WorldWideScience

Sample records for assembly line worker

  1. [Occupational stress of assembly line female workers in confectionery work].

    Science.gov (United States)

    Kondo, Y; Sato, Y; Takashima, H; Siki, T; Inui, S; Arachi, H; Yamashita, N; Hosokawa, M

    1985-09-01

    Concomitant with frequent occurrence of disorders of the neck, arm, hand and low back among assembly-line female workers in confectionery work, there is an increased number of patients with occupational cervicobrachial disorders and/or low back pain. In suspicion of the close correlation between the working conditions and development of these local disorders, a field study was undertaken. The following are the results obtained. More than 90% of these assembly-line female workers consisted of inexperienced part-time employees, mostly of middle to old age. They were engaged in decorating conveyor-carried cakes with cream and chocolate. The work necessitated repetitive movements of the upper limbs and concentration of visuosensory and nervous attention in a half-sitting slouching posture. This was considered to exert excess load on the local muscles and nervous and sensory systems. The causes that intensified the local symptoms as pointed out by the workers consisted of (1) repetitive use of the arms and hands, (2) static posture during the work and (3) sustained standing position. Complaints of low back pain were conspicuous from the unsuitable height of a conveyor-belt. Thirty five percent of the female workers needed medical treatment for cervicobrachial and/or low back pain. The forced adaptation to the belt height, sustained unnatural working posture and the imposition of forced movements seemed to be the main factors in the onset of cervicobrachial and/or low back pain in interrelation with working hours. On the basis of these results, the work load on a machine-paced assembly-line was analyzed and the necessity of improvement of working conditions was discussed.

  2. [Occupational stress in assembly line workers in electronics manufacturing service and related influencing factors].

    Science.gov (United States)

    Ji, Y Q; Li, S; Wang, C; Wang, J; Liu, X M

    2016-10-20

    Objective: To investigate occupational stress in assembly line workers in electronics manu-facturing service (EMS) and related influencing factors. Methods: From June to October, 2015, a cross-sectional survey was performed for 5 944 assembly line workers in EMS (observation group) and 6 270 workers from other posts (non-assembly line workers and management personnel; control group) using the self-made questionnaire for basic information, job demand-control (JDC) model questionnaire, and effort-reward imbalance (ERI) model questionnaire to collect respondents' basic information and occupational stress. Results: The observation group had significantly lower work autonomy, social support, and work reward scores than the control group (2.72 ± 0.63/3.64 ± 0.68/4.06 ± 0.80 vs 3.00 ± 0.67/3.83 ± 0.68/4.24 ± 0.75, t =23.53, 15.41, and 12.70, all P occupational stress determined by JDC and ERI models than the control group (64.5%/12.7% vs 52.6%/9.9%, χ 2 =182.26 and 23.41, both P 60 hours/week, and sleeping time occupational stress in JDC model; education background of Bachelor's degree or above, working time >60 hours/week, and sleeping timeoccupational stress in ERI model, while female sex and a high monthly income reduced the risk of occupational stress in ERI model. Conclusion: Assembly line workers in EMS are a relatively vulnerable group and have a high degree of occupational stress. Working time >60 hours/week and sleeping time occupational stress.

  3. Relationship between workload and low back pain in assembly line workers

    Directory of Open Access Journals (Sweden)

    Reza Kalantari

    2016-06-01

    Full Text Available Introduction: Work pressure and excessive workload can jeopardize and impair the people’s health. One of these impairments is musculoskeletal disorders. Among these disorders, low back pain is the most common and most costly problem. The purpose of this study was to investigate the relationship between workload and prevalence of low back pain in assembly line workers of a car manufacturing factory. Methods: This cross-sectional study was conducted on 69 workers working in the assembly line of a factory. Data collection tools included three questionnaires: demographic questionnaire, NASA Task Load Index (NASA-TLX and Cornell Musculoskeletal Discomfort Questionnaire (CMDQ. Data were analyzed by descriptive and inferential (T-test and One-way ANOVA statistics. Results: Of the workers, 72.5% were female. The average total workload was 71.42% and the prevalence of musculoskeletal disorders in low back was 43.37%. The results of the analysis of relationship between workload and the prevalence of low back pain showed a significant relationship between physical/ mental workload and the incidence of low back pain (P<0.05. Conclusion: The more is the workload on the person, the greater is the risk of low back pain. Measures such as increasing the number of workers to distribute the workload, slowing the work pace, having work-rest periods for workers, improving psychological conditions of work, etc. can be useful in this regard.

  4. Field study of age-differentiated strain for assembly line workers in the automotive industry.

    Science.gov (United States)

    Börner, Kerstin; Scherf, Christian; Leitner-Mai, Bianca; Spanner-Ulmer, Birgit

    2012-01-01

    A field study in an automotive supply industry company was conducted to explore age-differentiated strain of assembly line workers. Subjective and objective data from 23 female workers aged between 27 and 57 years were collected at the workplace belt buckle assembly during morning shifts. Subjects with medication or chronic diseases affecting heart rate and breath rate were excluded. For subjective data generation different questionnaires were used. Before the Work Ability Index and the Munich Chronotype Questionnaire were completed by the subjects. Short questionnaires (strain-ratings, NASA-TLX) directly at begin and end of the work were used for obtaining shift-related data. During the whole shift (6 a.m. - 2.45 p.m.) bodily functions were logged with a wireless chest strap. In addition, the motion of the hand-arm-system was recorded for 30 times, 3 minutes each after a fixed time-schedule. First results show that younger subjects need significant less time for assembly (mean = 14.940 s) compared to older subjects (mean = 17.040 s; t(472.026) = -9.278 , p < 0.01).

  5. [An assembly line lighting survey analysis and its optimal illumination range research].

    Science.gov (United States)

    Yang, Xin-ning; Xu, Yan; DU, Wei-wei; Cao, Lei; Wang, Sheng; Dong, Xue-mei; Lu, Hou-han; Chen, Song-gen; Cao, Xiao-ou; Zhang, Long-lian; He, Li-hua

    2011-06-18

    To investigate and analyze present conditions of the assembling line illumination in our country, and to set the recommended values of illuminance standard. Questionnaires and field surveys were used in this investigation. A total of 752 workers from seven factories in textile, shoes and electronics industries were selected for the questionnaire survey and site measurement, and corresponding analyses made with SPSS 13.0 statistic software. Uniformity of illumination, definition in working face, general satisfactory degrees, asthenopia were significantly correlated with each other. Assembly line illuminances for five different visual characteristics were recommended in this paper. The illuminances were 500-1 000-1 500 lx, 300-500-1 000 lx, 200-300-750 lx, 100-300-500 lx, 50-100-200 lx, respectively. Present conditions of the assembling line illumination are less than satisfactory, uniformity of illumination is on the low side, and there is no assembling line illuminance standard for general satisfactory degrees and asthenopia of workers. The related work should be further improved.

  6. Lean manufacturing implementation in reducing waste for electronic assembly line

    Directory of Open Access Journals (Sweden)

    Zakaria Nurul Husna

    2017-01-01

    Full Text Available Lean manufacturing is the most convenient way to eliminate unnecessary waste and can provide what customers demand. This paper presents possibilities and sustainability of application of lean manufacturing method by using a virtual simulation of the workers performance in a line production of small and medium industry. Actual case study and Witness simulation were used in this study to find the waste that exists in the production and identified the performance of workers in the production line. Lean manufacturing concept has identified and rectified problems related to low productivity in the assembly line. The case study is involved a line production for electronic part assembly. The result of this preliminary study should illustrate the relationship of worker’s performance by lean manufacturing method as well as the productivity improvements which help to reduce cost for manufacturer. Lean manufacturing method has been used during the study to reduce the cost when waste is eliminated by reducing the workstation without reducing the performance of the production. The performance of the production is increased when allocating the labor in a needed working area. Lastly, the study also proves that the new layout has improved the process to be used for future production process.

  7. Heuristics comparison for u-shaped assembly line balancing in the apparel factory

    Directory of Open Access Journals (Sweden)

    Nuchsara Kriengkorakot

    2014-06-01

    Full Text Available In recent year, many industries have adopted a Just-in-time (JIT approach to manufacturing. One of the important changes resulting from JIT implementation is the replacement of the traditional straight lines with Ushaped assembly lines. The important characteristic of these new configurations is that multiskilled workers perform various tasks of different stations along the production line. This research is to improve the assembly line balancing in apparel factory in case study of T-shirt style 53287. The efficiency of production line was 55.48%, the factory balanced line with the traditional method in straight line. Then, the u-shaped assembly line balancing problem (UALBP is to be performed instead of straight line. By using the heuristics of Maximum Task Time, Minimum Task Time, Maximum Ranked Positional Weight (RPWmax and Greedy Randomized to determine the optimal solutions related to the number of stations and line efficiency. The results indicate that two heuristics have given the good solution which have produced by the use of Maximum Task Time and Greedy Randomized. The minimum number of stations have reduced from 17 stations to 11 stations in UALB and the line efficiency was increased from 55.48% to 85.75%. The U-line configuration frequently improves the line efficiency and has fewer work stations compared to the traditional lines.

  8. [Relationship between performance rating and risk of low back pain in manufacturing line workers].

    Science.gov (United States)

    Higuchi, Yoshiyuki; Funahashi, Atsushi; Izumi, Hiroyuki; Kumashinro, Masaharu

    2012-03-01

    It is possible that the performance rating of line workers is affected by the risk factors for musculoskeletal disorders that are included in their work more so than by the actual takt time. To investigate whether performance rating relates to the risk factors for musculoskeletal disorders, we analyzed a dataset obtained from a self-administered questionnaire answered by assembly line workers (n=1579). As a result, performance rating had a significant association with unsuitable work environments, poor working postures and handling of heavy loads. The workers who reported the fastest rating had a higher exposure than others to the risk factors for occupational low back pain. The results of our study support the effectiveness of performance rating as an index of work burden.

  9. Assembly line performance and modeling

    Science.gov (United States)

    Rane, Arun B.; Sunnapwar, Vivek K.

    2017-09-01

    Automobile sector forms the backbone of manufacturing sector. Vehicle assembly line is important section in automobile plant where repetitive tasks are performed one after another at different workstations. In this thesis, a methodology is proposed to reduce cycle time and time loss due to important factors like equipment failure, shortage of inventory, absenteeism, set-up, material handling, rejection and fatigue to improve output within given cost constraints. Various relationships between these factors, corresponding cost and output are established by scientific approach. This methodology is validated in three different vehicle assembly plants. Proposed methodology may help practitioners to optimize the assembly line using lean techniques.

  10. Harnessing natural product assembly lines: structure, promiscuity, and engineering.

    Science.gov (United States)

    Ladner, Christopher C; Williams, Gavin J

    2016-03-01

    Many therapeutically relevant natural products are biosynthesized by the action of giant mega-enzyme assembly lines. By leveraging the specificity, promiscuity, and modularity of assembly lines, a variety of strategies has been developed that enables the biosynthesis of modified natural products. This review briefly summarizes recent structural advances related to natural product assembly lines, discusses chemical approaches to probing assembly line structures in the absence of traditional biophysical data, and surveys efforts that harness the inherent or engineered promiscuity of assembly lines for the synthesis of non-natural polyketides and non-ribosomal peptide analogues.

  11. An Optimal Balancing of Multiple Assembly Line For a Batch Production Unit

    Directory of Open Access Journals (Sweden)

    M. Mohan Prasad

    2013-12-01

    Full Text Available Higher Productivity in organizations leads to national prosperity and better standard of living for the whole community. This has motivated several workers on productivity improvement at different levels of XXXX India Pvt Ltd, Chennai. The main objective of this project is to increase the production by changing the layout of the assembly line in making of Transmit Mixer. At present 12 machines are being manufactured in a total of 2 shifts per day. Time study is carried out to identify and avoid the idle time to increase the production rate to 24 machines per day. The organization facing the problems like production time, online inventory, delay and idle time. Here our objective is to reduce the idle time, identifying the cycle time and optimal method of production. The COMSOAL (Computer Method for Sequencing Operations for Assembly Lines and RPW (Ranked Positional Weight algorithms have been used to get the optimal solution. This algorithm provides the better solution, thereby reducing unnecessary movements of the worker within the station. The overall cycle time got reduced when compared with the existing cycle time in order to meet the customer demand. Thus we are proposing this scientific approach to get the optimal solution for increased rate of production of the company without affecting the quality and cost.

  12. ASSEMBLY LINE BALANCING in a CLOTHING COMPANY

    Directory of Open Access Journals (Sweden)

    HASNALCACI Kubra

    2017-05-01

    Full Text Available Assembly lines take the attention of researchers and companies because of its great effect on efficiency. Efficiency in assembly lines has an important role on cost and quality which are the basic fundamentals of competition. Assembly lines contain a number of workstations and tasks (jobs are processed in these stations and are moved from station to station. The tasks are assigned to each station regarding a cycle time. The cycle time is the maximum available time for the production of a job at any workstation. The assingning of jobs to workstations is based on the objective of minimizing the workflow among the workstations, reducing the throughput time as well as the work in progress and thus increasing productivity. If the jobs are not allocated in balance, this will cause idle workstations and waste of workforce besides the loss of overall efficiency. In this study, an assebly line balancing problem was examined for a five pocket denim trousers in a clothing company. Firstly, priority associations and standard durations of operations of denim trousers were determined. Then, assembly line balancing study was carried out by using ranked positional weights assembly line balancing method developed by Helgeson and Birnie to increase the production in a clothing company manufacturing five pocket denim trousers.

  13. A Novel Assembly Line Balancing Method Based on PSO Algorithm

    Directory of Open Access Journals (Sweden)

    Xiaomei Hu

    2014-01-01

    Full Text Available Assembly line is widely used in manufacturing system. Assembly line balancing problem is a crucial question during design and management of assembly lines since it directly affects the productivity of the whole manufacturing system. The model of assembly line balancing problem is put forward and a general optimization method is proposed. The key data on assembly line balancing problem is confirmed, and the precedence relations diagram is described. A double objective optimization model based on takt time and smoothness index is built, and balance optimization scheme based on PSO algorithm is proposed. Through the simulation experiments of examples, the feasibility and validity of the assembly line balancing method based on PSO algorithm is proved.

  14. A Novel Assembly Line Scheduling Algorithm Based on CE-PSO

    Directory of Open Access Journals (Sweden)

    Xiaomei Hu

    2015-01-01

    Full Text Available With the widespread application of assembly line in enterprises, assembly line scheduling is an important problem in the production since it directly affects the productivity of the whole manufacturing system. The mathematical model of assembly line scheduling problem is put forward and key data are confirmed. A double objective optimization model based on equipment utilization and delivery time loss is built, and optimization solution strategy is described. Based on the idea of solution strategy, assembly line scheduling algorithm based on CE-PSO is proposed to overcome the shortcomings of the standard PSO. Through the simulation experiments of two examples, the validity of the assembly line scheduling algorithm based on CE-PSO is proved.

  15. Biosynthesis: Reprogramming assembly lines

    Science.gov (United States)

    Menon, Binuraj R. K.; Jenner, Matthew

    2018-03-01

    Rational engineering of biosynthetic assembly lines for production of new compounds is an attractive prospect, yet it presents many challenges. Learning from biology, some of the rules for expanding the chemical diversity of non-ribosomal peptides have been uncovered in two recent studies.

  16. [The epidemiological study of work-related musculoskeletal disorders and related factors among automobile assembly workers].

    Science.gov (United States)

    Wang, Zhong-Xu; Qin, Ru-Li; Li, Yu-Zhen; Zhang, Xue-Yan; Jia, Ning; Zhang, Qiu-Ling; Li, Gang; Zhao, Jie; Li, Huan-Huan; Jiang, Hai-Qiang

    2011-08-01

    To investigate the work-related musculoskeletal disorders among automobile assembly workers, to discusses the related risk factors and their relationship. The selected 1508 automobile assembly workers from a north car manufacturing company were regarded as the study object. The hazard zone jobs checklist, Nordic musculoskeletal symptom questionnaire (NMQ) and pain questionnaire were used to perform the epidemiological cross-sectional and retrospective survey and study for the General status, awkward ergonomics factors and related influencing factors, and musculoskeletal disorders of workers. The predominant body sites of occurring WMSDs among automobile assembly workers were mainly low back, wrist, neck and shoulders, the predominant workshop section of occurring WMSDs were mostly concentrated in engine compartment, interior ornament, door cover, chassis and debugging section. The predominant body site of WMSDs among engine compartment and chassis section workers was low back, interior ornament workers were low back and wrist, door cover workers was wrist, chassis workers was low back, debugging workers were neck and low back. Neck musculoskeletal disorders had the trend with the increase of a body height; Smoking may increase the occurrence of musculoskeletal disorders. The WMSDs appears to be a serious ergonomic proble assem among automobile assembly workers, predominant occurring site of WMSDs is with different workshop section, its characteristics is quite obvious, probably related to its existing awkward work position or activities. The worker height and smoking habits may be important factors which affect musculoskeletal disorders happen.

  17. Assembly delay line pulse generators

    CERN Multimedia

    CERN PhotoLab

    1971-01-01

    Assembly of six of the ten delay line pulse generators that will power the ten kicker magnet modules. One modulator part contains two pulse generators. Capacitors, inductances, and voltage dividers are in the oil tank on the left. Triggered high-pressure spark gap switches are on the platforms on the right. High voltage pulse cables to the kicker magnet emerge under the spark gaps. In the centre background are the assembled master gaps.

  18. Postural loading assessment in assembly workers of an Iranian telecommunication manufacturing company.

    Science.gov (United States)

    Kamalinia, Mojtaba; Nasl Saraji, Gebreal; Kee, Dohyung; Hosseini, Mostafa; Choobineh, Alireza

    2013-01-01

    Changes in industries and work practices have coincided with work-related musculoskeletal disorders (MSDs). This study was conducted to determine the prevalence of MSDs and to assess postural loading in assembly workers of an Iranian telecommunication manufacturing company. Data were collected from 193 randomly selected workers in 4 units of the company. The Nordic musculoskeletal disorders questionnaire and the UBC ergonomic checklist were used as data collection tools. Loading on the upper body assessment (LUBA) was used to assess postural loading. Lower back symptoms were the most prevalent problems among the workers (67.9%). LUBA showed that most assembly workers (94.3%) had experienced considerable and high postural loading (postural load index, PLI > 5). Regression analyses revealed that lighting, rotation, contact stress, repetition, gender and age were factors associated with symptoms. Work-related MSDs occurred at a high rate among workers. Postural loading requires consideration. Any ergonomic intervention should focus on eliminating ergonomic factors associated with symptoms.

  19. A simulation-based approach for solving assembly line balancing problem

    Science.gov (United States)

    Wu, Xiaoyu

    2017-09-01

    Assembly line balancing problem is directly related to the production efficiency, since the last century, the problem of assembly line balancing was discussed and still a lot of people are studying on this topic. In this paper, the problem of assembly line is studied by establishing the mathematical model and simulation. Firstly, the model of determing the smallest production beat under certain work station number is anysized. Based on this model, the exponential smoothing approach is applied to improve the the algorithm efficiency. After the above basic work, the gas stirling engine assembly line balancing problem is discussed as a case study. Both two algorithms are implemented using the Lingo programming environment and the simulation results demonstrate the validity of the new methods.

  20. Respiratory impairment due to asbestos exposure in brake-lining workers

    International Nuclear Information System (INIS)

    Erdinc, M.; Erdinc, E.; Cok, G.; Polatli, M.

    2003-01-01

    There is extensive evidence that exposure to asbestos causes pulmonary parenchyma fibrosis, pleural disease, and malignant neoplasm in asbestos-exposed workers. However, few data concerning brake-lining workers are available in the literature. In this study, we aimed to assess the long-term effects of chrysotile asbestos exposure on lung function and the risk of asbestos-related diseases in brake-lining workers. Seventy-four asbestos-exposed workers who processed brake-lining products and 12 unexposed office workers were offered pulmonary function tests (spirometry and transfer actor) in 1992 and 1999. In 1999, the mean duration of asbestos exposure was 0.00±4.07 and 11.02±4.81 years (7-31 years) in non smoking and smoking asbestos workers, respectively. Transfer factor (T L , CO) and transfer coefficient (K CO ) decline were significant in the 7-year follow-up in both smoking and non smoking asbestos workers. However, lung function indices of he control group, whom were all current smokers; were also found to be decreased, including FEF 75 , T L , CO and K CO . We found minimal reticular changes in 10 asbestos workers who were all current smokers, they underwent high-resolution computed tomography scans of the chest and we found that they ad peri bronchial thickening resulting from smoking. As a conclusion, even in the absence of radiographic asbestosis, T L , CO and K CO may decrease after mean 10-year duration of exposure to asbestos in brake-lining workers and this is more noticeable with cigarette burden

  1. Harnessing Thin-Film Continuous-Flow Assembly Lines.

    Science.gov (United States)

    Britton, Joshua; Castle, Jared W; Weiss, Gregory A; Raston, Colin L

    2016-07-25

    Inspired by nature's ability to construct complex molecules through sequential synthetic transformations, an assembly line synthesis of α-aminophosphonates has been developed. In this approach, simple starting materials are continuously fed through a thin-film reactor where the intermediates accrue molecular complexity as they progress through the flow system. Flow chemistry allows rapid multistep transformations to occur via reaction compartmentalization, an approach not amenable to using conventional flasks. Thin film processing can also access facile in situ solvent exchange to drive reaction efficiency, and through this method, α-aminophosphonate synthesis requires only 443 s residence time to produce 3.22 g h(-1) . Assembly-line synthesis allows unprecedented reaction flexibility and processing efficiency. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Harmony Search for Balancing Two-sided Assembly Lines

    Directory of Open Access Journals (Sweden)

    Hindriyanto Dwi Purnomo

    2012-01-01

    Full Text Available Two-sided assembly lines balancing problems are important problem for large-sized products such as cars and buses, in which, tasks operations can be performed in the two sides of the line. In this paper, Harmony Search algorithm is proposed to solve two-sided assembly lines balancing problems type-I (TALBP-I. The proposed method adopts the COMSOAL heuristic and specific features of TALBP in the Harmony operators – the harmony memory consideration, random selection and pitch adjustment – in order to maintain the local and global search. The proposed method is evaluated based on 6 benchmark problems that are commonly used in TALBP. The experiment results show that the proposed method work well and produces better solution than the heuristic method and genetic algorithm.

  3. optimal assembly line balancing using simulation techniques

    African Journals Online (AJOL)

    user

    Department of Mechanical Engineering ... perspective on how the business operates, and ... Process simulation allows management ... improvement and change since it would be a costly ... The work content performed on an assembly line.

  4. Restless Legs Syndrome in shift workers: A cross sectional study on male assembly workers

    Directory of Open Access Journals (Sweden)

    Rahimi Mohsen

    2009-09-01

    Full Text Available Abstract Background Restless Legs Syndrome (RLS is a common neurological movement disorder characterized by symptoms that follow a circadian pattern. Night and rotating shift work schedules exert adverse effects on functions of the human body by disturbing circadian rhythms, and they are known to cause sleep disturbances and insomnia. In this paper, we investigate the possible association between shift work and RLS. Methods This cross sectional study was conducted in an automobile manufacturing factory in Tehran, Iran. A total of 780 male assembly workers were recruited in three groups, each with 260 workers: workers on a permanent morning shift (A and two different rotating shift schedules (B and C with morning, afternoon and night shifts. We used the international RLS study group criteria for diagnosis of RLS, and the severity scale for severity assessment in subjects with RLS. Self administered questionnaires were used to gather information on age, smoking, work history, medical condition, and existence and severity of RLS symptoms. Results The prevalence of RLS was significantly higher in rotational shift workers (15% than workers with permanent morning work schedule (8.5%. In workers suffering from RLS, we found greater mean values of age and work experience, higher percentages of drug consumption, smoking, and co-morbid illnesses compared with subjects who did not have RLS, although these differences were statistically significant only for age, work experience and drug consumption. Conclusion Rotational shift work acts as a risk or exacerbating factor for Restless Legs Syndrome.

  5. Restless Legs Syndrome in shift workers: A cross sectional study on male assembly workers.

    Science.gov (United States)

    Sharifian, Akbar; Firoozeh, Marjan; Pouryaghoub, Gholamreza; Shahryari, Mehran; Rahimi, Mohsen; Hesamian, Mohammad; Fardi, Ali

    2009-09-14

    Restless Legs Syndrome (RLS) is a common neurological movement disorder characterized by symptoms that follow a circadian pattern. Night and rotating shift work schedules exert adverse effects on functions of the human body by disturbing circadian rhythms, and they are known to cause sleep disturbances and insomnia. In this paper, we investigate the possible association between shift work and RLS. This cross sectional study was conducted in an automobile manufacturing factory in Tehran, Iran. A total of 780 male assembly workers were recruited in three groups, each with 260 workers: workers on a permanent morning shift (A) and two different rotating shift schedules (B and C) with morning, afternoon and night shifts. We used the international RLS study group criteria for diagnosis of RLS, and the severity scale for severity assessment in subjects with RLS. Self administered questionnaires were used to gather information on age, smoking, work history, medical condition, and existence and severity of RLS symptoms. The prevalence of RLS was significantly higher in rotational shift workers (15%) than workers with permanent morning work schedule (8.5%). In workers suffering from RLS, we found greater mean values of age and work experience, higher percentages of drug consumption, smoking, and co-morbid illnesses compared with subjects who did not have RLS, although these differences were statistically significant only for age, work experience and drug consumption. Rotational shift work acts as a risk or exacerbating factor for Restless Legs Syndrome.

  6. Analysis of the type II robotic mixed-model assembly line balancing problem

    Science.gov (United States)

    Çil, Zeynel Abidin; Mete, Süleyman; Ağpak, Kürşad

    2017-06-01

    In recent years, there has been an increasing trend towards using robots in production systems. Robots are used in different areas such as packaging, transportation, loading/unloading and especially assembly lines. One important step in taking advantage of robots on the assembly line is considering them while balancing the line. On the other hand, market conditions have increased the importance of mixed-model assembly lines. Therefore, in this article, the robotic mixed-model assembly line balancing problem is studied. The aim of this study is to develop a new efficient heuristic algorithm based on beam search in order to minimize the sum of cycle times over all models. In addition, mathematical models of the problem are presented for comparison. The proposed heuristic is tested on benchmark problems and compared with the optimal solutions. The results show that the algorithm is very competitive and is a promising tool for further research.

  7. Security warning method and system for worker safety during live-line working

    Science.gov (United States)

    Jiang, Chilong; Zou, Dehua; Long, Chenhai; Yang, Miao; Zhang, Zhanlong; Mei, Daojun

    2017-09-01

    Live-line working is an essential part in the operations in an electric power system. Live-line workers are required to wear shielding clothing. Shielding clothing, however, acts as a closed environment for the human body. Working in a closed environment for a long time can change the physiological responses of the body and even endanger personal safety. According to the typical conditions of live-line working, this study synthesizes environmental factors related to shielding clothing and the physiological factors of the body to establish the heart rate variability index RMSSD and the comprehensive security warning index SWI. On the basis of both indices, this paper proposes a security warning method and system for the safety live-line workers. The system can monitor the real-time status of workers during live-line working to provide security warning and facilitate the effective safety supervision by the live operation center during actual live-line working.

  8. An ergonomic intervention to reduce musculoskeletal discomfort among semiconductor assembly workers.

    Science.gov (United States)

    Aghilinejad, Mashallah; Azar, Neda Soleimanvandy; Ghasemi, Mohammad Sadegh; Dehghan, Naser; Mokamelkhah, Elahe Kabir

    2016-06-14

    Work-related musculoskeletal disorders (MSDs) and ergonomics-related injuries are the single largest category of workplace injuries and are responsible for almost 30% of all worker's compensation costs. Awkward working posture refers to positions of the body that deviate significantly from the neutral position while job tasks are being performed and it is the primary ergonomic risk factor for developing musculoskeletal discomfort. This study was conducted among assembly workers of a semiconductor in Tehran province with the objective of implementing an interventional ergonomic program to minimize musculoskeletal discomfort. This study that was conducted on 105 male assembly workers of a semiconductor industry based on a census method. The standardized Nordic Musculoskeletal Questionnaire (NMQ) was used to determine the prevalence of MSDs. Corlett and Bishop's body part discomfort scale (BPD) was applied to evaluate body discomfort before and after the intervention (using a magnifying loupes to improve visibility of the parts). The results of NMQ showed the highest rate of MSDs were in neck, shoulder, upper arm and lower back regions (more than 75%). After ergonomic intervention, significant decrements of discomfort was observed in neck, shoulder, upper arm, elbows, lower arm, lower back and whole body discomfort (p ergonomic interventions can decrease MSDs of at risk body regions in the long term.

  9. The Estonian study of Chernobyl cleanup workers. II. Cohort assembling and questionnaire study

    International Nuclear Information System (INIS)

    Tekkel, Mare; Rahu, Mati; Veidebaum, Toomas

    1999-01-01

    An abridged version of the published paper, Radiation Research 1997, 147, 641-652. A cohort of 4832 Chernobyl cleanup workers from Estonia was assembled. Response rate to the mailed questionnaire was 81.4%. The majority of workers were 20-39 years old, and they were less educated than their counterparts in the general population. Most of the cleanup workers were sent to the Chernobyl area in 1986-1987 and more than half of them spent about three months there. Four hundred and twenty seven cleanup workers worked on the roofs near the damaged reactor, clearing the highly radioactive debris. The most commonly performed task was removal and burial of topsoil (55% of the workers). Potassium iodide was given to over 18% of the men. (author)

  10. Simulation of Assembly Line Balancing in Automotive Component Manufacturing

    Science.gov (United States)

    Jamil, Muthanna; Mohd Razali, Noraini

    2016-02-01

    This study focuses on the simulation of assembly line balancing in an automotive component in a vendor manufacturing company. A mixed-model assembly line of charcoal canister product that is used in an engine system as fuel's vapour filter was observed and found that the current production rate of the line does not achieve customer demand even though the company practices buffer stock for two days in advance. This study was carried out by performing detailed process flow and time studies along the line. To set up a model of the line by simulation, real data was taken from a factory floor and tested for distribution fit. The data gathered was then transformed into a simulation model. After verification of the model by comparing it with the actual system, it was found that the current line efficiency is not at its optimum condition due to blockage and idle time. Various what-if analysis were applied to eliminate the cause. Proposed layout shows that the line is balanced by adding buffer to avoid the blockage. Whereas, manpower is added the stations to reduce process time therefore reducing idling time. The simulation study was carried out using ProModel software.

  11. Bucket Brigades to Increase Productivity in a Luxury Assembly Line

    Directory of Open Access Journals (Sweden)

    Filippo De Carlo

    2013-08-01

    Full Text Available One of the most challenging issues in manual assembly lines is to achieve the best balance of workloads. There are many analytic approaches to solve this problem, but they are often neglected, since they are time-consuming and require high level engineering skills. Fashion bags packaging lines must comply with a number of different products with low production volumes, while the organization of the line is often under the mere responsibility of the foreman, who balances workloads in an empirical way. The aim of this work is to evaluate the effectiveness of the arrangement of bucket brigades (BBs for an assembly line of luxury handbags. To do this, it was decided to perform a testing activity in a company producing fashion handbags in order to compare the self-made design with the BBs and with a simple assembly line balancing problem algorithm. The originality of this research lies in the fact that there are no studies in the literature on BBs applied to the packaging of highly variable small batches. The results were excellent, showing the advantages of BBs in terms of flexibility, the reduction of work in the process and the ability to handle small anomalies.

  12. Multi-objective Analysis for a Sequencing Planning of Mixed-model Assembly Line

    Science.gov (United States)

    Shimizu, Yoshiaki; Waki, Toshiya; Yoo, Jae Kyu

    Diversified customer demands are raising importance of just-in-time and agile manufacturing much more than before. Accordingly, introduction of mixed-model assembly lines becomes popular to realize the small-lot-multi-kinds production. Since it produces various kinds on the same assembly line, a rational management is of special importance. With this point of view, this study focuses on a sequencing problem of mixed-model assembly line including a paint line as its preceding process. By taking into account the paint line together, reducing work-in-process (WIP) inventory between these heterogeneous lines becomes a major concern of the sequencing problem besides improving production efficiency. Finally, we have formulated the sequencing problem as a bi-objective optimization problem to prevent various line stoppages, and to reduce the volume of WIP inventory simultaneously. Then we have proposed a practical method for the multi-objective analysis. For this purpose, we applied the weighting method to derive the Pareto front. Actually, the resulting problem is solved by a meta-heuristic method like SA (Simulated Annealing). Through numerical experiments, we verified the validity of the proposed approach, and discussed the significance of trade-off analysis between the conflicting objectives.

  13. Assembly-line health check up in digitalized hospital.

    Science.gov (United States)

    Liu, Yalan; Yao, Bin; Zhang, Zigang

    2002-01-01

    The health check up flow of digital hospital can be consulted with the assembly line of industry factory. Because they have the following same features: highly specialized workstation, closeness and continuance, rhythm, balanced production, continuous production. The essential prerequisites are as the follows: The inspecting items and methods should be stable; advanced product mix and stable production design; standardized raw material, consumption, procedure, inspection method; there are lots of request for health inspection; the customers move at the least unit; the space arrangement should be reasonable; the time arrangement should be proportion. With the computer net, the digital inspection can achieves the raw material controlling accurately. The basis of check up line concerns about equipment, net and software, data collection, and personnel. The group technology is used in the health inspection flow design of the digital hospital in the field of items customers and zone redivided. The digital assembly linemic health inspect has the following stages: member registering, notice, check in, arrange order, time control, report, feedback and analysis. The assembly linemic has following advantages: increasing the productivity, the space utility, satisfaction of customer, fund returning, lowering the cost and ensuring the quality.

  14. The LINKS motif zippers trans-acyltransferase polyketide synthase assembly lines into a biosynthetic megacomplex.

    Science.gov (United States)

    Gay, Darren C; Wagner, Drew T; Meinke, Jessica L; Zogzas, Charles E; Gay, Glen R; Keatinge-Clay, Adrian T

    2016-03-01

    Polyketides such as the clinically-valuable antibacterial agent mupirocin are constructed by architecturally-sophisticated assembly lines known as trans-acyltransferase polyketide synthases. Organelle-sized megacomplexes composed of several copies of trans-acyltransferase polyketide synthase assembly lines have been observed by others through transmission electron microscopy to be located at the Bacillus subtilis plasma membrane, where the synthesis and export of the antibacterial polyketide bacillaene takes place. In this work we analyze ten crystal structures of trans-acyltransferase polyketide synthases ketosynthase domains, seven of which are reported here for the first time, to characterize a motif capable of zippering assembly lines into a megacomplex. While each of the three-helix LINKS (Laterally-INteracting Ketosynthase Sequence) motifs is observed to similarly dock with a spatially-reversed copy of itself through hydrophobic and ionic interactions, the amino acid sequences of this motif are not conserved. Such a code is appropriate for mediating homotypic contacts between assembly lines to ensure the ordered self-assembly of a noncovalent, yet tightly-knit, enzymatic network. LINKS-mediated lateral interactions would also have the effect of bolstering the vertical association of the polypeptides that comprise a polyketide synthase assembly line. Copyright © 2015 Elsevier Inc. All rights reserved.

  15. SOLVING OPTIMAL ASSEMBLY LINE CONFIGURATION TASK BY MULTIOBJECTIVE DECISION MAKING METHODS

    Directory of Open Access Journals (Sweden)

    Ján ČABALA

    2017-06-01

    Full Text Available This paper deals with looking for the optimal configuration of automated assembly line model placed within Department of Cybernetics and Artificial Intelligence (DCAI. In order to solve this problem, Stateflow model of each configuration was created to simulate the behaviour of particular assembly line configuration. Outputs from these models were used as inputs into the multiobjective decision making process. Multi-objective decision-making methods were subsequently used to find the optimal configuration of assembly line. Paper describes the whole process of solving this task, from building the models to choosing the best configuration. Specifically, the problem was resolved using the experts’ evaluation method for evaluating the weights of every decision-making criterion, while the ELECTRE III, TOPSIS and AGREPREF methods were used for ordering the possible solutions from the most to the least suitable alternative. Obtained results were compared and final solution of this multi-objective decisionmaking problem is chosen.

  16. Engineering Mathematical Analysis Method for Productivity Rate in Linear Arrangement Serial Structure Automated Flow Assembly Line

    Directory of Open Access Journals (Sweden)

    Tan Chan Sin

    2015-01-01

    Full Text Available Productivity rate (Q or production rate is one of the important indicator criteria for industrial engineer to improve the system and finish good output in production or assembly line. Mathematical and statistical analysis method is required to be applied for productivity rate in industry visual overviews of the failure factors and further improvement within the production line especially for automated flow line since it is complicated. Mathematical model of productivity rate in linear arrangement serial structure automated flow line with different failure rate and bottleneck machining time parameters becomes the basic model for this productivity analysis. This paper presents the engineering mathematical analysis method which is applied in an automotive company which possesses automated flow assembly line in final assembly line to produce motorcycle in Malaysia. DCAS engineering and mathematical analysis method that consists of four stages known as data collection, calculation and comparison, analysis, and sustainable improvement is used to analyze productivity in automated flow assembly line based on particular mathematical model. Variety of failure rate that causes loss of productivity and bottleneck machining time is shown specifically in mathematic figure and presents the sustainable solution for productivity improvement for this final assembly automated flow line.

  17. 75 FR 22627 - Chrysler LLC, St. Louis North Assembly Plant Including On-Site Leased Workers From HAAS TCM, Inc...

    Science.gov (United States)

    2010-04-29

    ... North Assembly Plant Including On-Site Leased Workers From HAAS TCM, Inc., Logistics Services, Inc., Robinson Solutions, Logistics Management Services, Inc., Corrigan Company and Murphy Company, Fenton, MO... workers from HAAS TCM, Inc., Logistics Services, Inc., Robinson Solutions, Logistics Management Services...

  18. A multi attribute decision making method for selection of optimal assembly line

    Directory of Open Access Journals (Sweden)

    B. Vijaya Ramnath

    2011-01-01

    Full Text Available With globalization, sweeping technological development, and increasing competition, customers are placing greater demands on manufacturers to increase quality, flexibility, on time delivery of product and less cost. Therefore, manufacturers must develop and maintain a high degree of coherence among competitive priorities, order winning criteria and improvement activities. Thus, the production managers are making an attempt to transform their organization by adopting familiar and beneficial management philosophies like cellular manufacturing (CM, lean manufacturing (LM, green manufacturing (GM, total quality management (TQM, agile manufacturing (AM, and just in time manufacturing (JIT. The main objective of this paper is to propose an optimal assembly method for an engine manufacturer’s assembly line in India. Currently, the Indian manufacturer is following traditional assembly method where the raw materials for assembly are kept along the sideways of conveyor line. It consumes more floor space, more work in process inventory, more operator's walking time and more operator's walking distance per day. In order to reduce the above mentioned wastes, lean kitting assembly is suggested by some managers. Another group of managers suggest JIT assembly as it consumes very less inventory cost compared to other types of assembly processes. Hence, a Multi-attribute decision making model namely analytical hierarchy process (AHP is applied to analyse the alternative assembly methods based on various important factors.

  19. Statistical Methods in Assembly Quality Management of Multi-Element Products on Automatic Rotor Lines

    Science.gov (United States)

    Pries, V. V.; Proskuriakov, N. E.

    2018-04-01

    To control the assembly quality of multi-element mass-produced products on automatic rotor lines, control methods with operational feedback are required. However, due to possible failures in the operation of the devices and systems of automatic rotor line, there is always a real probability of getting defective (incomplete) products into the output process stream. Therefore, a continuous sampling control of the products completeness, based on the use of statistical methods, remains an important element in managing the quality of assembly of multi-element mass products on automatic rotor lines. The feature of continuous sampling control of the multi-element products completeness in the assembly process is its breaking sort, which excludes the possibility of returning component parts after sampling control to the process stream and leads to a decrease in the actual productivity of the assembly equipment. Therefore, the use of statistical procedures for continuous sampling control of the multi-element products completeness when assembled on automatic rotor lines requires the use of such sampling plans that ensure a minimum size of control samples. Comparison of the values of the limit of the average output defect level for the continuous sampling plan (CSP) and for the automated continuous sampling plan (ACSP) shows the possibility of providing lower limit values for the average output defects level using the ACSP-1. Also, the average sample size when using the ACSP-1 plan is less than when using the CSP-1 plan. Thus, the application of statistical methods in the assembly quality management of multi-element products on automatic rotor lines, involving the use of proposed plans and methods for continuous selective control, will allow to automating sampling control procedures and the required level of quality of assembled products while minimizing sample size.

  20. Ergonomic risk assessment with DesignCheck to evaluate assembly work in different phases of the vehicle development process.

    Science.gov (United States)

    Winter, Gabriele; Schaub, Karlheinz G; Großmann, Kay; Laun, Gerhard; Landau, Kurt; Bruder, Ralph

    2012-01-01

    Occupational hazards exist, if the design of the work situation is not in accordance with ergonomic design principles. At assembly lines ergonomics is applied to the design of work equipment and tasks and to work organisation. The ignoring of ergonomic principles in planning and design of assembly work leads to unfavourable working posture, action force and material handling. Disorders of the musculoskeletal system are of a common occurrence throughout Europe. Musculoskeletal disorders are a challenge against the background of disabled workers. The changes in a worker's capability have to be regarded in the conception of redesigned and new assembly lines. In this way ergonomics becomes progressively more important in planning and design of vehicles: The objective of ergonomic design in different stages of the vehicles development process is to achieve an optimal adaptation of the assembly work to workers. Hence the ergonomic screening tool "Design Check" (DC) was developed to identify ergonomic deficits in workplace layouts. The screening-tool is based on the current ergonomic state of the art in the design of physical work and relevant EU legal requirements. It was tested within a federal German research project at selected work stations at the assembly lines at Dr.-Ing. h.c. F. Porsche AG / Stuttgart. Meanwhile the application of the screening-tool DC is transferred in other parts of the Porsche AG, Stuttgart. It is also realized as an ergonomic standard method to perform assembly work in different phases of the vehicle development process.

  1. REDUCTION OF CYCLE TIME IN SCREW AIR COMPRESSOR ASSEMBLY LINE USING KAIZEN SURVEY

    Directory of Open Access Journals (Sweden)

    D. Rajenthirakumar

    2015-12-01

    Full Text Available In this competitive world, any company has to fulfill its customer needs to survive in the market. Lean manufacturing is a technique that can be adopted in a company to improve the quality of its products, reduce the cost of the production and also deliver the products in less time. The goal of this work is to show the applicability of lean manufacturing’s body of knowledge in a screw air compressor manufacturing company. Here, the main objective is to evolve and test several methodologies to eliminate wastes in the assembly line as the company at present unable to meet the customer demand. A systematic approach is suggested for the implementation of lean principles to showcase that lean could be applied to the compressor assembly line to enhance the productivity thereby making the line more efficient. In the current assembly line there was no work standardization followed by absence of kaizen that has led to an increased assembly time. Thus with the help of lean tools and techniques such as 5S, kaizen, standardization, visual management, poke yoke and string diagram the total cycle time has been reduced from 236 to 209 minutes. This reduction has benefitted the company in meeting the customer demand, increased profit and work satisfaction.

  2. Bucket Brigades to Increase Productivity in a Luxury Assembly Line

    OpenAIRE

    Carlo, Filippo De; Borgia, Orlando; Tucci, Mario

    2013-01-01

    One of the most challenging issues in manual assembly lines is to achieve the best balance of workloads. There are many analytic approaches to solve this problem, but they are often neglected, since they are time-consuming and require high level engineering skills. Fashion bags packaging lines must comply with a number of different products with low production volumes, while the organization of the line is often under the mere responsibility of the foreman, who balances workloads in an empiri...

  3. Self-perceived depression, anxiety, stress and their relationships with psychosocial job factors in male automotive assembly workers.

    Science.gov (United States)

    Edimansyah, Bin Abdin; Rusli, Bin Nordin; Naing, Lin; Mohamed Rusli, Bin Abdullah; Winn, Than; Tengku Mohamed Ariff, Bin Raja Hussin

    2008-01-01

    Depression, anxiety and stress have been recognized as important mental outcome measures in stressful working settings. The present study explores the prevalence of self-perceived depression, anxiety and stress; and their relationships with psychosocial job factors. A cross-sectional study involving 728 male automotive assembly workers was conducted in two major automotive assembly plants in Malaysia using the validated Malay versions of the Depression Anxiety Stress Scales (DASS) and Job Content Questionnaire (JCQ). Based on the DASS cut-off of > or =78 percentile scores, the prevalence of self-perceived depression, anxiety and stress was 35.4%, 47.2% and 31.1%, respectively. Four (0.5%), 29 (4.0%) and 2 (0.3%) workers, respectively, reported extremely severe self-perceived depression, anxiety and stress. Multiple linear regression analyses, controlling for age, education, salary, duration of work and marital status, revealed that psychological job demand, job insecurity and hazardous condition were positively associated with DASS-Depression, DASS-Anxiety and DASS-Stress; supervisor support was inversely associated with DASS-Depression and DASS-Stress. We suggest that reducing psychological job demand, job insecurity and hazardous condition factors may improve the self-perceived depression, anxiety and stress in male automotive assembly workers. Supervisor support is protective for self-perceived depression and stress.

  4. [Personality and occupation stress of workers in processing line in Guangzhou].

    Science.gov (United States)

    Lin, Qiu-hong; Zhang, Wei-sen; Zhou, Jing-dong; Fan, Yuan-yu; Liu, Li-fen; Li, Jian-lin; Liu, Wei-wei

    2009-12-01

    To study relationships between personality and occupational stress of workers in processing line in Guangzhou. 452 workers in processing line in Guangzhou were investigated by the Eysenck Personality Questionnaire (EPQ) and Occupational Stress Indicator (OSI). N scores and P scores of EPQ were positively correlated with the occupational stress and the poor physical fitness status (r value was 0.196, 0.128, 0.202, 0.218, respectively) (P stress coping ability(r value was -0.146, -0.140, respectively) (P stress coping ability (r = 0.176, P stress, the poor physical fitness status and the explanation to vicinity event (r value was -0.139, -0.140, -0.111, respectively) (P related to the occupational stress, the sense of job satisfaction and unhealthy mental reaction.

  5. A protein interaction map of the kalimantacin biosynthesis assembly line

    Directory of Open Access Journals (Sweden)

    Birgit Uytterhoeven

    2016-11-01

    Full Text Available The antimicrobial secondary metabolite kalimantacin is produced by a hybrid polyketide/ non-ribosomal peptide system in Pseudomonas fluorescens BCCM_ID9359. In this study, the kalimantacin biosynthesis gene cluster is analyzed by yeast two-hybrid analysis, creating a protein-protein interaction map of the entire assembly line. In total, 28 potential interactions were identified, of which 13 could be confirmed further. These interactions include the dimerization of ketosynthase domains, a link between assembly line modules 9 and 10, and a specific interaction between the trans-acting enoyl reductase BatK and the carrier proteins of modules 8 and 10. These interactions reveal fundamental insight into the biosynthesis of secondary metabolites.This study is the first to reveal interactions in a complete biosynthetic pathway. Similar future studies could build a strong basis for engineering strategies in such clusters.

  6. Relationship of psychosocial work factors and health-related quality of life in male automotive assembly workers in Malaysia.

    Science.gov (United States)

    Edimansyah, Bin Abdin; Rusli, Bin Nordin; Naing, Lin; Mohamed Rusli, Bin Abdullah; Winn, Than

    2007-06-01

    The present study investigates the relationship between psychosocial work factors and health-related quality of life (HRQOL) in male automotive assembly plant workers in Malaysia. A total of 728 male workers were recruited in March-July 2005 from 2 major automotive assembly plants in Selangor and Pahang. In this cross-sectional study, information on socio-demography, psychosocial work factors using the 97-item Job Content Questionnaire (JCQ) and an abbreviated 26-item version of the World Health Organization Quality of Life-Brief Version (WHOQOL-BREF) questionnaire containing 4 domains (physical health, psychological, social relationship, and environment) was self-administered to all workers involved. The prevalence of reported good or very good overall HRQOL and general health was 64.9% and 53.7%, respectively. Multiple linear regression analysis indicated that created skill was positively associated with physical health and psychological domains; whilst, skill discretion was positively associated with social relationship and environment domains. Social support was positively associated with physical health and environment domains; whilst, co-worker support was positively associated with psychological and social relationship domains. Job insecurity and hazardous condition were negatively associated with all domains, whilst psychological job demands was negatively associated with the environment domain of HRQOL.

  7. Job Satisfaction and Its Influential Factors in Assembly Line Workers%流水线作业工人工作满意感及其影响因素

    Institute of Scientific and Technical Information of China (English)

    王芳芳; 余善法

    2011-01-01

    目的 探讨流水线作业工人工作满意感与职业应激相关因素的关系.方法采取整群抽样方法对某电器厂流水线178名作业工人进行调查.使用问卷调查人口统计学特征、工作满意感、职业紧张因素、身心健康状况和个性特征.结果 t检验结果显示,初中文化程度者的工作满意感评分比高中及以上文化程度者均较高,工龄≤1.75 a的工人比工龄1.75 a的工人工作满意感得分高,差异有统计学意义(P<0.05).协方差分析结果显示,工作满意感高水平组工作心理需求、工作躯体需求、外在付出、工作心理控制源、抑郁症状、每日紧张感评分低于低水平组,而上级支持、回报、决策自由度、提升机会、组织忠诚度、情绪平衡评分高于低水平组,差异有统计学意义(P<0.05或P<0.01).pearson相关结果显示,工作满意感与工作心理需求、外在付出、工作心理控制源、抑郁症状、每日紧张感呈负相关(P<0.01),与上级支持、同事支持、回报、组织忠诚度、心理卫生、情绪平衡呈正相关(P<0.05或P<0.01).多因素logistic回归结果表明,文化程度与工作满意感有关,上级支持(OR=0.24)、回报(OR=0.25)、情绪平衡(OR=0.31)、组织忠诚度(OR=0.39)是工作满意感的保护因素.结论 文化程度、工龄、职业应激相关因素对工作满意感有较大影响.%Objective To explore the correlation between the job satisfaction and related factors of occupational stress in assembly line workers. Methods 178 assembly line workers were investigated by group sampling method. The questionnaire used in investigation included demographics, job satisfaction,occupational stressors, physical and mental health status, and personalities. Results 1) t tests showed that the job satisfaction scores of workers with junior high school education were higher than those with high school education; the workers with working age≤ 1.75 years had higher job

  8. An Assembly Line Balancing Problem Automotive Cables

    Directory of Open Access Journals (Sweden)

    Triki Hager

    2015-02-01

    Full Text Available In this paper, an Assembly Line Balancing Problem (ALBP is presented in a real-world automotive cables manufacturer company. This company found it necessary to balance its line, since it needs to increase the production rate. In this ALBP, the number of stations is known and the objective is to minimize cycle time where both precedence and zoning constrains must be satisfied. This problem is formulated as a binary linear program (BLP. Since this problem is NP-hard, an innovative Genetic Algorithm (GA is implemented. The full factorial design is used to obtain the better combination GA parameters and a simple convergence experimental study is performed on the stopping criteria to reduce computational time. Comparison of the proposed GA results with CPLEX software shows that, in a reasonable time, the GA generates consistent solutions that are very close to their optimal ones. Therefore, the proposed GA approach is very effective and competitive.

  9. A biomonitoring study of genotoxic risk to workers of transformers and distribution line stations.

    Science.gov (United States)

    Celikler, Serap; Aydemir, Nilufer; Vatan, Ozgur; Kurtuldu, Sevim; Bilaloglu, Rahmi

    2009-12-01

    A cytogenetic monitoring study was carried out on a group of workers from transformer and distribution line stations in the Bursa province of Turkey, to investigate the genotoxic risk of occupational exposure to extremely low frequency electric (ELF) and magnetic fields (EMF). Cytogenetic analysis, namely chromosomal aberrations (CAs) and micronucleus (MN) tests were performed on a strictly selected group of 55 workers and compared to 17 controls. CA and MN frequencies in electrical workers appeared significantly higher than in controls (p electric transformer and distribution stations.

  10. Model for Assembly Line Re-Balancing Considering Additional Capacity and Outsourcing to Face Demand Fluctuations

    Science.gov (United States)

    Samadhi, TMAA; Sumihartati, Atin

    2016-02-01

    The most critical stage in a garment industry is sewing process, because generally, it consists of a number of operations and a large number of sewing machines for each operation. Therefore, it requires a balancing method that can assign task to work station with balance workloads. Many studies on assembly line balancing assume a new assembly line, but in reality, due to demand fluctuation and demand increased a re-balancing is needed. To cope with those fluctuating demand changes, additional capacity can be carried out by investing in spare sewing machine and paying for sewing service through outsourcing. This study develops an assembly line balancing (ALB) model on existing line to cope with fluctuating demand change. Capacity redesign is decided if the fluctuation demand exceeds the available capacity through a combination of making investment on new machines and outsourcing while considering for minimizing the cost of idle capacity in the future. The objective of the model is to minimize the total cost of the line assembly that consists of operating costs, machine cost, adding capacity cost, losses cost due to idle capacity and outsourcing costs. The model develop is based on an integer programming model. The model is tested for a set of data of one year demand with the existing number of sewing machines of 41 units. The result shows that additional maximum capacity up to 76 units of machine required when there is an increase of 60% of the average demand, at the equal cost parameters..

  11. Comprehensive evaluation of garment assembly line with simulation

    Science.gov (United States)

    Xu, Y.; Thomassey, S.; Chen, Y.; Zeng, X.

    2017-10-01

    In this paper, a comprehensive evaluation system is established to assess the garment production performance. It is based on performance indicators and supported with the corresponding results obtained by manual calculation or computer simulation. The assembly lines of a typical men’s shirt are taken as the study objects. With the comprehensive evaluation results, garments production arrangement scenarios are better analysed and then the appropriate one is supposed to be put into actual production. This will be a guidance given to companies on quick decision-making and multi-objective optimization of garment production.

  12. Advantages and Disadvantages of Possible Methods of Managing the Production on the Assembly Lines in the Given Company

    OpenAIRE

    Václavková, Eva

    2014-01-01

    The bachelor thesis deals with methods of lean management, more exactly production planning and managing the production lines assembly. In this thesis, production planning system, kanban cards and heijunka will be described. The aim of this thesis is to describe methods of managing the production lines assembly and to suggest more effective management.

  13. Assembly Line Efficiency Improvement by Using WITNESS Simulation Software

    Science.gov (United States)

    Yasir, A. S. H. M.; Mohamed, N. M. Z. N.

    2018-03-01

    In the nowadays-competitive world, efficiencies and the productivity of the assembly line are essential in manufacturing company. This paper demonstrates the study of the existing production line performance. The actual cycle time observed and recorded during the working process. The current layout was designed and analysed using Witness simulation software. The productivity and effectiveness for every single operator are measured to determine the operator idle time and busy time. Two new alternatives layout were proposed and analysed by using Witness simulation software to improve the performance of production activities. This research provided valuable and better understanding of production effectiveness by adjusting the line balancing. After analysing the data, simulation result from the current layout and the proposed plan later been tabulated to compare the improved efficiency and productivity. The proposed design plan has shown an increase in yield and productivity compared to the current arrangement. This research has been carried out in company XYZ, which is one of the automotive premises in Pahang, Malaysia.

  14. Car Assembly Line Efficiency Improvement by Lean Principle

    Science.gov (United States)

    Sawassalung, Suwalee; Chutima, Parames

    2017-06-01

    This research aimed to increase the efficiency of actual working time to compare to design standard time ratio (DSTR) as per analysing process of Lean System of the assembly line in a car manufacturer in Thailand. Currently, the case study factory and its group of factories, which have many branches all over the world, have competed with each other on quality, delivered time and production cost. The production cost which can reduce without affecting quality and acceptable by clients is the manpower cost. The index of competition is DSTR. The factory now has DSTR of 6.13 and DSTR of the assembly department is 4.24 which is very high comparing to other departments. The low DSTR indicates that the factory has good quality. The ways to solve the problem are to apply the following tools, i.e. Lean principle, Value Stream Mapping (VSM), Waste Analysis and ECRS. After implementing the above tools, the results showed that DSTR decreased from 4.24 to 4.06 or 4.25%.

  15. America's Assembly Line

    DEFF Research Database (Denmark)

    Nye, David Edwin

    and provoked strikes and union drives in the 1930s, but became a symbol of victory in the Second World War and Cold War. Reinvented by Japan as "lean production" and then increasingly automated after 1990, it remains a cornerstone of production but no longer employs many workers, even as it evolves toward...

  16. America's Assembly Line

    DEFF Research Database (Denmark)

    Nye, David Edwin

    and provoked strikes and union drives in the 1930s, but became a symbol of victory in the Second World War and Cold War. Reinvented by Japan as "lean production" and then increasingly automated after 1990, it remains a cornerstone of production but no longer employs many workers, even as it evolves toward...... sustainable manufacturing....

  17. Poverty, Place and Pedagogy in Education: Research Stories from Front-Line Workers

    Science.gov (United States)

    Comber, Barbara

    2016-01-01

    This article considers what it means to teach and learn in places of poverty through the narratives of front-line workers--particularly students and teachers. What is the work of teaching and learning in places of poverty in current times? How has this changed? What can be learned from both the haunting and hopeful narratives of front-line…

  18. Participatory ergonomics and new work: reducing neck complaints in assembling.

    Science.gov (United States)

    Miguez, S A; Hallbeck, M S; Vink, P

    2012-01-01

    A participatory ergonomics approach is used to create a new work environment, which is aimed at reducing neck complaints in a cell phone assembly. The participatory ergonomics program included an initiative, problem identification, a selection of solutions, an implementation and evaluation. Twenty-eight women, all operators on an assembly line of cell phone boards, voluntarily participated in the design and evaluation of a device before implementing the device to all 215 employees performing that job. Prior to and after the intervention, RULA, comfort experiences and interviews were used. After introducing an adjustable angled small counter, these measurements showed both posture and comfort improvements. 90% of the 215 workers preferred the new work station and the neck complaints were reduced in 75% of the group. It also showed that the initial prototype needed to be modified as to reduce its sharp edges/compression points for the forearm. This project shows the importance of iterative testing and that an initiative by workers enlarges the chance of successful implementation.

  19. Supplying of Assembly Lines Using Train of Trucks

    Science.gov (United States)

    Čujan, Zdeněk; Fedorko, Gabriel

    2016-11-01

    The typical supply system conceptions, i.e. the concepts "Just-in-time" (JIT) and "Just-in-sequence" (JIS) are very important factors with regard to a fluent operation of the assembly lines. Therefore the contemporary intra plant transport systems are being replaced by a new kind of the transportation technology, namely by means of the trains of trucks. The trains of trucks are used in two possible operational modes: either with a driver or without driver (fully automated). The trucks of the logistic trains are also cheaper and they are able to carry a larger volume and mass of the material at once. There are reduced in this way not only the investment costs, but also the operational expenses.

  20. The Influencing Factor Analysis on the Performance Evaluation of Assembly Line Balancing Problem Level 1 (SALBP-1) Based on ANOVA Method

    Science.gov (United States)

    Chen, Jie; Hu, Jiangnan

    2017-06-01

    Industry 4.0 and lean production has become the focus of manufacturing. A current issue is to analyse the performance of the assembly line balancing. This study focus on distinguishing the factors influencing the assembly line balancing. The one-way ANOVA method is applied to explore the significant degree of distinguished factors. And regression model is built to find key points. The maximal task time (tmax ), the quantity of tasks (n), and degree of convergence of precedence graph (conv) are critical for the performance of assembly line balancing. The conclusion will do a favor to the lean production in the manufacturing.

  1. MILP for the Inventory and Routing for Replenishment Problem in the Car Assembly Line.

    Directory of Open Access Journals (Sweden)

    Raul Pulido

    2014-01-01

    Full Text Available The inbound logistic for feeding the workstation inside the factory represents a critical issue in the car manufacturing industry. Nowadays, this issue is even more critical than in the past since more types of car are being produced in the assembly lines. Consequently, as workstations have to install many types of components, they also need to have an inventory of different types of the component in a compact space.The replenishment is a critical issue since a lack of inventory could cause line stoppage or reworking. On the other hand, an excess of inventory could increase the holding cost or even block the replenishment paths. The decision of the replenishment routes cannot be made without taking into consideration the inventory needed by each station during the production time which will depend on the production sequence. This problem deals with medium-sized instances and it is solved using online solvers. The contribution of this paper is a MILP for the replenishment and inventory of the components in a car assembly line.

  2. Participatory ergonomic intervention for prevention of low back pain: assembly line redesign case.

    Science.gov (United States)

    Bernardes, João Marcos; Wanderck, Claudia; Moro, Antônio Renato Pereira

    2012-01-01

    This paper gives an overview of a participatory ergonomic intervention aimed at reducing low back pain cases in the dispatch department of a catalogue and e-commerce retail company. Based on the findings of the ergonomic analysis and design committee, the company's own employees redesigned the assembly line's layout. As a result of these changes two job tasks that involved manual material handling of boxes, identified by the revised NIOSH equation as posing an increased risk for lifting-related low back pain, were totally eliminated, and the employees responsible for moving boxes from the end of the assembly line to pallets on the ground were given more control over their jobs, and these jobs were also enriched with a new, less heavy task. These results demonstrate that participatory ergonomic interventions are a viable and effective strategy to reduce the exposure to work-related physical and psychosocial risk factors for low back pain.

  3. EVALUATION OF ASSEMBLY LINE BALANCING METHODS USING AN ANALYTICAL HIERARCHY PROCESS (AHP AND TECHNIQUE FOR ORDER PREFERENCES BY SIMILARITY TO IDEAL SOLUTION (TOPSIS BASED APPROACH

    Directory of Open Access Journals (Sweden)

    Pallavi Sharma

    2013-12-01

    Full Text Available Assembly lines are special flow-line production systems which are of great importance in the industrial production of high quantity standardized commodities. In this article, assembly line balancing problem is formulated as a multi objective (criteria problem where four easily quantifiable objectives (criteria's are defined. Objectives (criteria's included are line efficiency, balance delay, smoothness index, and line time. And the value of these objectives is calculated by five different heuristics. In this paper, focus is made on the prioritization of assembly line balancing (ALB solution methods (heuristics and to select the best of them. For this purpose, a bench mark assembly line balancing problem is solved by five different heuristics and the value of objectives criteria's (performance measures of the line is determined. Finally the prioritization of heuristics is carried out through the use of AHP-TOPSIS based approach by solving an example.

  4. Multi-objective optimization algorithms for mixed model assembly line balancing problem with parallel workstations

    Directory of Open Access Journals (Sweden)

    Masoud Rabbani

    2016-12-01

    Full Text Available This paper deals with mixed model assembly line (MMAL balancing problem of type-I. In MMALs several products are made on an assembly line while the similarity of these products is so high. As a result, it is possible to assemble several types of products simultaneously without any additional setup times. The problem has some particular features such as parallel workstations and precedence constraints in dynamic periods in which each period also effects on its next period. The research intends to reduce the number of workstations and maximize the workload smoothness between workstations. Dynamic periods are used to determine all variables in different periods to achieve efficient solutions. A non-dominated sorting genetic algorithm (NSGA-II and multi-objective particle swarm optimization (MOPSO are used to solve the problem. The proposed model is validated with GAMS software for small size problem and the performance of the foregoing algorithms is compared with each other based on some comparison metrics. The NSGA-II outperforms MOPSO with respect to some comparison metrics used in this paper, but in other metrics MOPSO is better than NSGA-II. Finally, conclusion and future research is provided.

  5. A Review of Related Work on Machine Learning in Semiconductor Manufacturing and Assembly Lines

    OpenAIRE

    Stanisavljevic, Darko; Spitzer, Michael

    2017-01-01

    This paper deals with applications of machine learning algorithms in manufacturing. Machine learning can be defined as a field of computer science that gives computers the ability to learn without explicitly developing the needed algorithms. Manufacturing is the production of merchandise by manual labour, machines and tools. The focus of this paper is on automatic production lines. The areas of interest of this paper are semiconductor manufacturing and production on assembly lines. The purpos...

  6. The evaluation of radiation level and dose of workers in Guangzhou metro line 1

    International Nuclear Information System (INIS)

    Zhang Lin; Hu Canyun; Meng Xiaolian; He Zhan

    2006-01-01

    Objective: To find out the level of radiation and effective dose of workers in Guangzhou Metro line 1. Methods: In metro stations, external Gamma-ray exposure rates were obtained by FD-71A radiance measurer, 222 Rn and 220 Rn concentrations were obtained by using Rn-Tn solid state nuclear track detectors developed by The National Institute for Radiological Protection and Nuclear Safety, Chinese Centre for Disease Control. The annual Effective dose from Gamma, 222 Rn and 220 Rn were calculated. Results: The external Gamma-ray exposure average rate is 17.74 x 10 -8 Gy/h. The average concentration of 222 Rn is 59.8 Bq/m 3 . The average concentration of 220 Rn is 32.1 Bq/m 3 . The total annual effective dose from Gamma, 222 Rn and 220 Rn is 2.878 mSv/a. Conclusion: In the stations of Guangzhou in metro line 1, no more effective radiation dose to the workers has measured. (authors)

  7. Statistical evaluation of the on line core monitoring effectiveness for limiting the consequences of the fuel assembly misloading event

    International Nuclear Information System (INIS)

    Molnar, A.; Kereszturi, A.; Temesvari, E.; Korpas, L.

