WorldWideScience

Sample records for asme code

  1. ASME Code Efforts Supporting HTGRs

    Energy Technology Data Exchange (ETDEWEB)

    D.K. Morton

    2010-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  2. ASME Code Efforts Supporting HTGRs

    Energy Technology Data Exchange (ETDEWEB)

    D.K. Morton

    2011-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  3. ASME Code Efforts Supporting HTGRs

    Energy Technology Data Exchange (ETDEWEB)

    D.K. Morton

    2012-09-01

    In 1999, an international collaborative initiative for the development of advanced (Generation IV) reactors was started. The idea behind this effort was to bring nuclear energy closer to the needs of sustainability, to increase proliferation resistance, and to support concepts able to produce energy (both electricity and process heat) at competitive costs. The U.S. Department of Energy has supported this effort by pursuing the development of the Next Generation Nuclear Plant, a high temperature gas-cooled reactor. This support has included research and development of pertinent data, initial regulatory discussions, and engineering support of various codes and standards development. This report discusses the various applicable American Society of Mechanical Engineers (ASME) codes and standards that are being developed to support these high temperature gascooled reactors during construction and operation. ASME is aggressively pursuing these codes and standards to support an international effort to build the next generation of advanced reactors so that all can benefit.

  4. 77 FR 3073 - American Society of Mechanical Engineers (ASME) Codes and New and Revised ASME Code Cases...

    Science.gov (United States)

    2012-01-23

    ...-AI35 American Society of Mechanical Engineers (ASME) Codes and New and Revised ASME Code Cases... addenda to the ASME Boiler and Pressure Vessel (B&PV) Code, and the ASME Code for Operation and... on their use) ASME B&PV Code Cases N-722-1 and N-770-1. This document is necessary to correct...

  5. International Accreditation of ASME Codes and Standards

    International Nuclear Information System (INIS)

    Green, Mervin R.

    1989-01-01

    ASME established a Boiler Code Committee to develop rules for the design, fabrication and inspection of boilers. This year we recognize 75 years of that Code and will publish a history of that 75 years. The first Code and subsequent editions provided for a Code Symbol Stamp or mark which could be affixed by a manufacturer to a newly constructed product to certify that the manufacturer had designed, fabricated and had inspected it in accordance with Code requirements. The purpose of the ASME Mark is to identify those boilers that meet ASME Boiler and Pressure Vessel Code requirements. Through thousands of updates over the years, the Code has been revised to reflect technological advances and changing safety needs. Its scope has been broadened from boilers to include pressure vessels, nuclear components and systems. Proposed revisions to the Code are published for public review and comment four times per year and revisions and interpretations are published annually; it's a living and constantly evolving Code. You and your organizations are a vital part of the feedback system that keeps the Code alive. Because of this dynamic Code, we no longer have columns in newspapers listing boiler explosions. Nevertheless, it has been argued recently that ASME should go further in internationalizing its Code. Specifically, representatives of several countries, have suggested that ASME delegate to them responsibility for Code implementation within their national boundaries. The question is, thus, posed: Has the time come to franchise responsibility for administration of ASME's Code accreditation programs to foreign entities or, perhaps, 'institutes.' And if so, how should this be accomplished?

  6. Globalization of ASME Nuclear Codes and Standards

    International Nuclear Information System (INIS)

    Swayne, Rick; Erler, Bryan A.

    2006-01-01

    With the globalization of the nuclear industry, it is clear that the reactor suppliers are based in many countries around the world (such as United States, France, Japan, Canada, South Korea, South Africa) and they will be marketing their reactors to many countries around the world (such as US, China, South Korea, France, Canada, Finland, Taiwan). They will also be fabricating their components in many different countries around the world. With this situation, it is clear that the requirements of ASME Nuclear Codes and Standards need to be adjusted to accommodate the regulations, fabricating processes, and technology of various countries around the world. It is also very important for the American Society of Mechanical Engineers (ASME) to be able to assure that products meeting the applicable ASME Code requirements will provide the same level of safety and quality assurance as those products currently fabricated under the ASME accreditation process. To do this, many countries are in the process of establishing or changing their regulations, and it is important for ASME to interface with the appropriate organizations in those countries, in order to ensure there is effective use of ASME Codes and standards around the world. (authors)

  7. 78 FR 37848 - ASME Code Cases Not Approved for Use

    Science.gov (United States)

    2013-06-24

    ... COMMISSION ASME Code Cases Not Approved for Use AGENCY: Nuclear Regulatory Commission. ACTION: Draft... public comment draft regulatory guide (DG), DG-1233, ``ASME Code Cases not Approved for Use.'' This regulatory guide lists the American Society of Mechanical Engineers (ASME) Code Cases that the NRC has...

  8. FY16 ASME High Temperature Code Activities

    Energy Technology Data Exchange (ETDEWEB)

    Swindeman, M. J. [Chromtech Inc., Oak Ridge, TN (United States); Jetter, R. I. [R. I Jetter Consulting, Pebble Beach, CA (United States); Sham, T. -L. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-09-01

    One of the objectives of the ASME high temperature Code activities is to develop and validate both improvements and the basic features of Section III, Division 5, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to be used to assess whether or not a specific component under specified loading conditions will satisfy the elevated temperature design requirements for Class A components in Section III, Division 5, Subsection HB, Subpart B (HBB). There are many features and alternative paths of varying complexity in HBB. The initial focus of this task is a basic path through the various options for a single reference material, 316H stainless steel. However, the program will be structured for eventual incorporation all the features and permitted materials of HBB. Since this task has recently been initiated, this report focuses on the description of the initial path forward and an overall description of the approach to computer program development.

  9. ASME nuclear codes and standards risk management strategic planning

    International Nuclear Information System (INIS)

    Hill, Ralph S. III; Balkey, Kenneth R.; Erler, Bryan A.; Wesley Rowley, C.

    2007-01-01

    This paper is prepared in honor and in memory of the late Professor Emeritus Yasuhide Asada to recognize his contributions to ASME Nuclear Codes and Standards initiatives, particularly those related to risk-informed technology and System Based Code developments. For nearly two decades, numerous risk-informed initiatives have been completed or are under development within the ASME Nuclear Codes and Standards organization. In order to properly manage the numerous initiatives currently underway or planned for the future, the ASME Board on Nuclear Codes and Standards (BNCS) has an established Risk Management Strategic Plan (Plan) that is maintained and updated by the ASME BNCS Risk Management Task Group. This paper presents the latest approved version of the plan beginning with a background of applications completed to date, including the recent probabilistic risk assessment (PRA) standards developments for nuclear power plant applications. The paper discusses planned applications within ASME Nuclear Codes and Standards that will require expansion of the ASME PRA Standard to support new advanced light water reactor and next generation reactor developments, such as for high temperature gas-cooled reactors. Emerging regulatory developments related to risk-informed, performance- based approaches are summarized. A long-term vision for the potential development and evolution to a nuclear systems code that adopts a risk-informed approach across a facility life-cycle (design, construction, operation, maintenance, and closure) is also summarized. Finally, near term and long term actions are defined across the ASME Nuclear Codes and Standards organizations related to risk management, including related U.S. regulatory activities. (author)

  10. Inservice inspection procedures and training according to the ASME code

    International Nuclear Information System (INIS)

    Greenwald, S.M.; Chockie, L.J.

    1987-01-01

    Mandatory training of the technical staff at a nuclear power plant is of paramount importance if we are to avoid costly plant shutdowns. This training should include the requirements for both Preservice and Inservice Inspection, in addition to Quality Assurance procedures as required by the American Society of Mechanical Engineers (ASME) Code. The training is best accomplished by utilizing instructors who are thoroughly familiar with plant operations and the ASME Code, as well as serving on one of the Code committees. This paper focuses on the Inservice Inspection procedures and the results of an intensive training effort to implement such procedures. (author)

  11. Inservice inspection procedures and training according to the ASME code

    Energy Technology Data Exchange (ETDEWEB)

    Greenwald, S.M.; Chockie, L.J.

    1988-01-01

    Mandatory training of the technical staff at a nuclear power plant is of paramount importance if we are to avoid costly plant shutdowns. This training should include the requirements for both Preservice and inservice Inspection, in addition to Quality Assurance procedures as required by the American Society of Mechanical Engineers (ASME) Code. The training is best accomplished by utilizing instructors who are thoroughly familiar with plant operations and the ASME Code, as well as serving on one of the code committees. This paper focuses on the Inservice Inspection procedures and the results of an intensive training effort to implement such procedures.

  12. 46 CFR 57.02-2 - Adoption of section IX of the ASME Code.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section IX of the ASME Code. 57.02-2 Section... AND BRAZING General Requirements § 57.02-2 Adoption of section IX of the ASME Code. (a) The... accordance with section IX of the ASME (American Society of Mechanical Engineers) Code, as limited, modified...

  13. Design Procedure of Graphite Components by ASME HTR Codes

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Ji-Ho; Jo, Chang Keun [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    In this study, the ASME B and PV Code, Subsection HH, Subpart A, design procedure for graphite components of HTRs was reviewed and the differences from metal materials were remarked. The Korean VHTR has a prismatic core which is made of multiple graphite blocks, reflectors, and core supports. One of the design issues is the assessment of the structural integrity of the graphite components because the graphite is brittle and shows quite different behaviors from metals in high temperature environment. The American Society of Mechanical Engineers (ASME) issued the latest edition of the code for the high temperature reactors (HTR) in 2015. In this study, the ASME B and PV Code, Subsection HH, Subpart A, Graphite Materials was reviewed and the special features were remarked. Due the brittleness of graphites, the damage-tolerant design procedures different from the conventional metals were adopted based on semi-probabilistic approaches. The unique additional classification, SRC, is allotted to the graphite components and the full 3-D FEM or equivalent stress analysis method is required. In specific conditions, the oxidation and viscoelasticity analysis of material are required. The fatigue damage rule has not been established yet.

  14. 76 FR 11191 - Hazardous Materials: Adoption of ASME Code Section XII and the National Board Inspection Code

    Science.gov (United States)

    2011-03-01

    ... Hazardous Materials: Adoption of ASME Code Section XII and the National Board Inspection Code AGENCY... the electronic availability of the American Society of Mechanical Engineers' (ASME) Boiler and... the ANPRM published on December 23, 2010 (ANPRM; 75 FR 80765). The ASME Boiler and Pressure Vessel...

  15. Nuclear component design ontology building based on ASME codes

    International Nuclear Information System (INIS)

    Bao Shiyi; Zhou Yu; He Shuyan

    2005-01-01

    The adoption of ontology analysis in the study of concept knowledge acquisition and representation for the nuclear component design process based on computer-supported cooperative work (CSCW) makes it possible to share and reuse numerous concept knowledge of multi-disciplinary domains. A practical ontology building method is accordingly proposed based on Protege knowledge model in combination with both top-down and bottom-up approaches together with Formal Concept Analysis (FCA). FCA exhibits its advantages in the way it helps establish and improve taxonomic hierarchy of concepts and resolve concept conflict occurred in modeling multi-disciplinary domains. With Protege-3.0 as the ontology building tool, a nuclear component design ontology based ASME codes is developed by utilizing the ontology building method. The ontology serves as the basis to realize concept knowledge sharing and reusing of nuclear component design. (authors)

  16. ASME Section XI trends in developing nuclear codes and standards

    International Nuclear Information System (INIS)

    Hedden, O.F.

    1995-01-01

    When the author began working on nuclear power many years ago, he knew that perfection was the only acceptable technical standard. Unfortunately, this became an obsession with perfection that has had unfavorable consequences in some of the non-technical areas of work in ASME nuclear power Codes and Standards. However, the economic problems of the nuclear power industry now demand a more pragmatic approach if the industry is to continue. Not only does each item considered for action need to be evaluated to criteria that may in some cases be less than perfection, but one needs to consider whether it contributes tangibly to either safety or to reduction in technical or administrative burden. These should be the governing, criteria. The introduction of risk-based inspection methodologies will certainly be an important element in doing this successfully. One needs to consider these criteria collectively, as one discusses each item at the committee level, and individually, as one votes on each item. In the past, the author has been concerned that the industry was not acting quickly enough in taking advantage of opportunities offered by the Code to increase safety or to reduce cost. While he still has some concern, he thinks communication channels have been greatly improved. Now he is becoming more concerned with both the collective and individual actions that delay beneficial changes. The second part of the author's talk has to do with the relevance of the code committees in the nuclear power industry regulatory process

  17. ASME Code requirements for multi-canister overpack design and fabrication

    International Nuclear Information System (INIS)

    SMITH, K.E.

    1998-01-01

    The baseline requirements for the design and fabrication of the MCO include the application of the technical requirements of the ASME Code, Section III, Subsection NB for containment and Section III, Subsection NG for criticality control. ASME Code administrative requirements, which have not historically been applied at the Hanford site and which have not been required by the US Nuclear Regulatory Commission (NRC) for licensed spent fuel casks/canisters, were not invoked for the MCO. As a result of recommendations made from an ASME Code consultant in response to DNFSB staff concerns regarding ASME Code application, the SNF Project will be making the following modifications: issue an ASME Code Design Specification and Design Report, certified by a Registered Professional Engineer; Require the MCO fabricator to hold ASME Section III or Section VIII, Division 2 accreditation; and Use ASME Authorized Inspectors for MCO fabrication. Incorporation of these modifications will ensure that the MCO is designed and fabricated in accordance with the ASME Code. Code Stamping has not been a requirement at the Hanford site, nor for NRC licensed spent fuel casks/canisters, but will be considered if determined to be economically justified

  18. Passport of global nuclear business. ASME code certificate acquirement and inspection practices

    International Nuclear Information System (INIS)

    Kawabata, Hiroyuki; Terajima, Makoto; Anami, Kazuhiro

    2010-01-01

    There are possibilities of Japanese nuclear industries to participate in global business such as new and additional construction of nuclear power plants in US and also Asian and other developing countries in the world. It is requisite to acquire ASME code certificate for global business participation, just as passport. This article consists of five papers on present status of ASME code certificate acquirement and inspection practices of nuclear components vendors in the area of Japanese nuclear business. Activities of JSME Committee on Power Generation Facility Codes to make JSME codes corresponded to ASME nuclear codes and standards for their international deployment are also described. (T. Tanaka)

  19. Computer Program of SIE ASME-NH (Revision 1.0) Code

    Energy Technology Data Exchange (ETDEWEB)

    Koo, Gyeong Hoi; Lee, J. H

    2008-01-15

    In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail.

  20. Computer Program of SIE ASME-NH (Revision 1.0) Code

    International Nuclear Information System (INIS)

    Koo, Gyeong Hoi; Lee, J. H.

    2008-01-01

    In this report, the SIE ASME (Structural Integrity Evaluations by ASME-NH) (Revision 1.0), which has a computerized implementation of ASME Pressure Vessels and Piping Code Section III Subsection NH rules, is developed to apply to the next generation reactor design subjecting to the elevated temperature operations over 500 .deg. C and over 30 years design lifetime, and the user's manual for this program is described in detail

  1. Significant issues and changes for ANSI/ASME OM-1 1981, part 1, ASME OMc code-1994, and ASME OM Code-1995, Appendix I, inservice testing of pressure relief devices in light water reactor power plants

    Energy Technology Data Exchange (ETDEWEB)

    Seniuk, P.J.

    1996-12-01

    This paper identifies significant changes to the ANSI/ASME OM-1 1981, Part 1, and ASME Omc Code-1994 and ASME OM Code-1995, Appendix I, {open_quotes}Inservice Testing of Pressure Relief Devices in Light-Water Reactor Power Plants{close_quotes}. The paper describes changes to different Code editions and presents insights into the direction of the code committee and selected topics to be considered by the ASME O&M Working Group on pressure relief devices. These topics include scope issues, thermal relief valve issues, as-found and as-left set-pressure determinations, exclusions from testing, and cold setpoint bench testing. The purpose of this paper is to describe some significant issues being addressed by the O&M Working Group on Pressure Relief Devices (OM-1). The writer is currently the chair of OM-1 and the statements expressed herein represents his personal opinion.

  2. NRC needs and their implementation-ASME Section IX code

    International Nuclear Information System (INIS)

    Liaw, B.D.

    1985-01-01

    The guiding principle from the onset of government regulation for the peaceful use of nuclear energy has been to prescribe only the minimum requirements that are needed for safety. In the pioneer regulators' collective mind, the technical details could be left to the regulated industry through its agents like NSSS vendors and A/E's and their surrogate organizations like ASME, ANS, AIF, etc. However, it has evolved through the years, due either to the bureaucratic momentum or the vacuum in industry leadership, into a situation where one sees an ever increasing number of detailed ''requirements'' prescribed by the regulators. Within the scope of activities covered by Section XI, there is no exception: e.g., NUREG-067, -0531 -1061; NUREG-0313 Rev. 0, Rev. 1, and now Rev. 2; IE Bulletins 82-03, 83-02; and Generic Letters 84-11, and 84-07, etc. for one issue of pipe crack alone; and there are more to come. There appears a consensus among all concerned parties including regulators that this is not a desirable situation and that something must be done to reverse this trend. The purpose of this discussion is, therefore, to explore the areas where the Section XI Code can be restructured to meet this need, and to seek ideas from the representatives of the regulated industry on the methods of implementation that are effective, efficient, and acceptable to all concerned parties

  3. Analysis of preservice inspection relief requests and recommendations for ASME code changes

    International Nuclear Information System (INIS)

    Cook, J.F.

    1985-05-01

    NRC regulations require that preservice inspection (PSI) of nuclear plants be performed in accordance with referenced editions and addenda of Division 1 rules of Section XI, ''Rules for Inservice Inspection of Nuclear Power Plant Components'', of the ASME Boiler and Pressure Vessel Code (ASME Code). The regulations permit applicants to request and obtain relief from the NRC from specific ASME Code requirements that are determined to be impractical. Applicant requests for relief from preservice inspection (PSI) requirements were compiled and analyzed. From this data, covering a total of 178 relief requests, common problems with examination requirements were identified. Changes to examination requirements to solve selected problems are proposed. By following later ASME Code requirements, 46 out of the 178 relief requests can be eliminated. Implementing proposed Code changes would eliminate another 25 relief requests, leaving 107 relief requests out of the original 178 relief requests covered by this survey

  4. Code cases for implementing risk-based inservice testing in the ASME OM code

    Energy Technology Data Exchange (ETDEWEB)

    Rowley, C.W.

    1996-12-01

    Historically inservice testing has been reasonably effective, but quite costly. Recent applications of plant PRAs to the scope of the IST program have demonstrated that of the 30 pumps and 500 valves in the typical plant IST program, less than half of the pumps and ten percent of the valves are risk significant. The way the ASME plans to tackle this overly-conservative scope for IST components is to use the PRA and plant expert panels to create a two tier IST component categorization scheme. The PRA provides the quantitative risk information and the plant expert panel blends the quantitative and deterministic information to place the IST component into one of two categories: More Safety Significant Component (MSSC) or Less Safety Significant Component (LSSC). With all the pumps and valves in the IST program placed in MSSC or LSSC categories, two different testing strategies will be applied. The testing strategies will be unique for the type of component, such as centrifugal pump, positive displacement pump, MOV, AOV, SOV, SRV, PORV, HOV, CV, and MV. A series of OM Code Cases are being developed to capture this process for a plant to use. One Code Case will be for Component Importance Ranking. The remaining Code Cases will develop the MSSC and LSSC testing strategy for type of component. These Code Cases are planned for publication in early 1997. Later, after some industry application of the Code Cases, the alternative Code Case requirements will gravitate to the ASME OM Code as appendices.

  5. Estimates of margins in ASME Code strength values for stainless steel nuclear piping

    International Nuclear Information System (INIS)

    Ware, A.G.

    1995-01-01

    The margins in the ASME Code stainless steel allowable stress values that can be attributed to the variations in material strength are evaluated for nuclear piping steels. Best-fit curves were calculated for the material test data that were used to determine allowable stress values for stainless steels in the ASME Code, supplemented by more recent data, to estimate the mean stresses. The mean yield stresses from the test data are about 15 to 20% greater than the ASME Code yield stress values (the stainless steel S m values are based on the yield stress). The ASME Code yield stress values are estimated to approximately coincide with the 97% confidence limit from the test data. The mean and 97% confidence limit values can be used in probabilistic risk assessments of nuclear piping

  6. ASME code considerations for the compact heat exchanger

    Energy Technology Data Exchange (ETDEWEB)

    Nestell, James [MPR Associates Inc., Alexandria, VA (United States); Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-08-31

    robustness. Classic shell and tube designs will be large and costly, and may only be appropriate in steam generator service in the SHX where boiling inside the tubes occurs. For other energy conversion systems, all of these features can be met in a compact heat exchanger design. This report will examine some of the ASME Code issues that will need to be addressed to allow use of a Code-qualified compact heat exchanger in IHX or SHX nuclear service. Most effort will focus on the IHX, since the safety-related (Class A) design rules are more extensive than those for important-to-safety (Class B) or commercial rules that are relevant to the SHX.

  7. ASME nuclear codes and standards: Scope of coverage and current initiatives

    International Nuclear Information System (INIS)

    Eisenberg, G. M.

    1995-01-01

    The objective of this paper is to address the broad scope of coverage of nuclear codes, standards and guides produced and administered by the American Society of Mechanical Engineers (ASME). Background information is provided regarding the evolution of the present activities. Details are provided on current initiatives intended to permit ASME to meet the needs of a changing nuclear industry on a worldwide scale. During the early years of commercial nuclear power, ASME produced a code for the construction of nuclear vessels used in the reactor coolant pressure boundary, containment and auxiliary systems. In response to industry growth, ASME Code coverage soon broadened to include rules for construction of other nuclear components, and inservice inspection of nuclear reactor coolant systems. In the years following this, the scope of ASME nuclear codes, standards and guides has been broadened significantly to include air cleaning activities for nuclear power reactors, operation and maintenance of nuclear power plants, quality assurance programs, cranes for nuclear facilities, qualification of mechanical equipment, and concrete reactor vessels and containments. ASME focuses on globalization of its codes, standards and guides by encouraging and promoting their use in the international community and by actively seeking participation of international members on its technical and supervisory committees and in accreditation activities. Details are provided on current international representation. Initiatives are underway to separate the technical requirements from administrative and enforcement requirements, to convert to hard metric units, to provide for non-U. S. materials, and to provide for translations into non-English languages. ASME activity as an accredited ISO 9000 registrar for suppliers of mechanical equipment is described. Rules are being developed for construction of containment systems for nuclear spent fuel and high-level waste transport packagings. Intensive

  8. Impact of ACI-ASME code on design and construction of nuclear containment structures

    International Nuclear Information System (INIS)

    Reedy, R.F.

    1978-01-01

    The effect of the ACI-ASME code for design and construction of concrete containment structures on the nuclear and concrete industries is examined. Topics covered include purpose of the code, general requirements, responsibilities and duties, design and construction specifications, quality assurance, inspection, the liner, and stamping

  9. Basic requirements of mechanical properties for nuclear pressure vessel materials in ASME-BPV code

    International Nuclear Information System (INIS)

    Ning Dong; Yao Weida

    2011-01-01

    The four basic aspects of strengths, ductility, toughness and fatigue strengths can be summarized for overall mechanical properties requirements of materials for nuclear pressure-retaining vessels in ASME-BPV code. These mechanical property indexes involve in the factors of melting, manufacture, delivery conditions, check or recheck for mechanical properties and chemical compositions, etc. and relate to degradation and damage accumulation during the use of materials. This paper specifically accounts for the basic requirements and theoretic basis of mechanical properties for nuclear pressure vessel materials in ASME-BPV code and states the internal mutual relationships among the four aspects of mechanical properties. This paper focuses on putting forward at several problems on mechanical properties of materials that shall be concerned about during design and manufacture for nuclear pressure vessels according to ASME-BPV code. (author)

  10. 46 CFR 52.01-2 - Adoption of section I of the ASME Boiler and Pressure Vessel Code.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section I of the ASME Boiler and Pressure... and Pressure Vessel Code. (a) Main power boilers and auxiliary boilers shall be designed, constructed, inspected, tested, and stamped in accordance with section I of the ASME Boiler and Pressure Vessel Code...

  11. 46 CFR 53.01-3 - Adoption of section IV of the ASME Boiler and Pressure Vessel Code.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of section IV of the ASME Boiler and Pressure... Boiler and Pressure Vessel Code. (a) Heating boilers shall be designed, constructed, inspected, tested, and stamped in accordance with section IV of the ASME Boiler and Pressure Vessel Code (incorporated by...

  12. Researching on knowledge architecture of design by analysis based on ASME code

    International Nuclear Information System (INIS)

    Bao Shiyi; Zhou Yu; He Shuyan

    2003-01-01

    The quality of knowledge-based system's knowledge architecture is one of decisive factors of knowledge-based system's validity and rationality. For designing the ASME code knowledge based system, this paper presents a knowledge acquisition method which is extracting knowledge through document analysis consulted domain experts' knowledge. Then the paper describes knowledge architecture of design by analysis based on the related rules in ASME code. The knowledge of the knowledge architecture is divided into two categories: one is empirical knowledge, and another is ASME code knowledge. Applied as the basement of the knowledge architecture, a general procedural process of design by analysis that is met the engineering design requirements and designers' conventional mode is generalized and explained detailed in the paper. For the sake of improving inference efficiency and concurrent computation of KBS, a kind of knowledge Petri net (KPN) model is proposed and adopted in expressing the knowledge architecture. Furthermore, for validating and verifying of the empirical rules, five knowledge validation and verification theorems are given in the paper. Moreover the research production is applicable to design the knowledge architecture of ASME codes or other engineering standards. (author)

  13. Technical justification for ASME code section xi crack detection by visual examination

    International Nuclear Information System (INIS)

    Nickell, R.E.; Rashid, Y.R.

    2001-01-01

    A critical technical element of nuclear power plant license renewal in the United States is the demonstration that the effects of aging do not compromise the intended safety function(s) of a system, structure, or component during the extended term of operation. The demonstration may take either of two forms. First, it can be shown that the design basis for the system, structure, or component is sufficiently robust that the aging effects have been insignificant through the current license term, and will continue to be insignificant through the extended term. Alternatively, it can be shown that, while the aging effects may be potentially significant, those effects can be managed and functionality maintained by defined programmatic activities during the extended term of operation. The first of the two approaches is generally provided by the construction basis, such as construction in accordance with the ASME Code Section III and other consensus codes and standards. The second of the two approaches is often provided by periodic inservice inspection and testing, in accordance with the ASME Code Section XI. The purpose of the ASME Section XI inspections and tests is to assure that systems, components, and structures are fit for continued service until the next scheduled inspection or test. The purpose of this paper is to document the effectiveness of the current ASME Code Section XI visual examination procedures in detecting the effects of aging for systems, structures, and components that are tolerant of mature cracks. (author)

  14. Appropriate nominal stresses for use with ASME Code pressure-loading stress indices for nozzles

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.

    1976-06-01

    This program is part of a cooperative effort with industry to develop and verify analytical methods for assessing the safety of nuclear pressure-vessel and piping-system design. The study of nominal stresses and stress indices described is part of a continuing study of design rules for nozzles in pressure vessels being coordinated by the PVRC Subcommittee on Reinforced Openings and External Loadings. Results from these studies are used by appropriate ASME Code groups in drafting new and improved design rules

  15. Modification of the ASME code z-factor for circumferential surface crack in nuclear ferritic pipings

    International Nuclear Information System (INIS)

    Choi, Young Hwan; Chung, Yon Ki; Koh, Wan Young; Lee, Joung Bae

    1996-01-01

    The purpose of this paper is to modify the ASME Code Z-Factor, which is used in the evaluation of circumferential surface crack in nuclear ferritic pipings. The ASME Code Z-Factor is a load multiplier to compensate plastic load with elasto-plastic load. The current ASME Code Z-Factor underestimates pipe maximum load. In this study, the original SC. TNP method is modified first because the original SC. TNP method has a problem that the maximum allowable load predicted from the original SC. TNP method is slightly higher than that measured from the experiment. Then the new Z-Factor is developed using the modified SC. TNP method. The desirability of both the modified SC. TNP method and the new Z-Factor is examined using the experimental results for the circumferential surface crack in pipings. The results show that (1) the modified SC. TNP method is good for predicting the circumferential surface crack behavior in pipings, and (2) the Z-Factor obtained from the modified SC. TNP method well predicts the behavior of circumferential surface crack in ferritic pipings. 30 refs., 13 figs., 4 tabs. (author)

  16. Materials and design bases issues in ASME Code Case N-47

    International Nuclear Information System (INIS)

    Huddleston, R.L.; Swindeman, R.W.

    1993-04-01

    A preliminary evaluation of the design bases (principally ASME Code Case N-47) was conducted for design and operation of reactors at elevated temperatures where the time-dependent effects of creep, creep-fatigue, and creep ratcheting are significant. Areas where Code rules or regulatory guides may be lacking or inadequate to ensure the operation over the expected life cycles for the next-generation advanced high-temperature reactor systems, with designs to be certified by the US Nuclear Regulatory Commission, have been identified as unresolved issues. Twenty-two unresolved issues were identified and brief scoping plans developed for resolving these issues

  17. Application of ASME code AG-1 to YGN 3 ampersand 4 plants, South Korea

    International Nuclear Information System (INIS)

    Kim, Y.K.; Porco, R.D.; York, Y.D.

    1993-01-01

    Yonggwang Nuclear Power Plant Units 3 ampersand 4 are located on the southwestern coast of South Korea on the Yellow Sea. The plant is owned by Korea Electric Power Corp. (KEPCO), with the engineering being performed by Korea Power Engineering Co., Inc. (KOPEC) and Sargent and Lundy under a technology transfer agreement. The plants are both 950 Megawatt (electric) pressurized water reactors of US design. Under contract to KEPCO, Korea Heavy Industries and Construction Co., Ltd. and Ellis and Watts, Division of Dynamics Corporation of America, Batavia, Ohio, supplied major components to the YGN plants in compliance to ASME AG-1. These components included safety related Air Cleaning Units, Reactor containment Fan Cooler Units, Air Handling Units, Cubicle Coolers, Duct Electric Heaters, and fans. This paper details the extent of applicability of ASME Code AG-1 to the specific equipment, description of the equipment, conformance, testing, and design required. The paper also discusses the problems encountered in implementing ASME AG-1, working around Code sections that were not complete at contract inception, conflicts in project documents and related problems. Also discussed are the logistics problems, material availability, and quality assurance aspects complicating the applications of ASME AG-1, due to the required Korean content for some components. Based on successfully supplying the equipment referenced above, it has been concluded that AG-1 is a working document and can be successfully implemented. It provides the requirements necessary for performance, design, construction, acceptance testing, and quality assurance of equipment used as components in nuclear air and gas treatment systems in nuclear facilities. The paper also addresses lessons learned and aspects of mixing US design and US built components in Korean built assemblies

  18. Application of the ASME code in designing containment vessels for packages used to transport radioactive materials

    International Nuclear Information System (INIS)

    Raske, D.T.; Wang, Z.

    1992-01-01

    The primary concern governing the design of shipping packages containing radioactive materials is public safety during transport. When these shipments are within the regulatory jurisdiction of the US Department of Energy, the recommended design criterion for the primary containment vessel is either Section III or Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code, depending on the activity of the contents. The objective of this paper is to discuss the design of a prototypic containment vessel representative of a packaging for the transport of high-level radioactive material

  19. Nupack, the new ASME code for radioactive material transportation packaging containments

    International Nuclear Information System (INIS)

    Turula, P.

    1998-01-01

    The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as Nupack, has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used for the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper

  20. Draft ASME code case on ductile cast iron for transport packaging

    Energy Technology Data Exchange (ETDEWEB)

    Saegusa, T. [Central Research Inst. of Electric Power Industry, Abiko (Japan); Arai, T. [Central Research Inst. of Electric Power Industry, Yokosuka (Japan); Hirose, M. [Nuclear Fuel Transport Co., Ltd., Tokyo (Japan); Kobayashi, T. [Nippon Chuzo, Kawasaki (Japan); Tezuka, Y. [Mitsubishi Materials Co., Tokyo (Japan); Urabe, N. [Kokan Keisoku K. K., Kawasaki (Japan); Hueggenberg, R. [GNB, Essen (Germany)

    2004-07-01

    The current Rules for Construction of ''Containment Systems for Storage and Transport Packagings of Spent Nuclear Fuel and High Level Radioactive Material and Waste'' of Division 3 in Section III of ASME Code (2001 Edition) does not include ductile cast iron in its list of materials permitted for use. The Rules specify required fracture toughness values of ferritic steel material for nominal wall thickness 5/8 to 12 inches (16 to 305 mm). New rule for ductile cast iron for transport packaging of which wall thickness is greater than 12 inches (305mm) is required.

  1. Technical Review on Fitness-for-Service for Buried Pipe by ASME Code Case N-806

    International Nuclear Information System (INIS)

    Park, Sang Kyu; Lee, Yo Seop; So, Il Su; Lim, Bu Taek

    2012-01-01

    Fitness-for-Service is a useful technology to determine replacement timing, next inspection timing or in-service when nuclear power plant's buried pipes are damaged. If is possible for buried pipes to be aged by material loss, cracks and occlusion as operating time goes by. Therefore Fitness-for-Service technology for buried pipe is useful for plant industry to perform replacement and repair. Fitness-for-Service for buried pipe is studied in terms of existing code and standard for Fitness-for-Service and a current developing code case. Fitness-for-Service for buried pipe was performed according to Code Case N-806 developed by ASME (American Society of Mechanical Engineers)

  2. Comparison of ASME Code NB-3200 and NB-3600 results for fatigue analysis of B31.1 branch nozzles

    International Nuclear Information System (INIS)

    Nitzel, M.E.; Ware, A.G.; Morton, D.K.

    1996-01-01

    Fatigue analyses wre conducted on two reactor coolant system branch nozzles in an operating PWR designed to the B31.1 Code, for which no explicit fatigue analysis was required by the licensing basis. These analyses were performed as part of resolving issues connected with NRC's Fatigue Action Plan to determine if the cumulative usage factor (CUF) for these nozzles, using the 1992 ASME Code and representative PWR transients, were comparable to nozzles designed and analyzed to the ASME Code. Both NB-3200 and NB-3600 ASME Code methods were used. NB-3200 analyses included the development of finite element models for each nozzle. Although detailed thermal transients were not available for the plant analyzed, representative transients from similar PWRs were applied in each method. CUFs calculated using NB-3200 methods were significantly less than using NB-3600. The paper points out differences in analysis methods and highlights difficulties and unknowns in performing more detailed analyses to reduce conservative assumptions

  3. Description of comprehensive pump test change to ASME OM code, subsection ISTB

    International Nuclear Information System (INIS)

    Hartley, R.S.

    1994-01-01

    The American Society of Mechanical Engineers (ASME) Operations and Maintenance (OM) Main Committee and Board on Nuclear Codes and Standards (BNCS) recently approved changes to ASME OM Code-1990, Subsection ISTB, Inservice Testing of Pumps in Light-Water Reactor Power Plants. The changes will be included in the 1994 addenda to ISTB. The changes, designated as the comprehensive pump test, incorporate a new, improved philosophy for testing safety-related pumps in nuclear power plants. An important philosophical difference between the open-quotes old codeclose quotes inservice testing (IST) requirements and these changes is that the changes concentrate on less frequent, more meaningful testing while minimizing damaging and uninformative low-flow testing. The comprehensive pump test change establishes a more involved biannual test for all pumps and significantly reduces the rigor of the quarterly test for standby pumps. The increased rigor and cost of the biannual comprehensive tests are offset by the reduced cost of testing and potential damage to the standby pumps, which comprise a large portion of the safety-related pumps at most plants. This paper provides background on the pump testing requirements, discusses potential industry benefits of the change, describes the development of the comprehensive pump test, and gives examples and reasons for many of the specific changes. This paper also describes additional changes to ISTB that will be included in the 1994 addenda that are associated with, but not part of, the comprehensive pump test

  4. Evaluation of conservatisms and environmental effects in ASME Code, Section III, Class 1 fatigue analysis

    International Nuclear Information System (INIS)

    Deardorff, A.F.; Smith, J.K.

    1994-08-01

    This report documents the results of a study regarding the conservatisms in ASME Code Section 3, Class 1 component fatigue evaluations and the effects of Light Water Reactor (LWR) water environments on fatigue margins. After review of numerous Class 1 stress reports, it is apparent that there is a substantial amount of conservatism present in many existing component fatigue evaluations. With little effort, existing evaluations could be modified to reduce the overall predicted fatigue usage. Areas of conservatism include design transients considerably more severe than those experienced during service, conservative grouping of transients, conservatisms that have been removed in later editions of Section 3, bounding heat transfer and stress analysis, and use of the ''elastic-plastic penalty factor'' (K 3 ). Environmental effects were evaluated for two typical components that experience severe transient thermal cycling during service, based on both design transients and actual plant data. For all reasonable values of actual operating parameters, environmental effects reduced predicted margins, but fatigue usage was still bounded by the ASME Section 3 fatigue design curves. It was concluded that the potential increase in predicted fatigue usage due to environmental effects should be more than offset by decreases in predicted fatigue usage if re-analysis were conducted to reduce the conservatisms that are present in existing component fatigue evaluations

  5. Nupack, the new Asme code for radioactive material transportation packaging containments

    International Nuclear Information System (INIS)

    Turula, P.

    1998-01-01

    The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as 'Nupack', has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper. Participation in the Nupack development work described in this paper was supported by the U.S. Department of Energy. (authors)

  6. Section XI of the ASME code: A new approach to qualifying procedures and personnel

    International Nuclear Information System (INIS)

    Chokie, L.J.

    1985-01-01

    Following the results of numerous programs and trials which measured the effectiveness of the nondestructive examinations required by Section XI of the ASME Code on Nuclear Inservice Inspection of Nuclear Power Plant Components, revisions have been made to the Code to improve the over-all reliability. The results of the round-robin programs designed to measure the reliability of detection and the reliability of correctly sizing the flaws indicated that the rather specific requirements in Section XI did not always achieve the desired results in both heavy section pressure vessel steels, nor in austenitic stainless steel piping welds. One of the two major contributors to the less-than-desired reliability was identified as being the training, understanding and qualification of the personnel; the other was principally due to the fact that the exact methods specified in the Code were not always applicable on every steel or every weld joint configuration. Revisions to the Code were proposed and approved to address these deficiencies, and which revisions have been issued for immediate implementation. The new approach is to permit any procedure or method to be used provided the procedure can be qualified on actual specimens containing the type of flaws to be detected, and following the qualification of the procedure, the personnel must be trained and qualified to obtain a certain level of proficiency using the qualified procedure on actual samples. The qualification of each procedure and each individual is required before examining an actual nuclear plant

  7. Comparative evaluation of structural integrity for ITER blanket shield block based on SDC-IC and ASME code

    Energy Technology Data Exchange (ETDEWEB)

    Shim, Hee-Jin [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Ha, Min-Su, E-mail: msha12@nfri.re.kr [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Sa-Woong; Jung, Hun-Chea [ITER Korea, National Fusion Research Institute, 169-148 Gwahak-Ro, Yuseong-Gu, Daejeon (Korea, Republic of); Kim, Duck-Hoi [ITER Organization, Route de Vinon sur Verdon - CS 90046, 13067 Sant Paul Lez Durance (France)

    2016-11-01

    Highlights: • The procedure of structural integrity and fatigue assessment was described. • Case studies were performed according to both SDC-IC and ASME Sec. • III codes The conservatism of the ASME code was demonstrated. • The study only covers the specifically comparable case about fatigue usage factor. - Abstract: The ITER blanket Shield Block is a bulk structure to absorb radiation and to provide thermal shielding to vacuum vessel and external vessel components, therefore the most significant load for Shield Block is the thermal load. In the previous study, the thermo-mechanical analysis has been performed under the inductive operation as representative loading condition. And the fatigue evaluations were conducted to assure structural integrity for Shield Block according to Structural Design Criteria for In-vessel Components (SDC-IC) which provided by ITER Organization (IO) based on the code of RCC-MR. Generally, ASME code (especially, B&PV Sec. III) is widely applied for design of nuclear components, and is usually well known as more conservative than other specific codes. For the view point of the fatigue assessment, ASME code is very conservative compared with SDC-IC in terms of the reflected K{sub e} factor, design fatigue curve and other factors. Therefore, an accurate fatigue assessment comparison is needed to measure of conservatism. The purpose of this study is to provide the fatigue usage comparison resulting from the specified operating conditions shall be evaluated for Shield Block based on both SDC-IC and ASME code, and to discuss the conservatism of the results.

  8. 46 CFR 54.01-2 - Adoption of division 1 of section VIII of the ASME Boiler and Pressure Vessel Code.

    Science.gov (United States)

    2010-10-01

    ... Boiler and Pressure Vessel Code. 54.01-2 Section 54.01-2 Shipping COAST GUARD, DEPARTMENT OF HOMELAND... division 1 of section VIII of the ASME Boiler and Pressure Vessel Code. (a) Pressure vessels shall be designed, constructed, and inspected in accordance with section VIII of the ASME Boiler and Pressure Vessel...

  9. Elastic-plastic stress analysis and ASME code evaluation of a bottomhead penetration in a reactor pressure vessel

    International Nuclear Information System (INIS)

    Ranganath, S.

    1979-01-01

    Nuclear pressure vessel components are designed to meet the requirements of Section III of the ASME Boiler and Pressure Vessel Code. Specifically, the design must satisfy the limits on stress range and fatigue usage prescribed in NB-3200, Section III ASME Code for the various design and operating conditions for the component. The Code requirements assure that the component does not experience gross yielding and that in general, elastic shakedown occurs following cyclic loading. When elastic stress analysis is performed this can be shown by meeting the limits in the Code on Primary and Primary plus Secondary (P+Q) stress intensities. However, when the P+Q limits cannot be met and elastic Shakedown cannot be demonstrated, plastic analysis may be performed to meet the requirements of the Code. This paper describes the elastic-plastic stress analysis of a Boiling Water Reactor Vessel bottom head in-core penetration and illustrates how plastic analysis can be used in ASME Code evaluations to show Code compliance. Details of the thermal analysis, elastic-plastic stress analysis and fatigue evaluation are presented and it is shown that the in-core penetration satisfies the code requirements. 6 refs

  10. Development of a software for the ASME code qualification of class-I nuclear piping systems

    International Nuclear Information System (INIS)

    Mishra, Rajesh; Umashankar, C.; Soni, R.S.; Kushwaha, H.S.; Venkat Raj, V.

    1999-11-01

    In nuclear industry, the designer often comes across the requirements of Class-1 piping systems which need to be qualified for various normal and abnormal loading conditions. In order to have quick design changes and the design reviews at various stages of design, it is quite helpful if a dedicated software is available for the qualification of Class-1 piping systems. BARC has already purchased a piping analysis software CAESAR-II and has used it for the life extension of heavy water plant, Kota. CAESAR-II facilitates the qualification of Class-2 and Class-3 piping systems among others. However, the present version of CAESAR-II does not have the capability to perform stress checks for the ASME Class-1 nuclear piping systems. With this requirement in mind and the prohibitive costs of commercially available software for the Class-1 piping analyses, it was decided to develop a separate software for this class of piping in such a way that the input and output details of the piping from the CAESAR-II software can be made use of. This report principally contains the details regarding development of a software for codal qualification of Class-1 nuclear piping as per ASME code section-III, NB-3600. The entire work was carried out in three phases. The first phase consisted of development of the routines for reading the output files obtained from the CAESAR-II software, and converting them into required format for further processing. In this phase, the nodewise informations available from the CAESAR-II output file were converted into element-wise informations. The second phase was to develop a general subroutine for reading the various input parameters such as diameter, wall thickness, corrosion allowance, bend radius and also to recognize the bend elements based on the bend radius, directly from the input file of CAESAR-II software. The third phase was regarding the incorporation of the required steps for performing the ASME codal checks as per NB-3600 for Class-1 piping

  11. The application of RCM to ASME code requirements for in-service testing

    International Nuclear Information System (INIS)

    Rowley, C.W.

    1990-01-01

    This paper reports that the high reliability of nuclear power plant systems and components is highly important for both nuclear safety and electrical power production economics. The optimum operating performance of these plant systems and components is heavily dependent on the original or modified design for its inherent reliability and the appropriate trade-off in preventive and corrective maintenance for its developed reliability. In developing this optimum operating performance goal, the plant staff could rely solely on the experience of its personnel. However using this internal subjective approach, the average nuclear power availability has been far less than 80%. Obviously the production economics of a nuclear power plant is the province of the owner-operator, but the safety system and component performance impacts the entire industry. Hence the nuclear industry needs to have in-service testing requirements that maintain the necessary safety standards. Historically the ASME Inservice Testing Code has been a vehicle for defining some of those necessary safety standards, such as inservice testing of pumps, valves, and snubbers. The nuclear industry needs to expand the code testing to include all the systems that affect these necessary safety standards

  12. Comparative study of design of piping supports class 1, 2 and 3 considering german code KTA and ASME III - NF

    International Nuclear Information System (INIS)

    Faloppa, Altair A.; Fainer, Gerson; Mattar Neto, Miguel; Elias, Marcos V.

    2013-01-01

    The objective of this paper is developing a comparative study of the design criteria for class 1, 2, 3 piping supports considering the American Code ASME Section III - NF and the German Code KTA 3205.1 to the Primary Circuit, KTA 3205.2 to the others systems and KTA 3205.3 series-production standards supports of a PWR nuclear power plant. An additional purpose of the paper is a general analysis of the main design concepts of the American Code ASME Boiler and Pressure Vessel Code, Section III, Division 1 and German Nuclear Design Code KTA that was performed in order to aid the comparative study proposed. The relevance of this study is to show the differences between codes ASME and KTA since they were applied in the design of the Nuclear Power Plants Angra 1 and Angra 2, and to the design of Angra 3, which is at the moment under construction. It is also considered their use in the design of nuclear installations such as RMB - Reator MultiProposito Brasileiro and LABGENE - Laboratorio de Geracao Nucleoeletrica. (author)

  13. Development and application of proposed ASME Section XI Code changes for risk-based inspection of piping

    International Nuclear Information System (INIS)

    West, R.A.

    1996-01-01

    This synopsis has been written to describe a perspective on the development and application of ASME Section XI Code changes for risk-based inspection of piping. The content is specifically related to the use of risk-based technology for Inservice Inspection (ISI) of piping and efforts made to support the ASME Research/Westinghouse Owners Group/Millstone Unit 3 approach for use of this technology. The opinions contained herein may or may not reflect those of the ASME Codes and Standards Committees responsible for these activities. In order to take such a detailed technical subject and put it into an understandable format, the author has chosen to provide an analogy to simplify what is actually taking place. Risk-based technology in the ISI of piping can be likened to the process of making and using specifically ground prescription glasses to allow for better vision. It provides a process to develop and use these uniquely ground glasses that will dynamically focus on all the locations and obstacles within a plant's piping systems that could cause that plant to trip and fall; more importantly it identifies the locations where the fall could possibly hurt someone else. In this way, Nuclear Safety is being addressed

  14. Comparisons of ASME-code fatigue-evaluation methods for nuclear Class 1 piping with Class 2 or 3 piping

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.

    1983-06-01

    The fatigue evaluation procedure used in the ASME Boiler and Pressure Vessel Code, Sect. III, Nuclear Power Plant Components, for Class 1 piping is different from the procedure used for Class 2 or 3 piping. The basis for each procedure is described, and correlations between the two procedures are presented. Conditions under which either procedure or both may be unconservative are noted. Potential changes in the Class 2 or 3 piping procedure to explicitly cover all loadings are discussed. However, the report is intended to be informative, and while the contents of the report may guide future Code changes, specific recommendations are not given herein

  15. Evaluation of the integrity of reactor vessels designed to ASME Code, Sections I and/or VIII

    International Nuclear Information System (INIS)

    Hoge, K.G.

    1976-01-01

    A documented review of nuclear reactor pressure vessels designed to ASME Code, Sections I and/or VIII is made. The review is primarily concerned with the design specifications and quality assurance programs utilized for the reactor vessel construction and the status of power plant material surveillance programs, pressure-temperature operating limits, and inservice inspection programs. The following ten reactor vessels for light-water power reactors are covered in the report: Indian Point Unit No. 1, Dresden Unit No. 1, Yankee Rowe, Humboldt Bay Unit No. 3, Big Rock Point, San Onofre Unit No. 1, Connecticut Yankee, Oyster Creek, Nine Mile Point Unit No. 1, and La Crosse

  16. ASME power test code ptc 4.1 for steam generators; Codigo de pruebas de potencia ASME ptc 4.1 para generadores de vapor

    Energy Technology Data Exchange (ETDEWEB)

    Plauchu Alcantara, Jorge Alberto [Plauchu Consultores, Morelia, Michoacan (Mexico)

    2001-07-01

    This presentation is oriented towards those who in this subject have experience in the design and equipment specification, plant projects, factory and field testing, operation or result analyses. An important fraction of the national energy supply, approximately 13%, is applied to the steam generation in the different aspects of the industrial activity, in the electrical industry of public service and in the commercial and services sector. The development of the national programs of energy efficiency verifies this when dedicating to this use of the energy important projects, some of them with support of the USAID. The measurement of the energy utilization or the efficiency of steam generators (or boilers) is made applying some procedure agreed by the parts and the one of greater acceptance and best known in Mexico and internationally is the ASME Power Test Code PTC 4.1 for Steam Generators. The purpose and formality in the determination of efficiency and of steam generation capacity behavior, thermal basic regime or fulfillment of guarantees, radically changes the exigencies of strict attachment to the PTC 4.1 This definition will determine the importance of the test method selected, the deviations and convened exceptions, the influence of the precision and the measurement errors, the consideration of auxiliary equipment, etc. An interpretation or incorrect application of the Test Code has lead and will lead to results and nonreliable decisions. [Spanish] Esta exposicion se orienta a quienes en este tema cuenta con experiencia en diseno y especificacion de equipo, proyecto de planta, pruebas en fabrica y campo, operacion o analisis de resultados. Una fraccion importante de la oferta nacional de energia, 13% aproximadamente, se aplica a la generacion de vapor en diferentes giros de actividad industrial, en la industria electrica, de servicio publico y en el sector de servicios y comercial. El desarrollo de los programas nacionales de eficiencia energetica comprueba

  17. Comparisons of ratchetting analysis methods using RCC-M, RCC-MR and ASME codes

    International Nuclear Information System (INIS)

    Yang Yu; Cabrillat, M.T.

    2005-01-01

    The present paper compares the simplified ratcheting analysis methods used in RCC-M, RCC-MR and ASME with some examples. Firstly, comparisons of the methods in RCC-M and efficiency diagram in RCC-MR are investigated. A special method is used to describe these two methods with curves in one coordinate, and the different conservation is demonstrated. RCC-M method is also be interpreted by SR (second ratio) and v (efficiency index) which is used in RCC-MR. Hence, we can easily compare the previous two methods by defining SR as abscissa and v as ordinate and plotting two curves of them. Secondly, comparisons of the efficiency curve in RCC-MR and methods in ASME-NH APPENDIX T are investigated, with significant creep. At last, two practical evaluations are performed to show the comparisons of aforementioned methods. (authors)

  18. A practical example of code comparison evaluation of conformance to the Asme 3 code of large nuclear replacement parts manufactured according to RCC-M

    International Nuclear Information System (INIS)

    Dunand-Roux, L.; Berger, T.; Grandemange, J.M.; Lemoine, M.

    2004-01-01

    This paper summarizes the work carried out to evaluate the compliance of a French RCC-M practice with the ASME Code, for installation of pressurized water reactor closure heads manufactured as per the French regulations, on American nuclear power plants. This evaluation covers all requirements regarding: - Materials and purchases, - Design and analysis, - Manufacturing, welding and related qualifications, - Non-destructive inspections. On completion of this evaluation, a number of additional justifications were produced, revealing that the technical solutions retained are compatible with both construction codes. (authors)

  19. Code on nuclear air and gas treatment ASME/ANSI AG-1

    International Nuclear Information System (INIS)

    Miller, W.H. Jr.

    1993-01-01

    The focus of this panel is on equipment code section work over the past two years. Major topics include changes in Filter Code Sections, revamping of the Ductwork Code Section, and emergence of an improved I ampersand C Code Section. Actual applications of AG-1 are to be discussed by CONAGT members. Remaining time will be devoted to fielding questions concerning ASMA/ANSI AG-1

  20. Evaluation of the plastic characteristics of piping products in relation to ASME code criteria

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.; Moore, S.E.

    1978-07-01

    Theories and test data relevant to the plastic characteristics of piping products are presented and compared with Code Equations in NB-3652 for Class 1 piping; in NC/ND-3652.2 for Class 2 and Class 3 piping. Comparisons are made for (a) straight pipe, (b) elbows, (c) branch connections, and (d) tees. The status of data (or lack of data) for other piping components is discussed. Comparisons are made between available data and the Code equations for two typical piping materials, SA106 Grade B and SA312 TP304, for Code Design Limits, and Service Limits A, B, C, and D. Conditions under which the Code Limits cannot be shown to be conservative from available data are pointed out. Based on the results of the study, recommendations for Code revisions are presented, along with recommendations for additional work

  1. News from the Library: A new key reference work for the engineer: ASME's Boiler and Pressure Vessel Code at the CERN Library

    CERN Multimedia

    CERN Library

    2011-01-01

    The Library is aiming at offering a range of constantly updated reference books, to cover all areas of CERN activity. A recent addition to our collections strengthens our offer in the Engineering field.   The CERN Library now holds a copy of the complete ASME Boiler and Pressure Vessel Code, 2010 edition. This code establishes rules of safety governing the design, fabrication, and inspection of boilers and pressure vessels, and nuclear power plant components during construction. This document is considered worldwide as a reference for mechanical design and is therefore important for the CERN community. The Code published by ASME (American Society of Mechanical Engineers) is kept current by the Boiler and Pressure Committee, a volunteer group of more than 950 engineers worldwide. The Committee meets regularly to consider requests for interpretations, revision, and to develop new rules. The CERN Library receives updates and includes them in the volumes until the next edition, which is expected to ...

  2. Case study of the propagation of a small flaw under PWR loading conditions and comparison with the ASME code design life. Comparison of ASME Code Sections III and XI

    International Nuclear Information System (INIS)

    Yahr, G.T.; Gwaltney, R.C.; Richardson, A.K.; Server, W.L.

    1986-01-01

    A cooperative study was performed by EG and G Idaho, Inc., and Oak Ridge National Laboratory to investigate the degree of conservatism and consistency in the ASME Boiler and Pressure Vessel Code Section III fatigue evaluation procedure and Section XI flaw acceptance standards. A single, realistic, sample problem was analyzed to determine the significance of certain points of criticism made of an earlier parametric study by staff members of the Division of Engineering Standards of the Nuclear Regulatory Commission. The problem was based on a semielliptical flaw located on the inside surface of the hot-leg piping at the reactor vessel safe-end weld for the Zion 1 pressurized-water reactor (PWR). Two main criteria were used in selecting the problem; first, it should be a straight pipe to minimize the computational expense; second, it should exhibit as high a cumulative usage factor as possible. Although the problem selected has one of the highest cumulative usage factors of any straight pipe in the primary system of PWRs, it is still very low. The Code Section III fatigue usage factor was only 0.00046, assuming it was in the as-welded condition, and fatigue crack-growth analyses predicted negligible crack growth during the 40-year design life. When the analyses were extended past the design life, the usage factor was less than 1.0 when the flaw had propagated to failure. The current study shows that the criticism of the earlier report should not detract from the conclusion that if a component experiences a high level of cyclic stress corresponding to a fatigue usage factor near 1.0, very small cracks can propagate to unacceptable sizes

  3. CEASEMT system: the TEDEL code. Pipings - Plasticity - Dynamics - Statics - Buckling - Thermoplasticity - Creep - Large displacements - FLUIDS - SEISMS - ASME

    International Nuclear Information System (INIS)

    Hoffmann, Alain; Jeanpierre, Francoise; Axisa, Francois; Chevalier, Gerard; Lepareux, Michel.

    1977-01-01

    The TEDEL code is intended for elastic and plastic computation of three-dimensional pipes and frames with possible junction to shells. The structures are described with using assemblies of beam elements, or piping elements such as, curved pipes, 90 0 elbows, tees, any elements, the stiffness properties of which are given to TEDEL. TEDEL allows the dynamic computation of the structures: search of eigenfrequencies and eigenmodes of vibration, time response to any time-dependent canvassing. This response can be obtained either from recombining a number of eigenmodes, or from a direct numerical integration of the dynamics equation. In these last two cases TEDEL accounts for some possible damping. A TEDEL option allows critical buckling loads to be computed (Euler). The structures can offer any shapes comprising any number of materials. The data are readout without any format, and distributed in optional commands with a precise physical meaning: GEOMETRY, MATERIALS, LOAD, COMPUTATION, END. A dynamical memory control allows the size of the routine to be adapted to the problem to be treated. For pipings, an option is intended for an automatic checking of the stress level with regard to the limiting values of the ASME. Geometrical data, node positions, element numbering are given by COCO which also delivers perspective drawings for the structure to be studied. The results on magnetic tapes can be treated by the subroutines ESPACE-VISU-TEMPS [fr

  4. 75 FR 80765 - Hazardous Materials: Adoption of ASME Code Section XII and the National Board Inspection Code

    Science.gov (United States)

    2010-12-23

    ..., Ground Floor, Room W12-140, Routing Symbol M-30, 1200 New Jersey Avenue, SE., Washington, DC 20590. Hand... update current regulations in recognition of the technological enhancements referred to above, maintain... the requirements of Section XII for application of the appropriate Code Symbol stamp; (b) Knowledge of...

  5. Activated sludge models ASM1, ASM2, ASM2d and ASM3

    DEFF Research Database (Denmark)

    Henze, Mogens; Gujer, W.; Mino, T.

