WorldWideScience

Sample records for asphalt content

  1. Determination of the asphalt content of the asphalt concrete by surface neutron gauge

    International Nuclear Information System (INIS)

    This paper describes the principle, calibration and field detection of determining the asphalt content of asphalt concrete by surface neutron gauge. This method can be utilized to measure the asphalt content for asphalt concrete dams, highways and airport runways to control the engineering quality

  2. A LABORATORY STUDY ON THE EFFECT OF HIGH RAP AND HIGH ASPHALT BINDER CONTENT ON THE PERFORMANCE OF ASPHALT CONCRETE

    OpenAIRE

    Boriack, Paul Christian

    2014-01-01

    This thesis investigates the effect of added asphalt binder content on the performance and volumetric properties of asphalt concrete mixes containing Reclaimed Asphalt Pavement (RAP). Mixes with three different percentages of RAP (0%, 20%, 40%) obtained from an asphalt producer and three different percentages of asphalt binder (design asphalt content, design +0.5%, and design +1.0%) were evaluated. Additionally, a laboratory produced mix containing 100% RAP with four asphalt binder contents...

  3. Effect of Residual Asphalt Content on Creep Strain of Cement Modified Emulsified Asphalt Mixtures

    OpenAIRE

    Seref Oruc; Murat Bostancioglu; Bahadir Yilmaz

    2013-01-01

    Objective of this paper is to determine the rutting performance of residual asphalt content oncement modified emulsified asphalt mixtures at heavy duty highways. For this purpose, emulsified asphaltspecimens with dense graded aggregate were prepared according to Marshall method for emulsified asphaltaggregatecold mixture design. The specimens were prepared in such a way that portland cement wassubstituted for mineral filler in an increased percent from 0 % to 6 %. In this way, three asphalt e...

  4. Nuclear asphalt content gauge study. Research report (Final)

    International Nuclear Information System (INIS)

    This research ascertains if the Troxler Model 3241 Gauge could accurately determine the asphalt content of bituminous-concrete mixtures by nuclear means. The study was divided into three phases. Phase I was conducted in the Central Laboratory where a series of controlled tests were performed for variables that may effect the gauge's asphalt-content determinations. Phase II evolved into a cooperative study between the Maryland State Highway Administration (SHA) and several bituminous concrete producers. Phase III was to report the findings of the study and make a recommendation on the overall practical application of the gauge. The results indicate that the gauge can accurately determine asphalt contents on normal surface and base bituminous mixtures

  5. Evaluation of nuclear asphalt-content gauges. Final report

    International Nuclear Information System (INIS)

    The study evaluated the accuracy and precision of the Troxler, Model 3241-C, and CPN, Model AC-2, Nuclear Asphalt Content Gauges. To achieve precisions at plus or minus 0.15% 95% of the time, it was necessary to establish special procedures for making test samples, controlling environment, and calibration. Both gauges provided acceptable results utilizing a 3-point calibration. Their use in the field would be acceptable when the proper procedures are followed

  6. Laboratory and field evaluation of hot mix asphalt with high contents of reclaimed asphalt pavement

    Science.gov (United States)

    Van Winkle, Clinton Isaac

    Currently in Iowa, the amount of RAP materials allowed for the surface layer is limited to 15% by weight. The objective of this project was to develop quality standards for inclusion of RAP content higher than 15% in asphalt mixtures. To meet Superpave mix design requirements, it was necessary to fractionate the RAP materials. Based on the extensive sieve-by-sieve analysis of RAP materials, the optimum sieve size to fractionate RAP materials was identified. To determine if the higher percentage of RAP materials than 15% can be used in Iowa's state highway, three test sections with 30.0%, 35.5% and 39.2% of RAP materials were constructed on Highway 6 in Iowa City. The construction of the field test sections was monitored and the cores were obtained to measure field densities of test sections. Field mixtures collected from test sections were compacted in the laboratory in order to test the moisture sensitivity using a Hamburg Wheel Tracking Device. The binder was extracted from the field mixtures with varying amounts of RAP materials and tested to determine the effects of RAP materials on the PG grade of a virgin binder. Field cores were taken from the various mix designs to determine the percent density of each test section. A condition survey of the test sections was then performed to evaluate the short-term performance.

  7. Nuclear method for determination of asphalt content corrected for moisture in bituminous mixture. Final report, March 1988-February 1989

    International Nuclear Information System (INIS)

    This report presents results of research on the development of a method for determination of asphalt content corrected for moisture using the nuclear-gauge method. The researchers selected an approach that involved rapid drying of the asphalt concrete samples in a microwave oven prior to the determination of asphalt content using a Troxler Model 3241-C nuclear asphalt-content gauge. As a reference, asphalt contents were also measured using quantitative extraction. In general, good agreement was found between asphalt contents measured by the Troxler Model 3241-C nuclear gauge and asphalt contents measured by quantitative extraction. In extended sampling for Plant 1, no significant increase in nuclear gauge error was seen over a 10-day sampling period, which indicates that daily calibration of the nuclear gauge is probably unnecessary to maintain satisfactory performance. The field demonstration of the procedure of drying the bituminous mixture in a microwave oven and then determining its asphalt content by the nuclear method indicated asphalt-content results were obtained approximately 1 hour faster than results obtained by quantitative extraction

  8. Determination of the bitumen content in asphalt concrete using a neutron reflection method

    International Nuclear Information System (INIS)

    A neutron physical method (reflection method) for the fast, nondestructive determination of the bitumen content in asphalt concrete has been developed. The determination is performed on cylindrical asphalt concrete samples containing desiccated rubble matrix. Using samples of about 1000g and measuring times of 20 min, the reproducibility of the bitumen determination is 0.15 w%, the sensitivity is 3.10-3 g/g. The thus obtained results were compared with data obtained by chemical analysis, using two different type of matrix. The mean values and the standard deviations are in good agreement for both cases. (T.G.)

  9. An optimized setup for determining the bitumen content in asphalt concrete by the neutron reflection method

    International Nuclear Information System (INIS)

    A setup was developed in order to determine the bitumen content in asphalt concrete by neutron reflection. The main parts of this setup are an Am-Be neutron source of 37 GBq and a 3He neutron detector. To avoid geometrical effects of the measurements, the optimum volume of the samples was determined by plotting the reflected neutron response versus the sample volume. For the calibration of the system, the American Standard Method (ASTM) was used when preparing aggregate and asphalt concrete samples. The method was then compared to the conventional chemical method by analyzing unknown samples taken from an asphalt concrete producing plant and finally the method was assessed in terms of reproducibility, sensitivity and precision. (author)

  10. Finite Element Model for Rutting Prediction in Asphalt Mixes in Various Air Void Contents

    OpenAIRE

    Mohammed Hadi Nahi; Ibrahim Kamaruddin; Amiruddin Ismail; Ramez Al-Ezzi Al-Mansob

    2014-01-01

    Asphalt pavement rutting is one of the most commonly observed pavement distresses and is a major safety concern to transportation agencies. Millions of dollars are spent annually to repair rutted asphalt pavements. Researches into improvements of hot-mix asphalt materials mix designs, methods of pavement evaluation and design can provide extended pavement life and significant cost savings in pavement maintenance and rehabilitation. The three objectives of this study are to investigate the rut...

  11. Behavior of asphalt-rubber hot mixes obtained with high crumb rubber contents

    OpenAIRE

    Dantas Neto, Silvrano A.; Farias, Márcio Muniz de; Pais, Jorge C.; Pereira, Paulo A. A.; Santos, Luís Picado

    2003-01-01

    This paper shows the results of a study about the mechanical behavior of dense graded asphalt-rubber hot mixes (grading envelope C of DNER-ES 313/97) prepared with two different types of asphalt-rubber binders. These asphalt-rubber binders were obtained with penetration grade asphalt (AC 50/70) mixed with 21% and 25% of crumb rubber in weight. The rubber was recycled from unserviceable tires using the ambient grinding process. Hot mixes made with the conventional binder AC 5...

  12. A review of asphalt and asphalt mixture aging

    OpenAIRE

    Wilmar Darío Fernández-Gómez; Hugo Alexander Rondón Quintana; Fredy Reyes-Lizcano

    2012-01-01

    This paper presents an extensive review of the pertinent literature regarding asphalt and asphalt mixture Aging. Aging affects flexible pavement performance and is produced by intrinsic and extrinsic variables as well as exposure time. Intrinsic variables include asphalt and aggregate properties, a mixture’s asphalt content, binder film thickness and air void content; extrinsic variables are associated with production (short-term aging) and exposure to environmental field conditions (long-ter...

  13. Effects of Sasobit® content on the rheological characteristics of unaged and aged asphalt binders at high and intermediate temperatures

    Directory of Open Access Journals (Sweden)

    Ali Jamshidi

    2012-08-01

    Full Text Available This paper describes the rheological properties of PG64, PG70, and PG76 asphalt binders blended with different Sasobit® contents. The rheological properties of the Sasobit®-modified binders were characterized after being subjected to different aging conditions using the dynamic shear rheometer (DSR and rotational viscometer (RV according to SuperpaveTM test protocols. The results indicated that the characterization of aging in terms of the Aging Index (AI depends on the rheological property of the asphalt binder selected for use in evaluating aging, the amount of Sasobit®, the binder type, and the temperature range. Linear relationships between failure temperatures of unaged and short-term-aged asphalt were observed for three binder types. Design charts were developed to select the appropriate Sasobit® content as a function of temperature, taking into consideration the stiffening effects of Sasobit®, using the SuperpaveTM fatigue factor and asphalt mix construction temperatures.

  14. Preparation and properties of montmorillonite modified asphalts

    International Nuclear Information System (INIS)

    Modified asphalts were prepared by melt blending with different contents of montmorillonite (MMT) and organomodified montmorillonite (OMMT). The X-ray diffraction (XRD) results show that the MMT modified asphalt may form an intercalated structure, whereas the OMMT modified asphalt may form an exfoliated structure. The addition of MMT and OMMT to asphalt increases both the softening point and viscosity of the modified asphalts at high temperatures. Furthermore, the modified asphalts exhibited higher complex modulus, lower phase angle. As a consequence, the MMT and OMMT modified asphalts displays enhanced viscoelastic properties, which improve its resistance to rutting at high temperatures. Compared with MMT, OMMT showed better effect in improving softening point and rutting resistance of asphalt, which contributes to the formation of exfoliated structure in OMMT modified asphalt. Storage stability tests disclose that the asphalts modified with MMT or OMMT are very stable when montmorillonite content is less than 3 wt%

  15. The Development of Recycling Agent for Asphalt Pavement

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    A type of recycling agent was developed and its use for modifying used asphalt is described.The results show that the viscosity and three main properties of the aged asphalt were remarkably improved.With 5%-7% content of recycling agent, the main properties of recycled asphalt comported with China GB asphalt standard AH-70 and the recycled asphalt concrete could be used as high-grade highway.Furthermore,the recycling mechanism of the aged asphalt is discussed.

  16. Comparative analysis to determine asphalt density and content, using nuclear and traditional methods

    International Nuclear Information System (INIS)

    Quality control for flex pavement construction in Colombia for asphaltic mix, as well as for granular and granular sub base layers is made by means of methods that does not guarantee the quality of the job, due to the difficult execution of tests, which impede more to be done or due to inherent problems of the test process. Thanks to the inherent characteristics and advantages of nuclear techniques, those become the optimal alternative to this quality control job. The present research project has been developed with the objective of justifying the use of new technologies applied to road construction; making a comparative analysis between traditional methods used in our country and nuclear techniques that have been using in United States with great success in quality control in road construction

  17. A review of asphalt and asphalt mixture aging

    Directory of Open Access Journals (Sweden)

    Wilmar Darío Fernández-Gómez

    2012-09-01

    Full Text Available This paper presents an extensive review of the pertinent literature regarding asphalt and asphalt mixture Aging. Aging affects flexible pavement performance and is produced by intrinsic and extrinsic variables as well as exposure time. Intrinsic variables include asphalt and aggregate properties, a mixture’s asphalt content, binder film thickness and air void content; extrinsic variables are associated with production (short-term aging and exposure to environmental field conditions (long-term aging. Taken together, both variables demonstrate that aging results from three distinct mechanisms: volatilisation, oxidation and steric hardening. Temperature, pressure and photo degradation treatments are used to simulate aging in the laboratory and empirical and semi-empirical models are created to represent and study aging. Aging increases asphalt complex modulus and decreases the phase angle. Mixtures become stiffer while fatigue life becomes reduced. Carbonyl and sulfoxide group formation in asphalt are often studied as such chemical changes show oxidation in aged asphalts. The prevailing models used to predict asphalt aging are discussed, though more comprehensive research into asphalt aging is still needed.

  18. Polyurethane synthesis reactions in asphalts

    Energy Technology Data Exchange (ETDEWEB)

    Bukowski, A.; Gretkiewicz, J.

    1982-04-01

    A series of asphalt-polyurethane composites was prepared by means of polyurethane synthesis in asphalt and carried out in melt. The applied materials were asphalts of differentiated group components content, polyester polyols of chain structure from linear to strongly branched, 2,4-tolylene diisocyanate, 4,4-methylenebis(phenyl isocyanate), and tinorganic catalyst. The asphalt components react with isocyanates to a minimal degree. The influence of the applied substrates, temperature, and polyurethane content in the system on the basic kinetic relations characterizing the process is presented. Polyurethane synthesis in asphalts does not differ in a fundamental way from the obtaining of polyurethanes, especially when their content in the composition is significant, 20 wt% and more.

  19. Improved set-up for determination of bitumen content in asphalt concrete by the neutron reflection method

    International Nuclear Information System (INIS)

    A set-up was developed for the determination of bitumen in asphalt concrete by the neutron reflection method. The main parts of this set-up include an Am-Be neutron source (1 Ci) and a 3He neutron detector. To avoid geometrical effects on the measurements, the optimum sample volume was determined from the neutron response vs volume sample plot. The AST method (ASTM) was used for calibration when preparing the aggregate and asphalt concrete samples. The method was compared to the conventional chemical method by analysing unknown samples taken from the asphalt concrete producing plant. The method was characterized by its reproducibility, sensitivity and precision

  20. Effects of Sasobit® content on the rheological characteristics of unaged and aged asphalt binders at high and intermediate temperatures

    OpenAIRE

    Ali Jamshidi; Meor Othman Hamzah; Mohamad Yusri Aman

    2012-01-01

    This paper describes the rheological properties of PG64, PG70, and PG76 asphalt binders blended with different Sasobit® contents. The rheological properties of the Sasobit®-modified binders were characterized after being subjected to different aging conditions using the dynamic shear rheometer (DSR) and rotational viscometer (RV) according to SuperpaveTM test protocols. The results indicated that the characterization of aging in terms of the Aging Index (AI) depends on the rheological propert...

  1. Neutron thermalization in quality control of asphalts content in mixtures for paving. Adaptation of nuclear densimeters for this purpose

    International Nuclear Information System (INIS)

    This paper shows how the neutron source of the nuclear densimeters, used for measure the humidity, can be used for measuring and making the quality control of the asphalt percentage in mixtures used for street paving. The measures are based in the neutronic thermalization processes, because the hydrogen is the main part of chemical composition of the asphalts. A calibration method for the equipment is presented. (author). 6 refs, 3 figs, 3 tabs

  2. Asphalt cement poisoning

    Science.gov (United States)

    Asphalt; Pavement ... The substances in asphalt that can be harmful are: Hydrocarbons Industrial glues Industrial solvents Tar ... Asphalt is found in: Road paving materials Roofing materials Tile cements Asphalt may also be used for ...

  3. Influence of Foamed Asphalt Content and Aggregate Gradation on Mixing Moisture Content of Mixture%泡沫沥青用量和矿料级配对混合料拌和用水量影响

    Institute of Scientific and Technical Information of China (English)

    赵桂娟

    2012-01-01

    为了研究泡沫沥青用量和矿料级配对泡沫沥青混合料所需合理拌和用水量的影响,设计了3种矿料级配组成OA1、OA2和OA3,通过变化4种沥青用量2%、3%、4%、5%(相对于矿料干重的百分比),5种拌和用水量,即混合料最佳击实含水率(OMC)的60%、70%、80%、90%、100%,将各组合下制备成的泡沫沥青混合料成型试件,测定其间接拉伸强度和干密度.结果表明:不同的矿料级配、泡沫沥青用量和拌和用水量条件下制备的泡沫沥青混合料具有不同的间接拉伸强度和干密度.不同的矿料级配和不同的混合料拌和用水量存在最佳泡沫沥青用量3%.综合推荐出泡沫沥青混合料OA1、OA2和OA3适宜的拌和用水量范围分别为65%~80%OMC、70%~85%OMC和75% -85%OMC.通过试验路的铺筑观测发现,使用状况良好,验证了此研究结果是合理的.%The reasonable water consumption of foamed asphalt mixture is influenced by the content of foamed asphalt and mineral aggregate gradation. This paper studied the indirect tensile strength and dry density of foamed asphalt mixture model using three types of mineral aggregate gradation, four different asphalt contents and five kinds of optimum compaction water content. The results show that the foamed asphalt mixture has different indirect tensile strengths and dry densities with various mineral aggregate gradations, foamed asphalt contents and water consumptions. The optimum content of foamed asphalt is determined by 3% according to different gradations and water consumptions of asphalt mixture. The tests indicate that appropriate water consumption ranges are 65% -80%OMC, 70% -85%OMC and 70% -85%OMC for asphalt mixture OA,, OA2 and OA3, respectively. The conclusions are verified by a lot of test results.

  4. The Asphalt Handbook.

    Science.gov (United States)

    Asphalt Inst., College Park, MD.

    The new and completely revised edition of the Asphalt Handbook, a standard reference work in the field of asphalt technology and construction, summarizes with reference the information contained in other Asphalt Institute technical manuals. Major areas discussed include the following--(1) uses of asphalt, (2) terms relating to asphalt and its…

  5. Surface roughness of an asphalt concrete and its mechanical behavior

    OpenAIRE

    MOMM, L; DE LA ROCHE, C; Domingues, A.

    2003-01-01

    The surface roughness of asphalt concrete is studied according to the maximum aggregate size and to the equation of the aggregate graduation curve, on asphalt concrete plates made in laboratory. The macrotexture increases when the maximum aggregate size increases and it decreases when the aggregate fine contents increases. The asphalt concrete structural behaviour is evaluated with rutting, complex modulus and fatigue tests. The study shows stronger mechanical performances on the asphalt conc...

  6. Asphalt Raking. Instructor Manual. Trainee Manual.

    Science.gov (United States)

    Laborers-AGC Education and Training Fund, Pomfret Center, CT.

    This packet consists of the instructor and trainee manuals for an asphalt raking course. The instructor manual contains a course schedule for 4 days of instruction, content outline, and instructor outline. The trainee manual is divided into five sections: safety, asphalt basics, placing methods, repair and patching, and clean-up and maintenance.…

  7. GREENPATCH® - Cold Mix Asphalt

    OpenAIRE

    ECT Team, Purdue

    2013-01-01

    GreenPatch® is environmentally friendly cold asphalt that is a direct replacement for traditional cold patch in repairing asphalt pavements. This revolutionary breakthrough in the cold asphalt industry contains no petroleum based softeners such as diesel, toluene, kerosene, and naphthalene found in conventional cold asphalt that pose serious threats to human health and the environment.

  8. Pitch-asphalts - new binder for road construction

    Energy Technology Data Exchange (ETDEWEB)

    Stompel, Z.; Collin, G.; Szen, A.; Herion, G.

    1988-01-01

    Discusses chemical and physical properties of a mixture of pitches and asphalts produced by the Blachownia Chemical Plant. The mixture consists of coal tar pitches with 25.7% content of toluene-insoluble fractions, anthracene oil and Dex asphalt. The following properties were analyzed: density, softening and softening point, adhesion, viscosity, sedimentation after 14 days. Physical and chemical properties of the pitch-asphalt from Blachownia were compared to those of pitch-asphalt from Ruetgerswerke AG in the FRG. Pitch-asphalt properties were evaluated from the point of view of their use in road construction. 8 refs.

  9. A pulsed-and high resolution-NMR study of the asphalt compositions obtained by the composition analytical method

    International Nuclear Information System (INIS)

    12 Kinds of asphalts were fractionated by the usual composition analytical method to give asphaltenes, maltenes, and waxy substances. Their contents show fairly good relationships with softening temperatures, and 1/T2 values of asphalts. Pulsed- and high resolution-NMR measurements were made of the fractions of 8 asphalts out of 12 asphalts. Asphaltenes from all the asphalts were thought to have almost same structures and characters (T2 asymptotically equals μsec), and their contents vary with the asphalts. Maltenes had no characteristic structures owing to the imperfect fractionation employed in this study, and their content in the asphalt is the largest. (author)

  10. Asbestos Tailings as Aggregates for Asphalt Mixture

    Institute of Scientific and Technical Information of China (English)

    LIU Xinoming; XU Linrong

    2011-01-01

    To use many asbestos tailings collected in Ya-Lu highway, and to explore the feasibility of using asbestos tailings as aggregates in common asphalt mixtures, and properties of some asphalt mixtures were evaluated as well. X-ray diffraction (XRD), X-ray fluorescent (XRF), and atomic absorption spectrophotometry (AAS) were employed to determine the solid waste content of copper, zinc, lead, and cadmium. Volume properties and pavement performances of AC-25 asphalt mixture with asbestos tailings were also evaluated compared with those with basalt as aggregates.XRD and XRF measurement results infer that asbestos tailing is an excellent road material. Volume properties of AC-25 asphalt mixture with asbestos tailings satisfied the related specifications. No heavy metals and toxic pollution were detected in AAS test and the value of pH test is 8.23, which is help to the adhesion with asphalt in the asphalt concrete. When compared with basalt, high temperature property and the resistance to low temperature cracking of AC-25 asphalt mixture was improved by using asbestos tailings as aggregates. In-service AC-25 asphalt pavement with asbestos tailings also presented excellent performance and British Pendulum Number (BPN) coefficient of surface.

  11. Thermal behavior of asphalt cements

    International Nuclear Information System (INIS)

    Asphalt cements are highly complex mixtures of hydrocarbon molecules whose thermal behavior is of prime importance for petroleum and road industry. From DSC, the determination of several thermal properties of asphalts is given, e.g. glass-transition temperature and crystallized fraction content.The dissolution of a pure n-paraffin CnH2n+2 in an asphalt, as seen by DSC, should be a single peak. For 20g of these glasses change with time and temperature. The formation of the crystallized phases is superposed to the enthalpic relaxation of the glasses, making a kinetic study very difficult. (Copyright (c) 1998 Elsevier Science B.V., Amsterdam. All rights reserved.)

  12. Effects of reclaimed asphalt pavement on indirect tensile strength test of foamed asphalt mix tested in dry condition

    International Nuclear Information System (INIS)

    Indirect tensile strength (ITS) test was conducted to analyse strength of the foamed asphalt mixes incorporating reclaimed asphalt pavement. Samples were tested for ITS after cured in the oven at 40°C for 72 hours. This testing condition known as dry condition or unconditioned. Laboratory results show that reclaimed asphalt pavement (RAP) contents insignificantly affect the ITS results. ITS results significantly affected by foamed bitumen contents.

  13. Effects of reclaimed asphalt pavement on indirect tensile strength test of foamed asphalt mix tested in dry condition

    Science.gov (United States)

    Yati Katman, Herda; Rasdan Ibrahim, Mohd; Yazip Matori, Mohd; Norhisham, Shuhairy; Ismail, Norlela

    2013-06-01

    Indirect tensile strength (ITS) test was conducted to analyse strength of the foamed asphalt mixes incorporating reclaimed asphalt pavement. Samples were tested for ITS after cured in the oven at 40°C for 72 hours. This testing condition known as dry condition or unconditioned. Laboratory results show that reclaimed asphalt pavement (RAP) contents insignificantly affect the ITS results. ITS results significantly affected by foamed bitumen contents.

  14. Percolation Model of Graphite-modified Asphalt Concrete

    Institute of Scientific and Technical Information of China (English)

    MO Liantong; WU Shaopeng; LIU Xiaoming; CHEN Zheng

    2005-01-01

    The addition of graphite powder in conventional asphalt mixture can produced asphalt concrete with excellent electrical performance. Percolation theory was employed to discuss the relation between the conductivity and graphite content of graphite-modified asphalt concrete. It was found that the results of percolation model are consistent with experimental values. The percolation threshold of graphite-modified asphalt concrete is 10.94% graphite content account for the total volume of the binder phase consisting of asphalt and graphite. The critical exponent is 3.16, beyond the range of 1.6-2.1 for the standard lattice continuous percolation problem. Its reason is that the tunnel conduction mechanism originates near the critical percent content, which causes this system to be not universal. Tunnel mechanism is demonstrated by the nonlinear voltage-current characteristic near percolation threshold.The percolation model is able to well predict the formation and development of conductive network in graphite-modified asphalt concrete.

  15. An Improvement in Electrical Properties of Asphalt Concrete

    Institute of Scientific and Technical Information of China (English)

    WU Shao-peng; MO Lian-tong; SHUI Zhong-he; XUAN Dong-xing; XUE Yong-jie; YANG Wen-feng

    2002-01-01

    Materials such as Koch AH - 70, basalt aggregate, limestone powder and graphite particles were used to prepare conductive asphalt concrete, which is a new type of multi functional concrete. The mix proportion by weight was shown as follows. Fineaggregates (2.36-4.75 mm):fine aggregates (< 2.36mm): limestone powder: asphalt = 120:240: 14:30. The content of added graphite particles ranged from 0% to 20% ( by the Special weight of asphalt concerte). A conductive asphalt concrete with a resistivity around 10-103·Ωm was obtained.attention was paid to the effects of graphite content, graphite physical-chemical properties, asphalt content and temperature on the resistivity. Furthermore, an attempt was made to develop an electrically conductive model for asphalt concrete.

  16. Low temperature asphalt mixtures

    OpenAIRE

    Modrijan, Damjan

    2006-01-01

    This thesis presents the problem of manufacturing and building in the asphalt mixtures produced by the classical hot procedure and the possibility of manufacturing low temperature asphalt mixtures.We will see the main advantages of low temperature asphalt mixtures prepared with bitumen with organic addition Sasobit and compare it to the classical asphalt mixtures. The advantages and disadvantages of that are valued in the practical example in the conclusion.

  17. Performance of asphalt rubber mixtures

    OpenAIRE

    Thives, Liseane Padilha; Trichês, Glicério; Pereira, Paulo A. A.; Pais, Jorge C.

    2010-01-01

    Asphalt rubber mixtures are one of the most promising techniques to extend the service life of asphalt pavement overlays. Asphalt rubber binder is composed of crumb rubber from reclaimed tires and conventional asphalt. The asphalt rubber binder can be obtained through wet process in two different systems: terminal blending (produced at industrial plants) and continuous blending (produced in asphalt plants). This study presents a laboratory evaluation of asphalt rubber mixtures produced with d...

  18. SGC Tests for Influence of Material Composition on Compaction Characteristic of Asphalt Mixtures

    OpenAIRE

    Qun Chen; Yuzhi Li

    2013-01-01

    Compaction characteristic of the surface layer asphalt mixture (13-type gradation mixture) was studied using Superpave gyratory compactor (SGC) simulative compaction tests. Based on analysis of densification curve of gyratory compaction, influence rules of the contents of mineral aggregates of all sizes and asphalt on compaction characteristic of asphalt mixtures were obtained. SGC Tests show that, for the mixture with a bigger content of asphalt, its density increases faster, that there is a...

  19. Performance of Recycled Porous Hot Mix Asphalt with Gilsonite Additive

    Directory of Open Access Journals (Sweden)

    Ludfi Djakfar

    2015-01-01

    Full Text Available The objective of the study is to evaluate the performance of porous asphalt using waste recycled concrete material and explore the effect of adding Gilsonite to the mixture. As many as 90 Marshall specimens were prepared with varied asphalt content, percentage of Gilsonite as an additive, and proportioned recycled and virgin coarse aggregate. The test includes permeability capability and Marshall characteristics. The results showed that recycled concrete materials seem to have a potential use as aggregate in the hot mix asphalt, particularly on porous hot mix asphalt. Adding Gilsonite at ranges 8–10% improves the Marshall characteristic of the mix, particularly its stability, without decreasing significantly the permeability capability of the mix. The use of recycled materials tends to increase the asphalt content of the mix at about 1 to 2% higher. With stability reaching 750 kg, the hot mix recycled porous asphalt may be suitable for use in the local roads with medium vehicle load.

  20. Road Performance of Fiber Reinforced Asphalt Concrete Bridge Deck Pavement

    OpenAIRE

    Xiu Liu; Zhaojie Sun; Decheng Feng; Yixiang Cao

    2013-01-01

    As the problem of asphalt concrete bridge deck pavement is becoming more and more serious, how to improve its road performance has become the focus of the study. Considering fiber is widely used in road engineering, wheel tracking test, flexural test, immersion marshall test and freeze-thaw splitting test were carried out to study road performance of asphalt mixture with different fiber contents, analyzing the function mechanism of fiber reinforced asphalt ...

  1. Use of scrap rubber in asphalt pavement surfaces

    Science.gov (United States)

    Eaton, Robert A.; Roberts, Richard J.; Blackburn, Robert R.

    1991-12-01

    Scrap tire rubber was mixed into an asphalt concrete wearing course to study the effect of ice disbonding from the pavement surface under traffic. Rubber contents of 0, 3, 6, and 12 percent by weight were studied. Initial laboratory ice disbonding test results led to the development of a new paving material, Chunk Rubber Asphalt Concrete (CRAC), that uses larger pieces of rubber in a much denser asphalt concrete mix. Strength values doubled and ice disbonding performance was enhanced.

  2. Operational properties of nanomodified stone mastic asphalt

    Directory of Open Access Journals (Sweden)

    Inozemtsev Sergey Sergeevich

    2015-03-01

    Full Text Available In order to prolong the lifetime and to improve the quality of pavements made of asphalt concrete it is necessary to apply innovative solutions in the process of design of such building materials. In order to solve the problem of low durability of asphalt concrete a modifier was proposed, which consists of diatomite, iron hydroxide sol (III and silica sol. Application of the diatomite with nanoscale layer of nanomodifier allows getting a stone mastic asphalt, which has high values of physical and mechanical properties and allows refusing from expensive stabilizing additive. Mineral filler was replaced by diatomite, which has been modified by iron hydroxide sol (III and silica sol. Modified diatomite allows sorption of bitumen and increase the cohesive strength and resistance to shear at positive temperatures. The modified asphalt has higher resistance to rutting at high temperature, abrasion resistance at low temperature and impact of climatic factors: alternate freezing and thawing, wetting-drying, UV and IR radiations. It is achieved by formation of solid and dense bitumen film at the phase interface and controlling the content of light fractions of the bitumen. The modifier consists of sol of iron hydroxide, which blocks the oxidation and polymerization of bitumen during operation. The proposed material allows controlling the initial structure formation of stone mastic asphalt. It was shown that modern test methods allow assessing the durability of asphalt in the design phase compositions.

  3. Study on Producing Heavy Paving Asphalt

    Institute of Scientific and Technical Information of China (English)

    Liu Daosheng; Gao Zhirong; Huo Kaifu; Liao Kejian

    2002-01-01

    The highly viscous crude oil from Shuguang No. 1 zone of Liaohe oilfield features high density,high viscosity and low wax content. It contains no gasoline fraction and its diesel oil fraction yield is only 7.19%, which belongs to the low sulfur naphthenic stocks crude oil. Its heavy fraction is not suited for producing lubricating oil. Its heavy oil, which contains more resins and asphaltenes and less wax, is not an ideal feedstock for catalytic cracking, but is the ideal raw material for producing high-grade paving asphalt.Now this highly viscous crude oil is used as fuel oil after being emulsified in Liaohe oilfield, but its viscosity is so high that it cannot be atomized uniformly and burned completely, resulting not only in waste of oil resource but also in reduction of economical benefit. To make full use of this oil resource and alleviate the shortfall of high grade paving asphalt in China, various brands of asphalt meeting Q/SHR003-1998and ESSO specifications were developed by blending vacuum residue of the said oil and a blending component which are rich in aromatics and deficient in wax. The impact of blending component on properties of blended asphalt has been investigated and road performances of these blended asphalts were studied. The laboratory test results show that the blended asphalts have good road performance and antiaging property.

  4. Replacement of asphalt in glass-mat roofing shingles. Final report, March 1980-March 1982

    Energy Technology Data Exchange (ETDEWEB)

    Bastian, E.J. Jr.; McCandlish, E.F.K.; Sieling, F.W.

    1982-05-01

    Up to 50% of the asphalt now used in glass-mat shingles may be replaceable by increasing the mineral filler content and/or extending the asphalt with elemental sulfur. Highly filled, lab-made shingles containing asphalt flux perform acceptably in fire tests, slide tests, blister tests, granule adhesion, and freeze-thaw cracking tests. They have high stain and scuff potential and are too limp for convenient application around 110/sup 0/F. Lab-made shingles containing asphalt saturant are satisfactory in most respects, but they are still too limp for high temperature application. Various methods to stiffen highly filled shingles were tried. The most promising method is the use of two lightweight glass mats, laminated together with asphalt. Shingles made in this way have handling properties superior to conventional shingles and are economically feasible. In the area of replacement of asphalt with sulfur, five small-scale plant trials produced shingles which, after a year of outdoor exposure, are satisfactory. On the basis of preliminary measurements, no important difference in tensile or flexural properties between asphalt and sulfur/asphalt shingles is expected. In Weather-Ometer tests, sulfur/asphalt tends to have lower durability than conventional coating. This is confirmed by outside weathering of sulfur/asphalt films. By choosing the correct asphalt softening point and correct filler level, sulfur/asphalt/filler can have equal durability to conventional asphalt/filler combinations.

  5. Asphalt rubber mixtures in Portugal: fatigue resistance

    OpenAIRE

    Miranda, Henrique; Batista, Fátima; Neves, José; Antunes, Maria de Lurdes; Fonseca, Paulo

    2009-01-01

    This paper presents a study concerning the fatigue behaviour of asphalt mixtures with bitumen modified with high content of crumb rubber used in Portugal. For assessing the fatigue behaviour of this type of mixtures, four asphalt mixtures with high content of crumb rubber were used: two field bituminous mixtures – an open-graded and a gap-graded – both with granite aggregates; and two laboratory manufactured bituminous mixtures – an open-graded mixture with granite aggregates and a gap-graded...

  6. Asphalt in Pavement Maintenance.

    Science.gov (United States)

    Asphalt Inst., College Park, MD.

    Maintenance methods that can be used equally well in all regions of the country have been developed for the use of asphalt in pavement maintenance. Specific information covering methods, equipment and terminology that applies to the use of asphalt in the maintenance of all types of pavement structures, including shoulders, is provided. In many…

  7. Performance Evaluation of Stone Mastic Asphalt and Hot Mix Asphalt Mixtures Containing Recycled Concrete Aggregate

    Directory of Open Access Journals (Sweden)

    Mohammad Saeed Pourtahmasb

    2014-01-01

    Full Text Available Environmental and economic considerations have encouraged civil engineers to find ways to reuse recycled materials in new constructions. The current paper presents an experimental research on the possibility of utilizing recycled concrete aggregates (RCA in stone mastic asphalt (SMA and hot mix asphalt (HMA mixtures. Three categories of RCA in various percentages were mixed with virgin granite aggregates to produce SMA and HMA specimens. The obtained results indicated that, regardless of the RCA particular sizes, the use of RCA to replace virgin aggregates increased the needed binder content in the asphalt mixtures. Moreover, it was found that even though the volumetric and mechanical properties of the asphalt mixtures are highly affected by the sizes and percentages of the RCA but, based on the demands of the project and traffic volume, utilizing specific amounts of RCA in both types of mixtures could easily satisfy the standard requirements.

  8. Test of Microstructur Permeable Asphalt Pavement Used Domato Stone (Quarsite Dolomite) As Course Agregate for Surface Layer of Road Pavement

    OpenAIRE

    Firdaus Chairuddin; Wihardi Tjaronge

    2014-01-01

    The experiment works was dividing into two phases, for phase one was developed to investigate the properties of aggregates and straight asphalt qualities. The experiment work for phase two was developed to design the porous asphalt mix. In this phase Japan’s method and Binamarga’s method was used to define optimum asphalt content. In this phase, has result cantabro loss weight 77.10 for asphalt quality 3% and loss weight 9.70 for asphalt quality 5%. asphalt flow down, air void ...

  9. Hot Mix Asphalt Recycling: Practices and Principles

    OpenAIRE

    Mohajeri, M.

    2015-01-01

    Hot mix asphalt recycling has become common practice all over the world since the 1970s because of the crisis in oil prices. In the Netherlands, hot recycling has advanced to such an extent that in most of the mixtures more than 50% of reclaimed asphalt (RA) is allowed. These mixtures with such a high RA content are produced in a batch plant to which a parallel drum is attached. In this drum RA is pre-heated to approximately 130°C. Since 2007 another hot mix recycling techniques became availa...

  10. Laboratory performance of asphalt rubber mixtures

    OpenAIRE

    Fontes, Liseane; Trichês, Glicério; Pais, Jorge; Pereira, Paulo; Minhoto, Manuel

    2009-01-01

    Asphalt rubber mixtures are one of the most promising techniques to extend the service life of asphalt pavement overlays. Asphalt rubber binder is composed of crumb rubber from reclaimed tires and conventional asphalt. The asphalt rubber binder can be obtained through wet process in two different systems: tire rubber modified asphalt binder (produced at industrial plants) and continuous blending (produced in asphalt plants). This study presents a laboratory evaluation of asphalt rubber mixtur...

  11. High Modulus Asphalt Concrete with Dolomite Aggregates

    Science.gov (United States)

    Haritonovs, V.; Tihonovs, J.; Smirnovs, J.

    2015-11-01

    Dolomite is one of the most widely available sedimentary rocks in the territory of Latvia. Dolomite quarries contain about 1,000 million tons of this material. However, according to Latvian Road Specifications, this dolomite cannot be used for average and high intensity roads because of its low quality, mainly, its LA index (The Los Angeles abrasion test). Therefore, mostly the imported magmatic rocks (granite, diabase, gabbro, basalt) or imported dolomite are used, which makes asphalt expensive. However, practical experience shows that even with these high quality materials roads exhibit rutting, fatigue, and thermal cracks. The aim of the research is to develop a high performance asphalt concrete for base and binder courses using only locally available aggregates. In order to achieve resistance against deformations at a high ambient temperature, a hard grade binder was used. Workability, fatigue and thermal cracking resistance, as well as sufficient water resistance is achieved by low porosity (3-5%) and higher binder content compared to traditional asphalt mixtures. The design of the asphalt includes a combination of empirical and performance based tests, which in laboratory circumstances allow simulating traffic and environmental loads. High performance AC 16 base asphalt concrete was created using local dolomite aggregate with polymer modified (PMB 10/40-65) and hard grade (B20/30) bitumen. The mixtures were specified based on fundamental properties in accordance with EN 13108-1 standard.

  12. About Coloured Cold Asphaltic Mixtures

    Directory of Open Access Journals (Sweden)

    Loredana Judele

    2008-01-01

    Full Text Available The first coloured bitumen was obtained by using bitumen from Peru and then bitumen from the Middle East, with a low content of asphaltenes, also called "colourable" bitumens. The colours obtained by adding iron oxides led nevertheless to dark colours, due to the presence of asphaltenes. Nowadays the coloured asphalt is obtained from synthesis binders with translucent aspect. The colours are obtained by adding inorganic pigments, mainly iron oxide for red, chromic oxide for green, titanic dioxide for white. The properties and behaviour of the coloured bitumen during its lifetime are comparable with the ones of classic bitumen, sometimes even better.

  13. Asphalt chemical fractionation

    International Nuclear Information System (INIS)

    Asphalt fractionation were carried out in the Esmeraldas Oil Refinery using n-pentane, SiO2 and different mixture of benzene- methane. The fractions obtained were analyzed by Fourier's Transformed Infrared Spectrophotometry (FTIR)

  14. Modified Asphalt Binder with Natural Zeolite for Warm Mix Asphalt

    Science.gov (United States)

    Dubravský, Marián; Mandula, Ján

    2015-11-01

    In recent years, warm mix asphalt (WMA) is becoming more and more used in the asphalt industry. WMA provide a whole range of benefits, whether economic, environmental and ecological. Lower energy consumption and less pollution is the most advantages of this asphalt mixture. The paper deals with the addition of natural zeolite into the sub base asphalt layers, which is the essential constituent in the construction of the road. Measurement is focused on basic physic - mechanical properties declared according to the catalog data sheets. The aim of this article is to demonstrate the ability of addition the natural zeolite into the all asphalt layers of asphalt pavement. All asphalt mixtures were compared with reference asphalt mixture, which was prepared in reference temperature.

  15. Multiscale Constitutive Modeling of Asphalt Concrete

    Science.gov (United States)

    Underwood, Benjamin Shane

    Multiscale modeling of asphalt concrete has become a popular technique for gaining improved insight into the physical mechanisms that affect the material's behavior and ultimately its performance. This type of modeling considers asphalt concrete, not as a homogeneous mass, but rather as an assemblage of materials at different characteristic length scales. For proper modeling these characteristic scales should be functionally definable and should have known properties. Thus far, research in this area has not focused significant attention on functionally defining what the characteristic scales within asphalt concrete should be. Instead, many have made assumptions on the characteristic scales and even the characteristic behaviors of these scales with little to no support. This research addresses these shortcomings by directly evaluating the microstructure of the material and uses these results to create materials of different characteristic length scales as they exist within the asphalt concrete mixture. The objectives of this work are to; 1) develop mechanistic models for the linear viscoelastic (LVE) and damage behaviors in asphalt concrete at different length scales and 2) develop a mechanistic, mechanistic/empirical, or phenomenological formulation to link the different length scales into a model capable of predicting the effects of microstructural changes on the linear viscoelastic behaviors of asphalt concrete mixture, e.g., a microstructure association model for asphalt concrete mixture. Through the microstructural study it is found that asphalt concrete mixture can be considered as a build-up of three different phases; asphalt mastic, fine aggregate matrix (FAM), and finally the coarse aggregate particles. The asphalt mastic is found to exist as a homogenous material throughout the mixture and FAM, and the filler content within this material is consistent with the volumetric averaged concentration, which can be calculated from the job mix formula. It is also

  16. Modified Asphalt Binder with Natural Zeolite for Warm Mix Asphalt

    OpenAIRE

    Dubravský Marián; Mandula Ján

    2015-01-01

    In recent years, warm mix asphalt (WMA) is becoming more and more used in the asphalt industry. WMA provide a whole range of benefits, whether economic, environmental and ecological. Lower energy consumption and less pollution is the most advantages of this asphalt mixture. The paper deals with the addition of natural zeolite into the sub base asphalt layers, which is the essential constituent in the construction of the road. Measurement is focused on basic physic – mechanical properties decl...

  17. Influence of conductive additive on temperature susceptibility of asphalt binders

    Institute of Scientific and Technical Information of China (English)

    吴少鹏; 李波; 陈筝; 黄旭

    2008-01-01

    The effects of graphite on temperature susceptibility of asphalt binders were investigated by penetration test,Ring & Ball softening point test and viscosity test.And penetration index(IP),viscosity-temperature susceptibility(SVT),and penetration-viscosity numbers(NPV) were introduced to evaluate the effects.The results show that the penetration,softening point and viscosity of asphalt binder increase with the increase of content of graphite.This means that the addition of graphite makes asphalts stiffer.The results from IP,NPV and SVT show that temperature susceptibility is reduced by the addition of graphite.

  18. Performance of Recycled Porous Hot Mix Asphalt with Gilsonite Additive

    OpenAIRE

    Ludfi Djakfar; Hendi Bowoputro; Bangun Prawiro; Nugraha Tarigan

    2015-01-01

    The objective of the study is to evaluate the performance of porous asphalt using waste recycled concrete material and explore the effect of adding Gilsonite to the mixture. As many as 90 Marshall specimens were prepared with varied asphalt content, percentage of Gilsonite as an additive, and proportioned recycled and virgin coarse aggregate. The test includes permeability capability and Marshall characteristics. The results showed that recycled concrete materials seem to have a potential...

  19. Modified rubberized stone matrix asphalt for Nineveh roads

    Institute of Scientific and Technical Information of China (English)

    Al-Hadidy AI; TAN Yi-qiu

    2008-01-01

    To evaluate the effects of Crumb Rubber Modifiers (CRMS) on basic engineering properties (i. e.Marshall, tensile strength, and compressive strength) of stone matrix asphalt mixtures, the ASTM testing and procedures were employed. Results of the evaluation were used to quantify the effect of CRM source and CRM content on engineering properties at testing temperatures of 25℃and 60℃. Statistical models were developed, which represent the nature of effects on performance-related properties of stone matrix asphalt mixtures.

  20. DURABILITY OF ASPHALT CONCRETE MIXTURES USING DOLOMITE AGGREGATES

    Directory of Open Access Journals (Sweden)

    Imad Al-Shalout

    2015-12-01

    Full Text Available This study deals with the durability of asphalt concrete, including the effects of different gradations, compaction temperatures and immersion time on the durability potential of mixtures. The specific objectives of this study are: to investigate the effect of compaction temperature on the mechanical properties of asphalt concrete mixtures; investigate the effect of bitumen content and different aggregate gradations on the durability potential of bituminous mixtures.

  1. SGC Tests for Influence of Material Composition on Compaction Characteristic of Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Qun Chen

    2013-01-01

    Full Text Available Compaction characteristic of the surface layer asphalt mixture (13-type gradation mixture was studied using Superpave gyratory compactor (SGC simulative compaction tests. Based on analysis of densification curve of gyratory compaction, influence rules of the contents of mineral aggregates of all sizes and asphalt on compaction characteristic of asphalt mixtures were obtained. SGC Tests show that, for the mixture with a bigger content of asphalt, its density increases faster, that there is an optimal amount of fine aggregates for optimal compaction and that an appropriate amount of mineral powder will improve workability of mixtures, but overmuch mineral powder will make mixtures dry and hard. Conclusions based on SGC tests can provide basis for how to adjust material composition for improving compaction performance of asphalt mixtures, and for the designed asphalt mixture, its compaction performance can be predicted through these conclusions, which also contributes to the choice of compaction schemes.

  2. SGC tests for influence of material composition on compaction characteristic of asphalt mixtures.

    Science.gov (United States)

    Chen, Qun; Li, Yuzhi

    2013-01-01

    Compaction characteristic of the surface layer asphalt mixture (13-type gradation mixture) was studied using Superpave gyratory compactor (SGC) simulative compaction tests. Based on analysis of densification curve of gyratory compaction, influence rules of the contents of mineral aggregates of all sizes and asphalt on compaction characteristic of asphalt mixtures were obtained. SGC Tests show that, for the mixture with a bigger content of asphalt, its density increases faster, that there is an optimal amount of fine aggregates for optimal compaction and that an appropriate amount of mineral powder will improve workability of mixtures, but overmuch mineral powder will make mixtures dry and hard. Conclusions based on SGC tests can provide basis for how to adjust material composition for improving compaction performance of asphalt mixtures, and for the designed asphalt mixture, its compaction performance can be predicted through these conclusions, which also contributes to the choice of compaction schemes. PMID:23818830

  3. Analysis of asphalt mixtures on town roads

    OpenAIRE

    Glavica, Primož

    2006-01-01

    Asphalt mixtures are most commonly used composite for construction of top layers of different drive ways. By definition asphalt mixtures are composed of crushed rock, fill, bitumen and additives. Percentage of individual components wary according to the purpose asphalt mixture is to be used for. Asphalt mixtures must be capable of enduring different types of load. According to the type of load asphalt mixtures are divided into asphalt mixtures used for supporting layers and asp...

  4. Utilization of recycled asphalt concrete with warm mix asphalt and cost-benefit analysis.

    Science.gov (United States)

    Oner, Julide; Sengoz, Burak

    2015-01-01

    The asphalt paving industries are faced with two major problems. These two important challenges are generated with an increase in demand for environmentally friendly paving mixtures and the problem of rapidly rising raw materials. Recycling of reclaimed asphalt pavement (RAP) is a critical necessity to save precious aggregates and reduce the use of costly bitumen. Warm Mix Asphalt (WMA) technology provides not only the option of recycling asphalt pavement at a lower temperature than the temperature maintained in hot mixtures but also encourages the utilization of RAP and therefore saves energy and money. This paper describes the feasibility of utilizing three different WMA additives (organic, chemical and water containing) at recommended contents with different percentages of RAP. The mechanical properties and cost-benefit analysis of WMA containing RAP have been performed and compared with WMA without RAP. The results indicated that, 30%, 10% and 20% can be accepted as an optimum RAP addition related to organic, chemical and water containing additives respectively and organic additive with 30% RAP content has an appreciable increase in tensile strength over the control mix. It was also concluded that the RAP with WMA technology is the ability to reduce final cost compared to HMA and WMA mixtures. PMID:25574851

  5. Experimental evaluation on high temperature rheological properties of various fiber modified asphalt binders

    Institute of Scientific and Technical Information of China (English)

    陈筝; 吴少鹏; 朱祖煌; 刘杰胜

    2008-01-01

    High temperature rheological properties of fiber modified asphalt binders and impact of the type and content on such properties were studied.Three types of fiber,including polyester(PET),polyacrylonitrile(PAN) and cellulose(CEL),a control content(0%) and four levels of fiber content(2%,4%,6% and 8% by total asphalt binder mass) were used with asphalt binders.The high temperature rheological properties,consisting of complex modulus(G*) and phase angle δ,were measured using SHRP’s dynamic shear rheometer(DSR) between 46-82 ℃.Experimental results indicate that the changes of G* and tan δ of fiber modified asphalt binders with the increase of test temperature tend to slow down,and the temperature susceptibility is improved obviously compared to that of original asphalt binder.Fiber modification results in the increase of rutting parameter(G*/sin δ) at high temperatures,the decrease of temperature susceptibility,and further improved high temperature performance of asphalt binder.An excellent correlation exhibits between fiber content and high temperature performance of asphalt binder.Moreover,fiber type also has different influences on the improvement of G*/sin δ,G*/sin δ of PET and PAN fiber asphalt binders are both higher than that of CEL fiber,but G*/sin δ of CEL fiber is still higher than that of original asphalt.However,there is a critical fiber content when fibers start to interact with each other.Therefore,based on the critical fiber content and economic consideration,the optimum fiber contents for various fiber-modified asphalt binders are obtained.

  6. Test of Microstructur Permeable Asphalt Pavement Used Domato Stone (Quarsite Dolomite As Course Agregate for Surface Layer of Road Pavement

    Directory of Open Access Journals (Sweden)

    Firdaus Chairuddin

    2014-06-01

    Full Text Available The experiment works was dividing into two phases, for phase one was developed to investigate the properties of aggregates and straight asphalt qualities. The experiment work for phase two was developed to design the porous asphalt mix. In this phase Japan’s method and Binamarga’s method was used to define optimum asphalt content. In this phase, has result cantabro loss weight 77.10 for asphalt quality 3% and loss weight 9.70 for asphalt quality 5%. asphalt flow down, air void and density values. The experiment work for phase two was developed to investigate the qualities of porous asphalt. In this phase, wheel tracking machine test was used to investigate the dynamic stability of mixes.

  7. Polymer Blends Modified Asphalt

    Institute of Scientific and Technical Information of China (English)

    WANG YunPu; LI YuFeng; GAO XiaoHui; WANG RongMin

    2001-01-01

    @@ Asphalt is an important low-cost thermo-plastic material which is widely used for construction, in particular as road-paving. Therefore it is exposed to a wide range of load and weather conditions. Increasing traffic factors, such as heavier loads, higher traffic volume and higher tire pressure demand higher performance pavements. However, this kind of materials does not have good mechanical properties because it is hard and brittle in cold weather, and soft and fluid in a hot environment.

  8. 橡胶粉掺量对胶粉改性沥青混合料高温性能的影响研究%The impact study of rubber powder content on rubber powder modiifed asphalt mixture high temperature performance

    Institute of Scientific and Technical Information of China (English)

    黄卫东; 高磊; 施晓强

    2014-01-01

    为分析橡胶粉掺量对胶粉改性沥青混合料高温性能的影响,本文选取五种掺量(15%、18%、21%、24%及27%,内掺)对基质沥青分别改性,对其成型的橡胶沥青混合料进行车辙试验和静态蠕变试验以评价掺量对高温性能的影响,设计级配为AR-AC13。试验结果表明,随着橡胶粉掺量的增加,橡胶沥青混合料高温性能先提高后下降,在掺量为24%时达到最佳。%For the analysis of rubber powder content on the influence of the high temperature performance of rubber powder modified asphalt mixture, this article selected five content (15%, 18%, 21%, 24%and 18%) rubber powder to modified matrix asphalt respectively, then rutting test and static creep test were carried of five different rubber asphalt mixture to assess properties of high temperature, the design gradation of mixtures was AR-AC13.The test results showed that with the increase of rubber powder content, the high temperature performance of rubber asphalt mixture was enhanced first and then dropped after, when content is 24%, the high temperature performance was best.

  9. Modeling Recycling Asphalt Pavement Processing Technologies in Asphalt Mixing Plants

    OpenAIRE

    Simonas Tamaliūnas; Henrikas Sivilevičius

    2011-01-01

    The article presents reclaimed asphalt pavement (RAP) processing technologies and equipment models used in the asphalt mixing plant (AMP). The schematic model indicating all possible ways to process RAP in AMP is shown. The model calculating the needed temperature of mineral materials used for heating RAP is given and an example of such calculation is provided.Article in Lithuanian

  10. Performance prediction of hot mix asphalt from asphalt binders

    International Nuclear Information System (INIS)

    Asphalt binder being a high weight hydrocarbon contains asphaltene and maltene and is widely used as cementing materials in the construction of flexible pavements. Its performance in hot mix asphalt also depends on combining with different proportions of aggregates. The main objective of this study was to characterize asphalt cement rheological behavior and to investigate the influence of asphalt on asphalt-aggregate mixtures prepared with virgin binders and using polymers. Binder rheology and mixtures stiffness were determined under a range of cyclic loadings and temperature conditions. Master curves were developed for the evaluation of relationship between parameters like complex modulus and phase angle at different frequencies. Horizontal shift factors were also computed to determine time and temperature response of binders and mixes. The results showed that the stiffness of both the binder and the mixes depends on temperature and frequency of load. Polymer modified binder is least susceptible to temperature variations as compared to other virgin asphalt cement. Performance of asphalt mixtures can be predicted from those of asphalt binders using the master curve technique. (author)

  11. Evaluation of Warm Mix Asphalt Technologies and Recycled Asphalt Pavements in Truckee Meadows, Nevada

    Science.gov (United States)

    Diaz Montecino, Cristian

    This study evaluated the properties and laboratory-performance of Hot Mix Asphalt (HMA) and Warm Mix Asphalt (WMA) mixtures with different levels of Recycled Asphalt Pavements (RAP) content: none for control mixtures, around 15% by dry weight of aggregates, and more than 30% by dry weight of aggregates. The rheological properties were evaluated for virgin and recovered RAP asphalt binders. The target amount of RAP in the mixtures was determined by using Blending Charts and Mortar Experiments. The mixtures are design through the guidelines established in Marshall Mix Design Method considering additional modifications for RAP and WMA from Superpave Mix Design. The mixtures are evaluated for their resistance to moisture damage by means of measuring the Dynamic Modulus |E*| after three freeze/thaw cycles and the indirect tensile strength after one and three freeze/thaw cycles. The resistance of the mixtures to permanent deformation was also evaluated by using the Asphalt Mixture Performance Tester (AMPT) to measure the flow number (FN). For this study, it was determined that the resistance to moisture damage decreases as the number of freeze/thaw cycles increases for most of the evaluated mixtures. Mixtures exhibited an increase in dynamic modulus as the RAP percentage increased. A decrease in the resistance to moisture damage was detected with the increase in RAP content for most of the mixtures. HMA mixtures exhibited a better performance in rutting than the WMA mixtures. An increase in rutting resistance was observed with the increase in RAP percentage for HMA mixtures whereas an inconsistent trend was observed for WMA mixtures. Further study is needed to validate the use of the high percentage of RAP in Washoe County.

