected HEPs via analysing the results of a real-time simulation involving air traffic controllers (ATCOs) and pilots, with a focus on communication errors. This study did indeed derive HEPs that were found to be concordant with other known communication human error data. This is a first step, and shows promise for HRA in ATM, since HEPs have been derived which could be used in safety assessments, although these HEPs are for only one (albeit critical) aspect of ATCOs' tasks (communications). The paper discusses options and potential ways forward for the development of a full HRA capability in ATM

A study of the external cooling capability for the prevention of reactor vessel failure

Energy Technology Data Exchange (ETDEWEB)

Chang, S H; Baek, W P; Moon, S K; Yang, S H; Kim, S H [Korea Advanced Institute of Science Technology, Daejeon (Korea, Republic of)

1994-07-15

This study (a 3-year program) aims to perform a comprehensive assessment of the feasibility of external vessel flooding with respect to advanced pressurized water reactor plants to be built in Korea. During the first year, review of the relevant phenomena and preliminary assessment of the concept have been performed. Also performed is a review of heat transfer correlations for the computer program that will be developed for assessment of the cooling capability of external vessel flooding. Important phenomena that determine the cooling capability of external vessel flooding are (a) the initial transient before formation of molten corium pool, (b) natural convection of in-vessel molten corium pool, (c) radiative heat exchange between the molten corium pool and the upper vessel structures, (d) thermal hydraulics outside the vessel, (e) structural integrity consideration, and (f) long-term phenomena. The adoption of the concept should be decided by considering several factors such as (a) vessel submergence procedure, (b) cooling requirements, (c) vessel design features, (d) steam production, (e) instrumentation needs, and (f) an overall accident management strategy. The external vessel cooling concept looks to be promising. However, further study is required for a reliable decision making. Several correlations are available for the prediction of cooling capability of the present concept. However, it is difficult to define a sufficiently reliable set of correlations; sensitivity studies would be required in assessing the cooling capability with the computer program.

The use of dynamic capabilities to boost innovation in a Brazilian Chemical Company

Directory of Open Access Journals (Sweden)

Cristiane Froehlich

Full Text Available Abstract Dynamic capabilities seek to explain how competitive advantages can be built in rapidly changing environments. This study aims to assess how the application of dynamic capabilities can contribute to the expansion of innovation capabilities. Data was collected on ten semi-structured interviews with executives from a chemical company, and analyzed using qualitative content analysis. Results indicate that the application of dynamic capabilities contributes to the development of innovation capabilities through the consolidation of the first dynamic capability (sensing, which fosters innovation. Sensing can be considered an organizational capability, resulting from the integration between organizational strategies and the innovation practices of the organization as a whole. This study brings the following contributions the need to include a new microfoundation in the sensing capability, which in this study is called ‘processes to manage innovation on a strategic level' and the need to adapt another microfoundation related to the sensing capability, called ‘processes oriented toward collaboration with suppliers to complement and stimulate innovations within the company'. It is suggested that these processes should be reassessed in terms of their potential to generate and complement organizational innovation.

Transforming organizational capabilities in strategizing

DEFF Research Database (Denmark)

Jørgensen, Claus; Friis, Ole Uhrskov; Koch, Christian

2014-01-01

Offshored and networked enterprises are becoming an important if not leading organizational form and this development seriously challenges their organizational capabilities. More specifically, over the last years, SMEs have commenced entering these kinds of arrangements. As the organizational...... capabilities of SMEs are limited at the outset, even more emphasis is needed regarding the issues of developing relevant organizational capabilities. This paper aims at investigating how capabilities evolve during an offshoring process of more than 5 years in two Danish SMEs, i.e. not only short- but long......-term evolvements within the companies. We develop our framework of understanding organizational capabilities drawing on dynamic capability, relational capability and strategy as practice concepts, appreciating the performative aspects of developing new routines. Our two cases are taken from one author’s Ph...

A Comparative Assessment of the Navy’s Future Naval Capabilities (FNC) Process and Joint Staff Capability Gap Assessment Process as Related to Pacific Command’s Integrated Priority List Submission

Science.gov (United States)

2012-12-13

is based on personal interviews with Kit Carlan and Ken Bruner of PACOM, and PowerPoint slides dated March 23, 2011 that were prepared by Kit Carlan...Ken Bruner , Science and Technology Advisor, PACOM; Mr. Kit Carlan, Future Capabilities Analyst, J-82, PACOM for key information and helpful

Towards a capability approach to child growth: A theoretical framework.

Science.gov (United States)

Haisma, Hinke; Yousefzadeh, Sepideh; Boele Van Hensbroek, Pieter

2018-04-01

Child malnutrition is an important cause of under-5 mortality and morbidity around the globe. Despite the partial success of (inter)national efforts to reduce child mortality, under-5 mortality rates continue to be high. The multidimensional approaches of the Sustainable Development Goals may suggest new directions for rethinking strategies for reducing child mortality and malnutrition. We propose a theoretical framework for developing a "capability" approach to child growth. The current child growth monitoring practices are based on 2 assumptions: (a) that anthropometric and motor development measures are the appropriate indicators; and (b) that child growth can be assessed using a single universal standard that is applicable around the world. These practices may be further advanced by applying a capability approach to child growth, whereby growth is redefined as the achievement of certain capabilities (of society, parents, and children). This framework is similar to the multidimensional approach to societal development presented in the seminal work of Amartya Sen. To identify the dimensions of healthy child growth, we draw upon theories from the social sciences and evolutionary biology. Conceptually, we consider growth as a plural space and propose assessing growth by means of a child growth matrix in which the context is embedded in the assessment. This approach will better address the diversities and the inequalities in child growth. Such a multidimensional measure will have implications for interventions and policy, including prevention and counselling, and could have an impact on child malnutrition and mortality. © 2017 The Authors. Maternal and Child Nutrition Published by John Wiley & Sons, Ltd.

Well-being, life satisfaction and capabilities of flood disaster victims

International Nuclear Information System (INIS)

Van Ootegem, Luc; Verhofstadt, Elsy

2016-01-01

The individual well-being of flood disaster victims is examined making use of two concepts: life satisfaction and perceived capabilities in life. These concepts are compared in two samples: a representative sample of Flemish respondents and a specific sample of people that have been the victim of a pluvial flood. Well-being as life satisfaction is found not to be related to past or expected future flooding, whereas well-being as capabilities in life is negatively related to both past and expected future flooding. - Highlights: • Well-being as life satisfaction is not related to past or expected future flooding. • Well-being as capabilities in life is negatively related to flooding. • A disaster can scare people for the future because of the scars that it provokes. • Assess the impact of a disaster not only by monetary damage and life satisfaction.

Well-being, life satisfaction and capabilities of flood disaster victims

Energy Technology Data Exchange (ETDEWEB)

Van Ootegem, Luc, E-mail: Luc.VanOotegem@UGent.be [HIVA–University of Louvain (Belgium); SHERPPA–Ghent University (Belgium); Verhofstadt, Elsy [SHERPPA–Ghent University (Belgium)

2016-02-15

The individual well-being of flood disaster victims is examined making use of two concepts: life satisfaction and perceived capabilities in life. These concepts are compared in two samples: a representative sample of Flemish respondents and a specific sample of people that have been the victim of a pluvial flood. Well-being as life satisfaction is found not to be related to past or expected future flooding, whereas well-being as capabilities in life is negatively related to both past and expected future flooding. - Highlights: • Well-being as life satisfaction is not related to past or expected future flooding. • Well-being as capabilities in life is negatively related to flooding. • A disaster can scare people for the future because of the scars that it provokes. • Assess the impact of a disaster not only by monetary damage and life satisfaction.

Extension of station blackout coping capability and implications on nuclear safety

Energy Technology Data Exchange (ETDEWEB)

Volkanovski, Andrija, E-mail: andrija.volkanovski@ijs.si [Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Prošek, Andrej [Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia)

2013-02-15

Highlights: ► Modifications enhancing station blackout coping capability are analyzed. ► Analysis is done with deterministic and probabilistic safety analysis methods. ► The core heat up is delayed for at least the extension time interval. ► Auxiliary feedwater system delays core heat up even in presence of pumps seal leakage. ► Extension of station blackout coping capability decreases core damage frequency. -- Abstract: The safety of the nuclear power plant depends on the availability of the continuous and reliable sources of electrical energy during all modes of operation of the plant. The station blackout corresponds to a total loss of all alternate current (AC) power as a result of complete failure of both offsite and on-site AC power sources. The electricity for the essential systems during station blackout is provided from the batteries installed in the nuclear power plant. The results of the probabilistic safety assessment show that station blackout is one of the main and frequently the dominant contributor to the core damage frequency. The accident in Fukushima Daiichi nuclear power plants demonstrates the vulnerability of the currently operating nuclear power plants during the extended station blackout events. The objective of this paper is, considering the identified importance of the station blackout initiating event, to assess the implications of the strengthening of the SBO mitigation capability on safety of the NPP. The assessment is done with state-of-art deterministic and probabilistic methods and tolls with application on reference models of nuclear power plants. The U.S. NRC Station Blackout Rule describes procedure for the assessment of the size and capacity of the batteries in the nuclear power plant. The description of the procedure with the application on the reference plant and identified deficiencies in the procedure is presented. The safety analysis is done on reference model of the nuclear power plant. Obtained results show large

Extension of station blackout coping capability and implications on nuclear safety

International Nuclear Information System (INIS)

Volkanovski, Andrija; Prošek, Andrej

2013-01-01

Highlights: ► Modifications enhancing station blackout coping capability are analyzed. ► Analysis is done with deterministic and probabilistic safety analysis methods. ► The core heat up is delayed for at least the extension time interval. ► Auxiliary feedwater system delays core heat up even in presence of pumps seal leakage. ► Extension of station blackout coping capability decreases core damage frequency. -- Abstract: The safety of the nuclear power plant depends on the availability of the continuous and reliable sources of electrical energy during all modes of operation of the plant. The station blackout corresponds to a total loss of all alternate current (AC) power as a result of complete failure of both offsite and on-site AC power sources. The electricity for the essential systems during station blackout is provided from the batteries installed in the nuclear power plant. The results of the probabilistic safety assessment show that station blackout is one of the main and frequently the dominant contributor to the core damage frequency. The accident in Fukushima Daiichi nuclear power plants demonstrates the vulnerability of the currently operating nuclear power plants during the extended station blackout events. The objective of this paper is, considering the identified importance of the station blackout initiating event, to assess the implications of the strengthening of the SBO mitigation capability on safety of the NPP. The assessment is done with state-of-art deterministic and probabilistic methods and tolls with application on reference models of nuclear power plants. The U.S. NRC Station Blackout Rule describes procedure for the assessment of the size and capacity of the batteries in the nuclear power plant. The description of the procedure with the application on the reference plant and identified deficiencies in the procedure is presented. The safety analysis is done on reference model of the nuclear power plant. Obtained results show large

Advanced Simulation Capability for Environmental Management - Current Status and Phase II Demonstration Results - 13161

Energy Technology Data Exchange (ETDEWEB)

Seitz, Roger R.; Flach, Greg [Savannah River National Laboratory, Savannah River Site, Bldg 773-43A, Aiken, SC 29808 (United States); Freshley, Mark D.; Freedman, Vicky; Gorton, Ian [Pacific Northwest National Laboratory, MSIN K9-33, P.O. Box 999, Richland, WA 99352 (United States); Dixon, Paul; Moulton, J. David [Los Alamos National Laboratory, MS B284, P.O. Box 1663, Los Alamos, NM 87544 (United States); Hubbard, Susan S.; Faybishenko, Boris; Steefel, Carl I.; Finsterle, Stefan [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 50B-4230, Berkeley, CA 94720 (United States); Marble, Justin [Department of Energy, 19901 Germantown Road, Germantown, MD 20874-1290 (United States)

2013-07-01

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) Multi-process Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial tool-sets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Advanced Simulation Capability for Environmental Management - Current Status and Phase II Demonstration Results - 13161

International Nuclear Information System (INIS)

Seitz, Roger R.; Flach, Greg; Freshley, Mark D.; Freedman, Vicky; Gorton, Ian; Dixon, Paul; Moulton, J. David; Hubbard, Susan S.; Faybishenko, Boris; Steefel, Carl I.; Finsterle, Stefan; Marble, Justin

2013-01-01

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) Multi-process Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial tool-sets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Experimental study of a single fuel jet in conditions of highly preheated air combustion

Energy Technology Data Exchange (ETDEWEB)

Lille, Simon; Blasiak, W. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Metallurgy

2000-04-01

Highly Preheated Air Combustion (HPAC) is a technique to reduce consumption of fuel and decrease NO{sub x} formation in furnaces. The main change that occur in the furnace chamber is that the flow pattern of flue gases changes dramatically resulting in a more uniform heat transfer. The usefulness of regenerative combustion is very clear, but the advantages have so far been accompanied by high levels of pollutants, such as NO{sub x}. The combination of the regeneration technique and internal flue gas recirculation, thus decreasing NO{sub x} and keeping the other advantages, has made HPAC a very attractive combustion technology with application to heat treatment reheating and melting processes. This work gives an introduction to regenerative combustion with diluted air, including theory on flame stabilization. Furthermore, a description of a new test furnace is given with results from a parametric study and from tests using schlieren color visualization, direct photography, and laser Doppler anemometry. In the parametric study NO{sub x}-emission, CO-emission, lift-off, fluctuations, and some flame characteristics are related to nozzle diameter, oxygen concentration, and preheat temperature. For the schlieren technique and direct photography, both still and high-speed cameras were used.

Savannah River release: test of the new ARAC capability

International Nuclear Information System (INIS)

Dickerson, M.H.

1977-01-01

Working jointly from opposite sides of the nation Lawrence Livermore Laboratory (LLL) and the Savannah River Laboratory (SRL) quickly assessed the consequences of an early-morning tritium release in May 1974 from the Savannah River Plant, in South Carolina. Measurements confirmed the accuracy of the LLL predictions. Due to the small quantity involved and to the release location (well within the plant confines), the release was not dangerous to the public. The emergency provided a dramatic test of procedures and capabilities of the new Atmospheric Release Advisory Capability (ARAC) center at Livermore, which was not yet operational, demonstrating the capacity for quick response, and the feasibility of real-time data acquisition and transmittal across the continent

A business analytics capability framework

Directory of Open Access Journals (Sweden)

Ranko Cosic

2015-09-01

Full Text Available Business analytics (BA capabilities can potentially provide value and lead to better organisational performance. This paper develops a holistic, theoretically-grounded and practically relevant business analytics capability framework (BACF that specifies, defines and ranks the capabilities that constitute an organisational BA initiative. The BACF was developed in two phases. First, an a priori conceptual framework was developed based on the Resource-Based View theory of the firm and a thematic content analysis of the BA literature. Second, the conceptual framework was further developed and refined using a three round Delphi study involving 16 BA experts. Changes from the Delphi study resulted in a refined and confirmed framework including detailed capability definitions, together with a ranking of the capabilities based on importance. The BACF will help academic researchers and industry practitioners to better understand the capabilities that constitute an organisational BA initiative and their relative importance. In future work, the capabilities in the BACF will be operationalised to measure their as-is status, thus enabling organisations to identify key areas of strength and weakness and prioritise future capability improvement efforts.

Sensor Alerting Capability

Science.gov (United States)

Henriksson, Jakob; Bermudez, Luis; Satapathy, Goutam

2013-04-01

There is a large amount of sensor data generated today by various sensors, from in-situ buoys to mobile underwater gliders. Providing sensor data to the users through standardized services, language and data model is the promise of OGC's Sensor Web Enablement (SWE) initiative. As the amount of data grows it is becoming difficult for data providers, planners and managers to ensure reliability of data and services and to monitor critical data changes. Intelligent Automation Inc. (IAI) is developing a net-centric alerting capability to address these issues. The capability is built on Sensor Observation Services (SOSs), which is used to collect and monitor sensor data. The alerts can be configured at the service level and at the sensor data level. For example it can alert for irregular data delivery events or a geo-temporal statistic of sensor data crossing a preset threshold. The capability provides multiple delivery mechanisms and protocols, including traditional techniques such as email and RSS. With this capability decision makers can monitor their assets and data streams, correct failures or be alerted about a coming phenomena.

A Hybrid Multi-Criteria Decision Model for Technological Innovation Capability Assessment: Research on Thai Automotive Parts Firms

Directory of Open Access Journals (Sweden)

Sumrit Detcharat

2013-01-01

Full Text Available The efficient appraisal of technological innovation capabilities (TICs of enterprises is an important factor to enhance competitiveness. This study aims to evaluate and rank TICs evaluation criteria in order to provide a practical insight of systematic analysis by gathering the qualified experts’ opinions combined with three methods of multi-criteria decision making approach. Firstly, Fuzzy Delphi method is used to screen TICs evaluation criteria from the recent published researches. Secondly, the Analytic Hierarchy Process is utilized to compute the relative important weights. Lastly, the VIKOR method is used to rank the enterprises based on TICs evaluation criteria. An empirical study is applied for Thai automotive parts firms to illustrate the proposed methods. This study found that the interaction between criteria is essential and influences TICs; furthermore, this ranking development of TICs assessment is also one of key management tools to simply facilitate and offer a new mindset for managements of other related industries.

Output capabilities of personal music players and assessment of preferred listening levels of test subjects: outlining recommendations for preventing music-induced hearing loss.

Science.gov (United States)

Breinbauer, Hayo A; Anabalón, Jose L; Gutierrez, Daniela; Cárcamo, Rodrigo; Olivares, Carla; Caro, Jorge

2012-11-01

Our goal was to assess the impact of personal music players, earphones, and music styles on output, the subject's preferred listening levels, and outline recommendations for the prevention of music-induced hearing loss. Experimental study. Personal music players' output capabilities and volunteers' preferred output levels were assessed in different settings. Based on current noise-induced hearing loss exposure limits, recommendations were outlined. On three different devices and earphone types and 10 music styles, free field equivalent sound pressure output levels were assessed by applying a microphone probe inside the auditory canal. Forty-five hearing-healthy volunteers were asked to select preferred listening levels in different background noise scenarios. Sound pressure output reached 126 dB. No difference was found between device types, whereas earbud and supra-aural earphones showed significantly lower outputs than in-ear earphones (P music style groups were identified with as much as 14.4 dB difference between them. In silence, 17.8% of volunteers spontaneously selected a listening level above 85 dB. With 90 dB background noise, 40% selected a level above 94 dB. Earphone attenuation capability was found to correlate significantly with preferred level reductions (r = 0.585, P < .001). In-ear and especially supra-aural earphones reduced preferred listening levels the most. Safe-use recommendations were outlined, whereas selecting the lowest volume setting comfortable remained the main suggestion. High background noise attenuating earphones may help in reducing comfortable listening levels and should be preferred. A risk table was elaborated, presenting time limits before reaching a risky exposure. Copyright © 2012 The American Laryngological, Rhinological, and Otological Society, Inc.

Short and longer duration effects of protective gloves on hand performance capabilities and subjective assessments in a screw-driving task.

Science.gov (United States)

Dianat, Iman; Haslegrave, Christine M; Stedmon, Alex W

2010-12-01

The study investigated short and longer duration effects of gloves on hand performance capabilities (muscle activity, dexterity, touch sensitivity, finger pinch and forearm torque strength) and subjective assessments of discomfort and ease of manipulation when performing a light assembly task. The independent variables were hand condition with four levels (wearing cotton, nylon or nitrile gloves as well as barehanded) and point of time within the 2 h duration of the task (with measurements taken at 0, 30, 60, 90 and 120 min). Participants worked with a screwdriver to fit two components together using screws. Wearing gloves significantly increased the muscle activity, pinch strength and discomfort but reduced the dexterity and touch sensitivity. There was also a significant effect of task time on the muscle activity, dexterity, forearm torque strength and touch sensitivity, which indicates that the duration of the task should be an important consideration in glove evaluation studies and in the selection of work gloves. STATEMENT OF RELEVANCE: It is important to evaluate the effects of gloves on hand performance capabilities in a working context so that job demands can be taken into account and the most appropriate type of glove be chosen for each task. This study gives recommendations regarding the evaluation and use of gloves for screw-driving tasks.

Resource-Based Capability on Development Knowledge Management Capabilities of Coastal Community

Science.gov (United States)

Teniwut, Roberto M. K.; Hasyim, Cawalinya L.; Teniwut, Wellem A.

2017-10-01

Building sustainable knowledge management capabilities in the coastal area might face a whole new challenge since there are many intangible factors involved from openness on new knowledge, access and ability to use the latest technology to the various local wisdom that still in place. The aimed of this study was to identify and analyze the resource-based condition of coastal community in this area to have an empirical condition of tangible and intangible infrastructure on developing knowledge management capability coastal community in Southeast Maluku, Indonesia. We used qualitative and quantitative analysis by depth interview and questionnaire for collecting the data with multiple linear regression as our analysis method. The result provided the information on current state of resource-based capability of a coastal community in this Southeast Maluku to build a sustainability model of knowledge management capabilities especially on utilization marine and fisheries resources. The implication of this study can provide an empirical information for government, NGO and research institution to dictate on how they conducted their policy and program on developing coastal community region.

United States Department of Energy radiological emergency response programme - a national capability

International Nuclear Information System (INIS)

Gordon-Hagerty, L.E.

1993-01-01

In order to respond to a radiological emergency, the United States Department of Energy (USDOE) maintains seven emergency response assets and capabilities in support of a radiological emergency of any proportion within the continental United States and abroad. The seven emergency response assets and capabilities include: Accident Response Group; Aerial Measuring Systems; Atmospheric Release Advisory Capability; Federal Radiological Monitoring and Assessment Center; Nuclear Emergency Search Team; Radiation Emergency Assistance Center/Training Site; and Radiological Assistance Program. Presently, USDOE maintains the most comprehensive national radiological emergency response assets in the United States, capable of dealing with any type of emergency involving nuclear materials. In all, the Department's assets are available to support any type of accident/incident involving radioactive materials in coordination with other United States Federal agencies, as well as state and local governments, as required. (author)

Campus Capability Plan

Energy Technology Data Exchange (ETDEWEB)

Adams, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Arsenlis, T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bailey, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bergman, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brase, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Brenner, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Camara, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Carlton, H. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Cheng, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chrzanowski, P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Colson, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); East, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Farrell, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ferranti, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gursahani, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hansen, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Helms, L. L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hernandez, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Jeffries, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Larson, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lu, K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); McNabb, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Mercer, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Skeate, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sueksdorf, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zucca, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Le, D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ancria, R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Scott, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Leininger, L. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gagliardi, F. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gash, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Bronson, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Chung, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hobson, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Meeker, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sanchez, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zagar, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Quivey, B. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sommer, S. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Atherton, J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-06-06

Lawrence Livermore National Laboratory Campus Capability Plan for 2018-2028. Lawrence Livermore National Laboratory (LLNL) is one of three national laboratories that are part of the National Nuclear Security Administration. LLNL provides critical expertise to strengthen U.S. security through development and application of world-class science and technology that: Ensures the safety, reliability, and performance of the U.S. nuclear weapons stockpile; Promotes international nuclear safety and nonproliferation; Reduces global danger from weapons of mass destruction; Supports U.S. leadership in science and technology. Essential to the execution and continued advancement of these mission areas are responsive infrastructure capabilities. This report showcases each LLNL capability area and describes the mission, science, and technology efforts enabled by LLNL infrastructure, as well as future infrastructure plans.

Experiences with the Capability Maturity Model in a research environment

NARCIS (Netherlands)

Velden, van der M.J.; Vreke, J.; Wal, van der B.; Symons, A.

1996-01-01

The project described here was aimed at evaluating the Capability Maturity Model (CMM) in the context of a research organization. Part of the evaluation was a standard CMM assessment. It was found that CMM could be applied to a research organization, although its five maturity levels were considered

Assessment of leak detection capability of Candu 6 annulus gas system using moisture injection tests

International Nuclear Information System (INIS)

Nho, Ki Man; Kim, Wang Bae

1998-01-01

The Candu 6 reactor assembly consists of an array of 380 pressure tubes, which are installed horizontally in a large cylindrical vessel, the Calandria, containing the low pressure heavy water moderator. The pressure tube is located inside calandria tube and the annulus between these tubes, which forms a closed loop with CO 2 gas recirculating, is called the Annulus Gas System (AGS). It is designed to give an alarm to the operator even for a small pressure tube leak by a very sensitive dew point meter so that he can take a preventive action for the pressure tbe rupture incident. To judge whether the operator action time is enough or not in the design of Wolsung 2, 3, and 4, the Leak Before Break (LBB) assessment is required for the analysis of the pressure tube failure accident. In order to provide the required data for the LBB assessment of Wolsung Units 2, 3, 4, a series of leak detection capability tests was performed by injecting controlled rates of heavy water vapour. The data of increased dew point and rates of rise were measured to determine the alarm set point for dew point rate of rise of Wolsung Unit 2. It was found that the response of the dew point depends on the moisture injection rate, CO 2 gas flow rate and the leak location. The test showed that Candu 6 AGS can detect the very small leaks less than few g/hr and dew point rate of rise alarm can be the most reliable alarm signal to warn the operator. Considering the present results, the first response time of dew point to the AGS CO 2 flow rate is approximated. (author)

Media Outlook 2016: A Survey of UK Media Trends and Firm Capabilities

OpenAIRE

Oliver, John James

2016-01-01

The aim of this survey is to understand the changing nature of the UK media environment, emerging trends and the management practices of media executives. This is the fourth year that the survey has run, and already we are seeing immense changes in the way media firms are adapting to a changing competitive landscape. This year, the focus of the survey has been on assessing media firm capabilities and the ability to adapt media strategy, business models and capabilities to new industry dynamic...

Maximizing Health or Sufficient Capability in Economic Evaluation? A Methodological Experiment of Treatment for Drug Addiction.

Science.gov (United States)

Goranitis, Ilias; Coast, Joanna; Day, Ed; Copello, Alex; Freemantle, Nick; Frew, Emma

2017-07-01

Conventional practice within the United Kingdom and beyond is to conduct economic evaluations with "health" as evaluative space and "health maximization" as the decision-making rule. However, there is increasing recognition that this evaluative framework may not always be appropriate, and this is particularly the case within public health and social care contexts. This article presents a methodological case study designed to explore the impact of changing the evaluative space within an economic evaluation from health to capability well-being and the decision-making rule from health maximization to the maximization of sufficient capability. Capability well-being is an evaluative space grounded on Amartya Sen's capability approach and assesses well-being based on individuals' ability to do and be the things they value in life. Sufficient capability is an egalitarian approach to decision making that aims to ensure everyone in society achieves a normatively sufficient level of capability well-being. The case study is treatment for drug addiction, and the cost-effectiveness of 2 psychological interventions relative to usual care is assessed using data from a pilot trial. Analyses are undertaken from a health care and a government perspective. For the purpose of the study, quality-adjusted life years (measured using the EQ-5D-5L) and years of full capability equivalent and years of sufficient capability equivalent (both measured using the ICECAP-A [ICEpop CAPability measure for Adults]) are estimated. The study concludes that different evaluative spaces and decision-making rules have the potential to offer opposing treatment recommendations. The implications for policy makers are discussed.