    This book has been produced to give a total overview of the Activated Sludge Model (ASM) family at the start of 2000 and to give the reader easy access to the different models in their original versions. It thus presents ASM1, ASM2, ASM2d and ASM3 together for the first time.Modelling of activated...... sludge processes has become a common part of the design and operation of wastewater treatment plants. Today models are being used in design, control, teaching and research.ContentsASM3: Introduction, Comparison of ASM1 and ASM3, ASM3: Definition of compounds in the model, ASM3: Definition of processes...... in the Model, ASM3: Stoichiometry, ASM3: Kinetics, Limitations of ASM3, Aspects of application of ASM3, ASM3C: A Carbon based model, Conclusion ASM 2d: Introduction, Conceptual Approach, ASM 2d, Typical Wastewater Characteristics and Kinetic and Stoichiometric Constants, Limitations, Conclusion ASM 2...

  6. Activated sludge models ASM1, ASM2, ASM2d and ASM3

    DEFF Research Database (Denmark)

    Henze, Mogens; Gujer, W.; Mino, T.

    sludge processes has become a common part of the design and operation of wastewater treatment plants. Today models are being used in design, control, teaching and research.ContentsASM3: Introduction, Comparison of ASM1 and ASM3, ASM3: Definition of compounds in the model, ASM3: Definition of processes...... in the Model, ASM3: Stoichiometry, ASM3: Kinetics, Limitations of ASM3, Aspects of application of ASM3, ASM3C: A Carbon based model, Conclusion ASM 2d: Introduction, Conceptual Approach, ASM 2d, Typical Wastewater Characteristics and Kinetic and Stoichiometric Constants, Limitations, Conclusion ASM 2...... Oxidation Nitrification and Denitrification, Characterization of Wastewater and Estimation of Parameter Values, Typical Parameter Ranges, Default Values, and Effects of Environmental Factors, Assumptions, Restrictions and Constraints, Implementation of the Activated Sludge Model...

  7. Optimized periodic verification testing blended risk and performance-based MOV inservice test program an application of ASME code case OMN-1

    Energy Technology Data Exchange (ETDEWEB)

    Sellers, C.; Fleming, K.; Bidwell, D.; Forbes, P. [and others

    1996-12-01

    This paper presents an application of ASME Code Case OMN-1 to the GL 89-10 Program at the South Texas Project Electric Generating Station (STPEGS). Code Case OMN-1 provides guidance for a performance-based MOV inservice test program that can be used for periodic verification testing and allows consideration of risk insights. Blended probabilistic and deterministic evaluation techniques were used to establish inservice test strategies including both test methods and test frequency. Described in the paper are the methods and criteria for establishing MOV safety significance based on the STPEGS probabilistic safety assessment, deterministic considerations of MOV performance characteristics and performance margins, the expert panel evaluation process, and the development of inservice test strategies. Test strategies include a mix of dynamic and static testing as well as MOV exercising.

  8. Optimized periodic verification testing blended risk and performance-based MOV inservice test program an application of ASME code case OMN-1

    International Nuclear Information System (INIS)

    Sellers, C.; Fleming, K.; Bidwell, D.; Forbes, P.

    1996-01-01

    This paper presents an application of ASME Code Case OMN-1 to the GL 89-10 Program at the South Texas Project Electric Generating Station (STPEGS). Code Case OMN-1 provides guidance for a performance-based MOV inservice test program that can be used for periodic verification testing and allows consideration of risk insights. Blended probabilistic and deterministic evaluation techniques were used to establish inservice test strategies including both test methods and test frequency. Described in the paper are the methods and criteria for establishing MOV safety significance based on the STPEGS probabilistic safety assessment, deterministic considerations of MOV performance characteristics and performance margins, the expert panel evaluation process, and the development of inservice test strategies. Test strategies include a mix of dynamic and static testing as well as MOV exercising

  9. Updating of ASME Nuclear Code Case N-201 to Accommodate the Needs of Metallic Core Support Structures for High Temperature Gas Cooled Reactors Currently in Development

    International Nuclear Information System (INIS)

    Basol, Mit; Kielb, John F.; MuHooly, John F.; Smit, Kobus

    2007-01-01

    On September 29, 2005, ASME Standards Technology, LLC (ASME ST-LLC) executed a multi-year, cooperative agreement with the United States DOE for the Generation IV Reactor Materials project. The project's objective is to update and expand appropriate materials, construction, and design codes for application in future Generation IV nuclear reactor systems that operate at elevated temperatures. Task 4 was embarked upon in recognition of the large quantity of ongoing reactor designs utilizing high temperature technology. Since Code Case N-201 had not seen a significant revision (except for a minor revision in September, 2006 to change the SA-336 forging reference for 304SS and 316SS to SA-965 in Tables 1.2(a) and 1.2(b), and some minor editorial changes) since December 1994, identifying recommended updates to support the current high temperature Core Support Structure (CSS) designs and potential new designs was important. As anticipated, the Task 4 effort identified a number of Code Case N-201 issues. Items requiring further consideration range from addressing apparent inconsistencies in definitions and certain material properties between CC-N-201 and Subsection NH, to inclusion of additional materials to provide the designer more flexibility of design. Task 4 developed a design parameter survey that requested input from the CSS designers of ongoing high temperature gas cooled reactor metallic core support designs. The responses to the survey provided Task 4 valuable input to identify the design operating parameters and future needs of the CSS designers. Types of materials, metal temperature, time of exposure, design pressure, design life, and fluence levels were included in the Task 4 survey responses. The results of the survey are included in this report. This research proves that additional work must be done to update Code Case N-201. Task 4 activities provide the framework for the Code Case N-201 update and future work to provide input on materials. Candidate

  10. Updating of ASME Nuclear Code Case N-201 to Accommodate the Needs of Metallic Core Support Structures for High Temperature Gas Cooled Reactors Currently in Development

    Energy Technology Data Exchange (ETDEWEB)

    Mit Basol; John F. Kielb; John F. MuHooly; Kobus Smit

    2007-05-02

    On September 29, 2005, ASME Standards Technology, LLC (ASME ST-LLC) executed a multi-year, cooperative agreement with the United States DOE for the Generation IV Reactor Materials project. The project's objective is to update and expand appropriate materials, construction, and design codes for application in future Generation IV nuclear reactor systems that operate at elevated temperatures. Task 4 was embarked upon in recognition of the large quantity of ongoing reactor designs utilizing high temperature technology. Since Code Case N-201 had not seen a significant revision (except for a minor revision in September, 2006 to change the SA-336 forging reference for 304SS and 316SS to SA-965 in Tables 1.2(a) and 1.2(b), and some minor editorial changes) since December 1994, identifying recommended updates to support the current high temperature Core Support Structure (CSS) designs and potential new designs was important. As anticipated, the Task 4 effort identified a number of Code Case N-201 issues. Items requiring further consideration range from addressing apparent inconsistencies in definitions and certain material properties between CC-N-201 and Subsection NH, to inclusion of additional materials to provide the designer more flexibility of design. Task 4 developed a design parameter survey that requested input from the CSS designers of ongoing high temperature gas cooled reactor metallic core support designs. The responses to the survey provided Task 4 valuable input to identify the design operating parameters and future needs of the CSS designers. Types of materials, metal temperature, time of exposure, design pressure, design life, and fluence levels were included in the Task 4 survey responses. The results of the survey are included in this report. This research proves that additional work must be done to update Code Case N-201. Task 4 activities provide the framework for the Code Case N-201 update and future work to provide input on materials. Candidate

  11. Review of ASME code criteria for control of primary loads on nuclear piping system branch connections and recommendations for additional development work

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.; Gwaltney, R.C.; Moore, S.E.

    1993-11-01

    This report collects and uses available data to reexamine the criteria for controlling primary loads in nuclear piping branch connections as expressed in Section III of the ASME Boiler and Pressure Vessel Code. In particular, the primary load stress indices given in NB-3650 and NB-3683 are reexamined. The report concludes that the present usage of the stress indices in the criteria equations should be continued. However, the complex treatment of combined branch and run moments is not supported by available information. Therefore, it is recommended that this combined loading evaluation procedure be replaced for primary loads by the separate leg evaluation procedure specified in NC/ND-3653.3(c) and NC/ND-3653.3(d). No recommendation is made for fatigue or secondary load evaluations for Class 1 piping. Further work should be done on the development of better criteria for treatment of combined branch and run moment effects

  12. Replacement of radiography with ultrasonic phased array for feeder tubes in CANDU reactors using ASME code case N-659-2

    International Nuclear Information System (INIS)

    Simmons, R.; Bower, Q.; Arseneau, S.

    2013-01-01

    In this paper we will discuss phased array technology for the replacement of radiography on new construction projects in the nuclear industry. Specifically, through the implementation of A.S.M.E. code N-659-2 and MetaPhase phased array services. Phased Array is not considered a new technique on in service welds in the nuclear industry; however it was unprecedented on new construction welds and required significant investment in regulatory approval (C.N.S.C.), technology research and development, regulatory, client and technician training for successful service implementation. This paper will illustrate the abilities and limitations associated in replacing radiography with MetaPhase, as well as the substantial benefits relative to increased production, improved weld quality, enhanced safety and overall project cost savings. (author)

  13. ASME Based Quality Documentation Guidelines for Power- and Recovery Boilers

    OpenAIRE

    Lappalainen, Tuomas

    2015-01-01

    The goal of this thesis was to create ASME-based quality documentation guidelines for power- and recovery boilers. The client was a large international power- and recovery boiler manufacturer. The content of this thesis is mainly a report of ASME code and its effects on quality documentation. In thesis are widely compared ASME based quality documention differences between PED/EN projects quality documentation. Also ASMEs most important elements for power- and recovery boiler projects needs fo...

  14. Activated sludge models ASM1, ASM2, ASM2d and ASM3

    DEFF Research Database (Denmark)

    Henze, Mogens; Gujer, W.; Mino, T.

    This book has been produced to give a total overview of the Activated Sludge Model (ASM) family at the start of 2000 and to give the reader easy access to the different models in their original versions. It thus presents ASM1, ASM2, ASM2d and ASM3 together for the first time.Modelling of activated......: Introduction, ASM 2, Typical Wastewater Characteristics and Kinetic and Stoichiometric Constants, Wastewater Characterization for Activated Sludge Processes, Calibration of the ASM 2, Model Limitations, Conclusion, Bibliography ASM 1: Introduction, Method of Model Presentation, Model Incorporating Carbon...... Oxidation Nitrification and Denitrification, Characterization of Wastewater and Estimation of Parameter Values, Typical Parameter Ranges, Default Values, and Effects of Environmental Factors, Assumptions, Restrictions and Constraints, Implementation of the Activated Sludge Model...

  15. The safety relief valve handbook design and use of process safety valves to ASME and International codes and standards

    CERN Document Server

    Hellemans, Marc

    2009-01-01

    The Safety Valve Handbook is a professional reference for design, process, instrumentation, plant and maintenance engineers who work with fluid flow and transportation systems in the process industries, which covers the chemical, oil and gas, water, paper and pulp, food and bio products and energy sectors. It meets the need of engineers who have responsibilities for specifying, installing, inspecting or maintaining safety valves and flow control systems. It will also be an important reference for process safety and loss prevention engineers, environmental engineers, and plant and process designers who need to understand the operation of safety valves in a wider equipment or plant design context. . No other publication is dedicated to safety valves or to the extensive codes and standards that govern their installation and use. A single source means users save time in searching for specific information about safety valves. . The Safety Valve Handbook contains all of the vital technical and standards informat...

  16. Cisco ASM Router

    CERN Multimedia

    2001-01-01

    One of the two "ASM/2-32EM" boxes installed in 1988, from "Cisco Systems Inc." - then an unknown 20-employee company in Menlo Park, California (USA). This is one of the first two Cisco boxes to appear in Switzerland, and possibly Europe. The 220v power supply was a special modification made for use at CERN. They supported IP address filtering, which seemed just what CERN needed to help protect the new Cray XMP-48 super computer from network hackers. The two ASM boxes were both routers and terminal servers. They protected a secure private Ethernet segment used by the Cray project, as well as providing secure terminal connections to that segment, including CERN's first dialback terminal service, which allowed Cray and CERN system analysts to work on the machine from home, using another Cisco feature called TACACS. (Kindly offered by B. Segal who discovered this company while at a Usenix Conference in Phoenix, Arizona in June 1987.)

  17. Accelerator System Model (ASM) user manual with physics and engineering model documentation. ASM version 1.0

    International Nuclear Information System (INIS)

    1993-07-01

    The Accelerator System Model (ASM) is a computer program developed to model proton radiofrequency accelerators and to carry out system level trade studies. The ASM FORTRAN subroutines are incorporated into an intuitive graphical user interface which provides for the open-quotes constructionclose quotes of the accelerator in a window on the computer screen. The interface is based on the Shell for Particle Accelerator Related Codes (SPARC) software technology written for the Macintosh operating system in the C programming language. This User Manual describes the operation and use of the ASM application within the SPARC interface. The Appendix provides a detailed description of the physics and engineering models used in ASM. ASM Version 1.0 is joint project of G. H. Gillespie Associates, Inc. and the Accelerator Technology (AT) Division of the Los Alamos National Laboratory. Neither the ASM Version 1.0 software nor this ASM Documentation may be reproduced without the expressed written consent of both the Los Alamos National Laboratory and G. H. Gillespie Associates, Inc

  18. An example of a component replacement when applying ASME N509 and ASME N510 to older ventilation systems

    Energy Technology Data Exchange (ETDEWEB)

    Arndt, T.E. [Westinghouse Hanford Company, Richland, WA (United States)

    1995-02-01

    This paper presents an example of a component replacement (electric heater) when installed in an older ventilation system that was constructed before the issuance of ASME N509{sup 1} and N510{sup 2}. Many of the existing ventilation systems at the Hanford Site were designed, fabricated, and installed before the issuance of ASME N509{sup 1} and N510{sup 2}. Requiring the application of these codes to existing ventilation systems presents challenges to the engineer when design changes are needed. Although it may seem that the application of ASME N509{sup 1} or N510{sup 2} may be a hindrance at times, this does not need to occur. Proper preparation at the start of project or design modifications can minimize frustration to the engineer when it is judged that portions of ASME N509{sup 1} and N510{sup 2} do not apply in a particular application.

  19. The 1997 NRC IST workshops and the status of questions and issues directed to the ASME O and M committee

    International Nuclear Information System (INIS)

    DiBiasio, A.M.

    1998-05-01

    This paper describes the results of the four NRC Inservice Testing (IST) Workshops which were held in early 1997 pertaining to NRC Inspection Procedure P 73756, Inservice Testing of Pumps and Valves. It also presents the status of the ASME code committees' resolution of certain questions forwarded to the ASME by the NRC. These questions relate to code interpretations, inconsistencies in the code, and industry concerns that are most appropriately resolved through the ASME consensus process. The ASME committees reviewed the questions at their December 1997 and March 1998 code meetings. Of particular interest are those questions for which the ASME code committees did not agree with the NRC response. These questions, as well as those which the committees provided some additional insight or input, are presented in this paper

  20. Comparison between ASME and ISO standards on surface texture

    Science.gov (United States)

    Hu, Kai; Jiang, Xiangqian; Liu, Xiaojun; Xu, Zhengao

    2006-11-01

    Surface texture is generally a significant technique requirement of high-tech products. Surface quality information can usually play an increasing role in achieving interoperability among existing products, create order in markets, simplify production and ensure safety. As the most authoritative standard organizations, ASME and ISO services are used throughout the world, their codes and standards influence global manufacturers and consumers. ASME B46.1 is one of many vital tools to promote surface measurement techniques, while ISO has a set standard system for surface measurement, analysis and evaluation. This paper compares the ASME B46.1 (2002) standard (Surface texture: surface roughness, waviness, and lay) with ISO 3274 (1997) standard on methods of surface profiles filtering. It preformed the present research in order to show the latest developments of the ASME B46.1 (2002) in the regime of contact profiling techniques where the degree of measurement control is highly advanced, and a large range of other techniques that present valid and useful descriptions of surface texture. Also, this paper shows the differences of terms, definitions and surface texture parameters between ASME B46.1 (2002) and ISO 4287 (1998). The different evaluation results have been calculated based on above two standards for the same surface data. Obviously, it is necessary to consider the divergence above to develop China's standards (GB) on surface texture.

  1. Rethinking ASME III seismic analysis for piping operability evaluations

    International Nuclear Information System (INIS)

    Adams, T.M.; Stevenson, J.D.

    1994-01-01

    It has been recognized since the mid 1980's that there are very large seismic margins to failure for nuclear piping systems when designed using current industry practice, design criteria, and methods. As a result of this realization there are or have been approximately eighteen initiatives within the ASME , Boiler and Pressure Vessel Code Section III, Division 1, in the form of proposed code cases and proposed code text changes designed to reduce these failure margins to more realistic values. For the most part these initiatives have concentrated on reclassifying seismic inertia stresses in the piping as secondary and increasing the allowable stress limits permitted by Section III of the ASME, Boiler Code. This paper focuses on the application of non-linear spectral analysis methods as a method to reduce the input seismic demand determination and thereby reduce the seismic failure margins. The approach is evaluated using the ASME Boiler Pressure Vessel Code Section III Subgroup on Design benchmark procedure as proposed by the Subgroup's Special Task Group on Integrated Piping Criteria. Using this procedure, criteria are compared to current code criterion and analysis methods, and several other of the currently proposed Boiler and Pressure Vessel, Section III, changes. Finally, the applicability of the non-linear spectral analysis to continued Safe Operation Evaluations is reviewed and discussed

  2. 46 CFR 56.60-1 - Acceptable materials and specifications (replaces 123 and Table 126.1 in ASME B31.1).

    Science.gov (United States)

    2010-10-01

    ... iron Conform to applicable American National Standards or refer to UCI-23 or UCD-23, Sec. VIII of the... acceptable iron castings are in UCI-23 and UCD-23 of section VIII of the ASME Boiler and Pressure Vessel Code... pressure temperature limitations refer to UCI-3 of section VIII of the ASME Boiler and Pressure Vessel Code...

  3. Investigating ASME allowable loads with finite element analyses

    International Nuclear Information System (INIS)

    Mattar Neto, Miguel; Bezerra, Luciano M.; Miranda, Carlos A. de J.; Cruz, Julio R.B.

    1995-01-01

    The evaluation of nuclear components using finite element analysis (FEA) does not generally fall into the shell type verification adopted by the ASME Code. Consequently, the demonstration that the modes of failure are avoided sometimes is not straightforward. Allowable limits, developed by limit load theory, require the computation of shell membrane and bending stresses. How to calculate these stresses from FEA is not necessarily self-evident. One approach to be considered is to develop recommendations in a case-by-case basis for the most common pressure vessel geometries and loads based on comparison between the results of elastic and plastic FEA. In this paper, FE analyses of common 2D and complex 3D geometries are examined and discussed. It will be clear that in the cases studied, stress separation and categorization are not self-evident and simple tasks to undertake. Certain unclear recommendations of ASME Code can lead the stress analyst to non conservative designs as will be demonstrated in this paper. At the endo of this paper, taking into account comparison between elastic and elastic-plastic FE results from ANSYS some observations, suggestions and conclusions about the degree of conservatism of the ASME recommendations will be addressed. (author)

  4. Application procedures and analysis examples of the SIE ASME-NH program

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Seok Hoon; Koo, G. H.; Kim, J. B. [KAERI, Daejeon (Korea, Republic of)

    2010-12-15

    In this report, the design rule of the ASME-NH Code was briefly summarized and the application procedures of SIE ASME-NH program were analysed, the analysis examples were described. The SIE ASME-NH program was developed according to the ASME Code Section III Subsection NH rules to perform the primary stress limits, the accumulated inelastic strain limits and the creep fatigue damage evaluations in the structural design of nuclear power plants operating with high temperatures over creep temperature at normal operating conditions. In the analysis examples, the benchmark problem for the high temperature reactor vessel which was discussed in the SIE ASME-NH user's seminar was described. Also, the preliminary structural analysis of an Advanced Burner Test Reactor internal structure was described. Considering the load combinations of the various cycle types submitted from significant operating conditions, the integrity of a reactor internal structure was reviewed according to the stress and strain limits of the ASME-NH rules and the analysis and evaluation results were summarized

  5. Application procedures and analysis examples of the SIE ASME-NH program

    International Nuclear Information System (INIS)

    Kim, Seok Hoon; Koo, G. H.; Kim, J. B.

    2010-12-01

    In this report, the design rule of the ASME-NH Code was briefly summarized and the application procedures of SIE ASME-NH program were analysed, the analysis examples were described. The SIE ASME-NH program was developed according to the ASME Code Section III Subsection NH rules to perform the primary stress limits, the accumulated inelastic strain limits and the creep fatigue damage evaluations in the structural design of nuclear power plants operating with high temperatures over creep temperature at normal operating conditions. In the analysis examples, the benchmark problem for the high temperature reactor vessel which was discussed in the SIE ASME-NH user's seminar was described. Also, the preliminary structural analysis of an Advanced Burner Test Reactor internal structure was described. Considering the load combinations of the various cycle types submitted from significant operating conditions, the integrity of a reactor internal structure was reviewed according to the stress and strain limits of the ASME-NH rules and the analysis and evaluation results were summarized

  6. Summary of design of nuclear vessels and piping to ASME III (NB, NC, ND) and vessels to BS 5500

    International Nuclear Information System (INIS)

    Harrop, L.P.

    1992-01-01

    There is a hierarchy of design code requirements for pressurised components, starting with non-nuclear codes as the minimum and progressing through the ASME III nuclear Classes 3, 2, 1. In establishing and assessing the safety justifications of nuclear plants it is important to have an appreciation of the gradation of requirements in the ASME III design rules and how these go beyond non-nuclear component design rules. There are two broad aspects to the structural integrity of pressurised components, namely the achievement of integrity and the demonstration of integrity. The technical requirements of design codes are associated with achieving integrity while the documentary aspects are usually associated with demonstrating integrity. In practice documents also have a part in achieving integrity in the communication of information between different organisations and personnel involved in the design process. It is not possible to assign simple numerical measures to the relative integrity afforded by non-nuclear codes and the three Classes of ASME III. Instead it is necessary to compare the different requirements of the rules for the various technical and documentary aspects. This paper summarises the most important technical and documentary aspects of the three Classes of the ASME III Code for vessels and the non-nuclear code BS 5500. A similar summary is also provided for the three Classes of ASME III rules for piping. The intention is that the paper provides a basis for appreciating the relative integrity afforded by these various rules. (author)

  7. ASME Material Challenges for Advanced Reactor Concepts

    Energy Technology Data Exchange (ETDEWEB)

    Piyush Sabharwall; Ali Siahpush

    2013-07-01

    This study presents the material Challenges associated with Advanced Reactor Concept (ARC) such as the Advanced High Temperature Reactor (AHTR). ACR are the next generation concepts focusing on power production and providing thermal energy for industrial applications. The efficient transfer of energy for industrial applications depends on the ability to incorporate cost-effective heat exchangers between the nuclear heat transport system and industrial process heat transport system. The heat exchanger required for AHTR is subjected to a unique set of conditions that bring with them several design challenges not encountered in standard heat exchangers. The corrosive molten salts, especially at higher temperatures, require materials throughout the system to avoid corrosion, and adverse high-temperature effects such as creep. Given the very high steam generator pressure of the supercritical steam cycle, it is anticipated that water tube and molten salt shell steam generators heat exchanger will be used. In this paper, the ASME Section III and the American Society of Mechanical Engineers (ASME) Section VIII requirements (acceptance criteria) are discussed. Also, the ASME material acceptance criteria (ASME Section II, Part D) for high temperature environment are presented. Finally, lack of ASME acceptance criteria for thermal design and analysis are discussed.

  8. ASME and RCC-MR comparison for the prevention of fatigue analysis

    International Nuclear Information System (INIS)

    Autrusson, B.; Acker, D.

    1989-01-01

    The purpose of this survey is to compare the simplified methods, without reference to the safety factor allowed for the mechanical properties. An application of both codes, RCC-MR and ASME, on the design of the wall mock-up of the NET project is made and also an estimation with an elastoplastic analysis. In the case of fatigue analysis according to ASME in the plastic field, the elastic stress is magnified by a K e factor derived from stress variation, S n , disregarding geometrical discontinuities. According to RCC-MR, the elastic maximum strain will magnified by two coefficients accounting for plasticity and variation of Poisson ratio

  9. A Survey of Variable Extragalactic Sources with XTE's All Sky Monitor (ASM)

    Science.gov (United States)

    Jernigan, Garrett

    1998-01-01

    The original goal of the project was the near real-time detection of AGN utilizing the SSC 3 of the ASM on XTE which does a deep integration on one 100 square degree region of the sky. While the SSC never performed sufficiently well to allow the success of this goal, the work on the project has led to the development of a new analysis method for coded aperture systems which has now been applied to ASM data for mapping regions near clusters of galaxies such as the Perseus Cluster and the Coma Cluster. Publications are in preparation that describe both the new method and the results from mapping clusters of galaxies.

  10. Improvement of ASME NH for Grade 91

    Energy Technology Data Exchange (ETDEWEB)

    Bernard Riou

    2007-10-09

    This report has been prepared in the context of Task 3 of the ASME/DOE Gen IV material project. It has been identified that creep-fatigue evaluation procedures presently available in ASME (1) and RCC-MR (2) have been mainly developed for austenitic stainless steels and may not be suitable for cyclic softening materials such as mod 9 Cr 1 Mo steel (grade 91). The aim of this document is, starting from experimental test results, to perform a review of the procedures and, if necessary, provide recommendations for their improvements.

  11. Applications of American design codes for elevated temperature environment

    International Nuclear Information System (INIS)

    Severud, L.K.

    1980-03-01

    A brief summary of the ASME Code rules of Case N-47 is presented. An overview of the typical procedure used to demonstrate Code compliance is provided. Application experience and some examples of detailed inelastic analysis and simplified-approximate methods are given. Recent developments and future trends in design criteria and ASME Code rules are also presented

  12. Activated sludge model No. 2d, ASM2d

    DEFF Research Database (Denmark)

    Henze, M.

    1999-01-01

    The Activated Sludge Model No. 2d (ASM2d) presents a model for biological phosphorus removal with simultaneous nitrification-denitrification in activated sludge systems. ASM2d is based on ASM2 and is expanded to include the denitrifying activity of the phosphorus accumulating organisms (PAOs......). This extension of ASM2 allows for improved modeling of the processes, especially with respect to the dynamics of nitrate and phosphate. (C) 1999 IAWQ Published by Elsevier Science Ltd. All rights reserved....

  13. Radiation-induced temperature shift of thhe ASME KIc curve

    International Nuclear Information System (INIS)

    Nanstad, R.K.; Haggag, F.M.; Iskander, S.K.

    1989-01-01

    The objective of this study was to determine the effects of neutron irradiation on the temperature shift and shape of the K Ic curve described in Sect. XI of the ASME Boiler and pressure Vessel Code. Two submerged-arc welds with copper contents of 0.23 and 0.31 wt % were commercially fabricated in 215-mm-thick plate. Charpy impact, tensile, dropweight, and compact specimens up to 203.2 mm thick were fabricated and tested to provide a large data for unirradiated material. Similar specimens with compacts up to 101.6 mm thick, irradiated at about 288 degree C to a mean fluence of about 1.6 times 10 19 neutrons/cm 2 in the Oak Ridge Research Reactor, were tested to provide a similarly large data base with which to evaluate the temperature shift and shape of the ASME K Ic curves. Testing was performed by both Oak Ridge National Laboratory and Materials Engineering Associates. Both linear-elastic and elastic-plastic fracture mechanics techniques were used to analyze test results. 3 refs., 4 figs., 1 tab

  14. Proceedings: 2000 ASME/EPRI Radwaste Workshop

    International Nuclear Information System (INIS)

    2001-01-01

    Nuclear utilities are continually evaluating methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has added increased emphasis to this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technological and managerial improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

  15. Proceedings: 2001 ASME/EPRI Radwaste Workshop

    International Nuclear Information System (INIS)

    2001-01-01

    Nuclear utilities continually evaluate methods to improve operations and reduce costs associated with radioactive waste management. The continuing deregulation process has increased the emphasis on this activity. The Annual ASME/EPRI Workshop facilitates this effort by communicating technology and management improvements throughout the industry. This workshop, restricted to utility radwaste professionals, also serves to communicate practical in-plant improvements with the opportunity to discuss them in detail

  16. Interpreting ASME limits and philosophy in FEA of pressure vessel parts

    International Nuclear Information System (INIS)

    Bezerra, L.M.; Cruz, J.R.B.; Miranda, C.A.J.; Neto, M.M.

    1995-01-01

    In recent years there has been an effort to interpret finite element (FE) stress results on the light of the ASME B and PV rules and philosophy. Many task groups have issued guidelines on stress linearization and classifications. All those attempts have come up trying to cope modern FE techniques with the rules imposed by the ASME Code. This paper is an independent contribution to the Pressure Vessel Research Council (PVRC) groups which are studying the stress classification and the failure mechanism in a FE framework. This work tries to complement the interesting work by Hollinger and Hechmer presented in the PVP-94 in Minneapolis. In that paper, the authors examined a typical support skirt and showed relations between the skirt collapse load obtained by finite element analysis and the loads allowed from the ASME stress limits. To complement such paper, in the present article, different skirt geometry configurations are analyzed. The configurations here investigated consist of similar support skirts but with different angles of attachments between cylinder and cone parts. It will be possible to observe the influence of the bending stress in the collapse load and its relation to the allowable loads inferred from the ASME limits. A pressure vessel with torispherical head under internal pressure is also examined. Using elastic and limit load FEA, the present paper determines the collapse loads of the configurations. It sets up the relations between these collapse loads, stress categories, and limits dictated by the ASME Code Subsection NB. On the light of NB rules and philosophy, this paper shows how different methods of stress assessment, classification, and limits may influence in the design of a pressure vessel

  17. Report on ANSI/ASME nuclear air and gas treatment standards for nuclear power plants

    International Nuclear Information System (INIS)

    Fish, J.F.

    1979-01-01

    Original N Committee, N45-8, has completed and published through the approved American National Standards Institute process two Standards, N-509 and N-510. This committee has been dissolved and replaced by ASME Committee on Nuclear Air and Gas Treatment with expanded scope to cover not only air cleaning, but thermal treatment equipment. Current efforts are directed to produce Code documents rather than Standards type publications. This report summarizes changed scope, current organization and sub-committee coverage areas

  18. 76 FR 36231 - American Society of Mechanical Engineers (ASME) Codes and New and Revised ASME Code Cases

    Science.gov (United States)

    2011-06-21

    ... Agencywide Documents Access and Management System (ADAMS): Publicly available documents created or received... necessary for a more predictable process. The NRC performed a Lean Six Sigma review of its 10 CFR 50.55a... a nuclear power plant, the manufacturer would have to build at least two additional production...

  19. 75 FR 24323 - American Society of Mechanical Engineers (ASME) Codes and New and Revised ASME Code Cases

    Science.gov (United States)

    2010-05-04

    ... provisions, delete specific provisions, and/or clarify them to narrow the applicability of the provision. The... the ``Weld leg use of stress dimensions''. indices used for welds in piping design under Subarticles... visual examination of insulated components in systems borated for the purpose of controlling reactivity...

  20. Temporal Deductive Verification of Basic ASM Models

    OpenAIRE

    Daho, Hocine El-Habib; University of Oran; Benhamamouch, Djillali; University of Oran

    2010-01-01

    Abstract State Machines (ASMs, for short) provide a practical new computational model which has been applied in the area of software engineering for systems design and analysis. However, reasoning about ASM models occurs, not within a formal deductive system, but basically in the classical informal proofs style of mathematics. Several formal verification approaches for proving correctness of ASM models have been investigated. In this paper we consider the use of the TLA+logic for the deductive...

  1. AsmL Specification of a Ptolemy II Scheduler

    DEFF Research Database (Denmark)

    Lázaro Cuadrado, Daniel; Koch, Peter; Ravn, Anders Peter

    2003-01-01

    Ptolemy II is a tool that combines different computational models for simulation and design of embedded systems. AsmL is a software specification language based on the Abstract State Machine formalism. This paper reports on development of an AsmL model of the Synchronous Dataflow domain scheduler...

  2. 1985 ASME-EPRI radwaste workshop: proceedings

    International Nuclear Information System (INIS)

    Coplan, B.V.

    1985-07-01

    The proceedings of the seventh ASME/EPRI jointly sponsored radwaste workshop are presented. The workshop presentations and discussion sessions addressed the following pertinent issues: Meeting Radwaste Regulatory Requirements; Mobile Services; and Radwaste Equipment and Reducing Costs. Interest in meeting regulatory requirements centered on the various aspects of 10CFR61. Proper sampling, compliance methodology, hydrogen generation in stored radwaste and process control programs were the major topics of discussion. Use of mobile services provided by outside organizations is increasing. An extensive summary of available mobile services was presented in the areas of radwaste processing, solidification and decontamination, as well as information on special on-site storage containers. Under the areas of radwaste equipment and reducing costs, the principal items were the status of a mobile incinerator for Commonwealth Edison, establishment of a deminimis level for waste at Ginna, resin volume reduction at Brunswick and a dry active waste segregation program at TVA. Presentations were also made on radwaste transportation and burial and on two planned regional radwaste incineration facilities. The meeting concluded with an open discussion period for all participants on a variety of radwaste items

  3. Auriculoterapia en pacientes asmáticos

    Directory of Open Access Journals (Sweden)

    Adolfo González Salvador

    1997-04-01

    Full Text Available Se realiza un estudio para evaluar la eficacia de la auriculopuntura en 30 asmáticos del área de salud de Aguada de Pasajeros, durante los meses de noviembre de 1992 a abril de 1993. El tratamiento se aplicó durante un mes, con seguimiento durante los 5 meses posteriores. Se observó una disminución en la frecuencia, intensidad y duración de las crisis de asma; la mayoría de los pacientes tuvo una evolución satisfactoria y no se presentaron complicaciones. Se concluye que la auriculoterapia es un método útil en pacientes con asma bronquial debido a su eficacia e inocuidadA study was conducted to evaluate the efficacy of auriculopuncture in 30 asthmatic patients from the health area of Aguada de Pasajeros between November, 1992, and April, 1993. The treatment was applied for a month, with a follow-up during the next 5 months. It was observed a reduction in the frequency, intensity and duration of the asthma crises. Most of the patients had a satisfactory evolution and there were no complications. It is concluded that auriculotherapy is a useful method for patients with bronchial asthma due to its effectiveness and innocuousness.

  4. ASTM and ASME-BPE Standards--Complying with the Needs of the Pharmaceutical Industry.

    Science.gov (United States)

    Huitt, William M

    2011-01-01

    Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and standards and then modifying them in order to meet the more stringent requirements of the Food and Drug Administration (FDA). In 1997 the American Society of Mechanical Engineers (ASME) published the first Bioprocessing Equipment (BPE) Standard. Through harmonization efforts this relatively new standard has brought together, scrutinized, and refined industry accepted methodologies together with FDA compliance requirements, and has established an American National Standard that provides a comprehensive set of standards that are integral to the pharmaceutical industry. This article describes various American National Standards, including those developed and published by the American Society for Testing and Materials (ASTM), and how they apply to the pharmaceutical industry. It goes on to discuss the harmonization effort that takes place between the various standards developers in an attempt to prevent conflicts and omissions between the many standards. Also included are examples of tables and figures taken from the ASME-BPE Standard. These examples provide the reader with insight to the relevant content of the ASME-BPE Standard. Designing and building a pharmaceutical facility requires the owner, engineer of record, and constructor to be knowledgeable with regard to the industry codes and standards that apply to this effort. Up until 1997 there were no industry standards directed at the needs and requirements of the pharmaceutical industry. Prior to that time it was a patchwork effort at resourcing and adopting nonpharmaceutical-related codes and

  5. Regulatory Safety Issues in the Structural Design Criteria of ASME Section III Subsection NH and for Very High Temperatures for VHTR and GEN IV

    International Nuclear Information System (INIS)

    O'Donnell, William J.; Griffin, Donald S.

    2007-01-01

    The objective of this task is to identify issues relevant to ASME Section III, Subsection NH [1], and related Code Cases that must be resolved for licensing purposes for VHTGRs (Very High Temperature Gas Reactor concepts such as those of PBMR, Areva, and GA); and to identify the material models, design criteria, and analysis methods that need to be added to the ASME Code to cover the unresolved safety issues. Subsection NH was originally developed to provide structural design criteria and limits for elevated-temperature design of Liquid Metal Fast Breeder Reactor (LMFBR) systems and some gas-cooled systems. The U.S. Nuclear Regulatory Commission (NRC) and its Advisory Committee for Reactor Safeguards (ACRS) reviewed the design limits and procedures in the process of reviewing the Clinch River Breeder Reactor (CRBR) for a construction permit in the late 1970s and early 1980s, and identified issues that needed resolution. In the years since then, the NRC and various contractors have evaluated the applicability of the ASME Code and Code Cases to high-temperature reactor designs such as the VHTGRs, and identified issues that need to be resolved to provide a regulatory basis for licensing. This Report describes: (1) NRC and ACRS safety concerns raised during the licensing process of CRBR , (2) how some of these issues are addressed by the current Subsection NH of the ASME Code; and (3) the material models, design criteria, and analysis methods that need to be added to the ASME Code and Code Cases to cover unresolved regulatory issues for very high temperature service.

  6. Penetration of ASM 981 in canine skin: a comparative study.

    Science.gov (United States)

    Gutzwiller, Meret E Ricklin; Reist, Martin; Persohn, Elke; Peel, John E; Roosje, Petra J

    2006-01-01

    ASM 981 has been developed for topical treatment of inflammatory skin diseases. It specifically inhibits the production and release of pro-inflammatory cytokines. We measured the skin penetration of ASM 981 in canine skin and compared penetration in living and frozen skin. To make penetration of ASM 981 visible in dog skin, tritium labelled ASM 981 was applied to a living dog and to defrosted skin of the same dog. Using qualitative autoradiography the radioactive molecules were detected in the lumen of the hair follicles until the infundibulum, around the superficial parts of the hair follicles and into a depth of the dermis of 200 to 500 microm. Activity could not be found in deeper parts of the hair follicles, the dermis or in the sebaceous glands. Penetration of ASM 981 is low in canine skin and is only equally spread in the upper third of the dermis 24 hours after application. Penetration in frozen skin takes even longer than in living canine skin but shows the same distribution.

  7. Index to place of publication of ASME Papers, 1978--1988

    International Nuclear Information System (INIS)

    Youngen, G.K.

    1990-06-01

    This index is a list of American Society of Mechanical Engineers (ASME) Papers that are reprinted in the ASME Transactions series of journals. ASME Papers are often cited only by their paper number, making it difficult to determine if the article has ever appeared in print in the journal literature. This index will be useful for tracking down those papers published as journal articles by the ASME. It will also serve as a guide for retention for subscribers to the ASME Papers and Transaction Series. Paper numbers that appear in the journals may be weeded from the collection of ASME Papers

  8. Flanged joints with contact outside the bolt circle: ASME Part B design rules

    International Nuclear Information System (INIS)

    Rodabaugh, E.C.; Moore, S.E.

    1976-05-01

    The ASME Boiler and Pressure Vessel Code, Section VIII, Division 1, gives rules which are subdivided into ''Part A'' and ''Part B''. Part A covers flanged joints where contact between flanges occurs through a gasket located inside the bolt holes. Part B covers flanged joints with contact outside the bolt holes. This report (a) summarizes the theory for Part B flanged joints, (b) presents examples which show the significant differences between Part A flanged joints and Part B flanged joints, (c) presents the available test data relevant to the characteristics of Part B flanged joints, (d) gives listings of two computer programs which can be used to evaluate the characteristics of Part B flanged joints, and (e) gives recommendations for Code revisions and other aspects of Part B flanged-joint design

  9. AsmL Specification of a Ptolemy II Scheduler

    DEFF Research Database (Denmark)

    Lázaro Cuadrado, Daniel; Koch, Peter; Ravn, Anders Peter

    2003-01-01

    Ptolemy II is a tool that combines different computational models for simulation and design of embedded systems. AsmL is a software specification language based on the Abstract State Machine formalism. This paper reports on development of an AsmL model of the Synchronous Dataflow domain scheduler...... of Ptolemy II. By building this model we can give precise semantics to the implementation. Furthermore it allows us to isolate the scheduling problem from the tool and make the potential parallelism of the implementation explicit. The model is executable and is tested against the implementation...

  10. The human ASM (adult skeletal muscle) gene: expression and chromosomal assignment to 11p15.

    Science.gov (United States)

    Leibovitch, M P; Nguyen, V C; Gross, M S; Solhonne, B; Leibovitch, S A; Bernheim, A

    1991-11-14

    A rat adult skeletal muscle probe (Asm15) originated from a rhabdomyosarcoma was used to isolate the human homologous sequence from a placenta cDNA library. Among several positive clones the longest EcoRI-EcoRI insert (ASM1) obtained was 1875 bp long with 72% homology with rat Asm15 cDNA sequence. Important variations of ASM1 RNA level were observed in different adult skeletal muscles. Expression of a 29kD ASM1 protein was demonstrated in human adult skeletal muscle lysates using an antiserum (PB1579) raised against the C terminal region of the rat Asm15 protein. The human ASM gene was assigned by somatic cell analysis with human (ASM1) and rat (Asm15) probes to chromosome 11, and by in situ hybridization with the human probe to 11p15, a chromosome region involved in human embryonal rhabdomyosarcomas. Except for the presence of a HindII restriction site, the results obtained for the restriction map and the sequence of ASM1 cDNA (data not shown) exhibited extensive homology with the human H19 DNA sequence which have been mapped with a mouse probe also in 11p15. This suggests that ASM/Asm and H19 may represent the same sequence (in this hypothesis the presence of the supplementary HindII site in our ASM1 probe is explained by polymorphic variability). However it was reported that human and mouse H19 mRNA did not encode for a protein but acted as an RNA molecule whereas in our present study ASM protein was detected in human adult skeletal muscle. This could be explained by important regulation of ASM protein expression during development and cell differentiation. However we cannot exclude for the different species studied (mouse, rat, and man) the hypothesis that H19 and ASM/Asm mRNA may represent two distinct messengers from the same gene or even from duplicated genes.

  11. ASME stress linearization and classification - a discussion based on a case study

    International Nuclear Information System (INIS)

    Miranda, Carlos A. de J.; Faloppa, Altair A.; Mattar Neto, Miguel; Fainer, Gerson

    2011-01-01

    The ASME code, specially in its Nuclear Division (Subsection NB - Class I Components), gives some recommendations to the structural analyst on how to perform the verifications required to prove the design as good as the by-analysis prevented failures modes. Each of these failure modes has specific stress limits which are established based on simple but conservative hypothesis like the material perfectly plastic behavior and the shell theory with its typical membrane and bending stresses with linear distribution along the thickness. Other detail to keep in mind is the code distinction between primary and secondary stresses (respectively, stress that came due to equilibrium and due to displacement compatibility). In general, the numerical models used in the analyses are developed with plane or 3D solid elements and due this fact no direct comparison with the code limits can be done and, besides that, the programs do not distinguish between primary and secondary stresses. Mostly, the later are produced due to the temperature variation but they also appear near discontinuities. Sometimes, this classification is not so clear or direct. To perform the required ASME Code verifications the analyst should obtain the membrane and bending stresses from the plane or 3-D model which is called stress linearization and, also, should classify them as primary and secondary. (The excess between the maximum stress at a point and the sum of these linearized values is called peak stress and is included in the fatigue verification.) This task, most of the time is not a simple one due to the nature of the involved load and/or the complex geometry under analysis. In fact, there are several studies discussing on how to perform these stress classification and linearization. The present paper shows a discussion on how to perform these verifications based on a generic geometry found in many plants, from petrochemical to nuclear, which emphasizes some of theses issues. (author)

  12. 14 CFR 330.31 - What data must air carriers submit concerning ASMs or RTMs?

    Science.gov (United States)

    2010-01-01

    ... combination passenger/cargo carrier, you must have submitted your August 2001 total completed ASM report to... correct an error that you document to the Department, you must not alter the ASM or RTM reports you...

  13. Asm-1(+), a Neurospora Crassa Gene Related to Transcriptional Regulators of Fungal Development

    OpenAIRE

    Aramayo, R.; Peleg, Y.; Addison, R.; Metzenberg, R.

    1996-01-01

    This report describes the identification, cloning, and molecular analysis of Asm-1(+) (Ascospore maturation 1), the Neurospora crassa homologue of the Aspergillus nidulans stuA (stunted A) gene. The Asm-1(+) gene is constitutively transcribed and encodes an abundant, nucleus-localized 68.5-kD protein. The protein product of Asm-1(+) (ASM-1), contains a potential DNA-binding motif present in related proteins from A. nidulans (StuA), Candida albicans (EFGTF-1), and Saccharomyces cerevisiae (Phd...

  14. Abelian Sandpile Model (ASM) and Infinite Volume Limit

    Indian Academy of Sciences (India)

    Self Organised Criticality (SOC). SOC- dynamics drive a system towards stationary state characterized by power law correlations in space and time. SOC- was proposed by [BTW 87,88] as a mechanism which could explain occurrence of fractal structures in diverse natural phenomena. ASM is a simple model where SOC ...

  15. A strategy for implementation of experience based seismic equipment qualification in IEEE and ASME industry standards

    International Nuclear Information System (INIS)

    Adams, T.M.

    1996-01-01

    In the past 20 years, extensive data on the performance of mechanical and electric equipment during actual strong motion earthquakes and seismic qualification tests has been accumulated. Recognizing that an experience based approach provides a technically sound and cost effective method for the seismic qualification of some or certain equipment, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment established a Special Working Group to investigate the incorporation of experienced based methods into the industry consensus codes and standards currently used in the seismic qualification of Seismic Category Nuclear Power Plant equipment. This paper presents the strategy (course of action) which was developed by the Special Working Group for meeting this objective of incorporation of experience based seismic qualification standards used in the design and seismic qualification of seismic category nuclear power plant equipment. This strategy was recommended to both chartering organizations, the IEEE Nuclear Power Engineering Committee and the ASME Committee on Qualification of Mechanical Equipment for their consideration and implementation. The status of the review and implementation of the Special Working Group's recommended strategy by the sponsoring organization is also discussed

  16. Relationship between various pressure vessel and piping codes

    International Nuclear Information System (INIS)

    Canonico, D.A.

    1976-01-01

    Section VIII of the ASME Code provides stress allowable values for material specifications that are provided in Section II Parts A and B. Since the adoption of the ASME Code over 60 years ago the incidence of failure has been greatly reduced. The Codes are currently based on strength criteria and advancements in the technology of fracture toughness and fracture mechanics should permit an even greater degree of reliability and safety. This lecture discusses the various Sections of the Code. It describes the basis for the establishment of design stress allowables and promotes the idea of the use of fracture mechanics

  17. Interim status report on the revision of ASME PTC 12.1 -- closed feedwater heaters

    International Nuclear Information System (INIS)

    Stellern, J.L.; Hoobler, J.V.; Milton, J.W.; Welch, T.; Kona, C.; Thompson, H.N.; Tsou, J.L.

    1993-01-01

    The ASME Performance Test Code (PTC) 12.1-1978 for the performance testing of feedwater heaters is being revised extensively and updated. The committee anticipates that the final draft of the proposed Code will be ready for industry review in 1993. This Code revision will greatly enhance the usefulness and cost effectiveness of feedwater heater performance testing. This paper has been prepared to report on the progress of the committee and to disseminate information on the nature of the revision. Included in this paper are some of the notable changes intended for the Code. The most extensive change is the calculation method, which is described in step-by-step detail. An approach is also described for using ultrasonic flow techniques to test individual or split-string feedwater heaters, when flow nozzles are not available. Additionally some educational information on the use and limitations of ultrasonic measurement instrumentation is included. Discussion is also included on the required uncertainty analysis. 3 refs., 2 figs., 2 tabs

  18. Bibliometric Analyses Reveal Patterns of Collaboration between ASMS Members

    Science.gov (United States)

    Palmblad, Magnus; van Eck, Nees Jan

    2018-01-01

    We have explored the collaborative network of the current American Society for Mass Spectrometry (ASMS) membership using bibliometric methods. The analysis shows that 4249 members are connected in a single, large, co-authorship graph, including the majority of the most published authors in the field of mass spectrometry. The map reveals topographical differences between university groups and national laboratories, and that the co-authors with the strongest links have long worked together at the same location. We have collected and summarized information on the geographical distribution of members, showing a high coverage of active researchers in North America and Western Europe. Looking at research fields, we could also identify a number of new or `hot' topics among ASMS members. Interactive versions of the maps are available on-line at https://goo.gl/UBNFMQ (collaborative network) and https://goo.gl/WV25vm (research topics).

  19. Bibliometric Analyses Reveal Patterns of Collaboration between ASMS Members.

    Science.gov (United States)

    Palmblad, Magnus; van Eck, Nees Jan

    2018-03-01

    We have explored the collaborative network of the current American Society for Mass Spectrometry (ASMS) membership using bibliometric methods. The analysis shows that 4249 members are connected in a single, large, co-authorship graph, including the majority of the most published authors in the field of mass spectrometry. The map reveals topographical differences between university groups and national laboratories, and that the co-authors with the strongest links have long worked together at the same location. We have collected and summarized information on the geographical distribution of members, showing a high coverage of active researchers in North America and Western Europe. Looking at research fields, we could also identify a number of new or 'hot' topics among ASMS members. Interactive versions of the maps are available on-line at https://goo.gl/UBNFMQ (collaborative network) and https://goo.gl/WV25vm (research topics). Graphical Abstract ᅟ.

  20. Bibliometric Analyses Reveal Patterns of Collaboration between ASMS Members

    Science.gov (United States)

    Palmblad, Magnus; van Eck, Nees Jan

    2018-03-01

    We have explored the collaborative network of the current American Society for Mass Spectrometry (ASMS) membership using bibliometric methods. The analysis shows that 4249 members are connected in a single, large, co-authorship graph, including the majority of the most published authors in the field of mass spectrometry. The map reveals topographical differences between university groups and national laboratories, and that the co-authors with the strongest links have long worked together at the same location. We have collected and summarized information on the geographical distribution of members, showing a high coverage of active researchers in North America and Western Europe. Looking at research fields, we could also identify a number of new or `hot' topics among ASMS members. Interactive versions of the maps are available on-line at https://goo.gl/UBNFMQ (collaborative network) and https://goo.gl/WV25vm (research topics). [Figure not available: see fulltext.

  1. A Life-Cycle Risk-Informed Systems Structured Nuclear Code

    International Nuclear Information System (INIS)

    Hill, Ralph S. III

    2002-01-01

    Current American Society of Mechanical Engineers (ASME) nuclear codes and standards rely primarily on deterministic and mechanistic approaches to design. The design code is a separate volume from the code for inservice inspections and both are separate from the standards for operations and maintenance. The ASME code for inservice inspections and code for nuclear plant operations and maintenance have adopted risk-informed methodologies for inservice inspection, preventive maintenance, and repair and replacement decisions. The American Institute of Steel Construction and the American Concrete Institute have incorporated risk-informed probabilistic methodologies into their design codes. It is proposed that the ASME nuclear code should undergo a planned evolution that integrates the various nuclear codes and standards and adopts a risk-informed approach across a facility life-cycle - encompassing design, construction, operation, maintenance and closure. (author)

  2. ASM-024, a piperazinium compound, promotes the in vitro relaxation of β2-adrenoreceptor desensitized tracheas.

    Science.gov (United States)

    Israël-Assayag, Evelyne; Beaulieu, Marie-Josée; Cormier, Yvon

    2015-01-01

    Inhaled β2-adrenoreceptor agonists are widely used in asthma and chronic obstructive pulmonary disease (COPD) for bronchoconstriction relief. β2-Adrenoreceptor agonists relax airway smooth muscle cells via cyclic adenosine monophosphate (cAMP) mediated pathways. However, prolonged stimulation induces functional desensitization of the β2-adrenoreceptors (β2-AR), potentially leading to reduced clinical efficacy with chronic or prolonged administration. ASM-024, a small synthetic molecule in clinical stage development, has shown activity at the level of nicotinic receptors and possibly at the muscarinic level and presents anti-inflammatory and bronchodilator properties. Aerosolized ASM-024 reduces airway resistance in mice and promotes in-vitro relaxation of tracheal and bronchial preparations from animal and human tissues. ASM-024 increased in vitro relaxation response to maximally effective concentration of short-acting beta-2 agonists in dog and human bronchi. Although the precise mechanisms by which ASM-024 promotes airway smooth muscle (ASM) relaxation remain unclear, we hypothesized that ASM-024 will attenuate and/or abrogate agonist-induced contraction and remain effective despite β2-AR tachyphylaxis. β2-AR tachyphylaxis was induced with salbutamol, salmeterol and formoterol on guinea pig tracheas. The addition of ASM-024 relaxed concentration-dependently intact or β2-AR desensitized tracheal rings precontracted with methacholine. ASM-024 did not induce any elevation of intracellular cAMP in isolated smooth muscle cells; moreover, blockade of the cAMP pathway with an adenylate cyclase inhibitor had no significant effect on ASM-024-induced guinea pig trachea relaxation. Collectively, these findings show that ASM-024 elicits relaxation of β2-AR desensitized tracheal preparations and suggest that ASM-024 mediates smooth muscle relaxation through a different target and signaling pathway than β2-adrenergic receptor agonists. These findings suggest ASM-024

  3. Simulation analysis of ASM/Takács models in the BSM1 configuration.

    Science.gov (United States)

    Sorour, M T; Bahgat, L M F

    2006-10-01

    The present paper summarizes the outlines of a simulation analysis study conducted on the BSM1 (formerly the COST benchmark) configuration using activated sludge models (ASM1, ASM2d and ASM3) coupled to Takács settler model. The prime objective was to develop reliable simulation software programs to implement these complex models according to the working conditions of a realistic plant. The analysis focused on comparing the steady state predictions of models ASM1/ ASM3 when imposed to pulse/ step type disturbances on wastewater characteristics and control variables, then on assessing the capability of the simulated configuration for bio-P removal using model ASM2d. Section 1 of the paper briefly presents problem definition/ solution approach while section 2 demonstrates some examples showing the main indications of the simulation analysis. ASM1/ ASM3 predictions indicate the presence of some significant differences between both models that could be related to their underlying concepts. ASM2d simulations show that adverse effects on the permissible limit of effluent's ammonia concentration should be expected when the plant is operated to achieve dual nutrient removal.

  4. 10 CFR 50.55a - Codes and standards.

    Science.gov (United States)

    2010-01-01

    ... not affected by these limitations. (ii) Pressure-retaining welds in ASME Code Class 1 piping (applies... 10 Energy 1 2010-01-01 2010-01-01 false Codes and standards. 50.55a Section 50.55a Energy NUCLEAR... specified in § 50.55, except that each combined license for a boiling or pressurized water-cooled nuclear...

  5. ASM Based Synthesis of Handwritten Arabic Text Pages

    Directory of Open Access Journals (Sweden)

    Laslo Dinges

    2015-01-01

    Full Text Available Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

  6. ASM Based Synthesis of Handwritten Arabic Text Pages.

    Science.gov (United States)

    Dinges, Laslo; Al-Hamadi, Ayoub; Elzobi, Moftah; El-Etriby, Sherif; Ghoneim, Ahmed

    2015-01-01

    Document analysis tasks, as text recognition, word spotting, or segmentation, are highly dependent on comprehensive and suitable databases for training and validation. However their generation is expensive in sense of labor and time. As a matter of fact, there is a lack of such databases, which complicates research and development. This is especially true for the case of Arabic handwriting recognition, that involves different preprocessing, segmentation, and recognition methods, which have individual demands on samples and ground truth. To bypass this problem, we present an efficient system that automatically turns Arabic Unicode text into synthetic images of handwritten documents and detailed ground truth. Active Shape Models (ASMs) based on 28046 online samples were used for character synthesis and statistical properties were extracted from the IESK-arDB database to simulate baselines and word slant or skew. In the synthesis step ASM based representations are composed to words and text pages, smoothed by B-Spline interpolation and rendered considering writing speed and pen characteristics. Finally, we use the synthetic data to validate a segmentation method. An experimental comparison with the IESK-arDB database encourages to train and test document analysis related methods on synthetic samples, whenever no sufficient natural ground truthed data is available.

  7. Limitations of ASM1 and ASM3: a comparison based on batch oxygen uptake rate profiles from different full-scale wastewater treatment plants.

    Science.gov (United States)

    Guisasola, A; Sin, G; Baeza, J A; Carrera, J; Vanrolleghem, P A

    2005-01-01

    The two most popular models for the description of the biological COD removal are ASM1 and ASM3. However, some numerical inconsistencies arise when using these models to interpret the data obtained in short-term respirometric batch experiments. In this study, both models are fitted to four different respirometric batch profiles obtained with biomass from different WWTP. The parameter estimation results and the practical (local) identifiability are analysed, and the limitations of both models are discussed. The growth yield obtained by fitting ASM1 to the short-term respirometric batch profiles is higher than the default one, as well as the storage yield obtained by fitting ASM3 is lower than the default one. Based on these values, possible improvements to the modelling of the biological COD removal, such as the inclusion of simultaneous growth and storage on external substrate, are proposed.

  8. Integrin and GPCR Crosstalk in the Regulation of ASM Contraction Signaling in Asthma.

    Science.gov (United States)

    Teoh, Chun Ming; Tam, John Kit Chung; Tran, Thai

    2012-01-01

    Airway hyperresponsiveness (AHR) is one of the cardinal features of asthma. Contraction of airway smooth muscle (ASM) cells that line the airway wall is thought to influence aspects of AHR, resulting in excessive narrowing or occlusion of the airway. ASM contraction is primarily controlled by agonists that bind G protein-coupled receptor (GPCR), which are expressed on ASM. Integrins also play a role in regulating ASM contraction signaling. As therapies for asthma are based on symptom relief, better understanding of the crosstalk between GPCRs and integrins holds good promise for the design of more effective therapies that target the underlying cellular and molecular mechanism that governs AHR. In this paper, we will review current knowledge about integrins and GPCRs in their regulation of ASM contraction signaling and discuss the emerging concept of crosstalk between the two and the implication of this crosstalk on the development of agents that target AHR.