  12. Preparation, Characterization and Hot Storage Stability of Asphalt Modified by Waste Polyethylene Packaging

    Institute of Scientific and Technical Information of China (English)

    Changqing Fang; Ying Zhang; Qian yu; Xing Zhou; Dagang Guo; Ruien Yu; Min Zhang

    2013-01-01

    Waste polyethylene packaging (WPE) was used to modify asphalt,and hot storage stability of the modified asphalt was studied in this paper.The morphological change and component loss of WPE modified asphalt were characterized by fluorescence microscopy,Fourier transform infrared spectroscopy (FT-IR),differential scanning calorimetry (DSC),thermogravimetry (TG) and isolation testing.In addition,the mechanism of the hot storage stability of WPE modified asphalt was discussed.The results showed that the modification of asphalt with WPE was a physical process.It was found that the filament or partly network-like structure formed in the modified asphalt system was beneficial to improving the hot storage stability.Moreover,the addition of WPE resulted in a decrease in both the light components volatilization and the macromolecules decomposition of asphalt.It was demonstrated that when the content of WPE in matrix asphalt was less than 10 wt%,the service performances of modified asphalt could be better.

  13. The Silurian Reservoir Bed—Differentiated Asphalts in Tarim Basin and Modeling Experiments on Their Origin

    Institute of Scientific and Technical Information of China (English)

    刘洛夫; 刘宏江; 等

    2002-01-01

    There is a type of asphalt that originated from differentiation from reservoir bed (named reservoir bed-differentiated asphalt)in the Silurian asphaltic sandstones of the Tarim Basin.These asphalts are the result of second-time charging of hydrocarbons into the Silurian reservoir,which were derived from Lower Paleozoic source rocks.Asphalt was differentiated from the reservoir bed in the hydrocarbon gathering area of secondary migration.The different-tiation is caused by changes in reservoir physical properties when pearl or chain hydrocarbons migrating through and gathering in the reservoir bed,and light components are lost and heavy ones are involved in the formation of asphalt or heavy oil.There are two kinds of occurrence of these asphalts in the Silurian system of the Tarim Basin.One is the poor heavy oil layer with lower oil saturation in trap and the other is scattered hydrocarbon distributed along the trans-port layer and unconformity surface.Reservoir bed-differentiated asphalts have two characteris-tics:total hydrocarbon content is high in extractable organic matter and the ratio of saturated to aromatic hydrocarbon is usually greater than unity.The physically modeling experiment has confirmed these characteristics and the genesis of the reservoir bed-differentiated asphalts.

  14. The Silurian Reservoir Bed-Differentiated Asphalts in Tarim Basin and Modeling Experiments on Their Origin

    Institute of Scientific and Technical Information of China (English)

    刘洛夫; 刘宏江; 王洪玉; 曾溅辉

    2002-01-01

    There is a type of asphalt that originated from differentiation from reservoir bed (named reservoir bed-differentiated asphalt) in the Silurian asphaltic sandstones of the Tarim Basin. These asphalts are the result of second-time charging of hydrocarbons into the Silurian reservoir, which were derived from Lower Paleozoic source rocks. Asphalt was differentiated from the reservoir bed in the hydrocarbon gathering area of secondary migration. The differen tiation is caused by changes in reservoir physical properties when pearl or chain hydrocarbons migrating through and gathering in the reservoir bed, and light components are lost and heavy ones are involved in the formation of asphalt or heavy oil. There are two kinds of occurrence of these asphalts in the Silurian system of the Tarim Basin. One is the poor heavy oil layer with lower oil saturation in trap and the other is scattered hydrocarbon distributed along the transport layer and unconformity surface. Reservoir bed-differentiated asphalts have two characteristics: total hydrocarbon content is high in extractable organic matter and the ratio of saturated to aromatic hydrocarbon is usually greater than unity. The physically modeling experiment has confirmed these characteristics and the genesis of the reservoir bed-differentiated asphalts.

  15. Stiffness of Hot-Mix Asphalt

    OpenAIRE

    Pellinen, Terhi K.; Xiao, Shangzhi

    2006-01-01

    This research was initiated from a need to evaluate marginal mixtures that do not meet the Superpave mix design criteria for the air voids content requirements for the construction of hot mix asphalt pavements. The developed criteria is comprised of the base criteria derived from test data of as-placed field cores normalized to 7.5% air voids content, which provides the minimum stiffness and strength requirements for a mixture as a function of the traffic level. The stiffness of pavement core...

  16. Feasibility of using 100% Recycled Asphalt Pavement mixtures for road construction

    Science.gov (United States)

    Carlson, Russell Edgar, IV

    Recycled Asphalt Pavement (RAP) is the largest recycled good in the United States and 80 million tons are recycled yearly, saving taxpayers about $1.5 billion dollars. This paper explores the possibility of utilizing 100% RAP materials in asphalt pavement. Asphalt mixtures are produced at 135°C in a typical asphalt plant. However, at 135°C, not all binder from RAP materials may not become effective for coating aggregates. The main objective of the study is to determine the amount of effective binder available from RAP in the asphalt plant. The 100% RAP mixes have aged binder that can alter mix designs and interaction with virgin binder. In this study, to determine low temperature cracking resistance and fatigue performance, samples were prepared using a 100% RAP mix with no virgin binder and a 100% RAP mix with virgin asphalt binder to achieve the optimum binder content of the mix. Second, to determine the effectiveness of binder from RAP materials, compaction tests were performed by heating RAP materials at various temperatures. It was found that 100% RAP mixes cannot be feasible for field use if additional virgin binder is added to reach the optimum asphalt content. Based on limited test results, the low temperature grade was not within proper limits but the beam fatigue testing results were acceptable. Based on compaction test results, additional heating is needed to increase the effectiveness of asphalt binder from RAP materials.

  17. Polymer Blends Modified Asphalt

    Institute of Scientific and Technical Information of China (English)

    WANG; YunPu

    2001-01-01

    Asphalt is an important low-cost thermo-plastic material which is widely used for construction, in particular as road-paving. Therefore it is exposed to a wide range of load and weather conditions. Increasing traffic factors, such as heavier loads, higher traffic volume and higher tire pressure demand higher performance pavements. However, this kind of materials does not have good mechanical properties because it is hard and brittle in cold weather, and soft and fluid in a hot environment.  ……

  18. Gray Correlation Analysis on the Relationship Between Colloidal Structure and Chemical Component of Asphalt Colloid and Performance

    OpenAIRE

    Cao, X J; Y. J. Ding

    2015-01-01

    Asphalt is considered a colloidal material and it is important to study the relationship between its colloidal structure, chemical components and performance. The aromatic nucleus content of asphalt at different depth analysed by attenuated total reflection (ATR) was taken as the index of colloid structure. The gray correlation was used to analyse the relationship between colloidal structure and chemical components of asphalt gel and performance. The results show that the correlation degree b...

  19. Asphalt Mixture for the First Asphalt Concrete Directly Fastened Track in Korea

    OpenAIRE

    Seong-Hyeok Lee; Dae-Wook Park; Hai Viet Vo; Samer Dessouky

    2015-01-01

    The research has been initiated to develop the asphalt mixtures which are suitable for the surface of asphalt concrete directly fastened track (ADFT) system and evaluate the performance of the asphalt mixture. Three aggregate gradations which are upper (finer), medium, and below (coarser). The nominal maximum aggregate size of asphalt mixture was 10 mm. Asphalt mixture design was conducted at 3 percent air voids using Marshall mix design method. To make impermeable asphalt mixture surface, th...

  20. Characterization of crumbe rubber and modified asphalt from brazilian petroleum; Caracterizacao de borracha de pneu moido e de asfalto modificado oriundo de petroleo brasileiro

    Energy Technology Data Exchange (ETDEWEB)

    Santos, Expedito F. dos; Feitosa, Judith P.A. [Ceara Univ., Fortaleza, CE (Brazil). Dept. de Quimica Organica e Inorganica]. E-mail: judith@dqoi.ufc.br, expeditoflavio@uol.com.br; Soares, Jorge B. [Ceara Univ., Fortaleza, CE (Brazil). Dept. de Engenharia de Transporte; Leite, Leni F.M. [PETROBRAS S.A., Rio de Janeiro, RJ (Brazil). Centro de Pesquisas

    2003-07-01

    Initially it was made an evaluation of the thermal behavior, grain composition and elastomer content of a crumb rubber sample. It was verified a thermal resistance of the crumb rubber and an elastomer content ranging from 56 to 68 %. The asphalt binders were obtained from Brazilian CAP (Fazenda Alegre, State of Espirito Santo) and blended with crumb rubber from 2 to 22 %. The asphalt binder presented smaller penetration than pure CAP. The pure asphalt and binder was aged by the RTFOT system. It was observed a C=O band due oxidation. In the asphalt binder with 2 and 5 % of crumb rubber was verified a smaller effect of the oxygen than in the pure asphalt, which suggests larger aging resistance. Apparent viscosity analysis showed that the pure asphalt has a Newtonian behavior in temperature higher than 150 deg C, while a pseudoplastic behavior of the asphalt binder increases with crumb rubber concentration. (author)

  1. Effects of circulating fluidized bed combustion (CFBC) fly ashes as filler on the performances of asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Qin Li; Hui Xu; Xiaoru Fu; Chen Chen; Jianping Zhai [Nanjing University, Nanjing (China). State Key Laboratory of Pollution Control and Resource Reuse

    2009-03-15

    This work investigated the potential of utilizing circulating fluidized bed combustion (CFBC) fly ashes (CFAs) as alternative filler, substituting mineral powders (MPs) that are widely used in asphalt concrete. Physico-chemical characteristics of the CFAs and MPs, as well as effects of different mix designs of CFAs and asphalt on asphalt performances were examined, including moisture susceptibility, viscosity, ductility, softening point, penetration, and antiaging performances. The results of the study show that generally the CFAs have greater effects than the MPs on improving the performances of asphalt, and that the specific surface area (SSA), free CaO (f-CaO), morphology, and mineralogical phases of the CFAs are more favorable than those of the MPs respectively, while the alkaline values, hydrophilic coefficients, particle size distributions (PSDs), and water contents of the two fillers are similar. It is suggested that CFAs may be more suitable than MPs for the use as asphalt concrete filler.

  2. 泡沫沥青用量对冷再生混合料疲劳性能的影响%The Effect of Foamed Asphalt Content on the Fatigue Performance of Cold Recycled Mixtures

    Institute of Scientific and Technical Information of China (English)

    周兵

    2014-01-01

    The-fatigue-property-of-foamed-asphalt-recycled-mixture-is-an-important-factor-that-affects-its-performance.Through-the-dosage-control-of-the-foamed-asphalt,the-indirect-tensile-strength-test-and-fatigue-test-are-performed,then-the-experimental-results-are-analyzed-to-find-the-relationship-be-tween-the-dosage-of-the-foamed-asphalt-and-the-performance-of-the-foamed-asphalt-mixture-in-order-to-get-a-better-understanding-of-the-performance-of-the-foamed-asphalt-mixture.%泡沫沥青再生混合料的疲劳性能是影响泡沫沥青混合料性能的重要因素。通过控制泡沫沥青的用量,采用间接拉伸强度试验和疲劳性能试验,并对实验结果进行分析,找出泡沫沥青用量和泡沫沥青混合料性能的关系。以期增加对泡沫沥青混合料疲劳性能的了解。

  3. Application of asphalt rubber technology to recreational trails

    Science.gov (United States)

    Ni, Haifeng

    Crumb rubber aggregate was employed instead of stone/sand aggregate in asphalt pavement that was modified by fine rubber particles. Crumb rubber aggregate forms an elastic network in the asphalt, which improves the pavement's susceptibility to low-temperature cracking, and absorb more stress at the crack tips than the conventional asphalt pavement. Laboratory tests were conducted to evaluate the tension/compression performance of a blend of asphalt rubber with rubber aggregate (ARRA). An optimum design methodology was introduced by examining the effect of asphalt source, curing temperature, curing time, rubber content, aggregate size, compaction pressure, and the effect of certain additives. At ambient temperature, the ARRA with equal amount of binder and aggregate exhibits good mechanical properties. Vestenamer helps improve the pavement's strength, stiffness, and fracture resistance to low temperature cracking. It was demonstrated that such pavement meets the mechanical requirements for recreational trails, such as bicycle, or pedestrian trails. ARRA is a viscoelastic material which exhibits time-dependent and loading rate-dependent behavior. Temperature is a key issue to its response to an external load. Both temperature and rate dependences were investigated. A series of uniaxial compression relaxation tests on ARRA or Vestenamer modified ARRA were conducted at room temperature to study the time-dependent performance of ARRA. Schapery's theory was applied to characterize the nonlinear viscoelastic behavior of ARRA.

  4. UTILIZATION OF WASTE PLASTIC BOTTLES IN ASPHALT MIXTURE

    Directory of Open Access Journals (Sweden)

    TAHER BAGHAEE MOGHADDAM

    2013-06-01

    Full Text Available Nowadays, large amounts of waste materials are being produced in the world. One of the waste materials is plastic bottle. Generating disposable plastic bottles is becoming a major problem in many countries. Using waste plastic as a secondary material in construction projects would be a solution to overcome the crisis of producing large amount of waste plastics in one hand and improving the structure’s characteristics such as resistance against cracking on the other hand. This study aimed to investigate the effects of adding plastic bottles in road pavement. Marshall properties as well as specific gravity of asphalt mixture containing different percentages of plastic bottles were evaluated. Besides, Optimum Asphalt Content (OAC was calculated for each percentages of plastic bottles used in the mix. The stiffness and fatigue characteristics of mixture were assessed at OAC value. Results showed that the stability and flow values of asphalt mixture increased by adding waste crushed plastic bottle into the asphalt mixture. Further, it was shown that the bulk specific gravity and stiffness of mixtures increased by adding lower amount of plastic bottles; however, adding higher amounts of plastic resulted in lower specific gravity and mix stiffness. In addition, it was concluded that the mixtures containing waste plastic bottles have lower OAC values compared to the conventional mixture, and this may reduce the amount of asphalt binder can be used in road construction projects. Besides, the mixtures containing waste plastic showed significantly greater fatigue resistance than the conventional mixture.

  5. Performance evaluation of high modulus asphalt concrete mixes

    Science.gov (United States)

    Haritonovs, V.; Tihonovs, J.; Zaumanis, M.

    2016-04-01

    Dolomite is one of the most available sedimentary rocks in the territory of Latvia. Dolomite quarries contain about 1000 million tons of this material. However, according to Latvian Road Specifications, this dolomite cannot be used for average and high intensity roads because of its low quality (mainly, LA index). Therefore, mostly imported magmatic rocks (granite, diabase, gabbro, basalt) or imported dolomite are used which makes asphalt expensive. However, practical experience shows that even with these high quality materials roads exhibit rutting, fatigue and thermal cracks. The aim of the research is to develop a high performance asphalt concrete for base and binder courses using only locally available aggregates. In order to achieve resistance against deformations at a high ambient temperature, a hard grade binder was used. Workability, fatigue and thermal cracking resistance, as well as sufficient water resistance is achieved by low porosity (3-5%) and higher binder content compared to traditional asphalt mixtures. The design of the asphalt includes a combination of empirical and performance based tests, which in laboratory circumstances allow simulating traffic and environmental loads. High performance AC 16 base asphalt concrete was created using local dolomite aggregate with polymer modified (PMB 10/40-65) and hard grade (B20/30) bitumen. The mixtures were specified based on fundamental properties in accordance to EN 13108-1 standard.

  6. The Study of Water Stability for SBS and Polyacrylate Composite Modified Asphalt Mixture

    Directory of Open Access Journals (Sweden)

    HU Qiusheng

    2014-09-01

    Full Text Available Polyacrylate (Polyacrylate, called PAE is a kind of thermoplastic polymer latex, which is easy to form a waterproof membrane and has greater adhesion ,always be used in concrete to enhance its ability to resist water corrosion.SBS is an inorganic modifier for modified asphalt mixture will help to improve the high and low temperature stability and other road performance, ect.However,its ability to enhanced asphalt mixture’s resistance for water damage is not obvious. In order to research the two composite modified asphalt mixture’s resistance effects to water damage , the Marshall Stability Test and Fort Kentucky Flooding Scattering Experiments were used on asphalt mixtures, SBS modified asphalt mixture and composite modified asphalt mixture and the effect of different composite modified PAE content were studied. The results showed that: PAE can significantly improve the water stability of asphalt mixture, what’s more, with the increase use of PAE,the mass loss rate of asphalt mixture decreases steadily.

  7. Investigation of modified asphalt concrete

    Science.gov (United States)

    Zimich, Vita

    2016-01-01

    Currently the problem of improving the asphalt quality is very urgent. It is used primarily as topcoats exposed to the greatest relative to the other layers of the road, dynamic load - impact and shear. The number of cars on the road, the speed of their movement, as well as the traffic intensity increase day by day. We have to upgrade motor roads, which entails a huge cost. World experience shows that the issue is urgent not only in Russia, but also in many countries in Europe, USA and Asia. Thus, the subject of research is the resistance of asphalt concrete to water and its influence on the strength of the material at different temperatures, and resistance of pavement to deformation. It is appropriate to search for new modifiers for asphaltic binder and mineral additives for asphalt mix to form in complex the skeleton of the future asphalt concrete, resistant to atmospheric condensation, soil characteristics of the road construction area, as well as the growing road transport load. The important task of the work is searching special modifying additives for bitumen binder and asphalt mixture as a whole, which will improve the quality of highways, increasing the period between repairs. The methods described in the normative-technical documentation were used for the research. The conducted research allowed reducing the frequency of road maintenance for 7 years, increasing it from 17 to 25 years.

  8. Airborne exposures to PAH and PM2.5 particles for road paving workers applying conventional asphalt and crumb rubber modified asphalt.

    Science.gov (United States)

    Watts, R R; Wallingford, K M; Williams, R W; House, D E; Lewtas, J

    1998-01-01

    Personal exposure monitoring was conducted for road paving workers in three states. A research objective was to characterize and compare occupational exposures to fine respirable particles (asphalt and asphalt containing crumb rubber from shredded tires. Workers not exposed to asphalt fume were also included for comparison (to support the biomarker component of this study). The rubber content of the crumb rubber modified (CRM) asphalt at the three study sites was 12, 15, and 20%. A comparison of some specific job categories from two sites indicates greater potential carcinogenic PAH exposures during CRM asphalt work, however, the site with the greatest overall exposures did not indicate any differences for specific jobs. A statistical analysis of means for fine particle, pyrene and total carcinogenic PAH personal exposure shows, with two exceptions, there were no differences in exposures for these three measurement variables. One site shows significantly elevated pyrene exposure for CRM asphalt workers and another site similarly shows greater carcinogenic PAH exposure for CRM asphalt workers. Conventional and CRM asphalt worker airborne exposures to the PAH carcinogen marker, BaP, were very low with concentrations comparable to ambient air in many cities. However, this study demonstrates that asphalt road paving workers are exposed to elevated airborne concentrations of a group of unknown compounds that likely consist of the carcinogenic PAHs benz(a)anthracene, chrysene and methylated derivatives of both. The research described in this article has been reviewed in accordance with U.S. Environmental Protection Agency policy and approved for publication. Mention of trade names or commercial products does not constitute endorsement or recommendation for use. PMID:9577752

  9. Nanomaterials Applied in Asphalt Modification: A Review

    Institute of Scientific and Technical Information of China (English)

    Changqing Fang; Ruien Yu; Shaolong Liu; Yan Li

    2013-01-01

    Nanotechnology has been gradually penetrated into the field of asphalt modification.Seemingly magic effects of nanomaterials have now been brought to improve the performance of asphalt.To demonstrate many of the prospective applications,researchers have conducted a series of positive and effective efforts dealing with the preparation of modified asphalt to demonstrate the mechanism of modification and the resultant improvement in performance.In this review,various nanomaterials used in asphalt modification are initially presented,followed by the methods employed to modify the asphalt with these materials and finally the effects of nanomaterials on the performance of base asphalt are presented and the modification mechanisms are discussed.Based on the current research results,the influence of preparation process parameters on the compatibility of every phase in the modified asphalt and the stability of the modified asphalt system are described.Finally,the development trend of the topic field is projected.

  10. Laboratory aging of asphalt mixtures : simulation of reclaimed asphalt and application as test method for durability

    OpenAIRE

    Mollenhauer, Konrad; MOUILLET, Virginie; PIERARD, Nathalie; TUSAR, Marjan; Gabet, Thomas

    2012-01-01

    Surface asphalt courses reach their end of service life after a time span between 10 and 30 years, depending on their durability. Afterwards, the surface layer is usually milled and reused in asphalt mixtures as reclaimed asphalt. In order to enable the analysis of durability and recyclability of a new asphalt mixture, four laboratory aging procedures were designed and comparatively applied on twoasphalt mixes. Besides aging of loose asphalt mix in heating cabinets at varied temperatures and ...

  11. Sinopec Launches Shanghai Asphalt Sales Company

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ Sinopec Shanghai Asphalt Sales Company was launched in Shanghai on September 22, marking Sinopec as the largest asphalt supplier in China integrated in famous brand,production, sales and research, and distribution network.This is another important initiative for Sinopec's asphalt segment, after Sinopec won the bid for construction of F 1 racing course, to grasp the market opportunities, further improve the product quality and the level of after-sales services, and further make its asphalt business larger and stronger.

  12. Laboratory optimization of continuous blend asphalt rubber

    OpenAIRE

    Fontes, Liseane P. T. L.; Pereira, Paulo A. A.; Trichês, Glicério; Pais, Jorge C.; Luzia, Rosa

    2008-01-01

    Asphalt rubber from wet process requires batching blending and reaction time associated to blending rubber and conventional asphalt to produce asphalt rubber. The ideal blending of these materials depends on the combination of very important variables, such as the amount of rubber, reaction time and temperature reaction. This paper intends to optimize the laboratory production of asphalt rubber using the continuous blend process. The rubber from waste tyres was reduced by ambient grinding and...

  13. Evaluating permanent deformation in asphalt rubber mixtures

    OpenAIRE

    Fontes, Liseane P. T. L.; Trichês, Glicério; Pais, Jorge C.; Pereira, Paulo A. A.

    2009-01-01

    Permanent deformation or rutting, one of the most important distresses inflexible pavements, has long been a problem in asphalt mixtures. Throughout the years, researchers have used different test methods lo estimate the performance of asphalt mixtures in relation to rutting. One of the alternatives to reduce permanent deformation in asphalt pavement layers is through the use of mixtures produced with asphalt rubber This work aims at comparing the performance of a conventional dense graded mi...

  14. Asphalt Carriers from Kraljevica Shipyard, Croatia

    OpenAIRE

    Grubišić, R.

    2006-01-01

    This article is based on the materials presented by the experts from Kraljevica Shipyard at the annual meeting of the Croatian shipbuilding designers held in Kraljevica in October 2005. Asphalt tanker Asphalt Seminole and her sister-ships are rather sophisticated vessels having a complex hull structure, cargo space and cargo survey and control equipment. Therefore, firstly the technical data of the already delivered asphalt tanker Asphalt Seminole are given and then, the very interesting d...

  15. Reducing Your Cost for Asphalt Pavements

    OpenAIRE

    Evans, Alvin

    2012-01-01

    This session will discuss of how local government decision-makers can achieve greater value without sacrificing quality or service life. The session will touch upon use of Higher Recycled Asphalt Pavement (RAP), Recycled Asphalt Shingles (RAS), Asphalt Mix Design for Heavy Traffic vs. Light Traffic, Speed of Construction, Perpetual Pavement and Pavement Rehabilitation Strategies.

  16. Initiative assessment of asphalt works

    International Nuclear Information System (INIS)

    Several asphalt works are utilizing heat from combustion of used oil for drying and heating of rock material in the production of asphalt. According to new regulations on combustion of waste, used oil is to be regarded as waste and subject to emission requirements according to the combustion regulations. Measurements show that emissions of CO, dust, dioxins, TOC and SO2 exceed the limits set by the regulations. To conform to the regulations these asphalt works must improve their combustion technique. However, such measures may lead to increased formation of NOx. It is recommended that a combustion chamber for drying of rock material should be used in order to reduce the emissions of CO and TOC concentrations. The concentration of SO2 may be reduced by dry cleaning by means of injection of lime. In the same way, active carbon is injected to remove dioxins. The asphalt works must be outfitted with measuring equipment that monitors and records certain operation and control parameters and some emission to air parameters. Periodic measurements are to be done of heavy metals and dioxins. It is estimated that the measures necessary to make the asphalt works comply with the regulations will cost about NOK 4 530 000 in investment per plant and that the operation expenses will increase by NOK 700 000 per year per plant. This includes maintenance, control etc

  17. The improvement of pavement performance using asphalt rubber hot mixes

    OpenAIRE

    Pais, Jorge C.; Pereira, Paulo A. A.

    2007-01-01

    The need of a better pavement performance has led researchers to develop new road materials, mainly for the asphalt layers, where the modification of the asphalt is the main example. This modification usually forces the use of polymers and fibers and, more recently, the use of crumb rubber from ground tires, where the modified asphalt is known as asphalt rubber. This asphalt rubber used in asphalt mixtures produces a superior performance if compared to the asphalt mixtures with...

  18. Influence of Subgrade and Unbound Granular Layers Stiffness on Fatigue Life of Hot Mix Asphalts - HMA

    OpenAIRE

    Hugo A. Rondón-Quintana; Wilmar D. Fernández-Gómez; Jesús A. Hernández-Noguera

    2013-01-01

    The mainly factors studied to predict fatigue life of hot mix asphalt-HMA in flexible pavements are the loading effect, type of test, compaction methods, design parameters of HMA (e.g., particle size and size distribution curve, fine content, type of bitumen) and the variables associated with the environment (mainly moisture, temperature, aging). This study evaluated through a computer simulation, the influence of the granular layers and subgrade on the fatigue life of asphalt layers in flexi...

  19. Modeling of asphalt-rubber rotational viscosity by statistical analysis and neural networks

    OpenAIRE

    Luciano Pivoto Specht; Oleg Khatchatourian; Lélio Antônio Teixeira Brito; Jorge Augusto Pereira Ceratti

    2007-01-01

    It is of a great importance to know binders' viscosity in order to perform handling, mixing, application processes and asphalt mixes compaction in highway surfacing. This paper presents the results of viscosity measurement in asphalt-rubber binders prepared in laboratory. The binders were prepared varying the rubber content, rubber particle size, duration and temperature of mixture, all following a statistical design plan. The statistical analysis and artificial neural networks were used to c...

  20. A Study on the Rheological Properties of Recycled Rubber-Modified Asphalt Mixtures

    OpenAIRE

    Murat Karacasu; Volkan Okur; Arzu Er

    2015-01-01

    Using waste rubber in asphalt mixes has become a common practice in road construction. This paper presents the results of a study on the rheological characteristics of rubber-modified asphalt (RMA) concrete under static and dynamic loading conditions. A number of static and dynamic creep tests were conducted on RMA mix specimens with different rubber sizes and contents, and a series of resonant column tests were conducted to evaluate the shear modulus and damping values. To simulate the stres...

  1. Assessment of the performance of asphalt rubber layers on noise abatement

    OpenAIRE

    Freitas, Elisabete; Pereira, Paulo; Anfosso Ledee, Fabienne

    2008-01-01

    Layers with a very high content of rubber have shown to be very effective on noise abatement despite their reduced durability. On the contrary, layers with a rubberized asphalt binder have shown to be durable, but their performance regarding noise abatement is not consensual yet. This paper aims at assessing the effect of the use of layers with rubberized asphalt binder on noise abatement. For this purpose seven road sections with different surface types, among which five gap graded and three...

  2. Assessment of the performance of asphalt rubber layers on noise abatement

    OpenAIRE

    Freitas, Elisabete F.; Pereira, Paulo A. A.; Anfosso-Lédée, Fabienne

    2008-01-01

    Layers with a very high content of rubber have shown to be very effective on noise abatement despite their reduced durability. On the contrary, layers with a rubberized asphalt binder have shown to be durable, but their performance regarding noise abatement is not consensual yet. This paper aims at assessing the effect of the use of layers with rubberized asphalt binder on noise abatement. For this purpose seven road sections with different surface types, among which five gap grad...

  3. Waterproofing improvement of radioactive waste asphalt solid

    International Nuclear Information System (INIS)

    Purpose: To improve the waterproofing of asphalt solid by adding an alkaline earth metal salt and, further, paraffin, into radioactive liquid waste when processing asphalt solidification of the radioactive liquid waste. Method: Before processing molten asphalt solidification of radioactive liquid waste, soluble salts of alkaline earth metal such as calcium chloride, magnesium chloride, or the like is added to the radioactive liquid waste. Paraffin having a melting point of higher than 600C, for example, is added to the asphalt, and waterproofing can be remarkably improved. The waste asphalt solid thus fabricated can prevent the swelling thereof, and can improve its waterproofing. (Yoshihara, H.)

  4. Asphalt Mixture for the First Asphalt Concrete Directly Fastened Track in Korea

    Directory of Open Access Journals (Sweden)

    Seong-Hyeok Lee

    2015-01-01

    Full Text Available The research has been initiated to develop the asphalt mixtures which are suitable for the surface of asphalt concrete directly fastened track (ADFT system and evaluate the performance of the asphalt mixture. Three aggregate gradations which are upper (finer, medium, and below (coarser. The nominal maximum aggregate size of asphalt mixture was 10 mm. Asphalt mixture design was conducted at 3 percent air voids using Marshall mix design method. To make impermeable asphalt mixture surface, the laboratory permeability test was conducted for asphalt mixtures of three different aggregate gradations using asphalt mixture permeability tester. Moisture susceptibility test was conducted based on AASHTO T 283. The stripping percentage of asphalt mixtures was measured using a digital camera and analyzed based on image analysis techniques. Based on the limited research results, the finer aggregate gradation is the most suitable for asphalt mixture for ADFT system with the high TSR value and the low stripping percentage and permeable coefficient. Flow number and beam fatigue tests for finer aggregate asphalt mixture were conducted to characterize the performance of asphalt mixtures containing two modified asphalt binders: STE-10 which is styrene-butadiene-styrene (SBS polymer and ARMA which is Crum rubber modified asphalt. The performance tests indicate that the STE-10 shows the higher rutting life and fatigue life.

  5. A model for predicting thermal properties of asphalt mixtures from their constituents

    Science.gov (United States)

    Keller, Merlin; Roche, Alexis; Lavielle, Marc

    Numerous theoretical and experimental approaches have been developed to predict the effective thermal conductivity of composite materials such as polymers, foams, epoxies, soils and concrete. None of such models have been applied to asphalt concrete. This study attempts to develop a model to predict the thermal conductivity of asphalt concrete from its constituents that will contribute to the asphalt industry by reducing costs and saving time on laboratory testing. The necessity to do the laboratory testing would be no longer required when a mix for the pavement is created with desired thermal properties at the design stage by selecting correct constituents. This thesis investigated six existing predictive models for applicability to asphalt mixtures, and four standard mathematical techniques were used to develop a regression model to predict the effective thermal conductivity. The effective thermal conductivities of 81 asphalt specimens were used as the response variables, and the thermal conductivities and volume fractions of their constituents were used as the predictors. The conducted statistical analyses showed that the measured values of thermal conductivities of the mixtures are affected by the bitumen and aggregate content, but not by the air content. Contrarily, the predicted data for some investigated models are highly sensitive to air voids, but not to bitumen and/or aggregate content. Additionally, the comparison of the experimental with analytical data showed that none of the existing models gave satisfactory results; on the other hand, two regression models (Exponential 1* and Linear 3*) are promising for asphalt concrete.

  6. Evaluation on Low Temperature Performance of Recycled Asphalt Mixture Using Warm Mix Asphalt Technology

    Directory of Open Access Journals (Sweden)

    Xiaolan Duan,

    2015-04-01

    Full Text Available In this paper, the basic idea is about the recycled technology of asphalt mixture, more in-depth study of the lowtemperature performance of warm mix asphalt(WMA.First of all, Including the evaluation of low temperature performance of WMA made of reclaimed asphalt pavement (RAP (passed and not passed 2.36mm screen, and the influence of WMA with RAP mixed of different dosage of dispersant. Then, using the SBS modified asphalt and base asphalt were test at low temperature, research on the influence of different type of asphalt to the low temperature performance of WMA.

  7. Effect of Components on the Performance of Asphalt Modiifed by Waste Packaging Polyethylene

    Institute of Scientific and Technical Information of China (English)

    ZHANG Maorong; FANG Changqing; ZHOU Shisheng; CHENG Youliang; YU Ruien; LIU Shaolong; LIU Xiaolong; SU Jian

    2016-01-01

    Waste packaging polyethylene (WPE) was used to modify raw asphalt by melt blending the components at 190℃ for 1 h in a simple mixer and subsequently machining them at 120℃ for 1 h in a high-speed shearing machine. The effect of modiifcation on the degree of the penetration, the softening point and the ductility of the asphalt was studied using lfuorescent microscopy, infrared spectrometry, component changes and various other techniques. The experimental results showed that no chemical reactions took place in the components themselves (saturate, aromatic, asphaltene and resin) during the modifications. The softening point and penetration of the asphalt were found to be closely related to the resulting contents of the asphaltene, saturate and resin components. In addition, aromatics were identified as having the greatest impact on the ductility of the asphalt.

  8. Rheological characteristics of aged asphalt binder

    Institute of Scientific and Technical Information of China (English)

    刘聪慧; 吴少鹏; 刘全涛; 朱国军

    2008-01-01

    Different aging levels(RTFOT,PAV-10h,PAV-20h and PAV-30 h) of asphalt binders with various mass ratios of mineral powder to asphalt(0,0.4,0.8,1.2,1.6,2.0) were used to investigate the rheological properties of aged asphalt binders with respect to their short and long terms aging characteristics.Viscosity test,dynamic shear test and creep test were conducted.The test results indicate that the viscosity of aged asphalt binder increases sharply with the extension of aging period.Complex shear modulus of aged asphalt increases,which indicates that the stiffness of asphalt binders can increase.The phase angle for aged asphalt binders reduces,which indicates that the elastic portion for viscoelastic property of asphalt binders increases.|G*|·sin δ increases after aging procedure which means that the fatigue resistance becomes poor.The creep test results show that creep strain curves varies remarkably for virgin and aged asphalt binders.The total strain during loading period and the permanent strain decreases significantly for aged asphalt binders,which implies that the elastic portion increases and the viscous portion decreases.

  9. Modelling and Laboratory Studies on the Adhesion Fatigue Performance for Thin-Film Asphalt and Aggregate System

    Directory of Open Access Journals (Sweden)

    Dongsheng Wang

    2014-01-01

    Full Text Available Adhesion between asphalt and aggregate plays an important role in the performance of asphalt mixtures. A low-frequency adhesion fatigue test was proposed in this paper to study the effect of environment on the asphalt-aggregate adhesion system. The stress-based fatigue model had been utilized to describe the fatigue behavior of thin-film asphalt and aggregate system. The factors influencing the adhesion fatigue performance were also investigated. Experiment results show that asphalt has more important effect on the adhesion performance comparing with aggregate. Basalt, which is regarded as hydrophobic aggregates with low silica content, has better adhesion performance to asphalt binder when compared with granite. The effects of aging on the adhesion fatigue performance are different for PG64-22 and rubber asphalt. Long-term aging is found to reduce the adhesion fatigue lives for rubber asphalt and aggregate system, while the effect of long-term aging for aggregate and PG64-22 binder system is positive. Generally the increased stress amplitude and test temperature could induce greater damage and lead to less fatigue lives for adhesion test system.

  10. Modelling and laboratory studies on the adhesion fatigue performance for thin-film asphalt and aggregate system.

    Science.gov (United States)

    Wang, Dongsheng; Yi, Junyan; Feng, Decheng

    2014-01-01

    Adhesion between asphalt and aggregate plays an important role in the performance of asphalt mixtures. A low-frequency adhesion fatigue test was proposed in this paper to study the effect of environment on the asphalt-aggregate adhesion system. The stress-based fatigue model had been utilized to describe the fatigue behavior of thin-film asphalt and aggregate system. The factors influencing the adhesion fatigue performance were also investigated. Experiment results show that asphalt has more important effect on the adhesion performance comparing with aggregate. Basalt, which is regarded as hydrophobic aggregates with low silica content, has better adhesion performance to asphalt binder when compared with granite. The effects of aging on the adhesion fatigue performance are different for PG64-22 and rubber asphalt. Long-term aging is found to reduce the adhesion fatigue lives for rubber asphalt and aggregate system, while the effect of long-term aging for aggregate and PG64-22 binder system is positive. Generally the increased stress amplitude and test temperature could induce greater damage and lead to less fatigue lives for adhesion test system. PMID:25054187

  11. Effects of Mineral Filler to Polymer Modified Bitumen Ratio on the Design Properties of Hot Mix Asphalt and its Performance

    Directory of Open Access Journals (Sweden)

    Imran Hafeez

    2010-10-01

    Full Text Available Current development in the design of asphalt concrete especially in the upper layers of flexible pavements contains about acceptable proportion of mineral fillers passing 75?m (# 200 sieve, which contributes towards the mix cohesion, resistant to rutting and improves serviceability. Three filler to PMA (Polymer Modified Asphalt ratios (i.e. 2.4, 3.4. and 4.4% in Marshall Method of mix design were used in order to determine the optimum filler content at relatively low design asphalt contents (3.83%, for asphalt concrete having PMA and 100% lime stone dust. Designed mix was laid on Southbound Turnol Taxila National Highway Section (N-5, Pakistan as a trial in year 2003. The study reveals that filler to asphalt ratio affects the mix properties to a greater extent and mix laid at site have shown relatively better performance during its service life of initial four critical years. For coarse graded mixes with low asphalt contents, designed especially for heavy loading and high temperatures regions like Pakistan, filler to asphalt ratio less than equal to 1.0 yields better results.

  12. Evaluation of Marshall Properties of Warm Mix Asphalt using Sasobit

    OpenAIRE

    Renugadevi. A

    2014-01-01

    With increasing concerns of global warming and increasing exhaustion of greenhouse gases, the asphalt industry is looking for alternatives for hot mix asphalt (HMA).Warm Mix Asphalt (WMA) is a fast emerging new technology which has a potential of revolutionizing the production of asphalt mixtures. WMA technology allows the mixing, lay down and compaction of asphalt mixes at significantly lower temperatures compared to Hot Mix Asphalt (HMA). The technology can reduce production tem...

  13. Operational properties of nanomodified stone mastic asphalt

    OpenAIRE

    Inozemtsev Sergey Sergeevich; Korolev Evgeniy Valer’evich

    2015-01-01

    In order to prolong the lifetime and to improve the quality of pavements made of asphalt concrete it is necessary to apply innovative solutions in the process of design of such building materials. In order to solve the problem of low durability of asphalt concrete a modifier was proposed, which consists of diatomite, iron hydroxide sol (III) and silica sol. Application of the diatomite with nanoscale layer of nanomodifier allows getting a stone mastic asphalt, which has high values of physica...

  14. Microstructural characterisation of rubber modified asphalt mixtures

    OpenAIRE

    Abdul Hassan, Norhidayah

    2013-01-01

    Research to improve the performance of asphalt mixtures through the addition of crumb rubber using the dry process has continued worldwide because of its potential as a recycling option for used tires. For decades, dry mixed rubberised asphalt mixtures have performed inconsistently in field trials and laboratory evaluations. However, current research has revealed that the performance of asphalt mixtures is highly dependent on the characteristics of its internal structure or phase constituents...

  15. Construction and maintenace of porous asphalt

    OpenAIRE

    Kert, Gregor

    2012-01-01

    In improving traffic safety and reducing traffic noise road building experts from Slovenia and the world are faced with permeable surfaces - namely porous asphalt. There is hardly any water retention on road surfaces with the use of porous asphalt, what Slovenian engineers efficiently use on motorways where transverse profile changes its direction. Lately, porous asphalt is also being used for traffic noise reduction. However, porous road surface has some important disadvantages due to its...

  16. The use of asphalt in hydraulic engineering

    OpenAIRE

    Van de Velde, P.A.; Ebbens, E.H.; Van Herpen, J.A.

    1985-01-01

    Asphalt products have been used in the Netherlands in hydraulic engineering for a long time on a large scale, especially after the great disaster in 1953 when a large part of western Holland was flooded by the sea. After the disaster a great number of dikes had to be repaired very quickly and this was possible with the use of asphalt as a revetment material. Asphalt could be placed much faster then the materials most commonly used in those days. Further more asphalt is, when desired, more wat...

  17. Asphalt solar collectors: A literature review

    International Nuclear Information System (INIS)

    Highlights: ► Solar energy can be harnessed by asphalt pavements. ► Research on asphalt thermal behavior and asphalt solar collectors is reviewed. ► Asphalt temperature is very sensitive to the variation of absortivity. ► Asphalt solar collector efficiency depends on flow rate and geometrical parameters. -- Abstract: Asphalt pavements subject to solar radiation can reach high temperatures causing not only environmental problems such as the heat island effect on cities but also structural damage due to rutting or hardening as a result of thermal cycles. Asphalt solar collectors are doubly effective active systems: as they solve the previously mentioned problems and, moreover, they can harness energy to be used in different applications. The main findings of the existing research on asphalt solar collectors are gathered together in this review paper. Firstly, the main heat transfer mechanisms involved in the solar energy collection process are identified and the most important parameters and variables are presented. After analyzing the theoretical foundations of the heat transfer process, this review focuses on the types of studies carried out so far on asphalt’s thermal behavior, different methodologies employed by other authors to study asphalt solar collectors and influence of the variables involved in thermal energy harvesting.

  18. Investigation of Low Heat Accumulation Asphalt Mixture and Its Impact on Urban Heat Environment.

    Directory of Open Access Journals (Sweden)

    Jianguang Xie

    Full Text Available This study is focused on investigating the effectiveness of low heat accumulation asphalt mixture and its impact on the urban heat environment. Infrared radiation experiments showed that the temperature of the asphalt mixture decreased with the increase in far-infrared radiant material. The results also revealed that, compared to asphalt with 0% far-infrared radiant content, the asphalt material with a certain ratio of far-infrared radiation material had higher stability at high and low temperatures as well as good water absorption capacity. The Marshall stability of the specimen mixed with 6% far-infrared radiant was higher by 12.2% and had a residual stability of up to 98.9%. Moreover, the low-temperature splitting tensile strength of the asphalt mixture with 6% far-infrared radiation material increased by 21.3%. The friction coefficient of the asphalt mixtures with 6% and 12% far-infrared radiation material increased by 17.7% and 26.9%, respectively.

  19. Physical and environmental properties of asphalt mixtures containing incinerator bottom ash.

    Science.gov (United States)

    Huang, Chin-Ming; Chiu, Chui-Te; Li, Kung-Cheh; Yang, Wan-Fa

    2006-10-11

    This paper presents parts of the results from a research project sponsored by Taiwan Environmental Protection Administration (TEPA), investigating both the physical and environmental properties of asphalt mixtures using different amount of incinerator bottom ash (IBA) as fine aggregate substitution. The Marshall mix design method was used to determine the design asphalt content and evaluate the potential performance of these IBA-asphalt mixtures. Water sensitivity and wheel track rutting were also performed on these mixtures. Leachates, from both laboratory and outdoor leaching tests, were performed to measure the concentration of selected heavy metals and the level of daphnia toxicity. While with adequate Marshall stability, the IBA-asphalt mixtures were shown to have excessively high Marshall flow and excessively low VMA (voids in the mineral aggregate). The results of the wheel tracking tests also indicated that the IBA-asphalt mixtures had low rutting resistance. The results of the water sensitivity test according to procedure of AASHTO T283 method showed that the IBA-asphalt mixtures had a higher tensile strength ratio (TSR) as compared with the conventional asphalt mixtures. Considering the environmental aspects, outdoor leaching tests showed that IBA had a high level of daphnia toxicity. From an ecological perspective, IBA could be identified as hazardous waste in Taiwan. However, after being mixed with asphalt binder, the concentration of heavy metals and the levels of daphnia toxicity were significantly reduced. The leachates of 10-day flat plate leaching tests on Marshall specimens containing IBA indicated that the heavy metal were undetectable and the daphnia toxicity was ineffective. PMID:16787702

  20. Resonance Testing of Asphalt Concrete

    OpenAIRE

    Gudmarsson, Anders

    2014-01-01

    This thesis present novel non-destructive laboratory test methods to characterize asphalt concrete. The testing is based on frequency response measurements of specimens where resonance frequencies play a key role to derive material properties such as the complex modulus and complex Poisson’s ratio. These material properties are directly related to pavement quality and used in thickness design of pavements. Since conventional cyclic loading is expensive, time consuming and complicated to perfo...

  1. Rheological characterization of aged asphalts

    International Nuclear Information System (INIS)

    The present work shows the rheological properties of the three Colombian asphalts produced in the refineries at Barrancabermeja, Cartagena and Apiay, exposed to the open air during 18 months using a specially designed testing bank. rheological behavior was evaluated using the new specifications of SHRP technology in the Brookfield and DSR rheometers to determine viscosity, shear stress, shear rate, dynamic share modulus and other related variables. The measurements were made using different temperatures and load times

  2. Impact of defective production of asphalt mixture resulting in damaged asphalt layers

    OpenAIRE

    Hrovat, Tea

    2013-01-01

    In practice it often happens that a newly built road soon, after the asphalt mixture is added, starts showing first cracks and damages, which are not necessarily always a fault of the contractor, who built in the asphalt mixture, but can derive from the production of asphalt mixture. Such mistakes in the production of the asphalt mixture are hard to prove, since all the contractors usually put the blame on the automatic mixing production in the asphalt plant. During the production of the asph...

  3. Analysing polystyrene-modified asphalt and its incidence in a heat-dense asphalt mixture

    OpenAIRE

    Ana Sofía Figueroa Infante; Fredy Alberto Reyes Lizcano; Diana Hernández Barrera; Christian Jiménez; Natalia Bohórquez

    2010-01-01

    This article presents some results obtained with an MDC-2 asphalt/polystyrene-modified asphalt mixture as a result of crushing waste glass. The stone, asphalt and polystyrene materials’ were characterised for drawing up the design. The Marshal method was used for obtaining the best asphalt- stone-polystyrene percentages. The Superpave method was used for analysing the asphalt; the mixture’s dynamic behaviour was analysed using a test involving 20ºC and 30ºC trapezoidal fatigue for 90x10-6, 15...

  4. Evaluation on Low Temperature Performance of Recycled Asphalt Mixture Using Warm Mix Asphalt Technology

    OpenAIRE

    Xiaolan Duan,; Chunge Li

    2015-01-01

    In this paper, the basic idea is about the recycled technology of asphalt mixture, more in-depth study of the lowtemperature performance of warm mix asphalt(WMA).First of all, Including the evaluation of low temperature performance of WMA made of reclaimed asphalt pavement (RAP) (passed and not passed 2.36mm screen), and the influence of WMA with RAP mixed of different dosage of dispersant. Then, using the SBS modified asphalt and base asphalt were test at low temperature, researc...

  5. Use of steel slag aggregate in asphalt concrete mixes

    Energy Technology Data Exchange (ETDEWEB)

    Asi, I.M.; Qasrawi, Y.; Shalabi, F.I. [Hashemite Univ., Zarqa (Jordan). Dept. of Civil Engineering

    2007-08-15

    The physical, chemical and mechanical properties of generated steel slag aggregates (SSA) were studied in order to investigate their potential use in asphalt concrete (AC) mixes. Five AC mixes were investigated, notably an AC mix with a 100 per cent limestone aggregate, and mixes comprised of 25, 50, 75, and 100 per cent SSA coarse aggregates. A superpave mix design was used to determine optimum asphalt content (OAC). Steps included the selection of a design aggregate structure, optimization of the asphalt content for the structure, and an evaluation of the moisture sensitivity of the design mixture. The effectiveness of the samples were assessed by their ability to improve indirect tensile strength (ITS); resilient and creep modulus; fatigue life; and stripping and rutting resistance. Various AC mixes containing the SSA were then evaluated. A gyratory compactor was used to compact the test samples, which were then subjected to comprehensive mechanical evaluations. Statistical analyses were then performed to examine the significance of the SSA percentage in the changing ITS values using analysis of variance (ANOVA) calculations. Results of the study indicated that SSA met both superpave consensus properties and Jordanian standards source properties. Chemical and toxic levels were within allowable limits. It was concluded that optimal the replacement percentage of SSA was 25 per cent. 18 refs., 9 tabs., 21 figs.

  6. Asphalt solidification of mixed wastes

    International Nuclear Information System (INIS)

    Mixed wastes pose a problem to generators since there are no burial sites or treatment facilities currently accepting this waste type. One potential disposal method is treating the waste to render it non-hazardous, and disposing of it in accordance with radioactive waste requirements. A possible means of accomplishing this transformation is solidifying the waste in asphalt (bitumen). Associated Technologies Incorporated, in cooperation with Oak Ridge National Laboratory, solidified in asphalt a surrogate sodium nitrate-based waste, spiked with EPtoxic metals and non-radioactive cesium and strontium. This paper reports the characteristics of the spiked ORNL solution that was solidified as well as the properties of the solidified end product. The waste samples generated underwent EP toxicity testing as well as ANS 16.1 leach testing for 90 days and the results of those tests are presented. Also, a discussion of the criteria for classifying a waste as hazardous are included in order to demonstrate that the waste, once solidified in asphalt, may no longer be considered hazardous

  7. Sustainable asphalt pavement: Application of slaughterhouse waste oil and fly ash in asphalt binder

    Science.gov (United States)

    Sanchez Ramos, Jorge Luis

    Increasing energy costs, lack of sufficient natural resources and the overwhelming demand for petroleum has stimulated the development of alternative binders to modify or replace petroleum-based asphalt binders. In the United States, the petroleum-based asphalt binder is mainly used to produce the Hot Mix Asphalt (HMA). There are approximately 4000 asphalt plants that make 500 million tons of asphalt binder valued at roughly 3 billion/year. The instability of the world's oil market has pushed oil prices to more than 80 per barrel in 2012, which increased the cost of asphalt binder up to $570 per ton. Therefore, there is a timely need to find alternative sustainable resources to the asphalt binder. This paper investigates the possibility of the partial replacement of the asphalt binder with slaughterhouse waste and/or fly ash. In order to achieve this objective, the asphalt binder is mixed with different percentages of waste oil and/or fly ash. In order to investigate the effect of these additives to the performance of the asphalt binder, a complete performance grade test performed on multiple samples. The results of the performance grade tests are compared with a control sample to observe how the addition of the waste oil and/or fly ash affects the sample. Considering the increasing cost and demand of asphalt, the use of slaughterhouse waste oil and/or fly ash as a partial replacement may result in environmental and monetary improvements in the transportation sector.

  8. Hot Mix Asphalt Recycling: Practices and Principles

    NARCIS (Netherlands)

    Mohajeri, M.

    2015-01-01

    Hot mix asphalt recycling has become common practice all over the world since the 1970s because of the crisis in oil prices. In the Netherlands, hot recycling has advanced to such an extent that in most of the mixtures more than 50% of reclaimed asphalt (RA) is allowed. These mixtures with such a hi

  9. EVALUATION OF EMISSIONS FROM PAVING ASPHALTS

    Science.gov (United States)

    The report provides data from pilot-scale measurements of the emissions of specific air pollutants from paving asphalt both with and without recycled crumb rubber additives. The methods used in this work measured emissions from a static layer of asphalt maintained for several hou...

  10. EVALUATION OF EMISSION FROM PAVING ASPHALTS

    Science.gov (United States)

    The report provides data from pilot-scale measurements of the emissions of specific air pollutants from paving asphalt both with and without recycled crumb rubber additives. he methods used in this work measured emissions from a static layer of asphalt maintained for several hour...

  11. Rheological Evaluation of Polymer Modiifed Asphalt Binders

    Institute of Scientific and Technical Information of China (English)

    WANG Lan; CHANG Chunqing

    2015-01-01

    The microstructure and dynamic rheological characteristics of asphalt containing different polymer modifiers (crumb rubber, styrene-butadiene-styrene and crumb rubber mix with styrene-butadiene-styrene) at mid and high service temperature levels were investigated by using scanning electron microscopy(SEM), dynamic shear rheometer(DSR) and repeat creep test. The main objective of the investigation was to rank the modifiers based on their effect on performance characteristics of asphalt under service conditions. To evaluate the effect of different modiifers on the viscoelastic response of asphalt, the temperature and frequency dependences of the dynamic viscoelastic properties were compared. The mid-temperature fatigue resistance and high-temperature rutting resistance of three polymer modiifed asphalts were evaluated to predict their ifeld performance in roads. Based on the current results, an improved rutting factor was proposed to determine the rutting resistance of asphalt pavements. In addition, the viscous stiffness (Gv), deifned as the reciprocal of viscous compliance, was used to evaluate the high-temperature deformation resistance of asphalt mixtures. The experimental results indicate that the asphalt containing crumb rubber only shows superior performance at mid and high service temperatures in all three modiifed asphalt binders due to the action of the crumb rubber.

  12. Environmental Benefits of Warm Mix Asphalt

    OpenAIRE

    Zaumanis, M; OLESEN, E

    2010-01-01

    WMA is a relatively new technology that allows significant lowering of the production and pavement temperature of conventional hot mix asphalt (HMA). It promises various benefits, but probably the most significant is the possibility to reduce carbon footprint of asphalt thus supporting the demands of Kyoto protocol for lowering greenhouse gas emissions in the atmosphere.

  13. Environmental Benefits of Warm Mix Asphalt (WMA)

    OpenAIRE

    Zaumanis, M; Olesen, E

    2010-01-01

    Warm Mix Asphalt technology promises various benefits, but probably the most significant is the possibility to reduce carbon footprint of asphalt. The degree of emission reduction depends on the production technology, therefore life cycle assessment tool is vital to calculate the benefits and compare technologies.

  14. Curing Reaction Model of Epoxy Asphalt Binder

    Institute of Scientific and Technical Information of China (English)

    QIAN Zhendong; CHEN Leilei; WANG Yaqi; SHEN Jialin

    2012-01-01

    In order to understand the strength developing law of the epoxy asphalt mixture,a curing reaction model of the epoxy asphalt binder was proposed based upon the thermokinetic analysis.Given some assumptions,the model was developed by applying the Kissinger law as well as Arrhenius equation,and the differential scanning calorimetry was performed for estimating the model parameters.To monitor the strength development of the epoxy asphalt mixture,a strength test program was employed and then results were compared to those produced from the proposed model.The comparative evaluation shows that a good consistency exists between the outputs from test program and the proposed model,indicating that the proposed model can be used effectively for simulating the curing reaction process for the epoxy asphalt binder and predicting the strength development for the epoxy asphalt mixture.

  15. Rubber-like Quasi-thermosetting Polyetheramine-cured Epoxy Asphalt Composites Capable of Being Opened to Traffic Immediately

    OpenAIRE

    Yang Kang; Qiang Wu; Rui Jin; Pengfei Yu; Jixiang Cheng

    2016-01-01

    This paper reports the facile preparation, mechanical performance and linear viscoelasticity of polyetheramine-cured rubber-like epoxy asphalt composites (EACs) with different asphalt contents. Compared with previous EACs prepared via complex chemical reactions and time-consuming high-temperature curing, the EACs reported here were obtained by using a compatible, bi-functional polyetheramine and a simple physical co-blend process, which make the EACs feasibly scalable for production at a lowe...

  16. Effects of Mineral Filler to Polymer Modified Bitumen Ratio on the Design Properties of Hot Mix Asphalt and its Performance

    OpenAIRE

    Imran Hafeez; MUMTAZ AHMED KAMAL

    2010-01-01

    Current development in the design of asphalt concrete especially in the upper layers of flexible pavements contains about acceptable proportion of mineral fillers passing 75?m (# 200) sieve, which contributes towards the mix cohesion, resistant to rutting and improves serviceability. Three filler to PMA (Polymer Modified Asphalt) ratios (i.e. 2.4, 3.4. and 4.4%) in Marshall Method of mix design were used in order to determine the optimum filler content at relatively low design ...