    2007-01-01

    In WWER-440 type reactors, on line core monitoring is used for the early indication of such abnormal events like fuel assembly misloading, inadvertent misalignment of Control Assemblies, blockage of coolant channels. The paper is focusing on the assembly misloading, which can not be indicated by other measurements. A Monte Carlo method was developed and applied to evaluate the on line core monitoring effectiveness for the indication of this abnormal event during the power increase in due time, when the consequences are still acceptable. The investigations proved the satisfactory effectiveness of the online core monitoring down to 55 % power even in case when 75 % of the temperature measurements was only available (Authors)

  8. Heuristic for Task-Worker Assignment with Varying Learning Slopes

    Directory of Open Access Journals (Sweden)

    Wipawee Tharmmaphornphilas

    2010-04-01

    Full Text Available Fashion industry has variety products, so the multi-skilled workers are required to improve flexibility in production and assignment. Generally the supervisor will assign task to the workers based on skill and skill levels of worker. Since in fashion industry new product styles are launched more frequently and the order size tends to be smaller, the workers always learn when the raw material and the production process changes. Consequently they require less time to produce the succeeding units of a task based on their learning ability. Since the workers have both experience and inexperience workers, so each worker has different skill level and learning ability. Consequently, the assignment which assumed constant skill level is not proper to use. This paper proposes a task-worker assignment considering worker skill levels and learning abilities. Processing time of each worker changes along production period due to a worker learning ability. We focus on a task-worker assignment in a fashion industry where tasks are ordered in series; the number of tasks is greater than the number of workers. Therefore, workers can perform multiple assignments followed the precedence restriction as an assembly line balancing problem. The problem is formulated in an integer linear programming model with objective to minimize makespan. A heuristic is proposed to determine the lower bound (LB and the upper bound (UB of the problem and the best assignment is determined. The performance of the heuristic method is tested by comparing quality of solution and computational time to optimal solutions.

  9. Operational experience with the GEM detector assembly lines for the CMS forward muon upgrade

    CERN Document Server

    Vai, Ilaria

    2017-01-01

    The CMS Collaboration has been developing large-area Triple-GEM detectors to be installed in the muon endcap regions of the CMS experiment in 2019 to maintain forward muon trigger and tracking performance at the HL-LHC. Ten pre-production detectors were built at CERN to commission the first assembly line and the quality controls. These were installed in the CMS detector in early 2017 and are currently participating in the 2017 LHC run. The collaboration has prepared several additional assembly and quality control lines for distributed mass production of 160 GEM detectors at various sites worldwide. During 2017, these additional production sites have been optimizing construction techniques and quality control procedures and validating them against common specifications by constructing additional pre-production detectors. Using the specific experience from one production site as an example, we discuss how the quality controls make use of independent hardware and trained personnel to ensure fast and reliable pro...

  10. The Design of a Molecular Assembly Line Based on Biological Molecules

    Science.gov (United States)

    2003-06-01

    parenthesis in figure 1.8 is a bi-stable toggle switch. Introduction: Molecular assembly lines O=P-O- O O HOH H0P-0- O -O- 4 Polymerase HO H--- O HHO ...sample. Therefore, the samples are self-consistent. From here on, the calculated temperature based on FAM emission MNSowmm" RF Biology: Results and...irradiation for one hour. Figure 2.11 shows the fluorescence spectra of FAM emission (4 scans averaged over 200 seconds) in a 300MHz field. The increased

  11. ANALYSIS AND IMPROVEMENT OF PRODUCTION EFFICIENCY IN A CONSTRUCTION MACHINE ASSEMBLY LINE

    Directory of Open Access Journals (Sweden)

    Alidiane Xavier

    2016-07-01

    Full Text Available The increased competitiveness in the market encourages the ongoing development of systems and production processes. The aim is to increase production efficiency to production costs and waste be reduced to the extreme, allowing an increased product competitiveness. The objective of this study was to analyze the overall results of implementing a Kaizen philosophy in an automaker of construction machinery, using the methodology of action research, which will be studied in situ the macro production process from receipt of parts into the end of the assembly line , prioritizing the analysis time of shipping and handling. The results show that the continuous improvement activities directly impact the elimination of waste from the assembly process, mainly related to shipping and handling, improving production efficiency by 30% in the studied processes.

  12. Peculiarities of Social Insurance of Workers of the Middle Volga Steamship Line During the Post-War Restoration Period (1945-1946

    Directory of Open Access Journals (Sweden)

    Gomanenko Olesya Aleksandrovna

    2015-11-01

    Full Text Available During the post-war restoration the work on social insurance in river transport was intensified. It were trade unions including councils of social insurance that dealt with social problems in the Volga Steamship Lines. Trade unions exercised control over the budget of social insurance, over labor safety, etc. In the Middle Volga Steamship Line (SVRP 15 councils for social insurance functioned. They included 140 insurance agents. Their task was to decrease incidence, traumatism, and also to improve the conditions of work and life of river transport workers. Tasks of councils of a social insurance included systematic supervision over a sanitary condition of shops and territories of the industrial enterprises of the steamship line. Financial support was allocated to families of veterans with many children and families in need. Insurance delegates together with a doctor of the health center in workshops registered workers needing additional food for health reasons. Insurance delegates gave social help to patients at home and in hospital. After the end of the war comprehensive plans of improving actions were put through. Financial and food position of river transport workers improved. However in 1946 in SVRP there was a small growth of incidence again. Those who needed treatment, and also the best workers were provided with permits in sanatorium. Managements of Volga Steamship lines showed care of children of river transport workers. During thewinter period camps were decorated with New Year trees, in summer – rest was arranged. On the accounting of the trade-union organizations of the Middle Volga basin families of the lost soldiers, the military personnel, disabled veterans and demobilized consisted. As for labor protection, that, despite increase in allocations for safety measures and labor protection in 1946 at the SVRP enterprises occurred increase in accidents. So, all efforts were directed on further improvement of financial and social

  13. Transfer of fuel assemblies

    International Nuclear Information System (INIS)

    Vuckovich, M.; Burkett, J. P.; Sallustio, J.

    1984-01-01

    Fuel assemblies of a nuclear reactor are transferred during fueling or refueling or the like by a crane. The work-engaging fixture of the crane picks up an assembly, removes it from this slot, transfers it to the deposit site and deposits it in its slot at the deposit site. The control for the crane includes a strain gauge connected to the crane line which raises and lowers the load. The strain gauge senses the load on the crane. The signal from the strain gauge is compared with setpoints; a high-level setpoint, a low-level setpoint and a slack-line setpoint. If the strain gauge signal exceeds the high-level setpoint, the line drive is disabled. This event may occur during raising of a fuel assembly which encounters resistance. The high-level setpoint may be overridden under proper precautions. The line drive is also disabled if the strain gauge signal is less than the low-level setpoint. This event occurs when a fuel assembly being deposited contacts the bottom of its slot or an obstruction in, or at the entry to the slot. To preclude lateral movement and possible damage to a fuel assembly suspended from the crane line, the traverse drive of the crane is disabled once the strain-gauge exceets the lov-level setpoint. The traverse drive can only be enabled after the strain-gauge signal is less than the slack-line set-point. This occurs when the lines has been set in slack-line setting. When the line is tensioned after slack-li ne setting, the traverse drive remains enabled only if the line has been disconnected from the fuel assembly

  14. Material flow enhancement in production assembly lines under application of zoned order picking systems

    Directory of Open Access Journals (Sweden)

    D. Živanić

    2014-10-01

    Full Text Available Introduced research work relates to the possibility of material flow enhancement in production systems, with the apostrophe on material order picking in production assembly lines. The paper presents basic rules and the results related to formed computer models of zoned order picking systems under the application of developed bound cavities method.

  15. On-line system for monitoring of boiling in nuclear reactor fuel assemblies

    International Nuclear Information System (INIS)

    Tuerkcan, E.; Kozma, R.; Verhoef, J.P.; Nabeshima, K.

    1996-01-01

    An important goal of nuclear reactor instrumentation is the continuous monitoring of the state of the reactor and the detection of deviations from the normal behaviour at an early stage. Early detection of anomalies enables one to make the necessary steps in order to prevent further damage of nuclear fuel. In the present paper, an on-line core monitoring system is described by means of which boiling anomaly in nuclear reactor fuel assemblies can be detected. (author). 9 refs, 7 figs

  16. An analysis of fast reactor fuel assembly performance taking into account their mechanical interaction in the core and refuelling line capabilities

    International Nuclear Information System (INIS)

    Buksha, Yu.K.; Zabudko, L.M.; Kravchenko, I.N.; Matveenko, L.V.; Meshkov, M.N.

    1984-01-01

    An approach to assessment of fast reactor fuel assembly performance has been considered. A concept of passive restraint of fuel assemblies in a reactor adopted in the USSR is described. Some methods for calculating the interassembly interactions during operation are briefly outlined, some calculated results are presented. A problem of fuel assembly performance during refuelling taking into account the refuelling line capabilities is considered. Some results from fuel assemblies operation experience in the BN-600 reactor are given. (author)

  17. Workload analyse of assembling process

    Science.gov (United States)

    Ghenghea, L. D.

    2015-11-01

    The workload is the most important indicator for managers responsible of industrial technological processes no matter if these are automated, mechanized or simply manual in each case, machines or workers will be in the focus of workload measurements. The paper deals with workload analyses made to a most part manual assembling technology for roller bearings assembling process, executed in a big company, with integrated bearings manufacturing processes. In this analyses the delay sample technique have been used to identify and divide all bearing assemblers activities, to get information about time parts from 480 minutes day work time that workers allow to each activity. The developed study shows some ways to increase the process productivity without supplementary investments and also indicated the process automation could be the solution to gain maximum productivity.

  18. Stress fractures of the rib arising from the manufactory assembly line

    International Nuclear Information System (INIS)

    Arima, Toru; Iwasaki, Masayuki

    2007-01-01

    We investigated stress injuries of the rib arising from the assembly line. The patients, all males, were 20 in number and divided into two groups; those with stress fracture (n=13) and those with ''pre-fracture'' (n=7). The former group with the average age of 37 years was involved by a single fracture in 10 patients and multiple fractures in 3, ranging from 5th to 8th ribs, with the affected side on the right in 9 and the left in 4. All 13 fractures occurred in the posterior half of the rib, in which 5 were located in its lateral portion, 5 in the middle, and 3 in the posterior. The latter group with the average age of 32 years were involved on the right side in 4 and the left in 3. The working pattern causing rib injuries was either repeated raising of the upper extremity or forward pushing of the shoulder girdle. The symptom was back pain, and aggravated especially in elevation of the arm, deep breathing and sneezing. Local tenderness over the fracture site was noted in all cases. X-ray findings at initial examination revealed fractures in most cases and 3D-CT was employed in 9 questionable cases to assess fracture conditions. In the ''pre-fracture'' group, although the fracture was not recognized on X-ray, the diagnosis was made as an impending fracture based on the localized tenderness on the rib. As to treatment, bust band fixation and work load reduction were performed. Stress fractures of the rib have been occasionally reported in sports medicine, but not so much in industrial medicine. This specific injury has been treated in literature as muscle strain because of the absence of apparent trauma. It is important to recognize the underlying pathology to make the correct diagnosis. In the early stage of rib fractures, 3D-CT was more useful than X-ray in making diagnosis and assessing the bony union. As to the pathomechanism of this condition, it was postulated that repeated raising or forward pushing of the arm applying excessive traction to the origin of the

  19. Evaluation of the influence of dominance rules for the assembly line design problem under consideration of product design alternatives

    Science.gov (United States)

    Oesterle, Jonathan; Lionel, Amodeo

    2018-06-01

    The current competitive situation increases the importance of realistically estimating product costs during the early phases of product and assembly line planning projects. In this article, several multi-objective algorithms using difference dominance rules are proposed to solve the problem associated with the selection of the most effective combination of product and assembly lines. The list of developed algorithms includes variants of ant colony algorithms, evolutionary algorithms and imperialist competitive algorithms. The performance of each algorithm and dominance rule is analysed by five multi-objective quality indicators and fifty problem instances. The algorithms and dominance rules are ranked using a non-parametric statistical test.

  20. Modeling and simulation of bus assem-bling process using DES/ABS approach

    Directory of Open Access Journals (Sweden)

    Pawel PAWLEWSKI

    2017-03-01

    Full Text Available This paper presents the results of the project, which goal is to analyze the production process capability after reengineering the assembly process due to expansion of a bus production plant. The verification of the designed work organization for the new configuration of workstations on new production hall is necessary. To solve these  problems authors propose a method based on mixing DES (Discrete Event Simulation and ABS (Agent Based Simulation approach. DES is using to model the main process – material flow (buses, ABS is using to model assembling operations of teams of  workers.One of obtained goal is to build a simulation model, which presents the new assembly line in the factory, taking into ac-count the arrangement of workstations and work teams in the new production hall as well as the transport between workstations. Second goal is to present work organization of work teams and division of individual workers’ labor (who belongs to a particular work team and performs operations on buses in a particular workstation in order to determine the best allocation of tasks and the optimum size of individual work teams. Proposed solution enables to determine the effect of assembly interferences on the work of particular work teams and the efficiency of the whole production system, to define the efficiency of the designed assembly lines and proposing changes aimed at the quality improvement of the created conception. 

  1. Human Factors and Their Effects on Human-Centred Assembly Systems - A Literature Review-Based Study

    Science.gov (United States)

    Wang, Q.; Abubakar, M. I.

    2017-09-01

    If a product has more than one component, then it must be assembled. Assembly of products relies on assembly systems or lines in which assembly of each product is often carried out manually by human workers following assembly sequences in various forms. It is widely understood that efficiency of assembling a product by reducing assembly times (therefore costs) is vital particularly for small and medium-sized manufacturing companies to survive in an increasingly competitive market. Ideally, it is helpful for pre-determining efficiency or productivity of a human-centred assembly system at the early design stage. To date, most research on performance of an assembly system using modelling simulation methods is focused on its “operational functions”. The term used in a narrow sense always indicates the performance of the “operational system”, which does not incorporate the effect of human factors that may also affect the system performance. This paper presents a research outcome of findings through a literature review-based study by identifying possible human factors that mostly affect the performance on human-centred manufacturing systems as part of the research project incorporating parameters of human factors into a DES (discrete event simulation) tool.

  2. Mathematical model and metaheuristics for simultaneous balancing and sequencing of a robotic mixed-model assembly line

    Science.gov (United States)

    Li, Zixiang; Janardhanan, Mukund Nilakantan; Tang, Qiuhua; Nielsen, Peter

    2018-05-01

    This article presents the first method to simultaneously balance and sequence robotic mixed-model assembly lines (RMALB/S), which involves three sub-problems: task assignment, model sequencing and robot allocation. A new mixed-integer programming model is developed to minimize makespan and, using CPLEX solver, small-size problems are solved for optimality. Two metaheuristics, the restarted simulated annealing algorithm and co-evolutionary algorithm, are developed and improved to address this NP-hard problem. The restarted simulated annealing method replaces the current temperature with a new temperature to restart the search process. The co-evolutionary method uses a restart mechanism to generate a new population by modifying several vectors simultaneously. The proposed algorithms are tested on a set of benchmark problems and compared with five other high-performing metaheuristics. The proposed algorithms outperform their original editions and the benchmarked methods. The proposed algorithms are able to solve the balancing and sequencing problem of a robotic mixed-model assembly line effectively and efficiently.

  3. A Solution Approach to Assembly Line Balancing Problem With Task Related Constraints and an Application At An Enterprise

    Directory of Open Access Journals (Sweden)

    Serkan Altuntaş

    2010-01-01

    Full Text Available Occasionally certain tasks in an assembly line balancing problem are required to be kept together due to some specific reasons. These tasks are attained to the same work stations. Such problems are called as 'Assembly Line Balancing Problem with Task Related Constraints (ALBTRC'. Certain situations like awkward product construction, simultaneous operations or specific requirements leading to zoning and positional constraints like utilization of common resources as tools, jigs and fixtures are implemented thanks to these supplementary constraints. Additionally, materials handling and tooling costs, distances, set-up and lead times are also reduced. Literature on ALBTRC seems quite rare compared to Classical Line Balancing papers, although ALBTRC is one of the common real life balancing problems. This study aimed to develop and implement a novel line balancing method for a manufacturing concern where known methods are impractical to employ due to some specific positional constraints. 'Largest Candidate Method' known as a simple but effective tool is modified for this purpose first. Then a thorough 'method and time study' is conducted to get the necessary data to utilize that method. As a result, more efficient alternatives are generated and presented to decision maker.

  4. Migrant workers and labor market segmentation in Japan.

    Science.gov (United States)

    Mori, H

    1994-01-01

    The amended Immigration Control Act of 1990 focused on 1) redefinition of the resident status of foreign nationals, 2) clarification of immigration regulations, and 3) countermeasures to cope with the problem of illegal migrant workers. Tough penalties were introduced for illegal employment. The reform paved the way for third generation Nikkei (foreigners of Japanese ancestry) and also opened the door to non-Nikkei married to second generation Nikkei to reside in the country. The migration of Nikkei workers to Japan dates back to the beginning of the 1980s. The Technical Intern Training Program introduced in 1993 also opened a legal channel for the employment of unskilled or semi-skilled foreigners. The categories of foreign workers were heavily concentrated in the automobile and electric appliances industries, mostly as assembly line workers. Foreign students and clandestine workers had a wider dispersion in the labor force than the Nikkei. Students often find work in the urban service sector while attending school. Clandestine male workers predominate in the construction industry as unskilled workers. According to the size of firms, small firms had had the most acute labor shortages in the past 15 years prior to 1994, especially in the late 1980s. The Immigration Law of 1990 brought major changes in the hiring practices of large firms that began hiring legal workers such as the Nikkei, while small firms continued hiring clandestine workers from Asian countries. Foreign workers also earned almost as much as native part-time workers and sometimes even outstripped native seasonal workers. In terms of wages, Nikkei South Americans were on the top followed by Pakistanis, Bangladeshis, Sri Lankans, Nepalese, Ghanians, and Iranians on the bottom. Unskilled foreign workers generally had a high turnover rate with the Nikkei showing the lowest rate. Only 7% of the Nikkei changed jobs more than four times vs. 16-17% of foreign students and 21% of clandestine workers.

  5. The Current Working Conditions in Ugandan Apparel Assembly Plants

    Directory of Open Access Journals (Sweden)

    Mike Tebyetekerwa

    2017-12-01

    Full Text Available Background: The present rapid shift of industrialization from developed to developing countries requires developing countries to understand issues related to work organization, management, and working conditions. There are many factors slackening production, of which working conditions is part. A complete inquiry into the workers' working conditions can enable managements to reduce risks in the workplaces and improve productivity. Understanding and awareness of the benefits of workplace research and a probe into the working conditions in the Ugandan apparel assembly plants are urgently required. Methods: A total of 103 (70 women and 33 men workers from five different plants were interviewed. Together with the top management of various plants, questionnaires about the workers' opinions of their physical working conditions were prepared. Data was collected using two methods: (1 questionnaire; and (2 observation of the workers during their work. Results: The results indicated that poor plant working conditions were mainly contributed by the workers' social factors and the management policies. Conclusion: The government, together with the management, should work to improve the working conditions in the apparel assembly plants, as it greatly affects both. Keywords: apparel assembly plants, ergonomics, musculoskeletal disorders, Uganda, working conditions

  6. How front-line healthcare workers respond to stock-outs of essential medicines in the Eastern Cape Province of South Africa.

    Science.gov (United States)

    Hodes, R; Price, I; Bungane, N; Toska, E; Cluver, L

    2017-08-25

    Shortages of essential medicines are a daily occurrence in many of South Africa (SA)'s public health facilities. This study focuses on the responses of healthcare workers to stock-outs, investigating how actors at the 'front line' of public health delivery understand, experience and respond to shortages of essential medicines and equipment in their facilities. Findings are based on focus groups, observations and interviews with healthcare workers and patients at healthcare facilities in the Eastern Cape Province of SA, conducted as part of the Mzantsi Wakho study. The research revealed a discrepancy between 'informal' definitions of stock-outs and their reporting through formal stock-out management channels. Front-line healthcare workers had designed their own systems for classifying the severity of stock-outs, based on the product in question, and on their potential to access stocks from other facilities. Beyond formal systems of procurement and supply, healthcare workers had established vast networks of alternative communication and action, often using personal resources to procure medical supplies. Stock-outs were only reported when informal methods of stock-sharing did not secure top-up supplies. These findings have implications for understanding the frequency and severity of stock-outs, and for taking action to prevent and manage stock-outs effectively.

  7. Assembling Webs of Support: Child Domestic Workers in India

    Science.gov (United States)

    Wasiuzzaman, Shaziah; Wells, Karen

    2010-01-01

    This paper uses ethnographic and qualitative interview data with Muslim child domestic workers, their families and employers to investigate the social ties between young workers and their employers. Our analysis shows that working-class families use children's domestic work with middle-class families as part of a web of resources to protect them…

  8. Workers exposure to electric fields in 400 kV substations and overhead line works

    International Nuclear Information System (INIS)

    Elovaara, J.; Kuisti, H.; Korpinen, L.

    2010-01-01

    The maximum exposing electric field strength magnitude in the highly inhomogeneous 400 kV electric field under work conditions can reach the value of several tens of kV/m. In spite of this the average current density is, in Finland, always lower than 10 mA/m 2 . Furthermore, the total body currents or contact currents are in 400 kV works clearly less than the limit value proposed by the EU's draft for Directive. On the basis of the obtained results it can be concluded that from the limit value point of view it is not necessary to take further actions to reduce the exposure of the workers when they are working in 400 kV substations and on 400 kV overhead lines. However, because the transient peak values of the contact current can be painful and disturb work, it is advisable to develop a safe and reliable method to connect the worker and the work object in the common ground (equipotential bonding). (authors)

  9. Scenario for concurrent conceptual assembly line design: A case study

    Science.gov (United States)

    Mas, F.; Ríos, J.; Menéndez, J. L.

    2012-04-01

    The decision to design and build a new aircraft is preceded by years of research and study. Different disciplines work together throughout the lifecycle to ensure not only a complete functional definition of the product, but also a complete industrialization, a marketing plan, a maintenance plan, etc. This case study focuses on the conceptual design phase. During this phase, the design solutions that will meet the functional and industrial requirements are defined, i.e.: the basic requirements of industrialization. During this phase, several alternatives are studied, and the most attractive in terms of performance and cost requirements is selected. As a result of the study of these alternatives, it is possible to define an early conceptual design of the assembly line and its basic parameters. The plant needs, long cycle jigs & tools or industrial means and human resources with the necessary skills can be determined in advance.

  10. Comparison of subjective symptoms and cold prevention measures in winter between traffic control workers and construction workers in Japan.

    Science.gov (United States)

    Inaba, Ryoichi; Kurokawa, Junichi; Mirbod, Seyed Mohammad

    2009-07-01

    To help making comfortable workplaces and to prevent health disorders induced by the exposure to moderate cold in two different groups of out-door workers, we conducted a survey to compare subjective symptoms and cold prevention measures in winter between traffic control workers and construction workers. The subjects of this study were 98 male traffic control workers and 149 male workers engaged in building construction. Work loads of traffic control workers and construction workers were estimated at RMR1-2 and RMR2-4, respectively. All subjects were asked to complete a self-administered questionnaire covering age, occupational career, working figure, present illness, past history of diseases, individual preventive measures to the cold, subjective symptoms in the winter (43 items) and subjective symptoms occurred during daytime working in the winter (6 items). In two parts of the construction workplaces (the place where a morning assembly was held and on the 7th floor of the construction site) dry bulb, wet bulb and globe temperatures were measured in January. Windchill Index (kcal/cm,(2) x h) was calculated by the measured dry bulb temperature and wind velocity. Mean values of dry bulb temperature between 9:00 and 16:30 in the place where a morning assembly was held for three days were between 4.8 +/- 1.2 degrees C at 9:00 am and 9.3 +/- 1.1 degrees C at noon. Mean values of Windchill Index in the place where a morning assembly was held were between 490.8+/-23.9 kcal/cm(2) x h at 9:30 am and 608.2+/-47.3 kcal/cm(2) x h at 2:30 pm. Occupational career, monthly working days, daily working hours, one way commuting hours, and daily smoking numbers of the traffic control workers were significantly shorter than the construction workers (pconstruction workers (0.7%). Prevalence of wearing a warm underwear, body warmer, warm trousers, underpants, warm socks, shoe warmer and muffler in the traffic control workers were significantly higher than the construction workers. The

  11. 75 FR 54388 - General Motors Company Formerly Known as General Motors Corporation, Orion Assembly Plant...

    Science.gov (United States)

    2010-09-07

    ... Formerly Known as General Motors Corporation, Orion Assembly Plant Including On-Site Leased Workers From Aerotek Automotive Lake Orion, MI; Amended Certification Regarding Eligibility To Apply for Worker... Motors Corporation, Orion Assembly Plant, Lake Orion, Michigan. The notice was published in the Federal...

  12. Relation between sick leave and selected exposure variables among women semiconductor workers in Malaysia

    Science.gov (United States)

    Chee, H; Rampal, K

    2003-01-01

    Aims: To determine the relation between sick leave and selected exposure variables among women semiconductor workers. Methods: This was a cross sectional survey of production workers from 18 semiconductor factories. Those selected had to be women, direct production operators up to the level of line leader, and Malaysian citizens. Sick leave and exposure to physical and chemical hazards were determined by self reporting. Three sick leave variables were used; number of sick leave days taken in the past year was the variable of interest in logistic regression models where the effects of age, marital status, work task, work schedule, work section, and duration of work in factory and work section were also explored. Results: Marital status was strongly linked to the taking of sick leave. Age, work schedule, and duration of work in the factory were significant confounders only in certain cases. After adjusting for these confounders, chemical and physical exposures, with the exception of poor ventilation and smelling chemicals, showed no significant relation to the taking of sick leave within the past year. Work section was a good predictor for taking sick leave, as wafer polishing workers faced higher odds of taking sick leave for each of the three cut off points of seven days, three days, and not at all, while parts assembly workers also faced significantly higher odds of taking sick leave. Conclusion: In Malaysia, the wafer fabrication factories only carry out a limited portion of the work processes, in particular, wafer polishing and the processes immediately prior to and following it. This study, in showing higher illness rates for workers in wafer polishing compared to semiconductor assembly, has implications for the governmental policy of encouraging the setting up of wafer fabrication plants with the full range of work processes. PMID:12660374

  13. Workers on the Line: Activity Guide.

    Science.gov (United States)

    Massachusetts Univ., Lowell. Tsongas Industrial History Center.

    This field trip program, a 90-minute interpretive tour and a 90-minute hands-on workshop, provides students with the opportunity to explore the causes and nature of the conflict between workers and owners which grew out of the Industrial Revolution. The workshop complements the tour by bringing the significance of historic resources to life as…

  14. PENINGKATAN JAMINAN KUALITAS ASSEMBLY LINE (Studi Kasus di Industri Otomotif

    Directory of Open Access Journals (Sweden)

    Halim Junaidi

    2005-01-01

    Full Text Available The paper presents the improvement of quality assurance at an automotive industry which produces multi-purpose vehicle. Their multi-purpose vehicle is a global product, which means that it should concern not only domestic market demand but also international market demand and specification. Thus to maintain customer satisfaction on product quality, one of the efforts can be done to improve quality assurance level is by implementing Quality Assurance Network activity. Abstract in Bahasa Indonesia : Artikel ini membahas peningkatan jaminan kualitas assembly line di industri otomotif yang memproduksi kendaraan niaga. Kendaraan ini adalah produk yang bertaraf global, artinya kendaraan niaga yang harus mampu memenuhi bukan hanya permintaan pasar domestik melainkan juga spesifikasi dan permintaan pasar mancanegara. Oleh sebab itu untuk tetap dapat mempertahankan kepuasan konsumen terhadap kualitas produk, salah satu upaya yang dapat digunakan meningkatkan jaminan kualitas perusahaan adalah dengan mengimplementasikan aktivitas quality assurance network. Kata kunci: jaminan kualitas, aktivitas quality assurance network.

  15. The Current Working Conditions in Ugandan Apparel Assembly Plants.

    Science.gov (United States)

    Tebyetekerwa, Mike; Akankwasa, Nicholus Tayari; Marriam, Ifra

    2017-12-01

    The present rapid shift of industrialization from developed to developing countries requires developing countries to understand issues related to work organization, management, and working conditions. There are many factors slackening production, of which working conditions is part. A complete inquiry into the workers' working conditions can enable managements to reduce risks in the workplaces and improve productivity. Understanding and awareness of the benefits of workplace research and a probe into the working conditions in the Ugandan apparel assembly plants are urgently required. A total of 103 (70 women and 33 men) workers from five different plants were interviewed. Together with the top management of various plants, questionnaires about the workers' opinions of their physical working conditions were prepared. Data was collected using two methods: (1) questionnaire; and (2) observation of the workers during their work. The results indicated that poor plant working conditions were mainly contributed by the workers' social factors and the management policies. The government, together with the management, should work to improve the working conditions in the apparel assembly plants, as it greatly affects both.

  16. The First Assembly Line of Large-longitudinally-welded Steel Pipe in China Went into Operation

    Institute of Scientific and Technical Information of China (English)

    Li Bing

    2002-01-01

    @@ On July 27, the first assembly line to produce JCOE large diameter Longitudinally-submerged-arc-welded steel pipe in China, Which is the key homemade equipment project of "West-East Gas Transmission"project, was put into production. Chen Gen, vice general manager of CNPC; Xie Zhiqiang and Liu Haisheng, assistant chief manager of CNPC; Shi Xingquan, vice president of PetroChina; and the president of Itochu-Marubeni Steel & iron Co., Ltd.of Japan; attended the opening ceremony and cut the ribbon.

  17. Model-Based Control of a Continuous Coating Line for Proton Exchange Membrane Fuel Cell Electrode Assembly

    Directory of Open Access Journals (Sweden)

    Vikram Devaraj

    2015-01-01

    Full Text Available The most expensive component of a fuel cell is the membrane electrode assembly (MEA, which consists of an ionomer membrane coated with catalyst material. Best-performing MEAs are currently fabricated by depositing and drying liquid catalyst ink on the membrane; however, this process is limited to individual preparation by hand due to the membrane’s rapid water absorption that leads to shape deformation and coating defects. A continuous coating line can reduce the cost and time needed to fabricate the MEA, incentivizing the commercialization and widespread adoption of fuel cells. A pilot-scale membrane coating line was designed for such a task and is described in this paper. Accurate process control is necessary to prevent manufacturing defects from occurring in the coating line. A linear-quadratic-Gaussian (LQG controller was developed based on a physics-based model of the coating process to optimally control the temperature and humidity of the drying zones. The process controller was implemented in the pilot-scale coating line proving effective in preventing defects.

  18. Simulation based assembly and alignment process ability analysis for line replaceable units of the high power solid state laser facility

    International Nuclear Information System (INIS)

    Wang, Junfeng; Lu, Cong; Li, Shiqi

    2016-01-01

    Highlights: • Discrete event simulation is applied to analyze the assembly and alignment process ability of LRUs in SG-III facility. • The overall assembly and alignment process of LRUs with specific characteristics is described. • An extended-directed graph is proposed to express the assembly and alignment process of LRUs. • Different scenarios have been simulated to evaluate assembling process ability of LRUs and decision making is supported to ensure the construction millstone. - Abstract: Line replaceable units (LRUs) are important components of the very large high power solid state laser facilities. The assembly and alignment process ability of LRUs will impact the construction milestone of facilities. This paper describes the use of discrete event simulation method for assembly and alignment process analysis of LRUs in such facilities. The overall assembly and alignment process for LRUs is presented based on the layout of the optics assembly laboratory and the process characteristics are analyzed. An extended-directed graph is proposed to express the assembly and alignment process of LRUs. Taking the LRUs of disk amplifier system in Shen Guang-III (SG-III) facility as the example, some process simulation models are built based on the Quest simulation platform. The constraints, such as duration, equipment, technician and part supply, are considered in the simulation models. Different simulation scenarios have been carried out to evaluate the assembling process ability of LRUs. The simulation method can provide a valuable decision making and process optimization tool for the optics assembly laboratory layout and the process working out of such facilities.

  19. Simulation based assembly and alignment process ability analysis for line replaceable units of the high power solid state laser facility

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Junfeng; Lu, Cong; Li, Shiqi, E-mail: sqli@hust.edu.cn

    2016-11-15

    Highlights: • Discrete event simulation is applied to analyze the assembly and alignment process ability of LRUs in SG-III facility. • The overall assembly and alignment process of LRUs with specific characteristics is described. • An extended-directed graph is proposed to express the assembly and alignment process of LRUs. • Different scenarios have been simulated to evaluate assembling process ability of LRUs and decision making is supported to ensure the construction millstone. - Abstract: Line replaceable units (LRUs) are important components of the very large high power solid state laser facilities. The assembly and alignment process ability of LRUs will impact the construction milestone of facilities. This paper describes the use of discrete event simulation method for assembly and alignment process analysis of LRUs in such facilities. The overall assembly and alignment process for LRUs is presented based on the layout of the optics assembly laboratory and the process characteristics are analyzed. An extended-directed graph is proposed to express the assembly and alignment process of LRUs. Taking the LRUs of disk amplifier system in Shen Guang-III (SG-III) facility as the example, some process simulation models are built based on the Quest simulation platform. The constraints, such as duration, equipment, technician and part supply, are considered in the simulation models. Different simulation scenarios have been carried out to evaluate the assembling process ability of LRUs. The simulation method can provide a valuable decision making and process optimization tool for the optics assembly laboratory layout and the process working out of such facilities.

  20. The Impact of the Availability of Resources, the Allocation of Buffers and Number of Workers on the Effectiveness of an Assembly Manufacturing System

    OpenAIRE

    Kłos Sławomir; Trebuna Peter

    2017-01-01

    This paper proposes the application of computer simulation methods in order to analyse the availability of resources, buffers and the impact of the allocation of workers on the throughput and work-in-progress of a manufacturing system. The simulation model of the production system is based on an existing example of a manufacturing company in the automotive industry. The manufacturing system includes both machining and assembly operations. Simulation experiments were conducted vis-à-vis the av...

  1. USER-CENTERED DESIGN SEBAGAI METODE PENINGKATAN KONTROL KOGNITIF PADA LINI ASSEMBLY (STUDI KASUS PT. KUBOTA INDONESIA

    Directory of Open Access Journals (Sweden)

    Novie Susanto

    2012-02-01

    Full Text Available In developing countries like Indonesia, the rationalization of production processes and systems will increase.Challenge that emerged significantly is the increase in planning efficiency. A prospective approach to reduce theplanning effort is the development of a production system capable of optimizing itself during the process. On theassembly line PT. Kubota Indonesia found that the workers perform assembly process with a sequence that is notplanned as a result of the lack of a standardized sequence of process companies and lead to cognitive controlthat are not stable and continuous learning process. Because this issue contrary to the concept of efficiency inplanning, it takes an automated system with a complete and fully optimized (self-optimizing production system.The purpose of this study is to apply the planning efficiency through implementation of optimized productionsystem (self-optimizing production systems in assembly-line PT. Kubota Indonesia. Data obtaining done by thedetermination of primary and secondary variables include the perception of cognitive control, a solution basedon the memory (memory, and action. Repairs are carried out is by applying self-optimizing production systemconsisting of 4 steps: the development of cognitive architecture is to determine the sequence of work andapplying it to extend the software, implementation of individual modules is through the use of hand screw, thedevelopment of human machine interfaces in hand tool screw is through the explanation task analysis andimplementation and evaluation of improvement is the use of robotic assembly in the assembly processenvironment.

  2. First robotized assembly line in for multivalve cylinder heads in Europe; Erste roborterautomatisierte Montagelinie fuer Mehrventilzylinderkoepfe in Europa

    Energy Technology Data Exchange (ETDEWEB)

    Simonis, G. [ABB Flexible Automation GmbH, Langenfeld (Germany)

    1996-12-31

    From its earliest days the automotive industry has pioneered the automation of factory operations. This reputation is being added to by yet another new development in the assembly area. The trendsetter is ABB Flexible Automation GmbH, based in Butzbach, Germany, which has developed a future-oriented concept for vehicle engine assembly in which jointed-arm robots play a key role. The new concept has been adopted for Europe`s first robotized assembly line for multivalve cylinder heads, installed by ABB for the German carmaker Audi in Gyoer, Hungary. (orig.) [Deutsch] Die Automobilindustrie war und ist Vorreiter in der Automatisierung betrieblicher Ablaeufe. Einmal mehr zeigt sich dies im Montagebereich. Trendsetter ist hier die ABB Flexible Automation GmbH, Butzbach/Deutschland, die fuer die Montage von Fahrzeugaggregaten ein zukunftweisendes Konzept entwickelt hat. Gelenkarmroboter spielen dabei eine entscheidende Rolle. Ein Beispiel dafuer: Die erste roboterautomatisierte Montageanlage fuer Mehrventilzylinderkoepfe in Europa, die ABB fuer den Automobilhersteller Audi im ungarischen Gyoer realisiert hat. (orig.)

  3. Fuel assembly reconstitution

    International Nuclear Information System (INIS)

    Morgado, Mario M.; Oliveira, Monica G.N.; Ferreira Junior, Decio B.M.; Santos, Barbara O. dos; Santos, Jorge E. dos

    2009-01-01

    Fuel failures have been happened in Nuclear Power Plants worldwide, without lost of integrity and safety, mainly for the public, environment and power plants workers. The most common causes of these events are corrosion (CRUD), fretting and pellet cladding interaction. These failures are identified by increasing the activity of fission products, verified by chemical analyses of reactor coolant. Through these analyses, during the fourth operation cycle of Angra 2 Nuclear Power Plant, was possible to observe fuel failure indication. This indication was confirmed in the end of the cycle during the unloading of reactor core through leakage tests of fuel assembly, using the equipment called 'In Mast Sipping' and 'Box Sipping'. After confirmed, the fuel assembly reconstitution was scheduled, and happened in April, 2007, where was identified the cause and the fuel rod failure, which was substitute by dummy rods (zircaloy). The cause was fretting by 'debris'. The actions to avoid and prevent fuel assemblies failures are important. The goals of this work are to describe the methodology of fuel assembly reconstitution using the FARE (Fuel Assembly Reconstitution Equipment) system, to describe the results of this task in economic and security factors of the company and show how the fuel assembly failures are identified during operation and during the outage. (author)

  4. Factors affecting job satisfaction of front-line extension workers in ...

    African Journals Online (AJOL)

    The study examined the factors affecting job satisfaction of field extension workers in Enugu State Agricultural Development Programme. Forty-two extension staff randomly selected across the three agricultural zones were used for the study. The field extension workers indicated low level of satisfaction with their job content, ...

  5. An effective model for ergonomic optimization applied to a new automotive assembly line

    Energy Technology Data Exchange (ETDEWEB)

    Duraccio, Vincenzo [University Niccolò Cusano, Rome Via Don Gnocchi,00166, Roma Italy (Italy); Elia, Valerio [Dept. of Innovation Engineering - University of Salento Via Monteroni, 73100, Lecce (Italy); Forcina, Antonio [University Parthenope, Dep. of Engineering Centro Direzionale - Isola C4 80143 - Naples - Italy (Italy)

    2016-06-08

    An efficient ergonomic optimization can lead to a significant improvement in production performance and a considerable reduction of costs. In the present paper new model for ergonomic optimization is proposed. The new approach is based on the criteria defined by National Institute of Occupational Safety and Health and, adapted to Italian legislation. The proposed model provides an ergonomic optimization, by analyzing ergonomic relations between manual work in correct conditions. The model includes a schematic and systematic analysis method of the operations, and identifies all possible ergonomic aspects to be evaluated. The proposed approach has been applied to an automotive assembly line, where the operation repeatability makes the optimization fundamental. The proposed application clearly demonstrates the effectiveness of the new approach.

  6. An effective model for ergonomic optimization applied to a new automotive assembly line

    International Nuclear Information System (INIS)

    Duraccio, Vincenzo; Elia, Valerio; Forcina, Antonio

    2016-01-01

    An efficient ergonomic optimization can lead to a significant improvement in production performance and a considerable reduction of costs. In the present paper new model for ergonomic optimization is proposed. The new approach is based on the criteria defined by National Institute of Occupational Safety and Health and, adapted to Italian legislation. The proposed model provides an ergonomic optimization, by analyzing ergonomic relations between manual work in correct conditions. The model includes a schematic and systematic analysis method of the operations, and identifies all possible ergonomic aspects to be evaluated. The proposed approach has been applied to an automotive assembly line, where the operation repeatability makes the optimization fundamental. The proposed application clearly demonstrates the effectiveness of the new approach.

  7. An effective model for ergonomic optimization applied to a new automotive assembly line

    Science.gov (United States)

    Duraccio, Vincenzo; Elia, Valerio; Forcina, Antonio

    2016-06-01

    An efficient ergonomic optimization can lead to a significant improvement in production performance and a considerable reduction of costs. In the present paper new model for ergonomic optimization is proposed. The new approach is based on the criteria defined by National Institute of Occupational Safety and Health and, adapted to Italian legislation. The proposed model provides an ergonomic optimization, by analyzing ergonomic relations between manual work in correct conditions. The model includes a schematic and systematic analysis method of the operations, and identifies all possible ergonomic aspects to be evaluated. The proposed approach has been applied to an automotive assembly line, where the operation repeatability makes the optimization fundamental. The proposed application clearly demonstrates the effectiveness of the new approach.

  8. Efficient flow and human centred assembly by an interactive approach

    NARCIS (Netherlands)

    Eikhout, S.M.; Helmes, R.B.M.; Rhijn, J.W. van

    2004-01-01

    Due to fluctuations on the market, manufacturing of many product variations, and wish for fine-tuning between production and assembly a fan and motor manufacturing company wanted to improve their assembly line. The aims were efficient flow and human centered assembly in the new product line.

  9. Hand Gesture Modeling and Recognition for Human and Robot Interactive Assembly Using Hidden Markov Models

    Directory of Open Access Journals (Sweden)

    Fei Chen

    2015-04-01

    Full Text Available Gesture recognition is essential for human and robot collaboration. Within an industrial hybrid assembly cell, the performance of such a system significantly affects the safety of human workers. This work presents an approach to recognizing hand gestures accurately during an assembly task while in collaboration with a robot co-worker. We have designed and developed a sensor system for measuring natural human-robot interactions. The position and rotation information of a human worker's hands and fingertips are tracked in 3D space while completing a task. A modified chain-code method is proposed to describe the motion trajectory of the measured hands and fingertips. The Hidden Markov Model (HMM method is adopted to recognize patterns via data streams and identify workers' gesture patterns and assembly intentions. The effectiveness of the proposed system is verified by experimental results. The outcome demonstrates that the proposed system is able to automatically segment the data streams and recognize the gesture patterns thus represented with a reasonable accuracy ratio.

  10. Advance on the technology of assembly and disassembly of a head frame with four legs and the machine-assembled head frame

    Energy Technology Data Exchange (ETDEWEB)

    Zhou Youzong; Cao Baozhen [Ministry of Coal Industry (China). Geological Exploration Machinery Factory

    1996-12-31

    According to the meditation of assembling headframes from upper to lower instead of that from lower to upper, the authors created successfully a new type of machine for assembling and disassembling headframes as well as a type of machine-assembled headframe. The new type of headframe not only has the merits of old type of headframe with four legs, but also can keep people away from dangers of working in high space and save the workers much labour. The new technology has good effect on raising productive efficiency. 2 figs.

  11. Cellular Genetic Algorithm with Communicating Grids for Assembly Line Balancing Problems

    Directory of Open Access Journals (Sweden)

    BRUDARU, O.

    2010-05-01

    Full Text Available This paper presents a new approach with cellular multigrid genetic algorithms for the "I"-shaped and "U"-shaped assembly line balancing problems, including parallel workstations and compatibility constraints. First, a cellular hybrid genetic algorithm that uses a single grid is described. Appropriate operators for mutation, hypermutation, and crossover and two devoration techniques are proposed for creating and maintaining groups based on similarity. This monogrid algorithm is extended for handling many populations placed on different grids. In the multigrid version, the population of each grid is organized in clusters using the positional information of the chromosomes. A similarity preserving communication protocol between the clusters placed on different grids is introduced. The experimental evaluation shows that the multigrid cellular genetic algorithm with communicating grids is better than the hybrid genetic algorithm used for building it, whereas it dominates the monogrid version in all cases. Absolute performance is evaluated using classical benchmarks. The role of certain components of the cellular algorithm is explained and the effect of some parameters is evaluated.

  12. Transportation of part supply improvement in agricultural machinery assembly plant

    Science.gov (United States)

    Saysaman, Anusit; Chutima, Parames

    2018-02-01

    This research focused on the problem caused by the transportation of part supply in agricultural machinery assembly plant in Thailand, which is one of the processes that are critical to the whole production process. If poorly managed, it will affect transportation of part supply, the emergence of sink cost, quality problems, and the ability to respond to the needs of the customers in time. Since the competition in the agricultural machinery market is more intense, the efficiency of part transportation process has to be improved. In this study, the process of transporting parts of the plant was studied and it was found that the efficiency of the process of transporting parts from the sub assembly line to its main assembly line was 83%. The approach to the performance improvement is done by using the Lean tool to limit wastes based on the ECRS principle and applying pull production system by changing the transportation method to operate as milkrun for transportation of parts to synchronize with the part demands of the main assembly line. After the transportation of parts from sub-assembly line to the main assembly line was improved, the efficiency raised to 98% and transportation process cost was saved to 540,000 Baht per year.

  13. Motor adaptation capacity as a function of age in carrying out a repetitive assembly task at imposed work paces.

    Science.gov (United States)

    Gilles, Martine Annie; Guélin, Jean-Charles; Desbrosses, Kévin; Wild, Pascal

    2017-10-01

    The working population is getting older. Workers must adapt to changing conditions to respond to the efforts required by the tasks they have to perform. In this laboratory-based study, we investigated the capacities of motor adaptation as a function of age and work pace. Two phases were identified in the task performed: a collection phase, involving dominant use of the lower limbs; and an assembly phase, involving bi-manual motor skills. Results showed that senior workers were mainly limited during the collection phase, whereas they had less difficulty completing the assembly phase. However, senior workers did increase the vertical force applied while assembling parts, whatever the work pace. In younger and middle-aged subjects, vertical force was increased only for the faster pace. Older workers could adapt to perform repetitive tasks under different time constraints, but adaptation required greater effort than for younger workers. These results point towards a higher risk of developing musculoskeletal disorders among seniors. Copyright © 2017 Elsevier Ltd. All rights reserved.

  14. On the line: worker democracy and the struggle over occupational health and safety.

    Science.gov (United States)

    Granzow, Kara; Theberge, Nancy

    2009-01-01

    In this article we present a qualitative analysis of worker involvement in a participatory project to improve occupational health and safety at a Canadian manufacturing site. Based on interviews with workers in the plant, we consider the manner and degree to which workers experienced meaningful participation in the intervention process and some of the main barriers to worker participation. Findings emphasize the importance of the social and political context in conditioning the dynamics of joint management labor ventures specifically in relation to health initiatives. Interviews revealed few instances in which workers felt included in the participatory initiative; most often they felt marginalized. In the absence of structural change in the plant, workers described the health initiative as seriously limited in its ability to render meaningful worker participation. These results extend beyond this analysis of a participatory workplace health initiative, offering insights into the dynamics of institutional participatory process, and into participatory research practice generally.

  15. Preferred 11 different job rotation types in automotive company and their effects on productivity, quality and musculoskeletal disorders: comparison between subjective and actual scores by workers' age.

    Science.gov (United States)

    Jeon, In Sik; Jeong, Byung Yong; Jeong, Ji Hyun

    2016-10-01

    This study investigates workers' favoured rotation types by their age and compares means between subjective and actual scores on productivity, quality and musculoskeletal disorders (MSDs). The subjects of research were 422 assembly line units in Hyundai Motor Company. The survey of 422 units focused on the workers' preference for 11 different rotation types and subjective scores for each type's perceived benefits, both by the workers' age. Then, actual scores on production-related indices were traced over a five-year period. The results suggest that different rotation types lead to different results in productivity, product quality and MSDs. Workers tend to perceive job rotation as a helpful method to enhance satisfaction, productivity and product quality more so than the actual production data suggests. Job rotation was especially effective in preventing MSDs for workers aged under 45, while its effects were not clear for the workers aged 45 years or older. Practitioner's Summary: This research presents appropriate rotation type for different age groups. Taking workers' age into account, administrators can use the paper's outcomes to select and implement the suitable rotation type to attain specific goals such as enhancing productivity, improving product quality or reducing MSDs.

  16. Visual Perception-Based Statistical Modeling of Complex Grain Image for Product Quality Monitoring and Supervision on Assembly Production Line.

    Directory of Open Access Journals (Sweden)

    Jinping Liu

    Full Text Available Computer vision as a fast, low-cost, noncontact, and online monitoring technology has been an important tool to inspect product quality, particularly on a large-scale assembly production line. However, the current industrial vision system is far from satisfactory in the intelligent perception of complex grain images, comprising a large number of local homogeneous fragmentations or patches without distinct foreground and background. We attempt to solve this problem based on the statistical modeling of spatial structures of grain images. We present a physical explanation in advance to indicate that the spatial structures of the complex grain images are subject to a representative Weibull distribution according to the theory of sequential fragmentation, which is well known in the continued comminution of ore grinding. To delineate the spatial structure of the grain image, we present a method of multiscale and omnidirectional Gaussian derivative filtering. Then, a product quality classifier based on sparse multikernel-least squares support vector machine is proposed to solve the low-confidence classification problem of imbalanced data distribution. The proposed method is applied on the assembly line of a food-processing enterprise to classify (or identify automatically the production quality of rice. The experiments on the real application case, compared with the commonly used methods, illustrate the validity of our method.

  17. Visual Perception-Based Statistical Modeling of Complex Grain Image for Product Quality Monitoring and Supervision on Assembly Production Line.

    Science.gov (United States)

    Liu, Jinping; Tang, Zhaohui; Zhang, Jin; Chen, Qing; Xu, Pengfei; Liu, Wenzhong

    2016-01-01

    Computer vision as a fast, low-cost, noncontact, and online monitoring technology has been an important tool to inspect product quality, particularly on a large-scale assembly production line. However, the current industrial vision system is far from satisfactory in the intelligent perception of complex grain images, comprising a large number of local homogeneous fragmentations or patches without distinct foreground and background. We attempt to solve this problem based on the statistical modeling of spatial structures of grain images. We present a physical explanation in advance to indicate that the spatial structures of the complex grain images are subject to a representative Weibull distribution according to the theory of sequential fragmentation, which is well known in the continued comminution of ore grinding. To delineate the spatial structure of the grain image, we present a method of multiscale and omnidirectional Gaussian derivative filtering. Then, a product quality classifier based on sparse multikernel-least squares support vector machine is proposed to solve the low-confidence classification problem of imbalanced data distribution. The proposed method is applied on the assembly line of a food-processing enterprise to classify (or identify) automatically the production quality of rice. The experiments on the real application case, compared with the commonly used methods, illustrate the validity of our method.

  18. New Wireless Network for Uganda's Healthcare Workers | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    2010-11-10

    Nov 10, 2010 ... Physicians and health care workers working in locations without fixed-line ... face serious problems in sharing and accessing critical medical and public ... to be a powerful tool for doctors and health care workers in Uganda.

  19. Assembling the LHC short straight sections

    CERN Document Server

    Maximilien Brice

    2005-01-01

    The building where the short straight sections are being assembled, was often called ‘Lego Land’ by the workers because of the wide variety of sets of magnets and cryostats. Short straight sections contain magnets for manipulating the beam inside cryostats with liquid helium to keep the magnets at a cool 1.9 K (-271.3°C).

  20. 75 FR 67770 - General Motors Company, Formerly Known as General Motors Corporation, Orion Assembly Plant...

    Science.gov (United States)

    2010-11-03

    ..., Formerly Known as General Motors Corporation, Orion Assembly Plant, Including On-Site Leased Workers From Aerotek Automotive, Ryder and Premier Manufacturing Support Services, Lake Orion, MI; Amended... of General Motors Company, formerly known as General Motors Corporation, Orion Assembly Plant, Lake...

  1. No effects of power line frequency extremely low frequency electromagnetic field exposure on selected neurobehavior tests of workers inspecting transformers and distribution line stations versus controls.

    Science.gov (United States)

    Li, Li; Xiong, De-fu; Liu, Jia-wen; Li, Zi-xin; Zeng, Guang-cheng; Li, Hua-liang

    2014-03-01

    We aimed to evaluate the interference of 50 Hz extremely low frequency electromagnetic field (ELF-EMF) occupational exposure on the neurobehavior tests of workers performing tour-inspection close to transformers and distribution power lines. Occupational short-term "spot" measurements were carried out. 310 inspection workers and 300 logistics staff were selected as exposure and control. The neurobehavior tests were performed through computer-based neurobehavior evaluation system, including mental arithmetic, curve coincide, simple visual reaction time, visual retention, auditory digit span and pursuit aiming. In 500 kV areas electric field intensity at 71.98% of total measured 590 spots were above 5 kV/m (national occupational standard), while in 220 kV areas electric field intensity at 15.69% of total 701 spots were above 5 kV/m. Magnetic field flux density at all the spots was below 1,000 μT (ICNIRP occupational standard). The neurobehavior score changes showed no statistical significance. Results of neurobehavior tests among different age, seniority groups showed no significant changes. Neurobehavior changes caused by daily repeated ELF-EMF exposure were not observed in the current study.

  2. Caring for home-based care workers | de Saxe Zerden | Southern ...

    African Journals Online (AJOL)

    care workers provide critical services, which include physical, psychosocial, and palliative care activities.1 A quantitative and qualitative study of home-based care workers in South Africa was conducted in 2005 to better understand the needs, fears and motivations of front-line care workers at Thembalethu Home Based ...

  3. ANALYSIS OF THE GAZE BEHAVIOUR OF THE WORKER ON THE CARBURETOR ASSEMBLY TASK

    Directory of Open Access Journals (Sweden)

    Novie Susanto

    2015-06-01

    Full Text Available This study presents analysis of the area of interest (AOI and the gaze behavior of human during assembly task. This study aims at investigating the human behavior in detail using an eye‐tracking system during assembly task using LEGO brick and an actual manufactured product, a carburetor. An analysis using heat map data based on the recorded videos from the eye-tracking system is taken into account to examine and investigate the gaze behavior of human. The results of this study show that the carburetor assembly requires more attention than the product made from LEGO bricks. About 50% of the participants experience the necessity to visually inspect the interim state of the work object during the simulation of the assembly sequence on the screen. They also show the tendency to want to be more certain about part fitting in the actual work object.

  4. Penicillin dust exposure and penicillin resistance among pharmaceutical workers in Tehran, Iran.

    Science.gov (United States)

    Farshad, Ali Asghar; Enferadi, Mojtaba; Bakand, Shahnaz; Jamshidi Orak, Rouhangiz; Mirkazemi, Roksana

    2016-07-01

    Antimicrobial resistance (AMR) adversely impacts the prevention and treatment of a wide range of infections and is considered as a serious threat to global public health. Occupational-related AMR is a neglected area of research. To assess exposure to penicillin dust, penicillin active materials, and to report the frequency of penicillin resistance among pharmaceutical workers in Tehran, Iran. A quasi-experimental study was conducted among workers on a penicillin production line in a pharmaceutical company (n = 60) and workers in a food producing company (n = 60). Data were collected via survey, air sampling, and throat swab. The mean overall concentrations of penicillin dust and penicillin active material were 6.6 and 4.3 mg/m 3 , respectively, in the pharmaceutical industry. Streptococcus pneumoniae (S. pneumoniae) was detected in 45% (27) individuals in the exposed group, 92.6% of which showed penicillin resistance. Resistance was significantly higher among workers in penicillin production line (p = 0.014). High level of AMR among workers in penicillin production line is a health risk for the workers as well as society as a whole through the spread of drug resistant micro-organisms.

  5. FB Line Basis for Interim Operation

    International Nuclear Information System (INIS)

    Shedrow, B.

    1998-01-01

    The safety analysis of the FB-Line Facility indicates that the operation of FB-Line to support the current mission does not present undue risk to the facility and co-located workers, general public, or the environment

  6. Simulation and optimization of logistics distribution for an engine production line

    Energy Technology Data Exchange (ETDEWEB)

    Song, L.; Jin, S.; Tang, P.

    2016-07-01

    In order to analyze and study the factors about Logistics distribution system, solve the problems of out of stock on the production line and improve the efficiency of the assembly line. Using the method of industrial engineering, put forward the optimization scheme of distribution system. The simulation model of logistics distribution system for engine assembly line was build based on Witness software. The optimization plan is efficient to improve Logistics distribution efficiency, production of assembly line efficiency and reduce the storage of production line. Based on the study of the modeling and simulation of engine production logistics distribution system, the result reflects some influence factors about production logistics system, which has reference value to improving the efficiency of the production line. (Author)

  7. ANALISIS IDENTIFIKASI MASALAH DENGAN MENGGUNAKAN METODE FAILURE MODE AND EFFECT ANALYSIS (FMEA DAN RISK PRIORITY NUMBER (RPN PADA SUB ASSEMBLY LINE (Studi Kasus : PT. Toyota Motor Manufacturing Indonesia

    Directory of Open Access Journals (Sweden)

    Nia Budi Puspitasari

    2017-07-01

    Abstract The failure rate is a problem that has always attempted to be minimized by a company in order to improve the quality of products, and also were conducted by oleh Toyota Motor Manufacturing Indonesia (PT. TMMIN which is consistent in producting a quality product.  Knowing that in 2016 there is a defect GAP at 50 ppm, PT. TMMIN needs to identify the failures that occur in their company. FMEA is a method to identify and analyze the failure modes in detail that can able to know the cause and impact of each failures, so we get the proper repairment. FMEA that is used in PT. TMMIN case study indicate various modes of failure in assembly-line, then known the alternatives to repair for any prioritize failures. The priorities failures can be seen in the Risk Priority Number (RPN. Based on the RPN resulting, we can obtain the priority failures in  assembly-line of PT. TMMIN that are about the part installation errors, failures due to foreign objects in the part, and the failure of the piston assembly errors.

  8. Legal content of the International Convention on the Protection of the Rights of All Migrant Workers and Members of Their Families, adopted by the united nations general assembly by resolution 45/158 of 18 December 1990.

    Directory of Open Access Journals (Sweden)

    Aurelia Álvarez Rodríguez

    2016-10-01

    Full Text Available The author makes a detailed analysis of the legal contents of the International Convention on the Protection of the Rights of all Migrant workers and their Families, adopted by the General Assembly of the United Nations in the Resolution 45/158 of December 1990. The objectives of the Convention, the personal spehere of application, the Human Rights of all migrant workers and their families wether they be regular of iregular are presented throughout the article. Finally, the practical effectiveness of the Convention is analyzed concluding with the importance of its ratification by the largest number of States possible.

  9. Ergonomic risk factors of work processes in the semiconductor industry in Peninsular Malaysia.

    Science.gov (United States)

    Chee, Heng-Leng; Rampal, Krishna Gopal; Chandrasakaran, Abherhame

    2004-07-01

    A cross-sectional survey of semiconductor factories was conducted to identify the ergonomic risk factors in the work processes, the prevalence of body pain among workers, and the relationship between body pain and work processes. A total of 906 women semiconductor workers took part in the study. In wafer preparation and polishing, a combination of lifting weights and prolonged standing might have led to high pain prevalences in the low back (35.0% wafer preparation, 41.7% wafer polishing) and lower limbs (90.0% wafer preparation, 66.7% wafer polishing). Semiconductor front of line workers, who mostly walked around to operate machines in clean rooms, had the lowest prevalences of body pain. Semiconductor assembly middle of line workers, especially the molding workers, who did frequent lifting, had high pain prevalences in the neck/shoulders (54.8%) and upper back (43.5 %). In the semiconductor assembly end of line work section, chip inspection workers who were exposed to prolonged sitting without back support had high prevalences of neck/shoulder (62.2%) and upper back pain (50.0%), while chip testing workers who had to climb steps to load units had a high prevalence of lower limb pain (68.0%). Workers in the assembly of electronic components, carrying out repetitive tasks with hands and fingers, and standing in awkward postures had high pain prevalences in the neck/shoulders (61.5%), arms (38.5%), and hands/wrists (30.8%).

  10. Modeling of RFID-Enabled Real-Time Manufacturing Execution System in Mixed-Model Assembly Lines

    Directory of Open Access Journals (Sweden)

    Zhixin Yang

    2015-01-01

    Full Text Available To quickly respond to the diverse product demands, mixed-model assembly lines are well adopted in discrete manufacturing industries. Besides the complexity in material distribution, mixed-model assembly involves a variety of components, different process plans and fast production changes, which greatly increase the difficulty for agile production management. Aiming at breaking through the bottlenecks in existing production management, a novel RFID-enabled manufacturing execution system (MES, which is featured with real-time and wireless information interaction capability, is proposed to identify various manufacturing objects including WIPs, tools, and operators, etc., and to trace their movements throughout the production processes. However, being subject to the constraints in terms of safety stock, machine assignment, setup, and scheduling requirements, the optimization of RFID-enabled MES model for production planning and scheduling issues is a NP-hard problem. A new heuristical generalized Lagrangian decomposition approach has been proposed for model optimization, which decomposes the model into three subproblems: computation of optimal configuration of RFID senor networks, optimization of production planning subjected to machine setup cost and safety stock constraints, and optimization of scheduling for minimized overtime. RFID signal processing methods that could solve unreliable, redundant, and missing tag events are also described in detail. The model validity is discussed through algorithm analysis and verified through numerical simulation. The proposed design scheme has important reference value for the applications of RFID in multiple manufacturing fields, and also lays a vital research foundation to leverage digital and networked manufacturing system towards intelligence.

  11. Analysis of reconfigurable assembly system framing systems in automotive industry

    Directory of Open Access Journals (Sweden)

    Md Zain Mohamad Zamri

    2017-01-01

    Full Text Available Current trend in automotive industry shows increasing demand for multiple models with lean production. Prior to that, automotive manufacturing systems evolved from mass production to flexible automation. Material handling systems and equipment in a single assembly line with multiple models require high investment but with low throughput thus making production cost relatively high. Current assembly process of side structure and undercarriage with downtime occurrence during assembly process affecting production performance (quality, cost and delivery. Manufacturing facilities should allow more flexibility and increase intelligence evolving toward novel reconfigurable assembly systems (RAS. RAS is envisaged capable of increasing factor flexibility and responsiveness by incorporating assembly jig, robot and framing, which could be next generation of world class automotive assembly systems. This project research proposes a new methodology of framework reconfigurable assembly systems principles in automotive framing systems i.e. enhance assembly process between side structure assembly and undercarriage assembly which a new RAS is capable to reconfigure the assembly processes of multiple model on a single assembly line. Simulation software (Witness will be used to simulate and validate current and proposed assembly process. RAS is expected to be a solution for rapid change in structure and for a responsively adjustable production capacity. Quality, cost and delivery are production key parameters that can be achieved by implementing RAS.

  12. Workplace violence against homecare workers and its relationship with workers health outcomes: a cross-sectional study.

    Science.gov (United States)

    Hanson, Ginger C; Perrin, Nancy A; Moss, Helen; Laharnar, Naima; Glass, Nancy

    2015-01-17

    Consumer-driven homecare models support aging and disabled individuals to live independently through the services of homecare workers. Although these models have benefits, including autonomy and control over services, little evidence exists about challenges homecare workers may face when providing services, including workplace violence and the negative outcomes associated with workplace violence. This study investigates the prevalence of workplace violence among homecare workers and examines the relationship between these experiences and homecare worker stress, burnout, depression, and sleep. We recruited female homecare workers in Oregon, the first US state to implement a consumer driven homecare model, to complete an on-line or telephone survey with peer interviewers. The survey asked about demographics and included measures to assess workplace violence, fear, stress, burnout, depression and sleep problems. Homecare workers (n = 1,214) reported past-year incidents of verbal aggression (50.3% of respondents), workplace aggression (26.9%), workplace violence (23.6%), sexual harassment (25.7%), and sexual aggression (12.8%). Exposure was associated with greater stress (p workplace aggression buffered homecare workers against negative work and health outcomes. To ensure homecare worker safety and positive health outcomes in the provision of services, it is critical to develop and implement preventive safety training programs with policies and procedures that support homecare workers who experience harassment and violence.

  13. ASSEMBLY TRANSFER SYSTEM DESCRIPTION DOCUMENT

    International Nuclear Information System (INIS)

    Gorpani, B.