  9. ASM1-based activated sludge model with biopolymer kinetics for integrated simulation of membrane bioreactors for wastewater treatment

    OpenAIRE

    Janus, Tomasz; Ulanicki, Bogumil

    2015-01-01

    This paper presents an activated sludge model suitable for modelling membrane bioreactors (MBRs) for wastewater treatment. The model, later referred to as combined EPS and SMP production ASM1-based model (CES-ASM1), extends Activated Sludge Model No. 1 (ASM1) with biokinetics of two types of bacterial biopolymers: soluble microbial products (SMP) and extracellular polymeric substances (EPS). The biopolymer kinetics in CES-ASM1 are, in their majority, borrowed from Laspidou and Rittmann[1] ...

  10. Regulation of dynein-mediated autophagosomes trafficking by ASM in CASMCs.

    Science.gov (United States)

    Xu, Ming; Zhang, Qiufang; Li, Pin-Lan; Nguyen, Thaison; Li, Xiang; Zhang, Yang

    2016-01-01

    Acid sphingomyelinase (ASM; gene symbol Smpd1) has been shown to play a crucial role in autophagy maturation by controlling lysosomal fusion with autophagosomes in coronary arterial smooth muscle cells (CASMCs). However, the underlying molecular mechanism by which ASM controls autophagolysosomal fusion remains unknown. In primary cultured CASMCs, lysosomal Ca2+ induced by 7-ketocholesterol (7-Ket, an atherogenic stimulus and autophagy inducer) was markedly attenuated by ASM deficiency or TRPML1 gene silencing suggesting that ASM signaling is required for TRPML1 channel activity and subsequent lysosomal Ca(2+) release. In these CASMCs, ASM deficiency or TRPML1 gene silencing markedly inhibited 7-Ket-induced dynein activation. In addition, 7-Ket-induced autophagosome trafficking, an event associated with lysosomal Ca(2+) release and dynein activity, was significantly inhibited in ASM-deficient (Smpd1(-/-)) CASMCs compared to that in Smpd1(+/+) CASMCs. Finally, overexpression of TRPML1 proteins restored 7-Ket-induced lysosomal Ca(2+) release and autophagosome trafficking in Smpd1-/- CASMCs. Collectively, these results suggest that ASM plays a critical role in regulating lysosomal TRPML1-Ca(2+) signaling and subsequent dynein-mediated autophagosome trafficking, which leads its role in controlling autophagy maturation in CASMCs under atherogenic stimulation.

  11. [Ca2+]i oscillations in ASM: relationship with persistent airflow obstruction in asthma.

    Science.gov (United States)

    Sweeney, David; Hollins, Fay; Gomez, Edith; Saunders, Ruth; Challiss, R A John; Brightling, Christopher E

    2014-07-01

    The cause of airway smooth muscle (ASM) hypercontractility in asthma is not fully understood. The relationship of spontaneous intracellular calcium oscillation frequency in ASM to asthma severity was investigated. Oscillations were increased in subjects with impaired lung function abolished by extracellular calcium removal, attenuated by caffeine and unaffected by verapamil or nitrendipine. Whether modulation of increased spontaneous intracellular calcium oscillations in ASM from patients with impaired lung function represents a therapeutic target warrants further investigation. © 2014 The Authors. Respirology published by Wiley Publishing Asia Pty Ltd on behalf of Asian Pacific Society of Respirology.

  12. Report on FY15 alloy 617 code rules development

    Energy Technology Data Exchange (ETDEWEB)

    Sham, Sam [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jetter, Robert I [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hollinger, Greg [Becht Engineering Co., Inc., Liberty Corner, NJ (United States); Pease, Derrick [Becht Engineering Co., Inc., Liberty Corner, NJ (United States); Carter, Peter [Stress Engineering Services, Inc., Houston, TX (United States); Pu, Chao [Univ. of Tennessee, Knoxville, TN (United States); Wang, Yanli [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-09-01

    Due to its strength at very high temperatures, up to 950°C (1742°F), Alloy 617 is the reference construction material for structural components that operate at or near the outlet temperature of the very high temperature gas-cooled reactors. However, the current rules in the ASME Section III, Division 5 Subsection HB, Subpart B for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 650°C (1200°F) (Corum and Brass, Proceedings of ASME 1991 Pressure Vessels and Piping Conference, PVP-Vol. 215, p.147, ASME, NY, 1991). The rationale for this exclusion is that at higher temperatures it is not feasible to decouple plasticity and creep, which is the basis for the current simplified rules. This temperature, 650°C (1200°F), is well below the temperature range of interest for this material for the high temperature gas-cooled reactors and the very high temperature gas-cooled reactors. The only current alternative is, thus, a full inelastic analysis requiring sophisticated material models that have not yet been formulated and verified. To address these issues, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (EPP) analysis methods applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature (Carter, Jetter and Sham, Proceedings of ASME 2012 Pressure Vessels and Piping Conference, papers PVP 2012 28082 and PVP 2012 28083, ASME, NY, 2012), and have been recently revised to incorporate comments and simplify their application. Background documents have been developed for these two code cases to support the ASME Code committee approval process. These background documents for the EPP strain limits and creep-fatigue code cases are documented in this report.

  13. The ASM Curriculum Guidelines for Undergraduate Microbiology: A Case Study of the Advocacy Role of Societies in Reform Efforts.

    Science.gov (United States)

    Horak, Rachel E A; Merkel, Susan; Chang, Amy

    2015-05-01

    A number of national reports, including Vision and Change in Undergraduate Biology Education: A Call to Action, have called for drastic changes in how undergraduate biology is taught. To that end, the American Society for Microbiology (ASM) has developed new Curriculum Guidelines for undergraduate microbiology that outline a comprehensive curriculum for any undergraduate introductory microbiology course or program of study. Designed to foster enduring understanding of core microbiology concepts, the Guidelines work synergistically with backwards course design to focus teaching on student-centered goals and priorities. In order to qualitatively assess how the ASM Curriculum Guidelines are used by educators and learn more about the needs of microbiology educators, the ASM Education Board distributed two surveys to the ASM education community. In this report, we discuss the results of these surveys (353 responses). We found that the ASM Curriculum Guidelines are being implemented in many different types of courses at all undergraduate levels. Educators indicated that the ASM Curriculum Guidelines were very helpful when planning courses and assessments. We discuss some specific ways in which the ASM Curriculum Guidelines have been used in undergraduate classrooms. The survey identified some barriers that microbiology educators faced when trying to adopt the ASM Curriculum Guidelines, including lack of time, lack of financial resources, and lack of supporting resources. Given the self-reported challenges to implementing the ASM Curriculum Guidelines in undergraduate classrooms, we identify here some activities related to the ASM Curriculum Guidelines that the ASM Education Board has initiated to assist educators in the implementation process.

  14. Comparisons of ANS, ASME, AWS, and NFPA standards cited in the NRC standard review plan, NUREG-0800, and related documents

    Energy Technology Data Exchange (ETDEWEB)

    Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Spiesman, J.B. [Pacific Northwest Lab., Richland, WA (United States)

    1995-11-01

    This report provides the results of comparisons of the cited and latest versions of ANS, ASME, AWS and NFPA standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC`s Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review.

  15. Comparisons of ANS, ASME, AWS, and NFPA standards cited in the NRC standard review plan, NUREG-0800, and related documents

    International Nuclear Information System (INIS)

    Ankrum, A.R.; Bohlander, K.L.; Gilbert, E.R.; Spiesman, J.B.

    1995-11-01

    This report provides the results of comparisons of the cited and latest versions of ANS, ASME, AWS and NFPA standards cited in the NRC Standard Review Plan for the Review of Safety Analysis Reports for Nuclear Power Plants (NUREG 0800) and related documents. The comparisons were performed by Battelle Pacific Northwest Laboratories in support of the NRC's Standard Review Plan Update and Development Program. Significant changes to the standards, from the cited version to the latest version, are described and discussed in a tabular format for each standard. Recommendations for updating each citation in the Standard Review Plan are presented. Technical considerations and suggested changes are included for related regulatory documents (i.e., Regulatory Guides and the Code of Federal Regulations) citing the standard. The results and recommendations presented in this document have not been subjected to NRC staff review

  16. The Bauschinger Effect in Autofrettaged Tubes- A Comparison of Models Including the ASME Code

    National Research Council Canada - National Science Library

    Parker, Anthony

    1998-01-01

    .... For many years workers have acknowledged the probable influence of the Bauschinger effect which serves to reduce the yield strength in compression as a result of prior tensile plastic overload...

  17. High Level Analysis, Design and Validation of Distributed Mobile Systems with CoreASM

    Science.gov (United States)

    Farahbod, R.; Glässer, U.; Jackson, P. J.; Vajihollahi, M.

    System design is a creative activity calling for abstract models that facilitate reasoning about the key system attributes (desired requirements and resulting properties) so as to ensure these attributes are properly established prior to actually building a system. We explore here the practical side of using the abstract state machine (ASM) formalism in combination with the CoreASM open source tool environment for high-level design and experimental validation of complex distributed systems. Emphasizing the early phases of the design process, a guiding principle is to support freedom of experimentation by minimizing the need for encoding. CoreASM has been developed and tested building on a broad scope of applications, spanning computational criminology, maritime surveillance and situation analysis. We critically reexamine here the CoreASM project in light of three different application scenarios.

  18. 115-year-old society knows how to reach young scientists: ASM Young Ambassador Program.

    Science.gov (United States)

    Karczewska-Golec, Joanna

    2015-12-25

    With around 40,000 members in more than 150 countries, American Society for Microbiology (ASM) faces the challenge of meeting very diverse needs of its increasingly international members base. The newly launched ASM Young Ambassador Program seeks to aid the Society in this effort. Equipped with ASM conceptual support and financing, Young Ambassadors (YAs) design and pursue country-tailored approaches to strengthen the Society's ties with local microbiological communities. In a trans-national setting, the active presence of YAs at important scientific events, such as 16th European Congress on Biotechnology, forges new interactions between ASM and sister societies. The paper presents an overview of the Young Ambassadors-driven initiatives at both global and country levels, and explores the topic of how early-career scientists can contribute to science diplomacy and international relations. Copyright © 2014 Elsevier B.V. All rights reserved.

  19. Measurement of large ground motions with the ASM gage

    International Nuclear Information System (INIS)

    Wright, B.L.; Alrick, K.R.; Fritz, J.N.

    1994-01-01

    Conversion of the energy from undergound explosions to distant seismic signals involves hydrodynamic flows sampling a wide range of pressures. For lower pressures a larger portion of the initial wave motion must be measured to obtain definitive results. The intermediate pressure range, where the initial wave is strong enough to destroy most instrumentation but does not contain definitive information in its initial amplitude, presents special difficulties. We present design considerations for an experiment implementing the ASM gage principle (induction of eddy currents in a moving conducting plate) that can sample wave motion for many milliseconds. In essence we hang a large metal plate (large in area) on a wall and watch the free-surface release. This is not an in-itu measurement of the wave profile because the incoming wave is modififed by the release propagating backward from the wall. However, this a relatively clean modification of the incoming wave and is a situation commonly handled in many shock-wave experiments. copyright American Institute of Physics

  20. SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

    Science.gov (United States)

    Luger, T; Van Leent, E J; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knop, J; Knulst, A C; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; Van Der Valk, P G; Bos, J D

    2001-04-01

    SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy of SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6% and 1.0% in the treatment of patients with atopic dermatitis and to select the concentration to be used in phase III studies. This was a double-blind, randomized, parallel-group, multicentre dose-finding study. A total of 260 patients were randomly assigned to treatment with SDZ ASM 981 cream at concentrations of 0.05%, 0.2%, 0.6%, or 1.0%, matching vehicle cream, or the internal control 0.1% betamethasone-17-valerate cream (BMV). Treatment was given twice daily for up to 3 weeks. A clear dose-response relationship for SDZ ASM 981 was evident, with 0.2%, 0.6% and 1.0% SDZ ASM 981 creams all being significantly more effective than vehicle (P = 0.041, 0.001 and 0.008, respectively) in terms of baseline to end-point changes in the Eczema Area Severity Index (EASI) and pruritus score. The 1.0% cream was the most effective SDZ ASM 981 concentration. BMV was more effective than the SDZ ASM 981 creams tested in this study. It appears that the efficacy plateau was not reached with the SDZ ASM 981 creams within 3 weeks treatment. SDZ ASM 981 was well tolerated. Burning or a feeling of warmth were the only adverse events reported more frequently in the 0.6% and 1.0% SDZ ASM 981 treatment groups than in the vehicle treatment group (42.9%, 48.9% and 34.9%, respectively). Few systemic adverse events were reported during the study (headache was the most frequent systemic event reported by 15 of 252 patients) and none was considered to be related to treatment. The local tolerability profile of the 1.0% cream was similar to that of the lower concentrations. 1.0% SDZ ASM 981 cream, which was shown to be safe, well tolerated and

  1. cASM: Obtaining the Ability to Capture Requirements Information Across the Installation Contracting Support Community

    Science.gov (United States)

    2016-04-22

    social impact to the local populace, but this effect must be closely tied to the strategic effects desired.19 An ill planned acquisition could lead to...21 EVALUATION – CONTINGENCY ACQUISTION SUPPORT MODEL (cASM...iv LIST OF FIGURES Figure 1: Top Twenty Contingency Acquisition Expenditures by PSC…………….……….18 Figure 2: Evaluation of cASM

  2. Acid Sphingomyelinase (ASM is a Negative Regulator of Regulatory T Cell (Treg Development

    Directory of Open Access Journals (Sweden)

    Yuetao Zhou

    2016-08-01

    Full Text Available Background/Aims: Regulatory T cell (Treg is required for the maintenance of tolerance to various tissue antigens and to protect the host from autoimmune disorders. However, Treg may, indirectly, support cancer progression and bacterial infections. Therefore, a balance of Treg function is pivotal for adequate immune responses. Acid sphingomyelinase (ASM is a rate limiting enzyme involved in the production of ceramide by breaking down sphingomyelin. Previous studies in T-cells have suggested that ASM is involved in CD28 signalling, T lymphocyte granule secretion, degranulation, and vesicle shedding similar to the formation of phosphatidylserine-exposing microparticles from glial cells. However, whether ASM affects the development of Treg has not yet been described. Methods: Splenocytes, isolated Naive T lymphocytes and cultured T cells were characterized for various immune T cell markers by flow cytometery. Cell proliferation was measured by Carboxyfluorescein succinimidyl ester (CFSE dye, cell cycle analysis by Propidium Iodide (PI, mRNA transcripts by q-RT PCR and protein expression by Western Blotting respectively. Results: ASM deficient mice have higher number of Treg compared with littermate control mice. In vitro induction of ASM deficient T cells in the presence of TGF-β and IL-2 lead to a significantly higher number of Foxp3+ induced Treg (iTreg compared with control T-cells. Further, ASM deficient iTreg has less AKT (serine 473 phosphorylation and Rictor levels compared with control iTreg. Ceramide C6 led to significant reduction of iTreg in both ASM deficient and WT mice. The reduction in iTreg leads to induction of IL-1β, IL-6 and IL-17 but not IFN-γ mRNA levels. Conclusion: ASM is a negative regulator of natural and iTreg.

  3. Acid Sphingomyelinase (ASM) is a Negative Regulator of Regulatory T Cell (Treg) Development.

    Science.gov (United States)

    Zhou, Yuetao; Salker, Madhuri S; Walker, Britta; Münzer, Patrick; Borst, Oliver; Gawaz, Meinrad; Gulbins, Erich; Singh, Yogesh; Lang, Florian

    2016-01-01

    Regulatory T cell (Treg) is required for the maintenance of tolerance to various tissue antigens and to protect the host from autoimmune disorders. However, Treg may, indirectly, support cancer progression and bacterial infections. Therefore, a balance of Treg function is pivotal for adequate immune responses. Acid sphingomyelinase (ASM) is a rate limiting enzyme involved in the production of ceramide by breaking down sphingomyelin. Previous studies in T-cells have suggested that ASM is involved in CD28 signalling, T lymphocyte granule secretion, degranulation, and vesicle shedding similar to the formation of phosphatidylserine-exposing microparticles from glial cells. However, whether ASM affects the development of Treg has not yet been described. Splenocytes, isolated Naive T lymphocytes and cultured T cells were characterized for various immune T cell markers by flow cytometery. Cell proliferation was measured by Carboxyfluorescein succinimidyl ester (CFSE) dye, cell cycle analysis by Propidium Iodide (PI), mRNA transcripts by q-RT PCR and protein expression by Western Blotting respectively. ASM deficient mice have higher number of Treg compared with littermate control mice. In vitro induction of ASM deficient T cells in the presence of TGF-β and IL-2 lead to a significantly higher number of Foxp3+ induced Treg (iTreg) compared with control T-cells. Further, ASM deficient iTreg has less AKT (serine 473) phosphorylation and Rictor levels compared with control iTreg. Ceramide C6 led to significant reduction of iTreg in both ASM deficient and WT mice. The reduction in iTreg leads to induction of IL-1β, IL-6 and IL-17 but not IFN-γ mRNA levels. ASM is a negative regulator of natural and iTreg. © 2016 The Author(s) Published by S. Karger AG, Basel.

  4. Inhibition of allergen-induced basophil activation by ASM-024, a nicotinic receptor ligand.

    Science.gov (United States)

    Watson, Brittany M; Oliveria, John Paul; Nusca, Graeme M; Smith, Steven G; Beaudin, Sue; Dua, Benny; Watson, Rick M; Assayag, Evelynne Israël; Cormier, Yvon F; Sehmi, Roma; Gauvreau, Gail M

    2014-01-01

    Nicotinic acetylcholine receptors (nAChRs) were identified on eosinophils and shown to regulate inflammatory responses, but nAChR expression on basophils has not been explored yet. We investigated surface receptor expression of nAChR α4, α7 and α1/α3/α5 subunits on basophils. Furthermore, we examined the effects of ASM-024, a synthetic nicotinic ligand, on in vitro anti-IgE and in vivo allergen-induced basophil activation. Basophils were enriched from the peripheral blood of allergic donors and the expression of nAChR subunits and muscarinic receptors was determined. Purified basophils were stimulated with anti-IgE in the presence of ASM-024 with or without muscarinic or nicotinic antagonists for the measurement of CD203c expression and histamine release. The effect of 9 days of treatment with 50 and 200 mg ASM-024 on basophil CD203c expression was examined in the blood of mild allergic asthmatics before and after allergen inhalation challenge. nAChR α4, α7 and α1/α3/α5 receptor subunit expression was detected on basophils. Stimulation of basophils with anti-IgE increased CD203c expression and histamine release, which was inhibited by ASM-024 (10(-5) to 10(-)(3) M, p ASM-024 was reversed in the presence of muscarinic and nicotinic antagonists. In subjects with mild asthma, ASM-024 inhalation significantly inhibited basophil CD203c expression measured 24 h after allergen challenge (p = 0.03). This study shows that ASM-024 inhibits IgE- and allergen-induced basophil activation through both nicotinic and muscarinic receptors, and suggests that ASM-024 may be an efficacious agent for modulating allergic asthma responses. © 2015 S. Karger AG, Basel.

  5. Revision of the ASME nuclear quality assurance standard and its historical background

    International Nuclear Information System (INIS)

    Suzuki, Tetsuya

    2009-01-01

    ASME NQA-1-2008 'Quality Assurance Requirements for Nuclear Facility Applications' will be endorsed by US NRC by the end of 2009. This standard will apply to design, construction and operation of nuclear power plants newly erected in USA. It is important to Japanese vendors developing nuclear business in USA. Historical background, significance of revision and main revised points of the ASME nuclear quality assurance standard are described in the present paper. (T. Tanaka)

  6. Structural analysis program of plant piping system. Introduction of AutoPIPE V8i new feature. JSME PPC-class 2 piping code

    International Nuclear Information System (INIS)

    Motohashi, Kazuhiko

    2009-01-01

    After an integration with ADLPipe, AutoPIPE V8i (ver.9.1) became the structural analysis program of plant piping system featured with analysis capability for the ASME NB Class 1 and JSME PPC-Class 2 piping codes including ASME NC Class 2 and ASME ND Class 3. This article described analysis capability for the JSME PPC-Class 2 piping code as well as new general features such as static analysis up to 100 thermal, 10 seismic and 10 wind load cases including different loading scenarios and pipe segment edit function: join, split, reverse and re-order segments. (T. Tanaka)

  7. A Minimal Path Searching Approach for Active Shape Model (ASM)-based Segmentation of the Lung.

    Science.gov (United States)

    Guo, Shengwen; Fei, Baowei

    2009-03-27

    We are developing a minimal path searching method for active shape model (ASM)-based segmentation for detection of lung boundaries on digital radiographs. With the conventional ASM method, the position and shape parameters of the model points are iteratively refined and the target points are updated by the least Mahalanobis distance criterion. We propose an improved searching strategy that extends the searching points in a fan-shape region instead of along the normal direction. A minimal path (MP) deformable model is applied to drive the searching procedure. A statistical shape prior model is incorporated into the segmentation. In order to keep the smoothness of the shape, a smooth constraint is employed to the deformable model. To quantitatively assess the ASM-MP segmentation, we compare the automatic segmentation with manual segmentation for 72 lung digitized radiographs. The distance error between the ASM-MP and manual segmentation is 1.75 ± 0.33 pixels, while the error is 1.99 ± 0.45 pixels for the ASM. Our results demonstrate that our ASM-MP method can accurately segment the lung on digital radiographs.

  8. Assessment of crack-like flaws - Comparison of procedures in BS 7910, API 579-1/ASME FFS-1, RSE-M AND FITNET

    International Nuclear Information System (INIS)

    Chaudouet, A.

    2007-01-01

    Among all Fitness For Service Codes enabling to assess flaws in metallic structures and to evaluate their remaining life, new editions of the most important ones at the international level have been issued recently. The latest edition of BS 7910 in United Kingdom has been released in October 2005. In the USA, API and ASME have edited a new standard in 2007, API579-1/ASME FFS-1, dedicated to pressure equipment. In France, the rules concerning the of Light Water Reactors, RSE-M, have been updated in 2005. Finally, in Europe, the FITNET network is writing a document based on BS 7910 but extended with the most recent results in this domain. Rules given in these documents to assess crack-like flaws with respect to fracture and fatigue propagation are presented. They are compared in order to point out the most interesting aspects of each ones and to identify those which could be generalized. An example assessed with the above mentioned 'Codes' enlightens the differences in the results with respect to the 'Code' used. (author) [fr

  9. 78 FR 79363 - Hazardous Materials: Adoption of ASME Code Section XII and the National Board Inspection Code

    Science.gov (United States)

    2013-12-30

    ... would reduce fuel costs. Entities that repair tanks and third-party inspectors would have to be trained... Transport Tanks, and Part 3, Supplement 6: Repair, Alteration, and Modification of DOT Transport Tanks go to... design, material, construction, repair and inspection of transport tanks. Incorporating Section XII and...

  10. Equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos

    Directory of Open Access Journals (Sweden)

    Marta Cristina Rodrigues da Silva

    2013-06-01

    Full Text Available O objetivo foi analisar e comparar o equilíbrio corporal em crianças e adolescentes asmáticos e não asmáticos. Fizeram parte do grupo de estudos 24 sujeitos com idades de 7 a 14 anos divididos em dois grupos: grupo asmático e grupo controle. Para avaliação do equilíbrio corporal utilizou-se uma plataforma de força. Foram utilizadas as condições, olhos abertos e fechados com três tentativas aleatórias, com duração de 30 segundos cada uma. Os resultados apontaram diferença significativa entre os grupos, no teste de equilíbrio com olhos abertos apresentando maior amplitude de deslocamento na direção ântero-posterior (COPap (p = 0,04, e médio lateral (COPml (p = 0,02 no grupo asmático. Enquanto que no teste com olhos fechados a diferença foi significante apenas na amplitude de deslocamento ântero-posterior (COPap (p = 0,02 e Área de Elipse (p=0,03. Desse modo, a asma com suas limitações e consequências parece influenciar negativamente no equilíbrio corporal de seus portadores quando comparados com crianças sem a patologia e da mesma faixa etária.

  11. Design evaluation on sodium piping system and comparison of the design codes

    International Nuclear Information System (INIS)

    Lee, Dong Won; Jeong, Ji Young; Lee, Yong Bum; Lee, Hyeong Yeon

    2015-01-01

    A large-scale sodium test loop of STELLA-1 (Sodium integral effect test loop for safety simulation and assessment) with two main piping systems has been installed at KAERI. In this study, design evaluations on the main sodium piping systems in STELLA-1 have been conducted according to the DBR (design by rule) codes of the ASME B31.1 and RCC-MRx RB-3600. In addition, design evaluations according to the DBA (design by analysis) code of the ASME Section III Subsection NB-3200 have been conducted. The evaluation results for the present piping systems showed that results from the DBR codes were more conservative than those from the DBA code, and among the DBR codes, the non-nuclear code of the ASME B31.1 was more conservative than the French nuclear DBR code of the RCC-MRx RB-3600. The conservatism on the DBR codes of the ASME B31.1 and RCC-MRx RB-3600 was quantified based on the present sodium piping analyses.

  12. OM Code Requirements For MOVs -- OMN-1 and Appendix III

    Energy Technology Data Exchange (ETDEWEB)

    Kevin G. DeWall

    2011-08-01

    The purpose or scope of the ASME OM Code is to establish the requirements for pre-service and in-service testing of nuclear power plant components to assess their operational readiness. For MOVs this includes those that perform a specific function in shutting down a reactor to the safe shutdown condition, maintaining the safe shutdown condition, and mitigating the consequences of an accident. This paper will present a brief history of industry and regulatory activities related to MOVs and the development of Code requirements to address weaknesses in earlier versions of the OM Code. The paper will discuss the MOV requirements contained in the 2009 version of ASME OM Code, specifically Mandatory Appendix III and OMN-1, Revision 1.

  13. 46 CFR 56.01-5 - Adoption of ASME B31.1 for power piping, and other standards.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 2 2010-10-01 2010-10-01 false Adoption of ASME B31.1 for power piping, and other... ENGINEERING PIPING SYSTEMS AND APPURTENANCES General § 56.01-5 Adoption of ASME B31.1 for power piping, and... accordance with ASME B31.1 (incorporated by reference; see 46 CFR 56.01-2), as limited, modified, or replaced...

  14. Roles of the Outer Membrane Protein AsmA of Salmonella enterica in the Control of marRAB Expression and Invasion of Epithelial Cells▿

    OpenAIRE

    Prieto, Ana I.; Hernández, Sara B.; Cota, Ignacio; Pucciarelli, M. Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

    2009-01-01

    A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S....

  15. Code boiler and pressure vessel life assessment

    International Nuclear Information System (INIS)

    Farr, J.R.

    1992-01-01

    In the United States of America and in Canada, laws and controls for determining life assessment for continued operation of equipment exist only for those pressure vessels built to Section III and evaluated according to Section XI. In this presentation, some of those considerations which are made in the USA and Canada for deciding on life or condition assessment of boilers and pressure vessels designed and constructed to other sections of the ASME Boiler and Pressure Vessel Code are reviewed. Life assessment or condition assesssment is essential in determining what is necessary for continued operation. With no ASME rules being adopted by laws or regulations, other than OSHA in the USA and similar environmental controls in Canada, to control life assessment for continued operation, the equipment owner must decide if assessment is to be done and how much to do. Some of those considerations are reviewed along with methods and procedures to make an assessment along with a discussion of where the ASME B and PV Code currently stands regarding continued operation. (orig.)

  16. Science of Casting and Solidification: ASM Handbook Contributions — Honoring Professor Doru Michael Stefanescu

    Science.gov (United States)

    Lupulescu, Afina; Henry, Scott; Marken, Karen; Lampman, Steven

    Many of the metal casting processes are still empirical in nature. Many others are deeply rooted in mathematics and therefore, suitable for modeling. Science of casting and solidification is a major technical asset for foundry operations and of extreme importance in understanding different length scales microstructural changes and evolution as well as developing new processes and materials. In his attempt to describe combinations of solidification theory, research results and industrial practice, Professor Doru Michael Stefanescu (ASM Fellow, 1997) has made tremendous contributions to the field. Many of his views on casting and solidification are valued as important impacts within professional environments such as TMS and ASM International. He has written many articles for the ASM Handbook series on subjects including basic metallurgy of cast iron, compacted graphite irons, solidification, thermodynamic properties of iron-base alloys, and computational modeling. He was also Volume Chair for Volume 15: Casting, of the 9th Edition Metals Handbook.

  17. Corticosteroids reduce IL-6 in ASM cells via up-regulation of MKP-1.

    Science.gov (United States)

    Quante, Timo; Ng, Yee Ching; Ramsay, Emma E; Henness, Sheridan; Allen, Jodi C; Parmentier, Johannes; Ge, Qi; Ammit, Alaina J

    2008-08-01

    The mechanisms by which corticosteroids reduce airway inflammation are not completely understood. Traditionally, corticosteroids were thought to inhibit cytokines exclusively at the transcriptional level. Our recent evidence, obtained in airway smooth muscle (ASM), no longer supports this view. We have found that corticosteroids do not act at the transcriptional level to reduce TNF-alpha-induced IL-6 gene expression. Rather, corticosteroids inhibit TNF-alpha-induced IL-6 secretion by reducing the stability of the IL-6 mRNA transcript. TNF-alpha-induced IL-6 mRNA decays at a significantly faster rate in ASM cells pretreated with the corticosteroid dexamethasone (t(1/2) = 2.4 h), compared to vehicle (t(1/2) = 9.0 h; P ASM cells.

  18. Cyclin D1 in ASM Cells from Asthmatics Is Insensitive to Corticosteroid Inhibition.

    Science.gov (United States)

    Allen, Jodi C; Seidel, Petra; Schlosser, Tobias; Ramsay, Emma E; Ge, Qi; Ammit, Alaina J

    2012-01-01

    Hyperplasia of airway smooth muscle (ASM) is a feature of the remodelled airway in asthmatics. We examined the antiproliferative effectiveness of the corticosteroid dexamethasone on expression of the key regulator of G(1) cell cycle progression-cyclin D1-in ASM cells from nonasthmatics and asthmatics stimulated with the mitogen platelet-derived growth factor BB. While cyclin D1 mRNA and protein expression were repressed in cells from nonasthmatics in contrast, cyclin D1 expression in asthmatics was resistant to inhibition by dexamethasone. This was independent of a repressive effect on glucocorticoid receptor translocation. Our results corroborate evidence demonstrating that corticosteroids inhibit mitogen-induced proliferation only in ASM cells from subjects without asthma and suggest that there are corticosteroid-insensitive proliferative pathways in asthmatics.

  19. More on fatigue verification of Class 1 nuclear power piping according to ASME BPV III NB-3600

    International Nuclear Information System (INIS)

    Zeng, Lingfu; Dahlström, Lars; Jansson, Lennart G.

    2011-01-01

    In this paper, fatigue verification of Class 1 nuclear power piping according to ASME Boiler and Pressure Vessel Code, Section III, NB-3600, and relevant issues that are often discussed in connection to the power uprate of several Swedish BWR reactors in recent years, are dealt with. Key parameters involved in the fatigue verification, i.e. the alternating stress intensity S alt , the penalty factor K e and the cumulative damage factor U, and relevant computational procedures applicable for the assessment of low-cycle fatigue failure using strain-controlled data, are particularly addressed. A so-called simplified elastic-plastic discontinuity analysis for alternative verification when basic fatigue requirements found unsatisfactory, and the procedures provided in NB-3600 for evaluating the alternating stress intensity S alt , are reviewed in detail. Our emphasis is placed on other procedures alternative to the simplified elastic-plastic discontinuity analysis. A more in-depth discussion is given to an alternative suggested earlier by the authors using nonlinear finite element analyses. This paper is a continuation of our work presented in ICONE16/17/18, which attempted to categorize design rules in the code into linear design rules and non-linear design rules and to clarify corresponding design requirements and finite element analyses, in particular, those non-linear ones. (author)

  20. ASM LabCap's contributions to disease surveillance and the International Health Regulations (2005).

    Science.gov (United States)

    Specter, Steven; Schuermann, Lily; Hakiruwizera, Celestin; Sow, Mah-Séré Keita

    2010-12-03

    The revised International Health Regulations [IHR(2005)], which requires the Member States of the World Health Organization (WHO) to develop core capacities to detect, assess, report, and respond to public health threats, is bringing new challenges for national and international surveillance systems. As more countries move toward implementation and/or strengthening of their infectious disease surveillance programs, the strengthening of clinical microbiology laboratories becomes increasingly important because they serve as the first line responders to detect new and emerging microbial threats, re-emerging infectious diseases, the spread of antibiotic resistance, and the possibility of bioterrorism. In fact, IHR(2005) Core Capacity #8, "Laboratory", requires that laboratory services be a part of every phase of alert and response.Public health laboratories in many resource-constrained countries require financial and technical assistance to build their capacity. In recognition of this, in 2006, the American Society for Microbiology (ASM) established an International Laboratory Capacity Building Program, LabCap, housed under the ASM International Board. ASM LabCap utilizes ASM's vast resources and its membership's expertise-40,000 microbiologists worldwide-to strengthen clinical and public health laboratory systems in low and low-middle income countries. ASM LabCap's program activities align with HR(2005) by building the capability of resource-constrained countries to develop quality-assured, laboratory-based information which is critical to disease surveillance and the rapid detection of disease outbreaks, whether they stem from natural, deliberate or accidental causes.ASM LabCap helps build laboratory capacity under a cooperative agreement with the U.S. Centers for Disease Control and Prevention (CDC) and under a sub-contract with the Program for Appropriate Technology in Health (PATH) funded by the United States Agency for International Development (USAID

  1. Structural and functional analysis of the ASM p.Ala359Asp mutant that causes acid sphingomyelinase deficiency.

    Science.gov (United States)

    Acuña, Mariana; Castro-Fernández, Víctor; Latorre, Mauricio; Castro, Juan; Schuchman, Edward H; Guixé, Victoria; González, Mauricio; Zanlungo, Silvana

    2016-10-21

    Niemann-Pick disease (NPD) type A and B are recessive hereditary disorders caused by deficiency in acid sphingomyelinase (ASM). The p.Ala359Asp mutation has been described in several patients but its functional and structural effects in the protein are unknown. In order to characterize this mutation, we modeled the three-dimensional ASM structure using the recent available crystal of the mammalian ASM as a template. We found that the p.Ala359Asp mutation is localized in the hydrophobic core and far from the sphingomyelin binding site. However, energy function calculations using statistical potentials indicate that the mutation causes a decrease in ASM stability. Therefore, we investigated the functional effect of the p.Ala359Asp mutation in ASM expression, secretion, localization and activity in human fibroblasts. We found a 3.8% residual ASM activity compared to the wild-type enzyme, without changes in the other parameters evaluated. These results support the hypothesis that the p.Ala359Asp mutation causes structural alterations in the hydrophobic environment where ASM is located, decreasing its enzymatic activity. A similar effect was observed in other previously described NPDB mutations located outside the active site of the enzyme. This work shows the first full size ASM mutant model describe at date, providing a complete analysis of the structural and functional effects of the p.Ala359Asp mutation over the stability and activity of the enzyme. Copyright © 2016 Elsevier Inc. All rights reserved.

  2. Roles of the outer membrane protein AsmA of Salmonella enterica in the control of marRAB expression and invasion of epithelial cells.

    Science.gov (United States)

    Prieto, Ana I; Hernández, Sara B; Cota, Ignacio; Pucciarelli, M Graciela; Orlov, Yuri; Ramos-Morales, Francisco; García-del Portillo, Francisco; Casadesús, Josep

    2009-06-01

    A genetic screen for suppressors of bile sensitivity in DNA adenine methylase (dam) mutants of Salmonella enterica serovar Typhimurium yielded insertions in an uncharacterized locus homologous to the Escherichia coli asmA gene. Disruption of asmA suppressed bile sensitivity also in phoP and wec mutants of S. enterica and increased the MIC of sodium deoxycholate for the parental strain ATCC 14028. Increased levels of marA mRNA were found in asmA, asmA dam, asmA phoP, and asmA wec strains of S. enterica, suggesting that lack of AsmA activates expression of the marRAB operon. Hence, asmA mutations may enhance bile resistance by inducing gene expression changes in the marRAB-controlled Mar regulon. In silico analysis of AsmA structure predicted the existence of one transmembrane domain. Biochemical analysis of subcellular fractions revealed that the asmA gene of S. enterica encodes a protein of approximately 70 kDa located in the outer membrane. Because AsmA is unrelated to known transport and/or efflux systems, we propose that activation of marRAB in asmA mutants may be a consequence of envelope reorganization. Competitive infection of BALB/c mice with asmA(+) and asmA isogenic strains indicated that lack of AsmA attenuates Salmonella virulence by the oral route but not by the intraperitoneal route. Furthermore, asmA mutants showed a reduced ability to invade epithelial cells in vitro.

  3. SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis.

    NARCIS (Netherlands)

    Luger, T.; Leent, E.J. van; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A.C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; Valk, P.G.M. van der; Bos, J.D.

    2001-01-01

    BACKGROUND: SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. OBJECTIVES: This study was designed to determine

  4. Parameter subset selection for the dynamic calibration of activated sludge models (ASMs): experience versus systems analysis

    DEFF Research Database (Denmark)

    Ruano, MV; Ribes, J; de Pauw, DJW

    2007-01-01

    In this work we address the issue of parameter subset selection within the scope of activated sludge model calibration. To this end, we evaluate two approaches: (i) systems analysis and (ii) experience-based approach. The evaluation has been carried out using a dynamic model (ASM2d) calibrated...

  5. Reaction invariant-based reduction of the activated sludge model ASM1 for batch applications

    DEFF Research Database (Denmark)

    Santa Cruz, Judith A.; Mussati, Sergio F.; Scenna, Nicolás J.

    2016-01-01

    to batch activated sludge processes described by the Activated Sludge Model No. 1 (ASM1) for carbon and nitrogen removal. The objective of the model reduction is to describe the exact dynamics of the states predicted by the original model with a lower number of ODEs. This leads to a reduction...

  6. SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

    NARCIS (Netherlands)

    Luger, T.; van Leent, E. J.; Graeber, M.; Hedgecock, S.; Thurston, M.; Kandra, A.; Berth-Jones, J.; Bjerke, J.; Christophers, E.; Knop, J.; Knulst, A. C.; Morren, M.; Morris, A.; Reitamo, S.; Roed-Petersen, J.; Schoepf, E.; Thestrup-Pedersen, K.; van der Valk, P. G.; Bos, J. D.

    2001-01-01

    SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. This study was designed to determine the safety and efficacy

  7. SDZ ASM 981: an emerging safe and effective treatment for atopic dermatitis

    NARCIS (Netherlands)

    Luger, T; Van Leent, EJM; Graeber, M; Hedgecock, S; Thurston, M; Kandra, A; Berth-Jones, J; Bjerke, J; Christophers, E; Knulst, AC; Morren, M; Morris, A; Reitamo, S; Roed-Petersen, J; Schoepf, E; Thestrup-Pedersen, K; van der Valk, P. G. M.; Bos, JD

    Background SDZ ASM 981 is a selective inhibitor of the production of pro-inflammatory cytokines from T cells and mast cells in vitro. It is the first ascomycin macrolactam derivative under development for the treatment of inflammatory skin diseases. Objectives This study was: designed to determine

  8. Simulation and optimization of a coking wastewater biological treatment process by activated sludge models (ASM).

    Science.gov (United States)

    Wu, Xiaohui; Yang, Yang; Wu, Gaoming; Mao, Juan; Zhou, Tao

    2016-01-01

    Applications of activated sludge models (ASM) in simulating industrial biological wastewater treatment plants (WWTPs) are still difficult due to refractory and complex components in influents as well as diversity in activated sludges. In this study, an ASM3 modeling study was conducted to simulate and optimize a practical coking wastewater treatment plant (CWTP). First, respirometric characterizations of the coking wastewater and CWTP biomasses were conducted to determine the specific kinetic and stoichiometric model parameters for the consecutive aeration-anoxic-aeration (O-A/O) biological process. All ASM3 parameters have been further estimated and calibrated, through cross validation by the model dynamic simulation procedure. Consequently, an ASM3 model was successfully established to accurately simulate the CWTP performances in removing COD and NH4-N. An optimized CWTP operation condition could be proposed reducing the operation cost from 6.2 to 5.5 €/m(3) wastewater. This study is expected to provide a useful reference for mathematic simulations of practical industrial WWTPs. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Technical report on comparative analysis of ASME QA requirements and ISO series

    International Nuclear Information System (INIS)

    Kim, Kwan Hyun

    2000-06-01

    This technical report provides the differences on the QA requirement ASME and ISO in nuclear fields. This report applies to the quality assurance(QA) programmes of the design of two requirement. The organization having overall responsibility for the nuclear design, preservation, fabrication shall be described in this report in each stage of design project

  10. ASM LabCap’s contributions to disease surveillance and the International Health Regulations (2005

    Directory of Open Access Journals (Sweden)

    Hakiruwizera Celestin

    2010-12-01

    Full Text Available Abstract The revised International Health Regulations [IHR(2005], which requires the Member States of the World Health Organization (WHO to develop core capacities to detect, assess, report, and respond to public health threats, is bringing new challenges for national and international surveillance systems. As more countries move toward implementation and/or strengthening of their infectious disease surveillance programs, the strengthening of clinical microbiology laboratories becomes increasingly important because they serve as the first line responders to detect new and emerging microbial threats, re-emerging infectious diseases, the spread of antibiotic resistance, and the possibility of bioterrorism. In fact, IHR(2005 Core Capacity #8, “Laboratory”, requires that laboratory services be a part of every phase of alert and response. Public health laboratories in many resource-constrained countries require financial and technical assistance to build their capacity. In recognition of this, in 2006, the American Society for Microbiology (ASM established an International Laboratory Capacity Building Program, LabCap, housed under the ASM International Board. ASM LabCap utilizes ASM’s vast resources and its membership’s expertise—40,000 microbiologists worldwide—to strengthen clinical and public health laboratory systems in low and low-middle income countries. ASM LabCap’s program activities align with HR(2005 by building the capability of resource-constrained countries to develop quality-assured, laboratory-based information which is critical to disease surveillance and the rapid detection of disease outbreaks, whether they stem from natural, deliberate or accidental causes. ASM LabCap helps build laboratory capacity under a cooperative agreement with the U.S. Centers for Disease Control and Prevention (CDC and under a sub-contract with the Program for Appropriate Technology in Health (PATH funded by the United States Agency for

  11. Statistical analysis of geomagnetic field intensity differences between ASM and VFM instruments onboard Swarm constellation

    Science.gov (United States)

    De Michelis, Paola; Tozzi, Roberta; Consolini, Giuseppe

    2017-02-01

    From the very first measurements made by the magnetometers onboard Swarm satellites launched by European Space Agency (ESA) in late 2013, it emerged a discrepancy between scalar and vector measurements. An accurate analysis of this phenomenon brought to build an empirical model of the disturbance, highly correlated with the Sun incidence angle, and to correct vector data accordingly. The empirical model adopted by ESA results in a significant decrease in the amplitude of the disturbance affecting VFM measurements so greatly improving the vector magnetic data quality. This study is focused on the characterization of the difference between magnetic field intensity measured by the absolute scalar magnetometer (ASM) and that reconstructed using the vector field magnetometer (VFM) installed on Swarm constellation. Applying empirical mode decomposition method, we find the intrinsic mode functions (IMFs) associated with ASM-VFM total intensity differences obtained with data both uncorrected and corrected for the disturbance correlated with the Sun incidence angle. Surprisingly, no differences are found in the nature of the IMFs embedded in the analyzed signals, being these IMFs characterized by the same dominant periodicities before and after correction. The effect of correction manifests in the decrease in the energy associated with some IMFs contributing to corrected data. Some IMFs identified by analyzing the ASM-VFM intensity discrepancy are characterized by the same dominant periodicities of those obtained by analyzing the temperature fluctuations of the VFM electronic unit. Thus, the disturbance correlated with the Sun incidence angle could be still present in the corrected magnetic data. Furthermore, the ASM-VFM total intensity difference and the VFM electronic unit temperature display a maximal shared information with a time delay that depends on local time. Taken together, these findings may help to relate the features of the observed VFM-ASM total intensity

  12. Report on the FY17 Development of Computer Program for ASME Section III, Division 5, Subsection HB, Subpart B Rules

    Energy Technology Data Exchange (ETDEWEB)

    Swindeman, M. J. [Argonne National Lab. (ANL), Argonne, IL (United States); Jetter, R. I. [Argonne National Lab. (ANL), Argonne, IL (United States); Sham, T. -L. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2017-01-01

    One of the objectives of the high temperature design methodology activities is to develop and validate both improvements and the basic features of ASME Boiler and Pressure Vessel Code, Section III, Rules for Construction of Nuclear Facility Components, Division 5, High Temperature Reactors, Subsection HB, Subpart B (HBB). The overall scope of this task is to develop a computer program to aid assessment procedures of components under specified loading conditions in accordance with the elevated temperature design requirements for Division 5 Class A components. There are many features and alternative paths of varying complexity in HBB. The initial focus of this computer program is a basic path through the various options for a single reference material, 316H stainless steel. However, the computer program is being structured for eventual incorporation all of the features and permitted materials of HBB. This report will first provide a description of the overall computer program, particular challenges in developing numerical procedures for the assessment, and an overall approach to computer program development. This is followed by a more comprehensive appendix, which is the draft computer program manual for the program development. The strain limits rules have been implemented in the computer program. The evaluation of creep-fatigue damage will be implemented in future work scope.

  13. Application of nuclear air cleaning and treatment codes

    Energy Technology Data Exchange (ETDEWEB)

    Kriskovich, J.R. [Westinghouse Hanford Company, Richland, WA (United States)

    1995-02-01

    All modifications to existing ventilation systems, as well as any new ventilation systems used on the Hanford Site are required to meet both American Society of Mechanical Engineers (ASME) codes N509 and N510. Difficulties encountered when applying code N509 at the Hanford Site include the composition of the ventilation air stream and requirements related to ventilation equipment procurement. Also, the existing ventilation systems for the waste tanks at the Hanford Site cannot be tested in accordance with code N510 because of the current configuration of these systems.

  14. 78 FR 37885 - Approval of American Society of Mechanical Engineers' Code Cases

    Science.gov (United States)

    2013-06-24

    ... Approval of American Society of Mechanical Engineers' Code Cases; Proposed Rule #0;#0;Federal Register... COMMISSION 10 CFR Part 50 [NRC-2009-0359] RIN 3150-AI72 Approval of American Society of Mechanical Engineers... Society of Mechanical Engineers (ASME). This proposed action would allow nuclear power plant licensees...

  15. Parametric study of emerging high power accelerator applications using Accelerator Systems Model (ASM)

    International Nuclear Information System (INIS)

    Berwald, D.H.; Mendelsohn, S.S.; Myers, T.J.; Paulson, C.C.; Peacock, M.A.; Piaszczyk, CM.; Rathke, J.W.; Piechowiak, E.M.

    1996-01-01

    Emerging applications for high power rf linacs include fusion materials testing, generation of intense spallation neutrons for neutron physics and materials studies, production of nuclear materials and destruction of nuclear waste. Each requires the selection of an optimal configuration and operating parameters for its accelerator, rf power system and other supporting subsystems. Because of the high cost associated with these facilities, economic considerations become paramount, dictating a full evaluation of the electrical and rf performance, system reliability/availability, and capital, operating, and life cycle costs. The Accelerator Systems Model (ASM), expanded and modified by Northrop Grumman during 1993-96, provides a unique capability for detailed layout and evaluation of a wide variety of normal and superconducting accelerator and rf power configurations. This paper will discuss the current capabilities of ASM, including the available models and data base, and types of trade studies that can be performed for the above applications. (author)

  16. Design and test of ASME strainer for primary cooling system in HANARO

    International Nuclear Information System (INIS)

    Park, Yong-Chul; Ryu, Jeong-Soo

    1999-01-01

    The ASME strainers have been newly installed at the suction side of each reactor coolant pump to get rid of the foreign materials which may damage the pump impeller or interfere with the coolant path of fuel flow tube or primary plate type heat exchanger. The strainer was designed in accordance with ASME SEC. III, DIV. 1, ND and the structural integrity was verified by seismic analysis. The screen was designed in accordance with the effective void area from the result of flow analysis for T-type strainer. After installation of the strainer, it was confirmed through the field test that the flow characteristics of primary cooling system were not adversely affected. The pressure loss coefficient was calculated by Darcy equation using the pressure difference through each strainer and the flow rate measured during the strainer performance test. And these are useful data to predict flow variations by the pressure difference. (author)

  17. Extended activated sludge model no. 1 (ASM1 for simulating biodegradation process using bacterial technology

    Directory of Open Access Journals (Sweden)

    Ya-jing Song

    2012-09-01

    Full Text Available Phosphorus is one of the most important nutrients required to support various kinds of biodegradation processes. As this particular nutrient is not included in the activated sludge model no. 1 (ASM1, this study extended this model in order to determine the fate of phosphorus during the biodegradation processes. When some of the kinetics parameters are modified using observed data from the restoration project of the Xuxi River in Wuxi City, China, from August 25 to 31 in 2009, the extended model shows excellent results. In order to obtain optimum values of coefficients of nitrogen and phosphorus, the mass fraction method was used to ensure that the final results were reasonable and practically relevant. The temporal distribution of the data calculated with the extended ASM1 approximates that of the observed data.

  18. The control of safety allowance for nuclear power plant components in ASME-BPVC

    International Nuclear Information System (INIS)

    Yao Weida; Ning Dong; Yang Ren'an; He Yinbiao; Xie Yongcheng; Zhang Ming; Yao Yangui

    2011-01-01

    How to control the 'safety allowance' reasonably at each phase of materials, design, fabrication, test, examination, building, pre-service and in-service operation and others in ASME-BPVC was preliminarily discussed. The two quantitative requirements of 'safety factor' and 'acceptance criteria' were dissected. The responsibilities of controlled documents and personnel to assure 'safety allowance' were also represented. (authors)

  19. Meeting report on the ASM Conference on Mechanisms of Interbacterial Cooperation and Competition.

    Science.gov (United States)

    Lories, Bram; Parijs, Ilse; Foster, Kevin R; Steenackers, Hans P

    2017-08-14

    The ASM Conference on Mechanisms of Interbacterial Cooperation and Competition was held in Washington DC, from 1 to 4 March 2017. The conference provided an international forum for sociomicrobiologists from different disciplines to present and discuss new findings. The meeting covered a wide range of topics, spanning molecular mechanisms, ecology, evolution, computation and manipulation of interbacterial interactions, and encompassed social communities in medicine, the natural environment, and industry. This report summarizes the presentations and emerging themes. Copyright © 2017 American Society for Microbiology.

  20. RXTE ASM Observations of GRB991216 - A One Hour Old X-ray Afterglow

    Science.gov (United States)

    Corbet, R.; Smith, D. A.

    The Gamma-ray Burst 991216 (the ``Beethoven" burst) was both very bright itself and also had an unusually bright X-ray afterglow. This afterglow was observed and localized by the RXTE PCA 4 hours after the burst occurred (Takeshima et al. 1999). This position determination then enabled an optical afterglow to be found (Uglesich et al 1999). Serendipitously, the RXTE ASM obtained a sequence of 7 observations covering this source in a period of 11 minutes starting just 1 hour after the burst peak. From these 7 dwells, a flux of 32 +/- 8 mCrabs (1 sigma error) was determined which is consistent with a power-law extrapolation of RXTE PCA flux measurements. While GRB afterglows are generally faint and thus difficult for the RXTE ASM to study, due to its modest collecting area and short observation times, we believe that this unusually bright afterglow has indeed been detected. These results indicate that the RXTE ASM has provided a measurement of an X-ray afterglow light curve at times which have previously not been studied.

  1. Linearization of the activated sludge model ASM1 for fast and reliable predictions.

    Science.gov (United States)

    Smets, Ilse Y; Haegebaert, Jeroen V; Carrette, Ronald; Van Impe, Jan F

    2003-04-01

    In this paper a strategy is proposed to reduce the complexity of the activated sludge model no. 1 (ASM1) which describes the biotransformation processes in a common activated sludge process with N-removal. The key feature of the obtained reduced model is that it combines high predictive value (all state variables keep their biological interpretation) with very low computation time. Therefore, this model is a valuable tool in a risk assessment environment (designed for the evaluation of wastewater treatment plants facing stricter effluent norms) as well as in on-line (MPC) control strategies. The complexity reduction procedure consists of four steps. In the first step representative input/output data sets are generated by simulating the full ASM1 model. In the second step the ASM1 model is rewritten in state space format with linear approximations of the nonlinear (kinetic) terms. In the third step the unknown parameters in the linear terms are identified based on the generated input/output data. To reduce the amount of parameter sets that have to be identified (to cover the full operation range of the plant), a Multi-Model interpolation procedure is introduced as a last step.

  2. Comparison of SKIFS 2004:1 and Tillsynshandbok PSA against the ASME PRA Standard and European requirements on PSA; Jaemfoerelse av SKIFS 2004:1 och Tillsynshandbok PSA mot ASME PRA Standard och Europeiska krav paa PSA

    Energy Technology Data Exchange (ETDEWEB)

    Hellstroem, Per

    2005-04-15

    Requirements on PSA for risk informed applications are expressed in different international documents. The ASME PRA standard published in spring 2002 is one such document, PSA requirements are also expressed in the European Utility Requirements (EUR) for new reactors. The Swedish PSA requirements are provided in the Swedish regulators (SKI) statutes SKIFS 2004:1. SKI also has a review handbook for PSA activities (SKI report 2003:48). The review handbook is a support during review of the utilities PSA activities and the PSAs themselves. The review handbook expresses SKIs expectations by providing so called important aspects for both the PSA work and the PSAs, A comparison of SKIFS requirements and the important aspects in the Review handbook, on one side, and the requirements on PSA in EUR and ASME on the other side, is presented. The comparison shows a large difference in the level of detail in the different documents, where ASME is most detailed and specific. This is expected since the SKI review handbook not is a 'PSA guide' in the same way as the ASME PRA standard. A direct comparison of the ASME PRA standard requirements with the important aspects in the review handbook cannot answer the question which ASME capacity level that is achieved by a PSA meeting all important aspects. The conclusion is that it is not likely to achieve capacity level 2 and 3, since very few ASME level 3 attributes are explicitly expressed as important aspects, though many are expressed in general terms. The review handbook important aspects that are most similar to the ASME capacity level 1 attributes are initiating events, sequence analysis, and system analysis while less similarity is found for analysis of operator actions data analysis, quantification and containment analysis (level 2). Less similarity is found for capacity level 2 and 3. However, the number of additional ASME attributes on capacity level 2 and 3 are few. There are also important aspects in the review

  3. GC-ASM: Synergistic Integration of Graph-Cut and Active Shape Model Strategies for Medical Image Segmentation.

    Science.gov (United States)

    Chen, Xinjian; Udupa, Jayaram K; Alavi, Abass; Torigian, Drew A

    2013-05-01

    Image segmentation methods may be classified into two categories: purely image based and model based. Each of these two classes has its own advantages and disadvantages. In this paper, we propose a novel synergistic combination of the image based graph-cut (GC) method with the model based ASM method to arrive at the GC-ASM method for medical image segmentation. A multi-object GC cost function is proposed which effectively integrates the ASM shape information into the GC framework. The proposed method consists of two phases: model building and segmentation. In the model building phase, the ASM model is built and the parameters of the GC are estimated. The segmentation phase consists of two main steps: initialization (recognition) and delineation. For initialization, an automatic method is proposed which estimates the pose (translation, orientation, and scale) of the model, and obtains a rough segmentation result which also provides the shape information for the GC method. For delineation, an iterative GC-ASM algorithm is proposed which performs finer delineation based on the initialization results. The proposed methods are implemented to operate on 2D images and evaluated on clinical chest CT, abdominal CT, and foot MRI data sets. The results show the following: (a) An overall delineation accuracy of TPVF > 96%, FPVF segmentation step compared to GC which requires seed specification and improves on the accuracy of GC. (e) One disadvantage of GC-ASM is its increased computational expense owing to the iterative nature of the algorithm.