  17. Non-isothermal kinetics of styrene—butadiene—styrene asphalt combustion

    International Nuclear Information System (INIS)

    The combustion characteristics of styrene—butadiene—styrene (SBS) asphalt are studied by thermogravimetric analysis (TG/DTG) at four different heating rates. According to the saturates/aromatics/resins/asphaltenes (SARA) fractionation method, the combustion process of SBS asphalt can be divided by Gaussian peak fitting into three main stages: oil content release, resin pyrolysis, and asphaltene and char combustion. When the heating rate increases, the mass losses of the oil content and resin pyrolysis increase, and less asphaltenes are formed at a higher temperature. The activation energy values are calculated by the Coats—Redfern method to be in the range 61.6 kJ/mol–142.9 kJ/mol. The Popescu method is used for the kinetic analysis, and the result shows that the three stages of asphalt combustion can be explained by the sphere phase boundary reaction model, the second order chemical reaction model, nucleation, and its subsequent growth model, respectively

  18. USE OF RECLAIMED ASPHALT PAVEMENT WITH MILLED ROAD PAVEMENT LAYERS

    Directory of Open Access Journals (Sweden)

    Andrzej Plewa

    2015-07-01

    Full Text Available The article presents the results of research on the functional properties of asphalt mixes using RAP obtained from milling asphalt road pavements. Asphalt concrete AC 22P with 0%, 10%, 15% and 20% addition of RAP used for base course of road pavements were designed. It was found that asphalt mixes with RAP characterized by comparable and in some cases better functional properties compared to the asphalt mixes without RAP (0%. One should notice the influence of RAP on the performance and durability of the asphalt mixtures, as compared to virgin asphalt mixtures (without RAP.

  19. Representative volume element of asphalt pavement for electromagnetic measurements

    Directory of Open Access Journals (Sweden)

    Terhi Pellinen

    2015-02-01

    Full Text Available The motivation for this study was to investigate the representative volume element (RVE needed to correlate the nondestructive electromagnetic (EM measurements with the conventional destructive asphalt pavement quality control measurements. A large pavement rehabilitation contract was used as the test site for the experiment. Pavement cores were drilled from the same locations where the stationary and continuous Ground Penetrating Radar (GPR measurements were obtained. Laboratory measurements included testing the bulk density of cores using two methods, the surface-saturated dry method and determining bulk density by dimensions. Also, Vector Network Analyzer (VNA and the through specimen transmission configuration were employed at microwave frequencies to measure the reference dielectric constant of cores using two different footprint areas and therefore volume elements. The RVE for EM measurements turns out to be frequency dependent; therefore in addition to being dependent on asphalt mixture type and method of obtaining bulk density, it is dependent on the resolution of the EM method used. Then, although the average bulk property results agreed with theoretical formulations of higher core air void content giving a lower dielectric constant, for the individual cores there was no correlation for the VNA measurements because the volume element seizes deviated. Similarly, GPR technique was unable to capture the spatial variation of pavement air voids measured from the 150-mm drill cores. More research is needed to determine the usable RVE for asphalt.

  20. Evaluation of Colemanite Waste as Aggregate Hot Mix Asphalt Concrete

    Directory of Open Access Journals (Sweden)

    Nihat MOROVA

    2015-09-01

    Full Text Available In this study usability of waste colemanite which is obtained after cutting block colemanite for giving proper shape to blocks as an aggregate in hot mix asphalt. For this aim asphalt concrete samples were prepared with four different aggregate groups and optimum bitumen content was determined. First of all only limestone was used as an aggregate. After that, only colemanite aggregate was used with same aggregate gradation. Then, the next step of the study, Marshall samples were produced by changing coarse and fine aggregate gradation as limestone and colemanite and Marshall test were conducted. When evaluated the results samples which produced with only limestone aggregate gave the maximum Marshall Stability value. When handled other mixture groups (Only colemanite, colemanite as coarse aggregate-limestone as fine aggregate, colemanite as fine aggregate-limestone as coarse aggregate all groups were verified specification limits. As a result, especially in areas where there is widespread colemanite waste, if transportation costs did not exceed the cost of limestone, colemanite stone waste could be used instead of limestone in asphalt concrete mixtures as fine aggregate

  1. Energy and exergy analysis in an asphalt plant's rotary dryer

    International Nuclear Information System (INIS)

    In this paper, energy and exergy analyses of a rotary dryer employed in a Hot Mix Asphalt (HMA) plant for heating and drying of the aggregates in the mixture is presented. In the analysis, the exergy method in addition to the more conventional energy analysis, is employed to identify and evaluate the thermodynamic losses. The results show that, at design conditions, the plant performs with energy and exergy efficiencies of 0.89 and 0.18, respectively. The energy losses are mainly due to the flue gases. The exergy distribution indicates that the combustion and the heat transfer at different temperatures in the burner yield the highest exergy destruction in the process. A parametric study is conducted for the plant under various operational production parameters, including different humidities of the aggregates and filler content in aggregates, working temperatures and ambient conditions, in order to determine the parameters that affect the plant performance. It is shown that the solids humidity has a great impact on energy requirements. A better and sustainable use of the heat source employed in the dryer is proposed to avoid the high irreversibilities found. Furthermore, operating corrections in the mix or in the exhaust gas temperature are proposed to optimize the performance of the plant. - Research highlights: → Identify main energy losses and irreversibilities in the dryer of an asphalt plant. → Optimize operating conditions in an Asphalt plant. → Improve energy savings and availability of the drying and heating process. → Encourage the use of a cogeneration system.

  2. An Evaluation of the Delayed-Coking Product Yield of Heavy Feedstocks Using Asphaltene Content and Carbon Residue Évaluation du rendement en produit de cokéfaction différée de pétrole lourd à l'aide de la teneur an asphaltènes et du résidu de coke

    Directory of Open Access Journals (Sweden)

    Schabron J. F.

    2006-11-01

    Full Text Available Six residua from different crude oils were evaluated for composition and carbon residue forming tendencies. The whole residua were evaluated for elemental composition, trace metals content, carbon residue, and specific gravity. Each residuum was deasphaltened in heptane, and the heptane-soluble materials were separated into saturate, aromatic, and polar fractions on activated silica gel. The asphaltenes were evaluated for elemental composition, trace metals content, molecular weight, and carbon residue. The relationship between carbon residues and features of the asphaltenes was studied, and a correlation of contributing features was developed. The asphaltenes were further separated into four fractions according to apparent molecular size by preparative size exclusion chromatography (SEC. The preparative size exclusion chromatographic fractions from the asphaltenes were evaluated for sulfur content, molecular weight, and trace metals content. Material balances showed that the data obtained on the fractions account for the data obtained on the original material. This indicates that the contributions of the properties of the fractions can be studied and related to properties of the whole material. La composition et le résidu de coke de six résidus de raffinage de différents pétroles lourds ont été évalués afin de déterminer des tendances. La composition élémentaire, la teneur en métaux-traces, le résidu de coke et la densité spécifique ont été déterminés sur le résidu complet. Chaque résidu a été désasphalténé dans l'heptane et les produits solubles dans l'heptane ont été séparés en fractions saturée, aromatique et polaire sur du gel de silice activée. La composition élémentaire, la teneur en métaux-traces, la masse moléculaire et le résidu de coke ont été déterminés sur les asphaltènes. La relation entre les résidus de coke et les caractéristiques des asphaltènes a été étudiée, ce qui a permis d

  3. Strength Mechanism and Influence Factors for Cold Recycled Asphalt Mixture

    OpenAIRE

    Tao Ma; Hao Wang; Yongli Zhao; Xiaoming Huang; Yuhui Pi

    2015-01-01

    This study focused on the key factors affecting the tensile strength of cold recycled asphalt mixture with cement and emulsified asphalt. The specific surface areas and strength of RAP were analyzed. The interaction between the emulsified asphalt and cement was observed. Comprehensive laboratory testing was conducted to evaluate the influences of RAP, emulsified asphalt, and cement on the tensile strength of cold recycled asphalt mixture. It is found that although RAP is used as aggregates, i...

  4. USE OF RECLAIMED ASPHALT PAVEMENT WITH MILLED ROAD PAVEMENT LAYERS

    OpenAIRE

    Andrzej Plewa; Marta Wasilewska; Władysław Gardziejczyk; Paweł Gierasimiuk

    2015-01-01

    The article presents the results of research on the functional properties of asphalt mixes using RAP obtained from milling asphalt road pavements. Asphalt concrete AC 22P with 0%, 10%, 15% and 20% addition of RAP used for base course of road pavements were designed. It was found that asphalt mixes with RAP characterized by comparable and in some cases better functional properties compared to the asphalt mixes without RAP (0%). One should notice the influence of RAP on the performance and ...

  5. Investigation of mineral filler effects on the aging process of asphalt mastics

    Science.gov (United States)

    Moraes, Raquel

    Aging of asphalt binders is induced by chemical and/or physicochemical changes during production of pavement and throughout its service life. Although binder aging in pavement always occurs while binder is in contact with aggregates and mineral filler, in most laboratory aging studies, and in current specifications, asphalt binders are individually aged without accounting for aggregate induced interactions. Past research has had conflicting findings, attributing both mitigating and/or catalytic effects to the presence of mineral filler in asphalt binder with regards to oxidative aging. Thus, in the present study it was hypothesized that evaluation of asphalt oxidative aging without regard to interactive effect of the presence of mineral filler is inadequate as a specification tool. Effects of mineral fillers on oxidative aging of asphalt is investigated by means of accelerated aging of mastics (asphalt and fillers) in Pressure Aging Vessel (PAV). Testing matrix included aging evaluation of mastics containing different fillers content, mineralogy, and surface area. Results showed that low-temperature behavior of aged mastic can be modified by controlling filler concentration and type. Fillers acts as an agent adsorbing heavy fractions of asphalt binder, therefore reducing stiffness and changing glass-transition temperature. Also, during oxidative aging of asphalt binders and mastics, both diffusion and adsorption mechanisms play a role in the rate of aging of asphaltic material. A method to characterize the behavior of mastics with aging was also developed by monitoring the mastics |G*| aging index (ratio of complex modulus before and after aging). Gel Permeation Chromatography (GPC) testing results supported mentioned findings regarding |G*| changes, as the presence of mineral filler appears to decelerate the rate of production of larger molecular size oxidation products in the binder phase of mastics. Implication of the findings is that change in molecular size

  6. Scrap tire rubber as modifier of asphalt cement for use in road paving Borracha de pneus como modificador de cimentos asfálticos para uso em obras de pavimentação

    OpenAIRE

    Sandra Oda; Jose Leomar Fernandes Junior

    2001-01-01

    This work presents the results of a research on the technical feasibility of the use of asphalt-rubber binder by the asphalt paving industry. In Brazil more than 30 million tires a year are disposed of, mostly in inadequate sites, causing serious health and environmental problems. The effects of the main factors (rubber content, rubber particle size, temperature of mixture, reaction time) on the behavior of asphalt-rubber binders are evaluated by traditional and Superpave Method tests, the la...

  7. Fatigue behavior of asphalt mixtures colombian with addition recycled pavement asphalt to 100 %

    Directory of Open Access Journals (Sweden)

    Neidy Betssey Patiño Boyacá

    2015-01-01

    Full Text Available This research was conducted in order to establish the fatigue behavior of asphalt mixtures with gradations MD20 Instituto de Desarrollo Urbano (IDU and MDC 2 of The Instituto Nacional de Vías (INVIAS, with addition of recycled granular flexible pavement (RAP with asphalt of penetration 60/70 and 80/100. The first step was to characterize the asphalt and RAP as well as calculate the optimum percentage of asphalt to be added to 100 % RAP mixtures. Then samples were fabricated with different trapezoidal gradations and asphalt, to be tested finally fatigue at different deformations. Among the results found, it was determined that the tested mixtures have a high stiffness; although, it varies depending on the asphalt mix used and that the best fatigue life with respect to those studied is the MDC-2 with bitumen 80/100.

  8. Using Pyrolized Carbon Black (PCB) from Waste Tires in Asphalt Pavement (Part 2, Asphalt Binder)

    OpenAIRE

    Zeng, Yongdong; Lovell, C. W.

    1996-01-01

    Scrap tires derived from automobiles have become a large environmental problem in the United States. In this study, research is carried out to investigate the potential use of tire-derived pyrolyzed carbon black from scrap tires as an asphalt cement modifier. The asphalt cements used in this research were AC10 and AC20. Penetration and softening point tests were performed to obtain the consistency of the asphalt cements. The pyrolyzed carbon black, as provided by Wolf Industries, was comb...

  9. Microstructural Analysis and Rheological Modeling of Asphalt Mixtures Containing Recycled Asphalt Materials

    OpenAIRE

    Augusto Cannone Falchetto; Ki Hoon Moon; Michael P. Wistuba

    2014-01-01

    The use of recycled materials in pavement construction has seen, over the years, a significant increase closely associated with substantial economic and environmental benefits. During the past decades, many transportation agencies have evaluated the effect of adding Reclaimed Asphalt Pavement (RAP), and, more recently, Recycled Asphalt Shingles (RAS) on the performance of asphalt pavement, while limits were proposed on the amount of recycled materials which can be used. In this paper, the eff...

  10. Behaviour of asphalt rubber mixtures with different crumb rubber and asphalt binder sources

    OpenAIRE

    Fontes, Liseane P. T. L.; Pereira, Paulo A. A.; Pais, Jorge C.; Trichês, Glicério

    2006-01-01

    This study evaluates the performance in laboratory of gap graded mixture prepared with different crumb rubber types and different conventional grade asphalt binders. The asphalt rubbers were prepared via wet process (continuous blend) and their properties were measured through the current tests: (i) penetration;(ii) softening point: (iii) resilience; (iv) apparent viscosity using a Brookfield viscometer. The rheological properties for conventional asphalts were measured too, in order to evalu...

  11. Physical properties of asphalt rubber after being mixed with reclaimed asphalt mixes

    OpenAIRE

    Pais, Jorge C.; Pereira, Paulo A. A.; Junior, J.; Gardete, Dinis

    2008-01-01

    Recycling of road pavements became an effective technique after the European legislation defined the amount of reclaimed material that could be sent to landfills. This rehabilitation technique allows the re-use of old pavement material and favours the reduction of the amount of new materials used to produce new pavement layers. One of the most promising pavement rehabilitation techniques uses asphalt rubber mixtures, i.e. asphalt mixtures in which the binder is asphalt modified by crumb r...

  12. Investigating In Situ Properties of Recycled Asphalt Pavement with Foamed Asphalt as Base Stabilizer

    OpenAIRE

    Antonis Kaltsounis; Vasilis Papavasiliou; Andreas Loizos; Christina Plati

    2010-01-01

    The objective of the present study was to conduct a comprehensive field experiment for the in situ assessment of in-depth recycled asphalt pavement using foamed asphalt as a stabilization treatment for base works. For this purpose Nondestructive Testing (NDT) data collected using the Falling Weight Deflectometer (FWD) and Ground Penetrating Radar (GPR) along a foamed asphalt recycled pavement section was thoroughly analysed. Critical issues including the stabilized material curing and the con...

  13. The Use of Polyethylene in Hot Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Mohammad T. Awwad

    2007-01-01

    Full Text Available The increase in road traffic during the last two decades in combination with an insufficient degree of maintenance due to shortage in funds has caused an accelerated and continuous deterioration of the road network in Jordan. To alleviate this process, several types of measures may be effective, e.g., securing funds for maintenance, improved roadway design, use of better quality of materials and the use of more effective construction methods. The use of polymer in asphalt mixture as a modifier started in the 80s of the last century and has been tested in a number of countries around the World. In this research, polyethylene as one sort of polymers is used to investigate the potential prospects to enhance asphalt mixture properties. The objectives also include determining the best type of polyethylene to be used and its proportion. Two types of polyethylene were added to coat the aggregate [High Density Polyethylene (HDPE and Low Density Polyethylene (LDPE]. The polymers were introduced to the mixture in two states (Grinded and not Grinded. Marshall mix design was used, first to determine the optimum bitumen binder content and then further to test the modified mixture properties. In total, 105 samples were prepared (21 samples were used to determine the binder content and the remaining samples were used to investigate the effect of modifying the asphalt mixtures. The optimum asphalt content was 5.4%. Seven proportions of polyethylene of each type and state by weight of the optimum binder content were selected to be tested (6, 8, 10, 12, 14, 16 and 18%. The tests include the determination of bulk density, stability and flow. Marshall mix design requires the determination of the percentages of air voids and air voids of mineral aggregate. The results indicated that grinded HDPE polyethylene modifier provides better engineering properties. The recommended proportion of the modifier is 12% by the weight of bitumen content. It is found to increase the

  14. Change in fatigue behavior of asphalt hot mixes produced with asphalt rubber binders

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Farias, Márcio Muniz de; Pais, Jorge C.

    2009-01-01

    Fatigue life of asphalt hot mixes is given as a function of both stiffness and tensilestrains induced in the bottom of the wearing courses of flexible pavements. In conventional as-phalt hot mixes the increase of stiffness leads to a decrease of fatigue life. However, this work shows that there is an increase of both fatigue life and stiffness of asphalt rubber hot mixes in comparison with the asphalt hot mixes produced with straight binders. In this work laboratory tests were performed in as...

  15. Effects of asphalt rejuvenator on thermal and mechanical properties on oxidized hot mixed asphalt pavements

    Science.gov (United States)

    Farace, Nicholas A.; Buttlar, William G.; Reis, Henrique

    2016-04-01

    The utilization of asphalt rejuvenator, and its effectiveness for restoring thermal and mechanical properties was investigated via Disk-shaped Compact Tension (DC(T)) and acoustic emission (AE) testing for determining mechanical properties and embrittlement temperatures of the mixtures. During the DC(T) testing the fracture energies and peak loads were used to measure the resistance of the rejuvenated asphalt to low temperature cracking. The AE testing monitored the acoustic emission activity while the specimens were cooled from room temperature to -40 °C to estimate the temperature at which thermal cracking began (i.e. the embrittlement temperature). First, a baseline response was obtained by obtaining the mechanical and thermal response of virgin HMA samples and HMA samples that had been exposed to oxidative aging for 36 hours at 135°C. The results showed the virgin samples had much higher peak loads and fracture energies than the 36 hours aged samples. Acoustic Emission showed similar results with the virgin samples having embrittlement temperatures 10 °C cooler than the 36 hours aged specimens. Then, overaged for 36 hours specimens were treated different amounts of rejuvenator (10%, 15%, and 20% by weight of binder content) and left to dwell for increased amount of time periods varying from one to eight weeks. It was observed that the AE results showed an improvement of embrittlement temperature with increasing with the dwell times. The 8 weeks specimens had cooler embrittlement temperatures than the virgin specimens. Finally, the low temperature effects on fracture energy and peak load of the rejuvenated asphalt was investigated. Rejuvenator was applied (10% by weight of binder) to specimens aged 36 hours at 135 °C, and the dwell time was varied from 1 to 4 weeks. The results showed that the peak loads were restored to levels of the virgin specimens, and the fracture energies improved to levels beyond that of the virgin specimens. The results also showed a

  16. Assessment of dynamic modulus of high density polypropylene waste fiber reinforcement in asphalt concrete

    Directory of Open Access Journals (Sweden)

    Hassan S. OTUOZE

    2015-12-01

    Full Text Available Traditional asphalt tests like Hveem and Marshall tests are at best mere characterization than effective test of pavement field performance because of complex viscoelastic behavior of asphalt. Mechanical properties otherwise called simple performance tests (SPT are performance criteria of asphalt. Dynamic modulus among other SPT’s like permanent deformation, fatigue cracking, thermal cracking, moisture susceptibility, shear and friction properties; determines stress-strain to time-temperature relationships that imparts on strength, service life and durability. The test followed the recommendations of NCHRP 1-37a (2004 and mixes were prepared using 0, 0.5, 1.0 and 1.5% HDPP contents. The parameters tested for dynamic modulus, /E*/, are stiffness, recoverable strain (ε, and phase angle (ξ. Time – temperature superposition (TTS called master curve was fitted using sigmoidal curve to interpolate the parameters beyond measured data set so as to observe the viscoelastic behavior outside the physical properties. The performance of 0.5% HDPP asphalt is better enhanced than the conventional asphalt to improve upon strength, service and durability.

  17. Addition of an industrial residue to asphalt: evaluation of material properties

    Energy Technology Data Exchange (ETDEWEB)

    Dantas, T.N. Castro; Lima, C.K.M.; Moura, M.C.P.A.; Dantas Neto, A.A.; Felix, G.B. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil). Dept. de Engenharia Quimica], e-mail: carlenise@eq.ufrn.br

    2010-10-15

    Polymer waste from a button manufacturer was blended with 50/60 penetration-grade petroleum asphalt cement with the purpose of enhancing its physical properties and to obtain pavements which are more resistant to temperature gradients and permanent deformation. This polymer waste is considered as an environmental problem because it is produced in large scale and stored in sanitary landfills. First, the polymer waste was classified as unsaturated polyester. Then, the waste was blended with asphalt according to the following experimental conditions: polymer content: 2.0, 7.0, or 14.0 wt.%; mixing temperature: 140 or 180 deg C; and mixing time: 20 or 60 min. The results obtained in penetration index, ring-and-ball softening point, flash point, and viscosity assays showed that the addition of polymer waste as an insoluble material to asphalt is a viable alternative to solve this environmental problem. (author)

  18. Method of reprocessing radioactive asphalt solidification products

    International Nuclear Information System (INIS)

    Purpose: To obtain heat-stable solidification products and decrease the total volume thereof by modifying the solidified form by the reprocessing of existent radioactive asphalt solidification products. Method: Radioactive asphalt solidification products are heated into a fluidized state. Then, incombustible solvents such as perchloroethylene or trichloroethylene are added to a dissolving tank to gradually dissolve the radioactive asphalt solidification products. Thus, organic materials such as asphalts are transferred into the solvent layer, while inorganic materials containing radioactive materials remain as they are in the separation tank. Then, the inorganic materials containing the radioactive materials are taken out and then solidified, for example, by converting them into a rock or glass form. (Kawakami, Y.)

  19. Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modeling

    Science.gov (United States)

    Safaei, Farinaz; Castorena, Cassie; Kim, Y. Richard

    2016-04-01

    Fatigue cracking is a major form of distress in asphalt pavements. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design mixtures and pavements that are not susceptible to premature fatigue failure. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. In this study, the S-VECD model, developed for asphalt mixtures, is adapted for asphalt binders tested under cyclic torsion in a dynamic shear rheometer. Derivation of the model framework is presented. The model is verified by producing damage characteristic curves that are both temperature- and loading history-independent based on time sweep tests, given that the effects of plasticity and adhesion loss on the material behavior are minimal. The applicability of the S-VECD model to the accelerated loading that is inherent of the linear amplitude sweep test is demonstrated, which reveals reasonable performance predictions, but with some loss in accuracy compared to time sweep tests due to the confounding effects of nonlinearity imposed by the high strain amplitudes included in the test. The asphalt binder S-VECD model is validated through comparisons to asphalt mixture S-VECD model results derived from cyclic direct tension tests and Accelerated Loading Facility performance tests. The results demonstrate good agreement between the asphalt binder and mixture test results and pavement performance, indicating that the developed model framework is able to capture the asphalt binder's contribution to mixture fatigue and pavement fatigue cracking performance.

  20. Linking asphalt binder fatigue to asphalt mixture fatigue performance using viscoelastic continuum damage modeling

    Science.gov (United States)

    Safaei, Farinaz; Castorena, Cassie; Kim, Y. Richard

    2016-08-01

    Fatigue cracking is a major form of distress in asphalt pavements. Asphalt binder is the weakest asphalt concrete constituent and, thus, plays a critical role in determining the fatigue resistance of pavements. Therefore, the ability to characterize and model the inherent fatigue performance of an asphalt binder is a necessary first step to design mixtures and pavements that are not susceptible to premature fatigue failure. The simplified viscoelastic continuum damage (S-VECD) model has been used successfully by researchers to predict the damage evolution in asphalt mixtures for various traffic and climatic conditions using limited uniaxial test data. In this study, the S-VECD model, developed for asphalt mixtures, is adapted for asphalt binders tested under cyclic torsion in a dynamic shear rheometer. Derivation of the model framework is presented. The model is verified by producing damage characteristic curves that are both temperature- and loading history-independent based on time sweep tests, given that the effects of plasticity and adhesion loss on the material behavior are minimal. The applicability of the S-VECD model to the accelerated loading that is inherent of the linear amplitude sweep test is demonstrated, which reveals reasonable performance predictions, but with some loss in accuracy compared to time sweep tests due to the confounding effects of nonlinearity imposed by the high strain amplitudes included in the test. The asphalt binder S-VECD model is validated through comparisons to asphalt mixture S-VECD model results derived from cyclic direct tension tests and Accelerated Loading Facility performance tests. The results demonstrate good agreement between the asphalt binder and mixture test results and pavement performance, indicating that the developed model framework is able to capture the asphalt binder's contribution to mixture fatigue and pavement fatigue cracking performance.

  1. Assessment of bond between asphalt layers

    OpenAIRE

    Muslich, Sutanto

    2010-01-01

    Asphalt pavements are usually constructed in several layers and most of pavement design and evaluation techniques assume that adjacent asphalt layers are fully bonded together and no displacement is developed between them. However, full bonding is not always achieved and a number of pavement failures have been linked to poor bond condition Theoretical research showed that the distribution of stresses, strains and deflections within the pavement structure is highly influenced by the bond c...

  2. ALGORITHM OF CHOOSING ASPHALT MIXING PLANTS

    OpenAIRE

    Zhukov, P.; Kravchuk, Y.; Zhukov, D.

    2010-01-01

    The development of transport infrastructure, which must conform to European standards and in its turn requires the development of road economy, is one of the ways out of the crisis. The development of road economy requires either construction of asphalt-concrete mixture plants or their modernization, or reconstruction of existing plants. Any reconstruction or modernization and, moreover, construction of new asphalt-concrete plants requires the optimization of choosing the most efficient aspha...

  3. Performance Characteristics of Silane Silica Modified Asphalt

    OpenAIRE

    Xuedong Guo; Mingzhi Sun; Wenting Dai; Shuang Chen

    2016-01-01

    At present there are many kinds of fillers and modifier used for modified asphalt, but the effect of modifier differs in thousands of ways; most of them can increase the high temperature performance of asphalt, but the modified effect of low-temperature crack resistance, water stability, and antifatigue performance is different. Aiming at the subsistent problems, this paper innovatively puts forward the idea of taking the silane silica (nanosilica modified with silane coupling agent) as fille...

  4. Safety evaluation of asphalt products, (1)

    International Nuclear Information System (INIS)

    The safety of activity-containing asphalt products kept in enclosed storage was evaluated from considerations of radiolysis and hydrogen evolution. The samples examined were mainly homogeneous asphalt products containing 43w/0 of sludge produced in routine operation of the asphalt plant at the Japan Atomic Energy Research Institute (JAERI), the samples were irradiated with external 60Co γ-ray source to a dose of 109 R. The bulk of the gases evolving from the asphalt product is hydrogen, which constitutes 75 -- 95% of the total gas evolution. The total amount of gases generated during infinite time is proportional to the total exposure dose; hydrogen evolves at a rate of 5.5x10-3 cm3/g.MR. The amount of total gas evolution is governed solely by the quantity of asphalt, and is independent of the sludge contained therein. Nor do differences in the rate of dose appear to have any significant effect. In so far as concerns smallness of radiolysis, slightly better performance can be expected from straight than from blown asphalt. There is no danger of explosion of the asphalt products currently generated at JAERI (10-5 Ci/kg), which can be expected to accumulate in infinite time no more than about 3 cm3 from a 200 l product. Only asphalt products containing activity in concentrations exceeding 10-1 Ci/kg risk explosion when kept in enclosed storage, through accumulation of hydrogen in quantity exceeding the explosion limit in a relatively short time. (auth.)

  5. Rapid determination of actinides in asphalt samples

    International Nuclear Information System (INIS)

    A new rapid method for the determination of actinides in asphalt samples has been developed that can be used in emergency response situations or for routine analysis. If a radiological dispersive device, improvised nuclear device or a nuclear accident such as the accident at the Fukushima Nuclear Power Plant in March, 2011 occurs, there will be an urgent need for rapid analyses of many different environmental matrices, including asphalt materials, to support dose mitigation and environmental clean-up. The new method for the determination of actinides in asphalt utilizes a rapid furnace step to destroy bitumen and organics present in the asphalt and sodium hydroxide fusion to digest the remaining sample. Sample preconcentration steps are used to collect the actinides and a new stacked TRU Resin + DGA Resin column method is employed to separate the actinide isotopes in the asphalt samples. The TRU Resin plus DGA Resin separation approach, which allows sequential separation of plutonium, uranium, americium and curium isotopes in asphalt samples, can be applied to soil samples as well. (author)

  6. Rheological properties of asphalts with particulate additives

    Energy Technology Data Exchange (ETDEWEB)

    Shashidhar, N. [EBA Engineering, Baltimore, MD (United States); Chollar, B.H. [Federal Highway Administration, McLean, VA (United States)

    1996-12-31

    The Superpave asphalt binder specifications are performance-based specifications for purchasing asphalt binders for the construction of roads. This means that the asphalt is characterized by fundamental material (rheological) properties that relate to the distress modes of the pavements. The distress modes addressed are primarily rutting, fatigue cracking and low temperature cracking. For example, G*/sin({delta}) is designed to predict the rutting potential of pavements, where G* is the magnitude of the complex shear modulus and 6 is the phase angle. The binder for a road that is situated in a certain climatic zone requires the binder to have a minimum G*/sin({delta}) of 2200 Pa at the highest consecutive 7-day average pavement temperature the road had experienced. Implicit in such a performance based specification is that the fundamental property, G*/sin({delta}), of the binder correlates with rutting potential of the pavement regardless of the nature of the binder. In other words, the specification is transparent to the fact that the binder can simply be an asphalt, or an asphalt modified by polymers, particulates and other materials that can form a two-phase mixture. This paper discusses the asphalt-particulate system.

  7. Effects of Crumb Rubber Size and Concentration on Performance of Porous Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Altan Cetin

    2013-01-01

    Full Text Available The purpose of this study is to investigate the effect of size distribution and concentration of crumb rubber on the performance characteristics of porous asphalt mixture. The recycling of scrap tires in asphalt pavements appears as an important alternative providing a large-scale market. The characteristics of bitumen are very important with regard to service life of porous asphalt pavement. The experimental study consists of two main steps. Firstly, the mixture design was performed to determine the optimum bitumen content. In the latter step, the mixtures were modified by dry process using crumb rubber in three different grain size distributions of #4~#20, #20~#200, and #4~#200 and rubber content of 10%, 15%, and 20% as weight of optimum bitumen. The permeability, Cantabro abrasion loss, indirect tensile strength, moisture susceptibility, and resilient modulus tests were carried out on the specimens. Test results show that #20~#200 sized rubber particles reduced air voids and coefficient of permeability, while they increased the Cantabro abrasion loss. In general, increasing the crumb rubber size and content decreased the performance characteristics of the porous asphalt mixtures.

  8. Effects of reclaimed asphalt pavement on indirect tensile strength test of conditioned foamed asphalt mix

    International Nuclear Information System (INIS)

    This paper presents the results of Indirect Tensile Strength (ITS) Test for samples prepared with reclaimed asphalt pavement (RAP). Samples were conditioned in water at 25°C for 24 hours prior to testing. Results show that recycled aggregate from reclaimed asphalt pavement performs as well as virgin aggregate.

  9. Effects of reclaimed asphalt pavement on indirect tensile strength test of conditioned foamed asphalt mix

    Science.gov (United States)

    Yati Katman, Herda; Rasdan Ibrahim, Mohd; Yazip Matori, Mohd; Norhisham, Shuhairy; Ismail, Norlela

    2013-06-01

    This paper presents the results of Indirect Tensile Strength (ITS) Test for samples prepared with reclaimed asphalt pavement (RAP). Samples were conditioned in water at 25°C for 24 hours prior to testing. Results show that recycled aggregate from reclaimed asphalt pavement performs as well as virgin aggregate.

  10. Asphalte

    OpenAIRE

    Foley, S.

    1987-01-01

    The Burnett Archive of Working Class Autobiographies was gathered together by John Burnett, David Vincent and David Mayall whilst compiling their three volumes annotated bibliography, "The Autobiography of the Working Class" (Harvester Press, 1984-1989). This book includes descriptions of unpublished autobiographies and indicates their locations. Excerpts from some of the autobiographies have been published in "Destiny obscure: autobiographies of childhood, education, and family from the1820s...

  11. Gray Correlation Analysis on the Relationship Between Colloidal Structure and Chemical Component of Asphalt Colloid and Performance

    Directory of Open Access Journals (Sweden)

    X. J. Cao

    2015-01-01

    Full Text Available Asphalt is considered a colloidal material and it is important to study the relationship between its colloidal structure, chemical components and performance. The aromatic nucleus content of asphalt at different depth analysed by attenuated total reflection (ATR was taken as the index of colloid structure. The gray correlation was used to analyse the relationship between colloidal structure and chemical components of asphalt gel and performance. The results show that the correlation degree between the index of colloidal structure and saturates and resins is high, which proves that saturates and resins play an important role in asphalt colloid structure. With regard to the asphalt performance indexes, the complex modulus G* and the tangent of the phase angle (tan δ have good correlation with the index of colloidal structure at the temperature of 30 – 70 °C but poor correlation at the temperature of 70 – 90 °C. Low temperature performance has a good correlation with colloid structure index, and tg can better reflect the characteristics of colloidal structure. The analysis shows that the colloidal structure of asphalt is a complex system and it is necessary to use more than one index to characterize the performance.

  12. Experimental studies of biodegradation of asphalt by microorganisms

    International Nuclear Information System (INIS)

    On the geological disposal system of the radioactive wastes, the activities of the microorganisms that could degrade the asphalt might be significant for the assessment of the system performance. As the main effects of the biodegradation of the asphalt, the fluctuation of leaching behavior of the nuclides included in asphalt waste has been indicated. In this study, the asphalt biodegradation test was carried out. The microorganism of which asphalt degradation ability was comparatively higher under aerobic condition and anaerobic condition was used. The asphalt biodegradation rate was calculated and it was evaluated whether the asphalt biodegradation in this system could occur. The results show that the asphalt biodegradation rate under anaerobic and high alkali condition will be 300 times lower than under aerobic and neutral pH. (author)

  13. COLOR ASPHALT CONCRETE COATING ON POLIMER-TAR BINDER

    OpenAIRE

    Zolotarev, V.; Golovenchic, S.; Oksak, S.; S. Efremov

    2005-01-01

    The possibility of receiving of color asphalt concrete on polimer-tar binder is found. Principal moments of production technology of coloured mixtures and device of asphalt concrete coating have been revealed.

  14. Modification of Asphalt by the Use of Crumb Rubber

    OpenAIRE

    Shah Room; Muhammad Aleem; Muhammad Ahmad Rana; Umair Anwar Awan; Sajjad Ali

    2014-01-01

    Health aspects enforced to ponder a study on asphalt which incorporate rubber crumbs to increase strength and flexibility of asphalt. Disposal of waste tires is a menace and it’s a serious problem globally because it is not easily biodegradable as these tires consume large spaces, open burning cause serious problems. By the use of rubber tires, this scrap is utilized efficiently and reduces the cost of asphalt to produce economical system. The asphalt is absorbed by the rubber par...

  15. Effects of preparation process on performance of rubber modified asphalt

    Science.gov (United States)

    Liu, Hanbing; Luo, Guobao; Wang, Xianqiang; Jiao, Yubo

    2015-06-01

    The rational utilization of waste rubber tire is essential for the environmental protection. Utilizing rubber particles to modify asphalt can not only improve asphalt performance, but also help the recycling of waste materials. Considering the effect of different preparation process parameters on the performance of rubber modified asphalt, this paper analyzes the effects of the shear temperature, shear time and shear rate on the performance of rubber modified asphalt, and provided a reference for its preparation.

  16. Reinforcing Effects of Carbon Black on Asphalt Binder for Pavement

    OpenAIRE

    Yamaguchi, Katsuyuki; Sasaki, Iwao; Nishizaki, Itaru; Meiarashi, Seishi; Moriyoshi, Akihiro

    2005-01-01

    Carbon black, used as a reinforcing filler for rubber materials, was evaluated for asphalt binders in pavements. Carbon black added to straight asphalt within 20 wt% caused an increase in the elastic modulus and a decrease in the viscosity of the asphalt, especially at temperatures higher than room temperature. Addition of carbon black raised the maximum service temperature of asphalt in the category of the binder performance grade according to the SHRP (Strategic Highway Research Program) sp...

  17. Influence of crumb rubber gradation on asphalt-rubber properties

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Márcio Muniz de; Pais, Jorge C.; Pereira, Paulo A. A.

    2006-01-01

    Asphalt rubber is a material produced by the incorporation of crumb rubber obtained from ground tires in straight asphalt and its properties are influenced by the components properties. The crumb rubber gradation is one of the variables which have a significant influence on asphalt rubber properties. Thus, this work studies the influence of crumb rubber gradation on the asphalt rubber properties expressed by penetration, rotational viscosity (using the Brookfield viscometer), r...

  18. Biodegradation of Asphalt Cement-20 by Aerobic Bacteria

    OpenAIRE

    Pendrys, John P.

    1989-01-01

    Seven gram-negative, aerobic bacteria were isolated from a mixed culture enriched for asphalt-degrading bacteria. The predominant genera of these isolates were Pseudomonas, Acinetobacter, Alcaligenes, Flavimonas, and Flavobacterium. The mixed culture preferentially degraded the saturate and naphthene aromatic fractions of asphalt cement-20. A residue remained on the surface which was resistant to biodegradation and protected the underlying asphalt from biodegradation. The most potent asphalt-...

  19. Theoretic computing model of combustion process of asphalt smoke

    Institute of Scientific and Technical Information of China (English)

    HUANG Rui; CHAI Li-yuan; HE De-wen; PENG Bing; WANG Yun-yan

    2005-01-01

    Based on the data and methods provided by research literature, dispersing mathematical model of combustion process of asphalt smoke is set by theoretic analysis. Through computer programming, the dynamic combustion process of asphalt smoke is calculated to simulate an experimental model. The computing result shows that the temperature and the concentration of asphalt smoke influence its burning temperature in approximatively linear manner. The consumed quantity of fuel to ignite the asphalt smoke needs to be measured from the two factors.

  20. Low Temperature Performance of Wax Modified Mastic Asphalt

    OpenAIRE

    Butt, Ali Azhar

    2009-01-01

    The current interest in energy saving asphalt production techniques is great and several new processes have been developed to reduce the mixing and compaction temperatures for hot mix asphalt. In particular, mastic asphalt products (Gussasphalt) require high working temperatures, and harder requirements concerning bitumen fumes and carbon dioxide emissions have been introduced for such products. Consequently, the need of a new means of producing and placing mastic asphalt at lower temperature...

  1. Laboratory mix design of asphalt mixture containing reclaimed material

    OpenAIRE

    Davide Lo Presti; Rawid Khan; Norhidayah Abdul Hassan; Gordon Airey; Andrew Collop

    2014-01-01

    This paper presents a study on the production of asphalt test specimens in the laboratory containing reclaimed asphalt. The mixtures considered were stone mastic asphalt concrete mixtures containing up to 30% of reclaimed asphalt. Specimens were compacted to the reference density obtained from the Marshall mix design. Gyration compaction method was used for preparing specimens for the experimental programme, while coring and cutting methods and X-ray computed tomography (CT) were used to inve...

  2. The use of crumb rubber in asphalt mixtures using the dry process

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Márcio Muniz de; Mello, Luiz Guilherme R.; Pereira, Paulo A. A.; Pais, Jorge C.

    2005-01-01

    The modification process of hot mix asphalts in which crumb rubber is initially mixed with the mineral aggregates before the addition of the binder is known as dry process. This process has as main advantages the use of conventional mixing plants and, at least in principle, has no limitation of the incorporated rubber content. The aim of this paper is to study the influence of the incorporated crumb rubber content in the mechanical behavior of dense graded mixes ( grade envelop...

  3. Full-Depth Asphalt Pavements for Parking Lots and Driveways.

    Science.gov (United States)

    Asphalt Inst., College Park, MD.

    The latest information for designing full-depth asphalt pavements for parking lots and driveways is covered in relationship to the continued increase in vehicle registration. It is based on The Asphalt Institute's Thickness Design Manual, Series No. 1 (MS-1), Seventh Edition, which covers all aspects of asphalt pavement thickness design in detail,…

  4. 40 CFR 52.2054 - Control of asphalt paving material.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 4 2010-07-01 2010-07-01 false Control of asphalt paving material. 52... asphalt paving material. (a) Notwithstanding any provisions to the contrary in the Pennsylvania Implementation Plan, the Pennsylvania Department of Transportation shall restrict the annual usage of asphalts...

  5. Effect of crumb rubber on asphaltic binder chemistry and rheology

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Cicero de S.; Tome, Luisa G.A.; Sant' ana, Hosiberto B.; Soares, Jorge B.; Soares, Sandra A. [University Federal of Ceara, Fortaleza, CE (Brazil)

    2008-07-01

    The use of the crumb rubber (CR) from scraps tires to modify asphalt binders (AB) at high temperature can improve significantly the performance grade, but the storage stability can be influenced after the mix of AB and CR or polymer. The major concern of asphalt binder with polymer and CR blends is their lack of stability during prolonged storage at high temperatures. The tendency to phase separation under quiescent conditions appears as an important limitation for the practical use of these blends. After the RTFOT and PAV process, the binder conventional and modified was analyzed in a Fourier Transform Infrared spectrometer (FTIR) for chemical characterization. After aging in RTFOT, the AB presented a larger degradation compared to the CR of RABC and RABC commercial. So, the crumb rubber contributed to the binder stability, acting as an antioxidant in the aging process. The dynamic mechanical properties of CR modify asphalts binder before and after graft has been characterized by use of dynamic shear rheometer (DSR) or advances rheology expanded system (ARES) of Rheometric Scientific. The difference in the viscoelastic parameters between the top and the bottom sections of the tube was measured. It has been found that the added content of CR has great effect on the rheological properties of the AB and its high temperature performance. It also has been confirmed that the RABC sample showed larger storage stability compared to the sample RABC commercial observed with viscoelastic parameters. As a consequence, the use CR and aromatic oil can be considered a suitable alternative for modification of binder in pavement. (author)

  6. Current practices for modification of paving asphalts

    Energy Technology Data Exchange (ETDEWEB)

    Bahia, H.U.; Perdomo, D. [Asphalt Institute, Lexington, KY (United States)

    1996-12-31

    The Superpave binder specification, AASHTO MP1, has introduced new concepts for selecting paving asphalt binders. The specification, in addition to using rheological and failure measurements that are more related to performance, is based on the idea that the criteria to maintain a satisfactory contribution of asphalt binders to the resistance of pavement failures remains the same but have to be satisfied at critical application temperatures. The test procedures require that the material be characterized within certain ranges of strains or stresses to ensure that material and geometric non-linearities are not confounded in the measurements. These new specification concepts have resulted in re-evaluation of asphalt modification by the majority of modified asphalt suppliers. The philosophy of asphalt modification is expected to change, following these new concepts, from a general improvement of quality to more focus on using modifiers based on the most critical need as defined by two factors: (1) The application temperature domain and (2) the type of distress to be remedied. The new specification requirements should result in a more effective use of modifiers as the amount and type of modifier will be directly related to the application environment and the engineering requirements.

  7. Mechanical Response Analysis of Asphalt Pavement Structure

    Directory of Open Access Journals (Sweden)

    Yu Zhenqing

    2015-11-01

    Full Text Available Generally, the Chinese designed life of the high- grade asphalt concrete pavement is required 15 years, however, the designed life of the road in surface is often lower than the designed life, and even premature failure. Especially in heavy traffic conditions, the early damage of some high grade-asphalt pavement in China is serious. According to some investigations, we founded the main reason of the long-life asphalt pavement is to determine the function of each structure layer. According to the stress of pavement structure layer, so as to select the structure layer materials. Based on the viewpoint of mechanics, asphalt pavement damage mode is divided into three categories, such as top-down crack, fatigue cracking and rutting. Therefore, this paper uses ANSYS finite element software as calculation tool, the combination of road vehicle load and the primary influence on asphalt pavement structure mechanics response characteristics were analyzed. In this paper, the method of analysis is control variable: that means under different vehicle axle load, only change surface layer modulus and observe the pavement structure mechanical response trends to compare the effect. By using the same method, the response of the pavement base course parameters to the pavement mechanical structure is analyzed.

  8. Design and Performance of Hot Mix Asphalts with High Percentages of Reclaimed Asphalt: Approach followed in the Paramix Project

    OpenAIRE

    Pérez, F; Rodriguez, M.; De Visscher, J.; Vanelstraete, A.; Bock, L.

    2004-01-01

    The use of reclaimed asphalt pavement (RA) in new asphalt pavements can provide important economical savings, while reducing the negative environmental impact. The European research project PARAMIX aims to improve the techniques for hot mix recycling in plant and cold mix in situ recycling, so as to increase the amount of reclaimed asphalt and develop competitive road pavement rehabilitation techniques. This paper deals with the design of hot mix asphalts for the project. The di...

  9. Analysing polystyrene-modified asphalt and its incidence in a heat-dense asphalt mixture

    Directory of Open Access Journals (Sweden)

    Ana Sofía Figueroa Infante

    2010-04-01

    Full Text Available This article presents some results obtained with an MDC-2 asphalt/polystyrene-modified asphalt mixture as a result of crushing waste glass. The stone, asphalt and polystyrene materials’ were characterised for drawing up the design. The Marshal method was used for obtaining the best asphalt- stone-polystyrene percentages. The Superpave method was used for analysing the asphalt; the mixture’s dynamic behaviour was analysed using a test involving 20ºC and 30ºC trapezoidal fatigue for 90x10-6, 150x10-6 and 220x10-6m deformation. The truck-wheel test was analysed for a 13-ton load, similar to that of the heaviest axle on a Transmilenio (articulated bus. The dynamic module test was analysed for 15ºC, 20ºC and 30ºC and 2.5, 5 and 10 Hz frequencies. Conventional asphalt mixture and modified asphalt results were contrasted, interesting behaviour being observed regarding plastic deformation of the modified mixture in service

  10. Ethanol based foamed asphalt as potential alternative for low emission asphalt technology

    Directory of Open Access Journals (Sweden)

    Mohd Rosli Mohd Hasan

    2016-04-01

    Full Text Available Foamed asphalt typically relies on water as a foaming agent because water becomes gaseous at elevated temperatures, generating numerous tiny bubbles in the asphalt and causing spontaneous foaming. In this study, ethanol was used as a potential alternative to water as a foaming agent. Ethanol is expected to be a physical blowing agent in the same manner as water, except it requires less energy to foam due to its 78 °C boiling point. This study compares the performance of water and ethanol as foaming agents through the measurements of rotational viscosity, the reduction in temperature during foaming, and volatile loss. The ethanol-foamed asphalt binders were prepared at 80 °C and 100 °C, while the water-foamed asphalt binders were prepared at 100 °C and 120 °C. Additionally, the rolling thin film oven (RTFO was used to generate short-term aging of the foamed asphalt binders. A rotational viscometer was used to determine the viscosity of the asphalt binders at 80 °C, 100 °C, 120 °C, 140 °C, and 160 °C. Overall, ethanol can function in the same manner as water but requires less energy to foam. It is proven based on the smaller drop in temperature of the asphalt binder foamed using ethanol compared with that prepared with water. This is due to the lower latent heat capacity of ethanol, which requires less energy to vaporize compared with water. Through the rotational viscometer test, ethanol performs better in lowering the viscosity of asphalt binders, which is essential in allowing production processes at low temperatures, as well as a better workability and aggregate coating. Ethanol can be expelled from the foamed asphalt binders at a higher rate due to its lower boiling point and latent heat.

  11. Performance study of rubber asphalt%橡胶沥青相关性能的试验研究

    Institute of Scientific and Technical Information of China (English)

    郑建伟; 何晓鸣

    2014-01-01

    通过室内试验分析研究了不同橡胶粉掺量对基质沥青的改性效果,分析了橡胶沥青的高温性能,水稳定性,耐久性性能指标。结果表明:在试验范围内,轮胎橡胶粉能显著提高沥青混合料的高温性能,轮胎橡胶粉掺量越高,混合料的高温性能越好;橡胶沥青混合料的残留稳定度要比基质沥青混合料有所提高,体现了橡胶沥青较好的抵抗水损害的能力;橡胶粉改性沥青的耐老化性能也有了一定的提高。%The effect of crumb rubber with different contents on the performance of asphalt rubber was studied through a series of tests .The high temperature performance , water stability , durability performance of rubber as-phalt were analyzed .The results show that rubber powder can remarkably improve the high temperature performance of asphalt mixture .The higher tire rubber powder content , the better the performance of the high temperature of mixture.The residual stability of rubber asphalt mixture was better than the matrix asphalt mixture 's, which embod-ies the rubber asphalt has good resistance for water damage .Rubber powder modified asphalt aging resistance per-formance was improved .

  12. Finite element simulation of asphalt fatigue testing

    DEFF Research Database (Denmark)

    Ullidtz, Per; Kieler, Thomas Lau; Kargo, Anders

    1997-01-01

    The traditional interpretation of fatigue tests on asphalt mixes has been in terms of a logarithmic linear relationship between the constant stress or strain amplitude and the number of load repetitions to cause failure, often defined as a decrease in modulus to half the initial value. To...... accomodate non-constant stress or strain, a mode factor may be introduced or the dissipated energy may be used instead of stress or strain.Cracking of asphalt (or other materials) may be described as a process consisting of three phases. In phase one diffuse microcracking is formed in the material. In the...... damage mechanics.The paper describes how continuum damage mechanics may be used with a finite element program to explain the progressive deterioration of asphalt mixes under laboratory fatigue testing. Both constant stress and constant strain testing are simulated, and compared to the actual results from...

  13. Research on Alkaline Filler Flame-Retarded Asphalt Pavement

    Institute of Scientific and Technical Information of China (English)

    HU Shuguang; ZHANG Houji; WANG Jiaolan

    2006-01-01

    Used as flame retardant of tunnel asphalt pavement, organic bromides produce a large amount of poisons and smoke in construction and flame retardation stage. The alkaline filler was found to replace mineral filler, and the flame-retarded asphalt mixtures were produced. Experimental results show that these asphalt mixtures are smoke restrained; the performances and construction technology of asphalt pavement are not influenced; also the alkaline filler is of low-price. So this kind of flame-retarded asphalt mixtures is suitable for tunnel pavement.

  14. Simulation of rheological behavior of asphalt mixture with lattice model

    Institute of Scientific and Technical Information of China (English)

    杨圣枫; 杨新华; 陈传尧

    2008-01-01

    A three-dimensional(3D) lattice model for predicting the rheological behavior of asphalt mixtures was presented.In this model asphalt mixtures were described as a two-phase composite material consisting of asphalt sand and coarse aggregates distributed randomly.Asphalt sand was regarded as a viscoelastic material and aggregates as an elastic material.The rheological response of asphalt mixture subjected to different constant stresses was simulated.The calibrated overall creep strain shows a good approximation to experimental results.

  15. Rheological evaluation of polymer-modified asphalt binders

    Directory of Open Access Journals (Sweden)

    Mônica Romero Santos Fernandes

    2008-09-01

    Full Text Available Currently, the most used polymer for asphalt binder modification is the thermoplastic elastomer styrene butadiene styrene (SBS and aromatic oil is commonly added to the mixtures to improve their compatibly. This paper proposes the use of oil shale from sedimentary rock as a compatibilizer agent for polymer-modified asphalt binder (PMB. PMBs were produced by mixing a bitumen with a linear SBS copolymer (3.5% (w.w-1 using two oil shale contents (2 and 4% and petroleum aromatic oil to evaluate comparatively the effect of the compatibilizer agent on the SBS PMB properties. The rheological characteristics of the SBS PMBs were analyzed in a dynamic shear rheometer (DSR and the morphology accessed by fluorescence optical microscopy. The viscoelastic behavior of the samples corroborated the results for the classical properties and varied according to the sample morphology and composition. The results indicate that the aromatic and shale oils have similar effects on the microstructure, storage stability and viscoelastic behavior of the PMBs. Thus, shale oil could be successfully used as a compatibilizer agent without loss of properties or could even replace the aromatic oil. Following the Superpave methodology it was observed that the linear- and radial-SBS PMBs and linear-SBS PMB with 2% of shale oil can be used up to 70 °C, and the linear-SBS PMBs with 4% of shale oil or 2% of aromatic oil can be used only up to 64 °C.

  16. Self-monitoring Application of Asphalt Concrete Containing Graphite and Carbon Fibers

    Institute of Scientific and Technical Information of China (English)

    LIU Xiaoming; WU Shaopeng; LI Ning; GAO Bo

    2008-01-01

    The self-monitoring application of asphalt concrete containing graphite and carbon fibers using indirect tensile test and wheel rolling test were introduced. The experiment results indicate that this kind of pitch-based composite is effective for strain/stress self-monitoring. In the indirect tensile test, for a completely conductive asphalt concrete specimen, the piezoresistivity was very weak and slightly positive,which meant the resistivity increase with the increment of tensile strain at all stress/strain amplitudes, with the gage factor as high as 6. The strain self-sensing ability was superior in the case of higher graphite content.However, when the conductive concrete was embedded into common asphalt concrete specimen as a partial structure function, the piezoresistivity was positive at all stress/strain amplitudes and with the gage factor of 13,which was much higher than that of completely conductive specimen. Thus, the strain self-sensing ability was superior when conductive asphalt concrete was taken in as a partial structure function. In the wheel-rolling test,the piezoresistivity was highly positive. At any stress amplitude, the piezoresistivity was strong, with the gage factor as high as 100, which was higher for a stress amplitude of 0.7 MPa than that of 0.5 MPa.

  17. COMPARISON BETWEEN ASPHALTENES (SUBFRACTIONS EXTRACTED FROM TWO DIFFERENT ASPHALTIC RESIDUES: CHEMICAL CHARACTERIZATION AND PHASE BEHAVIOR

    Directory of Open Access Journals (Sweden)

    Silas R. Ferreira

    2016-01-01

    Full Text Available Asphaltenes are blamed for various problems in the petroleum industry, especially formation of solid deposits and stabilization of water-in-oil emulsions. Many studies have been conducted to characterize chemical structures of asphaltenes and assess their phase behavior in crude oil or in model-systems of asphaltenes extracted from oil or asphaltic residues from refineries. However, due to the diversity and complexity of these structures, there is still much to be investigated. In this study, asphaltene (subfractions were extracted from an asphaltic residue (AR02, characterized by NMR, elemental analysis, X-ray fluorescence and MS-TOF, and compared to asphaltene subfractions obtained from another asphaltic residue (AR01 described in a previous article. The (subfractions obtained from the two residues were used to prepare model-systems containing 1 wt% of asphaltenes in toluene and their phase behavior was evaluated by measuring asphaltene precipitation onset using optical microscopy. The results obtained indicated minor differences between the asphaltene fractions obtained from the asphaltic residues of distinct origins, with respect to aromaticity, elemental composition (CHN, presence and content of heteroelements and average molar mass. Regarding stability, minor differences in molecule polarity appear to promote major differences in the phase behavior of each of the asphaltene fractions isolated.