    2000-01-01

    The Assembly Transfer System (ATS) receives, cools, and opens rail and truck transportation casks from the Carrier/Cask Handling System (CCHS). The system unloads transportation casks consisting of bare Spent Nuclear Fuel (SNF) assemblies, single element canisters, and Dual Purpose Canisters (DPCs). For casks containing DPCs, the system opens the DPCs and unloads the SNF. The system stages the assemblies, transfer assemblies to and from fuel-blending inventory pools, loads them into Disposal Containers (DCs), temporarily seals and inerts the DC, decontaminates the DC and transfers it to the Disposal Container Handling System. The system also prepares empty casks and DPCs for off-site shipment. Two identical Assembly Transfer System lines are provided in the Waste Handling Building (WHB). Each line operates independently to handle the waste transfer throughput and to support maintenance operations. Each system line primarily consists of wet and dry handling areas. The wet handling area includes a cask transport system, cask and DPC preparation system, and a wet assembly handling system. The basket transport system forms the transition between the wet and dry handling areas. The dry handling area includes the dry assembly handling system, assembly drying system, DC preparation system, and DC transport system. Both the wet and dry handling areas are controlled by the control and tracking system. The system operating sequence begins with moving transportation casks to the cask preparation area. The cask preparation operations consist of cask cavity gas sampling, cask venting, cask cool-down, outer lid removal, and inner shield plug lifting fixture attachment. Casks containing bare SNF (no DPC) are filled with water and placed in the cask unloading pool. The inner shield plugs are removed underwater. For casks containing a DPC, the cask lid(s) is removed, and the DPC is penetrated, sampled, vented, and cooled. A DPC lifting fixture is attached and the cask is placed

  14. Optimization of Temperature Level to Enhance Worker Performance in Automotive Industry

    OpenAIRE

    A. R. Ismail; M. Y.M. Yusof; N. K. Makhtar; B. M. Deros; M. R.A. Rani

    2010-01-01

    Problem statement: Production of automotive parts is among the largest contributor to economic earnings in Malaysia. The dominant work involve in producing automotive part were manual assembly process. Where it is definitely used a manpower capability. Thus the quality of the product heavily depends on workers comfort in the working condition. Temperature is one of the environmental factors that give significant effect on the worker performance. Approach: Temperature level and productivity ra...

  15. Assessment of exposure to manganese in welding operations during the assembly of heavy excavation machinery accessories.

    Science.gov (United States)

    Smargiassi, A; Baldwin, M; Savard, S; Kennedy, G; Mergler, D; Zayed, J

    2000-10-01

    Welder exposure to metals in various industrial sectors is poorly characterized. We had the opportunity to carry out an exploratory study to characterize manganese exposure in welding operations in a recently established Quebec factory that assembled accessories for heavy excavation machinery. Ten workers were sampled for total manganese for at least two consecutive days out of three followed by two consecutive days for respirable manganese (with a size selective sampler with a median cut-off of 4 microns), during a typical week in the summer of 1998. Parts being welded were characterized as large or small. Small parts were those being welded on tables during subassembly. Workers were divided into two groups according to the parts they were welding. Seventy-eight percent of the total manganese exposure levels of welding operations during the assembly of large accessories of heavy excavation machinery exceeded the manganese American Conference of Governmental Industrial Hygienists (ACGIH) threshold limit value (TLV) of 0.20 mg/m3 (GM 0.24 mg/m3, n = 14) while none exceeded the TLV during the assembly of small pieces (GM 0.06 mg/m3, n = 8). Welding operations during the assembly of large heavy excavation machinery accessories may pose a significant health hazard. Considering the importance of task-related variables affecting exposure among workers, further studies are needed to better characterize exposure determinants of welding operations during the assembly of heavy excavation machinery accessories.

  16. Simulation and optimization of logistics distribution for an engine production line

    Directory of Open Access Journals (Sweden)

    Lijun Song

    2016-02-01

    Full Text Available Purpose: In order to analyze and study the factors about Logistics distribution system, solve the problems of out of stock on the production line and improve the efficiency of the assembly line. Design/methodology/approach: Using the method of industrial engineering, put forward the optimization scheme of distribution system. The simulation model of logistics distribution system for engine assembly line was build based on Witness software. Findings: The optimization plan is efficient to improve Logistics distribution efficiency, production of assembly line efficiency and reduce the storage of production line Originality/value: Based on the study of the modeling and simulation of engine production logistics distribution system, the result reflects some influence factors about production logistics system, which has reference value to improving the efficiency of the production line.

  17. Fuel assembly inspection device

    International Nuclear Information System (INIS)

    Yaginuma, Yoshitaka

    1998-01-01

    The present invention provides a device suitable to inspect appearance of fuel assemblies by photographing the appearance of fuel assemblies. Namely, the inspection device of the present invention measures bowing of fuel assembly or each of fuel rods or both of them based on the partially photographed images of fuel assembly. In this case, there is disposed a means which flashily projects images in the form of horizontal line from a direction intersecting obliquely relative to a horizontal cross section of the fuel assembly. A first image processing means separates the projected image pictures including projected images and calculates bowing. A second image processing means replaces the projected image pictures of the projected images based on projected images just before and after the photographing. Then, images for the measurement of bowing and images for inspection can be obtained simultaneously. As a result, the time required for the photographing can be shortened, the time for inspection can be shortened and an effect of preventing deterioration of photographing means by radiation rays can be provided. (I.S.)

  18. Causes of electrical deaths and injuries among construction workers.

    Science.gov (United States)

    McCann, Michael; Hunting, Katherine L; Murawski, Judith; Chowdhury, Risana; Welch, Laura

    2003-04-01

    Contact with electrical current is the fourth leading cause of deaths of construction workers. This study evaluates electrical deaths and injuries to construction workers. Two sources of data were analyzed in detail: (1) 1,019 electrical deaths identified by the Bureau of Labor Statistics, Census of Fatal Occupational Injuries (CFOI) for the years 1992-1998; and (2) 61 electrical injuries identified between November 1, 1990 and December 31, 1998 from a George Washington University Emergency Department injury surveillance database. Contact with "live" electrical wiring, equipment, and light fixtures was the main cause of electrical deaths and injuries among electrical workers, followed by contact with overhead power lines. Among non-electrical workers, contact with overhead power lines was the major cause of death. Other causes included contact with energized metal objects, machinery, power tools, and portable lights. Arc flash or blast caused 31% of electrical injuries among construction workers, but less than 2% of electrical deaths. Adoption of a lockout/tagout standard for construction, and training for non-electrical workers in basic electrical safety would reduce the risk of electrical deaths and injuries in construction. Further research is needed on ways to prevent electrical deaths and injuries while working "live". Copyright 2003 Wiley-Liss, Inc.

  19. Apparatus for removing and/or positioning fuel assemblies of a nuclear reactor

    International Nuclear Information System (INIS)

    Vuckovich, M.; Burkett, J.P.; Sallustio, J.

    1983-01-01

    Apparatus for positioning fuel assemblies of a nuclear reactor includes a control for a crane comprising a strain gauge connected to the crane line which raises and lowers the load. The signal from the strain gauge is compared with setpoints; which if the strain gauge signal exceeds a high-level setpoint, indicating that the movement of a fuel assembly is obstructed, the line drive is disabled. The line drive is also disabled if the strain gauge signal is less than a low-level setpoint, indicating that a fuel being deposited contacts the bottom of its slot or an obstruction. To preclude lateral movement of the fuel assembly suspended from the crane line, the traverse drive of the crane is disabled once the strain-gauge signal exceeds the low-level setpoint. The traverse drive can only be enabled after the strain-gauge signal is less than a slack-line setpoint. (author)

  20. Apparatus for removing and/or positioning fuel assemblies of a nuclear reactor

    Energy Technology Data Exchange (ETDEWEB)

    Vuckovich, M; Burkett, J P; Sallustio, J

    1981-11-30

    Apparatus for positioning fuel assemblies of a nuclear reactor includes a control for a crane comprising a strain gauge connected to the crane line which raises and lowers the load. The signal from the strain gauge is compared with setpoints; which if the strain gauge signal exceeds a high-level setpoint, indicating that the movement of a fuel assembly is obstructed, the line drive is disabled. The line drive is also disabled if the strain gauge signal is less than a low-level setpoint, indicating that a fuel being deposited contacts the bottom of its slot or an obstruction. To preclude lateral movement of the fuel assembly suspended from the crane line, the traverse drive of the crane is disabled once the strain-gauge signal exceeds the low-level setpoint. The traverse drive can only be enabled after the strain-gauge signal is less than a slack-line setpoint.

  1. VAGUE: a graphical user interface for the Velvet assembler.

    Science.gov (United States)

    Powell, David R; Seemann, Torsten

    2013-01-15

    Velvet is a popular open-source de novo genome assembly software tool, which is run from the Unix command line. Most of the problems experienced by new users of Velvet revolve around constructing syntactically and semantically correct command lines, getting input files into acceptable formats and assessing the output. Here, we present Velvet Assembler Graphical User Environment (VAGUE), a multi-platform graphical front-end for Velvet. VAGUE aims to make sequence assembly accessible to a wider audience and to facilitate better usage amongst existing users of Velvet. VAGUE is implemented in JRuby and targets the Java Virtual Machine. It is available under an open-source GPLv2 licence from http://www.vicbioinformatics.com/. torsten.seemann@monash.edu.

  2. Method and apparatus for assembling permanent magnet rotors

    Science.gov (United States)

    Hsu, J.S.; Adams, D.J.

    1999-06-22

    A permanent magnet assembly for assembly in large permanent magnet motors and generators includes a two-piece carrier that can be slid into a slot in the rotor and then secured in place using a set screw. The invention also provides an auxiliary carrier device with guide rails that line up with the teeth of the rotor, so that a permanent magnet assembly can be pushed first into a slot, and then down the slot to its proper location. An auxiliary tool is provided to move the permanent magnet assembly into position in the slot before it is secured in place. Methods of assembling and disassembling the magnet assemblies in the rotor are also disclosed. 2 figs.

  3. Patterns of Signs That Telephone Crisis Support Workers Associate with Suicide Risk in Telephone Crisis Line Callers.

    Science.gov (United States)

    Hunt, Tara; Wilson, Coralie; Caputi, Peter; Wilson, Ian; Woodward, Alan

    2018-01-30

    Signs of suicide are commonly used in suicide intervention training to assist the identification of those at imminent risk for suicide. Signs of suicide may be particularly important to telephone crisis-line workers (TCWs), who have little background information to identify the presence of suicidality if the caller is unable or unwilling to express suicidal intent. Although signs of suicide are argued to be only meaningful as a pattern, there is a paucity of research that has examined whether TCWs use patterns of signs to decide whether a caller might be suicidal, and whether these are influenced by caller characteristics such as gender. The current study explored both possibilities. Data were collected using an online self-report survey in a Australian sample of 137 TCWs. Exploratory factor analysis uncovered three patterns of suicide signs that TCWs may use to identify if a caller might be at risk for suicide (mood, hopelessness, and anger), which were qualitatively different for male and female callers. These findings suggest that TCWs may recognise specific patterns of signs to identify suicide risk, which appear to be influenced to some extent by the callers' inferred gender. Implications for the training of telephone crisis workers and others including mental-health and medical professionals, as well as and future research in suicide prevention are discussed.

  4. Measurement of DNA repair deficiency in workers exposed to benzene

    International Nuclear Information System (INIS)

    Hallberg, L.M.; Au, W.W.; El Zein, R.; Grossman, L.

    1996-01-01

    We hypothesize that chronic exposure to environmental toxicants can induce genetic damage causing DNA repair deficiencies and leading to the postulated mutator phenotype of carcinogenesis. To test our hypothesis, a host cell reactivation (HCR) assay was used in which pCMVcat plasmids were damaged with UV light (175, 350 J/m 2 UV light), inactivating the chloramphenicol acetyltransferase reporter gene, and then transfected into lymphocytes. Transfected lymphocytes were therefore challenged to repair the damaged plasmids, reactivating the reporter gene. Xeroderma pigmentosum (XP) and Gaucher cell lines were used as positive and negative controls for the HCR assay. The Gaucher cell line repaired normally but XP cell lines demonstrated lower repair activity. Additionally, the repair activity of the XP heterozygous cell line showed intermediate repair compared to the homozygous XP and Gaucher cells. We used HCR to measure the effects of benzene exposure on 12 exposed and 8 nonexposed workers from a local benzene plant. Plasmids 175 J/m 2 and 350 J/m 2 were repaired with a mean frequency of 66% and 58%, respectively, in control workers compared to 71% and 62% in exposed workers. Conversely, more of the exposed workers were grouped into the reduced repair category than controls. These differences in repair capacity between exposed and control workers were, however, not statistically significant. The lack of significant differences between the exposed and control groups may be due to extremely low exposure to benzene (<0.3 ppm), small population size, or a lack of benzene genotoxicity at these concentrations. These results are consistent with a parallel hprt gene mutation assay. 26 refs., 4 figs., 2 tabs

  5. Self-Sealed Bionic Long Microchannels with Thin Walls and Designable Nanoholes Prepared by Line-Contact Capillary-Force Assembly.

    Science.gov (United States)

    Lao, Zhao-Xin; Hu, Yan-Lei; Pan, Deng; Wang, Ren-Yan; Zhang, Chen-Chu; Ni, Jin-Cheng; Xu, Bing; Li, Jia-Wen; Wu, Dong; Chu, Jia-Ru

    2017-06-01

    Long microchannels with thin walls, small width, and nanoholes or irregular shaped microgaps, which are similar to capillaries or cancerous vessels, are urgently needed to simulate the physiological activities in human body. However, the fabrication of such channels remains challenging. Here, microchannels with designable holes are manufactured by combining laser printing with line-contact capillary-force assembly. Two microwalls are first printed by femtosecond laser direct-writing, and subsequently driven to collapse into a channel by the capillary force that arises in the evaporation of developer. The channel can remain stable in solvent due to the enhanced Van der Waals' force caused by the line-contact of microwalls. Microchannels with controllable nanoholes and almost arbitrary patterns can be fabricated without any bonding or multistep processes. As-prepared microchannels, with wall thicknesses less than 1 µm, widths less than 3 µm, lengths more than 1 mm, are comparable with human capillaries. In addition, the prepared channels also exhibit the ability to steer the flow of liquid without any external pump. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  6. Draft genome of the lined seahorse, Hippocampus erectus.

    Science.gov (United States)

    Lin, Qiang; Qiu, Ying; Gu, Ruobo; Xu, Meng; Li, Jia; Bian, Chao; Zhang, Huixian; Qin, Geng; Zhang, Yanhong; Luo, Wei; Chen, Jieming; You, Xinxin; Fan, Mingjun; Sun, Min; Xu, Pao; Venkatesh, Byrappa; Xu, Junming; Fu, Hongtuo; Shi, Qiong

    2017-06-01

    The lined seahorse, Hippocampus erectus , is an Atlantic species and mainly inhabits shallow sea beds or coral reefs. It has become very popular in China for its wide use in traditional Chinese medicine. In order to improve the aquaculture yield of this valuable fish species, we are trying to develop genomic resources for assistant selection in genetic breeding. Here, we provide whole genome sequencing, assembly, and gene annotation of the lined seahorse, which can enrich genome resource and further application for its molecular breeding. A total of 174.6 Gb (Gigabase) raw DNA sequences were generated by the Illumina Hiseq2500 platform. The final assembly of the lined seahorse genome is around 458 Mb, representing 94% of the estimated genome size (489 Mb by k-mer analysis). The contig N50 and scaffold N50 reached 14.57 kb and 1.97 Mb, respectively. Quality of the assembled genome was assessed by BUSCO with prediction of 85% of the known vertebrate genes and evaluated using the de novo assembled RNA-seq transcripts to prove a high mapping ratio (more than 99% transcripts could be mapped to the assembly). Using homology-based, de novo and transcriptome-based prediction methods, we predicted 20 788 protein-coding genes in the generated assembly, which is less than our previously reported gene number (23 458) of the tiger tail seahorse ( H. comes ). We report a draft genome of the lined seahorse. These generated genomic data are going to enrich genome resource of this economically important fish, and also provide insights into the genetic mechanisms of its iconic morphology and male pregnancy behavior. © The Authors 2017. Published by Oxford University Press.

  7. Portuguese version of the Swedish Occupational Fatigue Inventory (SOFI among assembly workers: Cultural adaptation, reliability and validity

    Directory of Open Access Journals (Sweden)

    Joana Santos

    2017-06-01

    Full Text Available Objectives: Reliable and valid instruments are essential for understanding fatigue in occupational settings. This study analyzed the psychometric properties of the Portuguese version of the Swedish Occupational Fatigue Inventory (SOFI. Material and Methods: A cross-sectional study was conducted with 218 workers from an automotive industry involved in assembly tasks for fabrication of mechanical cables. Convergent and discriminant validity, internal consistency reliability and confirmatory factor analysis were performed. Results: Results showed adequate fit to data, yielding a 20-item, 5-factor structure (all intercorrelated: Chi2/df (ratio Chi2 and degrees of freedom = 2.530, confirmatory fit index (CFI = 0.919, goodness of fit index (GFI = 0.845, root mean square error of approximation (RMSEA = 0.084. The SOFI presented an adequate internal consistency, with the sub-scales and total scale presenting good reliability values (Cronbach’s α values from 0.742 to 0.903 and 0.943 respectively. Conclusions: Findings suggest that the Portuguese version of the SOFI may be a useful tool to assess fatigue and prevent work-related injuries. In future research, other instruments should be used as an external criterion to correlate with the SOFI dimensions. Int J Occup Med Environ Health 2017;30(3:407–417

  8. Assembly and handling apparatus for the EBFA Marx generator

    International Nuclear Information System (INIS)

    Staller, G.E.; Hiett, G.E.; Hamilton, I.D.; Aker, M.F.; Daniels, G.A.

    1979-05-01

    Marx generators, a major slow-pulsed power component in Sandia Laboratories' Electron Beam Fusion Accelerator (EBFA), were assembled at a remote facility modified to utilize an assembly-line technique. Due to the size and weight of the various components, as well as the final Marx generator assembly, special handling apparatus was designed. Time and manpower constraints required that this assembly be done in parallel with the construction of the Electron Beam Fusion Facility (EBFF). The completed Marx generators were temporarily stored and then moved from the assembly building to the EBFF using special transportation racks designed specifically for this purpose

  9. A prototype on-line work procedure system for radioisotope thermoelectric generator production

    International Nuclear Information System (INIS)

    Kiebel, G.R.

    1991-09-01

    An on-line system to manage work procedures is being developed to support radioisotope thermoelectric generator (RTG) assembly and testing in a new production facility. This system implements production work procedures as interactive electronic documents executed at the work site with no intermediate printed form. It provides good control of the creation and application of work procedures and provides active assistance to the worker in performing them and in documenting the results. An extensive prototype of this system is being evaluated to ensure that it will have all the necessary features and that it will fit the user's needs and expectations. This effort has involved the Radioisotope Power Systems Facility (RPSF) operations organization and technology transfer between Westinghouse Hanford Company (Westinghouse Hanford) and EG ampersand G Mound Applied Technologies Inc. (Mound) at the US Department of Energy (DOE) Mound Site. 1 ref

  10. Organizational Justice and Social Workers' Intentions to Leave Agency Positions

    Science.gov (United States)

    Kim, Tae Kuen; Solomon, Phyllis; Jang, Cinjae

    2012-01-01

    The authors investigated the impact of organizational justice on social workers' intention to leave Korean social service agencies. Specifically, this study concentrated on the moderating effect of organizational justice on the relationship between burnout and intention to leave. The authors surveyed 218 front-line social workers from 51 social…

  11. Cooperation between humans and robots in fine assembly

    Science.gov (United States)

    Jalba, C. K.; Konold, P.; Rapp, I.; Mann, C.; Muminovic, A.

    2017-01-01

    The development of ever smaller components in manufacturing processes require handling, assembling and testing of miniature similar components. The human eye meets its optical limits with ongoing miniaturization of parts, due to the fact that it is not able to detect particles with a size smaller than 0.11 mm or register distances below 0.07 mm - like separating gaps. After several hours of labour, workers cannot accurately differentiate colour nuances as well as constant quality of work cannot be guaranteed. Assembly is usually done with tools, such as microscopes, magnifiers or digital measuring devices. Due to the enormous mental concentration, quickly a fatigue process sets in. This requires breaks or change of task and reduces productivity. Dealing with handling devices such as grippers, guide units and actuators for component assembling, requires a time consuming training process. Often productivity increase is first achieved after years of daily training. Miniaturizations are ubiquitously needed, for instance in the surgery. Very small add-on instruments must be provided. In measurement, e.g. it is a technological must and a competitive advantage, to determine required data with a small-as-possible, highest-possible-resolution sensor. Solution: The realization of a flexible universal workstation, using standard robotic systems and image processing devices in cooperation with humans, where workers are largely freed up from highly strenuous physical and fine motoric work, so that they can do productive work monitoring and adjusting the machine assisted production process.

  12. Improvability of assembly systems II: Improvability indicators and case study

    Directory of Open Access Journals (Sweden)

    S.-Y. Chiang

    2000-01-01

    Full Text Available Based on the performance analysis technique developed in Part I, this paper presents improvability indicators for assembly lines with unreliable machines. In particular, it shows that assembly lines are unimprovable with respect to workforce re-distribution if each buffer is, on the average, close to being half full. These lines are unimprovable with respect to buffer capacity re-distribution if each machine is starved and blocked with almost equal frequency. In addition, the paper provides indicators for identification of bottleneck machines and bottleneck buffers. Finally, the paper reports on an application of these improvability indicators in a case study at an automotive components plant.

  13. Multicriteria Analysis of Assembling Buildings from Steel Frame Structures

    Science.gov (United States)

    Miniotaite, Ruta

    2017-10-01

    Steel frame structures are often used in the construction of public and industrial buildings. They are used for: all types of slope roofs; walls of newly-built public and industrial buildings; load bearing structures; roofs of renovated buildings. The process of assembling buildings from steel frame structures should be analysed as an integrated process influenced by such factors as construction materials and machinery used, the qualification level of construction workers, complexity of work, available finance. It is necessary to find a rational technological design solution for assembling buildings from steel frame structures by conducting a multiple criteria analysis. The analysis provides a possibility to evaluate the engineering considerations and find unequivocal solutions. The rational alternative of a complex process of assembling buildings from steel frame structures was found through multiple criteria analysis and multiple criteria evaluation. In multiple criteria evaluation of technological solutions for assembling buildings from steel frame structures by pairwise comparison method the criteria by significance are distributed as follows: durability is the most important criterion in the evaluation of alternatives; the price (EUR/unit of measurement) of a part of assembly process; construction workers’ qualification level (category); mechanization level of a part of assembling process (%), and complexity of assembling work (in points) are less important criteria.

  14. ALARA (As Low As Reasonable Achievable) procedure applied to fuel assembly fabrication with enriched reprocessing uranium (ERU)

    International Nuclear Information System (INIS)

    Guimaraes, Leonam dos Santos; Degrange, Jean Pierre

    1998-01-01

    The study introduced by this paper compose the first step to the implementation of ALARA (As Low As Reasonable Achievable) for a nuclear fuel assembly factory which one of its two production lines will be designed to work with Enriched Reprocessing Uranium (ERU). This step includes the reference situation analysis is based on previsional dosimetric evaluations for individual and collective exposures of each factory operator (117 in total) working on 7 work stations, considering 6 annual production scenarios (10, 50 75, 100 and 150 ERU tons), which corresponds to an annual production of 600 tons (ERU plus enriched natural uranium ENU). The exposure indicators evolution, expressed in terms of collective dose, annual individual dose and radiological detrimental cost for workers, is also used in a complimentary way to guide the analysis. (author)

  15. Fixture for aligning motor assembly

    Science.gov (United States)

    Shervington, Roger M.; Vaghani, Vallabh V.; Vanek, Laurence D.; Christensen, Scott A.

    2009-12-08

    An alignment fixture includes a rotor fixture, a stator fixture and a sensor system which measures a rotational displacement therebetween. The fixture precisely measures rotation of a generator stator assembly away from a NULL position referenced by a unique reference spline on the rotor shaft. By providing an adjustable location of the stator assembly within the housing, the magnetic axes within each generator shall be aligned to a predetermined and controlled tolerance between the generator interface mounting pin and the reference spline on the rotor shaft. Once magnetically aligned, each generator is essentially a line replaceable unit which may be readily mounted to any input of a multi-generator gearbox assembly with the assurance that the magnetic alignment will be within a predetermined tolerance.

  16. Application of a mathematical model for ergonomics in lean manufacturing.

    Science.gov (United States)

    Botti, Lucia; Mora, Cristina; Regattieri, Alberto

    2017-10-01

    The data presented in this article are related to the research article "Integrating ergonomics and lean manufacturing principles in a hybrid assembly line" (Botti et al., 2017) [1]. The results refer to the application of the mathematical model for the design of lean processes in hybrid assembly lines, meeting both the lean principles and the ergonomic requirements for safe assembly work. Data show that the success of a lean strategy is possible when ergonomics of workers is a parameter of the assembly process design.

  17. Resolution No. 43/146. Measures to improve the situation and ensure the human rights and dignity of all migrant workers, 8 December 1988.

    Science.gov (United States)

    1988-01-01

    This document contains portions of the text of a 1988 UN Resolution on measures to improve the situation and ensure the human rights and dignity of all migrant workers. In this resolution, the General Assembly reaffirms international instruments protecting human rights but articulates a further need to improve the protection of human rights for migrant workers and their families. The General Assembly then noted the two most recent reports of the Working Group on the Drafting of an International Convention on the Protection of the Rights of All Migrant Workers and Their Families and took measures to enable the Working Group to complete its task.

  18. [Investigation of noise hazards and hearing status of workers in outdoor quarries].

    Science.gov (United States)

    Zhang, Guoying; Tang, Zhifeng; Yao, Yongping; Wang, Haiying

    2014-08-01

    To investigate the noise hazards in open quarries and to provide a basis for further control of noise hazards. An investigation was performed during 2010 to 2011 among all open quarries in Deqing County of Zhejiang Province, China. The investigation included basic information of the quarries, the occupational health situation and noise intensity at the workplace, and the hearing loss of workers exposed to noise in quarry enterprises. The hearing test results were evaluated based on the Diagnostic criteria of occupational noise-induced hearing loss (GBZ 49-2007). A total of 25 enterprises with open quarries were investigated, of which only 30.4% (17/56) workplaces met the national standard. The median noise level was 92.5 dB (A). Fifty-four (10.6%) out of 508 workers in the 25 enterprises were diagnosed with binaural hearing loss in the initial physical examination, with 18.3% (93/508) under surveillance. The rate of normal hearing among crushing workers, mechanists, drilling workers, and blasting workers ranged between 27.6% and 41.4%, which was significantly lower than that among workers exposed to slight noise hazards (80.0%) or other workers (63.7%) (P drilling workers, and blasting workers most seriously jeopardized. Among crushing workers, those working in the first-line or unprotected second?line positions suffered more than the others. Further measures should be taken by the supervision department and the enterprises to control the noise hazards in open quarries.

  19. Mortality among workers at the Pantex weapons facility

    International Nuclear Information System (INIS)

    Acquavella, J.F.; Wiggs, L.D.; Waxweiler, R.J.; MacDonell, D.G.; Tietjen, G.L.; Wilkinson, G.S.

    1985-01-01

    The authors compared total and cause-specific mortality for workers at the Pantex nuclear weapons assembly facility employed between 1951 and 31 December 1978 with expected mortality based on US death rates. They observed significantly fewer deaths than expected from all causes of death, all cancers, digestive cancers, lung cancer, arteriosclerotic heart disease, and digestive diseases. There were no causes of death which occurred significantly more frequently than expected. Analyses of worker mortality by duration of employment, time since first employment, and radiation exposure greater than 1.00 rem produced similar results. They found no evidence that mortality from any cause of death was increased as a result of employment at Pentex

  20. The Impact of Western Social Workers in Romania - a Fine Line between Empowerment and Disempowerment

    Directory of Open Access Journals (Sweden)

    2004-11-01

    through western grants and individuals. Above and beyond, the presence of western goods and investment in Romania is omnipresent. This reflects a newly-gained freedom and prosperity - Romania profits certainly from these changes. But this is only one side of the medal, as the effect of westernisation contradicts with the Romanian reality and overruns many deep-rooted traditions, thus the majority of people. Moreover, only a small percentage of the population has access to this western world. Western concepts, procedures or interpretations are often highly differing from the Romanian tradition, history and culture. Nevertheless, western ideas seem to dominate the transition in many areas of daily life in Romania. A closer look reveals that many changes take place due to pressure of western governments and are conditioned to financial support. The dialectic relationship between the need for foreign aid and the implementation becomes very obvious in Romania and often leads, despite the substantial benefits, to unpredictable and rather negative side-effects, at a political, social, cultural, ecological and/or economic level. This reality is a huge dilemma for all those involved, as there is a fine line between empowering and disempowering action. It is beyond the scope of this journal to discuss the dilemma posed by Western involvement at all levels; therefore this article focuses on the impact of Western social workers in Romania. The first part consists of a short introduction to social work in Romania, followed by the discussion about the dilemma posed by the structure of project of international social work and the organisation of private social service agencies. Thirdly the experiences of Romanian staff with Western social workers are presented and then discussed with regard to turning disempowering tendencies of Western social workers into empowerment.

  1. Modeling operational behavior of a disassembly line

    Science.gov (United States)

    Kizilkaya, Elif A.; Gupta, Surendra M.

    2004-12-01

    In this paper we present a dynamic kanban (pull) system specifically developed for disassembly lines. This type of kanban system is much more complex than the traditional kanban system used in assembly lines. For instance, unlike the assembly line where the external demand occurs only at the last station, the demands in the disassembly case also occur at any of the intermittent stations. The reason is that as a product moves on the disassembly line, various parts are disassembled at every station and accumulated at that station. Therefore, there are as many demand sources as there are number of parts. We consider a case example involving the end-of-life products. Based on the precedence relationships and other criteria such as hazardous properties of the parts, we balance the disassembly line. The results of the disassembly line-balancing problem (DLBP) are used as input to the proposed dynamic kanban system for disassembly line (DKSDL). We compare the performance of the DKSDL to the modified kanban system for disassembly line (MKSDL), which was previously introduced by the authors. We show, via simulation, that the DKSDL is far superior to MKSDL considered.

  2. Optimal production planning for PCB assembly

    CERN Document Server

    Ho, William

    2006-01-01

    Focuses on the optimization of the Printed circuit board (PCB) assembly lines' efficiency. This book integrates the component sequencing and the feeder arrangement problems together for the pick-and-place machine and the chip shooter machines.

  3. Electrical fatalities among U.S. construction workers.

    Science.gov (United States)

    Ore, T; Casini, V

    1996-06-01

    Over 2000 electrocution deaths were identified among U.S. construction workers from 1980 to 1991, with the highest mean annual crude mortality rate (2.5 per 100,000 people), and second highest mean age-adjusted rate (2.7 per 100,000 people) of all industries. Although the crude fatality rates showed a downward trend, construction workers are still about four times more likely to be electrocuted at work than are workers in all industries combined. Nearly 40% of the 5083 fatal electrocutions in all industries combined occurred in construction, and 80% were associated with industrial wiring, appliances, and transmission lines. Electrocutions ranked as the second leading cause of death among construction workers, accounting for an average of 15% of traumatic deaths in the industry from 1980 to 1991. The study indicates that the workers most at risk of electrical injury are male, young, nonwhite, and electricians, structural metal workers, and laborers. The most likely time of injury is 11 a.m. to 3 p.m. from June to August. Focusing prevention on these populations and characteristics through better methods of worker and supervisor electrical safety training, use of adequate protective clothing, and compliance with established procedures could minimize the average annual loss of 168 U.S. construction workers.

  4. Knowledge and opinions of emergency contraceptive pills among female factory workers in Tijuana, Mexico.

    Science.gov (United States)

    García, Sandra G; Becker, Davida; de Castro, Marcela Martínez; Paz, Francisco; Olavarrieta, Claudia Díaz; Acevedo-García, Dolores

    2008-09-01

    Workers in Mexico's maquiladoras (assembly plants) are mainly young, single women, many of whom could benefit from emergency contraceptive pills (ECPs). Because ECPs are readily available in Mexico, women who know about the therapy can obtain it easily. Do maquiladora workers know about the method? Could worksite programs help increase awareness? To investigate these questions, we conducted a five-month intervention during which workers in three maquiladoras along the Mexico-United States border could attend educational talks on ECPs, receive pamphlets, and obtain kits containing EC supplies. Among the workers exposed to our intervention, knowledge of ECPs increased. Reported ECP use also increased. Although our intervention apparently increased workers' knowledge and use, the factory proved to be a difficult intervention setting. Problems we experienced included a factory closure and management/staff opposition to certain project elements. Future studies should continue to investigate work-site interventions and other strategies to reach workers.

  5. Physical characteristics of GE [General Electric] BWR [boiling-water reactor] fuel assemblies

    International Nuclear Information System (INIS)

    Moore, R.S.; Notz, K.J.

    1989-06-01

    The physical characteristics of fuel assemblies manufactured by the General Electric Company for boiling-water reactors are classified and described. The classification into assembly types is based on the GE reactor product line, the Characteristics Data Base (CDB) assembly class, and the GE fuel design. Thirty production assembly types are identified. Detailed physical data are presented for each assembly type in an appendix. Descriptions of special (nonstandard) fuels are also reported. 52 refs., 1 fig., 6 tabs

  6. 76 FR 81987 - Grupo Antolin, a Subsidiary of Grupo Antolin North America Including Workers Whose Unemployment...

    Science.gov (United States)

    2011-12-29

    ... new projects and any other related activity. Some workers separated from employment at the Belvidere... secondary component supplier to a trade certified primary firm, (Chrysler Assembly Plant, Belvidere...

  7. Upper extremities musculoskeletal disorders: Prevalence and associated ergonomic factors in an electronic assembly factory

    Directory of Open Access Journals (Sweden)

    Somthus Pullopdissakul

    2013-10-01

    Full Text Available Objectives:To determine the magnitude, distribution and associated ergonomic factors of upper extremities musculoskeletal disorders (UEMSD among workers of electronic assembly in Thailand. Material and Methods: This was a cross-sectional study. 591 of 853 workers in an electronic and electrical appliance assembly factory in Bangkok, Thailand, participated in this study. A self-administered questionnaire consisting of demographic data and ergonomic factors was collected from October 2010 to January 2011. Clinical examination of each worker was performed by an occupational physician. The criteria for diagnosis of UEMSD came as a result of a consensus reached by a group of orthopedists. The associated factors were analyzed using a multiple logistic regression. Results: The point prevalence of clinically diagnosed UEMSD was as follows: radial styloid tenosynovitis - 13.03% (95% CI: 10.31-15.75, trigger finger - 9.48% (95% CI: 7.11-11.84, carpal tunnel syndrome - 8.12% (95% CI: 5.91-10.33, lateral epicondylitis - 3.38% (95% CI: 1.92-4.85, and medial epicondylitis - 1.69% (95% CI: 0.65-2.73, respectively. The adjusted odds ratio with statistical significance associated with UEMSD was as follows: high force of wrist - 1.78 (95% CI: 1.06-2.99, awkward posture of wrist - 2.37 (95% CI: 1.28-4.37 and contact stress at wrists - 1.75 (95% CI: 1.02-3.00 to develop radial styloid tenosynovitis. For trigger finger, the ratios were awkward posture of fingers - 2.09 (95% CI: 1.12-3.90 and contact stress on finger - 1.86 (95% CI: 1.04-3.34. For medial epicondylitis, it was an awkward posture of using elbows - 3.14 (95% CI: 1.10-8.95. However, this study did not find any associations between repetitive motion and any UEMSD. Conclusions: UEMSD are most commonly found in electronic assembly workers. The relevant parties should provide comprehensive ergonomic resolution for these workers.

  8. Determination of an Ergonomically Sound Glovebox Glove Port Center Line

    Energy Technology Data Exchange (ETDEWEB)

    Christman, Marissa St John [Los Alamos National Laboratory

    2016-11-30

    Determine an ergonomic glovebox glove port center line location which will be used for standardization in new designs, thus allowing for predictable human work performance, reduced worker exposure to radiation and musculoskeletal injury risks, and improved worker comfort, efficiency, health, and safety.

  9. Determination of an Ergonomically Sound Glovebox Glove Port Center Line

    International Nuclear Information System (INIS)

    Christman, Marissa St; Land, Whitney Morgan

    2016-01-01

    Determine an ergonomic glovebox glove port center line location which will be used for standardization in new designs, thus allowing for predictable human work performance, reduced worker exposure to radiation and musculoskeletal injury risks, and improved worker comfort, efficiency, health, and safety.

  10. PRACTICAL CONTRIBUTIONS TO THE STUDY OF RESISTANCE ASSEMBLIES MADE WITH WARP KNITS

    OpenAIRE

    OANA Ioan-Pavel; OANA Dorina

    2014-01-01

    Based on the principle that a body to be obtained by sewing the material to provide resistance and the like in the stitching assembly, the experimental study of which developed resistance is compared with the resistance materials to effectively assembled by the assembly line. The experimental values resistance for assemblies were obtained in the testing for resistance to sliding stitch ASTM D 434 using Tinius Olsen HK5T test type machine. The assembly strength was determined for warp knit...

  11. No facultative worker policing in the honey bee ( Apis mellifera L.)

    Science.gov (United States)

    Loope, Kevin J.; Seeley, Thomas D.; Mattila, Heather R.

    2013-05-01

    Kin selection theory predicts that in colonies of social Hymenoptera with multiply mated queens, workers should mutually inhibit ("police") worker reproduction, but that in colonies with singly mated queens, workers should favor rearing workers' sons instead of queens' sons. In line with these predictions, Mattila et al. (Curr Biol 22:2027-2031, 2012) documented increased ovary development among workers in colonies of honey bees with singly mated queens, suggesting that workers can detect and respond adaptively to queen mating frequency and raising the possibility that they facultative police. In a follow-up experiment, we test and reject the hypothesis that workers in single-patriline colonies prefer worker-derived males and are able to reproduce directly; we show that their eggs are policed as strongly as those of workers in colonies with multiply mated queens. Evidently, workers do not respond facultatively to a kin structure that favors relaxed policing and increased direct reproduction. These workers may instead be responding to a poor queen or preparing for possible queen loss.

  12. Assembly work in Indonesia and in Sweden--ergonomics, health and satisfaction.

    Science.gov (United States)

    Waluyo, L; Ekberg, K; Eklund, J

    1996-02-01

    Work conditions in industrial production vary substantially between different cultures. In the present study the aims were to identify differences between Swedish and Indonesian assembly industry workers regarding work environment factors, health and job satisfaction, and to find associations between work environment factors, and the health measures. Data were collected by a questionnaire from 326 Swedish and 136 Indonesian assembly industry workers, interviews and from company documents. The prevalence of musculoskeletal symptoms was high in both groups. Stress and psychosomatic symptoms had higher prevalences in the Swedish group, which also rated their work conditions as worse in most respects. Work tasks were physically heavier in Indonesia, but less monotonous and with lower demands on productivity. The Indonesians were more satisfied with their jobs. Physical job demands were associated with musculoskeletal symptoms. Competence development was associated with increased job satisfaction. Conflicts and harassments at work were associated with stress and psychosomatic symptoms. Job pressure, especially deficient planning of the jobs was associated with lower job satisfaction, psychosomatic and stress symptoms in the Swedish group. Implications for job design in the two cultures are presented.

  13. An Evaluation of Google Glass : Design, Implementation and Evaluation of a Product Assembly Application for Google Glass and Smartphones

    OpenAIRE

    Häger, Johan

    2015-01-01

    Assembling components in a production line could potentially be a tedious task, if performed stepwise by the book. However, an employee who is assembling many different products may not know all the steps by heart. As such they will be reliant on an instruction manual. However, an instruction manual must be carried around and, while assembling components, placed in the assembler's line of sight. Instead new technology could make the process more efficient. Google Glass places a display slight...

  14. Self-assembled Nanomaterials for Chemotherapeutic Applications

    Science.gov (United States)

    Shieh, Aileen

    The self-assembly of short designed peptides into functional nanostructures is becoming a growing interest in a wide range of fields from optoelectronic devices to nanobiotechnology. In the medical field, self-assembled peptides have especially attracted attention with several of its attractive features for applications in drug delivery, tissue regeneration, biological engineering as well as cosmetic industry and also the antibiotics field. We here describe the self-assembly of peptide conjugated with organic chromophore to successfully deliver sequence independent micro RNAs into human non-small cell lung cancer cell lines. The nanofiber used as the delivery vehicle is completely non-toxic and biodegradable, and exhibit enhanced permeability effect for targeting malignant tumors. The transfection efficiency with nanofiber as the delivery vehicle is comparable to that of the commercially available RNAiMAX lipofectamine while the toxicity is significantly lower. We also conjugated the peptide sequence with camptothecin (CPT) and observed the self-assembly of nanotubes for chemotherapeutic applications. The peptide scaffold is non-toxic and biodegradable, and drug loading of CPT is high, which minimizes the issue of systemic toxicity caused by extensive burden from the elimination of drug carriers. In addition, the peptide assembly drastically increases the solubility and stability of CPT under physiological conditions in vitro, while active CPT is gradually released from the peptide chain under the slight acidic tumor cell environment. Cytotoxicity results on human colorectal cancer cells and non-small cell lung cancer cell lines display promising anti-cancer properties compared to the parental CPT drug, which cannot be used clinically due to its poor solubility and lack of stability in physiological conditions. Moreover, the peptide sequence conjugated with 5-fluorouracil formed a hydrogel with promising topical chemotherapeutic applications that also display

  15. Improving Energy Efficiency for the Vehicle Assembly Industry: A Discrete Event Simulation Approach

    Science.gov (United States)

    Oumer, Abduaziz; Mekbib Atnaw, Samson; Kie Cheng, Jack; Singh, Lakveer

    2016-11-01

    This paper presented a Discrete Event Simulation (DES) model for investigating and improving energy efficiency in vehicle assembly line. The car manufacturing industry is one of the highest energy consuming industries. Using Rockwell Arena DES package; a detailed model was constructed for an actual vehicle assembly plant. The sources of energy considered in this research are electricity and fuel; which are the two main types of energy sources used in a typical vehicle assembly plant. The model depicts the performance measurement for process- specific energy measures of painting, welding, and assembling processes. Sound energy efficiency model within this industry has two-fold advantage: reducing CO2 emission and cost reduction associated with fuel and electricity consumption. The paper starts with an overview of challenges in energy consumption within the facilities of automotive assembly line and highlights the parameters for energy efficiency. The results of the simulation model indicated improvements for energy saving objectives and reduced costs.

  16. Analysis of the assembling phase of lattice slabs

    Directory of Open Access Journals (Sweden)

    A. L. Sartorti

    Full Text Available Lattice slabs are usual in Brazil. They are formed by precast joists with latticed bars on a base of concrete, and a cover of concrete placed at the jobsite. The assembly of the joists and the filling elements is simple and do not require manpower with great skill, presenting low cost-benefit ratio. However, it is precisely in assembling phase that arise questions related to the scaffold support distance. A mistake in the proper positioning can lead to two undesirable situations. In one of them, a small space between the support lines increases the cost of scaffold, and in other an excessive space can generate exaggerated displacements, and even the collapse of the slab in the stage of concreting. The objective of this work is to analyze the bearing capacity of lattice joists in assembling phase, looking for information that is useful in defining the scaffold support distance. Several joists were tested to define the failure modes and their load bearing capacities. The results allowed to determine equations for calculating the appropriate distance between the support lines of the joists.

  17. Depressão em trabalhadores de linhas elétricas de alta tensão Depression in high voltage power line workers

    Directory of Open Access Journals (Sweden)

    Suerda Fortaleza de Souza

    2012-06-01

    Full Text Available OBJETIVO: Investigar a associação entre desequilíbrio esforços-recompensas no trabalho e sintomas depressivos em trabalhadores de linhas elétricas de alta tensão. MÉTODOS: Estudo de corte transversal realizado em 158 trabalhadores de uma empresa de energia elétrica no Nordeste do Brasil. As dimensões do modelo esforço-recompensa (ERI constituíram as variáveis independentes principais e a variável resposta foi depressão, medida pela escala Center for Epidemiologic Studies Depression (CES-D. Os dados foram analisados com técnicas de regressão logística múltipla. RESULTADOS: Trabalhadores no grupo de baixa recompensa apresentaram prevalência de depressão 6,2 vezes maior em relação àqueles no grupo de alta recompensa. A prevalência de depressão foi 3,3 vezes maior entre os trabalhadores em condição de desequilíbrio esforço-recompensa do que entre aqueles em situação de equilíbrio. CONCLUSÕES: A prevalência de depressão estava fortemente associada às dimensões de esforços e recompensas presentes no trabalho dos eletricitários.OBJECTIVE: To investigate the association between effort-reward imbalance and depressive symptoms among workers in high voltage power lines. METHODS: A cross-sectional study among 158 workers from an electric power company in Northeast Brazil. The main independent variables were the Effort-Reward Imbalance Model (ERI dimensions and the main dependent variable was the prevalence of depression, as measured by the Center for Epidemiologic Studies Depression (CES-D scale. Data were analyzed by multiple logistic regression techniques. RESULTS: The group of low reward workers presented a depression prevalence rate 6.2 times greater than those in the high reward group. The depression prevalence rate was 3.3 greater in workers in the situation of imbalanced effort-reward than in those in effort-reward equilibrium. CONCLUSIONS: The prevalence of depression was strongly associated with psychosocial

  18. The study of postural workload in assembly of furniture upholstery

    Directory of Open Access Journals (Sweden)

    Marek Lasota Andrzej

    2017-01-01

    Full Text Available The productivity of the workers is affected by the Work-related Musculoskeletal Disorders (WRMSDs which common cause of health problems, sick leave and it can result in decreased quality of work and increased absenteeism. The objective of this study is to evaluate and investigate the postural workload of sewing machine operators in the assembly of upholstery in furniture factory by using the Ovako Working Posture Analysing System (OWAS with sampling. The results indicated that posture code 2111 (back code: 2 – bent forward; arms code: 1 – both below the shoulder joint; legs code: 1 – sitting position; load code: – 1 less than 10 kg was the most common working posture rating 38.1%; 63.9% of positions displayed non-neutral back postures and 52% received harmful action categories. The performed assembly tasks have an influence on harmless and harmful action categories. This study is crucial on assembly, and in the future work allows develop a framework for assessment the physical risk of WRMSDs in assembly.

  19. Redesigning assembly stations using ergonomic methods as a lean tool.

    Science.gov (United States)

    Eswaramoorthi, M; John, Mervyn; Rajagopal, C Arjun; Prasad, P S S; Mohanram, P V

    2010-01-01

    With the current state of the global economy, demand for various products plummeting. To sustain in the market, companies have to reduce cost and improve quality. Today, companies have started implementing new philosophies like TQM, TPM, six sigma and lean manufacturing techniques to remain competitive in the market. Lean manufacturing is an emerging philosophy which continuously strives to reduce waste. The main objective of analyzing the assembly line with a lean perspective is to identify the areas related to human interface with other systems that could lead to the generation of waste. Improper workplace design leads to unreasonable mental or physical burden and results in waste generation like slow work (delay and inventory), and defects, which is named as muri waste. An attempt has been made in this paper to locate muri waste and create a "Lean assembly line". The proposed method, based on the use of Rapid Upper Limb Assessment (RULA) with CATIA V5 platform, has allowed the measurement of a large set of operator posture parameters and assessment of ergonomic stresses. Based on the results, the process stations in the assembly line were redesigned to prevent the generation of waste.

  20. Remediation workers' exposure assessment feasibility study at the Department of Energy's Mound Site: Phase 1

    International Nuclear Information System (INIS)

    Stevens, G.W.; Back, D.A.

    1997-10-01

    The Department of Health and Human Services (DHHS), subsequent to the implementation of a Memorandum of Understanding (MOU) between the Departments of Energy (DOE) and Health and Human Services, conducts a program of independent occupational and environmental research studies with funding from DOE. This document on the DOE Mound site represents the second background site document prepared for the development of the NIOSH project entitled: Exposure Assessment of Hazardous Waste (HW), Decontamination (De), Dismantlement (Di), and Clean Up Workers (CW). The purpose of this document is to assemble information relevant to Remediation Workers performing HW, De, Di, and CW task activities at the DOE Mound site addressing four primary objectives. The objectives are: identification of Remediation Workers performing HW, De, Di, and CW task activities anticipated or in progress from the recent past through the next five to 10 years; demographic definition of the workforce performing these activities; identification of the technologies in use or proposed to be used (including considerations regarding health and safety impact upon the workforce); and assembly of summary information for potential chemical, mixed, and radiological contaminant exposure that may be encountered during these processes

  1. Banking, Technology Workers and Their Career Development.

    Science.gov (United States)

    Armstrong, Lesley; West, Jim

    2001-01-01

    An Australian bank developed a four-stage career development strategy for information technology workers: (1) career coaching sessions with executives; (2) career coaching seminars for line managers and team leaders; (3) staff career planning workshops; and (4) online career development support. The program resulted in increased satisfaction,…

  2. NIF Laser Line Replaceable Units (LRUs)

    International Nuclear Information System (INIS)

    Larson, D W

    2003-01-01

    The National Ignition Facility (NIF) is designed with its high value optical systems in cassettes called Line Replaceable Units (LRUs). Virtually all of the NIF's active components are assembled in one of the ∼4000 electrical and optical LRUs that serve between two and eight of NIF's 192 laser beam lines. Many of these LRUs are optomechanical assemblies that are roughly the size of a telephone booth. The primary design challenges for this hardware include meeting stringent mechanical precision, stability and cleanliness requirements. Pre-production units of each LRU type have been fielded on the first bundle of NIF and used to demonstrate that NIF meets its performance objectives. This presentation provides an overview of the NIF LRUs, their design and production plans for building out the remaining NIF bundles

  3. Framework to Implement Collaborative Robots in Manual Assembly: A Lean Automation Approach

    DEFF Research Database (Denmark)

    Malik, Ali Ahmad; Bilberg, Arne

    The recent proliferation of smart manufacturing technologies has emerged the concept of hybrid automation for assembly systems utilizing the best of humans and robots in a combination. Based on the ability to work alongside human-workers the next generation of industrial robots (or robotics 2...... of virtual simulations is discussed for validation and optimization of human-robot work environment....

  4. Recipe-Based Engineering and Operator Support for Flexible Configuration of High-Mix Assembly

    NARCIS (Netherlands)

    Verhoosel, J.P.C.; Bekkum, M.A. van

    2017-01-01

    Nowadays, manufacturers must be increasingly flexible to quickly produce a high mix of on-demand, customer-specific, low volume product types. This requires flexible assembly lines with operators that are well-supported in their constantly changing assembly task, while producing high-quality,

  5. Calculation of drop course of control rod assembly in PWR

    International Nuclear Information System (INIS)

    Zhou Xiaojia; Mao Fei; Min Peng; Lin Shaoxuan

    2013-01-01

    The validation of control rod drop performance is an important part of safety analysis of nuclear power plant. Development of computer code for calculating control rod drop course will be useful for validating and improving the design of control rod drive line. Based on structural features of the drive line, the driving force on moving assembly was analyzed and decomposed, the transient value of each component of the driving force was calculated by choosing either theoretical method or numerical method, and the simulation code for calculating rod cluster control assembly (RCCA) drop course by time step increase was achieved. The analysis results of control rod assembly drop course calculated by theoretical model and numerical method were validated by comparing with RCCA drop test data of Qinshan Phase Ⅱ 600 MW PWR. It is shown that the developed RCCA drop course calculation code is suitable for RCCA in PWR and can correctly simulate the drop course and the stress of RCCA. (authors)

  6. Promoting job safety for workers with intellectual disabilities: the staying safe at work training curriculum.

    Science.gov (United States)

    Dewey, Robin

    2011-01-01

    In the United States, approximately 125,000 people with disabilities are employed through Community Rehabilitation Programs in manufacturing, assembly, and service jobs. These jobs have significant hazards and, consequently, the workers are at risk of injury. Training that empowers workers to participate in prevention efforts can help reduce work-related injuries. In general this kind of health and safety training in the United States is limited. It is even more so for workers with intellectual disabilities, in part because there have not been programs for teaching individuals with cognitive challenges health and safety skills, adapted to their learning needs. This paper describes the development and promotion of the Staying Safe at Work curriculum of UC Berkeley's Labor Occupational Health Program, which is designed for use by support agencies and employers of workers with intellectual disabilities. The goal of this program is to teach these workers essential occupational safety and health skills in a manner they can understand.

  7. A preliminary study of reproductive outcomes of female maquiladora workers in Tijuana, Mexico.

    Science.gov (United States)

    Eskenazi, B; Guendelman, S; Elkin, E P; Jasis, M

    1993-12-01

    Maquiladoras are plants on the Mexican side of the United States-Mexico border which are used largely by U.S. manufacturers to assemble premanufactured parts. We examined reproductive outcomes of women employed in electronics (N = 120) and garment (N = 121) maquiladora work compared to women employed in the service sector (N = 119) in Tijuana, Mexico. Women recruited by community health workers were interviewed about their reproductive history, sociodemographic characteristics, health behaviors, and characteristics of their current job. Length of regular menstrual cycle in the past year as well as time of conception and rates of fetal loss in the most recent pregnancy were similar across occupational groups. However, infants of garment maquiladora workers were 653 g lighter (95% confidence interval [CI]: -1,041 g, -265 g) and infants of electronic maquiladora workers were 337 g lighter (95% CI: -682 g, 9 g) than infants of service workers after adjusting for potential confounders. The cause of these differences remains unclear.

  8. Intersecting Work and Learning: Assembling Advanced Liberal Regimes of Governing Workers in Australia

    Science.gov (United States)

    Reich, Ann

    2008-01-01

    Much had been written over the past few years on the intersections of work and learning. This article suggests that the analysis of the intersections of work and learning can benefit greatly from understanding the ways in which governing workers as individuals and populations has changed in Western liberal democracies in the latter part of the…

  9. The assembly and use of continuous flow systems for chemical synthesis.

    Science.gov (United States)

    Britton, Joshua; Jamison, Timothy F

    2017-11-01

    The adoption of and opportunities in continuous flow synthesis ('flow chemistry') have increased significantly over the past several years. Continuous flow systems provide improved reaction safety and accelerated reaction kinetics, and have synthesised several active pharmaceutical ingredients in automated reconfigurable systems. Although continuous flow platforms are commercially available, systems constructed 'in-lab' provide researchers with a flexible, versatile, and cost-effective alternative. Herein, we describe the assembly and use of a modular continuous flow apparatus from readily available and affordable parts in as little as 30 min. Once assembled, the synthesis of a sulfonamide by reacting 4-chlorobenzenesulfonyl chloride with dibenzylamine in a single reactor coil with an in-line quench is presented. This example reaction offers the opportunity to learn several important skills including reactor construction, charging of a back-pressure regulator, assembly of stainless-steel syringes, assembly of a continuous flow system with multiple junctions, and yield determination. From our extensive experience of single-step and multistep continuous flow synthesis, we also describe solutions to commonly encountered technical problems such as precipitation of solids ('clogging') and reactor failure. Following this protocol, a nonspecialist can assemble a continuous flow system from reactor coils, syringes, pumps, in-line liquid-liquid separators, drying columns, back-pressure regulators, static mixers, and packed-bed reactors.

  10. Capillary Assembly of Colloids: Interactions on Planar and Curved Interfaces

    Science.gov (United States)

    Liu, Iris B.; Sharifi-Mood, Nima; Stebe, Kathleen J.

    2018-03-01

    In directed assembly, small building blocks are assembled into an organized structure under the influence of guiding fields. Capillary interactions provide a versatile route for structure formation. Colloids adsorbed on fluid interfaces distort the interface, which creates an associated energy field. When neighboring distortions overlap, colloids interact to minimize interfacial area. Contact line pinning, particle shape, and surface chemistry play important roles in structure formation. Interface curvature acts like an external field; particles migrate and assemble in patterns dictated by curvature gradients. We review basic analysis and recent findings in this rapidly evolving literature. Understanding the roles of assembly is essential for tuning the mechanical, physical, and optical properties of the structure.

  11. Stable producer cell lines for adeno-associated virus (AAV) assembly.

    Science.gov (United States)

    Chadeuf, Gilliane; Salvetti, Anna

    2010-10-01

    Stable producer cell lines containing both the rep and cap genes and recombinant adeno-associated virus (rAAV) vectors can be infected with a helper virus to provide reliable and efficient production of rAAV stocks. However, the development of these cell lines is time-consuming. The procedure described here is therefore recommended only for studies requiring the production of high amounts of rAAV, such as preclinical studies performed in large animals.

  12. ATLAS facility fabrication and assembly

    CERN Document Server

    Ballard, E O; Davis, H A; Nielsen, K E; Parker, G V; Parsons, W M

    2001-01-01

    Summary form only given. Atlas is a pulsed-power facility recently completed at Los Alamos National Laboratory to drive hydrodynamic experiments. This new generation pulsed-power machine consists of a radial array of 24, 240-kV Marx modules and transmission lines supplying current to the load region at the machine center. The transmission lines, powered by the Marx modules, consist of cable headers, load protection switches and tri-plates interfacing to the center transition section through detachable current joints. A conical power-flow-channel attaches to the transition section providing an elevated interface to attach the experimental loads for diagnostic access. Fabrication and assembly of all components for the Atlas machine was completed in August 2000. The machine has also progressed through a test phase where the Marx module/transmission line units were fired, individually, into a test load. Progression continued with eight and sixteen lines being fired. Subsequently, an overall machine test was condu...

  13. [Results of risk and impairment assessment in groups of workers exposed to repetitive strain and movement of the upper limbs in various sectors of industry].

    Science.gov (United States)

    Colombini, Daniela; Occhipinti, E

    2004-01-01

    This presents study the results of a number of investigations regarding risks associated with biomechanical overload of the upper limbs and the consequent health effects (UL-WMSDs) in a large sample of workers in various different jobs. Risk assessment regarded 15 different working environments in which 4044 subjects were employed. Most were metalworking factories in which the workers performed assembly tasks (3015 workers). Some made motors for electrical appliances (714 workers), others assembled miniature components (shock absorbers and remote controls: 259 workers), while others handled larger sized parts such as components of large domestic appliances (refrigerators, freezers, ovens: 2037 workers). The sample also included workers in the meat processing industry (chicken and turkey, 969 workers) and hotel room cleaners (60). Exposure assessment was performed using the OCRA checklist for quantifying the risk attributable intrinsically to each individual workstation, as if used for the entire shift. The values thus obtained were entered into a special software program that, for each working area, produced mean weighted values for the results of the checklist and their percentage distribution over four categories: no risk (green), low risk (yellow), moderate risk (red) and high risk (purple). In 11 of the 15 working environments considered, a total of 3511 workers (2221 women and 1290 men) underwent a complete and standardized clinical examination of the upper limbs. Comparisons of the results of exposure evaluation and of the clinical surveys were made between the different types of jobs and between males and females.

  14. Manufacturing system design based on axiomatic design: Case of assembly line

    Energy Technology Data Exchange (ETDEWEB)

    Hager, T.; Wafik, H.; Faouzi, M.

    2017-07-01

    In this paper, a combined Production Line Design (PLD) process which includes many design aspects is presented, developed and validated. Design/methodology/approach: The PLD process is based on the SADT (Structured Analysis and Design Technique) diagram and the Axiomatic Design (AD) method. Practical implications: For a purpose of validation, this proposed process has been applied in a manufacturing company and it has been validated by simulation. Findings: The results of the validation indicated that the production line designed by this process is outperformed the initial line of the company. Originality/value: Recently, the problems of production line design (PLD) have attracted the attention of many researchers. However, only a few studies have treated the PLD which includes all design aspects. In this work, a combined PLD process is presented. It should be noted that the proposed process is simple and effective.

  15. Manufacturing system design based on axiomatic design: Case of assembly line

    International Nuclear Information System (INIS)

    Hager, T.; Wafik, H.; Faouzi, M.

    2017-01-01

    In this paper, a combined Production Line Design (PLD) process which includes many design aspects is presented, developed and validated. Design/methodology/approach: The PLD process is based on the SADT (Structured Analysis and Design Technique) diagram and the Axiomatic Design (AD) method. Practical implications: For a purpose of validation, this proposed process has been applied in a manufacturing company and it has been validated by simulation. Findings: The results of the validation indicated that the production line designed by this process is outperformed the initial line of the company. Originality/value: Recently, the problems of production line design (PLD) have attracted the attention of many researchers. However, only a few studies have treated the PLD which includes all design aspects. In this work, a combined PLD process is presented. It should be noted that the proposed process is simple and effective.

  16. [A survey of occupational health among polyether-exposed workers].

    Science.gov (United States)

    Fu, Xu-ying; Yu, Bin; Zhang, Chun-ping; Zheng, Guan-hua; Bai, Lan; Zhang, Pan-pan

    2013-06-01

    To investigate the occupational health of the workers simultaneously exposed to acrylonitrile, epoxyethane, epoxypropane, and styrene. A questionnaire survey was conducted in 70 front-line workers simultaneously exposed to acrylonitrile, epoxyethane, epoxypropane, and styrene (exposure group) and 50 managers (control group) in a polyether manufacturer; in addition, air monitoring at workplace and occupational health examination were also performed. The obtained data were analyzed. The female workers in exposure group and the spouses of male workers in exposure group had significantly higher spontaneous abortion rates than their counterparts in control group (P polyether-exposed working years had significantly higher mean levels of DNA damage than the control group (P polyether-exposed working years and those with not less than 20 polyether-exposed working years had significantly higher mean micronucleus rates than the control group (P polyether-exposed working years (P > 0.05); the workers with not less than 5 and less than 20 polyether-exposed working years and workers with not less than 20 polyether-exposed working years had significantly higher mean micronucleus rates than those with less than 5 polyether-exposed working years (P polyether manufacturer.

  17. Job quality of short-time workers and perception and support from their managers

    OpenAIRE

    坂爪, 洋美

    2017-01-01

    The purpose of this study was to clarify the relationship between the characteristics of job quality that short-time workers occupied and the managers’ perception and support whose member has used short-time working hour system. A total of 559 first-line managers who has a member using short-time working hour system completed a web-based survey assessing job quality of short-time workers , the risk of using short-timeworking hour system, career perspective of short-time workers, and the suppo...

  18. LFI Radiometric Chain Assembly (RCA) data handling ``Rachel''

    Science.gov (United States)

    Malaspina, M.; Franceschi, E.; Battaglia, P.; Binko, P.; Butler, R. C.; D'Arcangelo, O.; Fogliani, S.; Frailis, M.; Franceschet, C.; Galeotta, S.; Gasparo, F.; Gregorio, A.; Lapolla, M.; Leonardi, R.; Maggio, G.; Mandolesi, N.; Manzato, P.; Maris, M.; Meharga, M.; Meinhold, P.; Morisset, N.; Pasian, F.; Perrotta, F.; Rohlfs, R.; Sandri, M.; Tomasi, M.; Türler, M.; Zacchei, A.; Zonca, A.

    2009-12-01

    Planck's Low Frequency Instrument is an array of 22 pseudo-correlation radiometers at 30, 44, and 70 GHz. Before integrating the overall array assembly, a first set of tests has been performed for each radiometer chain assembly (RCA), consisting of two radiometers. In this paper, we describe Rachel, a software application which has been purposely developed and used during the RCA test campaign to carry out both near-realtime on-line data analysis and data storage (in FITS format) of the raw output from the radiometric chains.

  19. LFI Radiometric Chain Assembly (RCA) data handling 'Rachel'

    International Nuclear Information System (INIS)

    Malaspina, M; Franceschi, E; Butler, R C; Mandolesi, N; Battaglia, P; Franceschet, C; Lapolla, M; Binko, P; Meharga, M; D'Arcangelo, O; Fogliani, S; Frailis, M; Galeotta, S; Gasparo, F; Maggio, G; Manzato, P; Maris, M; Gregorio, A; Leonardi, R; Meinhold, P

    2009-01-01

    Planck's Low Frequency Instrument is an array of 22 pseudo-correlation radiometers at 30, 44, and 70 GHz. Before integrating the overall array assembly, a first set of tests has been performed for each radiometer chain assembly (RCA), consisting of two radiometers. In this paper, we describe Rachel, a software application which has been purposely developed and used during the RCA test campaign to carry out both near-realtime on-line data analysis and data storage (in FITS format) of the raw output from the radiometric chains.

  20. Device for transferring fast nuclear reactor fuel assemblies

    International Nuclear Information System (INIS)

    Plagnard, Andre.