  4. Densidade Mineral Óssea em Mulheres Asmáticas, na Fase Perimenopausa

    Directory of Open Access Journals (Sweden)

    Anne K. Laatikainen

    1999-07-01

    Full Text Available RESUMO: Os corticóides inalados, constituem a terapêutica anti-inflamatória de eleição, utilizada nos asmáticos, por longos penodos.Para além dos corticóides inalados utilizados como terapêutica preventiva, a corticoterapia oral e endovenosa é por vezes necessária nos períodos de exacerbação da doença.É bem conhecido o risco de osteoporose em doentes com asma grave medicados com corticoterapta oral a longo prazo O efeito dos corticóides inalados a nivel da densidade óssea, não é bem conhecido, pelo que tem sido alvo de estudos recentes.A menopausa é considerada o principal factor de risco da osteoporose. Ainda não é bem conhecido qual o papel da asma como factor de risco de ostcoporose equal o impacto dos corticóides inalados na densitometria óssea.Os autores procederam a urn estudo inicialmente dingido a uma população de 14220 mulheres dos 47 aos 56 anos de idade (período perimenopausa, residentes na Província de Kuopio, no Leste da Finlândia.Foi enviado urn inquérito incluindo a história ginecológica, uso de terapêutica hormonal de substituição, paridade, peso, altura, actividade fisica, consumo de produtos lácteos, hábitos tabágicos, morbilidade e teraêuticas habituais. Houve resposta em 84 4% dos inquiridos.Foi realizada osteodensitometria óssea (BMD do colo do fémur esquerdo e coluna em 3222 mulheres, de acordo com um estudo randomizado simples, estratificado.Após exclusão de alguns registos considerados inválidos, a população estudada consistia em 2941 mulheres, das quais 119 eram asmáticas. A estas foi feito um inquérito adicional acerca do uso de cortticóides, dose diária, duração e regularidade.Os autores verificaram que 72 doentes (60.5% estavam medicadas com corticóides inalados. Dez asmáticas faziam regularmente corticoterapia oral. Em 61 doentes havia referência a pelo menos um curso de corticóide oral nos últimos 6 meses. Vinte e oito asmáticas nunca tinham feito terap

  5. Understanding the Long-Term Spectral Variability of Cygnus X-1 from BATSE and ASM Observations

    Science.gov (United States)

    Zdziarski, Andrzej A.; Poutanen, Juri; Paciesas, William S.; Wen, Linqing; Six, N. Frank (Technical Monitor)

    2002-01-01

    We present a spectral analysis of observations of Cygnus X-1 by the RXTE/ASM (1.5-12 keV) and CGRO/BATSE (20-300 keV), including about 1200 days of simultaneous data. We find a number of correlations between intensities and hardnesses in different energy bands from 1.5 keV to 300 keV. In the hard (low) spectral state, there is a negative correlation between the ASM 1.5-12 keV flux and the hardness at any energy. In the soft (high) spectral state, the ASM flux is positively correlated with the ASM hardness (as previously reported) but uncorrelated with the BATSE hardness. In both spectral states, the BATSE hardness correlates with the flux above 100 keV, while it shows no correlation with the flux in the 20-100 keV range. At the same time, there is clear correlation between the BATSE fluxes below and above 100 keV. In the hard state, most of the variability can be explained by softening the overall spectrum with a pivot at approximately 50 keV. The observations show that there has to be another, independent variability pattern of lower amplitude where the spectral shape does not change when the luminosity changes. In the soft state, the variability is mostly caused by a variable hard (Comptonized) spectral component of a constant shape superimposed on a constant soft blackbody component. These variability patterns are in agreement with the dependence of the rms variability on the photon energy in the two states. We interpret the observed correlations in terms of theoretical Comptonization models. In the hard state, the variability appears to be driven mostly by changing flux in seed photons Comptonized in a hot thermal plasma cloud with an approximately constant power supply. In the soft state, the variability is consistent with flares of hybrid, thermal/nonthermal, plasma with variable power above a stable cold disk. Also, based on broadband pointed observations simultaneous with those of the ASM and BATSE, we find the intrinsic bolometric luminosity increases by a

  6. PIPE STRESS and VERPIP codes for stress analysis and verifications of PEC reactor piping

    International Nuclear Information System (INIS)

    Cesari, F.; Ferranti, P.; Gasparrini, M.; Labanti, L.

    1975-01-01

    To design LMFBR piping systems following ASME Sct. III requirements unusual flexibility computer codes are to be adopted to consider piping and its guard-tube. For this purpose PIPE STRESS code previously prepared by Southern-Service, has been modified. Some subroutine for detailed stress analysis and principal stress calculations on all the sections of piping have been written and fitted in the code. Plotter can also be used. VERPIP code for automatic verifications of piping as class 1 Sct. III prescriptions has been also prepared. The results of PIPE STRESS and VERPIP codes application to PEC piping are in section III of this report

  7. ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

    Directory of Open Access Journals (Sweden)

    Yongsoon Kim

    Full Text Available In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

  8. ASM-3 Acid Sphingomyelinase Functions as a Positive Regulator of the DAF-2/AGE-1 Signaling Pathway and Serves as a Novel Anti-Aging Target

    Science.gov (United States)

    Kim, Yongsoon; Sun, Hong

    2012-01-01

    In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals. PMID:23049887

  9. ASM-3 acid sphingomyelinase functions as a positive regulator of the DAF-2/AGE-1 signaling pathway and serves as a novel anti-aging target.

    Science.gov (United States)

    Kim, Yongsoon; Sun, Hong

    2012-01-01

    In C. elegans, the highly conserved DAF-2/insulin/insulin-like growth factor 1 receptor signaling (IIS) pathway regulates longevity, metabolism, reproduction and development. In mammals, acid sphingomyelinase (ASM) is an enzyme that hydrolyzes sphingomyelin to produce ceramide. ASM has been implicated in CD95 death receptor signaling under certain stress conditions. However, the involvement of ASM in growth factor receptor signaling under physiological conditions is not known. Here, we report that in vivo ASM functions as a positive regulator of the DAF-2/IIS pathway in C. elegans. We have shown that inactivation of asm-3 extends animal lifespan and promotes dauer arrest, an alternative developmental process. A significant cooperative effect on lifespan is observed between asm-3 deficiency and loss-of-function alleles of the age-1/PI 3-kinase, with the asm-3; age-1 double mutant animals having a mean lifespan 259% greater than that of the wild-type animals. The lifespan extension phenotypes caused by the loss of asm-3 are dependent on the functions of daf-16/FOXO and daf-18/PTEN. We have demonstrated that inactivation of asm-3 causes nuclear translocation of DAF-16::GFP protein, up-regulates endogenous DAF-16 protein levels and activates the downstream targeting genes of DAF-16. Together, our findings reveal a novel role of asm-3 in regulation of lifespan and diapause by modulating IIS pathway. Importantly, we have found that two drugs known to inhibit mammalian ASM activities, desipramine and clomipramine, markedly extend the lifespan of wild-type animals, in a manner similar to that achieved by genetic inactivation of the asm genes. Our studies illustrate a novel strategy of anti-aging by targeting ASM, which may potentially be extended to mammals.

  10. Bronchodilatory and anti-inflammatory effects of ASM-024, a nicotinic receptor ligand, developed for the treatment of asthma.

    Directory of Open Access Journals (Sweden)

    Evelyne Israël Assayag

    Full Text Available Conventional asthma and COPD treatments include the use of bronchodilators, mainly β2-adrenergic agonists, muscarinic receptor antagonists and corticosteroids or leukotriene antagonists as anti-inflammatory agents. These active drugs are administered either separately or given as a fixed-dose combination medication into a single inhaler. ASM-024, a homopiperazinium compound, derived from the structural modification of diphenylmethylpiperazinium (DMPP, has been developed to offer an alternative mechanism of action that could provide symptomatic control through combined anti-inflammatory and bronchodilator properties in a single entity. A dose-dependent inhibition of cellular inflammation in bronchoalveolar lavage fluid was observed in ovalbumin-sensitized mice, subsequently treated for 3 days by nose-only exposure with aerosolized ASM-024 at doses up to 3.8 mg/kg (ED50 = 0.03 mg/kg. The methacholine ED250 values indicated that airway hyperresponsivenness (AHR to methacholine decreased following ASM-024 administration by inhalation at a dose of 1.5 mg/kg, with a value of 0.145 ± 0.032 mg/kg for ASM 024-treated group as compared to 0.088 ± 0.023 mg/kg for untreated mice. In in vitro isometric studies, ASM-024 elicited dose-dependent relaxation of isolated mouse tracheal, human, and dog bronchial preparations contracted with methacholine and guinea pig tracheas contracted with histamine. ASM-024 showed also a dose and time dependant protective effect on methacholine-induced contraction. Overall, with its combined anti-inflammatory, bronchodilating and bronchoprotective properties, ASM-024 may represent a new class of drugs with a novel pharmacological approach that could prove useful for the chronic maintenance treatment of asthma and, possibly, COPD.

  11. Neurospora crassa ASM-1 complements the conidiation defect in a stuA mutant of Aspergillus nidulans.

    Science.gov (United States)

    Chung, Dawoon; Upadhyay, Srijana; Bomer, Brigitte; Wilkinson, Heather H; Ebbole, Daniel J; Shaw, Brian D

    2015-01-01

    Aspergillus nidulans StuA and Neurospora crassa ASM-1 are orthologous APSES (ASM-1, PHD1, SOK2, Efg1, StuA) transcription factors conserved across a diverse group of fungi. StuA and ASM-1 have roles in asexual (conidiation) and sexual (ascospore formation) development in both organisms. To address the hypothesis that the last common ancestor of these diverse fungi regulated conidiation with similar genes, asm-1 was introduced into the stuA1 mutant of A. nidulans. Expression of asm-1 complemented defective conidiophore morphology and restored conidia production to wild type levels in stuA1. Expression of asm-1 in the stuA1 strain did not rescue the defect in sexual development. When the conidiation regulator AbaA was tagged at its C-terminus with GFP in A. nidulans, it localized to nuclei in phialides. When expressed in the stuA1 mutant, AbaA::GFP localized to nuclei in conidiophores but no longer was confined to phialides, suggesting that expression of AbaA in specific cell types of the conidiophore was conditioned by StuA. Our data suggest that the function in conidiation of StuA and ASM-1 is conserved and support the view that, despite the great morphological and ontogenic diversity of their condiphores, the last common ancestor of A. nidulans and N. crassa produced an ortholog of StuA that was involved in conidiophore development. © 2015 by The Mycological Society of America.

  12. Bronchodilatory and anti-inflammatory effects of ASM-024, a nicotinic receptor ligand, developed for the treatment of asthma.

    Science.gov (United States)

    Assayag, Evelyne Israël; Beaulieu, Marie-Josée; Cormier, Yvon

    2014-01-01

    Conventional asthma and COPD treatments include the use of bronchodilators, mainly β2-adrenergic agonists, muscarinic receptor antagonists and corticosteroids or leukotriene antagonists as anti-inflammatory agents. These active drugs are administered either separately or given as a fixed-dose combination medication into a single inhaler. ASM-024, a homopiperazinium compound, derived from the structural modification of diphenylmethylpiperazinium (DMPP), has been developed to offer an alternative mechanism of action that could provide symptomatic control through combined anti-inflammatory and bronchodilator properties in a single entity. A dose-dependent inhibition of cellular inflammation in bronchoalveolar lavage fluid was observed in ovalbumin-sensitized mice, subsequently treated for 3 days by nose-only exposure with aerosolized ASM-024 at doses up to 3.8 mg/kg (ED50 = 0.03 mg/kg). The methacholine ED250 values indicated that airway hyperresponsivenness (AHR) to methacholine decreased following ASM-024 administration by inhalation at a dose of 1.5 mg/kg, with a value of 0.145 ± 0.032 mg/kg for ASM 024-treated group as compared to 0.088 ± 0.023 mg/kg for untreated mice. In in vitro isometric studies, ASM-024 elicited dose-dependent relaxation of isolated mouse tracheal, human, and dog bronchial preparations contracted with methacholine and guinea pig tracheas contracted with histamine. ASM-024 showed also a dose and time dependant protective effect on methacholine-induced contraction. Overall, with its combined anti-inflammatory, bronchodilating and bronchoprotective properties, ASM-024 may represent a new class of drugs with a novel pharmacological approach that could prove useful for the chronic maintenance treatment of asthma and, possibly, COPD.

  13. The ASM-NSF Biology Scholars Program: An Evidence-Based Model for Faculty Development

    Directory of Open Access Journals (Sweden)

    Amy L. Chang

    2016-05-01

    Full Text Available The American Society for Microbiology (ASM established its ASM-NSF (National Science Foundation Biology Scholars Program (BSP to promote undergraduate education reform by 1 supporting biologists to implement evidence-based teaching practices, 2 engaging life science professional societies to facilitate biologists’ leadership in scholarly teaching within the discipline, and 3 participating in a teaching community that fosters disciplinary-level science, technology, engineering, and mathematics (STEM reform. Since 2005, the program has utilized year-long residency training to provide a continuum of learning and practice centered on principles from the scholarship of teaching and learning (SoTL to more than 270 participants (“scholars” from biology and multiple other disciplines. Additionally, the program has recruited 11 life science professional societies to support faculty development in SoTL and discipline-based education research (DBER. To identify the BSP’s long-term outcomes and impacts, ASM engaged an external evaluator to conduct a study of the program’s 2010­–2014 scholars (n = 127 and society partners. The study methods included online surveys, focus groups, participant observation, and analysis of various documents. Study participants indicate that the program achieved its proposed goals relative to scholarship, professional society impact, leadership, community, and faculty professional development. Although participants also identified barriers that hindered elements of their BSP participation, findings suggest that the program was essential to their development as faculty and provides evidence of the BSP as a model for other societies seeking to advance undergraduate science education reform. The BSP is the longest-standing faculty development program sponsored by a collective group of life science societies. This collaboration promotes success across a fragmented system of more than 80 societies representing the life

  14. The ASM-NSF Biology Scholars Program: An Evidence-Based Model for Faculty Development.

    Science.gov (United States)

    Chang, Amy L; Pribbenow, Christine M

    2016-05-01

    The American Society for Microbiology (ASM) established its ASM-NSF (National Science Foundation) Biology Scholars Program (BSP) to promote undergraduate education reform by 1) supporting biologists to implement evidence-based teaching practices, 2) engaging life science professional societies to facilitate biologists' leadership in scholarly teaching within the discipline, and 3) participating in a teaching community that fosters disciplinary-level science, technology, engineering, and mathematics (STEM) reform. Since 2005, the program has utilized year-long residency training to provide a continuum of learning and practice centered on principles from the scholarship of teaching and learning (SoTL) to more than 270 participants ("scholars") from biology and multiple other disciplines. Additionally, the program has recruited 11 life science professional societies to support faculty development in SoTL and discipline-based education research (DBER). To identify the BSP's long-term outcomes and impacts, ASM engaged an external evaluator to conduct a study of the program's 2010-2014 scholars (n = 127) and society partners. The study methods included online surveys, focus groups, participant observation, and analysis of various documents. Study participants indicate that the program achieved its proposed goals relative to scholarship, professional society impact, leadership, community, and faculty professional development. Although participants also identified barriers that hindered elements of their BSP participation, findings suggest that the program was essential to their development as faculty and provides evidence of the BSP as a model for other societies seeking to advance undergraduate science education reform. The BSP is the longest-standing faculty development program sponsored by a collective group of life science societies. This collaboration promotes success across a fragmented system of more than 80 societies representing the life sciences and helps

  15. ASME N510 test results for Savannah River Site AACS filter compartments

    Energy Technology Data Exchange (ETDEWEB)

    Paul, J.D.; Punch, T.M. [Westinghouse Savannah River Company, Aiken, SC (United States)

    1995-02-01

    The K-Reactor at the Savannah River Site recently implemented design improvements for the Airborne Activity Confinement System (AACS) by procuring, installing, and testing new Air Cleaning Units, or filter compartments, to ASME AG-11, N509, and N510 requirements. Specifically, these new units provide documentable seismic resistance to a Design Basis Accident earthquake, provide 2 inch adsorber beds with 0.25 second residence time, and meet all AG-1, N509, and N510 requirements for testability and maintainability. This paper presents the results of the Site acceptance testing and discusses an issue associated with sample manifold qualification testing.

  16. Radiografia Torácica em Crise Asmática

    OpenAIRE

    Sanches, Marcos; Marques, Patricia; Oliveira, Elisabete; Lopes, Aldina Canteiro

    2013-01-01

    Criança de oito anos, asmática que iniciou de forma súbita opressão torácica, disfagia e cansaço, motivo pelo qual recorreu ao serviço de urgência. Ao exame físico apresentava tiragem intercostal, polipneia e edema supraclavicular à direita crepitante. A auscultação pulmonar revelava murmúrio vesicular diminuído bilateralmente, aumento do tempo expiratório com sibilos dispersos. A radiografia (Rx) de tórax demonstrou sinais de pneumomediastino (figura 1), pelo que iniciou repouso e tratamento...

  17. Batse/Sax and Batse/RXTE-ASM Joint Spectral Studies of GRBs

    Science.gov (United States)

    Paciesas, William S.

    2002-01-01

    We proposed to make joint spectral analysis of gamma-ray bursts (GRBs) in the BATSE data base that are located within the fields of view of either the BeppoSAX wide field cameras (WFCs) or the RXTE all-sky monitor (ASM). The very broad-band coverage obtained in this way would facilitate various studies of GRB spectra that are difficult to perform with BATSE data alone. Unfortunately, the termination of the CGRO mission in June 2000 was not anticipated at the time of the proposal, and the sample of common events turned out to be smaller than we would have liked.

  18. Robust boundary detection of left ventricles on ultrasound images using ASM-level set method.

    Science.gov (United States)

    Zhang, Yaonan; Gao, Yuan; Li, Hong; Teng, Yueyang; Kang, Yan

    2015-01-01

    Level set method has been widely used in medical image analysis, but it has difficulties when being used in the segmentation of left ventricular (LV) boundaries on echocardiography images because the boundaries are not very distinguish, and the signal-to-noise ratio of echocardiography images is not very high. In this paper, we introduce the Active Shape Model (ASM) into the traditional level set method to enforce shape constraints. It improves the accuracy of boundary detection and makes the evolution more efficient. The experiments conducted on the real cardiac ultrasound image sequences show a positive and promising result.

  19. Coding Partitions

    Directory of Open Access Journals (Sweden)

    Fabio Burderi

    2007-05-01

    Full Text Available Motivated by the study of decipherability conditions for codes weaker than Unique Decipherability (UD, we introduce the notion of coding partition. Such a notion generalizes that of UD code and, for codes that are not UD, allows to recover the ``unique decipherability" at the level of the classes of the partition. By tacking into account the natural order between the partitions, we define the characteristic partition of a code X as the finest coding partition of X. This leads to introduce the canonical decomposition of a code in at most one unambiguouscomponent and other (if any totally ambiguouscomponents. In the case the code is finite, we give an algorithm for computing its canonical partition. This, in particular, allows to decide whether a given partition of a finite code X is a coding partition. This last problem is then approached in the case the code is a rational set. We prove its decidability under the hypothesis that the partition contains a finite number of classes and each class is a rational set. Moreover we conjecture that the canonical partition satisfies such a hypothesis. Finally we consider also some relationships between coding partitions and varieties of codes.

  20. Performance Demonstration Initiative U.S. implementation of ASME B and PV code section 11 Appendix 8

    International Nuclear Information System (INIS)

    Becker, F.L.; Ammirato, F.; Huffman, K.

    1994-01-01

    New requirements have now been added to Section 11 as mandatory Appendix 8, ''Performance Demonstration Requirements for Ultrasonic Examination systems''. The appendix was recently published and incorporates performance demonstration requirements for ultrasonic examination equipment, procedures, and personnel. These new requirements will have far reaching and significant impact on the conduct of ISI at all nuclear power plants. For the first time since Section 11 was issued in 1970, the effectiveness of ultrasonic examination procedures and the proficiency of examiners must be demonstrated on reactor pressure vessel (RPV), piping, and bolting markups containing real flaws, Recognizing the importance and complexity of Appendix 8 implementation, representatives from all US nuclear utilities have formed the Performance Demonstration Initiative (PDI) to implement Appendix 8 to provide for uniform implementation

  1. Coding Class

    DEFF Research Database (Denmark)

    Ejsing-Duun, Stine; Hansbøl, Mikala

    Sammenfatning af de mest væsentlige pointer fra hovedrapporten: Dokumentation og evaluering af Coding Class......Sammenfatning af de mest væsentlige pointer fra hovedrapporten: Dokumentation og evaluering af Coding Class...

  2. Broncoespasmo induzido pelo exercício em adolescentes asmáticos obesos e não-obesos

    OpenAIRE

    Lopes,Wendell Arthur; Rosário,Nelson; Leite,Neiva

    2010-01-01

    OBJETIVO: Avaliar e comparar a frequência e intensidade do broncoespasmo induzido pelo exercício (BIE) em adolescentes asmáticos obesos e não-obesos. MÉTODOS: Estudo transversal e descritivo realizado com 39 adolescentes de ambos os sexos, com idade entre dez e 16 anos, divididos em dois grupos conforme o histórico clínico de asma e/ou rinite alérgica e o índice de massa corporal: asmáticos obesos (n=18); asmáticos não-obesos (n=21). Utilizou-se o teste de broncoprovocação com exercício para ...

  3. When a Plant Resistance Inducer Leaves the Lab for the Field: Integrating ASM into Routine Apple Protection Practices.

    Science.gov (United States)

    Marolleau, Brice; Gaucher, Matthieu; Heintz, Christelle; Degrave, Alexandre; Warneys, Romain; Orain, Gilles; Lemarquand, Arnaud; Brisset, Marie-Noëlle

    2017-01-01

    Plant resistance inducers, also called elicitors, could be useful to reduce the use of pesticides. However, their performance in controlling diseases in the field remains unsatisfactory due to lack of specific knowledge of how they can integrate crop protection practices. In this work, we focused on apple crop and acibenzolar- S -methyl (ASM), a well-known SAR (systemic acquired resistance) inducer of numerous plant species. We provide a protocol for orchard-effective control of apple scab due to the ascomycete fungus Venturia inaequalis , by applying ASM in combination with a light integrated pest management program. Besides we pave the way for future optimization levers by demonstrating in controlled conditions (i) the high influence of apple genotypes, (ii) the ability of ASM to prime defenses in newly formed leaves, (iii) the positive effect of repeated elicitor applications, (iv) the additive effect of a thinning fruit agent.

  4. Modelling the biological performance of a side-stream membrane bioreactor using ASM1.

    Science.gov (United States)

    Tian, Ke-Jun; Liu, Xin-Ai; Jiang, Tao; Kennedy, M D; Schippers, J C; Vanrolleghem, P A

    2004-01-01

    Membrane bioreactors (MBRs) are attracting global interest but the mathematical modeling of the biological performance of MBRs remains very limited. This study focuses on the modelling of a side-stream MBR system using Activated Sludge Model No. 1 (ASM1), and comparing the results with the modelling of traditional activated sludge processes. ASM1 parameters relevant for the long-term biological behaviour in MBR systems were calibrated (i.e. Y(H) = 0.72gCOD/gCOD, Y(A) = 0.25gCOD/gN, b(H) = 0.25 d(-1), b(A) = 0.080 d(-1) and f(P) = 0.06), and generally agreed with the parameters in traditional activated sludge processes, with the exception that a higher autotrophic biomass decay rate was observed in the MBR. A sensitivity analysis for steady state operation and DO dynamics suggested that the biological performance of the MBR system (the sludge concentration, effluent quality and the DO dynamics) are very sensitive to the parameters(i.e. Y(H), Y(A), b(H), b(A), micro(maxH) and micro(maxA)), and influent wastewater components(X(I), S(S), X(S), S(NH)).

  5. ASM1 dynamic calibration and long-term validation for an intermittently aerated WWTP.

    Science.gov (United States)

    Marquot, A; Stricker, A E; Racault, Y

    2006-01-01

    Activated sludge models, and ASM1 in particular, are well recognised and useful mathematical representations of the macroscopic processes involved in the biological degradation of the pollution carried by wastewater. Nevertheless, the use of these models through simulation software requires a careful methodology for their calibration (determination of the model parameters' values) and the validation step (verification with an independent data set). This paper presents the methodology and the results of dynamic calibration and validation tasks as a prior work to a modelling project for defining a reference guideline destined to French designers and operators. To reach these goals, a biological nutrient removal (BNR) wastewater treatment plant (WWTP) with intermittent aeration was selected and monitored for 2 years. Two sets of calibrated parameters are given and discussed. The results of the long-term validation task are presented through a 2-month simulation with lots of operation changes. Finally, it is concluded that, even if calibrating ASM1 with a high degree of confidence with a single set of parameters was not possible, the results of the calibration are sufficient to obtain satisfactory results over long-term dynamic simulation. However, simulating long periods reveals specific calibration issues such as the variation of the nitrification capacity due to external events.

  6. Application of adjusted subpixel method (ASM) in HRCT measurements of the bronchi in bronchial asthma patients and healthy individuals.

    Science.gov (United States)

    Mincewicz, Grzegorz; Rumiński, Jacek; Krzykowski, Grzegorz

    2012-02-01

    Recently, we described a model system which included corrections of high-resolution computed tomography (HRCT) bronchial measurements based on the adjusted subpixel method (ASM). To verify the clinical application of ASM by comparing bronchial measurements obtained by means of the traditional eye-driven method, subpixel method alone and ASM in a group comprised of bronchial asthma patients and healthy individuals. The study included 30 bronchial asthma patients and the control group comprised of 20 volunteers with no symptoms of asthma. The lowest internal and external diameters of the bronchial cross-sections (ID and ED) and their derivative parameters were determined in HRCT scans using: (1) traditional eye-driven method, (2) subpixel technique, and (3) ASM. In the case of the eye-driven method, lower ID values along with lower bronchial lumen area and its percentage ratio to total bronchial area were basic parameters that differed between asthma patients and healthy controls. In the case of the subpixel method and ASM, both groups were not significantly different in terms of ID. Significant differences were observed in values of ED and total bronchial area with both parameters being significantly higher in asthma patients. Compared to ASM, the eye-driven method overstated the values of ID and ED by about 30% and 10% respectively, while understating bronchial wall thickness by about 18%. Results obtained in this study suggest that the traditional eye-driven method of HRCT-based measurement of bronchial tree components probably overstates the degree of bronchial patency in asthma patients. Copyright © 2011 Elsevier Ireland Ltd. All rights reserved.

  7. Low appendicular skeletal muscle mass (ASM) with limited mobility and poor health outcomes in middle-aged African Americans.

    Science.gov (United States)

    Malmstrom, Theodore K; Miller, Douglas K; Herning, Margaret M; Morley, John E

    2013-09-01

    Recent efforts to provide a consensus definition propose that sarcopenia be considered a clinical syndrome associated with the loss of both skeletal muscle mass and muscle function that occurs with aging. Validation of sarcopenia definitions that include both low muscle mass and poor muscle function is needed. In the population-based African American Health (AAH) study (N = 998 at baseline/wave 1), muscle mass and mobility were evaluated in a clinical testing center in a subsample of N = 319 persons (ages 52-68) at wave 4 (2004). Muscle mass was measured using dual energy x-ray absorptiometry and mobility by a 6-min walk test and 4-m gait walk test. Height corrected appendicular skeletal mass (ASM; 9.0 ± 1.5 in n = 124 males, 8.3 ± 2.2 in n = 195 females) was computed as total lean muscle mass in arms and legs (kilograms) divided by the square of height (meters). Cross-sectional and longitudinal (6-year) associations of low ASM (bottom 25 % AAH sample; ASM with limited mobility (4-m gait walk ≤1 m/s or 6-min walk ASM with limited mobility was associated with IADL difficulties (p = .008) and frailty (p = .040) but not with ADL difficulties or falls in cross-sectional analyses; and with ADL difficulties (p = .022), IADL difficulties (p = .006), frailty (p = .039), and mortality (p = .003) but not with falls in longitudinal analyses adjusted for age and gender. Low ASM alone was marginally associated with mortality (p = .085) but not with other outcomes in cross-sectional or longitudinal analyses. Low ASM with limited mobility is associated with poor health outcomes among late middle-aged African Americans.

  8. 3D automatic anatomy segmentation based on iterative graph-cut-ASM

    International Nuclear Information System (INIS)

    Chen, Xinjian; Bagci, Ulas

    2011-01-01

    Purpose: This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. Methods: The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al.[Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. Results: The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 deg. and 0.03, and over all foot bones are about 3.5709 mm, 0.35 deg. and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and

  9. 3D automatic anatomy segmentation based on iterative graph-cut-ASM.

    Science.gov (United States)

    Chen, Xinjian; Bagci, Ulas

    2011-08-01

    This paper studies the feasibility of developing an automatic anatomy segmentation (AAS) system in clinical radiology and demonstrates its operation on clinical 3D images. The AAS system, the authors are developing consists of two main parts: object recognition and object delineation. As for recognition, a hierarchical 3D scale-based multiobject method is used for the multiobject recognition task, which incorporates intensity weighted ball-scale (b-scale) information into the active shape model (ASM). For object delineation, an iterative graph-cut-ASM (IGCASM) algorithm is proposed, which effectively combines the rich statistical shape information embodied in ASM with the globally optimal delineation capability of the GC method. The presented IGCASM algorithm is a 3D generalization of the 2D GC-ASM method that they proposed previously in Chen et al. [Proc. SPIE, 7259, 72590C1-72590C-8 (2009)]. The proposed methods are tested on two datasets comprised of images obtained from 20 patients (10 male and 10 female) of clinical abdominal CT scans, and 11 foot magnetic resonance imaging (MRI) scans. The test is for four organs (liver, left and right kidneys, and spleen) segmentation, five foot bones (calcaneus, tibia, cuboid, talus, and navicular). The recognition and delineation accuracies were evaluated separately. The recognition accuracy was evaluated in terms of translation, rotation, and scale (size) error. The delineation accuracy was evaluated in terms of true and false positive volume fractions (TPVF, FPVF). The efficiency of the delineation method was also evaluated on an Intel Pentium IV PC with a 3.4 GHZ CPU machine. The recognition accuracies in terms of translation, rotation, and scale error over all organs are about 8 mm, 10 degrees and 0.03, and over all foot bones are about 3.5709 mm, 0.35 degrees and 0.025, respectively. The accuracy of delineation over all organs for all subjects as expressed in TPVF and FPVF is 93.01% and 0.22%, and all foot bones for

  10. Incorporation of the concept of microbial product formation into ASM3 and the modeling of a membrane bioreactor for wastewater treatment

    Directory of Open Access Journals (Sweden)

    K. P. Oliveira-Esquerre

    2006-12-01

    Full Text Available This paper proposes a modification of ASM3 in a way that takes into account the process of production and consumption of microbial products (MPs in a submerged membrane bioreactor fed with the effluent of a particular precoagulation sedimentation unit. A comparative representation of the modeling results obtained with ASM3 and ASM1 is performed and it highlights the importance of considering the process of storage of organic substrate, including MPs, as a prior step to bacterial growth. In addition to the suspended solids and microorganisms, various soluble organic substances, which might be either undecomposed organic substances contained in the raw water or MPs, are assumed to be selectively retained within the bioreactor. The results show that the carbonaceous materials are more accurately estimated by ASM3, while ASM1 performs slightly better than ASM3 in the estimation of nitrate. The estimated MP concentration in the mixed liquor and permeate agrees with the experimental evidence, and as expected, MPs play a role in supplying organic substrate to heterotrophs in both ASM1 and ASM3.

  11. Interaction between endoplasmic/sarcoplasmic reticulum stress (ER/SR stress), mitochondrial signaling and Ca(2+) regulation in airway smooth muscle (ASM).

    Science.gov (United States)

    Delmotte, Philippe; Sieck, Gary C

    2015-02-01

    Airway inflammation is a key aspect of diseases such as asthma. Several inflammatory cytokines (e.g., TNFα and IL-13) increase cytosolic Ca(2+) ([Ca(2+)]cyt) responses to agonist stimulation and Ca(2+) sensitivity of force generation, thereby enhancing airway smooth muscle (ASM) contractility (hyper-reactive state). Inflammation also induces ASM proliferation and remodeling (synthetic state). In normal ASM, the transient elevation of [Ca(2+)]cyt induced by agonists leads to a transient increase in mitochondrial Ca(2+) ([Ca(2+)]mito) that may be important in matching ATP production with ATP consumption. In human ASM (hASM) exposed to TNFα and IL-13, the transient increase in [Ca(2+)]mito is blunted despite enhanced [Ca(2+)]cyt responses. We also found that TNFα and IL-13 induce reactive oxidant species (ROS) formation and endoplasmic/sarcoplasmic reticulum (ER/SR) stress (unfolded protein response) in hASM. ER/SR stress in hASM is associated with disruption of mitochondrial coupling with the ER/SR membrane, which relates to reduced mitofusin 2 (Mfn2) expression. Thus, in hASM it appears that TNFα and IL-13 result in ROS formation leading to ER/SR stress, reduced Mfn2 expression, disruption of mitochondrion-ER/SR coupling, decreased mitochondrial Ca(2+) buffering, mitochondrial fragmentation, and increased cell proliferation.

  12. Design and Analysis of Boiler Pressure Vessels based on IBR codes

    Science.gov (United States)

    Balakrishnan, B.; Kanimozhi, B.

    2017-05-01

    Pressure vessels components are widely used in the thermal and nuclear power plants for generating steam using the philosophy of heat transfer. In Thermal power plant, Coal is burnt inside the boiler furnace for generating the heat. The amount of heat produced through the combustion of pulverized coal is used in changing the phase transfer (i.e. Water into Super-Heated Steam) in the Pressure Parts Component. Pressure vessels are designed as per the Standards and Codes of the country, where the boiler is to be installed. One of the Standards followed in designing Pressure Parts is ASME (American Society of Mechanical Engineers). The mandatory requirements of ASME code must be satisfied by the manufacturer. In our project case, A Shell/pipe which has been manufactured using ASME code has an issue during the drilling of hole. The Actual Size of the drilled holes must be, as per the drawing, but due to error, the size has been differentiate from approved design calculation (i.e. the diameter size has been exceeded). In order to rectify this error, we have included an additional reinforcement pad to the drilled and modified the design of header in accordance with the code requirements.

  13. IM (Integrity Management) software must show flexibility to local codes

    Energy Technology Data Exchange (ETDEWEB)

    Brors, Markus [ROSEN Technology and Research Center GmbH (Germany); Diggory, Ian [Macaw Engineering Ltd., Northumberland (United Kingdom)

    2009-07-01

    There are many internationally recognized codes and standards, such as API 1160 and ASME B31.8S, which help pipeline operators to manage and maintain the integrity of their pipeline networks. However, operators in many countries still use local codes that often reflect the history of pipeline developments in their region and are based on direct experience and research on their pipelines. As pipeline companies come under increasing regulatory and financial pressures to maintain the integrity of their networks, it is important that operators using regional codes are able to benchmark their integrity management schemes against these international standards. Any comprehensive Pipeline Integrity Management System (PIMS) software package should therefore not only incorporate industry standards for pipeline integrity assessment but also be capable of implementing regional codes for comparison purposes. This paper describes the challenges and benefits of incorporating one such set of regional pipeline standards into ROSEN Asset Integrity Management Software (ROAIMS). (author)

  14. Impact of the A18.1 ASME Standard on Platform Lifts and Stairway Chairlifts on Accessibility and Usability

    Science.gov (United States)

    Balmer, David C.

    2010-01-01

    This article summarizes the effect of the ASME A18.1 Standard concerning accessibility and usability of Platform Lifts and their remaining technological challenges. While elevators are currently the most effective means of vertical transportation related to speed, capacity, rise and usability, their major drawbacks for accessibility are cost and…

  15. Modeling Nitrous Oxide Production during Biological Nitrogen Removal via Nitrification and Denitrification: Extensions to the General ASM Models

    DEFF Research Database (Denmark)

    Ni, Bing-Jie; Ruscalleda, Maël; Pellicer i Nàcher, Carles

    2011-01-01

    Nitrous oxide (N2O) can be formed during biological nitrogen (N) removal processes. In this work, a mathematical model is developed that describes N2O production and consumption during activated sludge nitrification and denitrification. The well-known ASM process models are extended to capture N2O...

  16. Simulation of municipal-industrial full scale WWTP in an arid climate by application of ASM3

    Directory of Open Access Journals (Sweden)

    Abdelsalam Elawwad

    2017-03-01

    Full Text Available In developing countries, and due to the high cost of treatment of industrial wastewater, municipal wastewater treatment facilities usually receive a mixture of municipal wastewater and partially treated industrial wastewater. As a result, an increased potential for shock loads with high pollutant concentrations is expected. The use of mathematical modelling of wastewater treatment is highly efficient in such cases. A dynamic model based on activated sludge model no. 3 (ASM3 describing the performance of the activated sludge process at a full scale wastewater treatment plant (WWTP receiving mixed domestic–industrial wastewater located in an arid area is presented. ASM3 was extended by adding the Arrhenius equation to respond to changes in temperature. BioWin software V.4 was used as the model platform. The model was calibrated under steady-state conditions, adjusting only three kinetic and stoichiometric parameters: maximum heterotrophic growth rate (μH = 8 d−1, heterotrophic aerobic decay rate (bH, O2 = 0.18 d−1, and aerobic heterotrophic yield (YH,O2 = 0.4 (gCOD/gCOD. ASM3 was successful in predicting the WWTP performance, as the model was validated with 10 months of routine daily measurements. ASM3 extended with the Arrhenius equation could be helpful in the design and operation of WWTPs with mixed municipal–industrial influent in arid areas.

  17. Change of nonlinear acoustics in ASME grade 122 steel welded joint during creep

    Science.gov (United States)

    Ohtani, Toshihiro; Honma, Takumi; Ishii, Yutaka; Tabuchi, Masaaki; Hongo, Hiromichi; Hirao, Masahiko

    2016-02-01

    In this paper, we described the changes of two nonlinear acoustic characterizations; resonant frequency shift and three-wave interaction, with electromagnetic acoustic resonance (EMAR) throughout the creep life in the welded joints of ASME Grade 122, one of high Cr ferritic heat resisting steels. EMAR was a combination of the resonant acoustic technique with a non-contact electromagnetic acoustic transducer (EMAT). These nonlinear acoustic parameters decreased from the start to 50% of creep life. After slightly increased, they rapidly increased from 80% of creep life to rupture. We interpreted these phenomena in terms of dislocation recovery, recrystallization, and restructuring related to the initiation and growth of creep void, with support from the SEM and TEM observation.

  18. ASME B89.4.19 Performance Evaluation Tests and Geometric Misalignments in Laser Trackers.

    Science.gov (United States)

    Muralikrishnan, B; Sawyer, D; Blackburn, C; Phillips, S; Borchardt, B; Estler, W T

    2009-01-01

    Small and unintended offsets, tilts, and eccentricity of the mechanical and optical components in laser trackers introduce systematic errors in the measured spherical coordinates (angles and range readings) and possibly in the calculated lengths of reference artifacts. It is desirable that the tests described in the ASME B89.4.19 Standard [1] be sensitive to these geometric misalignments so that any resulting systematic errors are identified during performance evaluation. In this paper, we present some analysis, using error models and numerical simulation, of the sensitivity of the length measurement system tests and two-face system tests in the B89.4.19 Standard to misalignments in laser trackers. We highlight key attributes of the testing strategy adopted in the Standard and propose new length measurement system tests that demonstrate improved sensitivity to some misalignments. Experimental results with a tracker that is not properly error corrected for the effects of the misalignments validate claims regarding the proposed new length tests.

  19. Linearization in ASM1 model for the solution of pollutants transport equations

    Directory of Open Access Journals (Sweden)

    Neyva Maria Lopes Romeiro

    2008-08-01

    Full Text Available It is proposed to reduce the complexity existing in non-linear BIOMOC and ASM1 models using Taylor’s frst-order series expansion in the terms whose reactive processes are non-linear. One of the advantages of linear models is the conservation of non-linear model variables. However, the main characteristic of this methodology refers to the computational time obtained in the numeral simulations, which is much shorter than that concerning the non-linear model results. Numerical results are presented, showing the effciency, precision and solidity of the proposed technique in well-known cases in the literature, using the semi-discrete method of finite elements.

  20. Using ASM Podcasts to Excite Undergraduate Students about Current Microbiological Research

    Directory of Open Access Journals (Sweden)

    Stacey E. Lettini

    2014-08-01

    Full Text Available Innovative technology is often used as a mechanism to engage students in and out of the classroom and can be used to increase critical thinking skills. Podcasts are an excellent way to introduce students to current topics and research in microbiology. The American Society for Microbiology (ASM produces three podcasts that are microbiologically focused: This Week in Microbiology (TWiM, This Week in Parasitology (TWiP, and This Week in Virology (TWiV. These podcasts are usually presented in a manner similar to a journal club, as the presenters regularly invite guests to discuss current research papers. Since students often find reading scientific literature difficult and get bogged down in the details rather than seeing the over-arching purpose of a paper, these podcasts have been used in a General Microbiology course to introduce recent research articles. The students were first assigned an original research article to read and review, and they were asked to generate questions pertaining to things they did not understand. Next, students listened to the corresponding podcast that discussed the article and used it to answer their questions. This was followed by a classroom discussion of the article and the podcast. The ASM podcast helped to demystify original research by providing details of the experimental design and presentation of the results in a language that is more casual and relatable. Students demonstrated greater critical thinking and comprehension of microbiology literature after listening to the podcast. This activity can be used in a variety of courses in the biology curriculum.

  1. User-inspired design methodology using Affordance Structure Matrix (ASM for construction projects

    Directory of Open Access Journals (Sweden)

    Maheswari J. Uma

    2017-01-01

    Full Text Available Traditionally, design phase of construction projects is often performed with incomplete and inaccurate user preferences. This is due to inefficiencies in the methodologies used for capturing the user requirements that can subsequently lead to inconsistencies and result in non-optimised end-result. Iterations and subsequent reworks due to such design inefficiencies is one of the major reasons for unsuccessful project delivery as they impact project performance measures such as time and cost among others. The existing design theories and practice are primarily based on functional requirements. Function-based design deals with design of artifact alone, which may yield favourable or unfavourable consequences with the design artifact. However, incorporating other interactions such as interactions between user & designer is necessary for optimised end-result. Hence, the objective of this research work is to devise a systematic design methodology considering all the three interactions among users, designers and artefacts for improved design efficiency. In this study, it has been attempted to apply the theory of affordances in a case project that involves the design of an offshore facility. A step-by-step methodology for developing Affordance Structure Matrix (ASM, which integrates House of Quality (HOQ and Design Structure Matrix (DSM, is proposed that can effectively capture the user requirements. HOQ is a popular quality management tool for capturing client requirements and DSM is a matrix-based tool that can capture the interdependency among the design entities. The proposed methodology utilises the strengths of both the tools, as DSM compliments HOQ in the process. In this methodology, different affordances such as AUA (Artifact-User-Affordance, AAA (Artifact-Artifact-Affordance and DDA (Designer-Designer-Affordance are captured systematically. Affordance is considered to be user-driven in this context that is in contrast to prevailing design

  2. Network Coding

    Indian Academy of Sciences (India)

    message symbols downstream, network coding achieves vast performance gains by permitting intermediate nodes to carry out algebraic oper- ations on the incoming data. In this article we present a tutorial introduction to network coding as well as an application to the e±cient operation of distributed data-storage networks.

  3. Verification of Allowable Stresses In ASME Section III Subsection NH For Grade 91 Steel & Alloy 800H

    Energy Technology Data Exchange (ETDEWEB)

    R. W. Swindeman; M. J. Swindeman; B. W. Roberts; B. E. Thurgood; D. L. Marriott

    2007-11-30

    The database for the creep-rupture of 9Cr-1Mo-V (Grade 91) steel was collected and reviewed to determine if it met the needs for recommending time-dependent strength values, S{sub t}, for coverage in ASME Section III Subsection NH (ASME III-NH) to 650 C (1200 F) and 600,000 hours. The accumulated database included over 300 tests for 1% total strain, nearly 400 tests for tertiary creep, and nearly 1700 tests to rupture. Procedures for analyzing creep and rupture data for ASME III-NH were reviewed and compared to the procedures used to develop the current allowable stress values for Gr 91 for ASME II-D. The criteria in ASME III-NH for estimating S{sub t} included the average strength for 1% total strain for times to 600,000 hours, 80% of the minimum strength for tertiary creep for times to 600,000 hours, and 67% of the minimum rupture strength values for times to 600,000 hours. Time-temperature-stress parametric formulations were selected to correlate the data and make predictions of the long-time strength. It was found that the stress corresponding to 1% total strain and the initiation of tertiary creep were not the controlling criteria over the temperature-time range of concern. It was found that small adjustments to the current values in III-NH could be introduced but that the existing values were conservative and could be retained. The existing database was found to be adequate to extend the coverage to 600,000 hours for temperatures below 650 C (1200 F).

  4. Corticosteroid-Induced MKP-1 Represses Pro-Inflammatory Cytokine Secretion by Enhancing Activity of Tristetraprolin (TTP) in ASM Cells.

    Science.gov (United States)

    Prabhala, Pavan; Bunge, Kristin; Ge, Qi; Ammit, Alaina J

    2016-10-01

    Exaggerated cytokine secretion drives pathogenesis of a number of chronic inflammatory diseases, including asthma. Anti-inflammatory pharmacotherapies, including corticosteroids, are front-line therapies and although they have proven clinical utility, the molecular mechanisms responsible for their actions are not fully understood. The corticosteroid-inducible gene, mitogen-activated protein kinase (MAPK) phosphatase 1 (MKP-1, DUSP1) has emerged as a key molecule responsible for the repressive effects of steroids. MKP-1 is known to deactivate p38 MAPK phosphorylation and can control the expression and activity of the mRNA destabilizing protein-tristetraprolin (TTP). But whether corticosteroid-induced MKP-1 acts via p38 MAPK-mediated modulation of TTP function in a pivotal airway cell type, airway smooth muscle (ASM), was unknown. While pretreatment of ASM cells with the corticosteroid dexamethasone (preventative protocol) is known to reduce ASM synthetic function in vitro, the impact of adding dexamethasone after stimulation (therapeutic protocol) had not been explored. Whether dexamethasone modulates TTP in a p38 MAPK-dependent manner in this cell type was also unknown. We address this herein and utilize an in vitro model of asthmatic inflammation where ASM cells were stimulated with the pro-asthmatic cytokine tumor necrosis factor (TNF) and the impact of adding dexamethasone 1 h after stimulation assessed. IL-6 mRNA expression and protein secretion was significantly repressed by dexamethasone acting in a temporally distinct manner to increase MKP-1, deactivate p38 MAPK, and modulate TTP phosphorylation status. In this way, dexamethasone-induced MKP-1 acts via p38 MAPK to switch on the mRNA destabilizing function of TTP to repress pro-inflammatory cytokine secretion from ASM cells. J. Cell. Physiol. 231: 2153-2158, 2016. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  5. Spectrum of SMPD1 mutations in Asian-Indian patients with acid sphingomyelinase (ASM)-deficient Niemann-Pick disease.

    Science.gov (United States)

    Ranganath, Prajnya; Matta, Divya; Bhavani, Gandham SriLakshmi; Wangnekar, Savita; Jain, Jamal Mohammed Nurul; Verma, Ishwar C; Kabra, Madhulika; Puri, Ratna Dua; Danda, Sumita; Gupta, Neerja; Girisha, Katta M; Sankar, Vaikom H; Patil, Siddaramappa J; Ramadevi, Akella Radha; Bhat, Meenakshi; Gowrishankar, Kalpana; Mandal, Kausik; Aggarwal, Shagun; Tamhankar, Parag Mohan; Tilak, Preetha; Phadke, Shubha R; Dalal, Ashwin

    2016-10-01

    Acid sphingomyelinase (ASM)-deficient Niemann-Pick disease is an autosomal recessive lysosomal storage disorder caused by biallelic mutations in the SMPD1 gene. To date, around 185 mutations have been reported in patients with ASM-deficient NPD world-wide, but the mutation spectrum of this disease in India has not yet been reported. The aim of this study was to ascertain the mutation profile in Indian patients with ASM-deficient NPD. We sequenced SMPD1 in 60 unrelated families affected with ASM-deficient NPD. A total of 45 distinct pathogenic sequence variants were found, of which 14 were known and 31 were novel. The variants included 30 missense, 4 nonsense, and 9 frameshift (7 single base deletions and 2 single base insertions) mutations, 1 indel, and 1 intronic duplication. The pathogenicity of the novel mutations was inferred with the help of the mutation prediction software MutationTaster, SIFT, Polyphen-2, PROVEAN, and HANSA. The effects of the identified sequence variants on the protein structure were studied using the structure modeled with the help of the SWISS-MODEL workspace program. The p. (Arg542*) (c.1624C>T) mutation was the most commonly identified mutation, found in 22% (26 out of 120) of the alleles tested, but haplotype analysis for this mutation did not identify a founder effect for the Indian population. To the best of our knowledge, this is the largest study on mutation analysis of patients with ASM-deficient Niemann-Pick disease reported in literature and also the first study on the SMPD1 gene mutation spectrum in India. © 2016 Wiley Periodicals, Inc. © 2016 Wiley Periodicals, Inc.

  6. Reliability based code calibration of fatigue design criteria of nuclear Class-1 piping

    International Nuclear Information System (INIS)

    Mishra, J.; Balasubramaniyan, V.; Chellapandi, P.

    2016-01-01

    Fatigue design of Class-l piping of NPP is carried out using Section-III of American Society of Mechanical Engineers (ASME) Boiler and Pressure Vessel code. The fatigue design criteria of ASME are based on the concept of safety factor, which does not provide means for the management of uncertainties for consistently reliable and economical designs. In this regards, a work is taken up to estimate the implicit reliability level associated with fatigue design criteria of Class-l piping specified by ASME Section III, NB-3650. As ASME fatigue curve is not in the form of analytical expression, the reliability level of pipeline fittings and joints is evaluated using the mean fatigue curve developed by Argonne National Laboratory (ANL). The methodology employed for reliability evaluation is FORM, HORSM and MCS. The limit state function for fatigue damage is found to be sensitive to eight parameters, which are systematically modelled as stochastic variables during reliability estimation. In conclusion a number of important aspects related to reliability of various piping product and joints are discussed. A computational example illustrates the developed procedure for a typical pipeline. (author)

  7. Draft ASME Boiler and Pressure Vessel Code Section III, Division 5, Section HB, Subsection B, Code Case for Alloy 617 and Background Documentation

    Energy Technology Data Exchange (ETDEWEB)

    Wright, Julie Knibloe [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2015-08-01

    Alloy 617 is the leading candidate material for an intermediate heat exchanger for the very high temperature reactor. To evaluate the behavior of this material in the expected service conditions, strain controlled cyclic tests that include long hold times up to 240 minutes at maximum tensile strain were conducted at 850°C. In terms of the total number of cycles to failure, the fatigue resistance decreased when a hold time was added at peak tensile strain. Increases in the tensile hold duration degraded the creep fatigue resistance, at least to the investigated strain controlled hold time of up to 60 minutes at the 0.3% strain range and 240 minutes at the 1.0% strain range. The creep fatigue deformation mode is considered relative to the lack of saturation, or continually decreasing number of cycles to failure with increasing hold times. Additionally, preliminary values from the 850°C creep fatigue data are calculated for the creep fatigue damage diagram and have higher values of creep damage than those from tests at 950°C.

  8. ASME Section VIII Recertification of a 33,000 Gallon Vacuum-jacketed LH2 Storage Vessel for Densified Hydrogen Testing at NASA Kennedy Space Center

    Science.gov (United States)

    Swanger, Adam M.; Notardonato, William U.; Jumper, Kevin M.

    2015-01-01

    The Ground Operations Demonstration Unit for Liquid Hydrogen (GODU-LH2) has been developed at NASA Kennedy Space Center in Florida. GODU-LH2 has three main objectives: zero-loss storage and transfer, liquefaction, and densification of liquid hydrogen. A cryogenic refrigerator has been integrated into an existing, previously certified, 33,000 gallon vacuum-jacketed storage vessel built by Minnesota Valley Engineering in 1991 for the Titan program. The dewar has an inner diameter of 9.5 and a length of 71.5; original design temperature and pressure ranges are -423 F to 100 F and 0 to 95 psig respectively. During densification operations the liquid temperature will be decreased below the normal boiling point by the refrigerator, and consequently the pressure inside the inner vessel will be sub-atmospheric. These new operational conditions rendered the original certification invalid, so an effort was undertaken to recertify the tank to the new pressure and temperature requirements (-12.7 to 95 psig and -433 F to 100 F respectively) per ASME Boiler and Pressure Vessel Code, Section VIII, Division 1. This paper will discuss the unique design, analysis and implementation issues encountered during the vessel recertification process.

  9. Coding Class

    DEFF Research Database (Denmark)

    Ejsing-Duun, Stine; Hansbøl, Mikala

    Denne rapport rummer evaluering og dokumentation af Coding Class projektet1. Coding Class projektet blev igangsat i skoleåret 2016/2017 af IT-Branchen i samarbejde med en række medlemsvirksomheder, Københavns kommune, Vejle Kommune, Styrelsen for IT- og Læring (STIL) og den frivillige forening......, design tænkning og design-pædagogik, Stine Ejsing-Duun fra Forskningslab: It og Læringsdesign (ILD-LAB) ved Institut for kommunikation og psykologi, Aalborg Universitet i København. Vi har fulgt og gennemført evaluering og dokumentation af Coding Class projektet i perioden november 2016 til maj 2017....... Coding Class projektet er et pilotprojekt, hvor en række skoler i København og Vejle kommuner har igangsat undervisningsaktiviteter med fokus på kodning og programmering i skolen. Evalueringen og dokumentationen af projektet omfatter kvalitative nedslag i udvalgte undervisningsinterventioner i efteråret...

  10. Coding Labour

    Directory of Open Access Journals (Sweden)

    Anthony McCosker

    2014-03-01

    Full Text Available As well as introducing the Coding Labour section, the authors explore the diffusion of code across the material contexts of everyday life, through the objects and tools of mediation, the systems and practices of cultural production and organisational management, and in the material conditions of labour. Taking code beyond computation and software, their specific focus is on the increasingly familiar connections between code and labour with a focus on the codification and modulation of affect through technologies and practices of management within the contemporary work organisation. In the grey literature of spreadsheets, minutes, workload models, email and the like they identify a violence of forms through which workplace affect, in its constant flux of crisis and ‘prodromal’ modes, is regulated and governed.

  11. Speech coding

    Energy Technology Data Exchange (ETDEWEB)

    Ravishankar, C., Hughes Network Systems, Germantown, MD

    1998-05-08

    Speech is the predominant means of communication between human beings and since the invention of the telephone by Alexander Graham Bell in 1876, speech services have remained to be the core service in almost all telecommunication systems. Original analog methods of telephony had the disadvantage of speech signal getting corrupted by noise, cross-talk and distortion Long haul transmissions which use repeaters to compensate for the loss in signal strength on transmission links also increase the associated noise and distortion. On the other hand digital transmission is relatively immune to noise, cross-talk and distortion primarily because of the capability to faithfully regenerate digital signal at each repeater purely based on a binary decision. Hence end-to-end performance of the digital link essentially becomes independent of the length and operating frequency bands of the link Hence from a transmission point of view digital transmission has been the preferred approach due to its higher immunity to noise. The need to carry digital speech became extremely important from a service provision point of view as well. Modem requirements have introduced the need for robust, flexible and secure services that can carry a multitude of signal types (such as voice, data and video) without a fundamental change in infrastructure. Such a requirement could not have been easily met without the advent of digital transmission systems, thereby requiring speech to be coded digitally. The term Speech Coding is often referred to techniques that represent or code speech signals either directly as a waveform or as a set of parameters by analyzing the speech signal. In either case, the codes are transmitted to the distant end where speech is reconstructed or synthesized using the received set of codes. A more generic term that is applicable to these techniques that is often interchangeably used with speech coding is the term voice coding. This term is more generic in the sense that the

  12. IL-17A acts via p38 MAPK to increase stability of TNF-alpha-induced IL-8 mRNA in human ASM.

    Science.gov (United States)

    Henness, Sheridan; van Thoor, Eveline; Ge, Qi; Armour, Carol L; Hughes, J Margaret; Ammit, Alaina J

    2006-06-01

    Human airway smooth muscle (ASM) plays an immunomodulatory role in asthma. Recently, IL-17A has become of increasing interest in asthma, being found at elevated levels in asthmatic airways and emerging as playing an important role in airway neutrophilia. IL-17A predominantly exerts its neutrophil orchestrating role indirectly via the induction of cytokines by resident airway structural cells. Here, we perform an in vitro study to show that although IL-17A did not induce secretion of the CXC chemokine IL-8 from ASM cells, IL-17A significantly potentiates TNF-alpha-induced IL-8 protein secretion and gene expression in a concentration- and time-dependent manner (P ASM cells, acting via a p38 MAPK-dependent posttranscriptional pathway to augment TNF-alpha-induced secretion of the potent neutrophil chemoattractant IL-8 from ASM cells.

  13. Activated sludge model (ASM) based modelling of membrane bioreactor (MBR) processes: a critical review with special regard to MBR specificities.

    Science.gov (United States)

    Fenu, A; Guglielmi, G; Jimenez, J; Spèrandio, M; Saroj, D; Lesjean, B; Brepols, C; Thoeye, C; Nopens, I

    2010-08-01

    Membrane bioreactors (MBRs) have been increasingly employed for municipal and industrial wastewater treatment in the last decade. The efforts for modelling of such wastewater treatment systems have always targeted either the biological processes (treatment quality target) as well as the various aspects of engineering (cost effective design and operation). The development of Activated Sludge Models (ASM) was an important evolution in the modelling of Conventional Activated Sludge (CAS) processes and their use is now very well established. However, although they were initially developed to describe CAS processes, they have simply been transferred and applied to MBR processes. Recent studies on MBR biological processes have reported several crucial specificities: medium to very high sludge retention times, high mixed liquor concentration, accumulation of soluble microbial products (SMP) rejected by the membrane filtration step, and high aeration rates for scouring purposes. These aspects raise the question as to what extent the ASM framework is applicable to MBR processes. Several studies highlighting some of the aforementioned issues are scattered through the literature. Hence, through a concise and structured overview of the past developments and current state-of-the-art in biological modelling of MBR, this review explores ASM-based modelling applied to MBR processes. The work aims to synthesize previous studies and differentiates between unmodified and modified applications of ASM to MBR. Particular emphasis is placed on influent fractionation, biokinetics, and soluble microbial products (SMPs)/exo-polymeric substances (EPS) modelling, and suggestions are put forward as to good modelling practice with regard to MBR modelling both for end-users and academia. A last section highlights shortcomings and future needs for improved biological modelling of MBR processes. (c) 2010 Elsevier Ltd. All rights reserved.