Application of capability indices and control charts in the analytical method control strategy.

Science.gov (United States)

Oliva, Alexis; Llabres Martinez, Matías

2017-08-01

In this study, we assessed the usefulness of control charts in combination with the process capability indices, C pm and C pk , in the control strategy of an analytical method. The traditional X-chart and moving range chart were used to monitor the analytical method over a 2-year period. The results confirmed that the analytical method is in-control and stable. Different criteria were used to establish the specifications limits (i.e. analyst requirements) for fixed method performance (i.e. method requirements). If the specification limits and control limits are equal in breadth, the method can be considered "capable" (C pm  = 1), but it does not satisfy the minimum method capability requirements proposed by Pearn and Shu (2003). Similar results were obtained using the C pk index. The method capability was also assessed as a function of method performance for fixed analyst requirements. The results indicate that the method does not meet the requirements of the analytical target approach. A real-example data of a SEC with light-scattering detection method was used as a model whereas previously published data were used to illustrate the applicability of the proposed approach. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Brandishing Cyberattack Capabilities

Science.gov (United States)

2013-01-01

Advertising cyberwar capabilities may be helpful. It may back up a deterrence strategy. It might dissuade other states from conventional mischief or...to enable the attack.5 Many of the instruments of the attack remain with the target system, nestled in its log files, or even in the malware itself...debat- able. Even if demonstrated, what worked yesterday may not work today. But difficult does not mean impossible. Advertising cyberwar capabilities

Improving the Agency's Software Acquisition Capability

Science.gov (United States)

Hankinson, Allen

2003-01-01

External development of software has oftc n led to unsatisfactory results and great frustration for the assurE 7ce community. Contracts frequently omit critical assuranc 4 processes or the right to oversee software development activitie: At a time when NASA depends more and more on software to in plement critical system functions, combination of three factors ex; cerbate this problem: I ) the ever-increasing trend to acquire rather than develop software in-house, 2) the trend toward performance based contracts, and 3) acquisition vehicles that only state softwar 2 requirements while leaving development standards and assur! ince methodologies up to the contractor. We propose to identify specific methods at d tools that NASA projects can use to mitigate the adverse el ects of the three problems. TWO broad classes of methoddt ols will be explored. The first will be those that provide NASA p ojects with insight and oversight into contractors' activities. The st cond will be those that help projects objectively assess, and thus i nprwe, their software acquisition capability. Of particular interest is the Software Engineering Institute's (SEI) Software Acqt isition Capability Maturity Model (SA-CMMO).

KSC Technical Capabilities Website

Science.gov (United States)

Nufer, Brian; Bursian, Henry; Brown, Laurette L.

2010-01-01

This document is the website pages that review the technical capabilities that the Kennedy Space Center (KSC) has for partnership opportunities. The purpose of this information is to make prospective customers aware of the capabilities and provide an opportunity to form relationships with the experts at KSC. The technical capabilities fall into these areas: (1) Ground Operations and Processing Services, (2) Design and Analysis Solutions, (3) Command and Control Systems / Services, (4) Materials and Processes, (5) Research and Technology Development and (6) Laboratories, Shops and Test Facilities.

Manufacturing capability as a technological development indicator in the pharmaceutical industry

Directory of Open Access Journals (Sweden)

John Jairo Gallo Castro

2010-01-01

Full Text Available The pharmaceutical industrial has five subsectors: medicines, cosmetics, phytotherapeutics, cleaning products and medical devices. The medicine subsector consists of organisations producing, importing and selling these products. Most studies about this industry have been guided by economic interests without assessing technological aspects of production. This article was aimed at proposing a methodology for assessing and describing the medicine sector according to its technological development by using the manufacturing capability concept. The main information was taken from the Colombian Medicaments and Food Surveillance Institute’s (Instituto Nacional de Vigilancia de Medicamentos y Alimentos - INVIMA databases related to pharmaceutical plant production in Bogotá, including material transformation facilities. This study led to three characteristics being identified for defining the pharmaceutical industry’s manufacturing capability: that related to the pharmacological group to which active pharmaceutical ingredients belong, that linked to specifications regarding medicines’ sterility and that related to the technology required for manufacturing each pharmaceutical product. An analysis of these features has thus been presented and some technologies have been identified which have not been transferred or assimilated by the organisations being studied. It was found that manufacturing capability should be considered as being an indicator of the degree of technological development in these subsectors in Colombia.

The atmospheric release advisory capability (ARAC): A federal emergency response capability

International Nuclear Information System (INIS)

Dickerson, M.H.; Sullivan, T.J.

1988-03-01

The Atmospheric Release Capability (ARAC) is a Department of Energy (DOE)-sponsored emergency-response service set up to provide real-time prediction of the dose levels and the extent of surface contamination resulting from a broad range of possible occurrences (accidents, spills, extortion threats involving nuclear material, reentry of nuclear-powered satellites, and atmospheric nuclear tests) that could involve the release of airborne radioactive material. During the past decade, ARAC has responded to more than 150 real-time situations, including exercises. The most notable responses include the Three Mile Island accident in Pennsylvania, the Titan II missile accident in Arkansas, the reentry of the USSR's COSMOS-954 into the atmosphere over Canada, the accidental release of uranium hexafluoride from the Sequoyah Facility accident in Oklahoma, and, most recently, the Chernobyl reactor accident in the Soviet Union. ARAC currently supports the emergency-preparedness plans at 50 Department of Defense (DOD) and DOE sites within the US and also responds to accidents that happen elsewhere. Our ARAC center serves as the focal point for data acquisition, data analysis and assessments during a response, using a computer-based communication network to acquire real-time weather data from the accident site and the surrounding region, as well as pertinent accident information. Its three-dimensional computer models for atmospheric dispersion, MATHEW and ADPIC, digest all this information and produce the predictions used in accident assessment. 9 refs., 6 figs., 1 tab

Organizational Economics of Capability and Heterogeneity

DEFF Research Database (Denmark)

Argyres, Nicholas S.; Felin, Teppo; Foss, Nicolai Juul

2012-01-01

For decades, the literatures on firm capabilities and organizational economics have been at odds with each other, specifically relative to explaining organizational boundaries and heterogeneity. We briefly trace the history of the relationship between the capabilities literature and organizational...... economics, and we point to the dominance of a “capabilities first” logic in this relationship. We argue that capabilities considerations are inherently intertwined with questions about organizational boundaries and internal organization, and we use this point to respond to the prevalent capabilities first...... logic. We offer an integrative research agenda that focuses first on the governance of capabilities and then on the capability of governance....

Metrology Measurement Capabilities

Energy Technology Data Exchange (ETDEWEB)

Dr. Glen E. Gronniger

2007-10-02

This document contains descriptions of Federal Manufacturing & Technologies (FM&T) Metrology capabilities, traceability flow charts, and the measurement uncertainty of each measurement capability. Metrology provides NIST traceable precision measurements or equipment calibration for a wide variety of parameters, ranges, and state-of-the-art uncertainties. Metrology laboratories conform to the requirements of the Department of Energy Development and Production Manual Chapter 13.2, ANSI/ISO/IEC ANSI/ISO/IEC 17025:2005, and ANSI/NCSL Z540-1. FM&T Metrology laboratories are accredited by NVLAP for the parameters, ranges, and uncertainties listed in the specific scope of accreditation under NVLAP Lab code 200108-0. See the Internet at http://ts.nist.gov/Standards/scopes/2001080.pdf. These parameters are summarized. The Honeywell Federal Manufacturing & Technologies (FM&T) Metrology Department has developed measurement technology and calibration capability in four major fields of measurement: (1) Mechanical; (2) Environmental, Gas, Liquid; (3) Electrical (DC, AC, RF/Microwave); and (4) Optical and Radiation. Metrology Engineering provides the expertise to develop measurement capabilities for virtually any type of measurement in the fields listed above. A strong audit function has been developed to provide a means to evaluate the calibration programs of our suppliers and internal calibration organizations. Evaluation includes measurement audits and technical surveys.

Capable design or designing capabilities? An exploration of service design as an emerging organizational capability in Telenor – Martinkenaite

Directory of Open Access Journals (Sweden)

Ieva Martinkenaite

2017-01-01

Full Text Available This empirical paper examines a process, starting with the managerial decision to make service design an organizational capability, and follows it as it unfolds over time within one organization. Service design has become an established business practice of how firms create new products and services to promote differentiation in an increasingly uncertain business landscape. Implicit in the literature on service design are assumptions about strategic implications of adopting the prescribed innovation methods and tools. However, little is known about how service design evolves into an organizational capability enabling firms to transform their existing businesses and sustain competitiveness. Through a longitudinal, exploratory case study of service design practices in one of the world’s largest telecommunications companies, we explicate mechanisms through which service design evolves into an organizational capability by exploring the research question: what are the mechanisms through which service design develops into an organizational capability? Our study reveals the effect of an initial introduction of service design tools, identification of boundaryspanning actors and co-alignment of dedicated resources between internal functions, as well as through co-creation with customers. Over time, these activities lead to the adoption of service design practices, and subsequently these practices spark incremental learning throughout the organization, alter managerial decisions and influence multiple paths for the development of new capabilities. Reporting on this process, we are able to describe how service design practices were disseminated and institutionalized within the organization we observed. This study thus contributes by informing how service design can evolve into an organizational capability, as well as by bridging the emerging literature on service design and design thinking with established strategy theory. Further research will have to

Space Logistics: Launch Capabilities

Science.gov (United States)

Furnas, Randall B.

1989-01-01

The current maximum launch capability for the United States are shown. The predicted Earth-to-orbit requirements for the United States are presented. Contrasting the two indicates the strong National need for a major increase in Earth-to-orbit lift capability. Approximate weights for planned payloads are shown. NASA is studying the following options to meet the need for a new heavy-lift capability by mid to late 1990's: (1) Shuttle-C for near term (include growth versions); and (2) the Advanced Lauching System (ALS) for the long term. The current baseline two-engine Shuttle-C has a 15 x 82 ft payload bay and an expected lift capability of 82,000 lb to Low Earth Orbit. Several options are being considered which have expanded diameter payload bays. A three-engine Shuttle-C with an expected lift of 145,000 lb to LEO is being evaluated as well. The Advanced Launch System (ALS) is a potential joint development between the Air Force and NASA. This program is focused toward long-term launch requirements, specifically beyond the year 2000. The basic approach is to develop a family of vehicles with the same high reliability as the Shuttle system, yet offering a much greater lift capability at a greatly reduced cost (per pound of payload). The ALS unmanned family of vehicles will provide a low end lift capability equivalent to Titan IV, and a high end lift capability greater than the Soviet Energia if requirements for such a high-end vehicle are defined.In conclusion, the planning of the next generation space telescope should not be constrained to the current launch vehicles. New vehicle designs will be driven by the needs of anticipated heavy users.

The Capability to Hold Property

NARCIS (Netherlands)

Claassen, Rutger

2015-01-01

This paper discusses the question of whether a capability theory of justice (such as that of Martha Nussbaum) should accept a basic “capability to hold property.” Answering this question is vital for bridging the gap between abstract capability theories of justice and their institutional

Conceptualizing innovation capabilities: A contingency perspective

Directory of Open Access Journals (Sweden)

Tor Helge Aas

2017-01-01

Full Text Available Empirical research has confirmed that a positive relationship exists between the implementation of innovation activities and the future performance of organizations. Firms utilize resources and capabilities to develop innovations in the form of new products, services or processes. Some firms prove to be better at reproducing innovation success than others, and the capacity to do so is referred to as innovation capability. However, the term innovation capability is ambiguously treated in extant literature. There are several different definitions of the concept and the distinction between innovation capabilities and other types of capabilities, such as dynamic capabilities, is neither explicitly stated, nor is the relationship between the concept and other resource- and capability-based concepts within strategy theory established. Although innovation is increasingly identified as crucial for a firm’s sustainable competitiveness in contemporary volatile and complex markets, the strategy-innovation link is underdeveloped in extant research. To overcome this challenge this paper raises the following research question: What type of innovation capabilities are required to innovate successfully? Due to the status of the extant research, we chose a conceptual research design to answer our research question and the paper contributes with a conceptual framework to discuss what innovation capabilities firms need to reproduce innovation success. Based on careful examination of current literature on innovation capability specifically, and the strategy-innovation link in general, we suggest that innovation capability must be viewed along two dimensions – innovation novelty and market characteristics. This framework enables the identification of four different contexts for innovation capabilities in a two-bytwo matrix. We discuss the types of innovation capabilities necessary within the four different contexts. This novel framework contributes to the

Iraqi Navy: Capability Requirements and Force Structure Recommendations for 2015 and Beyond

National Research Council Canada - National Science Library

Lawlor, Alison C; Thompson, Eric V

2008-01-01

.... The goal of this study is two-fold: to provide Iraqi and Coalition personnel with a common assessment of capability requirements and force structure recommendations for the Iraqi Navy, and to provide the Iraqi Navy leadership...

Developing Collaborative Product Development Capabilities

DEFF Research Database (Denmark)

Mahnke, Volker; Tran, Yen

2012-01-01

innovation strategies’. Our analyses suggest that developing such collaboration capabilities benefits from the search for complementary practices, the combination of learning styles, and the development of weak and strong ties. Results also underscore the crucial importance of co-evolution of multi......Collaborative product development capabilities support a company’s product innovation activities. In the context of the fast fashion sector, this paper examines the development of the product development capabilities (PDC) that align product development capabilities in a dual innovation context......, one, slow paced, where the firm is well established and the other, fast paced, which represents a new competitive arena in which the company competes. To understand the process associated with collaborative capability development, we studied three Scandinavian fashion companies pursuing ‘dual...

Core Capabilities and Technical Enhancement -- FY-98 Annual Report

Energy Technology Data Exchange (ETDEWEB)

Miller, David Lynn

1999-04-01

The Core Capability and Technical Enhancement (CC&TE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CC&TE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CC&TE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Core capabilities and technical enhancement, FY-98 annual report

Energy Technology Data Exchange (ETDEWEB)

Miller, D.L.

1999-04-01

The Core Capability and Technical Enhancement (CCTE) Program, a part of the Verification, Validation, and Engineering Assessment Program, was implemented to enhance and augment the technical capabilities of the Idaho National Engineering and Environmental Laboratory (INEEL). The purpose for strengthening the technical capabilities of the INEEL is to provide the technical base to serve effectively as the Environmental Management Laboratory for the Department of Energy's Office of Environmental Management (EM). An analysis of EM's science and technology needs as well as the technology investments currently being made by EM across the complex was used to formulate a portfolio of research activities designed to address EM's needs without overlapping work being done elsewhere. An additional purpose is to enhance and maintain the technical capabilities and research infrastructure at the INEEL. This is a progress report for fiscal year 1998 for the five CCTE research investment areas: (a) transport aspects of selective mass transport agents, (b) chemistry of environmental surfaces, (c) materials dynamics, (d) characterization science, and (e) computational simulation of mechanical and chemical systems. In addition to the five purely technical research areas, this report deals with the science and technology foundations element of the CCTE from the standpoint of program management and complex-wide issues. This report also provides details of ongoing and future work in all six areas.

Executive Summary of Ares V: Lunar Capabilities Concept Review Through Phase A-Cycle 3

Science.gov (United States)

Holladay, J. B.; Baggett, K. E.; Feldman, S. M.

2011-01-01

This Technical Memorandum (TM) was generated as an overall Ares V summary from the Lunar Capabilities Concept Review (LCCR) through Phase A-Cycle 3 (PA-C3) with the intent that it may be coupled with separately published appendices for a more detailed, integrated narrative. The Ares V has evolved from the initial point of departure (POD) 51.00.48 LCCR configuration to the current candidate POD, PA-C3D, and the family of vehicles concept that contains vehicles PA-C3A through H. The logical progression from concept to POD vehicles is summarized in this TM and captures the trade space and performance of each. The family-of-vehicles concept was assessed during PA-C3 and offered flexibility in the path forward with the ability to add options deemed appropriate. A description of each trade space is given in addition to a summary of each Ares V element. The Ares V contributions to a Mars campaign are also highlighted with the goal of introducing Ares V capabilities within the trade space. The assessment of the Ares V vehicle as it pertains to Mars missions remained locked to the architecture presented in Mars Design Reference Authorization 5.0 using the PA-C3D vehicle configuration to assess Mars transfer vehicle options, in-space EDS capabilities, docking adaptor and propellant transfer assessments, and lunar and Mars synergistic potential.

Assessing reactor physics codes capabilities to simulate fast reactors on the example of the BN-600 benchmark

Energy Technology Data Exchange (ETDEWEB)

Ivanov, Vladimir [Scientific and Engineering Centre for Nuclear and Radiation Safety (SES NRS), Moscow (Russian Federation); Bousquet, Jeremy [Gesellschaft fuer Anlagen- und Reaktorsicherheit (GRS) gGmbH, Garching (Germany)

2016-11-15

This work aims to assess the capabilities of reactor physics codes (initially validated for thermal reactors) to simulate fast sodium cooled reactors. The BFS-62-3A critical experiment from the BN-600 Hybrid Core Benchmark Analyses was chosen for the investigation. Monte-Carlo codes (KENO from SCALE and SERPENT 2.1.23) and the deterministic diffusion code DYN3D-MG are applied to calculate the neutronic parameters. It was found that the multiplication factor and reactivity effects calculated by KENO and SERPENT using the ENDF/B-VII.0 continuous energy library are in a good agreement with each other and with the measured benchmark values. Few-groups macroscopic cross sections, required for DYN3D-MG, were prepared in applying different methods implemented in SCALE and SERPENT. The DYN3D-MG results of a simplified benchmark show reasonable agreement with results from Monte-Carlo calculations and measured values. The former results are used to justify DYN3D-MG implementation for sodium cooled fast reactors coupled deterministic analysis.

Dynamic Capabilities and Performance

DEFF Research Database (Denmark)

Wilden, Ralf; Gudergan, Siegfried P.; Nielsen, Bo Bernhard

2013-01-01

are contingent on the competitive intensity faced by firms. Our findings demonstrate the performance effects of internal alignment between organizational structure and dynamic capabilities, as well as the external fit of dynamic capabilities with competitive intensity. We outline the advantages of PLS...

Nuclear and particle physics, astrophysics and cosmology (NPAC) capability review

Energy Technology Data Exchange (ETDEWEB)

Redondo, Antonio [Los Alamos National Laboratory

2010-01-01

The present document represents a summary self-assessment of the status of the Nuclear and Particle Physics, Astrophysics and Cosmology (NPAC) capability across Los Alamos National Laboratory (LANL). For the purpose of this review, we have divided the capability into four theme areas: Nuclear Physics, Particle Physics, Astrophysics and Cosmology, and Applied Physics. For each theme area we have given a general but brief description of the activities under the area, a list of the Laboratory divisions involved in the work, connections to the goals and mission of the Laboratory, a brief description of progress over the last three years, our opinion of the overall status of the theme area, and challenges and issues.

Marketing Capability in Strategy Research

DEFF Research Database (Denmark)

Ritter, Thomas; Distel, Andreas Philipp

Following the call for a demand-side perspective of strategic management (e.g., Priem et al., 2012), a firm’s marketing capability, i.e. its ability to interact with down-stream stakeholders, becomes a pivotal element in explaining a firm’s competitiveness. While marketing capability is recognized...... in the strategic management literature as an important driver of firm performance, our review of 86 articles reveals a lack of a generally accepted definition of marketing capability, a lack of a common conceptualization as well as differences in the measurement of marketing capability. In order to build a common...... ground for advancing marketing capability research and thus supporting the demand-side perspective in strategic management, we develop an integrative framework to explain the differences and propose a research agenda for developing the field....

COMPUTER SUPPORT SYSTEMS FOR ESTIMATING CHEMICAL TOXICITY: PRESENT CAPABILITIES AND FUTURE TRENDS

Science.gov (United States)

Computer Support Systems for Estimating Chemical Toxicity: Present Capabilities and Future Trends A wide variety of computer-based artificial intelligence (AI) and decision support systems exist currently to aid in the assessment of toxicity for environmental chemicals. T...

Imaging capabilities of germanium gamma cameras

International Nuclear Information System (INIS)

Steidley, J.W.

1977-01-01

Quantitative methods of analysis based on the use of a computer simulation were developed and used to investigate the imaging capabilities of germanium gamma cameras. The main advantage of the computer simulation is that the inherent unknowns of clinical imaging procedures are removed from the investigation. The effects of patient scattered radiation were incorporated using a mathematical LSF model which was empirically developed and experimentally verified. Image modifying effects of patient motion, spatial distortions, and count rate capabilities were also included in the model. Spatial domain and frequency domain modeling techniques were developed and used in the simulation as required. The imaging capabilities of gamma cameras were assessed using low contrast lesion source distributions. The results showed that an improvement in energy resolution from 10% to 2% offers significant clinical advantages in terms of improved contrast, increased detectability, and reduced patient dose. The improvements are of greatest significance for small lesions at low contrast. The results of the computer simulation were also used to compare a design of a hypothetical germanium gamma camera with a state-of-the-art scintillation camera. The computer model performed a parametric analysis of the interrelated effects of inherent and technological limitations of gamma camera imaging. In particular, the trade-off between collimator resolution and collimator efficiency for detection of a given low contrast lesion was directly addressed. This trade-off is an inherent limitation of both gamma cameras. The image degrading effects of patient motion, camera spatial distortions, and low count rate were shown to modify the improvements due to better energy resolution. Thus, based on this research, the continued development of germanium cameras to the point of clinical demonstration is recommended

The Impact of IT Capability on Employee Capability, Customer Value, Customer Satisfaction, and Business Performance

Science.gov (United States)

Chae, Ho-Chang

2009-01-01

This study empirically examines the impact of IT capability on firms' performance and evaluates whether firms' IT capabilities play a role in improving employee capability, customer value, customer satisfaction, and ultimately business performance. The results were based on comparing the business performance of the IT leader companies with that of…

Amartya Sen's Capability Approach and Education

Science.gov (United States)

Walker, Melanie

2005-01-01

The human capabilities approach developed by the economist Amartya Sen links development, quality of life and freedom. This article explores the key ideas in the capability approach of: capability, functioning, agency, human diversity and public participation in generating valued capabilities. It then considers how these ideas relate specifically…

Joint Assessment of ETRR-2 Research Reactor Operations Program, Capabilities, and Facilities

International Nuclear Information System (INIS)

Bissani, M; O'Kelly, D S

2006-01-01

A joint assessment meeting was conducted at the Egyptian Atomic Energy Agency (EAEA) followed by a tour of Egyptian Second Research Reactor (ETRR-2) on March 22 and 23, 2006. The purpose of the visit was to evaluate the capabilities of the new research reactor and its operations under Action Sheet 4 between the U.S. DOE and the EAEA, ''Research Reactor Operation'', and Action Sheet 6, ''Technical assistance in The Production of Radioisotopes''. Preliminary Recommendations of the joint assessment are as follows: (1) ETRR-2 utilization should be increased by encouraging frequent and sustained operations. This can be accomplished in part by (a) Improving the supply-chain management for fresh reactor fuel and alleviating the perception that the existing fuel inventory should be conserved due to unreliable fuel supply; and (b) Promulgating a policy for sample irradiation priority that encourages the use of the reactor and does not leave the decision of when to operate entirely at the discretion of reactor operations staff. (2) Each experimental facility in operation or built for a single purpose should be reevaluated to focus on those that most meet the goals of the EAEA strategic business plan. Temporary or long-term elimination of some experimental programs might be necessary to provide more focused utilization. There may be instances of emerging reactor applications for which no experimental facility is yet designed or envisioned. In some cases, an experimental facility may have a more beneficial use than the purpose for which it was originally designed. For example, (a) An effective Boron Neutron Capture Therapy (BNCT) program requires nearby high quality medical facilities. These facilities are not available and are unlikely to be constructed near the Inshas site. Further, the BNCT facility is not correctly designed for advanced research and therapy programs using epithermal neutrons. (b) The ETRR-2 is frequently operated to provide color-enhanced gemstones but is

Joint Assessment of ETRR-2 Research Reactor Operations Program, Capabilities, and Facilities

Energy Technology Data Exchange (ETDEWEB)

Bissani, M; O' Kelly, D S

2006-05-08

A joint assessment meeting was conducted at the Egyptian Atomic Energy Agency (EAEA) followed by a tour of Egyptian Second Research Reactor (ETRR-2) on March 22 and 23, 2006. The purpose of the visit was to evaluate the capabilities of the new research reactor and its operations under Action Sheet 4 between the U.S. DOE and the EAEA, ''Research Reactor Operation'', and Action Sheet 6, ''Technical assistance in The Production of Radioisotopes''. Preliminary Recommendations of the joint assessment are as follows: (1) ETRR-2 utilization should be increased by encouraging frequent and sustained operations. This can be accomplished in part by (a) Improving the supply-chain management for fresh reactor fuel and alleviating the perception that the existing fuel inventory should be conserved due to unreliable fuel supply; and (b) Promulgating a policy for sample irradiation priority that encourages the use of the reactor and does not leave the decision of when to operate entirely at the discretion of reactor operations staff. (2) Each experimental facility in operation or built for a single purpose should be reevaluated to focus on those that most meet the goals of the EAEA strategic business plan. Temporary or long-term elimination of some experimental programs might be necessary to provide more focused utilization. There may be instances of emerging reactor applications for which no experimental facility is yet designed or envisioned. In some cases, an experimental facility may have a more beneficial use than the purpose for which it was originally designed. For example, (a) An effective Boron Neutron Capture Therapy (BNCT) program requires nearby high quality medical facilities. These facilities are not available and are unlikely to be constructed near the Inshas site. Further, the BNCT facility is not correctly designed for advanced research and therapy programs using epithermal neutrons. (b) The ETRR-2 is frequently operated to

Capabilities for innovation

DEFF Research Database (Denmark)

Nielsen, Peter; Nielsen, Rene Nesgaard; Bamberger, Simon Grandjean

2012-01-01

is a survey that collected information from 601 firms belonging to the private urban sector in Denmark. The survey was carried out in late 2010. Keywords: dynamic capabilities/innovation/globalization/employee/employer cooperation/Nordic model Acknowledgment: The GOPA study was financed by grant 20080053113......Technological developments combined with increasing levels of competition related to the ongoing globalization imply that firms find themselves in dynamic, changing environments that call for dynamic capabilities. This challenges the internal human and organizational resources of firms in general...