    1982-01-01

    The description is given of a device for transferring fuel assemblies between a storage position near the reactor vessel and a position where the irradiated assemblies are evacuated and the provision of new assemblies for the reactor. This device can be dismantled and is movable as a whole for its successive use on several reactors and includes: - a platform mounted so as to rotate on a support made to rest on the structure of the reactor, the platform having at least one opening then being horizontal and mobile about a vertical axis to bring the opening successively in position with vertical wells giving access to the storage and evacuation positions of the assemblies provided in the reactor structure, - at least one hopper that can contain one assembly in a vertical position, located on the upper surface of the platform around the opening provided in it and fitted with a winch for the vertical moving of the assemblies inside the wells and the hopper, when these follow each other by rotation of the platform, - at least one connecting device carried on the platform for connecting the hopper and wells when these are in line [fr

  1. The ILO and the new UN convention on migrant workers: the past and future.

    Science.gov (United States)

    Bohning, R

    1991-01-01

    Migrant workers are less protected than nationals against the actions of states and employers. These workers therefore require special global protection of their rights while employed in countries other than their own. Accordingly, the UN International Labor Organization (ILO) is constitutionally charged with developing international measures to protect the interests of migrant workers from developing countries. The ILO, however, had little involvement in molding the International Convention on the protection of the Rights of All Migrants Workers and Members of their Families, adopted by the UN General Assembly in 1990. Instead, final adoption of the Convention stems largely from developing state dissatisfaction with the former 1975 ILO Migrant Workers Convention No. 143, and Mexican and Moroccan government machinations outside of the ILO in support of modifications. Convention No. 143 threatened to sever employment opportunities and hard foreign exchange remittances in North America and western Europe from illegally employed immigrant workers from developing countries. By working in the UN outside of the ILO, developing nations would enjoy automatic majority, and greater potential for success in reforming the Convention. Soon, developing nations squelched a delay tactic proffered by the Swedes, and succeeded in bringing the UN General Assembly to adopt resolution 34/172 in December 1979, which led to the establishment of an Open-Ended Working Group. This group then elaborated the 1990 Convention over 19 sessions. At the expense of the ILO and more developed nations, developing nations successfully challenged and changed the international order to benefit their peoples and national economies. Finally, the paper considers the interests of immigrant businesspeople and asylum seekers during or immediately upon entry to a foreign country, who are not specifically covered by the Convention. While the university of international humanitarian law suggests that

  2. Development Of Lean Assembly Line – A Case Study

    Directory of Open Access Journals (Sweden)

    D. Rajenthirakumar

    2014-12-01

    Full Text Available This paper describes the implementation of lean tools in a wind mill-electrical control panel assembly plant in south India as a lean manufacturing improvement initiative. This involved mapping the activities of the firm, identifying opportunities for improvement and then undertaking with the firm an improvement programme. Current state map is prepared to describe the existing position and various problem areas. Takt time calculations are carried out to set the pace of production. Future state map is prepared to show the proposed improvement action plans. The achievements of value stream implementation are reduction in lead time, cycle time and inventory level. It was found that even a small company can make significant improvements by adopting lean principles.

  3. Software development for on-line computation with PDP 15/76 computer

    Energy Technology Data Exchange (ETDEWEB)

    Viyogi, Y P; Bhattacharjee, T K; De, S K; Basu, A K; Ganguly, N K [Bhabha Atomic Research Centre, Bombay (India). Variable Energy Cyclotron Project

    1979-01-01

    Two important capabilities have been incorporated in the on-line data processing system for the pulse height analysis at VEC, for the processing of data by using codes PHA1 and PHA2, the single parameter and dual parameter data acquisition programs. (1) RDMA is written in assembly language for randomly accessing any element of data from data filing devices. This increases the availability of core so that capability of processing programs can be enhanced. (2) PHARAD, also written in assembly language, converts data files created by acquisition programs into FORTRAN compatible files. These are very essential for on-line processing of data. The on-line data acqujsition and processing by PDP 15/76 using these facilities are discussed.

  4. Constitutive Cdk2 activity promotes aneuploidy while altering the spindle assembly and tetraploidy checkpoints

    DEFF Research Database (Denmark)

    Jahn, Stephan C; Corsino, Patrick E; Davis, Bradley J

    2013-01-01

    instability. Expression of these complexes in the MCF10A cell line leads to retinoblastoma protein (Rb) hyperphosphorylation, a subsequent increase in proliferation rate, and increased expression of the spindle assembly checkpoint protein Mad2. This results in a strengthening of the spindle assembly...

  5. Fuel assembly

    International Nuclear Information System (INIS)

    Chaki, Masao; Nishida, Koji; Karasawa, Hidetoshi; Kanazawa, Toru; Orii, Akihito; Nagayoshi, Takuji; Kashiwai, Shin-ichi; Masuhara, Yasuhiro

    1998-01-01

    The present invention concerns a fuel assembly, for a BWR type nuclear reactor, comprising fuel rods in 9 x 9 matrix. The inner width of the channel box is about 132mm and the length of the fuel rods which are not short fuel rods is about 4m. Two water rods having a circular cross section are arranged on a diagonal line in a portion of 3 x 3 matrix at the center of the fuel assembly, and two fuel rods are disposed at vacant spaces, and the number of fuel rods is 74. Eight fuel rods are determined as short fuel rods among 74 fuel rods. Assuming the fuel inventory in the short fuel rod as X(kg), and the fuel inventory in the fuel rods other than the short fuel rods as Y(kg), X and Y satisfy the relation: X + Y ≥ 173m, Y ≤ - 9.7X + 292, Y ≤ - 0.3X + 203 and X > 0. Then, even when the short fuel rods are used, the fuel inventory is increased and fuel economy can be improved. (I.N.)

  6. Assembly of laboratory line for nuclear fuel reprocessing

    International Nuclear Information System (INIS)

    Fidler, J.; Chotivka, V.

    1979-01-01

    The dismantling of a laboratory line for spent fuel reprocessing after the termination of the research programme and the procedures for hot and semi-hot cell decontamination are described. The equipment was mostly disassembled in smaller parts which were then decontaminated by wiping them with cotton wool soaked in detergent and citric acid, varnished with two-component epoxi varnish, wrapped into multiple polyethylene foils, sealed in PVC bags and thus ready for transport. (B.S.)

  7. Fire Extinguisher Training for Fire Watch and Designated Workers, Course 9893

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Jimmy D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-04-19

    At Los Alamos National Laboratory (LANL), all workers must be aware of LANL fire protection policies and be trained on what to do in the event of a fire. This course, Fire Extinguisher Training for Fire Watch and Designated Workers (#9893), provides awareness-level and hands-on training for fire watch personnel and designated workers. Fire watch personnel and designated workers are appointed by line management and must receive both awareness-level training and hands-on training in the use of portable fire extinguishers to extinguish an incipient-stage fire. This training meets the requirements of the Occupational Safety and Health Administration (OSHA) Code of Federal Regulations (CFR) 29 CFR 1910.157, Portable Fire Extinguishers, and Procedure (P) 101-26, Welding, Cutting, and Other Spark-/Flame-Producing Operations.

  8. Fire Extinguisher Designated Worker and Fire Watch: Self-Study Course 15672

    Energy Technology Data Exchange (ETDEWEB)

    Harris, Jimmy D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-07-08

    At Los Alamos National Laboratory (LANL), all workers must be aware of LANL fire protection policies and be trained on what to do in the event of a fire. This course, Fire Extinguisher Training for Fire Watch and Designated Workers (#9893), provides awareness-level and hands-on training for fire watch personnel and designated workers. Fire watch personnel and designated workers are appointed by line management and must receive both awareness-level training and hands-on training in the use of portable fire extinguishers to extinguish an incipient-stage fire. This training meets the requirements of the Occupational Safety and Health Administration (OSHA) Code of Federal Regulations (CFR) 29 CFR 1910.157, Portable Fire Extinguishers, and Procedure (P) 101-26, Welding, Cutting, and Other Spark-/Flame-Producing Operations.

  9. 77 FR 19718 - Ford Motor Company Twin Cities Assembly Plant Vehicle Operations Division Including On-Site...

    Science.gov (United States)

    2012-04-02

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-81,038] Ford Motor Company Twin... February 9, 2012, applicable to workers of Ford Motor Company, Twin Cities Assembly Plant, Vehicle..., and Pacer International were employed on-site at the St. Paul, Minnesota location of Ford Motor...

  10. From self-organization to self-assembly: a new materialism?

    Science.gov (United States)

    Vincent, Bernadette Bensaude

    2016-09-01

    While self-organization has been an integral part of academic discussions about the distinctive features of living organisms, at least since Immanuel Kant's Critique of Judgement, the term 'self-assembly' has only been used for a few decades as it became a hot research topic with the emergence of nanotechnology. Could it be considered as an attempt at reducing vital organization to a sort of assembly line of molecules? Considering the context of research on self-assembly I argue that the shift of attention from self-organization to self-assembly does not really challenge the boundary between chemistry and biology. Self-assembly was first and foremost investigated in an engineering context as a strategy for manufacturing without human intervention and did not raise new perspectives on the emergence of vital organization itself. However self-assembly implies metaphysical assumptions that this paper tries to disentangle. It first describes the emergence of self-assembly as a research field in the context of materials science and nanotechnology. The second section outlines the metaphysical implications and will emphasize a sharp contrast between the ontology underlying two practices of self-assembly developed under the umbrella of synthetic biology. And unexpectedly, we shall see that chemists are less on the reductionist side than most synthetic biologists. Finally, the third section ventures some reflections on the kind of design involved in self-assembly practices.

  11. Haiti. Educating factory workers.

    Science.gov (United States)

    Hughes, H

    1990-04-01

    There are approximately 50,000 workers employed in the light assembly industry in Haiti. About 70% are women, the majority of whom are aged between 25 and 34 years, and are either single or in a nonpermanent relationship with the father of their children. Many live and work in appalling conditions, surviving on very low wages to support several children and an extended family. The acquired immunodeficiency syndrome (AIDS) is now a visible problem in many factories. In October 1988, the Center for the Promotion of Women Workers (Centre de Promotion des Femmes Ouvriers/CPFO) launched a pilot AIDS education program for factory women. The Center, based in a large industrial zone near the airport, runs a health clinic and courses in literacy, communications skills, health promotion and family planning. The new AIDS program allowed CPFO staff to gain entry into factories for the 1st time. Other courses were held outside working hours and outside factory premises. Staff contacted manages by telephone to arrange a meeting to discuss AIDS and to ask permission to hold educational "round tables" with workers. Of 18 managers in the factories approached over a 12-month period, only 2 refused entry to CPFO staff. Almost all managers reported they had registered between 2 and 5 deaths from AIDS among their employees over the past couple of years. A total of 85 educational sessions, each lasting about 2 hours, were held within 28 different factories, community or labor organizations reaching 3063 workers (male and female). In each session, the presentation was carried out by 2 CPFO trained monitors and included a slide show, flip charts, and the video "Met ko," originally produced for Haitian immigrants in New York. The most important aspect of the program was the training of 38 volunteer factory-based health promoters. These promoters attended the round table sessions, where they facilitated discussion and distributed condoms and were subsequently available for counseling co-workers

  12. The study of postural workload in assembly of furniture upholstery

    OpenAIRE

    Marek Lasota Andrzej; Hankiewicz Krzysztof

    2017-01-01

    The productivity of the workers is affected by the Work-related Musculoskeletal Disorders (WRMSDs) which common cause of health problems, sick leave and it can result in decreased quality of work and increased absenteeism. The objective of this study is to evaluate and investigate the postural workload of sewing machine operators in the assembly of upholstery in furniture factory by using the Ovako Working Posture Analysing System (OWAS) with sampling. The results indicated that posture code ...

  13. 'On line' course for the periodical training in radiological safety of the workers of a radioactive facility

    International Nuclear Information System (INIS)

    Amador B, Z.H.; Ayra P, F.E.; Torres B, M.B.

    2006-01-01

    The results of an 'on line' course for the periodical training in radiological safety of the workers of a radioactive installation are presented. The course is developed for own specialists. The following topics are approached: the state of the art of the studies on the biological effects of the ionizing radiations, the new national regulations, the analysis of the behavior of the occupational exposure, of the obtained experiences of the radiological events, of the results of the radiological surveillance of the work positions, of the detected violations and of the behavior of the outstanding systems and the optimization. The study of the acquired experiences in the packing and the transportation of radioactive materials and the administration of the radioactive waste are included. The study of the course by one month is organized and then two convocations of theoretical exams are executed and one for the evaluation practices of the instructions and procedures. To evaluate the effectiveness of the course a survey it is applied and the later behavior of indicators of the radiological safety of the plant is analyzed. The results that are obtained show a positive balance. (Author)

  14. 75 FR 3253 - Lamb Assembly and Test, LLC, Subsidiary of Mag Industrial Automation Systems, Machesney Park, IL...

    Science.gov (United States)

    2010-01-20

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-70,516] Lamb Assembly and Test, LLC, Subsidiary of Mag Industrial Automation Systems, Machesney Park, IL; Notice of Negative... workers of Lamb Technicon, a division of Unova, Warren, Michigan and Lake Orion, Michigan were previously...

  15. IMPROVEMENT FOR AN ASSEMBLY FLOW FOR A GIVEN COMPONENT (1

    Directory of Open Access Journals (Sweden)

    Ancuţa BĂLTEANU,

    2017-05-01

    Full Text Available This study is carried out in a line of assembly of a finite wiring product. The assembly of this finished product is done in two specific sections. For the analysis of the activities in the assembly section, the timing method of the work stations was used. On the basis of the work times obtained and their centralization, the Keizen method was subsequently applied to obtain an improvement in the installation flow. Finally, a reduction in working times was achieved, as well as a more ergonomic arrangement of jobs. This paper is the first in a series of 3 papers to deal with this subject.

  16. Armor: An αβγ assembly for irradiated fuel analysis

    International Nuclear Information System (INIS)

    Beraud, M.

    1967-04-01

    The assembly ARMOR which was built with a view to carrying out research on irradiated fuels consists of an αβγ enclosure made up of 11 cells in line. After a general description of the assembly in its present form, the various functions are reviewed: introduction of the samples, chemical de-canning, dissolution of the irradiated uranium pellets, preparation of solutions for mass spectrometric analyses, disposal of the effluents and of the solid waste. The assembly-has been working since 1961. During the 5 to 6 years operation, various improvements have been made and a certain number of observations have been collected concerning the work. (author) [fr

  17. Design requirement on KALIMER control rod assembly duct

    International Nuclear Information System (INIS)

    Hwang, W.; Kang, H. Y.; Nam, C.; Kim, J. O.; Kim, Y. J.

    1998-03-01

    This document establishes the design guidelines which are needs for designing the control rod assembly duct of the KALIMER as design requirements. it describes control rod assembly duct of the KALIMER and its requirements that includes functional requirements, performance requirements, interfacing systems, design limits and strength requirements, seismic requirements, structural requirements, environmental requirements, reliability and safety requirements, standard and codes, QA programs, and other requirements. The control rod system consists of three parts, which are drive mechanism, drive-line, and absorber bundle. This report deals with the absorber bundle and its outer duct only because the others are beyond the scope of fuel system design. The guidelines for design requirements intend to be used for an improved design of the control rod assembly duct of the KALIMER. (author). 19 refs

  18. Design requirement on KALIMER control rod assembly duct

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, W.; Kang, H. Y.; Nam, C.; Kim, J. O.; Kim, Y. J

    1998-03-01

    This document establishes the design guidelines which are needs for designing the control rod assembly duct of the KALIMER as design requirements. it describes control rod assembly duct of the KALIMER and its requirements that includes functional requirements, performance requirements, interfacing systems, design limits and strength requirements, seismic requirements, structural requirements, environmental requirements, reliability and safety requirements, standard and codes, QA programs, and other requirements. The control rod system consists of three parts, which are drive mechanism, drive-line, and absorber bundle. This report deals with the absorber bundle and its outer duct only because the others are beyond the scope of fuel system design. The guidelines for design requirements intend to be used for an improved design of the control rod assembly duct of the KALIMER. (author). 19 refs.

  19. Effect of splitting a mixed-model line on shortening the line length under open- and closed-boundary working area settings

    Science.gov (United States)

    Zhang, Donghao; Matsuura, Haruki; Asada, Akiko

    2017-04-01

    Some automobile factories have segmented mixed-model production lines into shorter sub-lines according to part group, such as engine, trim, and powertrain. The effects of splitting a line into sub-lines have been reported from the standpoints of worker motivation, productivity improvement, and autonomy based on risk spreading. There has been no mention of the possibility of shortening the line length by altering the product sequence using sub-lines. The purpose of the present paper is to determine the conditions under which sub-lines reduce the line length and the degree to which the line length may be shortened. The line lengths for a non-split line and a line that has been split into sub-lines are compared using three methods for determining the working area, the standard closed boundary, the optimized open boundary, and real-life constant-length stations. The results are discussed by analyzing the upper and lower bounds of the line length. Based on these results, a procedure for deciding whether or not to split a production line is proposed.

  20. Courtesy stigma: a hidden health concern among front-line service providers to sex workers.

    Science.gov (United States)

    Phillips, Rachel; Benoit, Cecilia; Hallgrimsdottir, Helga; Vallance, Kate

    2012-06-01

    Courtesy stigma, also referred to as 'stigma by association', involves public disapproval evoked as a consequence of associating with a stigmatised individual or group. While a small number of sociological studies have shown how courtesy stigma limits the social support and social opportunities available to family members of stigmatised individuals, there is a paucity of research examining courtesy stigma among the large network of people who provide health and social services to stigmatised groups. This article presents results from a mixed methods study of the workplace experiences of a purposive sample of workers in a non-profit organisation providing services to sex workers in Canada. The findings demonstrate that courtesy stigma plays a role in workplace health as it shapes both the workplace environment, including the range of resources made available to staff to carry out their work activities, as well as staff perceptions of others' support. At the same time, it was evident that some workers were more vulnerable to courtesy stigma than others depending on their social location. We discuss these results in light of the existing literature on courtesy stigma and conclude that it is an under-studied determinant of workplace health among care providers serving socially denigrated groups. © 2011 The Authors. Sociology of Health & Illness © 2011 Foundation for the Sociology of Health & Illness/Blackwell Publishing Ltd.

  1. Modeling Energy Efficiency As A Green Logistics Component In Vehicle Assembly Line

    Science.gov (United States)

    Oumer, Abduaziz; Mekbib Atnaw, Samson; Kie Cheng, Jack; Singh, Lakveer

    2016-11-01

    This paper uses System Dynamics (SD) simulation to investigate the concept green logistics in terms of energy efficiency in automotive industry. The car manufacturing industry is considered to be one of the highest energy consuming industries. An efficient decision making model is proposed that capture the impacts of strategic decisions on energy consumption and environmental sustainability. The sources of energy considered in this research are electricity and fuel; which are the two main types of energy sources used in a typical vehicle assembly plant. The model depicts the performance measurement for process- specific energy measures of painting, welding, and assembling processes. SD is the chosen simulation method and the main green logistics issues considered are Carbon Dioxide (CO2) emission and energy utilization. The model will assist decision makers acquire an in-depth understanding of relationship between high level planning and low level operation activities on production, environmental impacts and costs associated. The results of the SD model signify the existence of positive trade-offs between green practices of energy efficiency and the reduction of CO2 emission.

  2. Atlas transmission line breakdown analysis

    CERN Document Server

    Nielsen, K E; Ballard, E O; Elizondo, J M; Gribble, R F; McCuistian, B T; Parsons, W M

    1999-01-01

    The Atlas facility will use 24 radially converging, vertically oriented and tapered, oil insulated, triplate transmission lines between the Marx generators and the central load region. Among the requirements of the transmission lines are low inductance and high reliability. The inter-conductor gap is nominally 2 cm and the lines taper from a height of 1.75 m at the Marx end to 0.32 m at the output end. The aluminum conductors, held together by 20 insulating spacers, are assembled and inserted as a unit into radial oil-filled steel tanks. The negative, high-voltage, center conductor is 2.54-cm thick and the outer ground conductors are 1.59-cm thick. All 24 triplate transmission lines connect to a transition section at near 1 m radius that couples the transmission lines to a disk/conical solid- dielectric-insulated power flow channel transmission line terminating at the load. Peak operating voltage on the lines can be as high as 240 kV with an effective stress time of 0.8 mu s. Testing of small sections of the ...

  3. The role of laboratory diagnostic of boreliose in the environment of forest workers

    Directory of Open Access Journals (Sweden)

    Patryk Matuszek

    2013-12-01

    Full Text Available Background: The laboratory diagnostics of boreliose is based on detection of specific IgG and IgM antibodies by ELISA test followed by confirmation test of Line-blot. Material and methods: Testing of the presence of specific anti-Borrelia antibodies was performed in the group of 568 forest workers. The ELISA tests were performed in serum, saliva, and dry spot of blood. The confirmation tests Line blot were performed in serum then the prevalence of particular antibodies against Borrelia was calculated. The ELISA test consists complete extract from Borrelia whereas the Line-blot test consists antigens from B. afzelii, B. burdorferi, and B. garinii. Results: The samples from 201 (35% forest workers have revealed the positive results in ELISA in IgG class and 171 (30 results from this group were confirmed by Line-blot. Only in 40 (7 samples have revealed the positive results in Line-blot but were negative in ELISA tests. The main antigen was VIsE (77% in IgG class. It has been shown that 119 (21% samples have revealed positive results in the IgM class in ELISA tests, and from this group 59 (10% cases were confirmed by Line-blot. Antibody against antigen OspC revealed the highest prevalence (71% in IgM class. The correlation between samples from sera and mucosal transudate have shown r40.736 in the case of IgG and r40.162 in the case of IgM. Conclusion: The frequency, of anti-Borrelia antibodies occurrence was very high and appeared in 42% of forest workers. It has revealed that the correlation of results between serum and mucosal transudate was not satisfactory in the case of ELISA test. In contrary, the correlation of results between serum and dry spot of blood was very high and should be consider as alternative material for boreliose diagnosis.

  4. Nuclear reactor shutdown control rod assembly

    International Nuclear Information System (INIS)

    Bilibin, K.

    1988-01-01

    This patent describes a nuclear reactor having a reactor core and a reactor coolant flowing therethrough, a temperature responsive, self-actuated nuclear reactor shutdown control rod assembly, comprising: an upper drive line terminating at its lower end with a substantially cylindrical wall member having inner and outer surfaces; a lower drive line having a lower end adapted to be attached to a neutron absorber; a ring movable disposed about the outer surface of the wall member of the upper drive line; thermal actuation means adapted to be in heat exchange relationship with coolant in an associated reactor core and in contact with the ring, and balls located within the openings in the upper drive line. When reactor coolant approaches a predetermined design temperature the actuation means moves the ring sufficiently so that the balls move radially out from the recess and into the space formed by the second portion of the ring thereby removing the vertical support for the lower drive line such that the lower drive line moves downwardly and inserts an associated neutron absorber into an associated reactor core resulting in automatic reduction of reactor power

  5. The front line health worker: selection, training, and performance.

    Science.gov (United States)

    Ronaghy, H A; Najarzadeh, E; Schwartz, T A; Russel, S S; Solter, S; Zeighami, B

    1976-03-01

    Iranian villagers with basic literacy were recruited, selected, trained, and deployed as Village Health Workers (VHWs) to rural areas of Iran. VHW clinical visit records and activities logs were analyzed to determine levels and nature of effort achieved in the field. Within six months of deployment, the number of patient visits to VHW treatment services constituted 53% of the target population. Within ten months of deployment, the number of family planning acceptors rose from 8% to 21% of the population at risk. Improvements to water supplies have been effected in 50% of target villages. Sanitary improvements have been made to 35% of the houses and 88% of toilets in those villages. Demographic characteristics, class rank, and place of residence of VHWs appear unassociated with village differences in levels of achievement. However, availability of material resources and actual time spent by VHWs on the job may be factors influencing the differences in outcome between villages.

  6. The protection of migrant workers and international labour standards.

    Science.gov (United States)

    Bohning, W R

    1988-06-01

    mechanism consists basically of a dialogue between the ILO and the Government that is responsible for a law, regulation, or practice alleged to be in contravention of principles it voluntarily accepted. The control machinery is often set in motion by workers' organizations. The UN General Assembly is currently elaborating a new instrument designed to cover both regular and irregular migrant workers and their families.

  7. Balancing a Mixed-Model Assembly System in the Footwear Industry

    OpenAIRE

    Sadeghi , Parisa; Rebelo , Rui ,; Soeiro Ferreira , José

    2017-01-01

    Part 7: Operations Planning, Scheduling and Control; International audience; Portuguese footwear industry has improved dramatically to become one of the main world players. This work is part of a project in cooperation with a large footwear company, operating a new automated assembly equipment, integrating various lines. Balancing such lines implies going from an almost manual preparation executed by experienced operators, to a planning supported by optimisation systems. These complex mixed-m...

  8. Ferritin Assembly in Enterocytes of Drosophila melanogaster

    Directory of Open Access Journals (Sweden)

    Abraham Rosas-Arellano

    2016-02-01

    Full Text Available Ferritins are protein nanocages that accumulate inside their cavity thousands of oxidized iron atoms bound to oxygen and phosphates. Both characteristic types of eukaryotic ferritin subunits are present in secreted ferritins from insects, but here dimers between Ferritin 1 Heavy Chain Homolog (Fer1HCH and Ferritin 2 Light Chain Homolog (Fer2LCH are further stabilized by disulfide-bridge in the 24-subunit complex. We addressed ferritin assembly and iron loading in vivo using novel transgenic strains of Drosophila melanogaster. We concentrated on the intestine, where the ferritin induction process can be controlled experimentally by dietary iron manipulation. We showed that the expression pattern of Fer2LCH-Gal4 lines recapitulated iron-dependent endogenous expression of the ferritin subunits and used these lines to drive expression from UAS-mCherry-Fer2LCH transgenes. We found that the Gal4-mediated induction of mCherry-Fer2LCH subunits was too slow to effectively introduce them into newly formed ferritin complexes. Endogenous Fer2LCH and Fer1HCH assembled and stored excess dietary iron, instead. In contrast, when flies were genetically manipulated to co-express Fer2LCH and mCherry-Fer2LCH simultaneously, both subunits were incorporated with Fer1HCH in iron-loaded ferritin complexes. Our study provides fresh evidence that, in insects, ferritin assembly and iron loading in vivo are tightly regulated.

  9. Health care workers indicate ill preparedness for Ebola Virus Disease outbreak in Ashanti Region of Ghana

    OpenAIRE

    Augustina Angelina Annan; Denis Dekugmen Yar; Michael Owusu; Eno Akua Biney; Paa Kobina Forson; Portia Boakye Okyere; Akosua Adumea Gyimah; Ellis Owusu-Dabo

    2017-01-01

    Abstract Background The recent Ebola Virus Disease (EVD) epidemic that hit some countries in West Africa underscores the need to train front line high-risk health workers on disease prevention skills. Although Ghana did not record (and is yet to) any case, and several health workers have received numerous training schemes, there is no record of any study that assessed preparedness of healthcare workers (HCWS) regarding EVD and any emergency prone disease in Ghana. We therefore conducted a hos...

  10. The Teams from Building 904 celebrated the assembly of the 100th short straight section on 11 April

    CERN Multimedia

    Patrice Loiez

    2005-01-01

    The 100th short straight section for the Large Hadron Collider was assembled at CERN at the beginning of April. These units combine superconducting quadrupoles and other multipole corrector magnets, housed in their cryostats, which are used to guide, focus and fine-tune the beam in the LHC. Building 904, where the 474 short straight sections are being assembled, is often called "Lego Land" by the workers, with a touch of humor and pride because of the wide variety of these sets of magnets and cryostats

  11. Developing a registry of workers involved in nanotechnology: BASF experiences.

    Science.gov (United States)

    David, Raymond M; Nasterlack, Michael; Engel, Stefan; Conner, Patrick R

    2011-06-01

    To assist BASF in the establishment of a registry of workers involved in nanotechnology. The initial step was a complete inventory of nanomaterials and sites of use. Guidance was developed to clarify which particulate nanomaterials were to be included in the survey. Site management was then contacted by the medical department to obtain a list of workers. The time line for collecting data ranged from several months to a year, depending on the information needed, and presented challenges based on the lack of global definition and labeling of nanomaterials. Less than 50 nanomaterials are used as raw materials in less than 10% of the sites globally. In North America, less than 5% of sites and 5% workers use nanomaterials. Further work is required to integrate the inventory, registry, and exposure assessments.

  12. Beyond the Model Worker: Surveying a Creative Precariat

    Directory of Open Access Journals (Sweden)

    Greig de Peuter

    2014-02-01

    Full Text Available The figure of the self-reliant, risk-bearing, non-unionised, self-exploiting, always-on flexibly employed worker in the creative industries has been positioned as a role model of contemporary capitalism. Although the notion of the model-worker is a compelling critical diagnostic of the self-management of precarity in post-Fordist times, I argue that it provides an insufficient perspective on labour and the so-called creative economy to the extent that it occludes the capacity to contest among the workforces it represents. Informed by a larger research project, this article thematises salient features of select collective responses to precarity that are emerging from workers in nonstandard employment in the arts, the media, and cultural industries. The discussion is structured in three main parts: the first, ag-gregation, identifies initiatives in which employment status - rather than a specific profession or sector - is the basis of assembly and advocacy; the second, compensation, highlights unpaid work as a growing point of contention across sectors; and the third, occupation, describes cases in which precarious cultural workers are voicing their grievances and engaging in direct action in the context of wider social movements. These dimensions of the contemporary response to precarisation in the creative industries are at risk of being overlooked if the research optic on workers’ strategies is focused upon a single sector or a particular profession. In conclusion, I emphasise that the organisations, campaigns, and proposals that are surveyed in this article are marked by tensions between and among accommodative adaption, incremental improvements, and radical reformism vis-à-vis precarity.

  13. Directed Self-Assembly of Poly(2-vinylpyridine)-b-polystyrene-b-poly(2-vinylpyridine) Triblock Copolymer with Sub-15 nm Spacing Line Patterns Using a Nanoimprinted Photoresist Template.

    Science.gov (United States)

    Sun, Zhiwei; Chen, Zhenbin; Zhang, Wenxu; Choi, Jaewon; Huang, Caili; Jeong, Gajin; Coughlin, E Bryan; Hsu, Yautzong; Yang, XiaoMin; Lee, Kim Y; Kuo, David S; Xiao, Shuaigang; Russell, Thomas P

    2015-08-05

    Low molecular weight P2VP-b-PS-b-P2VP triblock copolymer (poly(2-vinlypyridine)-block-polystyrene-block-poly(2-vinylpyridine)] is doped with copper chloride and microphase separated into lamellar line patterns with ultrahigh area density. Salt-doped P2VP-b-PS-b-P2VP triblock copolymer is self-assembled on the top of the nanoimprinted photoresist template, and metallic nanowires with long-range ordering are prepared with platinum-salt infiltration and plasma etching. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  14. Electrical Quality Assurance of the Superconducting Circuits during LHC Machine Assembly

    CERN Document Server

    Bozzini, D; Desebe, O; Mess, K H; Russenschuck, Stephan; Bednarek, M; Dworak, D; Górnicki, E; Jurkiewicz, P; Kapusta, P; Kotarba, A; Ludwin, J; Olek, S; Talach, M; Zieblinski, M; Klisch, M; Prochal, B

    2008-01-01

    Based on the LHC powering reference database, all-together 1750 superconducting circuits were connected in the various cryogenic transfer lines of the LHC machine. Testing the continuity, magnet polarity, and the quality of the electrical insulation were the main tasks of the Electrical Quality Assurance (ELQA) activities during the LHC machine assembly. With the assembly of the LHC now complete, the paper reviews the work flow, resources, and the qualification results including the different types of electrical non-conformities.

  15. Variation simulation for compliant sheet metal assemblies with applications

    Science.gov (United States)

    Long, Yufeng

    Sheet metals are widely used in discrete products, such as automobiles, aircraft, furniture and electronics appliances, due to their good manufacturability and low cost. A typical automotive body assembly consists of more than 300 parts welded together in more than 200 assembly fixture stations. Such an assembly system is usually quite complex, and takes a long time to develop. As the automotive customer demands products of increasing quality in a shorter time, engineers in automotive industry turn to computer-aided engineering (CAE) tools for help. Computers are an invaluable resource for engineers, not only to simplify and automate the design process, but also to share design specifications with manufacturing groups so that production systems can be tooled up quickly and efficiently. Therefore, it is beneficial to develop computerized simulation and evaluation tools for development of automotive body assembly systems. It is a well-known fact that assembly architectures (joints, fixtures, and assembly lines) have a profound impact on dimensional quality of compliant sheet metal assemblies. To evaluate sheet metal assembly architectures, a special dimensional analysis tool need be developed for predicting dimensional variation of the assembly. Then, the corresponding systematic tools can be established to help engineers select the assembly architectures. In this dissertation, a unified variation model is developed to predict variation in compliant sheet metal assemblies by considering fixture-induced rigid-body motion, deformation and springback. Based on the unified variation model, variation propagation models in multiple assembly stations with various configurations are established. To evaluate the dimensional capability of assembly architectures, quantitative indices are proposed based on the sensitivity matrix, which are independent of the variation level of the process. Examples are given to demonstrate their applications in selecting robust assembly

  16. Combined effects of ototoxic solvents and noise on hearing in automobile plant workers in Iran.

    Science.gov (United States)

    Mohammadi, Saber; Labbafinejad, Yasser; Attarchi, Mirsaeed

    2010-09-01

    Exposure of workers to mixtures of organic solvents and to occupational noise is frequent in a number of industries. Recent studies suggest that exposure to both can cause a more severe hearing loss than exposure to noise alone. Our cross-sectional study included 411 workers of a large automobile plant divided in three groups. The first group included assembly workers exposed to noise alone; the second included workers in a new paint shop, who were exposed to a mixture of organic solvents at a permissible level; and the third group included paint shop workers exposed to both noise and higher than permissible levels of organic solvents in an old paint shop. These groups were compared in terms of low-frequency hearing loss (model 1; average hearing threshold >25 dB at 0.5 kHz, 1 kHz, and 2 kHz) and high-frequency hearing loss (model 2; average hearing threshold >25 dB at 3 kHz, 4 kHz, 6 kHz, and 8 kHz). High-frequency hearing loss was more common in workers exposed to a combination of noise and mixed organic solvents even at permissible levels than in workers exposed to noise alone even after correction for confounding variables. This study shows that combined exposure to mixed organic solvents and occupational noise can exacerbate hearing loss in workers. Therefore, an appropriate hearing protection programme is recommended, that would include short-interval audiometric examinations and efficient hearing protectors.

  17. AA, sandwich line with magnetic horn

    CERN Multimedia

    CERN PhotoLab

    1980-01-01

    The magnetic horn, focusing the antiprotons emanating from the target, was affixed to a sandwich line through which the 150 kA pulses were supplied. Expecting to have to change from time to time the fragile horn (inner conductor only 0.7 mm thick), the assembly was designed for quick exchange. At the lower end of the sandwich line we see the connectors for the high-current cables, at the upper end the magnet horn. It has just been lifted from the V-supports which held it aligned downstream of the target. Continue with 8010293.

  18. Investigation of Wear Behaviour of Sewn Assemblies of Viscose Linings with Different Treatment

    Directory of Open Access Journals (Sweden)

    Dainora BAČKAUSKAITĖ

    2011-07-01

    Full Text Available Different types of chemical treatment of textile are widely applied in advanced textile. Finishing of textile can provide additional functional properties for products or/and to improve the appearance of final product as well as to improve their mechanical properties. In this research the influence of the industrial treatment of viscose linings on the parameters of fabric surface friction, on fabric surface appearance as well as on the slippage resistance of yarns at a seam was investigated. Raw, dyed, dyed and softened, dyed and non-slip finished plain weaved linings were investigated. The slippage resistance of yarns at a seam in woven fabrics was evaluated according to standard EN ISO 13936-1:2004. The friction was investigated according to the standard DIN 53375 in a fabric-fabric friction pair. Surface of raw, dyed, dyed and softened viscose lining was investigated using SEM. The obtained results have shown that the friction parameters as well as the parameters of seam slippage resistance of dyed or dyed and softened fabrics were higher than the ones of raw fabric. The highest differences in those parameters were obtained for lining that was dyed and treated with non-slip finishing. That type of finishing influenced the break of lining yarns without typical to the other investigated linings slipping near a stitching line.http://dx.doi.org/10.5755/j01.ms.17.2.485

  19. Work-related musculoskeletal disorders (WMDs) risk assessment at core assembly production of electronic components manufacturing company

    Science.gov (United States)

    Yahya, N. M.; Zahid, M. N. O.

    2018-03-01

    This study conducted to assess the work-related musculoskeletal disorders (WMDs) among the workers at core assembly production in an electronic components manufacturing company located in Pekan, Pahang, Malaysia. The study is to identify the WMDs risk factor and risk level. A set of questionnaires survey based on modified Nordic Musculoskeletal Disorder Questionnaires have been distributed to respective workers to acquire the WMDs risk factor identification. Then, postural analysis was conducted in order to measure the respective WMDs risk level. The analysis were based on two ergonomics assessment tools; Rapid Upper Limb Assessment (RULA) and Rapid Entire Body Assessment (REBA). The study found that 30 respondents out of 36 respondents suffered from WMDs especially at shoulder, wrists and lower back. The WMDs risk have been identified from unloading process, pressing process and winding process. In term of the WMDs risk level, REBA and RULA assessment tools have indicated high risk level to unloading and pressing process. Thus, this study had established the WMDs risk factor and risk level of core assembly production in an electronic components manufacturing company at Malaysia environment.

  20. A follow-up comparison of blood lead levels between foreign and native workers of battery manufacturing in Taiwan

    International Nuclear Information System (INIS)

    Chuang, H.-Y.; Cheng, W.-C.; Chen, C.-Y.; Yang, Y.-H.; Sung, F.-C.; Yang, C.-Y.; Wu, T.-N.

    2008-01-01

    Foreign workers employed in industries in Taiwan have been found at elevated risk of injuries. Less well known is whether the elevated risk persists in chemical exposure such as lead exposure at battery manufacturing. A cohort of 70 Thai workers and 55 native workers employed at a battery plant were followed up, after an education of job safety, from 2000 until 2002. This study compared the change of blood lead levels (BLLs) between these two groups of workers. With informed consent, BLLs were measured annually for participants and compared. The average baseline BLLs were approximately at similarly high levels between Thai workers and native workers with means ± standard deviations of 36.9 ± 16.4 and 36.2 ± 12.4 μg/dl, respectively (p = 0.79). At the end of 2002, the average concentration was higher in Thai workers than in native workers. Using mixed models, Thai workers had an average of 5.95 μg/dl increase in BLLs over native workers during the 3-year study. Further measurements revealed that the average BLL for workers in the assembly department was 3.57 ± 1.83 μg/dl in excess, compared with workers in the plate engineering department. Thai workers were more likely to drink alcohol but less likely to wear gloves at work and wash hands before meals. The BLL disparities between Thai workers and native workers can partly be explained by differences in risk-taking behaviors. Higher BLLs in Thai workers suggest the need of language appropriate health education to improve their personal hygiene. Workplace smoking ceasing program may be needed both in Thai and native workers

  1. Work ability score of solvent-exposed workers.

    Science.gov (United States)

    Furu, Heidi; Sainio, Markku; Hyvärinen, Hanna-Kaisa; Kaukiainen, Ari

    2018-03-28

    Occupational chronic solvent encephalopathy (CSE), characterized by neurocognitive dysfunction, often leads to early retirement. However, only the more severe cases are diagnosed with CSE, and little is known about the work ability of solvent-exposed workers in general. The aim was to study memory and concentration symptoms, work ability and the effect of both solvent-related and non-occupational factors on work ability, in an actively working solvent-exposed population. A questionnaire on exposure and health was sent to 3640 workers in four solvent-exposed fields, i.e. painters and floor-layers, boat builders, printers, and metal workers. The total number of responses was 1730. We determined the work ability score (WAS), a single question item of the Work Ability Index, and studied solvent exposure, demographic factors, Euroquest memory and concentration symptoms, chronic diseases, and employment status using univariate and multivariate analyses. The findings were compared to those of a corresponding national blue-collar reference population (n = 221), and a small cohort of workers with CSE (n = 18). The proportion of workers with memory and concentration symptoms was significantly associated with solvent exposure. The WAS of solvent-exposed workers was lower than that of the national blue-collar reference group, and the difference was significant in the oldest age group (those aged over 60). Solvent-exposed worker's WAS were higher than those of workers diagnosed with CSE. The WAS were lowest among painters and floor-layers, followed by metal workers and printers, and highest among boat builders. The strongest explanatory factors for poor work ability were the number of chronic diseases, age and employment status. Solvent exposure was a weak independent risk factor for reduced WAS, comparable to a level of high alcohol consumption. Even if memory and concentration symptoms were associated with higher solvent exposure, the effect of solvents on self

  2. High-resolution Laboratory Measurements of Coronal Lines near the Fe IX Line at 171 Å

    Science.gov (United States)

    Beiersdorfer, Peter; Träbert, Elmar

    2018-02-01

    We present high-resolution laboratory measurements in the spectral region between 165 and 175 Å that focus on the emission from various ions of C, O, F, Ne, S, Ar, Fe, and Ni. This wavelength region is centered on the λ171 Fe IX channel of the Atmospheric Imaging Assembly on the Solar Dynamics Observatory, and we place special emphasis on the weaker emission lines of Fe IX predicted in this region. In general, our measurements show a multitude of weak lines missing in the current databases, where the emission lines of Ni are probably most in need of further identification and reclassification. We also find that the wavelengths of some of the known lines need updating. Using the multi-reference Møller–Plesset method for wavelength predictions and collisional-radiative modeling of the line intensities, we have made tentative assignments of more than a dozen lines to the spectrum of Fe IX, some of which have formerly been identified as Fe VII, Fe XIV, or Fe XVI lines. Several Fe features remain unassigned, although they appear to be either Fe VII or Fe X lines. Further work will be needed to complete and correct the spectral line lists in this wavelength region.

  3. Experiences and Management of Pregnant Radiation Workers at the Pacific Northwest National Laboratory

    International Nuclear Information System (INIS)

    Bliss, Mary; Bowyer, Sonya M.; Bryant, Janet L.; Lipton, Mary S.; Wahl, Karen L.

    2001-01-01

    Radiation workers at the Pacific Northwest National Laboratory are divided into two classes based on whether or not they can encounter radioactive contamination in the normal course of their work. Level I workers primarily handle sealed radioactive materials such as those used to calibrate detectors. Level II workers perform benchtop chemistry. The U.S. Department of Energy has strict guidelines on the management of pregnant radiation workers. Staff members may voluntarily notify their line managers of a pregnancy and be subjected to stringent radiation exposure limits for the developing fetus. The staff member and manager develop a plan to limit and monitor radiation dose for the remainder of the pregnancy. Several examples of dose management plans and case examples of the impact of pregnancy on staff member's technical work and projects will be presented

  4. HEURÍSTICA PARA EL EQUILIBRADO DE LÍNEAS DE ENSAMBLES DEL TIPO TSS HEURISTIC FOR THE TSS ASSEMBLY LINE BALANCING PROBLEM

    Directory of Open Access Journals (Sweden)

    Pedro Palominos Belmar

    2010-12-01

    Full Text Available El propósito de este trabajo es presentar una heurística para el problema de equilibrado de líneas para células conformadas en "U". Particularmente para el sistema de fabricación denominado Toyota Sewing System (TSS, que representa un nuevo concepto de organización en una línea de producción. Si bien este tipo de sistema ha sido abordado en la literatura bajo el título de sistemas de producción autoequilibrado, en donde el equilibrio se logra mediante la utilización de dos reglas básicas, creemos que estas reglas no son suficientes para lograr el autoequilibrio. Por lo cual incorporamos el concepto de zonas de enlace que facilita el equilibrado de la línea. De los resultados obtenidos mediante simulación, concluimos que la heurística es eficiente para este tipo de sistemas de producción.The purpose of this paper is to present a heuristic for the assembly line balancing problem in U-shaped cells, particularly for the manufacturing system called Toyota Sewing System (TSS, which represents a new production line organization concept. Although this type of system has been approached in the literature under the name of self-balanced production system, where the balance is achieved using two basic rules, we believe that these rules are not sufficient to achieve self-balance, so we have incorporated the concept of linkage zones that facilitate balancing the line. From the results obtained by simulation we conclude that the heuristic is efficient for this kind of production system.

  5. Managing bottlenecks in manual automobile assembly systems using discrete event simulation

    Directory of Open Access Journals (Sweden)

    Dewa, M.

    2013-08-01

    Full Text Available Batch model lines are quite handy when the demand for each product is moderate. However, they are characterised by high work-in-progress inventories, lost production time when changing over models, and reduced flexibility when it comes to altering production rates as product demand changes. On the other hand, mixed model lines can offer reduced work-in-progress inventory and increased flexibility. The object of this paper is to illustrate that a manual automobile assembling system can be optimised through managing bottlenecks by ensuring high workstation utilisation, reducing queue lengths before stations and reducing station downtime. A case study from the automobile industry is used for data collection. A model is developed through the use of simulation software. The model is then verified and validated before a detailed bottleneck analysis is conducted. An operational strategy is then proposed for optimal bottleneck management. Although the paper focuses on improving automobile assembly systems in batch mode, the methodology can also be applied in single model manual and automated production lines.

  6. File list: His.Lng.20.AllAg.Lung_adenocarcinoma_cell_lines [Chip-atlas[Archive

    Lifescience Database Archive (English)

    Full Text Available His.Lng.20.AllAg.Lung_adenocarcinoma_cell_lines hg19 Histone Lung Lung adenocarcino...ma cell lines SRX1143596,SRX1143597,SRX1143598,SRX1143599 http://dbarchive.biosciencedbc.jp/kyushu-u/hg19/assembled/His.Lng.20.AllAg.Lung_adenocarcinoma_cell_lines.bed ...

  7. Lung Cancer Mortality among Uranium Gaseous Diffusion Plant Workers: A Cohort Study 1952–2004

    Directory of Open Access Journals (Sweden)

    LW Figgs

    2013-07-01

    Full Text Available Background: 9%–15% of all lung cancers are attributable to occupational exposures. Reports are disparate regarding elevated lung cancer mortality risk among workers employed at uranium gaseous diffusion plants. Objective: To investigate whether external radiation exposure is associated with lung cancer mortality risk among uranium gaseous diffusion workers. Methods: A cohort of 6820 nuclear industry workers employed from 1952 to 2003 at the Paducah uranium gaseous diffusion plant (PGDP was assembled. A job-specific exposure matrix (JEM was used to determine likely toxic metal exposure categories. In addition, radiation film badge dosimeters were used to monitor cumulative external ionizing radiation exposure. International Classification for Disease (ICD codes 9 and 10 were used to identify 147 lung cancer deaths. Logistic and proportional hazards regression were used to estimate lung cancer mortality risk. Results: Lung cancer mortality risk was elevated among workers who experienced external radiation >3.5 mrem and employment duration >12 years. Conclusion: Employees of uranium gaseous diffusion plants carry a higher risk of lung cancer mortality; the mortality is associated with increased radiation exposure and duration of employment.

  8. Assembly of contactors-separators in an extraction unit

    International Nuclear Information System (INIS)

    Beaujard, Jean; Menes, J.-C.; Ravoire, Jean.

    1977-01-01

    A description is given of an assembly of contactors-separators of an installation in which a transfer of mass or an isotope exchange occurs between two non miscible phases, characterized in that the contactors-separators are associated in m lines and n columns, one of the phases issuing from a contactor-separator being sent directly to the next contactor-separator of the same line, whilst the other phase, issuing from the same contactor-separator is sent directly to the next contactor-separator of the same column, each of the m lines and n columns being provided with one only pumping facility, the instantaneous flow rate of each phase, at the intake and outlet of each contactor-separator being appreciably identical [fr

  9. ASSEMBLER program group for preliminary data processing on-line with ES-1010

    International Nuclear Information System (INIS)

    Pshenichnyj, V.A.; Gritsaj, E.A.

    1981-01-01

    The paper deals with programs on the ASSEMBLER language for processing of physical data, obtained in a time-of-flight neutron spectrometer. A program which provides the connection between a measuring room with a computer is given. There are also auxilliary programs for spectra processing recorded on a magnetic disk, spectra plotting and for calculation of areas under peaks for a ν-spectrum ed on a magnetic disk, spectra plotting and for cal

  10. Off-line programming and simulation in handling nuclear components

    International Nuclear Information System (INIS)

    Baker, C.P.

    1993-10-01

    IGRIP was used to create a simulation of the robotic workcell design for handling components at the PANTEX nuclear arms facility. This initial simulation identified problems with the customer's proposed worker layout, and allowed a correction to be proposed. Refinement of the IGRIP simulation allowed the design and construction of a workcell mock-up and accurate off-line programming of the system. IGRIP's off-line programming capabilities are being used to develop the motion control code for the workcell. PNLs success in this area suggests that simulation and off-line programming may be valuable tools for developing robotics in some automation resistant industries

  11. [Lead intoxication in a group of workers in Germany].

    Science.gov (United States)

    Willi, R F; Felgenhauer, N; Eyer, F; Buters, J T; Zilker, T

    2009-12-01

    Seventeen East-European workers with a suspected lead-intoxication presented themselves to the Department of Toxicology. All of them had worked on the renovation of pylons of a high-tension line. The old paint, known to contain lead was removed with needle descalers. The patients had blood lead concentrations between 325 and 1124 microg/l, but no specific symptoms. The workers neglected the protective measures at their working-place. 12 of 17 workers had lead-concentrations above 400 microg/l (Reference lead-concentration above 700 microg/l were treated with the chelating agent meso-2,3-dimercaptosuccinic acid (DMSA) 3 x 200 mg/d for nine days. The patients with lead concentrations between 400 and 700 microg/l were treated which DMSA 3 x 100 mg/d. After the DMSA-treatment the lead-concentrations had dropped (p lead concentration in their blood due to occupational exposure. The high blood lead levels showed that the workers had not been protected adequately. This examplifies that occupational lead exposure still occurs, also in Germany. By patients with unspecific symptoms connected with lead exposure a biomonitoring for lead is necessary.

  12. Fire Resistant Panels for the Tunnel Linings

    Directory of Open Access Journals (Sweden)

    Gravit Marina

    2016-01-01

    Full Text Available Presents the results of studies of innovative materials in the field of experimental and theoretical research fire resistance fireproof panels Pyro-Safe Aestuver T. Owing to the assembly simplicity, materials cheapness, high ecological standard, recycling, reuse potential, are benefit. Research work is running to improve the knowledge about fireproof panels Pyro-Safe Aestuver T for tunnel lining, its basic performance, its long term behavior and in particular also its fire proof for example when used for the lining of road tunnels.

  13. Three-Dimensional Self-Assembled Photonic Crystal Waveguide

    Science.gov (United States)

    Baek, Kang-Hyun

    Photonic crystals (PCs), two- or three-dimensionally periodic, artificial, and dielectric structures, have a specific forbidden band for electromagnetic waves, referred to as photonic bandgap (PBG). The PBG is analogous to the electronic bandgap in natural crystal structures with periodic atomic arrangement. A well-defined and embedded planar, line, or point defect within the PCs causes a break in its structural periodicity, and introduces a state in the PBG for light localization. It offers various applications in integrated optics and photonics including optical filters, sharp bending light guides and very low threshold lasers. Using nanofabrication processes, PCs of the 2-D slab-type and 3-D layer-by-layer structures have been investigated widely. Alternatively, simple and low-cost self-assembled PCs with full 3-D PBG, inverse opals, have been suggested. A template with face centered cubic closed packed structure, opal, may initially be built by self-assembly of colloidal spheres, and is selectively removed after infiltrating high refractive index materials into the interstitials of spheres. In this dissertation, the optical waveguides utilizing the 3-D self-assembled PCs are discussed. The waveguides were fabricated by microfabrication technology. For high-quality colloidal silica spheres and PCs, reliable synthesis, self-assembly, and characterization techniques were developed. Its theoretical and experimental demonstrations are provided and correlated. They suggest that the self-assembled PCs with PBG are feasible for the applications in integrated optics and photonics.

  14. On the front line of primary health care: the profile of community health workers in rural Quechua communities in Peru.

    Science.gov (United States)

    Brown, Angela; Malca, Rosa; Zumaran, Adriana; Miranda, J Jaime

    2006-05-17

    To describe the profile of community health workers--health promoters, traditional birth attendants and traditional healers--in rural Quechua communities from Ayacucho, Peru. Basic quantitative and qualitative information was gathered as part of a community health project implemented between 1997 and 2002 in 40 Andean communities with information from questionnaires, personal interviews and group discussions. The majority of current community health workers are men with limited education who are primarily Quechua speakers undertaking their work on a voluntary basis. Health promoters are mostly young, male, high school graduates. There exists a high drop-out rate among these workers. In contrast, traditional healers and traditional birth attendants possess an almost diametrically opposite profile in terms of age, education and drop-out rates, though males still predominate. At the community level the health promoters are the most visible community health workers. It is very important to consider and to be aware of the profile of community health workers in order to provide appropriate alternatives when working with these groups as well as with the indigenous population, particularly in terms of culture, language and gender issues.

  15. ICC Type II large-format FPA detector assemblies

    Science.gov (United States)

    Clynne, Thomas H.; Powers, Thomas P.

    1997-08-01

    ICC presents a new addition to their integrated detector assembly product line with the announcement of their type II large format staring class FPA units. A result of internally funded research and development, the ICC type II detector assembly can accommodate all existing large format staring class PtSi, InSb and MCT focal planes, up to 640 by 480. Proprietary methodologies completely eliminate all FPA stresses to allow for maximum FPA survivability. Standard optical and cryocooler interfaces allow for the use of BEI, AEG, TI SADA Hughes/Magnavox and Joule Thompson coolers. This unit has been qualified to the current SADA II thermal environmental specifications and was tailored around ICC's worldwide industry standard type IV product. Assembled in a real world flexible manufacturing environment, this unit features a wide degree of adaptability and can be easily modified to a user's specifications via standard options and add-ons that include optical interfaces, electrical interfaces and window/filter material selections.

  16. A 110 m long prototype helium transfer line for the HERA project

    International Nuclear Information System (INIS)

    Horvath, I.; Ming, P.; Von Burg, M.; Horlitz, G.; Sindt, H.

    1986-01-01

    A prototype helium transfer line of 110-m length was designed and constructed at SIN for the HERA project. This rendered a study of the assembly and handling processes as well as the determination of the heat losses into the transfer line. In this paper the transfer line structure is described and first results of heat transfer measurement for the specially developed super-insulation are presented

  17. Calibration of the TVO spent BWR reference fuel assembly

    International Nuclear Information System (INIS)

    Tarvainen, M.; Baecklin, A.; Haakanson, A.

    1992-02-01

    In 1989 the Support Programmes of Finland (FSP) and Sweden (SSP) initiated a joint task to cross calibrate the burnup of the IAEA spent BWR reference fuel assembly at the TVO AFR storage facility (TVO KPA-STORE) in Finland. The reference assembly, kept separately under the IAEA seal, is used for verification measurements of spent fuel by GBUV method (SG-NDA-38). The cross calibration was performed by establishing a calibration curve, 244 Cm neutron rate versus burnup, using passive neutron assay (PNA) measurements. The declared burnup of the reference assembly was compared with the burnup value deduced from the calibration curve. A calibration line was also established by using the GBUV method with the aid of high resolution gamma ray spectrometry (HRGS). Normalization between the two different facilities was performed using sealed neutron and gamma calibration sources. The results of the passive neutron assay show consistency, better than 1 %, between the declared mean burnup of the reference assembly and the burnup deduced from the calibration curve. The corresponding consistency is within +-2 % for the HRGS measurements

  18. Most advanced HTP fuel assembly design for EPR

    International Nuclear Information System (INIS)

    Francillon, Eric; Kiehlmann, Horst-Dieter

    2006-01-01

    End 2003, the Finnish electricity utility Teollisuuden Voima Oy (TVO) signed the contract for building an EPR in Olkiluoto (Finland). Mid 2004, the French electricity utility EDF selected an EPR to be built in France. In 2005, Framatome ANP, an AREVA and Siemens company, announced that they will be pursuing a design certification in the U.S. The EPR development is based on the latest PWR product lines of former Framatome (N4) and Siemens Nuklear (Konvoi). As an introductory part, different aspects of the EPR core characteristics connected to fuel assembly design are presented. It includes means of ensuring reactivity control like hybrid AIC/B4C control rod absorbers and gadolinium as burnable absorber integrated in fuel rods, and specific options for in-core instrumentation, such as Aeroball type instrumentation. Then the design requirements for the EPR fuel assembly are presented in term of very high burnup capacity, rod cladding and fuel assembly reliability. Framatome ANP fuel assembly product characteristics meeting these requirements are then described. EPR fuel assembly design characteristics benefit from the experience feedback of the latest fuel assembly products designed within Framatome ANP, leading to resistance to assembly deformation, high fuel rod restraint and prevention of handling hazards. EPR fuel assembly design features the best components composing the cornerstones of the upgraded family of fuel assemblies that FRAMATOME ANP proposes today. This family is based on a set of common characteristics and associated features, which include the HMP grid as bottom end spacer, the MONOBLOC guide tube and the Robust FUELGUARD as lower tie plate, the use of the M5 Alloy, as cladding and structure material. This fully re-crystallized, ternary Zr-Nb-O alloy produces radically improved in-reactor corrosion, very low hydrogen uptake and growth and an excellent creep behavior, which are described there. EPR fuel assembly description also includes fuel rod

  19. Mobile Applications for Knowledge Workers and Field Workers

    Directory of Open Access Journals (Sweden)

    Stefan Stieglitz

    2015-01-01

    Full Text Available In recent years, the diffusion of mobile applications (mobile apps has risen significantly. Nowadays, mobile business apps are strongly emerging in business, enhancing productivity and employees’ satisfaction, whilst the usage of customized individual enterprise apps is still an exception. Standardized business apps enable basic functionalities, for example, mobile data storage and exchange (e.g., Dropbox, communication (e.g., Skype, and other routine processes, which support mobile workers. In addition, mobile apps can, for example, increase the flexibility of mobile workers by easing the access to firm’s information from outside the enterprise and by enabling ubiquitous collaboration. Hence, mobile apps can generate competitive advantages and can increase work efficiency on a broad scale. But mobile workers form no coherent group. Our research reveals, based on two case studies, that they can be clustered into two groups: knowledge workers and field workers. Knowledge workers and field workers fulfill different tasks and work in different environments. Hence, they have different requirements for mobile support. In this paper we conclude that standardized mobile business apps cannot meet the different requirements of various groups of mobile workers. Task- and firm-specific (individualized requirements determine the specification, implementation, and application of mobile apps.

  20. Three silver linings in the cloud of old age: an autobiographical perspective.

    Science.gov (United States)

    Haber, David

    2014-01-01

    Through the author's experiences as a gerontological social worker, graduate student in gerontology, and gerontology professor, the author discovered not only the cloud of old age, but three silver linings.

  1. Analysis of the Aedes albopictus C6/36 genome provides insight into cell line utility for viral propagation.

    Science.gov (United States)

    Miller, Jason R; Koren, Sergey; Dilley, Kari A; Puri, Vinita; Brown, David M; Harkins, Derek M; Thibaud-Nissen, Françoise; Rosen, Benjamin; Chen, Xiao-Guang; Tu, Zhijian; Sharakhov, Igor V; Sharakhova, Maria V; Sebra, Robert; Stockwell, Timothy B; Bergman, Nicholas H; Sutton, Granger G; Phillippy, Adam M; Piermarini, Peter M; Shabman, Reed S

    2018-03-01

    The 50-year-old Aedes albopictus C6/36 cell line is a resource for the detection, amplification, and analysis of mosquito-borne viruses including Zika, dengue, and chikungunya. The cell line is derived from an unknown number of larvae from an unspecified strain of Aedes albopictus mosquitoes. Toward improved utility of the cell line for research in virus transmission, we present an annotated assembly of the C6/36 genome. The C6/36 genome assembly has the largest contig N50 (3.3 Mbp) of any mosquito assembly, presents the sequences of both haplotypes for most of the diploid genome, reveals independent null mutations in both alleles of the Dicer locus, and indicates a male-specific genome. Gene annotation was computed with publicly available mosquito transcript sequences. Gene expression data from cell line RNA sequence identified enrichment of growth-related pathways and conspicuous deficiency in aquaporins and inward rectifier K+ channels. As a test of utility, RNA sequence data from Zika-infected cells were mapped to the C6/36 genome and transcriptome assemblies. Host subtraction reduced the data set by 89%, enabling faster characterization of nonhost reads. The C6/36 genome sequence and annotation should enable additional uses of the cell line to study arbovirus vector interactions and interventions aimed at restricting the spread of human disease.

  2. The recommendation of line-balancing improvement on MCM product line 1 using genetics algorithm and moodie young at XYZ Company, Co.

    Science.gov (United States)

    Sriwana, I. K.; Marie, I. A.; Mangala, D.

    2017-12-01

    Kencana Gemilang, Co. is one electronics industry engaging in the manufacture sector. This company manufactures and assembles household electronic products, such as rice cooker, fan, iron, blender, etc. The company deals with an issue of underachievement of an established production target on MCM products line 1. This study aimed to calculate line efficiencies, delay times, and initial line smoothness indexes. The research was carried out by means of depicting a precedence diagram and gathering time data of each work element followed by examination and calculation of standard time as well as line balancing using methods of Moodie Young and Generics Algorithm. Based on results of calculation, better line balancing than the existing initial conditions, i.e. improvement in the line efficiency by 18.39%, deterioration in balanced delay by 28.39%, and deterioration of a smoothness index by 23.85% was obtained.

  3. Self assembled linear polymeric chains with tuneable semiflexibility using isotropic interactions

    Science.gov (United States)

    Abraham, Alex; Chatterji, Apratim

    2018-04-01

    We propose a two-body spherically symmetric (isotropic) potential such that particles interacting by the potential self-assemble into linear semiflexible polymeric chains without branching. By suitable control of the potential parameters, we can control the persistence length of the polymer and can even introduce a controlled number of branches. Thus we show how to achieve effective directional interactions starting from spherically symmetric potentials. The self-assembled polymers have an exponential distribution of chain lengths akin to what is observed for worm-like micellar systems. On increasing particle density, the polymeric chains self-organize to an ordered line-hexagonal phase where every chain is surrounded by six parallel chains, the transition is first order. On further increase in monomer density, the order is destroyed and we get a branched gel-like phase. This potential can be used to model semi-flexible equilibrium polymers with tunable semiflexibility and excluded volume. The use of the potential is computationally cheap and hence can be used to simulate and probe equilibrium polymer dynamics with long chains. The potential also gives a plausible method of tuning colloidal interactions in experiments such that one can obtain self-assembling polymeric chains made up of colloids and probe polymer dynamics using an optical microscope. Furthermore, we show how a modified potential leads to the observation of an intermediate nematic phase of self-assembled chains in between the low density disordered phase and the line-ordered hexagonal phase.

  4. A Long-Read Transcriptome Assembly of Cotton (Gossypium hirsutum L. and Intraspecific Single Nucleotide Polymorphism Discovery

    Directory of Open Access Journals (Sweden)

    Hamid Ashrafi

    2015-07-01

    Full Text Available Upland cotton ( L. has a narrow germplasm base, which constrains marker development and hampers intraspecific breeding. A pressing need exists for high-throughput single nucleotide polymorphism (SNP markers that can be readily applied to germplasm in breeding and breeding-related research programs. Despite progress made in developing new sequencing technologies during the past decade, the cost of sequencing remains substantial when one is dealing with numerous samples and large genomes. Several strategies have been proposed to lower the cost of sequencing for multiple genotypes of large-genome species like cotton, such as transcriptome sequencing and reduced-representation DNA sequencing. This paper reports the development of a transcriptome assembly of the inbred line Texas Marker-1 (TM-1, a genetic standard for cotton, its usefulness as a reference for RNA sequencing (RNA-seq-based SNP identification, and the availability of transcriptome sequences of four other cotton cultivars. An assembly of TM-1 was made using Roche 454 transcriptome reads combined with an assembly of all available public expressed sequence tag (EST sequences of TM-1. The TM-1 assembly consists of 72,450 contigs with a total of 70 million bp. Functional predictions of the transcripts were estimated by alignment to selected protein databases. Transcriptome sequences of the five lines, including TM-1, were obtained using an Illumina Genome Analyzer-II, and the short reads were mapped to the TM-1 assembly to discover SNPs among the five lines. We identified >14,000 unfiltered allelic SNPs, of which ∼3,700 SNPs were retained for assay development after applying several rigorous filters. This paper reports availability of the reference transcriptome assembly and shows its utility in developing intraspecific SNP markers in upland cotton.

  5. Life on the line: Job demands, perceived co-worker support for safety, and hazardous work events.

    Science.gov (United States)

    Turner, Nick; Chmiel, Nik; Hershcovis, M Sandy; Walls, Melanie

    2010-10-01

    The present study of 334 United Kingdom trackside workers tested an interaction hypothesis. We hypothesized, drawing on the job demands-resources framework, that perceived support for safety (from senior managers, supervisors, and coworkers) as job resources would weaken the relationship between higher job demands and more frequent hazardous work events. Consistent with social impact theory, we predicted that perceived coworker support for safety would be particularly influential when trackside workers faced higher job demands. Moderated multiple regression showed that, of all three sources of perceived support for safety, perceived coworker support for safety was most important for keeping employees safe in the face of high job demands. © 2010 APA, all rights reserved.