  14. Flujo espiratorio máximo en niños asmáticos: Casos y controles

    Directory of Open Access Journals (Sweden)

    Arturo Recabarren Lozada

    1995-04-01

    Full Text Available Con el fin de determinar las variaciones del Flujo Espiratorio Máximo (PEF, se estudiaron a 38 niños asmáticos (CASOS en período intercrítico de la enfermedad y a 38 niños sanos (CONTROLES, de ambos sexos comprendidos entre los 5 y 15 años de edad. Los niños asmáticos fueron clasificados por parámetros clínicos en determinado grado de severidad de asma bronquial, determinando el PEF de cada niño objeto de estudio conel mini-Wright Peak Flow Meter, en 2 registros diarios a los 06 y 18 horas, durante 7 días consecutivos, obteniendo la variabilidad del mismo. Se encuentra diferencia en la variabilidad global de niños asmáticos de todos los grados de severidad de la enfermedad comprada con la de los niños normales, con diferencia estadística altamente significativa (p<0.000001. Las variaciones diurnas del PEF ayuda en el diagnóstico del asma bronquial y también son útiles para realizar la catalogación de severidad de la enfermedad. El PEF correlaciona bien con los síntomas presentados por los pacientes y por lo tanto guarda correspondencia con la Hiperreactividad bronquial (HRB del niño asmático. Postulamos que un niño con historia clínica sugestiva, una variabilidad global mayor del 8% indica que el diagnóstico de asma es altamente probable (Rev Med Hered 1995; 6: 76-82

  15. ASME B89.4.19 Performance Evaluation Tests and Geometric Misalignments in Laser Trackers

    Directory of Open Access Journals (Sweden)

    Muralikrishnan, Bala

    2009-01-01

    Full Text Available Small and unintended offsets, tilts, and eccentricity of the mechanical and optical components in laser trackers introduce systematic errors in the measured spherical coordinates (angles and range readings and possibly in the calculated lengths of reference artifacts. It is desirable that the tests described in the ASME B89.4.19 Standard [1] be sensitive to these geometric misalignments so that any resulting systematic errors are identified during performance evaluation. In this paper, we present some analysis, using error models and numerical simulation, of the sensitivity of the length measurement system tests and two-face system tests in the B89.4.19 Standard to misalignments in laser trackers. We highlight key attributes of the testing strategy adopted in the Standard and propose new length measurement system tests that demonstrate improved sensitivity to some misalignments. Experimental results with a tracker that is not properly error corrected for the effects of the misalignments validate claims regarding the proposed new length tests.

  16. ASM-Triggered Too Observations of Kilohertz Oscillations in Three Atoll Sources

    Science.gov (United States)

    Kaaret, P.; Swank, Jean (Technical Monitor)

    2000-01-01

    Three Rossi Timing Explorer (RXTE) observations were carried out for this proposal based on target of opportunity triggers derived from the All-Sky Monitor (ASM) on RXTE. We obtained short observations of 4U1636-536 (15ks) and 4U1735-44 (23ks) and a longer observation of 4U0614+091 (117ks). Our analysis of our observations of the atoll neutron star x-ray binary 4U1735-44 lead to the discovery of a second high frequency quasiperiodic oscillation (QPO) in this source. These results were published in the Astrophysical Journal Letters. The data obtained on the source 4U0614+091 were used in a comprehensive study of this source, which will be published in the Astrophysical Journal. The data from this proposal were particularly critical for that study as they lead to the detection of the highest QPO frequency every found in the x-ray emission from an x-ray binary which will be important in placing limits on the equation of state of nuclear matter.

  17. 2016 ASMS Workshop Review: Next Generation LC/MS: Critical Insights and Future Perspectives

    Energy Technology Data Exchange (ETDEWEB)

    Gao, Hongying; Makarov, Alexander; Smith, Richard D.

    2017-04-17

    The pilot workshop on BNext Generation LC/MS: Critical Insights and Future Perspectives was held on the evening of June 6, 2016 at the 64th ASMS Conference on Mass Spectrometry and Allied Topics held in San Antonio, TX. The workshop, chaired by Hongying Gao (Pfizer), consisted of stimulating talks from distinguished speakers and open discussion among the audience and invited presenters.The objectives of this workshop were to better understand the advances and limitations of current technologies; to exchange perspectives on the next generation LC/MS; and to discuss/debate the features of next generation LC/MS focusing on the following three questions: (1) What would the next generation LC/MS look like? (2) How would it change the way we do analysis? and (3) What fundamental issues need to be resolved? A real-world case in the biopharmaceutical industry was presented by Hongying Gao on the needs by industry for LC/MS innovation and technology advancements. The primary invited speakers were Alexander Makarov (Thermo Fisher Scientific) and Richard (Dick) Smith (Pacific Northwest National Laboratory). The open discussions started with Q&A and comments for Alexander Makarov and Dick Smith, followed by insights and perspectives from members of the audience and other invited presenters who shared their thoughts addressing the above questions.

  18. NSURE code

    International Nuclear Information System (INIS)

    Rattan, D.S.

    1993-11-01

    NSURE stands for Near-Surface Repository code. NSURE is a performance assessment code. developed for the safety assessment of near-surface disposal facilities for low-level radioactive waste (LLRW). Part one of this report documents the NSURE model, governing equations and formulation of the mathematical models, and their implementation under the SYVAC3 executive. The NSURE model simulates the release of nuclides from an engineered vault, their subsequent transport via the groundwater and surface water pathways tot he biosphere, and predicts the resulting dose rate to a critical individual. Part two of this report consists of a User's manual, describing simulation procedures, input data preparation, output and example test cases

  19. Speaking Code

    DEFF Research Database (Denmark)

    Cox, Geoff

    Speaking Code begins by invoking the “Hello World” convention used by programmers when learning a new language, helping to establish the interplay of text and code that runs through the book. Interweaving the voice of critical writing from the humanities with the tradition of computing and softwa...... expression in the public realm. The book’s line of argument defends language against its invasion by economics, arguing that speech continues to underscore the human condition, however paradoxical this may seem in an era of pervasive computing....

  20. Iterative and non-iterative solutions of engine flows using ASM and k-ε turbulence models

    International Nuclear Information System (INIS)

    Khaleghi, H.; Fallah, E.

    2003-01-01

    Various turbulent models are widely developed in order to make a good prediction of turbulence phenomena in different applications. The standard k-ε model shows a poor prediction for some applications. The Reynolds Stress Model (RSM) is expected to give a better prediction of turbulent characteristics, because a separate differential equation for each Reynolds stress component is solved in this model. In order to save both time and memory in this calculation a new Algebraic Stress Model (ASM) which was developed by Lumly et al in 1995 is used for calculations of flow characteristics in the internal combustion engine chamber. With using turbulent realizability principles, this model becomes a powerful and reliable turbulence model. In this paper the abilities of the model is examined in internal combustion engine flows. The results of ASM and k-ε models are compared with the experimental data. It is shown that the poor predictions of k-ε model are modified by ASM model. Also in this paper non-iterative PISO and iterative SIMPLE solution algorithms are compared. The results show that the PISO solution algorithm is the preferred and more efficient procedure in the calculation of internal combustion engine. (author)

  1. Statistical re-evaluation of the ASME K{sub IC} and K{sub IR} fracture toughness reference curves

    Energy Technology Data Exchange (ETDEWEB)

    Wallin, K.; Rintamaa, R. [Valtion Teknillinen Tutkimuskeskus, Espoo (Finland)

    1998-11-01

    Historically the ASME reference curves have been treated as representing absolute deterministic lower bound curves of fracture toughness. In reality, this is not the case. They represent only deterministic lower bound curves to a specific set of data, which represent a certain probability range. A recently developed statistical lower bound estimation method called the `Master curve`, has been proposed as a candidate for a new lower bound reference curve concept. From a regulatory point of view, the Master curve is somewhat problematic in that it does not claim to be an absolute deterministic lower bound, but corresponds to a specific theoretical failure probability that can be chosen freely based on application. In order to be able to substitute the old ASME reference curves with lower bound curves based on the master curve concept, the inherent statistical nature (and confidence level) of the ASME reference curves must be revealed. In order to estimate the true inherent level of safety, represented by the reference curves, the original data base was re-evaluated with statistical methods and compared to an analysis based on the master curve concept. The analysis reveals that the 5% lower bound Master curve has the same inherent degree of safety as originally intended for the K{sub IC}-reference curve. Similarly, the 1% lower bound Master curve corresponds to the K{sub IR}-reference curve. (orig.)

  2. Modeling a bench-scale alternating aerobic/anoxic activated sludge system for nitrogen removal using a modified ASM1.

    Science.gov (United States)

    Kim, Hyunook; Noh, Soohong; Colosimo, Mark

    2009-07-01

    The Activated Sludge Model No. 1 (ASM1), developed by The International Association of Water Pollution Research and Control, was applied to model dynamics of NH4+, and NO3- in a bench scale alternating aerobic-anoxic (AAA) activated sludge system for nitrogen removal. The model was modified by eliminating inert soluble COD (S(I)) and inert particulate COD (X(I)) from the model's state variables as these two variables are not involved in any biological reaction and are not readily measurable with conventional routine COD analysis. It was assumed that the soluble COD and particulate COD of wastewater represent readily biodegradable COD (S(S)) and slowly biodegradable (X(S)) in the model, respectively. In addition, alkalinity was also removed from the model, since alkalinity of an AAA system remains stable due to the cyclic modes of the system. Even with the elimination of the three state variables and the assumption made, the model could reasonably predict the NH4+ and NO3- dynamics of the AAA system, and effluent NH4+ and NO3- concentrations with adjustment of only a few kinetic parameters. Compared to the original ASM1, it is expected that the modified ASM1 presented in this study can be more easily utilized by engineers in designing or operating an AAA system in practice, since it requires simple characterization of wastewater COD.

  3. Función adrenal y metabolismo lipídico en niños asmáticos tratados con budesonida

    Directory of Open Access Journals (Sweden)

    Paoli-de Valeri Mariela

    1999-01-01

    Full Text Available Objetivo. Evaluar el efecto de bajas dosis de budesonida inhalado sobre la función adrenal y el metabolismo lipídico en niños asmáticos. Material y métodos. Se estudiaron: 10 niños asmáticos (edad promedio, 8.6 años tratados con budesonida inhalado (200-300 µg/día por un lapso mayor a tres meses (grupo A; 15 niños asmáticos (edad promedio, 7.8 años sin tratamiento esteroideo (grupo B, y 10 niños no asmáticos (grupo C. Se determinaron los niveles de cortisol basal y postestímulo con ACTH, andrógenos adrenales, lípidos y cortisol urinario. Resultados. Entre los grupos A y B no hubo diferencias significativas en las variables estudiadas. En los niños asmáticos (grupo A-B el cortisol urinario fue significativamente mayor en relación con el grupo C. Los niveles de triglicéridos, colesterol total, colesterol de la lipoproteína de baja densidad e índices aterogénicos fueron mayores en el grupo de niños asmáticos, con y sin budesonida, comparados con el grupo C. Conclusiones. El tratamiento con dosis bajas de budesonida inhalado en niños asmáticos no modificó la función del eje adrenal ni el metabolismo lipídico. Los pacientes asmáticos presentaron un perfil lipídico aterogénico que podría incrementar el riesgo de enfermedad cardiovascular.

  4. The new topical ascomycin derivative SDZ ASM 981 does not induce skin atrophy when applied to normal skin for 4 weeks: a randomized, double-blind controlled study.

    Science.gov (United States)

    Queille-Roussel, C; Paul, C; Duteil, L; Lefebvre, M C; Rapatz, G; Zagula, M; Ortonne, J P

    2001-03-01

    SDZ ASM 981 is a selective inhibitor of inflammatory cytokines released from T lymphocytes and mast cells, which has been developed for the treatment of inflammatory skin diseases. In the present study, the atrophogenic potential of SDZ ASM 981 1% cream in humans was compared with that of medium and highly potent topical steroids, and vehicle. Four different preparations, SDZ ASM 981 1% cream, the corresponding vehicle of SDZ ASM 981 1% cream, betamethasone-17-valerate 0.1% cream and triamcinolone acetonide 0.1% cream, were applied to the volar aspect of the forearms of 16 healthy volunteers, twice daily, 6 days a week, for 4 weeks. Skin thickness was evaluated by ultrasound examination, clinical signs of atrophy by stereomicroscopy, and epidermal thickness was assessed by histology. Both topical corticosteroids induced a significant reduction in skin thickness, as compared with SDZ ASM 981 1% cream and vehicle, which were shown to be equivalent. The difference in skin thickness (measured by ultrasound examination) between patients treated with SDZ ASM 981 1% cream and those receiving either of the two topical steroids was significant from day 8 onwards. Histological analysis performed at day 29 showed significant epidermal thinning with topical steroids compared with SDZ ASM 981 1% cream or the vehicle. Conclusion The lack of atrophogenic properties of SDZ ASM 981 1% cream in this short-term study demonstrates its potential as long-term treatment for inflammatory skin diseases, thus overcoming a major drawback of topical steroids. This may also be important for the treatment of children, and sensitive areas of skin, such as the face and skin-folds.

  5. The Aster code; Code Aster

    Energy Technology Data Exchange (ETDEWEB)

    Delbecq, J.M

    1999-07-01

    The Aster code is a 2D or 3D finite-element calculation code for structures developed by the R and D direction of Electricite de France (EdF). This dossier presents a complete overview of the characteristics and uses of the Aster code: introduction of version 4; the context of Aster (organisation of the code development, versions, systems and interfaces, development tools, quality assurance, independent validation); static mechanics (linear thermo-elasticity, Euler buckling, cables, Zarka-Casier method); non-linear mechanics (materials behaviour, big deformations, specific loads, unloading and loss of load proportionality indicators, global algorithm, contact and friction); rupture mechanics (G energy restitution level, restitution level in thermo-elasto-plasticity, 3D local energy restitution level, KI and KII stress intensity factors, calculation of limit loads for structures), specific treatments (fatigue, rupture, wear, error estimation); meshes and models (mesh generation, modeling, loads and boundary conditions, links between different modeling processes, resolution of linear systems, display of results etc..); vibration mechanics (modal and harmonic analysis, dynamics with shocks, direct transient dynamics, seismic analysis and aleatory dynamics, non-linear dynamics, dynamical sub-structuring); fluid-structure interactions (internal acoustics, mass, rigidity and damping); linear and non-linear thermal analysis; steels and metal industry (structure transformations); coupled problems (internal chaining, internal thermo-hydro-mechanical coupling, chaining with other codes); products and services. (J.S.)

  6. ANIMAL code

    Energy Technology Data Exchange (ETDEWEB)

    Lindemuth, I.R.

    1979-02-28

    This report describes ANIMAL, a two-dimensional Eulerian magnetohydrodynamic computer code. ANIMAL's physical model also appears. Formulated are temporal and spatial finite-difference equations in a manner that facilitates implementation of the algorithm. Outlined are the functions of the algorithm's FORTRAN subroutines and variables.

  7. Network Coding

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 15; Issue 7. Network Coding. K V Rashmi Nihar B Shah P Vijay Kumar. General Article Volume 15 Issue 7 July 2010 pp 604-621. Fulltext. Click here to view fulltext PDF. Permanent link: https://www.ias.ac.in/article/fulltext/reso/015/07/0604-0621 ...

  8. ANIMAL code

    International Nuclear Information System (INIS)

    Lindemuth, I.R.

    1979-01-01

    This report describes ANIMAL, a two-dimensional Eulerian magnetohydrodynamic computer code. ANIMAL's physical model also appears. Formulated are temporal and spatial finite-difference equations in a manner that facilitates implementation of the algorithm. Outlined are the functions of the algorithm's FORTRAN subroutines and variables

  9. Expander Codes

    Indian Academy of Sciences (India)

    Codes and Channels. A noisy communication channel is illustrated in Fig- ... nication channel. Suppose we want to transmit a message over the unreliable communication channel so that even if the channel corrupts some of the bits we are able to recover ..... is d-regular, meaning thereby that every vertex has de- gree d.

  10. Expander Codes

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 10; Issue 1. Expander Codes - The Sipser–Spielman Construction. Priti Shankar. General Article Volume 10 ... Author Affiliations. Priti Shankar1. Department of Computer Science and Automation, Indian Institute of Science Bangalore 560 012, India.

  11. Network Coding

    Indian Academy of Sciences (India)

    Network coding is a technique to increase the amount of information °ow in a network by mak- ing the key observation that information °ow is fundamentally different from commodity °ow. Whereas, under traditional methods of opera- tion of data networks, intermediate nodes are restricted to simply forwarding their incoming.

  12. Panda code

    International Nuclear Information System (INIS)

    Altomare, S.; Minton, G.

    1975-02-01

    PANDA is a new two-group one-dimensional (slab/cylinder) neutron diffusion code designed to replace and extend the FAB series. PANDA allows for the nonlinear effects of xenon, enthalpy and Doppler. Fuel depletion is allowed. PANDA has a completely general search facility which will seek criticality, maximize reactivity, or minimize peaking. Any single parameter may be varied in a search. PANDA is written in FORTRAN IV, and as such is nearly machine independent. However, PANDA has been written with the present limitations of the Westinghouse CDC-6600 system in mind. Most computation loops are very short, and the code is less than half the useful 6600 memory size so that two jobs can reside in the core at once. (auth)

  13. An ASM/ADM model interface for dynamic plant-wide simulation.

    Science.gov (United States)

    Nopens, Ingmar; Batstone, Damien J; Copp, John B; Jeppsson, Ulf; Volcke, Eveline; Alex, Jens; Vanrolleghem, Peter A

    2009-04-01

    Mathematical modelling has proven to be very useful in process design, operation and optimisation. A recent trend in WWTP modelling is to include the different subunits in so-called plant-wide models rather than focusing on parts of the entire process. One example of a typical plant-wide model is the coupling of an upstream activated sludge plant (including primary settler, and secondary clarifier) to an anaerobic digester for sludge digestion. One of the key challenges when coupling these processes has been the definition of an interface between the well accepted activated sludge model (ASM1) and anaerobic digestion model (ADM1). Current characterisation and interface models have key limitations, the most critical of which is the over-use of X(c) (or lumped complex) variable as a main input to the ADM1. Over-use of X(c) does not allow for variation of degradability, carbon oxidation state or nitrogen content. In addition, achieving a target influent pH through the proper definition of the ionic system can be difficult. In this paper, we define an interface and characterisation model that maps degradable components directly to carbohydrates, proteins and lipids (and their soluble analogues), as well as organic acids, rather than using X(c). While this interface has been designed for use with the Benchmark Simulation Model No. 2 (BSM2), it is widely applicable to ADM1 input characterisation in general. We have demonstrated the model both hypothetically (BSM2), and practically on a full-scale anaerobic digester treating sewage sludge.

  14. Isolation and characterization of plantaricin ASM1: a new bacteriocin produced by Lactobacillus plantarum A-1.

    Science.gov (United States)

    Hata, Tomomi; Tanaka, Rie; Ohmomo, Sadahiro

    2010-01-31

    Bacteriocins produced by lactic acid bacteria showing stability even in neutral and weak alkaline pH were screened, and a new bacteriocin produced by Lactobacillus plantarum A-1, plantaricin ASM1 (PASM1) was purified and characterized. This bacteriocin which is heat-stable but digested by trypsin inhibits the growth of lactic acid bacterial species, such as Lactobacillus, Leuconostoc, and Enterococcus. PASM1 showed stability in a wide pH range compared to nisin A. The bacteriocin was purified using cation exchange, hydrophobic interaction, and reverse-phase high-performance liquid chromatography. The activity of the purified bacteriocin was obtained as one fraction. Matrix-assisted laser desorption/ionization time-of-flight mass spectrometry analysis of the fraction showed a mass of 5045.7Da. Combining the data obtained from amino acid and DNA sequencing, the primary sequence of PASM1 was determined. The sequence of the corresponding gene revealed that the peptide is ribosomally synthesized as a 64 amino acid precursor containing a 21 amino acid N-terminal extension of the double-glycine type. The mature peptide consists of 43 amino acids, which could contain two intramolecular disulfide bonds in the structure. Three putative open reading frames were located upstream of the PLNA1 gene. These genes may encode the thioredoxin family proteins and a response regulator both of which have been suggested to regulate expression of the PASM1 gene and the processing of its leader peptide. PASM1 has no reported homologue bacteriocins. Stability in a wide pH range and heat indicates its potential for application in food preservation. Copyright 2009 Elsevier B.V. All rights reserved.

  15. Effects of ASM-024, a modulator of acetylcholine receptor function, on airway responsiveness and allergen-induced responses in patients with mild asthma.

    Science.gov (United States)

    Boulet, Louis-Philippe; Gauvreau, Gail M; Cockcroft, Donald W; Davis, Beth; Vachon, Luc; Cormier, Yvon; O'Byrne, Paul M

    2015-01-01

    To evaluate the safety, tolerability and clinical activity of ASM-024, a new cholinergic compound with dual nicotinic and muscarinic activity, in mild allergic asthma. The present study involved 24 stable, mild allergic asthmatic subjects. In a cross-over design, ASM-024 (50 mg or 200 mg) or placebo were administered once daily by nebulization over three periods of nine consecutive days separated by a three-week washout. The effect of each treatment on the forced expiratory volume in 1 s (FEV1), provocative concentration of methacholine causing a 20% decline in FEV1 (PC20), early and late asthmatic responses, and allergen-induced inflammation were measured. Seventeen subjects completed the study. During treatment with ASM-024 at 50 mg or 200 mg, the PC20 value increased respectively from a mean (± SD) 2.56±3.86 mg/mL to 4.11 mg/mL (P=0.007), and from 3.12±4.37 mg/mL to 5.23 mg/mL (P=0.005) (no change with placebo). On day 7 (day preceding allergen challenge), postdosing FEV1 increased by 2.0% with 50 mg (P=0.005) and 1.9% with 200 mg (P=0.008) (placebo -1.1%). ASM-24 had no inhibitory effect on early and late asthmatic responses, nor on sputum eosinophil or neutrophil levels. ASM-024 induced no serious adverse events, but caused cough in 22% and 48% of the subjects with 50 mg and 200 mg, respectively, compared with 10% who were on placebo. ASM-024 did not inhibit allergen-induced asthmatic response and related airway inflammation, but reduced methacholine airway responsiveness and slightly improved lung function. The mechanism by which ASM-024 improves these outcomes requires further study.

  16. From concatenated codes to graph codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Høholdt, Tom

    2004-01-01

    We consider codes based on simple bipartite expander graphs. These codes may be seen as the first step leading from product type concatenated codes to more complex graph codes. We emphasize constructions of specific codes of realistic lengths, and study the details of decoding by message passing...

  17. Towards a consensus-based biokinetic model for green microalgae - The ASM-A.

    Science.gov (United States)

    Wágner, Dorottya S; Valverde-Pérez, Borja; Sæbø, Mariann; Bregua de la Sotilla, Marta; Van Wagenen, Jonathan; Smets, Barth F; Plósz, Benedek Gy

    2016-10-15

    Cultivation of microalgae in open ponds and closed photobioreactors (PBRs) using wastewater resources offers an opportunity for biochemical nutrient recovery. Effective reactor system design and process control of PBRs requires process models. Several models with different complexities have been developed to predict microalgal growth. However, none of these models can effectively describe all the relevant processes when microalgal growth is coupled with nutrient removal and recovery from wastewaters. Here, we present a mathematical model developed to simulate green microalgal growth (ASM-A) using the systematic approach of the activated sludge modelling (ASM) framework. The process model - identified based on a literature review and using new experimental data - accounts for factors influencing photoautotrophic and heterotrophic microalgal growth, nutrient uptake and storage (i.e. Droop model) and decay of microalgae. Model parameters were estimated using laboratory-scale batch and sequenced batch experiments using the novel Latin Hypercube Sampling based Simplex (LHSS) method. The model was evaluated using independent data obtained in a 24-L PBR operated in sequenced batch mode. Identifiability of the model was assessed. The model can effectively describe microalgal biomass growth, ammonia and phosphate concentrations as well as the phosphorus storage using a set of average parameter values estimated with the experimental data. A statistical analysis of simulation and measured data suggests that culture history and substrate availability can introduce significant variability on parameter values for predicting the reaction rates for bulk nitrate and the intracellularly stored nitrogen state-variables, thereby requiring scenario specific model calibration. ASM-A was identified using standard cultivation medium and it can provide a platform for extensions accounting for factors influencing algal growth and nutrient storage using wastewater resources. Copyright

  18. Acid sphingomyelinase (Asm) deficiency patients in The Netherlands and Belgium: disease spectrum and natural course in attenuated patients.

    Science.gov (United States)

    Hollak, C E M; de Sonnaville, E S V; Cassiman, D; Linthorst, G E; Groener, J E; Morava, E; Wevers, R A; Mannens, M; Aerts, J M F G; Meersseman, W; Akkerman, E; Niezen-Koning, K E; Mulder, M F; Visser, G; Wijburg, F A; Lefeber, D; Poorthuis, B J H M

    2012-11-01

    Niemann-Pick disease (NPD) is a neurovisceral lysosomal storage disorder caused by acid sphingomyelinase (ASM) deficiency, which can be categorized as either Niemann-Pick disease type A [NPD-A], with progressive neurological disease and death in early childhood, or as Niemann-Pick disease type B [NPD-B], with a more variable spectrum of manifestations. Enzyme replacement therapy (ERT) with recombinant sphingomyelinase is currently studied as potential treatment for NPD-B patients. The objective of this study is to characterize the clinical features of patients with ASM deficiency in the Netherlands and Belgium with focus on the natural disease course of NPD-B patients. Prospective and retrospective data on ASM deficient patients were collected in The Netherlands and part of Belgium. Patients with NPD-B that could be followed prospectively were evaluated every 6-12 months for pulmonary function tests, 6 minute walk test (6 MWT), imaging (bone marrow infiltration measured by QCSI, organ volumes by MRI and CT scan of the lungs) and biochemical markers. Twenty-five patients with ASM deficiency were identified (13 males, 12 females, median age 13years, range 1-59 years). Nine patients had died at the time of the study, including four NPD-A patients at the age of 1,1, 2, 3 and five NPDB patents at the age of 5, 6, 43, 56 and 60 years. There was a high prevalence of homozygosity and compound heterozygosity for the common p.Arg608del mutation in 43% and 19% of NPD-B patients, respectively. In NPD-B patients, thrombocytopenia was present in most, while anemia and leucopenia were less common (33% and 6 % respectively). HDL cholesterol was reduced in most patients. Pulmonary disease was severe in several patients. Follow-up up to 11 years revealed a gradual decrease in platelet count. Detailed investigations in 6 NPD-B patients with follow-up in 4 patients revealed remarkable stable disease parameters up to 6 years, with some decline in pulmonary function and 6 MWT. Bone

  19. Comparative studies on the effects of a yucca extract and acibenzolar-S-methyl (ASM) on inhibition of Venturia inaequalis in apple leaves

    DEFF Research Database (Denmark)

    Bengtsson, Marianne Vibeke; Wulff, Ednar Gadelha; Jørgensen, Hans Jørgen Lyngs

    2009-01-01

    and pathogen sporulation on leaves and both showed similar control efficacies as the reference treatment, sulphur. Whereas yucca extract and sulphur gave significant inhibition of conidial germination in vitro, ASM did not inhibit germination. Histopathological studies of the infection process of V. inaequalis...... in apple leaves showed that the yucca extract primarily acted by inhibiting pre-penetration events and penetration itself. In contrast, the ASM treatment significantly inhibited more stages of the infection process (pre-penetration, penetration and post-penetration events). These observations suggest...... was up-regulated following yucca treatment, to a level similar to that observed after treatment with ASM. The fungitoxic effect of sulphur on V. inaequalis was also confirmed in this study....

  20. Influência das variáveis biopsicossociais na qualidade de vida em asmáticos

    Directory of Open Access Journals (Sweden)

    Ana Paula Soares de Matos

    Full Text Available A asma brônquica é uma doença complexa e interfere com a qualidade de vida desses doentes. Pretendemos, com a presente investigação, estudar a relação das variáveis sócio-demográficas (género, idade e grau de instrução, clínicas (gravidade da doença, duração e tipo clínico e psicológicas (cognições, emoções e comportamentos com a qualidade de vida do doente asmático. Cinqüenta doentes asmáticos do Departamento de Pneumologia e Imunoalergologia dos Hospitais da Universidade de Coimbra preencheram cinco questionários de auto-resposta que avaliavam as variáveis psicológicas em estudo. Os dados clínicos relativamente à doença foram igualmente recolhidos.Os nossos resultados revelam-nos que a qualidade de vida se relaciona com um conjunto de variáveis que podemos denominar biopsicossociais (e.g., uma menor qualidade de vida relaciona-se com uma maior idade, menor escolaridade, uma atitude mais negativa face à asma, designada "estigma", cognições disfuncionais e comportamentos/emoções-problema relacionados com a asma. Implicações ao nível do tratamento são apresentadas.

  1. Intervención educativa para población infanto-juvenil asmática

    Directory of Open Access Journals (Sweden)

    Maria Antonia Acevedo Veja

    2015-11-01

    Full Text Available Se realizó una intervención educativa a la población infanto-juvenil asmática con edades entre ocho y once años en el policlínico de Manatí, Las Tunas, entre enero y julio de 2012, con el objetivo de evaluar la eficacia de la misma. La población de estudio estuvo formada por los 258 pacientes asmáticos de los 29 Consultorios de Médico de Familia (CMF del área, y la muestra por los 50 seleccionados por muestreo aleatorio simple. La información se obtuvo mediante un cuestionario que fue aplicado antes y después de la intervención educativa y los datos fueron recogidos durante la consulta y de la historia clínica individual. Se concluyó que predominó el sexo masculino, con antecedentes de primera línea de asma bronquial, con factores desencadenantes tales como: infecciones respiratorias agudas, polvo y humedad, así como aquellos que presentan signos clínicos de reflujo y que tienen una mala técnica de aplicación de spray. Se apreció un insuficiente nivel de conocimientos sobre la evaluación de severidad de la crisis, los factores desencadenantes, el manejo del spray y el tratamiento intercrisis, y las exacerbaciones.

  2. Non Destructive Test Dye Penetrant and Ultrasonic on Welding SMAW Butt Joint with Acceptance Criteria ASME Standard

    Science.gov (United States)

    Endramawan, T.; Sifa, A.

    2018-02-01

    The purpose of this research is to know the type of discontinuity of SMAW welding result and to determine acceptance criteria based on American Society of Mechanical Engineer (ASME) standard. Material used is mild steel 98,71% Fe and 0,212% C with hardness 230 VHN with specimen diameter 20 cm and thickness 1.2 cm which is welded use SMAW butt joint with electrode for rooting LB 52U diameter 2.6 mm, current 70 Ampere and voltage 380 volt, filler used LB 5218 electrode diameter 3.2 mm with current 80 Ampere and 380 volt. The method used to analyze the welded with non destructive test dye penetrant (PT) method to see indication on the surface of the object and Ultrasonic (UT) to see indication on the sub and inner the surface of the object, the result is discontinuity recorded and analyzed and then the discontinuity is determine acceptance criteria based on the American Society of Mechanical Engineer (ASME) standards. The result show the discontinuity of porosity on the surface of the welded and inclusion on sub material used ultrasonic test, all indication on dye penetrant or ultrasonic test if there were rejected of result of welded that there must be gouging on part which rejected and then re-welding.

  3. Automatic coding method of the ACR Code

    International Nuclear Information System (INIS)

    Park, Kwi Ae; Ihm, Jong Sool; Ahn, Woo Hyun; Baik, Seung Kook; Choi, Han Yong; Kim, Bong Gi

    1993-01-01

    The authors developed a computer program for automatic coding of ACR(American College of Radiology) code. The automatic coding of the ACR code is essential for computerization of the data in the department of radiology. This program was written in foxbase language and has been used for automatic coding of diagnosis in the Department of Radiology, Wallace Memorial Baptist since May 1992. The ACR dictionary files consisted of 11 files, one for the organ code and the others for the pathology code. The organ code was obtained by typing organ name or code number itself among the upper and lower level codes of the selected one that were simultaneous displayed on the screen. According to the first number of the selected organ code, the corresponding pathology code file was chosen automatically. By the similar fashion of organ code selection, the proper pathologic dode was obtained. An example of obtained ACR code is '131.3661'. This procedure was reproducible regardless of the number of fields of data. Because this program was written in 'User's Defined Function' from, decoding of the stored ACR code was achieved by this same program and incorporation of this program into program in to another data processing was possible. This program had merits of simple operation, accurate and detail coding, and easy adjustment for another program. Therefore, this program can be used for automation of routine work in the department of radiology

  4. Fundamentals of convolutional coding

    CERN Document Server

    Johannesson, Rolf

    2015-01-01

    Fundamentals of Convolutional Coding, Second Edition, regarded as a bible of convolutional coding brings you a clear and comprehensive discussion of the basic principles of this field * Two new chapters on low-density parity-check (LDPC) convolutional codes and iterative coding * Viterbi, BCJR, BEAST, list, and sequential decoding of convolutional codes * Distance properties of convolutional codes * Includes a downloadable solutions manual

  5. On-line monitoring and inservice inspection in codes; Betriebsueberwachung und wiederkehrende Pruefungen in den Regelwerken

    Energy Technology Data Exchange (ETDEWEB)

    Bartonicek, J.; Zaiss, W. [Gemeinschaftskernkraftwerk Neckar GmbH, Neckarwestheim (Germany); Bath, H.R. [Bundesamt fuer Strahlenschutz, Salzgitter (Germany). Geschaeftsstelle des Kerntechnischen Ausschusses (KTA)

    1999-08-01

    The relevant regulatory codes determine the ISI tasks and the time intervals for recurrent components testing for evaluation of operation-induced damaging or ageing in order to ensure component integrity on the basis of the last available quality data. In-service quality monitoring is carried out through on-line monitoring and recurrent testing. The requirements defined by the engineering codes elaborated by various institutions are comparable, with the KTA nuclear engineering and safety codes being the most complete provisions for quality evaluation and assurance after different, defined service periods. German conventional codes for assuring component integrity provide exclusively for recurrent inspection regimes (mainly pressure tests and optical testing). The requirements defined in the KTA codes however always demanded more specific inspections relying on recurrent testing as well as on-line monitoring. Foreign codes for ensuring component integrity concentrate on NDE tasks at regular time intervals, with time intervals scope of testing activities being defined on the basis of the ASME code, section XI. (orig./CB) [Deutsch] Fuer die Komponentenintegritaet sind die Schaedigungsmechanismen mit dem nach den Regelwerken einzuhaltenden Abstand abzusichern. Dabei ist die jeweils vorhandene (Ist-) Qualitaet als Ausgangspunkt entscheidend. Die Absicherung der vorhandenen Qualitaet im weiteren Betrieb erfolgt durch geeignete Betriebsueberwachung und wiederkehrende Pruefungen. Die Anforderungen der Regelwerke sind vergleichbar, wobei die Bestimmung der vorhandenen Qualitaet nach einer bestimmten Betriebszeit sowie deren Absicherung im weiteren Betrieb am vollstaendigsten auf Basis des KTA-Regelwerkes moeglich ist. Die Absicherung der Komponentenintegritaet im Betrieb beruht in deutschen konventionellen Regelwerken nur auf den wiederkehrenden Pruefungen (hauptsaechlich Druckpruefungen und Sichtpruefungen). Das KTA-Regelwerk forderte hier schon immer qualifizierte

  6. Structural diversity in gallium(III) complexes of the tripodal triarsine MeC(CH2AsMe2)3.

    Science.gov (United States)

    Cheng, Fei; Hector, Andrew L; Levason, William; Reid, Gillian; Webster, Michael; Zhang, Wenjian

    2007-06-07

    The preparation and crystal structures of the first examples of gallium halide complexes with the tripodal arsine, MeC(CH(2)AsMe(2))3, reveal three distinctly different coordination modes for the ligand; the neutral [{micro(3)-MeC(CH(2)AsMe(2))3-kappaAs:kappaAs':kappaAs''}(GaI(3))3] with the triarsine coordinating to three GaI(3) units, [{Me(2)AsCH(2)C(Me)(CH(2)AsMe(2))2-kappa(2)AsAs'}GaCl(2)][GaCl(4)] involving bidentate chelation to a GaCl2+ cationic unit with the third As donor atom uncoordinated, and [{MeC(CH(2)AsMe(2))3-kappaAs:kappa(2)As'As''}(GaCl3)(GaCl2)][GaCl4] in which the triarsine forms a bidentate chelate to the GaCl2+ unit and the third As donor atom binds to a further GaCl3 unit.

  7. Dynamic experiments with high bisphenol-A concentrations modelled with an ASM model extended to include a separate XOC degrading microorganism

    DEFF Research Database (Denmark)

    Lindblom, Erik Ulfson; Press-Kristensen, Kåre; Vanrolleghem, P.A.

    2009-01-01

    with the endocrine disrupting XOC bisphenol-A (BPA) in an activated sludge process with real wastewater were used to hypothesize an ASM-based process model including aerobic growth of a specific BPA-degrading microorganism and sorption of BPA to sludge. A parameter estimation method was developed, which...

  8. Comportamiento de variables clínico-epidemiológicas en pacientes asmáticos. Consultorio Médico de Familia 14, Puerto Padre

    Directory of Open Access Journals (Sweden)

    José Ramón Martínez Pérez

    2015-12-01

    Full Text Available Se realizó un estudio descriptivo de corte transversal en 40 pacientes asmáticos de todas las edades, pertenecientes al Consultorio 14 del área de salud de Puerto Padre, provincia de Las Tunas, durante los meses de enero a junio de 2008; con el objetivo de determinar el comportamiento de variables clínico-epidemiológicas en dichos pacientes. Para cumplimentar los objetivos se diseñó una encuesta que recogió las variables de interés. El análisis se hizo a través del sistema Statistix, permitiendo  obtener  la distribución de frecuencia y los porcientos. El test de Chi-Cuadrado se empleó en la comparación de variables cualitativas. Los resultados fueron descritos, interpretados y comparados con otros estudios. Se concluye que los pacientes grado I según Kraeppelin son los mas representados en nuestra población de pacientes asmáticos;  los broncodilatadores son los medicamentos mas utilizados por la población asmática estudiada; el incumplimiento del tratamiento medicamentoso no se relacionó con la severidad de la enfermedad en la población estudiada;  las malas condiciones de la vivienda y  el tabaquismo influyeron de forma negativa en la evolución del paciente asmático.

  9. Optimization of the Production of Sludge in an Activated Sludge System Through the Calibration of the ASM1 Model

    Directory of Open Access Journals (Sweden)

    Espinosa-Rodríguez M.A

    2015-01-01

    Full Text Available Recently several protocols have been proposed for the calibration the ASM1 model and each one of them emphasizes obtaining a good adjustment in the production of sludge. Precisely here is where the discrepancies are evaluated and adjustments made to data, through a mass balance. The objective of this work was to conduct first a balance of flows in the wastewater treatment plant "Dulces Nombres" in Monterrey, Nuevo Leon, Mexico, and then adjust them until closing properly the mass balance for the total phosphorus, total suspended solids, and inorganic suspended solids (ISS. On might say that to calibrate the biological model was important to determine reliably the flow of sludge (QWAS since on it depends the cell retention mean time (θC in the reactor; this was accomplished successfully through the balance of the ISS and using of GPS-X software for the simulation of scenarios of optimization.

  10. Aeração nasal em crianças asmáticas Nasal ventilation in asthmatics children

    Directory of Open Access Journals (Sweden)

    Daniele Andrade da Cunha

    2011-10-01

    Full Text Available OBJETIVO: identificar a presença de sinais de alterações na expiração de crianças asmáticas. MÉTODO: este estudo foi realizado com 30 crianças com idades entre 6 e 10 anos de ambos os sexos com diagnóstico clínico de asma confirmado pelo prontuário médico e 30 crianças não asmáticas também de ambos os sexos na mesma faixa etária. Foi avaliada a aeração nasal com o espelho milimetrado de Altmann, sendo mensurado o escape de ar nasal objetivando a verificação da saída uni ou bilateral do ar e a relação de simetria entre a narina direita e a esquerda. As imagens foram importadas para o computador por meio do scanner HP da série Scanjet 2400. A análise foi realizada no software Scion Image for Windows (Alpha 4.0.3.2. Para análise das variáveis quantitativas entre grupos foi aplicado o teste t-student e para a análise intragrupos foi aplicado o teste t-Student pareado.Todas as conclusões foram tomadas ao nível de significância de 5%, sendo usados o Excel 2000 e o SPSS v8.0, para as análises. RESULTADOS: não foram encontradas diferenças estatisticamente significantes entre as crianças asmáticas e não-ásmáticas, acerca das mensurações quanto à área total e quanto às áreas das narinas direita e esquerda. CONCLUSÃO: não foi identificada a presença de sinais de alterações na expiração de crianças asmáticas, desta forma, faz-se necessário um estudo mais específico das funções nasal e pulmonar.PURPOSE: to identify the symptoms of changes in the exhalation of asthmatic children. METHOD: this study was conducted with 30 children from 6 to 10 year-old, of both genders and with asthma clinical diagnosis confirmed by medical records and 30 non-asthmatic children from 6 to 10 year-old, of both genders, and with same age. We evaluated the nasal ventilation with Altmann millimeter nasal mirror measuring the nasal air escape in order to check their unilateral or bilateral air output and the relation of

  11. Structural integrity assessment of a pressure container component. Design and service code implementation. Case studies

    International Nuclear Information System (INIS)

    Sanzi, H.C.

    2006-01-01

    In the present work, the most important results of the local stresses occurred in the cracked pipes with a axial through-wall crack (outer), produced during operation of a Petrochemical Plant, using finite elements method, are presented. As requested, the component has been verified based 3D FE plastic analysis, under the postulated failure loading, assuring with this method a high degree of accuracy in the results. Codes used by Design and Service, as ASME Section VIII Div. 2 and API 579, have been used in the analysis. (author) [es

  12. Pengaruh pH, Kecepatan Putar dan Asam Asetat terhadap Karakteristik CO2 Corrosion Baja ASME SA516 grade 70

    Directory of Open Access Journals (Sweden)

    Faris Adham

    2017-01-01

    Full Text Available Fenomena korosi merupakan sesuatu yang pasti terjadi pada setiap logam. Laju korosi dari suatu material dipengaruhi oleh beberapa faktor diantaranya yaitu nilai pH lingkungan dan karakteristik aliran fluida yang kontak langsung dengan logam. Pada oil and gas industry, baja ASME SA 516 grade 70 sering digunakan sebagai material flowline dan banyak terjadi CO2 Corrosion. Penelitian ini bertujuan untuk melakukan studi laju korosi material baja ASME SA 516 grade 70 yang mengandung CO2. Penelitian dilakukan dengan metoda weight loss menggunakan alat Rotating Cylinder Electrode (RCE selama 10 hari dan metode Polarization selama 1 jam. Selain itu digunakan pula XRD dan SEM guna mendukung data-data analisa. Pada penelitian ini digunakan media elektrolit NaCl 3,5% dengan kandungan CH3COOH sebesar 0 ppm dan 1500 ppm dengan variasi kecepatan putaran yaitu 0 RPM, 150 RPM, 300 RPM, dan 450 RPM pada pH 5 dan 6. Pada pengujian polarization, didapatkan hasil laju korosi tertinggi sebesar 9.9323 mm/y pada larutan CH3COOH 1500 ppm pH 5 dan kecepatan putar 450 RPM, sedangkan data dari pengujian weight loss sebesar 4.8795 mm/y. Hasil pengamatan SEM menunjukkan adanya perbedaan morfologi pada permukaan spesimen karena pengaruh kecepatan putaran. Kecepatan putaran mengakibatkan tergerusnya produk korosi oleh aliran. Pada pengujian XRD dengan menggunakan spesimen pH 5 dengan kandungan 0 ppm dan 1500 ppm 0 RPM ditemukan FeCO3, Fe(OH3 dan senyawa FeOOH sebagai produk korosi.

  13. Design validation of the ITER EC upper launcher according to codes and standards

    Energy Technology Data Exchange (ETDEWEB)

    Spaeh, Peter, E-mail: peter.spaeh@kit.edu [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Aiello, Gaetano [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Gagliardi, Mario [Karlsruhe Institute of Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); F4E, Fusion for Energy, Joint Undertaking, Barcelona (Spain); Grossetti, Giovanni; Meier, Andreas; Scherer, Theo; Schreck, Sabine; Strauss, Dirk; Vaccaro, Alessandro [Karlsruhe Institute of Technology, Institute for Applied Materials, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany); Weinhorst, Bastian [Karlsruhe Institute of Technology, Institute for Neutron Physics and Reactor Technology, Association KIT-EURATOM, P.O. Box 3640, D-76021 Karlsruhe (Germany)

    2015-10-15

    Highlights: • A set of applicable codes and standards has been chosen for the ITER EC upper launcher. • For a particular component load combinations, failure modes and stress categorizations have been determined. • The design validation was performed in accordance with the “design by analysis”-approach of the ASME boiler and pressure vessel code section III. - Abstract: The ITER electron cyclotron (EC) upper launcher has passed the CDR (conceptual design review) in 2005 and the PDR (preliminary design review) in 2009 and is in its final design phase now. The final design will be elaborated by the European consortium ECHUL-CA with contributions from several research institutes in Germany, Italy, the Netherlands and Switzerland. Within this consortium KIT is responsible for the design of the structural components (the upper port plug, UPP) and also the design integration of the launcher. As the selection of applicable codes and standards was under discussion for the past decade, the conceptual and the preliminary design of the launcher structure were not elaborated in straight accordance with a particular code but with a variety of well-acknowledged engineering practices. For the final design it is compulsory to validate the design with respect to a typical engineering code in order to be compliant with the ITER quality and nuclear requirements and to get acceptance from the French regulator. This paper presents typical design validation of the closure plate, which is the vacuum and Tritium barrier and thus a safety relevant component of the upper port plug (UPP), performed with the ASME boiler and pressure vessel code. Rationales for choosing this code are given as well as a comparison between different design methods, like the “design by rule” and the “design by analysis” approach. Also the selections of proper load specifications and the identification of potential failure modes are covered. In addition to that stress categorizations, analyses

  14. Model Children's Code.

    Science.gov (United States)

    New Mexico Univ., Albuquerque. American Indian Law Center.

    The Model Children's Code was developed to provide a legally correct model code that American Indian tribes can use to enact children's codes that fulfill their legal, cultural and economic needs. Code sections cover the court system, jurisdiction, juvenile offender procedures, minor-in-need-of-care, and termination. Almost every Code section is…

  15. Affine Grassmann codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Beelen, Peter; Ghorpade, Sudhir Ramakant

    2010-01-01

    We consider a new class of linear codes, called affine Grassmann codes. These can be viewed as a variant of generalized Reed-Muller codes and are closely related to Grassmann codes.We determine the length, dimension, and the minimum distance of any affine Grassmann code. Moreover, we show that af...

  16. Doxofylline does not increase formoterol-induced cAMP nor MKP-1 expression in ASM cells resulting in lack of anti-inflammatory effect.

    Science.gov (United States)

    Patel, Brijeshkumar S; Kugel, Michael J; Baehring, Gina; Ammit, Alaina J

    2017-08-01

    The xanthine doxofylline has been examined in clinical trials and shown to have efficacy and greater tolerability than theophylline in asthma and chronic obstructive pulmonary disease. The 'novofylline' doxofylline has demonstrated bronchodilatory and anti-inflammatory actions in in vivo and ex vivo experimental models of respiratory disease. However, there are limited studies in vitro. We address this herein and examine whether doxofylline has anti-inflammatory impact on primary cultures of airway smooth muscle (ASM) cells. We conduct a series of investigations comparing and contrasting doxofylline with the archetypal xanthine, theophylline, and the specific phosphodiesterase (PDE) 4 inhibitor, cilomilast. We confirm that the xanthine drugs do not have action as PDE inhibitors in ASM cells. Unlike cilomilast, doxofylline (and theophylline) do not increase cAMP production in ASM cells induced by long-acting β 2 -agonist formoterol. Similar to theophylline, and consistent with the lack of cAMP potentiation, doxofylline does not augment formoterol-induced upregulation of the anti-inflammatory protein mitogen-activated protein kinase phosphatase 1 (MKP-1). However, when we examine the effect of doxofylline on secretion of the interleukin 8 from ASM cells stimulated by tumour necrosis factor (an in vitro surrogate measure of inflammation), there was no repression of inflammation. This is in contrast to the anti-inflammatory impact exerted by theophylline and cilomilast in confirmatory experiments. In summary, our study is the first to examine the effect of doxofylline on ASM cells in vitro and highlights some distinct differences between two key members of xanthine drug family, doxofylline and theophylline. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. TRAIL death receptor 4 signaling via lysosome fusion and membrane raft clustering in coronary arterial endothelial cells: evidence from ASM knockout mice.

    Science.gov (United States)

    Li, Xiang; Han, Wei-Qing; Boini, Krishna M; Xia, Min; Zhang, Yang; Li, Pin-Lan

    2013-01-01

    Tumor necrosis factor-related apoptosis-inducing ligand (TRAIL) and its receptor, death receptor 4 (DR4), have been implicated in the development of endothelial dysfunction and atherosclerosis. However, the signaling mechanism mediating DR4 activation leading to endothelial injury remains unclear. We recently demonstrated that ceramide production via hydrolysis of membrane sphingomyelin by acid sphingomyelinase (ASM) results in membrane raft (MR) clustering and the formation of important redox signaling platforms, which play a crucial role in amplifying redox signaling in endothelial cells leading to endothelial dysfunction. The present study aims to investigate whether TRAIL triggers MR clustering via lysosome fusion and ASM activation, thereby conducting transmembrane redox signaling and changing endothelial function. Using confocal microscopy, we found that TRAIL induced MR clustering and co-localized with DR4 in coronary arterial endothelial cells (CAECs) isolated from wild-type (Smpd1 (+/+)) mice. Furthermore, TRAIL triggered ASM translocation, ceramide production, and NADPH oxidase aggregation in MR clusters in Smpd1 ( +/+ ) CAECs, whereas these observations were not found in Smpd1 (-/-) CAECs. Moreover, ASM deficiency reduced TRAIL-induced O(2) (-[Symbol: see text]) production in CAECs and abolished TRAIL-induced impairment on endothelium-dependent vasodilation in small resistance arteries. By measuring fluorescence resonance energy transfer, we found that Lamp-1 (lysosome membrane marker protein) and ganglioside G(M1) (MR marker) were trafficking together in Smpd1 (+/+) CAECs, which was absent in Smpd1 (-/-) CAECs. Consistently, fluorescence imaging of living cells with specific lysosome probes demonstrated that TRAIL-induced lysosome fusion with membrane was also absent in Smpd1 (-/-) CAECs. Taken together, these results suggest that ASM is essential for TRAIL-induced lysosomal trafficking, membrane fusion and formation of MR redox signaling platforms

  18. Generalized concatenated quantum codes

    International Nuclear Information System (INIS)

    Grassl, Markus; Shor, Peter; Smith, Graeme; Smolin, John; Zeng Bei

    2009-01-01

    We discuss the concept of generalized concatenated quantum codes. This generalized concatenation method provides a systematical way for constructing good quantum codes, both stabilizer codes and nonadditive codes. Using this method, we construct families of single-error-correcting nonadditive quantum codes, in both binary and nonbinary cases, which not only outperform any stabilizer codes for finite block length but also asymptotically meet the quantum Hamming bound for large block length.

  19. Rateless feedback codes

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Koike-Akino, Toshiaki; Orlik, Philip

    2012-01-01

    This paper proposes a concept called rateless feedback coding. We redesign the existing LT and Raptor codes, by introducing new degree distributions for the case when a few feedback opportunities are available. We show that incorporating feedback to LT codes can significantly decrease both...... the coding overhead and the encoding/decoding complexity. Moreover, we show that, at the price of a slight increase in the coding overhead, linear complexity is achieved with Raptor feedback coding....

  20. Current Status of the Elevated Temperature Structure Design Codes for VHTR

    International Nuclear Information System (INIS)

    Kim, Jong-Bum; Kim, Seok-Hoon; Park, Keun-Bae; Lee, Won-Jae

    2006-01-01

    An elevated temperature structure design and analysis is one of the key issues in the VHTR (Very High Temperature Reactor) project to achieve an economic production of hydrogen which will be an essential energy source for the near future. Since the operating temperature of a VHTR is above 850 .deg. C, the existing code and standards are insufficient for a high temperature structure design. Thus the issues concerning a material selection and behaviors are being studied for the main structural components of a VHTR in leading countries such as US, France, UK, and Japan. In this study, the current status of the ASME code, French RCC-MR, UK R5, and Japanese code were investigated and the necessary R and D items were discussed

  1. Coding for dummies

    CERN Document Server

    Abraham, Nikhil

    2015-01-01

    Hands-on exercises help you learn to code like a pro No coding experience is required for Coding For Dummies,your one-stop guide to building a foundation of knowledge inwriting computer code for web, application, and softwaredevelopment. It doesn't matter if you've dabbled in coding or neverwritten a line of code, this book guides you through the basics.Using foundational web development languages like HTML, CSS, andJavaScript, it explains in plain English how coding works and whyit's needed. Online exercises developed by Codecademy, a leading online codetraining site, help hone coding skill

  2. Advanced video coding systems

    CERN Document Server

    Gao, Wen

    2015-01-01

    This comprehensive and accessible text/reference presents an overview of the state of the art in video coding technology. Specifically, the book introduces the tools of the AVS2 standard, describing how AVS2 can help to achieve a significant improvement in coding efficiency for future video networks and applications by incorporating smarter coding tools such as scene video coding. Topics and features: introduces the basic concepts in video coding, and presents a short history of video coding technology and standards; reviews the coding framework, main coding tools, and syntax structure of AV

  3. Proceedings of the 4th NRC/ASME symposium on valve and pump testing

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-08-01

    The 1996 Symposium on Valve and Pump Testing, jointly sponsored by the Board on Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the U.S. Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. Individual papers of this Proceedings have been cataloged separately.

  4. Proceedings of the 4th NRC/ASME symposium on valve and pump testing

    International Nuclear Information System (INIS)

    1996-01-01

    The 1996 Symposium on Valve and Pump Testing, jointly sponsored by the Board on Nuclear Codes and Standards of the American Society of Mechanical Engineers and by the U.S. Nuclear Regulatory Commission, provides a forum for the discussion of current programs and methods for inservice testing and motor-operated valve testing at nuclear power plants. The symposium also provides an opportunity to discuss the need to improve that testing in order to help ensure the reliable performance of pumps and valves. The participation of industry representatives, regulators, and consultants results in the discussion of a broad spectrum of ideas and perspectives regarding the improvement of inservice testing of pumps and valves at nuclear power plants. Individual papers of this Proceedings have been cataloged separately

  5. Utilização de Ecolife® e Acibenzolar-s-metil (ASM no controle da antracnose da banana em pós-colheita Use of Ecolife® and Acibenzolar-S-metil (ASM on the control of antracnosis in banana post-harvest

    Directory of Open Access Journals (Sweden)

    Luciano Marinho Furtado

    2010-09-01

    Full Text Available O objetivo deste trabalho foi avaliar a ação dos produtos ASM e Ecolife no controle da antracnose pós-colheita em frutos de banana. Frutos sadios de banana, variedades maçã, prata, pacovan e cacau , em fase intermediária de maturação, foram imersos previamente em soluções de ASM e Ecolife e inoculados com Colletotrichum musae. Utilizou-se o delineamento inteiramente casualizado, em esquema fatorial com quatro repetições. Os resultados apresentados demonstraram a eficácia dos produtos nas concentrações de 5 ml/ L (Ecolife e 0,50g/ L (ASM no controle da antracnose nas variedades analisa das. A variedade cacau apresentou menor lesão quando tratada com o Ecolife (5,79 mm. Com relação ao efeito do ASM, a bana na prata demonstrou um melhor resultado, com tamanho médio de lesão de 5,62 mm. Com o decorrer do processo de maturação dos frutos houve um decréscimo na severidade da doença nas quatro variedades estudadas, exceto no tratamento testemunha, que continuou apresentando aumento no tamanho das lesões nos frutos e atingir a polpa ao final da maturação.The aim of this work was to evaluate the effects of ASM and Ecolife on the control of post-harvest antracnosis in banana. Banana fruits of Maçã, Prata, Pacovan and Figo varieties, at intermediate stage of maturation, were immersed in solutions of ASM and Ecolife and inoculated with Colletotrichum musae A completely randomized design was used, at a factorial scheme 4x2 (four varieties x two products with four replicates. The presented results demonstrated the susceptibility of the fruits to the disease, mainly Maça variety with lesion of 17,99 mm. It was demosntrated the effectiveness of products at concentrations of 5ml. L-1 (Ecolife and 0.50g. L-1 (ASM on antracnosis control. The Figo variety presented the smallest injuries when treated with Ecolife (5.79 mm. Regarding ASM effects, Prata variety demonstrated the best performance, with 5.62 mm of injuries diameter

  6. Application of the French Codes to the Pressurized Thermal Shocks Assessment

    Directory of Open Access Journals (Sweden)

    Mingya Chen

    2016-12-01

    Full Text Available The integrity of a reactor pressure vessel (RPV related to pressurized thermal shocks (PTSs has been extensively studied. This paper introduces an integrity assessment of an RPV subjected to a PTS transient based on the French codes. In the USA, the “screening criterion” for maximum allowable embrittlement of RPV material is developed based on the probabilistic fracture mechanics. However, in the French RCC-M and RSE-M codes, which are developed based on the deterministic fracture mechanics, there is no “screening criterion”. In this paper, the methodology in the RCC-M and RSE-M codes, which are used for PTS analysis, are firstly discussed. The bases of the French codes are compared with ASME and FAVOR codes. A case study is also presented. The results show that the method in the RCC-M code that accounts for the influence of cladding on the stress intensity factor (SIF may be nonconservative. The SIF almost doubles if the weld residual stress is considered. The approaches included in the codes differ in many aspects, which may result in significant differences in the assessment results. Therefore, homogenization of the codes in the long time operation of nuclear power plants is needed.