  18. Evaluation of the rheological behavior of asphaltic binder modified with zeolite material

    Energy Technology Data Exchange (ETDEWEB)

    Silveira, E.M. da; Sant' ana, Hosiberto B.; Soares, Sandra A.; Soares, Jorge B. [Federal University of Ceara, Fortaleza, CE (Brazil)

    2008-07-01

    Several new processes have been developed to reduce mixing and compaction temperatures of hot mix asphalt without sacrificing the quality of the resulting pavement. One of these processes utilizes the zeolite, a crystalline hydrated aluminum silicate. A laboratory study was conducted to determine the applicability of zeolite to improve the rheological and chemical behavior of an asphaltic binder. The synthetic asphaltic binder was produced with different zeolite contents (0,1; 0.3; and 0.5% w/w) by wet process. The rheological and chemical behavior was verified by Dynamic Shear Rheometer and Infrared Spectroscopy, respectively. The zeolite's chemical composition and morphology was studied by Dispersive X-ray Spectroscopy (EDX). Additionally, the scanning electron microscope (SEM) was utilized to establish the zeolite elemental composition. The results showed that investigated zeolite was classified as a sodium aluminum silicate and it was able to modify the rheological properties of the neat asphalt binder. The G*/sin{delta} parameter was affected by the zeolite presence, indicating better performance for the binders with zeolite. The results show that synthetic binders can partly replicate the rheological properties of conventional AB. Comparable complex modulus values was obtained. No significant difference was found in viscoelastic response, given by the phase angles as a function of both temperature and frequency. (author)

  19. Asphalts tests using onshore drilling oil wells residues; Ensaios asfalticos utilizando residuos de perfuracao onshore

    Energy Technology Data Exchange (ETDEWEB)

    Lucena, Adriano Elisio de F.L.; Rodrigues, John Kennedy G.; Ferreira, Heber Carlos; Lucena, Leda Christiane de F.L. [Universidade Federal de Campina Grande (UFCG), PB (Brazil); Lucena, Luciana de F.L. [Faculdade de Ciencias Sociais Aplicada (FACISA), Campina Grande, PB (Brazil)

    2008-07-01

    The drilling cuttings are one of the residues produced by the oils industries in large amounts during the drilling of oil wells. An alternative of final disposal of the drilling cutting residue is its utilization in asphalt mixtures. Based on this alternative, it was realized chemical and granulometric analysis and tests (Marshall and indirect tensile strength), on the asphaltic mixture using the residue from the oil drilling wells (well: 1-POTI-4-RN, located at Governador DIX-Sept Rosado - RN - Brazil). The achieved results to Marshall test indicated that for the analyzed mixture, the ideal content of residue that can be incorporated to the asphaltic composition and attend at the DNIT-ES 31 (2006) is 5%. To the indirect tensile strength test, the results showed a strength value higher than the minimum limit requested by the DNIT (0,65 MPa). The achieved results indicated the possibility of the utilization of the drilling cuttings in asphaltic pavements as fine aggregate, obeying the percentage limits, as an alternative to the final disposal. (author)

  20. Comparison of laboratory test performance between asphalt-rubber hot mix and dense graded asphalt concrete

    OpenAIRE

    Sousa, Jorge B.; Pais, Jorge C.; Stubstad, Richard N.

    2000-01-01

    "Reflective cracking in pavements : research in practice" contains the Proceedings of the 4th International RILEM Conference on Reflective Cracking in Pavements (Proceedings PRO11). Asphalt-Rubber Hot-Mix (ARHM) has shown a higher resistance to flexural and reflective fatigue cracking, and also to permanent deformation, than conventional Dense Graded Asphalt Concrete (DGAC). Experience has demonstrated that with ARHM, a significant reduction in overlay thickness is possible, especially in...

  1. Performance Evaluation of Stone Mastic Asphalt and Hot Mix Asphalt Mixtures Containing Recycled Concrete Aggregate

    OpenAIRE

    Mohammad Saeed Pourtahmasb; Mohamed Rehan Karim

    2014-01-01

    Environmental and economic considerations have encouraged civil engineers to find ways to reuse recycled materials in new constructions. The current paper presents an experimental research on the possibility of utilizing recycled concrete aggregates (RCA) in stone mastic asphalt (SMA) and hot mix asphalt (HMA) mixtures. Three categories of RCA in various percentages were mixed with virgin granite aggregates to produce SMA and HMA specimens. The obtained results indicated that, regardless of t...

  2. Advanced methodology for optimization of mixture design of asphalt concrete containing reclaimed asphalt pavement material

    OpenAIRE

    Bressi, Sara

    2016-01-01

    Despite the massive use of Reclaimed Asphalt Pavement (RAP) in Hot Mix Asphalt (HMA) production, the chemo-physical phenomena that characterise the fabrication of these mixtures have not yet been completely explored. The detection and understanding of these mechanisms as well as the study of the heterogeneity that characterizes high RAP mix production are fundamental to improving the approach to recycling, because they represent the source of the mixture characteristics and performance. This...

  3. Microstructural Analysis and Rheological Modeling of Asphalt Mixtures Containing Recycled Asphalt Materials

    Directory of Open Access Journals (Sweden)

    Augusto Cannone Falchetto

    2014-09-01

    Full Text Available The use of recycled materials in pavement construction has seen, over the years, a significant increase closely associated with substantial economic and environmental benefits. During the past decades, many transportation agencies have evaluated the effect of adding Reclaimed Asphalt Pavement (RAP, and, more recently, Recycled Asphalt Shingles (RAS on the performance of asphalt pavement, while limits were proposed on the amount of recycled materials which can be used. In this paper, the effect of adding RAP and RAS on the microstructural and low temperature properties of asphalt mixtures is investigated using digital image processing (DIP and modeling of rheological data obtained with the Bending Beam Rheometer (BBR. Detailed information on the internal microstructure of asphalt mixtures is acquired based on digital images of small beam specimens and numerical estimations of spatial correlation functions. It is found that RAP increases the autocorrelation length (ACL of the spatial distribution of aggregates, asphalt mastic and air voids phases, while an opposite trend is observed when RAS is included. Analogical and semi empirical models are used to back-calculate binder creep stiffness from mixture experimental data. Differences between back-calculated results and experimental data suggest limited or partial blending between new and aged binder.

  4. Evaluation of Warm Mix Asphalt Additives for Use in Modified Asphalt Mixtures

    Science.gov (United States)

    Chamoun, Zahi

    The objective of this research effort is to evaluate the use of warm-mix additives with polymer modified and terminal blend tire rubber asphalt mixtures from Nevada and California. The research completed over two stages: first stage evaluated two different WMA technologies; Sasobit and Advera, and second stage evaluated one additional WMA technology; Evotherm. The experimental program covered the evaluation of resistance of the mixtures to moisture damage, the performance characteristics of the mixtures, and mechanistic analysis of mixtures in simulated pavements. In the both stages, the mixture resistance to moisture damage was evaluated using the indirect tensile test and the dynamic modulus at multiple freeze-thaw cycles, and the resistance of the various asphalt mixtures to permanent deformation using the Asphalt Mixture Performance Tester (AMPT). Resistance of the untreated mixes to fatigue cracking using the flexural beam fatigue was only completed for the first stage. One source of aggregates was sampled in, two different batches, three warm mix asphalt technologies (Advera, Sasobit and Evotherm) and three asphalt binder types (neat, polymer-modified, and terminal blend tire rubber modified asphalt binders) typically used in Nevada and California were evaluated in this study. This thesis presents the resistance of the first stage mixtures to permanent deformation and fatigue cracking using two warm-mix additives; Advera and Sasobit, and the resistance to moisture damage and permanent deformation of the second stage mixtures with only one warm-mix additive; Evotherm.

  5. Content

    DEFF Research Database (Denmark)

    Keiding, Tina Bering

    Aim, content and methods are fundamental categories of both theoretical and practical general didactics. A quick glance in recent pedagogical literature on higher education, however, reveals a strong preoccupation with methods, i.e. how teaching should be organized socially (Biggs & Tang, 2007; R...... strategy is theoretically based on systems theory as formulated by Niklas Luhmann (Luhmann, 1995; 2002) and on own work, where. Luhmann’s general ideas and concepts of the educational system are transposed into a didactical framework (Keiding, 2005,2007,2008).......Aim, content and methods are fundamental categories of both theoretical and practical general didactics. A quick glance in recent pedagogical literature on higher education, however, reveals a strong preoccupation with methods, i.e. how teaching should be organized socially (Biggs & Tang, 2007......, is subordinating content to methods as seen in modern didactics, hereby transforming content to a medium for achievement of learning-to-learn skills rather than something valuable in its own right. At the level of general didactics quite few attempts have been made to formulate criteria and...

  6. Asphalt modification with used lubricating oil

    Energy Technology Data Exchange (ETDEWEB)

    Villanueva, A.; Ho, S.; Zanzotto, L. [Calgary Univ., AB (Canada). Schulich School of Engineering, Bituminous Materials Research Laboratory

    2008-02-15

    A method of recycling waste lubricating oil from vehicles was presented. Various asphalt materials were modified with different amounts of lubricating oil and analyzed using standard Superpave tests. Dynamic shear rheometer (DSR) tests were then conducted to in order to obtain high temperature samples. Bending beam rheometer (BBR) and direct tension tests (DTT) were used to obtain low temperature sample profiles. Potential applications for the materials were reviewed. Environmental impacts and costs associated with using the materials were also presented. The study demonstrated that waste lubricating oil can be used as a softening agent in modified asphalt binders using a low temperature grade technique. It was concluded that the low cost of waste lubricating oil in Alberta makes it a potential resource for asphalt modification. The oil modified samples lowered the high-temperature grade and did not improve the overall quality of the asphalt. Further testing is needed to examine the quality and consistency of lubricating oils. 19 refs., 7 tabs., 12 figs.

  7. Determining and Modeling Asphalt Concrete Response (ACRe)

    NARCIS (Netherlands)

    Erkens, S.M.J.G.; Poot, M.R.

    2000-01-01

    In road engineering research and design the principles of material mechanics have not yet become a standard tool. In this contribution a project aimed at applying these principles to asphalt concrete is presented. Attention is paid to the differences between the standard test procedures and those ba

  8. Finite element simulation of asphalt fatigue testing

    DEFF Research Database (Denmark)

    Ullidtz, Per; Kieler, Thomas Lau; Kargo, Anders

    damage mechanics.The paper describes how continuum damage mechanics may be used with a finite element program to explain the progressive deterioration of asphalt mixes under laboratory fatigue testing. Both constant stress and constant strain testing are simulated, and compared to the actual results from...

  9. Microbial Life in a Liquid Asphalt Desert

    Science.gov (United States)

    Schulze-Makuch, Dirk; Haque, Shirin; de Sousa Antonio, Marina Resendes; Ali, Denzil; Hosein, Riad; Song, Young C.; Yang, Jinshu; Zaikova, Elena; Beckles, Denise M.; Guinan, Edward; Lehto, Harry J.; Hallam, Steven J.

    2011-04-01

    Pitch Lake in Trinidad and Tobago is a natural asphalt reservoir nourished by pitch seepage, a form of petroleum that consists of mostly asphaltines, from the surrounding oil-rich region. During upward seepage, pitch mixes with mud and gases under high pressure, and the lighter portion evaporates or is volatilized, which produces a liquid asphalt residue characterized by low water activity, recalcitrant carbon substrates, and noxious chemical compounds. An active microbial community of archaea and bacteria, many of them novel strains (particularly from the new Tar ARC groups), totaling a biomass of up to 107 cells per gram, was found to inhabit the liquid hydrocarbon matrix of Pitch Lake. Geochemical and molecular taxonomic approaches revealed diverse, novel, and deeply branching microbial lineages with the potential to mediate anaerobic hydrocarbon degradation processes in different parts of the asphalt column. In addition, we found markers for archaeal methane metabolism and specific gene sequences affiliated with facultative and obligate anaerobic sulfur- and nitrite-oxidizing bacteria. The microbial diversity at Pitch Lake was found to be unique when compared to microbial communities analyzed at other hydrocarbon-rich environments, which included Rancho Le Brea, a natural asphalt environment in California, USA, and an oil well and a mud volcano in Trinidad and Tobago, among other sites. These results open a window into the microbial ecology and biogeochemistry of recalcitrant hydrocarbon matrices and establish the site as a terrestrial analogue for modeling the biotic potential of hydrocarbon lakes such as those found on Saturn's largest moon Titan.

  10. Modeling of asphalt-rubber rotational viscosity by statistical analysis and neural networks

    Directory of Open Access Journals (Sweden)

    Luciano Pivoto Specht

    2007-03-01

    Full Text Available It is of a great importance to know binders' viscosity in order to perform handling, mixing, application processes and asphalt mixes compaction in highway surfacing. This paper presents the results of viscosity measurement in asphalt-rubber binders prepared in laboratory. The binders were prepared varying the rubber content, rubber particle size, duration and temperature of mixture, all following a statistical design plan. The statistical analysis and artificial neural networks were used to create mathematical models for prediction of the binders viscosity. The comparison between experimental data and simulated results with the generated models showed best performance of the neural networks analysis in contrast to the statistic models. The results indicated that the rubber content and duration of mixture have major influence on the observed viscosity for the considered interval of parameters variation.

  11. Evaluation and Study the Effect of Additives and Other Factors on Tensile Strength of Asphalt Paving Mixtures

    Directory of Open Access Journals (Sweden)

    Hanaa Khaleel A. Al-Baiti

    2012-03-01

    Full Text Available The resistance of asphaltic concrete to cracking is dependent upon its tensile strength and flexibility characteristics. Also the low tensile strength has recognized as a major contributor to other performance problems. The fatigue life of mixtures decreases exponentially with decreasing of tensile strength. This trend is justified by the loss in stiffness and thereby initiating cracks and stripping. The main objective of this research is intended to study the effect of different variables related with the used materials and the external conditions on the tensile strength and predict a model of indirect tensile strength in asphalt concrete paving materials under the local prevailing conditions and investigate the effect of percent of additives of (Polyestrene resins and Hydrated Lime to enhance the resistance ability of asphalt concrete mixture against distresses. The main affected factors; soaking, asphalt content, compaction, aggregate maximum size and temperature, influence on the indirect tensile strength and presented through a statistics analysis model for tensile strength in asphalt mixture

  12. Use of Reclaimed Asphalt Pavement in Conjunction with Ground Improvement: A Case History

    OpenAIRE

    Foye, Kevin C.

    2011-01-01

    The use of Reclaimed Asphalt Pavement (RAP) in lieu of virgin crushed stone aggregate is becoming a widely accepted practice for a number of construction applications, particularly pavement base courses. A number of laboratory RAP studies have considered the mechanical properties of RAP bases in order to support pavement designs incorporating RAP. These studies have revealed a number of interesting relationships between RAP moisture content, compaction, and stiffness. This paper discusses the...

  13. Effects of diurnal temperature dynamics on curing of cold-emulsion reclaimed asphalt pavements

    OpenAIRE

    Kiplagat Chelelgo

    2010-01-01

    Strength development in Cold-Emulsion Reclaimed Asphalt Pavements is gradual and largely dependent on the rate at which curing proceeds. Its early life strength is therefore low and presents a major challenge in material specification for mechanistic pavement design. The solution has been to subject a sample of the mixture to be used in the pavement to accelerated laboratory curing to the attainment of Equilibrium Moisture Content (EMC) condition. Fatigue and Stiffness parameters of the mix a...

  14. Properties of asphalt-rubber binders related to characteristics of the incorporated crumb rubber

    OpenAIRE

    Dantas Neto, Silvrano A.; Farias, Márcio Muniz de; Pais, Jorge C.; Pereira, Paulo A. A.; Santos, Luís Picado

    2003-01-01

    The behavior of asphalt binders modified with recycled crumb rubber depends on several factors, such as: rubber contents and type, temperature and time employed during the digestion process. This paper shows the results of a series of tests performed on asphaltrubber produced via the wet process. The tests included standard penetration, softening point, Brookfield viscosity and resilience. The results show that the limiting variable in the digestion process is the Brookfield vi...

  15. Effects of Asphalt Mix Design Properties on Pavement Performance: A Mechanistic Approach

    Directory of Open Access Journals (Sweden)

    Ahmad M. Abu Abdo

    2016-01-01

    Full Text Available The main objective of this study was to investigate the effects of hot mix asphalt material properties on the performance of flexible pavements via mechanistic approach. 3D Move Analysis software was utilized to determine rutting and cracking distresses in an asphalt concrete (AC layer. Fourteen different Superpave mixes were evaluated by utilizing results of the Dynamic Modulus (|E⁎| Test and the Dynamic Shear Modulus (|G⁎| Test. Results showed that with the increase of binder content, the tendency of rutting in AC layer increased. However, with the increase of binder content, the cracking of AC layer lessened. Furthermore, when different binder grades were evaluated, results showed that with the increase of the upper binder grade number, rutting decreased, and with the increase of the lower binder grade number, rutting increased. Furthermore, analysis showed that with the increase of the lower binder grade number, higher percent of bottom up cracks would result. As a result of the analysis, binder grade should not be solely considered for cracking in AC layer; binder content and aggregate structure play a big role. Finally, results illustrated that the mechanistic approach is a better tool to determine the performance of asphalt pavement than commonly used methods.

  16. Viscoelastic Analysis of Asphalt Mixture Based on Creep Test

    Directory of Open Access Journals (Sweden)

    Lihua Zhao

    2013-01-01

    Full Text Available Two kinds of mineral fibers were added to AC-16C asphalt mixture. Trabecular bending creep experiments of asphalt mixtures were carried out at -10 and 20°C. The influence of mineral fibers on the low temperature viscoelasticity of asphalt mixtures were analyzed systemically. Furthermore, by using Origin, Burgers viscoelastic model was used to investigate the parameter regression for the creep test results at the different temperatures. The results show that the addition of mineral fibers can effectively improve the bending creep rate of asphalt mixtures, indicates the increase of crack resistance of asphalt mixtures. Good agreement between experimental data and Burgers model was found. The parameters of Burgers model at different temperatures can also provide data support for the viscoelastic design of asphalt pavements.

  17. Research on Surfactant Warm Mix Asphalt Construction Technology

    Science.gov (United States)

    Li, Guoliang; Sun, Jingxin; Guo, Xiufeng

    Discharging temperature of hot asphalt mixture is about 150°C-185°C, volatilization of asphalt fume harms people's health and fuel cost is high. Jinan Urban Construction Group applies PTL/01 asphalt warm mix agent to produce warm mix asphalt to construction of urban roads' asphalt bituminous pavement. After comparing it with performance of traditional hot asphalt mixture, mixing temperature may be reduced by 30°C-60°C, emission of poisonous gas is reduced, energy conservation and environmental protection are satisfied, construction quality reaches requirements of construction specifications and economic, social and environmental benefits are significant. Thus, it can be used for reference for green construction of urban roads.

  18. CONTENTS

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    The Development and Evolution of the Idea of the Mandate of Heaven in the Zhou Dynasty The changes in the idea of Mandate of Heaven during the Shang and Zhou dynasties are of great significance in the course of the development of traditional Chinese culture. The quickening and awakening of the humanistic spirit was not the entire content of the Zhou idea of Mandate of Heaven. In the process of annihilating the Shang dynasty and setting up their state, the Zhou propagated the idea of the Mandate of Heaven out of practical needs. Their idea of the Mandate of Heaven was not very different from that of the Shang. From the Western Zhou on, the Zhou idea of Mandate of Heaven by no means developed in a linear way along a rational track. The intermingling of rationality and irrationality and of awakening and non-awakening remained the overall state of the Zhou intellectual superstructure after their "spiritual awakening".

  19. Evaluation of Hydrated Lime Filler in Asphalt Mixtures

    OpenAIRE

    Mohammed Abbas Hasan Al-Jumaily

    2008-01-01

    Mineral filler is one of important materials and affecting on properties and quality of asphalt mixtures .There are different types of mineral filler depended on cost and quality , the matter encourages us to achieve this study to evaluate hydrated lime filler effects on properties of asphalt mixes related with strength and durability. Conventional asphaltic concrete mixtures with Portland cement and soft sandstone fillers and mixtures modified with hydrated lime were evaluated for their fund...

  20. Deformation Parameters and Fatigue of the Recycled Asphalt Mixtures

    OpenAIRE

    Šrámek Juraj

    2015-01-01

    The deformational properties of asphalt mixtures measured by dynamic methods and fatigue allow a design the road to suit the expected traffic load. Quality of mixtures is also expressed by the resistance to permanent deformation. Complex modulus of stiffness and fatigue can reliably characterize the proposed mixture of asphalt pavement. The complex modulus (E*) measurement of asphalt mixtures are carried out in laboratory of Department of Construction Management at University of Žilina by two...

  1. Review and Recommendation of Cold Asphalt Emulsion Mixtures Caems Design

    OpenAIRE

    I Nyoman Arya Thanaya

    2007-01-01

    Note from the Editor Cold Asphalt Emulsion Mixture (CAEM) is a mixture of aggregates and asphalt emulsion that is mixed at room temperature. It is relatively simple to produce, but the design procedure provided by the Asphalt Institute and the Ministry of Public Work of Indonesia pose some problems in its practical application. This Technical Note discusses limitations of the current design procedures and presents a simpler and more practicable design procedure

  2. Viscoelastic Analysis of Asphalt Mixture Based on Creep Test

    OpenAIRE

    Lihua Zhao; Jingyun Chen; Shengwu Wang

    2013-01-01

    Two kinds of mineral fibers were added to AC-16C asphalt mixture. Trabecular bending creep experiments of asphalt mixtures were carried out at -10 and 20°C. The influence of mineral fibers on the low temperature viscoelasticity of asphalt mixtures were analyzed systemically. Furthermore, by using Origin, Burgers viscoelastic model was used to investigate the parameter regression for the creep test results at the different temperatures. The results show that the addition of mineral fibers can ...

  3. Mix design of bituminous materials including reclaimed asphalt pavement

    OpenAIRE

    Dubois, Vincent; De La Roche, Chantal

    2008-01-01

    Reclaimed asphalt, obtained by milling of asphalt road layers can be re-used at once or stored. In the case of storage, an heterogeneity issue may occur when several types of materials, with different origins are mixed. At the scale of a storage zone or a stock pile, composition and properties of the reclaimed asphalts will be different, including variations of the final material properties, constraints for the stock manager, and the necessary adaptation of the manufacturing process. The recl...

  4. The Development of Moisture Sensitivity Test for Compacted Asphalt

    OpenAIRE

    M.K. Shamshuddin; M.E. Abdullah; Rhasbudin Shah, S.M.

    2011-01-01

    Moisture damage is one of the major issues in asphalt distress. It is due to the adhesive and cohesive failure of asphalt mixture and it will shorten pavement life. Moisture-sensitive mixtures need to be identified during the course of the mixture design process which fulfills the specified minimum standard. The laboratory testing procedures currently available for compacted Hot Mix Asphalt (HMA) to test the moisture sensitivity were primarily developed to determine the degree ...

  5. Review and Recommendation of Cold Asphalt Emulsion Mixtures Caems Design

    Directory of Open Access Journals (Sweden)

    I Nyoman Arya Thanaya

    2007-01-01

    Full Text Available Note from the Editor Cold Asphalt Emulsion Mixture (CAEM is a mixture of aggregates and asphalt emulsion that is mixed at room temperature. It is relatively simple to produce, but the design procedure provided by the Asphalt Institute and the Ministry of Public Work of Indonesia pose some problems in its practical application. This Technical Note discusses limitations of the current design procedures and presents a simpler and more practicable design procedure

  6. Determination of Rheological Properties of Bio Mastic Asphalt

    OpenAIRE

    R. Muniandy; H. Jafariahangari; Yunus, R.; S. Hassim

    2008-01-01

    Due to the high oil prices the price of asphalt binder has increased tremendously. This scenario has warranted demand for higher viscosity cheaper asphalt for pavement construction. A study was conducted to take advantage of the Empty Fruit Bunch (EFB) of Date and Oil Palm trees (which are considered as waste) to produce cellulose fiber to be used as additives in the asphalt binder. If these EFB's could be beneficially utilized in any application, it would reduce the load on the nation's land...

  7. Porous Flame-retarded Asphalt Pavement for Highway Tunnel

    Institute of Scientific and Technical Information of China (English)

    HU Shuguang; HUANG Shaolong; Ding Qingjun

    2008-01-01

    A new way to improve the tunnel fire protection by using flame-retarded porous asphalt pavement containing ATH powders was introduced. Based on the miniature burning test designed and conducted, the burning time and temperature of porous asphalt (PA) and flame-retarded porous asphalt (FRPA) were studied comparing with cement concrete pavement, dense-graded HMA and S MA. Results of burning test and pavement performance test indicate that FRPA is appropriate and suitable as the pavement material of highway tunnel.

  8. Evaluation of asphalt-rubber membrane field performance

    Science.gov (United States)

    Shuler, S.; Gallaway, B. M.; Epps, J. A.

    1982-05-01

    This report presents a record of asphalt-rubber membrane field performance in Texas. An evaluation of performance is presented for forty-five separate projects in thirteen state highway districts. Approximately 850 lane miles of highways are represented by materials constructed as stress absorbing membranes (asphalt-rubber seal coats beneath asphalt concrete overlay). All projects reviewed were constructed between June, 1976 and September, 1981.

  9. Comparison between asphalt rubber and conventional mixtures in overlay design

    OpenAIRE

    Fontes, Liseane P. T. L.; Trichês, Glicério; Pereira, Paulo A. A.; Pais, Jorge C.

    2008-01-01

    Asphalt modified with crumb rubber has been used to produce asphalt rubber mixtures for pavement overlays subjected to heavy loads and high temperatures. Under severe conditions, these mixtures are capable of resisting permanent deformations, having an extended fatigue life and resisting crack propagation in comparison to conventional ones. A laboratory research was conducted to determine the performance properties of overlays with asphalt rubber mixtures produced through wet processes using ...

  10. Performance Evaluation of Semiplastic Recycled Cold Asphalt Using Noncement Binders

    OpenAIRE

    Lee, Byung Jae; Bang, Jin Wook; Kim, Jeong Su; Jang, Young Il

    2015-01-01

    The optimal mixing conditions for semiplastic recycled cold asphalt, which recycled waste asphalt and used noncement binders (NCB), were assessed through verification of the performance. The NCB of 6% desulfurization gypsum mixing was found to have the most outstanding properties. For the Marshall stability, 4% (NCB) filler mixing brought about a 1.92-time strength increase effect compared to OPC (2%) and was improved when using modified asphalt and SBR. The flow test results showed that alth...

  11. Extending the Life of Asphalt Longitudinal Paving Joints

    OpenAIRE

    Hedges, Rex; Brownridge, Jim

    2014-01-01

    Is premature asphalt joint failure bringing your PASER number down? Participants will learn how applying asphalt preservative seals directly to the asphalt longitudinal paving joint can restore plasticity and flexibility and how application of in-depth sealing methods will protect against harmful UV rays, prevent oxidation, and waterproof against chloride intrusion. Rehabilitation methods to repair poorly performing and failed paving joints will also be covered.

  12. Increasing the rate of recycled asphalt: an experimental study

    Directory of Open Access Journals (Sweden)

    Marjan TUŠAR

    2014-09-01

    Full Text Available Asphalt is material that can be recycled. In particular reclaimed asphalt (RA contains aged binder, which limits the reuse of RA. In this study the rate of recycled asphalt was increased by adding a rejuvenator containing paraffin. The authors investigated the effect of the rejuvenator in laboratory and in plant prepared samples of asphalt mixture. In laboratory samples with different percentage of RA (0%, 10%, 30%, 50% and rejuvenator were prepared. In asphalt plant only asphalt mixture with highest amount of RA and rejuvenator and control mixture without RA were prepared. On samples were conducted different tests, e.g. determining softening point, Fraass breaking point, penetration, indirect tensile strength. Results on extracted bitumen showed increase in softening point and decrease in Fraass breaking point with increasing percentage of RA and rejuvenator, meaning that service temperature of binders increased. Asphalt samples prepared in asphalt plant were laid on test field. Asphalt with RA and rejuvenator was built in at lower temperature (round 100 °C. Mixtures with RA and rejuvenator have better low temperature properties confirmed with Thermal Stress Restrained Specimen Test (TSRST method, but are less resistant to compaction and less sensitive to water than control mixture. For comparison of long term behaviour wheel tracking test was performed on mixtures built in test field. A week after paving, the control mixture showed better properties, but one year later the results were opposite, asphalt containing RA and rejuvenator was more resistant to rutting. From the results of this experimental study the following was concluded: the amount of RA can be increased by using rejuvenator and the quality of such asphalt mixture is in most cases equal or even better than asphalt mixture made of virgin materials. By using RA we preserve nature, reduce usage of virgin raw materials, but it is cost effective only if recycling degree is high

  13. Thermal Properties of Asphalt Mixtures Modified with Conductive Fillers

    OpenAIRE

    Byong Chol Bai; Dae-Wook Park; Hai Viet Vo; Samer Dessouky; Ji Sun Im

    2015-01-01

    This paper investigates the thermal properties of asphalt mixtures modified with conductive fillers used for snow melting and solar harvesting pavements. Two different mixing processes were adopted to mold asphalt mixtures, dry- and wet-mixing, and two conductive fillers were used in this study, graphite and carbon black. The thermal conductivity was compared to investigate the effects of asphalt mixture preparing methods, the quantity, and the distribution of conductive filler on thermal pro...

  14. Bone Glue Modified Asphalt: A Step towards Energy Conservation and Environment Friendly Modified Asphalts

    Science.gov (United States)

    Rizvi, Hashim Raza; Gallo, August A.

    2014-01-01

    Asphalt has been modified for the past several decades using various additives, including synthetic polymers. Polymer modification improves structural and engineering characteristics of the binder, which is a result of improvement in rheological characteristics of binder as well as its adhesion capability with the aggregate. Such enhancement inevitably enhances the performance characteristics of hot mix asphalts (HMA) such as fatigue life, resistance to rutting, and thermal cracking. Even though polymer-modified HMA is popular in North America and European countries, its use is still limited in developing countries of Southeast Asia due to high costs associated with its manufacturing, processing, and energy consumption. In this study, a new kind of asphalt modifier derived from animal wastes, such as bones, hides, and flesh commonly known as Bone Glue, is studied. This biomaterial which is a by-product of food and cattle industries is cheap, conveniently available, and produced locally in developing countries. The results of the research study showed that the bone glue can easily be mixed with asphalt without significantly altering the asphalt binder's viscosity and mixing and compaction temperatures of HMA. Additionally, improvements in complex shear modulus for a range of temperatures were also determined and it was found that complex shear modulus was improved by bone glue modification.

  15. Modification of Asphalt by the Use of Crumb Rubber

    Directory of Open Access Journals (Sweden)

    Shah Room

    2014-01-01

    Full Text Available Health aspects enforced to ponder a study on asphalt which incorporate rubber crumbs to increase strength and flexibility of asphalt. Disposal of waste tires is a menace and it’s a serious problem globally because it is not easily biodegradable as these tires consume large spaces, open burning cause serious problems. By the use of rubber tires, this scrap is utilized efficiently and reduces the cost of asphalt to produce economical system. The asphalt is absorbed by the rubber particles which swells at high temperature allowing greater concentration of liquid asphalt. The partial replacement of crumb rubber in asphalt is 5%, 10%, 15%, and 20% (D05, D10, D15, and D20. The analysis of incorporated asphalt was done in hot mix asphalt. The generated results showed that the value for resilient modulus and creep stiffness is more as compared to the conventional asphalt and in the accumulated strain the values are much lesser which is positive approach.

  16. Hanford Permanent Isolation Barrier Program: Asphalt technology development

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Romine, R.A.

    1994-11-01

    An important component of the Hanford Permanent Isolation Barrier is the use of a two-layer composite asphalt system, which provides backup water diversion capabilities if the primary capillary barrier fails to meet infiltration goals. Because of asphalt`s potential to perform to specification over the 1000-year design life criterion, a composite asphalt barrier (HMAC/fluid-applied polymer-modified asphalt) is being considered as an alternative to the bentonite clay/high density poly(ethylene) barriers for the low-permeability component of the Hanford Permanent Isolation Barrier. The feasibility of using asphalt as a long-term barrier is currently being studied. Information that must be known is the ability of asphalt to retain desirable physical properties over a period of 1000 years. This paper presents the approach for performing accelerated aging tests and evaluating the performance of samples under accelerated conditions. The results of these tests will be compared with asphalt artifact analogs and the results of modeling the degradation of the selected asphalt composite to make life-cycle predictions.

  17. Creep Characteristics of Crumb Rubber Modified Asphalt Binder

    Institute of Scientific and Technical Information of China (English)

    WANG Lan; CHANG Chunqing; XING Yongming

    2011-01-01

    Crumb rubber modified asphalt containing 20 percent crumb rubber particles of 30mesh has been examined by Scanning Electron Microscope (SEM) to observe the microcosmic appearance and the characteristic distribution of crumb rubber particles in asphalt. The SEM pictures reveal that the crumb rubber particles distribute evenly in the asphalt and they are compatible well with asphalt. The shear creep test of crumb rubber modified asphalt was carried out at - 10 ℃ and 40 ℃ by Dynamic Shear Rheology (DSR). The shearing deformation at different temperature and creep stiffness modulus curve at loading stage of crumb rubber modified asphalt have been measured. The stiffness modulus of crumb rubber modified asphalt is much temperature sensitive and it decays much quick at the early stage of loading than normal asphalt. The rate of decay of stiffness modulus is slow at the subsequent stage and stiffness modulus approaches to a stable value at the final stage at a higher temperature. In addition, Burgers model is suitable to describe and simulate experimental results of viscoelastic properties of the crumb rubber modified asphalt.

  18. Safety evaluation of asphalt products for final disposal

    International Nuclear Information System (INIS)

    Under the present situation, the wastes concentrated according to the radioactivity level, the properties and the environmental conditions are usually solidified in view of limiting the escape of the radioactive substances to the environment as small as possible by containment. The materials used for the solidification are cement, asphalt, plastics, ceramics and so on, and the selection is made by taking the kinds and radioactivity level of wastes, final disposing method, economy and handling into consideration. Asphalt is more suitable than cement to the wastes coming from PWR power plants, which contain boric acid for controlling nuclear reaction, and the effect of reducing the volume of wastes is high. It is economical when a certain scale is reached, accordingly recently, the use of asphalt for the solidification of wastes is going to increase. For the solidification of low level wastes, straight-run asphalt is suitable, and for high level wastes, heat-resistant blown asphalt is suitable. Asphalt-solidified bodies can contain 40-60 wt.% of wastes without any problem. The present situation of asphalt solidification in foreign countries, the physical properties required for the disposal of asphalt-solidified bodies, and the leaching, combustibility, radiation resistance and form stability of asphalt-solidified bodies are described. (Kako, I.)

  19. Field testing of asphalt-emulsion radon-barrier system

    International Nuclear Information System (INIS)

    Three years of laboratory and field testing have demonstrated that asphalt emulsion seals are effective radon diffusion barriers. Both laboratory and field tests in 1979, 1980 and 1981 have shown that an asphalt emulsion seal can reduce radon fluxes by greater than 99.9%. The effective diffusion coefficient for the various asphalt emulsion admix seals averages about 10-6 cm2/s. The 1981 joint field test is a culmination of all the technology developed to date for asphalt emulsion radon barrier systems. Preliminary results of this field test and the results of the 1980 field test are presented. 18 figures, 6 tables

  20. Performance Evaluation of Semiplastic Recycled Cold Asphalt Using Noncement Binders

    Directory of Open Access Journals (Sweden)

    Byung Jae Lee

    2015-01-01

    Full Text Available The optimal mixing conditions for semiplastic recycled cold asphalt, which recycled waste asphalt and used noncement binders (NCB, were assessed through verification of the performance. The NCB of 6% desulfurization gypsum mixing was found to have the most outstanding properties. For the Marshall stability, 4% (NCB filler mixing brought about a 1.92-time strength increase effect compared to OPC (2% and was improved when using modified asphalt and SBR. The flow test results showed that although an increase dosage of filler and SBR decreased the flow value of the semiplastic recycled cold asphalt, an increase dosage of asphalt emulsion improved the flow value. The indirect tensile strength and liquid immersion residual stability for the condition with greatest Marshall stability were most outstanding with 0.95 MPa and 83.6%, respectively. Evaluation of the recycled cold asphalt abrasion durability revealed that for the case of mixing more than 4% NCB the mass loss rate was lower than 20%. The abrasion durability was found to improve when using modified emulsified asphalt and SBR substitution. From the test results, it was found that the optimal mixing proportion of semiplastic recycled cold asphalt satisfied mechanical properties and durability is NCB with 4%, emulsified asphalt with 3%, and SBR substitution with 20%.

  1. Experimental Study on Influencing Factors of Rubber Asphalt Performance%橡胶沥青性能影响因素的试验研究

    Institute of Scientific and Technical Information of China (English)

    许云

    2011-01-01

    In order to properly control rubber asphalt technology, rubber asphalt is prepared separately by different rubber powder, fineness, mixing temperature and substrate asphalt to carry out test on penetration degree, softening point, elastic restitution and SHRP in order to separately test high-temperature performance, low-temperature performance and aging resistance of rubber asphalt and analyze the influence of each factor on rubber asphalt performance. The result shows that 20-mesh rubber powder with 16 %-18 % content is more appropriate for preparation of rubber asphalt.%为了正确控制橡胶沥青工艺,采用不同胶粉种类、胶粉细度、拌和温度、基质沥青类型等制备橡胶沥青,进行针入度、软化点、弹性恢复以及SHRP等试验,分别测试橡胶沥青的高温性能、低温性能、抗老化性能等,研究各因素对橡胶沥青性能的影响,得出20目橡胶粉掺量以16%~18%较为合适的结果.

  2. Contents

    Directory of Open Access Journals (Sweden)

    Editor IJRED

    2012-11-01

    Full Text Available International Journal of Renewable Energy Development www.ijred.com Volume 1             Number 3            October 2012                ISSN 2252- 4940   CONTENTS OF ARTICLES page Design and Economic Analysis of a Photovoltaic System: A Case Study 65-73 C.O.C. Oko , E.O. Diemuodeke, N.F. Omunakwe, and E. Nnamdi     Development of Formaldehyde Adsorption using Modified Activated Carbon – A Review 75-80 W.D.P Rengga , M. Sudibandriyo and M. Nasikin     Process Optimization for Ethyl Ester Production in Fixed Bed Reactor Using Calcium Oxide Impregnated Palm Shell Activated Carbon (CaO/PSAC 81-86 A. Buasri , B. Ksapabutr, M. Panapoy and N. Chaiyut     Wind Resource Assessment in Abadan Airport in Iran 87-97 Mojtaba Nedaei       The Energy Processing by Power Electronics and its Impact on Power Quality 99-105 J. E. Rocha and B. W. D. C. Sanchez       First Aspect of Conventional Power System Assessment for High Wind Power Plants Penetration 107-113 A. Merzic , M. Music, and M. Rascic   Experimental Study on the Production of Karanja Oil Methyl Ester and Its Effect on Diesel Engine 115-122 N. Shrivastava,  , S.N. Varma and M. Pandey  

  3. Extending the Lifespan of Porous Asphalt Concrete

    OpenAIRE

    Zhang, Y.

    2015-01-01

    Porous Asphalt (PA) concrete is widely used as a surfacing layer on highways in the Netherlands. The service life of PA wearing courses is limited because of the fact that it is vulnerable to raveling. The possibilities of applying preventive maintenance to PA wearing courses by means of spraying rejuvenation products on the pavement surfaces are being investigated with high interest in the Netherlands. A material which has the ability to penetrate into the bituminous binder and soften (rejuv...

  4. Classification of recycled asphalt 'RA' material

    OpenAIRE

    Wendling, Louisette; DE LA ROCHE SAINT ANDRE, Chantal; Gaudefroy, Vincent; Marsac, Paul; TEBALDI, Gabriele; DAVE, Eshan; HUGENER, Martin; BOCCI, Maurizio; LOIZOS, Andreas; JENKINS, Kim; MARRADI, Alessandro; Grilli, Andrea; Graziani, Andrea; PASETTO, Marco; MURAYA, Patrick

    2012-01-01

    Use of recycled asphalt pavements (RA) in pavement rehabilitation processes is continuously growing as recycling techniques, such as cold recycling (CR), are being utilized in increasing magnitude. The focus of this paper is on developing a state of the art and state of the practice summary of processes used for classification of RA. A variety of topics were explored through an exhaustive literature search, these include RAP production methods, definition of RA materials, stockpiling practice...

  5. Optimizing Use Of Marshall Asphalt Mix Design

    OpenAIRE

    Lindly, Jay

    1997-01-01

    Rutting has been a problem in Qatar's highway pavements since it began designing asphalt mixtures with the Marshall Method in the early 1990's. This paper describes specifications and rules-of-thumb which have been generated in the United States which may provide insight to Qatar's rutting problem and suggests modifications to mix design and construction procedures. The paper describes appropriate bitumen and aggregate specifications and discusses field procedures to implement mix design va...

  6. Injuries in short track asphalt racing.

    Science.gov (United States)

    Busby, J D

    1978-10-01

    Stock car racing is a popular activity. Although spectators are seldom injured, drivers at short asphalt tracks often sustain minor injuries. The neck and the knee are the most commonly injured areas. Rigid safety requirements are essential and help to prevent serious injuries. Severe injuries occur on an average of once a year, but no fatalities have been recorded at one short track that has been studied for a six-year period. PMID:707264

  7. Dynamic Modulus Test Analysis of Sulfur Modified Asphalt Mixture%硫磺改性沥青混合料的动态模量试验分析

    Institute of Scientific and Technical Information of China (English)

    侯睿; 郭忠印

    2013-01-01

    UTM system was used to test asphalt mixture's dynamic modulus with different sulfur contents (by mass).The influences of temperature,loading frequency and sulfur content on the viscoelastic properties of asphalt mixtures were analyzed.The results show that the temperature and loading frequency have the same influence on dynamic modulus of both sulfur modified asphalt mixture and conventional asphalt mixture.The effect of sulfur contents on viscoelastic properties of asphalt mixtures is different.A small quantity of sulfur will increase asphalt mixture's viscosity and temperature sensitivity,but a large quantity of sulfur will increase asphalt mixture's elasticity and reduce temperature sensitivity.%采用UTM系统对不同硫磺掺量(质量比)的沥青混合料进行动态模量试验,分析了温度、加载频率和硫磺掺量对沥青混合料黏弹特性的影响.结果表明:温度和加载频率对硫磺改性沥青混合料和普通沥青混合料动态模量的影响规律基本相同;不同硫磺掺量对沥青混合料黏弹性能的影响有所不同,硫磺掺量较小时,沥青混合料的黏性增加,温度敏感性增大;硫磺掺量较大时,沥青混合料的弹性增加,温度敏感性降低.

  8. 基质沥青的种类对橡胶沥青的影响研究%THE STUDY OF THE IMPACT THAT THE CATEGORY OF BASE ASPHALT BRING ABOUT TO RUBBERIZED ASPHALT

    Institute of Scientific and Technical Information of China (English)

    何东坡; 李海文

    2011-01-01

    There are plenty of factors that affect the performance of rubberized asphalt, however, this paper mainly consider the impact that the category of base asphalt bring about to waste crumb rubber modified asphalt This paper respectively adopts Da Qing and Panjin AH-90# base asphalt, which are commonly used in Heilongjiang province, with the same preparation technique-the powder content is 18% ; the power mesh is 80 mesh; the mixing temperature is 180 ℃; the mixing time is 60 min. Pene-tration , ductility, softening point, elastic recovery and rotation viscosity had been chosen as the technol-ogy and performance indexes. Test results indicate that the category of base asphalt has minor influence on rubberized asphalt%影响废胶粉改性沥青性能的因素很多,本文主要考虑基质沥青的种类对其性能的影响.分别采用黑龙江省常用的大庆和盘锦AH - 90#基质沥青,采用相同的制备条件:胶粉掺量为18%,胶粉目数为80目,搅拌时间为60min,搅拌温度为180℃,检测废胶粉改性沥青的针入度,延度软化点,弹性恢复,旋转粘度.试验结果表明,基质沥青的种类对废胶粉改性沥青性能的影响不大.

  9. Active carbon production from modified asphalt

    International Nuclear Information System (INIS)

    A granular activated carbons (GACs) have been prepared from some local raw materials such as Qiayarah asphalt (QA) after some modification treatments of this asphalt by various ratios of its original constituents (asphaltenes and maltens) at 180 degree C. Thermal carbonization method by sulfur and steam physical activation have been used for AC preparation. The carbons thus prepared were characterized in the term of iodine, methylene blue (MB), P-nitro phenol (PNP) and CCl4 adsorption. The BET surface area of the prepared ACs has been estimated via a calibration curve between iodine numbers and surface area determined from N2 adsorption isotherm from previous studies, also, the surface area of the prepared ACs were determined through another methods such as retention method by ethylene glycol mono ethyl ether (EGME), adsorption from vapor phase using acetone vapor and adsorption from solution method using PNP and MB as solutes. The results referred to the success of modification method for preparing ACs of good micro porosity as compared with the AC from the untreated asphalt as well as the commercial sample. (author)

  10. Method of interrupting asphalt solidifying operation

    International Nuclear Information System (INIS)

    Purpose: To shorten the time required for interrupting operation, by specifying methods of supplying and interrupting liquid wastes, water and asphalts. Method: Electrical power supply for a heat medium heater is disconnected simultaneously with the start for the stopping operation. The temperature for the heat medium is detected by a heat medium thermometer, the flow rate of a waste liquid supply pump is reduced by way of a rotation controller for the liquid waste supply pump and the amount of liquid wastes supplied is gradually decreased along with the reduction in the temperature for the heat medium. Then, when the temperature for the heat medium lowered to about 190 - 2100C, supply of the liquid wastes is interrupted and cleaning water is supplied to a liquid wastes supply tank while closing the liquid wastes supply tank main valve and opening a cleaning water valve to thereby clean the radioactive substances. Then, after stopping the supply of the cleaning water, asphalt is continued to be supplied for several minutes, the radioactive substances deposited in an evaporator and an agitation blade are sufficiently washed out. Then, after stopping the asphalt tank, operations for the driving device and the heat medium pump are stopped. This enables cooling for the heat medium in a short time using no exclusive heat medium cooler, as well as clean the radioactive substances. (Horiuchi, T.)

  11. Performance Characteristic of Cold Recycled Mixture with Asphalt Emulsion and Chemical Additives

    Directory of Open Access Journals (Sweden)

    Shaowen Du

    2015-01-01

    Full Text Available Three types of chemical additives were used to modify asphalt emulsion recycled mixture. These chemical additives include composite Portland cement (CPC, hydrated lime (HL, and a combination of hydrated lime and ground-granulated blast-furnace slag (GGBF. The influence of different additives on the recycled mixture performance was investigated by volumetric and strength tests, moisture susceptibility test, rutting resistance test, and low temperature bending test. To better understand its performance characteristic, the microstructure images of the recycled mixture were observed by environmental scanning electron microscope (ESEM. Test results demonstrate that the performance improvement of the emulsion recycled mixture depends on the types and content of chemical additives. Several recommendations are presented for the selection of chemical materials. Based on ESEM image analysis, the interface bonding mechanism is proposed to explain the performance characteristic of the recycled mixture with asphalt emulsion and cementitious materials.

  12. Chemical characterization of oil-based asphalt release agents and their emissions

    Energy Technology Data Exchange (ETDEWEB)

    Bing Tang; Ulf Isacsson [Royal Institute of Technology, Stockholm (Sweden). Division of Highway Engineering, Department of Civil and Architectural Engineering

    2006-06-15

    Four commercial asphalt release agents were chemically characterized using different analytical methods. Functional groups and molecular weight distributions were determined by fourier transform infrared spectroscopy-attenuated total reflectance (FTIR-ATR), gel permeation chromatography (GPC) and mass spectrometry (MS). General compositions of the agents were obtained as petroleum hydrocarbons, fatty acid methyl esters (FAMEs), fatty acids and glycerides using gas chromatography-mass spectrometry (GC-MS) and MS probe inlet method. The contents of health related analytes, such as aromatic hydrocarbons and polycyclic aromatic hydrocarbons (PAHs), were determined. Asphalt release agents emission was investigated using thermogravimetric analysis (TGA) and headspace solid-phase microextraction (HS-SPME). The emission proneness as well as emission level of aromatic hydrocarbons from these agents were compared. The results obtained were used for ranking the agents with regard to health hazards. 19 refs., 7 figs., 6 tabs.

  13. Dynamic linear viscoelastic properties and extensional failure of asphalt binders

    Science.gov (United States)

    Ruan, Yonghong

    Billions of dollars are spent annually in USA to maintain old pavements that are badly cracked. In order to reduce this expenditure, it is desirable to have criteria for selecting asphalts with superior cracking resistance that will provide pavements with longer durability. Literature reports indicate that the ductility of binders recovered from asphalt pavements correlates with cracking failure. However, ductility measurement is a time and material consuming process, and subject to reproducibility difficulties, as are all failure tests. In addition, ductility measurement does not belong to the currently used Superpave(TM) specification. Correlations between ductility and dynamic viscoelastic properties (measured with the dynamic shear rheometer, DSR), which are much easier and faster to perform and may be included into the Superpave(TM) system, are studied for both straight and modified binders. Ductility correlates quite well with G'/(eta '/G') for conventional asphalt binders aged at different conditions, especially when ductility is below 10 cm. However, for modified asphalts, there is no universal correlation between ductility and G'/(eta'/G'), even in the low ductility region. As far as the asphalt binder in pavement is concerned, the loss due to oxidative aging of its ductility is an important reason for pavement cracking. Polymer modification modifies the rheological and oxidative hardening properties of asphalt binders. The effect of polymeric modifiers on various properties of asphalt binders was investigated. Modifiers studied were diblock poly (styrene-b-butadiene) rubber (SBR), triblock poly (styrene-b-butadiene-b-styrene) (SBS), and tire rubber. Polymer modified binders have a lower hardening and oxidation rate than their corresponding base asphalts. In addition, modified binders have lower hardening susceptibility compared with their base materials and in some cases the results can be dramatic. Polymer modification improves asphalt binders' shear

  14. Asphalt features and gas accumulation mechanism of Sinian reservoirs in the Tongwan Palaeo-uplift, Sichuan Basin

    Directory of Open Access Journals (Sweden)

    Wei Li

    2015-10-01

    Full Text Available Breakthroughs have been made in natural gas exploration in Sinian reservoirs in the Tongwan Palaeo-uplift, Sichuan Basin, recently. However, there are disputes with regard to the genetic mechanisms of natural gas reservoirs. The development law of asphalts in the Sinian reservoirs may play an extremely important role in the study of the relationships between palaeo oil and gas reservoirs. Accordingly, researches were conducted on the features and development patterns of asphalts in the Sinian reservoirs in this area. The following research results were obtained. (1 Asphalts in the Sinian reservoirs were developed after the important hydrothermal event in the Sichuan Basin, namely the well-known Emei Taphrogeny in the mid-late Permian Period. (2 Distribution of asphalts is related to palaeo oil reservoirs under the control of palaeo-structures of Indosinian-Yanshanian Period, when the palaeo-structures contained high content of asphalts in the high positions of the palaeo-uplift. (3 Large-scale oil and gas accumulations in the Sinian reservoirs occurred in the Indosinian-Yanshanian Period to generate the Leshan-Ziyang and Gaoshiti-Moxi-Guang'an palaeo oil reservoirs. Cracking of crude oil in the major parts of these palaeo oil reservoirs controlled the development of the present natural gas reservoirs. (4 The development of asphalts in the Sinian reservoirs indicates that hydrocarbons in the Dengying Formation originated from Cambrian source rocks and natural gas accumulated in the Sinian reservoirs are products of late-stage cracking of the Sinian reservoirs. (5 The Sinian palaeo-structures of Indosinian-Yanshanian Period in the Sichuan Basin are favorable regions for the development of the Sinian reservoirs, where discoveries and exploration practices will play an important role in the era of Sinian natural gas development in China.

  15. Effect of waste plastic bottles on the stiffness and fatigue properties of modified asphalt mixes

    International Nuclear Information System (INIS)

    Highlights: • PET reduced the mix stiffness at both temperatures of 5 and 25 °C. • PET improved the fatigue behavior at both testing temperatures. • At more than 210 microstrain, adding temperature resulted in higher fatigue life. • SBS modified mixes showed better fatigue behavior than PET modified ones. • Overall PET had comparable effects to SBS on the stiffness and fatigue behavior. - Abstract: Nowadays, the use of recycled waste materials as modifier additives in asphalt mixes could have several economic and environmental benefits. The main purpose of this research was to investigate the effect of waste plastic bottles (Polyethylene Terephthalate (PET)) on the stiffness and specially fatigue properties of asphalt mixes at two different temperatures of 5 and 20 °C. Likewise, the effect of PET was compared to styrene butadiene styrene (SBS) which is a conventional polymer additive which has been vastly used to modify asphalt mixes. Different PET contents (2–10% by weight of bitumen) were added directly to mixture as the method of dry process. Then the resilient modulus and fatigue tests were performed on cylindrical specimens with indirect tensile loading procedure. Overall, the mix stiffness reduced by increasing the PET content. Although stiffness of asphalt mix initially increased by adding lower amount of PET. Based on the results of resilient modulus test, the stiffness of PET modified mix was acceptable and warranted the proper deformation characteristics of these mixes at heavy loading conditions. At both temperatures, PET improved the fatigue behavior of studied mixes. PET modified mixes revealed comparable stiffness and fatigue behavior to SBS at 20 °C. However, at 5 °C the fatigue life of SBS modified mixes was to some extent higher than that of PET modified ones especially at higher strain levels of 200 microstrain

  16. Rubber-like Quasi-thermosetting Polyetheramine-cured Epoxy Asphalt Composites Capable of Being Opened to Traffic Immediately

    Science.gov (United States)

    Kang, Yang; Wu, Qiang; Jin, Rui; Yu, Pengfei; Cheng, Jixiang

    2016-01-01

    This paper reports the facile preparation, mechanical performance and linear viscoelasticity of polyetheramine-cured rubber-like epoxy asphalt composites (EACs) with different asphalt contents. Compared with previous EACs prepared via complex chemical reactions and time-consuming high-temperature curing, the EACs reported here were obtained by using a compatible, bi-functional polyetheramine and a simple physical co-blend process, which make the EACs feasibly scalable for production at a lower cost. The EACs were cured for 1 h at 160 °C and 3 d at 60 °C therefore, these composites can be opened to traffic immediately. The EACs have a much greater temperature stability than common thermoplastic polymer-modified asphalt composites from -30 °C to 120 °C, but their complex shear moduli at higher temperatures slightly decrease instead of remaining constant when temperatures are greater than 80 °C, especially for the higher asphalt content composites; that is, these composites are quasi-thermosetting. Wicket plots illustrate that the EACs reported here are thermorheological simple materials, and the master curves are constructed and well-fitted by generalized logistic sigmoidal model functions. This research provides a facile, low-cost method for the preparation of polyetheramine-cured EACs that can be opened to traffic immediately, and the concept of quasi-thermosetting may facilitate the development of cheaper EACs for advanced applications.

  17. 7 CFR 2902.36 - Concrete and asphalt release fluids.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 15 2010-01-01 2010-01-01 false Concrete and asphalt release fluids. 2902.36 Section... PROCUREMENT Designated Items § 2902.36 Concrete and asphalt release fluids. (a) Definition. Products that are designed to provide a lubricating barrier between the composite surface materials (e.g., concrete...

  18. Characterization of Failure and Permanent Deformation Behaviour of Asphalt Concrete

    NARCIS (Netherlands)

    Wang, J.G.

    2015-01-01

    Asphalt concrete is a viscoelastic material consisting of aggregates, filler and bitumen. The response of asphalt concrete is highly dependent on temperature, loading rate and confining pressure. Permanent deformation is one of the most important distresses developing during the flexible pavement se

  19. Laboratory and Field Asphalt Fatigue Performance, Matching Theory with Practice

    NARCIS (Netherlands)

    Pramesti, F.P.

    2015-01-01

    This thesis investigates the relationship between predicted and observed fatigue life of asphalt. This study also investigates the positive effects of modifying bitumen with Retona, a bitumen modifier produced in Indonesia from natural asphalt rock sources, on pavement performance in terms of increa

  20. Basics of a Good Road: Asphalt and Aggregates

    OpenAIRE

    Huber, Gerry

    2014-01-01

    This Asphalt 101 presentation will focus on binder (liquid asphalt) production, covering the following specific topics: how it is produced, PG grades and modification (certified binder supplier program), product transportation, and storage at plant. Additionally, aggregate production will be covered, including sizing, gradations, types (slag, limestone, gravel), and Indiana sources and quality (CAPP).