  6. Potential Indoor Worker Exposure From Handling Area Leakage: Example Event Sequence Frequency Analysis

    International Nuclear Information System (INIS)

    Benke, Roland R.; Adams, George R.

    2008-01-01

    The U.S. Department of Energy (DOE) is currently considering design options for the facilities that will handle spent nuclear fuel and high-level radioactive waste at the potential nuclear waste repository at Yucca Mountain, Nevada. The license application must demonstrate compliance with the performance objectives of 10 CFR Part 63, which include occupational dose limits from 10 CFR Part 20. If DOE submits a license application under 10 CFR Part 63, the U.S. Nuclear Regulatory Commission (NRC) will conduct a risk-informed, performance-based review of the DOE license application and its preclosure safety analysis, in which in-depth technical evaluations are focused on technical areas that are significant to preclosure safety and risk. As part of pre-licensing activities, the Center for Nuclear Waste Regulatory Analyses (CNWRA) developed the Preclosure Safety Analysis Tool software to aid in the regulatory review of a DOE license application and support any independent confirmatory assessments that may be needed. Recent DOE information indicates a primarily canister-based handling approach that includes the wet transfer of individual assemblies where Heating, Ventilation, and Air Conditioning (HVAC) systems may be relied on to provide confinement and limit the spread of any airborne radioactive material from handling operations. Workers may be involved in manual and remote operations in handling transportation casks, canisters, waste packages, or bare spent nuclear fuel assemblies inside facility buildings. As part of routine operations within these facilities, radioactive material may potentially become airborne if canisters are opened or bare fuel assemblies are handled. Leakage of contaminated air from the handling area into adjacent occupied areas, therefore, represents a potential radiological exposure pathway for indoor workers. The objective of this paper is to demonstrate modeling capabilities that can be used by the regulator to estimate frequencies of

  7. On the front line of primary health care: the profile of community health workers in rural Quechua communities in Peru

    Directory of Open Access Journals (Sweden)

    Zumaran Adriana

    2006-05-01

    Full Text Available Abstract Objective To describe the profile of community health workers – health promoters, traditional birth attendants and traditional healers – in rural Quechua communities from Ayacucho, Peru. Methods Basic quantitative and qualitative information was gathered as part of a community health project implemented between 1997 and 2002 in 40 Andean communities with information from questionnaires, personal interviews and group discussions. Results The majority of current community health workers are men with limited education who are primarily Quechua speakers undertaking their work on a voluntary basis. Health promoters are mostly young, male, high school graduates. There exists a high drop-out rate among these workers. In contrast, traditional healers and traditional birth attendants possess an almost diametrically opposite profile in terms of age, education and drop-out rates, though males still predominate. At the community level the health promoters are the most visible community health workers. Conclusion It is very important to consider and to be aware of the profile of community health workers in order to provide appropriate alternatives when working with these groups as well as with the indigenous population, particularly in terms of culture, language and gender issues.

  8. Ultra-Precise Assembly of Micro-Electromechanical Systems (MEMS) Components

    Energy Technology Data Exchange (ETDEWEB)

    Feddema, J.T.; Simon, R.; Polosky, M.; Christenson, T.

    1999-04-01

    This report summarizes a three year effort to develop an automated microassembly workcell for the assembly of LIGA (Lithography Galvonoforming Abforming) parts. Over the last several years, Sandia has developed processes for producing surface machined silicon and LIGA parts for use in weapons surety devices. Some of these parts have outside dimensions as small as 100 micron, and most all have submicron tolerances. Parts this small and precise are extremely difficult to assembly by hand. Therefore, in this project, we investigated the technologies required to develop a robotic workcell to assembly these parts. In particular, we concentrated on micro-grippers, visual servoing, micro-assembly planning, and parallel assembly. Three different micro-grippers were tested: a pneumatic probe, a thermally actuated polysilicon tweezer, and a LIGA fabricated tweezer. Visual servoing was used to accuracy position two parts relative to one another. Fourier optics methods were used to generate synthetic microscope images from CAD drawings. These synthetic images are used off-line to test image processing routines under varying magnifications and depths of field. They also provide reference image features which are used to visually servo the part to the desired position. We also investigated a new aspect of fine motion planning for the micro-domain. As parts approach 1-10 {micro}m or less in outside dimensions, interactive forces such as van der Waals and electrostatic forces become major factors which greatly change the assembly sequence and path plans. We developed the mathematics required to determine the goal regions for pick up, holding, and release of a micro-sphere being handled by a rectangular tool. Finally, we implemented and tested the ability to assemble an array of LIGA parts attached to two 3 inch diameter wafers. In this way, hundreds of parts can be assembled in parallel rather than assembling each part individually.

  9. Management of health in the construction and assembly of land pipelines

    Energy Technology Data Exchange (ETDEWEB)

    Richa, Newton M.M.; Ruella, Nildemar C [PETROBRAS, Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The objectives of this study are: describe the main aspects of a health management experience in a work of construction and assembly of land pipeline, highlighting the positive impacts on safety and productivity; demonstrate that the general objective of the health function is to provide technical support to companies, information and services for leaders, managers, supervisors, workers and families in the management of multiple interfaces of health, especially the health-work interface; and demonstrate that the appropriate management of health may contribute significantly to the overall management of undertakings. (author)

  10. Tunable and rapid self-assembly of block copolymers using mixed solvent vapors.

    Science.gov (United States)

    Park, Woon Ik; Tong, Sheng; Liu, Yuzi; Jung, Il Woong; Roelofs, Andreas; Hong, Seungbum

    2014-12-21

    Pattern generation of well-controlled block copolymers (BCPs) with a high Flory-Huggins interaction parameter (χ) is important for applications in sub-20 nm nanolithography. We used mixed solvents of dimethylformamide (DMF) and toluene to control the morphology as well as the time to achieve the targeted morphology via self-assembly of BCPs. By precisely controlling the volume ratio of DMF and toluene, well-ordered line, honeycomb, circular hole, and lamellar nanostructures were obtained from a cylinder-forming poly(styrene-b-2-vinylpyridine) (PS-b-P2VP) BCP with high χ. Furthermore, a well-aligned 12 nm line pattern was successfully achieved in the guiding template within one minute using the mixed solvents. This practical method may also be applicable to self-assembly of other BCPs, providing more opportunities for the next-generation sub-10 nm lithography applications.

  11. The Estonian study of Chernobyl cleanup workers: I. Design and questionnaire data

    International Nuclear Information System (INIS)

    Tekkel, M.; Rahu, M.; Veidebaum, T.

    1997-01-01

    Nearly 2% of the male population of Estonia aged 20-39 years were sent to Chernobyl to assist in the cleanup activities after the reactor accident. A cohort of 4,833 cleanup workers was assembled based on multiple and independent sources of information. Information obtained from 3,704 responses to a detailed questionnaire indicated that 63% of the workers were sent to Chernobyl in 1986; 54% were of Estonian and 35% of Russian ethnicity; 72% were married, and 1,164 of their 5,392 children were conceived after the Chernobyl disaster. The workers were less educated than their counterparts than their counterparts in the general population of Estonia, and only 8.5% had attended university. Based on doses entered in workers records, the mean dose was 11 cGy, with only 1.4% over 25 cGy. Nearly 85% of the workers were sent as part of military training activities, and more than half spent in excess of 3 months in the Chernobyl area. Thirty-six percent of the workers reported having worked within the immediate vicinity of the accident site; 11.5% worked on the roofs near the damaged reactor, clearing the highly radioactive debris. The most commonly performed task was the removal and burial of topsoil (55% of the workers). Potassium iodide was given to over 18% of the men. The study design also incorporates biological indicators of exposure based on the glycophorin A mutational assay of red blood cells and chromosome translocation analyses of lymphocytes; record linkage with national cancer registry and mortality registry files to determine cancer incidence and cause-specific mortality; thyroid screening examinations with ultrasound and fine-needle biopsy; and cryopreserved white blood cells and plasma for future molecular studies. Comprehensive studies of Chernobyl cleanup workers have potential to provide a new information about cancer risks due to protracted exposures to ionizing radiation. 21 refs., 1 fig., 11 tabs

  12. Worker Entrepreneurship.

    Science.gov (United States)

    Doucouliagos, Chris

    1992-01-01

    Evaluates the experience of worker entrepreneurship, highlighting successes and failures in Europe, and analyzes the relative importance of factors to worker entrepreneurship such as access to finance, education and training, organizational culture, and worker risk taking. (JOW)

  13. Catalysts of worker-to-worker violence and incivility in hospitals.

    Science.gov (United States)

    Hamblin, Lydia E; Essenmacher, Lynnette; Upfal, Mark J; Russell, Jim; Luborsky, Mark; Ager, Joel; Arnetz, Judith E

    2015-09-01

    To identify common catalysts of worker-to-worker violence and incivility in hospital settings. Worker-to-worker violence and incivility are prevalent forms of mistreatment in healthcare workplaces. These are forms of counterproductive work behaviour that can lead to negative outcomes for employees, patients and the organisation overall. Identifying the factors that lead to co-worker mistreatment is a critical first step in the development of interventions targeting these behaviours. Retrospective descriptive study. Qualitative content analysis was conducted on the total sample (n = 141) of employee incident reports of worker-to-worker violence and incivility that were documented in 2011 at a large American hospital system. More than 50% of the incidents involved nurses, and the majority of incidents did not involve physical violence. Two primary themes emerged from the analysis: Work Behaviour and Work Organisation. Incidents in the Work Behaviour category were often sparked by unprofessional behaviour, disagreement over responsibilities for work tasks or methods of patient care, and dissatisfaction with a co-worker's performance. Incidents in the Work Organisation category involved conflicts or aggression arising from failure to following protocol, patient assignments, limited resources and high workload. Incidents of worker-to-worker violence and incivility stemmed from dissatisfaction with employee behaviour or from organisational practices or work constraints. These incident descriptions reflect worker dissatisfaction and frustration, resulting from poor communication and collaboration between employees, all of which threaten work productivity. Violence and incivility between hospital employees can contribute to turnover of top performers, hinder effective teamwork and jeopardise the quality of patient care. Identification of common catalysts for worker-to-worker violence and incivility informs the development of mistreatment prevention programmes that can be

  14. Relationship between lighting and noise levels and productivity of the occupants in automotive assembly industry.

    Science.gov (United States)

    Akbari, Jafar; Dehghan, Habibollah; Azmoon, Hiva; Forouharmajd, Farhad

    2013-01-01

    Work environment affects human productivity and his performance. The aims of this study were to investigate the effects of lighting and noise levels on human productivity in the automotive assembly industry. Subjects were 181 workers from different parts of an automobile assembly industry. Illuminance (Lx) at the height of 30 inches from the surface of work station and noise (dBA) were locally measured. Also human productivity by the Goldsmith and Hersey scale (1980) was measured. Data were analyzed by using SPSS v20 Pearson correlation coefficient. The results showed that the relationship between noise level and human productivity is negative and significant (P productivity (P > 0.05). Based on the results, in assembly tasks, noise has a negative impact on human productivity, and lighting does not affect this. So, in order to increase employee productivity, noise control and reduction to less than the standard values (less than 85 dB) is necessary.

  15. Relationship between Lighting and Noise Levels and Productivity of the Occupants in Automotive Assembly Industry

    Directory of Open Access Journals (Sweden)

    Jafar Akbari

    2013-01-01

    Full Text Available Work environment affects human productivity and his performance. The aims of this study were to investigate the effects of lighting and noise levels on human productivity in the automotive assembly industry. Method. Subjects were 181 workers from different parts of an automobile assembly industry. Illuminance (Lx at the height of 30 inches from the surface of work station and noise (dBA were locally measured. Also human productivity by the Goldsmith and Hersey scale (1980 was measured. Data were analyzed by using SPSS v20 Pearson correlation coefficient. Results. The results showed that the relationship between noise level and human productivity is negative and significant (, , but there was no significant relationship between lighting and human productivity (. Conclusion. Based on the results, in assembly tasks, noise has a negative impact on human productivity, and lighting does not affect this. So, in order to increase employee productivity, noise control and reduction to less than the standard values (less than 85 dB is necessary.

  16. Evaluation of the British Columbia AIDS Information Line.

    Science.gov (United States)

    Parsons, D C; Bell, M A; Gilchrist, L D

    1991-01-01

    We evaluated implementation of the British Columbia AIDS Information Line during its initial 15 weeks of operation. Data collected during daily operation of the line included call frequency, caller characteristics, response patterns, caller concerns and community referrals. Information on activities and resources required to implement the AIDS Line was also assembled. The study concluded that the advertising campaign sponsored by the provincial government and other AIDS-related media events had a strong impact on the frequency of calls made to the AIDS Line. However, the effect of both advertising and media events was of relatively short duration, suggesting that utilization of an AIDS information line is dependent on continuing promotional activities. The evaluation results demonstrate the importance of continuous collection of data online utilization, to track public awareness of and response to AIDS-related issues, and to facilitate planning of public education.

  17. SeqLib: a C ++ API for rapid BAM manipulation, sequence alignment and sequence assembly.

    Science.gov (United States)

    Wala, Jeremiah; Beroukhim, Rameen

    2017-03-01

    We present SeqLib, a C ++ API and command line tool that provides a rapid and user-friendly interface to BAM/SAM/CRAM files, global sequence alignment operations and sequence assembly. Four C libraries perform core operations in SeqLib: HTSlib for BAM access, BWA-MEM and BLAT for sequence alignment and Fermi for error correction and sequence assembly. Benchmarking indicates that SeqLib has lower CPU and memory requirements than leading C ++ sequence analysis APIs. We demonstrate an example of how minimal SeqLib code can extract, error-correct and assemble reads from a CRAM file and then align with BWA-MEM. SeqLib also provides additional capabilities, including chromosome-aware interval queries and read plotting. Command line tools are available for performing integrated error correction, micro-assemblies and alignment. SeqLib is available on Linux and OSX for the C ++98 standard and later at github.com/walaj/SeqLib. SeqLib is released under the Apache2 license. Additional capabilities for BLAT alignment are available under the BLAT license. jwala@broadinstitue.org ; rameen@broadinstitute.org. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please e-mail: journals.permissions@oup.com

  18. Mortality of workers in an automobile engine and parts manufacturing complex.

    Science.gov (United States)

    Vena, J E; Sultz, H A; Fiedler, R C; Barnes, R E

    1985-01-01

    A proportionate mortality ratio (PMR) study was conducted using data on workers from three local unions representing an integrated automobile factory composed of forge, foundry, and engine (machine and assembly) plants. Ninety four percent of the death certificates were obtained for all active and non-active workers who died during the period 1 January 1970 to 31 December 1979 and were vested in union and company benefit programmes. Observed numbers of deaths were compared with expected numbers based on two standards, the proportionate mortality among men in the United States 1970-9 and among men in Erie County 1975. There was close agreement between the number of observed and expected deaths by either standard of comparison among white auto workers in the forge and foundry plants. Valid analyses of cause specific mortality among non-whites could be conducted for the foundry plant only. Although there was raised PMR for deaths due to diseases of the circulatory system using the Erie County standard, none of the other cause specific PMRs was significant. Although based on small numbers, the risk of cancer of the lung was significantly high in non-whites under age 50 in the foundry (PMR = 2.6; p less than 0.05). The cause specific PMRs for whites in the engine plant were statistically significant for malignant neoplasms (1.2) and all external causes (0.62) based on the US white male standard. Analysis of cancer specific mortality among white men in the machining/assembly plant showed significant excesses for cancer of the digestive system (PMR=1.5), particularly of the liver (PMR=2.6) and pancreas (PMR=1.9); cancers of the respiratory system (PMR=1.4 using the Erie County standard); and cancer of the urinary bladder (PMR=2.3). Workers employed for more than 20 years showed statistically increased mortality ratios for cancers of the digestive system (1.9), particularly cancer of the pancreas (2.3) and cancer of the rectum (2.8). Individuals whose employment began

  19. Incomplete Faraday cage effect of helicopters used in platform live-line maintenance

    Energy Technology Data Exchange (ETDEWEB)

    Cameron, G.W.; Bodger, P.S.; Woudberg, J.J. [University of Canterbury, Christchurch (New Zealand). Dept. of Electrical and Electronic Engineering

    1998-03-01

    The use of helicopters for maintenance on live overhead transmission lines has become a realistic option. The helicopter blades, body and working platform can be seen as creating an incomplete Faraday cage which may be an enhancement to live-line worker safety. This paper simulates the condition using a Faraday cage which can be dismantled in a controlled laboratory environment, to ascertain the effectiveness of apparatus. (author)

  20. Unskilled blue collar workers: Bourgeois and/or authoritarian? Results from a small scale survey in Belgium

    Directory of Open Access Journals (Sweden)

    Hans De Witte

    2007-04-01

    adopted the attitudes (and life style of white collar workers, from whom they can no longer be distinguished. Lipset’s hypothesis of the ‘authoritarianism of the working class’, on the other hand, states that blue collar workers more strongly endorse a conservative attitude on socio-cultural matters and a progressive stand concerning socio-economic issues. Both hypotheses are tested using data from a small scale survey (N = 135 among unskilled blue collar workers and lower- and mid-level white collar workers from different large companies in the region of Leuven, Belgium. The results indicate that the interviewed unskilled blue collar workers still hold a set of attitudes that distinguishes them from the interviewed white collar workers. So, the ‘embourgeoisement’ thesis was refuted. Instead, the unskilled blue collar workers were more conservative on a socio-cultural level, and more progressive concerning socio-economic issues. These results are in line with Lipset’s ‘authoritarianism of the working class’ hypothesis.

  1. The genomic sequence of the Chinese hamster ovary (CHO)-K1 cell line

    DEFF Research Database (Denmark)

    Xu, Xun; Pan, Shengkai; Liu, Xin

    2011-01-01

    Chinese hamster ovary (CHO)-derived cell lines are the preferred host cells for the production of therapeutic proteins. Here we present a draft genomic sequence of the CHO-K1 ancestral cell line. The assembly comprises 2.45 Gb of genomic sequence, with 24,383 predicted genes. We associate most of...

  2. The Social Workers Challenges on Community Welfare in Ungogo Community, Nigeria

    Directory of Open Access Journals (Sweden)

    Kehinde Adekunle Aliyu

    2017-10-01

    Full Text Available The role of social workers in a community cannot be overemphasised by any mean, for the life span of any community depends on the quality of the social workers. The aim of this work is to affirm the roles of social workers in helping the community welfare.  Qualitative research design was adopted for the work. Data collected with the Interview Schedule for Officials of the Federal Road Safety Corps and Interview Guide for selected group of people. This was administered to 30 respondents, which comprises both male and female in the Ungogo community. The purpose of the study was to examine the roles of social workers, in line with improved standards of living, sustained economic development and expansion of trade and economic relations in the community; enhanced levels of international competitiveness in the areas of community welfare, organization for increased productivity of people in the community. It common knowledge every individual strife to be the best when receive the necessary or adequate encouragement. To these extents, such a person bears some responsibilities even if passively so as a member. The implication of this work is to contribute to social change by informing social worker on their challenges and responsibilities ahead of them in the community.

  3. EPA's proposed Worker Protection Standard and the burdens of the past.

    Science.gov (United States)

    Bohme, Susanna Rankin

    2015-01-01

    An Environmental Protection Agency (EPA) recommendation for extensive changes to the Agency's 40-year-old Worker Protection Standard is currently stalled in the "proposed rule" stage. The proposal, which was available for public comment until 18 August, would improve safety, training, and hazard communication policies for agricultural pesticides. Exposure to hazards, including high heat, heavy machinery, stoop labor, and pesticides, makes occupational illness uncommonly common among the USA's estimated 2.5 million farm workers. To consider the proposed revisions' likelihood of addressing historical gaps in farmworker protection. The proposal was compared to the existing Worker Protection Standard, and key aspects were analyzed in relation to existing science on farm labor hazards, as well as historic occupational health, labor and immigration policy. US law historically has left farm workers largely unprotected. These exclusions and delays have been tolerated in part thanks to the myth of the independent family farmer, but more significant is the stingy nativism that presumes to benefit from immigrant labor without assuming any responsibility to protect the humans who provide it. In the first half of the 1970s, workers lobbied for robust protections, but rule making was impeded by lack of data and by the disproportionate influence of agricultural employers who sought minimal regulation. In 1974, the EPA passed the first Worker Protection Standard for farm workers. Key aspects of the proposed revision include stronger protections against drift and re-entry exposures, better information provision and training, and increased protections for workers under 16 years. The proposed changes represent an improvement over existing legislation, but do not go far enough. The revision should be strengthened along lines suggested by farm workers themselves, and other labor laws must also be amended to give the men, women, and children who work in the fields of this country full

  4. Chromosome aberrations in workers with exposure to α-particle radiation from internal deposits of plutonium: expectations from in vitro studies and comparisons with workers with predominantly external γ-radiation exposure

    Energy Technology Data Exchange (ETDEWEB)

    Curwen, Gillian B.; Tawn, E.J. [The University of Manchester, Centre for Integrated Genomic Medical Research (CIGMR), School of Population Health, Faculty of Medical and Human Sciences, Manchester (United Kingdom); Sotnik, Natalia V.; Azizova, Tamara V. [Southern Urals Biophysics Institute (SUBI), Ozyorsk, Chelyabinsk Region 456780 (Russian Federation); Cadwell, Kevin K. [Medical School, Newcastle University, Institute for Cell and Molecular Biosciences, Newcastle upon Tyne (United Kingdom); Hill, Mark A. [University of Oxford, CRUK/MRC Oxford Institute for Radiation Oncology, Gray Laboratories, Oxford (United Kingdom)

    2015-05-15

    mFISH analysis of chromosome aberration profiles of 47 and 144 h lymphocyte cultures following exposure to 193 mGy α-particle radiation confirmed that the frequency of stable aberrant cells and stable cells carrying translocations remains constant through repeated cell divisions. Age-specific rates and in vitro dose-response curves were used to derive expected translocation yields in nine workers from the Mayak nuclear facility in Russia. Five had external exposure to γ-radiation, two of whom also had exposure to neutrons, and four had external exposure to γ-radiation and internal exposure to α-particle radiation from incorporated plutonium. Doubts over the appropriateness of the dose response used to estimate translocations from the neutron component made interpretation difficult in two of the workers with external exposure, but the other three had translocation yields broadly in line with expectations. Three of the four plutonium workers had translocation yields in line with expectations, thus supporting the application of the recently derived in vitro α-particle dose response for translocations in stable cells. Overall this report demonstrates that with adequate reference in vitro dose-response curves, translocation yield has the potential to be a useful tool in the validation of red bone marrow doses resulting from mixed exposure to external and internal radiation. (orig.)

  5. The Impact of Job Characteristics on Burnout Among Chinese Correctional Workers.

    Science.gov (United States)

    Jin, Xiaohong; Sun, Ivan Y; Jiang, Shanhe; Wang, Yongchun; Wen, Shufang

    2018-02-01

    Job burnout has long been recognized as a common occupational hazard among correctional workers. Although past studies have investigated the effects of job-related characteristics on correctional staff burnout in Western societies, this line of research has largely been absent from the literature on community corrections in China. Using data collected from 225 community correction workers in a Chinese province, this study assessed the effects of positive and negative job characteristics on occupational burnout. Positive job characteristics included job autonomy, procedural justice, and role clarity. Negative characteristics included role conflict, job stress, and job dangerousness. As expected, role clarity tended to reduce burnout, whereas role conflict, job stress, and job dangerousness were likely to produce greater burnout among Chinese community correction workers. Male correctional officers were also subjected to a higher level of burnout than their female coworkers. Implications for future research and policy were discussed.

  6. PWR and BWR spent fuel assembly gamma spectra measurements

    Energy Technology Data Exchange (ETDEWEB)

    Vaccaro, S. [European Commission, DG Energy, Directorate EURATOM Safeguards Luxembourg (Luxembourg); Tobin, S.J.; Favalli, A. [Los Alamos National Laboratory, Los Alamos, NM (United States); Grogan, B. [Oak Ridge National Laboratory, Oak Ridge (United States); Jansson, P. [Uppsala University, Uppsala (Sweden); Liljenfeldt, H. [Oak Ridge National Laboratory, Oak Ridge (United States); Mozin, V. [Lawrence Livermore National Laboratory, Livermore, CA (United States); Hu, J. [Oak Ridge National Laboratory, Oak Ridge (United States); Schwalbach, P. [European Commission, DG Energy, Directorate EURATOM Safeguards Luxembourg (Luxembourg); Sjöland, A. [Swedish Nuclear Fuel and Waste Management Company (SKB) (Sweden); Trellue, H.; Vo, D. [Los Alamos National Laboratory, Los Alamos, NM (United States)

    2016-10-11

    A project to research the application of nondestructive assay (NDA) to spent fuel assemblies is underway. The research team comprises the European Atomic Energy Community (EURATOM), embodied by the European Commission, DG Energy, Directorate EURATOM Safeguards; the Swedish Nuclear Fuel and Waste Management Company (SKB); two universities; and several United States national laboratories. The Next Generation of Safeguards Initiative–Spent Fuel project team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. This study focuses on spectrally resolved gamma-ray measurements performed on a diverse set of 50 assemblies [25 pressurized water reactor (PWR) assemblies and 25 boiling water reactor (BWR) assemblies]; these same 50 assemblies will be measured with neutron-based NDA instruments and a full-length calorimeter. Given that encapsulation/repository and dry storage safeguards are the primarily intended applications, the analysis focused on the dominant gamma-ray lines of {sup 137}Cs, {sup 154}Eu, and {sup 134}Cs because these isotopes will be the primary gamma-ray emitters during the time frames of interest to these applications. This study addresses the impact on the measured passive gamma-ray signals due to the following factors: burnup, initial enrichment, cooling time, assembly type (eight different PWR and six different BWR fuel designs), presence of gadolinium rods, and anomalies in operating history. To compare the measured results with theory, a limited number of ORIGEN-ARP simulations were performed.

  7. Maternal health phone line: saving women in papua new Guinea.

    Science.gov (United States)

    Watson, Amanda H A; Sabumei, Gaius; Mola, Glen; Iedema, Rick

    2015-04-27

    This paper presents the findings of a research project which has involved the establishment of a maternal health phone line in Milne Bay Province of Papua New Guinea (PNG). Mobile phones and landline phones are key information and communication technologies (ICTs). This research study uses the "ICTs for healthcare development" model to ascertain benefits and barriers to the successful implementation of the Childbirth Emergency Phone. PNG has a very high maternal mortality rate. The "three stages of delay" typology was developed by Thaddeus and Maine to determine factors that might delay provision of appropriate medical treatment and hence increase risk of maternal death. The "three stages of delay" typology has been utilised in various developing countries and also in the present study. Research undertaken has involved semi-structured interviews with health workers, both in rural settings and in the labour ward in Alotau. Additional data has been gathered through focus groups with health workers, analysis of notes made during phone calls, interviews with women and community leaders, observations and field visits. One hundred percent of interviewees (n = 42) said the project helped to solve communication barriers between rural health workers and Alotau Provincial Hospital. Specific examples in which the phone line has helped to create positive health outcomes will be outlined in the paper, drawn from research interviews. The Childbirth Emergency Phone project has shown itself to play a critical role in enabling healthcare workers to address life-threatening childbirth complications. The project shows potential for rollout across PNG; potentially reducing maternal morbidity and maternal mortality rates by overcoming communication challenges.

  8. Robotically Assembled Aerospace Structures: Digital Material Assembly using a Gantry-Type Assembler

    Science.gov (United States)

    Trinh, Greenfield; Copplestone, Grace; O'Connor, Molly; Hu, Steven; Nowak, Sebastian; Cheung, Kenneth; Jenett, Benjamin; Cellucci, Daniel

    2017-01-01

    This paper evaluates the development of automated assembly techniques for discrete lattice structures using a multi-axis gantry type CNC machine. These lattices are made of discrete components called "digital materials." We present the development of a specialized end effector that works in conjunction with the CNC machine to assemble these lattices. With this configuration we are able to place voxels at a rate of 1.5 per minute. The scalability of digital material structures due to the incremental modular assembly is one of its key traits and an important metric of interest. We investigate the build times of a 5x5 beam structure on the scale of 1 meter (325 parts), 10 meters (3,250 parts), and 30 meters (9,750 parts). Utilizing the current configuration with a single end effector, performing serial assembly with a globally fixed feed station at the edge of the build volume, the build time increases according to a scaling law of n4, where n is the build scale. Build times can be reduced significantly by integrating feed systems into the gantry itself, resulting in a scaling law of n3. A completely serial assembly process will encounter time limitations as build scale increases. Automated assembly for digital materials can assemble high performance structures from discrete parts, and techniques such as built in feed systems, parallelization, and optimization of the fastening process will yield much higher throughput.

  9. [Inter-rater agreement on self-reported exposure to ergonomic risk factors for the upper extremities among mechanic assemblers in an automotive industry].

    Science.gov (United States)

    d'Errico, Angelo; Fontana, Dario; Merogno, Angela

    2016-01-01

    to assess reproducibility of self-reported exposure to ergonomic hazards for the upper limbs, measured through a questionnaire based on a diffused checklist for the assessment of ergonomic risk (OCRA) in a sample of mechanical assemblers of an automotive industry. cross-sectional study; reproducibility was assessed as interrater agreement of a composite index of ergonomic risk, estimated through the intraclass correlation coefficient (ICC). 58 mechanical assemblers, working in 29 twin areas, characterised by same work stations and tasks. composite index of ergonomic risk for the upper limbs. reproducibility of the ergonomic index was high in the overall sample (ICC: 0.81) and it was higher for the twin areas employing same-gender workers (ICC: 0.96), compared to those with workers of the opposite gender (ICC: 0.66). these results indicate that a questionnaire measuring with a great detail the exposure to the main ergonomic risk factors for the upper limbs, as the one based on the OCRA checklist used for this study, would allow to obtain a highly reproducible ergonomic index. If its validity against the corresponding observational checklist will be found elevated by future studies, this questionnaire may represent a useful tool for a preliminary assessment of workers' exposure to ergonomic hazards for the upper limbs.

  10. [The occupational physician and communication to workers].

    Science.gov (United States)

    Perbellini, L; di Leo, E; Goio, I

    2010-01-01

    Communication ability is essential for the Physician to the proper management of ambulatory activity and corporate training. The aim of this work is describe the communication strategies to be adopted in everyday healthcare practice. When the occupational physician relates with an employee his message must act both verbal both non-verbal. The medical history should be collected carefully and during the physical examination is important to put the employee at ease by adopting a discreet and attentive attitude. The clinical findings and the capacity to work with any limitations will be discussed at the end of health surveillance using understandable terminology to the worker. During the training-information process is important to define the primary objectives, organize the program and bring the display materials. The worker should be actively involved and encouraged to learn throughout the course information. In the text will also be shown the main aspects of information on line.

  11. Fuel assembly

    International Nuclear Information System (INIS)

    Ueda, Makoto; Ogiya, Shunsuke.

    1989-01-01

    For improving the economy of a BWR type reactor by making the operation cycle longer, the fuel enrichment degree has to be increased further. However, this makes the subcriticality shallower in the upper portion of the reactor core, to bring about a possibility that the reactor shutdown becomes impossible. In the present invention, a portion of fuel rod is constituted as partial length fuel rods (P-fuel rods) in which the entire stack length in the effective portion is made shorter by reducing the concentration of fissionable materials in the axial portion. A plurality of moderator rods are disposed at least on one diagonal line of a fuel assembly and P-fuel rods are arranged at a position put between the moderator rods. This makes it possible to reactor shutdown and makes the axial power distribution satisfactory even if the fuel enrichment degree is increased. (T.M.)

  12. Sequence assembly

    DEFF Research Database (Denmark)

    Scheibye-Alsing, Karsten; Hoffmann, S.; Frankel, Annett Maria

    2009-01-01

    Despite the rapidly increasing number of sequenced and re-sequenced genomes, many issues regarding the computational assembly of large-scale sequencing data have remain unresolved. Computational assembly is crucial in large genome projects as well for the evolving high-throughput technologies and...... in genomic DNA, highly expressed genes and alternative transcripts in EST sequences. We summarize existing comparisons of different assemblers and provide a detailed descriptions and directions for download of assembly programs at: http://genome.ku.dk/resources/assembly/methods.html....

  13. Recent progress in the development of CsI(Tl) crystal-Si-photodiode spectrometric detection assemblies

    International Nuclear Information System (INIS)

    Semynozhenko, V.P.; Grinyov, B.V.; Nekrasov, V.V.; Borodenko, Yu.A.

    2005-01-01

    Highly sensitive spectrometric γ-detection assemblies are developed using a comprehensive approach (optimization of crystal growth conditions as well as of treatment and packing of scintillators, creation of low-noise charge-sensitive preamplifiers and shapers). The detection assemblies with CsI(Tl)≤100 cm 3 have a sensitivity of about 20 pulse/s(mcR/h), their energy resolution with respect to 137 Cs γ-line being ≤8.5%. The assemblies with lesser scintillator volumes (1-5 cm 3 ) provide a resolution lower than 6% with respect to 137 Cs and ≤40% with respect to 241 Am

  14. Who strategies and action to protect and promote the health of workers

    Directory of Open Access Journals (Sweden)

    Ivan Dimov Ivanov

    2007-12-01

    Full Text Available WHO's action on protecting and promoting the health of workers is mandated by the Constitution of the Organization and a number of resolutions of the World Health Assembly. Recognizing that occupational health is closely linked to public health and health systems development, WHO is addressing all determinants of workers' health, including risks for disease and injury in the occupational environment, social and individual factors, and access to health services. Furthermore, the workplace is being used as a setting for protecting and promoting the health of workers and their families. Concerned that despite the existence of effective interventions to prevent occupational diseases and injuries there are still major gaps in the health status of workers between and within countries, the 60th World Health Assembly in 2007 endorsed the Global Plan of Action on Workers' Health. This Plan provides a political framework for development of policies, infrastructure, technologies and partnerships for achieving a basic level of health protection in all workplaces throughout the world. The Health Assembly also urged the 193 Member States of WHO to develop national plans and strategies for implementing the Global Plan of Action and to work towards full coverage of all workers with essential interventions and basic services for prevention of occupational diseases and injuries. A large network of 65 collaborating centres provides support to WHO's action on workers' health. The priorities for global action in the coming ten years include policy instruments on workers' health, workplace health protection and promotion, occupational health services, evidence for action and practice, and workers' health in other policies. Thus, WHO action on workers' health contributes to the global health agenda with regards to health security, climate change and Millenium Development Goals.Las acciones de protección y promoción de la salud de los trabajadores se corresponde con

  15. Workers of Acromyrmex echinatior leafcutter ants police worker-laid eggs, but not reproductive workers

    DEFF Research Database (Denmark)

    Dijkstra, Michiel B.; van Zweden, Jelle Stijn; Dirchsen, Maria

    2010-01-01

    Nonreproductive workers of many eusocial Hymenoptera 'police' the colony, that is, they attack reproductive sister workers or destroy their eggs (unfertilized; developing into haploid males). Several ultimate causes of policing have been proposed, including (1) an increase in colony productivity,...... reproductive workers. We infer that relatedness incentives are the most likely ultimate cause of the evolutionary maintenance of worker-egg policing in A. echinatior. (C) 2010 The Association for the Study of Animal Behaviour. Published by Elsevier Ltd. All rights reserved...

  16. GABenchToB: a genome assembly benchmark tuned on bacteria and benchtop sequencers.

    Directory of Open Access Journals (Sweden)

    Sebastian Jünemann

    Full Text Available De novo genome assembly is the process of reconstructing a complete genomic sequence from countless small sequencing reads. Due to the complexity of this task, numerous genome assemblers have been developed to cope with different requirements and the different kinds of data provided by sequencers within the fast evolving field of next-generation sequencing technologies. In particular, the recently introduced generation of benchtop sequencers, like Illumina's MiSeq and Ion Torrent's Personal Genome Machine (PGM, popularized the easy, fast, and cheap sequencing of bacterial organisms to a broad range of academic and clinical institutions. With a strong pragmatic focus, here, we give a novel insight into the line of assembly evaluation surveys as we benchmark popular de novo genome assemblers based on bacterial data generated by benchtop sequencers. Therefore, single-library assemblies were generated, assembled, and compared to each other by metrics describing assembly contiguity and accuracy, and also by practice-oriented criteria as for instance computing time. In addition, we extensively analyzed the effect of the depth of coverage on the genome assemblies within reasonable ranges and the k-mer optimization problem of de Bruijn Graph assemblers. Our results show that, although both MiSeq and PGM allow for good genome assemblies, they require different approaches. They not only pair with different assembler types, but also affect assemblies differently regarding the depth of coverage where oversampling can become problematic. Assemblies vary greatly with respect to contiguity and accuracy but also by the requirement on the computing power. Consequently, no assembler can be rated best for all preconditions. Instead, the given kind of data, the demands on assembly quality, and the available computing infrastructure determines which assembler suits best. The data sets, scripts and all additional information needed to replicate our results are freely

  17. Bacteriophage Assembly

    Directory of Open Access Journals (Sweden)

    Anastasia A. Aksyuk

    2011-02-01

    Full Text Available Bacteriophages have been a model system to study assembly processes for over half a century. Formation of infectious phage particles involves specific protein-protein and protein-nucleic acid interactions, as well as large conformational changes of assembly precursors. The sequence and molecular mechanisms of phage assembly have been elucidated by a variety of methods. Differences and similarities of assembly processes in several different groups of bacteriophages are discussed in this review. The general principles of phage assembly are applicable to many macromolecular complexes.

  18. A replacement LH2 recirculation line before installation in Discovery

    Science.gov (United States)

    1999-01-01

    A spare four-inch diameter LH2 recirculation line (shown in photo) will be used to replace a damaged LH2 line in the orbiter Discovery. The line recirculates hydrogen from the Shuttle main engines back to the external tank during prelaunch engine conditioning. Workers noted a dent in the line during routine aft compartment inspections Tuesday, Dec. 7. The dent measures 12 inches long and about =-inch deep. Managers expect the replacement work to take about 3 days, followed by system retests and final aft compartment close-outs. Preliminary assessments reflect a launch date of Space Shuttle Discovery on mission STS-103 no earlier than Dec. 16. STS-103 is the third servicing mission for the Hubble Space Telescope.

  19. Investigating the Effects of Concurrent Performance of Physical and Cognitive Demanding Task in Paced Assembly Lines

    Directory of Open Access Journals (Sweden)

    Shakil Ahmed Shaikh

    2013-07-01

    Full Text Available The study was undertaken to investigate the effects of pacing on aspects of performance at an assembly task and on the operators' responses related to work behaviour, perceived workload and perceived stress. A particular objective of the study was to investigate whether physical and cognitive demands may interact in their influences on these effects. An assembly task was simulated in the laboratory and the level of pacing imposed, work height and memory load within the task were all varied. The results showed that the type of pacing commonly imposed (as is common with a lean manufacturing Takt time system in industry can significantly affect both performance and perceived workload and stress. Physical demands (through work height affecting posture and mental demand (through memory load were also found to have significant effects, as would be expected from the many studies of these in the literature. More importantly, some interactions were found between pacing and work height in their effects on quality of assembly and the operator's own rating of performance, and between work height and memory load in their effects on errors. These findings will need to be taken into account by companies when implementing Takt time systems.

  20. A participatory and integrative approach to improve productivity and ergonomics in assembly

    NARCIS (Netherlands)

    Looze, M.P. de; Rhijn, J.W. van; Deursen, J. van; Tuinzaad, G.H.; Reijneveld, C.N.

    2003-01-01

    A participatory and integrative approach was applied to improve the productivity and ergonomics of the assembly lines in two factories, producing magnetic stop valves and office furniture, respectively. Main elements of the approach are the active participation of the company and the integration of

  1. "Controlling ourselves, by ourselves": risk assemblages on Malaysia's assembly lines.

    Science.gov (United States)

    Root, Robin

    2008-01-01

    Since the early 1990s, the Malaysian government has identified factories as high risk for HIV and AIDS. Signaling epidemiological concerns over the rising rates of HIV among factory workers, a significant proportion of whom are women, the label also appeared to reconstitute stereotypes of factory women as dangerously sexual and of factories as immoral spaces. Drawing on ethnographic research in the export processing zones of Penang, Malaysia in the mid-1990s, I examine the meanings and experiences of HIV risk among factory women themselves. Data were analyzed using discourse and grounded theory methods, the former to identify women's multiple modes of rationalizing HIV risks, and the latter to theorize the sources and significance of women's HIV risk assemblages. The heuristic of assemblages as localized knowledge spaces helped to show that biomedical and socioreligious risk lexica operated not as fixed epistemological categories but as situational resources in women's risk scripts. Overall, women desired multiple risk knowledges to help them "control themselves by themselves," a project of reflexive self-shaping mediated by the diverse and discordant discourses of gender, ethnicity, and modernity in Malaysia that shaped how HIV risks were engendered and experienced.

  2. On-line liquid-effluent monitoring of sewage at Lawrence Livermore National Laboratory

    International Nuclear Information System (INIS)

    Dreicer, M.; Cate, J.L.; Rueppel, D.W.; Huntzinger, C.J.; Gonzalez, M.A.

    1982-01-01

    An automatic on line sewage effluent monitoring system has been developed. A representative fraction of the total waste stream leaving the site is monitored for pH, radiation, and metals as it passes through a detection assembly. This assembly consists of an industrial pH probe, NaI radiation detectors, and an x-ray fluorescence metal detector. A microprocessor collects, reduces and analyzes the data to determine if the levels are acceptable by established environmental limits. Currently, if preset levels are exceeded, a sample of the suspect sewage is automatically collected for further analysis, and an alarm is sent to a station where personnel can be alerted to respond on a 24-hour basis. Since at least four hours pass before LLNL effluent reaches the treatment plant, sufficient time is available to alert emergency personnel, evaluate the situation, and if necessary arrange for diversion of the material to emergency holding basins at the treatment plant. Information on the current system is presented, and progress is reported in developing an on-line tritium monitor as an addition to the assembly

  3. Measuring the sensitivity of a boron-lined ion chamber

    International Nuclear Information System (INIS)

    Barton, D.M.

    1992-03-01

    Boron-lined ion chambers are used to monitor external neutron flux from fissionable materials assembled at the Los Alamos Critical Assembly Experiment Facility. The sensitivity of these chambers must be measured periodically in order to detect changes in filling gas and to evaluate other factors that may affect chamber performance. We delineate a procedure to measure ion chamber response using a particular neutron source ( 239 PuBe) in a particular moderating geometry of polyethylene. We also discuss use of the amplifier, high-voltage power supply, recorders, and scram circuits that comprise the complete ion chamber monitoring system

  4. Strengthening practical wisdom: mental health workers' learning and development.

    Science.gov (United States)

    Eriksen, Kristin Ådnøy; Dahl, Hellen; Karlsson, Bengt; Arman, Maria

    2014-09-01

    Practical wisdom, understood as knowing how to be or act in any present situation with clients, is believed to be an essential part of the knowledge needed to be a professional mental health worker. Exploring processes of adapting, extending knowledge and refining tacit knowledge grounded in mental health workers' experiences with being in practice may bring awareness of how mental health workers reflect, learn and practice professional 'artistry'. The aim of the article was to explore mental health workers' processes of development and learning as they appeared in focus groups intended to develop practical wisdom. The main research question was 'How might the processes of development and learning contribute to developing practical wisdom in the individual as well as in the practice culture?' The design was multi-stage focus groups, and the same participants met four times. A phenomenological hermeneutical method for researching lived experience guided the analysis. Eight experienced mental health workers representing four Norwegian municipalities participated. The research context was community-based mental health services. The study was reported to Norwegian Social Data Services, and procedures for informed consent were followed. Two examples of processes of re-evaluation of experience (Association, Integration, Validation, Appropriation and Outcomes and action) were explored. The health workers had developed knowledge in previous encounters with clients. In sharing practice experiences, this knowledge was expressed and developed, and also tested and validated against the aims of practice. Discussions led to adapted and extended knowledge, and as tacit knowledge was expressed it could be used actively. Learning to reflect, being ready to be provoked and learning to endure indecisiveness may be foundational in developing practical wisdom. Openness is demanding, and changing habits of mind is difficult. Reflection on, and confrontation with, set practices are

  5. Optimizing Transcriptome Assemblies for Eleusine indica Leaf and Seedling by Combining Multiple Assemblies from Three De Novo Assemblers

    Directory of Open Access Journals (Sweden)

    Shu Chen

    2015-03-01

    Full Text Available Due to rapid advances in sequencing technology, increasing amounts of genomic and transcriptomic data are available for plant species, presenting enormous challenges for biocomputing analysis. A crucial first step for a successful transcriptomics-based study is the building of a high-quality assembly. Here, we utilized three different de novo assemblers (Trinity, Velvet, and CLC and the EvidentialGene pipeline tr2aacds to assemble two optimized transcript sets for the notorious weed species, . Two RNA sequencing (RNA-seq datasets from leaf and aboveground seedlings were processed using three assemblers, which resulted in 20 assemblies for each dataset. The contig numbers and N50 values of each assembly were compared to study the effect of read number, k-mer size, and in silico normalization on assembly output. The 20 assemblies were then processed through the tr2aacds pipeline to remove redundant transcripts and to select the transcript set with the best coding potential. Each assembly contributed a considerable proportion to the final transcript combination with the exception of the CLC-k14. Thus each assembler and parameter set did assemble better contigs for certain transcripts. The redundancy, total contig number, N50, fully assembled contig number, and transcripts related to target-site herbicide resistance were evaluated for the EvidentialGene and Trinity assemblies. Comparing the EvidentialGene set with the Trinity assembly revealed improved quality and reduced redundancy in both leaf and seedling EvidentialGene sets. The optimized transcriptome references will be useful for studying herbicide resistance in and the evolutionary process in the three allotetraploid offspring.

  6. PRACTICAL CONTRIBUTIONS TO THE STUDY OF RESISTANCE ASSEMBLIES MADE WITH WARP KNITS

    Directory of Open Access Journals (Sweden)

    OANA Ioan-Pavel

    2014-05-01

    Full Text Available Based on the principle that a body to be obtained by sewing the material to provide resistance and the like in the stitching assembly, the experimental study of which developed resistance is compared with the resistance materials to effectively assembled by the assembly line. The experimental values resistance for assemblies were obtained in the testing for resistance to sliding stitch ASTM D 434 using Tinius Olsen HK5T test type machine. The assembly strength was determined for warp knitted fabric and satin charmeuse, made of poly-filamentary wires and mono-filament polyester and polyamide. Resistance assembling is one of the major determinants of the quality of the stitching. It is defined as "the tensile strength or friction." Tenacity stitching seam rupture is the force recorded at its weakest point. Seam abrasion resistance is the number of cycles required friction mesh destruction of seam. It can be said that the strength of the used assembly, the seam 301 is achieved by, in most of the cases, lower resistance knitted studied. In these cases, the primary findings presented, it is clear that the assembly is not appropriate in terms of reliability and maintainability of the product. Such a situation requires a first step to change the type (class of stitch used. Another way to remedy the deficiencies could be using a sewing thread with a lower finesse or strength in grain, especially in the upper loop of wire used in the study-specific.

  7. Lead and Cadmium Toxicity in Tile Manufacturing Workers in Assiut, Egypt

    Directory of Open Access Journals (Sweden)

    Ragaa M Abd Elmaaboud

    2016-06-01

    Full Text Available Occupational lead and cadmium exposure are important health issues in developing countries. This study aimed to detect toxic metal contents in raw materials used to make tiles and to assess exposure health impacts on workers. The study sample consisted of 74 tile workers, having a mean age of 35.2 years, in the Industrial City of Arab El Awamer, Assiut (Egypt. Elemental analysis of the raw materials was performed by using scanning electron microscopy. The data collection questionnaire was divided into two parts; the first included demographic data, symptoms attributed to toxic elements and possible sources of exposure to metals. The second part was designated to assess heavy metal exposure health impacts through clinical examination and biological  investigations. Many toxic elements were identified in the raw materials used to make tiles, and the most abundant were lead and cadmium. Analysis of the clinical data revealed that 66% of the workers suffered from headache, constipation (8%, abdominal colic (33.8% and 30% suffered from a variety of respiratory problems such as dyspnea (60%, cough (13% and chest tightness (27%. Fifty percent of the workers complained of weak grip, 33.8% of foot drop, and 54% had tremors. Burton’s line in gums was present in 28% of workers and 28.2% were diagnosed with constrictive lung diseases. Of the 74 workers, 90.5 % showed toxic lead levels and 80% had toxic cadmium levels. 10.8% had abnormal alpha glutathione levels with a positive strong linear correlation between lead and cadmium levels and years of work. It is mandatory to develop and implement measures to prevent these hazardous exposure effects among tile industry workers.

  8. Passive gamma analysis of the boiling-water-reactor assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Vo, D., E-mail: ducvo@lanl.gov [Los Alamos National Laboratory, Los Alamos, NM (United States); Favalli, A. [Los Alamos National Laboratory, Los Alamos, NM (United States); Grogan, B. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Jansson, P. [Uppsala University, Uppsala (Sweden); Liljenfeldt, H. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Mozin, V. [Lawrence Livermore National Laboratory, Livermore, CA (United States); Schwalbach, P. [European Atomic Energy Community (EURATOM), Luxemburg (Luxembourg); Sjöland, A. [Swedish Nuclear Fuel and Waste Management Company, Stockholm (Sweden); Tobin, S.; Trellue, H. [Los Alamos National Laboratory, Los Alamos, NM (United States); Vaccaro, S. [European Atomic Energy Community (EURATOM), Luxemburg (Luxembourg)

    2016-09-11

    This research focused on the analysis of a set of stationary passive gamma measurements taken on the spent nuclear fuel assemblies from a boiling water reactor (BWR) using pulse height analysis data acquisition. The measurements were performed on 25 different BWR assemblies in 2014 at Sweden's Central Interim Storage Facility for Spent Nuclear Fuel (Clab). This study was performed as part of the Next Generation of Safeguards Initiative–Spent Fuel project to research the application of nondestructive assay (NDA) to spent fuel assemblies. The NGSI–SF team is working to achieve the following technical goals more easily and efficiently than in the past using nondestructive assay (NDA) measurements of spent fuel assemblies: (1) verify the initial enrichment, burnup, and cooling time of facility declaration; (2) detect the diversion or replacement of pins, (3) estimate the plutonium mass, (4) estimate the decay heat, and (5) determine the reactivity of spent fuel assemblies. The final objective of this project is to quantify the capability of several integrated NDA instruments to meet the aforementioned goals using the combined signatures of neutrons, gamma rays, and heat. This report presents a selection of the measured data and summarizes an analysis of the results. Specifically, trends in the count rates measured for spectral lines from the following isotopes were analyzed as a function of the declared burnup and cooling time: {sup 137}Cs, {sup 154}Eu, {sup 134}Cs, and to a lesser extent, {sup 106}Ru and {sup 144}Ce. From these measured count rates, predictive algorithms were developed to enable the estimation of the burnup and cooling time. Furthermore, these algorithms were benchmarked on a set of assemblies not included in the standard assemblies set used by this research team.

  9. Atlas transmission line/transition design and fabrication status

    CERN Document Server

    Ballard, E O; Davis, H A; Elizondo, J M; Gribble, R F; Nielsen, K E; Parker, G V; Ricketts, R L; Valdez, G A

    1999-01-01

    Atlas is a pulsed-power facility under development at Los Alamos National Laboratory to drive high-energy density experiments. Design has been completed for this new generation pulsed-power machine consisting of an azimuthal array of 24, 240-kV Marx modules and transmission lines supplying current to the load region at the machine center. The transmission line consists of a cable header, load protection switch, and tri-plate assembly interfacing to the center transition section. The cable header interface to the Marx module provides a mechanism to remove the Marx module for maintenance without removing other components of the transmission line. The load protection switch provides a mechanism for protecting the load during charging of the Marx in the event of a pre-fire condition. The aluminum tri-plate is a low-inductance transmission line that carries radial current flow from the Marx energy storage system at the machine periphery toward the load. All transmission line components are oil insulated except the...

  10. The HERrespect intervention to address violence against female garment workers in Bangladesh: study protocol for a quasi-experimental trial.

    Science.gov (United States)

    Al Mamun, Mahfuz; Parvin, Kausar; Yu, Marat; Wan, Jessica; Willan, Samantha; Gibbs, Andrew; Jewkes, Rachel; Naved, Ruchira Tabassum

    2018-04-18

    Women in Bangladesh experience high rates of Intimate Partner Violence (IPV). IPV is more prevalent against income earning women compared to their non-earning counterparts, and Workplace Violence (WPV) is also common. Such violence is a violation of women's rights, and also constrains them from contributing to their personal growth, household, community and the economy at large. There is limited evidence on what works to prevent IPV and WPV amongst garment workers. This paper describes an evaluation of HERrespect, an intervention which aims to reduce IPV and WPV against female garment workers in and around Dhaka, Bangladesh. The trial employs a quasi-experimental design, with four intervention and four control factories. In the intervention factories a randomly selected cohort of married female line workers, a cohort of male line workers, and all middle management staff received the intervention. The intervention strategies involved (1) gender transformative group-based training for workers and management staff; (2) joint session between workers (15 female and male) and middle-management staff; (3) factory-wide activities; (4) awareness raising among top management; (5) factory policy review and development and 6) a community based campaign. For the evaluation, a cohort of randomly selected female workers and a cohort of selected management staff have been established. All workers (n = 800) and management staff (n = 395) from these cohorts were interviewed at baseline using two different questionnaires, and will be interviewed in the endline, 24 months post-baseline. Intention to treat analysis will be used for assessing the impact of HERrespect, comparing the intervention and control factories. To our knowledge this is the first study that seeks to evaluate the impact on IPV and WPV, of group sessions with female workers, male workers, and management; factory-wide campaigns and a community intervention among female garment workers in Bangladesh. Apart

  11. Plural beam electron gun assembly

    International Nuclear Information System (INIS)

    Stratton, M.G.

    1977-01-01

    The invention relates to a cathode ray tube plural-beam-in-line bi-potential electron gun assembly, having applied beam currents of differing levels, manifests structurally modified gun structures to effect focused beam landings at the screen that are evidenced as substantially equi-sized spots thereby providing improved resolution and brightness of the screen imagery. The structural changes embody modifications of the related focusing and accelerator electrodes of the respective guns to provide a partial telescoping arrangement for effecting the discrete placement, forming and shielding of the final focusing lenses. The three lenses so formed are in different planes in partial overlapping axial relationship

  12. Maternal Health Phone Line: Saving Women in Papua New Guinea

    Directory of Open Access Journals (Sweden)

    Amanda H.A. Watson

    2015-04-01

    Full Text Available This paper presents the findings of a research project which has involved the establishment of a maternal health phone line in Milne Bay Province of Papua New Guinea (PNG. Mobile phones and landline phones are key information and communication technologies (ICTs. This research study uses the “ICTs for healthcare development” model to ascertain benefits and barriers to the successful implementation of the Childbirth Emergency Phone. PNG has a very high maternal mortality rate. The “three stages of delay” typology was developed by Thaddeus and Maine to determine factors that might delay provision of appropriate medical treatment and hence increase risk of maternal death. The “three stages of delay” typology has been utilised in various developing countries and also in the present study. Research undertaken has involved semi-structured interviews with health workers, both in rural settings and in the labour ward in Alotau. Additional data has been gathered through focus groups with health workers, analysis of notes made during phone calls, interviews with women and community leaders, observations and field visits. One hundred percent of interviewees (n = 42 said the project helped to solve communication barriers between rural health workers and Alotau Provincial Hospital. Specific examples in which the phone line has helped to create positive health outcomes will be outlined in the paper, drawn from research interviews. The Childbirth Emergency Phone project has shown itself to play a critical role in enabling healthcare workers to address life-threatening childbirth complications. The project shows potential for rollout across PNG; potentially reducing maternal morbidity and maternal mortality rates by overcoming communication challenges.

  13. Maternal Health Phone Line: Saving Women in Papua New Guinea

    Science.gov (United States)

    Watson, Amanda H.A.; Sabumei, Gaius; Mola, Glen; Iedema, Rick

    2015-01-01

    This paper presents the findings of a research project which has involved the establishment of a maternal health phone line in Milne Bay Province of Papua New Guinea (PNG). Mobile phones and landline phones are key information and communication technologies (ICTs). This research study uses the “ICTs for healthcare development” model to ascertain benefits and barriers to the successful implementation of the Childbirth Emergency Phone. PNG has a very high maternal mortality rate. The “three stages of delay” typology was developed by Thaddeus and Maine to determine factors that might delay provision of appropriate medical treatment and hence increase risk of maternal death. The “three stages of delay” typology has been utilised in various developing countries and also in the present study. Research undertaken has involved semi-structured interviews with health workers, both in rural settings and in the labour ward in Alotau. Additional data has been gathered through focus groups with health workers, analysis of notes made during phone calls, interviews with women and community leaders, observations and field visits. One hundred percent of interviewees (n = 42) said the project helped to solve communication barriers between rural health workers and Alotau Provincial Hospital. Specific examples in which the phone line has helped to create positive health outcomes will be outlined in the paper, drawn from research interviews. The Childbirth Emergency Phone project has shown itself to play a critical role in enabling healthcare workers to address life-threatening childbirth complications. The project shows potential for rollout across PNG; potentially reducing maternal morbidity and maternal mortality rates by overcoming communication challenges. PMID:25923199

  14. Fast Neutron Emission Tomography of Used Nuclear Fuel Assemblies

    Science.gov (United States)

    Hausladen, Paul; Iyengar, Anagha; Fabris, Lorenzo; Yang, Jinan; Hu, Jianwei; Blackston, Matthew

    2017-09-01

    Oak Ridge National Laboratory is developing a new capability to perform passive fast neutron emission tomography of spent nuclear fuel assemblies for the purpose of verifying their integrity for international safeguards applications. Most of the world's plutonium is contained in spent nuclear fuel, so it is desirable to detect the diversion of irradiated fuel rods from an assembly prior to its transfer to ``difficult to access'' storage, such as a dry cask or permanent repository, where re-verification is practically impossible. Nuclear fuel assemblies typically consist of an array of fuel rods that, depending on exposure in the reactor and consequent ingrowth of 244Cm, are spontaneous sources of as many as 109 neutrons s-1. Neutron emission tomography uses collimation to isolate neutron activity along ``lines of response'' through the assembly and, by combining many collimated views through the object, mathematically extracts the neutron emission from each fuel rod. This technique, by combining the use of fast neutrons -which can penetrate the entire fuel assembly -and computed tomography, is capable of detecting vacancies or substitutions of individual fuel rods. This paper will report on the physics design and component testing of the imaging system. This material is based upon work supported by the U.S. Department of Energy, Office of Defense Nuclear Nonproliferation Research and Development within the National Nuclear Security Administration, under Contract Number DE-AC05-00OR22725.

  15. Fuel assemblies

    International Nuclear Information System (INIS)

    Nakatsuka, Masafumi.

    1979-01-01

    Purpose: To prevent scattering of gaseous fission products released from fuel assemblies stored in an fbr type reactor. Constitution; A cap provided with means capable of storing gas is adapted to amount to the assembly handling head, for example, by way of threading in a storage rack of spent fuel assemblies consisting of a bottom plate, a top plate and an assembly support mechanism. By previously eliminating the gas inside of the assembly and the cap in the storage rack, gaseous fission products upon loading, if released from fuel rods during storage, are stored in the cap and do not scatter in the storage rack. (Horiuchi, T.)

  16. A dented LH2 recirculation line is removed from Discovery

    Science.gov (United States)

    1999-01-01

    In the Payload Changeout Room, Launch Pad 39B, United Space Alliance and NASA workers look at the replacement main propulsion system liquid hydrogen recirculation line (left) to be installed in Shuttle Discovery's aft compartment. At right is the dented line that has been removed. The 12-inch-long dent was discovered during routine aft compartment inspections Tuesday, Dec. 7. The line recirculates hydrogen from the Shuttle main engines back to the external tank during prelaunch engine conditioning. The line is being replaced and managers expect the replacement work to take about 3 days, followed by system retests and final aft compartment close-outs. Preliminary assessments reflect a launch date of Space Shuttle Discovery on mission STS-103 no earlier than Dec. 16. STS-103 is the third servicing mission for the Hubble Space Telescope.

  17. Assembly of silver nanowire ring induced by liquid droplet

    Science.gov (United States)

    Seong, Baekhoon; Park, Hyun Sung; Chae, Ilkyeong; Lee, Hyungdong; Wang, Xiaofeng; Jang, Hyung-Seok; Jung, Jaehyuck; Lee, Changgu; Lin, Liwei; Byun, Doyoung

    2017-11-01

    Several forces in the liquid droplet drive the nanomaterials to naturally form an assembled structure. During evaporation of a liquid droplet, nanomaterials can move to the rim of the droplet by convective flow and capillary flow, due to the difference in temperature between the top and contact line of the droplet. Here, we demonstrate a new, simple and scalable technology for the fabrication of ring-shaped Ag NWs by a spraying method. We experimentally identify the compressive force of the droplet driven by surface tension as the key mechanism for the self-assembly of ring structures. We investigated the progress of ring shape formation of Ag NWs according to the droplet size with theoretically calculated optimal conditions. As such, this self-assembly technique of making ring-shaped structures from Ag NWs could be applied to other nanomaterials. This work was supported by the New & Renewable Energy R&D program of the Korea Institute of Energy Technology Evaluation and Planning (KETEP) Grant funded by the Korea government Ministry of Trade, Industry and Energy. (No. 20163010071630).

  18. The One-Pot Directed Assembly of Cylinder-Forming Block Copolymer on Adjacent Chemical Patterns for Bimodal Patterning.

    Science.gov (United States)

    Chang, Tzu-Hsuan; Xiong, Shisheng; Liu, Chi-Chun; Liu, Dong; Nealey, Paul F; Ma, Zhenqiang

    2017-09-01

    The direct self-assembly of cylinder-forming poly(styrene-block-methyl-methacrylate) (PS-b-PMMA) block copolymer is successfully assembled into two orientations, according to the underlying guiding pattern in different areas. Lying-down and perpendicular cylinders are formed, respectively, depending on the design of chemical pattern: sparse line/space pattern or hexagonal dot array. The first chemical pattern composed of prepatterned cross-linked polystyrene (XPS) line/space structure has a period (L S ) equal to twice the intercylinder period of the block copolymer (L 0 ). The PS-b-PMMA thin film on the prepared chemical template after thermal annealing forms a lying-down cylinder morphology when the width of the PS strips is less than the width of PS block in the PS-b-PMMA block copolymer. The morphology is only applicable at the discrete thickness of the PS-b-PMMA film. In addition to forming the lying-down cylinders directly on the XPS guiding pattern, the cylinder-forming block copolymer can also be assembled in a perpendicular way on the second guiding pattern (the hexagonal dot array). The block copolymer films are registered into two orientations in a single directed self-assembly process. The features of the assembled patterns are successfully transferred down to the silicon oxide substrate. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. Establishment and mitotic characterization of new Drosophila acentriolar cell lines from DSas-4 mutant

    Directory of Open Access Journals (Sweden)

    Nicolas Lecland

    2013-01-01

    In animal cells the centrosome is commonly viewed as the main cellular structure driving microtubule (MT assembly into the mitotic spindle apparatus. However, additional pathways, such as those mediated by chromatin and augmin, are involved in the establishment of functional spindles. The molecular mechanisms involved in these pathways remain poorly understood, mostly due to limitations inherent to current experimental systems available. To overcome these limitations we have developed six new Drosophila cell lines derived from Drosophila homozygous mutants for DSas-4, a protein essential for centriole biogenesis. These cells lack detectable centrosomal structures, astral MT, with dispersed pericentriolar proteins D-PLP, Centrosomin and γ-tubulin. They show poorly focused spindle poles that reach the plasma membrane. Despite being compromised for functional centrosome, these cells could successfully undergo mitosis. Live-cell imaging analysis of acentriolar spindle assembly revealed that nascent MTs are nucleated from multiple points in the vicinity of chromosomes. These nascent MTs then grow away from kinetochores allowing the expansion of fibers that will be part of the future acentriolar spindle. MT repolymerization assays illustrate that acentriolar spindle assembly occurs “inside-out” from the chromosomes. Colchicine-mediated depolymerization of MTs further revealed the presence of a functional Spindle Assembly Checkpoint (SAC in the acentriolar cells. Finally, pilot RNAi experiments open the potential use of these cell lines for the molecular dissection of anastral pathways in spindle and centrosome assembly.