  7. Application of the French codes to the pressurized thermal shocks assessment

    International Nuclear Information System (INIS)

    Chen, Mingya; Wang, Rong Shan; Yu, Weiwei; Lu, Feng; Zhang, Guo Dong; Xue, Fei; Chen, Zhilin; Qian, Guian; Shi, Jinhua

    2016-01-01

    The integrity of a reactor pressure vessel (RPV) related to pressurized thermal shocks (PTSs) has been extensively studied. This paper introduces an integrity assessment of an RPV subjected to a PTS transient based on the French codes. In the USA, the 'screening criterion' for maximum allowable embrittlement of RPV material is developed based on the probabilistic fracture mechanics. However, in the French RCC-M and RSE-M codes, which are developed based on the deterministic fracture mechanics, there is no 'screening criterion'. In this paper, the methodology in the RCC-M and RSE-M codes, which are used for PTS analysis, are firstly discussed. The bases of the French codes are compared with ASME and FAVOR codes. A case study is also presented. The results show that the method in the RCC-M code that accounts for the influence of cladding on the stress intensity factor (SIF) may be nonconservative. The SIF almost doubles if the weld residual stress is considered. The approaches included in the codes differ in many aspects, which may result in significant differences in the assessment results. Therefore, homogenization of the codes in the long time operation of nuclear power plants is needed

  8. Locally orderless registration code

    DEFF Research Database (Denmark)

    2012-01-01

    This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows.......This is code for the TPAMI paper "Locally Orderless Registration". The code requires intel threadding building blocks installed and is provided for 64 bit on mac, linux and windows....

  9. Error Correcting Codes

    Indian Academy of Sciences (India)

    sound quality is, in essence, obtained by accurate waveform coding and decoding of the audio signals. In addition, the coded audio information is protected against disc errors by the use of a Cross Interleaved Reed-Solomon Code (CIRC). Reed-. Solomon codes were discovered by Irving Reed and Gus Solomon in 1960.

  10. An activated sludge modeling framework for xenobiotic trace chemicals (ASM-X): assessment of diclofenac and carbamazepine.

    Science.gov (United States)

    Plósz, Benedek Gy; Langford, Katherine H; Thomas, Kevin V

    2012-11-01

    Conventional models for predicting the fate of xenobiotic organic trace chemicals, identified, and calibrated using data obtained in batch experiments spiked with reference substances, can be limited in predicting xenobiotic removal in wastewater treatment plants (WWTPs). At stake is the level of model complexity required to adequately describe a general theory of xenobiotic removal in WWTPs. In this article, we assess the factors that influence the removal of diclofenac and carbamazepine in activated sludge, and evaluate the complexity required for the model to effectively predict their removal. The results are generalized to previously published cases. Batch experimental results, obtained under anoxic and aerobic conditions, were used to identify extensions to, and to estimate parameter values of the activated sludge modeling framework for Xenobiotic trace chemicals (ASM-X). Measurement and simulation results obtained in the batch experiments, spiked with the diclofenac and carbamazepine content of preclarified municipal wastewater shows comparably high biotransformation rates in the presence of growth substrates. Forward dynamic simulations were performed using full-scale data obtained from Bekkelaget WWTP (Oslo, Norway) to evaluate the model and to estimate the level of re-transformable xenobiotics present in the influent. The results obtained in this study demonstrate that xenobiotic loading conditions can significantly influence the removal capacity of WWTPs. We show that the trace chemical retransformation in upstream sewer pipes can introduce considerable error in assessing the removal efficiency of a WWTP, based only on parent compound concentration measurements. The combination of our data with those from the literature shows that solids retention time (SRT) can enhance the biotransformation of diclofenac, which was not the case for carbamazepine. Model approximation of the xenobiotic concentration, detected in the solid phase, suggest that between

  11. Rehabilitación integral y tolerancia al ejercicio físico en escolares asmáticos severos

    Directory of Open Access Journals (Sweden)

    . Héctor Alejandro Cruz Oliver

    1995-04-01

    Full Text Available Se realizó un estudio en 99 escolares asmáticos severos, incluidos en un programa de rehabilitación integral en el centro para niños asmáticos de la Ciudad de los Pioneros "José Martí" en Tarará, durante el curso escolar 1991-1992. A todos los escolares se les sometió antes de comenzar el programa, a una prueba de tolerancia al ejercicio físico mediante la carrera libre, y acorde con los resultados de ésta se clasificaron en 2 grupos; grupo I, con asma inducida por el ejercicio (AIE y grupo II, sin AIE. Al finalizar el programa de rehabilitación al grupo I se le sometió nuevamente a la prueba de tolerancia al ejercicio físico. Todos los escolares se evaluaron mediante la espirometría en condiciones basales antes del programa de rehabilitación y al finalizar éste. En 55 escolares (55,5 % se constató la presencia inicial de AIE. Al finalizar el programa de rehabilitación sólo en 23 de ellos se mantuvo este fenómeno. Con excepción de un escolar perteneciente al grupo I el resto de los niños toleraron sin dificultad las actividades físicas programadas. En relación con los parámetros de función respiratoria no se hallaron diferencias significativas en ninguno de ellos, cuando se compararon ambos grupos entre sí antes del programa de rehabilitación, y después de él. Comparando cada grupo consigo mismo sólo se observó un incremento significativo del flujo máximo medio (MMF en ambos grupos, lo que reflejó una disminución del componente obstructivo bronquial periférico.

  12. Investigation of the Stress Intensity Limits of ASME Section III Div.5 for Structure Design Criteria of SFR Fuel Assembly

    Energy Technology Data Exchange (ETDEWEB)

    Choo, Jin-Yup; Kim, Hyung-Kyu; Cheon, Jin-Sik [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-10-15

    These affect the mechanical design of the fuel assembly components. And thus, appropriate structural design criteria should also be chosen to incorporate the specific design conditions of the SFR fuel assemblies. Among them, the temperature is one of the most crucial conditions to be concerned because the sodium coolant temperature is normally more than 500ºC which is much higher than that of the LWR (< 350ºC). This implies that a thermal creep should be significantly considered in the SFR fuel assembly mechanical design. In addition to the high temperature condition, an irradiation swelling is also an important behavior that the SFR fuel assembly material should accommodate. To incorporate the temperature and irradiation impacts, the material of the fuel assembly components is presently determined to be made of HT-9, the ferriticmartensitic steel. In this paper, the ASME Sec. III Div. 5 (referred to as ‘Div. 5’ hereinafter), which was developed for a ‘high temperature reactor’, is considered as one of the structural design criteria for the mechanical design of SFR fuel assemblies. In this paper, the stress intensity limits, S{sub m} and S{sub t} of HT-9 were built for the structural criteria of an SFR fuel assembly. S{sub m} is obtained from the ultimate strength. As for S{sub t}, it is more complicated because of its dependency of time duration in addition to temperature. Following the definition of S{sub mt}, the method in the ASME Sec. III Div. 1, Subsec. NH was consulted. We found that the Sm is adopted as S{sub mt} under the temperature about 470ºC which is relatively low temperature range and over 470ºC with relatively short time duration as 1000 hours. And the S{sub t} is adopted as Smt at over 470ºC and long time duration over 34800 hours, and over 520ºC and 10{sup 4} hours too. And at over 570ºC and 1000 hours, and at over 630ºC and 100 hours, S{sub t} is also adopted for S{sub mt}.

  13. Network Coding Taxonomy

    OpenAIRE

    Adamson , Brian; Adjih , Cédric; Bilbao , Josu; Firoiu , Victor; Fitzek , Frank; Samah , Ghanem ,; Lochin , Emmanuel; Masucci , Antonia; Montpetit , Marie-Jose; Pedersen , Morten V.; Peralta , Goiuri; Roca , Vincent; Paresh , Saxena; Sivakumar , Senthil

    2017-01-01

    Internet Research Task Force - Working document of the Network Coding Research Group (NWCRG), draft-irtf-nwcrg-network-coding-taxonomy-05 (work in progress), https://datatracker.ietf.org/doc/draft-irtf-nwcrg-network-coding-taxonomy/; This document summarizes a recommended terminology for Network Coding concepts and constructs. It provides a comprehensive set of terms with unique names in order to avoid ambiguities in future Network Coding IRTF and IETF documents. This document is intended to ...

  14. QR Codes 101

    Science.gov (United States)

    Crompton, Helen; LaFrance, Jason; van 't Hooft, Mark

    2012-01-01

    A QR (quick-response) code is a two-dimensional scannable code, similar in function to a traditional bar code that one might find on a product at the supermarket. The main difference between the two is that, while a traditional bar code can hold a maximum of only 20 digits, a QR code can hold up to 7,089 characters, so it can contain much more…

  15. Pressure vessels design methods using the codes, fracture mechanics and multiaxial fatigue

    Directory of Open Access Journals (Sweden)

    Fatima Majid

    2016-10-01

    Full Text Available This paper gives a highlight about pressure vessel (PV methods of design to initiate new engineers and new researchers to understand the basics and to have a summary about the knowhow of PV design. This understanding will contribute to enhance their knowledge in the selection of the appropriate method. There are several types of tanks distinguished by the operating pressure, temperature and the safety system to predict. The selection of one or the other of these tanks depends on environmental regulations, the geographic location and the used materials. The design theory of PVs is very detailed in various codes and standards API, such as ASME, CODAP ... as well as the standards of material selection such as EN 10025 or EN 10028. While designing a PV, we must design the fatigue of its material through the different methods and theories, we can find in the literature, and specific codes. In this work, a focus on the fatigue lifetime calculation through fracture mechanics theory and the different methods found in the ASME VIII DIV 2, the API 579-1 and EN 13445-3, Annex B, will be detailed by giving a comparison between these methods. In many articles in the literature the uniaxial fatigue has been very detailed. Meanwhile, the multiaxial effect has not been considered as it must be. In this paper we will lead a discussion about the biaxial fatigue due to cyclic pressure in thick-walled PV. Besides, an overview of multiaxial fatigue in PVs is detailed

  16. Efficient Coding of Information: Huffman Coding -RE ...

    Indian Academy of Sciences (India)

    1. Introduction. Shannon's landmark paper 'A Mathematical Theory of. Communication' [1] laid the foundation for communica- ... coding theory, codes over graphs and iterative techniques, and informa- tion theory. .... An important consequence of independence is that if. {Xb X2 , . Xn} are independent random variables, each.

  17. Turbo Codes Extended with Outer BCH Code

    DEFF Research Database (Denmark)

    Andersen, Jakob Dahl

    1996-01-01

    The "error floor" observed in several simulations with the turbo codes is verified by calculation of an upper bound to the bit error rate for the ensemble of all interleavers. Also an easy way to calculate the weight enumerator used in this bound is presented. An extended coding scheme is proposed...

  18. instU_3d_asm_Cp: MERRA 3D IAU State, Meteorology Diurnal 1.25 x 1.25 degree V5.2.0 (MAIUCPASM) at GES DISC

    Data.gov (United States)

    National Aeronautics and Space Administration — The MAIUCPASM or instU_3d_asm_Cp data product is the MERRA Data Assimilation System 3-Dimensional assimilated state on pressure, at a reduced resolution. It is a...

  19. inst3_3d_asm_Cp: MERRA 3D IAU State, Meteorology Instantaneous 3-hourly 1.25 x 1.25 degree V5.2.0 (MAI3CPASM) at GES DISC

    Data.gov (United States)

    National Aeronautics and Space Administration — The MAI3CPASM or inst3_3d_asm_Cp data product is the MERRA Data Assimilation System 3-Dimensional assimilated state on pressure, at a reduced resolution. It is a...

  20. instM_3d_asm_Cp: MERRA 3D IAU State, Meteorology Monthly Mean 1.25 x 1.25 degree V5.2.0 (MAIMCPASM) at GES DISC

    Data.gov (United States)

    National Aeronautics and Space Administration — The MAIMCPASM or instM_3d_asm_Cp data product is the MERRA Data Assimilation System 3-Dimensional assimilated state on pressure, at a reduced resolution. It is a...

  1. 9 July 2012 - Academy of Sciences Malaysia (ASM), Chairman, Mathematical and Physical Sciences Discipline Group M. Yahaya FASc and his delegation visiting the LHC superconducting magnet test hall with Technology Department G. De Rijk.

    CERN Document Server

    Maximilien Brice

    2012-01-01

    9 July 2012 - Academy of Sciences Malaysia (ASM), Chairman, Mathematical and Physical Sciences Discipline Group M. Yahaya FASc and his delegation visiting the LHC superconducting magnet test hall with Technology Department G. De Rijk.

  2. const_2d_asm_Nx: MERRA DAS 2d constants 0.667 x 0.5 degree V5.2.0 (MAC0NXASM) at GES DISC

    Data.gov (United States)

    National Aeronautics and Space Administration — The MAC0NXASM or const_2d_asm_Nx data product is the MERRA Data Assimilation System 2-Dimensional Constants at native resolution. MERRA, or the Modern Era...

  3. Effect of beta2-adrenoceptor agonists and other cAMP-elevating agents on inflammatory gene expression in human ASM cells: a role for protein kinase A.

    Science.gov (United States)

    Kaur, Manminder; Holden, Neil S; Wilson, Sylvia M; Sukkar, Maria B; Chung, Kian Fan; Barnes, Peter J; Newton, Robert; Giembycz, Mark A

    2008-09-01

    In diseases such as asthma, airway smooth muscle (ASM) cells play a synthetic role by secreting inflammatory mediators such as granulocyte-macrophage colony-stimulating factor (GM-CSF), IL-6, or IL-8 and by expressing surface adhesion molecules, including ICAM-1. In the present study, PGE(2), forskolin, and short-acting (salbutamol) and long-acting (salmeterol and formoterol) beta(2)-adrenoceptor agonists reduced the expression of ICAM-1 and the release of GM-CSF evoked by IL-1beta in ASM cells. IL-1beta-induced IL-8 release was also repressed by PGE(2) and forskolin, whereas the beta(2)-adrenoceptor agonists were ineffective. In each case, repression of these inflammatory indexes was prevented by adenoviral overexpression of PKIalpha, a highly selective PKA inhibitor. These data indicate a PKA-dependent mechanism of repression and suggest that agents that elevate intracellular cAMP, and thereby activate PKA, may have a widespread anti-inflammatory effect in ASM cells. Since ICAM-1 and GM-CSF are highly NF-kappaB-dependent genes, we used an adenoviral-delivered NF-kappaB-dependent luciferase reporter to examine the effects of forskolin and the beta(2)-adrenoceptor agonists on NF-kappaB activation. There was no effect on luciferase activity measured in the presence of forskolin or beta(2)-adrenoceptor agonists. This finding is consistent with the observation that IL-1beta-induced expression of IL-6, a known NF-kappaB-dependent gene in ASM, was also unaffected by beta(2)-adrenoceptor agonists, forskolin, PGE(2), 8-bromo-cAMP, or rolipram. Collectively, these results indicate that repression of IL-1beta-induced ICAM-1 expression and GM-CSF release by cAMP-elevating agents, including beta(2)-adrenoceptor agonists, may not occur through a generic effect on NF-kappaB.

  4. Granulomatose broncocêntrica idiopática em jovem não asmática

    Directory of Open Access Journals (Sweden)

    Santos José Wellington Alves dos

    2003-01-01

    Full Text Available Granulomatose broncocêntrica é um achado histopatológico descritivo, caracterizado pela inflamação granulomatosa necrosante, centrada em brônquios e bronquíolos, e que ocorre associada a doenças infecciosas, imunológicas e neoplásicas, ou de forma idiopática. Este trabalho relata o caso de uma jovem não asmática de 26 anos com dor torácica, febre e tosse produtiva havia um mês, que apresentou consolidação e cavitação em segmento lingular, observadas na radiografia e na tomografia computadorizada de tórax. Punção aspirativa transbrônquica evidenciou lesão inflamatória inespecífica, sem etiologia identificada. O exame histológico de material obtido por biópsia pulmonar a céu aberto foi compatível com granulomatose broncocêntrica idiopática. Após tratamento com prednisona, houve melhora clínica, sem recidivas.

  5. Optimization of A(2)O BNR processes using ASM and EAWAG Bio-P models: model performance.

    Science.gov (United States)

    El Shorbagy, Walid E; Radif, Nawras N; Droste, Ronald L

    2013-12-01

    This paper presents the performance of an optimization model for a biological nutrient removal (BNR) system using the anaerobic-anoxic-oxic (A(2)O) process. The formulated model simulates removal of organics, nitrogen, and phosphorus using a reduced International Water Association (IWA) Activated Sludge Model #3 (ASM3) model and a Swiss Federal Institute for Environmental Science and Technology (EAWAG) Bio-P module. Optimal sizing is attained considering capital and operational costs. Process performance is evaluated against the effect of influent conditions, effluent limits, and selected parameters of various optimal solutions with the following results: an increase of influent temperature from 10 degrees C to 25 degrees C decreases the annual cost by about 8.5%, an increase of influent flow from 500 to 2500 m(3)/h triples the annual cost, the A(2)O BNR system is more sensitive to variations in influent ammonia than phosphorus concentration and the maximum growth rate of autotrophic biomass was the most sensitive kinetic parameter in the optimization model.

  6. Modeling nitrous oxide production during biological nitrogen removal via nitrification and denitrification: extensions to the general ASM models.

    Science.gov (United States)

    Ni, Bing-Jie; Ruscalleda, Maël; Pellicer-Nàcher, Carles; Smets, Barth F

    2011-09-15

    Nitrous oxide (N(2)O) can be formed during biological nitrogen (N) removal processes. In this work, a mathematical model is developed that describes N(2)O production and consumption during activated sludge nitrification and denitrification. The well-known ASM process models are extended to capture N(2)O dynamics during both nitrification and denitrification in biological N removal. Six additional processes and three additional reactants, all involved in known biochemical reactions, have been added. The validity and applicability of the model is demonstrated by comparing simulations with experimental data on N(2)O production from four different mixed culture nitrification and denitrification reactor study reports. Modeling results confirm that hydroxylamine oxidation by ammonium oxidizers (AOB) occurs 10 times slower when NO(2)(-) participates as final electron acceptor compared to the oxic pathway. Among the four denitrification steps, the last one (N(2)O reduction to N(2)) seems to be inhibited first when O(2) is present. Overall, N(2)O production can account for 0.1-25% of the consumed N in different nitrification and denitrification systems, which can be well simulated by the proposed model. In conclusion, we provide a modeling structure, which adequately captures N(2)O dynamics in autotrophic nitrification and heterotrophic denitrification driven biological N removal processes and which can form the basis for ongoing refinements.

  7. A Retrospective Look at 20 Years of ASM Education Programs (1990-2010) and a Prospective Look at the Next 20 Years (2011-2030).

    Science.gov (United States)

    Chang, Amy

    2011-01-01

    Professional societies provide visibility and legitimacy to the work of their post secondary educator members, advocate best practices in courses and sponsored student research, and establish deep networks and communities that catalyze members to collectively engage in undergraduate teaching and learning scholarship. Within the American Society for Microbiology (ASM), the Education Board, established in the mid-1970s, assumes this role. I have been fortunate enough to watch several pivotal programs support our growth and change the status quo by providing opportunities for biology educators to flourish. In this retrospective review, the background and details I offer about each initiative help explain ASM Education offerings, how our growth has been supported and how the status quo has changed. In this prospective look, I offer my vision of the future in post secondary education where classroom learning is student-centered and focused on global problems affecting our health and environment. For the profession to proliferate, the ASM must provide members as many opportunities in learning biology as they do with advancing biology to new frontiers.

  8. DFT study of isomers of the ruthenium dihydride complex RuH2(CO)2(AsMe2Ph)2.

    Science.gov (United States)

    Said, R Ben; Essalah, K; Sanhoury, M A K; Hussein, K; Boughdiri, S; Chermette, H

    2017-04-01

    A density functional theory (DFT) study of cct-As, ccc, and cct-CO isomers of the ruthenium dihydride complex RuH 2 (CO) 2 (AsMe 2 Ph) 2 is reported (see Scheme for the labeling isomer 34 structures of RuH 2 (CO) 2 (AsMe 2 Ph) 2 ). Complex geometries and relative energies of different isomers have been calculated with both B3LYP and M06-2X functionals. The results show that the B3LYP calculated Boltzmann populations of cct-As, ccc, and cct-CO isomers are 65.5, 34.2, and 0.3%, respectively. These are in better agreement with the experimental data than those calculated at the M06-2X level. However, the calculations of 1 H NMR chemical shifts were found to be better described with M06-2X than with B3LYP or with HF level of theories. In addition, a transition state between the two most stable isomers was determined through DFT/(B3LYP or M06-2X) calculations. Graphical Abstract Scheme: Labeling structure of RuH 2 (CO) 2 (AsMe 2 Ph) 2 .

  9. SEVERO code - user's manual

    International Nuclear Information System (INIS)

    Sacramento, A.M. do.

    1989-01-01

    This user's manual contains all the necessary information concerning the use of SEVERO code. This computer code is related to the statistics of extremes = extreme winds, extreme precipitation and flooding hazard risk analysis. (A.C.A.S.)

  10. Model and code development

    International Nuclear Information System (INIS)

    Anon.

    1977-01-01

    Progress in model and code development for reactor physics calculations is summarized. The codes included CINDER-10, PHROG, RAFFLE GAPP, DCFMR, RELAP/4, PARET, and KENO. Kinetics models for the PBF were developed

  11. Coding for optical channels

    CERN Document Server

    Djordjevic, Ivan; Vasic, Bane

    2010-01-01

    This unique book provides a coherent and comprehensive introduction to the fundamentals of optical communications, signal processing and coding for optical channels. It is the first to integrate the fundamentals of coding theory and optical communication.

  12. Enhancing QR Code Security

    OpenAIRE

    Zhang, Linfan; Zheng, Shuang

    2015-01-01

    Quick Response code opens possibility to convey data in a unique way yet insufficient prevention and protection might lead into QR code being exploited on behalf of attackers. This thesis starts by presenting a general introduction of background and stating two problems regarding QR code security, which followed by a comprehensive research on both QR code itself and related issues. From the research a solution taking advantages of cloud and cryptography together with an implementation come af...

  13. Stylize Aesthetic QR Code

    OpenAIRE

    Xu, Mingliang; Su, Hao; Li, Yafei; Li, Xi; Liao, Jing; Niu, Jianwei; Lv, Pei; Zhou, Bing

    2018-01-01

    With the continued proliferation of smart mobile devices, Quick Response (QR) code has become one of the most-used types of two-dimensional code in the world. Aiming at beautifying the appearance of QR codes, existing works have developed a series of techniques to make the QR code more visual-pleasant. However, these works still leave much to be desired, such as visual diversity, aesthetic quality, flexibility, universal property, and robustness. To address these issues, in this paper, we pro...

  14. ARC Code TI: CODE Software Framework

    Data.gov (United States)

    National Aeronautics and Space Administration — CODE is a software framework for control and observation in distributed environments. The basic functionality of the framework allows a user to observe a distributed...

  15. ARC Code TI: ROC Curve Code Augmentation

    Data.gov (United States)

    National Aeronautics and Space Administration — ROC (Receiver Operating Characteristic) curve Code Augmentation was written by Rodney Martin and John Stutz at NASA Ames Research Center and is a modification of ROC...

  16. Refactoring test code

    NARCIS (Netherlands)

    A. van Deursen (Arie); L.M.F. Moonen (Leon); A. van den Bergh; G. Kok

    2001-01-01

    textabstractTwo key aspects of extreme programming (XP) are unit testing and merciless refactoring. Given the fact that the ideal test code / production code ratio approaches 1:1, it is not surprising that unit tests are being refactored. We found that refactoring test code is different from

  17. Error Correcting Codes -34 ...

    Indian Academy of Sciences (India)

    the reading of data from memory the receiving process. Protecting data in computer memories was one of the earliest applications of Hamming codes. We now describe the clever scheme invented by Hamming in 1948. To keep things simple, we describe the binary length 7 Hamming code. Encoding in the Hamming Code.

  18. Morse Code Activity Packet.

    Science.gov (United States)

    Clinton, Janeen S.

    This activity packet offers simple directions for setting up a Morse Code system appropriate to interfacing with any of several personal computer systems. Worksheets are also included to facilitate teaching Morse Code to persons with visual or other disabilities including blindness, as it is argued that the code is best learned auditorily. (PB)

  19. Software Certification - Coding, Code, and Coders

    Science.gov (United States)

    Havelund, Klaus; Holzmann, Gerard J.

    2011-01-01

    We describe a certification approach for software development that has been adopted at our organization. JPL develops robotic spacecraft for the exploration of the solar system. The flight software that controls these spacecraft is considered to be mission critical. We argue that the goal of a software certification process cannot be the development of "perfect" software, i.e., software that can be formally proven to be correct under all imaginable and unimaginable circumstances. More realistically, the goal is to guarantee a software development process that is conducted by knowledgeable engineers, who follow generally accepted procedures to control known risks, while meeting agreed upon standards of workmanship. We target three specific issues that must be addressed in such a certification procedure: the coding process, the code that is developed, and the skills of the coders. The coding process is driven by standards (e.g., a coding standard) and tools. The code is mechanically checked against the standard with the help of state-of-the-art static source code analyzers. The coders, finally, are certified in on-site training courses that include formal exams.

  20. Calidad de vida en el adolescente asmático Quality of life in the asthmatic adolescent

    Directory of Open Access Journals (Sweden)

    Orquídea Aguirre Pérez

    2010-12-01

    Full Text Available INTRODUCCIÓN: la mejoría de la calidad de vida es clave en el tratamiento del niño-adolescente con asma. OBJETIVO: identificar la afectación que provoca el asma bronquial en la calidad de vida del adolescente asmático. MÉTODOS: se realizó un estudio descriptivo, longitudinal y prospectivo de 103 adolescentes asmáticos con diagnóstico de asma leve intermitente, asma leve persistente y asma moderada persistente en la Escuela Secundaria Básica "Antonio José de Sucre", en la localidad de Cojímar, en el período entre el 1ro. de enero de 2006 y el 31 de diciembre del propio año. RESULTADOS: los síntomas principales fueron la tos, la disnea y la sibilancia, y las molestias más frecuentes, el cansancio, la dificultad para respirar hondo y la sensación de quedar sin aire. Predominó el sexo masculino y las edades de 12 y 13 años. El mayor número de respuestas de las alteraciones de la función emocional se concentraba en las categorías más bajas del nivel de afectación, y las respuestas sobre la limitación de la actividad motora se inclinaron hacia las categorías de muchísimo, mucho, bastante y regular. Predominó la afectación moderada de la calidad de vida. El asma persistente moderada fue la mayormente referida en la afectación de calidad de vida severa.INTRODUCTION: the improvement in quality of life is a key element in treatment of asthmatic child-adolescent. OBJECTIVE: to identify the affection provoking the bronchial asthma in the quality of life of the asthmatic adolescent. METHODS: a prospective longitudinal and descriptive study was conducted in 103 asthmatic adolescents diagnosed with intermittent slight asthma from the "Antonio José de Sucre" Secondary Basic School in the Cojimar place, from January 1, to December 31, 2006. RESULTS: the major symptoms included cough, dyspnea and sibilation and the more frequent nuisances were the tiredness, profound breathlessness and the feeling of lack of air. There was

  1. The sensitivity analysis by adjoint method for the uncertainty evaluation of the CATHARE-2 code

    Energy Technology Data Exchange (ETDEWEB)

    Barre, F.; de Crecy, A.; Perret, C. [French Atomic Energy Commission (CEA), Grenoble (France)

    1995-09-01

    This paper presents the application of the DASM (Discrete Adjoint Sensitivity Method) to CATHARE 2 thermal-hydraulics code. In a first part, the basis of this method is presented. The mathematical model of the CATHARE 2 code is based on the two fluid six equation model. It is discretized using implicit time discretization and it is relatively easy to implement this method in the code. The DASM is the ASM directly applied to the algebraic system of the discretized code equations which has been demonstrated to be the only solution of the mathematical model. The ASM is an integral part of the new version 1.4 of CATHARE. It acts as a post-processing module. It has been qualified by comparison with the {open_quotes}brute force{close_quotes} technique. In a second part, an application of the DASM in CATHARE 2 is presented. It deals with the determination of the uncertainties of the constitutive relationships, which is a compulsory step for calculating the final uncertainty of a given response. First, the general principles of the method are explained: the constitutive relationship are represented by several parameters and the aim is to calculate the variance-covariance matrix of these parameters. The experimental results of the separate effect tests used to establish the correlation are considered. The variance of the corresponding results calculated by CATHARE are estimated by comparing experiment and calculation. A DASM calculation is carried out to provide the derivatives of the responses. The final covariance matrix is obtained by combination of the variance of the responses and those derivatives. Then, the application of this method to a simple case-the blowdown Canon experiment-is presented. This application has been successfully performed.

  2. Seguimiento del paciente asmático: qué debe saber el farmacéutico comunitario

    Directory of Open Access Journals (Sweden)

    Plaza Zamora J

    2013-03-01

    Full Text Available El asma tiene una prevalencia de entre un 1 y un 18% dependiendo del país. En el proceso de atención al paciente, y a través de los síntomas que presenta (disnea, tos, sibilancias, opresión torácica, el farmacéutico comunitario puede hacer educación sanitaria para evitar los agentes causales del asma, sobre cómo usar el dispositivo de inhalación prescrito por el médico, explicar al paciente su medicación, cómo es su tratamiento para conocer mejor su enfermedad, qué signos y síntomas denotan una falta de control de la misma, qué métodos se pueden usar para monitorizar la evolución del asma, detectar una posible falta de efectividad del tratamiento por tener sintomatología a pesar de estar usando adecuadamente el dispositivo de inhalación, sospechar que exista algún medicamento causante del asma, repasar el resto de medicación que usa por si existieran interacciones que afectaran tanto a la efectividad como a la seguridad del tratamiento. Existe un importante infradiagnóstico del asma, un 57,5% según el ECRHS (siglas del inglés European Community Respiratory Health Survey. En la farmacia comunitaria se puede hacer cribado de la enfermedad con la ayuda de cuestionarios validados en niños y no validados en adultos. Mediante la presente revisión se pretende ofrecer al farmacéutico comunitario una herramienta práctica para su labor diaria de atención al paciente asmático.

  3. Maduración sexual en una muestra de niños asmáticos

    Directory of Open Access Journals (Sweden)

    Gladys Abreu Suárez

    1996-04-01

    Full Text Available Con el objetivo de evaluar la repercusión del asma bronquial sobre la maduración sexual, se estudiaron en un corte transversal 180 niños asmáticos de uno y otro sexos, entre 7 y 15 años de edad, procedentes de la consulta externa del Hospital Pediátrico Docente de Centro Habana. A todos los niños se les evaluó el peso, la talla, los pliegues grasos y la maduración sexual y esquelética. Las medias de peso, talla y pliegues grasos se correspondieron con valores reportados en niños sanos. No se encontró retardo en la maduración sexual; la mayoría de los niños con estadios puberales avanzados se agruparon en los canales más altos de edad ósea.With the aim of assessing the effects of bronchial asthma on sex maturation, a cross-sectional study was carried out in 180 asthmatic children of both sexes, between 7 and 15 years old, outpatients coming from the Educational Pediatric Hospital at Centro Habana. An evaluation was made to all the children, and it included body weight, body height, skinfold thickness, bone development and sex maturation. Means in weight, height, and skinfold thickness were correspondent with the values reported for healthy children. No retardation was found in sex maturation; most part of the children with advanced pubertal stages were gathered in the highest channels of skeletal age.

  4. Code qualification of structural materials for AFCI advanced recycling reactors.

    Energy Technology Data Exchange (ETDEWEB)

    Natesan, K.; Li, M.; Majumdar, S.; Nanstad, R.K.; Sham, T.-L. (Nuclear Engineering Division); (ORNL)

    2012-05-31

    This report summarizes the further findings from the assessments of current status and future needs in code qualification and licensing of reference structural materials and new advanced alloys for advanced recycling reactors (ARRs) in support of Advanced Fuel Cycle Initiative (AFCI). The work is a combined effort between Argonne National Laboratory (ANL) and Oak Ridge National Laboratory (ORNL) with ANL as the technical lead, as part of Advanced Structural Materials Program for AFCI Reactor Campaign. The report is the second deliverable in FY08 (M505011401) under the work package 'Advanced Materials Code Qualification'. The overall objective of the Advanced Materials Code Qualification project is to evaluate key requirements for the ASME Code qualification and the Nuclear Regulatory Commission (NRC) approval of structural materials in support of the design and licensing of the ARR. Advanced materials are a critical element in the development of sodium reactor technologies. Enhanced materials performance not only improves safety margins and provides design flexibility, but also is essential for the economics of future advanced sodium reactors. Code qualification and licensing of advanced materials are prominent needs for developing and implementing advanced sodium reactor technologies. Nuclear structural component design in the U.S. must comply with the ASME Boiler and Pressure Vessel Code Section III (Rules for Construction of Nuclear Facility Components) and the NRC grants the operational license. As the ARR will operate at higher temperatures than the current light water reactors (LWRs), the design of elevated-temperature components must comply with ASME Subsection NH (Class 1 Components in Elevated Temperature Service). However, the NRC has not approved the use of Subsection NH for reactor components, and this puts additional burdens on materials qualification of the ARR. In the past licensing review for the Clinch River Breeder Reactor Project (CRBRP

  5. The network code

    International Nuclear Information System (INIS)

    1997-01-01

    The Network Code defines the rights and responsibilities of all users of the natural gas transportation system in the liberalised gas industry in the United Kingdom. This report describes the operation of the Code, what it means, how it works and its implications for the various participants in the industry. The topics covered are: development of the competitive gas market in the UK; key points in the Code; gas transportation charging; impact of the Code on producers upstream; impact on shippers; gas storage; supply point administration; impact of the Code on end users; the future. (20 tables; 33 figures) (UK)

  6. The materiality of Code

    DEFF Research Database (Denmark)

    Soon, Winnie

    2014-01-01

    , Twitter and Facebook). The focus is not to investigate the functionalities and efficiencies of the code, but to study and interpret the program level of code in order to trace the use of various technological methods such as third-party libraries and platforms’ interfaces. These are important...... to understand the socio-technical side of a changing network environment. Through the study of code, including but not limited to source code, technical specifications and other materials in relation to the artwork production, I would like to explore the materiality of code that goes beyond technical...

  7. Coding for Electronic Mail

    Science.gov (United States)

    Rice, R. F.; Lee, J. J.

    1986-01-01

    Scheme for coding facsimile messages promises to reduce data transmission requirements to one-tenth current level. Coding scheme paves way for true electronic mail in which handwritten, typed, or printed messages or diagrams sent virtually instantaneously - between buildings or between continents. Scheme, called Universal System for Efficient Electronic Mail (USEEM), uses unsupervised character recognition and adaptive noiseless coding of text. Image quality of resulting delivered messages improved over messages transmitted by conventional coding. Coding scheme compatible with direct-entry electronic mail as well as facsimile reproduction. Text transmitted in this scheme automatically translated to word-processor form.

  8. XSOR codes users manual

    International Nuclear Information System (INIS)

    Jow, Hong-Nian; Murfin, W.B.; Johnson, J.D.

    1993-11-01

    This report describes the source term estimation codes, XSORs. The codes are written for three pressurized water reactors (Surry, Sequoyah, and Zion) and two boiling water reactors (Peach Bottom and Grand Gulf). The ensemble of codes has been named ''XSOR''. The purpose of XSOR codes is to estimate the source terms which would be released to the atmosphere in severe accidents. A source term includes the release fractions of several radionuclide groups, the timing and duration of releases, the rates of energy release, and the elevation of releases. The codes have been developed by Sandia National Laboratories for the US Nuclear Regulatory Commission (NRC) in support of the NUREG-1150 program. The XSOR codes are fast running parametric codes and are used as surrogates for detailed mechanistic codes. The XSOR codes also provide the capability to explore the phenomena and their uncertainty which are not currently modeled by the mechanistic codes. The uncertainty distributions of input parameters may be used by an. XSOR code to estimate the uncertainty of source terms

  9. DLLExternalCode

    Energy Technology Data Exchange (ETDEWEB)

    2014-05-14

    DLLExternalCode is the a general dynamic-link library (DLL) interface for linking GoldSim (www.goldsim.com) with external codes. The overall concept is to use GoldSim as top level modeling software with interfaces to external codes for specific calculations. The DLLExternalCode DLL that performs the linking function is designed to take a list of code inputs from GoldSim, create an input file for the external application, run the external code, and return a list of outputs, read from files created by the external application, back to GoldSim. Instructions for creating the input file, running the external code, and reading the output are contained in an instructions file that is read and interpreted by the DLL.

  10. Development of an inelastic stress analysis code 'KINE-T' and its evaluations

    International Nuclear Information System (INIS)

    Kobatake, K.; Takahashi, S.; Suzuki, M.

    1977-01-01

    Referring to the ASME B and PVC Code Case 1592-7, the inelastic stress analysis is required for the designs of the class 1 components in elevated temperature if the results of the elastic stress analysis and/or simplified inelastic analysis do not satisfy the requirements. Authors programmed a two-dimensional axisymmetric inelastic analysis code 'KINE-T', and carried out its evaluations and an application. This FEM code is based on the incremental method and the following: elastic-plastic constitutive equation (yield condition of von Mises; flow rule of Prandtl-Reuss; Prager's hardening rule); creep constitutive equation (equation of state approach; flow rule of von Mises; strain hardening rule); the temperature dependency of the yield function is considered; solution procedure of the assembled stiffness matrix is the 'initial stress method'. After the completion of the programming, authors compared the output with not only theoretical results but also with those of the MARC code and the ANSYS code. In order to apply the code to the practical designing, authors settled a quasi-component two-dimensional axisymmetric model and a loading cycle (500 cycles). Then, an inelastic analysis and its integrity evaluation are carried out

  11. The Development of the Code Safety Valve Test Facility

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chang Hyun; Kim, Young Ae; Park, Jong Woon [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

    2007-07-01

    The Pressurizer Safety Valves (PSV) in Pressurized Water Reactors (PWRs) are required to provide the overpressure protection for the Reactor Coolant System (RCS) during the overpressure transients. According to the ASME OM code, all safety valves should be tested every 5 years with the acceptance tolerance of 1%. If one valve failed to meet this criterion, other two additional valves should be tested and if these valves don't meet the requirement, all valves should be tested. These frequent tests may make the valves decrepit and become a cause of leak. Therefore, increase of the acceptance tolerance is vital for the safe operation of the plant. In the United States, the acceptance tolerances are enlarged up to about 3% in most plants. This requires re-analysis of relevant accidents in FSAR. Also, the technical background data for the valve pop-up characteristics and the loop seal dynamics (if the plant has the loop seal in the upstream of PSV) are needed for the new safety analysis. Korea Hydro and Nuclear Power Company (KHNP) plans to build the PSV test facility for the purpose of providing the background data. This paper describes the preliminary design of the facility and studies on the system dynamics using GOTHIC-7.2a code to verify the pressure vessel capacities and to find the best operating condition.

  12. The Aesthetics of Coding

    DEFF Research Database (Denmark)

    Andersen, Christian Ulrik

    2007-01-01

    Computer art is often associated with computer-generated expressions (digitally manipulated audio/images in music, video, stage design, media facades, etc.). In recent computer art, however, the code-text itself – not the generated output – has become the artwork (Perl Poetry, ASCII Art, obfuscated...... code, etc.). The presentation relates this artistic fascination of code to a media critique expressed by Florian Cramer, claiming that the graphical interface represents a media separation (of text/code and image) causing alienation to the computer’s materiality. Cramer is thus the voice of a new ‘code...... avant-garde’. In line with Cramer, the artists Alex McLean and Adrian Ward (aka Slub) declare: “art-oriented programming needs to acknowledge the conditions of its own making – its poesis.” By analysing the Live Coding performances of Slub (where they program computer music live), the presentation...

  13. The aeroelastic code FLEXLAST

    Energy Technology Data Exchange (ETDEWEB)

    Visser, B. [Stork Product Eng., Amsterdam (Netherlands)

    1996-09-01

    To support the discussion on aeroelastic codes, a description of the code FLEXLAST was given and experiences within benchmarks and measurement programmes were summarized. The code FLEXLAST has been developed since 1982 at Stork Product Engineering (SPE). Since 1992 FLEXLAST has been used by Dutch industries for wind turbine and rotor design. Based on the comparison with measurements, it can be concluded that the main shortcomings of wind turbine modelling lie in the field of aerodynamics, wind field and wake modelling. (au)

  14. Gauge color codes

    DEFF Research Database (Denmark)

    Bombin Palomo, Hector

    2015-01-01

    Color codes are topological stabilizer codes with unusual transversality properties. Here I show that their group of transversal gates is optimal and only depends on the spatial dimension, not the local geometry. I also introduce a generalized, subsystem version of color codes. In 3D they allow t...... the transversal implementation of a universal set of gates by gauge fixing, while error-dectecting measurements involve only four or six qubits....

  15. Doubled Color Codes

    Science.gov (United States)

    Bravyi, Sergey

    Combining protection from noise and computational universality is one of the biggest challenges in the fault-tolerant quantum computing. Topological stabilizer codes such as the 2D surface code can tolerate a high level of noise but implementing logical gates, especially non-Clifford ones, requires a prohibitively large overhead due to the need of state distillation. In this talk I will describe a new family of 2D quantum error correcting codes that enable a transversal implementation of all logical gates required for the universal quantum computing. Transversal logical gates (TLG) are encoded operations that can be realized by applying some single-qubit rotation to each physical qubit. TLG are highly desirable since they introduce no overhead and do not spread errors. It has been known before that a quantum code can have only a finite number of TLGs which rules out computational universality. Our scheme circumvents this no-go result by combining TLGs of two different quantum codes using the gauge-fixing method pioneered by Paetznick and Reichardt. The first code, closely related to the 2D color code, enables a transversal implementation of all single-qubit Clifford gates such as the Hadamard gate and the π / 2 phase shift. The second code that we call a doubled color code provides a transversal T-gate, where T is the π / 4 phase shift. The Clifford+T gate set is known to be computationally universal. The two codes can be laid out on the honeycomb lattice with two qubits per site such that the code conversion requires parity measurements for six-qubit Pauli operators supported on faces of the lattice. I will also describe numerical simulations of logical Clifford+T circuits encoded by the distance-3 doubled color code. Based on a joint work with Andrew Cross.

  16. Phonological coding during reading

    Science.gov (United States)

    Leinenger, Mallorie

    2014-01-01

    The exact role that phonological coding (the recoding of written, orthographic information into a sound based code) plays during silent reading has been extensively studied for more than a century. Despite the large body of research surrounding the topic, varying theories as to the time course and function of this recoding still exist. The present review synthesizes this body of research, addressing the topics of time course and function in tandem. The varying theories surrounding the function of phonological coding (e.g., that phonological codes aid lexical access, that phonological codes aid comprehension and bolster short-term memory, or that phonological codes are largely epiphenomenal in skilled readers) are first outlined, and the time courses that each maps onto (e.g., that phonological codes come online early (pre-lexical) or that phonological codes come online late (post-lexical)) are discussed. Next the research relevant to each of these proposed functions is reviewed, discussing the varying methodologies that have been used to investigate phonological coding (e.g., response time methods, reading while eyetracking or recording EEG and MEG, concurrent articulation) and highlighting the advantages and limitations of each with respect to the study of phonological coding. In response to the view that phonological coding is largely epiphenomenal in skilled readers, research on the use of phonological codes in prelingually, profoundly deaf readers is reviewed. Finally, implications for current models of word identification (activation-verification model (Van Order, 1987), dual-route model (e.g., Coltheart, Rastle, Perry, Langdon, & Ziegler, 2001), parallel distributed processing model (Seidenberg & McClelland, 1989)) are discussed. PMID:25150679

  17. MORSE Monte Carlo code

    Energy Technology Data Exchange (ETDEWEB)

    Cramer, S.N.

    1984-01-01

    The MORSE code is a large general-use multigroup Monte Carlo code system. Although no claims can be made regarding its superiority in either theoretical details or Monte Carlo techniques, MORSE has been, since its inception at ORNL in the late 1960s, the most widely used Monte Carlo radiation transport code. The principal reason for this popularity is that MORSE is relatively easy to use, independent of any installation or distribution center, and it can be easily customized to fit almost any specific need. Features of the MORSE code are described.

  18. Bar Code Labels

    Science.gov (United States)

    1988-01-01

    American Bar Codes, Inc. developed special bar code labels for inventory control of space shuttle parts and other space system components. ABC labels are made in a company-developed anodizing aluminum process and consecutively marketed with bar code symbology and human readable numbers. They offer extreme abrasion resistance and indefinite resistance to ultraviolet radiation, capable of withstanding 700 degree temperatures without deterioration and up to 1400 degrees with special designs. They offer high resistance to salt spray, cleaning fluids and mild acids. ABC is now producing these bar code labels commercially or industrial customers who also need labels to resist harsh environments.

  19. QR codes for dummies

    CERN Document Server

    Waters, Joe

    2012-01-01

    Find out how to effectively create, use, and track QR codes QR (Quick Response) codes are popping up everywhere, and businesses are reaping the rewards. Get in on the action with the no-nonsense advice in this streamlined, portable guide. You'll find out how to get started, plan your strategy, and actually create the codes. Then you'll learn to link codes to mobile-friendly content, track your results, and develop ways to give your customers value that will keep them coming back. It's all presented in the straightforward style you've come to know and love, with a dash of humor thrown

  20. MORSE Monte Carlo code

    International Nuclear Information System (INIS)

    Cramer, S.N.

    1984-01-01

    The MORSE code is a large general-use multigroup Monte Carlo code system. Although no claims can be made regarding its superiority in either theoretical details or Monte Carlo techniques, MORSE has been, since its inception at ORNL in the late 1960s, the most widely used Monte Carlo radiation transport code. The principal reason for this popularity is that MORSE is relatively easy to use, independent of any installation or distribution center, and it can be easily customized to fit almost any specific need. Features of the MORSE code are described

  1. Tokamak Systems Code

    International Nuclear Information System (INIS)

    Reid, R.L.; Barrett, R.J.; Brown, T.G.

    1985-03-01

    The FEDC Tokamak Systems Code calculates tokamak performance, cost, and configuration as a function of plasma engineering parameters. This version of the code models experimental tokamaks. It does not currently consider tokamak configurations that generate electrical power or incorporate breeding blankets. The code has a modular (or subroutine) structure to allow independent modeling for each major tokamak component or system. A primary benefit of modularization is that a component module may be updated without disturbing the remainder of the systems code as long as the imput to or output from the module remains unchanged

  2. ARC Code TI: ACCEPT

    Data.gov (United States)

    National Aeronautics and Space Administration — ACCEPT consists of an overall software infrastructure framework and two main software components. The software infrastructure framework consists of code written to...

  3. A avaliação da Qualidade de Vida no Doente Asmático

    Directory of Open Access Journals (Sweden)

    C.H. Leroyer

    1998-11-01

    Full Text Available RESUMO: A avaliarção da Qualidade de Vida (QV do doente respiratório crónico, tem suscitado um interesse cresceote nos últimos anos. O conceito de QV é complexo, sendo, segundo o grupo de trabalho da OMS sobre este tema: “… influenciado pelo estado de saúde fisico, psicológico, o grau de independência, a inserrção social e as relarções com os constituintes essenciais do meio ambiente”. Neste trabalho, os autores abordam a importância e o lugar da avaliação da QV no estudo do doente com asma brônquica e analisam OS diferéntes métodos de avaliação disponíveis.Tal como as outras doenças respiratórias crónicas, a asma tem repercussões na qualidade de vida dos doentes. Como resposta, o.doente asmàtico pode desenvolver mecanismos de adaptação complexos, ex: diminuir o seu nível de actividade funcional (fenómeno de “normalidade ajustada” em que ao fim de certo tempo, a incapacidade para a realização de certas actividades fisicas é assumido pelo doente como “normal”. A avaliação da qualidade de vida deve, nestes casos, ser capaz de evidenciar a real limitação da actividade do doente.Os factores exteriores (ex: elirna, também exercem uma influência determinante sobre o doente asmátìco. Em resposta a estes, o doente pode limitar a sua actividadc (ex: evitar ambientcs enfumarados ou evitar o exercicio ao ar livre nos dias frios ou pode alterar o meio ambientc (ex: medidas de evicção dos ácaros.A asma brônquica afecta três domínios da vida do indivíduo: Físico, Psíquico e Social. Como resultado, a avaliarção da QV do doente asmático é um estudo pluridimensional e deve ser encarada como complementar dos restantes indicadores habitualmente empregues no estudo da asma (estudo funcional respiratório, análiscs, “scores” clinicos, etc.. Além disso

  4. Report on the activities of the ASME-NQA Committee Working Group on Quality Assurance Requirements for Research and Development, April 1990 to August 1991

    Energy Technology Data Exchange (ETDEWEB)

    Dronkers, J.J.

    1991-09-01

    This report transmits to the public eye the activities of the American Society of Mechanical Engineers-Nuclear Quality Assurance (ASME-NQA) Committee Working Group on Quality Assurance Requirements for Research and Development. The appendix lists the members of this group as of August 1991. The report covers a period of 17 months. The working group met eight times in this period, and much intellectual ground was traversed. There was seldom agreement on the nature of the task, but there was no doubt as to its urgency. The task was how to adapt the nuclear quality assurance standard, the NQA-1, to research and development work. 1 fig., 7 tabs.

  5. Função respiratória em filhos de mães asmáticas

    Directory of Open Access Journals (Sweden)

    Marco A. Valadares

    2013-04-01

    Full Text Available OBJETIVO: Avaliar a função pulmonar e as manifestações clínicas sugestivas de asma em filhos de mães com diagnóstico médico referido de asma. MÉTODOS: Estudo observacional transversal analítico aninhado a uma coorte de 4.757 parturientes. Foram avaliadas 86 crianças aos seis anos de idade, filhas de mães com diagnóstico médico de asma antes da gestação. Foram coletadas informações referentes a sintomatologias clínicas de atopias e doenças respiratórias, variáveis socioeconômicas e de exposição; tendo sido as crianças submetidas à espirometria. RESULTADOS: Foram encontrados 30,3% de alterações espirométricas, havendo predomínio do diagnóstico de asma nos que apresentaram padrão obstrutivo. Diagnóstico médico pregresso de asma ocorreu em 9,3% das crianças; contudo, o diagnóstico estabelecido a partir da presença e frequência dos sintomas de asma representou 18,6%. Das 86 crianças participantes, 37,2% tiveram um escore de cinco ou mais pontos no questionário ISAAC, estando isso associado à alteração do padrão espirométrico (p = 0,002. Após a regressão logística múltipla, maior escolaridade paterna, maior número de quartos no domicílio e o fato de a mãe não ter apresentado "chiado" durante a gestação foram estatisticamente significantes como fatores protetores para a presença de distúrbio ventilatório à espirometria. CONCLUSÕES: A frequência de alterações do teste espirométrico em filhos de mães asmáticas foi alta, com o padrão restritivo ocorrendo mais vezes que o obstrutivo. Houve uma maior ocorrência de exames obstrutivos naqueles que apresentavam sintomatologia clínica de asma, com uma frequência de diagnóstico clínico de asma superior à encontrada na literatura.

  6. The effectiveness of fish oil supplementation in asthmatic rats is limited by an inefficient action on ASM function.

    Science.gov (United States)

    Miranda, D T S Z; Zanatta, A L; Dias, B C L; Fogaça, R T H; Maurer, J B B; Donatti, L; Calder, P C; Nishiyama, A

    2013-09-01

    Episodes of acute exacerbation are the major clinical feature of asthma and therefore represent an important focus for developing novel therapies for this disease. There are many reports that the n-3 fatty acids found in fish oil exert anti-inflammatory effects, but there are few studies of the action of fish oil on airway smooth muscle (ASM) function. In the present investigation, we evaluated the effect of fish oil supplementation on smooth muscle force of contraction in ovalbumin-induced asthmatic Wistar rats, and its consequences on static lung compliance, mucus production, leukocyte chemotaxis and production of proinflammatory cytokines. Fish oil supplementation suppressed the infiltration of inflammatory cells into the lung in asthmatic animals (2.04 ± 0.19 × 10(6) cells vs. 3.33 ± 0.43 × 10(6) cells in the control asthmatic group; P < 0.05). Static lung compliance increased with fish oil supplementation in asthmatic rats (0.640 ± 0.053 mL/cm H2O vs. 0.399 ± 0.043 mL/cm H2O; P < 0.05). However, fish oil did not prevent asthma-associated lung eosinophilia and did not affect the concentrations of tumor necrosis factor-α and interleukin-1β in lung tissue or the proportion of the airways obliterated with mucus. Fish oil had no effect on the force of contraction in asthmatic rats in response to acetylcholine (3.026 ± 0.274 mN vs. 2.813 ± 0.364 mN in the control asthmatic group). In conclusion, although fish oil exerts some benefits in this model of asthma, its effectiveness appears to be limited by an inefficient action on airway smooth muscle function.

  7. Modifications to LLNL Plutonium Packaging Systems (PuPS) to achieve ASME VIII UW-13.2(d) Requirements for the DOE Standard 3013-00 Outer Can Weld

    International Nuclear Information System (INIS)

    Riley, D; Dodson, K

    2001-01-01

    The Lawrence Livermore National Laboratory (LLNL) Plutonium Packaging System (PuPS) prepares packages to meet the DOE Standard 3013 (Reference 1). The PuPS equipment was supplied by the British Nuclear Fuels Limited (BNFL). The DOE Standard 3013 requires that the welding of the Outer Can meets ASME Section VIII Division 1 (Reference 2). ASME Section VIII references to ASME Section IX (Reference 3) for most of the welding requirements, but UW-13.2 (d) of Section VIII requires a certain depth and width of the weld. In this document the UW-13.2(d) requirement is described as the (a+b)/2t s ratio. This ratio has to be greater than or equal to one to meet the requirements of UW-13.2(d). The Outer Can welds had not been meeting this requirement. Three methods are being followed to resolve this issue: (1) Modify the welding parameters to achieve the requirement, (2) Submit a weld case to ASME that changes the UW-13.2(d) requirement for their review and approval, and (3) Change the requirements in the DOE-STD-3013. Each of these methods are being pursued. This report addresses how the first method was addressed for the LLNL PuPS. The experimental work involved adjusting the Outer Can rotational speed and the power applied to the can. These adjustments resulted in being able to achieve the ASME VIII, UW-13.2(d) requirement

  8. On {\\sigma}-LCD codes

    OpenAIRE

    Carlet, Claude; Mesnager, Sihem; Tang, Chunming; Qi, Yanfeng

    2017-01-01

    Linear complementary pairs (LCP) of codes play an important role in armoring implementations against side-channel attacks and fault injection attacks. One of the most common ways to construct LCP of codes is to use Euclidean linear complementary dual (LCD) codes. In this paper, we first introduce the concept of linear codes with $\\sigma$ complementary dual ($\\sigma$-LCD), which includes known Euclidean LCD codes, Hermitian LCD codes, and Galois LCD codes. As Euclidean LCD codes, $\\sigma$-LCD ...

  9. Pipe elbow stiffness coefficients including shear and bend flexibility factors for use in direct stiffness codes

    International Nuclear Information System (INIS)

    Perry, R.F.

    1977-01-01

    Historically, developments of computer codes used for piping analysis were based upon the flexibility method of structural analysis. Because of the specialized techniques employed in this method, the codes handled systems composed of only piping elements. Over the past ten years, the direct stiffness method has gained great popularity because of its systematic solution procedure regardless of the type of structural elements composing the system. A great advantage is realized with a direct stiffness code that combines piping elements along with other structural elements such as beams, plates, and shells, in a single model. One common problem, however, has been the lack of an accurate pipe elbow element that would adequately represent the effects of transverse shear and bend flexibility factors. The purpose of the present paper is to present a systematic derivation of the required 12x12 stiffness matrix and load vectors for a three dimensional pipe elbow element which includes the effects of transverse shear and pipe bend flexibility according to the ASME Boiler and Pressure Vessel Code, Section III. The results are presented analytically and as FORTRAN subroutines to be directly incorporated into existing direct stiffness codes. (Auth.)

  10. Opening up codings?

    DEFF Research Database (Denmark)

    Steensig, Jakob; Heinemann, Trine

    2015-01-01

    We welcome Tanya Stivers’s discussion (Stivers, 2015/this issue) of coding social interaction and find that her descriptions of the processes of coding open up important avenues for discussion, among other things of the precise ad hoc considerations that researchers need to bear in mind, both when...

  11. Error Correcting Codes -34 ...

    Indian Academy of Sciences (India)

    Science, Bangalore. Her interests are in. Theoretical Computer. Science. SERIES I ARTICLE. Error Correcting Codes. 2. The Hamming Codes. Priti Shankar. In the first article of this series we showed how redundancy introduced into a message transmitted over a noisy channel could improve the reliability of transmission. In.

  12. Decoding Codes on Graphs

    Indian Academy of Sciences (India)

    set up a well defined goal - that of achieving a per- formance bound set by the noisy channel coding theo- rem, proved in the paper. Whereas the goal appeared elusive twenty five years ago, today, there are practi- cal codes and decoding algorithms that come close to achieving it. It is interesting to note that all known.

  13. Error Correcting Codes

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 3. Error Correcting Codes - Reed Solomon Codes. Priti Shankar. Series Article Volume 2 Issue 3 March 1997 pp 33-47. Fulltext. Click here to view fulltext PDF. Permanent link: http://www.ias.ac.in/article/fulltext/reso/002/03/0033-0047 ...

  14. Insurance billing and coding.

    Science.gov (United States)

    Napier, Rebecca H; Bruelheide, Lori S; Demann, Eric T K; Haug, Richard H

    2008-07-01

    The purpose of this article is to highlight the importance of understanding various numeric and alpha-numeric codes for accurately billing dental and medically related services to private pay or third-party insurance carriers. In the United States, common dental terminology (CDT) codes are most commonly used by dentists to submit claims, whereas current procedural terminology (CPT) and International Classification of Diseases, Ninth Revision, Clinical Modification (ICD.9.CM) codes are more commonly used by physicians to bill for their services. The CPT and ICD.9.CM coding systems complement each other in that CPT codes provide the procedure and service information and ICD.9.CM codes provide the reason or rationale for a particular procedure or service. These codes are more commonly used for "medical necessity" determinations, and general dentists and specialists who routinely perform care, including trauma-related care, biopsies, and dental treatment as a result of or in anticipation of a cancer-related treatment, are likely to use these codes. Claim submissions for care provided can be completed electronically or by means of paper forms.