Telematics Options and Capabilities

Energy Technology Data Exchange (ETDEWEB)

Hodge, Cabell [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-05

This presentation describes the data tracking and analytical capabilities of telematics devices. Federal fleet managers can use the systems to keep their drivers safe, maintain a fuel efficient fleet, ease their reporting burden, and save money. The presentation includes an example of how much these capabilities can save fleets.

Graphical Visualization of Human Exploration Capabilities

Science.gov (United States)

Rodgers, Erica M.; Williams-Byrd, Julie; Arney, Dale C.; Simon, Matthew A.; Williams, Phillip A.; Barsoum, Christopher; Cowan, Tyler; Larman, Kevin T.; Hay, Jason; Burg, Alex

2016-01-01

NASA's pioneering space strategy will require advanced capabilities to expand the boundaries of human exploration on the Journey to Mars (J2M). The Evolvable Mars Campaign (EMC) architecture serves as a framework to identify critical capabilities that need to be developed and tested in order to enable a range of human exploration destinations and missions. Agency-wide System Maturation Teams (SMT) are responsible for the maturation of these critical exploration capabilities and help formulate, guide and resolve performance gaps associated with the EMC-identified capabilities. Systems Capability Organization Reporting Engine boards (SCOREboards) were developed to integrate the SMT data sets into cohesive human exploration capability stories that can be used to promote dialog and communicate NASA's exploration investments. Each SCOREboard provides a graphical visualization of SMT capability development needs that enable exploration missions, and presents a comprehensive overview of data that outlines a roadmap of system maturation needs critical for the J2M. SCOREboards are generated by a computer program that extracts data from a main repository, sorts the data based on a tiered data reduction structure, and then plots the data according to specified user inputs. The ability to sort and plot varying data categories provides the flexibility to present specific SCOREboard capability roadmaps based on customer requests. This paper presents the development of the SCOREboard computer program and shows multiple complementary, yet different datasets through a unified format designed to facilitate comparison between datasets. Example SCOREboard capability roadmaps are presented followed by a discussion of how the roadmaps are used to: 1) communicate capability developments and readiness of systems for future missions, and 2) influence the definition of NASA's human exploration investment portfolio through capability-driven processes. The paper concludes with a description

Assessing the weather monitoring capabilities of cellular microwave link networks

Science.gov (United States)

Fencl, Martin; Vrzba, Miroslav; Rieckermann, Jörg; Bareš, Vojtěch

2016-04-01

Using of microwave links for rainfall monitoring was suggested already by (Atlas and Ulbrich, 1977). However, this technique attracted broader attention of scientific community only in the recent decade, with the extensive growth of cellular microwave link (CML) networks, which form the backbone of today's cellular telecommunication infrastructure. Several studies have already shown that CMLs can be conveniently used as weather sensors and have potential to provide near-ground path-integrated observations of rainfall but also humidity or fog. However, although research is still focusing on algorithms to improve the weather sensing capabilities (Fencl et al., 2015), it is not clear how to convince cellular operators to provide the power levels of their network. One step in this direction is to show in which regions or municipalities the networks are sufficiently dense to provide/develop good services. In this contribution we suggest a standardized approach to evaluate CML networks in terms of rainfall observation and to identify suitable regions for CML rainfall monitoring. We estimate precision of single CML based on its sensitivity to rainfall, i.e. as a function of frequency, polarization and path length. Capability of a network to capture rainfall spatial patterns is estimated from the CML coverage and path lengths considering that single CML provides path-integrated rain rates. We also search for suitable predictors for regions where no network topologies are available. We test our approach on several European networks and discuss the results. Our results show that CMLs are very dense in urban areas (> 1 CML/km2), but less in rural areas (online tool. In summary, our results demonstrate that CML represent promising environmental observation network, suitable especially for urban rainfall monitoring. The developed approach integrated into an open source online tool can be conveniently used e.g. by local operators or authorities to evaluate the suitability of

The Capability Approach

OpenAIRE

Robeyns, Ingrid

2011-01-01

textabstract In its most general description, the capability approach is a flexible and multi-purpose normative framework, rather than a precise theory of well-being, freedom or justice. At its core are two normative claims: first, the claim that the freedom to achieve well-being is of primary moral importance, and second, that freedom to achieve well-being is to be understood in terms of people’s capabilities, that is, their real opportunities to do and be what they have reason to value. Thi...

Sandia QIS Capabilities.

Energy Technology Data Exchange (ETDEWEB)

Muller, Richard P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-07-01

Sandia National Laboratories has developed a broad set of capabilities in quantum information science (QIS), including elements of quantum computing, quantum communications, and quantum sensing. The Sandia QIS program is built atop unique DOE investments at the laboratories, including the MESA microelectronics fabrication facility, the Center for Integrated Nanotechnologies (CINT) facilities (joint with LANL), the Ion Beam Laboratory, and ASC High Performance Computing (HPC) facilities. Sandia has invested $75 M of LDRD funding over 12 years to develop unique, differentiating capabilities that leverage these DOE infrastructure investments.

A Study on the Impact of Marketing Capability, Operations Capability, Environmental Capability and Diversification Strategy on the Performance of Hotel Industry in the UK

OpenAIRE

ZHANG, YUBO

2009-01-01

Hotel industry has been an increasingly significant service industry across the whole world. The performance measurement method is crucial for hotels’ operations. This study examines the impacts of marketing capability, operations capability, environmental capability and diversification strategy on the business performance of hotel industry in the UK. Based on the financial archival data in the database and information obtained in the firm websites from 2004 to 2007, the investigation is carr...

Stochastic and simulation models of maritime intercept operations capabilities

OpenAIRE

Sato, Hiroyuki

2005-01-01

The research formulates and exercises stochastic and simulation models to assess the Maritime Intercept Operations (MIO) capabilities. The models focus on the surveillance operations of the Maritime Patrol Aircraft (MPA). The analysis using the models estimates the probability with which a terrorist vessel (Red) is detected, correctly classified, and escorted for intensive investigation and neutralization before it leaves an area of interest (AOI). The difficulty of obtaining adequate int...

National Research Council Dialogue to Assess Progress on NASA's Systems Engineering Cost/Risk Analysis Capability Roadmap Development: General Background and Introduction

Science.gov (United States)

Regenie, Victoria

2005-01-01

Contents include the following: General Background and Introduction of Capability. Roadmaps for Systems Engineering Cost/Risk Analysis. Agency Objectives. Strategic Planning Transformation. Review Capability Roadmaps and Schedule. Review Purpose of NRC Review. Capability Roadmap Development (Progress to Date).

Strength capability while kneeling.

Science.gov (United States)

Haslegrave, C M; Tracy, M F; Corlett, E N

1997-12-01

Work sometimes has to be carried out kneeling, particularly where jobs are performed in confined spaces as is common for miners, aircraft baggage handlers and maintenance workers. In order to assess the risks in performing forceful tasks under such conditions, data is needed on strength capabilities of kneeling subjects. A study was undertaken to measure isometric strength in single-handed exertions for male subjects and to investigate the effects on this of task layout factors (direction of force exertion, reach distance, height of the workpiece and orientation relative to the subject's sagittal plane). The data has been tabulated to show the degree to which strength may be reduced in different situations and analysis of the task factors showed their influence to be complex with direction of exertion and reach distance having the greatest effect. The results also suggest that exertions are weaker when subjects are kneeling on two knees than when kneeling on one knee, although this needs to be confirmed by direct experimental comparison.

Does organizational agility affect organizational learning capability? Evidence from commercial banking

Directory of Open Access Journals (Sweden)

Zaina Mustafa Mahmoud Hamad

2017-08-01

Full Text Available Both organizational agility and learning capability are prerequisites for organizational survival and success. This study explores the contribution of agility practices to organizational learning capabilities at the commercial banks in Jordan. To examine the proposed model, a sample of 158 employees within top and middle managements was used. Structural Equation Modeling was conducted for assessing validity and reliability of measurement instrument, evaluating model fit, and testing hypotheses. This study recognizes agility as a key element of learning facilitators. Findings affirm the strategic value of agility and conclude that administrators working within ag-ile organizations would be able to acquire conditions that foster learning.

Capability and Interface Assessment of Gaming Technologies for Future Multi-Unmanned Air Vehicle Systems

Science.gov (United States)

2011-08-01

Playing Games ( MMORPG ), which necessitate the management of multiple independent entities with sophisticated capabilities; and finally, arcade-style... MMORPG , SA 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT SAR 18. NUMBER OF PAGES 34 19a. NAME OF RESPONSIBLE...tested platform for simultaneous control of multiple entities. Similarly, the popularity of Massively Multiplayer Online Role Playing Games ( MMORPG

Collaborative environments for capability-based planning

Science.gov (United States)

McQuay, William K.

2005-05-01

Distributed collaboration is an emerging technology for the 21st century that will significantly change how business is conducted in the defense and commercial sectors. Collaboration involves two or more geographically dispersed entities working together to create a "product" by sharing and exchanging data, information, and knowledge. A product is defined broadly to include, for example, writing a report, creating software, designing hardware, or implementing robust systems engineering and capability planning processes in an organization. Collaborative environments provide the framework and integrate models, simulations, domain specific tools, and virtual test beds to facilitate collaboration between the multiple disciplines needed in the enterprise. The Air Force Research Laboratory (AFRL) is conducting a leading edge program in developing distributed collaborative technologies targeted to the Air Force's implementation of systems engineering for a simulation-aided acquisition and capability-based planning. The research is focusing on the open systems agent-based framework, product and process modeling, structural architecture, and the integration technologies - the glue to integrate the software components. In past four years, two live assessment events have been conducted to demonstrate the technology in support of research for the Air Force Agile Acquisition initiatives. The AFRL Collaborative Environment concept will foster a major cultural change in how the acquisition, training, and operational communities conduct business.

NGNP Data Management and Analysis System Analysis and Web Delivery Capabilities

Energy Technology Data Exchange (ETDEWEB)

Cynthia D. Gentillon

2011-09-01

Projects for the Very High Temperature Reactor (VHTR) Technology Development Office provide data in support of Nuclear Regulatory Commission licensing of the very high temperature reactor. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high-temperature and high-fluence environments. The NGNP Data Management and Analysis System (NDMAS) at the Idaho National Laboratory has been established to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and for data analysis to identify useful relationships among the measured quantities. The capabilities are described from the perspective of NDMAS users, starting with those who just view experimental data and analytical results on the INL NDMAS web portal. Web display and delivery capabilities are described in detail. Also the current web pages that show Advanced Gas Reactor, Advanced Graphite Capsule, and High Temperature Materials test results are itemized. Capabilities available to NDMAS developers are more extensive, and are described using a second series of examples. Much of the data analysis efforts focus on understanding how thermocouple measurements relate to simulated temperatures and other experimental parameters. Statistical control charts and correlation monitoring provide an ongoing assessment of instrument accuracy. Data analysis capabilities are virtually unlimited for those who use the NDMAS web data download capabilities and the analysis software of their choice. Overall, the NDMAS provides convenient data analysis and web delivery capabilities for studying a very large and rapidly increasing database of well-documented, pedigreed data.

Developing an operational capabilities index of the emergency services sector.

Energy Technology Data Exchange (ETDEWEB)

Collins, M.J.; Eaton, L.K.; Shoemaker, Z.M.; Fisher, R.E.; Veselka, S.N.; Wallace, K.E.; Petit, F.D. (Decision and Information Sciences)

2012-02-20

capabilities of a jurisdiction to protect itself from, mitigate, respond to, and recover from a potential incident. On the basis of this metric, an interactive tool - the ESSCI Dashboard - can identify scenarios for enhancement that can be implemented, and it can identify the repercussions of these scenarios on the jurisdiction. It can assess the capabilities of law enforcement, fire fighting, search and rescue, emergency medical services, hazardous materials response, dispatch/911, and emergency management services in a given jurisdiction and it can help guide those who need to prioritize what limited resources should be used to improve these capabilities. Furthermore, this tool can be used to compare the level of capabilities of various jurisdictions that have similar socioeconomic characteristics. It can thus help DHS define how it can support risk reduction and community preparedness at a national level. This tool aligns directly with Presidential Policy Directive 8 by giving a jurisdiction a metric of its ESS's capabilities and by promoting an interactive approach for defining options to improve preparedness and to effectively respond to a disruptive event. It can be used in combination with other CI performance metrics developed at Argonne National Laboratory, such as the vulnerability index and the resilience index for assessing regional resilience.

Advanced Simulation Capability for Environmental Management (ASCEM) Phase II Demonstration

Energy Technology Data Exchange (ETDEWEB)

Freshley, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hubbard, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Flach, G. [Savannah River National Lab. (SRNL), Aiken, SC (United States); Freedman, V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Agarwal, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Andre, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bott, Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chen, X. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Davis, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Faybishenko, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gorton, I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Murray, C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moulton, D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meyer, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rockhold, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shoshani, A. [LBNL; Steefel, C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wainwright, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Waichler, S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2012-09-28

In 2009, the National Academies of Science (NAS) reviewed and validated the U.S. Department of Energy Office of Environmental Management (EM) Technology Program in its publication, Advice on the Department of Energy’s Cleanup Technology Roadmap: Gaps and Bridges. The NAS report outlined prioritization needs for the Groundwater and Soil Remediation Roadmap, concluded that contaminant behavior in the subsurface is poorly understood, and recommended further research in this area as a high priority. To address this NAS concern, the EM Office of Site Restoration began supporting the development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific approach that uses an integration of toolsets for understanding and predicting contaminant fate and transport in natural and engineered systems. The ASCEM modeling toolset is modular and open source. It is divided into three thrust areas: Multi-Process High Performance Computing (HPC), Platform and Integrated Toolsets, and Site Applications. The ASCEM toolsets will facilitate integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. During fiscal year 2012, the ASCEM project continued to make significant progress in capabilities development. Capability development occurred in both the Platform and Integrated Toolsets and Multi-Process HPC Simulator areas. The new Platform and Integrated Toolsets capabilities provide the user an interface and the tools necessary for end-to-end model development that includes conceptual model definition, data management for model input, model calibration and uncertainty analysis, and model output processing including visualization. The new HPC Simulator capabilities target increased functionality of process model representations, toolsets for interaction with the Platform, and model confidence testing and verification for

Human push capability.

Science.gov (United States)

Barnett, Ralph L; Liber, Theodore

2006-02-22

Use of unassisted human push capability arises from time to time in the areas of crowd and animal control, the security of locked doors, the integrity of railings, the removal of tree stumps and entrenched vehicles, the manoeuvering of furniture, and athletic pursuits such as US football or wrestling. Depending on the scenario, human push capability involves strength, weight, weight distribution, push angle, footwear/floor friction, and the friction between the upper body and the pushed object. Simple models are used to establish the relationships among these factors.

Oxygen-enhanced MRI for patients with connective tissue diseases: Comparison with thin-section CT of capability for pulmonary functional and disease severity assessment

Energy Technology Data Exchange (ETDEWEB)

Ohno, Yoshiharu, E-mail: yosirad@kobe-u.ac.jp [Advanced Biomedical Imaging Research Center, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Division of Functional and Diagnostic Imaging Research, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Nishio, Mizuho [Advanced Biomedical Imaging Research Center, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Division of Functional and Diagnostic Imaging Research, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Koyama, Hisanobu [Division of Radiology, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Yoshikawa, Takeshi; Matsumoto, Sumiaki [Advanced Biomedical Imaging Research Center, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Division of Functional and Diagnostic Imaging Research, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Seki, Shinichiro [Division of Radiology, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Tsubakimoto, Maho [Division of Radiology, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan); Department of Radiology, Graduate School of Medical Science, University of the Ryukyus, Nakagami-Gun, Okinawa (Japan); Sugimura, Kazuro [Division of Radiology, Department of Radiology, Kobe University Graduate School of Medicine, Kobe, Hyogo (Japan)

2014-02-15

Purpose: To prospectively and directly compare oxygen-enhanced (O{sub 2}-enhanced) MRI with thin-section CT for pulmonary functional loss and disease severity assessment in connective tissue disease (CTD) patients with interstitial lung disease (ILD). Materials and methods: Thin-section CT, O{sub 2}-enhanced MRI, pulmonary function test and serum KL-6 were administered to 36 CTD patients with ILD (23 men, 13 women; mean age: 63.9 years) and nine CTD patients without ILD (six men, and three women; mean age: 62.0 years). A relative-enhancement ratio (RER) map was generated from O{sub 2}-enhanced MRI and mean relative enhancement ratio (MRER) for each subject was calculated from all ROI measurements. CT-assessed disease severity was evaluated with a visual scoring system from each of the thin-section CT data. MRER and CT-assessed disease severities of CTD patients with and without ILD were then statistically compared. To assess capability for pulmonary functional loss and disease severity assessment in CTD patients, correlations of MRER and CT-assessed disease severity with pulmonary functional parameters and serum KL-6 in all subjects were statistically determined. Results: MRER and CT-assessed disease severity showed significant differences between CTD patients with (MRER: 0.15 ± 0.08, CT-assessed disease severity: 13.0 ± 7.4%) and without ILD (MRER: 0.25 ± 0.06, p = 0.0011; CT-assessed disease severity: 1.6 ± 1.6%, p < 0.0001). MRER and CT-assessed disease severity correlated significantly with pulmonary functional parameters and serum KL-6 in all subjects (0.61 ≤ r ≤ 0.79, p < 0.05). Conclusion: O{sub 2}-enhanced MRI was found to be as useful as thin-section CT for pulmonary functional loss and disease severity assessment of CTD patients with ILD.

Oxygen-enhanced MRI for patients with connective tissue diseases: Comparison with thin-section CT of capability for pulmonary functional and disease severity assessment

International Nuclear Information System (INIS)

Ohno, Yoshiharu; Nishio, Mizuho; Koyama, Hisanobu; Yoshikawa, Takeshi; Matsumoto, Sumiaki; Seki, Shinichiro; Tsubakimoto, Maho; Sugimura, Kazuro

2014-01-01

Purpose: To prospectively and directly compare oxygen-enhanced (O 2 -enhanced) MRI with thin-section CT for pulmonary functional loss and disease severity assessment in connective tissue disease (CTD) patients with interstitial lung disease (ILD). Materials and methods: Thin-section CT, O 2 -enhanced MRI, pulmonary function test and serum KL-6 were administered to 36 CTD patients with ILD (23 men, 13 women; mean age: 63.9 years) and nine CTD patients without ILD (six men, and three women; mean age: 62.0 years). A relative-enhancement ratio (RER) map was generated from O 2 -enhanced MRI and mean relative enhancement ratio (MRER) for each subject was calculated from all ROI measurements. CT-assessed disease severity was evaluated with a visual scoring system from each of the thin-section CT data. MRER and CT-assessed disease severities of CTD patients with and without ILD were then statistically compared. To assess capability for pulmonary functional loss and disease severity assessment in CTD patients, correlations of MRER and CT-assessed disease severity with pulmonary functional parameters and serum KL-6 in all subjects were statistically determined. Results: MRER and CT-assessed disease severity showed significant differences between CTD patients with (MRER: 0.15 ± 0.08, CT-assessed disease severity: 13.0 ± 7.4%) and without ILD (MRER: 0.25 ± 0.06, p = 0.0011; CT-assessed disease severity: 1.6 ± 1.6%, p < 0.0001). MRER and CT-assessed disease severity correlated significantly with pulmonary functional parameters and serum KL-6 in all subjects (0.61 ≤ r ≤ 0.79, p < 0.05). Conclusion: O 2 -enhanced MRI was found to be as useful as thin-section CT for pulmonary functional loss and disease severity assessment of CTD patients with ILD

Unpacking dynamic capability : a design perspective

NARCIS (Netherlands)

Mulders, D.E.M.; Romme, A.G.L.; Bøllingtoft, A.; Håkonsson, D.D.; Nielsen, J.F.; Snow, C.C; Ulhøi, J.

2009-01-01

This chapter reviews the dynamic capability literature to explore relationships between definition, operationalization, and measurement of dynamic capability. Subsequently, we develop a design-oriented approach toward dynamic capability that distinguishes between design rules, recurrent patterns of

Summary of Sandia Laboratories technical capabilities

International Nuclear Information System (INIS)

1977-05-01

The technical capabilities of Sandia Laboratories are detailed in a series of companion reports. In this summary the use of the capabilities in technical programs is outlined and the capabilities are summarized. 25 figures, 3 tables

Sandia Laboratories technical capabilities: testing

International Nuclear Information System (INIS)

Lundergan, C.D.

1975-12-01

The testing capabilities at Sandia Laboratories are characterized. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

An Assessment of Nondestructive Evaluation Capability for Complex Additive Manufacturing Aerospace Components

Science.gov (United States)

Walker, James; Beshears, Ron; Lambert, Dennis; Tilson, William

2016-01-01

The primary focus of this work is to investigate some of the fundamental relationships between processing, mechanical testing, materials characterization, and NDE for additively manufactured (AM) components using the powder bed fusion direct melt laser sintered process. The goal is to understand the criticality of defects unique to the AM process and then how conventional nondestructive evaluation methods as well as some of the more non-traditional methods such as computed tomography, are effected by the AM material. Specific defects including cracking, porosity and partially/unfused powder will be addressed. Besides line-of-site NDE, as appropriate these inspection capabilities will be put into the context of complex AM geometries where hidden features obscure, or inhibit traditional NDE methods.

Initial Verification and Validation Assessment for VERA

Energy Technology Data Exchange (ETDEWEB)

Dinh, Nam [North Carolina State Univ., Raleigh, NC (United States); Athe, Paridhi [North Carolina State Univ., Raleigh, NC (United States); Jones, Christopher [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Hetzler, Adam [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sieger, Matt [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-04-01

The Virtual Environment for Reactor Applications (VERA) code suite is assessed in terms of capability and credibility against the Consortium for Advanced Simulation of Light Water Reactors (CASL) Verification and Validation Plan (presented herein) in the context of three selected challenge problems: CRUD-Induced Power Shift (CIPS), Departure from Nucleate Boiling (DNB), and Pellet-Clad Interaction (PCI). Capability refers to evidence of required functionality for capturing phenomena of interest while capability refers to the evidence that provides confidence in the calculated results. For this assessment, each challenge problem defines a set of phenomenological requirements against which the VERA software is assessed. This approach, in turn, enables the focused assessment of only those capabilities relevant to the challenge problem. The evaluation of VERA against the challenge problem requirements represents a capability assessment. The mechanism for assessment is the Sandia-developed Predictive Capability Maturity Model (PCMM) that, for this assessment, evaluates VERA on 8 major criteria: (1) Representation and Geometric Fidelity, (2) Physics and Material Model Fidelity, (3) Software Quality Assurance and Engineering, (4) Code Verification, (5) Solution Verification, (6) Separate Effects Model Validation, (7) Integral Effects Model Validation, and (8) Uncertainty Quantification. For each attribute, a maturity score from zero to three is assigned in the context of each challenge problem. The evaluation of these eight elements constitutes the credibility assessment for VERA.

Capability Development in an Offshoring Context

DEFF Research Database (Denmark)

Jaura, Manya

Capability development can be defined as deliberate firm-level investment involving a search and learning process aimed at modifying or enhancing existing capabilities. Increasingly, firms are relocating advanced services to offshore locations resulting in the challenge of capability development ...

Sandia Laboratories technical capabilities: electronics

International Nuclear Information System (INIS)

Lundergan, C.D.

1975-12-01

This report characterizes the electronics capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

Combining Land Capability Evaluation, Geographic Information ...

African Journals Online (AJOL)

Combining Land Capability Evaluation, Geographic Information Systems, AnD Indigenous Technologies for Soil Conservation in Northern Ethiopia. ... Land capability and land use status were established following the procedures of a modified treatment-oriented capability classification using GIS. The case study ...

The financial and structural capabilities of key infrastructure sectors in Serbia

Directory of Open Access Journals (Sweden)

Malinić Dejan

2012-01-01

Full Text Available Experts and economic policy creators debate various economic growth rates without a direct insight into the capabilities of the different economic sectors motivated us to devote this paper to the research of key infrastructure sector capabilities, both in terms of the economic prosperity of the Serbian national economy and as a support for the development of other sectors. This paper examines the energy, transportation, and telecommunications sectors’ exposure to short-term and long-term risks, and assesses their financial strength, investment possibilities, and long-term profitability. We believe that the following results will be a valuable information input for making better strategic decisions and more expedient planning of economic sustainable growth.

Capability maturity models in engineering companies: case study analysis

Directory of Open Access Journals (Sweden)

Titov Sergei

2016-01-01

Full Text Available In the conditions of the current economic downturn engineering companies in Russia and worldwide are searching for new approaches and frameworks to improve their strategic position, increase the efficiency of the internal business processes and enhance the quality of the final products. Capability maturity models are well-known tools used by many foreign engineering companies to assess the productivity of the processes, to elaborate the program of business process improvement and to prioritize the efforts to optimize the whole company performance. The impact of capability maturity model implementation on cost and time are documented and analyzed in the existing research. However, the potential of maturity models as tools of quality management is less known. The article attempts to analyze the impact of CMM implementation on the quality issues. The research is based on a case study methodology and investigates the real life situation in a Russian engineering company.

Onboard Determination of Vehicle Glide Capability for Shuttle Abort Flight Managment (SAFM)

Science.gov (United States)

Straube, Timothy; Jackson, Mark; Fill, Thomas; Nemeth, Scott

2002-01-01

When one or more main engines fail during ascent, the flight crew of the Space Shuttle must make several critical decisions and accurately perform a series of abort procedures. One of the most important decisions for many aborts is the selection ofa landing site. Several factors influence the ability to reach a landing site, including the spacecraft point of atmospheric entry, the energy state at atmospheric entry, the vehicle glide capability from that energy state, and whether one or more suitable landing sites are within the glide capability. Energy assessment is further complicated by the fact that phugoid oscillations in total energy influence glide capability. Once the glide capability is known, the crew must select the "best" site option based upon glide capability and landing site conditions and facilities. Since most of these factors cannot currently be assessed by the crew in flight, extensive planning is required prior to each mission to script a variety of procedures based upon spacecraft velocity at the point of engine failure (or failures). The results of this preflight planning are expressed in tables and diagrams on mission-specific cockpit checklists. Crew checklist procedures involve leafing through several pages of instructions and navigating a decision tree for site selection and flight procedures - all during a time critical abort situation. With the advent of the Cockpit Avionics Upgrade (CAU), the Shuttle will have increased on-board computational power to help alleviate crew workload during aborts and provide valuable situational awareness during nominal operations. One application baselined for the CAU computers is Shuttle Abort Flight Management (SAFM), whose requirements have been designed and prototyped. The SAFM application includes powered and glided flight algorithms. This paper describes the glided flight algorithm which is dispatched by SAFM to determine the vehicle glide capability and make recommendations to the crew for site

Strategies for developing subchannel capability in an advanced system thermalhydraulic code: a literature review

International Nuclear Information System (INIS)

Cheng, J.; Rao, Y.F.