  1. Hot asphalt burns: a review of injuries and management options.

    Science.gov (United States)

    Bosse, George M; Wadia, Shernaz A; Padmanabhan, Pradeep

    2014-07-01

    Hot asphalt burns to human tissue can increase the likelihood of infection and potential conversion of partial thickness to full-thickness injuries. Successful intervention for hot asphalt burns requires immediate and effective cooling of the asphalt on the tissue followed by subsequent gradual removal of the cooled asphalt. A review of the literature reveals that multiple substances have been used to remove asphalt, including topical antibiotics, petroleum jelly, a commercial product known as De-Solv-It (ORANGE-SOL, Chandler, AZ), sunflower oil, baby oil, liquid paraffin, butter, mayonnaise, and moist-exposed burn ointment (MEBO). Although many of these products may be effective in the removal of asphalt, they may not be readily available in an emergency department setting. Topical antibiotics are readily available, are more commonly described in the medical literature, and would be expected to be effective in the removal of asphalt. We developed guidelines for on scene (first-aid) management and the initial care of such patients upon presentation to a health care facility. These guidelines emphasize the principles of early cooling, gradual removal of adherent asphalt using topical antibiotics, and avoidance of the use of topical agents, which are likely to result in tissue toxicity. PMID:24630605

  2. Effects of conductive fillers on temperature distribution of asphalt pavements

    International Nuclear Information System (INIS)

    The sun provides a cheap and abundant source of clean and renewable energy. Solar cells have been used to capture this energy and generate electricity. A more useful form of the solar cell would be asphalt pavements, which get heated up by solar radiation. Graphite powders are utilized as thermal conductive fillers to make an asphalt collector conductive so as to improve the efficiency of the asphalt collector. Accounting for the important application conditions and evaluating the effects of the heat conductive materials and the solar energy absorbability of the conductive asphalt collector, a finite element model has been developed to predict temperature distributions in the conductive asphalt solar collector. In this study, an experimental validation exercise was conducted using the measured data taken from full-depth asphalt slabs. Validation results showed that the model can satisfactorily predict the temperature distributions in asphalt concrete slabs. The optimal depth is 25-50 mm for placing pipes that serve as the heat exchanger. Meanwhile, the effect of the surroundings on the solar energy potential of the asphalt collector was noticeable.

  3. Improving the quality of asphalt coating with carbon nanomodifiers

    Science.gov (United States)

    Larisa, Urkhanova; Nikolay, Shestakov; Aleksandr, Semenov; Natalya, Smirnyagina; Irina, Semenova

    2015-07-01

    This article deals with the possibility of modifying the binder by adding carbon nanomodifier to bitumen to improve the quality of asphalt. Addition of 0.05%-0.5% of nanomodifier significantly changes the properties of bitumen. Asphalt with this astringent has increased strength, heat resistance and shear resistance.

  4. Hanford Permanent Isolation Barrier Program: Asphalt technology development

    International Nuclear Information System (INIS)

    An important component of the Hanford Permanent Isolation Barrier is the use of a two-layer composite asphalt system, which provides backup water diversion capabilities if the primary capillary barrier fails to meet infiltration goals. Because of asphalt's potential to perform to specification over the 1000-year design life criterion, a composite asphalt barrier (HMAC/fluid-applied polymer-modified asphalt) is being considered as an alternative to the bentonite clay/high density poly(ethylene) barriers for the low-permeability component of the Hanford Permanent Isolation Barrier. The feasibility of using asphalt as a long-term barrier is currently being studied. Information that must be known is the ability of asphalt to retain desirable physical properties over a period of 1000 years. This paper presents the approach for performing accelerated aging tests and evaluating the performance of samples under accelerated conditions. The results of these tests will be compared with asphalt artifact analogs and the results of modeling the degradation of the selected asphalt composite to make life-cycle predictions

  5. 40 CFR Table 1 of Subpart Aaaaaaa... - Emission Limits for Asphalt Processing (Refining) Operations

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Emission Limits for Asphalt Processing... Area Sources: Asphalt Processing and Asphalt Roofing Manufacturing Other Requirements and Information... of Part 63—Emission Limits for Asphalt Processing (Refining) Operations For * * * You must meet...

  6. 40 CFR 443.30 - Applicability; description of the asphalt roofing subcategory.

    Science.gov (United States)

    2010-07-01

    ... asphalt roofing subcategory. 443.30 Section 443.30 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Roofing Subcategory § 443.30 Applicability; description of the asphalt roofing subcategory. The provisions of this subpart are applicable to...

  7. 40 CFR 443.20 - Applicability; description of the asphalt concrete subcategory.

    Science.gov (United States)

    2010-07-01

    ... asphalt concrete subcategory. 443.20 Section 443.20 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Concrete Subcategory § 443.20 Applicability; description of the asphalt concrete subcategory. The provisions of this subpart are applicable to...

  8. 40 CFR 443.40 - Applicability; description of the linoleum and printed asphalt felt subcategory.

    Science.gov (United States)

    2010-07-01

    ... linoleum and printed asphalt felt subcategory. 443.40 Section 443.40 Protection of Environment... PAVING AND ROOFING MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Linoleum and Printed Asphalt Felt Subcategory § 443.40 Applicability; description of the linoleum and printed asphalt felt subcategory....

  9. 40 CFR 443.10 - Applicability; description of the asphalt emulsion subcategory.

    Science.gov (United States)

    2010-07-01

    ... asphalt emulsion subcategory. 443.10 Section 443.10 Protection of Environment ENVIRONMENTAL PROTECTION... MATERIALS (TARS AND ASPHALT) POINT SOURCE CATEGORY Asphalt Emulsion Subcategory § 443.10 Applicability; description of the asphalt emulsion subcategory. The provisions of this subpart are applicable to...

  10. Monitoring asphalt pavement damages using remote sensing techniques

    Science.gov (United States)

    Mettas, Christodoulos; Themistocleous, Kyriacos; Neocleous, Kyriacos; Christofe, Andreas; Pilakoutas, Kypros; Hadjimitsis, Diofantos

    2015-06-01

    One of the main issues in the maintenance plans of road agencies or governmental organizations is the early detection of damaged asphalt pavements. The development of a smart and non-destructive systematic technique for monitoring damaged asphalt pavements is considered a main priority to fill this gap. During the 1970's, remote sensing was used to map road surface distress, while during the last decade, remote sensing became more advanced, thereby assisting in the evolution of the identification and mapping of roads. Various techniques were used in order to explore condition, age, weaknesses and imperfections of asphalted pavements. These methods were fairly successful in the classification of asphalted surfaces and in the detection of some of their characteristics. This paper explores the state of the art of using remote sensing techniques for monitoring damaged pavements and some typical spectral profiles of various asphalt pavements in Cyprus area acquired using the SVC1024 field spectroradiometer.

  11. Mechanical Properties of Asphalt Pavement Structure in Highway Tunnel

    Institute of Scientific and Technical Information of China (English)

    SHI Chun-xiang; GUO Zhong-yin

    2008-01-01

    A linear full 3D finite element method (FEM) was performed in order to present the key design parameters of highway tunnel asphalt pavement under double-wheel load on rectangular loaded area considering horizontal contact stress induced by the acceleration/deceleration of vehicles. The key design parameters are the maximum horizontal tensile stresses at the surface of the asphalt layer, the maximum horizontal tensile stresses at the bottom of the asphalt layer and the maximum vertical shear stresses at the surface of the as- phalt layer were calculated. The influencing factors such as double-wheel weight; asphalt layer thickness; base course stiffness modulus and thickness; and the contact conditions among the structure layers on these key design parameters were also examined separately to propose construction procedures of highway tunnel asphalt pavement.

  12. Effect of ageing on fatigue properties of asphalt

    Institute of Scientific and Technical Information of China (English)

    王佶; 庞凌; 吴少鹏; 刘全涛; 陈筝

    2008-01-01

    The fatigue properties of asphalts were investigated after various laboratory simulation ageing tests and outdoor natural exposure ultraviolet radiation ageing,by dynamic shear rheometer(DSR) time sweep fatigue test in constant strain model and a new type of specimen which was introduced to avoid the problem of adhesion failure between rotor and asphalt binder.The results show that outdoor natural exposure ageing(NEA) causes the decrease of retained fatigue life distinctly,and photodegradation caused by outdoor NEA of 1 250 μm thin films asphalt for three months,is found to be severer than pressure ageing vessel(PAV) with respects to retained fatigue life.The effect of photodegradation increases as the time of outdoor NEA increases.DSR time sweep fatigue test in constant strain indicates that the aged styrene-butadiene-styrene(SBS) modified asphalt still displays better fatigue properties than the corresponding base asphalt after ageing.

  13. Preparation of Flame Retardant Modified with Titanate for Asphalt Binder

    Directory of Open Access Journals (Sweden)

    Bo Li

    2014-01-01

    Full Text Available Improving the compatibility between flame retardant and asphalt is a difficult task due to the complex nature of the materials. This study explores a low dosage compound flame retardant and seeks to improve the compatibility between flame retardants and asphalt. An orthogonal experiment was designed taking magnesium hydroxide, ammonium polyphosphate, and melamine as factors. The oil absorption and activation index were tested to determine the effect of titanate on the flame retardant additive. The pavement performance test was conducted to evaluate the effect of the flame retardant additive. Oxygen index test was conducted to confirm the effect of flame retardant on flame ability of asphalt binder. The results of this study showed that the new composite flame retardant is more effective in improving the compatibility between flame retardant and asphalt and reducing the limiting oxygen index of asphalt binder tested in this study.

  14. Laboratory Mix Design of Asphalt Mixture Containing Reclaimed Material

    Directory of Open Access Journals (Sweden)

    Davide Lo Presti

    2014-01-01

    Full Text Available This paper presents a study on the production of asphalt test specimens in the laboratory containing reclaimed asphalt. The mixtures considered were stone mastic asphalt concrete mixtures containing up to 30% of reclaimed asphalt. Specimens were compacted to the reference density obtained from the Marshall mix design. Gyration compaction method was used for preparing specimens for the experimental programme, while coring and cutting methods and X-ray computed tomography (CT were used to investigate the change in properties within the specimens and to validate the selected methodology. The study concluded that gyratory compaction is suitable to produce homogeneous test specimens also for mixtures containing high amount of reclaimed asphalt. Nevertheless, preliminary trials for each material are mandatory, as well as final coring and trimming of the specimens due to side effects.

  15. THE FATIGUE DURABILITY OF THE MODIFIED ASPHALT CONCRETE UNDER THE EFFECT OF INTENSIVE TRAFFIC LOADS

    Directory of Open Access Journals (Sweden)

    Yuri KALGIN

    2016-06-01

    Full Text Available The problem of prediction of the service life of asphalt concrete surface constructed with modified asphalt concrete application onto a traffic lane is examined. Asphalt concrete behaviour in road surface under the traffic loads was analysed. There were shown The results of experiments and their mathematical analysis of the assessment of standard and modified cold asphalt concrete fatigue life on road surface were shown. The service life of an asphalt concrete surface covered with standard and modified cold asphalt concrete is examined. The prediction has been received with an account of stress relaxation processes in asphalt concrete pavement and unevenness of traffic load application.

  16. Surface Modification of Fire-retardant Asphalt with Silane Coupling Agent

    Institute of Scientific and Technical Information of China (English)

    CHEN Huiqiang; TANG Boming

    2012-01-01

    The theory and approach of the surface modified of asphalt fire-retardant with silane coupling agent were introduced,The optimum silane dosage was determined,and the structure and properties of the asphalt fire-retardant before and after the surface modification were characterized by infrared spectrum and thermo gravimetric analysis.The dispersion effect of asphalt fire-retardant was studied.The influence of the surface modification on the hydrophilicity and lipophilicity of the asphalt fire-retardant was analyzed.The experimental results showed that there were physical and chemical interactions between the silane coupling agent and the asphalt fire-retardant,which reduced the surface polarity of the asphalt fire retardant.The optimum silane coupling agent dosage was 0.95% of the asphalt fire retardant.The surface modification improved the thermal stability,dispersibility and lipophilicity of the asphalt fire retardant,which enhanced the compatibility between asphalt fire retardant and asphalt.

  17. A study on the rheological properties of recycled rubber-modified asphalt mixtures.

    Science.gov (United States)

    Karacasu, Murat; Okur, Volkan; Er, Arzu

    2015-01-01

    Using waste rubber in asphalt mixes has become a common practice in road construction. This paper presents the results of a study on the rheological characteristics of rubber-modified asphalt (RMA) concrete under static and dynamic loading conditions. A number of static and dynamic creep tests were conducted on RMA mix specimens with different rubber sizes and contents, and a series of resonant column tests were conducted to evaluate the shear modulus and damping values. To simulate the stress-strain response of traffic-induced loading, the measurements were taken for different confining pressures and strain levels. The results of the study indicated that rubber modification increases stiffness and damping ratio, making it a very attractive material for use in road construction. However the grain size of the rubber is very important. Although RMA may cost up to 100% more than regular asphalt, the advantages it brings, such as an increased service life of the road and proper waste utilization contributing to a more sustainable infrastructure, may justify the added cost. PMID:25695096

  18. A Study on the Rheological Properties of Recycled Rubber-Modified Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Murat Karacasu

    2015-01-01

    Full Text Available Using waste rubber in asphalt mixes has become a common practice in road construction. This paper presents the results of a study on the rheological characteristics of rubber-modified asphalt (RMA concrete under static and dynamic loading conditions. A number of static and dynamic creep tests were conducted on RMA mix specimens with different rubber sizes and contents, and a series of resonant column tests were conducted to evaluate the shear modulus and damping values. To simulate the stress-strain response of traffic-induced loading, the measurements were taken for different confining pressures and strain levels. The results of the study indicated that rubber modification increases stiffness and damping ratio, making it a very attractive material for use in road construction. However the grain size of the rubber is very important. Although RMA may cost up to 100% more than regular asphalt, the advantages it brings, such as an increased service life of the road and proper waste utilization contributing to a more sustainable infrastructure, may justify the added cost.

  19. Stiffness modulus of Polyethylene Terephthalate modified asphalt mixture: A statistical analysis of the laboratory testing results

    International Nuclear Information System (INIS)

    Highlights: • Effect of PET modification on stiffness property of asphalt mixture was examined. • Different temperatures and loading amounts were designated. • Statistical analysis was used to find interactions between selected variables. • A good agreement between experimental results and predicted values was obtained. • Optimal amount of PET was calculated to achieve the highest mixture performance. - Abstract: Stiffness of asphalt mixture is a fundamental design parameter of flexible pavement. According to literature, stiffness value is very susceptible to environmental and loading conditions. In this paper, effects of applied stress and temperature on the stiffness modulus of unmodified and Polyethylene Terephthalate (PET) modified asphalt mixtures were evaluated using Response Surface Methodology (RSM). A quadratic model was successfully fitted to the experimental data. Based on the results achieved in this study, the temperature variation had the highest impact on the mixture’s stiffness. Besides, PET content and amount of stress showed to have almost the same effect on the stiffness of mixtures. The optimal amount of PET was found to be 0.41% by weight of aggregate particles to reach the highest stiffness value

  20. Performance-based asphalt mixture design methodology

    Science.gov (United States)

    Ali, Al-Hosain Mansour

    Today, several State D.O.T.s are being investigating the use of tire rubber with local conventional materials. Several of the ongoing investigations identified potential benefits from the use of these materials, including improvements in material properties and performance. One of the major problems is being associated with the transferability of asphalt rubber technology without appropriately considering the effects of the variety of conventional materials on mixture behavior and performance. Typically, the design of these mixtures is being adapted to the physical properties of the conventional materials by using the empirical Marshall mixture design and without considering fundamental mixture behavior and performance. Use of design criteria related to the most common modes of failure for asphalt mixtures, such as rutting, fatigue cracking, and low temperature thermal cracking have to be developed and used for identifying the "best mixture," in term of performance, for the specific local materials and loading conditions. The main objective of this study was the development of a mixture design methodology that considers mixture behavior and performance. In order to achieve this objective a laboratory investigation able to evaluate mixture properties that can be related to mixture performance, (in terms of rutting, low temperature cracking, moisture damage and fatigue), and simulating the actual field loading conditions that the material is being exposed to, was conducted. The results proved that the inclusion of rubber into asphalt mixtures improved physical characteristics such as elasticity, flexibility, rebound, aging properties, increased fatigue resistance, and reduced rutting potential. The possibility of coupling the traditional Marshall mix design method with parameters related to mixture behavior and performance was investigated. Also, the SHRP SUPERPAVE mix design methodology was reviewed and considered in this study for the development of an integrated

  1. THE FATIGUE DURABILITY OF THE MODIFIED ASPHALT CONCRETE UNDER THE EFFECT OF INTENSIVE TRAFFIC LOADS

    OpenAIRE

    Yuri KALGIN; Alexander STROKIN

    2016-01-01

    The problem of prediction of the service life of asphalt concrete surface constructed with modified asphalt concrete application onto a traffic lane is examined. Asphalt concrete behaviour in road surface under the traffic loads was analysed. There were shown The results of experiments and their mathematical analysis of the assessment of standard and modified cold asphalt concrete fatigue life on road surface were shown. The service life of an asphalt concrete surface covered with standard an...

  2. Some Properties of Emulsified Asphalt Paving Mixture at Iraqi Environmental Conditions

    OpenAIRE

    Shakir.A.Al-Mishhadani; Hasan.H.Al-Baid

    2014-01-01

    Cold emulsified asphalt mixture is generally a mix made of emulsified asphalt withaggregate. Emulsified asphalt is manufactured from base asphalt, emulsifier agent and waterwith approximate percentage of 40% to 75% asphalt, 0.1% to 2.5% emulsifier and 25% to60% water plus some minor components. This study aims to use the cold emulsified asphaltmixtures for road construction and maintenance in Iraq as an alternative to the hot asphaltmixtures, due to its economical, practical and environmental...

  3. The first engineered self-healing asphalt road: How is it performing?

    OpenAIRE

    Liu, Q.; Schlangen, H.E.J.G.; Van Bochove, G.

    2013-01-01

    Porous asphalt shows excellent performance in both noise reduction and water drainage. Although porous asphalt has these great qualities, its service life is much shorter (sometimes only half) compared to dense graded asphalt roads. Ravelling, which is the loss of aggregate particles from the surface layer, is the main damage mechanism of porous asphalt surface wearing courses. In this research, an induction healing approach (namely, activating the healing process of asphalt concrete through ...

  4. Decision of National and Provincial Highway Asphalt Pavement Structure Based on Value Engineering

    OpenAIRE

    Yingwei Ren; Jingsong Shan

    2014-01-01

    It is important that decision of asphalt pavement structure requires overall considerations of the performance and financial investment. To have asphalt pavement structure fulfilling good reliability, the asphalt pavement structure decision was researched based on value engineering theory. According to the national and provincial highway investigation data in Shandong Province during the last decade, the asphalt pavement performance attenuation rules of traffic levels and asphalt layer thickn...

  5. Effectiveness of Micro- and Nanomaterials in Asphalt Mixtures through Dynamic Modulus and Rutting Tests

    OpenAIRE

    Hui Yao; Zhanping You

    2016-01-01

    The objectives of this research are to use micro- and nanomaterials to modify the asphalt mixture and to evaluate the mechanical performance of asphalt mixtures. These micro- and nanomaterials, including carbon microfiber, Nanomer material, nanosilica, nonmodified nanoclay, and polymer modified nanoclay, were selected to blend with the control asphalt to improve the overall performance of the modified asphalt binders and mixtures. The microstructures of original materials and asphalt binders ...

  6. Modeling and Simulation of Flow and Formation Damage of Asphalt-Paved Roads

    OpenAIRE

    M. H. Alawi; M. M. El-Qadi; M. A. El-Ameen

    2013-01-01

    Porous asphalt is a standard asphalt built on aggregate storage bed which allows water to drain through it and reduces stormwater runoff. However, porosity of the porous asphalt and the storage bed may be effectively reduced due to trapping suspended solids from the water or from the asphalt damage. In this paper, we present mathematical modeling and numerical simulation of flow and damage of porous asphalt-paved roads. A mathematical model to describe the fine-particles transport carried by ...

  7. Microbial Life in a Liquid Asphalt Desert

    CERN Document Server

    Schulze-Makuch, Dirk; Antonio, Marina Resendes de Sousa; Ali, Denzil; Hosein, Riad; Song, Young C; Yang, Jinshu; Zaikova, Elena; Beckles, Denise M; Guinan, Edward; Lehto, Harry J; Hallam, Steven J

    2010-01-01

    An active microbiota, reaching up to 10 E+7 cells/g, was found to inhabit a naturally occurring asphalt lake characterized by low water activity and elevated temperature. Geochemical and molecular taxonomic approaches revealed novel and deeply branching microbial assemblages mediating anaerobic hydrocarbon degradation, metal respiration and C1 utilization pathways. These results open a window into the origin and adaptive evolution of microbial life within recalcitrant hydrocarbon matrices, and establish the site as a useful analog for the liquid hydrocarbon environments on Saturn's moon Titan.

  8. The Use of Coal Bottom Ash In Hot Mix Asphalt

    Directory of Open Access Journals (Sweden)

    Charles Begyina Kodjo Nketsiah

    2015-05-01

    Full Text Available Bottom ash is a waste material from coal burnt to generate electric power. It is incombustible and non-biodegradable; hence, the best way to dispose it is by recycling rather than incineration and land filling. Past research on bottom ash in road building have focused mainly on embankment filling, sub-base and base courses; except boiler slag which has received much attention in Hot Mix Asphalt (HMA. Bottom ash from Tanjung Bin Power Station was thus investigated through laboratory testing to justify its use in HMA construction in Malaysia. This Paper analysed the data with regards to performance in HMA. In the Marshall Mix design, the material largely satisfied the Stability, Flow and Stiffness requirements which were comparable to that of conventional aggregates, although void contents were a bit higher. When blended with granite, all the parameters were met. Contrary to past suggestions that bottom ash in HMA consumes more bitumen, the 6.4% (51.20g Optimum Bitumen Content (OBC achieved in this study does not necessarily translate into high consumption, compared to OBC of 5.3% (59.63g in the case of granite. The HMA also proved to be highly resistant to moisture-induced damage and satisfied the minimum JKR specification for Static Uniaxial Load Strain.

  9. Study on the hardening mechanism of cement asphalt binder

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    The hydration and hardening mechanism of cement asphalt binder(CAB) was studied.The early hydration process,hydration products and paste microstructure of CAB made by Portland cement and anionic asphalt emulsion were investigated by calorimetry,X-ray diffraction,and environmental scanning electron microscopy.The early hydration process of CAB can be characterized as 5 stages similar to those of Portland cement.There is no chemical reaction detected between cement and asphalt,hence no new hydration products other than those of Portland cement are produced.The hardening of CAB begins with the hydration of cement.When the hydration of cement comes into the acceleration period and its exothermic rate comes to the maximum,the coalescence of asphalt particles in asphalt emulsion is triggered.In the hardened system of CAB,it was found that the hydration products of cement form the skeleton and are covered by the continuous asphalt film.They formed an interpenetrating network system.The emulsifiers in the asphalt emulsion may retard the hydration process of cement.

  10. Evaluation of Hydrated Lime Filler in Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Mohammed Abbas Hasan Al-Jumaily

    2008-01-01

    Full Text Available Mineral filler is one of important materials and affecting on properties and quality of asphalt mixtures .There are different types of mineral filler depended on cost and quality , the matter encourages us to achieve this study to evaluate hydrated lime filler effects on properties of asphalt mixes related with strength and durability. Conventional asphaltic concrete mixtures with Portland cement and soft sandstone fillers and mixtures modified with hydrated lime were evaluated for their fundamental engineering properties as defined by Marshall properties , index of retained strength , indirect tensile strength , permanent deformation characteristics , and fatigue resistance .A typical dense graded mixture employed in construction of surface course pavement in Iraq in accordance with SCRB specifications was used .The materials used in this study included mineral aggregate materials (coarse and fine sizes were originally obtained from Najaf Sea quarries and two grades of asphalt cements produced from Daurah refinery which are D47 and D66 . The physical properties , stiffness modulus and chemical composition are evaluated for the recovered asphalt cement from prepared asphalt mixes containing various filler types .The paper results indicated that the addition of hydrated lime as mineral filler improved the permanent deformation characteristics and fatigue life and the use of hydrated lime will decrease the moisture susceptibility of the asphalt mixtures.

  11. Effect of fiber types on relevant properties of porous asphalt

    Institute of Scientific and Technical Information of China (English)

    WU Shao-peng; LIU Gang; MO Lian-tong; CHEN Zheng; YE Qun-shan

    2006-01-01

    The research was conducted to evaluate the effects of cellulose and polyester fibers on the properties of porous asphalt mixes,using the tests of draindown,abrasion,volumetric properties,rutting,and moisture damage. Images of scanning electron microscopy and X-ray computerized tomography were adopted to identify the microstructure of the fiber and inner stone skeleton of porous asphalt. The influence of rutting parameter (G*/sinδ) of asphalt modified by different fibers on the rutting resistance of the mixes was investigated. Based upon Mohr-Coulomb theory,the cohesion and the angle of internal friction of the mixes were derived from both indirect tension and unconfined compression strength. The experimental results indicate that fibers mainly stabilize asphalt binder and thicken asphalt film around aggregates. Furthermore,they result in the improved mechanical strength of porous asphalt mixes at high temperature slightly. From comparison analysis,cellulose fibers appear to perform better than polyester fibers in porous asphalt mixes.

  12. Pavement performance of asphalt mixtures containing silica%硅石沥青混合料的路用性能

    Institute of Scientific and Technical Information of China (English)

    郭乃胜; 王聪; 赵颖华

    2014-01-01

    The boiling water test was used to investigate adhe-siveness between silica and asphalt with different contents of hydrated lime added .Based upon the design theory of graded anti-skidding asphalt mixtures , the coarse aggregates retained on the 4.75 mm sieve were adopted for silica , fine aggregates passing the 4.75 mm sieve and filler were utilized for lime-stone.Marshall design method was performed to determine gradation composition design of asphalt mixtures containing silica, and the experimental section of asphalt pavement con-taining silica was chosen for construction with tracking detec-tion at a typical region .Results show that adhesiveness be-tween silica and asphalt can be improved by the addition of hydrated lime at 2% by the weight of asphalt , and the per-formance test results of asphalt mixtures containing silica with 2% hydrated lime added can meet the requirements of the technical specifications ( JTG F40-2004 ) , especially that presents favorable moisture susceptibility .The experimental pavement conditions display an appreciable usage .The tex-ture depth and British pendulum numbers of experimental pavement is higher than that of common asphalt pavement at the same route.Moreover, the texture depth and British pen-dulum numbers along with increasing time exhibit lower de-crease than that of common asphalt pavement in terms of tracking detection results .This means silica, as a kind of acid aggregate , may be used in the highway asphalt pavement by using appropriate gradations composition design and anti-stripping agent , which can improve the skidding resistance of asphalt pavement .%采用水煮法分析添加不同掺量消石灰的硅石与沥青的黏附性.根据级配型抗滑沥青混合料设计理论,筛孔4.75 mm以上的粗集料采用硅石,4.75 mm以下的集料采用石灰岩.基于马歇尔设计法进行硅石沥青混合料配合比设计及路用性能检验,并选择具有代表性路段进行硅石沥青路面

  13. Asphalt emulsion sealing of uranium mill tailings

    International Nuclear Information System (INIS)

    The use of asphalt emulsion to contain radon and radium in uranium tailings is being investigated at the Pacific Northwest Laboratory. Results of these studies indicate that a radon flux reduction of greater than 99% can be obtained using either a poured-on/sprayed-on seal (3.0 to 7.0 mm thick) or an admix seal (2.5 to 15.2 cm thick) containing about 18 wt % residual asphalt. A field test was carried out at the Grand Junction tailings pile in order to demonstrate the sealing process. A reduction in radon flux ranging from 4.5 to greater than 99% (76% average) was achieved using a 15.2 cm (6 in.) admix seal with a sprayed-on top coat. A hydrostatic stabilizer was used to apply the admix. This was followed by compaction to form the radon seal. Overburden was applied to provide a protective soil layer over the seal. Included in part of the overburden was a herbicide to prevent root penetration

  14. Conversion of asphalt into distillate products

    International Nuclear Information System (INIS)

    This paper reports the conversion of asphalt in a micro-autoclave under an inert atmosphere of nitrogen to lighter products. The influence of temperature, contact time and some catalysts, i.e. clay type; UTIMAC, HZSM-5 and sodium silicate, acidic type; phospho-tungstic acid, oxide type; ammonium hepta molybdate, silica gel, nickel oxide and alumina powder, chloride type; stannous chloride and aluminum chloride and modifiers like methyl iodide and coal, on the yield of liquid and gas products was studied. A marked effect of temperature on the yield of liquid as well as gas products was observed. Employment of clay type catalysts was found to be beneficial in term of yields of liquid products. Among the catalysts used; UTIMAC clay caused the maximum conversion to desired products. The other catalysts caused a decline in the yield of desired products because of coke formation due to condensation reactions catalyzed by these catalysts. The effect of concentration in the case of clay as catalyst was also studied, and synergistic effects were observed in terms of desired product yield. The study will be helpful in planning asphalt conversion processes into light oil fractions

  15. Asphalt as biological shielding against fusion neutrons

    International Nuclear Information System (INIS)

    For fusion experiments, thick biological radiation protection shields are necessary due to the deep penetration capability of the 14 MeV neutrons. A (D,T) neutron generator with a moderate output of around 1012 n/sec requires a concrete shielding of a wall thickness of 2 meters laterally and at the top of an experimental assembly. The cost for this biological shield may exceed the cost for most of the equipment for a fusion and/or hybrid experimental installation. Particularly, in Saudi Arabia, asphalt is very cheap and available in bulk quantities. As it is rich in hydrogen and carbon, it is worthwhile to investigate its shielding potential against fusion neutron. In the present work different biological shield configurations of asphalt at the wall of the experimental cavity for a research program being undertaken in Saudi Arabia, are investigated. The experimental cavity is approximated by a sphere of 5 meters radius. The yield of the neutron generator is taken as 1012 - 14 MeV - neutron/sec

  16. Warm mixes asphalt : Laboratory evaluation of two mix design methods

    OpenAIRE

    MAILLARD NUNES, Patrícia; DONY, Anne; KLINCEVICIUS, Mary; MOTTA, Rosângela; Bernucci, Liedi; DEL PRIORE, Claudio; Brosseaud, Yves; Gaudefroy, Vincent; COLIN, Johan

    2009-01-01

    From a French-Brazilian partnership among Escola Politécnica da Universidade de São Paulo (LTP - Laboratory of Pavement Technology), Ecole Spéciale de Travaux Publics ESTP (GREMACOR Laboratory) and Laboratoire Central des Ponts et Chaussées (LCPC Division SMIT), a study on warm mixes asphalt was developed. Since 2003, new asphalt mixes that are set between hot and cold mixes have been developed with the purpose of reducing mixing and compaction temperatures of hot mixes asphalt, yet maintain...

  17. Characterization of asphalt materials containing bio oil from michigan wood

    Science.gov (United States)

    Mills-Beale, Julian

    The objective of this research is to develop sustainable wood-blend bioasphalt and characterize the atomic, molecular and bulk-scale behavior necessary to produce advanced asphalt paving mixtures. Bioasphalt was manufactured from Aspen, Basswood, Red Maple, Balsam, Maple, Pine, Beech and Magnolia wood via a 25 KWt fast-pyrolysis plant at 500 °C and refined into two distinct end forms - non-treated (5.54% moisture) and treated bioasphalt (1% moisture). Michigan petroleum-based asphalt, Performance Grade (PG) 58-28 was modified with 2, 5 and 10% of the bioasphalt by weight of base asphalt and characterized with the gas chromatography-mass spectroscopy (GC-MS), Fourier Transform Infra-red (FTIR) spectroscopy and the automated flocculation titrimetry techniques. The GC-MS method was used to characterize the Carbon-Hydrogen-Nitrogen (CHN) elemental ratio whiles the FTIR and the AFT were used to characterize the oxidative aging performance and the solubility parameters, respectively. For rheological characterization, the rotational viscosity, dynamic shear modulus and flexural bending methods are used in evaluating the low, intermediate and high temperature performance of the bio-modified asphalt materials. 54 5E3 (maximum of 3 million expected equivalent standard axle traffic loads) asphalt paving mixes were then prepared and characterized to investigate their laboratory permanent deformation, dynamic mix stiffness, moisture susceptibility, workability and constructability performance. From the research investigations, it was concluded that: 1) levo, 2, 6 dimethoxyphenol, 2 methoxy 4 vinylphenol, 2 methyl 1-2 cyclopentandione and 4-allyl-2, 6 dimetoxyphenol are the dominant chemical functional groups; 2) bioasphalt increases the viscosity and dynamic shear modulus of traditional asphalt binders; 3) Bio-modified petroleum asphalt can provide low-temperature cracking resistance benefits at -18 °C but is susceptible to cracking at -24 °C; 3) Carbonyl and sulphoxide

  18. Discrete Element Simulation of Asphalt Mastics Based on Burgers Model

    Institute of Scientific and Technical Information of China (English)

    LIU Yu; FENG Shi-rong; HU Xia-guang

    2007-01-01

    In order to investigate the viscoelastic performance of asphalt mastics, a micro-mechanical model for asphalt mastics was built by applying Burgers model to discrete element simulation and constructing Burgers contact model. Then the numerical simulation of creep tests was conducted, and results from the simulation were compared with the analytical solution for Burgers model. The comparision snowed that the two results agreed well with each other, suggesting that discrete element model based on Burgers model could be employed in the numerical simulation for asphalt mastics.

  19. An investigation of the effectiveness of asphalt durability tests

    Science.gov (United States)

    Predoehl, N. H.; Kemp, G. R.

    1980-05-01

    Included are analyses which show that the effects of voids and aggregate porosity are less severe than the thermal oxidation effect in hot desert climates. A comparison of the results of laboratory tests for predicting asphalt hardening with the results for the field weathered briquettes show that none of the procedures is capable of adequately predicting asphalt weathering in a hot weathering site. A procedure was developed to approximate the effect produced at Indio in two years. Some correlation to briquette results was obtained. A climatic specification to control asphalt hardening in the hot climatic areas is proposed.

  20. Main Factors Impacting on the Performance of Rubber Asphalt%影响橡胶沥青路用性能的主要因素分析

    Institute of Scientific and Technical Information of China (English)

    邓洪宗

    2012-01-01

    The rubber asphalt specimens under different production parameters of mixing time and crumb rubber content were prepared to test its asphalt performance indicators such as penetration, ductility, softening point, elastic recovery and the Brookfield rotation viscosity. Combined with the modifying mechanism of polymer asphalt, the article studied the main influence factors in the rubber asphalt production process affecting its performance and its extent, and then put forward suggestions for improvement of rubber asphalt processing.%通过制备不同搅拌时间和胶粉掺量的橡胶沥青,测试橡胶沥青的三大基本指标、弹性恢复性能以及布氏旋转粘度值,对这两个重要生产工艺参数对橡胶沥青性能的影响规律进行了研究,并从聚合物改性沥青作用机理的角度对其进行了剖析,在此基础上提出了橡胶沥青加工工艺的改进建议。

  1. Experimental study of recycled asphalt mixtures with high percentages of reclaimed asphalt pavement (RAP)

    OpenAIRE

    Valdés Vidal, Gonzalo A.; Pérez Jiménez, Félix Edmundo; Miró Recasens, José Rodrigo; Martínez Reguero, Adriana Haydée; Botella Nieto, Ramón

    2011-01-01

    This paper presents an experimental study to characterize the mechanical behaviour of bituminous mixtures containing high rates of reclaimed asphalt pavement (RAP). Two semidense mixtures of 12 and 20 mm maximum aggregate size and containing 40 and 60% RAP, respectively (S-12 and S-20, in accordance with Spanish specifications), which were used for rehabilitation of a highway section, were evaluated. First, the effect of RAP variability on the recycled mixtures was analyzed. Their mecha...

  2. A review of the fundamentals of polymer-modified asphalts: Asphalt/polymer interactions and principles of compatibility.

    Science.gov (United States)

    Polacco, Giovanni; Filippi, Sara; Merusi, Filippo; Stastna, George

    2015-10-01

    During the last decades, the number of vehicles per citizen as well as the traffic speed and load has dramatically increased. This sudden and somehow unplanned overloading has strongly shortened the life of pavements and increased its cost of maintenance and risks to users. In order to limit the deterioration of road networks, it is necessary to improve the quality and performance of pavements, which was achieved through the addition of a polymer to the bituminous binder. Since their introduction, polymer-modified asphalts have gained in importance during the second half of the twentieth century, and they now play a fundamental role in the field of road paving. With high-temperature and high-shear mixing with asphalt, the polymer incorporates asphalt molecules, thereby forming a swallowed network that involves the entire binder and results in a significant improvement of the viscoelastic properties in comparison with those of the unmodified binder. Such a process encounters the well-known difficulties related to the poor solubility of polymers, which limits the number of macromolecules able to not only form such a structure but also maintain it during high-temperature storage in static conditions, which may be necessary before laying the binder. Therefore, polymer-modified asphalts have been the subject of numerous studies aimed to understand and optimize their structure and storage stability, which gradually attracted polymer scientists into this field that was initially explored by civil engineers. The analytical techniques of polymer science have been applied to polymer-modified asphalts, which resulted in a good understanding of their internal structure. Nevertheless, the complexity and variability of asphalt composition rendered it nearly impossible to generalize the results and univocally predict the properties of a given polymer/asphalt pair. The aim of this paper is to review these aspects of polymer-modified asphalts. Together with a brief description of

  3. City ground: constructed totality:Artistic and architectural preoccupations with asphalt in the US west coast 1952-1972

    OpenAIRE

    Ewing, Suzanne

    2012-01-01

    Through close study of selected artistic and architectural preoccupations with city ground, and the asphalt ground of the modern US west coast city in the mid-twentieth century in particular, this paper explores the geographical idea of the city as a totality of construction, and how this has influenced and intersected subsequent architectural practices of study, research and design practice. The photographic content of key constructed works from 1952 until 1972: a short film by Charles and R...

  4. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Pauul J. Tikalsky

    2004-10-31

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: (1) a statistically sound evaluation of the characterization of foundry sand, (2) a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and (3) the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at N{sub ini}, N{sub des}, and N{sub max}. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  5. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Tikalsky, Paul J. [Pennsylvania State Univ., University Park, PA (United States); Bahia, Hussain U. [Univ. of Wisconsin, Madison, WI (United States); Deng, An [Pennsylvania State Univ., University Park, PA (United States); Snyder, Thomas [Univ. of Wisconsin, Madison, WI (United States)

    2004-10-15

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: a statistically sound evaluation of the characterization of foundry sand, a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at Nini, Ndes, and Nmax. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  6. Respirable crystalline silica exposures during asphalt pavement milling at eleven highway construction sites.

    Science.gov (United States)

    Hammond, Duane R; Shulman, Stanley A; Echt, Alan S

    2016-07-01

    Asphalt pavement milling machines use a rotating cutter drum to remove the deteriorated road surface for recycling. The removal of the road surface has the potential to release respirable crystalline silica, to which workers can be exposed. This article describes an evaluation of respirable crystalline silica exposures to the operator and ground worker from two different half-lane and larger asphalt pavement milling machines that had ventilation dust controls and water-sprays designed and installed by the manufacturers. Manufacturer A completed milling for 11 days at 4 highway construction sites in Wisconsin, and Manufacturer B completed milling for 10 days at 7 highway construction sites in Indiana. To evaluate the dust controls, full-shift personal breathing zone air samples were collected from an operator and ground worker during the course of normal employee work activities of asphalt pavement milling at 11 different sites. Forty-two personal breathing zone air samples were collected over 21 days (sampling on an operator and ground worker each day). All samples were below 50 µg/m(3) for respirable crystalline silica, the National Institute for Occupational Safety and Health recommended exposure limit. The geometric mean personal breathing zone air sample was 6.2 µg/m(3) for the operator and 6.1 µg/m(3) for the ground worker for the Manufacturer A milling machine. The geometric mean personal breathing zone air sample was 4.2 µg/m(3) for the operator and 9.0 µg/m(3) for the ground worker for the Manufacturer B milling machine. In addition, upper 95% confidence limits for the mean exposure for each occupation were well below 50 µg/m(3) for both studies. The silica content in the bulk asphalt material being milled ranged from 7-23% silica for roads milled by Manufacturer A and from 5-12% silica for roads milled by Manufacturer B. The results indicate that engineering controls consisting of ventilation controls in combination with water-sprays are

  7. The wind resistance of asphalt roofing shingles

    Science.gov (United States)

    Dixon, Craig Robert

    Asphalt shingle roofing is the leading cause of hurricane wind-related insured losses in residential buildings. Damage statistics generated from recent hurricanes indicate shingle roofs sustain damage in wind velocities below design-level with damage frequency increasing with shingle roof age. The objective of this dissertation is the identification of primary mechanisms triggering the failure of shingle roof systems in wind. The research goal is to reduce future shingle roof wind damage and improve our ability to predict asphalt shingle wind resistance. Five studies comprising this dissertation addressed the adhesive consistency and strength of aged asphalt shingles, system-level wind resistance, and the load model underpinning the ASTM D7158 wind test standard. The most significant and unexpected finding was partially unsealed shingles on field, hip, and ridge locations on Florida and Texas homes. Location on the shingle's sealant strip where unsealed and failure mode were consistent at each location. Total quantity of partially unsealed shingles in the field of the roof significantly increased with age, aligning with damage statistics. Full-scale wind tunnel tests demonstrate partially unsealed shingles are more vulnerable than fully sealed due to increased distributed force on sealant strip and concentrated force at the adhered and non-adhered interface. Uplift resistance was measured in artificially and naturally aged shingles. For artificially aged shingles, one of three products evaluated had statistically significant decreases in mean uplift resistance as exposure time increased. However, resistance was above design-level at all exposure test intervals. Naturally aged shingles also had resistance above design-level. Combined results demonstrate that reduced uplift capacity can occur, but high initial bond strength promotes long-term uplift resistance. Wind loads exerted on the shingles sealant strip load path were directly measured on fully sealed and

  8. Storm Water General Permit 3 for Rock and Asphalt

    Data.gov (United States)

    Iowa State University GIS Support and Research Facility — General permit #3 for storm water discharges associated with industrial activity for Asphalt Plants, Concrete Batch Plants, Rock Crushing Plants and Construction...

  9. Performance Characterization of Polymer Modified Asphalt Binders and Mixes

    Directory of Open Access Journals (Sweden)

    Nikhil Saboo

    2016-01-01

    Full Text Available Fatigue sensitivity of four different asphalt binders and three different asphalt mixes was evaluated in the study. Binders were subjected to Linear Amplitude Sweep (LAS test at three temperatures of 10, 20, and 30°C. Four-point beam bending test (4PBBT was conducted on the asphalt mixes at a temperature of 20°C for strain amplitudes varying from 200 to 1000 microstrains. Tests like retained Marshall Stability and indirect tensile strength (ITS were also carried out to judge the mix performance. Experimental studies demonstrated that elastomeric modified binder and mixes gave the best performance in fatigue. Plastomeric modification was found to be highly strain susceptible and resulted in poor fatigue performance. The fatigue life of stone mastic asphalt (SMA was found to be almost five times higher than the dense graded mixes. For similar strain levels, the results of LAS test could be linearly correlated with the 4PBBT results.

  10. Effect of moisture on the aging behavior of asphalt binder

    Science.gov (United States)

    Ma, Tao; Huang, Xiao-Ming; Mahmoud, Enad; Garibaldy, Emil

    2011-08-01

    The moisture aging effect and mechanism of asphalt binder during the in-service life of pavement were investigated by laboratory simulating tests. Pressure aging vessel (PAV) test simulating the long-term aging of binder during the in-service life of pavement was modified to capture the long-term moisture aging effect of binder. Penetration grade tests including penetration test, soften point test, and ductility test as well as Superpave™ performance grade tests including viscosity test, dynamic shear rheometer test, and bending beam rheometer test were conducted to fully evaluate the moisture aging effect of binder. Fourier transform infrared spectroscopy test and Gel-permeation chromatography test were applied to provide a fundamental understanding of the moisture aging mechanism of binder. The results indicate that moisture condition can accelerate the aging of asphalt binder and shorten the service life of asphalt binder. The modified PAV test with moisture condition can well characterize the moisture aging properties of asphalt binder.

  11. Rutting Resistance of Asphalt Overlay with Multilayer Wheel Tracking Test

    Institute of Scientific and Technical Information of China (English)

    LIAO Weidong; CHEN Zheng; WU Shaopeng; MO Liantong; LIU Gang

    2006-01-01

    The rutting resistance of multilayer asphalt overlay was researched by using laboratory wheel tracking test. The effects of loading level and test temperature on rutting resistance of asphalt overlay structure were evaluated by means of multilayer specimens .In comparison with multilayer tests, standard specimens of various layers were also conducted to evaluate the rutting resistance. Experimental results indicated that the test temperature and applied load have a significant effect on rutting resistance of asphalt concrete. Higher test temperature and heavier applied load resulted in higher rut depths. In addition, the mutilayer wheel tracking test has been demonstrated to be a more reasonable solution in evaluation on rutting resistance of asphatt pavement structure beasuse it reflects the cumulative permanent deformation in all of asphalt layers.

  12. 信息动态%A Research on the Pavement Performance of Warm Mix Buton Mastic Asphalt

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    Compositing modified asphalt mixture is a kind of asphalt mixture which uses Buton Mastic Asphalt(BMA) and warm modifier compound modification. It is proved that the composite modified asphalt mixture technology can greatly reduce the mixing temperature, save energy and protect the environment, and can guarantee good road performance. Employing Buton Mastic Asphalt as modifier can obviously increase the high temperature stability of asphalt mixture, with little impact on low temperature performance.

  13. Effect of Carbon Nanofiber on Mechanical Behavior of Asphalt Concrete

    Directory of Open Access Journals (Sweden)

    Saeed Ghaffarpour Jahromi

    2015-09-01

    Full Text Available Uses of fibers to improve material properties have a scientific background in recent years in civil engineering. Use of Nanofiber reinforcement of materials refers to incorporating materials with desired properties within some other materials lacking those properties. Use of fibers for improvement is not a new phenomenon as the technique of fiber-reinforced bitumen began as early as 1950, but using nanofiber is a new idea. In this research the mechanical properties of asphalt mixture that have been modified with carbon nanofiber were investigated using mechanical tests, which can improve the performance of flexible pavements. To evaluate the effect of nanofiber contents on bituminous mixtures, laboratory investigations were carried out on the samples with and without nanofibers. During the course of this study, various tests were undertaken applying the Marshall test, indirect tensile test, resistance to fatigue cracking by using repeated load indirect tensile test and creep test. Carbon nanofiber exhibited consistency in results and it was observed that the addition of nanofiber can change the properties of bituminous mixtures, increase its stability and decrease the flow value. Results indicate that nanofiber have the potential to resist structural distress in the pavement and thus improve fatigue by increasing resistance to cracks or permanent deformation, when growing traffic loads. On the whole, the results show that the addition of carbon nanofiber will improve some of the mechanical properties such as fatigue and deformation in the flexible pavement.

  14. Asphalt Carriers from Kraljevica Shipyard – Constructional and Technological Aspects

    OpenAIRE

    Grubišić, R.

    2006-01-01

    After presenting the design development of the asphalt carrier Asphalt Seminole and her sister-ships in the article published in the previous issue of Brodogradnja (No. 1/2006), in this article the structural analysis made in the design stage and some constructional and technological specifities during the building stage are presented. Special emphasis is given to the presentation of the structional connection between the hull and the cargo tanks with the description of the elastic vertical s...

  15. Comparative Study of French and Chinese Asphalt Pavement Design Methods

    OpenAIRE

    Pierre Guy Atangana Njock; Li Yueguang

    2015-01-01

    This study deals with the comparison of French and Chinese approaches for the design of flexible pavement. The Finite Element Analysis (FEA using ANSYS) was used to compute and compare the mechanical responses in four typical pavement structures used in France and China, for respective axle type and loads. The study concluded that the maximum deflection in typical structure of stabilized asphalt pavement in China is greater than that obtained in the typical treated bases asphalt pavement in F...

  16. Full-Depth Pavement Reclamation with Foamed Asphalt: Final Report

    OpenAIRE

    Jones, David; P. Fu; Harvey, John T; Halles, F.

    2008-01-01

    A comprehensive study on full-depth reclamation (FDR) of pavements with foamed asphalt has been completed for the California Department of Transportation by the University of California Pavement Research Center. A literature review revealed that very little research had been carried out on the reclamation of thick asphalt pavements (multiple overlays over a relatively weak base or subgrade). A mechanistic sensitivity analysis was carried out to identify key variables in the design of recycled...

  17. Mechanistic and Economical Characteristics of Asphalt Rubber Mixtures

    OpenAIRE

    Mena I. Souliman; Annie Eifert

    2016-01-01

    Load associated fatigue cracking is one of the major distress types occurring in flexible pavement systems. Flexural bending beam fatigue laboratory test has been used for several decades and is considered to be an integral part of the new superpave advanced characterization procedure. One of the most significant solutions to prolong the fatigue life for an asphaltic mixture is to utilize flexible materials as rubber. A laboratory testing program was performed on a conventional and Asphalt Ru...

  18. The temperature effect on the reflective cracking of asphalt overlays

    OpenAIRE

    Minhoto, Manuel; Pais, Jorge; Pereira, Paulo

    2008-01-01

    This paper presents a study about the influence of temperature on the reflective cracking in a flexible road pavement through the evaluation of the asphalt overlay damage associated to traffic and temperature variations throughout a year. This study was developed from a numerical simulation of the asphalt overlay behaviour based on a three-dimensional finite-element analysis, considering the simultaneous loading of traffic and temperature variations. A mechanistic-based overlay design method ...

  19. Effect of base bitumen composition on asphalt rubber binder properties

    OpenAIRE

    Partl, M.N.; Ould-Henia, M.; Dumont, A.-G.

    2008-01-01

    The asphalt rubber blend properties are strongly related to its base components properties. The base bitumen composition is considered as a key factor influencing the final rheological properties of asphalt rubber binder. This paper describes results from a laboratory investigation of the interaction between crumb rubber and different composition bitumen according to the wet process. The bitumen composition is determined according to the SARA decomposition approac...

  20. Asphalt in carbon-14-dated archaeological samples from Terqa, Syria

    International Nuclear Information System (INIS)

    The results are reported of an organic geochemical study to verify contamination in 14C dated archaeological samples, which could account for much older apparent ages than expected. The data indicate that ancient asphalt must be the source of contamination, showing that caution should be exercised, in interpreting 14C dates of archaeological samples from areas containing asphalt or other fossil fuel deposits. (U.K.)

  1. Preparation of Flame Retardant Modified with Titanate for Asphalt Binder

    OpenAIRE

    2014-01-01

    Improving the compatibility between flame retardant and asphalt is a difficult task due to the complex nature of the materials. This study explores a low dosage compound flame retardant and seeks to improve the compatibility between flame retardants and asphalt. An orthogonal experiment was designed taking magnesium hydroxide, ammonium polyphosphate, and melamine as factors. The oil absorption and activation index were tested to determine the effect of titanate on the flame retardant additive...

  2. Building Asphalt Pavement with SBS-based Compound Added Using a Dry Process in Greenland

    DEFF Research Database (Denmark)

    Lee, Hosin; Kim, Yongjoo; Geisler, Nivi;

    2009-01-01

    PMA where it is formulated to melt and blend with asphalt quickly during a batch mixing process. The main objectives of this study are to (1) build asphalt pavement using asphalt mixtures with SBS-based compound added using a “dry” process at the batch plant and (2) evaluate its performance under......-based compound seemed to affect the asphalt mix to become more flexible under the heavy loads. By adding SBS-based compound to asphalt mixtures using a “dry” process, it is expected that the pavement would become more resistant to rutting than a typical asphalt mixture used in Greenland while enduring its arctic...

  3. Rutting based evaluation of asphalt mixes

    International Nuclear Information System (INIS)

    Pavement rutting is one of the most common and destructive pavement distresses being observed in flexible pavements, which is primarily due to a-x-le loads that exceed legal limit and high ambient temperatures, and also poor mix design is one of the cause of rutting. The drastic increase in traffic volume during last few decades has resulted in premature pavement fillers of almost the whole road structure in Pakistan. In this scenario it is the time to investigate this problem and propose appropriate solution. Physical properties of aggregates and bitumen were evaluated in the laboratory. Mechanical Properties of three mixes. i.e., Marshall, Super pave and Stone Mastic Asphalt (SMA) were evaluated by performing creep test. indirect tensile test and dynamic modulus in order to compare the performance of mixes under prevailing load and environmental conditions of Pakistan. The study revealed that Super pave mixes performed better than Marshall and SMA. (author)

  4. Rheological properties of asphalt mixtures containing various fibers

    Institute of Scientific and Technical Information of China (English)

    叶群山; 吴少鹏; 陈筝; 刘至飞

    2008-01-01

    Rheological characteristics of fiber-modified asphalt mixture were investigated.Cellulous fiber,polyester fiber and mineral fiber were used as additives for asphalt mixture,and the dosages were 0.3%,0.3%,0.4%,respectively.Dynamic modulus test using superpave simple performance tester(SPT) was adopted to study the dynamic modulus and phase angle for the control mixture and fiber-modified ones at various temperatures and frequencies.Test results show that the rheological properties can be improved significantly by the addition of various fibers.The dynamic modulus increases with the increase of frequency,and the phase angle decreases with the increase of frequency.When various fibers are used,the dynamic modulus increases and phase angle decreases at each frequency.This indicates that the stiffness and the elastic portion of fiber-modified asphalt mixtures can be enhanced when various fibers are used,which results in the change of viscoelastic properties of mixtures.The creep test results show that the total strain and the permanent strain of asphalt mixtures during load-unload cycle can be significantly reduced,which results in the improvement of resistance to permanent deformation for asphalt mixtures containing various fiber additives.The Burgers model can be employed effectively to illustrate the rheological properties of fiber modified asphalt mixtures.

  5. Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

    Directory of Open Access Journals (Sweden)

    Yongjoo Kim

    2013-01-01

    Full Text Available This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of the fiber and the other mixtures, which included the conventional recycled foamed asphalt (RFA mixtures; the cement reinforced recycled foamed asphalt (CRFA mixtures; the semihot recycled foamed asphalt (SRFA mixtures; and recycled hot-mix asphalt (RHMA mixtures. It is found that the FRFA mixture shows higher Marshall stability than the RFA and SRFA mixtures, higher indirect tensile strength than the RFA mixture, and higher rut resistance than the RFA, SRFA, and RHMA mixtures as seen from the wheel tracking test.

  6. Effects of Fibers on the Dynamic Properties of Asphalt Mixtures

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    The dynamic characteristics of fiber-modified asphalt mixture were investigated. Cellulose fiber, polyester fiber and mineral fiber were used as additives for asphalt mixture, and the dosage was 0.3%, 0.3%,0.4%, respectively. Dynamic modulus test using SuperPave simple performance tester (SPT) was conducted to study the dynamic modulus (E*) and phase angle (δ) for the control asphalt mixture and fiber-modified ones at various temperatures and frequencies. Experimental results show that all fiber-modified asphalt mixtures have higher dynamic modulus compared with control mixture. The dynamic modulus master curves of each type of asphalt mixtures are determined based on nonlinear least square regression in accordance with the timetemperature superposition theory at a control temperature (21.1 ℃). The fatigue parameter E*×sinδ and rutting parameter E*/sinδ of asphalt mixture are adopted to study the fatigue and rutting-resistance properties, and experimental results indicate that such properties can be improved by fiber additives.

  7. APPLICATION OF LOW TEMPERATU RE PROPERTIES IMPROVEMENT ASPHALT TO REPAIRE WORK OF RO CK FILL DAM WITH ASPHALT FACING

    Science.gov (United States)

    Shimazaki, Masaru; Tsunoo, Takashi; Kasahara, Atsushi

    The low temperature properties improvement asphalt that is no decreasing the transformation follow and the stress relaxation properties at the low temperature was developed. It aimed at properties of PG64-28 (lowest temperature 28 degree C and maximum temperature 64 degree C that was able to be used) from PG (Performance Grade) of mix design method SUPERPAVE (Superior Performance Pavement) of new road-building plan SHRP (Strategic Highway Research Program) in the United States when developing. When the repair work of the rock fill dam with asphalt facing located in Kyogoku-cho Abuta-gun Hokkaido was planned, the applicability of the developed asphalt was verified. As for the verification outcome and the developed asphalt, it was proven that it was applied to the repair construction, and there was no problem in manufacturing and construction.