  15. Codes of Conduct

    Science.gov (United States)

    Million, June

    2004-01-01

    Most schools have a code of conduct, pledge, or behavioral standards, set by the district or school board with the school community. In this article, the author features some schools that created a new vision of instilling code of conducts to students based on work quality, respect, safety and courtesy. She suggests that communicating the code…

  16. Decoding Codes on Graphs

    Indian Academy of Sciences (India)

    Department of Computer. Science 'and Automation,. lISe. Their research addresses ... The fifty five year old history of error correcting codes began with Claude Shannon's path-breaking paper en- titled 'A ... given the limited computing power available then, Gal- lager's codes were not considered practical. A landmark.

  17. Error Correcting Codes

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 2; Issue 3. Error Correcting Codes - Reed Solomon Codes. Priti Shankar. Series Article Volume 2 Issue 3 March ... Author Affiliations. Priti Shankar1. Department of Computer Science and Automation, Indian Institute of Science, Bangalore 560 012, India ...

  18. Decoding Codes on Graphs

    Indian Academy of Sciences (India)

    Home; Journals; Resonance – Journal of Science Education; Volume 8; Issue 9. Decoding Codes on Graphs - Low Density Parity Check Codes. A S Madhu Aditya Nori. General Article Volume 8 Issue 9 September 2003 pp 49-59. Fulltext. Click here to view fulltext PDF. Permanent link:

  19. READING A NEURAL CODE

    NARCIS (Netherlands)

    BIALEK, W; RIEKE, F; VANSTEVENINCK, RRD; WARLAND, D

    1991-01-01

    Traditional approaches to neural coding characterize the encoding of known stimuli in average neural responses. Organisms face nearly the opposite task - extracting information about an unknown time-dependent stimulus from short segments of a spike train. Here the neural code was characterized from

  20. Fracture flow code

    International Nuclear Information System (INIS)

    Dershowitz, W; Herbert, A.; Long, J.

    1989-03-01

    The hydrology of the SCV site will be modelled utilizing discrete fracture flow models. These models are complex, and can not be fully cerified by comparison to analytical solutions. The best approach for verification of these codes is therefore cross-verification between different codes. This is complicated by the variation in assumptions and solution techniques utilized in different codes. Cross-verification procedures are defined which allow comparison of the codes developed by Harwell Laboratory, Lawrence Berkeley Laboratory, and Golder Associates Inc. Six cross-verification datasets are defined for deterministic and stochastic verification of geometric and flow features of the codes. Additional datasets for verification of transport features will be documented in a future report. (13 figs., 7 tabs., 10 refs.) (authors)

  1. Validation of thermalhydraulic codes

    International Nuclear Information System (INIS)

    Wilkie, D.

    1992-01-01

    Thermalhydraulic codes require to be validated against experimental data collected over a wide range of situations if they are to be relied upon. A good example is provided by the nuclear industry where codes are used for safety studies and for determining operating conditions. Errors in the codes could lead to financial penalties, to the incorrect estimation of the consequences of accidents and even to the accidents themselves. Comparison between prediction and experiment is often described qualitatively or in approximate terms, e.g. ''agreement is within 10%''. A quantitative method is preferable, especially when several competing codes are available. The codes can then be ranked in order of merit. Such a method is described. (Author)

  2. Exercise-induced Bronchospasm In Obese And Non-obese Asthmatic Adolescents [broncoespasmo Induzido Pelo Exercício Em Adolescentes Asmáticos Obesos E Não-obesos

    OpenAIRE

    Lopes W.A.; Leite N.; Rosario N.

    2010-01-01

    OBJETIVO: Avaliar e comparar a frequência e intensidade do broncoespasmo induzido pelo exercício (BIE) em adolescentes asmáticos obesos e não-obesos. MÉTODOS: Estudo transversal e descritivo realizado com 39 adolescentes de ambos os sexos, com idade entre dez e 16 anos, divididos em dois grupos conforme o histórico clínico de asma e/ou rinite alérgica e o índice de massa corporal: asmáticos obesos (n=18); asmáticos não-obesos (n=21). Utilizou-se o teste de broncoprovocação com exercício para ...

  3. Report number codes

    International Nuclear Information System (INIS)

    Nelson, R.N.

    1985-05-01

    This publication lists all report number codes processed by the Office of Scientific and Technical Information. The report codes are substantially based on the American National Standards Institute, Standard Technical Report Number (STRN)-Format and Creation Z39.23-1983. The Standard Technical Report Number (STRN) provides one of the primary methods of identifying a specific technical report. The STRN consists of two parts: The report code and the sequential number. The report code identifies the issuing organization, a specific program, or a type of document. The sequential number, which is assigned in sequence by each report issuing entity, is not included in this publication. Part I of this compilation is alphabetized by report codes followed by issuing installations. Part II lists the issuing organization followed by the assigned report code(s). In both Parts I and II, the names of issuing organizations appear for the most part in the form used at the time the reports were issued. However, for some of the more prolific installations which have had name changes, all entries have been merged under the current name

  4. Report number codes

    Energy Technology Data Exchange (ETDEWEB)

    Nelson, R.N. (ed.)

    1985-05-01

    This publication lists all report number codes processed by the Office of Scientific and Technical Information. The report codes are substantially based on the American National Standards Institute, Standard Technical Report Number (STRN)-Format and Creation Z39.23-1983. The Standard Technical Report Number (STRN) provides one of the primary methods of identifying a specific technical report. The STRN consists of two parts: The report code and the sequential number. The report code identifies the issuing organization, a specific program, or a type of document. The sequential number, which is assigned in sequence by each report issuing entity, is not included in this publication. Part I of this compilation is alphabetized by report codes followed by issuing installations. Part II lists the issuing organization followed by the assigned report code(s). In both Parts I and II, the names of issuing organizations appear for the most part in the form used at the time the reports were issued. However, for some of the more prolific installations which have had name changes, all entries have been merged under the current name.

  5. Laser propagation code study

    OpenAIRE

    Rockower, Edward B.

    1985-01-01

    A number of laser propagation codes have been assessed as to their suitability for modeling Army High Energy Laser (HEL) weapons used in an anti- sensor mode. We identify a number of areas in which systems analysis HEL codes are deficient. Most notably, available HEL scaling law codes model the laser aperture as circular, possibly with a fixed (e.g. 10%) obscuration. However, most HELs have rectangular apertures with up to 30% obscuration. We present a beam-quality/aperture shape scaling rela...

  6. Transport theory and codes

    International Nuclear Information System (INIS)

    Clancy, B.E.

    1986-01-01

    This chapter begins with a neutron transport equation which includes the one dimensional plane geometry problems, the one dimensional spherical geometry problems, and numerical solutions. The section on the ANISN code and its look-alikes covers problems which can be solved; eigenvalue problems; outer iteration loop; inner iteration loop; and finite difference solution procedures. The input and output data for ANISN is also discussed. Two dimensional problems such as the DOT code are given. Finally, an overview of the Monte-Carlo methods and codes are elaborated on

  7. Gravity inversion code

    International Nuclear Information System (INIS)

    Burkhard, N.R.

    1979-01-01

    The gravity inversion code applies stabilized linear inverse theory to determine the topography of a subsurface density anomaly from Bouguer gravity data. The gravity inversion program consists of four source codes: SEARCH, TREND, INVERT, and AVERAGE. TREND and INVERT are used iteratively to converge on a solution. SEARCH forms the input gravity data files for Nevada Test Site data. AVERAGE performs a covariance analysis on the solution. This document describes the necessary input files and the proper operation of the code. 2 figures, 2 tables

  8. Decoding the productivity code

    DEFF Research Database (Denmark)

    Hansen, David

    , that is, the productivity code of the 21st century, is dissolved. Today, organizations are pressured for operational efficiency, often in terms of productivity, due to increased global competition, demographical changes, and use of natural resources. Taylor’s principles for rationalization founded...... that swing between rationalization and employee development. The productivity code is the lack of alternatives to this ineffective approach. This thesis decodes the productivity code based on the results from a 3-year action research study at a medium-sized manufacturing facility. During the project period...

  9. CALIPSOS code report

    International Nuclear Information System (INIS)

    Fanselau, R.W.; Thakkar, J.G.; Hiestand, J.W.; Cassell, D.S.

    1980-04-01

    CALIPSOS is a steady-state three-dimensional flow distribution code which predicts the fluid dynamics and heat transfer interactions of the secondary two-phase flow in a steam generator. The mathematical formulation is sufficiently general to accommodate two fluid models described by separate gas and liquid momentum equations. However, if the user selects the homogeneous flow option, the code automatically equates the gas and liquid phase velocities (thereby reducing the number of momentum equations solved to three) and utilizes a homogeneous density mixture. This report presents the basic features of the CALIPSOS code and includes assumptions, equations solved, the finite-difference grid, and highlights of the solution procedure

  10. Cryptography cracking codes

    CERN Document Server

    2014-01-01

    While cracking a code might seem like something few of us would encounter in our daily lives, it is actually far more prevalent than we may realize. Anyone who has had personal information taken because of a hacked email account can understand the need for cryptography and the importance of encryption-essentially the need to code information to keep it safe. This detailed volume examines the logic and science behind various ciphers, their real world uses, how codes can be broken, and the use of technology in this oft-overlooked field.

  11. Experimental characterization and modeling of the creep strength at 550 C of ASME Grade 92 steel welded joints

    International Nuclear Information System (INIS)

    Kalck, Ch.

    2012-01-01

    In the framework of the development of Generation IV nuclear power plants, ASME Grade 92 ferritic-martensitic steel is a candidate material for components subjected to long-term creep at high temperature. The aim of this study is to characterize the microstructure of Grade 92 butt welded joints and to model their creep behavior at 550 C. Two filler rods were used for this study. The microstructure of the different weld regions was quantitatively characterized. In order to understand the weaker mechanical properties of the ICHAZ compared to the other regions of the welded joint, the microstructures of the base metal and the ICHAZ were compared at different scales (SEM, EBSD, TEM on thin foils and extractive replicas). No significant difference regarding micro-texture, sub-structure and precipitation state was highlighted between both microstructures. The origin of the weaker resistance of the ICHAZ to viscoplastic flow is still not fully understood. A softer zone was found in the base metal close to the ICHAZ, yet with finer sub-grains than the base metal. It was supposed to be a thermo-mechanically-affected zone (TMAZ). At high temperatures and low stress levels, Grade 92 welded joints may be sensitive to type IV cracking, which occurs in the inter-critical heat affected zone (ICHAZ). Creep tests conducted at 550 C on cross-weld specimens revealed that fracture takes place in the ICHAZ, even for short-term creep tests (i.e., lifetime lower than 1000 h). In order to model the creep behavior of the welded joint, viscoplastic constitutive equations for the different regions of the weld assembly were required. The viscoplastic behavior of the base metal, weld metal and of the ICHAZ were modeled using a phenomenological approach. The viscoplastic flow behavior of the weld metal and of the ICHAZ was experimentally determined (i) from tensile tests with displacement field measurements and (ii) from creep tests on tensile bars notched in the region of interest. An

  12. Evaluation procedure of the structural integrity of a pipe of nuclear use. Application of codes for design and service. Case study

    International Nuclear Information System (INIS)

    Sanzi, H.; Asta, E.

    2009-01-01

    In the present work, we are presenting the most important results of the local stresses occurred in the cracked pipes with a axial through-wall, under Failure Concept 0.1A, using Finite Element Method and Fracture Mechanics. As requested, the component has been verified based 3D FE plastic analysis, under the postulated failure loading, assuring with this method a high degree of accuracy in the results. Codes used by Design and Service, as ASME Section III Div. 1 and API 579, have been used in the analysis. (author)

  13. The fast code

    Energy Technology Data Exchange (ETDEWEB)

    Freeman, L.N.; Wilson, R.E. [Oregon State Univ., Dept. of Mechanical Engineering, Corvallis, OR (United States)

    1996-09-01

    The FAST Code which is capable of determining structural loads on a flexible, teetering, horizontal axis wind turbine is described and comparisons of calculated loads with test data are given at two wind speeds for the ESI-80. The FAST Code models a two-bladed HAWT with degrees of freedom for blade bending, teeter, drive train flexibility, yaw, and windwise and crosswind tower motion. The code allows blade dimensions, stiffnesses, and weights to differ and models tower shadow, wind shear, and turbulence. Additionally, dynamic stall is included as are delta-3 and an underslung rotor. Load comparisons are made with ESI-80 test data in the form of power spectral density, rainflow counting, occurrence histograms, and azimuth averaged bin plots. It is concluded that agreement between the FAST Code and test results is good. (au)

  14. Fulcrum Network Codes

    DEFF Research Database (Denmark)

    2015-01-01

    Fulcrum network codes, which are a network coding framework, achieve three objectives: (i) to reduce the overhead per coded packet to almost 1 bit per source packet; (ii) to operate the network using only low field size operations at intermediate nodes, dramatically reducing complexity...... in the network; and (iii) to deliver an end-to-end performance that is close to that of a high field size network coding system for high-end receivers while simultaneously catering to low-end ones that can only decode in a lower field size. Sources may encode using a high field size expansion to increase...... the number of dimensions seen by the network using a linear mapping. Receivers can tradeoff computational effort with network delay, decoding in the high field size, the low field size, or a combination thereof....

  15. Code Disentanglement: Initial Plan

    Energy Technology Data Exchange (ETDEWEB)

    Wohlbier, John Greaton [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Kelley, Timothy M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Rockefeller, Gabriel M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Calef, Matthew Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-01-27

    The first step to making more ambitious changes in the EAP code base is to disentangle the code into a set of independent, levelized packages. We define a package as a collection of code, most often across a set of files, that provides a defined set of functionality; a package a) can be built and tested as an entity and b) fits within an overall levelization design. Each package contributes one or more libraries, or an application that uses the other libraries. A package set is levelized if the relationships between packages form a directed, acyclic graph and each package uses only packages at lower levels of the diagram (in Fortran this relationship is often describable by the use relationship between modules). Independent packages permit independent- and therefore parallel|development. The packages form separable units for the purposes of development and testing. This is a proven path for enabling finer-grained changes to a complex code.

  16. Coded Random Access

    DEFF Research Database (Denmark)

    Paolini, Enrico; Stefanovic, Cedomir; Liva, Gianluigi

    2015-01-01

    The rise of machine-to-machine communications has rekindled the interest in random access protocols as a support for a massive number of uncoordinatedly transmitting devices. The legacy ALOHA approach is developed under a collision model, where slots containing collided packets are considered...... as waste. However, if the common receiver (e.g., base station) is capable to store the collision slots and use them in a transmission recovery process based on successive interference cancellation, the design space for access protocols is radically expanded. We present the paradigm of coded random access......, in which the structure of the access protocol can be mapped to a structure of an erasure-correcting code defined on graph. This opens the possibility to use coding theory and tools for designing efficient random access protocols, offering markedly better performance than ALOHA. Several instances of coded...

  17. VT ZIP Code Areas

    Data.gov (United States)

    Vermont Center for Geographic Information — (Link to Metadata) A ZIP Code Tabulation Area (ZCTA) is a statistical geographic entity that approximates the delivery area for a U.S. Postal Service five-digit...

  18. Induction technology optimization code

    International Nuclear Information System (INIS)

    Caporaso, G.J.; Brooks, A.L.; Kirbie, H.C.

    1992-01-01

    A code has been developed to evaluate relative costs of induction accelerator driver systems for relativistic klystrons. The code incorporates beam generation, transport and pulsed power system constraints to provide an integrated design tool. The code generates an injector/accelerator combination which satisfies the top level requirements and all system constraints once a small number of design choices have been specified (rise time of the injector voltage and aspect ratio of the ferrite induction cores, for example). The code calculates dimensions of accelerator mechanical assemblies and values of all electrical components. Cost factors for machined parts, raw materials and components are applied to yield a total system cost. These costs are then plotted as a function of the two design choices to enable selection of an optimum design based on various criteria. (Author) 11 refs., 3 figs

  19. Code de conduite

    International Development Research Centre (IDRC) Digital Library (Canada)

    irocca

    le respect de telles normes. Ce faisant, nous contribuons à la bonne réputation et à l'intégrité du Centre et allons dans le sens du Code de valeurs et d'éthique du secteur public du gouvernement du Canada. Je vous invite à prendre connaissance de cette nouvelle mouture du Code de conduite et à appliquer ses principes ...

  20. Towards advanced code simulators

    International Nuclear Information System (INIS)

    Scriven, A.H.

    1990-01-01

    The Central Electricity Generating Board (CEGB) uses advanced thermohydraulic codes extensively to support PWR safety analyses. A system has been developed to allow fully interactive execution of any code with graphical simulation of the operator desk and mimic display. The system operates in a virtual machine environment, with the thermohydraulic code executing in one virtual machine, communicating via interrupts with any number of other virtual machines each running other programs and graphics drivers. The driver code itself does not have to be modified from its normal batch form. Shortly following the release of RELAP5 MOD1 in IBM compatible form in 1983, this code was used as the driver for this system. When RELAP5 MOD2 became available, it was adopted with no changes needed in the basic system. Overall the system has been used for some 5 years for the analysis of LOBI tests, full scale plant studies and for simple what-if studies. For gaining rapid understanding of system dependencies it has proved invaluable. The graphical mimic system, being independent of the driver code, has also been used with other codes to study core rewetting, to replay results obtained from batch jobs on a CRAY2 computer system and to display suitably processed experimental results from the LOBI facility to aid interpretation. For the above work real-time execution was not necessary. Current work now centers on implementing the RELAP 5 code on a true parallel architecture machine. Marconi Simulation have been contracted to investigate the feasibility of using upwards of 100 processors, each capable of a peak of 30 MIPS to run a highly detailed RELAP5 model in real time, complete with specially written 3D core neutronics and balance of plant models. This paper describes the experience of using RELAP5 as an analyzer/simulator, and outlines the proposed methods and problems associated with parallel execution of RELAP5

  1. Aphasia for Morse code.

    Science.gov (United States)

    Wyler, A R; Ray, M W

    1986-03-01

    The ability to communicate by Morse code at high speed has, to our knowledge, not been localized within the cerebral cortex, but might be suspected as residing within the left (dominant) hemisphere. We report a case of a 54-year-old male who suffered a left temporal tip intracerebral hematoma and who temporarily lost his ability to communicate in Morse code, but who was minimally aphasic.

  2. Buckling rules in design codes: state of the art and future developments

    International Nuclear Information System (INIS)

    Turbat, A.; Meziere, Y.

    2001-01-01

    Buckling, which can affect structures like bars, beams and shells when they are submitted to compressive stresses, can lead to unacceptable deformations and ruptures. Consequently, main Design Codes, especially those used in nuclear industry, include rules and analysis methods in order to prevent this phenomenon. In this paper, a review of buckling rules and/or analysis methods existing in ASME, RCC-M, RCC-MR and European Recommendations is performed. Then, these rules and methods are applied to the case of a cylinder filled with water and submitted to a seismic loading and results are compared. In the last part, current developments of methods to analyse creep buckling and dynamic buckling which should come and complete RCC-MR soon are presented. (author)

  3. ADAPTION OF NONSTANDARD PIPING COMPONENTS INTO PRESENT DAY SEISMIC CODES

    Energy Technology Data Exchange (ETDEWEB)

    D. T. Clark; M. J. Russell; R. E. Spears; S. R. Jensen

    2009-07-01

    With spiraling energy demand and flat energy supply, there is a need to extend the life of older nuclear reactors. This sometimes requires that existing systems be evaluated to present day seismic codes. Older reactors built in the 1960s and early 1970s often used fabricated piping components that were code compliant during their initial construction time period, but are outside the standard parameters of present-day piping codes. There are several approaches available to the analyst in evaluating these non-standard components to modern codes. The simplest approach is to use the flexibility factors and stress indices for similar standard components with the assumption that the non-standard component’s flexibility factors and stress indices will be very similar. This approach can require significant engineering judgment. A more rational approach available in Section III of the ASME Boiler and Pressure Vessel Code, which is the subject of this paper, involves calculation of flexibility factors using finite element analysis of the non-standard component. Such analysis allows modeling of geometric and material nonlinearities. Flexibility factors based on these analyses are sensitive to the load magnitudes used in their calculation, load magnitudes that need to be consistent with those produced by the linear system analyses where the flexibility factors are applied. This can lead to iteration, since the magnitude of the loads produced by the linear system analysis depend on the magnitude of the flexibility factors. After the loading applied to the nonstandard component finite element model has been matched to loads produced by the associated linear system model, the component finite element model can then be used to evaluate the performance of the component under the loads with the nonlinear analysis provisions of the Code, should the load levels lead to calculated stresses in excess of Allowable stresses. This paper details the application of component-level finite

  4. PEAR code review

    International Nuclear Information System (INIS)

    De Wit, R.; Jamieson, T.; Lord, M.; Lafortune, J.F.

    1997-07-01

    As a necessary component in the continuous improvement and refinement of methodologies employed in the nuclear industry, regulatory agencies need to periodically evaluate these processes to improve confidence in results and ensure appropriate levels of safety are being achieved. The independent and objective review of industry-standard computer codes forms an essential part of this program. To this end, this work undertakes an in-depth review of the computer code PEAR (Public Exposures from Accidental Releases), developed by Atomic Energy of Canada Limited (AECL) to assess accidental releases from CANDU reactors. PEAR is based largely on the models contained in the Canadian Standards Association (CSA) N288.2-M91. This report presents the results of a detailed technical review of the PEAR code to identify any variations from the CSA standard and other supporting documentation, verify the source code, assess the quality of numerical models and results, and identify general strengths and weaknesses of the code. The version of the code employed in this review is the one which AECL intends to use for CANDU 9 safety analyses. (author)

  5. Rate-adaptive BCH codes for distributed source coding

    DEFF Research Database (Denmark)

    Salmistraro, Matteo; Larsen, Knud J.; Forchhammer, Søren

    2013-01-01

    This paper considers Bose-Chaudhuri-Hocquenghem (BCH) codes for distributed source coding. A feedback channel is employed to adapt the rate of the code during the decoding process. The focus is on codes with short block lengths for independently coding a binary source X and decoding it given its...... correlated side information Y. The proposed codes have been analyzed in a high-correlation scenario, where the marginal probability of each symbol, Xi in X, given Y is highly skewed (unbalanced). Rate-adaptive BCH codes are presented and applied to distributed source coding. Adaptive and fixed checking...

  6. Recommendations for codes and standards to be used for design and fabrication of high level waste canister

    International Nuclear Information System (INIS)

    Bermingham, A.J.; Booker, R.J.; Booth, H.R.; Ruehle, W.G.; Shevekov, S.; Silvester, A.G.; Tagart, S.W.; Thomas, J.A.; West, R.G.

    1978-01-01

    This study identifies codes, standards, and regulatory requirements for developing design criteria for high-level waste (HLW) canisters for commercial operation. It has been determined that the canister should be designed as a pressure vessel without provision for any overpressure protection type devices. It is recommended that the HLW canister be designed and fabricated to the requirements of the ASME Section III Code, Division 1 rules, for Code Class 3 components. Identification of other applicable industry and regulatory guides and standards are provided in this report. Requirements for the Design Specification are found in the ASME Section III Code. It is recommended that design verification be conducted principally with prototype testing which will encompass normal and accident service conditions during all phases of the canister life. Adequacy of existing quality assurance and licensing standards for the canister was investigated. One of the recommendations derived from this study is a requirement that the canister be N stamped. In addition, acceptance standards for the HLW waste should be established and the waste qualified to those standards before the canister is sealed. A preliminary investigation of use of an overpack for the canister has been made, and it is concluded that the use of an overpack, as an integral part of overall canister design, is undesirable, both from a design and economics standpoint. However, use of shipping cask liners and overpack type containers at the Federal repository may make the canister and HLW management safer and more cost effective. There are several possible concepts for canister closure design. These concepts can be adapted to the canister with or without an overpack. A remote seal weld closure is considered to be one of the most suitable closure methods; however, mechanical seals should also be investigated

  7. Polynomial weights and code constructions

    DEFF Research Database (Denmark)

    Massey, J; Costello, D; Justesen, Jørn

    1973-01-01

    polynomial included. This fundamental property is then used as the key to a variety of code constructions including 1) a simplified derivation of the binary Reed-Muller codes and, for any primepgreater than 2, a new extensive class ofp-ary "Reed-Muller codes," 2) a new class of "repeated-root" cyclic codes...... that are subcodes of the binary Reed-Muller codes and can be very simply instrumented, 3) a new class of constacyclic codes that are subcodes of thep-ary "Reed-Muller codes," 4) two new classes of binary convolutional codes with large "free distance" derived from known binary cyclic codes, 5) two new classes...... of long constraint length binary convolutional codes derived from2^r-ary Reed-Solomon codes, and 6) a new class ofq-ary "repeated-root" constacyclic codes with an algebraic decoding algorithm....

  8. SPECTRAL AMPLITUDE CODING OCDMA SYSTEMS USING ENHANCED DOUBLE WEIGHT CODE

    Directory of Open Access Journals (Sweden)

    F.N. HASOON

    2006-12-01

    Full Text Available A new code structure for spectral amplitude coding optical code division multiple access systems based on double weight (DW code families is proposed. The DW has a fixed weight of two. Enhanced double-weight (EDW code is another variation of a DW code family that can has a variable weight greater than one. The EDW code possesses ideal cross-correlation properties and exists for every natural number n. A much better performance can be provided by using the EDW code compared to the existing code such as Hadamard and Modified Frequency-Hopping (MFH codes. It has been observed that theoretical analysis and simulation for EDW is much better performance compared to Hadamard and Modified Frequency-Hopping (MFH codes.

  9. Some new ternary linear codes

    Directory of Open Access Journals (Sweden)

    Rumen Daskalov

    2017-07-01

    Full Text Available Let an $[n,k,d]_q$ code be a linear code of length $n$, dimension $k$ and minimum Hamming distance $d$ over $GF(q$. One of the most important problems in coding theory is to construct codes with optimal minimum distances. In this paper 22 new ternary linear codes are presented. Two of them are optimal. All new codes improve the respective lower bounds in [11].

  10. ACE - Manufacturer Identification Code (MID)

    Data.gov (United States)

    Department of Homeland Security — The ACE Manufacturer Identification Code (MID) application is used to track and control identifications codes for manufacturers. A manufacturer is identified on an...

  11. Algebraic and stochastic coding theory

    CERN Document Server

    Kythe, Dave K

    2012-01-01

    Using a simple yet rigorous approach, Algebraic and Stochastic Coding Theory makes the subject of coding theory easy to understand for readers with a thorough knowledge of digital arithmetic, Boolean and modern algebra, and probability theory. It explains the underlying principles of coding theory and offers a clear, detailed description of each code. More advanced readers will appreciate its coverage of recent developments in coding theory and stochastic processes. After a brief review of coding history and Boolean algebra, the book introduces linear codes, including Hamming and Golay codes.

  12. Optical coding theory with Prime

    CERN Document Server

    Kwong, Wing C

    2013-01-01

    Although several books cover the coding theory of wireless communications and the hardware technologies and coding techniques of optical CDMA, no book has been specifically dedicated to optical coding theory-until now. Written by renowned authorities in the field, Optical Coding Theory with Prime gathers together in one volume the fundamentals and developments of optical coding theory, with a focus on families of prime codes, supplemented with several families of non-prime codes. The book also explores potential applications to coding-based optical systems and networks. Learn How to Construct

  13. Speech coding code- excited linear prediction

    CERN Document Server

    Bäckström, Tom

    2017-01-01

    This book provides scientific understanding of the most central techniques used in speech coding both for advanced students as well as professionals with a background in speech audio and or digital signal processing. It provides a clear connection between the whys hows and whats thus enabling a clear view of the necessity purpose and solutions provided by various tools as well as their strengths and weaknesses in each respect Equivalently this book sheds light on the following perspectives for each technology presented Objective What do we want to achieve and especially why is this goal important Resource Information What information is available and how can it be useful and Resource Platform What kind of platforms are we working with and what are their capabilities restrictions This includes computational memory and acoustic properties and the transmission capacity of devices used. The book goes on to address Solutions Which solutions have been proposed and how can they be used to reach the stated goals and ...

  14. Comprehensive Report For Proposed Elevated Temperature Elastic Perfectly Plastic (EPP) Code Cases Representative Example Problems

    Energy Technology Data Exchange (ETDEWEB)

    Hollinger, Greg L. [Idaho National Lab. (INL), Idaho Falls, ID (United States)

    2014-06-01

    Background: The current rules in the nuclear section of the ASME Boiler and Pressure Vessel (B&PV) Code , Section III, Subsection NH for the evaluation of strain limits and creep-fatigue damage using simplified methods based on elastic analysis have been deemed inappropriate for Alloy 617 at temperatures above 1200F (650C)1. To address this issue, proposed code rules have been developed which are based on the use of elastic-perfectly plastic (E-PP) analysis methods and which are expected to be applicable to very high temperatures. The proposed rules for strain limits and creep-fatigue evaluation were initially documented in the technical literature 2, 3, and have been recently revised to incorporate comments and simplify their application. The revised code cases have been developed. Task Objectives: The goal of the Sample Problem task is to exercise these code cases through example problems to demonstrate their feasibility and, also, to identify potential corrections and improvements should problems be encountered. This will provide input to the development of technical background documents for consideration by the applicable B&PV committees considering these code cases for approval. This task has been performed by Hollinger and Pease of Becht Engineering Co., Inc., Nuclear Services Division and a report detailing the results of the E-PP analyses conducted on example problems per the procedures of the E-PP strain limits and creep-fatigue draft code cases is enclosed as Enclosure 1. Conclusions: The feasibility of the application of the E-PP code cases has been demonstrated through example problems that consist of realistic geometry (a nozzle attached to a semi-hemispheric shell with a circumferential weld) and load (pressure; pipe reaction load applied at the end of the nozzle, including axial and shear forces, bending and torsional moments; through-wall transient temperature gradient) and design and operating conditions (Levels A, B and C).

  15. Causas de óbitos entre asmáticos graves admitidos no Programa de Controle da Asma e da Rinite Alérgica na Bahia

    OpenAIRE

    Souza-Machado,Adelmir; Souza-Machado,Carolina; Silva,Daisy Freitas; Ponte,Eduardo Vieira; Cruz,Alvaro A.

    2007-01-01

    OBJETIVO: Descrever características demográficas e clínicas de asmáticos que apresentaram como desfecho a morte e relatar as condições que concorreram para o óbito entre admitidos no Programa de Controle da Asma e da Rinite Alérgica na Bahia (ProAR). MÉTODOS: Estudo observacional retrospectivo e descritivo. Foram coletadas informações de atestados de óbitos e prontuários médicos de 16 dos 930 portadores de asma grave acompanhados no ambulatório Central de Referência do ProAR entre dezembro de...

  16. Causas de óbitos entre asmáticos graves admitidos no Programa de Controle da Asma e da Rinite Alérgica na Bahia

    OpenAIRE

    Machado, Adelmir de Souza; Machado, Carolina Souza; Silva, Daisy Freitas; Ponte, Eduardo Vieira; Cruz Filho, Álvaro Augusto Souza da

    2007-01-01

    p. 372-379 OBJETIVO: Descrever características demográficas e clínicas de asmáticos que apresentaram como desfecho a morte e relatar as condições que concorreram para o óbito entre admitidos no Programa de Controle da Asma e da Rinite Alérgica na Bahia (ProAR). MÉTODOS: Estudo observacional retrospectivo e descritivo. Foram coletadas informações de atestados de óbitos e prontuários médicos de 16 dos 930 portadores de asma grave acompanhados no ambulatório Central de Referência do ProAR ...

  17. Removal of Antibiotics in Biological Wastewater Treatment Systems—A Critical Assessment Using the Activated Sludge Modeling Framework for Xenobiotics (ASM-X)

    DEFF Research Database (Denmark)

    Polesel, Fabio; Andersen, Henrik Rasmus; Trapp, Stefan

    2016-01-01

    Many scientific studies present removal efficiencies for pharmaceuticals in laboratory-, pilot-, and full-scale wastewater treatment plants, based on observations that may be impacted by theoretical and methodological approaches used. In this Critical Review, we evaluated factors influencing...... observed removal efficiencies of three antibiotics (sulfamethoxazole, ciprofloxacin, tetracycline) in pilot- and full-scale biological treatment systems. Factors assessed include (i) retransformation to parent pharmaceuticals from e.g., conjugated metabolites and analogues, (ii) solid retention time (SRT......), (iii) fractions sorbed onto solids, and (iv) dynamics in influent and effluent loading. A recently developed methodology was used, relying on the comparison of removal efficiency predictions (obtained with the Activated Sludge Model for Xenobiotics (ASM-X)) with representative measured data from...

  18. Evaluation of the ICET Test Stand to Assess the Performance of a Range of Ceramic Media Filter Elements in Support of ASME AG-1 Subsection FO

    Energy Technology Data Exchange (ETDEWEB)

    Schemmel, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2017-04-26

    High Efficiency Particulate Air (HEPA) filters are defined as extended-medium, dry-type filters with: (1) a minimum particle removal efficiency of no less than 99.97 percent for 0.3 micrometer particles, (2) a maximum, clean resistance of 1.0 inch water column (in. WC) when operated at 1,000 cubic feet per minute (CFM), and (3) a rigid casing that extends the full depth of the medium. Specifically, ceramic media HEPA filters provide better performance at elevated temperatures, are moisture resistant and nonflammable, can perform their function if wetted and exposed to greater pressures, and can be cleaned and reused. This paper describes the modification and design of a large scale test stand which properly evaluates the filtration characteristics of a range of ceramic media filters challenged with a nuclear aerosol agent in order to develop Section FO of ASME AG-1.

  19. Critical Appraisal of Microbiology Guidelines Endorsed by two Professional Organisations: Société Française De Microbiologie (SFM) and American Society of Microbiology (ASM).

    Science.gov (United States)

    Fonfrède, Michèle; Couaillac, Jean Paul; Augereau, Christine; Lepargneur, Jean Pierre; Watine, Joseph

    2012-07-01

    Medical practice guidelines (GLs) being tools that are mainly designed to evaluate medical professionals, it sounds logical, and fair, that professionals should in turn evaluate GLs. Microbiology being a medical discipline, we used the AGREE instrument, i.e. an established evaluation tool for GLs, in order to evaluate the quality of two major microbiology guidelines, i.e. the SFM GLs and the ASM GLs). Both guidelines remain sub-optimal in their levels of quality, and obtain scores that are not very different from the average scores obtained by many other guidelines in various medical disciplines. We therefore believe that both guidelines need to be modified before they can be recommended without provisos. A higher degree of multi-disciplinary work, including a more formal implication of methodologists, as well as of infectious disease clinicians, and of economists, might perhaps enable future editions of these guidelines to reach higher levels of quality.

  20. Dynamic experiments with high bisphenol-A concentrations modelled with an ASM model extended to include a separate XOC degrading microorganism.

    Science.gov (United States)

    Lindblom, Erik; Press-Kristensen, Kåre; Vanrolleghem, Peter A; Mikkelsen, Peter S; Henze, Mogens

    2009-07-01

    The perspective of this work is to develop a model, which can be used to better understand and optimize wastewater treatment plants that are able to remove xenobiotic organic compounds (XOCs) in combination with removal of traditional pollutants. Results from dynamic experiments conducted with the endocrine disrupting XOC bisphenol-A (BPA) in an activated sludge process with real wastewater were used to hypothesize an ASM-based process model including aerobic growth of a specific BPA-degrading microorganism and sorption of BPA to sludge. A parameter estimation method was developed, which simultaneously utilizes steady-state background concentrations and dynamic step response data, as well as conceptual simplifications of the plant configuration. Validation results show that biodegradation of BPA is sensitive to operational conditions before and during the experiment and that the proposed model structure is capable of capturing important characteristics of the observed BPA removal, thus increasing the potential for generalizing knowledge obtained from plant specific experiments.

  1. Spatially coded backscatter radiography

    International Nuclear Information System (INIS)

    Thangavelu, S.; Hussein, E.M.A.

    2007-01-01

    Conventional radiography requires access to two opposite sides of an object, which makes it unsuitable for the inspection of extended and/or thick structures (airframes, bridges, floors etc.). Backscatter imaging can overcome this problem, but the indications obtained are difficult to interpret. This paper applies the coded aperture technique to gamma-ray backscatter-radiography in order to enhance the detectability of flaws. This spatial coding method involves the positioning of a mask with closed and open holes to selectively permit or block the passage of radiation. The obtained coded-aperture indications are then mathematically decoded to detect the presence of anomalies. Indications obtained from Monte Carlo calculations were utilized in this work to simulate radiation scattering measurements. These simulated measurements were used to investigate the applicability of this technique to the detection of flaws by backscatter radiography

  2. Aztheca Code; Codigo Aztheca

    Energy Technology Data Exchange (ETDEWEB)

    Quezada G, S.; Espinosa P, G. [Universidad Autonoma Metropolitana, Unidad Iztapalapa, San Rafael Atlixco No. 186, Col. Vicentina, 09340 Ciudad de Mexico (Mexico); Centeno P, J.; Sanchez M, H., E-mail: sequga@gmail.com [UNAM, Facultad de Ingenieria, Ciudad Universitaria, Circuito Exterior s/n, 04510 Ciudad de Mexico (Mexico)

    2017-09-15

    This paper presents the Aztheca code, which is formed by the mathematical models of neutron kinetics, power generation, heat transfer, core thermo-hydraulics, recirculation systems, dynamic pressure and level models and control system. The Aztheca code is validated with plant data, as well as with predictions from the manufacturer when the reactor operates in a stationary state. On the other hand, to demonstrate that the model is applicable during a transient, an event occurred in a nuclear power plant with a BWR reactor is selected. The plant data are compared with the results obtained with RELAP-5 and the Aztheca model. The results show that both RELAP-5 and the Aztheca code have the ability to adequately predict the behavior of the reactor. (Author)

  3. Code query by example

    Science.gov (United States)

    Vaucouleur, Sebastien

    2011-02-01

    We introduce code query by example for customisation of evolvable software products in general and of enterprise resource planning systems (ERPs) in particular. The concept is based on an initial empirical study on practices around ERP systems. We motivate our design choices based on those empirical results, and we show how the proposed solution helps with respect to the infamous upgrade problem: the conflict between the need for customisation and the need for upgrade of ERP systems. We further show how code query by example can be used as a form of lightweight static analysis, to detect automatically potential defects in large software products. Code query by example as a form of lightweight static analysis is particularly interesting in the context of ERP systems: it is often the case that programmers working in this field are not computer science specialists but more of domain experts. Hence, they require a simple language to express custom rules.

  4. Coded Splitting Tree Protocols

    DEFF Research Database (Denmark)

    Sørensen, Jesper Hemming; Stefanovic, Cedomir; Popovski, Petar

    2013-01-01

    This paper presents a novel approach to multiple access control called coded splitting tree protocol. The approach builds on the known tree splitting protocols, code structure and successive interference cancellation (SIC). Several instances of the tree splitting protocol are initiated, each...... instance is terminated prematurely and subsequently iterated. The combined set of leaves from all the tree instances can then be viewed as a graph code, which is decodable using belief propagation. The main design problem is determining the order of splitting, which enables successful decoding as early...... as possible. Evaluations show that the proposed protocol provides considerable gains over the standard tree splitting protocol applying SIC. The improvement comes at the expense of an increased feedback and receiver complexity....

  5. Revised SRAC code system

    International Nuclear Information System (INIS)

    Tsuchihashi, Keichiro; Ishiguro, Yukio; Kaneko, Kunio; Ido, Masaru.

    1986-09-01

    Since the publication of JAERI-1285 in 1983 for the preliminary version of the SRAC code system, a number of additions and modifications to the functions have been made to establish an overall neutronics code system. Major points are (1) addition of JENDL-2 version of data library, (2) a direct treatment of doubly heterogeneous effect on resonance absorption, (3) a generalized Dancoff factor, (4) a cell calculation based on the fixed boundary source problem, (5) the corresponding edit required for experimental analysis and reactor design, (6) a perturbation theory calculation for reactivity change, (7) an auxiliary code for core burnup and fuel management, etc. This report is a revision of the users manual which consists of the general description, input data requirements and their explanation, detailed information on usage, mathematics, contents of libraries and sample I/O. (author)

  6. Percepção da dispneia na crise asmática pediátrica pelos pacientes e responsáveis

    Directory of Open Access Journals (Sweden)

    Ana Alice Amaral Ibiapina Parente

    2011-12-01

    Full Text Available OBJETIVO: Avaliar a correlação entre a percepção da dispneia durante uma crise de asma leve a moderada, por meio da escala modificada de Borg, com a medida do pico de fluxo expiratório (PFE. MÉTODOS: Estudo transversal de crianças e adolescentes que procuraram a emergência pediátrica devido a crise asmática, com dados coletados de julho de 2005 a junho de 2006. Foram registrados dados demográficos. Pacientes e seus responsáveis foram solicitados a graduar, individualmente, a dispneia do paciente por meio da escala modificada de Borg e, posteriormente, foi avaliada a medida do PFE. RESULTADOS: Foram avaliados 181 pacientes asmáticos, com idade média de 7,2 (±2,4 anos (4-12. A mãe procurou atendimento médico em 83,4% (151/181. Os sintomas incluíram tosse, em 68,5% (124/181, dispneia, em 47,0% (85/181, e sibilância, em 12,7% (23/181. Trinta e seis por cento (65/181 apresentavam crise leve, e 64,1% (116/181, moderada. Correlação negativa significativa foi evidenciada entre a percepção dos responsáveis e dos pacientes com dispneia e a medida do PFE dos pacientes (percentual previsto; r s = -0,240 e r s = -0,385, respectivamente. CONCLUSÃO: Pacientes e responsáveis demonstraram percepção limitada da gravidade da dispneia do paciente, evidenciando a necessidade de monitorar medidas objetivas, como a medida do PFE e o desenvolvimento de melhores meios de avaliação da dispneia.

  7. Fatores de risco para consultas em pronto-socorro por crianças asmáticas no Sul do Brasil

    Directory of Open Access Journals (Sweden)

    Chatkin Moema

    2000-01-01

    Full Text Available OBJETIVOS: Traçar um perfil das crianças asmáticas do município de Pelotas, RS, conhecer o manejo da doença e os fatores de risco associados a consultas em pronto-socorro, motivadas por asma. MÉTODOS: Estudo transversal aninhado a um estudo de coorte, realizado na área urbana de Pelotas, cidade de médio porte do Sul do Brasil. Participaram 981 crianças de 4-5 anos, pertencentes à coorte de 1993. RESULTADOS: A prevalência de asma encontrada na amostra estudada foi de 25,4%. A morbidade por asma foi elevada: 31% das crianças asmáticas haviam procurado o pronto-socorro no último ano, 57% tinham consultado médico e 26%, de 1 a 4 anos, foram internadas por asma. Na análise geral, escolaridade e renda familiar baixas associaram-se com consultas em pronto-socorro (RO=4,1 para 0 a 4 anos de escolaridade e RO=6,5 para menos de 1 salário-mínimo. Dormir em quartos com 3 ou mais pessoas também mostrou-se associado (RO=2,2, bem como severidade das crises (RO=2,7, uso de medicamentos para asma no último ano (RO=1,9 e internações por asma (RO=3,0. CONCLUSÕES: A prevalência de asma entre crianças pré-escolares em Pelotas é alta, levando a grande morbidade. Encontraram-se como fatores preditores de consultas em pronto-socorro por asma, após análise multivariada, a baixa escolaridade das mães, severidade das crises e internação por asma.

  8. Graph Codes with Reed-Solomon Component Codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Justesen, Jørn

    2006-01-01

    We treat a specific case of codes based on bipartite expander graphs coming from finite geometries. The code symbols are associated with the branches and the symbols connected to a given node are restricted to be codewords in a Reed-Solomon code. We give results on the parameters of the codes...

  9. Visualizing code and coverage changes for code review

    NARCIS (Netherlands)

    Oosterwaal, Sebastiaan; van Deursen, A.; De Souza Coelho, R.; Sawant, A.A.; Bacchelli, A.

    2016-01-01

    One of the tasks of reviewers is to verify that code modifications are well tested. However, current tools offer little support in understanding precisely how changes to the code relate to changes to the tests. In particular, it is hard to see whether (modified) test code covers the changed code.

  10. Principles of speech coding

    CERN Document Server

    Ogunfunmi, Tokunbo

    2010-01-01

    It is becoming increasingly apparent that all forms of communication-including voice-will be transmitted through packet-switched networks based on the Internet Protocol (IP). Therefore, the design of modern devices that rely on speech interfaces, such as cell phones and PDAs, requires a complete and up-to-date understanding of the basics of speech coding. Outlines key signal processing algorithms used to mitigate impairments to speech quality in VoIP networksOffering a detailed yet easily accessible introduction to the field, Principles of Speech Coding provides an in-depth examination of the

  11. Scrum Code Camps

    DEFF Research Database (Denmark)

    Pries-Heje, Jan; Pries-Heje, Lene; Dahlgaard, Bente

    2013-01-01

    A classic way to choose a supplier is through a bidding process where tenders from competing companies are evaluated in relation to the customer’s requirements. If the customer wants to hire an agile software developing team instead of buying a software product, a new approach for comparing tenders...... is required. In this paper we present the design of such a new approach, the Scrum Code Camp, which can be used to assess agile team capability in a transparent and consistent way. A design science research approach is used to analyze properties of two instances of the Scrum Code Camp where seven agile teams...

  12. Supervised Convolutional Sparse Coding

    KAUST Repository

    Affara, Lama Ahmed

    2018-04-08

    Convolutional Sparse Coding (CSC) is a well-established image representation model especially suited for image restoration tasks. In this work, we extend the applicability of this model by proposing a supervised approach to convolutional sparse coding, which aims at learning discriminative dictionaries instead of purely reconstructive ones. We incorporate a supervised regularization term into the traditional unsupervised CSC objective to encourage the final dictionary elements to be discriminative. Experimental results show that using supervised convolutional learning results in two key advantages. First, we learn more semantically relevant filters in the dictionary and second, we achieve improved image reconstruction on unseen data.

  13. CONCEPT computer code

    International Nuclear Information System (INIS)

    Delene, J.

    1984-01-01

    CONCEPT is a computer code that will provide conceptual capital investment cost estimates for nuclear and coal-fired power plants. The code can develop an estimate for construction at any point in time. Any unit size within the range of about 400 to 1300 MW electric may be selected. Any of 23 reference site locations across the United States and Canada may be selected. PWR, BWR, and coal-fired plants burning high-sulfur and low-sulfur coal can be estimated. Multiple-unit plants can be estimated. Costs due to escalation/inflation and interest during construction are calculated

  14. Decoding Codes on Graphs

    Indian Academy of Sciences (India)

    lowing function is maximized,. This kind of decoding strategy is called the maximum a posteriori probability (MAP) decoding strategy as it attempts to estimate each symbol of the codeword that ..... gate the effects of packet loss over digital networks. Un- doubtedly other applications will use these codes in the years to come.

  15. New code of conduct

    CERN Multimedia

    Laëtitia Pedroso

    2010-01-01

    During his talk to the staff at the beginning of the year, the Director-General mentioned that a new code of conduct was being drawn up. What exactly is it and what is its purpose? Anne-Sylvie Catherin, Head of the Human Resources (HR) Department, talked to us about the whys and wherefores of the project.   Drawing by Georges Boixader from the cartoon strip “The World of Particles” by Brian Southworth. A code of conduct is a general framework laying down the behaviour expected of all members of an organisation's personnel. “CERN is one of the very few international organisations that don’t yet have one", explains Anne-Sylvie Catherin. “We have been thinking about introducing a code of conduct for a long time but lacked the necessary resources until now”. The call for a code of conduct has come from different sources within the Laboratory. “The Equal Opportunities Advisory Panel (read also the "Equal opportuni...

  16. CERN Code of Conduct

    CERN Document Server

    Department, HR

    2010-01-01

    The Code is intended as a guide in helping us, as CERN contributors, to understand how to conduct ourselves, treat others and expect to be treated. It is based around the five core values of the Organization. We should all become familiar with it and try to incorporate it into our daily life at CERN.

  17. Error Correcting Codes

    Indian Academy of Sciences (India)

    focused pictures of Triton, Neptune's largest moon. This great feat was in no small measure due to the fact that the sophisticated communication system on Voyager had an elaborate error correcting scheme built into it. At Jupiter and Saturn, a convolutional code was used to enhance the reliability of transmission, and at ...

  18. Nuclear safety code study

    Energy Technology Data Exchange (ETDEWEB)

    Hu, H.H.; Ford, D.; Le, H.; Park, S.; Cooke, K.L.; Bleakney, T.; Spanier, J.; Wilburn, N.P.; O' Reilly, B.; Carmichael, B.

    1981-01-01

    The objective is to analyze an overpower accident in an LMFBR. A simplified model of the primary coolant loop was developed in order to understand the instabilities encountered with the MELT III and SAS codes. The computer programs were translated for switching to the IBM 4331. Numerical methods were investigated for solving the neutron kinetics equations; the Adams and Gear methods were compared. (DLC)

  19. Student Dress Codes.

    Science.gov (United States)

    Uerling, Donald F.

    School officials see a need for regulations that prohibit disruptive and inappropriate forms of expression and attire; students see these regulations as unwanted restrictions on their freedom. This paper reviews court litigation involving constitutional limitations on school authority, dress and hair codes, state law constraints, and school…

  20. Differential pulse code modulation

    Science.gov (United States)

    Herman, C. F. (Inventor)

    1976-01-01

    A differential pulse code modulation (DPCM) encoding and decoding method is described along with an apparatus which is capable of transmission with minimum bandwidth. The apparatus is not affected by data transition density, requires no direct current (DC) response of the transmission link, and suffers from minimal ambiguity in resolution of the digital data.

  1. Error Correcting Codes

    Indian Academy of Sciences (India)

    syndrome is an indicator of underlying disease. Here too, a non zero syndrome is an indication that something has gone wrong during transmission. SERIES I ARTICLE. The first matrix on the left hand side is called the parity check matrix H. Thus every codeword c satisfies the equation o o. HcT = o o. Therefore the code can ...

  2. Focusing Automatic Code Inspections

    NARCIS (Netherlands)

    Boogerd, C.J.

    2010-01-01

    Automatic Code Inspection tools help developers in early detection of defects in software. A well-known drawback of many automatic inspection approaches is that they yield too many warnings and require a clearer focus. In this thesis, we provide such focus by proposing two methods to prioritize

  3. Reliability and code level

    NARCIS (Netherlands)

    Kasperski, M.; Geurts, C.P.W.

    2005-01-01

    The paper describes the work of the IAWE Working Group WBG - Reliability and Code Level, one of the International Codification Working Groups set up at ICWE10 in Copenhagen. The following topics are covered: sources of uncertainties in the design wind load, appropriate design target values for the

  4. Broadcast Coded Slotted ALOHA

    DEFF Research Database (Denmark)

    Ivanov, Mikhail; Brännström, Frederik; Graell i Amat, Alexandre

    2016-01-01

    We propose an uncoordinated medium access control (MAC) protocol, called all-to-all broadcast coded slotted ALOHA (B-CSA) for reliable all-to-all broadcast with strict latency constraints. In B-CSA, each user acts as both transmitter and receiver in a half-duplex mode. The half-duplex mode gives...

  5. Ready, steady… Code!

    CERN Multimedia

    Anaïs Schaeffer

    2013-01-01

    This summer, CERN took part in the Google Summer of Code programme for the third year in succession. Open to students from all over the world, this programme leads to very successful collaborations for open source software projects.   Image: GSoC 2013. Google Summer of Code (GSoC) is a global programme that offers student developers grants to write code for open-source software projects. Since its creation in 2005, the programme has brought together some 6,000 students from over 100 countries worldwide. The students selected by Google are paired with a mentor from one of the participating projects, which can be led by institutes, organisations, companies, etc. This year, CERN PH Department’s SFT (Software Development for Experiments) Group took part in the GSoC programme for the third time, submitting 15 open-source projects. “Once published on the Google Summer for Code website (in April), the projects are open to applications,” says Jakob Blomer, one of the o...

  6. (Almost) practical tree codes

    KAUST Repository

    Khina, Anatoly

    2016-08-15

    We consider the problem of stabilizing an unstable plant driven by bounded noise over a digital noisy communication link, a scenario at the heart of networked control. To stabilize such a plant, one needs real-time encoding and decoding with an error probability profile that decays exponentially with the decoding delay. The works of Schulman and Sahai over the past two decades have developed the notions of tree codes and anytime capacity, and provided the theoretical framework for studying such problems. Nonetheless, there has been little practical progress in this area due to the absence of explicit constructions of tree codes with efficient encoding and decoding algorithms. Recently, linear time-invariant tree codes were proposed to achieve the desired result under maximum-likelihood decoding. In this work, we take one more step towards practicality, by showing that these codes can be efficiently decoded using sequential decoding algorithms, up to some loss in performance (and with some practical complexity caveats). We supplement our theoretical results with numerical simulations that demonstrate the effectiveness of the decoder in a control system setting.

  7. Physical layer network coding

    DEFF Research Database (Denmark)

    Fukui, Hironori; Popovski, Petar; Yomo, Hiroyuki

    2014-01-01

    Physical layer network coding (PLNC) has been proposed to improve throughput of the two-way relay channel, where two nodes communicate with each other, being assisted by a relay node. Most of the works related to PLNC are focused on a simple three-node model and they do not take into account...

  8. Corporate governance through codes

    NARCIS (Netherlands)

    Haxhi, I.; Aguilera, R.V.; Vodosek, M.; den Hartog, D.; McNett, J.M.

    2014-01-01

    The UK's 1992 Cadbury Report defines corporate governance (CG) as the system by which businesses are directed and controlled. CG codes are a set of best practices designed to address deficiencies in the formal contracts and institutions by suggesting prescriptions on the preferred role and

  9. Ptolemy Coding Style

    Science.gov (United States)

    2014-09-05

    because this would combine Ptolemy II with the GPL’d code and thus encumber Ptolemy II with the GPL. Another GNU license is the GNU Library General...permission on the source.eecs.berkeley.edu repositories, then use your local repository. bash-3.2$ svn co svn+ ssh ://source.eecs.berkeley.edu/chess

  10. Accumulate Repeat Accumulate Coded Modulation

    Science.gov (United States)

    Abbasfar, Aliazam; Divsalar, Dariush; Yao, Kung

    2004-01-01

    In this paper we propose an innovative coded modulation scheme called 'Accumulate Repeat Accumulate Coded Modulation' (ARA coded modulation). This class of codes can be viewed as serial turbo-like codes, or as a subclass of Low Density Parity Check (LDPC) codes that are combined with high level modulation. Thus at the decoder belief propagation can be used for iterative decoding of ARA coded modulation on a graph, provided a demapper transforms the received in-phase and quadrature samples to reliability of the bits.

  11. Causation, constructors and codes.

    Science.gov (United States)

    Hofmeyr, Jan-Hendrik S

    2018-02-01

    Relational biology relies heavily on the enriched understanding of causal entailment that Robert Rosen's formalisation of Aristotle's four causes has made possible, although to date efficient causes and the rehabilitation of final cause have been its main focus. Formal cause has been paid rather scant attention, but, as this paper demonstrates, is crucial to our understanding of many types of processes, not necessarily biological. The graph-theoretic relational diagram of a mapping has played a key role in relational biology, and the first part of the paper is devoted to developing an explicit representation of formal cause in the diagram and how it acts in combination with efficient cause to form a mapping. I then use these representations to show how Von Neumann's universal constructor can be cast into a relational diagram in a way that avoids the logical paradox that Rosen detected in his own representation of the constructor in terms of sets and mappings. One aspect that was absent from both Von Neumann's and Rosen's treatments was the necessity of a code to translate the description (the formal cause) of the automaton to be constructed into the construction process itself. A formal definition of codes in general, and organic codes in particular, allows the relational diagram to be extended so as to capture this translation of formal cause into process. The extended relational diagram is used to exemplify causal entailment in a diverse range of processes, such as enzyme action, construction of automata, communication through the Morse code, and ribosomal polypeptide synthesis through the genetic code. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Conformity of nuclear construction codes with the requirements of the French order dated December 12, 2005 related to nuclear pressure equipment; Conformite des codes de construction nucleaires avec les exigences de l'arrete du 12 decembre 2005 relatif aux equipements sous pression nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Grandemange, J.M.; Renaut, P. [Areva-NP, Tour AREVA, 92084 - Paris La Defense cedex, (France); Paris, D. [EDF-Ceidre 2 rue Ampere - 93206 SAINT-DENIS Cedex (France); Faidy, C. [EDF-Septen 12/14, Avenue Dutrievoz 69628 Villeurbanne Cedex (France)

    2007-07-01

    The French Decree dated December 13, 1999 transposing the Pressure Equipment Directive (PED) has replaced the fundamental texts on which up to now the regulation for pressure equipment important for the safety of nuclear reactors was also founded. By a Ministerial Order - called 'ESPN Order' - dated December 12, 2005, a new regulation has been issued for nuclear pressure equipment. This text makes reference to the Decree transposing the PED while completing these provisions by supplementary requirements having the objective to provide a very high level of integrity guarantee for equipments which are the most important for safety, and to cover the prevention of radioactive release risks. These regulatory evolutions are presented in the Plenary Session of the ESOPE conference. Referencing the Decree and thus the PED, and including specific provisions, the Ministerial Order implies that the Manufacturers update their documents and, if necessary, their prescriptions in the following two domains: - that of the conformity of Codes and Standards used, generally inspired from the ASME Code Section III, with the essential safety requirements of the PED, - that of the respect of the complementary provisions brought by the ESPN Order. This paper presents the more significant conclusions of this work and the resulting amendments of the RCC-M Code, introduced by the 2007 addendum to that Code. The analysis will lead to specify the same type of complementary requirements to Code when a manufacturer wishes to use the German KTA Rules or the ASME Code Section III. (authors) [French] Le decret du 13 decembre 1999 transposant la directive europeenne (DESP) relative aux equipements sous pression a remplace les textes fondamentaux sur lesquels se fondait egalement jusque la la reglementation des appareils a pression importants pour la surete des reacteurs nucleaires. Par arrete - dit 'arrete ESPN' - du 12 decembre 2005, une nouvelle reglementation a ete dictee. Ce

  13. Structural design codes: Strain-life method and fatigue damage estimation for ITER

    International Nuclear Information System (INIS)

    Karditsas, P.J.