2015-01-01

In the framework of developing next generation safety analysis tools, Canadian Nuclear Laboratories (CNL) has planned to incorporate subchannel analysis capability into its advanced system thermalhydraulic code CATHENA 4. This paper provides a literature review and an assessment of current subchannel codes. It also evaluates three code-development methods: (i) static coupling of CATHENA 4 with the subchannel code ASSERT-PV, (ii) dynamic coupling of the two codes, and (iii) fully implicit implementation for a new, standalone CATHENA 4 version with subchannel capability. Results of the review and assessment suggest that the current ASSERT-PV modules can be used as the base for the fully implicit implementation of subchannel capability in CATHENA 4, and that this option may be the most cost-effective in the long run, resulting in savings in user application and maintenance costs. In addition, improved versatility of the tool could be accomplished by the addition of new features that could be added as part of its development. The new features would improve the capabilities of the existing subchannel code in handling low, reverse, and stagnant flows often encountered in system thermalhydraulic analysis. Therefore, the method of fully implicit implementation is preliminarily recommended for further exploration. A feasibility study will be performed in an attempt to extend the present work into a preliminary development plan. (author)

How does procurement capability maturity affect e-Procurement adoption and leverage purchasing in supply chain

Directory of Open Access Journals (Sweden)

Pongpanga Pongsuwan

2016-11-01

Full Text Available This study refers to the research model of Batenburg (2008 which defined procurement functions to six maturity dimensions; strategy, processes, control, organization, information, e-Technology as the starting point and indicates twenty two items to support capability maturity measurement which is called “Procurement Competitive Capability Maturity”(PCCM. This model is used for a company to assess current practices of procurement function and perceives the level of its capabilities. The data collection is from a survey of fifty-two selected procurement organizations in Southeast Asia (SEA countries; from Thailand, Vietnam, Philippines, Indonesia, Malaysia and Singapore. The objective of this study is to demonstrate the significant value of industry type, size of spending and centralized/decentralized procurement that affect procurement capability maturity. The results show that the industry has no relation to the capability maturity; the size of procurement spend has a positive relation to the capability maturity; and the centralized procurement has higher capability maturity than the decentralized. Moreover, this study extends the knowledge of e-Procurement and digital context to leverage procurement processes and visible procurement integration in an organization and across the supply chain.

Quantumness-generating capability of quantum dynamics

Science.gov (United States)

Li, Nan; Luo, Shunlong; Mao, Yuanyuan

2018-04-01

We study quantumness-generating capability of quantum dynamics, where quantumness refers to the noncommutativity between the initial state and the evolving state. In terms of the commutator of the square roots of the initial state and the evolving state, we define a measure to quantify the quantumness-generating capability of quantum dynamics with respect to initial states. Quantumness-generating capability is absent in classical dynamics and hence is a fundamental characteristic of quantum dynamics. For qubit systems, we present an analytical form for this measure, by virtue of which we analyze several prototypical dynamics such as unitary dynamics, phase damping dynamics, amplitude damping dynamics, and random unitary dynamics (Pauli channels). Necessary and sufficient conditions for the monotonicity of quantumness-generating capability are also identified. Finally, we compare these conditions for the monotonicity of quantumness-generating capability with those for various Markovianities and illustrate that quantumness-generating capability and quantum Markovianity are closely related, although they capture different aspects of quantum dynamics.

Organizational capabilities assessment: a dynamic methodology, methods and a tool for supporting organizational diagnosis

OpenAIRE

Rauffet , Philippe; Da Cunha , Catherine ,; Bernard , Alain

2010-01-01

Many methods, like CMMI, ISO norms or 5 steps roadmapping, are implemented in organizations in order to develop collective competencies, called also organizational capabilities, around organizational needs. They aim at providing new means to controls resources of organization, and enabling an organizational diagnosis, it is to say the evaluation of the strengths and the weaknesses of the organization. Nevertheless, these methods are generally based on knowledge based models (they are composed...

Intent, Capability and Opportunity: A Holistic Approach to Addressing Proliferation as a Risk Management Issue

International Nuclear Information System (INIS)

Rynes, Amanda; Bjornard, Trond

2011-01-01

Currently, proliferation risk assessment models are designed to evaluate only a portion of the overall risk, focusing exclusively on either technological or social factors to determine the extent of a threat. Many of these models are intended to act as a means of predicting proliferation potential rather than assessing the system as a whole, ignoring the ability to enhance mitigating factors and manage, rather just establish the presence of, the threat. While the information garnered through these forms of analysis is necessary, it remains incomplete. By incorporating political, social, economic and technical capabilities as well as human factors such as intent into a single, multi-faceted risk management model, proliferation risk can be evaluated more effectively. Framing this information around how to improve and expand the Regime already in place and establishing where there are gaps in the system allows for a more complete approach to risk management, mitigation and resource allocation. The research conducted here seeks to combine all three elements (intent, capability and opportunity) in a comprehensive evaluation which incorporates an assessment of state-level variables, possible proliferation pathways and technical capability. Each portion of the analysis is carried out independently then combined to illustrate the full scope of a State's nuclear infrastructure while showing areas of weakness in the institutional framework.

[The relationship between executive functions, physical and functional capability in people over 60 years old].

Science.gov (United States)

Rajtar-Zembaty, Anna; Sałakowski, Andrzej; Rajtar-Zembaty, Jakub

Nowadays it is believed that cognitive decline may contribute to the formation of gait disturbance and increased risk of falls. Currently the importance of executive functions to maintain proper control of gait is emphasized. The aim of the study was to assess the relationship between the level of executive function, functional and physical capability in patients over 60 years of age. The study included 300 patients (199 women and 101 men) aged 60-88 years. In order to screening for cognitive function Mini-Mental State Examination (MMSE) was used. The following researchers tools were used to conduct functional assessment: a) Short Physical Performance Battery (SPPB), b) Timed “Up and Go” (TUG) and c) Fast Walking Test. To assess executive fucntion Trail Making Test (TMT) was selected. The relationship between the speed of information processing (part A, TMT), executive functions (Part B, TMT), level of functional and physical capability was observed. The strongest positive correlation was noted between the time of TUG test and TMT part B (r=0.32; pphysical capability in patients over 60 years of age. Cognitive processes play an important role in the control of motor functions therefore it is important to incorporate examination of cognitive functions in the early geriatric diagnosis.

Distinctive Dynamic Capabilities for New Business Creation

DEFF Research Database (Denmark)

Rosenø, Axel; Enkel, Ellen; Mezger, Florian

2013-01-01

This study examines the distinctive dynamic capabilities for new business creation in established companies. We argue that these are very different from those for managing incremental innovation within a company's core business. We also propose that such capabilities are needed in both slow...... and fast-paced industries, and that similarities exist across industries. Hence, the study contributes to dynamic capabilities literature by: 1) identifying the distinctive dynamic capabilities for new business creation; 2) shifting focus away from dynamic capabilities in environments characterised by high...... clock-speed and uncertainty towards considering dynamic capabilities for the purpose of developing new businesses, which also implies a high degree of uncertainty. Based on interviews with 33 companies, we identify distinctive dynamic capabilities for new business creation, find that dynamic...

Organisational Capability--What Does It Mean?

Science.gov (United States)

National Centre for Vocational Education Research (NCVER), 2006

2006-01-01

Organisational capability is rapidly becoming recognized as the key to organizational success. However, the lack of research on it has been well documented in the literature, and organizational capability remains an elusive concept. Yet an understanding of organizational capability can offer insights into how RTOs might work most effectively,…

Resources and Capabilities of the Department of Veterans Affairs to Provide Timely and Accessible Care to Veterans

Science.gov (United States)

Hussey, Peter S.; Ringel, Jeanne S.; Ahluwalia, Sangeeta; Price, Rebecca Anhang; Buttorff, Christine; Concannon, Thomas W.; Lovejoy, Susan L.; Martsolf, Grant R.; Rudin, Robert S.; Schultz, Dana; Sloss, Elizabeth M.; Watkins, Katherine E.; Waxman, Daniel; Bauman, Melissa; Briscombe, Brian; Broyles, James R.; Burns, Rachel M.; Chen, Emily K.; DeSantis, Amy Soo Jin; Ecola, Liisa; Fischer, Shira H.; Friedberg, Mark W.; Gidengil, Courtney A.; Ginsburg, Paul B.; Gulden, Timothy; Gutierrez, Carlos Ignacio; Hirshman, Samuel; Huang, Christina Y.; Kandrack, Ryan; Kress, Amii; Leuschner, Kristin J.; MacCarthy, Sarah; Maksabedian, Ervant J.; Mann, Sean; Matthews, Luke Joseph; May, Linnea Warren; Mishra, Nishtha; Miyashiro, Lisa; Muchow, Ashley N.; Nelson, Jason; Naranjo, Diana; O'Hanlon, Claire E.; Pillemer, Francesca; Predmore, Zachary; Ross, Rachel; Ruder, Teague; Rutter, Carolyn M.; Uscher-Pines, Lori; Vaiana, Mary E.; Vesely, Joseph V.; Hosek, Susan D.; Farmer, Carrie M.

2016-01-01

Abstract The Veterans Access, Choice, and Accountability Act of 2014 addressed the need for access to timely, high-quality health care for veterans. Section 201 of the legislation called for an independent assessment of various aspects of veterans' health care. The RAND Corporation was tasked with an assessment of the Department of Veterans Affairs (VA) current and projected health care capabilities and resources. An examination of data from a variety of sources, along with a survey of VA medical facility leaders, revealed the breadth and depth of VA resources and capabilities: fiscal resources, workforce and human resources, physical infrastructure, interorganizational relationships, and information resources. The assessment identified barriers to the effective use of these resources and capabilities. Analysis of data on access to VA care and the quality of that care showed that almost all veterans live within 40 miles of a VA health facility, but fewer have access to VA specialty care. Veterans usually receive care within 14 days of their desired appointment date, but wait times vary considerably across VA facilities. VA has long played a national leadership role in measuring the quality of health care. The assessment showed that VA health care quality was as good or better on most measures compared with other health systems, but quality performance lagged at some VA facilities. VA will require more resources and capabilities to meet a projected increase in veterans' demand for VA care over the next five years. Options for increasing capacity include accelerated hiring, full nurse practice authority, and expanded use of telehealth. PMID:28083424

Development and capabilities: application to microcredit of a gender perspective

Directory of Open Access Journals (Sweden)

Emma Rué Cabré

2003-01-01

Full Text Available Since the 1980’s, we have seen growth in the popularity of microfinancing programs as a component of production projects and support projects for microenterprises in developing countries, because of their potential in the struggle against poverty and in favour of the empowerment of the most disadvantaged groups in the society, particularly women. On the basis of the capabilities theory of Amartya K. Sen and Martha C. Nussbaum, the article sets out to determine to what extent the microcredit can give rise to a process of transformation in the institutions that limit the economic, social and political opportunities of women and restrict their capability for realization. The analysis of the functioning of the market and interfamily relations from a gender perspective allows us to specify some of the positive effects of microcredits. At the same time, the analysis also brings out structural and organizational factors that may limit their impact, and looks at the challenges that organizations that manage this type of program have to meet in terms of design and assessment in order to guarantee that microfinancing promotes an institutional transformation that allows for a broadening of women’s capabilities.

Community psychology and the capabilities approach.

Science.gov (United States)

Shinn, Marybeth

2015-06-01

What makes for a good life? The capabilities approach to this question has much to offer community psychology, particularly with respect to marginalized groups. Capabilities are freedoms to engage in valued social activities and roles-what people can do and be given both their capacities, and environmental opportunities and constraints. Economist Amartya Sen's focus on freedoms and agency resonates with psychological calls for empowerment, and philosopher Martha Nussbaum's specification of requirements for a life that is fully human provides an important guide for social programs. Community psychology's focus on mediating structures has much to offer the capabilities approach. Parallels between capabilities, as enumerated by Nussbaum, and settings that foster positive youth development, as described in a National Research Council Report (Eccles and Gootman (Eds) in Community programs to promote youth development. National Academy Press, Washington, 2002) suggest extensions of the approach to children. Community psychologists can contribute to theory about ways to create and modify settings to enhance capabilities as well as empowerment and positive youth development. Finally, capabilities are difficult to measure, because they involve freedoms to choose but only choices actually made or enacted can be observed. The variation in activities or goals across members of a setting provides a measure of the capabilities that the setting fosters.

Effects of an Arctic Ocean Ski Traverse on the Protective Capabilities of Expedition Footwear

National Research Council Canada - National Science Library

Endrusick, Thomas; Frykman, Peter; O'Brien, Catherine; Giblo, Joseph

2005-01-01

A traverse of the Arctic Ocean during a 2000-km unsupported ski expedition provided an opportunity to assess the impact of an extreme cold environment on the protective capabilities of a specialized footwear system (FS...

U.S. Capability to Support Ocean Engineering in the Arctic.

Science.gov (United States)

1984-11-01

ntinudoladgsdvlpetlh Arctic will have an effect on its physical and biolociral U.S. Capability *to Support Ocean Engineering in the Arctic Committee on Assessment of...Richard J. Seymour * Exxon Production Research Scripps Institution of Oceanography - Houston, Texas La Jolla, California William Creelman William H... physical and biological environment. A subject of concern and controversy has been the potential effect that oil and gas activities may have on the

Size and transportation capabilities of the existing US cask fleet

International Nuclear Information System (INIS)

Danese, F.L.; Johnson, P.E.; Joy, D.S.

1990-01-01

This study investigates the current spent nuclear fuel cask fleet capability in the United States. In addition, it assesses the degree to which the current fleet would be available, as a contingency, until proposed Office of Civilian Radioactive Waste Management casks become operational. A limited fleet of ten spent fuel transportation casks is found to be readily available for use in Federal waste management efforts over the next decade

What am I capable? Self-Assessment of Basic Competences

OpenAIRE

Antonia Ramírez García; Carmen Corpas Reina; María Isabel Amor Almedina; Rocío Serrano Rodríguez

2014-01-01

The aims of this research are focus in evaluate linguistic communication and mathematics competences of students in sixth grade of primary education from their perception, and to develop a valid and reliable questionnaire in order to perform a self-assessment. The methodology has quantitative, descriptive and correlational character. In this research 1424 students from 46 schools in Cordova and its province participated. The results show that variables such as gender, age, number of siblings ...

Mechanism of supply chain coordination cased on dynamic capability framework-the mediating role of manufacturing capabilities

Directory of Open Access Journals (Sweden)

Tiantian Gao

2014-10-01

Full Text Available Purpose: A critical issue has been absent from the conversation on supply chain coordination: how supply chain coordination influence the enterprise performance. This research proposes a new vision to research the performance mechanism of supply chain coordination capability as a dynamic capability. Manufacturing capabilities are existed as mediating role. Design/methodology/approach: Data from International Manufacturing Strategy Survey in 2009 is used to verify the mediating model by hierarchical regression analysis. Findings: The results show that supply chain coordination impacts the enterprise performance positively and indirect impacts the enterprise performance through quality, cost, flexibility. Research implications: This study presents an overview of the impact of supply chain coordination and manufacturing capabilities on enterprise performance, giving grasp for further research of the relationships that exist between them. Originality/value: This finding integrates insights from previous research in dynamic capability framework and supply chain management into a generalization and extension of the performance mechanism in manufacturing enterprises.

Technological Dynamics and Social Capability

DEFF Research Database (Denmark)

Fagerberg, Jan; Feldman, Maryann; Srholec, Martin

2014-01-01

for the sample as a whole between 1998 and 2008. The results indicate that social capabilities, such as well-developed public knowledge infrastructure, an egalitarian distribution of income, a participatory democracy and prevalence of public safety condition the growth of technological capabilities. Possible...

Tolerance analysis in manufacturing using process capability ratio with measurement uncertainty

DEFF Research Database (Denmark)

Mahshid, Rasoul; Mansourvar, Zahra; Hansen, Hans Nørgaard

2017-01-01

. In this paper, a new statistical analysis was applied to manufactured products to assess achieved tolerances when the process is known while using capability ratio and expanded uncertainty. The analysis has benefits for process planning, determining actual precision limits, process optimization, troubleshoot......Tolerance analysis provides valuable information regarding performance of manufacturing process. It allows determining the maximum possible variation of a quality feature in production. Previous researches have focused on application of tolerance analysis to the design of mechanical assemblies...... malfunctioning existing part. The capability measure is based on a number of measurements performed on part’s quality variable. Since the ratio relies on measurements, elimination of any possible error has notable negative impact on results. Therefore, measurement uncertainty was used in combination with process...

Innovation value chain capability in Malaysian-owned company: A theoretical framework

Science.gov (United States)

Abidin, Norkisme Zainal; Suradi, Nur Riza Mohd

2014-09-01

Good quality products or services are no longer adequate to guarantee the sustainability of a company in the present competitive business. Prior research has developed various innovation models with the hope to better understand the innovativeness of the company. Due to countless definitions, indicators, factors, parameter and approaches in the study of innovation, it is difficult to ensure which one will best suit the Malaysian-owned company innovativeness. This paper aims to provide a theoretical background to support the framework of the innovation value chain capability in Malaysian-owned Company. The theoretical framework was based on the literature reviews, expert interviews and focus group study. The framework will be used to predict and assess the innovation value chain capability in Malaysian-owned company.

Managing corporate capabilities:theory and industry approaches.

Energy Technology Data Exchange (ETDEWEB)

Slavin, Adam M.

2007-02-01

This study characterizes theoretical and industry approaches to organizational capabilities management and ascertains whether there is a distinct ''best practice'' in this regard. We consider both physical capabilities, such as technical disciplines and infrastructure, and non-physical capabilities such as corporate culture and organizational procedures. We examine Resource-Based Theory (RBT), which is the predominant organizational management theory focused on capabilities. RBT seeks to explain the effect of capabilities on competitiveness, and thus provide a basis for investment/divestment decisions. We then analyze industry approaches described to us in interviews with representatives from Goodyear, 3M, Intel, Ford, NASA, Lockheed Martin, and Boeing. We found diversity amongst the industry capability management approaches. Although all organizations manage capabilities and consider them to some degree in their strategies, no two approaches that we observed were identical. Furthermore, we observed that theory is not a strong driver in this regard. No organization used the term ''Resource-Based Theory'', nor did any organization mention any other guiding theory or practice from the organizational management literature when explaining their capabilities management approaches. As such, we concluded that there is no single best practice for capabilities management. Nevertheless, we believe that RBT and the diverse industry experiences described herein can provide useful insights to support development of capabilities management approaches.

10 CFR 50.150 - Aircraft impact assessment.

Science.gov (United States)

2010-01-01

... maintained. (2) Aircraft impact characteristics.1 The assessment must be based on the beyond-design-basis... capabilities identified in paragraph (a)(1) of this section meet the assessment requirements in paragraph (a)(1... modified design features and functional capabilities continue to meet the assessment requirements in...

Capabilities and Equality of Health II

DEFF Research Database (Denmark)

Keiding, Hans

The concept of capabilities, introduced originally by Sen, has inspired many researchers but has not found any simple formal representation which might be instrumental in the construction of a comprehensive theory of equality. In a previous paper (Keiding, 2005), we investigated whether preferences...... of the capability approach to questions of health or equality. In the present paper we extend the notion of rationalizing orderings of capabilities to a dynamical context, in the sense that the utility function is not yet revealed to the individual at the time when the capabilities are ordered. It turns out...... over capabilities as sets of functionings can be rationalized by maximization of a suitable utility function over the set of functionings. Such a rationalization turned out to be possible only in cases which must be considered exceptional and which do not allowfor interesting applications...

PROCESS CAPABILITY ESTIMATION FOR NON-NORMALLY DISTRIBUTED DATA USING ROBUST METHODS - A COMPARATIVE STUDY

Directory of Open Access Journals (Sweden)

Yerriswamy Wooluru

2016-06-01

Full Text Available Process capability indices are very important process quality assessment tools in automotive industries. The common process capability indices (PCIs Cp, Cpk, Cpm are widely used in practice. The use of these PCIs based on the assumption that process is in control and its output is normally distributed. In practice, normality is not always fulfilled. Indices developed based on normality assumption are very sensitive to non- normal processes. When distribution of a product quality characteristic is non-normal, Cp and Cpk indices calculated using conventional methods often lead to erroneous interpretation of process capability. In the literature, various methods have been proposed for surrogate process capability indices under non normality but few literature sources offer their comprehensive evaluation and comparison of their ability to capture true capability in non-normal situation. In this paper, five methods have been reviewed and capability evaluation is carried out for the data pertaining to resistivity of silicon wafer. The final results revealed that the Burr based percentile method is better than Clements method. Modelling of non-normal data and Box-Cox transformation method using statistical software (Minitab 14 provides reasonably good result as they are very promising methods for non - normal and moderately skewed data (Skewness <= 1.5.

An Analysis of the Twenty-Nine Capabilities of the Marine Corps Expeditionary Unit (Special Operations Capable)

National Research Council Canada - National Science Library

Love, John

1998-01-01

... (Special Operations Capable) (MEU (SOC) to determine their relative validity. The methodology utilizes a multiple criteria decision-making model to determine the relative validity of each MEU (SOC) capability...

Capability approach

DEFF Research Database (Denmark)

Jensen, Niels Rosendal; Kjeldsen, Christian Christrup

Lærebogen er den første samlede danske præsentation af den af Amartya Sen og Martha Nussbaum udviklede Capability Approach. Bogen indeholder en præsentation og diskussion af Sen og Nussbaums teoretiske platform. I bogen indgår eksempler fra såvel uddannelse/uddannelsespolitik, pædagogik og omsorg....

Does STES-Oriented Science Education Promote 10th-Grade Students' Decision-Making Capability?

Science.gov (United States)

Levy Nahum, Tami; Ben-Chaim, David; Azaiza, Ibtesam; Herskovitz, Orit; Zoller, Uri

2010-07-01

Today's society is continuously coping with sustainability-related complex issues in the Science-Technology-Environment-Society (STES) interfaces. In those contexts, the need and relevance of the development of students' higher-order cognitive skills (HOCS) such as question-asking, critical-thinking, problem-solving and decision-making capabilities within science teaching have been argued by several science educators for decades. Three main objectives guided this study: (1) to establish "base lines" for HOCS capabilities of 10th grade students (n = 264) in the Israeli educational system; (2) to delineate within this population, two different groups with respect to their decision-making capability, science-oriented (n = 142) and non-science (n = 122) students, Groups A and B, respectively; and (3) to assess the pre-post development/change of students' decision-making capabilities via STES-oriented HOCS-promoting curricular modules entitled Science, Technology and Environment in Modern Society (STEMS). A specially developed and validated decision-making questionnaire was used for obtaining a research-based response to the guiding research questions. Our findings suggest that a long-term persistent application of purposed decision-making, promoting teaching strategies, is needed in order to succeed in affecting, positively, high-school students' decision-making ability. The need for science teachers' involvement in the development of their students' HOCS capabilities is thus apparent.

Evaluating late detection capability against diverse insider adversaries

International Nuclear Information System (INIS)

Sicherman, A.

1987-01-01

This paper describes a model for evaluating the late (after-the-fact) detection capability of material control and accountability (MCandA) systems against insider theft or diversion of special nuclear material. Potential insider cover-up strategies to defeat activities providing detection (e.g., inventories) are addressed by the model in a tractable manner. For each potential adversary and detection activity, two probabilities are assessed and used to fit the model. The model then computes the probability of detection for activities occurring periodically over time. The model provides insight into MCandA effectiveness and helps identify areas for safeguards improvement. 4 refs., 4 tabs

Assessment of nuclear medicine capabilities in responding to a radiological terrorism event. Technical memorandum

Energy Technology Data Exchange (ETDEWEB)

Stodilka, R.Z. [Univ. of Western Ontario, Schulich School of Medicine, London, Ontario (Canada); Wilkinson, D

2006-09-15

Substantial effort has been placed into enhancing federal capabilities for responding to a Chemical, Biological, Radiological, or Nuclear (CBRN) terrorist attack. However, little emphasis has been placed on including the local-level medical responders in these efforts. In effecting response to a radiological incident, potentially useful resources to access are health care professionals with training in matters of ionizing radiation, namely: nuclear medicine physicians, radiologists, radiation oncologists, medical physicists, and technologists. In this report, we focus on Nuclear Medicine expertise in Canada, and place this expertise into the context of assisting with a radiological terrorist incident. Nuclear Medicine expertise, along with its supporting infrastructure has already been deployed in proportion to the distribution of the civilian population. Given the expectations that the civilian population places in these health care professionals, their immediate access to specialized equipment, and the delay between a radiological terrorist incident and the arrival of federal expert capabilities, it is likely that these health care professionals will play important roles in emergency response. These roles will likely be: identifying the nature of the incident, triage, decontamination, coordinating with First Responders, and communicating with the media. Acknowledging the potential value of these professionals in responding to a radiological terrorist incident, steps should be taken to enlist their support and integrate them into a coherent national strategy. (author)

Assessment of nuclear medicine capabilities in responding to a radiological terrorism event. Technical memorandum

International Nuclear Information System (INIS)

Stodilka, R.Z.; Wilkinson, D.

2006-09-01

Substantial effort has been placed into enhancing federal capabilities for responding to a Chemical, Biological, Radiological, or Nuclear (CBRN) terrorist attack. However, little emphasis has been placed on including the local-level medical responders in these efforts. In effecting response to a radiological incident, potentially useful resources to access are health care professionals with training in matters of ionizing radiation, namely: nuclear medicine physicians, radiologists, radiation oncologists, medical physicists, and technologists. In this report, we focus on Nuclear Medicine expertise in Canada, and place this expertise into the context of assisting with a radiological terrorist incident. Nuclear Medicine expertise, along with its supporting infrastructure has already been deployed in proportion to the distribution of the civilian population. Given the expectations that the civilian population places in these health care professionals, their immediate access to specialized equipment, and the delay between a radiological terrorist incident and the arrival of federal expert capabilities, it is likely that these health care professionals will play important roles in emergency response. These roles will likely be: identifying the nature of the incident, triage, decontamination, coordinating with First Responders, and communicating with the media. Acknowledging the potential value of these professionals in responding to a radiological terrorist incident, steps should be taken to enlist their support and integrate them into a coherent national strategy. (author)

CASL Dakota Capabilities Summary

Energy Technology Data Exchange (ETDEWEB)

Adams, Brian M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Simmons, Chris [Univ. of Texas, Austin, TX (United States); Williams, Brian J. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-10

The Dakota software project serves the mission of Sandia National Laboratories and supports a worldwide user community by delivering state-of-the-art research and robust, usable software for optimization and uncertainty quantification. These capabilities enable advanced exploration and riskinformed prediction with a wide range of computational science and engineering models. Dakota is the verification and validation (V&V) / uncertainty quantification (UQ) software delivery vehicle for CASL, allowing analysts across focus areas to apply these capabilities to myriad nuclear engineering analyses.