  20. Evaluation on the Radiation Exposure of Radiation Workers in Proton Therapy

    International Nuclear Information System (INIS)

    Lee, Seung Hyun; Jang, Yo Jong; Kim, Tae Yoon; Jeong, Do Hyung; Choi, Gye Suk

    2012-01-01

    Unlike the existing linear accelerator with photon, proton therapy produces a number of second radiation due to the kinds of nuclide including neutron that is produced from the interaction with matter, and more attention must be paid on the exposure level of radiation workers for this reason. Therefore, thermoluminescence dosimeter (TLD) that is being widely used to measure radiation was utilized to analyze the exposure level of the radiation workers and propose a basic data about the radiation exposure level during the proton therapy. The subjects were radiation workers who worked at the proton therapy center of National Cancer Center and TLD Badge was used to compare the measured data of exposure level. In order to check the dispersion of exposure dose on body parts from the second radiation coming out surrounding the beam line of proton, TLD (width and length: 3 mm each) was attached to on the body spots (lateral canthi, neck, nipples, umbilicus, back, wrists) and retained them for 8 working hours, and the average data was obtained after measuring them for 80 hours. Moreover, in order to look into the dispersion of spatial exposure in the treatment room, TLD was attached on the snout, PPS (Patient Positioning System), Pendant, block closet, DIPS (Digital Image Positioning System), Console, doors and measured its exposure dose level during the working hours per day. As a result of measuring exposure level of TLD Badge of radiation workers, quarterly average was 0.174 mSv, yearly average was 0.543 mSv, and after measuring the exposure level of body spots, it showed that the highest exposed body spot was neck and the lowest exposed body spot was back (the middle point of a line connecting both scapula superior angles). Investigation into the spatial exposure according to the workers' movement revealed that the exposure level was highest near the snout and as the distance becomes distant, it went lower. Even a small amount of exposure will eventually increase

  1. Preventive actions taken by workers after workers' health surveillance: a controlled trial.

    Science.gov (United States)

    Boschman, J S; Van der Molen, H F; Frings-Dresen, M H W; Sluiter, J K

    2013-12-01

    To evaluate construction workers' preventive actions and occupational physician's (OPs) recommendations after a job-specific workers' health surveillance (WHS) compared with the currently used generic WHS. After the WHS, the OPs' written recommendations were captured. At the 3-month follow-up, the workers were asked about the preventive actions they had undertaken. A generalized linear mixed model was used to compare proportions of workers. At follow-up, the proportion of workers who reported taking preventive actions was significantly higher in the intervention group (80%, 44/55) than in the control group (67%, 80 of 121), (P = 0.04). In the intervention group, the OPs provided a higher proportion of workers with written recommendations (82%, 63 of 77, vs 57%, 69 of 121; P = 0.03). The job-specific WHS aided OPs in providing workers with recommendations and workers in undertaking (job-specific) preventive actions.

  2. 78 FR 75207 - National Pearl Harbor Remembrance Day, 2013

    Science.gov (United States)

    2013-12-10

    ... nations as they progressed. Because of their extraordinary valor, America emerged from this test as we... assembly line alongside workers of every background and realized their own power to build a brighter world... agencies and interested organizations, groups, and individuals to fly the flag of the United States at half...

  3. Developing An Effective Strategy to Configure Assembly Systems Using Lean Concepts

    Directory of Open Access Journals (Sweden)

    M.Eswaramoorthi

    2010-12-01

    Full Text Available The manufacturing industry has been pushed to adopt more effective production strategies to meet the challenges of shorter life cycle, higher quality, lower cost and wider variety of customer demands. This increased emphasis on achieving highly adaptive manufacturing with reduction in manufacturing costs and better utilization of manufacturing resources force to implementing new and efficient management techniques in their manufacturing operations. Some of the established tools in this context are lean practices. In manufacturing, assembly is one of the major activities that combine the machined components into final product. Decision on appropriate facility layout and viable assembly sequence (line balancing adaptable to takt time requirement with cost benefit is a challenging task. This paper proposes an integrated cost model for a typical assembly process to determine cost per part more precisely by considering seven types of "contributing factors". This procedure is performed under different takt time conditions to configure the assembly system in terms of cost per piece and to decide the adaptable layout. A prototype assembly system is established in this research to demonstrate the effectiveness of the cost model. The results show that there are significant variations in cost per piece with respect to changes in layout configurations and takt time.

  4. Integrating Robot Task Planning into Off-Line Programming Systems

    DEFF Research Database (Denmark)

    Sun, Hongyan; Kroszynski, Uri

    1988-01-01

    a system architecture for integrated robot task planning. It identifies and describes the components considered necessary for implementation. The focus is on functionality of these elements as well as on the information flow. A pilot implementation of such an integrated system architecture for a robot......The addition of robot task planning in off-line programming systems aims at improving the capability of current state-of-the-art commercially available off-line programming systems, by integrating modeling, task planning, programming and simulation together under one platform. This article proposes...... assembly task is discussed....

  5. A peptide extension dictates IgM assembly.

    Science.gov (United States)

    Pasalic, Dzana; Weber, Benedikt; Giannone, Chiara; Anelli, Tiziana; Müller, Roger; Fagioli, Claudio; Felkl, Manuel; John, Christine; Mossuto, Maria Francesca; Becker, Christian F W; Sitia, Roberto; Buchner, Johannes

    2017-10-10

    Professional secretory cells can produce large amounts of high-quality complex molecules, including IgM antibodies. Owing to their multivalency, polymeric IgM antibodies provide an efficient first-line of defense against pathogens. To decipher the mechanisms of IgM assembly, we investigated its biosynthesis in living cells and faithfully reconstituted the underlying processes in vitro. We find that a conserved peptide extension at the C-terminal end of the IgM heavy (Ig-μ) chains, termed the tailpiece, is necessary and sufficient to establish the correct geometry. Alanine scanning revealed that hydrophobic amino acids in the first half of the tailpiece contain essential information for generating the correct topology. Assembly is triggered by the formation of a disulfide bond linking two tailpieces. This induces conformational changes in the tailpiece and the adjacent domain, which drive further polymerization. Thus, the biogenesis of large and topologically challenging IgM complexes is dictated by a local conformational switch in a peptide extension.

  6. Buildup of radioxenon isotopes in MOX-assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Gniffke, Thomas; Kirchner, Gerald [Carl Friedrich von Weizsaecker-Centre for Science and Peace Research, Hamburg (Germany)

    2015-07-01

    Radioxenon is the main tracer for detection of nuclear tests conducted underground under the verification regime of the Comprehensive Nuclear Test Ban Treaty (CTBT). Since radioxenon is emitted by civilian sources too, like commercial nuclear reactors, source discrimination is still an important issue. Inventory calculations are necessary to predict which xenon isotopic ratios are built up in a reactor and how they differ from those generated by a nuclear explosion. The screening line actually used by the CTBT Organization for source discrimination is based on calculations for uranium fuel of various enrichments used in pressurized water reactors (PWRs). The usage of different fuel, especially mixed U/Pu oxide (MOX) assemblies with reprocessed plutonium, may alter the radioxenon signature of civilian reactors. In this talk, calculations of the radioxenon buildup in a MOX-assembly used in a commercial PWR are presented. Implications for the CTBT verification regimes are discussed and open questions are addressed.

  7. Fuel assembly and fuel cladding tube

    International Nuclear Information System (INIS)

    Tsutsumi, Shinro; Ito, Ken-ichi; Inagaki, Masatoshi; Nakajima, Junjiro.

    1996-01-01

    A fuel cladding tube is a zirconium liner tube formed by lining a pure zirconium layer on the inner side of a zirconium alloy tube. The fuel cladding tube is formed by extrusion molding of a composite billet formed by inserting a pure zirconium billet into a zirconium alloy billet. Accordingly, the pure zirconium layer and the zirconium alloy tube are strongly joined by metal bond. The fuel cladding tube has an external oxide film on the outer surface of the zirconium alloy tube and an internal oxide film on the inner side of the pure zirconium layer. The external oxide film has a thickness preferably of about 1μm. The internal oxide film has a thickness of not more than 10μm, preferably, from 1 to 5μm. With such a constitution, flaws to be formed on both inner and outer surfaces of the cladding tube upon assembling a fuel assembly can be reduced thereby enabling to reduce the amount of hydrogen absorbed to the cladding tube. (I.N.)

  8. Radiological Worker Training: Radiological Worker 2 study guides

    International Nuclear Information System (INIS)

    1992-10-01

    Upon completion of this training course, the participant will have the knowledge to work safely in areas controlled for radiological purposes using proper radiological practices. Radiological Worker H Training, for the worker whose job assignment involves entry into Radiological Buffer Areas and all types of Radiation Contamination and Airborne Radioactivity Areas. This course is designed to prepare the worker to work safely in and around radiological areas and present methods to use to ensure individual radiation exposure is maintained As Low As Reasonably Achievable

  9. Study on assembly techniques and procedures for ITER tokamak device

    International Nuclear Information System (INIS)

    Obara, Kenjiro; Kakudate, Satoshi; Shibanuma, Kiyoshi; Sago, Hiromi; Ue, Koichi; Shimizu, Katsusuke; Onozuka, Masanori

    2006-06-01

    concept based on the available knowledge and experiences of the installation of the large components, in order to improve the IT (International Team) design toward the more realistic one. As a result, we show the realistic tokamak assembly procedures and techniques to be able to assemble the large and heavy ITER tokamak with high accuracy. 1) Assembly and alignment of the TF coil with high accuracy, considering the influences of the magnetic field error. 2) Simplification of the assembly procedures, and the jigs/tools and procedures to reduce the misalignment. 3) Assembly procedures and techniques for the 40deg sector to reduce the weld distortion. 4) Supporting procedures and techniques of the VV sector to prevent the TF coil from the deformation due to the dead weight of the VV sector. 5) Datum points and lines for the required positions and assembly tolerances during tokamak assembly. (author)

  10. HB-Line Plutonium Oxide Data Collection Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, R. [Savannah River Nuclear Solutions; Varble, J. [Savannah River Nuclear Solutions; Jordan, J. [Savannah River Nuclear Solutions

    2015-05-26

    HB-Line and H-Canyon will handle and process plutonium material to produce plutonium oxide for feed to the Mixed Oxide Fuel Fabrication Facility (MFFF). However, the plutonium oxide product will not be transferred to the MFFF directly from HB-Line until it is packaged into a qualified DOE-STD-3013-2012 container. In the interim, HB-Line will load plutonium oxide into an inner, filtered can. The inner can will be placed in a filtered bag, which will be loaded into a filtered outer can. The outer can will be loaded into a certified 9975 with getter assembly in compliance with onsite transportation requirement, for subsequent storage and transfer to the K-Area Complex (KAC). After DOE-STD-3013-2012 container packaging capabilities are established, the product will be returned to HB-Line to be packaged into a qualified DOE-STD-3013-2012 container. To support the transfer of plutonium oxide to KAC and then eventually to MFFF, various material and packaging data will have to be collected and retained. In addition, data from initial HB-Line processing operations will be needed to support future DOE-STD-3013-2012 qualification as amended by the HB-Line DOE Standard equivalency. As production increases, the volume of data to collect will increase. The HB-Line data collected will be in the form of paper copies and electronic media. Paper copy data will, at a minimum, consist of facility procedures, nonconformance reports (NCRs), and DCS print outs. Electronic data will be in the form of Adobe portable document formats (PDFs). Collecting all the required data for each plutonium oxide can will be no small effort for HB-Line, and will become more challenging once the maximum annual oxide production throughput is achieved due to the sheer volume of data to be collected. The majority of the data collected will be in the form of facility procedures, DCS print outs, and laboratory results. To facilitate complete collection of this data, a traveler form will be developed which

  11. Spatial Manipulation and Assembly of Nanoparticles by Atomic Force Microscopy Tip-Induced Dielectrophoresis.

    Science.gov (United States)

    Zhou, Peilin; Yu, Haibo; Yang, Wenguang; Wen, Yangdong; Wang, Zhidong; Li, Wen Jung; Liu, Lianqing

    2017-05-17

    In this article, we present a novel method of spatial manipulation and assembly of nanoparticles via atomic force microscopy tip-induced dielectrophoresis (AFM-DEP). This method combines the high-accuracy positioning of AFM with the parallel manipulation of DEP. A spatially nonuniform electric field is induced by applying an alternating current (AC) voltage between the conductive AFM probe and an indium tin oxide glass substrate. The AFM probe acted as a movable DEP tweezer for nanomanipulation and assembly of nanoparticles. The mechanism of AFM-DEP was analyzed by numerical simulation. The effects of solution depth, gap distance, AC voltage, solution concentration, and duration time were experimentally studied and optimized. Arrays of 200 nm polystyrene nanoparticles were assembled into various nanostructures, including lines, ellipsoids, and arrays of dots. The sizes and shapes of the assembled structures were controllable. It was thus demonstrated that AFM-DEP is a flexible and powerful tool for nanomanipulation.

  12. Sensor mount assemblies and sensor assemblies

    Science.gov (United States)

    Miller, David H [Redondo Beach, CA

    2012-04-10

    Sensor mount assemblies and sensor assemblies are provided. In an embodiment, by way of example only, a sensor mount assembly includes a busbar, a main body, a backing surface, and a first finger. The busbar has a first end and a second end. The main body is overmolded onto the busbar. The backing surface extends radially outwardly relative to the main body. The first finger extends axially from the backing surface, and the first finger has a first end, a second end, and a tooth. The first end of the first finger is disposed on the backing surface, and the tooth is formed on the second end of the first finger.

  13. Worker participation - the Netherlands

    OpenAIRE

    Kwantes, J.H.

    2014-01-01

    Worker participation relates to the involvement of workers in the management decision-making processes. In this article attention is focused on worker participation related to occupational safety and health in the Netherlands. Worker participation can refer either to direct or indirect participation by the worker. Indirect participation involves employee representation, while direct participation relates to individual involvement in management’s decision-making processes. In the Framework Dir...

  14. Surfactant self-assembly in alcohol-rich solutions

    International Nuclear Information System (INIS)

    Bouguerra, N.; Jebari, M.M.; Gomati, R.; Gharbi, A.

    2005-01-01

    Ionic conductivity and viscosity measurements are achieved along alcohol dilution lines of a single-isotropic phase domain, which extends from the alcohol corner to sponge phase domain to brine corner, of an alcohol-surfactant-brine phase diagram. The results are discussed in terms of amphiphilic self-assembly which leads to stable mixtures of the slightly miscible alcohol and brine used. We show the formation of reverse micelles, whose cores are either dry or charged of brine according to the samples composition, and whose sizes remain small near the sponge phase structure

  15. Worker participation - the Netherlands

    NARCIS (Netherlands)

    Kwantes, J.H.

    2014-01-01

    Worker participation relates to the involvement of workers in the management decision-making processes. In this article attention is focused on worker participation related to occupational safety and health in the Netherlands. Worker participation can refer either to direct or indirect participation

  16. Urinary lithiasis in civil construction workers as a management indicator for health and improvement in personnel

    Directory of Open Access Journals (Sweden)

    Renato Ribeiro Nogueira Ferraz

    2014-12-01

    Full Text Available Introduction: Empirical information provided by health care professionals acting in the first line of care report a constant increase in the number of civil construction workers that present painful acute conditions, in most cases associated with the existence of urinary tract calculi. Aims: Evaluating the prevalence of urinary lithiasis in civil construction workers, as a means to identify indicators for the management of health and personnel. Methods: Observational study based on directed questionnaire. Results: From the 94 participants, 18 (19% were lithiasic, mostly due to overweight and reduced fluid intake. Conclusion: The observed prevalence appeared to be two times greater than that of the general population. Thus, prevention for such condition gains relevance, in order to avoid discomfort for the worker, and also reduce costs due to absenteeism, improving productivity, benefiting the workers by performance and creating the perspective of an improved quality of life.

  17. Measurements of time dependent energy spectra of neutrons in a small graphite assembly

    International Nuclear Information System (INIS)

    Fujita, Yoshiaki; Sakamoto, Shigeyasu; Aizawa, Otohiko; Takahashi, Akito; Sumita, Kenji.

    1975-01-01

    The time-dependent energy spectra of neutrons have been measured in a small 30x30x30 cm 3 graphite assembly by means of the linac-chopper method, with a view to establishing experimental evidence that there is no asymptotic spectrum in such a small assembly, and in order to study the non-asymptotic behavior of neutrons. The arrangement of a polyethylene pre-moderator adjacent to the assembly made the measurements possible with the improvement obtained thereby of the neutron counting statistics. It was indicated from calculation that the presence of the pre-moderator had little effect - at least above the Bragg cut-off energy - on the evolution in time of the energy spectra of neutrons in the graphite assembly. The experimental results indicated very probable disappearance of asymptotic spectra, and revealed significant enhancement of trapping at Bragg energies with the lapse of time. This is consistent with the results of pulsed neutron experiments in small assemblies conducted by Takahashi et al., and falls in line with de Saussure's approximation. The spectra in the graphite assembly showed significant space dependence, the spectra becoming harder with increasing distance from the pre-moderator. This hardening may be attributed to the relatively faster propagation of higher energy neutrons. (auth.)

  18. Hypothenar hammer syndrome in an office worker.

    Science.gov (United States)

    Zhang, Fan; Weerakkody, Yuranga; Tosenovsky, Patrik

    2017-12-01

    Hypothenar hammer syndrome (HHS) is an uncommon cause of unilateral Raynaud's phenomenon, splinter haemorrhages and hypothenar weakness. The typical patient is a male blue-collar worker who uses their hypothenar eminence to hammer objects as part of their work. The distal ulnar artery beyond Guyon's canal is superficial and vulnerable to blunt trauma. CTA and MRA are common initial investigations and can suggest the diagnosis. DSA is the gold standard imaging modality and offers therapeutic opportunities. Management is controversial, but unless there is critical digital ischaemia, conservative treatment is first line. © 2017 The Royal Australian and New Zealand College of Radiologists.

  19. Workers' Education Methods and Techniques for Rural Workers and Their Organisations: Summary of Views Expressed

    Science.gov (United States)

    Labour Education, 1975

    1975-01-01

    Several issues concerning rural workers' organizations and workers' education are discussed: motivation for self-organization, workers' education needs of rural workers, workers' education methods and techniques, training institutions and training personnel, financial resources, and the role of the International Labor Organization workers'…

  20. Epigenetic and Transcriptional Modifications in Repetitive Elements in Petrol Station Workers Exposed to Benzene and MTBE

    Directory of Open Access Journals (Sweden)

    Federica Rota

    2018-04-01

    Full Text Available Benzene, a known human carcinogen, and methyl tert-butyl ether (MTBE, not classifiable as to its carcinogenicity, are fuel-related pollutants. This study investigated the effect of these chemicals on epigenetic and transcriptional alterations in DNA repetitive elements. In 89 petrol station workers and 90 non-occupationally exposed subjects the transcriptional activity of retrotransposons (LINE-1, Alu, the methylation on repeated-element DNA, and of H3K9 histone, were investigated in peripheral blood lymphocytes. Median work shift exposure to benzene and MTBE was 59 and 408 µg/m3 in petrol station workers, and 4 and 3.5 µg/m3, in controls. Urinary benzene (BEN-U, S-phenylmercapturic acid, and MTBE were significantly higher in workers than in controls, while trans,trans-muconic acid (tt-MA was comparable between the two groups. Increased BEN-U was associated with increased Alu-Y and Alu-J expression; moreover, increased tt-MA was associated with increased Alu-Y and Alu-J and LINE-1 (L1-5′UTR expression. Among repetitive element methylation, only L1-Pa5 was hypomethylated in petrol station workers compared to controls. While L1-Ta and Alu-YD6 methylation was not associated with benzene exposure, a negative association with urinary MTBE was observed. The methylation status of histone H3K9 was not associated with either benzene or MTBE exposure. Overall, these findings only partially support previous observations linking benzene exposure with global DNA hypomethylation.

  1. Contact allergic dermatitis from melamine formaldehyde resins in a patient with a negative patch-test reaction to formaldehyde.

    Science.gov (United States)

    García Gavin, Juan; Loureiro Martinez, Manuel; Fernandez-Redondo, Virginia; Seoane, Maria-José; Toribio, Jaime

    2008-01-01

    Melamine paper is a basic material used in the furniture industry for home and office interiors. Contact allergic dermatitis from melamine formaldehyde resins (MFRs) should be considered in patients who work on melamine paper impregnation lines. We report a case of a 28-year-old female plywood worker who developed eczema on the dorsal side of her hands and wrists after 2 years of working on the melamine paper impregnation line. She had a relevant positive patch-test reaction to MFR, with a negative reaction to formaldehyde. Contact dermatitis due to MFR is not common, and it is usually related to products that are not fully cured or to close contact with intermediate products on the assembly line. Formaldehyde release from MFR can explain most of the positive responses. To our knowledge, this is the first report of MFR contact allergic dermatitis in a worker on a melamine paper impregnation line.

  2. Annealing temperature effect on self-assembled Au droplets on Si (111).

    Science.gov (United States)

    Sui, Mao; Li, Ming-Yu; Kim, Eun-Soo; Lee, Jihoon

    2013-12-13

    We investigate the effect of annealing temperature on self-assembled Au droplets on Si (111). The annealing temperature is systematically varied while fixing other growth parameters such as deposition amount and annealing duration clearly to observe the annealing temperature effect. Self-assembled Au droplets are fabricated by annealing from 50°C to 850°C with 2-nm Au deposition for 30 s. With increased annealing temperatures, Au droplets show gradually increased height and diameter while the density of droplets progressively decreases. Self-assembled Au droplets with fine uniformity can be fabricated between 550°C and 800°C. While Au droplets become much larger with increased deposition amount, the extended annealing duration only mildly affects droplet size and density. The results are systematically analyzed with cross-sectional line profiles, Fourier filter transform power spectra, height histogram, surface area ratio, and size and density plots. This study can provide an aid point for the fabrication of nanowires on Si (111).

  3. Transfer hood for handling fuel assemblies in nuclear reactors and especially fast reactors

    International Nuclear Information System (INIS)

    Aubert, M.; Merland, D.; Renaux, C.

    1975-01-01

    A description is given of a hood for transferring fuel assemblies between two or more separate guide ramps inclined to the vertical at the same angle of slope and extending respectively through a first passage into the reactor vessel and through a second passage into a fuel-assembly storage chamber. The hood comprises at least one shielded duct joined to a flanged rotating portion which is so arranged that the open lower end of the shielded duct is positioned in the line of extension of one guide ramp and then the other as a result of displacement of the rotating portion

  4. Dermatologic Diseases in Silk Workers

    Directory of Open Access Journals (Sweden)

    J S Pasricha

    1985-01-01

    Full Text Available A survey of 112 workers of a silk facory near Bangalore, for dermatologic diseases revealed (1 a characteristic wearing off of the medial halves of the distal free edges of the finger nail plates in 10 of the 15 cocoonsorters, (2 maceration of the palms in 58 workers of the boiling and reeling section, and (3 pitted keratolysis of the palms, in 42 workers, also from the boiling and reeling section. There was no clinical evidence of contact dermatitis, and patch tests with the silk thread from the cocoons in 25 workers showed a very mild reaction in 2 workers and a doubtful reaction in another two. In addition, one worker from the skeining section had crisscross superficial fissures on the finger tips caused by friction, two workers had paronychia ′of the fingers and four workers had dermatophytFNx01t fingers webs. As in the previous survey, these workers also had a high incidence of ichthyosis (92 workers and hyperketatosis of the palms (62 workers and soles (110 workers.

  5. Corona performance of a compact 230-kV line

    International Nuclear Information System (INIS)

    Chartier, V.L.; Blair, D.E.

    1994-01-01

    Permitting requirements and the acquisition of new rights-of-way for transmission facilities has in recent years become increasingly difficult for most utilities, including Puget Sound Power and Light Company. In order to maintain a high degree of reliability of service while being responsive to public concerns regarding the siting of high voltage (HV) transmission facilities, Puget Power has found it necessary to more heavily rely upon the use of compact lines in franchise corridors. Compaction does, however, precipitant increased levels of audible noise (AN) and radio and TV interference (RI and TVI) due to corona on the conductors and insulator assemblies. Puget Power relies upon the Bonneville Power Administration (BPA) Corona and Field Effects computer program to calculate AN and RI for new lines. Since there was some question of the program's ability to accurately represent quiet 230-kV compact designs, a joint project was undertaken with BPA to verify the program's algorithms. Long-term measurements made on an operating Puget Power 230-kV compact line confirmed the accuracy of BPA's AN model; however, the RI measurements were much lower than predicted by the BPA computer and other programs. This paper also describes how the BPA computer program can be used to calculate the voltage needed to expose insulator assemblies to the correct electric field in single test setups in HV laboratories

  6. Mobius Assembly: A versatile Golden-Gate framework towards universal DNA assembly.

    Directory of Open Access Journals (Sweden)

    Andreas I Andreou

    Full Text Available Synthetic biology builds upon the foundation of engineering principles, prompting innovation and improvement in biotechnology via a design-build-test-learn cycle. A community-wide standard in DNA assembly would enable bio-molecular engineering at the levels of predictivity and universality in design and construction that are comparable to other engineering fields. Golden Gate Assembly technology, with its robust capability to unidirectionally assemble numerous DNA fragments in a one-tube reaction, has the potential to deliver a universal standard framework for DNA assembly. While current Golden Gate Assembly frameworks (e.g. MoClo and Golden Braid render either high cloning capacity or vector toolkit simplicity, the technology can be made more versatile-simple, streamlined, and cost/labor-efficient, without compromising capacity. Here we report the development of a new Golden Gate Assembly framework named Mobius Assembly, which combines vector toolkit simplicity with high cloning capacity. It is based on a two-level, hierarchical approach and utilizes a low-frequency cutter to reduce domestication requirements. Mobius Assembly embraces the standard overhang designs designated by MoClo, Golden Braid, and Phytobricks and is largely compatible with already available Golden Gate part libraries. In addition, dropout cassettes encoding chromogenic proteins were implemented for cost-free visible cloning screening that color-code different cloning levels. As proofs of concept, we have successfully assembled up to 16 transcriptional units of various pigmentation genes in both operon and multigene arrangements. Taken together, Mobius Assembly delivers enhanced versatility and efficiency in DNA assembly, facilitating improved standardization and automation.

  7. Modeling the Hybrid Flow Shop Scheduling Problem Followed by an Assembly Stage Considering Aging Effects and Preventive Maintenance Activities

    Directory of Open Access Journals (Sweden)

    Seyyed Mohammad Hassan Hosseini

    2016-05-01

    Full Text Available Scheduling problem for the hybrid flow shop scheduling problem (HFSP followed by an assembly stage considering aging effects additional preventive and maintenance activities is studied in this paper. In this production system, a number of products of different kinds are produced. Each product is assembled with a set of several parts. The first stage is a hybrid flow shop to produce parts. All machines can process all kinds of parts in this stage but each machine can process only one part at the same time. The second stage is a single assembly machine or a single assembly team of workers. The aim is to schedule the parts on the machines and assembly sequence and also determine when the preventive maintenance activities get done in order to minimize the completion time of all products (makespan. A mathematical modeling is presented and its validation is shown by solving an example in small scale. Since this problem has been proved strongly NP-hard, in order to solve the problem in medium and large scale, four heuristic algorithms is proposed based on the Johnson’s algorithm. The numerical experiments are used to run the mathematical model and evaluate the performance of the proposed algorithms.

  8. Evaluation of Hose in Hose Transfer Line Service Life for Hanford's Interim Stabilization Program

    International Nuclear Information System (INIS)

    TORRES, T.D.

    2000-01-01

    RPP-6153, Engineering Task Plan for Hose-in-Hose Transfer System for the Interim Stabilization Program, defines the programmatic goals, functional requirements, and technical criteria for the development and subsequent installation of transfer line equipment to support Hanford's Interim Stabilization Program. RPP-6028, Specification for Hose in Hose Transfer Lines for Hanford's Interim Stabilization Program, has been issued to define the specific requirements for the design, manufacture, and verification of transfer line assemblies for specific waste transfer applications. Included in RPP-6028 are tables defining the chemical constituents of concern to which transfer lines will be exposed. Current Interim Stabilization Program planning forecasts that the at-grade transfer lines will be required to convey pumpable waste for as much as three years after commissioning. Prudent engineering dictates that the equipment placed in service have a working life in excess of this forecasted time period, with some margin to allow for future adjustments to the planned schedule. This document evaluates the effective service life of the Hose-in-Hose Transfer Lines, based on information submitted by the manufacturer and published literature. The effective service life of transfer line assemblies is a function of several factors. Foremost among these are process fluid characteristics, ambient environmental conditions, and the manufacturer's stated shelf life. This evaluation examines the manufacturer's certification of shelf life, the manufacturer's certifications of chemical compatibility with waste, and published literature on the effects of exposure to ionizing radiation on the mechanical properties of elastomeric materials to evaluate transfer line service life

  9. A versatile system for USER cloning-based assembly of expression vectors for mammalian cell engineering.

    Directory of Open Access Journals (Sweden)

    Anne Mathilde Lund

    Full Text Available A new versatile mammalian vector system for protein production, cell biology analyses, and cell factory engineering was developed. The vector system applies the ligation-free uracil-excision based technique--USER cloning--to rapidly construct mammalian expression vectors of multiple DNA fragments and with maximum flexibility, both for choice of vector backbone and cargo. The vector system includes a set of basic vectors and a toolbox containing a multitude of DNA building blocks including promoters, terminators, selectable marker- and reporter genes, and sequences encoding an internal ribosome entry site, cellular localization signals and epitope- and purification tags. Building blocks in the toolbox can be easily combined as they contain defined and tested Flexible Assembly Sequence Tags, FASTs. USER cloning with FASTs allows rapid swaps of gene, promoter or selection marker in existing plasmids and simple construction of vectors encoding proteins, which are fused to fluorescence-, purification-, localization-, or epitope tags. The mammalian expression vector assembly platform currently allows for the assembly of up to seven fragments in a single cloning step with correct directionality and with a cloning efficiency above 90%. The functionality of basic vectors for FAST assembly was tested and validated by transient expression of fluorescent model proteins in CHO, U-2-OS and HEK293 cell lines. In this test, we included many of the most common vector elements for heterologous gene expression in mammalian cells, in addition the system is fully extendable by other users. The vector system is designed to facilitate high-throughput genome-scale studies of mammalian cells, such as the newly sequenced CHO cell lines, through the ability to rapidly generate high-fidelity assembly of customizable gene expression vectors.

  10. Programmed Nanomaterial Assemblies in Large Scales: Applications of Synthetic and Genetically- Engineered Peptides to Bridge Nano-Assemblies and Macro-Assemblies

    Energy Technology Data Exchange (ETDEWEB)

    Matsui, Hiroshi

    2014-09-09

    Work is reported in these areas: Large-scale & reconfigurable 3D structures of precise nanoparticle assemblies in self-assembled collagen peptide grids; Binary QD-Au NP 3D superlattices assembled with collagen-like peptides and energy transfer between QD and Au NP in 3D peptide frameworks; Catalytic peptides discovered by new hydrogel-based combinatorial phage display approach and their enzyme-mimicking 2D assembly; New autonomous motors of metal-organic frameworks (MOFs) powered by reorganization of self-assembled peptides at interfaces; Biomimetic assembly of proteins into microcapsules on oil-in-water droplets with structural reinforcement via biomolecular recognition-based cross-linking of surface peptides; and Biomimetic fabrication of strong freestanding genetically-engineered collagen peptide films reinforced by quantum dot joints. We gained the broad knowledge about biomimetic material assembly from nanoscale to microscale ranges by coassembling peptides and NPs via biomolecular recognition. We discovered: Genetically-engineered collagen-like peptides can be self-assembled with Au NPs to generate 3D superlattices in large volumes (> μm{sup 3}); The assembly of the 3D peptide-Au NP superstructures is dynamic and the interparticle distance changes with assembly time as the reconfiguration of structure is triggered by pH change; QDs/NPs can be assembled with the peptide frameworks to generate 3D superlattices and these QDs/NPs can be electronically coupled for the efficient energy transfer; The controlled assembly of catalytic peptides mimicking the catalytic pocket of enzymes can catalyze chemical reactions with high selectivity; and, For the bacteria-mimicking swimmer fabrication, peptide-MOF superlattices can power translational and propellant motions by the reconfiguration of peptide assembly at the MOF-liquid interface.

  11. Performance analysis of flow lines with non-linear flow of material

    CERN Document Server

    Helber, Stefan

    1999-01-01

    Flow line design is one of the major tasks in production management. The decision to install a set of machines and buffers is often highly irreversible. It determines both cost and revenue to a large extent. In order to assess the economic impact of any possible flow line design, production rates and inventory levels have to be estimated. These performance measures depend on the allocation of buffers whenever the flow of material is occasionally disrupted, for example due to machine failures or quality problems. The book describes analytical methods that can be used to evaluate flow lines much faster than with simulation techniques. Based on these fast analytical techniques, it is possible to determine a flow line design that maximizes the net present value of the flow line investment. The flow of material through the line may be non-linear, for example due to assembly operations or quality inspections.

  12. Image processor of model-based vision system for assembly robots

    International Nuclear Information System (INIS)

    Moribe, H.; Nakano, M.; Kuno, T.; Hasegawa, J.

    1987-01-01

    A special purpose image preprocessor for the visual system of assembly robots has been developed. The main function unit is composed of lookup tables to utilize the advantage of semiconductor memory for large scale integration, high speed and low price. More than one unit may be operated in parallel since it is designed on the standard IEEE 796 bus. The operation time of the preprocessor in line segment extraction is usually 200 ms per 500 segments, though it differs according to the complexity of scene image. The gray-scale visual system supported by the model-based analysis program using the extracted line segments recognizes partially visible or overlapping industrial workpieces, and detects these locations and orientations

  13. Non-occupational physical activity levels of shift workers compared with non-shift workers

    Science.gov (United States)

    Loef, Bette; Hulsegge, Gerben; Wendel-Vos, G C Wanda; Verschuren, W M Monique; Bakker, Marije F; van der Beek, Allard J; Proper, Karin I

    2017-01-01

    Objectives Lack of physical activity (PA) has been hypothesised as an underlying mechanism in the adverse health effects of shift work. Therefore, our aim was to compare non-occupational PA levels between shift workers and non-shift workers. Furthermore, exposure–response relationships for frequency of night shifts and years of shift work regarding non-occupational PA levels were studied. Methods Data of 5980 non-shift workers and 532 shift workers from the European Prospective Investigation into Cancer and Nutrition-Netherlands (EPIC-NL) were used in these cross-sectional analyses. Time spent (hours/week) in different PA types (walking/cycling/exercise/chores) and intensities (moderate/vigorous) were calculated based on self-reported PA. Furthermore, sports were operationalised as: playing sports (no/yes), individual versus non-individual sports, and non-vigorous-intensity versus vigorous-intensity sports. PA levels were compared between shift workers and non-shift workers using Generalized Estimating Equations and logistic regression. Results Shift workers reported spending more time walking than non-shift workers (B=2.3 (95% CI 1.2 to 3.4)), but shift work was not associated with other PA types and any of the sports activities. Shift workers who worked 1–4 night shifts/month (B=2.4 (95% CI 0.6 to 4.3)) and ≥5 night shifts/month (B=3.7 (95% CI 1.8 to 5.6)) spent more time walking than non-shift workers. No exposure–response relationships were found between years of shift work and PA levels. Conclusions Shift workers spent more time walking than non-shift workers, but we observed no differences in other non-occupational PA levels. To better understand if and how PA plays a role in the negative health consequences of shift work, our findings need to be confirmed in future studies. PMID:27872151

  14. Mortality among retired fur workers. Dyers, dressers (tanners) and service workers

    Energy Technology Data Exchange (ETDEWEB)

    Sweeney, M.H.; Walrath, J.; Waxweiler, R.J.

    1985-08-01

    A retrospective cohort mortality study was conducted on 807 fur dyers, fur dressers (tanners), and fur service workers who were pensioned between 1952 and 1977 by the Fur, Leather and Machine Workers Union of New York City. Workplace exposures of fur workers varied with job category. Dyers were exposed to oxidative dyes used in commercial hair dyes; dressers and service workers were exposed to tanning chemicals. In a comparison with the New York City population, no significant increases in mortality were observed among the fur dyers. Among fur dressers, mortality from all malignant neoplasms and lung cancer was significantly elevated, as was mortality from cardiovascular disease among fur service workers. When examined by ethnic origin, the elevated SMR values and directly age-adjusted rate ratios suggested that foreign-born fur dressers and eastern European-born fur workers experienced the highest risks for lung and colorectal cancers, respectively. These data support previous findings of increased mortality from colorectal cancer in the foreign-born population of the United States and suggest a possible occupational etiology for the observed lung cancer excess.

  15. Assembly of the T-cell antigen receptor. Participation of the CD3 omega chain

    DEFF Research Database (Denmark)

    Neisig, A; Vangsted, A; Zeuthen, J

    1993-01-01

    The human TCR is composed of the Ti alpha beta heterodimer in association with the CD3 chains CD3 gamma delta epsilon zeta 2. Another chain, referred to as CD3 omega, has recently been described in T cells. CD3 omega is an intracellular protein transiently associated with the CD3 complex during...... the assembly of the TCR in the endoplasmic reticulum (ER) and it is not expressed on the cell surface. The function of CD3 omega is unknown but it has been suggested that it plays an important role in the assembly of the TCR. We have studied the possible function of CD3 omega in the human leukemic T-cell line...... Jurkat and different variants of this cell line. Cells were metabolically labeled, subjected to lysis, immunoprecipitated, and analyzed by SDS-PAGE. The results indicate that: 1) CD3 omega associates primarily with the CD3 delta epsilon complex; 2) CD3 omega is not associated with single Ti alpha or Ti...

  16. 75 FR 20382 - Chrysler LLC, St. Louis North Assembly Plant, Including On-Site Leased Workers From HAAS TCM, Inc...

    Science.gov (United States)

    2010-04-19

    ...., Diversified Contract Service, Inc. 639, and Logistics Management Services, Inc., Fenton, MO; Amended... Logistics Management Services, Inc. worked on-site at the Chrysler LLC, Fenton, Missouri plant (Logistics... Department is amending this certification to include workers leased from Logistics Management Services, Inc...

  17. 75 FR 20384 - Chrysler LLC, St. Louis North Assembly Plant, Including On-Site Leased Workers From Haas TCM, Inc...

    Science.gov (United States)

    2010-04-19

    .... Diversified Contract Service, Inc. 639, and Logistics Management Services, Inc. Fenton, MO; Amended... Logistics Management Services, Inc. worked on-site at the Chrysler LLC, Fenton, Missouri plant (Logistics... Department is amending this certification to include workers leased from Logistics Management Services, Inc...

  18. Self-assembly of self-assembled molecular triangles

    Indian Academy of Sciences (India)

    While the solution state structure of 1 can be best described as a trinuclear complex, in the solidstate well-fashioned intermolecular - and CH- interactions are observed. Thus, in the solid-state further self-assembly of already self-assembled molecular triangle is witnessed. The triangular panels are arranged in a linear ...

  19. Evaluation of nine popular de novo assemblers in microbial genome assembly.

    Science.gov (United States)

    Forouzan, Esmaeil; Maleki, Masoumeh Sadat Mousavi; Karkhane, Ali Asghar; Yakhchali, Bagher

    2017-12-01

    Next generation sequencing (NGS) technologies are revolutionizing biology, with Illumina being the most popular NGS platform. Short read assembly is a critical part of most genome studies using NGS. Hence, in this study, the performance of nine well-known assemblers was evaluated in the assembly of seven different microbial genomes. Effect of different read coverage and k-mer parameters on the quality of the assembly were also evaluated on both simulated and actual read datasets. Our results show that the performance of assemblers on real and simulated datasets could be significantly different, mainly because of coverage bias. According to outputs on actual read datasets, for all studied read coverages (of 7×, 25× and 100×), SPAdes and IDBA-UD clearly outperformed other assemblers based on NGA50 and accuracy metrics. Velvet is the most conservative assembler with the lowest NGA50 and error rate. Copyright © 2017. Published by Elsevier B.V.

  20. Occupational Stress Among Home Healthcare Workers: Integrating Worker and Agency-Level Factors.

    Science.gov (United States)

    Zoeckler, Jeanette M

    2018-02-01

    Home healthcare work is physically and emotionally exhausting. In addition, home healthcare workers frequently work under precarious work arrangements for low wages and in poor work conditions. Little is known about how sources of job strain for home healthcare workers might be reduced. This research examines the occupational stressors among paid home care workers by analyzing home healthcare agency characteristics and individual home healthcare workers' experiences in upstate New York agencies (n = 9). The study augments existing theoretical models and describes new sources of stress arising from the nature of agency-based caregiving. Results feature the analysis of both agency executives' (n = 20) and home healthcare workers' narratives (n = 25) to make the agency's inner workings more transparent. Agency structures and culture are implicated in the lack of progress to address home care workers' health problems. Policy change should focus on compensation, healthier work conditions, and training requirements.

  1. Chemical chaperones exceed the chaperone effects of RIC-3 in promoting assembly of functional α7 AChRs.

    Directory of Open Access Journals (Sweden)

    Alexander Kuryatov

    Full Text Available Functional α7 nicotinic acetylcholine receptors (AChRs do not assemble efficiently in cells transfected with α7 subunits unless the cells are also transfected with the chaperone protein RIC-3. Despite the presence of RIC-3, large amounts of these subunits remain improperly assembled. Thus, additional chaperone proteins are probably required for efficient assembly of α7 AChRs. Cholinergic ligands can act as pharmacological chaperones to promote assembly of mature AChRs and upregulate the amount of functional AChRs. In addition, we have found that the chemical chaperones 4-phenylbutyric acid (PBA and valproic acid (VPA greatly increase the amount of functional α7 AChRs produced in a cell line expressing both α7 and RIC-3. Increased α7 AChR expression allows assay of drug action using a membrane potential-sensitive fluorescent indicator. Both PBA and VPA also increase α7 expression in the SH-SY5Y neuroblastoma cell line that endogenously expresses α7 AChRs. VPA increases expression of endogenous α7 AChRs in hippocampal neurons but PBA does not. RIC-3 is insufficient for optimal assembly of α7 AChRs, but provides assay conditions for detecting additional chaperones. Chemical chaperones are a useful pragmatic approach to express high levels of human α7 AChRs for drug selection and characterization and possibly to increase α7 expression in vivo.

  2. A conceptual design of assembly strategy and dedicated tools for assembly of 40o sector

    International Nuclear Information System (INIS)

    Park, H.K.; Nam, K.O.; Kim, D.J.; Ahn, H.J.; Lee, J.H.; Im, K.; Shaw, R.

    2010-01-01

    The International Thermanuclear Experimental Reactor (ITER) tokamak device is composed of 9 vacuum vessel (VV)/toroidal field coils (TFCs)/vacuum vessel thermal shields (VVTS) 40 o sectors. Each VV/TFCs/VVTS 40 o sector is made up of one 40 o VV, two 20 o TFCs and associated VVTS segments. The 40 o sectors are sub-assembled at assembly hall respectively and then nine 40 o sectors sub-assembled at assembly hall are finally assembled at tokamak in-pit hall. The assembly strategy and tools for the 40 o sector sub-assembly and final assembly should be developed to satisfy the basic assembly requirements of the ITER tokamak device. Accordingly, the purpose-built assembly tools should be designed and manufactured considering assembly plan, available space, cost, safety, easy operation, efficient maintenance, and so on. The 40 o sector assembly tools are classified into 2 groups. One group is the sub-assembly tools including upending tool, lifting tool, sub-assembly tool, VV supports and bracing tools used at assembly hall and the other group is the in-pit assembly tools including lifting tool, central column, radial beams and their supports. This paper describes the current status of the assembly strategy and major tools for the VV/TFCs/VVTS 40 o sector assembly at in-pit hall and assembly hall. The conceptual design of the major assembly tools and assembly process at assembly hall and tokamak in-pit hall are presented also.

  3. Advanced worker protection system

    International Nuclear Information System (INIS)

    Caldwell, B.; Duncan, P.; Myers, J.

    1995-01-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D ampersand D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D ampersand D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D ampersand D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project will result in the development of an Advanced Worker Protection System (AWPS). The AWPS will be built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with advanced protective garments, advanced liquid cooling garment, respirator, communications, and support equipment to provide improved worker protection, simplified system maintenance, and dramatically improve worker productivity through longer duration work cycles. Phase I of the project has resulted in a full scale prototype Advanced Worker Protection Ensemble (AWPE, everything the worker will wear), with sub-scale support equipment, suitable for integrated testing and preliminary evaluation. Phase II will culminate in a full scale, certified, pre-production AWPS and a site demonstration

  4. Advanced worker protection system

    Energy Technology Data Exchange (ETDEWEB)

    Caldwell, B.; Duncan, P.; Myers, J.

    1995-12-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project will result in the development of an Advanced Worker Protection System (AWPS). The AWPS will be built around a life support backpack that uses liquid air to provide cooling as well as breathing gas to the worker. The backpack will be combined with advanced protective garments, advanced liquid cooling garment, respirator, communications, and support equipment to provide improved worker protection, simplified system maintenance, and dramatically improve worker productivity through longer duration work cycles. Phase I of the project has resulted in a full scale prototype Advanced Worker Protection Ensemble (AWPE, everything the worker will wear), with sub-scale support equipment, suitable for integrated testing and preliminary evaluation. Phase II will culminate in a full scale, certified, pre-production AWPS and a site demonstration.

  5. The footwear factory's assembly sector: opposing organizational structure and quality from the ergonomic work analysis.

    Science.gov (United States)

    Silva, Kláudia M M N; Coelho, Bernardo G P; Junior, Josemir V S; Faria, Luiz F M; Dutra, Ludmila; Alvarenga, Marília; Roggini, Renan; Echternach, Eliza Helena de Oliveira

    2012-01-01

    Data from 2006 indicated that Brazilian footwear leather industry was composed of approximately 9,488 formally registered establishments, considering the leather industry, footwear and leather goods. It was responsible for 211,582 people employed. However, in spite of having many employees, this kind of organization found several problems when analyzed from the ergonomics view. With this premise, then, in order to identify bottlenecks and other engineering problems that could cause discomfort and motivation lack among workers, leading directly to the loss of the product quality, the assembly sector of women's shoes factory was characterized.

  6. Calculation of Savannah River K Reactor Mark-22 assembly LOCA/ECS power limits

    International Nuclear Information System (INIS)

    Fischer, S.R.; Farman, R.F.; Birdsell, S.A.

    1992-01-01

    This paper summarizes the results of TRAC-PF1/MOD3 calculations of Mark-22 fuel assembly of loss-of-coolant accident/emergency cooling system (LOCA/ECS) power limits for the Savannah River Site (SRS) K Reactor. This effort was part of a larger effort undertaken by the Los Alamos National Laboratory for the US Department of Energy to perform confirmatory power limits calculations for the SRS K Reactor. A method using a detailed three-dimensional (3D) TRAC model of the Mark-22 fuel assembly was developed to compute LOCA/ECS power limits. Assembly power was limited to ensure that no point on the fuel assembly walls would exceed the local saturation temperature. The detailed TRAC model for the Mark-22 assembly consisted of three concentric 3D vessel components which simulated the two targets, two fuel tubes, and three main flow channels of the fuel assembly. The model included 100% eccentricity between the assembly annuli and a 20% power tilt. Eccentricity in the radial alignment of the assembly annuli arises because axial spacer ribs that run the length of the fuel and targets are used. Wall-shear, interfacial-shear, and wall heat-transfer correlations were developed and implemented in TRAC-PF1/MOD3 specifically for modeling flow and heat transfer in the narrow ribbed annuli encountered in the Mark-22 fuel assembly design. We established the validity of these new constitutive models using separate-effects benchmarks. TRAC system calculations of K Reactor indicated that the limiting ECS-phase accident is a double-ended guillonite break in a process water line at the pump discharge (i.e., a PDLOCA). The fuel assembly with the minimum cooling potential is identified from this system calculation. Detailed assembly calculations then were performed using appropriate boundary conditions obtained from this limiting system LOCA. Coolant flow rates and pressure boundary conditions were obtained from this system calculation and applied to the detailed assembly model

  7. The Impact of Western Social Workers in Romania - a Fine Line between Empowerment and Disempowerment

    OpenAIRE

    Dümling, Bianca

    2004-01-01

    Ideally the social work profession promotes social change, problem solving in human relationships and the empowerment and liberation of people to enhance their well-being (IFSW 2004). The social work practice, however, often proves to be different. Social workers are always in the danger to make decisions for their clients or define problems according to their own interpretation and world view. In quite a number of cases, the consequence of such a social work practice is that the clients feel...

  8. Exploring stigma by association among front-line care providers serving sex workers.

    Science.gov (United States)

    Phillips, Rachel; Benoit, Cecilia

    2013-10-01

    Stigma by association, also referred to as "courtesy stigma," involves public disapproval evoked as a consequence of associating with stigmatized persons. While a small number of sociological studies have shown how stigma by association limits the social support and social opportunities available to family members, there is a paucity of research examining this phenomenon among the large network of persons who provide health and social services to stigmatized groups. This paper presents results from a primarily qualitative study of the work-place experiences of a purposive sample of staff from an organization providing services to sex workers. The findings suggest that stigma by association has an impact on staff health because it shapes both the workplace environment as well as staff perceptions of others' support. At the same time, it is evident that some staff, owing to their more advantaged social location, are better able to manage courtesy stigma than others. Copyright © 2013 Longwoods Publishing.

  9. Fuel injection assembly for use in turbine engines and method of assembling same

    Science.gov (United States)

    Berry, Jonathan Dwight; Johnson, Thomas Edward; York, William David; Uhm, Jong Ho

    2015-12-15

    A fuel injection assembly for use in a turbine engine is provided. The fuel injection assembly includes an end cover, an endcap assembly, a fluid supply chamber, and a plurality of tube assemblies positioned at the endcap assembly. Each of the tube assemblies includes housing having a fuel plenum and a cooling fluid plenum. The cooling fluid plenum is positioned downstream from the fuel plenum and separated from the fuel plenum by an intermediate wall. The plurality of tube assemblies also include a plurality of tubes that extends through the housing. Each of the plurality of tubes is coupled in flow communication with the fluid supply chamber and a combustion chamber positioned downstream from the tube assembly. The plurality of tube assemblies further includes an aft plate at a downstream end of the cooling fluid plenum. The plate includes at least one aperture.

  10. AutoAssemblyD: a graphical user interface system for several genome assemblers.

    Science.gov (United States)

    Veras, Adonney Allan de Oliveira; de Sá, Pablo Henrique Caracciolo Gomes; Azevedo, Vasco; Silva, Artur; Ramos, Rommel Thiago Jucá

    2013-01-01

    Next-generation sequencing technologies have increased the amount of biological data generated. Thus, bioinformatics has become important because new methods and algorithms are necessary to manipulate and process such data. However, certain challenges have emerged, such as genome assembly using short reads and high-throughput platforms. In this context, several algorithms have been developed, such as Velvet, Abyss, Euler-SR, Mira, Edna, Maq, SHRiMP, Newbler, ALLPATHS, Bowtie and BWA. However, most such assemblers do not have a graphical interface, which makes their use difficult for users without computing experience given the complexity of the assembler syntax. Thus, to make the operation of such assemblers accessible to users without a computing background, we developed AutoAssemblyD, which is a graphical tool for genome assembly submission and remote management by multiple assemblers through XML templates. AssemblyD is freely available at https://sourceforge.net/projects/autoassemblyd. It requires Sun jdk 6 or higher.

  11. Productivity Gains from Worker Mobility and their Distribution between Workers and Firms

    NARCIS (Netherlands)

    A. Stoyanov (Andrey); N.V. Zubanov (Nick)

    2012-01-01

    textabstractUsing data from the universe of Danish manufacturing firms and workers over the period 1995-2007, we estimate output gains linked to productivity spillovers through worker mobility, and calculate the shares in these gains accrued to firms, to the workers who bring spillovers, and to the

  12. Why healthcare workers are sick of TB

    Directory of Open Access Journals (Sweden)

    Arne von Delft

    2015-03-01

    Full Text Available Dr Thato Mosidi never expected to be diagnosed with tuberculosis (TB, despite widely prevalent exposure and very limited infection control measures. The life-threatening diagnosis of primary extensively drug-resistant TB (XDR-TB came as an even greater shock. The inconvenient truth is that, rather than being protected, Dr Mosidi and thousands of her healthcare colleagues are at an increased risk of TB and especially drug-resistant TB. In this viewpoint paper we debunk the widely held false belief that healthcare workers are somehow immune to TB disease (TB-proof and explore some of the key factors contributing to the pervasive stigmatization and subsequent non-disclosure of occupational TB. Our front-line workers are some of the first to suffer the consequences of a progressively more resistant and fatal TB epidemic, and urgent interventions are needed to ensure the safety and continued availability of these precious healthcare resources. These include the rapid development and scale-up of improved diagnostic and treatment options, strengthened infection control measures, and focused interventions to tackle stigma and discrimination in all its forms. We call our colleagues to action to protect themselves and those they care for.

  13. Balanceamento e rebalanceamento de linhas de montagem operadas por grupos de trabalho autogerenciados Balancing and rebalancing of assembly lines operated by self-managed work groups

    Directory of Open Access Journals (Sweden)

    Flávio César F. Fernandes

    2000-12-01

    Full Text Available Este trabalho analisa detalhadamente o problema de balanceamento / rebalanceamento das linhas de montagem operadas por grupos de trabalho autogerenciados propondo um modelo otimizante de programação inteira que é tratado computacionalmente com êxito por meio da linguagem de modelagem GAMS ("General Algebraic Modeling System" e solver Zoom. Não encontramos na literatura trabalhos que tenham modelado matematicamente, de forma exata ou heurística, tal problema. Para se estimar a eficiência futura da linha, um dos dados que o modelo necessita, propomos o uso de dois métodos utilizados em outras áreas (curva de aprendizagem e previsão de demanda. Mostra-se a diferença entre problema de balanceamento e de rebalanceamento bem como é feita uma revisão bibliográfica complementar a respeito do problema de balanceamento de linhas. Ela complementa a última revisão dos métodos exatos que é de 1986 e a última dos métodos heurísticos que é de 1998.This paper analyses in details the balancing and rebalancing problem of assembly lines operated by self-managed work groups. It proposes an optimizing integer programming model that is treated computationally with success by means of the modeling language GAMS (General Algebraic Modeling System and solver ZOOM. We have not found other works that have presented a heuristic or exact mathematical model for such a problem. For estimating the future line efficiency, one of the parameters that the model requires, we propose the use of two methods used in other areas (learning curve and demand forecasting. Differences between balancing and rebalancing problems are shown and also a complementary bibliographical review about line balancing is accomplished. It complements the last review of exact methods dated on 1986 and the last review of heuristic methods dated on 1998.

  14. Mortality among retired fur workers. Dyers, dressers (tanners) and service workers.

    Science.gov (United States)

    Sweeney, M H; Walrath, J; Waxweiler, R J

    1985-08-01

    A retrospective cohort mortality study was conducted on 807 fur dyers, fur dressers (tanners), and fur service workers who were pensioned between 1952 and 1977 by the Fur, Leather and Machine Workers Union of New York City. Workplace exposures of fur workers varied with job category. Dyers were exposed to oxidative dyes used in commercial hair dyes; dressers and service workers were exposed to tanning chemicals. In a comparison with the New York City population, no significant increases in mortality were observed among the fur dyers. Among fur dressers, mortality from all malignant neoplasms [standardized mortality ratio (SMR) 151] and lung cancer (SMR 232) was significantly elevated, as was mortality from cardiovascular disease (SMR 126) among fur service workers. When examined by ethnic origin, the elevated SMR values and directly age-adjusted rate ratios suggested that foreign-born fur dressers and eastern European-born fur workers experienced the highest risks for lung and colorectal cancers, respectively. These data support previous findings of increased mortality from colorectal cancer in the foreign-born population of the United States and suggest a possible occupational etiology for the observed lung cancer excess.

  15. Non-occupational physical activity levels of shift workers compared with non-shift workers.

    Science.gov (United States)

    Loef, Bette; Hulsegge, Gerben; Wendel-Vos, G C Wanda; Verschuren, W M Monique; Vermeulen, Roel C H; Bakker, Marije F; van der Beek, Allard J; Proper, Karin I

    2017-05-01

    Lack of physical activity (PA) has been hypothesised as an underlying mechanism in the adverse health effects of shift work. Therefore, our aim was to compare non-occupational PA levels between shift workers and non-shift workers. Furthermore, exposure-response relationships for frequency of night shifts and years of shift work regarding non-occupational PA levels were studied. Data of 5980 non-shift workers and 532 shift workers from the European Prospective Investigation into Cancer and Nutrition-Netherlands (EPIC-NL) were used in these cross-sectional analyses. Time spent (hours/week) in different PA types (walking/cycling/exercise/chores) and intensities (moderate/vigorous) were calculated based on self-reported PA. Furthermore, sports were operationalised as: playing sports (no/yes), individual versus non-individual sports, and non-vigorous-intensity versus vigorous-intensity sports. PA levels were compared between shift workers and non-shift workers using Generalized Estimating Equations and logistic regression. Shift workers reported spending more time walking than non-shift workers (B=2.3 (95% CI 1.2 to 3.4)), but shift work was not associated with other PA types and any of the sports activities. Shift workers who worked 1-4 night shifts/month (B=2.4 (95% CI 0.6 to 4.3)) and ≥5 night shifts/month (B=3.7 (95% CI 1.8 to 5.6)) spent more time walking than non-shift workers. No exposure-response relationships were found between years of shift work and PA levels. Shift workers spent more time walking than non-shift workers, but we observed no differences in other non-occupational PA levels. To better understand if and how PA plays a role in the negative health consequences of shift work, our findings need to be confirmed in future studies. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  16. Study on ionizing radiation to the workers' lymphocyte micronucleus rate and chromosome aberrations

    International Nuclear Information System (INIS)

    Li Jianhua; Wang Linchao; He Wei

    2007-01-01

    Objective: To study lymphocyte genetic material of an iron and steel enterprise workers exposed to the ionizing radiation, find out measures to protect their health and reduce ionizing radiation occupation harm. Methods: 342 workers were choseh as the exposed group who worked in an iron and steel enterprise in the beam installment operation, to examine their circumference blood lymphocyte micronucleus rate and the chromosome aberrations, simultaneously select 280 chefs as the control group, The irradiation dosage was determined and statistical analysis was carded out wich the consideration of their length of work and differences in work post. Results: Exposed group: the micronucleus rate masculine gender (MNR), 4 people, the masculine gender pick out rate is 12.87%. The chromosome aberration factor masculine gender (CAF), 12 people, the masculine rate is 3.51%. Control group: MNR 3 people, the asculine gender pick out rate is 1.07%; CAF 2 people, masculine gender rate is 0.72%. Comparing the two groups, every item has the significant difference. Workers in is the exposed group workers have the average exposure dose of 6.73mSv/a, MNR,CAF are illuminated to the dosage have a positive line correlation. They become increased as the job lenght prolongs. The nucleon name, the material calculation and the medical X-radial are responsible for the highest ratio. Conclusion: In iron and steel enterprises, long-time ionizing radiation can cause the workers' circumference blood lymphocyte micronucleus rate and the chromosome aberrations obvious to rise. The beam protection measures strengthened so as to reduce the harms to workers. (authors)

  17. Integrated configurable equipment selection and line balancing for mass production with serial-parallel machining systems

    Science.gov (United States)

    Battaïa, Olga; Dolgui, Alexandre; Guschinsky, Nikolai; Levin, Genrikh

    2014-10-01

    Solving equipment selection and line balancing problems together allows better line configurations to be reached and avoids local optimal solutions. This article considers jointly these two decision problems for mass production lines with serial-parallel workplaces. This study was motivated by the design of production lines based on machines with rotary or mobile tables. Nevertheless, the results are more general and can be applied to assembly and production lines with similar structures. The designers' objectives and the constraints are studied in order to suggest a relevant mathematical model and an efficient optimization approach to solve it. A real case study is used to validate the model and the developed approach.

  18. A Theoretical and Experimental Study of DNA Self-assembly

    Science.gov (United States)

    Chandran, Harish

    The control of matter and phenomena at the nanoscale is fast becoming one of the most important challenges of the 21st century with wide-ranging applications from energy and health care to computing and material science. Conventional top-down approaches to nanotechnology, having served us well for long, are reaching their inherent limitations. Meanwhile, bottom-up methods such as self-assembly are emerging as viable alternatives for nanoscale fabrication and manipulation. A particularly successful bottom up technique is DNA self-assembly where a set of carefully designed DNA strands form a nanoscale object as a consequence of specific, local interactions among the different components, without external direction. The final product of the self-assembly process might be a static nanostructure or a dynamic nanodevice that performs a specific function. Over the past two decades, DNA self-assembly has produced stunning nanoscale objects such as 2D and 3D lattices, polyhedra and addressable arbitrary shaped substrates, and a myriad of nanoscale devices such as molecular tweezers, computational circuits, biosensors and molecular assembly lines. In this dissertation we study multiple problems in the theory, simulations and experiments of DNA self-assembly. We extend the Turing-universal mathematical framework of self-assembly known as the Tile Assembly Model by incorporating randomization during the assembly process. This allows us to reduce the tile complexity of linear assemblies. We develop multiple techniques to build linear assemblies of expected length N using far fewer tile types than previously possible. We abstract the fundamental properties of DNA and develop a biochemical system, which we call meta-DNA, based entirely on strands of DNA as the only component molecule. We further develop various enzyme-free protocols to manipulate meta-DNA systems and provide strand level details along with abstract notations for these mechanisms. We simulate DNA circuits by

  19. Assembly, alignment and test of the Transiting Exoplanet Survey Satellite (TESS) optical assemblies

    Science.gov (United States)

    Balonek, Gregory; Brown, Joshua J.; Andre, James E.; Chesbrough, Christian D.; Chrisp, Michael P.; Dalpiaz, Michael; Lennon, Joseph; Richards, B. C.; Clark, Kristin E.

    2017-08-01

    The Transiting Exoplanet Survey Satellite (TESS) will carry four visible waveband, seven-element, refractive F/1.4 lenses, each with a 34 degree diagonal field of view. This paper describes the methods used for the assembly, alignment and test of the four flight optical assemblies. Prior to commencing the build of the four flight optical assemblies, a Risk Reduction Unit (RRU) was successfully assembled and tested [1]. The lessons learned from the RRU were applied to the build of the flight assemblies. The main modifications to the flight assemblies include the inking of the third lens element stray light mitigation, tighter alignment tolerances, and diamond turning for critical mechanical surfaces. Each of the optical assemblies was tested interferometrically and measured with a low coherence distance measuring interferometer (DMI) to predict the optimal shim thickness between the lens assembly and detector before -75°C environmental testing. In addition to individual test data, environmental test results from prior assemblies allow for the exploration of marginal performance differences between each of the optical assemblies.

  20. Unitizing worker expertise and maximizing the brain reward centers

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, Anthony Bert [Los Alamos National Laboratory

    2010-01-01

    People are experts when it comes to the work they do; unfortunately their expertise is not utilized as frequently as it could be. More opportunities need to be provided that allow people to participate in the design of their work including: accident investigations, job planning, and process improvements. Many employers use some form of job hazard analysis process to identify and document hazards and controls, but the front line worker is rarely involved. This presentation will show the core principles supporting employee involvement, provide examples where workers had brilliant ideas but no one listened, and provide examples where workers were given the opportunity to use their expertise to improve occupational safety. According to Abraham Maslow's Hierarch of Needs model, one essential human need is to be innovative and solve problems. Advances in brain science have proven, through functional magnetic resonance imaging (fMRI) studies, the brain reward pathway is activated when people are recognized for their intellectual contributions. As people contribute their expertise to improve occupational safety more frequently they will feel a sense of gratification. In addition, safety professionals will have more time to spend on strategic planning of emerging occupational safety issues. One effect of the current global recession is that SH&E professionals are asked to do more with less. Therefore, to be successful it is essential that SH&E professionals incorporate worker expertise in job planning. This will be illustrated in the presentation through an example where a worker had the answer to a difficult decision on appropriate personal protective equipment for a job but no one asked the worker for his idea during the job planning phase. Fortunately the worker was eventually consulted and his recommendation for the appropriate personal protective equipment for the job was implemented before work began. The goal of this presentation is to expand the awareness and

  1. SWAP-Assembler: scalable and efficient genome assembly towards thousands of cores.

    Science.gov (United States)

    Meng, Jintao; Wang, Bingqiang; Wei, Yanjie; Feng, Shengzhong; Balaji, Pavan

    2014-01-01

    There is a widening gap between the throughput of massive parallel sequencing machines and the ability to analyze these sequencing data. Traditional assembly methods requiring long execution time and large amount of memory on a single workstation limit their use on these massive data. This paper presents a highly scalable assembler named as SWAP-Assembler for processing massive sequencing data using thousands of cores, where SWAP is an acronym for Small World Asynchronous Parallel model. In the paper, a mathematical description of multi-step bi-directed graph (MSG) is provided to resolve the computational interdependence on merging edges, and a highly scalable computational framework for SWAP is developed to automatically preform the parallel computation of all operations. Graph cleaning and contig extension are also included for generating contigs with high quality. Experimental results show that SWAP-Assembler scales up to 2048 cores on Yanhuang dataset using only 26 minutes, which is better than several other parallel assemblers, such as ABySS, Ray, and PASHA. Results also show that SWAP-Assembler can generate high quality contigs with good N50 size and low error rate, especially it generated the longest N50 contig sizes for Fish and Yanhuang datasets. In this paper, we presented a highly scalable and efficient genome assembly software, SWAP-Assembler. Compared with several other assemblers, it showed very good performance in terms of scalability and contig quality. This software is available at: https://sourceforge.net/projects/swapassembler.