  8. Sensitivity analysis of longitudinal cracking on asphalt pavement using MEPDG in permafrost region

    Directory of Open Access Journals (Sweden)

    Chen Zhang

    2015-02-01

    Full Text Available Longitudinal cracking is one of the most important distresses of asphalt pavement in permafrost regions. The sensitivity analysis of design parameters for asphalt pavement can be used to study the influence of every parameter on longitudinal cracking, which can help optimizing the design of the pavement structure. In this study, 20 test sections of Qinghai–Tibet Highway were selected to conduct the sensitivity analysis of longitudinal cracking on material parameter based on Mechanistic-Empirical Pavement Design Guide (MEPDG and single factorial sensitivity analysis method. Some computer aided engineering (CAE simulation techniques, such as the Latin hypercube sampling (LHS technique and the multiple regression analysis are used as auxiliary means. Finally, the sensitivity spectrum of material parameter on longitudinal cracking was established. The result shows the multiple regression analysis can be used to determine the remarkable influence factor more efficiently and to process the qualitative analysis when applying the MEPDG software in sensitivity analysis of longitudinal cracking in permafrost regions. The effect weights of the three parameters on longitudinal cracking in descending order are air void, effective binder content and PG grade. The influence of air void on top layer is bigger than that on middle layer and bottom layer. The influence of effective asphalt content on top layer is bigger than that on middle layer and bottom layer, and the influence of bottom layer is slightly bigger than middle layer. The accumulated value of longitudinal cracking on middle layer and bottom layer in the design life would begin to increase when the design temperature of PG grade increased.

  9. Quantitative exposure matrix for asphalt fume, total particulate matter, and respirable crystalline silica among roofing and asphalt manufacturing workers.

    Science.gov (United States)

    Fayerweather, William E; Trumbore, David C; Johnson, Kathleen A; Niebo, Ronald W; Maxim, L Daniel

    2011-09-01

    This paper summarizes available data on worker exposures to asphalt fume (soluble fraction), total particulate matter, and respirable crystalline silica (quartz) [hereinafter RCS] over a 30-year period in Owens Corning's asphalt production and roofing manufacturing plants. For the period 1977 through 2006, the air-monitoring database contains more than 1,400 personal samples for asphalt fume (soluble fraction), 2,400 personal samples for total particulate, and 1,300 personal samples for RCS. Unique process-job categories were identified for the asphalt production and roofing shingle manufacturing plants. Quantitative exposures were tabulated by agent, process-job, and calendar period to form an exposure matrix for use in subsequent epidemiologic studies of the respiratory health of these workers. Analysis of time trends in exposure data shows substantial and statistically significant exposure reductions for asphalt fume (soluble fraction), total particulate matter, and respirable crystalline silica at Owens Corning plants. Cumulative distribution plots for the most recent sampling period (2001-2006) show that 95% of the asphalt fume (soluble fraction) measurements were less than 0.25 mg/m3; 95% of the total particulate measurements were less than 2.2 mg/m3; and 95% of the RCS measurements were less than 0.05 mg/m3. Several recommendations are offered to improve the design of future monitoring efforts. PMID:21879950

  10. Study on Pavement Performance of Rubber Asphalt Prepared with Diesel Activated Rubber Powder%柴油活化橡胶粉制备橡胶沥青路用性能研究

    Institute of Scientific and Technical Information of China (English)

    何东坡; 王浩

    2013-01-01

    In order to improve modification effect of rubber powder on asphalt and reduce its influence on original asphalt component, diesel is used as addition agent to activate rubber powder and then the pavement performance of diesel activated rubber asphalt is studied and compared to that of ordinary rubber asphalt. Then the mass ratio of rubber powder to diesel is confirmed to be 2: 1 and the base asphalt is Daqing AH-#90. The result shows that the law on how the diameter and content of the powder affecting the performance of activated rubber asphalt is the same as that on ordinary rubber asphalt; both the high-temperature behavior and elastic recovery performance of diesel activated rubber asphalt is inferior to those of ordinary one but both the low-temperature behavior and construction performance is superior.%为提高橡胶粉对沥青的改性效果,减少橡胶粉对原状沥青组分的影响,采用助剂柴油活化处理橡胶粉,研究了柴油活化橡胶沥青的路用性能,并与普通橡胶沥青的相关性能进行对比.确定了橡胶粉与柴油的质量比为2:1,基质沥青为黑龙江大庆AH-#90.结果表明:胶粉粒径、胶粉掺量对活化橡胶沥青性能的影响规律与普通橡胶沥青一样,柴油活化橡胶沥青的高温性能和弹性恢复性能不如普通橡胶沥青,低温性能和施工性能好于普通橡胶沥青.

  11. The Effect of Joint Width on Structural Performance of Asphalt Block Pavements

    Directory of Open Access Journals (Sweden)

    Ahmed Abdelgalil

    2014-02-01

    Full Text Available Asphalt blocks have been occasionally used around the world as a road pavement, but there have been very limited studies being done to evaluate the effect of joint width (spacing between the blocks on the structural performance of asphalt paving blocks. This study explains the experimental study to assess the performance and properties of asphalt paving blocks laid with different joint widths between the blocks i.e., 0, 2 and 3 mm, respectively. A total of 250 asphalt paving blocks was manufactured and tested in the laboratory to ascertain the density, air voids, the compressive strength and the rut depth and displacement occurred in asphalt paving block. The design compressive load of single asphalt paving block is 166 kN. The test results showed that the joint width plays a vital role on the performance of asphalt block pavement. Asphalt paving blocks were laid as closely in contact as possible (0 mm yields the best structural performance.

  12. The road that's taken : Alberta's bitumen and the world of asphalt

    International Nuclear Information System (INIS)

    Approximately one third of the bitumen produced by the oil sands industry in Canada is used as asphalt in roads and roofing materials. Crude oils used for asphalt production require very little refining. The asphalt market has become a key profit centre for some Cold Lake operators. Imperial Oil has established a research centre devoted to asphalt production at its Sarnia-based refinery. A decline in heavy oil supplies from Mexico and Venezuela has left Canada with a larger margin of the asphalt market. Industry leaders predict that demand for asphalt products will grow by 2.6 per cent per year. A sharp increase in asphalt prices led to many construction delays in 2007. Trials are now being conducted on a new warm mix paving technology that allows users to lower the temperature of asphalt by 20 to 30 degrees C when paving. 2 figs

  13. Physico-mechanical properties of asphalt concrete based on road bitumen modified by rapeseed oil epoxide

    OpenAIRE

    Nykypanchuk, Mykhailo; Hrynchuk, Yurii; Olchovyk, Mykola

    2013-01-01

    The investigation results of type B fine asphalt concrete and its form modified by rapeseed oil epoxide are represented. The efficiency of ERO addition and its positive effect on the physico-mechanical properties of asphalt concrete has been established.

  14. Asphalt Roofing Shingles Into Energy Project Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Jameson, Rex, PE

    2008-04-28

    Based on a widely cited September, 1999 report by the Vermont Agency of Natural Resources, nearly 11 million tons of asphalt roofing shingle wastes are produced in the United States each year. Recent data suggests that the total is made up of about 9.4 million tons from roofing tear-offs and about 1.6 million tons from manufacturing scrap. Developing beneficial uses for these materials would conserve natural resources, promote protection of the environment and strengthen the economy. This project explored the feasibility of using chipped asphalt shingle materials in cement manufacturing kilns and circulating fluidized bed (CFB) boilers. A method of enhancing the value of chipped shingle materials for use as fuel by removing certain fractions for use as substitute raw materials for the manufacture of new shingles was also explored. Procedures were developed to prevent asbestos containing materials from being processed at the chipping facilities, and the frequency of the occurrence of asbestos in residential roofing tear-off materials was evaluated. The economic feasibility of each potential use was evaluated based on experience gained during the project and on a review of the well established use of shingle materials in hot mix asphalt. This project demonstrated that chipped asphalt shingle materials can be suitable for use as fuel in circulating fluidized boilers and cement kilns. More experience would be necessary to determine the full benefits that could be derived and to discover long term effects, but no technical barriers to full scale commercial use of chipped asphalt shingle materials in these applications were discovered. While the technical feasibility of various options was demonstrated, only the use of asphalt shingle materials in hot mix asphalt applications is currently viable economically.

  15. Investigation of Primary Causes of Load-Related Cracking in Asphalt Concrete Pavement in North Carolina

    Science.gov (United States)

    Park, Hong Joon

    This dissertation presents causes of cracking in asphalt concrete pavement in North Carolina through field investigation and laboratory experiments with field extracted material. North Carolina is experiencing higher than anticipated rates of fatigue cracking compared to other state. These higher than expected rates could be reflective of the national trends in mix design practice or could be caused by structural pavement failures. The problems associated with premature cracking in North Carolina pavements point to the need to evaluate the North Carolina Department of Transportation (NCDOT) mixes, processes, and measures to ensure that these factors properly balance the goals of preventing cracking and minimizing permanent deformation. Without solid data from in-service pavements, any conclusions regarding the causes of these failures might be pure conjecture. Accordingly, this research examines material properties through laboratory experiments using field-extracted materials and investigates in situ pavements and pavement structure. In order to assess condition of existing pavement, alligator cracking index (ACI) was developed. The asphalt content in the top layer that exhibits top-down cracking or bottom-up cracking has a proportional relationship to ACI values. The air void content in a bottom layer that exhibits top-down cracking or bottom-up cracking shows an inverse proportional relationship to ACI values. These observations reflect reasonable results. A comparison between ACI and asphalt film thickness values does not produce noteworthy findings, but somewhat reasonable results are evident once the range of comparison is narrowed down. Thicker film thicknesses show higher ACI values. From field core visual observations, road widening is identified as a major cause of longitudinal cracking. Regions with observed layer interface separation tend to have low ACI values. Through tensile strain simulation based on actual field conditions, it is observed that

  16. Recycling of polyethylene terephthalate (PET plastic bottle wastes in bituminous asphaltic concrete

    Directory of Open Access Journals (Sweden)

    Adebayo Olatunbosun Sojobi

    2016-12-01

    Full Text Available This research sheds light on the concept of eco-friendly road construction which comprises eco-design, eco-extraction, eco-manufacturing, eco-construction, eco-rehabilitation, eco-maintenance, eco-demolition, and socioeconomic empowerment. It also revealed the challenges being faced in its adoption and the benefits derivable from its application. Furthermore, the effects of recycling PET plastic bottle wastes produced in North Central Nigeria in bituminous asphaltic concrete (BAC used in flexible pavement construction were also evaluated. The mix design consists of 60/70 penetration-grade asphaltic concrete (5%, 68% coarse aggregate, 6% fine aggregate, and 21% filler using the dry process at 170°C. The optimum bitumen content (OBC for conventional BAC was obtained as 4% by weight of total aggregates and filler. Polymer-coated aggregate (PCA-modified BAC seems preferable because it has the potential to utilize more plastic wastes with a higher optimum plastic content (OPC of 16.7% by weight of total aggregates and filler compared to that of 9% by weight of OBC achieved by PMB-BAC. For both PMB- and PCA-modified BAC, an increase in air void, void in mineral aggregate, and Marshall stability were observed. Eco-friendly road construction which recycles PET wastes should be encouraged by government considering its potential environmental and economic benefits.

  17. 温再生沥青混合料路用性能的试验研究%Research on the pavement performance of warm- recycled asphalt mixture

    Institute of Scientific and Technical Information of China (English)

    张德豪; 刘岩

    2015-01-01

    温再生沥青混合料是一种基于温拌沥青技术的新型再生沥青混合料,实现了旧沥青混合料(RAP)循环利用和节能减排的双重目标。本文通过与热再生沥青混合料的对比试验,研究了不同旧料掺量下温再生沥青混合料的路用性能。结果表明:温再生沥青混合料各项指标均已接近或达到了热再生沥青混合料的性能,而且旧料的掺配率可以提高10%左右;旧料掺量为20~30%时,温再生混合料的性能良好,可用于城市道路沥青路面的建设。%Warm-recycled asphalt mixture is a new type of pavement material that can realize the RAP recycling and energy saving and emission reduction. Trough the comparative test of hot-recycled asphalt mixture, the article studied the comprehensive pavement performance of warm-recycled asphalt mixture with the addition of different reclaimed asphalt pavement(RAP) admixture amount. The results showed that: all indicators of the warm- recycled asphalt mixture were close to or reached the performance of hot-recycled asphalt mixture,and the admixture amount of RAP can be improved about 10%. The RAP content should be among 20~30% when the WMA recycled mixture used in high grade highway construction.

  18. The Effect of Joint Width on Structural Performance of Asphalt Block Pavements

    OpenAIRE

    Ahmed Abdelgalil; Hasanan Nor

    2014-01-01

    Asphalt blocks have been occasionally used around the world as a road pavement, but there have been very limited studies being done to evaluate the effect of joint width (spacing) between the blocks on the structural performance of asphalt paving blocks. This study explains the experimental study to assess the performance and properties of asphalt paving blocks laid with different joint widths between the blocks i.e., 0, 2 and 3 mm, respectively. A total of 250 asphalt paving blocks was manuf...

  19. LABORATORY SIMULATION OF POROUS ASPHALT PARKING LOT SYSTEM AND MIX DESIGN FOR STORM WATER MANAGEMENT

    OpenAIRE

    M.O. Hamzah; Z. F. M. JAAFAR; Ahmad, F

    2013-01-01

    Porous asphalt pavement was initially developed for the purpose of improving road safety, best candidate material for quiet pavement and to avoid aquaplaning and skidding in wet weather. However, from previous studies, porous asphalt is able to mitigate surface runoff. Porous asphalt parking lots with underlying reservoir course perform as additional temporary water storage matrix that enables reduction of flash flood. This paper elaborates the development of a new porous asphalt aggregate g...

  20. Structural and Thermal Analysis of Asphalt Solar Collector Using Finite Element Method

    OpenAIRE

    Jinshah Basheer Sheeba; Ajith Krishnan Rohini

    2014-01-01

    The collection of solar energy using asphalt pavements has got a wide importance in the present energy scenario. Asphalt pavements subjected to solar radiation can reach temperature up to 70°C because of their excellent heat absorbing property. Many working parameters, such as pipe diameter, pipe spacing, pipe depth, pipe arrangement, and flow rate, influence the performance of asphalt solar collector. Existing literature on thermal energy extraction from asphalt pavements is based on the sma...

  1. Optimization of asphalt rubber hot mixes based on performance laboratory tests

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Márcio Muniz de; Pais, Jorge C.; Pereira, Paulo A. A.

    2003-01-01

    Asphalt binders modified with crumb rubber recycled from ground tires have been successfully used in asphalt mixtures improving the mechanical and functional behaviour of the pavements. This paper shows the influence of several factors that affect the behaviour of asphalt-rubber (AR) and of hot mixes made with this material. Modified binders were prepared using a straight binder with 35/50 penetration and rubber obtained by the environmental process. Samples of asphalt-rubber w...

  2. Visualizing asphalt roller trajectories in context: acquiring, processing, and representing sensor readings

    OpenAIRE

    Vasenev, Alexandr Nikolajevitsj

    2015-01-01

    The asphalt compaction process relies heavily on the skills and knowledge of roller operators who act alongside other stakeholders involved in asphalt paving. It is essential that these construction specialists: (1) are adequately informed about the initial temperature distribution of the asphalt layer – an essential context factor of asphalt compaction; and (2) have the possibility to improve their knowledge by reflecting on the already-conducted and alternative compaction strategies. Both t...

  3. Study on Process for Manufacturing Heavy Traffic Asphalt from Gudong Crude

    Institute of Scientific and Technical Information of China (English)

    Wang Zijun; Long Jun; She Yucheng

    2004-01-01

    The Gudong crude from Gudao oil-bearing region in the Shengli oilfield was used as the target for studying the process of manufacturing heavy traffic road asphalt. The heavy traffic road asphalt products can be made from Gudong crude through blending residuum from mild thermal conversion of vacuum resid with extract, blending the deoiled asphalt from VR propane deasphalting with vacuum resid and the extract, and blending of oxidizedhard asphalt originated from VR with the extract.

  4. Research on the relationship between water stability and aggregate gradation of asphalt pavement

    OpenAIRE

    Zhao Bing; Zhao Bo

    2015-01-01

    In the early destruction of asphalt pavement, water damage is the most major form.In this paper, experimental study was conducted on the composition of asphalt concrete,Marshall specimens were made in different types of aggregate gradation with the same kind of asphalt. Water immersion tests were conducted in order to analysis the relationship between the water stability and aggregate gradation of asphalt pavement.

  5. TECHNOLOGY OF DISPERSED REINFORCEMENT OF ASPHALT CONCRETE MIXTURES WITH CHRYSOTILE FIBRES

    OpenAIRE

    S. I. Buldakov; A. Yu. Dedyukhin

    2010-01-01

    Problem statement. The issues of technology of preparation of dispersed rein-forced asphalt concrete mixtures are still not clearly understood. Available tech-nologies of dispersed reinforcement involve application of granulated additives, which permits the quality of asphalt concrete mixtures to be improved and, there-fore, it will result in increasing life expectancy of asphalt concrete pavements.Results and conclusions. The ways of improvement of quality and durability of asphalt-concrete ...

  6. Stone Matrix Asphalt (SMA is a gap-graded mix that is gaining popularity worldwide. Generally, gap graded mixes are thought to be weak in fatigue resistance. In this study, cellulose fibers were pre-blended in PG64-22 binder with fiber proportions of 0.2%, 0.4%, 0.6%, 0.8% and 1.0% by weight of aggregates. The fiber-modified binder showed improved rheological properties and showed that the PG64-22 binder can be modified and raised to PG70-22 grade. The cellulose oil palm fiber (COPF was found to improve the diameteral fatigue performance of SMA design mix. The fatigue life increased to a maximum at a fiber content of about 0.6%, whilst the tensile stress and stiffness also showed a similar trend in performance. The initial strains of the mix were lowest at a fiber content of 0.6%.

    Directory of Open Access Journals (Sweden)

    Ratnasamy Muniandy

    2006-01-01

    Full Text Available Stone Matrix Asphalt (SMA is a gap-graded mix that is gaining popularity worldwide. Generally, gap graded mixes are thought to be weak in fatigue resistance. In this study, cellulose fibers were pre-blended in PG64-22 binder with fiber proportions of 0.2%, 0.4%, 0.6%, 0.8% and 1.0% by weight of aggregates. The fiber-modified binder showed improved rheological properties and showed that the PG64-22 binder can be modified and raised to PG70-22 grade. The cellulose oil palm fiber (COPF was found to improve the diameteral fatigue performance of SMA design mix. The fatigue life increased to a maximum at a fiber content of about 0.6%, whilst the tensile stress and stiffness also showed a similar trend in performance. The initial strains of the mix were lowest at a fiber content of 0.6%.

  7. On the representative volume element of asphalt concrete at low temperature

    Science.gov (United States)

    Marasteanu, Mihai; Cannone Falchetto, Augusto; Velasquez, Raul; Le, Jia-Liang

    2016-08-01

    The feasibility of characterizing asphalt mixtures' rheological and failure properties at low temperatures by means of the Bending Beam Rheometer (BBR) is investigated in this paper. The main issue is the use of thin beams of asphalt mixture in experimental procedures that may not capture the true behavior of the material used to construct an asphalt pavement.

  8. Survey of microbial degradation of asphalts with notes on relationship to nuclear waste management

    International Nuclear Information System (INIS)

    A survey has been made of the microbial degradation of asphalts. Topics covered include chemical and physical properties of asphalts, their chemical stability, methods of demonstrating their microbial degradation, and environmental extremes for microbial activity based on existing literature. Specific concerns for the use of asphalt in nuclear waste management, plus potential effects and consequences thereof are discussed. 82 references

  9. Survey of microbial degradation of asphalts with notes on relationship to nuclear waste management

    Energy Technology Data Exchange (ETDEWEB)

    ZoBell, C.E.; Molecke, M.A.

    1978-12-01

    A survey has been made of the microbial degradation of asphalts. Topics covered include chemical and physical properties of asphalts, their chemical stability, methods of demonstrating their microbial degradation, and environmental extremes for microbial activity based on existing literature. Specific concerns for the use of asphalt in nuclear waste management, plus potential effects and consequences thereof are discussed. 82 references.

  10. ASPHALT FOR OFF-STREET PAVING AND PLAY AREAS, 3RD EDITION.

    Science.gov (United States)

    Asphalt Inst., College Park, MD.

    THIS PAMPHLET DISCUSSES THE ALTERNATIVE METHODS, APPLICATIONS, AND TECHNICAL CONSIDERATIONS FOR OFF-STREET PAVING AND PLAY AREAS. OFF-STREET PAVING INCLUDES--(1) ASPHALT-PAVED PARKING AREAS, (2) ROOF DECK PARKING AREAS, (3) ASPHALT-PAVED DRIVEWAYS, (4) ASPHALT-PAVED SERVICE STATION LOTS, AND (5) SIDEWALKS. THE DISCUSSION OF PLAY AREAS…

  11. Specifications and Construction Methods for Asphalt Concrete and Other Plant-Mix Types, 3rd Edition.

    Science.gov (United States)

    Asphalt Inst., College Park, MD.

    The purpose of this publication is to assist engineers in the analysis, design and control of paving projects that use asphalt concrete and other asphalt plant-mixes. The scope of this new third edition has been enlarged, and changes necessitated by advances in asphalt technology have been incorporated. Chapters I and II and Appendices A and B…

  12. Preparation and Performance of Asphalt Compound Modified with Waste Crumb Rubber and Waste Polyethylene

    Directory of Open Access Journals (Sweden)

    Yuqiao Yang

    2016-01-01

    Full Text Available Three kinds of modified asphalt were prepared by adding waste crumb rubber (WCR, waste polyethylene (WPE, and WCR/WPE to base asphalt, respectively. The influence of different doses on the performance of modified asphalt, such as 25°C penetration, softening point, 5°C ductility, and 135°C, 165°C viscosity, was studied, and the modification mechanism of modified asphalt was discussed through the fluorescence microscope. As the waterproofing materials, the waterproofness of WCR/WPE compound modified asphalt was tested. The results show that the WPE modified asphalt has excellent resistance to high temperature and WCR modified asphalt has good low temperature resistance. The resistance to deformation ability of WPE modified asphalt is better than that of the WCR modified asphalt. The 135°C viscosity of compound modified asphalt is better than that of WPE and WCR modified asphalt. In addition, the waterproofness of compound modified asphalt using waterproofing materials is better than that of common waterproofing materials.

  13. Image analysis of aggregate,mastic and air void phases for asphalt mixture%Image analysis of aggregate, mastic and air void phases for asphalt mixture

    Institute of Scientific and Technical Information of China (English)

    ADHIKARI Sanjeev; YOU Zhan-ping; HAO Pei-wen; WANG Hai-nian

    2013-01-01

    The shape characterization and spatial distribution of aggregate,mastic and air void phases for asphalt mixture were analyzed.Three air void percentage asphalt mixtures,4%,7% and 8%,respectively,were cut into cross sections and polished.X-ray scanning microscope was used to capture aggregate,mastic,air void phase by the image.The average of polygon diameter was chosen as a threshold to determine which aggregates would be retained on a given sieve.The aggregate morphological image from scanned image was utilized by digital image processing method to calculate the gradation of aggregate and simulate the real gradation.Analysis result shows that the air void of asphalt mixture has influence on the correlation between calculation gradation and actual gradation.When comparing 4.75 mm sieve size of 4%,7% and 8% air void asphalt mixtures,7% air void asphalt mixture has 55% higher than actual size gradation,8% air void asphalt mixture has 8% higher than actual size gradation,and 4% air void asphalt mixture has 3.71% lower than actual size gradation.4% air void asphalt mixture has the best correlation between calculation gradation and actual gradation comparing to other specimens.The air void percentage of asphalt mixture has no obvious influence on the air void orientation,and three asphalt mixtures show the similar air orientation along the same direction.4 tabs,7 figs,17 refs.

  14. Asphalt mounds and associated biota on the Angolan margin

    Science.gov (United States)

    Jones, Daniel O. B.; Walls, Anne; Clare, Michael; Fiske, Mike S.; Weiland, Richard J.; O'Brien, Robert; Touzel, Daniel F.

    2014-12-01

    Release of hydrocarbons from sediments is important in increasing habitat heterogeneity on deep ocean margins. Heterogeneity arises from variation in abiotic and biotic conditions, including changes in substratum, geochemistry, fluid flow, biological communities and ecological interactions. The seepage of heavy hydrocarbons to the seafloor is less well studied than most other cold seep systems and may lead to the formation of asphalt mounds. These have been described from several regions, particularly the Gulf of Mexico. Here, we describe the structure, potential formation and biology of a large asphalt mound province in Block 31SE Angola. A total of 2254 distinct mound features was identified by side-scan sonar, covering a total area of 3.7 km2 of seafloor. The asphalt mounds took a number of forms from small (<0.5 m diameter; 13% observations) mounds to large extensive (<50 m diameter) structures. Some of the observed mounds were associated with authigenic carbonate and active seepage (living chemosynthetic fauna present in addition to the asphalt). The asphalt mounds are seabed accumulations of heavy hydrocarbons formed from subsurface migration and fractionation of reservoir hydrocarbons primarily through a network of faults. In Angola these processes are controlled by subsurface movement of salt structures. The asphalt mounds were typically densely covered with epifauna (74.5% of mounds imaged had visible epifauna) although individual mounds varied considerably in epifaunal coverage. Of the 49 non-chemosynthetic megafaunal taxa observed, 19 taxa were only found on hard substrata (including asphalt mounds), 2 fish species inhabited the asphalt mounds preferentially and 27 taxa were apparently normal soft-sediment fauna. Antipatharians (3.6±2.3% s.e.) and poriferans (2.6±1.9% s.e.) accounted for the highest mean percentage of the observed cover, with actinarians (0.9±0.4% s.e.) and alcyonaceans (0.4±0.2% s.e.) covering smaller proportions of the area

  15. Use of plastic waste (poly-ethylene terephthalate) in asphalt concrete mixture as aggregate replacement.

    Science.gov (United States)

    Hassani, Abolfazl; Ganjidoust, Hossein; Maghanaki, Amir Abedin

    2005-08-01

    One of the environmental issues in most regions of Iran is the large number of bottles made from poly-ethylene terephthalate (PET) deposited in domestic wastes and landfills. Due to the high volume of these bottles, more than 1 million m3 landfill space is needed for disposal every year. The purpose of this experimental study was to investigate the possibility of using PET waste in asphalt concrete mixes as aggregate replacement (Plastiphalt) to reduce the environmental effects of PET disposal. For this purpose the mechanical properties of plastiphalt mixes were compared with control samples. This study focused on the parameters of Marshall stability, flow, Marshall quotient (stability-to-flow ratio) and density. The waste PET used in this study was in the form of granules of about 3 mm diameter which would replace (by volume) a portion of the mineral coarse aggregates of an equal size (2.36-4.75 mm). In all prepared mixes the determined 6.6% optimum bitumen content was used. In this investigation, five different percentages of coarse aggregate replacement were used. The results showed that the aggregate replacement of 20% by volume with PET granules would result in a reduction of 2.8% in bulk compacted mix density. The value of flow in the plastiphalt mix was lower than that of the control samples. The results also showed that when PET was used as partial aggregate replacement, the corresponding Marshall stability and Marshall quotient were almost the same as for the control samples. According to most of specification requirement, these results introduce an asphalt mix that has properties that makes it suitable for practical use and furthermore, the recycling of PET for asphalt concrete roads helps alleviate an environmental problem and saves energy. PMID:16200982

  16. Modeling of change in asphalt concrete dynamic modulus

    Directory of Open Access Journals (Sweden)

    A.M. Kirillov

    2015-03-01

    Full Text Available Historically, since the 1930s, deformation and power criteria were defined by methods of calculation of non-rigid road clothes (the deformation modulus, the California bearing ratio, the dynamic modulus. For almost a centenary history considerable statistical changes of the specified indicators in road layers were collected. However, the physical essence of these changes and their regularity still remain unknown. Over the last decade in the field of auto roads the use of energy criteria has been more universal in comparison with the strength and deformation. These criteria bear in itself a predictive function, allow not only estimating integrally and complexly the pavement functional condition, but also managing this state during operation. Despite this fact, in today’s regulatory documents one of the main characteristics of asphalt concrete is still the deformation indicator – dynamic modulus. At the same time, now there is no reliable approach that would make it possible to define change of dynamic modulus of asphalt concrete in operation, so this task is still urgent. Moreover, there are no accurate dependences of ratio change between static and dynamic modules of asphalt concrete during operation. Change of dynamic modulus as private indicator can be used at calculation of energy functions variation. In this paper the authors made an attempt to simulate changes of dynamic modulus of asphalt concrete when loading and analyzed the suggested viscoelastic model. New results, in particular analytical dependences, can form the basis of new regulatory documents for asphalt concrete pavement construction.

  17. Recovery and reuse of asphalt roofing waste. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Desai, S.; Graziano, G.; Shepherd, P.

    1984-02-02

    Burning of asphalt roofing waste as a fuel and incorporating asphalt roofing waste in bituminous paving were identified as the two outstanding resource recovery concepts out of ten studied. Four additional concepts might be worth considering under different market or technical circumstances. Another four concepts were rated as worth no further consideration at this time. This study of the recovery of the resource represented in asphalt roofing waste has identified the sources and quantities of roofing waste. About six million cubic yards of scrap roofing are generated annually in the United States, about 94% from removal of old roofing at the job site and the remainder from roofing material production at factories. Waste disposal is a growing problem for manufacturers and contractors. Nearly all roofing waste is hauled to landfills at a considerable expense to roofing contractors and manufacturers. Recovery of the roofing waste resource should require only a modest economic incentive. The asphalt contained in roofing waste represents an energy resource of more than 7 x 10/sup 13/ Btu/year. Another 1 x 10/sup 13/ Btu/year may be contained in field-applied asphalt on commercial building roofs. The two concepts recommended by this study appear to offer the broadest applicability, the most favorable economics, and the highest potential for near-term implementation to reuse this resource.

  18. European experience with asphalt packaging of radioactive wastes

    International Nuclear Information System (INIS)

    In Europe, the use of asphalt is synonymous with volume reduction of low and medium level radioactive waste. It started at Marcoule, France in the early 1960's and soon was adopted by Karlsruhe in West Germany, Eurochemic in Belgium, and in other countries. The use of an asphalt (or bitumen) binder, or immobilizing agent, in the VRS (Volume Reduction and Solidification) process proved to be beneficial in many ways. At Karlsruhe, for example, the VRS asphalt system replaced a cement system (non-volume reducing) and resulted in two drums of solidified waste versus ten with cement. This process reduced the transportation problem considerably. Asphalt is an inert, waterproof material and provides significantly improved package integrity under all conditions of on-site storage, transportation, and burial. The asphalt VRS system provides considerable cost savings, particularly for the recurring items such as binder, containers, transportation, and burial. These annual savings may approach $500,000 annually for a 1000 MWe nuclear plant. End product advantages include higher resistance to leaching and other environmental impacts, as well as less internal corrosion of the drums

  19. Determination of Rheological Properties of Bio Mastic Asphalt

    Directory of Open Access Journals (Sweden)

    R. Muniandy

    2008-01-01

    Full Text Available Due to the high oil prices the price of asphalt binder has increased tremendously. This scenario has warranted demand for higher viscosity cheaper asphalt for pavement construction. A study was conducted to take advantage of the Empty Fruit Bunch (EFB of Date and Oil Palm trees (which are considered as waste to produce cellulose fiber to be used as additives in the asphalt binder. If these EFB's could be beneficially utilized in any application, it would reduce the load on the nation's landfills and at the same time reducing the cost of road construction. A total of 11 blends were prepared that consisted of 5 blends with date palm fiber, 5 blends with oil palm fiber and one control sample that contained no fibers. The samples were evaluated using Dynamic Shear Rheometer (DSR equipment in accordance with the superpave Strategic Highway Research Program (SHRP requirements. The neat asphalt binders (Unaged, Rolling Thin Film Oven (RTFO aged and Pressure Ageing Vessel (PAV samples were then measured for phase angle, shear strain and complex shear modulus and then evaluated in accordance with SHRP requirements. The results indicated that the fibers enhanced the rheological performance of Bio Mastic Asphalt (BMA blends. The control sample which was categorized as PG58 was enhanced to PG76 with 0.375% date palm fiber. The oil palm has also improved the blend up to PG70 with 0.3% oil palm fiber.

  20. Aging test results of an asphalt membrane liner

    International Nuclear Information System (INIS)

    The objective of the asphalt aging study described in this report was to determine the expected performance lifetime of a catalytically airblown asphalt membrane as a seepage barrier for inactive uranium mill tailings. The study, conducted by Pacific Northwest Laboratory for the Department of Energy's Uranium Mill Tailings Remedial Action Program, showed through chemical compatibility tests that the asphalt membrane is well suited for this purpose. The chemical compatibility tests were designed to accelerate the aging reactions in the asphalt and to determine the accelerated aging effect. Higher temperatures and oxygen concentrations proved to be effective acceleration parameters. By infrared spectral analysis, the asphalt was determined to have undergone 7 years of equivalent aging in a 3-month period when exposed to 400C and 1.7 atm oxygen pressure. However, the extent of aging was limited to a maximum penetration of 0.5% of the total liner thickness. It was concluded that the liner could be expected to be effective as a seepage barrier for at least 1000 years before the entire thickness of the liner would be degraded

  1. Hanford Protective Barriers Program asphalt barrier studies -- FY 1988

    International Nuclear Information System (INIS)

    The Hanford Protective Barrier (HPB) Program is evaluating alternative barriers to provide a means of meeting stringent water infiltration requirements. One type of alternative barrier being considered is an asphalt-based layer, 1.3 to 15 cm thick, which has been shown to be very effective as a barrier for radon gas and, hence, should be equally effective as a barrier for the larger molecules of water. Fiscal Year 1988 studies focused on the selection and formulation of the most promising asphalt materials for further testing in small-tube lysimeters. Results of laboratory-scale formulation and hydraulic conductivity tests led to the selection of a rubberized asphalt material and an admixture of 24 wt% asphalt emulsion and concrete sand as the two barriers for lysimeter testing. Eight lysimeters, four each containing the two asphalt treatments, were installed in the Small Tube Lysimeter Facility on the Hanford Site. The lysimeter tests allow the performance of these barrier formulations to be evaluated under more natural environmental conditions

  2. STATE OF TRANSPORT PROCESSES FOR REPAIRING AND ASPHALTING OF ASPHALT ROADS AND WAYS THEIR DEVELOPMENT

    Directory of Open Access Journals (Sweden)

    Nikolaev N. N.

    2015-04-01

    Full Text Available The article explains the importance of the transport process when performing repair jobs of asphalt roads. The scheme of the technological process was drawn up; job steps were identified, while the latter may be characterized by non-productive downtime of transport as well as that one of technological machines. We have analyzed the following steps of the flowchart of the road concrete mix transportation: the preparation of the road concrete mix for transportation, loading, transportation, unloading, laying and packing. The transportation of goods starts at the working site of their production and ends at the site of their consumption. The transportation process is a multistep and multioperational process having the greater diversity of technological, operational and economic operations, which must be correctly organized. It is extremely important to deliver the road concrete mix of coating plant (OP just in time, while avoiding the unproductive idle standing of the equipment, the deterioration of the mixture, as well as performing the job steps at minimum transportation cost savings. The successful combining of the steps of the concept organization of the road concrete mix transportation (coating plant, asphalt laying step, transportation step will improve the performance and will provide the reduction of the job cost. One must perform the coordination of job steps on different road sections using information technologies and communication facility

  3. Production of De-asphalted Oil and Fine Asphalt Particles by Supercritical Extraction

    Institute of Scientific and Technical Information of China (English)

    赵锁奇; 许志明; 王仁安

    2003-01-01

    A continuous three-stage supercritical fluid extraction (SFE) process with a capacity of 1.0kg.h-1 was setup to extract petroleum residue by pentane to obtain more oil for further upgrading. A discharging system integrated to the bottom of the extractor was used to recover solvent as gas while asphalt was obtained as fine particles. The influence of operating conditions on the yield and quality of extracts, i.e., deasphalted oil (DAO) and resin, was studied in the range of temperature 150-220℃, pressure of 4.0-6.0 MPa and the mass ratio of solvent to oil feed (S/O) 2.5-5.0. The particle size distribution, apparent forms and the packing density, which vary with operating pressure, were measured. The particle structures were observed by SEM as well. With the modification to conventional processes, furnace can be eliminated for solvent recovery from asphalt phase, so as to reduce energy consumption.

  4. Triterpane distributions in diapir-related asphalts

    Energy Technology Data Exchange (ETDEWEB)

    Dorronsoro, C.; Garcia, M.R.; Grimalt, J.O. (University of the Basque Country, Donostia (Spain). College of Chemistry)

    1994-01-01

    A gas chromatographic-mass spectrometric study of solvent-soluble extracts from asphalt-rich sediments in a diapir-intruded crude oil reservoir rock has demonstrated the extended biodegradation of the hydrocarbons in the strata in contact with the diapir. The process has led to a sedimentary hydrocarbon composition dominated by unresolved complex mixtures of aliphatic and aromatic hydrocarbons in which two main groups of resolved peaks in the gas chromatograms can be recognized. The dominant group encompasses the compounds preserved in these conditions and is composed of two distributions of hexacyclic hopanoids, a series of C[sub 32]-C[sub 35] 20,32-cyclobishomohopanes and a new series of C[sub 33]-C[sub 35] homologues whose structure is not yet fully elucidated. The second group corresponds to partly transformed aliphatic and aromatic structures, namely series of C[sub 27]-C[sub 30]8,14-seco-hopanes and C[sub 27]-C[sub 31]D-ring aromatic 8,14-seco-hopanes. 26 refs., 8 figs., 2 tabs.

  5. 苯乙烯焦油对橡胶改性沥青性能的影响%RESEARCH OF STYRENE TAR ON PROPERTIES OF RUBBER MODIFIED ASPHALT

    Institute of Scientific and Technical Information of China (English)

    曹萍; 单宝龙; 王雷; 李丹东; 石薇薇; 胡杨

    2012-01-01

    Crumb rubber and styrene tar were used to modify asphalt of Liaohe Oilfield asphalt by high shearing technology. The effect of the amounts of crumb rubber and styrene tar on the performance of the modified asphalt was investigated. Under the following optimal conditions: rubber powder content of 15% and adding styrene tar to asphalt modified with 15% rubber, the styrene tar and rubber powder could be in fully swelling in the asphalt and the performance of the rubber modified asphalt was improved. Experimental results showed that styrene tar can improve the performance of the rubber modified asphalt, with the softening point of 39. 7 ℃, needle penetration degree of 115(0. 1 mm), ductility of 121 cm, reaching the No 140 road asphalt standards. The aging experiments showed that the rubber powders were coalescence and exhalation.%实验以辽河油田生产的沥青为原料,加入橡胶粉和苯乙烯焦油,以高速剪切法制备改性沥青.考察了橡胶粉和苯乙烯焦油对沥青性能的影响,并对改性沥青进行老化实验.确定最佳橡胶粉质量分为15%,并向质量分数为15%橡胶改性沥青中加入苯乙烯焦油,使橡胶粉可在沥青中充分溶胀,提高橡胶沥青的使用性能.实验表明,苯乙烯焦油的加入可提高橡胶改性沥青的性能,此时沥青的软化点可达39.7℃,沥青的针入度可以达11(0.1 mm),延度为121 cm,符合140号道路沥青标准.老化实验表明,改性沥青老化后橡胶粉有聚结和析出.

  6. Asphalt emulsion sealing of uranium mill tailings. 1980 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, J.N.; Koehmstedt, P.L; Esterl, D.J.; Freeman, H.D.; Buelt, J.L.; Nelson, D.A.; Elmore, M.R.

    1981-05-01

    Studies of asphalt emulsion sealants conducted by the Pacific Northwest Laboratory have demonstrated that the sealants are effective in containing radon and other potentially hazardous material within uranium tailings. The laboratory and field studies have further demonstrated that radon exhalation from uranium tailings piles can be reduced by greater than 99% to near background levels. Field tests at the tailings pile in Grand Junction, Colorado, confirmed that an 8-cm admix seal containing 22 wt% asphalt could be effectively applied with a cold-mix paver. Other techniques were successfully tested, including a soil stabilizer and a hot, rubberized asphalt seal that was applied with a distributor truck. After the seals were applied and compacted, overburden was applied over the seal to protect the seal from ultraviolet degradation.

  7. Asphalt emulsion sealing of uranium mill tailings. 1980 annual report

    International Nuclear Information System (INIS)

    Studies of asphalt emulsion sealants conducted by the Pacific Northwest Laboratory have demonstrated that the sealants are effective in containing radon and other potentially hazardous material within uranium tailings. The laboratory and field studies have further demonstrated that radon exhalation from uranium tailings piles can be reduced by greater than 99% to near background levels. Field tests at the tailings pile in Grand Junction, Colorado, confirmed that an 8-cm admix seal containing 22 wt% asphalt could be effectively applied with a cold-mix paver. Other techniques were successfully tested, including a soil stabilizer and a hot, rubberized asphalt seal that was applied with a distributor truck. After the seals were applied and compacted, overburden was applied over the seal to protect the seal from ultraviolet degradation

  8. EVALUATING AND IMPROVING THE PERFORMANCE OF COLD ASPHALT EMULSION MIXES

    Directory of Open Access Journals (Sweden)

    I Nyoman Arya Thanaya

    2007-01-01

    Full Text Available This paper describes investigation on the performances of cold asphalt emulsion mixes (CAEMs. The type of emulsion used was a cationic asphalt emulsion. The investigation was carried out at Leeds University, United Kingdom (UK. The objective of the experiments was to evaluate and to improve the performances of cold mixes and compared with hot mixes. For optimising the performances of the cold mixes, a target porosity of five to ten percent and indirect tensile stiffness modulus (ITSM value of 2000 MPa was selected, suitable for low to medium trafficked roads. A simplified mix design procedure was used for producing the cold mixes. It was found that when properly designed, at full curing conditions, the stiffness (ITSM of CAEMs were found to be very comparable to those of hot mixes. Test results also show that the addition of cement in the amount of one to two percent by mass of aggregates significantly improved the mechanical performance of cold asphalt mixes.

  9. Design of a sensor for asphalt pavement pressure field measurements

    Science.gov (United States)

    Liu, Hongyue; Liang, Dakai; Han, Xiaolin; Wang, Xiaogang

    2013-06-01

    From the sensitivity of the FBG center wavelength changing with strain changes on the surface, the design of a FBG strain-based asphalt pavement pressure sensor is described by designing a special FBG asphalt box-film packaging structure. The compactness and simplicity of the device are achieved by using the corresponding package obtained from common available asphalt. Numerical analysis and experimental results show that the response of the sensor has good regularity for a wide range of travel (0MPa to 5.3312MPa). In the load range, the FBG center wavelength increases from 1548.264nm to 1548.346nm which shows a good correspondence with loads. Linearity, travel and sensitivity are experimentally determined by different packaging parameters. A design chart that includes the travel (0MPa to 5.3312MPa) and the sensitivity (15.3812pm/MPa) is finally proposed.

  10. Hanford Permanent Isolation Barrier Program: Asphalt technology test plan

    International Nuclear Information System (INIS)

    The Hanford Permanent Isolation Barriers use engineered layers of natural materials to create an integrated structure with backup protective features. The objective of current designs is to develop a maintenance-free permanent barrier that isolates wastes for a minimum of 1000 years by limiting water drainage to near-zero amounts. Asphalt is being used as an impermeable water diversion layer to provide a redundant layer within the overall barrier design. Data on asphalt barrier properties in a buried environment are not available for the required 100-year time frame. The purpose of this test plan is to outline the activities planned to obtain data with which to estimate performance of the asphalt layers

  11. Application of asphalt emulsion seals to uranium mill tailings

    International Nuclear Information System (INIS)

    Studies of asphalt emulsion sealants have demonstrated that the sealants are effective in containing radon and other potentially hazardous material within uranium tailings. The laboratory and field studies have further demonstrated that radon exhalation from uranium tailings piles can be reduced by greater than 99% to less than background levels. Field tests at the tailings pile in Grand Junction, Colorado confirmed that an 8-cm admix seal containing 22 wt % asphalt could be effectively applied with a cold-mix paver. Other techniques were successfully tested, including a soil stabilizer and a hot, rubberized asphalt seal that was applied with a distributor truck. After the seals were applied and conpacted, overburden was applied over the seal to protect the seal from ultraviolet degradation. 14 figures

  12. Investigation of Asphalt Mixture Creep Behavior Using Thin Beam Specimens

    International Nuclear Information System (INIS)

    The asphalt pavement layer consists of two or more lifts of compacted asphalt mixture; the top of the layer is also exposed to aging, a factor that significantly affects the mixture properties. The current testing specifications use rather thick specimens that cannot be used to investigate the gradual change in properties with pavement depth. This paper investigates the feasibility of using the 3-point bending test with thin asphalt mixture beams (127x12.7x6.35 mm) to determine the low-temperature creep compliance of the mixtures. Several theoretical and semi-empirical models, from the theory of composites, are reviewed and evaluated using numerical and experimental data. Preliminary results show that this method can be used for low-temperature mixture characterization but several crucial factors need further inspection and interpretation

  13. Deformation Parameters and Fatigue of the Recycled Asphalt Mixtures

    Science.gov (United States)

    Šrámek, Juraj

    2015-12-01

    The deformational properties of asphalt mixtures measured by dynamic methods and fatigue allow a design the road to suit the expected traffic load. Quality of mixtures is also expressed by the resistance to permanent deformation. Complex modulus of stiffness and fatigue can reliably characterize the proposed mixture of asphalt pavement. The complex modulus (E*) measurement of asphalt mixtures are carried out in laboratory of Department of Construction Management at University of Žilina by two-point bending test method on trapezoid-shaped samples. Today, the fatigue is verified on trapezoid-shaped samples and is assessed by proportional strain at 1 million cycles (ɛ6). The test equipment and software is used to evaluate fatigue and deformation characteristics.

  14. Deformation Parameters and Fatigue of the Recycled Asphalt Mixtures

    Directory of Open Access Journals (Sweden)

    Šrámek Juraj

    2015-12-01

    Full Text Available The deformational properties of asphalt mixtures measured by dynamic methods and fatigue allow a design the road to suit the expected traffic load. Quality of mixtures is also expressed by the resistance to permanent deformation. Complex modulus of stiffness and fatigue can reliably characterize the proposed mixture of asphalt pavement. The complex modulus (E* measurement of asphalt mixtures are carried out in laboratory of Department of Construction Management at University of Žilina by two-point bending test method on trapezoid-shaped samples. Today, the fatigue is verified on trapezoid-shaped samples and is assessed by proportional strain at 1 million cycles (ε6. The test equipment and software is used to evaluate fatigue and deformation characteristics.

  15. Asphalt emulsion sealing of uranium mill tailings. 1979 annual report

    Energy Technology Data Exchange (ETDEWEB)

    Hartley, J.N.; Koehmstedt, P.L.; Esterl, D.J.; Freeman, H.D.

    1980-06-01

    Uranium mill tailings are a source of low-level radiation and radioactive materials that may be released into the environment. Stabilization or disposal of these tailings in a safe and environmentally sound way is necessary to minimize radon exhalation and other radioactive releases. One of the most promising concepts for stabilizing uranium tailings is being investigated at the Pacific Northwest Laboratory: the use of asphalt emulsion to contain radon and other potentially hazardous materials in uranium tailings. Results of these studies indicate that radon flux from uranium tailings can be reduced by greater than 99% by covering the tailings with an asphalt emulsion that is poured on or sprayed on (3.0 to 7.0 mm thick), or mixed with some of the tailings and compacted to form an admixture seal (2.5 to 15.2 cm) containing 18 wt % residual asphalt.

  16. Asphalt emulsion sealing of uranium mill tailings. 1979 annual report

    International Nuclear Information System (INIS)

    Uranium mill tailings are a source of low-level radiation and radioactive materials that may be released into the environment. Stabilization or disposal of these tailings in a safe and environmentally sound way is necessary to minimize radon exhalation and other radioactive releases. One of the most promising concepts for stabilizing uranium tailings is being investigated at the Pacific Northwest Laboratory: the use of asphalt emulsion to contain radon and other potentially hazardous materials in uranium tailings. Results of these studies indicate that radon flux from uranium tailings can be reduced by greater than 99% by covering the tailings with an asphalt emulsion that is poured on or sprayed on (3.0 to 7.0 mm thick), or mixed with some of the tailings and compacted to form an admixture seal (2.5 to 15.2 cm) containing 18 wt % residual asphalt

  17. Hanford Permanent Isolation Barrier Program: Asphalt technology test plan

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Romine, R.A.

    1994-05-01

    The Hanford Permanent Isolation Barriers use engineered layers of natural materials to create an integrated structure with backup protective features. The objective of current designs is to develop a maintenance-free permanent barrier that isolates wastes for a minimum of 1000 years by limiting water drainage to near-zero amounts. Asphalt is being used as an impermeable water diversion layer to provide a redundant layer within the overall barrier design. Data on asphalt barrier properties in a buried environment are not available for the required 100-year time frame. The purpose of this test plan is to outline the activities planned to obtain data with which to estimate performance of the asphalt layers.

  18. Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

    OpenAIRE

    Yongjoo Kim; Tae-Soon Park

    2013-01-01

    This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA) mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of...

  19. Reduction in radiation exposure and volume using asphalt solidification

    International Nuclear Information System (INIS)

    The solidification of liquid and solid radioactive wastes from nuclear power plants with an extruder-evaporator using an asphalt binder minimizes both volume and radiation exposure. The automatic evaporation of water in liquid radwastes prior to incorporation into asphalt reduces the volume to be transported and disposed. In turn, the numbers of drums requiring handling is reduced 5 to 10 times thereby lessening the chances for radiation exposure. Also, the extruder-evaporator is self-shielded and contains only about one gallon of the radwaste. Dose rates at the surface of the equipment and filled containers from commercially operating systems for the past 10 years in Europe are given

  20. SYSTEM FOR CONTROLLING ELECTRIC DRIVE OF ASPHALT CONCRETE MIXING PLANT

    Directory of Open Access Journals (Sweden)

    A. S. Surmak

    2005-01-01

    Full Text Available It is proposed to evaluate quality of asphalt concrete mixture through definition of current component variable of a drive motor and measurement of its derivative sign. In order to carry out final determination of mixture uniformity a transducer on the basis of a nuclear magnetic resonance is applied. Block diagram of the system is presented and algorithm of its operation is given in the paper. In addition to improvement of the finished product quality the application of the system makes it possible to reduce bitumen consumption used for production of asphalt concrete.

  1. Final environmental and regulatory assessment of using asphalt as a sealant in mine shafts

    International Nuclear Information System (INIS)

    This report discusses the properties of asphalt, the current regulatory status governing asphalt and future regulatory implications which may be pertinent in using asphalt as a waterproof shaft sealant. An understanding of the inherent organic composition of asphalt, an increase in the number of health and environmental research publications conducted on asphalt and an examination of the apparent trend of regulatory agencies toward more stringent environmental regulation governing the use of organic materials suggests asphalt could become regulated at a future time. This would only occur, however, if asphalt was found to conform to the present regulatory definitions of pollutants, contaminants or hazardous substances or if asphalt was included on a regulated substance list. In this regard, the study points out that asphalt contains very low levels of hazardous poly-nuclear aromatics (PNA's). These levels are significantly lower than the levels present in coal tars, a substance known to contain high levels of hazardous PNA's. Asphalt, however, has the inherent potential of producing higher concentrations of PNA's if the adverse condition of cracking should occur during the refinery production stage or on-site preparation of the asphalt. Also, unless existing control technology is applied, emission levels of sulfur dioxide, carbon monoxide, particulates and volatile organic carbons from the on-site preparation facilities could approach the permissible health standard levels of EPA. The study indicates, however, that available literature is limited on these issues

  2. Modelling and Laboratory Studies on the Adhesion Fatigue Performance for Thin-Film Asphalt and Aggregate System

    OpenAIRE

    Dongsheng Wang; Junyan Yi; Decheng Feng

    2014-01-01

    Adhesion between asphalt and aggregate plays an important role in the performance of asphalt mixtures. A low-frequency adhesion fatigue test was proposed in this paper to study the effect of environment on the asphalt-aggregate adhesion system. The stress-based fatigue model had been utilized to describe the fatigue behavior of thin-film asphalt and aggregate system. The factors influencing the adhesion fatigue performance were also investigated. Experiment results show that asphalt has more ...

  3. Influence Of The Powder/Asphalt Ratio On The High Stress Responses Of Crumb Rubber Modified Asphalt Mortars

    Directory of Open Access Journals (Sweden)

    Ma Tengfei

    2016-04-01

    Full Text Available In order to study different powder/asphalt ratios effect on nonlinear viscoelastic responses of mortar, this paper choose limestone as the filler, and powder/asphalt ratio is 0.2,0.4,0.6,and 0.8.The tests were conducted using a Dynamic Shear Rheometer to perform multiple stress creep recovery (MSCR tests.The test results show that,with the increase of powder/asphalt ratio irrecoverable creep compliance(Jnr value of the mortar , decrease gradually, and the amplitude is larger.High temperature performance of the mortar are improve obviously.Using environmental scanning electron microscopy to scan those mortars,it analyzed the improvement of mortar from the microcosmic mechanism.

  4. Criteria for asphalt-rubber concrete in civil airport pavements: Mixture design

    Science.gov (United States)

    Roberts, F. L.; Lytton, R. L.; Hoyt, D.

    1986-07-01

    A mixture design procedure is developed to allow the use of asphalt-rubber binders in concrete for flexible airport pavement. The asphalt-rubber is produced by reacting asphalt with ground, scrap tire rubber to produce the binder for the asphalt-rubber concrete. Procedures for laboratory preparation of alsphalt-rubber binders using an equipment setup that was found by researchers to produce laboratory binders with similar properties to field processes are included. The rubber-asphalt concrete mixture design procedure includes adjustments to the aggregate gradation to permit space for the rubber particles in the asphalt-rubber binder as well as suggested mixing and compaction temperatures, and compaction efforts. While the procedure was used in the laboratory to successfully produce asphalt-rubber concrete mixtures, it should be evaluated in the field to ensure that consistent results can be achieved in a production environment.

  5. The Research on Improvement of Low Temperature Stability for Diatomite Modified Asphalt Mixture with PE Particles

    Directory of Open Access Journals (Sweden)

    HU Qiusheng

    2015-01-01

    Full Text Available In light of the lake of low temperature stability for diatomaceous which used as asphalt modifier.Stat the research with the diatomite produced at Jilin Changbai, using the way of low temperature bending test to evaluate the PE and diatomite composite modified asphalt mixture’s low temperature crack resistance performance. The results showed that after the diatomite and PE composite modified asphalt mixture has the best advantage of anti-cracking performance under low-temperature environment,which is better than PE modified asphalt mixture and the matrix asphalt mixture. As a result,asphalt mixture being composite modified by diatomite and PE could significantly improve asphalt mixture’s low temperature stable performance.

  6. Numerical simulation on the thermal response of heat-conducting asphalt pavements

    International Nuclear Information System (INIS)

    Using asphalt pavements as a solar collector is a subject of current interest all over the world because the sun provides a cheap and abundant source of clean and renewable energy, which can be captured by black asphalt pavements. A heat-conducting device is designed to absorb energy from the sun. In order to validate what parameters are critical in the asphalt collector, a finite element model is developed to predict the thermal response of the heat-conducting device compared to the conventional asphalt mixture. Some factors that may affect the asphalt pavement collector are considered, including the coefficient of heat conductivity of the asphalt pavement, the distance between pipes with the medium, water, and the pipe's diameter. Ultimately, the finite element model can provide pavement engineers with an efficient computational tool that can be a guide to the conductive asphalt solar collector's experiment in the laboratory.

  7. Influence of Subgrade and Unbound Granular Layers Stiffness on Fatigue Life of Hot Mix Asphalts - HMA

    Directory of Open Access Journals (Sweden)

    Hugo A. Rondón-Quintana

    2013-11-01

    Full Text Available The mainly factors studied to predict fatigue life of hot mix asphalt-HMA in flexible pavements are the loading effect, type of test, compaction methods, design parameters of HMA (e.g., particle size and size distribution curve, fine content, type of bitumen and the variables associated with the environment (mainly moisture, temperature, aging. This study evaluated through a computer simulation, the influence of the granular layers and subgrade on the fatigue life of asphalt layers in flexible pavement structures. Mechanics parameters of granular layers of subgrade, base and subbase were obtained using the mathematical equations currently used for this purpose in the world. The emphasis of the study was the city of Bogotá, where the average annual temperature is 14°C and soils predominantly clay, generally experience CBR magnitudes between 1% and 4%. General conclusion: stiffness of the granular layers and subgrade significantly affect the fatigue resistance of HMA mixtures. Likewise, the use of different equations reported in reference literature in order to characterize granular layers may vary the fatigue life between 4.6 and 48.5 times, varying the thickness of the pavement layers in the design.