Assessment of predictive capability of REFLA/TRAC code for large break LOCA transient in PWR using LOFT L2-5 test data

International Nuclear Information System (INIS)

Akimoto, Hajime; Ohnuki, Akira; Murao, Yoshio

1994-03-01

The REFLA/TRAC code is a best estimate code developed at Japan Atomic Energy Research Institute (JAERI) to provide advanced predictions of thermal hydraulic transient in light water reactors (LWRs). The REFLA/TRAC code uses the TRAC-PF1/MOD1 code as the framework of the code. The REFLA/TRAC code is expected to be used for the calibration of licensing codes, accident analysis, accident simulation of LWRs, and design of advanced LWRs. Several models have been implemented to the TRAC-PF1/MOD1 code at JAERI including reflood model, condensation model, interfacial and wall friction models, etc. These models have been verified using data from various separate effect tests. This report describes an assessment result of the REFLA/TRAC code, which was performed to assess the predictive capability for integral system behavior under large break loss of coolant accident (LBLOCA) using data from the LOFT L2-5 test. The assessment calculation confirmed that the REFLA/TRAC code can predict break mass flow rate, emergency core cooling water bypass and clad temperature excellently in the LOFT L2-5 test. The CPU time of the REFLA/TRAC code was about 1/3 of the TRAC-PF1/MOD1 code. The REFLA/TRAC code can perform stable and fast simulation of thermal hydraulic behavior in PWR LBLOCA with enough accuracy for practical use. (author)

Understanding dynamic capabilities through knowledge management

DEFF Research Database (Denmark)

Nielsen, Anders Paarup

2006-01-01

In the paper eight knowledge management activities are identified; knowledge creation, acquisition, capture, assembly, sharing, integration, leverage and exploitation. These activities are assembled into the three dynamic capabilities of knowledge development, knowledge (re......)combination and knowledge use. The dynamic capabilities and the associated knowledge management activities create flows to and from the firm’s stock of knowledge and they support the creation and use of organizational capabilities....

Technological Capability's Predictor Variables

Directory of Open Access Journals (Sweden)

Fernanda Maciel Reichert

2011-03-01

Full Text Available The aim of this study was to identify the factors that influence in configuration of the technological capability of companies in sectors with medium-low technological intensity. To achieve the goal proposed in this article a survey was carried out. Based on the framework developed by Lall (1992 which classifies firms in basic, intermediate and advanced level of technological capability; it was found that the predominant technological capability is intermediate, with 83.7% of respondent companies (plastics companies in Brazil. It is believed that the main contribution of this study is the finding that the dependent variable named “Technological Capability” can be explained at a rate of 65% by six variables: development of new processes; selection of the best equipment supplier; sales of internally developed new technology to third parties; design and manufacture of equipment; study of the work methods and perform inventory control; and improvement of product quality.

Intent, Capability and Opportunity: A Holistic Approach to Addressing Proliferation as a Risk Management Issue

Energy Technology Data Exchange (ETDEWEB)

Amanda Rynes; Trond Bjornard

2011-07-01

Currently, proliferation risk assessment models are designed to evaluate only a portion of the overall risk, focusing exclusively on either technological or social factors to determine the extent of a threat. Many of these models are intended to act as a means of predicting proliferation potential rather than assessing the system as a whole, ignoring the ability to enhance mitigating factors and manage, rather just establish the presence of, the threat. While the information garnered through these forms of analysis is necessary, it remains incomplete. By incorporating political, social, economic and technical capabilities as well as human factors such as intent into a single, multi-faceted risk management model, proliferation risk can be evaluated more effectively. Framing this information around how to improve and expand the Regime already in place and establishing where there are gaps in the system allows for a more complete approach to risk management, mitigation and resource allocation. The research conducted here seeks to combine all three elements (intent, capability and opportunity) in a comprehensive evaluation which incorporates an assessment of state-level variables, possible proliferation pathways and technical capability. Each portion of the analysis is carried out independently then combined to illustrate the full scope of a State's nuclear infrastructure while showing areas of weakness in the institutional framework.

Dynamic capabilities and innovation management: a conceptual approach

Directory of Open Access Journals (Sweden)

Jose Javier Aguilar Zambrano

2006-07-01

Full Text Available Organizational capabilities are those behavioral routines oriented to develop a specific task (NELSON; WINTER, 1982. These capabilities define what the company knows to do and how must to do it. Nevertheless, the repetitive character of these capabilities could be producing stopped processes (METCALFE, 1995 which both limit the generation of new capabilities and diminishing the dynamism in the production, reproduction and reconfiguration of new capabilities (TEECE; PISANO, 1997. This article compares and analyzes different theoretical-conceptual perspectives for generation and reconfiguration of technological capabilities within an organization. Additionally this article suggests that dynamic capabilities to make feasible innovation processes within an organization. The general concept of dynamic capacities will be used like driver of changes to produce and reconfigurate capabilities in the organization. The glance of the dynamic capabilities allows understanding the complexity of the creation, development and use of capabilities. This understanding could constitute material fundamental to manage learning processes and organizational change oriented to innovation.

Associations between structural capabilities of primary care practices and performance on selected quality measures.

Science.gov (United States)

Friedberg, Mark W; Coltin, Kathryn L; Safran, Dana Gelb; Dresser, Marguerite; Zaslavsky, Alan M; Schneider, Eric C

2009-10-06

Recent proposals to reform primary care have encouraged physician practices to adopt such structural capabilities as performance feedback and electronic health records. Whether practices with these capabilities have higher performance on measures of primary care quality is unknown. To measure associations between structural capabilities of primary care practices and performance on commonly used quality measures. Cross-sectional analysis. Massachusetts. 412 primary care practices. During 2007, 1 physician from each participating primary care practice (median size, 4 physicians) was surveyed about structural capabilities of the practice (responses representing 308 practices were obtained). Data on practice structural capabilities were linked to multipayer performance data on 13 Healthcare Effectiveness Data and Information Set (HEDIS) process measures in 4 clinical areas: screening, diabetes, depression, and overuse. Frequently used multifunctional electronic health records were associated with higher performance on 5 HEDIS measures (3 in screening and 2 in diabetes), with statistically significant differences in performance ranging from 3.1 to 7.6 percentage points. Frequent meetings to discuss quality were associated with higher performance on 3 measures of diabetes care (differences ranging from 2.3 to 3.1 percentage points). Physician awareness of patient experience ratings was associated with higher performance on screening for breast cancer and cervical cancer (1.9 and 2.2 percentage points, respectively). No other structural capabilities were associated with performance on more than 1 measure. No capabilities were associated with performance on depression care or overuse. Structural capabilities of primary care practices were assessed by physician survey. Among the investigated structural capabilities of primary care practices, electronic health records were associated with higher performance across multiple HEDIS measures. Overall, the modest magnitude and

Human Exploration Systems and Mobility Capability Roadmap Progress Review

Science.gov (United States)

Culbert, Chris; Taylor, Jeff

2005-01-01

Contents include the following: Capability Roadmap Team. Capability Description and Capability Breakdown Structure. Benefits of the Human Systems and Mobility Capability. Roadmap Process and Approach. Drivers and Assumptions for the whole team. Current State-of-the-Art, Assumptions and Requirements will be covered in the appropriate sections. Capability Presentations by Leads under Roadmap (Repeated for each capability under roadmap). Capability Description, Benefits, Current State-of-the-Art. Capability Requirements and Assumptions. Roadmap for Capability. Capability Readiness Level. Technology Readiness Level. Figures of Merit. Summary of Top Level Capability. Significant Technical Challenges. Summary and Forward Work.

Using pliers in assembly work: short and long task duration effects of gloves on hand performance capabilities and subjective assessments of discomfort and ease of tool manipulation.

Science.gov (United States)

Dianat, Iman; Haslegrave, Christine M; Stedmon, Alex W

2012-03-01

The present study investigated the effects of wearing typical industrial gloves on hand performance capabilities (muscle activity, wrist posture, touch sensitivity, hand grip and forearm torque strength) and subjective assessments for an extended duration of performing a common assembly task, wire tying with pliers, which requires a combination of manipulation and force exertion. Three commercially available gloves (cotton, nylon and nitrile gloves) were tested and compared with a bare hand condition while participants performed the simulated assembly task for 2 h. The results showed that wearing gloves significantly increased the muscle activity, wrist deviation, and discomfort whilst reducing hand grip strength, forearm torque strength and touch sensitivity. The combined results showed that the length of time for which gloves are worn does affect hand performance capability and that gloves need to be evaluated in a realistic working context. The results are discussed in terms of selection of gloves for industrial assembly tasks involving pliers. Copyright © 2011 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Size and transportation capabilities of the existing U.S. cask fleet

International Nuclear Information System (INIS)

Danese, F.L.; Johnson, P.E.; Joy, D.S.

1990-01-01

This paper investigates the current spent nuclear fuel cask fleet capability in the United States. It assesses the degree to which the current fleet would be available, as a contingency, until proposed Office of Civilian Radioactive Waste Management casks become operational. A limited fleet of ten spent fuel transportation casks is found to be readily available for use in Federal waste management efforts over the next decade

Evaluation of swimming capability and potential velocity barrier problems for fish. Part B: New telemetric approaches to the assessment of fish swimming performance

International Nuclear Information System (INIS)

Scruton, D. A.; Goosney, R. G.; McKinley, R. S.; Booth, R. K.; Colavecchia, M.

1998-08-01

This report represents the second part of a study undertaken to develop information related to swimming capability of several important fish species. The study will provide biological design criteria to mitigate potential velocity barrier problems associated with hydroelectric power plants. This part of the report focuses on the development and evaluation of approaches to assessing locomotory activity, swimming performance and energy load costs to fish under naturally occurring conditions and in relation to potential barriers. The study involved implantation of a bio-sensitive radio transmitter (electromyogram (EMG)) tag in the swimming muscle of fish, calibration of locomotory ability and energetic scope, and subsequent use of EMG signals to assess swimming performance and metabolic costs in situ. Digital signal processing (DSP) with antennae switching was also used to study high speed swimming performance, behaviour, and migratory strategy in relation to ascent of an experimental flume. The techniques and technologies developed indicate the complexity of factors that regulate fish swimming energy expenditure that need to be considered in the design and operation of fish passage facilities. 84 refs., 6 tabs., figs., 2 appendices

Identifying 21st Century Capabilities

Science.gov (United States)

Stevens, Robert

2012-01-01

What are the capabilities necessary to meet 21st century challenges? Much of the literature on 21st century skills focuses on skills necessary to meet those challenges associated with future work in a globalised world. The result is a limited characterisation of those capabilities necessary to address 21st century social, health and particularly…

Integrated System Health Management (ISHM): Systematic Capability Implementation

Science.gov (United States)

Figueroa, Fernando; Holland, Randy; Schmalzwel, John; Duncavage, Dan

2006-01-01

This paper provides a credible approach for implementation of ISHM capability in any system. The requirements and processes to implement ISHM capability are unique in that a credible capability is initially implemented at a low level, and it evolves to achieve higher levels by incremental augmentation. In contrast, typical capabilities, such as thrust of an engine, are implemented once at full Functional Capability Level (FCL), which is not designed to change during the life of the product. The approach will describe core ingredients (e.g. technologies, architectures, etc.) and when and how ISHM capabilities may be implemented. A specific architecture/taxonomy/ontology will be described, as well as a prototype software environment that supports development of ISHM capability. This paper will address implementation of system-wide ISHM as a core capability, and ISHM for specific subsystems as expansions and evolution, but always focusing on achieving an integrated capability.

A framework for offshore vendor capability development

Science.gov (United States)

Yusuf Wibisono, Yogi; Govindaraju, Rajesri; Irianto, Dradjad; Sudirman, Iman

2016-02-01

Offshore outsourcing is a common practice conducted by companies, especially in developed countries, by relocating one or more their business processes to other companies abroad, especially in developing countries. This practice grows rapidly owing to the ease of accessing qualified vendors with a lower cost. Vendors in developing countries compete more intensely to acquire offshore projects. Indonesia is still below India, China, Malaysia as main global offshore destinations. Vendor capability is among other factors that contribute to the inability of Indonesian vendor in competing with other companies in the global market. Therefore, it is essential to study how to increase the vendor's capability in Indonesia, in the context of global offshore outsourcing. Previous studies on the vendor's capability mainly focus on capabilities without considering the dynamic of capabilities due to the environmental changes. In order to be able to compete with competitors and maintain the competitive advantage, it is necessary for vendors to develop their capabilities continuously. The purpose of this study is to develop a framework that describes offshore vendor capability development along the client-vendor relationship stages. The framework consists of three main components, i.e. the stages of client-vendor relationship, the success of each stage, and the capabilities of vendor at each stage.

Compilation of Sandia Laboratories technical capabilities

International Nuclear Information System (INIS)

Lundergan, C.D.; Mead, P.L.

1975-11-01

This report is a compilation of 17 individual documents that together summarize the technical capabilities of Sandia Laboratories. Each document in this compilation contains details about a specific area of capability. Examples of application of the capability to research and development problems are provided. An eighteenth document summarizes the content of the other seventeen. Each of these documents was issued with a separate report number (SAND 74-0073A through SAND 74-0091, except -0078)

A Stochastic Model for the Landing Dispersion of Hazard Detection and Avoidance Capable Flight Systems

Science.gov (United States)

Witte, L.

2014-06-01

To support landing site assessments for HDA-capable flight systems and to facilitate trade studies between the potential HDA architectures versus the yielded probability of safe landing a stochastic landing dispersion model has been developed.

Towards a dynamic concept of alliance capability

OpenAIRE

SLUYTS, Kim; MARTENS, Rudy; MATTHYSSENS, Paul

2008-01-01

This paper has a threefold purpose. First, we offer a literature review on alliance capability based on strategic and competence based management literature. Second, we extend existing literature on alliance capability by breaking this concept down into five sub capabilities, which are each linked to a stage of the alliance life cycle. Finally, we suggest how firms can support these capabilities through structural, technological and people-related tools and techniques. We argue that current l...

The Organizational Economics of Organizational Capability and Heterogeneity

DEFF Research Database (Denmark)

Foss, Nicolai Juul; Argyres, Nicholas; Felin, Teppo

For decades, the literatures on firm capabilities and organizational economics have been at odds with each other, specifically relative to explaining organizational boundaries and heterogeneity. We briefly trace the history of the relationship between the capabilities literature and organizational...... economics and point to the dominance of a “capabilities first” logic in this relationship. We argue that capabilities considerations are inherently intertwined with questions about organizational boundaries and internal organization, and use this point to respond to the prevalent “capabilities first” logic....... We offer an integrative research agenda that focuses, first, on the governance of capabilities and, second, on the capability of governance....

a Capability approach

African Journals Online (AJOL)

efforts towards gender equality in education as a means of achieving social justice. ... should mean that a lot of capability approach-oriented commentators are ... processes, their forms of exercising power, and their rules, unwritten cultures, ...

Compilation of Sandia Laboratories technical capabilities

Energy Technology Data Exchange (ETDEWEB)

Lundergan, C. D.; Mead, P. L. [eds.

1975-11-01

This report is a compilation of 17 individual documents that together summarize the technical capabilities of Sandia Laboratories. Each document in this compilation contains details about a specific area of capability. Examples of application of the capability to research and development problems are provided. An eighteenth document summarizes the content of the other seventeen. Each of these documents was issued with a separate report number (SAND 74-0073A through SAND 74-0091, except -0078). (RWR)

Sandia Laboratories technical capabilities: engineering analysis

International Nuclear Information System (INIS)

Lundergan, C.D.

1975-12-01

This report characterizes the engineering analysis capabilities at Sandia Laboratories. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs

High Performance Affinity Chromatography of Antithrombin III Based on Monodisperse Poly (glycidyl methacrylate) Beads

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

A new approach for the separation of antithrombin III with high performance affinity chromatography (HPAC) was described. A novel monodisperse,non-porous,cross-linked poly (glycidyl methacrylate) beads (PGMA) were used as the affinity support. With the water-soluble carbodiimide,heparin was linked covalently to amino-PGMA-beads,which was prepared by amination of PGMA. The adsorbent obtained exhibits high binding activity to antithrombin III (ATIII),good resolution and excellent mechanical properties and can be used under high flow rate.

Study on spoilage capability and VBNC state formation and recovery of Lactobacillus plantarum.

Science.gov (United States)

Liu, Junyan; Li, Lin; Li, Bing; Peters, Brian M; Deng, Yang; Xu, Zhenbo; Shirtliff, Mark E

2017-09-01

The present study aimed at investigating the capability of L. plantarum strain BM-LP14723 to enter into and recover from the viable but nonculturable (VBNC) state and to cause beer spoilage. VBNC state was induced by incubating in beer with subculturing or low temperature treatment. Culturable, total, and viable cells numbers were assessed by MRS agar plate counting, acridine orange direct counting, and Live/Dead BacLight bacterial viability kit, respectively. Organic acids concentrations were measured by reversed-phase high performance liquid chromatography. VBNC L. plantarum cells were detected after 189 ± 1.9 days low temperature treatment or 29 ± 0.7 subcultures in beer. The VBNC L. plantarum retained spoilage capability. Addition of catalase is an effective method for the recovery of the VBNC L. plantarum cells. L. plantarum strain BM-LP14723 is capable of entering into and recovery from the VBNC state and maintained spoilage capability. The current study presented that beer-spoilage L. plantarum can hide both in breweries and during transporting and marketing process and thus lead to beer-spoilage incidents. Copyright © 2017 Elsevier Ltd. All rights reserved.

Global dynamics, capabilities and the crisis

Czech Academy of Sciences Publication Activity Database

Fagerberg, J.; Srholec, Martin

2016-01-01

Roč. 26, č. 4 (2016), s. 765-784 ISSN 0936-9937 Institutional support: PRVOUK-P23 Keywords : technological capabilities * social capabilities * competitiveness Subject RIV: AH - Economics Impact factor: 0.862, year: 2016

Sandia Laboratories technical capabilities: systems analysis

International Nuclear Information System (INIS)

Lundergan, C.D.

1975-06-01

The systems analysis capabilities at Sandia Laboratories are summarized. Selected applications of these capabilities are presented to illustrate the extent to which they can be applied in research and development programs. (U.S.)

Technological capability at the Brazilian official pharmaceutical laboratories

Directory of Open Access Journals (Sweden)

José Vitor Bomtempo Martins

2008-10-01

Full Text Available This paper studies the technological capability in the Brazilian Official Pharmaceutical Laboratories [OPL]. The technological capability analysis could contribute to organization strategies and governmental actions in order to improve OPL basic tasks as well to incorporate new ones, particularly concerning the innovation management. Inspired in Figueiredo (2000, 2003a, 2003b and Figueiredo and Ariffin (2003, a framework was drawn and adapted to pharmaceutical industry characteristics and current sanitary and health legislation. The framework allows to map different dimensions of the technological capability (installations, processes, products, equipments, organizational capability and knowledge management and the level attained by OPL (ordinary or innovating capability. OPL show a good development of ordinary capabilities, particularly in Product and Processes. Concerning the other dimensions, OPL are quite diverse. In general, innovating capabilities are not much developed. In the short term, it was identified a dispersion in the capacitating efforts. Considering their present level and the absorption efforts, good perspectives can be found in Installations, Processes and Organizational Capability. A lower level of efforts in Products and Knowledge Management could undermine these capabilities in the future.

Land Capability Analysis on Farming System at Serang Sub-Watershed Kedung Ombo Reservoir Catchment Area

Directory of Open Access Journals (Sweden)

Jaka Suyana

2014-07-01

Full Text Available Soil conservation in principle is using the land according to its capability and keep them from damage. This study aims at assessing the land capability classes of farming systems at Serang sub-watershed and evaluate their usages. The results showed that the land capability dominated by Class II (12,096.90 ha, 40.6%, followed by Class III (11,598.92 ha, 38.9%, Class IV (2,879.11 ha, 9.7%, Class I (1,333.14 ha, 4.5%, Class VIII (712.57 ha, 2.4%, Class VII (684.97 ha, 2.3% and Class VI (512.84 ha, 1.7%. The main resistance factors are slope and soil deepth for class II; slope, soil deepth, drainage and erosion for class III; slope and erosion for class IV; and slope for class VIII, VII and VI. The results showed that 94% farm lands at Serang sub-watershed was suitable to its land capability and only 6.0% were not suitable.

Organizational capabilities and bottom line performance : The relationship between organizational architecture and strategic performance of business units in Dutch headquartered multinationals

NARCIS (Netherlands)

Eikelenboom, B.L.

2005-01-01

This study addresses a key question in business: do organizational capabilities relate to bottom line performance? It is a hard struggle to assess intangible, organizational capabilities, but due to web-based technology, serious advances have been made to measure organizational architecture, a

Dynamic capabilities and innovation: a Multiple-Case Study

OpenAIRE

Bravo Ibarra, Edna Rocío; Mundet Hiern, Joan; Suñé Torrents, Albert

2009-01-01

After a detailed survey of the scientific literature, it was found that several characteristics of dynamic capabilities were similar to those of innovation capability. Therefore, with a deeper study of the first ones, it could be possible to design a model aimed to structure innovation capability. Thus, this work presents a conceptual model, where the innovation capability is shown as result of three processes: knowledge absorption and creation capability, knowledge integration and knowledge ...

MODERN CAPABILITIES OF BREAST PATHOLOGY DIAGNOSTICS

Directory of Open Access Journals (Sweden)

I. V. Vysotskaya

2015-01-01

Full Text Available Every year more than 1 million new cases of breast cancer are being recorded worldwide. Choice of appropriate tactics of treatment depends on the timely diagnosis and correct assessment of the prevalence of cancer.The algorithm of patient»s examination includes clinical examination, X-ray mammography and ultrasonic diagnosis of breast. However, this is not sufficient for a complete interpretation of the patient»s condition in case of non-palpable breast formations, ambiguous interpretation of imaging under structural changes, increased density of breast tissue, etc.In this regard, the introduction of new technologies and their evaluation in terms of practicality is a logical and developing method of early diagnosis of breast pathology.One of the methods that enables enhancing the information capability of ultrasonic diagnosis of breast is elastography. It allows for the differential diagnosis of benign and malignant changes not only in the breast tissue, but also in the areas of regional lymph drainage.Promising method of modern diagnostic breast care is digital mammography tomosynthesis. However, in spite of the first and very optimisticdata, this technique is still far from standard.Complex diagnostics of breast pathology, in addition to clinical data and imaging results, are based on information obtained from biopsies. At the present stage core-biopsy is considered as the best way of verification, where the resulting material is subjected to immunohistochemical studies.Thus, the spectrum of diagnostic capabilities is constantly expanding. Highly informative techniques included in the daily practice today enable clinicians to achieve optimal results in curing even greater number of patients.

Investigating SWOT's capabilities to detect meso and submesoscale eddies in the western Mediterranean

Science.gov (United States)

Gomez-Navarro, Laura; Pascual, Ananda; Fablet, Ronan; Mason, Evan

2017-04-01

The primary oceanographic objective of the future Surface Water Ocean Topography (SWOT) altimetric satellite is to characterize the mesoscale and submesoscale ocean circulation. The aim of this study is to assess the capabilities of SWOT to resolve the meso and submesoscale in the western Mediterranean. With ROMS model data as inputs for the SWOT simulator, pseudo-SWOT data were generated. These data were compared with the original ROMS model data and ADT data from present day altimetric satellites to assess the temporal and spatial resolution of SWOT in the western Mediterranean. We then addressed the removal of the satellite's noise in the pseudo-SWOT data using a Laplacian diffusion. We investigated different parameters of the filter by looking at their impact on the spatial spectra and RMSEs calculated from the simulator outputs. To further assess the satellites capabilities, we derived absolute geostrophic velocities and relative vorticity. Our numerical experiments show that the noise patterns affect the spectral content of the pseudo-SWOT fields below 30 km. The Laplacian diffusion improves the recovery of the spectral signature of the altimetric field, especially down to 20 km. With the help of this filter, we manage to observe small scale oceanic features in pseudo-SWOT data, and in its derived variables.

Disability, Capability, and Special Education: Towards a Capability-Based Theory

Science.gov (United States)

Reindal, Solveig Magnus

2009-01-01

The main objective of the article was to investigate the claim that the capability approach fares better with an understanding of disability as presented by the World Health Organization's "International Classification of Functioning, Disability and Health" (ICF) than by the social model, which has been promoted within disability studies. Scholars…

Selecting Capabilities for Quality of Life Measurement

Science.gov (United States)

Robeyns, Ingrid

2005-01-01

The capability approach advocates that interpersonal comparisons be made in the space of functionings and capabilities. However, Amartya Sen has not specified which capabilities should be selected as the relevant ones. This has provoked two types of criticism. The stronger critique is Martha Nussbaum's claim that Sen should endorse one specific…

An Agency-based Capability Theory of Justice

NARCIS (Netherlands)

Claassen, R.J.G.

2017-01-01

The capability approach is one of the main contenders in the field of theorizing social justice. Each citizen is entitled to a set of basic capabilities. But which are these? Martha Nussbaum formulated a set of ten central capabilities. Amartya Sen argued they should be selected in a process of

RCTA capstone assessment

Science.gov (United States)

Lennon, Craig; Bodt, Barry; Childers, Marshal; Dean, Robert; Oh, Jean; DiBerardino, Chip; Keegan, Terence

2015-05-01

The Army Research Laboratory's Robotics Collaborative Technology Alliance (RCTA) is a program intended to change robots from tools that soldiers use into teammates with which soldiers can work. This requires the integration of fundamental and applied research in perception, artificial intelligence, and human-robot interaction. In October of 2014, the RCTA assessed progress towards integrating this research. This assessment was designed to evaluate the robot's performance when it used new capabilities to perform selected aspects of a mission. The assessed capabilities included the ability of the robot to: navigate semantically outdoors with respect to structures and landmarks, identify doors in the facades of buildings, and identify and track persons emerging from those doors. We present details of the mission-based vignettes that constituted the assessment, and evaluations of the robot's performance in these vignettes.