  2. Attrition and Rape Case Characteristics: A Profile and Comparison of Female Sex Workers and Non-Sex Workers.

    Science.gov (United States)

    Lea, Susan J; Callaghan, Lynne; Grafton, Iain; Falcone, M Aurora; Shaw, Steve

    2016-07-01

    The attrition of rape cases from the criminal justice system (CJS) remains high and there is a paucity of research in relation to marginalized groups. Sex workers (SWs) are vulnerable to sexual violence due to the nature of their work. They are also unlikely to report such violence to police for a range of reasons. Two stages of research sought to describe the victim, perpetrator, and offense characteristics of SW rape and to examine the attrition of these cases. All rapes and attempted rapes (N = 1,146) reported to police in a large city in the South West of England over a 21-year period were examined; 67 cases involved SWs. Data were extracted from police files in line with the variables of interest. Secondary analysis of the total number of SW rapes (n = 67) resulted in a profile of these cases. A matched pairs study revealed significant differences in victim, perpetrator, and assault characteristics between SW (n = 62) and non-sex-worker (NSW) samples (n = 62). Although no significant difference was found in terms of attrition from the CJS, SW cases were observed to secure more convictions for rape than NSW cases. The implications of the findings for practice and future research are discussed. © The Author(s) 2015.

  3. Assembly tool design

    International Nuclear Information System (INIS)

    Kanamori, Naokazu; Nakahira, Masataka; Ohkawa, Yoshinao; Tada, Eisuke; Seki, Masahiro

    1996-06-01

    The reactor core of the International Thermonuclear Experimental Reactor (ITER) is assembled with a number of large and asymmetric components within a tight tolerance in order to assure the structural integrity for various loads and to provide the tritium confinement. In addition, the assembly procedure should be compatible with remote operation since the core structures will be activated by 14-MeV neutrons once it starts operation and thus personal access will be prohibited. Accordingly, the assembly procedure and tool design are quite essential and should be designed from the beginning to facilitate remote operation. According to the ITER Design Task Agreement, the Japan Atomic Energy Research Institute (JAERI) has performed design study to develop the assembly procedures and associated tool design for the ITER tokamak assembly. This report describes outlines of the assembly tools and the remaining issues obtained in this design study. (author)

  4. Optimal manpower allocation in aircraft line maintenance (Case in GMF AeroAsia)

    Science.gov (United States)

    Puteri, V. E.; Yuniaristanto, Hisjam, M.

    2017-11-01

    This paper presents a mathematical modeling to find the optimal manpower allocation in an aircraft line maintenance. This research focuses on assigning the number and type of manpower that allocated to each service. This study considers the licenced worker or Aircraft Maintenance Engineer Licence (AMEL) and non licenced worker or Aircraft Maintenance Technician (AMT). In this paper, we also consider the relationship of each station in terms of the possibility to transfer the manpower among them. The optimization model considers the number of manpowers needed for each service and the requirement of AMEL worker. This paper aims to determine the optimal manpower allocation using the mathematical modeling. The objective function of the model is to find the minimum employee expenses. The model was solved using the ILOG CPLEX software. The results show that the manpower allocation can meet the manpower need and the all load can be served.

  5. Drive piston assembly for a valve actuator assembly

    Science.gov (United States)

    Sun, Zongxuan

    2010-02-23

    A drive piston assembly is provided that is operable to selectively open a poppet valve. The drive piston assembly includes a cartridge defining a generally stepped bore. A drive piston is movable within the generally stepped bore and a boost sleeve is coaxially disposed with respect to the drive piston. A main fluid chamber is at least partially defined by the generally stepped bore, drive piston, and boost sleeve. First and second feedback chambers are at least partially defined by the drive piston and each are disposed at opposite ends of the drive piston. At least one of the drive piston and the boost sleeve is sufficiently configured to move within the generally stepped bore in response to fluid pressure within the main fluid chamber to selectively open the poppet valve. A valve actuator assembly and engine are also provided incorporating the disclosed drive piston assembly.

  6. MR-1S Interacts with PET100 and PET117 in Module-Based Assembly of Human Cytochrome c Oxidase

    Directory of Open Access Journals (Sweden)

    Sara Vidoni

    2017-02-01

    Full Text Available The biogenesis of human cytochrome c oxidase (COX is an intricate process in which three mitochondrial DNA (mtDNA-encoded core subunits are assembled in a coordinated way with at least 11 nucleus-encoded subunits. Many chaperones shared between yeast and humans are involved in COX assembly. Here, we have used a MT-CO3 mutant cybrid cell line to define the composition of assembly intermediates and identify new human COX assembly factors. Quantitative mass spectrometry analysis led us to modify the assembly model from a sequential pathway to a module-based process. Each module contains one of the three core subunits, together with different ancillary components, including HIGD1A. By the same analysis, we identified the short isoform of the myofibrillogenesis regulator 1 (MR-1S as a new COX assembly factor, which works with the highly conserved PET100 and PET117 chaperones to assist COX biogenesis in higher eukaryotes.

  7. MR-1S Interacts with PET100 and PET117 in Module-Based Assembly of Human Cytochrome c Oxidase.

    Science.gov (United States)

    Vidoni, Sara; Harbour, Michael E; Guerrero-Castillo, Sergio; Signes, Alba; Ding, Shujing; Fearnley, Ian M; Taylor, Robert W; Tiranti, Valeria; Arnold, Susanne; Fernandez-Vizarra, Erika; Zeviani, Massimo

    2017-02-14

    The biogenesis of human cytochrome c oxidase (COX) is an intricate process in which three mitochondrial DNA (mtDNA)-encoded core subunits are assembled in a coordinated way with at least 11 nucleus-encoded subunits. Many chaperones shared between yeast and humans are involved in COX assembly. Here, we have used a MT-CO3 mutant cybrid cell line to define the composition of assembly intermediates and identify new human COX assembly factors. Quantitative mass spectrometry analysis led us to modify the assembly model from a sequential pathway to a module-based process. Each module contains one of the three core subunits, together with different ancillary components, including HIGD1A. By the same analysis, we identified the short isoform of the myofibrillogenesis regulator 1 (MR-1S) as a new COX assembly factor, which works with the highly conserved PET100 and PET117 chaperones to assist COX biogenesis in higher eukaryotes. Copyright © 2017 Elsevier Inc. All rights reserved.

  8. Morphology evolution of PS-b-PDMS block copolymer and its hierarchical directed self-assembly on block copolymer templates

    DEFF Research Database (Denmark)

    Rasappa, Sozaraj; Schulte, Lars; Borah, Dipu

    2018-01-01

    Cylinder-forming polystyrene-block-polydimethylsiloxane (PS-b-PDMS, 27.2k-b-11.7k, SD39) block copolymer having a total molecular weight of 39 kg mol−1 was exploited to achieve in-plane morphologies of lines, dots and antidots. Brush-free self-assembly of the SD39 on silicon substrates was invest...... substrates provides a simplified method for surface nanopatterning, templated growth of nanomaterials and nanofabrication....... the pattern into the underlying substrate. Directed self-assembly and hierarchical directed self-assembly on block copolymer templates for confinement of dots was successfully demonstrated. The strategy for achieving multiple morphologies using one BCP by mere choice of the annealing solvents on unmodified...

  9. Towards improving workers' health by matching work and workers

    NARCIS (Netherlands)

    Zoer, I.

    2014-01-01

    From an occupational health perspective, the match between work and workers was the central topic in this thesis. The term ‘work’ was used to encompass a combination of physical, mental and psychosocial work demands. The term ‘workers’ represents the resources of workers, in terms of physical,

  10. Replicating centromeric chromatin: Spatial and temporal control of CENP-A assembly

    International Nuclear Information System (INIS)

    Nechemia-Arbely, Yael; Fachinetti, Daniele; Cleveland, Don W.

    2012-01-01

    The centromere is the fundamental unit for insuring chromosome inheritance. This complex region has a distinct type of chromatin in which histone H3 is replaced by a structurally different homologue identified in humans as CENP-A. In metazoans, specific DNA sequences are neither required nor sufficient for centromere identity. Rather, an epigenetic mark comprised of CENP-A containing chromatin is thought to be the major determinant of centromere identity. In this view, CENP-A deposition and chromatin assembly are fundamental processes for the maintenance of centromeric identity across mitotic and meiotic divisions. Several lines of evidence support CENP-A deposition in metazoans occurring at only one time in the cell cycle. Such cell cycle-dependent loading of CENP-A is found in divergent species from human to fission yeast, albeit with differences in the cell cycle point at which CENP-A is assembled. Cell cycle dependent CENP-A deposition requires multiple assembly factors for its deposition and maintenance. This review discusses the regulation of new CENP-A deposition and its relevance to centromere identity and inheritance.

  11. Anomalously high intercombination line ratios in symbiotic stars; extreme Bowen pumping?

    International Nuclear Information System (INIS)

    Kastner, S.O.; Bhatia, A.K.; Feibelman, W.A.

    1989-01-01

    We assemble International Ultraviolet Explorer observations of the ratio of the O III intercombination lines near 1660 A, showing that the observed ratios in symbiotic stars are significantly higher than the theoretically predicted optically thin limit of 2.5. The presence of an enhancing physical process is thereby indicated. It is suggested that Bowen pumping of the lower level of the 1666.2 A line in an 'external saturation' limit, coupled with appreciable optical depth, could logically explain the high ratios. Some tentative evidence for this is presented and the relevance of far-infrared observations of the O III 51.8 and 88.3 μm lines in symbiotic sources is emphasized. (author)

  12. A Versatile System for USER Cloning-Based Assembly of Expression Vectors for Mammalian Cell Engineering

    DEFF Research Database (Denmark)

    Lund, Anne Mathilde; Kildegaard, Helene Faustrup; Petersen, Maja Borup Kjær

    2014-01-01

    , in addition the system is fully extendable by other users. The vector system is designed to facilitate high-throughput genome-scale studies of mammalian cells, such as the newly sequenced CHO cell lines, through the ability to rapidly generate high-fidelity assembly of customizable gene expression vectors....

  13. A Dynamic Combinatorial Approach for Identifying Side Groups that Stabilize DNA-Templated Supramolecular Self-Assemblies

    Directory of Open Access Journals (Sweden)

    Delphine Paolantoni

    2015-02-01

    Full Text Available DNA-templated self-assembly is an emerging strategy for generating functional supramolecular systems, which requires the identification of potent multi-point binding ligands. In this line, we recently showed that bis-functionalized guanidinium compounds can interact with ssDNA and generate a supramolecular complex through the recognition of the phosphodiester backbone of DNA. In order to probe the importance of secondary interactions and to identify side groups that stabilize these DNA-templated self-assemblies, we report herein the implementation of a dynamic combinatorial approach. We used an in situ fragment assembly process based on reductive amination and tested various side groups, including amino acids. The results reveal that aromatic and cationic side groups participate in secondary supramolecular interactions that stabilize the complexes formed with ssDNA.

  14. Studies of leukemia and thyroid disease among Chernobyl clean-up workers from the Baltics

    International Nuclear Information System (INIS)

    Inskip, P.D.; Tekkel, M.; Rahu, M.

    1997-01-01

    Following the reactor accident at Chernobyl in late April of 1986, hundreds of thousands of men from throughout the former Soviet Union were sent to Chernobyl to entomb the damaged reactor, remove radioactive debris, and help decontaminate the local environment. They remained for an average of three months and were allowed to accumulate up to 25 cGy of radiation before being sent home. Doses for some workers may have exceeded the allowable limit. The experience of Chernobyl clean-up workers is potentially informative about cancer risk associated with protracted exposure to low levels of radiation. Cohorts of clean-up workers from the Baltic Republics were assembled for study, based on military records and other lists. The study population includes 4,833 men from Estonia 5,709 from Latvia and at least 5,446 from Lithuania, where a pilot study is underway. They are being monitored for cancer incidence through linkages with the corresponding national cancer registries. Biodosimetric assays, including fluorescent in situ hybridization (FISH) for chromosome translocation analysis and the glycophorin A (GPA) somatic cell mutation assay, are being used to supplement information about radiation doses from worker records and questionnaires. Thyroid screening examinations, including palpation, ultrasound and, selectively, fine-needle aspiration biopsies were performed on nearly 2,000 workers in the Estonian cohort (mean age, 40 y) during the spring of 1995, nine years after the reactor accident. The study is still in progress. Work began first in Estonia, and results presented here pertain to this subgroup except as otherwise noted. The average age at the time of arrival at Chernobyl was 31 years. 62% were sent in 1986. Possible reasons for the apparent absence or rarity of radiation-induced thyroid nodules include low and protracted doses, low susceptibility among men exposed as adults, and insufficient passage of time since the accident

  15. SN 1987A gamma-ray line profiles and fluxes

    International Nuclear Information System (INIS)

    Bussard, R.W.; Burrows, A.; The, L.S.

    1989-01-01

    Results for the time dependence of the line profiles and integrated fluxes for the 0.847 and 1.238 MeV gamma rays from the decay of cobalt to excited states of iron are presented for several models of the ejectum of SN 1987A. The relatively early detection of these lines has led several workers to propose that some degree of mixing has brought the cobalt closer to the electron-scattering photosphere than standard models predict. Constraints on the amount of mixing from recent observations are discussed using calculations of the energy-integrated line fluxes as a function of time since the explosion. Implications for the line profiles at various times are considered, and it is found that they show strong time dependences and are quite sensitive to the degree of mixing. The two primary effects are Doppler broadening due to the presence of radioactive material at higher velocities and a strong blueshift at early times resulting from optical depth effects. These results have important implications for gamma-ray observations, especially with high-resolution germanium instruments. Finally, the consequences of the fragmentation of the debris for the early emergence of the gamma-ray lines are considered. 32 refs

  16. Final design of the neutral beam lines for the Tokamak Fusion Test Reactor

    International Nuclear Information System (INIS)

    Pittenger, L.C.; Valby, L.E.; Stone, R.R.; Pedrotti, L.R.; Denhoy, B.; Yoard, R.

    1979-01-01

    Final design of the neutral beam lines for TFTR has been completed. A prototype has been assembled at Lawrence Berkeley Laboratory and is undergoing testing as part of the Neutral Beam System Test Facility (NBSTF). The final neutral beam line (NBL) configuration differs in several details from that previously reported upon; certain components have been added; and testing of the cryopump system has led to some design simplification. It is these developments which are reported herein

  17. Self-assembled nanostructures

    CERN Document Server

    Zhang, Jin Z; Liu, Jun; Chen, Shaowei; Liu, Gang-yu

    2003-01-01

    Nanostructures refer to materials that have relevant dimensions on the nanometer length scales and reside in the mesoscopic regime between isolated atoms and molecules in bulk matter. These materials have unique physical properties that are distinctly different from bulk materials. Self-Assembled Nanostructures provides systematic coverage of basic nanomaterials science including materials assembly and synthesis, characterization, and application. Suitable for both beginners and experts, it balances the chemistry aspects of nanomaterials with physical principles. It also highlights nanomaterial-based architectures including assembled or self-assembled systems. Filled with in-depth discussion of important applications of nano-architectures as well as potential applications ranging from physical to chemical and biological systems, Self-Assembled Nanostructures is the essential reference or text for scientists involved with nanostructures.

  18. Using real-time problem solving to eliminate central line infections.

    Science.gov (United States)

    Shannon, Richard P; Frndak, Diane; Grunden, Naida; Lloyd, Jon C; Herbert, Cheryl; Patel, Bhavin; Cummins, Daniel; Shannon, Alexander H; O'Neill, Paul H; Spear, Steven J

    2006-09-01

    An estimated 200,000 Americans suffer central line-associated bloodstream infections (CLABs) each year, with 15%-20% mortality. Two intensive care units (ICUs) redefined the processes of care through system redesign to deliver reliable outcomes free of the variations that created the breeding ground for infection. The ICUs, comprising 28 beds at Allegheny General Hospital, employed the principles of the Toyota Production System adapted to health care--Perfecting Patient Care--and applied them to central line placement and maintenance. Intensive observations, which revealed multiple variances from established practices, and root cause analyses of all CLABs empowered the workers to implement countermeasures designed to eliminate the defects in the processes of central line placement and maintenance. New processes were implemented within 90 days. Within a year CLABs decreased from 49 to 6 (10.5 to 1.2 infections/1,000 line-days), and mortalities from 19 to 1 (51% to 16%), despite an increase in the use of central lines and number of line-days. These results were sustained during a 34-month period. CLABs are not an inevitable product of complex ICU care but the result of highly variable and therefore unreliable care delivery that predisposes to infection.

  19. [Analysis on occupational noise-induced hearing loss of different type workers in underground mining].

    Science.gov (United States)

    Liu, Q C; Duo, C H; Wang, Z; Yan, K; Zhang, J; Xiong, W; Zhu, M

    2017-11-20

    Objective: To investigate hearing loss status of blasters, drillers mechanics and so on in underground mining, and put forward suggestion diagnosis of occupational explosive deafness and occupational deafness. Methods: Underground excavation workers in a metal mine were recruited in this study, those with a history of ear disease and non-occupational deafness were all excluded. Finally, the features of pure tone audiometry of 459 noise-exposed workers were analyzed. Results: High-frequency hearing loss occurred on 351workers and the positive detection rate was 74.29%, workers who had both high-frequency and linguistic frequency hearing loss were 51 and the positive detection rate was 11.11%. The positive detection of high-frequency hearing loss in right ear (χ(2)=9.427 and P = 0.024) and in left ear (χ(2)=14.375, P =0.002) was significantly different between different exposure age groups. The positive detection of high-frequency hearing loss of driving group was the highest, followed by blasting group, mining group and machine repair group. The characteristics of the hearing loss caused by drilling noise of the blasting workers with no accident occurred were in line with that of noise-induced hearing loss. Conclusion: The diagnosis grading should be carried out according to the diagnostic criteria of occupational noise-induced deafness for the employees who engaged in the blasting operation with no record of blast accident.

  20. [Relationship between perceptions of safety climate at workplace and depressive disorders in manufacturing workers].

    Science.gov (United States)

    Liu, Xu-hua; Xiao, Ya-ni; Huang, Zhi-xiong; Huang, Shao-bin; Cao, Xiao-ou; Guan, Dong-bo; Chen, Wei-qing

    2013-04-01

    To investigate the risk factors for depressive disorders in manufacturing workers and to provide a basis for developing health promotion measures at workplace. A questionnaire survey was performed in 8085 front-line production workers from 33 manufacturing enterprises in Nanhai District of Foshan, Guangdong Province, China. The questionnaire contained a survey of demographic characteristics, the Safety Climate Scale, the Center for Epidemiological Studies Depression Scale, etc. The multilevel logistic regression analysis was applied to investigate the risk factors for depressive disorders in workers. A total of 6260 workers completed the survey; their mean age was 31.1 ± 8.6 years, and 53.2% of them were males. The multilevel logistic regression analysis showed that after adjustment for sociodemographic factors such as age, sex, and martial status, more depressive disorders were reported in the enterprises with higher score of "production safety training" than in those with lower score (OR = 1.46, 95%CI = 1.07 ∼ 1.97); fewer depressive disorders were reported in the enterprises with higher score of "colleagues concerned about production safety" than in those with lower score (OR = 0.08, 95%CI = 0.03 ∼ 0.26); the relationships of "safety warnings and precautions" and "managers concerned about production safety" with workers' depressive disorders were not statistically significant (OR = 0.78, 95%CI = 0.48 ∼ 1.28; OR = 1.08, 95%CI = 0.68 ∼ 1.72). Depressive disorders in manufacturing workers are related to the safety climate at workplace, which indicates that a good safety climate at workplace should be created to prevent and control depressive disorders in workers.

  1. Cognitive Reflection and the Diligent Worker: An Experimental Study of Millennials

    OpenAIRE

    Corgnet, Brice; Hern?n Gonzalez, Roberto; Mateo, Ricardo

    2015-01-01

    Recent studies have shown that despite crucially needing the creative talent of millennials (people born after 1980) organizations have been reluctant to hire young workers because of their supposed lack of diligence. We propose to help resolve this dilemma by studying the determinants of task performance and shirking behaviors of millennials in a laboratory work environment. We find that cognitive ability is a good predictor of task performance in line with previous literature. In contrast w...

  2. Eryptosis in lead-exposed workers

    International Nuclear Information System (INIS)

    Aguilar-Dorado, Itzel-Citlalli; Hernández, Gerardo; Quintanar-Escorza, Martha-Angelica; Maldonado-Vega, María; Rosas-Flores, Margarita; Calderón-Salinas, José-Víctor

    2014-01-01

    Eryptosis is a physiological phenomenon in which old and damaged erythrocytes are removed from circulation. Erythrocytes incubated with lead have exhibited major eryptosis. In the present work we found evidence of high levels of eryptosis in lead exposed workers possibly via oxidation. Blood samples were taken from 40 male workers exposed to lead (mean blood lead concentration 64.8 μg/dl) and non-exposed workers (4.2 μg/dl). The exposure to lead produced an intoxication characterized by 88.3% less δ-aminolevulinic acid dehydratase (δALAD) activity in lead exposed workers with respect to non-lead exposed workers. An increment of oxidation in lead exposed workers was characterized by 2.4 times higher thiobarbituric acid-reactive substance (TBARS) concentration and 32.8% lower reduced/oxidized glutathione (GSH/GSSG) ratio. Oxidative stress in erythrocytes of lead exposed workers is expressed in 192% higher free calcium concentration [Ca 2+ ] i and 1.6 times higher μ-calpain activity with respect to non-lead exposed workers. The adenosine triphosphate (ATP) concentration was not significantly different between the two worker groups. No externalization of phosphatidylserine (PS) was found in non-lead exposed workers (< 0.1%), but lead exposed workers showed 2.82% externalization. Lead intoxication induces eryptosis possibly through a molecular pathway that includes oxidation, depletion of reduced glutathione (GSH), increment of [Ca 2+ ], μ-calpain activation and externalization of PS in erythrocytes. Identifying molecular signals that induce eryptosis in lead intoxication is necessary to understand its physiopathology and chronic complications. - Graphical abstract: Fig. 1. (A) Blood lead concentration (PbB) and (B) phosphatidylserine externalization on erythrocyte membranes of non-lead exposed (□) and lead exposed workers (■). Values are mean ± SD. *Significantly different (P < 0.001). - Highlights: • Erythrocytes of lead exposed workers showed higher PS

  3. Eryptosis in lead-exposed workers

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar-Dorado, Itzel-Citlalli [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Hernández, Gerardo [Section of Methodology of Science, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Quintanar-Escorza, Martha-Angelica [Faculty of Medicine, UJED, Durango, DGO (Mexico); Maldonado-Vega, María [CIATEC, León, GTO (Mexico); Rosas-Flores, Margarita [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico); Calderón-Salinas, José-Víctor, E-mail: jcalder@cinvestav.mx [Biochemistry Department, Centro de Investigación y Estudios Avanzados IPN, México, DF (Mexico)

    2014-12-01

    Eryptosis is a physiological phenomenon in which old and damaged erythrocytes are removed from circulation. Erythrocytes incubated with lead have exhibited major eryptosis. In the present work we found evidence of high levels of eryptosis in lead exposed workers possibly via oxidation. Blood samples were taken from 40 male workers exposed to lead (mean blood lead concentration 64.8 μg/dl) and non-exposed workers (4.2 μg/dl). The exposure to lead produced an intoxication characterized by 88.3% less δ-aminolevulinic acid dehydratase (δALAD) activity in lead exposed workers with respect to non-lead exposed workers. An increment of oxidation in lead exposed workers was characterized by 2.4 times higher thiobarbituric acid-reactive substance (TBARS) concentration and 32.8% lower reduced/oxidized glutathione (GSH/GSSG) ratio. Oxidative stress in erythrocytes of lead exposed workers is expressed in 192% higher free calcium concentration [Ca{sup 2+}]{sub i} and 1.6 times higher μ-calpain activity with respect to non-lead exposed workers. The adenosine triphosphate (ATP) concentration was not significantly different between the two worker groups. No externalization of phosphatidylserine (PS) was found in non-lead exposed workers (< 0.1%), but lead exposed workers showed 2.82% externalization. Lead intoxication induces eryptosis possibly through a molecular pathway that includes oxidation, depletion of reduced glutathione (GSH), increment of [Ca{sup 2+}], μ-calpain activation and externalization of PS in erythrocytes. Identifying molecular signals that induce eryptosis in lead intoxication is necessary to understand its physiopathology and chronic complications. - Graphical abstract: Fig. 1. (A) Blood lead concentration (PbB) and (B) phosphatidylserine externalization on erythrocyte membranes of non-lead exposed (□) and lead exposed workers (■). Values are mean ± SD. *Significantly different (P < 0.001). - Highlights: • Erythrocytes of lead exposed workers

  4. Self-assembly of heterogeneous supramolecular structures with uniaxial anisotropy.

    Science.gov (United States)

    Ruiz-Osés, M; Gonzalez-Lakunza, N; Silanes, I; Gourdon, A; Arnau, A; Ortega, J E

    2006-12-28

    Uniaxial anisotropy in two-dimensional self-assembled supramolecular structures is achieved by the coadsorption of two different linear molecules with complementary amine and imide functionalization. The two-dimensional monolayer is defined by a one-dimensional stack of binary chains, which can be forced to line up along steps in vicinal surfaces. The competing driving forces in the self-organization process are discussed in light of the structures observed during single molecule adsorption and coadsorption on flat and vicinal surfaces and the corresponding theoretical calculations.

  5. Control of extracellular matrix assembly by syndecan-2 proteoglycan

    DEFF Research Database (Denmark)

    Klass, C M; Couchman, J R; Woods, A

    2000-01-01

    Extracellular matrix (ECM) deposition and organization is maintained by transmembrane signaling and integrins play major roles. We now show that a second transmembrane component, syndecan-2 heparan sulfate proteoglycan, is pivotal in matrix assembly. Chinese Hamster Ovary (CHO) cells were stably...... to rearrange laminin or fibronectin substrates into fibrils and to bind exogenous fibronectin. Transfection of activated alphaIIbalphaLdeltabeta3 integrin into alpha(5)-deficient CHO B2 cells resulted in reestablishment of the previously lost fibronectin matrix. However, cotransfection of this cell line with S...

  6. Inner/Outer nuclear membrane fusion in nuclear pore assembly: biochemical demonstration and molecular analysis.

    Science.gov (United States)

    Fichtman, Boris; Ramos, Corinne; Rasala, Beth; Harel, Amnon; Forbes, Douglass J

    2010-12-01

    Nuclear pore complexes (NPCs) are large proteinaceous channels embedded in double nuclear membranes, which carry out nucleocytoplasmic exchange. The mechanism of nuclear pore assembly involves a unique challenge, as it requires creation of a long-lived membrane-lined channel connecting the inner and outer nuclear membranes. This stabilized membrane channel has little evolutionary precedent. Here we mapped inner/outer nuclear membrane fusion in NPC assembly biochemically by using novel assembly intermediates and membrane fusion inhibitors. Incubation of a Xenopus in vitro nuclear assembly system at 14°C revealed an early pore intermediate where nucleoporin subunits POM121 and the Nup107-160 complex were organized in a punctate pattern on the inner nuclear membrane. With time, this intermediate progressed to diffusion channel formation and finally to complete nuclear pore assembly. Correct channel formation was blocked by the hemifusion inhibitor lysophosphatidylcholine (LPC), but not if a complementary-shaped lipid, oleic acid (OA), was simultaneously added, as determined with a novel fluorescent dextran-quenching assay. Importantly, recruitment of the bulk of FG nucleoporins, characteristic of mature nuclear pores, was not observed before diffusion channel formation and was prevented by LPC or OA, but not by LPC+OA. These results map the crucial inner/outer nuclear membrane fusion event of NPC assembly downstream of POM121/Nup107-160 complex interaction and upstream or at the time of FG nucleoporin recruitment.

  7. Coal worker's pneumoconiosis

    Science.gov (United States)

    ... this page: //medlineplus.gov/ency/article/000130.htm Coal worker's pneumoconiosis To use the sharing features on this page, please enable JavaScript. Coal worker's pneumoconiosis (CWP) is a lung disease that ...

  8. Value Preferences of Social Workers.

    Science.gov (United States)

    Tartakovsky, Eugene; Walsh, Sophie D

    2018-04-01

    The current study examines value preferences of social workers in Israel. Using a theoretical framework of person-environment fit paradigm and theory of values, the study compared social workers (N = 641, mean age = 37.7 years, 91 percent female) with a representative sample of Israeli Jews (N = 1,600, mean age = 44.2, 52 percent female). Questionnaires included personal value preferences and sociodemographic variables (gender, age, education, religiosity, and immigrant status). Multivariate analysis of covariance showed that value preferences of social workers differed significantly from those of the general population. Analyses of covariance showed that social workers reported a higher preference for self-transcendence and a lower preference for conservation and self-enhancement values. Results have significance for the selection, training, and supervision of social workers. They suggest that it is important to assess to what extent selection processes for social workers are primarily recruiting social workers with shared values, thus creating an overly homogenous population of social workers. An understanding of personal value motivations can help social workers in their own process of self-development and growth, and to understand how the profession can fulfill their basic motivations.

  9. Deacetylation of H4-K16Ac and heterochromatin assembly in senescence

    Directory of Open Access Journals (Sweden)

    Contrepois Kévin

    2012-08-01

    Full Text Available Abstract Background Cellular senescence is a stress response of mammalian cells leading to a durable arrest of cell proliferation that has been implicated in tumor suppression, wound healing, and aging. The proliferative arrest is mediated by transcriptional repression of genes essential for cell division by the retinoblastoma protein family. This repression is accompanied by varying degrees of heterochromatin assembly, but little is known regarding the molecular mechanisms involved. Results We found that both deacetylation of H4-K16Ac and expression of HMGA1/2 can contribute to DNA compaction during senescence. SIRT2, an NAD-dependent class III histone deacetylase, contributes to H4-K16Ac deacetylation and DNA compaction in human fibroblast cell lines that assemble striking senescence-associated heterochromatin foci (SAHFs. Decreased H4-K16Ac was observed in both replicative and oncogene-induced senescence of these cells. In contrast, this mechanism was inoperative in a fibroblast cell line that did not assemble extensive heterochromatin during senescence. Treatment of senescent cells with trichostatin A, a class I/II histone deacetylase inhibitor, also induced rapid and reversible decondensation of SAHFs. Inhibition of DNA compaction did not significantly affect the stability of the senescent state. Conclusions Variable DNA compaction observed during senescence is explained in part by cell-type specific regulation of H4 deacetylation and HMGA1/2 expression. Deacetylation of H4-K16Ac during senescence may explain reported decreases in this mark during mammalian aging and in cancer cells.

  10. Self-Assembly of Flux-Closure Polygons from Magnetite Nanocubes.

    Science.gov (United States)

    Szyndler, Megan W; Corn, Robert M

    2012-09-06

    Well-defined nanoscale flux-closure polygons (nanogons) have been fabricated on hydrophilic surfaces from the face-to-face self-assembly of magnetite nanocubes. Uniform ferrimagnetic magnetite nanocubes (∼86 nm) were synthesized and characterized with a combination of electron microscopy, diffraction, and magnetization measurements. The nanocubes were subsequently cast onto hydrophilic substrates, wherein the cubes lined up face-to-face and formed a variety of polygons due to magnetostatic and hydrophobic interactions. The generated surfaces consist primarily of three- and four-sided nanogons; polygons ranging from two to six sides were also observed. Further examination of the nanogons showed that the constraints of the face-to-face assembly of nanocubes often led to bowed sides, strained cube geometries, and mismatches at the acute angle vertices. Additionally, extra nanocubes were often present at the vertices, suggesting the presence of external magnetostatic fields at the polygon corners. These nanogons are inimitable nanoscale magnetic structures with potential applications in the areas of magnetic memory storage and high-frequency magnetics.

  11. The characteristics of activities of the operator of a management system by the line for release of foodstuff

    Directory of Open Access Journals (Sweden)

    Al-Hetari H.M. Abdulaziz

    2016-01-01

    Full Text Available The article presents the analysis of the main stages of professional activity of the operator of a management system by a production line of food products. Studied the question of the serious consequences of human error as the cause of the marriage in the manufacture of food products on automated lines. The nature of the error automated systems operators as a result of the deterioration of psychophysical state of the working person. The importance of modeling the signal generating emergency alarm, can significantly reduce the probability of release of potentially dangerous products. The optimality of the psychophysical state of the control system operator line of food production is highlighted as one of the main criteria for the rational organization of work. The problem of assessing changes in the human condition is also studied, participating in professional activities. The classification of types of functional states control over employee -depending on its purpose. Special attention in work is paid to an example of change of a psychophysical state, expressed in exhaustion of the worker of production. It gives a detailed description of the external signs of exhaustion in the comparative analysis of manual and mental work. The article shows the main tariff and qualification characteristics of activities of operators of lines in production of food products depending on their categories are specified. Describes a group of workers, depending on the operator's activity, indicating the brief description of each group. Based on the analysis of tariff and qualifying characteristics of lines of the operators in the production of food products of different categories, it shows that the range of qualifying categories covers almost al l groups of workers with the exception of the head of the operator. Highlight the desired differentiated approach to the assessment of psychophysiological state operators.

  12. Healthy worker survivor analysis in an occupational cohort study of Dutch agricultural workers

    NARCIS (Netherlands)

    Spierenburg, E. A. J.; Smit, L. A. M.; Heederik, D.; Robbe, P.; Hylkema, M. N.; Wouters, I. M.

    High microbial exposures in farmers and agricultural workers are associated with less atopy. Although it has been speculated that healthy worker survival could be an explanation, this has not been studied so far. Therefore, we investigated the presence of healthy worker survival in a five-year

  13. Factors Associated with Fatal Occupational Accidents among Mexican Workers: A National Analysis

    Science.gov (United States)

    Gonzalez-Delgado, Mery; Gómez-Dantés, Héctor; Fernández-Niño, Julián Alfredo; Robles, Eduardo; Borja, Víctor H.; Aguilar, Miriam

    2015-01-01

    Objective To identify the factors associated with fatal occupational injuries in Mexico in 2012 among workers affiliated with the Mexican Social Security Institute. Methods Analysis of secondary data using information from the National Occupational Risk Information System, with the consequence of the occupational injury (fatal versus non-fatal) as the response variable. The analysis included 406,222 non-fatal and 1,140 fatal injuries from 2012. The factors associated with the lethality of the injury were identified using a logistic regression model with the Firth approach. Results Being male (OR=5.86; CI95%: 4.22-8.14), age (OR=1.04; CI95%: 1.03-1.06), employed in the position for 1 to 10 years (versus less than 1 year) (OR=1.37; CI95%: 1.15-1.63), working as a facilities or machine operator or assembler (OR: 3.28; CI95%: 2.12- 5.07) and being a worker without qualifications (OR=1.96; CI95%: 1.18-3.24) (versus an office worker) were associated with fatality in the event of an injury. Additionally, companies classified as maximum risk (OR=1.90; CI 95%: 1.38-2.62), workplace conditions (OR=7.15; CI95%: 3.63-14.10) and factors related to the work environment (OR=9.18; CI95%:4.36-19.33) were identified as risk factors for fatality in the event of an occupational injury. Conclusions Fatality in the event of an occupational injury is associated with factors related to sociodemographics (age, sex and occupation), the work environment and workplace conditions. Worker protection policies should be created for groups with a higher risk of fatal occupational injuries in Mexico. PMID:25790063

  14. Anatomicopathological basis and clinical diagnostic significance of Kerley's A line

    International Nuclear Information System (INIS)

    Wang Zhenguang; Ma Daqing; Chen Budong; He Wen; Wang Xinlian; Guan Yansheng; Zhang Yansong

    2007-01-01

    Objective: To study anatomic and pathological basis of Kerley's A line, and to evaluate the role of Kerley's A line in differential diagnosis of diffuse lung diseases (DLD). Methods: HRCT scans, gross specimen section(50-100 μm thickness) and histologic section(5-8 μm thickness) were performed and analyzed comparatively on 28 dry lung specimens from the patients with coal worker's pneumoconiosis and occupational exposure history to coal dusts. At the same time, HRCT images of 176 patients with DLD were retrospectively reviewed for the detection of Kerley's A line. Results: Kerley's A lines were seen in 17 of 28 lung specimens on coronal HRCT images. The anatomic basis of Kerley's A line represented the continuity of two or more thickened interlobular septa (14 eases) and incomplete fibrotic septa between segments or subsegments (3 cases). Histologically, the linear opacities represented the deposits of coal dust, fibrosis, edema, inflammation, thickened vessel wall within interlobular septa. Kerley's A lines were present in 11 of 176 patients (6.3%) including interstitial pulmonary edema (5 cases), viral pneumonia (2 cases), lymphangitic carcinomatosis (2 cases), sarcoidosis (1 cases) and pulmonary alveolar proteinosis (1 cases). Conclusion: Kerley's A line has a limited usefulness in the differential diagnosis of DLD because it is seen infrequently and not discermable. (authors)

  15. Newnes electronics assembly handbook

    CERN Document Server

    Brindley, Keith

    2013-01-01

    Newnes Electronics Assembly Handbook: Techniques, Standards and Quality Assurance focuses on the aspects of electronic assembling. The handbook first looks at the printed circuit board (PCB). Base materials, basic mechanical properties, cleaning of assemblies, design, and PCB manufacturing processes are then explained. The text also discusses surface mounted assemblies and packaging of electromechanical assemblies, as well as the soldering process. Requirements for the soldering process; solderability and protective coatings; cleaning of PCBs; and mass solder/component reflow soldering are des

  16. Evaluation of Hose in Hose Transfer Line Service Life for Hanford's Interim Stabilization Program

    Energy Technology Data Exchange (ETDEWEB)

    TORRES, T.D.

    2000-08-24

    RPP-6153, Engineering Task Plan for Hose-in-Hose Transfer System for the Interim Stabilization Program, defines the programmatic goals, functional requirements, and technical criteria for the development and subsequent installation of transfer line equipment to support Hanford's Interim Stabilization Program. RPP-6028, Specification for Hose in Hose Transfer Lines for Hanford's Interim Stabilization Program, has been issued to define the specific requirements for the design, manufacture, and verification of transfer line assemblies for specific waste transfer applications. Included in RPP-6028 are tables defining the chemical constituents of concern to which transfer lines will be exposed. Current Interim Stabilization Program planning forecasts that the at-grade transfer lines will be required to convey pumpable waste for as much as three years after commissioning. Prudent engineering dictates that the equipment placed in service have a working life in excess of this forecasted time period, with some margin to allow for future adjustments to the planned schedule. This document evaluates the effective service life of the Hose-in-Hose Transfer Lines, based on information submitted by the manufacturer and published literature. The effective service life of transfer line assemblies is a function of several factors. Foremost among these are process fluid characteristics, ambient environmental conditions, and the manufacturer's stated shelf life. This evaluation examines the manufacturer's certification of shelf life, the manufacturer's certifications of chemical compatibility with waste, and published literature on the effects of exposure to ionizing radiation on the mechanical properties of elastomeric materials to evaluate transfer line service life.

  17. Doxycycline hinders phenylalanine fibril assemblies revealing a potential novel therapeutic approach in phenylketonuria.

    Science.gov (United States)

    De Luigi, Ada; Mariani, Alessandro; De Paola, Massimiliano; Re Depaolini, Andrea; Colombo, Laura; Russo, Luca; Rondelli, Valeria; Brocca, Paola; Adler-Abramovich, Lihi; Gazit, Ehud; Del Favero, Elena; Cantù, Laura; Salmona, Mario

    2015-10-29

    A new paradigm for the aetiopathology of phenylketonuria suggests the presence of amyloid-like assemblies in the brains of transgenic mouse models and patients with phenylketonuria, possibly shedding light on the selective cognitive deficit associated with this disease. Paralleling the amyloidogenic route that identifies different stages of peptide aggregation, corresponding to different levels of toxicity, we experimentally address for the first time, the physico-chemical properties of phenylalanine aggregates via Small Angle, Wide Angle X-ray Scattering and Atomic Force Microscopy. Results are consistent with the presence of well-structured, aligned fibres generated by milliMolar concentrations of phenylalanine. Moreover, the amyloid-modulating doxycycline agent affects the local structure of phenylalanine aggregates, preventing the formation of well-ordered crystalline structures. Phenylalanine assemblies prove toxic in vitro to immortalized cell lines and primary neuronal cells. Furthermore, these assemblies also cause dendritic sprouting alterations and synaptic protein impairment in neurons. Doxycycline counteracts these toxic effects, suggesting an approach for the development of future innovative non-dietary preventive therapies.

  18. Effect of motivational group interviewing-based safety education on Workers' safety behaviors in glass manufacturing.

    Science.gov (United States)

    Navidian, Ali; Rostami, Zahra; Rozbehani, Nasrin

    2015-09-19

    Worker safety education using models that identify and reinforce factors affecting behavior is essential. The present study aimed to determine the effect of safety education based on motivational interviewing on awareness of, attitudes toward, and engagement in worker safety in the glass production industry in Hamedan, Iran, in 2014. This was a quasi-experimental interventional study including a total of 70 production line workers at glass production facilities in Hamedan. The workers were randomly assigned to either an intervention or a control group, with 35 workers in each group. Participants in the control group received four one-hour safety education sessions, in the form of traditional lectures. Those in the intervention group received four educational sessions based on motivational group interviewing, which were conducted in four groups of eight to ten participants each. The instruments used included a researcher-developed questionnaire with checklists addressing safety awareness, and attitude and performance, which were completed before and 12 weeks after the intervention. The data were analyzed using descriptive statistics, independent and paired t-tests, and chi-squared tests. Having obtained the differences in scores before and after the intervention, we determined mean changes in the scores of awareness, attitude, and use of personal protective equipment among workers who underwent motivational group interviewing (3.74 ± 2.16, 1.71 ± 3.16, and 3.2 ± 1.92, respectively, p work environment.

  19. Eryptosis in lead-exposed workers.

    Science.gov (United States)

    Aguilar-Dorado, Itzel-Citlalli; Hernández, Gerardo; Quintanar-Escorza, Martha-Angelica; Maldonado-Vega, María; Rosas-Flores, Margarita; Calderón-Salinas, José-Víctor

    2014-12-01

    Eryptosis is a physiological phenomenon in which old and damaged erythrocytes are removed from circulation. Erythrocytes incubated with lead have exhibited major eryptosis. In the present work we found evidence of high levels of eryptosis in lead exposed workers possibly via oxidation. Blood samples were taken from 40 male workers exposed to lead (mean blood lead concentration 64.8μg/dl) and non-exposed workers (4.2μg/dl). The exposure to lead produced an intoxication characterized by 88.3% less δ-aminolevulinic acid dehydratase (δALAD) activity in lead exposed workers with respect to non-lead exposed workers. An increment of oxidation in lead exposed workers was characterized by 2.4 times higher thiobarbituric acid-reactive substance (TBARS) concentration and 32.8% lower reduced/oxidized glutathione (GSH/GSSG) ratio. Oxidative stress in erythrocytes of lead exposed workers is expressed in 192% higher free calcium concentration [Ca(2+)]i and 1.6 times higher μ-calpain activity with respect to non-lead exposed workers. The adenosine triphosphate (ATP) concentration was not significantly different between the two worker groups. No externalization of phosphatidylserine (PS) was found in non-lead exposed workers (lead exposed workers showed 2.82% externalization. Lead intoxication induces eryptosis possibly through a molecular pathway that includes oxidation, depletion of reduced glutathione (GSH), increment of [Ca(2+)], μ-calpain activation and externalization of PS in erythrocytes. Identifying molecular signals that induce eryptosis in lead intoxication is necessary to understand its physiopathology and chronic complications. Copyright © 2014 Elsevier Inc. All rights reserved.

  20. The Assembly of the LHC Short Straight Sections (SSS) at CERN Project Status and Lessons Learned

    CERN Document Server

    Parma, Vittorio; Dos Santos de Campos, Paulo M; Feitor, Rogerio C; Gandel, Makcim; López, R; Schmidlkofer, Martin; Slits, Ivo

    2005-01-01

    The series production of the LHC SSS has started in the beginning of 2004 and is foreseen to last until end 2006. The production consists in the assembly of 474 cold masses housing superconducting quadrupoles and corrector magnets within their cryostats. 87 cold mass variants, resulting from various combinations of main quadrupole and corrector magnets, have to be assembled in 55 cryostat types, depending on the specific cryogenic and electrical powering schemes required by the collider topology. The assembly activity features the execution of more than 5 km of leak-tight welding of stainless steel and aluminium cryogenic lines, designed for 20-bar pressure, according to high qualification standards and undergoing severe QA inspections. Some 2500 leak detection tests, using He mass spectrometry, are required to check the tightness of the cryogenic circuits. Extensive electrical control work, to check the integrity of the magnet instrumentation and electrical circuits throughout the assembly of the SSS, is als...

  1. Local high precision 3D measurement based on line laser measuring instrument

    Science.gov (United States)

    Zhang, Renwei; Liu, Wei; Lu, Yongkang; Zhang, Yang; Ma, Jianwei; Jia, Zhenyuan

    2018-03-01

    In order to realize the precision machining and assembly of the parts, the geometrical dimensions of the surface of the local assembly surfaces need to be strictly guaranteed. In this paper, a local high-precision three-dimensional measurement method based on line laser measuring instrument is proposed to achieve a high degree of accuracy of the three-dimensional reconstruction of the surface. Aiming at the problem of two-dimensional line laser measuring instrument which lacks one-dimensional high-precision information, a local three-dimensional profile measuring system based on an accurate single-axis controller is proposed. First of all, a three-dimensional data compensation method based on spatial multi-angle line laser measuring instrument is proposed to achieve the high-precision measurement of the default axis. Through the pretreatment of the 3D point cloud information, the measurement points can be restored accurately. Finally, the target spherical surface is needed to make local three-dimensional scanning measurements for accuracy verification. The experimental results show that this scheme can get the local three-dimensional information of the target quickly and accurately, and achieves the purpose of gaining the information and compensating the error for laser scanner information, and improves the local measurement accuracy.

  2. Office home care workers' occupational health: associations with workplace flexibility and worker insecurity.

    Science.gov (United States)

    Zeytinoglu, Isik U; Denton, Margaret; Davies, Sharon; Plenderleith, Jennifer Millen

    2009-05-01

    Office home care workers provide support to visiting staff, although their work tends to be invisible in many respects. This paper focuses on managers, supervisors, coor dinators, case managers and office administrative staff in home care. We examine the effects of workplace flexibility and worker insecurity on office home care workers' occupational health, particularly their self-reported stress and musculoskeletal disorders. Data come from our survey of 300 home care office staff in a mid-sized city in Ontario. Results show that workers' perceptions of insecurity are positively associated with musculoskeletal disorders but not workplace flexibility measures. We recommend that managers and other decision-makers in the home care field pay attention to the perceptions of workers' insecurity in initiating workplace flexibility measures.

  3. ANALISIS GERAK ROBOT LINE TRACER DENGAN PROGRAM ARTIFICIAL INTELLEGENCE MENGGUNAKAN MICROCONTROLLER AT89S51

    OpenAIRE

    I Wayan Widhiada

    2012-01-01

    The research discussed about the work system of The Line Tracer Robot movement analysis, with using the AI program and assembler programming language. The tools that used are microcontroller type AT89S51, Meitan ASM 2005 Standard Edition version 1.00 as development tools and Meitan 2005 as the hardware tools modul. From the result of research, it can be known that The Line Tracer Robot with AI program is able to show differences, among the white as a based colour and black as a line colour. T...

  4. Lung cancer risk among workers in the construction industry: results from two case-control studies in Montreal.

    Science.gov (United States)

    Lacourt, Aude; Pintos, Javier; Lavoué, Jérôme; Richardson, Lesley; Siemiatycki, Jack

    2015-09-22

    Given the large number of workers in the construction industry, it is important to derive accurate and valid estimates of cancer risk, and in particular lung cancer risk. In most previous studies, risks among construction workers were compared with general populations including blue and white collar workers. The main objectives of this study were to assess whether construction workers experience excess lung cancer risk, and whether exposure to selected construction industry exposures carries excess risks. We wished to address these objectives within the sub-population of blue collar workers. Two case-control studies were conducted in Montreal. Combined, they included 1593 lung cancer cases and 1427 controls, of whom 1304 cases and 1081 controls had been blue collar workers. Detailed lifetime job histories were obtained and translated by experts into histories of exposure to chemical agents. The two key analyses were to estimate odds ratio (OR) estimates of lung cancer risk: a) for all blue-collar construction workers compared with other blue-collar workers, and b) for construction workers exposed to each of 20 exposure agents found in the construction industry compared with construction workers unexposed to those agents. All analyses were conducted using unconditional logistic regression adjusted for socio-demographic factors and smoking history. The OR for all construction workers combined was 1.11 (95 % CI: 0.90-1.38), based on 381 blue collar construction workers. Analyses of specific exposures were hampered by small numbers and imprecise estimates. While none of 20 occupational agents examined was significantly associated with lung cancer, the following agents manifested non-significantly elevated ORs: asbestos, silica, Portland cement, soil dust, calcium oxide and calcium sulfate. Compared with other blue collar workers, there was only a slight increased risk of lung cancer for subjects who ever held an occupation in the construction industry. The analyses of

  5. A characteristic of design solutions for flask moulding lines

    OpenAIRE

    Fedoryszyn, A.

    2007-01-01

    Moulding machines used in manufacture of moulds from synthetic bentonite sands constitute basic equipment of mechanised stands, work centres, and production lines. In the present article, a short characteristic of this equipment was given, basing on the generally accepted criteria of classification taking into consideration novel design solutions and principles of cooperation between individual sub-assemblies. Moulding equipment offered by domestic producers was described with emphasis put on...

  6. Fuel Assembly Damping Summary

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Kanghee; Kang, Heungseok; Oh, Dongseok; Yoon, Kyungho; Kim, Hyungkyu; Kim, Jaeyong [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2013-10-15

    This paper summary the fuel assembly damping data in air/in still water/under flow, released from foreign fuel vendors, compared our data with the published data. Some technical issues in fuel assembly damping measurement testing are also briefly discussed. Understanding of each fuel assembly damping mechanisms according to the surrounding medium and flow velocity can support the fuel design improvement in fuel assembly dynamics and structural integrity aspect. Because the upgraded requirements of the newly-developed advanced reactor system will demands to minimize fuel design margin in integrity evaluation, reduction in conservatism of fuel assembly damping can contribute to alleviate the fuel design margin for sure. Damping is an energy dissipation mechanism in a vibrating mechanical structure and prevents a resonant structure from having infinite vibration amplitudes. The sources of fuel assembly damping are various from support friction to flow contribution, and it can be increased by the viscosity or drag of surrounding fluid medium or the average velocity of water flowing. Fuel licensing requires fuel design evaluation in transient or accidental condition. Dynamic response analysis of fuel assembly is to show fuel integrity and requires information on assembly-wise damping in dry condition and under wet or water flowing condition. However, damping measurement test for the full-scale fuel assembly prototype is not easy to carry out because of the scale (fuel prototype, test facility), unsteadiness of test data (scattering, random sampling and processing), instrumentation under water flowing (water-proof response measurement), and noise. LWR fuel technology division in KAERI is preparing the infra structure for damping measurement test of full-scale fuel assembly, to support fuel industries and related research activities. Here is a preliminary summary of fuel assembly damping, published in the literature. Some technical issues in fuel assembly damping

  7. The prevalence of musculoskeletal problems and risk factors among women assembly workers in the semiconductor industry.

    Science.gov (United States)

    Chandrasakaran, A; Chee, H L; Rampal, K G; Tan, G L

    2003-12-01

    A cross-sectional study to determine work-related musculoskeletal problems and ergonomic risk factors was conducted among 529 women semiconductor workers. Overall, 83.4% had musculoskeletal symptoms in the last one year. Pain in the back (57.8%), lower leg (48.4%) and shoulder (44.8%) were the three most common musculoskeletal problems. Significant associations were found between prolonged standing and upper and lower leg pain, between prolonged sitting and neck and shoulder pain and between prolonged bending and shoulder arm, back and upper leg pain. The study therefore showed a clear association between work-related musculoskeletal pain and prolonged hours spent in particular postures and movements.

  8. A primer for workers' compensation.

    Science.gov (United States)

    Bible, Jesse E; Spengler, Dan M; Mir, Hassan R

    2014-07-01

    A physician's role within a workers' compensation injury extends far beyond just evaluation and treatment with several socioeconomic and psychological factors at play compared with similar injuries occurring outside of the workplace. Although workers' compensation statutes vary among states, all have several basic features with the overall goal of returning the injured worker to maximal function in the shortest time period, with the least residual disability and shortest time away from work. To help physicians unfamiliar with the workers' compensation process accomplish these goals. Review. Educational review. The streamlined review addresses the topics of why is workers' compensation necessary; what does workers' compensation cover; progression after work injury; impairment and maximum medical improvement, including how to use the sixth edition of American Medical Association's (AMA) Guides to the evaluation of permanent impairment (Guides); completion of work injury claim after impairment rating; independent medical evaluation; and causation. In the "no-fault" workers' compensation system, physicians play a key role in progressing the claim along and, more importantly, getting the injured worker back to work as soon as safely possible. Physicians should remain familiar with the workers' compensation process, along with how to properly use the AMA Guides. Copyright © 2014 Elsevier Inc. All rights reserved.

  9. Dewetting-mediated pattern formation in nanoparticle assemblies

    International Nuclear Information System (INIS)

    Stannard, Andrew

    2011-01-01

    The deposition of nanoparticles from solution onto solid substrates is a diverse subfield of current nanoscience research. Complex physical and chemical processes underpin the self-assembly and self-organization of colloidal nanoparticles at two-phase (solid-liquid, liquid-air) interfaces and three-phase (solid-liquid-air) contact lines. This review discusses key recent advances made in the understanding of nonequilibrium dewetting processes of nanoparticle-containing solutions, detailing how such an apparently simple experimental system can give rise to such a strikingly varied palette of two-dimensional self-organized nanoparticle array morphologies. Patterns discussed include worm-like domains, cellular networks, microscale rings, and fractal-like fingering structures. There remain many unresolved issues regarding the role of the solvent dewetting dynamics in assembly processes of this type, with a significant focus on how dewetting can be coerced to produce nanoparticle arrays with desirable characteristics such as long-range order. In addition to these topics, methods developed to control nanofluid dewetting through routes such as confining the geometries of drying solutions, depositing onto pre-patterned heterogeneous substrates, and post-dewetting pattern evolution via local or global manipulation are covered. (topical review)

  10. Dewetting-mediated pattern formation in nanoparticle assemblies.

    Science.gov (United States)

    Stannard, Andrew

    2011-03-02

    The deposition of nanoparticles from solution onto solid substrates is a diverse subfield of current nanoscience research. Complex physical and chemical processes underpin the self-assembly and self-organization of colloidal nanoparticles at two-phase (solid-liquid, liquid-air) interfaces and three-phase (solid-liquid-air) contact lines. This review discusses key recent advances made in the understanding of nonequilibrium dewetting processes of nanoparticle-containing solutions, detailing how such an apparently simple experimental system can give rise to such a strikingly varied palette of two-dimensional self-organized nanoparticle array morphologies. Patterns discussed include worm-like domains, cellular networks, microscale rings, and fractal-like fingering structures. There remain many unresolved issues regarding the role of the solvent dewetting dynamics in assembly processes of this type, with a significant focus on how dewetting can be coerced to produce nanoparticle arrays with desirable characteristics such as long-range order. In addition to these topics, methods developed to control nanofluid dewetting through routes such as confining the geometries of drying solutions, depositing onto pre-patterned heterogeneous substrates, and post-dewetting pattern evolution via local or global manipulation are covered.

  11. The safety of women health workers at the frontlines.

    Science.gov (United States)

    Dasgupta, Jashodhara; Velankar, Jayashree; Borah, Pritisha; Nath, Gangotri Hazarika

    2017-01-01

    This article, based on the report of the fact-finding team on the gang rape and death of an accredited social health activist (ASHA) in Muzaffarnagar in January 2016, attempts to analyse the issues of the safety and mobility of front-line women health workers. It argues that although the National Health Mission is often alluded to as a flagship programme of the government, it has failed in its basic responsibility as an ethical employer, since there is no support and back-up system that can be easily accessed by ASHAs in terms of dealing with the fallout of their social role as "change agents" in rural areas, and community reactions to their mobility and public exposure. The report stresses the need to consider the deeply patriarchal system within which ASHAs function in states such as Uttar Pradesh. It also discusses the fact that the workforce is increasingly shifting from the formal to the informal sector, which has given rise to an assumption that the employer is no longer accountable for women workers' safety at the workplace.

  12. Fuel assembly

    International Nuclear Information System (INIS)

    Abe, Hideaki; Sakai, Takao; Ishida, Tomio; Yokota, Norikatsu.

    1992-01-01

    The lower ends of a plurality of plate-like shape memory alloys are secured at the periphery of the upper inside of the handling head of a fuel assembly. As the shape memory alloy, a Cu-Zn alloy, a Ti-Pd alloy or a Fe-Ni alloy is used. When high temperature coolants flow out to the handling head, the shape memory alloy deforms by warping to the outer side more greatly toward the upper portion thereof with the temperature increase of the coolants. As the result, the shape of the flow channel of the coolants is changed so as to enlarge at the exit of the upper end of the fuel assembly. Then, the pressure loss of the coolants in the fuel assembly is decreased by the enlargement. Accordingly, the flow rate of the coolants in the fuel assembly is increased to lower the temperature of the coolants. Further, high temperature coolants and low temperature coolants are mixed sufficiently just above the fuel assembly. This can suppress the temperature fluctuation of the mixed coolants in the upper portion of the reactor core, thereby enabling to decrease a fatigue and failures of the structural components in the upper portion of the reactor core. (I.N.)

  13. A test of a 2 Tesla superconducting transmission line magnet system

    International Nuclear Information System (INIS)

    Piekarz, Henryk; Carcagno, Ruben; Claypool, Brad; Foster, George W.; Hays, Steven L.; Huang, Yuenian; Kashikhin, Vladimir; Malamud, Ernest; Mazur, Peter O.; Nehring, Roger; Oleck, Andrew; Rabehl, Roger; Schlabach, Phil; Sylvester, Cosmore; Velev, Gueorgui; Volk, James; Wake, Masayoshi

    2005-01-01

    Superconducting transmission line magnet test system for an injector accelerator of a staged VLHC proton-proton colliding beam accelerator has been built and operated at Fermilab. The 1.5 m long, twin-aperture, combined function dipole magnet of 2 Tesla field is excited by a single turn 100 kA transmission line superconductor. The 100 kA dc current is generated using dc-dc switching converters powered by a bulk 240 kW supply. A pair of horizontally placed conventional leads facilitates transfer of this current to the magnet transmission line superconductor operating at liquid helium temperature. Fabrication of magnet components and magnet assembly work are described. The magnet test system and its operation are presented, and the performance is summarized

  14. A test of a 2 Tesla superconducting transmission line magnet system

    Energy Technology Data Exchange (ETDEWEB)

    Piekarz, Henryk; Carcagno, Ruben; Claypool, Brad; Foster, George W.; Hays, Steven L.; Huang, Yuenian; Kashikhin, Vladimir; Malamud, Ernest; Mazur, Peter O.; Nehring,; Oleck, Andrew; Rabehl, Roger; Schlabach, Phil; Sylvester, Cosmore; Velev, Gueorgui; Volk, James; /Fermilab; Wake, Masayoshi; /KEK, Tsukuba

    2005-09-01

    Superconducting transmission line magnet test system for an injector accelerator of a staged VLHC proton-proton colliding beam accelerator has been built and operated at Fermilab. The 1.5 m long, twin-aperture, combined function dipole magnet of 2 Tesla field is excited by a single turn 100 kA transmission line superconductor. The 100 kA dc current is generated using dc-dc switching converters powered by a bulk 240 kW supply. A pair of horizontally placed conventional leads facilitates transfer of this current to the magnet transmission line superconductor operating at liquid helium temperature. Fabrication of magnet components and magnet assembly work are described. The magnet test system and its operation are presented, and the performance is summarized.

  15. Soldering in electronics assembly

    CERN Document Server

    Judd, Mike

    2013-01-01

    Soldering in Electronics Assembly discusses several concerns in soldering of electronic assemblies. The book is comprised of nine chapters that tackle different areas in electronic assembly soldering. Chapter 1 discusses the soldering process itself, while Chapter 2 covers the electronic assemblies. Chapter 3 talks about solders and Chapter 4 deals with flux. The text also tackles the CS and SC soldering process. The cleaning of soldered assemblies, solder quality, and standards and specifications are also discussed. The book will be of great use to professionals who deal with electronic assem

  16. A low redox potential affects monoclonal antibody assembly and glycosylation in cell culture.

    Science.gov (United States)

    Dionne, Benjamin; Mishra, Neha; Butler, Michael

    2017-03-20

    Glycosylation and intracellular assembly of monoclonal antibodies (MAbs) is important for glycan profile consistency. To better understand how these factors may be influenced by a lower redox potential, an IgG1-producing NS0 cell line was grown in the presence of varying concentrations of dithiothreitol (DTT). Cultures were monitored for growth and culture redox potential (CRP) with glycan heterogeneity determined using a HILIC-HPLC method. Macroheterogeneity was unchanged in all conditions whereas the Galactosylation Index (GI) decreased by as much as 50% in cultures with lower CRP or higher dithiothreitol levels. This shift in GI is reflected in more agalactosylated and asialylated species being produced. The MAb assembly pathway was determined using radioactive isotope 35 S incorporated into nascent IgG1 molecules. The assembly pathway for this IgG1 was shown to progress via HC→HC 2 →HC 2 LC→HC 2 LC 2 in all conditions tested and autoradiographs highlighted that the ratio of heavy chain dimer to heavy chain monomer increased over time with increasing DTT concentrations. This increase and correspondingly lower GI values may be due to disruption of the disulfide bonds at higher levels of assembly. A change in the assembly pathway may alter the final IgG glycan pattern and lead to control mechanisms that influence glycan profiles of MAbs. Copyright © 2017. Published by Elsevier B.V.

  17. Healing or harming? Healthcare provider interactions with injured workers and insurers in workers' compensation systems.

    Science.gov (United States)

    Kilgour, Elizabeth; Kosny, Agnieszka; McKenzie, Donna; Collie, Alex

    2015-03-01

    Healthcare providers (HCPs) are influential in the injured worker's recovery process and fulfil many roles in the delivery of health services. Interactions between HCPs and insurers can also affect injured workers' engagement in rehabilitation and subsequently their recovery and return to work. Consideration of the injured workers' perceptions and experiences as consumers of medical and compensation services can provide vital information about the quality, efficacy and impact of such systems. The aim of this systematic review was to identify and synthesize published qualitative research that focused on the interactions between injured workers, HCPs and insurers in workers' compensation systems in order to identify processes or interactions which impact injured worker recovery. A search of six electronic databases for literature published between 1985 and 2012 revealed 1,006 articles. Screening for relevance identified 27 studies which were assessed for quality against set criteria. A final 13 articles of medium and high quality were retained for data extraction. Findings were synthesized using a meta-ethnographic approach. Injured workers reported that HCPs could play both healing and harming roles in their recovery. Supportive patient-centred interaction with HCPs is important for injured workers. Difficult interactions between HCPs and insurers were highlighted in themes of adversarial relations and organisational pressures. Insurer and compensation system processes exerted an influence on the therapeutic relationship. Recommendations to improve relationships included streamlining administrative demands and increasing education and communication between the parties. Injured workers with long term complex injuries experience difficulties with healthcare in the workers' compensation context. Changes in insurer administrative demands and compensation processes could increase HCP participation and job satisfaction. This in turn may improve injured worker recovery

  18. 75 FR 60066 - Limitations of Duty- and Quota-Free Imports of Apparel Articles Assembled in Beneficiary ATPDEA...

    Science.gov (United States)

    2010-09-29

    ... set of Harmonized System lines listed in the Annex to the World Trade Organization Agreement on... COMMITTEE FOR THE IMPLEMENTATION OF TEXTILE AGREEMENTS Limitations of Duty- and Quota-Free Imports of Apparel Articles Assembled in Beneficiary ATPDEA Countries From Regional Country Fabric AGENCY...

  19. Multivalent protein assembly using monovalent self-assembling building blocks

    NARCIS (Netherlands)

    Petkau - Milroy, K.; Sonntag, M.H.; Colditz, A.; Brunsveld, L.

    2013-01-01

    Discotic molecules, which self-assemble in water into columnar supramolecular polymers, emerged as an alternative platform for the organization of proteins. Here, a monovalent discotic decorated with one single biotin was synthesized to study the self-assembling multivalency of this system in regard

  20. Bearing assemblies, apparatuses, and motor assemblies using the same

    Science.gov (United States)

    Sexton, Timothy N.; Cooley, Craig H.; Knuteson, Cody W.