  8. Anhydrides-Cured Bimodal Rubber-Like Epoxy Asphalt Composites: From Thermosetting to Quasi-Thermosetting

    Directory of Open Access Journals (Sweden)

    Yang Kang

    2016-03-01

    Full Text Available The present engineering practices show the potential that epoxy asphalt composites (EACs would be a better choice to obtain long life for busy roads. To understand the service performance–related thermorheological properties of prepared bimodal anhydrides-cured rubber-like EACs (REACs, a direct tensile tester, dynamic shear rheometer and mathematical model were used. Tensile tests demonstrate that all the REACs reported here are more flexible than previously reported anhydrides-cured REACs at both 20 and 0 °C. The better flexibility is attributed to the change of bimodal networks, in which cross-linked short chains decreased and cross-linked long chains increased, relatively. Strain sweeps show that all the REACs have linear viscoelastic (LVE properties when their strains are smaller than 1.0% from −35 to 120 °C. Temperature sweeps illustrate that the thermorheological properties of REACs evolve from thermosetting to quasi-thermosetting with asphalt content, and all the REACs retain solid state and show elastic properties in the experimental temperature range. A Cole–Cole plot and Black diagram indicate that all the REACs are thermorheologically simple materials, and the master curves were constructed and well-fitted by the Generalized Logistic Sigmoidal models. This research provides a facile approach to tune the thermorheological properties of the REACs, and the cheaper quasi-thermosetting REAC facilitates their advanced applications.

  9. Dynamic Properties and Fatigue Life of Stone Mastic Asphalt Mixtures Reinforced with Waste Tyre Rubber

    Directory of Open Access Journals (Sweden)

    Nuha Salim Mashaan

    2013-01-01

    Full Text Available Today, virgin polymer modified asphalt mixes are comparatively more expensive for road pavement. One way to reduce the expense of such construction and to make it more convenient is the application of inexpensive polymer, such as waste polymer. The primary aim of this study was to investigate the effect of adding waste tyre rubber (crumb rubber modifier (CRM on the stiffness and fatigue properties of stone mastic asphalt (SMA mixtures. Various percentages of waste CRM with size of 0.60 mm were added to SMA mixtures. Indirect tensile stiffness modulus test was conducted at temperatures of 5, 25, and 40°C. Indirect tensile fatigue test was conducted at three different stress levels (2000, 2500, and 3000 N. The results show that the stiffness modulus of reinforced SMA samples containing various contents of CRM is significantly high in comparison with that of nonreinforced samples, and the stiffness modulus of reinforced samples is in fact less severely affected by the increased temperature compared to the nonreinforced samples. Further, the results show that CRM reinforced SMA mixtures exhibit significantly higher fatigue lives compared to the nonreinforced mixtures help in and promotion of sustainable technology by recycling of waste materials in much economical and environmental-friendly manner.

  10. Background of superpave asphalt mixture design and analysis. National asphalt training center demonstration project 101. Final report, December 1992-November 1994

    Energy Technology Data Exchange (ETDEWEB)

    McGennis, R.B.; Anderson, R.M.; Kennedy, T.W.; Solaimanian, M.

    1995-02-01

    The manual represents the first formal training document that embodies the complete series of SUPERPAVE asphalt mixture design and analysis test equipment and procedures. These tests and procedures represent the results of the SHRP 5-year research effort to investigate and improve asphalt cement technology. This manual was developed under the FHWA`s National Asphalt Training Center. Students attending the center utilize this manual to obtain a better understanding of the underlying theory behind asphalt mixture design and analysis, as well as how to perform each of the new procedures.

  11. Progresses in irradiating SBS for road asphalt applications

    International Nuclear Information System (INIS)

    Technical developments at SINAP to improve properties of SBS, a styrene-butadiene- styrene copolymer, for road asphalt applications are reviewed. In an attempt to better solve problems related to undesirable compatibility of SBS to asphalt components, we proposed a new method to modify the SBS molecular chains with ionizing radiations through radiation graft copolymerization and radiation crosslinking. Grafting a monomer with polar functional groups onto SBS molecules improves compatibility of SBS to polar components of asphalt, hence enhanced storage stability of the polymer modified asphalt (PMA), while crosslinks of SBS molecular chains endues increased physical properties to the PMA. Mechanisms of the radiation effects were studied with a series of SBS samples irradiated by 60Co γ-rays or electron beams. The PMA and macadam-blended PMA samples showed higher performance than the control, i.e. SBS-modified asphalt by conventional approaches. The results can be summarized as follows. 1. The grafted SBS enhances thermostability of saturates and aromatics, the two asphalt components that exhibit the biggest SBS-swelling effect. The resins of asphalt, however, can hardly be absorbed by SBS, and the SBS is in a phase-separation status with the resins. Therefore, it is crucial to strengthen reactions between SBS and the resins to obtain stable and high quality PMA. 2. SBS molecular chains can be crosslinked with irradiation of a few tens of kGy. The crosslinking effect was evidenced by increased molecular weight of SBS and wider distribution of the molecular weight in GPC measurement of the irradiated SBS samples, and by decreased activation energy of viscosity in rheological measurement, in which the storage modulus G' increased and the loss modulus G' declined with increasing doses, indicating a larger elastic component and smaller viscous component in the irradiated SBS. Correspondingly, temperature sensitivity of the irradiated SBS reduced. Blended with SBS

  12. Analysis of Adhesive Characteristics of Asphalt Based on Atomic Force Microscopy and Molecular Dynamics Simulation.

    Science.gov (United States)

    Xu, Meng; Yi, Junyan; Feng, Decheng; Huang, Yudong; Wang, Dongsheng

    2016-05-18

    Asphalt binder is a very important building material in infrastructure construction; it is commonly mixed with mineral aggregate and used to produce asphalt concrete. Owing to the large differences in physical and chemical properties between asphalt and aggregate, adhesive bonds play an important role in determining the performance of asphalt concrete. Although many types of adhesive bonding mechanisms have been proposed to explain the interaction forces between asphalt binder and mineral aggregate, few have been confirmed and characterized. In comparison with chemical interactions, physical adsorption has been considered to play a more important role in adhesive bonding between asphalt and mineral aggregate. In this study, the silicon tip of an atomic force microscope was used to represent silicate minerals in aggregate, and a nanoscale analysis of the characteristics of adhesive bonding between asphalt binder and the silicon tip was conducted via an atomic force microscopy (AFM) test and molecular dynamics (MD) simulations. The results of the measurements and simulations could help in better understanding of the bonding and debonding procedures in asphalt-aggregate mixtures during hot mixing and under traffic loading. MD simulations on a single molecule of a component of asphalt and monocrystalline silicon demonstrate that molecules with a higher atomic density and planar structure, such as three types of asphaltene molecules, can provide greater adhesive strength. However, regarding the real components of asphalt binder, both the MD simulations and AFM test indicate that the colloidal structural behavior of asphalt also has a large influence on the adhesion behavior between asphalt and silicon. A schematic model of the interaction between asphalt and silicon is presented, which can explain the effect of aging on the adhesion behavior of asphalt. PMID:27115043

  13. 胶粉参数对橡胶沥青性能的影响%Impact of Rubber Powder Parameters on the Performance of Rubber Asphalt

    Institute of Scientific and Technical Information of China (English)

    李小成

    2014-01-01

    汽车工业的飞速发展,造成了大量橡胶轮胎的废弃,而研磨后的胶粉却又是沥青改性中良好的外加剂。文中通过室内高速剪切搅拌的方法将不同目数的胶粉颗粒溶于70号的普通沥青中,并对改性后的橡胶沥青进行软化点等沥青三大指标的测试。得出结论:胶粉掺量为20%时,胶粉颗粒越细,则配制的橡胶沥青综合指标所表现出来的优势就越明显。%The rapid development of automobile industry results a large number of discarded rubber tires. But the milled rubber powder is a good admixture of asphalt. The article puts the different meshes of rubber powder into the No.70 ordinary asphalt liquid by the high shear agitation method and then tested the three indicators of modified rubber asphalt. Finally, the article draws the conclusion that the particle of rubber powder is more smaller and the comprehensive indexes of rubber asphalt are more obvious when the content of rubber powder is 20%.

  14. Performance related characterisation of the mechanical behaviour of asphalt mixtures

    NARCIS (Netherlands)

    Molenaar, J.M.M.

    2004-01-01

    The investigation was undertaken to support innovations in the field of asphalt pavement design and material selection, and to be able to evaluate or judge the risk of failure and cost-effectiveness of newly developed paving materials in order to justify their application. To be able to determine th

  15. Performance of Recycled Asphalt Pavement as Coarse Aggregate in Concrete

    Directory of Open Access Journals (Sweden)

    Fidelis O. OKAFOR

    2010-12-01

    Full Text Available Recycled asphalt pavement (RAP is the reclaimed and reprocessed pavement material containing asphalt and aggregate. Most RAP is recycled back into pavements, and as a result there is a general lack of data pertaining to the mechanical properties for RAP in other possible applications such as Portland cement concrete. In the present study, some mechanical properties of Portland cement concrete containing RAP as coarse aggregate were investigated in the laboratory. Six concrete mixes of widely differing water/cement ratios and mix proportions were made using RAP as coarse aggregate. The properties tested include the physical properties of the RAP aggregate, the compressive and flexural strengths of the concrete. These properties were compared with those of similar concretes made with natural gravel aggregate. Results of the tests suggest that the strength of concrete made from RAP is dependent on the bond strength of the “asphalt-mortar” (asphalt binder-sand-filler matrix coatings on the aggregates and may not produce concrete with compressive strength above 25 MPa. However, for middle and low strength concrete, the material was found to compare favorably with natural gravel aggregate.

  16. The asphalt paving process: plans for action research

    NARCIS (Netherlands)

    Miller, Seirgei; Huerne, ter Henny; Dorée, André; Atkin, Brian; Borgbrant, Jan

    2007-01-01

    Recent significant changes in public sector procurement in the Netherlands are forcing road construction companies to professionalize one of their primary processes: on-site asphalt paving. This paper describes an initiative aimed at improving quality in the process. A literature review confirmed th

  17. Sinopec Wins Bid for Special Asphalt for Racing Track

    Institute of Scientific and Technical Information of China (English)

    2004-01-01

    @@ On February 13 Sinopec and Shanghai International Circuit held a signing ceremony in Beijing for the contract to supply special asphalt for racing track use. Mr. Wang Jiming,Vice Board Chairman and President of Sinopec and Mr. Wang Tianpu, Senior Vice President of Sinopec, attended the ceremony.

  18. Assessment of Water Quality of Runoff from Sealed Asphalt Surfaces

    Science.gov (United States)

    This report discusses the results of runoff tests from recently-sealed asphalt surfaces conducted at EPA's Urban Watershed Research Facility (UWRF) in Edison, New Jersey. Both bench-scale panels and full-scale test plots were evaluated. Full-scale tests were performed on an asp...

  19. Asphalt and Wood Shingling. Roofing Workbook and Tests.

    Science.gov (United States)

    Brown, Arthur

    This combination workbook and set of tests contains materials on asphalt and wood shingling that have been designed to be used by those studying to enter the roofing and waterproofing trade. It consists of seven instructional units and seven accompanying objective tests. Covered in the individual units are the following topics: shingling…

  20. Microstructure - based continuum damage model for Asphalt mixes

    International Nuclear Information System (INIS)

    Full text.Hot mix asphalt (HMA) is a complex composite material that consists of different sizes of aggregates, asphalt binder and air voids. One of the most important failures in asphalt pavements is caused by permanent deformation under high service temperature. An HMA with high resistance to permanent deformation work-hardens under repeated loading with accumulating strain. However, HMA that is susceptible to permanenr deformation develop microcracks under repeated loading, which softens the mix and leads ao an increase in the rate of accumulated strain. Most of macroscopic response of HMA, assume isotropic material properties and do not account for the microscopic behavior. This study develops a viscoplastic constitutive model for asphalt mixtures that incorporates microstructure parameters. The model is based on Perzyna's elasto-viscoplastic theory. The viscous flow function is extended to reflect the microstructure anisotropy. In addition, a damage parameter is included in the model to reflect the initiation adn propagation of cracks. The model's parameters are obtained using image analysis procedures, static creep tests and strength tests. The model is used to describe the behavior of number of mixtures with known field performance

  1. Characterization of Brazilian asphalt using X-ray diffraction

    International Nuclear Information System (INIS)

    Asphalt is a sticky, black and highly viscous liquid or semi-solid that is presented in most crude petroleum and in some natural deposits. The X ray diffraction can give valuable information over the characteristics of a material. Thus, the X-ray diffraction (XRD) method was employed to investigate parameters that characterize and differentiate asphalt groups (Boscan, CAP20, CAP40, CAP50/60, CAP50/70 and CAP85/100). The scattering measurements were carried out in θ-2θ reflection geometry using a powder diffractometer Shimadzu XRD-6000 at the Nuclear Instrumentation Laboratory, Brazil. Scans were typically done from 8 deg to 28 deg every 0.05. The parameters analyzed were: FWHM, peak area, peak center, peak height, left half width and right half width. Thus, in this study, scattering profiles from different asphalt groups were carefully measured in order to establish characteristic signatures of these materials. The results indicate that by using three parameters (peak centroid, peak area and peak intensity) it is possible to characterize and differentiate the asphalt. (author)

  2. Improvement of the asphalt-waste products in leachability

    International Nuclear Information System (INIS)

    To improve in leachability of the asphalt products containing evaporator residue from BWR, a method of reducing the swelling of asphalt products, which is a major cause for increasing the leachability, has been developed. Leachability of the resultant asphalt products was examined by IAEA's method. The reduction of swelling is achieved successfully by addition of an equivalent quantity of calcium chloride to the sodium sulfate contained in the residue; the sodium sulfate is converted to calcium sulfate and sodium chloride. The specimen (Asphalt/Na2SO4: 0.5) prepared by this improved method shows little swelling when immersed in water. The specimen without addition of calcium chloride gives a cumulative leaching fraction of about 0.65 for 137Cs and 0.20 for 60Co in 30 days. On the contrary, the corresponding values in about 100 days of the specimen with calcium chloride added are 5 x 10-4 and 1 x 10-4 for 137Cs and 60Co, respectively. These results indicate that the method is promising for reducing the leachability. Coating of the specimen surface with a fresh bitumen further reduces the leachability to a negligibly small value. (author)

  3. Mechanistic and Economical Characteristics of Asphalt Rubber Mixtures

    Directory of Open Access Journals (Sweden)

    Mena I. Souliman

    2016-01-01

    Full Text Available Load associated fatigue cracking is one of the major distress types occurring in flexible pavement systems. Flexural bending beam fatigue laboratory test has been used for several decades and is considered to be an integral part of the new superpave advanced characterization procedure. One of the most significant solutions to prolong the fatigue life for an asphaltic mixture is to utilize flexible materials as rubber. A laboratory testing program was performed on a conventional and Asphalt Rubber- (AR- gap-graded mixtures to investigate the impact of added rubber on the mechanical, mechanistic, and economical attributes of asphaltic mixtures. Strain controlled fatigue tests were conducted according to American Association of State Highway and Transportation Officials (AASHTO procedures. The results from the beam fatigue tests indicated that the AR-gap-graded mixtures would have much longer fatigue life compared with the reference (conventional mixtures. In addition, a mechanistic analysis using 3D-Move software coupled with a cost analysis study based on the fatigue performance on the two mixtures was performed. Overall, analysis showed that AR modified asphalt mixtures exhibited significantly lower cost of pavement per 1000 cycles of fatigue life per mile compared to conventional HMA mixture.

  4. Using waste plastic bottles as additive for stone mastic asphalt

    International Nuclear Information System (INIS)

    Highlights: → The PET increased the stiffness level of the mixture improving its resistance level against permanent deformation. → The effects of waste PET on Marshall Stability, air void and bulk specific gravity of the mixture are significant. → The appropriate amount of PET was found to be 6% by weight of bitumen. -- Abstract: Currently, polymer modified asphalt mixture is a relatively costly mixture for paving roads. One way to reduce the cost of such constructions and rendering them more convenient is by using inexpensive polymers, i.e. waste polymers. The main purpose of this research is to determine the effect of incorporating waste plastic bottles (Polyethylene Terephthalate (PET)) on the engineering properties of stone mastic asphalt (SMA) mixture. The volumetric and mechanical properties of asphalt mixes that include various percentages of PET (0%, 2%, 4%, 6%, 8% and 10%) were calculated and assessed with laboratory tests. The appropriate amount of PET was found to be 6% by weight of bitumen. The outcomes were statistically analysed and the determination of the significance at certain confidence limits was performed with the two factor variance analysis (ANOVA). Moreover, some studies conducted on polyethylene modified asphalt mixture have also been taken into consideration in this paper. The results show that the addition of PET has a significant positive effect on the properties of SMA and it can promote the re-use of waste material in industry in an environmentally friendly and economical way.

  5. A study of sound absorption by street canyon boundaries and asphalt rubber concrete pavement

    Science.gov (United States)

    Drysdale, Graeme Robert

    A sound field model, based on a classical diffusion equation, is extended to account for sound absorption in a diffusion parameter used to model sound energy in a narrow street canyon. The model accounts for a single sound absorption coefficient, separate accommodation coefficients and a combination of separate absorption and accommodation coefficients from parallel canyon walls. The new expressions are compared to the original formula through numerical simulations to reveal the effect of absorption on sound diffusion. The newly established analytical formulae demonstrate satisfactory agreement with their predecessor under perfect reflection. As well, the influence of the extended diffusion parameter on normalized sound pressure levels in a narrow street canyon is in agreement with experimental data. The diffusion parameters are used to model sound energy density in a street canyon as a function of the sound absorption coefficient of the street canyon walls. The acoustic and material properties of conventional and asphalt rubber concrete (ARC) pavement are also studied to assess how the crumb rubber content influences sound absorption in street canyons. The porosity and absolute permeability of compacted specimens of asphalt rubber concrete are measured and compared to their normal and random incidence sound absorption coefficients as a function of crumb rubber content in the modified binder. Nonlinear trends are found between the sound absorption coefficients, porosity and absolute permeability of the compacted specimens and the percentage of crumb rubber in the modified binders. The cross-sectional areas of the air voids on the surfaces of the compacted specimens are measured using digital image processing techniques and a linear relationship is obtained between the average void area and crumb rubber content. The measured material properties are used to construct an empirical formula relating the average porosity, normal incidence noise reduction coefficients and

  6. Some Properties of Emulsified Asphalt Paving Mixture at Iraqi Environmental Conditions

    Directory of Open Access Journals (Sweden)

    Shakir.A.Al-Mishhadani

    2014-02-01

    Full Text Available Cold emulsified asphalt mixture is generally a mix made of emulsified asphalt withaggregate. Emulsified asphalt is manufactured from base asphalt, emulsifier agent and waterwith approximate percentage of 40% to 75% asphalt, 0.1% to 2.5% emulsifier and 25% to60% water plus some minor components. This study aims to use the cold emulsified asphaltmixtures for road construction and maintenance in Iraq as an alternative to the hot asphaltmixtures, due to its economical, practical and environmental advantages. This studyfocusedto test and evaluates the emulsified asphalt material properties to be used as paving mixture.The tested properties of emulsified asphalt mixture were bulk density, air voids, dry Marshallstability, wet Marshall stability, retained Marshall stability, flow tests and compared with thecommon used specification.The results indicate that the emulsified asphalt type cationic slowsetting low viscosity (CSS-1 is very suitable with quartz type of aggregate from Al-Nibaayquarry. From many trial mixes it is found that the best percentages of initial residual bitumencontent to produced adequateresults for coating test ,mixing ,compaction ,curing and Marshallstability were ranged from (2.5%, 3%,3.5%,4% and 4.5%, andthe optimum percentage is(3.5%.Finally it can be conducted that the emulsified asphalt mixture is a suitable alternativemixture to the hot asphalt mixture for road construction and maintenance in Iraq.

  7. Some Properties of Emulsified Asphalt Paving Mixture at Iraqi Environmental Conditions

    Directory of Open Access Journals (Sweden)

    Shakir.A.Al-Mishhadani* Hasan.H.Al-Baid

    2014-04-01

    Full Text Available Cold emulsified asphalt mixture is generally a mix made of emulsified asphalt withaggregate. Emulsified asphalt is manufactured from base asphalt, emulsifier agent and waterwith approximate percentage of 40% to 75% asphalt, 0.1% to 2.5% emulsifier and 25% to60% water plus some minor components. This study aims to use the cold emulsified asphaltmixtures for road construction and maintenance in Iraq as an alternative to the hot asphaltmixtures, due to its economical, practical and environmental advantages. This studyfocusedto test and evaluates the emulsified asphalt material properties to be used as paving mixture.The tested properties of emulsified asphalt mixture were bulk density, air voids, dry Marshallstability, wet Marshall stability, retained Marshall stability, flow tests and compared with thecommon used specification.The results indicate that the emulsified asphalt type cationic slowsetting low viscosity (CSS-1 is very suitable with quartz type of aggregate from Al-Nibaayquarry. From many trial mixes it is found that the best percentages of initial residual bitumencontent to produced adequateresults for coating test ,mixing ,compaction ,curing and Marshallstability were ranged from (2.5%, 3%,3.5%,4% and 4.5%, andthe optimum percentage is(3.5%.Finally it can be conducted that the emulsified asphalt mixture is a suitable alternativemixture to the hot asphalt mixture for road construction and maintenance in Iraq.  

  8. Effect of the weather in the aging of asphalts by XRD

    International Nuclear Information System (INIS)

    Asphalt is a sticky, black and highly viscous liquid or semi-solid that is presented in most crude petroleum and in some natural deposits. As is well known, asphalt has been the preferential choice in pavement construction since excellent utility of pavement, however, as other organic substances, it is also subjected to aging phenomena evolving with time. Asphalt aging is one of the principal factors causing deterioration of asphalt pavements. The photodegradation of asphalts must be considered in the study of the performance of asphalt pavement, especially in geographical regions where high solar radiation intensity occurs. It has an important influence in asphalt aging in tropical places as Brazil. Many methods have been applied to simulate aging of bitumen. It was just a simulation but not real aging asphalt. In this study we submitted the asphalt to the weather as sun and rain. Periodically, during 430 days, the XRD profiles were done and the results analyzed. The scattering measurements were carried out in 0-20 reflection geometry using a powder diffractometer Shimadzu XRD-6000. Scans were typically done from 8 deg to 28 deg every 0.05 deg. The parameters FWHM and peak centroid were analyzed. From 0 until 180 days the aging was faster. The peaks were marked and analyzed with the pass of time. The crystallinity of asphalt increase with weather exposition. Some angles of profiles changed the position indicating change of atomics plans. (author)

  9. Evaluation system for CO2 emission of hot asphalt mixture

    Directory of Open Access Journals (Sweden)

    Bo Peng

    2015-04-01

    Full Text Available The highway construction industry plays an important role in economic and development, but is also a primary source of carbon emission. Accordingly, with the global climate change, energy conservation and reduction of carbon emissions have become critical issues in the highway construction industry. However, to date, a model for the highway construction industry has not been established. Hence, to implement a low-carbon construction model for highways, this study divided asphalt pavement construction into aggregate stacking, aggregate supply, and other stages, and compiled a list of energy consumption investigation. An appropriate calculation model of CO2 emission was then built. Based on the carbon emission calculation model, the proportion of carbon emissions in each stage was analyzed. The analytic hierarchy process was used to establish the system of asphalt pavement construction with a judgment matrix, thereby enabling calculation of the weight coefficient of each link. In addition, the stages of aggregate heating, asphalt heating, and asphalt mixture mixing were defined as key stages of asphalt pavement construction. Carbon emissions at these stages accounted for approximately 90% of the total carbon emissions. Carbon emissions at each stage and their impact on the environment were quantified and compared. The energy saving construction schemes as well as the environmental and socioeconomic benefits were then proposed. Through these schemes, significant reductions in carbon emissions and costs can be achieved. The results indicate that carbon emissions reduce by 32.30% and 35.93%, whereas costs reduce by 18.58% and 6.03%. The proposed energy-saving and emission reduction scheme can provide a theoretical basis and technical support for the development of low-carbon highway construction.

  10. 废橡胶粉改性沥青性能的研究%The Performance of Asphalt Modified by Crumb Rubber

    Institute of Scientific and Technical Information of China (English)

    李国峰; 陈梅

    2016-01-01

    Using Karamay AH-110 asphalt as the base, crumb rubber as a modifier, by wet blending method, high-performance crumb rubber modified asphalt was prepared under the condition of swelling time 2 h, shearing time 1.5 h, the shear temperature 186℃ and the shear rate 7 000 r/min. By changing the amount of powder and particle size, effect of powder on the performance of modified asphalt was studied, and the mechanism of the rubber modified asphalt was discussed. The experimental results show that, blending waste rubber powder can significantly improve asphalt softening point, penetration and ductility; the optimal content of crumb rubber is 15%, the best particle size is 80 mesh.%以克拉玛依A H -110沥青为基体,废橡胶粉为改性剂,采用湿法共混,在溶胀时间为2 h,剪切时间为1.5 h,剪切温度为186℃,剪切速率为7000 r/min的条件下,制备出高性能废胶粉改性沥青。通过改变胶粉的用量和胶粉的粒径,研究了胶粉对改性沥青性能的影响,探讨了胶粉改性沥青机理。结果表明:废橡胶粉的掺入使沥青的软化点、针入度、延度都有明显改善。研究发现废橡胶粉的最佳掺量为15%,最佳粒径为80目。

  11. A Study on Design and Properties of Epoxy Asphalt Mixtures%环氧沥青混合料设计及性能研究

    Institute of Scientific and Technical Information of China (English)

    丛培良; 陈拴发; 陈华鑫

    2012-01-01

    采用体积设计方法,研究了环氧沥青混合料级配组成和成型前后养护时间对混合料性能的影响.试验结果表明:采用体积设计方法设计的环氧沥青混合料粗集料多,空隙率小,保证了环氧沥青混合料具有良好的抗滑性和抗渗性能.环氧沥青混合料成型前后养护时间影响试件的空隙率、矿料间隙率、沥青饱和度、稳定度和劈裂强度.成型前经过养护的环氧沥青混合料,成型后初始稳定度和劈裂强度比成型前未经过养护的高;但成型前经过养护试件的最终稳定度和劈裂强度低于成型前未经过养护的试件.而且,环氧沥青混合料在60℃养护7d后,已经具有良好的抗水损害性能和抗车辙性能.%Epoxy asphalt mixture is prepared using volume design methods. The effect of curing condition before and after modeled on properties of epoxy asphalt mixture and mixture composition are investigated. The results indicate that epoxy asphalt mixture consist of high coarse aggregate content and low void using volume design method. It can ensure mixture keeping better skid resistance and permeability resistance. The void, voids in mineral aggregate, voids filled with asphalt, Marshall stability and indirect tensile strength of epoxy asphalt mixture increase when mixture is deposited in oven before modeled. But Marshall stability and indirect tensile strength of deposited1 mixture are lower than that of no deposited before modeled. And epoxy asphalt mixture has better water damage resistance and rut resistance when epoxy asphalt mixture is cured 7 day at 60℃.

  12. Performance Test of Rubber Asphalt and Analysis of Influencing Factors%橡胶沥青性能试验及影响因素分析

    Institute of Scientific and Technical Information of China (English)

    刘子兴; 常立峰

    2011-01-01

    Aiming at road performance of rubber asphalt and influencing factors, this paper studies influences of types of rubber powder, content of rubber powder, types of base asphalt and mixing temperature, etc. on high-temperature, low-temperature and ageing resistant properties, etc. of rubber asphalt via indoor test. The test result shows that the high-temperature, low-temperature and fatigue resisting properties of asphalt have been improved to some degree after addition of rubber powder. Among them high-temperature property of modified asphalt with 20-mesh rubber powder is better than that of modified asphalt with 40-mesh and 60-mesh rubber powders, and the low-temperature and fatigue resisting properties of all three rubber powders are relatively approximate. For CNOOC (Taizhou) AH-70 base asphalt, when 20-mesh rubber powder for truck tires is adopted for modification, the optimal dosage is 16% ~18%.%针对橡胶沥青的路用性能及其影响因素,通过室内试验研究胶粉类型、胶粉掺量、基质沥青类型、拌和温度等对橡胶沥青高温、低温和抗老化性能等的影响.试验结果表明:添加胶粉后,沥青的高温、低温及抗疲劳性能均有不同程度的改善.其中,20目胶粉改性沥青的高温性能优于40和60目胶粉改性沥青,三者低温以及抗疲劳性能则比较接近;对于中海油(泰州)AH-70基质沥青而言,当采用20目货车轮胎胶粉改性时,最佳掺量为16%~18%.

  13. Decision of National and Provincial Highway Asphalt Pavement Structure Based on Value Engineering

    Directory of Open Access Journals (Sweden)

    Yingwei Ren

    2014-01-01

    Full Text Available It is important that decision of asphalt pavement structure requires overall considerations of the performance and financial investment. To have asphalt pavement structure fulfilling good reliability, the asphalt pavement structure decision was researched based on value engineering theory. According to the national and provincial highway investigation data in Shandong Province during the last decade, the asphalt pavement performance attenuation rules of traffic levels and asphalt layer thicknesses were developed, and then the road performance evaluation method was presented. In addition, the initial investments, the costs of road maintenance, and middle-scale repair in a period were analyzed. For the light traffic and medium traffic example, using the value engineering method, the pavement performance and costs of which thickness varies from 6 cm to 10 cm were calculated and compared. It was concluded that value engineering was an effective method in deciding the asphalt pavement structure.

  14. Accelerated aging of catalytically airblown asphalt membranes under simulated uranium mill tailings impoundment conditions

    International Nuclear Information System (INIS)

    This paper evaluates the performance of asphalt membranes by examining the chemical and permeability changes experienced by the asphalt during aging tests. The aging process was accelerated by exposing the asphalt to elevated temperatures, high oxygen concentrations, and increased strengths of aqueous oxidizing agents. The synergistic effects of the variables are evaluated by using a fractional factorial experimental design. The installation costs for a catalytically airblown asphalt liner are roughly half that of the typical polymeric materials, and also less than the rubberized asphalt membrane. The results of the initial accelerated aging tests of the asphalt membranes indicate that this material will provide stable, long-term leachate isolation in a mill tailings environment

  15. 温度对温拌橡胶沥青混合料体积参数的影响%Influence of Temperature on Volumetric Parameters of Asphalt Rubber Mixture with Warm-Mix Additive

    Institute of Scientific and Technical Information of China (English)

    王翼; 刘黎萍; 孙立军

    2013-01-01

    Influence of mixing and compaction temperature on volumetric parameters was analyzed for differently graded asphalt rubber mixtures with warm-mix additive.Best asphalt-aggregate ratios of asphalt rubber mixtures with three different gradations and filler contents were determined by the Marshall test firstly.Mixture samples with DAT-H5 were made with different mixing and compaction temperatures.A comparative analysis of volumetric parameters was conducted and evaluated by the rutting test and freezethaw split test.The results show that the asphalt-aggregate ratio determines the technical feasibility of asphalt rubber mixture with DAT-H5.The mixing temperature has significant effect on compaction temperature of asphalt rubber mixtures with DAT-H5 as well.Based on the criteria of air void,the mixing and compaction temperature of asphalt rubber mixture with DAT-H5 could be almost reduced by 30 ℃ compared with the common asphalt rubber mixtures.The high-temperature performance of asphalt rubber stone matrix with DAT-H5 is ensured,while the water stability decreases somewhat.%通过室内试验研究了拌和与成型温度对添加温拌剂的不同级配橡胶沥青混合料体积参数的影响.设计了3种填隙方式的热拌橡胶沥青混合料,对添加DAT-H5温拌剂、采用不同拌和及成型温度的混合料体积参数进行了对比分析,并利用车辙与冻融劈裂试验验证了温拌剂的有效降温幅度.结果表明:油石比对温拌橡胶沥青混合料的技术可行性影响显著;拌和温度对温拌剂降低橡胶沥青混合料所需成型温度的作用影响较为明显;以空隙率为指标,温拌橡胶沥青玛蹄脂碎石混合料拌和与成型温度较热拌橡胶沥青混合料可降低约30℃,高温稳定性良好,但水稳定性有所下降.

  16. Development of asphaltic mix with waste products use

    Directory of Open Access Journals (Sweden)

    Pugin Konstantin Georgievich

    2014-07-01

    Full Text Available The trend of high growth of the vehicle fleet in Russia along with the positive impact on the socio-economic development of the country has a number of adverse consequences, one of which is the high accident rate on the roads. The paper considers modern way to provide the safe vehicles flow with the use of colored asphalt, which is a kind of hot asphalt and can have a variety of colors, which consists of coloring pigments. The conventional method of coloring the asphalt mix is produced by adding color rubble or pigmenting additives. The task, which was put forward, was the establishment of such road concrete mix, from which, without the use of primary materials and without increasing the consumption of bitumen, asphalt concrete road surfaces of acceptable strength could be obtained. As a pigment the dust of gas purification system of electrical furnace DSP - 60 of «Kamastal» plant, Perm, was used. The composition of the dust waste from the furnace consists of metal oxides and silicates. Dust-gas-cleaning is a fine powder with a high specific surface (1.2…2.5 thousand cm /g and bulk density of 3.7…4.2 g/cm . The powder color is dark brown. The density of the ready colored asphalt samples is 2.47...2.49 g/cm , and water saturation is 3.50…3.55 %. As a result of the research the diagrams of the dependence of road concrete mix’s water saturation from dust percentage and a diagram of dependence of concrete mixes’ durability from dust percentage at t = 20° and 50° C were built. After analyzing the obtained curves it can be concluded that the increase of the percentage of dust leads to increase of water saturation of road concrete mix and reduced strength. Thus, the developed asphalt concrete mix allows visually separating the lanes on the road, it has the relevant regulatory requirements durability and water resistance. This mixture corresponds to the type B mark III and can be used in regions I, II, and partly III of road-climatic zones

  17. Fatigue laws for Brazilians asphalt rubber mixtures obtained in 4 point bending tests

    OpenAIRE

    Fontes, Liseane P. T. L.; Trichês, Glicério; Pais, Jorge C.; Pereira, Paulo A. A.

    2009-01-01

    The majority of Brazilian roadpavements consistsof thin pavement structures unable to resist the damage caused by heavy loads and an increasing traffic demand. The main structural distress modes found in Brazilians asphalt layers is fatigue cracking. One of the prom-ising techniques to improve the pavement performance is through asphalt rubber mixtures, which make use of crumb rubber from scrap tires to modify and enhance the properties of the asphalt. The inexistence of fatigue laws for asph...

  18. Effects of Crumb Rubber Size and Concentration on Performance of Porous Asphalt Mixtures

    OpenAIRE

    Altan Cetin

    2013-01-01

    The purpose of this study is to investigate the effect of size distribution and concentration of crumb rubber on the performance characteristics of porous asphalt mixture. The recycling of scrap tires in asphalt pavements appears as an important alternative providing a large-scale market. The characteristics of bitumen are very important with regard to service life of porous asphalt pavement. The experimental study consists of two main steps. Firstly, the mixture design was performed to deter...

  19. The reinforcement and healing of asphalt mastic mixtures by rejuvenator encapsulation in alginate compartmented fibres

    Science.gov (United States)

    Tabaković, A.; Post, W.; Cantero, D.; Copuroglu, O.; Garcia, S. J.; Schlangen, E.

    2016-08-01

    This paper explores the potential use of compartmented alginate fibres as a new method of incorporating rejuvenators into asphalt pavement mixtures. The compartmented fibres are employed to locally distribute the rejuvenator and to overcome the problems associated with spherical capsules and hollow fibres. The work presents proof of concept of the encapsulation process which involved embedding the fibres into the asphalt mastic mixture and the survival rate of fibres in the asphalt mixture. To prove the effectiveness of the alginate as a rejuvenator encapsulating material and to demonstrate its ability survive asphalt production process, the fibres containing the rejuvenator were prepared and subjected to thermogravimetric analysis and uniaxial tensile test. The test results demonstrated that fibres have suitable thermal and mechanical strength to survive the asphalt mixing and compaction process. The CT scan of an asphalt mortar mix containing fibres demonstrated that fibres are present in the mix in their full length, undamaged, providing confirmation that the fibres survived the asphalt production process. In order to investigate the fibres physiological properties and ability to release the rejuvenator into cracks in the asphalt mastic, the environmental scanning electron microscope and optical microscope analysis were employed. To prove its success as an asphalt healing system, compartmented alginate fibres containing rejuvenator were embedded in asphalt mastic mix. The three point bend tests were performed on the asphalt mastic test samples and the degree to which the samples began to self-heal in response was measured and quantified. The research findings indicate that alginate fibres present a promising new approach for the development of self-healing asphalt pavement systems.

  20. Analysis of Load Stress for Asphalt Pavement of Lean Concrete Base

    Science.gov (United States)

    Lijun, Suo; Xinwu, Wang

    The study revealed that whether it is early distresses in asphalt pavement or not depends largely on working performance of base. In the field of asphalt pavement, it is widely accepted that lean concrete base, compared with the general semi-rigid base, has better working performance, such as high strength and good eroding resistance. Problem of early distresses in asphalt pavement, which caused by more traffic loadings, can be settled effectively when lean concrete is used in asphalt pavement. Traffic loading is important parameter used in the analysis of the new pavement design. However, few studies have done extensive and intensive research on the load stress for asphalt pavement of lean concrete base. Because of that, it is necessary to study the load stress for the asphalt pavement. In the paper, first of all, three-dimension finite element model of the asphalt pavement is created for the aim of doing mechanical analysis for the asphalt pavement. And then, the two main objectives of this study are investigated. One is analysis for load stress of lean concrete base, and the other is analysis for load stress of asphalt surface. The results show that load stress of lean concrete base decreases, decrease and increase with increase of base's thickness, surface's thickness and ratio of base's modulus to foundation's modulus respectively. So far as the asphalt surface is concerned, maximum shearing stress, which is caused by load, is evident in asphalt surface which is located in transverse contraction joint of lean concrete base of asphalt pavement. Maximum shearing stress decrease, decrease, decrease and increase respectively with increase of the surface's modulus, the surface's thickness, base's thickness and ratio of base's modulus to foundation's modulus.

  1. APPLICATION OF PACKING THEORY ON GRADING DESIGN FOR POROUS ASPHALT MIXTURES

    OpenAIRE

    Hardiman Hardiman

    2004-01-01

    The design life of porous asphalt is shorter than dense mix as a consequence of permeability loss due to clogging and poor resistance to disintegration. To mitigate problems associated with clogging, double layer porous asphalt has been constructed in the Netherlands. This paper investigated a development of a new grading design for porous asphalt by varying percentage of aggregate with maximum sizes of 20, 14 and 10mm; a theory of packing was used. The most common method used for grading des...

  2. Characterization of Various Plant-Produced Asphalt Concrete Mixtures Using Dynamic Modulus Test

    OpenAIRE

    Muhammad Irfan; Asad S. Waraich; Sarfraz Ahmed; Yasir Ali

    2016-01-01

    This research characterizes the performance of various plant-produced asphalt concrete mixtures by dynamic modulus |E∗| test using asphalt mixture performance tester (AMPT). Marshall designed specimens of seven different mixtures were prepared using the Superpave gyratory compactor and subjected to sinusoidal compressive loading at various temperatures (4.4 to 54.4°C) and loading frequencies (0.1 to 25 Hz). A catalog of default dynamic modulus values for typical asphalt concrete mixtures of P...

  3. Modeling of asphalt by means of discrete element method – an initial study

    OpenAIRE

    Feng, Huan; Hededal, Ole; Stang, Henrik

    2013-01-01

    Asphalt is a viscous material consisting of a matrix of stones, sand and filler glued together by a bituminous binder, which is used in many pavement constructions. Knowledge about asphalt is mainly based on the results of experimental and empirical investigation, which comes at the expense of conducting time-consuming and lab-costly procedures. The use of numerical models, capable of reducing greatly the testing cost, has shown great potential in characterizing asphalt-aggregate mixtures for...

  4. The Effects of Salt on Rheological Properties of Asphalt after Long-Term Aging

    OpenAIRE

    Xin Yu; Ying Wang; Yilin Luo; Long Yin

    2013-01-01

    Limited studies in recent years have shown that asphalt pavement subject to seawater in coastal regions or deicing salt in cold regions may be seriously damaged after being soaked in saline water for a long time. However, there is limited research into the influence of salt on rheological properties of asphalt after long-term aging. In this study, rheological properties of unmodified and polymer-modified asphalt after long-term aging were tested after being soaked in different concentrations ...

  5. Study on triaxial test method and failure criterion of asphalt mixture

    OpenAIRE

    Jianlong Zheng; Tuo Huang

    2015-01-01

    Asphalt mixture is the most widely used pavement material all over the world. In China, more than 90% of service expressways are asphalt pavement. However, current asphalt pavement design method still has irrationality. Even though maximum tensile stress theory is used as failure criterion, pavement structure under the effects of wheel load is in three-dimensional complex stress state. Obviously, one-dimensional strength theory cannot reflect the failure characteristics and the resistance of ...

  6. Development of an innovative bio-binder using Asphalt-rubber technology

    OpenAIRE

    Peralta, J.; Silva, Hugo Manuel Ribeiro Dias da; Williams, R. Christopher; Rover, Marjorie; Machado, A.V.

    2013-01-01

    This research work evaluates several parameters that can affect Asphalt Rubber (AR) binder performance and applies the AR technology to the development of an innovative renewable bio-binder that can fully and cost-effectively replace asphaltic bitumen derived from petroleum in flexible pavement construction. The “Binder Accelerated Separator” method was used to divide the constituents of the Asphalt Rubber and bio-binder (residual binder and swelled rubber). The physical and chemi...

  7. Asphalt rubber interlayer benefits on reflective crack retardation of flexible pavement overlays

    OpenAIRE

    Shakir, Shatnawi; Pais, Jorge; Minhoto, Manuel

    2011-01-01

    This paper provides an overview of the asphalt rubber interlayer benefits on reflective crack retardation in flexible pavement preservation and rehabilitation strategies. These interlayers are known in California as asphalt rubber absorbing membrane interlayers (SAMI-R) or as asphalt rubber aggregate membrane interlayers (ARAM-I) chip seals. These interlayers have been used successfully as part of cape seals and as part of an overlay system. The paper focuses on the performance in terms of fi...

  8. Asphalt rubber interlayer benefits in minimizing reflective cracking of overlays over rigid pavements

    OpenAIRE

    Shatnawi, Shakir; Pais, Jorge; Minhoto, Manuel

    2012-01-01

    This paper provides an overview of the asphalt rubber interlayer benefits on reflective crack retardation in overlays over rigid pavements. These interlayers are known in California as asphalt rubber absorbing membrane interlayers (SAMI-R) or as asphalt rubber aggregate membrane interlayers (ARAM-I) chip seals. The paper focuses on the performance in terms of field project reviews, laboratory performance tests and finite element analysis. SAMI-R has been given a reflective cracking equivalent...

  9. Effect of cryogenic and ambient crushed rubber on the mechanical properties of hot mixes asphalts

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Márcio Muniz de; Pais, Jorge C.

    2009-01-01

    The crumb rubber used to produce asphalt rubber binders can be obtained either through the ambient grinding or the cryogenic processes. The final product obtained usually presents significant differences which influence the physical properties of asphalt rubber binders and, consequently, the mechanical properties of the asphalt rubber hot mixes produced with these modified binders. The objective of the study presented in this paper is to learn about the influence that the type of crumb rubber...

  10. Recycled tyre rubber modified bitumens for road asphalt mixtures: a literature review

    OpenAIRE

    Lo Presti, Davide

    2013-01-01

    Nowadays, only a small percentage of waste tyres are being land-filled. The Recycled Tyre Rubber is being used in new tyres, in tyre-derived fuel, in civil engineering applications and products, in moulded rubber products, in agricultural uses, recreational and sports applications and in rubber modified asphalt applications. The benefits of using rubber modified asphalts are being more widely experienced and recognized, and the incorporation of tyres into asphalt is likely to increase. The te...

  11. Use of tire rubber to improve fatigue performance of asphalt mixtures

    OpenAIRE

    Thives, L. P.; Trichês, Glicério; Pereira, Paulo A. A.; Pais, Jorge C.

    2010-01-01

    The accelerated failure of pavements is one of the main problems in Brazilian roads resulting from fatigue cracking due to the repeated application of traffic induced stresses. The incorporation of crumb rubber from waste tires in asphalt, named asphalt rubber, is a method which has been used in several countries to improve the properties of asphalt pavement mixtures and, at the same time, has been a ecologically alternative to deal with the proper disposal of waste tires. This...

  12. The Research on Improvement of Low Temperature Stability for Diatomite Modified Asphalt Mixture with PE Particles

    OpenAIRE

    HU Qiusheng; Zhou, Gang

    2015-01-01

    In light of the lake of low temperature stability for diatomaceous which used as asphalt modifier.Stat the research with the diatomite produced at Jilin Changbai, using the way of low temperature bending test to evaluate the PE and diatomite composite modified asphalt mixture’s low temperature crack resistance performance. The results showed that after the diatomite and PE composite modified asphalt mixture has the best advantage of anti-cracking performance under low-temperature ...

  13. Removal of contaminated asphalt layers by using heat generating powder metallic systems

    International Nuclear Information System (INIS)

    Heat generating systems on the base of powder metallic fuel were used for the removal of contaminated asphalt layers. Decontamination of spots which had complex geometric form was performed. Asphalt layers with deep contamination were removed essentially all radionuclides being retained in asphalt residue. Only a small part (1 - 2 %) of radionuclides could pass to combustion slag. No radionuclides were detected in aerosol-gas phase during decontamination process

  14. Professionalising the asphalt construction process: aligning information technologies, operators' knowledge and laboratory practices

    OpenAIRE

    Bijleveld, Frank Roland

    2015-01-01

    This research addresses the need to professionalise the asphalt construction process. A distinctive action research strategy is designed and carried out to progressively improve operational strategies of asphalt teams from technological, human (operator) and laboratory perspectives. Using information technologies, such as GPS, a laser-linescanner, and infrared cameras, the on-site construction process in made explicit. More than thirty asphalt construction projects are systematically monitore...

  15. Mechanism of Fume Suppression and Performance on Asphalt of Expanded Graphite for Pavement under High Temperature Condition

    Institute of Scientific and Technical Information of China (English)

    HUANG Gang; HE Zhaoyi; HUANG Yangcheng; ZHOU Chao; YUAN Xiaoya

    2014-01-01

    Fume suppression mechanisms and the effect of expanded graphite on the performance of asphalt were studied by applying infrared spectroscopy (FT-IR), X-ray diffraction (XRD), scanning electron microscopy (SEM) and comprehensive thermal analysis (TG, DSC). The experimental results confirm that asphalt which is mixed with expandable graphite will expand in the process of hot mix, and the expanded graphite layer will swell by the light component in the asphalt. The light component in the asphalt and PAHs adsorption on expanded graphite surface or part of the plug in the expanded graphite layer between plates made nucleation crystallization growth. And the Van der Waals force and the bonding of the lattice can effectively restrain the asphalt fume release. Meanwhile, the expanding agent with oxidative can spread into the asphalt, leading to asphalt oxygenated and plastic abate, while the ductility decreases. Expanded graphite, SBS modifier and environment- friendly plasticizers are used to composite modified asphalt. According to asphalt fume release experiment, normal test of asphalt performance, Brookfield viscosity test, RTFOT test and asphalt mixture tests (high temperature stability, low temperature stability, water stability), it has been proven that the modified asphalt’s performance is better than that of matrix asphalt and equivalent to that of SBS modified asphalt. Furthermore, it has good fume suppression effect.

  16. Investigation of self healing behaviour of asphalt mixes using beam on elastic foundation setup

    OpenAIRE

    Qiu, J.; Molenaar, A.A.A.; Van de Ven, M.F.C.; Wu, S.; Yu, J.

    2012-01-01

    Self healing of asphalt mixes is known for more than four decades. However, it is a complex phenomenon which depends on the duration of the rest period, temperature, crack size, etc. In order to quantify the self healing behaviour of asphalt mixes, a test setup was proposed in this research using an asphalt beam on an elastic foundation. Within this setup, a notched asphalt beam was glued on a low modulus rubber foundation, and a symmetric monotonic load was applied with loading–unloading–hea...

  17. USE OF CRUMB RUBBER FROM USED CAR TIRES IN MINERAL ASPHALT MIXES

    Directory of Open Access Journals (Sweden)

    Andrzej Plewa

    2014-11-01

    Full Text Available With the development of the automotive industry the disposal of used tires is constantly growing problem. Storage of waste rubber is associated with a very long period of decomposition of rubber in the natural conditions. Simultaneously new technologies are developed every year, which in the future may significantly promote recycling of this type of materials. The crumb rubbery modification of the road bitumen is the one of the environmentally safe solutions of rubbery decomposition. Improvement of resistance of the crumb rubbery modification of the road asphalt mixtures is the very important ecological aspect of the future. The article presents the results of research on the fatigue life resistance of asphalt concretes AC16P and AC22P with asphalt-rubber binders. The above analyses have been based on the results of tests of fatigue life of mineral-rubber-asphalt mixes determined by the method of prismatic four-point bending (4PB-PR. Mineral-rubber -asphalt mixes have been diversified according to the amount of the additive of rubber fines in asphalt-rubber binder. On the basis of the test results have been proven improvements functional properties mineral-rubber-asphalt mixes compared with mineral-asphalt mixes with unmodified asphalt.

  18. Application of minerals residues in the asphalt composition; Aplicacao de residuos minerais na composicao do asfalto

    Energy Technology Data Exchange (ETDEWEB)

    Ribeiro, Roberto Carlos da C.; Seidl, Peter Rudolf [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica; Correia, Julio Cesar Guedes [Centro de Tecnologia Mineral - CETEM, Rio de Janeiro, RJ (Brazil)

    2004-07-01

    The performance of asphalt pavements depends mainly on the properties of their constituents: mineral aggregates and asphalt cement. The mineral aggregate represents about 95% in weight of asphalt mixtures having a significant influence on the properties and performance of these mixtures. Asphalt cement (CAP) corresponds to the smaller fraction but it is mainly responsible for adsorption on the mineral aggregates. The objective of this study was to evaluate the interaction between different CAPs with residues from granite saw wills in place of mineral aggregates that run up costs with extraction and processing in asphalt production. This way asphalt production costs as well as the environmental problems that are caused by mineral residue are reduced. Five different asphalt cements, referred to as A, B, C, D and E, and a granite residue were used in this work. The results indicated that the residue strongly absorbs all the CAPs that were studied; particularly CAP A, which is considered the most adequate for the production of asphalt from this residue. Preliminary tests this indicate that asphalt production can use mineral residues instead of mineral aggregates in its composition. (author)

  19. Optimization of technical measures for improving high-temperature performance of asphalt-rubber mixture

    Institute of Scientific and Technical Information of China (English)

    Chuan Xiao; Tianqing Ling; Yanjun Qiu

    2013-01-01

    Asphalt-rubber pavements often become dam-aged in high-temperature regions and appear rutted or wavy, and experience slippage. To improve the high-tem-perature performance of the asphalt-rubber mixture, tech-nical measurements, such as, the optimal adjustment of gradation, technique of composite modification, and con-trol of compaction were investigated. An optimal adjust-ment of aggregate gradation based on stone matrix asphalt improves the high-temperature stability of the asphalt-rubber mixture significantly. Through composite modifi-cation, the effect of asphalt-rubber modification was enhanced, and the dynamic stability and relative defor-mation indices of the asphalt-rubber mixture were improved significantly. Furthermore, compaction parame-ters had a significant influence on the high-temperature stability of the asphalt-rubber mixture. The rolling times for compacting the asphalt-rubber mixture should be controlled to within 18-20 round-trips at a molding tem-perature at 180 ?C;if the rolling time is a 12 round-trip, the compaction temperature of the asphalt-rubber mixture should be controlled between 180 and 190 ?C.

  20. Influence of crumb rubber and digestion time on the asphalt rubber binders

    OpenAIRE

    Neto, Silvrano Adonias Dantas; Farias, Márcio Muniz de; Pais, Jorge C.; Pereira, Paulo A. A.; Sousa, Jorge B.

    2006-01-01

    This paper shows the results of a study about the mechanical behavior of dense graded asphalt-rubber hot mixes prepared with two different types of asphalt-rubber binders. These asphalt-rubber binders were obtained with penetration grade asphalt (AC 50/70) mixed with 21% and 25% of crumb rubber in weight. The rubber was recycled from unserviceable tires using the ambient grinding process. Hot mixes made with the conventional binder AC 50/70 were also studied for comparison. The...

  1. Investigation of the Physical and Molecular Properties of Asphalt Binders Processed with Used Motor Oils

    Directory of Open Access Journals (Sweden)

    Mohyeldin Ragab

    2015-01-01

    Full Text Available In this work we investigated the performance aspects of addition of used motor oils (UMO to neat and crumb rubber modified asphalts (CRMA and related that to the change of molecular size distribution of modified asphalt’s fractions; asphaltenes, saturates, naphthene aromatics, and polar aromatics. Based on the results of temperature sweep viscoelastic tests, addition of crumb rubber modifier (CRM alone or with UMO results in the formation of internal network within the modified asphalt. Based on the results of short and long term aged asphalts, the utilization of combination of UMO and CRM enhanced the aging behavior of asphalt. Bending beam rheometer was utilized to investigate the low temperature behavior of UMO modified asphalts. Based on those tests, the utilization of the UMO and CRM enhanced the low temperature properties of asphalts. Based on the results of the asphalt separation tests and the Gel Permeation Chromatography (GPC analysis, it was found that saturates and naphthene aromatics are the two asphalt fractions that have similar molecular size fractions as those of UMO. However, UMO only shifts the molecular sizes of saturates after interaction with asphalt. Results also show that polar aromatics pose higher molecular size structures than UMO.

  2. Decontamination by shotblasting of radioactivity deposited on an asphalt road

    International Nuclear Information System (INIS)

    Long-lived fission products may be deposited in the environment after a serious reactor accident. From previous experiments it is known that if firehosing is to be used for decontamination it has to be done soon after the deposition. It is therefore worthwhile to study another decontamination method. An experimental study has been conducted of how well shotblasting can remove contamination from an asphalt road. In shotblasting a thin layer of the surface is loosened by the impact of small steel balls, and in the same procedure the surface dust is vacuumed up and the steel balls recovered. The contaminant was 86Rb, which behaves as caesium. As reference, the weathering of identical contamination on an asphalt road, a concrete road and a road covered with small concrete stones was studied concurrently. (author)

  3. 10CFR61 waste form conformance program for asphalted radwaste

    International Nuclear Information System (INIS)

    With the enactment of Title 10, Code of Federal Regulations, Part 61, ''Licensing Requirements for Land Disposal of Radioactive Waste'' came the imposition of new requirements on licensees who dispose of radioactive waste via shallow land burial. Specifically, 10CFR61 both imposed a waste classification system requiring segregation of waste according to hazard and established waste performance characteristics required to enhance stability of the burial site. In order to provide licensees with guidance regarding implementation of applicable requirements of 10CFR61, the NRC Low Level Waste Licensing Branch issued two Technical Positions. To demonstrate compliance of asphalted radwaste produced with oxidized asphalt with 10CRF61 criteria and the NRC's Technical Position, five utilities combined resources. The five utilities sponsoring the program were Public Service Electric and Gas Company, Niagara Mohawk Power Company, Detroit Edison Company, New Hampshire Yankee, and Consumers Power Company

  4. Study on the Durability of Steel Deck Pavement Asphalt Mixture Based on Rubber Powder and SBS Compound Modified Technology%基于橡胶粉与 SBS 复合改性技术钢桥面铺筑沥青混合料耐久性试验研究

    Institute of Scientific and Technical Information of China (English)

    魏斌

    2015-01-01

    In order to satisfy the bridge deck pavement of asphalt concrete special performance re-quirements of asphalt binder,Improve the flexibility of bridge deck pavement asphalt concrete,by adding different proportions of rubber powder and SBS modified asphalt and composite mix performance test anal-ysis,discusses the composite rubber powder modified asphalt mixture by Sophie toughened,shear,impact mechanism water stability,and recommended significantly modified asphalt concrete composite best over-all performance rubber particles content.%为了满足桥面铺装沥青混凝土对沥青结合料的特殊性能要求,提高桥面铺装沥青混凝土的柔韧性,通过对不同掺加比例的橡胶粉与 SBS 复合改性沥青及其混合料的性能进行试验分析,探讨了橡胶粉对复合改性沥青混合料的增柔增韧、抗剪、水稳定性的影响机理,并推荐了可以显著复合改性沥青混凝土综合使用性能的最佳橡胶颗粒掺量。

  5. Asphalt Concrete Mixtures: Requirements with regard to Life Cycle Assessment

    OpenAIRE

    Jan Mikolaj; Frantisek Schlosser; Lubos Remek; Aurelia Chytcakova

    2015-01-01

    Design of asphalt concrete, required properties of constituent materials and their mixing ratios, is of tremendous significance and should be implemented with consideration given to the whole life cycle of those materials and the final construction. Conformity with requirements for long term performance of embedded materials is the general objective of the Life Cycle Assessment (LCA). Therefore, within the assessment, material properties need to be evaluated with consideration given to the wh...