DDP-516 Computer Graphics System Capabilities

Science.gov (United States)

1972-06-01

This report describes the capabilities of the DDP-516 Computer Graphics System. One objective of this report is to acquaint DOT management and project planners with the system's current capabilities, applications hardware and software. The Appendix i...

ENTREPRENEURIAL CAPABILITIES

DEFF Research Database (Denmark)

Rasmussen, Lauge Baungaard; Nielsen, Thorkild

2003-01-01

The aim of this article is to analyse entrepreneurship from an action research perspective. What is entrepreneurship about? Which are the fundamental capabilities and processes of entrepreneurship? To answer these questions the article includes a case study of a Danish entrepreneur and his networ....... Finally, the article discuss, how more long term action research methods could be integrated into the entrepreneurial processes and the possible impacts of such an implementation?...

Implications of Extension of Station Blackout Cooping Capability on Nuclear Power Plant Safety

International Nuclear Information System (INIS)

Volkanovski, Andrija

2015-01-01

The safety of the nuclear power plant depends on the availability of the continuous and reliable sources of electrical energy during all modes of operation of the plant. The station blackout corresponds to a total loss of all alternate current (AC) power as a result of complete failure of both offsite and on-site AC power sources. The electricity for the essential systems during station blackout is provided from the batteries installed in the nuclear power plant. The results of the probabilistic safety assessment show that station blackout is one of the main and frequently the dominant contributor to the core damage frequency. Results of the analysis of the implications of the strengthening of the SBO mitigation capability on safety of the NPP will be presented. The assessment is done with state-of-art deterministic and probabilistic methods and tolls with application on reference models of nuclear power plants. The safety analysis is done on reference model of the nuclear power plant. Obtained results show large decrease of the core damage frequency with strengthening of the station blackout mitigation capability. The time extension of blackout coping capability results in the delay of the core heat up for at least the extension time interval. Availability and operation of the steam driven auxiliary feedwater system maintains core integrity up to 72 h after the successful shutdown, even in the presence of the reactor coolant pumps seal leakage. The largest weighted decrease of the core damage frequency considering the costs for the modification is obtained for the modification resulting in extension of the station blackout coping capability. The importance of the common cause failures of the emergency diesel generators for the obtained decrease of the core damage frequency and overall safety of the plant is identified in the obtained results. (authors)

The new MCNP6 depletion capability

International Nuclear Information System (INIS)

Fensin, M. L.; James, M. R.; Hendricks, J. S.; Goorley, J. T.

2012-01-01

The first MCNP based in-line Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. Both the MCNP5 and MCNPX codes have historically provided a successful combinatorial geometry based, continuous energy, Monte Carlo radiation transport solution for advanced reactor modeling and simulation. However, due to separate development pathways, useful simulation capabilities were dispersed between both codes and not unified in a single technology. MCNP6, the next evolution in the MCNP suite of codes, now combines the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. We describe here the new capabilities of the MCNP6 depletion code dating from the official RSICC release MCNPX 2.6.0, reported previously, to the now current state of MCNP6. NEA/OECD benchmark results are also reported. The MCNP6 depletion capability enhancements beyond MCNPX 2.6.0 reported here include: (1) new performance enhancing parallel architecture that implements both shared and distributed memory constructs; (2) enhanced memory management that maximizes calculation fidelity; and (3) improved burnup physics for better nuclide prediction. MCNP6 depletion enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code. The enhancements described here help provide a powerful capability as well as dictate a path forward for future development to improve the usefulness of the technology. (authors)

The New MCNP6 Depletion Capability

International Nuclear Information System (INIS)

Fensin, Michael Lorne; James, Michael R.; Hendricks, John S.; Goorley, John T.

2012-01-01

The first MCNP based inline Monte Carlo depletion capability was officially released from the Radiation Safety Information and Computational Center as MCNPX 2.6.0. Both the MCNP5 and MCNPX codes have historically provided a successful combinatorial geometry based, continuous energy, Monte Carlo radiation transport solution for advanced reactor modeling and simulation. However, due to separate development pathways, useful simulation capabilities were dispersed between both codes and not unified in a single technology. MCNP6, the next evolution in the MCNP suite of codes, now combines the capability of both simulation tools, as well as providing new advanced technology, in a single radiation transport code. We describe here the new capabilities of the MCNP6 depletion code dating from the official RSICC release MCNPX 2.6.0, reported previously, to the now current state of MCNP6. NEA/OECD benchmark results are also reported. The MCNP6 depletion capability enhancements beyond MCNPX 2.6.0 reported here include: (1) new performance enhancing parallel architecture that implements both shared and distributed memory constructs; (2) enhanced memory management that maximizes calculation fidelity; and (3) improved burnup physics for better nuclide prediction. MCNP6 depletion enables complete, relatively easy-to-use depletion calculations in a single Monte Carlo code. The enhancements described here help provide a powerful capability as well as dictate a path forward for future development to improve the usefulness of the technology.

Evaluating Internal Technological Capabilities in Energy Companies

Directory of Open Access Journals (Sweden)

Mingook Lee

2016-03-01

Full Text Available As global competition increases, technological capability must be evaluated objectively as one of the most important factors for predominance in technological competition and to ensure sustainable business excellence. Most existing capability evaluation models utilize either quantitative methods, such as patent analysis, or qualitative methods, such as expert panels. Accordingly, they may be in danger of reflecting only fragmentary aspects of technological capabilities, and produce inconsistent results when different models are used. To solve these problems, this paper proposes a comprehensive framework for evaluating technological capabilities in energy companies by considering the complex properties of technological knowledge. For this purpose, we first explored various factors affecting technological capabilities and divided the factors into three categories: individual, organizational, and technology competitiveness. Second, we identified appropriate evaluation items for each category to measure the technological capability. Finally, by using a hybrid approach of qualitative and quantitative methods, we developed an evaluation method for each item and suggested a method to combine the results. The proposed framework was then verified with an energy generation and supply company to investigate its practicality. As one of the earliest attempts to evaluate multi-faceted technological capabilities, the suggested model can support technology and strategic planning.

Canadian national nuclear forensics capability project

International Nuclear Information System (INIS)

Ball, J.; Dimayuga, I.; Summerell, I.; Totland, M.; Jonkmans, G.; Whitlock, J.; El-jaby, A.; Inrig, E.

2015-01-01

Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

A Human Capabilities Framework for Evaluating Student Learning

Science.gov (United States)

Walker, Melanie

2008-01-01

This paper proposes a human capabilities approach for evaluating student learning and the social and pedagogical arrangements that support equality in capabilities for all students. It outlines the focus on valuable beings and doings in the capability approach developed by Amartya Sen, and Martha Nussbaum's capabilities focus on human flourishing.…

Assessment of macro and microelement accumulation capability of two aquatic plants

International Nuclear Information System (INIS)

Baldantoni, Daniela; Alfani, Anna; Di Tommasi, Paul; Bartoli, Giovanni; De Santo, Amalia Virzo

2004-01-01

The concentrations of four macroelements (C, N, P, S) and eight trace metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb, Zn) were measured in the leaves and roots of the emergent plant, Phragmites communis Trin., and in the shoots and roots of the submersed Najas marina L., taken from Lake Averno (Naples, Italy). Phragmites communis leaves showed higher concentrations of carbon, nitrogen and phosphorus than roots, while the roots exhibited significantly higher concentrations of sulphur and trace metals. Najas marina roots also showed higher concentrations of sulphur and trace metals than shoots, but these differences were less marked than in Phragmites communis except for sulphur. Sulphur was the only macronutrient to show the highest concentrations in the roots. Phragmites communis roots had higher values of Cr, Cu, Fe, Mn and Ni than Najas marina roots. By contrast, Cd, Cr, Fe, Ni, Pb and Zn concentrations were higher in Najas marina shoots than in Phragmites communis leaves. Phragmites communis, available through the year, showing high capability to accumulate trace metals in the roots, appears a good monitor of lake contamination, better than Najas marina. - Element accumulation in roots and shoots of aquatic plants was used as a criteria for selecting useful biomonitors

Spent fuel reprocessing system security engineering capability maturity model

International Nuclear Information System (INIS)

Liu Yachun; Zou Shuliang; Yang Xiaohua; Ouyang Zigen; Dai Jianyong

2011-01-01

In the field of nuclear safety, traditional work places extra emphasis on risk assessment related to technical skills, production operations, accident consequences through deterministic or probabilistic analysis, and on the basis of which risk management and control are implemented. However, high quality of product does not necessarily mean good safety quality, which implies a predictable degree of uniformity and dependability suited to the specific security needs. In this paper, we make use of the system security engineering - capability maturity model (SSE-CMM) in the field of spent fuel reprocessing, establish a spent fuel reprocessing systems security engineering capability maturity model (SFR-SSE-CMM). The base practices in the model are collected from the materials of the practice of the nuclear safety engineering, which represent the best security implementation activities, reflect the regular and basic work of the implementation of the security engineering in the spent fuel reprocessing plant, the general practices reveal the management, measurement and institutional characteristics of all process activities. The basic principles that should be followed in the course of implementation of safety engineering activities are indicated from 'what' and 'how' aspects. The model provides a standardized framework and evaluation system for the safety engineering of the spent fuel reprocessing system. As a supplement to traditional methods, this new assessment technique with property of repeatability and predictability with respect to cost, procedure and quality control, can make or improve the activities of security engineering to become a serial of mature, measurable and standard activities. (author)

Ensuring US National Aeronautics Test Capabilities

Science.gov (United States)

Marshall, Timothy J.

2010-01-01

U.S. leadership in aeronautics depends on ready access to technologically advanced, efficient, and affordable aeronautics test capabilities. These systems include major wind tunnels and propulsion test facilities and flight test capabilities. The federal government owns the majority of the major aeronautics test capabilities in the United States, primarily through the National Aeronautics and Space Administration (NASA) and the Department of Defense (DoD). However, changes in the Aerospace landscape, primarily the decrease in demand for testing over the last 20 years required an overarching strategy for management of these national assets. Therefore, NASA established the Aeronautics Test Program (ATP) as a two-pronged strategic initiative to: (1) retain and invest in NASA aeronautics test capabilities considered strategically important to the agency and the nation, and (2) establish a strong, high level partnership with the DoD. Test facility utilization is a critical factor for ATP because it relies on user occupancy fees to recover a substantial part of the operations costs for its facilities. Decreasing utilization is an indicator of excess capacity and in some cases low-risk redundancy (i.e., several facilities with basically the same capability and overall low utilization). However, low utilization does not necessarily translate to lack of strategic importance. Some facilities with relatively low utilization are nonetheless vitally important because of the unique nature of the capability and the foreseeable aeronautics testing needs. Unfortunately, since its inception, the customer base for ATP has continued to shrink. Utilization of ATP wind tunnels has declined by more than 50% from the FY 2006 levels. This significant decrease in customer usage is attributable to several factors, including the overall decline in new programs and projects in the aerospace sector; the impact of computational fluid dynamics (CFD) on the design, development, and research

Status Report on Modelling and Simulation Capabilities for Nuclear-Renewable Hybrid Energy Systems

Energy Technology Data Exchange (ETDEWEB)

Rabiti, C. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Epiney, A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Talbot, P. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Kim, J. S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Bragg-Sitton, S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Alfonsi, A. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Yigitoglu, A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Greenwood, S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Cetiner, S. M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ganda, F. [Argonne National Lab. (ANL), Argonne, IL (United States); Maronati, G. [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-09-01

This report summarizes the current status of the modeling and simulation capabilities developed for the economic assessment of Nuclear-Renewable Hybrid Energy Systems (N-R HES). The increasing penetration of variable renewables is altering the profile of the net demand, with which the other generators on the grid have to cope. N-R HES analyses are being conducted to determine the potential feasibility of mitigating the resultant volatility in the net electricity demand by adding industrial processes that utilize either thermal or electrical energy as stabilizing loads. This coordination of energy generators and users is proposed to mitigate the increase in electricity cost and cost volatility through the production of a saleable commodity. Overall, the financial performance of a system that is comprised of peaking units (i.e. gas turbine), baseload supply (i.e. nuclear power plant), and an industrial process (e.g. hydrogen plant) should be optimized under the constraint of satisfying an electricity demand profile with a certain level of variable renewable (wind) penetration. The optimization should entail both the sizing of the components/subsystems that comprise the system and the optimal dispatch strategy (output at any given moment in time from the different subsystems). Some of the capabilities here described have been reported separately in [1, 2, 3]. The purpose of this report is to provide an update on the improvement and extension of those capabilities and to illustrate their integrated application in the economic assessment of N-R HES.

Global dynamics, capabilities and the crisis

Czech Academy of Sciences Publication Activity Database

Fagerberg, J.; Srholec, Martin

2016-01-01

Roč. 26, č. 4 (2016), s. 765-784 ISSN 0936-9937 R&D Projects: GA ČR GAP402/10/2310 Institutional support: RVO:67985998 Keywords : technological capabilities * social capabilities * competitiveness Subject RIV: AH - Economics Impact factor: 0.862, year: 2016

Knowledge Perspectives on Advancing Dynamic Capability

NARCIS (Netherlands)

van Reijsen, J.

2014-01-01

Dynamic Capability is the organizational capacity to timely adapt to a changing market environment by reconfiguring resources and routines in order to stay competitive. Although dynamic capability is considered the Holy Grail of strategic management, a connection to the knowledge management domain

Canadian national nuclear forensics capability project

Energy Technology Data Exchange (ETDEWEB)

Ball, J.; Dimayuga, I., E-mail: joanne.ball@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Summerell, I. [Royal Canadian Mounted Police, Ottawa, Ontario (Canada); Totland, M. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Jonkmans, G. [Defence Research and Development Canada, Ottawa, Ontario (Canada); Whitlock, J. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); El-jaby, A. [Canadian Nuclear Safety Commission, Ottawa, Ontario (Canada); Inrig, E. [Defence Research and Development Canada, Ottawa, Ontario (Canada)

2015-06-15

Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

Building Airport Surface HITL Simulation Capability

Science.gov (United States)

Chinn, Fay Cherie

2016-01-01

FutureFlight Central is a high fidelity, real-time simulator designed to study surface operations and automation. As an air traffic control tower simulator, FFC allows stakeholders such as the FAA, controllers, pilots, airports, and airlines to develop and test advanced surface and terminal area concepts and automation including NextGen and beyond automation concepts and tools. These technologies will improve the safety, capacity and environmental issues facing the National Airspace system. FFC also has extensive video streaming capabilities, which combined with the 3-D database capability makes the facility ideal for any research needing an immersive virtual and or video environment. FutureFlight Central allows human in the loop testing which accommodates human interactions and errors giving a more complete picture than fast time simulations. This presentation describes FFCs capabilities and the components necessary to build an airport surface human in the loop simulation capability.

Developmental Course of Impulsivity and Capability from Age 10 to Age 25 as Related to Trajectory of Suicide Attempt in a Community Cohort

OpenAIRE

Kasen, Stephanie; Cohen, Patricia; Chen, Henian

2011-01-01

Hierarchical linear models were used to examine trajectories of impulsivity and capability between ages 10 and 25 in relation to suicide attempt in 770 youths followed longitudinally: intercepts were set at age 17. The impulsivity measure assessed features of urgency (e.g., poor control, quick provocation, and disregard for external constraints); the capability measure assessed aspects of self-esteem and mastery. Compared to nonattempters, attempters reported significantly higher impulsivity ...

The Atmospheric Release Advisory Capability Site Workstation System

International Nuclear Information System (INIS)

Foster, K.T.; Sumikawa, D.A.; Foster, C.S.; Baskett, R.L.

1993-01-01

The Atmospheric Release Advisory Capability (ARAC) is a centralized emergency response service that assesses the consequences that may result from an atmospheric release of toxic material. ARAC was developed by the Lawrence Livermore National Laboratory (LLNL) for the Departments of Energy (DOE) and Defense (DOD) and responds principally to radiological accidents. ARAC provides radiological health and safety guidance to decision makers in the form of computer-generated estimates of the effects of an actual, or potential release of radioactive material into the atmosphere. Upon receipt of the release scenario, the ARAC assessment staff extracts meteorological, topographic, and geographic data from resident world-wide databases for use in complex, three-dimensional transport and diffusion models. These dispersion models generate air concentration (or dose) and ground deposition contour plots showing estimates of the contamination patterns produced as the toxic material is carried by the prevailing winds. To facilitate the ARAC response to a release from specific DOE and DOD sites and to provide these sites with a local emergency response tool, a remote Site Workstation System (SWS) is being placed at various ARAC-supported facilities across the country.. This SWS replaces the existing antiquated ARAC Site System now installed at many of these sites. The new system gives users access to complex atmospheric dispersion models that may be run either by the ARAC staff at LLNL, or (in a later phase of the system) by site personnel using the computational resources of the SWS. Supporting this primary function are a variety of SWS-resident supplemental capabilities that include meteorological data acquisition, manipulation of release-specific databases, computer-based communications, and the use of a simpler Gaussian trajectory puff model that is based on Environmental Protection Agency's INPUFF code

Networking capability and new product development

NARCIS (Netherlands)

Mu, J.; Di Benedetto, A.C.

2012-01-01

Current research on network theory remains largely focused on structures and outcomes without exploring the capability that firms need to build efficient and effective networks to their advantage. In this paper, we take a networking capability view in studying inter-firm relationships. We assume

Current Capability of Atomic Structure Theory

International Nuclear Information System (INIS)

Kim, Yong Ki

1993-01-01

Current capability of atomic structure theory is reviewed, and advantages, disadvantages and major features of popular atomic structure codes described. Comparisons between theoretical and experimental data on transition energies and lifetimes of excited levels are presented to illustrate the current capability of atomic structure codes.

Severe accident management (SAM), operator training and instrumentation capabilities - Summary and conclusions

International Nuclear Information System (INIS)

2002-01-01

The Workshop on Operator Training for Severe Accident Management (SAM) and Instrumentation Capabilities During Severe Accidents was organised in collaboration with Electricite de France (Service Etudes et Projets Thermiques et Nucleaires). There were 34 participants, representing thirteen OECD Member countries, the Russian Federation and the OECD/NEA. Almost half the participants represented utilities. The second largest group was regulatory authorities and their technical support organisations. Basically, the Workshop was a follow-up to the 1997 Second Specialist Meeting on Operator Aids for Severe Accident Management (SAMOA-2) [Reports NEA/CSNI/R(97)10 and 27] and to the 1992 Specialist Meeting on Instrumentation to Manage Severe Accidents [Reports NEA/CSNI/R(92)11 and (93)3]. It was aimed at sharing and comparing progress made and experience gained from these two meetings, emphasizing practical lessons learnt during training or incidents as well as feedback from instrumentation capability assessment. The objectives of the Workshop were therefore: - to exchange information on recent and current activities in the area of operator training for SAM, and lessons learnt during the management of real incidents ('operator' is defined hear as all personnel involved in SAM); - to compare capabilities and use of instrumentation available during severe accidents; - to monitor progress made; - to identify and discuss differences between approaches relevant to reactor safety; - and to make recommendations to the Working Group on the Analysis and Management of Accidents and the CSNI (GAMA). The Workshop was organised into five sessions: - 1: Introduction; - 2: Tools and Methods; - 3: Training Programmes and Experience; - 4: SAM Organisation Efficiency; - 5: Instrumentation Capabilities. It was concluded by a Panel and General Discussion. This report presents the summary and conclusions: the meeting confirmed that only limited information is needed for making required decisions

Exploration Medical Capability (ExMC) Projects

Science.gov (United States)

Wu, Jimmy; Watkins, Sharmila; Baumann, David

2010-01-01

During missions to the Moon or Mars, the crew will need medical capabilities to diagnose and treat disease as well as for maintaining their health. The Exploration Medical Capability Element develops medical technologies, medical informatics, and clinical capabilities for different levels of care during space missions. The work done by team members in this Element is leading edge technology, procedure, and pharmacological development. They develop data systems that protect patient's private medical information, aid in the diagnosis of medical conditions, and act as a repository of relevant NASA life sciences experimental studies. To minimize the medical risks to crew health the physicians and scientists in this Element develop models to quantify the probability of medical events occurring during a mission. They define procedures to treat an ill or injured crew member who does not have access to an emergency room and who must be cared for in a microgravity environment where both liquids and solids behave differently than on Earth. To support the development of these medical capabilities, the Element manages the development of medical technologies that prevent, monitor, diagnose, and treat an ill or injured crewmember. The Exploration Medical Capability Element collaborates with the National Space Biomedical Research Institute (NSBRI), the Department of Defense, other Government-funded agencies, academic institutions, and industry.

Computational physics and applied mathematics capability review June 8-10, 2010

Energy Technology Data Exchange (ETDEWEB)

Lee, Stephen R [Los Alamos National Laboratory

2010-01-01

Los Alamos National Laboratory will review its Computational Physics and Applied Mathematics (CPAM) capabilities in 2010. The goals of capability reviews are to assess the quality of science, technology, and engineering (STE) performed by the capability, evaluate the integration of this capability across the Laboratory and within the scientific community, examine the relevance of this capability to the Laboratory's programs, and provide advice on the current and future directions of this capability. This is the first such review for CPAM, which has a long and unique history at the Laboratory, starting from the inception of the Laboratory in 1943. The CPAM capability covers an extremely broad technical area at Los Alamos, encompassing a wide array of disciplines, research topics, and organizations. A vast array of technical disciplines and activities are included in this capability, from general numerical modeling, to coupled multi-physics simulations, to detailed domain science activities in mathematics, methods, and algorithms. The CPAM capability involves over 12 different technical divisions and a majority of our programmatic and scientific activities. To make this large scope tractable, the CPAM capability is broken into the following six technical 'themes.' These themes represent technical slices through the CPAM capability and collect critical core competencies of the Laboratory, each of which contributes to the capability (and each of which is divided into multiple additional elements in the detailed descriptions of the themes in subsequent sections), as follows. Theme 1: Computational Fluid Dynamics - This theme speaks to the vast array of scientific capabilities for the simulation of fluids under shocks, low-speed flow, and turbulent conditions - which are key, historical, and fundamental strengths of the Laboratory. Theme 2: Partial Differential Equations - The technical scope of this theme is the applied mathematics and numerical solution

THE EFFECTS OF GLYCATION ON THE BINDING OF HUMAN SERUM ALBUMIN TO WARFARIN AND L-TRYPTOPHAN

OpenAIRE

Joseph, K.S.; Hage, David S.

2010-01-01

Diabetes leads to elevated levels of glucose in blood which, in turn, can lead to the non-enzymatic glycation of serum proteins such as human serum albumin (HSA). It has been suggested that this increase in glycation can alter the ability of HSA to bind to drugs and other small solutes. This study used high-performance affinity chromatography (HPAC) to see if there is any significant change related to glycation in the binding of HSA to warfarin and L-tryptophan, which are often used as probe ...

The Capability Approach

NARCIS (Netherlands)

I.A.M. Robeyns (Ingrid)

2011-01-01

textabstract In its most general description, the capability approach is a flexible and multi-purpose normative framework, rather than a precise theory of well-being, freedom or justice. At its core are two normative claims: first, the claim that the freedom to achieve well-being is of primary

Petroleum system modeling capabilities for use in oil and gas resource assessments

Science.gov (United States)

Higley, Debra K.; Lewan, Michael; Roberts, Laura N.R.; Henry, Mitchell E.

2006-01-01

Summary: Petroleum resource assessments are among the most highly visible and frequently cited scientific products of the U.S. Geological Survey. The assessments integrate diverse and extensive information on the geologic, geochemical, and petroleum production histories of provinces and regions of the United States and the World. Petroleum systems modeling incorporates these geoscience data in ways that strengthen the assessment process and results are presented visually and numerically. The purpose of this report is to outline the requirements, advantages, and limitations of one-dimensional (1-D), two-dimensional (2-D), and three-dimensional (3-D) petroleum systems modeling that can be applied to the assessment of oil and gas resources. Primary focus is on the application of the Integrated Exploration Systems (IES) PetroMod? software because of familiarity with that program as well as the emphasis by the USGS Energy Program on standardizing to one modeling application. The Western Canada Sedimentary Basin (WCSB) is used to demonstrate the use of the PetroMod? software. Petroleum systems modeling quantitatively extends the 'total petroleum systems' (TPS) concept (Magoon and Dow, 1994; Magoon and Schmoker, 2000) that is employed in USGS resource assessments. Modeling allows integration of state-of-the-art analysis techniques, and provides the means to test and refine understanding of oil and gas generation, migration, and accumulation. Results of modeling are presented visually, numerically, and statistically, which enhances interpretation of the processes that affect TPSs through time. Modeling also provides a framework for the input and processing of many kinds of data essential in resource assessment, including (1) petroleum system elements such as reservoir, seal, and source rock intervals; (2) timing of depositional, hiatus, and erosional events and their influences on petroleum systems; (3) incorporation of vertical and lateral distribution and lithologies of

Functional capability of piping systems

International Nuclear Information System (INIS)

Terao, D.; Rodabaugh, E.C.

1992-11-01

General Design Criterion I of Appendix A to Part 50 of Title 10 of the Code of Federal Regulations requires, in part, that structures, systems, and components important to safety be designed to withstand the effects of earthquakes without a loss of capability to perform their safety function. ne function of a piping system is to convey fluids from one location to another. The functional capability of a piping system might be lost if, for example, the cross-sectional flow area of the pipe were deformed to such an extent that the required flow through the pipe would be restricted. The objective of this report is to examine the present rules in the American Society of Mechanical Engineers Boiler and Pressure Vessel Code, Section III, and potential changes to these rules, to determine if they are adequate for ensuring the functional capability of safety-related piping systems in nuclear power plants

Upgrading of TREAT experimental capabilities

International Nuclear Information System (INIS)

Dickerman, C.E.; Rose, D.; Bhattacharyya, S.K.

1982-01-01

The TREAT facility at the Argonne National Laboratory site in the Idaho National Engineering Laboratory is being upgraded to provide capabilities for fast-reactor-safety transient experiments not possible at any other experimental facility. Principal TREAT Upgrade (TU) goal is provision for 37-pin size experiments on energetics of core-disruptive accidents (CDA) in fast breeder reactor cores with moderate sodium void coefficients. this goal requires a significant enhancement of the capabilities of the TREAT facility, specifically including reactor control, hardened neutron spectrum incident on the test sample, and enlarged building. The upgraded facility will retain the capability for small-size experiments of the types currently being performed in TREAT. Reactor building and crane upgrading have been completed. TU schedules call for the components of the upgraded reactor system to be finished in 1984, including upgraded TREAT fuel and control system, and expanded coverage by the hodoscope fuel-motion diagnostics system

Kokkos' Task DAG Capabilities.