    2015-12-29

    Various embodiments of the invention relate to bearing assemblies, apparatuses and motor assemblies that include geometric features configured to impart a selected amount of heat transfer and/or hydrodynamic film formation. In an embodiment, a bearing assembly may include a plurality of superhard bearing pads distributed circumferentially about an axis. At least some of the plurality of superhard bearing pads may include a plurality of sub-superhard bearing elements defining a bearing surface. At least some of the plurality of sub-superhard bearing elements may be spaced from one another by one or more voids to impart a selected amount of heat transfer and hydrodynamic film formation thereon during operation. The bearing assembly may also include a support ring that carries the plurality of superhard bearing pads. In addition, at least a portion of the sub-superhard bearing elements may extend beyond the support ring.

  1. Identification of a novel rhabdovirus in Spodoptera frugiperda cell lines.

    Science.gov (United States)

    Ma, Hailun; Galvin, Teresa A; Glasner, Dustin R; Shaheduzzaman, Syed; Khan, Arifa S

    2014-06-01

    The Sf9 cell line, derived from Spodoptera frugiperda, is used as a cell substrate for biological products, and no viruses have been reported in this cell line after extensive testing. We used degenerate PCR assays and massively parallel sequencing (MPS) to identify a novel RNA virus belonging to the order Mononegavirales in Sf9 cells. Sequence analysis of the assembled virus genome showed the presence of five open reading frames (ORFs) corresponding to the genes for the N, P, M, G, and L proteins in other rhabdoviruses and an unknown ORF of 111 amino acids located between the G- and L-protein genes. BLAST searches indicated that the S. frugiperda rhabdovirus (Sf-rhabdovirus) was related in a limited region of the L-protein gene to Taastrup virus, a newly discovered member of the Mononegavirales from a leafhopper (Hemiptera), and also to plant rhabdoviruses, particularly in the genus Cytorhabdovirus. Phylogenetic analysis of sequences in the L-protein gene indicated that Sf-rhabdovirus is a novel virus that branched with Taastrup virus. Rhabdovirus morphology was confirmed by transmission electron microscopy of filtered supernatant samples from Sf9 cells. Infectivity studies indicated potential transient infection by Sf-rhabdovirus in other insect cell lines, but there was no evidence of entry or virus replication in human cell lines. Sf-rhabdovirus sequences were also found in the Sf21 parental cell line of Sf9 cells but not in other insect cell lines, such as BT1-TN-5B1-4 (Tn5; High Five) cells and Schneider's Drosophila line 2 [D.Mel.(2); SL2] cells, indicating a species-specific infection. The results indicate that conventional methods may be complemented by state-of-the-art technologies with extensive bioinformatics analysis for identification of novel viruses. The Spodoptera frugiperda Sf9 cell line is used as a cell substrate for the development and manufacture of biological products. Extensive testing has not previously identified any viruses in this cell

  2. Fuel assembly

    International Nuclear Information System (INIS)

    Gjertsen, R.K.; Bassler, E.A.; Huckestein, E.A.; Salton, R.B.; Tower, S.N.

    1988-01-01

    A fuel assembly adapted for use with a pressurized water nuclear reactor having capabilities for fluid moderator spectral shift control is described comprising: parallel arranged elongated nuclear fuel elements; means for providing for axial support of the fuel elements and for arranging the fuel elements in a spaced array; thimbles interspersed among the fuel elements adapted for insertion of a rod control cluster therewithin; means for structurally joining the fuel elements and the guide thimbles; fluid moderator control means for providing a volume of low neutron absorbing fluid within the fuel assembly and for removing a substantially equivalent volume of reactor coolant water therefrom, a first flow manifold at one end of the fuel assembly sealingly connected to a first end of the moderator control tubes whereby the first ends are commonly flow connected; and a second flow manifold, having an inlet passage and an outlet passage therein, sealingly connected to a second end of the moderator control tubes at a second end of the fuel assembly

  3. Self assembly of organic nanostructures and dielectrophoretic assembly of inorganic nanowires.

    Science.gov (United States)

    Dholakia, Geetha; Kuo, Steven; Allen, E. L.

    2007-03-01

    Self assembly techniques enable the organization of organic molecules into nanostructures. Currently engineering strategies for efficient assembly and routine integration of inorganic nanoscale objects into functional devices is very limited. AC Dielectrophoresis is an efficient technique to manipulate inorganic nanomaterials into higher dimensional structures. We used an alumina template based sol-gel synthesis method for the growth of various metal oxide nanowires with typical diameters of 100-150 nm, ranging in length from 3-10 μm. Here we report the dielectrophoretic assembly of TiO2 nanowires, an important material for photocatalysis and photovoltaics, onto interdigitated devices. Self assembly in organic nanostructures and its dependence on structure and stereochemistry of the molecule and dielectrophoretic field dependence in the assembly of inorganic nanowires will be compared and contrasted. Tunneling spectroscopy and DOS of these nanoscale systems will also be discussed.

  4. Linewidth statistics of single InGaAs quantum dot photolumincescence lines

    DEFF Research Database (Denmark)

    Leosson, Kristjan; Jensen, Jacob Riis; Hvam, Jørn Märcher

    2000-01-01

    We have used photoluminescence spectroscopy with high spatial and spectral resolution to measure the linewidths of single emission lines from In0.5Ga0.5As/GaAs self-assembled quantum dots. At 10 K, we find a broad, asymmetric distribution of linewidths with a maximum at 50 mu eV. The distribution......-dot luminescence lines depends only weakly on temperature up to 50 K, showing a broadening of 0.4 mu eV/K. Above 50 K, a thermally activated behavior of the linewidth is observed. This temperature dependence is consistent with the discrete energy level structure of the dots....

  5. [Indian workers in Oman].

    Science.gov (United States)

    Longuenesse, E

    1985-01-01

    Until recently Oman was a country of emigration, but by 1980 an estimated 200,000 foreign workers were in the country due to the petroleum boom. Almost 1/3 of the estimated 300,000 Indian workers in the Gulf states were in Oman, a country whose colonial heritage was closely tied to that of India and many of whose inhabitants still speak Urdu. The number of work permits granted to Indians working in the private sector in Oman increased from 47,928 in 1976 to 80,787 in 1980. An estimated 110,000 Indians were working in Oman in 1982, the great majority in the construction and public works sector. A few hundred Indian women were employed by the government of Oman, as domestics, or in other capacities. No accurate data is available on the qualifications of Indian workers in Oman, but a 1979 survey suggested a relatively low illiteracy rate among them. 60-75% of Indians in Oman are from the state of Kerala, followed by workers from the Punjab and the southern states of Tamil Nadu and Andhra Pradesh and Bombay. Indian workers are recruited by specialized agencies or by friends or relatives already employed in Oman. Employers in Oman prefer to recruit through agencies because the preselection process minimizes hiring of workers unqualified for their posts. Officially, expenses of transportation, visas, and other needs are shared by the worker and the employer, but the demand for jobs is so strong that the workers are obliged to pay commissions which amount to considerable sums for stable and well paying jobs. Wages in Oman are however 2 to 5 times the level in India. Numerous abuses have been reported in recruitment practices and in failure of employers in Oman to pay the promised wages, but Indian workers have little recourse. At the same level of qualifications, Indians are paid less then non-Omani Arabs, who in turn receive less than Oman nationals. Indians who remain in Oman long enough nevertheless are able to support families at home and to accumulate considerable

  6. Fire resistant PV shingle assembly

    Science.gov (United States)

    Lenox, Carl J.

    2012-10-02

    A fire resistant PV shingle assembly includes a PV assembly, including PV body, a fire shield and a connection member connecting the fire shield below the PV body, and a support and inter-engagement assembly. The support and inter-engagement assembly is mounted to the PV assembly and comprises a vertical support element, supporting the PV assembly above a support surface, an upper interlock element, positioned towards the upper PV edge, and a lower interlock element, positioned towards the lower PV edge. The upper interlock element of one PV shingle assembly is inter-engageable with the lower interlock element of an adjacent PV shingle assembly. In some embodiments the PV shingle assembly may comprise a ventilation path below the PV body. The PV body may be slidably mounted to the connection member to facilitate removal of the PV body.

  7. Numerical noise analysis for insulator of overhead transmission line

    Science.gov (United States)

    Zhang, Yulin; Chen, Yuwen; Huang, Yu

    2018-04-01

    As an important and complex issue in aero acoustic field, a lot of explorations have been devoted to the wind-induced noise. However, there is still lack of intensive investigations for aerodynamic noise in high-voltage transmission. The overhead transmission line system leads to serious occupational noise exposure in high wind-speed environment, and the noise can even injure the electricians in charge of insulator. By using computational fluid dynamics (CFD) which combined with computational aero acoustics (CAA), this paper predicts the noise generated by insulator of high voltage electricity transmission line which explores in wind environment. The simulation results indicate that the wind velocity, the assembly angle of the insulator and its ribs' distribution are the main contributory factors for the aerodynamic noise. Specifically, when wind velocity is greater than 15m/s, the alteration of noise is not sensitive to the wind velocity; furthermore, when the assembly angle increases from 0°to 60°, the noise decreases gradually, however, if the angle is happening to be 75°or 90°, it would be even greater than that at 0°. In order to inhibit the aerodynamic noise, it is necessary to control the flow blowing across the boundary of the insulator. Consequently, the result indicates that if the outermost rib is shorter than the second one, the noise reduced evidently. This information expects to provide useful help for the extremely suppression of aerodynamic noise, and also supply practical reference material for the design and application of overhead transmission line system.

  8. Pulmonary function in automobile repair workers

    Directory of Open Access Journals (Sweden)

    Chattopadhyay O

    2007-01-01

    Full Text Available Background : Automobile repair shop is a place where workers are exposed to harmful chemicals and toxic substances. Objective : To study the occurrence of obstructive and restrictive pulmonary impairment among automobile garage workers. Methods : A cross sectional study involving 151 automobile garage workers from 14 randomly selected garages of urban Kolkata. The study variables were Forced Expiratory Volume in 1 second (FEV 1 , Forced Vital Capacity (FVC, Peak Expiratory Flow Rate (PE FR, age, smoking habit, duration of work, type of work, and respiratory symptoms. The study was analysed using Regression equations, and Chi-square test. Results : All the workers were male. Obstructive impairment was seen in 25.83% of the workers whereas restrictive impairment was seen in 21.19% of the workers. Mixed obstructive and restrictive impairment was seen in 10.6% of the workers. The frequency of obstructive impairment was higher in older workers. In the age group of less than 20 years, 13.6% of the workers had obstructive impairment while 42.86% of workers above 40 years of age had obstructive impairment. Obstructive impairment was more frequently observed in battery repair workers (58.33% and spray painters (37.5% while 16.67% of the body repair workers and 30.19% of the engine mechanics had obstructive impairment. Obstructive impairment was more frequently observed in smokers (53.1 % as compared to ex-smokers (33.3% and non-smokers (6.4%. Obstructive impairment was more frequently observed in workers who had been working for a longer duration. Conclusion: Nearly 36.4% of the automobile garage workers had some form of pulmonary function impairment; obstructive and/or restrictive. The use of personal protective equipment, worker education, and discontinuation of the use of paints containing toxic pigments are recommended.

  9. The Automated Threaded Fastening Based on On-line Identification

    Directory of Open Access Journals (Sweden)

    Nicolas Ivan Giannoccaro

    2008-11-01

    Full Text Available The principle of the thread fastenings have been known and used for decades with the purpose of joining one component to another. Threaded fastenings are popular because they permit easy disassembly for maintenance, repair, relocation and recycling. Screw insertions are typically carried out manually. It is a difficult problem to automat. As a result there is very little published research on automating threaded fastenings, and most research on automated assembly focus on the peg-in-hole assembly problem. This paper investigates the problem of automated monitoring of the screw insertion process. The monitoring problem deals with predicting integrity of a threaded insertion, based on the torque vs. insertion depth curve generated during the insertions. The authors have developed an analytical model to predict the torque signature signals during self-tapping screw insertions. However, the model requires parameters on the screw dimensions and plate material properties are difficult to measure. This paper presents a study on on-line identification during screw fastenings. An identification methodology for two unknown parameter estimation during a self-tapping screw insertion process is presented. It is shown that friction and screw properties required by the model can be reliably estimated on-line. Experimental results are presented to validate the identification procedure.

  10. Nuclear reactor fuel assembly

    International Nuclear Information System (INIS)

    Marmonier, Pierre; Mesnage, Bernard; Nervi, J.C.

    1975-01-01

    This invention refers to fuel assemblies for a liquid metal cooled fast neutron reactor. Each assembly is composed of a hollow vertical casing, of regular polygonal section, containing a bundle of clad pins filled with a fissile or fertile substance. The casing is open at its upper end and has a cylindrical foot at its lower end for positioning the assembly in a housing provided in the horizontal diagrid, on which the core assembly rests. A set of flat bars located on the external surface of the casing enables it to be correctly orientated in its housing among the other core assemblies [fr

  11. Conceptual design and development of a superconducting bus-line for the Large Helical Device

    International Nuclear Information System (INIS)

    Mito, T.; Takahata, K.; Yamada, S.; Yamamoto, J.; Uede, T.; Ikeda, M.

    1993-01-01

    A superconducting bus-line is proposed and preliminarily tested as an electrical feeder between the superconducting coils of the Large Helical Device (LHD) and their electrical power supply. The bus-line consists of a superconductor and its cryogenic transfer-line. The superconductor is a specially developed aluminum stabilized NbTi wire, which is installed in the innermost channel of the transfer-line. The vacuum insulated transfer-line consists of four corrugated tubes assembled coaxially. Liquid helium flows through the innermost channel and shield gas flows through another annular channel in the line. We are completing the conceptual design of the bus-line and the installation plan for the LHD experimental hall and are carrying out development of wires, including an investigation of their mechanical properties and electrical insulation. This report describes the conceptual design of the superconducting bus-line for the LHD, and the results we obtained recently during the design and development of a full-scale demonstration facility. (orig.)

  12. Japanese contributions to containment structure, assembly and maintenance and reactor building for ITER

    International Nuclear Information System (INIS)

    Shibanuma, Kiyoshi; Honda, Tsutomu; Kanamori, Naokazu

    1991-06-01

    Joint design work on Conceptual Design Activity of International Thermonuclear Experimental Reactor (ITER) with four parties, Japan, the United States, the Soviet Union and the European Community began in April 1988 and was successfully completed in December 1990. In Japan, the home team was established in wide range of collaboration between JAERI and national institute, universities and heavy industries. The Fusion Experimental Reactor (FER) Team at JAERI is assigned as a core of the Japanese home team to support the joint Team activity and mainly conducted the design and R and D in the area of containment structure, remote handling and plant system. This report mainly describes the Japanese contribution on the ITER containment structure, remote handling and reactor building design. Main areas of contributions are vacuum vessel, attaching locks, electromagnetic analysis, cryostat, port and service line layout for containment structure, in-vessel handling equipment design and analysis, blanket handling equipment design and related short term R and D for assembly and maintenance, and finally reactor building design and analysis based on the equipment and service line layout and components flow during assembly and maintenance. (author)

  13. Data study of death rate and cancer incidence among Thule workers, 2005; Registerundersoegelse af doedelighed og kraeftforekomst blandt Thulearbejdere, 2005

    Energy Technology Data Exchange (ETDEWEB)

    Juel, K. [Statens Insti. for Folkesundhed, Copenhagen (Denmark); Engholm, G.; Storm, H. [Kraeftens Bekaempelse, Copenhagen (Denmark)

    2005-12-01

    January 21st, 1968, an American B52 bomber with nuclear weapons aboard crashed close to the Thule air-base in Greenland. In 1986 suspicions arose that there might be increased disease incidences and death rate among the employees at the base that were involved in the clearing operations. During 1986 - 1995, several health studies were made of the Thule workers. These studies of death rate, cancer, hospitalization, and fertility did not show any differences between the Thule workers from the clearing operations and those not involved in the clearing. The present study shows no difference in total death rate among the clearing workers compared to other workers. The same results were found for cancer mortality, circulatory diseases, pulmonary diseases, natural causes, and accidents. As the previous studies showed, the present study shows that there were a slightly less number of suicides among the clearing workers. The data analyses show with great certainty that the Thule workers as a group do not have a great excessive mortality or an increased cancer incidence caused by the aircraft crash. Thus, the present results fall in line with the previous investigations. (ln)

  14. Optical Properties of GaAs Quantum Dots Fabricated by Filling of Self-Assembled Nanoholes

    Directory of Open Access Journals (Sweden)

    Heyn Ch

    2009-01-01

    Full Text Available Abstract Experimental results of the local droplet etching technique for the self-assembled formation of nanoholes and quantum rings on semiconductor surfaces are discussed. Dependent on the sample design and the process parameters, filling of nanoholes in AlGaAs generates strain-free GaAs quantum dots with either broadband optical emission or sharp photoluminescence (PL lines. Broadband emission is found for samples with completely filled flat holes, which have a very broad depth distribution. On the other hand, partly filling of deep holes yield highly uniform quantum dots with very sharp PL lines.

  15. Medical Surveillance for Former Workers

    Energy Technology Data Exchange (ETDEWEB)

    Tim Takaro

    2009-05-29

    The Former Hanford Worker Medical Monitoring Program, directed by the Occupational and Environmental Medicine Program at the University of Washington, served former production and other non-construction workers who were potentially exposed to workplace hazards while working for the USDOE or its contractors at Hanford. The USDOE Former Workers Program arose from Congressional action in the Defense Authorization of 1993 (Public Law 102). Section 3162 stated that, “The Secretary shall establish and carry out a program for the identification and ongoing medical evaluation of current and former Department of Energy employees who are subject to significant health risks as a result of exposure of such employees to hazardous or radioactive substances during such employment.” (This also covers former employees of USDOE contractors and subcontractors.) The key objective has been to provide these former workers with medical evaluations in order to determine whether workers have experienced significant risk due to workplace exposure to hazards. Exposures to asbestos, beryllium, and noise can produce specific medical conditions: asbestosis, berylliosis, and noise-induced hearing loss (NIHL). Each of these conditions can be identified by specific, non-invasive screening tests, which are widely available. Treatments are also available for individuals affected by these conditions. This project involved two phases. Phase I involved a needs and risk assessment, characterizing the nature and extent of workplace health hazards which may have increased the risk for long-term health effects. We categorized jobs and tasks by likelihood of exposures to specific workplace health hazards; and located and established contact with former Hanford workers. Phase II involved implementation of medical monitoring programs for former workers whose individual work history indicated significant risk for adverse health effects. We identified 118,000 former workers, employed from 1943 to 1997

  16. The Prevalence of Carpal Tunnel Syndrome in Latino Poultry Processing Workers and Other Latino Manual Workers

    Science.gov (United States)

    Cartwright, Michael S.; Walker, Francis O.; Blocker, Jill N.; Schulz, Mark R.; Arcury, Thomas A.; Grzywacz, Joseph G.; Mora, Dana; Chen, Haiying; Marín, Antonio J.; Quandt, Sara A.

    2011-01-01

    Objective To determine the prevalence of carpal tunnel syndrome (CTS) in Latino poultry processing workers. Methods Symptoms and nerve conduction studies were used to prospectively assess 287 Latino poultry processing workers and 226 Latinos in other manual labor occupations. Results The prevalence of CTS was higher in poultry processing (8.7%) compared to non-poultry manual workers (4.0%, p poultry workers was 2.51 (95% CI of 1.80 to 3.50) compared to non-poultry workers. Within the poultry workers, those who performed packing, sanitation, and chilling had a trend toward less CTS than those who performed tasks requiring more repetitive and strenuous hand movements. Discussion Latino poultry processing workers have a high prevalence of CTS, which likely results from the repetitive and strenuous nature of the work. PMID:22258161

  17. Self assembly of rectangular shapes on concentration programming and probabilistic tile assembly models.

    Science.gov (United States)

    Kundeti, Vamsi; Rajasekaran, Sanguthevar

    2012-06-01

    Efficient tile sets for self assembling rectilinear shapes is of critical importance in algorithmic self assembly. A lower bound on the tile complexity of any deterministic self assembly system for an n × n square is [Formula: see text] (inferred from the Kolmogrov complexity). Deterministic self assembly systems with an optimal tile complexity have been designed for squares and related shapes in the past. However designing [Formula: see text] unique tiles specific to a shape is still an intensive task in the laboratory. On the other hand copies of a tile can be made rapidly using PCR (polymerase chain reaction) experiments. This led to the study of self assembly on tile concentration programming models. We present two major results in this paper on the concentration programming model. First we show how to self assemble rectangles with a fixed aspect ratio ( α:β ), with high probability, using Θ( α + β ) tiles. This result is much stronger than the existing results by Kao et al. (Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008) and Doty (Randomized self-assembly for exact shapes. In: proceedings of the 50th annual IEEE symposium on foundations of computer science (FOCS), IEEE, Atlanta. pp 85-94, 2009)-which can only self assembly squares and rely on tiles which perform binary arithmetic. On the other hand, our result is based on a technique called staircase sampling . This technique eliminates the need for sub-tiles which perform binary arithmetic, reduces the constant in the asymptotic bound, and eliminates the need for approximate frames (Kao et al. Randomized self-assembly for approximate shapes, LNCS, vol 5125. Springer, Heidelberg, 2008). Our second result applies staircase sampling on the equimolar concentration programming model (The tile complexity of linear assemblies. In: proceedings of the 36th international colloquium automata, languages and programming: Part I on ICALP '09, Springer-Verlag, pp 235

  18. Assembling large, complex environmental metagenomes

    Energy Technology Data Exchange (ETDEWEB)

    Howe, A. C. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Jansson, J. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Earth Sciences Division; Malfatti, S. A. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tringe, S. G. [USDOE Joint Genome Institute (JGI), Walnut Creek, CA (United States); Tiedje, J. M. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Plant Soil and Microbial Sciences; Brown, C. T. [Michigan State Univ., East Lansing, MI (United States). Microbiology and Molecular Genetics, Computer Science and Engineering

    2012-12-28

    The large volumes of sequencing data required to sample complex environments deeply pose new challenges to sequence analysis approaches. De novo metagenomic assembly effectively reduces the total amount of data to be analyzed but requires significant computational resources. We apply two pre-assembly filtering approaches, digital normalization and partitioning, to make large metagenome assemblies more computationaly tractable. Using a human gut mock community dataset, we demonstrate that these methods result in assemblies nearly identical to assemblies from unprocessed data. We then assemble two large soil metagenomes from matched Iowa corn and native prairie soils. The predicted functional content and phylogenetic origin of the assembled contigs indicate significant taxonomic differences despite similar function. The assembly strategies presented are generic and can be extended to any metagenome; full source code is freely available under a BSD license.

  19. Worker flag. Independent Electrical Policy

    International Nuclear Information System (INIS)

    Bahen, D.

    2000-01-01

    This work analyses the initiative of privatization of the Mexican Electric Industry and also it is showed the incoherence of this mistaken proposal. Along the same line is analysed tthe situation of the National Electric Sector and the working process for the distinct types of electric generation just as the syndical and labor situations. In consequence it is proposed an Independent Electrical Policy, which includes the integration of the Nationalized Electric Industry, the syndical union and the Unique Collective Contract. The purpose of this work is to contribute to the success of the electrical and nuclear struggle always maintaining in rising position the red flag of the proletariat. The author considers that the privatization means mercantilization of the human necessities. The privatization is not inevitable at condition of to exercise consequently the political actions necessary through alternatives includes: the worker control of production, research, and the National Electric strike. (Author)

  20. Nuclear fuel string assembly

    International Nuclear Information System (INIS)

    Ip, A.K.; Koyanagi, K.; Tarasuk, W.R.

    1976-01-01

    A method of fabricating rodded fuels suitable for use in pressure tube type reactors and in pressure vessel type reactors is described. Fuel rods are secured as an inner and an outer sub-assembly, each rod attached between mounting rings secured to the rod ends. The two sub-assemblies are telescoped together and positioned by spaced thimbles located between them to provide precise positioning while permittng differential axial movement between the sub-assemblies. Such sub-assemblies are particularly suited for mounting as bundle strings. The method provides particular advantages in the assembly of annular-section fuel pins, which includes booster fuel containing enriched fuel material. (LL)

  1. Multikanban model for disassembly line with demand fluctuation

    Science.gov (United States)

    Udomsawat, Gun; Gupta, Surendra M.; Al-Turki, Yousef A. Y.

    2004-02-01

    In recent years, the continuous growth in consumer waste and dwindling natural resources has seriously threatened the environment. Realizing this, several countries have passed regulations that force manufacturers not only to manufacture environmentally conscious products, but also to take back their used products from consumers so that the components and materials recovered from the products may be reused and/or recycled. Disassembly plays an important role in product recovery. A disassembly line is perhaps the most suitable setting for disassembly of products in large quantities. Because a disassembly line has a tendency to generate excessive inventory, employing a kanban system can reduce the inventory level and let the system run more efficiently. A disassembly line is quite different from an assembly line. For example, not only can the demand arrive at the last station, it can also arrive at any of the other stations in the system. The demand for a component on the disassembly line could fluctuate widely. In fact, there are many other complicating matters that need to be considered to implement the concept of kanbans in such an environment. In this paper, we discuss the complications that are unique to a disassembly line. We discuss the complications in utilizing the conventional production control mechanisms in a disassembly line setting. We then show how to overcome them by implementing kanbans in a disassembly line setting with demand fluctuation and introduce the concept of multi-kanban mechanism. We demonstrate its effectiveness using a simulation model. An example is presented to illustrate the concept.

  2. Strategies of performance self-monitoring in automotive production.

    Science.gov (United States)

    Faye, Hélène; Falzon, Pierre

    2009-09-01

    Production in the automotive industry, based on assembly line work, is now characterized by lean manufacturing and customization. This results in greater flexibility and increased quality demands, including worker performance self-monitoring. The objectives of this study are to refine the concept of performance self-monitoring and to characterize the strategies developed by operators to achieve it. Data were collected based on the method of individual auto-confrontation, consisting of two steps: eleven assembly-line operators of a French automotive company were individually observed and video-taped while they were working; an interview then allowed each operator to discuss his/her activity based on the video-tape. This study expands the concept of performance self-monitoring by highlighting three types of strategies directly oriented toward quality: prevention, feedback control and control action strategies.

  3. A novel detector assembly for detecting thermal neutrons, fast neutrons and gamma rays

    Energy Technology Data Exchange (ETDEWEB)

    Cester, D., E-mail: davide.cester@gmail.com [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); Lunardon, M.; Moretto, S. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); INFN Sezione di Padova, Via Marzolo 8, I-35131 Padova (Italy); Nebbia, G. [INFN Sezione di Padova, Via Marzolo 8, I-35131 Padova (Italy); Pino, F. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); Sajo-Bohus, L. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy); Laboratorio de Fisica Nuclear, Universidad Simon Bolivar, Apartado 89000, 1080 A Caracas (Venezuela, Bolivarian Republic of); Stevanato, L.; Bonesso, I.; Turato, F. [Dipartimento di Fisica ed Astronomia dell' Università di Padova, Via Marzolo 8, I-35131 Padova (Italy)

    2016-09-11

    A new composite detector has been developed by combining two different commercial scintillators. The device has the capability to detect gamma rays as well as thermal and fast neutrons; the signal discrimination between the three types is performed on-line by means of waveform digitizers and PSD algorithms. This work describes the assembled detector and its discrimination performance to be employed in the applied field.

  4. A novel detector assembly for detecting thermal neutrons, fast neutrons and gamma rays

    International Nuclear Information System (INIS)

    Cester, D.; Lunardon, M.; Moretto, S.; Nebbia, G.; Pino, F.; Sajo-Bohus, L.; Stevanato, L.; Bonesso, I.; Turato, F.

    2016-01-01

    A new composite detector has been developed by combining two different commercial scintillators. The device has the capability to detect gamma rays as well as thermal and fast neutrons; the signal discrimination between the three types is performed on-line by means of waveform digitizers and PSD algorithms. This work describes the assembled detector and its discrimination performance to be employed in the applied field.

  5. The representation of sex workers in South African media: Danger, morals and human rights

    Directory of Open Access Journals (Sweden)

    Sally Hunt

    2015-09-01

    Full Text Available The ideological construct of gender typically positions women below men, and “others” certain types of women even more, especially those distinguished from idealised femininity by aspects of their sexuality. This paper explores the representation of sex work and sex workers in the South African media in 2009 and 2010, a time during which there was an increase in news coverage of sex work during the 2010 FIFA World Cup. Analysis of the two data sets revealed that sex work is still often perceived as immoral and dangerous, and that sex workers – overwhelmingly represented as women – are criminalised for their actions while client agency is largely obscured, which is in line with previous studies of South African newspapers. However, a strong liberal representation of sex workers was also found in one data set, which advocates the decriminalisation of sex work in the context of human rights. The use of the term “sex work” and its derivatives, rather than “prostitution”, was found to index this progressive stance.

  6. Organ printing: from bioprinter to organ biofabrication line.

    Science.gov (United States)

    Mironov, Vladimir; Kasyanov, Vladimir; Markwald, Roger R

    2011-10-01

    Organ printing, or the layer by layer additive robotic biofabrication of functional three-dimensional tissue and organ constructs using self-assembling tissue spheroid building blocks, is a rapidly emerging technology that promises to transform tissue engineering into a commercially successful biomedical industry. It is increasingly obvious that similar well-established industries implement automated robotic systems on the path to commercial translation and economic success. The use of robotic bioprinters alone however is not sufficient for the development of large industrial scale organ biofabrication. The design and development of a fully integrated organ biofabrication line is imperative for the commercial translation of organ printing technology. This paper presents recent progress and challenges in the development of the essential components of an organ biofabrication line. Copyright © 2011 Elsevier Ltd. All rights reserved.

  7. Effects of subtle differences in ligand constitution and conformation in metallo-supramolecular self-assembled polygons.

    Science.gov (United States)

    Brusilowskij, Boris; Dzyuba, Egor V; Troff, Ralf W; Schalley, Christoph A

    2011-12-07

    3,3'-Bis(pyridin-[n]-ylethynyl)biphenyl (n = 3, 4) and the corresponding 2,2'-bipyridines assemble with (dppp)Pt(II) triflate into metallo-supramolecular polygons. Depending on the position of the terminal pyridine N atoms, the assembly reaction leads to different equilibrium products. With the slow ligand exchange on Pt(II) complexes, the equilibrium is reached on a many-hour time-scale. During the assembly process, larger polygons form under kinetic control. This was confirmed by time-dependent (1)H and (31)P NMR spectroscopy in line with complementary ESI mass spectrometric experiments. The constitutional difference in the pyridine N-atom position is reflected in the tandem mass spectra of the complex ions. In addition, a highly specific fragmentation process of mass-selected M(3)L(3) ions was observed, which proceeds through a ring contraction yielding smaller M(2)L(2) ions.

  8. Study of insomnia in rotating shift-workers

    Directory of Open Access Journals (Sweden)

    Kaushik Chatterjee

    2017-01-01

    Full Text Available Background: Shift-workers commonly suffer from insomnia. This study evaluates different domains of insomnia. Aim: This study was aimed to study sleep and insomnia in rotating shift-workers and compare with day-workers. Materials and Methods: This was case–control study. The sleep of rotating shift-workers is compared with day workers using Athens Insomnia Scale. Results: Rotating shift-workers had significantly higher scores on Athens insomnia scale on domains of initial, intermediate and terminal insomnia than day workers. Duration and quality of sleep and sense of well-being are lower in rotating shift-workers. Rotating shift-workers also experienced more day-time sleepiness than day workers. However, there was no difference in perceived physical and mental functioning between the two groups. Conclusion: Individuals working in rotating shifts for more than 15 days have significantly higher prevalence of insomnia than day-workers.

  9. Reflector-moderated critical assemblies

    International Nuclear Information System (INIS)

    Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

    1975-07-01

    Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

  10. SWAP-Assembler 2: Optimization of De Novo Genome Assembler at Large Scale

    Energy Technology Data Exchange (ETDEWEB)

    Meng, Jintao; Seo, Sangmin; Balaji, Pavan; Wei, Yanjie; Wang, Bingqiang; Feng, Shengzhong

    2016-08-16

    In this paper, we analyze and optimize the most time-consuming steps of the SWAP-Assembler, a parallel genome assembler, so that it can scale to a large number of cores for huge genomes with the size of sequencing data ranging from terabyes to petabytes. According to the performance analysis results, the most time-consuming steps are input parallelization, k-mer graph construction, and graph simplification (edge merging). For the input parallelization, the input data is divided into virtual fragments with nearly equal size, and the start position and end position of each fragment are automatically separated at the beginning of the reads. In k-mer graph construction, in order to improve the communication efficiency, the message size is kept constant between any two processes by proportionally increasing the number of nucleotides to the number of processes in the input parallelization step for each round. The memory usage is also decreased because only a small part of the input data is processed in each round. With graph simplification, the communication protocol reduces the number of communication loops from four to two loops and decreases the idle communication time. The optimized assembler is denoted as SWAP-Assembler 2 (SWAP2). In our experiments using a 1000 Genomes project dataset of 4 terabytes (the largest dataset ever used for assembling) on the supercomputer Mira, the results show that SWAP2 scales to 131,072 cores with an efficiency of 40%. We also compared our work with both the HipMER assembler and the SWAP-Assembler. On the Yanhuang dataset of 300 gigabytes, SWAP2 shows a 3X speedup and 4X better scalability compared with the HipMer assembler and is 45 times faster than the SWAP-Assembler. The SWAP2 software is available at https://sourceforge.net/projects/swapassembler.

  11. Risks for radiation workers

    International Nuclear Information System (INIS)

    Rotblat, J.

    1978-01-01

    The following topics are discussed: recommendations of the International Commission on Radiological Protection; methods for determining dose limits to workers; use of data from survivors of Hiroshima and Nagasaki for estimating risk factors; use of data from survivors of nuclear explosions in Marshall Islands, uranium miners, and patients exposed to diagnostic and therapeutic radiation; risk factors for radioinduced malignancies; evidence that risk factors for persons exposed to partial-body radiation and Japanese survivors are too low; greater resistance of A-bomb survivors to radiation; and radiation doses received by U.K. medical workers and by U.K. fuel reprocessing workers. It is suggested that the dose limit for radiation workers should be reduced by a factor of 5

  12. Advanced worker protection system

    Energy Technology Data Exchange (ETDEWEB)

    Caldwell, B.; Duncan, P.; Myers, J. [Oceaneering Space Systems, Houston, TX (United States)

    1995-10-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D&D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D&D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D&D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project describes the development of an Advanced Worker Protection System (AWPS) which will include a life-support backpack with liquid air for cooling and as a supply of breathing gas, protective clothing, respirators, communications, and support equipment.

  13. Radiation haunts shipyard workers

    International Nuclear Information System (INIS)

    Torrey, L.

    1978-01-01

    The apparent link recently found by Dr. Najarian between cancer among workers at a US Naval dockyard where up to 5000 civilian employees have been exposed to low dose irradiation while servicing nuclear ships and their radiation exposure is discussed. The study has revealed that 38.4% of the deaths of nuclear workers at the Portsmouth Naval Shipyard in New Hampshire were caused by cancer while the comparable rate for non-nuclear shipyard workers was 21.7% and the national average in the United States is 18%. The Portsmouth study, launched in October 1977, was based on a survey of 1722 death certificates of shipyard employees and interviews with 592 next-of-kin. In addition the results show that the rate of leukaemia of the shipyard workers was 450% higher than that of the general population, and the incidence of lymph gland cancers was 125% higher than the national rate. The most startling statistics compared mortality among workers aged 60 to 69. In this age group nearly 60% of the nuclear employees had died of cancer, while the cancer death rate among non-nuclear workers was only 26%. If these results are confirmed present ideas concerning the effects of low doses of radiation must be challenged. (U.K.)

  14. Advanced worker protection system

    International Nuclear Information System (INIS)

    Caldwell, B.; Duncan, P.; Myers, J.

    1995-01-01

    The Department of Energy (DOE) is in the process of defining the magnitude and diversity of Decontamination and Decommissioning (D ampersand D) obligations at its numerous sites. The DOE believes that existing technologies are inadequate to solve many challenging problems such as how to decontaminate structures and equipment cost effectively, what to do with materials and wastes generated, and how to adequately protect workers and the environment. Preliminary estimates show a tremendous need for effective use of resources over a relatively long period (over 30 years). Several technologies are being investigated which can potentially reduce D ampersand D costs while providing appropriate protection to DOE workers. The DOE recognizes that traditional methods used by the EPA in hazardous waste site clean up activities are insufficient to provide the needed protection and worker productivity demanded by DOE D ampersand D programs. As a consequence, new clothing and equipment which can adequately protect workers while providing increases in worker productivity are being sought for implementation at DOE sites. This project describes the development of an Advanced Worker Protection System (AWPS) which will include a life-support backpack with liquid air for cooling and as a supply of breathing gas, protective clothing, respirators, communications, and support equipment

  15. Line Balancing Using Largest Candidate Rule Algorithm In A Garment Industry: A Case Study

    Directory of Open Access Journals (Sweden)

    V. P.Jaganathan

    2014-12-01

    Full Text Available The emergence of fast changes in fashion has given rise to the need to shorten production cycle times in the garment industry. As effective usage of resources has a significant effect on the productivity and efficiency of production operations, garment manufacturers are urged to utilize their resources effectively in order to meet dynamic customer demand. This paper focuses specifically on line balancing and layout modification. The aim of assembly line balance in sewing lines is to assign tasks to the workstations, so that the machines of the workstation can perform the assigned tasks with a balanced loading. Largest Candidate Rule Algorithm (LCR has been deployed in this paper.

  16. Cervical cancer screening in rural South Africa among HIV-infected migrant farm workers and sex workers.

    Science.gov (United States)

    Afzal, Omara; Lieber, Molly; Dottino, Peter; Beddoe, Ann Marie

    2017-05-01

    At an HIV clinic in the Limpopo province of South Africa, chart reviews revealed long delays in addressing abnormal Pap smears, difficulty in referrals, poor quality and lost results, and increasing cases of cervical cancer. To address these barriers, a "see and treat" approach to screening was proposed. The objective was to integrate this method into current HIV care offered by local providers and to obtain demographic and risk factor data for use in future educational and intervention programs in the region. A cross sectional study of HIV farm workers and at-risk sex workers attending an HIV clinic was performed with visual inspection with acetic acid (VIA). Those with positive screens were offered cryotherapy. Clinic charts were reviewed retrospectively for Pap smear results for the previous year at the time of program initiation and at 12 and 18 months post-program. A total of 403 participants consented and underwent screening with VIA (306 Farm workers and 97 sex workers participated). 83.9% of participants (32.9% sex workers and 100% farm workers) were HIV +. VIA was positive in 30.5% of participants, necessitating cryotherapy. There was no significant difference in VIA positivity between HIV + farm workers and sex workers. There was a positive correlation between Pap smears and VIAs results. We demonstrate successful integration of cervical cancer screening using VIA for HIV + farm workers and sex workers into an existing HIV treatment and prevention clinic in rural South Africa, addressing and treating abnormal results promptly.

  17. Making the most of on-line recruiting.

    Science.gov (United States)

    Cappelli, P

    2001-03-01

    Ninety percent of large U.S. companies are already recruiting via the Internet. By simply logging on to the Web, company recruiters can locate vast numbers of qualified candidates for jobs at every level, screen them in minutes, and contact the most promising ones immediately. The payoffs can be enormous: it costs substantially less to hire someone on-line, and the time saved is equally great. In this article, Peter Cappelli examines some of the emerging service providers and technologies--matchmakers, job boards, hiring management systems software, and applicant-screening mechanisms that test skills and record interests. He also looks at some of the strategies companies are adopting as they enter on-line labor markets. Recruiting needs to be refashioned to resemble marketing, he stresses. Accordingly, smart companies are designing Web pages, and even product ads, with potential recruits in mind. They're giving line managers authority to hire so that candidates in cyberspace aren't lost. They're building internal on-line job networks to retain talent. Integrating recruiting efforts with overall marketing campaigns, especially through coordination and identification with the company's brand, is the most important thing companies can do to ensure success in on-line hiring. Along the way, Cappelli sounds two cautionary notes. First, a human touch, not electronic contact, is vital in the last steps of a successful hiring process. Second, companies must make sure that on-line testing and hiring criteria do not discriminate against women, disabled people, workers over 40, or members of minority groups. When competition for talent is fierce, companies that master the art and science of on-line recruiting will be the ones that attract and keep the best people.

  18. The Metal Effect on Self-Assembling of Oxalamide Gelators Explored by Mass Spectrometry and DFT Calculations

    Science.gov (United States)

    Dabić, Dario; Brkljačić, Lidija; Tandarić, Tana; Žinić, Mladen; Vianello, Robert; Frkanec, Leo; Kobetić, Renata

    2018-01-01

    Gels formed by self-assembly of small organic molecules are of wide interest as dynamic soft materials with numerous possible applications, especially in terms of nanotechnology for functional and responsive biomaterials, biosensors, and nanowires. Four bis-oxalamides were chosen to show if electrospray ionization mass spectrometry (ESI-MS) could be used as a prediction of a good gelator and also to shed light on the gelation processes. By inspecting the gelation of several solvent, we showed that bis(amino acid)oxalamide 1 proved to be the most efficient, also being able of forming the largest observable assemblies in the gas phase. The formation of singly charged assemblies holding from one up to six monomer units is the outcome of the strong intermolecular H-bonds, particularly among terminal carboxyl groups. The variation of solvents from polar aprotic towards polar protic did not have any significant effects on the size of the assemblies. The addition of a salt such as NaOAc or Mg(OAc)2, depending on the concentration, altered the assembling. Computational analysis at the DFT level aided in the interpretation of the observed trends and revealed that individual gelator molecules spontaneously assemble to higher aggregates, but the presence of the Na+ cation disrupts any gelator organization since it becomes significantly more favorable for gelator molecules to bind Na+ cations up to the 3:1 ratio than to self-assemble, being fully in line with experimental observations reported here. [Figure not available: see fulltext.

  19. Polymer Directed Protein Assemblies

    NARCIS (Netherlands)

    van Rijn, Patrick

    2013-01-01

    Protein aggregation and protein self-assembly is an important occurrence in natural systems, and is in some form or other dictated by biopolymers. Very obvious influences of biopolymers on protein assemblies are, e. g., virus particles. Viruses are a multi-protein assembly of which the morphology is

  20. Common understanding of Emergency Workers

    International Nuclear Information System (INIS)

    2015-11-01

    While the protection of Emergency Workers is regulated in most countries, national definitions, respectively interpretations differ. The prevailing regulatory frameworks are: - Basic Safety Standards (2013/59/EURATOM) The Basis Safety Standards (BSS) are binding for members of the EU. The BSS give a definition of Emergency Workers. - IAEA General Safety Requirements Part 7 (Draft). The Agency's definition is consistent with the BSS-definition. In addition, the Helper is defined. - The Nordic Flag-book. The Nordic Flag-book's Emergency Worker is consistent with the BSS-definition. In addition, workers are defined. Flag-book-Workers (FBW) are neither coterminous with GSR-P-7-helpers nor with BSS-workers. The possible need for harmonization was assessed by the means of a questionnaire, asking members of the Working Group Emergencies to attribute regulatory categories to different roles that might arise in an emergency. While showing a rich variation in interpretations, there is general agreement for the most important roles. Wherever differences are found, the bilateral impact is deemed to be marginal at worst. Therefore, no need for harmonisation with respect to the concept of Emergency Workers is seen

  1. 76 FR 61741 - Bmc Software, Inc. Including On-Site Leased Workers From COMSYS ITS Including Remote Workers...

    Science.gov (United States)

    2011-10-05

    ... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-74,540] Bmc Software, Inc... November 23, 2010, applicable to workers of BMC Software, Inc., including on-site leased workers from... BMC Software, inc., including on-site leased workers from Comsys ITS, and including remote workers...

  2. A comparison of male sex workers in Prague: Internet escorts versus men who work in specialized bars and clubs.

    Science.gov (United States)

    Bar-Johnson, Michael David; Weiss, Petr

    2015-01-01

    Prague, the Czech Republic, is a popular sex tourism destination where sex work is decriminalized and young men offer sexual services at low prices relative to countries in Western Europe. This quantitative survey aimed to identify some of the demographic characteristics of these young men and their experiences in the sex industry. Internet escorts (N = 20) and sex workers in bars and clubs (N = 20) completed the survey anonymously in spring 2011. The results showed that sex workers in clubs often had troubled pasts and were forced into sex work to survive. They also reported incidents of violence, serious alcohol and drug use, as well as frequent gambling. The larger group of sex workers in Prague is made up of Internet escorts who have backgrounds that are not atypical for the average Czech youth. They had fewer problems with drugs and alcohol but were twice as likely as sex workers in bars and clubs to be victims of violent crime. Plans for interventions to help those who would change their line of work, as well as the importance of sociocultural context in understanding sex workers, are discussed.

  3. Core/coil assembly for use in superconducting magnets and method for assembling the same

    Science.gov (United States)

    Kassner, David A.

    1979-01-01

    A core/coil assembly for use in a superconducting magnet of the focusing or bending type used in syncronous particle accelerators comprising a coil assembly contained within an axial bore of the stacked, washer type, carbon steel laminations which comprise the magnet core assembly, and forming an interference fit with said laminations at the operating temperature of said magnet. Also a method for making such core/coil assemblies comprising the steps of cooling the coil assembly to cryogenic temperatures and drawing it rapidly upwards into the bore of said stacked laminations.

  4. Workers' marginal costs of commuting

    DEFF Research Database (Denmark)

    van Ommeren, Jos; Fosgerau, Mogens

    2009-01-01

    This paper applies a dynamic search model to estimate workers' marginal costs of commuting, including monetary and time costs. Using data on workers' job search activity as well as moving behaviour, for the Netherlands, we provide evidence that, on average, workers' marginal costs of one hour...

  5. Final configuration with assembly assessment of the 100 kV high voltage bushing for the Indian test facility

    International Nuclear Information System (INIS)

    Sharma, Dheeraj Kumar; Shah, Sejal; Venkata Nagaraju, M.; Bandyopadhyay, Mainak; Rotti, Chandramouli; Chakraborty, Arun Kumar

    2015-01-01

    The Indian Test Facility (INTF) of Neutral Beam (NB) system is an Indian voluntary effort for the full characterization of the diagnostic neutral beam which is the part of ITER's neutral beam system. The design activities of INTF NB system are completed. The INTF High Voltage Bushing (HVB), which is one of the component of NB system, is designed to connect all the required feedlines, e.g. electrical busbars, RF co-axial lines, diagnostic lines and hydraulic and gas feed lines, carried by the transmission line from the HV deck to the Beam Source of NB system. It forms the primary vacuum boundary and provides 100 kV isolation for INTF beam operation. The entire feedlines pass through a metallic plate of HVB called Dished Head (DH) where all the feedlines converge. The overall diameter of DH is 847 mm which is governed by the diameter of the Porcelain insulator which is meant for 100 kV isolation. The effective diameter where all the feedlines converge at the dished head is ∼ 600 mm which is quite a challenge to accommodate 26 feedlines each of average diameter 60 mm. Electrical feedlines require Vacuum-Electrical feedthroughs for voltage isolation whereas water and gas lines are considered to be directly welded with the DH except one water line which requires 12 kV voltage isolation with respect to DH. For RF lines, different scheme is considered which includes separate Electrical Feedthrough and Vacuum Barrier. To provide connection to electrical cables of heaters and thermocouples, 4 numbers of multipin vacuum compatible electrical feedthroughs are provided which can accommodate ∼250 cables. Due to space constraints, Vacuum-Electrical Feedthroughs are considered to be welded with the DH and therefore they shall be of metal-ceramic-metal configuration to allow welding. To avoid undue loading on the ceramic part, the feedlines are supported additionally at DH using vacuum compatible and electrically insulating material. One more important aspect of the INTF

  6. The weather-stains of care: interpreting the meaning of bad weather for front-line health care workers in rural long-term care.

    Science.gov (United States)

    Joseph, Gillian M; Skinner, Mark W; Yantzi, Nicole M

    2013-08-01

    This paper addresses the gap in health services and policy research about the implications of everyday weather for health care work. Building on previous research on the weather-related challenges of caregiving in homes and communities, it examines the experiences of 'seasonal bad weather' for health care workers in long-term care institutions. It features a hermeneutic phenomenology analysis of six transcripts from interviews with nurses and personal support workers from a qualitative study of institutional long-term care work in rural Canada. Focussing on van Manen's existential themes of lived experience (body, relations, space, time), the analysis reveals important contradictions between the lived experiences of health care workers coping with bad weather and long-term care policies and practices that mitigate weather-related risk and vulnerability. The findings contribute to the growing concern for rural health issues particularly the neglected experiences of rural health providers and, in doing so, offer insight into the recent call for greater attention to the geographies of health care work. Copyright © 2012 Elsevier Ltd. All rights reserved.

  7. Analytical evaluation of work ability index and its determining factors among workers of a car manufacturing industry

    Directory of Open Access Journals (Sweden)

    M Eyvazlou

    2012-11-01

    Full Text Available   Background and aims : The ability of work is the basis of well-being for all of us. Many factors affect the work ability such as work and work condition, work organization and human resource. The aim of this study was to assess the work ability among car manufacturing workers and determine the relationship between the work ability index with individual characteristics and life style factors.   Methods : The study was a descriptive cross-sectional investigation. The subjects comprised of 271 workers­ with mean age of 35 years who occupied by a car manufacturing Company. They completed the Work Ability Index Questionnaire during semi interview sessions. The job groups of Painting Shop, assembling line, office department, and technical section were studied. Statistical tests including one-way­ ANOVA, t-test, Kruskal wallis were used for analyzing the relationship between work ability index and individual characteristic as well as life style factors. To test the distribution of work ability index score categories, a chi-square test was used and finally, Spearman correlation coefficient was used in order to determine correlation between the final of work ability index score with any of questionnaire items.   Results : The mean value of work ability index in this study was (37.67 with SD=5.87. The WAI categories were 17.71% in "excellent", 38.75% in "good", 36.16% in "moderate", and 7.4% in "poor" levels. Association between life style factors (obesity, smoking, exercise and WAI was statistically significant (P< .0.001 . Lower WAI was associated with increasing the age, high work experience and lower education (P<.0.001. Meanwhile, physical demand of the jobs was strongly associated with the WAI score (P<.0.001. Conclusion : On the basis of Finnish Institute of Occupational Health, the value of work ability in current study was in good category(37-43; but, concerning the mean age (35 years of the studied population the mean value of work

  8. 75 FR 6031 - Policy Paper on Revised Risk Assessment Methods for Workers, Children of Workers in Agricultural...

    Science.gov (United States)

    2010-02-05

    ... and its relationship to several other key Agency initiatives that are currently under development and... Assessment Methods for Workers, Children of Workers in Agricultural Fields, and Pesticides with No Food Uses... for comment a policy paper entitled ``Revised Risk Assessment Methods for Workers, Children of Workers...

  9. Why do women choose an unregulated birth worker to birth at home in Australia: a qualitative study.

    Science.gov (United States)

    Rigg, Elizabeth Christine; Schmied, Virginia; Peters, Kath; Dahlen, Hannah Grace

    2017-03-28

    In Australia the choice to birth at home is not well supported and only 0.4% of women give birth at home with a registered midwife. Recent changes to regulatory requirements for midwives have become more restrictive and there is no insurance product that covers private midwives for intrapartum care at home. Freebirth (planned birth at home with no registered health professional) with an unregulated birth worker who is not a registered midwife or doctor (e.g. Doula, ex-midwife, lay midwife etc.) appears to have increased in Australia. The aim of this study is to explore the reasons why women choose to give birth at home with an unregulated birth worker (UBW) from the perspective of women and UBWs. Nine participants (five women who had UBWs at their birth and four UBWs who had themselves used UBWs in the past for their births) were interviewed in-depth and the data analysed using thematic analysis. Four themes were found: 'A traumatising system', 'An inflexible system'; 'Getting the best of both worlds' and 'Treated with love and respect versus the mechanical arm on the car assembly line'. Women interviewed for this study either experienced or were exposed to mainstream care, which they found traumatising. They were not able to access their preferred birth choices, which caused them to perceive the system as inflexible. They interpreted this as having no choice when choice was important to them. The motivation then became to seek alternative options of care that would more appropriately meet their needs, and help avoid repeated trauma through mainstream care. Women who engaged UBWs viewed them as providing the best of both worlds - this was birthing at home with a knowledgeable person who was unconstrained by rules or regulations and who respected and supported the woman's philosophical view of birth. Women perceived UBWs as not only the best opportunity to achieve a natural birth but also as providing 'a safety net' in case access to emergency care was required.

  10. Physiology of reproductive worker honey bees (Apis mellifera): insights for the development of the worker caste.

    Science.gov (United States)

    Peso, Marianne; Even, Naïla; Søvik, Eirik; Naeger, Nicholas L; Robinson, Gene E; Barron, Andrew B

    2016-02-01

    Reproductive and behavioural specialisations characterise advanced social insect societies. Typically, the honey bee (Apis mellifera) shows a pronounced reproductive division of labour between worker and queen castes, and a clear division of colony roles among workers. In a queenless condition, however, both of these aspects of social organisation break down. Queenless workers reproduce, forage and maintain their colony operating in a manner similar to communal bees, rather than as an advanced eusocial group. This plasticity in social organisation provides a natural experiment for exploring physiological mechanisms of division of labour. We measured brain biogenic amine (BA) levels and abdominal fat body vitellogenin gene expression levels of workers in queenright and queenless colonies. Age, ovary activation and social environment influenced brain BA levels in honey bees. BA levels were most influenced by ovary activation state in queenless bees. Vitellogenin expression levels were higher in queenless workers than queenright workers, but in both colony environments vitellogenin expression was lower in foragers than non-foragers. We propose this plasticity in the interacting signalling systems that influence both reproductive and behavioural development allows queenless workers to deviate significantly from the typical worker bee reaction norm and develop as reproductively active behavioural generalists.

  11. Nuclear fuel assemblies and fuel pins usable in such assemblies

    International Nuclear Information System (INIS)

    Jolly, R.

    1982-01-01

    A novel end cap for a nuclear fuel assembly is described in detail. It consists of a trisection arrangement which is received within a cell of a cellular grid. The cell contains abutment means with which the trisection comes into abutment. The grid also contains an abutment means for preventing the trisections from being inserted into the cell in an incorrect orientation. The present design allows fuel pins to be securely held in a hold-down grid of a sub-assembly. The design also allows easier dis-assembly of the swollen and embrittled fuel pins prior to reprocessing. (U.K.)

  12. Secretion of hepatitis C virus envelope glycoproteins depends on assembly of apolipoprotein B positive lipoproteins.

    Directory of Open Access Journals (Sweden)

    Vinca Icard

    Full Text Available The density of circulating hepatitis C virus (HCV particles in the blood of chronically infected patients is very heterogeneous. The very low density of some particles has been attributed to an association of the virus with apolipoprotein B (apoB positive and triglyceride rich lipoproteins (TRL likely resulting in hybrid lipoproteins known as lipo-viro-particles (LVP containing the viral envelope glycoproteins E1 and E2, capsid and viral RNA. The specific infectivity of these particles has been shown to be higher than the infectivity of particles of higher density. The nature of the association of HCV particles with lipoproteins remains elusive and the role of apolipoproteins in the synthesis and assembly of the viral particles is unknown. The human intestinal Caco-2 cell line differentiates in vitro into polarized and apoB secreting cells during asymmetric culture on porous filters. By using this cell culture system, cells stably expressing E1 and E2 secreted the glycoproteins into the basal culture medium after one week of differentiation concomitantly with TRL secretion. Secreted glycoproteins were only detected in apoB containing density fractions. The E1-E2 and apoB containing particles were unique complexes bearing the envelope glycoproteins at their surface since apoB could be co-immunoprecipitated with E2-specific antibodies. Envelope protein secretion was reduced by inhibiting the lipidation of apoB with an inhibitor of the microsomal triglyceride transfer protein. HCV glycoproteins were similarly secreted in association with TRL from the human liver cell line HepG2 but not by Huh-7 and Huh-7.5 hepatoma cells that proved deficient for lipoprotein assembly. These data indicate that HCV envelope glycoproteins have the intrinsic capacity to utilize apoB synthesis and lipoprotein assembly machinery even in the absence of the other HCV proteins. A model for LVP assembly is proposed.

  13. Self-assembly of coiled coil peptides into nanoparticles vs 2-d plates: effects of assembly pathway

    Science.gov (United States)

    Kim, Kyunghee; Pochan, Darrin

    Molecular solution assembly, or self-assembly, is a process by which ordered nanostructures or patterns are formed by non-covalent interactions during assembly. Biomimicry, the use of bioinspired molecules or biologically relevant materials, is an important area of self-assembly research with peptides serving a critical role as molecular tools. The morphology of peptide assemblies can be controlled by adjusting solution conditions such as the concentration of peptides, the temperature, and pH. Herein, spherical nanostructures, which have potential for creating an encapsulation system, are formed by self-assembly when coiled coil peptides are combined in solution. These peptides are homotrimeric and heterodimeric coiled-coil bundles and the homotrimer is connected with each of heterodimer through their external surfaces via disulfide bonds. The resultant covalent constructs could co-assemble into complementary trimeric hubs, respectively. The two peptide constructs are directly mixed and assembled in solution in order to produce either spherical particles or 2-d plates depending on the solution conditions and kinetic pathway of assembly. In particular, structural changes of the self-assembled peptides are explored by control of the thermal history of the assembly solution.

  14. Innovative Older-Worker Programs.

    Science.gov (United States)

    Jessup, Denise; Greenberg, Barbara

    1989-01-01

    Describes program innovations to keep older workers employed: retraining, job sharing, flexible working hours, job redesign, and phased retirement. Addresses costs and savings, disincentives for workers and employers, and future trends. (SK)

  15. Kinetics of directed self-assembly of block copolymers on chemically patterned substrates

    International Nuclear Information System (INIS)

    Müller, Marcus; Li, Weihua; Rey, Juan Carlos Orozco; Welling, Ulrich

    2015-01-01

    Chemically patterned surfaces have been successfully employed to direct the kinetics of self-assembly of block copolymers into dense, periodic morphologies (”chemoepitaxy”). Significant efforts have been directed towards understanding the kinetics of structure formation and, particularly, the formation and annihilation of defects. In the present manuscript we use computer simulations of a soft, coarse-grained polymer model to study the kinetics of structure formation of lamellar-forming block copolymer thin films on a chemical pattern of lines and spaces. The case where the copolymer material replicates the surface pattern and the more subtle scenario of sparse guiding patterns are considered. Our simulation results highlight (1) the importance of the early stages of pattern-directed self-assembly that template the subsequent morphology and (2) the dependence of the free-energy landscape on the incompatibility between the two blocks of the copolymer. (paper)

  16. Rapid centriole assembly in Naegleria reveals conserved roles for both de novo and mentored assembly.

    Science.gov (United States)

    Fritz-Laylin, Lillian K; Levy, Yaron Y; Levitan, Edward; Chen, Sean; Cande, W Zacheus; Lai, Elaine Y; Fulton, Chandler

    2016-03-01

    Centrioles are eukaryotic organelles whose number and position are critical for cilia formation and mitosis. Many cell types assemble new centrioles next to existing ones ("templated" or mentored assembly). Under certain conditions, centrioles also form without pre-existing centrioles (de novo). The synchronous differentiation of Naegleria amoebae to flagellates represents a unique opportunity to study centriole assembly, as nearly 100% of the population transitions from having no centrioles to having two within minutes. Here, we find that Naegleria forms its first centriole de novo, immediately followed by mentored assembly of the second. We also find both de novo and mentored assembly distributed among all major eukaryote lineages. We therefore propose that both modes are ancestral and have been conserved because they serve complementary roles, with de novo assembly as the default when no pre-existing centriole is available, and mentored assembly allowing precise regulation of number, timing, and location of centriole assembly. © 2016 Wiley Periodicals, Inc.

  17. Next-generation transcriptome assembly

    Energy Technology Data Exchange (ETDEWEB)

    Martin, Jeffrey A.; Wang, Zhong

    2011-09-01

    Transcriptomics studies often rely on partial reference transcriptomes that fail to capture the full catalog of transcripts and their variations. Recent advances in sequencing technologies and assembly algorithms have facilitated the reconstruction of the entire transcriptome by deep RNA sequencing (RNA-seq), even without a reference genome. However, transcriptome assembly from billions of RNA-seq reads, which are often very short, poses a significant informatics challenge. This Review summarizes the recent developments in transcriptome assembly approaches - reference-based, de novo and combined strategies-along with some perspectives on transcriptome assembly in the near future.

  18. All cause mortality and incidence of cancer in workers in bauxite mines and alumina refineries.

    Science.gov (United States)

    Fritschi, Lin; Hoving, Jan Lucas; Sim, Malcolm R; Del Monaco, Anthony; MacFarlane, Ewan; McKenzie, Dean; Benke, Geza; de Klerk, Nicholas

    2008-08-15

    Bauxite is a reddish clay that is refined to produce alumina, which is then reduced to aluminium. There have been studies examining the health of workers in aluminium smelters, but not workers in bauxite mining and alumina refining. A cohort of employees of 1 large aluminium company since 1983 was assembled (n = 6,485, 5,828 men). Deaths and incident cancers to 2002 were ascertained by linkage to national and state cancer and death registries. SIRs and SMRs were calculated compared to national rates standardizing for calendar year, sex and 5-year age group. The mortality from all causes (SMR 0.68, 95% CI: 0.60-0.77), and from circulatory and respiratory diseases, all cancers combined and injury in the male cohort were lower than in the Australian male population and were similar across work groups and with duration of employment. The only significant increased mortality risk was from pleural mesothelioma. The incidence of all cancers combined was similar to the Australian rate. The cohort had a lower risk of incident lymphohaematopoietic cancer (SIR 0.50, 95% CI: 0.31-0.88) and a higher risk of melanoma (SIR 1.30, 95% CI: 1.00-1.69) although no dose-responses were seen. There was also an increased risk of mesothelioma (SIR 3.49, 95% CI: 1.82-6.71), which was associated with exposures outside the aluminium industry. This study is the first to examine cancer and mortality amongst workers in bauxite mines and alumina refineries and found little evidence for increased cancer incidence or mortality in these workers. (c) 2008 Wiley-Liss, Inc.

  19. Motivation and retention of health workers in developing countries: a systematic review

    Directory of Open Access Journals (Sweden)

    Blaauw Duane

    2008-12-01

    Full Text Available Abstract Background A key constraint to achieving the MDGs is the absence of a properly trained and motivated workforce. Loss of clinical staff from low and middle-income countries is crippling already fragile health care systems. Health worker retention is critical for health system performance and a key problem is how best to motivate and retain health workers. The authors undertook a systematic review to consolidate existing evidence on the impact of financial and non-financial incentives on motivation and retention. Methods Four literature databases were searched together with Google Scholar and 'Human Resources for Health' on-line journal. Grey literature studies and informational papers were also captured. The inclusion criteria were: 1 article stated clear reasons for implementing specific motivations to improve health worker motivation and/or reduce medical migration, 2 the intervention recommended can be linked to motivation and 3 the study was conducted in a developing country and 4 the study used primary data. Results Twenty articles met the inclusion criteria. They consisted of a mixture of qualitative and quantitative studies. Seven major motivational themes were identified: financial rewards, career development, continuing education, hospital infrastructure, resource availability, hospital management and recognition/appreciation. There was some evidence to suggest that the use of initiatives to improve motivation had been effective in helping retention. There is less clear evidence on the differential response of different cadres. Conclusion While motivational factors are undoubtedly country specific, financial incentives, career development and management issues are core factors. Nevertheless, financial incentives alone are not enough to motivate health workers. It is clear that recognition is highly influential in health worker motivation and that adequate resources and appropriate infrastructure can improve morale significantly.

  20. Assessing the psychometric properties and the perceived usefulness of the BasisRaadsOnderzoek (BARO as a first-line screening instrument for juvenile offenders

    Directory of Open Access Journals (Sweden)

    van Loosbroek Erik

    2011-06-01

    Full Text Available Abstract Background The aim of this study is to investigate the psychometric properties and the perceived usefulness of the BARO (Dutch: BAsisRaadsOnderzoek; Protection Board Preliminary Examination of Juvenile Suspects. The BARO is a first-line screening instrument for the identification of psychiatric disorders, adverse environmental factors, and levels of (dysfunction in adolescent offenders (age 12 to 18, to be used by social workers of the Child Protection Board (CPB following a police arrest. Method CPB workers administered the BARO to 295 juvenile offenders (91% boys, 9% girls. A subgroup of 66 offenders (89% boys, 11% girls underwent an elaborate diagnostic assessment by forensic psychologists and psychiatrists. Using these assessments the most relevant psychometric properties of the BARO were studied. The perceived usefulness was studied using questionnaires to be filled in by the CPB social workers. Results The internal consistency of the instrument was sufficient to good, the concurrent validity of the CPB social workers applying the BARO and the forensic experts carrying out the comprehensive diagnostic assessment was strong, the discriminatory value of the instrument was moderate to strong, and the perceived usefulness of the instrument was evaluated as good to very good by the majority of the CPB workers. Discussion The BARO has sufficient to good psychometric properties including moderate to strong discriminatory value and is considered a good screening instrument by the CPB social workers. In conclusion, the BARO seems to be a very promising first-line screening instrument to identify psychiatric and psychosocial problems in young offenders.