  6. Untersuchungen zum spannungsabhängigen Materialverhalten von Asphalt

    OpenAIRE

    Zeissler, Alexander

    2015-01-01

    Mit dem Einzug numerischer Verfahren zur Dimensionierung von Verkehrskonstruktionen, im Speziellen für Asphaltbefestigung, werden charakteristische Materialkenngrößen benötigt. Des Weiteren wird mit der fortschreitenden Entwicklung von FEM-Programmen, die in Zusammenhang mit Strukturanalysen und Simulationsrechnungen ihren Einsatz finden, die Kenntnis detaillierter Materialkennwerte essentiell. Dass Asphalte mit ihrem charakteristischen Materialverhalten eine Temperatur- und Frequenzabhängigk...

  7. The Research on the Cracks of the Asphalt Pavement

    OpenAIRE

    OuYangZiqiang; Li Chunge

    2015-01-01

    The cracking is one of the common diseases of the asphalt pavement. According to the shape and the forming reasons, the cracks can be divided into two categories. Each categories can be divided into several types. Through the comparison and the analysis of the causes of different cracks, the prevention and the treatments are proposed in the respects of the structural design, material design and construction

  8. Utilization of Recycled Concrete Aggregates in Stone Mastic Asphalt Mixtures

    OpenAIRE

    Mohammad Saeed Pourtahmasb; Mohamed Rehan Karim

    2014-01-01

    Recycled concrete aggregate (RCA) is considered as one of the largest wastes in the entire world which is produced by demolishing concrete structures such as buildings, bridges, and dams. It is the intention of scientists and researchers, as well as people in authority, to explore waste material recycling for environmental and economic advantages. The current paper presents an experimental research on the feasibility of reusing RCA in stone mastic asphalt (SMA) mixtures as a partial replaceme...

  9. The Research on the Cracks of the Asphalt Pavement

    Directory of Open Access Journals (Sweden)

    OuYangZiqiang

    2015-07-01

    Full Text Available The cracking is one of the common diseases of the asphalt pavement. According to the shape and the forming reasons, the cracks can be divided into two categories. Each categories can be divided into several types. Through the comparison and the analysis of the causes of different cracks, the prevention and the treatments are proposed in the respects of the structural design, material design and construction

  10. Dynamic mechanical properties of asphalt cement using ultrasonic measurement

    International Nuclear Information System (INIS)

    This study measured the dynamic mechanical properties of asphalt cement, one of the viscoelastic materials, using the ultrasound. The wave speed and attenuation were measured from -20 degrees C to -60 degrees C at the frequency of 2.25 MHz. Then, the storage and loss longitudinal moduli, loss tangent, viscosity, storage and loss longitudinal compliance were found depending on the temperatures based on the linear viscoelastic theory.

  11. Structural Design of Asphalt Pavement for Low Cost Rural Roads

    Institute of Scientific and Technical Information of China (English)

    Yuan Goulin; Chen Rongshen

    2006-01-01

    On the basis of the equivalent axle load action frequency, the traffic classifications of rural roads as well as their corresponding types are classified. The asphalt pavement structure, road surface types and thickness of the rural roads are suggested for the various action frequency of the equivalent axle load. Furthermore, the roadbase thickness graphs are provided according to different equivalent axle load action frequency with different roadbed modulus and road surface modulus taken into account.

  12. INVESTIGATION OF ASPHALT PAVEMENT WITH ADDED CRUMB RUBBER

    OpenAIRE

    Mandula, Jan; Olexa, Tomaš; Holubka, Mariya; Salaiova, Brigita

    2014-01-01

    Waste tires must be recycled in environmentally safe ways that meet civil engineering concerns while fulfilling standards for construction materials. Used tires can be processed into rubber powders with particle sizes of 0–2 mm, a suitable fine aggregate for mixing into road pavements. We tested asphalt mixtures with rubber added using the dry method, comparing their properties with a traditional mixture. We tested asphalt–rubber mixtures with rubber incorporated at either ambient temperature...

  13. New experimental methods to monitor and characterize asphalt rubber binders

    OpenAIRE

    Peralta, J.; Silva, Hugo Manuel Ribeiro Dias da; Pais, Jorge C.

    2010-01-01

    The need for continuous quality improvement of the road pavements, leads to the development of new binders, such as asphalt rubber (AR). AR is produced by the digestion of crumb rubber from used tires on bitumen. The resulting AR is a heterogeneous material with high viscosity. The study of this product during its production is essential due to the sudden and sharp increase in the volume of AR in this phase. Knowledge of the extent of this phenomenon has obvious implications in...

  14. Improvement of the functional pavement quality with asphalt rubber mixtures

    OpenAIRE

    Fontes, Liseane P. T. L.; Pereira, Paulo A. A.; Pais, Jorge C.; Trichês, Glicério

    2006-01-01

    Skid resistance and texture are important safety characteristics which need to be considered in flexible pavement design, maintenance and rehabilitation. The main objective of this paper is to optimize surface texture characteristics in asphalt rubber pavements, mainly macrotexture to reduce splash, spray and hydroplaning and microtexture to increase friction at low and high speeds. The objective was accomplished by measuring the friction surface with two different tests: (i) B...

  15. Production technologies and analysis of use of rubberised asphalt

    OpenAIRE

    Pevec, Rok

    2013-01-01

    Used tires present a major enviormental problem worldwide since most of them are burned as fuel in the cement industry, but most of them lie illegally in landfills in nature. It is identified and confirmed in practice that the properties of bituminous binder, to which rubber particles, which are the product of recycling waste automobile and truck tires, are added, and consequently also the properties of asphalt mixtures are significantly improved. Research in this area and the ...

  16. Analyzing the influence of manufacturing conditions of reclaimed asphalt concrete on the characteristics of the asphalt binder: development of a gradual binder extraction method

    Science.gov (United States)

    Navaro, J.; Bruneau, D.; Drouadaine, I.; Pouteau, B.; Colin, J.; Dony, A.

    2012-05-01

    When asphalt concrete is manufactured incorporating a high percentage (almost 70%) of reclaimed materials from the deconstruction of road surfaces under renovation, and when the corresponding production device is designed specifically to reduce the energy input need (lowering the production temperature), the resulting manufacturing process contributes to the protection of the environment and reduces production costs. However, to meet the quality requirements of the finished product, virgin materials of appropriate quality and quantity must also be added (mineral aggregates and new asphalt binder) and control systems set up to quantify and optimize the parameters involved (thus avoiding the guess work which still often prevails today). It was for this reason that a new experimental technique described here was devised, which will ultimately be used in asphalt concrete production plants. The technique involves lixiviating reclaimed asphalt concrete using a chlorinated solvent; the resulting solute is collected gradually, then the mixture of binders (virgin and reclaimed asphalt concrete) can be characterized and their mass fractions quantified using a combination of UV and IR spectrometry. With this experimental technique we were able to assess the extent to which the reclaimed asphalt pavement binder participates in the agglomeration and cohesion of the reclaimed asphalt concrete. This assessment was made in terms of the main parameters in the production process, temperature of the materials and mixing time.

  17. Evidence of Multi-Stage Hydrocarbon Charging and Biodegradation of the Silurian Asphaltic Sandstones in the Tarim Basin, China

    Institute of Scientific and Technical Information of China (English)

    刘洛夫

    2002-01-01

    Asphalts distributed widely in the Silurian sandstones of the Tarim Basin include dry asphalt, soft asphalt and heavy oil. These asphaltic sandstones underwent multi-episodic sedimentary and tectonic events, and their occurrence is diverse and complex, being mixed with normal oil usually. So far, very little work has been done on the asphaltic sandstone origin and hydrocarbon charging ages. After detailed study on the Silurian sandstones, the following highlights were obtained from the analytical results: distribution of the mixed asphalt, heavy oil and normal oil in the Silurian sandstones is the result of multi-stage hydrocarbon charging from the Lower Paleozoic marine source rocks; the characters of asphalts formed from oils of different charging ages are of difference; the most important process constraining.the asphaltic sandstone origin is thought to be biodegradation.

  18. Influencing Factor Test on Rubber Powder Modified Asphalt%胶粉改性沥青影响因素试验

    Institute of Scientific and Technical Information of China (English)

    马韧

    2012-01-01

    研究分析了胶粉改性沥青的改性机理,并对几个关键的影响因素开展试验研究,试验结果与分析表明:拌和温度,胶粉细度和胶粉掺量对橡胶沥青的使用性能产生影响,并分别存在最佳的控制范围值.%Research and analysis of modification mechanism of rubber powder modified asphalt, and carry out experimental study in several key influence factors. Test results analysis and shows that stirring temperature, powder fineness and rubber powder content on rubber asphalt performance impact, which respectively exsit optimum control range.

  19. Experiment Research on Fatigue Property of Double-layer Asphalt Concrete Structure%双层式沥青路面结构极限强度的试验研究

    Institute of Scientific and Technical Information of China (English)

    吴金荣; 马芹永; 董晓红

    2012-01-01

    On the comprehensive action of. wheel load and natural factors, fatigue cracks are obvious on asphalt pavement. In order to improve fatigue life and using character of asphalt pavement, polyester fiber is mixed into asphalt concrete because its high strength, durable and light-weight. So based on double-layer asphalt concrete structure, its ultimate strength is researched on condition of various temperatures, fiber contents and asphalt-aggregate ratios. Change law of its ultimate strength is researched under different test conditions and its main influence factors are also obtained. This will provide a theoretical basis for further spread and application of asphalt pavement.%在车轮荷载和各种自然因素的综合作用下,沥青路面易产生疲劳开裂.为了提高沥青路面的疲劳寿命,将高强、耐久、轻质的聚酯纤维掺加到沥青混凝土中,以改善沥青路面的使用品质.因此,以双层式沥青路面结构为研究对象,研究双层式沥青路面结构在不同温度、不同纤维掺量和不同油石比条件下的极限强度,即在不同试验条件下的极限强度变化规律,根据试验结果得到影响双层式沥青路面结构极限强度的主要因素,为沥青路面的进一步推广应用提供理论依据.

  20. Thermal behavior of crumb-rubber modified asphalt concrete mixtures

    Science.gov (United States)

    Epps, Amy Louise

    Thermal cracking is one of the primary forms of distress in asphalt concrete pavements, resulting from either a single drop in temperature to an extreme low or from multiple temperature cycles above the fracture temperature of the asphalt-aggregate mixture. The first mode described is low temperature cracking; the second is thermal fatigue. The addition of crumb-rubber, manufactured from scrap tires, to the binder in asphalt concrete pavements has been suggested to minimize both types of thermal cracking. Four experiments were designed and completed to evaluate the thermal behavior of crumb-rubber modified (CRM) asphalt-aggregate mixtures. Modified and unmodified mixture response to thermal stresses was measured in four laboratory tests. The Thermal Stress Restrained Specimen Test (TSRST) and the Indirect Tensile Test (IDT) were used to compare mixture resistance to low temperature cracking. Modified mixtures showed improved performance, and cooling rate did not affect mixture resistance according to the statistical analysis. Therefore results from tests with faster rates can predict performance under slower field rates. In comparison, predicted fracture temperatures and stresses (IDT) were generally higher than measured values (TSRST). In addition, predicted fracture temperatures from binder test results demonstrated that binder testing alone is not sufficient to evaluate CRM mixtures. Thermal fatigue was explored in the third experiment using conventional load-induced fatigue tests with conditions selected to simulate daily temperature fluctuations. Test results indicated that thermal fatigue may contribute to transverse cracking in asphalt pavements. Both unmodified and modified mixtures had a finite capacity to withstand daily temperature fluctuations coupled with cold temperatures. Modified mixtures again exhibited improved performance. The fourth experiment examined fracture properties of modified and unmodified mixtures using a common fracture toughness test

  1. Study of normal and shear material properties for viscoelastic model of asphalt mixture by discrete element method

    DEFF Research Database (Denmark)

    Feng, Huan; Pettinari, Matteo; Stang, Henrik

    2015-01-01

    In this paper, the viscoelastic behavior of asphalt mixture was studied by using discrete element method. The dynamic properties of asphalt mixture were captured by implementing Burger’s contact model. Different ways of taking into account of the normal and shear material properties of asphalt mi...

  2. 77 FR 50651 - Approval and Promulgation of Air Quality Implementation Plans; New Hampshire; Hot Mix Asphalt Plants

    Science.gov (United States)

    2012-08-22

    ... Mix Asphalt Plants AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed rule. SUMMARY: EPA... Hampshire Hot Mix Asphalt Plant Rule at Env-A 2703.02(a). This rule establishes and requires limitations on visible emissions from all hot mix asphalt plants. This revision is consistent with the maintenance of...

  3. Damage detection and artificial healing of asphalt concrete after trafficking with a load simulator

    Science.gov (United States)

    Bueno, M.; Arraigada, M.; Partl, M. N.

    2016-08-01

    Artificial healing of asphalt concrete by induction heating requires the addition of electrically conductive and/or magnetic materials into the asphalt mixture. Hence, bitumen can be heated up by an alternating electromagnetic field, decreasing therefore its viscosity and allowing it to flow for closing cracks and recover bonding among the mineral aggregates.

  4. ENHANCING ASPHALT RHEOLOGICAL BEHAVIOR AND AGING SUSCEPTIBILITY USING BIO-CHAR AND NANO-CLAY

    Directory of Open Access Journals (Sweden)

    Renaldo C. Walters

    2014-01-01

    Full Text Available The life expectancy of Asphalt Binder (AB has been negatively impacted by the harsh bombardment of UV rays. UV rays cause asphalt to oxidize faster, which results in deterioration of asphalt rheological characteristics that can lead to pavement distresses. This study investigates the impact of bio-char and nano-clay of asphalt rheological properties. Two nano scale materials were used for this study were nano-clay and bio-char. Nano-clay (Cloisite 30B is a naturally occurring inorganic mineral. Bio-char is the waste product from bio-binder production. Bio-binder is produced from swine manure using a thermochemical conversion process. This process is then followed by a filtration procedure where the bio-char is produced. Chemical and physical properties of bio-char showed a significant presence of carbon which could in turn enhance asphalt flow properties and reduce the rate of asphalt oxidation. In this study several mixtures are designed and evaluated using Rotational Viscometer testing (RV and X-Ray Diffraction (XRD. Nano-clay is blended at 2 and 4% by weight, with and without bio-binder (5% by weight of dry mass. Bio-char is grinded to nano scale and added to the virgin asphalt binder (PG 64-22 at 2, 5 and 10% by weight. The study results showed that introduction of nano-clay could be effective in reducing temperature susceptibility of asphalt binder.

  5. Investigation of self healing behaviour of asphalt mixes using beam on elastic foundation setup

    NARCIS (Netherlands)

    Qiu, J.; Molenaar, A.A.A.; Van de Ven, M.F.C.; Wu, S.; Yu, J.

    2012-01-01

    Self healing of asphalt mixes is known for more than four decades. However, it is a complex phenomenon which depends on the duration of the rest period, temperature, crack size, etc. In order to quantify the self healing behaviour of asphalt mixes, a test setup was proposed in this research using an

  6. Study on triaxial test method and failure criterion of asphalt mixture

    Directory of Open Access Journals (Sweden)

    Jianlong Zheng

    2015-04-01

    Full Text Available Asphalt mixture is the most widely used pavement material all over the world. In China, more than 90% of service expressways are asphalt pavement. However, current asphalt pavement design method still has irrationality. Even though maximum tensile stress theory is used as failure criterion, pavement structure under the effects of wheel load is in three-dimensional complex stress state. Obviously, one-dimensional strength theory cannot reflect the failure characteristics and the resistance of pavement structure. So it is necessary to study the failure criterion of asphalt mixture under three-dimensional complex stress state. Due to limitations of test equipment, there are almost no studies in related area. Under this background, this paper develops a new triaxial test method, according to the investigation of strength characteristics of asphalt mixture under complex stress state through plane isobaric/axial tensile test, plane isobaric/axial compression test, plane tensile and compression/axial tensile test, to reveal the general rules of asphalt mixture's strength failure. The failure mode is divided into three types: tensile failure, shear failure and rheological failure. The tensile meridian and compression meridian in the stress space and strength envelope in the π plane where hydrostatic pressure is greater than zero are obtained, and the failure criterion of asphalt mixture under complex stress state is established, providing theoretical method and scientific basis for structure design as well as strength check of asphalt pavement under three-dimensional stress state.

  7. Influence of limestone fillers on combustion characteristics of asphalt mortar for pavements

    DEFF Research Database (Denmark)

    Ke, Wu; Kai, Zhu; Wu, Hao;

    2014-01-01

    Asphalt materials will be ignited and release significant toxic fumes within tunnel fires. Thus, combustion characteristics of asphalt materials used in road tunnel should be studied in order to limit such an adverse effect. In the present work we study the influence of limestone fillers on combu...

  8. 40 CFR Table 2 of Subpart Aaaaaaa... - Emission Limits for Asphalt Roofing Manufacturing (Coating) Operations

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Emission Limits for Asphalt Roofing Manufacturing (Coating) Operations 2 Table 2 of Subpart AAAAAAA of Part 63 Protection of Environment... AAAAAAA of Part 63—Emission Limits for Asphalt Roofing Manufacturing (Coating) Operations For * * *...

  9. Asphalt Pavement Aging and Temperature Dependent Properties Using Functionally Graded Viscoelastic Model

    Science.gov (United States)

    Dave, Eshan V.

    2009-01-01

    Asphalt concrete pavements are inherently graded viscoelastic structures. Oxidative aging of asphalt binder and temperature cycling due to climatic conditions being the major cause of non-homogeneity. Current pavement analysis and simulation procedures dwell on the use of layered approach to account for these non-homogeneities. The conventional…

  10. Determination of Required Energy Action at Formation of Asphalt Concrete Mixture

    OpenAIRE

    B. M. Khroustalev; V. N. Romaniuok

    2014-01-01

    A problem pertaining to determination of the concentrated exergy of the asphalt concrete mixture is considered in the paper. The paper shows the possibility to use the concentrated exergy of the asphalt concrete mixture for qualitative energy evaluation of mixing processes.

  11. 75 FR 12988 - National Emission Standards for Hazardous Air Pollutants for Area Sources: Asphalt Processing and...

    Science.gov (United States)

    2010-03-18

    ... the asphalt processing and asphalt roofing manufacturing area source category (74 FR 63236). Following... specified in Executive Order 13132, Federalism (64 FR 43255, August 10, 1999). This action does not..., Consultation and Coordination with Indian Tribal Governments (65 FR 67249, November 9, 2000). This...

  12. Distribution of radionuclides in the process of thermal decontamination of asphalt layers

    International Nuclear Information System (INIS)

    Autoradiographical analysis was used to investigate the radionuclides distribution in the process of thermal decontamination of asphalt. Cs-137 and Sr-90 were introduced in asphalt to simulate real contamination. It was found that penetration of these radionuclides is very small (about 1 mm). No significant emission of radionuclides was observed in the process of thermal decontamination

  13. Dynamic Mechanical Characterizations and Road Performances of Flame Retardant Asphalt Mortars and Concretes

    Institute of Scientific and Technical Information of China (English)

    QIN Xiantao; ZHU Siyue; LI Zuzhong; CHEN Shuanfa

    2015-01-01

    To research the dynamic mechanical properties and road performances of flame retardant asphalt mortars and mixtures, four different asphalt mortars/mixtures were prepared: a reference group and three asphalt mortars/mixtures containing composite lfame retardant materials (M-FRs) of different proportions. Temperature sweep, frequency sweep, repeated creep test, force ductility test and bending beam rheological test were carried out to research the dynamic mechanical properties of asphalt mortars containing M-FRs; wheel-tracking test, low-temperature bending test and freeze-thaw split test were used to study the road performances of asphalt mixtures containing M-FRs. The results show that high-temperature performances of the three lfame retardant asphalt mortars improve greatly, while low-temperature cracking resistances decline. Both high-temperature performances and water stabilities of asphalt mixtures containing M-FRs are quite good and exceed the speciifcation requirements. However, their low-temperature performances decline in different degrees. In summary, besides their good lfame retardancy, the lfame retardant asphalt mortars and mixtures also exhibit acceptable road performance.

  14. Road safety effects of porous asphalt: a systematic review of evaluation studies

    DEFF Research Database (Denmark)

    Elvik, R.; Greibe, Poul

    2005-01-01

    This paper presents a systematic review of studies that have evaluated the effects on road safety of porous asphalt. Porous asphalt is widely used on motorways in Europe, mainly in order to reduce traffic noise and increase road capacity. A meta-analysis was made of six studies, containing a total...... of eighteen estimates of the effect of porous asphalt on accident rates. No clear effect on road safety of porous asphalt was found. All summary estimates of effect indicated very small changes in accident rates and very few were statistically significant at conventional levels. Studies that have...... impact of these changes in risk factors on accident occurrence cannot be predicted. On the whole, the research that has been reported so far regarding road safety effects of porous asphalt is inconclusive. The studies are not of high quality and the findings are inconsistent....

  15. Hanford Permanent Isolation Barrier Program: Asphalt technology data and status report - FY 1994

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, H.D.; Romine, R.A.; Zacher, A.H.

    1994-09-01

    The asphalt layer within the Hanford Permanent Isolation Barrier (HPIB) is an important component of the overall design. This layer provides a RCRA equivalent backup to the overlying earthen layers in the unlikely event that these layers are not able to reduce the infiltration rate to less than 0.05 cm/yr. There is only limited amount of information on using asphalt for a moisture infiltration barrier over the long times required by the HPIB. Therefore, a number of activities are under way, as part of the Barrier Development Program, to obtain data on the performance of asphalt as a moisture barrier in a buried environment over a 1000-year period. These activities include (1) determining RCRA equivalency, (2) measurement of physical properties, (3) measurement of aging characteristics, and (4) relationship to ancient asphalt analogs. During FY 1994 progress was made on all of these activities. Studies were conducted both in the laboratory and on the prototype barrier constructed over the 216-B-57 crib in the 200 East Area on the Hanford Site. This report presents results obtained from the asphalt technology tasks during FY 1994. Also included are updates to planned activities for asphalt analogs and monitoring the asphalt test pad near the prototype barrier. Measurements of hydraulic conductivity on the HMAC portion of the prototype barrier show that the asphalt layers easily meet the RCRA standard of 1 {times} 10{sup -7} cm/s. In-place measurements using a new field falling head technique show an average of 3.66 {times} 10{sup -8} cm/s, while cores taken from the north end of the prototype and measured in a laboratory setup averaged 1.29 {times} 10{sup -9} cm/s. Measurements made on the fluid applied asphalt membrane (polymer-modified asphalt) show an extremely low permeability of less than 1 {times} 10{sup -11} cm/s.

  16. Evaluation of an eastern shale oil residue as an asphalt additive

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, K.P.; Harnsberger, P.M.

    1995-09-01

    An evaluation of eastern shale oil (ESO) residue as an asphalt additive to reduce oxidative age hardening and moisture susceptibility was conducted by Western Research Institute (WRI). The ESO residue, have a viscosity of 23.9 Pa{lg_bullet}s at 60{degree}C (140{degree}F), was blended with three different petroleum-derived asphalts, ASD-1, AAK-1, and AAM-1, which are known to be very susceptible to oxidative aging. Rheological and infrared analyses of the unaged and aged asphalts and the blends were then conducted to evaluate oxidative age hardening. In addition, the petroleum-derived asphalts and the blends were coated onto three different aggregates, Lithonia granite (RA), a low-absorption limestone (RD), and a siliceous Gulf Coast gravel (RL), and compacted into briquettes. Successive freeze-thaw cycling was then conducted to evaluate the moisture susceptibility of the prepared briquettes. The rheological analyses of the unaged petroleum-derived asphalts and their respective blends indicate that the samples satisfy the rutting requirement. However, the aging indexes for the rolling thin film oven (RTFO)-aged and RTFO/pressure aging vessel (PAV)-aged samples indicate that the blends are stiffer than the petroleum-derived asphalts. This means that when in service the blends will be more prone to pavement embrittlement and fatigue cracking than the petroleum-derived asphalts. Infrared analyses were also conducted on the three petroleum-derived asphalts and the blends before and after RTFO/PAV aging. In general, upon RTFO/PAV aging, the amounts of carbonyls and sulfoxides in the samples increase, indicating that the addition of the ESO residue does not mitigate the chemical aging (oxidation) of the petroleum-derived asphalts. This information correlates with the rheological data and the aging indexes that were calculated for the petroleum-derived asphalts and the blends.

  17. Hanford Permanent Isolation Barrier Program: Asphalt technology data and status report - FY 1994

    International Nuclear Information System (INIS)

    The asphalt layer within the Hanford Permanent Isolation Barrier (HPIB) is an important component of the overall design. This layer provides a RCRA equivalent backup to the overlying earthen layers in the unlikely event that these layers are not able to reduce the infiltration rate to less than 0.05 cm/yr. There is only limited amount of information on using asphalt for a moisture infiltration barrier over the long times required by the HPIB. Therefore, a number of activities are under way, as part of the Barrier Development Program, to obtain data on the performance of asphalt as a moisture barrier in a buried environment over a 1000-year period. These activities include (1) determining RCRA equivalency, (2) measurement of physical properties, (3) measurement of aging characteristics, and (4) relationship to ancient asphalt analogs. During FY 1994 progress was made on all of these activities. Studies were conducted both in the laboratory and on the prototype barrier constructed over the 216-B-57 crib in the 200 East Area on the Hanford Site. This report presents results obtained from the asphalt technology tasks during FY 1994. Also included are updates to planned activities for asphalt analogs and monitoring the asphalt test pad near the prototype barrier. Measurements of hydraulic conductivity on the HMAC portion of the prototype barrier show that the asphalt layers easily meet the RCRA standard of 1 x 10-7 cm/s. In-place measurements using a new field falling head technique show an average of 3.66 x 10-8 cm/s, while cores taken from the north end of the prototype and measured in a laboratory setup averaged 1.29 x 10-9 cm/s. Measurements made on the fluid applied asphalt membrane (polymer-modified asphalt) show an extremely low permeability of less than 1 x 10-11 cm/s

  18. Recent rubber crumb asphalt pavement projects in Alberta

    Energy Technology Data Exchange (ETDEWEB)

    Soleyman, H.R. [Alberta Univ., Edmonton, AB (Canada). Dept. of Civil and Environmental Engineering; Pulles, B.C.M.; Treleaven, L.B. [EBA Engineering Consultants Ltd., Edmonton, AB (Canada)

    2003-07-01

    Several countries around the world have been using rubber crumb (RC) for pavement applications for more than 20 years. The performance of asphalt pavements is enhanced by the use of recycled tires, which has the added advantage of solving the problem of tire disposal. In 2002, the Tire Recycling Management Association of Alberta (TRMA) and Alberta Transportation (AT) evaluated the feasibility and performance of an overlay using asphalt rubber (AR) pavement in Alberta. A partnership in the project was formed by AT, the City of Calgary, the City of Edmonton, and Strathcona County, where each one paved one section of a road with AR in conjunction with a section using conventional or other asphalt mixture types. The roads selected were: (1) 112 Avenue North West in Calgary, (2) 17 Street and Baseline Road in Strathcona County, (3) 137 Avenue in Edmonton, and (4) highway 630 in the vicinity of North Cooking Lake (Alberta Transportation). Two different AR pavement thicknesses were used to study the effects of overlay thicknesses on the performance of the overlay. The structural and functional factors were monitored before, during and after the construction of all sections. The preliminary evaluation of the application of AR in Alberta was presented, along with a summary of test results and performances of AR pavement sections. A full freeze-thaw cycle is required (Spring 2003) before the results of the analysis of the testing are known. The reduced thickness AR sections performed in a similar manner to those with full thickness AC sections. 10 refs., 5 tabs., 3 figs.

  19. Effect of Short-Term Aging Process on the Moisture Susceptibility of Asphalt Mixtures and Binders Containing Sasobit Warm Mix Additive

    OpenAIRE

    Bo Li; Jinyu Yang; Xiaohui Li; Xiang Liu; Feng Han; Liangying Li

    2015-01-01

    Moisture susceptibility is one of the key issues of warm mix asphalt (WMA). In this research, the moisture susceptibility of asphalt mixtures and binders containing Sasobit warm mix additive was investigated in comparison to that of hot mixture asphalt (HMA) through laboratory aging experiments. The WMA asphalt mixtures were aged in the laboratory at three aging temperatures and times. The moisture susceptibility of the asphalt mixtures was measured through the laboratory immersed Marshall te...

  20. Analysis of the Influence of the Modernized Bitumen Batching System on the Composition of the Hot Mix Asphalt Mixture

    Directory of Open Access Journals (Sweden)

    Justas Bražiūnas

    2011-04-01

    Full Text Available The weighted mass of a binder in the bucket of the bitumen batcher of a batch-type asphalt plant should be such that its percentage of hot mix asphalt (HMA mixture lot would comply with the design amount of the job-mix formula in all mix batches. A bitumen batcher does not always weigh bitumen portions precisely. Their mass deviations from the amount determined by the project and its variation impair HMA composition and performance. The paper provides data on a statistical evaluation of bitumen batcher modernization performed at Lithuanian enterprise „LL“. The article analyzes differences in the structures of reconstructed and not reconstructed bitumen batching systems and presents methods for determining modernization effectiveness. The paper also focuses on the effectiveness of the batching system, determining deviations from bitumen content in subsamples taken and extracted everyday during two seasons (before and after batcher‘s modernization of producing HMA from the value of job-mix formula and comparing them to the values of tolerances.Article in Lithuanian

  1. Microstructural characterization of the chemomechanical behavior of asphalt in terms of aging and fatigue performance properties

    Science.gov (United States)

    Allen, Robert Grover

    The study of asphalt chemo-mechanics requires a basic understanding of the physical properties and chemical composition of asphalt and how these properties are linked to changes in performance induced by chemical modifications. This work uniquely implements the framework of chemo-mechanics by investigating two types of chemical modification processes, natural (oxidative aging) and synthetic (chemical doping) as they relate not only to macro-scale properties of asphalt binder but also to the asphalt microstructure and nanorheology. Furthermore, this study demonstrates the application of atomic force microscopy (AFM) imaging and the extraction of nano-scale engineering properties, i.e. elastic modulus, relaxation modulus, and surface energy, as a method to predict performance related to the fatigue characteristics of asphalt binders by modeling intrinsic material flaws present amongst phase interfaces. It was revealed that oxidative aging induces substantial microstructural changes in asphalt, including variations in phase structure, phase properties, and phase distribution. It has also been shown that certain asphalt chemical parameters have a consistent and measureable effect on the asphalt microstructure that is observed with AFM. In fact, particular phases that emerged via chemical doping revealed a surprising correlation between oxidative aging and the saturates chemical parameter of asphalt in terms of how they explicitly impact durability and performance of asphalt. By implementing a crack initiation model---which requires measureable microstructural characteristics as an input parameter---it was found that microstructural flaws (depending on the extremity) can have a more profound impact on asphalt performance than the properties of the material located between the flaws. It was also discovered by comparing the findings to performance data in the Strategic Highway Research Program's (SHRP's) Materials Reference Library (MRL), that the crack initiation model

  2. New approach for calculating permanent deformation in asphalt pavement

    Institute of Scientific and Technical Information of China (English)

    TAN Yi-qiu; CHEN Feng-chen; LIU Hao; SU Xin; DONG Ze-jiao; DONG Yu-ming

    2010-01-01

    A new approach using the Fiber Bragg Grating(FBG)sensor and viscoelastic model to monitor and analyze the internal strain and temperature of asphalt pavement is proposed.Some parameters including peak strain,temperature and loading time were calculated with the application of multi-dimensional sensors group.These parameters were incorporated with viscoelastic model of five units to evaluate the permanent deformation of pavement.An application example was conducted,and the results show that it is feasible to analyze and calculate the permanent deformation of pavement structures with FBG sensors.

  3. Mathematical Approach in Rheological Characterizing of Asphalt Emulsion Residues

    OpenAIRE

    2015-01-01

    Three different emulsion residues, such as SS1HP, HFE90, and SS-1VH (trackless), and a base asphalt binder (PG 64-22) are compared to characterize rheological properties by using DSR test. In order to capture the emulsion properties, different frequencies (from 1 to 100 rad/sec at a 10% constant shear rate) and temperatures (from −45°C to 75°C with 15°C increments) were applied. Then, a master curve for shear modulus was plotted for each emulsion. The transition of the HFE90 emulsion from vis...

  4. Viscoelastic Property Evaluation of Asphalt Cement by Ultrasonic Measurement

    International Nuclear Information System (INIS)

    This study investigates the method to measure the viscoelastic properties of asphalt cement, one of the viscoelastic materials, using the ultrasound. The wave speed and attenuation were measured from -20 .deg. C to 60 .deg. C at the frequency of 2.25MHz. Then, the storage and loss longitudinal moduli, loss tangent storage and loss longitudinal compliances were found depending on the temperatures based on the linear viscoelastic theory. Stress relaxation, creep, and viscosity were predicted using Maxwell and Voigt-Kelvin viscoelastic models. The validity of superposition principle and shift factor were verified by comparing the present results to the data reported in the literatures

  5. Analysis of moisture susceptibility of different loose coated asphalt mixtures

    International Nuclear Information System (INIS)

    The durability is one of the significant properties of bituminous paving mixtures. It is shown that moisture damage is one of the primary factors affecting the durability of the mixtures. Moisture damage is basically a combined result of two mechanisms: a) Loss of adhesion between the bitumen and aggregate interface and b) Loss of cohesion in the mixture along with several other factors like the changes in binders, aggregates qualities and something else. The aim of this study is therefore to examine the moisture sensitivity, of different combinations of five different kinds of aggregate quarries/sources and six binder types of different penetration grade and properties, and compare the performance of these combinations between four laboratory tests: Static Immersion Test, Total Water Immersion Test (TWIT) Test, Boiling TWIT Test and Rolling Bottle Test. The tests have been carried out at the Taxila Institute of Transportation Engineering (TITE) to obtain the data for loose coated bituminous paving mixtures. The results show that the combination of Margallah aggregate source and ELVALOY Polymer Modified Bitumen provides best resistance against moisture damage and Rolling Bottle Test is the best test to discriminate between different loose coated Asphalt mixtures, irrespective of time taken by the test. major factors that caused moisture-related problems: adhesive failure, bitumen stripping off the aggregate surface and cohesive failure which is due to the loss of mixture stiffness. Moisture-related problems do not occur without the presence of water and traffic, which provides energy to break the adhesive bonds and cause cohesive failures. Repeated freeze-thaw cycles can also accelerate the distress in the pavement. Since the performance of Asphalt mixtures under the affect of moisture is a very complex issue, various researches have been made to simulate the moisture damage in the past years. Asphalt technologists have carried out many attempts to develop

  6. Mezclas SMA (Stone Mastic Asphalt) con alto contenido de ligante

    OpenAIRE

    Costa, Andrés; Cervantes, Rocío; Loma, Javier; Hidalgo, María Elena; Hergueta, José Antonio; Sánchez, Fernando; Lanchas, Santiago; Núñez, Ruy; Rubio, Baltasar; Jiménez, Rafael; Pérez Jiménez, Félix Edmundo; Botella Nieto, Ramón; Expósito, Santiago; Fernández, Victoriano; Potti, Juan José

    2013-01-01

    Las denominadas mezclas bituminosas en caliente SMA (Stone Mastic Asphalt) están recogidas en la normativa UNE EN 13108-5 y aunque en España apenas se han utilizado, su uso esta extendido por todo el mundo. Un grupo de empresas y algunos centros de investigación españoles, estamos desarrollando un proyecto de investigación denominado: Mezclas SMA de la familia de la norma UNE EN 13108-5 que sean Sostenibles y Medioambientalmente Amigables. Financiado por el Centro Tecnológico para el Desarrol...

  7. Relationship Between Aging Performance and Chemical Composition of Asphalt%石油沥青老化性能与其化学组成的关系新探讨

    Institute of Scientific and Technical Information of China (English)

    林璐; 李晓林; 郑广宇; 张立群

    2013-01-01

    The hot oxygen aging of four kinds of asphalts were carried on rotated thin film oven tests (RTFOT) to characterize basic performance of asphalts before and after aging,and the relationship between aging performance and chemical composition were discussed in detail.It was found that the increase of viscosity was not exponential or linear which were traditionally regarded as,but linear first and accelerated then,and the point of transition was related to asphalt grades.The colloidal instability index (L) was closely associated with aging performance of asphalts,and the higher Ic gave rise to greater change before and after aging.The softening point and viscosity of asphalts were related to number-average molecular weight and colloidal state,and the variations of penetration and ductility had well relationship to light components inside asphalts.The aging process of asphalts was influenced by the content of elemental sulfur,and more content of elemental sulfur caused smaller change of penetration before and after aging.%采用旋转薄膜加热老化试验(RTFOT),对4种不同牌号的沥青进行了热氧老化模拟,对沥青老化前后的各项基本性能进行了表征,并对其老化性能与化学组成之间的关系进行了详细探讨.结果表明,沥青老化过程中,黏度的增长并非传统意义上人们认为的呈指数型或直线型增长,而是先直线增长,到达某一临界点后增长速率加快,且临界点与沥青种类有关.胶体不稳定指数Ix与沥青的老化性能存在密切关联,Ix越大的沥青,老化后性能变化越大.沥青的软化点与黏度都与沥青的数均分子量及胶体结构有关,而针入度与延度的变化则与沥青中轻组分的关系较密切.S元素含量影响沥青的老化过程,S含量大的沥青,老化前后针入度变化小.

  8. Development of high stability hot mix asphalt concrete with hybrid binder

    Directory of Open Access Journals (Sweden)

    Toshiaki Hirato

    2014-12-01

    Full Text Available Cost reduction of public works projects has been desired due to severe financial circumstances. Therefore, asphalt pavement has been requested to extend its life. Semi-flexible pavement or epoxy asphalt pavement, which has high rutting resistance and oil resistance, may be applied to the place where these performances ae demanded. However, special technique is required in manufacturing and construction. In addition, these materials have also raised a problem that they cannot be recycled. Meanwhile, conventional asphalt pavement has several drawbacks. It is vulnerable to rutting caused by traffic load and damage caused by petroleum oils such as gasoline or motor oil. The materials used in asphalt mixtures were studied for improving the durability of asphalt mixture. A high stability asphalt concrete was developed which has equal or superior performance to semi-flexible pavement and epoxy asphalt pavement. In this paper, the process of selecting the substance and the characteristics evaluation of the developed mixtures ae described. Furthermore, an inspection result as well as follow-up survey of the performance of the developed mixtures obtained from trial and actual construction is shown.

  9. Caltrans use of scrap tires in asphalt rubber products: a comprehensive review

    Directory of Open Access Journals (Sweden)

    Haiping Zhou

    2014-02-01

    Full Text Available The California Department of Transportation (Caltrans has been using scrap tire rubber in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized hot mix asphalt(RHMA. Both the wet (field blend and dry processes were used in early trials. Caltrans has also used rubber modified binders containing both crumb rubber modifier and polymer modifier that could be manufactured at a refinery facility, a terminal blend wet process. Since the beginning of this century, Caltrans increased the use of scrap tire rubber in paving projects and invested considerable resources in developing technically sound, cost effective, and environmentally friendly strategies for using scrap tire rubber in roadway applications. By the end of year 2010, approximately 31%of all hot mix asphalt (HMA placed by Caltrans was rubberized HMA, roughly 1.2 million tons. Caltrans efforts in using asphalt rubber products were also demonstrated in its research and technology development. These included the construction of two full-scale field experiments, five warranty projects, and an accelerated pavement study using a heavy vehicle simulator. Additionally, terminal blend asphalt rubber and rubberized warm mix asphalts began to be experimented on trial basis. This paper provides a comprehensive review of Caltrans experience over four decades with asphalt rubber products. Current practices and future outlook are also discussed.

  10. LABORATORY SIMULATION OF POROUS ASPHALT PARKING LOT SYSTEM AND MIX DESIGN FOR STORM WATER MANAGEMENT

    Directory of Open Access Journals (Sweden)

    M. O. HAMZAH

    2013-04-01

    Full Text Available Porous asphalt pavement was initially developed for the purpose of improving road safety, best candidate material for quiet pavement and to avoid aquaplaning and skidding in wet weather. However, from previous studies, porous asphalt is able to mitigate surface runoff. Porous asphalt parking lots with underlying reservoir course perform as additional temporary water storage matrix that enables reduction of flash flood. This paper elaborates the development of a new porous asphalt aggregate grading design for storm water mitigation using the Nominal Maximum Aggregate Size (NMAS 20 mm. The properties of the mixes were quantified and evaluated in terms of air voids, permeability, abrasion loss and indirect tensile strength. It was found that the proposed gradation has the best permeability and Indirect Tensile Strength (ITS values when compacted at 50 blows per face with a standard Marshal compactor. The porous asphalt slab was prepared using a slab compactor to simulate porous parking lot paving at site. The porous asphalt slab was finally placed inside a locally fabricated water flow simulator to simulate a porous asphalt pavement system for parking lots.

  11. Use of Hydrogen from Renewable Energy Source for Powering Hot-Mix Asphalt Plant

    Directory of Open Access Journals (Sweden)

    Kasthurirangan Gopalakrishnan

    2012-03-01

    Full Text Available A significant portion of paved roads and highways are surfaced with Hot-Mix Asphalt. Environmental Life-Cycle Assessment studies have shown that, in the production of Hot-Mix Asphalt pavements, major consumption of energy takes place during asphalt mixing and drying of aggregates, more than what is consumed during the extraction of crude oil and the distillation of bitumen. Currently, natural gas is the primarily source of fossil fuel used to produce 70 to 90 percent of the Hot-Mix Asphalt in the USA, while the remainder of the Hot-Mix Asphalt is produced using oil, propane, waste oil, or other fuels. Energy-related CO2 emissions resulting from the use of fossil fuels in various industry and transportation sectors represent a significant portion of human-made greenhouse gas emissions. This study investigates the technical feasibility of using a hybrid wind energy system as a clean source of energy for operating an entire Hot-Mix Asphalt production facility. Since wind blows intermittently, the extracted wind energy will be stored in the form of hydrogen which is considered a lightweight, compact energy carrier, for later use, thus creating a ready source of electricity for the Hot-Mix Asphalt plant when wind is not present or when electricity demand is high.

  12. Rutting and Fatigue Cracking Resistance of Waste Cooking Oil Modified Trinidad Asphaltic Materials

    Directory of Open Access Journals (Sweden)

    Rean Maharaj

    2015-01-01

    Full Text Available The influence of waste cooking oil (WCO on the performance characteristics of asphaltic materials indigenous to Trinidad, namely, Trinidad Lake Asphalt (TLA, Trinidad Petroleum Bitumen (TPB, and TLA : TPB (50 : 50 blend, was investigated to deduce the applicability of the WCO as a performance enhancer for the base asphalt. The rheological properties of complex modulus (G∗ and phase angle (δ were measured for modified base asphalt blends containing up to 10% WCO. The results of rheology studies demonstrated that the incremental addition of WCO to the three parent binders resulted in incremental decreases in the rutting resistance (decrease in G∗/sinδ values and increases in the fatigue cracking resistance (decrease in G∗sinδ value. The fatigue cracking resistance and rutting resistance for the TLA : TPB (50 : 50 blends were between those of the blends containing pure TLA and TPB. As operating temperature increased, an increase in the resistance to fatigue cracking and a decrease in the rutting resistance were observed for all of the WCO modified asphaltic blends. This study demonstrated the capability to create customized asphalt-WCO blends to suit special applications and highlights the potential for WCO to be used as an environmentally attractive option for improving the use of Trinidad asphaltic materials.

  13. Greenhouse Gas Emissions from Asphalt Pavement Construction: A Case Study in China.

    Science.gov (United States)

    Ma, Feng; Sha, Aimin; Lin, Ruiyu; Huang, Yue; Wang, Chao

    2016-03-01

    In China, the construction of asphalt pavement has a significant impact on the environment, and energy use and greenhouse gas (GHG) emissions from asphalt pavement construction have been receiving increasing attention in recent years. At present, there is no universal criterion for the evaluation of GHG emissions in asphalt pavement construction. This paper proposes to define the system boundaries for GHG emissions from asphalt pavement by using a process-based life cycle assessment method. A method for evaluating GHG emissions from asphalt pavement construction is suggested. The paper reports a case study of GHG emissions from a typical asphalt pavement construction project in China. The results show that the greenhouse gas emissions from the mixture mixing phase are the highest, and account for about 54% of the total amount. The second highest GHG emission phase is the production of raw materials. For GHG emissions of cement stabilized base/subbase, the production of raw materials emits the most, about 98%. The GHG emission for cement production alone is about 92%. The results indicate that any measures to reduce GHG emissions from asphalt pavement construction should be focused on the raw materials manufacturing stage. If the raw materials production phase is excluded, the measures to reduce GHG emissions should be aimed at the mixture mixing phase. PMID:27011196

  14. Research on nonlinear constitutive relationship of permanent deformation in asphalt pavements

    Institute of Scientific and Technical Information of China (English)

    PENG; Miaojuan; XU; Zhihong

    2006-01-01

    To predict correctly the rut depths in asphalt pavements,a new nonlinear viscoelastic-elastoplastic constitutive model of permanent deformation in asphalt pavements is presented.The model combines a generalized Maxwell model with an elastoplastic one.Then from the creep theory,the linear and nonlinear constitutive equations of the generalized Maxwell model are obtained.From the nonlinear finite element method for the rutting of the asphalt pavement,the rut depths of 4 asphalt-aggregate mixtures are obtained.And the results are compared with the ones from the finite element method by SHRP and the experiments by SWK/UN.The results in this paper are better than the ones by SHRP,and agree with the ones of the experiment by SWK/UN.This shows that the nonlinear viscoelastic-elastoplastic constitutive model,which is presented in this paper for the rutting of the asphalt pavement,is effective.The properties,such as nonlinear elasticity,plasticity,viscoelasticity and nonlinear viscoelasticity,which affect the rutting of an asphalt pavement,can be shown in the model.And the characteristics of the permanent deformation of the asphalt pavement can be presented entirely in the model.

  15. The Potential of Heat Collection from Solar Radiation in Asphalt Solar Collectors in Malaysia

    Science.gov (United States)

    Beddu, Salmia; Talib, Siti Hidayah Abdul; Itam, Zarina

    2016-03-01

    The implementation of asphalt solar collectors as a means of an energy source is being widely studied in recent years. Asphalt pavements are exposed to daily solar radiation, and are capable of reaching up to 70°C in temperature. The potential of harvesting energy from solar pavements as an alternative energy source in replace of non-renewable energy sources prone to depletion such as fuel is promising. In Malaysia, the sun intensity is quite high and for this reason, absorbing the heat from sun radiation, and then utilizing it in many other applications such as generating electricity could definitely be impressive. Previous researches on the different methods of studying the effect of heat absorption caused by solar radiation prove to be quite old and inaffective. More recent findings, on the otherhand, prove to be more informative. This paper focuses on determining the potential of heat collection from solar radiation in asphalt solar collectors using steel piping. The asphalt solar collector model constructed for this research was prepared in the civil engineering laboratory. The hot mixed asphalt (HMA) contains 10% bitumen mixed with 90% aggregates of the total size of asphalt. Three stainless steel pipes were embedded into the interior region of the model according to the design criteria, and then put to test. Results show that harvesting energy from asphalt solar collectors proves highly potential in Malaysia due its the hot climate.

  16. Glass Transition and Molecular Mobility in Styrene-Butadiene Rubber Modified Asphalt.

    Science.gov (United States)

    Khabaz, Fardin; Khare, Rajesh

    2015-11-01

    Asphalt, a soft matter consisting of more than a thousand chemical species, is of vital importance for the transportation infrastructure, yet it poses significant challenges for microscopic theory and modeling approaches due to its multicomponent nature. Polymeric additives can potentially enhance the thermo-mechanical properties of asphalt, thus helping reduce the road repair costs; rational design of such systems requires knowledge of the molecular structure and dynamics of these systems. We have used molecular dynamics (MD) simulations to investigate the volumetric, structural, and dynamic properties of the neat asphalt as well as styrene-butadiene rubber (SBR) modified asphalt systems. The volume-temperature behavior of the asphalt systems exhibited a glass transition phenomenon, akin to that observed in experiments. The glass transition temperature, room temperature density, and coefficient of volume thermal expansion of the neat asphalt systems so evaluated were in agreement with experimental data when the effect of the high cooling rate used in simulations was accounted for. While the volumetric properties of SBR modified asphalt were found to be insensitive to the presence of the SBR additive, the addition of SBR led to an increase in the aggregation of asphaltene molecules. Furthermore, addition of SBR caused a reduction in the mobility of the constituent molecules of asphalt, with the reduction being more significant for the larger constituent molecules. Similar to other glass forming liquids, the reciprocal of the diffusion coefficient of the selected molecules was observed to follow the Vogel-Fulcher-Tammann (VFT) behavior as a function of temperature. These results suggest the potential for using polymeric additives for enhancing the dynamic mechanical properties of asphalt without affecting its volumetric properties. PMID:26451630

  17. A review of changes in composition of hot mix asphalt in the United States.

    Science.gov (United States)

    Mundt, Diane J; Marano, Kristin M; Nunes, Anthony P; Adams, Robert C

    2009-11-01

    This review researched the materials, methods, and practices in the hot mix asphalt industry that might impact future exposure assessments and epidemiologic research on road paving workers. Since World War II, the U.S. interstate highway system, increased traffic volume, transportation speeds, and vehicle axle loads have necessitated an increase in demand for hot mix asphalt for road construction and maintenance, while requiring a consistent road paving product that meets state-specific physical performance specifications. We reviewed typical practices in hot mix asphalt paving in the United States to understand the extent to which materials are and have been added to hot mix asphalt to meet specifications and how changes in practices and technology could affect evaluation of worker exposures for future research. Historical documents were reviewed, and industry experts from 16 states were interviewed to obtain relevant information on industry practices. Participants from all states reported additive use, with most being less than 2% by weight. Crumb rubber and recycled asphalt pavement were added in concentrations approximately 10% per unit weight of the mix. The most frequently added materials included polymers and anti-stripping agents. Crumb rubber, sulfur, asbestos, roofing shingles, slag, or fly ash have been used in limited amounts for short periods of time or in limited geographic areas. No state reported using coal tar as an additive to hot mix asphalt or as a binder alternative in hot mix pavements for high-volume road construction. Coal tar may be present in recycled asphalt pavement from historical use, which would need to be considered in future exposure assessments of pavers. Changes in hot mix asphalt production and laydown emission control equipment have been universally implemented over time as the technology has become available to reduce potential worker exposures. This work is a companion review to a study undertaken in the petroleum refining

  18. How to transform an asphalt concrete pavement into a solar turbine

    International Nuclear Information System (INIS)

    Highlights: • We create a system for harvesting energy from asphalt concrete. • We create an artificial porosity in the asphalt concrete. • We connect a chimney to this porosity. • Differences in temperature produce an air flow. • This air flow serves also for cooling down the pavement. - Abstract: Asphalt concrete can absorb a considerable amount of the incident solar radiation. For this reason asphalt roads could be used as solar collectors. There have been different attempts to achieve this goal. All of them have been done by integrating pipes conducting liquid, through the structure of the asphalt concrete. The problem of this system is that all pipes need to be interconnected: if one is broken, the liquid will come out and damage the asphalt concrete. To overcome these limitations, in this article, an alternative concept is proposed:parallel air conduits, where air can circulate will be integrated in the pavement structure. The idea is to connect these artificial pore volumes in the pavement to an updraft or to a downdraft chimney. Differences of temperature between the pavement and the environment can be used to create an air flow, which would allow wind turbines to produce an amount of energy and that would cool the pavement down in summer or even warm it up in winter. To demonstrate that this is possible, an asphalt concrete prototype has been created and basics calculations on the parameters affecting the system have been done. It has been found that different temperatures, volumes of air inside the asphalt and the difference of temperature between the asphalt concrete and the environment are critical to maximize the air flow through the pavement. Moreover, it has been found that this system can be also used to reduce the heat island effect

  19. Distribution characteristics and petroleum geological significance of the Silurian asphaltic sandstones in Tarim Basin

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Jun; PANG; Xiongqi; LIU; Luofu; JIANG; Zhenxue; LIU

    2004-01-01

    The Tarim Basin is a typical superimposed basin in which there have occurred multiphase adjustment and destruction of the reservoirs. The widely distributed asphaltic sandstones of the Silurian are the very product after destruction of the reservoirs. Studies show that the Silurian asphaltic sandstones distributed in both the middle and western parts on the basin are controlled chiefly by the Caledonian oil source area and by the Tazhong, Tabei and Bachu uplifts, whereas the distribution of the asphaltic sandstones on local structural belts is controlled by the reservoir's sedimentary system. Vertically, most of the asphaltic sandstones are under the regional caprock of red mudstones and the upper sandstone section of compact lithology. Due to the difference of hydrocarbon destruction in the early stage and the influence of hydrocarbon recharge in the late stage, the asphaltic sandstones and oil-bearing sandstones in the Tazhong area can be vertically divided into the upper and lower sections and they have an interactive distribution relationship as well. Asphaltic sandstones exist not only in intergranular pores but also inside the grains of sand and between the crevices, proving the destruction of early reservoirs due to uplifting. The existence of asphaltic sandstones over a large area reveals that the large-scale migration and accumulation and the subsequent destruction of hydrocarbons in the Craton area. The destruction caused a loss of the reserve resources of the Palaeozoic amounting to nearly 13.3 billion tons. Asphaltic sandstones formed after the destruction of oil and gas may serve as an effective caprock which is beneficial to accumulation of hydrocarbons and formation of the pool sealed by asphaltic sandstones in the later stage. The destruction of the early Silurian hydrocarbons depends on the stratigraphic burial depth. The deep part under the northern slope of Tazhong is an area favorable to search of undestroyed Silurian oil reservoirs.

  20. Leachability of dissolved chromium in asphalt and concrete surfacing materials.

    Science.gov (United States)

    Kayhanian, Masoud; Vichare, Akshay; Green, Peter G; Harvey, John

    2009-08-01

    Leachate metal pollutant concentrations produced from different asphalt and concrete pavement surfacing materials were measured under controlled laboratory conditions. The results showed that, in general, the concentrations of most metal pollutants were below the reporting limits. However, dissolved chromium was detected in leachate from concrete (but not asphalt) specimens and more strongly in the early-time leachate samples. As the leaching continued, the concentration of Cr decreased to below or close to the reporting limit. The source of the chromium in concrete pavement was found to be cement. The concentration of total Cr produced from leachate of different cement coming from different sources that was purchased from retail distributors ranged from 124 to 641mug/L. This result indicates that the potential leachability of dissolved Cr from concrete pavement materials can be reduced through source control. The results also showed that the leachability of dissolved Cr in hardened pavement materials was substantially reduced. For example, the concentration of dissolved Cr measured in actual highway runoff was found to be much lower than the Cr concentration produced from leachate of both open and dense graded concrete pavement specimens under controlled laboratory study. It was concluded that pavement materials are not the source of pollutants of concern in roadway runoff; rather most pollutants in roadway surface runoff are generated from other road-use or land-use sources, or from (wet or dry) atmospheric deposition. PMID:19604624