Energy Technology Data Exchange (ETDEWEB)

Edwards, Harold C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Ibanez, Daniel Alejandro [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-09-01

This report documents the ASC/ATDM Kokkos deliverable "Production Portable Dy- namic Task DAG Capability." This capability enables applications to create and execute a dynamic task DAG ; a collection of heterogeneous computational tasks with a directed acyclic graph (DAG) of "execute after" dependencies where tasks and their dependencies are dynamically created and destroyed as tasks execute. The Kokkos task scheduler executes the dynamic task DAG on the target execution resource; e.g. a multicore CPU, a manycore CPU such as Intel's Knights Landing (KNL), or an NVIDIA GPU. Several major technical challenges had to be addressed during development of Kokkos' Task DAG capability: (1) portability to a GPU with it's simplified hardware and micro- runtime, (2) thread-scalable memory allocation and deallocation from a bounded pool of memory, (3) thread-scalable scheduler for dynamic task DAG, (4) usability by applications.

Adult Financial Capability Framework. Second Edition

Science.gov (United States)

Basic Skills Agency, 2006

2006-01-01

Both the Financial Services Authority and the Basic Skills Agency are committed to supporting those individuals and organisations working to improve the financial capability of themselves and others. The development of the National Strategy for Financial Capability, coordinated by the Financial Services Authority, and the commissioning of a…

CloudSat-Based Assessment of GPM Microwave Imager Snowfall Observation Capabilities

Directory of Open Access Journals (Sweden)

Giulia Panegrossi

2017-12-01

Full Text Available The sensitivity of Global Precipitation Measurement (GPM Microwave Imager (GMI high-frequency channels to snowfall at higher latitudes (around 60°N/S is investigated using coincident CloudSat observations. The 166 GHz channel is highlighted throughout the study due to its ice scattering sensitivity and polarization information. The analysis of three case studies evidences the important combined role of total precipitable water (TPW, supercooled cloud water, and background surface composition on the brightness temperature (TB behavior for different snow-producing clouds. A regression tree statistical analysis applied to the entire GMI-CloudSat snowfall dataset indicates which variables influence the 166 GHz polarization difference (166 ∆TB and its relation to snowfall. Critical thresholds of various parameters (sea ice concentration (SIC, TPW, ice water path (IWP are established for optimal snowfall detection capabilities. The 166 ∆TB can identify snowfall events over land and sea when critical thresholds are exceeded (TPW > 3.6 kg·m−2, IWP > 0.24 kg·m−2 over land, and SIC > 57%, TPW > 5.1 kg·m−2 over sea. The complex combined 166 ∆TB-TB relationship at higher latitudes and the impact of supercooled water vertical distribution are also investigated. The findings presented in this study can be exploited to improve passive microwave snowfall detection algorithms.

Business Undergraduates' Perceptions of Their Capabilities in Employability Skills: Implications for Industry and Higher Education

Science.gov (United States)

Jackson, Denise

2012-01-01

In response to the continuing disparity between industry expectations and higher education provision, this study examines the self-assessed capabilities of 1,024 business undergraduates in employability skills typically considered important by industry in developed economies. The findings indicate relative perceived strengths in "social…

Canadian oil spill response capability - an investigation of the proposed fee regime

International Nuclear Information System (INIS)

Gold, E.; Gratwick, J.; Yee, P.

1996-08-01

Canada's oil spill response capability and its fee structure was examined and assessed. The present regime consists of five industry-owned oil spill response organizations who provide response teams throughout Canadian waters, except the Arctic. These organizations are fully adequate to meet the standards set by the Canadian Coast Guard. However, the Canadian Coast Guard withdrew from active control of the fee regime, leaving it to each response team to determine its own fee structure. The expectation was that the market would be capable of controlling the fees to be charged. This did not happen, and the investigative panel came to the conclusion that the present regime was not workable. In view of the situation the Panel concluded that ensuring oil spill response capability in Canada must always be the sole responsibility of the Canadian Government. Eleven recommendations were detailed in this final report. The most important recommendation was that the Canadian Coast Guard should re-establish its principal role in the oil spill response area. It was also suggested that there should be a single, national fee structure applying to the whole country except the Arctic, and that the fee should be collected by an independent national agency

Making Capability Lists: Philosophy versus Democracy

NARCIS (Netherlands)

Claassen, R.J.G.

2011-01-01

The article discusses a fundamental problem that has to be faced if the general capability approach is to be developed in the direction of a theory of justice: the selection and justification of a list of capabilities. The democratic solution to this problem (defended by Amartya Sen) is to leave the

Preliminary analysis of the postulated changes needed to achieve rail cask handling capabilities at selected light water reactors

International Nuclear Information System (INIS)

Konzek, G.J.

1986-02-01

Reactor-specific railroad and crane information for all LWRs in the US was extracted from current sources of information. Based on this information, reactors were separated into two basic groups consisting of reactors with existing, usable rail cask capabilities and those without these capabilities. The latter group is the main focus of this study. The group of reactors without present rail cask handling capabilities was further separated into two subgroups consisting of reactors considered essentially incapable of handling a large rail cask of about 100 tons and reactors where postulated facility changes could result in rail cask handling capabilities. Based on a selected population of 127 reactors, the results of this assessment indicate that usable rail cask capabilities exist at 83 (65%) of the reactors. Twelve (27%) of the remaining 44 reactors are deemed incapable of handling a large rail cask without major changes, and 32 reactors are considered likely candidates for potentially achieving rail cask handling capabilities. In the latter group, facility changes were postulated that would conceptually enable these reactors to handle large rail casks. The estimated cost per plant of required facility changes varied widely from a high of about $35 million to a low of <$0.3 million. Only 11 of the 32 plants would require crane upgrades. Spur track and right-of-way costs would apparently vary widely among sites. These results are based on preliminary analyses using available generic cost data. They represent lower bound values that are useful for developing an initial assessment of the viability of the postulated changes on a system-wide basis, but are not intended to be absolute values for specific reactors or sites

A Value Based Justification Process for Aerospace RDT and E Capability Investments

Science.gov (United States)

2017-12-01

Hypersonics Division (Tunnel 9), 10905 New Hampshire Ave. (AIAA Associate Fellow) 3 Senior Engineering Specialist, Jacobs Tidewater Operations Group , (AIAA...typically involves the same group of SMEs that supported the key capability needs analysis. Each SME is also asked to provide a high/medium/low assessment as...be developed. Further, the assistance and counsel of SMEs with access to such information and data is essential. This is vital to the successful

Physician capability to electronically exchange clinical information, 2011.

Science.gov (United States)

Patel, Vaishali; Swain, Matthew J; King, Jennifer; Furukawa, Michael F

2013-10-01

To provide national estimates of physician capability to electronically share clinical information with other providers and to describe variation in exchange capability across states and electronic health record (EHR) vendors using the 2011 National Ambulatory Medical Care Survey Electronic Medical Record Supplement. Survey of a nationally representative sample of nonfederal office-based physicians who provide direct patient care. The survey was administered by mail with telephone follow-up and had a 61% weighted response rate. The overall sample consisted of 4326 respondents. We calculated estimates of electronic exchange capability at the national and state levels, and applied multivariate analyses to examine the association between the capability to exchange different types of clinical information and physician and practice characteristics. In 2011, 55% of physicians had computerized capability to send prescriptions electronically; 67% had the capability to view lab results electronically; 42% were able to incorporate lab results into their EHR; 35% were able to send lab orders electronically; and, 31% exchanged patient clinical summaries with other providers. The strongest predictor of exchange capability is adoption of an EHR. However, substantial variation exists across geography and EHR vendors in exchange capability, especially electronic exchange of clinical summaries. In 2011, a majority of office-based physicians could exchange lab and medication data, and approximately one-third could exchange clinical summaries with patients or other providers. EHRs serve as a key mechanism by which physicians can exchange clinical data, though physicians' capability to exchange varies by vendor and by state.

Methods of ecological capability evaluation of forest

International Nuclear Information System (INIS)

Hosseini, M.; Makhdoum, M.F.; Akbarnia, M.; Saghebtalebi, Kh.

2000-01-01

In this research common methods of ecological capability evaluation of forests were reviewed and limitations for performance were analysed. Ecological capability of forests is an index that show site potential in several role of wood production, soil conservation, flood control, biodiversity, conservation and water supply. This index is related to ecological characteristics of land, such as soil, micro climate, elevation, slope and aspect that affect potential of sites. Suitable method of ecological capability evaluation must be chosen according to the objective of forestry. Common methods for ecological capability evaluation include plant and animal diversity, site index curve, soil and land form, inter branches, index plants, leave analyses, analyses regeneration and ecological mapping

Land Capability Evaluation of Upper Sekampung Watersheds

Directory of Open Access Journals (Sweden)

Irwan Sukri Banuwa

2008-05-01

Full Text Available Land degradation is a serious problem in the Upper Sekampung Watersheds. This is because the farmers cultivated in steep land to coffee crops without in adequate soil and water conservation practices. The land degradation is mostly caused by erosion. The erosion problem not only stripping the most fertile top soil and decreasing crop production, but also resulting problems in lowland. Therefore, the reorientation land management should be improved to produce agriculture sustainability. The first step is to evaluated land capability this area. The objectives of the research were evaluate land capability of Upper Sekampung Watersheds. The results showed that the Upper Sekampung Watersheds were dominated with class and subclass land capability of III-l2 about 17.630,51 ha (41,58%. All of the constrain for each land capability in this area is erosion hazard, especially land slope. From this research, cultivated land to coffee base crops were allowed in land capability II-l1.e1, III-l2, IV-l3, and VI-l4, with in adequate soil and water conservation practices. In contrary, the land capability of VII-l5 unsuitable for agriculture, they should be a nature or for conservation forest.

Technological Capability and Firm Performance

Directory of Open Access Journals (Sweden)

Fernanda Maciel Reichert

2014-08-01

Full Text Available This research aims to investigate the relationship between investments in technological capability and economic performance in Brazilian firms. Based on economic development theory and on developed countries history, it is assumed that this relationship is positive. Through key indicators, 133 Brazilian firms have been analyzed. Given the economic circumstances of an emerging economy, which the majority of businesses are primarily based on low and medium-low-technology industries, it is not possible to affirm the existence of a positive relation between technological capability and firm performance. There are other elements that allow firms to achieve such results. Firms of lower technological intensity industries performed above average in the economic performance indicators, adversely, they invested below average in technological capability. These findings do not diminish the merit of firms’ and country’s success. They in fact confirm a historical tradition of a country that concentrates its efforts on basic industries.

Domestic uranium mining and milling industry: 1986 viability assessment

International Nuclear Information System (INIS)

1987-01-01

This report presents the fourth annual assessment of the domestic uranium mining and milling industry's resource capability, supply response capability, financial capability, and import commitment dependency. The data and analysis in support of this assessment and the report itself have been developed pursuant to Public Law 97-415, the Nuclear Regulatory Commission (NRC) Authorization Act of 1982. The report provides information on recent uranium supply, demand, and marketing conditions, as well as projections of the domestic uranium industry's ability to continue to supply the needs of the domestic nuclear power industry through the year 2000. Industry capability is assessed under a variety of assumed conditions with respect to hypothetical disruptions of uranium imports. 13 refs., 26 figs., 37 tabs

Human-Centered Design Capability

Science.gov (United States)

Fitts, David J.; Howard, Robert

2009-01-01

For NASA, human-centered design (HCD) seeks opportunities to mitigate the challenges of living and working in space in order to enhance human productivity and well-being. Direct design participation during the development stage is difficult, however, during project formulation, a HCD approach can lead to better more cost-effective products. HCD can also help a program enter the development stage with a clear vision for product acquisition. HCD tools for clarifying design intent are listed. To infuse HCD into the spaceflight lifecycle the Space and Life Sciences Directorate developed the Habitability Design Center. The Center has collaborated successfully with program and project design teams and with JSC's Engineering Directorate. This presentation discusses HCD capabilities and depicts the Center's design examples and capabilities.

Using Porterian Activity Analysis to Understand Organizational Capabilities

DEFF Research Database (Denmark)

Sheehan, Norman T.; Foss, Nicolai Juul

2017-01-01

conceptualized by Porter’s writings on the activity-based view. Porterian activity analysis is becoming more accepted in the strategy literature, but no strategy scholar has explicitly used Porter’s activities, and particularly his concept of drivers, to understand and analyze organizational capabilities....... Introducing Porterian activities into the discussion of capabilities improves strategy scholars’ understanding of the bases of capability heterogeneity, offers academics future directions for research, and provides managers with guidance to enhance their organizations’ capabilities....

Evidence for Endothermy in Pterosaurs Based on Flight Capability Analyses

Science.gov (United States)

Jenkins, H. S.; Pratson, L. F.

2005-12-01

Previous attempts to constrain flight capability in pterosaurs have relied heavily on the fossil record, using bone articulation and apparent muscle allocation to evaluate flight potential (Frey et al., 1997; Padian, 1983; Bramwell, 1974). However, broad definitions of the physical parameters necessary for flight in pterosaurs remain loosely defined and few systematic approaches to constraining flight capability have been synthesized (Templin, 2000; Padian, 1983). Here we present a new method to assess flight capability in pterosaurs as a function of humerus length and flight velocity. By creating an energy-balance model to evaluate the power required for flight against the power available to the animal, we derive a `U'-shaped power curve and infer optimal flight speeds and maximal wingspan lengths for pterosaurs Quetzalcoatlus northropi and Pteranodon ingens. Our model corroborates empirically derived power curves for the modern black-billed magpie ( Pica Pica) and accurately reproduces the mechanical power curve for modern cockatiels ( Nymphicus hollandicus) (Tobalske et al., 2003). When we adjust our model to include an endothermic metabolic rate for pterosaurs, we find a maximal wingspan length of 18 meters for Q. northropi. Model runs using an exothermic metabolism derive maximal wingspans of 6-8 meters. As estimates based on fossil evidence show total wingspan lengths reaching up to 15 meters for Q. northropi, we conclude that large pterosaurs may have been endothermic and therefore more metabolically similar to birds than to reptiles.

Downregulation of tight junction-associated MARVEL protein marvelD3 during epithelial-mesenchymal transition in human pancreatic cancer cells.

Science.gov (United States)

Kojima, Takashi; Takasawa, Akira; Kyuno, Daisuke; Ito, Tatsuya; Yamaguchi, Hiroshi; Hirata, Koichi; Tsujiwaki, Mitsuhiro; Murata, Masaki; Tanaka, Satoshi; Sawada, Norimasa

2011-10-01

The novel tight junction protein marvelD3 contains a conserved MARVEL (MAL and related proteins for vesicle trafficking and membrane link) domain like occludin and tricellulin. However, little is yet known about the detailed role and regulation of marvelD3 in normal epithelial cells and cancer cells, including pancreatic cancer. In the present study, we investigated marvelD3 expression in well and poorly differentiated human pancreatic cancer cell lines and normal pancreatic duct epithelial cells in which the hTERT gene was introduced into human pancreatic duct epithelial cells in primary culture, and the changes of marvelD3 during Snail-induced epithelial-mesenchymal transition (EMT) under hypoxia, TGF-β treatment and knockdown of FOXA2 in well differentiated pancreatic cancer HPAC cells. MarvelD3 was transcriptionally downregulated in poorly differentiated pancreatic cancer cells and during Snail-induced EMT of pancreatic cancer cells in which Snail was highly expressed and the fence function downregulated, whereas it was maintained in well differentiated human pancreatic cancer cells and normal pancreatic duct epithelial cells. Depletion of marvelD3 by siRNAs in HPAC cells resulted in downregulation of barrier functions indicated as a decrease in transepithelial electric resistance and an increase of permeability to fluorescent dextran tracers, whereas it did not affect fence function of tight junctions. In conclusion, marvelD3 is transcriptionally downregulated in Snail-induced EMT during the progression for the pancreatic cancer. Copyright © 2011 Elsevier Inc. All rights reserved.

Analysis of the performance capability of an infrared interior intrusion detector

International Nuclear Information System (INIS)

Dunn, D.R.

1977-01-01

Component performances are required by the LLL assessment procedure for material control and accounting (MC and A) systems. Monitors are an example of an MC and A component whose functions are to process measurements or observations for purposes of detecting abnormalities. This report develops a methodology for characterizing the performance of a class of infrared (IR) interior intrusion monitors or detectors. The methodology is developed around a specific commercial IR detector, the InfrAlarm, manufactured by Barnes Engineering Company (Models 19-124 and 19-115A). Statistical detection models for computing probabilities of detection and false alarms were derived, and the performance capability of the InfrAlarm IR detector was shown using these measures. The results obtained in the performance analysis show that the detection capability of the InfrAlarm is excellent (approx. 1), with very low false alarm rates, for a wide range in target characteristics. These results should be representative and particularly for non-hostile environments

Land Capability Potential Index (LCPI) and geodatabase for the Lower Missouri River Valley

Science.gov (United States)

Chojnacki, Kimberly A.; Struckhoff, Matthew A.; Jacobson, Robert B.

2012-01-01

The Land Capacity Potential Index (LCPI) is a coarse-scale index intended to delineate broad land-capability classes in the Lower Missouri River valley bottom from the Gavins Point Dam near Yankton, South Dakota to the mouth of the Missouri River near St. Louis, Missouri (river miles 811–0). The LCPI provides a systematic index of wetness potential and soil moisture-retention potential of the valley-bottom lands by combining the interactions among water-surface elevations, land-surface elevations, and the inherent moisture-retention capability of soils. A nine-class wetness index was generated by intersecting a digital elevation model for the valley bottom with sloping water-surface elevation planes derived from eight modeled discharges. The flow-recurrence index was then intersected with eight soil-drainage classes assigned to soils units in the digital Soil Survey Geographic (SSURGO) Database (Soil Survey Staff, 2010) to create a 72-class index of potential flow-recurrence and moisture-retention capability of Missouri River valley-bottom lands. The LCPI integrates the fundamental abiotic factors that determine long-term suitability of land for various uses, particularly those relating to vegetative communities and their associated values. Therefore, the LCPI provides a mechanism allowing planners, land managers, landowners, and other stakeholders to assess land-use capability based on the physical properties of the land, in order to guide future land-management decisions. This report documents data compilation for the LCPI in a revised and expanded, 72-class version for the Lower Missouri River valley bottom, and inclusion of additional soil attributes to allow users flexibility in exploring land capabilities.

78 FR 20219 - National Financial Capability Month, 2013

Science.gov (United States)

2013-04-04

... requires smart financial planning. During National Financial Capability Month, we recommit to empowering... Financial Capability Month, 2013 By the President of the United States of America A Proclamation All... financial literacy. We released a new financial capability toolkit to help schools and employers as they...

Environmental and emergency response capabilities of Los Alamos Scientific Laboratory's radiological air sampling program

International Nuclear Information System (INIS)

Gunderson, T.C.

1980-05-01

Environmental and emergency response radiological air sampling capabilities of the Environmental Surveillance Group at Los Alamos Scientific Laboratory are described. The air sampling program provides a supplementary check on the adequacy of containment and effluent controls, determines compliance with applicable protection guides and standards, and assesses potential environmental impacts on site environs. It also allows evaluation of potential individual and total population doses from airborne radionuclides that may be inhaled or serve as a source of external radiation. The environmental program is sufficient in scope to detect fluctuations and long-term trends in atmospheric levels of radioactivity originating onsite. The emergency response capabilities are designed to respond to both onsite unplanned releases and atmospheric nuclear tests

Space Communications Capability Roadmap Interim Review

Science.gov (United States)

Spearing, Robert; Regan, Michael

2005-01-01

Contents include the following: Identify the need for a robust communications and navigation architecture for the success of exploration and science missions. Describe an approach for specifying architecture alternatives and analyzing them. Establish a top level architecture based on a network of networks. Identify key enabling technologies. Synthesize capability, architecture and technology into an initial capability roadmap.

Engineering Capabilities and Partnerships

Science.gov (United States)

Poulos, Steve

2010-01-01

This slide presentation reviews the engineering capabilities at Johnson Space Center, The presentation also reviews the partnerships that have resulted in successfully designed and developed projects that involved commercial and educational institutions.

Moving interprofessional learning forward through formal assessment.

Science.gov (United States)

Stone, Judy

2010-04-01

There is increasing agreement that graduates who finish tertiary education with the full complement of skills and knowledge required for their designated profession are not 'work-ready' unless they also acquire interpersonal, collaborative practice and team-working capabilities. Health workers are unable to contribute to organisational culture in a positive way unless they too attain these capabilities. These capabilities have been shown to improve health care in terms of patient safety, worker satisfaction and health service efficiency. Given the importance of interprofessional learning (IPL) which seeks to address these capabilities, why is IPL not consistently embedded into the education of undergraduates, postgraduates and vocationally qualified personnel through formal assessment? This paper offers an argument for the formal assessment of IPL. It illustrates how the interests of the many stakeholders in IPL can benefit from, and contribute to, the integration of IPL into mainstream professional development and tertiary education. It offers practical examples of assessment in IPL which could drive learning and offer authentic, contextual teaching and learning experiences to undergraduates and health workers alike. Assessment drives learning and without formal assessment IPL will continue to be viewed as an optional topic of little relative importance for learners. In order to make the next step forward, IPL needs to be recognised and endorsed through formal assessment, both at the tertiary education level and within the workplace environment. This is supported by workforce initiatives and tertiary education policy which can be used to specify the capabilities or generic skills necessary for effective teamwork and collaborative practice.

NASA Stennis Space Center Integrated System Health Management Test Bed and Development Capabilities

Science.gov (United States)

Figueroa, Fernando; Holland, Randy; Coote, David

2006-01-01

Integrated System Health Management (ISHM) is a capability that focuses on determining the condition (health) of every element in a complex System (detect anomalies, diagnose causes, prognosis of future anomalies), and provide data, information, and knowledge (DIaK)-not just data-to control systems for safe and effective operation. This capability is currently done by large teams of people, primarily from ground, but needs to be embedded on-board systems to a higher degree to enable NASA's new Exploration Mission (long term travel and stay in space), while increasing safety and decreasing life cycle costs of spacecraft (vehicles; platforms; bases or outposts; and ground test, launch, and processing operations). The topics related to this capability include: 1) ISHM Related News Articles; 2) ISHM Vision For Exploration; 3) Layers Representing How ISHM is Currently Performed; 4) ISHM Testbeds & Prototypes at NASA SSC; 5) ISHM Functional Capability Level (FCL); 6) ISHM Functional Capability Level (FCL) and Technology Readiness Level (TRL); 7) Core Elements: Capabilities Needed; 8) Core Elements; 9) Open Systems Architecture for Condition-Based Maintenance (OSA-CBM); 10) Core Elements: Architecture, taxonomy, and ontology (ATO) for DIaK management; 11) Core Elements: ATO for DIaK Management; 12) ISHM Architecture Physical Implementation; 13) Core Elements: Standards; 14) Systematic Implementation; 15) Sketch of Work Phasing; 16) Interrelationship Between Traditional Avionics Systems, Time Critical ISHM and Advanced ISHM; 17) Testbeds and On-Board ISHM; 18) Testbed Requirements: RETS AND ISS; 19) Sustainable Development and Validation Process; 20) Development of on-board ISHM; 21) Taxonomy/Ontology of Object Oriented Implementation; 22) ISHM Capability on the E1 Test Stand Hydraulic System; 23) Define Relationships to Embed Intelligence; 24) Intelligent Elements Physical and Virtual; 25) ISHM Testbeds and Prototypes at SSC Current Implementations; 26) Trailer

Daugherty Memorial Assessment Center (DMAC)

Data.gov (United States)

Federal Laboratory Consortium — Daugherty Memorial Assessment Center (DMAC) is a 39,000-square-foot facility that doubles the warfare center's high-secured performance assessment capabilities. DMAC...

Tsunami disaster risk management capabilities in Greece

Science.gov (United States)

Marios Karagiannis, Georgios; Synolakis, Costas

2015-04-01

System, with the Greek NWTC actively participating as a Candidate Tsunami Watch Provider. In addition, Greece designed and conducted the first tsunami exercise program in the Union Civil Protection Mechanism in 2011, which also considered the attrition of response capabilities by the earthquake generating the tsunami. These exercises have demonstrated the capability of the Greek NWTC to provide early warning to local civil protection authorities, but warning dissemination to the population remains an issue, especially during the summer season. However, there is no earthquake or tsunami national emergency operations plan, and we found that tsunami disaster planning and preparedness activities are rather limited at the local level. We acknowledge partial support by the project ASTARTE (Assessment, STrategy And Risk Reduction for Tsunamis in Europe) FP7-ENV2013 6.4-3, Grant 603839 to the Technical University of Crete.

A JOINT VENTURE MODEL FOR ASSESSMENT OF PARTNER CAPABILITIES: THE CASE OF ESKOM ENTERPRISES AND THE AFRICAN POWER SECTOR

Directory of Open Access Journals (Sweden)

Y.V. Soni

2012-01-01

Full Text Available

ENGLISH ABSTRACT: This article investigates the concept of joint ventures in the international energy sector and develops a joint venture model, as a business development and assessment tool. The joint venture model presents a systematic method that relies on modern business intelligence to assess a potential business venture by using a balanced score card technique to screen potential partners, based on their technological and financial core capabilities. The model can be used by business development managers to harness the potential of joint ventures to create economic growth and sustainable business expansion. Furthermore, partnerships with local companies can help to mitigate econo-political risk, and facilitate buy-in from the national governments that are normally the primary stakeholders in the energy sector ventures (directly or indirectly. The particular case of Eskom Enterprises (Pty Ltd, a wholly owned subsidiary of Eskom, is highlighted.

AFRIKAANSE OPSOMMING: Hierdie artikel ondersoek die begrip gesamentlike onderneming in die internasionale energiesektor en ontwikkel 'n gesamentlike-onderneming-model as 'n sake-ontwikkeling- en takseermodel. Die gesamentlike-onderneming-model bied 'n stelselmatige metode wat op moderne sake-intelligensie staat maak om 'n potensiële sake-onderneming op grond van die tegnologiese en finansiële kernvermoëns daarvan te takseer deur 'n gebalanseerdepuntekaart-tegniek te gebruik. Die model kan deur sake-ontwikkelingsbestuurders gebruik word om die potensiaal van gesamentlike ondernemings in te span om ekonomiese groei en volhoubare sake-uitbreiding daar te stel. Verder kan venootskappe met plaaslike maatskappye help om die ekonomiese risiko te verminder en inkoop te vergemaklik van die nasionale regerings wat gewoonlik die primêre belanghebbendes in die energiesektorondernemings is (hetsy regstreeks of onregstreeks. Die besondere geval van Eskom Enterprises (Edms Bpk, 'n vol filiaal van Eskom

NGNP Data Management and Analysis System Modeling Capabilities

Energy Technology Data Exchange (ETDEWEB)

Cynthia D. Gentillon

2009-09-01

Projects for the very-high-temperature reactor (VHTR) program provide data in support of Nuclear Regulatory Commission licensing of the VHTR. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high temperature and high fluence environments. In addition, thermal-hydraulic experiments are conducted to validate codes used to assess reactor safety. The VHTR Program has established the NGNP Data Management and Analysis System (NDMAS) to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and identifying relationships among the measured quantities that contribute to their understanding.