    1996-01-01

    A preferred route is suggested for implementing the design rules and requirements of the design codes for the International Thermonuclear Experimental Reactor (ITER), such as ASME and RCC-MR, and for preliminarily assessing which of the in-service loading conditions inflicts the greatest damage on the structure. Some of the relevant design code rules and constraints are presented, and lifetime and fatigue damage, with some data on fatigue life for Type 316 stainless steel, are predicted. A design curve for strain range versus the number of cycles to failure is presented, including the effect of neutron damage on the material. An example calculation is performed on a first-wall section, and preliminary estimation of the fatigue usage factor is presented. One must observe caution when assessing the results because of the assumptions made in performing the calculations. The results, however, indicate that parts of the component are in the low-cycle fatigue region of operation, which thus supports the use of strain-life methods. The load-controlled stress limit approach of the existing codes leads to difficulties with in-service loading and component categorization, whereas the strain-deformation limit approach may lead to difficulties in calculations. The conclusion is that the load-controlled approach shifts the emphasis to the regulator and the licensing body, whereas the strain-deformation approach shifts the emphasis to the designer and the structural analyst. 11 refs., 7 figs., 2 tabs

  14. Entanglement-assisted quantum MDS codes constructed from negacyclic codes

    Science.gov (United States)

    Chen, Jianzhang; Huang, Yuanyuan; Feng, Chunhui; Chen, Riqing

    2017-12-01

    Recently, entanglement-assisted quantum codes have been constructed from cyclic codes by some scholars. However, how to determine the number of shared pairs required to construct entanglement-assisted quantum codes is not an easy work. In this paper, we propose a decomposition of the defining set of negacyclic codes. Based on this method, four families of entanglement-assisted quantum codes constructed in this paper satisfy the entanglement-assisted quantum Singleton bound, where the minimum distance satisfies q+1 ≤ d≤ n+2/2. Furthermore, we construct two families of entanglement-assisted quantum codes with maximal entanglement.

  15. Codes of Good Governance

    DEFF Research Database (Denmark)

    Beck Jørgensen, Torben; Sørensen, Ditte-Lene

    2013-01-01

    Good governance is a broad concept used by many international organizations to spell out how states or countries should be governed. Definitions vary, but there is a clear core of common public values, such as transparency, accountability, effectiveness, and the rule of law. It is quite likely......, however, that national views of good governance reflect different political cultures and institutional heritages. Fourteen national codes of conduct are analyzed. The findings suggest that public values converge and that they match model codes from the United Nations and the European Council as well...... as conceptions of good governance from other international organizations. While values converge, they are balanced and communicated differently, and seem to some extent to be translated into the national cultures. The set of global public values derived from this analysis include public interest, regime dignity...

  16. Coding isotropic images

    Science.gov (United States)

    Oneal, J. B., Jr.; Natarajan, T. R.

    1976-01-01

    Rate distortion functions for two-dimensional homogeneous isotropic images are compared with the performance of 5 source encoders designed for such images. Both unweighted and frequency weighted mean square error distortion measures are considered. The coders considered are differential PCM (DPCM) using six previous samples in the prediction, herein called 6 pel (picutre element) DPCM; simple DPCM using single sample prediction; 6 pel DPCM followed by entropy coding; 8 x 8 discrete cosine transform coder, and 4 x 4 Hadamard transform coder. Other transform coders were studied and found to have about the same performance as the two transform coders above. With the mean square error distortion measure DPCM with entropy coding performed best. The relative performance of the coders changes slightly when the distortion measure is frequency weighted mean square error. The performance of all the coders was separated by only about 4 dB.

  17. Efficient convolutional sparse coding

    Energy Technology Data Exchange (ETDEWEB)

    Wohlberg, Brendt

    2017-06-20

    Computationally efficient algorithms may be applied for fast dictionary learning solving the convolutional sparse coding problem in the Fourier domain. More specifically, efficient convolutional sparse coding may be derived within an alternating direction method of multipliers (ADMM) framework that utilizes fast Fourier transforms (FFT) to solve the main linear system in the frequency domain. Such algorithms may enable a significant reduction in computational cost over conventional approaches by implementing a linear solver for the most critical and computationally expensive component of the conventional iterative algorithm. The theoretical computational cost of the algorithm may be reduced from O(M.sup.3N) to O(MN log N), where N is the dimensionality of the data and M is the number of elements in the dictionary. This significant improvement in efficiency may greatly increase the range of problems that can practically be addressed via convolutional sparse representations.

  18. Computer code FIT

    International Nuclear Information System (INIS)

    Rohmann, D.; Koehler, T.

    1987-02-01

    This is a description of the computer code FIT, written in FORTRAN-77 for a PDP 11/34. FIT is an interactive program to decude position, width and intensity of lines of X-ray spectra (max. length of 4K channels). The lines (max. 30 lines per fit) may have Gauss- or Voigt-profile, as well as exponential tails. Spectrum and fit can be displayed on a Tektronix terminal. (orig.) [de

  19. Status of MARS Code

    Energy Technology Data Exchange (ETDEWEB)

    N.V. Mokhov

    2003-04-09

    Status and recent developments of the MARS 14 Monte Carlo code system for simulation of hadronic and electromagnetic cascades in shielding, accelerator and detector components in the energy range from a fraction of an electronvolt up to 100 TeV are described. these include physics models both in strong and electromagnetic interaction sectors, variance reduction techniques, residual dose, geometry, tracking, histograming. MAD-MARS Beam Line Build and Graphical-User Interface.

  20. Cracking the Gender Codes

    DEFF Research Database (Denmark)

    Rennison, Betina Wolfgang

    2016-01-01

    Why do men continue to fill most of the senior executive positions and seats in the board of directors in Western corporations? Almost everyone agrees that diversity is good, many women are coming down the pipeline, and companies, states and international organizations and institutions have done...... in leadership management, we must become more aware and take advantage of this complexity. We must crack the codes in order to crack the curve....

  1. Hydra Code Release

    OpenAIRE

    Couchman, H. M. P.; Pearce, F. R.; Thomas, P. A.

    1996-01-01

    Comment: A new version of the AP3M-SPH code, Hydra, is now available as a tar file from the following sites; http://coho.astro.uwo.ca/pub/hydra/hydra.html , http://star-www.maps.susx.ac.uk/~pat/hydra/hydra.html . The release now also contains a cosmological initial conditions generator, documentation, an installation guide and installation tests. A LaTex version of the documentation is included here

  2. Tokamak simulation code manual

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Moon Kyoo; Oh, Byung Hoon; Hong, Bong Keun; Lee, Kwang Won [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

    1995-01-01

    The method to use TSC (Tokamak Simulation Code) developed by Princeton plasma physics laboratory is illustrated. In KT-2 tokamak, time dependent simulation of axisymmetric toroidal plasma and vertical stability have to be taken into account in design phase using TSC. In this report physical modelling of TSC are described and examples of application in JAERI and SERI are illustrated, which will be useful when TSC is installed KAERI computer system. (Author) 15 refs., 6 figs., 3 tabs.

  3. Tokamak simulation code manual

    International Nuclear Information System (INIS)

    Chung, Moon Kyoo; Oh, Byung Hoon; Hong, Bong Keun; Lee, Kwang Won

    1995-01-01

    The method to use TSC (Tokamak Simulation Code) developed by Princeton plasma physics laboratory is illustrated. In KT-2 tokamak, time dependent simulation of axisymmetric toroidal plasma and vertical stability have to be taken into account in design phase using TSC. In this report physical modelling of TSC are described and examples of application in JAERI and SERI are illustrated, which will be useful when TSC is installed KAERI computer system. (Author) 15 refs., 6 figs., 3 tabs

  4. MELCOR computer code manuals

    Energy Technology Data Exchange (ETDEWEB)

    Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L. [Sandia National Labs., Albuquerque, NM (United States); Hodge, S.A.; Hyman, C.R.; Sanders, R.L. [Oak Ridge National Lab., TN (United States)

    1995-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR`s phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package.

  5. Bar coded retroreflective target

    Science.gov (United States)

    Vann, Charles S.

    2000-01-01

    This small, inexpensive, non-contact laser sensor can detect the location of a retroreflective target in a relatively large volume and up to six degrees of position. The tracker's laser beam is formed into a plane of light which is swept across the space of interest. When the beam illuminates the retroreflector, some of the light returns to the tracker. The intensity, angle, and time of the return beam is measured to calculate the three dimensional location of the target. With three retroreflectors on the target, the locations of three points on the target are measured, enabling the calculation of all six degrees of target position. Until now, devices for three-dimensional tracking of objects in a large volume have been heavy, large, and very expensive. Because of the simplicity and unique characteristics of this tracker, it is capable of three-dimensional tracking of one to several objects in a large volume, yet it is compact, light-weight, and relatively inexpensive. Alternatively, a tracker produces a diverging laser beam which is directed towards a fixed position, and senses when a retroreflective target enters the fixed field of view. An optically bar coded target can be read by the tracker to provide information about the target. The target can be formed of a ball lens with a bar code on one end. As the target moves through the field, the ball lens causes the laser beam to scan across the bar code.

  6. MELCOR computer code manuals

    International Nuclear Information System (INIS)

    Summers, R.M.; Cole, R.K. Jr.; Smith, R.C.; Stuart, D.S.; Thompson, S.L.; Hodge, S.A.; Hyman, C.R.; Sanders, R.L.

    1995-03-01

    MELCOR is a fully integrated, engineering-level computer code that models the progression of severe accidents in light water reactor nuclear power plants. MELCOR is being developed at Sandia National Laboratories for the U.S. Nuclear Regulatory Commission as a second-generation plant risk assessment tool and the successor to the Source Term Code Package. A broad spectrum of severe accident phenomena in both boiling and pressurized water reactors is treated in MELCOR in a unified framework. These include: thermal-hydraulic response in the reactor coolant system, reactor cavity, containment, and confinement buildings; core heatup, degradation, and relocation; core-concrete attack; hydrogen production, transport, and combustion; fission product release and transport; and the impact of engineered safety features on thermal-hydraulic and radionuclide behavior. Current uses of MELCOR include estimation of severe accident source terms and their sensitivities and uncertainties in a variety of applications. This publication of the MELCOR computer code manuals corresponds to MELCOR 1.8.3, released to users in August, 1994. Volume 1 contains a primer that describes MELCOR's phenomenological scope, organization (by package), and documentation. The remainder of Volume 1 contains the MELCOR Users Guides, which provide the input instructions and guidelines for each package. Volume 2 contains the MELCOR Reference Manuals, which describe the phenomenological models that have been implemented in each package

  7. Development of PARASOL code

    Energy Technology Data Exchange (ETDEWEB)

    Hosokawa, Masanari [Research Organization for Information Science and Technology, Tokai, Ibaraki (Japan); Takizuka, Tomonori [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

    2000-05-01

    The divertor is expected to play key roles in tokamak reactors, such as ITER, for the heat removal, ash exhaust, and impurity shielding. Its performance is being predicted by using comprehensive simulation codes with the fluid model. In the fluid model for scrape-off layer (SOL) and divertor plasmas, various physics models are introduced. Kinetic approach is required to examine the validity of such physics models. One of the most powerful kinetic models is the particle simulation. Therefore a particle code PARASOL has been developed, and is being used for the simulation study of SOL and divertor plasmas. The PARASOL code treats the plasma bounded by two divertor plates, in which motions of ions and electrons are traced by using a electrostatic PIC method. Effects of Coulomb collisions are simulated by using a Monte-Carlo=method binary collision model. Motions of neutral particles are traced simultaneously with charged particles. In this report, we describe the physics model of PARASOL, the numerical methods, the configuration of the program, input parameters, output formats, samples of simulation results, the parallel computing method. The efficiency of the parallel computing with Paragon XP/S15-256 is demonstrated. (author)

  8. Code Modernization of VPIC

    Science.gov (United States)

    Bird, Robert; Nystrom, David; Albright, Brian

    2017-10-01

    The ability of scientific simulations to effectively deliver performant computation is increasingly being challenged by successive generations of high-performance computing architectures. Code development to support efficient computation on these modern architectures is both expensive, and highly complex; if it is approached without due care, it may also not be directly transferable between subsequent hardware generations. Previous works have discussed techniques to support the process of adapting a legacy code for modern hardware generations, but despite the breakthroughs in the areas of mini-app development, portable-performance, and cache oblivious algorithms the problem still remains largely unsolved. In this work we demonstrate how a focus on platform agnostic modern code-development can be applied to Particle-in-Cell (PIC) simulations to facilitate effective scientific delivery. This work builds directly on our previous work optimizing VPIC, in which we replaced intrinsic based vectorisation with compile generated auto-vectorization to improve the performance and portability of VPIC. In this work we present the use of a specialized SIMD queue for processing some particle operations, and also preview a GPU capable OpenMP variant of VPIC. Finally we include a lessons learnt. Work performed under the auspices of the U.S. Dept. of Energy by the Los Alamos National Security, LLC Los Alamos National Laboratory under contract DE-AC52-06NA25396 and supported by the LANL LDRD program.

  9. Quality Improvement of MARS Code and Establishment of Code Coupling

    International Nuclear Information System (INIS)

    Chung, Bub Dong; Jeong, Jae Jun; Kim, Kyung Doo

    2010-04-01

    The improvement of MARS code quality and coupling with regulatory auditing code have been accomplished for the establishment of self-reliable technology based regulatory auditing system. The unified auditing system code was realized also by implementing the CANDU specific models and correlations. As a part of the quality assurance activities, the various QA reports were published through the code assessments. The code manuals were updated and published a new manual which describe the new models and correlations. The code coupling methods were verified though the exercise of plant application. The education-training seminar and technology transfer were performed for the code users. The developed MARS-KS is utilized as reliable auditing tool for the resolving the safety issue and other regulatory calculations. The code can be utilized as a base technology for GEN IV reactor applications

  10. On Some Ternary LCD Codes

    OpenAIRE

    Darkunde, Nitin S.; Patil, Arunkumar R.

    2018-01-01

    The main aim of this paper is to study $LCD$ codes. Linear code with complementary dual($LCD$) are those codes which have their intersection with their dual code as $\\{0\\}$. In this paper we will give rather alternative proof of Massey's theorem\\cite{8}, which is one of the most important characterization of $LCD$ codes. Let $LCD[n,k]_3$ denote the maximum of possible values of $d$ among $[n,k,d]$ ternary $LCD$ codes. In \\cite{4}, authors have given upper bound on $LCD[n,k]_2$ and extended th...

  11. Design of convolutional tornado code

    Science.gov (United States)

    Zhou, Hui; Yang, Yao; Gao, Hongmin; Tan, Lu

    2017-09-01

    As a linear block code, the traditional tornado (tTN) code is inefficient in burst-erasure environment and its multi-level structure may lead to high encoding/decoding complexity. This paper presents a convolutional tornado (cTN) code which is able to improve the burst-erasure protection capability by applying the convolution property to the tTN code, and reduce computational complexity by abrogating the multi-level structure. The simulation results show that cTN code can provide a better packet loss protection performance with lower computation complexity than tTN code.

  12. Random linear codes in steganography

    Directory of Open Access Journals (Sweden)

    Kamil Kaczyński

    2016-12-01

    Full Text Available Syndrome coding using linear codes is a technique that allows improvement in the steganographic algorithms parameters. The use of random linear codes gives a great flexibility in choosing the parameters of the linear code. In parallel, it offers easy generation of parity check matrix. In this paper, the modification of LSB algorithm is presented. A random linear code [8, 2] was used as a base for algorithm modification. The implementation of the proposed algorithm, along with practical evaluation of algorithms’ parameters based on the test images was made.[b]Keywords:[/b] steganography, random linear codes, RLC, LSB

  13. Containment Code Validation Matrix

    International Nuclear Information System (INIS)

    Chin, Yu-Shan; Mathew, P.M.; Glowa, Glenn; Dickson, Ray; Liang, Zhe; Leitch, Brian; Barber, Duncan; Vasic, Aleks; Bentaib, Ahmed; Journeau, Christophe; Malet, Jeanne; Studer, Etienne; Meynet, Nicolas; Piluso, Pascal; Gelain, Thomas; Michielsen, Nathalie; Peillon, Samuel; Porcheron, Emmanuel; Albiol, Thierry; Clement, Bernard; Sonnenkalb, Martin; Klein-Hessling, Walter; Arndt, Siegfried; Weber, Gunter; Yanez, Jorge; Kotchourko, Alexei; Kuznetsov, Mike; Sangiorgi, Marco; Fontanet, Joan; Herranz, Luis; Garcia De La Rua, Carmen; Santiago, Aleza Enciso; Andreani, Michele; Paladino, Domenico; Dreier, Joerg; Lee, Richard; Amri, Abdallah

    2014-01-01

    The Committee on the Safety of Nuclear Installations (CSNI) formed the CCVM (Containment Code Validation Matrix) task group in 2002. The objective of this group was to define a basic set of available experiments for code validation, covering the range of containment (ex-vessel) phenomena expected in the course of light and heavy water reactor design basis accidents and beyond design basis accidents/severe accidents. It was to consider phenomena relevant to pressurised heavy water reactor (PHWR), pressurised water reactor (PWR) and boiling water reactor (BWR) designs of Western origin as well as of Eastern European VVER types. This work would complement the two existing CSNI validation matrices for thermal hydraulic code validation (NEA/CSNI/R(1993)14) and In-vessel core degradation (NEA/CSNI/R(2001)21). The report initially provides a brief overview of the main features of a PWR, BWR, CANDU and VVER reactors. It also provides an overview of the ex-vessel corium retention (core catcher). It then provides a general overview of the accident progression for light water and heavy water reactors. The main focus is to capture most of the phenomena and safety systems employed in these reactor types and to highlight the differences. This CCVM contains a description of 127 phenomena, broken down into 6 categories: - Containment Thermal-hydraulics Phenomena; - Hydrogen Behaviour (Combustion, Mitigation and Generation) Phenomena; - Aerosol and Fission Product Behaviour Phenomena; - Iodine Chemistry Phenomena; - Core Melt Distribution and Behaviour in Containment Phenomena; - Systems Phenomena. A synopsis is provided for each phenomenon, including a description, references for further information, significance for DBA and SA/BDBA and a list of experiments that may be used for code validation. The report identified 213 experiments, broken down into the same six categories (as done for the phenomena). An experiment synopsis is provided for each test. Along with a test description

  14. Construction of new quantum MDS codes derived from constacyclic codes

    Science.gov (United States)

    Taneja, Divya; Gupta, Manish; Narula, Rajesh; Bhullar, Jaskaran

    Obtaining quantum maximum distance separable (MDS) codes from dual containing classical constacyclic codes using Hermitian construction have paved a path to undertake the challenges related to such constructions. Using the same technique, some new parameters of quantum MDS codes have been constructed here. One set of parameters obtained in this paper has achieved much larger distance than work done earlier. The remaining constructed parameters of quantum MDS codes have large minimum distance and were not explored yet.

  15. Decoding of concatenated codes with interleaved outer codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Thommesen, Christian; Høholdt, Tom

    2004-01-01

    Recently Bleichenbacher et al. proposed a decoding algorithm for interleaved Reed/Solomon codes, which allows close to errors to be corrected in many cases. We discuss the application of this decoding algorithm to concatenated codes. (NK) N-K......Recently Bleichenbacher et al. proposed a decoding algorithm for interleaved Reed/Solomon codes, which allows close to errors to be corrected in many cases. We discuss the application of this decoding algorithm to concatenated codes. (NK) N-K...

  16. Decoding of concatenated codes with interleaved outer codes

    DEFF Research Database (Denmark)

    Justesen, Jørn; Høholdt, Tom; Thommesen, Christian

    2004-01-01

    Recently Bleichenbacher et al. proposed a decoding algorithm for interleaved (N, K) Reed-Solomon codes, which allows close to N-K errors to be corrected in many cases. We discuss the application of this decoding algorithm to concatenated codes.......Recently Bleichenbacher et al. proposed a decoding algorithm for interleaved (N, K) Reed-Solomon codes, which allows close to N-K errors to be corrected in many cases. We discuss the application of this decoding algorithm to concatenated codes....

  17. low bit rate video coding low bit rate video coding

    African Journals Online (AJOL)

    eobe

    Variable length bit rate (VLBR) ariable length bit rate (VLBR) ariable length bit rate (VLBR) broadly encompasses video coding which broadly encompasses video coding which broadly encompasses video coding which mandates a temporal frequency of 10 mandates a temporal frequency of 10 frames per frames per ...

  18. Code Flows : Visualizing Structural Evolution of Source Code

    NARCIS (Netherlands)

    Telea, Alexandru; Auber, David

    2008-01-01

    Understanding detailed changes done to source code is of great importance in software maintenance. We present Code Flows, a method to visualize the evolution of source code geared to the understanding of fine and mid-level scale changes across several file versions. We enhance an existing visual

  19. Qualidade de vida de crianças e adolescentes asmáticos: sua relação com estratégias de enfrentamento materno

    Directory of Open Access Journals (Sweden)

    Gimol Benzaquen Perosa

    2013-06-01

    Full Text Available OBJETIVO: Avaliar a qualidade de vida de crianças e adolescentes asmáticos, sua relação com variáveis sociodemográficas e clínicas e estratégias de enfrentamento materno. MÉTODOS: Estudo transversal no qual crianças e adolescentes com asma responderam a um questionário de qualidade de vida, e suas mães a uma escala de enfrentamento. RESULTADOS: Foram estudadas 42 crianças e adolescentes com idades entre 7 e 15 anos, sendo 74% classificados como tendo um quadro de asma persistente moderada/grave, 19% como persistente leve e 7% asma intermitente; 69% dos entrevistados apresentaram prejuízo na qualidade de vida, com escores médios variando de 4,7 a 3,5 e maior prejuízo no domínio sintomas (escore=3,6. Houve associação significativa entre escolaridade materna e índice geral de qualidade de vida, mas não entre gravidade da asma e tipo de enfrentamento materno. Grande parte das estratégias utilizadas pelas mães para enfrentar as crises do filho estava direcionada ao manejo de estressores ou práticas religiosas, estas com correlação negativa com o índice geral de qualidade de vida da criança, sinalizando que mães cujos filhos tinham pior qualidade de vida usavam mais enfrentamentos religiosos. CONCLUSÕES: Crianças asmáticas, especialmente com asma persistente moderada/grave, apresentaram alterações significativas em sua qualidade de vida. A alta porcentagem de uso de estratégias religiosas por parte das mães, especialmente frente a quadros mais graves, parece indicar que elas se sentem impotentes para atuar, necessitando de orientações concretas e factíveis para uma população de baixa renda.

  20. The Tap code - a code similar to Morse code for communication by tapping

    OpenAIRE

    Rafler, Stephan

    2013-01-01

    A code is presented for fast, easy and efficient communication over channels that allow only two signal types: a single sound (e.g. a knock), or no sound (i.e. silence). This is a true binary code while Morse code is a ternary code and does not work in such situations. Thus the presented code is more universal than Morse and can be used in much more situations. Additionally it is very tolerant to variations in signal strength or duration. The paper contains various ways in which the code can ...

  1. Biological activity of palladium(II) and platinum(II) complexes of the acetone Schiff bases of S-methyl- and S-benzyldithiocarbazate and the X-ray crystal structure of the [Pd(asme)2] (asme=anionic form of the acetone Schiff base of S-methyldithiocarbazate) complex.

    Science.gov (United States)

    Akbar Ali, Mohammad; Mirza, Aminul Huq; Butcher, Raymond J; Tarafder, M T H; Keat, Tan Boon; Ali, A Manaf

    2002-11-25

    Palladium(II) and platinum(II) complexes of general empirical formula, [M(NS)(2)] (NS=uninegatively charged acetone Schiff bases of S-methyl- and S-benzyldithiocarbazate; M=Pt(II) and Pd(II)) have been prepared and characterized by a variety of physicochemical techniques. Based on conductance, IR and electronic spectral evidence, a square-planar structure is assigned to these complexes. The crystal and molecular structure of the [Pd(asme)(2)] complex (asme=anionic form of the acetone Schiff base of S-methyldithiocarbazate) has been determined by X-ray diffraction. The complex has a distorted cis-square planar structure with the ligands coordinated to the palladium(II) ions as uninegatively charged bidentate NS chelating agents via the azomethine nitrogen and the mercaptide sulfur atoms. The distortion from a regular square-planar geometry is attributed to the restricted bite angles of the ligands. Antimicrobial tests indicate that the Schiff bases exhibit strong activities against the pathogenic bacteria, Bacillus subtilis (mutant defective DNA repair), methicillin-resistant Staphylococcus aureus, B. subtilis (wild type) and Pseudomonas aeruginosa and the fungi, Candida albicans (CA), Candida lypotica (2075), Saccharomyces cerevisiae (20341) and Aspergillus ochraceous (398)-the activities exhibited by these compounds being greater than that of the standard antibacterial and antifungal drugs, streptomycin and nystatin, respectively. The palladium(II) and platinum(II) complexes are inactive against most of these organisms but, the microbe, Pseudomonas aeruginosa shows strong sensitivity to the platinum(II) complexes. Screening of the compounds for their cytotoxicities against T-lymphoblastic leukemia cancer cells has shown that the acetone Schiff base of S-methyldithiocarbazate (Hasme) exhibits a very weak activity, whereas the S-benzyl derivative (Hasbz) is inactive. However, the palladium(II) complexes exhibit strong cytotoxicities against this cancer; their

  2. Quick response codes in Orthodontics

    Directory of Open Access Journals (Sweden)

    Moidin Shakil

    2015-01-01

    Full Text Available Quick response (QR code codes are two-dimensional barcodes, which encodes for a large amount of information. QR codes in Orthodontics are an innovative approach in which patient details, radiographic interpretation, and treatment plan can be encoded. Implementing QR code in Orthodontics will save time, reduces paperwork, and minimizes manual efforts in storage and retrieval of patient information during subsequent stages of treatment.

  3. Bar codes for nuclear safeguards

    International Nuclear Information System (INIS)

    Keswani, A.N.; Bieber, A.M. Jr.

    1983-01-01

    Bar codes similar to those used in supermarkets can be used to reduce the effort and cost of collecting nuclear materials accountability data. A wide range of equipment is now commercially available for printing and reading bar-coded information. Several examples of each of the major types of commercially available equipment are given, and considerations are discussed both for planning systems using bar codes and for choosing suitable bar code equipment

  4. The CORSYS neutronics code system

    International Nuclear Information System (INIS)

    Caner, M.; Krumbein, A.D.; Saphier, D.; Shapira, M.

    1994-01-01

    The purpose of this work is to assemble a code package for LWR core physics including coupled neutronics, burnup and thermal hydraulics. The CORSYS system is built around the cell code WIMS (for group microscopic cross section calculations) and 3-dimension diffusion code CITATION (for burnup and fuel management). We are implementing such a system on an IBM RS-6000 workstation. The code was rested with a simplified model of the Zion Unit 2 PWR. (authors). 6 refs., 8 figs., 1 tabs

  5. The path of code linting

    CERN Multimedia

    CERN. Geneva

    2017-01-01

    Join the path of code linting and discover how it can help you reach higher levels of programming enlightenment. Today we will cover how to embrace code linters to offload cognitive strain on preserving style standards in your code base as well as avoiding error-prone constructs. Additionally, I will show you the journey ahead for integrating several code linters in the programming tools your already use with very little effort.

  6. The FLIC conversion codes

    International Nuclear Information System (INIS)

    Basher, J.C.

    1965-05-01

    This report describes the FORTRAN programmes, FLIC 1 and FLIC 2. These programmes convert programmes coded in one dialect of FORTRAN to another dialect of the same language. FLIC 1 is a general pattern recognition and replacement programme whereas FLIC 2 contains extensions directed towards the conversion of FORTRAN II and S2 programmes to EGTRAN 1 - the dialect now in use on the Winfrith KDF9. FII or S2 statements are replaced where possible by their E1 equivalents; other statements which may need changing are flagged. (author)

  7. Physical Layer Network Coding

    OpenAIRE

    Shengli, Zhang; Liew, Soung-Chang; Lam, Patrick P. K.

    2007-01-01

    A main distinguishing feature of a wireless network compared with a wired network is its broadcast nature, in which the signal transmitted by a node may reach several other nodes, and a node may receive signals from several other nodes simultaneously. Rather than a blessing, this feature is treated more as an interference-inducing nuisance in most wireless networks today (e.g., IEEE 802.11). This paper shows that the concept of network coding can be applied at the physical layer to turn the b...

  8. Code Generation with Templates

    CERN Document Server

    Arnoldus, Jeroen; Serebrenik, A

    2012-01-01

    Templates are used to generate all kinds of text, including computer code. The last decade, the use of templates gained a lot of popularity due to the increase of dynamic web applications. Templates are a tool for programmers, and implementations of template engines are most times based on practical experience rather than based on a theoretical background. This book reveals the mathematical background of templates and shows interesting findings for improving the practical use of templates. First, a framework to determine the necessary computational power for the template metalanguage is presen

  9. Cinder begin creative coding

    CERN Document Server

    Rijnieks, Krisjanis

    2013-01-01

    Presented in an easy to follow, tutorial-style format, this book will lead you step-by-step through the multi-faceted uses of Cinder.""Cinder: Begin Creative Coding"" is for people who already have experience in programming. It can serve as a transition from a previous background in Processing, Java in general, JavaScript, openFrameworks, C++ in general or ActionScript to the framework covered in this book, namely Cinder. If you like quick and easy to follow tutorials that will let yousee progress in less than an hour - this book is for you. If you are searching for a book that will explain al

  10. Order functions and evaluation codes

    DEFF Research Database (Denmark)

    Høholdt, Tom; Pellikaan, Ruud; van Lint, Jack

    1997-01-01

    Based on the notion of an order function we construct and determine the parameters of a class of error-correcting evaluation codes. This class includes the one-point algebraic geometry codes as wella s the generalized Reed-Muller codes and the parameters are detremined without using the heavy...... machinery of algebraic geometry....

  11. Network Coding Over The 232

    DEFF Research Database (Denmark)

    Pedersen, Morten Videbæk; Heide, Janus; Vingelmann, Peter

    2013-01-01

    Creating efficient finite field implementations has been an active research topic for several decades. Many appli- cations in areas such as cryptography, signal processing, erasure coding and now also network coding depend on this research to deliver satisfactory performance. In this paper we...... will be useful in many network coding applications where large field sizes are required....

  12. Sub-Transport Layer Coding

    DEFF Research Database (Denmark)

    Hansen, Jonas; Krigslund, Jeppe; Roetter, Daniel Enrique Lucani

    2014-01-01

    oblivious to the congestion control algorithms of the utilised transport layer protocol. Although our coding shim is indifferent towards the transport layer protocol, we focus on the performance of TCP when ran on top of our proposed coding mechanism due to its widespread use. The coding shim provides gains...

  13. Strongly-MDS convolutional codes

    NARCIS (Netherlands)

    Gluesing-Luerssen, H; Rosenthal, J; Smarandache, R

    Maximum-distance separable (MDS) convolutional codes have the property that their free distance is maximal among all codes of the same rate and the same degree. In this paper, a class of MDS convolutional codes is introduced whose column distances reach the generalized Singleton bound at the

  14. Geochemical computer codes. A review

    International Nuclear Information System (INIS)

    Andersson, K.

    1987-01-01

    In this report a review of available codes is performed and some code intercomparisons are also discussed. The number of codes treating natural waters (groundwater, lake water, sea water) is large. Most geochemical computer codes treat equilibrium conditions, although some codes with kinetic capability are available. A geochemical equilibrium model consists of a computer code, solving a set of equations by some numerical method and a data base, consisting of thermodynamic data required for the calculations. There are some codes which treat coupled geochemical and transport modeling. Some of these codes solve the equilibrium and transport equations simultaneously while other solve the equations separately from each other. The coupled codes require a large computer capacity and have thus as yet limited use. Three code intercomparisons have been found in literature. It may be concluded that there are many codes available for geochemical calculations but most of them require a user that us quite familiar with the code. The user also has to know the geochemical system in order to judge the reliability of the results. A high quality data base is necessary to obtain a reliable result. The best results may be expected for the major species of natural waters. For more complicated problems, including trace elements, precipitation/dissolution, adsorption, etc., the results seem to be less reliable. (With 44 refs.) (author)

  15. Authorship Attribution of Source Code

    Science.gov (United States)

    Tennyson, Matthew F.

    2013-01-01

    Authorship attribution of source code is the task of deciding who wrote a program, given its source code. Applications include software forensics, plagiarism detection, and determining software ownership. A number of methods for the authorship attribution of source code have been presented in the past. A review of those existing methods is…

  16. Separate Turbo Code and Single Turbo Code Adaptive OFDM Transmissions

    Directory of Open Access Journals (Sweden)

    Burr Alister

    2009-01-01

    Full Text Available Abstract This paper discusses the application of adaptive modulation and adaptive rate turbo coding to orthogonal frequency-division multiplexing (OFDM, to increase throughput on the time and frequency selective channel. The adaptive turbo code scheme is based on a subband adaptive method, and compares two adaptive systems: a conventional approach where a separate turbo code is used for each subband, and a single turbo code adaptive system which uses a single turbo code over all subbands. Five modulation schemes (BPSK, QPSK, 8AMPM, 16QAM, and 64QAM are employed and turbo code rates considered are and . The performances of both systems with high ( and low ( BER targets are compared. Simulation results for throughput and BER show that the single turbo code adaptive system provides a significant improvement.

  17. Separate Turbo Code and Single Turbo Code Adaptive OFDM Transmissions

    Directory of Open Access Journals (Sweden)

    Lei Ye

    2009-01-01

    Full Text Available This paper discusses the application of adaptive modulation and adaptive rate turbo coding to orthogonal frequency-division multiplexing (OFDM, to increase throughput on the time and frequency selective channel. The adaptive turbo code scheme is based on a subband adaptive method, and compares two adaptive systems: a conventional approach where a separate turbo code is used for each subband, and a single turbo code adaptive system which uses a single turbo code over all subbands. Five modulation schemes (BPSK, QPSK, 8AMPM, 16QAM, and 64QAM are employed and turbo code rates considered are 1/2 and 1/3. The performances of both systems with high (10−2 and low (10−4 BER targets are compared. Simulation results for throughput and BER show that the single turbo code adaptive system provides a significant improvement.

  18. Quantum Codes From Cyclic Codes Over The Ring R 2

    International Nuclear Information System (INIS)

    Altinel, Alev; Güzeltepe, Murat

    2016-01-01

    Let R 2 denotes the ring F 2 + μF 2 + υ 2 + μυ F 2 + wF 2 + μwF 2 + υwF 2 + μυwF 2 . In this study, we construct quantum codes from cyclic codes over the ring R 2 , for arbitrary length n, with the restrictions μ 2 = 0, υ 2 = 0, w 2 = 0, μυ = υμ, μw = wμ, υw = wυ and μ (υw) = (μυ) w. Also, we give a necessary and sufficient condition for cyclic codes over R 2 that contains its dual. As a final point, we obtain the parameters of quantum error-correcting codes from cyclic codes over R 2 and we give an example of quantum error-correcting codes form cyclic codes over R 2 . (paper)

  19. Genetic code for sine

    Science.gov (United States)

    Abdullah, Alyasa Gan; Wah, Yap Bee

    2015-02-01

    The computation of the approximate values of the trigonometric sines was discovered by Bhaskara I (c. 600-c.680), a seventh century Indian mathematician and is known as the Bjaskara's I's sine approximation formula. The formula is given in his treatise titled Mahabhaskariya. In the 14th century, Madhava of Sangamagrama, a Kerala mathematician astronomer constructed the table of trigonometric sines of various angles. Madhava's table gives the measure of angles in arcminutes, arcseconds and sixtieths of an arcsecond. The search for more accurate formulas led to the discovery of the power series expansion by Madhava of Sangamagrama (c.1350-c. 1425), the founder of the Kerala school of astronomy and mathematics. In 1715, the Taylor series was introduced by Brook Taylor an English mathematician. If the Taylor series is centered at zero, it is called a Maclaurin series, named after the Scottish mathematician Colin Maclaurin. Some of the important Maclaurin series expansions include trigonometric functions. This paper introduces the genetic code of the sine of an angle without using power series expansion. The genetic code using square root approach reveals the pattern in the signs (plus, minus) and sequence of numbers in the sine of an angle. The square root approach complements the Pythagoras method, provides a better understanding of calculating an angle and will be useful for teaching the concepts of angles in trigonometry.

  20. Supervised Transfer Sparse Coding

    KAUST Repository

    Al-Shedivat, Maruan

    2014-07-27

    A combination of the sparse coding and transfer learn- ing techniques was shown to be accurate and robust in classification tasks where training and testing objects have a shared feature space but are sampled from differ- ent underlying distributions, i.e., belong to different do- mains. The key assumption in such case is that in spite of the domain disparity, samples from different domains share some common hidden factors. Previous methods often assumed that all the objects in the target domain are unlabeled, and thus the training set solely comprised objects from the source domain. However, in real world applications, the target domain often has some labeled objects, or one can always manually label a small num- ber of them. In this paper, we explore such possibil- ity and show how a small number of labeled data in the target domain can significantly leverage classifica- tion accuracy of the state-of-the-art transfer sparse cod- ing methods. We further propose a unified framework named supervised transfer sparse coding (STSC) which simultaneously optimizes sparse representation, domain transfer and classification. Experimental results on three applications demonstrate that a little manual labeling and then learning the model in a supervised fashion can significantly improve classification accuracy.

  1. Efeito do EGB761 (Extrato de Ginkgo biloba sobre a qualidade de vida em pacientes asmáticos moderados submetidos a tratamento de manutenção

    Directory of Open Access Journals (Sweden)

    M. D. Hillebrand

    Full Text Available A busca de tratamentos alternativos e eficazes para o controle da asma brônquica é fator importante na melhora da qualidade de vida dos portadores da doença. O efeito do extrato de Ginkgo biloba (Ginkgo biloba L., na resposta asmática ao tratamento de manutenção para asma brônquica moderada persistente, foi estudado em um ensaio clínico randomizado, cego, placebo controlado.

  2. Removal of Antibiotics in Biological Wastewater Treatment Systems-A Critical Assessment Using the Activated Sludge Modeling Framework for Xenobiotics (ASM-X).

    Science.gov (United States)

    Polesel, Fabio; Andersen, Henrik R; Trapp, Stefan; Plósz, Benedek Gy

    2016-10-04

    Many scientific studies present removal efficiencies for pharmaceuticals in laboratory-, pilot-, and full-scale wastewater treatment plants, based on observations that may be impacted by theoretical and methodological approaches used. In this Critical Review, we evaluated factors influencing observed removal efficiencies of three antibiotics (sulfamethoxazole, ciprofloxacin, tetracycline) in pilot- and full-scale biological treatment systems. Factors assessed include (i) retransformation to parent pharmaceuticals from e.g., conjugated metabolites and analogues, (ii) solid retention time (SRT), (iii) fractions sorbed onto solids, and (iv) dynamics in influent and effluent loading. A recently developed methodology was used, relying on the comparison of removal efficiency predictions (obtained with the Activated Sludge Model for Xenobiotics (ASM-X)) with representative measured data from literature. By applying this methodology, we demonstrated that (a) the elimination of sulfamethoxazole may be significantly underestimated when not considering retransformation from conjugated metabolites, depending on the type (urban or hospital) and size of upstream catchments; (b) operation at extended SRT may enhance antibiotic removal, as shown for sulfamethoxazole; (c) not accounting for fractions sorbed in influent and effluent solids may cause slight underestimation of ciprofloxacin removal efficiency. Using tetracycline as example substance, we ultimately evaluated implications of effluent dynamics and retransformation on environmental exposure and risk prediction.

  3. Evolución clínica de pacientes asmáticos tratados con inmunoterapia. Municipio Majibacoa, 2008-2013

    Directory of Open Access Journals (Sweden)

    Mailin Molina Leyva

    2015-11-01

    Full Text Available Se realizó un estudio cuasi-experimental de corte longitudinal en 50 pacientes asmáticos con edades  entre 5 y 54 años, atendidos en el Servicio de Alergología del municipio Majibacoa de la provincia de Las Tunas; con el objetivo de determinar la evolución clínica con inmunoterapia, en el período de enero 2008 a febrero de 2013. A los pacientes se les administró inmunoterapia específica de ácaros con extractos estandarizados, durante tres años o más de forma subcutánea. El asma bronquial predominó en el sexo femenino y en las edades comprendidas entre 5 y 14 años. Los antecedentes de atopia familiar fueron referidos por el mayor por ciento de los pacientes analizados. Según severidad de la enfermedad, antes del tratamiento prevalecieron los pacientes en la categoría persistente moderada. Se observó mejoría de los síntomas del asma en una elevada proporción de casos.

  4. Evidence of Two Component Accretion Flows as revealed by time lag properties: Results of Long-Term RXTE/ASM Data Analysis

    Science.gov (United States)

    Ghosh, Arindam; Chakrabarti, Sandip Kumar

    2016-07-01

    Long-term RXTE/ASM X-ray data of several Galactic black hole candidates (BHCs) are analyzed. The results of this analysis show the existence of two component accretion flow (TCAF) in both low-mass and high-mass X-ray binaries (LMXBs & HMXBs). Large disks with long viscous timescales in the accreting matter with high angular momentum are prevalent in LMXBs due to processes like Roche lobe overflow, while small disks with little viscous delays are observed in HMXBs, primarily because of wind accretion. Two parameters are defined as photon indices, independent of the choice of a BHC, in order to find correlation between the two components, namely, the Keplerian disk component and the sub-Keplerian component, thereby estimating the time lag between two aforesaid timescales. Fluxes of hard and soft photons are observed to be anti-correlated with respect to these photon indices. The time lags give us an idea of the viscosity in the Keplerian component.

  5. Periodic X-ray Modulation and its Possible Relation with Eccentricity in Black Hole Binaries : Long-Term Swift/BAT and RXTE/ASM Data Analysis

    Science.gov (United States)

    Ghosh, Arindam; Chakrabarti, Sandip Kumar

    2016-07-01

    X-ray binary orbits are expected to have some eccentricity, albeit small. Stellar companion of a black hole orbiting in an eccentric orbit will experience modulating tidal force with a periodicity same as that of the orbital period which will result in a modulation of accretion rates, seed photon flux, and flux of inverse Comptonized harder X-rays as well. Timing analysis of long-term X-ray data (1.5-12 keV) of RXTE/ASM and all sky survey data (15-50 keV) of Swift/BAT satellites reveal this periodicity in several black hole candidates. If this modulation is assumed to be solely due to tidal effects (without taking other effects, such as eclipses, reflection from winds, super-hump phenomena etc. into account), the RMS-value of the peak in power density spectrum allows us to estimate eccentricities of these orbits. We present these very interesting results. We show that our results generally agree with independent studies of these parameters.

  6. The systemic family assessment system: its validity with asthmatic children and their families Evaluación familiar sistémica: su validez con niños asmáticos y sus familias Avaliação familiar sistêmica: sua validade com crianças asmáticas e suas famílias

    Directory of Open Access Journals (Sweden)

    Dóris Lieth Peçanha

    2007-12-01

    Full Text Available The construct and concurrent validity of the Systemic Family Assessment (SFA system was tested. Participants were 11 asthmatic and 14 healthy Brazilian children (aged 5 to 9 along with their intact families. Measures included the SFA, the Family Colored Drawing Test with children (FCDT, and a semi-structured interview with parents (PI. Comparisons between families of asthmatic and healthy children yielded significant differences for all family dimensions of the SFA. The most affected dimensions for families of asthmatic children were the individuation process within the family, family conflicts, family integration and cohesion, roles, and quality of leadership within the family. Significative correlation between the SFA and the two independent measures were found. Results support the construct and concurrent validity of the SFA.La validez de constructo y la validad coexistente do protocolo de Evaluación Familiar Sistémica (EFS fue establecida. El estudio fue realizado en Brasil con familias intactas, y observó 11 niños con asma y 14 saludables, con edades de 5 a 9 años. Las medidas analizadas incluyeron el EFS, el Test del Dibujo Coloreado de la Familia aplicado a los niños (TDCF, y una entrevista semi-estructurada aplicada a los padres (EP. Las comparaciones entre las familias de niños asmáticos y saludables apuntaron diferencias significativas en todas las dimensiones familiares de la EFS. En las familias de niños asmáticos las dimensiones más afectadas fueron el proceso de la individuación dentro de la familia, los conflictos familiares, la integración familiar y la cohesión, los papeles y la calidad de liderazgo dentro de la familia. Se encontró una correlación significativa entre el EFS y las dos medidas independientes. Los resultados prueban la validez del constructo y la validad coexistente del EFS.Foi testada a validade de construto e a validade concorrente do protocolo de Avaliação Familiar Sistêmica (AFS. Os

  7. Continuous Non-malleable Codes

    DEFF Research Database (Denmark)

    Faust, Sebastian; Mukherjee, Pratyay; Nielsen, Jesper Buus

    2014-01-01

    Non-malleable codes are a natural relaxation of error correcting/ detecting codes that have useful applications in the context of tamper resilient cryptography. Informally, a code is non-malleable if an adversary trying to tamper with an encoding of a given message can only leave it unchanged or ...... applications of non-malleable codes in this setting required to perfectly erase the entire memory after each execution and required the adversary to be restricted in memory. We show that continuous non-malleable codes avoid these restrictions....

  8. The Art of Readable Code

    CERN Document Server

    Boswell, Dustin

    2011-01-01

    As programmers, we've all seen source code that's so ugly and buggy it makes our brain ache. Over the past five years, authors Dustin Boswell and Trevor Foucher have analyzed hundreds of examples of "bad code" (much of it their own) to determine why they're bad and how they could be improved. Their conclusion? You need to write code that minimizes the time it would take someone else to understand it-even if that someone else is you. This book focuses on basic principles and practical techniques you can apply every time you write code. Using easy-to-digest code examples from different languag

  9. A Comparison of the Variability of the Symbiotic X-ray Binaries GX 1+4, 4U 1954+31, and 4U 1700+24 from Swift/BAT and RXTE/ASM Observations

    Science.gov (United States)

    Corbet, R. H. D.; Sokoloski, J. L.; Mukai, K.; Markwardt, C. B.; Tueller, J.

    2007-01-01

    We present an analysis of the X-ray variability of three symbiotic X-ray binaries, GX 1+4, 4U 1700+24, and 4U 1954+31, using observations made with the Swift Burst Alert Telescope (BAT) and the Rossi X-ray Timing Explorer (RXTE) All-Sky Monitor (ASM). Observations of 4U 1954+31 with the Swift BAT show modulation at a period near 5 hours. Models to explain this modulation are discussed including the presence of an exceptionally slow X-ray pulsar in the system and accretion instabilities. We conclude that the most likely interpretation is that 4U 1954+31 contains one of the slowest known X-ray pulsars. Unlike 4U 1954+31, neither GX 1+4 nor 4U 1700+24 show any evidence for modulation on a timescale of hours. An analysis of the RXTE ASM light curves of GX l+4, 4U 1700+24, and 4U 1954+31 does not show the presence of periodic modulation in any source, although there is considerable variability on long timescales for all three sources. There is no modulation in GX 1+4 on either the optical 1161 day orbital period or a previously reported 304 day X-ray period. For 4U 1700+24 we do not confirm the 404 day period previously proposed for this source from a shorter duration ASM light curve.

  10. Elements of algebraic coding systems

    CERN Document Server

    Cardoso da Rocha, Jr, Valdemar

    2014-01-01

    Elements of Algebraic Coding Systems is an introductory text to algebraic coding theory. In the first chapter, you'll gain inside knowledge of coding fundamentals, which is essential for a deeper understanding of state-of-the-art coding systems. This book is a quick reference for those who are unfamiliar with this topic, as well as for use with specific applications such as cryptography and communication. Linear error-correcting block codes through elementary principles span eleven chapters of the text. Cyclic codes, some finite field algebra, Goppa codes, algebraic decoding algorithms, and applications in public-key cryptography and secret-key cryptography are discussed, including problems and solutions at the end of each chapter. Three appendices cover the Gilbert bound and some related derivations, a derivation of the Mac- Williams' identities based on the probability of undetected error, and two important tools for algebraic decoding-namely, the finite field Fourier transform and the Euclidean algorithm f...

  11. Introduction of SCIENCE code package

    International Nuclear Information System (INIS)

    Lu Haoliang; Li Jinggang; Zhu Ya'nan; Bai Ning

    2012-01-01

    The SCIENCE code package is a set of neutronics tools based on 2D assembly calculations and 3D core calculations. It is made up of APOLLO2F, SMART and SQUALE and used to perform the nuclear design and loading pattern analysis for the reactors on operation or under construction of China Guangdong Nuclear Power Group. The purpose of paper is to briefly present the physical and numerical models used in each computation codes of the SCIENCE code pack age, including the description of the general structure of the code package, the coupling relationship of APOLLO2-F transport lattice code and SMART core nodal code, and the SQUALE code used for processing the core maps. (authors)

  12. Galois LCD Codes over Finite Fields

    OpenAIRE

    Liu, Xiusheng; Fan, Yun; Liu, Hualu

    2017-01-01

    In this paper, we study the complementary dual codes in more general setting (which are called Galois LCD codes) by a uniform method. A necessary and sufficient condition for linear codes to be Galois LCD codes is determined, and constacyclic codes to be Galois LCD codes are characterized. Some illustrative examples which constacyclic codes are Galois LCD MDS codes are provided as well. In particular, we study Hermitian LCD constacyclic codes. Finally, we present a construction of a class of ...

  13. GOC: General Orbit Code

    International Nuclear Information System (INIS)

    Maddox, L.B.; McNeilly, G.S.

    1979-08-01

    GOC (General Orbit Code) is a versatile program which will perform a variety of calculations relevant to isochronous cyclotron design studies. In addition to the usual calculations of interest (e.g., equilibrium and accelerated orbits, focusing frequencies, field isochronization, etc.), GOC has a number of options to calculate injections with a charge change. GOC provides both printed and plotted output, and will follow groups of particles to allow determination of finite-beam properties. An interactive PDP-10 program called GIP, which prepares input data for GOC, is available. GIP is a very easy and convenient way to prepare complicated input data for GOC. Enclosed with this report are several microfiche containing source listings of GOC and other related routines and the printed output from a multiple-option GOC run

  14. Code des baux 2018

    CERN Document Server

    Vial-Pedroletti, Béatrice; Kendérian, Fabien; Chavance, Emmanuelle; Coutan-Lapalus, Christelle

    2017-01-01

    Le code des baux 2018 vous offre un contenu extrêmement pratique, fiable et à jour au 1er août 2017. Cette 16e édition intègre notamment : le décret du 27 juillet 2017 relatif à l’évolution de certains loyers dans le cadre d’une nouvelle location ou d’un renouvellement de bail, pris en application de l’article 18 de la loi n° 89-462 du 6 juillet 1989 ; la loi du 27 janvier 2017 relative à l’égalité et à la citoyenneté ; la loi du 9 décembre 2016 relative à la transparence, à la lutte contre la corruption et à la modernisation de la vie économique ; la loi du 18 novembre 2016 de modernisation de la justice du xxie siècle

  15. Entanglement-assisted quantum MDS codes from negacyclic codes

    Science.gov (United States)

    Lu, Liangdong; Li, Ruihu; Guo, Luobin; Ma, Yuena; Liu, Yang

    2018-03-01

    The entanglement-assisted formalism generalizes the standard stabilizer formalism, which can transform arbitrary classical linear codes into entanglement-assisted quantum error-correcting codes (EAQECCs) by using pre-shared entanglement between the sender and the receiver. In this work, we construct six classes of q-ary entanglement-assisted quantum MDS (EAQMDS) codes based on classical negacyclic MDS codes by exploiting two or more pre-shared maximally entangled states. We show that two of these six classes q-ary EAQMDS have minimum distance more larger than q+1. Most of these q-ary EAQMDS codes are new in the sense that their parameters are not covered by the codes available in the literature.

  16. Diagonal Eigenvalue Unity (DEU) code for spectral amplitude coding-optical code division multiple access

    Science.gov (United States)

    Ahmed, Hassan Yousif; Nisar, K. S.

    2013-08-01

    Code with ideal in-phase cross correlation (CC) and practical code length to support high number of users are required in spectral amplitude coding-optical code division multiple access (SAC-OCDMA) systems. SAC systems are getting more attractive in the field of OCDMA because of its ability to eliminate the influence of multiple access interference (MAI) and also suppress the effect of phase induced intensity noise (PIIN). In this paper, we have proposed new Diagonal Eigenvalue Unity (DEU) code families with ideal in-phase CC based on Jordan block matrix with simple algebraic ways. Four sets of DEU code families based on the code weight W and number of users N for the combination (even, even), (even, odd), (odd, odd) and (odd, even) are constructed. This combination gives DEU code more flexibility in selection of code weight and number of users. These features made this code a compelling candidate for future optical communication systems. Numerical results show that the proposed DEU system outperforms reported codes. In addition, simulation results taken from a commercial optical systems simulator, Virtual Photonic Instrument (VPI™) shown that, using point to multipoint transmission in passive optical network (PON), DEU has better performance and could support long span with high data rate.

  17. Selection of Code and Interleaver for Turbo Coding

    DEFF Research Database (Denmark)

    Andersen, Jakob Dahl

    1998-01-01

    The selection of component codes for turbo coding has often been based on the performance at high SNR's. However, we will argue that the selection mainly should be based on the performance at low SNR's, i.e. the convergence properties. Further, we will present a way to construct interleavers...... that significantly improve the performance of the turbo coding scheme at high SNR's, i.e. lowers the error floor...

  18. Stochastic Decoding of Turbo Codes

    OpenAIRE

    Dong , Q. T.; ARZEL , Matthieu; Jego , Christophe; Gross , W. J.

    2010-01-01

    International audience; Stochastic computation is a technique in which operations on probabilities are performed on random bit streams. Stochastic decoding of forward error-correction (FEC) codes is inspired by this technique. This paper extends the application of the stochastic decoding approach to the families of convolutional codes and turbo codes. It demonstrates that stochastic computation is a promising solution to improve the data throughput of turbo decoders with very simple implement...

  19. Evaluación clínica y funcional en niños asmáticos tratados con montelukast

    Directory of Open Access Journals (Sweden)

    Concepción Sánchez Infante

    2011-09-01

    Full Text Available Introducción: el asma bronquial es una enfermedad que se considera puede ser controlable, aunque no puede curarse, pero sus manifestaciones clínicas, que son las que afectan al paciente, pueden desaparecer o disminuir hasta lograr una vida normal, o casi normal, para este y sus familiares, con una serie de medidas medicamentosas y no medicamentosas. Objetivo: evaluar la eficacia del montelukast en el tratamiento de niños asmáticos persistentes. Métodos: se realizó un estudio en 65 niños asmáticos persistentes en el Hospital Pediátrico Universitario "William Soler". Se evaluaron los síntomas, pruebas funcionales respiratorias, días perdidos en la escuela, y control de la enfermedad, inicialmente, y un año después de la introducción del montelukast. Se observó la posibilidad de efectos secundarios. Resultados: 55 pacientes (84,6 % tenían tos nocturna diaria antes del tratamiento. Al año, la tos nocturna diaria se observó solo en 9 (13,9 %; 43 (66,1 % presentaban sibilancias al reírse, mientras que al año 1 (1,6 % mantenía sibilancias diarias con la risa; 41 (63,0 % tenían, inicialmente, afectación de la actividad física, mientras que al año 51 (78,4 % no tenían limitaciones. El 100 % tenía ausencias escolares. Durante el año de tratamiento 34 (57,0 % no presentaron días perdidos; 42 (64,6 % tenían crisis diarias, sin embargo, al reevaluar, 38 (58,5 % no tuvieron crisis. Habían tenido ingresos hospitalarios 23 (35,4 %, pero posteriormente solo 5 necesitaron hospitalización. Antes del tratamiento, 49 (75,0 % necesitaron tratamiento de rescate, en cambio, durante el año disminuyó a 27 (41,0 %. 19 niños (38,0 % tenían inicialmente el volumen espiratorio forzado en 1 s menor del 80 %, y solamente 8 (16,0 % posteriormente. Antes del tratamiento el 100 % de los pacientes tenían asma no controlada o parcialmente controlada, mientras que al año el 57 % tenía el asma controlada. No se observaron reacciones adversas

  20. An algebraic approach to graph codes

    DEFF Research Database (Denmark)

    Pinero, Fernando

    theory as evaluation codes. Chapter three consists of the introduction to graph based codes, such as Tanner codes and graph codes. In Chapter four, we compute the dimension of some graph based codes with a result combining graph based codes and subfield subcodes. Moreover, some codes in chapter four...... are optimal or best known for their parameters. In chapter five we study some graph codes with Reed–Solomon component codes. The underlying graph is well known and widely used for its good characteristics. This helps us to compute the dimension of the graph codes. We also introduce a combinatorial concept...... related to the iterative encoding of graph codes with MDS component code. The last chapter deals with affine Grassmann codes and Grassmann codes. We begin with some previously known codes and prove that they are also Tanner codes of the incidence graph of the point–line partial geometry...