NGNP Data Management and Analysis System Modeling Capabilities

International Nuclear Information System (INIS)

Gentillon, Cynthia D.

2009-01-01

Projects for the very-high-temperature reactor (VHTR) program provide data in support of Nuclear Regulatory Commission licensing of the VHTR. Fuel and materials to be used in the reactor are tested and characterized to quantify performance in high temperature and high fluence environments. In addition, thermal-hydraulic experiments are conducted to validate codes used to assess reactor safety. The VHTR Program has established the NGNP Data Management and Analysis System (NDMAS) to ensure that VHTR data are (1) qualified for use, (2) stored in a readily accessible electronic form, and (3) analyzed to extract useful results. This document focuses on the third NDMAS objective. It describes capabilities for displaying the data in meaningful ways and identifying relationships among the measured quantities that contribute to their understanding.

Judgmental Forecasting of Operational Capabilities

DEFF Research Database (Denmark)

Hallin, Carina Antonia; Tveterås, Sigbjørn; Andersen, Torben Juul

This paper explores a new judgmental forecasting indicator, the Employee Sensed Operational Capabilities (ESOC). The purpose of the ESOC is to establish a practical prediction tool that can provide early signals about changes in financial performance by gauging frontline employees’ sensing...... of changes in the firm’s operational capabilities. We present the first stage of the development of ESOC by applying a formative measurement approach to test the index in relation to financial performance and against an organizational commitment scale. We use distributed lag models to test whether the ESOC...

RIA testing capability of the transient reactor test facility

International Nuclear Information System (INIS)

Crawford, D.C.; Swanson, R.W.

1999-01-01

The advent of high-burnup fuel implementation in LWRs has generated international interest in high-burnup LWR fuel performance. Recent testing under simulated RIA conditions has demonstrated that certain fuel designs fail at peak fuel enthalpy values that are below existing regulatory criteria. Because many of these tests were performed with non-prototypically aggressive test conditions (i.e., with power pulse widths less than 10 msec FWHM and with non-protoypic coolant configurations), the results (although very informative) do not indisputably identify failure thresholds and fuel behavior. The capability of the TREAT facility to perform simulated RIA tests with prototypic test conditions is currently being evaluated by ANL personnel. TREAT was designed to accommodate test loops and vehicles installed for in-pile transient testing. During 40 years of TREAT operation and fuel testing and evaluation, experimenters have been able to demonstrate and determine the transient behavior of several types of fuel under a variety of test conditions. This experience led to an evolution of test methodology and techniques which can be employed to assess RIA behavior of LWR fuel. A pressurized water loop that will accommodate RIA testing of LWR and CANDU-type fuel has completed conceptual design. Preliminary calculations of transient characteristics and energy deposition into test rods during hypothetical TREAT RIA tests indicate that with the installation of a pressurized water loop, the facility is quite capable of performing prototypic RIA testing. Typical test scenarios indicate that a simulated RIA with a 72 msec FWHM pulse width and energy deposition of 1200 kJ/kg (290 cal/gm) is possible. Further control system enhancements would expand the capability to pulse widths as narrow as 40 msec. (author)

Atmospheric Release Advisory Capability (ARAC)

International Nuclear Information System (INIS)

Dickerson, M.H.

1975-01-01

The chief purpose of ARAC data acquisition program is to provide site officials, who are responsible for ensuring maximum health protection for the endangered site personnel and public, with estimates of the effects of atmospheric releases of hazardous material as rapidly and accurately as possible. ARAC is in the initial stages of being implemented and is therefore susceptible to changes before it reaches its final form. However the concept of ARAC is fully developed and was successfully demonstrated during a feasibility study conducted in June 1974, as a joint effort between the Savannah River Laboratory (SRL) and Lawrence Livermore Laboratory (LLL). Additional tests between SRL and LLL are scheduled for December 1975. While the immediate goal is the application of ARAC to assist a limited number of ERDA sites, the system is designed with sufficient flexibility to permit expanding the service to a large number of sites. Success in ARAC application should provide nuclear facilities with a means to handle better the urgent questions concerning the potential accidental hazards from atmospheric releases in addition to providing the sites with a capability to assess the effort of their normal operations

Fracture Capabilities in Grizzly with the extended Finite Element Method (X-FEM)

Energy Technology Data Exchange (ETDEWEB)

Dolbow, John [Idaho National Lab. (INL), Idaho Falls, ID (United States); Zhang, Ziyu [Idaho National Lab. (INL), Idaho Falls, ID (United States); Spencer, Benjamin [Idaho National Lab. (INL), Idaho Falls, ID (United States); Jiang, Wen [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2015-09-01

Efforts are underway to develop fracture mechanics capabilities in the Grizzly code to enable it to be used to perform deterministic fracture assessments of degraded reactor pressure vessels (RPVs). A capability was previously developed to calculate three-dimensional interaction- integrals to extract mixed-mode stress-intensity factors. This capability requires the use of a finite element mesh that conforms to the crack geometry. The eXtended Finite Element Method (X-FEM) provides a means to represent a crack geometry without explicitly fitting the finite element mesh to it. This is effected by enhancing the element kinematics to represent jump discontinuities at arbitrary locations inside of the element, as well as the incorporation of asymptotic near-tip fields to better capture crack singularities. In this work, use of only the discontinuous enrichment functions was examined to see how accurate stress intensity factors could still be calculated. This report documents the following work to enhance Grizzly’s engineering fracture capabilities by introducing arbitrary jump discontinuities for prescribed crack geometries; X-FEM Mesh Cutting in 3D: to enhance the kinematics of elements that are intersected by arbitrary crack geometries, a mesh cutting algorithm was implemented in Grizzly. The algorithm introduces new virtual nodes and creates partial elements, and then creates a new mesh connectivity; Interaction Integral Modifications: the existing code for evaluating the interaction integral in Grizzly was based on the assumption of a mesh that was fitted to the crack geometry. Modifications were made to allow for the possibility of a crack front that passes arbitrarily through the mesh; and Benchmarking for 3D Fracture: the new capabilities were benchmarked against mixed-mode three-dimensional fracture problems with known analytical solutions.

A guideline for interpersonal capabilities enhancement to support sustainable facility management practice

Science.gov (United States)

Sarpin, Norliana; Kasim, Narimah; Zainal, Rozlin; Noh, Hamidun Mohd

2018-04-01

Facility management is the key phase in the development cycle of an assets and spans over a considerable length of time. Therefore, facility managers are in a commanding position to maximise the potential of sustainability through the development phases from construction, operation, maintenance and upgrade leading to decommission and deconstruction. Sustainability endeavours in facility management practices will contribute to reducing energy consumption, waste and running costs. Furthermore, it can also help in improving organisational productivity, financial return and community standing of the organisation. Facility manager should be empowered with the necessary knowledge and capabilities at the forefront facing sustainability challenge. However, literature studies show a gap between the level of awareness, specific knowledge and the necessary skills required to pursue sustainability in the facility management professional. People capability is considered as the key enabler in managing the sustainability agenda as well as being central to the improvement of competency and innovation in an organisation. This paper aims to develop a guidelines for interpersonal capabilities to support sustainability in facility management practice. Starting with a total of 7 critical interpersonal capabilities factors identified from previous questionnaire survey, the authors conducted an interview with 3 experts in facility management to assess the perceived importance of these factors. The findings reveal a set of guidelines for the enhancement of interpersonal capabilities among facility managers by providing what can be done to acquire these factors and how it can support the application of sustainability in their practice. The findings of this paper are expected to form the basis of a mechanism framework developed to equip facility managers with the right knowledge, to continue education and training and to develop new mind-sets to enhance the implementation of sustainability

[Run the risk: social disadvantage or capability?

Science.gov (United States)

Muñoz-Duque, Luz Adriana

2018-05-10

This article discusses the notions of risk and risk acceptability from a social justice perspective, especially in light of the capability approach proposed by Amartya Sen. The article argues that risk can be the expression of restrictions on subjects' capabilities, deriving from social disadvantages that can be taken for granted in their daily realities. On the other hand, risk can be viewed as an expression of capability in cases where subjects have accepted or admitted the risk through the exercise of freedom, as long as the subjects that relate to the risk do so in keeping with their idea of a good life, the building of which implies the full development of capability for agency. The article concludes with some thoughts on the issues of risk and risk acceptability in the sphere of public health.

Aging and DNA repair capability. [Review

Energy Technology Data Exchange (ETDEWEB)

Tice, R R

1977-01-01

A review of the literature on DNA repair processes in relation to aging is presented under the following headings: DNA repair processes; age-related occurrence of unrepaired DNA lesions; DNA repair capability as a function of age; tissue-specific DNA repair capability; acceleration of the aging process by exposure to DNA damaging agents; human genetic syndromes; and longevity and DNA repair processes. (HLW)

Domestic uranium mining and milling industry. 1984 viability assessment

International Nuclear Information System (INIS)

1985-01-01

This report presents the second annual assessment of the domestic uranium mining and milling industry's resource capability, supply response capability, financial capability, and import commitment dependency. The data and analysis in support of this assessment and the report itself have been developed pursuant to requirements set forth in Section 23(b) of Public Law 97-415, the Nuclear Regulatory Commission (NRC) Authorization Act, which was enacted on January 4, 1983. The report provides information on recent uranium supply, demand, and marketing conditions and projections of the domestic uranium industry's ability to continue to supply the needs of the domestic nuclear power industry through the year 2000. Industry capability is assessed under a variety of assumed conditions with respect to hypothetical disruptions of uranium imports

Assessment of the prediction capability of the TRANSURANUS fuel performance code on the basis of power ramp tested LWR fuel rods

International Nuclear Information System (INIS)

Pastore, G.; Botazzoli, P.; Di Marcello, V.; Luzzi, L.

2009-01-01

The present work is aimed at assessing the prediction capability of the TRANSURANUS code for the performance analysis of LWR fuel rods under power ramp conditions. The analysis refers to all the power ramp tested fuel rods belonging to the Studsvik PWR Super-Ramp and BWR Inter-Ramp Irradiation Projects, and is focused on some integral quantities (i.e., burn-up, fission gas release, cladding creep-down and failure due to pellet cladding interaction) through a systematic comparison between the code predictions and the experimental data. To this end, a suitable setup of the code is established on the basis of previous works. Besides, with reference to literature indications, a sensitivity study is carried out, which considers the 'ITU model' for fission gas burst release and modifications in the treatment of the fuel solid swelling and the cladding stress corrosion cracking. The performed analyses allow to individuate some issues, which could be useful for the future development of the code. Keywords: Light Water Reactors, Fuel Rod Performance, Power Ramps, Fission Gas Burst Release, Fuel Swelling, Pellet Cladding Interaction, Stress Corrosion Cracking

Beyond competencies: using a capability framework in developing practice standards for advanced practice nursing.

Science.gov (United States)

O'Connell, Jane; Gardner, Glenn; Coyer, Fiona

2014-12-01

This paper presents a discussion on the application of a capability framework for advanced practice nursing standards/competencies. There is acceptance that competencies are useful and necessary for definition and education of practice-based professions. Competencies have been described as appropriate for practice in stable environments with familiar problems. Increasingly competencies are being designed for use in the health sector for advanced practice such as the nurse practitioner role. Nurse practitioners work in environments and roles that are dynamic and unpredictable necessitating attributes and skills to practice at advanced and extended levels in both familiar and unfamiliar clinical situations. Capability has been described as the combination of skills, knowledge, values and self-esteem which enables individuals to manage change, be flexible and move beyond competency. A discussion paper exploring 'capability' as a framework for advanced nursing practice standards. Data were sourced from electronic databases as described in the background section. As advanced practice nursing becomes more established and formalized, novel ways of teaching and assessing the practice of experienced clinicians beyond competency are imperative for the changing context of health services. Leading researchers into capability in health care state that traditional education and training in health disciplines concentrates mainly on developing competence. To ensure that healthcare delivery keeps pace with increasing demand and a continuously changing context there is a need to embrace capability as a framework for advanced practice and education. © 2014 John Wiley & Sons Ltd.

The Endogenous Origins of Experience, Routines and Organizational Capabilities

DEFF Research Database (Denmark)

Foss, Nicolai Juul; Felin, Teppo

2011-01-01

In this paper we discuss the origins and emergence of organizational routines and capabilities. We first argue that there are theoretical and endogeneity-related concerns associated with the key antecedents and mechanisms specified by the extant routines and capabilities literature. Specifically,...... or rationalist, choice-based approach can provide a more fruitful (though preliminary) foundation for understanding organizational behavior and capabilities.......In this paper we discuss the origins and emergence of organizational routines and capabilities. We first argue that there are theoretical and endogeneity-related concerns associated with the key antecedents and mechanisms specified by the extant routines and capabilities literature. Specifically......, we explicate the behaviorist and empiricist foundations of the organizational routines and capabilities literature and the extant emphasis placed on experience, repetition, and observation as the key antecedents and mechanisms of routines and capabilities. Based on this discussion we highlight...

A capability study of micro moulding for nano fluidic system manufacture

DEFF Research Database (Denmark)

Calaon, Matteo; Hansen, Hans Nørgaard; Tosello, Guido

2013-01-01

With the present paper the authors analysed process capability of ultra-precision moulding used for producing nano crosses with the same critical channels dimensions of a nano fluidic system for optical mapping of genomic length DNA. The process variation focused on product tolerances is quantified...... through AFM measurements. Uncertainty assessment of measurements on polymer objects is described and quality control results of sub-micro injection moulded crosses are shown in respect of the tolerance range specified by the end user as limit value for functional design....

Developing a Dual-Level Capabilities Approach: Using Constructivist Grounded Theory and Feminist Ethnography to Enhance the Capabilities Approaches

Science.gov (United States)

Hall, Kia M. Q.

2014-01-01

In this study, a dual-level capabilities approach to development is introduced. This approach intends to improve upon individual-focused capabilities approaches developed by Amartya Sen and Martha Nussbaum. Based upon seven months of ethnographic research in the Afro-descendant, autochthonous Garifuna community of Honduras, constructivist grounded…

The Interface of IT Capabilities and Disruptive Innovations

DEFF Research Database (Denmark)

Baiyere, Abayomi

2017-01-01

The occurrence of disruptive innovations tends to challenge the fabric, structure and capability that define firms facing their threat. Prior research indicates that the capacity of a firm to restructure and reconfigure its resources to face/leverage such turbulent situations is dependent on how...... well it can orchestrate its capabilities. Although IT capability has been identified as one of the essential capability of today’s organisations, managers as well as researchers are yet to uncover the dynamics through which an organisation’s IT capability can be leveraged in disruptive innovation...... situations. This paper contributes to our understanding in this direction by conceptually exploring the different roles of an organisation's IT capabilitiy in disruptive innovation scenarios. The paper provides a synthesis of the current state of knowledge about both concepts and extends this to highlight...

Business and IT Capabilities for Cloud Platform Success

DEFF Research Database (Denmark)

Hahn, Christopher; Huntgeburth, Jan; Winkler, Till J.

2016-01-01

The growing proliferation of cloud platform ecosystems demands a deeper understanding of the capabilities that help existing and emerging platform providers to be successful by creating and appropriating value. This multiple case study of four cloud platform providers (three large, one SME......) instantiates Rai and Tang’s (2014) framework of dyadic IT and network IT capabilities for a cloud platform context and extends it by exploring previously undertheorized cloud platform business capabilities. We further build on this extended framework by employing a configurational perspective to elucidate...... the complementary role of the three proposed business capabilities (incentives and rules, ecosystem marketing and sales, partner development and support) for relevant value creation and appropriation mechanisms. In addition to providing a capability framework catered to the cloud platform context, our findings...

Physical and cognitive capability in mid-adulthood as determinants of retirement and extended working life in a British cohort study

OpenAIRE

Stafford, M.; Cooper, R.; Cadar, D.; Carr, E.; Murray, E.; Richards, M.; Stansfeld, S.; Zaninotto, P.; Head, J.; Kuh, D.

2017-01-01

Objective Policy in many industrialized countries increasingly emphasizes extended working life. We examined associations between physical and cognitive capability in mid-adulthood and work in late adulthood. Methods Using self-reported physical limitations and performance-based physical and cognitive capability at age 53, assessed by trained nurses from the Medical Research Council (MRC) National Survey of Health and Development, we examined prospective associations with extended working (ca...

Physical and cognitive capability in mid-adulthood as determinants of retirement and extended working life in a British cohort study

OpenAIRE

Stafford, M.; Cooper, R.; Cadar, D.; Carr, E.; Murray, E.; Richards, M.; Stansfeld, S.; Zaninotto, P.; Head, J.; Kuh, D.

2017-01-01

OBJECTIVE: Policy in many industrialized countries increasingly emphasizes extended working life. We examined associations between physical and cognitive capability in mid-adulthood and work in late adulthood. METHODS: Using self-reported physical limitations and performance-based physical and cognitive capability at age 53, assessed by trained nurses from the Medical Research Council (MRC) National Survey of Health and Development, we examined prospective associations with extended working (...

Advanced simulation capability for environmental management - current status and future applications

Energy Technology Data Exchange (ETDEWEB)

Freshley, Mark; Scheibe, Timothy [Pacific Northwest National Laboratory, Richland, Washington (United States); Robinson, Bruce; Moulton, J. David; Dixon, Paul [Los Alamos National Laboratory, Los Alamos, New Mexico (United States); Marble, Justin; Gerdes, Kurt [U.S. Department of Energy, Office of Environmental Management, Washington DC (United States); Stockton, Tom [Neptune and Company, Inc, Los Alamos, New Mexico (United States); Seitz, Roger [Savannah River National Laboratory, Aiken, South Carolina (United States); Black, Paul [Neptune and Company, Inc, Lakewood, Colorado (United States)

2013-07-01

The U.S. Department of Energy (US DOE) Office of Environmental Management (EM), Office of Soil and Groundwater (EM-12), is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach that is currently aimed at understanding and predicting contaminant fate and transport in natural and engineered systems. ASCEM is a modular and open source high-performance computing tool. It will be used to facilitate integrated approaches to modeling and site characterization, and provide robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of capabilities, with current emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Tool-sets and High-Performance Computing (HPC) multi-process simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The integration of the Platform and HPC capabilities were tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities in 2012. The current maturity of the ASCEM computational and analysis capabilities has afforded the opportunity for collaborative efforts to develop decision analysis tools to support and optimize radioactive waste disposal. Recent advances in computerized decision analysis frameworks provide the perfect opportunity to bring this capability into ASCEM. This will allow radioactive waste

Pilot project - demonstration of capabilities and benefits of bridge load rating through physical testing : tech transfer summary.

Science.gov (United States)

2013-08-01

This project demonstrated the capabilities for load testing bridges in Iowa, developed and presented a webinar to local and state engineers, and produced a spreadsheet and benefit evaluation matrix that others can use to preliminarily assess where br...

Liberalism, Humanism, and Feminism in Nussbaum's Capabilities ...

African Journals Online (AJOL)

A purely theoretical analysis of Martha Nussbaum's basis of the capabilities ... Since even a capabilities approach rooted in feminist justice is itself radical and must ... rhetoric of sex and social justice that has already been embraced by current

Conceptual Model of IT Infrastructure Capability and Its Empirical Justification

Institute of Scientific and Technical Information of China (English)

QI Xianfeng; LAN Boxiong; GUO Zhenwei

2008-01-01

Increasing importance has been attached to the value of information technology (IT) infrastructure in today's organizations. The development of efficacious IT infrastructure capability enhances business performance and brings sustainable competitive advantage. This study analyzed the IT infrastructure capability in a holistic way and then presented a concept model of IT capability. IT infrastructure capability was categorized into sharing capability, service capability, and flexibility. This study then empirically tested the model using a set of survey data collected from 145 firms. Three factors emerge from the factor analysis as IT flexibility, IT service capability, and IT sharing capability, which agree with those in the conceptual model built in this study.

Recent Investments by NASA's National Force Measurement Technology Capability

Science.gov (United States)

Commo, Sean A.; Ponder, Jonathan D.

2016-01-01

The National Force Measurement Technology Capability (NFMTC) is a nationwide partnership established in 2008 and sponsored by NASA's Aeronautics Evaluation and Test Capabilities (AETC) project to maintain and further develop force measurement capabilities. The NFMTC focuses on force measurement in wind tunnels and provides operational support in addition to conducting balance research. Based on force measurement capability challenges, strategic investments into research tasks are designed to meet the experimental requirements of current and future aerospace research programs and projects. This paper highlights recent and force measurement investments into several areas including recapitalizing the strain-gage balance inventory, developing balance best practices, improving calibration and facility capabilities, and researching potential technologies to advance balance capabilities.

ANTECEDENTS OF CUSTOMER RELATIONSHIP MANAGEMENT CAPABILITIES

Directory of Open Access Journals (Sweden)

Tuleu Daniela

2015-07-01

Full Text Available Customer relationship management, as a process to manage customer relationship initiation, maintenance and termination to maximize the value of the relationship portfolio, is an evolving process. In recent years, the development of interactive technologies (social media have revolutionized the interaction between firms and their customers and between customers. The impact of technology on CRM is improving ways of collecting and processing customer information and transforming communication with customers. In the context of the development of social networks, the introduction of social media applications in customer relationship management activities bring important changes in this area. Thus, managers need to pay attention to the interaction management as an important process of CRM and enhance the customer relationship management capabilities. The study propose a conceptual research model of several antecedents of customer relationship managements capabilities and provide the linkage between this antecedents and CRM capabilities. First, following review of existing research literature related to customer relationship management, there are some conceptual clarification on customer relationship management. Second, are presented the working concepts: the adoption of interactive technologies, customer concept, customer empowerment, customer relationship orientation and customer-centric management system. Then, it is proposed the conceptual model and finally are presented conclusions, managerial implications, limitations and research directions. From a theoretical perspective, this paper highlights the importance of marketing actions at the individual customer level and reveal the impact of adoption by companies of interactive technologies so that organizations have the opportunity to engage in conversations with customers and respond in real time the requirements that they launched the online environment. Nowadays, customers feel empowered and play

Assessment of capability for modeling the core degradation in 2D geometry with ASTEC V2 integral code for VVER type of reactor

International Nuclear Information System (INIS)

Dimov, D.

2011-01-01

The ASTEC code is progressively becoming the reference European severe accident integral code through in particular the intensification of research activities carried out since 2004. The purpose of this analysis is to assess ASTEC code modelling of main phenomena arising during hypothetical severe accidents and particularly in-vessel degradation in 2D geometry. The investigation covers both early and late phase of degradation of reactor core as well as determination of corium which will enter the reactor cavity. The initial event is station back-out. In order to receive severe accident condition, failure of all active component of emergency core cooling system is apply. The analysis is focus on ICARE module of ASTEC code and particularly on so call MAGMA model. The aim of study is to determine the capability of the integral code to simulate core degradation and to determine the corium composition entering the reactor cavity. (author)

Nanofabrication principles, capabilities and limits

CERN Document Server

Cui, Zheng

2017-01-01

This second edition of Nanofabrication is one of the most comprehensive introductions on nanofabrication technologies and processes. A practical guide and reference, this book introduces readers to all of the developed technologies that are capable of making structures below 100nm. The principle of each technology is introduced and illustrated with minimum mathematics involved. Also analyzed are the capabilities of each technology in making sub-100nm structures, and the limits of preventing a technology from going further down the dimensional scale. This book provides readers with a toolkit that will help with any of their nanofabrication challenges.

Drift reversal capability in helical systems

International Nuclear Information System (INIS)

Yokoyama, M.; Itoh, K.; Okamura, S.

2002-10-01

The maximum-J (J is the second adiabatic invariant) capability, i.e., the drift reversal capability, is examined in quasi-axisymmetric (QAS) stellarators and quasi-poloidally symmetric (QPS) stellarators as a possible mechanism for turbulent transport suppression. Due to the existence of non-axisymmetry of the magnetic field strength in QAS configurations, a local maximum of J is created to cause the drift reversal. The increase of magnetic shear in finite beta equilibria also has favorable effect in realizing the drift reversal. The radial variation of the uniform magnetic field component plays a crucial role for the drift reversal in a QPS configuration. Thus, the drift reversal capability and its external controllability are demonstrated for QAS and QPS stellarators, by which the impact of magnetic configuration on turbulent transport can be studied in experiments. (author)

Drift reversal capability in helical systems

International Nuclear Information System (INIS)

Yokoyama, M.; Itoh, K.; Okamura, S.; Matsuoka, K.; Nakajima, N.; Itoh, S.-I.; Neilson, G.H.; Zarnstorff, M.C.; Rewoldt, G.

2003-01-01

The maximum-J (J is the second adiabatic invariant) capability, i.e., the drift reversal capability, is examined in quasi-axisymmetric (QAS) stellarators and quasi-poloidally symmetric (QPS) stellarators as a possible mechanism for turbulent transport suppression. Due to the existence of non-axisymmetry of the magnetic field strength in QAS configurations, a local maximum of J is created to cause the drift reversal. The increase of magnetic shear in finite beta equilibria also has favorable effect in realizing the drift reversal. The radial variation of the uniform magnetic field component plays a crucial role for the drift reversal in a QPS configuration. Thus, the drift reversal capability and its external controllability are demonstrated for QAS and QPS stellarators, by which the impact of magnetic configuration on turbulent transport can be studied in experiments. (author)

An Interoperability Framework and Capability Profiling for Manufacturing Software

Science.gov (United States)

Matsuda, M.; Arai, E.; Nakano, N.; Wakai, H.; Takeda, H.; Takata, M.; Sasaki, H.

ISO/TC184/SC5/WG4 is working on ISO16100: Manufacturing software capability profiling for interoperability. This paper reports on a manufacturing software interoperability framework and a capability profiling methodology which were proposed and developed through this international standardization activity. Within the context of manufacturing application, a manufacturing software unit is considered to be capable of performing a specific set of function defined by a manufacturing software system architecture. A manufacturing software interoperability framework consists of a set of elements and rules for describing the capability of software units to support the requirements of a manufacturing application. The capability profiling methodology makes use of the domain-specific attributes and methods associated with each specific software unit to describe capability profiles in terms of unit name, manufacturing functions, and other needed class properties. In this methodology, manufacturing software requirements are expressed in terns of software unit capability profiles.

Towards a national cybersecurity capability development model